Direct Printing of Organic Electronics at the Nanometer Scale

DTIC Science & Technology

2006-02-01

patterning as seen in Figure 3. Also, a flat film OVJP grown Alq3 NPD OLED was shown to be competitive with VTE with quantum efficiencies of 0.84%. 0 0...a tris(8-hydroxyquinoline)- aluminum ( Alq3 ) electron transport and emitting layer. The OLEDs exhibited an external 8 quantum efficiency of (0.84...parameter analyzer and a Newport Model 2932-C dual-channel power meter. An OLED having the layer structure: ITO/60nm NPD/60nm Alq3 /LiF:Al was deposited

Erbium Doped Quantum Dot and Si:O and Plasmon Resonance Enabled Quantum Dot Nanoscale Lasers

DTIC Science & Technology

2009-08-31

electroluminescence has to be coupled with a high-Q cavity for lasing. Alq3 PEDOT:PSS ITO — • MEHPPV +PbSe QDs . • •A iz^————— Gold (Au...PEDOT:PSS on the ITO anode and Alq3 /Ca/Al cathode. The inset is a SEM image of the L3 defect photonic crystal microcavity in silicon. Outer air holes at...consisting of tris(8-hydroxyquinoline)aluminum ( Alq3 ), calcium, and aluminum. The device heterostructure is schematically shown in Fig. 5(a). The ITO

A Molecular Beam Deposition of DNA Nanometer Films

DTIC Science & Technology

2007-01-01

device structure consists of ITO/PEDOT:PSS (50 nm)/NPB (30 nm)/ Alq3 (40 nm)/BCP (20 nm)/ Alq3 (10 nm)/Li:Al, while the Bi- OLED has an additional DNA...layer; DNA- CTMA is an electron blocking layer (EBL); NPB is used as hole transport layer; Alq3 is used for both the electron transport layer and the...N,N’-bis(naphthalen-1-yl)-N,N’- bis(phenyl)benzidine)], Alq3 [tris-(8-hydroxyquinoline) aluminum] and BCP [2,9- Dimethyl-4,7-diphenyl-1,10

Effects of morphological control on the characteristics of vertical-type OTFTs using Alq3.

PubMed

Kim, Young Do; Park, Jong Wook; Kang, In Nam; Oh, Se Young

2008-09-01

We have fabricated vertical-type organic thin-film transistors (OTFTs) using tris-(8-hydroxyquinoline) aluminum (Alq(3)) as an n-type active material. Vertical-type OTFT using Alq(3) has a layered structure of Al(source electrode)/Alq(3)(active layer)/Al(gate electrode)/Alq(3)(active layer)/ITO glass(drain electrode). Alq(3) thin films containing various surface morphologies could be obtained by the control of evaporation rate and substrate temperature. The effects of the morphological control of Alq(3) thin layer on the grain size and the flatness of film surface were investigated. The characteristics of vertical-type OTFT significantly influenced the growth condition of Alq(3) layer.

Structure of Co-Doped Alq3 thin films investigated by grazing incidence X-ray absorption fine structure and Fourier transform infrared spectroscopy.

PubMed

Lin, Liang; Pang, Zhiyong; Fang, Shaojie; Wang, Fenggong; Song, Shumei; Huang, Yuying; Wei, Xiangjun; Yu, Haisheng; Han, Shenghao

2011-02-10

The structural properties of Co-doped tris(8-hydroxyquinoline)aluminum (Alq(3)) have been studied by grazing incidence X-ray absorption fine structure (GIXAFS) and Fourier transform infrared spectroscopy (FTIR). GIXAFS analysis suggests that there are multivalent Co-Alq(3) complexes and the doped Co atoms tend to locate at the attraction center with respect to N and O atoms and bond with them. The FTIR spectra indicate that the Co atoms interact with the meridional (mer) isomer of Alq(3) rather than forming inorganic compounds.

Control of Alq3 wetting layer thickness via substrate surface functionalization.

PubMed

Tsoi, Shufen; Szeto, Bryan; Fleischauer, Michael D; Veinot, Jonathan G C; Brett, Michael J

2007-06-05

The effects of substrate surface energy and vapor deposition rate on the initial growth of porous columnar tris(8-hydroxyquinoline)aluminum (Alq3) nanostructures were investigated. Alq3 nanostructures thermally evaporated onto as-supplied Si substrates bearing an oxide were observed to form a solid wetting layer, likely caused by an interfacial energy mismatch between the substrate and Alq3. Wetting layer thickness control is important for potential optoelectronic applications. A dramatic decrease in wetting layer thickness was achieved by depositing Alq3 onto alkyltrichlorosilane-derivatized Si/oxide substrates. Similar effects were noted with increasing deposition rates. These two effects enable tailoring of the wetting layer thickness.

Surface morphology and interdiffusion of LiF in Alq3-based organic light-emitting devices.

PubMed

Lee, Young Joo; Li, Xiaolong; Kang, Da-Yeon; Park, Seong-Sik; Kim, Jinwoo; Choi, Jeong-Woo; Kim, Hyunjung

2008-09-01

Highly efficient organic light-emitting devices (OLEDs) have been realized by insertion of a thin insulating lithium fluoride (LiF) layer between aluminum (Al) cathode and an electron transport layer, tris-(8-hydroxyquinoline) aluminum (Alq(3)). In this paper, we study the surface morphology of LiF on Alq(3) by synchrotron X-ray scattering and atomic force microscopy (AFM) as a function of thickness of LiF. We also study the interdiffusion of LiF into Al cathode as well as into Alq(3) layer as a function of temperature. Initially, LiF molecules are distributed randomly as clusters on the Alq(3) layer and then gradually form a layer as increasing LiF thickness. The interdiffusion of LiF into Al occurs more actively than into Alq(3) in annealing process. LiF on Alq(3) induces the ordering of Al to (111) direction strongly with increasing LiF thickness.

Effect of thermal annealing on the structural and optical properties of tris-(8-hydroxyquinoline)aluminum(III) (Alq3 ) films.

PubMed

Cuba, M; Muralidharan, G

2015-05-01

Tris-(8-hydroxyquionoline)aluminum (Alq3 ) was synthesized and coated on to a glass substrate using the dip coating method. The structural and optical properties of the Alq3 film after thermal annealing from 50°C to 300°C in 50° steps was studied. The films have been prepared with 2 to 16 layers (42-324 nm). The thickness and thermal annealing of Alq3 films were optimized for maximum luminescence yield. The Fourier transform infrared spectrum confirms the formation of quinoline with absorption in the region 700 - 500/cm. Partial sublimation and decomposition of quinoline ion was observed with the Alq3 films annealed at 300°C. The X-ray diffraction pattern of the Alq3 film annealed at 50°C to 150°C reveals the amorphous nature of the films. The Alq3 film annealed above 150°C were crystalline nature. Film annealed at 150°C exhibits a photoluminescence intensity maximum at 512 nm when excited at 390 nm. The Alq3 thin film deposited with 10 layers (220 nm) at 150°C exhibited maximum luminescence yield. Copyright © 2014 John Wiley & Sons, Ltd.

Highly sensitive heavy metal ion detection using AlQ3 microwire functionalized QCM

NASA Astrophysics Data System (ADS)

Can, Nursel; Aǧar, Meltem; Altındal, Ahmet

2016-03-01

Tris(8-hydroxyquinoline) aluminum (Alq3) microwires was successfully synthesized for the fabrication of Alq3 microwires-coated QCM sensors to detect the heavy metal ions in aqueous solution. AT-cut quartz crystal microbalance (QCM) of 10 MHz fundamental resonance frequency having gold electrodes were used as transducers. Typical measuring cycle consisted of repeated flow of target measurands through the flow cell and subsequent washing to return the baseline. The QCM results indicated that the Alq3 microwires exhibit excellent sensitivity, stability and short response-recovery time, which are much attractive for the development of portable and highly sensitive heavy metal ion sensors in water samples.

Improved luminescence intensity and stability of thermal annealed ZnO incorporated Alq3 composite films.

PubMed

Cuba, M; Muralidharan, G

2015-11-01

The 30 wt% of ZnO (weight percentage of ZnO has been optimised) incorporated tris- (8-hydroxyquinoline)aluminum (Alq3) has been synthesised and coated on to glass substrates using dip coating method. The structural and optical properties of the Alq3/ZnO composite film after thermal annealing from 50 to 300 °C insteps 50° has been studied and reported. XRD pattern reveals the presence of crystalline ZnO in all the annealed films. The films annealed above 150 °C reveal the presence of crystalline Alq3 along with crystalline ZnO. The FTIR spectra confirm the presence of hydroxyquinoline and ZnO vibration in all the annealed composite films. The composite films annealed above 150 °C show a partial sublimation and degradation of hydroxyquinoline compounds. The ZnO incorporated composite films (Alq3/ZnO) exhibit two emission peaks, one corresponding to ZnO at 487 nm and another at 513 nm due to Alq3. The films annealed at 200 °C exhibit maximum photoluminescence (PL) intensity than pristine film at 513 nm when excited at 390 nm.

Insights Into the Solution Crystallization of Oriented Alq3 and Znq2 Microprisms and Nanorods.

PubMed

Boulet, Joel; Mohammadpour, Arash; Shankar, Karthik

2015-09-01

Optimized solution-based methods to grow high quality micro- and nanocrystals of organic semi-conductors with defined size, shape and orientation are important to a variety of optoelectronic applications. In this context, we report the growth of single crystal micro- and nanostructures of the organic semiconductors Tris(8-hydroxyquinoline)aluminum (Alq3) and bis(8-hydroxyquinoline)zinc (Znq2) terminating in flat crystal planes using a combination of evaporative and antisolvent crystallization. By controlling substrate-specific nucleation and optimizing the conditions of growth, we generate vertically-oriented hexagonal prism arrays of Alq3, and vertical half-disks and sharp-edged rectangular prisms of Znq2. The effect of process variables such as ambient vapour pressure, choice of anti-solvent and temperature on the morphology and crystal habit of the nanostructures were studied and the results of varying them catalogued to gain a better understanding of the mechanism of growth.

High performance organic ultraviolet photodetectors based on m-MTDATA

NASA Astrophysics Data System (ADS)

Zhao, Zhongli; Bai, Xiaofeng; Shang, Yubin; Yang, Jikai; Li, Baozeng; Song, De

2018-02-01

We demonstrate highly efficient organic ultraviolet photodetectors using 4,4',4'' -tris[3-methyl-pheny(phenyl) amino] triphenylamine (m-MTDATA) and aluminum Tris(8-Hydroxyquinolinate) Synonym Alq3). The optimized photodetector delivers a photocurrent of 1.40 mA/cm2 at10 V, corresponding to a response of 127 mA/W under an illumination of 375 nm UV light irradiation with an intensity of 10.5 mW/cm2 and a detectivity of 2.15×1011 cm Hz1/2 /W. The high response is attributed to the larger band offset at m-MTDATA/ Alq3 heterojunction, the suppression of radiative decay of m-MTDATA and efficient electron transfer from m-MTDATA to Alq3. The working mechanism of harvesting high performance is also discussed in detail.

The importance of holes in aluminium tris-8-hydroxyquinoline (Alq{sub 3}) devices with Fe and NiFe contacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Hongtao; Desai, P.; Kreouzis, T.

To study the dominant charge carrier polarity in aluminium tris-8-hydroxyquinoline (Alq{sub 3}) based spin valves, single Alq{sub 3} layer devices with NiFe, ITO, Fe, and aluminium electrodes were fabricated and characterised by Time of Flight (ToF) and Dark Injection (DI) techniques, yielding a lower hole mobility compared to electron mobility. We compare the mobility measured by DI for the dominant carrier injected from NiFe and Fe electrodes into Alq{sub 3}, to that of holes measured by ToF. This comparison leads us to conclude that the dominant charge carriers in Alq{sub 3} based spin valves with NiFe or Fe electrodes aremore » holes.« less

The structure of the blue luminescent delta-phase of tris(8-hydroxyquinoline)aluminium(III) (Alq3).

PubMed

Cölle, Michael; Dinnebier, Robert E; Brütting, Wolfgang

2002-12-07

The existence of the facial isomer in the delta-phase of Alq3 is proven by X-ray structural analysis, revealing that both the different molecular structure and the weaker overlap of the pi-orbitals of hydroxyquinoline ligands belonging to neighboring Alq3 molecules as compared to other phases (alpha, beta) are likely to be the origin of the significantly different optical properties of delta-Alq3.

Significant relaxation of residual negative carrier in polar Alq3 film directly detected by high-sensitivity photoemission

NASA Astrophysics Data System (ADS)

Kinjo, Hiroumi; Lim, Hyunsoo; Sato, Tomoya; Noguchi, Yutaka; Nakayama, Yasuo; Ishii, Hisao

2016-02-01

Tris(8-hydroxyquinoline)aluminum (Alq3) has been widely applied as a good electron-injecting layer (EIL) in organic light-emitting diodes. High-sensitivity photoemission measurement revealed a clear photoemission by visible light, although its ionization energy is 5.7 eV. This unusual photoemission is ascribed to Alq3 anions captured by positive polarization charges. The observed electron detachment energy of the anion was about 1 eV larger than the electron affinity reported by inverse photoemission. This difference suggests that the injected electron in the Alq3 layer is energetically relaxed, leading to the reduction in injection barrier. This nature is one of the reasons why Alq3 worked well as the EIL.

Conformal and highly luminescent monolayers of Alq3 prepared by gas-phase molecular layer deposition.

PubMed

Räupke, André; Albrecht, Fabian; Maibach, Julia; Behrendt, Andreas; Polywka, Andreas; Heiderhoff, Ralf; Helzel, Jonatan; Rabe, Torsten; Johannes, Hans-Hermann; Kowalsky, Wolfgang; Mankel, Eric; Mayer, Thomas; Görrn, Patrick; Riedl, Thomas

2014-01-22

The gas-phase molecular layer deposition (MLD) of conformal and highly luminescent monolayers of tris(8-hydroxyquinolinato)aluminum (Alq3) is reported. The controlled formation of Alq3 monolayers is achieved for the first time by functionalization of the substrate with amino groups, which serve as initial docking sites for trimethyl aluminum (TMA) molecules binding datively to the amine. Thereby, upon exposure to 8-hydroxyquinoline (8-HQ), the self-limiting formation of highly luminescent Alq3 monolayers is afforded. The growth process and monolayer formation were studied and verified by in situ quartz crystal monitoring, optical emission and absorption spectroscopy, and X-ray photoelectron spectroscopy. The nature of the MLD process provides an avenue to coat arbitrarily shaped 3D surfaces and porous structures with high surface areas, as demonstrated in this work for silica aerogels. The concept presented here paves the way to highly sensitive luminescent sensors and dye-sensitized metal oxides for future applications (e.g., in photocatalysis and solar cells).

Electronic structure and magnetism in transition metals doped 8-hydroxy-quinoline aluminum.

PubMed

Baik, Jeong Min; Shon, Yoon; Lee, Seung Joo; Jeong, Yoon Hee; Kang, Tae Won; Lee, Jong-Lam

2008-10-15

We report the room-temperature ferromagnetism in transition metals (Co, Ni)-doped 8-hydroxy-quinoline aluminum (Alq3) by thermal coevaporation of high purity metal and Alq3 powders. For 5% Co-doped Alq3, a maximum magnetization of approximately 0.33 microB/Co at 10 K was obtained and ferromagnetic behavior was observed up to 300 K. The Co atoms interact chemically with O atoms and provide electrons to Alq3, forming new states acting as electron trap sites. From this, it is suggested that ferromagnetism may be associated with the strong chemical interaction of Co atoms and Alq3 molecules.

Tuning open-circuit voltage in organic solar cells by magnesium modified Alq3

PubMed Central

Chou, Chi-Ta; Lin, Chien-Hung; Wu, Meng-Hsiu; Cheng, Tzu-Wei; Lee, Jiun-Haw; Liu, Chin-Hsin J.; Tai, Yian; Chattopadhyay, Surojit; Wang, Juen-Kai; Chen, Kuei-Hsien; Chen, Li-Chyong

2011-01-01

The low molecular weight tris-(8-hydroxyquinoline) aluminum (Alq3) has been incorporated with magnesium (Mg) that altered the nature of its opto-electronic characteristics. The lowering of the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) in Mg:Alq3, compared to pure Alq3, creates a stronger field (exceeding the exciton binding energy) at the donor-acceptor junction to dissociate the photo-generated exciton and also provides a low barrier for electron transport across the device. In an electron-only device (described in the text), a current enhancement in excess of 103, with respect to pure Alq3, could be observed at 10 V applied bias. Optimized Mg:Alq3 layer, when introduced in the photovoltaic device, improves the power conversion efficiencies significantly to 0.15% compared to the pure Alq3 device. The improvement in the photovoltaic performance has been attributed to the superior exciton dissociation and carrier transport. PMID:22087050

Chemical failure modes of AlQ3-based OLEDs: AlQ3 hydrolysis.

PubMed

Knox, John E; Halls, Mathew D; Hratchian, Hrant P; Schlegel, H Bernhard

2006-03-28

Tris(8-hydroxyquinoline)aluminum(III), AlQ3, is used in organic light-emitting diodes (OLEDs) as an electron-transport material and emitting layer. The reaction of AlQ3 with trace H2O has been implicated as a major failure pathway for AlQ3-based OLEDs. Hybrid density functional calculations have been carried out to characterize the hydrolysis of AlQ3. The thermochemical and atomistic details for this important reaction are reported for both the neutral and oxidized AlQ3/AlQ3+ systems. In support of experimental conclusions, the neutral hydrolysis reaction pathway is found to be a thermally activated process, having a classical barrier height of 24.2 kcal mol(-1). First-principles infrared and electronic absorption spectra are compared to further characterize AlQ3 and the hydrolysis pathway product, AlQ2OH. The activation energy for the cationic AlQ3 hydrolysis pathway is found to be 8.5 kcal mol(-1) lower than for the neutral reaction, which is significant since it suggests a role for charge imbalance in promoting chemical failure modes in OLED devices.

Write once read many memory device from Tris-8 (-hydroxyquinoline) aluminum and Indium tin oxide nano particles

NASA Astrophysics Data System (ADS)

Aneesh, J.; Predeep, P.

2011-10-01

Consequent to the fast increase in data storage requirements new materials and device structures are explored in a war footing. Organic memory devices are attracting lot of interest among the researchers and are becoming a hot topic of investigations. This study is an attempt to develop a tri-layer organic memory device using indium tin oxide (ITO) nanoparticles as charge trapping middle layer between tris-8(-hydroxyquinoline)aluminum (Alq3) layers employing spin coating technique. Device switching is studied by applying a current-voltage (I-V) sweep. On increasing the applied bias the device switched from the initial high resistance (OFF) state to a low resistance (ON) state at a switch on voltage of around 4 V. ON/OFF ratio is of the order of 100 at a read voltage of 2 V. The device is found to remain in the low resistance state on further scans, showing the applicability of this device as a write once read many times (WORM) memory.

Generation and decay dynamics of triplet excitons in Alq3 thin films under high-density excitation conditions.

PubMed

Watanabe, Sadayuki; Furube, Akihiro; Katoh, Ryuzi

2006-08-31

We studied the generation and decay dynamics of triplet excitons in tris-(8-hydroxyquinoline) aluminum (Alq3) thin films by using transient absorption spectroscopy. Absorption spectra of both singlet and triplet excitons in the film were identified by comparison with transient absorption spectra of the ligand molecule (8-hydroxyquinoline) itself and the excited triplet state in solution previously reported. By measuring the excitation light intensity dependence of the absorption, we found that exciton annihilation dominated under high-density excitation conditions. Annihilation rate constants were estimated to be gammaSS = (6 +/- 3) x 10(-11) cm3 s(-1) for single excitons and gammaTT = (4 +/- 2) x 10(-13) cm3 s(-1) for triplet excitons. From detailed analysis of the light intensity dependence of the quantum yield of triplet excitons under high-density conditions, triplet excitons were mainly generated through fission from highly excited singlet states populated by singlet-singlet exciton annihilation. We estimated that 30% of the highly excited states underwent fission.

Intrinsic mobility limit for anisotropic electron transport in Alq3.

PubMed

Drew, A J; Pratt, F L; Hoppler, J; Schulz, L; Malik-Kumar, V; Morley, N A; Desai, P; Shakya, P; Kreouzis, T; Gillin, W P; Kim, K W; Dubroka, A; Scheuermann, R

2008-03-21

Muon spin relaxation has been used to probe the charge carrier motion in the molecular conductor Alq3 (tris[8-hydroxy-quinoline] aluminum). At 290 K, the magnetic field dependence of the muon spin relaxation corresponds to that expected for highly anisotropic intermolecular electron hopping. Intermolecular mobility in the fast hopping direction has been found to be 0.23+/-0.03 cm2 V-1 s(-1) in the absence of an electric- field gradient, increasing to 0.32+/-0.06 cm2 V-1 s(-1) in an electric field gradient of 1 MV m(-1). These intrinsic mobility values provide an estimate of the upper limit for mobility achievable in bulk material.

Control of resonant wavelength from organic light-emitting materials by use of a Fabry-Perot microcavity structure.

PubMed

Jung, Boo Young; Kim, Nam Young; Lee, Changhee; Hwangbo, Chang Kwon; Seoul, Chang

2002-06-01

We report the fabrication of Fabry-Perot microcavity structures with the organic light-emitting material tris-(8-hydroxyquinoline) aluminum (Alq3) and derive their optical properties by measuring their photoluminescence (PL) and absorption. Silver and a TiO2-SiO2 multilayer were used as metal and dielectric reflectors, respectively, in a Fabry-Perot microcavity structure. Three types of microcavity were prepared: type A consisted of [air[Ag[Alq3]Ag]glass]; type B, of [air[dielectric[Alq3]dielectric]glass]; and type C, of [air[Ag[Alq2]dielectric]glass]. A bare Alq3 film of [air[Alq3]glass] had its PL peak near 514 nm, and its full width at half-maximum (FWHM) was 80 nm. The broad FWHM of a bare Alq3 film was reduced to 15-27.5, 7-10.5, and 16-16.6 nm for microcavity types A, B, and C, respectively. Also, we could control the PL peak of the microcavity structure by changing the spacer thickness, the amount of phase change on reflection, and the angle of incidence.

Simulation of mixed-host emitting layer based organic light emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riku, C.; Kee, Y. Y.; Ong, T. S.

2015-04-24

‘SimOLED’ simulator is used in this work to investigate the efficiency of the mixed-host organic light emitting devices (MH-OLEDs). Tris-(8-hydroxyquinoline) aluminum(3) (Alq{sub 3}) and N,N-diphenyl-N,N-Bis(3-methylphenyl)-1,1-diphenyl-4,4-diamine (TPD) are used as the electron transport layer (ETL) material and hole transport layer (HTL) material respectively, and the indium-doped tin oxide (ITO) and aluminum (Al) as anode and cathode. Three MH-OLEDs, A, B and C with the same structure of ITO / HTM (15 nm) / Mixed host (70 nm) / ETM (10 nm) /Al, are stimulated with ratios TPD:Alq{sub 3} of 3:5, 5:5, and 5:3 respectively. The Poole-Frenkel model for electron and hole mobilities is employedmore » to compute the current density-applied voltage-luminance characteristics, distribution of the electric field, carrier concentrations and recombination rate.« less

Photoluminescence of Alq3 - and Tb-activated aluminium-tris(8-hydroxyquinoline) complex for blue chip-excited OLEDs.

PubMed

Yawalkar, P W; Dhoble, S J; Thejo Kalyani, N; Atram, R G; Kokode, N S

2013-01-01

The tris(8-hydroxyquinoline)-aluminium complex is the most important and widely studied as electron transporting and green light emitting material. Alq(3) and Tb(x) Al((1-x)) q(3) have been synthesized (where x = 0.1, 0.3, 0.5, 0.7 and 0.9) and blended films of Alq(3) and Tb(x) Al((1-x)) q(3) with PMMA and PS at different percentage weight (wt%) concentrations (e.g., 0.1, 1, 5, 10, 25 and 50 wt%) have been prepared. The synthesized materials and their blended thin films have been characterized by a photoluminescence (PL) technique; the synthesis and PL characterization are reported in this paper. The synthesized metal complex shows bright emission of green light with blue light excitation (440 nm) and the prepared Tb(x) Al((1-x)) q(3) phosphor may be applicable in blue chip-excited OLEDs for the newly developed wallpaper lighting technology. Copyright © 2012 John Wiley & Sons, Ltd.

Organic bistable memory devices based on MoO3 nanoparticle embedded Alq3 structures.

PubMed

Abhijith, T; Kumar, T V Arun; Reddy, V S

2017-03-03

Organic bistable memory devices were fabricated by embedding a thin layer of molybdenum trioxide (MoO 3 ) between two tris-(8-hydroxyquinoline)aluminum (Alq 3 ) layers. The device exhibited excellent switching characteristics with an ON/OFF current ratio of 1.15 × 10 3 at a read voltage of 1 V. The device showed repeatable write-erase capability and good stability in both the conductance states. These conductance states are non-volatile in nature and can be obtained by applying appropriate voltage pulses. The effect of MoO 3 layer thickness and its location in the Alq 3 matrix on characteristics of the memory device was investigated. The field emission scanning electron microscopy (FE-SEM) images of the MoO 3 layer revealed the presence of isolated nanoparticles. Based on the experimental results, a mechanism has been proposed for explaining the conductance switching of fabricated devices.

Organic bistable memory devices based on MoO3 nanoparticle embedded Alq3 structures

NASA Astrophysics Data System (ADS)

Abhijith, T.; Kumar, T. V. Arun; Reddy, V. S.

2017-03-01

Organic bistable memory devices were fabricated by embedding a thin layer of molybdenum trioxide (MoO3) between two tris-(8-hydroxyquinoline)aluminum (Alq3) layers. The device exhibited excellent switching characteristics with an ON/OFF current ratio of 1.15 × 103 at a read voltage of 1 V. The device showed repeatable write-erase capability and good stability in both the conductance states. These conductance states are non-volatile in nature and can be obtained by applying appropriate voltage pulses. The effect of MoO3 layer thickness and its location in the Alq3 matrix on characteristics of the memory device was investigated. The field emission scanning electron microscopy (FE-SEM) images of the MoO3 layer revealed the presence of isolated nanoparticles. Based on the experimental results, a mechanism has been proposed for explaining the conductance switching of fabricated devices.

Improved electron injection in spin coated Alq3 incorporated ZnO thin film in the device for solution processed OLEDs

NASA Astrophysics Data System (ADS)

Dasi, Gnyaneshwar; Ramarajan, R.; Thangaraju, Kuppusamy

2018-04-01

We deposit tris-(8-hydroxyquinoline)aluminum (Alq3) incorporated zinc oxide (ZnO) thin films by spin coating method under the normal ambient. It showed the higher transmittance (90% at 550 nm) when compared to that (80% at 550 nm) of spin coated pure ZnO film. SEM studies show that the Alq3 incorporation in ZnO film also enhances the formation of small sized particles arranged in the network of wrinkles on the surface. XRD reveals the improved crystalline properties upon Alq3 inclusion. We fabricate the electron-only devices (EODs) with the structure of ITO/spin coated ZnO:Alq3 as ETL/Alq3 interlayer/LiF/Al. The device showed the higher electron current density of 2.75 mA/cm2 at 12V when compared to that (0.82 mA/cm2 at 12V) of the device using pure ZnO ETL. The device results show that it will be useful to fabricate the low-cost solution processed OLEDs for future lighting and display applications.

Facile solution synthesis of hexagonal Alq3 nanorods and their field emission properties.

PubMed

Hu, Jin-Song; Ji, Heng-Xing; Cao, An-Min; Huang, Zheng-Xi; Zhang, Yang; Wan, Li-Jun; Xia, An-Dong; Yu, Da-Peng; Meng, Xiang-Min; Lee, Shuit-Tong

2007-08-07

A facile self-assembly growth route assisted by surfactant has been developed to synthesize tris(8-hydroxyquinoline)aluminium (Alq(3)) nanorods with regular hexagonal shape and good crystallinity, which exhibit field-emission characteristics with a very low turn-on field of ca. 3.1 V microm(-1) and a high field-enhancement factor of ca. 1300.

Optically active charge transfer in hybrids of Alq3 nanoparticles and MoS2 monolayer

NASA Astrophysics Data System (ADS)

Ghimire, Ganesh; Dhakal, Krishna P.; Neupane, Guru P.; Jo, Seong Gi; Kim, Hyun; Seo, Changwon; Lee, Young Hee; Joo, Jinsoo; Kim, Jeongyong

2017-05-01

Organic/inorganic hybrid structures have been widely studied because of their enhanced physical and chemical properties. Monolayers of transition metal dichalcogenides (1L-TMDs) and organic nanoparticles can provide a hybridization configuration between zero- and two-dimensional systems with the advantages of convenient preparation and strong interface interaction. Here, we present such a hybrid system made by dispersing π-conjugated organic (tris (8-hydroxyquinoline) aluminum(III)) (Alq3) nanoparticles (NPs) on 1L-MoS2. Hybrids of Alq3 NP/1L-MoS2 exhibited a two-fold increase in the photoluminescence of Alq3 NPs on 1L-MoS2 and the n-doping effect of 1L-MoS2, and these spectral and electronic modifications were attributed to the charge transfer between Alq3 NPs and 1L-MoS2. Our results suggested that a hybrid of organic NPs/1L-TMD can offer a convenient platform to study the interface interactions between organic and inorganic nano objects and to engineer optoelectronic devices with enhanced performance.

Optically active charge transfer in hybrids of Alq3 nanoparticles and MoS2 monolayer.

PubMed

Ghimire, Ganesh; Dhakal, Krishna P; Neupane, Guru P; Gi Jo, Seong; Kim, Hyun; Seo, Changwon; Hee Lee, Young; Joo, Jinsoo; Kim, Jeongyong

2017-05-05

Organic/inorganic hybrid structures have been widely studied because of their enhanced physical and chemical properties. Monolayers of transition metal dichalcogenides (1L-TMDs) and organic nanoparticles can provide a hybridization configuration between zero- and two-dimensional systems with the advantages of convenient preparation and strong interface interaction. Here, we present such a hybrid system made by dispersing π-conjugated organic (tris (8-hydroxyquinoline) aluminum(III)) (Alq 3 ) nanoparticles (NPs) on 1L-MoS 2 . Hybrids of Alq 3 NP/1L-MoS 2 exhibited a two-fold increase in the photoluminescence of Alq 3 NPs on 1L-MoS 2 and the n-doping effect of 1L-MoS 2 , and these spectral and electronic modifications were attributed to the charge transfer between Alq 3 NPs and 1L-MoS 2 . Our results suggested that a hybrid of organic NPs/1L-TMD can offer a convenient platform to study the interface interactions between organic and inorganic nano objects and to engineer optoelectronic devices with enhanced performance.

Effects of interfacial stability between electron transporting layer and cathode on the degradation process of organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Chu, Ta-Ya; Lee, Yong-Han; Song, Ok-Keun

2007-11-01

The authors have demonstrated that the increase of electron injection barrier height between tris(8-hydroxyquinoline)aluminum (Alq3) and LiF /Al cathode is one of the most critical parameters to determine the reliability of organic light-emitting diode with the typical structure of indium tin oxide/N ,N'-bis(naphthalen-1-yl)-N ,N'-bis(phenyl) benzidine/Alq3/LiF /Al. The electrical properties of several devices (hole only, electron only, and integrated double-layered devices) have been measured in the function of operating time to analyze the bulk and interface property changes. Bulk properties of trap energy and mobility in an organic layer have been estimated by using trap-charge-limited currents and transient electroluminescence measurements.

Possible pore size effects on the state of tris(8-quinolinato)aluminum(III) (Alq3) adsorbed in mesoporous silicas and their temperature dependence.

PubMed

Tagaya, Motohiro; Ogawa, Makoto

2008-12-07

The states of tris(8-quinolinato)aluminum(III) (Alq3) adsorbed in mesoporous silicas with different pore sizes (2.5, 3.1 and 5.0 nm) were investigated. Alq3 was successfully occluded into the mesoporous silicas from solution and the adsorbed amount of Alq3 per BET surface area was effectively controlled by changing the added amount Alq3 to the solution. The state of Alq3 in the mesopore varied depending on the pore size as well as the adsorbed amount of Alq3 as revealed by variation of the photoluminescence spectra. The luminescence of the adsorbed Alq3 was found to be temperature-dependent, indicating the mobility of the adsorbed Alq3 to temperature variations. The temperature-dependence also depended on the pore size. The guest-guest interactions between Alq3 molecules as well as the host-guest interactions between Alq3 and the mesopore were controlled by the pore size.

[Multiplayer white organic light-emitting diodes with different order and thickness of emission layers].

PubMed

Xu, Wei; Lu, Fu-Han; Cao, Jin; Zhu, Wen-Qing; Jiang, Xue-Yin; Zhang, Zhi-Lin; Xu, Shao-Hong

2008-02-01

In multilayer OLED devices, the order and thickness of the emission layers have great effect on their spectrum. Based on the three basic colours of red, blue and green, a series of white organic light-emitting diodes(WOLEDS)with the structure of ITO/CuPc(12 nm)/NPB(50 nm)/EML/LiF(1 nm)/Al(100 nm) and a variety of emission layer's orders and thicknesses were fabricated. The blue emission material: 2-t-butyl-9,10-di-(2-naphthyl)anthracene (TBADN) doped with p-bis(p-N, N-diphenyl-amono-styryl)benzene(DSA-Ph), the green emission material: tris-[8-hydroxyquinoline]aluminum(Alq3) doped with C545, and the red emission material: tris-[8-hydroxyquinoline]aluminum( Alq3) doped with 4-(dicyanomethylene)-2-t-butyl-6-(1, 1, 7, 7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) were used. By adjusting the order and thickness of each emission layer in the RBG structure, we got a white OLED with current efficiency of 5.60 cd x A(-1) and Commission Internationale De L'Eclairage (CIE) coordinates of (0. 34, 0.34) at 200 mA x cm(-2). Its maximum luminance reached 20 700 cd x m(-2) at current density of 400 mA x cm(-2). The results were analyzed on the basis of the theory of excitons' generation and diffusion. According to the theory, an equation was set up which relates EL spectra to the luminance efficiency, the thickness of each layer and the exciton diffusion length. In addition, in RBG structure with different thickness of red layer, the ratio of th e spectral intensity of red to that of blue was calculated. It was found that the experimental results are in agreement with the theoretical values.

Combined optical gain and degradation measurements in DCM2 doped Tris-(8-hydroxyquinoline)aluminum thin-films

NASA Astrophysics Data System (ADS)

Čehovski, Marko; Döring, Sebastian; Rabe, Torsten; Caspary, Reinhard; Kowalsky, Wolfgang

2016-04-01

Organic laser sources offer the opportunity to integrate flexible and widely tunable lasers in polymer waveguide circuits, e.g. for Lab-on-Foil applications. Therefore, it is necessary to understand gain and degradation processes for long-term operation. In this paper we address the challenge of life-time (degradation) measurements of photoluminescence (PL) and optical gain in thin-film lasers. The well known guest-host system of aluminum-chelate Alq3 (Tris-(8-hydroxyquinoline)aluminum) as host material and the laser dye DCM2 (4-(Dicyanomethylene)-2- methyl-6-julolidyl-9-enyl-4H-pyran) as guest material is employed as laser active material. Sample layers have been built up by co-evaporation in an ultrahigh (UHV) vacuum chamber. 200nm thick films of Alq3:DCM2 with different doping concentrations have been processed onto glass and thermally oxidized silicon substrates. The gain measurements have been performed by the variable stripe length (VSL) method. This measurement technique allows to determine the thin-film waveguide gain and loss, respectively. For the measurements the samples were excited with UV irradiation (ƛ = 355nm) under nitrogen atmosphere by a passively Q-switched laser source. PL degradation measurements with regard to the optical gain have been done at laser threshold (approximately 3 μJ/cm2), five times above laser threshold and 10 times above laser threshold. A t50-PL lifetime of > 107 pulses could be measured at a maximum excitation energy density of 32 μJ/cm2. This allows for a detailed analysis of the gain degradation mechanism and therefore of the stimulated cross section. Depending on the DCM2 doping concentration C the stimulated cross section was reduced by 35 %. Nevertheless, the results emphasizes the necessity of the investigation of degradation processes in organic laser sources for long-term applications.

Spinterface between tris(8-hydroxyquinoline)metal(III) molecules and magnetic surfaces: a first-principles study

NASA Astrophysics Data System (ADS)

Jiang, W.; Wang, Jingying; Dougherty, Daniel; Liu, Feng; Feng Liu Team; Daniel Dougherty Team

Using first-principles calculations, we have systematically investigated the hybridization between tris(8-hydroxyquinoline)metal(III) (Mq3, M = Fe, Cr, Al) molecules and magnetic substrates (Co and Cr). Mq3 with different central metal elements but the same organic framework has dramatically different interaction with different magnetic substrates, which affect the interface state significantly. AFM coupling was observed between magnetic Mq3 molecules and ferromagnetic (Co) as well as antiferromagnetic (Cr) substrate, manifested with a superexchange and direct exchange interaction, respectively. Such strong magnetic interfacial coupling may open a gap around the Fermi level and significantly change interface transport properties. Nonmagnetic Alq3 molecule was found to enhance the interface spin polarization due to hybridization between the lowest unoccupied molecular orbitals (LUMO) of Alq3 and metallic surface state. These findings will help better understand spinterface and shed new light on future application of Mq3 molecules in spintronics devices. This work was support by NSF-MRSEC (DMR-1121252) and DOE-BES (DE-FG02-04ER46148).

Lifetime improvement mechanism in organic light-emitting diodes with mixed materials at a heterojunction interface

NASA Astrophysics Data System (ADS)

Minagawa, Masahiro; Takahashi, Noriko

2016-02-01

To investigate the lifetime improvement mechanism caused by mixing at the heterojunction interface, organic light-emitting diodes (OLEDs) with stacked and mixed 4,4‧-bis[N-(1-naphthyl)-N-phenyl-amino]-biphenyl (α-NPD)/tris(8-hydroxyquinoline)aluminum (Alq3) interfaces were fabricated, and changes in their displacement current due to continuous operation were measured. A decrease in accumulated holes at the α-NPD/Alq3 interface was observed in the stacked configuration devices over longer operations. These results indicate that the injected hole density was reduced during continuous operation, implying that the carrier balance became uneven in the emission region. However, few accumulated holes and changes in the displacement current due to continuous operation were observed in the devices having the mixed layer. Therefore, it was deduced that the number of holes concentrated between the α-NPD and Alq3 layers was decreased by mixing at the heterojunction interface, and that the change in the number of holes was smaller during continuous operation, resulting in less degradation.

Maximizing the value of gate capacitance in field-effect devices using an organic interface layer

NASA Astrophysics Data System (ADS)

Kwok, H. L.

2015-12-01

Past research has confirmed the existence of negative capacitance in organics such as tris (8-Hydroxyquinoline) Aluminum (Alq3). This work explored using such an organic interface layer to enhance the channel voltage in the field-effect transistor (FET) thereby lowering the sub-threshold swing. In particular, if the values of the positive and negative gate capacitances are approximately equal, the composite negative capacitance will increase by orders of magnitude. One concern is the upper frequency limit (∼100 Hz) over which negative capacitance has been observed. Nonetheless, this frequency limit can be raised to kHz when the organic layer is subjected to a DC bias.

Light emission in forward and reverse bias operation in OLED with amorphous silicon carbon nitride thin films

NASA Astrophysics Data System (ADS)

Reyes, R.; Cremona, M.; Achete, C. A.

2011-01-01

Amorphous silicon carbon nitride (a-SiC:N) thin films deposited by magnetron sputtering were used in the structure of an organic light emitting diode (OLED), obtaining an OLED operating in forward and reverse bias mode. The device consist of the heterojunction structure ITO/a-SiC:N/Hole Transport Layer (HTL)/ Electron Transport Layer (ETL)/a-SiC:N/Al. As hole transporting layer was used a thin film of 1-(3-methylphenyl)-1,2,3,4 tetrahydroquinoline - 6 - carboxyaldehyde - 1,1'- diphenylhydrazone (MTCD), while the tris(8-hydroxyquinoline aluminum) (Alq3) is used as electron transport and emitting layer. A significant increase in the voltage operation compared to the conventional ITO/MTCD/Alq3/Al structure was observed, so the onset of electroluminescence occurs at about 22 V in the forward and reverse bias mode of operation. The electroluminescence spectra is similar in both cases, only slightly shifted 0.14 eV to lower energies in relation to the conventional device.

Highly luminescent material based on Alq3:Ag nanoparticles.

PubMed

Salah, Numan; Habib, Sami S; Khan, Zishan H

2013-09-01

Tris (8-hydroxyquinoline) aluminum (Alq3) is an organic semiconductor molecule, widely used as an electron transport layer, light emitting layer in organic light-emitting diodes and a host for fluorescent and phosphorescent dyes. In this work thin films of pure and silver (Ag), cupper (Cu), terbium (Tb) doped Alq3 nanoparticles were synthesized using the physical vapor condensation method. They were fabricated on glass substrates and characterized by X-ray diffraction, scanning electron microscope (SEM), energy dispersive spectroscopy, atomic force microscope (AFM), UV-visible absorption spectra and studied for their photoluminescence (PL) properties. SEM and AFM results show spherical nanoparticles with size around 70-80 nm. These nanoparticles have almost equal sizes and a homogeneous size distribution. The maximum absorption of Alq3 nanoparticles is observed at 300 nm, while the surface plasmon resonant band of Ag doped sample appears at 450 nm. The PL emission spectra of Tb, Cu and Ag doped Alq3 nanoparticles show a single broad band at around 515 nm, which is similar to that of the pure one, but with enhanced PL intensity. The sample doped with Ag at a concentration ratio of Alq3:Ag = 1:0.8 is found to have the highest PL intensity, which is around 2 times stronger than that of the pure one. This enhancement could be attributed to the surface plasmon resonance of Ag ions that might have increased the absorption and then the quantum yield. These remarkable result suggest that Alq3 nanoparticles incorporated with Ag ions might be quite useful for future nano-optoelectronic devices.

Enhanced PL and EL properties of Alq3/nano-TiO2 with the modification of 8-vinyl POSS

NASA Astrophysics Data System (ADS)

Li, Jie; Xie, Bing; Xia, Kai; Zhao, Chunmao; Li, Yingchun; Hu, Shengliang

2018-04-01

In this study, tris (8-hydroxyquinoline) aluminum/nano-titanium dioxide (Alq3/nano-TiO2) composites were synthesized using a simply in-situ process with 8-vinyl polyhedral oligomeric silsesquioxane (POSS) as a modifier. The as-prepared Alq3/nano-TiO2 composites were characterized by X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet visible (UV-vis) absorption spectra. The effect of modification on luminescence properties for the samples was studied by photoluminescence (PL) spectra, electroluminescence (EL) spectra and time-resolved luminescence decay curves. Organic light emitting diodes (OLEDs) with the corresponded emitting layer structure were investigated. The results show that the amphiphilicity of the 8-vinyl POSS leads to well-dispersion state of the nano-TiO2 in the Alq3. Adding a proper weight percentage of 8-vinyl POSS is beneficial for the PL and EL properties enhancement of the composites. OLED using the Alq3/nano-TiO2 with 1 wt% 8-vinyl POSS emitting layer has the low turn-on voltage (4.7 V at 1 cd/m2), high maximum luminance (7463 cd/m2 at 8.75 V), and high luminous efficiency (1.13 cd/A at 100 mA/cm2). Adding 1 wt% 8-vinyl POSS in Alq3/nano-TiO2 can increase the EL intensity by a factor of 37.1 at 8 V. These values are better than those for OLEDs using the Alq3 emitting layer. The increase in luminance and current efficiency stability can be attributed to the energy transfer process between the Alq3 and the nano-TiO2, and the suppression of the self-quenching by caged 8-vinyl POSS molecules.

Cathode Formed by Thermal Evaporation of Ba:Al Alloy and Estimations of Barrier Height in an Organic LED

NASA Astrophysics Data System (ADS)

Ding, Lei; Zhang, Fang-Hui

2011-06-01

It is demonstrated that barium and aluminum alloy synthesized by melting in a glass tube under low vacuum is applicable for organic laser emitting diodes (LEDs) as a thin film cathode. The alloy film obtained by the thermal evaporation of pre-synthesized alloy is used in a single-boat organic LED device with the structure: indium tin oxide (ITO)/4,4'-bis[N-(1-naphthyl)-N-phenylamino]biphenyl(NPB)/tris-(8-hydroxyquinoline) aluminum(Alq3)/barium:aluminum alloy. The experimental results show that devices with this alloy film cathode exhibit better current density-voltage-luminance characteristics than those with a conventional pure Al cathode, and more weight of barium in aluminum leads to better performance of the devices. Characteristics of current density versus voltage for the electron-only devices are fitted by the Richardson—Schottky emission model, indicating that the electron injection barrier has a decrease of about 0.3 eV by this alloy cathode.

Highly efficient organic electroluminescent diodes realized by efficient charge balance with optimized electron and hole transport layers

NASA Astrophysics Data System (ADS)

Khan, M. A.; Xu, Wei; Wei, Fuxiang; Bai, Yu; Jiang, X. Y.; Zhang, Z. L.; Zhu, W. Q.

2007-11-01

Highly efficient organic electroluminescent devices (OLEDs) were developed based on 4,7-diphenyl-1, 10-phenanthroline (BPhen) as the electron transport layer (ETL), tris-(8-hydroxyquinoline) aluminum (Alq 3) as the emission layer (EML) and N,Ń-bis-[1-naphthy(-N,Ńdiphenyl-1,1'-biphenyl-4,4'-diamine)] (NPB) as the hole transport layer (HTL). The typical device structure was glass substrate/ ITO/ NPB/ Alq 3/ BPhen/ LiF/ Al. Since BPhen possesses a considerable high electron mobility of 5×10 -4 cm 2 V -1 s -1, devices with BPhen as ETL can realize an extremely high luminous efficiency. By optimizing the thickness of both HTL and ETL, we obtained a highly efficient OLED with a current efficiency of 6.80 cd/A and luminance of 1361 cd/m 2 at a current density of 20 mA/cm 2. This dramatic improvement in the current efficiency has been explained on the principle of charge balance.

Photophysics and energy transfer studies of Alq3 confined in the voids of nanoporous anodic alumina.

PubMed

Mohammadpour, Arash; Utkin, Ilya; Bodepudi, Srikrishna Chanakya; Kar, Piyush; Fedosejevs, Robert; Pramanik, Sandipan; Shankar, Karthik

2013-04-01

We report on a hierarchical nanoarchitecture wherein distinct chromophores are deterministically placed at two different types of sites in a nanoporous metal oxide framework. One chromophore, namely Tris(8-hydroxyquinoline)aluminium(III) (Alq3), is embedded in the 1-2 nm sized nanovoids of anodic aluminum oxide (AAO) and another chromophore (carboxyfluorescein or pyrenebutyric acid) is anchored in the form of a monolayer to the surface of the walls of the cylindrical nanopores (- 20 nm in diameter) of AAO. We found the luminescence maximum to occur at 492 nm, blueshifted by at least 18 nm from the value in solutions and thin films. The excited state decay of Alq3 molecules in nanovoids was found to be biexponential with a fast component of 338 ps and a slower component of 2.26 ns, different from Alq3 thin films and solutions. Using a combination of steady state and time-resolved luminescence studies, we found that efficient Forster-type resonance energy transfer (FRET) from Alq3 in the nanovoids to the carboxyfluorescein monolayer could be used to pump the emission of surface-bound chromophores. Conversely, the emission of nanovoid-confined Alq3 could be pumped by energy transfer from a pyrenebutyric acid monolayer. Such intra-nanoarchitecture interactions between chromophores deterministically placed in different spatial locations are important in applications such as organic light emitting diodes, chemical sensors, energy transfer fluorescent labels, light harvesting antennas and organic spintronics.

Sonochemical fabrication of 8-hydroxyquinoline aluminum (Alq3) nanoflowers with high electrogenerated chemiluminescence.

PubMed

Mao, Chang-Jie; Wang, Dan-Chen; Pan, Hong-Cheng; Zhu, Jun-Jie

2011-03-01

Well-defined Alq(3) nanoflowers were fabricated via a facile and fast sonochemical route. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the structure and shape of the as-prepared product. The results showed that the resulting Alq(3) was composed of nanobelts with thickness about 50 nm, average widths of 200 nm, and length up to 10 μm. The Alq(3) nanoflowers exhibited good electrogenerated chemiluminescence behavior. Copyright © 2010 Elsevier B.V. All rights reserved.

Nondispersive Electron Transport in Alq3

DTIC Science & Technology

2001-08-20

APPLIED PHYSICS LETTERS VOLUME 79, NUMBER 16 15 OCTOBER 2001Nondispersive electron transport in Alq3 George G. Malliaras,a) Yulong Shen, and David H...room temperature electron transport in amorphous films of tris ~8-hydroxyquinolinolato! aluminum ~III! ( Alq3 ) with the time-of-flight technique...We use the correlated disorder model to determine an effective dipole moment for Alq3 , and the corresponding meridional to facial isomeric ratio

Nano-Dots Enhanced White Organic Light-Emitting Diodes

DTIC Science & Technology

2006-11-30

phenolato)-aluminum (BAlq) and a 20 nm electron-transporting layer of tris(8-hydroxyl-quino- line)-aluminum ( Alq3 ) were sequentially deposited at 2...resultant red OLED at emission. The device composes structure of ITO/PEDOT: PSS/CBP: 6 wt% Btp2Ir(acac): x wt% CdSe quantum dots/BAlq/ Alq3 /LiF/ Al...The device composes struc- ture of ITO/PEDOT: PSS/CBP: 6 wt% Ir(ppy)3: x wt% CdSe quantum dots/BAlq/ Alq3 /LiF/ Al. Figure 8 shows the effect of

Numerical study of the light output intensity of the bilayer organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Lu, Feiping

2017-02-01

The structure of organic light-emitting diodes (OLEDs) is one of most important issues that influence the light output intensity (LOI) of OLEDs. In this paper, based on a simple but accurate optical model, the influences of hole and electron transport layer thickness on the LOI of bilayer OLEDs, which with N,N0- bis(naphthalen-1-yl)-N,N0- bis(phenyl)- benzidine (NPB) or N,N'- diphenyl-N,N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4-diamine (TPD) as hole transport layer, with tris(8-hydroxyquinoline) aluminum (Alq3) as electron transport and light emitting layers, were investigated. The laws of LOI for OLEDs under different organic layer thickness values were obtained. The results show that the LOI of devices varies in accordance with damped cosine or sine function as the increasing of organic layer thickness, and the results show that the bilayer OLEDs with the structure of Glass/ITO/NPB (55 nm)/Alq3 (75 nm)/Al and Glass/ITO/TPB (60 nm)/Alq3 (75 nm)/Al have most largest LOI. When the thickness of Alq3 is less than 105 nm, the OLEDs with TPD as hole transport layer have larger LOI than that with NPB as hole transport layer. The results obtained in this paper can present an in-depth understanding of the working mechanism of OLEDs and help ones fabricate high efficiency OLEDs.

[Optical and morphological investigation on the interaction of dual dopants in poly (N-vinylcarzole)].

PubMed

Zhang, Ting; Xu, Zheng; Teng, Feng; Qian, Lei; Wang, Yong-Sheng; Xu, Xu-Rong

2006-05-01

The effect of optical and electrical properties of poly(N-vinylcarzole) (PVK) doped with two dyes, i. e. 8-tris-hydroxyquinoline (Alq3) and 4-(dicyanomethylene)-2-tert-butyl-6 (1, 1, 7, 7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB), on the energy transfer and charge trapping processes was investigated. The phase separation in blends film at different doping concentration was also studied. More homogeneous dispersion of dyes in PVK with increasing doping concentration was showed. The results indicate that there is a certain interaction of Alq3 and DCJTB in this dual-doped system. It is the incorporation of DCJTB that untangled the aggregation of Alq3 owing to the interaction of DCJTB and Alq3. But for higher doping concentration, DCJTB results in an isolated charge transport channel that decreases the electroluminescence (EL) operating voltage.

Vacuum-deposited, nonpolymeric flexible organic light-emitting devices.

PubMed

Gu, G; Burrows, P E; Venkatesh, S; Forrest, S R; Thompson, M E

1997-02-01

We demonstrate mechanically flexible, organic light-emitting devices (OLED's) based on the nonpolymetric thin-film materials tris-(8-hydroxyquinoline) aluminum (Alq(3)) and N, N(?) -diphenyl- N, N(?) -bis(3-methylphenyl)1- 1(?) biphenyl-4, 4(?) diamine (TPD). The single heterostructure is vacuum deposited upon a transparent, lightweight, thin plastic substrate precoated with a transparent, conducting indium tin oxide thin film. The flexible OLED performance is comparable with that of conventional OLED's deposited upon glass substrates and does not deteriorate after repeated bending. The large-area (~1 - cm>(2)) devices can be bent without failure even after a permanent fold occurs if they are on the convex substrate surface or over a bend radius of ~0.5>cm if they are on the concave surface. Such devices are useful for ultralightweight, flexible, and comfortable full-color flat panel displays.

Indium-tin-oxide-free tris(8-hydroxyquinoline) Al organic light-emitting diodes with 80% enhanced power efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Min; Xiao, Teng; Liu, Rui

2011-10-11

Efficient indium tin oxide (ITO)-free small molecule organic light-emitting diodes (SMOLEDs) with multilayered highly conductive poly(3,4-ethylenedioxy thiophene):poly(styrenesulfonate) (PEDOT:PSS) as the anode are demonstrated. PEDOT:PSS/MoO{sub 3}/N,N'-diphenyl- N,N'-bis(1-naphthylphenyl)-1,1'-biphenyl-4,4'-diamine (NPD)/tris(8-hydroxyquinoline) Al (Alq{sub 3})/4,7-diphenyl-1,10-phenanthroline (BPhen)/LiF/Al SMOLEDs exhibited a peak power efficiency of 3.82 lm/W, 81% higher than that of similar ITO-based SMOLEDs (2.11 lm/W). The improved performance is believed to be due to the higher work function, lower refractive index, and decreased surface roughness of PEDOT:PSS vs ITO, and to Ohmic hole injection from PEDOT:PSS to the NPD layer via the MoO{sub 3} interlayer. The results demonstrate that PEDOT:PSS can substitute ITO in SMOLEDsmore » with strongly improved device performance.« less

New cyclometalated Iridium(III) beta-dicetone complex as phosphorescent dopant in Organic light emitting devices

NASA Astrophysics Data System (ADS)

Ivanov, P.; Petrova, P.; Stanimirov, S.; Tomova, R.

2017-01-01

A new Bis[4-(benzothiazolato-N,C2‧-2-yl)-N,N-dimethylaniline]Iridium(III) acetylacetonate (Me2N-bt) 2Ir(acac) was synthesized and identified by 1H NMR and elemental analysis. The application of the new compound as a dopant in the hole transporting layer (HTL) of Organic light emitting diode (OLED) structure: HTL/EL/ETL, where HTL was N,N’-bis(3-methylphenyl)-N,N’-diphenylbenzidine (TPD), incorporated in Poly(N-vinylcarbazole) (PVK) matrix, EL - electroluminescent layer of Bis(8-hydroxy-2-methylquinoline)-(4-phenylpheno-xy)aluminum (BAlq) and ETL - electron-transporting layer of Tris-(8-hydroxyquinoline) aluminum (Alq3) or Bis[2-(2-benzothiazoly) phenolato]zinc (Zn(btz)2). We established that the electroluminescent spectra of OLEDs at different concentrations of the dopant were basically the sum of the greenish-blue emission of BAlq and yellowish-green emission of Ir complex. It was found that with increasing of the dopant concentration the relative electroluminescent intensity of Iridium complex emission increased and this of BAlq decreased and as a result the fine tuning of OLED color was observed.

Spin-Polarized Hybridization at the interface between different 8-hydroxyquinolates and the Cr(001) surface

NASA Astrophysics Data System (ADS)

Wang, Jingying; Deloach, Andrew; Dougherty, Daniel B.; Dougherty Lab Team

Organic materials attract a lot of attention due to their promising applications in spintronic devices. It is realized that spin-polarized metal/organic interfacial hybridization plays an important role to improve efficiency of organic spintronic devices. Hybridized interfacial states help to increase spin injection at the interface. Here we report spin-resolved STM measurements of single tris(8-hydroxyquinolinato) aluminum molecules adsorbed on the antiferromagnetic Cr(001). Our observations show a spin-polarized interface state between Alq3 and Cr(001). Tris(8-hydroxyquinolinato) chromium has also been studied and compared with Alq3, which exhibits different spin-polarized hybridization with the Cr(001) surface state than Alq3. We attribute the differences to different character of molecular orbitals in the two different quinolates.

Fused Methoxynaphthyl Phenanthrimidazole Semiconductors as Functional Layer in High Efficient OLEDs.

PubMed

Jayabharathi, Jayaraman; Ramanathan, Periyasamy; Karunakaran, Chockalingam; Thanikachalam, Venugopal

2016-01-01

Efficient hole transport materials based on novel fused methoxynaphthyl phenanthrimidazole core structure were synthesised and characterized. Their device performances in phosphorescent organic light emitting diodes were investigated. The high thermal stability in combination with the reversible oxidation process made promising candidates as hole-transporting materials for organic light-emitting devices. Highly efficient Alq3-based organic light emitting devices have been developed using phenanthrimidazoles as functional layers between NPB [4,4-bis(N-(1-naphthyl)-N-phenylamino)biphenyl] and Alq3 [tris(8-hydroxyquinoline)aluminium] layers. Using the device of ITO/NPB/4/Alq3/LiF/Al, a maximum luminous efficiency of 5.99 cd A(-1) was obtained with a maximum brightness of 40,623 cd m(-2) and a power efficiency of 5.25 lm W(-1).

Low intrinsic carrier density LSMO/Alq3/AlOx/Co organic spintronic devices

NASA Astrophysics Data System (ADS)

Riminucci, Alberto; Graziosi, Patrizio; Calbucci, Marco; Cecchini, Raimondo; Prezioso, Mirko; Borgatti, Francesco; Bergenti, Ilaria; Dediu, Valentin Alek

2018-04-01

The understanding of spin injection and transport in organic spintronic devices is still incomplete, with some experiments showing magnetoresistance and others not detecting it. We have investigated the transport properties of a large number of tris-(8-hydroxyquinoline)aluminum-based organic spintronic devices with an electrical resistance greater than 5 MΩ that did not show magnetoresistance. Their transport properties could be described satisfactorily by known models for organic semiconductors. At high voltages (>2 V), the results followed the model of space charge limited current with a Poole-Frenkel mobility. At low voltages (˜0.1 V), that are those at which the spin valve behavior is usually observed, the charge transport was modelled by nearest neighbor hopping in intra-gap impurity levels, with a charge carrier density of n0 = (1.44 ± 0.21) × 1015 cm-3 at room temperature. Such a low carrier density can explain why no magnetoresistance was observed.

Atomistic simulation on charge mobility of amorphous tris(8-hydroxyquinoline) aluminum (Alq3): origin of Poole-Frenkel-type behavior.

PubMed

Nagata, Yuki; Lennartz, Christian

2008-07-21

The atomistic simulation of charge transfer process for an amorphous Alq(3) system is reported. By employing electrostatic potential charges, we calculate site energies and find that the standard deviation of site energy distribution is about twice as large as predicted in previous research. The charge mobility is calculated via the Miller-Abrahams formalism and the master equation approach. We find that the wide site energy distribution governs Poole-Frenkel-type behavior of charge mobility against electric field, while the spatially correlated site energy is not a dominant mechanism of Poole-Frenkel behavior in the range from 2x10(5) to 1.4x10(6) V/cm. Also we reveal that randomly meshed connectivities are, in principle, required to account for the Poole-Frenkel mechanism. Charge carriers find a zigzag pathway at low electric field, while they find a straight pathway along electric field when a high electric field is applied. In the space-charge-limited current scheme, the charge-carrier density increases with electric field strength so that the nonlinear behavior of charge mobility is enhanced through the strong charge-carrier density dependence of charge mobility.

SPR sensors for monitoring the degradation processes of Eu(dbm)3(phen) and Alq3 thin films under atmospheric and UVA exposure

NASA Astrophysics Data System (ADS)

Del Rosso, T.; Zaman, Q.; Cremona, M.; Pandoli, O.; Barreto, A. R. J.

2018-06-01

The degradation processes of tris(8-hydroxyquinoline) (Alq3) and tris(dibenzoylmethane) mono(1,10-phenanthroline)europium(III) (Eu(dbm)3(phen)) thin films are investigated by the use of AFM, photoluminescence and SPR spectroscopy. The plasmonic sensors are operated both in air and nitrogen environments, where they are irradiated with controlled doses of UVA radiation. AFM results don't reveal the formation of heterogeneous phases and crystallization under air exposure. The organic thin films change their refractive index under both types of exposure and act as a protective layer against oxidation for the SiO2/MPTS/metal interface of the plasmonic sensors. SPR measurements reveal a strict correlation between the refractive index increase and quenching of the photoluminescence of the organic thin films. The results are promising for the development of compact plasmonic UVA dosimeters in the surface plasmon coupled emission configuration (SPCE) with lanthanide β-diketonate complex materials (patent pending).

Determination of the Width of the Carrier Recombination Zone in Organic Light-Emitting Diodes

DTIC Science & Technology

2003-09-18

biphenyl-4,48-diamine ~TPD!/tris-~8-hydroxyquinolinato! aluminum III ( Alq3 )/ Mg:Ag. In addition, an independent evaluation of the light output coupling...5 min. TPD, obtained from H. W. Sands, was used as the hole transport layer and Alq3 , ob- tained from TCI America, was used as the emitting/electron...transport layer. TPD was used as received while Alq3 was purified by train sublimation. A 100 nm thick Mg:Ag film,4 © 2003 American Institute of

Manipulating Refractive Index in Organic Light-Emitting Diodes.

PubMed

Salehi, Amin; Chen, Ying; Fu, Xiangyu; Peng, Cheng; So, Franky

2018-03-21

In a conventional organic light-emitting diode (OLED), only a fraction of light can escape to the glass substrate and air. Most radiation is lost to two major channels: waveguide modes and surface plasmon polaritons. It is known that reducing the refractive indices of the constituent layers in an OLED can enhance light extraction. Among all of the layers, the refractive index of the electron transport layer (ETL) has the largest impact on light extraction because it is the layer adjacent to the metallic cathode. Oblique angle deposition (OAD) provides a way to manipulate the refractive index of a thin film by creating an ordered columnar void structure. In this work, using OAD, the refractive index of tris(8-hydroxyquinoline)aluminum (Alq3) can be tuned from 1.75 to 1.45. With this low-index ETL deposited by OAD, the resulting phosphorescent OLED shows nearly 30% increase in light extraction efficiency.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, J.; Walters, D. M.; Zhou, D.

Vapor-deposited glasses can be anisotropic and molecular orientation is important for organic electronics applications. In organic light emitting diodes (OLEDs), for example, the orientation of dye molecules in two-component emitting layers significantly influences emission efficiency. Here we investigate how substrate temperature during vapor deposition influences the orientation of dye molecules in a model two-component system. We determine the average orientation of a linear blue light emitter 1,4-di-[4-( N,N-diphenyl)amino]styrylbenzene (DSA-Ph) in mixtures with aluminum-tris(8-hydroxyquinoline) (Alq 3) by spectroscopic ellipsometry and IR dichroism. We find that molecular orientation is controlled by the ratio of the substrate temperature during deposition and the glassmore » transition temperature of the mixture. Furthermore, these findings extend recent results for single component vapor-deposited glasses and suggest that, during vapor deposition, surface mobility allows partial equilibration towards orientations preferred at the free surface of the equilibrium liquid.« less

Plastic lab-on-a-chip for fluorescence excitation with integrated organic semiconductor lasers.

PubMed

Vannahme, Christoph; Klinkhammer, Sönke; Lemmer, Uli; Mappes, Timo

2011-04-25

Laser light excitation of fluorescent markers offers highly sensitive and specific analysis for bio-medical or chemical analysis. To profit from these advantages for applications in the field or at the point-of-care, a plastic lab-on-a-chip with integrated organic semiconductor lasers is presented here. First order distributed feedback lasers based on the organic semiconductor tris(8-hydroxyquinoline) aluminum (Alq3) doped with the laser dye 4-dicyanomethylene-2-methyl-6-(p-dimethylaminostyril)-4H-pyrane (DCM), deep ultraviolet induced waveguides, and a nanostructured microfluidic channel are integrated into a poly(methyl methacrylate) (PMMA) substrate. A simple and parallel fabrication process is used comprising thermal imprint, DUV exposure, evaporation of the laser material, and sealing by thermal bonding. The excitation of two fluorescent marker model systems including labeled antibodies with light emitted by integrated lasers is demonstrated.

Intensity and temperature-dependent photoluminescence of tris (8-hydroxyquinoline) aluminum films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ajward, A. M.; Wang, X.; Wagner, H. P.

2013-12-04

We investigate the recombination of excitons in tris (8-hydroxyquinoline) aluminum films by intensity and temperature dependent time-resolved photoluminescence (PL). At low temperature (15 K) and elevated excitation intensity the radiative emission is quenched by singlet-singlet annihilation processes. With rising temperature the PL quenching is strongly reduced resulting in a PL efficiency maximum at ∼170 K. The reduced exciton annihilation is attributed to thermally activated occupation of non-quenchable trapped exciton states. Above 170 K the PL efficiency decreases due to thermal de-trapping of radiative states and subsequent migration to non-radiative centers.

Characterization of molecular disorder in vapor-deposited thin films of aluminum tris(quinoline-8-olate) by one-dimensional 27Al NMR under magic angle spinning.

PubMed

Utz, Marcel; Nandagopal, Magesh; Mathai, Mathew; Papadimitrakopoulos, Fotios

2006-01-21

Aluminum tris (quinoline-8-olate) (Alq3) is used as an electron-transport layer in organic light-emitting diodes. The material can be obtained in a wide range of different solid phases, both crystalline and amorphous, by deposition from the vapor phase or from solution under controlled conditions. While the structure of the crystalline polymorphs of Alq3 has been investigated thoroughly by x-ray diffraction as well as solid-state NMR, very little information is currently available on the amount of structural disorder in the amorphous forms of Alq3. In the present contribution, we report the use of 27Al NMR spectroscopy in the solid state under magic angle spinning to extract such information from amorphous vapor deposits of Alq3. The NMR spectra obtained from these samples exhibit different degrees of broadening, reflecting distributions of the electric-field gradient tensor at the site of the aluminum ion. These distributions can be obtained from the NMR spectra by solving the corresponding inverse problem. From these results, the magnitude of structural disorder in terms of molecular geometry has been estimated by density-functional theory calculations. It was found that the electric-field gradient anisotropy delta follows a bimodal distribution. Its majority component is centered around delta values comparable to the meridianal alpha crystal polymorph and has a width of about 10%, corresponding to distortions of the molecular geometry of a few degrees in the orientation of the ligands. Alq3 samples obtained at higher deposition rates exhibit higher degrees of disorder. The minor component, present at about 7%, has a much smaller anisotropy, suggesting that it may be due to the facial isomer of Alq3.

Effect of Zinc Oxide Doping on Electroluminescence and Electrical Behavior of Metalloporphyrins-Doped Samarium Complex

NASA Astrophysics Data System (ADS)

Janghouri, Mohammad; Amini, Mostafa M.

2018-02-01

Samarium complex [(Sm(III)] as a new host material was used for preparation of red organic light-emitting diodes (OLEDs). Devices with configurations of indium-doped tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):(poly(styrenesulfonate) (PEDOT:PSS (50 nm)/polyvinyl carbazole (PVK):[zinc oxide (ZnO)] (50 nm)/[(Sm(III)]:[zinc(II) 2,3-tetrakis(dihydroxyphenyl)-porphyrin and Pt(II) 2,3-dimethoxyporphyrin] (60 nm)/2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) (15 nm)/Al (150 nm) have been fabricated and investigated. An electroplex occurring at the (PVK/Sm: Pt(II) 2,3-dimethoxyporphyrin) interface has been suggested when ZnO nanoparticles were doped in PVK. OLED studies have revealed that the photophysical characteristics and electrical behavior of devices with ZnO nanoparticles are much better than those of devices with pure PVK. The efficiency of devices based on [(Sm(III)] was superior than that of known aluminum tris(8-hydroxyquinoline) (Alq3) and also our earlier reports on red OLEDs under the same conditions.

Polarizable atomistic calculation of site energy disorder in amorphous Alq3.

PubMed

Nagata, Yuki

2010-02-01

A polarizable molecular dynamics simulation and calculation scheme for site energy disorder is presented in amorphous tris(8-hydroxyquinolinato)aluminum (Alq(3)) by means of the charge response kernel (CRK) method. The CRK fit to the electrostatic potential and the tight-binding approximation are introduced, which enables modeling of the polarizable electrostatic interaction for a large molecule systematically from an ab initio calculation. The site energy disorder for electron and hole transfers is calculated in amorphous Alq(3) and the effect of the polarization on the site energy disorder is discussed.

Pulser Laser Deposition of Transparent Conducting Thin Films on Flexible Substrates

DTIC Science & Technology

2001-01-19

8217-diphenyl-4,4’diamine (TPD), 50, and an electron 9 transport/emitting layer (ETL/EML) 20, of tris (8-hydroxyquinolinolato) aluminum (III) ( Alq3 ), 10...nm 0 nm 300 nm Fig.6(a) r—1 20 nm 300 10 nm 0 nm 150 300 nm Fig. 6(b) MgAg 30 Alq3 (70iim) TPD (50nm) 20 10 ITO PET substrate 40

Preparation of tris(8-hydroxyquinolinato)aluminum thin films by sputtering deposition using powder and pressed powder targets

NASA Astrophysics Data System (ADS)

Kawasaki, Hiroharu; Ohshima, Tamiko; Yagyu, Yoshihito; Ihara, Takeshi; Tanaka, Rei; Suda, Yoshiaki

2017-06-01

Tris(8-hydroxyquinolinato)aluminum (Alq3) thin films, for use in organic electroluminescence displays, were prepared by a sputtering deposition method using powder and pressed powder targets. Experimental results suggest that Alq3 thin films can be prepared using powder and pressed powder targets, although the films were amorphous. The surface color of the target after deposition became dark brown, and the Fourier transform infrared spectroscopy spectrum changed when using a pressed powder target. The deposition rate of the film using a powder target was higher than that using a pressed powder target. That may be because the electron and ion densities of the plasma generated using the powder target are higher than those when using pressed powder targets under the same deposition conditions. The properties of a thin film prepared using a powder target were almost the same as those of a film prepared using a pressed powder target.

Controlled Self-Assembly of Low-Dimensional Alq3 Nanostructures from 1D Nanowires to 2D Plates via Intermolecular Interactions

NASA Astrophysics Data System (ADS)

Gu, Jianmin; Yin, Baipeng; Fu, Shaoyan; Jin, Cuihong; Liu, Xin; Bian, Zhenpan; Li, Jianjun; Wang, Lu; Li, Xiaoyu

2018-03-01

Due to the intense influence of the shape and size of the photon building blocks on the limitation and guidance of optical waves, an important strategy is the fabrication of different structures. Herein, organic semiconductor tris-(8-hydroxyquinoline)aluminium (Alq3) nanostructures with controllable morphology, ranging from one-dimensional nanowires to two-dimensional plates, have been prepared through altering intermolecular interactions with employing the anti-solvent diffusion cooperate with solvent-volatilization induced self-assembly method. The morphologies of the formed nanostructures, which are closely related to the stacking modes of the molecules, can be exactly controlled by altering the polarity of anti-solvents that can influence various intermolecular interactions. The synthesis strategy reported here can potentially be extended to other functional organic nanomaterials.

Fabrication and Measurement of Electroluminescence and Electrical Properties of Organic Light-Emitting Diodes Containing Mott Insulator Nanocrystals.

PubMed

Nozoe, Soichiro; Kinoshita, Nobuaki; Matsuda, Masaki

2016-04-01

By using the short-time electrocrystallization technique, phthalocyanine (Pc)-based Mott insulator Co(Pc)(CN)2 . 2CHCl3 nanocrystals were fabricated and applied to organic light-emiting diodes (OLEDs). The fabricated device having the configuration ITO/Co(Pc)(CN)2 . 2CHCl3/Alq3/Al, in which ITO is indium-tin oxide and Alq3 is tris(8-hydroxyquinolinato)aluminum, showed clear emission from Alq3, suggesting the Mott insulator Co(Pc)(CN)2 . 2CHCl3 can work as useful hole-injection and transport material in OLEDs.

Fabrication and Characterization of Flexible Organic Light Emitting Diodes Based on Transparent Flexible Clay Substrates

NASA Astrophysics Data System (ADS)

Venkatachalam, Shanmugam; Hayashi, Hiromichi; Ebina, Takeo; Nakamura, Takashi; Nanjo, Hiroshi

2013-03-01

In the present work, transparent flexible polymer-doped clay (P-clay) substrates were prepared for flexible organic light emitting diode (OLED) applications. Nanocrystalline indium tin oxide (ITO) thin films were prepared on P-clay substrates by ion-beam sputter deposition method. The structural, optical, and electrical properties of as-prepared ITO/P-clay showed that the as-prepared ITO thin film was amorphous, and the average optical transparency and sheet resistance were around 84% and 56 Ω/square, respectively. The as-prepared ITO/P-clay samples were annealed at 200 and 270 °C for 1 h to improve the optical transparency and electrical conductivity. The average optical transparency was found to be maximum at an annealing temperature of 200 °C. Finally, N,N-bis[(1-naphthyl)-N,N '-diphenyl]-1,1'-biphenyl)-4,4'-diamine (NPB), tris(8-hydroxyquinoline) aluminum (Alq3) thin films, and aluminum (Al) electrode were prepared on ITO/P-clay substrates by thermal evaporation method. The current density-voltage (J-V) characteristic of Al/NPB/ITO/P-clay showed linear Ohmic behaviour. In contrast, J-V characteristic of Al/Alq3/NPB/ITO/P-clay showed non-linear Schottky behaviour. Finally, a very flexible OLED was successfully fabricated on newly fabricated transparent flexible P-clay substrates. The electroluminescence study showed that the emission intensity of light from the flexible OLED device gradually increased with increasing applied voltage.

Molecular origin of differences in hole and electron mobility in amorphous Alq3--a multiscale simulation study.

PubMed

Fuchs, Andreas; Steinbrecher, Thomas; Mommer, Mario S; Nagata, Yuki; Elstner, Marcus; Lennartz, Christian

2012-03-28

In order to determine the molecular origin of the difference in electron and hole mobilities of amorphous thin films of Alq(3) (meridional Alq(3) (tris(8-hydroxyquinoline) aluminium)) we performed multiscale simulations covering quantum mechanics, molecular mechanics and lattice models. The study includes realistic disordered morphologies, polarized site energies to describe diagonal disorder, quantum chemically calculated transfer integrals for the off-diagonal disorder, inner sphere reorganization energies and an approximative scheme for outer sphere reorganization energies. Intermolecular transfer rates were calculated via Marcus-theory and mobilities were simulated via kinetic Monte Carlo simulations and by a Master Equation approach. The difference in electron and hole mobility originates from the different localization of charge density in the radical anion (more delocalized) compared to the radical cation (more confined). This results in higher diagonal disorder for holes and less favourable overlap properties for the hole transfer integrals leading to an overall higher electron mobility.

Device characteristics of organic light-emitting diodes based on electronic structure of the Ba-doped Alq3 layer.

PubMed

Lim, Jong Tae; Kim, Kyung Nam; Yeom, Geun Young

2009-12-01

Organic light-emitting diodes (OLEDs) with a Ba-doped tris(8-quinolinolato)aluminum(III) (Alq3) layer were fabricated to reduce the barrier height for electron injection and to improve the electron conductivity. In the OLED consisting of glass/ITO/4,4',4"-tris[2-naphthylphenyl-1-phenylamino]triphenylamine (2-TNATA, 30 nm)/4,4'-bis[N-(1-napthyl)-N-phenyl-amino]-biphenyl (NPB, 18 nm)/Alq3 (42 nm)/Ba-doped Alq3 (20 nm, x%: x = 0, 10, 25, and 50)/Al (100 nm), the device with the Alq3 layer doped with 10% Ba showed the highest light out-coupling characteristic. However, as the Ba dopant concentration was increased from 25% to 50%, this device characteristic was largely reduced. The characteristics of these devices were interpreted on the basis of the chemical reaction between Ba and Alq3 and the electron injection property by analyzing the electronic structure of the Ba-doped Alq3 layer. At a low Ba doping of 10%, mainly the Alq3 radical anion species was formed. In addition, the barrier height for electron injection in this layer was decreased to 0.6 eV, when compared to the pristine Alq3 layer. At a high Ba doping of 50%, the Alq3 molecules were severely decomposed. When the Ba dopant concentration was changed, the light-emitting characteristics of the devices were well coincided with the formation mechanism of Alq3 radical anion and Alq3 decomposition species.

