Testing various modes of installation for permanent broadband stations in open field environment

NASA Astrophysics Data System (ADS)

Vergne, Jérôme; Charade, Olivier; Arnold, Benoît; Louis-Xavier, Thierry

2014-05-01

In the framework of the RESIF (Réseau Sismologique et géodésique Français) project, we plan to install more than one hundred new permanent broadband stations in metropolitan France within the next 6 years. Whenever possible, the sensors will be installed in natural or artificial underground cavities that provide a stable thermal environment. However such places do not exist everywhere and we expect that about half the future stations will have to be set up in open fields. For such sites, we are thus looking for a standard model of hosting infrastructure for the sensors that would be easily replicated and would provide good noise level performances at long periods. Since early 2013, we have been operating a prototype station at Clévilliers, a small location in the sedimentary Beauce plain, where we test three kinds of buried seismic vaults and a down-hole installation. The cylindrical seismic vaults are 3m deep and 1m wide and only differ by the type of coupling between the casing and the concrete slab where we installed insulated Trillium T120PA seismometers. The down-hole installation consists in a 3m deep well hosting a Trillium Posthole seismometer. For reference, another sensor has been installed in a ~50cm deep hole, similarly to the way we test every new potential site. Here we compare the noise level in each infrastructure at different frequencies. We observe quite similar performances for the vertical component recorded in the different wells. Conversely, the noise levels on the horizontal components at periods greater than 10s vary by more than 20dB depending on the installation condition. The best results are obtained in the completely decoupled vault and for the down-hole setting, both showing performances comparable to some of our permanent stations installed in tunnels. The amplitude of the horizontal noise also appears to be highly correlated to wind speed recorded on site, even at long periods. The variable response of each vault to such external forcing can partly explain the variations of the seismic noise levels.

Testing of Streckeisen STS-5A and Nanometrics Trillium 120PH Sensors for the Alaska Transportable Array

NASA Astrophysics Data System (ADS)

Abbasi Baghbadorani, A.; Aderhold, K.; Bloomquist, D.; Frassetto, A.; Miller, P. E.; Busby, R. W.

2017-12-01

Starting in 2014, the IRIS Transportable Array facility began to install and operate seismic stations in Alaska and western Canada. By the end of the project, the full deployment of the array will cover a grid of 280 stations spaced about 85 km apart covering all of mainland Alaska and parts of the Yukon, British Columbia, and the Northwest Territories. Approximately 200 stations will be operated directly by IRIS through at least 2019. A key aspect of the Alaska TA is the need for stations to operate autonomously, on account of the high cost of installation and potential subsequent visits to remote field-sites to repair equipment. The TA is using newly developed broadband seismometers Streckeisen STS-5A and Nanometrics Trillium-120PH, designed for installation in shallow posthole emplacements. These new instruments were extensively vetted beforehand, but they are still relatively new to the TA inventory. Here we will assess their performance under deployment conditions and after repeated commercial shipping and travel to the field. Our objective is to provide a thorough accounting of the identified failures of the existing inventory of posthole instruments. We will assess the practices and results of instrument testing by the PASSCAL Instrument Center/Array Operations Facility (PIC/AOF), Alaska Operations Center (AOC), and broadband seismic sensor manufacturers (Streckeisen, Nanometrics) in order to document potential factors in and stages during the process for instrument failures. This will help to quantify the overall reliability of the TA seismic sensors and quality of TA practices and data collection, and identify potential considerations in future TA operations. Our results show that the overall rate of failure of all posthole instruments is <4% out of 260. This is lower than the rates seen for vault sensor failures in the operation of the Lower 48 Transportable Array. For telemetered stations such as these installed in the TA Alaska array, we also show that noise analyses can capture a failed emplaced sensor and reveal improved station performance after sensor replacement, and that these are key elements in assessing whether or not a sensor should be replaced in the field.

Ghana's experience in the establishment of a national digital seismic network observatory

NASA Astrophysics Data System (ADS)

Ahulu, Sylvanus; Danuor, Sylvester Kojo

2015-07-01

The Government of Ghana has established a National Digital Seismic Network Observatory in Ghana with the aim of monitoring events such as earthquakes, blasts from mining and quarrying, nuclear tests, etc. The Digital Observatory was commissioned on 19 December 2012, and was dedicated to Geosciences in Ghana. Previously Ghana did not have any operational, digital seismic network acquisition system with the capability of monitoring and analysing data for planning and research purposes. The Ghana Geological Survey has been monitoring seismic events with an analogue system which was not efficient and does not deliver real-time data. Hence, the importance of setting up the National Digital Seismic Network System which would enable the Geological Survey to constantly monitor, manage and coordinate both natural and man-made seismic activities in the country and around the globe, to some extent on real-time basis. The Network System is made up of six remote digital stations that transmit data via satellite to the central observatory. Sensors used are 3× Trillium Compact and 3× Trillium 120PA with Trident digitizers. The department has also acquired strong motion equipment: Titan accelerometers with Taurus digitizers from Nanometrics. Three of each of these instruments have been installed at the Akosombo and Kpong hydrodams, and also at the Weija water supply dam. These instruments are used to monitor dams. The peak ground acceleration (PGA) values established from the analysed data from the accelerometers will be used to retrofit or carry out maintenance work of the dam structures to avoid collapse. Apart from these, the observatory also assesses and analyses seismic waveforms relevant to its needs from the Global Seismographic Network (GSN) system operated by the US Geological Survey. The Ghana Geological Survey, through its Seismic Network Observatory makes data available to its stakeholder institutions for earthquake disaster mitigation; reports on all aspects of seismic-related disasters to the relevant government agencies that deal with disasters; makes recommendations to the government of Ghana on earthquake safety measures; and provides information to assist government institutions develop appropriate land and building policies. The Geological Survey Department, in collaboration with stakeholder agencies, periodically organises public lectures on earthquake disaster risk mitigation.

Permafrost Active Layer Seismic Interferometry Experiment (PALSIE).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abbott, Robert; Knox, Hunter Anne; James, Stephanie

2016-01-01

We present findings from a novel field experiment conducted at Poker Flat Research Range in Fairbanks, Alaska that was designed to monitor changes in active layer thickness in real time. Results are derived primarily from seismic data streaming from seven Nanometric Trillium Posthole seismometers directly buried in the upper section of the permafrost. The data were evaluated using two analysis methods: Horizontal to Vertical Spectral Ratio (HVSR) and ambient noise seismic interferometry. Results from the HVSR conclusively illustrated the method's effectiveness at determining the active layer's thickness with a single station. Investigations with the multi-station method (ambient noise seismic interferometry)more » are continuing at the University of Florida and have not yet conclusively determined active layer thickness changes. Further work continues with the Bureau of Land Management (BLM) to determine if the ground based measurements can constrain satellite imagery, which provide measurements on a much larger spatial scale.« less

Helium-Based Soundwave Chiller: Trillium: A Helium-Based Sonic Chiller- Tons of Freezing with 0 GWP Refrigerants

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2010-09-01

BEETIT Project: Penn State is designing a freezer that substitutes the use of sound waves and environmentally benign refrigerant for synthetic refrigerants found in conventional freezers. Called a thermoacoustic chiller, the technology is based on the fact that the pressure oscillations in a sound wave result in temperature changes. Areas of higher pressure raise temperatures and areas of low pressure decrease temperatures. By carefully arranging a series of heat exchangers in a sound field, the chiller is able to isolate the hot and cold regions of the sound waves. Penn State’s chiller uses helium gas to replace synthetic refrigerants. Becausemore » helium does not burn, explode or combine with other chemicals, it is an environmentally-friendly alternative to other polluting refrigerants. Penn State is working to apply this technology on a large scale.« less

Effects of total saponins from Trillium tschonoskii rhizome on grey and white matter injury evaluated by quantitative multiparametric MRI in a rat model of ischemic stroke.

PubMed

Li, Manzhong; Ouyang, Junyao; Zhang, Yi; Cheng, Brian Chi Yan; Zhan, Yu; Yang, Le; Zou, Haiyan; Zhao, Hui

2018-04-06

Trillium tschonoskii rhizome (TTR), a medicinal herb, has been traditionally used to treat traumatic brain injury and headache in China. Although the potential neuroprotective efficacy of TTR has gained increasing interest, the pharmacological mechanism remains unclear. Steroid saponins are the main bioactive components of the herb. To investigate the protective and repair-promoting effects of the total saponins from TTR (TSTT) on grey and white matter damages in a rat model of middle cerebral artery occlusion (MCAO) using magnetic resonance imaging (MRI) assay. Ischemic stroke was induced by MCAO. TSTT and Ginaton (positive control) were administered orally to rats 6h after stroke and daily thereafter. After 15 days of treatment, the survival rate of each group was calculated. We then conducted neurological deficit scores and beam walking test to access the neurological function after ischemic stroke. Subsequently, T2-weighted imaging (T2WI) and T2 relaxometry mapping were performed to measure infarct volume and grey and white matter integrity, respectively. Moreover, diffusion tensor imaging (DTI) was carried out to evaluate the grey and white matter microstructural damage. Additionally, arterial spin labelling (ASL) - cerebral blood flow (CBF) and magnetic resonance angiography (MRA) images provided dynamic information about vascular hemodynamic dysfunction after ischemic stroke. Finally, haematoxylin and eosin (HE) staining was carried out to evaluate the stroke-induced pathological changes in the brain. The survival rate and neurological behavioural outcomes (Bederson scores and beam walking tests) were markedly ameliorated by TSTT (65mg/kg) treatment within 15 days after ischemic stroke. Moreover, T2WI and T2 relaxometry mapping showed that TSTT (65mg/kg) significantly reduced infarct volume and attenuated grey and white matter injury, respectively, which was confirmed by histopathological evaluation of brain tissue. The results obtained from DTI showed that TSTT (65mg/kg) not only significantly alleviated axonal damage and demyelination, but also promoted axonal remodelling and re-myelination. In addition, TSTT treatment also enhanced vascular signal density and increased CBF in rats after MCAO. Our results suggested the potential protective and repair-promoting effects of TSTT on grey and white matter from damage induced by ischemia. This study provides a modern pharmacological basis for the application of TSTT in managing ischemic stroke. Copyright © 2018 Elsevier B.V. All rights reserved.

Micro-seismic earthquakes characteristics at natural and exploited hydrothermal systems in West Java, Indonesia

NASA Astrophysics Data System (ADS)

Jousset, P. G.; Jaya, M. S.; Sule, R.; Diningrat, W.; Gassner, A.; Akbar, F.; Ryannugroho, R.; Hendryana, A.; Kusnadi, Y.; Syahbana, D.; Nugraha, A. D.; Umar, M.; Indrinanto, Y.; Erbas, K.

2013-12-01

The assessment of geothermal resources requires the understanding of the structure and the dynamics of geothermal reservoirs. We deployed a multidisciplinary geophysical network around geothermal areas in the south of Bandung, West Java, Indonesia. The first deployment included a network of 30 broadband and 4 short-period seismic stations with Güralp and Trillium sensors (0.008 - 100 Hz) since October 2012. In a second step, we extended the network in June 2013 with 16 short-period (1 Hz) seismometers. We describe the set-up of the seismic networks and discuss first observations and results. The co-existence of a large variety of intense surface manifestations like geysers, hot-steaming grounds, hot water pools, and active volcanoes suggest an intimate coupling between volcanic, tectonic and hydrothermal processes in this area. Preliminary location of earthquakes is performed using a non-linear algorithm, which allows us to define at least 3 seismic clusters. We discuss this seismic pattern within the geothermal fields.

Ant-seed mutualisms: Can red imported fire ants sour the relationship?

USGS Publications Warehouse

Zettler, J.A.; Spira, T.P.; Allen, Craig R.

