Multifamily Heat Pump Water Heater Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoeschele, M.; Weitzel, E.

2017-03-03

Although heat pump water heaters (HPWHs) have gained significant attention in recent years as a high efficiency electric water heating solution for single family homes, central HPWHs for commercial or multi-family applications are not as well documented in terms of measured performance and cost effectiveness. To evaluate this technology, the Alliance for Residential Building Innovation team monitored the performance of a 10.5 ton central HPWH installed on a student apartment building at the West Village Zero Net Energy Community in Davis, California. Monitoring data collected over a 16 month period were then used to validate a TRNSYS simulation model. Themore » TRNSYS model was then used to project performance in different climates using local electric rates. Results of the study indicate that after some initial commissioning issues, the HPWH operated reliably with an annual average efficiency of 2.12 (Coefficient of Performance). The observed efficiency was lower than the unit's rated efficiency, primarily due to the fact that the system rarely operated under steady-state conditions. Changes in the system configuration, storage tank sizing, and control settings would likely improve the observed field efficiency. Modeling results suggest significant energy savings relative to electric storage water heating systems (typical annual efficiencies around 0.90) providing for typical simple paybacks of six to ten years without any incentives. The economics versus gas water heating are currently much more challenging given the current low natural gas prices in much of the country. Increased market size for this technology would benefit cost effectiveness and spur greater technology innovation.« less

Multifamily Heat Pump Water Heater Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoeschele, M.; Weitzel, E.

2017-03-01

Although heat pump water heaters (HPWHs) have gained significant attention in recent years as a high efficiency electric water heating solution for single family homes, central HPWHs for commercial or multi-family applications are not as well documented in terms of measured performance and cost effectiveness. To evaluate this technology, the Alliance for Residential Building Innovation team monitored the performance of a 10.5 ton central HPWH installed on a student apartment building at the West Village Zero Net Energy Community in Davis, California. Monitoring data collected over a 16 month period were then used to validate a TRNSYS simulation model. Themore » TRNSYS model was then used to project performance in different climates using local electric rates. Results of the study indicate that after some initial commissioning issues, the HPWH operated reliably with an annual average efficiency of 2.12 (Coefficient of Performance). The observed efficiency was lower than the unit's rated efficiency, primarily due to the fact that the system rarely operated under steady-state conditions. Changes in the system configuration, storage tank sizing, and control settings would likely improve the observed field efficiency. Modeling results suggest significant energy savings relative to electric storage water heating systems (typical annual efficiencies around 0.90) providing for typical simple paybacks of six to ten years without any incentives. The economics versus gas water heating are currently much more challenging given the current low natural gas prices in much of the country. Increased market size for this technology would benefit cost effectiveness and spur greater technology innovation.« less

Analysis of wallboard containing a phase change material

NASA Astrophysics Data System (ADS)

Tomlinson, J. J.; Heberle, D. P.

Phase change materials (PCMs) used on the interior of buildings hold the promise for improved thermal performance by reducing the energy requirements for space conditioning and by improving thermal comfort by reducing temperature swings inside the building. Efforts are underway to develop a gypsum wallboard containing a hydrocarbon PCM. With a phase change temperature in the room temperature range, the PCM wallboard adds substantially to the thermal mass of the building while serving the same architectural function as conventional wallboard. To determine the thermal and economic performance of this PCM wallboard, the Transient Systems Simulation Program (TRNSYS) was modified to accommodate walls that are covered with PCM plasterboard, and to apportion the direct beam solar radiation to interior surfaces of a building. The modified code was used to simulate the performance of conventional and direct-gain passive solar residential-sized buildings with and without PCM wallboard. Space heating energy savings were determined as a function of PCM wallboard characteristics. Thermal comfort improvements in buildings containing the PCM were qualified in terms of energy savings. The report concludes with a present worth economic analysis of these energy savings and arrives at system costs and economic payback based on current costs of PCMs under study for the wallboard application.

Simulation and economic analysis of a liquid-based solar system with a direct-contact liquid-liquid heat exchanger, in comparison to a system with a conventional heat exchanger

NASA Astrophysics Data System (ADS)

Brothers, P.; Karaki, S.

Using a solar computer simulation package called TRNSYS, simulations of the direct contact liquid-liquid heat exchanger (DCLLHE) solar system and a system with conventional shell-and-tube heat exchanger were developed, based in part on performance measurements of the actual systems. The two systems were simulated over a full year on an hour-by-hour basis at five locations; Boston, Massachusetts, Charleston, South Carolina, Dodge City, Kansas, Madison, Wisconsin, and Phoenix, Arizona. Typically the direct-contact system supplies slightly more heat for domestic hot water and space heating in all locations and about 5 percentage points more cooling as compared to the conventional system. Using a common set of economic parameters and the appropriate federal and state income tax credits, as well as property tax legislation for solar systems in the corresponding states, the results of the study indicate for heating-only systems, the DCLLHE system has a slight life-cycle cost disadvantage compared to the conventional system. For combined solar heating and cooling systems, the DCLLHE has a slight life-cycle cost advantage which varies with location and amounts to one to three percent difference from the conventional system.

Analysis of wallboard containing a phase change material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomlinson, J.J.; Heberle, D.P.

1990-01-01

Phase change materials (PCMs) used on the interior of buildings hold the promise for improved thermal performance by reducing the energy requirements for space conditioning and by improving thermal comfort by reducing temperature swings inside the building. Efforts are underway to develop a gypsum wallboard containing a hydrocarbon PCM. With a phase change temperature in the room temperature range, the PCM wallboard adds substantially to the thermal mass of the building while serving the same architectural function as conventional wallboard. To determine the thermal and economic performance of this PCM wallboard, the Transient Systems Simulation Program (TRNSYS) was modified tomore » accommodate walls that are covered with PCM plasterboard, nd to apportion the direct beam solar radiation to interior surfaces of a building. The modified code was used to simulate the performance of conventional and direct-gain passive solar residential-sized buildings with and without PCM wallboard. Space heating energy savings were determined as a function of PCM wallboard characteristics. Thermal comfort improvements in buildings containing the PCM were qualified in terms of energy savings. The report concludes with a present worth economic analysis of these energy savings and arrives at system costs and economic payback based on current costs of PCMs under study for the wallboard application. 5 refs., 4 figs., 4 tabs.« less

Determination of Vertical Borehole and Geological Formation Properties using the Crossed Contour Method.

PubMed

Leyde, Brian P; Klein, Sanford A; Nellis, Gregory F; Skye, Harrison

2017-03-01

This paper presents a new method called the Crossed Contour Method for determining the effective properties (borehole radius and ground thermal conductivity) of a vertical ground-coupled heat exchanger. The borehole radius is used as a proxy for the overall borehole thermal resistance. The method has been applied to both simulated and experimental borehole Thermal Response Test (TRT) data using the Duct Storage vertical ground heat exchanger model implemented in the TRansient SYstems Simulation software (TRNSYS). The Crossed Contour Method generates a parametric grid of simulated TRT data for different combinations of borehole radius and ground thermal conductivity in a series of time windows. The error between the average of the simulated and experimental bore field inlet and outlet temperatures is calculated for each set of borehole properties within each time window. Using these data, contours of the minimum error are constructed in the parameter space of borehole radius and ground thermal conductivity. When all of the minimum error contours for each time window are superimposed, the point where the contours cross (intersect) identifies the effective borehole properties for the model that most closely represents the experimental data in every time window and thus over the entire length of the experimental data set. The computed borehole properties are compared with results from existing model inversion methods including the Ground Property Measurement (GPM) software developed by Oak Ridge National Laboratory, and the Line Source Model.

Building America Case Study: Assessment of a Hybrid Retrofit Gas Water Heater

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. Hoeschele, E. Weitzel, C. Backman

This project completed a modeling evaluation of a hybrid gas water heater that combines a reduced capacity tankless unit with a downsized storage tank. This product would meet a significant market need by providing a higher efficiency gas water heater solution for retrofit applications while maintaining compatibility with the half-inch gas lines and standard B vents found in most homes. The TRNSYS simulation tool was used to model a base case 0.60 EF atmospheric gas storage water, a 0.82 EF non-condensing gas tankless water heater, an existing (high capacity) hybrid unit on the market, and an alternative hybrid unit withmore » lower storage volume and reduced gas input requirements.« less

Operative air temperature data for different measures applied on a building envelope in warm climate.

PubMed

Baglivo, Cristina; Congedo, Paolo Maria

2018-04-01

Several technical combinations have been evaluated in order to design high energy performance buildings for the warm climate. The analysis has been developed in several steps, avoiding the use of HVAC systems. The methodological approach of this study is based on a sequential search technique and it is shown on the paper entitled "Envelope Design Optimization by Thermal Modeling of a Building in a Warm Climate" [1]. The Operative Air Temperature trends (TOP), for each combination, have been plotted through a dynamic simulation performed using the software TRNSYS 17 (a transient system simulation program, University of Wisconsin, Solar Energy Laboratory, USA, 2010). Starting from the simplest building configuration consisting of 9 rooms (equal-sized modules of 5 × 5 m 2 ), the different building components are sequentially evaluated until the envelope design is optimized. The aim of this study is to perform a step-by-step simulation, simplifying as much as possible the model without making additional variables that can modify their performances. Walls, slab-on-ground floor, roof, shading and windows are among the simulated building components. The results are shown for each combination and evaluated for Brindisi, a city in southern Italy having 1083 degrees day, belonging to the national climatic zone C. The data show the trends of the TOP for each measure applied in the case study for a total of 17 combinations divided into eight steps.

Determination of Vertical Borehole and Geological Formation Properties using the Crossed Contour Method

PubMed Central

Leyde, Brian P.; Klein, Sanford A; Nellis, Gregory F.; Skye, Harrison

2017-01-01

This paper presents a new method called the Crossed Contour Method for determining the effective properties (borehole radius and ground thermal conductivity) of a vertical ground-coupled heat exchanger. The borehole radius is used as a proxy for the overall borehole thermal resistance. The method has been applied to both simulated and experimental borehole Thermal Response Test (TRT) data using the Duct Storage vertical ground heat exchanger model implemented in the TRansient SYstems Simulation software (TRNSYS). The Crossed Contour Method generates a parametric grid of simulated TRT data for different combinations of borehole radius and ground thermal conductivity in a series of time windows. The error between the average of the simulated and experimental bore field inlet and outlet temperatures is calculated for each set of borehole properties within each time window. Using these data, contours of the minimum error are constructed in the parameter space of borehole radius and ground thermal conductivity. When all of the minimum error contours for each time window are superimposed, the point where the contours cross (intersect) identifies the effective borehole properties for the model that most closely represents the experimental data in every time window and thus over the entire length of the experimental data set. The computed borehole properties are compared with results from existing model inversion methods including the Ground Property Measurement (GPM) software developed by Oak Ridge National Laboratory, and the Line Source Model. PMID:28785125

Using Coupled Energy, Airflow and IAQ Software (TRNSYS/CONTAM) to Evaluate Building Ventilation Strategies.

PubMed

Dols, W Stuart; Emmerich, Steven J; Polidoro, Brian J

2016-03-01

Building energy analysis tools are available in many forms that provide the ability to address a broad spectrum of energy-related issues in various combinations. Often these tools operate in isolation from one another, making it difficult to evaluate the interactions between related phenomena and interacting systems, forcing oversimplified assumptions to be made about various phenomena that could otherwise be addressed directly with another tool. One example of such interdependence is the interaction between heat transfer, inter-zone airflow and indoor contaminant transport. In order to better address these interdependencies, the National Institute of Standards and Technology (NIST) has developed an updated version of the multi-zone airflow and contaminant transport modelling tool, CONTAM, along with a set of utilities to enable coupling of the full CONTAM model with the TRNSYS simulation tool in a more seamless manner and with additional capabilities that were previously not available. This paper provides an overview of these new capabilities and applies them to simulating a medium-size office building. These simulations address the interaction between whole-building energy, airflow and contaminant transport in evaluating various ventilation strategies including natural and demand-controlled ventilation. CONTAM has been in practical use for many years allowing building designers, as well as IAQ and ventilation system analysts, to simulate the complex interactions between building physical layout and HVAC system configuration in determining building airflow and contaminant transport. It has been widely used to design and analyse smoke management systems and evaluate building performance in response to chemical, biological and radiological events. While CONTAM has been used to address design and performance of buildings implementing energy conserving ventilation systems, e.g., natural and hybrid, this new coupled simulation capability will enable users to apply the tool to couple CONTAM with existing energy analysis software to address the interaction between indoor air quality considerations and energy conservation measures in building design and analysis. This paper presents two practical case studies using the coupled modelling tool to evaluate IAQ performance of a CO 2 -based demand-controlled ventilation system under different levels of building envelope airtightness and the design and analysis of a natural ventilation system.

Using Coupled Energy, Airflow and IAQ Software (TRNSYS/CONTAM) to Evaluate Building Ventilation Strategies

PubMed Central

Dols, W. Stuart.; Emmerich, Steven J.; Polidoro, Brian J.

2016-01-01

Building energy analysis tools are available in many forms that provide the ability to address a broad spectrum of energy-related issues in various combinations. Often these tools operate in isolation from one another, making it difficult to evaluate the interactions between related phenomena and interacting systems, forcing oversimplified assumptions to be made about various phenomena that could otherwise be addressed directly with another tool. One example of such interdependence is the interaction between heat transfer, inter-zone airflow and indoor contaminant transport. In order to better address these interdependencies, the National Institute of Standards and Technology (NIST) has developed an updated version of the multi-zone airflow and contaminant transport modelling tool, CONTAM, along with a set of utilities to enable coupling of the full CONTAM model with the TRNSYS simulation tool in a more seamless manner and with additional capabilities that were previously not available. This paper provides an overview of these new capabilities and applies them to simulating a medium-size office building. These simulations address the interaction between whole-building energy, airflow and contaminant transport in evaluating various ventilation strategies including natural and demand-controlled ventilation. Practical Application CONTAM has been in practical use for many years allowing building designers, as well as IAQ and ventilation system analysts, to simulate the complex interactions between building physical layout and HVAC system configuration in determining building airflow and contaminant transport. It has been widely used to design and analyse smoke management systems and evaluate building performance in response to chemical, biological and radiological events. While CONTAM has been used to address design and performance of buildings implementing energy conserving ventilation systems, e.g., natural and hybrid, this new coupled simulation capability will enable users to apply the tool to couple CONTAM with existing energy analysis software to address the interaction between indoor air quality considerations and energy conservation measures in building design and analysis. This paper presents two practical case studies using the coupled modelling tool to evaluate IAQ performance of a CO2-based demand-controlled ventilation system under different levels of building envelope airtightness and the design and analysis of a natural ventilation system. PMID:27099405

Energy demand and thermal comfort of HVAC systems with thermally activated building systems as a function of user profile

NASA Astrophysics Data System (ADS)

Pałaszyńska, Katarzyna; Bandurski, Karol; Porowski, Mieczysław

2017-11-01

Thermally Activated Building Systems (TABS) are a way to use building structure as a thermal energy storage. As a result, renewable energy sources may be used more efficiently. The paper presents numerical analysis of a HVAC system with TABS energy demand and indoor thermal comfort of a representative room in a non-residential building (governmental, commercial, educational). The purpose of analysis is to investigate the influence of a user profile on system performance. The time span of the analysis is one year - a typical meteorological year. The model was prepared using a generally accepted simulation tool - TRNSYS 17. The results help to better understand the interaction of a user profile with TABS. Therefore they are important for the development of optimal control algorithms for energy efficient buildings equipped with such systems.

Simulation of energy- efficient building prototype using different insulating materials

NASA Astrophysics Data System (ADS)

Ouhaibi, Salma; Belouaggadia, Naoual; Lbibb, Rachid; Ezzine, Mohammed

2018-05-01

The objective of this work is to analyze the energetic efficiency of an individual building including an area of 130 m2 multi-zone, located in the region of FEZ which is characterized by a very hot and dry climate in summer and a quite cold one in winter, by incorporating insulating materials. This study was performed using TRNSYS V16 simulation software during a typical year of the FEZ region. Our simulation consists in developing a comparative study of two types of polystyrene and silica-aerogel insulation materials, in order to determine the best thermal performance. The results show that the thermal insulation of the building envelope is among the most effective solutions that give a significant reduction in energy requirements. Similarly, the use of silica-aerogels gives a good thermal performance, and therefore a good energy gain.

Research on the operation control strategy of the cooling ceiling combined with fresh air system

NASA Astrophysics Data System (ADS)

Huang, Tao; Li, Hao

2018-03-01

The cooling ceiling combined with independent fresh air system was built by TRNSYS. And the cooling effects of the air conditioning system of an office in Beijing in a summer typical day were simulated. Based on the “variable temperature” control strategy, the operation strategy of “variable air volume auxiliary adjustment” was put forward. The variation of the indoor temperature, the indoor humidity, the temperature of supplying water and the temperature of returning water were simulated under the two control strategies. The energy consumption of system during the whole summer was compared by utilizing the two control strategies, and the indoor thermal comfort was analyzed. The optimal control strategy was proposed under the condition that the condensation on the surface of the cooling ceiling is not occurred and the indoor thermal comfort is satisfied.

A neural network controller for hydronic heating systems of solar buildings.

PubMed

Argiriou, Athanassios A; Bellas-Velidis, Ioannis; Kummert, Michaël; André, Philippe

2004-04-01

An artificial neural network (ANN)-based controller for hydronic heating plants of buildings is presented. The controller has forecasting capabilities: it includes a meteorological module, forecasting the ambient temperature and solar irradiance, an indoor temperature predictor module, a supply temperature predictor module and an optimizing module for the water supply temperature. All ANN modules are based on the Feed Forward Back Propagation (FFBP) model. The operation of the controller has been tested experimentally, on a real-scale office building during real operating conditions. The operation results were compared to those of a conventional controller. The performance was also assessed via numerical simulation. The detailed thermal simulation tool for solar systems and buildings TRNSYS was used. Both experimental and numerical results showed that the expected percentage of energy savings with respect to a conventional controller is of about 15% under North European weather conditions.

Thermal Performance Analysis of Solar Collectors Installed for Combisystem in the Apartment Building

NASA Astrophysics Data System (ADS)

Žandeckis, A.; Timma, L.; Blumberga, D.; Rochas, C.; Rošā, M.

2012-01-01

The paper focuses on the application of wood pellet and solar combisystem for space heating and hot water preparation at apartment buildings under the climate of Northern Europe. A pilot project has been implemented in the city of Sigulda (N 57° 09.410 E 024° 52.194), Latvia. The system was designed and optimised using TRNSYS - a dynamic simulation tool. The pilot project was continuously monitored. To the analysis the heat transfer fluid flow rate and the influence of the inlet temperature on the performance of solar collectors were subjected. The thermal performance of a solar collector loop was studied using a direct method. A multiple regression analysis was carried out using STATGRAPHICS Centurion 16.1.15 with the aim to identify the operational and weather parameters of the system which cause the strongest influence on the collector's performance. The parameters to be used for the system's optimisation have been evaluated.

Mississippi Curriculum Framework for Computer Information Systems Technology. Computer Information Systems Technology (Program CIP: 52.1201--Management Information Systems & Business Data). Computer Programming (Program CIP: 52.1201). Network Support (Program CIP: 52.1290--Computer Network Support Technology). Postsecondary Programs.

ERIC Educational Resources Information Center

Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

This document, which is intended for use by community and junior colleges throughout Mississippi, contains curriculum frameworks for two programs in the state's postsecondary-level computer information systems technology cluster: computer programming and network support. Presented in the introduction are program descriptions and suggested course…

78 FR 73195 - Privacy Act of 1974: CMS Computer Matching Program Match No. 2013-01; HHS Computer Matching...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-05

.... Description of the Matching Program A. General The Computer Matching and Privacy Protection Act of 1988 (Pub... 1974: CMS Computer Matching Program Match No. 2013-01; HHS Computer Matching Program Match No. 1312...). ACTION: Notice of Computer Matching Program (CMP). SUMMARY: In accordance with the requirements of the...

Handheld Computer Use in U.S. Family Practice Residency Programs

PubMed Central

Criswell, Dan F.; Parchman, Michael L.

2002-01-01

Objective: The purpose of the study was to evaluate the uses of handheld computers (also called personal digital assistants, or PDAs) in family practice residency programs in the United States. Study Design: In November 2000, the authors mailed a questionnaire to the program directors of all American Academy of Family Physicians (AAFP) and American College of Osteopathic Family Practice (ACOFP) residency programs in the United States. Measurements: Data and patterns of the use and non-use of handheld computers were identified. Results: Approximately 50 percent (306 of 610) of the programs responded to the survey. Two thirds of the programs reported that handheld computers were used in their residencies, and an additional 14 percent had plans for implementation within 24 months. Both the Palm and the Windows CE operating systems were used, with the Palm operating system the most common. Military programs had the highest rate of use (8 of 10 programs, 80 percent), and osteopathic programs had the lowest (23 of 55 programs, 42 percent). Of programs that reported handheld computer use, 45 percent had required handheld computer applications that are used uniformly by all users. Funding for handheld computers and related applications was non-budgeted in 76percent of the programs in which handheld computers were used. In programs providing a budget for handheld computers, the average annual budget per user was $461.58. Interested faculty or residents, rather than computer information services personnel, performed upkeep and maintenance of handheld computers in 72 percent of the programs in which the computers are used. In addition to the installed calendar, memo pad, and address book, the most common clinical uses of handheld computers in the programs were as medication reference tools, electronic textbooks, and clinical computational or calculator-type programs. Conclusions: Handheld computers are widely used in family practice residency programs in the United States. Although handheld computers were designed as electronic organizers, in family practice residencies they are used as medication reference tools, electronic textbooks, and clinical computational programs and to track activities that were previously associated with desktop database applications. PMID:11751806

Handheld computer use in U.S. family practice residency programs.

PubMed

Criswell, Dan F; Parchman, Michael L

2002-01-01

The purpose of the study was to evaluate the uses of handheld computers (also called personal digital assistants, or PDAs) in family practice residency programs in the United States. In November 2000, the authors mailed a questionnaire to the program directors of all American Academy of Family Physicians (AAFP) and American College of Osteopathic Family Practice (ACOFP) residency programs in the United States. Data and patterns of the use and non-use of handheld computers were identified. Approximately 50 percent (306 of 610) of the programs responded to the survey. Two thirds of the programs reported that handheld computers were used in their residencies, and an additional 14 percent had plans for implementation within 24 months. Both the Palm and the Windows CE operating systems were used, with the Palm operating system the most common. Military programs had the highest rate of use (8 of 10 programs, 80 percent), and osteopathic programs had the lowest (23 of 55 programs, 42 percent). Of programs that reported handheld computer use, 45 percent had required handheld computer applications that are used uniformly by all users. Funding for handheld computers and related applications was non-budgeted in 76percent of the programs in which handheld computers were used. In programs providing a budget for handheld computers, the average annual budget per user was 461.58 dollars. Interested faculty or residents, rather than computer information services personnel, performed upkeep and maintenance of handheld computers in 72 percent of the programs in which the computers are used. In addition to the installed calendar, memo pad, and address book, the most common clinical uses of handheld computers in the programs were as medication reference tools, electronic textbooks, and clinical computational or calculator-type programs. Handheld computers are widely used in family practice residency programs in the United States. Although handheld computers were designed as electronic organizers, in family practice residencies they are used as medication reference tools, electronic textbooks, and clinical computational programs and to track activities that were previously associated with desktop database applications.

The RANDOM computer program: A linear congruential random number generator

NASA Technical Reports Server (NTRS)

Miles, R. F., Jr.

1986-01-01

The RANDOM Computer Program is a FORTRAN program for generating random number sequences and testing linear congruential random number generators (LCGs). The linear congruential form of random number generator is discussed, and the selection of parameters of an LCG for a microcomputer described. This document describes the following: (1) The RANDOM Computer Program; (2) RANDOM.MOD, the computer code needed to implement an LCG in a FORTRAN program; and (3) The RANCYCLE and the ARITH Computer Programs that provide computational assistance in the selection of parameters for an LCG. The RANDOM, RANCYCLE, and ARITH Computer Programs are written in Microsoft FORTRAN for the IBM PC microcomputer and its compatibles. With only minor modifications, the RANDOM Computer Program and its LCG can be run on most micromputers or mainframe computers.

DIALOG: An executive computer program for linking independent programs

NASA Technical Reports Server (NTRS)

Glatt, C. R.; Hague, D. S.; Watson, D. A.

1973-01-01

A very large scale computer programming procedure called the DIALOG executive system was developed for the CDC 6000 series computers. The executive computer program, DIALOG, controls the sequence of execution and data management function for a library of independent computer programs. Communication of common information is accomplished by DIALOG through a dynamically constructed and maintained data base of common information. Each computer program maintains its individual identity and is unaware of its contribution to the large scale program. This feature makes any computer program a candidate for use with the DIALOG executive system. The installation and uses of the DIALOG executive system are described.

A CAD (Classroom Assessment Design) of a Computer Programming Course

ERIC Educational Resources Information Center

Hawi, Nazir S.

2012-01-01

This paper presents a CAD (classroom assessment design) of an entry-level undergraduate computer programming course "Computer Programming I". CAD has been the product of a long experience in teaching computer programming courses including teaching "Computer Programming I" 22 times. Each semester, CAD is evaluated and modified…

Comparison of two computer programs by predicting turbulent mixing of helium in a ducted supersonic airstream

NASA Technical Reports Server (NTRS)

Pan, Y. S.; Drummond, J. P.; Mcclinton, C. R.

1978-01-01

Two parabolic flow computer programs, SHIP (a finite-difference program) and COMOC (a finite-element program), are used for predicting three-dimensional turbulent reacting flow fields in supersonic combustors. The theoretical foundation of the two computer programs are described, and then the programs are applied to a three-dimensional turbulent mixing experiment. The cold (nonreacting) flow experiment was performed to study the mixing of helium jets with a supersonic airstream in a rectangular duct. Surveys of the flow field at an upstream were used as the initial data by programs; surveys at a downstream station provided comparison to assess program accuracy. Both computer programs predicted the experimental results and data trends reasonably well. However, the comparison between the computations from the two programs indicated that SHIP was more accurate in computation and more efficient in both computer storage and computing time than COMOC.

Computer program CDCID: an automated quality control program using CDC update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singer, G.L.; Aguilar, F.

1984-04-01

A computer program, CDCID, has been developed in coordination with a quality control program to provide a highly automated method of documenting changes to computer codes at EG and G Idaho, Inc. The method uses the standard CDC UPDATE program in such a manner that updates and their associated documentation are easily made and retrieved in various formats. The method allows each card image of a source program to point to the document which describes it, who created the card, and when it was created. The method described is applicable to the quality control of computer programs in general. Themore » computer program described is executable only on CDC computing systems, but the program could be modified and applied to any computing system with an adequate updating program.« less

Application Portable Parallel Library

NASA Technical Reports Server (NTRS)

Cole, Gary L.; Blech, Richard A.; Quealy, Angela; Townsend, Scott

1995-01-01

Application Portable Parallel Library (APPL) computer program is subroutine-based message-passing software library intended to provide consistent interface to variety of multiprocessor computers on market today. Minimizes effort needed to move application program from one computer to another. User develops application program once and then easily moves application program from parallel computer on which created to another parallel computer. ("Parallel computer" also include heterogeneous collection of networked computers). Written in C language with one FORTRAN 77 subroutine for UNIX-based computers and callable from application programs written in C language or FORTRAN 77.

DIALOG: An executive computer program for linking independent programs

NASA Technical Reports Server (NTRS)

Glatt, C. R.; Hague, D. S.; Watson, D. A.

1973-01-01

A very large scale computer programming procedure called the DIALOG Executive System has been developed for the Univac 1100 series computers. The executive computer program, DIALOG, controls the sequence of execution and data management function for a library of independent computer programs. Communication of common information is accomplished by DIALOG through a dynamically constructed and maintained data base of common information. The unique feature of the DIALOG Executive System is the manner in which computer programs are linked. Each program maintains its individual identity and as such is unaware of its contribution to the large scale program. This feature makes any computer program a candidate for use with the DIALOG Executive System. The installation and use of the DIALOG Executive System are described at Johnson Space Center.

Programming the social computer.

PubMed

Robertson, David; Giunchiglia, Fausto

2013-03-28

The aim of 'programming the global computer' was identified by Milner and others as one of the grand challenges of computing research. At the time this phrase was coined, it was natural to assume that this objective might be achieved primarily through extending programming and specification languages. The Internet, however, has brought with it a different style of computation that (although harnessing variants of traditional programming languages) operates in a style different to those with which we are familiar. The 'computer' on which we are running these computations is a social computer in the sense that many of the elementary functions of the computations it runs are performed by humans, and successful execution of a program often depends on properties of the human society over which the program operates. These sorts of programs are not programmed in a traditional way and may have to be understood in a way that is different from the traditional view of programming. This shift in perspective raises new challenges for the science of the Web and for computing in general.

Gender Differences in the Use of Computers, Programming, and Peer Interactions in Computer Science Classrooms

ERIC Educational Resources Information Center

Stoilescu, Dorian; Egodawatte, Gunawardena

2010-01-01

Research shows that female and male students in undergraduate computer science programs view computer culture differently. Female students are interested more in the use of computers than in doing programming, whereas male students see computer science mainly as a programming activity. The overall purpose of our research was not to find new…

Numerical study of the vertical shading devices effect on the thermal performance of promotional apartments in hot dry climate of Algeria

NASA Astrophysics Data System (ADS)

Berkouk, Djihed; Bouzir, Tallal Abdel Karim; Mazouz, Said

2018-05-01

The bioclimatic architecture considers the local climatic conditions in order to reconcile maximally the comfort condition of the occupants. Through the several simulations effectuated by the TRNSYS software, this paper shows that the new architecture produced in the south of Algeria following the northern cities tendency is not fully adapted to the hot dry climate of the southern regions, such as the city of Biskra. In these regions, the passive techniques design influence strongly on the thermal architectural space performance. In this regard, diverse of the vertical shading devices size were proposed to evaluate the impact of this passive technique on the thermal performance of the promotional apartments situated in the city of Biskra. The comparative analysis between the simulation results says that the effectiveness of the vertical shading devices on the thermal performance spaces is reducing the indoor air temperature during the summer period. In addition, this analysis shows that promotional apartments are unsuitable for the desert climate.

Simulation of the thermal performance of a hybrid solar-assisted ground-source heat pump system in a school building

NASA Astrophysics Data System (ADS)

Androulakis, N. D.; Armen, K. G.; Bozis, D. A.; Papakostas, K. T.

2018-04-01

A hybrid solar-assisted ground-source heat pump (SAGSHP) system was designed, in the frame of an energy upgrade study, to serve as a heating system in a school building in Greece. The main scope of this study was to examine techniques to reduce the capacity of the heating equipment and to keep the primary energy consumption low. Simulations of the thermal performance of both the building and of five different heating system configurations were performed by using the TRNSYS software. The results are presented in this work and show that the hybrid SAGSHP system displays the lower primary energy consumption among the systems examined. A conventional ground-source heat pump system has the same primary energy consumption, while the heat pump's capacity is double and the ground heat exchanger 2.5 times longer. This work also highlights the contribution of simulation tools to the design of complex heating systems with renewable energy sources.

Simulation and Evaluation of Small Scale Solar Power Tower Performance under Malaysia Weather Conditions

NASA Astrophysics Data System (ADS)

Gamil, A. M.; Gilani, S. I.; Al-Kayiem, H. H.

