In-line Microwave Warmer for Blood and Intravenous Fluids.

DTIC Science & Technology

1989-12-14

circuit was designed and tested. This circuit uses a digitally controlled optically coupled Triac , a thyristor device, which acts as a switch to allow...three sites of the circuit : Inlet Port of Heating Chamber Interior Path of Heating Chamber Outlet Port of Heating Chamber 4) Feedback Control Mechanism...accomplished through use of a closed loop test circuit depicted in Figure 1-2. This test circuit can be used to heat iv fluids or blood on a continuous

Logistics and Operational Effectiveness of the P-3 Aircraft.

DTIC Science & Technology

1977-03-01

Memory Module Tester for the AIMD at HAS Jacksonville Module Caddy utilization for the Position Indicator Failure rate and spares availability of the...into the P—3 aircraft • Investigated TRIAC failures in the AN/AQA-7(V) Sonar Computer Recorder Group • Identified and investigated incorrect use of...Magnetic Tape Transport: Replacement vacuum blower motors Piece parts for A7A1 circuit board • Investigated the availability of spare HI/LO Backward Wave

Aircraft Material Fire Test Handbook

DTIC Science & Technology

1990-09-01

becomes extinguished for any period that exceeds 3 sec. A circuit for a satisfactory device is sketched in Figure 5-4. 5.3.8.2 Upper Pilot Burner An...34A model 470 Series Power controller manufactured by Eurotherm, a Model 3AEV 1B IOC I Triac manufactured by General Electric Co, or equivalent have...Compartment (galley or lavatory module ) An enclosure or shell structure with access provisions, such as a waste chute opening or doors, designed for

Design Considerations for Gun Propellant Climatic Storage Chambers.

DTIC Science & Technology

1982-11-01

Schematic diagram of thermal element 5 4. Prototype Lhermal element 6 5. Power control circuit diagram 7 6. Power control module 7 7. Temperature...plates. Each plate is powered through a triac and temperature control circuit as shown in figure 5. Figure 6 is a photograph of an assembled power control...SHEATER PLATES Figure 5. Power control circuit diagram 4 f Figure 6. Power control module WSR.L-0295-TR -8- Figure 7. Temperature control module 9 -WSRL

Intelligent Load Manager (LOADMAN): Application of Expert System Technology to Load Management Problems in Power Generation and Distribution Systems

DTIC Science & Technology

1988-08-10

addrsesed to it, the wall-receptacle module energizes a relay. Modules can be built to use a triac instead and have the capacity to increase or decrease... modulated by other constraints for a safe, functional ana effective power distribution system. 2.2.3 BackuR Equipment Alternate power sources are...environments have limited sensor capability and no remote control capability. However, future enhancements to current equipment, such as frequency- modulated

Materials-Process Interactions in Ternary Alloy Semiconductors.

DTIC Science & Technology

1984-08-01

high, the surface potential can be * modulated . PECVD SiO. appears to be a viable candidate as a gate dielectric for * Irf ,fO-4A)s MISFETs...it is desirable to integrate the detectors with circuits capable of performing signal processing functions. These circuits can either be fabricated in...to be a major problem in In0. 5 3Ga 0.* 47 s. 25 S. . . . . 13821 -1 R I (a) CROSS SECTION KEYBOARD 210M ANNEALING CHAMBER GATE TRIGG TRIAC

Reduced hepatitis B and D viral entry using clinically applied drugs as novel inhibitors of the bile acid transporter NTCP.

PubMed

Donkers, Joanne M; Zehnder, Benno; van Westen, Gerard J P; Kwakkenbos, Mark J; IJzerman, Adriaan P; Oude Elferink, Ronald P J; Beuers, Ulrich; Urban, Stephan; van de Graaf, Stan F J

2017-11-10

The sodium taurocholate co-transporting polypeptide (NTCP, SLC10A1) is the main hepatic transporter of conjugated bile acids, and the entry receptor for hepatitis B virus (HBV) and hepatitis delta virus (HDV). Myrcludex B, a synthetic peptide mimicking the NTCP-binding domain of HBV, effectively blocks HBV and HDV infection. In addition, Myrcludex B inhibits NTCP-mediated bile acid uptake, suggesting that also other NTCP inhibitors could potentially be a novel treatment of HBV/HDV infection. This study aims to identify clinically-applied compounds intervening with NTCP-mediated bile acid transport and HBV/HDV infection. 1280 FDA/EMA-approved drugs were screened to identify compounds that reduce uptake of taurocholic acid and lower Myrcludex B-binding in U2OS cells stably expressing human NTCP. HBV/HDV viral entry inhibition was studied in HepaRG cells. The four most potent inhibitors of human NTCP were rosiglitazone (IC 50 5.1 µM), zafirlukast (IC 50 6.5 µM), TRIAC (IC 50 6.9 µM), and sulfasalazine (IC 50 9.6 µM). Chicago sky blue 6B (IC 50 7.1 µM) inhibited both NTCP and ASBT, a distinct though related bile acid transporter. Rosiglitazone, zafirlukast, TRIAC, sulfasalazine, and chicago sky blue 6B reduced HBV/HDV infection in HepaRG cells in a dose-dependent manner. Five out of 1280 clinically approved drugs were identified that inhibit NTCP-mediated bile acid uptake and HBV/HDV infection in vitro.

Test Results for the 2.5-kVA Ground Fault Detector.

DTIC Science & Technology

1986-01-01

powered through Q1 is delayed in turning off by capacitor C4 for approximately 12 msec. When the relay does drop out, the triac Q7 (a bidirectional...SECONDS) CALBIRATIONS, ETC.) / / -. L a 2 33 ( j4 -40 7 S’f9 I! Note time of con pletlon o test series . .I1 " , -3 TEST DATA FORM Bc (CONTINUATION...test series . 2 *51/7 ,6. L7.. i K-t TEST CATA FORM D OCEAN OPERABILITY TESTS FOR ELEETRIC FIELD DETECTOR AND GROUND FAULT DETECTORS This data form is to

[Long term follow up of medical treatment of differentiated thyroid cancer].

PubMed

Jaffiol, C; Daures, J P; Nsakala, N; Guerenova, J; Baldet, L; Pujol, P; Vannereau, D; Bringer, J

1995-01-01

106 patients, 114 W, 27 M, were thyroidectomized for differentiated thyroid cancer (follicular 29.3%-papillary 54.3%) with different stages of gravity (NO: 48.2% - N1: 32.8% - N2: 19%). Neck dissection was used in cases of involved nodes. One or several doses of 131 I were given to 126 subjects, 106 patients were treated with LT4 (mean daily dose: 2.5 micrograms/kg BW). 23 patients presenting intolerance to LT4 with non suppressed TSH for 13 of them were treated by an association of TRIAC + LT4. The follow up included a yearly check up involving clinical examination, plasma Tg and TSH assessment, neck ultrasonography and X-ray of the chest. Therapy was stopped for 4 weeks in cases with Tg above its detectable value and a total body scan performed with Tg and TSH controls. The mean duration of follow up was 94.5 +/- 67.7 months and extended to more than 5 years for 61% of the patients. We observed 22 relapses of the tumor with 4 deaths. Age less then 45 years, appears as the best factor of prognosis. 2 groups of patients were compared to evaluate the incidence of TSH suppression on the relapse free survival (group 1 n = 30 with a TSH < or = 0.10 mU/l and group 2 n = 15 with a TSH always > 1 mU/l during the follow up). The relapse free survival was shorter in group 2 (p = 0.01). Association of TRIAC with LT4 leads to a reduction of the daily dose of LT4 (m = 25 micrograms/day) with a significant improvement of TSH suppression and clinical tolerance.(ABSTRACT TRUNCATED AT 250 WORDS)

Generalized type II hybrid ARQ scheme using punctured convolutional coding

NASA Astrophysics Data System (ADS)

Kallel, Samir; Haccoun, David

1990-11-01

A method is presented to construct rate-compatible convolutional (RCC) codes from known high-rate punctured convolutional codes, obtained from best-rate 1/2 codes. The construction method is rather simple and straightforward, and still yields good codes. Moreover, low-rate codes can be obtained without any limit on the lowest achievable code rate. Based on the RCC codes, a generalized type-II hybrid ARQ scheme, which combines the benefits of the modified type-II hybrid ARQ strategy of Hagenauer (1988) with the code-combining ARQ strategy of Chase (1985), is proposed and analyzed. With the proposed generalized type-II hybrid ARQ strategy, the throughput increases as the starting coding rate increases, and as the channel degrades, it tends to merge with the throughput of rate 1/2 type-II hybrid ARQ schemes with code combining, thus allowing the system to be flexible and adaptive to channel conditions, even under wide noise variations and severe degradations.

Effectiveness of teaching International Caries Detection and Assessment System II and its e-learning program to freshman dental students on occlusal caries detection

PubMed Central

El-Damanhoury, Hatem M.; Fakhruddin, Kausar Sadia; Awad, Manal A.

2014-01-01

Objective: To assess the feasibility of teaching International Caries Detection and Assessment System (ICDAS) II and its e-learning program as tools for occlusal caries detection to freshmen dental students in comparison to dental graduates with 2 years of experience. Materials and Methods: Eighty-four freshmen and 32 dental graduates examined occlusal surfaces of molars/premolars (n = 72) after a lecture and a hands-on workshop. The same procedure was repeated after 1 month following the training with ICDAS II e-learning program. Validation of ICDAS II codes was done histologically. Intra- and inter-examiner reproducibility of ICDAS II severity scores were assessed before and after e-learning using (Fleiss's kappa). Results: The kappa values showed inter-examiner reproducibility ranged from 0.53 (ICDAS II code cut off ≥ 1) to 0.70 (ICDAS II code cut off ≥ 3) by undergraduates and 0.69 (ICDAS II code cut off ≥ 1) to 0.95 (ICDAS II code cut off ≥ 3) by graduates. The inter-examiner reproducibility ranged from 0.64 (ICDAS II code cut off ≥ 1) to 0.89 (ICDAS II code cut off ≥ 3). No statistically significant difference was found between both groups in intra-examiner agreements for assessing ICDAS II codes. A high statistically significant difference (P ≤ 0.01) in correct identification of codes 1, 2, and 4 from before to after e-learning were observed in both groups. The bias indices for the undergraduate group were higher than those of the graduate group. Conclusions: Early exposure of students to ICDAS II is a valuable method of teaching caries detection and its e-learning program significantly improves their caries diagnostic skills. PMID:25512730

A new measurement of electron transverse polarization in polarized nuclear β-decay

NASA Astrophysics Data System (ADS)

Kawamura, H.; Akiyama, T.; Hata, M.; Hirayama, Y.; Ikeda, M.; Ikeda, Y.; Ishii, T.; Kameda, D.; Mitsuoka, S.; Miyatake, H.; Nagae, D.; Nakaya, Y.; Ninomiya, K.; Nitta, M.; Ogawa, N.; Onishi, J.; Seitaibashi, E.; Tanaka, S.; Tanuma, R.; Totsuka, Y.; Toyoda, T.; Watanabe, Y. X.; Murata, J.

2017-03-01

The Mott polarimetry for T-violation (MTV) experiment tests time-reversal symmetry in polarized nuclear β-decay by measuring an electron’s transverse polarization as a form of angular asymmetry in Mott scattering using a thin metal foil. A Mott scattering analyzer system developed using a tracking detector to measure scattering angles offers better event selectivity than conventional counter experiments. In this paper, we describe a pilot experiment conducted at KEK-TRIAC using a prototype system with a polarized 8Li beam. The experiment confirmed the sound performance of our Mott analyzer system to measure T-violating triple correlation (R correlation), and therefore recommends its use in higher-precision experiments at the TRIUMF-ISAC.

Wall-loss distribution of charge breeding ions in an electron cyclotron resonance ion source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeong, S. C.; Oyaizu, M.; Imai, N.

2012-02-15

We investigated the ion-loss distribution on the sidewall of an electron cyclotron resonance (ECR) plasma chamber using the 18-GHz ECR charge breeder at the Tokai Radioactive Ion Accelerator Complex (TRIAC). Similarities and differences between the ion-loss distributions (longitudinal and azimuthal) of different ion species (i.e., radioactive {sup 111}In{sup 1+} and {sup 140}Xe{sup 1+} ions that are typical volatile and nonvolatile elements) was qualitatively discussed to understand the element dependence of the charge breeding efficiency. Especially, the similarities represent universal ion loss characteristics in an ECR charge breeder, which are different from the loss patterns of electrons on the ECRIS wall.

TEMPEST II--A NEUTRON THERMALIZATION CODE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shudde, R.H.; Dyer, J.

The TEMPEST II neutron thermalization code in Fortran for IBM 709 or 7090 calculates thermal neutron flux spectra based upon the Wigner-Wilkins equation, the Wilkins equation, or the Maxwellian distribution. When a neutron spectrum is obtained, TEMPEST II provides microscopic and macroscopic cross section averages over that spectrum. Equations used by the code and sample input and output data are given. (auth)

User's manual for the BNW-II optimization code for dry/wet-cooled power plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braun, D.J.; Bamberger, J.A.; Braun, D.J.

1978-05-01

This volume provides a listing of the BNW-II dry/wet ammonia heat rejection optimization code and is an appendix to Volume I which gives a narrative description of the code's algorithms as well as logic, input and output information.

COMPUTATION OF GLOBAL PHOTOCHEMISTRY WITH SMVGEAR II (R823186)

EPA Science Inventory

A computer model was developed to simulate global gas-phase photochemistry. The model solves chemical equations with SMVGEAR II, a sparse-matrix, vectorized Gear-type code. To obtain SMVGEAR II, the original SMVGEAR code was modified to allow computation of different sets of chem...

Monte Carol-based validation of neutronic methodology for EBR-II analyses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liaw, J.R.; Finck, P.J.

1993-01-01

The continuous-energy Monte Carlo code VIM (Ref. 1) has been validated extensively over the years against fast critical experiments and other neutronic analysis codes. A high degree of confidence in VIM for predicting reactor physics parameters has been firmly established. This paper presents a numerical validation of two conventional multigroup neutronic analysis codes, DIF3D (Ref. 4) and VARIANT (Ref. 5), against VIM for two Experimental Breeder Reactor II (EBR-II) core loadings in detailed three-dimensional hexagonal-z geometry. The DIF3D code is based on nodal diffusion theory, and it is used in calculations for day-today reactor operations, whereas the VARIANT code ismore » based on nodal transport theory and is used with increasing frequency for specific applications. Both DIF3D and VARIANT rely on multigroup cross sections generated from ENDF/B-V by the ETOE-2/MC[sup 2]-II/SDX (Ref. 6) code package. Hence, this study also validates the multigroup cross-section processing methodology against the continuous-energy approach used in VIM.« less

Construction of type-II QC-LDPC codes with fast encoding based on perfect cyclic difference sets

NASA Astrophysics Data System (ADS)

Li, Ling-xiang; Li, Hai-bing; Li, Ji-bi; Jiang, Hua

2017-09-01

In view of the problems that the encoding complexity of quasi-cyclic low-density parity-check (QC-LDPC) codes is high and the minimum distance is not large enough which leads to the degradation of the error-correction performance, the new irregular type-II QC-LDPC codes based on perfect cyclic difference sets (CDSs) are constructed. The parity check matrices of these type-II QC-LDPC codes consist of the zero matrices with weight of 0, the circulant permutation matrices (CPMs) with weight of 1 and the circulant matrices with weight of 2 (W2CMs). The introduction of W2CMs in parity check matrices makes it possible to achieve the larger minimum distance which can improve the error- correction performance of the codes. The Tanner graphs of these codes have no girth-4, thus they have the excellent decoding convergence characteristics. In addition, because the parity check matrices have the quasi-dual diagonal structure, the fast encoding algorithm can reduce the encoding complexity effectively. Simulation results show that the new type-II QC-LDPC codes can achieve a more excellent error-correction performance and have no error floor phenomenon over the additive white Gaussian noise (AWGN) channel with sum-product algorithm (SPA) iterative decoding.

Does cardiac catheterization laboratory activation by electrocardiography machine auto-interpretation reduce door-to-balloon time?

PubMed

Min, Mun Ki; Ryu, Ji Ho; Kim, Yong In; Park, Maeng Real; Park, Yong Myeon; Park, Sung Wook; Yeom, Seok Ran; Han, Sang Kyoon; Kim, Yang Weon

2014-11-01

In an attempt to begin ST-segment elevation myocardial infarction (STEMI) treatment more quickly (referred to as door-to-balloon [DTB] time) by minimizing preventable delays in electrocardiogram (ECG) interpretation, cardiac catheterization laboratory (CCL) activation was changed from activation by the emergency physician (code heart I) to activation by a single page if the ECG is interpreted as STEMI by the ECG machine (ECG machine auto-interpretation) (code heart II). We sought to determine the impact of ECG machine auto-interpretation on CCL activation. The study period was from June 2010 to May 2012 (from June to November 2011, code heart I; from December 2011 to May 2012, code heart II). All patients aged 18 years or older who were diagnosed with STEMI were evaluated for enrollment. Patients who experienced the code heart system were also included. Door-to-balloon time before and after code heart system were compared with a retrospective chart review. In addition, to determine the appropriateness of the activation, we compared coronary angiography performance rate and percentage of STEMI between code heart I and II. After the code heart system, the mean DTB time was significantly decreased (before, 96.51 ± 65.60 minutes; after, 65.40 ± 26.40 minutes; P = .043). The STEMI diagnosis and the coronary angiography performance rates were significantly lower in the code heart II group than in the code heart I group without difference in DTB time. Cardiac catheterization laboratory activation by ECG machine auto-interpretation does not reduce DTB time and often unnecessarily activates the code heart system compared with emergency physician-initiated activation. This system therefore decreases the appropriateness of CCL activation. Copyright © 2014 Elsevier Inc. All rights reserved.

Solid state control system for oil well bailer pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Senghaas, K. A.; Senghaas, P.

1985-05-14

A solid state switching controller for use with various types of oil well bailer pumps. Individually programmable steps with lockouts provide multiple mutual exclusivity between various circuit operations. A trickle charge battery system powers the control circuits. A tank overflow float protects against oil spillage. An automatic production rate adjustment circuit is provided which increases cycle time in proportion to the rate of production. The circuit includes a low power voltage detector for disabling the control circuits until the line voltage is acceptable. A three-phase power and control system with an isolation transformer for the controls avoids unreliable ground connections.more » The timers include a dividing circuit with an RC circuit. All power actuated apparatus are actuated by triac switches which are controlled by an opto driver. The bailer brake is pulse actuated for allowing the bailer to sink into crude oil without excess cable looseness.« less

Hyperthyroidism due to inappropriate secretion of thyroid-stimulating hormone: diagnosis and management.

PubMed

Hermus, A; Ross, H; van Liessum, P; Naber, A; Smals, A; Kloppenborg, P

1991-06-01

The case histories of three patients with hyperthyroidism due to overproduction of thyroid-stimulating hormone (TSH) by the pituitary gland are described. In the first patient treatment with the T3-metabolite 3,5,3'-triiodothyroacetic acid (TRIAC) led to complete clinical and biochemical normalization. In the second patient treatment with the dopaminergic agonist bromocriptine led to a temporal amelioration of hyperthyroidism. In the third patient, who was the only one with a proven pituitary adenoma, hypersecretion of TSH could be controlled by administration of the somatostatin analogue octreotide. It is emphasized that patients with this disorder should preferably not be treated with thyrostatic drugs, radioactive iodine or thyroid surgery. The success rate of these treatment modalities is lower than normal, they may lead to an increase of goiter size, and they potentially may promote growth or development of a TSH-producing adenoma. Treatment should be aimed at diminishing TSH hypersecretion.

The Morse code effect: A crystal-crystal transformation observed in gel-grown lead (II) oxalate crystals

NASA Astrophysics Data System (ADS)

Lisgarten, J. N.; Marks, J. A.

2018-05-01

This paper reports on an unusual crystal-crystal transformation phenomenon, which we have called the Morse Code Effect, based on the change in appearance of lead(II) oxalate crystals grown in agarose gels.

EXODUS II: A finite element data model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schoof, L.A.; Yarberry, V.R.

1994-09-01

EXODUS II is a model developed to store and retrieve data for finite element analyses. It is used for preprocessing (problem definition), postprocessing (results visualization), as well as code to code data transfer. An EXODUS II data file is a random access, machine independent, binary file that is written and read via C, C++, or Fortran library routines which comprise the Application Programming Interface (API).

Transcriptomes of six mutants in the Sen1 pathway reveal combinatorial control of transcription termination across the Saccharomyces cerevisiae genome

PubMed Central

Carver, Melissa N.; Müller, Ulrika; Bekiranov, Stefan; Auble, David T.

2017-01-01

Transcriptome studies on eukaryotic cells have revealed an unexpected abundance and diversity of noncoding RNAs synthesized by RNA polymerase II (Pol II), some of which influence the expression of protein-coding genes. Yet, much less is known about biogenesis of Pol II non-coding RNA than mRNAs. In the budding yeast Saccharomyces cerevisiae, initiation of non-coding transcripts by Pol II appears to be similar to that of mRNAs, but a distinct pathway is utilized for termination of most non-coding RNAs: the Sen1-dependent or “NNS” pathway. Here, we examine the effect on the S. cerevisiae transcriptome of conditional mutations in the genes encoding six different essential proteins that influence Sen1-dependent termination: Sen1, Nrd1, Nab3, Ssu72, Rpb11, and Hrp1. We observe surprisingly diverse effects on transcript abundance for the different proteins that cannot be explained simply by differing severity of the mutations. Rather, we infer from our results that termination of Pol II transcription of non-coding RNA genes is subject to complex combinatorial control that likely involves proteins beyond those studied here. Furthermore, we identify new targets and functions of Sen1-dependent termination, including a role in repression of meiotic genes in vegetative cells. In combination with other recent whole-genome studies on termination of non-coding RNAs, our results provide promising directions for further investigation. PMID:28665995

APOLLO II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez, R.; Mondot, J.; Stankovski, Z.

1988-11-01

APOLLO II is a new, multigroup transport code under development at the Commissariat a l'Energie Atomique. The code has a modular structure and uses sophisticated software for data structuralization, dynamic memory management, data storage, and user macrolanguage. This paper gives an overview of the main methods used in the code for (a) multidimensional collision probability calculations, (b) leakage calculations, and (c) homogenization procedures. Numerical examples are given to demonstrate the potential of the modular structure of the code and the novel multilevel flat-flux representation used in the calculation of the collision probabilities.

HYDRA-II: A hydrothermal analysis computer code: Volume 3, Verification/validation assessments

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCann, R.A.; Lowery, P.S.

1987-10-01

HYDRA-II is a hydrothermal computer code capable of three-dimensional analysis of coupled conduction, convection, and thermal radiation problems. This code is especially appropriate for simulating the steady-state performance of spent fuel storage systems. The code has been evaluated for this application for the US Department of Energy's Commercial Spent Fuel Management Program. HYDRA-II provides a finite difference solution in cartesian coordinates to the equations governing the conservation of mass, momentum, and energy. A cylindrical coordinate system may also be used to enclose the cartesian coordinate system. This exterior coordinate system is useful for modeling cylindrical cask bodies. The difference equationsmore » for conservation of momentum are enhanced by the incorporation of directional porosities and permeabilities that aid in modeling solid structures whose dimensions may be smaller than the computational mesh. The equation for conservation of energy permits modeling of orthotropic physical properties and film resistances. Several automated procedures are available to model radiation transfer within enclosures and from fuel rod to fuel rod. The documentation of HYDRA-II is presented in three separate volumes. Volume I - Equations and Numerics describes the basic differential equations, illustrates how the difference equations are formulated, and gives the solution procedures employed. Volume II - User's Manual contains code flow charts, discusses the code structure, provides detailed instructions for preparing an input file, and illustrates the operation of the code by means of a model problem. This volume, Volume III - Verification/Validation Assessments, provides a comparison between the analytical solution and the numerical simulation for problems with a known solution. This volume also documents comparisons between the results of simulations of single- and multiassembly storage systems and actual experimental data. 11 refs., 55 figs., 13 tabs.« less

Comparison of SAND-II and FERRET

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wootan, D.W.; Schmittroth, F.

1981-01-01

A comparison was made of the advantages and disadvantages of two codes, SAND-II and FERRET, for determining the neutron flux spectrum and uncertainty from experimental dosimeter measurements as anticipated in the FFTF Reactor Characterization Program. This comparison involved an examination of the methodology and the operational performance of each code. The merits of each code were identified with respect to theoretical basis, directness of method, solution uniqueness, subjective influences, and sensitivity to various input parameters.

7 CFR 4274.337 - Other regulatory requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... with the seismic provisions of one of the following model building codes or the latest edition of that...) Uniform Building Code; (ii) 1993 Building Officials and Code Administrators International, Inc. (BOCA) National Building Code; or (iii) 1992 Amendments to the Southern Building Code Congress International...

7 CFR 4274.337 - Other regulatory requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... with the seismic provisions of one of the following model building codes or the latest edition of that...) Uniform Building Code; (ii) 1993 Building Officials and Code Administrators International, Inc. (BOCA) National Building Code; or (iii) 1992 Amendments to the Southern Building Code Congress International...

7 CFR 4274.337 - Other regulatory requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... with the seismic provisions of one of the following model building codes or the latest edition of that...) Uniform Building Code; (ii) 1993 Building Officials and Code Administrators International, Inc. (BOCA) National Building Code; or (iii) 1992 Amendments to the Southern Building Code Congress International...

Functional Requirements of a Target Description System for Vulnerability Analysis

DTIC Science & Technology

1979-11-01

called GIFT .1,2 Together the COMGEOM description model and GIFT codes make up the BRL’s target description system. The significance of a target...and modifying target descriptions are described. 1 Lawrence W. Bain, Jr. and Mathew J. Reisinger, "The GIFT Code User Manual; Volume 1...34The GIFT Code User Manual; Volume II, The Output Options," unpublished draft of BRL report. II. UNDERLYING PHILOSOPHY The BRL has a computer

Implementing the UCSD PASCAL system on the MODCOMP computer. [deep space network

NASA Technical Reports Server (NTRS)

Wolfe, T.

1980-01-01

The implementation of an interactive software development system (UCSD PASCAL) on the MODCOMP computer is discussed. The development of an interpreter for the MODCOMP II and the MODCOMP IV computers, written in MODCOMP II assembly language, is described. The complete Pascal programming system was run successfully on a MODCOMP II and MODCOMP IV under both the MAX II/III and MAX IV operating systems. The source code for an 8080 microcomputer version of the interpreter was used as the design for the MODCOMP interpreter. A mapping of the functions within the 8080 interpreter into MODCOMP II assembly language was the method used to code the interpreter.

HYDRA-II: A hydrothermal analysis computer code: Volume 2, User's manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCann, R.A.; Lowery, P.S.; Lessor, D.L.

1987-09-01

HYDRA-II is a hydrothermal computer code capable of three-dimensional analysis of coupled conduction, convection, and thermal radiation problems. This code is especially appropriate for simulating the steady-state performance of spent fuel storage systems. The code has been evaluated for this application for the US Department of Energy's Commercial Spent Fuel Management Program. HYDRA-II provides a finite-difference solution in cartesian coordinates to the equations governing the conservation of mass, momentum, and energy. A cylindrical coordinate system may also be used to enclose the cartesian coordinate system. This exterior coordinate system is useful for modeling cylindrical cask bodies. The difference equations formore » conservation of momentum incorporate directional porosities and permeabilities that are available to model solid structures whose dimensions may be smaller than the computational mesh. The equation for conservation of energy permits modeling of orthotropic physical properties and film resistances. Several automated methods are available to model radiation transfer within enclosures and from fuel rod to fuel rod. The documentation of HYDRA-II is presented in three separate volumes. Volume 1 - Equations and Numerics describes the basic differential equations, illustrates how the difference equations are formulated, and gives the solution procedures employed. This volume, Volume 2 - User's Manual, contains code flow charts, discusses the code structure, provides detailed instructions for preparing an input file, and illustrates the operation of the code by means of a sample problem. The final volume, Volume 3 - Verification/Validation Assessments, provides a comparison between the analytical solution and the numerical simulation for problems with a known solution. 6 refs.« less

FISPACT-II: An Advanced Simulation System for Activation, Transmutation and Material Modelling

NASA Astrophysics Data System (ADS)

Sublet, J.-Ch.; Eastwood, J. W.; Morgan, J. G.; Gilbert, M. R.; Fleming, M.; Arter, W.

2017-01-01

Fispact-II is a code system and library database for modelling activation-transmutation processes, depletion-burn-up, time dependent inventory and radiation damage source terms caused by nuclear reactions and decays. The Fispact-II code, written in object-style Fortran, follows the evolution of material irradiated by neutrons, alphas, gammas, protons, or deuterons, and provides a wide range of derived radiological output quantities to satisfy most needs for nuclear applications. It can be used with any ENDF-compliant group library data for nuclear reactions, particle-induced and spontaneous fission yields, and radioactive decay (including but not limited to TENDL-2015, ENDF/B-VII.1, JEFF-3.2, JENDL-4.0u, CENDL-3.1 processed into fine-group-structure files, GEFY-5.2 and UKDD-16), as well as resolved and unresolved resonance range probability tables for self-shielding corrections and updated radiological hazard indices. The code has many novel features including: extension of the energy range up to 1 GeV; additional neutron physics including self-shielding effects, temperature dependence, thin and thick target yields; pathway analysis; and sensitivity and uncertainty quantification and propagation using full covariance data. The latest ENDF libraries such as TENDL encompass thousands of target isotopes. Nuclear data libraries for Fispact-II are prepared from these using processing codes PREPRO, NJOY and CALENDF. These data include resonance parameters, cross sections with covariances, probability tables in the resonance ranges, PKA spectra, kerma, dpa, gas and radionuclide production and energy-dependent fission yields, supplemented with all 27 decay types. All such data for the five most important incident particles are provided in evaluated data tables. The Fispact-II simulation software is described in detail in this paper, together with the nuclear data libraries. The Fispact-II system also includes several utility programs for code-use optimisation, visualisation and production of secondary radiological quantities. Included in the paper are summaries of results from the suite of verification and validation reports available with the code.

Computational tools and lattice design for the PEP-II B-Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Irwin, J.; Nosochkov, Y.

1997-02-01

Several accelerator codes were used to design the PEP-II lattices, ranging from matrix-based codes, such as MAD and DIMAD, to symplectic-integrator codes, such as TRACY and DESPOT. In addition to element-by-element tracking, we constructed maps to determine aberration strengths. Furthermore, we have developed a fast and reliable method (nPB tracking) to track particles with a one-turn map. This new technique allows us to evaluate performance of the lattices on the entire tune-plane. Recently, we designed and implemented an object-oriented code in C++ called LEGO which integrates and expands upon TRACY and DESPOT. {copyright} {ital 1997 American Institute of Physics.}

Computational tools and lattice design for the PEP-II B-Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai Yunhai; Irwin, John; Nosochkov, Yuri

1997-02-01

Several accelerator codes were used to design the PEP-II lattices, ranging from matrix-based codes, such as MAD and DIMAD, to symplectic-integrator codes, such as TRACY and DESPOT. In addition to element-by-element tracking, we constructed maps to determine aberration strengths. Furthermore, we have developed a fast and reliable method (nPB tracking) to track particles with a one-turn map. This new technique allows us to evaluate performance of the lattices on the entire tune-plane. Recently, we designed and implemented an object-oriented code in C++ called LEGO which integrates and expands upon TRACY and DESPOT.

Benchmark Simulations of the Thermal-Hydraulic Responses during EBR-II Inherent Safety Tests using SAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Rui; Sumner, Tyler S.

2016-04-17

An advanced system analysis tool SAM is being developed for fast-running, improved-fidelity, and whole-plant transient analyses at Argonne National Laboratory under DOE-NE’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. As an important part of code development, companion validation activities are being conducted to ensure the performance and validity of the SAM code. This paper presents the benchmark simulations of two EBR-II tests, SHRT-45R and BOP-302R, whose data are available through the support of DOE-NE’s Advanced Reactor Technology (ART) program. The code predictions of major primary coolant system parameter are compared with the test results. Additionally, the SAS4A/SASSYS-1 code simulationmore » results are also included for a code-to-code comparison.« less

Analysis of JSI TRIGA MARK II reactor physical parameters calculated with TRIPOLI and MCNP.

PubMed

Henry, R; Tiselj, I; Snoj, L

2015-03-01

New computational model of the JSI TRIGA Mark II research reactor was built for TRIPOLI computer code and compared with existing MCNP code model. The same modelling assumptions were used in order to check the differences of the mathematical models of both Monte Carlo codes. Differences between the TRIPOLI and MCNP predictions of keff were up to 100pcm. Further validation was performed with analyses of the normalized reaction rates and computations of kinetic parameters for various core configurations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Numerical Electromagnetic Code (NEC)-Reflector Antenna Code: Part II. Code Manual.

DTIC Science & Technology

1979-09-01

SI N*I~iSl NTE. L%) I 82 GO 󈧏) 242 182 1b8. 3 ZL=P3 84 [) HHO =ZL-HOS( I) b5 If- (r)RH,.L[-..21.AND.DRIIO.GF.O.) ZL=RiOS(1)-9).05 80DFHO=ZL-PHOS(2...ALPHA(2) ,X(2),Y(2),Z(2),XS(3), HHOS (2) DIMENSION MI.J(2 ),.ML(2 ),SIGN(2) I]I LOGI CAL L’f[ST, LI)E13! * 12 COMMON /RFFr)Y/fHOS I -"’ICOMMAON /FOCAL

Diabetes mellitus in a girl with thyroid hormone resistance syndrome: a little recognized interaction between the two diseases.

PubMed

Stagi, Stefano; Manoni, Cristina; Cirello, Valentina; Covelli, Danila; Giglio, Sabrina; Chiarelli, Francesco; Seminara, Salvatore; de Martino, Maurizio

2014-01-01

The syndrome of resistance to thyroid hormone (RTH) is characterized by elevated serum free thyroid hormones (FT4 and FT3) in the presence of unsuppressed TSH levels, reflecting resistance to the normal negative feedback mechanisms in the hypothalamus and pituitary. The degree of resistance within peripheral tissues determines whether thyrotoxic clinical features are associated with this condition. Classic features include attention deficit hyperactivity disorder, growth delay, tachycardia, and goiter. However, other features, such as frequent ear, nose and throat infections, hearing deficit, and decreased bone mass have recently been recognized. The phenotype of RTH is variable, with most patients presenting with mild to moderate symptoms. In this report we describe a girl with familiar RTH and diabetes mellitus. This is, to our knowledge, the first report regarding this association. Nearly one year after long-term triiodothyroacetic acid (Triac) therapy, we observed a reduction of thyroid hormone levels with an amelioration of insulin resistance. The possible interactions between these disorders are discussed.

A user`s guide to LUGSAN II. A computer program to calculate and archive lug and sway brace loads for aircraft-carried stores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunn, W.N.

1998-03-01

LUG and Sway brace ANalysis (LUGSAN) II is an analysis and database computer program that is designed to calculate store lug and sway brace loads for aircraft captive carriage. LUGSAN II combines the rigid body dynamics code, SWAY85, with a Macintosh Hypercard database to function both as an analysis and archival system. This report describes the LUGSAN II application program, which operates on the Macintosh System (Hypercard 2.2 or later) and includes function descriptions, layout examples, and sample sessions. Although this report is primarily a user`s manual, a brief overview of the LUGSAN II computer code is included with suggestedmore » resources for programmers.« less

Navier-Stokes and Comprehensive Analysis Performance Predictions of the NREL Phase VI Experiment

NASA Technical Reports Server (NTRS)

Duque, Earl P. N.; Burklund, Michael D.; Johnson, Wayne

2003-01-01

A vortex lattice code, CAMRAD II, and a Reynolds-Averaged Navier-Stoke code, OVERFLOW-D2, were used to predict the aerodynamic performance of a two-bladed horizontal axis wind turbine. All computations were compared with experimental data that was collected at the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Computations were performed for both axial as well as yawed operating conditions. Various stall delay models and dynamics stall models were used by the CAMRAD II code. Comparisons between the experimental data and computed aerodynamic loads show that the OVERFLOW-D2 code can accurately predict the power and spanwise loading of a wind turbine rotor.

Performance Analysis of Hybrid ARQ Protocols in a Slotted Code Division Multiple-Access Network

DTIC Science & Technology

1989-08-01

Convolutional Codes . in Proc Int. Conf. Commun., 21.4.1-21.4.5, 1987. [27] J. Hagenauer. Rate Compatible Punctured Convolutional Codes . in Proc Int. Conf...achieved by using a low rate (r = 0.5), high constraint length (e.g., 32) punctured convolutional code . Code puncturing provides for a variable rate code ...investigated the use of convolutional codes in Type II Hybrid ARQ protocols. The error

EUPDF-II: An Eulerian Joint Scalar Monte Carlo PDF Module : User's Manual

NASA Technical Reports Server (NTRS)

Raju, M. S.; Liu, Nan-Suey (Technical Monitor)

2004-01-01

EUPDF-II provides the solution for the species and temperature fields based on an evolution equation for PDF (Probability Density Function) and it is developed mainly for application with sprays, combustion, parallel computing, and unstructured grids. It is designed to be massively parallel and could easily be coupled with any existing gas-phase CFD and spray solvers. The solver accommodates the use of an unstructured mesh with mixed elements of either triangular, quadrilateral, and/or tetrahedral type. The manual provides the user with an understanding of the various models involved in the PDF formulation, its code structure and solution algorithm, and various other issues related to parallelization and its coupling with other solvers. The source code of EUPDF-II will be available with National Combustion Code (NCC) as a complete package.

Inertial Impact Switches for Artillery Fuzes. Part III. Rocket Application

DTIC Science & Technology

1975-04-01

INtWT.INiUUITO» iiTwar mN.coimcT Nom > i. minrtwotMutt. SLOTS IN END UP MO SCOVTOBCmUNC«ITH EMM OTMR WITHIN 10* SCCNOTC...ENGR LAB COMMANDER NAVAL SURFACE WEAPONS CENTER WHITE OAK, MD 20910 ATTN CODE 043 , PROJ MGR, FUZES ATTN CODE 511, ATTN CODE 512, ATTN CODE 522

Report number codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, R.N.

This publication lists all report number codes processed by the Office of Scientific and Technical Information. The report codes are substantially based on the American National Standards Institute, Standard Technical Report Number (STRN)-Format and Creation Z39.23-1983. The Standard Technical Report Number (STRN) provides one of the primary methods of identifying a specific technical report. The STRN consists of two parts: The report code and the sequential number. The report code identifies the issuing organization, a specific program, or a type of document. The sequential number, which is assigned in sequence by each report issuing entity, is not included in thismore » publication. Part I of this compilation is alphabetized by report codes followed by issuing installations. Part II lists the issuing organization followed by the assigned report code(s). In both Parts I and II, the names of issuing organizations appear for the most part in the form used at the time the reports were issued. However, for some of the more prolific installations which have had name changes, all entries have been merged under the current name.« less

TORO II: A finite element computer program for nonlinear quasi-static problems in electromagnetics: Part 1, Theoretical background

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gartling, D.K.

The theoretical and numerical background for the finite element computer program, TORO II, is presented in detail. TORO II is designed for the multi-dimensional analysis of nonlinear, electromagnetic field problems described by the quasi-static form of Maxwell`s equations. A general description of the boundary value problems treated by the program is presented. The finite element formulation and the associated numerical methods used in TORO II are also outlined. Instructions for the use of the code are documented in SAND96-0903; examples of problems analyzed with the code are also provided in the user`s manual. 24 refs., 8 figs.

What's New in GSAS-II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toby, Brian H.; Von Dreele, Robert B.

The General Structure and Analysis Software II (GSAS-II) package is an all-new crystallographic analysis package written to replace and extend the capabilities of the universal and widely used GSAS and EXPGUI packages. GSAS-II was described in a 2013 article, but considerable work has been completed since then. This paper describes the advances, which include: rigid body fitting and structure solution modules; improved treatment for parametric refinements and equation of state fitting; and small-angle scattering data reduction and analysis. GSAS-II offers versatile and extensible modules for import and export of data and results. Capabilities are provided for users to select anymore » version of the code. Code documentation has reached 150 pages and 17 web-tutorials are offered. © 2014 International Centre for Diffraction Data.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sublet, J.-Ch., E-mail: jean-christophe.sublet@ukaea.uk; Eastwood, J.W.; Morgan, J.G.

Fispact-II is a code system and library database for modelling activation-transmutation processes, depletion-burn-up, time dependent inventory and radiation damage source terms caused by nuclear reactions and decays. The Fispact-II code, written in object-style Fortran, follows the evolution of material irradiated by neutrons, alphas, gammas, protons, or deuterons, and provides a wide range of derived radiological output quantities to satisfy most needs for nuclear applications. It can be used with any ENDF-compliant group library data for nuclear reactions, particle-induced and spontaneous fission yields, and radioactive decay (including but not limited to TENDL-2015, ENDF/B-VII.1, JEFF-3.2, JENDL-4.0u, CENDL-3.1 processed into fine-group-structure files, GEFY-5.2more » and UKDD-16), as well as resolved and unresolved resonance range probability tables for self-shielding corrections and updated radiological hazard indices. The code has many novel features including: extension of the energy range up to 1 GeV; additional neutron physics including self-shielding effects, temperature dependence, thin and thick target yields; pathway analysis; and sensitivity and uncertainty quantification and propagation using full covariance data. The latest ENDF libraries such as TENDL encompass thousands of target isotopes. Nuclear data libraries for Fispact-II are prepared from these using processing codes PREPRO, NJOY and CALENDF. These data include resonance parameters, cross sections with covariances, probability tables in the resonance ranges, PKA spectra, kerma, dpa, gas and radionuclide production and energy-dependent fission yields, supplemented with all 27 decay types. All such data for the five most important incident particles are provided in evaluated data tables. The Fispact-II simulation software is described in detail in this paper, together with the nuclear data libraries. The Fispact-II system also includes several utility programs for code-use optimisation, visualisation and production of secondary radiological quantities. Included in the paper are summaries of results from the suite of verification and validation reports available with the code.« less

26 CFR 1.883-0 - Outline of major topics.

Code of Federal Regulations, 2011 CFR

2011-04-01

... agreement, code-sharing arrangement or other joint venture. (3) Activities not considered operation of ships or aircraft. (4) Examples. (5) Definitions. (i) Bareboat charter. (ii) Code-sharing arrangement. (iii..., partnership, strategic alliance, joint operating agreement, code-sharing arrangement or other joint venture...

26 CFR 1.883-0 - Outline of major topics.

Code of Federal Regulations, 2013 CFR

2013-04-01

... agreement, code-sharing arrangement or other joint venture. (3) Activities not considered operation of ships or aircraft. (4) Examples. (5) Definitions. (i) Bareboat charter. (ii) Code-sharing arrangement. (iii..., partnership, strategic alliance, joint operating agreement, code-sharing arrangement or other joint venture...

Genetic hotels for the standard genetic code: evolutionary analysis based upon novel three-dimensional algebraic models.

PubMed

José, Marco V; Morgado, Eberto R; Govezensky, Tzipe

2011-07-01

Herein, we rigorously develop novel 3-dimensional algebraic models called Genetic Hotels of the Standard Genetic Code (SGC). We start by considering the primeval RNA genetic code which consists of the 16 codons of type RNY (purine-any base-pyrimidine). Using simple algebraic operations, we show how the RNA code could have evolved toward the current SGC via two different intermediate evolutionary stages called Extended RNA code type I and II. By rotations or translations of the subset RNY, we arrive at the SGC via the former (type I) or via the latter (type II), respectively. Biologically, the Extended RNA code type I, consists of all codons of the type RNY plus codons obtained by considering the RNA code but in the second (NYR type) and third (YRN type) reading frames. The Extended RNA code type II, comprises all codons of the type RNY plus codons that arise from transversions of the RNA code in the first (YNY type) and third (RNR) nucleotide bases. Since the dimensions of remarkable subsets of the Genetic Hotels are not necessarily integer numbers, we also introduce the concept of algebraic fractal dimension. A general decoding function which maps each codon to its corresponding amino acid or the stop signals is also derived. The Phenotypic Hotel of amino acids is also illustrated. The proposed evolutionary paths are discussed in terms of the existing theories of the evolution of the SGC. The adoption of 3-dimensional models of the Genetic and Phenotypic Hotels will facilitate the understanding of the biological properties of the SGC.

Dental health of 6-year-old children in Alpes Maritimes, France.