Effect of the electric field during annealing of organic light emitting diodes for improving its on/off ratio.

PubMed

Sharma, Rahul K; Katiyar, Monica; Rao, I V Kameshwar; Unni, K N Narayanan; Deepak

2016-01-28

If an organic light emitting diode is to be used as part of a matrix addressed array, it should exhibit low reverse leakage current. In this paper we present a method to improve the on/off ratio of such a diode by simultaneous application of heat and electric field post device fabrication. A green OLED with excellent current efficiency was seen to be suffering from a poor on/off ratio of 10(2). After examining several combinations of annealing along with the application of a reverse bias voltage, the on/off ratio of the same device could be increased by three orders of magnitude, specifically when the device was annealed at 80 °C under reverse bias (-15 V) followed by slow cooling also under the same bias. Simultaneously, the forward characteristics of the device were relatively unaffected. The reverse leakage in the OLED is mainly due to the injection of minority carriers in the hole transport layer (HTL) and the electron transport layer (ETL), in this case, of holes in tris-(8-hydroxyquinoline)aluminum(Alq3) and electrons in 4,4',4''-tris(N-3-methylphenyl-N-phenylamino)triphenylamine (m-MTDATA). Hence, to investigate these layers adjacent to the electrodes, we fabricated their single layer devices. The possibility of bulk traps present adjacent to electrodes providing states for injection was ruled out after estimating the trap density both before and after the reverse biased annealing. The temperature independent current in reverse bias ruled out the possibility of thermionic injection. The origin of the reverse bias current is attributed to the availability of interfacial hole levels in Alq3 at the cathode work function level in the as-fabricated device; the suppression of the same being attributed to the fact that these levels in Alq3 are partly removed after annealing under an electric field.

Degradation of Bilayer Organic Light-Emitting Diodes Studied by Impedance Spectroscopy.

PubMed

Sato, Shuri; Takata, Masashi; Takada, Makoto; Naito, Hiroyoshi

2016-04-01

The degradation of bilayer organic light-emitting diodes (OLEDs) with a device structure of N,N'-di(1-naphthyl)-N,N'-diphenylbenzidine (α-NPD) (hole transport layer) and tris-(8-hydroxyquinolate)aluminum (Alq3) (emissive layer and electron transport layer) has been studied by impedance spectroscopy and device simulation. Two modulus peaks are found in the modulus spectra of the OLEDs below the electroluminescence threshold. After aging of the OLEDs, the intensity of electroluminescence is degraded and the modulus peak due to the Alq3 layer is shifted to lower frequency, indicating that the resistance of the Alq3 layer is increased. Device simulation reveals that the increase in the resistance of the Alq3 layer is due to the decrease in the electron mobility in the Alq3 layer.

Substrate temperature controls molecular orientation in two-component vapor-deposited glasses

DOE PAGES

Jiang, J.; Walters, D. M.; Zhou, D.; ...

2016-02-22

Vapor-deposited glasses can be anisotropic and molecular orientation is important for organic electronics applications. In organic light emitting diodes (OLEDs), for example, the orientation of dye molecules in two-component emitting layers significantly influences emission efficiency. Here we investigate how substrate temperature during vapor deposition influences the orientation of dye molecules in a model two-component system. We determine the average orientation of a linear blue light emitter 1,4-di-[4-( N,N-diphenyl)amino]styrylbenzene (DSA-Ph) in mixtures with aluminum-tris(8-hydroxyquinoline) (Alq 3) by spectroscopic ellipsometry and IR dichroism. We find that molecular orientation is controlled by the ratio of the substrate temperature during deposition and the glassmore » transition temperature of the mixture. Furthermore, these findings extend recent results for single component vapor-deposited glasses and suggest that, during vapor deposition, surface mobility allows partial equilibration towards orientations preferred at the free surface of the equilibrium liquid.« less

Lithium hydride doped intermediate connector for high-efficiency and long-term stable tandem organic light-emitting diodes.

PubMed

Ding, Lei; Tang, Xun; Xu, Mei-Feng; Shi, Xiao-Bo; Wang, Zhao-Kui; Liao, Liang-Sheng

2014-10-22

Lithium hydride (LiH) is employed as a novel n-dopant in the intermediate connector for tandem organic light-emitting diodes (OLEDs) because of its easy coevaporation with other electron transporting materials. The tandem OLEDs with two and three electroluminescent (EL) units connected by a combination of LiH doped 8-hydroxyquinoline aluminum (Alq3) and 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile (HAT-CN) demonstrate approximately 2-fold and 3-fold enhancement in current efficiency, respectively. In addition, no extra voltage drop across the intermediate connector is observed. Particularly, the lifetime (T75%) in the tandem OLED with two and three EL units is substantially improved by 3.8 times and 7.4 times, respectively. The doping effect of LiH into Alq3, the charge injection, and transport characteristics of LiH-doped Alq3 are further investigated by ultraviolet photoelectron spectroscopy (UPS) and X-ray photoemission spectroscopy (XPS).

Statistical Paradigm for Organic Optoelectronic Devices: Normal Force Testing for Adhesion of Organic Photovoltaics and Organic Light-Emitting Diodes.

PubMed

Vasilak, Lindsay; Tanu Halim, Silvie M; Das Gupta, Hrishikesh; Yang, Juan; Kamperman, Marleen; Turak, Ayse

2017-04-19

In this study, we assess the utility of a normal force (pull-test) approach to measuring adhesion in organic solar cells and organic light-emitting diodes. This approach is a simple and practical method of monitoring the impact of systematic changes in materials, processing conditions, or environmental exposure on interfacial strength and electrode delamination. The ease of measurement enables a statistical description with numerous samples, variant geometry, and minimal preparation. After examining over 70 samples, using the Weibull modulus and the characteristic breaking strength as metrics, we were able to successfully differentiate the adhesion values between 8-tris(hydroxyquinoline aluminum) (Alq 3 ) and poly(3-hexyl-thiophene) and [6,6]-phenyl C61-butyric acid methyl ester (P3HT:PCBM) interfaces with Al and between two annealing times for the bulk heterojunction polymer blends. Additionally, the Weibull modulus, a relative measure of the range of flaw sizes at the fracture plane, can be correlated with the roughness of the organic surface. Finite element modeling of the delamination process suggests that the out-of-plane elastic modulus for Alq 3 is lower than the reported in-plane elastic values. We suggest a statistical treatment of a large volume of tests be part of the standard protocol for investigating adhesion to accommodate the unavoidable variability in morphology and interfacial structure found in most organic devices.

Synthesis and characterization of organic/inorganic heterostructure films for hybrid light emitting diode

NASA Astrophysics Data System (ADS)

Toyama, Toshihiko; Ichihara, Tokuyuki; Yamaguchi, Daisuke; Okamoto, Hiroaki

2007-10-01

Thin-film light emitting devices based on organic materials have been gathering attentions for applying a flat-panel display and a solid-state lighting. Alternatively, inorganic technologies such as Si-based thin-film technology have been growing almost independently. It is then expected that combining the Si-based thin-film technology with the organic light emitting diode (OLED) technology will develop innovative devices. Here, we report syntheses of the hybrid light emitting diode (LED) with a heterostructure consisting of p-type SiC x and tris-(8-hydroxyquinoline) aluminum films and characterization for the hybrid LEDs. We present the energy diagram of the heterostructure, and describe that the use of high dark conductivities of the p-type SiC x as well as inserting wide-gap intrinsic a-SiC x at the p-type SiC x/Alq interface are effective for improving device performance.

Surface-potential undulation of Alq3 thin films prepared on ITO, Au, and n-Si.

PubMed

Ozasa, Kazunari; Ito, Hiromi; Maeda, Mizuo; Hara, Masahiko

2012-01-01

The surface potential (SP) morphology on thin films of tris(8-hydroxyquinolinato) aluminum (Alq3) was investigated with Kelvin probe force microscopy. Thin Alq3 films of 100 nm were prepared on ITO/glass substrates, Au/mica substrates, and n-Si substrates. Cloud-like morphologies of the SP undulation with 200-400 nm in lateral size were observed for all three types of the substrates. New larger peaks were observed in the cloud-like morphologies when the surfaces were exposed shortly to a light, while the SP average was reduced monotonically. The nonuniform distribution of charged traps and mobility was deduced from the SP undulation morphology and its photoexposure dependences.

Improved performance of organic light-emitting diodes with MoO3 interlayer by oblique angle deposition.

PubMed

Liu, S W; Divayana, Y; Sun, X W; Wang, Y; Leck, K S; Demir, H V

2011-02-28

We fabricated and demonstrated improved organic light emitting diodes (OLEDs) in a thin film architecture of indium tin oxide (ITO)/ molybdenum trioxide (MoO3) (20 nm)/N,N'-Di(naphth-2-yl)-N,N'-diphenyl-benzidine (NPB) (50 nm)/ tris-(8-hydroxyquinoline) (Alq3) (70 nm)/Mg:Ag (200 nm) using an oblique angle deposition technique by which MoO3 was deposited at oblique angles (θ) with respect to the surface normal. It was found that, without sacrificing the power efficiency of the device, the device current efficiency and external quantum efficiency were significantly enhanced at an oblique deposition angle of θ=60° for MoO3.

Oligonucleotide assisted light-emitting Alq3 microrods: energy transfer effect with fluorescent dyes.

PubMed

Cui, Chunzhi; Park, Dong Hyuk; Kim, Jeongyong; Joo, Jinsoo; Ahn, Dong June

2013-06-14

Oligonucleotide assisted tri(8-hydroxyquinoline) aluminium (Alq3) microrods were prepared for the first time. When hybridized with oligonucleotide labeled by Cy3 fluorescent dye, a significant photoluminescence variation of the Alq3 microrods was observed due to Förster resonance energy transfer, unlike when Cy5-oligonucleotide was used. Versatile nucleotide manipulation would open up wider applications of Alq3-based materials, based on this fundamental observation.

[Optical and electrical properties of NPB/Alq3 organic quantum well].

PubMed

Huang, Jin-Zhao; Xu, Zheng; Zhao, Su-Ling; Zhang, Fu-Jun; Wang, Yong

2007-04-01

In the present paper, the organic quantum-well device similar to the type-II quantum well of inorganic semiconductor material was prepared by heat evaporation. NPB (N, N'-di-[(1-naphthalenyl)-N, N'-diphenyl]-(1,1'-biphenyl)-4,4'-diamine) and Alq3 (Tris-(8-quinolinolato) aluminum) act as the potential barrier layer and the potential well layer respectively. Besides, the single layer structure of Alq3 was prepared. In the experiments, the Forster nonradiative resonant energy transfer from the barrier layer to the well layer was identified, and the quantum well luminescence device possesses a favorable current-voltage property. The narrowing of spectrum was observed, and the spectrum shifted to blue region continuously when the applied voltage increased.

Synthesis and electroluminescence characterization of a new aluminum complex, [8-hydroxyquinoline] bis [2, 2'bipyridine] aluminum Al(Bpy)2q

NASA Astrophysics Data System (ADS)

Rahul, Kumar; Ritu, Srivastava; Punita, Singh

2016-01-01

We have synthesized and characterized a new electroluminescent material, [8-hydroxyquinoline] bis [2,2'bipyridine] aluminum. A solution of this material Al(Bpy)2q in toluene showed absorption maxima at 380 nm, which was attributed to the moderate energy (π-π*) transitions of the aromatic rings. The photoluminescence spectrum of Al(Bpy)2q in the toluene solution showed a peak at 518 nm. This material shows thermal stability up to 300 °C. The structure of the device is ITO/F4-TCNQ (1 nm)/α-NPD (35 nm)/Al(Bpy)2q (35 nm)/ BCP (6 nm)/Alq3 (28 nm)/LiF (1 nm)/Al (150 nm). This device exhibited a luminescence peak at 515 nm (CIE coordinates, x = 0.32, y = 0.49). The maximum luminescence of the device was 214 cd/m2 at 21 V. The maximum current efficiency of OLED was 0.12 cd/A at 13 V and the maximum power efficiency was 0.03 lm/W at 10 V.

Hole transporting material 5, 10, 15-tribenzyl-5H-diindolo[3, 2-a:3‧, 2‧-c]-carbazole for efficient optoelectronic applications as an active layer

NASA Astrophysics Data System (ADS)

Zheng, Yan-Qiong; J. Potscavage, William, Jr.; Zhang, Jian-Hua; Wei, Bin; Huang, Rong-Juan

2015-02-01

In order to explore the novel application of the transparent hole-transporting material 5,10,15-tribenzyl-5H-diindolo[3,2-a:3‧,2‧-c]-carbazole (TBDI), in this article TBDI is used as an active layer but not a buffer layer in a photodetector (PD), organic light-emitting diode (OLED), and organic photovoltaic cell (OPV) for the first time. Firstly, the absorption and emission spectra of a blend layer comprised of TBDI and electron-transporting material bis-(2-methyl-8-quinolinate) 4-phenylphenolate (BAlq) are investigated. Based on the absorption properties, an organic PD with a peak absorption at 320 nm is fabricated, and a relatively-high detectivity of 2.44 × 1011 cm·Hz1/2/W under 320-nm illumination is obtained. The TBDI/tris (8-hydroxyquinoline) aluminum (Alq3) OLED device exhibits a comparable external quantum efficiency and current efficiency to a traditional 4, 4-bis[N-(1-naphthyl)-N-phenyl-amino]biphenyl (α-NPD)/Alq3 OLED. A C70-based Schottky junction with 5 wt%-TBDI yields a power conversion efficiency of 5.0%, which is much higher than 1.7% for an α-NPD-based junction in the same configuration. These results suggest that TBDI has some promising properties which are in favor of the hole-transporting in Schottky junctions with a low-concentration donor. Project supported by the Funding Program for World-Leading Innovative R & D on Science and Technology (FIRST) from JSPS, the Fund from the Science and Technology Commission of Shanghai Municipality, China (Grant Nos. 14DZ2280900 and 14XD1401800), and the Natural Science Foundation of Shanghai (Grant No. 15ZR1416600).

Efficient blue and white polymer light emitting diodes based on a well charge balanced, core modified polyfluorene derivative.

PubMed

Das, Dipjyoti; Gopikrishna, Peddaboodi; Singh, Ashish; Dey, Anamika; Iyer, Parameswar Krishnan

2016-03-14

Fabrication of efficient blue and white polymer light-emitting diodes (PLEDs) using a well charge balanced, core modified polyfluorene derivative, poly[2,7-(9,9'-dioctylfluorene)-co-N-phenyl-1,8-naphthalimide (99:01)] (PFONPN01), is presented. The excellent film forming properties as observed from the morphological study and the enhanced electron transport properties due to the inclusion of the NPN unit in the PFO main chain resulted in improved device properties. Bright blue light was observed from single layer PLEDs with PFONPN01 as an emissive layer (EML) as well as from double layer PLEDs using tris-(8-hydroxyquinoline) aluminum (Alq3) as an electron transporting layer (ETL) and LiF/Al as a cathode. The effect of ETL thickness on the device performance was studied by varying the Alq3 thickness (5 nm, 10 nm and 20 nm) and the device with an ETL thickness of 20 nm was found to exhibit the maximum brightness value of 11 662 cd m(-2) with a maximum luminous efficiency of 4.87 cd A(-1). Further, by using this highly electroluminescent blue PFONPN01 as a host and a narrow band gap, yellow emitting small molecule, dithiophene benzothiadiazole (DBT), as a guest at three different concentrations (0.2%, 0.4% and 0.6%), WPLEDs with the ITO/PEDOT:PSS/emissive layer/Alq3(20 nm)/LiF/Al configuration were fabricated and maximum brightness values of 8025 cd m(-2), 9565 cd m(-2) and 10 180 cd m(-2) were achieved respectively. 0.4% DBT in PFONPN01 was found to give white light with Commission International de l'Echairage (CIE) coordinates of (0.31, 0.38), a maximum luminous efficiency of 6.54 cd A(-1) and a color-rendering index (CRI) value of 70.

Influence of high hydrostatic pressure on Alq3, Gaq3, and Inq3 (q = 8-hydroxyquinoline).

PubMed

Hernández, Ignacio; Gillin, William P

2009-10-29

We have studied the spectroscopic properties of OLED materials Alq(3), Gaq(3) and Inq(3) (q = 8-hydroxyquinoline) under pressure. We discuss the results in terms of the influence of structural modifications, the isomeric state and the enhancement of the intermolecular interaction. As-grown Alq(3), Gaq(3), Inq(3) containing meridional (mer) isomer experience a red shift of nearly 90 nm (2400 cm(-1)) in the 0-8 GPa range. Abrupt changes in the photoluminescence occur during compression at intermediate pressures for all materials. We assign them to a phase transition, its critical pressure depending on the central cation. All three samples experience an amorphization at P approximately 6 GPa, with associated changes in the spectroscopic properties. The pressure-induced phase transitions present hysteresis to ambient conditions. Photoluminescence lifetime decreases in all cases in the explored pressure range. In the case of facial isomer containing polymorphs of Alq(3), luminescence does not change its energy significantly. The most significant spectroscopic change observed in fac-isomer containing materials corresponds to gamma-Alq(3), which presents a low energy component that gains relative importance when pressure is increased. We ascribe this phenomenon to the presence of sensitized mer isomer impurities.

Influence of electron transport layer thickness on optical properties of organic light-emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Guohong; Liu, Yong; Li, Baojun

2015-06-07

We investigate experimentally and theoretically the influence of electron transport layer (ETL) thickness on properties of typical N,N′-diphenyl-N,N′-bis(1-naphthyl)-[1,1′-biphthyl]-4,4′-diamine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq{sub 3}) heterojunction based organic light-emitting diodes (OLEDs), where the thickness of ETL is varied to adjust the distance between the emitting zone and the metal electrode. The devices showed a maximum current efficiency of 3.8 cd/A when the ETL thickness is around 50 nm corresponding to an emitter-cathode distance of 80 nm, and a second maximum current efficiency of 2.6 cd/A when the ETL thickness is around 210 nm corresponding to an emitter-cathode distance of 240 nm. We adopt a rigorous electromagnetic approach that takesmore » parameters, such as dipole orientation, polarization, light emitting angle, exciton recombination zone, and diffusion length into account to model the optical properties of devices as a function of varying ETL thickness. Our simulation results are accurately consistent with the experimental results with a widely varying thickness of ETL, indicating that the theoretical model may be helpful to design high efficiency OLEDs.« less

Direct observation of conductive filament formation in Alq3 based organic resistive memories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Busby, Y., E-mail: yan.busby@unamur.be; Pireaux, J.-J.; Nau, S.

2015-08-21

This work explores resistive switching mechanisms in non-volatile organic memory devices based on tris(8-hydroxyquinolie)aluminum (Alq{sub 3}). Advanced characterization tools are applied to investigate metal diffusion in ITO/Alq{sub 3}/Ag memory device stacks leading to conductive filament formation. The morphology of Alq{sub 3}/Ag layers as a function of the metal evaporation conditions is studied by X-ray reflectivity, while depth profile analysis with X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry is applied to characterize operational memory elements displaying reliable bistable current-voltage characteristics. 3D images of the distribution of silver inside the organic layer clearly point towards the existence of conductive filamentsmore » and allow for the identification of the initial filament formation and inactivation mechanisms during switching of the device. Initial filament formation is suggested to be driven by field assisted diffusion of silver from abundant structures formed during the top electrode evaporation, whereas thermochemical effects lead to local filament inactivation.« less

Spin-dependent transport behavior in C{sub 60} and Alq{sub 3} based spin valves with a magnetite electrode (invited)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Xianmin, E-mail: xmzhang@wpi-aimr.tohoku.ac.jp; Mizukami, Shigemi; Ma, Qinli

2014-05-07

The spin-dependent transport behavior in organic semiconductors (OSs) is generally observed at low temperatures, which likely results from poor spin injection efficiency at room temperature from the ferromagnetic metal electrodes to the OS layer. Possible reasons for this are the low Curie temperature and/or the small spin polarization efficiency for the ferromagnetic electrodes used in these devices. Magnetite has potential as an advanced candidate for use as the electrode in spintronic devices, because it can achieve 100% spin polarization efficiency in theory, and has a high Curie temperature (850 K). Here, we fabricated two types of organic spin valves using magnetitemore » as a high efficiency electrode. C{sub 60} and 8-hydroxyquinoline aluminum (Alq{sub 3}) were employed as the OS layers. Magnetoresistance ratios of around 8% and over 6% were obtained in C{sub 60} and Alq{sub 3}-based spin valves at room temperature, respectively, which are two of the highest magnetoresistance ratios in organic spin valves reported thus far. The magnetoresistance effect was systemically investigated by varying the thickness of the Alq{sub 3} layer. Moreover, the temperature dependence of the magnetoresistance ratios for C{sub 60} and Alq{sub 3}-based spin valves were evaluated to gain insight into the spin-dependent transport behavior. This study provides a useful method in designing organic spin devices operated at room temperature.« less

Precipitation of thin-film organic single crystals by a novel crystal growth method using electrospray and ionic liquid film

NASA Astrophysics Data System (ADS)

Ueda, Hiroyuki; Takeuchi, Keita; Kikuchi, Akihiko

2018-04-01

We report an organic single crystal growth technique, which uses a nonvolatile liquid thin film as a crystal growth field and supplies fine droplets containing solute from the surface of the liquid thin film uniformly and continuously by electrospray deposition. Here, we investigated the relationships between the solute concentration of the supplied solution and the morphology and size of precipitated crystals for four types of fluorescent organic low molecule material [tris(8-hydroxyquinoline)aluminum (Alq3), 2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD), N,N‧-bis(3-methylphenyl)-N,N‧-diphenylbenzidine (TPD), and N,N-bis(naphthalene-1-yl)-N,N-diphenyl-benzidine (NPB)] using an ionic liquid as the nonvolatile liquid. As the concentration of the supplied solution decreased, the morphology of precipitated crystals changed from dendritic or leaf shape to platelike one. At the solution concentration of 0.1 mg/ml, relatively large platelike single crystals with a diagonal length of over 100 µm were obtained for all types of material. In the experiment using ionic liquid and dioctyl sebacate as nonvolatile liquids, it was confirmed that there is a clear positive correlation between the maximum volume of the precipitated single crystal and the solubility of solute under the same solution supply conditions.

Effects of electron transport material on blue organ light-emitting diode with fluorescent dopant of BCzVBi.

PubMed

Meng, Mei; Song, Wook; Kim, You-Hyun; Lee, Sang-Youn; Jhun, Chul-Gyu; Zhu, Fu Rong; Ryu, Dae Hyun; Kim, Woo-Young

2013-01-01

High efficiency blue organic light emitting diodes (OLEDs), based on 2-me-thyl-9,10-di(2-naphthyl) anthracene (MADN) doped with 4,4'-bis(9-ethyl-3-carbazovinylene)-1,1'-biphenyl (BCzVBi), were fabricated using two different electron transport layers (ETLs) of tris(8-hydroxyquinolino)-aluminum (Alq3) and 4,7-di-phenyl-1,10-phenanthroline (Bphen). Bphen ETL layers favored the efficient hole-electron recombination in the emissive layer of the BCzVBi-doped blue OLEDs, leading to high luminous efficiency and quantum efficiency of 8.34 cd/A at 100 mA/cm2 and 5.73% at 100 cd/m2, respectively. Maximum luminance of blue OLED with Bphen ETL and Alq3 ETL were 10670 cd/m2, and CIExy coordinates of blue OLEDs were (0.180, 0279) and (0.155, 0.212) at 100 cd/m2.

Degradation in organic light emitting devices

NASA Astrophysics Data System (ADS)

Dinh, Vincent Vinh

This thesis is about the fundamental causes of degradation in tris(8-Hydroxyquinoline) Aluminum (Alq3)-based organic light emitting diodes (OLEDs). Degradation typically occurs when a current is forced through an insulating material. Since the insulator does not support conduction waves (in its ground state), chemical restructuring must occur to accommodate the current. OLEDs have many technical advantages over the well known semiconductor-based light emitting diodes (LEDs). OLEDs have quantum efficiencies ˜1% (˜10 times higher than the LEDs), and operational power thresholds ˜.05mW (˜100 lower than the LEDs). OLEDs are preferred in power limited and portable devices; devices such as laptops and displays consume ˜1/4 of the supplied power---any power saving is significant. Other advantages, like better compliance to curved surfaces and ease of fabrication, give the OLEDs an even greater edge over the LEDs. OLEDs must have at least comparable or better lifetimes to remain attractive. Typical OLEDs last several 100hrs compared to the several 1000hrs for the LEDs. For reliable OLED application, it is necessary to understand the above breakdown mechanism. In this thesis, we attempt to understand the breakdown by looking at how OLEDs are made, how they work, and when they don't. In the opening sections, we give an overview of OLEDs and LEDs, especially how sustained luminescence is achieved through current circulation. Then in Chapter 2, we look at the basic components in the OLEDs. In Chapter 3 we look at how a hole material (like poly-vinyl carbazole or PVK) establishes an excitonic environment for the sustained luminescence in Alq3. We then approximate how potential is distributed when a simple luminescence system is in operation. In Chapter 4, we look at ways of measuring this distribution via the OLED impedance. Finally in Chapter 5, we look at the OLED stability under light emission conditions via PVK and Alq3 photoemission and photoabsorption spectra. Implicit throughout our study, we assume that regions of high electric field will likely induce chemical changes and hence breakdown in the OLED. Our electrical measurements suggest that at least 6% of the applied potential may be concentrated at the interfaces. Spectroscopic measurements suggest that chemical reaction does occur there (namely the electrode/Alq3 interface), thus leading to device failure and suggest a course of action to avoid this fate with other OLED systems.

Study of voltage decrease in organic light emitting diodes during the initial stage of lifetime

NASA Astrophysics Data System (ADS)

Cusumano, P.

2016-02-01

We report the results of lifetime DC testing at constant current of not-encapsulated organic light emitting diodes (OLEDs) based on Tris (8 idroxyquinoline) aluminum (Alq3) as emitting material. In particular, a voltage decrease during the initial stage of the lifetime test is observed. The cause of this behavior is also discussed, mainly linked to initial Joule self-heating of the device, rising its temperature above room temperature until thermal equilibrium is reached at steady state.

Permanent polarization and charge distribution in organic light-emitting diodes (OLEDs): Insights from near-infrared charge-modulation spectroscopy of an operating OLED

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marchetti, Alfred P.; Haskins, Terri L.; Young, Ralph H.

2014-03-21

Vapor-deposited Alq{sub 3} layers typically possess a strong permanent electrical polarization, whereas NPB layers do not. (Alq{sub 3} is tris(8-quinolinolato)aluminum(III); NPB is 4,4′-bis[N-(1-naphthyl)-N-phenylamino]biphenyl.) The cause is a net orientation of the Alq{sub 3} molecules with their large dipole moments. Here we report on consequences for an organic light-emitting diode (OLED) with an NPB hole-transport layer and Alq{sub 3} electron-transport layer. The discontinuous polarization at the NPB|Alq{sub 3} interface has the same effect as a sheet of immobile negative charge there. It is more than compensated by a large concentration of injected holes (NPB{sup +}) when the OLED is running. Wemore » discuss the implications and consequences for the quantum efficiency and the drive voltage of this OLED and others. We also speculate on possible consequences of permanent polarization in organic photovoltaic devices. The concentration of NPB{sup +} was measured by charge-modulation spectroscopy (CMS) in the near infrared, where the NPB{sup +} has a strong absorption band, supplemented by differential-capacitance and current-voltage measurements. Unlike CMS in the visible, this method avoids complications from modulation of the electroluminescence and electroabsorption.« less

Luminescent hybrid materials based on (8-hydroxyquinoline)-substituted metal-organic complexes and lead-borate glasses

NASA Astrophysics Data System (ADS)

Petrova, Olga B.; Anurova, Maria O.; Akkuzina, Alina A.; Saifutyarov, Rasim R.; Ermolaeva, Ekaterina V.; Avetisov, Roman I.; Khomyakov, Andrew V.; Taydakov, Ilya V.; Avetissov, Igor Ch.

2017-07-01

Novel luminescent organic-inorganic hybrid materials based on 8-hydroxyquinoline metal complexes (Liq, Kq, Naq, Rbq, Mgq2, Srq2, Znq2, Scq3, Alq3, Gaq3, and Inq3) have been synthesized by a high temperature exchange reaction with 80PbF2-20B2O3 inorganic low-melting glass. The mechanical and optical properties, transmission spectra, emission an excitation photoluminescence, and luminescence kinetic of hybrid materials were studied. All hybrid materials showed a wide luminescence band in the range 400-700 nm.

Effect of the nozzle tip’s geometrical shape on electrospray deposition of organic thin films

NASA Astrophysics Data System (ADS)

Ueda, Hiroyuki; Takeuchi, Keita; Kikuchi, Akihiko

2017-04-01

Electrospray deposition (ESD) is a favorable wet fabrication technique for organic thin films. We investigated the effects of the nozzle tip’s geometrical shape on the spraying properties of an organic solution used for ESD. Five types of cylindrical metal nozzles with zero (flat end) to four protrusions at the tips were prepared for depositing a solution of a small-molecule compound, tris(8-hydroxyquinolinato)aluminum (Alq3) solution. We confirmed that the diameter of the deposited droplets and their size dispersion decreased with an increase in the number of protrusions. The area occupation ratio of small droplets with a diameter smaller than 2 µm increased from 21 to 83% as the number of protrusions was increased from zero to four. The surface roughness root mean square of 60-nm-thick Alq3 films substantially improved from 32.5 to 6.8 nm with increasing number of protrusions.

Optical and electrical properties of TiOPc doped Alq3 thin films

NASA Astrophysics Data System (ADS)

Ramar, M.; Suman, C. K.; Tyagi, Priyanka; Srivastava, R.

2015-06-01

The Titanyl phthalocyanine (TiOPc) was doped in Tris (8-hydroxyquinolinato) aluminum (Alq3) with different concentration. The thin film of optimized doping concentration was studied extensively for optical and electrical properties. The optical properties, studied using ellipsometry, absorption and photoluminescence. The absorption peak of Alq3 and TiOPc was observed at 387 nm and 707 nm and the photo-luminescence intensity (PL) peak of doped thin film was observed at 517 nm. The DC and AC electrical properties of the thin film were studied by current density-voltage (J-V) characteristics and impedance over a frequency range of 100 Hz - 1 MHz. The electron mobility calculated from trap-free space-charge limited region (SCLC) is 0.17×10-5 cm2/Vs. The Cole-Cole plots shows that the TiOPc doped Alq3 thin film can be represented by a single parallel resistance RP and capacitance CP network with a series resistance RS (10 Ω). The value of RP and CP at zero bias was 1587 Ω and 2.568 nF respectively. The resistance RP decreases with applied bias whereas the capacitance CP remains almost constant.

The drift-diffusion interpretation of the electron current within the organic semiconductor characterized by the bulk single energy trap level

NASA Astrophysics Data System (ADS)

Cvikl, B.

2010-01-01

The closed solution for the internal electric field and the total charge density derived in the drift-diffusion approximation for the model of a single layer organic semiconductor structure characterized by the bulk shallow single trap-charge energy level is presented. The solutions for two examples of electric field boundary conditions are tested on room temperature current density-voltage data of the electron conducting aluminum/tris(8-hydroxyquinoline aluminum/calcium structure [W. Brütting et al., Synth. Met. 122, 99 (2001)] for which jexp∝Va3.4, within the interval of bias 0.4 V≤Va≤7. In each case investigated the apparent electron mobility determined at given bias is distributed within a given, finite interval of values. The bias dependence of the logarithm of their lower limit, i.e., their minimum values, is found to be in each case, to a good approximation, proportional to the square root of the applied electric field. On account of the bias dependence as incorporated in the minimum value of the apparent electron mobility the spatial distribution of the organic bulk electric field as well as the total charge density turn out to be bias independent. The first case investigated is based on the boundary condition of zero electric field at the electron injection interface. It is shown that for minimum valued apparent mobilities, the strong but finite accumulation of electrons close to the anode is obtained, which characterize the inverted space charge limited current (SCLC) effect. The second example refers to the internal electric field allowing for self-adjustment of its boundary values. The total electron charge density is than found typically to be of U shape, which may, depending on the parameters, peak at both or at either Alq3 boundary. It is this example in which the proper SCLC effect is consequently predicted. In each of the above two cases, the calculations predict the minimum values of the electron apparent mobility, which substantially exceed the corresponding published measurements. For this reason the effect of the drift term alone is additionally investigated. On the basis of the published empirical electron mobilities and the diffusion term revoked, it is shown that the steady state electron current density within the Al/Alq3 (97 nm)/Ca single layer organic structure may well be pictured within the drift-only interpretation of the charge carriers within the Alq3 organic characterized by the single (shallow) trap energy level. In order to arrive at this result, it is necessary that the nonzero electric field, calculated to exist at the electron injecting Alq3/Ca boundary, is to be appropriately accounted for in the computation.

Tuning Interfacial States Using Organic Molecules as Spin Filters

NASA Astrophysics Data System (ADS)

Deloach, Andrew; Wang, Jingying; Papa, Christopher M.; Myahkostupov, Mykhaylo; Castellano, Felix N.; Dougherty, Daniel B.; Jiang, Wei; Liu, Feng

Organic semiconductors are known to have long spin relaxation times which makes them a good candidate for spintronics. However, an issue with these materials is that at metal-organic interfaces there is a conductivity mismatch problem that suppresses spin injection. To overcome this, orbital mixing at the interface can be tuned with an organic spacer layer to promote the formation of spin polarized interface states. These states act as a ``spin filters'' and have been proposed as an explanation for the large tunneling magnetoresistance seen in devices using tris-(8-hydroxyquinolate)-aluminum(Alq3). Here, we show that the spin polarized interface states can be tuned from metallic to resistive by subtle changes in molecular orbitals. This is done using spin polarized scanning tunneling microscopy with three different tris-(8-hydroxyquinolate) compounds: aluminum, chromium, and iron. Differences in d-orbital mixing results in different mechanisms of interfacial coupling, giving rise to metallic or resistive interface states. Supported by the U.S. DoE award No. DE-SC0010324.

Transport and recombination in organic light-emitting diodes studied by electrically detected magnetic resonance.

PubMed

Graeff, C F O; Silva, G B; Nüesch, F; Zuppiroli, L

2005-09-01

We have used electrically detected magnetic resonance (EDMR) to study a series of multilayer organic devices based on aluminum (III) 8-hydroxyquinoline (Alq3). These devices were designed to identify the microscopic origin of different spin-dependent processes, i.e. hopping and exciton formation. The EDMR signal in organic light-emitting diodes (OLEDs) based on Alq3 is only observed when the device is electroluminescent and is assigned to spin-dependent exciton formation. It can be decomposed in at least two Gaussians: one with peak-to-peak line (deltaH(PP)) of 1.6 mT and another with deltaH(PP) of 2.0 to 3.4 mT, depending on bias and temperature. The g-factors of the two components are barely distinguishable and close to 2.003. The broad line is attributed to the resonance in Alq3 anions, while the other line is attributed to cationic states. These attributions are supported by line shape and its electrical-field dependence of unipolar Alq3-based diodes, where hopping process related to dication and dianion formation is observed. In these unipolar devices, it is shown that the signal coming from spin-dependent hopping occurs close to organic semiconductor/metal interfaces. The sign of the magnetic-resonance-induced conductivity change is dominated by charge injection rather than charge mobility. Our results indicate that the probability of singlet exciton formation in our OLEDs is smaller than 25%.

Effect of trapped electrons on the transient current density and luminance of organic light-emitting diode

NASA Astrophysics Data System (ADS)

Lee, Jiun-Haw; Chen, Chia-Hsun; Lin, Bo-Yen; Shih, Yen-Chen; Lin, King-Fu; Wang, Leeyih; Chiu, Tien-Lung; Lin, Chi-Feng

2018-04-01

Transient current density and luminance from an organic light-emitting diode (OLED) driven by voltage pulses were investigated. Waveforms with different repetition rate, duty cycle, off-period, and on-period were used to study the injection and transport characteristics of electron and holes in an OLED under pulse operation. It was found that trapped electrons inside the emitting layer (EML) and the electron transporting layer (ETL) material, tris(8-hydroxyquinolate)aluminum (Alq3) helped for attracting the holes into the EML/ETL and reducing the driving voltage, which was further confirmed from the analysis of capacitance-voltage and displacement current measurement. The relaxation time and trapped filling time of the trapped electrons in Alq3 layer were ~200 µs and ~600 µs with 6 V pulse operation, respectively.

Effect of encapsulation technology on organic light emitting diode lifetime

NASA Astrophysics Data System (ADS)

Zhong, Jian; Gao, Zhuo; Gao, Juan; Dai, Ke; Chen, Jiule

2012-03-01

A kind of green organic light-emitting diodes (OLED) was prepared via vacuum thermal evaporation, of which the multilayer structure was indium-tin oxide (ITO)/copper-phthalocyanine (CuPc) (200 Å)/ N,N'-bis(1-naphthyl)- N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine ( α-NPD) (600 Å)/ N'-diphenyl- N,N'-tris(8-hydroxyquinoline) aluminium (Alq3) (400 Å):10-(2-benzothiazolyl)-1,1,7,7-tetramethyl-2,3,6,7-tetrahydro-1 H,5 H,11 H-(l)benzopyropyrano(6,7,8- i, j)quinolizin-11-one (C545T) (2%)/Alq3 (200 Å)/LiF (10 Å)/Al (1000 Å). And we used both traditional glass encapsulation and thin film encapsulation (TFE) technologies to protect the device, reducing impact of vapor and oxygen. Organic film offered an excellent surface morphology, while inorganic film was nearly a perfect barrier to vapor and oxygen. Both of them constituted the encapsulation unit of TFE. According to the results of acceleration life test, the operation lifetime of device using TFE was 22% less than that of device using traditional glass cap encapsulation. So, the technology of TFE should be optimized further, and the quality of TFE needs a great improvement. There is a long way to go and a lot of hard work before realizing flexible display with OLED, but the dream will be true one day.

Hydroxynaphthyridine-derived group III metal chelates: wide band gap and deep blue analogues of green Alq3 (tris(8-hydroxyquinolate)aluminum) and their versatile applications for organic light-emitting diodes.

PubMed

Liao, Szu-Hung; Shiu, Jin-Ruei; Liu, Shun-Wei; Yeh, Shi-Jay; Chen, Yu-Hung; Chen, Chin-Ti; Chow, Tahsin J; Wu, Chih-I

2009-01-21

A series of group III metal chelates have been synthesized and characterized for the versatile application of organic light-emitting diodes (OLEDs). These metal chelates are based on 4-hydroxy-1,5-naphthyridine derivates as chelating ligands, and they are the blue version analogues of well-known green fluorophore Alq(3) (tris(8-hydroxyquinolinato)aluminum). These chelating ligands and their metal chelates were easily prepared with an improved synthetic method, and they were facially purified by a sublimation process, which enables the materials to be readily available in bulk quantity and facilitates their usage in OLEDs. Unlike most currently known blue analogues of Alq(3) or other deep blue materials, metal chelates of 4-hydroxy-1,5-naphthyridine exhibit very deep blue fluorescence, wide band gap energy, high charge carrier mobility, and superior thermal stability. Using a vacuum-thermal-deposition process in the fabrication of OLEDs, we have successfully demonstrated that the application of these unusual hydroxynaphthyridine metal chelates can be very versatile and effective. First, we have solved or alleviated the problem of exciplex formation that took place between the hole-transporting layer and hydroxynaphthyridine metal chelates, of which OLED application has been prohibited to date. Second, these deep blue materials can play various roles in OLED application. They can be a highly efficient nondopant deep blue emitter: maximum external quantum efficiency eta(ext) of 4.2%; Commision Internationale de L'Eclairage x, y coordinates, CIE(x,y) = 0.15, 0.07. Compared with Alq(3), Bebq(2) (beryllium bis(benzoquinolin-10-olate)), or TPBI (2,2',2''-(1,3,5-phenylene)tris(1-phenyl-1H-benzimidazole), they are a good electron-transporting material: low HOMO energy level of 6.4-6.5 eV and not so high LUMO energy level of 3.0-3.3 eV. They can be ambipolar and possess a high electron mobility of 10(-4) cm(2)/V s at an electric field of 6.4 x 10(5) V/cm. They are a qualified wide band gap host material for efficient blue perylene (CIE(x,y) = 0.14, 0.17 and maximum eta(ext) 3.8%) or deep blue 9,10-diphenylanthracene (CIE(x,y) = 0.15, 0.06 and maximum eta(ext) 2.8%). For solid state lighting application, they are desirable as a host material for yellow dopant (rubrene) in achieving high efficiency (eta(ext) 4.3% and eta(P) 8.7 lm/W at an electroluminance of 100 cd/m(2) or eta(ext) 3.9% and eta(P) 5.1 lm/W at an electroluminance of 1000 cd/m(2)) white electroluminescence (CIE(x,y) = 0.30, 0.35).

Structural Dynamics in Metal Tris-hydroxyquinolines: Interconversion of Meridianal and Facial Alq3 Isomers

NASA Astrophysics Data System (ADS)

Ferris, Kim; Sapochak, Linda; Burrows, Paul; Rodovsky, Deanna; Marmolejo, Theresa

2004-03-01

While previous work investigating the charge transport properties of Alq3 has indicated that the meridianal (mer) conformation of Alq3 is predominant species, recent work suggesting identification of a facial (fac) form raises again the question of heterogeneity. Electronic structure computations from our group have noted that the energy difference(in parenthesis) between the mer and fac conformations is highly sensitive to basis set description (8.6 kcal/mol//3-21g*/SCF; 6.9 kcal/mol//6-31g*/SCF), electron correlation (6.0 kcal/mol//3-21g*/MP2; 4.7 kcal/mol//6-31g*/MP2), and solvent effects (4.4 kcal/mol/3-21g*/SCF/DMSO). Given these small energy differences, we have conducted a series of Hartree-Fock and first principles electronic structure computations on the interconversion of these structural forms, and will report on the structural and energetic aspects of the transformation. The likely reaction path involves lengthening of the Al-N bond to the point where a pentacoordinate intermediate or transition state would be formed, followed by flipping of the ligand through rotation around the Al-O bond. Following Schmidbauer's earlier work, we note that transformation involving only one ligand will actually lead to a facial isomer. Preliminary characterization of this transition state suggests that the activation energy is approximately 20-25 kcal/mol above the mer conformation. The authors gratefully acknowledge financial support from PNNL Laboratory Directed Research and Development Project and the U.S. Department of Energy, Office of Science, Materials Sciences Division.

The effects of ultra-thin cerium fluoride film as the anode buffer layer on the electrical characteristics of organic light emitting diodes

NASA Astrophysics Data System (ADS)

Lu, Hsin-Wei; Tsai, Cheng-Che; Hong, Cheng-Shong; Kao, Po-Ching; Juang, Yung-Der; Chu, Sheng-Yuan

2016-11-01

In this study, the efficiency of organic light-emitting diodes (OLEDs) was enhanced by depositing a CeF3film as an ultra-thin buffer layer between the indium tin oxide (ITO) electrode and α-naphthylphenylbiphenyldiamine (NPB) hole transport layer, with the structure configuration ITO/CeF3 (0.5, 1, and 1.5 nm)/α-naphthylphenylbiphenyl diamine (NPB) (40 nm)/tris(8-hydroxyquinoline) aluminum (Alq3) (60 nm)/lithium fluoride (LiF) (1 nm)/Al (150 nm). The enhancement mechanism was systematically investigated via several approaches. The X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy results revealed the formation of the UV-ozone treated CeF3 film. The work function increased from 4.8 eV (standard ITO electrode) to 5.22 eV (0.5-nm-thick UV-ozone treated CeF3 film deposited on the ITO electrode). The surface roughness of the UV-ozone treated CeF3 film was smoother than that of the standard ITO electrode. Further, the UV-ozone treated CeF3 film increased both the surface energy and polarity, as determined from contact angle measurements. In addition, admittance spectroscopy measurements showed an increased capacitance and conductance of the OLEDs. Accordingly, the turn-on voltage decreased from 4.2 V to 3.6 V at 1 mA/cm2, the luminance increased from 7588 cd/m2 to 24760 cd/m2, and the current efficiency increased from 3.2 cd/A to 3.8 cd/A when the 0.5-nm-thick UV-ozone treated CeF3 film was inserted into the OLEDs.

Degradation of small-molecule organic solar cells

NASA Astrophysics Data System (ADS)

Song, Q. L.; Wang, M. L.; Obbard, E. G.; Sun, X. Y.; Ding, X. M.; Hou, X. Y.; Li, C. M.

2006-12-01

Small-molecule organic solar cells with a structure of indium tin oxide (ITO)tris-8-hydroxy-quinolinato aluminum (Alq3) (2nm)fullerene (C60) (40nm)\\copper phthalocyanine (CuPc) (32nm)Au (40nm) were fabricated. The shelf lifetime of unencapsulated devices was over 1500h, and the power conversion efficiency reached 0.76% under AM1.5G (air mass 1.5 global) 75mW/cm2. The long lifetime was attributed to the inverted structure compared to the conventional ITO CuPcC60bufferAl structure since the former could effectively protect C60 from the diffusion of oxygen and modify interfacial electrical properties. The introduction of a 2nm Alq3 layer into the cells enhanced the power conversion efficiency by more than 20 times. The presence of the thin Alq3 film on the ITO substrate lowered the substrate work function and hence increased the electric field in the organic layers, which was beneficial to the collection of free carriers. The reasons for the degradation of such kind of organic solar cells are analyzed in detail.

Manipulation and control of the interfacial polarization in organic light-emitting diodes by dipolar doping

NASA Astrophysics Data System (ADS)

Jäger, Lars; Schmidt, Tobias D.; Brütting, Wolfgang

2016-09-01

Most of the commonly used electron transporting materials in organic light-emitting diodes exhibit interfacial polarization resulting from partially aligned permanent dipole moments of the molecules. This property modifies the internal electric field distribution of the device and therefore enables an earlier flat band condition for the hole transporting side, leading to improved charge carrier injection. Recently, this phenomenon was studied with regard to different materials and degradation effects, however, so far the influence of dilution has not been investigated. In this paper we focus on dipolar doping of the hole transporting material 4,4-bis[N-(1-naphthyl)-N-phenylamino]-biphenyl (NPB) with the polar electron transporting material tris-(8-hydroxyquinolate) aluminum (Alq3). Impedance spectroscopy reveals that changes of the hole injection voltage do not scale in a simple linear fashion with the effective thickness of the doped layer. In fact, the measured interfacial polarization reaches a maximum value for a 1:1 blend. Taking the permanent dipole moment of Alq3 into account, an increasing degree of dipole alignment is found for decreasing Alq3 concentration. This observation can be explained by the competition between dipole-dipole interactions leading to dimerization and the driving force for vertical orientation of Alq3 dipoles at the surface of the NPB layer.

Supramolecular structures and assembly and luminescent properties of quinacridone derivatives.

PubMed

Ye, Kaiqi; Wang, Jia; Sun, Hui; Liu, Yu; Mu, Zhongcheng; Li, Fei; Jiang, Shimei; Zhang, Jingying; Zhang, Hongxing; Wang, Yue; Che, Chi-Ming

2005-04-28

The synthesis and single-crystal X-ray structures of two quinacridone derivatives, N,N'-di(n-butyl)quinacridone (1) and N,N'-di(n-butyl)-1,3,8,10-tetramethylquinacridone (2), are reported, and the 1H NMR, absorption, photoluminescent (PL), and electroluminescent (EL) characteristics are presented. Both these crystal structures are characterized by intermolecular pi...pi and hydrogen bonding interactions. The intermolecular pi...pi interactions lead to the formation of molecular columns in the solids of 1 and 2, and the interplanar contact distances between two adjacent molecules are 3.48 and 3.55 angstroms, respectively. Crystals of 1 display shorter intermolecular pi...pi contacts and higher density than 2. These results suggest that tighter intermolecular interactions exist in 1. The 1H NMR, absorption, and PL spectra of 1 and 2 in solutions exhibit concentration-dependent properties. The PL quantum yields of 1 in solutions decrease more quickly with the increase of concentration compared to that of 2 in solutions. For solid thin films of Alq3:1 (Alq3 = tris(8-hydroxyquinolinato)aluminum), emission intensities dramatically decrease and obvious red shifts are observed when the dopant concentration is above 4.2%, while for films of Alq3:2, a similar phenomenon occurs when the concentration is above 6.7%. EL devices with Alq3:1 as emitting layer only show high efficiencies (20.3-14.5 cd/A) within the narrow dopant concentration range of 0.5-1.0%. In contrast, high efficiencies (21.5-12.0 cd/A) are achieved for a wider dopant concentration range of 0.5-5.0% when Alq3:2 films are employed as emitting layer. The different PL and EL concentration-dependent properties of the solid thin films Alq3:1 and Alq3:2 are attributed to their different molecular packing characteristics in the solid state.

Charge transfer and injection barrier at the metal-organic interfaces

NASA Astrophysics Data System (ADS)

Yan, Li

2002-09-01

The metal-organic interface plays a critical role in determining the functionality and performance of many innovative organic based devices. It has attracted extensive research interests in recent years. This thesis presents investigations of the electronic structures of organic materials, such as tris-(8-hydroxyquinoline) aluminum (Alq3) and copper phthalocyanine (CuPc), during their interface formation with metals. The characterization is accomplished by X-ray and ultraviolet photoelectron spectroscopes (XPS and UPS) and inverse photoelectron spectroscopy (IPES). As discussed herein, both occupied and unoccupied electronic states at the interfaces are carefully examined in different aspects. In Chapter 4, the charge transfer and chemical reaction at various metal/Alq3 interfaces are investigated using XPS and UPS to study the electron injection into the Alga film. Electron transfer from the low work function metal and Al/LiF(CsF) bilayer to the Alga has been observed. The role of the dielectric and possible chemistry at the interface are discussed in comparison of the low work function metals. Further in Chapter 5, the origin of the metal-interface dipole and the estimation of charge injection barrier is explored using several organic materials. A thermodynamic equilibrium model is extended to explain the relation between the charge transfer process ad the interface dipole. Further, in Chapter 6 the combination of XPS, UPS and IPES detailed the evolution of both occupied and unoccupied energy states during the alkali metal doping. The energy gap modification in organic due to metal doping is observed directly for the spectra. Chapter 7 provides stability study of the organic thin films under x-ray and UV light. The results verify the usability of UPS and XPS for the organic materials used in the thesis. Chapter 7 also shows the secondary ion mass spectroscopy results of metal diffusion in organic thin films.

Controlled manipulation of the Co-Alq3 interface by rational design of Alq3 derivatives.

PubMed

Großmann, Nicolas; Magri, Andrea; Laux, Martin; Stadtmüller, Benjamin; Thielen, Philip; Schäfer, Bernhard; Fuhr, Olaf; Ruben, Mario; Cinchetti, Mirko; Aeschlimann, Martin

2016-11-15

Recently, research has revealed that molecules can be used to steer the local spin properties of ferromagnetic surfaces. One possibility to manipulate ferromagnetic-metal-molecule interfaces in a controlled way is to synthesize specific, non-magnetic molecules to obtain a desired interaction with the ferromagnetic substrate. Here, we have synthesized derivatives of the well-known semiconductor Alq 3 (with q = 8-hydroxyquinolinate), in which the 8-hydroxyquinolinate ligands are partially or completely replaced by similar ligands bearing O- or N-donor sets. The goal of this study was to investigate how the presence of (i) different donor atom sets and (ii) aromaticity in different conjugated π-systems influences the spin properties of the metal-molecule interface formed with a Co(100) surface. The spin-dependent metal-molecule-interface properties have been measured by spin-resolved photoemission spectroscopy, backed up by DFT calculations. Overall, our results show that, in the case of the Co-molecule interface, chemical synthesis of organic ligands leads to specific electronic properties of the interface, such as exciton formation or highly spin-polarized interface states. We find that these properties are even additive, i.e. they can be engineered into one single molecular system that incorporates all the relevant ligands.

Efficient implementation of core-excitation Bethe-Salpeter equation calculations

NASA Astrophysics Data System (ADS)

Gilmore, K.; Vinson, John; Shirley, E. L.; Prendergast, D.; Pemmaraju, C. D.; Kas, J. J.; Vila, F. D.; Rehr, J. J.

2015-12-01

We present an efficient implementation of the Bethe-Salpeter equation (BSE) method for obtaining core-level spectra including X-ray absorption (XAS), X-ray emission (XES), and both resonant and non-resonant inelastic X-ray scattering spectra (N/RIXS). Calculations are based on density functional theory (DFT) electronic structures generated either by ABINIT or QuantumESPRESSO, both plane-wave basis, pseudopotential codes. This electronic structure is improved through the inclusion of a GW self energy. The projector augmented wave technique is used to evaluate transition matrix elements between core-level and band states. Final two-particle scattering states are obtained with the NIST core-level BSE solver (NBSE). We have previously reported this implementation, which we refer to as OCEAN (Obtaining Core Excitations from Ab initio electronic structure and NBSE) (Vinson et al., 2011). Here, we present additional efficiencies that enable us to evaluate spectra for systems ten times larger than previously possible; containing up to a few thousand electrons. These improvements include the implementation of optimal basis functions that reduce the cost of the initial DFT calculations, more complete parallelization of the screening calculation and of the action of the BSE Hamiltonian, and various memory reductions. Scaling is demonstrated on supercells of SrTiO3 and example spectra for the organic light emitting molecule Tris-(8-hydroxyquinoline)aluminum (Alq3) are presented. The ability to perform large-scale spectral calculations is particularly advantageous for investigating dilute or non-periodic systems such as doped materials, amorphous systems, or complex nano-structures.

Resonant infrared laser deposition of polymer-nanocomposite materials for optoelectronic applications

NASA Astrophysics Data System (ADS)

Park, Hee K.; Schriver, Kenneth E.; Haglund, Richard F.

2011-11-01

Polymers find a number of potentially useful applications in optoelectronic devices. These include both active layers, such as light-emitting polymers and hole-transport layers, and passive layers, such as polymer barrier coatings and light-management films. This paper reports the experimental results for polymer films deposited by resonant infrared matrix-assisted pulsed laser evaporation (RIR-MAPLE) and resonant infrared pulsed laser deposition (RIR-PLD) for commercial optoelectronic device applications. In particular, light-management films, such as anti-reflection coatings, require refractive-index engineering of a material. However, refractive indices of polymers fall within a relatively narrow range, leading to major efforts to develop both low- and high-refractive-index polymers. Polymer nanocomposites can expand the range of refractive indices by incorporating low- or high-refractive-index nanoscale materials. RIR-MAPLE is an excellent technique for depositing polymer-nanocomposite films in multilayer structures, which are essential to light-management coatings. In this paper, we report our efforts to engineer the refractive index of a barrier polymer by combining RIR-MAPLE of nanomaterials (for example, high refractive-index TiO2 nanoparticles) and RIR-PLD of host polymer. In addition, we report on the properties of organic and polymer films deposited by RIR-MAPLE and/or RIR-PLD, such as Alq3 [tris(8-hydroxyquinoline) aluminum] and PEDOT:PSS [poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate)]. Finally, the challenges and potential for commercializing RIR-MAPLE/PLD, such as industrial scale-up issues, are discussed.

Assembling photoluminescent tri(8-quinolinolato)aluminum into periodic mesoporous organosilicas.

PubMed

Yang, Ying; Zhang, Xin; Kan, Qiubin

2013-12-01

Mesostructured and mesoporous materials are emerging as a new class of optical materials. However, their synthesis is nontrivial. In this work, periodic mesostructured metal complex-containing silicas of MCM- and SBA-type bearing homogeneously distributed photoluminescent tri(8-quinolinolato)aluminum inside the channel walls (denoted as Alq3@PMO-MCM and Alq3@PMO-SBA, respectively) have been achieved via one-pot co-assembling of inorganic/surfactant/optically active species. A comprehensive multianalytical characterization of the structural and optical properties demonstrates that both Alq3@PMO-MCM and Alq3@PMO-SBA series gainfully combine the photoluminescent properties of Alq3 with the porous features of PMOs. Regularly arranged pores provide high surface area to disperse optically active components well and render Alq3-containing PMOs promising materials for optoelectronic applications. Copyright © 2013. Published by Elsevier Inc.

Experimental analysis of dark frame growth mechanism in organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Minagawa, Masahiro; Tanabe, Takuma; Kondo, Eiki; Kamimura, Kenji; Kimura, Munehiro

2018-02-01

Organic light-emitting diodes (OLEDs) were fabricated with heterojunction interfaces and layers that were prepared by cold isostatic pressing (CIP), and the growth characteristics of their non-emission areas, or dark frames (D/Fs), were investigated during storage. We fabricated an OLED with an indium-tin-oxide (ITO)/N,N‧-di(1-naphthyl)-N,N‧-diphenyl-(1,1‧-biphenyl)-4,4‧-diamine (α-NPD)/tris(8-hydroxylquinoline)aluminum (Alq3)/LiF/Al structure without CIP treatment (Device I), as well as OLEDs that were pressed after the deposition of α-NPD (Device II), Alq3 (Device III), and LiF/Al (Device IV) layers. Although Devices I, II, and III showed typical D/F growth characteristics, the D/F growth rate in Device IV was markedly mitigated, indicating that the Alq3/LiF/Al interfaces dominated the D/F growth. Moreover, we found that the electron injection characteristic was poorer in the electron-only device stored after the LiF layer deposition than in that stored before the LiF deposition. Therefore, the decreased electron injection due to storage at the interfaces was attributed to the D/F growth.

Optical and electrical properties of TiOPc doped Alq{sub 3} thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramar, M.; Suman, C. K., E-mail: sumanck@nplindia.org; Tyagi, Priyanka

2015-06-24

The Titanyl phthalocyanine (TiOPc) was doped in Tris (8-hydroxyquinolinato) aluminum (Alq3) with different concentration. The thin film of optimized doping concentration was studied extensively for optical and electrical properties. The optical properties, studied using ellipsometry, absorption and photoluminescence. The absorption peak of Alq{sub 3} and TiOPc was observed at 387 nm and 707 nm and the photo-luminescence intensity (PL) peak of doped thin film was observed at 517 nm. The DC and AC electrical properties of the thin film were studied by current density-voltage (J-V) characteristics and impedance over a frequency range of 100 Hz - 1 MHz. The electron mobility calculated from trap-free space-chargemore » limited region (SCLC) is 0.17×10{sup −5} cm{sup 2}/Vs. The Cole-Cole plots shows that the TiOPc doped Alq{sub 3} thin film can be represented by a single parallel resistance R{sub P} and capacitance C{sub P} network with a series resistance R{sub S} (10 Ω). The value of R{sub P} and C{sub P} at zero bias was 1587 Ω and 2.568 nF respectively. The resistance R{sub P} decreases with applied bias whereas the capacitance C{sub P} remains almost constant.« less

Tunable organic distributed feedback dye laser device excited through Förster mechanism

NASA Astrophysics Data System (ADS)

Tsutsumi, Naoto; Hinode, Taiki

2017-03-01

Tunable organic distributed feedback (DFB) dye laser performances are re-investigated and characterized. The slab-type waveguide DFB device consists of air/active layer/glass substrate. Active layer consisted of tris(8-quinolinolato)aluminum (Alq3), 4-(dicyanomethylene)-2-methyl-6-(4-dimethylaminostyryl)-4H-pyran (DCM) dye, and polystyrene (PS) matrix. Effective energy transfer from Alq3 to DCM through Förster mechanism enhances the laser emission. Slope efficiency in the range of 4.9 and 10% is observed at pump energy region higher than 0.10-0.15 mJ cm-2 (lower threshold), which is due to the amplified spontaneous emission (ASE) and lasing. Typical slope efficiency for lasing in the range of 2.0 and 3.0% is observed at pump energy region higher than 0.25-0.30 mJ cm-2 (higher threshold). The tuning wavelength for the laser emission is ranged from 620 to 645 nm depending on the ASE region.

Studies of the degradation mechanism of organic light-emitting diodes based on tris(8-quinolinolate)aluminum Alq and 2-tert-butyl-9,10-di(2-naphthyl)anthracene TBADN

NASA Astrophysics Data System (ADS)

Jarikov, Viktor V.; Kondakov, Denis Y.

2009-02-01

Previously, radical cation of tris(8-quinolinolate)aluminum (Alq•+) has been associated with the instability of Alq films subjected to holes-only electrical current. Yet, the questions remain (i) whether Alq•+ is the primary source of the intrinsic degradation of bipolar organic light-emitting diodes (OLEDs) based on Alq, (ii) whether Alq•+ reactions result in deep charge traps in holes-only devices as found in bipolar counterparts, and (iii) whether radical cations can be a common source of degradation of OLEDs irrespective of materials. With regards to generality of hole-current-related degradation, it is interesting to examine the behavior of 9,10-diarylanthracenes (DAAs)—the practically important class of blue-fluorescing light-emitting-layer hosts. These questions prompted our comparative study of the effects of unipolar currents in Alq and 2-t-butyl-9,10-di(2-naphthyl)anthracene (TBADN), which was chosen as a representative material of the DAA class. First, we identified device structures allowing for rigorous and stable unipolar conduction. Interestingly, even in pristine holes-only devices, our voltammetric measurements indicated that Alq contains a substantial density of deep hole traps (far deeper than what can be explained by energetic disorder), which can be charged by passing holes-only current and seemingly discharged by exposure to white light. As for aged holes-only Alq devices, they exhibited symptoms qualitatively matching those of aged bipolar Alq devices, viz., photoluminescence (PL) loss, transition voltage (V0) rise, and drive voltage (Vd) rise. Notably, PL and V0 are linearly correlated in both holes-only and bipolar devices, which reinforces the supposed link between Alq•+ and the degradation in both types of devices. Yet, there are indications the Alq•+ instability may not be the only degradation pathway in bipolar devices. Even though our observations for holes-only Alq devices agree qualitatively with previously reported ones, we observe far slower degradation rates [Alq PL fades up to ˜500 times slower in holes-only devices, while Alq electroluminescence (EL) fades ˜50 times slower in bipolar control devices]. It is possible that impurities play a significant, perhaps crucial role in the degradation mechanism of both bipolar and holes-only devices, especially the relatively shorter-lived ones. In sharp contrast to Alq, all three observables (PL, V0, and Vd) indicate that holes-only current in TBADN (neat or doped with a perylene-based blue dopant) does not result in degradation in the time that is sufficient for the corresponding bipolar control devices to lose 60%-80% of EL and 20%-30% of PL. We find that the electrons-only current in Alq or TBADN does not result in degradation either. Thus, the degradation of Alq and DAA bipolar devices may be caused by fundamentally dissimilar mechanisms: while hole current may damage the former, it does not appear to affect the latter, suggesting that the initiation step is different.

White OLED in Hybrid Structure for Enhancing Color Purity.

PubMed

Kim, Dong-Eun; Kang, Min-Jae; Park, Gwang-Ryeol; Lee, Burm-Jong; Kwon, Young-Soo; Shin, Hoon-Kyu

2016-06-01

We synthesized the red emission material, bis(1,4-bis(5-phenyloxazol-2-yl)phenyl) iridium(picolate) [Ir-complexes] and the blue emission material, bis (2-(2-hydroxyphenyl) benzoxazolate)zinc [Zn(HPB)2]. White Organic Light Emitting Diodes were fabricated by using Zn(HPB)2 for a blue emitting layer, Ir-complexes for a red emitting layer and a tris (8-hydroxy quinoline)aluminum [Alq3] for a green emitting layer. The important experimental results obtained, white OLED was fabricated by using double emitting layers of Zn(HPB)2 and Alq3:Ir-complexes, and hole blocking layer of 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline[BCP]. We also varied the thickness of BCP. When the thickness of BCP layer was 5 nm, white emission was achieved. We obtained a maximum luminance of 5400 cd/m2 at a current density of 650 mA/cm2. The CIE coordinates was (0.339, 0.323) at voltage of 10 V.

"CH"/N substituted mer-Gaq3 and mer-Alq3 derivatives: an effective approach for the tuning of emitting color.

PubMed

Gahungu, Godefroid; Zhang, Jingping

2005-09-22

Equilibrium geometry configurations of the "CH"/N substituted Alq3 and Gaq3 derivatives are calculated by density functional theory (B3LYP/6-31G). The frontier molecular orbital and gap energy calculations for all complexes have been performed at the HF/6-31G level. It was shown that, compared to the pristine molecules, the HOMO and LUMO are stabilized, the net effect being however an increasing/decreasing of the gap (Eg) depending on the position of the substituted group. On the basis of the equilibrium geometries, the effect of the substitution on the absorption and emission spectra was evaluated using TDB3LYP/3-21G. It was shown that the change of "CH"/N substituted position on 8-hydroxyquinoline ligand is a powerful approach for the tuning of emitting color. An important blue shift was predicted for 5-substituted 8-hydroxyquinoline derivatives, an important red one being observed for 4-substituted ones. Interestingly, relatively significant blue and red shifts were also predicted for the 7- and 2-substituted derivatives. In this work, the correlation between the spectrum shifts and the metal-ligand bonding is also discussed.

Tuning the Performance of Organic Spintronic Devices Using X-Ray Generated Traps

DTIC Science & Technology

2012-08-16

observed in organic devices using the same organic semiconductor, namely tris(8-hydroxyquinoli- nato)aluminium ( Alq3 ) [5,15]. Here we will show that the...manufacturing steps were carried out in a deposition chamber located inside a nitrogen glovebox. Next, the organic layer Alq3 (70 to 100 nm) followed by the...As the organic semiconductor spacer layer, the Alq3 layer was fabricated by thermal evaporation in a vacuum of 10Ś mbar at a rate of 0:1 nm=s. The Fe

Influence of dehydrated nanotubed titanic acid on charge transport and luminescent properties of polymer light-emitting diodes with fluorescent dye

NASA Astrophysics Data System (ADS)

Qian, Lei; Bera, Debasis; Jin, Zhen-Sheng; Du, Zu-Liang; Xu, Zheng; Teng, Feng; Liu, Wei

2007-09-01

In this paper, we discuss the influence of dehydrated nanotubed titanic acid (DNTA) on charge transport and luminescent properties of polymer light-emitting diodes (PLEDs) doped with fluorescent dye. Photoluminescence results confirm the efficient energy transfer from PVK to 4-(dicyanom-ethylene)-2- t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) and tris-(8-hydroxtquinoline) aluminum (Alq 3) in a DNTA-doped device. The device showed lower turn-on voltages and higher charge current by doping with DNTA, which also caused a shift in the exciton's recombination region.

Multi-scale modeling of spin transport in organic semiconductors

NASA Astrophysics Data System (ADS)

Hemmatiyan, Shayan; Souza, Amaury; Kordt, Pascal; McNellis, Erik; Andrienko, Denis; Sinova, Jairo

In this work, we present our theoretical framework to simulate simultaneously spin and charge transport in amorphous organic semiconductors. By combining several techniques e.g. molecular dynamics, density functional theory and kinetic Monte Carlo, we are be able to study spin transport in the presence of anisotropy, thermal effects, magnetic and electric field effects in a realistic morphologies of amorphous organic systems. We apply our multi-scale approach to investigate the spin transport in amorphous Alq3 (Tris(8-hydroxyquinolinato)aluminum) and address the underlying spin relaxation mechanism in this system as a function of temperature, bias voltage, magnetic field and sample thickness.

Study of fluorescence quenching due to 2, 3, 5, 6-tetrafluoro-7, 7', 8, 8'-tetracyano quinodimethane and its solid state diffusion analysis using photoluminescence spectroscopy.

PubMed

Tyagi, Priyanka; Tuli, Suneet; Srivastava, Ritu

2015-02-07

In this work, we have studied the fluorescence quenching and solid state diffusion of 2, 3, 5, 6-tetrafluoro-7,  7',  8,  8'-tetracyano quinodimethane (F4-TCNQ) using photoluminescence (PL) spectroscopy. Quenching studies were performed with tris (8-hydroxyquinolinato) aluminum (Alq3) in solid state samples. Thickness of F4-TCNQ was varied in order to realize different concentrations and study the effect of concentration. PL intensity has reduced with the increase in F4-TCNQ thicknesses. Stern-Volmer and bimolecular quenching constants were evaluated to be 13.8 M(-1) and 8.7 × 10(8) M(-1) s(-1), respectively. The quenching mechanism was found to be of static type, which was inferred by the independent nature of excited state life time from the F4-TCNQ thickness. Further, solid state diffusion of F4-TCNQ was studied by placing a spacing layer of α-NPD between F4-TCNQ and Alq3, and its thickness was varied to probe the diffusion length. PL intensity was found to increase with the increase in this thickness. Quenching efficiency was evaluated as a function of distance between F4-TCNQ and Alq3. These studies were performed for the samples having 1, 2.5, and 5.5 nm thicknesses of F4-TCNQ to study the thickness dependence of diffusion length. Diffusion lengths were evaluated to be 12.5, 15, and 20 nm for 1, 2.5, and 5.5 nm thicknesses of F4-TCNQ. These diffusion lengths were found to be very close to that of determined by secondary ion mass spectroscopy technique.

Carbazole/triarylamine based polymers as a hole injection/transport layer in organic light emitting devices.

PubMed

Wang, Hui; Ryu, Jeong-Tak; Kwon, Younghwan

2012-05-01

This study examined the influence of the charge injection barriers on the performance of organic light emitting diodes (OLEDs) using polymers with a stepwise tuned ionization potential (I(p) approximately -5.01 - -5.29 eV) between the indium tin oxide (ITO) (phi approximately -4.8 eV) anode and tris(8-hydroxyquinolinato) aluminium (Alq3) (I(p) approximately -5.7 eV) layer. The energy levels of the polymers were tuned by structural modification. Double layer devices were fabricated with a configuration of ITO/polymer/Alq3/LiF/Al, where the polymers, Alq3, and LiF/Al were used as the hole injection/transport layer, emissive electron transport layer, and electron injection/cathode, respectively. Using the current density-voltage (J-V), luminescence-voltage (L-V) and efficiencies in these double layer devices, the device performance was evaluated in terms of the energy level alignments at the interfaces, such as the hole injection barriers (phi(h)(iTO/polymer) and phi(h)(polymer/Alq3)) from ITO through the polymers into the Alq3 layer, and the electron injection barrier (phi(e)(polymer/Alq3) or electron/exciton blocking barrier) at the polymer/Alq3 interface.

Large-scale synthesis of a novel tri(8-hydroxyquioline) aluminum nanostructure.

PubMed

Tian, Xike; Fei, Jinbo; Pi, Zhenbang; Yang, Chao; Xiao, Zhidong; Zhang, Lide

2006-08-01

A novel tri(8-hydroxyquioline) aluminum (AlQ3) nanostructure was prepared on large scale at low cost by low-temperature physical vapor deposition (PVD). The morphologies, the chemical bondings, and photoluminescence of the AlQ3 nanostructure were investigated by environmental scanning electronic microscopy (ESEM), Fourier transform infrared spectrum (FT-IR), and photoluminescence (PL) spectra, respectively. The AlQ3 nanostructure was composed of micro-sphere with nanowire-cluster growing on the surface. The diameter of micro-sphere and nanowire were about 5 microm and 80 nm, respectively. FT-IR results indicated that the AlQ3 molecule had a strong thermal stability under research conditions. The growth mechanism of the novel nanostructure was discussed. The novel organic nanostructure would be believed to attractive building field-emission devices and other optical devices.

Bio-recognitive photonics of a DNA-guided organic semiconductor

PubMed Central

Back, Seung Hyuk; Park, Jin Hyuk; Cui, Chunzhi; Ahn, Dong June

2016-01-01

Incorporation of duplex DNA with higher molecular weights has attracted attention for a new opportunity towards a better organic light-emitting diode (OLED) capability. However, biological recognition by OLED materials is yet to be addressed. In this study, specific oligomeric DNA–DNA recognition is successfully achieved by tri (8-hydroxyquinoline) aluminium (Alq3), an organic semiconductor. Alq3 rods crystallized with guidance from single-strand DNA molecules show, strikingly, a unique distribution of the DNA molecules with a shape of an ‘inverted' hourglass. The crystal's luminescent intensity is enhanced by 1.6-fold upon recognition of the perfect-matched target DNA sequence, but not in the case of a single-base mismatched one. The DNA–DNA recognition forming double-helix structure is identified to occur only in the rod's outer periphery. This study opens up new opportunities of Alq3, one of the most widely used OLED materials, enabling biological recognition. PMID:26725969

Bio-recognitive photonics of a DNA-guided organic semiconductor.

PubMed

Back, Seung Hyuk; Park, Jin Hyuk; Cui, Chunzhi; Ahn, Dong June

2016-01-04

Incorporation of duplex DNA with higher molecular weights has attracted attention for a new opportunity towards a better organic light-emitting diode (OLED) capability. However, biological recognition by OLED materials is yet to be addressed. In this study, specific oligomeric DNA-DNA recognition is successfully achieved by tri (8-hydroxyquinoline) aluminium (Alq3), an organic semiconductor. Alq3 rods crystallized with guidance from single-strand DNA molecules show, strikingly, a unique distribution of the DNA molecules with a shape of an 'inverted' hourglass. The crystal's luminescent intensity is enhanced by 1.6-fold upon recognition of the perfect-matched target DNA sequence, but not in the case of a single-base mismatched one. The DNA-DNA recognition forming double-helix structure is identified to occur only in the rod's outer periphery. This study opens up new opportunities of Alq3, one of the most widely used OLED materials, enabling biological recognition.

Bio-recognitive photonics of a DNA-guided organic semiconductor

NASA Astrophysics Data System (ADS)

Back, Seung Hyuk; Park, Jin Hyuk; Cui, Chunzhi; Ahn, Dong June

2016-01-01

Incorporation of duplex DNA with higher molecular weights has attracted attention for a new opportunity towards a better organic light-emitting diode (OLED) capability. However, biological recognition by OLED materials is yet to be addressed. In this study, specific oligomeric DNA-DNA recognition is successfully achieved by tri (8-hydroxyquinoline) aluminium (Alq3), an organic semiconductor. Alq3 rods crystallized with guidance from single-strand DNA molecules show, strikingly, a unique distribution of the DNA molecules with a shape of an `inverted' hourglass. The crystal's luminescent intensity is enhanced by 1.6-fold upon recognition of the perfect-matched target DNA sequence, but not in the case of a single-base mismatched one. The DNA-DNA recognition forming double-helix structure is identified to occur only in the rod's outer periphery. This study opens up new opportunities of Alq3, one of the most widely used OLED materials, enabling biological recognition.

The use of charge extraction by linearly increasing voltage in polar organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Züfle, Simon; Altazin, Stéphane; Hofmann, Alexander; Jäger, Lars; Neukom, Martin T.; Schmidt, Tobias D.; Brütting, Wolfgang; Ruhstaller, Beat

2017-05-01

We demonstrate the application of the CELIV (charge carrier extraction by linearly increasing voltage) technique to bilayer organic light-emitting devices (OLEDs) in order to selectively determine the hole mobility in N,N0-bis(1-naphthyl)-N,N0-diphenyl-1,10-biphenyl-4,40-diamine (α-NPD). In the CELIV technique, mobile charges in the active layer are extracted by applying a negative voltage ramp, leading to a peak superimposed to the measured displacement current whose temporal position is related to the charge carrier mobility. In fully operating devices, however, bipolar carrier transport and recombination complicate the analysis of CELIV transients as well as the assignment of the extracted mobility value to one charge carrier species. This has motivated a new approach of fabricating dedicated metal-insulator-semiconductor (MIS) devices, where the extraction current contains signatures of only one charge carrier type. In this work, we show that the MIS-CELIV concept can be employed in bilayer polar OLEDs as well, which are easy to fabricate using most common electron transport layers (ETLs), like Tris-(8-hydroxyquinoline)aluminum (Alq3). Due to the macroscopic polarization of the ETL, holes are already injected into the hole transport layer below the built-in voltage and accumulate at the internal interface with the ETL. This way, by a standard CELIV experiment only holes will be extracted, allowing us to determine their mobility. The approach can be established as a powerful way of selectively measuring charge mobilities in new materials in a standard device configuration.