2013-06-01

Solar energy is the most available, clean, and inexpensive source of energy among the other renewable sources of energy. Malaysia is an encouraging location for the development of solar energy systems due to abundant sunshine (10 hours daily with average solar energy received between 1400 and 1900 kWh/m2). In this paper the design of heliostat field of 3 dual-axis heliostat units located in Ipoh, Malaysia is introduced. A mathematical model was developed to estimate the sun position and calculate the cosine losses in the field. The study includes calculating the incident solar power to a fixed target on the tower by analysing the tower height and ground distance between the heliostat and the tower base. The cosine efficiency was found for each heliostat according to the sun movement. TRNSYS software was used to simulate the cosine efficiencies and field hourly incident solar power input to the fixed target. The results show the heliostat field parameters and the total incident solar input to the receiver.

Potential for large-scale solar collector system to offset carbon-based heating in the Ontario greenhouse sector

NASA Astrophysics Data System (ADS)

Semple, Lucas M.; Carriveau, Rupp; Ting, David S.-K.

2018-04-01

In the Ontario greenhouse sector the misalignment of available solar radiation during the summer months and large heating demand during the winter months makes solar thermal collector systems an unviable option without some form of seasonal energy storage. Information obtained from Ontario greenhouse operators has shown that over 20% of annual natural gas usage occurs during the summer months for greenhouse pre-heating prior to sunrise. A transient model of the greenhouse microclimate and indoor conditioning systems is carried out using TRNSYS software and validated with actual natural gas usage data. A large-scale solar thermal collector system is then incorporated and found to reduce the annual heating energy demand by approximately 35%. The inclusion of the collector system correlates to a reduction of about 120 tonnes of CO2 equivalent emissions per acre of greenhouse per year. System payback period is discussed considering the benefits of a future Ontario carbon tax.

Simulation of floor heating in a combined solar-biomass system integrated in a public bathhouse located in Marrakech

NASA Astrophysics Data System (ADS)

Krarouch, M.; Hamdi, H.; Lamghari, S.; Outzourhit, A.

2018-05-01

This study was conducted in the framework of the HYBRID-BATH project aiming at improving the energy efficiency of traditional Hammams (Turkish baths) and the reduction of the use of wood energy and therefore of greenhouse gases emissions. The present work focuses on the energetic performance of a two-room Hammam located in Marrakech. The rooms were heated by the ground using a hybrid system Micro-CSP/biomass boiler. The dynamic simulation of the system (Hammam coupled with the hybrid system Micro-CSP/biomass boiler) was conducted using TRNSYS18 software. The parametric study was performed on a Typical Meteorological Year data (TMY). This study is devoted to presenting the results of the dynamic simulation of a part of the Hammam investigated, in order to optimize the underfloor heating system. The models and the results of the simulations will be validated by comparisons with experimental results. The main objective is to optimize the operation of such system and to improve its performance.

41 CFR 105-64.110 - When may GSA establish computer matching programs?

Code of Federal Regulations, 2013 CFR

2013-07-01

... computer matching programs? 105-64.110 Section 105-64.110 Public Contracts and Property Management Federal... GSA establish computer matching programs? (a) System managers will establish computer matching... direction of the GSA Data Integrity Board that will be established when and if computer matching programs...

41 CFR 105-64.110 - When may GSA establish computer matching programs?

Code of Federal Regulations, 2012 CFR

2012-01-01

... computer matching programs? 105-64.110 Section 105-64.110 Public Contracts and Property Management Federal... GSA establish computer matching programs? (a) System managers will establish computer matching... direction of the GSA Data Integrity Board that will be established when and if computer matching programs...

41 CFR 105-64.110 - When may GSA establish computer matching programs?

Code of Federal Regulations, 2014 CFR

2014-01-01

... computer matching programs? 105-64.110 Section 105-64.110 Public Contracts and Property Management Federal... GSA establish computer matching programs? (a) System managers will establish computer matching... direction of the GSA Data Integrity Board that will be established when and if computer matching programs...

41 CFR 105-64.110 - When may GSA establish computer matching programs?

Code of Federal Regulations, 2010 CFR

2010-07-01

... computer matching programs? 105-64.110 Section 105-64.110 Public Contracts and Property Management Federal... GSA establish computer matching programs? (a) System managers will establish computer matching... direction of the GSA Data Integrity Board that will be established when and if computer matching programs...

41 CFR 105-64.110 - When may GSA establish computer matching programs?

Code of Federal Regulations, 2011 CFR

2011-01-01

... computer matching programs? 105-64.110 Section 105-64.110 Public Contracts and Property Management Federal... GSA establish computer matching programs? (a) System managers will establish computer matching... direction of the GSA Data Integrity Board that will be established when and if computer matching programs...

Computer program user's manual for FIREFINDER digital topographic data verification library dubbing system

NASA Astrophysics Data System (ADS)

Ceres, M.; Heselton, L. R., III

1981-11-01

This manual describes the computer programs for the FIREFINDER Digital Topographic Data Verification-Library-Dubbing System (FFDTDVLDS), and will assist in the maintenance of these programs. The manual contains detailed flow diagrams and associated descriptions for each computer program routine and subroutine. Complete computer program listings are also included. This information should be used when changes are made in the computer programs. The operating system has been designed to minimize operator intervention.

AV Programs for Computer Know-How.

ERIC Educational Resources Information Center

Mandell, Phyllis Levy

1985-01-01

Lists 44 audiovisual programs (most released between 1983 and 1984) grouped in seven categories: computers in society, introduction to computers, computer operations, languages and programing, computer graphics, robotics, computer careers. Excerpts from "School Library Journal" reviews, price, and intended grade level are included. Names…

Guidelines for development of NASA (National Aeronautics and Space Administration) computer security training programs

NASA Technical Reports Server (NTRS)

Tompkins, F. G.

1983-01-01

The report presents guidance for the NASA Computer Security Program Manager and the NASA Center Computer Security Officials as they develop training requirements and implement computer security training programs. NASA audiences are categorized based on the computer security knowledge required to accomplish identified job functions. Training requirements, in terms of training subject areas, are presented for both computer security program management personnel and computer resource providers and users. Sources of computer security training are identified.

Computer programs: Operational and mathematical, a compilation

NASA Technical Reports Server (NTRS)

1973-01-01

Several computer programs which are available through the NASA Technology Utilization Program are outlined. Presented are: (1) Computer operational programs which can be applied to resolve procedural problems swiftly and accurately. (2) Mathematical applications for the resolution of problems encountered in numerous industries. Although the functions which these programs perform are not new and similar programs are available in many large computer center libraries, this collection may be of use to centers with limited systems libraries and for instructional purposes for new computer operators.

Computer Literacy Project. A General Orientation in Basic Computer Concepts and Applications.

ERIC Educational Resources Information Center

Murray, David R.

This paper proposes a two-part, basic computer literacy program for university faculty, staff, and students with no prior exposure to computers. The program described would introduce basic computer concepts and computing center service programs and resources; provide fundamental preparation for other computer courses; and orient faculty towards…

Information Security: Federal Guidance Needed to Address Control Issues With Implementing Cloud Computing

DTIC Science & Technology

2010-05-01

Figure 2: Cloud Computing Deployment Models 13 Figure 3: NIST Essential Characteristics 14 Figure 4: NASA Nebula Container 37...Access Computing Environment (RACE) program, the National Aeronautics and Space Administration’s (NASA) Nebula program, and the Department of...computing programs: the DOD’s RACE program; NASA’s Nebula program; and Department of Transportation’s CARS program, including lessons learned related

An analysis of the 70-meter antenna hydrostatic bearing by means of computer simulation

NASA Technical Reports Server (NTRS)

Bartos, R. D.

1993-01-01

Recently, the computer program 'A Computer Solution for Hydrostatic Bearings with Variable Film Thickness,' used to design the hydrostatic bearing of the 70-meter antennas, was modified to improve the accuracy with which the program predicts the film height profile and oil pressure distribution between the hydrostatic bearing pad and the runner. This article presents a description of the modified computer program, the theory upon which the computer program computations are based, computer simulation results, and a discussion of the computer simulation results.

Computer Programs for Library Operations; Results of a Survey Conducted Between Fall 1971 and Spring 1972.

ERIC Educational Resources Information Center

Liberman, Eva; And Others

Many library operations involving large data banks lend themselves readily to computer operation. In setting up library computer programs, in changing or expanding programs, cost in programming and time delays could be substantially reduced if the programmers had access to library computer programs being used by other libraries, providing similar…

32 CFR 701.125 - Computer matching program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 5 2012-07-01 2012-07-01 false Computer matching program. 701.125 Section 701... OF THE NAVY DOCUMENTS AFFECTING THE PUBLIC DON Privacy Program § 701.125 Computer matching program. The DPO has responsibility for coordinating the approval of DOD's participation in Computer Matching...

32 CFR 701.125 - Computer matching program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 5 2014-07-01 2014-07-01 false Computer matching program. 701.125 Section 701... OF THE NAVY DOCUMENTS AFFECTING THE PUBLIC DON Privacy Program § 701.125 Computer matching program. The DPO has responsibility for coordinating the approval of DOD's participation in Computer Matching...

32 CFR 701.125 - Computer matching program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 5 2013-07-01 2013-07-01 false Computer matching program. 701.125 Section 701... OF THE NAVY DOCUMENTS AFFECTING THE PUBLIC DON Privacy Program § 701.125 Computer matching program. The DPO has responsibility for coordinating the approval of DOD's participation in Computer Matching...

32 CFR 701.125 - Computer matching program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Computer matching program. 701.125 Section 701... OF THE NAVY DOCUMENTS AFFECTING THE PUBLIC DON Privacy Program § 701.125 Computer matching program. The DPO has responsibility for coordinating the approval of DOD's participation in Computer Matching...

32 CFR 701.125 - Computer matching program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 5 2011-07-01 2011-07-01 false Computer matching program. 701.125 Section 701... OF THE NAVY DOCUMENTS AFFECTING THE PUBLIC DON Privacy Program § 701.125 Computer matching program. The DPO has responsibility for coordinating the approval of DOD's participation in Computer Matching...

Gender differences in the use of computers, programming, and peer interactions in computer science classrooms

NASA Astrophysics Data System (ADS)

Stoilescu, Dorian; Egodawatte, Gunawardena

2010-12-01

Research shows that female and male students in undergraduate computer science programs view computer culture differently. Female students are interested more in the use of computers than in doing programming, whereas male students see computer science mainly as a programming activity. The overall purpose of our research was not to find new definitions for computer science culture but to see how male and female students see themselves involved in computer science practices, how they see computer science as a successful career, and what they like and dislike about current computer science practices. The study took place in a mid-sized university in Ontario. Sixteen students and two instructors were interviewed to get their views. We found that male and female views are different on computer use, programming, and the pattern of student interactions. Female and male students did not have any major issues in using computers. In computing programming, female students were not so involved in computing activities whereas male students were heavily involved. As for the opinions about successful computer science professionals, both female and male students emphasized hard working, detailed oriented approaches, and enjoying playing with computers. The myth of the geek as a typical profile of successful computer science students was not found to be true.

Computer program for the computation of total sediment discharge by the modified Einstein procedure

USGS Publications Warehouse

Stevens, H.H.

1985-01-01

Two versions of a computer program to compute total sediment discharge by the modified Einstein procedure are presented. The FORTRAN 77 language version is for use on the PRIME computer, and the BASIC language version is for use on most microcomputers. The program contains built-in limitations and input-output options that closely follow the original modified Einstein procedure. Program documentation and listings of both versions of the program are included. (USGS)

Programming the Navier-Stokes computer: An abstract machine model and a visual editor

NASA Technical Reports Server (NTRS)

Middleton, David; Crockett, Tom; Tomboulian, Sherry

1988-01-01

The Navier-Stokes computer is a parallel computer designed to solve Computational Fluid Dynamics problems. Each processor contains several floating point units which can be configured under program control to implement a vector pipeline with several inputs and outputs. Since the development of an effective compiler for this computer appears to be very difficult, machine level programming seems necessary and support tools for this process have been studied. These support tools are organized into a graphical program editor. A programming process is described by which appropriate computations may be efficiently implemented on the Navier-Stokes computer. The graphical editor would support this programming process, verifying various programmer choices for correctness and deducing values such as pipeline delays and network configurations. Step by step details are provided and demonstrated with two example programs.

Computer Electronics. Florida Vocational Program Guide.

ERIC Educational Resources Information Center

University of South Florida, Tampa. Dept. of Adult and Vocational Education.

This packet contains a program guide and Career Merit Achievement Plan (Career MAP) for the implementation of a computer electronics technology (computer service technician) program in Florida secondary and postsecondary schools. The program guide describes the program content and structure, provides a program description, lists job titles under…

Another Program For Generating Interactive Graphics

NASA Technical Reports Server (NTRS)

Costenbader, Jay; Moleski, Walt; Szczur, Martha; Howell, David; Engelberg, Norm; Li, Tin P.; Misra, Dharitri; Miller, Philip; Neve, Leif; Wolf, Karl;

Adolescents' Chunking of Computer Programs.

ERIC Educational Resources Information Center

Magliaro, Susan; Burton, John K.

To investigate what children learn during computer programming instruction, students attending a summer computer camp were asked to recall either single lines or chunks of computer programs from either coherent or scrambled programs. The 16 subjects, ages 12 to 17, were divided into three instructional groups: (1) beginners, who were taught to…

Advanced Certification Program for Computer Graphic Specialists. Final Performance Report.

ERIC Educational Resources Information Center

Parkland Coll., Champaign, IL.

A pioneer program in computer graphics was implemented at Parkland College (Illinois) to meet the demand for specialized technicians to visualize data generated on high performance computers. In summer 1989, 23 students were accepted into the pilot program. Courses included C programming, calculus and analytic geometry, computer graphics, and…

32 CFR 505.13 - Computer Matching Agreement Program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 3 2013-07-01 2013-07-01 false Computer Matching Agreement Program. 505.13... AUTHORITIES AND PUBLIC RELATIONS ARMY PRIVACY ACT PROGRAM § 505.13 Computer Matching Agreement Program. (a) General provisions. (1) Pursuant to the Privacy Act and this part, DA records may be subject to computer...

32 CFR 505.13 - Computer Matching Agreement Program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 3 2012-07-01 2009-07-01 true Computer Matching Agreement Program. 505.13... AUTHORITIES AND PUBLIC RELATIONS ARMY PRIVACY ACT PROGRAM § 505.13 Computer Matching Agreement Program. (a) General provisions. (1) Pursuant to the Privacy Act and this part, DA records may be subject to computer...

32 CFR 505.13 - Computer Matching Agreement Program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 3 2014-07-01 2014-07-01 false Computer Matching Agreement Program. 505.13... AUTHORITIES AND PUBLIC RELATIONS ARMY PRIVACY ACT PROGRAM § 505.13 Computer Matching Agreement Program. (a) General provisions. (1) Pursuant to the Privacy Act and this part, DA records may be subject to computer...

77 FR 13388 - Treasury Inspector General for Tax Administration; Privacy Act of 1974: Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-06

...: Computer Matching Program AGENCY: Treasury Inspector General for Tax Administration, Treasury. ACTION... Internal Revenue Service (IRS) concerning the conduct of TIGTA's computer matching program. DATES... INFORMATION: TIGTA's computer matching program assists in the detection and deterrence of fraud, waste, and...

78 FR 50146 - Privacy Act of 1974: Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-16

... DEPARTMENT OF VETERANS AFFAIRS Privacy Act of 1974: Computer Matching Program AGENCY: Department of Veterans Affairs. ACTION: Notice of Computer Match Program. SUMMARY: Pursuant to 5 U.S.C. 552a... to conduct a computer matching program with the Internal Revenue Service (IRS). Data from the...

76 FR 47299 - Privacy Act of 1974: Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-04

... DEPARTMENT OF VETERANS AFFAIRS Privacy Act of 1974: Computer Matching Program AGENCY: Department of Veterans Affairs. ACTION: Notice of Computer Match Program. SUMMARY: Pursuant to 5 U.S.C. 552a... to conduct a computer matching program with the Internal Revenue Service (IRS). Data from the...

32 CFR 505.13 - Computer Matching Agreement Program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 3 2011-07-01 2009-07-01 true Computer Matching Agreement Program. 505.13... AUTHORITIES AND PUBLIC RELATIONS ARMY PRIVACY ACT PROGRAM § 505.13 Computer Matching Agreement Program. (a) General provisions. (1) Pursuant to the Privacy Act and this part, DA records may be subject to computer...

32 CFR 310.53 - Computer matching agreements (CMAs).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 2 2013-07-01 2013-07-01 false Computer matching agreements (CMAs). 310.53... (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.53 Computer.... (3) Justification and expected results. Explain why computer matching as opposed to some other...

32 CFR 310.53 - Computer matching agreements (CMAs).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 2 2014-07-01 2014-07-01 false Computer matching agreements (CMAs). 310.53... (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.53 Computer.... (3) Justification and expected results. Explain why computer matching as opposed to some other...

32 CFR 310.53 - Computer matching agreements (CMAs).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 2 2012-07-01 2012-07-01 false Computer matching agreements (CMAs). 310.53... (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.53 Computer.... (3) Justification and expected results. Explain why computer matching as opposed to some other...

32 CFR 310.53 - Computer matching agreements (CMAs).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false Computer matching agreements (CMAs). 310.53... (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.53 Computer.... (3) Justification and expected results. Explain why computer matching as opposed to some other...

32 CFR 310.53 - Computer matching agreements (CMAs).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 2 2011-07-01 2011-07-01 false Computer matching agreements (CMAs). 310.53... (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.53 Computer.... (3) Justification and expected results. Explain why computer matching as opposed to some other...

Computer programs for computing particle-size statistics of fluvial sediments

USGS Publications Warehouse

Stevens, H.H.; Hubbell, D.W.

1986-01-01

Two versions of computer programs for inputing data and computing particle-size statistics of fluvial sediments are presented. The FORTRAN 77 language versions are for use on the Prime computer, and the BASIC language versions are for use on microcomputers. The size-statistics program compute Inman, Trask , and Folk statistical parameters from phi values and sizes determined for 10 specified percent-finer values from inputed size and percent-finer data. The program also determines the percentage gravel, sand, silt, and clay, and the Meyer-Peter effective diameter. Documentation and listings for both versions of the programs are included. (Author 's abstract)

NEMAR plotting computer program

NASA Technical Reports Server (NTRS)

Myler, T. R.

1981-01-01

A FORTRAN coded computer program which generates CalComp plots of trajectory parameters is examined. The trajectory parameters are calculated and placed on a data file by the Near Earth Mission Analysis Routine computer program. The plot program accesses the data file and generates the plots as defined by inputs to the plot program. Program theory, user instructions, output definitions, subroutine descriptions and detailed FORTRAN coding information are included. Although this plot program utilizes a random access data file, a data file of the same type and formatted in 102 numbers per record could be generated by any computer program and used by this plot program.

User's guide to the NOZL3D and NOZLIC computer programs

NASA Technical Reports Server (NTRS)

Thomas, P. D.

1980-01-01

Complete FORTRAN listings and running instructions are given for a set of computer programs that perform an implicit numerical solution to the unsteady Navier-Stokes equations to predict the flow characteristics and performance of nonaxisymmetric nozzles. The set includes the NOZL3D program, which performs the flow computations; the NOZLIC program, which sets up the flow field initial conditions for general nozzle configurations, and also generates the computational grid for simple two dimensional and axisymmetric configurations; and the RGRIDD program, which generates the computational grid for complicated three dimensional configurations. The programs are designed specifically for the NASA-Langley CYBER 175 computer, and employ auxiliary disk files for primary data storage. Input instructions and computed results are given for four test cases that include two dimensional, three dimensional, and axisymmetric configurations.

OASIS connections: results from an evaluation study.

PubMed

Czaja, Sara J; Lee, Chin Chin; Branham, Janice; Remis, Peggy

2012-10-01

The objectives of this study were to evaluate a community-based basic computer and Internet training program designed for older adults, provide recommendations for program refinement, and gather preliminary information on program sustainability. The program was developed by the OASIS Institute, a nonprofit agency serving older adults and implemented in 4 cities by community trainers across the United States. One hundred and ninety-six adults aged 40-90 years were assigned to the training or a wait-list control group. Knowledge of computers and the Internet, attitudes toward computers, and computer/Internet use were assessed at baseline, posttraining, and 3 months posttraining. The program was successful in increasing the computer/Internet skills of the trainees. The data indicated a significant increase in computer and Internet knowledge and comfort with computers among those who received the training. Further, those who completed the course reported an increase in both computer and Internet use 3 months posttraining. The findings indicate that a community-based computer and Internet training program delivered by community instructors can be effective in terms of increasing computer and Internet skills and comfort with computer technology among older adults.

Introducing Hospital Staff to Computer Concepts: An Educational Program

PubMed Central

Kaplan, Bonnie

1981-01-01

An in-house computer education program for hospital staff ran for two years at a large, metropolitan hospital. The program drew physicians, administrators, department heads, secretaries, technicians, and data managers to courses, seminars, and workshops on medical computing. Two courses, an introduction to computer concepts and a programming course, are described and evaluated.

78 FR 29748 - Privacy Act of 1974; Computer Matching Program Between the Department of Education and the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-21

... DEPARTMENT OF EDUCATION Privacy Act of 1974; Computer Matching Program Between the Department of... document provides notice of the continuation of a computer matching program between the Department of... 5301, the Department of Justice and the Department of Education implemented a computer matching program...

75 FR 53005 - Privacy Act of 1974, as amended; Notice of Computer Matching Program (Railroad Retirement Board...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-30

... notice of its renewal of an ongoing computer-matching program with the Social Security Administration... computer-matching program with the Committee on Homeland Security and Governmental Affairs of the Senate... RAILROAD RETIREMENT BOARD Privacy Act of 1974, as amended; Notice of Computer Matching Program...

78 FR 34678 - Privacy Act of 1974, as Amended; Notice of Computer Matching Program (Railroad Retirement Board...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

... notice of its renewal of an ongoing computer-matching program with the Social Security Administration... computer-matching program with the Committee on Homeland Security and Governmental Affairs of the Senate... RAILROAD RETIREMENT BOARD Privacy Act of 1974, as Amended; Notice of Computer Matching Program...

75 FR 8311 - Privacy Act of 1974; Notice of a Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-24

...; Notice of a Computer Matching Program AGENCY: Defense Manpower Data Center, DoD. ACTION: Notice of a... hereby giving notice to the record subjects of a computer matching program between the Department of... conduct a computer matching program between the agencies. The purpose of this agreement is to verify an...

76 FR 50198 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-12

... DEPARTMENT OF EDUCATION Privacy Act of 1974; Computer Matching Program AGENCY: Office of the Inspector General, U.S. Department of Education. ACTION: Notice of computer matching between the U.S... conduct of computer matching programs, notice is hereby given of the establishment of a computer matching...

Use of CYBER 203 and CYBER 205 computers for three-dimensional transonic flow calculations

NASA Technical Reports Server (NTRS)

Melson, N. D.; Keller, J. D.

1983-01-01

Experiences are discussed for modifying two three-dimensional transonic flow computer programs (FLO 22 and FLO 27) for use on the CDC CYBER 203 computer system. Both programs were originally written for use on serial machines. Several methods were attempted to optimize the execution of the two programs on the vector machine: leaving the program in a scalar form (i.e., serial computation) with compiler software used to optimize and vectorize the program, vectorizing parts of the existing algorithm in the program, and incorporating a vectorizable algorithm (ZEBRA I or ZEBRA II) in the program. Comparison runs of the programs were made on CDC CYBER 175. CYBER 203, and two pipe CDC CYBER 205 computer systems.

A Microcomputer-Based Computer Science Program.

ERIC Educational Resources Information Center

Compeau, Larry D.

1984-01-01

Examines the use of the microcomputer in computer science programs as an alternative to time-sharing computers at North Country Community College. Discusses factors contributing to the program's success, security problems, outside application possibilities, and program implementation concerns. (DMM)

NASA's computer science research program

NASA Technical Reports Server (NTRS)

Larsen, R. L.

1983-01-01

Following a major assessment of NASA's computing technology needs, a new program of computer science research has been initiated by the Agency. The program includes work in concurrent processing, management of large scale scientific databases, software engineering, reliable computing, and artificial intelligence. The program is driven by applications requirements in computational fluid dynamics, image processing, sensor data management, real-time mission control and autonomous systems. It consists of university research, in-house NASA research, and NASA's Research Institute for Advanced Computer Science (RIACS) and Institute for Computer Applications in Science and Engineering (ICASE). The overall goal is to provide the technical foundation within NASA to exploit advancing computing technology in aerospace applications.

Identification of Cognitive Processes of Effective and Ineffective Students during Computer Programming

ERIC Educational Resources Information Center

Renumol, V. G.; Janakiram, Dharanipragada; Jayaprakash, S.

2010-01-01

Identifying the set of cognitive processes (CPs) a student can go through during computer programming is an interesting research problem. It can provide a better understanding of the human aspects in computer programming process and can also contribute to the computer programming education in general. The study identified the presence of a set of…

A Program To Develop through LOGO the Computer Self-Confidence of Seventh Grade Low-Achieving Girls.

ERIC Educational Resources Information Center

Angell, Marion D.

This practicum report describes the development of a program designed to improve self-confidence in low-achieving seventh grade girls towards computers. The questionnaire "My Feelings Towards Computers" was used for pre- and post-comparisons. Students were introduced to the computer program LOGO, were taught to compose programs using the…

Advanced Computer Aids in the Planning and Execution of Air Warfare and Ground Strike Operations: Conference Proceedings, Meeting of the Avionics Panels of AGARD (51st) Held in Kongsberg, Norway on 12-16 May 1986

DTIC Science & Technology

1986-02-01

the area of Artificial Intelligence (At). DARPA’s Strategic Computing Program 13 developing an At ýtchnology base upon which several applications...technologies with the Strategic Computing Program . In late 1983 the Strategic Computing Program (SCP) wes announced. The program was organizsd to develop...solving a resource allocation problem. The remainder of this paper will discuss the TEMPLAR progeam as it relates to the Strategic Computing Program

Use of a Computer Language in Teaching Dynamic Programming. Final Report.

ERIC Educational Resources Information Center

Trimble, C. J.; And Others

Most optimization problems of any degree of complexity must be solved using a computer. In the teaching of dynamic programing courses, it is often desirable to use a computer in problem solution. The solution process involves conceptual formulation and computational Solution. Generalized computer codes for dynamic programing problem solution…

A Computer Program for Crystal Drawing.

ERIC Educational Resources Information Center

Dutch, Steven I.

1981-01-01

Described is a computer program which accepts face data, performs all necessary symmetry operations, and produces a drawing of the resulting crystal. The program shortens computing time to make it suitable for online teaching use or for use in small computers. (Author/DC)

Programming Support Library (PSL). Users Manual.

DTIC Science & Technology

1978-05-01

which provides the tools to organize, implement, and control computer program develop- ment. This involves the support of the actual programming process...provides the tools toorganize, implement, and control computer program development. The system is designed specifically to support top-down development...Structured Programming are finding increasing application in the computing community. Structured programs are, however, difficult to write in

Enhancing Digital Fluency through a Training Program for Creative Problem Solving Using Computer Programming

ERIC Educational Resources Information Center

Kim, SugHee; Chung, KwangSik; Yu, HeonChang

2013-01-01

The purpose of this paper is to propose a training program for creative problem solving based on computer programming. The proposed program will encourage students to solve real-life problems through a creative thinking spiral related to cognitive skills with computer programming. With the goal of enhancing digital fluency through this proposed…

Introduction to the Atari Computer. A Program Written in the Pilot Programming Language.

ERIC Educational Resources Information Center

Schlenker, Richard M.

Designed to be an introduction to the Atari microcomputers for beginners, the interactive computer program listed in this document is written in the Pilot programing language. Instructions are given for entering and storing the program in the computer memory for use by students. (MES)

Computer Science 205. Interim Guide, 1983.

ERIC Educational Resources Information Center

Manitoba Dept. of Education, Winnipeg.

This guide to a 4-unit, required high school computer science course emphasizes problem solving and computer programming and is designed for use with a variety of hardware configurations and programming languages. An overview covers the program rationale, goals and objectives, program design and description, program implementation, time allotment,…

40 CFR Appendix C to Part 67 - Computer Program

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 16 2013-07-01 2013-07-01 false Computer Program C Appendix C to Part 67 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) EPA APPROVAL OF STATE NONCOMPLIANCE PENALTY PROGRAM Pt. 67, App. C Appendix C to Part 67—Computer Program Note...

40 CFR Appendix C to Part 67 - Computer Program

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 16 2014-07-01 2014-07-01 false Computer Program C Appendix C to Part 67 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) EPA APPROVAL OF STATE NONCOMPLIANCE PENALTY PROGRAM Pt. 67, App. C Appendix C to Part 67—Computer Program Note...

40 CFR Appendix C to Part 67 - Computer Program

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 16 2012-07-01 2012-07-01 false Computer Program C Appendix C to Part 67 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) EPA APPROVAL OF STATE NONCOMPLIANCE PENALTY PROGRAM Pt. 67, App. C Appendix C to Part 67—Computer Program Note...

40 CFR Appendix C to Part 67 - Computer Program

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Computer Program C Appendix C to Part 67 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) EPA APPROVAL OF STATE NONCOMPLIANCE PENALTY PROGRAM Pt. 67, App. C Appendix C to Part 67—Computer Program Note...

Low-Budget Computer Programming in Your School (An Alternative to the Cost of Large Computers). Illinois Series on Educational Applications of Computers. No. 14.

ERIC Educational Resources Information Center

Dennis, J. Richard; Thomson, David

This paper is concerned with a low cost alternative for providing computer experience to secondary school students. The brief discussion covers the programmable calculator and its relevance for teaching the concepts and the rudiments of computer programming and for computer problem solving. A list of twenty-five programming activities related to…

Simulation of the stress computation in shells

NASA Technical Reports Server (NTRS)

Salama, M.; Utku, S.

1978-01-01

A self-teaching computer program is described, whereby the stresses in thin shells can be computed with good accuracy using the best fit approach. The program is designed for use in interactive game mode to allow the structural engineer to learn about (1) the major sources of difficulties and associated errors in the computation of stresses in thin shells, (2) possible ways to reduce the errors, and (3) trade-off between computational cost and accuracy. Included are derivation of the computational approach, program description, and several examples illustrating the program usage.

A modular finite-element model (MODFE) for areal and axisymmetric ground-water-flow problems, Part 3: Design philosophy and programming details

USGS Publications Warehouse

Torak, L.J.

1993-01-01

A MODular Finite-Element, digital-computer program (MODFE) was developed to simulate steady or unsteady-state, two-dimensional or axisymmetric ground-water-flow. The modular structure of MODFE places the computationally independent tasks that are performed routinely by digital-computer programs simulating ground-water flow into separate subroutines, which are executed from the main program by control statements. Each subroutine consists of complete sets of computations, or modules, which are identified by comment statements, and can be modified by the user without affecting unrelated computations elsewhere in the program. Simulation capabilities can be added or modified by either adding or modifying subroutines that perform specific computational tasks, and the modular-program structure allows the user to create versions of MODFE that contain only the simulation capabilities that pertain to the ground-water problem of interest. MODFE is written in a Fortran programming language that makes it virtually device independent and compatible with desk-top personal computers and large mainframes. MODFE uses computer storage and execution time efficiently by taking advantage of symmetry and sparseness within the coefficient matrices of the finite-element equations. Parts of the matrix coefficients are computed and stored as single-subscripted variables, which are assembled into a complete coefficient just prior to solution. Computer storage is reused during simulation to decrease storage requirements. Descriptions of subroutines that execute the computational steps of the modular-program structure are given in tables that cross reference the subroutines with particular versions of MODFE. Programming details of linear and nonlinear hydrologic terms are provided. Structure diagrams for the main programs show the order in which subroutines are executed for each version and illustrate some of the linear and nonlinear versions of MODFE that are possible. Computational aspects of changing stresses and boundary conditions with time and of mass-balance and error terms are given for each hydrologic feature. Program variables are listed and defined according to their occurrence in the main programs and in subroutines. Listings of the main programs and subroutines are given.