PubMed

Joseph, C; Velley, A M; Pierre, A; Bourgeois, D; Muller-Bolla, M

2011-10-01

To describe the dental health status of 6-year-old children using the ICDAS-II advanced method and to evaluate the association between the known caries risk factors with the cavitated caries lesion (WHO basic method) or with both non-cavitated and cavitated caries lesion caries (ICDAS II). In this cross-sectional study, a questionnaire was used to evaluate oral health and dietary habits of children. A clinical examination and a Cario analysis test (Pierre Fabre Oral care) were performed. Logistic regression analyses were used to assess the association between caries and daily tooth-brushing, dietary habits, visible plaque and salivary factors. There were 341 children (52% female and 6.25+/-0.46 years of age) in this study. Using the ICDAS-II advanced method, 39% of the children were caries-free. This proportion was larger (67.2%) using the WHO method. In multivariate models, visible dental plaque and Streptococcus mutans count were associated with caries experience registered as ICDAS-II codes 1-6 or codes 3-6. The absence of daily tooth-brushing with fluoridated toothpaste was associated only with caries experience ICDAS-II codes 3-6. The use of WHO or ICDAS-II method changed the proportion of caries-free children but not the clinical caries risk factors associated with caries experience.

Neural representation of objects in space: a dual coding account.

PubMed Central

Humphreys, G W

1998-01-01

I present evidence on the nature of object coding in the brain and discuss the implications of this coding for models of visual selective attention. Neuropsychological studies of task-based constraints on: (i) visual neglect; and (ii) reading and counting, reveal the existence of parallel forms of spatial representation for objects: within-object representations, where elements are coded as parts of objects, and between-object representations, where elements are coded as independent objects. Aside from these spatial codes for objects, however, the coding of visual space is limited. We are extremely poor at remembering small spatial displacements across eye movements, indicating (at best) impoverished coding of spatial position per se. Also, effects of element separation on spatial extinction can be eliminated by filling the space with an occluding object, indicating that spatial effects on visual selection are moderated by object coding. Overall, there are separate limits on visual processing reflecting: (i) the competition to code parts within objects; (ii) the small number of independent objects that can be coded in parallel; and (iii) task-based selection of whether within- or between-object codes determine behaviour. Between-object coding may be linked to the dorsal visual system while parallel coding of parts within objects takes place in the ventral system, although there may additionally be some dorsal involvement either when attention must be shifted within objects or when explicit spatial coding of parts is necessary for object identification. PMID:9770227

The Mediator complex: a central integrator of transcription

PubMed Central

Allen, Benjamin L.; Taatjes, Dylan J.

2016-01-01

The RNA polymerase II (pol II) enzyme transcribes all protein-coding and most non-coding RNA genes and is globally regulated by Mediator, a large, conformationally flexible protein complex with variable subunit composition (for example, a four-subunit CDK8 module can reversibly associate). These biochemical characteristics are fundamentally important for Mediator's ability to control various processes important for transcription, including organization of chromatin architecture and regulation of pol II pre-initiation, initiation, re-initiation, pausing, and elongation. Although Mediator exists in all eukaryotes, a variety of Mediator functions appear to be specific to metazoans, indicative of more diverse regulatory requirements. PMID:25693131

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simonen, F.A.; Khaleel, M.A.

This paper describes a statistical evaluation of the through-thickness copper variation for welds in reactor pressure vessels, and reviews the historical basis for the static and arrest fracture toughness (K{sub Ic} and K{sub Ia}) equations used in the VISA-II code. Copper variability in welds is due to fabrication procedures with copper contents being randomly distributed, variable from one location to another through the thickness of the vessel. The VISA-II procedure of sampling the copper content from a statistical distribution for every 6.35- to 12.7-mm (1/4- to 1/2-in.) layer through the thickness was found to be consistent with the statistical observations.more » However, the parameters of the VISA-II distribution and statistical limits required further investigation. Copper contents at few locations through the thickness were found to exceed the 0.4% upper limit of the VISA-II code. The data also suggest that the mean copper content varies systematically through the thickness. While, the assumption of normality is not clearly supported by the available data, a statistical evaluation based on all the available data results in mean and standard deviations within the VISA-II code limits.« less

ON UPGRADING THE NUMERICS IN COMBUSTION CHEMISTRY CODES. (R824970)

EPA Science Inventory

A method of updating and reusing legacy FORTRAN codes for combustion simulations is presented using the DAEPACK software package. The procedure is demonstrated on two codes that come with the CHEMKIN-II package, CONP and SENKIN, for the constant-pressure batch reactor simulati...

48 CFR 252.227-7013 - Rights in technical data-Noncommercial items.

Code of Federal Regulations, 2011 CFR

2011-10-01

... causing a computer to perform a specific operation or series of operations. (3) Computer software means computer programs, source code, source code listings, object code listings, design details, algorithms... or will be developed exclusively with Government funds; (ii) Studies, analyses, test data, or similar...

48 CFR 252.227-7013 - Rights in technical data-Noncommercial items.

Code of Federal Regulations, 2012 CFR

2012-10-01

... causing a computer to perform a specific operation or series of operations. (3) Computer software means computer programs, source code, source code listings, object code listings, design details, algorithms... or will be developed exclusively with Government funds; (ii) Studies, analyses, test data, or similar...

48 CFR 252.227-7013 - Rights in technical data-Noncommercial items.

Code of Federal Regulations, 2014 CFR

2014-10-01

... causing a computer to perform a specific operation or series of operations. (3) Computer software means computer programs, source code, source code listings, object code listings, design details, algorithms... or will be developed exclusively with Government funds; (ii) Studies, analyses, test data, or similar...

48 CFR 252.227-7013 - Rights in technical data-Noncommercial items.

Code of Federal Regulations, 2010 CFR

2010-10-01

... causing a computer to perform a specific operation or series of operations. (3) Computer software means computer programs, source code, source code listings, object code listings, design details, algorithms... developed exclusively with Government funds; (ii) Studies, analyses, test data, or similar data produced for...

Testicular gonadotropin-releasing hormone II receptor (GnRHR-II) knockdown constitutively impairs diurnal testosterone secretion in the boar

USDA-ARS?s Scientific Manuscript database

The second mammalian GnRH isoform (GnRH-II) and its specific receptor (GnRHR-II) are highly expressed in the testis, suggesting an important role in testis biology. Gene coding errors prevent the production of GnRH-II and GnRHR-II in many species, but both genes are functional in swine. We have demo...

User's manual for the BNW-II optimization code for dry/wet-cooled power plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braun, D.J.; Bamberger, J.A.; Braun, D.J.

1978-05-01

The User's Manual describes how to operate BNW-II, a computer code developed by the Pacific Northwest Laboratory (PNL) as a part of its activities under the Department of Energy (DOE) Dry Cooling Enhancement Program. The computer program offers a comprehensive method of evaluating the cost savings potential of dry/wet-cooled heat rejection systems. Going beyond simple ''figure-of-merit'' cooling tower optimization, this method includes such items as the cost of annual replacement capacity, and the optimum split between plant scale-up and replacement capacity, as well as the purchase and operating costs of all major heat rejection components. Hence the BNW-II code ismore » a useful tool for determining potential cost savings of new dry/wet surfaces, new piping, or other components as part of an optimized system for a dry/wet-cooled plant.« less

48 CFR 252.227-7013 - Rights in technical data-Noncommercial items.

Code of Federal Regulations, 2013 CFR

2013-10-01

... causing a computer to perform a specific operation or series of operations. (3) Computer software means computer programs, source code, source code listings, object code listings, design details, algorithms... funds; (ii) Studies, analyses, test data, or similar data produced for this contract, when the study...

TORO II simulations of induction heating in ferromagnetic materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adkins, D.R.; Gartling, D.K.; Kelley, J.B.

TORO II is a finite element computer program that is used in the simulation of electric and magnetic fields. This code, which was developed at Sandia National Laboratories, has been coupled with a finite element thermal code, COYOTE II, to predict temperature profiles in inductively heated parts. The development of an effective technique to account for the nonlinear behavior of the magnetic permeability in ferromagnetic parts is one of the more difficult aspects of solving induction heating problems. In the TORO II code, nonlinear, spatially varying magnetic permeability is approximated by an effective permeability on an element-by-element basis that effectivelymore » provides the same energy deposition that is produced when the true permeability is used. This approximation has been found to give an accurate estimate of the volumetric heating distribution in the part, and predicted temperature distributions have been experimentally verified using a medium carbon steel and a 10kW industrial induction heating unit. Work on the model was funded through a Cooperative Research and Development Agreement (CRADA) between the Department of Energy and General Motors` Delphi Saginaw Steering Systems.« less

The cDNA-derived amino acid sequence of hemoglobin II from Lucina pectinata.

PubMed

Torres-Mercado, Elineth; Renta, Jessicca Y; Rodríguez, Yolanda; López-Garriga, Juan; Cadilla, Carmen L

2003-11-01

Hemoglobin II from the clam Lucina pectinata is an oxygen-reactive protein with a unique structural organization in the heme pocket involving residues Gln65 (E7), Tyr30 (B10), Phe44 (CD1), and Phe69 (E11). We employed the reverse transcriptase-polymerase chain reaction (RT-PCR) and methods to synthesize various cDNA(HbII). An initial 300-bp cDNA clone was amplified from total RNA by RT-PCR using degenerate oligonucleotides. Gene-specific primers derived from the HbII-partial cDNA sequence were used to obtain the 5' and 3' ends of the cDNA by RACE. The length of the HbII cDNA, estimated from overlapping clones, was approximately 2114 bases. Northern blot analysis revealed that the mRNA size of HbII agrees with the estimated size using cDNA data. The coding region of the full-length HbII cDNA codes for 151 amino acids. The calculated molecular weight of HbII, including the heme group and acetylated N-terminal residue, is 17,654.07 Da.

Standardizing clinical laboratory data for secondary use.

PubMed

Abhyankar, Swapna; Demner-Fushman, Dina; McDonald, Clement J

2012-08-01

Clinical databases provide a rich source of data for answering clinical research questions. However, the variables recorded in clinical data systems are often identified by local, idiosyncratic, and sometimes redundant and/or ambiguous names (or codes) rather than unique, well-organized codes from standard code systems. This reality discourages research use of such databases, because researchers must invest considerable time in cleaning up the data before they can ask their first research question. Researchers at MIT developed MIMIC-II, a nearly complete collection of clinical data about intensive care patients. Because its data are drawn from existing clinical systems, it has many of the problems described above. In collaboration with the MIT researchers, we have begun a process of cleaning up the data and mapping the variable names and codes to LOINC codes. Our first step, which we describe here, was to map all of the laboratory test observations to LOINC codes. We were able to map 87% of the unique laboratory tests that cover 94% of the total number of laboratory tests results. Of the 13% of tests that we could not map, nearly 60% were due to test names whose real meaning could not be discerned and 29% represented tests that were not yet included in the LOINC table. These results suggest that LOINC codes cover most of laboratory tests used in critical care. We have delivered this work to the MIMIC-II researchers, who have included it in their standard MIMIC-II database release so that researchers who use this database in the future will not have to do this work. Published by Elsevier Inc.

Coding of Class I and II aminoacyl-tRNA synthetases

PubMed Central

Carter, Charles W.

2018-01-01

SUMMARY The aminoacyl-tRNA synthetases and their cognate transfer RNAs translate the universal genetic code. The twenty canonical amino acids are sufficiently diverse to create a selective advantage for dividing amino acid activation between two distinct, apparently unrelated superfamilies of synthetases, Class I amino acids being generally larger and less polar, Class II amino acids smaller and more polar. Biochemical, bioinformatic, and protein engineering experiments support the hypothesis that the two Classes descended from opposite strands of the same ancestral gene. Parallel experimental deconstructions of Class I and II synthetases reveal parallel losses in catalytic proficiency at two novel modular levels—protozymes and Urzymes—associated with the evolution of catalytic activity. Bi-directional coding supports an important unification of the proteome; affords a genetic relatedness metric—middle base-pairing frequencies in sense/antisense alignments—that probes more deeply into the evolutionary history of translation than do single multiple sequence alignments; and has facilitated the analysis of hitherto unknown coding relationships in tRNA sequences. Reconstruction of native synthetases by modular thermodynamic cycles facilitated by domain engineering emphasizes the subtlety associated with achieving high specificity, shedding new light on allosteric relationships in contemporary synthetases. Synthetase Urzyme structural biology suggests that they are catalytically active molten globules, broadening the potential manifold of polypeptide catalysts accessible to primitive genetic coding and motivating revisions of the origins of catalysis. Finally, bi-directional genetic coding of some of the oldest genes in the proteome places major limitations on the likelihood that any RNA World preceded the origins of coded proteins. PMID:28828732

The Mediator complex and transcription regulation

PubMed Central

Poss, Zachary C.; Ebmeier, Christopher C.

2013-01-01

The Mediator complex is a multi-subunit assembly that appears to be required for regulating expression of most RNA polymerase II (pol II) transcripts, which include protein-coding and most non-coding RNA genes. Mediator and pol II function within the pre-initiation complex (PIC), which consists of Mediator, pol II, TFIIA, TFIIB, TFIID, TFIIE, TFIIF and TFIIH and is approximately 4.0 MDa in size. Mediator serves as a central scaffold within the PIC and helps regulate pol II activity in ways that remain poorly understood. Mediator is also generally targeted by sequence-specific, DNA-binding transcription factors (TFs) that work to control gene expression programs in response to developmental or environmental cues. At a basic level, Mediator functions by relaying signals from TFs directly to the pol II enzyme, thereby facilitating TF-dependent regulation of gene expression. Thus, Mediator is essential for converting biological inputs (communicated by TFs) to physiological responses (via changes in gene expression). In this review, we summarize an expansive body of research on the Mediator complex, with an emphasis on yeast and mammalian complexes. We focus on the basics that underlie Mediator function, such as its structure and subunit composition, and describe its broad regulatory influence on gene expression, ranging from chromatin architecture to transcription initiation and elongation, to mRNA processing. We also describe factors that influence Mediator structure and activity, including TFs, non-coding RNAs and the CDK8 module. PMID:24088064

Survey Probe Infrared Celestial Experiment (SPICE).

DTIC Science & Technology

1985-01-01

amplitude modulation (PAM) Word clock Bit clock 3.1.2.3.2 Each signal shall be buffered and short- circuit proofed and capable of delivering a signal...TABLE OF CONTENTS I Appendix A I SPICE II Electronic Test Report Appendix B VC409-OOOl Pulse Code Modulator Specification - SPICE I VC409-OOOl-21 Pulse...Code Modulator Specification - SPICE II Appendix C - Specifications AA0209-103 Evacuation AA0209-104 Cryogen Filling AA0209-105 Leak Rate AA0209-106

Exploring Accelerating Science Applications with FPGAs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Storaasli, Olaf O; Strenski, Dave

2007-01-01

FPGA hardware and tools (VHDL, Viva, MitrionC and CHiMPS) are described. FPGA performance is evaluated on two Cray XD1 systems (Virtex-II Pro 50 and Virtex-4 LX160) for human genome (DNA and protein) sequence comparisons for a computational biology code (FASTA). Scalable FPGA speedups of 50X (Virtex-II) and 100X (Virtex-4) over a 2.2 GHz Opteron were achieved. Coding and IO issues faced for human genome data are described.

Genetic and physiological relationships between L-asparaginase I and asparaginase II in Saccharomyces cerevisiae.

PubMed Central

Jones, G E

1977-01-01

The cistron that codes for L-asparaginase I in Saccharomyces cerevisiae (aspl) is not genetically linked to either of the cistrons coding for expression of asparaginase II (asp2 and asp3). Cells containing different combinations of theses enzymes grow at different rates in media in which L-asparagine or D-asparagine is the only source of nitrogen for cell replication. Cells lacking L-asparaginase I but possessing asparaginase II grow more rapidly in medium containing D-asparagine as a nitrogen source than cells containing both enzymes, even though D-asparagine is not a substrate of L-asparaginase I. These results indicate that L-asparaginase I and asparaginase II interact in some way to regulate the utilization of asparagine as a nitrogen source for cell growth. PMID:323221

A hydrodynamic approach to cosmology - Methodology

NASA Technical Reports Server (NTRS)

Cen, Renyue

1992-01-01

The present study describes an accurate and efficient hydrodynamic code for evolving self-gravitating cosmological systems. The hydrodynamic code is a flux-based mesh code originally designed for engineering hydrodynamical applications. A variety of checks were performed which indicate that the resolution of the code is a few cells, providing accuracy for integral energy quantities in the present simulations of 1-3 percent over the whole runs. Six species (H I, H II, He I, He II, He III) are tracked separately, and relevant ionization and recombination processes, as well as line and continuum heating and cooling, are computed. The background radiation field is simultaneously determined in the range 1 eV to 100 keV, allowing for absorption, emission, and cosmological effects. It is shown how the inevitable numerical inaccuracies can be estimated and to some extent overcome.

Power train and emission control: allocation procedure by OBD-II system for automotive technology

NASA Astrophysics Data System (ADS)

Kalita, Porag

2017-06-01

OBD-II, systems were designed to maintain low emissions of in use vehicles, including light and medium duty vehicles. In 1989, the California code of Regulations (CCR) known as OBD - II was adopted by the California Air Resource Board (CARB) and the objective to reduce hydrocarbon (HC) emission caused by malfunction of the vehicles emission control systems. OBD-II provides additional information to engineer for diagnosis and repair of emissions related problems. OBD-II, standardizes on the amount of memory (Freeze Frame) it uses to store the readings of the vehicle sensor when it logs on emission related Intermittent Trouble code (IT). The intent of OBD-II, systems is to detect most vehicle malfunctions when performance of a power train component or system deteriorates to the point that the vehicle’s HC emission exceed standard. The vehicle operator is notified at the time when the vehicle begins to marginally exceed emission standards, by illuminating the Malfunctions Indicator Light (MIL).

29 CFR 1910.144 - Safety color code for marking physical hazards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 5 2013-07-01 2013-07-01 false Safety color code for marking physical hazards. 1910.144... § 1910.144 Safety color code for marking physical hazards. (a) Color identification—(1) Red. Red shall be the basic color for the identification of: (i) Fire protection equipment and apparatus. [Reserved] (ii...

29 CFR 1910.144 - Safety color code for marking physical hazards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 5 2014-07-01 2014-07-01 false Safety color code for marking physical hazards. 1910.144... § 1910.144 Safety color code for marking physical hazards. (a) Color identification—(1) Red. Red shall be the basic color for the identification of: (i) Fire protection equipment and apparatus. [Reserved] (ii...

29 CFR 1910.144 - Safety color code for marking physical hazards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 5 2012-07-01 2012-07-01 false Safety color code for marking physical hazards. 1910.144... § 1910.144 Safety color code for marking physical hazards. (a) Color identification—(1) Red. Red shall be the basic color for the identification of: (i) Fire protection equipment and apparatus. [Reserved] (ii...

Agreement Between the United States Secret Service and the Department of Defense Concerning Protection of the President and Other Officials

DTIC Science & Technology

1986-09-17

States Secret Service, in accordance with the responsibilities of the Secret Service as authorized by Section 3056, Title 18, U.S. Code; and Section 202 of...Title 3, U.S. Code. II. General Responsibilities Subject to the direction of the Secretary of the Treasury, the Secret Service is authorized to... the Secret Service, other than those persons or positions specifically identified under "II General Responsibilities" in this agreement, will be

Evaluation of Assimilative SST Forecasts in the Okinawa Trough and Gulf of Mexico

DTIC Science & Technology

2012-12-06

Ruth H. Preller, 7300 Socurily, Code -- 1231 Office of 1008.3 ADOR/Director NCST E. R. Franchi , 7000 Public Affairs (Unclassified/ Unlimited Only...E. R. Franchi , 7000 Pubii<: Aifaini iiJneia5s;ii$(iF. · - Unlimited Only), Code 7030•4 0 ·-5 -J·z_...operational global ocean model GOFS 2.6. The SST level 2 data assimilated in these studies is provided by NAVOCEANO and introduced into NCODA via its OCNQC

Chimeric mitochondrial minichromosomes of the human body louse, Pediculus humanus: evidence for homologous and non-homologous recombination.

PubMed

Shao, Renfu; Barker, Stephen C

2011-02-15

The mitochondrial (mt) genome of the human body louse, Pediculus humanus, consists of 18 minichromosomes. Each minichromosome is 3 to 4 kb long and has 1 to 3 genes. There is unequivocal evidence for recombination between different mt minichromosomes in P. humanus. It is not known, however, how these minichromosomes recombine. Here, we report the discovery of eight chimeric mt minichromosomes in P. humanus. We classify these chimeric mt minichromosomes into two groups: Group I and Group II. Group I chimeric minichromosomes contain parts of two different protein-coding genes that are from different minichromosomes. The two parts of protein-coding genes in each Group I chimeric minichromosome are joined at a microhomologous nucleotide sequence; microhomologous nucleotide sequences are hallmarks of non-homologous recombination. Group II chimeric minichromosomes contain all of the genes and the non-coding regions of two different minichromosomes. The conserved sequence blocks in the non-coding regions of Group II chimeric minichromosomes resemble the "recombination repeats" in the non-coding regions of the mt genomes of higher plants. These repeats are essential to homologous recombination in higher plants. Our analyses of the nucleotide sequences of chimeric mt minichromosomes indicate both homologous and non-homologous recombination between minichromosomes in the mitochondria of the human body louse. Copyright © 2010 Elsevier B.V. All rights reserved.

Analyzing Interactions by an IIS-Map-Based Method in Face-to-Face Collaborative Learning: An Empirical Study

ERIC Educational Resources Information Center

Zheng, Lanqin; Yang, Kaicheng; Huang, Ronghuai

2012-01-01

This study proposes a new method named the IIS-map-based method for analyzing interactions in face-to-face collaborative learning settings. This analysis method is conducted in three steps: firstly, drawing an initial IIS-map according to collaborative tasks; secondly, coding and segmenting information flows into information items of IIS; thirdly,…

TACOM LCMC IB and DMSMS Mitigation

DTIC Science & Technology

2011-09-26

Sources I Gosed II Opened ~ I AAC flag: Vii6d AI CAGE codes (CONUS): 3 3 CAGE codes (OCONUS): 0 0 ---- Total: 3 3 Single or no CAGE code...v In box - I’lL- I Qi) chambers:... I ~ Microsoft - I I~ AADO SER.- t@) ~ i_ .... gose I I Used On Reference/Part Numbers I~ 26SEP11

BRD4 assists elongation of both coding and enhancer RNAs guided by histone acetylation

PubMed Central

Kanno, Tomohiko; Kanno, Yuka; LeRoy, Gary; Campos, Eric; Sun, Hong-Wei; Brooks, Stephen R; Vahedi, Golnaz; Heightman, Tom D; Garcia, Benjamin A; Reinberg, Danny; Siebenlist, Ulrich; O’Shea, John J; Ozato, Keiko

2016-01-01

Small-molecule BET inhibitors interfere with the epigenetic interactions between acetylated histones and the bromodomains of the BET family proteins, including BRD4, and they potently inhibit growth of malignant cells by targeting cancer-promoting genes. BRD4 interacts with the pause-release factor P-TEFb, and has been proposed to release Pol II from promoter-proximal pausing. We show that BRD4 occupied widespread genomic regions in mouse cells, and directly stimulated elongation of both protein-coding transcripts and non-coding enhancer RNAs (eRNAs), dependent on the function of bromodomains. BRD4 interacted physically with elongating Pol II complexes, and assisted Pol II progression through hyper-acetylated nucleosomes by interacting with acetylated histones via bromodomains. On active enhancers, the BET inhibitor JQ1 antagonized BRD4-associated eRNA synthesis. Thus, BRD4 is involved in multiple steps of the transcription hierarchy, primarily by assisting transcript elongation both at enhancers and on gene bodies. PMID:25383670

78 FR 60137 - Shipping and Transportation; Technical, Organizational, and Conforming Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-30

... INFORMATION: Table of Contents for Preamble I. Abbreviations II. Regulatory History III. Background and... States Code VCDOA Vice Commandant Decision on Appeal II. Regulatory History We did not publish a notice...

Energy information data base: report number codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1979-09-01

Each report processed by the US DOE Technical Information Center is identified by a unique report number consisting of a code plus a sequential number. In most cases, the code identifies the originating installation. In some cases, it identifies a specific program or a type of publication. Listed in this publication are all codes that have been used by DOE in cataloging reports. This compilation consists of two parts. Part I is an alphabetical listing of report codes identified with the issuing installations that have used the codes. Part II is an alphabetical listing of installations identified with codes eachmore » has used. (RWR)« less

SKYSINE-II procedure: calculation of the effects of structure design on neutron, primary gamma-ray and secondary gamma-ray dose rates in air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lampley, C.M.

1979-01-01

An updated version of the SKYSHINE Monte Carlo procedure has been developed. The new computer code, SKYSHINE-II, provides a substantial increase in versatility in that the program possesses the ability to address three types of point-isotropic radiation sources: (1) primary gamma rays, (2) neutrons, and (3) secondary gamma rays. In addition, the emitted radiation may now be characterized by an energy emission spectrum product of a new energy-dependent atmospheric transmission data base developed by Radiation Research Associates, Inc. for each of the three source types described above. Most of the computational options present in the original program have been retainedmore » in the new version. Hence, the SKYSHINE-II computer code provides a versatile and viable tool for the analysis of the radiation environment in the vicinity of a building structure containing radiation sources, situated within the confines of a nuclear power plant. This report describes many of the calculational methods employed within the SKYSHINE-II program. A brief description of the new data base is included. Utilization instructions for the program are provided for operation of the SKYSHINE-II code on the Brookhaven National Laboratory Central Scientific Computing Facility. A listing of the source decks, block data routines, and the new atmospheric transmission data base are provided in the appendices of the report.« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2007-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2007-06-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2007-09-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2006-06-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2006-01-18

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2006-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2006-12-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2007-02-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes (CH-TRUCON)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2006-09-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

CH-TRU Waste Content Codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington TRU Solutions LLC

2008-01-16

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container.more » Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments" (10-day shipping period).« less

Admiralty Inlet Advanced Turbulence Measurements: final data and code archive

DOE Data Explorer

Kilcher, Levi (ORCID:0000000183851131); Thomson, Jim (ORCID:0000000289290088); Harding, Samuel

2011-02-01

Data and code that is not already in a public location that is used in Kilcher, Thomson, Harding, and Nylund (2017) "Turbulence Measurements from Compliant Moorings - Part II: Motion Correction" doi: 10.1175/JTECH-D-16-0213.1. The links point to Python source code used in the publication. All other files are source data used in the publication.

Highly selective BSA imprinted polyacrylamide hydrogels facilitated by a metal-coding MIP approach.

PubMed

El-Sharif, H F; Yapati, H; Kalluru, S; Reddy, S M

2015-12-01

We report the fabrication of metal-coded molecularly imprinted polymers (MIPs) using hydrogel-based protein imprinting techniques. A Co(II) complex was prepared using (E)-2-((2 hydrazide-(4-vinylbenzyl)hydrazono)methyl)phenol; along with iron(III) chloroprotoporphyrin (Hemin), vinylferrocene (VFc), zinc(II) protoporphyrin (ZnPP) and protoporphyrin (PP), these complexes were introduced into the MIPs as co-monomers for metal-coding of non-metalloprotein imprints. Results indicate a 66% enhancement for bovine serum albumin (BSA) protein binding capacities (Q, mg/g) via metal-ion/ligand exchange properties within the metal-coded MIPs. Specifically, Co(II)-complex-based MIPs exhibited 92 ± 1% specific binding with Q values of 5.7 ± 0.45 mg BSA/g polymer and imprinting factors (IF) of 14.8 ± 1.9 (MIP/non-imprinted (NIP) control). The selectivity of our Co(II)-coded BSA MIPs were also tested using bovine haemoglobin (BHb), lysozyme (Lyz), and trypsin (Tryp). By evaluating imprinting factors (K), each of the latter proteins was found to have lower affinities in comparison to cognate BSA template. The hydrogels were further characterised by thermal analysis and differential scanning calorimetry (DSC) to assess optimum polymer composition. The development of hydrogel-based molecularly imprinted polymer (HydroMIPs) technology for the memory imprinting of proteins and for protein biosensor development presents many possibilities, including uses in bio-sample clean-up or selective extraction, replacement of biological antibodies in immunoassays and biosensors for medicine and the environment. Biosensors for proteins and viruses are currently expensive to develop because they require the use of expensive antibodies. Because of their biomimicry capabilities (and their potential to act as synthetic antibodies), HydroMIPs potentially offer a route to the development of new low-cost biosensors. Herein, a metal ion-mediated imprinting approach was employed to metal-code our hydrogel-based MIPs for the selective recognition of bovine serum albumin (BSA). Specifically, Co(II)-complex based MIPs exhibited a 66% enhancement (in comparison to our normal MIPs) exhibiting 92 ± 1% specific binding with Q values of 5.7 ± 0.45 mg BSA/g polymer and imprinting factors (IF) of 14.8 ± 1.9 (MIP/ non-imprinted (NIP) control). The proposed metal-coded MIPs for protein recognition are intended to lead to unprecedented improvement in MIP selectivity and for future biosensor development that rely on an electrochemical redox processes. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

RADHOT: A Radiation Hydrodynamics Code for Weapon Effects Calculation.

DTIC Science & Technology

1981-03-01

h4A ( :: [ l), t.110 )" *- 7470 -C - C... C LUMI1LTI A F ’ :: ISUfI ----- --------------- 7480= P2 GM I ’: ;,,l. II 7490C:, A ......... ’ R..E I:I ’ S...AD-AlO 637 AIR FORCE INST OF TECH WRIGHTPATTERSON AFL O SCHOOETC F /8 12/ RADHOT: A RADIATION HYDRODYNAMICS CODE FOR WEAPON EFFECTS CALCU--ETC(U...change of internal energy due to radiation atj rad F monochromatic flux V F -, F inward and outward-going monochromatic fluxes at Va cell boundary F -, F1

A Selection of Experimental Test Cases for the Validation of CFD Codes. Volume 2. (Recueil de cas d’essai Experimentaux Pour la Validation des Codes de L’Aerodynamique Numerique. Volume 2)

DTIC Science & Technology

1994-08-01

c S c o I -2 b I c 5 ^ A9-I0 Kfc 0) >% 3 .« W) o w O OJ a) 5. u > o ^a 5 ~ ^ o ra to *- w 0 " ro d) iO II...12). The technique was modified to calculate the drag %*<• 4 «.c* A12-II using ihc ncin-minjsivc LUV and sidewall pressure measure- menu rather

Numerical study of the Columbia high-beta device: Torus-II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Izzo, R.

1981-01-01

The ionization, heating and subsequent long-time-scale behavior of the helium plasma in the Columbia fusion device, Torus-II, is studied. The purpose of this work is to perform numerical simulations while maintaining a high level of interaction with experimentalists. The device is operated as a toroidal z-pinch to prepare the gas for heating. This ionization of helium is studied using a zero-dimensional, two-fluid code. It is essentially an energy balance calculation that follows the development of the various charge states of the helium and any impurities (primarily silicon and oxygen) that are present. The code is an atomic physics model ofmore » Torus-II. In addition to ionization, we include three-body and radiative recombination processes.« less

Solar Ellerman Bombs in 1D Radiative Hydrodynamics

NASA Astrophysics Data System (ADS)

Reid, A.; Mathioudakis, M.; Kowalski, A.; Doyle, J. G.; Allred, J. C.

2017-02-01

Recent observations from the Interface Region Imaging Spectrograph appear to show impulsive brightenings in high temperature lines, which when combined with simultaneous ground-based observations in Hα, appear co-spatial to Ellerman Bombs (EBs). We use the RADYN one-dimensional radiative transfer code in an attempt to try and reproduce the observed line profiles and simulate the atmospheric conditions of these events. Combined with the MULTI/RH line synthesis codes, we compute the Hα, Ca II 8542 Å, and Mg II h and k lines for these simulated events and compare them to previous observations. Our findings hint that the presence of superheated regions in the photosphere (>10,000 K) is not a plausible explanation for the production of EB signatures. While we are able to recreate EB-like line profiles in Hα, Ca II 8542 Å, and Mg II h and k, we cannot achieve agreement with all of these simultaneously.

HART-II Acoustic Predictions using a Coupled CFD/CSD Method

NASA Technical Reports Server (NTRS)

Boyd, D. Douglas, Jr.

2009-01-01

This paper documents results to date from the Rotorcraft Acoustic Characterization and Mitigation activity under the NASA Subsonic Rotary Wing Project. The primary goal of this activity is to develop a NASA rotorcraft impulsive noise prediction capability which uses first principles fluid dynamics and structural dynamics. During this effort, elastic blade motion and co-processing capabilities have been included in a recent version of the computational fluid dynamics code (CFD). The CFD code is loosely coupled to computational structural dynamics (CSD) code using new interface codes. The CFD/CSD coupled solution is then used to compute impulsive noise on a plane under the rotor using the Ffowcs Williams-Hawkings solver. This code system is then applied to a range of cases from the Higher Harmonic Aeroacoustic Rotor Test II (HART-II) experiment. For all cases presented, the full experimental configuration (i.e., rotor and wind tunnel sting mount) are used in the coupled CFD/CSD solutions. Results show good correlation between measured and predicted loading and loading time derivative at the only measured radial station. A contributing factor for a typically seen loading mean-value offset between measured data and predictions data is examined. Impulsive noise predictions on the measured microphone plane under the rotor compare favorably with measured mid-frequency noise for all cases. Flow visualization of the BL and MN cases shows that vortex structures generated in the prediction method are consist with measurements. Future application of the prediction method is discussed.

A novel TBP-TAF complex on RNA polymerase II-transcribed snRNA genes.

PubMed

Zaborowska, Justyna; Taylor, Alice; Roeder, Robert G; Murphy, Shona

2012-01-01

Initiation of transcription of most human genes transcribed by RNA polymerase II (RNAP II) requires the formation of a preinitiation complex comprising TFIIA, B, D, E, F, H and RNAP II. The general transcription factor TFIID is composed of the TATA-binding protein and up to 13 TBP-associated factors. During transcription of snRNA genes, RNAP II does not appear to make the transition to long-range productive elongation, as happens during transcription of protein-coding genes. In addition, recognition of the snRNA gene-type specific 3' box RNA processing element requires initiation from an snRNA gene promoter. These characteristics may, at least in part, be driven by factors recruited to the promoter. For example, differences in the complement of TAFs might result in differential recruitment of elongation and RNA processing factors. As precedent, it already has been shown that the promoters of some protein-coding genes do not recruit all the TAFs found in TFIID. Although TAF5 has been shown to be associated with RNAP II-transcribed snRNA genes, the full complement of TAFs associated with these genes has remained unclear. Here we show, using a ChIP and siRNA-mediated approach, that the TBP/TAF complex on snRNA genes differs from that found on protein-coding genes. Interestingly, the largest TAF, TAF1, and the core TAFs, TAF10 and TAF4, are not detected on snRNA genes. We propose that this snRNA gene-specific TAF subset plays a key role in gene type-specific control of expression.

30 CFR 204.205 - How do I obtain accounting and auditing relief?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., address, phone number, and contact name; and (ii) The specific MMS lease number and agreement number, if... contain: (i) Your company name, MMS-assigned payor code, address, phone number, and contact name; (ii) The...

Coding for Efficient Image Transmission

NASA Technical Reports Server (NTRS)

Rice, R. F.; Lee, J. J.

1986-01-01

NASA publication second in series on data-coding techniques for noiseless channels. Techniques used even in noisy channels, provided data further processed with Reed-Solomon or other error-correcting code. Techniques discussed in context of transmission of monochrome imagery from Voyager II spacecraft but applicable to other streams of data. Objective of this type coding to "compress" data; that is, to transmit using as few bits as possible by omitting as much as possible of portion of information repeated in subsequent samples (or picture elements).

Verification of MCNP simulation of neutron flux parameters at TRIGA MK II reactor of Malaysia.

PubMed

Yavar, A R; Khalafi, H; Kasesaz, Y; Sarmani, S; Yahaya, R; Wood, A K; Khoo, K S

2012-10-01

A 3-D model for 1 MW TRIGA Mark II research reactor was simulated. Neutron flux parameters were calculated using MCNP-4C code and were compared with experimental results obtained by k(0)-INAA and absolute method. The average values of φ(th),φ(epi), and φ(fast) by MCNP code were (2.19±0.03)×10(12) cm(-2)s(-1), (1.26±0.02)×10(11) cm(-2)s(-1) and (3.33±0.02)×10(10) cm(-2)s(-1), respectively. These average values were consistent with the experimental results obtained by k(0)-INAA. The findings show a good agreement between MCNP code results and experimental results. Copyright © 2012 Elsevier Ltd. All rights reserved.

Use of genetically engineered swine to elucidate testis function in the boar

USDA-ARS?s Scientific Manuscript database

The second mammalian GnRH isoform (GnRH-II) and its specific receptor (GnRHR-II) are abundant within the testis, suggesting a critical role. Gene coding errors prevent their production in many species, but both genes are functional in swine. We have demonstrated that GnRHR-II localizes to porcine Le...

On the Evolution of the Standard Genetic Code: Vestiges of Critical Scale Invariance from the RNA World in Current Prokaryote Genomes

PubMed Central

José, Marco V.; Govezensky, Tzipe; García, José A.; Bobadilla, Juan R.

2009-01-01

Herein two genetic codes from which the primeval RNA code could have originated the standard genetic code (SGC) are derived. One of them, called extended RNA code type I, consists of all codons of the type RNY (purine-any base-pyrimidine) plus codons obtained by considering the RNA code but in the second (NYR type) and third (YRN type) reading frames. The extended RNA code type II, comprises all codons of the type RNY plus codons that arise from transversions of the RNA code in the first (YNY type) and third (RNR) nucleotide bases. In order to test if putative nucleotide sequences in the RNA World and in both extended RNA codes, share the same scaling and statistical properties to those encountered in current prokaryotes, we used the genomes of four Eubacteria and three Archaeas. For each prokaryote, we obtained their respective genomes obeying the RNA code or the extended RNA codes types I and II. In each case, we estimated the scaling properties of triplet sequences via a renormalization group approach, and we calculated the frequency distributions of distances for each codon. Remarkably, the scaling properties of the distance series of some codons from the RNA code and most codons from both extended RNA codes turned out to be identical or very close to the scaling properties of codons of the SGC. To test for the robustness of these results, we show, via computer simulation experiments, that random mutations of current genomes, at the rates of 10−10 per site per year during three billions of years, were not enough for destroying the observed patterns. Therefore, we conclude that most current prokaryotes may still contain relics of the primeval RNA World and that both extended RNA codes may well represent two plausible evolutionary paths between the RNA code and the current SGC. PMID:19183813

15 CFR 740.7 - Computers (APP).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 4A003. (2) Technology and software. License Exception APP authorizes exports of technology and software... programmability. (ii) Technology and source code. Technology and source code eligible for License Exception APP..., reexports and transfers (in-country) for nuclear, chemical, biological, or missile end-users and end-uses...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2012 CFR

2012-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2014 CFR

2014-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2011 CFR

2011-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2013 CFR

2013-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2010 CFR

2010-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

76 FR 42733 - Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-19

... hearings, as follows: Thursday, July 28, 2011: 10 a.m. Claim No. LIB-II-125, Claim No. LIB-II-126 and Claim... H. Lock, Executive Officer. [FR Doc. 2011-18198 Filed 7-15-11; 11:15 am] BILLING CODE 4410-BA-P ...

Euglena gracilis chloroplast DNA: analysis of a 1.6 kb intron of the psb C gene containing an open reading frame of 458 codons.

PubMed

Montandon, P E; Vasserot, A; Stutz, E

1986-01-01

We retrieved a 1.6 kbp intron separating two exons of the psb C gene which codes for the 44 kDa reaction center protein of photosystem II. This intron is 3 to 4 times the size of all previously sequenced Euglena gracilis chloroplast introns. It contains an open reading frame of 458 codons potentially coding for a basic protein of 54 kDa of yet unknown function. The intron boundaries follow consensus sequences established for chloroplast introns related to class II and nuclear pre-mRNA introns. Its 3'-terminal segment has structural features similar to class II mitochondrial introns with an invariant base A as possible branch point for lariat formation.

High-Energy Activation Simulation Coupling TENDL and SPACS with FISPACT-II

NASA Astrophysics Data System (ADS)

Fleming, Michael; Sublet, Jean-Christophe; Gilbert, Mark

2018-06-01

To address the needs of activation-transmutation simulation in incident-particle fields with energies above a few hundred MeV, the FISPACT-II code has been extended to splice TENDL standard ENDF-6 nuclear data with extended nuclear data forms. The JENDL-2007/HE and HEAD-2009 libraries were processed for FISPACT-II and used to demonstrate the capabilities of the new code version. Tests of the libraries and comparisons against both experimental yield data and the most recent intra-nuclear cascade model results demonstrate that there is need for improved nuclear data libraries up to and above 1 GeV. Simulations on lead targets show that important radionuclides, such as 148Gd, can vary by more than an order of magnitude where more advanced models find agreement within the experimental uncertainties.

Examining the Role of Orthographic Coding Ability in Elementary Students with Previously Identified Reading Disability, Speech or Language Impairment, or Comorbid Language and Learning Disabilities

ERIC Educational Resources Information Center

Haugh, Erin Kathleen

2017-01-01

The purpose of this study was to examine the role orthographic coding might play in distinguishing between membership in groups of language-based disability types. The sample consisted of 36 second and third-grade subjects who were administered the PAL-II Receptive Coding and Word Choice Accuracy subtest as a measure of orthographic coding…

HART-II: Prediction of Blade-Vortex Interaction Loading

DTIC Science & Technology

2003-09-01

14:30 (2) Improvement of DLR Rotor Aero- acoustic Code ( APSIM ) and its Valida- tion with Analytic Solution J. Yin, J. Delfs (5...of DLR Rotor Aero- acoustic Code ( APSIM ) and its Valida- tion with Analytic Solution J. Yin, J. Delfs (5) Aeroelastic Stability Analysis of...of DLR Rotor Aero- acoustic Code ( APSIM ) and its Valida- tion with Analytic Solution J. Yin, J. Delfs (5) Aeroelastic Stability Analysis of

15 CFR 740.7 - Computers (APP).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 4A003. (2) Technology and software. License Exception APP authorizes exports of technology and software... License Exception. (2) Access and release restrictions. (i)[Reserved] (ii) Technology and source code. Technology and source code eligible for License Exception APP may not be released to nationals of Cuba, Iran...

77 FR 59768 - Shipping and Transportation; Technical, Organizational, and Conforming Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

.... Abbreviations II. Regulatory History III. Basis and Purpose IV. Background V. Regulatory Analyses A. Regulatory....S.C. United States Code II. Regulatory History We did not publish a notice of proposed rulemaking... its place, the text ``(CG-ENG)''. [[Page 59778

Joint design of QC-LDPC codes for coded cooperation system with joint iterative decoding

NASA Astrophysics Data System (ADS)

Zhang, Shunwai; Yang, Fengfan; Tang, Lei; Ejaz, Saqib; Luo, Lin; Maharaj, B. T.

2016-03-01

In this paper, we investigate joint design of quasi-cyclic low-density-parity-check (QC-LDPC) codes for coded cooperation system with joint iterative decoding in the destination. First, QC-LDPC codes based on the base matrix and exponent matrix are introduced, and then we describe two types of girth-4 cycles in QC-LDPC codes employed by the source and relay. In the equivalent parity-check matrix corresponding to the jointly designed QC-LDPC codes employed by the source and relay, all girth-4 cycles including both type I and type II are cancelled. Theoretical analysis and numerical simulations show that the jointly designed QC-LDPC coded cooperation well combines cooperation gain and channel coding gain, and outperforms the coded non-cooperation under the same conditions. Furthermore, the bit error rate performance of the coded cooperation employing jointly designed QC-LDPC codes is better than those of random LDPC codes and separately designed QC-LDPC codes over AWGN channels.

EASY-II Renaissance: n, p, d, α, γ-induced Inventory Code System

NASA Astrophysics Data System (ADS)

Sublet, J.-Ch.; Eastwood, J. W.; Morgan, J. G.

2014-04-01

The European Activation SYstem has been re-engineered and re-written in modern programming languages so as to answer today's and tomorrow's needs in terms of activation, transmutation, depletion, decay and processing of radioactive materials. The new FISPACT-II inventory code development project has allowed us to embed many more features in terms of energy range: up to GeV; incident particles: alpha, gamma, proton, deuteron and neutron; and neutron physics: self-shielding effects, temperature dependence and covariance, so as to cover all anticipated application needs: nuclear fission and fusion, accelerator physics, isotope production, stockpile and fuel cycle stewardship, materials characterization and life, and storage cycle management. In parallel, the maturity of modern, truly general purpose libraries encompassing thousands of target isotopes such as TENDL-2012, the evolution of the ENDF-6 format and the capabilities of the latest generation of processing codes PREPRO, NJOY and CALENDF have allowed the activation code to be fed with more robust, complete and appropriate data: cross sections with covariance, probability tables in the resonance ranges, kerma, dpa, gas and radionuclide production and 24 decay types. All such data for the five most important incident particles (n, p, d, α, γ), are placed in evaluated data files up to an incident energy of 200 MeV. The resulting code system, EASY-II is designed as a functional replacement for the previous European Activation System, EASY-2010. It includes many new features and enhancements, but also benefits already from the feedback from extensive validation and verification activities performed with its predecessor.