2001-01-01

Invasion by the red imported fire ant, Solenopsis invicta, has had negative impacts on individual animal and plant species, but little is known about how S. invicta affects complex mutualistic relationships. In some eastern forests of North America, 30% of herbaceous species have ant-dispersed seeds. We conducted experiments to determine if fire ants are attracted to seeds of these plant species and assessed the amount of scarification or damage that results from handling by fire ants. Fire ants removed nearly 100% of seeds of the ant-dispersed plants Trillium undulatum, T. discolor, T. catesbaei, Viola rotundifolia, and Sanguinaria canadensis. In recovered seeds fed to ant colonies, fire ants scarified 80% of S. canadensis seeds and destroyed 86% of V. rotundifolia seeds. Our study is the first to document that red imported fire ants are attracted to and remove seeds of species adapted for ant dispersal. Moreover, fire ants might damage these seeds and discard them in sites unfavorable for germination and seedling establishment. ?? 2001 Elsevier Science Ltd. All rights reserved.

In Vitro Screening of Tumoricidal Properties of International Medicinal Herbs: Part II

PubMed Central

Mazzio, Elizabeth A.; Soliman, Karam F. A.

2010-01-01

With growing use of anticancer complementary and alternative medicines (CAMs) worldwide, there is a need to assess and screen commercially available natural products for relative tumoricidal properties under standard experimental conditions. In the current study, we screened and ranked 264 traditional Chinese and Egyptian herbal medicines for tumoricidal potency against malignant neuroblastoma in vitro. The data obtained show that tumoricidal potencies of plants were randomly dispersed throughout similar orders, families and genera under the Division: Magnoliophyta, class: Magnoliopsida, subclasses: Asteridae, Caryophyllidae, Dilleniidae, Hamamelididae, Magnoliidae and Rosidae. The most potent plant extracts (LC50 < 0.08 mg/ml) were prepared from gromwell root also known as ‘Hong Tiao Zi Cao’ (Lithospermum Erythrorhizon) Family (Boraginaceae) > beth root (Trillium Pendulum), Family (Liliaceae) and galbanum (Ferula Galbaniflua), Family (Apiaceae). Gromwell root is traditionally used in the preparation of Chinese medicinal tea. In addition, galbanum was highly regarded for its sacred and medicinal value according to ancient texts and the bible. Future research will be required to isolate and identify chemical constituents within these plants which are responsible for tumoricidal effects. PMID:20564497

Transport of Intrinsic Plutonium Colloids in Saturated Porous Media

NASA Astrophysics Data System (ADS)

Zhou, D.; Abdel-Fattah, A.; Boukhalfa, H.; Ware, S. D.; Tarimala, S.; Keller, A. A.

2011-12-01

Actinide contaminants were introduced to the subsurface environment as a result of nuclear weapons development and testing, as well as for nuclear power generation and related research activities for defense and civilian applications. Even though most actinide species were believed to be fairly immobile once in the subsurface, recent studies have shown the transport of actinides kilometers away from their disposal sites. For example, the treated liquid wastes released into Mortandad Canyon at the Los Alamos National Laboratory were predicted to travel less than a few meters; however, plutonium and americium have been detected 3.4 km away from the waste outfall. A colloid-facilitated mechanism has been suggested to account for this unexpected transport of these radioactive wastes. Clays, oxides, organic matters, and actinide hydroxides have all been proposed as the possible mobile phase. Pu ions associated with natural colloids are often referred to as pseudo-Pu colloids, in contrast with the intrinsic Pu colloids that consist of Pu oxides. Significant efforts have been made to investigate the role of pseudo-Pu colloids, while few studies have evaluated the environmental behavior of the intrinsic Pu colloids. Given the fact that Pu (IV) has extremely low solubility product constant, it can be inferred that the transport of Pu in the intrinsic form is highly likely at suitable environmental conditions. This study investigates the transport of intrinsic Pu colloids in a saturated alluvium material packed in a cylindrical column (2.5-cm Dia. x 30-cm high) and compares the results to previous data on the transport of pseudo Pu colloids in the same material. A procedure to prepare a stable intrinsic Pu colloid suspension that produced consistent and reproducible electrokinetic and stability data was developed. Electrokinetic properties and aggregation stability were characterized. The Pu colloids, together with trillium as a conservative tracer, were injected into the column at a flow rate of ~ 6 mL/hr. Despite that the Pu intrinsic colloids are positively charged while the alluvium grain surfaces are negatively charged under the current experimental conditions, about 30% of the Pu colloids population transported through the column and broke through earlier than trillium. Our previous experiments in the same column have shown a highly unretarded transport of the negatively charged pseudo Pu colloids (Pu sorbed onto smectite colloids) and complete retardation of the dissolved Pu. The enhanced transport of Pu colloids was explained by the effective pore volume concept. Combining the results of these two experiments, it is concluded that the intrinsic Pu colloids transported in the column by adsorbing onto the background clay colloids due to electrostatic repulsion.

Leadership profile: HealthAchieve 2013 Nursing Leadership Award Winner, Tiziana Rivera.

PubMed

Rivera, Tiziana

2014-03-01

Tiziana Rivera, the winner of the 2013 Nursing Leadership Award at the November HealthAchieve conference, is chief nursing executive and chief practice officer at Mackenzie Health. As such, she provides strategic leadership for the development and implementation of a shared vision for professional practice, nursing and all disciplines to promote innovative care and the development of care delivery models that will improve quality of care and population health.Prior to assuming her position at Mackenzie Health, Rivera provided strategic leadership for the Seniors' Health Program at Trillium Health Centre, where her role focused on the development of seniors' health services across the continuum of care. She has published numerous articles in refereed journals, conducted several research studies and presented her papers provincially, nationally and internationally. Rivera has a clinical appointment at the University of Toronto Faculty of Nursing, a faculty adviser position at Ryerson and an adjunct faculty position at the School of Health Sciences, York University and at the School of Health Sciences, Humber Institute of Technology and Advanced Learning.In the following Q and A, Rivera shares her thoughts on leadership in nursing and perspectives on several critical issues.

Evolution in Stage-Structured Populations

PubMed Central

Barfield, Michael; Holt, Robert D.; Gomulkiewicz, Richard

2016-01-01

For many organisms, stage is a better predictor of demographic rates than age. Yet no general theoretical framework exists for understanding or predicting evolution in stage-structured populations. Here, we provide a general modeling approach that can be used to predict evolution and demography of stage-structured populations. This advances our ability to understand evolution in stage-structured populations to a level previously available only for populations structured by age. We use this framework to provide the first rigorous proof that Lande’s theorem, which relates adaptive evolution to population growth, applies to stage-classified populations, assuming only normality and that evolution is slow relative to population dynamics. We extend this theorem to allow for different means or variances among stages. Our next major result is the formulation of Price’s theorem, a fundamental law of evolution, for stage-structured populations. In addition, we use data from Trillium grandiflorum to demonstrate how our models can be applied to a real-world population and thereby show their practical potential to generate accurate projections of evolutionary and population dynamics. Finally, we use our framework to compare rates of evolution in age- versus stage-structured populations, which shows how our methods can yield biological insights about evolution in stage-structured populations. PMID:21460563

Repeatability of testing a small broadband sensor in the Albuquerque Seismological Laboratory Underground Vault

USGS Publications Warehouse

Ringler, Adam; Holland, Austin; Wilson, David

2017-01-01

Variability in seismic instrumentation performance plays a fundamental role in our ability to carry out experiments in observational seismology. Many such experiments rely on the assumed performance of various seismic sensors as well as on methods to isolate the sensors from nonseismic noise sources. We look at the repeatability of estimating the self‐noise, midband sensitivity, and the relative orientation by comparing three collocated Nanometrics Trillium Compact sensors. To estimate the repeatability, we conduct a total of 15 trials in which one sensor is repeatedly reinstalled, alongside two undisturbed sensors. We find that we are able to estimate the midband sensitivity with an error of no greater than 0.04% with a 99th percentile confidence, assuming a standard normal distribution. We also find that we are able to estimate mean sensor self‐noise to within ±5.6  dB with a 99th percentile confidence in the 30–100‐s‐period band. Finally, we find our relative orientation errors have a mean difference in orientation of 0.0171° from the reference, but our trials have a standard deviation of 0.78°.

First Observations with the New Dual Sphere Superconducting Gravimeter Osg-073 at Metsähovi, Finland

NASA Astrophysics Data System (ADS)

Virtanen, H.; Raja-Halli, A.; Bilker-Koivula, M.; Naranen, J.; Ruotsalainen, H. E. O.

2014-12-01

The new dual sphere superconducting gravimeter (SG) OSG-073 was installed in the Metsähovi Geodetic Observatory in February 2014. Its two gravity sensors are side by side, not one on top of another as in most earlier dual sensor installations. One sensor is the standard iGrav™ SG, with a lightweight sphere (5 grams) which is nearly drift-free. The second sensor uses a heavy 20-gram sphere which gives ultra low noise and a much higher quality factor Q. We present time domain observations of the first months, and estimate drift rates after the initial exponential drift. We have determined the transfer functions. Calibration factors were obtained using parallel registrations with the FG5X-221 absolute gravimeter of the FGI. We show selected free oscillation spectra from the SG, and seismic data obtained at Metsähovi with the Nanometrics Trillium 120P broadband seismometer of the Institute of Seismology (University of Helsinki). The noise level of the data is then compared with the New Low Noise Model NLNM. The results with the dual sphere SG can be compared with parallel observations with the SG T020. This 20-year old instrument is situated in the same room at a distance of 2 metres from the dual-sphere SG.

Improvements in absolute seismometer sensitivity calibration using local earth gravity measurements

USGS Publications Warehouse

Anthony, Robert E.; Ringler, Adam; Wilson, David

2018-01-01

The ability to determine both absolute and relative seismic amplitudes is fundamentally limited by the accuracy and precision with which scientists are able to calibrate seismometer sensitivities and characterize their response. Currently, across the Global Seismic Network (GSN), errors in midband sensitivity exceed 3% at the 95% confidence interval and are the least‐constrained response parameter in seismic recording systems. We explore a new methodology utilizing precise absolute Earth gravity measurements to determine the midband sensitivity of seismic instruments. We first determine the absolute sensitivity of Kinemetrics EpiSensor accelerometers to 0.06% at the 99% confidence interval by inverting them in a known gravity field at the Albuquerque Seismological Laboratory (ASL). After the accelerometer is calibrated, we install it in its normal configuration next to broadband seismometers and subject the sensors to identical ground motions to perform relative calibrations of the broadband sensors. Using this technique, we are able to determine the absolute midband sensitivity of the vertical components of Nanometrics Trillium Compact seismometers to within 0.11% and Streckeisen STS‐2 seismometers to within 0.14% at the 99% confidence interval. The technique enables absolute calibrations from first principles that are traceable to National Institute of Standards and Technology (NIST) measurements while providing nearly an order of magnitude more precision than step‐table calibrations.

The GINGERino ring laser gyroscope, seismological observations at one year from the first light

NASA Astrophysics Data System (ADS)

Simonelli, Andreino; Belfi, Jacopo; Beverini, Nicolò; Di Virgilio, Angela; Carelli, Giorgio; Maccioni, Enrico; De Luca, Gaetano; Saccorotti, Gilberto

2016-04-01

The GINGERino ring laser gyroscope (RLG) is a new large observatory-class RLG located in Gran Sasso underground laboratory (LNGS), one national laboratory of the INFN (Istituto Nazionale di Fisica Nucleare). The GINGERino apparatus funded by INFN in the context of a larger project of fundamental physics is intended as a pathfinder instrument to reach the high sensitivity needed to observe general relativity effects; more details are found at the URL (https://web2.infn.it/GINGER/index.php/it/). The sensitivity reached by our instrument in the first year after the set up permitted us to acquire important seismological data of ground rotations during the transit of seismic waves generated by seisms at different epicentral distances. RLGs are in fact the best sensors for capturing the rotational motions associated with the transit of seismic waves, thanks to the optical measurement principle, these instruments are in fact insensitive to translations. Ground translations are recorded by two seismometers: a Nanometrics Trillium 240 s and Guralp CMG 3T 360 s, the first instrument is part of the national earthquake monitoring program of the Istituto Nazionale di Geofisica e Vulcanologia (INGV) and provides the ground translation data to be compared to the RLG rotational data. We report the waveforms and the seismological analysis of some seismic events recorded during our first year of activity inside the LNGS laboratory.