Designing and Creating Computer-Assisted Instruction.

ERIC Educational Resources Information Center

McMeen, George R.

Designed to encourage the use of a defined methodology and careful planning in creating computer-assisted instructional programs, this paper describes the instructional design process, compares computer-assisted instruction (CAI) and programmed instruction (PI), and discusses pragmatic concerns in computer programming. Topics addressed include:…

Program For Generating Interactive Displays

NASA Technical Reports Server (NTRS)

Costenbader, Jay; Moleski, Walt; Szczur, Martha; Howell, David; Engelberg, Norm; Li, Tin P.; Misra, Dharitri; Miller, Philip; Neve, Leif; Wolf, Karl;

Generating and executing programs for a floating point single instruction multiple data instruction set architecture

DOEpatents

Gschwind, Michael K

2013-04-16

Mechanisms for generating and executing programs for a floating point (FP) only single instruction multiple data (SIMD) instruction set architecture (ISA) are provided. A computer program product comprising a computer recordable medium having a computer readable program recorded thereon is provided. The computer readable program, when executed on a computing device, causes the computing device to receive one or more instructions and execute the one or more instructions using logic in an execution unit of the computing device. The logic implements a floating point (FP) only single instruction multiple data (SIMD) instruction set architecture (ISA), based on data stored in a vector register file of the computing device. The vector register file is configured to store both scalar and floating point values as vectors having a plurality of vector elements.

Causal Attributions of Success and Failure Made by Undergraduate Students in an Introductory-Level Computer Programming Course

ERIC Educational Resources Information Center

Hawi, N.

2010-01-01

The purpose of this research is to identify the causal attributions of business computing students in an introductory computer programming course, in the computer science department at Notre Dame University, Louaize. Forty-five male and female undergraduates who completed the computer programming course that extended for a 13-week semester…

SuperPILOT: A Comprehensive Computer-Assisted Instruction Programming Language for the Apple II Computer.

ERIC Educational Resources Information Center

Falleur, David M.

This presentation describes SuperPILOT, an extended version of Apple PILOT, a programming language for developing computer-assisted instruction (CAI) with the Apple II computer that includes the features of its early PILOT (Programmed Inquiry, Learning or Teaching) ancestors together with new features that make use of the Apple computer's advanced…

DORMAN computer program (study 2.5). Volume 2: User's guide and programmer's guide. [development of data bank for computerized information storage of NASA programs

NASA Technical Reports Server (NTRS)

Wray, S. T., Jr.

1973-01-01

The DORMAN program was developed to create and modify a data bank containing data decks which serve as input to the DORCA Computer Program. Via a remote terminal a user can access the bank, extract any data deck, modify that deck, output the modified deck to be input to the DORCA program, and save the modified deck in the data bank. This computer program is an assist in the utilization of the DORCA program. The program is dimensionless and operates almost entirely in integer mode. The program was developed on the CDC 6400/7600 complex for implementation on a UNIVAC 1108 computer.

Computer programs for thermodynamic and transport properties of hydrogen

NASA Technical Reports Server (NTRS)

Hall, W. J.; Mc Carty, R. D.; Roder, H. M.

1968-01-01

Computer program subroutines provide the thermodynamic and transport properties of hydrogen in tabular form. The programs provide 18 combinations of input and output variables. This program is written in FORTRAN 4 for use on the IBM 7044 or CDC 3600 computers.

The Compubus Evaluation.

ERIC Educational Resources Information Center

Klimko, Ivan P.

The Computer Bus Program (Compubus Program) of the Modesto City Schools (California) was evaluated to determine the effectiveness of the computer literacy program for fourth, fifth, and sixth grade students at eight elementary compensatory education schools. The program provided instruction on computer vocabulary, knowledge, and applications in a…

Technique to eliminate computational instability in multibody simulations employing the Lagrange multiplier

NASA Technical Reports Server (NTRS)

Watts, G.

1992-01-01

A programming technique to eliminate computational instability in multibody simulations that use the Lagrange multiplier is presented. The computational instability occurs when the attached bodies drift apart and violate the constraints. The programming technique uses the constraint equation, instead of integration, to determine the coordinates that are not independent. Although the equations of motion are unchanged, a complete derivation of the incorporation of the Lagrange multiplier into the equation of motion for two bodies is presented. A listing of a digital computer program which uses the programming technique to eliminate computational instability is also presented. The computer program simulates a solid rocket booster and parachute connected by a frictionless swivel.

ICASE Computer Science Program

NASA Technical Reports Server (NTRS)

1985-01-01

The Institute for Computer Applications in Science and Engineering computer science program is discussed in outline form. Information is given on such topics as problem decomposition, algorithm development, programming languages, and parallel architectures.

Human operator identification model and related computer programs

NASA Technical Reports Server (NTRS)

Kessler, K. M.; Mohr, J. N.

1978-01-01

Four computer programs which provide computational assistance in the analysis of man/machine systems are reported. The programs are: (1) Modified Transfer Function Program (TF); (2) Time Varying Response Program (TVSR); (3) Optimal Simulation Program (TVOPT); and (4) Linear Identification Program (SCIDNT). The TV program converts the time domain state variable system representative to frequency domain transfer function system representation. The TVSR program computes time histories of the input/output responses of the human operator model. The TVOPT program is an optimal simulation program and is similar to TVSR in that it produces time histories of system states associated with an operator in the loop system. The differences between the two programs are presented. The SCIDNT program is an open loop identification code which operates on the simulated data from TVOPT (or TVSR) or real operator data from motion simulators.

32 CFR 310.52 - Computer matching publication and review requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 2 2012-07-01 2012-07-01 false Computer matching publication and review... OF DEFENSE (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.52 Computer matching publication and review requirements. (a) DoD Components shall identify the...

32 CFR 310.52 - Computer matching publication and review requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 2 2014-07-01 2014-07-01 false Computer matching publication and review... OF DEFENSE (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.52 Computer matching publication and review requirements. (a) DoD Components shall identify the...

32 CFR 310.52 - Computer matching publication and review requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 2 2013-07-01 2013-07-01 false Computer matching publication and review... OF DEFENSE (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.52 Computer matching publication and review requirements. (a) DoD Components shall identify the...

32 CFR 310.52 - Computer matching publication and review requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false Computer matching publication and review... OF DEFENSE (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.52 Computer matching publication and review requirements. (a) DoD Components shall identify the...

32 CFR 310.52 - Computer matching publication and review requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 2 2011-07-01 2011-07-01 false Computer matching publication and review... OF DEFENSE (CONTINUED) PRIVACY PROGRAM DOD PRIVACY PROGRAM Computer Matching Program Procedures § 310.52 Computer matching publication and review requirements. (a) DoD Components shall identify the...

Program Aids Specification Of Multiple-Block Grids

NASA Technical Reports Server (NTRS)

Sorenson, R. L.; Mccann, K. M.

1993-01-01

3DPREP computer program aids specification of multiple-block computational grids. Highly interactive graphical preprocessing program designed for use on powerful graphical scientific computer workstation. Divided into three main parts, each corresponding to principal graphical-and-alphanumerical display. Relieves user of some burden of collecting and formatting many data needed to specify blocks and grids, and prepares input data for NASA's 3DGRAPE grid-generating computer program.

Data Processing: Fifteen Suggestions for Computer Training in Your Business Education Classes.

ERIC Educational Resources Information Center

Barr, Lowell L.

1980-01-01

Presents 15 suggestions for training business education students in the use of computers. Suggestions involve computer language, method of presentation, laboratory time, programing assignments, instructions and handouts, problem solving, deadlines, reviews, programming concepts, programming logic, documentation, and defensive programming. (CT)

78 FR 15730 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-12

... 1974; Computer Matching Program AGENCY: U.S. Citizenship and Immigration Services, Department of... Matching Program between the Department of Homeland Security, U.S. Citizenship and Immigration Services and... computer matching program between the Department of Homeland Security, U.S. Citizenship and Immigration...

High performance computing and communications program

NASA Technical Reports Server (NTRS)

Holcomb, Lee

1992-01-01

A review of the High Performance Computing and Communications (HPCC) program is provided in vugraph format. The goals and objectives of this federal program are as follows: extend U.S. leadership in high performance computing and computer communications; disseminate the technologies to speed innovation and to serve national goals; and spur gains in industrial competitiveness by making high performance computing integral to design and production.

Algorithms for computations of Loday algebras' invariants

NASA Astrophysics Data System (ADS)

Hussain, Sharifah Kartini Said; Rakhimov, I. S.; Basri, W.

2017-04-01

The paper is devoted to applications of some computer programs to study structural determination of Loday algebras. We present how these computer programs can be applied in computations of various invariants of Loday algebras and provide several computer programs in Maple to verify Loday algebras' identities, the isomorphisms between the algebras, as a special case, to describe the automorphism groups, centroids and derivations.

The Effects of a Robot Game Environment on Computer Programming Education for Elementary School Students

ERIC Educational Resources Information Center

Shim, Jaekwoun; Kwon, Daiyoung; Lee, Wongyu

2017-01-01

In the past, computer programming was perceived as a task only carried out by computer scientists; in the 21st century, however, computer programming is viewed as a critical and necessary skill that everyone should learn. In order to improve teaching of problem-solving abilities in a computing environment, extensive research is being done on…

Processing Device for High-Speed Execution of an Xrisc Computer Program

NASA Technical Reports Server (NTRS)

Ng, Tak-Kwong (Inventor); Mills, Carl S. (Inventor)

2016-01-01

A processing device for high-speed execution of a computer program is provided. A memory module may store one or more computer programs. A sequencer may select one of the computer programs and controls execution of the selected program. A register module may store intermediate values associated with a current calculation set, a set of output values associated with a previous calculation set, and a set of input values associated with a subsequent calculation set. An external interface may receive the set of input values from a computing device and provides the set of output values to the computing device. A computation interface may provide a set of operands for computation during processing of the current calculation set. The set of input values are loaded into the register and the set of output values are unloaded from the register in parallel with processing of the current calculation set.

Some Programs Should Not Run on Laptops - Providing Programmatic Access to Applications Via Web Services

NASA Astrophysics Data System (ADS)

Gupta, V.; Gupta, N.; Gupta, S.; Field, E.; Maechling, P.

2003-12-01

Modern laptop computers, and personal computers, can provide capabilities that are, in many ways, comparable to workstations or departmental servers. However, this doesn't mean we should run all computations on our local computers. We have identified several situations in which it preferable to implement our seismological application programs in a distributed, server-based, computing model. In this model, application programs on the user's laptop, or local computer, invoke programs that run on an organizational server, and the results are returned to the invoking system. Situations in which a server-based architecture may be preferred include: (a) a program is written in a language, or written for an operating environment, that is unsupported on the local computer, (b) software libraries or utilities required to execute a program are not available on the users computer, (c) a computational program is physically too large, or computationally too expensive, to run on a users computer, (d) a user community wants to enforce a consistent method of performing a computation by standardizing on a single implementation of a program, and (e) the computational program may require current information, that is not available to all client computers. Until recently, distributed, server-based, computational capabilities were implemented using client/server architectures. In these architectures, client programs were often written in the same language, and they executed in the same computing environment, as the servers. Recently, a new distributed computational model, called Web Services, has been developed. Web Services are based on Internet standards such as XML, SOAP, WDSL, and UDDI. Web Services offer the promise of platform, and language, independent distributed computing. To investigate this new computational model, and to provide useful services to the SCEC Community, we have implemented several computational and utility programs using a Web Service architecture. We have hosted these Web Services as a part of the SCEC Community Modeling Environment (SCEC/CME) ITR Project (http://www.scec.org/cme). We have implemented Web Services for several of the reasons sited previously. For example, we implemented a FORTRAN-based Earthquake Rupture Forecast (ERF) as a Web Service for use by client computers that don't support a FORTRAN runtime environment. We implemented a Generic Mapping Tool (GMT) Web Service for use by systems that don't have local access to GMT. We implemented a Hazard Map Calculator Web Service to execute Hazard calculations that are too computationally intensive to run on a local system. We implemented a Coordinate Conversion Web Service to enforce a standard and consistent method for converting between UTM and Lat/Lon. Our experience developing these services indicates both strengths and weakness in current Web Service technology. Client programs that utilize Web Services typically need network access, a significant disadvantage at times. Programs with simple input and output parameters were the easiest to implement as Web Services, while programs with complex parameter-types required a significant amount of additional development. We also noted that Web services are very data-oriented, and adapting object-oriented software into the Web Service model proved problematic. Also, the Web Service approach of converting data types into XML format for network transmission has significant inefficiencies for some data sets.

Structured Problem Solving and the Basic Graphic Methods within a Total Quality Leadership Setting: Case Study

DTIC Science & Technology

1992-02-01

develop,, and maintains computer programs for the Department of the Navy. It provides life cycle support for over 50 computer programs installed at over...the computer programs . Table 4 presents a list of possible product or output measures of functionality for ACDS Block 0 programs . Examples of output...were identified as important "causes" of process performance. Functionality of the computer programs was the result or "effect" of the combination of

Space shuttle solid rocket booster recovery system definition. Volume 3: SRB water impact loads computer program, user's manual

NASA Technical Reports Server (NTRS)

1973-01-01

This user's manual describes the FORTRAN IV computer program developed to compute the total vertical load, normal concentrated pressure loads, and the center of pressure of typical SRB water impact slapdown pressure distributions specified in the baseline configuration. The program prepares the concentrated pressure load information in punched card format suitable for input to the STAGS computer program. In addition, the program prepares for STAGS input the inertia reacting loads to the slapdown pressure distributions.

Computer programs for forward and inverse modeling of acoustic and electromagnetic data

USGS Publications Warehouse

Ellefsen, Karl J.

2011-01-01

A suite of computer programs was developed by U.S. Geological Survey personnel for forward and inverse modeling of acoustic and electromagnetic data. This report describes the computer resources that are needed to execute the programs, the installation of the programs, the program designs, some tests of their accuracy, and some suggested improvements.

Scratch: Multimedia Programming Environment for Young Gifted Learners

ERIC Educational Resources Information Center

Lee, Young-Jin

2011-01-01

Despite the educational benefits, computer programming has not been adopted in the current K-12 education as much as it could have been. One of the reasons for the low adoption of computer programming in K-12 education is the time it takes for (especially young) students to learn computer programming using a text-based programming language, which…

Enhancing programming logic thinking using analogy mapping

NASA Astrophysics Data System (ADS)

Sukamto, R. A.; Megasari, R.

2018-05-01

Programming logic thinking is the most important competence for computer science students. However, programming is one of the difficult subject in computer science program. This paper reports our work about enhancing students' programming logic thinking using Analogy Mapping for basic programming subject. Analogy Mapping is a computer application which converts source code into analogies images. This research used time series evaluation and the result showed that Analogy Mapping can enhance students' programming logic thinking.

Software Reviews. Programs Worth a Second Look.

ERIC Educational Resources Information Center

Schneider, Roxanne; Eiser, Leslie

1989-01-01

Reviewed are three computer software packages for use in middle/high school classrooms. Included are "MacWrite II," a word-processing program for MacIntosh computers; "Super Story Tree," a word-processing program for Apple and IBM computers; and "Math Blaster Mystery," for IBM, Apple, and Tandy computers. (CW)

An Interactive Computer-Based Training Program for Beginner Personal Computer Maintenance.

ERIC Educational Resources Information Center

Summers, Valerie Brooke

A computer-assisted instructional program, which was developed for teaching beginning computer maintenance to employees of Unisys, covered external hardware maintenance, proper diskette care, making software backups, and electro-static discharge prevention. The procedure used in developing the program was based upon the Dick and Carey (1985) model…

A Review of Models for Teacher Preparation Programs for Precollege Computer Science Education.

ERIC Educational Resources Information Center

Deek, Fadi P.; Kimmel, Howard

2002-01-01

Discusses the need for adequate precollege computer science education and focuses on the issues of teacher preparation programs and requirements needed to teach high school computer science. Presents models of teacher preparation programs and compares state requirements with Association for Computing Machinery (ACM) recommendations. (Author/LRW)

DYNALIST II : A Computer Program for Stability and Dynamic Response Analysis of Rail Vehicle Systems : Volume 2. User's Manual.

DOT National Transportation Integrated Search

1975-02-01

A methodology and a computer program, DYNALIST II, have been developed for computing the response of rail vehicle systems to sinusoidal or stationary random rail irregularities. The computer program represents an extension of the earlier DYNALIST pro...

78 FR 45513 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-29

...; Computer Matching Program AGENCY: Defense Manpower Data Center (DMDC), DoD. ACTION: Notice of a Computer... individual's privacy, and would result in additional delay in determining eligibility and, if applicable, the... Defense. NOTICE OF A COMPUTER MATCHING PROGRAM AMONG THE DEFENSE MANPOWER DATA CENTER, THE DEPARTMENT OF...

76 FR 1410 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-10

...; Computer Matching Program AGENCY: Defense Manpower Data Center (DMDC), DoD. ACTION: Notice of a Computer... administrative burden, constitute a greater intrusion of the individual's privacy, and would result in additional... Liaison Officer, Department of Defense. Notice of a Computer Matching Program Among the Defense Manpower...

DYNALIST II : A Computer Program for Stability and Dynamic Response Analysis of Rail Vehicle Systems : Volume 1. Technical Report.

DOT National Transportation Integrated Search

1975-02-01

A methodology and a computer program, DYNALIST II, have been developed for computing the response of rail vehicle systems to sinusoidal or stationary random rail irregularities. The computer program represents an extension of the earlier DYNALIST pro...

A Research Program in Computer Technology. 1986 Annual Technical Report

DTIC Science & Technology

1989-08-01

1986 (Annual Technical Report I July 1985 - June 1986 A Research Program in Computer Technology ISI/SR-87-178 U S C INFORMA-TION S C I EN C ES...Program in Computer Technology (Unclassified) 12. PERSONAL AUTHOR(S) 151 Research Staff 13a. TYPE OF REPORT 113b. TIME COVERED 14 DATE OF REPORT (Yeer...survivable networks 17. distributed processing, local networks, personal computers, workstation environment 18. computer acquisition, Strategic Computing 19

FORTRAN manpower account program

NASA Technical Reports Server (NTRS)

Strand, J. N.

1972-01-01

Computer program for determining manpower costs for full time, part time, and contractor personnel is discussed. Twelve different tables resulting from computer output are described. Program is written in FORTRAN 4 for IBM 360/65 computer.

Graphics and composite material computer program enhancements for SPAR

NASA Technical Reports Server (NTRS)

Farley, G. L.; Baker, D. J.

1980-01-01

User documentation is provided for additional computer programs developed for use in conjunction with SPAR. These programs plot digital data, simplify input for composite material section properties, and compute lamina stresses and strains. Sample problems are presented including execution procedures, program input, and graphical output.

Design and performance analysis of solid-propellant rocket motors using a simplified computer program

NASA Technical Reports Server (NTRS)

Sforzini, R. H.

1972-01-01

An analysis and a computer program are presented which represent a compromise between the more sophisticated programs using precise burning geometric relations and the textbook type of solutions. The program requires approximately 900 computer cards including a set of 20 input data cards required for a typical problem. The computer operating time for a single configuration is approximately 1 minute and 30 seconds on the IBM 360 computer. About l minute and l5 seconds of the time is compilation time so that additional configurations input at the same time require approximately 15 seconds each. The program uses approximately 11,000 words on the IBM 360. The program is written in FORTRAN 4 and is readily adaptable for use on a number of different computers: IBM 7044, IBM 7094, and Univac 1108.

Improved sonic-box computer program for calculating transonic aerodynamic loads on oscillating wings with thickness

NASA Technical Reports Server (NTRS)

Ruo, S. Y.

1978-01-01

A computer program was developed to account approximately for the effects of finite wing thickness in transonic potential flow over an oscillation wing of finite span. The program is based on the original sonic box computer program for planar wing which was extended to account for the effect of wing thickness. Computational efficiency and accuracy were improved and swept trailing edges were accounted for. Account for the nonuniform flow caused by finite thickness was made by application of the local linearization concept with appropriate coordinate transformation. A brief description of each computer routine and the applications of cubic spline and spline surface data fitting techniques used in the program are given, and the method of input was shown in detail. Sample calculations as well as a complete listing of the computer program listing are presented.

Numerical nonlinear inelastic analysis of stiffened shells of revolution. Volume 3: Engineer's program manual for STARS-2P digital computer program

NASA Technical Reports Server (NTRS)

Svalbonas, V.; Levine, H.; Ogilvie, P.

1975-01-01

Engineering programming information is presented for the STARS-2P (shell theory automated for rotational structures-2P (plasticity)) digital computer program, and FORTRAN 4 was used in writing the various subroutines. The execution of this program requires the use of thirteen temporary storage units. The program was initially written and debugged on the IBM 370-165 computer and converted to the UNIVAC 1108 computer, where it utilizes approximately 60,000 words of core. Only basic FORTRAN library routines are required by the program: sine, cosine, absolute value, and square root.

Architecture Adaptive Computing Environment

NASA Technical Reports Server (NTRS)

Dorband, John E.

2006-01-01

Architecture Adaptive Computing Environment (aCe) is a software system that includes a language, compiler, and run-time library for parallel computing. aCe was developed to enable programmers to write programs, more easily than was previously possible, for a variety of parallel computing architectures. Heretofore, it has been perceived to be difficult to write parallel programs for parallel computers and more difficult to port the programs to different parallel computing architectures. In contrast, aCe is supportable on all high-performance computing architectures. Currently, it is supported on LINUX clusters. aCe uses parallel programming constructs that facilitate writing of parallel programs. Such constructs were used in single-instruction/multiple-data (SIMD) programming languages of the 1980s, including Parallel Pascal, Parallel Forth, C*, *LISP, and MasPar MPL. In aCe, these constructs are extended and implemented for both SIMD and multiple- instruction/multiple-data (MIMD) architectures. Two new constructs incorporated in aCe are those of (1) scalar and virtual variables and (2) pre-computed paths. The scalar-and-virtual-variables construct increases flexibility in optimizing memory utilization in various architectures. The pre-computed-paths construct enables the compiler to pre-compute part of a communication operation once, rather than computing it every time the communication operation is performed.

Guidelines for developing vectorizable computer programs

NASA Technical Reports Server (NTRS)

Miner, E. W.

1982-01-01

Some fundamental principles for developing computer programs which are compatible with array-oriented computers are presented. The emphasis is on basic techniques for structuring computer codes which are applicable in FORTRAN and do not require a special programming language or exact a significant penalty on a scalar computer. Researchers who are using numerical techniques to solve problems in engineering can apply these basic principles and thus develop transportable computer programs (in FORTRAN) which contain much vectorizable code. The vector architecture of the ASC is discussed so that the requirements of array processing can be better appreciated. The "vectorization" of a finite-difference viscous shock-layer code is used as an example to illustrate the benefits and some of the difficulties involved. Increases in computing speed with vectorization are illustrated with results from the viscous shock-layer code and from a finite-element shock tube code. The applicability of these principles was substantiated through running programs on other computers with array-associated computing characteristics, such as the Hewlett-Packard (H-P) 1000-F.

MPI implementation of PHOENICS: A general purpose computational fluid dynamics code

NASA Astrophysics Data System (ADS)

Simunovic, S.; Zacharia, T.; Baltas, N.; Spalding, D. B.

1995-03-01

PHOENICS is a suite of computational analysis programs that are used for simulation of fluid flow, heat transfer, and dynamical reaction processes. The parallel version of the solver EARTH for the Computational Fluid Dynamics (CFD) program PHOENICS has been implemented using Message Passing Interface (MPI) standard. Implementation of MPI version of PHOENICS makes this computational tool portable to a wide range of parallel machines and enables the use of high performance computing for large scale computational simulations. MPI libraries are available on several parallel architectures making the program usable across different architectures as well as on heterogeneous computer networks. The Intel Paragon NX and MPI versions of the program have been developed and tested on massively parallel supercomputers Intel Paragon XP/S 5, XP/S 35, and Kendall Square Research, and on the multiprocessor SGI Onyx computer at Oak Ridge National Laboratory. The preliminary testing results of the developed program have shown scalable performance for reasonably sized computational domains.

MPI implementation of PHOENICS: A general purpose computational fluid dynamics code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simunovic, S.; Zacharia, T.; Baltas, N.

1995-04-01

PHOENICS is a suite of computational analysis programs that are used for simulation of fluid flow, heat transfer, and dynamical reaction processes. The parallel version of the solver EARTH for the Computational Fluid Dynamics (CFD) program PHOENICS has been implemented using Message Passing Interface (MPI) standard. Implementation of MPI version of PHOENICS makes this computational tool portable to a wide range of parallel machines and enables the use of high performance computing for large scale computational simulations. MPI libraries are available on several parallel architectures making the program usable across different architectures as well as on heterogeneous computer networks. Themore » Intel Paragon NX and MPI versions of the program have been developed and tested on massively parallel supercomputers Intel Paragon XP/S 5, XP/S 35, and Kendall Square Research, and on the multiprocessor SGI Onyx computer at Oak Ridge National Laboratory. The preliminary testing results of the developed program have shown scalable performance for reasonably sized computational domains.« less

Digital computer technique for setup and checkout of an analog computer

NASA Technical Reports Server (NTRS)

Ambaruch, R.

1968-01-01

Computer program technique, called Analog Computer Check-Out Routine Digitally /ACCORD/, generates complete setup and checkout data for an analog computer. In addition, the correctness of the analog program implementation is validated.

Hybrid Geothermal Heat Pumps for Cooling Telecommunications Data Centers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beckers, Koenraad J; Zurmuhl, David P.; Lukawski, Maciej Z.

The technical and economic performance of geothermal heat pump (GHP) systems supplying year-round cooling to representative small data centers with cooling loads less than 500 kWth were analyzed and compared to air-source heat pumps (ASHPs). A numerical model was developed in TRNSYS software to simulate the operation of air-source and geothermal heat pumps with and without supplementary air cooled heat exchangers - dry coolers (DCs). The model was validated using data measured at an experimental geothermal system installed in Ithaca, NY, USA. The coefficient of performance (COP) and cooling capacity of the GHPs were calculated over a 20-year lifetime andmore » compared to the performance of ASHPs. The total cost of ownership (TCO) of each of the cooling systems was calculated to assess its economic performance. Both the length of the geothermal borehole heat exchangers (BHEs) and the dry cooler temperature set point were optimized to minimize the TCO of the geothermal systems. Lastly, a preliminary analysis of the performance of geothermal heat pumps for cooling dominated systems was performed for other locations including Dallas, TX, Sacramento, CA, and Minneapolis, MN.« less

Performance of Radiant Heating Systems of Low-Energy Buildings

NASA Astrophysics Data System (ADS)

Sarbu, Ioan; Mirza, Matei; Crasmareanu, Emanuel

2017-10-01

After the introduction of plastic piping, the application of water-based radiant heating with pipes embedded in room surfaces (i.e., floors, walls, and ceilings), has significantly increased worldwide. Additionally, interest and growth in radiant heating and cooling systems have increased in recent years because they have been demonstrated to be energy efficient in comparison to all-air distribution systems. This paper briefly describes the heat distribution systems in buildings, focusing on the radiant panels (floor, wall, ceiling, and floor-ceiling). Main objective of this study is the performance investigation of different types of low-temperature heating systems with different methods. Additionally, a comparative analysis of the energy, environmental, and economic performances of floor, wall, ceiling, and floor-ceiling heating using numerical simulation with Transient Systems Simulation (TRNSYS) software is performed. This study showed that the floor-ceiling heating system has the best performance in terms of the lowest energy consumption, operation cost, CO2 emission, and the nominal boiler power. The comparison of the room operative air temperatures and the set-point operative air temperature indicates also that all radiant panel systems provide satisfactory results without significant deviations.

Assessment of energy and economic performance of office building models: a case study

NASA Astrophysics Data System (ADS)

Song, X. Y.; Ye, C. T.; Li, H. S.; Wang, X. L.; Ma, W. B.

2016-08-01

Energy consumption of building accounts for more than 37.3% of total energy consumption while the proportion of energy-saving buildings is just 5% in China. In this paper, in order to save potential energy, an office building in Southern China was selected as a test example for energy consumption characteristics. The base building model was developed by TRNSYS software and validated against the recorded data from the field work in six days out of August-September in 2013. Sensitivity analysis was conducted for energy performance of building envelope retrofitting; five envelope parameters were analyzed for assessing the thermal responses. Results indicated that the key sensitivity factors were obtained for the heat-transfer coefficient of exterior walls (U-wall), infiltration rate and shading coefficient (SC), of which the sum sensitivity factor was about 89.32%. In addition, the results were evaluated in terms of energy and economic analysis. The analysis of sensitivity validated against some important results of previous studies. On the other hand, the cost-effective method improved the efficiency of investment management in building energy.

Building America Case Study: The Impact of Thermostat Placement in Low-Load Homes in Sunny Climates, Denver, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Modern, energy-efficient homes conforming to the Zero Energy Ready Home standard face the challenge of meeting high customer expectations for comfort. Traditional heating, ventilation, and air conditioning (HVAC) sizing and control strategies may be insufficient to adequately condition each zone due to unique load patterns in each room caused by a number of factors. These factors include solar heat gains, occupant-related gains, and gains associated with appliances and electronics. Because of shrinking shell loads, these intermittent factors are having an increasingly significant impact on the thermal load in each zone. Consequently, occupant comfort can be compromised. To evaluate the impactmore » of climate and house geometry, as well as HVAC system and control strategies on comfort conditions, IBACOS analyzed the results of 99 TRNSYS multiple-zone simulations. The results of this analysis indicate that for simple-geometry and single-story plans, a single zone and thermostat can adequately condition the entire house. Demanding house geometry and houses with multiple stories require the consideration of multiple thermostats and multiple zones.« less

Research and application of an intelligent control system in central air-conditioning based on energy consumption simulation

NASA Astrophysics Data System (ADS)

Cao, Ling; Che, Wenbin

2018-05-01

For the central air-conditioning energy-saving, it is common practice to use a wide range of PTD controllers in engineering to optimize energy savings. However, the shortcomings of the PTD controller have also been magnified on this issue, such as: calculation accuracy is not enough, the calculation time is too long. Particle swarm optimization has the advantage of fast convergence. This paper is based on Particle Swarm Optimization apply in PTD controller tuning parameters in order to achieve the purpose of saving energy while ensuring comfort. The algorithm proposed in this paper can adjust the weight according to the change of population fitness, reduce the weights of particles with lower fitness and enhance the weights of particles with higher fitness in the population, and fully release the population vitality. The method in this paper is validated by the TRNSYS model based on the central air-conditioning system. The experimental results show that the room temperature fluctuation is small, the overshoot is small, the adjustment speed is fast, and the energy-saving fluctuates at 10%.