Comprehensive Analysis Modeling of Small-Scale UAS Rotors

NASA Technical Reports Server (NTRS)

Russell, Carl R.; Sekula, Martin K.

2017-01-01

Multicopter unmanned aircraft systems (UAS), or drones, have continued their explosive growth in recent years. With this growth comes demand for increased performance as the limits of existing technologies are reached. In order to better design multicopter UAS aircraft, better performance prediction tools are needed. This paper presents the results of a study aimed at using the rotorcraft comprehensive analysis code CAMRAD II to model a multicopter UAS rotor in hover. Parametric studies were performed to determine the level of fidelity needed in the analysis code inputs to achieve results that match test data. Overall, the results show that CAMRAD II is well suited to model small-scale UAS rotors in hover. This paper presents the results of the parametric studies as well as recommendations for the application of comprehensive analysis codes to multicopter UAS rotors.

Entropy Production during Fatigue as a Criterion for Failure. The Critical Entropy Threshold: A Mathematical Model for Fatigue.

DTIC Science & Technology

1983-08-15

Measurement of Material Damping," Experimental Mechanics, 297-302 (Aug 1977). 4. Feltner, C. E., and J. D. Morrow, " Microplastic Strain Hysteresis Energy as...Code OOKB, CP5, Room 606 Washington, DC 20360 Mr. Richard R. Graham, II Code 5243, Bldg. NC4 Naval Sea Systems Command "* Washington, DC 20362 Mr. Al...Harbage, Jr. Code 2723 DTNSRDC Annapolis, MD 21402 L’r. Martih Kandl Code 5231 Naval Sea Systems Command *i Washington, DC 20362 S. Karpe David W

The foundation of the Melbourne Code Appendices: Announcing a new paradigm for tracking nomenclatural decisions

USDA-ARS?s Scientific Manuscript database

A new expanded digital resource exists for tracking decisions on all nomenclature proposals potentially contributing to Appendices II-VIII of the International Code of Nomenclature. This system owes its origins to the Smithsonian Institution's Proposals and Disposals website created by Dan Nicolson ...

75 FR 6769 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-10

... To Amend the Hearing Location Rules of the Codes of Arbitration Procedure for Customer and Industry... expand the criteria for selecting a hearing location for an arbitration proceeding. The proposed rule..., 2010. II. Description of the Proposed Rule Change Hearing Location Selection Under the Customer Code...

29 CFR 1910.144 - Safety color code for marking physical hazards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the basic color for the identification of: (i) Fire protection equipment and apparatus. [Reserved] (ii... 29 Labor 5 2011-07-01 2011-07-01 false Safety color code for marking physical hazards. 1910.144 Section 1910.144 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH...

Influence of Drilling Parameters on Torque during Drilling of GFRP Composites Using Response Surface Methodology

NASA Astrophysics Data System (ADS)

Mohan, N. S.; Kulkarni, S. M.

2018-01-01

Polymer based composites have marked their valuable presence in the area of aerospace, defense and automotive industry. Components made of composite, are assembled to main structure by fastener, which require accurate, precise high quality holes to be drilled. Drilling the hole in composite with accuracy require control over various processes parameters viz., speed, feed, drill bit size and thickens of specimen. TRIAC VMC machining center is used to drill the hole and to relate the cutting and machining parameters on the torque. MINITAB 14 software is used to analyze the collected data. As a function of cutting and specimen parameters this method could be useful for predicting torque parameters. The purpose of this work is to investigate the effect of drilling parameters to get low torque value. Results show that thickness of specimen and drill bit size are significant parameters influencing the torque and spindle speed and feed rate have least influence and overlaid plot indicates a feasible and low region of torque is observed for medium to large sized drill bits for the range of spindle speed selected. Response surface contour plots indicate the sensitivity of the drill size and specimen thickness to the torque.

Cloning and expression of colonization factor antigen I (CFA/I) epitopes of enterotoxigenic Escherichia coli (ETEC) in Salmonella flagellin.

PubMed

Luna, M G; Martins, M M; Newton, S M; Costa, S O; Almeida, D F; Ferreira, L C

1997-01-01

Oligonucleotides coding for linear epitopes of the fimbrial colonization factor antigen I (CFA/I) of enterotoxigenic Escherichia coli (ETEC) were cloned and expressed in a deleted form of the Salmonella muenchen flagellin fliC (H1-d) gene. Four synthetic oligonucleotide pairs coding for regions corresponding to amino acids 1 to 15 (region I), amino acids 11 to 25 (region II), amino acids 32 to 45 (region III) and amino acids 88 to 102 (region IV) were synthesized and cloned in the Salmonella flagellin-coding gene. All four hybrid flagellins were exported to the bacterial surface where they produced flagella, but only three constructs were fully motile. Sera recovered from mice immunized with intraperitoneal injections of purified flagella containing region II (FlaII) or region IV (FlaIV) showed high titres against dissociated solid-phase-bound CFA/I subunits. Hybrid flagellins containing region I (FlaI) or region III (FlaIII) elicited a weak immune response as measured in enzyme-linked immunosorbent assay (ELISA) with dissociated CFA/I subunits. None of the sera prepared with purified hybrid flagella were able to agglutinate or inhibit haemagglutination promoted by CFA/I-positive strains. Moreover, inhibition ELISA tests indicated that antisera directed against region I, II, III or IV cloned in flagellin were not able to recognize surface-exposed regions on the intact CFA/I fimbriae.

Collaborative Simulation Grid: Multiscale Quantum-Mechanical/Classical Atomistic Simulations on Distributed PC Clusters in the US and Japan

NASA Technical Reports Server (NTRS)

Kikuchi, Hideaki; Kalia, Rajiv; Nakano, Aiichiro; Vashishta, Priya; Iyetomi, Hiroshi; Ogata, Shuji; Kouno, Takahisa; Shimojo, Fuyuki; Tsuruta, Kanji; Saini, Subhash;

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gharibyan, N.

In order to fully characterize the NIF neutron spectrum, SAND-II-SNL software was requested/received from the Radiation Safety Information Computational Center. The software is designed to determine the neutron energy spectrum through analysis of experimental activation data. However, given that the source code was developed in Sparcstation 10, it is not compatible with current version of FORTRAN. Accounts have been established through the Lawrence Livermore National Laboratory’s High Performance Computing in order to access different compiles for FORTRAN (e.g. pgf77, pgf90). Additionally, several of the subroutines included in the SAND-II-SNL package have required debugging efforts to allow for proper compiling ofmore » the code.« less

New techniques for modeling the reliability of reactor pressure vessels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, K.I.; Simonen, F.A.; Liebetrau, A.M.

1985-12-01

In recent years several probabilistic fracture mechanics codes, including the VISA code, have been developed to predict the reliability of reactor pressure vessels. This paper describes new modeling techniques used in a second generation of the VISA code entitled VISA-II. Results are presented that show the sensitivity of vessel reliability predictions to such factors as inservice inspection to detect flaws, random positioning of flaws within the vessel walls thickness, and fluence distributions that vary through-out the vessel. The algorithms used to implement these modeling techniques are also described. Other new options in VISA-II are also described in this paper. Themore » effect of vessel cladding has been included in the heat transfer, stress, and fracture mechanics solutions in VISA-II. The algorithm for simulating flaws has been changed to consider an entire vessel rather than a single flaw in a single weld. The flaw distribution was changed to include the distribution of both flaw depth and length. A menu of several alternate equations has been included to predict the shift in RTNDT. For flaws that arrest and later re-initiate, an option was also included to allow correlating the current arrest thoughness with subsequent initiation toughnesses. 21 refs.« less

The Melbourne Code Appendices: announcing a new approach for tracking nomenclatural decisions and a analysis of the history of nomenclatural proposals

USDA-ARS?s Scientific Manuscript database

A newly expanded digital resource exists for tracking decisions on all nomenclature proposals potentially contributing to Appendices II-VIII of the International Code of Nomenclature for algae, fungi, and plants. This resource originated with the Smithsonian Institution's Proposals and Disposals web...

30 CFR 1204.205 - How do I obtain accounting and auditing relief?

Code of Federal Regulations, 2012 CFR

2012-07-01

... code, address, phone number, and contact name; and (ii) The specific ONRR lease number and agreement number, if applicable. (2) You may file a single notification for multiple marginal properties. (b) To... request must contain: (i) Your company name, ONRR-assigned payor code, address, phone number, and contact...

30 CFR 1204.205 - How do I obtain accounting and auditing relief?

Code of Federal Regulations, 2014 CFR

2014-07-01

... code, address, phone number, and contact name; and (ii) The specific ONRR lease number and agreement number, if applicable. (2) You may file a single notification for multiple marginal properties. (b) To... request must contain: (i) Your company name, ONRR-assigned payor code, address, phone number, and contact...

30 CFR 1204.205 - How do I obtain accounting and auditing relief?

Code of Federal Regulations, 2011 CFR

2011-07-01

..., ONRR-assigned payor code, address, phone number, and contact name; and (ii) The specific ONRR lease number and agreement number, if applicable. (2) You may file a single notification for multiple marginal.... (1) Your request must contain: (i) Your company name, ONRR-assigned payor code, address, phone number...

30 CFR 1204.205 - How do I obtain accounting and auditing relief?

Code of Federal Regulations, 2013 CFR

2013-07-01

... code, address, phone number, and contact name; and (ii) The specific ONRR lease number and agreement number, if applicable. (2) You may file a single notification for multiple marginal properties. (b) To... request must contain: (i) Your company name, ONRR-assigned payor code, address, phone number, and contact...

7 CFR 1755.200 - RUS standard for splicing copper and fiber optic cables.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Color coded plastic tie wraps shall be placed loosely around each binder group of cables before splicing... conform to the same color designations as the binder ribbons. Twisted wire pigtails shall not be used to identify binder groups due to potential transmission degradation. (ii) The standard insulation color code...

Burnup calculations and chemical analysis of irradiated fuel samples studied in LWR-PROTEUS phase II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grimm, P.; Guenther-Leopold, I.; Berger, H. D.

2006-07-01

The isotopic compositions of 5 UO{sub 2} samples irradiated in a Swiss PWR power plant, which were investigated in the LWR-PROTEUS Phase II programme, were calculated using the CASMO-4 and BOXER assembly codes. The burnups of the samples range from 50 to 90 MWd/kg. The results for a large number of actinide and fission product nuclides were compared to those of chemical analyses performed using a combination of chromatographic separation and mass spectrometry. A good agreement of calculated and measured concentrations is found for many of the nuclides investigated with both codes. The concentrations of the Pu isotopes are mostlymore » predicted within {+-}10%, the two codes giving quite different results, except for {sup 242}Pu. Relatively significant deviations are found for some isotopes of Cs and Sm, and large discrepancies are observed for Eu and Gd. The overall quality of the predictions by the two codes is comparable, and the deviations from the experimental data do not generally increase with burnup. (authors)« less

A unified model of the standard genetic code.

PubMed

José, Marco V; Zamudio, Gabriel S; Morgado, Eberto R

2017-03-01

The Rodin-Ohno (RO) and the Delarue models divide the table of the genetic code into two classes of aminoacyl-tRNA synthetases (aaRSs I and II) with recognition from the minor or major groove sides of the tRNA acceptor stem, respectively. These models are asymmetric but they are biologically meaningful. On the other hand, the standard genetic code (SGC) can be derived from the primeval RNY code (R stands for purines, Y for pyrimidines and N any of them). In this work, the RO-model is derived by means of group actions, namely, symmetries represented by automorphisms, assuming that the SGC originated from a primeval RNY code. It turns out that the RO-model is symmetric in a six-dimensional (6D) hypercube. Conversely, using the same automorphisms, we show that the RO-model can lead to the SGC. In addition, the asymmetric Delarue model becomes symmetric by means of quotient group operations. We formulate isometric functions that convert the class aaRS I into the class aaRS II and vice versa. We show that the four polar requirement categories display a symmetrical arrangement in our 6D hypercube. Altogether these results cannot be attained, neither in two nor in three dimensions. We discuss the present unified 6D algebraic model, which is compatible with both the SGC (based upon the primeval RNY code) and the RO-model.

42 CFR 483.70 - Physical environment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... any changes in this edition of the Code are incorporated by reference, CMS will publish notice in the Federal Register to announce the changes. (ii) Chapter 19.3.6.3.2, exception number 2 of the adopted... resident; (ii) A clean, comfortable mattress; (iii) Bedding appropriate to the weather and climate; and (iv...

78 FR 28020 - Proposed Collection: Comment Request for Form 2032

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-13

... 2032, Contract Coverage Under Title II of the Social Security Act. DATES: Written comments should be... . SUPPLEMENTARY INFORMATION: Title: Contract Coverage Under Title II of the Social Security Act. OMB Number: 1545... affiliates of American employers are exempt from social security taxes. Under Internal Revenue Code section...

75 FR 52790 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-27

... for GEN II and GEN III Image Intensifier Tubes. SUMMARY: The U.S. Small Business Administration (SBA... Image Intensifier Tubes, Product Service Code (PSC) 5855, Night Vision Equipment, Emitted and Reflected... business GEN II and GEN III image intensifier tube manufacturers. If granted, the waiver would allow...

A Scalable Architecture of a Structured LDPC Decoder

NASA Technical Reports Server (NTRS)

Lee, Jason Kwok-San; Lee, Benjamin; Thorpe, Jeremy; Andrews, Kenneth; Dolinar, Sam; Hamkins, Jon

2004-01-01

We present a scalable decoding architecture for a certain class of structured LDPC codes. The codes are designed using a small (n,r) protograph that is replicated Z times to produce a decoding graph for a (Z x n, Z x r) code. Using this architecture, we have implemented a decoder for a (4096,2048) LDPC code on a Xilinx Virtex-II 2000 FPGA, and achieved decoding speeds of 31 Mbps with 10 fixed iterations. The implemented message-passing algorithm uses an optimized 3-bit non-uniform quantizer that operates with 0.2dB implementation loss relative to a floating point decoder.

Next-Generation Sequencing of Protein-Coding and Long Non-protein-Coding RNAs in Two Types of Exosomes Derived from Human Whole Saliva.

PubMed

Ogawa, Yuko; Tsujimoto, Masafumi; Yanoshita, Ryohei

2016-01-01

Exosomes are small extracellular vesicles containing microRNAs and mRNAs that are produced by various types of cells. We previously used ultrafiltration and size-exclusion chromatography to isolate two types of human salivary exosomes (exosomes I, II) that are different in size and proteomes. We showed that salivary exosomes contain large repertoires of small RNAs. However, precise information regarding long RNAs in salivary exosomes has not been fully determined. In this study, we investigated the compositions of protein-coding RNAs (pcRNAs) and long non-protein-coding RNAs (lncRNAs) of exosome I, exosome II and whole saliva (WS) by next-generation sequencing technology. Although 11% of all RNAs were commonly detected among the three samples, the compositions of reads mapping to known RNAs were similar. The most abundant pcRNA is ribosomal RNA protein, and pcRNAs of some salivary proteins such as S100 calcium-binding protein A8 (protein S100-A8) were present in salivary exosomes. Interestingly, lncRNAs of pseudogenes (presumably, processed pseudogenes) were abundant in exosome I, exosome II and WS. Translationally controlled tumor protein gene, which plays an important role in cell proliferation, cell death and immune responses, was highly expressed as pcRNA and pseudogenes in salivary exosomes. Our results show that salivary exosomes contain various types of RNAs such as pseudogenes and small RNAs, and may mediate intercellular communication by transferring these RNAs to target cells as gene expression regulators.

Microprocessor mediates transcriptional termination in long noncoding microRNA genes

PubMed Central

Dhir, Ashish; Dhir, Somdutta; Proudfoot, Nick J.; Jopling, Catherine L.

2015-01-01

MicroRNA (miRNA) play a major role in the post-transcriptional regulation of gene expression. Mammalian miRNA biogenesis begins with co-transcriptional cleavage of RNA polymerase II (Pol II) transcripts by the Microprocessor complex. While most miRNA are located within introns of protein coding genes, a substantial minority of miRNA originate from long non coding (lnc) RNA where transcript processing is largely uncharacterized. We show, by detailed characterization of liver-specific lnc-pri-miR-122 and genome-wide analysis in human cell lines, that most lnc-pri-miRNA do not use the canonical cleavage and polyadenylation (CPA) pathway, but instead use Microprocessor cleavage to terminate transcription. This Microprocessor inactivation leads to extensive transcriptional readthrough of lnc-pri-miRNA and transcriptional interference with downstream genes. Consequently we define a novel RNase III-mediated, polyadenylation-independent mechanism of Pol II transcription termination in mammalian cells. PMID:25730776

Acceleration of block-matching algorithms using a custom instruction-based paradigm on a Nios II microprocessor

NASA Astrophysics Data System (ADS)

González, Diego; Botella, Guillermo; García, Carlos; Prieto, Manuel; Tirado, Francisco

2013-12-01

This contribution focuses on the optimization of matching-based motion estimation algorithms widely used for video coding standards using an Altera custom instruction-based paradigm and a combination of synchronous dynamic random access memory (SDRAM) with on-chip memory in Nios II processors. A complete profile of the algorithms is achieved before the optimization, which locates code leaks, and afterward, creates a custom instruction set, which is then added to the specific design, enhancing the original system. As well, every possible memory combination between on-chip memory and SDRAM has been tested to achieve the best performance. The final throughput of the complete designs are shown. This manuscript outlines a low-cost system, mapped using very large scale integration technology, which accelerates software algorithms by converting them into custom hardware logic blocks and showing the best combination between on-chip memory and SDRAM for the Nios II processor.

Analyses in Support of Risk-Informed Natural Gas Vehicle Maintenance Facility Codes and Standards: Phase II.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blaylock, Myra L.; LaFleur, Chris Bensdotter; Muna, Alice Baca

Safety standards development for maintenance facilities of liquid and compressed natural gas fueled vehicles is required to ensure proper facility design and operating procedures. Standard development organizations are utilizing risk-informed concepts to develop natural gas vehicle (NGV) codes and standards so that maintenance facilities meet acceptable risk levels. The present report summarizes Phase II work for existing NGV repair facility code requirements and highlights inconsistencies that need quantitative analysis into their effectiveness. A Hazardous and Operability study was performed to identify key scenarios of interest using risk ranking. Detailed simulations and modeling were performed to estimate the location and behaviormore » of natural gas releases based on these scenarios. Specific code conflicts were identified, and ineffective code requirements were highlighted and resolutions proposed. These include ventilation rate basis on area or volume, as well as a ceiling offset which seems ineffective at protecting against flammable gas concentrations. ACKNOWLEDGEMENTS The authors gratefully acknowledge Bill Houf (SNL -- Retired) for his assistance with the set-up and post-processing of the numerical simulations. The authors also acknowledge Doug Horne (retired) for his helpful discussions. We would also like to acknowledge the support from the Clean Cities program of DOE's Vehicle Technology Office.« less

Computer Aided Design of Polyhedron Solids to Model Air in Com-Geom Descriptions

DTIC Science & Technology

1983-08-01

34The GIFT Code User Manual, Volume I, Introduction and Input Requirements," BRL Report No. 1802, July 1975 (Unclassified). (AD B0060Z7LK 2G...Kuehl, L. Bain and M. Reisinger, "The GIFT Code User Manual, Volume II, The Output Options," BRL Report ARBRL-TR-02189, September 1979...is generated from the GIFT code under op- tion XSECT. This option produces plot files which define cross- sectional views of the COM-GEOM

Logistics Support Analysis Techniques Guide

DTIC Science & Technology

1985-03-15

LANGUAGE (DATA RECORDS) FORTRAN CDC 6600 D&V FSD P/D A H REMA-RKS: Program n-s-ists of F PLIATIffIONS, approx 4000 line of coding , 3 Safegard, AN/FSC... FORTRAN IV -EW-RAK9-- The model consz.sts of IT--k-LIC- I-U-0NS: approximately 367 lines of SiNCGARS, PERSHING II coding . %.’. ~ LSA TASK INTERFACE...system supported by Computer’ Systems Command. The current version of LADEN is coded totally in FORTRAN 󈧕 for virtual memory operating system

Real-Time Parallel Software Design Case Study: Implementation of the RASSP SAR Benchmark on the Intel Paragon.

DTIC Science & Technology

1996-01-01

Real-Time 19 5 Conclusion 23 List of References 25 ii LIST OF FIGURES FIGURE PAGE 3-1 Test Bench Pseudo Code 7 3-2 Fast Convolution...3-1 shows pseudo - code for a test bench with two application nodes. The outer test bench wrapper consists of three functions: pipeline_init, pipeline...exit_func); Figure 3-1. Test Bench Pseudo Code The application wrapper is contained in the pipeline routine and similarly consists of an

Aero-Optics Code Development: Experimental Databases and AVUS Code Improvements

DTIC Science & Technology

2009-03-01

direction, helped predict accurate Strouhal number. 62 5. References [1] Siegenthaler, J., Gordeyev , S., and Jumper , E., “Shear Layers and Aperture...approach . . . . . . . . . . . . . . . . . 44 55 Grid used for the transonic flow past NACA0012 airfoil . . . . . . . . . . . . . . . . . . . . . 46 56...layer problem (Configuration II) . . . . . . . . . . . . . . . . 60 vi Acknowledgements The author would like to acknowledge Drs. Eric Jumper and

International Code of Nomenclature for Algae, Fungi, and Plants (Melbourne Code): Appendices II-VIII

USDA-ARS?s Scientific Manuscript database

Science requires a precise, stable, and simple system of nomenclature used by scientists in all countries of the world, dealing on the one hand with the terms that denote the ranks of taxonomic groups, and on the other with the scientific names that are applied to the individual taxonomic units of a...

STUDYING THE EFFECTS OF CALCIUM AND MAGNESIUM ON SIZE-DISTRIBUTED NITRATE AND AMMONIUM WITH EQUISOLV II. (R823186)

EPA Science Inventory

Abstract

A chemical equilibrium code was improved and used to show that calcium and magnesium have a large yet different effect on the aerosol size distribution in different regions of Los Angeles. In the code, a new technique of solving individual equilibrium equation...

Comment II on ''Dense coding in entangled states''

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akhavan, O.; Institute for Studies in Theoretical Physics and Mathematics; Rezakhani, A. T.

2003-07-01

In a recent Brief Report, L. Lee, D. Ahn, and S. W. Hwang [Phys. Rev. A 66, 024304 (2002)] have claimed that using pairwise entangled qubits gives rise to an exponentially more efficient dense coding when two parties are involved than using maximally entangled qubits shared among N parties. Here we show that their claim is not true.

The Effects of Japan’s Apology for World War II Atrocities on Regional Relations

DTIC Science & Technology

2008-12-01

textbooks and by government officials visiting Yasukuni Shrine, where Japan’s war dead are commemorated. The Japanese counter that they have offered... textbooks , Yasukuni War Shrine, Japan Apology, Article 9. 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT Unclassified 18. SECURITY...World War II. They assert that Japan feels no remorse, as evidenced by treatment of World War II in Japanese school textbooks and by government

Scanning the Human Genome for Novel Therapeutic Targets for Breast Cancer

DTIC Science & Technology

2006-04-01

action of this class of non-coding regulatory RNAs13,14. MicroRNAs are transcribed by RNA polymerase II as long primary polyadenylated transcripts...Artificial miRNAs can be expressed from both RNA polymerase II and III promoters resulting in silencing to varying degrees. At present there...the highest levels of mature microRNA in RISC and generally effective silencing. These structures can be transcribed by either RNA polymerase II or

42 CFR 483.70 - Physical environment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... changes in this edition of the Code are incorporated by reference, CMS will publish notice in the Federal Register to announce the changes. (ii) Chapter 19.3.6.3.2, exception number 2 of the adopted edition of the... resident; (ii) A clean, comfortable mattress; (iii) Bedding appropriate to the weather and climate; and (iv...

42 CFR 483.70 - Physical environment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... changes in this edition of the Code are incorporated by reference, CMS will publish notice in the Federal Register to announce the changes. (ii) Chapter 19.3.6.3.2, exception number 2 of the adopted edition of the... resident; (ii) A clean, comfortable mattress; (iii) Bedding appropriate to the weather and climate; and (iv...

42 CFR 483.70 - Physical environment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... changes in this edition of the Code are incorporated by reference, CMS will publish notice in the Federal Register to announce the changes. (ii) Chapter 19.3.6.3.2, exception number 2 of the adopted edition of the... resident; (ii) A clean, comfortable mattress; (iii) Bedding appropriate to the weather and climate; and (iv...

Definition of the Semisubmersible Floating System for Phase II of OC4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, A.; Jonkman, J.; Masciola, M.

Phase II of the Offshore Code Comparison Collaboration Continuation (OC4) project involved modeling of a semisubmersible floating offshore wind system as shown below. This report documents the specifications of the floating system, which were needed by the OC4 participants for building aero-hydro-servo-elastic models.

Lighting Control Systems Handbook.

DTIC Science & Technology

1985-06-01

cost, both initial and operating. Initially, the control system designer must collect in- formation and then study and weigh several areas including...8217odLe 045. Pearl Harbor. III: Code 11 Pearl Harbor ar ho I ir I L ’ odk 402. R IYI& [’. Plearl II arbor I II: Li bra ry. Pearl HaIitrbor. I ai

5 CFR 302.304 - Order of consideration.

Code of Federal Regulations, 2012 CFR

2012-01-01

... States Code, in the order of his/her numerical ranking. (ii) The name of each other qualified applicant in the order of his/her numerical ranking. (2) Order B. (i) The name of each qualified preference...'s reemployment list, in the order of his/her numerical ranking. (ii) The name of each qualified...

5 CFR 302.304 - Order of consideration.

Code of Federal Regulations, 2011 CFR

2011-01-01

... States Code, in the order of his/her numerical ranking. (ii) The name of each other qualified applicant in the order of his/her numerical ranking. (2) Order B. (i) The name of each qualified preference...'s reemployment list, in the order of his/her numerical ranking. (ii) The name of each qualified...

5 CFR 302.304 - Order of consideration.

Code of Federal Regulations, 2014 CFR

2014-01-01

... States Code, in the order of his/her numerical ranking. (ii) The name of each other qualified applicant in the order of his/her numerical ranking. (2) Order B. (i) The name of each qualified preference...'s reemployment list, in the order of his/her numerical ranking. (ii) The name of each qualified...

5 CFR 302.304 - Order of consideration.

Code of Federal Regulations, 2013 CFR

2013-01-01

... States Code, in the order of his/her numerical ranking. (ii) The name of each other qualified applicant in the order of his/her numerical ranking. (2) Order B. (i) The name of each qualified preference...'s reemployment list, in the order of his/her numerical ranking. (ii) The name of each qualified...

40 CFR 63.2435 - Am I subject to the requirements in this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... MCPU includes equipment necessary to operate a miscellaneous organic chemical manufacturing process, as...)(1)(i), (ii), (iii), (iv), or (v) of this section. (i) An organic chemical(s) classified using the...)(5) of this section. (ii) An organic chemical(s) classified using the 1997 version of NAICS code 325...

40 CFR 63.2435 - Am I subject to the requirements in this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... MCPU includes equipment necessary to operate a miscellaneous organic chemical manufacturing process, as...)(1)(i), (ii), (iii), (iv), or (v) of this section. (i) An organic chemical(s) classified using the...)(5) of this section. (ii) An organic chemical(s) classified using the 1997 version of NAICS code 325...

40 CFR 63.2435 - Am I subject to the requirements in this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... MCPU includes equipment necessary to operate a miscellaneous organic chemical manufacturing process, as...)(1)(i), (ii), (iii), (iv), or (v) of this section. (i) An organic chemical(s) classified using the...)(5) of this section. (ii) An organic chemical(s) classified using the 1997 version of NAICS code 325...

42 CFR 483.70 - Physical environment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... changes in this edition of the Code are incorporated by reference, CMS will publish notice in the Federal Register to announce the changes. (ii) Chapter 19.3.6.3.2, exception number 2 of the adopted edition of the... resident; (ii) A clean, comfortable mattress; (iii) Bedding appropriate to the weather and climate; and (iv...

40 CFR 147.300 - State-administered program-Class II wells.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr... Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re: Class II Well...) Letter from Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re...

40 CFR 147.300 - State-administered program-Class II wells.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr... Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re: Class II Well...) Letter from Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re...

40 CFR 147.300 - State-administered program-Class II wells.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr... Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re: Class II Well...) Letter from Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re...

40 CFR 147.300 - State-administered program-Class II wells.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr... Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re: Class II Well...) Letter from Colorado Assistant Attorney General to the Acting Regional Counsel, EPA Region VIII, “Re...

Inventory Uncertainty Quantification using TENDL Covariance Data in Fispact-II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eastwood, J.W.; Morgan, J.G.; Sublet, J.-Ch., E-mail: jean-christophe.sublet@ccfe.ac.uk

2015-01-15

The new inventory code Fispact-II provides predictions of inventory, radiological quantities and their uncertainties using nuclear data covariance information. Central to the method is a novel fast pathways search algorithm using directed graphs. The pathways output provides (1) an aid to identifying important reactions, (2) fast estimates of uncertainties, (3) reduced models that retain important nuclides and reactions for use in the code's Monte Carlo sensitivity analysis module. Described are the methods that are being implemented for improving uncertainty predictions, quantification and propagation using the covariance data that the recent nuclear data libraries contain. In the TENDL library, above themore » upper energy of the resolved resonance range, a Monte Carlo method in which the covariance data come from uncertainties of the nuclear model calculations is used. The nuclear data files are read directly by FISPACT-II without any further intermediate processing. Variance and covariance data are processed and used by FISPACT-II to compute uncertainties in collapsed cross sections, and these are in turn used to predict uncertainties in inventories and all derived radiological data.« less

A Study of Impairing Injuries in Real World Crashes Using the Injury Impairment Scale (IIS) and the Predicted Functional Capacity Index (PFCI-AIS)

PubMed Central

Barnes, Jo; Morris, Andrew

2009-01-01

The ability to predict impairment outcomes in large databases using a simplified technique allows researchers to focus attention on preventing costly impairing injuries. The dilemma that exists for researchers is to determine which method is the most reliable and valid. This study examines available methods to predict impairment and explores the differences between the IIS and pFCI applied to real world crash injury data. Occupant injury data from the UK Co-operative Crash Injury Study (CCIS) database have been coded using AIS 1990 and AIS 2005. The data have subsequently been recoded using the associated impairment scales namely the Injury Impairment Scale (IIS) and the predicted Functional Capacity Index (pFCI) to determine the predicted impairment levels of injuries at one year post crash. Comparisons between the levels of impairment were made and any differences further explored. Injury data for the period February 2006 to September 2008 from the CCIS database were used in the analysis which involved a dataset of 2,437 occcupants who sustained over 8000 injuries. This study found some differences between the impairment scales for injuries coded to the AIS 1990 and AIS 2005 coding dictionaries. The pFCI predicts 31.5% of injuries to be impairing in AIS 2005, less than the IIS (38.5%) using AIS 1990. Using CCIS data the pFCI predicted that only 6% of the occupants with a coded injury would have an impairing injury compared to 24% of occupants using the IIS. The main body regions identified as having the major differences between the two impairment scales for car occupants were the head and spine. Follow up data were then used for a small number of cases (n=31, lower extremity and whiplash injuries) to examine any differences in predicted impairment versus perceived impairment. These data were selected from a previous study conducted between 2003 and 2006 and identified the discrepancy between predicted impairment and actual perceived impairment as defined by the participant. Overall the work highlights the variaton between the pFCI and IIS and emphasises the importance and need for a single validated impairment scale that can be universally applied. This would allow emphasis to be directed towards preventing injuries that are associated with the most significant impairment outcomes. PMID:20184844

A study of impairing injuries in real world crashes using the Injury Impairment Scale (IIS) and the predicted Functional Capacity Index (PFCI-AIS).

PubMed

Barnes, Jo; Morris, Andrew

2009-10-01

The ability to predict impairment outcomes in large databases using a simplified technique allows researchers to focus attention on preventing costly impairing injuries. The dilemma that exists for researchers is to determine which method is the most reliable and valid. This study examines available methods to predict impairment and explores the differences between the IIS and pFCI applied to real world crash injury data. Occupant injury data from the UK Co-operative Crash Injury Study (CCIS) database have been coded using AIS 1990 and AIS 2005. The data have subsequently been recoded using the associated impairment scales namely the Injury Impairment Scale (IIS) and the predicted Functional Capacity Index (pFCI) to determine the predicted impairment levels of injuries at one year post crash. Comparisons between the levels of impairment were made and any differences further explored. Injury data for the period February 2006 to September 2008 from the CCIS database were used in the analysis which involved a dataset of 2,437 occcupants who sustained over 8000 injuries. This study found some differences between the impairment scales for injuries coded to the AIS 1990 and AIS 2005 coding dictionaries. The pFCI predicts 31.5% of injuries to be impairing in AIS 2005, less than the IIS (38.5%) using AIS 1990. Using CCIS data the pFCI predicted that only 6% of the occupants with a coded injury would have an impairing injury compared to 24% of occupants using the IIS. The main body regions identified as having the major differences between the two impairment scales for car occupants were the head and spine. Follow up data were then used for a small number of cases (n=31, lower extremity and whiplash injuries) to examine any differences in predicted impairment versus perceived impairment. These data were selected from a previous study conducted between 2003 and 2006 and identified the discrepancy between predicted impairment and actual perceived impairment as defined by the participant. Overall the work highlights the variation between the pFCI and IIS and emphasises the importance and need for a single validated impairment scale that can be universally applied. This would allow emphasis to be directed towards preventing injuries that are associated with the most significant impairment outcomes.

Study of helium emissions from active solar regions

NASA Technical Reports Server (NTRS)

Kulander, J. L.

1973-01-01

A theoretical study is made of the visible and UV line radiation of He I atoms and He II ions from a plane-parallel model flare layer. Codes were developed for the solution of the statistically steady state equation for a 30 level He I - II - III model, and the line and continuum transport equations. These codes are described and documented in the report along with sample solutions. Optical depths and some line intensities are presented for a 1000 km thick layer. Solutions of the steady state equations are presented for electron temperatures 10,000 to 50,000 K and electron densities 10 to the 10th power to 10 to the 14th power/cu cm.

PHISICS/RELAP5-3D RESULTS FOR EXERCISES II-1 AND II-2 OF THE OECD/NEA MHTGR-350 BENCHMARK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strydom, Gerhard

2016-03-01

The Idaho National Laboratory (INL) Advanced Reactor Technologies (ART) High-Temperature Gas-Cooled Reactor (HTGR) Methods group currently leads the Modular High-Temperature Gas-Cooled Reactor (MHTGR) 350 benchmark. The benchmark consists of a set of lattice-depletion, steady-state, and transient problems that can be used by HTGR simulation groups to assess the performance of their code suites. The paper summarizes the results obtained for the first two transient exercises defined for Phase II of the benchmark. The Parallel and Highly Innovative Simulation for INL Code System (PHISICS), coupled with the INL system code RELAP5-3D, was used to generate the results for the Depressurized Conductionmore » Cooldown (DCC) (exercise II-1a) and Pressurized Conduction Cooldown (PCC) (exercise II-2) transients. These exercises require the time-dependent simulation of coupled neutronics and thermal-hydraulics phenomena, and utilize the steady-state solution previously obtained for exercise I-3 of Phase I. This paper also includes a comparison of the benchmark results obtained with a traditional system code “ring” model against a more detailed “block” model that include kinetics feedback on an individual block level and thermal feedbacks on a triangular sub-mesh. The higher spatial fidelity that can be obtained by the block model is illustrated with comparisons of the maximum fuel temperatures, especially in the case of natural convection conditions that dominate the DCC and PCC events. Differences up to 125 K (or 10%) were observed between the ring and block model predictions of the DCC transient, mostly due to the block model’s capability of tracking individual block decay powers and more detailed helium flow distributions. In general, the block model only required DCC and PCC calculation times twice as long as the ring models, and it therefore seems that the additional development and calculation time required for the block model could be worth the gain that can be obtained in the spatial resolution« less

New techniques for modeling the reliability of reactor pressure vessels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, K.I.; Simonen, F.A.; Liebetrau, A.M.

1986-01-01

In recent years several probabilistic fracture mechanics codes, including the VISA code, have been developed to predict the reliability of reactor pressure vessels. This paper describes several new modeling techniques used in a second generation of the VISA code entitled VISA-II. Results are presented that show the sensitivity of vessel reliability predictions to such factors as inservice inspection to detect flaws, random positioning of flaws within the vessel wall thickness, and fluence distributions that vary throughout the vessel. The algorithms used to implement these modeling techniques are also described. Other new options in VISA-II are also described in this paper.more » The effect of vessel cladding has been included in the heat transfer, stress, and fracture mechanics solutions in VISA-II. The algorithms for simulating flaws has been changed to consider an entire vessel rather than a single flaw in a single weld. The flaw distribution was changed to include the distribution of both flaw depth and length. A menu of several alternate equations has been included to predict the shift in RT/sub NDT/. For flaws that arrest and later re-initiate, an option was also included to allow correlating the current arrest toughness with subsequent initiation toughnesses.« less

Commandant's international technical series. Volume 9. International regulations on the prevention of pollution from ships carrying hazardous chemicals in bulk. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-12-01

MARPOL was developed to minimize accidental and operational pollution from ships carrying noxious liquid substances in bulk. Accidental pollution could result from a collision, a grounding, or an overflow of a cargo tank. Operational pollution results from the disposal of cargo tank washings. Major amendments were made to the original Annex II by the International Maritime Organization. The United States and other States party to MARPOL will implement Annex II, as amended, on April 7, 1987. Implementation will affect seagoing ships transporting noxious liquid substances to and from such ships. The attached documents contain internationally agreed requirements, interpretations, and guidelinesmore » necessary for the implementation of Annex II. The documents attached include: (1) MARPOL Annex II as amended by amendments adopted by the twenty-second session of the IMO Marine Environment Protection Committee; (2) Unified Interpretations of Annex II; (3) Standards for the Procedures and Arrangements for the Discharge of Noxious Liquid Substances; (4) Ammendments to the Bulk Chemical Code and the International Bulk Chemical Code to include marine pollution concerns; (5) Guidelines on the Provision of Adequate Reception Facilities in Ports, Part II (Noxious Liquid Substances). The contents of these documents are being placed in regulations. The purpose of this document is to give members of the interested public advance notification of impending regulations.« less

76 FR 36979 - Golden Parachute and Indemnification Payments-Technical Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-24

...: Pamela Yu, Staff Attorney, Office of General Counsel, or Ross Kendall, Special Counsel to the General... the Internal Revenue Code of 1986, 26 U.S.C. 457(b), or a pension or retirement plan that is qualified... Revenue Code of 1986, 26 U.S.C. 401; or (ii) * * * [FR Doc. 2011-15729 Filed 6-23-11; 8:45 am] BILLING...

REXOR 2 rotorcraft simulation model. Volume 1: Engineering documentation

NASA Technical Reports Server (NTRS)

Reaser, J. S.; Kretsinger, P. H.

1978-01-01

A rotorcraft nonlinear simulation called REXOR II, divided into three volumes, is described. The first volume is a development of rotorcraft mechanics and aerodynamics. The second is a development and explanation of the computer code required to implement the equations of motion. The third volume is a user's manual, and contains a description of code input/output as well as operating instructions.

34 CFR 685.207 - Obligation to repay.

Code of Federal Regulations, 2010 CFR

2010-07-01

... title 10, United States Code and is called or ordered to active duty for a period of more than 30 days... period when called or ordered to active duty as specified in paragraph (b)(2)(ii)(A) of this section is... of title 10, United States Code and is called or ordered to active duty for a period of more than 30...

77 FR 33635 - Amendment to the Bank Secrecy Act Regulations-Requirement That Clerks of Court Report Certain...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-07

... BSA and associated regulations.\\3\\ FinCEN is authorized to impose anti-money laundering (``AML... Code); (iii) Money laundering (as defined in section 1956 or 1957 of title 18 of the United States Code... money in the country in which issued; and (ii) A cashier's check (by whatever name called, including...

The Design and Implementation of a Read Prediction Buffer

DTIC Science & Technology

1992-12-01

City, State, and ZIP Code) 7b ADDRESS (City, State. and ZIP Code) 8a. NAME OF FUNDING /SPONSORING 8b. OFFICE SYMBOL 9 PROCUREMENT INSTRUMENT... 9 E. THESIS STRUCTURE.. . .... ............... 9 II. READ PREDICTION ALGORITHM AND BUFFER DESIGN 10 A. THE READ PREDICTION ALGORITHM...29 Figure 9 . Basic Multiplexer Cell .... .......... .. 30 Figure 10. Block Diagram Simulation Labels ......... 38 viii I. INTRODUCTION A

78 FR 49512 - Clean Water Act Class II: Proposed Administrative Settlement, Penalty Assessment and Opportunity...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-14

....gov Web site is an ``anonymous access'' system, which means the EPA will not know your identity or... request exemptions in accordance with Ala. Admin. Code r. 335-3-14- 01(1) and (5). Respondent operated... Title 129 of Neb. Admin. Code 17-001.01. Respondent operated an emergency generator at its facility...

Parallel Higher-order Finite Element Method for Accurate Field Computations in Wakefield and PIC Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Candel, A.; Kabel, A.; Lee, L.

Over the past years, SLAC's Advanced Computations Department (ACD), under SciDAC sponsorship, has developed a suite of 3D (2D) parallel higher-order finite element (FE) codes, T3P (T2P) and Pic3P (Pic2P), aimed at accurate, large-scale simulation of wakefields and particle-field interactions in radio-frequency (RF) cavities of complex shape. The codes are built on the FE infrastructure that supports SLAC's frequency domain codes, Omega3P and S3P, to utilize conformal tetrahedral (triangular)meshes, higher-order basis functions and quadratic geometry approximation. For time integration, they adopt an unconditionally stable implicit scheme. Pic3P (Pic2P) extends T3P (T2P) to treat charged-particle dynamics self-consistently using the PIC (particle-in-cell)more » approach, the first such implementation on a conformal, unstructured grid using Whitney basis functions. Examples from applications to the International Linear Collider (ILC), Positron Electron Project-II (PEP-II), Linac Coherent Light Source (LCLS) and other accelerators will be presented to compare the accuracy and computational efficiency of these codes versus their counterparts using structured grids.« less

Micrometeoroid and Orbital Debris Threat Assessment: Mars Sample Return Earth Entry Vehicle

NASA Technical Reports Server (NTRS)

Christiansen, Eric L.; Hyde, James L.; Bjorkman, Michael D.; Hoffman, Kevin D.; Lear, Dana M.; Prior, Thomas G.

2011-01-01

This report provides results of a Micrometeoroid and Orbital Debris (MMOD) risk assessment of the Mars Sample Return Earth Entry Vehicle (MSR EEV). The assessment was performed using standard risk assessment methodology illustrated in Figure 1-1. Central to the process is the Bumper risk assessment code (Figure 1-2), which calculates the critical penetration risk based on geometry, shielding configurations and flight parameters. The assessment process begins by building a finite element model (FEM) of the spacecraft, which defines the size and shape of the spacecraft as well as the locations of the various shielding configurations. This model is built using the NX I-deas software package from Siemens PLM Software. The FEM is constructed using triangular and quadrilateral elements that define the outer shell of the spacecraft. Bumper-II uses the model file to determine the geometry of the spacecraft for the analysis. The next step of the process is to identify the ballistic limit characteristics for the various shield types. These ballistic limits define the critical size particle that will penetrate a shield at a given impact angle and impact velocity. When the finite element model is built, each individual element is assigned a property identifier (PID) to act as an index for its shielding properties. Using the ballistic limit equations (BLEs) built into the Bumper-II code, the shield characteristics are defined for each and every PID in the model. The final stage of the analysis is to determine the probability of no penetration (PNP) on the spacecraft. This is done using the micrometeoroid and orbital debris environment definitions that are built into the Bumper-II code. These engineering models take into account orbit inclination, altitude, attitude and analysis date in order to predict an impacting particle flux on the spacecraft. Using the geometry and shielding characteristics previously defined for the spacecraft and combining that information with the environment model calculations, the Bumper-II code calculates a probability of no penetration for the spacecraft.

The chloroplast tRNALys(UUU) gene from mustard (Sinapis alba) contains a class II intron potentially coding for a maturase-related polypeptide.