Identical Aftershocks from the Main Rupture Zone 10 Months After the Mw=7.6 September 5, 2012, Nicoya, Costa Rica, Earthquake

NASA Astrophysics Data System (ADS)

Protti, M.; Alfaro-Diaz, R.; Brenn, G. R.; Fasola, S.; Murillo, A.; Marshall, J. S.; Gardner, T. W.

2013-12-01

Over a two weeks period and as part of a Keck Geology Consortium summer research project, we installed a dense broad band seismic array directly over the rupture zone of the Nicoya, September 5th, 2012, Mw=7.6 earthquake. The network consisted of 5 Trillium compact seismometers and Taurus digitizers from Nanometrics, defining a triangular area of ~20 km per side. Also located within this area are 3 stations of the Nicoya permanent broadband network. One side of the triangular area, along the west coast of the Nicoya peninsula, is parallel to the trench and the apex lies 15 km landward. The plate interface and rupture zone of the Nicoya 2012 earthquake are located 16 km below the trench-parallel side and 25 km below the apex of this triangular footprint. Station spacing ranged from 3 to 14 km. This dense array operated from July 2nd to July 17th, 2013. On June 23rd, eight days before we installed this array, an Mw=5.4 aftershock (one of the only 5 aftershocks of the Nicoya Mw=7.6 earthquake with magnitudes above 5.0) occurred directly beneath the area of our temporary network. Preliminary analysis of the data shows that we recorded several identical aftershocks with magnitudes below 1.0 that locate some 18 km below our network. We will present detailed locations of these small aftershocks and their relationship with the June 23rd, 2013 aftershock and the September 5th, 2012, mainshock.

New Observations of Seismic Group Velocities in the Western Solomon Islands from Cross-Correlation of Ambient Seismic Noise

NASA Astrophysics Data System (ADS)

Ku, C. S.; You, S. H.; Kuo, Y. T.; Huang, B. S.; Wu, Y. M.; Chen, Y. G.; Taylor, F. W.

2015-12-01

A MW 8.1 earthquake occurred on 1 April 2007 in the western Solomon Islands. Following this event, a damaging tsunami was induced and hit the Island Gizo where the capital city of Western Province of Solomon Islands located. Several buildings of this city were destroyed and several peoples lost their lives during this earthquake. However, during this earthquake, no near source seismic instrument has been installed in this region. The seismic evaluations for the aftershock sequence, the possible earthquake early warning and tsunami warning were unavailable. For the purpose of knowing more detailed information about seismic activity in this region, we have installed 9 seismic stations (with Trillium 120PA broadband seismometer and Q330S 24bit digitizer) around the rupture zone of the 2007 earthquake since September of 2009. Within a decade, it has been demonstrated both theoretically and experimentally that the Green's function or impulse response between two seismic stations can be retrieved from the cross-correlation of ambient noise. In this study, 6 stations' observations which are more complete during 2011/10 ~ 2012/12 period, were selected for the purpose of the cross-correlation analysis of ambient seismic noise. The group velocities at period 2-20 seconds of 15 station-pairs were extracted by using multiple filter technique (MFT) method. The analyzed results of this study presented significant results of group velocities with higher frequency contents than other studies (20-60 seconds in usually cases) and opened new opportunities to study the shallow crustal structure of the western Solomon Islands.

Preference-based disease-specific health-related quality of life instrument for glaucoma: a mixed methods study protocol

PubMed Central

Muratov, Sergei; Podbielski, Dominik W; Jack, Susan M; Ahmed, Iqbal Ike K; Mitchell, Levine A H; Baltaziak, Monika; Xie, Feng

2016-01-01

Introduction A primary objective of healthcare services is to improve patients' health and health-related quality of life (HRQoL). Glaucoma, which affects a substantial proportion of the world population, has a significant detrimental impact on HRQoL. Although there are a number of glaucoma-specific questionnaires to measure HRQoL, none is preference-based which prevent them from being used in health economic evaluation. The proposed study is aimed to develop a preference-based instrument that is capable of capturing important effects specific to glaucoma and treatments on HRQoL and is scored based on the patients' preferences. Methods A sequential, exploratory mixed methods design will be used to guide the development and evaluation of the HRQoL instrument. The study consists of several stages to be implemented sequentially: item identification, item selection, validation and valuation. The instrument items will be identified and selected through a literature review and the conduct of a qualitative study. Validation will be conducted to establish psychometric properties of the instrument followed by a valuation exercise to derive utility scores for the health states described. Ethics and dissemination This study has been approved by the Trillium Health Partners Research Ethics Board (ID number 753). All personal information will be de-identified with the identification code kept in a secured location including the rest of the study data. Only qualified and study-related personnel will be allowed to access the data. The results of the study will be distributed widely through peer-reviewed journals, conferences and internal meetings. PMID:28186941

Using Co-located Rotational and Translational Ground-Motion Sensors to Characterize Seismic Scattering in the P-Wave Coda

NASA Astrophysics Data System (ADS)

Bartrand, J.; Abbott, R. E.

2017-12-01

We present data and analysis of a seismic data collect at the site of a historical underground nuclear explosion at Yucca Flat, a sedimentary basin on the Nevada National Security Site, USA. The data presented here consist of active-source, six degree-of-freedom seismic signals. The translational signals were collected with a Nanometrics Trillium Compact Posthole seismometer and the rotational signals were collected with an ATA Proto-SMHD, a prototype rotational ground motion sensor. The source for the experiment was the Seismic Hammer (a 13,000 kg weight-drop), deployed on two-kilometer, orthogonal arms centered on the site of the nuclear explosion. By leveraging the fact that compressional waves have no rotational component, we generated a map of subsurface scattering and compared the results to known subsurface features. To determine scattering intensity, signals were cut to include only the P-wave and its coda. The ratio of the time-domain signal magnitudes of angular velocity and translational acceleration were sectioned into three time windows within the coda and averaged within each window. Preliminary results indicate an increased rotation/translation ratio in the vicinity of the explosion-generated chimney, suggesting mode conversion of P-wave energy to S-wave energy at that location. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International Inc. for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.

High throughput screening of natural products for anti-mitotic effects in MDA-MB-231 human breast carcinoma cells

PubMed Central

Mazzio, E; Badisa, R; Mack, N; Deiab, S; Soliman, KFA

2013-01-01

Some of the most effective anti-mitotic microtubule-binding agents, such as paclitaxel (Taxus brevifolia) were originally discovered through robust NCI botanical screenings. In this study, a high-through microarray format was utilized to screen 897 aqueous extracts of commonly used natural products (0.00015–0.5 mg/ml) relative to paclitaxel for anti-mitotic effects (independent of toxicity) on proliferation of MDA-MB-231 cells. The data obtained showed that less than 1.34 % tested showed inhibitory growth (IG50) properties <0.0183 mg/ml. The most potent anti-mitotics (independent of toxicity) were Mandrake root (Podophyllum peltatum), Truja Twigs (Thuja occidentalis), Colorado desert mistletoe (Phoradendron flavescens), Tou Gu Cao Speranskia Herb (Speranskia tuberculata), Bentonite Clay, Bunge Root (Pulsatilla chinensis), Brucea Fruit (Brucea javanica), Madder Root (Rubia tinctorum), Gallnut of Chinese Sumac (Melaphis chinensis), Elecampane Root (Inula Helenium), Yuan Zhi Root (Polygala tenuifolia), Pagoda Tree Fruit (Melia Toosendan), Stone Root (Collinsonia Canadensis) and others such as American Witchhazel, Arjun and Bladderwrack. The strongest tumoricidal herbs identified from amongst the subset evaluated for anti-mitotic properties were wild yam (Dioscorea villosa), beth-root (Trillium Pendulum) and alkanet-root (Lithospermum canescens). Additional data was obtained on a lesser-recognized herb: (Speranskia tuberculata) which showed growth inhibition on BT-474 (human ductal breast carcinoma) and Ishikawa (human endometrial adenocarcinoma) cells with ability to block replicative DNA synthesis leading to G2 arrest in MDA-MB-231 cells. In conclusion, these findings present relative potency of natural anti-mitotic resources effective against human breast carcinoma MDA-MB-231 cell division. PMID:24105850

Oxygenator Safety Evaluation: A Focus on Connection Grip Strength and Arterial Temperature Measurement Accuracy

PubMed Central

Newland, Richard F.; Baker, Robert A.; Sanderson, Andrew J.; Tuble, Sigrid C.; Tully, Phil J.

2012-01-01

Abstract: This report describes the assessment of three specific safety-related specifications in the consideration of an alternate oxygenator; first the grip strength relationship between various oxygenator connectors and SMARxT® tubing, second, the grip strength of various biopassive tubings and an isolated SMARxT® connector, and finally, the accuracy of the arterial outlet temperature measurement. Grip strength experiments for the connections between the SMARxT® tubing and the venous reservoir outlet and the oxygenator venous inlet and oxygenator arterial outlet of the Medtronic Affinity®, Sorin Synthesis®, Sorin Primox®, and Terumo Capiox® RX25 oxygenators were performed. In addition we compared the grip strength of polyvinyl chloride, Physio®, Trillium®, Carmeda®, X-Coating®, and SMARxT® tubing. The accuracy of the integrated arterial outlet temperature probes was determined by comparing the temperatures measured by the integrated probe with a precision reference thermometer. Connector grip strength comparisons for the evaluation oxygenators with SMARxT® tubing showed significant variation between oxygenators and connections (p = .02). Evaluation of the arterial outlet showed significant variation between evaluation oxygenators, while at the venous reservoir outlet and oxygenator inlet, there were no significant differences. Grip strength comparison data for the various tubing types demonstrated a main effect for tubing type F(5, 18) = 8.01, p = .002, ηp2 = .77. Temperature accuracy measurements demonstrated that all oxygenators overread the arterial outlet temperature at 15°C, whilst at temperatures ≥25°C, all oxygenators underread the arterial outlet temperature. The integrity of SMARxT® tubing connection is influenced by the connector type, and may decline over time, highlighting the importance to not consider interchanging components of the bypass circuit as inconsequential. PMID:22893983

Passive seismic experiment in the Olduvai Gorge and Laetoli region (Ngorongoro Conservation Area), Northern Tanzania.

NASA Astrophysics Data System (ADS)

Parisi, Laura; Lombardo, Luigi; Tang, Zheng; Mai, P. Martin

2017-04-01

The Olduvai Gorge and Laetoli basins, located within the Ngorogoro Conservation Area (NCA), are a cornerstone for understanding the evolution of early humans and are two paleo-antropological excavation sites of global importance. NCA is located at the boundary between the Tanzanian Craton and East African Rift (EAR), in the vicinity of Ngorongoro Crater and other major volcanic edifices. Thus, understanding the geology and tectonics of the NCA may shed light onto the question why early Hominins settled in this region. Environmental and geological conditions in the Olduvai and Laetoli region that promoted human settlement and development are still debated by geologists and paleo-anthropologists. Paleo-geographical reconstructions of the study area of the last 2 million years may take advantage of modern passive seismology. Therefore, we installed a dense seismic network covering a surface of approximately 30 x 40 km within the NCA to map the depth extent of known faults, and to identify seismically active faults that have no surface expression. Our ten seismic stations, equipped with Trillium Compact 120 s sensors, started to operate in June 2016 and will continue for a total of 2 years. At the end of the first year, other 5 stations will densify our network. Here we analyse data quality of the first four months of continuous recordings. Our network provides good quality 3-C waveforms in the frequency range of 0.7-50 Hz. Vertical component seismograms record frequencies reliably down to 8 mHz. Preliminary results of the seismicity obtained with standard location procedures show that NCA is characterised by frequent tectonic seismicity (not volcano-related) with Ml between 0.5 and 2.0. Seismic activity is more frequent in the South (Laetoli region) where major fault systems have not been recognised at the surface yet.

Recent Instrumentation Developments in the Global Seismographic Network (GSN)

NASA Astrophysics Data System (ADS)

Hafner, K.; Davis, J. P.; Wilson, D.