Risk Assessment of Heating, Ventilating, and Air-Conditioning Strategies in Low-Load Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poerschke, Andrew

2016-02-17

"Modern, energy efficient homes conforming to the Zero Energy Ready Home standard face the challenge of meeting high customer expectations for comfort. Traditional heating, ventilation, and air conditioning (HVAC) sizing and control strategies may be insufficient to adequately condition each zone due to unique load patterns in each room caused by a number of factors. These factors include solar heat gains, occupant-related gains, and gains associated with appliances and electronics. Because of shrinking shell loads, these intermittent factors are having an increasingly significant impact on the thermal load in each zone. Consequently, occupant comfort can be compromised. To evaluate themore » impact of climate and house geometry, as well as HVAC system and control strategies on comfort conditions, IBACOS analyzed the results of 99 TRNSYS multiple-zone simulations. The results of this analysis indicate that for simple-geometry and single-story plans, a single zone and thermostat can adequately condition the entire house. Demanding house geometry and houses with multiple stories require the consideration of multiple thermostats and multiple zones.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, C Keith; Uselton, Robert B.; Shen, Bo

A residential-sized dual air-source integrated heat pump (AS-IHP) concept is under development in partnership between ORNL and a manufacturer. The concept design consists of a two-stage air-source heat pump (ASHP) coupled on the air distribution side with a separate novel water heating/dehumidification (WH/DH) module. The motivation for this unusual equipment combination is the forecast trend for home sensible loads to be reduced more than latent loads. Integration of water heating with a space dehumidification cycle addresses humidity control while performing double-duty. This approach can be applied to retrofit/upgrade applications as well as new construction. A WH/DH module capable of ~1.47more » L/h water removal and ~2 kW water heating capacity was assembled by the manufacturer. A heat pump system model was used to guide the controls design; lab testing was conducted and used to calibrate the models. Performance maps were generated and used in a TRNSYS sub-hourly simulation to predict annual performance in a well-insulated house. Annual HVAC/WH energy savings of ~35% are predicted in cold and hot-humid U.S. climates compared to a minimum efficiency baseline.« less

Solar Assisted Ground Source Heat Pump Performance in Nearly Zero Energy Building in Baltic Countries

NASA Astrophysics Data System (ADS)

Januševičius, Karolis; Streckienė, Giedrė

2013-12-01

In near zero energy buildings (NZEB) built in Baltic countries, heat production systems meet the challenge of large share domestic hot water demand and high required heating capacity. Due to passive solar design, cooling demand in residential buildings also needs an assessment and solution. Heat pump systems are a widespread solution to reduce energy use. A combination of heat pump and solar thermal collectors helps to meet standard requirements and increases the share of renewable energy use in total energy balance of country. The presented paper describes a simulation study of solar assisted heat pump systems carried out in TRNSYS. The purpose of this simulation was to investigate how the performance of a solar assisted heat pump combination varies in near zero energy building. Results of three systems were compared to autonomous (independent) systems simulated performance. Different solar assisted heat pump design solutions with serial and parallel solar thermal collector connections to the heat pump loop were modelled and a passive cooling possibility was assessed. Simulations were performed for three Baltic countries: Lithuania, Latvia and Estonia.

Report on the FY17 Development of Computer Program for ASME Section III, Division 5, Subsection HB, Subpart B Rules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swindeman, M. J.; Jetter, R. I.; Sham, T. -L.

One of the objectives of the high temperature design methodology activities is to develop and validate both improvements and the basic features of ASME Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Facility Components, Division 5, High Temperature Reactors, Subsection HB, Subpart B (HBB). The overall scope of this task is to develop a computer program to aid assessment procedures of components under specified loading conditions in accordance with the elevated temperature design requirements for Division 5 Class A components. There are many features and alternative paths of varying complexity in HBB. The initial focus ofmore » this computer program is a basic path through the various options for a single reference material, 316H stainless steel. However, the computer program is being structured for eventual incorporation all of the features and permitted materials of HBB. This report will first provide a description of the overall computer program, particular challenges in developing numerical procedures for the assessment, and an overall approach to computer program development. This is followed by a more comprehensive appendix, which is the draft computer program manual for the program development. The strain limits rules have been implemented in the computer program. The evaluation of creep-fatigue damage will be implemented in future work scope.« less

32 CFR 505.13 - Computer Matching Agreement Program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 3 2010-07-01 2010-07-01 true Computer Matching Agreement Program. 505.13 Section 505.13 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS ARMY PRIVACY ACT PROGRAM § 505.13 Computer Matching Agreement Program. (a...

Computers and Young Children. Storyboard Software: Flannel Boards in the Computer Age.

ERIC Educational Resources Information Center

Shade, Daniel D.

1995-01-01

Describes storyboard software as computer programs with which children can build a story using visuals. Notes the importance of such programs from preliterate or nonreading children. Describes a new storyboard program, "Wiggins in Storyland," and its features. Lists recommended storyboard software programs, with publishers and compatible…

ROUTES: a computer program for preliminary route location.

Treesearch

S.E. Reutebuch

1988-01-01

An analytical description of the ROUTES computer program is presented. ROUTES is part of the integrated preliminary harvest- and transportation-planning software package, PLANS. The ROUTES computer program is useful where grade and sideslope limitations are important in determining routes for vehicular travel. With the program, planners can rapidly identify route...

Debugging a high performance computing program

DOEpatents

Gooding, Thomas M.

2014-08-19

Methods, apparatus, and computer program products are disclosed for debugging a high performance computing program by gathering lists of addresses of calling instructions for a plurality of threads of execution of the program, assigning the threads to groups in dependence upon the addresses, and displaying the groups to identify defective threads.

Middle School Teachers' Perceptions of Computer-Assisted Reading Intervention Programs

ERIC Educational Resources Information Center

Bippert, Kelli; Harmon, Janis

2017-01-01

Middle schools often turn to computer-assisted reading intervention programs to improve student reading. The questions guiding this study are (a) in what ways are computer-assisted reading intervention programs utilized, and (b) what are teachers' perceptions about these intervention programs? Nineteen secondary reading teachers were interviewed…

Space shuttle environmental and thermal control life support system computer program

NASA Technical Reports Server (NTRS)

1972-01-01

A computer program for the design and operation of the space shuttle environmental and thermal control life support system is presented. The subjects discussed are: (1) basic optimization program, (2) off design performance, (3) radiator/evaporator expendable usage, (4) component weights, and (5) computer program operating procedures.

Debugging a high performance computing program

DOEpatents

Gooding, Thomas M.

2013-08-20

Methods, apparatus, and computer program products are disclosed for debugging a high performance computing program by gathering lists of addresses of calling instructions for a plurality of threads of execution of the program, assigning the threads to groups in dependence upon the addresses, and displaying the groups to identify defective threads.

Integrated Heat Pump HVAC Systems for Near-Zero-Energy Homes - Business Case Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baxter, Van D

2007-05-01

The long range strategic goal of the Department of Energy's Building Technologies (DOE/BT) Program is to create, by 2020, technologies and design approaches that enable the construction of net-zero energy homes at low incremental cost (DOE/BT 2005). A net zero energy home (NZEH) is a residential building with greatly reduced needs for energy through efficiency gains, with the balance of energy needs supplied by renewable technologies. While initially focused on new construction, these technologies and design approaches are intended to have application to buildings constructed before 2020 as well resulting in substantial reduction in energy use for all building typesmore » and ages. DOE/BT's Emerging Technologies (ET) team is working to support this strategic goal by identifying and developing advanced heating, ventilating, air-conditioning, and water heating (HVAC/WH) technology options applicable to NZEHs. Although the energy efficiency of heating, ventilating, and air-conditioning (HVAC) equipment has increased substantially in recent years, new approaches are needed to continue this trend. Dramatic efficiency improvements are necessary to enable progress toward the NZEH goals, and will require a radical rethinking of opportunities to improve system performance. The large reductions in HVAC energy consumption necessary to support the NZEH goals require a systems-oriented analysis approach that characterizes each element of energy consumption, identifies alternatives, and determines the most cost-effective combination of options. In particular, HVAC equipment must be developed that addresses the range of special needs of NZEH applications in the areas of reduced HVAC and water heating energy use, humidity control, ventilation, uniform comfort, and ease of zoning. In FY05 ORNL conducted an initial Stage 1 (Applied Research) scoping assessment of HVAC/WH systems options for future NZEHs to help DOE/BT identify and prioritize alternative approaches for further development. Eleven system concepts with central air distribution ducting and nine multi-zone systems were selected and their annual and peak demand performance estimated for five locations: Atlanta (mixed-humid), Houston (hot-humid), Phoenix (hot-dry), San Francisco (marine), and Chicago (cold). Performance was estimated by simulating the systems using the TRNSYS simulation engine (Solar Energy Laboratory et al. 2006) in two 1800-ft{sup 2} houses--a Building America (BA) benchmark house and a prototype NZEH taken from BEopt results at the take-off (or crossover) point (i.e., a house incorporating those design features such that further progress towards ZEH is through the addition of photovoltaic power sources, as determined by current BEopt analyses conducted by NREL). Results were summarized in a project report, 'HVAC Equipment Design options for Near-Zero-Energy Homes--A Stage 2 Scoping Assessment', ORNL/TM-2005/194 (Baxter 2005). The 2005 study report describes the HVAC options considered, the ranking criteria used, and the system rankings by priority. Table 1 summarizes the energy savings potential of the highest scoring options from the 2005 study for all five locations. All system options were scored by the ORNL building equipment research team and by William Goetzler of Navigant Consulting. These scores were reviewed by DOE/BT's Residential Integration program leaders and Building America team members. Based on these results, the two centrally ducted integrated heat pump (IHP) systems (air source and ground source versions) were selected for advancement to Stage 2 (Exploratory Development) business case assessments in FY06. This report describes results of these business case assessments. It is a compilation of three separate reports describing the initial business case study (Baxter 2006a), an update to evaluate the impact of an economizer cooling option (Baxter 2006b), and a second update to evaluate the impact of a winter humidification option (Baxter 2007). In addition it reports some corrections made subsequent to release of the first two reports to correct some errors in the TRNSYS building model for Atlanta and in the refrigerant pressure drop calculation in the water-to-refrigerant evaporator module of the ORNL Heat Pump Design Model (HPDM) used for the IHP analyses. These changes resulted in some minor differences between IHP performance as reported in Baxter (2006a, b) and in this report.« less

Culvert analysis program for indirect measurement of discharge

USGS Publications Warehouse

Fulford, Janice M.; ,

1993-01-01

A program based on the U.S. Geological Survey (USGS) methods for indirectly computing peak discharges through culverts allows users to employ input data formats used by the water surface profile program (WSPRO). The program can be used to compute discharge rating surfaces or curves that describe the behavior of flow through a particular culvert or to compute discharges from measurements of upstream of the gradually varied flow equations and has been adapted slightly to provide solutions that minimize the need for the user to determine between different flow regimes. The program source is written in Fortran 77 and has been run on mini-computers and personal computers. The program does not use or require graphics capability, a color monitor, or a mouse.

An Exploration of the Role of Visual Programming Tools in the Development of Young Children's Computational Thinking

ERIC Educational Resources Information Center

Rose, Simon P.; Habgood, M. P. Jacob; Jay, Tim

2017-01-01

Programming tools are being used in education to teach computer science to children as young as 5 years old. This research aims to explore young children's approaches to programming in two tools with contrasting programming interfaces, ScratchJr and Lightbot, and considers the impact of programming approaches on developing computational thinking.…

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCaskey, Alexander J.

Hybrid programming models for beyond-CMOS technologies will prove critical for integrating new computing technologies alongside our existing infrastructure. Unfortunately the software infrastructure required to enable this is lacking or not available. XACC is a programming framework for extreme-scale, post-exascale accelerator architectures that integrates alongside existing conventional applications. It is a pluggable framework for programming languages developed for next-gen computing hardware architectures like quantum and neuromorphic computing. It lets computational scientists efficiently off-load classically intractable work to attached accelerators through user-friendly Kernel definitions. XACC makes post-exascale hybrid programming approachable for domain computational scientists.

Evaluation of Rankine cycle air conditioning system hardware by computer simulation

NASA Technical Reports Server (NTRS)

Healey, H. M.; Clark, D.

1978-01-01

A computer program for simulating the performance of a variety of solar powered Rankine cycle air conditioning system components (RCACS) has been developed. The computer program models actual equipment by developing performance maps from manufacturers data and is capable of simulating off-design operation of the RCACS components. The program designed to be a subroutine of the Marshall Space Flight Center (MSFC) Solar Energy System Analysis Computer Program 'SOLRAD', is a complete package suitable for use by an occasional computer user in developing performance maps of heating, ventilation and air conditioning components.

75 FR 53004 - Privacy Act of 1974, as Amended; Notice of Computer-Matching Program (Railroad Retirement Board...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-30

... report of this computer-matching program with the Committee on Homeland Security and Governmental Affairs... INFORMATION: A. General The Computer-Matching and Privacy Protection Act of 1988, (Pub. L. 100-503), amended... RAILROAD RETIREMENT BOARD Privacy Act of 1974, as Amended; Notice of Computer-Matching Program...

Structural Optimization Methodology for Rotating Disks of Aircraft Engines

NASA Technical Reports Server (NTRS)

Armand, Sasan C.

1995-01-01

In support of the preliminary evaluation of various engine technologies, a methodology has been developed for structurally designing the rotating disks of an aircraft engine. The structural design methodology, along with a previously derived methodology for predicting low-cycle fatigue life, was implemented in a computer program. An interface computer program was also developed that gathers the required data from a flowpath analysis program (WATE) being used at NASA Lewis. The computer program developed for this study requires minimum interaction with the user, thus allowing engineers with varying backgrounds in aeropropulsion to successfully execute it. The stress analysis portion of the methodology and the computer program were verified by employing the finite element analysis method. The 10th- stage, high-pressure-compressor disk of the Energy Efficient Engine Program (E3) engine was used to verify the stress analysis; the differences between the stresses and displacements obtained from the computer program developed for this study and from the finite element analysis were all below 3 percent for the problem solved. The computer program developed for this study was employed to structurally optimize the rotating disks of the E3 high-pressure compressor. The rotating disks designed by the computer program in this study were approximately 26 percent lighter than calculated from the E3 drawings. The methodology is presented herein.

DORCA 2 computer program. Volume 3: Program listing

NASA Technical Reports Server (NTRS)

Carey, J. B.

1972-01-01

A program listing for the Dynamic Operational Requirements and Cost Analysis Program is presented. Detailed instructions for the computer programming involved in space mission planning and project requirements are developed.

A vectorization of the Hess McDonnell Douglas potential flow program NUED for the STAR-100 computer

NASA Technical Reports Server (NTRS)

Boney, L. R.; Smith, R. E., Jr.

1979-01-01

The computer program NUED for analyzing potential flow about arbitrary three dimensional lifting bodies using the panel method was modified to use vector operations and run on the STAR-100 computer. A high speed of computation and ability to approximate the body surface with a large number of panels are characteristics of NUEDV. The new program shows that vector operations can be readily implemented in programs of this type to increase the computational speed on the STAR-100 computer. The virtual memory architecture of the STAR-100 facilitates the use of large numbers of panels to approximate the body surface.

CHIRAL--A Computer Aided Application of the Cahn-Ingold-Prelog Rules.

ERIC Educational Resources Information Center

Meyer, Edgar F., Jr.

1978-01-01

A computer program is described for identification of chiral centers in molecules. Essential input to the program includes both atomic and bonding information. The program does not require computer graphic input-output. (BB)

Software Maintenance of the Subway Environment Simulation Computer Program

DOT National Transportation Integrated Search

1980-12-01

This document summarizes the software maintenance activities performed to support the Subway Environment Simulation (SES) Computer Program. The SES computer program is a design-oriented analytic tool developed during a recent five-year research proje...

Translator program converts computer printout into braille language

NASA Technical Reports Server (NTRS)

Powell, R. A.

1967-01-01

Computer program converts print image tape files into six dot Braille cells, enabling a blind computer programmer to monitor and evaluate data generated by his own programs. The Braille output is printed 8 lines per inch.

Improved programs for DNA and protein sequence analysis on the IBM personal computer and other standard computer systems.

PubMed Central

Mount, D W; Conrad, B

1986-01-01

We have previously described programs for a variety of types of sequence analysis (1-4). These programs have now been integrated into a single package. They are written in the standard C programming language and run on virtually any computer system with a C compiler, such as the IBM/PC and other computers running under the MS/DOS and UNIX operating systems. The programs are widely distributed and may be obtained from the authors as described below. PMID:3753780

Computer program for design and performance analysis of navigation-aid power systems. Program documentation. Volume 1: Software requirements document

NASA Technical Reports Server (NTRS)

Goltz, G.; Kaiser, L. M.; Weiner, H.

1977-01-01

A computer program has been developed for designing and analyzing the performance of solar array/battery power systems for the U.S. Coast Guard Navigational Aids. This program is called the Design Synthesis/Performance Analysis (DSPA) Computer Program. The basic function of the Design Synthesis portion of the DSPA program is to evaluate functional and economic criteria to provide specifications for viable solar array/battery power systems. The basic function of the Performance Analysis portion of the DSPA program is to simulate the operation of solar array/battery power systems under specific loads and environmental conditions. This document establishes the software requirements for the DSPA computer program, discusses the processing that occurs within the program, and defines the necessary interfaces for operation.

Orthorectification by Using Gpgpu Method

NASA Astrophysics Data System (ADS)

Sahin, H.; Kulur, S.

2012-07-01

Thanks to the nature of the graphics processing, the newly released products offer highly parallel processing units with high-memory bandwidth and computational power of more than teraflops per second. The modern GPUs are not only powerful graphic engines but also they are high level parallel programmable processors with very fast computing capabilities and high-memory bandwidth speed compared to central processing units (CPU). Data-parallel computations can be shortly described as mapping data elements to parallel processing threads. The rapid development of GPUs programmability and capabilities attracted the attentions of researchers dealing with complex problems which need high level calculations. This interest has revealed the concepts of "General Purpose Computation on Graphics Processing Units (GPGPU)" and "stream processing". The graphic processors are powerful hardware which is really cheap and affordable. So the graphic processors became an alternative to computer processors. The graphic chips which were standard application hardware have been transformed into modern, powerful and programmable processors to meet the overall needs. Especially in recent years, the phenomenon of the usage of graphics processing units in general purpose computation has led the researchers and developers to this point. The biggest problem is that the graphics processing units use different programming models unlike current programming methods. Therefore, an efficient GPU programming requires re-coding of the current program algorithm by considering the limitations and the structure of the graphics hardware. Currently, multi-core processors can not be programmed by using traditional programming methods. Event procedure programming method can not be used for programming the multi-core processors. GPUs are especially effective in finding solution for repetition of the computing steps for many data elements when high accuracy is needed. Thus, it provides the computing process more quickly and accurately. Compared to the GPUs, CPUs which perform just one computing in a time according to the flow control are slower in performance. This structure can be evaluated for various applications of computer technology. In this study covers how general purpose parallel programming and computational power of the GPUs can be used in photogrammetric applications especially direct georeferencing. The direct georeferencing algorithm is coded by using GPGPU method and CUDA (Compute Unified Device Architecture) programming language. Results provided by this method were compared with the traditional CPU programming. In the other application the projective rectification is coded by using GPGPU method and CUDA programming language. Sample images of various sizes, as compared to the results of the program were evaluated. GPGPU method can be used especially in repetition of same computations on highly dense data, thus finding the solution quickly.

Confronting the Issues of Programming in Information Systems Curricula: The Goal Is Success

ERIC Educational Resources Information Center

Babb, Jeffry; Longenecker, Herbert E., Jr.; Baugh, Jeanne; Feinstein, David

2014-01-01

Computer programming has been part of Information Systems (IS) curricula since the first model curriculum. It is with programming that computers are instructed how to implement our ideas into reality. Yet, over the last decade numbers of computing undergraduates have significantly declined in North American academic programs. In addition, high…

Numerical nonlinear inelastic analysis of stiffened shells of revolution. Volume 4: Satellite-1P program for STARS-2P digital computer program

NASA Technical Reports Server (NTRS)

Svalbonas, V.; Ogilvie, P.

1975-01-01

A special data debugging package called SAT-1P created for the STARS-2P computer program is described. The program was written exclusively in FORTRAN 4 for the IBM 370-165 computer, and then converted to the UNIVAC 1108.

A Computer-Aided Writing Program for Learning Disabled Adolescents.

ERIC Educational Resources Information Center

Fais, Laurie; Wanderman, Richard

The paper describes the application of a computer-assisted writing program in a special high school for learning disabled and dyslexic students and reports on a study of the program's effectiveness. Particular advantages of the Macintosh Computer for such a program are identified including use of the mouse pointing tool, graphic icons to identify…

01010000 01001100 01000001 01011001: Play Elements in Computer Programming

ERIC Educational Resources Information Center

Breslin, Samantha

2013-01-01

This article explores the role of play in human interaction with computers in the context of computer programming. The author considers many facets of programming including the literary practice of coding, the abstract design of programs, and more mundane activities such as testing, debugging, and hacking. She discusses how these incorporate the…

A Proposed Programming System for Knuth's Mix Computer.

ERIC Educational Resources Information Center

Akers, Max Neil

A programing system using a hypothetical computer is proposed for use in teaching machine and assembly language programing courses. Major components such as monitor, assembler, interpreter, grader, and diagnostics are described. The interpreter is programed and documented for use on an IBM 360/67 computer. The interpreter can be used for teaching…

Some Analogies between Computer Programming and the Composing Process.

ERIC Educational Resources Information Center

Skulicz, Matthew

Since there are similarities between the process of writing computer programs and the process of writing successful expository prose, a student's knowledge of computer programing can contribute to the understanding of some principles of composition. The establishment of a clear objective is the first priority of both the writer and the programer,…

Base Numeration Systems and Introduction to Computer Programming.

ERIC Educational Resources Information Center

Kim, K. Ed.; And Others

This teaching guide is for the instructor of an introductory course in computer programming using FORTRAN language. Five FORTRAN programs are incorporated in this guide, which has been used as a FORTRAN IV SELF TEACHER. The base eight, base four, and base two concepts are integrated with FORTRAN computer programs, geoblock activities, and related…

40 CFR Appendix C to Part 67 - Computer Program

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 15 2011-07-01 2011-07-01 false Computer Program C Appendix C to Part... APPROVAL OF STATE NONCOMPLIANCE PENALTY PROGRAM Pt. 67, App. C Appendix C to Part 67—Computer Program Note: EPA will make copies of appendix C available from: Director, Stationary Source Compliance Division, EN...

Personalized Computer-Assisted Mathematics Problem-Solving Program and Its Impact on Taiwanese Students

ERIC Educational Resources Information Center

Chen, Chiu-Jung; Liu, Pei-Lin

2007-01-01

This study evaluated the effects of a personalized computer-assisted mathematics problem-solving program on the performance and attitude of Taiwanese fourth grade students. The purpose of this study was to determine whether the personalized computer-assisted program improved student performance and attitude over the nonpersonalized program.…

Design and Curriculum Considerations for a Computer Graphics Program in the Arts.

ERIC Educational Resources Information Center

Leeman, Ruedy W.

This history and state-of-the-art review of computer graphics describes computer graphics programs and proposed programs at Sheridan College (Canada), the Rhode Island School of Design, the University of Oregon, Northern Illinois University, and Ohio State University. These programs are discussed in terms of their philosophy, curriculum, student…

37 CFR 201.40 - Exemption to prohibition against circumvention.

Code of Federal Regulations, 2012 CFR

2012-07-01

... security of the owner or operator of a computer, computer system, or computer network; and (ii) The... film and media studies students; (ii) Documentary filmmaking; (iii) Noncommercial videos. (2) Computer... lawfully obtained, with computer programs on the telephone handset. (3) Computer programs, in the form of...

Method and computer program product for maintenance and modernization backlogging

DOEpatents

Mattimore, Bernard G; Reynolds, Paul E; Farrell, Jill M

2013-02-19

According to one embodiment, a computer program product for determining future facility conditions includes a computer readable medium having computer readable program code stored therein. The computer readable program code includes computer readable program code for calculating a time period specific maintenance cost, for calculating a time period specific modernization factor, and for calculating a time period specific backlog factor. Future facility conditions equal the time period specific maintenance cost plus the time period specific modernization factor plus the time period specific backlog factor. In another embodiment, a computer-implemented method for calculating future facility conditions includes calculating a time period specific maintenance cost, calculating a time period specific modernization factor, and calculating a time period specific backlog factor. Future facility conditions equal the time period specific maintenance cost plus the time period specific modernization factor plus the time period specific backlog factor. Other embodiments are also presented.

Program listing for the REEDM (Rocket Exhaust Effluent Diffusion Model) computer program

NASA Technical Reports Server (NTRS)

Bjorklund, J. R.; Dumbauld, R. K.; Cheney, C. S.; Geary, H. V.

1982-01-01

The program listing for the REEDM Computer Program is provided. A mathematical description of the atmospheric dispersion models, cloud-rise models, and other formulas used in the REEDM model; vehicle and source parameters, other pertinent physical properties of the rocket exhaust cloud and meteorological layering techniques; user's instructions for the REEDM computer program; and worked example problems are contained in NASA CR-3646.

Controlling Laboratory Processes From A Personal Computer

NASA Technical Reports Server (NTRS)

Will, H.; Mackin, M. A.

1991-01-01

Computer program provides natural-language process control from IBM PC or compatible computer. Sets up process-control system that either runs without operator or run by workers who have limited programming skills. Includes three smaller programs. Two of them, written in FORTRAN 77, record data and control research processes. Third program, written in Pascal, generates FORTRAN subroutines used by other two programs to identify user commands with device-driving routines written by user. Also includes set of input data allowing user to define user commands to be executed by computer. Requires personal computer operating under MS-DOS with suitable hardware interfaces to all controlled devices. Also requires FORTRAN 77 compiler and device drivers written by user.

User's Guide for Computer Program that Routes Signal Traces

NASA Technical Reports Server (NTRS)

Hedgley, David R., Jr.

2000-01-01

This disk contains both a FORTRAN computer program and the corresponding user's guide that facilitates both its incorporation into your system and its utility. The computer program represents an efficient algorithm that routes signal traces on layers of a printed circuit with both through-pins and surface mounts. The computer program included is an implementation of the ideas presented in the theoretical paper titled "A Formal Algorithm for Routing Signal Traces on a Printed Circuit Board", NASA TP-3639 published in 1996. The computer program in the "connects" file can be read with a FORTRAN compiler and readily integrated into software unique to each particular environment where it might be used.

Energy consumption program: A computer model simulating energy loads in buildings

NASA Technical Reports Server (NTRS)

Stoller, F. W.; Lansing, F. L.; Chai, V. W.; Higgins, S.

1978-01-01

The JPL energy consumption computer program developed as a useful tool in the on-going building modification studies in the DSN energy conservation project is described. The program simulates building heating and cooling loads and computes thermal and electric energy consumption and cost. The accuracy of computations are not sacrificed, however, since the results lie within + or - 10 percent margin compared to those read from energy meters. The program is carefully structured to reduce both user's time and running cost by asking minimum information from the user and reducing many internal time-consuming computational loops. Many unique features were added to handle two-level electronics control rooms not found in any other program.

76 FR 12984 - Privacy Act of 1974; Notice of a Computer Matching Program Between HUD and the United States...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-09

... of a Computer Matching Program Between HUD and the United States Department of Veterans Affairs (VA) AGENCY: Office of the Chief Information Officer, HUD. ACTION: Notice of a computer matching program... the Computer Matching and Privacy Protection Act of 1988 (Pub. L. 100-503), and the Office of...

A Successful Bootstrap Program for Infusion of Computer Competencies into a School of Education Curriculum.

ERIC Educational Resources Information Center

Van Dusseldorp, Ralph

1984-01-01

Describes the successful, low-cost program for infusion of computer competencies into the curriculum of the School of Education at the University of Alaska, Anchorage, where all students are required to become computer competent prior to graduation. Computer competency goals for students in school's certification programs are outlined. (MBR)

78 FR 71591 - Privacy Act of 1974; Computer Matching Program between the U.S. Department of Education (ED) and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-29

... DEPARTMENT OF EDUCATION Privacy Act of 1974; Computer Matching Program between the U.S. Department.... ACTION: Notice. SUMMARY: Notice is hereby given of the renewal of the computer matching program between... (VA) (source agency). After the ED and VA Data Integrity Boards approve a new computer matching...

78 FR 29786 - Computer Matching and Privacy Protection Act of 1988; Report of Matching Program: RRB and State...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-21

... RAILROAD RETIREMENT BOARD Computer Matching and Privacy Protection Act of 1988; Report of Matching...: Notice of a renewal of an existing computer matching program due to expire on May 24, 2013. SUMMARY: As... of its intent to renew an ongoing computer matching program. In this match, we provide certain...

78 FR 70971 - Privacy Act of 1974, as Amended; Notice of Computer Matching Program (Railroad Retirement Board...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-27

... will file a report of this computer-matching program with the Committee on Homeland Security and... . SUPPLEMENTARY INFORMATION: A. General The Computer Matching and Privacy Protection Act of 1988, (Pub. L. 100-503... RAILROAD RETIREMENT BOARD Privacy Act of 1974, as Amended; Notice of Computer Matching Program...

76 FR 50460 - Privacy Act of 1974; Notice of a Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-15

...; Notice of a Computer Matching Program AGENCY: Defense Manpower Data Center, Department of Defense (DoD). ACTION: Notice of a Computer Matching Program. SUMMARY: Subsection (e)(12) of the Privacy Act of 1974, as amended, (5 U.S.C. 552a) requires agencies to publish advance notice of any proposed or revised computer...

77 FR 32085 - Privacy Act of 1974, as Amended; Renewal of Computer Matching Program Between the U.S. Department...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-31

... Matching and Privacy Protection Act of 1988 (Pub. L. 100-503) and the Computer Matching and Privacy... DEPARTMENT OF EDUCATION Privacy Act of 1974, as Amended; Renewal of Computer Matching Program.... ACTION: Notice. SUMMARY: This document provides notice of the renewal of the computer matching program...

A Study of the Programming Languages Used in Information Systems and in Computer Science Curricula

ERIC Educational Resources Information Center

Russell, Jack; Russell, Barbara; Pollacia, Lissa F.; Tastle, William J.

2010-01-01

This paper researches the computer languages taught in the first, second and third programming courses in Computer Information Systems (CIS), Management Information Systems (MIS or IS) curricula as well as in Computer Science (CS) and Information Technology (IT) curricula. Instructors teaching the first course in programming within a four year…

76 FR 77811 - Privacy Act of 1974; Notice of a Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-14

...; Notice of a Computer Matching Program AGENCY: Defense Manpower Data Center, Department of Defense (DoD). ACTION: Notice of a Computer Matching Program. SUMMARY: Subsection (e)(12) of the Privacy Act of 1974, as amended, (5 U.S.C. 552a) requires agencies to publish advance notice of any proposed or revised computer...

Computer program for the IBM personal computer which searches for approximate matches to short oligonucleotide sequences in long target DNA sequences.

PubMed Central

Myers, E W; Mount, D W

1986-01-01

We describe a program which may be used to find approximate matches to a short predefined DNA sequence in a larger target DNA sequence. The program predicts the usefulness of specific DNA probes and sequencing primers and finds nearly identical sequences that might represent the same regulatory signal. The program is written in the C programming language and will run on virtually any computer system with a C compiler, such as the IBM/PC and other computers running under the MS/DOS and UNIX operating systems. The program has been integrated into an existing software package for the IBM personal computer (see article by Mount and Conrad, this volume). Some examples of its use are given. PMID:3753785

76 FR 41234 - Advanced Scientific Computing Advisory Committee Charter Renewal

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-13

... Secretariat, General Services Administration, notice is hereby given that the Advanced Scientific Computing... advice and recommendations concerning the Advanced Scientific Computing program in response only to... Advanced Scientific Computing Research program and recommendations based thereon; --Advice on the computing...