PubMed

Neuhaus, H; Link, G

1987-01-01

The trnK gene endocing the tRNALys(UUU) has been located on mustard (Sinapis alba) chloroplast DNA, 263 bp upstream of the psbA gene on the same strand. The nucleotide sequence of the trnK gene and its flanking regions as well as the putative transcription start and termination sites are shown. The 5' end of the transcript lies 121 bp upstream of the 5' tRNA coding region and is preceded by procaryotic-type "-10" and "-35" sequence elements, while the 3' end maps 2.77 kb downstream to a DNA region with possible stemloop secondary structure. The anticodon loop of the tRNALys is interrupted by a 2,574 bp intron containing a long open reading frame, which codes for 524 amino acids. Based on conserved stem and loop structures, this intron has characteristic features of a class II intron. A region near the carboxyl terminus of the derived polypeptide appears structurally related to maturases.

1 CFR 21.11 - Standard organization of the Code of Federal Regulations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... PREPARATION, TRANSMITTAL, AND PROCESSING OF DOCUMENTS PREPARATION OF DOCUMENTS SUBJECT TO CODIFICATION General... (h) Paragraphs, which are designated as follows: level 1(a), (b), (c), etc. level 2(1), (2), (3), etc. level 3(i), (ii), (iii), etc. level 4(A), (B), (C), etc. level 5(1), (2), (3), etc. level 6(i), (ii...

2 CFR 1.200 - Purpose of chapters I and II.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 2 Grants and Agreements 1 2014-01-01 2014-01-01 false Purpose of chapters I and II. 1.200 Section 1.200 Grants and Agreements Office of Management and Budget Guidance for Grants and Agreements ABOUT TITLE 2 OF THE CODE OF FEDERAL REGULATIONS AND SUBTITLE A Introduction to Subtitle A § 1.200 Purpose of...

2 CFR 1.200 - Purpose of chapters I and II.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 2 Grants and Agreements 1 2013-01-01 2013-01-01 false Purpose of chapters I and II. 1.200 Section 1.200 Grants and Agreements Office of Management and Budget Guidance for Grants and Agreements ABOUT TITLE 2 OF THE CODE OF FEDERAL REGULATIONS AND SUBTITLE A Introduction toSubtitle A § 1.200 Purpose of...

2 CFR 1.200 - Purpose of chapters I and II.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 2 Grants and Agreements 1 2012-01-01 2012-01-01 false Purpose of chapters I and II. 1.200 Section 1.200 Grants and Agreements Office of Management and Budget Guidance for Grants and Agreements ABOUT TITLE 2 OF THE CODE OF FEDERAL REGULATIONS AND SUBTITLE A Introduction to Subtitle A § 1.200 Purpose of...

46 CFR 164.019-3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Guard-approved PFDs. Commandant means the Chief of the Lifesaving and Fire Safety Division, Office of... code PFD type acceptable for use 1 I, II, and III. 2 II and III. 3 III. 4B IV (all Ring Buoys). 4BC IV (Buoyant Cushions). 4RB IV (Recreational Ring Buoys only). 5 Wearable Type V (intended use must be...

29 CFR 4022.81 - General rules.

Code of Federal Regulations, 2011 CFR

2011-07-01

... after May 1998, the applicable federal mid-term rate (as determined by the Secretary of the Treasury pursuant to section 1274(d)(1)(C)(ii) of the Code) for that month (or, where the rate for a month is not... which the rate is available) based on monthly compounding; and (ii) For May 1998 and earlier months, the...

29 CFR 4022.81 - General rules.

Code of Federal Regulations, 2012 CFR

2012-07-01

... after May 1998, the applicable federal mid-term rate (as determined by the Secretary of the Treasury pursuant to section 1274(d)(1)(C)(ii) of the Code) for that month (or, where the rate for a month is not... which the rate is available) based on monthly compounding; and (ii) For May 1998 and earlier months, the...

29 CFR 4022.81 - General rules.

Code of Federal Regulations, 2014 CFR

2014-07-01

... after May 1998, the applicable federal mid-term rate (as determined by the Secretary of the Treasury pursuant to section 1274(d)(1)(C)(ii) of the Code) for that month (or, where the rate for a month is not... which the rate is available) based on monthly compounding; and (ii) For May 1998 and earlier months, the...

29 CFR 4022.81 - General rules.

Code of Federal Regulations, 2013 CFR

2013-07-01

... after May 1998, the applicable federal mid-term rate (as determined by the Secretary of the Treasury pursuant to section 1274(d)(1)(C)(ii) of the Code) for that month (or, where the rate for a month is not... which the rate is available) based on monthly compounding; and (ii) For May 1998 and earlier months, the...

138. ARAII Building ARA606 floor plan for remodel as Inel ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

138. ARA-II Building ARA-606 floor plan for remodel as Inel Welding Laboratory. Shows room divisions and welding stations to be installed. Aerojet Nuclear Company 1375-ARA-II-606-E-2. Date: June 1976. Ineel index code no. 070-0606-10-400-156552. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

40 CFR 147.2551 - State-administered program-Class II wells.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr..., “Re: Application for Primacy in the Regulation of Class II Injection Wells,” March 8, 1982; (5) Letter from State Oil and Gas Supervisor, Wyoming Oil and Gas Conservation Commission, to EPA Region VIII, “Re...

40 CFR 147.2551 - State-administered program-Class II wells.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr..., “Re: Application for Primacy in the Regulation of Class II Injection Wells,” March 8, 1982; (5) Letter from State Oil and Gas Supervisor, Wyoming Oil and Gas Conservation Commission, to EPA Region VIII, “Re...

40 CFR 147.2551 - State-administered program-Class II wells.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr..., “Re: Application for Primacy in the Regulation of Class II Injection Wells,” March 8, 1982; (5) Letter from State Oil and Gas Supervisor, Wyoming Oil and Gas Conservation Commission, to EPA Region VIII, “Re...

40 CFR 147.2551 - State-administered program-Class II wells.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr..., “Re: Application for Primacy in the Regulation of Class II Injection Wells,” March 8, 1982; (5) Letter from State Oil and Gas Supervisor, Wyoming Oil and Gas Conservation Commission, to EPA Region VIII, “Re...

40 CFR 147.2551 - State-administered program-Class II wells.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr..., “Re: Application for Primacy in the Regulation of Class II Injection Wells,” March 8, 1982; (5) Letter from State Oil and Gas Supervisor, Wyoming Oil and Gas Conservation Commission, to EPA Region VIII, “Re...

Interpretive computer simulator for the NASA Standard Spacecraft Computer-2 (NSSC-2)

NASA Technical Reports Server (NTRS)

Smith, R. S.; Noland, M. S.

1979-01-01

An Interpretive Computer Simulator (ICS) for the NASA Standard Spacecraft Computer-II (NSSC-II) was developed as a code verification and testing tool for the Annular Suspension and Pointing System (ASPS) project. The simulator is written in the higher level language PASCAL and implented on the CDC CYBER series computer system. It is supported by a metal assembler, a linkage loader for the NSSC-II, and a utility library to meet the application requirements. The architectural design of the NSSC-II is that of an IBM System/360 (S/360) and supports all but four instructions of the S/360 standard instruction set. The structural design of the ICS is described with emphasis on the design differences between it and the NSSC-II hardware. The program flow is diagrammed, with the function of each procedure being defined; the instruction implementation is discussed in broad terms; and the instruction timings used in the ICS are listed. An example of the steps required to process an assembly level language program on the ICS is included. The example illustrates the control cards necessary to assemble, load, and execute assembly language code; the sample program to to be executed; the executable load module produced by the loader; and the resulting output produced by the ICS.

Arctic Ice Dynamics Joint Experiment 1975-1976. Physical Oceanography Data Report, Salinity, Temperature and Depth Data, Camp Blue Fox. Volume II.

DTIC Science & Technology

1980-02-01

to LM b. a w ewe%- ww re mOOc 4" o 0.NWmotvviiOf wt 00 f4Crfl ft -wm o.e. &*1 NO P..w N N o%9 a in - - -da inN 4p m a - U . .......0...V N m...200 1 Attn: Code 428AR 3 Attn: Code 420 a Director Naval Research Laboratory Washington, D.C. 20375 Attn: Library . Code 2620 1 U.S. Naval Research

Solid Geometric Modeling - The Key to Improved Materiel Acquisition from Concept to Deployment

DTIC Science & Technology

1984-09-01

M. J. Reisinger, "The GIFT Code User Manual; Volume I, Introduction and Input Requirements (U)," BRL Report No. 1802, July 1975. AD# A078364. 8 G...G. Kuehl, L. W. Bain, Jr., M. J. Reisinger, "The GIFT Code User Manual; Volume II, The Output Options (U)," USA ARRAOCOM Report No. 02189, Sep 79, AD...A078364 . • These results are plotted by a code called RunShot written by L. M. Rybak which takes input from GIFT and plots color shotlines on a

General Electromagnetic Model for the Analysis of Complex Systems (GEMACS) Computer Code Documentation (Version 3). Volume 3, Part 4.

DTIC Science & Technology

1983-09-01

6ENFRAL. ELECTROMAGNETIC MODEL FOR THE ANALYSIS OF COMPLEX SYSTEMS **%(GEMA CS) Computer Code Documentation ii( Version 3 ). A the BDM Corporation Dr...ANALYSIS FnlTcnclRpr F COMPLEX SYSTEM (GmCS) February 81 - July 83- I TR CODE DOCUMENTATION (Version 3 ) 6.PROMN N.REPORT NUMBER 5. CONTRACT ORGAT97...the ti and t2 directions on the source patch. 3 . METHOD: The electric field at a segment observation point due to the source patch j is given by 1-- lnA

SKYSHINE-II procedure: calculation of the effects of structure design on neutron, primary gamma-ray and secondary gamma-ray dose rates in air. Supplement number 1. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lampley, C.M.

1981-01-01

This report describes many of the computational methods employed within the SKYSHINE-II program. A brief description of the new data base is included, as is a description of the input data requirements and formats needed to properly execute a SKYSHINE-II problem. Utilization instructions for the program are provided for operation of the SKYSHINE-II Code on the Brookhaven National Laboratory Central Scientific Computing Facility (See NUREG/CR-0781, RRA-T7901 for complete information).

Air Weather Service (AWS) Climatic Briefs: Europe.

DTIC Science & Technology

1982-05-01

UNCLASSIFIED USAFETAC/DS-/81/05b SBI-AD-ESS0 187 N1 II NI I MEhhhh IIIIIIIIIIIIIIIII II hh PHOTOGRAPH THIS SHEET E /8 LEVEL INVENTORY DOCUMENT IDENTIFICATION...JUSTIFICATnON S ELE3 C T E BY S U 3M DISTRIBUTIO - D AVAILABILITY CODES DIST AVAIL AND/OR SPECIAL DATE ACCESSIONED DISTRIBUTION STAMP 82 08 02 147...publication. WAYNE E McCOLLOM Chief, chnical Information Section FOR THE COMMANDER WALTER S. BURGMANN Scientific and Technical Information Officer (STINFO) ii

A User’s Manual for: Electromagnetic Surface Patch Code (ESP).

DTIC Science & Technology

1981-07-01

NEWMAN DAAG29-81-K-0020 UNCLASSIFIED ESL-713402- 1 AR0-17UU6.1-EL NL I OF | AD A 10 5 954 END DATE FILMED II-.8I1 DTIC SM * - III 1.0 :s...ma III ̂ ^= • ilia II I.I III— = 11.25 [I 11.4 1 ^6 t v 1 ...Ohio State University ElectroScience Laboratory Department of Electrical Engineering Columbu», Ohio 43212 Technical Report 713402- 1 Grant Number

Conjoin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sjaardema, Gregory

2010-08-06

Conjoin is a code for joining sequentially in time multiple exodusII database files. It is used to create a single results or restart file from multiple results or restart files which typically arise as the result of multiple restarted analyses. The resulting output file will be the union of the input files with a status variable indicating the status of each element at the various time planes.Combining multiple exodusII files arising from a restarted analysis or combining multiple exodusII files arising from a finite element analysis with dynamic topology changes.

CIFOG: Cosmological Ionization Fields frOm Galaxies

NASA Astrophysics Data System (ADS)

Hutter, Anne

2018-03-01

CIFOG is a versatile MPI-parallelised semi-numerical tool to perform simulations of the Epoch of Reionization. From a set of evolving cosmological gas density and ionizing emissivity fields, it computes the time and spatially dependent ionization of neutral hydrogen (HI), neutral (HeI) and singly ionized helium (HeII) in the intergalactic medium (IGM). The code accounts for HII, HeII, HeIII recombinations, and provides different descriptions for the photoionization rate that are used to calculate the residual HI fraction in ionized regions. This tool has been designed to be coupled to semi-analytic galaxy formation models or hydrodynamical simulations. The modular fashion of the code allows the user to easily introduce new descriptions for recombinations and the photoionization rate.

Ioss IO Subsystem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sjaardema, Gregory; Bauer, David; Erik, & Illescas

2017-01-06

The Ioss is a database-independent package for providing an object-oriented, abstract interface to IO capabilities for a finite element application; and concrete database interfaces which provided input and/or output to exodusII, xdmf, generated, and heartbeat database formats. The Ioss provides an object-oriented C++-based IO interface for a finite element application code. The application code can perform all IO operations through the Ioss interface which is typically at a higher abstraction level than the concrete database formats. The Ioss then performs the needed operations to translate the finite element data to the specific format required by the concrete database implementations. Themore » Ioss currently supports interfaces to exodusII, xdmf, generated, and heartbeat formats, but additional formats can be easily added.« less

EBR-II Static Neutronic Calculations by PHISICS / MCNP6 codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paolo Balestra; Carlo Parisi; Andrea Alfonsi

2016-02-01

The International Atomic Energy Agency (IAEA) launched a Coordinated Research Project (CRP) on the Shutdown Heat Removal Tests (SHRT) performed in the '80s at the Experimental fast Breeder Reactor EBR-II, USA. The scope of the CRP is to improve and validate the simulation tools for the study and the design of the liquid metal cooled fast reactors. Moreover, training of the next generation of fast reactor analysts is being also considered the other scope of the CRP. In this framework, a static neutronic model was developed, using state-of-the art neutron transport codes like SCALE/PHISICS (deterministic solution) and MCNP6 (stochastic solution).more » Comparison between both solutions is briefly illustrated in this summary.« less

Visual Form Detection in 3-Dimensional Space.

DTIC Science & Technology

1982-10-01

RR04209 Ann Arbor, Michigan 48109 RR0429002; NR 197-070 - II CONTROLLING OFFICE NAME AND ADDRESS 12. REPORT DATE Engineering Psychology Group ( Code...93940 Pasadena, CA 91106 Dean of Research Administration Office of Naval Research Naval Postgraduate School Scientific Liaison Group Monterey, CA...Eisenhower Avenue Dr. Gloria Chisum Alexandria, VA 22333 Sciences Research Group Code 6003 Naval Air Development Center Warminste.’, PA 18974 -4- Department

2 CFR 1.200 - Purpose of chapters I and II.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 2 Grants and Agreements 1 2011-01-01 2011-01-01 false Purpose of chapters I and II. 1.200 Section 1.200 Grants and Agreements Office of Management and Budget Guidance for Grants and Agreements ABOUT TITLE 2 OF THE CODE OF FEDERAL REGULATIONS AND SUBTITLE A Introduction toSubtitle A § 1.200 Purpose of...

REGULATIONS PURSUANT TO TITLES I, II, AND III OF THE ELEMENTARY AND SECONDARY EDUCATION ACT OF 1965.

ERIC Educational Resources Information Center

HOWE, HAROLD, II; GARDNER, JOHN W.

IN ADDITION TO DEFINITIONS, SPECIFIC PROVISIONS ARE GIVEN FOR THREE REVISED SECTIONS OF TITLE 45 OF THE CODE OF FEDERAL REGULATIONS CONCERNING TITLES I, II, AND III OF THE ELEMENTARY AND SECONDARY EDUCATION ACT OF 1965. PART 116, "FINANCIAL ASSISTANCE TO MEET THE SPECIAL EDUCATIONAL NEEDS OF EDUCATIONALLY DEPRIVED CHILDREN," INCLUDES…

137. ARAII Building ARA602 floor plan as it appeared in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

137. ARA-II Building ARA-602 floor plan as it appeared in 1980 when electrical modifications were being made. Shows partial layout of floor plan. EG&G Idaho, Inc. 1570-ARA-II-602-E-3. Date: April 1980. Ineel index code no. 070--0602-10-220-159761. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

Advancing the Assessment of Parent-Child Interactions: Development of the Parent Instruction-Giving Game with Youngsters

ERIC Educational Resources Information Center

Hupp, Stephen D. A.; Reitman, David; Forde, Debra A.; Shriver, Mark D.; Kelley, Mary Lou

2008-01-01

This study investigates the validity of the Parent Instruction-Giving Game with Youngsters (PIGGY), a newly developed direct-observation system. The PIGGY is a derivative of the Dyadic Parent-Child Interaction Coding System II [DPICS-II; Eyberg, S. M., Bessmer, J., Newcomb, K., Edwards, D., Robinson, E. (1994). Manual for the Dyadic Parent-Child…

26 CFR 1.1291-0 - Treatment of shareholders of certain passive foreign investment companies; table of contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

... market rules under chapter 1 of the Internal Revenue Code other than section 1296. (i) In general. (ii.... (f) through (i) [Reserved] (j) Effective date. § 1.1291-9 Deemed dividend election. (a) Deemed dividend election. (1) In general. (2) Post-1986 earnings and profits defined. (i) In general. (ii) Pro...

76 FR 40935 - Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-12

.... Claim No. LIB-I-007; 4 p.m. Claim No. LIB-II-007 Friday, July 22, 2011 10 a.m. Claim No. LIB-II-001; 10...) 616-6975. Judith H. Lock, Executive Officer. [FR Doc. 2011-17632 Filed 7-8-11; 4:15 pm] BILLING CODE... FOREIGN CLAIMS SETTLEMENT COMMISSION [F.C.S.C. Meeting and Hearing Notice No. 5-11] Sunshine Act...

Mortality in Code Blue; can APACHE II and PRISM scores be used as markers for prognostication?

PubMed

Bakan, Nurten; Karaören, Gülşah; Tomruk, Şenay Göksu; Keskin Kayalar, Sinem

2018-03-01

Code blue (CB) is an emergency call system developed to respond to cardiac and respiratory arrest in hospitals. However, in literature, no scoring system has been reported that can predict mortality in CB procedures. In this study, we aimed to investigate the effectiveness of estimated APACHE II and PRISM scores in the prediction of mortality in patients assessed using CB to retrospectively analyze CB calls. We retrospectively examined 1195 patients who were evaluated by the CB team at our hospital between 2009 and 2013. The demographic data of the patients, diagnosis and relevant de-partments, reasons for CB, cardiopulmonary resuscitation duration, mortality calculated from the APACHE II and PRISM scores, and the actual mortality rates were retrospectively record-ed from CB notification forms and the hospital database. In all age groups, there was a significant difference between actual mortality rate and the expected mortality rate as estimated using APACHE II and PRISM scores in CB calls (p<0.05). The actual mortality rate was significantly lower than the expected mortality. APACHE and PRISM scores with the available parameters will not help predict mortality in CB procedures. Therefore, novels scoring systems using different parameters are needed.

WEC3: Wave Energy Converter Code Comparison Project: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Combourieu, Adrien; Lawson, Michael; Babarit, Aurelien

This paper describes the recently launched Wave Energy Converter Code Comparison (WEC3) project and present preliminary results from this effort. The objectives of WEC3 are to verify and validate numerical modelling tools that have been developed specifically to simulate wave energy conversion devices and to inform the upcoming IEA OES Annex VI Ocean Energy Modelling Verification and Validation project. WEC3 is divided into two phases. Phase 1 consists of a code-to-code verification and Phase II entails code-to-experiment validation. WEC3 focuses on mid-fidelity codes that simulate WECs using time-domain multibody dynamics methods to model device motions and hydrodynamic coefficients to modelmore » hydrodynamic forces. Consequently, high-fidelity numerical modelling tools, such as Navier-Stokes computational fluid dynamics simulation, and simple frequency domain modelling tools were not included in the WEC3 project.« less

24 CFR 905.10 - Capital Fund formula (CFF).

Code of Federal Regulations, 2013 CFR

2013-04-01

... projects; (ii) Vacancy reduction; (iii) Addressing deferred maintenance needs and the replacement of obsolete utility systems and dwelling equipment; (iv) Planned code compliance; (v) Management improvements...

24 CFR 905.10 - Capital Fund formula (CFF).

Code of Federal Regulations, 2012 CFR

2012-04-01

... projects; (ii) Vacancy reduction; (iii) Addressing deferred maintenance needs and the replacement of obsolete utility systems and dwelling equipment; (iv) Planned code compliance; (v) Management improvements...

Alternate pathways of thyroid hormone metabolism.

PubMed

Wu, Sing-Yung; Green, William L; Huang, Wen-Sheng; Hays, Marguerite T; Chopra, Inder J

2005-08-01

The major thyroid hormone (TH) secreted by the thyroid gland is thyroxine (T(4)). Triiodothyronine (T(3)), formed chiefly by deiodination of T(4), is the active hormone at the nuclear receptor, and it is generally accepted that deiodination is the major pathway regulating T(3) bioavailability in mammalian tissues. The alternate pathways, sulfation and glucuronidation of the phenolic hydroxyl group of iodothyronines, the oxidative deamination and decarboxylation of the alanine side chain to form iodothyroacetic acids, and ether link cleavage provide additional mechanisms for regulating the supply of active hormone. Sulfation may play a general role in regulation of iodothyronine metabolism, since sulfation of T(4) and T(3) markedly accelerates deiodination to the inactive metabolites, reverse triiodothyronine (rT(3)) and T(2). Sulfoconjugation is prominent during intrauterine development, particularly in the precocial species in the last trimester including humans and sheep, where it may serve both to regulate the supply of T(3), via sulfation followed by deiodination, and to facilitate maternal-fetal exchange of sulfated iodothyronines (e.g., 3,3'-diiodothyronine sulfate [T(2)S]). The resulting low serum T(3) may be important for normal fetal development in the late gestation. The possibility that T(2)S or its derivative, transferred from the fetus and appearing in maternal serum or urine, can serve as a marker of fetal thyroid function is being studied. Glucuronidation of TH often precedes biliary-fecal excretion of hormone. In rats, stimulation of glucuronidation by various drugs and toxins may lead to lower T(4) and T(3) levels, provocation of thyrotropin (TSH) secretion, and goiter. In man, drug induced stimulation of glucuronidation is limited to T(4), and does not usually compromise normal thyroid function. However, in hypothyroid subjects, higher doses of TH may be required to maintain euthyroidism when these drugs are given. In addition, glucuronidates and sulfated iodothyronines can be hydrolyzed to their precursors in gastrointestinal tract and various tissues. Thus, these conjugates can serve as a reservoir for biologically active iodothyronines (e.g., T(4), T(3), or T(2)). The acetic acid derivatives of T(4), tetrac and triac, are minor products in normal thyroid physiology. However, triac has a different pattern of receptor affinity than T(3), binding preferentially to the beta receptor. This makes it useful in the treatment of the syndrome of resistance to thyroid hormone action, where the typical mutation affects only the beta receptor. Thus, adequate binding to certain mutated beta receptors can be achieved without excessive stimulation of alpha receptors, which predominate in the heart. Ether link cleavage of TH is also a minor pathway in normal subjects. However, this pathway may become important during infections, when augmented TH breakdown by ether-link cleavage (ELC) may assist in bactericidal activity. There is a recent claim that decarboxylated derivates of thyronines, that is, monoiodothyronamine (T(1)am) and thyronamine (T(0)am), may be biologically important and have actions different from those of TH. Further information on these interesting derivatives is awaited.

An Interactive and Comprehensive Working Environment for High-Energy Physics Software with Python and Jupyter Notebooks

NASA Astrophysics Data System (ADS)

Braun, N.; Hauth, T.; Pulvermacher, C.; Ritter, M.

2017-10-01

Today’s analyses for high-energy physics (HEP) experiments involve processing a large amount of data with highly specialized algorithms. The contemporary workflow from recorded data to final results is based on the execution of small scripts - often written in Python or ROOT macros which call complex compiled algorithms in the background - to perform fitting procedures and generate plots. During recent years interactive programming environments, such as Jupyter, became popular. Jupyter allows to develop Python-based applications, so-called notebooks, which bundle code, documentation and results, e.g. plots. Advantages over classical script-based approaches is the feature to recompute only parts of the analysis code, which allows for fast and iterative development, and a web-based user frontend, which can be hosted centrally and only requires a browser on the user side. In our novel approach, Python and Jupyter are tightly integrated into the Belle II Analysis Software Framework (basf2), currently being developed for the Belle II experiment in Japan. This allows to develop code in Jupyter notebooks for every aspect of the event simulation, reconstruction and analysis chain. These interactive notebooks can be hosted as a centralized web service via jupyterhub with docker and used by all scientists of the Belle II Collaboration. Because of its generality and encapsulation, the setup can easily be scaled to large installations.

Novel mutations in the CHST6 gene associated with macular corneal dystrophy in southern India.

PubMed

Warren, John F; Aldave, Anthony J; Srinivasan, M; Thonar, Eugene J; Kumar, Abha B; Cevallos, Vicky; Whitcher, John P; Margolis, Todd P

2003-11-01

To further characterize the role of the carbohydrate sulfotransferase (CHST6) gene in macular corneal dystrophy (MCD) through identification of causative mutations in a cohort of affected patients from southern India. Genomic DNA was extracted from buccal epithelium of 75 patients (51 families) with MCD, 33 unaffected relatives, and 48 healthy volunteers. The coding region of the CHST6 gene was evaluated by means of polymerase chain reaction amplification and direct sequencing. Subtyping of MCD into types I and II was performed by measuring serum levels of antigenic keratan sulfate. Seventy patients were classified as having type I MCD, and 5 patients as having type II MCD. Analysis of the CHST6 coding region in patients with type I MCD identified 11 homozygous missense mutations (Leu22Arg, His42Tyr, Arg50Cys, Arg50Leu, Ser53Leu, Arg97Pro, Cys102Tyr, Arg127Cys, Arg205Gln, His249Pro, and Glu274Lys), 2 compound heterozygous missense mutations (Arg93His and Ala206Thr), 5 homozygous deletion mutations (delCG707-708, delC890, delA1237, del1748-1770, and delORF), and 2 homozygous replacement mutations (ACCTAC 1273 GGT, and GCG 1304 AT). One patient with type II MCD was heterozygous for the C890 deletion mutation, whereas 4 possessed no CHST6 coding region mutations. A variety of previously unreported mutations in the coding region of the CHST6 gene are associated with type I MCD in a cohort of patients in southern India. An improved understanding of the genetic basis of MCD allows for earlier, more accurate diagnosis of affected individuals, and may provide the foundation for the development of novel disease treatments.

Statistical Evaluation of the Rodin–Ohno Hypothesis: Sense/Antisense Coding of Ancestral Class I and II Aminoacyl-tRNA Synthetases

PubMed Central

Chandrasekaran, Srinivas Niranj; Yardimci, Galip Gürkan; Erdogan, Ozgün; Roach, Jeffrey; Carter, Charles W.

2013-01-01

We tested the idea that ancestral class I and II aminoacyl-tRNA synthetases arose on opposite strands of the same gene. We assembled excerpted 94-residue Urgenes for class I tryptophanyl-tRNA synthetase (TrpRS) and class II Histidyl-tRNA synthetase (HisRS) from a diverse group of species, by identifying and catenating three blocks coding for secondary structures that position the most highly conserved, active-site residues. The codon middle-base pairing frequency was 0.35 ± 0.0002 in all-by-all sense/antisense alignments for 211 TrpRS and 207 HisRS sequences, compared with frequencies between 0.22 ± 0.0009 and 0.27 ± 0.0005 for eight different representations of the null hypothesis. Clustering algorithms demonstrate further that profiles of middle-base pairing in the synthetase antisense alignments are correlated along the sequences from one species-pair to another, whereas this is not the case for similar operations on sets representing the null hypothesis. Most probable reconstructed sequences for ancestral nodes of maximum likelihood trees show that middle-base pairing frequency increases to approximately 0.42 ± 0.002 as bacterial trees approach their roots; ancestral nodes from trees including archaeal sequences show a less pronounced increase. Thus, contemporary and reconstructed sequences all validate important bioinformatic predictions based on descent from opposite strands of the same ancestral gene. They further provide novel evidence for the hypothesis that bacteria lie closer than archaea to the origin of translation. Moreover, the inverse polarity of genetic coding, together with a priori α-helix propensities suggest that in-frame coding on opposite strands leads to similar secondary structures with opposite polarity, as observed in TrpRS and HisRS crystal structures. PMID:23576570

Transonic Drag Prediction on a DLR-F6 Transport Configuration Using Unstructured Grid Solvers

NASA Technical Reports Server (NTRS)

Lee-Rausch, E. M.; Frink, N. T.; Mavriplis, D. J.; Rausch, R. D.; Milholen, W. E.

2004-01-01

A second international AIAA Drag Prediction Workshop (DPW-II) was organized and held in Orlando Florida on June 21-22, 2003. The primary purpose was to inves- tigate the code-to-code uncertainty. address the sensitivity of the drag prediction to grid size and quantify the uncertainty in predicting nacelle/pylon drag increments at a transonic cruise condition. This paper presents an in-depth analysis of the DPW-II computational results from three state-of-the-art unstructured grid Navier-Stokes flow solvers exercised on similar families of tetrahedral grids. The flow solvers are USM3D - a tetrahedral cell-centered upwind solver. FUN3D - a tetrahedral node-centered upwind solver, and NSU3D - a general element node-centered central-differenced solver. For the wingbody, the total drag predicted for a constant-lift transonic cruise condition showed a decrease in code-to-code variation with grid refinement as expected. For the same flight condition, the wing/body/nacelle/pylon total drag and the nacelle/pylon drag increment predicted showed an increase in code-to-code variation with grid refinement. Although the range in total drag for the wingbody fine grids was only 5 counts, a code-to-code comparison of surface pressures and surface restricted streamlines indicated that the three solvers were not all converging to the same flow solutions- different shock locations and separation patterns were evident. Similarly, the wing/body/nacelle/pylon solutions did not appear to be converging to the same flow solutions. Overall, grid refinement did not consistently improve the correlation with experimental data for either the wingbody or the wing/body/nacelle pylon configuration. Although the absolute values of total drag predicted by two of the solvers for the medium and fine grids did not compare well with the experiment, the incremental drag predictions were within plus or minus 3 counts of the experimental data. The correlation with experimental incremental drag was not significantly changed by specifying transition. Although the sources of code-to-code variation in force and moment predictions for the three unstructured grid codes have not yet been identified, the current study reinforces the necessity of applying multiple codes to the same application to assess uncertainty.

Role of Amines in Adhesion of Polybutadiene to Glass Substrates. II. Reactions of Amines with Triethylsilanol and/or Fumed Silica.

DTIC Science & Technology

1982-10-01

Schmidt I Dr. F. Roberto 1 Assistant Secretary of the Navy Code AFRPL MKPA (RE, and S) Room SE 731 Edwards AFE, CA 93523 Pentagon Washington, D.C...Force Office of’Sctentific Office of Naval Research Research odie 43 vDirectorate of Chemical Sciences CodeA l V 22217 " Bolling Air Force Base Arlington

The association between patient-therapist MATRIX congruence and treatment outcome.

PubMed

Mendlovic, Shlomo; Saad, Amit; Roll, Uri; Ben Yehuda, Ariel; Tuval-Mashiah, Rivka; Atzil-Slonim, Dana

2018-03-14

The present study aimed to examine the association between patient-therapist micro-level congruence/incongruence ratio and psychotherapeutic outcome. Nine good- and nine poor-outcome psychodynamic treatments (segregated by comparing pre- and post-treatment BDI-II) were analyzed (N = 18) moment by moment using the MATRIX (total number of MATRIX codes analyzed = 11,125). MATRIX congruence was defined as similar adjacent MATRIX codes. the congruence/incongruence ratio tended to increase as the treatment progressed only in good-outcome treatments. Progression of MATRIX codes' congruence/incongruence ratio is associated with good outcome of psychotherapy.

A Parameter Study for Modeling Mg ii h and k Emission during Solar Flares

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rubio da Costa, Fatima; Kleint, Lucia, E-mail: frubio@stanford.edu

2017-06-20

Solar flares show highly unusual spectra in which the thermodynamic conditions of the solar atmosphere are encoded. Current models are unable to fully reproduce the spectroscopic flare observations, especially the single-peaked spectral profiles of the Mg ii h and k lines. We aim to understand the formation of the chromospheric and optically thick Mg ii h and k lines in flares through radiative transfer calculations. We take a flare atmosphere obtained from a simulation with the radiative hydrodynamic code RADYN as input for a radiative transfer modeling with the RH code. By iteratively changing this model atmosphere and varying thermodynamicmore » parameters such as temperature, electron density, and velocity, we study their effects on the emergent intensity spectra. We reproduce the typical single-peaked Mg ii h and k flare spectral shape and approximate the intensity ratios to the subordinate Mg ii lines by increasing either densities, temperatures, or velocities at the line core formation height range. Additionally, by combining unresolved upflows and downflows up to ∼250 km s{sup −1} within one resolution element, we reproduce the widely broadened line wings. While we cannot unambiguously determine which mechanism dominates in flares, future modeling efforts should investigate unresolved components, additional heat dissipation, larger velocities, and higher densities and combine the analysis of multiple spectral lines.« less

The HART II International Workshop: An Assessment of the State-of-the-Art in Comprehensive Code Prediction

NASA Technical Reports Server (NTRS)

vanderWall, Berend G.; Lim, Joon W.; Smith, Marilyn J.; Jung, Sung N.; Bailly, Joelle; Baeder, James D.; Boyd, D. Douglas, Jr.

2013-01-01

Significant advancements in computational fluid dynamics (CFD) and their coupling with computational structural dynamics (CSD, or comprehensive codes) for rotorcraft applications have been achieved recently. Despite this, CSD codes with their engineering level of modeling the rotor blade dynamics, the unsteady sectional aerodynamics and the vortical wake are still the workhorse for the majority of applications. This is especially true when a large number of parameter variations is to be performed and their impact on performance, structural loads, vibration and noise is to be judged in an approximate yet reliable and as accurate as possible manner. In this article, the capabilities of such codes are evaluated using the HART II International Workshop database, focusing on a typical descent operating condition which includes strong blade-vortex interactions. A companion article addresses the CFD/CSD coupled approach. Three cases are of interest: the baseline case and two cases with 3/rev higher harmonic blade root pitch control (HHC) with different control phases employed. One setting is for minimum blade-vortex interaction noise radiation and the other one for minimum vibration generation. The challenge is to correctly predict the wake physics-especially for the cases with HHC-and all the dynamics, aerodynamics, modifications of the wake structure and the aero-acoustics coming with it. It is observed that the comprehensive codes used today have a surprisingly good predictive capability when they appropriately account for all of the physics involved. The minimum requirements to obtain these results are outlined.

An Assessment of Comprehensive Code Prediction State-of-the-Art Using the HART II International Workshop Data

NASA Technical Reports Server (NTRS)

vanderWall, Berend G.; Lim, Joon W.; Smith, Marilyn J.; Jung, Sung N.; Bailly, Joelle; Baeder, James D.; Boyd, D. Douglas, Jr.

2012-01-01

Despite significant advancements in computational fluid dynamics and their coupling with computational structural dynamics (= CSD, or comprehensive codes) for rotorcraft applications, CSD codes with their engineering level of modeling the rotor blade dynamics, the unsteady sectional aerodynamics and the vortical wake are still the workhorse for the majority of applications. This is especially true when a large number of parameter variations is to be performed and their impact on performance, structural loads, vibration and noise is to be judged in an approximate yet reliable and as accurate as possible manner. In this paper, the capabilities of such codes are evaluated using the HART II Inter- national Workshop data base, focusing on a typical descent operating condition which includes strong blade-vortex interactions. Three cases are of interest: the baseline case and two cases with 3/rev higher harmonic blade root pitch control (HHC) with different control phases employed. One setting is for minimum blade-vortex interaction noise radiation and the other one for minimum vibration generation. The challenge is to correctly predict the wake physics - especially for the cases with HHC - and all the dynamics, aerodynamics, modifications of the wake structure and the aero-acoustics coming with it. It is observed that the comprehensive codes used today have a surprisingly good predictive capability when they appropriately account for all of the physics involved. The minimum requirements to obtain these results are outlined.

15 CFR 922.134 - Notification and review.

Code of Federal Regulations, 2010 CFR

2010-01-01

... MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Monterey Bay National Marine Sanctuary § 922.134... State of California under section 13377 of the California Water Code; and (ii) Waste Discharge...

15 CFR 922.134 - Notification and review.

Code of Federal Regulations, 2011 CFR

2011-01-01

... MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Monterey Bay National Marine Sanctuary § 922.134... State of California under section 13377 of the California Water Code; and (ii) Waste Discharge...

FAST INVERSION OF SOLAR Ca II SPECTRA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beck, C.; Choudhary, D. P.; Rezaei, R.

We present a fast (<<1 s per profile) inversion code for solar Ca II lines. The code uses an archive of spectra that are synthesized prior to the inversion under the assumption of local thermodynamic equilibrium (LTE). We show that it can be successfully applied to spectrograph data or more sparsely sampled spectra from two-dimensional spectrometers. From a comparison to a non-LTE inversion of the same set of spectra, we derive a first-order non-LTE correction to the temperature stratifications derived in the LTE approach. The correction factor is close to unity up to log τ ∼ –3 and increases to valuesmore » of 2.5 and 4 at log τ = –6 in the quiet Sun and the umbra, respectively.« less

Expression in Escherichia coli and characterization of a recombinant 7Fe ferredoxin of Rhodobacter capsulatus.

PubMed Central

Jouanneau, Y; Duport, C; Meyer, C; Gaillard, J

1992-01-01

The 7Fe ferredoxin of Rhodobacter capsulatus (FdII) could be expressed in Escherichia coli by cloning the fdxA gene coding for FdII downstream from the lac promoter. The expressed recombinant ferredoxin appeared as a brown protein which was specifically recognized in E. coli cell-free extracts by anti-FdII serum. The purified recombinant ferredoxin was indistinguishable from R. capsulatus FdII on the basis of its molecular, redox and spectroscopic properties. These results indicate that the [3Fe-4S] and [4Fe-4S] clusters were correctly inserted into the recombinant ferredoxin. Images Fig. 2. PMID:1325780

133. ARAII SL1 burial ground. Shows gravel path from ARAII ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

133. ARA-II SL-1 burial ground. Shows gravel path from ARA-II compound to the burial ground, detail of security fence and entry gate, and sign "Danger radiation hazard." F. C. Torkelson Company 842-area-101-1. Date: October 1961. Ineel index code no. 059-0101-00-851-150723. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

Literacy and Deaf Students in Taiwan: Issues, Practices and Directions for Future Research--Part II

ERIC Educational Resources Information Center

Liu, Hsiu Tan; Andrews, Jean F.; Liu, Chun Jung

2014-01-01

In Part I, we underscore the issues surrounding young deaf and hard of hearing (DHH) learners of literacy in Taiwan who use sign to support their learning of Chinese literacy. We also described the linguistic features of Chinese writing and the visual codes used by DHH children. In Part II, we describe the reading and writing practices used with…

Sequences of 95 human MHC haplotypes reveal extreme coding variation in genes other than highly polymorphic HLA class I and II

PubMed Central

Norman, Paul J.; Norberg, Steven J.; Guethlein, Lisbeth A.; Nemat-Gorgani, Neda; Royce, Thomas; Wroblewski, Emily E.; Dunn, Tamsen; Mann, Tobias; Alicata, Claudia; Hollenbach, Jill A.; Chang, Weihua; Shults Won, Melissa; Gunderson, Kevin L.; Abi-Rached, Laurent; Ronaghi, Mostafa; Parham, Peter

2017-01-01

The most polymorphic part of the human genome, the MHC, encodes over 160 proteins of diverse function. Half of them, including the HLA class I and II genes, are directly involved in immune responses. Consequently, the MHC region strongly associates with numerous diseases and clinical therapies. Notoriously, the MHC region has been intractable to high-throughput analysis at complete sequence resolution, and current reference haplotypes are inadequate for large-scale studies. To address these challenges, we developed a method that specifically captures and sequences the 4.8-Mbp MHC region from genomic DNA. For 95 MHC homozygous cell lines we assembled, de novo, a set of high-fidelity contigs and a sequence scaffold, representing a mean 98% of the target region. Included are six alternative MHC reference sequences of the human genome that we completed and refined. Characterization of the sequence and structural diversity of the MHC region shows the approach accurately determines the sequences of the highly polymorphic HLA class I and HLA class II genes and the complex structural diversity of complement factor C4A/C4B. It has also uncovered extensive and unexpected diversity in other MHC genes; an example is MUC22, which encodes a lung mucin and exhibits more coding sequence alleles than any HLA class I or II gene studied here. More than 60% of the coding sequence alleles analyzed were previously uncharacterized. We have created a substantial database of robust reference MHC haplotype sequences that will enable future population scale studies of this complicated and clinically important region of the human genome. PMID:28360230

Experimental Products Development Team (EPDT) Supporting New AWIPS . Part 2; Capabilities

NASA Technical Reports Server (NTRS)

Burks, Jason E.

2015-01-01

In 2012, the Experimental Products Development Team (EPDT) was formed within NASA's Short-term Prediction Research and Transition (SPoRT) Center to create training for development of plug-ins to extend the National Weather Service (NWS) Advanced Weather Interactive Processing System (AWIPS) version 2. The broader atmospheric science community had a need for AWIPS II development training being created at SPoRT and EPDT was expanded to include other groups who were looking for training. Since the expansion of the group occurred, EPDT has provided AWIPS II development training to over thirty participants spanning a wide variety of groups such as NWS Systems Engineering Center, NWS Meteorological Development Laboratory, and several NOAA Cooperative Institutes. Participants within EPDT solidify their learning experience through hands-on learning and by participating in a "code-sprint" in which they troubleshoot existing and develop plug-ins. The hands-on learning workshop is instructor lead with participants completing exercises within the AWIPS II Development Environment. During the code sprints EPDT groups work on projects important to the community and have worked on various plug-ins such as an RGB image recipe creation tool, and an mPing (crowd sourced precipitation type reporting system) ingest and display. EPDT has developed a well-defined training regime which prepares participants to fully develop plug-ins for the extendible AWIPS II architecture from ingest to the display of new data. SPoRT has hosted 2 learning workshops and 1 code sprint over the last two years, and continues to build and shape the EPDT group based on feedback from previous workshops. The presentation will provide an overview of EPDT current and future activities, and best practices developed within EPDT.

Translating an AI application from Lisp to Ada: A case study

NASA Technical Reports Server (NTRS)

Davis, Gloria J.

1991-01-01

A set of benchmarks was developed to test the performance of a newly designed computer executing both Lisp and Ada. Among these was AutoClassII -- a large Artificial Intelligence (AI) application written in Common Lisp. The extraction of a representative subset of this complex application was aided by a Lisp Code Analyzer (LCA). The LCA enabled rapid analysis of the code, putting it in a concise and functionally readable form. An equivalent benchmark was created in Ada through manual translation of the Lisp version. A comparison of the execution results of both programs across a variety of compiler-machine combinations indicate that line-by-line translation coupled with analysis of the initial code can produce relatively efficient and reusable target code.

Radiation Coupling with the FUN3D Unstructured-Grid CFD Code

NASA Technical Reports Server (NTRS)

Wood, William A.

2012-01-01

The HARA radiation code is fully-coupled to the FUN3D unstructured-grid CFD code for the purpose of simulating high-energy hypersonic flows. The radiation energy source terms and surface heat transfer, under the tangent slab approximation, are included within the fluid dynamic ow solver. The Fire II flight test, at the Mach-31 1643-second trajectory point, is used as a demonstration case. Comparisons are made with an existing structured-grid capability, the LAURA/HARA coupling. The radiative surface heat transfer rates from the present approach match the benchmark values within 6%. Although radiation coupling is the focus of the present work, convective surface heat transfer rates are also reported, and are seen to vary depending upon the choice of mesh connectivity and FUN3D ux reconstruction algorithm. On a tetrahedral-element mesh the convective heating matches the benchmark at the stagnation point, but under-predicts by 15% on the Fire II shoulder. Conversely, on a mixed-element mesh the convective heating over-predicts at the stagnation point by 20%, but matches the benchmark away from the stagnation region.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simonen, F.A.; Johnson, K.I.; Liebetrau, A.M.