2016-12-01

One of the challenges facing the GSN is continuing to provide robust, uniform high-quality, very broadband, high-dynamic range recordings of ground motion data as the original primary seismometers age. Recently the GSN has been upgrading all stations with the next generation of digital data acquisition systems (DASs), which has significantly increased the station data availability. In 2012, the Department of Energy received an additional $5.7M to support GSN refurbishment. The funds were transferred to the USGS via a 5-year interagency agreement and have been used for developing the next generation of very broadband (VBB) sensors. The USGS Albuquerque Seismic Laboratory (ASL) received the first prototype of a very broadband borehole sensor (Streckeisen STS-6A) in November 2015. Initial testing showed this prototype met all the required sensor specifications. Three pre-production sensors are scheduled to arrive by late August 2016. We will present the results of testing these devices, as well as an update on other recent VBB sensor developments (Trillium T360) and how they compare to the performance of the STS-1 and other available sensors. Recent work at ASL and the USArray Transportable Array has shown that installing sensors in shallow postholes up to 10 meters deep can lead to significant improvement in data quality. The GSN is investigating the potential of installing borehole sensors at some GSN stations where the STS-1 has shown significant susceptibility to pier tilt, temperature instability, or cultural noise. The GSN is also broadening the types of sensors deployed at GSN stations. After initial testing at ASL and UCSD's Pinyon Flat test site, the first infrasound sensor deployment will take place in Fall 2016. We will present the results of these tests and descriptions of the initial deployment.

Preference-based disease-specific health-related quality of life instrument for glaucoma: a mixed methods study protocol.

PubMed

Muratov, Sergei; Podbielski, Dominik W; Jack, Susan M; Ahmed, Iqbal Ike K; Mitchell, Levine A H; Baltaziak, Monika; Xie, Feng

2016-11-08

A primary objective of healthcare services is to improve patients' health and health-related quality of life (HRQoL). Glaucoma, which affects a substantial proportion of the world population, has a significant detrimental impact on HRQoL. Although there are a number of glaucoma-specific questionnaires to measure HRQoL, none is preference-based which prevent them from being used in health economic evaluation. The proposed study is aimed to develop a preference-based instrument that is capable of capturing important effects specific to glaucoma and treatments on HRQoL and is scored based on the patients' preferences. A sequential, exploratory mixed methods design will be used to guide the development and evaluation of the HRQoL instrument. The study consists of several stages to be implemented sequentially: item identification, item selection, validation and valuation. The instrument items will be identified and selected through a literature review and the conduct of a qualitative study. Validation will be conducted to establish psychometric properties of the instrument followed by a valuation exercise to derive utility scores for the health states described. This study has been approved by the Trillium Health Partners Research Ethics Board (ID number 753). All personal information will be de-identified with the identification code kept in a secured location including the rest of the study data. Only qualified and study-related personnel will be allowed to access the data. The results of the study will be distributed widely through peer-reviewed journals, conferences and internal meetings. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Shear-wave velocities beneath the Harrat Rahat volcanic field, Saudi Arabia, using ambient seismic noise analysis

NASA Astrophysics Data System (ADS)

Civilini, F.; Mooney, W.; Savage, M. K.; Townend, J.; Zahran, H. M.

2017-12-01

We present seismic shear-velocities for Harrat Rahat, a Cenozoic bimodal alkaline volcanic field in west-central Saudi Arabia, using seismic tomography from natural ambient noise. This project is part of an overall effort by the Saudi Geological Survey and the United States Geological Survey to describe the subsurface structure and assess hazards within the Saudi Arabian shield. Volcanism at Harrat Rahat began approximately 10 Ma, with at least three pulses around 10, 5, and 2 Ma, and at least several pulses in the Quaternary from 1.9 Ma to the present. This area is instrumented by 14 broadband Nanometrics Trillium T120 instruments across an array aperture of approximately 130 kilometers. We used a year of recorded natural ambient noise to determine group and phase velocity surface wave dispersion maps with a 0.1 decimal degree resolution for radial-radial, transverse-transverse, and vertical-vertical components of the empirical Green's function. A grid-search method was used to carry out 1D shear-velocity inversions at each latitude-longitude point and the results were interpolated to produce pseudo-3D shear velocity models. The dispersion maps resolved a zone of slow surface wave velocity south-east of the city of Medina spatially correlated with the 1256 CE eruption. A crustal layer interface at approximately 20 km depth was determined by the inversions for all components, matching the results of prior seismic-refraction studies. Cross-sections of the 3D shear velocity models were compared to gravity measurements obtained in the south-east edge of the field. We found that measurements of low gravity qualitatively correlate with low values of shear-velocity below 20 km along the cross-section profile. We apply these methods to obtain preliminary tomography results on the entire Arabian Shield.

Pollination and reproduction of a self-incompatible forest herb in hedgerow corridors and forest patches.

PubMed

Schmucki, Reto; de Blois, Sylvie

2009-07-01

Habitat-corridors are assumed to counteract the negative impacts of habitat loss and fragmentation, but their efficiency in doing so depends on the maintenance of ecological processes in corridor conditions. For plants dispersing in linear habitats, one of these critical processes is the maintenance of adequate pollen transfer to insure seed production within the corridor. This study focuses on a common, self-incompatible forest herb, Trillium grandiflorum, to assess plant-pollinator interactions and the influence of spatial processes on plant reproduction in hedgerow corridors compared to forests. First, using pollen supplementation experiments over 2 years, we quantified the extent of pollen limitation in both habitats, testing the prediction of greater limitation in small hedgerow populations than in forests. While pollen limitation of fruit and seed set was common, its magnitude did not differ between habitats. Variations among sites, however, suggested an influence of landscape context on pollination services. Second, we examined the effect of isolation on plant reproduction by monitoring fruit and seed production, as well as pollinator activity and assemblage, in small flower arrays transplanted in hedgerows at increasing distances from forest and from each other. We detected no difference in the proportion of flowers setting fruit or in pollinator activity with isolation, but we observed some differences in pollinator assemblages. Seed set, on the other hand, declined significantly with increasing isolation in the second year of the study, but not in the first year, suggesting altered pollen transfer with distance. Overall, plants in hedgerow corridors and forests benefited from similar pollination services. In this system, plant-pollinator interactions and reproduction seem to be influenced more by variations in resource distribution over years and landscapes than by local habitat conditions.

A dense microseismic monitoring network in Korea for uncovering relationship between seismic activity and neotectonic features

NASA Astrophysics Data System (ADS)

Kang, T.; Lee, J. M.; Kim, W.; Jo, B. G.; Chung, T.; Choi, S.

2012-12-01

A few tens of surface traces indicating movements in Quaternary were found in the southeastern part of the Korean Peninsula. Following both the geological and engineering definitions, those features are classified into "active", in geology, or "capable", in engineering, faults. On the other hand, the present-day seismicity of the region over a couple of thousand years is indistinguishable on the whole with the rest of the Korean Peninsula. It is therefore of great interest whether the present seismic activity is related to the neotectonic features or not. Either of conclusions is not intuitive in terms of the present state of seismic monitoring network in the region. Thus much interest in monitoring seismicity to provide an improved observation resolution and to lower the event-detection threshold has increased with many observations of the Quaternary faults. We installed a remote, wireless seismograph network which is composed of 20 stations with an average spacing of 10 km. Each station is equipped with a three-component Trillium Compact seismometer and Taurus digitizer. Instrumentation and analysis advancements are now offering better tools for this monitoring. This network is scheduled to be in operation over about one and a half year. In spite of the relatively short observation period, we expect that the high density of the network enables us to monitor seismic events with much lower magnitude threshold compared to the preexisting seismic network in the region. Following the Gutenberg-Richter relationship, the number of events with low magnitude is logarithmically larger than that with high magnitude. Following this rule, we can expect that many of microseismic events may reveal behavior of their causative faults, if any. We report the results of observation which has been performed over a year up to now.

Evaluation of the new infrastructure for French Permanent Broadband Stations in Auvergne (France).

NASA Astrophysics Data System (ADS)

Douchain, J. M.; Regis, E.; Battaglia, J.; Vergne, J.

2017-12-01

French seismologic and geodetic network (RESIF) is a national equipment for the observation and understanding of the solid Earth. It is an instrument aimed at acquiring new top-quality data for disciplines like seismology, geodesy and gravimetry to advance the understanding of the dynamics of our planet. The seismology component of RESIF, with its homogeneous coverage of the territory, will allow better localisation and characterisation of seismic activityover a wide range of magnitudes as well as provide high quality data for research The Auvergne Seismic Network (ASN) manages seismic stations in the center of france since the beginning of the 80's and continuously ugrades them. Nowadays, 21 stations (velocimeters and accelerometers) are deployed to monitor the Massif Central seismic activity. In the future, the ASN will run 15 broadband stations that will be part of RESIF network. Six of theses sites already have former generation instrumentation (short period sensors buried in the ground, low dynamic) but others are completely new. In june 2017, 4 permanent seismic stations have been upgraded to the new standard installation type for open environment. The chozen infrastructure is a 5 meter drilling equiped with a posthole broadband sensor. Prior to these final installations, on each site, Trillium 120 PA have been installed for 2 temporary experiments. The first one consisted of a direct burial installations at about 80 centimeters depth and lasted for 1 or 2 months. The second dataset was recorded in shallow seismic vaults, during 6 months.In this study, we compare, for each site, data recorded with the 3 configurations in order to evaluate the profits of the new RESIF installations. For this purpose, we compare the probability density fonctions to evaluate noise levels, as well as sprectrograms and hourly detection number. Our results show that the installation of sensors in drillings greatly improves the quality of data at low and high frequencies.

Response of Seismometer with Symmetric Triaxial Sensor Configuration to Complex Ground Motion

NASA Astrophysics Data System (ADS)

Graizer, V.

2007-12-01

Most instruments used in seismological practice to record ground motion in all directions use three sensors oriented toward North, East and upward. In this standard configuration horizontal and vertical sensors differ in their construction because of gravity acceleration always applied to a vertical sensor. An alternative way of symmetric sensor configuration was first introduced by Galperin (1955) for petroleum exploration. In this arrangement three identical sensors are also positioned orthogonally to each other but are tilted at the same angle of 54.7 degrees to the vertical axis (triaxial system of coordinate balanced on its corner). Records obtained using symmetric configuration must be rotated into an earth referenced X, Y, Z coordinate system. A number of recent seismological instruments (e.g., broadband seismometers Streckeisen STS-2, Trillium of Nanometrics and Cronos of Kinemetrics) are using symmetric sensor configuration. In most of seismological studies it is assumed that rotational (rocking and torsion) components of earthquake ground motion are small enough to be neglected. However, recently examples were shown when rotational components are significant relative to translational components of motions. Response of pendulums installed in standard configuration (vertical and two horizontals) to complex input motion that includes rotations has been studied in a number of publications. We consider the response of pendulums in a symmetric sensor configuration to complex input motions including rotations, and the resultant triaxial system response. Possible implications of using symmetric sensor configuration in strong motion studies are discussed. Considering benefits of equal design of all three sensors in symmetric configuration, and as a result potentially lower cost of the three-component accelerograph, it may be useful for strong motion measurements not requiring high resolution post signal processing. The disadvantage of this configuration is that if one of the sensors is not working properly or there is a misalignment of sensors, it results in degradation of all three components. Symmetric sensor configuration requires identical processing of each channel putting a number of limitations on further processing of strong motion records.

Manta A New BroadBand OBS

NASA Astrophysics Data System (ADS)

Hello, Y.; Yegikyan, M.; Charvis, P.; Philippe, O.