A Planar, Chip-Based, Dual-Beam Refractometer Using an Integrated Organic Light Emitting Diode (OLED) Light Source and Organic Photovoltaic (OPV) Detectors

PubMed Central

Ratcliff, Erin L.; Veneman, P. Alex; Simmonds, Adam; Zacher, Brian; Huebner, Daniel

2010-01-01

We present a simple chip-based refractometer with a central organic light emitting diode (OLED) light source and two opposed organic photovoltaic (OPV) detectors on an internal reflection element (IRE) substrate, creating a true dual-beam sensor platform. For first-generation platforms, we demonstrate the use of a single heterojunction OLED based on electroluminescence emission from an Alq3/TPD heterojunction (tris-(8-hydroxyquinoline)aluminum/N,N′-Bis(3-methylphenyl)-N,N′-diphenylbenzidine) and light detection with planar heterojunction pentacene/C60 OPVs. The sensor utilizes the considerable fraction of emitted light from conventional thin film OLEDs that is coupled into guided modes in the IRE instead of into the forward (display) direction. A ray-optics description is used to describe light throughput and efficiency-limiting factors for light coupling from the OLED into the substrate modes, light traversing through the IRE substrate, and light coupling into the OPV detectors. The arrangement of the OLED at the center of the chip provides for two sensing regions, a “sample” and “reference” channel, with detection of light by independent OPV detectors. This configuration allows for normalization of the sensor response against fluctuations in OLED light output, stability, and local fluctuations (temperature) which might influence sensor response. The dual beam configuration permits significantly enhanced sensitivity to refractive index changes relative to single-beam protocols, and is easily integrated into a field-portable instrumentation package. Changes in refractive index (ΔR.I.) between 10−2 and 10−3 R.I. units could be detected for single channel operation, with sensitivity increased to ΔR.I. ≈ 10−4 units when the dual beam configuration is employed. PMID:20218580

Spectral broadening in electroluminescence of white organic light-emitting diodes based on complementary colors

NASA Astrophysics Data System (ADS)

Kim, Young Min; Park, Young Wook; Choi, Jin Hwan; Ju, Byeong Kwon; Jung, Jae Hoon; Kim, Jai Kyeong

2007-01-01

The authors report the optical and electroluminescent (EL) properties of white organic light-emitting diodes (OLEDs) which have two emitters with similar structures: 1, 1, 4, 4-tetraphenyl-1, 3-butadiene and 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline have an emission peak of 400nm around the near ultraviolet, and tris-(8-hydroxyquinoline) aluminum doped with 4-(dicyanomethylene)-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran has an emission peak of 580nm producing a yellow color. The EL spectra of the white OLED have shown a broadening through visual range from 400to780nm. This spectral broadening is related to an exciplex emission at the organic solid interface.

Anthracene-Based Organic Small-Molecule Electron-Injecting Material for Inverted Organic Light-Emitting Diodes.

PubMed

Matsuo, Yutaka; Okada, Hiroshi; Kondo, Yasuhiro; Jeon, Il; Wang, Huan; Yu, Yun; Matsushita, Takeshi; Yanai, Motoki; Ikuta, Toshiaki

2018-04-11

A diphenylanthracene dimethylamine derivative (9-{3,5-di( N, N-dimethylaminoethoxy)phenyl}-10-phenyl-anthracene, DPAMA) was synthesized by the Suzuki-Miyaura cross-coupling reaction. Its ammonium salt, 9-{3,5-di(trimethylammonium ethoxy)phenyl}-10-phenyl-anthracene dichloride (DPAMA-Cl), was also synthesized as a reference material. DPAMA was characterized by UV-vis and fluorescence spectroscopy, cyclic voltammetry, photoelectron yield spectroscopy, and X-ray photoelectron spectroscopy to evaluate the work function-modifying ability of DPAMA on indium tin oxide (ITO) and ZnO. The work functions of ITO and ZnO changed from 4.4 and 4.0 eV (pristine) to 3.8 and 3.9 eV, respectively. Using this surface modification effect of DPAMA, inverted organic light-emitting diodes were fabricated with device structures of ITO/DPAMA/Alq 3 /NPD/MoO 3 /Al (Alq 3 = tris(8-hydroxyquinolinato)aluminum; NPD = N, N'-di-[(1-naphthyl)- N, N'-diphenyl]-1,1'-(biphenyl)-4,4'-diamine) and ITO/ZnO/DPAMA/Alq 3 /NPD/MoO 3 /Al. Both devices showed good performance at the range of current density, 1-300 mA/cm 2 . The best inverted organic light-emitting diodes device showed luminance of 7720 cd/m 2 , current efficiency of 4.51 cd/A, and external quantum efficiency of 1.45%. Also, poly(3-hexylthiophene):mixed phenyl-C 61 and C 71 butyric acid methyl ester-based organic solar cells using DPAMA and DPAMA-Cl as electron-transporting materials showed power conversion efficiencies of 3.3 and 3.4%, respectively.

Characterisation of different polymorphs of tris(8-hydroxyquinolinato)aluminium(III) using solid-state NMR and DFT calculations

PubMed Central

Goswami, Mithun; Nayak, Pabitra K; Periasamy, N; Madhu, PK

2009-01-01

Background Organic light emitting devices (OLED) are becoming important and characterisation of them, in terms of structure, charge distribution, and intermolecular interactions, is important. Tris(8-hydroxyquinolinato)-aluminium(III), known as Alq3, an organomettalic complex has become a reference material of great importance in OLED. It is important to elucidate the structural details of Alq3 in its various isomeric and solvated forms. Solid-state nuclear magnetic resonance (NMR) is a useful tool for this which can also complement the information obtained with X-ray diffraction studies. Results We report here 27Al one-dimensional (1D) and two-dimensional (2D) multiple-quantum magic-angle spinning (MQMAS) NMR studies of the meridional (α-phase) and the facial (δ-phase) isomeric forms of Alq3. Quadrupolar parameters are estimated from the 1D spectra under MAS and anisotropic slices of the 2D spectra and also calculated using DFT (density functional theory) quantum-chemical calculations. We have also studied solvated phase of Alq3 containing ethanol in its lattice. We show that both the XRD patterns and the quadrupolar parameters of the solvated phase are different from both the α-phase and the δ-phase, although the fluorescence emission shows no substantial difference between the α-phase and the solvated phase. Moreover, we have shown that after the removal of ethanol from the matrix the solvated Alq3 has similar XRD patterns and quadrupolar parameters to that of the α-phase. Conclusion The 2D MQMAS experiments have shown that all the different modifications of Alq3 have 27Al in single unique crystallographic site. The quadrupolar parameters predicted using the DFT calculation under the isodensity polarisable continuum model resemble closely the experimentally obtained values. The solvated phase of Alq3 containing ethanol has structural difference from the α-phase of Alq3 (containing meridional isomer) from the solid-state NMR studies. Solid-state NMR can hence be used as an effective complementary tool to XRD for characterisation and structural elucidation. PMID:19900275

Characterisation of different polymorphs of tris(8-hydroxyquinolinato)aluminium(III) using solid-state NMR and DFT calculations.

PubMed

Goswami, Mithun; Nayak, Pabitra K; Periasamy, N; Madhu, P K

2009-11-09

Organic light emitting devices (OLED) are becoming important and characterisation of them, in terms of structure, charge distribution, and intermolecular interactions, is important. Tris(8-hydroxyquinolinato)-aluminium(III), known as Alq3, an organomettalic complex has become a reference material of great importance in OLED. It is important to elucidate the structural details of Alq3 in its various isomeric and solvated forms. Solid-state nuclear magnetic resonance (NMR) is a useful tool for this which can also complement the information obtained with X-ray diffraction studies. We report here 27Al one-dimensional (1D) and two-dimensional (2D) multiple-quantum magic-angle spinning (MQMAS) NMR studies of the meridional (alpha-phase) and the facial (delta-phase) isomeric forms of Alq3. Quadrupolar parameters are estimated from the 1D spectra under MAS and anisotropic slices of the 2D spectra and also calculated using DFT (density functional theory) quantum-chemical calculations. We have also studied solvated phase of Alq3 containing ethanol in its lattice. We show that both the XRD patterns and the quadrupolar parameters of the solvated phase are different from both the alpha-phase and the delta-phase, although the fluorescence emission shows no substantial difference between the alpha-phase and the solvated phase. Moreover, we have shown that after the removal of ethanol from the matrix the solvated Alq3 has similar XRD patterns and quadrupolar parameters to that of the alpha-phase. The 2D MQMAS experiments have shown that all the different modifications of Alq3 have 27Al in single unique crystallographic site. The quadrupolar parameters predicted using the DFT calculation under the isodensity polarisable continuum model resemble closely the experimentally obtained values. The solvated phase of Alq3 containing ethanol has structural difference from the alpha-phase of Alq3 (containing meridional isomer) from the solid-state NMR studies. Solid-state NMR can hence be used as an effective complementary tool to XRD for characterisation and structural elucidation.

Understanding M-ligand bonding and mer-/fac-isomerism in tris(8-hydroxyquinolinate) metallic complexes.

PubMed

Lima, Carlos F R A C; Taveira, Ricardo J S; Costa, José C S; Fernandes, Ana M; Melo, André; Silva, Artur M S; Santos, Luís M N B F

2016-06-28

Tris(8-hydroxyquinolinate) metallic complexes, Mq3, are one of the most important classes of organic semiconductor materials. Herein, the nature of the chemical bond in Mq3 complexes and its implications on their molecular properties were investigated by a combined experimental and computational approach. Various Mq3 complexes, resulting from the alteration of the metal and substitution of the 8-hydroxyquinoline ligand in different positions, were prepared. The mer-/fac-isomerism in Mq3 was explored by FTIR and NMR spectroscopy, evidencing that, irrespective of the substituent, mer- and fac-are the most stable molecular configurations of Al(iii) and In(iii) complexes, respectively. The relative M-ligand bond dissociation energies were evaluated experimentally by electrospray ionization tandem mass spectrometry (ESI-MS-MS), showing a non-monotonous variation along the group (Al > In > Ga). The results reveal a strong covalent character in M-ligand bonding, which allows for through-ligand electron delocalization, and explain the preferred molecular structures of Mq3 complexes as resulting from the interplay between bonding and steric factors. The mer-isomer reduces intraligand repulsions, being preferred for smaller metals, while the fac-isomer is favoured for larger metals where stronger covalent M-ligand bonds can be formed due to more extensive through-ligand conjugation mediated by metal "d" orbitals.

Sharp green electroluminescence from 1H-pyrazolo[3,4-b]quinoline-based light-emitting diodes

NASA Astrophysics Data System (ADS)

Tao, Y. T.; Balasubramaniam, E.; Danel, A.; Jarosz, B.; Tomasik, P.

2000-09-01

A multilayer organic light-emitting diode was fabricated using a fluorescent compound {6-N,N-diethylamino-1-methyl-3-phenyl-1H-pyrazolo[3,4-b]quinoline} (PAQ-NEt2) doped into the hole-transporting layer of NPB {4,4'-bis[N-(1-naphthyl-1-)-N-phenyl-amino]-biphenyl}, with the TPBI {2,2',2″-(1,3,5-phenylene)tris[1-phenyl-1H-benzimidazole]} as an electrontransporting material. At 16% PAQ-NEt2 doping concentration, the device gave a sharp, bright, and efficient green electroluminescence (EL) peaked at around 530 nm. The full width at half maximum of the EL is 60 nm, which is 60% of the green emission from typical NPB/AlQ [where AlQ=tris(8-hydroxyquinoline) aluminum] device. For the same concentration, a maximum luminance of 37 000 cd/m2 was obtained at 10.0 V and the maximum power, luminescence, and external quantum efficiencies were obtained 4.2 lm/W, 6.0 cd/A, and 1.6%, respectively, at 5.0 V.

Enhanced Emission Efficiency in Organic Light-Emitting Diodes Using Deoxyribonucleic Acid Complex as an Electron Blocking Layer

DTIC Science & Technology

2006-04-28

1. Color online Photographs of EL emission from several devices: a green Alq3 baseline OLED at 25 V 707 mA/cm2—590 cd/m2, 0.35 cd/A; b green... Alq3 BioLED with DNA EBL at 25 V 308 mA/cm2—21 100 cd/m2, 6.56 cd/A; c blue NPB baseline OLED at 20 V 460 mA/cm2—700 cd/m2, 0.14 cd/A; d blue...al. Appl. Phys. Lett. 88, 171109 2006NPB N ,N-bisnaphthalene-1-yl-N ,N-bisphenyl benzi- dine hole transport layer HTL; Alq3 tris-8

White-light-emitting organic electroluminescent devices based on interlayer sequential energy transfer

NASA Astrophysics Data System (ADS)

Deshpande, R. S.; Bulović, V.; Forrest, S. R.

1999-08-01

We demonstrate efficient, molecular organic white-light-emitting devices using vacuum-deposited thin films of red luminescent [2-methyl-6-[2-(2,3,6,7-tetrahydro-1H, 5H-benzo [ij] quinolizin-9-yl) ethenyl]-4H-pyran-4-ylidene] propane-dinitrile (DCM2), doped into blue-emitting 4, 4' bis [N-1-napthyl-N-phenyl-amino]biphenyl (α-NPD), and green-emitting tris-(8-hydroxyquinolinato) aluminum(III) (AlQ3). The luminescent layers are separated by a hole-blocking layer of 2,9-dimethyl, 4,7-diphenyl, 1,10-phenanthroline (BCP), whose thickness is on the order of a typical Förster transfer radius of 30-40 Å. Excitons formed on α-NPD sequentially transfer their energy via a Förster mechanism to AlQ3 across the BCP layer, and from AlQ3 to DCM2. This interlayer sequential energy transfer results in partial excitation of all three molecular species, thereby producing white light emission. The thickness of the blocking layer and the concentration of DCM2 in α-NPD permit the tuning of the device spectrum to achieve a balanced white emission with Commission Internationale d'Eclairage chromaticity coordinates of (0.33, 0.33). The spectrum is largely insensitive to the drive current, and the devices have a maximum luminance of 13 500 cd/m2. At a luminance of 100 cd/m2, the quantum and power efficiencies are 0.5% and 0.35 lm/W, respectively.

Growth and Brilliant Photo-Emission of Crystalline Hexagonal Column of Alq3 Microwires

PubMed Central

Kim, Seokho; Kim, Do Hyoung; Choi, Jinho; Lee, Hojin; Kim, Sun-Young; Park, Jung Woon; Park, Dong Hyuk

2018-01-01

We report the growth and nanoscale luminescence characteristics of 8-hydroxyquinolinato aluminum (Alq3) with a crystalline hexagonal column morphology. Pristine Alq3 nanoparticles (NPs) were prepared using a conventional reprecipitation method. Crystal hexagonal columns of Alq3 were grown by using a surfactant-assisted self-assembly technique as an adjunct to the aforementioned reprecipitation method. The formation and structural properties of the crystalline and non-crystalline Alq3 NPs were analyzed with scanning electron microscopy and X-ray diffraction. The nanoscale photoluminescence (PL) characteristics and the luminescence color of the Alq3 single NPs and their crystal microwires (MWs) were evaluated from color charge-coupled device images acquired using a high-resolution laser confocal microscope. In comparison with the Alq3 NPs, the crystalline MWs exhibited a very bright and sharp emission. This enhanced and sharp emission from the crystalline Alq3 single MWs originated from effective π-π stacking of the Alq3 molecules due to strong interactions in the crystalline structure. PMID:29565306

Aluminum surface corrosion and the mechanism of inhibitors using pH and metal ion selective imaging fiber bundles.

PubMed

Szunerits, Sabine; Walt, David R

2002-02-15

The localized corrosion behavior of a galvanic aluminum copper couple was investigated by in situ fluorescence imaging with a fiber-optic imaging sensor. Three different, but complementary methods were used for visualizing remote corrosion sites, mapping the topography of the metal surface, and measuring local chemical concentrations of H+, OH-, and Al3+. The first method is based on a pH-sensitive imaging fiber, where the fluorescent dye SNAFL was covalently attached to the fiber's distal end. Fluorescence images were acquired as a function of time at different areas of the galvanic couple. In a second method, the fluorescent dye morin was immobilized on the fiber-optic imaging sensor, which allowed the in situ localization of corrosion processes on pure aluminum to be visualized over time by monitoring the release of Al3+. The development of fluorescence on the aluminum surface defined the areas associated with the anodic dissolution of aluminum. We also investigated the inhibition of corrosion of pure aluminum by CeCl3 and 8-hydroxyquinoline. The decrease in current, the decrease in the number of active sites on the aluminum surface, and the faster surface passivation are all consistent indications that cerium chloride and 8-hydroxyquinoline inhibit corrosion effectively. From the number and extent of corrosion sites and the release of aluminum ions monitored with the fiber, it was shown that 8-hydroxyquinoline is a more effective inhibitor than cerium chloride.

Tandem organic light-emitting diodes with KBH4 doped 9,10-bis(3-(pyridin-3-yl)phenyl) anthracene connected to the charge generation layer.

PubMed

Duan, Lian; Tsuboi, Taiju; Qiu, Yong; Li, Yanrui; Zhang, Guohui

2012-06-18

Tandem organic light emitting diodes (OLEDs) are ideal for lighting applications due to their low working current density at high brightness. In this work, we have studied an efficient electron transporting layer of KBH(4) doped 9,10-bis(3-(pyridin-3-yl)phenyl)anthracene (DPyPA) which is located adjacent to charge generation layer of MoO(3)/NPB. The excellent transporting property of the DPyPA:KBH(4) layer helps the tandem OLED to achieve a lower voltage than the tandem device with the widely used tris-(8-hydroxyquinoline)aluminum:Li. For the tandem white OLED with a fluorescent blue unit and a phosphorescent yellow unit, we've achieved a high current efficiency of 75 cd/A, which can be further improved to 120 cd/A by attaching a diffuser layer.

Ultrahigh density array of vertically aligned small-molecular organic nanowires on arbitrary substrates.

PubMed

Starko-Bowes, Ryan; Pramanik, Sandipan

2013-06-18

In recent years π-conjugated organic semiconductors have emerged as the active material in a number of diverse applications including large-area, low-cost displays, photovoltaics, printable and flexible electronics and organic spin valves. Organics allow (a) low-cost, low-temperature processing and (b) molecular-level design of electronic, optical and spin transport characteristics. Such features are not readily available for mainstream inorganic semiconductors, which have enabled organics to carve a niche in the silicon-dominated electronics market. The first generation of organic-based devices has focused on thin film geometries, grown by physical vapor deposition or solution processing. However, it has been realized that organic nanostructures can be used to enhance performance of above-mentioned applications and significant effort has been invested in exploring methods for organic nanostructure fabrication. A particularly interesting class of organic nanostructures is the one in which vertically oriented organic nanowires, nanorods or nanotubes are organized in a well-regimented, high-density array. Such structures are highly versatile and are ideal morphological architectures for various applications such as chemical sensors, split-dipole nanoantennas, photovoltaic devices with radially heterostructured "core-shell" nanowires, and memory devices with a cross-point geometry. Such architecture is generally realized by a template-directed approach. In the past this method has been used to grow metal and inorganic semiconductor nanowire arrays. More recently π-conjugated polymer nanowires have been grown within nanoporous templates. However, these approaches have had limited success in growing nanowires of technologically important π-conjugated small molecular weight organics, such as tris-8-hydroxyquinoline aluminum (Alq3), rubrene and methanofullerenes, which are commonly used in diverse areas including organic displays, photovoltaics, thin film transistors and spintronics. Recently we have been able to address the above-mentioned issue by employing a novel "centrifugation-assisted" approach. This method therefore broadens the spectrum of organic materials that can be patterned in a vertically ordered nanowire array. Due to the technological importance of Alq3, rubrene and methanofullerenes, our method can be used to explore how the nanostructuring of these materials affects the performance of aforementioned organic devices. The purpose of this article is to describe the technical details of the above-mentioned protocol, demonstrate how this process can be extended to grow small-molecular organic nanowires on arbitrary substrates and finally, to discuss the critical steps, limitations, possible modifications, trouble-shooting and future applications.

IZO deposited by PLD on flexible substrate for organic heterostructures

NASA Astrophysics Data System (ADS)

Socol, M.; Preda, N.; Stanculescu, A.; Breazu, C.; Florica, C.; Rasoga, O.; Stanculescu, F.; Socol, G.

2017-05-01

In:ZnO (IZO) thin films were deposited on flexible plastic substrates by pulsed laser deposition (PLD) method. The obtained layers present adequate optical and electrical properties competitive with those based on indium tin oxide (ITO). The figure of merit (9 × 10-3 Ω-1) calculated for IZO layers demonstrates that high quality coatings can be prepared by this deposition technique. A thermal annealing (150 °C for 1 h) or an oxygen plasma etching (6 mbar for 10 min.) were applied to the IZO layers to evaluate the influence of these treatments on the properties of the transparent coatings. Using vacuum evaporation, organic heterostructures based on cooper phthalocyanine (CuPc) and 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA) were deposited on the untreated and treated IZO layers. The optical and electrical properties of the heterostructures were investigated by UV-Vis, FTIR and current-voltage ( I- V) measurements. For the heterostructure fabricated on IZO treated in oxygen plasma, an improvement in the current value with at least one order of magnitude was evidenced in the I- V characteristics recorded in dark conditions. Also, an increase in the current value for the heterostructure deposited on untreated IZO layer can be achieved by adding an organic layer such as tris-8-hydroxyquinoline aluminium (Alq3).

Microstructural studies of organic spin valves and superconducting vortex ratchets

NASA Astrophysics Data System (ADS)

Liu, Yaohua

Thin film's microstructure plays important roles in their transport properties. Spin transport in organic semiconductors (OSCs) were studied using spin valves structures, with Fe and Co as the top and bottom ferromagnetic (FM) contacts, respectively. Magnetoresistance (MR) effects have been observed up to room temperature in junctions based on an electron-carrying OSC, tris(8-hyroxyquinoline) aluminum (Alq3) and a hole-carrying OSC, copper phthalocyanine (CuPc). However, junctions based on two other electron-carrying OSCs with higher lateral mobilities showed weaker spin transport effects. Morphological studies indicated that these high mobility films had rougher surfaces than either Alq3 or CuPc, therefore the degradation may originate from enhanced scattering due to the rougher FM/OSC interfaces. FM/OSC interfaces were studied in detail in Alga-based devices. These multilayer films have well-defined layer structures with modest average chemical roughness (3-5 nm) at the FM/A1q3 interfaces. Reflectometry shows that larger MR effects are correlated with sharper FM/OSC interfaces and a magnetically dead layer at the Alq3/Fe boundary. Combined with magnetotransport and magnetometery studies, our results support spin injection and transport in Alq3. A lower bound for the spin diffusion length in Alq3 was estimated as 43 +/- 5 nm at 80 K. However, the subtle correlations between microstructure and magnetotransport indicate the importance of interfacial effects. Thin film's microstructures can also be engineered to study interesting physics phenomena. We studied superconducting vortex motion, especially the vortex ratchet effect, in one-dimensional thickness-modulated granular Al films. The potential profile for a single vortex due to thickness modulation was estimated using the Bardeen-Stephen model, which agrees with the transport results. For a sample with a nearly sawtooth potential profile, the rectification velocity showed a maximum around 4.4B1, where B1 is the first matching field, similar to simulations. We also observed reverse vortex rectification, which originates from the interplay between the pinning potential and vortex-vortex interactions. More interestingly, the rectification effects showed clear frequency dependence at driving frequencies as low as 10 kHz, suggesting the failure of the heavily overdamped model.

Large Magnetoresistance at High Bias Voltage in Double-layer Organic Spin Valves

NASA Astrophysics Data System (ADS)

Subedi, R. C.; Liang, S. H.; Geng, R.; Zhang, Q. T.; Lou, L.; Wang, J.; Han, X. F.; Nguyen, T. D.

We report studies of magnetoresistance (MR) in double-layer organic spin valves (DOSV) using tris (8-hydroxyquinolinato) aluminum (Alq3) spacers. The device exhibits three distinct resistance levels depending on the relative magnetizations of the ferromagnetic electrodes. We observed a much weaker bias voltage dependence of MR in the device compared to that in the conventional organic spin valve (OSV). The MR magnitude reduces by the factor of two at 0.7 V bias voltage in the DOSV compared to 0.02 V in the conventional OSV. Remarkably, the MR magnitude reaches 0.3% at 6 V bias in the DOSVs, the largest MR response ever reported in OSVs at this bias. Our finding may have a significant impact on achieving high efficient bipolar OSVs strictly performed at high voltages. University of Georgia start-up fund, Ministry of Education, Singapore, National Natural Science Foundation of China.

Hole-exciton interaction induced high field decay of magneto-electroluminescence in Alq3-based organic light-emitting diodes at room temperature

NASA Astrophysics Data System (ADS)

Zhang, Tingting; Holford, D. F.; Gu, Hang; Kreouzis, T.; Zhang, Sijie; Gillin, W. P.

2016-01-01

The magnetic field effects on the electroluminescence of aluminium tris-(8-hydroxyqinoline) (Alq3) based organic light emitting diodes have been investigated by varying the electron/hole ratio in the emissive layer. Experimental results reveal that a negative high field effect in the magneto-electroluminescence (MEL) can be found in devices with very low triplet exciton concentration at room temperature. This suggests triplet-triplet annihilation cannot be used to explain the negative high field MEL in the Alq3 system. Our results suggest that hole-exciton interaction may be the origin of the negative high field MEL and also, in parallel with this interaction, there is also the more common positive high field process occurring which has been tentatively attributed to electron-exciton interactions. The competition between these different processes decides the final shape of the MEL at high fields.

Emission color tuning in AlQ3 complexes with extended conjugated chromophores.

PubMed

Pohl, Radek; Anzenbacher, Pavel

2003-08-07

[reaction: see text] A new method for the synthesis of 5-arylethynyl-8-hydroxyquinoline ligands using Sonogashira-Hagihara coupling was developed. The electronic nature of arylethynyl substituents affects the emission color and quantum yield of the resulting Al(III) complex. Photophysical properties of the metallocomplexes correspond to the electron-withdrawing/-donating character of the arylethynyl substituents. Optical properties of such Al(III) complexes correlate with the Hammett constant values of the respective substituents. This strategy offers a powerful tool for the preparation of electroluminophores with predictable photophysical properties.

Evidence for alkali metal formation at a cathode interface of organic electroluminescent devices by thermal decomposition of alkali metal carboxylates during their vapor deposition

NASA Astrophysics Data System (ADS)

Ganzorig, Chimed; Fujihira, Masamichi

2004-11-01

This study examines the possibility of thermal decomposition of Na salts of acetate, benzoate, and fluoride during vacuum vapor deposition using a quartz crystal microbalance to measure negative frequency shift (Δf) caused by increasing mass deposited from the same amount of source materials. Cs acetate is also examined. We compare the negative frequency shift-source current (Δf -I) curves of the Na salts with those of organic materials such as tris(8-hydroxyquinoline)aluminum and N ,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine. CH3COONa and C6H5COONa exhibit much lower Δf than the organic materials. CH3COOCs gives much larger Δf than CH3COONa due to the higher atomic weight of Cs. These exhibit clear evidence for alkali metal formation by thermal decomposition during vapor deposition of alkali metal carboxylates.

Addressing the efficiency roll-off in a fluorescent OLED by facile electron transport layer doping and carrier confinement

NASA Astrophysics Data System (ADS)

Soman, Anjaly; M, Manuraj; Unni, K. N. Narayanan

2018-05-01

Organic light emitting diodes (OLEDs) often face the issue of decreasing power efficiency with increasing brightness. Loss of charge carrier balance is one of the factors contributing to the efficiency roll-off. We demonstrate that by using a combination of doped electron transport layer (ETL) and a specially chosen electron blocking layer (EBL) having high hole mobility, this efficiency roll-off can be effectively suppressed. A tris-(8-hydroxyquinoline) aluminium (Alq3) based OLED has been fabricated with 2,3,6,7-Tetrahydro-1,1,7,7,-tetramethyl-1H, 5H,11H-10-(2-benzothiazolyl) quinolizino-[9,9a, 1n gh]coumarin (C545T) as the emissive dopant. Bulk doping of the ETL with lithium fluoride (LiF) was optimized to increase the luminous intensity as well as the current efficiency. An EBL with high hole mobility introduced between the EML and the hole transport layer (HTL) improved the performance drastically, and the device brightness at 9 V got improved by a factor of 2.5 compared to that of the control device. While increasing the brightness from 100 cd/m2 to 1000 cd/m2, the power efficiency drop was 47% for the control device whereas only a drop of 15% was observed for the modified device. The possible mechanisms for the enhanced performance are discussed.

Ultrahigh Density Array of Vertically Aligned Small-molecular Organic Nanowires on Arbitrary Substrates

PubMed Central

Starko-Bowes, Ryan; Pramanik, Sandipan

2013-01-01

In recent years π-conjugated organic semiconductors have emerged as the active material in a number of diverse applications including large-area, low-cost displays, photovoltaics, printable and flexible electronics and organic spin valves. Organics allow (a) low-cost, low-temperature processing and (b) molecular-level design of electronic, optical and spin transport characteristics. Such features are not readily available for mainstream inorganic semiconductors, which have enabled organics to carve a niche in the silicon-dominated electronics market. The first generation of organic-based devices has focused on thin film geometries, grown by physical vapor deposition or solution processing. However, it has been realized that organic nanostructures can be used to enhance performance of above-mentioned applications and significant effort has been invested in exploring methods for organic nanostructure fabrication. A particularly interesting class of organic nanostructures is the one in which vertically oriented organic nanowires, nanorods or nanotubes are organized in a well-regimented, high-density array. Such structures are highly versatile and are ideal morphological architectures for various applications such as chemical sensors, split-dipole nanoantennas, photovoltaic devices with radially heterostructured "core-shell" nanowires, and memory devices with a cross-point geometry. Such architecture is generally realized by a template-directed approach. In the past this method has been used to grow metal and inorganic semiconductor nanowire arrays. More recently π-conjugated polymer nanowires have been grown within nanoporous templates. However, these approaches have had limited success in growing nanowires of technologically important π-conjugated small molecular weight organics, such as tris-8-hydroxyquinoline aluminum (Alq3), rubrene and methanofullerenes, which are commonly used in diverse areas including organic displays, photovoltaics, thin film transistors and spintronics. Recently we have been able to address the above-mentioned issue by employing a novel "centrifugation-assisted" approach. This method therefore broadens the spectrum of organic materials that can be patterned in a vertically ordered nanowire array. Due to the technological importance of Alq3, rubrene and methanofullerenes, our method can be used to explore how the nanostructuring of these materials affects the performance of aforementioned organic devices. The purpose of this article is to describe the technical details of the above-mentioned protocol, demonstrate how this process can be extended to grow small-molecular organic nanowires on arbitrary substrates and finally, to discuss the critical steps, limitations, possible modifications, trouble-shooting and future applications. PMID:23852129

The effect of the hole injection layer on the performance of single layer organic light-emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wenjin, Zeng; Ran, Bi; Hongmei, Zhang, E-mail: iamhmzhang@njupt.edu.cn, E-mail: iamwhuang@njupt.edu.cn

2014-12-14

Efficient single-layer organic light-emitting diodes (OLEDs) were reported based on a green fluorescent dye 10-(2-benzothiazolyl)-2,3,6,7-tetrahydro-1,1,7,7–tetramethyl-1H,5H,11H-(1) benzopyropyrano (6,7-8-I,j)quinolizin-11-one (C545T). Herein, poly(3,4-ethylenedioxy thiophene) poly(styrene sulfonate) were, respectively, applied as the injection layer for comparison. The hole transport properties of the emission layer with different hole injection materials are well investigated via current-voltage measurement. It was clearly found that the hole injection layers (HILs) play an important role in the adjustment of the electron/hole injection to attain transport balance of charge carriers in the single emission layer of OLEDs with electron-transporting host. The layer of tris-(8-hydroxyquinoline) aluminum played a dual role of hostmore » and electron-transporting materials within the emission layer. Therefore, appropriate selection of hole injection layer is a key factor to achieve high efficiency OLEDs with single emission layer.« less

Self-assembly of 2-aldehyde-8-hydroxyquinolinate-based lanthanide complexes and NIR luminescence

NASA Astrophysics Data System (ADS)

Zhang, Meiqi; Li, Hongfeng; Chen, Peng; Sun, Wenbin; Zhang, Lei; Yan, Pengfei

2015-02-01

Self-assembly reaction of 2-aldehyde-8-hydroxyquinoline, tris(hydroxymethyl)aminomethane and LnCl3ṡ6H2O affords a series of mononuclear lanthanide complexes Ce(baho)2·Et2O (1) (H2baho = 2,8-bis(2-(8-hydroxylquinolinyl))-1-aza-5-hydroxymethyl-3,7-dioxabicyclo[3.3.0]octane), Dy(nhm)2Cl·0.5H2O (2) and Ln(nhm)2Cl·0.5C6H14 (Ln = Ho (3), Er (4), Yb (5) and Hnhm = N-(2-(8-hydroxylquinolinyl)methylene)(trishydroxymethyl)methylamine. The crystal structures have been determined by X-ray crystallographic analysis, and the tetravalence of Ce in 1 has been proven by XPS. Interestingly, the positive charge of Ce4+ ion in 1 is neutralized by two deprotonated baho2- ligands, while two deprotonated nhm- ligands and one Cl- compensate the positive charge of Ln3+ ions in 2-5. Complex 5 exhibit essential NIR luminescence of Yb3+ ion with lifetime of 17.64 μs in solid and 9.96 μs in CH3OH solution.

JPRS Report, Science & Technology, Japan, Joint Convention of Electrical and Information Engineers

DTIC Science & Technology

1990-10-26

structure in which a thin vacuum vapor deposited film of diamine and aluminum quinoline complex ( Alq3 ) is laminated on a glass substrate on which an ITO...spectrum almost coincides with the luminous spectrum of Alq3 , which is a fluorescent substance and is known to be a luminescence from Alq3 . The...luminous mechanism of this EL device is roughly understood as follows. Alq3 has a high resistance together with being a fluorescent pigment of a high

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Tingting; Holford, D. F.; Gu, Hang

The magnetic field effects on the electroluminescence of aluminium tris-(8-hydroxyqinoline) (Alq{sub 3}) based organic light emitting diodes have been investigated by varying the electron/hole ratio in the emissive layer. Experimental results reveal that a negative high field effect in the magneto-electroluminescence (MEL) can be found in devices with very low triplet exciton concentration at room temperature. This suggests triplet-triplet annihilation cannot be used to explain the negative high field MEL in the Alq{sub 3} system. Our results suggest that hole-exciton interaction may be the origin of the negative high field MEL and also, in parallel with this interaction, there ismore » also the more common positive high field process occurring which has been tentatively attributed to electron-exciton interactions. The competition between these different processes decides the final shape of the MEL at high fields.« less

Kinetics of the substitution of dehydroacetic acid in tris (dehydroacetato) Fe(III) complex by 8-hydroxyquinoline, di- and tetra-hydroxyquinone

NASA Astrophysics Data System (ADS)

Fouad, D. M.; Ismail, N. M.; El-Gahami, M. A.; Ibrahim, S. A.

2007-06-01

The ligand substitution reactions of dehydroacetic acid (Hdha) in [Fe(dha) 3] with second ligand such as 8-hydroxyquinoline (Hquin), 1,4-dihydroxyanthraquinone (H 2dhaq) and 1,4,5,8-tetra-hydroxyanthraquinone (H 4thaq) were investigated spectrophotometrically by in low polarity solvents like benzene, chloroform and dichloromethane. It is deduced that the substitution reaction takes place through one successive step. The reaction was performed at four different temperatures (5-25) °C, and it exhibits a first order dependence on the concentration of the starting complex. The observed rate constant depends on the concentration of both leaving and entering ligands. The evaluation of the kinetic data gives activation parameters which support an associative mechanism in the transition states and the higher rate of substitution of the dha in Fe(dha) 3 complex is due to entropy effect. The solid complexes were synthesized and characterized by elemental analysis, IR and UV-vis spectral techniques.

Strong Photo-Amplification Effects in Flexible Organic Capacitors with Small Molecular Solid-State Electrolyte Layers Sandwiched between Photo-Sensitive Conjugated Polymer Nanolayers

PubMed Central

Lee, Hyena; Kim, Jungnam; Kim, Hwajeong; Kim, Youngkyoo

2016-01-01

We demonstrate strong photo-amplification effects in flexible organic capacitors which consist of small molecular solid-state electrolyte layers sandwiched between light-sensitive conjugated polymer nanolayers. The small molecular electrolyte layers were prepared from aqueous solutions of tris(8-hydroxyquinoline-5-sulfonic acid) aluminum (ALQSA3), while poly(3-hexylthiophene) (P3HT) was employed as the light-sensitive polymer nanolayer that is spin-coated on the indium-tin oxide (ITO)-coated poly(ethylene terephthalate) (PET) film substrates. The resulting capacitors feature a multilayer device structure of PET/ITO/P3HT/ALQSA3/P3HT/ITO/PET, which were mechanically robust due to good adhesion between the ALQSA3 layers and the P3HT nanolayers. Results showed that the specific capacitance was increased by ca. 3-fold when a white light was illuminated to the flexible organic multilayer capacitors. In particular, the capacity of charge storage was remarkably (ca. 250-fold) enhanced by a white light illumination in the potentiostatic charge/discharge operation, and the photo-amplification functions were well maintained even after bending for 300 times at a bending angle of 180o. PMID:26846891

Strong Photo-Amplification Effects in Flexible Organic Capacitors with Small Molecular Solid-State Electrolyte Layers Sandwiched between Photo-Sensitive Conjugated Polymer Nanolayers.

PubMed

Lee, Hyena; Kim, Jungnam; Kim, Hwajeong; Kim, Youngkyoo

2016-02-05

We demonstrate strong photo-amplification effects in flexible organic capacitors which consist of small molecular solid-state electrolyte layers sandwiched between light-sensitive conjugated polymer nanolayers. The small molecular electrolyte layers were prepared from aqueous solutions of tris(8-hydroxyquinoline-5-sulfonic acid) aluminum (ALQSA3), while poly(3-hexylthiophene) (P3HT) was employed as the light-sensitive polymer nanolayer that is spin-coated on the indium-tin oxide (ITO)-coated poly(ethylene terephthalate) (PET) film substrates. The resulting capacitors feature a multilayer device structure of PET/ITO/P3HT/ALQSA3/P3HT/ITO/PET, which were mechanically robust due to good adhesion between the ALQSA3 layers and the P3HT nanolayers. Results showed that the specific capacitance was increased by ca. 3-fold when a white light was illuminated to the flexible organic multilayer capacitors. In particular, the capacity of charge storage was remarkably (ca. 250-fold) enhanced by a white light illumination in the potentiostatic charge/discharge operation, and the photo-amplification functions were well maintained even after bending for 300 times at a bending angle of 180(°).

Microscopic Simulations of Charge Transport in Disordered Organic Semiconductors

PubMed Central

2011-01-01

Charge carrier dynamics in an organic semiconductor can often be described in terms of charge hopping between localized states. The hopping rates depend on electronic coupling elements, reorganization energies, and driving forces, which vary as a function of position and orientation of the molecules. The exact evaluation of these contributions in a molecular assembly is computationally prohibitive. Various, often semiempirical, approximations are employed instead. In this work, we review some of these approaches and introduce a software toolkit which implements them. The purpose of the toolkit is to simplify the workflow for charge transport simulations, provide a uniform error control for the methods and a flexible platform for their development, and eventually allow in silico prescreening of organic semiconductors for specific applications. All implemented methods are illustrated by studying charge transport in amorphous films of tris-(8-hydroxyquinoline)aluminum, a common organic semiconductor. PMID:22076120

Optical, electrical, and magnetic field studies of organic materials for light emitting diodes and photovoltaic applications

NASA Astrophysics Data System (ADS)

Basel, Tek Prasad

We studied optical, electrical, and magnetic field responses of films and devices based on organic semiconductors that are used for organic light emitting diodes (OLEDs) and photovoltaic (OPV) solar cell applications. Our studies show that the hyperfine interaction (HFI)-mediated spin mixing is the key process underlying various magnetic field effects (MFE) and spin transport in aluminum tris(8-hydroxyquinoline)[Alq3]-based OLEDs and organic spin-valve (OSV). Conductivity-detected magnetic resonance in OLEDs and magneto-resistance (MR) in OSVs show substantial isotope dependence. In contrast, isotope-insensitive behavior in the magneto-conductance (MC) of same devices is explained by the collision of spin ½ carriers with triplet polaron pairs. We used steady state optical spectroscopy for studying the energy transfer dynamics in films and OLEDs based on host-guest blends of the fluorescent polymer and phosphorescent molecule. We have also studied the magnetic-field controlled color manipulation in these devices, which provide a strong proof for the `polaron-pair' mechanism underlying the MFE in organic devices. The critical issue that hampers organic spintronics device applications is significant magneto-electroluminescence (MEL) at room temperature (RT). Whereas inorganic spin valves (ISVs) show RT magneto-resistance, MR>80%, however, the devices do not exhibit electroluminescence (EL). In contrast, OLEDs show substantive EL emission, and are particularly attractive because of their flexibility, low cost, and potential for multicolor display. We report a conceptual novel hybrid organic/inorganic spintronics device (h-OLED), where we employ both ISV with large MR at RT, and OLED that has efficient EL emission. We investigated the charge transfer process in an OPV solar cell through optical, electrical, and magnetic field measurements of thin films and devices based on a low bandgap polymer, PTB7 (fluorinated poly-thienothiophene-benzodithiophene). We found that one of the major losses that limit the power conversion efficiency of OPV devices is the formation of triplet excitons in the polymer through recombination of charge-transfer (CT) excitons at the interface, and presented a method to suppress the dissociation of CT states by incorporating the spin ½ additive, galvinoxyl in the bulk heterojunction architecture of the active organic blend layer.

Organic Light-Emitting Diodes with a Perylene Interlayer Between the Electrode-Organic Interface

NASA Astrophysics Data System (ADS)

Saikia, Dhrubajyoti; Sarma, Ranjit

2018-01-01

The performance of an organic light-emitting diode (OLED) with a vacuum-deposited perylene layer over a fluorine-doped tin oxide (FTO) surface is reported. To investigate the effect of the perylene layer on OLED performance, different thicknesses of perylene are deposited on the FTO surface and their current density-voltages (J-V), luminance-voltages (L-V) and device efficiency characteristics at their respective thickness are studied. Further analysis is carried out with an UV-visible light double-beam spectrophotometer unit, a four-probe resistivity unit and a field emission scanning electron microscope set up to study the optical transmittance, sheet resistance and surface morphology of the bilayer anode film. We used N,N'-bis(3-methyl phenyl)- N,N'(phenyl)-benzidine (TPD) as the hole transport layer, Tris(8-hydroxyquinolinato)aluminum (Alq3) as a light-emitting layer and lithium fluoride as an electron injection layer. The luminance efficiency of an OLED structure with a 9-nm-thick perylene interlayer is increased by 2.08 times that of the single-layer FTO anode OLED. The maximum value of current efficiency is found to be 5.25 cd/A.

Numerical Study on Recombination Efficiency at 4,4'-Bis(2,2'-diphenylvinyl)-1,1'-spirobiphenyl/Tris(8-quinolinolato)aluminium Interface in Organic Light Emitting Diodes

NASA Astrophysics Data System (ADS)

Hwang, Young Wook; Kim, Kwang Sik; Won, Tae Young

2013-10-01

In this paper, we report our numerical study on the electrical and optical properties of the organic light emitting diodes (OLEDs) devices with n-doped layer, which is inserted for the purpose of reducing the interface barrier height between the cathode and the electron transport layer (ETL). We performed finite element method (FEM) simulation on OLEDs in order to understand the transport behavior of carriers, recombination kinetics, and emission property. Our model includes Poisson's equation, continuity equation to account for behavior of electrons and holes and exciton continuity/transfer equation to account for recombination of carriers. We employ the multilayer structure which consists of indium tin oxide (ITO); 2,2',7,7'-tetrakis(N,N-diphenylamine)-9,9'-spirobi-fluorene (S-TAD); 4,4'-bis(2,2'-diphenylvinyl)-1,1'-spirobiphenyl (S-DPVBi); tris(8-quinolinolato)aluminium (Alq3); calcium (Ca).

Dual beam organic depth profiling using large argon cluster ion beams

PubMed Central

Holzweber, M; Shard, AG; Jungnickel, H; Luch, A; Unger, WES

2014-01-01

Argon cluster sputtering of an organic multilayer reference material consisting of two organic components, 4,4′-bis[N-(1-naphthyl-1-)-N-phenyl- amino]-biphenyl (NPB) and aluminium tris-(8-hydroxyquinolate) (Alq3), materials commonly used in organic light-emitting diodes industry, was carried out using time-of-flight SIMS in dual beam mode. The sample used in this study consists of a ∽400-nm-thick NPB matrix with 3-nm marker layers of Alq3 at depth of ∽50, 100, 200 and 300 nm. Argon cluster sputtering provides a constant sputter yield throughout the depth profiles, and the sputter yield volumes and depth resolution are presented for Ar-cluster sizes of 630, 820, 1000, 1250 and 1660 atoms at a kinetic energy of 2.5 keV. The effect of cluster size in this material and over this range is shown to be negligible. © 2014 The Authors. Surface and Interface Analysis published by John Wiley & Sons Ltd. PMID:25892830

A numerical study on the charge transport in TPD/Alq3-based organic light emitting diodes.

PubMed

Kim, K S; Hwang, Y W; Lee, H G; Won, T Y

2014-08-01

We report our simulation study on the charge transport characteristic of the multi-layer structure for organic light emitting diodes (OLEDs). We performed a numerical simulation on a multilayer structure comprising a hole transport layer (HTL), an emission layer (EML), and an electron transport layer (ETL) between both electrodes. The material of the HTL is TPD (N,N'-Bis (3-methylphenyl)-N,N'-bis(phenyl) benzidine), and the ETL includes Alq3 (Tris (8-hyroxyquinolinato) aluminium). Here, we investigated the parameters such as recombination rates which influence the efficiency of the charge transport between layers in bilayer OLEDs. We also analyzed a transient response during the turn on/off period and the carrier transport in accordance with the variation of the injection barrier and applied voltage. In addition, our numerical simulation revealed that the insertion of the EML affects the photonic characteristics in bilayer structure and also the efficiency due to the difference in the internal barrier height.

Solution processable 2-(trityloxy)ethyl and tert-butyl group containing amorphous molecular glasses of pyranylidene derivatives with light-emitting and amplified spontaneous emission properties

NASA Astrophysics Data System (ADS)

Zarins, Elmars; Vembris, Aivars; Misina, Elina; Narels, Martins; Grzibovskis, Raitis; Kokars, Valdis

2015-11-01

Small organic molecules with incorporated 4H-pyran-4-ylidene (pyranylidene) fragment as the π-conjugation system which bonds the electron acceptor fragment (A) with electron donor part (D) in the molecule - also well known as derivatives of 4-(dicyano-methylene)-2-methyl-6-[p-(dimethylamino)styryl]-4H-pyran (DCM) laser dye-have attracted considerable attention of scientists as potential new generation materials for organic photonics and molecular electronics due to their low-cost fabrication possibility, flexibility and low-weight. Six glassy derivatives of 4H-pyran-4-ylidene (pyranylidene) with attached bulky 2-(trityloxy)ethyl and tert-butyl groups are described in this report. Almost all of the synthesized compounds form good optical quality transparent amorphous films from volatile organic solvents and could be obtained in good yields up to 75%. Their light emission in solution and thin solid films is in the range of 600-700 nm, they are thermally stable and show glass transition in the range of 108-158 °C. The amplified spontaneous emission threshold values of the neat films of the glassy pyranylidene derivatives vary from 155 to 450 μJ/cm2 and their HOMO and LUMO energy levels are between of those of tris(8-hydroxy quinolinato) aluminum (Alq3). The photoluminescence quantum yields of the glassy compounds are in the range from 1% to about 7.7% and their electroluminescence properties have been investigated. Therefore, glassy pyranylidene derivatives could be a very potential low-cost solution processable materials for Alq3 hosted light-amplification and light-emitting application studies.

Highly selective and sensitive fluorescent paper sensor for nitroaromatic explosive detection.

PubMed

Ma, Yingxin; Li, Hao; Peng, Shan; Wang, Leyu

2012-10-02

Rapid, sensitive, and selective detection of explosives such as 2,4,6-trinitrotoluene (TNT) and 2,4,6-trinitrophenol (TNP), especially using a facile paper sensor, is in high demand for homeland security and public safety. Although many strategies have been successfully developed for the detection of TNT, it is not easy to differentiate the influence from TNP. Also, few methods were demonstrated for the selective detection of TNP. In this work, via a facile and versatile method, 8-hydroxyquinoline aluminum (Alq(3))-based bluish green fluorescent composite nanospheres were successfully synthesized through self-assembly under vigorous stirring and ultrasonic treatment. These polymer-coated nanocomposites are not only water-stable but also highly luminescent. Based on the dramatic and selective fluorescence quenching of the nanocomposites via adding TNP into the aqueous solution, a sensitive and robust platform was developed for visual detection of TNP in the mixture of nitroaromatics including TNT, 2,4-dinitrotoluene (DNT), and nitrobenzene (NB). Meanwhile, the fluorescence intensity is proportional to the concentration of TNP in the range of 0.05-7.0 μg/mL with the 3σ limit of detection of 32.3 ng/mL. By handwriting or finger printing with TNP solution as ink on the filter paper soaked with the fluorescent nanocomposites, the bluish green fluorescence was instantly and dramatically quenched and the dark patterns were left on the paper. Therefore, a convenient and rapid paper sensor for TNP-selective detection was fabricated.

Molecular mechanics approach for design and conformational studies of macrocyclic ligands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rohini,; Akbar, Rifat; Kanungo, B. K., E-mail: b.kanungo@gmail.com

2015-08-28

Computational Chemistry has revolutionized way of viewing molecules at the quantum mechanical scale by allowing simulating various chemical scenarios that are not possible to study in a laboratory. The remarkable applications of computational chemistry have promoted to design and test of the effectiveness of various methods for searching the conformational space of highly flexible molecules. In this context, we conducted a series of optimization and conformational searches on macrocyclic based ligands, 9N3Me5Ox, (1,4,7-tris(5-methyl-8-hydroxyquinoline)-1,4,7-triazacyclononane) and 12N3Me5Ox, (1,5,9-tris(5-methyl-8-hydroxyquinoline)-1,5,9-triazacyclododecane) and studied their selectivity and coordination behavior with some lanthanide metal ions in molecular mechanics and semiempirical methods. The methods include both systematic andmore » random conformational searches for dihedral angles, torsion angles and Cartesian coordinates. Structural studies were carried out by using geometry optimization, coordination scans and electronic properties were evaluated. The results clearly show that chair-boat conformational isomer of 9N3Me5Ox ligand is more stable due to lower eclipsing ethane interaction and form stronger adduct complexes with lanthanide metal ion. This is because of the fact that, in a central unit of 9N3 of the ligand form six endo type bonds out of nine. The rest of bonds have trans conformation. In contrast, for the adduct of 12N3Me5Ox, two C-C bonds have on eclipsed conformation, and others have synclinal and antiperiplanar confirmations. The distortion of the two eclipsed conformations may affect the yields and the stability of the complexes.« less

Index matching of TE and TM modes in organic multilayer waveguides

NASA Astrophysics Data System (ADS)

Thompson, Jonathan; Schmitzer, Heidrun; Wagner, Hans Peter

We investigate transverse electric (TE) and magnetic (TM) mode propagation in organic multilayers consisting of aluminum quinoline (Alq3) and perylenetetracarboxylic dianhydride (PTCDA). In particular, we analyze two multilayer waveguides, Alq3-PTCDA-Alq3 and PTCDA-Alq3-PTCDA, engineered to give index matching according to modeling. The waveguides were grown on a glass substrate via organic molecular beam deposition. Fabry-Perot oscillations observed from reflection measurements were used to confirm the individual layer thicknesses. We were able to observe refractive index matching between TE0 and TE1, as well as TE2 and TE3 modes for the PTCDA-Alq3-PTCDA waveguide due to the light propagation through the top and bottom PTCDA layers, respectively. In addition, we were able to match TE1 and TM1, as well as TE3 and TM3 modes in the Alq3-PTCDA-Alq3 multilayer due to the birefringence of the PTCDA layer. Furthermore, we are able to create mode matching for a range of wavelengths due to the similar effective refractive index dispersion of different waveguide modes. The ability to phase match different waveguide modes opens a wide range of potential applications including polarization-insensitive propagation and mode switching by adding a thin magnetic metal film within the waveguide and applying an external magnetic field.

Exciton Emission from Bare and Alq3/Gold Coated GaN Nanorods

NASA Astrophysics Data System (ADS)

Mohammadi, Fatemesadat; Kuhnert, Gerd; Hommel, Detlef; Schmitzer, Heidrun; Wagner, Hans-Peter

We study the excitonic and impurity related emission in bare and aluminum quinoline (Alq3)/gold coated wurtzite GaN nanorods by temperature-dependent time-integrated (TI) and time-resolved (TR) photoluminescence (PL). The GaN nanorods were grown by molecular beam epitaxy. Alq3 as well as Alq3/gold covered nanorods were synthesized by organic molecular beam deposition. In the near-band edge region a donor-bound-exciton (D0X) emission is observed at 3.473 eV. Another emission band at 3.275 eV reveals LO-phonon replica and is attributed to a donor-acceptor-pair (DAP) luminescence. TR PL traces at 20 K show a nearly biexponential decay for the D0X with lifetimes of approximately 180 and 800 ps for both bare and Alq3 coated nanorods. In GaN nanorods which were coated with an Alq3 film and subsequently with a 10 nm thick gold layer we observe a PL quenching of D0X and DAP band and the lifetimes of the D0X transition shorten. The quenching behaviour is partially attributed to the energy-transfer from free excitons and donor-bound-excitons to plasmon oscillations in the gold layer.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carvalho, R. S.; Ávila, H. C.; Cremona, M., E-mail: cremona@fis.puc-rio.br

The recently discovered organic magnetoresistance effect (OMAR) reveals the spin-dependent behavior of the charge transport in organic semiconductors. So far, it is known that hyperfine interactions play an important role in this phenomenon and also that spin-orbit coupling is negligible for light-atom based compounds. However, in the presence of heavy atoms, spin-orbit interactions should play an important role in OMAR. It is known that these interactions are responsible for singlet and triplet states mixing via intersystem crossing and the change of spin-charge relaxation time in the charge mobility process. In this work, we report a dramatic change in the OMARmore » effect caused by the presence of strong intramolecular spin-orbit coupling in a series of rare-earth quinolate organic complex-based devices. Our data show a different OMAR lineshape compared with the OMAR lineshape of tris(8-hydroxyquinolinate) aluminum-based devices, which are well described in the literature. In addition, electronic structure calculations based on density functional theory help to establish the connection between this results and the presence of heavy central ions in the different complexes.« less

The determination of aluminum, copper, iron, and lead in glycol formulations by atomic absorption spectroscopy

NASA Technical Reports Server (NTRS)

1977-01-01

Initial screening tests and the results obtained in developing procedures to determine Al, Cu, Fe, and Pb in glycol formulations are described. Atomic absorption completion was selected for Cu, Fe and Pb, and after comparison with emission spectroscopy, was selected for Al also. Before completion, carbon, iron, and lead are extracted with diethyl dithio carbamate (DDC) into methyl isobutyl ketone (MIBK). Aluminum was also extracted into MIBK using 8-hydroxyquinoline as a chelating agent. As little as 0.02 mg/l carbon and 0.06 mg/l lead or iron may be determined in glycol formulations. As little as 0.3 mg/l aluminum may be determined.

Generation of DNA profiles from fingerprints developed with columnar thin film technique.

PubMed

Plazibat, Stephanie L; Roy, Reena; Swiontek, Stephen E; Lakhtakia, Akhlesh

2015-12-01

Partial-bloody fingerprints and partial fingerprints with saliva are often encountered at crime scenes, potentially enabling the combination of fingerprint and DNA analyses for absolute identification, provided that the development technique for fingerprint analysis does not inhibit DNA analysis. 36 partial-bloody fingerprints and 30 fingerprints wetted with saliva, all deposited on brass, were first developed using the columnar-thin-film (CTF) technique and then subjected to short tandem repeat (STR) DNA analysis. Equal numbers of samples were subjected to the same DNA analysis without development. Tris (8-hydroxyquinolinato) aluminum, or Alq3, was evaporated to deposit CTFs for development of the prints. DNA was extracted from all 132 samples, quantified, and amplified with AmpFlSTR(®) Identifiler Plus Amplification Kit. Additionally, DNA analyses were conducted on four blood smears on un-fingerprinted brass that had been subjected to CTF deposition and four blood smears on un-fingerprinted brass that had not been subjected to CTF deposition. Complete and concordant autosomal STR profiles of the same quality were obtained from both undeveloped and CTF-developed fingerprints, indicating that CTF development of fingerprints preserves DNA and does not inhibit subsequent DNA analysis. Even when there were no fingerprints, CTF deposition did not lead to inhibition of DNA analysis. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Understanding the role of electron and hole trions on current transport in aluminium tris(8-hydroxyquinoline) using organic magnetoresistance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Sijie; Gillin, W. P., E-mail: w.gillin@qmul.ac.uk; Materials Research Institute and School of Physics and Astronomy, Queen Mary University of London, Mile End Road, London E1 4NS

The change in current through an organic light emitting diode (OLED) when it is placed in a magnetic field has been dubbed organic magnetoresistance and provides a means to understand the spin interactions that are occurring in working devices. Whilst there are a wide range of interactions that have been proposed to be the cause of the measured effects, there is still a need to identify their individual roles and in particular how they respond to an applied magnetic field. In this work, we investigate the effect of changing the balance of electron and hole injection in a simple aluminiummore » tris(8-hydroxyqinoline) based OLED and demonstrate that the triplet polaron interaction appears to be much stronger for electrons than for holes in this material.« less

Photometric flow injection determination of phosphate on a PDMS microchip using an optical detection system assembled with an organic light emitting diode and an organic photodiode.

PubMed

Liu, Rong; Ishimatsu, Ryoichi; Yahiro, Masayuki; Adachi, Chihaya; Nakano, Koji; Imato, Toshihiko

2015-01-01

A compact photometric detector was constructed from an organic light emitting diode (OLED) based on a europium complex, europium(diben-zoylmethanato)3(bathophenanthroline) (Eu(DBM)3bath), as the light source and an organic photodiode (OPD) fabricated from a hetero-junction of two layers of copper phthalocyanine (CuPc)/fullerene (C60) as the photo-detector on a microchip prepared from poly(dimethylsiloxan) (PDMS) and was applied to the determination of phosphate. The OLED and the OPD were fabricated by a vapor deposition method on an indium tin oxide (ITO) coated glass substrate with the following layered structure; Glass (0.7 mm)/ITO (110 nm)/4,4'-bis[N-(1-naphthyl)-N-phenyl amino]-biphenyl (α-NPD) (30 nm)/4,4'-di(N-carbazolyl)biphenyl (CBP): Eu(3+) (8 wt%, 30 nm)/bathocuproine (BCP) (30 nm)/aluminum tris(8-hydroxyquinoline) (Alq3) (25 nm)/magnesium and silver (MgAg) (100 nm)/Ag (10nm) and Glass (0.7 mm)/ITO (110 nm)/CuPc (35 nm)/C60 (50 nm)/BCP (10 nm)/Ag (50 nm), respectively. The OLED based on the europium complex emitted a sharp light at the wavelength of 612 nm with a full width at half maximum (FWHM) of 8 nm. The performance of the photometric detector assembled was evaluated based on measurements of the absorbance of different concentrations of malachite green (MG) solutions for a batch system with 1cm long path length. The molar absorptive coefficient of the MG solution, calculated from the photocurrent of the OPD, was in good agreement with the value reported in the literature. A microchip with two inlets and one outlet U-shaped channel was prepared by a conventional photolithograph method. The OLED and the OPD were configured so as to face each other through the PDMS microchip in parallel in order to align the light axis of the OLED and the OPD with the flow cell (optical path length of 5mm), which was located at the end of outlet. For the determination of phosphate, an ion-association reaction between MG and a molybdenum-phosphate complex was utilized and a good linear relationship between the concentration and absorbance was observed in the concentration range 0-0.2 ppm, with a detection limit (S/N=3) of 0.02 ppm. The assembled photometric detector was also applied to the determination of phosphate by the flow injection of river water samples using the reagent solution containing MG and molybdenum ammonium in sulfuric acid. A good recovery (97-99%) for the river water samples, which had been spiked with the standard 0.08 ppm, with an RSD of ca 5% (n=5) was obtained using the constructed system. Copyright © 2014 Elsevier B.V. All rights reserved.

Controlling the exciton emission of gold coated GaAs-AlGaAs core-shell nanowires with an organic spacer layer

NASA Astrophysics Data System (ADS)

Kaveh, M.; Gao, Q.; Jagadish, C.; Ge, J.; Duscher, G.; Wagner, H. P.

2016-12-01

Excitons are the most prominent optical excitations and controlling their emission is an important step towards new optical devices. We have investigated the exciton emission from uncoated and gold/aluminum quinoline (Alq3) coated GaAs-AlGaAs-GaAs core-shell nanowires (NWs) using temperature-, intensity- and polarization dependent photoluminescence (PL). Plasmonic GaAs-AlGaAs-GaAs NWs with a ˜10 nm thick Au coating but without an Alq3 spacer layer reveal a significant reduction of the PL intensity of the exciton emission compared with the uncoated NW sample. Plasmonic NW samples with the same nominal Au coverage and an additional Alq3 interlayer of 3 or 6 nm thickness show a clearly stronger PL intensity which increases with rising Alq3 spacer thickness. Time-resolved (TR) PL measurements reveal an increase of the exciton decay rate by a factor of up to two with decreasing Alq3 spacer thickness suggesting the presence of Förster energy transfer from NW excitons to plasmon oscillations in the gold film. The weak change of the decay time, however, indicates that Förster energy-transfer is only partially responsible for the PL quenching in the gold coated NWs. The main reason for the reduction of the PL emission is attributed to a gold induced band-bending in the GaAs NW core which causes exciton dissociation. With increasing Alq3 spacer thickness the band-bending decreases leading to a reduction of the exciton dissociation and PL quenching. Our interpretation is supported by electron energy loss spectroscopy measurements which show a signal reduction and blue shift of defect (possibly EL2) transitions when gold particles are deposited on NWs compared with bare or Alq3 coated NWs.

Controlling the exciton emission of gold coated GaAs-AlGaAs core-shell nanowires with an organic spacer layer.

PubMed

Kaveh, M; Gao, Q; Jagadish, C; Ge, J; Duscher, G; Wagner, H P

2016-12-02

Excitons are the most prominent optical excitations and controlling their emission is an important step towards new optical devices. We have investigated the exciton emission from uncoated and gold/aluminum quinoline (Alq 3 ) coated GaAs-AlGaAs-GaAs core-shell nanowires (NWs) using temperature-, intensity- and polarization dependent photoluminescence (PL). Plasmonic GaAs-AlGaAs-GaAs NWs with a ∼10 nm thick Au coating but without an Alq 3 spacer layer reveal a significant reduction of the PL intensity of the exciton emission compared with the uncoated NW sample. Plasmonic NW samples with the same nominal Au coverage and an additional Alq 3 interlayer of 3 or 6 nm thickness show a clearly stronger PL intensity which increases with rising Alq 3 spacer thickness. Time-resolved (TR) PL measurements reveal an increase of the exciton decay rate by a factor of up to two with decreasing Alq 3 spacer thickness suggesting the presence of Förster energy transfer from NW excitons to plasmon oscillations in the gold film. The weak change of the decay time, however, indicates that Förster energy-transfer is only partially responsible for the PL quenching in the gold coated NWs. The main reason for the reduction of the PL emission is attributed to a gold induced band-bending in the GaAs NW core which causes exciton dissociation. With increasing Alq 3 spacer thickness the band-bending decreases leading to a reduction of the exciton dissociation and PL quenching. Our interpretation is supported by electron energy loss spectroscopy measurements which show a signal reduction and blue shift of defect (possibly EL2) transitions when gold particles are deposited on NWs compared with bare or Alq 3 coated NWs.

The determination of specific forms of aluminum in natural water

USGS Publications Warehouse

Barnes, R.B.

1975-01-01

A procedure for analysis and pretreatment of natural-water samples to determine very low concentrations of Al is described which distinguishes the rapidly reacting equilibrium species from the metastable or slowly reacting macro ions and colloidal suspended material. Aluminum is complexed with 8-hydroxyquinoline (oxine), pH is adjusted to 8.3 to minimize interferences, and the aluminum oxinate is extracted with methyl isobutyl ketone (MIBK) prior to analysis by atomic absorption. To determine equilibrium species only, the contact time between sample and 8-hydroxyquinoline is minimized. The Al may be extracted at the sample site with a minimum of equipment and the MIBK extract stored for several weeks prior to atomic absorption analysis. Data obtained from analyses of 39 natural groundwater samples indicate that filtration through a 0.1-??m pore size filter is not an adequate means of removing all insoluble and metastable Al species present, and extraction of Al immediately after collection is necessary if only dissolved and readily reactive species are to be determined. An average of 63% of the Al present in natural waters that had been filtered through 0.1-??m pore size filters was in the form of monomeric ions. The total Al concentration, which includes all forms that passed through a 0.1-??m pore size filter, ranged 2-70 ??g/l. The concentration of Al in the form of monomeric ions ranged from below detection to 57 ??g/l. Most of the natural water samples used in this study were collected from thermal springs and oil wells. ?? 1975.

Photoluminescence and Coordination Behaviour of Lanthanide Complexes of Tris (Aminomethyl)Ethane-5-Oxine in Aqueous Solution.

PubMed

Akbar, Rifat; Baral, Minati; Kanungo, B K

2017-01-01

Photophysical properties of a multidentate tripodal ligand, 5,5'-(2-(((8-hydroxyquinolin-5-yl) methylamino)methyl)-2-methylpropane-1,3-diyl) bis (azanediyl)bis (methylene)diquinolin-8-ol, (TAME5OX), with La 3+ and Er 3+ ions have been examined for photonics applications. The change in behavior in electronic spectra of these complexes reveals the use of TAME5OX as a sensitive optical pH based sensor to detect Ln 3+ ions whereas indication of strong green fluorescence allows simultaneous sensing within the visible region in competitive medium. The intense fluorescence intermittently gets quenched under acidic and basic conditions due to photoinduced intramolecular electron transfer from the excited 8-hydroxyquinoline (8-HQ) moiety to the metal ion. This renders these compounds the OFF-ON-OFF type of pH-dependent fluorescent sensor. The thermodynamic stability and coordination behaviour of the chelator with the said lanthanide ions have also been probed by potentiometric, UV - visible and fluorescence spectrophotometric method. TAME5OX forms protonated complex [Ln (H 4 L)] 4+ below pH ~4.0 which sequentially deprotonates through one proton process with increase of pH. The stability constants of neutral complexes have been determined to be in the range log β 110  = 32-34 and pLn in the range of 14-20, indicating TAME5OX is a good synthetic lanthanide chelator. Theoretical spectra were also calculated by ZINDO/s methodology at single excitations (CIS) level on PM7 as sparkle energy-minimized geometries.

Numerical study on exciton transport and light emission for organic light emitting diodes with an emission layer.

PubMed

Kim, K S; Hwang, Y W; Won, T Y

2013-12-01

This paper reports the results of a numerical study on carrier injection and exciton transport in an organic light emitting diode (OLED) structure based on tris (8-hydroxyquinolinato) aluminum (Alq3). Because charge accumulation at the interfaces between the emission layer (EML) and transport layer are believed to increase the recombination rate, which also increases the exciton density, a numerical study was performed on the effect of inserting an EML in the bilayer structure. In the first case considered, the lowest unoccupied molecular orbital (LUMO) of the EML was aligned with the LUMO of the hole transport layer (HTL), whereas the highest occupied molecular orbital (HOMO) of the EML was aligned with the HOMO of the electron transport layer (ETL). In the second case, the LUMO of the EML was aligned with the LUMO of the ETL and the HOMO of the EML was aligned with the HOMO of the HTL. In case of a charge-blocking device, most of the recombination appeared to occur at both edges of the EML because the electric field exhibited a peak in these areas. On the other hand, in the case of the charge-confining device, the electric field was confined at the interface between the EML and ETL. This paper also discussed the effect of the insertion of a doping layer as transport layer.

A flexible plasma-treated silver-nanowire electrode for organic light-emitting devices.

PubMed

Li, Jun; Tao, Ye; Chen, Shufen; Li, Huiying; Chen, Ping; Wei, Meng-Zhu; Wang, Hu; Li, Kun; Mazzeo, Marco; Duan, Yu

2017-11-28

Silver nanowires (AgNWs) are a promising candidate to replace indium tin oxide (ITO) as transparent electrode material. However, the loose contact at the junction of the AgNWs and residual surfactant polyvinylpyrrolidone (PVP) increase the sheet resistance of the AgNWs. In this paper, an argon (Ar) plasma treatment method is applied to pristine AgNWs to remove the PVP layer and enhance the contact between AgNWs. By adjusting the processing time, we obtained AgNWs with a sheet resistance of 7.2Ω/□ and a transmittance of 78% at 550 nm. To reduce the surface roughness of the AgNWs, a peel-off process was used to transfer the AgNWs to a flexible NOA63 substrate. Then, an OLED was fabricated with the plasma-treated AgNWs electrode as anode. The highest brightness (27000 cd/m 2 ) and current efficiency (11.8 cd/A) was achieved with a 30 nm thick light emitting layer of tris-(8-hydroxyquinoline) aluminum doped with 1% 10-(2-benzothiazolyl)-2,3,6,7-tetrahydro-1,1,7,7-tetramethyl-1H,5 H,11H-(1)-benzopyropyrano(6,7-8-I,j)quinolizin-11-one. Compared to thermal annealing, the plasma-treated AgNW film has a lower sheet resistance, a shorter processing time, and a better hole-injection. Our results indicate that plasma treatment is an effective and efficient method to enhance the conductivity of AgNW films, and the plasma-treated AgNW electrode is suitable to manufacture flexible organic optoelectronic devices.

Electrochemical models for the radical annihilation reactions in organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Armstrong, Neal R.; Anderson, Jeffrey D.; Lee, Paul A.; McDonald, Erin; Wightman, R. M.; Hall, Hank K.; Hopkins, Tracy; Padias, Anne; Thayumanavan, Sankaran; Barlow, Stephen; Marder, Seth R.

1998-12-01

Bilayer organic light emitting diodes (OLEDs), based upon vacuum deposited molecules, or single layer OLEDs, based upon spin-cast polymeric materials, doped with these same molecules, produce light from emissive states of the lumophores which are created through annihilation reactions of radical species, which can be modeled through solution electrochemistry. Difference seen in solution reduction and oxidation potentials of molecular components of OLEDs are a lower limit estimate to the differences in energy of these same radical species in the condensed phase environmental. The light emitted from an aluminum quinolate (Alq3)/triarylamine (TPD)-based OLED, or an Alq3/PVK single layers OLED, can be reproduce from solution cross reactions of Alq3/TPD+. The efficiency of this process increases as the oxidation potential of the TPD increases, due to added substituents. Radical cations and anions of solubilized version of quinacridone dopants (DIQA) which have been used to enhance efficiencies in these OLEDs, are shown to be electrochemically more stable than Alq3 and Alq3, and DIQA radical annihilation reactions produce the same emissive state as in the quinacridone-doped OLEDs. Electrochemical studies demonstrate the ways in which other dopants might enhance the efficiency and shift the color output of OLEDs, across the entire visible and near-IR spectrum. Chemical degradation pathways of these same molecular components, which they may undergo during OLED operation, are also revealed by these electrochemical studies.

Observation of hole hopping via dopant in MoOx-doped organic semiconductors: Mechanism analysis and application for high performance organic light-emitting devices

NASA Astrophysics Data System (ADS)

Qiao, Xianfeng; Chen, Jiangshan; Li, Xinglin; Ma, Dongge

2010-05-01

Conduction mechanism in molybdenum trioxide (MoOx)-doped hole- and electron-type organic semiconductors is investigated. The used hole-transporting materials are N ,N'-diphenyl-N ,N'-bis(1-naphthylphenyl)-1, 1'-biphen4, 4'-diamine, 4',4″-tri(N-carbazolyl)triphenylamine, 4, 4'-N,N-dicarbazole-biphenyl, and pentacene and the used electron-transporting material is (8-quinolinolato) aluminum (Alq3). It can be seen that the hole conductivity is significantly enhanced upon MoOx doping, and more importantly, dominant hole current could be realized in a typical electron-transport material Alq3 by doping MoOx. Hence, high efficiency organic light-emitting devices can also be achieved even using MoOx-doped Alq3 film as hole transporting layer. The mechanism investigation indicates that the MoOx plays an important role in the hole transport. It is showed that the MoOx serves as the hole hopping sites, whereas the used organic materials serve as the transport medium and determine the magnitude of transport current. Furthermore, it is found that doping MoOx into the organic materials also reduces the energy and position disorders of the doped organic films, which are well demonstrated by the study on transport characteristics of the doped films at various temperatures.

40 CFR 180.415 - Aluminum tris (O-ethylphosphonate); tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Lingonberry 40 None Nut, macadamia 0.20 None Onion, green 10.0 None Pea, succulent 0.3 None Pineapple 0.1 None... Vegetable, cucurbit, group 9 15 None Vegetable, leafy, except brassica, group 4 100 None (b) Section 18... registration, as defined in § 180.1(n), are established for residues of the fungicide aluminum tris (O...

Polymers Containing Diphenylvinyl-Substituted Indole Rings as Charge-Transporting Materials for OLEDs

NASA Astrophysics Data System (ADS)

Grigalevicius, S.; Zostautiene, R.; Sipaviciute, D.; Stulpinaite, B.; Volyniuk, D.; Grazulevicius, J. V.; Liu, L.; Xie, Z.; Zhang, B.

2016-02-01

Monomers and polymers containing electronically isolated diphenylvinyl-substituted indole rings were synthesized and characterized by nuclear magnetic resonance (NMR) and mass spectroscopies as well as by gel permeation chromatography. The polymers represent amorphous materials with glass transition temperatures of 91-109°C and thermal decomposition starting above 307°C. Electron photoemission spectra of thin films of the synthesized polymers revealed ionization potentials of 5.54-5.58 eV. The synthesized polymers were tested as hole-transporting materials in simple electroluminescent organic light-emitting diode (OLED) devices with tris(quinolin-8-olato)aluminium (Alq3) as an emitter as well as an electron-transporting layer. A green OLED device containing a hole-transporting layer of poly[1-(2,3-epithiopropyl)-2-methyl-3-(2,2-diphenylvinyl)índole] exhibited the best overall performance with a driving voltage of 4.0 V, maximum photometric efficiency of 2.8 cd/A and maximum brightness of about 4200 cd/m2.

Synthesis and characterization of 8-hydroxyquinoline complexes of tin(IV) and their application in organic light emitting diode.

PubMed

Fazaeli, Yousef; Amini, Mostafa M; Najafi, Ezzatollah; Mohajerani, Ezeddin; Janghouri, Mohammad; Jalilian, Amirreza; Ng, Seik Weng

2012-09-01

A series of 8-hydroxyquinoline complexes of tin, Q(2)SnCl(2) (Q = 2-methyl-8-hydroxyquinoline, 8-hydroxyquinoline, 5,7-dibromo-8-hydroxyquinoline, 5-chloro-8-hydroxyquinoline, 5,7-dichloro-8-hydroxyquinoline and 5-nitro-8-hydroxyquinoline) were prepared by reacting stannous dichloride with 8-hydroxyquinoline and its derivatives. All complexes were characterized by elemental analysis, mass spectrometry and infrared, UV-vis and (1)H NMR spectroscopes. Furthermore, the molecular structure of a representative complex, dichlorido-bis(5-nitro-quinolin-8-olato-2N,O)tin(IV), was determined by single-crystal X-ray diffraction. The photoluminescence (PL) properties of all prepared compounds and electroluminescence (EL) property of a selected complex (Q = 5-chloro-8-hydroxyquinoline) were investigated. The results showed that the emission wavelength can be tuned by electron donating or withdrawing group substituent on 8-hydroxyquinoline. Application of prepared complexes in fabrication of an OLED has been demonstrated.