The VISA-II (Vessel Integrity Simulation Analysis code was originally developed as part of the NRC staff evaluation of pressurized thermal shock. VISA-II uses Monte Carlo simulation to evaluate the failure probability of a pressurized water reactor (PWR) pressure vessel subjected to a pressure and thermal transient specified by the user. Linear elastic fracture mechanics methods are used to model crack initiation and propagation. Parameters for initial crack size and location, copper content, initial reference temperature of the nil-ductility transition, fluence, crack-initiation fracture toughness, and arrest fracture toughness are treated as random variables. This report documents an upgraded version of themore » original VISA code as described in NUREG/CR-3384. Improvements include a treatment of cladding effects, a more general simulation of flaw size, shape and location, a simulation of inservice inspection, an updated simulation of the reference temperature of the nil-ductility transition, and treatment of vessels with multiple welds and initial flaws. The code has been extensively tested and verified and is written in FORTRAN for ease of installation on different computers. 38 refs., 25 figs.« less

Histochemical changes of occlusal surface enamel of permanent teeth, where dental caries is questionable vs sound enamel surfaces.

PubMed

Michalaki, M; Oulis, C J; Pandis, N; Eliades, G

2016-12-01

This in vitro study was to classify questionable for caries occlusal surfaces (QCOS) of permanent teeth according to ICDAS codes 1, 2, and 3 and to compare them in terms of enamel mineral composition with the areas of sound tissue of the same tooth. Partially impacted human molars (60) extracted for therapeutic reasons with QCOS were used in the study, photographed via a polarised light microscope and classified according to the ICDAS II (into codes 1, 2, or 3). The crowns were embedded in clear self-cured acrylic resin and longitudinally sectioned at the levels of the characterised lesions and studied by SEM/EDX, to assess enamel mineral composition of the QCOS. Univariate and multivariate random effect regressions were used for Ca (wt%), P (wt%), and Ca/P (wt%). The EDX analysis indicated changes in the Ca and P contents that were more prominent in ICDAS-II code 3 lesions compared to codes 1 and 2 lesions. In these lesions, Ca (wt%) and P (wt%) concentrations were significantly decreased (p = 0.01) in comparison with sound areas. Ca and P (wt%) contents were significantly lower (p = 0.02 and p = 0.01 respectively) for code 3 areas in comparison with codes 1 and 2 areas. Significantly higher (p = 0.01) Ca (wt%) and P (wt%) contents were found on sound areas compared to the lesion areas. The enamel of occlusal surfaces of permanent teeth with ICDAS 1, 2, and 3 lesions was found to have different Ca/P compositions, necessitating further investigation on whether these altered surfaces might behave differently on etching preparation before fissure sealant placement, compared to sound surfaces.

LSENS, A General Chemical Kinetics and Sensitivity Analysis Code for Homogeneous Gas-Phase Reactions. Part 2; Code Description and Usage

NASA Technical Reports Server (NTRS)

Radhakrishnan, Krishnan; Bittker, David A.

1994-01-01

LSENS, the Lewis General Chemical Kinetics and Sensitivity Analysis Code, has been developed for solving complex, homogeneous, gas-phase chemical kinetics problems and contains sensitivity analysis for a variety of problems, including nonisothermal situations. This report is part II of a series of three reference publications that describe LSENS, provide a detailed guide to its usage, and present many example problems. Part II describes the code, how to modify it, and its usage, including preparation of the problem data file required to execute LSENS. Code usage is illustrated by several example problems, which further explain preparation of the problem data file and show how to obtain desired accuracy in the computed results. LSENS is a flexible, convenient, accurate, and efficient solver for chemical reaction problems such as static system; steady, one-dimensional, inviscid flow; reaction behind incident shock wave, including boundary layer correction; and perfectly stirred (highly backmixed) reactor. In addition, the chemical equilibrium state can be computed for the following assigned states: temperature and pressure, enthalpy and pressure, temperature and volume, and internal energy and volume. For static problems the code computes the sensitivity coefficients of the dependent variables and their temporal derivatives with respect to the initial values of the dependent variables and/or the three rate coefficient parameters of the chemical reactions. Part I (NASA RP-1328) derives the governing equations and describes the numerical solution procedures for the types of problems that can be solved by LSENS. Part III (NASA RP-1330) explains the kinetics and kinetics-plus-sensitivity-analysis problems supplied with LSENS and presents sample results.

NRL Review for 1993

DTIC Science & Technology

1993-05-01

RESEARCH Code 1001 Dr. T. Coffey ASSOCIATE DIRECTORS OF RESEARCH OFFICE FOR STRATEGIC PLANNING Code 1003 Or W.M Tolles II I I/.... I BUSINESS GENERAL...of its strategic vision, we agreed that together towards NRL’s strength lies in its broad, multi- the best solution. " disciplinary character and the...peace, crisis or war, American leaders can continue to contribute in several have always turned to the Sea Services areas as America’s corporate

COM-GEOM Interactive Display Debugger (CIDD)

DTIC Science & Technology

1984-08-01

necessery and Identify by block nlum.ber) Target Description GIFT interactive Computer Graphics SolIi d Geone t ry Combintatorial Gecometry * COM-GLOM 120...program was written to speed up the process of formulating the Com-Geom data used by the Geometric Information for Targets ( GIFT ) 1,2 computer code...Polyhedron Lawrence W. Bain, Mathew J. Reisinger, "The GIFT Code User Manual; Volume I, Introduction and Input Requirements (u)," BRL Report No. 1802

Integrated AUTODIN System Architecture Report. Part 2.

DTIC Science & Technology

1979-03-01

Link Modes Protocols and end-to- end host protocols Codes ASCII, ITA#2 ASCII, Others (Trans- parent to network) Speeds 45 thru 4800 bps 110 bps thru 56K ...service facilities such as AMPEs, subscriber access lines, modems , multiplexers, concentrators, interface development to include software design and...Protocol) CODES - ASCII and ITA#2 (others transparent) SPEEDS - 45.5bps - 56K bps FORMATS - AUTODIN II Segment Formats, JANAP 128, ACP 126/127, DOI 103

Structural basis of peptide recognition by the angiotensin-1 converting enzyme homologue AnCE from Drosophila melanogaster

PubMed Central

Akif, Mohd; Masuyer, Geoffrey; Bingham, Richard J; Sturrock, Edward D; Isaac, R Elwyn; Acharya, K Ravi

2012-01-01

Human somatic angiotensin-1 converting enzyme (ACE) is a zinc-dependent exopeptidase, that catalyses the conversion of the decapeptide angiotensin I to the octapeptide angiotensin II, by removing a C-terminal dipeptide. It is the principal component of the renin-angiotensin–aldosterone system that regulates blood pressure. Hence it is an important therapeutic target for the treatment of hypertension and cardiovascular disorders. Here, we report the structures of an ACE homologue from Drosophila melanogaster (AnCE; a proven structural model for the more complex human ACE) co-crystallized with mammalian peptide substrates (bradykinin, Thr6–bradykinin, angiotensin I and a snake venom peptide inhibitor, bradykinin-potentiating peptide-b). The structures determined at 2-Å resolution illustrate that both angiotensin II (the cleaved product of angiotensin I by AnCE) and bradykinin-potentiating peptide-b bind in an analogous fashion at the active site of AnCE, but also exhibit significant differences. In addition, the binding of Arg–Pro–Pro, the cleavage product of bradykinin and Thr6– bradykinin, provides additional detail of the general peptide binding in AnCE. Thus the new structures of AnCE complexes presented here improves our understanding of the binding of peptides and the mechanism by which peptides inhibit this family of enzymes. Database The atomic coordinates and structure factors for AnCE–Ang II (code 4AA1), AnCE–BPPb (code 4AA2), AnCE–BK (code 4ASQ) and AnCE–Thr6–BK (code 4ASR) complexes have been deposited in the Protein Data Bank, Research Collaboratory for Structural Bioinformatics, Rutgers University, New Brunswick, NJ (http://www.rcsb.org/) Structured digital abstract AnCE cleaves Ang I by enzymatic study (View interaction) Bradykinin and AnCE bind by x-ray crystallography (View interaction) BPP and AnCE bind by x-ray crystallography (View interaction) AnCE cleaves Bradykinin by enzymatic study (View interaction) Ang II and AnCE bind by x-ray crystallography (View interaction) PMID:23082758

Assessing 1D Atmospheric Solar Radiative Transfer Models: Interpretation and Handling of Unresolved Clouds.

NASA Astrophysics Data System (ADS)

Barker, H. W.; Stephens, G. L.; Partain, P. T.; Bergman, J. W.; Bonnel, B.; Campana, K.; Clothiaux, E. E.; Clough, S.; Cusack, S.; Delamere, J.; Edwards, J.; Evans, K. F.; Fouquart, Y.; Freidenreich, S.; Galin, V.; Hou, Y.; Kato, S.; Li, J.;  Mlawer, E.;  Morcrette, J.-J.;  O'Hirok, W.;  Räisänen, P.;  Ramaswamy, V.;  Ritter, B.;  Rozanov, E.;  Schlesinger, M.;  Shibata, K.;  Sporyshev, P.;  Sun, Z.;  Wendisch, M.;  Wood, N.;  Yang, F.

2003-08-01

The primary purpose of this study is to assess the performance of 1D solar radiative transfer codes that are used currently both for research and in weather and climate models. Emphasis is on interpretation and handling of unresolved clouds. Answers are sought to the following questions: (i) How well do 1D solar codes interpret and handle columns of information pertaining to partly cloudy atmospheres? (ii) Regardless of the adequacy of their assumptions about unresolved clouds, do 1D solar codes perform as intended?One clear-sky and two plane-parallel, homogeneous (PPH) overcast cloud cases serve to elucidate 1D model differences due to varying treatments of gaseous transmittances, cloud optical properties, and basic radiative transfer. The remaining four cases involve 3D distributions of cloud water and water vapor as simulated by cloud-resolving models. Results for 25 1D codes, which included two line-by-line (LBL) models (clear and overcast only) and four 3D Monte Carlo (MC) photon transport algorithms, were submitted by 22 groups. Benchmark, domain-averaged irradiance profiles were computed by the MC codes. For the clear and overcast cases, all MC estimates of top-of-atmosphere albedo, atmospheric absorptance, and surface absorptance agree with one of the LBL codes to within ±2%. Most 1D codes underestimate atmospheric absorptance by typically 15-25 W m-2 at overhead sun for the standard tropical atmosphere regardless of clouds.Depending on assumptions about unresolved clouds, the 1D codes were partitioned into four genres: (i) horizontal variability, (ii) exact overlap of PPH clouds, (iii) maximum/random overlap of PPH clouds, and (iv) random overlap of PPH clouds. A single MC code was used to establish conditional benchmarks applicable to each genre, and all MC codes were used to establish the full 3D benchmarks. There is a tendency for 1D codes to cluster near their respective conditional benchmarks, though intragenre variances typically exceed those for the clear and overcast cases. The majority of 1D codes fall into the extreme category of maximum/random overlap of PPH clouds and thus generally disagree with full 3D benchmark values. Given the fairly limited scope of these tests and the inability of any one code to perform extremely well for all cases begs the question that a paradigm shift is due for modeling 1D solar fluxes for cloudy atmospheres.

Definition of RNA Polymerase II CoTC Terminator Elements in the Human Genome

PubMed Central

Nojima, Takayuki; Dienstbier, Martin; Murphy, Shona; Proudfoot, Nicholas J.; Dye, Michael J.

2013-01-01

Summary Mammalian RNA polymerase II (Pol II) transcription termination is an essential step in protein-coding gene expression that is mediated by pre-mRNA processing activities and DNA-encoded terminator elements. Although much is known about the role of pre-mRNA processing in termination, our understanding of the characteristics and generality of terminator elements is limited. Whereas promoter databases list up to 40,000 known and potential Pol II promoter sequences, fewer than ten Pol II terminator sequences have been described. Using our knowledge of the human β-globin terminator mechanism, we have developed a selection strategy for mapping mammalian Pol II terminator elements. We report the identification of 78 cotranscriptional cleavage (CoTC)-type terminator elements at endogenous gene loci. The results of this analysis pave the way for the full understanding of Pol II termination pathways and their roles in gene expression. PMID:23562152

14 CFR 257.6 - Effective and compliance dates.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the selling carrier is not the transporting carrier and (ii) Of the transporting carrier's identity... transportation involving a code-share arrangement of the transporting carrier's corporate name and any other name...

14 CFR 257.6 - Effective and compliance dates.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the selling carrier is not the transporting carrier and (ii) Of the transporting carrier's identity... transportation involving a code-share arrangement of the transporting carrier's corporate name and any other name...

14 CFR 257.6 - Effective and compliance dates.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the selling carrier is not the transporting carrier and (ii) Of the transporting carrier's identity... transportation involving a code-share arrangement of the transporting carrier's corporate name and any other name...

14 CFR 257.6 - Effective and compliance dates.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the selling carrier is not the transporting carrier and (ii) Of the transporting carrier's identity... transportation involving a code-share arrangement of the transporting carrier's corporate name and any other name...

75 FR 53720 - Manufacturer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-01

... Schedule Marihuana (7360) I Tetrahydrocannabinols (7370) I Alphamethadol (9605) I Nabilone (7379) II... controlled substances in bulk for distribution to its customers. In reference to drug code 7360 (Marihuana...

49 CFR 236.909 - Minimum performance standard.

Code of Federal Regulations, 2010 CFR

2010-10-01

...://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html; (ii) The product is... exposure must be expressed as total train miles traveled per year over the relevant railroad infrastructure...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This volume contains appendices for the following: Rocky Flats Plant and Idaho National Engineering Laboratory waste process information; TRUPACT-II content codes (TRUCON); TRUPACT-II chemical list; chemical compatibility analysis for Rocky Flats Plant waste forms; chemical compatibility analysis for waste forms across all sites; TRU mixed waste characterization database; hazardous constituents of Rocky Flats Transuranic waste; summary of waste components in TRU waste sampling program at INEL; TRU waste sampling program; and waste analysis data.

Flight Attendant Fatigue Recommendation 2: Flight Attendant Work/Rest Patterns, Alertness, and Performance Assessment

DTIC Science & Technology

2010-12-01

Recommendation II: Flight Attendant Work/Rest Patterns, Alertness, and Performance Assessment DOT/FAA/AM-10/22 Office of Aerospace Medicine Washington, DC...Recipient’s Catalog No. DOT/FAA/AM-10/22 4. Title and Subtitle 5. Report Date December 2010 6. Performing Organization Code Flight...Attendant Fatigue Recommendation II: Flight Attendant Work/Rest Patterns, Alertness, and Performance Assessment 7. Author(s) 8. Performing

136. ARRII Plot plan as it appeared in 1980, when ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

136. ARR-II Plot plan as it appeared in 1980, when interior modifications were being prepared to remodel electrical apparatus in ARA-602 in connection with use as a research and development joining laboratory. EG&G, Idaho, Inc. 1570-ARA-II-100-1. Date: April 1980. Ineel index code no. 070-0199-00-220-159749. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

Optimization of Supercomputer Use on EADS II System

NASA Technical Reports Server (NTRS)

Ahmed, Ardsher

1998-01-01

The main objective of this research was to optimize supercomputer use to achieve better throughput and utilization of supercomputers and to help facilitate the movement of non-supercomputing (inappropriate for supercomputer) codes to mid-range systems for better use of Government resources at Marshall Space Flight Center (MSFC). This work involved the survey of architectures available on EADS II and monitoring customer (user) applications running on a CRAY T90 system.

38 CFR 3.43 - Burial benefits at the full-dollar rate for certain Filipino veterans residing in the United...

Code of Federal Regulations, 2014 CFR

2014-07-01

.... citizenship through birth in the territorial U.S., birth abroad as provided under title 8, United States Code.... passport; (ii) A birth certificate showing that he or she was born in the U.S.; or (iii) A Report of Birth...) Property tax bills and receipts; and (F) School records. (ii) A Post Office box mailing address in the...

38 CFR 3.43 - Burial benefits at the full-dollar rate for certain Filipino veterans residing in the United...

Code of Federal Regulations, 2011 CFR

2011-07-01

.... citizenship through birth in the territorial U.S., birth abroad as provided under title 8, United States Code.... passport; (ii) A birth certificate showing that he or she was born in the U.S.; or (iii) A Report of Birth...) Property tax bills and receipts; and (F) School records. (ii) A Post Office box mailing address in the...

38 CFR 3.43 - Burial benefits at the full-dollar rate for certain Filipino veterans residing in the United...

Code of Federal Regulations, 2013 CFR

2013-07-01

.... citizenship through birth in the territorial U.S., birth abroad as provided under title 8, United States Code.... passport; (ii) A birth certificate showing that he or she was born in the U.S.; or (iii) A Report of Birth...) Property tax bills and receipts; and (F) School records. (ii) A Post Office box mailing address in the...

38 CFR 3.43 - Burial benefits at the full-dollar rate for certain Filipino veterans residing in the United...

Code of Federal Regulations, 2010 CFR

2010-07-01

.... citizenship through birth in the territorial U.S., birth abroad as provided under title 8, United States Code.... passport; (ii) A birth certificate showing that he or she was born in the U.S.; or (iii) A Report of Birth...) Property tax bills and receipts; and (F) School records. (ii) A Post Office box mailing address in the...

38 CFR 3.43 - Burial benefits at the full-dollar rate for certain Filipino veterans residing in the United...

Code of Federal Regulations, 2012 CFR

2012-07-01

.... citizenship through birth in the territorial U.S., birth abroad as provided under title 8, United States Code.... passport; (ii) A birth certificate showing that he or she was born in the U.S.; or (iii) A Report of Birth...) Property tax bills and receipts; and (F) School records. (ii) A Post Office box mailing address in the...

Initial performances of first undulator-based hard x-ray beamlines of NSLS-II compared to simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chubar, Oleg, E-mail: chubar@bnl.gov; Chu, Yong S.; Huang, Xiaojing

2016-07-27

Commissioning of the first X-ray beamlines of NSLS-II included detailed measurements of spectral and spatial distributions of the radiation at different locations of the beamlines, from front-ends to sample positions. Comparison of some of these measurement results with high-accuracy calculations of synchrotron (undulator) emission and wavefront propagation through X-ray transport optics, performed using SRW code, is presented.

TORO II: A finite element computer program for nonlinear quasi-static problems in electromagnetics: Part 2, User`s manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gartling, D.K.

User instructions are given for the finite element, electromagnetics program, TORO II. The theoretical background and numerical methods used in the program are documented in SAND95-2472. The present document also describes a number of example problems that have been analyzed with the code and provides sample input files for typical simulations. 20 refs., 34 figs., 3 tabs.

(NTF) National Transonic Facility Test 213-SFW Flow Control II,

NASA Image and Video Library

2012-11-19

(NTF) National Transonic Facility Test 213-SFW Flow Control II, Fast-MAC Model: The fundamental Aerodynamics Subsonic Transonic-Modular Active Control (Fast-MAC) Model was tested for the 2nd time in the NTF. The objectives were to document the effects of Reynolds numbers on circulation control aerodynamics and to develop and open data set for CFD code validation. Image taken in building 1236, National Transonic Facility

A Tandemly Arranged Pattern of Two 5S rDNA Arrays in Amolops mantzorum (Anura, Ranidae).

PubMed

Liu, Ting; Song, Menghuan; Xia, Yun; Zeng, Xiaomao

2017-01-01

In an attempt to extend the knowledge of the 5S rDNA organization in anurans, the 5S rDNA sequences of Amolops mantzorum were isolated, characterized, and mapped by FISH. Two forms of 5S rDNA, type I (209 bp) and type II (about 870 bp), were found in specimens investigated from various populations. Both of them contained a 118-bp coding sequence, readily differentiated by their non-transcribed spacer (NTS) sizes and compositions. Four probes (the 5S rDNA coding sequences, the type I NTS, the type II NTS, and the entire type II 5S rDNA sequences) were respectively labeled with TAMRA or digoxigenin to hybridize with mitotic chromosomes for samples of all localities. It turned out that all probes showed the same signals that appeared in every centromeric region and in the telomeric regions of chromosome 5, without differences within or between populations. Obviously, both type I and type II of the 5S rDNA arrays arranged in tandem, which was contrasting with other frogs or fishes recorded to date. More interestingly, all the probes detected centromeric regions in all karyotypes, suggesting the presence of a satellite DNA family derived from 5S rDNA. © 2017 S. Karger AG, Basel.

Type IV pili of Acidithiobacillus ferrooxidans can transfer electrons from extracellular electron donors.

PubMed

Li, Yongquan; Li, Hongyu

2014-03-01

Studies on Acidithiobacillus ferrooxidans accepting electrons from Fe(II) have previously focused on cytochrome c. However, we have discovered that, besides cytochrome c, type IV pili (Tfp) can transfer electrons. Here, we report conduction by Tfp of A. ferrooxidans analyzed with a conducting-probe atomic force microscope (AFM). The results indicate that the Tfp of A. ferrooxidans are highly conductive. The genome sequence of A. ferrooxidans ATCC 23270 contains two genes, pilV and pilW, which code for pilin domain proteins with the conserved amino acids characteristic of Tfp. Multiple alignment analysis of the PilV and PilW (pilin) proteins indicated that pilV is the adhesin gene while pilW codes for the major protein element of Tfp. The likely function of Tfp is to complete the circuit between the cell surface and Fe(II) oxides. These results indicate that Tfp of A. ferrooxidans might serve as biological nanowires transferring electrons from the surface of Fe(II) oxides to the cell surface. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Regular Topologies for Gigabit Wide-Area Networks: Congestion Avoidance Testbed Experiments. Volume 3

NASA Technical Reports Server (NTRS)

Denny, Barbara A.; McKenney, Paul E., Sr.; Lee, Danny

1994-01-01

This document is Volume 3 of the final technical report on the work performed by SRI International (SRI) on SRI Project 8600. The document includes source listings for all software developed by SRI under this effort. Since some of our work involved the use of ST-II and the Sun Microsystems, Inc. (Sun) High-Speed Serial Interface (HSI/S) driver, we have included some of the source developed by LBL and BBN as well. In most cases, our decision to include source developed by other contractors depended on whether it was necessary to modify the original code. If we have modified the software in any way, it is included in this document. In the case of the Traffic Generator (TG), however, we have included all the ST-II software, even though BBN performed the integration, because the ST-II software is part of the standard TG release. It is important to note that all the code developed by other contractors is in the public domain, so that all software developed under this effort can be re-created from the source included here.

BESAFE II: Accident safety analysis code for MFE reactor designs

NASA Astrophysics Data System (ADS)

Sevigny, Lawrence Michael

The viability of controlled thermonuclear fusion as an alternative energy source hinges on its desirability from an economic and an environmental and safety standpoint. It is the latter which is the focus of this thesis. For magnetic fusion energy (MFE) devices, the safety concerns equate to a design's behavior during a worst-case accident scenario which is the loss of coolant accident (LOCA). In this dissertation, we examine the behavior of MFE devices during a LOCA and how this behavior relates to the safety characteristics of the machine; in particular the acute, whole-body, early dose. In doing so, we have produced an accident safety code, BESAFE II, now available to the fusion reactor design community. The Appendix constitutes the User's Manual for BESAFE II. The theory behind early dose calculations including the mobilization of activation products is presented in Chapter 2. Since mobilization of activation products is a strong function of temperature, it becomes necessary to calculate the thermal response of a design during a LOCA in order to determine the fraction of the activation products which are mobilized and thus become the source for the dose. The code BESAFE II is designed to determine the temperature history of each region of a design and determine the resulting mobilization of activation products at each point in time during the LOCA. The BESAFE II methodology is discussed in Chapter 4, followed by demonstrations of its use for two reference design cases: a PCA-Li tokamak and a SiC-He tokamak. Of these two cases, it is shown that the SiC-He tokamak is a better design from an accident safety standpoint than the PCA-Li tokamak. It is also found that doses derived from temperature-dependent mobilization data are different than those predicted using set mobilization categories such as those that involve Piet fractions. This demonstrates the need for more experimental data on fusion materials. The possibility for future improvements and modifications to BESAFE II is discussed in Chapter 6, for example, by adding additional environmental indices such as a waste disposal index. The biggest improvement to BESAFE II would be an increase in the database of activation product mobilization for a larger spectrum of fusion reactor materials. The ultimate goal we have is for BESAFE II to become part of a systems design program which would include economic factors and allow both safety and the cost of electricity to influence design.

PSEUDO-CODEWORD LANDSCAPE

DOE Office of Scientific and Technical Information (OSTI.GOV)

CHERTKOV, MICHAEL; STEPANOV, MIKHAIL

2007-01-10

The authors discuss performance of Low-Density-Parity-Check (LDPC) codes decoded by Linear Programming (LP) decoding at moderate and large Signal-to-Noise-Ratios (SNR). Frame-Error-Rate (FER) dependence on SNR and the noise space landscape of the coding/decoding scheme are analyzed by a combination of the previously introduced instanton/pseudo-codeword-search method and a new 'dendro' trick. To reduce complexity of the LP decoding for a code with high-degree checks, {ge} 5, they introduce its dendro-LDPC counterpart, that is the code performing identifically to the original one under Maximum-A-Posteriori (MAP) decoding but having reduced (down to three) check connectivity degree. Analyzing number of popular LDPC codes andmore » their dendro versions performing over the Additive-White-Gaussian-Noise (AWGN) channel, they observed two qualitatively different regimes: (i) error-floor sets early, at relatively low SNR, and (ii) FER decays with SNR increase faster at moderate SNR than at the largest SNR. They explain these regimes in terms of the pseudo-codeword spectra of the codes.« less

Variability in interhospital trauma data coding and scoring: A challenge to the accuracy of aggregated trauma registries.

PubMed

Arabian, Sandra S; Marcus, Michael; Captain, Kevin; Pomphrey, Michelle; Breeze, Janis; Wolfe, Jennefer; Bugaev, Nikolay; Rabinovici, Reuven

2015-09-01

Analyses of data aggregated in state and national trauma registries provide the platform for clinical, research, development, and quality improvement efforts in trauma systems. However, the interhospital variability and accuracy in data abstraction and coding have not yet been directly evaluated. This multi-institutional, Web-based, anonymous study examines interhospital variability and accuracy in data coding and scoring by registrars. Eighty-two American College of Surgeons (ACS)/state-verified Level I and II trauma centers were invited to determine different data elements including diagnostic, procedure, and Abbreviated Injury Scale (AIS) coding as well as selected National Trauma Data Bank definitions for the same fictitious case. Variability and accuracy in data entries were assessed by the maximal percent agreement among the registrars for the tested data elements, and 95% confidence intervals were computed to compare this level of agreement to the ideal value of 100%. Variability and accuracy in all elements were compared (χ testing) based on Trauma Quality Improvement Program (TQIP) membership, level of trauma center, ACS verification, and registrar's certifications. Fifty registrars (61%) completed the survey. The overall accuracy for all tested elements was 64%. Variability was noted in all examined parameters except for the place of occurrence code in all groups and the lower extremity AIS code in Level II trauma centers and in the Certified Specialist in Trauma Registry- and Certified Abbreviated Injury Scale Specialist-certified registrar groups. No differences in variability were noted when groups were compared based on TQIP membership, level of center, ACS verification, and registrar's certifications, except for prehospital Glasgow Coma Scale (GCS), where TQIP respondents agreed more than non-TQIP centers (p = 0.004). There is variability and inaccuracy in interhospital data coding and scoring of injury information. This finding casts doubt on the validity of registry data used in all aspects of trauma care and injury surveillance.

TRIAD II: do living wills have an impact on pre-hospital lifesaving care?

PubMed

Mirarchi, Ferdinando L; Kalantzis, Stella; Hunter, Daniel; McCracken, Emily; Kisiel, Theresa

2009-02-01

Living wills accompany patients who present for emergent care. To the best of our knowledge, no studies assess pre-hospital provider interpretations of these instructions. Determine how a living will is interpreted and assess how interpretation impacts lifesaving care. Three-part survey administered at a regional emergency medical system educational symposium to 150 emergency medical technicians (EMTs) and paramedics. Part I assessed understanding of the living will and do-not-resuscitate (DNR) orders. Part II assessed the living will's impact in clinical situations of patients requiring lifesaving interventions. Part III was similar to part II except a code status designation (full code) was incorporated into the living will. There were 127 surveys completed, yielding an 87% response rate. The majority were male (55%) and EMTs (74%). The average age was 44 years and the average duration of employment was 15 years. Ninety percent (95% confidence interval [CI] 84.6-95.4%) of respondents determined that, after review of the living will, the patient's code status was DNR, and 92% (95% CI 86.5-96.6%) defined their understanding of DNR as comfort care/end-of-life care. When the living will was applied to clinical situations, it resulted in a higher proportion of patients being classified as DNR as opposed to full code (Case A 78% [95% CI 71.2-85.6%] vs. 22% [95% CI 14.4-28.8%], respectively; Case B 67% [95% CI 58.4-74.9%] vs. 33% [95% CI 25.1-1.6%], respectively; Case C 63% [95% CI 55.1-71.9%] vs. 37% [95% CI 28.1-44.9%]), respectively. With the scenarios presented, this DNR classification resulted in a lack of or a delay in lifesaving interventions. Incorporating a code status into the living will produced statistically significant increases in the provision of lifesaving care. In Case A, intubation increased from 15% to 56% (p < 0.0001); Case B, defibrillation increased from 40% to 59% (p < 0.0001); and Case C, defibrillation increased from 36% to 65% (p < 0.0001). Significant confusion and concern for patient safety exists in the pre-hospital setting due to the understanding and implementation of living wills and DNR orders. This confusion can be corrected by implementing clearly defined code status into the living will.

75 FR 75496 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

... controlled substances listed in schedule I and II: Drug Schedule Marijuana (7360) I Tetrahydrocannabinols... customers for non- clinical, laboratory-based research only. In reference to drug code 7360 (Marijuana), the...

Upgrade of Irradiation Test Capability of the Experimental Fast Reactor Joyo

NASA Astrophysics Data System (ADS)

Sekine, Takashi; Aoyama, Takafumi; Suzuki, Soju; Yamashita, Yoshioki

2003-06-01

The JOYO MK-II core was operated from 1983 to 2000 as fast neutron irradiation bed. In order to meet various requirements for irradiation tests for development of FBRs, the JOYO upgrading project named MK-III program was initiated. The irradiation capability in the MK-III core will be about four times larger than that of the MK-II core. Advanced irradiation test subassemblies such as capsule type subassembly and on-line instrumentation rig are planned. As an innovative reactor safety system, the irradiation test of Self-Actuated Shutdown System (SASS) will be conducted. In order to improve the accuracy of neutron fluence, the core management code system was upgraded, and the Monte Carlo code and Helium Accumulation Fluence Monitor (HAFM) were applied. The MK-III core is planned to achieve initial criticality in July 2003.

Overview of Edge Simulation Laboratory (ESL)

NASA Astrophysics Data System (ADS)

Cohen, R. H.; Dorr, M.; Hittinger, J.; Rognlien, T.; Umansky, M.; Xiong, A.; Xu, X.; Belli, E.; Candy, J.; Snyder, P.; Colella, P.; Martin, D.; Sternberg, T.; van Straalen, B.; Bodi, K.; Krasheninnikov, S.

2006-10-01

The ESL is a new collaboration to build a full-f electromagnetic gyrokinetic code for tokamak edge plasmas using continuum methods. Target applications are edge turbulence and transport (neoclassical and anomalous), and edge-localized modes. Initially the project has three major threads: (i) verification and validation of TEMPEST, the project's initial (electrostatic) edge code which can be run in 4D (neoclassical and transport-timescale applications) or 5D (turbulence); (ii) design of the next generation code, which will include more complete physics (electromagnetics, fluid equation option, improved collisions) and advanced numerics (fully conservative, high-order discretization, mapped multiblock grids, adaptivity), and (iii) rapid-prototype codes to explore the issues attached to solving fully nonlinear gyrokinetics with steep radial gradiens. We present a brief summary of the status of each of these activities.

The POPOP4 library and codes for preparing secondary gamma-ray production cross sections

NASA Technical Reports Server (NTRS)

Ford, W. E., III

1972-01-01

The POPOP4 code for converting secondary gamma ray yield data to multigroup secondary gamma ray production cross sections and the POPOP4 library of secondary gamma ray yield data are described. Recent results of the testing of uranium and iron data sets from the POPOP4 library are given. The data sets were tested by comparing calculated secondary gamma ray pulse height spectra measured at the ORNL TSR-II reactor.

Impact of the implementation of the Infarction Code strategy in patients with acute myocardial infarction diagnosis in the Hospital de Cardiología of the Centro Médico Nacional Siglo XXI

PubMed

Sánchez, Gabriela Borrayo; Covarrubias, Héctor Álvarez; Rodríguez, Gilberto Pérez; Uribe, Efraín Arizmendi; Ramírez-Arias, Erick; Peralta, Martín Rosas; Dávila, Jesús Arriaga

2017-01-01

To evaluate the impact of the implementation of the Infarction Code strategy in patients with acute myocardial infarction diagnosis. Consecutive patients with ST-elevation acute myocardial infarction ≤12 hours of evolution, were included in the infarction code strategy, before (Group I) and after (Group II). Times of medical attention and major cardiovascular events during hospitalization were analyzed. 1227 patients were included, 919 men (75%) and 308 women (25%) with an average age of 62 ± 11 years. Among Group I and Group II, percutaneous coronary intervention reperfusion therapy changed (16.6% to 42.6%), fibrinolytic therapy (39.3% to 25%), and patients who did not receive any form of reperfusion therapy (44% to 32.6%; p < 0.0001). Times of medical attention decreased significantly (door-to-needle time decreased from 92 to 72 minutes, p = 0.004; door-to-balloon time decreased from 140 to 92 minutes, p < 0.0001). Kidney failure (24.6% vs. 17.9%; p = 0.006), major complications (35.3% to 29.3%), and death (21% vs. 12%; odds ratio: 0.52; 95% confidence interval: 0.38-0.71; p = 0.004). also decreased. The Infarction Code strategy improved treatment, times of medical attention and decreased complications and death in these patients.

Preliminary Modelling of Radiation Levels at the Fermilab PIP-II Linac

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lari, L.; Cerutti, F.; Esposito, L. S.

PIP-II is the Fermilab's flagship project for providing powerful, high-intensity proton beams to the laboratory's experiments. The heart of PIP-II is an 800-MeV superconducting linac accelerator. It will be located in a new tunnel with new service buildings and connected to the present Booster through a new transfer line. To support the design of civil engineering and mechanical integration, this paper provides preliminary estimation of radiation level in the gallery at an operational beam loss limit of 0.1 W/m, by means of Monte Carlo calculations with FLUKA and MARS15 codes.

Epidemiological Study of Mild Tramautic Brain Injury Sequelae Cause by Blast Exposure During Operations Iraqi Freedom and Enduring Freedom

DTIC Science & Technology

2012-10-01

Principal Investigator September, 2008 20 (see: VCU sub- award) David X. Cifu, MD Co-Investigator September, 2008 5 (VCU sub-award) Jessica...proven reliability: Wechsler Test of Adult Reading (WTAR, pre- morbid IQ estimate),(Mathias, Bowden, Bigler, & Rosenfeld, 2007) Conners Continuous...II (CVLT-II) (learning and working memory),(Vanderploeg et al., 2005) Wechsler Adult Intelligence Scale III (WAIS-III) items: Digit Symbol Coding

Spectroscopic classification of ASASSN-17je (=AT 2017ffq) as a Type II Supernova

NASA Astrophysics Data System (ADS)

Rodriguez, Osmar; Prieto, J. L.

2017-07-01

We obtained an optical spectrum (450-760nm) of ASASSN-17je/AT2017ffq (ATel #10571) on 2017 July 15.19 UT with GMOS, mounted on Gemini-South. Using the SNID code (Blondin & Tonry, 2007, ApJ, 666, 1024) we find a good match with a Type II supernova at z=0.014, consistent with the redshift of its host galaxy 2MASX J17401447-5825586.

49 CFR 178.910 - Marking of Large Packagings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... stamped or embossed, the capital letters “UN” may be applied instead of the symbol; (ii) The code number...) The country authorizing the allocation of the mark. The letters “USA” indicate that the Large...

49 CFR 178.910 - Marking of Large Packagings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... stamped or embossed, the capital letters “UN” may be applied instead of the symbol; (ii) The code number...) The country authorizing the allocation of the mark. The letters “USA” indicate that the Large...

48 CFR 4.803 - Contents of contract files.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the type and extent of market research conducted. (7) Government estimate of contract price. (8) A... documentation— (i) Of the type and extent of market research; and (ii) That the NAICS code assigned to the...

Circadian Rhythm in the Expression of the mRNA Coding for the Apoprotein of the Light-Harvesting Complex of Photosystem II 1

PubMed Central

Tavladoraki, Paraskevi; Kloppstech, Klaus; Argyroudi-Akoyunoglou, Joan

1989-01-01

The mRNA coding for light-harvesting complex of PSII (LHC-II) apoprotein is present in etiolated bean (Phaseolus vulgaris L.) leaves; its level is low in 5-day-old leaves, increases about 3 to 4 times in 9- to 13-day-old leaves, and decreases thereafter. A red light pulse induces an increase in LHC-II mRNA level, which is reversed by far red light, in all ages of the etiolated tissue tested. The phytochrome-controlled initial increase of LHC-II mRNA level is higher in 9- and 13-day-old than in 5- and 17-day-old bean leaves. The amount of LHC-II mRNA, accumulated in the dark after a red light pulse, oscillates rhythmically with a period of about 24 hours. This rhythm is also observed in continuous white light and in the dark following exposure to continuous white light, and persists for at least 70 hours. A second red light pulse, applied 36 hours after initiation of the rhythm, induces a phase-shift, which is prevented by far red light immediately following the second red light pulse. A persistent, but gradually reduced, far red reversibility of the red light-induced increase in LHC-II mRNA level is observed. In contrast, far red reversibility of the red light-induced clock setting is only observed when far red follows immediately the red light. It is concluded that (a) the light-induced LHC-II mRNA accumulation follows an endogenous, circadian rhythm, for the appearance of which a red light pulse is sufficient, (b) the circadian oscillator is under phytochrome control, and (c) a stable Pfr form, which exists for several hours, is responsible for sustaining LHC-II gene transcription. Images Figure 1 Figure 2 Figure 8 PMID:16666825

Emission-line diagnostics of nearby H II regions including interacting binary populations

NASA Astrophysics Data System (ADS)

Xiao, Lin; Stanway, Elizabeth R.; Eldridge, J. J.

2018-06-01

We present numerical models of the nebular emission from H II regions around young stellar populations over a range of compositions and ages. The synthetic stellar populations include both single stars and interacting binary stars. We compare these models to the observed emission lines of 254 H II regions of 13 nearby spiral galaxies and 21 dwarf galaxies drawn from archival data. The models are created using the combination of the BPASS (Binary Population and Spectral Synthesis) code with the photoionization code CLOUDY to study the differences caused by the inclusion of interacting binary stars in the stellar population. We obtain agreement with the observed emission line ratios from the nearby star-forming regions and discuss the effect of binary-star evolution pathways on the nebular ionization of H II regions. We find that at population ages above 10 Myr, single-star models rapidly decrease in flux and ionization strength, while binary-star models still produce strong flux and high [O III]/H β ratios. Our models can reproduce the metallicity of H II regions from spiral galaxies, but we find higher metallicities than previously estimated for the H II regions from dwarf galaxies. Comparing the equivalent width of H β emission between models and observations, we find that accounting for ionizing photon leakage can affect age estimates for H II regions. When it is included, the typical age derived for H II regions is 5 Myr from single-star models, and up to 10 Myr with binary-star models. This is due to the existence of binary-star evolution pathways, which produce more hot Wolf-Rayet and helium stars at older ages. For future reference, we calculate new BPASS binary maximal starburst lines as a function of metallicity, and for the total model population, and present these in Appendix A.

Structure-related statistical singularities along protein sequences: a correlation study.

PubMed

Colafranceschi, Mauro; Colosimo, Alfredo; Zbilut, Joseph P; Uversky, Vladimir N; Giuliani, Alessandro

2005-01-01

A data set composed of 1141 proteins representative of all eukaryotic protein sequences in the Swiss-Prot Protein Knowledge base was coded by seven physicochemical properties of amino acid residues. The resulting numerical profiles were submitted to correlation analysis after the application of a linear (simple mean) and a nonlinear (Recurrence Quantification Analysis, RQA) filter. The main RQA variables, Recurrence and Determinism, were subsequently analyzed by Principal Component Analysis. The RQA descriptors showed that (i) within protein sequences is embedded specific information neither present in the codes nor in the amino acid composition and (ii) the most sensitive code for detecting ordered recurrent (deterministic) patterns of residues in protein sequences is the Miyazawa-Jernigan hydrophobicity scale. The most deterministic proteins in terms of autocorrelation properties of primary structures were found (i) to be involved in protein-protein and protein-DNA interactions and (ii) to display a significantly higher proportion of structural disorder with respect to the average data set. A study of the scaling behavior of the average determinism with the setting parameters of RQA (embedding dimension and radius) allows for the identification of patterns of minimal length (six residues) as possible markers of zones specifically prone to inter- and intramolecular interactions.

Main functions, recent updates, and applications of Synchrotron Radiation Workshop code

NASA Astrophysics Data System (ADS)

Chubar, Oleg; Rakitin, Maksim; Chen-Wiegart, Yu-Chen Karen; Chu, Yong S.; Fluerasu, Andrei; Hidas, Dean; Wiegart, Lutz

2017-08-01

The paper presents an overview of the main functions and new application examples of the "Synchrotron Radiation Workshop" (SRW) code. SRW supports high-accuracy calculations of different types of synchrotron radiation, and simulations of propagation of fully-coherent radiation wavefronts, partially-coherent radiation from a finite-emittance electron beam of a storage ring source, and time-/frequency-dependent radiation pulses of a free-electron laser, through X-ray optical elements of a beamline. An extended library of physical-optics "propagators" for different types of reflective, refractive and diffractive X-ray optics with its typical imperfections, implemented in SRW, enable simulation of practically any X-ray beamline in a modern light source facility. The high accuracy of calculation methods used in SRW allows for multiple applications of this code, not only in the area of development of instruments and beamlines for new light source facilities, but also in areas such as electron beam diagnostics, commissioning and performance benchmarking of insertion devices and individual X-ray optical elements of beamlines. Applications of SRW in these areas, facilitating development and advanced commissioning of beamlines at the National Synchrotron Light Source II (NSLS-II), are described.

An Orbit And Dispersion Correction Scheme for the PEP II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Donald, M.; Shoaee, H.

2011-09-01

To achieve optimum luminosity in a storage ring it is vital to control the residual vertical dispersion. In the original PEP storage ring, a scheme to control the residual dispersion function was implemented using the ring orbit as the controlling element. The 'best' orbit not necessarily giving the lowest vertical dispersion. A similar scheme has been implemented in both the on-line control code and in the simulation code LEGO. The method involves finding the response matrices (sensitivity of orbit/dispersion at each Beam-Position-Monitor (BPM) to each orbit corrector) and solving in a least squares sense for minimum orbit, dispersion function ormore » both. The optimum solution is usually a subset of the full least squares solution. A scheme of simultaneously correcting the orbits and dispersion has been implemented in the simulation code and on-line control system for PEP-II. The scheme is based on the eigenvector decomposition method. An important ingredient of the scheme is to choose the optimum eigenvectors that minimize the orbit, dispersion and corrector strength. Simulations indicate this to be a very effective way to control the vertical residual dispersion.« less

Visual Dysfunction Following Blast-Related Traumatic Brain Injury from the Battlefield

DTIC Science & Technology

2010-10-27

sequelae follow- ing a TBI [12, 13]. The occurrence of TBI-related ocular and visual disorders is varied, depending on the diagnostic criteria...measure, ocular/visual disor- der, was indicated by the ICD-9-CM diagnostic codes for ‘disorders of the eye and adnexa’ (360.0– 379.9) obtained from...II. Number and percentage of US service members in each ocular/visual disorder diagnostic category by TBI status. ICD-9-CM code and categorya TBI (n

Technology Evaluation for Treatment/Disposal of TNT Red Water

DTIC Science & Technology

1990-04-01

U.S. Army Toxic and Hazardous Materials Agency Aberdeen Proving Ground , MD 21010-5423 __ E=4N DISTRIBUTION UNLIMITED I I TECHNOLOGY EVALUATION FOR...ABERDEEN PROVING GROUND , MARYLAND 21010-5423 April 1990 I I SECURITY CLASSIFICATION OF T-HI5 PA iiREPORT DOCUMENTATION PAGE W 7"f 4 I. REPORT SECURITY...and ZIP Code) 7b, ADDRESS (City, State, and ZIP Code) ATTN: CETHA-TE-D Aberdeen Proving Ground , MD 21010-5401 BaG. NAME OF FUNDING /SPONSORING 8b

Range Sidelobe Response from the Use of Polyphase Signals in Spotlight Synthetic Aperture Radar

DTIC Science & Technology

2015-12-01

come to closure. I also want to thank my mother for raising me and instilling in me the work ethic and values that have propelled me through life. I...to describe the poly-phase signals at baseband. IQ notation is preferred for complex waveforms because it allows for an easy mathematical...variables. 15 Once the Frank-coded phase vector is created, the IQ signal generation discussed in Chapter II was used to generate a Frank-code phase

Self-adaptive multimethod optimization applied to a tailored heating forging process

NASA Astrophysics Data System (ADS)

Baldan, M.; Steinberg, T.; Baake, E.