2017-12-01

Manta is a new BroadBand OBS developed at Geoazur and commercialized by Osean. The design is inspired by 3-years autonomy MUG-OBS a Multiparameter Ocean Bottom System which carry a lot of sort of sensor types. As Mug-OBS, Manta-OBS rated 6000m is designed to resist a trawling. All the components are non corrosive such polyethylene, titanium and buoyancy is ensured by syntactic foam. Equipped in standard version with a Trillium compact OBS Manta has an autonomy of 18 months, but can accept on its 4 input channels any kind of signal as low as from an hydrophone or larger from other type of a seismometer or accelerometer. Tri-axial geophones unit (2 Hz or 4.5 Hz ) can replace the seismometer and will expend the lifespan for the instrument. The seismometer is encapsulated in a central well established by four panels of the main structure to protect it from sea current convection and is decoupled from main chassis. An health bulletin is recoverable by acoustic any time to facilitate the installation and during a visit when instrument is deployed. Main parameters for acquisition can be changed by acoustics command from surface at any time. Once at the bottom, release for the main sensor installation is programmed on a timer but controlled by the tilt of the OBS. If the tilt is too important based on programmed limits, sensor will not released automatically, but this can be forced by acoustic command after returning the tilt informations to the boat operator. Manta is equipped with flash light and AIS system for easy location at recovery, and can also send it's position by Iridium satellite in case of an unexpected ascent such caused by a possible trawling if deployed in shallow water. Clock drift calculation is automatically made against GPS time signal once the OBS return at the surface. The recovery of the OBS is initiated by an acoustic command. These new features made Manta a very versatile instrument for monitoring earthquakes.

Monitoring Seasonal Changes in Permafrost Using Seismic Interferometry

NASA Astrophysics Data System (ADS)

James, S. R.; Knox, H. A.; Abbott, R. E.

2015-12-01

The effects of climate change in polar regions and their incorporation in global climate models has recently become an area of great interest. Permafrost holds entrapped greenhouse gases, e.g. CO2 and CH4, which are released to the atmosphere upon thawing, creating a positive feedback mechanism. Knowledge of seasonal changes in active layer thickness as well as long term degradation of permafrost is critical to the management of high latitude infrastructures, hazard mitigation, and increasing the accuracy of climate predictions. Methods for effectively imaging the spatial extent, depth, thickness, and discontinuous nature of permafrost over large areas are needed. Furthermore, continuous monitoring of permafrost over annual time scales would provide valuable insight into permafrost degradation. Seismic interferometry using ambient seismic noise has proven effective for recording velocity changes within the subsurface for a variety of applications, but has yet to be applied to permafrost studies. To this end, we deployed 7 Nanometrics Trillium posthole broadband seismometers within Poker Flat Research Range, located 30 miles north of Fairbanks, Alaska in a zone of discontinuous permafrost. Approximately 2 years worth of nearly continuous ambient noise data was collected. Using the python package MSNoise, relative changes in velocity were calculated. Results show high amounts of variability throughout the study period. General trends of negative relative velocity shifts can be seen between August and October followed by a positive relative velocity shift between November and February. Differences in relative velocity changes with both frequency and spatial location are also observed, suggesting this technique is sensitive to permafrost variation with depth and extent. Overall, short and long term changes in shallow subsurface velocity can be recovered using this method proposing seismic interferometry is a promising new technique for permafrost monitoring. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Finite frequency P-wave traveltime measurements on ocean bottom seismometers and hydrophones in the western Indian Ocean

NASA Astrophysics Data System (ADS)

Tsekhmistrenko, Maria; Sigloch, Karin; Hosseini, Kasra; Barruol, Guilhem

2016-04-01

From 2011 to 2014, the RHUM-RUM project (Reunion Hotspot Upper Mantle - Reunions Unterer Mantel) instrumented a 2000x2000km2 area of Indian Ocean seafloor, islands and Madagascar with broadband seismometers and hydrophones. The central component was a 13-month deployment of 57 German and French Ocean Bottom Seismometers (OBS) in 2300-5600 m depth. This was supplemented by 2-3 year deployments of 37 island stations on Reunion, Mauritius, Rodrigues, the southern Seychelles, the Iles Eparses and southern Madagascar. Two partner projects contributed another 30+ stations on Madagascar. Our ultimate objective is multifrequency waveform tomography of the entire mantle column beneath the Reunion hotspot. Ideally we would use all passbands that efficiently transmit body waves but this meets practical limits in the noise characteristics of ocean-bottom recordings in particular. Here we present the preliminary data set of frequency-dependent P-wave traveltime measurements on seismometers and hydrophones, obtained by cross-correlation of observed with predicted waveforms. The latter are synthesized from fully numerical Green's functions and carefully estimated, broadband source time functions. More than 200 teleseismic events during the 13-month long deployment yielded usable P-waveform measurements. We present our methods and discuss data yield and quality of ocean-bottom versus land seismometers, and of OBS versus broadband hydrophones. Above and below the microseismic noise band, data yields are higher than within it, especially for OBS. The 48 German OBS, equipped with Guralp 60 s sensors, were afflicted by relatively high self-noise compared to the 9 French instruments equipped with Nanometrics Trillium 240 s sensors. The HighTechInc (model HTI-01 and HTI-04-PCA/ULF) hydrophones (100 s corner period) functioned particularly reliably but their waveforms are relatively more challenging to model due to reverberations in the water column. We obtain ~15000 combined cross-correlations measurements that should be usable in multifrequency P-wave tomography, in passbands between 30 s and 2.7 s dominant period.

Assessing plant community composition fails to capture impacts of white-tailed deer on native and invasive plant species.

PubMed

Nuzzo, Victoria; Dávalos, Andrea; Blossey, Bernd

2017-07-01

Excessive herbivory can have transformative effects on forest understory vegetation, converting diverse communities into depauperate ones, often with increased abundance of non-native plants. White-tailed deer are a problematic herbivore throughout much of eastern North America and alter forest understory community structure. Reducing (by culling) or eliminating (by fencing) deer herbivory is expected to return understory vegetation to a previously diverse condition. We examined this assumption from 1992 to 2006 at Fermilab (Batavia, IL) where a cull reduced white-tailed deer ( Odocoileus virginianus ) abundance in 1998/1999 by 90 % from 24.6 to 2.5/km 2 , and at West Point, NY, where we assessed interactive effects of deer, earthworms, and invasive plants using 30 × 30 m paired fenced and open plots in 12 different forests from 2009 to 2012. We recorded not only plant community responses (species presence and cover) within 1 m 2 quadrats, but also responses of select individual species (growth, reproduction). At Fermilab, introduced Alliaria petiolata abundance initially increased as deer density increased, but then declined after deer reduction. The understory community responded to the deer cull by increased cover, species richness and height, and community composition changed but was dominated by early successional native forbs. At West Point plant community composition was affected by introduced earthworm density but not deer exclusion. Native plant cover increased and non-native plant cover decreased in fenced plots, thus keeping overall plant cover similar. At both sites native forb cover increased in response to deer reduction, but the anticipated response of understory vegetation failed to materialize at the community level. Deer-favoured forbs ( Eurybia divaricata , Maianthemum racemosum , Polygonatum pubescens and Trillium recurvatum ) grew taller and flowering probability increased in the absence of deer. Plant community monitoring fails to capture initial and subtle effects of reduced or even cessation of deer browse on browse sensitive species. Measuring responses of individual plants (growth, flowering and reproductive success) provides a more sensitive and powerful assessment of forest understory responses to deer management.

First deployment of a Multiparameter Ocean Bottom System in the Mediterranean sea

NASA Astrophysics Data System (ADS)

Hello, Y.; Charvis, P.; Yegikyan, M.; Rivet, D.; Deschamps, A.

2016-12-01

Continuous monitoring of oceans is the next great scientific and technical challenge. Recently several cabled sea bottom observatories were developed in Canada (Neptune), in Japan (DONET) and in France (Antares) for real time monitoring of seismic activity, dynamics of the water column, global environmental changes, observation of marine life, the detection of neutrinos, etc. Nevertheless, these initiatives are costly to install and to maintain and it is unlikely that we can deploy many similar observatories in the near future. Among the most recent alternative we developed a 3-years autonomy system equipped with a Nanometrics Trillium 120 s, a triaxial accelerometer, a differential and an absolute pressure gauge, and a hydrophone. MUG-OBS (Multiparameter Geophysical Ocean Bottom system) is a free falling instrument rated down to 6000 m for the monitoring of geophysical signals (earthquakes, submarine landslides, other transient signals, …). The major innovation is that it is possible to recover the data any time on demand (regularly every 6-months or after a crisis) using one of the 6 data-shuttles released from the surface by acoustic command. The MUG-OBS prototype was tested in situ twice for a short period of one week in the bay of Villefranche-sur-mer (French Riviera) in November 2015 and March 2016. During these periods we were lucky to record several teleseismic events with an excellent signal to noise ratio. In September 2016 the instrument will be deployed in the Ligurian sea, 35 miles offshore the city of Nice, for a three-years period, to extend offshore the regional land seismic network. We will present the first seismic signals available from this new instrument. MUG-OBS is a user friendly design and once installed can be maintained by non-specialists to recover data using ship of opportunity. This make it a good challenger to be deployed along the subduction of South America in the frame of the future Subduction Zone Observatory. Such a sea bottom system could also be equipped with other sensors (ADCP, underwater Methane sensor, CO2 flow-through sensor,…) and could be used as a multidisciplinary platform for the environmental monitoring of the deep Ocean.

MUG-OBS - Multiparameter Geophysical Ocean Bottom System : a new instrumental approach to monitor earthquakes.

NASA Astrophysics Data System (ADS)

Hello, Y.; Yegikyan, M.; Charvis, P.; Verfaillie, R.; Philippe, O.

2015-12-01

There are several attempts to monitor real time seismic activity, using regional scale wired nodes, such as Neptune in Canada and in the U.S, Antares in France or DONET in Japan.On another hand there are also initiatives in deploying repeatedly OBS array like during the amphibious Cascadia Initiative (four 1-year deployments), the Japanese Pacific Array (broadband OBSs "ocean-bottom broadband dispersion survey" with 2-years autonomy), the Obsismer program in the French Lesser Antilles (eight 6-months deployments) and the Osisec program in Ecuador (four 6-months deployments). These OBSs are autonomous, they are self-recovered or recovered using an ROV. These systems are costly including ship time, and require to recover the OBS before to start working on data.Among the most recent alternative we developed a 3-years autonomy OBS equipped with a Nanometrics Trillium 120 s, a triaxial accelerometer, a differential, an absolute pressure gauge, and a hydrophone. MUG-OBS is a free falling instrument rated down to 6000 m. The installation of the sensor is monitored by acoustic commands from the surface and a health bulletin with data checking is recovered by acoustic during the installation. The major innovation is that it is possible to recover the data any time on demand (regularly every 6-months or after a seismic crisis) utilizing one of the 6 data-shuttles released from the surface by acoustic command using a one day fast cruise boat of opportunity. Since sensors stayed at the same location for 3 years (when an OBS is redeployed on the same site, it will not land in the same place), it is a perfect tool to monitor slow seismic events, background seismic activity and aftershock distribution. Clock, drift measurement and GPS localization is automatic when the shuttle reaches the surface. A new version is being developed; for remote areas, shuttles released automatically and a seismic events bulletin is transmitted. Selected data can be recovered by two- way Iridium satellite communication. After a period of 3 years the main station is ­self-recovered by acoustic.

Monitoring the development of volcanic eruptions through volcanic lightning - Using a lightning mapping array, seismic and infrasound array, and visual plume analysis

NASA Astrophysics Data System (ADS)

Smith, C. M.; Thompson, G.; McNutt, S. R.; Behnke, S. A.; Edens, H. E.; Van Eaton, A. R.; Gaudin, D.; Thomas, R. J.