Implementation of a computer database testing and analysis program.

PubMed

Rouse, Deborah P

2007-01-01

The author is the coordinator of a computer software database testing and analysis program implemented in an associate degree nursing program. Computer software database programs help support the testing development and analysis process. Critical thinking is measurable and promoted with their use. The reader of this article will learn what is involved in procuring and implementing a computer database testing and analysis program in an academic nursing program. The use of the computerized database for testing and analysis will be approached as a method to promote and evaluate the nursing student's critical thinking skills and to prepare the nursing student for the National Council Licensure Examination.

Computer simulation of space station computer steered high gain antenna

NASA Technical Reports Server (NTRS)

Beach, S. W.

1973-01-01

The mathematical modeling and programming of a complete simulation program for a space station computer-steered high gain antenna are described. The program provides for reading input data cards, numerically integrating up to 50 first order differential equations, and monitoring up to 48 variables on printed output and on plots. The program system consists of a high gain antenna, an antenna gimbal control system, an on board computer, and the environment in which all are to operate.

Shuttle user analysis (study 2.2): Volume 3. Business Risk And Value of Operations in space (BRAVO). Part 4: Computer programs and data look-up

NASA Technical Reports Server (NTRS)

1974-01-01

Computer program listings as well as graphical and tabulated data needed by the analyst to perform a BRAVO analysis were examined. Graphical aid which can be used to determine the earth coverage of satellites in synchronous equatorial orbits was described. A listing for satellite synthesis computer program as well as a sample printout for the DSCS-11 satellite program and a listing of the symbols used in the program were included. The APL language listing for the payload program cost estimating computer program was given. This language is compatible with many of the time sharing remote terminals computers used in the United States. Data on the intelsat communications network was studied. Costs for telecommunications systems leasing, line of sight microwave relay communications systems, submarine telephone cables, and terrestrial power generation systems were also described.

76 FR 49753 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-11

... Defense. DHA 14 System name: Computer/Electronics Accommodations Program for People with Disabilities... with ``Computer/Electronic Accommodations Program.'' System location: Delete entry and replace with ``Computer/Electronic Accommodations Program, Skyline 5, Suite 302, 5111 Leesburg Pike, Falls Church, VA...

Computers and the Multiplicity of Polynomial Roots.

ERIC Educational Resources Information Center

Wavrik, John J.

1982-01-01

Described are stages in the development of a computer program to solve a particular algebra problem and the nature of algebraic computation is presented. A program in BASIC is provided to give ideas to others for developing their own programs. (MP)

Computer Program To Transliterate Into Arabic

NASA Technical Reports Server (NTRS)

Stephan, E.

1986-01-01

Conceptual program for TRS-80, Model 12 (or equivalent) computer transliterates from English letters of computer keyboard to Arabic characters in output of associated printer. Program automatically changes character sequence from left-to-right of English to right-to-left of Arabic.

Evolving binary classifiers through parallel computation of multiple fitness cases.

PubMed

Cagnoni, Stefano; Bergenti, Federico; Mordonini, Monica; Adorni, Giovanni

2005-06-01

This paper describes two versions of a novel approach to developing binary classifiers, based on two evolutionary computation paradigms: cellular programming and genetic programming. Such an approach achieves high computation efficiency both during evolution and at runtime. Evolution speed is optimized by allowing multiple solutions to be computed in parallel. Runtime performance is optimized explicitly using parallel computation in the case of cellular programming or implicitly taking advantage of the intrinsic parallelism of bitwise operators on standard sequential architectures in the case of genetic programming. The approach was tested on a digit recognition problem and compared with a reference classifier.

SSME structural computer program development. Volume 2: BOPACE users manual

NASA Technical Reports Server (NTRS)

Vos, R. G.

1973-01-01

A computer program for use with a thermal-elastic-plastic-creep structural analyzer is presented. The following functions of the computer program are discussed: (1) analysis of very high temperature and large plastic-creep effects, (2) treatment of cyclic thermal and mechanical loads, (3) development of constitutive theory which closely follows actual behavior under variable temperature conditions, (4) stable numerical solution approach which avoids cumulative errors, and (5) capability of handling up to 1000 degrees of freedom. The computer program is written in FORTRAN IV and has been run on the IBM 360 and UNIVAC 1108 computer systems.

An automated procedure for developing hybrid computer simulations of turbofan engines

NASA Technical Reports Server (NTRS)

Szuch, J. R.; Krosel, S. M.

1980-01-01

A systematic, computer-aided, self-documenting methodology for developing hybrid computer simulations of turbofan engines is presented. The methodology makes use of a host program that can run on a large digital computer and a machine-dependent target (hybrid) program. The host program performs all of the calculations and date manipulations needed to transform user-supplied engine design information to a form suitable for the hybrid computer. The host program also trims the self contained engine model to match specified design point information. A test case is described and comparisons between hybrid simulation and specified engine performance data are presented.

Evolution of a standard microprocessor-based space computer

NASA Technical Reports Server (NTRS)

Fernandez, M.

1980-01-01

An existing in inventory computer hardware/software package (B-1 RFS/ECM) was repackaged and applied to multiple missile/space programs. Concurrent with the application efforts, low risk modifications were made to the computer from program to program to take advantage of newer, advanced technology and to meet increasingly more demanding requirements (computational and memory capabilities, longer life, and fault tolerant autonomy). It is concluded that microprocessors hold promise in a number of critical areas for future space computer applications. However, the benefits of the DoD VHSIC Program are required and the old proliferation problem must be revised.

Parallel and serial computing tools for testing single-locus and epistatic SNP effects of quantitative traits in genome-wide association studies

PubMed Central

Ma, Li; Runesha, H Birali; Dvorkin, Daniel; Garbe, John R; Da, Yang

2008-01-01

Background Genome-wide association studies (GWAS) using single nucleotide polymorphism (SNP) markers provide opportunities to detect epistatic SNPs associated with quantitative traits and to detect the exact mode of an epistasis effect. Computational difficulty is the main bottleneck for epistasis testing in large scale GWAS. Results The EPISNPmpi and EPISNP computer programs were developed for testing single-locus and epistatic SNP effects on quantitative traits in GWAS, including tests of three single-locus effects for each SNP (SNP genotypic effect, additive and dominance effects) and five epistasis effects for each pair of SNPs (two-locus interaction, additive × additive, additive × dominance, dominance × additive, and dominance × dominance) based on the extended Kempthorne model. EPISNPmpi is the parallel computing program for epistasis testing in large scale GWAS and achieved excellent scalability for large scale analysis and portability for various parallel computing platforms. EPISNP is the serial computing program based on the EPISNPmpi code for epistasis testing in small scale GWAS using commonly available operating systems and computer hardware. Three serial computing utility programs were developed for graphical viewing of test results and epistasis networks, and for estimating CPU time and disk space requirements. Conclusion The EPISNPmpi parallel computing program provides an effective computing tool for epistasis testing in large scale GWAS, and the epiSNP serial computing programs are convenient tools for epistasis analysis in small scale GWAS using commonly available computer hardware. PMID:18644146

Experiences with Efficient Methodologies for Teaching Computer Programming to Geoscientists

ERIC Educational Resources Information Center

Jacobs, Christian T.; Gorman, Gerard J.; Rees, Huw E.; Craig, Lorraine E.

2016-01-01

Computer programming was once thought of as a skill required only by professional software developers. But today, given the ubiquitous nature of computation and data science it is quickly becoming necessary for all scientists and engineers to have at least a basic knowledge of how to program. Teaching how to program, particularly to those students…

Computer programs for calculating two-dimensional potential flow through deflected nozzles

NASA Technical Reports Server (NTRS)

Hawk, J. D.; Stockman, N. O.

1979-01-01

Computer programs to calculate the incompressible potential flow, corrected for compressibility, in two-dimensional nozzles at arbitrary operating conditions are presented. A statement of the problem to be solved, a description of each of the computer programs, and sufficient documentation, including a test case, to enable a user to run the program are included.

Exploring Poetry through Interactive Computer Programs.

ERIC Educational Resources Information Center

Nimchinsky, Howard; Camp, Jocelyn

The goal of a project was to design, test, and evaluate several computer programs that allow students in introductory literature and poetry courses to explore a poem in detail and, through a dialogue with the program, to develop their own interpretation of it. Computer programs were completed on poems by Robert Frost and W.H. Auden. Both programs…

Pre-Service Teachers' Uses of and Barriers from Adopting Computer-Assisted Language Learning (CALL) Programs

ERIC Educational Resources Information Center

Samani, Ebrahim; Baki, Roselan; Razali, Abu Bakar

2014-01-01

Success in implementation of computer-assisted language learning (CALL) programs depends on the teachers' understanding of the roles of CALL programs in education. Consequently, it is also important to understand the barriers teachers face in the use of computer-assisted language learning (CALL) programs. The current study was conducted on 14…

A Two-Tier Test-Based Approach to Improving Students' Computer-Programming Skills in a Web-Based Learning Environment

ERIC Educational Resources Information Center

Yang, Tzu-Chi; Hwang, Gwo-Jen; Yang, Stephen J. H.; Hwang, Gwo-Haur

2015-01-01

Computer programming is an important skill for engineering and computer science students. However, teaching and learning programming concepts and skills has been recognized as a great challenge to both teachers and students. Therefore, the development of effective learning strategies and environments for programming courses has become an important…

Influence matrix program for aerodynamic lifting surface theory. [in subsonic flows

NASA Technical Reports Server (NTRS)

Medan, R. T.; Ray, K. S.

1973-01-01

A users manual is described for a USA FORTRAN 4 computer program which computes an aerodynamic influence matrix and is one of several computer programs used to analyze lifting, thin wings in steady, subsonic flow according to a kernel function method lifting surface theory. The most significant features of the program are that it can treat unsymmetrical wings, control points can be placed on the leading and/or trailing edges, and a stable, efficient algorithm is used to compute the influence matrix.

Design of microstrip components by computer

NASA Technical Reports Server (NTRS)

Cisco, T. C.

1972-01-01

A number of computer programs are presented for use in the synthesis of microwave components in microstrip geometries. The programs compute the electrical and dimensional parameters required to synthesize couplers, filters, circulators, transformers, power splitters, diode switches, multipliers, diode attenuators and phase shifters. Additional programs are included to analyze and optimize cascaded transmission lines and lumped element networks, to analyze and synthesize Chebyshev and Butterworth filter prototypes, and to compute mixer intermodulation products. The programs are written in FORTRAN and the emphasis of the study is placed on the use of these programs and not on the theoretical aspects of the structures.

Operational procedure for computer program for design point characteristics of a gas generator or a turbojet lift engine for V/STOL applications

NASA Technical Reports Server (NTRS)

Krebs, R. P.

1972-01-01

The computer program described calculates the design-point characteristics of a gas generator or a turbojet lift engine for V/STOL applications. The program computes the dimensions and mass, as well as the thermodynamic performance of the model engine and its components. The program was written in FORTRAN 4 language. Provision has been made so that the program accepts input values in either SI Units or U.S. Customary Units. Each engine design-point calculation requires less than 0.5 second of 7094 computer time.

a Recursive Approach to Compute Normal Forms

NASA Astrophysics Data System (ADS)

HSU, L.; MIN, L. J.; FAVRETTO, L.

2001-06-01

Normal forms are instrumental in the analysis of dynamical systems described by ordinary differential equations, particularly when singularities close to a bifurcation are to be characterized. However, the computation of a normal form up to an arbitrary order is numerically hard. This paper focuses on the computer programming of some recursive formulas developed earlier to compute higher order normal forms. A computer program to reduce the system to its normal form on a center manifold is developed using the Maple symbolic language. However, it should be stressed that the program relies essentially on recursive numerical computations, while symbolic calculations are used only for minor tasks. Some strategies are proposed to save computation time. Examples are presented to illustrate the application of the program to obtain high order normalization or to handle systems with large dimension.

When technology became language: the origins of the linguistic conception of computer programming, 1950-1960.

PubMed

Nofre, David; Priestley, Mark; Alberts, Gerard

2014-01-01

Language is one of the central metaphors around which the discipline of computer science has been built. The language metaphor entered modern computing as part of a cybernetic discourse, but during the second half of the 1950s acquired a more abstract meaning, closely related to the formal languages of logic and linguistics. The article argues that this transformation was related to the appearance of the commercial computer in the mid-1950s. Managers of computing installations and specialists on computer programming in academic computer centers, confronted with an increasing variety of machines, called for the creation of "common" or "universal languages" to enable the migration of computer code from machine to machine. Finally, the article shows how the idea of a universal language was a decisive step in the emergence of programming languages, in the recognition of computer programming as a proper field of knowledge, and eventually in the way we think of the computer.

Computer Integrated Manufacturing. Florida Vocational Program Guide.

ERIC Educational Resources Information Center

University of South Florida, Tampa. Dept. of Adult and Vocational Education.

This packet contains a program guide and Career Merit Achievement Plan (Career MAP) for the implementation of a computer-integrated manufacturing program in Florida secondary and postsecondary schools. The program guide describes the program content and structure, provides a program description, lists job titles under the program, and includes a…

Computer Engineering Technology. Florida Vocational Program Guide.

ERIC Educational Resources Information Center

University of South Florida, Tampa. Dept. of Adult and Vocational Education.

This packet contains a program guide and Career Merit Achievement Plan (Career MAP) for the implementation of a computer engineering technology program in Florida secondary and postsecondary schools. The program guide describes the program content and structure, provides a program description, lists job titles under the program, and includes a…

Computer-aided programming for message-passing system; Problems and a solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, M.Y.; Gajski, D.D.

1989-12-01

As the number of processors and the complexity of problems to be solved increase, programming multiprocessing systems becomes more difficult and error-prone. Program development tools are necessary since programmers are not able to develop complex parallel programs efficiently. Parallel models of computation, parallelization problems, and tools for computer-aided programming (CAP) are discussed. As an example, a CAP tool that performs scheduling and inserts communication primitives automatically is described. It also generates the performance estimates and other program quality measures to help programmers in improving their algorithms and programs.

Thermochemical cycle analysis using linked CECS72 and HYDRGN computer programs

NASA Technical Reports Server (NTRS)

Donovan, L. F.

1977-01-01

A combined thermochemical cycle analysis computer program was designed. Input to the combined program is the same as input to the thermochemical cycle analysis program except that the extent of the reactions need not be specified. The combined program is designed to be run interactively from a computer time-sharing terminal. This mode of operation allows correction or modification of the cycle to take place during cycle analysis. A group of 13 thermochemical cycles was used to test the combined program.

Optical Design Using Small Dedicated Computers

NASA Astrophysics Data System (ADS)

Sinclair, Douglas C.

1980-09-01

Since the time of the 1975 International Lens Design Conference, we have developed a series of optical design programs for Hewlett-Packard desktop computers. The latest programs in the series, OSLO-25G and OSLO-45G, have most of the capabilities of general-purpose optical design programs, including optimization based on exact ray-trace data. The computational techniques used in the programs are similar to ones used in other programs, but the creative environment experienced by a designer working directly with these small dedicated systems is typically much different from that obtained with shared-computer systems. Some of the differences are due to the psychological factors associated with using a system having zero running cost, while others are due to the design of the program, which emphasizes graphical output and ease of use, as opposed to computational speed.

A computer program for calculation of approximate embryo/fetus radiation dose in nuclear medicine applications.

PubMed

Bayram, Tuncay; Sönmez, Bircan

2012-04-01

In this study, we aimed to make a computer program that calculates approximate radiation dose received by embryo/fetus in nuclear medicine applications. Radiation dose values per MBq-1 received by embryo/fetus in nuclear medicine applications were gathered from literature for various stages of pregnancy. These values were embedded in the computer code, which was written in Fortran 90 program language. The computer program called nmfdose covers almost all radiopharmaceuticals used in nuclear medicine applications. Approximate radiation dose received by embryo/fetus can be calculated easily at a few steps using this computer program. Although there are some constraints on using the program for some special cases, nmfdose is useful and it provides practical solution for calculation of approximate dose to embryo/fetus in nuclear medicine applications. None declared.

Gender and stereotypes in motivation to study computer programming for careers in multimedia

NASA Astrophysics Data System (ADS)

Doubé, Wendy; Lang, Catherine

2012-03-01

A multimedia university programme with relatively equal numbers of male and female students in elective programming subjects provided a rare opportunity to investigate female motivation to study and pursue computer programming in a career. The MSLQ was used to survey 85 participants. In common with research into deterrence of females from STEM domains, females displayed significantly lower self-efficacy and expectancy for success. In contrast to research into deterrence of females from STEM domains, both genders placed similar high values on computer programming and shared high extrinsic and intrinsic goal orientation. The authors propose that the stereotype associated with a creative multimedia career could attract female participation in computer programming whereas the stereotype associated with computer science could be a deterrent.

A review of small canned computer programs for survey research and demographic analysis.

PubMed

Sinquefield, J C

1976-12-01

A variety of small canned computer programs for survey research and demographic analysis appropriate for use in developing countries are reviewed in this article. The programs discussed are SPSS (Statistical Package for the Social Sciences); CENTS, CO-CENTS, CENTS-AID, CENTS-AIE II; MINI-TAB EDIT, FREQUENCIES, TABLES, REGRESSION, CLIENT RECORD, DATES, MULT, LIFE, and PREGNANCY HISTORY; FIVFIV and SINSIN; DCL (Demographic Computer Library); MINI-TAB Population Projection, Functional Population Projection, and Family Planning Target Projection. A description and evaluation for each program of uses, instruction manuals, computer requirements, and procedures for obtaining manuals and programs are provided. Such information is intended to facilitate and encourage the use of the computer by data processors in developing countries.

A DNA sequence analysis package for the IBM personal computer.

PubMed Central

Lagrimini, L M; Brentano, S T; Donelson, J E

1984-01-01

We present here a collection of DNA sequence analysis programs, called "PC Sequence" (PCS), which are designed to run on the IBM Personal Computer (PC). These programs are written in IBM PC compiled BASIC and take full advantage of the IBM PC's speed, error handling, and graphics capabilities. For a modest initial expense in hardware any laboratory can use these programs to quickly perform computer analysis on DNA sequences. They are written with the novice user in mind and require very little training or previous experience with computers. Also provided are a text editing program for creating and modifying DNA sequence files and a communications program which enables the PC to communicate with and collect information from mainframe computers and DNA sequence databases. PMID:6546433

Catalog of Computer Programs Used in Undergraduate Geological Education.

ERIC Educational Resources Information Center

Burger, H. Robert

1983-01-01

Provides list of mineralogy, petrology, and geochemistry computer programs. Each entry includes a brief description, program name and language, availability of program listing, and source and/or reference. (JN)

Exploring Pair Programming Benefits for MIS Majors

ERIC Educational Resources Information Center

Dongo, Tendai; Reed, April H.; O'Hara, Margaret

2016-01-01

Pair programming is a collaborative programming practice that places participants in dyads, working in tandem at one computer to complete programming assignments. Pair programming studies with Computer Science (CS) and Software Engineering (SE) majors have identified benefits such as technical productivity, program/design quality, academic…

SURE reliability analysis: Program and mathematics

NASA Technical Reports Server (NTRS)

Butler, Ricky W.; White, Allan L.

1988-01-01

The SURE program is a new reliability analysis tool for ultrareliable computer system architectures. The computational methods on which the program is based provide an efficient means for computing accurate upper and lower bounds for the death state probabilities of a large class of semi-Markov models. Once a semi-Markov model is described using a simple input language, the SURE program automatically computes the upper and lower bounds on the probability of system failure. A parameter of the model can be specified as a variable over a range of values directing the SURE program to perform a sensitivity analysis automatically. This feature, along with the speed of the program, makes it especially useful as a design tool.

Survey: Computer Usage in Design Courses.

ERIC Educational Resources Information Center

Henley, Ernest J.

1983-01-01

Presents results of a survey of chemical engineering departments regarding computer usage in senior design courses. Results are categorized according to: computer usage (use of process simulators, student-written programs, faculty-written or "canned" programs; costs (hard and soft money); and available software. Programs offered are…

Computer-Based Educational Software System. Final Report.

ERIC Educational Resources Information Center

Brandt, Richard C.; Davis, Bradley N.

CBESS (Computer-Based Educational Software System) is a set of 22 programs addressing authoring, instructional delivery, and instructional management. The programs are divided into five groups: (1) Computer-Based Memorization System (CBMS), which helps students acquire and maintain declarative (factual) knowledge (11 programs); (2) Language Skills…

Frequency Domain Computer Programs for Prediction and Analysis of Rail Vehicle Dynamics : Volume 1. Technical Report

DOT National Transportation Integrated Search

1975-12-01

Frequency domain computer programs developed or acquired by TSC for the analysis of rail vehicle dynamics are described in two volumes. Volume I defines the general analytical capabilities required for computer programs applicable to single rail vehi...

78 FR 15734 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-12

... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary [Docket No. DHS-2013-0010] Privacy Act of 1974; Computer Matching Program AGENCY: Department of Homeland Security/U.S. Citizenship and... computer matching program between the Department of Homeland Security/U.S. Citizenship and Immigration...

78 FR 15733 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-12

... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary [Docket No. DHS-2013-0008] Privacy Act of 1974; Computer Matching Program AGENCY: Department of Homeland Security/U.S. Citizenship and... computer matching program between the Department of Homeland Security/U.S. Citizenship and Immigration...

78 FR 15731 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-12

... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary [Docket No. DHS-2013-0011] Privacy Act of 1974; Computer Matching Program AGENCY: Department of Homeland Security/U.S. Citizenship and Immigration Services. ACTION: Notice. Overview Information: Privacy Act of 1974; Computer Matching Program...

78 FR 15732 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-12

... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary [Docket No. DHS-2013-0007] Privacy Act of 1974; Computer Matching Program AGENCY: Department of Homeland Security/U.S. Citizenship and Immigration Services. ACTION: Notice. Overview Information: Privacy Act of 1974; Computer Matching Program...

78 FR 32711 - Privacy Act of 1974: Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-31

... DEPARTMENT OF VETERANS AFFAIRS Privacy Act of 1974: Computer Matching Program AGENCY: Department of Veterans Affairs. ACTION: Notice. SUMMARY: The Department of Veterans Affairs (VA) provides notice that it intends to conduct a recurring computer-matching program matching Internal Revenue Service (IRS...

Computer Integrated Manufacturing Programs in Higher Education.

ERIC Educational Resources Information Center

International Business Machines Corp., Milford, CT. Academic Information Systems.

This publication focuses on computer integrated manufacturing (CIM) programs at several higher education institutions which teach the use of computing in manufacturing. The document describes programs at the following institutions: University of Alabama (where researchers are investigating CIM techniques with a key focus on transferring their…

Advanced Simulation & Computing FY15 Implementation Plan Volume 2, Rev. 0.5

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCoy, Michel; Archer, Bill; Matzen, M. Keith

2014-09-16

The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the surety and reliability of the U.S. nuclear stockpile. The SSP uses nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of experimental facilities and programs, and the computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities andmore » computational resources that support annual stockpile assessment and certification, study advanced nuclear weapons design and manufacturing processes, analyze accident scenarios and weapons aging, and provide the tools to enable stockpile Life Extension Programs (LEPs) and the resolution of Significant Finding Investigations (SFIs). This requires a balance of resource, including technical staff, hardware, simulation software, and computer science solutions. As the program approaches the end of its second decade, ASC is intently focused on increasing predictive capabilities in a three-dimensional (3D) simulation environment while maintaining support to the SSP. The program continues to improve its unique tools for solving progressively more difficult stockpile problems (sufficient resolution, dimensionality, and scientific details), quantify critical margins and uncertainties, and resolve increasingly difficult analyses needed for the SSP. Where possible, the program also enables the use of high-performance simulation and computing tools to address broader national security needs, such as foreign nuclear weapon assessments and counternuclear terrorism.« less

The Effect of In-Service Training of Computer Science Teachers on Scratch Programming Language Skills Using an Electronic Learning Platform on Programming Skills and the Attitudes towards Teaching Programming

ERIC Educational Resources Information Center

Alkaria, Ahmed; Alhassan, Riyadh

2017-01-01

This study was conducted to examine the effect of in-service training of computer science teachers in Scratch language using an electronic learning platform on acquiring programming skills and attitudes towards teaching programming. The sample of this study consisted of 40 middle school computer science teachers. They were assigned into two…

Computer programs to assist in high resolution thermal denaturation and circular dichroism studies on nucleic acids

PubMed Central

Goodman, Thomas C.; Hardies, Stephen C.; Cortez, Carlos; Hillen, Wolfgang

1981-01-01

Computer programs are described that direct the collection, processing, and graphical display of numerical data obtained from high resolution thermal denaturation (1-3) and circular dichroism (4) studies. Besides these specific applications, the programs may also be useful, either directly or as programming models, in other types of spectrophotometric studies employing computers, programming languages, or instruments similar to those described here (see Materials and Methods). PMID:7335498

Method of fan sound mode structure determination computer program user's manual: Microphone location program

NASA Technical Reports Server (NTRS)

Pickett, G. F.; Wells, R. A.; Love, R. A.

1977-01-01

A computer user's manual describing the operation and the essential features of the microphone location program is presented. The Microphone Location Program determines microphone locations that ensure accurate and stable results from the equation system used to calculate modal structures. As part of the computational procedure for the Microphone Location Program, a first-order measure of the stability of the equation system was indicated by a matrix 'conditioning' number.

Using the TouchMath Program to Teach Mathematical Computation to At-Risk Students and Students with Disabilities

ERIC Educational Resources Information Center

Ellingsen, Ryleigh; Clinton, Elias

2017-01-01

This manuscript reviews the empirical literature of the TouchMath© instructional program. The TouchMath© program is a commercial mathematics series that uses a dot notation system to provide multisensory instruction of computation skills. Using the program, students are taught to solve computational tasks in a multisensory manner that does not…

Case Study: Creation of a Degree Program in Computer Security. White Paper.

ERIC Educational Resources Information Center

Belon, Barbara; Wright, Marie

This paper reports on research into the field of computer security, and undergraduate degrees offered in that field. Research described in the paper reveals only one computer security program at the associate's degree level in the entire country. That program, at Texas State Technical College in Waco, is a 71-credit-hour program leading to an…

Principals and Computers: Getting Started Together. Special Report: Computers in the Schools.

ERIC Educational Resources Information Center

Holland, Lori; Rude-Parkins, Carolyn

1986-01-01

Outlines five lessons learned at Roosevelt-Perry Elementary School (Kentucky) when the computer education program, Humana Computer Tutor project, was implemented. The principal was important to the success of the program. (MD)

75 FR 39575 - Privacy Act of 1974; Notice of a Computer Matching Program Between the Department of Housing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-09

... of a Computer Matching Program Between the Department of Housing and Urban Development (HUD) and the.... ACTION: Notice of a computer matching program between the HUD and the USDA. SUMMARY: In accordance with the Privacy Act of 1974 (5 U.S.C. 552a), as amended by the Computer Matching and Privacy Protection...

76 FR 39119 - Privacy Act of 1974; Notice of a Computer Matching Program Between the Department of Housing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-05

... of a Computer Matching Program Between the Department of Housing and Urban Development (HUD) and the...: Notice of a computer matching program between the HUD and ED. SUMMARY: In accordance with the Privacy Act of 1974 (5 U.S.C. 552a), as amended by the Computer Matching and Privacy Protection Act of 1988 (Pub...

75 FR 67755 - Privacy Act of 1974; Notice of a Computer Matching Program Between the Department of Housing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-03

... of a Computer Matching Program Between the Department of Housing and Urban Development (HUD) and the.... ACTION: Notice of a computer matching program between the HUD and the SBA. SUMMARY: In accordance with the Privacy Act of 1974 (5 U.S.C. 552a), as amended by the Computer Matching and Privacy Protection...

Space Ultrareliable Modular Computer (SUMC) instruction simulator

NASA Technical Reports Server (NTRS)

Curran, R. T.

1972-01-01

The design principles, description, functional operation, and recommended expansion and enhancements are presented for the Space Ultrareliable Modular Computer interpretive simulator. Included as appendices are the user's manual, program module descriptions, target instruction descriptions, simulator source program listing, and a sample program printout. In discussing the design and operation of the simulator, the key problems involving host computer independence and target computer architectural scope are brought into focus.

Computer Science Research Funding: How Much Is Too Little?

DTIC Science & Technology

2009-06-01

Bioinformatics Parallel computing Computational biology Principles of programming Computational neuroscience Real-time and embedded systems Scientific...National Security Agency ( NSA ) • Missile Defense Agency (MDA) and others The various research programs have been coordinated through the DDR&E...DOD funding included only DARPA and OSD programs. FY07 and FY08 PBR funding included DARPA, NSA , some of the Services’ basic and applied research

Computer programs simplify optical system analysis

NASA Technical Reports Server (NTRS)

1965-01-01

The optical ray-trace computer program performs geometrical ray tracing. The energy-trace program calculates the relative monochromatic flux density on a specific target area. This program uses the ray-trace program as a subroutine to generate a representation of the optical system.

Enhancing Instruction through Technology.

ERIC Educational Resources Information Center

Greenleaf, Connie; Gee, Mary Kay

Following an introductory section that provides a rationale for using computers in workplace literacy classes, this guide reviews six computer programs and provides activities that teachers can use with the programs in teaching workplace literacy classes. The six computer programs reviewed are as follows: "Grammar Games,""Spell It 3,""The Way…

Computer-Generated Phase Diagrams for Binary Mixtures.

ERIC Educational Resources Information Center

Jolls, Kenneth R.; And Others

1983-01-01

Computer programs that generate projections of thermodynamic phase surfaces through computer graphics were used to produce diagrams representing properties of water and steam and the pressure-volume-temperature behavior of most of the common equations of state. The program, program options emphasizing thermodynamic features of interest, and…

78 FR 38724 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-27

... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary [Docket No. DHS-2013-0006] Privacy Act of 1974; Computer Matching Program AGENCY: Department of Homeland Security/U.S. Citizenship and... Agreement that establishes a computer matching program between the Department of Homeland Security/U.S...

Undergraduate computational physics projects on quantum computing

NASA Astrophysics Data System (ADS)

Candela, D.

2015-08-01

Computational projects on quantum computing suitable for students in a junior-level quantum mechanics course are described. In these projects students write their own programs to simulate quantum computers. Knowledge is assumed of introductory quantum mechanics through the properties of spin 1/2. Initial, more easily programmed projects treat the basics of quantum computation, quantum gates, and Grover's quantum search algorithm. These are followed by more advanced projects to increase the number of qubits and implement Shor's quantum factoring algorithm. The projects can be run on a typical laptop or desktop computer, using most programming languages. Supplementing resources available elsewhere, the projects are presented here in a self-contained format especially suitable for a short computational module for physics students.

Computer sciences

NASA Technical Reports Server (NTRS)

Smith, Paul H.

1988-01-01

The Computer Science Program provides advanced concepts, techniques, system architectures, algorithms, and software for both space and aeronautics information sciences and computer systems. The overall goal is to provide the technical foundation within NASA for the advancement of computing technology in aerospace applications. The research program is improving the state of knowledge of fundamental aerospace computing principles and advancing computing technology in space applications such as software engineering and information extraction from data collected by scientific instruments in space. The program includes the development of special algorithms and techniques to exploit the computing power provided by high performance parallel processors and special purpose architectures. Research is being conducted in the fundamentals of data base logic and improvement techniques for producing reliable computing systems.