2018-05-01

The presented paper describes an innovative self-adaptive multi-objective optimization code. Investigation goals concern proving the superiority of this code compared to NGSA-II and applying it to an inductor’s design case study addressed to a “tailored” heating forging application. The choice of the frequency and the heating time are followed by the determination of the turns number and their positions. Finally, a straightforward optimization is performed in order to minimize energy consumption using “optimal control”.

RNAP-II transcribes two small RNAs at the promoter and terminator regions of the RNAP-I gene in Saccharomyces cerevisiae.

PubMed

Mayán, Maria D

2013-01-01

Three RNA polymerases coexist in the ribosomal DNA of Saccharomyces cerevisiae. RNAP-I transcribes the 35S rRNA, RNAP-III transcribes the 5S rRNA and RNAP-II is found in both intergenic non-coding regions. Previously, we demonstrated that RNAP-II molecules bound to the intergenic non-coding regions (IGS) of the ribosomal locus are mainly found in a stalled conformation, and the stalled polymerase mediates chromatin interactions, which isolate RNAP-I from the RNAP-III transcriptional domain. Besides, RNAP-II transcribes both IGS regions at low levels, using different cryptic promoters. This report demonstrates that RNAP-II also transcribes two sequences located in the 5'- and 3'-ends of the 35S rRNA gene that overlap with the sequences of the 35S rRNA precursor transcribed by RNAP-I. The sequence located at the promoter region of RNAP-I, called the p-RNA transcript, binds to the transcription termination-related protein, Reb1p, while the T-RNA sequence, located in the termination sites of RNAP-I gene, contains the stem-loop recognized by Rtn1p, which is necessary for proper termination of RNAP-I. Because of their location, these small RNAs may play a key role in the initiation and termination of RNAP-I transcription. To correctly synthesize proteins, eukaryotic cells may retain a mechanism that connects the three main polymerases. This report suggests that cryptic transcription by RNAP-II may be required for normal transcription by RNAP-I in the ribosomal locus of S. cerevisiae. Copyright © 2012 John Wiley & Sons, Ltd.

7 CFR 251.5 - Eligibility determinations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF... the following criteria: (1) Agencies distributing to households. Organizations distributing... under the Internal Revenue Code (IRC), or (ii) Possess documentation from the Internal Revenue Service...

7 CFR 251.5 - Eligibility determinations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF... the following criteria: (1) Agencies distributing to households. Organizations distributing... under the Internal Revenue Code (IRC), or (ii) Possess documentation from the Internal Revenue Service...

40 CFR 158.32 - Format of data submissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... identification of the substance(s) tested and the test name or data requirement addressed. (ii) The author(s) of..., the name and address of the laboratory, project numbers or other identifying codes. (v) If the study...

Internet calculations of thermodynamic properties of substances: Some problems and results

NASA Astrophysics Data System (ADS)

Ustyuzhanin, E. E.; Ochkov, V. F.; Shishakov, V. V.; Rykov, S. V.

2016-11-01

Internet resources (databases, web sites and others) on thermodynamic properties R = (p,T,s,...) of technologically important substances are analyzed. These databases put online by a number of organizations (the Joint Institute for High Temperatures of the Russian Academy of Sciences, Standartinform, the National Institute of Standards and Technology USA, the Institute for Thermal Physics of the Siberian Branch of the Russian Academy of Sciences, etc) are investigated. Software codes are elaborated in the work in forms of “client functions” those have such characteristics: (i) they are placed on a remote server, (ii) they serve as open interactive Internet resources. A client can use them for a calculation of R properties of substances. “Complex client functions” are considered. They are focused on sharing (i) software codes elaborated to design of power plants (PP) and (ii) client functions those can calculate R properties of working fluids for PP.

The tubulin code at a glance.

PubMed

Gadadhar, Sudarshan; Bodakuntla, Satish; Natarajan, Kathiresan; Janke, Carsten

2017-04-15

Microtubules are key cytoskeletal elements of all eukaryotic cells and are assembled of evolutionarily conserved α-tubulin-β-tubulin heterodimers. Despite their uniform structure, microtubules fulfill a large diversity of functions. A regulatory mechanism to control the specialization of the microtubule cytoskeleton is the 'tubulin code', which is generated by (i) expression of different α- and β-tubulin isotypes, and by (ii) post-translational modifications of tubulin. In this Cell Science at a Glance article and the accompanying poster, we provide a comprehensive overview of the molecular components of the tubulin code, and discuss the mechanisms by which these components contribute to the generation of functionally specialized microtubules. © 2017. Published by The Company of Biologists Ltd.

A Tool for Longitudinal Beam Dynamics in Synchrotrons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ostiguy, J.-F.; Lebedev, V. A.

2017-05-01

A number of codes are available to simulate longitudinal dynamics in synchrotrons. Some established ones include TIBETAN, LONG1D, ESME and ORBIT. While they embody a wealth of accumulated wisdom and experience, most of these codes were written decades ago and to some extent they reflect the constraints of their time. As a result, there is an interest for updated tools taking better advantage of modern software and hardware capabilities. At Fermilab, the PIP-II project has provided the impetus for development of such a tool. In this contribution, we discuss design decisions and code architecture. A selection of test cases basedmore » on an initial prototype are also presented.« less

A Viscoelastic-Plastic Constitutive Model with a Finite Element Solution Methodology

DTIC Science & Technology

1978-06-01

where - r3 K f BT D B dv (4-15) • ,re E,,rae v ’,vp ,vp w F BT dv (4-17)A -vp -Vp 84 ii T In the above, K is the global viscoelastic stiffness matrix anl ...Code C4AA Port Hueneme. CA NAVSE ASYSCOM Code OOC (LT R. MacDougisl). Washington DC NAVSEC Code 6034 1 Library). Washington DC NAVSEC61RLACT PWO. Torni...ESEARCH CO LA HABRA, CA iBROOKSi 0ONCRFE It Il FCH-NoIOGY CORP. TACOMA. ’A At( ANL )ESONi ((tNRAI) ASSOC. Van NuNs CA iA. Luisonit I)RA Vt COR(P I’muitt

CLUMPY: A code for γ-ray signals from dark matter structures

NASA Astrophysics Data System (ADS)

Charbonnier, Aldée; Combet, Céline; Maurin, David

2012-03-01

We present the first public code for semi-analytical calculation of the γ-ray flux astrophysical J-factor from dark matter annihilation/decay in the Galaxy, including dark matter substructures. The core of the code is the calculation of the line of sight integral of the dark matter density squared (for annihilations) or density (for decaying dark matter). The code can be used in three modes: i) to draw skymaps from the Galactic smooth component and/or the substructure contributions, ii) to calculate the flux from a specific halo (that is not the Galactic halo, e.g. dwarf spheroidal galaxies) or iii) to perform simple statistical operations from a list of allowed DM profiles for a given object. Extragalactic contributions and other tracers of DM annihilation (e.g. positrons, anti-protons) will be included in a second release.

Comparative validity of MMPI-2 and MCMI-II personality disorder classifications.

PubMed

Wise, E A

1996-06-01

Minnesota Multiphasic Personality Inventory-2 (MMPI-2) overlapping and nonoverlapping scales were demonstrated to perform comparably to their original MMPI forms. They were then evaluated for convergent and discriminant validity with the Million Clinical Multiaxial Inventory-II (MCMI-II) personality disorder scales. The MMPI-2 and MCMI-II personality disorder scales demonstrated convergent and discriminant coefficients similar to their original forms. However, the MMPI-2 personality scales classified significantly more of the sample as Dramatic, whereas the MCMI-II diagnosed more of the sample as Anxious. Furthermore, single-scale and 2-point code type classification rates were quite low, indicating that at the level of the individual, the personality disorder scales are not measuring comparable constructs. Hence, each instrument is providing similar and unique information, justifying their continued use together for the purpose of diagnosing personality disorders.

Digital optical computer II

NASA Astrophysics Data System (ADS)

Guilfoyle, Peter S.; Stone, Richard V.

1991-12-01

OptiComp is currently completing a 32-bit, fully programmable digital optical computer (DOC II) that is designed to operate in a UNIX environment running RISC microcode. OptiComp's DOC II architecture is focused toward parallel microcode implementation where data is input in a dual rail format. By exploiting the physical principals inherent to optics (speed and low power consumption), an architectural balance of optical interconnects and software code efficiency can be achieved including high fan-in and fan-out. OptiComp's DOC II program is jointly sponsored by the Office of Naval Research (ONR), the Strategic Defense Initiative Office (SDIO), NASA space station group and Rome Laboratory (USAF). This paper not only describes the motivational basis behind DOC II but also provides an optical overview and architectural summary of the device that allows the emulation of any digital instruction set.

ATLAS Test Program Generator II (AGEN II). Volume I. Executive Software System.

DTIC Science & Technology

1980-08-01

features. l-1 C. To provide detailed descriptions of each of the system components and modules and their corresponding flowcharts. D. To describe methods of...contains the FORTRAN source code listings to enable programmer to do the expansions and modifications. The methods and details of adding another...characteristics of the network. The top-down implementa- tion method is therefore suggested. This method starts at the top by designing the IVT modules in

Nebular Continuum and Line Emission in Stellar Population Synthesis Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Byler, Nell; Dalcanton, Julianne J.; Conroy, Charlie

Accounting for nebular emission when modeling galaxy spectral energy distributions (SEDs) is important, as both line and continuum emissions can contribute significantly to the total observed flux. In this work, we present a new nebular emission model integrated within the Flexible Stellar Population Synthesis code that computes the line and continuum emission for complex stellar populations using the photoionization code Cloudy. The self-consistent coupling of the nebular emission to the matched ionizing spectrum produces emission line intensities that correctly scale with the stellar population as a function of age and metallicity. This more complete model of galaxy SEDs will improvemore » estimates of global gas properties derived with diagnostic diagrams, star formation rates based on H α , and physical properties derived from broadband photometry. Our models agree well with results from other photoionization models and are able to reproduce observed emission from H ii regions and star-forming galaxies. Our models show improved agreement with the observed H ii regions in the Ne iii/O ii plane and show satisfactory agreement with He ii emission from z = 2 galaxies, when including rotating stellar models. Models including post-asymptotic giant branch stars are able to reproduce line ratios consistent with low-ionization emission regions. The models are integrated into current versions of FSPS and include self-consistent nebular emission predictions for MIST and Padova+Geneva evolutionary tracks.« less

Definition of RNA polymerase II CoTC terminator elements in the human genome.

PubMed

Nojima, Takayuki; Dienstbier, Martin; Murphy, Shona; Proudfoot, Nicholas J; Dye, Michael J

2013-04-25

Mammalian RNA polymerase II (Pol II) transcription termination is an essential step in protein-coding gene expression that is mediated by pre-mRNA processing activities and DNA-encoded terminator elements. Although much is known about the role of pre-mRNA processing in termination, our understanding of the characteristics and generality of terminator elements is limited. Whereas promoter databases list up to 40,000 known and potential Pol II promoter sequences, fewer than ten Pol II terminator sequences have been described. Using our knowledge of the human β-globin terminator mechanism, we have developed a selection strategy for mapping mammalian Pol II terminator elements. We report the identification of 78 cotranscriptional cleavage (CoTC)-type terminator elements at endogenous gene loci. The results of this analysis pave the way for the full understanding of Pol II termination pathways and their roles in gene expression. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

Initial Aerodynamic and Acoustic Study of an Active Twist Rotor Using a Loosely Coupled CFD/CSD Method

NASA Technical Reports Server (NTRS)

Boyd, David D. Jr.

2009-01-01

Preliminary aerodynamic and performance predictions for an active twist rotor for a HART-II type of configuration are performed using a computational fluid dynamics (CFD) code, OVERFLOW2, and a computational structural dynamics (CSD) code, CAMRAD -II. These codes are loosely coupled to compute a consistent set of aerodynamics and elastic blade motions. Resultant aerodynamic and blade motion data are then used in the Ffowcs-Williams Hawkins solver, PSU-WOPWOP, to compute noise on an observer plane under the rotor. Active twist of the rotor blade is achieved in CAMRAD-II by application of a periodic torsional moment couple (of equal and opposite sign) at the blade root and tip at a specified frequency and amplitude. To provide confidence in these particular active twist predictions for which no measured data is available, the rotor system geometry and computational set up examined here are identical to that used in a previous successful Higher Harmonic Control (HHC) computational study. For a single frequency equal to three times the blade passage frequency (3P), active twist is applied across a range of control phase angles at two different amplitudes. Predicted results indicate that there are control phase angles where the maximum mid-frequency noise level and the 4P non -rotating hub vibrations can be reduced, potentially, both at the same time. However, these calculated reductions are predicted to come with a performance penalty in the form of a reduction in rotor lift-to-drag ratio due to an increase in rotor profile power.

Numerical simulation of fiber and wire array Z-pinches with Trac-II

NASA Astrophysics Data System (ADS)

Reisman, David Barton

Trac-II is a two dimensional axisymmetric resistive MHD code. It simulates all three spatial components (r, z, φ) of the magnetic field and fluid velocity vectors, and the plasma is treated as a single fluid with two temperatures (Te,Ti). In addition, it can optionally include a self-consistent external circuit. Recent modifications to the code include the addition of the 3-T radiation model, a 4-phase (solid- liquid-vapor-plasma) equation of state model (QEOS), a 4- phase electrical/thermal conductivity model, and an implicit solution of poloidal (Bz,Br) magnetic field diffusion. These changes permit a detailed study of fiber and wire array Z-pinches. Specifically, Trac-II is used to study the wire array Z-pinch at the PBFA-Z pulse power generator at Sandia National Laboratory. First, in 1-D we examine the behavior of a single wire in the Z-pinch. Then, using these results as initial radial conditions in 2-D, we investigate the dynamics of wire array configurations in the r-z and r-θ plane. In the r- z plane we examine the growth of the m = 0 or ``sausage'' instability in single wires within the array. In the r-θ plane we examine the merging behavior between neighboring wires. Special emphasis is placed on trying to explain how instability growth affects the performance of the Z-pinch. Lastly, we introduce Trac-III, a 3-D MHD code, and illustrate the m = 1 or ``kink'' instability. We also discuss how Trac-III can be modified to simulate the wire array Z-pinch.

Synthetic observations of wave propagation in a sunspot umbra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Felipe, T.; Socas-Navarro, H.; Khomenko, E.

2014-11-01

Spectropolarimetric temporal series from Fe I λ6301.5 Å and Ca II infrared triplet lines are obtained by applying the Stokes synthesis code NICOLE to a numerical simulation of wave propagation in a sunspot umbra from MANCHA code. The analysis of the phase difference between Doppler velocity and intensity core oscillations of the Fe I λ6301.5 Å line reveals that variations in the intensity are produced by opacity fluctuations rather than intrinsic temperature oscillations, except for frequencies between 5 and 6.5 mHz. On the other hand, the photospheric magnetic field retrieved from the weak field approximation provides the intrinsic magnetic fieldmore » oscillations associated to wave propagation. Our results suggest that this is due to the low magnetic field gradient of our sunspot model. The Stokes parameters of the chromospheric Ca II infrared triplet lines show striking variations as shock waves travel through the formation height of the lines, including emission self-reversals in the line core and highly abnormal Stokes V profiles. Magnetic field oscillations inferred from the Ca II infrared lines using the weak field approximation appear to be related with the magnetic field strength variation between the photosphere and the chromosphere.« less

Cryptanalysis in World War II--and Mathematics Education.

ERIC Educational Resources Information Center

Hilton, Peter

1984-01-01

Hilton describes the team of cryptanalysts who tried to decipher German and Japanese codes during the Second World War. The work of Turing, essentially developing the computer, is reported, as well as inferences about pure and applied mathematics. (MNS)

49 CFR 178.502 - Identification codes for packagings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... construction, as follows: (i) “A” means steel (all types and surface treatments). (ii) “B” means aluminum. (iii) “C” means natural wood. (iv) “D” means plywood. (v) “F” means reconstituted wood. (vi) “G” means...

Engineering properties of brittle repair materials : final report : volume II.

DOT National Transportation Integrated Search

1992-09-01

Most codes of practice prescribe procedures for selecting patch configuration and materials based on tests devised for evaluating new pavement materials. This study is aimed at examining the special consideration to be given to such evaluation proced...

Health information management: an introduction to disease classification and coding.

PubMed

Mony, Prem Kumar; Nagaraj, C

2007-01-01

Morbidity and mortality data constitute an important component of a health information system and their coding enables uniform data collation and analysis as well as meaningful comparisons between regions or countries. Strengthening the recording and reporting systems for health monitoring is a basic requirement for an efficient health information management system. Increased advocacy for and awareness of a uniform coding system together with adequate capacity building of physicians, coders and other allied health and information technology personnel would pave the way for a valid and reliable health information management system in India. The core requirements for the implementation of disease coding are: (i) support from national/institutional health administrators, (ii) widespread availability of the ICD-10 material for morbidity and mortality coding; (iii) enhanced human and financial resources; and (iv) optimal use of informatics. We describe the methodology of a disease classification and codification system as also its applications for developing and maintaining an effective health information management system for India.

Emergence of an abstract categorical code enabling the discrimination of temporally structured tactile stimuli

PubMed Central

Rossi-Pool, Román; Salinas, Emilio; Zainos, Antonio; Alvarez, Manuel; Vergara, José; Parga, Néstor; Romo, Ranulfo

2016-01-01

The problem of neural coding in perceptual decision making revolves around two fundamental questions: (i) How are the neural representations of sensory stimuli related to perception, and (ii) what attributes of these neural responses are relevant for downstream networks, and how do they influence decision making? We studied these two questions by recording neurons in primary somatosensory (S1) and dorsal premotor (DPC) cortex while trained monkeys reported whether the temporal pattern structure of two sequential vibrotactile stimuli (of equal mean frequency) was the same or different. We found that S1 neurons coded the temporal patterns in a literal way and only during the stimulation periods and did not reflect the monkeys’ decisions. In contrast, DPC neurons coded the stimulus patterns as broader categories and signaled them during the working memory, comparison, and decision periods. These results show that the initial sensory representation is transformed into an intermediate, more abstract categorical code that combines past and present information to ultimately generate a perceptually informed choice. PMID:27872293

PHASE I MATERIALS PROPERTY DATABASE DEVELOPMENT FOR ASME CODES AND STANDARDS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ren, Weiju; Lin, Lianshan

2013-01-01

To support the ASME Boiler and Pressure Vessel Codes and Standard (BPVC) in modern information era, development of a web-based materials property database is initiated under the supervision of ASME Committee on Materials. To achieve efficiency, the project heavily draws upon experience from development of the Gen IV Materials Handbook and the Nuclear System Materials Handbook. The effort is divided into two phases. Phase I is planned to deliver a materials data file warehouse that offers a depository for various files containing raw data and background information, and Phase II will provide a relational digital database that provides advanced featuresmore » facilitating digital data processing and management. Population of the database will start with materials property data for nuclear applications and expand to data covering the entire ASME Code and Standards including the piping codes as the database structure is continuously optimized. The ultimate goal of the effort is to establish a sound cyber infrastructure that support ASME Codes and Standards development and maintenance.« less

Deep Impact Delta II Launch Vehicle Cracked Thick Film Coating on Electronic Packages Technical Consultation Report

NASA Technical Reports Server (NTRS)

Cameron, Kenneth D.; Kichak, Robert A.; Piascik, Robert S.; Leidecker, Henning W.; Wilson, Timmy R.

2009-01-01

The Deep Impact spacecraft was launched on a Boeing Delta II rocket from Cape Canaveral Air Force Station (CCAFS) on January 12, 2005. Prior to the launch, the Director of the Office of Safety and Mission Assurance (OS&MA) requested the NASA Engineering and Safety Center (NESC) lead a team to render an independent opinion on the rationale for flight and the risk code assignments for the hazard of cracked Thick Film Assemblies (TFAs) in the E-packages of the Delta II launch vehicle for the Deep Impact Mission. The results of the evaluation are contained in this report.

Exploring a QoS Driven Scheduling Approach for Peer-to-Peer Live Streaming Systems with Network Coding

PubMed Central

Cui, Laizhong; Lu, Nan; Chen, Fu

2014-01-01

Most large-scale peer-to-peer (P2P) live streaming systems use mesh to organize peers and leverage pull scheduling to transmit packets for providing robustness in dynamic environment. The pull scheduling brings large packet delay. Network coding makes the push scheduling feasible in mesh P2P live streaming and improves the efficiency. However, it may also introduce some extra delays and coding computational overhead. To improve the packet delay, streaming quality, and coding overhead, in this paper are as follows. we propose a QoS driven push scheduling approach. The main contributions of this paper are: (i) We introduce a new network coding method to increase the content diversity and reduce the complexity of scheduling; (ii) we formulate the push scheduling as an optimization problem and transform it to a min-cost flow problem for solving it in polynomial time; (iii) we propose a push scheduling algorithm to reduce the coding overhead and do extensive experiments to validate the effectiveness of our approach. Compared with previous approaches, the simulation results demonstrate that packet delay, continuity index, and coding ratio of our system can be significantly improved, especially in dynamic environments. PMID:25114968

An Efficient Method for Verifying Gyrokinetic Microstability Codes

NASA Astrophysics Data System (ADS)

Bravenec, R.; Candy, J.; Dorland, W.; Holland, C.

2009-11-01

Benchmarks for gyrokinetic microstability codes can be developed through successful ``apples-to-apples'' comparisons among them. Unlike previous efforts, we perform the comparisons for actual discharges, rendering the verification efforts relevant to existing experiments and future devices (ITER). The process requires i) assembling the experimental analyses at multiple times, radii, discharges, and devices, ii) creating the input files ensuring that the input parameters are faithfully translated code-to-code, iii) running the codes, and iv) comparing the results, all in an organized fashion. The purpose of this work is to automate this process as much as possible: At present, a python routine is used to generate and organize GYRO input files from TRANSP or ONETWO analyses. Another routine translates the GYRO input files into GS2 input files. (Translation software for other codes has not yet been written.) Other python codes submit the multiple GYRO and GS2 jobs, organize the results, and collect them into a table suitable for plotting. (These separate python routines could easily be consolidated.) An example of the process -- a linear comparison between GYRO and GS2 for a DIII-D discharge at multiple radii -- will be presented.

Validation of a vector version of the 6S radiative transfer code for atmospheric correction of satellite data. Part II. Homogeneous Lambertian and anisotropic surfaces.

PubMed

Kotchenova, Svetlana Y; Vermote, Eric F

2007-07-10

This is the second part of the validation effort of the recently developed vector version of the 6S (Second Simulation of a Satellite Signal in the Solar Spectrum) radiative transfer code (6SV1), primarily used for the calculation of look-up tables in the Moderate Resolution Imaging Spectroradiometer (MODIS) atmospheric correction algorithm. The 6SV1 code was tested against a Monte Carlo code and Coulson's tabulated values for molecular and aerosol atmospheres bounded by different Lambertian and anisotropic surfaces. The code was also tested in scalar mode against the scalar code SHARM to resolve the previous 6S accuracy issues in the case of an anisotropic surface. All test cases were characterized by good agreement between the 6SV1 and the other codes: The overall relative error did not exceed 0.8%. The study also showed that ignoring the effects of radiation polarization in the atmosphere led to large errors in the simulated top-of-atmosphere reflectances: The maximum observed error was approximately 7.2% for both Lambertian and anisotropic surfaces.

Validation of a vector version of the 6S radiative transfer code for atmospheric correction of satellite data. Part II. Homogeneous Lambertian and anisotropic surfaces

NASA Astrophysics Data System (ADS)

Kotchenova, Svetlana Y.; Vermote, Eric F.

2007-07-01

This is the second part of the validation effort of the recently developed vector version of the 6S (Second Simulation of a Satellite Signal in the Solar Spectrum) radiative transfer code (6SV1), primarily used for the calculation of look-up tables in the Moderate Resolution Imaging Spectroradiometer (MODIS) atmospheric correction algorithm. The 6SV1 code was tested against a Monte Carlo code and Coulson's tabulated values for molecular and aerosol atmospheres bounded by different Lambertian and anisotropic surfaces. The code was also tested in scalar mode against the scalar code SHARM to resolve the previous 6S accuracy issues in the case of an anisotropic surface. All test cases were characterized by good agreement between the 6SV1 and the other codes: The overall relative error did not exceed 0.8%. The study also showed that ignoring the effects of radiation polarization in the atmosphere led to large errors in the simulated top-of-atmosphere reflectances: The maximum observed error was approximately 7.2% for both Lambertian and anisotropic surfaces.

Isolation and characterisation of mRNA encoding the salmon- and chicken-II type gonadotrophin-releasing hormones in the teleost fish Rutilus rutilus (Cyprinidae).

PubMed

Penlington, M C; Williams, M A; Sumpter, J P; Rand-Weaver, M; Hoole, D; Arme, C

1997-12-01

The complementary DNAs (cDNA) encoding the [Trp7,Leu8]-gonadotrophin-releasing hormone (salmon-type GnRH; sGnRH:GeneBank accession no. u60667) and the [His5,Trp7,Tyr8]-GnRH (chicken-II-type GnRH; cGnRH-II: GeneBank accession no. u60668) precursor in the roach (Rutilus rutilus) were isolated and sequenced following reverse transcription and rapid amplification of cDNA ends (RACE). The sGnRH and cGnRH-II precursor cDNAs consisted of 439 and 628 bp, and included open reading frames of 282 and 255 bp respectively. The structures of the encoded peptides were the same as GnRHs previously identified in other vertebrates. The sGnRH and cGnRH-II precursor cDNAs, including the non-coding regions, had 88.6 and 79.9% identity respectively, to those identified in goldfish (Carassius auratus). However, significant similarity was not observed between the non-coding regions of the GnRH cDNAs of Cyprinidae and other fish. The presumed third exon, encoding partial sGnRH associated peptide (GAP) of roach, demonstrated significant nucleotide and amino acid similarity with the appropriate regions in the goldfish, but not with other species, and this may indicate functional differences of GAP between different families of fish. cGnRH-II precursor cDNAs from roach had relatively high nucleotide similarity across this GnRH variant. Cladistic analysis classified the sGnRH and cGnRH-II precursor cDNAs into three and two groups respectively. However, the divergence between nucleotide sequences within the sGnRH variant was greater than those encoding the cGnRH-II precursors. Consistent with the consensus developed from previous studies, Northern blot analysis demonstrated that expression of sGnRH and cGnRH-II was restricted to the olfactory bulbs and midbrain of roach respectively. This work forms the basis for further study on the mechanisms by which the tapeworm, Ligula intestinalis, interacts with the pituitary-gonadal axis of its fish host.

Bumper 3 Update for IADC Protection Manual

NASA Technical Reports Server (NTRS)

Christiansen, Eric L.; Nagy, Kornel; Hyde, Jim

2016-01-01

The Bumper code has been the standard in use by NASA and contractors to perform meteoroid/debris risk assessments since 1990. It has undergone extensive revisions and updates [NASA JSC HITF website; Christiansen et al., 1992, 1997]. NASA Johnson Space Center (JSC) has applied BUMPER to risk assessments for Space Station, Shuttle, Mir, Extravehicular Mobility Units (EMU) space suits, and other spacecraft (e.g., LDEF, Iridium, TDRS, and Hubble Space Telescope). Bumper continues to be updated with changes in the ballistic limit equations describing failure threshold of various spacecraft components, as well as changes in the meteoroid and debris environment models. Significant efforts are expended to validate Bumper and benchmark it to other meteoroid/debris risk assessment codes. Bumper 3 is a refactored version of Bumper II. The structure of the code was extensively modified to improve maintenance, performance and flexibility. The architecture was changed to separate the frequently updated ballistic limit equations from the relatively stable common core functions of the program. These updates allow NASA to produce specific editions of the Bumper 3 that are tailored for specific customer requirements. The core consists of common code necessary to process the Micrometeoroid and Orbital Debris (MMOD) environment models, assess shadowing and calculate MMOD risk. The library of target response subroutines includes a board range of different types of MMOD shield ballistic limit equations as well as equations describing damage to various spacecraft subsystems or hardware (thermal protection materials, windows, radiators, solar arrays, cables, etc.). The core and library of ballistic response subroutines are maintained under configuration control. A change in the core will affect all editions of the code, whereas a change in one or more of the response subroutines will affect all editions of the code that contain the particular response subroutines which are modified. Note that the Bumper II program is no longer maintained or distributed by NASA.

[The evolution of the Italian Code of Medical Deontology: a historical-epistemological perspective].

PubMed

Conti, A A

The Italian Code of Medical Deontology is a set of self-discipline rules prefixed by the medical profession, that are mandatory for the members of the medical registers, who must conform to these rules. The history of the Italian Code of Medical Deontology dates back to the beginning of the twentieth century. In 1903 it appeared in the form of a "Code of Ethics and Deontology" and was prepared by the Board of the Medical Register of Sassari (Sardinia). This Board inserted the principles inspiring the correct practice of the medical profession in an articulated and self-normative system, also foreseeing disciplinary measures. About ten years later, in 1912, the Medical Register of Turin (Piedmont) elaborated a Code which constituted the basis for a subsequent elaboration leading to a Unified Code of Medical Ethics (1924). After World War II the idea prevailed in Italy that the codes of medical deontology should undergo periodical review, updating and dissemination, and the new 1947 text (Turin) was for the first time amply diffused among Italian physicians. The next national code dates back to 1958, and twenty years later a revision was published. In the 1989 Code new topics appeared, including organ transplantation, artificial in vitro insemination and the role of police doctors; these and other issues were later developed in the 1995, 1998 and 2006 versions of the Code. The last available edition of the Italian Code of Medical Deontology is that of May 2014.

Efficient full wave code for the coupling of large multirow multijunction LH grills

NASA Astrophysics Data System (ADS)

Preinhaelter, Josef; Hillairet, Julien; Milanesio, Daniele; Maggiora, Riccardo; Urban, Jakub; Vahala, Linda; Vahala, George

2017-11-01

The full wave code OLGA, for determining the coupling of a single row lower hybrid launcher (waveguide grills) to the plasma, is extended to handle multirow multijunction active passive structures (like the C3 and C4 launchers on TORE SUPRA) by implementing the scattering matrix formalism. The extended code is still computationally fast because of the use of (i) 2D splines of the plasma surface admittance in the accessibility region of the k-space, (ii) high order Gaussian quadrature rules for the integration of the coupling elements and (iii) utilizing the symmetries of the coupling elements in the multiperiodic structures. The extended OLGA code is benchmarked against the ALOHA-1D, ALOHA-2D and TOPLHA codes for the coupling of the C3 and C4 TORE SUPRA launchers for several plasma configurations derived from reflectometry and interferometery. Unlike nearly all codes (except the ALOHA-1D code), OLGA does not require large computational resources and can be used for everyday usage in planning experimental runs. In particular, it is shown that the OLGA code correctly handles the coupling of the C3 and C4 launchers over a very wide range of plasma densities in front of the grill.

The impact of three discharge coding methods on the accuracy of diagnostic coding and hospital reimbursement for inpatient medical care.

PubMed

Tsopra, Rosy; Peckham, Daniel; Beirne, Paul; Rodger, Kirsty; Callister, Matthew; White, Helen; Jais, Jean-Philippe; Ghosh, Dipansu; Whitaker, Paul; Clifton, Ian J; Wyatt, Jeremy C

2018-07-01

Coding of diagnoses is important for patient care, hospital management and research. However coding accuracy is often poor and may reflect methods of coding. This study investigates the impact of three alternative coding methods on the inaccuracy of diagnosis codes and hospital reimbursement. Comparisons of coding inaccuracy were made between a list of coded diagnoses obtained by a coder using (i)the discharge summary alone, (ii)case notes and discharge summary, and (iii)discharge summary with the addition of medical input. For each method, inaccuracy was determined for the primary, secondary diagnoses, Healthcare Resource Group (HRG) and estimated hospital reimbursement. These data were then compared with a gold standard derived by a consultant and coder. 107 consecutive patient discharges were analysed. Inaccuracy of diagnosis codes was highest when a coder used the discharge summary alone, and decreased significantly when the coder used the case notes (70% vs 58% respectively, p < 0.0001) or coded from the discharge summary with medical support (70% vs 60% respectively, p < 0.0001). When compared with the gold standard, the percentage of incorrect HRGs was 42% for discharge summary alone, 31% for coding with case notes, and 35% for coding with medical support. The three coding methods resulted in an annual estimated loss of hospital remuneration of between £1.8 M and £16.5 M. The accuracy of diagnosis codes and percentage of correct HRGs improved when coders used either case notes or medical support in addition to the discharge summary. Further emphasis needs to be placed on improving the standard of information recorded in discharge summaries. Copyright © 2018 Elsevier B.V. All rights reserved.

Mechanical Design and Analysis of LCLS II 2 K Cold Box

NASA Astrophysics Data System (ADS)

Yang, S.; Dixon, K.; Laverdure, N.; Rath, D.; Bevins, M.; Bai, H.; Kaminski, S.; Ravindranath, V.

2017-12-01

The mechanical design and analysis of the LCLS II 2 K cold box are presented. Its feature and functionality are discussed. ASME B31.3 was used to design its internal piping, and compliance of the piping code was ensured through flexibility analysis. The 2 K cold box was analyzed using ANSYS 17.2; the requirements of the applicable codes—ASME Section VIII Division 2 and ASCE 7-10—were satisfied. Seismic load was explicitly considered in both analyses.

Improving Seismic Event Characterisation

DTIC Science & Technology

1996-07-22

classificat i,; and further phase identification . 6.4.3 Seismic event interpretation The’ system of event processing is based on an assumption tree ...and is enhanced with usez by a network. 14, SUBJECT TERMSý 15. NUMBER OF PAGES seismic models, travel. timtes phase identification 16 PRICE CODE 17...hesimwinlia’ rati of t lieDl scisillograonis is 2/3 secondIs andI the receiver spaci mi is 1 /3 degreeus. ’lIi iiaiiiii iltdiwic’ ewe ii rayv-the~oret~icaIl

26 CFR 4.954-0 - Introduction.

Code of Federal Regulations, 2012 CFR

2012-04-01

.... (2) Special rules. (i) Adding substantial value. (ii) Substantiality of foreign organization. (iii... Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) TEMPORARY INCOME TAX REGULATIONS UNDER SECTION 954 OF THE INTERNAL REVENUE CODE § 4.954-0 Introduction. (a...

26 CFR 4.954-0 - Introduction.

Code of Federal Regulations, 2013 CFR

2013-04-01

.... (2) Special rules. (i) Adding substantial value. (ii) Substantiality of foreign organization. (iii... Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) TEMPORARY INCOME TAX REGULATIONS UNDER SECTION 954 OF THE INTERNAL REVENUE CODE § 4.954-0 Introduction. (a...

Addressing medical coding and billing part II: a strategy for achieving compliance. A risk management approach for reducing coding and billing errors.

PubMed Central

Adams, Diane L.; Norman, Helen; Burroughs, Valentine J.

2002-01-01

Medical practice today, more than ever before, places greater demands on physicians to see more patients, provide more complex medical services and adhere to stricter regulatory rules, leaving little time for coding and billing. Yet, the need to adequately document medical records, appropriately apply billing codes and accurately charge insurers for medical services is essential to the medical practice's financial condition. Many physicians rely on office staff and billing companies to process their medical bills without ever reviewing the bills before they are submitted for payment. Some physicians may not be receiving the payment they deserve when they do not sufficiently oversee the medical practice's coding and billing patterns. This article emphasizes the importance of monitoring and auditing medical record documentation and coding application as a strategy for achieving compliance and reducing billing errors. When medical bills are submitted with missing and incorrect information, they may result in unpaid claims and loss of revenue to physicians. Addressing Medical Audits, Part I--A Strategy for Achieving Compliance--CMS, JCAHO, NCQA, published January 2002 in the Journal of the National Medical Association, stressed the importance of preparing the medical practice for audits. The article highlighted steps the medical practice can take to prepare for audits and presented examples of guidelines used by regulatory agencies to conduct both medical and financial audits. The Medicare Integrity Program was cited as an example of guidelines used by regulators to identify coding errors during an audit and deny payment to providers when improper billing occurs. For each denied claim, payments owed to the medical practice are are also denied. Health care is, no doubt, a costly endeavor for health care providers, consumers and insurers. The potential risk to physicians for improper billing may include loss of revenue, fraud investigations, financial sanction, disciplinary action and exclusion from participation in government programs. Part II of this article recommends an approach for assessing potential risk, preventing improper billing, and improving financial management of the medical practice. Images p432-a PMID:12078924

A comparison of the COG and MCNP codes in computational neutron capture therapy modeling, Part II: gadolinium neutron capture therapy models and therapeutic effects.

PubMed

Wangerin, K; Culbertson, C N; Jevremovic, T

2005-08-01

The goal of this study was to evaluate the COG Monte Carlo radiation transport code, developed and tested by Lawrence Livermore National Laboratory, for gadolinium neutron capture therapy (GdNCT) related modeling. The validity of COG NCT model has been established for this model, and here the calculation was extended to analyze the effect of various gadolinium concentrations on dose distribution and cell-kill effect of the GdNCT modality and to determine the optimum therapeutic conditions for treating brain cancers. The computational results were compared with the widely used MCNP code. The differences between the COG and MCNP predictions were generally small and suggest that the COG code can be applied to similar research problems in NCT. Results for this study also showed that a concentration of 100 ppm gadolinium in the tumor was most beneficial when using an epithermal neutron beam.

Stalled RNAP-II molecules bound to non-coding rDNA spacers are required for normal nucleolus architecture.

PubMed

Freire-Picos, M A; Landeira-Ameijeiras, V; Mayán, María D

2013-07-01

The correct distribution of nuclear domains is critical for the maintenance of normal cellular processes such as transcription and replication, which are regulated depending on their location and surroundings. The most well-characterized nuclear domain, the nucleolus, is essential for cell survival and metabolism. Alterations in nucleolar structure affect nuclear dynamics; however, how the nucleolus and the rest of the nuclear domains are interconnected is largely unknown. In this report, we demonstrate that RNAP-II is vital for the maintenance of the typical crescent-shaped structure of the nucleolar rDNA repeats and rRNA transcription. When stalled RNAP-II molecules are not bound to the chromatin, the nucleolus loses its typical crescent-shaped structure. However, the RNAP-II interaction with Seh1p, or cryptic transcription by RNAP-II, is not critical for morphological changes. Copyright © 2013 John Wiley & Sons, Ltd.

Comparison of reversible methods for data compression

NASA Astrophysics Data System (ADS)

Heer, Volker K.; Reinfelder, Hans-Erich

1990-07-01

Widely differing methods for data compression described in the ACR-NEMA draft are used in medical imaging. In our contribution we will review various methods briefly and discuss the relevant advantages and disadvantages. In detail we evaluate 1st order DPCM pyramid transformation and S transformation. We compare as coding algorithms both fixed and adaptive Huffman coding and Lempel-Ziv coding. Our comparison is performed on typical medical images from CT MR DSA and DLR (Digital Luminescence Radiography). Apart from the achieved compression factors we take into account CPU time required and main memory requirement both for compression and for decompression. For a realistic comparison we have implemented the mentioned algorithms in the C program language on a MicroVAX II and a SPARC station 1. 2.

Mapping Department of Defense laboratory results to Logical Observation Identifiers Names and Codes (LOINC).

PubMed

Lau, Lee Min; Banning, Pam D; Monson, Kent; Knight, Elva; Wilson, Pat S; Shakib, Shaun C

2005-01-01

The Department of Defense (DoD) has used a common application, Composite Health Care System (CHCS), throughout all DoD facilities. However, the master files used to encode patient data in CHCS are not identical across DoD facilities. The encoded data is thus not interoperable from one DoD facility to another. To enable data interoperability in the next-generation system, CHCS II, and for the DoD to exchange laboratory results with external organizations such as the Veterans Administration (VA), the disparate master file codes for laboratory results are mapped to Logical Observation Identifier Names and Codes (LOINC) wherever possible. This paper presents some findings from our experience mapping DoD laboratory results to LOINC.

Local non-Calderbank-Shor-Steane quantum error-correcting code on a three-dimensional lattice

NASA Astrophysics Data System (ADS)

Kim, Isaac H.

2011-05-01

We present a family of non-Calderbank-Shor-Steane quantum error-correcting code consisting of geometrically local stabilizer generators on a 3D lattice. We study the Hamiltonian constructed from ferromagnetic interaction of overcomplete set of local stabilizer generators. The degenerate ground state of the system is characterized by a quantum error-correcting code whose number of encoded qubits are equal to the second Betti number of the manifold. These models (i) have solely local interactions; (ii) admit a strong-weak duality relation with an Ising model on a dual lattice; (iii) have topological order in the ground state, some of which survive at finite temperature; and (iv) behave as classical memory at finite temperature.

LEGO: A modular accelerator design code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Donald, M.; Irwin, J.

1997-08-01

An object-oriented accelerator design code has been designed and implemented in a simple and modular fashion. It contains all major features of its predecessors: TRACY and DESPOT. All physics of single-particle dynamics is implemented based on the Hamiltonian in the local frame of the component. Components can be moved arbitrarily in the three dimensional space. Several symplectic integrators are used to approximate the integration of the Hamiltonian. A differential algebra class is introduced to extract a Taylor map up to arbitrary order. Analysis of optics is done in the same way both for the linear and nonlinear case. Currently, themore » code is used to design and simulate the lattices of the PEP-II. It will also be used for the commissioning.« less

A User’s Manual for Electromagnetic Surface Patch (ESP) Code. Version II. Polygonal Plates and Wires.

DTIC Science & Technology

1983-09-01

to geometries not large in terms of wavelength and the lack of analytical results which can provide physical insight into the problem. The first...EPTS)*Ŗ) STPM *2. ’TP’ (CABS (ETPS)*Ŗ) STTHi2.*TP*(CARS(ETTS)*Ŗ) RETURN - 1 END 296 do APPENDIX 37 * SUBROUTINE SURFFY SUBROUTINE.SURF!? (KXl,YN1...D-Ai135 837 A USER’S MAiNUAfL FOR ELECTROMAGNETIC SURFACE PATCH (ESP) 1 /4 CODE VERSION 11 P.-(U) OHIO STATE UNIV COLUMBUS U CLAS ELECTROSCIENCE LAB E

Design and Evaluation of a Chamber Capable of Containing the Detonation Effects of 40 Pounds of TNT

DTIC Science & Technology

1975-11-01

Boiler and Pressure Vessel Code , 197A. For the girth welds, short lengths of 26-in.-dia. pipe were tacked to the vessel around the...and tensile tests meet the requirements of Section IX, ASHE Boiler and Pressure Vessel Code , 1974. Weld made by W. H. Stefanov ■.^^ w-^iiMaLwärt...Macro Results Kos, No Remarl.s The results of the bond and it^nsile tests met the requirements of Section IX, ASME Boiler and Pressure

A Mode Propagation Database Suitable for Code Validation Utilizing the NASA Glenn Advanced Noise Control Fan and Artificial Sources

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2014-01-01

The NASA Glenn Research Center's Advanced Noise Control Fan (ANCF) was developed in the early 1990s to provide a convenient test bed to measure and understand fan-generated acoustics, duct propagation, and radiation to the farfield. A series of tests were performed primarily for the use of code validation and tool validation. Rotating Rake mode measurements were acquired for parametric sets of: (i) mode blockage, (ii) liner insertion loss, (iii) short ducts, and (iv) mode reflection.

Investigation of Ionospheric Disturbances

DTIC Science & Technology

1977-01-28

Heikkila, D.M. Klumpar, J.D. Winningham, U. Fahleson, C.G. Falthammar, and A. Pederson ; "Rocket-Borne Particle, Field and Plasma Observations in the...S Arvny Sit ti-im Agvi- y ATTN: Code 7709, Withah A] l ITN: T1- hllhii ],it rl r"y AT’IN: ..cIdv 770. Klaun. I|i,,in ATTN: Code 7750, f. I -,Ihhr thi...ATTN: J. F. Frii,htaianiChto Rl -I1I9f R I, 1) Ass-lat , s ATTN: IH. II. loflloway, R1-20(16 I’N: Herbert .. Mitchell United Techrnilogips Corporal Ion

Single Event Upset Rate Estimates for a 16-K CMOS (Complementary Metal Oxide Semiconductor) SRAM (Static Random Access Memory).