2017-12-01

The period of 28 May - 7 June 2015 at Sakurajima Volcano, Japan witnessed a multitude of Vulcanian eruptive events, which resulted in plumes reaching 500-3000m above the vent. These plumes varied from white, gas-rich plumes to dark grey and black ash-rich plumes, and were recorded on lowlight and infrared cameras. A nine-station lightning mapping array (LMA) was deployed to locate sources of VHF (67-73 MHz) radiation produced by lightning flashes and other types of electrical activity such as `continuous RF (radio frequency)'. Two Nanometrics Trillium broadband seismometers and six BSU infrasound sensors were deployed. Over this ten day period we recorded 1556 events that consisted of both seismic and infrasound signals, indicating explosive activity. There are an additional 1222 events that were recorded as only seismic or infrasound signals, which may be a result of precursory seismic signals or noise contamination. Plume discharge types included both distinct lightning flashes and `continuous RF'. The LMA ran continuously for the duration of the experiment. On 30 May 2015 at least seven lightning flashes were also detected by the Vaisala Global Lightning Detection 360 network, which detects VLF (3-30 kHz) radiation. However the University of Washington's World Wide Lightning Location Network, which also detects VLF radiation, detected no volcanic lightning flashes in this time period. This indicates that the electrical activity in Sakurajima's plume occurs near the lower limits of the VLF detection threshold. We investigate relationships between the plume dynamics, the geophysical signal and the corresponding electrical activity through: plume velocity and height; event waveform cross-correlation; volcano acoustic-seismic ratios; overall geophysical energy; RSAM records; and VHF sources detected by the LMA. By investigating these relationships we hope to determine the seismic/infrasound energy threshold required to generate measurable electrical activity. Seismic and infrasound are two of the most common volcanic monitoring methods. By developing the relationships between plume electrification and these geophysical methods we hope to expand the use of lightning for active volcano monitoring.

Assessing plant community composition fails to capture impacts of white-tailed deer on native and invasive plant species

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nuzzo, Victoria; Davalos, Andrea; Blossey, Bernd

Excessive herbivory can have transformative effects on forest understory vegetation, converting diverse communities into depauperate ones, often with increased abundance of non-native plants. White-tailed deer are a problematic herbivore throughout much of eastern North America and alter forest understory community structure. Reducing (by culling) or eliminating (by fencing) deer herbivory is expected to return understory vegetation to a previously diverse condition. We examined this assumption from 1992 to 2006 at Fermilab (Batavia, IL) where a cull reduced white-tailed deer ( Odocoileus virginianus) abundance in 1998/1999 by 90 % from 24.6 to 2.5/km 2, and at West Point, NY, where wemore » assessed interactive effects of deer, earthworms, and invasive plants using 30 × 30 m paired fenced and open plots in 12 different forests from 2009 to 2012. We recorded not only plant community responses (species presence and cover) within 1 m 2 quadrats, but also responses of select individual species (growth, reproduction). At Fermilab, introduced Alliaria petiolata abundance initially increased as deer density increased, but then declined after deer reduction. The understory community responded to the deer cull by increased cover, species richness and height, and community composition changed but was dominated by early successional native forbs. At West Point plant community composition was affected by introduced earthworm density but not deer exclusion. Native plant cover increased and non-native plant cover decreased in fenced plots, thus keeping overall plant cover similar. At both sites native forb cover increased in response to deer reduction, but the anticipated response of understory vegetation failed to materialize at the community level. Deer-favoured forbs ( Eurybia divaricata, Maianthemum racemosum, Polygonatum pubescens and Trillium recurvatum) grew taller and flowering probability increased in the absence of deer. Plant community monitoring fails to capture initial and subtle effects of reduced or even cessation of deer browse on browse sensitive species. As a result, measuring responses of individual plants (growth, flowering and reproductive success) provides a more sensitive and powerful assessment of forest understory responses to deer management.« less

Benchmarking passive seismic methods of estimating the depth of velocity interfaces down to ~300 m

NASA Astrophysics Data System (ADS)

Czarnota, Karol; Gorbatov, Alexei

2016-04-01

In shallow passive seismology it is generally accepted that the spatial autocorrelation (SPAC) method is more robust than the horizontal-over-vertical spectral ratio (HVSR) method at resolving the depth to surface-wave velocity (Vs) interfaces. Here we present results of a field test of these two methods over ten drill sites in western Victoria, Australia. The target interface is the base of Cenozoic unconsolidated to semi-consolidated clastic and/or carbonate sediments of the Murray Basin, which overlie Paleozoic crystalline rocks. Depths of this interface intersected in drill holes are between ~27 m and ~300 m. Seismometers were deployed in a three-arm spiral array, with a radius of 250 m, consisting of 13 Trillium Compact 120 s broadband instruments. Data were acquired at each site for 7-21 hours. The Vs architecture beneath each site was determined through nonlinear inversion of HVSR and SPAC data using the neighbourhood algorithm, implemented in the geopsy modelling package (Wathelet, 2005, GRL v35). The HVSR technique yielded depth estimates of the target interface (Vs > 1000 m/s) generally within ±20% error. Successful estimates were even obtained at a site with an inverted velocity profile, where Quaternary basalts overlie Neogene sediments which in turn overlie the target basement. Half of the SPAC estimates showed significantly higher errors than were obtained using HVSR. Joint inversion provided the most reliable estimates but was unstable at three sites. We attribute the surprising success of HVSR over SPAC to a low content of transient signals within the seismic record caused by low levels of anthropogenic noise at the benchmark sites. At a few sites SPAC waveform curves showed clear overtones suggesting that more reliable SPAC estimates may be obtained utilizing a multi-modal inversion. Nevertheless, our study indicates that reliable basin thickness estimates in the Australian conditions tested can be obtained utilizing HVSR data from a single seismometer, without a priori knowledge of the surface-wave velocity of the basin material, thereby negating the need to deploy cumbersome arrays.

Automated analysis of flow cytometric data for measuring neutrophil CD64 expression using a multi-instrument compatible probability state model.

PubMed

Wong, Linda; Hill, Beth L; Hunsberger, Benjamin C; Bagwell, C Bruce; Curtis, Adam D; Davis, Bruce H

2015-01-01

Leuko64™ (Trillium Diagnostics) is a flow cytometric assay that measures neutrophil CD64 expression and serves as an in vitro indicator of infection/sepsis or the presence of a systemic acute inflammatory response. Leuko64 assay currently utilizes QuantiCALC, a semiautomated software that employs cluster algorithms to define cell populations. The software reduces subjective gating decisions, resulting in interanalyst variability of <5%. We evaluated a completely automated approach to measuring neutrophil CD64 expression using GemStone™ (Verity Software House) and probability state modeling (PSM). Four hundred and fifty-seven human blood samples were processed using the Leuko64 assay. Samples were analyzed on four different flow cytometer models: BD FACSCanto II, BD FACScan, BC Gallios/Navios, and BC FC500. A probability state model was designed to identify calibration beads and three leukocyte subpopulations based on differences in intensity levels of several parameters. PSM automatically calculates CD64 index values for each cell population using equations programmed into the model. GemStone software uses PSM that requires no operator intervention, thus totally automating data analysis and internal quality control flagging. Expert analysis with the predicate method (QuantiCALC) was performed. Interanalyst precision was evaluated for both methods of data analysis. PSM with GemStone correlates well with the expert manual analysis, r(2) = 0.99675 for the neutrophil CD64 index values with no intermethod bias detected. The average interanalyst imprecision for the QuantiCALC method was 1.06% (range 0.00-7.94%), which was reduced to 0.00% with the GemStone PSM. The operator-to-operator agreement in GemStone was a perfect correlation, r(2) = 1.000. Automated quantification of CD64 index values produced results that strongly correlate with expert analysis using a standard gate-based data analysis method. PSM successfully evaluated flow cytometric data generated by multiple instruments across multiple lots of the Leuko64 kit in all 457 cases. The probability-based method provides greater objectivity, higher data analysis speed, and allows for greater precision for in vitro diagnostic flow cytometric assays. © 2015 International Clinical Cytometry Society.

Development of compact long-term broadband ocean bottom seismometer for seafloor observation of slow earthquakes

NASA Astrophysics Data System (ADS)

Yamashita, Y.; Shinohara, M.; Yamada, T.; Shiobara, H.

2017-12-01

It is important to understand coupling between plates in a subduction zone for studies of earthquake generation. Recently low frequency tremor and very low frequency earthquake (VLFE) were discovered in plate boundary near a trench. These events (slow earthquakes) in shallow plate boundary should be related to slow slip on a plate boundary. For observation of slow earthquakes, Broad Band Ocean Bottom Seismometer (BBOBS) is useful, however a number of BBOBSs are limited due to cost. On the other hand, a number of Long-term OBSs (LT-OBSs) with recording period of one year are available. However, the LT-OBS has seismometer with a natural period of 1 second. Therefore frequency band of observation is slightly narrow for slow earthquakes. Therefore we developed a compact long-term broad-band OBS by replacement of the seismic sensor of the LT-OBSs to broadband seismometer.We adopted seismic sensor with natural period of 20 seconds (Trillium Compact Broadband Seismometer, Nanometrics). Because tilt of OBS on seafloor can not be controlled due to free-fall, leveling system for seismic sensor is necessary. The broadband seismic senor has cylinder shape with diameter of 90 mm and height of 100 mm, and the developed levelling system can mount the seismic sensor with no modification of shape. The levelling system has diameter of 160 mm and height of 110 mm, which is the same size as existing levelling system of the LT-OBS. The levelling system has two horizontal axes and each axis is driven by motor. Leveling can be performed up to 20 degrees by using micro-processor (Arduino). Resolution of levelling is less than one degree. The system immediately starts leveling by the power-on of controller. After levelling, the the seismic senor is powered and the controller records angles of levelling to SD RAM. Then the controller is shut down to consume no power. Compact long-term broadband ocean bottom seismometer is useful for observation of slow earthquakes on seafloor. In addition, seafloor observations of teleseismic events and deep earthquakes to estimate seismic structure of deep regions and observations of submarine volcanoes are expected.

Assessing plant community composition fails to capture impacts of white-tailed deer on native and invasive plant species

DOE PAGES

Nuzzo, Victoria; Davalos, Andrea; Blossey, Bernd

2017-06-08

Excessive herbivory can have transformative effects on forest understory vegetation, converting diverse communities into depauperate ones, often with increased abundance of non-native plants. White-tailed deer are a problematic herbivore throughout much of eastern North America and alter forest understory community structure. Reducing (by culling) or eliminating (by fencing) deer herbivory is expected to return understory vegetation to a previously diverse condition. We examined this assumption from 1992 to 2006 at Fermilab (Batavia, IL) where a cull reduced white-tailed deer ( Odocoileus virginianus) abundance in 1998/1999 by 90 % from 24.6 to 2.5/km 2, and at West Point, NY, where wemore » assessed interactive effects of deer, earthworms, and invasive plants using 30 × 30 m paired fenced and open plots in 12 different forests from 2009 to 2012. We recorded not only plant community responses (species presence and cover) within 1 m 2 quadrats, but also responses of select individual species (growth, reproduction). At Fermilab, introduced Alliaria petiolata abundance initially increased as deer density increased, but then declined after deer reduction. The understory community responded to the deer cull by increased cover, species richness and height, and community composition changed but was dominated by early successional native forbs. At West Point plant community composition was affected by introduced earthworm density but not deer exclusion. Native plant cover increased and non-native plant cover decreased in fenced plots, thus keeping overall plant cover similar. At both sites native forb cover increased in response to deer reduction, but the anticipated response of understory vegetation failed to materialize at the community level. Deer-favoured forbs ( Eurybia divaricata, Maianthemum racemosum, Polygonatum pubescens and Trillium recurvatum) grew taller and flowering probability increased in the absence of deer. Plant community monitoring fails to capture initial and subtle effects of reduced or even cessation of deer browse on browse sensitive species. As a result, measuring responses of individual plants (growth, flowering and reproductive success) provides a more sensitive and powerful assessment of forest understory responses to deer management.« less

The Seismic Broad Band Western Mediterranean (wm) Network and the Obs Fomar Pool: Current state and Obs activities.