Adaptation of a program for nonlinear finite element analysis to the CDC STAR 100 computer

NASA Technical Reports Server (NTRS)

Pifko, A. B.; Ogilvie, P. L.

1978-01-01

The conversion of a nonlinear finite element program to the CDC STAR 100 pipeline computer is discussed. The program called DYCAST was developed for the crash simulation of structures. Initial results with the STAR 100 computer indicated that significant gains in computation time are possible for operations on gloval arrays. However, for element level computations that do not lend themselves easily to long vector processing, the STAR 100 was slower than comparable scalar computers. On this basis it is concluded that in order for pipeline computers to impact the economic feasibility of large nonlinear analyses it is absolutely essential that algorithms be devised to improve the efficiency of element level computations.

Student Achievement in Computer Programming: Lecture vs Computer-Aided Instruction

ERIC Educational Resources Information Center

Tsai, San-Yun W.; Pohl, Norval F.

1978-01-01

This paper discusses a study of the differences in student learning achievement, as measured by four different types of common performance evaluation techniques, in a college-level computer programming course under three teaching/learning environments: lecture, computer-aided instruction, and lecture supplemented with computer-aided instruction.…

Using the Computer in Special Vocational Programs. Inservice Activities.

ERIC Educational Resources Information Center

Lane, Kenneth; Ward, Raymond

This inservice manual is intended to assist vocational education teachers in using the techniques of computer-assisted instruction in special vocational education programs. Addressed in the individual units are the following topics: the basic principles of computer-assisted instruction (TRS-80 computers and typing on a computer keyboard); money…

32 CFR 806b.50 - Computer matching.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 6 2013-07-01 2013-07-01 false Computer matching. 806b.50 Section 806b.50... PROGRAM Disclosing Records to Third Parties § 806b.50 Computer matching. Computer matching programs... on forms used in applying for benefits. Coordinate computer matching statements on forms with Air...

32 CFR 806b.50 - Computer matching.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 6 2014-07-01 2014-07-01 false Computer matching. 806b.50 Section 806b.50... PROGRAM Disclosing Records to Third Parties § 806b.50 Computer matching. Computer matching programs... on forms used in applying for benefits. Coordinate computer matching statements on forms with Air...

32 CFR 806b.50 - Computer matching.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 6 2012-07-01 2012-07-01 false Computer matching. 806b.50 Section 806b.50... PROGRAM Disclosing Records to Third Parties § 806b.50 Computer matching. Computer matching programs... on forms used in applying for benefits. Coordinate computer matching statements on forms with Air...

32 CFR 806b.50 - Computer matching.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Computer matching. 806b.50 Section 806b.50... PROGRAM Disclosing Records to Third Parties § 806b.50 Computer matching. Computer matching programs... on forms used in applying for benefits. Coordinate computer matching statements on forms with Air...

32 CFR 806b.50 - Computer matching.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Computer matching. 806b.50 Section 806b.50... PROGRAM Disclosing Records to Third Parties § 806b.50 Computer matching. Computer matching programs... on forms used in applying for benefits. Coordinate computer matching statements on forms with Air...

TCP/IP Interface for the Satellite Orbit Analysis Program (SOAP)

NASA Technical Reports Server (NTRS)

Carnright, Robert; Stodden, David; Coggi, John

2009-01-01

The Transmission Control Protocol/ Internet protocol (TCP/IP) interface for the Satellite Orbit Analysis Program (SOAP) provides the means for the software to establish real-time interfaces with other software. Such interfaces can operate between two programs, either on the same computer or on different computers joined by a network. The SOAP TCP/IP module employs a client/server interface where SOAP is the server and other applications can be clients. Real-time interfaces between software offer a number of advantages over embedding all of the common functionality within a single program. One advantage is that they allow each program to divide the computation labor between processors or computers running the separate applications. Secondly, each program can be allowed to provide its own expertise domain with other programs able to use this expertise.

Bladed-shrouded-disc aeroelastic analyses: Computer program updates in NASTRAN level 17.7

NASA Technical Reports Server (NTRS)

Gallo, A. M.; Elchuri, V.; Skalski, S. C.

1981-01-01

In October 1979, a computer program based on the state-of-the-art compressor and structural technologies applied to bladed-shrouded-disc was developed. The program was more operational in NASTRAN Level 16. The bladed disc computer program was updated for operation in NASTRAN Level 17.7. The supersonic cascade unsteady aerodynamics routine UCAS, delivered as part of the NASTRAN Level 16 program was recorded to improve its execution time. These improvements are presented.

On the writing of programming systems for spacecraft computers.

NASA Technical Reports Server (NTRS)

Mathur, F. P.; Rohr, J. A.

1972-01-01

Consideration of the systems designed to generate programs for the increasingly complex digital computers being used on board unmanned deep-space probes. Such programming systems must accommodate the special-purpose features incorporated in the hardware. The use of higher-level language facilities in the programming system can significantly simplify the task. Computers for Mariner and for the Outer Planets Grand Tour are briefly described, as well as their programming systems. Aspects of the higher level languages are considered.

AQMAN; linear and quadratic programming matrix generator using two-dimensional ground-water flow simulation for aquifer management modeling

USGS Publications Warehouse

Lefkoff, L.J.; Gorelick, S.M.

1987-01-01

A FORTRAN-77 computer program code that helps solve a variety of aquifer management problems involving the control of groundwater hydraulics. It is intended for use with any standard mathematical programming package that uses Mathematical Programming System input format. The computer program creates the input files to be used by the optimization program. These files contain all the hydrologic information and management objectives needed to solve the management problem. Used in conjunction with a mathematical programming code, the computer program identifies the pumping or recharge strategy that achieves a user 's management objective while maintaining groundwater hydraulic conditions within desired limits. The objective may be linear or quadratic, and may involve the minimization of pumping and recharge rates or of variable pumping costs. The problem may contain constraints on groundwater heads, gradients, and velocities for a complex, transient hydrologic system. Linear superposition of solutions to the transient, two-dimensional groundwater flow equation is used by the computer program in conjunction with the response matrix optimization method. A unit stress is applied at each decision well and transient responses at all control locations are computed using a modified version of the U.S. Geological Survey two dimensional aquifer simulation model. The program also computes discounted cost coefficients for the objective function and accounts for transient aquifer conditions. (Author 's abstract)

Computer Programs (Turbomachinery)

NASA Technical Reports Server (NTRS)

1978-01-01

NASA computer programs are extensively used in design of industrial equipment. Available from the Computer Software Management and Information Center (COSMIC) at the University of Georgia, these programs are employed as analysis tools in design, test and development processes, providing savings in time and money. For example, two NASA computer programs are used daily in the design of turbomachinery by Delaval Turbine Division, Trenton, New Jersey. The company uses the NASA splint interpolation routine for analysis of turbine blade vibration and the performance of compressors and condensers. A second program, the NASA print plot routine, analyzes turbine rotor response and produces graphs for project reports. The photos show examples of Delaval test operations in which the computer programs play a part. In the large photo below, a 24-inch turbine blade is undergoing test; in the smaller photo, a steam turbine rotor is being prepared for stress measurements under actual operating conditions; the "spaghetti" is wiring for test instrumentation

Computer aided reliability, availability, and safety modeling for fault-tolerant computer systems with commentary on the HARP program

NASA Technical Reports Server (NTRS)

Shooman, Martin L.

1991-01-01

Many of the most challenging reliability problems of our present decade involve complex distributed systems such as interconnected telephone switching computers, air traffic control centers, aircraft and space vehicles, and local area and wide area computer networks. In addition to the challenge of complexity, modern fault-tolerant computer systems require very high levels of reliability, e.g., avionic computers with MTTF goals of one billion hours. Most analysts find that it is too difficult to model such complex systems without computer aided design programs. In response to this need, NASA has developed a suite of computer aided reliability modeling programs beginning with CARE 3 and including a group of new programs such as: HARP, HARP-PC, Reliability Analysts Workbench (Combination of model solvers SURE, STEM, PAWS, and common front-end model ASSIST), and the Fault Tree Compiler. The HARP program is studied and how well the user can model systems using this program is investigated. One of the important objectives will be to study how user friendly this program is, e.g., how easy it is to model the system, provide the input information, and interpret the results. The experiences of the author and his graduate students who used HARP in two graduate courses are described. Some brief comparisons were made with the ARIES program which the students also used. Theoretical studies of the modeling techniques used in HARP are also included. Of course no answer can be any more accurate than the fidelity of the model, thus an Appendix is included which discusses modeling accuracy. A broad viewpoint is taken and all problems which occurred in the use of HARP are discussed. Such problems include: computer system problems, installation manual problems, user manual problems, program inconsistencies, program limitations, confusing notation, long run times, accuracy problems, etc.

The Historian as Computer Programmer.

ERIC Educational Resources Information Center

Campion, Martin C.

1988-01-01

Discusses two type of computer programs--grade book programs and classroom simulations--and how they are used by teachers. Using instructor-developed programs as examples, Campion describes his experiences as a programer and encourages his fellow historians to investigate the possibility of programing for themselves. (GEA)

Liability for Personal Injury Caused by Defective Medical Computer Programs

PubMed Central

Brannigan, Vincent M.

1980-01-01

Defective medical computer programs can cause personal injury. Financial responsibility for the injury under tort law will turn on several factors: whether the program is a product or a service, what types of defect exist in the product, and who produced the program. The factors involved in making these decisions are complex, but knowledge of the relevant issues can assist computer personnel in avoiding liability.

A Computer Based Education (CBE) Program for Middle School Mathematics Intervention

ERIC Educational Resources Information Center

Gulley, Bill

2009-01-01

A Computer Based Education (CBE) program for intervention mathematics was developed, used, and modified over a period of three years in a computer lab at an Arizona Title I middle school. The program is described along with a rationale for the need, design, and use of such a program. Data was collected in the third year and results of the program…

Preschool Cookbook of Computer Programming Topics

ERIC Educational Resources Information Center

Morgado, Leonel; Cruz, Maria; Kahn, Ken

2010-01-01

A common problem in computer programming use for education in general, not simply as a technical skill, is that children and teachers find themselves constrained by what is possible through limited expertise in computer programming techniques. This is particularly noticeable at the preliterate level, where constructs tend to be limited to…

77 FR 5017 - Agency Information Collection Activities; Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-01

... 30 percent for computer programming, 20 percent for attorney services, 30 percent for skilled... workers, 25 percent for computer programming, and 20 percent for management time. (d) Dispute resolution...), or a total cost of $421,200. \\12\\ The blended rate is 40 percent for computer programming, 10 percent...

Student Performance in Computer-Assisted Instruction in Programming.

ERIC Educational Resources Information Center

Friend, Jamesine E.; And Others

A computer-assisted instructional system to teach college students the computer language, AID (Algebraic Interpretive Dialogue), two control programs, and data collected by the two control programs are described. It was found that although first response errors were often those of AID syntax, such errors were easily corrected. Secondly, while…

Using Problem Solving to Teach a Programming Language.

ERIC Educational Resources Information Center

Milbrandt, George

1995-01-01

Computer studies courses should incorporate as many computer concepts and programming language experiences as possible. A gradual increase in problem difficulty will help the student to understand various computer concepts, and the programming language's syntax and structure. A sidebar provides two examples of how to establish a learning…

Case Studies of Liberal Arts Computer Science Programs

ERIC Educational Resources Information Center

Baldwin, D.; Brady, A.; Danyluk, A.; Adams, J.; Lawrence, A.

2010-01-01

Many undergraduate liberal arts institutions offer computer science majors. This article illustrates how quality computer science programs can be realized in a wide variety of liberal arts settings by describing and contrasting the actual programs at five liberal arts colleges: Williams College, Kalamazoo College, the State University of New York…

Assessment of Examinations in Computer Science Doctoral Education

ERIC Educational Resources Information Center

Straub, Jeremy

2014-01-01

This article surveys the examination requirements for attaining degree candidate (candidacy) status in computer science doctoral programs at all of the computer science doctoral granting institutions in the United States. It presents a framework for program examination requirement categorization, and categorizes these programs by the type or types…

The Outlook for Computer Professions: 1985 Rewrites the Program.

ERIC Educational Resources Information Center

Drake, Larry

1986-01-01

The author states that graduates of junior college programs who learn COBOL will continue to find jobs, but employers will increasingly seek college graduates when filling positions for computer programers and systems analysts. Areas of growth for computer applications (services, military, data communications, and artificial intelligence) are…

BASIC Language Flow Charting Program (BASCHART). Technical Note 3-82.

ERIC Educational Resources Information Center

Johnson, Charles C.; And Others

This document describes BASCHART, a computer aid designed to decipher and automatically flow chart computer program logic; it also provides the computer code necessary for this process. Developed to reduce the labor intensive manual process of producing a flow chart for an undocumented or inadequately documented program, BASCHART will…

Computer Programming Goes Back to School

ERIC Educational Resources Information Center

Kafai, Yasmin B.; Burke, Quinn

2013-01-01

We are witnessing a remarkable comeback of programming. Current initiatives to promote computational thinking and to broaden participation in computing signal a renewed interest to bring programming back into K-12 schools and help develop children as producers and not simply consumers of digital media. This essay explores the re-emergence of…

40 CFR Appendix C to Part 66 - Computer Program

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 16 2012-07-01 2012-07-01 false Computer Program C Appendix C to Part 66 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ASSESSMENT AND COLLECTION OF NONCOMPLIANCE PENALTIES BY EPA Pt. 66, App. C Appendix C to Part 66—Computer...

40 CFR Appendix C to Part 66 - Computer Program

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 16 2014-07-01 2014-07-01 false Computer Program C Appendix C to Part 66 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ASSESSMENT AND COLLECTION OF NONCOMPLIANCE PENALTIES BY EPA Pt. 66, App. C Appendix C to Part 66—Computer...

40 CFR Appendix C to Part 66 - Computer Program

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 16 2013-07-01 2013-07-01 false Computer Program C Appendix C to Part 66 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ASSESSMENT AND COLLECTION OF NONCOMPLIANCE PENALTIES BY EPA Pt. 66, App. C Appendix C to Part 66—Computer...

78 FR 3474 - Privacy Act of 1974; Computer Matching Program Between the Office Of Personnel Management and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-16

... Security benefit information to OPM via direct computer link for the administration of certain programs by... OFFICE OF PERSONNEL MANAGEMENT Privacy Act of 1974; Computer Matching Program Between the Office Of Personnel Management and Social Security Administration AGENCY: Office of Personnel Management...

Correlates of Success in Introductory Programming: A Study with Middle School Students

ERIC Educational Resources Information Center

Qian, Yizhou; Lehman, James D.

2016-01-01

The demand for computing professionals in the workplace has led to increased attention to computer science education, and introductory computer science courses have been introduced at different levels of education. This study investigated the relationship between gender, academic performance in non-programming subjects, and programming learning…

Computer Rehabilitation Training for the Severely Disabled.

ERIC Educational Resources Information Center

Louisiana State Univ., Baton Rouge.

The Computer Rehabilitation Training Program for the Severely Disabled is a job-oriented training program to prepare physically handicapped persons to become computer programmers and analysts. The program is operated by: a nonprofit organization of Baton Rouge-area business people interested in data processing; the Department of Social Services,…

Learning Motivation in E-Learning Facilitated Computer Programming Courses

ERIC Educational Resources Information Center

Law, Kris M. Y.; Lee, Victor C. S.; Yu, Y. T.

2010-01-01

Computer programming skills constitute one of the core competencies that graduates from many disciplines, such as engineering and computer science, are expected to possess. Developing good programming skills typically requires students to do a lot of practice, which cannot sustain unless they are adequately motivated. This paper reports a…

CAPSAS: Computer Assisted Program for the Selection of Appropriate Statistics.

ERIC Educational Resources Information Center

Shermis, Mark D.; Albert, Susan L.

A computer-assisted program has been developed for the selection of statistics or statistical techniques by both students and researchers. Based on Andrews, Klem, Davidson, O'Malley and Rodgers "A Guide for Selecting Statistical Techniques for Analyzing Social Science Data," this FORTRAN-compiled interactive computer program was…

Computer program for assessing the theoretical performance of a three dimensional inlet

NASA Technical Reports Server (NTRS)

Agnone, A. M.; Kung, F.

1972-01-01

A computer program for determining the theoretical performance of a three dimensional inlet is presented. An analysis for determining the capture area, ram force, spillage force, and surface pressure force is presented, along with the necessary computer program. A sample calculation is also included.

40 CFR Appendix C to Part 66 - Computer Program

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Computer Program C Appendix C to Part 66 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ASSESSMENT AND COLLECTION OF NONCOMPLIANCE PENALTIES BY EPA Pt. 66, App. C Appendix C to Part 66—Computer...

Atmospheric transmission computer program CP

NASA Technical Reports Server (NTRS)

Pitts, D. E.; Barnett, T. L.; Korb, C. L.; Hanby, W.; Dillinger, A. E.

1974-01-01

A computer program is described which allows for calculation of the effects of carbon dioxide, water vapor, methane, ozone, carbon monoxide, and nitrous oxide on earth resources remote sensing techniques. A flow chart of the program and operating instructions are provided. Comparisons are made between the atmospheric transmission obtained from laboratory and spacecraft spectrometer data and that obtained from a computer prediction using a model atmosphere and radiosonde data. Limitations of the model atmosphere are discussed. The computer program listings, input card formats, and sample runs for both radiosonde data and laboratory data are included.

Additional development of the XTRAN3S computer program

NASA Technical Reports Server (NTRS)

Borland, C. J.

1989-01-01

Additional developments and enhancements to the XTRAN3S computer program, a code for calculation of steady and unsteady aerodynamics, and associated aeroelastic solutions, for 3-D wings in the transonic flow regime are described. Algorithm improvements for the XTRAN3S program were provided including an implicit finite difference scheme to enhance the allowable time step and vectorization for improved computational efficiency. The code was modified to treat configurations with a fuselage, multiple stores/nacelles/pylons, and winglets. Computer program changes (updates) for error corrections and updates for version control are provided.

A data reduction technique and associated computer program for obtaining vehicle attitudes with a single onboard camera

NASA Technical Reports Server (NTRS)

Bendura, R. J.; Renfroe, P. G.

1974-01-01

A detailed discussion of the application of a previously method to determine vehicle flight attitude using a single camera onboard the vehicle is presented with emphasis on the digital computer program format and data reduction techniques. Application requirements include film and earth-related coordinates of at least two landmarks (or features), location of the flight vehicle with respect to the earth, and camera characteristics. Included in this report are a detailed discussion of the program input and output format, a computer program listing, a discussion of modifications made to the initial method, a step-by-step basic data reduction procedure, and several example applications. The computer program is written in FORTRAN 4 language for the Control Data 6000 series digital computer.

An IBM 370 assembly language program verifier

NASA Technical Reports Server (NTRS)

Maurer, W. D.

1977-01-01

The paper describes a program written in SNOBOL which verifies the correctness of programs written in assembly language for the IBM 360 and 370 series of computers. The motivation for using assembly language as a source language for a program verifier was the realization that many errors in programs are caused by misunderstanding or ignorance of the characteristics of specific computers. The proof of correctness of a program written in assembly language must take these characteristics into account. The program has been compiled and is currently running at the Center for Academic and Administrative Computing of The George Washington University.

Simulating smokers' acceptance of modifications in a cessation program.

PubMed Central

Spoth, R

1992-01-01

Recent research has underscored the importance of assessing barriers to smokers' acceptance of cessation programs. This paper illustrates the use of computer simulations to gauge smokers' response to program modifications which may produce barriers to participation. It also highlights methodological issues encountered in conducting this work. Computer simulations were based on conjoint analysis, a consumer research method which enables measurement of smokers' relative preference for various modifications of cessation programs. Results from two studies are presented in this paper. The primary study used a randomly selected sample of 218 adult smokers who participated in a computer-assisted phone interview. Initially, the study assessed smokers' relative utility rating of 30 features of cessation programs. Utility data were used in computer-simulated comparisons of a low-cost, self-help oriented program under development and five other existing programs. A baseline version of the program under development and two modifications (for example, use of a support group with a higher level of cost) were simulated. Both the baseline version and modifications received a favorable response vis-à-vis comparison programs. Modifications requiring higher program costs were, however, associated with moderately reduced levels of favorable consumer response. The second study used a sample of 70 smokers who responded to an expanded set of smoking cessation program features focusing on program packaging. This secondary study incorporate in-person, computer-assisted interviews at a shopping mall, with smokers viewing an artist's mock-up of various program options on display. A similar pattern of responses to simulated program modifications emerged, with monetary cost apparently playing a key role. The significance of conjoint-based computer simulation as a tool in program development or dissemination, salient methodological issues, and implications for further research are discussed. PMID:1738813

Simulating smokers' acceptance of modifications in a cessation program.

PubMed

Spoth, R

1992-01-01

Recent research has underscored the importance of assessing barriers to smokers' acceptance of cessation programs. This paper illustrates the use of computer simulations to gauge smokers' response to program modifications which may produce barriers to participation. It also highlights methodological issues encountered in conducting this work. Computer simulations were based on conjoint analysis, a consumer research method which enables measurement of smokers' relative preference for various modifications of cessation programs. Results from two studies are presented in this paper. The primary study used a randomly selected sample of 218 adult smokers who participated in a computer-assisted phone interview. Initially, the study assessed smokers' relative utility rating of 30 features of cessation programs. Utility data were used in computer-simulated comparisons of a low-cost, self-help oriented program under development and five other existing programs. A baseline version of the program under development and two modifications (for example, use of a support group with a higher level of cost) were simulated. Both the baseline version and modifications received a favorable response vis-à-vis comparison programs. Modifications requiring higher program costs were, however, associated with moderately reduced levels of favorable consumer response. The second study used a sample of 70 smokers who responded to an expanded set of smoking cessation program features focusing on program packaging. This secondary study incorporate in-person, computer-assisted interviews at a shopping mall, with smokers viewing an artist's mock-up of various program options on display. A similar pattern of responses to simulated program modifications emerged, with monetary cost apparently playing a key role. The significance of conjoint-based computer simulation as a tool in program development or dissemination, salient methodological issues, and implications for further research are discussed.

10 CFR 961.11 - Text of the contract.

Code of Federal Regulations, 2014 CFR

2014-01-01

... program including information on cost projections, project plans and progress reports. 5. (a) Beginning on...-type documents or computer software (including computer programs, computer software data bases, and computer software documentation). Examples of technical data include research and engineering data...

10 CFR 961.11 - Text of the contract.

Code of Federal Regulations, 2013 CFR

2013-01-01

... program including information on cost projections, project plans and progress reports. 5. (a) Beginning on...-type documents or computer software (including computer programs, computer software data bases, and computer software documentation). Examples of technical data include research and engineering data...

Promoting healthy computer use among middle school students: a pilot school-based health promotion program.

PubMed

Ciccarelli, Marina; Portsmouth, Linda; Harris, Courtenay; Jacobs, Karen

2012-01-01

Introduction of notebook computers in many schools has become integral to learning. This has increased students' screen-based exposure and the potential risks to physical and visual health. Unhealthy computing behaviours include frequent and long durations of exposure; awkward postures due to inappropriate furniture and workstation layout, and ignoring computer-related discomfort. Describe the framework for a planned school-based health promotion program to encourage healthy computing behaviours among middle school students. This planned program uses a community- based participatory research approach. Students in Year 7 in 2011 at a co-educational middle school, their parents, and teachers have been recruited. Baseline data was collected on students' knowledge of computer ergonomics, current notebook exposure, and attitudes towards healthy computing behaviours; and teachers' and self-perceived competence to promote healthy notebook use among students, and what education they wanted. The health promotion program is being developed by an inter-professional team in collaboration with students, teachers and parents to embed concepts of ergonomics education in relevant school activities and school culture. End of year changes in reported and observed student computing behaviours will be used to determine the effectiveness of the program. Building a body of evidence regarding physical health benefits to students from this school-based ergonomics program can guide policy development on the healthy use of computers within children's educational environments.

Computational Understanding: Analysis of Sentences and Context

DTIC Science & Technology

1974-05-01

Computer Science Department Stanford, California 9430b 10- PROGRAM ELEMENT. PROJECT. TASK AREA « WORK UNIT NUMBERS II. CONTROLLING OFFICE NAME...these is the need tor programs that can respond in useful ways to information expressed in a natural language. However a computational understanding...buying structure because "Mary" appears where it does. But the time for analysis was rarely over five seconds of computer time, when the Lisp program

GEO3D - Three-Dimensional Computer Model of a Ground Source Heat Pump System

DOE Data Explorer

James Menart

2013-06-07

This file is the setup file for the computer program GEO3D. GEO3D is a computer program written by Jim Menart to simulate vertical wells in conjunction with a heat pump for ground source heat pump (GSHP) systems. This is a very detailed three-dimensional computer model. This program produces detailed heat transfer and temperature field information for a vertical GSHP system.

Grand Challenges 1993: High Performance Computing and Communications. A Report by the Committee on Physical, Mathematical, and Engineering Sciences. The FY 1993 U.S. Research and Development Program.

ERIC Educational Resources Information Center

Office of Science and Technology Policy, Washington, DC.

This report presents the United States research and development program for 1993 for high performance computing and computer communications (HPCC) networks. The first of four chapters presents the program goals and an overview of the federal government's emphasis on high performance computing as an important factor in the nation's scientific and…

The SURE reliability analysis program

NASA Technical Reports Server (NTRS)

Butler, R. W.

1986-01-01

The SURE program is a new reliability tool for ultrareliable computer system architectures. The program is based on computational methods recently developed for the NASA Langley Research Center. These methods provide an efficient means for computing accurate upper and lower bounds for the death state probabilities of a large class of semi-Markov models. Once a semi-Markov model is described using a simple input language, the SURE program automatically computes the upper and lower bounds on the probability of system failure. A parameter of the model can be specified as a variable over a range of values directing the SURE program to perform a sensitivity analysis automatically. This feature, along with the speed of the program, makes it especially useful as a design tool.

The SURE Reliability Analysis Program

NASA Technical Reports Server (NTRS)

Butler, R. W.

1986-01-01

The SURE program is a new reliability analysis tool for ultrareliable computer system architectures. The program is based on computational methods recently developed for the NASA Langley Research Center. These methods provide an efficient means for computing accurate upper and lower bounds for the death state probabilities of a large class of semi-Markov models. Once a semi-Markov model is described using a simple input language, the SURE program automatically computes the upper and lower bounds on the probability of system failure. A parameter of the model can be specified as a variable over a range of values directing the SURE program to perform a sensitivity analysis automatically. This feature, along with the speed of the program, makes it especially useful as a design tool.

The engineering design integration (EDIN) system. [digital computer program complex

NASA Technical Reports Server (NTRS)

Glatt, C. R.; Hirsch, G. N.; Alford, G. E.; Colquitt, W. N.; Reiners, S. J.

1974-01-01

A digital computer program complex for the evaluation of aerospace vehicle preliminary designs is described. The system consists of a Univac 1100 series computer and peripherals using the Exec 8 operating system, a set of demand access terminals of the alphanumeric and graphics types, and a library of independent computer programs. Modification of the partial run streams, data base maintenance and construction, and control of program sequencing are provided by a data manipulation program called the DLG processor. The executive control of library program execution is performed by the Univac Exec 8 operating system through a user established run stream. A combination of demand and batch operations is employed in the evaluation of preliminary designs. Applications accomplished with the EDIN system are described.

Student Use of Physics to Make Sense of Incomplete but Functional VPython Programs in a Lab Setting

NASA Astrophysics Data System (ADS)

Weatherford, Shawn A.

2011-12-01

Computational activities in Matter & Interactions, an introductory calculus-based physics course, have the instructional goal of providing students with the experience of applying the same set of a small number of fundamental principles to model a wide range of physical systems. However there are significant instructional challenges for students to build computer programs under limited time constraints, especially for students who are unfamiliar with programming languages and concepts. Prior attempts at designing effective computational activities were successful at having students ultimately build working VPython programs under the tutelage of experienced teaching assistants in a studio lab setting. A pilot study revealed that students who completed these computational activities had significant difficultly repeating the exact same tasks and further, had difficulty predicting the animation that would be produced by the example program after interpreting the program code. This study explores the interpretation and prediction tasks as part of an instructional sequence where students are asked to read and comprehend a functional, but incomplete program. Rather than asking students to begin their computational tasks with modifying program code, we explicitly ask students to interpret an existing program that is missing key lines of code. The missing lines of code correspond to the algebraic form of fundamental physics principles or the calculation of forces which would exist between analogous physical objects in the natural world. Students are then asked to draw a prediction of what they would see in the simulation produced by the VPython program and ultimately run the program to evaluate the students' prediction. This study specifically looks at how the participants use physics while interpreting the program code and creating a whiteboard prediction. This study also examines how students evaluate their understanding of the program and modification goals at the beginning of the modification task. While working in groups over the course of a semester, study participants were recorded while they completed three activities using these incomplete programs. Analysis of the video data showed that study participants had little difficulty interpreting physics quantities, generating a prediction, or determining how to modify the incomplete program. Participants did not base their prediction solely from the information from the incomplete program. When participants tried to predict the motion of the objects in the simulation, many turned to their knowledge of how the system would evolve if it represented an analogous real-world physical system. For example, participants attributed the real-world behavior of springs to helix objects even though the program did not include calculations for the spring to exert a force when stretched. Participants rarely interpreted lines of code in the computational loop during the first computational activity, but this changed during latter computational activities with most participants using their physics knowledge to interpret the computational loop. Computational activities in the Matter & Interactions curriculum were revised in light of these findings to include an instructional sequence of tasks to build a comprehension of the example program. The modified activities also ask students to create an additional whiteboard prediction for the time-evolution of the real-world phenomena which the example program will eventually model. This thesis shows how comprehension tasks identified by Palinscar and Brown (1984) as effective in improving reading comprehension are also effective in helping students apply their physics knowledge to interpret a computer program which attempts to model a real-world phenomena and identify errors in their understanding of the use, or omission, of fundamental physics principles in a computational model.

Care 3, phase 1, volume 2

NASA Technical Reports Server (NTRS)

Stiffler, J. J.; Bryant, L. A.; Guccione, L.

1979-01-01

A computer program was developed as a general purpose reliability tool for fault tolerant avionics systems. The computer program requirements, together with several appendices containing computer printouts are presented.

Analysis of EnergyPlus for use in residential building energy optimization

NASA Astrophysics Data System (ADS)

Spencer, Justin S.

This work explored the utility of EnergyPlus as a simulation engine for doing residential building energy optimization, with the objective of finding the modeling areas that require further development in EnergyPlus for residential optimization applications. This work was conducted primarily during 2006-2007, with publication occurring later in 2010. The assessments and recommendations apply to the simulation tool versions available in 2007. During this work, an EnergyPlus v2.0 (2007) input file generator was developed for use in BEopt 0.8.0.4 (2007). BEopt 0.8.0.4 is a residential Building Energy optimization program developed at the National Renewable Energy Laboratory in Golden, Colorado. Residential modeling capabilities of EnergyPlus v2.0 were scrutinized and tested. Modeling deficiencies were identified in a number of areas. These deficiencies were compared to deficiencies in the DOE2.2 V44E4(2007)/TRNSYS simulation engines. The highest priority gaps in EnergyPlus v2.0's residential modeling capability are in infiltration, duct leakage, and foundation modeling. Optimization results from DOE2.2 V44E4 and EnergyPlus v2.0 were analyzed to search for modeling differences that have a significant impact on optimization results. Optimal buildings at different energy savings levels were compared to look for biases. It was discovered that the EnergyPlus v2.0 optimizations consistently chose higher wall insulation levels than the DOE2.2 V44E4 optimizations. The points composing the optimal paths chosen by DOE2.2 V44E4 and EnergyPlus v2.0 were compared to look for points chosen by one optimization that were significantly different from the other optimal path. These outliers were compared to consensus optimal points to determine the simulation differences that cause disparities in the optimization results. The differences were primarily caused by modeling of window radiation exchange and HVAC autosizing.