Speciation of aluminum in drink samples by 8-hydroxyquinoline loaded silylanization silica gel microcolumn separation with off-line ICP-MS detection.

PubMed

Chen, Jie; Huang, Chaozhang; Hu, Bin; Jiang, Zucheng

2004-11-17

A technique using a flow injection microcolumn separation coupled with ICP-MS detection has been developed for the speciation of Al in drink samples. The retention behaviors of different Al species were studied with 8-hydroxyquinoline (8-HQ) loaded silylanization silica gel as the packing material and inorganic acid (HNO3) as the elution. The results indicated that in a pH range of 5.0 to 8.0, all labile monomeric Al species were retained on the microcolumn while nonlabile monomeric Al species were directly passed through the column. Various Al species after separation were detected by ICP-MS. The detection limit of 0.2 ng mL(-1) and a relative standard deviation (RSD) of 4.2% at 10 ng mL(-1) (n = 11) were achieved, and the recoveries for the spiked samples were 95-108%. The proposed method has been applied to the analysis of Al species in tea infusions, coffee, and tap waters with satisfactory results. The results obtained by this method were compared with that obtained by the cation exchange microcolumn separation and ICP-MS detection system, and some valuable conclusions were drawn.

Structurally integrated organic light emitting device-based sensors for gas phase and dissolved oxygen.

PubMed

Shinar, Ruth; Zhou, Zhaoqun; Choudhury, Bhaskar; Shinar, Joseph

2006-05-24

A compact photoluminescence (PL)-based O2 sensor utilizing an organic light emitting device (OLED) as the light source is described. The sensor device is structurally integrated. That is, the sensing element and the light source, both typically thin films that are fabricated on separate glass substrates, are attached back-to-back. The sensing elements are based on the oxygen-sensitive dyes Pt- or Pd-octaethylporphyrin (PtOEP or PdOEP, respectively), which are embedded in a polystyrene (PS) matrix, or dissolved in solution. Their performance is compared to that of a sensing element based on tris(4,7-diphenyl-l,10-phenanthroline) Ru II (Ru(dpp)) embedded in a sol-gel film. A green OLED light source, based on tris(8-hydroxy quinoline Al (Alq3), was used to excite the porphyrin dyes; a blue OLED, based on 4,4'-bis(2,2'-diphenylviny1)-1,1'-biphenyl, was used to excite the Ru(dpp)-based sensing element. The O2 level was monitored in the gas phase and in water, ethanol, and toluene solutions by measuring changes in the PL lifetime tau of the O2-sensitive dyes. The sensor performance was evaluated in terms of the detection sensitivity, dynamic range, gas flow rate, and temperature effect, including the temperature dependence of tau in pure Ar and O2 atmospheres. The dependence of the sensitivity on the preparation procedure of the sensing film and on the PS and dye concentrations in the sensing element, whether a solid matrix or solution, were also evaluated. Typical values of the detection sensitivity in the gas phase, S(g) identical with tau(0% O2)/tau(100% O2), at 23 degrees C, were approximately 35 to approximately 50 for the [Alq3 OLED[/[PtOEP dye] pair; S(g) exceeded 200 for the Alq3/PdOEP sensor. For dissolved oxygen (DO) in water and ethanol, S(DO) (defined as the ratio of tau in de-oxygenated and oxygen-saturated solutions) was approximately 9.5 and approximately 11, respectively, using the PtOEP-based film sensor. The oxygen level in toluene was measured with PtOEP dissolved directly in the solution. That sensor exhibited a high sensitivity, but a limited dynamic range. Effects of aggregation of dye molecules, sensing film porosity, and the use of the OLED-based sensor arrays for O2 and multianalyte detection are also discussed.

Electrochemistry and spectroelectrochemistry of bioactive hydroxyquinolines: a mechanistic study.

PubMed

Sokolová, Romana; Nycz, Jacek E; Ramešová, Šárka; Fiedler, Jan; Degano, Ilaria; Szala, Marcin; Kolivoška, Viliam; Gál, Miroslav

2015-05-21

The oxidation mechanism of selected hydroxyquinoline carboxylic acids such as 8-hydroxyquinoline-7-carboxylic acid (1), the two positional isomers 2-methyl-8-hydroxyquinoline-7-carboxylic acid (3) and 2-methyl-5-hydroxyquinoline-6-carboxylic acid (4), as well as other hydroxyquinolines were studied in aprotic environment using cyclic voltammetry, controlled potential electrolysis, in situ UV-vis and IR spectroelectrochemistry, and HPLC-MS/MS techniques. IR spectroelectrochemistry showed that oxidation unexpectedly proceeds together with protonation of the starting compound. We proved that the nitrogen atom in the heterocycle of hydroxyquinolines is protonated during the apparent 0.7 electron oxidation process. This was rationalized by the autodeprotonation reaction by another two starting molecules of hydroxyquinoline, so that the overall oxidation mechanism involves two electrons and three starting molecules. Both the electrochemical and spectroelectrochemical results showed that the oxidation mechanism is not influenced by the presence of the carboxylic group in the chemical structure of hydroxyquinolines, as results from oxidation of 2,7-dimethyl-5-hydroxyquinoline (6). In the presence of a strong proton acceptor such as pyridine, the oxidation ECEC process involves two electrons and two protons per one molecule of the hydroxyquinoline derivative. The electron transfer efficiency of hydroxyquinolines in biosystems may be related to protonation of biocompounds containing nitrogen bases. Molecular orbital calculations support the experimental findings.

Fluorescence in complexes based on quinolines-derivatives: a search for better fluorescent probes.

PubMed

Mecca, Carolina Z P; Fonseca, Fernando L A; Bagatin, Izilda A

2016-11-05

Quinoline-derived fluorescent complexes were designed; synthesized by the reaction of 5-nitro-8-hydroxyquinoline and 5-chloro-8-hydroxyquinoline with Al(3+), Mg(2+), Zn(2+), and Cd(2+) salts (1-8); and characterized. The (1)H NMR spectra of complexes 1 and 5, containing Al(3+), were consistent with an octahedral structure having approximate D3 symmetry, and the results supported the favored facial isomer (fac). Data for complexes 2-4 and 6-8 supported the formation of tetrahedral structures. Intense luminescence was detected for complexes 5-8, even with the naked eye, as indicated by quantum yield values of 0.087, 0.094, 0.051, and 0.021, respectively. Furthermore, in contrast to 5-nitro-8-hydroxyquinoline, the 5-chloro-8-hydroxyquinoline ligand exhibited bands at different energies depending on the coordinated metal, which supported its potential application in ionic and biological probes, as well as in cell imaging. Copyright © 2016 Elsevier B.V. All rights reserved.

Emission dynamics of hybrid plasmonic gold/organic GaN nanorods

NASA Astrophysics Data System (ADS)

Mohammadi, F.; Schmitzer, H.; Kunert, G.; Hommel, D.; Ge, J.; Duscher, G.; Langbein, W.; Wagner, H. P.

2017-12-01

We studied the emission of bare and aluminum quinoline (Alq3)/gold coated wurtzite GaN nanorods by temperature- and intensity-dependent time-integrated and time-resolved photoluminescence (PL). The GaN nanorods of ˜1.5 μm length and ˜250 nm diameter were grown by plasma-assisted molecular beam epitaxy. Gold/Alq3 coated GaN nanorods were synthesized by organic molecular beam deposition. The near band-edge and donor-acceptor pair luminescence was investigated in bare GaN nanorods and compared with multilevel model calculations providing the dynamical parameters for electron-hole pairs, excitons, impurity bound excitons, donors and acceptors. Subsequently, the influence of a 10 nm gold coating without and with an Alq3 spacer layer was studied and the experimental results were analyzed with the multilevel model. Without a spacer layer, a significant PL quenching and lifetime reduction of the near band-edge emission is found. The behavior is attributed to surface band-bending and Förster energy transfer from excitons to surface plasmons in the gold layer. Inserting a 5 nm Alq3 spacer layer reduces the PL quenching and lifetime reduction which is consistent with a reduced band-bending and Förster energy transfer. Increasing the spacer layer to 30 nm results in lifetimes which are similar to uncoated structures, showing a significantly decreased influence of the gold coating on the excitonic dynamics.

Emission dynamics of hybrid plasmonic gold/organic GaN nanorods.

PubMed

Mohammadi, F; Schmitzer, H; Kunert, G; Hommel, D; Ge, J; Duscher, G; Langbein, W; Wagner, H P

2017-12-15

We studied the emission of bare and aluminum quinoline (Alq 3 )/gold coated wurtzite GaN nanorods by temperature- and intensity-dependent time-integrated and time-resolved photoluminescence (PL). The GaN nanorods of ∼1.5 μm length and ∼250 nm diameter were grown by plasma-assisted molecular beam epitaxy. Gold/Alq 3 coated GaN nanorods were synthesized by organic molecular beam deposition. The near band-edge and donor-acceptor pair luminescence was investigated in bare GaN nanorods and compared with multilevel model calculations providing the dynamical parameters for electron-hole pairs, excitons, impurity bound excitons, donors and acceptors. Subsequently, the influence of a 10 nm gold coating without and with an Alq 3 spacer layer was studied and the experimental results were analyzed with the multilevel model. Without a spacer layer, a significant PL quenching and lifetime reduction of the near band-edge emission is found. The behavior is attributed to surface band-bending and Förster energy transfer from excitons to surface plasmons in the gold layer. Inserting a 5 nm Alq 3 spacer layer reduces the PL quenching and lifetime reduction which is consistent with a reduced band-bending and Förster energy transfer. Increasing the spacer layer to 30 nm results in lifetimes which are similar to uncoated structures, showing a significantly decreased influence of the gold coating on the excitonic dynamics.

The naphthoate-modifying Cu2 +-detective Bodipy sensors with the fluorescent ON-OFF performance unaffected by molecular configuration

NASA Astrophysics Data System (ADS)

Chen, Yuting; Zhao, Luyang; Jiang, Jianzhuang

2017-03-01

Two new boron-dipyrromethenes decorated with 8-hydroxyquinoline-naphthoate moiety, namely 4,4-difluoro-8-(5-(8-hydroxyquinoline-naphthoate))-3,5-dimethyl-4-bora-3a,4a-diaza-s-indacene (8-HQ-N-DMe-Bodipy) (1) and 4,4-difluoro-8-(5-(8-hydroxyquinoline-naphthoate))-1,3,5,7-tetramethyl-4-bora-3a,4a-diaza-s-indacene (8-HQ-N-TMe-Bodipy) (2) have been synthesized. Single crystal X-ray diffraction analysis discloses the very much similar steric arrangement of 8-hydroxyquinoline-naphthoate moiety in these two compounds as revealed by the close torsion angle of C-C-O-C bridge, 174.15 and 171.81° for 1 and 2, respectively, despite the different dihedral angle between quinoline moiety and Bodipy fluorophore for 1 (73.46°) and 2 (82.26°) due to the steric hindrance originated from the C-1/C-7 methyl substituents on Bodipy core for the latter species. Systemic optical studies unravel the red-shifted absorption and fluorescence emission together with slightly lower quantum yield for 1 relative to that of 2, indicating the configuration effect on their spectroscopic properties. However, the binding of Cu2 + with hydroxyquinoline-naphthoate receptor in both 1 and 2 leads to similar fluorescent quenching characteristic due to the photo-induced electron transfer process on the basis of density functional theory calculations, suggesting their high sensitively fluorescent ON-OFF sensing potential to Cu2 + almost unaffected by molecular configuration.

Desferrioxamine and desferrioxamine-caffeine as carriers of aluminum and gallium to microbes via the Trojan Horse Effect.

PubMed

Huayhuaz, Jesus Antonio Alvarado; Vitorino, Hector Aguilar; Campos, Othon Souto; Serrano, Silvia Helena Pires; Kaneko, Telma Mary; Espósito, Breno Pannia

2017-05-01

Iron acquisition by bacteria and fungi involves in several cases the promiscuous usage of siderophores. Thus, antibiotic resistance from these microorganisms can be circumvented through a strategy of loading toxic metals into siderophores (Trojan Horse Effect). Desferrioxamine (dfo) and its cell-permeant derivative desferrioxamine-caffeine (dfcaf) were complexed with aluminum or gallium for this purpose. The complexes Me(dfo) and Me(dfcaf) (Me=Al 3+ and Ga 3+ ) were synthesized and characterized by mass spectroscopy and cyclic voltammetry. Their relative stabilities were studied through competitive equilibria with fluorescent probes calcein, fluorescein-desferrioxamine and 8-hydroxyquinoline. Me(dfo) and Me(dfcaf) were consistently more toxic than free Me 3+ against Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Candida albicans, demonstrating the Trojan Horse Effect. Wide spectrum antimicrobial action can be obtained by loading non-essential or toxic metal ions to microbes via a convenient siderophore carrier. Copyright © 2017 Elsevier GmbH. All rights reserved.

[Preparation and spectral analysis of a new type of blue light-emitting material delta-Alq3].

PubMed

Wang, Hua; Hao, Yu-ying; Gao, Zhi-xiang; Zhou, He-feng; Xu, Bing-she

2006-10-01

In the present article, delta-Alq3, a new type of blue light-emitting material, was synthesized and investigated by IR spectra, XRD spectra, UV-Vis absorption spectra, photoluminescence (PL) spectra, and electroluminescence (EL) spectra. The relationship between molecular spatial structure and spectral characteristics was studied by the spectral analysis of delta-Alq3 and alpha-Alq3. Results show that a new phase of Alq3 (delta-Alq3) can be obtained by vacuum heating alpha-Alq3, and the molecular spatial structure of alpha-Alq3 changes during the vacuum heating. The molecular spatial structure of delta-Alq3 lacks symmetry compared to alpha-Alq3. This transformation can reduce the electron cloud density on phenoxide of Alq3 and weaken the intermolecular conjugated interaction between adjacent Alq3 molecules. Hence, the pi--pi* electron transition absorption peak of delta-Alq3 shifts toward short wavelength in UV-Vis absorption spectra, and the maximum emission peak of delta-Alq3 (lamda max = 480 nm) blue-shifts by 35 nm compared with that of alpha-Alq3 (lamda max = 515 nm) in PL spectra. The maximum emission peaks of delta-Alq3 and alpha-Alq3 are all at 520 nm in EL spectra.

Optical band gaps of organic semiconductor materials

NASA Astrophysics Data System (ADS)

Costa, José C. S.; Taveira, Ricardo J. S.; Lima, Carlos F. R. A. C.; Mendes, Adélio; Santos, Luís M. N. B. F.

2016-08-01

UV-Vis can be used as an easy and forthright technique to accurately estimate the band gap energy of organic π-conjugated materials, widely used as thin films/composites in organic and hybrid electronic devices such as OLEDs, OPVs and OFETs. The electronic and optical properties, including HOMO-LUMO energy gaps of π-conjugated systems were evaluated by UV-Vis spectroscopy in CHCl3 solution for a large number of relevant π-conjugated systems: tris-8-hydroxyquinolinatos (Alq3, Gaq3, Inq3, Al(qNO2)3, Al(qCl)3, Al(qBr)3, In(qNO2)3, In(qCl)3 and In(qBr)3); triphenylamine derivatives (DDP, p-TTP, TPB, TPD, TDAB, m-MTDAB, NPB, α-NPD); oligoacenes (naphthalene, anthracene, tetracene and rubrene); oligothiophenes (α-2T, β-2T, α-3T, β-3T, α-4T and α-5T). Additionally, some electronic properties were also explored by quantum chemical calculations. The experimental UV-Vis data are in accordance with the DFT predictions and indicate that the band gap energies of the OSCs dissolved in CHCl3 solution are consistent with the values presented for thin films.

Determination of dissolved aluminum in water samples

USGS Publications Warehouse

Afifi, A.A.

1983-01-01

A technique has been modified for determination of a wide range of concentrations of dissolved aluminum (Al) in water and has been tested. In this technique, aluminum is complexed with 8-hydroxyquinoline at pH 8.3 to minimize interferences, then extracted with methyl isobutyl ketone (MIBK). The extract is analyzed colorimetrically at 395 nm. This technique is used to analyze two forms of monomeric Al, nonlabile (organic complexes) and labile (free, Al, Al sulfate, fluoride and hydroxide complexes). A detection limit 2 ug/L is possible with 25-ml samples and 10-ml extracts. The detection limit can be decreased by increasing the volume of the sample and (or) decreasing the volume of the methyl isobutyl ketone extract. The analytical uncertainty of this method is approximately + or - 5 percent. The standard addition technique provides a recovery test for this technique and ensures precision in samples of low Al concentrations. The average percentage recovery of the added Al plus the amount originally present was 99 percent. Data obtained from analyses of filtered standard solutions indicated that Al is adsorbed on various types of filters. However, the relationship between Al concentrations and adsorption remains linear. A test on standard solutions also indicated that Al is not adsorbed on nitric acid-washed polyethylene and polypropylene bottle wells. (USGS)

Color-tunable mixed photoluminescence emission from Alq3 organic layer in metal-Alq3-metal surface plasmon structure.

PubMed

Chen, Nai-Chuan; Liao, Chung-Chi; Chen, Cheng-Chang; Fan, Wan-Ting; Wu, Jin-Han; Li, Jung-Yu; Chen, Shih-Pu; Huang, Bohr-Ran; Lee, Li-Ling

2014-01-01

This work reports the color-tunable mixed photoluminescence (PL) emission from an Alq3 organic layer in an Au-Alq3-Au plasmonic structure through the combination of organic fluorescence emission and another form of emission that is enabled by the surface plasmons in the plasmonic structure. The emission wavelength of the latter depends on the Alq3 thickness and can be tuned within the Alq3 fluorescent spectra. Therefore, a two-color broadband, color-tunable mixed PL structure was obtained. Obvious changes in the Commission Internationale d'Eclairage (CIE) coordinates and the corresponding emission colors of Au-Alq3-Au samples clearly varied with the Alq3 thickness (90, 130, and 156 nm).

Color-tunable mixed photoluminescence emission from Alq3 organic layer in metal-Alq3-metal surface plasmon structure

PubMed Central

2014-01-01

This work reports the color-tunable mixed photoluminescence (PL) emission from an Alq3 organic layer in an Au-Alq3-Au plasmonic structure through the combination of organic fluorescence emission and another form of emission that is enabled by the surface plasmons in the plasmonic structure. The emission wavelength of the latter depends on the Alq3 thickness and can be tuned within the Alq3 fluorescent spectra. Therefore, a two-color broadband, color-tunable mixed PL structure was obtained. Obvious changes in the Commission Internationale d’Eclairage (CIE) coordinates and the corresponding emission colors of Au-Alq3-Au samples clearly varied with the Alq3 thickness (90, 130, and 156 nm). PMID:25328506

A green emissive amorphous fac-Alq3 solid generated by grinding crystalline blue fac-Alq3 powder.

PubMed

Bi, Hai; Chen, Dong; Li, Di; Yuan, Yang; Xia, Dandan; Zhang, Zuolun; Zhang, Hongyu; Wang, Yue

2011-04-14

A novel green emissive Alq(3) solid with a facial isomeric form has been obtained by grinding the typical blue luminescent fac-Alq(3) crystalline powder. This is the first report, to the best of our knowledge, that a fac-Alq(3) isomer emits green light.

Operational stability of electrophosphorescent devices containing p and n doped transport layers

NASA Astrophysics Data System (ADS)

D'Andrade, Brian W.; Forrest, Stephen R.; Chwang, Anna B.

2003-11-01

The operational stability of low-operating voltage p-i-n electrophosphorescent devices containing fac-tris(2-phenylpyridine) iridium as the emissive dopant is investigated. In these devices, Li-doped 4,7-diphenyl-1,10-phenanthroline (BPhen) served as an n-type electron transport layer, or as an undoped hole blocking layer (HBL), and 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane doped 4,4',4″-tris(3-methylphenylphenylamino) triphenylamine served as a p-type hole transport layer. The glass transition temperature of BPhen can be increased by the addition of aluminum(III)bis(2-methyl-8-quinolinato)4-phenylphenolate (BAlq), resulting in improved morphological stability, thereby reducing device degradation. When thermally stable BAlq was used as a HBL in both p-i-n and undoped devices, the extrapolated operational lifetime (normalized to an initial luminance of 100 cd/m2) of the p-i-n and undoped devices are 18 000 and 60 000 h, respectively, indicating that the presence of p and n dopants can accelerate device degradation.

ON THE RELATIVE STABILITY OF ALUMINUM, TITANIUM, VANADIUM, IRON, AND COPPER TARTRATE COMPLEXES IN ALKALI MEDIA (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pyatnitskii, I.V.; Kostyshina, A.P.

1959-06-01

The stability of aluminum, copper, iron, titunium, and vanadium tartrate complexes was determined using bond magnitudes as criteria (the ratio between the concentrations of complexed and free ions at a certain standard acid condition). A method is suggested for determining the ratio of the bonds combining the complexes of two metals. The partition constaats of aluminum, copper, iron(III), and vanadium hydroxyquinolinates between the aqueous solution and chloroform were 2.6 x 10/sup -33/, 7.3 x 10/sup -23/, 1.5 x 10/sup -37/, and 4.2 x 10/sup -23/, respectively. The relative stability of copper and iron turtrate complexes in alkali solution (pH 13)more » and aluminum, iron(III), titunium, and vanadium(IV) tartrate complexes in ammonium solution (pH 9.5) was determined. (R.V.J.)« less

TiO2 as diffusion barrier at Co/Alq3 interface studied by x-ray standing wave technique

NASA Astrophysics Data System (ADS)

Phatak Londhe, Vaishali; Gupta, A.; Ponpandian, N.; Kumar, D.; Reddy, V. R.

2018-06-01

Nano-scale diffusion at the interfaces in organic spin valve thin films plays a vital role in controlling the performance of magneto-electronic devices. In the present work, it is shown that a thin layer of titanium dioxide at the interface of Co/Alq3 can act as a good diffusion barrier. The buried interfaces of Co/Alq3/Co organic spin valve thin film has been studied using x-ray standing waves technique. A planar waveguide is formed with Alq3 layer forming the cavity and Co layers as the walls of the waveguide. Precise information about diffusion of Co into Alq3 is obtained through excitation of the waveguide modes. It is found that the top Co layer diffuses deep into the Alq3 resulting in incorporation of 3.1% Co in the Alq3 layer. Insertion of a 1.7 nm thick barrier layer of TiO2 at Co/Alq3 interface results in a drastic reduction in the diffusion of Co into Alq3 to a value of only 0.4%. This suggests a better performance of organic spin valve with diffusion barrier of TiO2.

Observation of spin-polarized electron transport in Alq3 by using a low work function metal

NASA Astrophysics Data System (ADS)

Jang, Hyuk-Jae; Pernstich, Kurt P.; Gundlach, David J.; Jurchescu, Oana D.; Richter, Curt. A.

2012-09-01

We present the observation of magnetoresistance in Co/Ca/Alq3/Ca/NiFe spin-valve devices. Thin Ca layers contacting 150 nm thick Alq3 enable the injection of spin-polarized electrons into Alq3 due to the engineering of the band alignment. The devices exhibit symmetric current-voltage (I-V) characteristics indicating identical metal contacts on Alq3, and up to 4% of positive magnetoresistance was observed at 4.5 K. In contrast, simultaneously fabricated Co/Alq3/NiFe devices displayed asymmetric I-V curves due to the different metal electrodes, and spin-valve effects were not observed.

Solid Phase Extraction of Inorganic Mercury Using 5-Phenylazo-8-hydroxyquinoline and Determination by Cold Vapor Atomic Fluorescence Spectroscopy in Natural Water Samples

PubMed Central

Daye, Mirna; Halwani, Jalal; Hamzeh, Mariam

2013-01-01

8-Hydroxyquinoline (8-HQ) was chosen as a powerful ligand for Hg solid phase extraction. Among several chelating resins based on 8-HQ, 5-phenylazo-8-hydroxyquinoline (5Ph8HQ) is used for mercury extraction in which the adsorption dynamics were fully studied. It has been shown that Hg(II) is totally absorbed by 5Ph8HQ within the first 30 minutes of contact time with t 1/2 5 minutes, following Langmuir adsorption model. At pH 4, the affinity of mercury is unchallenged by other metals except, for Cu(II), which have shown higher Kd value. With these latter characteristics, 5Ph8HQ was examined for the preconcentration of trace levels of Hg(II). The developed method showed quantitative recoveries of Hg(II) with LOD = 0.21 pg mL−1 and RSD = 3–6% using cold vapor atomic fluorescence spectroscopy (CV-AFS) with a preconcentration factor greater than 250. PMID:24459417

[White organic light emitting device with dyestuff DCJTB blended in polymer].

PubMed

Zhang, Yan-Fei; Xu, Zheng; Zhang, Fu-Jun; Wang, Yong; Zhao, Su-Ling

2008-04-01

The Alq3 and DCJTB were blended with poly (N-vinylcarbazole) (PVK) in different weight ratios and spin coated into films. Multilayer devices with the light emitting layer PVK : Alq3 : DCJTB were fabricated, and their structure was ITO/ PVK : Alq3 : DCJTB/ BCP/Alq3/LiF/Al in which BCP and Alq3 were employed as the hole-blocking and electron-transporting layers respectively, PVK is the blue light-emitting as well as hole-transporting layer. The mass proportion of PVK relative to Alq3 was tuned while the quality ratio of PVK to DCJTB remained (100 : 1). Finally, fairly pure and stabile white emission was achieved when PVK : Alq3 : DCJTB was 100 : 5 : 1. The CIE coordinate was (0.33, 0.36) at 14 V, which is very stable at various biases (10-14 V).

Vibrational assignment of aluminum(III) Tris-acetylacetone

NASA Astrophysics Data System (ADS)

Tayyari, Sayyed Faramarz; Raissi, Haydar; Ahmadabadi, Zahra

2002-10-01

The geometry, frequency and intensity of the vibrational bands of aluminum(III) Tris-acetylacetone Al(AA) 3 and its 1, 3, 5- 13C derivative were obtained by the Hartree-Fock (HF) and Density Functional Theory (DFT) with the B3LYP, B1LYP, and G96LYP functionals and using the 6-31G* basis set. The calculated frequencies are compared with the solid IR and Raman spectra. All of the measured IR and Raman bands were interpreted in terms of the calculated vibrational modes. Most computed bands are predicted to be at higher wavenumbers than the experimental bands. The calculated bond lengths and bond angles are in good agreement with the experimental results. Analysis of the vibrational spectra indicates a strong coupling between the chelated ring modes. Four bands in the 500-390 cm -1 frequency range are assigned to the vibrations of metalligand bonds.

Tunable electroluminescent color for 2, 5-diphenyl -1, 4-distyrylbenzene with two trans-double bonds

NASA Astrophysics Data System (ADS)

Cheng, Gang; Zhang, Yingfang; Zhao, Yi; Liu, Shiyong; Xie, Zengqi; Xia, Hong; Hanif, Muddasir; Ma, Yuguang

2005-07-01

Exciplex emission is observed in electroluminescent (EL) spectrum of an organic light-emitting device (OLED), where 2, 5-diphenyl -1, 4-distyrylbenzene with two trans-double bonds (trans-DPDSB), (8-hydroxyquinoline) aluminum, and N,N'-diphenyl-N,N'-bis(1-naphthyl)-(1,1'-biphenyl)-4,4'-diamine (NPB) are used as light-emitting, electron-transporting, and hole-transporting layers, respectively. This emission can be dramatically weakened by inserting a hole-injecting layer of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid) between the hole-transporting layer and the anode. Consequently, EL color of this OLED is tuned from white to blue. This phenomenon may result from the improvement of hole injection, which shifts the major recombination zone from the NPB/trans-DPDSB interface to the trans-DPDSB layer.

Doubly Vinylogous Aldol Reaction of Furoate Esters with Aldehydes and Ketones.

PubMed

Hartwig, William T; Sammakia, Tarek

2017-01-06

The use of bulky Lewis acids, aluminum tris(2,6-diphenylphenoxide) (ATPH) and aluminum tris(2,6-di-2-naphthylphenoxide) (ATNP), in the doubly vinylogous aldol reaction between methyl-5-methyl-2-furoate and aldehydes or ketones is described. These reactions proceed smoothly and in high yields with both enolizable and non-enolizable substrates. This C-C bond-forming reaction enables a new bond construction for the synthesis of functionalized furans.

Emission and Dynamics of Charge Carriers in Uncoated and Organic/Metal Coated Semiconductor Nanowires

NASA Astrophysics Data System (ADS)

Kaveh Baghbadorani, Masoud

In this dissertation, the dynamics of excitons in hybrid metal/organic/nanowire structures possessing nanometer thick deposited molecular and metal films on top of InP and GaAs nanowire (NW) surfaces were investigated. Optical characterizations were carried out as a function of the semiconductor NW material, design, NW size and the type and thickness of the organic material and metal used. Hybrid organic and plasmonic semiconductor nanowire heterostructures were fabricated using organic molecular beam deposition technique. I investigated the photon emission of excitons in 150 nm diameter polytype wurtzite/zincblende InP NWs and the influence of a few ten nanometer thick organic and metal films on the emission using intensity- and temperature-dependent time-integrated and time resolved (TR) photoluminescence (PL). The plasmonic NWs were coated with an Aluminum quinoline (Alq3) interlayer and magnesium-silver (Mg0.9:Ag0.1) top layer. In addition, the nonlinear optical technique of heterodyne four-wave mixing was used (in collaboration with Prof. Wolfgang Langbein, University of Cardiff) to study incoherent and coherent carrier relaxation processes on bare nanowires on a 100 femtosecond time-scale. Alq3 covered NWs reveal a stronger emission and a longer decay time of exciton transitions indicating surface state passivation at the Alq3/NW interface. Alq3/Mg:Ag NWs reveal a strong quenching of the exciton emission which is predominantly attributed to Forster energy-transfer from excitons to plasmon oscillations in the metal cluster film. Changing the Mg:Ag to gold and the organic Alq3 spacer layer to PTCDA leads to a similar behavior, but the PL quenching is strongly increased. The observed behavior is attributed to a more continuous gold deposition leading to an increased Forster energy transfer and to a metal induced band-bending. I also investigated ensembles of bare and gold/Alq3 coated GaAs-AlGaAs-GaAs core shell NWs of 130 nm diameter. Plasmonic NWs with Au coating reveal a significant reduction of the PL intensity compared with the uncoated NWs. Organic-plasmonic NWs with an additional Alq3 interlayer show a noticeably stronger PL intensity which increases with rising Alq3 spacer thickness. Metal induced band bending is mainly attributed to be responsible for the PL quenching. TR PL measurements support our interpretation by showing an increase in the exciton decay times as we increase the spacer thickness. Au coated NWs also reveal a strong polarization dependent absorption which is mainly due to the significant dielectric mismatch between the nanowires and the adjacent vacuum environment. Finally, the amplified spontaneous emission (ASE) and possible plasmonic NW lasing from hybrid plasmonic core-shell GaAs NW heterostructures was investigated. The plasmonic heterostructures are composed of either bare NWs on an Au coated glass substrate or Au coated NWs on a bare glass substrate. Intensity-dependent PL on plasmonic NW samples reveals a super linear increase of the PL intensities which is attributed to an ASE at a threshold energy fluence of 1 GW/cm 2. Measurements above the threshold power reveal few weakly resolved broad bands around the maximum emission of the PL band which suggest plasmonic film induced lasing. This interpretation is supported by the fact that lasing from such 100 nm narrow uncoated GaAs NWs is not possible.

Electroluminescence dependence on the organic thickness in ZnO nano rods/Alq3 heterostructure devices.

PubMed

Kan, Pengzhi; Wang, Yongsheng; Zhao, Suling; Xu, Zheng; Wang, Dawei

2011-04-01

ZnO nanorods are synthesised by a hydrothermal method on ITO glass. Their crystallization and morphology are detected by XRD and SEM, respectively. The results show that the ZnO nanorod array has grown primarily along a direction aligned perpendicular to the ITO substrate. The average height and diameter of the nanorods is about 130 nm and 30 nm, respectively. Then ZnO nano rods/Alq3 heterostructure LEDs are prepared by thermal evaporation of Alq3 molecules. The thicknesses of the Alq3 layers are 130 nm, 150 nm, 170 nm and 190 nm, respectively. The electroluminescence of the devices is detected under different DC bias voltages. The exciton emission of Alq3 is detected in all devices. When the thickness of Alq3 is 130 nm, the UV electroluminescence of ZnO is around 382 nm, and defect emissions around 670 nm and 740 nm are detected. Defect emissions of ZnO nanorods are prominent. When the thickness of Alq3 increases to over 170 nm, it is difficult to observe defect emissions from the ZnO nano rods. In such devices, the exciton emission of Alq3 is more prominent than other emissions under different bias voltage.

Hybrid Structure White Organic Light Emitting Diode for Enhanced Efficiency by Varied Doping Rate.

PubMed

Kim, Dong-Eun; Kang, Min-Jae; Park, Gwang-Ryeol; Kim, Nam-Kyu; Lee, Burm-Jong; Kwon, Young-Soo; Shin, Hoon-Kyu

2016-03-01

Novel materials based on Zn(HPB)2 and Ir-complexes were synthesized as blue or red emitters, respectively. White organic light emitting diodes were fabricated using the Zn(HPB)2 as a blue emitting layer, Ir-complexes as a red emitting layer and Alq3 as a green emitting layer. The obtained experimental results, were based on white OLEDs fabricated using double emission layers of Zn(HPB)2 and Alq3:Ir-complexes. The doping rate of the Ir-complexes was varied at 0.4%, 0.6%, 0.8% and 1.0%. When the doping rate of the Alq3:Ir-complexes was 0.6%, a white emission was achieved. The Commission Internationale de l'Eclairage coordinates of the device's white emission were (0.316, 0.331) at an applied voltage of 10.75 V.

Effect of inserting a hole injection layer in organic light-emitting diodes: A numerical approach

NASA Astrophysics Data System (ADS)

Lee, Hyeongi; Hwang, Youngwook; Won, Taeyoung

2015-01-01

For investigating the effect of inserting a hole injection layer (HIL), we carried out a computational study concerning organic light-emitting diodes (OLEDs) that had a thin CuPc layer as the hole injection layer. We used S-TAD (2, 2', 7, 7'-tetrakis-(N, Ndiphenylamino)-9, 9-spirobifluoren) for the hole transfer layer, S-DPVBi (4, 4'-bis (2, 2'-diphenylvinyl)-1, 1'-spirobiphenyl) for the emission layer and Alq3 (Tris (8-hyroxyquinolinato) aluminium) for the electron transfer layer. This tri-layer device was compared with four-layer devices. To this tri-layer device, we added a thin CuPc layer, which had a 5.3 eV highest occupied molecular orbital (HOMO) level and a 3.8 eV lowest unoccupied molecular orbital (LUMO) level, as a hole injection layer, and we chose this device for Device A. Also, we varied the LUMO level or the HOMO level of the thin CuPc layer. These two devices were identified as Device C and Device D, respectively. In this paper, we simulated the carrier injection, transport and recombination in these four devices. Thereby, we showed the effect of the HIL, and we demonstrated that the characteristics of these devices were improved by adding a thin layer of CuPc between the anode and the HTL.

Analysis of the Electrical Properties of an Electron Injection Layer in Alq3-Based Organic Light Emitting Diodes.

PubMed

Kim, Soonkon; Choi, Pyungho; Kim, Sangsub; Park, Hyoungsun; Baek, Dohyun; Kim, Sangsoo; Choi, Byoungdeog

2016-05-01

We investigated the carrier transfer and luminescence characteristics of organic light emitting diodes (OLEDs) with structure ITO/HAT-CN/NPB/Alq3/Al, ITO/HAT-CN/NPB/Alq3/Liq/Al, and ITO/HAT-CN/NPB/Alq3/LiF/A. The performance of the OLED device is improved by inserting an electron injection layer (EIL), which induces lowering of the electron injection barrier. We also investigated the electrical transport behaviors of p-Si/Alq3/Al, p-Si/Alq3/Liq/Al, and p-Si/Alq3/LiF/Al Schottky diodes, by using current-voltage (L-V) and capacitance-voltage (C-V) characterization methods. The parameters of diode quality factor n and barrier height φ(b) were dependent on the interlayer materials between Alq3 and Al. The barrier heights φ(b) were 0.59, 0.49, and 0.45 eV, respectively, and the diode quality factors n were 1.34, 1.31, and 1.30, respectively, obtained from the I-V characteristics. The built in potentials V(bi) were 0.41, 0.42, and 0.42 eV, respectively, obtained from the C-V characteristics. In this experiment, Liq and LiF thin film layers improved the carrier transport behaviors by increasing electron injection from Al to Alq3, and the LiF schottky diode showed better I-V performance than the Liq schottky diode. We confirmed that a Liq or LiF thin film inter-layer governs electron and hole transport at the Al/Alq3 interface, and has an important role in determining the electrical properties of OLED devices.

A Novel trans-1-(9-Anthryl)-2-phenylethene Derivative Containing a Phenanthroimidazole Unit for Application in Organic Light-Emitting Diodes.

PubMed

Zhou, Nonglin; Wang, Shirong; Xiao, Yin; Li, Xianggao

2018-01-04

Aryl-substituted phenanthroimidazoles (PIs) have attracted tremendous attention in the field of organic light-emitting diodes (OLEDs), because they are simple to synthesize and have excellent thermal properties, high photoluminescence quantum yields (PLQYs), and bipolar properties. Herein, a novel blue-green emitting material, (E)-2-{4'-[2-(anthracen-9-yl)vinyl]-[1,1'-biphenyl]-4-yl}-1-phenyl-1H-phenanthro[9,10-d]imidazole (APE-PPI), containing a t-APE [1-(9-anthryl)-2-phenylethene] core and a PI moiety was designed and synthesized. Owing to the PI skeleton, APE-PPI possesses high thermal stability and a high PLQY, and the compound exhibits bipolar transporting characteristics, which were identified by single-carrier devices. Nondoped blue-green OLEDs with APE-PPI as the emitting layer show emission at λ=508 nm, a full width at half maximum of 82 nm, a maximum brightness of 9042 cd m -2 , a maximum current efficiency of 2.14 cd A -1 , and Commission Internationale de L'Eclairage (CIE) coordinates of (0.26, 0.55). Furthermore, a white OLED (WOLED) was fabricated by employing APE-PPI as the blue-green emitting layer and 4-(dicyanomethylene)-2-tert-butyl-6-(1,1,7,7-tetramethyljulolidin-4-yl-vinyl)-4H-pyran (DCJTB) doped in tris-(8-hydroxyquinolinato)aluminum (Alq 3 ) as the red-green emitting layer. This WOLED exhibited a maximum brightness of 10029 cd m -2 , a maximum current efficiency of 16.05 cd A -1 , CIE coordinates of (0.47, 0.47), and a color rendering index (CRI) of 85. The high performance of APE-PPI-based devices suggests that the t-APE and PI combination can potentially be used to synthesize efficient electroluminescent materials for WOLEDs. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis and characterization of Au incorporated Alq3 nanowires

NASA Astrophysics Data System (ADS)

Khan, Mohammad Bilal; Ahmad, Sultan; Parwaz, M.; Rahul, Khan, Zishan H.

2018-05-01

We report the synthesis and characterization of pure and Au incorporated Alq3 nanowires. These nanowires are synthesized using thermal vapor transport method. The luminescence intensity of Au incorporated Alq3 nanowires are recorded to be higher than that of pure Alq3 nanowires, which is found to increase with the increase in Au concentration. Fluorescence quenching is also observed when Au concentration is increased beyond the certain limit.

Hyperfine interaction and its effects on spin dynamics in organic solids

NASA Astrophysics Data System (ADS)

Yu, Z. G.; Ding, Feizhi; Wang, Haobin

2013-05-01

Hyperfine interaction (HFI) and spin-orbit coupling are two major sources that affect electron spin dynamics. Here we present a systematic study of the HFI and its role in organic spintronic applications. For electron spin dynamics in disordered π-conjugated organics, the HFI can be characterized by an effective magnetic field whose modular square is a weighted sum of contact and dipolar contributions. We determine the effective HFI fields of some common π-conjugated organics studied in the literature via first-principles calculations. Most of them are found to be less than 2 mT. While the H atoms are the major source of the HFI in organics containing only the C and H atoms, many organics contain other nuclear spins, such as Al and N in tris-(8-hydroxyquinoline) aluminum, that contribute to the total HFI. Consequently, the deuteration effect on the HFI in the latter may be much weaker than in the former. The HFI gives rise to multiple resonance peaks in electron spin resonance. In disordered organic solids, these individual resonances are unresolved, leading to a broad peak whose width is proportional to the effective HFI field. As electrons hop among adjacent organic molecules, they experience a randomly varying local HFI field, inducing electron spin relaxation and diffusion. This is analyzed rigorously based on master equations. Electron spin relaxation undergoes a crossover along the ratio between the electron hopping rate η¯ and the Larmor frequency Ω of the HFI field. The spin relaxation rate increases (decreases) with η¯ when η¯≪Ω (η¯≫Ω). A coherent beating of electron spin at Ω is possible when the external field is small compared to the HFI. In this regime, the magnetic field is found to enhance the spin relaxation.

X-rays sensing properties of MEH-PPV, Alq₃ and additive components: a new organic dosimeter as a candidate for minimizing the risk of accidents of patients undergoing radiation oncology.

PubMed

Schimitberger, T; Ferreira, G R; Akcelrud, L C; Saraiva, M F; Bianchi, R F

2013-01-01

In this paper, we report our experimental design in searching a smart and easy-to-read dosimeter used to detect 6 MV X-rays for improving patient safety in radiation oncology. The device was based on an organic emissive solutions of poly(2-methoxy-5(2'-ethylhexyloxy)-p-phenylenevinylene) (MEH-PPV), aluminum-tris-(8-hydroxyquinoline) (Alq₃) and additive components which were characterized by UV-Vis absorption, photoluminescence and CIE color coordinate diagram. The optical properties of MEH-PPV/Alq₃ solutions have been examined as function of radiation dose over the range of 0-100 Gy. It has shown that MEH-PPV/Alq₃ solutions are specifically sensitive to X-rays, since the effect of radiation on this organic system is strongly correlated with the efficient spectral overlap between Alq₃ emission and the absorption of degraded MEH-PPV, which alters the color and photoemission of MEH-PPV/Alq₃ mixtures from red to yellow, and then to green. The rate of this change is more sensitive when MEH-PPV/Alq₃ is irradiated in the presence of benzoyl peroxide than when in the presence of hindered phenolic stabilizers, respectively, an accelerator and an inhibitor to activate or inhibit free radical formation. This gives rise to optimize the response curve of the dosimeter. It is clear from the experimental results that organic emissive semiconductors have potential to be used as dedicated and low-cost dosimeters to provide an independent check of beam output of a linear accelerator and therefore to give patients the opportunity to have information on the dose prescription or equipment-related problems a few minutes before being exposed to radiation. Copyright © 2012 IPEM. Published by Elsevier Ltd. All rights reserved.

Infrared and Raman spectroscopic studies of tris-[3-(trimethoxysilyl)propyl] isocyanurate, its sol-gel process, and coating on aluminum and copper.

PubMed

Li, Ying-Sing; Church, Jeffrey S; Woodhead, Andrea L; Vecchio, Nicolas E; Yang, Johnny

2014-11-11

Tris-[3-(trimethoxysilyl)propyl] isocyanurate (TTPI) has been used as a precursor to prepare a sol using ethanol as the solvent under acidic conditions. The sol-gel was applied for the surface treatment of aluminum and copper. Infrared and Raman spectra have been recorded for pure TTPI and the TTPI sol, xerogel and TTPI sol-gel coated metals. From the vibrational spectra, TTPI is likely to have the C1 point group. Vibrational assignments are suggested based on group frequencies, the expected reactions in the sol-gel process and the vibrational studies of some related molecules. From the experimental infrared spectra of xerogels annealed at different temperatures and from the thermal-gravimetric analysis, it is found that the TTPI xerogel decomposes at around 450°C with silica being the major decomposition product. A cyclic voltammetric study of the metal electrodes coated with different concentrations of TTPI ranging from 5% to 42% (v/v) has shown that the films with high concentrations of sol would provide better corrosion protection for aluminum and copper. Copyright © 2014 Elsevier B.V. All rights reserved.

[Performance dependence of organic light-emitting devices on the thickness of Alq3 emitting layer].

PubMed

Lian, Jia-rong; Liao, Qiao-sheng; Yang, Rui-bo; Zheng, Wei; Zeng, Peng-ju

2010-10-01

The dependence of opto-electronical characteristics in organic light-emitting devices on the thickness of Alq3 emitter layer was studied, where MoO3, NPB, and Alq3 were used as hole injector, hole transporter, and emitter/electron transporter, respectively. By increasing the thickness of Alq3 layer from 20 to 100 nm, the device current decreased gradually, and the EL spectra of devices performed a little red shift with an obvious broadening in long wavelength range but a little decrease in intensity of short wavelength range. The authors simulated the EL spectra using the photoluminescence (PL) spectra of Alq3 as Alq3 intrinsic emission, which coincided with the experimental EL spectra well. The simulated results suggested that the effect of interference takes the major role in broadening the long wavelength range of EL spectra, and the distribution of emission zone largely affects the profile of EL spectra in short wavelength range.

Electrical and Luminescent Properties of Color-Changeable Organic Electroluminescent Diode Using Squarylium Dyes

NASA Astrophysics Data System (ADS)

Mori, Tatsuo; Miyachi, Kiyokazu; Kichimi, Tomoaki; Mizutani, Teruyoshi

1994-12-01

The organic electoluminescent diode (LED) with squarylium (Sq) dye-doped Alq3 changes color upon application of voltage (current). The luminescent color from the organic LED changes from red (electroluminescence (EL) of Sq dye) at low voltage to light green (EL of Alq3) at high voltage. We studied the EL efficiency and EL spectrum of organic Sq-doped Alq3 LED with various doping positions in the emission layer. Consequentially, it was clarified that Sq doping near TPD considerably reduced the EL efficiency. The EL mechanism of the organic LED was concluded to be associated with the energy transfer from the excited Alq3 to the guest dye and hole trapping of the guest dye in Alq3.

Exchange-Dominated Pure Spin Current Transport in Alq3 Molecules.

PubMed

Jiang, S W; Liu, S; Wang, P; Luan, Z Z; Tao, X D; Ding, H F; Wu, D

2015-08-21

We address the controversy over the spin transport mechanism in Alq3 utilizing spin pumping in the Y3Fe5O12/Alq3/Pd system. An unusual angular dependence of the inverse spin Hall effect is found. It, however, disappears when the microwave magnetic field is fully in the sample plane, excluding the presence of the Hanle effect. Together with the quantitative temperature-dependent measurements, these results provide compelling evidence that the pure spin current transport in Alq3 is dominated by the exchange-mediated mechanism.

Structure and electronic properties of Alq3 derivatives with electron acceptor/donor groups at the C4 positions of the quinolate ligands: a theoretical study.

PubMed

Rao, Joshi Laxmikanth; Bhanuprakash, Kotamarthi

2011-12-01

The molecular structures of the ground (S(0)) and first singlet excited (S(1)) states of Alq3 derivatives in which pyrazolyl and 3-methylpyrazolyl groups are substituted at the C4 positions of the 8-hydroxyquinolate ligands as electron acceptors, and piperidinyl and N-methylpiperazinyl groups are substituted at the same positions as electron donors, have been optimized using the B3LYP/6-31G and CIS/6-31G methods, respectively. In order to analyze the electronic transitions in these derivatives, the frontier molecular orbital characteristics were analyzed systematically, and it was found that the highest occupied molecular orbital is localized on the A ligand while the lowest unoccupied molecular orbital is localized on the B ligand in their ground states, similar to what is seen for mer-Alq3. The absorption and emission spectra were evaluated at the TD-PBE0/6-31G level, and it was observed that electron acceptor substitution causes a red-shift in the emission spectra, which is also seen experimentally. The reorganization energies were calculated at the B3LYP/6-31G level and the results show that acceptor/donor substitution has a significant effect on the intrinsic charge mobilities of these derivatives as compared to mer-Alq3.

Optochemical sensor based on screenprinted fluorescent sensorspots surrounded by organic photodiodes for multianalyte detection

NASA Astrophysics Data System (ADS)

Kraker, E.; Lamprecht, B.; Haase, A.; Jakopic, G.; Abel, T.; Konrad, C.; Köstler, S.; Tscherner, M.; Stadlober, B.; Mayr, T.

2010-08-01

A compact, integrated photoluminescence based oxygen sensor, utilizing an organic light emitting device (OLED) as the light source and an organic photodiode (OPD) as the detection unit, is described. The detection system of the sensor array consists of an array of circular screen-printed fluorescent sensor spots surrounded by organic photodiodes as integrated fluorescence detectors. The OPD originates from the well-known Tang photodiode, consisting of a stacked layer of copper phthalocyanine (CuPc, p-type material) and perylene tetracarboxylic bisbenzimidazole (PTCBi, n-type material). An additional layer of tris-8-hydroxyquinolinatoaluminium (Alq3, n-type material) was inserted between the PTCBi layer and cathode. An ORMOCERR layer was used as encapsulation layer. For excitation an organic light emitting diode is used. The sensor spot and the detector are processed on the same flexible substrate. This approach not only simplifies the detection system by minimizing the numbers of required optical components - no optical filters have to be used for separating the excitation light and the luminescent emission-, but also has a large potential for low-cost sensor applications. The feasibility of the concept is demonstrated by an integrated oxygen sensor, indicating good performance. Sensor schemes for other chemical parameters are proposed.

Enhanced photoluminescence of Alq3 via patterned array silver dendritic nanostructures

NASA Astrophysics Data System (ADS)

Hsu, Wei-Hsiu; Hsieh, Ming-Hao; Lo, Shih-Shou

2012-04-01

Various silver nanostructures, semi-ball, jungle, and dendritic, are demonstrated by an electrical deposition process. The formation of silver nanostructures with various morphologies is studied by the mechanism of the diffusion limited aggregation (DLA) model. A array pattern of silver nanostructures can be obtained when the conductive substrate was used in a uniform electrical filed. A thickness 500 nm of Alq3 thin-film was covered on the silver nanostructure by thermal evaporation method. The strongest intensity of Alq3 green emission was observed when the pattern-array dendritic silver nanostructure was covered by Alq3. It can be explained with the plasmonic coupling due to the Alq3 and dendritic nanostructure. The result can help us to further application the patterned-array silver dendritic nanostructure for advanced opto-electronic device.

Authentic leadership in a health sciences university.

PubMed

Al-Moamary, Mohamed S; Al-Kadri, Hanan M; Tamim, Hani M

2016-01-01

To study authentic leadership characteristics between academic leaders in a health sciences university. Cross-sectional study at a health sciences university in Saudi Arabia. The Authentic Leadership Questionnaire (ALQ) was utilized to assess authentic leadership. Out of 84 ALQs that were distributed, 75 (89.3%) were eligible. The ALQ scores showed consistency in the dimensions of self-awareness (3.45 ± 0.43), internalized moral prospective (3.46 ± 0.33) and balanced processing (3.42 ± 0.36). The relational transparency dimension had a mean of 3.24 ± 0.31 which was significantly lower than other domains. Academic leaders with medical background represented 57.3%, compared to 42.7% from other professions. Academic leaders from other professions had better ALQ scores that reached statistical significance in the internalized moral perspective and relational transparency dimensions with p values of 0.006 and 0.049, respectively. In reference to the impact of hierarchy, there were no significant differences in relation to ALQ scores. Almost one-third of academic leaders (34.7%) had Qualifications in medical education that did not show significant impact on ALQ scores. There was less-relational transparency among academic leaders that was not consistent with other ALQ domains. Being of medical background may enhance leaders' opportunity to be at a higher hierarchy status but it did not enhance their ALQ scores when compared to those from other professions. Moreover, holding a master in medical education did not impact leadership authenticity.

A stable Alq3@MOF composite for white-light emission.

PubMed

Xie, Wei; He, Wen-Wen; Du, Dong-Ying; Li, Shun-Li; Qin, Jun-Sheng; Su, Zhong-Min; Sun, Chun-Yi; Lan, Ya-Qian

2016-02-25

A stable mesoporous blue-emitting MOF NENU-521 was successfully constructed. NENU-521 can serve as a host for encapsulating Alq3 to obtain tunable and efficient white-light emission. The Alq3@NENU-521 composite possesses excellent stability and can be used as a promising white phosphor in WLEDs.

Theoretical study on magnetism induced by H vacancy in isolated Alq3 and Gaq3 molecules

NASA Astrophysics Data System (ADS)

Ju, Lin; Xu, Tongshuai; Zhang, Yongjia; Sun, Li

2017-10-01

The magnetism induced by H vacancy in isolated Alq3 and Gaq3 molecules has been studied based on density functional theory. The isolated stoichiometric Alq3 and Gaq3 molecules are non-magnetic. With an H vacancy, both Alq3 and Gaq3 molecules could show magnetism, which are mainly due to the polarization of the C 2p electrons and the magnetic moments are mainly distributed at most nearby C atoms of H vacancies. This is because the unpaired electron on the C atom appears, when the H atom nearby is removed. Six cases of the H vacancy introduced in the Alq3 and Gaq3 molecules are considered, respectively. By comparing the relative defect formation energy, the V H3 vacancy is most likely to appear in the two kinds of molecules. In addition, for the ground state configuration of isolated Alq3 and Gaq3 molecules with two H vacancies, the energy of the ferromagnetic state is lower than that of the antiferromagnetic state, which means that the ferromagnetic state is stable. The ferromagnetic mechanism can be explained by the Heisenberg direct exchange interaction between two the polarized C atoms. Our work opens a new way to synthesize organic magnetic materials and perfects the theory of organic ferromagnetism by introducing the d 0 ferromagnetism.

Novel acid mono azo dye compound: Synthesis, characterization, vibrational, optical and theoretical investigations of 2-[(E)-(8-hydroxyquinolin-5-yl)-diazenyl]-4,5-dimethoxybenzoic acid

NASA Astrophysics Data System (ADS)

Saçmacı, Mustafa; Çavuş, Hatice Kanbur; Arı, Hatice; Şahingöz, Recep; Özpozan, Talat

2012-11-01

Novel acid mono azo dye, 2-[(E)-(8-hydroxyquinolin-5yl)-diazenyl]-4,5-dimethoxybenzoic acid (HQD), was synthesized by coupling diazonium salt solution of 2-amino-4,5-dimethoxybenzoic acid (DMA) with 8-hydroxyquinoline (HQ). This dye was characterized by UV-vis, IR & Raman, 1H and 13C NMR spectroscopic techniques and elemental analysis. The normal coordinate analysis of HQD was also performed to assign each band in vibrational spectra. DFT (B3LYP and B3PW91) calculations were employed to optimize the geometry, to interpret NMR spectra, to calculate and to determine the stable tautomeric structure of the compound. Natural Bond Orbital (NBO) analysis was performed to investigate intramolecular interactions. The vibrational spectral data obtained from solid phase IR & Raman spectra were assigned based on the results of the theoretical calculations. UV-vis spectroscopic technique was employed to obtain the optical band gap of HQD. The analysis of the optical absorption data revealed the existence of direct and indirect transitions in the optical band gaps. The optical band gaps of HQD have been found 1.95 and 1.90 eV for direct and indirect transitions, respectively.

An Introduction to Multivariate Curve Resolution-Alternating Least Squares: Spectrophotometric Study of the Acid-Base Equilibria of 8-Hydroxyquinoline-5-Sulfonic Acid

ERIC Educational Resources Information Center

Rodriguez-Rodriguez, Cristina; Amigo, Jose Manuel; Coello, Jordi; Maspoch, Santiago

2007-01-01

A spectrophotometric study of the acid-base equilibria of 8-hydroxyquinoline-5-sulfonic acid to describe the multivariate curve resolution-alternating least squares algorithm (MCR-ALS) is described. The algorithm provides a lot of information and hence is of great importance for the chemometrics research.

Equilibrium Speciation of Select Lanthanides in the Presence of Acidic Ligands in Homo- and Heterogeneous Solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, Troy A

2011-08-01

This dissertation explores lanthanide speciation in liquid solution systems related to separation schemes involving the acidic ligands: bis(2-ethylhexyl) phosphoric acid (HDEHP), lactate, and 8-hydroxyquinoline. Equilibrium speciation of neodymium (Nd 3+), sodium (Na+), HDEHP, water, and lactate in the TALSPEAK liquid-liquid extraction system was explored under varied Nd 3+ loading of HDEHP in the organic phase and through extraction from aqueous HCl and lactate media. System speciation was probed through vapor pressure osmometry, visible and Fourier Transform Infrared (FTIR) spectroscopy, 22Na and 13C labeled lactate radiotracer distribution measurements, Karl Fischer titrations, and equilibrium pH measurements. Distribution of Nd 3+, Na +,more » lactate, and equilibrium pH were modeled using the SXLSQI software to obtain logKNd and logKNa extraction constants under selected conditions. Results showed that high Nd 3+ loading of the HDEHP led to Nd 3+ speciation that departs from the ion exchange mechanism and includes formation of highly aggregated, polynuclear [NdLactate(DEHP) 2] x; (with x > 1). By substituting lanthanum (La 3+) for Nd 3+ in this system, NMR scoping experiments using 23Na, 31P nuclei and 13C labeled lactate were performed. Results indicated that this technique is sensitive to changes in system speciation, and that further experiments are warranted. In a homogeneous system representing the TALSPEAK aqueous phase, Lactate protonation behavior at various temperatures was characterized using a combination of potentiometric titration and modeling with the Hyperquad computer program. The temperature dependent deprotonation behavior of lactate showed little change with temperature at 2.0 M NaCl ionic strength. Cloud point extraction is a non-traditional separation technique that starts with a homogeneous phase that becomes heterogeneous by the micellization of surfactants through the increase of temperature. To better understand the behavior of europium (Eu 3+) and 8-hydroxyquinoline under cloud point extraction conditions, potentiometric and spectrophotometric titrations coupled with modeling with Hyperquad and SQUAD computer programs were performed to assess europium (Eu 3+) and 8-hydroxyquinoline speciation. Experiments in both water and a 1wt% Triton X-114/water mixed solvent were compared to understand the effect of Triton X-114 on the system speciation. Results indicated that increased solvation of 8-hydroxyquinoline by the mixed solvent lead to more stable complexes involving 8-hydroxyquinoline than in water, whereas competition between hydroxide and Triton X-114 for Eu 3+ led to lower stability hydrolysis complexes in the mixed solvent than in water. Lanthanide speciation is challenging due to the trivalent oxidation state that leads to multiple ligand complexes, including some mixed complexes. The complexity of the system demands well-designed and precise experiments that capture the nuances of the chemistry. This work increased the understanding of lanthanide speciation in the explored systems, but more work is required to produce a comprehensive understanding of the speciation involved.« less

[Photovoltaic character of organic EL devices MEH-PPV/Alq3].

PubMed

Lin, Peng; Liang, Chun-Jun; Deng, Zhen-Bo; Xiong, De-Ping; Wang, Li; Zhang, Zhi-Feng; Zhang, Xi-Qing

2005-01-01

An organic photovoltaic(PV) cell, ITO/MEH-PPV/Alq3/LiF/Al, was fabricated. The MEH-PPV and Alq3 are the electron-acceptor and donor in the cell, respectively. The respond region matchs the adsorption of Alq3 film. Under UV light with 0.5 mW x cm(-2), the cell shows a short-circuit current of 2.4 microA x cm(-2), open-circuit voltage of 2.6 V, a fill factor of 0.71, and a power conversion efficiency of 0.9%. It was found that the PV cell indicates electroluminescence (EL) performance and could emit orange light at DC voltage. The maximum luminance is about 1 000 cd x cm(-2) at 15 V.

Extraction of Pm(III) and Gd(III) by 8-hydroxyquinoline and some related amines in chloroform from nitrate medium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shehata, F.A.; Khalifa, S.M.; El-Dessouky, S.I.

1993-10-01

The extraction of the trivalent radioactive lanthanides (Ln), Pm and Gd from nitrate aqueous medium by 8-hydroxyquinoline (HOX) and/or trilaurylamine (TLA), trioctylamine (TOA), tributylamine (TBA), tripropylamine (TPA) or triallylamine (TAA),L, in chloroform was investigated. The chemical formulae of the extracted organic phase species for both lanthanides were found Ln.NO{sub 3}.(OX){sub 2} for the chelate and Ln.NO{sub 3}(OX){sub 2}.L for the adduct. The respective extraction and formation constants were evaluated. The synergic extraction of Pm and Gd by HOX-amine was investigated as a function of temperature. The thermodynamic parameters, free energy change, enthalpy change and entropy change were evaluated. The stoichiometrymore » of the extracted organic phase species was established and the different data obtained were discussed. 15 refs., 8 figs., 2 tabs.« less

Nonlinear optical study of 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride and 1-(carboxymethyl)quinolin-1-ium chloride salts by Z-scan technique

NASA Astrophysics Data System (ADS)

Zidan, M. D.; Arfan, A.; Allahham, A.

2016-12-01

Z-scan technique was used to investigate the nonlinear optical properties of 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride and 1-(carboxymethyl)quinolin-1-ium chloride salts. The new 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride and 1-(carboxymethyl)quinolin-1-ium chloride salts were synthesized and characterized using UV-visible, FTIR and NMR measurements and the characterization spectra confirm the expected molecular structure of the prepared salts. Measurements were performed with a CW Diode laser at 635 nm wavelength and 26 mW power. The nonlinear optical absorption coefficient (β) and nonlinear refractive index (n2) of the 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride was affected by OH group. The excited-state absorption cross sections (σex) and the ground -state absorption cross sections (σg) were calculated for the two studied compounds. It was found that the σex is larger than the σg, indicating that the reverse saturable absorption mechanism (RSA) is the dominating mechanism for the observed absorption nonlinearities. Our results suggest that this material should be considered as a promising candidate for future optical devices applications.

Effect of SiO 2/Si 3N 4 dielectric distributed Bragg reflectors (DDBRs) for Alq 3/NPB thin-film resonant cavity organic light emitting diodes

NASA Astrophysics Data System (ADS)

Lei, Po-Hsun; Wang, Shun-Hsi; Juang, Fuh Shyang; Tseng, Yung-Hsin; Chung, Meng-Jung

2010-05-01

In this article, we report on the effect of SiO 2/Si 3N 4 dielectric distributed Bragg reflectors (DDBRs) for Alq 3/NPB thin-film resonant cavity organic light emitting diode (RCOLED) in increasing the light output intensity and reducing the linewidth of spontaneous emission spectrum. The optimum DDBR number is found as 3 pairs. The device performance will be bad by further increasing or decreasing the number of DDBR. As compared to the conventional Alq 3/NPB thin-film organic light emitting diode (OLED), the Alq 3/NPB thin-film RCOLED with 3-pair DDBRs has the superior electrical and optical characteristics including a forward voltage of 6 V, a current efficiency of 3.4 cd/A, a luminance of 2715 cd/m 2 under the injection current density of 1000 A/m 2, and a full width at half maximum (FWHM) of 12 nm for emission spectrum over the 5-9 V bias range. These results represent that the Alq 3/NPB thin-film OLED with DDBRs shows a potential as the light source for plastic optical fiber (POF) communication system.

Synchrotron-based soft X-ray spectroscopic studies of the electronic structure of organic semiconducting molecules

NASA Astrophysics Data System (ADS)

Demasi, Alexander

Organic molecules have been the subject of many scientific studies due to their potential for use in a new generation of optoelectronic and semiconducting devices, such as organic photovoltaics and organic light emitting diodes. These studies are motivated by the fact that organic semiconductor devices have several advantages over traditional inorganic semiconductor devices. Unlike inorganic semiconductors, where the electronic properties are a result of the deliberate introduction of dopants to the material, the properties of organic semiconductors are often intrinsic to the molecules themselves. As a result, organic semiconductor devices are frequently less susceptible to contamination by impurities than their inorganic counterparts, which results in the relatively lower cost of producing such devices. Accurate experimental determination of the bulk and surface electronic structure of organic semiconductors is a prerequisite in developing a comprehensive understanding of such materials. The organic materials studied in this thesis were N,N-Ethylene-bis(1,1,1trifluoropentane-2,4-dioneiminato)-copper(ii) (abbreviated Cu-TFAC), aluminum tris-8hydroxyquinoline (A1g3), lithium quinolate (Liq), tetracyanoquinodimethane (TCNQ), and tetrafluorotetracyanoquinodimethane (F4TCNQ). The electronic structures of these materials were measured with several synchrotron-based x-ray spectroscopies. X-ray photoemission spectroscopy was used to measure the occupied total density of states and the core-level states of the aforementioned materials. X-ray absorption spectroscopy (XAS) was used to probe the element-specific unoccupied partial density of states (PDOS); its angle-resolved variant was used to measure the orientation of the molecules in a film and, in some circumstances, to gauge the extent of an organic film's crystallinity. Most notably, x-ray emission spectroscopy (XES) measures the element- specific occupied PDOS and, when aided by XAS, resonant XES can additionally be used to probe the electronic structure of individual atomic sites within a molecule. Most of the results in this thesis are accompanied by the results of electronic structure calculations determined with density functional theory (DFT). DFT is a useful aid in interpreting the results of the x-ray spectroscopies employed. The experimental results, combined with DFT calculations, provide a wealth of information regarding the electronic structures of these organic materials. v

Unraveling the Mechanism of the Photodeprotection Reaction of 8-Bromo- and 8-Chloro-7-hydroxyquinoline Caged Acetates

PubMed Central

Ma, Jiani; Rea, Adam C; An, Huiying; Ma, Chensheng; Guan, Xiangguo; Li, Ming-De; Su, Tao; Yeung, Chi Shun; Harris, Kyle T; Zhu, Yue; Nganga, Jameil L; Fedoryak, Olesya D; Dore, Timothy M; Phillips, David Lee

2012-01-01

Abstract Photoremovable protecting groups (PPGs) when conjugated to biological effectors forming “caged compounds” are a powerful means to regulate the action of physiologically active messengers in vivo through 1-photon excitation (1PE) and 2-photon excitation (2PE). Understanding the photodeprotection mechanism is important for their physiological use. We compared the quantum efficiencies and product outcomes in different solvent and pH conditions for the photolysis reactions of (8-chloro-7-hydroxyquinolin-2-yl)methyl acetate (CHQ-OAc) and (8-bromo-7-hydroxyquinolin-2-yl)methyl acetate (BHQ-OAc), representatives of the quinoline class of phototriggers for biological use, and conducted nanosecond time-resolved spectroscopic studies using transient emission (ns-EM), transient absorption (ns-TA), transient resonance Raman (ns-TR2), and time-resolved resonance Raman (ns-TR3) spectroscopies. The results indicate differences in the photochemical mechanisms and product outcomes, and reveal that the triplet excited state is most likely on the pathway to the product and that dehalogenation competes with release of acetate from BHQ-OAc, but not CHQ-OAc. A high fluorescence quantum yield and a more efficient excited-state proton transfer (ESPT) in CHQ-OAc compared to BHQ-OAc explain the lower quantum efficiency of CHQ-OAc relative to BHQ-OAc. PMID:22511356

Fluorinated Alq3 derivatives with tunable optical properties.

PubMed

Shi, Yue-Wen; Shi, Min-Min; Huang, Jia-Chi; Chen, Hong-Zheng; Wang, Mang; Liu, Xiao-Dong; Ma, Yu-Guang; Xu, Hai; Yang, Bing

2006-05-14

This communication reports that not only the emission colour but also the photoluminescence quantum yield of Alq3 can be tuned by introducing fluorine atoms at different positions; with fluorination at C-5 the emission is red-shifted with a tremendously decreased intensity, fluorination at C-6 causes a blue-shift with a significantly increased intensity, and fluorination at C-7 has a minor effect on both the colour and intensity of Alq3's emission.

Synthesis Al complex and investigating effect of doped ZnO nanoparticles in the electrical and optical efficiency of OLEDS

NASA Astrophysics Data System (ADS)

Shahedi, Zahra; Jafari, Mohammad Reza

2017-01-01

In this study, an organometallic complex based on aluminum ions is synthesized. And it is utilized as fluorescent material in the organic light-emitting diodes (OLEDs). The synthesized complex was characterized using XRD, UV-Vis, FT-IR as well as PL spectroscopy analyses. The energy levels of Al complex were determined by cyclic voltammetry measurements. Then, the effects of ZnO nanoparticles (NPs) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate), PEDOT:PSS, on the electrical and optical performance of the organic light-emitting diodes have been investigated. For this purpose, two samples containing ITO/PEDOT:PSS/PVK/Alq3/PBD/Al with two different concentration and two samples containing ITO/PEDOT:PSS:ZnO/PVK/Alq3/PBD/Al with two different concentration were prepared. Then, hole transport, electron transport and emissive layers were deposited by the spin coating method and the cathode layer (Al) was deposited by the thermal evaporation method. The OLED simulation was also done by constructing the model and choosing appropriate parameters. Then, the experimental data were collected and the results interpreted both qualitatively and quantitatively. The results of the simulations were compared with experimental data of the J-V spectra. Comparing experimental data and simulation results showed that the electrical and optical efficiency of the samples with ZnO NPs is appreciably higher than the samples without ZnO NPs.

Fabrication of Transparent CNT Films for OLED Application

DTIC Science & Technology

2010-02-04

and a HTL, respectively, and the Alq3 layer adjacent to a composite cathode of LiF/Al was a green-emitting EML . Figure 14 shows that the RMS roughness... EML . Internationale de l’Eclairage chromaticity coordinates CIEx,y of the spectra is (0.32, 0.52) that is very similar (or identical) to the color...coordinates of conventional Alq3 OLEDs. Figure 15: Photographs of the OLED with a SWCNT anode and an Alq3 EML in operation and the corresponding

[A novel yellow organic light-emitting device].

PubMed

Ma, Chen; Wang, Hua; Hao, Yu-Ying; Gao, Zhi-Xiang; Zhou, He-Feng; Xu, Bing-She

2008-07-01

The fabrication of a novel organic yellow-light-emitting device using Rhodamine B as dopant with double quantum-well (DQW) structure was introduced in the present article. The structure and thickness of this device is ITO/CuPc (6 nm) /NPB (20 nm) /Alq3 (3 nm)/Alq3 : Rhodamine B (3 nm) /Alq3 (3 nm) /Al q3 : Rhodamine B(3 nm) /Alq3 (30 nm) /Liq (5 nm)/Al (30 nm). With the detailed investigation of electroluminescence of the novel organic yellow-light-emitting device, the authors found that the doping concentration of Rhodamine B (RhB) had a very big influence on luminance and efficiency of the organic yellow-light-emitting device. When doping concentration of Rhodamine B (RhB) was 1.5 wt%, the organic yellow-light-emitting device was obtained with the maximum current efficiency of 1.526 cd x A(-1) and the maximum luminance of 1 309 cd x m(-2). It can be seen from the EL spectra of the devices that there existed energy transferring from Alq3 to RhB in the organic light-emitting layers. When the doping concentration of RhB increased, lambda(max) of EL spectra redshifted obviously. The phenomenon was attributed to the Stokes effect of quantum wells and self-polarization of RhB dye molecules.

Hydrogen bond assisted interaction of glutamine with chromium (III) complex of 8-hydroxyquinoline: Experimental and theoretical studies

NASA Astrophysics Data System (ADS)

Narayanan, Jayanthi; Carlos-Alberto, Aguilar H.; Arturo, Lazarini M.; Höpfl, Herbert; Enrique-Fernando, Velazquez C.; Fernando, Rocha A.; Fernando-Toyohiko, Wakida K.; Velazquez-Lopez, José E.; Lesli, Arroyo O.

2018-03-01

Chromium (III) complex [Cr (hq)3;C2H5OH] of 8-hydroxyquinoline (hq) was prepared and its structure was resolved by X-ray diffraction analysis at low-temperature, showing that Cr3+ ion presents in distorted octahedral geometry, and it is consistent with the DFT optimized structure. It was observed that solvent ethanol is involved a hydrogen bond with 8-hydroxyquinoline anion. Furthermore, the molecular orbital contributions to spectral bands observed for the complex were determined by TD-DFT. The interaction of [Cr (hq)3;C2H5OH] with glutamine (Gln) or asparagine (Asn) shows that the complex binds effectively with glutamine through hydrogen bonding (H2N+-HṡṡṡOethanol) to form a possible stable adduct [Cr (hq)3;C2H5OH)Gln], yielding its binding constant 10,000 times greater (1.4315 M-1) than that for Asn (5.0 × 10-4 M-1). This is apparently due to the formation of stable secondary coordination sphere through the hydrogen bond between the metal complex with Gln. This observation is good agreement with the total molecular energy as well as with the molecular orbital study, i.e. in the DFT calculation, a lower total molecular energy (-8299,549.441 kcal/mmol) for [Cr (hq)3;C2H5OH) Gln] was obtained than that resulted for [Cr (hq)3;C2H5OH)Asn] (-8194,799.867 kcal/mmol), establishing ethanol effectively stabilizes the interaction between glutamine and the complex. Finally, antibacterial properties of [Cr (hq)3;C2H5OH] against Gram positive Bacillus cereus and Gram negative Escherichia coli was also studied, and compared its bacterial growths for its adducts of glutamine or of asparagine.

5-Carboxy-8-hydroxyquinoline is a Broad Spectrum 2-Oxoglutarate Oxygenase Inhibitor which Causes Iron Translocation

PubMed Central

Aik, WeiShen; Che, Ka Hing; Li, Xuan Shirley; Kristensen, Jan B. L.; King, Oliver N. F.; Chan, Mun Chiang; Yeoh, Kar Kheng; Choi, Hwanho; Walport, Louise J.; Thinnes, Cyrille C.; Bush, Jacob T.; Lejeune, Clarisse; Rydzik, Anna M.; Rose, Nathan R.; Bagg, Eleanor A.; McDonough, Michael A.; Krojer, Tobias; Yue, Wyatt W.; Ng, Stanley S.; Olsen, Lars; Brennan, Paul E.; Oppermann, Udo; Muller-Knapp, Susanne; Klose, Robert J.; Ratcliffe, Peter J.; Schofield, Christopher J.; Kawamura, Akane

2015-01-01

2-Oxoglutarate and iron dependent oxygenases are therapeutic targets for human diseases. Using a representative 2OG oxygenase panel, we compare the inhibitory activities of 5-carboxy-8-hydroxyquinoline (IOX1) and 4-carboxy-8-hydroxyquinoline (4C8HQ) with that of two other commonly used 2OG oxygenase inhibitors, N-oxalylglycine (NOG) and 2,4-pyridinedicarboxylic acid (2,4-PDCA). The results reveal that IOX1 has a broad spectrum of activity, as demonstrated by the inhibition of transcription factor hydroxylases, representatives of all 2OG dependent histone demethylase subfamilies, nucleic acid demethylases and γ-butyrobetaine hydroxylase. Cellular assays show that, unlike NOG and 2,4-PDCA, IOX1 is active against both cytosolic and nuclear 2OG oxygenases without ester derivatisation. Unexpectedly, crystallographic studies on these oxygenases demonstrate that IOX1, but not 4C8HQ, can cause translocation of the active site metal, revealing a rare example of protein ligand-induced metal movement PMID:26682036

Performance Enhancement of Small Molecular Solar Cells by Bilayer Cathode Buffer.

PubMed

Sun, Qinjun; Zhao, Huanbin; Zhou, Miao; Gao, Liyan; Hao, Yuying

2016-04-01

An effective composite bilayer cathode buffer structure is proposed for use in small molecular solar cells. CsF was doped in Alq3 to form the first cathode buffer, leading to small serial resistances. BCP was used as the second cathode buffer to block the holes to the electrode. The optimized bilayer cathode buffer significantly increased the short circuit and fill factor of devices. By integrating this bilayer cathode buffer, the CuPc/C60 small molecular heterojunction cell exhibited a power conversion efficiency of up to 0.8%, which was an improvement of 56% compared to a device with only the Alq3 cathode buffer. Meanwhile, the bilayer cathode buffer still has a good protective effect on the performance of the device.