DTIC Science & Technology

1986-09-30

4 . ~**..ft.. ft . - - - ft SI TABLES 9 I. SA32~40 Single Event Upset Test, 1140-MeV Krypton, 9/l8/8~4. . .. .. .. .. .. .16 II. CRUP Simulation...cosmic ray interaction analysis described in the remainder of this report were calculated using the CRUP computer code 3 modified for funneling. The... CRUP code requires, as inputs, the size of a depletion region specified as a retangular parallel piped with dimensions a 9 b S c, the effective funnel

Loss-of-flow-without-scram tests in Experimental Breeder Reactor-II and comparison with pretest predictions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, L.K.; Mohr, D.; Planchon, H.P.

This article discusses a series of successful loss-of-flow-without-scram tests conducted in Experimental Breeder Reactor-II (EBR-II), a metal-fueled, sodium-cooled fast reactor. These May 1985 tests demonstrated the capability of the EBR to reduce reactor power passively during a loss of flow and to maintain reactor temperatures within bounds without any reliance on an active safety system. The tests were run from reduced power to ensure that temperatures could be maintained well below the fuel-clad eutectic temperature. Good agreement was found between selected test data and pretest predictions made with the EBR-II system analysis code NATDEMO and the hot channel analysis codemore » HOTCHAN. The article also discusses safety assessments of the tests as well as modifications required on the EBR-II reactor safety system for conducting required on the EBR-II reactor safety system for the conducting the tests.« less

PRESTO-II: a low-level waste environmental transport and risk assessment code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fields, D.E.; Emerson, C.J.; Chester, R.O.

PRESTO-II (Prediction of Radiation Effects from Shallow Trench Operations) is a computer code designed for the evaluation of possible health effects from shallow-land and, waste-disposal trenches. The model is intended to serve as a non-site-specific screening model for assessing radionuclide transport, ensuing exposure, and health impacts to a static local population for a 1000-year period following the end of disposal operations. Human exposure scenarios considered include normal releases (including leaching and operational spillage), human intrusion, and limited site farming or reclamation. Pathways and processes of transit from the trench to an individual or population include ground-water transport, overland flow, erosion,more » surface water dilution, suspension, atmospheric transport, deposition, inhalation, external exposure, and ingestion of contaminated beef, milk, crops, and water. Both population doses and individual doses, as well as doses to the intruder and farmer, may be calculated. Cumulative health effects in terms of cancer deaths are calculated for the population over the 1000-year period using a life-table approach. Data are included for three example sites: Barnwell, South Carolina; Beatty, Nevada; and West Valley, New York. A code listing and example input for each of the three sites are included in the appendices to this report.« less

Performance Analysis, Modeling and Scaling of HPC Applications and Tools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatele, Abhinav

2016-01-13

E cient use of supercomputers at DOE centers is vital for maximizing system throughput, mini- mizing energy costs and enabling science breakthroughs faster. This requires complementary e orts along several directions to optimize the performance of scienti c simulation codes and the under- lying runtimes and software stacks. This in turn requires providing scalable performance analysis tools and modeling techniques that can provide feedback to physicists and computer scientists developing the simulation codes and runtimes respectively. The PAMS project is using time allocations on supercomputers at ALCF, NERSC and OLCF to further the goals described above by performing research alongmore » the following fronts: 1. Scaling Study of HPC applications; 2. Evaluation of Programming Models; 3. Hardening of Performance Tools; 4. Performance Modeling of Irregular Codes; and 5. Statistical Analysis of Historical Performance Data. We are a team of computer and computational scientists funded by both DOE/NNSA and DOE/ ASCR programs such as ECRP, XStack (Traleika Glacier, PIPER), ExaOSR (ARGO), SDMAV II (MONA) and PSAAP II (XPACC). This allocation will enable us to study big data issues when analyzing performance on leadership computing class systems and to assist the HPC community in making the most e ective use of these resources.« less

Rotorcraft Optimization Tools: Incorporating Rotorcraft Design Codes into Multi-Disciplinary Design, Analysis, and Optimization

NASA Technical Reports Server (NTRS)

Meyn, Larry A.

2018-01-01

One of the goals of NASA's Revolutionary Vertical Lift Technology Project (RVLT) is to provide validated tools for multidisciplinary design, analysis and optimization (MDAO) of vertical lift vehicles. As part of this effort, the software package, RotorCraft Optimization Tools (RCOTOOLS), is being developed to facilitate incorporating key rotorcraft conceptual design codes into optimizations using the OpenMDAO multi-disciplinary optimization framework written in Python. RCOTOOLS, also written in Python, currently supports the incorporation of the NASA Design and Analysis of RotorCraft (NDARC) vehicle sizing tool and the Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics II (CAMRAD II) analysis tool into OpenMDAO-driven optimizations. Both of these tools use detailed, file-based inputs and outputs, so RCOTOOLS provides software wrappers to update input files with new design variable values, execute these codes and then extract specific response variable values from the file outputs. These wrappers are designed to be flexible and easy to use. RCOTOOLS also provides several utilities to aid in optimization model development, including Graphical User Interface (GUI) tools for browsing input and output files in order to identify text strings that are used to identify specific variables as optimization input and response variables. This paper provides an overview of RCOTOOLS and its use

Infection and the Burn Patient,

DTIC Science & Technology

1990-10-01

Leading articles -T[--- Sr. J. Surg. 1990, Vol. 77, October, 1081- 1082 Ii’ ftELECTE f Infection and the burn patient 0U11901 Can ... the leopard...Distribution/ Availability Codes. Avail and/or Dlst Special 1082 Br. J. Surg., Vol. 77, No. 10, October 1990

Center for Parallel Optimization

DTIC Science & Technology

1993-09-30

BOLLING AFB DC 20332-0001 _ii _ 11. SUPPLEMENTARY NOTES 12a. DISTRIBUTION/ AVAILABILITY STATEMENT 12b. DISTRIBUTION CODE APPROVED FOR PUBLIC RELEASE...Machines Corporation, March 16-19, 1993 , A Branch- and-Bound Method for Mixed Integer Programming on the CM-.5 "* Dr. Roberto Musmanno, University of

38 CFR 1.924 - Suspension or revocation of eligibility for federal loans, loan insurance, loan guarantees...

Code of Federal Regulations, 2010 CFR

2010-07-01

... cause(s) of the delinquency and the likelihood that the person will resolve the delinquent debt; and (ii... General Counsel or Regional Counsel concerning the impact of the Bankruptcy Code, particularly 11 U.S.C...

5 CFR 581.104 - Moneys which are not subject to garnishment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... United States Code; (d) Grants; (e) Fellowships; (f) Education and vocational rehabilitation benefits for...: (1) In the case of civilian employees: (i) Uniform allowances; (ii) Travel and transportation... differentials; (vi) Foreign areas allowances; (vii) Education allowances for dependents; (viii) Separate...

Evaluating the Frequency of aac(6')-IIa, ant(2″)-I, intl1, and intl2 Genes in Aminoglycosides Resistant Klebsiella pneumoniae Isolates Obtained from Hospitalized Patients in Yazd, Iran.

PubMed

Mokhtari, Hesam; Eslami, Gilda; Zandi, Hengameh; Dehghan-Banadkouki, Amin; Vakili, Mahmood

2018-01-01

Klebsiella pneumoniae (K. pneumoniae) is an opportunistic pathogen that could be resistant to many antimicrobial agents. Resistance genes can be carried among gram-negative bacteria by integrons. Enzymatic inactivation is the most important mechanism of resistance to aminoglycosides. In this study, the frequencies of two important resistance gene aac(6')-II a and ant(2″)-I, and genes coding integrase I and II, in K. pneumoniae isolates resistant to aminoglycosides were evaluated. In this cross-sectional study, an attempt was made to assess the antibiotic susceptibility of 130 K. pneumoniae isolates obtained from different samples of patients hospitalized in training hospitals of Yazd evaluated by disk diffusion method. The frequencies of aac(6')-II a, ant(2″)-I, intl1 , and intl2 genes were determined by PCR method. Data were analyzed by chi-square method using SPSS software (Ver. 16). our results showed that resistance to gentamicin, tobramycin, kanamycin, and amikacin were 34.6, 33.8, 43.8, and 14.6%, respectively. The frequencies of aac (6')-II a, ant(2″)-I, intl1 , and intl2 genes were 44.6, 27.7, 90, and 0%, respectively. This study showed there are high frequencies of genes coding aminoglycosides resistance in K. pneumoniae isolates. Hence, it is very important to monitor and inhibit the spread of antibiotic resistance genes.

Financial Accounting and Reporting Improvement Concepts.

DTIC Science & Technology

1980-02-01

systems: coordination and nonlro m" f𔃾mannia systems- la_ 20. ABSTRACT (C a tgo *a n Fa.. ’" o I t nce so . y a, den ,A . blok M ) r a n g e p i a n a i...I NOV IS II0II Unclassified .. SECURITY CLSIIAX klq P.9 Dt "’~~~~-- kA ___________ O -eh awa UawOVd tI4A do NOIAV J.JiUV1 AJ|I¥fl*U 2M.0 ontinued J...800 North Quincy Street Arlington, Virginia 22217 r r .ut . o / - .. J .. . r Codes Attention: Dr. Thomas C. Varley Dear Sirs: sp RE: CONTRACT NO. 0014

Three-dimensional modeling of the Ca II H and K lines in the solar atmosphere

NASA Astrophysics Data System (ADS)

Bjørgen, Johan P.; Sukhorukov, Andrii V.; Leenaarts, Jorrit; Carlsson, Mats; de la Cruz Rodríguez, Jaime; Scharmer, Göran B.; Hansteen, Viggo H.

2018-03-01

Context. CHROMIS, a new imaging spectrometer at the Swedish 1-m Solar Telescope (SST), can observe the chromosphere in the H and K lines of Ca II at high spatial and spectral resolution. Accurate modeling as well as an understanding of the formation of these lines are needed to interpret the SST/CHROMIS observations. Such modeling is computationally challenging because these lines are influenced by strong departures from local thermodynamic equilibrium, three-dimensional radiative transfer, and partially coherent resonance scattering of photons. Aim. We aim to model the Ca II H and K lines in 3D model atmospheres to understand their formation and to investigate their diagnostic potential for probing the chromosphere. Methods: We model the synthetic spectrum of Ca II using the radiative transfer code Multi3D in three different radiation-magnetohydrodynamic model atmospheres computed with the Bifrost code. We classify synthetic intensity profiles according to their shapes and study how their features are related to the physical properties in the model atmospheres. We investigate whether the synthetic data reproduce the observed spatially-averaged line shapes, center-to-limb variation and compare this data with SST/CHROMIS images. Results: The spatially-averaged synthetic line profiles show too low central emission peaks, and too small separation between the peaks. The trends of the observed center-to-limb variation of the profiles properties are reproduced by the models. The Ca II H and K line profiles provide a temperature diagnostic of the temperature minimum and the temperature at the formation height of the emission peaks. The Doppler shift of the central depression is an excellent probe of the velocity in the upper chromosphere.

Whole genome sequence analysis of Geitlerinema sp. FC II unveils competitive edge of the strain in marine cultivation system for biofuel production.

PubMed

Batchu, Navish Kumar; Khater, Shradha; Patil, Sonal; Nagle, Vinod; Das, Gautam; Bhadra, Bhaskar; Sapre, Ajit; Dasgupta, Santanu

2018-03-05

A filamentous cyanobacteria, Geitlerinema sp. FC II, was isolated from marine algae culture pond at Reliance Industries Limited (RIL), India. The 6.7 Mb draft genome of FC II encodes for 6697 protein coding genes. Analysis of the whole genome sequence revealed presence of nif gene cluster, supporting its capability to fix atmospheric nitrogen. FC II genome contains two variants of sulfide:quinone oxidoreductases (SQR), which is a crucial elector donor in cyanobacterial metabolic processes. FC II is characterized by the presence of multiple CRISPR- Cas (Clustered Regularly Interspaced Short Palindrome Repeats - CRISPR associated proteins) clusters, multiple variants of genes encoding photosystem reaction centres, biosynthetic gene clusters of alkane, polyketides and non-ribosomal peptides. Presence of these pathways will help FC II in gaining an ecological advantage over other strains for biomass production in large scale cultivation system. Hence, FC II may be used for production of biofuel and other industrially important metabolites. Copyright © 2018 Elsevier Inc. All rights reserved.

Diabetes Mellitus Coding Training for Family Practice Residents.

PubMed

Urse, Geraldine N

2015-07-01

Although physicians regularly use numeric coding systems such as the International Classification of Diseases, Ninth Revision, Clinical Modification (ICD-9-CM) to describe patient encounters, coding errors are common. One of the most complicated diagnoses to code is diabetes mellitus. The ICD-9-CM currently has 39 separate codes for diabetes mellitus; this number will be expanded to more than 50 with the introduction of ICD-10-CM in October 2015. To assess the effect of a 1-hour focused presentation on ICD-9-CM codes on diabetes mellitus coding. A 1-hour focused lecture on the correct use of diabetes mellitus codes for patient visits was presented to family practice residents at Doctors Hospital Family Practice in Columbus, Ohio. To assess resident knowledge of the topic, a pretest and posttest were given to residents before and after the lecture, respectively. Medical records of all patients with diabetes mellitus who were cared for at the hospital 6 weeks before and 6 weeks after the lecture were reviewed and compared for the use of diabetes mellitus ICD-9 codes. Eighteen residents attended the lecture and completed the pretest and posttest. The mean (SD) percentage of correct answers was 72.8% (17.1%) for the pretest and 84.4% (14.6%) for the posttest, for an improvement of 11.6 percentage points (P≤.035). The percentage of total available codes used did not substantially change from before to after the lecture, but the use of the generic ICD-9-CM code for diabetes mellitus type II controlled (250.00) declined (58 of 176 [33%] to 102 of 393 [26%]) and the use of other codes increased, indicating a greater variety in codes used after the focused lecture. After a focused lecture on diabetes mellitus coding, resident coding knowledge improved. Review of medical record data did not reveal an overall change in the number of diabetic codes used after the lecture but did reveal a greater variety in the codes used.

Novel cell-based assay for detection of thyroid receptor beta-interacting environmental contaminants.

PubMed

Stavreva, Diana A; Varticovski, Lyuba; Levkova, Ludmila; George, Anuja A; Davis, Luke; Pegoraro, Gianluca; Blazer, Vicki; Iwanowicz, Luke; Hager, Gordon L

2016-08-10

Even though the presence of endocrine disrupting chemicals (EDCs) with thyroid hormone (TH)-like activities in the environment is a major health concern, the methods for their efficient detection and monitoring are still limited. Here we describe a novel cell assay, based on the translocation of a green fluorescent protein (GFP)-tagged chimeric molecule of glucocorticoid receptor (GR) and the thyroid receptor beta (TRβ) from the cytoplasm to the nucleus in the presence of TR ligands. Unlike the constitutively nuclear TRβ, this GFP-GR-TRβ chimera is cytoplasmic in the absence of hormone while translocating to the nucleus in a time- and concentration-dependent manner upon stimulation with triiodothyronine (T3) and thyroid hormone analogue, TRIAC, while the reverse triiodothyronine (3,3',5'-triiodothyronine, or rT3) was inactive. Moreover, GFP-GR-TRβ chimera does not show any cross-reactivity with the GR-activating hormones, thus providing a clean system for the screening of TR beta-interacting EDCs. Using this assay, we demonstrated that Bisphenol A (BPA) and 3,3',5,5'-Tetrabromobisphenol (TBBPA) induced GFP-GR-TRβ translocation at micro molar concentrations. We screened over 100 concentrated water samples from different geographic locations in the United States and detected a low, but reproducible contamination in 53% of the samples. This system provides a novel high-throughput approach for screening for endocrine disrupting chemicals (EDCs) interacting with TR beta. Published by Elsevier Ireland Ltd.

Novel cell-based assay for detection of thyroid receptor beta-interacting environmental contaminants

USGS Publications Warehouse

Stavreva, Diana A.; Varticovski, Lyuba; Levkova, Ludmila; George, Anuja A.; Davis, Luke; Pegoraro, Gianluca; Blazer, Vicki S.; Iwanowicz, Luke R.; Hager, Gordon L.

2016-01-01

Even though the presence of endocrine disrupting chemicals (EDCs) with thyroid hormone (TH)-like activities in the environment is a major health concern, the methods for their efficient detection and monitoring are still limited. Here we describe a novel cell assay, based on the translocation of a green fluorescent protein (GFP)—tagged chimeric molecule of glucocorticoid receptor (GR) and the thyroid receptor beta (TRβ) from the cytoplasm to the nucleus in the presence of TR ligands. Unlike the constitutively nuclear TRβ, this GFP-GR-TRβ chimera is cytoplasmic in the absence of hormone while translocating to the nucleus in a time- and concentration-dependent manner upon stimulation with triiodothyronine (T3) and thyroid hormone analogue, TRIAC, while the reverse triiodothyronine (3,3′,5′-triiodothyronine, or rT3) was inactive. Moreover, GFP-GR-TRβ chimera does not show any cross-reactivity with the GR-activating hormones, thus providing a clean system for the screening of TR beta-interacting EDCs. Using this assay, we demonstrated that Bisphenol A (BPA) and 3,3′,5,5′-Tetrabromobisphenol (TBBPA) induced GFP-GR-TRβ translocation at micro molar concentrations. We screened over 100 concentrated water samples from different geographic locations in the United States and detected a low, but reproducible contamination in 53% of the samples. This system provides a novel high-throughput approach for screening for endocrine disrupting chemicals (EDCs) interacting with TR beta.

Novel cell-based assay for detection of thyroid receptor beta-interacting environmental contaminants

PubMed Central

Stavreva, Diana A.; Varticovski, Lyuba; Levkova, Ludmila; George, Anuja A.; Davis, Luke; Pegoraro, Gianluca; Blazer, Vicki; Iwanowicz, Luke; Hager, Gordon L.

2016-01-01

Even though the presence of endocrine disrupting chemicals (EDCs) with thyroid hormone (TH)-like activities in the environment is a major health concern, the methods for their efficient detection and monitoring are still limited. Here we describe a novel cell assay, based on the translocation of a green fluorescent protein (GFP) - tagged chimeric molecule of glucocorticoid receptor (GR) and the thyroid receptor beta (TRβ) from the cytoplasm to the nucleus in the presence of TR ligands. Unlike the constitutively nuclear TRβ, this GFP-GR-TRβ chimera is cytoplasmic in the absence of hormone while translocating to the nucleus in a time- and concentration-dependent manner upon stimulation with triiodothyronine (T3) and thyroid hormone analogue, TRIAC, while the reverse triiodothyronine (3,3′,5′-triiodothyronine, or rT3) was inactive. Moreover, GFP-GR-TRβ chimera does not show any cross-reactivity with the GR-activating hormones, thus providing a clean system for the screening of TR beta -interacting EDCs. Using this assay, we demonstrated that Bisphenol A (BPA) and 3,3′,5,5′-Tetrabromobisphenol (TBBPA) induced GFP-GR-TRβ translocation at micro molar concentrations. We screened over 100 concentrated water samples from different geographic locations in the United States and detected a low, but reproducible contamination in 53 % of the samples. This system provides a novel high-throughput approach for screening for endocrine disrupting chemicals (EDCs) interacting with TR beta. PMID:27528272

Development of Yield and Tensile Strength Design Curves for Alloy 617

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nancy Lybeck; T. -L. Sham

2013-10-01

The U.S. Department of Energy Very High Temperature Reactor Program is acquiring data in preparation for developing an Alloy 617 Code Case for inclusion in the nuclear section of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel (B&PV) Code. A draft code case was previously developed, but effort was suspended before acceptance by ASME. As part of the draft code case effort, a database was compiled of yield and tensile strength data from tests performed in air. Yield strength and tensile strength at temperature are used to set time independent allowable stress for construction materials in B&PVmore » Code, Section III, Subsection NH. The yield and tensile strength data used for the draft code case has been augmented with additional data generated by Idaho National Laboratory and Oak Ridge National Laboratory in the U.S. and CEA in France. The standard ASME Section II procedure for generating yield and tensile strength at temperature is presented, along with alternate methods that accommodate the change in temperature trends seen at high temperatures, resulting in a more consistent design margin over the temperature range of interest.« less

Recent Progress and Future Plans for Fusion Plasma Synthetic Diagnostics Platform

NASA Astrophysics Data System (ADS)

Shi, Lei; Kramer, Gerrit; Tang, William; Tobias, Benjamin; Valeo, Ernest; Churchill, Randy; Hausammann, Loic

2015-11-01

The Fusion Plasma Synthetic Diagnostics Platform (FPSDP) is a Python package developed at the Princeton Plasma Physics Laboratory. It is dedicated to providing an integrated programmable environment for applying a modern ensemble of synthetic diagnostics to the experimental validation of fusion plasma simulation codes. The FPSDP will allow physicists to directly compare key laboratory measurements to simulation results. This enables deeper understanding of experimental data, more realistic validation of simulation codes, quantitative assessment of existing diagnostics, and new capabilities for the design and optimization of future diagnostics. The Fusion Plasma Synthetic Diagnostics Platform now has data interfaces for the GTS and XGC-1 global particle-in-cell simulation codes with synthetic diagnostic modules including: (i) 2D and 3D Reflectometry; (ii) Beam Emission Spectroscopy; and (iii) 1D Electron Cyclotron Emission. Results will be reported on the delivery of interfaces for the global electromagnetic PIC code GTC, the extended MHD M3D-C1 code, and the electromagnetic hybrid NOVAK eigenmode code. Progress toward development of a more comprehensive 2D Electron Cyclotron Emission module will also be discussed. This work is supported by DOE contract #DEAC02-09CH11466.

40 CFR 261.4 - Exclusions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... exclusion from the definition of solid waste. (18) Petrochemical recovered oil from an associated organic... for benzene (§ 261.24, waste code D018); and (ii) The oil generated by the organic chemical... petroleum refining process. An “associated organic chemical manufacturing facility” is a facility where the...

Iso-chemical potential trajectories in the P-T plane for He II

NASA Technical Reports Server (NTRS)

Maytal, B.; Nissen, J. A.; Van Sciver, S. W.

1990-01-01

Trajectories of constant chemical potential in the P-T plane serve as an integral formulation of London's equation. The trajectories are useful for analysis and synthesis of fountain effect pump performance. A family of trajectories is generated from available numerical codes.

Detection of sinkholes or anomalies using full seismic wave fields : phase II.

DOT National Transportation Integrated Search

2016-08-01

A new 2-D Full Waveform Inversion (FWI) software code was developed to characterize layering and anomalies beneath the ground surface using seismic testing. The software is capable of assessing the shear and compression wave velocities (Vs and Vp) fo...

Department of Interior Semiannual Regulatory Agenda

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-26

... INTERIOR (DOI) DEPARTMENT OF THE INTERIOR Office of the Secretary 25 CFR Ch. I 30 CFR Chs. II and VII 36... Plugging and Platform Decommissioning 1010-AD61 Department of the Interior (DOI) Final Rule Stage United...-AX19 BILLING CODE 4310--55--S [[Page 21817

42 CFR 433.37 - Reporting provider payments to Internal Revenue Service.

Code of Federal Regulations, 2010 CFR

2010-10-01

... identification of providers by— (1) Social security number if— (i) The provider is in solo practice; or (ii) The... security number or employer identification number. ... identification number for all other providers. (c) Compliance with section 6041 of the Internal Revenue Code. The...

Unsupervised Transfer Learning via Multi-Scale Convolutional Sparse Coding for Biomedical Applications

PubMed Central

Chang, Hang; Han, Ju; Zhong, Cheng; Snijders, Antoine M.; Mao, Jian-Hua

2017-01-01

The capabilities of (I) learning transferable knowledge across domains; and (II) fine-tuning the pre-learned base knowledge towards tasks with considerably smaller data scale are extremely important. Many of the existing transfer learning techniques are supervised approaches, among which deep learning has the demonstrated power of learning domain transferrable knowledge with large scale network trained on massive amounts of labeled data. However, in many biomedical tasks, both the data and the corresponding label can be very limited, where the unsupervised transfer learning capability is urgently needed. In this paper, we proposed a novel multi-scale convolutional sparse coding (MSCSC) method, that (I) automatically learns filter banks at different scales in a joint fashion with enforced scale-specificity of learned patterns; and (II) provides an unsupervised solution for learning transferable base knowledge and fine-tuning it towards target tasks. Extensive experimental evaluation of MSCSC demonstrates the effectiveness of the proposed MSCSC in both regular and transfer learning tasks in various biomedical domains. PMID:28129148

Research and development studies for MHD/coal power flow train components. Part II. Diagnostics and instrumentation MHD channel combutor. Progres report. [Flow calculations for combustors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bloom, M.H.; Lederman, S.; Sforza, P.

1980-01-01

This is Part II of the Technical Progress Report on Tasks II-IV of the subject contract. It deals sequentially with Diagnostics and Instrumentation, the MHD Channel and the Combustor. During this period, a significant effort has gone into establishing a schematic design of a laser diagnostic system which can be applied to the flow-train of the MHD system, and to acquiring, assembling and shaking down a laboratory set-up upon which a prototype can be based. With further reference to the MHD Channel, a model analysis has been initiated of the two-dimensional MHD boundary layer between two electrodes in the limitmore » of small magnetic Reynolds numbers with negligible effect of the flow on the applied magnetic field. An objective of this model study is the assessment of variations in initial conditions on the boundary layer behavior. Finally, the problem of combustion modeling has been studied on an initial basis. The open reports on this subject depict a high degree of empiricism, centering attention on global behavior mainly. A quasi-one-dimensional model code has been set-up to check some of the existing estimates. Also a code for equilibrium combustion has been activated.« less

Experimental studies and simulations of hydrogen pellet ablation in the stellarator TJ-II

NASA Astrophysics Data System (ADS)

Panadero, N.; McCarthy, K. J.; Koechl, F.; Baldzuhn, J.; Velasco, J. L.; Combs, S. K.; de la Cal, E.; García, R.; Hernández Sánchez, J.; Silvagni, D.; Turkin, Y.; TJ-II Team; W7-X Team

2018-02-01

Plasma core fuelling is a key issue for the development of steady-state scenarios in large magnetically-confined fusion devices, in particular for helical-type machines. At present, cryogenic pellet injection is the most promising technique for efficient fuelling. Here, pellet ablation and fuelling efficiency experiments, using a compact pellet injector, are carried out in electron cyclotron resonance and neutral beam injection heated plasmas of the stellarator TJ-II. Ablation profiles are reconstructed from light emissions collected by silicon photodiodes and a fast-frame camera system, under the assumptions that such emissions are loosely related to the ablation rate and that pellet radial acceleration is negligible. In addition, pellet particle deposition and fuelling efficiency are determined using density profiles provided by a Thomson scattering system. Furthermore, experimental results are compared with ablation and deposition profiles provided by the HPI2 pellet code, which is adapted here for the stellarators Wendelstein 7-X (W7-X) and TJ-II. Finally, the HPI2 code is used to simulate ablation and deposition profiles for pellets of different sizes and velocities injected into relevant W7-X plasma scenarios, while estimating the plasmoid drift and the fuelling efficiency of injections made from two W7-X ports.

Reproducing a Prospective Clinical Study as a Computational Retrospective Study in MIMIC-II.

PubMed

Kury, Fabrício S P; Huser, Vojtech; Cimino, James J

2015-01-01

In this paper we sought to reproduce, as a computational retrospective study in an EHR database (MIMIC-II), a recent large prospective clinical study: the 2013 publication, by the Japanese Association for Acute Medicine (JAAM), about disseminated intravascular coagulation, in the journal Critical Care (PMID: 23787004). We designed in SQL and Java a set of electronic phenotypes that reproduced the study's data sampling, and used R to perform the same statistical inference procedures. All produced source code is available online at https://github.com/fabkury/paamia2015. Our program identified 2,257 eligible patients in MIMIC-II, and the results remarkably agreed with the prospective study. A minority of the needed data elements was not found in MIMIC-II, and statistically significant inferences were possible in the majority of the cases.

Self-consistent modeling of electron cyclotron resonance ion sources

NASA Astrophysics Data System (ADS)

Girard, A.; Hitz, D.; Melin, G.; Serebrennikov, K.; Lécot, C.

2004-05-01

In order to predict the performances of electron cyclotron resonance ion source (ECRIS), it is necessary to perfectly model the different parts of these sources: (i) magnetic configuration; (ii) plasma characteristics; (iii) extraction system. The magnetic configuration is easily calculated via commercial codes; different codes also simulate the ion extraction, either in two dimension, or even in three dimension (to take into account the shape of the plasma at the extraction influenced by the hexapole). However the characteristics of the plasma are not always mastered. This article describes the self-consistent modeling of ECRIS: we have developed a code which takes into account the most important construction parameters: the size of the plasma (length, diameter), the mirror ratio and axial magnetic profile, whether a biased probe is installed or not. These input parameters are used to feed a self-consistent code, which calculates the characteristics of the plasma: electron density and energy, charge state distribution, plasma potential. The code is briefly described, and some of its most interesting results are presented. Comparisons are made between the calculations and the results obtained experimentally.

Spatial versus sequential correlations for random access coding

NASA Astrophysics Data System (ADS)

Tavakoli, Armin; Marques, Breno; Pawłowski, Marcin; Bourennane, Mohamed

2016-03-01

Random access codes are important for a wide range of applications in quantum information. However, their implementation with quantum theory can be made in two very different ways: (i) by distributing data with strong spatial correlations violating a Bell inequality or (ii) using quantum communication channels to create stronger-than-classical sequential correlations between state preparation and measurement outcome. Here we study this duality of the quantum realization. We present a family of Bell inequalities tailored to the task at hand and study their quantum violations. Remarkably, we show that the use of spatial and sequential quantum correlations imposes different limitations on the performance of quantum random access codes: Sequential correlations can outperform spatial correlations. We discuss the physics behind the observed discrepancy between spatial and sequential quantum correlations.

TRACKING SIMULATIONS NEAR HALF-INTEGER RESONANCE AT PEP-II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nosochkov, Yuri

2003-05-13

Beam-beam simulations predict that PEP-II luminosity can be increased by operating the horizontal betatron tune near and above a half-integer resonance. However, effects of the resonance and its synchrotron sidebands significantly enhance betatron and chromatic perturbations which tend to reduce dynamic aperture. In the study, chromatic variation of horizontal tune near the resonance was minimized by optimizing local sextupoles in the Interaction Region. Dynamic aperture was calculated using tracking simulations in LEGO code. Dependence of dynamic aperture on the residual orbit, dispersion and {beta} distortion after correction was investigated.

42 CFR 422.4 - Types of MA plans.

Code of Federal Regulations, 2010 CFR

2010-10-01

... availability, service area, and quality. (ii) Coordinated care plans may include mechanisms to control... requirements of sections 138 and 220 of the Internal Revenue Code. (3) MA private fee-for-service plan. An MA... Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...

44 CFR 206.118 - Disposal of housing units.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Federal Assistance to..., has a site that complies with local codes and ordinances and part 9 of this Title. (ii) Adjustment to... providing temporary housing to disaster victims in major disasters and emergencies. As a condition of the...

7 CFR 1980.302 - Definitions and abbreviations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... codes listed in exhibit E to subpart A of part 1924 applicable to single family residential construction...: (i) Self-care, (ii) Receptive and expressive language, (iii) Learning, (iv) Mobility, (v) Self... Lender on behalf of the borrower. Lender. The organization making, holding, and/or servicing the loan...

7 CFR 1980.302 - Definitions and abbreviations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... codes listed in exhibit E to subpart A of part 1924 applicable to single family residential construction...: (i) Self-care, (ii) Receptive and expressive language, (iii) Learning, (iv) Mobility, (v) Self... Lender on behalf of the borrower. Lender. The organization making, holding, and/or servicing the loan...

48 CFR 52.227-20 - Rights in Data-SBIR Program.

Code of Federal Regulations, 2011 CFR

2011-10-01

... series of operations; and (ii) Recorded information comprising source code listings, design details...) Means (i) Computer programs that comprise a series of instructions, rules, routines, or statements... small business innovation research contract issued under the authority of 15 U.S.C. 638, which data are...

48 CFR 52.227-20 - Rights in Data-SBIR Program.

Code of Federal Regulations, 2010 CFR

2010-10-01

... series of operations; and (ii) Recorded information comprising source code listings, design details...) Means (i) Computer programs that comprise a series of instructions, rules, routines, or statements... small business innovation research contract issued under the authority of 15 U.S.C. 638, which data are...

48 CFR 52.227-20 - Rights in Data-SBIR Program.

Code of Federal Regulations, 2013 CFR

2013-10-01

... series of operations; and (ii) Recorded information comprising source code listings, design details...) Means (i) Computer programs that comprise a series of instructions, rules, routines, or statements... small business innovation research contract issued under the authority of 15 U.S.C. 638, which data are...

48 CFR 52.227-20 - Rights in Data-SBIR Program.

Code of Federal Regulations, 2012 CFR

2012-10-01

... series of operations; and (ii) Recorded information comprising source code listings, design details...) Means (i) Computer programs that comprise a series of instructions, rules, routines, or statements... small business innovation research contract issued under the authority of 15 U.S.C. 638, which data are...

48 CFR 52.227-20 - Rights in Data-SBIR Program.

Code of Federal Regulations, 2014 CFR

2014-10-01

... series of operations; and (ii) Recorded information comprising source code listings, design details...) Means (i) Computer programs that comprise a series of instructions, rules, routines, or statements... small business innovation research contract issued under the authority of 15 U.S.C. 638, which data are...

40 CFR 272.1151 - State-administered program: Final authorization.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., P.O. Box 64526, St. Paul, Minnesota 55164-0526. (ii) Michigan Administrative Code, Rules 299.9101... seq. (c) Statement of Legal Authority. The Michigan Attorney General's Statements for final authorization signed by the Attorney General of Michigan on October 25, 1985, and supplements to that Statement...

40 CFR 63.1561 - Am I subject to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... American Industry Classification (NAIC) code 32411, and used mainly for: (i) Producing transportation fuels (such as gasoline, diesel fuels, and jet fuels), heating fuels (such as kerosene, fuel gas distillate, and fuel oils), or lubricants; (ii) Separating petroleum; or (iii) Separating, cracking, reacting, or...

40 CFR 63.1561 - Am I subject to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... American Industry Classification (NAIC) code 32411, and used mainly for: (i) Producing transportation fuels (such as gasoline, diesel fuels, and jet fuels), heating fuels (such as kerosene, fuel gas distillate, and fuel oils), or lubricants; (ii) Separating petroleum; or (iii) Separating, cracking, reacting, or...

40 CFR 63.1561 - Am I subject to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... American Industry Classification (NAIC) code 32411, and used mainly for: (i) Producing transportation fuels (such as gasoline, diesel fuels, and jet fuels), heating fuels (such as kerosene, fuel gas distillate, and fuel oils), or lubricants; (ii) Separating petroleum; or (iii) Separating, cracking, reacting, or...

26 CFR 1.56(g)-0 - Table of Contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Treatment of death benefits. (vi) Other rules. (A) Term life insurance contracts without net surrender... for adjusted current earnings. (5) General rule for applying Internal Revenue Code provisions in...) Property subject to new ACRS. (i) In general. (ii) Rules for computing the depreciation deduction. (iii...

Subgroup A : nuclear model codes report to the Sixteenth Meeting of the WPEC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Talou, P.; Chadwick, M. B.; Dietrich, F. S.

2004-01-01

The Subgroup A activities focus on the development of nuclear reaction models and codes, used in evaluation work for nuclear reactions from the unresolved energy region up to the pion threshold production limit, and for target nuclides from the low teens and heavier. Much of the efforts are devoted by each participant to the continuing development of their own Institution codes. Progresses in this arena are reported in detail for each code in the present document. EMPIRE-II is of public access. The release of the TALYS code has been announced for the ND2004 Conference in Santa Fe, NM, October 2004.more » McGNASH is still under development and is not expected to be released in the very near future. In addition, Subgroup A members have demonstrated a growing interest in working on common modeling and codes capabilities, which would significantly reduce the amount of duplicate work, help manage efficiently the growing lines of existing codes, and render codes inter-comparison much easier. A recent and important activity of the Subgroup A has therefore been to develop the framework and the first bricks of the ModLib library, which is constituted of mostly independent pieces of codes written in Fortran 90 (and above) to be used in existing and future nuclear reaction codes. Significant progresses in the development of ModLib have been made during the past year. Several physics modules have been added to the library, and a few more have been planned in detail for the coming year.« less

Determination of the Complex Elastic Moduli of Materials Using A Free- Free Bar Technique

DTIC Science & Technology

1994-03-01

LCDR, Dr. D. L alner 1 Dept. of Physics (Code PH) Naval Postgrdumt School Monterey, CA 93943 10 . Cgimd Ofric. Naval Reserh Labrary ATI’N: Dr. N...Postgraduate School ( fAp~hicbl) Naval Postgraduate School 6c. ADDRESS MclY- $Mae, 02t c7;w 3 7b. ADDRESS (city, MUk and ii? code) Mogntere CA 93943-5=0...Monery CA 93943-5000 Sa. NAME OF FUNDDOISIONS0R]NG G. OFMiCE SYMBOL 9. FUU1ENIICMN IDTFCTONNUMBER ORGANUAT1ON j (If Appkiabie) NSWC. CRANE. NPS

DIVWAG Model Documentation. Volume II. Programmer/Analyst Manual. Part 5.

DTIC Science & Technology

1976-07-01

Words Number Mission type: I=DAFS; 2= CAS 1 8 Estimated X coordinate of target 1 9 Estimated Y coordinate of target 1 10 Reject code: 0-mission unit... CAS 1 8 Abort indicator: O-no abort; 1-abort 1 9 X coordinate of target 1 10 " :oordinate of target 1 11 Aircraft munitions item code 6 12-17 Aircraft...L300 CALL TRNSMT U. TO TRANSMIT FIRST BLOCK OF DATA L100 YES REQUEST FOR INPU? LIOI CA " TRAN21I TO TRANSMIT LAST BLOCK OF DATA Figure VII-3-B- 10

NEBULAR: Spectrum synthesis for mixed hydrogen-helium gas in ionization equilibrium

NASA Astrophysics Data System (ADS)

Schirmer, Mischa

2016-08-01

NEBULAR synthesizes the spectrum of a mixed hydrogen helium gas in collisional ionization equilibrium. It is not a spectral fitting code, but it can be used to resample a model spectrum onto the wavelength grid of a real observation. It supports a wide range of temperatures and densities. NEBULAR includes free-free, free-bound, two-photon and line emission from HI, HeI and HeII. The code will either return the composite model spectrum, or, if desired, the unrescaled atomic emission coefficients. It is written in C++ and depends on the GNU Scientific Library (GSL).

Integration of Rotor Aerodynamic Optimization with the Conceptual Design of a Large Civil Tiltrotor

NASA Technical Reports Server (NTRS)

Acree, C. W., Jr.

2010-01-01

Coupling of aeromechanics analysis with vehicle sizing is demonstrated with the CAMRAD II aeromechanics code and NDARC sizing code. The example is optimization of cruise tip speed with rotor/wing interference for the Large Civil Tiltrotor (LCTR2) concept design. Free-wake models were used for both rotors and the wing. This report is part of a NASA effort to develop an integrated analytical capability combining rotorcraft aeromechanics, structures, propulsion, mission analysis, and vehicle sizing. The present paper extends previous efforts by including rotor/wing interference explicitly in the rotor performance optimization and implicitly in the sizing.

Complete plastid genome sequence of Daucus carota: implications for biotechnology and phylogeny of angiosperms.

PubMed

Ruhlman, Tracey; Lee, Seung-Bum; Jansen, Robert K; Hostetler, Jessica B; Tallon, Luke J; Town, Christopher D; Daniell, Henry

2006-08-31

Carrot (Daucus carota) is a major food crop in the US and worldwide. Its capacity for storage and its lifecycle as a biennial make it an attractive species for the introduction of foreign genes, especially for oral delivery of vaccines and other therapeutic proteins. Until recently efforts to express recombinant proteins in carrot have had limited success in terms of protein accumulation in the edible tap roots. Plastid genetic engineering offers the potential to overcome this limitation, as demonstrated by the accumulation of BADH in chromoplasts of carrot taproots to confer exceedingly high levels of salt resistance. The complete plastid genome of carrot provides essential information required for genetic engineering. Additionally, the sequence data add to the rapidly growing database of plastid genomes for assessing phylogenetic relationships among angiosperms. The complete carrot plastid genome is 155,911 bp in length, with 115 unique genes and 21 duplicated genes within the IR. There are four ribosomal RNAs, 30 distinct tRNA genes and 18 intron-containing genes. Repeat analysis reveals 12 direct and 2 inverted repeats > or = 30 bp with a sequence identity > or = 90%. Phylogenetic analysis of nucleotide sequences for 61 protein-coding genes using both maximum parsimony (MP) and maximum likelihood (ML) were performed for 29 angiosperms. Phylogenies from both methods provide strong support for the monophyly of several major angiosperm clades, including monocots, eudicots, rosids, asterids, eurosids II, euasterids I, and euasterids II. The carrot plastid genome contains a number of dispersed direct and inverted repeats scattered throughout coding and non-coding regions. This is the first sequenced plastid genome of the family Apiaceae and only the second published genome sequence of the species-rich euasterid II clade. Both MP and ML trees provide very strong support (100% bootstrap) for the sister relationship of Daucus with Panax in the euasterid II clade. These results provide the best taxon sampling of complete chloroplast genomes and the strongest support yet for the sister relationship of Caryophyllales to the asterids. The availability of the complete plastid genome sequence should facilitate improved transformation efficiency and foreign gene expression in carrot through utilization of endogenous flanking sequences and regulatory elements.

Solar proton exposure of an ICRU sphere within a complex structure part II: Ray-trace geometry.

PubMed

Slaba, Tony C; Wilson, John W; Badavi, Francis F; Reddell, Brandon D; Bahadori, Amir A

2016-06-01

A computationally efficient 3DHZETRN code with enhanced neutron and light ion (Z ≤ 2) propagation was recently developed for complex, inhomogeneous shield geometry described by combinatorial objects. Comparisons were made between 3DHZETRN results and Monte Carlo (MC) simulations at locations within the combinatorial geometry, and it was shown that 3DHZETRN agrees with the MC codes to the extent they agree with each other. In the present report, the 3DHZETRN code is extended to enable analysis in ray-trace geometry. This latest extension enables the code to be used within current engineering design practices utilizing fully detailed vehicle and habitat geometries. Through convergence testing, it is shown that fidelity in an actual shield geometry can be maintained in the discrete ray-trace description by systematically increasing the number of discrete rays used. It is also shown that this fidelity is carried into transport procedures and resulting exposure quantities without sacrificing computational efficiency. Published by Elsevier Ltd.

Comparison of EGS4 and MCNP Monte Carlo codes when calculating radiotherapy depth doses.

PubMed

Love, P A; Lewis, D G; Al-Affan, I A; Smith, C W

1998-05-01

The Monte Carlo codes EGS4 and MCNP have been compared when calculating radiotherapy depth doses in water. The aims of the work were to study (i) the differences between calculated depth doses in water for a range of monoenergetic photon energies and (ii) the relative efficiency of the two codes for different electron transport energy cut-offs. The depth doses from the two codes agree with each other within the statistical uncertainties of the calculations (1-2%). The relative depth doses also agree with data tabulated in the British Journal of Radiology Supplement 25. A discrepancy in the dose build-up region may by attributed to the different electron transport algorithims used by EGS4 and MCNP. This discrepancy is considerably reduced when the improved electron transport routines are used in the latest (4B) version of MCNP. Timing calculations show that EGS4 is at least 50% faster than MCNP for the geometries used in the simulations.

Timing Analysis with INTEGRAL: Comparing Different Reconstruction Algorithms

NASA Technical Reports Server (NTRS)

Grinberg, V.; Kreykenboehm, I.; Fuerst, F.; Wilms, J.; Pottschmidt, K.; Bel, M. Cadolle; Rodriquez, J.; Marcu, D. M.; Suchy, S.; Markowitz, A.;

26 CFR 54.4975-11 - “ESOP” requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... section 401(a) of the Code, relating to requirements for plans established for the exclusive benefit of... from a particular security holder at an indefinite time determined upon the happening of an event such... and exempt loan in the event of default. (ii) Individual annual contribution limitation. An ESOP will...