Rocket exhaust plume computer program improvement. Volume 1: Summary: Method of characteristics nozzle and plume programs

NASA Technical Reports Server (NTRS)

Ratliff, A. W.; Smith, S. D.; Penny, N. M.

1972-01-01

A summary is presented of the various documents that discuss and describe the computer programs and analysis techniques which are available for rocket nozzle and exhaust plume calculations. The basic method of characteristics program is discussed, along with such auxiliary programs as the plume impingement program, the plot program and the thermochemical properties program.

GEODYN system support program, volume 4. [computer program for trajectory analysis of artificial satellites

NASA Technical Reports Server (NTRS)

Mullins, N. E.

1972-01-01

The GEODYN Orbit Determination and Geodetic Parameter Estimation System consists of a set of computer programs designed to determine and analyze definitive satellite orbits and their associated geodetic and measurement parameters. This manual describes the Support Programs used by the GEODYN System. The mathematics and programming descriptions are detailed. The operational procedures of each program are presented. GEODYN ancillary analysis programs may be grouped into three different categories: (1) orbit comparison - DELTA (2) data analysis using reference orbits - GEORGE, and (3) pass geometry computations - GROUNDTRACK. All of the above three programs use one or more tapes written by the GEODYN program in either a data reduction or orbit generator run.

Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies report. Volume 3: Computer program listings

NASA Technical Reports Server (NTRS)

1979-01-01

A description and listing is presented of two computer programs: Hybrid Vehicle Design Program (HYVELD) and Hybrid Vehicle Simulation Program (HYVEC). Both of the programs are modifications and extensions of similar programs developed as part of the Electric and Hybrid Vehicle System Research and Development Project.

Fluid dynamics computer programs for NERVA turbopump

NASA Technical Reports Server (NTRS)

Brunner, J. J.

1972-01-01

During the design of the NERVA turbopump, numerous computer programs were developed for the analyses of fluid dynamic problems within the machine. Program descriptions, example cases, users instructions, and listings for the majority of these programs are presented.

Use of the Computer for Research on Instruction and Student Understanding in Physics.

NASA Astrophysics Data System (ADS)

Grayson, Diane Jeanette

This dissertation describes an investigation of how the computer may be utilized to perform research on instruction and on student understanding in physics. The research was conducted within three content areas: kinematics, waves and dynamics. The main focus of the research on instruction was the determination of factors needed for a computer program to be instructionally effective. The emphasis in the research on student understanding was the identification of specific conceptual and reasoning difficulties students encounter with the subject matter. Most of the research was conducted using the computer -based interview, a technique developed during the early part of the work, conducted within the domain of kinematics. In a computer-based interview, a student makes a prediction about how a particular system will behave under given circumstances, observes a simulation of the event on a computer screen, and then is asked by an interviewer to explain any discrepancy between prediction and observation. In the course of the research, a model was developed for producing educational software. The model has three important components: (i) research on student difficulties in the content area to be addressed, (ii) observations of students using the computer program, and (iii) consequent program modification. This model was used to guide the development of an instructional computer program dealing with graphical representations of transverse pulses. Another facet of the research involved the design of a computer program explicitly for the purposes of research. A computer program was written that simulates a modified Atwood's machine. The program was than used in computer -based interviews and proved to be an effective means of probing student understanding of dynamics concepts. In order to ascertain whether or not the student difficulties identified were peculiar to the computer, laboratory-based interviews with real equipment were also conducted. The laboratory-based interviews were designed to parallel the computer-based interviews as closely as possible. The results of both types of interviews are discussed in detail. The dissertation concludes with a discussion of some of the benefits of using the computer in physics instruction and physics education research. Attention is also drawn to some of the limitations of the computer as a research instrument or instructional device.

An Integrated Development Environment for Adiabatic Quantum Programming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Humble, Travis S; McCaskey, Alex; Bennink, Ryan S

2014-01-01

Adiabatic quantum computing is a promising route to the computational power afforded by quantum information processing. The recent availability of adiabatic hardware raises the question of how well quantum programs perform. Benchmarking behavior is challenging since the multiple steps to synthesize an adiabatic quantum program are highly tunable. We present an adiabatic quantum programming environment called JADE that provides control over all the steps taken during program development. JADE captures the workflow needed to rigorously benchmark performance while also allowing a variety of problem types, programming techniques, and processor configurations. We have also integrated JADE with a quantum simulation enginemore » that enables program profiling using numerical calculation. The computational engine supports plug-ins for simulation methodologies tailored to various metrics and computing resources. We present the design, integration, and deployment of JADE and discuss its use for benchmarking adiabatic quantum programs.« less

The Road to Computer Literacy. Part V: Objectives and Activities for Grades 10-12.

ERIC Educational Resources Information Center

Bitter, Gary

1983-01-01

Presents computer-oriented activities in computer awareness and programing for students in grades 10-12. Intended for use by teachers of all disciplines, activities include such topics as prediction, interpretation and generalization of data, computer systems, PASCAL and PILOT programing, sampling techniques, computer survival, invasion of…

38 CFR 21.8074 - Computing the period for vocational training program participation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Computing the period for... Vocational Training § 21.8074 Computing the period for vocational training program participation. (a) Computing the participation period. To compute the number of months and days of an eligible child's...

Benchmark Lisp And Ada Programs

NASA Technical Reports Server (NTRS)

Davis, Gloria; Galant, David; Lim, Raymond; Stutz, John; Gibson, J.; Raghavan, B.; Cheesema, P.; Taylor, W.

1992-01-01

Suite of nonparallel benchmark programs, ELAPSE, designed for three tests: comparing efficiency of computer processing via Lisp vs. Ada; comparing efficiencies of several computers processing via Lisp; or comparing several computers processing via Ada. Tests efficiency which computer executes routines in each language. Available for computer equipped with validated Ada compiler and/or Common Lisp system.

Computer Languages: A Practical Guide to the Chief Programming Languages.

ERIC Educational Resources Information Center

Sanderson, Peter C.

All the most commonly-used high-level computer languages are discussed in this book. An introductory discussion provides an overview of the basic components of a digital computer, the general planning of a computer programing problem, and the various types of computer languages. Each chapter is self-contained, emphasizes those features of a…

Automated procedure for developing hybrid computer simulations of turbofan engines. Part 1: General description

NASA Technical Reports Server (NTRS)

Szuch, J. R.; Krosel, S. M.; Bruton, W. M.

1982-01-01

A systematic, computer-aided, self-documenting methodology for developing hybrid computer simulations of turbofan engines is presented. The methodology that is pesented makes use of a host program that can run on a large digital computer and a machine-dependent target (hybrid) program. The host program performs all the calculations and data manipulations that are needed to transform user-supplied engine design information to a form suitable for the hybrid computer. The host program also trims the self-contained engine model to match specified design-point information. Part I contains a general discussion of the methodology, describes a test case, and presents comparisons between hybrid simulation and specified engine performance data. Part II, a companion document, contains documentation, in the form of computer printouts, for the test case.

A system for the input and storage of data in the Besm-6 digital computer

NASA Technical Reports Server (NTRS)

Schmidt, K.; Blenke, L.

1975-01-01

Computer programs used for the decoding and storage of large volumes of data on the the BESM-6 computer are described. The following factors are discussed: the programming control language allows the programs to be run as part of a modular programming system used in data processing; data control is executed in a hierarchically built file on magnetic tape with sequential index storage; and the programs are not dependent on the structure of the data.

77 FR 38610 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-28

... DEPARTMENT OF EDUCATION Privacy Act of 1974; Computer Matching Program AGENCY: Department of Education. ACTION: Notice--Computer matching agreement between the Department of Education and the Department of Defense. SUMMARY: This document provides notice of the continuation of the computer matching...

Computers in Engineering Teaching.

ERIC Educational Resources Information Center

Rushby, N. J.

This bibliography cites 26 books, papers, and reports dealing with various uses of computers in engineering education; and describes several computer programs available for use in teaching aeronautical, chemical, civil, electrical and electronic, mechanical, and nuclear engineering. Each computer program entry is presented by name, author,…

Influence of direct computer experience on older adults' attitudes toward computers.

PubMed

Jay, G M; Willis, S L

1992-07-01

This research examined whether older adults' attitudes toward computers became more positive as a function of computer experience. The sample comprised 101 community-dwelling older adults aged 57 to 87. The intervention involved a 2-week computer training program in which subjects learned to use a desktop publishing software program. A multidimensional computer attitude measure was used to assess differential attitude change and maintenance of change following training. The results indicated that older adults' computer attitudes are modifiable and that direct computer experience is an effective means of change. Attitude change as a function of training was found for the attitude dimensions targeted by the intervention program: computer comfort and efficacy. In addition, maintenance of attitude change was established for at least two weeks following training.

Improved neutron activation prediction code system development

NASA Technical Reports Server (NTRS)

Saqui, R. M.

1971-01-01

Two integrated neutron activation prediction code systems have been developed by modifying and integrating existing computer programs to perform the necessary computations to determine neutron induced activation gamma ray doses and dose rates in complex geometries. Each of the two systems is comprised of three computational modules. The first program module computes the spatial and energy distribution of the neutron flux from an input source and prepares input data for the second program which performs the reaction rate, decay chain and activation gamma source calculations. A third module then accepts input prepared by the second program to compute the cumulative gamma doses and/or dose rates at specified detector locations in complex, three-dimensional geometries.

RAWINPROC: Computer program for decommutating, interpreting, and interpolating Rawinsonde meteorological balloon sounding data

NASA Technical Reports Server (NTRS)

Staffanson, F. L.

1981-01-01

The FORTRAN computer program RAWINPROC accepts output from NASA Wallops computer program METPASS1; and produces input for NASA computer program 3.0.0700 (ECC-PRD). The three parts together form a software system for the completely automatic reduction of standard RAWINSONDE sounding data. RAWINPROC pre-edits the 0.1-second data, including time-of-day, azimuth, elevation, and sonde-modulated tone frequency, condenses the data according to successive dwells of the tone frequency, decommutates the condensed data into the proper channels (temperature, relative humidity, high and low references), determines the running baroswitch contact number and computes the associated pressure altitudes, and interpolates the data appropriate for input to ACC-PRD.

An adaptive maneuvering logic computer program for the simulation of one-on-one air-to-air combat. Volume 1: General description

NASA Technical Reports Server (NTRS)

Burgin, G. H.; Fogel, L. J.; Phelps, J. P.

1975-01-01

A technique for computer simulation of air combat is described. Volume 1 decribes the computer program and its development in general terms. Two versions of the program exist. Both incorporate a logic for selecting and executing air combat maneuvers with performance models of specific fighter aircraft. In the batch processing version the flight paths of two aircraft engaged in interactive aerial combat and controlled by the same logic are computed. The realtime version permits human pilots to fly air-to-air combat against the adaptive maneuvering logic (AML) in Langley Differential Maneuvering Simulator (DMS). Volume 2 consists of a detailed description of the computer programs.

A tangible programming tool for children to cultivate computational thinking.

PubMed

Wang, Danli; Wang, Tingting; Liu, Zhen

2014-01-01

Game and creation are activities which have good potential for computational thinking skills. In this paper we present T-Maze, an economical tangible programming tool for children aged 5-9 to build computer programs in maze games by placing wooden blocks. Through the use of computer vision technology, T-Maze provides a live programming interface with real-time graphical and voice feedback. We conducted a user study with 7 children using T-Maze to play two levels of maze-escape games and create their own mazes. The results show that T-Maze is not only easy to use, but also has the potential to help children cultivate computational thinking like abstraction, problem decomposition, and creativity.

An experimental and theoretical investigation of deposition patterns from an agricultural airplane

NASA Technical Reports Server (NTRS)

Morris, D. J.; Croom, C. C.; Vandam, C. P.; Holmes, B. J.

1984-01-01

A flight test program has been conducted with a representative agricultural airplane to provide data for validating a computer program model which predicts aerially applied particle deposition. Test procedures and the data from this test are presented and discussed. The computer program features are summarized, and comparisons of predicted and measured particle deposition are presented. Applications of the computer program for spray pattern improvement are illustrated.

Increasing productivity of the McAuto CAD/CAE system by user-specific applications programming

NASA Technical Reports Server (NTRS)

Plotrowski, S. M.; Vu, T. H.

1985-01-01

Significant improvements in the productivity of the McAuto Computer-Aided Design/Computer-Aided Engineering (CAD/CAE) system were achieved by applications programming using the system's own Graphics Interactive Programming language (GRIP) and the interface capabilities with the main computer on which the system resides. The GRIP programs for creating springs, bar charts, finite element model representations and aiding management planning are presented as examples.

Digital optical computers at the optoelectronic computing systems center

NASA Technical Reports Server (NTRS)

Jordan, Harry F.

1991-01-01

The Digital Optical Computing Program within the National Science Foundation Engineering Research Center for Opto-electronic Computing Systems has as its specific goal research on optical computing architectures suitable for use at the highest possible speeds. The program can be targeted toward exploiting the time domain because other programs in the Center are pursuing research on parallel optical systems, exploiting optical interconnection and optical devices and materials. Using a general purpose computing architecture as the focus, we are developing design techniques, tools and architecture for operation at the speed of light limit. Experimental work is being done with the somewhat low speed components currently available but with architectures which will scale up in speed as faster devices are developed. The design algorithms and tools developed for a general purpose, stored program computer are being applied to other systems such as optimally controlled optical communication networks.

COSMIC: A catalog of selected computer programs

NASA Technical Reports Server (NTRS)

1980-01-01

Information is presented on various computer programs developed in the space program which are now available to the public. Many programs from the Department of Defense and selected software from other government agencies are also offered. Over 1500 programs in almost every technical or managerial discipline are available.

Computer Literacy of Turkish Preservice Teachers in Different Teacher Training Programs

ERIC Educational Resources Information Center

Ozsevgec, Tuncay

2011-01-01

This paper reports on an investigation into the sophomore and senior preservice teachers' computer literacy in different teacher training programs and to determine relationship between grades and the teacher training programs in terms of their computer literacy. The study used case study research methodology, and the sample consisted of 276…

A Computer Course for Business Students: Teacher's Guide.

ERIC Educational Resources Information Center

Waterhouse, Ann

This teacher's guide is for a course designed to teach business students the fundamentals of the BASIC language and computer programming using a series of business-oriented programs. Each lesson contains an introduction, flow charts, and computer programs. The six lesson topics are print-out and format control, count-average, withholding tax…

Automated computer grading of hardwood lumber

Treesearch

P. Klinkhachorn; J.P. Franklin; Charles W. McMillin; R.W. Conners; H.A. Huber

1988-01-01

This paper describes an improved computer program to grade hardwood lumber. The program was created as part of a system to automate various aspects of the hardwood manufacturing industry. It enhances previous efforts by considering both faces of the board and provides easy application of species dependent rules. The program can be readily interfaced with a computer...

77 FR 33547 - Privacy Act of 1974, as Amended; Computer Matching Program (SSA/Centers for Medicare and Medicaid...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-06

... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA 2012-0015] Privacy Act of 1974, as Amended; Computer Matching Program (SSA/ Centers for Medicare and Medicaid Services (CMS))--Match Number 1094 AGENCY: Social Security Administration (SSA). ACTION: Notice of a new computer matching program that will expire...

Computer program user's manual for advanced general aviation propeller study

NASA Technical Reports Server (NTRS)

Worobel, R.

1972-01-01

A user's manual is presented for a computer program for predicting the performance (static, flight, and reverse), noise, weight and cost of propellers for advanced general aviation aircraft of the 1980 time period. Complete listings of this computer program with detailed instructions and samples of input and output are included.

Analysis of rocket engine injection combustion processes

NASA Technical Reports Server (NTRS)

Salmon, J. W.; Saltzman, D. H.

1977-01-01

Mixing methodology improvement for the JANNAF DER and CICM injection/combustion analysis computer programs was accomplished. ZOM plane prediction model development was improved for installation into the new standardized DER computer program. An intra-element mixing model developing approach was recommended for gas/liquid coaxial injection elements for possible future incorporation into the CICM computer program.

Developing Computer Programming Concepts and Skills via Technology-Enriched Language-Art Projects: A Case Study

ERIC Educational Resources Information Center

Lee, Young-Jin

2010-01-01

Teaching computer programming to young children has been considered difficult because of its abstract and complex nature. The objectives of this study are (1) to investigate whether an innovative educational technology tool called Scratch could enable young children to learn abstract knowledge of computer programming while creating multimedia…

Basic BASIC; An Introduction to Computer Programming in BASIC Language.

ERIC Educational Resources Information Center

Coan, James S.

With the increasing availability of computer access through remote terminals and time sharing, more and more schools and colleges are able to introduce programing to substantial numbers of students. This book is an attempt to incorporate computer programming, using BASIC language, and the teaching of mathematics. The general approach of the book…

48 CFR 227.7104 - Contracts under the Small Business Innovation Research (SBIR) Program.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Data and Computer Software—Small Business Innovation Research (SBIR) Program, when technical data or computer software will be generated during performance of contracts under the SBIR program. (b) Under the clause at 252.227-7018, the Government obtains SBIR data rights in technical data and computer software...

48 CFR 227.7104 - Contracts under the Small Business Innovation Research (SBIR) Program.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Data and Computer Software—Small Business Innovation Research (SBIR) Program, when technical data or computer software will be generated during performance of contracts under the SBIR program. (b) Under the clause at 252.227-7018, the Government obtains SBIR data rights in technical data and computer software...

A general program to compute the multivariable stability margin for systems with parametric uncertainty

NASA Technical Reports Server (NTRS)

Sanchez Pena, Ricardo S.; Sideris, Athanasios

1988-01-01

A computer program implementing an algorithm for computing the multivariable stability margin to check the robust stability of feedback systems with real parametric uncertainty is proposed. The authors present in some detail important aspects of the program. An example is presented using lateral directional control system.

48 CFR 252.227-7018 - Rights in noncommercial technical data and computer software-Small Business Innovation Research...

Code of Federal Regulations, 2010 CFR

2010-10-01

... technical data and computer software-Small Business Innovation Research (SBIR) Program. 252.227-7018 Section... Innovation Research (SBIR) Program. As prescribed in 227.7104(a), use the following clause: Rights in Noncommercial Technical Data and Computer Software—Small Business Innovation Research (SBIR) Program (JUN 1995...

48 CFR 252.227-7018 - Rights in noncommercial technical data and computer software-Small Business Innovation Research...

Code of Federal Regulations, 2014 CFR

2014-10-01

... technical data and computer software-Small Business Innovation Research (SBIR) Program. 252.227-7018 Section... Innovation Research (SBIR) Program. As prescribed in 227.7104(a), use the following clause: Rights in Noncommercial Technical Data and Computer Software—Small Business Innovation Research (SBIR) Program (FEB 2014...

48 CFR 252.227-7018 - Rights in noncommercial technical data and computer software-Small Business Innovation Research...

Code of Federal Regulations, 2011 CFR

2011-10-01

... technical data and computer software-Small Business Innovation Research (SBIR) Program. 252.227-7018 Section... Innovation Research (SBIR) Program. As prescribed in 227.7104(a), use the following clause: Rights in Noncommercial Technical Data and Computer Software—Small Business Innovation Research (SBIR) Program (MAR 2011...

48 CFR 252.227-7018 - Rights in noncommercial technical data and computer software-Small Business Innovation Research...

Code of Federal Regulations, 2013 CFR

2013-10-01

... technical data and computer software-Small Business Innovation Research (SBIR) Program. 252.227-7018 Section... Innovation Research (SBIR) Program. As prescribed in 227.7104(a), use the following clause: Rights in Noncommercial Technical Data and Computer Software—Small Business Innovation Research (SBIR) Program (MAY 2013...

77 FR 34941 - Privacy Act of 1974; Notice of a Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

...; Notice of a Computer Matching Program AGENCY: Defense Manpower Data Center, DoD. ACTION: Notice of a... computer matching program are the Department of Veterans Affairs (VA) and the Defense Manpower Data Center... identified as DMDC 01, entitled ``Defense Manpower Data Center Data Base,'' last published in the Federal...

77 FR 35432 - Privacy Act of 1974, Computer Matching Program: United States Postal Service and the Defense...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-13

... the Defense Manpower Data Center, Department of Defense AGENCY: Postal Service TM . ACTION: Notice of Computer Matching Program--United States Postal Service and the Defense Manpower Data Center, Department of... as the recipient agency in a computer matching program with the Defense Manpower Data Center (DMDC...

Adult Learning in a Computer-Based ESL Acquisition Program

ERIC Educational Resources Information Center

Sanchez, Karen Renee

2013-01-01

This study explores the self-efficacy of students learning English as a Second Language on the computer-based Rosetta Stone program. The research uses a qualitative approach to explore how a readily available computer-based learning program, Rosetta Stone, can help adult immigrant students gain some English competence and so acquire a greater…

22 CFR 1101.4 - Reports on new systems of records; computer matching programs.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 22 Foreign Relations 2 2012-04-01 2009-04-01 true Reports on new systems of records; computer matching programs. 1101.4 Section 1101.4 Foreign Relations INTERNATIONAL BOUNDARY AND WATER COMMISSION... records; computer matching programs. (a) Before establishing any new systems of records, or making any...

22 CFR 1101.4 - Reports on new systems of records; computer matching programs.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 22 Foreign Relations 2 2014-04-01 2014-04-01 false Reports on new systems of records; computer matching programs. 1101.4 Section 1101.4 Foreign Relations INTERNATIONAL BOUNDARY AND WATER COMMISSION... records; computer matching programs. (a) Before establishing any new systems of records, or making any...

22 CFR 1101.4 - Reports on new systems of records; computer matching programs.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 22 Foreign Relations 2 2013-04-01 2009-04-01 true Reports on new systems of records; computer matching programs. 1101.4 Section 1101.4 Foreign Relations INTERNATIONAL BOUNDARY AND WATER COMMISSION... records; computer matching programs. (a) Before establishing any new systems of records, or making any...

77 FR 32709 - Privacy Act of 1974, as Amended; Computer Matching Program (SSA/Department of Homeland Security...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA 2011-0089] Privacy Act of 1974, as Amended; Computer Matching Program (SSA/ Department of Homeland Security (DHS))--Match Number 1010 AGENCY: Social Security Administration (SSA). ACTION: Notice of a renewal of an existing computer matching program that...

78 FR 37647 - Privacy Act of 1974, as Amended; Computer Matching Program (SSA/Railroad Retirement Board (RRB...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-21

... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA 2013-0010] Privacy Act of 1974, as Amended; Computer Matching Program (SSA/ Railroad Retirement Board (RRB))--Match Number 1006 AGENCY: Social Security Administration. ACTION: Notice of a renewal of an existing computer matching program that will expire on...

40 CFR Appendix C to Part 66 - Computer Program

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 15 2011-07-01 2011-07-01 false Computer Program C Appendix C to Part...) ASSESSMENT AND COLLECTION OF NONCOMPLIANCE PENALTIES BY EPA Pt. 66, App. C Appendix C to Part 66—Computer Program Note: For text of appendix C see appendix C to part 67. ...

22 CFR 1101.4 - Reports on new systems of records; computer matching programs.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 22 Foreign Relations 2 2011-04-01 2009-04-01 true Reports on new systems of records; computer matching programs. 1101.4 Section 1101.4 Foreign Relations INTERNATIONAL BOUNDARY AND WATER COMMISSION... records; computer matching programs. (a) Before establishing any new systems of records, or making any...

The Shock and Vibration Digest. Volume 14, Number 11

DTIC Science & Technology

1982-11-01

cooled reactor 1981) ( HTGR ) core under seismic excitation his been developed . N82-18644 The computer program can be used to predict the behavior (In...French) of the HTGR core under seismic excitation. Key Words: Computer programs , Modal analysis, Beams, Undamped structures A computation method is...30) PROGRAMMING c c Dale and Cohen [221 extended the method of McMunn and Plunkett [201 developed a compute- McMunn and Plunkett to continuous systems

Improvements in Routing for Packet-Switched Networks

DTIC Science & Technology

1975-02-18

PROGRAM FOR COMPUTER SIMULATION . . 90 B.l Flow Diagram of Adaptive Routine 90 B.2 Progiam ARPSIM 93 B.3 Explanation of Variables...equa. 90 APPENDIX B ADAPTIVE ROUTING PROGRAM FOR COMPUTER SIMULA HON The computer simulation for adaptive routing was initially run on a DDP-24 small...TRANSMIT OVER AVAILABLE LINKS MESSAGES IN QUEUE COMPUTE Ni NUMBER OF ARRIVALS AT EACH NODE i AT TIME T Fig. Bla - Flow Diagram of Program Routine 92

Comparison of Building Loads Analysis and System Thermodynamics (BLAST) Computer Program Simulations and Measured Energy Use for Army Buildings.

DTIC Science & Technology

1980-05-01

engineering ,ZteNo D R RPTE16 research w 9 laboratory COMPARISON OF BUILDING LOADS ANALYSIS AND SYSTEM THERMODYNAMICS (BLAST) AD 0 5 5,0 3COMPUTER PROGRAM...Building Loads Analysis and System Thermodynamics (BLAST) computer program. A dental clinic and a battalion headquarters and classroom building were...Building and HVAC System Data Computer Simulation Comparison of Actual and Simulated Results ANALYSIS AND FINDINGS

MPL-A program for computations with iterated integrals on moduli spaces of curves of genus zero

NASA Astrophysics Data System (ADS)

Bogner, Christian

2016-06-01

We introduce the Maple program MPL for computations with multiple polylogarithms. The program is based on homotopy invariant iterated integrals on moduli spaces M0,n of curves of genus 0 with n ordered marked points. It includes the symbol map and procedures for the analytic computation of period integrals on M0,n. It supports the automated computation of a certain class of Feynman integrals.

Coal-seismic, desktop computer programs in BASIC; Part 6, Develop rms velocity functions and apply mute and normal movement

USGS Publications Warehouse

Hasbrouck, W.P.

1983-01-01

Processing of data taken with the U.S. Geological Survey's coal-seismic system is done with a desktop, stand-alone computer. Programs for this computer are written in the extended BASIC language utilized by the Tektronix 4051 Graphic System. This report presents computer programs used to develop rms velocity functions and apply mute and normal moveout to a 12-trace seismogram.

Cost-Benefit Analysis for ECIA Chapter 1 and State DPPF Programs Comparing Groups Receiving Regular Program Instruction and Groups Receiving Computer Assisted Instruction/Computer Management System (CAI/CMS). 1986-87.

ERIC Educational Resources Information Center

Chamberlain, Ed

A cost benefit study was conducted to determine the effectiveness of a computer assisted instruction/computer management system (CAI/CMS) as an alternative to conventional methods of teaching reading within Chapter 1 and DPPF funded programs of the Columbus (Ohio) Public Schools. The Chapter 1 funded Compensatory Language Experiences and Reading…

Upper Grades Ideas.

ERIC Educational Resources Information Center

Thornburg, David; Beane, Pam

1983-01-01

Presents programming ideas using LOGO, activity for converting flowchart into a computer program, and a Pascal program for generating music using paddles. Includes the article "Helping Computers Adapt to Kids" by Philip Nothnagle; a program for estimating length of lines is included. (JN)

Developing a computer security training program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-01-01

We all know that training can empower the computer protection program. However, pushing computer security information outside the computer security organization into the rest of the company is often labeled as an easy project or a dungeon full of dragons. Used in part or whole, the strategy offered in this paper may help the developer of a computer security training program ward off dragons and create products and services. The strategy includes GOALS (what the result of training will be), POINTERS (tips to ensure survival), and STEPS (products and services as a means to accomplish the goals).

Refinement Of Hexahedral Cells In Euler Flow Computations

NASA Technical Reports Server (NTRS)

Melton, John E.; Cappuccio, Gelsomina; Thomas, Scott D.

1996-01-01

Topologically Independent Grid, Euler Refinement (TIGER) computer program solves Euler equations of three-dimensional, unsteady flow of inviscid, compressible fluid by numerical integration on unstructured hexahedral coordinate grid refined where necessary to resolve shocks and other details. Hexahedral cells subdivided, each into eight smaller cells, as needed to refine computational grid in regions of high flow gradients. Grid Interactive Refinement and Flow-Field Examination (GIRAFFE) computer program written in conjunction with TIGER program to display computed flow-field data and to assist researcher in verifying specified boundary conditions and refining grid.

Calculation of inviscid surface streamlines and heat transfer on shuttle type configurations. Part 2: Description of computer program

NASA Technical Reports Server (NTRS)

Dejarnette, F. R.; Jones, M. H.

1971-01-01

A description of the computer program used for heating rate calculation for blunt bodies in hypersonic flow is given. The main program and each subprogram are described by defining the pertinent symbols involved and presenting a detailed flow diagram and complete computer program listing. Input and output parameters are discussed in detail. Listings are given for the computation of heating rates on (1) a blunted 15 deg half-angle cone at 20 deg incidence and Mach 10.6, (2) a blunted 70 deg slab delta wing at 10 deg incidence and Mach 8, and (3) the HL-10 lifting body at 20 deg incidence and Mach 10. In addition, the computer program output for two streamlines on the blunted 15 deg half-angle cone is listed. For Part 1, see N71-36186.

New reflective symmetry design capability in the JPL-IDEAS Structure Optimization Program

NASA Technical Reports Server (NTRS)

Strain, D.; Levy, R.

1986-01-01

The JPL-IDEAS antenna structure analysis and design optimization computer program was modified to process half structure models of symmetric structures subjected to arbitrary external static loads, synthesize the performance, and optimize the design of the full structure. Significant savings in computation time and cost (more than 50%) were achieved compared to the cost of full model computer runs. The addition of the new reflective symmetry analysis design capabilities to the IDEAS program allows processing of structure models whose size would otherwise prevent automated design optimization. The new program produced synthesized full model iterative design results identical to those of actual full model program executions at substantially reduced cost, time, and computer storage.

Protection of Computer Programs--A Dilemma.

ERIC Educational Resources Information Center

Carnahan, William H.

Computer programs, as legitimate original inventions or creative written expressions, are entitled to patent or copyright protection. Understanding the legal implications of this concept is crucial to both computer programmers and their employers in our increasingly computer-oriented way of life. Basically the copyright or patent procedure…

Coal-seismic, desktop computer programs in BASIC; Part 7, Display and compute shear-pair seismograms

USGS Publications Warehouse

Hasbrouck, W.P.

1983-01-01

Processing of geophysical data taken with the U.S. Geological Survey's coal-seismic system is done with a desk-top, stand-alone computer. Programs for this computer are written in the extended BASIC language utilized by the Tektronix 4051 Graphic System. This report discusses and presents five computer pro grams used to display and compute shear-pair seismograms.