Controllable synthesis of rice-shape Alq3 nanoparticles with single crystal structure

NASA Astrophysics Data System (ADS)

Xie, Wanfeng; Fan, Jihui; Song, Hui; Jiang, Feng; Yuan, Huimin; Wei, Zhixian; Ji, Ziwu; Pang, Zhiyong; Han, Shenghao

2016-10-01

We report the controllable growth of rice-shape nanoparticles of Alq3 by an extremely facile self-assembly approach. Possible mechanisms have been proposed to interpret the formation and controlled process of the single crystal nanoparticles. The field-emission performances (turn-on field 7 V μm-1, maximum current density 2.9 mA cm-2) indicate the potential application on miniaturized nano-optoelectronics devices of Alq3-based. This facile method can potentially be used for the controlled synthesis of other functional complexes and organic nanostructures.

Energy and charge transfer dynamics between Alq3 and CdSeS nanocrystals.

PubMed

Zhang, Shuping; Liu, Yuqiang; Yang, Yanqiang

2010-03-01

The photoluminescence properties of the blend films consisting of organic small molecules and nanocrystals (NCs)--Alq3 and CdSeS NCs--were studied by steady-state and time-resolved photoluminescence (PL) spectroscopy with different excited wavelengths. Both the fluorescence intensity and lifetime are intensively dependent on the NC concentration. The detailed analysis of experiment data proves that Forster energy transfer from the Alq3 to the NCs exists simultaneously with the charge transfer and both compete with each other in the blend films.

Electrophoretic Characteristics of Outer Membrane Proteins of Neisseria meningitidis,

DTIC Science & Technology

1987-07-01

chemo-organotropic aerobic or facultative microbes, producing catalase and cytochrome oxidase (Morello and Bohnoff, 1980; Reyn, 1974). These bacteria...resolution, the porosity, pH , and TRIS and glycine concentrations in the stacking and separating gels were investigated. The UNCLASSIFIED UNCLASSIFIED /5...stacking gels were 1.7 cm in length and contained, 0.375 M Tris-HCl ( pH 8.8) and 0.1% SDS. The electrode buffer ( pH 8.3 ) consisted of 0.025 M Tris-HCI

Effet de l'énergie du faisceau d'ions servant à l'assistance du dépôt de matériaux organiques utilisés pour réaliser des diodes électroluminescentes

NASA Astrophysics Data System (ADS)

Antony, R.; Moliton, A.; Ratier, B.

1998-06-01

Light emitting diode based on the structure ITO/Alq3/Ca-Al lead to enhanced quantum efficiency when the Alq3 active layer is obtained by IBAD (Ion Beam Assisted Deposition): with Iodine ions, the optimization (quantum efficiency multiplied by a factor10) is obtained for an ion energy equal to 100eV. La réalisation de diodes électroluminescentes basées sur la structure ITO/Alq3/Ca-Al conduit à des performances améliorées lorsque le dépôt de la couche active Alq3 est effectué avec l'assistance d'un faisceau d'ions; l'optimisation (rendement quantique interne accru d'un ordre de grandeur) correspond à des ions Iode d'énergie 100eV.

Challenges and Opportunities for Biophotonic Devices in the Liquid State and the Solid State

DTIC Science & Technology

2006-07-01

of the NPB:Eu device and a baseline device (without the NPB layer and emitting from the Alq3 layer) as a function of current density. The luminance...of the NPB:Eu device is clearly superior, with a maximum of 590 cd/m2 at 375 mA/cm2, whereas the Alq3 OLED peaks at only 45 cd/m2 at 30 mA/cm2...Luminance versus current density for Eu-doped BioLED and for baseline Alq3 device. 1-4244-0078-3/06/$20.00 (c) 2006 IEEE B. Electrofluidic

Coordination-supported organic polymers: mesoporous inorganic–organic materials with preferred stability

DOE PAGES

Chen, Dong; Zhang, Pengfei; Fang, Qianrong; ...

2018-01-01

A simple and versatile strategy is developed for the synthesis of coordination-supported organic polymers(COPs) via coordination between Al 3+ and 5-amino-8-hydroxyquinoline together with organic imine- or imide-based polycondensation.

Coordination-supported organic polymers: mesoporous inorganic–organic materials with preferred stability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Dong; Zhang, Pengfei; Fang, Qianrong

A simple and versatile strategy is developed for the synthesis of coordination-supported organic polymers(COPs) via coordination between Al 3+ and 5-amino-8-hydroxyquinoline together with organic imine- or imide-based polycondensation.

Direct Observation of the Evolution of Both the HOMO and LUMO Energy Levels of a Silole Derivative at a Magnesium/Silole Interface

DTIC Science & Technology

2004-01-01

transport gap has been observed in K-intercalated Alq3 films, where the HOMO - Proc. of SPIE Vol. 5214 371 LUMO on-set separation is 3.05 ± 0.1 eV...while in a neat Alq3 film, the transport gap is 3.9 ± 0.4 eV. 22,25 Narrowing of the transport gap of alkali-fulleride films (K3C60, K6C60) has also...Rajagopal and A. Kahn, “Photoemission spectroscopy investigation of magnesium– Alq3 interfaces“, J. Appl. Phys. 84, pp. 355-358, 1998. 9 M. G. Mason

Deposition of functional nanoparticle thin films by resonant infrared laser ablation.

NASA Astrophysics Data System (ADS)

Haglund, Richard; Johnson, Stephen; Park, Hee K.; Appavoo, Kannatessen

2008-03-01

We have deposited thin films containing functional nanoparticles, using tunable infrared light from a picosecond free-electron laser (FEL). Thin films of the green light-emitting molecule Alq3 were first deposited by resonant infrared laser ablation at 6.68 μm, targeting the C=C ring mode of the Alq3. TiO2 nanoparticles 50-100 nm diameter were then suspended in a water matrix, frozen, and transferred by resonant infrared laser ablation at 2.94 μm through a shadow mask onto the Alq3 film. Photoluminescence was substantially enhanced in the regions of the film covered by the TiO2 nanoparticles. In a second experiment, gold nanoparticles with diameters in the range of 50-100 nm were suspended in the conducting polymer and anti-static coating material PEDOT:PSS, which was diluted by mixing with N-methyl pyrrolidinone (NMP). The gold nanoparticle concentration was 8-10% by weight. The mixture was frozen and then ablated by tuning the FEL to 3.47 μm, the C-H stretch mode of NMP. Optical spectroscopy of the thin film deposited by resonant infrared laser ablation exhibited the surface-plasmon resonance characteristic of the Au nanoparticles. These experiments illustrate the versatility of matrix-assisted resonant infrared laser ablation as a technique for depositing thin films containing functionalized nanoparticles.

Spectroscopic analysis of 8-hydroxyquinoline derivatives and investigation of its reactive properties by DFT and molecular dynamics simulations

NASA Astrophysics Data System (ADS)

Sureshkumar, B.; Mary, Y. Sheena; Resmi, K. S.; Panicker, C. Yohannan; Armaković, Stevan; Armaković, Sanja J.; Van Alsenoy, C.; Narayana, B.; Suma, S.

2018-03-01

Two 8-hydroxyquinoline derivatives, 5,7-dichloro-8-hydroxyquinoline (57DC8HQ) and 5-chloro-7-iodo-8-hydroxy quinoline (5CL7I8HQ) have been investigated in details by means of spectroscopic characterization and computational molecular modelling techniques. FT-IR and FT-Raman experimental spectroscopic approaches have been utilized in order to obtain detailed spectroscopic signatures of title compounds, while DFT calculations have been used in order to visualize and assign vibrations. The computed values of dipole moment, polarizability and hyperpolarizability indicate that the title molecules exhibit NLO properties. The evaluated HOMO and LUMO energies demonstrate the chemical stability of the molecules. NBO analysis is made to study the stability of the molecules arising from hyperconjugative interactions and charge delocalization. DFT calculations have been also used jointly with MD simulations in order to investigate in details global and local reactivity properties of title compounds. Also, molecular docking has been also used in order to investigate affinity of title compounds against decarboxylase inhibitor and quinoline derivatives can be a lead compounds for developing new antiparkinsonian drug.

A novel dichromate-sensitive fluorescent nano-chemosensor using new functionalized SBA-15.

PubMed

Hosseini, Morteza; Gupta, Vinod Kumar; Ganjali, Mohammad Reza; Rafiei-Sarmazdeh, Zahra; Faridbod, Farnoush; Goldooz, Hassan; Badiei, Ali Reza; Norouzi, Parviz

2012-02-17

A novel fluorescence nano-chemosensor for Cr(2)O(7)(2-) anion has been developed by assembly of fluorescent aluminum complex of 8-hydroxyquinoline (AlQ(x)) within the channels of modified SBA-15. SBA-SPS-AlQ(x) shows a fluorescence emission at 486 nm. The observed remarkable fluorescence of SBA-SPS-AlQ(x) quenches in presence of Cr(2)O(7)(2-) anion. The results showed that this fluorescent nano-material can be a useful chemo-sensor for determination of dichromate anions in aqueous solutions. The linear detecting range of fluorescent nano-chemosensor for Cr(2)O(7)(2-) anion was 0.16-2.9 μmol L(-1). The lowest limit of detection (LDL) was also found to be 0.2 ng mL(-1) in aqueous solutions. SBA-SPS-AlQ(x) showed selectively and sensitively fluorescent quenching response toward Cr(2)O(7)(2-) ion in comparison with I(3)(-), NO(3)(-), CN(-), CO(3)(2-), Br(-), Cl(-), F(-), H(2)PO(4)(-) and SO(4)(2-) ions, which was because of the higher stability of its inorganic complex with dichromate ion. Copyright © 2011 Elsevier B.V. All rights reserved.

Heterocycles Based on Group III, IV, and V Elements, Precursors for Novel Glasses and Ceramics

DTIC Science & Technology

1990-08-01

OF TABLES v LIST OF FIGURES vi 1. ABSTRACT 1 2. INTRODUCTION 3 3. RESULTS AND DISCUSSION 5 3.1 Synthesis and Thermolysis of Aluminum...Chloride.Hexamethyldisilazane Adduct 5 3.2 Synthesis and Reactions of Bis(trimethylsilyl)- aminoaluminum Compounds 11 3.3 Reactions of Tris[bis(trimethylsilyl)amino...Et3N.C12AIN(SiMe3 )B(NH2 )NHSiMe3 , a processible precursor to AlN.BN ceramic. Attempts at synthesis of other AlN.BN precursors and AINP systems were

8-Hydroxyquinolines: a review of their metal chelating properties and medicinal applications

PubMed Central

Prachayasittikul, Veda; Prachayasittikul, Supaluk; Ruchirawat, Somsak; Prachayasittikul, Virapong

2013-01-01

Metal ions play an important role in biological processes and in metal homeostasis. Metal imbalance is the leading cause for many neurodegenerative diseases such as Alzheimer’s disease, Parkinson’s disease, and multiple sclerosis. 8-Hydroxyquinoline (8HQ) is a small planar molecule with a lipophilic effect and a metal chelating ability. As a result, 8HQ and its derivatives hold medicinal properties such as antineurodegenerative, anticancer, antioxidant, antimicrobial, anti-inflammatory, and antidiabetic activities. Herein, diverse bioactivities of 8HQ and newly synthesized 8HQ-based compounds are discussed together with their mechanisms of actions and structure–activity relationships. PMID:24115839

Solvent-induced controllable synthesis, single-crystal to single-crystal transformation and encapsulation of Alq3 for modulated luminescence in (4,8)-connected metal-organic frameworks.

PubMed

Lan, Ya-Qian; Jiang, Hai-Long; Li, Shun-Li; Xu, Qiang

2012-07-16

In this work, for the first time, we have systematically demonstrated that solvent plays crucial roles in both controllable synthesis of metal-organic frameworks (MOFs) and their structural transformation process. With solvent as the only variable, five new MOFs with different structures have been constructed, in which one MOF undergoes solvent-induced single-crystal to single-crystal (SCSC) transformation that involves not only solvent exchange but also the cleavage and formation of coordination bonds. Particularly, a significant crystallographic change has been realized through an unprecedented three-step SCSC transformation process. Furthermore, we have demonstrated that the obtained MOF could be an excellent host for chromophores such as Alq3 for modulated luminescent properties.

Novel Na(+) doped Alq3 hybrid materials for organic light-emitting diode (OLED) devices and flat panel displays.

PubMed

Bhagat, S A; Borghate, S V; Kalyani, N Thejo; Dhoble, S J

2015-05-01

Pure and Na(+) -doped Alq3 complexes were synthesized by a simple precipitation method at room temperature, maintaining a stoichiometric ratio. These complexes were characterized by X-ray diffraction, Fourier transform infrared (FTIR), UV/Vis absorption and photoluminescence (PL) spectra. The X-ray diffractogram exhibits well-resolved peaks, revealing the crystalline nature of the synthesized complexes, FTIR confirms the molecular structure and the completion of quinoline ring formation in the metal complex. UV/Vis absorption and PL spectra of sodium-doped Alq3 complexes exhibit high emission intensity in comparison with Alq3 phosphor, proving that when doped in Alq3 , Na(+) enhances PL emission intensity. The excitation spectra of the synthesized complexes lie in the range 242-457 nm when weak shoulders are also considered. Because the sharp excitation peak falls in the blue region of visible radiation, the complexes can be employed for blue chip excitation. The emission wavelength of all the synthesized complexes lies in the bluish green/green region ranging between 485 and 531 nm. The intensity of the emission wavelength was found to be elevated when Na(+) is doped into Alq3 . Because both the excitation and emission wavelengths fall in the visible region of electromagnetic radiation, these phosphors can also be employed to improve the power conversion efficiency of photovoltaic cells by using the solar spectral conversion principle. Thus, the synthesized phosphors can be used as bluish green/green light-emitting phosphors for organic light-emitting diodes, flat panel displays, solid-state lighting technology - a step towards the desire to reduce energy consumption and generate pollution free light. Copyright © 2014 John Wiley & Sons, Ltd.

Biopolymers in Light Emitting Devices

DTIC Science & Technology

2006-09-01

from an Alq3 layer are illustrated in Fig. 4. Red emission from the rare earth ion Eu3+ doped into the various emitter layers has also been...structure. 26 • IDRC 3.2 / A. J. Steckl Figure 4. DNA BioLEDs: (a) blue (NPB) and green ( Alq3 ) emitting devices in operation; (b) luminance

Studies on the growth, structural, optical, mechanical properties of 8-hydroxyquinoline single crystal by vertical Bridgman technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prabhakaran, SP.; Babu, R. Ramesh, E-mail: rampap2k@yahoo.co.in; Velusamy, P.

2011-11-15

Highlights: {yields} Growth of bulk single crystal of 8-hydroxyquinoline (8-HQ) by vertical Bridgman technique for the first time. {yields} The crystalline perfection is reasonably good. {yields} The photoluminescence spectrum shows that the material is suitable for blue light emission. -- Abstract: Single crystal of organic nonlinear optical material, 8-hydroxyquinoline (8-HQ) of dimension 52 mm (length) x 12 mm (dia.) was grown from melt using vertical Bridgman technique. The crystal system of the material was confirmed by powder X-ray diffraction analysis. The crystalline perfection of the grown crystal was examined by high-resolution X-ray diffraction study. Low angular spread around 400'' ofmore » the diffraction curve and the low full width half maximum values show that the crystalline perfection is reasonably good. The recorded photoluminescence spectrum shows that the material is suitable for blue light emission. Optical transmittance for the UV and visible region was measured and mechanical strength was estimated from Vicker's microhardness test along the growth face of the grown crystal.« less

P3HT:PCBM-based organic solar cells : Optimisation of active layer nanostructure and interface properties

NASA Astrophysics Data System (ADS)

Kadem, Burak Yahya

Organic solar cells (OSCs) have attracted a significant attention during the last decade due to their simple processability on a flexible substrate as well as scope for large-scale production using role to role technique. Improving the performance of the organic solar cells and their lifetime stability are one of the main challenges faced by researchers in this field. In this thesis, work has been carried out using a blend of Poly(3-hexylthiophene-2,5-diyl) (P3HT) and [6,6]-Phenyl C[61] butyric acid methyl ester (PCBM) as an active layer in the ratio of (1:1) (P3HT:PCBM). The efficiency and stability of P3HT:PCBM-based solar cells have been examined using different methods and employing novel materials such as1-[N-(2-ethoxyethyl) pent-4-ynamide] -8 (11), 15 (18), 22 (25) -tris-{2-[2-(2-ethoxyethoxy) ethoxy]-1-[2-((2- ethoxyethoxy) - ethoxy) methyl] ethyloxy} phthalocyaninato zinc (II) (ZnPc) to construct a ternary hybrid as the active layer. Controlling the morphology and crystallinity of P3HT:PCBM active layer was carried out using different solvents including chloroform (CF), chlorobenzene (CB) and dichlorobenzene (DCB) and their co-solvents in the ratio of (1:1) to dissolve the P3HT:PCBM blend. Optimum morphology and crystallinity were achieved using a co-solvent made of CB:CF with the obtained solar cell exhibiting the highest performance with PCE reaching 2.73% among other devices prepared using different solvents. Further device performance improvement was observed through optimization of active layer thickness with studied thickness falling in range 65-266 nm. Measurements of the PV characteristics of the investigated OSC devices have revealed optimum performance when active layer thickness was 95 nm with PCE=3.846%. The stability of the P3HT:PCBM-based devices on optimisation of the active layer thickness has shown a decrease in PCE of about 71% over a period of 41 days. Furthermore, P3HT has been blended with different fullerene derivatives (PC[60]BM, PC[61]BM, PC[70]BM and PC[71]BM) and the active layers were processed using the optimum solvent as well as optimum film's thickness.These PCBM derivatives have different lower unoccupied molecular level (LUMO) and different higher occupied molecular level (HOMO) positions, which subsequently influence the PV parameters of the OSCs such as the device open circuit voltage (V[oc]) and its built-in potential (V[bi]). P3HT:PC61BM-based blend has exhibited the highest device performance with PCE reaching 4.2%. Using the above mentioned optimum parameters, the P3HT:PCBM-based devices have been subjected to post-deposition annealing at different temperatures in the range 100-180°C. Efficient device performance was ascribed to P3HT:PCBM layers being subjected to post-deposition heat treatment at 140°C with PCE=5.5%. Device stability as a result of post-deposition heat treatment has also been shown to improve with PCE degrading by about 38% after 55 days.The use of interfacial layer is found to play a key part in modifying the solar cell performance; using electron transport layer (ETL) such as aluminium tris(8-hydroxyquinoline) (Alq3) as a solution processable layer has contributed in increasing PCE to 4.25%, while, using PEDOT:PSS as a hole transport layer (HTL) doped with metal salts has significantly contributed in increasing PCE to reach 6.82% in device when PEDOT:PSS was doped with LiCl aqueous solution. Stability study for the device based on HTL has shown degradation in the PCE from 6.82% to around 1% over 96 days. Using ETL and HTL simultaneously in a complete device has shown a further enhanced PCE reaching 7%. In a further study, doping the P3HT:PCBM with the novel ZnPc hybrids (SWCNTs and reduced graphene oxide (rGO) are covalently and non-covalently functionalised to ZnPc) with the weight ratio of (1:0.01) has significantly altered the solar cell device properties. The best performance is based on P3HT:PCBM blended with ZnPc-SWCNTs-co bonded as a ternary active layer demonstrating device PCE of 5.3% compared to a reference device based on bare P3HT:PCBM blend with PCE of 3.46%.

Laser-Activated Metal Deposition.

DTIC Science & Technology

1988-01-31

Quartz F "" (0.1 Mm film thickness) AI-4N N APPENDIX 2 SYNTHESIS OF ORGANOMETALLIC COMPOUNDS p 1 . SYNTHESIS OF COPPER BIS HEXAFLUOROACETYLACETONATE...point. 2. SYNTHESIS OF CHROMIUM TRIS HEXAFLUOROACETYLACETONATE (Procedure of R. E. Sievers, et al., Inorg. Chem, 1 , 966 (1962)) A mixture of chromium...The precipi- tate was filtered and recrystallized in carbon tetrachloride to yield about 1 g of brownish-green crystals. 3. SYNTHESIS OF ALUMINUM

DNA as an Optical Material

DTIC Science & Technology

2011-07-01

the electron blocking function of the DNA layer; electroluminescence occurs in either the AlQ3 (green) or NPB layer (blue) layers. Source: J. A...been observed for sev- eral fluorescent materials with different HOMO/LUMO levels, including AlQ3 (green emission) and NPB (blue emission). OLEDs

40 CFR 180.415 - Aluminum tris (O-ethylphosphonate); tolerances for residues.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific.... Commodity Parts per million Asparagus 0.1 Grape 10 (d) Indirect or inadvertent residues. [Reserved] [64 FR...

Postmodification of MOF-5 using secondary complex formation using 8- hydroxyquinoline (HOQ) for the development of visible light active photocatalysts

NASA Astrophysics Data System (ADS)

Thakare, Sanjay R.; Ramteke, Shruti M.

2018-05-01

A novel HOQ@MOF-5 compound photocatalyst was successfully constructed by interacting 8- Hydroxyquinoline with MOF-5 synthesized through a room temperature method. The secondary complex formation between the Zn cluster with 8-Hydroxyquinoline harnessed visible light and acted as a mediator to transfer photoinduced electrons to MOF-5 for enhancing the photocatalytic reaction rate with visible light. HOQ@MOF-5 was characterized by various spectroscopic techniques, such as XRD showing the crystalline nature of compound, UV-Visible spectroscopy showing the 2.54 eV band gap of HOQ@MOF-5 and morphological analysis tools, such as the nanoparticle nature of the compound with 9.561 nm particle size. The photocatalytic effect was estimated using the photocatalytic degradation of phenol as a representative organic pollutant under visible light irradiation. This work provides a new compound acting as source of electrons transfer for the development of efficient photocatalysts for remediation of environmental pollution.

A flexible top-emitting organic light-emitting diode on steel foil

NASA Astrophysics Data System (ADS)

Xie, Zhiyuan; Hung, Liang-Sun; Zhu, Furong

2003-11-01

An efficient flexible top-emitting organic light-emitting diode (FTOLED) was developed on a thin steel foil. The FTOLED was constructed on the spin-on-glass (SOG)-coated steel substrate with an organic stack of NPB/Alq 3 sandwiched by a highly reflective Ag anode and a semitransparent Sm cathode. An ultrathin plasma-polymerized hydrocarbon film (CF X) was interposed between the Ag anode and the NPB layer to enhance hole-injection, and an additional Alq 3 layer was overlaid on the Sm cathode to increase light output. The FTOLED showed a peak efficiency of 4.4 cd/A higher than 3.7 cd/A of a convention NPB/Alq 3-based bottom-emitting OLED.

Quantitative Determining of Ultra-Trace Aluminum Ion in Environmental Samples by Liquid Phase Microextraction Assisted Anodic Stripping Voltammetry.

PubMed

Zhang, Liuyang; Luo, Jinju; Shen, Xinyu; Li, Chunya; Wang, Xian; Nie, Bei; Fang, Huaifang

2018-05-10

Direct detecting of trace amount Al(III) in aqueous solution by stripping voltammetry is often frustrated by its irreversible reduction, resided at −1.75 V (vs. Ag/AgCl reference), which is in a proximal potential of proton reduction. Here, we described an electroanalytical approach, combined with liquid phase microextraction (LPME) using ionic liquid (IL), to quantitatively assess trace amount aluminum in environmental samples. The Al(III) was caged by 8-hydroxyquinoline, forming a superb hydrophobic metal⁻chelate, which sequentially transfers and concentrates in the bottom layer of IL-phase during LPME. The preconcentrated Al(III) was further analyzed by a square-wave anodic stripping voltammetry (SW-ASV). The resulting Al-deposited electrodes were characterized by scanning electron microscopy and powder X-ray diffraction, showing the intriguing amorphous nanostructures. The method developed provides a linear calibration ranging from 0.1 to 1.2 ng L −1 with a correlation coefficient of 0.9978. The LOD attains as low as 1 pmol L −1 , which reaches the lowest report for Al(III) detection using electroanalytical techniques. The applicable methodology was implemented for monitoring Al(III) in commercial distilled water.

Alq3 nanorods: promising building blocks for optical devices.

PubMed

Chen, Wei; Peng, Qing; Li, Yadong

2008-07-17

Monodisperse Alq3 nanorods with hexagonal-prism-like morphology are produced via a facile, emulsion based synthesis route. The photoluminescence of individual nanorods differs from the bulk material. These nanorods are promising building blocks for novel optical devices. Copyright © 2008 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cyclodextrin Nanoparticles Bearing 8-Hydroxyquinoline Ligands as Multifunctional Biomaterials.

PubMed

Oliveri, Valentina; Bellia, Francesco; Vecchio, Graziella

2017-03-28

Cyclodextrins are used as building blocks for the development of a host of polymeric biomaterials. The cyclodextrin polymers have found numerous applications as they exhibit unique features such as mechanical properties, stimuli responsiveness and drug loading ability. Notwithstanding the abundance of cyclodextrin polymers studied, metal-chelating polymers based on cyclodextrins have been poorly explored. Herein we report the synthesis and the characterization of the first metal-chelating β-cyclodextrin polymer bearing 8-hydroxyquinoline ligands. The metal ions (Cu 2+ or Zn 2+ ) can modulate the assembly of the polymer nanoparticles. Moreover, the protective activity of the new chelating polymer against self- and metal-induced Aβ aggregation and free radical species are significantly higher than those of the parent compounds. These synergistic effects suggest that the incorporation of hydroxyquinoline moieties into a soluble β-cyclodextrin polymer could represent a promising strategy to design multifunctional biomaterials. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

National Manpower Inventory. Volume 3. Technical Documentation for Software for the Model

DTIC Science & Technology

1985-09-01

Technician APS-96 Search Radar IMA Technician USM-449 (V) & AAI 5500 Series ATE Int Maintenance Level Tech. CO CP-413/ASA-27A SACE TesI Bench IMA...MATE) Test Console IMA Technician ALQ-91/108 DECM IMA Technician ALQ-99 ECM Jammer/Tmilter & ALM-107 TesI Console IMA Technician ALQ-99 ECM Track...Receivers & ALM-109 TesI Console IMA Technician ECM Systems Intermediate Maintenance Technician ASM-347 (GT-1) SACE Programmer/Mainlenanca IMA

Modulating the single-molecule magnet behaviour in phenoxo-O bridged Dy2 systems via subtle structural variations

NASA Astrophysics Data System (ADS)

Wang, Wen-Min; Zhao, Xiao-Yu; Qiao, Hui; Bai, Li; Han, Hong-Fei; Fang, Ming; Wu, Zhi-Lei; Zou, Ji-Yong

2017-09-01

In search of simple approaches to rationally modulate the single-molecule magnet behaviour in polynuclear lanthanide compound, a new system containing two structurally closely related dinuclear dysprosium complexes, namely [Dy2(hfac)4L2] (1) and [Dy2(hfac)4L‧2] (2) (hfac = hexafluoroacetylacetonate, HL = 2-[4-methylaniline-imino]methyl]-8-hydroxyquinoline and HL' = 2-[(3,4-dimethylaniline)-imino]methyl]-8-hydroxyquinoline), are successfully synthesized and the structure-dependent magnetic properties are investigated. The two Dy2 compounds display only slight variations in the coordination geometries of the center Dy(III) ion but display remarkably different single-molecule magnet behaviors with the anisotropic barriers (ΔE/kB) of 9.91 K for 1 and 20.57 K for 2. The different magnetic relaxation behaviors of the two Dy2 complexes mainly originate from the different chemical environments of the central DyIII ions.

A white organic light emitting diode based on anthracene-triphenylamine derivatives

NASA Astrophysics Data System (ADS)

Jiang, Quan; Qu, Jianjun; Yu, Junsheng; Tao, Silu; Gan, Yuanyuan; Jiang, Yadong

2010-10-01

White organic lighting-diode (WOLED) can be used as flat light sources, backlights for liquid crystal displays and full color displays. Recently, a research mainstream of white OLED is to develop the novel materials and optimize the structure of devices. In this work a WOLED with a structure of ITO/NPB/PAA/Alq3: x% rubrene/Alq3/Mg: Ag, was fabricated. The device has two light-emitting layers. NPB is used as a hole transport layer, PAA as a blue emitting layer, Alq3: rubrene host-guest system as a yellow emitting layer, and Alq3 close to the cathode as an electron transport layer. In the experiment, the doping concentration of rubrene was optimized. WOLED 1 with 4% rubrene achieved a maximum luminous efficiency of 1.80 lm/W, a maximum luminance of 3926 cd/m2 and CIE coordinates of (0.374, 0.341) .WOLED 2 with 2% rubrene achieved a maximum luminous efficiency of 0.65 lm/W, a maximum luminance of 7495cd/m2 and CIE coordinates of (0.365,0.365).

[The photoluminescence characteristics of organic multilayer quantum wells].

PubMed

Zhao, De-Wei; Song, Shu-Fang; Zhao, Su-Ling; Xu, Zheng; Wang, Yong-Sheng; Xu, Xu-Rong

2007-04-01

By the use of multi-source high-vaccum organic beam deposition system, the authors prepared organic multilayer quantum well structures, which consist of alternate organic small molecule materials PBD and Alq3. Based on 4-period organic quantum wells, different samples with different thickness barriers and wells were prepared. The authors measured the lowest unoccupied molecular orbit (LUMO) and the highest occupied molecular orbit (HOMO) by electrochemistry cyclic voltammetry and optical absorption. From the energy diagrams, it seems like type-I quantum well structures of the inorganic semiconductor, in which PBD is used as a barrier layer and Alq3 as a well layer and emitter. From small angle X-ray diffraction measurements, the results indicate that these structures have high interface quality and uniformity. The photoluminescence characteristics of organic multilayer quantum wells were investigated. The PL peak has a blue-shift with the decrease of the well layer thickness. Meanwhile as the barrier thickness decreases the PL peaks of PBD disappear gradually. And the energy may be effectively transferred from PBD to Alq3, inducing an enhancement of the luminescence of Alq3.

Synthesis and characterization of pure and Li⁺ activated Alq₃ complexes for green and blue organic light emitting diodes and display devices.

PubMed

Bhagat, S A; Borghate, S V; Kalyani, N Thejo; Dhoble, S J

2014-08-01

Pure and Li(+)-doped Alq3 complexes were synthesized by simple precipitation method at room temperature, maintaining the stoichiometric ratio. These complexes were characterized by X-ray diffraction, ultraviolet-visible absorption and Fourier transform infrared and photoluminescence (PL) spectra. X-ray diffraction analysis reveals the crystalline nature of the synthesized complexes, while Fourier transform infrared spectroscopy confirm the molecular structure, the completion of quinoline ring formation and presence of quinoline structure in the metal complex. Ultraviolet-visible and PL spectra revealed that Li(+) activated Alq3 complexes exhibit the highest intensity in comparison to pure Alq3 phosphor. Thus, Li(+) enhances PL emission intensity when doped into Alq3 phosphor. The excitation spectra lie in the range of 383-456 nm. All the synthesized complexes other than Liq give green emission, while Liq gives blue emission with enhanced intensity. Thus, he synthesized phosphors are the best suitable candidates for green- and blue-emitting organic light emitting diode, PL liquid-crystal display and solid-state lighting applications. Copyright © 2013 John Wiley & Sons, Ltd.

The fabrication of small molecule organic light-emitting diode pixels by laser-induced forward transfer

NASA Astrophysics Data System (ADS)

Shaw-Stewart, J. R. H.; Mattle, T.; Lippert, T. K.; Nagel, M.; Nüesch, F. A.; Wokaun, A.

2013-01-01

Laser-induced forward transfer (LIFT) is a versatile organic light-emitting diode (OLED) pixel deposition process, but has hitherto been applied exclusively to polymeric materials. Here, a modified LIFT process has been used to fabricate small molecule Alq3 organic light-emitting diodes (SMOLEDs). Small molecule thin films are considerably more mechanically brittle than polymeric thin films, which posed significant challenges for LIFT of these materials. The LIFT process presented here uses a polymeric dynamic release layer, a reduced environmental pressure, and a well-defined receiver-donor gap. The Alq3 pixels demonstrate good morphology and functionality, even when compared to conventionally fabricated OLEDs. The Alq3 SMOLED pixel performances show a significant amount of fluence dependence, not observed with polymerical OLED pixels made in previous studies. A layer of tetrabutyl ammonium hydroxide has been deposited on top of the aluminium cathode, as part of the donor substrate, to improve electron injection to the Alq3, by over 600%. These results demonstrate that this variant of LIFT is applicable for the deposition of functional small molecule OLEDs as well as polymeric OLEDs.

Growth Assisted by Glancing Angle Deposition: A New Technique to Fabricate Highly Porous Anisotropic Thin Films.

PubMed

Sanchez-Valencia, Juan Ramon; Longtin, Remi; Rossell, Marta D; Gröning, Pierangelo

2016-04-06

We report a new methodology based on glancing angle deposition (GLAD) of an organic molecule in combination with perpendicular growth of a second inorganic material. The resulting thin films retain a very well-defined tilted columnar microstructure characteristic of GLAD with the inorganic material embedded inside the columns. We refer to this new methodology as growth assisted by glancing angle deposition or GAGLAD, since the material of interest (here, the inorganic) grows in the form of tilted columns, though it is deposited under a nonglancing configuration. As a "proof of concept", we have used silver and zinc oxide as the perpendicularly deposited material since they usually form ill-defined columnar microstructures at room temperature by GLAD. By means of our GAGLAD methodology, the typical tilted columnar microstructure can be developed for materials that otherwise do not form ordered structures under conventional GLAD. This simple methodology broadens significantly the range of materials where control of the microstructure can be achieved by tuning the geometrical deposition parameters. The two examples presented here, Ag/Alq3 and ZnO/Alq3, have been deposited by physical vapor deposition (PVD) and plasma enhanced chemical vapor deposition (PECVD), respectively: two different vacuum techniques that illustrate the generality of the proposed technique. The two type of hybrid samples present very interesting properties that demonstrate the potentiality of GAGLAD. On one hand, the Ag/Alq3 samples present highly optical anisotropic properties when they are analyzed with linearly polarized light. To our knowledge, these Ag/Alq3 samples present the highest angular selectivity reported in the visible range. On the other hand, ZnO/Alq3 samples are used to develop highly porous ZnO thin films by using Alq3 as sacrificial material. In this way, antireflective ZnO samples with very low refractive index and extinction coefficient have been obtained.

76 FR 23490 - Aluminum tris (O

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-27

... code 112). Food manufacturing (NAICS code 311). Pesticide manufacturing (NAICS code 32532). This... used to avoid contamination of food, feed, or food-contact/feed-contact surfaces. Compliance with the... are an agricultural producer, food manufacturer, or pesticide manufacturer. Potentially affected...

Seasonal change in the level and the chemical forms of aluminum in soil solution under a Japanese cedar forest.

PubMed

Umemura, Tomonari; Usami, Yosuke; Aizawa, Sho-ichi; Tsunoda, Kin-ichi; Satake, Ken-ichi

2003-12-30

The level of dissolved aluminum and its chemical forms in soil solutions consecutively collected by a porous cup vacuum sampler were monitored over a period from January 2001 to December 2001 at a Japanese cedar (Cryptomeria japonica) forestry area susceptible to acid deposition to characterize current soil dynamics and to evaluate potential tree damages. Distinction and characterization of Al species with differential toxicities were performed by two complementary speciation techniques; cation-exchange HPLC with fluorometric detection using 8-hydroxyquinoline-5-sulfonic acid (HQS) and size-fractionation/inductively coupled plasma atomic emission spectrometry (ICP-AES). The concentrations of free Al (mainly Al3+ and Al(OH)2+) and inert Al (existing as the complexed and/or colloidal forms) ranged between 0-150 microM and 10-50 microM, respectively. The concentrations of inert Al were mostly below 40 microM during an annual cycle and showed no marked seasonal variation, while free Al concentrations showed a clear tendency to increase in the spring and summer seasons (in the period from April to August) probably due to the enhanced activity of microbial nitrification and the resultant soil acidification. Major cations and anions were also regularly determined and their seasonal changes were correlated with that of the dissolved Al concentration. Correlations between total Al (mainly existing as free Al) and the related species (and environmental conditions) were as follows: Al and Mg (R=0.96, P<0.01), Al and Ca (R=0.97, P<0.01), Al and NO3- (R=0.68, P<0.01), Al and temperature (R=0.68, P<0.01), Al and solution pH (R=-0.61, P<0.01), solution pH and NO3- (R=-0.65, P<0.01).

DNA-Binding Interaction Studies of Microwave Assisted Synthesized Sulfonamide Substituted 8-Hydroxyquinoline Derivatives.

PubMed

Dixit, Ritu B; Patel, Tarosh S; Vanparia, Satish F; Kunjadiya, Anju P; Keharia, Harish R; Dixit, Bharat C

2011-01-01

Sulfonamide substituted 8-hydroxyquinoline derivatives were prepared using a microwave synthesizer. The interaction of sulfonamide substituted 8-hydroxyquinoline derivatives and their transition metal complexes with Plasmid (pUC 19) DNA and Calf Thymus DNA were investigated by UV spectroscopic studies and gel electrophoresis measurements. The interaction between ligand/metal complexes and DNA was carried out by increasing the concentration of DNA from 0 to 12 μl in UV spectroscopic study, while the concentration of DNA in gel electrophoresis remained constant at 10 μl. These studies supported the fact that, the complex binds to DNA by intercalation via ligand into the base pairs of DNA. The relative binding efficacy of the complexes to DNA was much higher than the binding efficacy of ligands, especially the complex of Cu-AHQMBSH had the highest binding ability to DNA. The mobility of the bands decreased as the concentration of the complex was increased, indicating that there was increase in the interaction between the metal ion and DNA. Complexes of AHQMBSH were excellent for DNA binding as compared to HQMABS.

Development of a rapid and sensitive method for the determination of aluminum by reverse-phase high-performance liquid chromatography using a fluorescence detector.

PubMed

Heena; Kumar, Rajesh; Rani, Susheela; Malik, Ashok Kumar

2015-01-01

This study represents a new analytical high-performance liquid chromatography-fluorescence detector method for the determination of Al(III) as Al(III) complex with 8-hydroxyquinoline-5-sulfonic acid in a tap water sample and a coke sample. A micellar liquid chromatographic method is proposed for the determination of aluminum metal in the presence of cetyltrimethylammonium bromide, a cationic surfactant (0.05 M) used for the solubilization of the aluminum complex. The influence of pH and ligand concentration on the formation of the complex was studied by adding a small amount of 0.1 M sodium hydroxide. The metal chelate was detected at λEx 410 nm and λEm 510 nm. This method eliminates the need for addition of reagent or organic modifier to the mobile phase. The complex was analyzed using an Ascentis Express C18 column and a mobile phase consisting of acetonitrile, methanol and water (55 : 30 : 15). Under the optimized conditions, the linear range was 1-200 µg L(-1) and the limit of detection was 0.05 µg L(-1). The method showed a good detector response over the range of interest and was successfully applied for the determination of trace Al(III) in canned coke and water samples containing excess of Mg(II), Ca(II) and other matrices. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Ca/Alq3 hybrid cathode buffer layer for the optimization of organic solar cells based on a planar heterojunction

NASA Astrophysics Data System (ADS)

El Jouad, Z.; Barkat, L.; Stephant, N.; Cattin, L.; Hamzaoui, N.; Khelil, A.; Ghamnia, M.; Addou, M.; Morsli, M.; Béchu, S.; Cabanetos, C.; Richard-Plouet, M.; Blanchard, P.; Bernède, J. C.

2016-11-01

Use of efficient anode cathode buffer layer (CBL) is crucial to improve the efficiency of organic photovoltaic cells. Here we show that using a double CBL, Ca/Alq3, allows improving significantly cell performances. The insertion of Ca layer facilitates electron harvesting and blocks hole collection, leading to improved charge selectivity and reduced leakage current, whereas Alq3 blocks excitons. After optimisation of this Ca/Alq3 CBL using CuPc as electron donor, it is shown that it is also efficient when SubPc is substituted to CuPc in the cells. In that case we show that the morphology of the SubPc layer, and therefore the efficiency of the cells, strongly depends on the deposition rate of the SubPc film. It is necessary to deposit slowly (0.02 nm/s) the SubPc films because at higher deposition rate (0.06 nm/s) the films are porous, which induces leakage currents and deterioration of the cell performances. The SubPc layers whose formations are kinetically driven at low deposition rates are more uniform, whereas those deposited faster exhibit high densities of pinholes.

Influence of Pentacene Interface Layer in ITO/α-NPD/Alq3/Al Organic Light Emitting Diodes by Time-Resolved Electric-Field-Induced Optical Second-Harmonic Generation Measurement.

PubMed

Oda, Yoshiaki; Sadakata, Atsuo; Taguchi, Dai; Manaka, Takaaki; Iwamoto, Mitsumasa

2016-04-01

By using I-V, EL-V, displacement current measurement (DCM) and time-resolved electric-field-induced optical second-harmonic generation (TR-EFISHG) measurement, we studied the influence of interface pentacene layer inserted between ITO and a-NPD layers in ITO/α-NPD/Alq3/Al OLEDs. All experiments were carried out for the OLEDs with and without a pentacene interface layer. The I-V and EL-V measurements showed the decrease of operating voltage of EL, the DCM showed the lowering of inception voltage of carrier injection by inserting a pentacene interface layer. The TR-EFISHG measurement showed the faster accumulation of holes at the interface between the a-NPD and Alq3 layers, which resulted in the relaxation of electric field of a-NPD layer accomplished by the increase of the conductivity and the increase of the electric field in the Alq3 layer. We conclude that TR-EFISHG measurement is helpful for understanding I-V and EL-V characteristics, and can be combined with other methods to give significant information which are impacted by the interface layer.

Evaluation of 8-Hydroxyquinoline Derivatives as Hits for Antifungal Drug Design.

PubMed

Pippi, Bruna; Reginatto, Paula; Machado, Gabriella da Rosa Monte; Bergamo, Vanessa Zafaneli; Lana, Daiane Flores Dalla; Teixeira, Mario Lettieri; Franco, Lucas Lopardi; Alves, Ricardo José; Andrade, Saulo Fernandes; Fuentefria, Alexandre Meneghello

2017-10-01

Clioquinol is an 8-hydroxyquinoline derivative that was widely used from the 1950s to 1970s as an oral antiparasitic agent. In 1970, the oral forms were withdrawn from the market due to reports of toxicity, but topical formulations for antifungal treatment remained available. Thus, the purpose of this study was to evaluate the toxicity, anti-Candida and antidermatophyte activity and to determine pharmacodynamic characteristics of clioquinol and other 8-hydroxyquinoline derivatives (8-hydroxy-5-quinolinesulfonic acid and 8-hydroxy-7-iodo-5-quinolinesulfonic acid). Antifungal activity was tested by broth microdilution and the fungicidal or fungistatic effect was checked by a time-kill assay. Permeation and histopathological evaluation were performed in Franz diffusion cells with ear skin of pigs and examined under light microscopy. An HET-CAM test was used to determine the potential irritancy. The three compounds were active against all isolates showing anti-Candida and antidermatophyte activity, with MIC ranges of 0.031-2 μg/ml, 1-512 μg/ml, and 2-1024 μg/ml for clioquinol, 8-hydroxy-5-quinolinesulfonic acid, and 8-hydroxy-7-iodo-5-quinolinesulfonic acid, respectively. All compounds showed fungistatic effect for Candida, 8-hydroxy-5-quinolinesulfonic acid, and 8-hydroxy-7-iodo-5-quinolinesulfonic acid showed a fungicidal effect for M. canis and T. mentagrophytes, and clioquinol showed a fungicidal effect only for T. mentagrophytes. Furthermore, they presented a fungicidal effect depending on the time and concentration. The absence of lesions was observed in histopathological evaluation and no compound was irritating. Moreover, clioquinol and 8-hydroxy-5-quinolinesulfonic acid accumulated in the epithelial tissue, and 8-hydroxy-7-iodo-5-quinolinesulfonic acid had a high degree of permeation. In conclusion, 8-hydroxyquinoline derivatives showed antifungal activity and 8-hydroxy-5-quinolinesulfonic acid demonstrated the potential for antifungal drug design. © The Author 2017. Published by Oxford University Press on behalf of The International Society for Human and Animal Mycology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Absorption spectra of 4f electron transitions of neodymium and erbium with 8-hydroxyquinoline-5-sulphonic acid and diethylamine systems and its analytical application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang Naixing; Qi Ping

1992-06-01

In this paper the absorption spectra of 4f electron transitions of the systems of neodymium and erbium with 8-hydroxyquinoline-5-sulphonic acid and diethylamine have been studied by normal and third-derivative spectrophotometry. Their molar absorptivities are 80 1.mol{sup {minus}1}.cm{sup {minus}1} for neodymium and 65 1.mol{sup {minus}1}.cm{sup {minus}1} for erbium. Use of the third-derivative spectra, eliminates the interference by other rare earths and increases the sensitivity for Nd and Er. The derivative molar absorptivities are 390 1.mol{sup {minus}1}.cm{sup {minus}1} for Nd and 367 1.mol{sup {minus}1}.cm{sup {minus}1} for Er. The calibration graphs were linear up to 11.8 {mu}g/ml of Nd and 12.3 {mu}g/ml ofmore » Er, respectively. The relative standard deviations evaluated from eleven independent determinations of 7.2 {mu}g/ml (for Nd) and 8.3 {mu}g/ml (for Er) are 1.3% and 1.4%, respectively. The detection limits are 0.2 {mu}g/ml for Nd and 0.3 {mu}g/ml for Er. The method has been developed for determining those two elements in mixture of lanthanides by means of the third-derivative spectra and the analytical results obtained are satisfactory.« less

Synthesis and amino acids complexation of tripodal hexasubstituted benzene chiral receptors

NASA Astrophysics Data System (ADS)

Choksakulporn, Saowanaporn; Punkvang, Auradee; Sritana-anant, Yongsak

2015-02-01

The parent 1,3,5-triacetyl-2,4,6-trihydroxybenzene was prepared in up to 91% yield using a one-pot, one step reaction catalyzed by aluminum chloride. Its alkylations with 1,5-dibromopentane generated a symmetric tripodal hexasubstituted benzene precursor in the alternated conformer predicted by a theoretical calculation. Subsequent substitutions and reductions provided the corresponding tris-amine in 59% yield. Aminations of the tripodal precursor with (R)-(+)-1-phenylethylamine obtained a chiral tris-amine ligand in 44% yield. 1H NMR titrations of this ligand with each of three L-amino acid derivatives as guest molecules confirmed the presence of their complexes, in which the complex with alanine derivative displayed the strongest interactions with the ligand. Job plots suggested that all complexes composed of 1:2 ratios of the ligand and these guests. Theoretical calculations additionally revealed the structures and the associated binding parameters of the complexes.

Self-assembly of five 8-hydroxyquinolinate-based complexes: tunable core, supramolecular structure, and photoluminescence properties.

PubMed

Yuan, Guozan; Shan, Weilong; Qiao, Xuelong; Ma, Li; Huo, Yanping

2014-07-01

Five new Zn(II) complexes, namely [Zn(3)(L)(6)] (1), [Zn(2)(Cl)(2)(L)(2) (py)(2)] (2), [Zn(2)(Br)(2) (L)(2)(py)(2)] (3), [Zn(L)(2)(py)] (4), and [Zn(2)(OAc)(2)(L)(2)(py)(2)] (5), were prepared by the solvothermal reaction of ZnX(2) (X(-) =Cl(-), Br(-), F(-), and OAc(-)) salts with a 8-hydroxyquinolinate ligand (HL) that contained a trifluorophenyl group. All of the complexes were characterized by elemental analysis, IR spectroscopy, and powder and single-crystal X-ray crystallography. The building blocks exhibited unprecedented structural diversification and their self-assembly afforded one mononuclear, three binuclear, and one trinuclear Zn(II) structures in response to different anions and solvent systems. Complexes 1-5 featured four types of supramolecular network controlled by non-covalent interactions, such as π⋅⋅⋅π-stacking, C-H⋅⋅⋅π, hydrogen-bonding, and halogen-related interactions. Investigation of their photoluminescence properties exhibited disparate emission wavelengths, lifetimes, and quantum yields in the solid state. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

In Vitro Selective Growth-Inhibitory Effect of 8-Hydroxyquinoline on Clostridium perfringens versus Bifidobacteria in a Medium Containing Chicken Ileal Digesta.

PubMed

Skrivanova, Eva; Van Immerseel, Filip; Hovorkova, Petra; Kokoska, Ladislav

2016-01-01

Clostridium perfringens-induced necrotic enteritis is generally controlled by antibiotics. However, because of increasing antibiotic resistance, other antibacterial agents are required, preferably ones that do not affect the beneficial intestinal microbiota of the host. This study evaluated the in vitro selective growth-inhibitory effect of 8-hydroxyquinoline (8HQ) on C. perfringens vs. bifidobacteria in a medium containing chicken ileal digesta. Prior to the experiments, the minimum inhibitory concentrations of 8HQ and penicillin G were determined by broth microdilution assay. The minimum inhibitory concentration values of 8HQ for C. perfringens were 16-32 times lower than the values for bifidobacteria. Treatment of autoclaved and non-autoclaved chicken ileal digesta with 8HQ showed a selective anticlostridial effect. After incubation of C. perfringens with autoclaved ileal digesta for 3 h, all 8HQ concentrations tested (32-2048 μg/mL) significantly reduced C. perfringens bacterial count. In contrast, the same treatment had no or only a slight effect on bifidobacteria counts. Unlike 8HQ, penicillin G did not exhibit any selectivity. Similar results were obtained after incubation for 24 h. In non-autoclaved ileal digesta, all 8HQ concentrations tested significantly reduced C. perfringens bacterial counts after incubation for 30 min and 3 h, while no effect was observed on bifidobacteria. These results suggest that 8HQ may serve as a prospective veterinary compound for use against necrotic enteritis in poultry.

Study of structural and optical properties of ZnAlQ5 (zinc aluminum quinolate) organic phosphor for OLED applications

NASA Astrophysics Data System (ADS)

Nagpure, I. M.; Painuly, Deepshikha; Rabanal, Maria Eugenia

2016-05-01

The various composition of ZnAlQ5 such as Zn1.5A10.5Q5, Zn1Al1Q5, Zn0.5Al1.5Q5 organic phosphors were prepared via simple cost effective co-precipitation method. The FTIR, SEM, photoluminescence analysis of the prepared phosphors were reported. ZnQ2 and AlQ3 were also prepared by similar method and their properties were compared with different composition of ZnAlQ5. The structural elucidation in the form of stretching frequencies of chemical bonds of the prepared phosphor was carried out using Fourier Transform Infrared Spectroscopy (FTIR). The stretching frequency analysis confirms the formation of prepared phosphor materials. The SEM analysis shows the surface morphological behavior of prepared phosphor materials. Greenish photoluminescence were observed at 505 to 510 nm for the different composition of ZnAlQ5,in which Zn1.5Al0.5Q5 shows maximum luminescence intensity at 505 nm. PL emission of ZnQ2 was observed at 515 nm, while for AlQ3 at 520 nm. The blue shift of 10 nm was observed in Zn1.5A10.5Q5 due to modification of energy level due to presence of Zn2+ and Al3+. The enhancement in PL intensity was observed in Zn1.5A10.5Q5 compared to the other composition due to transfer of energy between Zn2+ and quinolate complex. Optical properties of the prepared materials were evaluated for possible applications in organic light emitting devices (OLED).

Xenobiotics enhance laccase activity in alkali-tolerant γ-proteobacterium JB.

PubMed

Singh, Gursharan; Batish, Mona; Sharma, Prince; Capalash, Neena

2009-01-01

Various genotoxic textile dyes, xenobiotics, substrates (10 µM) and agrochemicals (100 µg/ml) were tested for enhancement of alkalophilic laccase activity in γ-proteobacterium JB. Neutral Red, Indigo Carmine, Naphthol Base Bordears and Sulphast Ruby dyes increased the activity by 3.7, 2.7, 2.6 and 2.3 fold respectively. Xenobiotics/substrates like p-toluidine, 8-hydroxyquinoline and anthracine increased it by 3.4, 2.8 and 2.3 fold respectively. Atrazine and trycyclozole pesticides enhanced the activity by 1.95 and 1.5 fold respectively.

Xenobiotics enhance laccase activity in alkali-tolerant γ-proteobacterium JB

PubMed Central

Singh, Gursharan; Batish, Mona; Sharma, Prince; Capalash, Neena

2009-01-01

Various genotoxic textile dyes, xenobiotics, substrates (10 µM) and agrochemicals (100 µg/ml) were tested for enhancement of alkalophilic laccase activity in γ-proteobacterium JB. Neutral Red, Indigo Carmine, Naphthol Base Bordears and Sulphast Ruby dyes increased the activity by 3.7, 2.7, 2.6 and 2.3 fold respectively. Xenobiotics/substrates like p-toluidine, 8-hydroxyquinoline and anthracine increased it by 3.4, 2.8 and 2.3 fold respectively. Atrazine and trycyclozole pesticides enhanced the activity by 1.95 and 1.5 fold respectively. PMID:24031313

8-hydroxyquinoline inhibition of DNA synthesis and intragenic recombination during yeast meiosis.

PubMed

Mills, D

1978-06-14

Complete inhibition of sporulation was observed in two strains of Saccharomyces cerevisiae to which 8-hydroxyquinoline was added at a final concentration of 5 microgram/ml during the initial 4 to 6 h of sporulation. The cells were most sensitive to the inhibitor during 4 to 6 interval beginning at approximately 2 h (T2). Its addition during that interval resulted in 70 to 80% lethality in strain 4579 and about 40% in API at T24. When present from T0 onward, 5 microgram/ml of 8-hydroxyquinoline severely inhibited premeiotic DNA replication and reduced the frequency of intragenic recombination at the ade 2 and leu 2 loci by 70 and 100%, respectively, relative to control cultures which did not have the inhibitor present. During the period when the cells were most sensitive, the incorporation of 14C-leucine into protein and 14C-adenine into RNA was not inhibited nor was the polysome content affected. At 150 microgram/ml of inhibitor, incorporation of labeled precursors into RNA and protein were inhibited and the percentage of active ribosomes was reduced by 35% within 45 min, but neither transcription or translation appeared to be completely inhibited at this concentration of the inhibitor.

Partial purification and some properties of a latent CO2 reductase from green potato tuber chloroplasts.

PubMed

Arora, S; Ramaswamy, N K; Nair, P M

1985-12-16

We have partially purified the CO2 reductase, present in green potato tuber chloroplasts, as a latent form. Illumination of the chloroplasts in the absence of substrate, bicarbonate, activated the enzyme, which could then be obtained in soluble forms. Purification of the enzyme was achieved by (NH4)2SO4 fractionation (0-30%) and adsorption and elution from a DEAE-Sephadex A-50 column. The final preparation showed 15-fold purification and 50% recovery of the activity. The pH optimum for CO2 reductase was 8.0. Hepes and Tricine buffers showed maximum activity whereas Tris/phosphate or borate failed to show any activity. The enzyme reaction was sensitive to the presence of metal ions like Fe3+, Hg2+, Cu2+, Mo6+ and Zn2+, however, a threefold activation was observed with Fe2+. The metal requirement for CO2 reductase was evident from the observed inhibition by metal chelators like o-phenanthroline, alpha, alpha'-dipyridyl, bathocuproine, 8-hydroxyquinoline etc. Out of these o-phenanthroline was the strongest inhibitor and its concentration for 50% inhibition was 40 microM. The presence of Fe2+ ions in the reaction mixture protected the enzyme from heat denaturation upto 50 degrees C. Maximum enzyme activity was observed at 15 degrees C. The enzyme activity showed a 30-s lag period and the maximum was reached in 90 s. Supplementation of sodium dithionite in the reaction activated enzyme activity threefold, suggesting involvement of dithiol groups in the catalytic activity. There was strong inhibition by -SH inhibitors like 5,5'-dithiobis(2-nitrobenzoic acid) and N-ethylmaleimide and -SH reagents like dithiothreitol, 2-mercaptoethanol and cysteine. Various nucleotide coenzyme tried inhibited the enzyme strongly.

Encapsulation of anticancer drug copper bis(8-hydroxyquinoline) in hydroxyapatite for pH-sensitive targeted delivery and slow release.

PubMed

Weerasuriya, D R K; Wijesinghe, W P S L; Rajapakse, R M G

2017-02-01

There is a conspicuous progress in increasing anticancer drug delivery through the utilization of nanoparticles (NPs) as drug delivery agents. Hydroxyapatite (HA) gives improved clinical effectiveness of drugs by reducing systemic toxicity and broadening the spectrum of drug delivery since it is biocompatible and it can be targeted towards tumor cells. Herein, investigation of the potential of enhancing controlled drug release of the template model drug, copper bis-(8-hydroxyquinoline), by encapsulating it in hollow hydroxyapatite nano-carriers, is presented. Hydroxyapatite nanoparticles are synthesized by following four different routes to optimize its efficacy of drug loading. Copper bis-(8-hydroxyquinoline) is encapsulated by Method (a) which was effected by stirring the model drug and porous HA NPs in colloidal solution and Method (b) which was done during synthesis of hydroxyapatite nanoparticles in a solution of the model drug. In synthesizing nanoporous HA NPs, calcium carbonate is used as a template to create voids in HA. In each method, Ca/P ratio was ensured to be kept at 1.67:1. Appealing results are reported for the encapsulated product which was prepared by Method (a2). Method (a) was done at three different molar ratios of PO 4 3- :CO 3 2- and best result was obtained for that utilized 2.003:1 molar ratio (Method (a2).). It produced 98.67% of encapsulation efficiency and 2.9522mg/g of drug loading capacity. Release kinetics was studied at a range of pH values; the lower the pH of the medium the higher is the drug release. For instance, when considering the product which exhibited high encapsulation efficiency and high drug loading capacity, at pH3.5 during the first 8h it elicited about 13% of release, at pH5.0 about 8% release while at pH6.0 it was just 2.5%. During the 24-hour span, pH3.5 exhibited about 23.8%, at pH5.0 approximately 9% with an increasing trend of release and at pH6.0 showed a value just above 2.5%. As such, acidity of the cancerous cells can be made use to increase the drug slow-release kinetics at the vicinity of the cancer cells. Copyright © 2016 Elsevier B.V. All rights reserved.

Direct excitation luminescence spectroscopy of Eu(III) complexes of 1,4,7-tris(carbamoylmethyl)-1,4,7,10- tetraazacyclododecane derivatives and kinetic studies of their catalytic cleavage of an RNA analog.

PubMed

Nwe, Kido; Richard, John P; Morrow, Janet R

2007-11-28

The macrocycles 1,4,7-tris(carbamoylmethyl)-1,4,7,10-tetrazacyclododecane (1), 1,4,7-tris[(N-ethyl)carbamoylmethyl]-1,4,7,10-tetraazacyclododecane (2), 1,4,7-tris[(N,N-diethyl)carbamoylmethyl]-1,4,7,10-tetraazacyclododecane (3) and their Eu(III) complexes are prepared. Studies using direct Eu(III) excitation luminescence spectroscopy show that all three Eu(III) complexes exhibit only one predominant isomer with two bound waters under neutral to mildly basic conditions (Eu(X)(H(2)O)(2) for X = 1-3). There are no detectable ligand ionizations over the pH range 5.0-8.0 for Eu(3), 5.0-8.5 for Eu(2) or 5.0-9.5 for Eu(1). The three Eu(III) complexes show a linear dependence of second-order rate constants for the cleavage of 4-nitrophenyl-2-hydroxyethylphosphate (HpPNP) on pH in the range 6.5-8.0 for Eu(3), 7.0-8.5 for Eu(2) and 7.0-9.0 for Eu(1). This pH-rate profile is consistent with the Eu(III) complex-substrate complex being converted to the active form by loss of a proton and with Eu(III) water pK(a) values that are higher than 8.0 for Eu(3), 8.5 for Eu(2) and 9.0 for Eu(1). Inhibition studies show that Eu() binds strongly to the dianionic ligand methylphosphate (K(d) = 0.28 mM), and more weakly to diethylphosphate (K(d) = 7.5 mM), consistent with a catalytic role of the Eu(III) complexes in stabilizing the developing negative charge on the phosphorane transition state.

Time-resolved EPR study on the photoexcited triplet state of the electron-donor-acceptor complex formed in the system of fac-tris[2-(4-octyl-phenyl) pyridine] iridium(III) and tetracene.

PubMed

Zhebin, Fu; Shuhei, Yoshioka; Hisao, Murai

2014-01-09

The physical properties of the phosphorescent organic light-emitting diode material fac-tris(phenylpyridine) iridium(III), Ir(ppy)3, have been reported with experimental and theoretical studies. Here, the photochemical properties of the excited triplet state of partially modified fac-tris[2-(4-octyl-phenyl) pyridine] iridium(III), Ir(C8ppy)3, were investigated using time-resolved electron paramagnetic resonance (tr-EPR) and optical methods by adding tetracene in the toluene solution. The tr-EPR observation at 77 K revealed the following two species: the excited triplet state of tetracene and another triplet species with zero field splitting parameters of |D| = 0.088 cm(-1) and |E| = 0.018 cm(-1) with characteristic spin polarization. The latter species was assigned to the electron-donor-acceptor (EDA) complex formed between Ir(C8ppy)3 and tetracene. The mechanism of formation and the properties of this EDA complex, including the information on the principal axes of (3)Ir(C8ppy)3*, are discussed.

Nanowires of metal (Cd, Cu) halide complexes with 8-hydroxyquinoline for photoelectrochemical and electrochemiluminescence sensing

NASA Astrophysics Data System (ADS)

Huang, Shan; Pang, Guangming; Li, Xiangkui; Li, Jianping; Pan, Hongcheng

2017-12-01

Metal-hydroxyquinoline-halogen (MqX, M = Cd, Cu; q = 8-hydroxyquinoline; X = Cl, Br, I) nanowires are synthesized via a sonochemical-assisted method. The elemental analysis (EA), inductively coupled plasma-optical emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS) support an M/q/X ratio of 1:1:1. The electron microscope images reveal a typical CdqX and CuqX nanowire diameter of 30-50 nm and a nanowire length of 400-600 nm. In addition, the synthesis of the MqX nanowires is only observed when there is an excess of halide ions (X/q molar ratio of 3 or greater). This halide deficiency results in the formation of micrometer-sized Mq2 sheets. We demonstrated the conversion of the MqX nanowires to Mq2 micro-sheets in an ultrasonic bath of 1 M 8-Hq ethanol solutions (50%, w/ w) at 50 °C for 2 h, but not vice versa. The MqX nanowires exhibited excellent properties for photoluminescence, electrochemiluminescence (ECL), and photoelectrochemistry (PEC). The CdqBr and CdqI nanowires were coated onto a glass carbon and a fluorine-doped tin oxide glass electrode to develop the above ECL and PEC methods for the detection of H2O2 and Cu2+, respectively. In the range of 2 to 14 μM, the ECL intensity of the CdqBr nanowires was inversely proportional to the concentration of H2O2 with a detection limit of 0.26 μM. For Cu2+ sensing, the photocurrent of the CdqI nanowires exhibited a linear response to Cu2+ over the range of 2 to 16 μM of which a detection limit of 0.2 μM was observed.

DNA adsorption onto glass surfaces

NASA Astrophysics Data System (ADS)

Carlson, Krista Lynn

Streaming potential measurements were performed on microspheres of silica, lime silicate (SLS) and calcium aluminate (CA) glasses containing silica and iron oxide (CASi and CAFe). The silicate based glasses exhibited acidic surfaces with isoelectric points (IEP) around a pH of 3 while the calcium aluminates displayed more basic surfaces with IEP ranging from 8--9.5. The surface of the calcium aluminate microspheres containing silica reacted with the background electrolyte, altering the measured zeta potential values and inhibiting electrolyte flow past the sample at ˜ pH 4 due to formation of a solid plug. DNA adsorption experiments were performed using the microspheres and a commercially available silicate based DNA isolation filter using a known quantity of DNA suspended in a chaotropic agent free 0.35 wt% Tris(hydroxymethyl)aminomethane (Tris) buffer solution. The microspheres and commercial filter were also used to isolate DNA from macrophage cells in the presence of chaotropic agents. UV absorbance at ˜260 nm and gel electrophoresis were used to quantify the amount and size of the DNA strands that adsorbed to the microsphere surfaces. In both experiments, the 43--106 microm CAFe microspheres adsorbed the largest quantity of DNA. However, the 43--106 microm SLS microspheres isolated more DNA from the cells than the <43 microm CAFe microspheres, indicating that microsphere size contributes to isolation ability. The UV absorbance of DNA at ˜260 nm was slightly altered due to the dissolution of the calcium aluminate glasses during the adsorption process. Inductively coupled plasma-optical emission spectroscopy (ICP-OES) determined that calcium and aluminum ions leached from the CA and CAFe microsphere surfaces during these experiments. Circular dichroism (CD) spectroscopy showed that the leached ions had no effect on the conformation of the DNA, and therefore would not be expected to interfere in downstream applications such as DNA replication. The 0.35 wt% Tris solution completely inhibited the formation of the hydrated crystalline layer that develops when the calcium aluminate glassess are incubated in deionized water. A Tris concentration of 0.24 wt% allowed for the formation of both hexagonal and cubic hydrates, however they were severely distorted and present in low amounts such that they were undectable by XRD.

Sticker-type Alq(3)-based OLEDs based on printable ultrathin substrates in periodically anchored and suspended configurations.

PubMed

Yun, Su Ok; Hwang, Youngkyu; Park, Jeongpil; Jeong, Yunkyung; Kim, Suk Ho; Noh, Byeong Il; Jung, Hoon Sun; Jang, Hun Soo; Hyun, Yujun; Choa, Sung-Hoon; Ko, Heung Cho

2013-10-18

Introducing two-dimensional post arrays and a water-soluble sacrificial layer between an ultrathin substrate and a handling substrate provides controllability of the interfacial adhesion in a stable manner. The periodically anchored and suspended configuration after the chemical etching process facilitates the development of, for example, printable Alq3 -based OLEDs that can be attached to unconventional surfaces. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Direct determination of energy level alignment and charge transport at metal-Alq3 interfaces via ballistic-electron-emission spectroscopy.

PubMed

Jiang, J S; Pearson, J E; Bader, S D

2011-04-15

Using ballistic-electron-emission spectroscopy (BEES), we directly determined the energy barrier for electron injection at clean interfaces of Alq(3) with Al and Fe to be 2.1 and 2.2 eV, respectively. We quantitatively modeled the sub-barrier BEES spectra with an accumulated space charge layer, and found that the transport of nonballistic electrons is consistent with random hopping over the injection barrier.

Direct determination of energy level alignment and charge transport at metal/Alq{sub 3} interfaces via ballistic-electron-emission spectroscopy.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, J. S.; Pearson, J. E.; Bader, S. D.

2011-04-15

Using ballistic-electron-emission spectroscopy (BEES), we directly determined the energy barrier for electron injection at clean interfaces of Alq{sub 3} with Al and Fe to be 2.1 and 2.2 eV, respectively. We quantitatively modeled the sub-barrier BEES spectra with an accumulated space charge layer, and found that the transport of nonballistic electrons is consistent with random hopping over the injection barrier.

Experimental and theoretical studies of structural and photophysical properties of a novel heteroleptic cyclometalated iridium(III) complex with 8-hydroxyquinoline-phenylazo ligand

NASA Astrophysics Data System (ADS)

Maity, Amit; Sinha, Debopam; Rajak, Kajal Krishna

2018-04-01

One novel heteroleptic iridium(III) complex with cyclometalated 2-phenylquinoline(2-phq) was synthesized by the stoichiometric reaction of [Ir(2-phq)2Cl]2, i.e, Bis-[μ-chlorodi-(2-phenylquinoline)iridium(III)] and HL ligand, where L- is deprotonated form of azo ligand prepared from 8-hydroxyquinoline and aniline in a 1:1 proportion of dichloromethane and ethanol solvent at argon atmosphere in presence of mild base triethylamine in stoichiometric ratio. The prepared complex was characterized by 1H NMR, ESI-mass spectrometry, IR spectroscopy and most accurately by X-ray single crystallography. The photo physical properties like absorption and emission, i.e, photoluminescence in liquid state as well as solid state were studied exclusively. The experimental electrochemical study was also done with cyclic voltammetry. The theoretical investigations of the photo physical properties were done by DFT and TDDFT calculations. The ground state excitation transitions of the complex arise from 1ILCT and 1MLCT transition. The UV-Vis and photoluminescence transition was also investigated by NTO analysis. The triplet state emission transition was characterized by 3MLCT and some portion of 3ILCT transition.

Fertility test of frozen boar semen.

PubMed

Osinowa, O; Salamon, S

1976-10-01

The fertility results of two experiments are presented. In experiment 1, the semen was frozen in tris-fructose-EDTA or BF3 diluents at 0-25 X 10(9)/ml sperm concentration and extended after thawing with either seminal plasma (SP) or the freezing medium (FM) containing no cryoprotective agent. In the second experiment the semen was glycerolated by two methods, frozen at 1-0 X 10(9)/ml sperm concentration, and extended wtih FM before insemination. Fertility after double insemination within one oestrus with semen frozen in tris-fructose-EDTA or BF3 diluents varied depending on the medium used for extension of thawed semen. The farrowing rates for semen frozen in the former diluent with FM and SP post-thawing media were 4/8 and 1/8 respectively, and for semen frozen BF3 diluent with FM and SP post-thawing extenders 1/8 and 5/8. The mean farrowing for the 32 animals inseminasted was 34-4%. Pregnancies for semen frozen in tris-fructose-EDTA and glycerolated at 30 or 5 degrees C were 5/12 and 4/12 respectively, and for single and double inseminations 6/12 and 3/12 respectively. Of 24 animals inseminated 37-5% farrowed.

Preparation of 8-hydroxyquinoline derivatives as potential antibiotics against Staphylococcus aureus.

PubMed

Lam, Kim-Hung; Gambari, Roberto; Lee, Kenneth Ka-Ho; Chen, Yi-Xin; Kok, Stanton Hon-Lung; Wong, Raymond Siu-Ming; Lau, Fung-Yi; Cheng, Chor-Hing; Wong, Wai-Yeung; Bian, Zhao-Xiang; Chan, Albert Sun-Chi; Tang, Johnny Cheuk-On; Chui, Chung-Hin

2014-01-01

This work describes the preparation of quinoline compounds as possible anti-bacterial agents. The synthesized quinoline derivatives show anti-bacterial activity towards Staphylococcus aureus. It is interesting to observe that the synthetic 5,7-dibromo-2-methylquinolin-8-ol (4) shows a similar minimum inhibitory concentration of 6.25μg/mL as compared to that of methicillin (3.125μg/mL) against Staphylococcus aureus. Copyright © 2013 Elsevier Ltd. All rights reserved.

75 FR 44184 - Aluminum tris(O-ethylphosphonate), Butylate, Chlorethoxyfos, Clethodim, et al.; Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-28

...: Crop production (NAICS code 111). Animal production (NAICS code 112). Food manufacturing (NAICS code... contamination of food, feed, or food-contact/feed-contact surfaces. Compliance with the tolerance level... Apply to Me? You may be potentially affected by this action if you are an agricultural producer, food...

Development of 8-hydroxyquinoline metal based organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Feng, Xiaodong

Because of its potential application for flat panel displays, solid-state lighting and 1.5 mum emitter for fiber optical communications, organic light-emitting diodes (OLEDs) have been intensively researched. One of the major problems with current OLED technology relates to inefficient electron injection at the cathode interface, which causes high driving voltage and poor device stability. Making a low resistance cathode contact for electron injection is critical to device performance. This work mainly focuses on cathode interface design and engineering. The Ohmic contact using a structure of C60/LiF/Al has been developed in electron only devices. It is found that application of the C60/LiF/Al contact to Alq based OLEDs leads to a dramatic reduction in driving voltages, a significant improvement in power efficiency, and a much slower aging process. A new cathode structure based on metal-organic-metal (MOM) tri-layer films has been developed. It is found that MOM cathodes reduce reflection by deconstructive optical interference from two metal films. The absolute reflectance from the MOM tr-ilayer films can be reduced to as low as 7% in the visible light spectrum. In actual working devices, the reflectance can be reduced from ˜80% to ˜20%. MOM cathodes provide a potential low-cost solution for high contrast full-color OLED displays. Low voltage Erq based OLEDs at 1.5 mum emission have been developed. The Erq/Ag cathode interface has been found to be efficient for electron injection. Dramatic improvement in driving voltage and power efficiency has been realized by implementing Bphen and C60 into Erq devices as an electron transport layer. Integration of Erq devices on Si wafers has also been demonstrated.

8-Hydroxyquinolines Are Boosting Agents of Copper-Related Toxicity in Mycobacterium tuberculosis.

PubMed

Shah, Santosh; Dalecki, Alex G; Malalasekera, Aruni P; Crawford, Cameron L; Michalek, Suzanne M; Kutsch, Olaf; Sun, Jim; Bossmann, Stefan H; Wolschendorf, Frank

2016-10-01

Copper (Cu) ions are likely the most important immunological metal-related toxin utilized in controlling bacterial infections. Impairment of bacterial Cu resistance reduces viability within the host. Thus, pharmacological enhancement of Cu-mediated antibacterial toxicity may lead to novel strategies in drug discovery and development. Screening for Cu toxicity-enhancing antibacterial molecules identified 8-hydroxyquinoline (8HQ) to be a potent Cu-dependent bactericidal inhibitor of Mycobacterium tuberculosis The MIC of 8HQ in the presence of Cu was 0.16 μM for replicating and nonreplicating M. tuberculosis cells. We found 8HQ's activity to be dependent on the presence of extracellular Cu and to be related to an increase in cell-associated labile Cu ions. Both findings are consistent with 8HQ acting as a Cu ionophore. Accordingly, we identified the 1:1 complex of 8HQ and Cu to be its active form, with Zn, Fe, or Mn neither enhancing nor reducing its Cu-specific action. This is remarkable, considering that the respective metal complexes have nearly identical structures and geometries. Finally, we found 8HQ to kill M. tuberculosis selectively within infected primary macrophages. Given the stark Cu-dependent nature of 8HQ activity, this is the first piece of evidence that Cu ions within macrophages may bestow antibacterial properties to a Cu-dependent inhibitor of M. tuberculosis In conclusion, our findings highlight the metal-binding ability of the 8-hydroxyquinoline scaffold to be a potential focus for future medicinal chemistry and highlight the potential of innate immunity-inspired screening platforms to reveal molecules with novel modes of action against M. tuberculosis. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Optical parameters of ITO/TPD/Alq3/Al luminescent structures, containing arrays of CdSe/ZnS colloidal quantum dots

NASA Astrophysics Data System (ADS)

Mikhailov, I. I.; Tarasov, S. A.; Lamkin, I. A.; Tadtaev, P. O.; Kozlovich, L. I.; Solomonov, A. V.; Stepanov, E. M.

2016-08-01

The luminescent organic ITO/TPD/Alq3/Al structures and CdSe/ZnS quantum dots (QD) arrays were created. Electrical and optical properties of the samples were examined. The luminescence of the layers and QD arrays was shown in the range of wavelengths from 400 to 680 nm. Luminescent structures with phosphors corresponding to the emission standards with CRI>98 and with color temperature of 5500 K and 6504 K were created.

Efficient extraction of vaccines formulated in aluminum hydroxide gel by including surfactants in the extraction buffer

PubMed Central

Zhu, Daming; Huang, Shuhui; McClellan, Holly; Dai, Weili; Syed, Najam R; Gebregeorgis, Elizabeth; Mullen, Gregory E. D.; Long, Carole; Martin, Laura B.; Narum, David; Duffy, Patrick; Miller, Louis H.; Saul, Allan

2011-01-01

Efficient antigen extraction from vaccines formulated on aluminum hydroxide gels is a critical step for the evaluation of the quality of vaccines following formulation. It has been shown in our laboratory that the efficiency of antigen extraction from vaccines formulated on Alhydrogel decreased significantly with increased storage time. To increase antigen extraction efficiency, the present study determined the effect of surfactants on antigen recovery from vaccine formulations. The Plasmodium falciparum apical membrane antigen 1 (AMA1) formulated on Alhydrogel and stored at 2-8 °C for three years was used as a model in this study. The AMA1 on Alhydrogel was extracted in the presence or absence of 30 mM sodium dodecyl sulfate (SDS) or 20 mM cetylpyridinium chloride in the extraction buffer (0.60 M citrate, 0.55 M phosphate, pH 8.5) using our standard antigen extraction protocols. Extracted AMA1 antigen was analyzed by 4-20% Tris-glycine SDS-PAGE followed by silver staining or western blotting. The results showed that inclusion of SDS or cetylpyridinium chloride in extraction buffer increased the antigen recovery dramatically and can be used for efficient characterization of Alhydrogel vaccines. PMID:22107848

Plutonium Extraction by the Formation of Insoluble Salts; EXTRACTION DU PLUTONIUM PAR FORMATION DE SELS INSOLUBLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ganivet, M.