NASA Astrophysics Data System (ADS)

Pazos, Antonio; Davila, Jose Martin; Buforn, Elisa; Bezzeghoud, Mourad; Harnafi, Mimoun; Mattesini, Mauricio; Caldeira, Bento; Hanka, Winfried; El Moudnib, Lahcen; Strollo, Angelo; Roca, Antoni; Lopez de Mesa, Mireya; Dahm, Torsten; Cabieces, Roberto

2016-04-01

The Western Mediterranean (WM) seismic network started in 1996 as an initiative of the Royal Spanish Navy Observatory (ROA) and the Universidad Complutense de Madrid (UCM), with the collaboration of the GeoForschungsZentrum (GFZ) of Potsdam. A first broad band seismic station (SFUC) was installed close to Cádiz (South Spain). Since then, additional stations have been installed in the Ibero-Moghrebian region. In 2005, the "WM" code was assigned by the FDSN and new partners were jointed: Evora University (UEVO, Portugal), the Scientifique Institute of Rabat (ISRABAT, Morocco), and GFZ. Now days, the WM network is composed by 15 BB stations, all of them with Streckaisen STS-2 or STS-2.5 sensors, Quanterra or Earthdata digitizers and SeiscomP. Most them have co-installed a permanent geodetic GPS stations, and some them also have an accelerometer. There are 10 stations deployed in Spanish territory (5 in the Iberian peninsula, 1 in Balearic islands and 4 in North Africa Spanish places) with VSAT or Internet communications, 2 in Portugal (one of them without real time), and 3 in Morocco (2 VSAT and 1 ADSL). Additionally, 2 more stations (one in South Spain and one in Morocco) will be installed along this year. Additionally ROA has deployed a permanent real time VBB (CMG-3T: 360s) station at the Alboran Island. Due to the fact that part of the seismic activity is located at marine areas, and also because of the poor geographic azimuthal coverage at some zones provided by the land stations (specially in the SW of the San Vicente Cape area), ROA and UCM have acquired six broad band "LOBSTERN" OBS, manufactured by KUM (Kiel, Germany), conforming the OBS FOMAR pool. Three of them with CMG-40T sensor and the other with Trillium 120. These OBS were deployed along the Gibraltar strait since January to November 2014 to study the microseismicity in the Gibraltar strait area. In September 2015 FOMAR network has been deployed in SW of the San Vicente Cape for 8 months as a part of ALERTES-RIM project. In this work the current state and future plans of the WM network, the results of the Gibraltar strait campaign and San Vicente Cape OBS experiment are shown.

Temporary Seismic Installation in Eastern Bangladesh: Microseismicity and Structure of an On-Land Accretionary Prism

NASA Astrophysics Data System (ADS)

Foster, A. E.; Almeida, R. V.; Akhter, S. H.; Hubbard, J.; Bhattacharya, R.; Shing, U. M.; Hosain, A.; Bulbul, M. A.

2016-12-01

Eastern Bangladesh is underlain by a fold and thrust belt accumulating 13-17 mm/yr of plate convergence on a locked, shallowly dipping décollement (Steckler et al., 2016). We have installed a network of short-period and broadband instruments in this region to better assess microseismicity and investigate the structure of the fold belt. Stations will remain in place for 1-2 years and will complement the temporary stations installed by the University of Dhaka and the Lamont-Doherty Earth Observatory. Thirteen Lennartz 1-Hz instruments and three Trillium Compact 120-s instruments were installed in the Sylhet area in June 2016. Station spacing is between 15-30 km. Installations ranged from shallow vaults to above-ground locations on solid foundations, as required by local conditions. One focus of this deployment is to locate microseismicity. Neither large numbers nor magnitudes of earthquakes are expected in this area, but improved locations may help define active areas of the convergence as well as illuminate the interactions between the Dauki fault (responsible for uplift of the Shillong Plateau), the Sylhet anticline, and the rest of the Indo-Burman Ranges. Nine additional short-period instruments and three additional broadband instruments will be installed in the Chittagong area in September 2016. The southern-most stations are located over the Andaman subduction zone, thought to be associated with a large subduction earthquake in 1762 (Steckler et al., 1998). Thus, the full deployment will span the transition from an on-land accretionary prism to an area considered a classic subduction zone. Combined, the northern and southern parts of the network should provide good locations for events within the Tripura area (India) as well. We present initial estimates of station quality and the potential for an earthquake catalogue. We plan to obtain earthquake locations and focal mechanisms, when possible, as the data is collected. We will apply ambient noise tomography methods to investigate the structure of the fold belt. These applications and others may contribute to unanswered questions in the area, such as the location of the frontal-most deformation associated with the fold and thrust belt and the geometry of the basal décollement at depth, and allow better characterization of the risk to nearby populations.

Back-Projection Imaging of extended, high-frequency pre-, co-, and post-eruptive seismicity at El Jefe Geyser, El Tatio Geyser Field, Chile

NASA Astrophysics Data System (ADS)

Kelly, C. L.; Lawrence, J. F.; Beroza, G. C.

2017-12-01

El Tatio Geyser Field in northern Chile is the third largest geyser field in the world. It is comprised of 3 basins that span 10 km x 10 km at an average elevation of 4250 m and contains at least 80 active geysers. Heavy tourist traffic and previous geothermal exploration make the field relatively non-pristine and ideal for performing minimally invasive geophysical experiments. We deployed a dense array of 51 L-28 3-component geophones (1-10 m spacing, corner frequency 4.5 Hz, 1000 Hz sample rate), and 6 Trillium 120 broadband seismometers (2-20 m spacing, long period corner 120 s, 500 Hz sample rate) in a 50 m x 50 m grid in the central Upper Geyser Basin (the largest basin in area at 5 km x 5 km) during October 2012 as part of a collaborative study of hydrothermal systems between Stanford University; U.C. Berkeley; U. of Chile, Santiago; U. of Tokyo; and the USGS. The seismic array was designed to target at El Jefe Geyser (EJG), a columnar geyser (eruption height 1-1.5 m) with a consistent periodic eruption cycle of 132 +/- 3 s. Seismicity at EJG was recorded continuously for 9 days during which 6000 total eruptions occurred. Excluding periods of high anthropogenic noise (i.e. tourist visits, field work), the array recorded 2000 eruptions that we use to create 4D time-lapse images of the evolution of seismic source locations before, during and after EJG eruptions. We use a new back-projection processing technique to locate geyser signals, which tend to be harmonic and diffuse in nature, during characteristic phases of the EJG eruption cycle. We obtain Vp and Vs from ambient-field tomography and estimates of P and S propagation from a hammer source recorded by the array. We use these velocities to back-project and correlate seismic signals from all available receiver-pairs to all potential source locations in a subsurface model assuming straight-line raypaths. We analyze results for individual and concurrent geyser sources throughout an entire EJG eruption cycle and over multiple eruption cycles. We target specific seismic observations by restricting the frequency band of analysis (i.e., high or low frequency bands), and use our results to evaluate changes in source distributions before, during and after eruptions and compare them to synchronous surface observations (downhole pressure/temperature, discharge rate, thermal video).

Analysis of volcano-related seismicity to constrain the magmatic plumbing system beneath Fogo, Cape Verde, by (multi-)array techniques

NASA Astrophysics Data System (ADS)

Dietrich, Carola; Wölbern, Ingo; Faria, Bruno; Rümpker, Georg

2017-04-01

Fogo is the only island of the Cape Verde archipelago with regular occurring volcanic eruptions since its discovery in the 15th century. The volcanism of the archipelago originates from a mantle plume beneath an almost stationary tectonic plate. With an eruption interval of approximately 20 years, Fogo belongs to the most active oceanic volcanoes. The latest eruption started in November 2014 and ceased in February 2015. This study aims to characterize and investigate the seismic activity and the magmatic plumbing system of Fogo, which is believed to be related to a magmatic source close to the neighboring island of Brava. According to previous studies, using conventional seismic network configurations, most of the seismic activity occurs offshore. Therefore, seismological array techniques represent powerful tools in investigating earthquakes and other volcano-related events located outside of the networks. Another advantage in the use of seismic arrays is their possibility to detect events of relatively small magnitude and to locate seismic signals without a clear onset of phases, such as volcanic tremors. Since October 2015 we have been operating a test array on Fogo as part of a pilot study. This array consists of 10 seismic stations, distributed in a circular shape with an aperture of 700 m. The stations are equipped with Omnirecs CUBE dataloggers, and either 4.5 Hz geophones (7 stations) or Trillium-Compact broad-band seismometers (3 stations). In January 2016 we installed three additional broad-band stations distributed across the island of Fogo to improve the capabilities for event localization. The data of the pilot study is dominated by seismic activity around Brava, but also exhibit tremors and hybrid events of unknown origin within the caldera of Fogo volcano. The preliminary analysis of these events includes the characterization and localization of the different event types using seismic array processing in combination with conventional localization methods. In the beginning of August 2016, a "seismic crisis" occurred on the island of Brava which led to the evacuation of a village. The seismic activity recorded by our instruments on Fogo exhibits more than 40 earthquakes during this time. Locations and magnitudes of these events will be presented. In January 2017 the pilot project discussed here will be complemented by three additional seismic arrays (two on Fogo, one on Brava) to improve seismic event localization and structural imaging based on scattered seismic phases by using multi-array techniques. Initial recordings from the new arrays are expected to be available by April 2017.

A Dense Small-Scale Seismic Network in the Ngorongoro Conservation Area (Northern Tanzania)

NASA Astrophysics Data System (ADS)

Parisi, L.; Lombardo, L.; Rodriguez-Mustafa, M.; Mai, P. M.

2017-12-01

A temporary deployment consisting of sixteen broadband seismic stations is conducted for the first time in the Ngorongoro Conservation Area (NCA, Northern Tanzania), located at the boundary between the Tanzanian Craton and East African Rift. A deep knowledge of the faulting systems and tectonics of the area is needed to better understand the contribution of the synsedimentary faults to the deposition of the Olduvai and surrounding basins affecting the landscapes of the Homo Habilis first settlements. Complex fault systems have been mapped in the field but their connection, especially at depth, is not well known. A first batch of ten instruments was installed in June 2016. In June 2017 two stations were dismissed and a second batch of six stations was installed in new locations. The current network of fourteen stations will record until May 2018. Stations are equipped with Nanometrics Trillium Compact Posthole 120 s sensor and Centaur digitiser recording continuously at 200 Hz. The whole network covers 1400 km2 and station interspace ranges from 8 to 15 km. We analyse probabilistic power spectra densities of the seismic noise to obtain insights of its origin and test the performances of the stations. Although factories do not exist in the area and most of the stations are far from roads, ambient noise in the range 0.01 - 1 s is relatively high (between -120 dB and -100dB at 0.1 s) probably because of the abundance of livestock living in the NCA. Ambient noise in the period range 1 - 10 s (secondary microseisms) decreases from east to west. Although the main source of the microseisms is located in the Indian Ocean (east of the study area), a contribution from the low period tremors coming from the nearby active volcano Ol Doinyo Lengai (north-east of the study area) is expected. Whereas the longer period noise (10 - 100 s) is very low in the vertical component seismograms, it is higher than the high noise model in the horizontal components for most of the stations. Although this can be due to sensor insulation issues, we find a strong variability even for sensors installed in the same conditions. We also present the first seismicity map of the NCA by using the first year of data. We detect events with ML ranging between 0.7 and 3.0, mostly located south where major fault systems have not been mapped at the surface yet.

Preliminary results of receiver function analysis of seismic data recorded from a broadband deployment across the Gulf Coast Plain

NASA Astrophysics Data System (ADS)

Gurrola, H.; Pratt, K. W.; Pulliam, J.; Dunbar, J. A.

2011-12-01

In summer of 2010, 21 broadband seismographs were installed at 16-18 km spacing along a transect running from Johnson City, TX, (on the Edwards Plateau), to Matagorda Island to study the current structure of this rifted passive margin. The large magnetic anomaly that parallels the coast throughout the Gulf region moves on-shore beneath our transect such that we will be able to investigate the source of this anomaly. A second important target that will be imaged in this Balcones fault which is associated with the Ouachita front. This project is funded by a grant from the Norman Hackerman Advanced Research Program (NHARP), a biannual competition among Texas Universities to support research, and makes use of Texas Tech, Baylor, and UT Austin equipment. As a result, the deployment includes a less uniform array of seismic equipment, (10 Trillium compact seismometers and 10 Guralps; including 40Ts, 3Ts and 3ESPs), than projects supported by the IRIS PASSCAL center. Our vault construction was similar to Flexible array vaults, but Gulf Coast provides a more challenging environment for deployment than most encountered in the western US. The shallow water table and loose sediment can become almost fluid when storms deluge the area with rain. In dry periods, mud cracks near the vaults cause the vaults to tilt. As a result, even high quality, shallow seismic vaults can "float" or shift sufficiently to cause one or two components of the seismic stations to drift against their stops in days or weeks. As a result, the only data consistently available from all our stations, are vertical components. Horizontal component data from the summer of 2010 can be hit and miss due to the tilting of the vaults. These issues have been reduced in the summer of 2011 due to the drought. To address the data's shortcomings, we will average the vertical components from our stations and nearby EarthScope TA stations, (up 300 km away), to isolate the cleanest representation of the incoming P-wave, (with local PPp reverberations averaged out). This is essentially beam forming for the optimal teleseismic ray path. The clean P-wave will then be deconvolved from the vertical components at each station to produce a vertical component receiver function that will enable us to model and stack local P-wave reverberations to produce a 2-D image of lithospheric structure. To produce traditional receiver functions from time periods where one component is lost from several stations, we will treat neighboring stations as arrays and recover an "array averaged three-component seismogram" for each loacation. These "beamed" seismograms will allow imaging of the crust, lithospheric mantle, and transition zone beneath the broadband array using traditional receiver function stacking or migration.