40 CFR 92.705 - Remedial plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Recall Regulations § 92.705 Remedial plan. (a) When any... adequate supply of parts will be available to initiate the repair campaign, the percentage of the total... intact. (3) The label shall contain: (i) The recall campaign number; and (ii) A code designating the...

40 CFR 85.1803 - Remedial Plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... POLLUTION FROM MOBILE SOURCES Recall Regulations § 85.1803 Remedial Plan. (a) When any manufacturer is... the total parts requirement of each person who is to perform the repair under the remedial plan to be...: (i) The recall campaign number; and (ii) A code designating the campaign facility at which the repair...

29 CFR 1917.3 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-07-01

...). For information on the availability of this material at NARA, telephone: 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Also, the material..., American National Standard for Personal Protection—Protective Footwear; IBR approved for § 1917.94(b)(1)(ii...

29 CFR 1917.3 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-07-01

...). For information on the availability of this material at NARA, telephone: 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Also, the material..., American National Standard for Personal Protection—Protective Footwear; IBR approved for § 1917.94(b)(1)(ii...

29 CFR 1917.3 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-07-01

...). For information on the availability of this material at NARA, telephone: 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Also, the material..., American National Standard for Personal Protection—Protective Footwear; IBR approved for § 1917.94(b)(1)(ii...

39 CFR 241.3 - Discontinuance of post offices.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... These rules are designed to ensure that the reasons leading a district manager, Customer Service and... originally assigned to the discontinued post office may be changed if the responsible district manager... to the discontinued post office. (ii) If the ZIP Code is changed and the parent post office covers...

Color Your Classroom II. A Math Curriculum Guide.

ERIC Educational Resources Information Center

Mississippi State Dept. of Education, Jackson.

This math curriculum guide, correlated with the numerical coding of the Math Skills List published by the Migrant Student Record Transfer System, covers 10 learning areas: readiness, number meaning, whole numbers, fractions, decimals, percent, measurement, geometry, probability and statistics, and sets. Each exercise is illustrated by a large…

7 CFR 1206.30 - Establishment and membership.

Code of Federal Regulations, 2011 CFR

2011-01-01

... INFORMATION Mango Promotion, Research, and Information Order Definitions National Mango Promotion Board § 1206... on the volume of mangos imported into the Customs Districts identified by their name and Code Number... seats for District I, three seats for District II, two seats for District III, and one seat for District...

7 CFR 1206.30 - Establishment and membership.

Code of Federal Regulations, 2014 CFR

2014-01-01

... INFORMATION Mango Promotion, Research, and Information Order Definitions National Mango Promotion Board § 1206... name and Code Number as defined in the Harmonized Tariff Schedule of the United States. The initial allocation will be two seats for District I, three seats for District II, two seats for District III, and one...

7 CFR 762.120 - Applicant eligibility.

Code of Federal Regulations, 2011 CFR

2011-01-01

... three occasions on or prior to April 4, 1996; or (ii) Any occasion after April 4, 1996. (2) The... Code; or (iii) Received debt forgiveness on not more than one occasion after April 4, 1996, resulting... received debt forgiveness on that debt within three years after the designation of such emergency meet this...

7 CFR 762.120 - Applicant eligibility.

Code of Federal Regulations, 2013 CFR

2013-01-01

... three occasions on or prior to April 4, 1996; or (ii) Any occasion after April 4, 1996. (2) The... Code; or (iii) Received debt forgiveness on not more than one occasion after April 4, 1996, resulting... received debt forgiveness on that debt within three years after the designation of such emergency meet this...

7 CFR 1206.30 - Establishment and membership.

Code of Federal Regulations, 2012 CFR

2012-01-01

... INFORMATION Mango Promotion, Research, and Information Order Definitions National Mango Promotion Board § 1206... name and Code Number as defined in the Harmonized Tariff Schedule of the United States. The initial allocation will be two seats for District I, three seats for District II, two seats for District III, and one...

42 CFR 3.212 - Nonidentification of patient safety work product.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., characteristic, or code except as permitted for re-identification; and (ii) The provider, PSO or responsible... identify the particular provider or reporter. (3) Re-identification. A provider, PSO, or responsible person... under this section to be re-identified by such provider, PSO, or responsible person, provided that: (i...

78 FR 23194 - Federal Acquisition Regulation; Commercial and Government Entity Code

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-18

... Award Management Name Change, Phase 1 Implementation) which will make a global update to all of the... outside the United States; and Support supply chain traceability and integrity efforts. II. Discussion and.... For Contractors registered in the System for Award Management (SAM), the DLA Logistics Information...

77 FR 60143 - Importer of Controlled Substances; Notice of Application; Fisher Clinical Services, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-02

... listed in schedules I or II, which fall under the authority of section 1002(a)(2)(B) of the Act [21 U.S.C... Diversion Control, Drug Enforcement Administration. [FR Doc. 2012-24191 Filed 10-1-12; 8:45 am] BILLING CODE...

Fermilab Today

Science.gov Websites

Seminar - Curia II Speaker: Chris Weaver, University of Wisconsin Title: Evidence for High-Energy up to the current code standards. The high-bay area (the space with the big crane), which will be away each year, and that's only the Styrofoam found in cups, not other packaging or food containers

42 CFR 489.20 - Basic commitments.

Code of Federal Regulations, 2011 CFR

2011-10-01

... section 1834(m)(4)(C)(ii)(VII) of the Act. (13) Those chemotherapy items identified, as of July 1, 1999... chemotherapy administration services identified, as of July 1, 1999, by HCPCS codes 36260-36262; 36489; 36530... this subchapter. The notice must indicate how the hospital will meet the medical needs of any patient...

38 CFR 41.105 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in section 551(1) of title 5, United States Code. Federal... programs are: (i) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other...

29 CFR 99.105 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in Section 551(1) of title 5, United States Code. Federal...) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other clusters” as described...

29 CFR 99.105 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in Section 551(1) of title 5, United States Code. Federal...) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other clusters” as described...

29 CFR 99.105 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in Section 551(1) of title 5, United States Code. Federal...) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other clusters” as described...

29 CFR 99.105 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in Section 551(1) of title 5, United States Code. Federal...) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other clusters” as described...

38 CFR 41.105 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in section 551(1) of title 5, United States Code. Federal... programs are: (i) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other...

29 CFR 99.105 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in Section 551(1) of title 5, United States Code. Federal...) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other clusters” as described...

38 CFR 41.105 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in section 551(1) of title 5, United States Code. Federal... programs are: (i) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other...

38 CFR 41.105 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in section 551(1) of title 5, United States Code. Federal... programs are: (i) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other...

38 CFR 41.105 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... share common compliance requirements. The types of clusters of programs are research and development (R... agency has the same meaning as the term agency in section 551(1) of title 5, United States Code. Federal... programs are: (i) Research and development (R&D); (ii) Student financial aid (SFA); and (iii) “Other...

9 CFR 307.7 - Safety requirements for electrical stimulating (EST) equipment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... beam sensors form the enclosure, the stimulating equipment shall be automatically shut off when the sensor signals are broken. (3) Mandatory Warning Devices and Signals. The following warning devices or.... (ii) An ANSI Z53.1-Color Code sign reading (a) “Danger Electrical Hazard” for stimulating voltage...

9 CFR 307.7 - Safety requirements for electrical stimulating (EST) equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... beam sensors form the enclosure, the stimulating equipment shall be automatically shut off when the sensor signals are broken. (3) Mandatory Warning Devices and Signals. The following warning devices or.... (ii) An ANSI Z53.1-Color Code sign reading (a) “Danger Electrical Hazard” for stimulating voltage...

50 CFR 17.41 - Special rules-birds.

Code of Federal Regulations, 2011 CFR

2011-10-01

...” (bred in captivity), or “D” (bred in captivity for commercial purposes)(see 50 CFR 23.24); or (ii... PLANTS (CONTINUED) ENDANGERED AND THREATENED WILDLIFE AND PLANTS Threatened Wildlife § 17.41 Special...: (i) Captive-bred specimens: The source code on the Convention on International Trade in Endangered...

50 CFR 17.41 - Special rules-birds.

Code of Federal Regulations, 2012 CFR

2012-10-01

...” (bred in captivity), or “D” (bred in captivity for commercial purposes)(see 50 CFR 23.24); or (ii... PLANTS (CONTINUED) ENDANGERED AND THREATENED WILDLIFE AND PLANTS Threatened Wildlife § 17.41 Special...: (i) Captive-bred specimens: The source code on the Convention on International Trade in Endangered...

32 CFR 757.13 - Responsibility for MCRA actions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Judge Advocate General (Claims and Tort Litigation Division) (Code 15); and the (ii) Commanding Officer, Naval Legal Service Command Europe and Southwest Asia (NLSC EURSWA), Naples, Italy, in its area of....S.C. 1095 claims are brought to the attention of the appropriate JAG designee. (2) The MTF reports...

40 CFR 65.13 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-07-01

... all are available for inspection or at the National Archives and Records Administration (NARA). For.../federal_register/code_of_federal_regulations/ibr_locations.html; at the Air and Radiation Docket and...)(3)(ii). (2) ASTM D2382-76, Standard Test Method for Heat of Combustion of Hydrocarbon Fuels by Bomb...

40 CFR 65.13 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-07-01

... all are available for inspection or at the National Archives and Records Administration (NARA). For.../federal_register/code_of_federal_regulations/ibr_locations.html; at the Air and Radiation Docket and...)(3)(ii). (2) ASTM D2382-76, Standard Test Method for Heat of Combustion of Hydrocarbon Fuels by Bomb...

System for the Analysis of Global Energy Markets - Vol. II, Model Documentation

EIA Publications

2003-01-01

The second volume provides a data implementation guide that lists all naming conventions and model constraints. In addition, Volume 1 has two appendixes that provide a schematic of the System for the Analysis of Global Energy Markets (SAGE) structure and a listing of the source code, respectively.

77 FR 43711 - The Commerce Control List

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-26

... DEPARTMENT OF COMMERCE Bureau of Industry and Security 15 CFR Part 774 The Commerce Control List CFR Correction In Title 15 of the Code of Federal Regulations, Parts 300 to 799, revised as of January... II, in 5E002, after ``Related Controls'' and before ``Items'', add ``Related Definitions: N/A''. [FR...

47 CFR 52.15 - Central office code administration.

Code of Federal Regulations, 2010 CFR

2010-10-01

... forecast data to the NANPA. (ii) Reporting shall be by separate legal entity and must include company name, company headquarters address, Operating Company Number (OCN), parent company OCN, and the primary type of... headquarters address, OCN, parent company's OCN(s), and the primary type of business in which the numbering...

40 CFR 370.43 - What codes are used to report Tier I and Tier II inventory information?

Code of Federal Regulations, 2010 CFR

2010-07-01

.... C Tank inside building. D Steel drum. E Plastic or non-metallic drum. F Can. G Carboy. H Silo. I Fiber drum. J Bag. K Box. L Cylinder. M Glass bottles or jugs. N Plastic bottles or jugs. O Tote bin. P...

78 FR 67020 - Airworthiness Directives; Eurocopter Deutschland GmbH (ECD) Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-08

... Airworthiness Directives; Eurocopter Deutschland GmbH (ECD) Helicopters AGENCY: Federal Aviation Administration... the AD Docket at http://www.regulations.gov . (h) Subject Joint Aircraft Service Component (JASC) Code..., of Eurocopter Deutschland GmbH Flight Manual BO 105 C/CS, Revision 5, dated March 12, 2010. (ii...

26 CFR 1.755-1 - Rules for allocation of basis.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CONTINUED) INCOME TAXES (CONTINUED) Provisions Common to Part II, Subchapter K, Chapter 1 of the Code § 1...) property (capital gain property), and any other property of the partnership (ordinary income property). For purposes of this section, properties and potential gain treated as unrealized receivables under section 751...

26 CFR 1.755-1 - Rules for allocation of basis.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) INCOME TAXES (CONTINUED) Provisions Common to Part II, Subchapter K, Chapter 1 of the Code § 1...) property (capital gain property), and any other property of the partnership (ordinary income property). For purposes of this section, properties and potential gain treated as unrealized receivables under section 751...

26 CFR 1.755-1 - Rules for allocation of basis.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) INCOME TAXES (CONTINUED) Provisions Common to Part II, Subchapter K, Chapter 1 of the Code § 1...) property (capital gain property), and any other property of the partnership (ordinary income property). For purposes of this section, properties and potential gain treated as unrealized receivables under section 751...

26 CFR 1.755-1 - Rules for allocation of basis.

Code of Federal Regulations, 2013 CFR

2013-04-01

... (CONTINUED) INCOME TAXES (CONTINUED) Provisions Common to Part II, Subchapter K, Chapter 1 of the Code § 1...) property (capital gain property), and any other property of the partnership (ordinary income property). For purposes of this section, properties and potential gain treated as unrealized receivables under section 751...

49 CFR 217.7 - Operating rules; filing and recordkeeping.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., Washington, DC 20590, one copy of its code of operating rules, timetables, and timetable special instructions which were in effect on November 21, 1994. Each Class I railroad, each Class II railroad, and each..., and timetable special instructions before it commences operations. (b) After November 21, 1994, each...

34 CFR 674.36 - Deferment of repayment-NDSLs made on or after October 1, 1980, but before July 1, 1993.

Code of Federal Regulations, 2010 CFR

2010-07-01

... section 501(c)(3) of the Internal Revenue Code of 1954. (ii) The borrower provides service to low-income... prescribed under section 6 of the Fair Labor Standards Act of 1938 (the Federal minimum wage), except that...

40 CFR 370.42 - What is Tier II inventory information?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Confidential and Non-Confidential Information Sheets and all attachments. All other pages must also contain..., the city, county, State and zip code. (d) The North American Industry Classification System (NAICS... “confidential.” You must provide the confidential location information on a separate sheet from the other Tier...

40 CFR 370.42 - What is Tier II inventory information?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Confidential and Non-Confidential Information Sheets and all attachments. All other pages must also contain..., the city, county, State and zip code. (d) The North American Industry Classification System (NAICS... “confidential.” You must provide the confidential location information on a separate sheet from the other Tier...

GAMSOR: Gamma Source Preparation and DIF3D Flux Solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, M. A.; Lee, C. H.; Hill, R. N.

2016-12-15

Nuclear reactors that rely upon the fission reaction have two modes of thermal energy deposition in the reactor system: neutron absorption and gamma absorption. The gamma rays are typically generated by neutron absorption reactions or during the fission process which means the primary driver of energy production is of course the neutron interaction. In conventional reactor physics methods, the gamma heating component is ignored such that the gamma absorption is forced to occur at the gamma emission site. For experimental reactor systems like EBR-II and FFTF, the placement of structural pins and assemblies internal to the core leads to problemsmore » with power heating predictions because there is no fission power source internal to the assembly to dictate a spatial distribution of the power. As part of the EBR-II support work in the 1980s, the GAMSOR code was developed to assist analysts in calculating the gamma heating. The GAMSOR code is a modified version of DIF3D and actually functions within a sequence of DIF3D calculations. The gamma flux in a conventional fission reactor system does not perturb the neutron flux and thus the gamma flux calculation can be cast as a fixed source problem given a solution to the steady state neutron flux equation. This leads to a sequence of DIF3D calculations, called the GAMSOR sequence, which involves solving the neutron flux, then the gamma flux, then combining the results to do a summary edit. In this manuscript, we go over the GAMSOR code and detail how it is put together and functions. We also discuss how to setup the GAMSOR sequence and input for each DIF3D calculation in the GAMSOR sequence. With the GAMSOR capability, users can take any valid steady state DIF3D calculation and compute the power distribution due to neutron and gamma heating. The MC2-3 code is the preferable companion code to use for generating neutron and gamma cross section data, but the GAMSOR code can accept cross section data from other sources. To further this aspect, an additional utility code was created which demonstrates how to merge the neutron and gamma cross section data together to carry out a simultaneous solve of the two systems.« less

The structural genes for three Drosophila glue proteins reside at a single polytene chromosome puff locus.

PubMed Central

Crowley, T E; Bond, M W; Meyerowitz, E M

1983-01-01

The polytene chromosome puff at 68C on the Drosophila melanogaster third chromosome is thought from genetic experiments to contain the structural gene for one of the secreted salivary gland glue polypeptides, sgs-3. Previous work has demonstrated that the DNA included in this puff contains sequences that are transcribed to give three different polyadenylated RNAs that are abundant in third-larval-instar salivary glands. These have been called the group II, group III, and group IV RNAs. In the experiments reported here, we used the nucleotide sequence of the DNA coding for these RNAs to predict some of the physical and chemical properties expected of their protein products, including molecular weight, amino acid composition, and amino acid sequence. Salivary gland polypeptides with molecular weights similar to those expected for the 68C RNA translation products, and with the expected degree of incorporation of different radioactive amino acids, were purified. These proteins were shown by amino acid sequencing to correspond to the protein products of the 68C RNAs. It was further shown that each of these proteins is a part of the secreted salivary gland glue: the group IV RNA codes for the previously described sgs-3, whereas the group II and III RNAs code for the newly identified glue polypeptides sgs-8 and sgs-7. Images PMID:6406838

Mediator directs co-transcriptional heterochromatin assembly by RNA interference-dependent and -independent pathways.

PubMed

Oya, Eriko; Kato, Hiroaki; Chikashige, Yuji; Tsutsumi, Chihiro; Hiraoka, Yasushi; Murakami, Yota

2013-01-01

Heterochromatin at the pericentromeric repeats in fission yeast is assembled and spread by an RNAi-dependent mechanism, which is coupled with the transcription of non-coding RNA from the repeats by RNA polymerase II. In addition, Rrp6, a component of the nuclear exosome, also contributes to heterochromatin assembly and is coupled with non-coding RNA transcription. The multi-subunit complex Mediator, which directs initiation of RNA polymerase II-dependent transcription, has recently been suggested to function after initiation in processes such as elongation of transcription and splicing. However, the role of Mediator in the regulation of chromatin structure is not well understood. We investigated the role of Mediator in pericentromeric heterochromatin formation and found that deletion of specific subunits of the head domain of Mediator compromised heterochromatin structure. The Mediator head domain was required for Rrp6-dependent heterochromatin nucleation at the pericentromere and for RNAi-dependent spreading of heterochromatin into the neighboring region. In the latter process, Mediator appeared to contribute to efficient processing of siRNA from transcribed non-coding RNA, which was required for efficient spreading of heterochromatin. Furthermore, the head domain directed efficient transcription in heterochromatin. These results reveal a pivotal role for Mediator in multiple steps of transcription-coupled formation of pericentromeric heterochromatin. This observation further extends the role of Mediator to co-transcriptional chromatin regulation.

Adaptive Core Simulation Employing Discrete Inverse Theory - Part II: Numerical Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdel-Khalik, Hany S.; Turinsky, Paul J.

2005-07-15

Use of adaptive simulation is intended to improve the fidelity and robustness of important core attribute predictions such as core power distribution, thermal margins, and core reactivity. Adaptive simulation utilizes a selected set of past and current reactor measurements of reactor observables, i.e., in-core instrumentation readings, to adapt the simulation in a meaningful way. The companion paper, ''Adaptive Core Simulation Employing Discrete Inverse Theory - Part I: Theory,'' describes in detail the theoretical background of the proposed adaptive techniques. This paper, Part II, demonstrates several computational experiments conducted to assess the fidelity and robustness of the proposed techniques. The intentmore » is to check the ability of the adapted core simulator model to predict future core observables that are not included in the adaption or core observables that are recorded at core conditions that differ from those at which adaption is completed. Also, this paper demonstrates successful utilization of an efficient sensitivity analysis approach to calculate the sensitivity information required to perform the adaption for millions of input core parameters. Finally, this paper illustrates a useful application for adaptive simulation - reducing the inconsistencies between two different core simulator code systems, where the multitudes of input data to one code are adjusted to enhance the agreement between both codes for important core attributes, i.e., core reactivity and power distribution. Also demonstrated is the robustness of such an application.« less

Distinct mutations in yeast TAF(II)25 differentially affect the composition of TFIID and SAGA complexes as well as global gene expression patterns.

PubMed

Kirschner, Doris B; vom Baur, Elmar; Thibault, Christelle; Sanders, Steven L; Gangloff, Yann-Gaël; Davidson, Irwin; Weil, P Anthony; Tora, Làszlò

2002-05-01

The RNA polymerase II transcription factor TFIID, composed of the TATA-binding protein (TBP) and TBP-associated factors (TAF(II)s), nucleates preinitiation complex formation at protein-coding gene promoters. SAGA, a second TAF(II)-containing multiprotein complex, is involved in transcription regulation in Saccharomyces cerevisiae. One of the essential protein components common to SAGA and TFIID is yTAF(II)25. We define a minimal evolutionarily conserved 91-amino-acid region of TAF(II)25 containing a histone fold domain that is necessary and sufficient for growth in vivo. Different temperature-sensitive mutations of yTAF(II)25 or chimeras with the human homologue TAF(II)30 arrested cell growth at either the G(1) or G(2)/M cell cycle phase and displayed distinct phenotypic changes and gene expression patterns. Immunoprecipitation studies revealed that TAF(II)25 mutation-dependent gene expression and phenotypic changes correlated at least partially with the integrity of SAGA and TFIID. Genome-wide expression analysis revealed that the five TAF(II)25 temperature-sensitive mutant alleles individually affect the expression of between 18 and 33% of genes, whereas taken together they affect 64% of all class II genes. Thus, different yTAF(II)25 mutations induce distinct phenotypes and affect the regulation of different subsets of genes, demonstrating that no individual TAF(II) mutant allele reflects the full range of its normal functions.

Summary Report of Working Group 2: Computation

NASA Astrophysics Data System (ADS)

Stoltz, P. H.; Tsung, R. S.

2009-01-01

The working group on computation addressed three physics areas: (i) plasma-based accelerators (laser-driven and beam-driven), (ii) high gradient structure-based accelerators, and (iii) electron beam sources and transport [1]. Highlights of the talks in these areas included new models of breakdown on the microscopic scale, new three-dimensional multipacting calculations with both finite difference and finite element codes, and detailed comparisons of new electron gun models with standard models such as PARMELA. The group also addressed two areas of advances in computation: (i) new algorithms, including simulation in a Lorentz-boosted frame that can reduce computation time orders of magnitude, and (ii) new hardware architectures, like graphics processing units and Cell processors that promise dramatic increases in computing power. Highlights of the talks in these areas included results from the first large-scale parallel finite element particle-in-cell code (PIC), many order-of-magnitude speedup of, and details of porting the VPIC code to the Roadrunner supercomputer. The working group featured two plenary talks, one by Brian Albright of Los Alamos National Laboratory on the performance of the VPIC code on the Roadrunner supercomputer, and one by David Bruhwiler of Tech-X Corporation on recent advances in computation for advanced accelerators. Highlights of the talk by Albright included the first one trillion particle simulations, a sustained performance of 0.3 petaflops, and an eight times speedup of science calculations, including back-scatter in laser-plasma interaction. Highlights of the talk by Bruhwiler included simulations of 10 GeV accelerator laser wakefield stages including external injection, new developments in electromagnetic simulations of electron guns using finite difference and finite element approaches.

Summary Report of Working Group 2: Computation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoltz, P. H.; Tsung, R. S.

2009-01-22

The working group on computation addressed three physics areas: (i) plasma-based accelerators (laser-driven and beam-driven), (ii) high gradient structure-based accelerators, and (iii) electron beam sources and transport [1]. Highlights of the talks in these areas included new models of breakdown on the microscopic scale, new three-dimensional multipacting calculations with both finite difference and finite element codes, and detailed comparisons of new electron gun models with standard models such as PARMELA. The group also addressed two areas of advances in computation: (i) new algorithms, including simulation in a Lorentz-boosted frame that can reduce computation time orders of magnitude, and (ii) newmore » hardware architectures, like graphics processing units and Cell processors that promise dramatic increases in computing power. Highlights of the talks in these areas included results from the first large-scale parallel finite element particle-in-cell code (PIC), many order-of-magnitude speedup of, and details of porting the VPIC code to the Roadrunner supercomputer. The working group featured two plenary talks, one by Brian Albright of Los Alamos National Laboratory on the performance of the VPIC code on the Roadrunner supercomputer, and one by David Bruhwiler of Tech-X Corporation on recent advances in computation for advanced accelerators. Highlights of the talk by Albright included the first one trillion particle simulations, a sustained performance of 0.3 petaflops, and an eight times speedup of science calculations, including back-scatter in laser-plasma interaction. Highlights of the talk by Bruhwiler included simulations of 10 GeV accelerator laser wakefield stages including external injection, new developments in electromagnetic simulations of electron guns using finite difference and finite element approaches.« less

Measuring affiliation in group therapy for substance use disorders in the Women's Recovery Group study: Does it matter whether the group is all-women or mixed-gender?

PubMed

Sugarman, Dawn E; Wigderson, Sara B; Iles, Brittany R; Kaufman, Julia S; Fitzmaurice, Garrett M; Hilario, E Yvette; Robbins, Michael S; Greenfield, Shelly F

2016-10-01

A Stage II, two-site randomized clinical trial compared the manualized, single-gender Women's Recovery Group (WRG) to mixed-gender group therapy (Group Drug Counseling; GDC) and demonstrated efficacy. Enhanced affiliation and support in the WRG is a hypothesized mechanism of efficacy. This study sought to extend results of the previous small Stage I trial that showed the rate of supportive affiliative statements occurred more frequently in WRG than GDC. Participants (N = 158; 100 women, 58 men) were 18 years or older, substance dependent, and had used substances within the past 60 days. Women were randomized to WRG (n = 52) or GDC (n = 48). Group therapy videos were coded by two independent raters; Rater 1 coded 20% of videos (n = 74); Rater 2 coded 25% of videos coded by Rater 1 (n = 19). The number of affiliative statements made in WRG was 66% higher than in GDC. Three of eight affiliative statement categories occurred more frequently in WRG than GDC: supportive, shared experience, and strategy statements. This larger Stage II trial provided a greater number of group therapy tapes available for analysis. Results extended our previous findings, demonstrating both greater frequency of all affiliative statements, as well as specific categories of statements, made in single-gender WRG than mixed-gender GDC. Greater frequency of affiliative statements among group members may be one mechanism of enhanced support and efficacy in women-only WRG compared with standard mixed-gender group therapy for substance use disorders. (Am J Addict 2016;25:573-580). © 2016 American Academy of Addiction Psychiatry.

A high burnup model developed for the DIONISIO code

NASA Astrophysics Data System (ADS)

Soba, A.; Denis, A.; Romero, L.; Villarino, E.; Sardella, F.

2013-02-01

A group of subroutines, designed to extend the application range of the fuel performance code DIONISIO to high burn up, has recently been included in the code. The new calculation tools, which are tuned for UO2 fuels in LWR conditions, predict the radial distribution of power density, burnup, and concentration of diverse nuclides within the pellet. The balance equations of all the isotopes involved in the fission process are solved in a simplified manner, and the one-group effective cross sections of all of them are obtained as functions of the radial position in the pellet, burnup, and enrichment in 235U. In this work, the subroutines are described and the results of the simulations performed with DIONISIO are presented. The good agreement with the data provided in the FUMEX II/III NEA data bank can be easily recognized.

Engine dynamic analysis with general nonlinear finite element codes. II - Bearing element implementation, overall numerical characteristics and benchmarking

NASA Technical Reports Server (NTRS)

Padovan, J.; Adams, M.; Lam, P.; Fertis, D.; Zeid, I.

1982-01-01

Second-year efforts within a three-year study to develop and extend finite element (FE) methodology to efficiently handle the transient/steady state response of rotor-bearing-stator structure associated with gas turbine engines are outlined. The two main areas aim at (1) implanting the squeeze film damper element into a general purpose FE code for testing and evaluation; and (2) determining the numerical characteristics of the FE-generated rotor-bearing-stator simulation scheme. The governing FE field equations are set out and the solution methodology is presented. The choice of ADINA as the general-purpose FE code is explained, and the numerical operational characteristics of the direct integration approach of FE-generated rotor-bearing-stator simulations is determined, including benchmarking, comparison of explicit vs. implicit methodologies of direct integration, and demonstration problems.

Implementation of context independent code on a new array processor: The Super-65

NASA Technical Reports Server (NTRS)

Colbert, R. O.; Bowhill, S. A.

1981-01-01

The feasibility of rewriting standard uniprocessor programs into code which contains no context-dependent branches is explored. Context independent code (CIC) would contain no branches that might require different processing elements to branch different ways. In order to investigate the possibilities and restrictions of CIC, several programs were recoded into CIC and a four-element array processor was built. This processor (the Super-65) consisted of three 6502 microprocessors and the Apple II microcomputer. The results obtained were somewhat dependent upon the specific architecture of the Super-65 but within bounds, the throughput of the array processor was found to increase linearly with the number of processing elements (PEs). The slope of throughput versus PEs is highly dependent on the program and varied from 0.33 to 1.00 for the sample programs.

HAlign-II: efficient ultra-large multiple sequence alignment and phylogenetic tree reconstruction with distributed and parallel computing.

PubMed

Wan, Shixiang; Zou, Quan

2017-01-01

Multiple sequence alignment (MSA) plays a key role in biological sequence analyses, especially in phylogenetic tree construction. Extreme increase in next-generation sequencing results in shortage of efficient ultra-large biological sequence alignment approaches for coping with different sequence types. Distributed and parallel computing represents a crucial technique for accelerating ultra-large (e.g. files more than 1 GB) sequence analyses. Based on HAlign and Spark distributed computing system, we implement a highly cost-efficient and time-efficient HAlign-II tool to address ultra-large multiple biological sequence alignment and phylogenetic tree construction. The experiments in the DNA and protein large scale data sets, which are more than 1GB files, showed that HAlign II could save time and space. It outperformed the current software tools. HAlign-II can efficiently carry out MSA and construct phylogenetic trees with ultra-large numbers of biological sequences. HAlign-II shows extremely high memory efficiency and scales well with increases in computing resource. THAlign-II provides a user-friendly web server based on our distributed computing infrastructure. HAlign-II with open-source codes and datasets was established at http://lab.malab.cn/soft/halign.

Efficient Simulation of Secondary Fluorescence Via NIST DTSA-II Monte Carlo.

PubMed

Ritchie, Nicholas W M

2017-06-01

Secondary fluorescence, the final term in the familiar matrix correction triumvirate Z·A·F, is the most challenging for Monte Carlo models to simulate. In fact, only two implementations of Monte Carlo models commonly used to simulate electron probe X-ray spectra can calculate secondary fluorescence-PENEPMA and NIST DTSA-II a (DTSA-II is discussed herein). These two models share many physical models but there are some important differences in the way each implements X-ray emission including secondary fluorescence. PENEPMA is based on PENELOPE, a general purpose software package for simulation of both relativistic and subrelativistic electron/positron interactions with matter. On the other hand, NIST DTSA-II was designed exclusively for simulation of X-ray spectra generated by subrelativistic electrons. NIST DTSA-II uses variance reduction techniques unsuited to general purpose code. These optimizations help NIST DTSA-II to be orders of magnitude more computationally efficient while retaining detector position sensitivity. Simulations execute in minutes rather than hours and can model differences that result from detector position. Both PENEPMA and NIST DTSA-II are capable of handling complex sample geometries and we will demonstrate that both are of similar accuracy when modeling experimental secondary fluorescence data from the literature.

Optimizing study design for interobserver reliability: IUGA-ICS classification of complications of prostheses and graft insertion.

PubMed

Haylen, Bernard T; Lee, Joseph; Maher, Chris; Deprest, Jan; Freeman, Robert

2014-06-01

Results of interobserver reliability studies for the International Urogynecological Association-International Continence Society (IUGA-ICS) Complication Classification coding can be greatly influenced by study design factors such as participant instruction, motivation, and test-question clarity. We attempted to optimize these factors. After a 15-min instructional lecture with eight clinical case examples (including images) and with classification/coding charts available, those clinicians attending an IUGA Surgical Complications workshop were presented with eight similar-style test cases over 10 min and asked to code them using the Category, Time and Site classification. Answers were compared to predetermined correct codes obtained by five instigators of the IUGA-ICS prostheses and grafts complications classification. Prelecture and postquiz participant confidence levels using a five-step Likert scale were assessed. Complete sets of answers to the questions (24 codings) were provided by 34 respondents, only three of whom reported prior use of the charts. Average score [n (%)] out of eight, as well as median score (range) for each coding category were: (i) Category: 7.3 (91 %); 7 (4-8); (ii) Time: 7.8 (98 %); 7 (6-8); (iii) Site: 7.2 (90 %); 7 (5-8). Overall, the equivalent calculations (out of 24) were 22.3 (93 %) and 22 (18-24). Mean prelecture confidence was 1.37 (out of 5), rising to 3.85 postquiz. Urogynecologists had the highest correlation with correct coding, followed closely by fellows and general gynecologists. Optimizing training and study design can lead to excellent results for interobserver reliability of the IUGA-ICS Complication Classification coding, with increased participant confidence in complication-coding ability.

A Comprehensive High Performance Predictive Tool for Fusion Liquid Metal Hydromagnetics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Peter; Chhabra, Rupanshi; Munipalli, Ramakanth

In Phase I SBIR project, HyPerComp and Texcel initiated the development of two induction-based MHD codes as a predictive tool for fusion hydro-magnetics. The newly-developed codes overcome the deficiency of other MHD codes based on the quasi static approximation by defining a more general mathematical model that utilizes the induced magnetic field rather than the electric potential as the main electromagnetic variable. The UCLA code is a finite-difference staggered-mesh code that serves as a supplementary tool to the massively-parallel finite-volume code developed by HyPerComp. As there is no suitable experimental data under blanket-relevant conditions for code validation, code-to-code comparisons andmore » comparisons against analytical solutions were successfully performed for three selected test cases: (1) lid-driven MHD flow, (2) flow in a rectangular duct in a transverse magnetic field, and (3) unsteady finite magnetic Reynolds number flow in a rectangular enclosure. The performed tests suggest that the developed codes are accurate and robust. Further work will focus on enhancing the code capabilities towards higher flow parameters and faster computations. At the conclusion of the current Phase-II Project we have completed the preliminary validation efforts in performing unsteady mixed-convection MHD flows (against limited data that is currently available in literature), and demonstrated flow behavior in large 3D channels including important geometrical features. Code enhancements such as periodic boundary conditions, unmatched mesh structures are also ready. As proposed, we have built upon these strengths and explored a much increased range of Grashof numbers and Hartmann numbers under various flow conditions, ranging from flows in a rectangular duct to prototypic blanket modules and liquid metal PFC. Parametric studies, numerical and physical model improvements to expand the scope of simulations, code demonstration, and continued validation activities have also been completed.« less

Genome-wide uniformity of human ‘open’ pre-initiation complexes

PubMed Central

Lai, William K.M.; Pugh, B. Franklin

2017-01-01

Transcription of protein-coding and noncoding DNA occurs pervasively throughout the mammalian genome. Their sites of initiation are generally inferred from transcript 5′ ends and are thought to be either locally dispersed or focused. How these two modes of initiation relate is unclear. Here, we apply permanganate treatment and chromatin immunoprecipitation (PIP-seq) of initiation factors to identify the precise location of melted DNA separately associated with the preinitiation complex (PIC) and the adjacent paused complex (PC). This approach revealed the two known modes of transcription initiation. However, in contrast to prevailing views, they co-occurred within the same promoter region: initiation originating from a focused PIC, and broad nucleosome-linked initiation. PIP-seq allowed transcriptional orientation of Pol II to be determined, which may be useful near promoters where sufficient sense/anti-sense transcript mapping information is lacking. PIP-seq detected divergently oriented Pol II at both coding and noncoding promoters, as well as at enhancers. Their occupancy levels were not necessarily coupled in the two orientations. DNA sequence and shape analysis of initiation complex sites suggest that both sequence and shape contribute to specificity, but in a context-restricted manner. That is, initiation sites have the locally “best” initiator (INR) sequence and/or shape. These findings reveal a common core to pervasive Pol II initiation throughout the human genome. PMID:27927716

Light Curves of the Type II-P Supernova SN 2017eaw: The First 200 Days

NASA Astrophysics Data System (ADS)

Tsvetkov, D. Yu.; Shugarov, S. Yu.; Volkov, I. M.; Pavlyuk, N. N.; Vozyakova, O. V.; Shatsky, N. I.; Nikiforova, A. A.; Troitsky, I. S.; Troitskaya, Yu. V.; Baklanov, P. V.

2018-05-01

We present the results of our UBVRI photometry for the type II-P supernova SN 2017eaw in NGC6946 obtained fromMay 14 to December 7, 2017, at several telescopes, including the 2.5-m telescope at the CaucasusHigh-Altitude Observatory of the SAIMSU. The dates andmagnitudes atmaximumlight and the light-curve parameters have been determined. The color evolution, extinction, and peak luminosity of SN 2017eaw are discussed. The results of our preliminary radiation-gasdynamic simulations of its light curves with the STELLA code describe satisfactorily the UBVRI observational data.

EBR-II and TREAT Digitization Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffith, George W.; Rabiti, Cristian

2015-09-01

Digitizing the technical drawings for EBR-II and TREAT provides multiple benefits. Moving the scanned or hard copy drawings to modern 3-D CAD (Computer Aided Drawing) format saves data that could be lost over time. The 3-D drawings produce models that can interface with other drawings to make complex assemblies. The 3-D CAD format can also include detailed material properties and parametric coding that can tie critical dimensions together allowing easier modification. Creating the new files from the old drawings has found multiple inconsistencies that are being flagged or corrected improving understanding of the reactor(s).

TFaNS Tone Fan Noise Design/Prediction System. Volume 3; Evaluation of System Codes

NASA Technical Reports Server (NTRS)

Topol, David A.

1999-01-01

TFANS is the Tone Fan Noise Design/Prediction System developed by Pratt & Whitney under contract to NASA Lewis (presently NASA Glenn). The purpose of this system is to predict tone noise emanating from a fan stage including the effects of reflection and transmission by the rotor and stator and by the duct inlet and nozzle. These effects have been added to an existing annular duct/isolated stator noise prediction capability. TFANS consists of: The codes that compute the acoustic properties (reflection and transmission coefficients) of the various elements and write them to files. Cup3D: Fan Noise Coupling Code that reads these files, solves the coupling problem, and outputs the desired noise predictions. AWAKEN: CFD/Measured Wake Postprocessor which reformats CFD wake predictions and/or measured wake data so it can be used by the system. This volume of the report evaluates TFANS versus full-scale and ADP 22" fig data using the semi-empirical wake modelling in the system. This report is divided into three volumes: Volume 1: System Description, CUP3D Technical Documentation, and Manual for Code Developers; Volume II: User's Manual, TFANS Version 1.4; Volume III: Evaluation of System Codes.

The primary transcriptome of the marine diazotroph Trichodesmium erythraeum IMS101

NASA Astrophysics Data System (ADS)

Pfreundt, Ulrike; Kopf, Matthias; Belkin, Natalia; Berman-Frank, Ilana; Hess, Wolfgang R.

2014-08-01

Blooms of the dinitrogen-fixing marine cyanobacterium Trichodesmium considerably contribute to new nitrogen inputs into tropical oceans. Intriguingly, only 60% of the Trichodesmium erythraeum IMS101 genome sequence codes for protein, compared with ~85% in other sequenced cyanobacterial genomes. The extensive non-coding genome fraction suggests space for an unusually high number of unidentified, potentially regulatory non-protein-coding RNAs (ncRNAs). To identify the transcribed fraction of the genome, here we present a genome-wide map of transcriptional start sites (TSS) at single nucleotide resolution, revealing the activity of 6,080 promoters. We demonstrate that T. erythraeum has the highest number of actively splicing group II introns and the highest percentage of TSS yielding ncRNAs of any bacterium examined to date. We identified a highly transcribed retroelement that serves as template repeat for the targeted mutation of at least 12 different genes by mutagenic homing. Our findings explain the non-coding portion of the T. erythraeum genome by the transcription of an unusually high number of non-coding transcripts in addition to the known high incidence of transposable elements. We conclude that riboregulation and RNA maturation-dependent processes constitute a major part of the Trichodesmium regulatory apparatus.

Criticality Calculations with MCNP6 - Practical Lectures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Forrest B.; Rising, Michael Evan; Alwin, Jennifer Louise

2016-11-29

These slides are used to teach MCNP (Monte Carlo N-Particle) usage to nuclear criticality safety analysts. The following are the lecture topics: course information, introduction, MCNP basics, criticality calculations, advanced geometry, tallies, adjoint-weighted tallies and sensitivities, physics and nuclear data, parameter studies, NCS validation I, NCS validation II, NCS validation III, case study 1 - solution tanks, case study 2 - fuel vault, case study 3 - B&W core, case study 4 - simple TRIGA, case study 5 - fissile mat. vault, criticality accident alarm systems. After completion of this course, you should be able to: Develop an input modelmore » for MCNP; Describe how cross section data impact Monte Carlo and deterministic codes; Describe the importance of validation of computer codes and how it is accomplished; Describe the methodology supporting Monte Carlo codes and deterministic codes; Describe pitfalls of Monte Carlo calculations; Discuss the strengths and weaknesses of Monte Carlo and Discrete Ordinants codes; The diffusion theory model is not strictly valid for treating fissile systems in which neutron absorption, voids, and/or material boundaries are present. In the context of these limitations, identify a fissile system for which a diffusion theory solution would be adequate.« less

An empirical analysis of journal policy effectiveness for computational reproducibility.

PubMed

Stodden, Victoria; Seiler, Jennifer; Ma, Zhaokun

2018-03-13

A key component of scientific communication is sufficient information for other researchers in the field to reproduce published findings. For computational and data-enabled research, this has often been interpreted to mean making available the raw data from which results were generated, the computer code that generated the findings, and any additional information needed such as workflows and input parameters. Many journals are revising author guidelines to include data and code availability. This work evaluates the effectiveness of journal policy that requires the data and code necessary for reproducibility be made available postpublication by the authors upon request. We assess the effectiveness of such a policy by ( i ) requesting data and code from authors and ( ii ) attempting replication of the published findings. We chose a random sample of 204 scientific papers published in the journal Science after the implementation of their policy in February 2011. We found that we were able to obtain artifacts from 44% of our sample and were able to reproduce the findings for 26%. We find this policy-author remission of data and code postpublication upon request-an improvement over no policy, but currently insufficient for reproducibility.

An empirical analysis of journal policy effectiveness for computational reproducibility

PubMed Central

Seiler, Jennifer; Ma, Zhaokun

2018-01-01

A key component of scientific communication is sufficient information for other researchers in the field to reproduce published findings. For computational and data-enabled research, this has often been interpreted to mean making available the raw data from which results were generated, the computer code that generated the findings, and any additional information needed such as workflows and input parameters. Many journals are revising author guidelines to include data and code availability. This work evaluates the effectiveness of journal policy that requires the data and code necessary for reproducibility be made available postpublication by the authors upon request. We assess the effectiveness of such a policy by (i) requesting data and code from authors and (ii) attempting replication of the published findings. We chose a random sample of 204 scientific papers published in the journal Science after the implementation of their policy in February 2011. We found that we were able to obtain artifacts from 44% of our sample and were able to reproduce the findings for 26%. We find this policy—author remission of data and code postpublication upon request—an improvement over no policy, but currently insufficient for reproducibility. PMID:29531050

42 CFR 483.470 - Condition of participation: Physical environment.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., comfortable, mattress; (iii) Bedding appropriate to the weather and climate; and (iv) Functional furniture... changes in this edition of the Code are incorporated by reference, CMS will publish notice in the Federal Register to announce the changes. (ii) Chapter 19.3.6.3.2, exception number 2 of the adopted LSC does not...

42 CFR 423.128 - Dissemination of Part D plan information.

Code of Federal Regulations, 2011 CFR

2011-10-01

... plan sponsor's toll free customer service line or by accessing the plan sponsor's internet Web site. (8... redetermination processes via an Internet Web site; and (iii) A system that transmits codes to network pharmacies...— (1) A toll-free customer call center that— (i) Is open during usual business hours. (ii) Provides...

75 FR 81120 - North Dakota Regulatory Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-27

... North Dakota's program and program amendments at 30 CFR 934.15, 934.16, and 934.30. II. Submission of... proposes revisions to the North Dakota Century Code at Chapter 38-14.1-24(18) (Environmental protection... applications--operation plans--maps and plans) and Article 69-05.2-22-07(2) and (4)(i) (Performance standards...

40 CFR 59.511 - What notifications and reports must I submit?

Code of Federal Regulations, 2011 CFR

2011-07-01

..., and the applicable reactivity factor; or (ii) For hydrocarbon solvent mixtures listed in either 2B or... reactivity factor. (10) For each product formulation, a list of the unique product codes by Universal Product... compounds listed in Table 2A of this subpart, the chemical name, CAS number, and the applicable reactivity...