1960-06-29

The aim of this work is to convert Pu IV nitrate in solution into an insoluble salt. Three methods have been studied: 1) the conventional oxalic acid method was improved; 2) precipitation with 8-hydroxyquinoline was tried; 3) the hydrogen peroxide method was adapted to the eluates of the ionic resins from Marcoule. The yield from the oxalic process has been increased (loss of Pu in the mother-liquor brought from 200 mg/l to 20 mg/l). The study of Pu IV precipitation by 8-hydroxyquinoline has shown that the yield is excellent (Pu concentration in the mother-liquor less than 5 mg/h), but decontaminationmore » from impurities is nil. Finally, experiments on the precipitation by hydrogen peroxide of Pu IV solutions at the concentrations normally obtained from the anionic resins at Marcoule have given us good yields (Pu concentration in the mother-liquor less than 7 mg/l), and the purification is better than that obtained by oxalic acid (1000 ppm total impurities after a precipitation). (author)« less

Effect of Li2O/Al cathode in Alq3 based organic light-emitting diodes.

PubMed

Shin, Eun Chul; Ahn, Hui Chul; Han, Wone Keun; Kim, Tae Wan; Lee, Won Jae; Hong, Jin Woong; Chung, Dong Hoe; Song, Min Jong

2008-09-01

An effect of bilayer cathode Li20/Al was studied in Alq3 based organic light-emitting diodes with a variation of Li2O layer thickness. The current-luminance-voltage characteristics of ITO/TPD/Alq3/Li2O/Al device were measured at ambient condition to investigate the effect of Li2O/Al. It was found that when the thickness of Li2O layer is in the range of 0.5-1 nm, there are improvements in luminance, efficiency, and turn-on voltage of the device. A current density and a luminance are increased by about 100 times, a turn-on voltage is lowered from 6 V to 3 V, a maximum current efficiency is improved by a factor of 2.3, and a maximum power efficiency is improved by a factor of 3.2 for a device with a use of thin Li2O layer compared to those of the one without the Li2Otron-barrier height for electron injection from the cathode to the emissive layer.

A matrix-focused structure-activity and binding site flexibility study of quinolinol inhibitors of botulinum neurotoxin serotype A.

PubMed

Harrell, William A; Vieira, Rebecca C; Ensel, Susan M; Montgomery, Vicki; Guernieri, Rebecca; Eccard, Vanessa S; Campbell, Yvette; Roxas-Duncan, Virginia; Cardellina, John H; Webb, Robert P; Smith, Leonard A

2017-02-01

Our initial discovery of 8-hydroxyquinoline inhibitors of BoNT/A and separation/testing of enantiomers of one of the more active leads indicated considerable flexibility in the binding site. We designed a limited study to investigate this flexibility and probe structure-activity relationships; utilizing the Betti reaction, a 36 compound matrix of quinolinol BoNT/A LC inhibitors was developed using three 8-hydroxyquinolines, three heteroaromatic amines, and four substituted benzaldehydes. This study has revealed some of the most effective quinolinol-based BoNT/A inhibitors to date, with 7 compounds displaying IC 50 values ⩽1μM and 11 effective at ⩽2μM in an ex vivo assay. Published by Elsevier Ltd.

First-principles method for calculating the rate constants of internal-conversion and intersystem-crossing transitions.

PubMed

Valiev, R R; Cherepanov, V N; Baryshnikov, G V; Sundholm, D

2018-02-28

A method for calculating the rate constants for internal-conversion (k IC ) and intersystem-crossing (k ISC ) processes within the adiabatic and Franck-Condon (FC) approximations is proposed. The applicability of the method is demonstrated by calculation of k IC and k ISC for a set of organic and organometallic compounds with experimentally known spectroscopic properties. The studied molecules were pyrromethene-567 dye, psoralene, hetero[8]circulenes, free-base porphyrin, naphthalene, and larger polyacenes. We also studied fac-Alq 3 and fac-Ir(ppy) 3 , which are important molecules in organic light emitting diodes (OLEDs). The excitation energies were calculated at the multi-configuration quasi-degenerate second-order perturbation theory (XMC-QDPT2) level, which is found to yield excitation energies in good agreement with experimental data. Spin-orbit coupling matrix elements, non-adiabatic coupling matrix elements, Huang-Rhys factors, and vibrational energies were calculated at the time-dependent density functional theory (TDDFT) and complete active space self-consistent field (CASSCF) levels. The computed fluorescence quantum yields for the pyrromethene-567 dye, psoralene, hetero[8]circulenes, fac-Alq 3 and fac-Ir(ppy) 3 agree well with experimental data, whereas for the free-base porphyrin, naphthalene, and the polyacenes, the obtained quantum yields significantly differ from the experimental values, because the FC and adiabatic approximations are not accurate for these molecules.

Twinned low-temperature structures of tris(ethylenediamine)zinc(II) sulfate and tris(ethylenediamine)copper(II) sulfate.

PubMed

Lutz, Martin

2010-11-01

Tris(ethylenediamine)zinc(II) sulfate, [Zn(C(2)H(8)N(2))(3)]SO(4), (I), undergoes a reversible solid-solid phase transition during cooling, accompanied by a lowering of the symmetry from high-trigonal P31c to low-trigonal P3 and by merohedral twinning. The molecular symmetries of the cation and anion change from 32 (D(3)) to 3 (C(3)). This lower symmetry allows an ordered sulfate anion and generates in the complex cation two independent N atoms with significantly different geometries. The twinning is the same as in the corresponding Ni complex [Jameson et al. (1982). Acta Cryst. B38, 3016-3020]. The low-temperature phase of tris(ethylenediamine)copper(II) sulfate, [Cu(C(2)H(8)N(2))(3)]SO(4), (II), has only triclinic symmetry and the unit-cell volume is doubled with respect to the room-temperature structure in P31c. (II) was refined as a nonmerohedral twin with five twin domains. The asymmetric unit contains two independent formula units, and all cations and anions are located on general positions with 1 (C(1)) symmetry. Both molecules of the Cu complex are in elongated octahedral geometries because of the Jahn-Teller effect. This is in contrast to an earlier publication, which describes the complex as a compressed octahedron [Bertini et al. (1979). J. Chem. Soc. Dalton Trans. pp. 1409-1414].

Effects of pure plant secondary metabolites on methane production, rumen fermentation and rumen bacteria populations in vitro.

PubMed

Joch, M; Mrázek, J; Skřivanová, E; Čermák, L; Marounek, M

2018-04-29

In this study, the effects of seven pure plant secondary metabolites (PSMs) on rumen fermentation, methane (CH 4 ) production and rumen bacterial community composition were determined. Two in vitro trials were conducted. In trial 1, nine concentrations of 8-hydroxyquinoline, α-terpineol, camphor, bornyl acetate, α-pinene, thymoquinone and thymol were incubated on separate days using in vitro 24-hr batch incubations. All compounds tested demonstrated the ability to alter rumen fermentation parameters and decrease CH 4 production. However, effective concentrations differed among individual PSMs. The lowest concentrations that reduced (p < .05) CH 4 production were as follows: 8 mg/L of 8-hydroxyquinoline, 120 mg/L of thymoquinone, 240 mg/L of thymol and 480 mg/L of α-terpineol, camphor, bornyl acetate and α-pinene. These concentrations were selected for use in trial 2. In trial 2, PSMs were incubated in one run. Methane was decreased (p < .05) by all PSMs at selected concentrations. However, only 8-hydroxyquinoline, bornyl acetate and thymoquinone decreased (p < .05) CH 4 relative to volatile fatty acids (VFAs). Based on denaturing gradient gel electrophoresis analysis, different PSMs changed the composition of bacterial communities to different extents. As revealed by Ion Torrent sequencing, the effects of PSMs on relative abundance were most pronounced in the predominant families, especially in Lachnospiraceae, Succinivibrionaceae, Prevotellaceae, unclassified Clostridiales and Ruminococcaceae. The CH 4 production was correlated negatively (-.72; p < .05) with relative abundance of Succinivibrionaceae and positively with relative abundance of Ruminococcaceae (.86; p < .05). In summary, this study identified three pure PSMs (8hydroxyquinoline, bornyl acetate and thymoquinone) with potentially promising effects on rumen CH 4 production. The PSMs tested in this study demonstrated considerable impact on rumen bacterial communities even at the lowest concentrations that decreased CH 4 production. The findings from this study may help to elucidate how PSMs affect rumen bacterial fermentation. © 2018 Blackwell Verlag GmbH.

Visible and NIR photoluminescence properties of a series of novel lanthanide-organic coordination polymers based on hydroxyquinoline-carboxylate ligands.

PubMed

Gai, Yan-Li; Xiong, Ke-Cai; Chen, Lian; Bu, Yang; Li, Xing-Jun; Jiang, Fei-Long; Hong, Mao-Chun

2012-12-17

A series of novel two-dimensional (2D) lanthanide coordination polymers with 4-hydroxyquinoline-2-carboxylate (H(2)hqc) ligands, [Ln(Hhqc)(3)(H(2)O)](n)·3nH(2)O (Ln = Eu (1), Tb (2), Sm (3), Nd (4), and Gd (5)) and [Ln(Hhqc)(ox)(H(2)O)(2)](n) (Ln = Eu (6), Tb (7), Sm (8), Tm (9), Dy (10), Nd (11), Yb (12), and Gd (13); H(2)ox = oxalic acid), have been synthesized under hydrothermal conditions. Complexes 1-5 are isomorphous, which can be described as a two-dimensional (2D) hxl/Shubnikov network based on Ln(2)(CO(2))(4) paddle-wheel units, and the isomorphous complexes 6-13 feature a 2D decker layer architecture constructed by Ln-ox infinite chains cross-linked alternatively by bridging Hhqc(-) ligands. The room-temperature photoluminescence spectra of complexes Eu(III) (1 and 6), Tb(III) (2 and 7), and Sm(III) (3 and 8) exhibit strong characteristic emissions in the visible region, whereas Nd(III) (4 and 11) and Yb(III) (12) complexes display NIR luminescence upon irradiation at the ligand band. Moreover, the triplet state of H(2)hqc matches well with the emission level of Eu(III), Tb(III), and Sm(III) ions, which allows the preparation of new optical materials with enhanced luminescence properties.

Uranium(VI) Complexes with a Calix[4]arene‐Based 8‐Hydroxyquinoline Ligand: Thermodynamic and Structural Characterization Based on Calorimetry, Spectroscopy, and Liquid–Liquid Extraction

PubMed Central

Bauer, Anne; Jäschke, Astrid; Schöne, Sebastian; Barthen, Robert; März, Juliane; Patzschke, Michael; Kersting, Berthold; Fahmy, Karim; Oertel, Jana; Brendler, Vinzenz; Stumpf, Thorsten

2018-01-01

Abstract The environmental aspects of ore processing and waste treatment call for an optimization of applied technologies. There, understanding of the structure and complexation mechanism on a molecular scale is indispensable. Here, the complexation of UVI with a calix[4]arene‐based 8‐hydroxyquinoline ligand was investigated by applying a wide range of complementary methods. In solution, the formation of two complex species was proven with stability constants of log ß 1:1=5.94±0.02 and log ß 2:1=6.33±0.01, respectively. The formation of the 1:1 complex was found to be enthalpy driven [ΔH 1:1=(−71.5±10.0) kJ mol−1; TΔS 1:1=(−37.57±10.0) kJ mol−1], whereas the second complexation step was found to be endothermic and entropy driven [ΔH 2:1=(32.8±4.0) kJ mol−1; TΔS 2:1=(68.97±4.0) kJ mol−1]. Moreover, the molecular structure of [UO2(H6L)(NO3)](NO3) (1) was determined by single‐crystal X‐ray diffraction. Concluding, radiotoxic UVI was separated from a EuIII‐containing solution by the calix[4]arene‐based ligand in solvent extractions. PMID:29930893

Poly[[tetra-μ-cyanido-κ8 C:N-dodeca-cyanido-κ12 C-tris­(N,N-di­methyl­formamide-κO)tris­(methanol-κO)tris­(3,4,7,8-tetra­methyl-1,10-phenanthroline-κ2 N,N′)trimanganese(II)ditungstate(V)] dihydrate

PubMed Central

Yang, Fei-Lin; Yang, Dan

2014-01-01

The asymmetric unit of the title compound, {[Mn3{W(CN)8}2(C16H16N2)3(C3H7NO)3(CH3OH)3]·2H2O}n, consists of three [Mn(N,N-di­methyl­formamide)(methanol)(3,4,7,8-tetra­methyl-1,10-phenanthroline)]2+ cations, two [W(CN)8]3− anions and two water mol­ecules. Each water mol­ecule is disordered over three sets of sites, with a refined occupancy ratio of 0.310 (9):0.275 (9):0.415 (9) for one mol­ecule and 0.335 (9):0.288 (9):0.377 (9) for the other mol­ecule. The MnII atoms exhibit a distorted octa­hedral geometry, while the WV atoms adopt a distorted square-anti­prismatic geometry. The MnII and WV atoms are linked alternatively through cyanide groups, forming a tetra­nuclear 12-atom rhombic metallacycle. Adjacent metallacycles are further connected by μ2-bridging cyanide anions, generating a 3,2-chain structure running parallel to [101]. Inter­chain π–π inter­actions are observed [centroid–centroid distances = 3.763 (3) and 3.620 (2) Å]. PMID:24860305

Electroluminescent Properties in Organic Light-Emitting Diode Doped with Two Guest Dyes

NASA Astrophysics Data System (ADS)

Mori, Tatsuo; Kim, Hyeong-Gweon; Mizutani, Teruyoshi; Lee, Duck-Chool

2001-09-01

An organic light-emitting diode (OLED) with a squarylium dye-doped aluminium quinoline (Alq3) emission layer prepared by vapor deposition method has a pure red emission. However, since its luminance and electroluminescence (EL) efficiency is poor, the authors attended to improve the EL efficiency by doping a photosensitizer dye (a styryl dye, DCM) in an emission layer. The EL efficiency and luminance of DCM- and Sq-doped OLEDs are 2-3 times higher than those of only Sq-doped OLEDs. It was found that the excited energy is transferred from Alq3 to Sq through DCM.

Low temperature transient response and electroluminescence characteristics of OLEDs based on Alq3

NASA Astrophysics Data System (ADS)

Yuan, Chao; Guan, Min; Zhang, Yang; Li, Yiyang; Liu, Shuangjie; Zeng, Yiping

2017-08-01

In this work, the organic light-emitting diodes (OLEDs) based on Alq3 are fabricated. In order to make clear the transport mechanism of carriers in organic light-emitting devices at low temperature, detailed electroluminescence transient response and the current-voltage-luminescence (I-V-L) characteristics under different temperatures in those OLEDs are investigated. It founds that the acceleration of brightness increases with increasing temperature is maximum when the temperature is 200 K and it is mainly affected by the electron transport layer (Alq3). The MoO3 injection layer and the electroluminescent layer have great influence on the delay time when the temperature is 200 K. Once the temperature is greater than 250 K, the delay time is mainly affected by the MoO3 injection layer. On the contrary, the fall time is mainly affected by the electroluminescent material. The Vf is the average growth rate of fall time when the temperature increases 1 K which represents the accumulation rate of carriers. The difference between Vf caused by the MoO3 injection layer is 0.52 us/K and caused by the electroluminescent material Ir(ppy)3 is 0.73 us/K.

Analysis of molybdenum, tungsten, and vanadium in surface water of the Atlantic Ocean using solid phase extraction with 8-hydroxyquinoline and ICP MS determination

NASA Astrophysics Data System (ADS)

Rimskaya-Korsakova, M. N.; Berezhnaya, E. D.; Dubinin, A. V.

2017-07-01

An analytical technique is proposed to determine ultratrace concentrations of Mo, V, and W found in seawater using mass spectrometry with inductively coupled plasma (ICP MS) after preliminary concentration by solid-phase extraction of metal complexes with 8-hydroxyquinoline (8-HQ) on C18 octadecyl silica. The technique utilizes 150 mL of a water sample. A preconcentration factor 50 is obtained. The detection limits are 0.25 nmol/kg, 0.041 nmol/kg, and 5 pmol/kg for Mo, V, and W, respectively. Dissolved Mo, V, and Wconcentrations in surface seawater from Atlantic Ocean transect were determined. The concentrations ranges along the transect were: 91-108 nmol/kg for Mo, 28-35 nmol/kg for V, and 55-75 pmol/kg for W. The Mo/W ratio varied from 1300 to 1800.

Copper(I)-catalyzed aryl bromides to form intermolecular and intramolecular carbon-oxygen bonds.

PubMed

Niu, Jiajia; Guo, Pengran; Kang, Juntao; Li, Zhigang; Xu, Jingwei; Hu, Shaojing

2009-07-17

A highly efficient Cu-catalyzed C-O bond-forming reaction of alcohol and aryl bromides has been developed. This transformation was realized through the use of copper(I) iodide as a catalyst, 8-hydroxyquinoline as a ligand, and K(3)PO(4) as a base. A variety of functionalized substrates were found to react under these reaction conditions to provide products in good to excellent yields.

A two-step dilution tris-egg yolk extender containing Equex STM significantly improves sperm cryopreservation in the African wild dog (Lycaon pictus).

PubMed

Van den Berghe, Femke; Paris, Monique Christina Johanna; Briggs, Michael Brent; Farstad, Wenche Kristin; Paris, Damien Boyd Bertrand Paul

2018-02-01

Conservation management of endangered African wild dogs (AWD; Lycaon pictus) can benefit greatly from development of sperm freezing and artificial insemination. Previous freezing attempts yielded nearly 0% motile sperm within 2 h of thawing. In this study, two canine freezing protocols were tested: Protocol 1: a one-step dilution in TRIS-20% egg yolk containing 8% glycerol; and Protocol 2: a two-step dilution in TRIS-20% egg yolk containing a final extender concentration of 5% glycerol and 0.5% Equex STM, coupled with a TRIS-citrate-fructose thawing solution. Semen was collected by electroejaculation from n = 24 AWDs, of which eight ejaculates of sufficient quality (four good quality with initial sperm motility of 75.0 ± 4.4% and four poor quality; showing rapid decrease in sperm motility to 3.3 ± 3.3% prior to freezing) were frozen. For good quality samples, motility and sperm motility index persisted for up to 8 h for Protocol 2, and was higher between 2 and 6 h after thawing with a decrease from 4 h of incubation. Motility dropped to nearly 0% after 2 h incubation for Protocol 1. Viability was higher for Protocol 2 throughout the 8 h of incubation, with a decrease after 6 h, compared to 4 h for Protocol 1. Acrosome integrity was higher for Protocol 2 throughout post-thaw incubation, with a decrease after 2 h for both protocols. Protocols did not differ in normal sperm morphology or DNA integrity. Poor quality samples yielded similar results, except for acrosome integrity, which declined for Protocol 2. In conclusion, a two-step dilution in TRIS-egg yolk-glycerol extender containing Equex STM yields significantly improved post-thaw quality and longevity of AWD spermatozoa, making it suitable for sperm banking and artificial insemination initiatives. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

sym-Trisubstituted 1,3,5-Triazine Derivatives as Promising Organic Corrosion Inhibitors for Steel in Acidic Solution.

PubMed

El-Faham, Ayman; Dahlous, Kholood A; Al Othman, Zeid A; Al-Lohedan, Hamad A; El-Mahdy, Gamal A

2016-03-31

Triazine derivatives, namely, 2,4,6-tris(quinolin-8-yloxy)-1,3,5-triazine (T3Q), N²,N⁴,N⁶-tris(pyridin-2-ylmethyl)-1,3,5-triazine-2,4,6-triamine (T3AMPy) and 2,2',2''-[(1,3,5-triazine-2,4,6-triyl)tris(azanediyl)] tris(ethan-1-ol) (T3EA) were synthesized and their inhibition of steel corrosion in hydrochloric acid solution was investigated using electrochemical techniques. The corrosion protection of the prepared compounds increased with increasing concentration and reached up to 98% at 250 ppm. The adsorption of T3Q, T3AMPy, and T3EA on the steel surface was in accordance with the Langmuir adsorption isotherm. The electrochemical results revealed that T3Q, T3AMPy and T3EA act as excellent organic inhibitors and can labeled as mixed type inhibitors. The efficiencies of the tested compounds were affected by the nature of the side chain present in the triazine ring, where T3EA gave the least inhibition while T3Q and T3AMPy gave higher and almost the same inhibition effects. The inhibition efficiencies obtained from the different electrochemical techniques were in good agreement.

Monitoring underlying epoxy-coated St-37 corrosion via 8-hydroxyquinoline as a fluorescent indicator

NASA Astrophysics Data System (ADS)

Roshan, Shamim; Sarabi Dariani, Ali Asghar; Mokhtari, Javad

2018-05-01

In the present study, successful performance of 8-hydroxyquinoline (8-HQ) as a ferric ion sensitive indicator is described. 8-HQ was used in epoxy coating because of its desirable properties. It doesn't exhibit premature fluorescence when mixed with coating precursors. Additionally it shows fluorescence turn-on mechanism upon chelate formation with Fe2+/Fe3+ ions produced during anodic reaction. The effect of different concentrations of 8-HQ (0.05, 0.1, 0.5 and 1 wt.%) incorporated in the epoxy coating on corrosion detection as well as optical and electrochemical behavior of the applied coating were studied. The fluorescence property of 8-HQ/Fe3+ solutions was evaluated by using fluorometer. The UV-Visible spectroscopy was used to investigate the effect of 8-HQ presence in the coating on transparency of the free films of the samples. The corrosion detection was performed by fluorescence microscope and the anti-corrosion performance of coated samples containing different concentrations of 8-HQ was studied using salt spray standard test and electrochemical impedance spectroscopy (EIS). The results of UV-Visible spectroscopy demonstrated that increasing 8-HQ concentration causes a slight decrease in coating transparency. According to the results of electrochemical impedance spectroscopy (EIS) measurements, the polarization resistance of the coated St-37 sample containing 0.1 wt.% 8-HQ was about 109 Ohm cm2 after 6 weeks immersion in corrosive electrolyte, while St-37 plates coated with other 8-HQ concentrations showed decreased resistance levels of about 106 Ohm cm2, during the same immersion period. Based on fluorescence microscopic investigation, as a result of incorporating 8-HQ into the epoxy matrix, fluorescence could be observed in regions where Fe2+/Fe3+ ions were produced through anodic reactions. This method is capable of detecting corrosion in situ at early stages before the metal surface suffers serious damages.

Synthesis and Electroluminescent Property of New Orange Iridium Compounds for Flexible White Organic Light Emitting Diodes.

PubMed

Lee, Ho Won; Jeong, Hyunjin; Kim, Young Kwan; Ha, Yunkyoung

2015-10-01

Recently, white organic light-emitting diodes (OLEDs) have aroused considerable attention because they have the potential of next-generation flexible displays and white illuminated applications. White OLED applications are particularly heading to the industry but they have still many problems both materials and manufacturing. Therefore, we proposed that the new iridium compounds of orange emitters could be demonstrated and also applied to flexible white OLEDs for verification of potential. First, we demonstrated the chemical properties of new orange iridium compounds. Secondly, conventional two kinds of white phosphorescent OLEDs were fabricated by following devices; indium-tin oxide coated glass substrate/4,4'-bis[N-(napthyl)-N-phenylamino]biphenyl/N,N'-dicarbazolyl-3,5-benzene doped with blue and new iridium compounds for orange emitting 8 wt%/1,3,5-tris[N-phenylbenzimidazole-2-yl]benzene/lithium quinolate/aluminum. In addition, we fabricated white OLEDs using these emitters to verify the potential on flexible substrate. Therefore, this work could be proposed that white light applications can be applied and could be extended to additional research on flexible applications.

Molecular-wire behavior of OLED materials: exciton dynamics in multichromophoric Alq3-oligofluorene-Pt(II)porphyrin triads.

PubMed

Montes, Victor A; Pérez-Bolívar, César; Agarwal, Neeraj; Shinar, Joseph; Anzenbacher, Pavel

2006-09-27

Donor-bridge-acceptor triads consisting of the Alq3 complex, oligofluorene bridge, and PtII tetraphenylporphyrin (PtTPP) were synthesized. The triads were designed to study the energy level/distance-dependence in energy transfer both in a solution and in solid state. The materials show effective singlet transfer from the Alq3-fluorene fluorophore to the porphyrin, while the triplet energy transfer, owing to the shorter delocalization of triplet excitons, appears to take place via a triplet energy cascade. Using femtosecond transient spectroscopy, the rate of the singlet-singlet energy transfer was determined. The exponential dependence of the donor-acceptor distance and the respective energy transfer rates of 7.1 x 1010 to 1.0 x 109 s-1 with the attenuation factor â of 0.21 +/- 0.02 A-1 suggest that the energy transfer proceeds via a mixed incohererent wire/superexchange mechanism. In the OLEDs fabricated using the Alq3-oligofluorene-PtTPP triads with better triplet level alignment, the order of a magnitude increase in efficacy appears to be due to facile triplet energy transfer. The devices, where the triplet-triplet energy transfer is of paramount importance, showed high color purity emission (CIE X,Y: 0.706, 0.277), which is almost identical to the emission from thin films. Most importantly, we believe that the design principles demonstrated above are general and may be used to prepare OLED materials with enhanced quantum efficacy at lowered operational potentials, being crucial for improved lifespan of OLEDs.

Semen coagulum liquefaction, sperm activation and cryopreservation of capuchin monkey (Cebus apella) semen in coconut water solution (CWS) and TES-TRIS.

PubMed

Oliveira, Karol G; Miranda, Stefania A; Leão, Danuza L; Brito, Adriel B; Santos, Regiane R; Domingues, Sheyla F S

2011-01-01

The objectives of the present study were to test the effect of coconut water solution and TES-TRIS on the seminal coagulum liquefaction, sperm activation in fresh diluted semen, and on the cryopreservation of semen from capuchin monkeys (Cebus apella). Semen was collected from six males by electro-ejaculation, diluted in TES-TRIS or coconut water solution (CWS), and incubated at 35°C until the coagulated fraction of the semen was completely liquefied. In the experiment I, after liquefaction, samples were diluted in TES-TRIS or CWS, plus 6 and 10mM/mL of caffeine. Sperm motility and vigor were evaluated during 5h. For experiment II, after liquefaction, semen samples were extended in TES-TRIS (3.5% glycerol in the final solution) or CWS (2.5% glycerol in the final solution), cryopreserved and stored in liquid nitrogen for 1 week. The seminal coagulum was liquefied in (mean±SDM) 4.5±1.7 and 2.8±1.1h in TES-TRIS and CWS, respectively. Sperm were motile in TES-TRIS and CWS for 5.0±1.4 and 1.0±0.5h, respectively. The mean motility in this period was 38±22% (TES-TRIS) and 22.0±16.0 (CWS). Motility increased after caffeine addition only in samples diluted in CWS containing 6mM (22.5±16.0) or 10mM (28.0±19.0) caffeine. Post-thaw live sperm percentage was 26.2% in TES-TRIS and 13.2% in CWS. For cryopreservation of semen from C. apella TES-TRIS (3.5% glycerol) was more appropriate than CWS (2.5% glycerol). CWS+caffeine potentially increase sperm motility and may be useful in artificial insemination of fresh diluted semen. Copyright © 2010 Elsevier B.V. All rights reserved.

Studies on the production of alkaline α-amylase from Bacillus subtilis CB-18.

PubMed

Nwokoro, Ogbonnaya; Anthonia, Odiase

2015-01-01

Amylases are among the main enzymes used in food and other industries. They hydrolyse starch molecules into polymers composing glucose units. Amylases have potential applications in a number of industrial processes including foods and pharmaceutical industries. Alkaline α-amylase has the potential of hydrolysing starch under alkaline pH and is useful in the starch and textile industries and as an ingredient of detergents. Amylases are produced from plants, however, microbial production processes have dominated applications in the industries. Optimization of microbial production processes can result in improved enzyme yields. Amylase activity was assayed by incubating the enzyme solution (0.5 ml) with 1% soluble starch (0.5 ml) in 0.1 M Tris/HCl buffer (pH 8.5). After 30 minutes, the reaction was stopped by the addition of 4 mL of 3,5-dinitrosalicylic acid (DNS) reagent then heated for 10 min in boiling water bath and cooled in a refrigerator. Absorbance readings were used to estimate the units of enzyme activity from glucose standard curve. Hydrolysed native starches from cassava, rice, corn, coco yam, maize and potato and soluble starch were adjusted to pH 8.5 prior to incubation with crude enzyme solution. Reducing sugars produced were therefore determined. The effect of pH on enzyme activity of the alkaline α-amylase was determined by using buffer solutions of different pH (potassium phosphate buffer, 6.0-7.0; Tris-HCl buffer 7.5 to 9.0 and carbonate/bicarbonate buffer, pH 9.5-11) for enzyme assay. The pH stability profile of the enzyme was determined by incubating 0.5 ml of α-amylase enzyme in 0.1 M Tris/HCl buffer (pH 8.5) and 0.5 ml of 1% (w/v) soluble starch (Merck) in 0.1 M Tris/HCl buffer (pH 8.5) for 3 h in various buffers. The effect of temperature on enzyme activity was studied by incubating 0.5 mL of the enzyme solution contained in the test tube and 0.5 mL of 1% soluble starch (Merck) solution prepared in 0.1 M Tris/HCl buffer (pH 8.5) for 3 h at various temperatures (25, 30, 35, 40, 45, 50, 55 and 60°C) in a thermo static water bath. The reactions were stopped by adding DNS reagent. The enzyme activity was therefore determined. Thermal stability was studied by incubating 0.5 ml of enzyme solution in 0.1 M Tris/HCl buffer (pH 8.5) and 0.5 ml of 1% (w/v) soluble starch (Merck) in 0.1 M Tris/HCl buffer (pH 8.5) for 3 h at various temperatures (20, 30, 40, 50, 60 and 70°C) for 60 min. The enzyme displayed optimal activity at pH 8.0 at which it produced maximum specific activity of 34.3 units/mg protein. Maximum stability was at pH 8.0 to 9.0. Maximum activity was observed at temperature of 50°C while thermo stability of the enzyme was observed at 40-50°C. The enzyme displayed a wide range of activities on starch and caused the release of 5.86, 4.75, 5.98, 3.44, 3.96, 8.84 mg/mL reducing sugar from cassava, potato, cocoyam, corn, rice and soluble starch respectively. This investigation reports some biochemical characterization of alkaline α-amylase from Bacillus subtilis CB-18. The substrate specificities of this enzyme on various starches suggested that the alkaline α-amylase enzyme had combined activities on raw and soluble starch.

Flow injection chemiluminescent determination of tetracycline using a tris(2,2'-bipyridine)ruthenium(II)-cerium(IV) sulphate system.

PubMed

Guo, Liangqia; Xie, Zenghong; Lin, Xucong; Liu, Xiaohua; Zhang, Weilin; Chen, Guonan

2004-01-01

A flow-injection chemiluminescence method for the determination of tetracycline was developed. The method is based on an enhancement by tetracycline of the chemiluminescence light emission of tris(2,2'-bipyridine)ruthenium(II). In sulphuric acid medium, the chemiluminescence is generated by the continuous oxidation of tris(2,2'-bipyridine)ruthenium(II) by cerium (IV) sulphate. The light-emission intensity is greatly enhanced in the presence of tetracycline. Under the optimum conditions, the calibration curve is linear over the range 3.75 x 10(-8) g/mL-1.5 x 10(-5) g/mL for tetracycline with the linear equation: deltaINT = 205.898 x C - 20.442 (R2 = 0.9974). The detection limit is 3.27 x 10(-8) g/mL. The proposed method was also successfully used to determine tetracycline in pharmaceutical formulation (mean recovery of tetracycline, 100.7%). Copyright 2004 John Wiley & Sons, Ltd.

Influence of chlorine or fluorine substitution on the estrogenic properties of 1-alkyl-2,3,5-tris(4-hydroxyphenyl)-1H-pyrroles.

PubMed

Schäfer, Anja; Wellner, Anja; Strauss, Martin; Schäfer, Andreas; Wolber, Gerhard; Gust, Ronald

2012-11-26

In continuation of our previous work, several 1-alkyl-2,3,5-tris(4-hydroxyphenyl)aryl-1H-pyrroles with chlorine or fluorine substituents in the aryl residues were synthesized and tested for estrogen receptor (ER) binding at isolated ERα/ERβ receptors (HAP assay) and in transactivation assays using ERα-positive MCF-7/2a as well as U2-OS/ERα and U2-OS/ERβ cells. In the competition experiment at ERα the compounds displayed very high relative binding affinities of up to 37% (determined for 8m) but with restricted subtype selectivity (e.g., ERα/ERβ (8m) = 9). The highest estrogenic potency in ERα-positive MCF-7/2a cells was determined for 2,3,5-tris(2-fluoro-4-hydroxyphenyl)-1-propyl-1H-pyrrole 8m (EC(50) = 23 nM), while in U2-OS/ERα cells 2-(2-fluoro-4-hydroxyphenyl)-3,5-bis(4-hydroxyphenyl)-1-propyl-1H-pyrrole 8b (EC(50) = 0.12 nM) was the most potent agonist, only 30-fold less active than estradiol (E2, EC(50) = 0.004 nM). In U2-OS/ERβ cells for all pyrroles no transactivation could be observed, which indicates that they are selective ERα agonists in cellular systems.

Alq3 coated silicon nanomembranes for cavity optomechanics

NASA Astrophysics Data System (ADS)

Fogliano, Francesco; Ortu, Antonio; Camposeo, Andrea; Pisignano, Dario; Ciampini, Donatella; Fuso, Francesco; Arimondo, E.

2016-09-01

The optomechanical properties of a silicon-nitride membrane mirror covered by Alq3 and Silver layers are investigated. Excitation at two laser wavelengths, 780 and 405 nm, corresponding to different absorptions of the multilayer, is examined. Such dual driving will lead to a more flexible optomechanical operation. Topographic reconstruction of the whole static membrane deformation and cooling of the membrane oscillations are reported. The cooling, observed for blue laser detuning and produced by bolometric forces, is deduced from the optomechanical damping of the membrane eigenfrequency. We determine the presence of different contributions to the photothermal response of the membrane.

F4TCNQ-Induced Exciton Quenching Studied by Using in-situ Photoluminescence Measurements

NASA Astrophysics Data System (ADS)

Zhu, Jian; Lu, Min; Wu, Bo; Hou, Xiao-Yuan

2012-09-01

The role of F4TCNQ as an exciton quenching material in thin organic light-emitting films is investigated by means of in situ photoluminescence measurements. C60 was used as another quenching material in the experiment for comparison, with Alq3 as a common organic light-emitting material. The effect of the growth sequence of the materials on quenching was also examined. It is found that the radius of Förster energy transfer between F4TCNQ and Alq3 is close to 0 nm and Dexter energy transfer dominates in the quenching process.

Electron transport and noise spectroscopy in organic magnetic tunnel junctions with PTCDA and Alq3 barriers

NASA Astrophysics Data System (ADS)

Martinez, Isidoro; Cascales, Juan Pedro; Hong, Jhen-Yong; Lin, Minn-Tsong; Prezioso, Mirko; Riminucci, Alberto; Dediu, Valentin A.; Aliev, Farkhad G.

2016-10-01

The possible influence of internal barrier dynamics on spin, charge transport and their fluctuations in organic spintronics remains poorly understood. Here we present investigation of the electron transport and low frequency noise at temperatures down to 0.3K in magnetic tunnel junctions with an organic PTCDA barriers with thickness up to 5 nm in the tunneling regime and with 200 nm thick Alq3 barrier in the hopping regime. We observed high tunneling magneto-resistance at low temperatures (15-40%) and spin dependent super-poissonian shot noise in organic magnetic tunnel junctions (OMTJs) with PTCDA. The Fano factor exceeds 1.5-2 values which could be caused by interfacial states controlled by spin dependent bunching in the tunneling events through the molecules.1 The bias dependence of the low frequency noise in OMTJs with PTCDA barriers which includes both 1/f and random telegraph noise activated at specific biases will also be discussed. On the other hand, the organic junctions with ferromagnetic electrodes and thick Alq3 barriers present sub-poissonian shot noise which depends on the temperature, indicative of variable range hopping.

Isolation and reconstitution of iron- and manganese-containing superoxide dismutases from Bacteroides thetaiotaomicron.

PubMed Central

Pennington, C D; Gregory, E M

1986-01-01

Superoxide dismutase (SOD) from extracts of anaerobically maintained Bacteroides thetaiotaomicron was a dimer of equally sized 23,000-molecular-weight monomers joined noncovalently. A preparation with a specific activity of 1,200 U/mg contained 1.1 g-atom of Fe, 0.6 g-atom of Zn, and less than 0.05 g-atom of Mn per mol of dimer. The apoprotein, prepared by dialysis of iron-SOD in 5 M guanidinium chloride-20 mM 8-hydroxyquinoline, had no superoxide-scavenging activity when renatured without exogenous metal. Enzymatic activity was restored to the denatured apoprotein by dialysis against either 1 mM Fe(NH4)2 or 1 mM MnCl2 in 20 mM Tris (pH 7.0). The Fe-reconstituted enzyme and the native enzyme were inhibited approximately 50% by 0.2 mM NaN3, whereas the Mn-reconstituted enzyme was inhibited 60% by 10 mM NaN3. Aeration of the anaerobic cells resulted in a fourfold induction of an azide-resistant SOD. The enzyme (43,000 molecular weight) isolated from aerated cells was a dimer of equally sized subunits. The metal content was 1.0 g-atom of Mn, 0.55 g-atom of Fe, and 0.3 g-atom of Zn per mol of dimer. Enzymatic activity of the denatured apoprotein from this enzyme was also restored on addition of either iron or manganese. The constitutive Fe-SOD and the O2-induced Mn-SOD, tested alone and in combination, migrated identically on acrylamide gels, had similar amino acid compositions, and had alanine as the sole N-terminal amino acid. These data are consistent with the synthesis of a single apoprotein in either anaerobically maintained or oxygenated cells. We have observed a similar phenomenon with SOD from Bacteroides fragilis (E. M. Gregory, Arch. Biochem. Biophys. 238:83-89, 1985). PMID:3700336

Organophosphorus flame retardants (PFRs) and plasticizers in house and car dust and the influence of electronic equipment.

PubMed

Brandsma, Sicco H; de Boer, Jacob; van Velzen, Martin J M; Leonards, Pim E G

2014-12-01

All nine PFRs studied were detected in house and car dust from the Netherlands with the exception of tris(butyl) phosphate (TNBP) and tris(isobutyl) phosphate (TIBP) in car dust. Tris(2-butoxyethyl) phosphate (TBOEP, median 22 μg g(-1)) was dominant in house dust collected around and on electronics followed by tris(2-chloroisopropyl) phosphate (TCIPP, median 1.3 μg g(-1)), tris(2-chloroethyl) phosphate (TCEP, median 1.3 μg g(-1)) and tris(phenyl) phosphate (TPHP, median 0.8 μg g(-1)). Levels of TPHP and tris(methylphenyl) phosphate (TMPP, also known as TCP) in house dust on electronics were significantly higher than in house dust collected around electronics, suggesting that electronic equipment has limited contribution to the PFR levels in house dust, with the exception of TPHP and TMPP. Car dust was dominated by tris(1,3-dichloroisopropyl) phosphate (TDCIPP) with the highest levels found in dust collected from the car seats (1100 μg g(-1)). The mean TDCIPP and TCIPP levels observed in car dust were significantly higher than the levels observed in dust collected around electronics. Significantly higher mean TMPP levels in dust taken from car seats were found compared to dust collected around the equipment (p<0.05). This is probably influenced by the use of TDCIPP, TCIPP in polyurethane foam (car seats) and the use of TMPP as plasticizer in car interiors. Worldwide four PFR patterns were observed in house dust. The PFR pattern in the Netherlands of TDCIPP, TMPP, TCEP, TCIPP and TPHP in house dust is comparable to the pattern found in six other countries, which may point to identical sources of these PFRs in the indoor environment. However, the PFR levels between the countries and within countries showed high variation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Tris-EDTA significantly enhances antibiotic efficacy against multidrug-resistant Pseudomonas aeruginosa in vitro.

PubMed

Buckley, Laura M; McEwan, Neil A; Nuttall, Tim

2013-10-01

Multidrug-resistant Pseudomonas aeruginosa commonly complicates chronic bacterial otitis in dogs. The aim of this in vitro study was to determine the effect of ethylenediaminetetraacetic acid-tromethamine (Tris-EDTA) on the minimal bactericidal concentrations (MBCs) and minimal inhibitory concentrations (MICs) of marbofloxacin and gentamicin for multidrug-resistant P. aeruginosa isolates from cases of canine otitis. Eleven isolates were identified as multidrug resistant on disc diffusion; 10 were resistant to marbofloxacin and two were resistant to gentamicin. Isolates were incubated for 90 min with each antibiotic alone and in combination with Tris-EDTA at concentrations of 0.075 μg/mL to 5 mg/mL for marbofloxacin, 0.001 μg/mL to 10 mg/mL for gentamicin and 17.8:4.7 to 0.14:0.04 mg/mL for Tris-EDTA. Positive and negative controls were included. Aliquots of each antibiotic and/or Tris-EDTA concentration were subsequently transferred to sheep blood agar to determine the MBCs, and tryptone soy broth was added to the remaining suspensions to determine the MICs. Tris-EDTA alone was bacteriostatic but not bactericidal at any concentration. The addition of Tris-EDTA significantly reduced the median MBC (from 625 to 468.8 μg/mL; P < 0.001) and MIC (from 29.3 to 2.4 μg/mL; P = 0.008) of marbofloxacin, and the median MBC (from 625 to 39.1 μg/mL) and MIC (from 19.5 to 1.2 μg/mL) of gentamicin (both P < 0.001). Tris-EDTA significantly reduced the MBCs and MICs of marbofloxacin and gentamicin for multidrug-resistant P. aeruginosa in vitro. This may be of use to clinicians managing these infections in dogs. © 2013 ESVD and ACVD.

Synthesis, spectroscopic, thermal, voltammetric studies and biological activity of crystalline complexes of pyridine-2,6-dicarboxylic acid and 8-hydroxyquinoline

NASA Astrophysics Data System (ADS)

Çolak, Alper Tolga; Çolak, Ferdağ; Yeşilel, Okan Zafer; Büyükgüngör, Orhan

2009-11-01

Two new compounds (8-H 2Q) 2[M(dipic) 2]·6H 2O (M = Co ( 1) and Ni ( 2), 8-HQ = 8-hydroxyquinoline, dipic = dipicolinate) have been prepared and characterized by elemental analysis, spectral (IR and UV-vis), thermal analyses, magnetic measurements and single-crystal X-ray diffraction techniques. Both 1 and 2 consist two 8-hydroxyquinolinium cations, one bis(dipicolinate)M(II) anion [M = Co(II), Ni(II)] and six uncoordinated water molecules. Both 1 and 2 crystallize in the monoclinic space group C2/c. In the compounds anion, each dipic ligand simultaneously exhibits tridentate coordination modes through N atom of pyridine ring and oxygen atoms of the carboxylate groups. The crystal packing of 1 and 2 is a composite of intermolecular hydrogen bonding and C-O⋯π interactions. The in vitro antibacterial and antifungal activities of 1 and 2 were evaluated by the agar well diffusion method by MIC tests. Both new compounds showed the same antimicrobial activity against Gram-positive bacteria and yeast and fungi expect Gram-negative bacteria.

High efficiency fluorescent white OLEDs based on DOPPP

NASA Astrophysics Data System (ADS)

Zhang, Gang; Chen, Chen; Lang, Jihui; Zhao, Lina; Jiang, Wenlong

2017-08-01

The white organic light-emitting devices (WOLED) with the structures of ITO/m-MTDATA (10 nm)/NPB (30 nm)/Rubrene (0.2 nm)/DOPPP (x nm)/TAz (10 nm)/Alq3 (30 nm)/LiF (0.5 nm)/Al and ITO/NPB (30 nm)/DPAVBi:Rubrene (2 wt.%, 20 nm)/ DOPPP (x nm)/TAZ (10 nm)/Alq3 (30 nm)/LiF (0.5 nm)/Al (100 nm) have been fabricated by the vacuum thermal evaporation method. The results show that the chroma of the non-doped device is the best and the color coordinates are in the range of white light. The maximum luminance is 12,750 cd/m2 and the maximum current efficiency is 8.55 cd/A. The doped device A has the maximum luminance (16,570 cd/m2), when the thickness of blue layer DOPPP is 25 nm, and the doped device B achieves the highest efficiency (10.47 cd/A), when the thickness of DOPPP is 15 nm. All the performances of the doped devices are better than the non-doped one. The results demonstrate that the doped structures can realize the energy transfer and then improve the performance of the device effectively.

Covalent Organic Framework Functionalized with 8-Hydroxyquinoline as a Dual-Mode Fluorescent and Colorimetric pH Sensor.

PubMed

Chen, Long; He, Linwei; Ma, Fuyin; Liu, Wei; Wang, Yaxing; Silver, Mark A; Chen, Lanhua; Zhu, Lin; Gui, Daxiang; Diwu, Juan; Chai, Zhifang; Wang, Shuao

2018-05-09

Real-time and accurate detection of pH in aqueous solution is of great significance in chemical, environmental, and engineering-related fields. We report here the use of 8-hydroxyquinoline-functionalized covalent organic framework (COF-HQ) for dual-mode pH sensing. In the fluorescent mode, the emission intensity of COF-HQ weakened as the pH decreased, and also displayed a good linear relationship against pH in the range from 1 to 5. In addition, COF-HQ showed discernible color changes from yellow to black as the acidity increased and can be therefore used as a colorimetric pH sensor. All these changes are reversible and COF-HQ can be recycled for multiple detection runs owing to its high hydrolytical stability. It can be further assembled into a mixed matrix membrane for practical applications.

[Study on the movement of the carrier recombination region in organic light-emitting diodes (OLEDs) based on DPVBi/Alq3].

PubMed

Yan, Guang; Zhao, Su-ling; Xu, Zheng; Zhang, Fu-jun; Kong, Chao; Liu, Xiao-dong; Gong, Wei; Gao, Li-yan

2011-07-01

Series of organic light emitting devices with basic structure of ITO/PCBM: PVK(x Wt%, approximately 40 nm)/DPVBi(30 nm)/Alq3 (30 nm)/Al were fabricated in order to investigate the carrier recombination region movement in these devices. The carrier injection-dependent, the carrier transport-dependent and the voltage-dependent carrier recombination region movements were investigated respectively by modifying cathode with lithium fluoride, by changing the doping concentration of PCBM and by changing the voltage on the devices. The physical mechanism behind the voltage-dependent carrier recombination region movement was discussed.

The design of cathode for organic photovoltaic devices

NASA Astrophysics Data System (ADS)

Song, De; Shi, Feng; Xia, Xuan; Li, Ye; Duanmu, Qingduo

2016-11-01

We have discussed the effect of the residual gas in the Al metal cathode deposition process and consequently influence the performance of organic photovoltaic devices (such as organic photoelectron detector or solar cell). We believe that the origin of degradation in Jsc and FF from the Al cathode device should be the formation of AlOx in the C60-Al interface, which contaminate the interface and plays a role like an energy barrier that block the charge collect process. To solve this problem the Ag and Alq3 layer had been inserted before the Al. Owing to the advantageous of Alq3 and Ag layer, the device which Al cathode prepared at a lower vacuum condition exhibits a comparable performance to that device which Al cathode deposited in regular situation. As an additional benefit, since the introducing of Alq3/Ag layer in the VOPc/C60 organic photovoltaic device performs a better near-infrared response, this phenomenon has been confirmed by means of both simulation and experimental data. So the design of our new cathode structure provides a degree of freedom to modulate the light absorption for organic photovoltaic devices in short-wave and long-wave.

Anticlostridial agent 8-hydroxyquinoline improves the isolation of faecal bifidobacteria on modified Wilkins-Chalgren agar with mupirocin.

PubMed

Novakova, J; Vlkova, E; Salmonova, H; Pechar, R; Rada, V; Kokoska, L

2016-04-01

The need for suitable selective cultivation media for the isolation of Bifidobacterium spp. continues to be a real concern in the field of intestinal microbiology. Isolation of bifidobacteria from human and animal faecal samples using selective agar plating may be problematic especially in samples with increased clostridial counts than bifidobacterial counts. Due to the absence of anticlostridial agents in existing selective media, clostridia can displace bifidobacteria resulting in incorrect estimation of their counts. Therefore, we supplemented the existing selective medium 'modified Wilkins Chalgren agar with mupirocin' (MWM) with 90 mg l(-1) of 8-hydroxyquinoline (8HQ), which was recently proved to act selectively against clostridia. The newly composed 'modified Wilkins-Chalgren agar with 8HQ' (MWMQ) was tested on pure bifidobacterial and clostridial strains, their mixtures, and using faecal samples of mammalian origin; its selectivity was evaluated by genus-specific identification of isolates. The results demonstrated that the presence of 8HQ in this agar eliminated the growth of nonbifidobacterial strains on MWMQ compared to that on MWM, whereas the recovery of bifidobacterial counts was at satisfactory levels. In conclusion, MWMQ could be recommended for bifidobacterial isolation from human and animal faeces especially when bifidobacteria are not numerically dominant and there are chances of clostridial contamination. Routine isolation of bifidobacteria from mammalian faeces does not use a reliable selective agar with an anticlostridial agent. Overgrowth of clostridia may result in incorrect estimation of bifidobacterial counts. Thus, in order to improve the selectivity of existing media for bifidobacterial isolation, we chose the modified Wilkins-Chalgren agar with mupirocin and supplemented it with 8-hydroxyquinoline (8HQ), a molecule that shows anticlostridial activity without affecting the growth of bifidobacteria. This newly composed medium showed enhanced selectivity and specificity compared to the original medium and therefore, can be recommended for the isolation of bifidobacteria from mammal faeces. © 2016 The Society for Applied Microbiology.

Highly efficient single-layer dendrimer light-emitting diodes with balanced charge transport

NASA Astrophysics Data System (ADS)

Anthopoulos, Thomas D.; Markham, Jonathan P. J.; Namdas, Ebinazar B.; Samuel, Ifor D. W.; Lo, Shih-Chun; Burn, Paul L.

2003-06-01

High-efficiency single-layer-solution-processed green light-emitting diodes based on a phosphorescent dendrimer are demonstrated. A peak external quantum efficiency of 10.4% (35 cd/A) was measured for a first generation fac-tris(2-phenylpyridine) iridium cored dendrimer when blended with 4,4'-bis(N-carbazolyl)biphenyl and electron transporting 1,3,5-tris(2-N-phenylbenzimidazolyl)benzene at 8.1 V. A maximum power efficiency of 12.8 lm/W was measured also at 8.1 V and 550 cd/m2. These results indicate that, by simple blending of bipolar and electron-transporting molecules, highly efficient light-emitting diodes can be made employing a very simple device structure.

N-Picolyl Derivatives of Kemp’s Triamine as Potential Antitumor Agents: A Preliminary Investigation

PubMed Central

Regino, Celeste Aida S.; Torti, Suzy V.; Ma, Rong; Yap, Glenn P.A.; Kreisel, Kevin A.; Torti, Frank M.; Planalp, Roy P.; Brechbiel, Martin W.

2008-01-01

Pre-organized tripodal ligands such as the N-picolyl derivatives of cis,cis-1,3,5-triamino-cis,cis-1,3,5-trimethylcyclohexane (Kemp’s triamine) were prepared as analogs to N,N’,N”- tris(2-pyridylmethyl)-cis,cis-1,3,5-triaminocyclohexane (tachpyr) in hopes of enhancing the rate of formation and stability of the metal complexes. A tricyclic bisaminal was formed via the reduction of the Schiff base while the tri(picolyl) derivative was synthesized via reductive amination of pyridine carboxaldehyde. Their cytotoxicities to the HeLa cell line were evaluated and directly compared to tachpyr and N,N’,N”- tris(2-pyridylmethyl)-tris(2-aminoethyl)amine (trenpyr). Results indicate that N,N’,N”-tris(2-pyridylmethyl)-cis,cis-1,3,5-triamino-cis,cis-1,3,5-trimethylcyclohexane (Kemp’s pyr) exhibits cytotoxic activity against the HeLa cancer cell line comparable to tachpyr (IC50 ~ 8.0 µM). Both Kemp’s pyr and tachpyr show higher cytotoxic activity over the aliphatic analogue of trenpyr (IC50 ~ 14 µM) suggesting that the major contributor to the activity is the ligand’s ability to form a stable and tight complex and that the equatorial/axial equilibrium impacting the complex formation for the cyclohexane-based ligands is not significant. PMID:16335923

A homologous series of regioselectively tetradeprotonated group 8 metallocenes: new inverse crown ring compounds synthesized via a mixed sodium-magnesium tris(diisopropylamide) synergic base.

PubMed

Andrikopoulos, Prokopis C; Armstrong, David R; Clegg, William; Gilfillan, Carly J; Hevia, Eva; Kennedy, Alan R; Mulvey, Robert E; O'Hara, Charles T; Parkinson, John A; Tooke, Duncan M

2004-09-22

Subjecting ferrocene, ruthenocene, or osmocene to the synergic amide base sodium-magnesium tris(diisopropylamido) affords a unique homologous series of metallocene derivatives of general formula [(M(C(5)H(3))(2))Na(4)Mg(4)(i-Pr(2)N)(8)] (where M = Fe (1), Ru (2), or Os (3)). X-ray crystallographic studies of 1-3 reveal a common molecular "inverse crown" structure comprising a 16-membered [(NaNMgN)(4)](4+) "host" ring and a metallocenetetraide [M(C(5)H(3))(2)](4-) "guest" core, the cleaved protons of which are lost selectively from the 1, 1', 3, and 3'-positions. Variable-temperature NMR spectroscopic studies indicate that 1, 2, and 3 each exist as two distinct interconverting conformers in arene solution, the rates of exchange of which have been calculated using coalescence and EXSY NMR measurements.

Preconcentration of Zr, Hf, Nb, Ta and W in seawater using solid-phase extraction on TSK-8-hydroxyquinoline resin and determination by inductively coupled plasma-mass spectrometry.

PubMed

Firdaus, M Lutfi; Norisuye, Kazuhiro; Sato, Taishi; Urushihara, Shouhei; Nakagawa, Yusuke; Umetani, Shigeo; Sohrin, Yoshiki

2007-02-05

Here, we present the first simultaneous preconcentration and determination of ultratrace (pmol kg(-1) level) Zr, Hf, Nb, Ta and W in seawater, both in the form of dissolved and acid-dissolvable species. 8-Hydroxyquinoline (8HQ) bonded covalently to a vinyl polymer resin, TSK-8HQ, was used in a chelating adsorbent column to concentrate the metals. The greatest advantage of this resin is its endurance to 5M HF, since this is an effective eluent for all five metals. The analytes were successfully concentrated from 250 mL seawater with a 50-fold concentration factor through the column extraction and evaporation. The detection limit was 0.009-0.15 pmol kg(-1). The procedure blank determined using ultra pure water as a sample was 0.005-0.37 pmol kg(-1). The five metals were quantitatively recovered from seawater with good precision (2-4%). The effect of sample pH, sample flow rate, eluent composition and sample pretreatment were carefully studied. This method was applied to seawater.

Ultrafast photoelectron spectroscopy of small molecule organic films

NASA Astrophysics Data System (ADS)

Read, Kendall Laine

As research in the field of ultrafast optics has produced shorter and shorter pulses, at an ever-widening range of frequencies, ultrafast spectroscopy has grown correspondingly. In particular, ultrafast photoelectron spectroscopy allows direct observation of electrons in transient or excited states, regardless of the eventual relaxation mechanisms. High-harmonic conversion of 800nm, femtosecond, Ti:sapphire laser pulses allows excite/probe spectroscopy down into atomic core level states. To this end, an ultrafast, X-UV photoelectron spectroscopic system is described, including design considerations for the high-harmonic generation line, the time of flight detector, and the subsequent data collection electronics. Using a similar experimental setup, I have performed several ultrafast, photoelectron excited state decay studies at the IBM, T. J. Watson Research Center. All of the observed materials were electroluminescent thin film organics, which have applications as the emitter layer in organic light emitting devices. The specific materials discussed are: Alq, BAlq, DPVBi, and Alq doped with DCM or DMQA. Alq:DCM is also known to lase at low photoexcitation thresholds. A detailed understanding of the involved relaxation mechanisms is beneficial to both applications. Using 3.14 eV excite, and 26.7 eV probe, 90 fs laser pulses, we have observed the lowest unoccupied molecular orbital (LUMO) decay rate over the first 200 picoseconds. During this time, diffusion is insignificant, and all dynamics occur in the absence of electron transport. With excitation intensities in the range of 100μJ/cm2, we have modeled the Alq, BAlq, and DPVBi decays via bimolecular singlet-singlet annihilation. At similar excitations, we have modeled the Alq:DCM decay via Förster transfer, stimulated emission, and excimeric formation. Furthermore, the Alq:DCM occupied to unoccupied molecular orbital energy gap was seen to shrink as a function of excite-to-probe delay, in accordance with the expected relaxation within the excited states. Stable, shorter pulses allow finer temporal resolution and more efficient high-harmonic generation. This work therefore concludes by discussing a method for further shortening 25 femtosecond pulses via self-phase modulation, using filamentation in air and subsequent fiber channeling.

Bis[1-meth­oxy-2,2,2-tris­(pyrazol-1-yl-κN 2)ethane]­nickel(II) bis­(tri­fluoro­methane­sulfonate) methanol disolvate

PubMed Central

Lyubartseva, Ganna; Parkin, Sean; Mallik, Uma Prasad

2013-01-01

In the title salt, [Ni(C12H14N6O)2](CF3SO3)2·2CH3OH, the NiII ion is coordinated by six N atoms from two tridentate 1-meth­oxy-2,2,2-tris­(pyrazol-1-yl)ethane ligands in a distorted octa­hedral geometry. The NiII ion is situated on an inversion centre. The Ni—N distances range from 2.0589 (19) to 2.0757 (19) Å, intra-ligand N—Ni—N angles range from 84.50 (8) to 85.15 (8)°, and adjacent inter-ligand N—Ni—N angles range between 94.85 (8) and 95.50 (8)°. In the crystal, O—H⋯O hydrogen bonds between methanol solvent mol­ecules and tri­fluoro­methane­sulfonate anions are observed. PMID:24098170

A Diarylethene Derived Chemosensor for Colorimetric Sensing of Cu2+

NASA Astrophysics Data System (ADS)

Pu, Shouzhi; Sun, Qi; Zheng, Chunhong

2017-07-01

A diarylethene bearing a 8-hydroxyquinoline-linked salicylhydrazide Schift base unit has been synthesized. In CH3CN, the conpound displayed a highly selective and sensitive response to Cu2+ via perceptible color and UV-vis absorbance changes among the other tested metal ions. In the presence of Cu2+, the peak at 341 nm disappeared and concomitantly a new charge transfer absorption band emerged at 381 and 450 nm. Moreover, the compound formed host-guest complexe in 1:1 stoichiometry.

Highly effective synthesis of a cobalt(ii) metal-organic coordination polymer by using continuous flow chemistry.

PubMed

Gong, Chunhua; Zhang, Junyong; Zeng, Xianghua; Xie, Jingli

2016-12-20

The coordination polymer [Co 2 L 4 (H 2 O) 2 ]·CH 3 CN·H 2 O (HL = (E)-2-[2-(4-chlorophenyl)vinyl]-8-hydroxyquinoline) has been achieved with 95% yield by using an Asia flow synthesis system (chip reactor). Compared with the conventional batch-type methods such as diffusion, reflux and solvothermal reactions, higher yielding reactions carried out in a flow reactor have demonstrated that this technique is a powerful strategy to obtain coordination compounds.

Electrochemical preparation of tris(tert-butyldimethylsilyl)cyclopropene and its hydride abstraction to tris(tert-butyldimethylsilyl)cyclopropenium tetrafluoroborate

PubMed Central

Buchholz, Herwig A.; Prakash, G. K. Surya; Deffieux, Denis; Olah, George A.

1999-01-01

Electrochemical reductive tert-butyldimethylsilylation of tetrachlorocyclopropene to 1,2,3-tris(tert-butyldimethylsilyl)cyclopropene, a potential strained precursor for Diels–Alder and related cycloaddition reactions, is described. By hydride abstraction with nitrosonium tetrafluoroborate, 1,2,3-tris(tert-butyldimethylsilyl)cyclopropene is ionized quantitatively to Hückeloid 2π aromatic tris(tert-butyldimethylsilyl)cyclopropenium tetrafluoroborate. PMID:10468551

[Authentic leadership. Concept and validation of the ALQ in Spain].

PubMed

Moriano, Juan A; Molero, Fernando; Lévy Mangin, Jean-Pierre

2011-04-01

This study presents the validation of the Authentic Leadership Questionnaire (ALQ) in a sample of more than 600 Spanish employees. This questionnaire measures four distinct but related substantive components of authentic leadership. These components are: self-awareness, relational transparency, balanced processing, and internalized moral perspective. Structural equation modeling confirmed that the Spanish version of ALQ has high reliability and predictive validity for important leadership outputs such as perceived effectiveness of leadership, followers' extra effort and satisfaction with the leader.

Synthesis of Ferrite Nickel Nano-particles and Its Role as a p-Dopant in the Improvement of Hole Injection of an Organic Light-Emitting Diode

NASA Astrophysics Data System (ADS)

Noori, Maryam; Jafari, Mohammad Reza; Hosseini, Sayed Mohsen; Shahedi, Zahra

2017-07-01

We fabricated an organometallic complex based on zinc ions using zinc complex as a fluorescent in organic light-emitting diodes (OLEDs). Also, the nano-particles of ferrite nickel were produced in a simple aqueous system prepared by mixing Ni (NO3)2, Fe (NO3)3 and deionized water solutions. The synthesized zinc bis (8-hydroxyquinoline) (Znq2) complex and NiFe2O4 nano-particles were characterized by using x-ray diffraction (XRD), ultraviolet-visible (UV-Vis), Fourier transform infrared spectroscopy (FT-IR) as well as photoluminescence spectroscopy analysis. Their energy level was also determined by some cyclic voltammetry (CV) measurements. The maximum green photoluminescence was observed at 565 nm. The nano-particles of ferrite nickel were utilized in preparation of OLEDs by blending of the magnetic nano-particles with PEDOT:PSS and Zn-complex solutions. The electrical and optical performance of prepared OLEDs with/without doped nano-particle was studied. The samples were configured into two structures: (1) Indium Tin Oxide (ITO)/ poly(3,4-ethylenedi-oxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/Znq2/(2-4-biphenylyl)-5-phenyl-oxadiazole (PBD)/aluminum (Al) and (2) ITO/PEDOT:PSS:NiFe2O4(NPs)/Znq2/PBD/Al. Obtained results showed that the current density and electroluminescence efficiency were increased and the turn-on voltage decreased (about 3 V) by using nano-particles into a PEDOT:PSS layer (Hole transport layer). Also, the electroluminescence efficiency was decreased by incorporating magnetic nano-particles into a Zn-complex layer (emissive layer). It was found that utilizing NiFe2O4 nano-particles caused an increase of hole-injection layer conductivity effectively and a decrease of the turn-on voltage.

Effect of different concentrations of egg yolk and virgin coconut oil in Tris-based extenders on chilled and frozen-thawed bull semen.

PubMed

Tarig, A A; Wahid, H; Rosnina, Y; Yimer, N; Goh, Y M; Baiee, F H; Khumran, A M; Salman, H; Ebrahimi, M

2017-07-01

The aim of this study was to evaluate the effects of 8% virgin coconut oil (VCO) combined with different percentages of egg yolk in Tris extender on the quality of chilled and frozen-thawed bull semen. A total of 24 ejaculates from four bulls were collected using an electroejaculator. Semen samples were diluted with 8% VCO in Tris extender which contained different concentrations 0% (control), 4%, 8%, 12%, 16% and 20% egg yolk. The diluted semen samples were divided into two fractions: one was chilled and stored at 4°C until evaluation after 24, 72, and 144h; the second fraction was processed by chilling for 3h at 4°C to equilibrate, then packaged in 0.25ml straws and frozen and stored in liquid nitrogen at -196°C until evaluation after 7 and 14 days. Both chilled and frozen semen samples were then thawed at 37°C and assessed for general motility using computer-assisted semen analysis (CASA), viability, acrosome integrity, and morphology (eosin-nigrosin), membrane integrity (hypo-osmotic swelling test) and lipid peroxidation (thiobarbituric acid-reactive substances (TBARS)). The results indicate treatments with 8%, 12%, 16% and 20% egg yolk with 8% VCO had greater sperm quality (P<0.05) as compared with the control. The treatment with 20% egg yolk had the greatest sperm quality (P<0.05) among the treated groups for both chilled and frozen-thawed semen. In conclusion, the use of 8% VCO combined with 20% egg yolk in a Tris-based extender enhanced the values for chilled and frozen-thawed quality variables of bull sperm. Copyright © 2017 Elsevier B.V. All rights reserved.

Exciton emission from bare and hybrid plasmonic GaN nanorods

NASA Astrophysics Data System (ADS)

Mohammadi, Fatemesadat; Kunert, Gerd; Hommel, Detlef; Ge, Jingxuan; Duscher, Gerd; Schmitzer, Heidrun; Wagner, Hans Peter

We study the exciton emission of hybrid gold nanoparticle/Alq3 (aluminiumquinoline)/wurtzite GaN nanorods. GaN nanorods of 1.5 μm length and 250 nm diameter were grown by plasma assisted MBE. Hybrid GaN nanorods were synthesized by organic molecular beam deposition. Temperature and power dependent time integrated (TI) and time resolved (TR) photoluminescence (PL) measurements were performed on bare and hybrid structures. Bare nanorods show donor (D0,X) and acceptor bound (A0,X) exciton emission at 3.473 eV and at 3.463 eV, respectively. TR-PL trace modeling reveal lifetimes of 240 ps and 1.4 ns for the (D0,X) and (A0,X) transition. 10 nm gold coated GaN nanorods show a significant PL quenching and (D0,X) lifetime shortening which is tentatively attributed to impact ionization of (D0,X) due to hot electron injection from the gold nanoparticles. This is supported by electron energy loss spectroscopy that shows a redshift of a midgap state transition indicating a reduction of a preexisting band-bending at the nanorod surface due to positive charging of the gold nanoparticles. Inserting a nominally 5 nm thick Alq3 spacer between the nanorod and the gold reduces the PL quenching and lifetime shortening. Plasmonic nanorods with a 30 nm thick Alq3 spacer reveal lifetimes which are nearly identical to uncoated GaN nanorods.

Dielectric impedance and optical performance of quantum dots doped OLEDs

NASA Astrophysics Data System (ADS)

Jobin, Marc; Pellodi, Cédric; Emmenegger, Nicolas

2016-04-01

We investigate the effect of the incorporation of CdSe quantum dots (QD) in the standard ITO/TPD/Alq3/Al organic light emitting diodes (OLED's). The OLED's structures have been prepared in a double glove box coupled to a vacuum chamber containing both low and high temperature evaporators. For the standard (undoped) OLED's, the hole transport layer (HTL) consisting of 50nm of TPD is deposited by spin coating (8000rpm during 60 sec) and the 40nm of Alq3 were deposited at 2A/sec (organic crucible Radak-I). 150nm of Al were finally evaporated at 5A/s. For the CdSe-doped OLED's, the procedure was the same expect that the QD's were mixed with TPD in toluene before spin coating. During the thermal processing if the film, the QD's are expected to segregate to the surface, and then will be located at the TPD/Alq3 interface. The various layers were imaged by Atomic Force Microscopy (AFM) at each phase of the structure deposition, and we could indeed visualize the segregated QD's above the TPD film. AFM was systematically used to monitor the homogeneity and the thickness of the various films. The impedance of the non-encapsulated films structures were measured in air in the 40-40MHz frequency range, with bias at 0V (non-emitting), 2V (low emission) and 8V (strong emission). The corresponding dielectric spectra were analyzed with the standard Havriliak-Negami (HV) formula, where the conductive term has been subtracted from the data in case of light emission. We have measured a relaxation ranging from 100kHZ for the unbiased structure to 1MHz for 8V (strong emission). Apart from this expected relaxation, we found a second relaxation mechanism around 10 MHz. The origin of this second peak will be discussed. To monitor the optical emission of the OLED's, we have built a specific bench which allows for the quantitative measurement of the emission spectra and the dynamics behavior of the OLED's (raising and falling time). We found that the incorporation of the QD's unfortunately results in the decrease of the light emission but with a favorable modification of the light spectrum (around 700nm).

Polydopamine and Polydopamine-Silane Hybrid Surface Treatments in Structural Adhesive Applications.

PubMed

Tran, Ngon T; Flanagan, David P; Orlicki, Joshua A; Lenhart, Joseph L; Proctor, Kenneth L; Knorr, Daniel B

2018-01-30

Numerous studies have focused on the remarkable adhesive properties of polydopamine, which can bind to substrates with a wide range of surface energies, even under aqueous conditions. This behavior suggests that polydopamine may be an attractive option as a surface treatment in structural bonding applications, where good bond durability is required. Here, we assessed polydopamine as a surface treatment for bonding aluminum plates with an epoxy resin. A model epoxy adhesive consisting of diglycidyl ether of bisphenol A (DGEBA) and Jeffamine D230 polyetheramine was employed, and lap shear measurements (ASTM D1002 10) were made (i) under dry conditions to examine initial bond strength and (ii) after exposure to hot/wet (63 °C in water for 14 days) conditions to assess bond durability. Surprisingly, our results showed that polydopamine alone as a surface treatment provided no benefit beyond that obtained by exposing the substrates to an alkaline solution of tris buffer used for the deposition of polydopamine. This implies that polydopamine has a potential Achilles' heel, namely, the formation of a weak boundary layer that was identified using X-ray photoelectron spectroscopy (XPS) of the fractured surfaces. In fact, for longer deposition times (2.5 and 18 h), the tris buffer-treated surface outperformed the polydopamine surface treatments, suggesting that tris buffer plays a unique role in improving adhesive performance even in the absence of polydopamine. We further showed that the use of polydopamine-3-aminopropyltriethoxysilane (APTES) hybrid surface treatments provided significant improvements in bond durability at extended deposition times relative to both polydopamine and an untreated control.

Atomic Layer Deposition of Aluminum Sulfide: Growth Mechanism and Electrochemical Evaluation in Lithium-Ion Batteries

DOE PAGES

Meng, Xiangbo; Cao, Yanqiang; Libera, Joseph A.; ...

2017-10-01

This work describes the synthesis of aluminum sulfide (AlS x) thin films by atomic layer deposition (ALD) using tris(dimethylamido)aluminum and hydrogen sulfide. We employed a suite of in situ measurement techniques to explore the ALD AlS x growth mechanism, including quartz crystal microbalance, quadrupole mass spectrometry, and Fourier transform infrared spectroscopy. A variety of ex situ characterization techniques were used to determine the growth characteristics, morphology, elemental composition, and crystallinity of the resultant AlS x films. This study revealed that the AlS x growth was self-limiting in the temperature range 100–250 °C, and the growth per cycle decreased linearly withmore » increasing temperature from ~0.45 Å/cycle at 100 °C to ~0.1 Å/cycle at 250 °C. The AlSx films were amorphous in this temperature range. We conducted electrochemical testing to evaluate the ALD AlS x as a potential anode material for lithium-ion batteries (LIBs). Finally, the ALD AlS x exhibited reliable cyclability over 60 discharge–charge cycles with a sustainable discharge capacity of 640 mAh/g at a current density of 100 mA/g in the voltage window of 0.6–3.5 V.« less

Atomic Layer Deposition of Aluminum Sulfide: Growth Mechanism and Electrochemical Evaluation in Lithium-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meng, Xiangbo; Cao, Yanqiang; Libera, Joseph A.

This work describes the synthesis of aluminum sulfide (AlS x) thin films by atomic layer deposition (ALD) using tris(dimethylamido)aluminum and hydrogen sulfide. We employed a suite of in situ measurement techniques to explore the ALD AlS x growth mechanism, including quartz crystal microbalance, quadrupole mass spectrometry, and Fourier transform infrared spectroscopy. A variety of ex situ characterization techniques were used to determine the growth characteristics, morphology, elemental composition, and crystallinity of the resultant AlS x films. This study revealed that the AlS x growth was self-limiting in the temperature range 100–250 °C, and the growth per cycle decreased linearly withmore » increasing temperature from ~0.45 Å/cycle at 100 °C to ~0.1 Å/cycle at 250 °C. The AlSx films were amorphous in this temperature range. We conducted electrochemical testing to evaluate the ALD AlS x as a potential anode material for lithium-ion batteries (LIBs). Finally, the ALD AlS x exhibited reliable cyclability over 60 discharge–charge cycles with a sustainable discharge capacity of 640 mAh/g at a current density of 100 mA/g in the voltage window of 0.6–3.5 V.« less

DNA Cleavage, Cytotoxic Activities, and Antimicrobial Studies of Ternary Copper(II) Complexes of Isoxazole Schiff Base and Heterocyclic Compounds

PubMed Central

Chityala, Vijay Kumar; Sathish Kumar, K.; Macha, Ramesh; Tigulla, Parthasarathy; Shivaraj

2014-01-01

Novel mixed ligand bivalent copper complexes [Cu. L. A. ClO 4] and [Cu. L. A] where “L” is Schiff bases, namely 2-((3,4-dimethylisoxazol-5-ylimino)methyl)-4-bromophenol (DMIIMBP)/2-((3,4-dimethylisoxazol-5-ylimino)methyl)-4-chlorophenol (DMIIMCP), and “A” is heterocyclic compound, such as 1,10-phenanthroline (phen)/2,21-bipyridyl (bipy)/8-hydroxyquinoline (oxine)/5-chloro-8-hydroxyquinoline (5-Cl-oxine), have been synthesized. These complexes have been characterized by IR, UV-Vis, ESR, elemental analysis, magnetic moments, TG, and DTA. On the basis of spectral studies and analytical data, five-coordinated square pyramidal/four-coordinated square planar geometry is assigned to all complexes. The ligands and their ternary complexes with Cu(II) have been screened for antimicrobial activity against bacteria and fungi by paper disc method. The antimicrobial studies of Schiff bases and their metal complexes showed significant activity and further it is observed that the metal complexes showed more activity than corresponding Schiff bases. In vitro antitumor activity of Cu(II) complexes was assayed against human cervical carcinoma (HeLa) cancer cells and it was observed that few complexes exhibit good antitumor activity on HeLa cell lines. The DNA cleavage studies have also been carried out on pBR 322 and it is observed that these Cu(II) complexes are capable of cleaving supercoiled plasmid DNA in the presence of H2O2 and UV light. PMID:24895493

Extraction of glycogen on mild condition lacks AIG fraction.

PubMed

Ghafouri, Z; Rasouli, M

2016-12-01

Extraction of animal tissues with cold water or perchloric acid yields less glycogen than is obtained with hot-alkaline. Extraction with acid and alkaline gives two fractions, acid soluble (ASG) and insoluble glycogen (AIG). The aim of this work is to examine the hypothesis that not all liver glycogen is extractable by Tris-buffer using current techniques. Rat liver was homogenized with Tris-buffer pH 8.3 and extracted for the glycogen fractions, ASG and AIG. The degree of homogenization was changed to remove all glycogen. The content of glycogen was 47.7 ± 1.2 and 11.6 ± 0.8 mg/g wet liver in the supernatant and pellet of the first extraction respectively. About 24% of total glycogen is lost through the first pellet. Increasing the extent of homogenization from 30 to 180 sec and from 15000 to 20000 rpm followed with 30 sec ultrasonication did not improve the extraction. ASG and AIG constitute about 77% and 23% of the pellet glycogen respectively. Extraction with cold Tris-buffer failed to extract glycogen completely.  Increasing the extent of homogenization followed with ultrasonication also did not improve the extraction. Thus it is necessary to re-examine the previous findings obtained by extraction with cold Tris-buffer.