Strategy for the deployment of a dense broadband temporary array in the Alps: lessons learnt from the CIFALPS experiment

NASA Astrophysics Data System (ADS)

Coralie, Aubert; Anne, Paul; Stefano, Solarino; Sandrine, Roussel; Simone, Salimbeni; Pierre, Zangelmi; Glenn, Cougoulat; Yinshuang, Ai; Weiwei, Xu; Yumei, He; Liang, Zhao

2013-04-01

The CIFALPS (China-Italy-France Alps seismic survey) experiment is a common project of IGGCAS (China), ISTerre (France) and INGV (Italy). It aims at getting new high-resolution passive seismic data on the crustal and upper mantle structure of the southwestern Alps. In this framework, we have installed a temporary broadband seismic array across the southwestern Alps from the Rhône valley (France) to the Po plain (Italy). The main sub-array of CIFALPS is a 350-km long roughly linear profile of 46 stations trending WSW-ENE from Bollène (France) to north of Alessandria (Italy). The average station spacing is 10 km in the outer parts of the belt, and it reduces to 5 km in the internal Alps. Nine additional temporary stations located ~40 km to the north and south of the main profile complement the permanent broadband networks to improve the 3-D constraints on the deep structures. Stations are equipped with Nanometrics Taurus data acquisition systems, and Trillium 120P/A, CMG3-ESP or CMG40T broadband sensors. The array was installed in the summer of 2012 and will be operated at least to April 2013. Because our schedule was tight, we had to achieve site selections in only 3-4 months in spite of strong constraints on site location related to short interstation spacing. Most sites are located in basements of buildings for security reasons and mains power supply. As most sensors are true broadband (90s or 120s), we put much effort on vault design to insure good thermal insulation and low noise at long periods. The vaults also had to be easily and rapidly built and they should be easily and totally removed at the end of the experiment. We used the PQLX software for quality control of our sites and vault design. The performances of our vaults are good for the vertical component with noise levels at 100s period in the range -185 dB (low noise model) to -165 dB. They are less good for horizontal components (noise level close to high noise model at periods > 20s) due to atmospheric pressure and temperature variations. Stations located outside buildings do not have better performances at 100s than stations located in basements. Two of our six stations installed outside buildings are prone to mass centering problems due to tilting of the concrete slab in soft soil. For state-of-health control and data transmission, we are testing 2G and 3G communication modems at 4 remote stations but with limited success. Database preparation and management benefitted from the expertise of engineers of the seismic datacenter of ISTerre. The experience gained on all technical aspects of a temporary experiment will provide valuable input for the preparation of the future AlpArray project.

Seismic noise study for a new seismic station at King Fahd University of Petroleum and Minerals in Saudi Arabia

NASA Astrophysics Data System (ADS)

Kaka, S. I.

2012-04-01

We have carried out a seismic noise study in order to understand the noise level at three selected locations at King Fahd University of Petroleum and Minerals (KFUPM), Dhahran, Saudi Arabia. The main purpose is to select a suitable site with low seismic noise and good signal-to-noise ratio for our new broadband seismic station. There are several factors involved in the selection of a site location for a new station. Most importantly, we need to strike a balance between a logistically convenient site versus a technically suitable site. As a starting point, we selected six potential sites due to accessibility and proximity to the seismic processing center laboratory in the Department of Earth Sciences (ESD) at KFUPM. We then eliminated two sites that are relatively close to possible low-frequency noise sources. We have considered many possible noise sources which include: vehicle traffic / heavy machinery, the direct path of air flowing from air conditioning vent, tall trees / power poles and metal doorways. One more site was eliminated because the site was located in the open where it experiences maximum wind speed which is considered a major source of noise. All three potential sites are situated within the Dammam Dome where both lower middle and upper Rus Formations are exposed. The upper Rus is mainly made up of fine grained chalky limestone and the lower Rus is made up of alternation of marls and thin dolomitic limestone. The area is not known for any major faults and considered very low seismicity and hence the identification of seismoteconic features is not required. Before conducting the noise study, we calibrated and tested the seismic recording system, which was recently acquired by the ESD at KFUPM. The system includes a seismic recorder and a sensor with a GPS device. We deployed the system in order to measure the low-frequency background noise. Knowing the low frequency noise will help in predicting the high-frequency noise. The recording systems were deployed for twenty eight days (based on the memory available with the recorder) continuously collecting data at all three potential sites. This continuous data collection was done as part of a larger study where microtremor measurements were made to better understand and characterize the origin of various near-surface noises over a non-producing reservoir in Dhahran, Saudi Arabia (Papoola and Kaka, 2011). The new station at KFUPM will be equipped with a 3-component 120s to 50Hz Trillium120 broad band seismometer, Taurus 24-bit data acquisition system along with a large LCD to display the waveform data in real-time. The KFUPM community will have an opportunity to observe daily seismic activity in real-time and to monitor/record both regional and teleseismic events. Moreover, students will gain the opportunity to identify P, S, Love, and Rayleigh waves and learn how to locate an earthquake. The station will also play an important role in providing a source of information about seismic activity for the general public. The new station is expected to be operational in a few months time.

Improvements of the Regional Seismic network of Northwestern Italy in the framework of ALCoTra program activities

NASA Astrophysics Data System (ADS)

Bosco, Fabrizio

2014-05-01

Arpa Piemonte (Regional Agency for Environmental Protection), in partnership with University of Genoa, manages the regional seismic network, which is part of the Regional Seismic network of Northwestern Italy (RSNI). The network operates since the 80s and, over the years, it has developed in technological features, analysis procedures and geographical coverage. In particular in recent years the network has been further enhanced through the integration of Swiss and French stations installed in the cross-border area. The environmental context enables the installation of sensors in sites with good conditions as regards ambient noise and limited local amplification effects (as proved by PSD analysis, signal quality monitoring via PQLX, H/V analysis). The instrumental equipment consists of Broadband and Very Broadband sensors (Nanometrics Trillium 40" and 240") and different technological solutions for signals real-time transmission (cable, satellite, GPRS), according to the different local environment, with redundant connections and with experimental innovative systems. Digital transmission and acquisition systems operate through standard protocols (Nanometrics, SeedLink), with redundancy in data centers (Genoa, Turin, Rome). Both real-time automatic and manual operational procedures are in use for signals analysis (events detection, picking, focal parameters and ground shaking determination). In the framework of cross-border cooperation program ALCoTra (http://www.interreg-alcotra.org), approved by the European Commission, several projects have been developed to improve the performances of seismic monitoring systems used by partners (Arpa Piemonte, Aosta Valley Region, CNRS, Joseph Fourier University). The cross-border context points out first of all the importance of signals sharing (from 14 to 23 stations in narrow French-Italian border area, with an increase of over 50%) and of coordination during new stations planning and installation in the area. In the ongoing ALCoTra project "CASSAT" (Coordination and Analysis of Alpine Trans-border Seismic Surveillance), we evaluate the improvement of monitoring systems performances in terms of localizations precision and number of detections. Furthermore, we update the procedures for the production of ground shaking maps, with installation of accelerometers and integration of new available data for site effects assessment (VS30 map, FA-VS30 correlations by numerical simulations of seismic response), determined for the specific regional context from geophysical surveys data and geological analysis. As a consequence of the increase of available data due to new stations installation and recently recorded events, a new local magnitude scaling law is calibrated for the area. We also develop a parametric methodology to improve network real-time localization procedures in Northwestern Italy. The area, surrounded by Western Alps and Northern Apennines, presents a complex system of lithospheric structures, characterized by strong heterogeneities of various physical parameters (Ivrea Body, subducting European lithosphere, Ligurian Sea Moho, Po Valley deposits). We work with a localization algorithm (Hypoinverse-2000) suitable for such a heterogeneous context , adopting multi-1d crustal velocities models, linked to epicentral coordinates. In this analysis, first we build velocities models integrating several available geophysical and geo-structural data; then we test jointly both models and algorithm parameters with specifically developed automatic iterative procedures, through batch scripting, database, GIS and statistical analysis tools.

The Irpinia Seismic Network (ISN): a new Monitoring Infrastructure for Seismic Alert Management in Campania Region, Southern Italy

NASA Astrophysics Data System (ADS)

Iannaccone, G.; Satriano, C.; Weber, E.; Cantore, L.; Corciulo, M.; Romano, L.; Martino, C.; Dicrosta, M.; Zollo, A.

2005-12-01

The Irpinia Seismic Network is an high dynamics, high density seismographic network under development in the Southern Apenninic chain. It is deployed in the area stroken by several destructive earthquakes during last centuries. In its final configuration the network will consist of more than fourty high dynamic seismic stations subdivided in physical subnetworks inter-connected by a robust data transmission system. The system is being designed with two primary targets: -Monitoring and analysis of background seismic activity produced by the active fault system which is the cause for large earthquakes in the past, included the 1980, Irpinia earthquake (Ms=6.9) - Development and experimentation of a prototype system for seismic early and post-event warning to be used for protecting public infrastructures and buildings of strategic relevance of the Regione Campania The seismic network will be completed in two stages: 1 - Deployment of 30 seismic stations along the Campania-Lucania Apenninic chain (to date almost completed) 2 - Setting up radio communication system for data transmission. Installation of 12 additional seismic stations (end of year 2006) To ensure an high dynamic recording range each site is equipped with two type of sensors: 30 force-balance accelerometer (model Guralp CMG5-T) and a velocimeter. In particular, 25 sites with short period three components instrument (model Geotech S13-J) and 5 with broad-band sensor (Nanometrics Trillium, with frequency response in the 0.033-50 Hz band). The used data logger is the Osiris-6 model produced by Agecodagis whose main features are: six channels, O/N 24 bit A/D converter, ARM processor with embedded Linux and open source software, two PCMCIA slots (used for two 5GB microdrive or one disk and wi-fi card), Ethernet, wi-fi and serial communication, low power cosumption (~1 W). Power is ensured by two 120 W solar panels and two 130 Ah gel batteries. Each recording site is equipped with a control/alarm system through a Programmable Logic Controller-GSM modem connected to several ambient sensors (forcing, battery control, fire, temperature) to remotely control the site status. Data are locally stored on the 5GB disk and continuously transmitted by the SeedLink protocol through a point-to-point wireless LAN bridge to interconnection nodes (Local Control Center, LCC). At LCC sites an Earthworm system runs on a dedicated computer to manage the data stream acquired by stations directly connected to LCC. The real time analysis system performs event detection and location based on triggers coming from data loggers and parametric information provided by the other LCCs. At present, data transmission among LCC is performed via commercial ADSL. Once an event is detected and located, the system performs automatic magnitude and focal mechanism estimation. The results of this analysis are used to build a local event Data Base (DB) and, at the same time, they are sent to other LCC and to the network operating room located in Naples (RISSC). At RISSC center the network data are managed by a system gathering parametric data from all the LCC and performing real time analysis based on which it is decided whether or not issuing a seismic alert. Future plans for network operation involve the installation of additional 12 stations, and the upgrading of data transmission system to a proprietary radio link with SDH technology. The project is financial supported by the Campania Regional Department of Civil Protection.