Structural and photophysical studies on gallium(III) 8-hydroxyquinoline-5-sulfonates. Does excited state decay involve ligand photolabilisation?

PubMed

Ramos, M Luísa; de Sousa, Andreia R E; Justino, Licínia L G; Fonseca, Sofia M; Geraldes, Carlos F G C; Burrows, Hugh D

2013-03-14

Multinuclear ((1)H, (13)C and (71)Ga) magnetic resonance spectroscopy (1D and 2D), DFT calculations and luminescence techniques have been used to study 8-hydroxyquinoline-5-sulfonate (8-HQS) and its complexes with Ga(III) in aqueous solutions. The study combines the high sensitivity of luminescence techniques and the selectivity of multinuclear NMR spectroscopy with the structural details accessible through DFT calculations, and aims to obtain a complete understanding of the complexation between the Ga(3+) ion and 8-HQS, and how this influences the luminescence behaviour. A full speciation study has been performed on this system and three complexes detected, with (metal : ligand) 1 : 1, 1 : 2 and 1 : 3 stoichiometries, the results being consistent with those previously found for the system Al(III)-8-HQS. Complexation in these systems is relevant to their potential biomedical, sensing and optoelectronic applications. On binding to Ga(III), a marked increase is seen in the intensity of the 8-HQS fluorescence band, which is accompanied by changes in the absorption spectra. These support the use of 8-HQS as a sensitive fluorescent sensor to detect Ga(3+) metal ions in surface waters, biological fluids, etc., and its metal complexes as an emitting or charge transport layer in light emitting devices. However, the fluorescence quantum yield of the Ga(III)-8-HQS 1 : 3 complex is about 35% of that of the corresponding system with Al(III). Although this may be due in part to a heavy atom effect favouring S(1)→ T(1) intersystem crossing with Ga(3+), this does not agree with transient absorption measurements on the triplet state yield, which is lower with the Ga(III) system than with Al(III). Instead, it is suggested that photolabilisation of ligand exchange plays a major role in nonradiative decay of the excited state and that this is more efficient with the Ga(3+) complex. Based on these results, suggestions are made of ways of enhancing fluorescence intensity in metal complexes with 8-HQS by inhibiting ligand exchange using surfactant complexation for applications in either sensing or optoelectronics.

Experimental and DFT studies of (E)-2-[2-(2,6-dichlorophenyl)ethenyl]-8-hydroxyquinoline: electronic and vibrational properties.

PubMed

Sun, Wenqi; Yuan, Guozan; Liu, Jingxin; Ma, Li; Liu, Chengbu

2013-04-01

The title molecule (E)-2-[2-(2,6-dichlorophenyl)ethenyl]-8-hydroxyquinoline (DPEQ) was synthesized and characterized by FT-IR, UV-vis, NMR spectroscopy. The molecular geometry, vibrational frequencies and gauge independent atomic orbital (GIAO) 1H and 13C NMR chemical shift values of the compound in the ground state have been calculated by using the density functional theory (DFT) method. All the assignments of the theoretical frequencies were performed by potential energy distributions using VEDA 4 program. The calculated results indicate that the theoretical vibrational frequencies, 1H and 13C NMR chemical shift values show good agreement with experimental data. The electronic properties like UV-vis spectral analysis and HOMO-LUMO analysis of DPEQ have been reported and compared with experimental data. Information about the size, shape, charge density distribution and site of chemical reactivity of the molecule has been obtained by mapping electron density isosurface with molecular electrostatic potential (MEP). Copyright © 2013 Elsevier B.V. All rights reserved.

Experimental and DFT studies of (E)-2-[2-(2,6-dichlorophenyl)ethenyl]-8-hydroxyquinoline: Electronic and vibrational properties

NASA Astrophysics Data System (ADS)

Sun, Wenqi; Yuan, Guozan; Liu, Jingxin; Ma, Li; Liu, Chengbu

2013-04-01

The title molecule (E)-2-[2-(2,6-dichlorophenyl)ethenyl]-8-hydroxyquinoline (DPEQ) was synthesized and characterized by FT-IR, UV-vis, NMR spectroscopy. The molecular geometry, vibrational frequencies and gauge independent atomic orbital (GIAO) 1H and 13C NMR chemical shift values of the compound in the ground state have been calculated by using the density functional theory (DFT) method. All the assignments of the theoretical frequencies were performed by potential energy distributions using VEDA 4 program. The calculated results indicate that the theoretical vibrational frequencies, 1H and 13C NMR chemical shift values show good agreement with experimental data. The electronic properties like UV-vis spectral analysis and HOMO-LUMO analysis of DPEQ have been reported and compared with experimental data. Information about the size, shape, charge density distribution and site of chemical reactivity of the molecule has been obtained by mapping electron density isosurface with molecular electrostatic potential (MEP).

Neurotoxicological and thyroid evaluations of rats developmentally exposed to tris(1,3-dichloro-2-propyl)phosphate (TDICPP) and tris(2-chloro-2-ethyl)phosphate(TCEP)

EPA Science Inventory

ABSTRACT: Tris(1,3-dichloro-2-propyl)phosphate (TDICPP) and tris(2-chloro-2-ethyl)phosphate (TCEP) are organophosphorous flame retardants with widespread usage and human exposures through food, inhalation, and dust ingestion. They have been detected in human tissues including ur...

Investigation of the Kinetic Energy Characterization of Advanced Ceramics

DTIC Science & Technology

2015-04-01

of Science, under a US Army International Technology Center contract. These ceramic formulations were compared with standard armor-grade boron ...Experimental Methodology 1 3. Results and Discussion 4 3.1 Aluminum Performance Baseline 4 3.2 Ceramic Inspection 6 3.3 Boron Carbide 6 3.4 Silicon...Carbide 7 3.5 Boron Carbide–Aluminum Nitride 7 3.6 Boron Carbide–Vanadium Diboride 7 3.7 Titanium Nitride–Aluminum Nitride 8 3.8 Comparative

TAME5OX, abiotic siderophore analogue to enterobactin involving 8-hydroxyquinoline subunits: Thermodynamic and photophysical studies

NASA Astrophysics Data System (ADS)

Akbar, Rifat; Baral, Minati; Kanungo, B. K.

2015-05-01

The synthesis, thermodynamic and photophysical properties of trivalent metal complexes of biomimetic nonadentate analogue, 5,5‧-(2-(((8-hydroxyquinolin-5-yl)methylamino)methyl)-2-methylpropane-1,3-diyl)bis(azanediyl)bis(methylene)diquinolin-8-ol (TAME5OX), have been described. Combination of absorption and emission spectrophotometry, potentiometry, electrospray mass spectrometry, IR, and theoretical investigation were used to fully characterize metal (Fe+3, Al+3 and Cr+3) chelates of TAME5OX. In solution, TAME5OX forms protonated complexes [M(H3L)]3+ below pH 3.4, which consecutively deprotonates through one to three-proton processes with rise of pH. The formation constants (Log β11n) of neutral complexes formed at or above physiological pH, have been determined to be 30.18, 23.27 and 22.02 with pM values of 31.16, 18.07 and 18.12 for Fe+3, Al+3 and Cr+3 ions, respectively, calculated at pH 7.4, indicating TAME5OX is a powerful among synthetic metal chelator. The results clearly demonstrate that the ligand in a tripodal orchestration firmly binds these ions over wide pH range and forms distorted octahedral complexes. The binding and the coordination event could be monitored from absorption and fluorescence spectroscopy. The high thermodynamic stability in water at physiological pH of ferric complex of TAME5OX indicates that these complexes are resistant to hydrolysis and therefore are well suited for the development of device for applications as probes. The ligand displays high sensitive fluorescence enhancement to Al3+ at pH 7.4, in water. Moreover, TAME5OX can distinguish Al3+ from Fe3+ and Cr3+ via two different sensing mechanisms: photoinduced electron transfer (PET) for Al3+ and internal charge transfer (ICT) for Fe3+ and Cr3+. Density functional theory was employed for optimization and evaluation of vibrational modes, NBO analysis, excitation and emission properties of the different species of metal complexes observed by solution studies.

TAME5OX, abiotic siderophore analogue to enterobactin involving 8-hydroxyquinoline subunits: thermodynamic and photophysical studies.

PubMed

Akbar, Rifat; Baral, Minati; Kanungo, B K

2015-05-05

The synthesis, thermodynamic and photophysical properties of trivalent metal complexes of biomimetic nonadentate analogue, 5,5'-(2-(((8-hydroxyquinolin-5-yl)methylamino)methyl)-2-methylpropane-1,3-diyl)bis(azanediyl)bis(methylene)diquinolin-8-ol (TAME5OX), have been described. Combination of absorption and emission spectrophotometry, potentiometry, electrospray mass spectrometry, IR, and theoretical investigation were used to fully characterize metal (Fe(+3), Al(+3) and Cr(+3)) chelates of TAME5OX. In solution, TAME5OX forms protonated complexes [M(H3L)](3+) below pH 3.4, which consecutively deprotonates through one to three-proton processes with rise of pH. The formation constants (Logβ11n) of neutral complexes formed at or above physiological pH, have been determined to be 30.18, 23.27 and 22.02 with pM values of 31.16, 18.07 and 18.12 for Fe(+3), Al(+3) and Cr(+3) ions, respectively, calculated at pH 7.4, indicating TAME5OX is a powerful among synthetic metal chelator. The results clearly demonstrate that the ligand in a tripodal orchestration firmly binds these ions over wide pH range and forms distorted octahedral complexes. The binding and the coordination event could be monitored from absorption and fluorescence spectroscopy. The high thermodynamic stability in water at physiological pH of ferric complex of TAME5OX indicates that these complexes are resistant to hydrolysis and therefore are well suited for the development of device for applications as probes. The ligand displays high sensitive fluorescence enhancement to Al(3+) at pH 7.4, in water. Moreover, TAME5OX can distinguish Al(3+) from Fe(3+) and Cr(3+) via two different sensing mechanisms: photoinduced electron transfer (PET) for Al(3+) and internal charge transfer (ICT) for Fe(3+) and Cr(3+). Density functional theory was employed for optimization and evaluation of vibrational modes, NBO analysis, excitation and emission properties of the different species of metal complexes observed by solution studies. Copyright © 2015 Elsevier B.V. All rights reserved.

New record of Scedosporium dehoogii from Chile: Phylogeny and susceptibility profiles to classic and novel putative antifungal agents.

PubMed

Alvarez, Eduardo; Sanhueza, Camila

Scedosporium species are considered emerging agents causing illness in immunocompromised patients. In Chile, only Scedosporium apiospermum, Scedosporium boydii and Lomentospora prolificans haven been reported previously. The study aimed to characterize genetically Scedosporium dehoogii strains from Chilean soil samples, and assessed the antifungal susceptibility profile to classic and novel putative antifungal molecules. In 2014, several samples were obtained during a survey of soil fungi in urban areas from Chile. Morphological and phylogenetic analyses of the internal transcribed spacer region (ITS), tubulin (TUB), and calmodulin (CAL) sequences were performed. In addition, the susceptibility profiles to classic antifungal and new putative antifungal molecules were determined. Four strains of Scedosporium dehoogii were isolated from soil samples. The methodology confirmed the species (reported here as a new record for Chile). Antifungal susceptibility testing demonstrates the low activity of terpenes (α-pinene and geraniol) against this species. Voriconazole (VRC), posaconazole (PSC), and the hydroxyquinolines (clioquinol, and 5,7-dibromo-8-hydroxyquinoline) showed the best antifungal activity. Our results demonstrate that Scedosporium dehoogii is present in soil samples from Chile. This study shows also that hydroxyquinolines have potential as putative antifungal molecules. Copyright © 2016 Asociación Española de Micología. Publicado por Elsevier España, S.L.U. All rights reserved.

[Pretreatment of Aluminum-Lithium Alloy Sample and Determination of Argentum and Lithium by Spectral Analysis].

PubMed

Zhou, Hui; Tan, Qian; Gao, Ya-ling; Sang, Shi-hua; Chen, Wen

2015-10-01

Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES), Flame Atomic Absorption Spectrometry (FAAS) and Visible Spectrometry (VS) was applied for determination of Ag and Li in lithium-aluminium alloy standard sample and test sample, their respective advantages and disadvantages were compared, the excellent selectivity of ICP-OES was confirmed by analyses of certified standard sample. Three different sample digestion methods were compared and discussed in this study. It was found that the better accuracy would be obtained by digesting sample with chloroazotic acid while the content of Li was measured by FAAS, and it was better to digest sample with hydrochloric acid and hydrogen peroxide while determining Ag and Li by ICP-OES simultaneously and determining Ag by FAAS and VS. The interference of co-existing elements and elimination methods was detailedly discussed. Ammonium hydroxide was added to adjust the sample solution into alkalescent and Al, Ti, Zr was precipitated by forming hydroxide precipitation, Mg and Cu was formed complex precipitation with 8-hydroxyquinoline in this condition, then the interference from matrix element to determinate Ag by FAAS was eliminated. In addition, phosphate was used to precipitate Ti to eliminate its interference for determination of Li by FAAS. The same treatment of determination for Ag by FAAS was used to eliminate the interference of matrix element for determination of Ag by VS, the excess of nitrate was added into sample and heated to release Ag+ from silver chloride complex, and the color of 8-hydroxyquinoline was eliminated because of decomposed by heating. The accuracy of analysis result for standard sample was conspicuously improved which confirms the efficient of the method to eliminate interference in this study. The optimal digestion method and eliminate interference method was applied to lithium-aluminium alloy samples. The recovery of samples was from 100.39% to 103.01% by ICP-OES determination for Ag, and from 100.42% to 103.01% by ICP-OES determination for Li. The recovery ranged from 95.91% to 99.98% by FAAS determination for Ag, and ranged from 98.04% to 99.98% for FAAS determination of Li. The recovery was from 98.00% to 101.00 by VS determination for Ag, the analysis results all meet the analysis requirement.

The effect of illumination and electrode adjustment on the carrier behavior in special multilayer devices

NASA Astrophysics Data System (ADS)

Deng, Yanhong; Ou, Qingdong; Wang, Jinjiang; Zhang, Dengyu; Chen, Liezun; Li, Yanqing

2017-08-01

Intermediate connectors play an important role in semiconductor devices, especially in tandem devices. In this paper, four types of different intermediate connectors (e.g. Mg:Alq3/MoO3, MoO3, Mg:Alq3, and none) and two kinds of modified electrode materials (LiF and MoO3) integrated into the special multilayer devices are proposed, with the aim of studying the impact of light illumination and electrode adjustment on the carrier behavior of intermediate connectors through the current density-voltage characteristics, interfacial electronic structures, and capacitance-voltage characteristics. The results show that the illumination enhances the charge generation and separation in intermediate connectors, and further electrode interface modifications enhance the functionality of intermediate connectors. In addition, the device with an efficient intermediate connector structure shows a photoelectric effect, which paves the way for organic photovoltaic devices to realize optical-electrical integration transformation.

Graphite furnace atomic absorption spectrometric detection of vanadium in water and food samples after solid phase extraction on multiwalled carbon nanotubes.

PubMed

Wadhwa, Sham Kumar; Tuzen, Mustafa; Gul Kazi, Tasneem; Soylak, Mustafa

2013-11-15

Vanadium(V) ions as 8-hydroxyquinoline chelates were loaded on multiwalled carbon nanotubes (MWNTs) in a mini chromatographic column. Vanadium was determined by graphite furnace atomic absorption spectrometry (GFAAS). Various analytical parameters including pH of the working solutions, amounts of 8-hydroxyquinoline, eluent type, sample volume, and flow rates were investigated. The effects of matrix ions and some transition metals were also studied. The column can be reused 250 times without any loss in its sorption properties. The preconcentration factor was found as 100. Detection limit (3 s) and limit of quantification (10 s) for the vanadium in the optimal conditions were observed to be 0.012 µg L(-1) and 0.040 μg L(-1), respectively. The capacity of adsorption was 9.6 mg g(-1). Relative standard deviation (RSD) was found to be 5%. The validation of the method was confirmed by using NIST SRM 1515 Apple leaves, NIST SRM 1570a Spinach leaves and GBW 07605 Tea certified reference materials. The procedure was applied to the determination of vanadium in tap water and bottled drinking water samples. The procedure was also successfully applied to microwave digested food samples including black tea, coffee, tomato, cabbage, zucchini, apple and chicken samples. Copyright © 2013 Elsevier B.V. All rights reserved.

[Validation of the Polish version of The Authentic Leadership Questionnaire for the of evaluation purpose of nursing management staff in national hospital wards].

PubMed

Sierpińska, Lidia

2013-09-01

The Authentic Leadership Questionnaire (ALQ) is a standardized research instrument for the evaluation of individual elements of leader's conduct which contribute to the authentic leadership. The application of this questionnaire in Polish conditions required to carry out the validation process. The aim of the study was to evaluate of validity and reliability of the Polish version of the American research instrument for the needs of evaluation of authenticity of leadership of the nursing management in Polish hospitals. The study covered 286 nurses (143 head nurses and 143 of their subordinates) employed in 45 hospitals in Poland. Theoretical validity of the instrument was evaluated using Fisher's transformation (r-Person correlation coefficient), while the criterion validity of the ALQ was evaluated using rho-Spearman correlation coefficient and the BOHIPSZO questionnaire. The reliability of the ALQ was assessed by means of the Cronbach-alpha coefficient. The ALQ questionnaire applied for the evaluation of authenticity of leadership of the nursing management in Polish hospital wards shows an acceptable theoretical and criterion validity and reliability (Cronbach-alpha coefficient 0.80). The Polish version of the ALQ is valid and reliable, and may be applied in studies concerning the evaluation of authenticity of leadership of the nursing management in Polish hospital wards.

Crystal structure of salt-tolerant glutaminase from Micrococcus luteus K-3 in the presence and absence of its product L-glutamate and its activator Tris.

PubMed

Yoshimune, Kazuaki; Shirakihara, Yasuo; Wakayama, Mamoru; Yumoto, Isao

2010-02-01

Glutaminase from Micrococcus luteus K-3 [Micrococcus glutaminase (Mglu); 456 amino acid residues (aa); 48 kDa] is a salt-tolerant enzyme. Our previous study determined the structure of its major 42-kDa fragment. Here, using new crystallization conditions, we determined the structures of the intact enzyme in the presence and absence of its product L-glutamate and its activator Tris, which activates the enzyme by sixfold. With the exception of a 'lid' part (26-29 aa) and a few other short stretches, the structures were all very similar over the entire polypeptide chain. However, the presence of the ligands significantly reduced the length of the disordered regions: 41 aa in the unliganded structure (N), 21 aa for L-glutamate (G), 8 aa for Tris (T) and 6 aa for both L-glutamate and Tris (TG). L-glutamate was identified in both the G and TG structures, whereas Tris was only identified in the TG structure. Comparison of the glutamate-binding site between Mglu and salt-labile glutaminase (YbgJ) from Bacillus subtilis showed significantly smaller structural changes of the protein part in Mglu. A comparison of the substrate-binding pocket of Mglu, which is highly specific for L-glutamine, with that of Erwinia carotovora asparaginase, which has substrates other than L-glutamine, shows that Mglu has a larger substrate-binding pocket that prevents the binding of L-asparagine with proper interactions.

COMPARISON OF SILICA IMMOBILIZED POLY-L-CYSTEINE AND 8-HYDROXYQUINOLINE FOR TRACE METAL CHELATION AND PRECONCENTRATION. (R826694C651)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

A Simplified Experimental Scheme for the Study of Mitosis.

ERIC Educational Resources Information Center

Gill, John

1980-01-01

A procedure is described for providing preparations of dividing cells from root apical meristems, requiring only inexpensive equipment and minimal experimental skill, and using 8-Hydroxyquinoline and Toluidene-blue as a chromosome stain. The method has been sucessfully tested in schools and yields permanent preparations of adequate quality for…

'Soya milk Tris-based phytoextender reduces apoptosis in cryopreserved buffalo (Bubalus bubalis) spermatozoa'.

PubMed

Mohan, R; Atreja, S K

2014-10-01

The objective of this study was to investigate the effect of newly developed soya milk Tris (SMT)-based phytoextender as an alternative to egg yolk Tris (EYT) extender used for cryopreservation of buffalo (Bubalus bubalis) spermatozoa on apoptosis. Fresh buffalo semen (control without dilution) was cryopreserved in conventional EYT (20% egg yolk v/v in Tris) and SMT (25% soya milk v/v in Tris) extender and used for the assessment of expression of apoptotic proteins. Proteins extracted from a total number of nine ejaculates from three individual buffalo bulls chosen at random were separated using SDS-PAGE followed by immunoblotting against caspase-8, caspase-9, caspase-3, poly(ADP-ribose)polymerase (PARP), cytochrome c and apoptosis inducing factor (AIF). In addition, fluorescence microscopy was used for the detection of mitochondrial membrane potential (JC-1 assay) and apoptotic cells (annexin V-FITC/PI assay). The results obtained clearly indicate the significant (p < 0.05) reduction in the expression of caspase-3 (27 kDa), caspase-8 (53 kDa), caspase-9 (50 kDa) precursor and cytochrome c (17 kDa) in semen cryopreserved in SMT extender in comparison with EYT extender. A non-significant (p > 0.05) reduction in expression of PARP-DNA-binding subunit (24 kDa) was observed in SMT extender. No expression of AIF was found in cryopreserved semen samples. A significant (p < 0.05) increase in the mean percentage of cells having high mitochondrial membrane potential and a non-significant (p > 0.05) decrease in late apoptotic cells (AN+/PI+) was observed in SMT extender when compared to EYT extender. The results demonstrated that cryopreservation of buffalo semen in SMT-based phytoextender can replace the traditional egg yolk extenders as it reduces the expression of apoptotic proteins maintaining high mitochondrial membrane potential and gives better protection to sperms in terms of its non-animal origin. © 2014 Blackwell Verlag GmbH.

Fertility results using bovine semen cryopreserved with extenders based on egg yolk and soy bean extract.

PubMed

van Wagtendonk-de Leeuw, A M; Haring, R M; Kaal-Lansbergen, L M; den Daas, J H

2000-07-01

Semen extenders containing components such as egg yolk and skim milk are difficult to standardize and they introduce the risk of microbial contamination. A well-defined extender not originating from animal tissues would present a valuable contribution to the AI industry. We evaluated the fertility of bovine semen cryopreserved with 3 different extenders: 1) TRIS-Standard, prepared at 2 local AI laboratories, containing 20% (v/v) pasteurized egg yolk, 2) TRIS-Concentrate, prepared by adding 20% (v/v) pasteurized egg yolk and 1:5 (v/v) nonpyrogenic water, and 3) Biociphos Plus, a soybean extract containing extender, prepared by adding 1:5 nonpyrogenic water. Ejaculates of 4 Holstein bulls were split into 3 aliquots and cryopreserved with the 3 extenders. Prior to this study, the semen dose-response curve for each of the 4 bulls was developed in a field trial by freezing the semen and randomly distributing the straws throughout the Netherlands for insemination. Optimal semen doses were thus established to detect the effect of extenders on fertility, evaluated by 56-day non-return rate (NR56), and by the estimated conception rate and the calving rate, given a conception. We used the multiphasic model developed by Grossman et al. (7). A total of 22,246 first and second inseminations were recorded. The NR56 ranged among bulls from 67.0 to 70.1% for Tris-Standard, from 67.5 to 69.9% for Tris-Concentrate and from 60.2 to 66.7% for Biociphos Plus. No significant differences in NR56 were detected between Tris-Standard and Tris-Concentrate (P=0.54), whereas Biociphos Plus resulted in a significantly lower NR56 than Tris-Standard and Tris-Concentrate (P<0.05). Estimated conception rate was 72.1, 73.6 and 69.6% and estimated calving rate, given a conception was 80.6, 78.3 and 77.1 for Tris-Standard, Tris-Concentrate and Biociphos Plus, respectively. These results indicate that 1) semen extended with a custom made TRIS-Concentrate can be succesfully used in the field resulting in comparable fertility with Tris-Standard; 2) semen extended with Biociphos Plus results in a significant reduction in the NR56; 3) extender source may affect both conception rate and calving rate, given a conception, i.e., extrinsic and intrinsic sperm factors (4).

AN/ALQ-135 tail warning system follow-on operational test and evaluation

NASA Astrophysics Data System (ADS)

Jenkins, V. M.

1981-11-01

This is a study of the reliability and maintainability of the tail warning system (TWS) AN/ALQ-153. This TWS is a solid state pulsed Doppler radar designed to provide warning and initiate countermeasures against threats attacking from the tail of B-52G/H aircraft.

Synthesis, Characterization, and Antibacterial Studies of Mixed Ligand Dioxouranium Complexes with 8-Hydroxyquinoline and Some Amino Acids

PubMed Central

Patil, Sunil S.; Thakur, Ganesh A.; Shaikh, Manzoor M.

2011-01-01

Mixed ligand complexes of dioxouranium (VI) of the type [UO2(Q)(L)·2H2O] have been synthesized using 8-hydroxyquinoline (HQ) as a primary ligand and amino acids (HL) such as L-threonine, L-tryptophan, and L-isoleucine as secondary ligands. The metal complexes have been characterized by elemental analysis, electrical conductance, magnetic susceptibility measurements, and spectral and thermal studies. The electrical conductance studies of the complexes indicate their nonelectrolytic nature. Magnetic susceptibility measurements revealed diamagnetic nature of the complexes. Electronic absorption spectra of the complexes show intraligand and charge transfer transitions, respectively. Bonding of the metal ion through N- and O-donor atoms of the ligands is revealed by IR studies, and the chemical environment of the protons is confirmed by NMR studies. The thermal analysis data of the complexes indicate the presence of coordinated water molecules. The agar cup and tube dilution methods have been used to study the antibacterial activity of the complexes against the pathogenic bacteria S. aureus, C. diphtheriae, S. typhi, and E. coli. PMID:22389843

76 FR 53451 - 2-(Hydroxymethyl)-2-nitro-1,3-propanediol (Tris Nitro); Amendments To Terminate Uses for Certain...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-26

.../ polymer emulsions; Specialty industrial products. 464-658 Tris Nitro \\TM\\ Brand of The Dow Chemical... emulsions; Specialty nitromethane. industrial products. 464-663 Tris Nitro\\TM\\ Brand of The Dow Chemical Company Use in paints, emulsions and 50% Aqueous Tris thickener solutions; Use in (hydroxymethyl...

Organometallic complexes of bulky, optically active, C 3-symmetric tris(4 S-isopropyl-5,5-dimethyl-2-oxazolinyl)phenylborate (To P*)

DOE PAGES

Xu, Songchen; Magoon, Yitzhak; Reinig, Regina R.; ...

2015-07-16

A bulky, optically active monoanionic scorpionate ligand, tris(4S-isopropyl-5,5-dimethyl-2-oxazolinyl)phenylborate (To P*), is synthesized from the naturally occurring amino acid l-valine as its lithium salt, Li[To P*] (1). That compound is readily converted to the thallium complex Tl[To P*] (2) and to the acid derivative H[To P*] (3). Group 7 tricarbonyl complexes To P*M(CO) 3 (M = Mn (4), Re (5)) are synthesized by the reaction of MBr(CO) 5 and Li[To P*] and are crystallographically characterized. The ν CO bands in their infrared spectra indicate that π back-donation in the rhenium compounds is greater with To P* than with non-methylated tris(4S-isopropyl-2-oxazolinyl)phenylborate (Tomore » P). The reaction of H[To P*] and ZnEt 2 gives To P*ZnEt (6), while To P*ZnCl (7) is synthesized from Li[To P*] and ZnCl 2. The reaction of To P*ZnCl and KOtBu followed by addition of PhSiH 3 provides the zinc hydride complex To P*ZnH (8). In this study, compound 8 is the first example of a crystallographically characterized optically active zinc hydride. We tested its catalytic reactivity in the cross-dehydrocoupling of silanes and alcohols, which provided Si-chiral silanes with moderate enantioselectivity.« less

Organometallic complexes of bulky, optically active, C 3-symmetric tris(4 S-isopropyl-5,5-dimethyl-2-oxazolinyl)phenylborate (To P*)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Songchen; Magoon, Yitzhak; Reinig, Regina R.

A bulky, optically active monoanionic scorpionate ligand, tris(4S-isopropyl-5,5-dimethyl-2-oxazolinyl)phenylborate (To P*), is synthesized from the naturally occurring amino acid l-valine as its lithium salt, Li[To P*] (1). That compound is readily converted to the thallium complex Tl[To P*] (2) and to the acid derivative H[To P*] (3). Group 7 tricarbonyl complexes To P*M(CO) 3 (M = Mn (4), Re (5)) are synthesized by the reaction of MBr(CO) 5 and Li[To P*] and are crystallographically characterized. The ν CO bands in their infrared spectra indicate that π back-donation in the rhenium compounds is greater with To P* than with non-methylated tris(4S-isopropyl-2-oxazolinyl)phenylborate (Tomore » P). The reaction of H[To P*] and ZnEt 2 gives To P*ZnEt (6), while To P*ZnCl (7) is synthesized from Li[To P*] and ZnCl 2. The reaction of To P*ZnCl and KOtBu followed by addition of PhSiH 3 provides the zinc hydride complex To P*ZnH (8). In this study, compound 8 is the first example of a crystallographically characterized optically active zinc hydride. We tested its catalytic reactivity in the cross-dehydrocoupling of silanes and alcohols, which provided Si-chiral silanes with moderate enantioselectivity.« less

Tris-base buffer: a promising new inhibitor for cancer progression and metastasis.

PubMed

Ibrahim-Hashim, Arig; Abrahams, Dominique; Enriquez-Navas, Pedro M; Luddy, Kim; Gatenby, Robert A; Gillies, Robert J

2017-07-01

Neutralizing tumor external acidity with oral buffers has proven effective for the prevention and inhibition of metastasis in several cancer mouse models. Solid tumors are highly acidic as a result of high glycolysis combined with an inadequate blood supply. Our prior work has shown that sodium bicarbonate, imidazole, and free-base (but not protonated) lysine are effective in reducing tumor progression and metastasis. However, a concern in translating these results to clinic has been the presence of counter ions and their potential undesirable side effects (e.g., hypernatremia). In this work, we investigate tris(hydroxymethyl)aminomethane, (THAM or Tris), a primary amine with no counter ion, for its effects on metastasis and progression in prostate and pancreatic cancer in vivo models using MRI and bioluminescence imaging. At an ad lib concentration of 200 mmol/L, Tris effectively inhibited metastasis in both models and furthermore led to a decrease in the expression of the major glucose transporter, GLUT-1. Our results also showed that Tris-base buffer (pH 8.4) had no overt toxicity to C3H mice even at higher doses (400 mmol/L). In conclusion, we have developed a novel therapeutic approach to manipulate tumor extracellular pH (pHe) that could be readily adapted to a clinical trial. © 2017 The Authors. Cancer Medicine published by John Wiley & Sons Ltd.

Swelling kinetics of spray-dried chitosan acetate assessed by magnetic resonance imaging and their relation to drug release kinetics of chitosan matrix tablets.

PubMed

Huanbutta, Kampanart; Sriamornsak, Pornsak; Limmatvapirat, Sontaya; Luangtana-anan, Manee; Yoshihashi, Yasuo; Yonemochi, Etsuo; Terada, Katsuhide; Nunthanid, Jurairat

2011-02-01

Magnetic resonance imaging (MRI) was used to assess in situ swelling behaviors of spray-dried chitosan acetate (CSA) in 0.1N HCl, pH 6.8 and pH 5.0 Tris-HCl buffers. The in vitro drug releases from CSA matrix tablets containing the model drugs, diclofenac sodium and theophylline were investigated in all media using USP-4 apparatus. The effect of chitosan molecular weight, especially in pH 6.8 Tris-HCl, was also studied. In 0.1N HCl, the drug release from the matrix tablets was the lowest in relation to the highest swelling of CSA. The swelling kinetics in Tris-HCl buffers are Fickian diffusion according to their best fit to Higuchi's model as well as the drug release kinetics in all the media. The high swelling rate (k(s)(')) was found to delay the drug release rate (k'). The linear relationship between the swelling and fractions of drug release in Tris-HCl buffers was observed, indicating an important role of the swelling on controlling the drug release mechanism. Additionally, CSA of 200 and 800 kDa chitosan did not swell in pH 6.8 Tris-HCl but disintegrated into fractions, and the drug release from the matrix tablets was the highest. Copyright © 2010 Elsevier B.V. All rights reserved.

Long-term preservation of chilled canine semen: effect of commercial and laboratory prepared extenders.

PubMed

Iguer-ouada, M; Verstegen, J P

2001-01-15

The present study was conducted to evaluate chilled semen conservation over time in 3 commercial and 4 laboratory prepared extenders, including a new Tris-glucose extender. The beneficial effect of adding egg yolk to these media was also analyzed. The effects of these extenders on motility and acrosome reaction were characterized objectively using a computer-aided semen analyzer and the chlortetracycline staining, respectively. No significant differences were observed when comparing the different commercial extenders without egg yolk, but addition of egg yolk improved all motility parameters significantly (preservation of 50% of motility was observed at 3.2+/-1, 2.9+/-0.5, 2.3+/-0.5, 8.5+/-0.2, 5.4+/-1.1, 5.2+/-0.4 d, for Biladyl, green extender and fresh-phos extenders without and with egg yolk, respectively). Motility parameters were best preserved in egg yolk supplemented Biladyl extender with a mean percentage of 86.3+/-10.5 motile spermatozoa after 7 d at 4 degrees C. Efficacy of egg yolk-supplemented commercial extenders on sperm motility at 4 degrees C was (in decreasing order) as follows: Biladyl > green extender > fresh-phos. However, high quality motility and the percentage of motile spermatozoa were highest with some of the laboratory prepared extenders: a 50% conservation rate of motile spermatozoa was observed following the use of supplemented egg yolk extenders. These are classified in decreasing order as follows: Tris-glucose (13+/-1 d) > Tris-fructose (9.7+/-0.6) > EDTA (4.+/-0.6 d) > Tris-bes (3.6+/-1.1 d). A low concentration of motile spermatozoa was still observed in the Tris-glucose egg yolk extender 16 d after collection, clearly demonstrating the importance of the medium and the beneficial effect of egg yolk on sperm motility of 4 degrees C chilled semen. Similar effects of extender were observed for acrosome reactions. Egg yolk clearly had a protective effect reducing acrosome reactions significantly in all media tested as follows: the highest acrosome losses were observed in the fresh-phos and EDTA extenders without egg yolk; the lowest rate was observed with Tris-glucose supplemented egg yolk extender. In conclusion, at 4 degrees C, egg yolk extender best-protected sperm motility parameters. Differences in osmolarity between the extenders in terms of substrate related to sperm metabolic activity may explain the optimal results obtained using egg yolk-supplemented Tris-glucose extender, which preserved motility and acrosome integrity in chilled dog semen. These results indicated that good quality dog spermatozoa could be preserved for up to 10 d.

Experimental Germ Tube Induction in Candida albicans: An Evaluation of the Effect of Sodium Bicarbonate on Morphogenesis and Comparison with Pooled Human Serum.

PubMed

Matare, Tapiwa; Nziramasanga, Pasipanodya; Gwanzura, Lovemore; Robertson, Valerie

2017-01-01

The potential of NaHCO 3 versus human serum to induce germ tube formation in Candida albicans was investigated. A total of 100 isolates were obtained from oral swabs of patients presenting with thrush. Approval for the study was granted by the Joint Research Ethics Committee (JREC/23/08). Confirmed C. albicans isolates by routine methods were tested for germ tube induction using 5 different concentrations of Tris-maleate buffered NaHCO 3 and Tris-maleate buffer control. Standard control strains included were C. albicans (ATCC 10231) and C. krusei (ATCC 6258). Microculture was done in 20  μ L inoculums on microscope slides for 3 hours at 37°C. The rate of germ tube formation at 10-minute intervals was determined on 100 isolates using the optimum 20 mM Tris-maleate buffered NaHCO 3 concentration. Parallel germ tube formation using human serum was done in test tubes. The optimum concentration of NaHCO 3 in Tris-maleate buffer for germ tube induction was 20 mM for 67% of isolates. Only 21% of isolates formed germ tubes in Tris-maleate buffer control. There was no significant difference in induction between human serum and Tris-maleate buffered NaHCO 3 . Tris-maleate buffered NaHCO 3 induced germ tube formation in C. albicans isolates at rates similar to human serum.

Heterotrophic Nature of the Cell-Free Protein-Synthesizing System from the Strict Chemolithotroph, Thiobacillus thiooxidans

PubMed Central

Amemiya, K.; Umbreit, W. W.

1974-01-01

A cell-free protein-synthesizing system prepared from the strict chemolithotroph, Thiobacillus thiooxidans, was similar to that of heterotrophs. The poly-U directed system had a temperature optimum of 37 C, but in the presence of spermidine (3 mM) the optimum shifted to 45 C. Although growth of the chemolithotroph occurs only in acid conditions, the pH optimum for the cell-free system was pH 7.2. The endogenous-directed activity in the presence or absence of spermidine was maximal at pH 7.8. Spermidine had a stimulatory effect; however, this effect was dependent on the magnesium and tris(hydroxymethyl)aminomethane (Tris) concentrations. At low Tris concentrations (10 mM), spermidine (3 to 5 mM) could completely replace magnesium. When the Tris concentration was increased (50 mM), spermidine could not replace magnesium. Supernatant and ribosomal fractions from T. thiooxidans were exchanged with those of Bacillus thuringiensis and Escherichia coli, and the ribosomal fraction from the chemolithotroph gave good to moderate stimulation when exchanged with the supernatant from the heterotrophs. On the other hand, the supernatant from T. thiooxidans gave good stimulation when mixed with ribosomes from B. thuringiensis but poor activity with ribosomes from E. coli. Both supernatant and ribosomal fractions prepared from stationary phase extracts of T. thiooxidans were inactive in the cell-free system. PMID:4590488

Synergistic cloud point extraction behavior of aluminum(III) with 2-methyl-8-quinolinol and 3,5-dichlorophenol.

PubMed

Ohashi, Akira; Tsuguchi, Akira; Imura, Hisanori; Ohashi, Kousaburo

2004-07-01

The cloud point extraction behavior of aluminum(III) with 8-quinolinol (HQ) or 2-methyl-8-quinolinol (HMQ) and Triton X-100 was investigated in the absence and presence of 3,5-dichlorophenol (Hdcp). Aluminum(III) was almost extracted with HQ and 4(v/v)% Triton X-100 above pH 5.0, but was not extracted with HMQ-Triton X-100. However, in the presence of Hdcp, it was almost quantitatively extracted with HMQ-Triton X-100. The synergistic effect of Hdcp on the extraction of aluminum(III) with HMQ and Triton X-100 may be caused by the formation of a mixed-ligand complex, Al(dcp)(MQ)2.

Characterization of time-resolved fluorescence response measurements for distributed optical-fiber sensing.

PubMed

Sinchenko, Elena; Gibbs, W E Keith; Davis, Claire E; Stoddart, Paul R

2010-11-20

A distributed optical-fiber sensing system based on pulsed excitation and time-gated photon counting has been used to locate a fluorescent region along the fiber. The complex Alq3 and the infrared dye IR-125 were examined with 405 and 780 nm excitation, respectively. A model to characterize the response of the distributed fluorescence sensor to a Gaussian input pulse was developed and tested. Analysis of the Alq3 fluorescent response confirmed the validity of the model and enabled the fluorescence lifetime to be determined. The intrinsic lifetime obtained (18.2±0.9 ns) is in good agreement with published data. The decay rate was found to be proportional to concentration, which is indicative of collisional deactivation. The model allows the spatial resolution of a distributed sensing system to be improved for fluorophores with lifetimes that are longer than the resolution of the sensing system.

8-aminoquinoline functionalized silica nanoparticles: a fluorescent nanosensor for detection of divalent zinc in aqueous and in yeast cell suspension.

PubMed

Rastogi, Shiva K; Pal, Parul; Aston, D Eric; Bitterwolf, Thomas E; Branen, A Larry

2011-05-01

Zinc is one of the most important transition metal of physiological importance, existing primarily as a divalent cation. A number of sensors have been developed for Zn(II) detection. Here, we present a novel fluorescent nanosensor for Zn(II) detection using a derivative of 8-aminoquinoline (N-(quinolin-8-yl)-2-(3 (triethoxysilyl)propylamino)acetamide (QTEPA) grafted on silica nanoparticles (SiNPs). These functionalized SiNPs were used to demonstrate specific detection of Zn(II) in tris-HCl buffer (pH 7.22), in yeast cell (Saccharomyces cerevisiae) suspension, and in tap water. The silane QTEPA, SiNPs and final product were characterized using solution and solid state nuclear magnetic resonance, Fourier transform infrared, ultraviolet-visible absorption spectroscopy, transmission electron microscopy, elemental analysis, thermogravimetric techniques, and fluorescence spectroscopy. The nanosensor shows almost 2.8-fold fluorescence emission enhancement and about 55 nm red-shift upon excitation with 330 ± 5 nm wavelength in presence of 1 μM Zn(II) ions in tris-HCl (pH 7.22). The presence of other metal ions has no observable effect on the sensitivity and selectivity of nanosensor. This sensor selectively detects Zn(II) ions with submicromolar detection to a limit of 0.1 μM. The sensor shows good applicability in the determination of Zn(II) in tris-HCl buffer and yeast cell environment. Further, it shows enhancement in fluorescence intensity in tap water samples.

Corrigendum to "The partial molal volume and compressibility of Tris and Tris-HCl in water and 0.725 m NaCl as a function of temperature," [Deep-Sea Res. I 104 (2015) 41-51

NASA Astrophysics Data System (ADS)

Rodriguez, Carmen; Huang, Fen; Millero, Frank J.

2016-08-01

The authors of Rodriguez et al. (2015) regret some incorrect values published in Tables 8 and 9. The values shown in Table 8 for V bar 0 and κ bar 0 of Tris-HCl in 0.725 m NaCl, and the values shown in Table 9 for ΔV and Δκ in 0.725 m NaCl were from an earlier calculation that was later revised. The correct values are provided below. Importantly, all other values printed in the manuscript are correct (e.g., coefficients in Tables 5-7, Table 8, Eqs. (22)-(25)). The discussions and conclusions made in this paper are not affected by these changes. The authors would like to acknowledge Yui Takeshita of Stanford University for bringing this to our attention. We apologize for any inconvenience caused.

Infrared Spectrum and UV-Induced Photochemistry of Matrix-Isolated 5-Hydroxyquinoline.

PubMed

Kuş, Nihal; Sagdinc, Seda; Fausto, Rui

2015-06-18

The structure, infrared spectrum, and photochemistry of 5-hydroxyquinoline (5HQ) were studied by matrix isolation infrared spectroscopy, complemented by theoretical calculations performed at the DFT(B3LYP)/6-311++G(d,p) level of approximation. According to the calculations, the trans conformer of 5HQ (with the OH group pointing to the opposite direction of the pyridine ring of the molecule) is more stable than the cis form (by ∼8.8 kJ mol(-1)). The main factors determining the relative stability of the two conformers were rationalized through natural bond orbital (NBO) and charge density analyses. The compound was trapped in solid nitrogen at 10 K, and its infrared spectra registered and interpreted, showing the sole presence in the matrix of the more stable trans conformer. Broadband in situ UV irradiations (λ ≥ 288 nm and λ ≥ 235 nm) allowed for the observation of different chemical transformations, which started by excitation to the S1 state of 5HQ, followed by homolytic cleavage of the O-H bond, and subsequent reattachment of the H atom to the 5HQ radical to form quinolin-5(6H)-one and quinolin-5(8H)-one. The first of these two quinolinones was found to convert to open-ring isomeric ketenes, especially when irradiation was performed at higher energy, whereas the second is rather stable under the used experimental conditions. As a whole, the observed photochemistry of matrix-isolated 5HQ closely matches those previously reported for phenol and thiophenol. A detailed mechanistic interpretation for the observed photochemical processes is here proposed, which received support from time-dependent DFT calculations.

An artificial guanine that binds cytidine through the cooperative interaction of metal coordination and hydrogen bonding.

PubMed

Mancin, Fabrizio; Chin, Jik

2002-09-18

Cd(II) complex of L binds selectively to cytidine in DMSO with an equilibrium constant of 117 M-1 (where LH is 2-aminomethyl-8-hydroxyquinoline). In contrast, the Zn(II) complex of L does not bind appreciably to any of the four nucleobases under the same condition used for the Cd(II) complex.

MODEL FOR NON-EQUILIBRIUM BINDING AND AFFINITY CHROMATOGRAPHY WITH CHARACTERIZATION OF 8-HYDROXYQUINOLINE IMMOBILIZED ON CONTROLLED PORE GLASS USING A FLOW INJECTION SYSTEM WITH A PACKED MICRO-COLUMN. (R826694C651)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Intermolecular interactions in the solid state structures of neutral and N-protonated 5-alkoxymethyl-8-hydroxyquinolines

NASA Astrophysics Data System (ADS)

Schulze, Mathias M.; Böhme, Uwe; Schwarzer, Anke; Weber, Edwin

2017-04-01

A series of five different alkoxymethyl substituted derivatives of 8-hydroxyquinoline was synthesised both in protonated (1a-1e) and neutral (2a-2e) form. The alkoxymethyl groups are MeO (1a, 2a), EtO (1b, 2b), n-PrO (1c, 2c), iso-PrO (1d, 2d), n-BuO (1e, 2e). The compounds were characterised by single crystal X-ray diffraction and spectroscopic methods. Hirshfeld surface analysis was performed to analyse the crystal packing quantitatively. Topological analysis of the electron density distribution delivers information about the strength of the hydrogen bonds. The overall results reveal a main difference between the charged (1a-1d) and uncharged (2a-2e) compounds in the orientation of the hydroxyl group resulting in a different cyclic dimer formation. In both cases the structures are dominated by hydrogen bonding (1a-1d: Osbnd H⋯Cl, Nsbnd H⋯Cl and 2a-2e: Osbnd H⋯N). Furthermore, all crystal structures show π involved interactions though taking only a minor part in the packing of the molecules.

Iron chelating ligand for iron overload diseases.

PubMed

Ozbolat, G; Tuli, A

2018-01-01

Iron overloads are a serious clinical condition in the health of humans and are therefore a key target in drug development. In this study, iron(III) complex of 8-hydroxyquinoline-5 sulphonic acid was synthesized and structurally characterized in its solid state and solution state by FT-IR, UV-Vis, elemental analysis, magnetic susceptibility and 1H-NMR. The catalase activities of complex were investigated. It was showed that the complex has the catalase activity. It is suggested that this type of complex may constitute a new and interesting basis for the future search for new and more potential drugs. The electrochemical behaviour patterns of the ligand and complex were examined as supporting electrolyte and platinum electrode for cyclic voltammetry. The electrochemistry studies showed that the reductions in free ligand and complex take place differently.The cytotoxicity was evaluated by MTT assay. The complex exhibited a very high cytotoxic activity and showed a cytotoxic effect that was much better than that of the ligand.The observed cytotoxicity could be pursued to obtain a potential drug. These results indicate that using the 8-hydroxyquinoline-5 sulphonic acid for this aim in further studies is appropriate (Tab. 1, Fig. 4, Ref. 18). Text in PDF www.elis.sk.

Luminescence of five-coordinated nickel(ii) complexes with substituted-8-hydroxyquinolines and macrocyclic ligands.

PubMed

Santana, M Dolores; García-Bueno, Rocío; García, Gabriel; Pérez, José; García, Luis; Monge, Miguel; Laguna, Antonio

2010-02-21

A series of heteroleptic quinolinolate pentacoordinated nickel(ii) complexes, [Ni(mcN(3))(R(1),R(2),R(3)-8-hq)](PF(6)), were synthesized and characterized by spectroscopic methods. Single-crystal X-ray diffraction studies for [(Me(3)-mcN(3))Ni(N,O-2-CN-8-hq)][PF(6)] (6a), [(Me(4)-mcN(3))Ni(N,O-8-hq)][PF(6)] (2b) and [(Me(4)-mcN(3))Ni(N,O-5,7-I(2)-8-hq)][PF(6)] (5b) indicate that these complexes consist of a square-pyramidal ligand arrangement containing one chelating quinolinolate and one macrocyclic ligand (mcN(3)). Variation of the substituents on quinolinolate ligands imposes obvious electronic or structural effects on the nickel atom. These chromophores absorb moderately in the visible region and emit in the yellowish-green spectral region from a quinolinolate-centered intraligand charge-transfer excited state. The emission maxima are in the range 520-548 nm, with quantum yields between 0.11 and 1.63%, in deoxygenated organic solvents at room temperature. TD-DFT calculations allow exploration of the photophysical properties of complex [(Me(4)-mcN(3))Ni(N,O-8-hq)][PF(6)] and reveal the influence of the quinolinolate ligand on the HOMO/LUMO energies and oscillator strengths.

Preferential deprotonation and conformational stability of dicarboxylic acids: A packing effect

NASA Astrophysics Data System (ADS)

Barooah, Nilotpal; Singh, W. Marjit; Baruah, Jubaraj B.

2008-03-01

Crystal structures of a series of salts of (6-carboxymethyl-1,3,5,7-tetraoxo-3,5,6,7-tetrahydro-1 H-pyrrolo[3,4- f]isoindol-2-yl)-acetic acid ( 1) and 2-carboxymethyl-1,3-dioxo-2,3-dihydro-1 H-isoinodole-5-carboxylic acid ( 2) with different polynuclear nitrogen containing heterocyclic compounds, namely, quinoline, 1,10-phenanthroline and 8-hydroxyquinoline are determined. In the case of salt of 1 with quinolinium and 1,10-phenanthrolinium cations syn disposition between the carboxylate anion and carboxylic acid groups is observed; whereas in the case of the 8-hydroxyquinolinium salt of 1, it is the anti disposition. It is also found that the solid state structure of 1,10-phenanthrolinium salt of 2 has deprotonation at the aromatic end, whereas in 8-hydroxy-quinolinium salt of 2 is formed by deprotonation of carboxylic acid group on the aliphatic side. The dicarboxylic acid 2 forms 1:2 co-crystals with quinoline. From crystallographic study it is shown that the weak interactions become prominent in stabilising the observed conformers and also in stabilising specific deprotonated species.

Isolation of Protective Antigen from Anthrax Toxin by Preparative Isotachophoresis

DTIC Science & Technology

1982-06-14

caosule of polymerized D-olutamic acid which inhibits phago- cytosis and allows the bacillus to establish an infectious focus and elaborate a tripartite...The terminating buffer Tris-c- aminocaproate (Tris-EACA), pH 8.4, was used in the upper electrode (cathode) chamber and in the column. fteen ml of toxin

DEVELOPMENT OF A SMALL CHAMBER METHOD FOR SVOC SINK EFFECT STUDY

EPA Science Inventory

This paper describes the details of the improved chamber system and reports the sink effect study for organophosphorus flame retardants (OP-FRs), including tris(2-chloroethyl) phosphate(TCEP), tris(1-chlor-2-propyl) phosphate (TCPP) and tris(1,3-dichloro-2-propyl) phosphate (TDC...

In vitro embryo production in camel (Camelus dromedarius) from in vitro matured oocytes fertilized with epididymal spermatozoa stored at 4 degrees C.

PubMed

Wani, N A

2009-03-01

Experiments were conducted to study the effect of storing epididymal spermatozoa, in tris-tes- and tris-lactose egg yolk extenders, on their fertilizing ability and subsequent in vitro embryo development. Ovaries and testes were collected from a local slaughterhouse in normal saline solution (NSS) at 37 degrees C and on ice (0-1 degrees C), respectively. Cumulus oocyte complexes (COCs) aspirated from the follicles were randomly distributed to 4-well culture plates (20-25COCs/well) containing 500 microL of maturation medium and cultured at 38.5 degrees C in an atmosphere of 5% CO(2) in air for 36 h. Spermatozoa were collected from the cauda epididymides in syringes containing 2-3 mL of either tris-tes- or tris-lactose egg yolk extender. They were cooled down slowly and stored at refrigeration (4 degrees C) temperature. The spermatozoa were evaluated for motility and used for IVF of IVM oocytes on the day of collection and after 2, 4, 6 and 8 days of storage. On the day of IVF, spermatozoa were prepared by the swim up technique and both spermatozoa and oocytes were co-incubated at 38.5 degrees C in a humidified atmosphere of 5% CO(2) in air for 15-16 h. Presumptive zygotes were either fixed and stained with Hoechst 33342 for evaluation of fertilization or were cultured in 500 microL of the culture medium at 38.5 degrees C in an atmosphere of 5% CO(2), 5% O(2) and 90% N(2) in air. There was no significant difference (P>0.05) in the proportion of oocytes fertilized with spermatozoa stored in either of the two extenders for up to 8 days. The proportion of oocytes that cleaved (43-60%) and those that developed to blastocysts (14-21%) did not show any difference (P>0.05) either, when spermatozoa from different days of storage were used. First cleavage was observed as early as 16 h after IVF, early blastocysts had developed by day 4, expanded blastocysts after day 5 and hatching of blastocysts started after day 6 of culture. It may be concluded that dromedary epididymal spermatozoa survive in storage for at least 8 days in tris-lactose- and tris-tes egg yolk diluents at 4 degrees C. These spermatozoa maintain fertilizing ability and may be suitable for use in IVF and other assisted reproductive procedures.

ESR study of the molecular orientation and dynamics of stable organic radicals included in the 1-D organic nanochannels of 2,4,6-tris-4-(chlorophenoxy)-1,3,5-triazine.

PubMed

Kobayashi, Hirokazu; Asaji, Tetsuo; Tani, Atsushi

2012-03-01

The molecular orientation and dynamics of the organic stable radicals such as 2,2,6,6-tetramethyl-1-piperidinyl-1-oxyl (TEMPO) or 4-hydroxy-TEMPO (TEMPOL) included in the one-dimensional (1-D) organic nanochannels of 2,4,6-tris-4-(chlorophenoxy)-1,3,5-triazine (CLPOT) were investigated by examining the inclusion compounds (ICs) diluted by the co-inclusion of non-radicals using ESR spectroscopy. Spectral simulation showed that the axial rotation of TEMPO or TEMPOL molecules is excited in the nanochannels with activation energies of 8 and 7 kJ mol(-1) , respectively. The rotation axis was estimated to be tilted towards the principal x direction in the axis system of the g-tensor of the respective radicals. This is quite different from that for similar ICs in the nanochannels of tris(o-phenylenedioxy)cyclotriphosphazene (TPP), in which the radicals are axially rotating around the principal axis y of the g-tensor. The difference is attributed to the larger nanospace of the CLPOT nanochannels. Copyright © 2012 John Wiley & Sons, Ltd.

DNA polymerases in the rat pituitary gland. Effect of oestrogens and sulpiride.

PubMed

Jahn, G A; Kalbermann, L E; Machiavelli, G; Szijan, I; Burdman, J A

1980-06-01

Changes in the activity of DNA polymerase and [3H]thymidine incorporation into the DNA of the anterior pituitary gland were studied in oestrogenized male and pregnant rats. The activities of DNA polymerases alpha and beta, extracted in Tris--HCl or in sodium phosphate buffer were characterized according to their optimum pH and sensitivity to N-ethyl-maleimide. In the Tris-soluble fraction DNA polymerase activity is almost exclusively alpha, while in the phosphate soluble fraction it is a mixture of alpha and beta. The administration of oestrogens to male rats increases [3H]thymidine incorporation and enhances the activity of DNA polymerases in the Tris-soluble fraction, while the activity of the phosphate-soluble enzyme does not change. Sulpiride administration results in a further increment of [3H]thymidine incorporation and of DNA polymerase activity in the Tris-soluble fraction. In pregnant rats sulpiride also produces an increment of DNA polymerase activity only in the Tris-soluble fraction. Thus, the activity of the Tris-soluble fraction from APG behaves as DNA polymerase alpha. This activity changes in parallel with [3H]thymidine incorporation into DNA which is an indication of cell proliferation in the gland. This is discussed with respect to a negative feedback mechanism between intracellular prolactin concentration and DNA synthesis in the APG.

Comparison of Air Sampling Methods for Organophosphate Flame Retardants in Small Environmental Chambers

EPA Science Inventory

Organophosphorus flame retardants (OPFRs), such as tris(2-chloroethyl) phosphate (TCEP), tris(1-chlor-2-propyl) phosphate (TCPP), and tris(1,3-dichloro-2-propyl) phosphate (TDCPP), used as additives in industrial and consumer products are being detected in indoor air, house dust,...

International Traffic in Arms Regulations (ITAR), (22 CFR 120-130)

DTIC Science & Technology

1996-06-01

Butadienenitrileoxide (BNO); (6) Catocene, N-butyl- ferrocene and other ferrocene derivatives; (7) 3-nitraza-l,5 pentane diisocyanate; (8) Bis(2,2...Tris-l-(2-methyl)aziridinyl phosphine oxide (MAPO), bis(2-methyl aziridinyl) 2-(2-hydroxypropanoxy) propylamino phosphine oxide (BOBBA 8), and...other MAPO derivatives; (22) Bis(2-methyl aziridinyl) methylamino phosphine oxide (methyl BAPO); (23) Organo-metallic coupling agents, specifi

Simultaneous production of rhamnolipids, 2-alkyl-4-hydroxyquinolines, and phenazines by clinical isolates of Pseudomonas aeruginosa.

PubMed Central

Smeal, B C; Bender, L; Jungkind, D L; Hastie, A T

1987-01-01

Of 72 clinical isolates of Pseudomonas aeruginosa examined for simultaneous production of secondary metabolites, 86% produced 2-alkyl-4-hydroxyquinolines, 75% produced rhamnolipids, and 58% produced phenazines, including pyocyanin. Whereas isolates producing two or one constituted smaller groups, 39% released all three metabolites. Metabolite production did not appear to influence site of infection. PMID:3112182

Synthesis, structural elucidation, solvatochromism and spectroscopic properties of some azo dyes derived from 6-chloro-4-hydroxyquinoline-2(1H)-one

NASA Astrophysics Data System (ADS)

Rufchahi, E. O. Moradi; Gilani, A. Ghanadzadeh; Taghvaei, V.; Karimi, R.; Ramezanzade, N.

2016-03-01

Malondianilide (I) derived from p-chloroaniline was cyclized to 6-chloro-4-hydroxyquinoline-2(1H)-one (II) in moderately good yield using polyphosphoric acid as catalyst. This compound was then coupled with some diazotized aromatic amines to give the corresponding azo disperse dyes 1-12. A systematic study of the effect of solvent, acid, base and pH upon the electronic absorption spectra of the dyes 1-12 was carried out. In DMSO, DMF, CH3CN, CHCl3, EtOH and acidic media (CH3COOH, acidified EtOH) these dyes that theoretically may be involved in azo-hydrazone tautomerism have been detected only as hydrazone tautomers T1 and T2. The acidic dissociation constants of the dyes were measured in 80 vol% ethanol-water solution at room temperature and ionic strength of 0.1. The results were correlated by the Hammett-type equation using the substituent constants σx.

40 CFR 721.10688 - Copper, chloro[tris(2-chloroethyl) phosphite-.kappa.P]-.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) phosphite-.kappa.P]-. 721.10688 Section 721.10688 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.10688 Copper, chloro[tris(2-chloroethyl) phosphite-.kappa.P]-. (a... copper, chloro[tris(2-chloroethyl) phosphite-.kappa.P]- (PMN P-13-221; CAS No. 24484-01-3) is subject to...

Purification of α-glucosidase from mouse intestine by countercurrent chromatography coupled with a reverse micelle solvent system.

PubMed

He, Kai; Zou, Zongyao; Hu, Yinran; Yang, Yong; Xiao, Yubo; Gao, Pincao; Li, Xuegang; Ye, Xiaoli

2016-02-01

Countercurrent chromatography coupled with a reverse micelle solvent was applied to separate α-glucosidase, which is stable at pH 6.0-8.8, 15-50°C. The separation conditions are as follows: stationary phase: pH 4.0 Tris-HCl buffer phase containing 50 mM Tris-HCl and 50 mM KCl; mobile phase A: isooctane containing 50 mM anionic surfactant sodium di(2-ethylhexyl)sulfosuccinate; mobile phase B: 50 mM Tris-HCl buffer containing 500 mM KCl (pH 8.0); In total, 25 mL (23.9 mg) crude enzyme was injected through the injection valve, the enzymatic reaction and sodium dodecylsulfate polyacrylamide gel electrophoresis results imply that the activity of purified α-glucosidase is 6.63-fold higher than that of the crude enzyme. Therefore, countercurrent chromatography coupled with a reverse micelle solvent is capable for protein separation and enrichment. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Highly Efficient White Organic Light Emitting Diodes Using New Blue Fluorescence Emitter.

PubMed

Kim, Seungho; Kim, Beomjin; Lee, Jaehyun; Yu, Young-Jun; Park, Jongwook

2015-07-01

Two different emitting compounds, 1-[1,1';3',1"]Terphenyl-5'-yl-6-(10-[1,1';3',1"]terpheny-5'-yl- anthracen-9-yl)-pyrene (TP-AP-TP) and Poly-phenylene vinylene derivative (PDY 132) were used to white OLED device. By incorporating adjacent blue and yellow emitting layers in a multi-layered structure, highly efficient white emission has been attained. The device was fabricated with a hybrid configuration structure: ITO/PEDOT (40 nm)/PDY-132 (8-50 nm)/ NPB (10 nm)/TP-AP-TP (30 nm)/Alq3 (20 nm)/LiF (1 nm)/Al (200 nm). After fixing TP-AP-TP thickness of 30 nm by evaporation, PDY-132 thickness varied with 8, 15, 35, and 50 nm by spin coating in device. The luminance efficiency of the white devices at 10 mA/cm2 were 2.93 cd/A-6.55 cd/A. One of white devices showed 6.55 cd/A and white color of (0.290, 0.331).

ARPA/NRL X-Ray Laser Program

DTIC Science & Technology

1977-04-01

aluminum ) is photographed using a double-pinhole x-ray camera. Fig. 21 shows , 45 —.— LASER >1.0keV LASER >1.5keV 100 /im Fig. 21 — Pinhole x...i ’ 1 i 6.0 7.0 Ml) 8.0 Fig. 29 — Comparison of computed spectral line intensities of aluminum and that obtained from the experiment 56...Mg-target used in this partic- ular exposure contained aluminum and carbon as impurities; the AJ6II 3-3p 1P - 3s2 1S line at 1670.8 A and the CIV 2p

Organophosphorus flame retardants and plasticizers in air from various indoor environments.

PubMed

Marklund, Anneli; Andersson, Barbro; Haglund, Peter

2005-08-01

Eleven organophosphorus compounds (OPs) that are used as plasticizers and flame retardants were analysed in duplicate samples of indoor air from 17 domestic and occupational environments. Solid-phase extraction (SPE) columns were used as adsorbents and analysis was performed using GC with a nitrogen phosphorus selective detector. The total amounts of OPs in the air samples ranged between 36 and 950 ng m(-3); tris(chloropropyl) phosphate (TCPP) and tris(2-chloroethyl) phosphate (TCEP) being the most abundant (0.4 to 730 ng m(-3)), followed by tributyl phosphate (0.5-120 ng m(-3)). Public buildings tended to have about 3-4 times higher levels of OPs than domestic buildings. The relative amounts of individual OPs varied between the sites and generally reflected the building materials, furniture and consumer products used in the sampled environments. Potential sources of these compounds include, inter alia, acoustic ceilings, upholstered furniture, wall coverings, floor polish and polyvinylchloride floor coverings. A correlation was observed between the TCEP concentrations in the air in the sampled environments and previously reported concentrations in dust, but no such correlation was seen for the heavier and less volatile tris(2-butoxyethyl) phosphate (TBEP). Based on estimated amounts of indoor air inhaled and dust ingested, adults and children in the sampled environments would be exposed to up to 5.8 microg kg(-1) day(-1) and 57 microg kg(-1) day(-1) total OPs, respectively.

Analysis of surface tris (2,3-dibromopropyl) phosphate on chlorobutyl rubber SCAPE suits. [flame retardant coatings

NASA Technical Reports Server (NTRS)

Schehl, T. A.; Bennett, H. D.; Bryan, C. J.; Bright, C. W.

1978-01-01

Tris (2,30-dibromopropyl) phosphate was used to confer flame retardant properties on butyl rubber formulations used in protective clothing such as the self-contained atmospheric protective ensembles (SCAPE suits) worn at Kennedy Space Center in support of Apollo, Skylab, and Apollo-Soyuz missions since 1966. Because tris (2,3-dibromopropyl) phosphate is mutagenic, surface concentrations of the compound in SCAPE suits were investigated as were as potential methods of removing or isolating it. Analytical procedures for determining surface concentrations of the tris compound on non-porous materials are described. Soap-and-water washing is the most efficient method of removing the compound from fabricated SCAPE suits and unused material.

Dynamic spin filtering at the Co/Alq3 interface mediated by weakly coupled second layer molecules.

PubMed

Droghetti, Andrea; Thielen, Philip; Rungger, Ivan; Haag, Norman; Großmann, Nicolas; Stöckl, Johannes; Stadtmüller, Benjamin; Aeschlimann, Martin; Sanvito, Stefano; Cinchetti, Mirko

2016-08-31

Spin filtering at organic-metal interfaces is often determined by the details of the interaction between the organic molecules and the inorganic magnets used as electrodes. Here we demonstrate a spin-filtering mechanism based on the dynamical spin relaxation of the long-living interface states formed by the magnet and weakly physisorbed molecules. We investigate the case of Alq3 on Co and, by combining two-photon photoemission experiments with electronic structure theory, show that the observed long-time spin-dependent electron dynamics is driven by molecules in the second organic layer. The interface states formed by physisorbed molecules are not spin-split, but acquire a spin-dependent lifetime, that is the result of dynamical spin-relaxation driven by the interaction with the Co substrate. Such spin-filtering mechanism has an important role in the injection of spin-polarized carriers across the interface and their successive hopping diffusion into successive molecular layers of molecular spintronics devices.

Dynamic spin filtering at the Co/Alq3 interface mediated by weakly coupled second layer molecules

PubMed Central

Droghetti, Andrea; Thielen, Philip; Rungger, Ivan; Haag, Norman; Großmann, Nicolas; Stöckl, Johannes; Stadtmüller, Benjamin; Aeschlimann, Martin; Sanvito, Stefano; Cinchetti, Mirko

2016-01-01

Spin filtering at organic-metal interfaces is often determined by the details of the interaction between the organic molecules and the inorganic magnets used as electrodes. Here we demonstrate a spin-filtering mechanism based on the dynamical spin relaxation of the long-living interface states formed by the magnet and weakly physisorbed molecules. We investigate the case of Alq3 on Co and, by combining two-photon photoemission experiments with electronic structure theory, show that the observed long-time spin-dependent electron dynamics is driven by molecules in the second organic layer. The interface states formed by physisorbed molecules are not spin-split, but acquire a spin-dependent lifetime, that is the result of dynamical spin-relaxation driven by the interaction with the Co substrate. Such spin-filtering mechanism has an important role in the injection of spin-polarized carriers across the interface and their successive hopping diffusion into successive molecular layers of molecular spintronics devices. PMID:27578395

Dynamic spin filtering at the Co/Alq3 interface mediated by weakly coupled second layer molecules

NASA Astrophysics Data System (ADS)

Droghetti, Andrea; Thielen, Philip; Rungger, Ivan; Haag, Norman; Großmann, Nicolas; Stöckl, Johannes; Stadtmüller, Benjamin; Aeschlimann, Martin; Sanvito, Stefano; Cinchetti, Mirko

2016-08-01

Spin filtering at organic-metal interfaces is often determined by the details of the interaction between the organic molecules and the inorganic magnets used as electrodes. Here we demonstrate a spin-filtering mechanism based on the dynamical spin relaxation of the long-living interface states formed by the magnet and weakly physisorbed molecules. We investigate the case of Alq3 on Co and, by combining two-photon photoemission experiments with electronic structure theory, show that the observed long-time spin-dependent electron dynamics is driven by molecules in the second organic layer. The interface states formed by physisorbed molecules are not spin-split, but acquire a spin-dependent lifetime, that is the result of dynamical spin-relaxation driven by the interaction with the Co substrate. Such spin-filtering mechanism has an important role in the injection of spin-polarized carriers across the interface and their successive hopping diffusion into successive molecular layers of molecular spintronics devices.

Preparation of aluminum-magnesium alloy from magnesium oxide in RECl3-KCl-MgCl2 electrolyte by molten salts electrolysis method

NASA Astrophysics Data System (ADS)

Yang, Shaohua; Wu, Lin; Yang, Fengli; Li, Mingzhou; Hu, Xianwei; Wang, Zhaowen; Shi, Zhongning; Gao, Bingliang

Aluminum-magnesium alloys were prepared from magnesium oxide by molten salt electrolysis method. 10w%RECl3-63.5w%KCl-23.5w%MgCl2-3w%MgO was taken as electrolyte. The results showed that RE could be attained in aluminum-magnesium alloy, and it was proved that the RE was reduced directly by aluminum. Magnesium in the alloy was produced by electrolysis on cathode. The content of RE in the alloy was about 0.8wt %-1.2wt%, and the content of Mg in the alloy was lwt%˜6wt% with electrolytic times. The highest current efficiency was 81.3% with 0.8A/cm2 current density. The process of electrolysis was controlled together by electrochemical polarization and concentration polarization.

Isomorphism Within the Hexagonal Columnar Mesophase of Molecular and Macromolecular Self- and Co-Assembled Columns Containing Tapered Groups

DTIC Science & Technology

1994-06-30

benzyloxylbenzoic acid , their corresponding polymethacrylates , and of 4’- methyl (benzo- 15-crown-5)-3,4,5-tris[4-(n-dodecan- 1 -yloxy)benzyloxylbenzoate within...l-yloxy)benzyloxy]benzoic acid , of their corresponding polymethacrylates , and of 4’-methyl(benzo- 15-crown-5)-3,4,5-tris[4- (n-dodecan- 1-yloxy...benzyloxylbenzoic acid , of their corresponding polymethacrylates ,18a and of 4’-methyl(benzo-15-crown-5)-3,4,5-tris[4-(n-dodecan-l- yloxy)benzyloxy]benzoate 1 7

Dendrite-like Co3O4 nanostructure and its applications in sensors, supercapacitors and catalysis.

PubMed

Pang, Huan; Gao, Feng; Chen, Qun; Liu, Rongmei; Lu, Qingyi

2012-05-21

Dendrite-like Co(3)O(4) nanostructure, made up of many nanorods with diameters of 15-20 nm and lengths of 2-3 μm, has been successfully prepared by calcining the corresponding nanostructured Co-8-hydroxyquinoline coordination precursor in air. The Co(3)O(4) nanostructure was evaluated as an electrochemical sensor for H(2)O(2) detection and the results reveal that it has good linear dependence and high sensitivity to H(2)O(2) concentration changes. As an electrode material of a supercapacitor, it was found that the nanostructured Co(3)O(4) electrode exhibits high specific capacitance and long cycle life. The Co(3)O(4) nanostructure also has good catalytic properties and is steadily active for CO oxidation, giving 100% CO conversion at low temperatures. The multifunctional Co(3)O(4) nanostructure would be a promising functional nanomaterial applied in multi industrialized fields.

Synthesis and characterization of a new photoluminescent material, tris-[1-10 phenanthroline] aluminium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Rahul, E-mail: id-kumarrahul003@gmail.com; Bhargava, Parag; Dvivedi, Avanish

A new photoluminescent material namely tris-[1-10 Phenanthroline] Aluminium Al(Phen){sub 3} has been synthesized and characterized. This material was characterized by fourier transform infrared spectroscopy (FTIR),nuclear magnetic resonance (NMR),mass spectroscopy, thermal gravimetric analysis (TGA),ultraviolet-visible spectroscopy(UV) and photoluminescence (PL). This material shows thermal stability up to 300°C. This material showed absorption maxima at 352nm which may be attributed to the moderate energy (π–π{sup *}) transition. Photoluminescence spectra for this material showed the most intense peak at 423 nm and the time resolved photoluminescence spectra showed two life time components. The decay times of the first and second component were 1.4ns and 4.8 ns respectively.

Legacy and emerging organophosphοrus flame retardants in car dust from Greece: Implications for human exposure.

PubMed

Christia, Christina; Poma, Giulia; Besis, Athanasios; Samara, Constantini; Covaci, Adrian

2018-04-01

Organophosphorus flame retardants (PFRs) and emerging PFRs (ePFRs) are two groups of compounds used as replacements for brominated flame retardants (BFRs). They have already been detected in indoor dust (mainly in homes and offices). To date, few studies investigated the occurrence of FRs in car dust and the information of possible health risks is still limited. The present study reports on the investigation of the levels and profiles of eight target PFRs: tris(2-ethylhexyl) phosphate (TEHP), tris(2-chloroethyl) phosphate (TCEP), tris(2-butoxyethyl) phosphate (TBEP), triphenyl phosphate (TPHP), 2-ethylhexyl diphenyl phosphate (EHDPHP), tris(1-chloro-2-propyl) phosphate (TCIPP), tri cresyl phosphate (TCP), tris(1,3-dichloro-2-propyl) phosphate (TDCIPP) and four target ePFRs; 2,2-bis(chloromethyl)propane-1,3-diyltetrakis(2-chloroethyl)bisphosphate (V6), isodecyl diphenyl phosphate (iDDPHP), resorcinol bis(diphenylphosphate) (RDP) and bisphenol A-bis(diphenyl phosphate) (BDP) in car dust from Greece. The samples were collected from the interior of 25 private cars in Thessaloniki, Greece, with different years of manufacture (1997-2015) and continents of origin. After ultrasonic extraction and Florisil fractionation, the PFR analysis was carried out by GC-EI/MS, whereas the ePFRs were analyzed by LC-MS/MS. Levels of Σ 8 PFRs varied from 2000 to 190,000 ng g -1 , with mean and median concentrations of 20,000 and 11,500 ng g -1 , respectively. The concentrations of Σ 4 ePFRs ranged from 44 to 8700 ng g -1 , with mean and median values at 1100 and 190 ng g -1 , respectively. Estimations of human exposure showed that toddlers are more exposed than adults to both PFRs and ePFRs. Yet, the intake via dust ingestion and dermal absorption was several orders of magnitude lower than the corresponding reference doses. Copyright © 2017 Elsevier Ltd. All rights reserved.

Performance Enhancement of Organic Light-Emitting Diodes Using Electron-Injection Materials of Metal Carbonates

NASA Astrophysics Data System (ADS)

Shin, Jong-Yeol; Kim, Tae Wan; Kim, Gwi-Yeol; Lee, Su-Min; Shrestha, Bhanu; Hong, Jin-Woong

2016-05-01

Performance of organic light-emitting diodes was investigated depending on the electron-injection materials of metal carbonates (Li2CO3 and Cs2CO3 ); and number of layers. In order to improve the device efficiency, two types of devices were manufactured by using the hole-injection material (Teflon-amorphous fluoropolymer -AF) and electron-injection materials; one is a two-layer reference device ( ITO/Teflon-AF/Alq3/Al ) and the other is a three-layer device (ITO/Teflon-AF/Alq3/metal carbonate/Al). From the results of the efficiency for the devices with hole-injection layer and electron-injection layer, it was found that the electron-injection layer affects the electrical properties of the device more than the hole-injection layer. The external-quantum efficiency for the three-layer device with Li2CO3 and Cs2CO3 layer is improved by approximately six and eight times, respectively, compared with that of the two-layer reference device. It is thought that a use of electron-injection layer increases recombination rate of charge carriers by the active injection of electrons and the blocking of holes.

Improved stability and electrophoretic properties of preformed fluorescent cationic dye-DNA complexes in a taps-tetrapentylammonium buffer in agarose slab gels.

PubMed

Zeng, Z; Clark, S M; Mathies, R A; Glazer, A N

1997-10-01

High-resolution capillary electrophoresis sizing of preformed complexes of bis-intercalating fluorescent dyes with double-stranded DNA has been demonstrated using hydroxyethylcellulose and 3-[tris-(hydroxymethyl) methylamino]-1-propanesulfonic acid-tetrapentylammonium (Taps-NPe+4) buffers (S. M. Clark and R. A. Mathies, Anal. Chem. 69, 1355-1363, 1997). Such capillary electrophoresis separations were unattainable in conventional buffers containing other cations such as Tris+, Na+, and NH+4. We report here the behavior of preformed double-stranded DNA-dye complexes on agarose slab gel electrophoresis in 40 mM Taps-NPe+4, 1 mM H2EDTA, pH 8.2. Upon electrophoresis in this buffer (a) complexes formed at DNA base pairs:dye ratios ranging from 100:1 to 5:1 show the same mobility; (b) the half-lives of DNA-dye complexes with monointercalators are two- to threefold longer than those in commonly used Tris buffers; (c) there is little dye transfer between labeled and unlabeled DNA molecules; and (d) precise two-color sizing of preformed restriction fragment-dye complexes with fluorescent bisintercalators is achieved.

Occurrence and dry deposition of organophosphate esters in atmospheric particles over the northern South China Sea.

PubMed

Lai, Senchao; Xie, Zhiyong; Song, Tianli; Tang, Jianhui; Zhang, Yingyi; Mi, Wenying; Peng, Jinhu; Zhao, Yan; Zou, Shichun; Ebinghaus, Ralf

2015-05-01

Nine organophosphate esters (OPEs) in airborne particles were measured during a cruise campaign over the northern South China Sea (SCS) from September to October 2013. The concentration of the total OPEs (∑OPEs) was 47.1-160.9 pg m(-3), which are lower than previous measurements in marine atmosphere environments. Higher OPE concentrations were observed in terrestrially influenced samples, suggesting that OPE concentrations were significantly influenced by air mass transport. Chlorinated OPEs were the dominant OPEs, accounting for 65.8-83.7% of the ∑OPEs. Tris-(2-chloroethyl) phosphate (TCEP) was the predominant OPE compound in the samples (45.0±12.1%), followed by tris-(1-chloro-2-propyl) phosphates (TCPPs) (28.8±8.9%). Dry particle-bound deposition fluxes ranged from 8.2 to 27.8 ng m(-2) d(-1) for the ∑OPEs. Moreover, the dry deposition input of the ∑OPEs was estimated to be 4.98 ton y(-1) in 2013 in a vast area of northern SCS. About half of the input was found to relate to air masses originating from China. Copyright © 2015 Elsevier Ltd. All rights reserved.

Synthesis and Spectral Evaluation of Some Unsymmetrical Mesoporphyrinic Complexes

PubMed Central

Boscencu, Rica; Oliveira, Anabela Sousa; Ferreira, Diana P.; Ferreira, Luís Filipe Vieira

2012-01-01

Synthesis and spectral evaluation of new zinc and copper unsymmetrical mesoporphyrinic complexes are reported. Zn(II)-5-(4-acetoxy-3-methoxyphenyl)-10,15,20- tris-(4-carboxymethylphenyl)porphyrin, Zn(II)-5-[(3,4-methylenedioxy)phenyl]-10,15,20- tris-(4-carboxymethylphenyl)porphyrin, Cu(II)-5-(4-acetoxy-3-methoxyphenyl)-10,15,20- tris-(4-carboxymethylphenyl)porphyrin and Cu(II)-5-[(3,4-methylenedioxy)phenyl]-10,15,20- tris-(4-carboxymethylphenyl)porphyrin were synthesized using microwave-assisted synthesis. The complexes were characterized by elemental analysis, FT-IR, UV-Vis, EPR and NMR spectroscopy, which fully confirmed their structure. The spectral absorption properties of the porphyrinic complexes were studied in solvents with different polarities. Fluorescence emission and singlet oxygen formation quantum yields were evaluated for the compounds under study, revealing high yields for the zinc derivatives. The copper complexes are not emissive and only display residual capacity for singlet oxygen formation. PMID:22942693

Aminoacid N-substituted 1,4,7-triazacyclononane and 1,4,7,10-tetraazacyclododecane Zn2+, Cd2+ and Cu2+ complexes. A preparative, potentiometric titration and NMR spectroscopic study.

PubMed

Plush, Sally E; Lincoln, Stephen F; Wainwright, Kevin P

2004-05-07

The pK(a)s and Zn2+, Cd2+ and Cu2+ complexation constants (K) for 1,4,7-tris[(2''S)-acetamido-2''-(methyl-3''-phenylpropionate)]-1,4,7-triazacyclononane, 1, 1,4,7-tris[(2''S)-acetamido-2''-(1''-carboxy-3''-phenylpropane)]-1,4,7-triazacyclononane, H(3)2, 1,4,7-tris[(2''S)-acetamido-2''-(methyl-3''-(1H-3-indolyl)propionate)]-1,4,7-triazacyclononane, 3, and 1,4,7,10-tetrakis[(2''S)-acetamido-2''-(methyl-3''-phenylpropionate)]-1,4,7,10-tetraazacyclododecane, 4, 1,4,7,10-tetrakis[(2''S)-acetamido-2''-(1''-carboxy-3''-phenylpropane)]-1,4,7,10-tetraazacyclododecane, H(4)5, in 20 : 80 v/v water-methanol solution are reported. The pK(a)s within the potentiometric detection range for H(3)1(3+) = 8.69 and 3.59, for H(6)2(3+) = 9.06, 6.13, 4.93 and 4.52, H(3)3(3+) = 8.79 and 3.67, H(4)4(4+) = 8.50, 5.62 and 3.77 and for H(8)5(4+) = 9.89, 7.06, 5.53, 5.46, 4.44 and 4.26 where each tertiary amine nitrogen is protonated. The complexes of 1: [Zn(1)]2+(9.00), [Cd(1)]2+ (6.49), [Cd(H1)]3+ (4.54) and [Cu(1)]2+ (10.01) are characterized by the log(K/dm3 mol(-1)) values shown in parentheses. Analogous complexes are formed by 3 and 4: [Zn(3)]2+ (10.19), [Cd(3)]2+ (8.54), [Cu(3)]2+ (10.77), [Zn(4)]2+ (11.41) [Cd(4)]2+ (9.16), [Cd(H4)]3+ (6.16) and [Cu(4)]2+ (11.71). The tricarboxylic acid H(3)2 generates a greater variety of complexes as exemplified by: [Zn(2)-] (10.68) [Zn(H2)] (6.60) [Zn(H(2)2)+] (5.15), [Cd(2)](-) (4.99), [Cd(H2)] (4.64), [Cd(H2(2))]+ (3.99), [Cd(H(3)2)]2+ (3.55), [Cu(2)](-) (12.55) [Cu(H2)] (7.66), [Cu(H(2)2)]+ (5.54) and [Cu(2)2](4-) (3.23). The complexes of H(4)5 were insufficiently soluble to study in this way. The 1H and 13C NMR spectra of the ligands are consistent with formation of a predominant Zn2+ and Cd2+ Delta or Lambda diastereomer. The preparations of the new pendant arm macrocycles H(3)2, 3, 4 and H(4)5 are reported.

Microwave assisted synthesis of bis and tris(ω-bromoacetophenones): versatile precursors for novel bis(imidazo[1,2-a]pyridines), bis(imidazo[1,2-a]pyrimidines) and their tris-analogs

PubMed Central

2013-01-01

Background α-Bromination of the side chain of aromatic ketones using NBS in the presence of p-toluenesulfonic acid (p-TsOH) in acetonitrile is very common. However, regioselective bromination of bis and tris(ω-bromoacetophenones) with NBS in the presence of p-TsOH in acetonitrile under microwave irradiation is quite novel. The bis- and tris(ω-bromoacetophenones) are used in synthesis of bis and tris(heterocycles). bis(heterocycles) have received a great deal of attention, because many biologically active natural and synthetic products have molecular symmetry. The use of the pressurized microwave irradiation is very advantageous to many syntheses and provide a large rate enhancement. Results Bis and tris(ω-bromoacetophenones) were obtained as single monobrominated derivatives in a shorter time than the conventional conditions. The results clearly demonstrate the better reactivity and selectivity of NBS/p-TsOH/CH3CN as a brominating mixture under microwave conditions. The reaction of bis and tris(ω-bromoacetophenone) with 2-aminopyridine and 2-aminopyrimidine proceeded smoothly in a mixture of anhydrous ethanol and DMF under reflux or using 300 W/105°C/ 20 min microwave irradiation conditions to afford the corresponding bis(imidazo[1,2-a]pyridine), bis(imidazo[1,2-a]pyrimidine) and tris(imidazo[1,2-a]pyridine) derivatives in moderate to excellent yields. The carbonyl analogue of the targeted bis(imidazopyridines) could be synthesized by the reaction of N,N-dimethyl-N'-(pyridin-2-yl)formimidamide with bis(ω-bromoacetophenone) in refluxing ethanol. The structures of the newly synthesized compounds were confirmed by their spectral data as well as their elemental analyses. Conclusion In conclusion, selective α-bromination of bis- and tris(acetophenones) has been accomplished efficiently utilizing NBS/p-TsOH/CH3CN under microwave irradiation. In addition, a facile synthesis of novel series of bis- and tris(imidazopyridine) and bis(imidazopyrimidine) derivatives. PMID:23782550

Nanomolar colorimetric quantitative detection of Fe3 + and PPi with high selectivity

NASA Astrophysics Data System (ADS)

Li, Zhanxian; Li, Haixia; Shi, Caixia; Yu, Mingming; Wei, Liuhe; Ni, Zhonghai

2016-04-01

A novel rhodamine and 8-hydroxyquinoline-based derivative was synthesized, which is shown to act as a colorimetric chemosensor for Fe3 + in aqueous solution with high selectivity over various environmentally and biologically relevant metal ions and anions with a distinct color change from colorless to pink in very fast response time (< 1 min). Fe3 + can be detected quantitatively in the concentration range from 6.7 to 16 μM and the detection limit (LOD) on UV-vis response of the sensor can be as low as 15 nM. The 'in situ' prepared Fe3 + complex (1 ṡ Fe) showed high selectivity toward PPi against many common anions, and sensitivity (the LOD can be as low as 71 nM). In addition, both the chemosensor and the 'in situ' prepared Fe3 + complex are reusable for the detection of Fe3 + and PPi respectively.

Three novel coordination polymers based on tris(p-carboxyphenyl)phosphane oxide: Syntheses, structural characterization and magnetic properties

NASA Astrophysics Data System (ADS)

Huo, Liangqin; Fan, Liming; Zhang, Jie; Gao, Lingling; Zhai, Lijun; Wang, Xiaoqing; Hu, Tuoping

2018-05-01

Three coordination polymers (CPs), namely, {[Co3(HL)2(bib)3 (H2O)7]·12H2O}n (1), {[Co(HL)(bib)]·H2O}n (2), and {[Co1.5(L)(bibp)1.5 (H2O)]·1.5DMF·2EtOH·3H2O}n (3), have been synthesized from the tripodal ligand of tris(p-carboxyphenyl)phosphane oxide (H3L) with the help of 1,4-bis(imidazol-1-yl)benzene (bib) or 4,4‧-bis(imidazol-1-yl)biphenyl (bibp). Structural analyses reveal that complex 1 features a 3D 4-connected {650.8}-cds net. 2 displays a 2D 6-connected {360.460.53}-hxl sheet based on the binuclear {Co2(COO)2} SBUs. Complex 3 shows a 3D (3,4,4)-connected net with {6·82}2{6·840.10}2{620.820.102} point symbol. Furthermore, the results of the variable-temperature magnetic susceptibilities indicate that complexes 1-3 have antiferromagnetic behavior between Co(II) ions.

The Antemortem Detection and Conformational Switches of Prion Proteins

DTIC Science & Technology

2006-07-01

distribution of di-, mono-, and unglycosylated PrPC molecules (Fig. 7B, lane 2). Subsequent elution of the column with N-acetyl glucosamine yielded...pellet was washed in 50 mM Tris, pH 8.0, 150 mM NaCl, and then solubilized in 6 M guanidinium hydrochloride , 50 mM Tris pH 8.0, 150 mM NaCl. The...and 150mM sodium chloride (TCl) containing 6M guanidinium hydrochloride . The supernatant was centrifuged for 30min at 18,000g. The protein was

Permeation Studies of CW Agents with Fabric Treated with 8-Hydroxyquinoline

DTIC Science & Technology

2017-12-01

Jeffery R. Owens AIR FORCE CIVIL ENGINEER CENTER AFCEC/CXAE, Tyndall AFB, FL 32403-5320 December 2017 Approved for public release: distribution...P.O. Box 68, Gunpowder, MD 21010-0068 Universal Technology Corp.; 139 Barnes Drive Suite 2 Tyndall AFB, FL 32404-5325 Air Force Civil Engineer ...moisture transport. The garment prevents exposure to outside chemical weapons agents (CWAs) by reacting or reducing permeation of the CWA. By

Molecular Imaging of Tumors Using a Quantitative T1 Mapping Technique via Magnetic Resonance Imaging

PubMed Central

Herrmann, Kelsey; Johansen, Mette L.; Craig, Sonya E.; Vincent, Jason; Howell, Michael; Gao, Ying; Lu, Lan; Erokwu, Bernadette; Agnes, Richard S.; Lu, Zheng-Rong; Pokorski, Jonathan K.; Basilion, James; Gulani, Vikas; Griswold, Mark; Flask, Chris; Brady-Kalnay, Susann M.

2015-01-01

Magnetic resonance imaging (MRI) of glioblastoma multiforme (GBM) with molecular imaging agents would allow for the specific localization of brain tumors. Prior studies using T1-weighted MR imaging demonstrated that the SBK2-Tris-(Gd-DOTA)3 molecular imaging agent labeled heterotopic xenograft models of brain tumors more intensely than non-specific contrast agents using conventional T1-weighted imaging techniques. In this study, we used a dynamic quantitative T1 mapping strategy to more objectively compare intra-tumoral retention of the SBK2-Tris-(Gd-DOTA)3 agent over time in comparison to non-targeted control agents. Our results demonstrate that the targeted SBK2-Tris-(Gd-DOTA)3 agent, a scrambled-Tris-(Gd-DOTA)3 control agent, and the non-specific clinical contrast agent Optimark™ all enhanced flank tumors of human glioma cells with similar maximal changes on T1 mapping. However, the retention of the agents differs. The non-specific agents show significant recovery within 20 min by an increase in T1 while the specific agent SBK2-Tris-(Gd-DOTA)3 is retained in the tumors and shows little recovery over 60 min. The retention effect is demonstrated by percent change in T1 values and slope calculations as well as by calculations of gadolinium concentration in tumor compared to muscle. Quantitative T1 mapping demonstrates the superior binding and retention in tumors of the SBK2-Tris-(Gd-DOTA)3 agent over time compared to the non-specific contrast agent currently in clinical use. PMID:26435847

Cloud point extraction of vanadium in pharmaceutical formulations, dialysate and parenteral solutions using 8-hydroxyquinoline and nonionic surfactant.

PubMed

Khan, Sumaira; Kazi, Tasneem G; Baig, Jameel A; Kolachi, Nida F; Afridi, Hassan I; Wadhwa, Sham Kumar; Shah, Abdul Q; Kandhro, Ghulam A; Shah, Faheem

2010-10-15

A cloud point extraction (CPE) method has been developed for the determination of trace quantity of vanadium ions in pharmaceutical formulations (PF), dialysate (DS) and parenteral solutions (PS). The CPE of vanadium (V) using 8-hydroxyquinoline (oxine) as complexing reagent and mediated by nonionic surfactant (Triton X-114) was investigated. The parameters that affect the extraction efficiency of CPE, such as pH of sample solution, concentration of oxine and Triton X-114, equilibration temperature and time period for shaking were investigated in detail. The validity of CPE of V was checked by standard addition method in real samples. The extracted surfactant-rich phase was diluted with nitric acid in ethanol, prior to subjecting electrothermal atomic absorption spectrometry. Under these conditions, the preconcentration of 50 mL sample solutions, allowed raising an enrichment factor of 125-fold. The lower limit of detection obtained under the optimal conditions was 42 ng/L. The proposed method has been successfully applied to the determination of trace quantity of V in various pharmaceutical preparations with satisfactory results. The concentration ranges of V in PF, DS and PS samples were found in the range of 10.5-15.2, 0.65-1.32 and 1.76-6.93 microg/L, respectively. 2010 Elsevier B.V. All rights reserved.

8-Hydroxyquinoline and hydroxamic acid inhibitors of botulinum neurotoxin BoNT/A.

PubMed

Dickerson, Tobin J; Smith, Garry R; Pelletier, Jeffrey C; Reitz, Allen B

2014-01-01

We describe here the state of the art of certain aspects concerning potential small molecule therapy directed toward botulism, by inhibition of the zinc-protease containing light chain (LC) of botulinum neurotoxin BoNT/A from the anaerobic bacillus Clostridium botulinum. Botulinum neurotoxins (BoNTs) are comprised of eight serologically-distinct proteins (A - H), several of which are further divided, such as BoNT/A which has five subtypes. The BoNTs are the most toxic substances known to mankind, causing a form of flaccid paralysis that can be rapid and is often lethal. BoNT/A is comprised of a ~100 kDa heavy chain (HC) attached via a single disulfide Cys-Cys bond to a ~50 kDa LC. The HC mediates transport to and uptake by presynaptic glutamatergic neurons, where the LC cleaves the protein SNAP-25 and thus prevents vesicular trafficking and release of acetylcholine. The Zn-endoprotease activity of the LC of BoNT/A is a target for the development of small molecule inhibitors of BoNT/A-mediated toxicity. A variety of BoNT/A LC inhibitors have been described to date and we focus here primarily on the Zn-binding 8-hydroxyquinoline structural type as well as some of the previously-described hydroxamic acids.

Tracing organophosphorus and brominated flame retardants and plasticizers in an estuarine food web.

PubMed

Brandsma, Sicco H; Leonards, Pim E G; Leslie, Heather A; de Boer, Jacob

2015-02-01

Nine organophosphorus flame retardants (PFRs) were detected in a pelagic and benthic food web of the Western Scheldt estuary, The Netherlands. Concentrations of several PFRs were an order of magnitude higher than those of the brominated flame retardants (BFRs). However, the detection frequency of the PFRs (6-56%) was lower than that of the BFRs (50-97%). Tris(2-butoxyethyl) phosphate (TBOEP), tris(isobutyl) phosphate (TIBP) and tris(2-chloroisopropyl) phosphate (TCIPP) were the dominant PFRs in sediment with median concentrations of 7.0, 8.1 and 1.8 ng/g dry weight (dw), respectively. PFR levels in the suspended particular matter (SPM) were 2-12 times higher than that in sediment. TBOEP, TCIPP, TIBP, tris(2-chloroethyl) phosphate (TCEP) and tris(phenyl) phosphate (TPHP) were found in organisms higher in the estuarine food web. The highest PFR concentrations in the benthic food web were found in sculpin, goby and lugworm with median concentrations of 17, 7.4, 4.6 and 2.0 ng/g wet weight (ww) for TBOEP, TIBP, TCIPP and TPHP, respectively. Comparable levels were observed in the pelagic food web, BDE209 was the predominant PBDE in sediment and SPM with median concentrations up to 9.7 and 385 ng/g dw, respectively. BDE47 was predominant in the biotic compartment of the food web with highest median levels observed in sculpin and common tern eggs of 79 ng/g lipid weight (lw) (2.5 ng/g ww) and 80 ng/g lw (11 ng/g ww), respectively. Trophic magnification was observed for all PBDEs with the exception of BDE209. Indications of trophic magnification of PFRs were observed in the benthic food web for TBOEP, TCIPP and TCEP with tentative trophic magnification factors of 3.5, 2.2 and 2.6, respectively (p<0.05). Most of the other PFRs showed trophic dilution in both food webs. The relative high PFR levels in several fish species suggest high emissions and substantial exposure of organisms to PFRs in the Western Scheldt. Copyright © 2014 Elsevier B.V. All rights reserved.

Preliminary evaluation of monolithic column high-performance liquid chromatography with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection for the determination of quetiapine in human body fluids.

PubMed

Bellomarino, Sara A; Brown, Allyson J; Conlan, Xavier A; Barnett, Neil W

2009-03-15

High-performance liquid chromatography (HPLC) with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection methodology is reported for the determination of the atypical antipsychotic drug quetiapine and the observation of its major active and inactive metabolites in human urine and serum. The method uses a monolithic chromatographic column allowing high flow rates of 3 mLmin(-1) enabling rapid quantification. Flow injection analysis (FIA) with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection and HPLC time of flight mass spectrometry (TOF-MS) were used for the determination of quetiapine in a pharmaceutical preparation to establish its suitability as a calibration standard. The limit of detection achieved with FIA was 2 x 10(-11) molL(-1) in simple aqueous solution. The limits of detection achieved with HPLC were 7 x 10(-8) and 2 x 10(-10) molL(-1) in urine and serum, respectively. The calibration range for FIA was between 5 x 10(-9) and 1 x 10(-6) molL(-1). The calibration ranges for HPLC were between 1 x 10(-7)-1 x 10(-4) and 1 x 10(-8)-1 x 10(-4) molL(-1) in urine and serum, respectively. The quetiapine concentrations in patient samples were found to be 3 x 10(-6) molL(-1) in urine and 7 x 10(-7) molL(-1) in serum. Without the need for preconcentration, the HPLC detection limits compared favourably with those in previously published methodologies. The metabolites were identified using HPLC-TOF-MS.

Three-component entanglements consisting of three crescent-shaped bidentate ligands coordinated to an octahedral metal centre.

PubMed

Durola, Fabien; Russo, Luca; Sauvage, Jean-Pierre; Rissanen, Kari; Wenger, Oliver S

2007-01-01

3,3'-biisoquinoline ligands (biiq) L, bearing aromatic substituents on their 8 and 8' positions, have been used to generate interwoven systems consisting of three crescent-shaped ligands disposed around an octahedral metal centre. Mono-ligand complexes of the type [ReL(CO)3py]+ (py: pyridine) have also been prepared, leading to sterically non-hindering complexes in spite of the endotopic nature of the chelate used. The three-component entanglements have been prepared by using either FeII or RuII as gathering metal centre. The synthetic procedure is simple and efficient, affording fully characterised complexes as their PF6 or SbCl6 salts. X-ray crystallography clearly shows that the crescent-shaped ligands do not repel each other in the tris-chelate complexes. In an analogous way, the ReI complexes show open structures with no steric repulsion between the L ligand and the ancillary CO or py groups. The FeL3 or RuL3 compounds are very unusual in the sense that, contrary to all the other tris-bidentate chelate complexes made till now, the three organic components are tangled up, in a situation which will be very favourable to the formation of new non trivial topologies of the catenane type.

Pressure-Sensitive Paint: Effect of Substrate

PubMed Central

Quinn, Mark Kenneth; Yang, Leichao; Kontis, Konstantinos

2011-01-01

There are numerous ways in which pressure-sensitive paint can be applied to a surface. The choice of substrate and application method can greatly affect the results obtained. The current study examines the different methods of applying pressure-sensitive paint to a surface. One polymer-based and two porous substrates (anodized aluminum and thin-layer chromatography plates) are investigated and compared for luminescent output, pressure sensitivity, temperature sensitivity and photodegradation. Two luminophores [tris-Bathophenanthroline Ruthenium(II) Perchlorate and Platinum-tetrakis (pentafluorophenyl) Porphyrin] will also be compared in all three of the substrates. The results show the applicability of the different substrates and luminophores to different testing environments. PMID:22247685

TRIS buffer in simulated body fluid distorts the assessment of glass-ceramic scaffold bioactivity.

PubMed

Rohanová, Dana; Boccaccini, Aldo Roberto; Yunos, Darmawati Mohamad; Horkavcová, Diana; Březovská, Iva; Helebrant, Aleš

2011-06-01

The paper deals with the characterisation of the bioactive phenomena of glass-ceramic scaffold derived from Bioglass® (containing 77 wt.% of crystalline phases Na(2)O·2CaO·3SiO(2) and CaO·SiO(2) and 23 wt.% of residual glass phase) using simulated body fluid (SBF) buffered with tris-(hydroxymethyl) aminomethane (TRIS). A significant effect of the TRIS buffer on glass-ceramic scaffold dissolution in SBF was detected. To better understand the influence of the buffer, the glass-ceramic scaffold was exposed to a series of in vitro tests using different media as follows: (i) a fresh liquid flow of SBF containing tris (hydroxymethyl) aminomethane; (ii) SBF solution without TRIS buffer; (iii) TRIS buffer alone; and (iv) demineralised water. The in vitro tests were provided under static and dynamic arrangements. SBF buffered with TRIS dissolved both the crystalline and residual glass phases of the scaffold and a crystalline form of hydroxyapatite (HAp) developed on the scaffold surface. In contrast, when TRIS buffer was not present in the solutions only the residual glassy phase dissolved and an amorphous calcium phosphate (Ca-P) phase formed on the scaffold surface. It was confirmed that the TRIS buffer primarily dissolved the crystalline phase of the glass-ceramic, doubled the dissolving rate of the scaffold and moreover supported the formation of crystalline HAp. This significant effect of the buffer TRIS on bioactive glass-ceramic scaffold degradation in SBF has not been demonstrated previously and should be considered when analysing the results of SBF immersion bioactivity tests of such systems. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Can activated sludge treatments and advanced oxidation processes remove organophosphorus flame retardants?

PubMed

Cristale, Joyce; Ramos, Dayana D; Dantas, Renato F; Machulek Junior, Amilcar; Lacorte, Silvia; Sans, Carme; Esplugas, Santiago

2016-01-01

This study aims to determine the occurrence of 10 OPFRs (including chlorinated, nonchlorinated alkyl and aryl compounds) in influent, effluent wastewaters and partitioning into sludge of 5 wastewater treatment plants (WWTP) in Catalonia (Spain). All target OPFRs were detected in the WWTPs influents, and the total concentration ranged from 3.67 µg L(-1) to 150 µg L(-1). During activated sludge treatment, most OPFRs were accumulated in the sludge at concentrations from 35.3 to 9980 ng g(-1) dw. Chlorinated compounds tris(2-chloroethyl) phosphate (TCEP), tris(2-chloroisopropyl) phosphate (TCIPP) and tris(2,3-dichloropropyl) phosphate (TDCPP) were not removed by the conventional activated sludge treatment and they were released by the effluents at approximately the same inlet concentration. On the contrary, aryl compounds tris(methylphenyl) phosphate (TMPP) and 2-ethylhexyl diphenyl phosphate (EHDP) together with alkyl tris(2-ethylhexyl) phosphate (TEHP) were not detected in any of the effluents. Advanced oxidation processes (UV/H2O2 and O3) were applied to investigate the degradability of recalcitrant OPFRs in WWTP effluents. Those detected in the effluent sample (TCEP, TCIPP, TDCPP, tributyl phosphate (TNBP), tri-iso-butyl phosphate (TIBP) and tris(2-butoxyethyl) phosphate (TBOEP)) had very low direct UV-C photolysis rates. TBOEP, TNBP and TIBP were degraded by UV/H2O2 and O3. Chlorinated compounds TCEP, TDCPP and TCIPP were the most recalcitrant OPFR to the advanced oxidation processes applied. The study provides information on the partitioning and degradability pathways of OPFR within conventional activated sludge WWTPs. Copyright © 2015 Elsevier Inc. All rights reserved.

Gallium(iii) and iron(iii) complexes of quinolone antimicrobials.

PubMed

Mjos, Katja Dralle; Cawthray, Jacqueline F; Polishchuk, Elena; Abrams, Michael J; Orvig, Chris

2016-08-16

Iron is an essential nutrient for many microbes. According to the "Trojan Horse Hypothesis", biological systems have difficulties distinguishing between Fe(3+) and Ga(3+), which constitutes the antimicrobial efficacy of the gallium(iii) ion. Nine novel tris(quinolono)gallium(iii) complexes and their corresponding iron(iii) analogs have been synthesized and fully characterized. Quinolone antimicrobial agents from three drug generations were used in this study: ciprofloxacin, enoxacin, fleroxacin, levofloxacin, lomefloxacin, nalidixic acid, norfloxacin, oxolinic acid, and pipemidic acid. The antimicrobial efficacy of the tris(quinolono)gallium(iii) complexes was studied against E. faecalis and S. aureus (both Gram-positive), as well as E. coli, K. pneumonia, and P. aeruginosa (all Gram-negative) in direct comparison to the tris(quinolono)iron(iii) complexes and the corresponding free quinolone ligands at various concentrations. For the tris(quinolono)gallium(iii) complexes, no combinational antimicrobial effects between Ga(3+) and the quinolone antimicrobial agents were observed.

Organophosphate flame retardants in the indoor air and dust in cars in Japan.

PubMed

Tokumura, Masahiro; Hatayama, Rurika; Tatsu, Kouichi; Naito, Toshiyuki; Takeda, Tetsuya; Raknuzzaman, Mohammad; -Al-Mamun, Md Habibullah; Masunaga, Shigeki

2017-01-01

The concentrations of organophosphate flame retardants (OPFRs) in the indoor air and dust were measured in 25 unoccupied cars in Japan. In the indoor air of the cars, most OPFRs were neither detected nor found at a concentration lower than the method quantification limit. The highest concentration (1500 ng m -3 ) was obtained for tris(1-chloro-2-propyl) phosphate (TCIPP). By contrast, many OPFRs were detected in the dust samples collected from the interior of the cars. TCIPP and tris(2-ethylhexyl) phosphate (TEHP) were present at the highest concentrations at 390 μg g -1 (in dust from car seats) and 640 μg g -1 (in dust from car floor mats), respectively. The highest median concentrations (35 μg g -1 for car seats, 53 μg g -1 for car floor mats) were obtained for tris(2-butoxyethyl) phosphate (TBOEP). According to the results of our exposure assessment, the typical exposures to OPFRs via inhalation in car cabins ranged from 9.0×10 -4 to 7.8×10 -1 ng kg-bw -1 day -1 . The typical exposures to OPFRs via dust ingestion ranged from 9.2×10 -4 to 8.8×10 -1 ng kg-bw -1 day -1 . We compared these results with the ref-erence doses for OPFRs and found that, based on cur-rent information about the toxicities of OPFRs, exposure to OPFRs in car cabins via inhalation and dust ingestion is unlikely to have adverse human health effects.

Electrogenerated chemiluminescence of tris(2,2' bipyridine)ruthenium(II) using common biological buffers as co-reactant, pH buffer and supporting electrolyte.

PubMed

Kebede, Noah; Francis, Paul S; Barbante, Gregory J; Hogan, Conor F

2015-11-07

A series of aliphatic tertiary amines (HEPES, POPSO, EPPS and BIS-TRIS) commonly used to buffer the pH in biological experiments, were examined as alternative, non-toxic co-reactants for the electrogenerated chemiluminescence (ECL) of tris(2,2'-bipyridine)ruthenium(ii) ([Ru(bpy)3](2+)). These were found to be very attractive as "multi-tasking" reagents, serving not only as co-reactants, but also fulfiling the roles of pH buffer and supporting electrolyte within an aqueous environment; thus significantly simplifying the overall ECL analysis. Sub-nanomolar detection limits were obtained for [Ru(bpy)3](2+) in the presence of BIS-TRIS, making this species an valuable option for co-reactant ECL-based bioanalytical applications.

SEPARATION PROCESS USING COMPLEXING AND ADSORPTION

DOEpatents

Spedding, J.H.; Ayers, J.A.

1958-06-01

An adsorption process is described for separating plutonium from a solution of neutron-irradiated uranium containing ions of a compound of plutonium and other cations. The method consists of forming a chelate complex compound with plutoniunn ions in the solution by adding a derivative of 8- hydroxyquinoline, which derivative contains a sulfonic acid group, and adsorbing the remaining cations from the solution on a cation exchange resin, while the complexed plutonium remains in the solution.

Pseudotetrahedral manganese complexes supported by the anionic tris(phosphino)borate ligand [PhBPiPr3

PubMed Central

Lu, Connie C.; Peters, Jonas C.

2008-01-01

This paper presents aspects of the coordination chemistry of mono- and divalent manganese complexes supported by the anionic tris(phosphino)borate ligand, [PhBPiPr3] (where [PhBPiPr3] = [PhB(CH2PiPr2)3]−). The Mn(II) halide complexes, [PhBPiPr3]MnCl (1 and [PhBPiPr3]MnI (2), have been characterized by X-ray diffraction, SQUID magnetometry, and EPR spectroscopy. Compound 2 serves as a precursor to a series of Mn azide, alkyl, and amide species: [PhBPiPr3]Mn(N3) (3), [PhBPiPr3]Mn(CH2Ph) (4), [PhBPiPr3]Mn(Me) (5), [PhBPiPr3]Mn(NH(2,6-iPr2-C6H3)) (6), [PhBPiPr3]Mn(dbabh) (7), and [PhBPiPr3]Mn(1-Ph(isoindolate)) (8). The complexes 2 – 8 feature a divalent-metal center and are pseudotetrahedral. They collectively represent an uncommon structural motif for low-coordinate, polyphosphine-supported Mn complexes. Two Mn(I) species have also been prepared. These include the Tl-Mn adduct, [PhBPiPr3]Tl-MnBr(CO)4 (9), and the octahedral complex [PhBPiPr3]Mn(CNtBu)3 (10). Some of our initial synthetic efforts to generate [PhBPiPr3]Mn≡Nx species are briefly described, as are DFT studies that probe the electronic viability of these types of multiply bonded target structures. PMID:17029370

Interactions of TRIS [tris(hydroxymethyl)aminomethane] and related buffers with peptide backbone: thermodynamic characterization.

PubMed

Taha, Mohamed; Lee, Ming-Jer

2010-10-21

In a situation which is far from ideal, many buffers have been found to be quite reactive, besides maintaining their stable pH values. On the basis of apparent transfer free energies (ΔG(tr)'), through solubility measurements the interactions of zwitterionic glycine peptides: glycine (Gly), diglycine (Gly(2)), triglycine (Gly(3)), and tetraglycine (Gly(4)), with several common neutral pH, amine-based buffers have been studied. The biological buffers studied in this work, including TRIS, TES, TAPS, TAPSO, and TABS are structurally related and all contain TRIS groups. These buffers have pK(a) values ranging from 7.5-9.0, which allow them to be used in biological, biochemical or environmental studies. We observed negative values of ΔG(tr)' for Gly(3) and Gly(4) from water to buffer, indicating that the interactions are favorable. However, the ΔG(tr)' values are positive for Gly and Gly(2), revealing unfavorable interactions, which except for the latter in TRIS buffer are negative. The surprising result in our data is the unexpected extraordinarily high favorable interactions between TRIS buffer and peptides (in comparison with the effect of the most common denaturants, urea and guanidine hydrochloride). The transfer free energies (ΔG(tr)') of the peptide backbone unit (-CH(2)C=O-NH-) contributions have been estimated from ΔG(tr)' values. We have also investigated the interactions of TRIS buffer with Bovine Serum Albumin (BSA), as a globular protein, using dynamic light scattering (DLS), zeta potential, UV-Visible absorption, fluorescence and Raman spectroscopy measurements. The results indicated that TRIS buffer stabilized the BSA molecules.

Chemoembolization of Neuroendocrine Liver Metastases Using Streptozocin and Tris-acryl Microspheres: Embozar (EMBOsphere + ZAnosaR) Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pelage, Jean-Pierre, E-mail: pelage-jp@chu-caen.fr; Fohlen, Audrey; Mitry, Emmanuel

PurposeThe purpose of this prospective observational study was to evaluate the efficacy and tolerability of transarterial chemoembolization (TACE) for neuroendocrine liver metastases using a combination of streptozocin, Lipiodol, and tris-acryl microspheres.Patients and MethodsA total of 16 men and 9 women aged 59.6 ± 11.3 years, all with predominant liver disease, underwent 54 courses of TACE using an emulsion of 1.5 g of streptozocin and 10 ml of Lipiodol. Additional embolization was performed using 300–500 µm tris-acryl microspheres. Morphological response was evaluated using the RECIST criteria on multi-detector computed tomography or MRI. Clinical efficacy was evaluated particularly in patients with carcinoid syndrome.ResultsThe primary tumor was located inmore » the small bowel or pancreas in 21 (84%) patients. Eleven (44%) patients presented with a carcinoid syndrome. Nineteen (76%) patients presented with more than 10 liver nodules. One delayed case of ischemic cholecystitis was treated conservatively. After a median follow-up of 36.1 months, 1 (4%) patient had a complete response, 12 (48%) patients had a partial response, and 7 (28%) patients had a stable disease corresponding to a disease control rate of 80%. All patients with carcinoid syndrome had significant improvement. Median time to progression was 18.8 months and overall survival was 100, 100, and 92% at 1, 2, and 3 years, respectively. Seven patients presented with extrahepatic progression with abdominal lymphadenopathies or metastases to the brain, ovary, adrenal gland, or lung.ConclusionOptimized TACE using a combination of streptozocin, Lipiodol, and tris-acryl microspheres is effective and well tolerated.« less

Balance the Carrier Mobility To Achieve High Performance Exciplex OLED Using a Triazine-Based Acceptor.

PubMed

Hung, Wen-Yi; Chiang, Pin-Yi; Lin, Shih-Wei; Tang, Wei-Chieh; Chen, Yi-Ting; Liu, Shih-Hung; Chou, Pi-Tai; Hung, Yi-Tzu; Wong, Ken-Tsung

2016-02-01

A star-shaped 1,3,5-triazine/cyano hybrid molecule CN-T2T was designed and synthesized as a new electron acceptor for efficient exciplex-based OLED emitter by mixing with a suitable electron donor (Tris-PCz). The CN-T2T/Tris-PCz exciplex emission shows a high ΦPL of 0.53 and a small ΔET-S = -0.59 kcal/mol, affording intrinsically efficient fluorescence and highly efficient exciton up-conversion. The large energy level offsets between Tris-PCz and CN-T2T and the balanced hole and electron mobility of Tris-PCz and CN-T2T, respectively, ensuring sufficient carrier density accumulated in the interface for efficient generation of exciplex excitons. Employing a facile device structure composed as ITO/4% ReO3:Tris-PCz (60 nm)/Tris-PCz (15 nm)/Tris-PCz:CN-T2T(1:1) (25 nm)/CN-T2T (50 nm)/Liq (0.5 nm)/Al (100 nm), in which the electron-hole capture is efficient without additional carrier injection barrier from donor (or acceptor) molecule and carriers mobilities are balanced in the emitting layer, leads to a highly efficient green exciplex OLED with external quantum efficiency (EQE) of 11.9%. The obtained EQE is 18% higher than that of a comparison device using an exciplex exhibiting a comparable ΦPL (0.50), in which TCTA shows similar energy levels but higher hole mobility as compared with Tris-PCz. Our results clearly indicate the significance of mobility balance in governing the efficiency of exciplex-based OLED. Exploiting the Tris-PCz:CN-T2T exciplex as the host, we further demonstrated highly efficient yellow and red fluorescent OLEDs by doping 1 wt % Rubrene and DCJTB as emitter, achieving high EQE of 6.9 and 9.7%, respectively.

Exciplex emission and decay of co-deposited 4,4',4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl)mesityl]borane organic light-emitting devices with different electron transporting layer thicknesses

NASA Astrophysics Data System (ADS)

Huang, Qingyu; Zhao, Suling; Xu, Zheng; Fan, Xing; Shen, Chongyu; Yang, Qianqian

2014-04-01

Highly efficient fluorescence organic light-emitting diodes (OLEDs) based on the mixed 4,4',4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl)mesityl]borane (1:1) system are reported. The electroluminescence due to the exciplex emission is red shifted when the thickness of the electron-transporting layer increases. The prepared OLEDs achieve a low turn-on voltage of 2.1 V, a high current efficiency of 36.79 cd/A, and a very high luminescence of 17 100 cd/m2, as well as a low efficiency roll-off. The current efficiency of the optimized OLED is maintained at more than 28.33 cd/A up to 10 000 cd m-2. The detailed recombination mechanism of the prepared OLEDs is investigated by the transient electroluminescence method. It is concluded that there are no contributions from trapped charges and annihilations of triplet-triplet excitons to the detected electroluminescence.

Photo-degradation behaviour of roseoflavin in some aqueous solutions

NASA Astrophysics Data System (ADS)

Tyagi, A.; Penzkofer, A.; Mathes, T.; Hegemann, P.

2010-03-01

An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

Isolation of aluminum-tolerant bacteria capable of nitrogen removal in activated sludge.

PubMed

Ji, Bin; Chen, Wei; Zhu, Lei; Yang, Kai

2016-05-15

Four strains of bacteria capable of withstanding 20mM concentration of aluminum were isolated from activated sludge in a bioreactor. 16S rRNA identification and morphological characteristics indicated that these strains were Chryseobacterium sp. B1, Brevundimonas diminuta B3, Hydrogenophaga sp. B4, and Bacillus cereus B5. Phylogenetic analysis revealed the position and interrelationships of these bacteria. B. diminuta B3 and Hydrogenophaga sp. B4 could achieve nitrate nitrogen removal of 94.0% and 76.8% within 36h of its initial concentration of 148.8 and 151.7mg/L, respectively. Meanwhile, B3 and B4 could degrade ammonia with little nitrite accumulation. Results of this study provide more information about aluminum-resistant bacteria and laid the foundation for aluminum salt when it is simultaneously used for chemical precipitation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Self-assembly of an imidazolate-bridged Fe(III)/Cu(II) heterometallic cage.

PubMed

Reichel, Florian; Clegg, Jack K; Gloe, Karsten; Gloe, Kerstin; Weigand, Jan J; Reynolds, Jason K; Li, Chun-Guang; Aldrich-Wright, Janice R; Kepert, Cameron J; Lindoy, Leonard F; Yao, Hong-Chang; Li, Feng

2014-01-21

A rare, discrete, mixed-valent, heterometallic Fe(III)/Cu(II) cage, [Cu6Fe8L8](ClO4)12·χsolvent (H3L = tris{[2-{(imidazole-4-yl)methylidene}amino]ethyl}amine), was designed and synthesized via metal-ion-directed self-assembly with neutral tripodal metalloligands. The formation of this coordination cage was demonstrated by X-ray crystallography, ESI mass spectrometry, FT-IR, and UV-vis-NIR spectroscopy.

Long coherence times in nuclear spin-free vanadyl qubits [Long coherence times in surface-compatible nuclear spin-free vanadium qubits

DOE PAGES

Yu, Chung -Jui; Graham, Michael J.; Zadrozny, Joseph M.; ...

2016-10-31

Quantum information processing (QIP) offers the potential to create new frontiers in fields ranging from quantum biology to cryptography. Two key figures of merit for electronic spin qubits, the smallest units of QIP, are the coherence time ( T2), the lifetime of the qubit, and the spin–lattice relaxation time ( T1), the thermally defined upper limit of T2. To achieve QIP, processable qubits with long coherence times are required. Recent studies on (Ph4P-d20)2[V(C8S8)3], a vanadium-based qubit, demonstrate that millisecond T2 times are achievable in transition metal complexes with nuclear spinfree environments. Applying these principles to vanadyl complexes offers a routemore » to combine the previously established surface compatibility of the flatter vanadyl structures with a long T2. Toward those ends, we investigated a series of four qubits, (Ph 4P) 2[VO(C 8S 8) 2] (1), (Ph 4P) 2[VO(β-C 3S 5) 2] (2), (Ph 4P) 2[VO(α-C 3S 5) 2] (3), and (Ph 4P) 2[VO(C 3S 4O) 2] (4), by pulsed electron paramagnetic resonance (EPR) spectroscopy and compared the performance of these species with our recently reported set of vanadium tris(dithiolene) complexes. Crucially we demonstrate that solutions of 1–4 in SO 2, a uniquely polar nuclear spinfree solvent, reveal T2 values of up to 152(6) μs, comparable to the best molecular qubit candidates. Upon transitioning to vanadyl species from the tris(dithiolene) analogues, we observe a remarkable order of magnitude increase in 12, attributed to stronger solute–solvent interactions with the polar vanadium-oxo moiety. Simultaneously, we detect a small decrease in T2 for the vanadyl analogues relative to the tris(dithiolene) complexes. We attribute this decrease to the absence of one nuclear spinfree ligand, which served to shield the vanadium centers against solvent nuclear spins. Lastly, our results highlight new design principles for long T1 and T2 times by demonstrating the efficacy of ligand-based tuning of solute–solvent interactions.« less

Molecular Orientation in Two Component Vapor-Deposited Glasses: Effect of Substrate Temperature and Molecular Shape

NASA Astrophysics Data System (ADS)

Powell, Charles; Jiang, Jing; Walters, Diane; Ediger, Mark

Vapor-deposited glasses are widely investigated for use in organic electronics including the emitting layers of OLED devices. These materials, while macroscopically homogenous, have anisotropic packing and molecular orientation. By controlling this orientation, outcoupling efficiency can be increased by aligning the transition dipole moment of the light-emitting molecules parallel to the substrate. Light-emitting molecules are typically dispersed in a host matrix, as such, it is imperative to understand molecular orientation in two-component systems. In this study we examine two-component vapor-deposited films and the orientations of the constituent molecules using spectroscopic ellipsometry, UV-vis and IR spectroscopy. The role of temperature, composition and molecular shape as it effects molecular orientation is examined for mixtures of DSA-Ph in Alq3 and in TPD. Deposition temperature relative to the glass transition temperature of the two-component mixture is the primary controlling factor for molecular orientation. In mixtures of DSA-Ph in Alq3, the linear DSA-Ph has a horizontal orientation at low temperatures and slight vertical orientation maximized at 0.96Tg,mixture, analogous to one-component films.

Improved hole-injection and power efficiency of organic light-emitting diodes using an ultrathin cerium fluoride buffer layer

NASA Astrophysics Data System (ADS)

Lu, Hsin-Wei; Kao, Po-Ching; Chu, Sheng-Yuan

2016-09-01

In this study, the efficiency of organic light-emitting diodes (OLEDs) was enhanced by depositing a CeF3 film as an ultra-thin buffer layer between the ITO and NPB hole transport layer, with the structure configuration ITO/CeF3 (1 nm)/NPB (40 nm)/Alq3 (60 nm)/LiF (1 nm)/Al (150 nm). The enhancement mechanism was systematically investigated via several approaches. The work function increased from 4.8 eV (standard ITO electrode) to 5.2 eV (1-nm-thick UV-ozone treated CeF3 film deposited on the ITO electrode). The turn-on voltage decreased from 4.2 V to 4.0 V at 1 mA/cm2, the luminance increased from 7588 cd/m2 to 10820 cd/m2, and the current efficiency increased from 3.2 cd/A to 3.5 cd/A when the 1-nm-thick UV-ozone treated CeF3 film was inserted into the OLEDs.

GC/FT-IR ANALYSIS OF THE THERMALLY LABILE COMPOUND TRIS (2,3-DIBROMOPROPYL) PHOSPHATE

EPA Science Inventory

A fast and convenient GC method has been developed for a compound [tris(2,3-dibromopropyl)phosphate] that poses a difficult analytical problem for both GC (thermal instability/low volatility) and LC (not amenable to commonly available, sensitive detectors) analysis. his method em...

An effective in vitro and in vivo antileishmanial activity and mechanism of action of 8-hydroxyquinoline against Leishmania species causing visceral and tegumentary leishmaniasis.

PubMed

Costa Duarte, Mariana; dos Reis Lage, Letícia Martins; Lage, Daniela Pagliara; Mesquita, Juliana Tonini; Salles, Beatriz Cristina Silveira; Lavorato, Stefânia Neiva; Menezes-Souza, Daniel; Roatt, Bruno Mendes; Alves, Ricardo José; Tavares, Carlos Alberto Pereira; Tempone, André Gustavo; Coelho, Eduardo Antonio Ferraz

2016-02-15

The development of new therapeutic strategies to treat leishmaniasis has become a priority. In the present study, the antileishmanial activity of 8-hydroxyquinoline (8-HQN) was investigated against in vitro promastigotes and in vivo intra-macrophage amastigotes of three Leishmania species: Leishmania amazonensis, Leishmania infantum and Leishmania braziliensis. Studies were performed to establish the 50% Leishmania inhibitory concentration (IC50) of 8-HQN, as well as its 50% cytotoxic concentration (CC50) on murine macrophages and in human red blood cells. The inhibition of macrophages infection was also evaluated using parasites that were pre-treated with 8-HQN. The effects of this compound on nitric oxide (NO) production and in the mitochondrial membrane potential were also evaluated. Finally, the therapeutic efficacy of 8-HQN was assessed in a known murine model, L. amazonensis-chronically infected BALB/c mice. Our results showed that 8-HQN was effective against promastigote and amastigote stages of all tested Leishmania species, presenting a selectivity index of 328.0, 62.0 and 47.0 for L. amazonensis, L. infantum and L. braziliensis, respectively. It was effective in treating infected macrophages, as well as in preventing the infection of these cells using pre-treated parasites. In addition, 8-HQN caused an alteration in the mitochondrial membrane potential of the parasites. When administered at 10mg/kg body weight/day by subcutaneous route, this product was effective in reducing the lesion diameter, as well as the parasite load in evaluated tissues and organs of infected animals. The results showed the in vitro and in vivo efficacy of 8-HQN against three different Leishmania species causing tegumentary and/or visceral leishmaniasis, and it could well be used for future therapeutic optimization studies to treat leishmaniasis. Copyright © 2016 Elsevier B.V. All rights reserved.

Flame atomic absorption spectrometric determination of heavy metals in aqueous solution and surface water preceded by co-precipitation procedure with copper(II) 8-hydroxyquinoline

NASA Astrophysics Data System (ADS)

Ipeaiyeda, Ayodele Rotimi; Ayoade, Abisayo Ruth

2017-12-01

Co-precipitation procedure has widely been employed for preconcentration and separation of metal ions from the matrices of environmental samples. This is simply due to its simplicity, low consumption of separating solvent and short duration for analysis. Various organic ligands have been used for this purpose. However, there is dearth of information on the application of 8-hydroxyquinoline (8-HQ) as ligand and Cu(II) as carrier element. The use of Cu(II) is desirable because there is no contamination and background adsorption interference. Therefore, the objective of this study was to use 8-HQ in the presence of Cu(II) for coprecipitation of Cd(II), Co(II), Cr(III), Ni(II) and Pb(II) from standard solutions and surface water prior to their determinations by flame atomic absorption spectrometry (FAAS). The effects of pH, sample volume, amount of 8-HQ and Cu(II) and interfering ions on the recoveries of metal ions from standard solutions were monitored using FAAS. The water samples were treated with 8-HQ under the optimum experimental conditions and metal concentrations were determined by FAAS. The metal concentrations in water samples not treated with 8-HQ were also determined. The optimum recovery values for metal ions were higher than 85.0%. The concentrations (mg/L) of Co(II), Ni(II), Cr(III), and Pb(II) in water samples treated with 8-HQ were 0.014 ± 0.002, 0.03 ± 0.01, 0.04 ± 0.02 and 0.05 ± 0.02, respectively. These concentrations and those obtained without coprecipitation technique were significantly different. Coprecipitation procedure using 8-HQ as ligand and Cu(II) as carrier element enhanced the preconcentration and separation of metal ions from the matrix of water sample.

Characterizing filamentary switching in resistive memories (Presentation Recording)

NASA Astrophysics Data System (ADS)

Busby, Yan; Pireaux, Jean-Jacques

2015-09-01

Characterizing filamentary switching in resistive memories For many organic, inorganic and hybrid memory devices the resistive switching mechanism is well known to rely on filament formation [1]. This implies that localized conductive paths are established between the two terminal electrodes during the forming step. This filaments sustain the current flow when the memory is in the low conductive state and they can be ruptured and possibly re-formed for more than hundreds of I-V cycles. The nature and morphology of filaments has been long time debated especially for organic memories. The filament size, density and formation mechanism have been very challenging to be characterized, and need appropriate experimental techniques. However, filaments in organic memories have been recently identified and characterized by cross-section transmission electron microscopy (TEM), conductive-AFM, AFM-tomography and through depth profile analysis combining Time-of-flight secondary ions mass spectrometry (SIMS) and X-ray photoelectron spectroscopy (XPS). In particular, 3D spectroscopic images obtained with ToF-SIMS give access for the first time to filament formation process and rupture mechanism. From these results, a clear picture of the filament(s) dynamics during memory operation can be drawn. In this contribution, recent results showing filaments in memories based on different structures and architectures will be discussed. The memories are based on insulating polymers (polystyrene [2] and poly methyl methacrylate [3]), conductive polymers/nanocomposites (polyera N1400 with metal NPs [4]), and small semiconducting molecules (Tris(8-hydroxyquinolinato)aluminium - Alq3 [5]). The results show that resistive switching clearly involves the inhomogeneous metal diffusion in the organic layer taking place during the top electrode deposition and during memory operation. This may be of great relevance in many other organic electronics applications. REFERENCES [1] S. Nau, S. Sax, E.J.W. List-Kratochvil, Adv. Mater. 2014, 26, 2508-2513. [2] Y. Busby, N. Crespo-Monteiro, M. Girleanu, M. Brinkmann, O. Ersen, J.-J. Pireaux, Organic Electronics 2015, 16, 40-45. [3] C. Wolf, S. Nau, S. Sax, Y. Busby, J.-J. Pireaux, E.J.W. List-Kratochvil (under submission). [4] G. Casula, P. Cosseddu, Y. Busby, J.-J. Pireaux, M. Rosowski, B. Tkacz Szczesna, K. Soliwoda, G. Celichowski, J. Grobelny, J. Novák, R. Banerjee, F. Schreiber, A. Bonfiglio, Organic Electronics, 2015, 18, 17-23. [5] Y. Busby, S. Nau, S. Sax, E.J.W. List- Kratochvil, J. Novak, R. Banerjee, F. Schreiber, J.-J. Pireaux, (under submission)

Synthesis and antiplasmodial evaluation of novel (4-aminobutyloxy)quinolines.

PubMed

Vandekerckhove, Stéphanie; Müller, Christian; Vogt, Dieter; Lategan, Carmen; Smith, Peter J; Chibale, Kelly; De Kimpe, Norbert; D'hooghe, Matthias

2013-01-01

A variety of 5-, 6- and 8-(4-aminobutyloxy)quinolines as novel oxygen analogues of known 4- and 8-(4-aminobutylamino)quinoline antimalarial drugs was generated from hydroxyquinolines through a three-step approach with a rhodium-catalyzed hydroformylation as the key step. Antiplasmodial assays of these new quinolines revealed micromolar potency for all representatives against a chloroquine-sensitive strain of Plasmodium falciparum, and three compounds showed submicromolar activity against a chloroquine-resistant strain of P. falciparum with IC(50)-values ranging between 150 and 680 nM. Copyright © 2012 Elsevier Ltd. All rights reserved.

[Susceptibility of enterococci to natural and synthetic iron chelators].

PubMed

Lisiecki, Paweł; Mikucki, Jerzy

2002-01-01

A total of 79 strains of enterococci belonging to 10 species were tested for susceptibility to natural and synthetic iron chelators. All strains produced siderophores. These enterococci were susceptible to three synthetic iron chelators only: 8-hydroxyquinoline, disodium versenate (EDTA) and o-phenanthroline. They were resistant to all other synthetic chelators: ethylenediamine-di(o-hydroxyphenylacetic acid) (EDDHA), nitrilotriacetate, 2,2'-bipiridyl, salicylic acid, 8-hydroxy-5-sulphonic acid and to all natural chelators: ovotransferrine, human apotransferrine, horse apoferritine, desferrioxamine B, ferrichrome and rhodotorulic acid. The relations between susceptibility/resistance, iron assimilation and structure and stability constants of iron chelators were discussed.

Measurements of Parameters Controlling the Emissions of Organophosphate Flame Retardants in Indoor Environments.

PubMed

Liang, Yirui; Liu, Xiaoyu; Allen, Matthew R

2018-05-15

Emission of semivolatile organic compounds (SVOCs) from source materials usually occurs very slowly in indoor environments due to their low volatility. When the SVOC emission process is controlled by external mass transfer, the gas-phase concentration in equilibrium with the material ( y 0 ) is used as a key parameter to simplify the source models that are based on solid-phase diffusion. A material-air-material (M-A-M) configured microchamber method was developed to rapidly measure y 0 for a polyisocyanurate rigid foam material containing organophosphate flame retardants (OPRFs). The emission test was conducted in 44 mL microchambers for target OPFRs, including tris(2-chloroethyl) phosphate (CASRN: 115-96-8), tris(1-chloro-2-propyl) phosphate (CASRN: 13674-84-5), and tris(1,3-dichloro-2-propyl) phosphate (CASRN: 13674-87-8). In addition to the microchamber emission test, two other types of tests were conducted to determine y 0 for the same foam material: OPFR diffusive tube sampling tests from the OPFR source foam using stainless-steel thermal desorption tubes and sorption tests of OPFR on an OPFR-free foam in a 53 L small chamber. Comparison of parameters obtained from the three methods suggests that the discrepancy could be caused by a combination of theoretical, experimental, and computational differences. Based on the y 0 measurements, a linear relationship between the ratio of y 0 to saturated vapor pressure concentration and material-phase mass fractions has been found for phthalates and OPFRs.

Numerical simulation of optical and electronic properties for multilayer organic light-emitting diodes and its application in engineering education

NASA Astrophysics Data System (ADS)

Chang, Shu-Hsuan; Chang, Yung-Cheng; Yang, Cheng-Hong; Chen, Jun-Rong; Kuo, Yen-Kuang

2006-02-01

Organic light-emitting diodes (OLEDs) have been extensively developed in the past few years. The OLED displays have advantages over other displays, such as CRT, LCD, and PDP in thickness, weight, brightness, response time, viewing angle, contrast, driving power, flexibility, and capability of self-emission. In this work, the optical and electronic properties of multilayer OLED devices are numerically studied with an APSYS (Advanced Physical Model of Semiconductor Devices) simulation program. Specifically, the emission and absorption spectra of the Alq 3, DCM, PBD, and SA light-emitting layers, and energy band diagrams, electron-hole recombination rates, and current-voltage characteristics of the simulated OLED devices, typically with a multilayer structure of metal/Alq 3/EML/TPD/ITO constructed by Lim et al., are investigated and compared to the experimental results. The physical models utilized in this work are similar to those presented by Ruhstaller et al. and Hoffmann et al. The simulated results indicate that the emission spectra of the Alq 3, DCM, PBD, and SA light-emitting layers obtained in this study are in good agreement with those obtained experimentally by Zugang et al. Optimization of the optical and electronic performance of the multilayer OLED devices are attempted. In order to further promote the research results, the whole numerical simulation process for optimizing the design of OLED devices has been applied to a project-based course of OLED device design to enhance the students' skills in photonics device design at the Graduate Institute of Photonics of National Changhua University of Education in Taiwan. In the meantime, the effectiveness of the course has been proved by various assessments. The application of the results is a useful point of reference for the research on photonics device design and engineering education. Therefore, it proffers a synthetic effect between innovation and practical application.

Source amplitudes of NTS explosions inferred from Rayleigh waves at Albuquerque and Tucson. Topical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bache, T.C.; Rodi, W.L.; Mason, B.F.

1978-06-01

Comparing observed and synthetic seismograms, source amplitudes of NTS explosions are inferred from Rayleigh wave recordings from the WWSSN stations at Albuquerque, New Mexico (ALQ) and Tucson, Arizona (TUC). The potential influence of source complexities, particularly surface spallation and related phenomena, is studied in detail. As described in earlier work by Bache, Rodi and Harkrider, the earth model for the synthetic were converted from observations at ALQ and TUC. The agreement of observed and synthetic seismograms is quite good and is sensitive to important features of the source.

Improvement of parameters of freezing medium and freezing protocol for bull sperm using two osmotic supports.

PubMed

Chaveiro, A; Machado, L; Frijters, A; Engel, B; Woelders, H

2006-06-01

The aim of this study was to improve the freezing protocol of bull sperm, by investigating the influence on sperm viability after freeze/thawing of different freezing medium components, as well as the effect of cooling rates in the different stages of the cooling protocol, in single factor experiments. The experimental variables were: (1) salt-based versus a sugar-based medium (Tris versus sucrose); (2) glycerol concentration; (3) detergent (Equex) concentration; (4) presence of bicarbonate; (5) rate of cooling from 22 degrees C to holding temperature (CR1); (6) holding temperature (HT); (7) rate of cooling from holding temperature to -6 degrees C (CR2); (8) rate of cooling from -10 to -100 degrees C (CR3). All experiments were performed using five bulls per experiment (three ejaculates per bull). Sperm motility after freezing and thawing was assessed by CASA system, and sperm membrane integrity was assessed by flow cytometry. Sucrose-based medium did not offer a clear significant benefit compared to Tris medium. The concentration of Equex that gave the best results in Tris-based media group and sucrose-based media group was in a range between 2-7 and 4-7 g/l, respectively. In both media groups, a glycerol concentration of 800 mM was the best in any post-thaw viability parameters. In the Tris media group, the presence of bicarbonate had a negative effect on sperm viability. CR1 and CR2 had no significant effect on any of the post-thaw sperm viability parameters, but a CR1=0.2 degrees C/min and CR2=4 degrees C/min appeared to give better results in both media. The holding temperature (HT) that gave the best results was found to be in the range of 5-9 degrees C. There was a significant disadvantage of using a low CR3 of 10 degrees C/min, while 150 degrees C/min appeared to be the best cooling rate for either medium.

Advances in OLED-based oxygen sensors with structurally integrated OLED, sensor film, and thin-film Si photodetector

NASA Astrophysics Data System (ADS)

Ghosh, Debju; Shinar, Ruth; Cai, Yuankun; Zhou, Zhaoqun; Dalal, Vikram L.; Shinar, Joseph

2007-09-01

Steps towards the improvement of a compact photoluminescence (PL)-based sensor array that is fully structurally integrated are described. The approach is demonstrated for oxygen sensing, which can be monitored via its effect on the PL intensity I or decay time τ of oxygen-sensitive dyes such as Pt octaethylporphryn (PtOEP) and its Pd analog (PdOEP). The integrated components include (1) an organic light emitting device (OLED) excitation source, which is an array of coumarin-doped tris(quinolinolate) Al (Alq 3) pixels, (2) the sensor film, i.e., PdOEP embedded in polystyrene, and (3) the photodetector (PD), which is a plasma-enhanced CVD-grown p-i-n or n-i-p structure, based on amorphous or nanocrystalline (Si,Ge):H. These components are fabricated on common or separate substrates that are attached back-to-back, resulting in sensors with a thickness largely determined by that of the substrates. The fully integrated oxygen sensor is demonstrated first by fabricating each of the three components on a separate substrate. The PD was placed in front of a flow cell containing the sensor film, while the OLED array was "behind" the sensor film. This design showed the expected trend in monitoring different concentration of O II via their effect on I, with improved detection sensitivity achieved by shielding the electromagnetic noise synchronous with the pulsed OLED. The detection sensitivity using the I monitoring mode is expected to further increase by reducing the OLED tail emission. The issue of the OLED background can be eliminated by monitoring the oxygen concentration via its effect on τ, where the OLED is pulsed and τ is measured while the OLED is off. Steps therefore focused also on shortening the response time of the PDs, and understanding the factors affecting their speed. Development of a sensor array, where the PD pixels are fabricated between the OLED pixels on the same side of a common substrate, is also discussed.

Synthesis of tris- and tetrakis(pentafluoroethyl)silanes.

PubMed

Steinhauer, Simon; Bader, Julia; Stammler, Hans-Georg; Ignat'ev, Nikolai; Hoge, Berthold

2014-05-12

The synthesis and complete characterization of functional, highly Lewis acidic tris(pentafluoroethyl)silanes as well as tetrakis(perfluoroalkyl)silanes Si(C2F5)4 and Si(C2F5)3 CF3 by direct fluorination is described. The reaction of SiCl4 with LiC2F5 invariably affords (pentafluoroethyl)fluorosilicates. To avoid silicate formation by fluoride transfer from LiC2F5 the Lewis acidity of the silane has to be decreased by electron-donating substituents, such as dialkylamino groups. The easily accessible Si(C2F5)3 NEt2 is a valuable precursor for a series of tris(pentafluoroethyl)silanes. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Amended Description of the Genes for Synthesis of Actinomyces naeslundii T14V Type 1 Fimbriae and Associated Adhesin

DTIC Science & Technology

2007-05-07

type 2 fimbriae promote biofilm formation (14) through recognition of hostlike saccharide motifs in the surface polysaccharides of early colonizing...a NuPAGE Tris-acetate gradient gel (3 to 8%), transferred to a nitro- cellulose membrane, probed with MAb 8A against an epitope of FimP, and...inhibitors of bacterial adhesion: observations from the study of gram-positive bacteria that initiate biofilm formation on the tooth surface. Adv. Dent. Res

Effects of routine prophylactic vaccination or administration of aluminum adjuvant alone on allergen-specific serum IgE and IgG responses in allergic dogs.

PubMed

Tater, Kathy C; Jackson, Hilary A; Paps, Judy; Hammerberg, Bruce

2005-09-01

To determine the acute corn-specific serum IgE and IgG, total serum IgE, and clinical responses to s.c. administration of prophylactic vaccines and aluminum adjuvant in corn-allergic dogs. 20 allergic and 8 nonallergic dogs. 17 corn-allergic dogs were vaccinated. Eight clinically normal dogs also were vaccinated as a control group. Serum corn-specific IgE, corn-specific IgG, and total IgE concentrations were measured in each dog before vaccination and 1 and 3 weeks after vaccination by use of an ELISA. The corn-allergic dogs also had serum immunoglobulin concentrations measured at 8 and 9 weeks after vaccination. Twenty allergic dogs received a s.c. injection of aluminum adjuvant, and serum immunoglobulin concentrations were measured in each dog 1, 2, 3, 4, and 8 weeks after injection. The allergic dogs were examined during the 8 weeks after aluminum administration for clinical signs of allergic disease. The allergic dogs had significant increases in serum corn-specific IgE and IgG concentrations 1 and 3 weeks after vaccination but not 8 or 9 weeks after vaccination. Control dogs did not have a significant change in serum immunoglobulin concentrations after vaccination. After injection of aluminum adjuvant, the allergic dogs did not have a significant change in serum immunoglobulin concentrations or clinical signs. Allergen-specific IgE and IgG concentrations increase after prophylactic vaccination in allergic dogs but not in clinically normal dogs. Prophylactic vaccination of dogs with food allergies may affect results of serologic allergen-specific immunoglobulin testing performed within 8 weeks after vaccination.

Fatigue Crack-Growth Resistance of Aluminum Alloys Under Spectrum Loading. Volume 2. Aluminum Lithium Alloys.

DTIC Science & Technology

1985-12-01

Effects on Fatigue Crack Propagation in 2024 -T3 Aluminum Alloy ," Eng. Frac. Mech, * Vol. 8, 1976, p. 657...Retardation Behavior of 7075 * and 2024 Aluminum Alloys ," ASTNI STP 631, 1977. 89 hill". .A•, - . 34. Chanani, G.R., "Investigation of Effects of Saltwater...1.0 9,අ &M Ma ki-L6 &Ŗ &- La 06 lin "Ll Ull 1.25 "A Lm Wit Rtlc()FIV WtklLl’-"- ll*A FATIGUE CRACK-GROWTH RESISTANCE OF ALUMINUM ALLOYS

Crystal structures of fac-tri-chlorido-tris-(tri-methyl-phosphane-κP)rhodium(III) monohydrate and fac-tri-chlorido-tris-(tri-methyl-phosphane-κP)rhodium(III) methanol hemisolvate: rhodium structures that are isotypic with their iridium analogs.

PubMed

Merola, Joseph S; Franks, Marion A

2015-02-01

The crystal structures of two solvates of fac-tri-chlorido-tris-(tri-methyl-phosphane-κP)rhodium(III) are reported, i.e. one with water in the crystal lattice, fac-[RhCl3(Me3P)3]·H2O, and one with methanol in the crystal lattice, fac-[RhCl3(Me3P)3]·0.5CH3OH. These rhodium compounds exhibit distorted octahedral coordination spheres at the metal and are isotypic with the analogous iridium compounds previously reported by us [Merola et al. (2013 ▶). Polyhedron, 54, 67-73]. Comparison is made between the rhodium and iridium compounds, highlighting their isostructural relationships.

Can activated sludge treatments and advanced oxidation processes remove organophosphorus flame retardants?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cristale, Joyce; Ramos, Dayana D.; Dantas, Renato F.

2016-01-15

This study aims to determine the occurrence of 10 OPFRs (including chlorinated, nonchlorinated alkyl and aryl compounds) in influent, effluent wastewaters and partitioning into sludge of 5 wastewater treatment plants (WWTP) in Catalonia (Spain). All target OPFRs were detected in the WWTPs influents, and the total concentration ranged from 3.67 µg L{sup −1} to 150 µg L{sup −1}. During activated sludge treatment, most OPFRs were accumulated in the sludge at concentrations from 35.3 to 9980 ng g{sup −1} dw. Chlorinated compounds tris(2-chloroethyl) phosphate (TCEP), tris(2-chloroisopropyl) phosphate (TCIPP) and tris(2,3-dichloropropyl) phosphate (TDCPP) were not removed by the conventional activated sludge treatmentmore » and they were released by the effluents at approximately the same inlet concentration. On the contrary, aryl compounds tris(methylphenyl) phosphate (TMPP) and 2-ethylhexyl diphenyl phosphate (EHDP) together with alkyl tris(2-ethylhexyl) phosphate (TEHP) were not detected in any of the effluents. Advanced oxidation processes (UV/H{sub 2}O{sub 2} and O{sub 3}) were applied to investigate the degradability of recalcitrant OPFRs in WWTP effluents. Those detected in the effluent sample (TCEP, TCIPP, TDCPP, tributyl phosphate (TNBP), tri-iso-butyl phosphate (TIBP) and tris(2-butoxyethyl) phosphate (TBOEP)) had very low direct UV-C photolysis rates. TBOEP, TNBP and TIBP were degraded by UV/H{sub 2}O{sub 2} and O{sub 3}. Chlorinated compounds TCEP, TDCPP and TCIPP were the most recalcitrant OPFR to the advanced oxidation processes applied. The study provides information on the partitioning and degradability pathways of OPFR within conventional activated sludge WWTPs. - Highlights: • OPFRs were detected in wastewater and sludge of all studied WWTPs. • Alkyl and chloroalkyl phosphates were present in secondary treatment effluents. • TBOEP, TNBP and TIBP were degraded by UV/H{sub 2}O{sub 2} and O{sub 3} treatment. • TCEP, TCIPP and TDCPP were resistant to both secondary and tertiary treatment.« less

Vibrational spectroscopic studies of an organic non-linear optical crystal 8-hydroxyquinolinium picrate

NASA Astrophysics Data System (ADS)

Krishna Kumar, V.; Nagalakshmi, R.

2007-04-01

8-Hydroxyquinolinium picrate (8-HQP) was synthesized by the addition of equimolar quantities of 8-hydroxyquinoline (8-HQ) and picric acid (PA). Single crystals were grown from N, N dimethyl formamide (DMF) by restricted evaporation method at room temperature. The solubility of 8-HQP was determined in different solvents at various temperatures. The structural characterization of the grown crystals was carried out by X-ray diffraction. Vibrational modes were classified on the basis of group theoretical analysis and the spectral bands were compared with those of parent compounds in order to propose a tentative assignment by recording FT-IR, FT-Raman and polarized Raman spectra in different crystal orientations. The crystal possess lower cut-off at 230 nm and good transparency as confirmed by optical transmittance studies.

Controlled Growth of Rubrene Nanowires by Eutectic Melt Crystallization

NASA Astrophysics Data System (ADS)

Chung, Jeyon; Hyon, Jinho; Park, Kyung-Sun; Cho, Boram; Baek, Jangmi; Kim, Jueun; Lee, Sang Uck; Sung, Myung Mo; Kang, Youngjong

2016-03-01

Organic semiconductors including rubrene, Alq3, copper phthalocyanine and pentacene are crystallized by the eutectic melt crystallization. Those organic semiconductors form good eutectic systems with the various volatile crystallizable additives such as benzoic acid, salicylic acid, naphthalene and 1,3,5-trichlorobenzene. Due to the formation of the eutectic system, organic semiconductors having originally high melting point (Tm > 300 °C) are melted and crystallized at low temperature (Te = 40.8-133 °C). The volatile crystallizable additives are easily removed by sublimation. For a model system using rubrene, single crystalline rubrene nanowires are prepared by the eutectic melt crystallization and the eutectic-melt-assisted nanoimpinting (EMAN) technique. It is demonstrated that crystal structure and the growth direction of rubrene can be controlled by using different volatile crystallizable additives. The field effect mobility of rubrene nanowires prepared using several different crystallizable additives are measured and compared.

Further characterization of Bacillus subtilis antibiotic biosensors and their use for antibacterial mode-of-action studies.

PubMed

Mariner, Katherine R; Ooi, Nicola; Roebuck, Deborah; O'Neill, Alex J; Chopra, Ian

2011-04-01

We further examined the usefulness of previously reported Bacillus subtilis biosensors for antibacterial mode-of-action studies. The biosensors could not detect the tRNA synthetase inhibitors mupirocin, indolmycin, and borrelidin, some inhibitors of peptidoglycan synthesis, and most membrane-damaging agents. However, the biosensors confirmed the modes of action of several RNA polymerase inhibitors and DNA intercalators and provided new insights into the possible modes of action of ciprofloxacin, anhydrotetracycline, corralopyronin, 8-hydroxyquinoline, and juglone.

76 FR 33281 - 2-(Hydroxymethyl)-2-nitro-1,3-propanediol (Tris Nitro); Notice of Receipt of Requests for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-08

.../Vacation of Order To Amend Registrations To Terminate Certain Uses AGENCY: Environmental Protection Agency... provides that a registrant of a pesticide product may at any time request that any of its pesticide... issuing a Notice of Withdrawal/ Vacation of the ``2-(Hydroxymethyl)-2-nitro-1,3-propanediol (Tris Nitro...

Assessment of Damage Tolerance Requirements and Analysis. Volume 4. Raw Test Data

DTIC Science & Technology

1986-03-31

T3XX aluminum alloy . Four (4) product forms were selected: MATERIAL PRODUCT FORM THICKNESS (IN) 2024-T3 Sheet 0.090, 0.190 2024-T351 Plate 0.250 2024...T3511 Extruded Tee 0.190 2024-T3511 Extruded Angle 0.250 The material selected to represent bomber/transport/cargo aircraft is 7075- T6XX aluminum alloy ...aluminum alloys , respectively. The raw test data were processed in accordance with ASTM Standard E-8. All the tensile properties, except those marked

A Digital Temperature Control and Measurement System.

DTIC Science & Technology

1980-07-04

tubing. Vacuum connections, indicated by closed circles, are made with elastomer o-rings. 9.10 The outer vacuum can A is made entirely of aluminum , which...provides good thermal conductivity with minimal weight. Around the outer can is wrapped a 3/8" o.d. aluminum 3 tubing at one turn per inch. The first...through the aluminum tubing. The second stage, radiation shield B. is made entirely of coDper. A heater wire of #32 manganin wire with a total

Chemical effects in the Corrosion of Aluminum and Aluminum Alloys. A Bibliography

DTIC Science & Technology

1976-10-01

tances.II. Effect Of Pomegranate Juice And The Aqueous Extract Of Pomegranate Fruits And Tea leaves On The Corrosion Of Aluminum" The effect of the juices...T7651 tempers to exfoliation and stress- corrosion cracking . 1968-8 D.P. Doyle and H.P. Godard ,a) Tr. Mezhdunar. Kongr. Korroz. Metal, 4, 439-48, (1968...Tapper Brit. Corros. J., 3, 285-87, (1968) "Corrosion Of Aluminum" Summary of the literature of Al corrosion which includes stress- corrosion cracking

Identification of Bacillus anthracis by Using Monoclonal Antibody to Cell Wall Galactose-N-Acetylglucosamine Polysaccharide

DTIC Science & Technology

1990-02-01

which appear to be directed to an epitope associated with the galactose-N-acetyl-D- glucosamine polysaccharide. Both demonstrated specificity in their...liquid composed primarily of D-galactose and N-acetyl-D-glu - R medium (28) buffered with 50 mM Tris hydrochloride , pH cosamine (12, 13) (Gal-NAG...Ascites fluid (5 ml) was dialyzed (Cel-Line Associates, Inc., Newfield, N.J.). Suspensions against 20 mM Tris hydrochloride (pH 8.0) for 18 to 20 h, were