Tools for Administration of a UNIX-Based Network

NASA Technical Reports Server (NTRS)

LeClaire, Stephen; Farrar, Edward

2004-01-01

Several computer programs have been developed to enable efficient administration of a large, heterogeneous, UNIX-based computing and communication network that includes a variety of computers connected to a variety of subnetworks. One program provides secure software tools for administrators to create, modify, lock, and delete accounts of specific users. This program also provides tools for users to change their UNIX passwords and log-in shells. These tools check for errors. Another program comprises a client and a server component that, together, provide a secure mechanism to create, modify, and query quota levels on a network file system (NFS) mounted by use of the VERITAS File SystemJ software. The client software resides on an internal secure computer with a secure Web interface; one can gain access to the client software from any authorized computer capable of running web-browser software. The server software resides on a UNIX computer configured with the VERITAS software system. Directories where VERITAS quotas are applied are NFS-mounted. Another program is a Web-based, client/server Internet Protocol (IP) address tool that facilitates maintenance lookup of information about IP addresses for a network of computers.

Computer Program for the Design and Off-Design Performance of Turbojet and Turbofan Engine Cycles

NASA Technical Reports Server (NTRS)

Morris, S. J.

1978-01-01

The rapid computer program is designed to be run in a stand-alone mode or operated within a larger program. The computation is based on a simplified one-dimensional gas turbine cycle. Each component in the engine is modeled thermo-dynamically. The component efficiencies used in the thermodynamic modeling are scaled for the off-design conditions from input design point values using empirical trends which are included in the computer code. The engine cycle program is capable of producing reasonable engine performance prediction with a minimum of computer execute time. The current computer execute time on the IBM 360/67 for one Mach number, one altitude, and one power setting is about 0.1 seconds. about 0.1 seconds. The principal assumption used in the calculation is that the compressor is operated along a line of maximum adiabatic efficiency on the compressor map. The fluid properties are computed for the combustion mixture, but dissociation is not included. The procedure included in the program is only for the combustion of JP-4, methane, or hydrogen.

Program manual for the Shuttle Electric Power System analysis computer program (SEPS), volume 1 of program documentation

NASA Technical Reports Server (NTRS)

Bains, R. W.; Herwig, H. A.; Luedeman, J. K.; Torina, E. M.

1974-01-01

The Shuttle Electric Power System (SEPS) computer program is considered in terms of the program manual, programmer guide, and program utilization. The main objective is to provide the information necessary to interpret and use the routines comprising the SEPS program. Subroutine descriptions including the name, purpose, method, variable definitions, and logic flow are presented.

Development and evaluation of a computer program to grade student performance on peripheral blood smears

NASA Astrophysics Data System (ADS)

Lehman, Donald Clifford

Today's medical laboratories are dealing with cost containment health care policies and unfilled laboratory positions. Because there may be fewer experienced clinical laboratory scientists, students graduating from clinical laboratory science (CLS) programs are expected by their employers to perform accurately in entry-level positions with minimal training. Information in the CLS field is increasing at a dramatic rate, and instructors are expected to teach more content in the same amount of time with the same resources. With this increase in teaching obligations, instructors could use a tool to facilitate grading. The research question was, "Can computer-assisted assessment evaluate students in an accurate and time efficient way?" A computer program was developed to assess CLS students' ability to evaluate peripheral blood smears. Automated grading permits students to get results quicker and allows the laboratory instructor to devote less time to grading. This computer program could improve instruction by providing more time to students and instructors for other activities. To be valuable, the program should provide the same quality of grading as the instructor. These benefits must outweigh potential problems such as the time necessary to develop and maintain the program, monitoring of student progress by the instructor, and the financial cost of the computer software and hardware. In this study, surveys of students and an interview with the laboratory instructor were performed to provide a formative evaluation of the computer program. In addition, the grading accuracy of the computer program was examined. These results will be used to improve the program for use in future courses.

Structured Design Language for Computer Programs

NASA Technical Reports Server (NTRS)

Pace, Walter H., Jr.

1986-01-01

Box language used at all stages of program development. Developed to provide improved productivity in designing, coding, and maintaining computer programs. BOX system written in FORTRAN 77 for batch execution.

Computer Literacy and the Library: A New Connection.

ERIC Educational Resources Information Center

Fenske, Rachel F.

1998-01-01

Describes a program at Eastern Washington University that integrates library skills as a component of the English composition program, and is part of a computer-literacy program stemming from a general-education curriculum reform. Discusses program development and design, assessment of student learning, and effectiveness of the program. (LRW)

Conceptions of Programming: A Study into Learning To Program.

ERIC Educational Resources Information Center

Booth, Shirley

This paper reports the results of a phenomenographic study which focused on identifying and describing the conceptions of programming and related phenomena of about 120 computer science and computer engineering students learning to program. The report begins by tracing developments in the students' conceptions of programming and its parts, and…

Video and Computer Technologies for Extended-Campus Programming.

ERIC Educational Resources Information Center

Sagan, Edgar L.; And Others

This paper discusses video and computer technologies for extended-campus programming (courses and programs at off-campus sites). The first section provides an overview of the distance education program at the University of Kentucky (UK), and highlights the improved access to graduate and professional programs, advances in technology, funding,…

Development of Integrated Programs for Aerospace-vehicle design (IPAD): Integrated information processing requirements

NASA Technical Reports Server (NTRS)

Southall, J. W.

1979-01-01

The engineering-specified requirements for integrated information processing by means of the Integrated Programs for Aerospace-Vehicle Design (IPAD) system are presented. A data model is described and is based on the design process of a typical aerospace vehicle. General data management requirements are specified for data storage, retrieval, generation, communication, and maintenance. Information management requirements are specified for a two-component data model. In the general portion, data sets are managed as entities, and in the specific portion, data elements and the relationships between elements are managed by the system, allowing user access to individual elements for the purpose of query. Computer program management requirements are specified for support of a computer program library, control of computer programs, and installation of computer programs into IPAD.

THERMTRAJ: A FORTRAN program to compute the trajectory and gas film temperatures of zero pressure balloons

NASA Technical Reports Server (NTRS)

Horn, W. J.; Carlson, L. A.

1983-01-01

A FORTRAN computer program called THERMTRAJ is presented which can be used to compute the trajectory of high altitude scientific zero pressure balloons from launch through all subsequent phases of the balloon flight. In addition, balloon gas and film temperatures can be computed at every point of the flight. The program has the ability to account for ballasting, changes in cloud cover, variable atmospheric temperature profiles, and both unconditional valving and scheduled valving of the balloon gas. The program was verified for an extensive range of balloon sizes (from 0.5 to 41.47 million cubic feet). Instructions on program usage, listing of the program source deck, input data and printed and plotted output for a verification case are included.

Computer program for a four-cylinder-Stirling-engine controls simulation

NASA Technical Reports Server (NTRS)

Daniels, C. J.; Lorenzo, C. F.

1982-01-01

A four cylinder Stirling engine, transient engine simulation computer program is presented. The program is intended for controls analysis. The associated engine model was simplified to shorten computer calculation time. The model includes engine mechanical drive dynamics and vehicle load effects. The computer program also includes subroutines that allow: (1) acceleration of the engine by addition of hydrogen to the system, and (2) braking of the engine by short circuiting of the working spaces. Subroutines to calculate degraded engine performance (e.g., due to piston ring and piston rod leakage) are provided. Input data required to run the program are described and flow charts are provided. The program is modular to allow easy modification of individual routines. Examples of steady state and transient results are presented.

Computer program for calculating supersonic flow about circular, elliptic, and bielliptic cones by the method of lines

NASA Technical Reports Server (NTRS)

Klunker, E. B.; South, J. C., Jr.; Davis, R. M.

1972-01-01

A user's manual for a computer program which calculates the supersonic flow about circular, elliptic, and bielliptic cones at incidence and elliptic cones at yaw by the method of lines is presented. The program is automated to compute a case from known or easily calculated solution by changing the parameters through a sequence of steps. It provides information including the shock shape, flow field, isentropic surface properties, entropy layer, and force coefficients. A description of the program operation, sample computations, and a FORTRAN 4 listing are presented.

Generalized environmental control and life support system computer program (G189A) configuration control. [computer subroutine libraries for shuttle orbiter analyses

NASA Technical Reports Server (NTRS)

Blakely, R. L.

1973-01-01

A G189A simulation of the shuttle orbiter EC/lSS was prepared and used to study payload support capabilities. Two master program libraries of the G189A computer program were prepared for the NASA/JSC computer system. Several new component subroutines were added to the G189A program library and many existing subroutines were revised to improve their capabilities. A number of special analyses were performed in support of a NASA/JSC shuttle orbiter EC/LSS payload support capability study.

GYC: A program to compute the turbulent boundary layer on a rotating cone

NASA Technical Reports Server (NTRS)

Sullivan, R. D.

1976-01-01

A computer program, GYC, which is capable of computing the properties of a compressible turbulent boundary layer on a rotating axisymmetric cone-cylinder body, according to the principles of invariant modeling was studied. The program is extended to include the calculation of the turbulence scale by a differential equation. GYC is in operation on the CDC-7600 computer and has undergone several corrections and improvements as a result of the experience gained. The theoretical basis for the program and the method of implementation, as well as information on its operation are given.

Transpiration and film cooling boundary layer computer program. Volume 2: Computer program and user's manual

NASA Technical Reports Server (NTRS)

Gloss, R. J.

1971-01-01

A finite difference turbulent boundary layer computer program which allows for mass transfer wall cooling and equilibrium chemistry effects is presented. The program is capable of calculating laminar or turbulent boundary layer solutions for an arbitrary ideal gas or an equilibrium hydrogen oxygen system. Either two dimensional or axisymmetric geometric configurations may be considered. The equations are solved, in nondimension-alized physical coordinates, using the implicit Crank-Nicolson technique. The finite difference forms of the conservation of mass, momentum, total enthalpy and elements equations are linearized and uncoupled, thereby generating easily solvable tridiagonal sets of algebraic equations. A detailed description of the computer program, as well as a program user's manual is provided. Detailed descriptions of all boundary layer subroutines are included, as well as a section defining all program symbols of principal importance. Instructions are then given for preparing card input to the program and for interpreting the printed output. Finally, two sample cases are included to illustrate the use of the program.

Computer Recreations.

ERIC Educational Resources Information Center

Dewdney, A. K.

1989-01-01

Reviews the performance of computer programs for writing poetry and prose, including MARK V. SHANEY, MELL, POETRY GENERATOR, THUNDER THOUGHT, and ORPHEUS. Discusses the writing principles of the programs. Provides additional information on computer magnification techniques. (YP)

My Computer Is Learning.

ERIC Educational Resources Information Center

Good, Ron

1986-01-01

Describes instructional uses of computer programs found in David Heiserman's book "Projects in Machine Intelligence for Your Home Computer." The programs feature "creatures" of various colors that move around within a rectangular white border. (JN)

Protecting Your Computer from Viruses

ERIC Educational Resources Information Center

Descy, Don E.

2006-01-01

A computer virus is defined as a software program capable of reproducing itself and usually capable of causing great harm to files or other programs on the same computer. The existence of computer viruses--or the necessity of avoiding viruses--is part of using a computer. With the advent of the Internet, the door was opened wide for these…

The Computer as a Teaching Aid for Eleventh Grade Mathematics: A Comparison Study.

ERIC Educational Resources Information Center

Kieren, Thomas Ervin

To determine the effect of learning computer programming and the use of a computer on mathematical achievement of eleventh grade students, for each of two years, average and above average students were randomly assigned to an experimental and control group. The experimental group wrote computer programs and used the output from the computer in…

Computer Technology for Industry

NASA Technical Reports Server (NTRS)

1979-01-01

In this age of the computer, more and more business firms are automating their operations for increased efficiency in a great variety of jobs, from simple accounting to managing inventories, from precise machining to analyzing complex structures. In the interest of national productivity, NASA is providing assistance both to longtime computer users and newcomers to automated operations. Through a special technology utilization service, NASA saves industry time and money by making available already developed computer programs which have secondary utility. A computer program is essentially a set of instructions which tells the computer how to produce desired information or effect by drawing upon its stored input. Developing a new program from scratch can be costly and time-consuming. Very often, however, a program developed for one purpose can readily be adapted to a totally different application. To help industry take advantage of existing computer technology, NASA operates the Computer Software Management and Information Center (COSMIC)(registered TradeMark),located at the University of Georgia. COSMIC maintains a large library of computer programs developed for NASA, the Department of Defense, the Department of Energy and other technology-generating agencies of the government. The Center gets a continual flow of software packages, screens them for adaptability to private sector usage, stores them and informs potential customers of their availability.

Programs for Fundamentals of Chemistry.

ERIC Educational Resources Information Center

Gallardo, Julio; Delgado, Steven

This document provides computer programs, written in BASIC PLUS, for presenting fundamental or remedial college chemistry students with chemical problems in a computer assisted instructional program. Programs include instructions, a sample run, and 14 separate practice sessions covering: mathematical operations, using decimals, solving…

Changing the Paradigm: Preparing Students for the Computing Profession in the 21st Century

NASA Technical Reports Server (NTRS)

Robbins, Kay A.

2003-01-01

The dramatic technological developments of the past decade have led to a tremendous growth in the demand for computer science professionals well-versed in advanced technology and techniques. NASA, traditionally a haven for cutting-edge innovators, is now competing with every industrial and government sector for computer science talent. The computer science program at University of Texas at San Antonio (UTSA) faces challenges beyond those intrinsically presented by rapid technological change, because a significant number of UTSA students come from low-income families with no Internet or computer access at home. An examination of enrollment statistics for the computer science program at UTSA showed that very few students who entered as freshmen successfully graduated. The upper division courses appeared to be populated by graduate students removing deficiencies and by transfer students. The faculty was also concerned that the students who did graduate from the program did not have the strong technical and programming skills that the CS program had been noted for in the community during the 1980's.

VASCOMP 2. The V/STOL aircraft sizing and performance computer program. Volume 6: User's manual, revision 3

NASA Technical Reports Server (NTRS)

Schoen, A. H.; Rosenstein, H.; Stanzione, K.; Wisniewski, J. S.

1980-01-01

This report describes the use of the V/STOL Aircraft Sizing and Performance Computer Program (VASCOMP II). The program is useful in performing aircraft parametric studies in a quick and cost efficient manner. Problem formulation and data development were performed by the Boeing Vertol Company and reflects the present preliminary design technology. The computer program, written in FORTRAN IV, has a broad range of input parameters, to enable investigation of a wide variety of aircraft. User oriented features of the program include minimized input requirements, diagnostic capabilities, and various options for program flexibility.

Automatic system for computer program documentation

NASA Technical Reports Server (NTRS)

Simmons, D. B.; Elliott, R. W.; Arseven, S.; Colunga, D.

1972-01-01

Work done on a project to design an automatic system for computer program documentation aids was made to determine what existing programs could be used effectively to document computer programs. Results of the study are included in the form of an extensive bibliography and working papers on appropriate operating systems, text editors, program editors, data structures, standards, decision tables, flowchart systems, and proprietary documentation aids. The preliminary design for an automated documentation system is also included. An actual program has been documented in detail to demonstrate the types of output that can be produced by the proposed system.

Multithreaded transactions in scientific computing: New versions of a computer program for kinematical calculations of RHEED intensity oscillations

NASA Astrophysics Data System (ADS)

Brzuszek, Marcin; Daniluk, Andrzej

2006-11-01

Writing a concurrent program can be more difficult than writing a sequential program. Programmer needs to think about synchronisation, race conditions and shared variables. Transactions help reduce the inconvenience of using threads. A transaction is an abstraction, which allows programmers to group a sequence of actions on the program into a logical, higher-level computation unit. This paper presents multithreaded versions of the GROWTH program, which allow to calculate the layer coverages during the growth of thin epitaxial films and the corresponding RHEED intensities according to the kinematical approximation. The presented programs also contain graphical user interfaces, which enable displaying program data at run-time. New version program summaryTitles of programs:GROWTHGr, GROWTH06 Catalogue identifier:ADVL_v2_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADVL_v2_0 Program obtainable from:CPC Program Library, Queen's University of Belfast, N. Ireland Catalogue identifier of previous version:ADVL Does the new version supersede the original program:No Computer for which the new version is designed and others on which it has been tested: Pentium-based PC Operating systems or monitors under which the new version has been tested: Windows 9x, XP, NT Programming language used:Object Pascal Memory required to execute with typical data:More than 1 MB Number of bits in a word:64 bits Number of processors used:1 No. of lines in distributed program, including test data, etc.:20 931 Number of bytes in distributed program, including test data, etc.: 1 311 268 Distribution format:tar.gz Nature of physical problem: The programs compute the RHEED intensities during the growth of thin epitaxial structures prepared using the molecular beam epitaxy (MBE). The computations are based on the use of kinematical diffraction theory [P.I. Cohen, G.S. Petrich, P.R. Pukite, G.J. Whaley, A.S. Arrott, Surf. Sci. 216 (1989) 222. [1

Identification of Program Signatures from Cloud Computing System Telemetry Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nichols, Nicole M.; Greaves, Mark T.; Smith, William P.

Malicious cloud computing activity can take many forms, including running unauthorized programs in a virtual environment. Detection of these malicious activities while preserving the privacy of the user is an important research challenge. Prior work has shown the potential viability of using cloud service billing metrics as a mechanism for proxy identification of malicious programs. Previously this novel detection method has been evaluated in a synthetic and isolated computational environment. In this paper we demonstrate the ability of billing metrics to identify programs, in an active cloud computing environment, including multiple virtual machines running on the same hypervisor. The openmore » source cloud computing platform OpenStack, is used for private cloud management at Pacific Northwest National Laboratory. OpenStack provides a billing tool (Ceilometer) to collect system telemetry measurements. We identify four different programs running on four virtual machines under the same cloud user account. Programs were identified with up to 95% accuracy. This accuracy is dependent on the distinctiveness of telemetry measurements for the specific programs we tested. Future work will examine the scalability of this approach for a larger selection of programs to better understand the uniqueness needed to identify a program. Additionally, future work should address the separation of signatures when multiple programs are running on the same virtual machine.« less

A Reading Skills Development Program for Adult Non-Readers. Featuring: Supplementary Graphics and Sound (Voice Tutorials). Volumes 1 and 2. The TRS-80 Computer Assisted Instruction Series for Adult Basic Education Students.

ERIC Educational Resources Information Center

San Antonio State Hospital, TX. Office of Education Services.

This instructional manual consists of materials for use in implementing a computer-assisted instructional program in reading skills development for adult nonreaders. Discussed first are the project during which this instructional program and manual were developed and the goals of the computer-assisted beginning reading program, a major feature of…

Mass Memory Storage Devices for AN/SLQ-32(V).

DTIC Science & Technology

1985-06-01

tactical programs and libraries into the AN/UYK-19 computer , the RP-16 microprocessor, and other peripheral processors (e.g., ADLS and Band 1) will be...software must be loaded into computer memory from the 4-track magnetic tape cartridges (MTCs) on which the programs are stored. Program load begins...software. Future computer programs , which will reside in peripheral processors, include the Automated Decoy Launching System (ADLS) and Band 1. As

The Use and Misuse of Computers in Education: Evidence from a Randomized Experiment in Colombia. Impact Evaluation Series No. 29. Policy Research Working Paper 4836

ERIC Educational Resources Information Center

Barrera-Osorio, Felipe; Linden, Leigh L.

2009-01-01

This paper presents the evaluation of the program Computers for Education. The program aims to integrate computers, donated by the private sector, into the teaching of language in public schools. The authors conduct a two-year randomized evaluation of the program using a sample of 97 schools and 5,201 children. Overall, the program seems to have…

Modeling and Analysis of Power Processing Systems (MAPPS). Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Lee, F. C.; Radman, S.; Carter, R. A.; Wu, C. H.; Yu, Y.; Chang, R.

1980-01-01

The computer programs and derivations generated in support of the modeling and design optimization program are presented. Programs for the buck regulator, boost regulator, and buck-boost regulator are described. The computer program for the design optimization calculations is presented. Constraints for the boost and buck-boost converter were derived. Derivations of state-space equations and transfer functions are presented. Computer lists for the converters are presented, and the input parameters justified.

78 FR 1275 - Privacy Act of 1974; Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-08

... Social Security Administration (Computer Matching Agreement 1071). SUMMARY: In accordance with the... of its new computer matching program with the Social Security Administration (SSA). DATES: OPM will... conditions under which SSA will disclose Social Security benefit data to OPM via direct computer link. OPM...

EZLP: An Interactive Computer Program for Solving Linear Programming Problems. Final Report.

ERIC Educational Resources Information Center

Jarvis, John J.; And Others

Designed for student use in solving linear programming problems, the interactive computer program described (EZLP) permits the student to input the linear programming model in exactly the same manner in which it would be written on paper. This report includes a brief review of the development of EZLP; narrative descriptions of program features,…

Formatting scripts with computers and Extended BASIC.

PubMed

Menning, C B

1984-02-01

A computer program, written in the language of Extended BASIC, is presented which enables scripts, for educational media, to be quickly written in a nearly unformatted style. From the resulting script file, stored on magnetic tape or disk, the computer program formats the script into either a storyboard , a presentation, or a narrator 's script. Script headings and page and paragraph numbers are automatic features in the word processing. Suggestions are given for making personal modifications to the computer program.

Coal-seismic, desktop computer programs in BASIC; Part 5, Perform X-square T-square analysis and plot normal moveout lines on seismogram overlay

USGS Publications Warehouse

Hasbrouck, W.P.

1983-01-01

Processing of data taken with the U.S. Geological Survey's coal-seismic system is done with a desktop, stand-alone computer. Programs for this computer are written in the extended BASIC language used by the Tektronix 4051 Graphic System. This report presents computer programs to perform X-square/T-square analyses and to plot normal moveout lines on a seismogram overlay.

Computer Programs For Automated Welding System

NASA Technical Reports Server (NTRS)

Agapakis, John E.

1993-01-01

Computer programs developed for use in controlling automated welding system described in MFS-28578. Together with control computer, computer input and output devices and control sensors and actuators, provide flexible capability for planning and implementation of schemes for automated welding of specific workpieces. Developed according to macro- and task-level programming schemes, which increases productivity and consistency by reducing amount of "teaching" of system by technician. System provides for three-dimensional mathematical modeling of workpieces, work cells, robots, and positioners.

DEP : a computer program for evaluating lumber drying costs and investments

Treesearch

Stewart Holmes; George B. Harpole; Edward Bilek

1983-01-01

The DEP computer program is a modified discounted cash flow computer program designed for analysis of problems involving economic analysis of wood drying processes. Wood drying processes are different from other processes because of the large amounts of working capital required to finance inventories, and because of relatively large shares of costs charged to inventory...

The Identification, Implementation, and Evaluation of Critical User Interface Design Features of Computer-Assisted Instruction Programs in Mathematics for Students with Learning Disabilities

ERIC Educational Resources Information Center

Seo, You-Jin; Woo, Honguk

2010-01-01

Critical user interface design features of computer-assisted instruction programs in mathematics for students with learning disabilities and corresponding implementation guidelines were identified in this study. Based on the identified features and guidelines, a multimedia computer-assisted instruction program, "Math Explorer", which delivers…

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--STANDARD OPERATING PROCEDURE FOR PERFORMANCE OF COMPUTER SOFTWARE: VERIFICATION AND VALIDATION (IIT-A-2.0)

EPA Science Inventory

The purpose of this SOP is to define the procedures for the initial and periodic verification and validation of computer programs. The programs are used during the Arizona NHEXAS project and Border study at the Illinois Institute of Technology (IIT) site. Keywords: computers; s...

Operations analysis (study 2.1). Program listing for the LOVES computer code

NASA Technical Reports Server (NTRS)

Wray, S. T., Jr.

1974-01-01

A listing of the LOVES computer program is presented. The program is coded partially in SIMSCRIPT and FORTRAN. This version of LOVES is compatible with both the CDC 7600 and the UNIVAC 1108 computers. The code has been compiled, loaded, and executed successfully on the EXEC 8 system for the UNIVAC 1108.

Theory and Programs for Dynamic Modeling of Tree Rings from Climate

Treesearch

Paul C. van Deusen; Jennifer Koretz

1988-01-01

Computer programs written in GAUSS(TM) for IBM compatible personal computers are described that perform dynamic tree ring modeling with climate data; the underlying theory is also described. The programs and a separate users manual are available from the authors, although users must have the GAUSS software package on their personal computer. An example application of...

Computer program and user documentation medical data tape retrieval system

NASA Technical Reports Server (NTRS)

Anderson, J.

1971-01-01

This volume provides several levels of documentation for the program module of the NASA medical directorate mini-computer storage and retrieval system. A biomedical information system overview describes some of the reasons for the development of the mini-computer storage and retrieval system. It briefly outlines all of the program modules which constitute the system.

45 CFR 309.145 - What costs are allowable for Tribal IV-D programs carried out under § 309.65(a) of this part?

Code of Federal Regulations, 2010 CFR

2010-10-01

.... (h) Automated data processing computer systems, including: (1) Planning efforts in the identification, evaluation, and selection of an automated data processing computer system solution meeting the program... existing automated data processing computer system to support Tribal IV-D program operations, and...

45 CFR 309.145 - What costs are allowable for Tribal IV-D programs carried out under § 309.65(a) of this part?

Code of Federal Regulations, 2013 CFR

2013-10-01

.... (h) Automated data processing computer systems, including: (1) Planning efforts in the identification, evaluation, and selection of an automated data processing computer system solution meeting the program... existing automated data processing computer system to support Tribal IV-D program operations, and...

45 CFR 309.145 - What costs are allowable for Tribal IV-D programs carried out under § 309.65(a) of this part?

Code of Federal Regulations, 2014 CFR

2014-10-01

.... (h) Automated data processing computer systems, including: (1) Planning efforts in the identification, evaluation, and selection of an automated data processing computer system solution meeting the program... existing automated data processing computer system to support Tribal IV-D program operations, and...

45 CFR 309.145 - What costs are allowable for Tribal IV-D programs carried out under § 309.65(a) of this part?

Code of Federal Regulations, 2012 CFR

2012-10-01

.... (h) Automated data processing computer systems, including: (1) Planning efforts in the identification, evaluation, and selection of an automated data processing computer system solution meeting the program... existing automated data processing computer system to support Tribal IV-D program operations, and...

45 CFR 309.145 - What costs are allowable for Tribal IV-D programs carried out under § 309.65(a) of this part?

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (h) Automated data processing computer systems, including: (1) Planning efforts in the identification, evaluation, and selection of an automated data processing computer system solution meeting the program... existing automated data processing computer system to support Tribal IV-D program operations, and...

Modular space station, phase B extension. Information management advanced development. Volume 5: Software assembly

NASA Technical Reports Server (NTRS)

Gerber, C. R.

1972-01-01

The development of uniform computer program standards and conventions for the modular space station is discussed. The accomplishments analyzed are: (1) development of computer program specification hierarchy, (2) definition of computer program development plan, and (3) recommendations for utilization of all operating on-board space station related data processing facilities.

Introductory Computer Programming Course Teaching Improvement Using Immersion Language, Extreme Programming, and Education Theories

ERIC Educational Resources Information Center

Velez-Rubio, Miguel

2013-01-01

Teaching computer programming to freshmen students in Computer Sciences and other Information Technology areas has been identified as a complex activity. Different approaches have been studied looking for the best one that could help to improve this teaching process. A proposed approach was implemented which is based in the language immersion…

"Hour of Code": Can It Change Students' Attitudes toward Programming?

ERIC Educational Resources Information Center

Du, Jie; Wimmer, Hayden; Rada, Roy

2016-01-01

The Hour of Code is a one-hour introduction to computer science organized by Code.org, a non-profit dedicated to expanding participation in computer science. This study investigated the impact of the Hour of Code on students' attitudes towards computer programming and their knowledge of programming. A sample of undergraduate students from two…

Developing Student Programming and Problem-Solving Skills with Visual Basic

ERIC Educational Resources Information Center

Siegle, Del

2009-01-01

Although most computer users will never need to write a computer program, many students enjoy the challenge of creating one. Computer programming enhances students' problem solving by forcing students to break a problem into its component pieces and reassemble it in a generic format that can be understood by a nonsentient entity. It promotes…

Flexible Animation Computer Program

NASA Technical Reports Server (NTRS)

Stallcup, Scott S.

1990-01-01

FLEXAN (Flexible Animation), computer program animating structural dynamics on Evans and Sutherland PS300-series graphics workstation with VAX/VMS host computer. Typical application is animation of spacecraft undergoing structural stresses caused by thermal and vibrational effects. Displays distortions in shape of spacecraft. Program displays single natural mode of vibration, mode history, or any general deformation of flexible structure. Written in FORTRAN 77.

Exploring the Perceptions of College Instructors towards Computer Simulation Software Programs: A Quantitative Study

ERIC Educational Resources Information Center

Punch, Raymond J.

2012-01-01

The purpose of the quantitative regression study was to explore and to identify relationships between attitudes toward use and perceptions of value of computer-based simulation programs, of college instructors, toward computer based simulation programs. A relationship has been reported between attitudes toward use and perceptions of the value of…

A computer program to trace seismic ray distribution in complex two-dimensional geological models

USGS Publications Warehouse

Yacoub, Nazieh K.; Scott, James H.

1970-01-01

A computer program has been developed to trace seismic rays and their amplitudes and energies through complex two-dimensional geological models, for which boundaries between elastic units are defined by a series of digitized X-, Y-coordinate values. Input data for the program includes problem identification, control parameters, model coordinates and elastic parameter for the elastic units. The program evaluates the partitioning of ray amplitude and energy at elastic boundaries, computes the total travel time, total travel distance and other parameters for rays arising at the earth's surface. Instructions are given for punching program control cards and data cards, and for arranging input card decks. An example of printer output for a simple problem is presented. The program is written in FORTRAN IV language. The listing of the program is shown in the Appendix, with an example output from a CDC-6600 computer.

Computational techniques for solar wind flows past terrestrial planets: Theory and computer programs

NASA Technical Reports Server (NTRS)

Stahara, S. S.; Chaussee, D. S.; Trudinger, B. C.; Spreiter, J. R.

1977-01-01

The interaction of the solar wind with terrestrial planets can be predicted using a computer program based on a single fluid, steady, dissipationless, magnetohydrodynamic model to calculate the axisymmetric, supersonic, super-Alfvenic solar wind flow past both magnetic and nonmagnetic planets. The actual calculations are implemented by an assemblage of computer codes organized into one program. These include finite difference codes which determine the gas-dynamic solution, together with a variety of special purpose output codes for determining and automatically plotting both flow field and magnetic field results. Comparisons are made with previous results, and results are presented for a number of solar wind flows. The computational programs developed are documented and are presented in a general user's manual which is included.

A Tangible Programming Tool for Children to Cultivate Computational Thinking

PubMed Central

Wang, Danli; Liu, Zhen

2014-01-01

Game and creation are activities which have good potential for computational thinking skills. In this paper we present T-Maze, an economical tangible programming tool for children aged 5–9 to build computer programs in maze games by placing wooden blocks. Through the use of computer vision technology, T-Maze provides a live programming interface with real-time graphical and voice feedback. We conducted a user study with 7 children using T-Maze to play two levels of maze-escape games and create their own mazes. The results show that T-Maze is not only easy to use, but also has the potential to help children cultivate computational thinking like abstraction, problem decomposition, and creativity. PMID:24719575

Supplement to the ICRPG turbulent boundary layer nozzle analysis computer program

NASA Technical Reports Server (NTRS)

Omori, S.; Gross, K. W.

1972-01-01

A supplement is presented for a turbulent boundary layer nozzle analysis computer program. It describes the program calculation sequence and presents a detailed documentation of each subroutine. Important equations are derived explicitly, and improvements to the program are discussed.

Human Memory Organization for Computer Programs.

ERIC Educational Resources Information Center

Norcio, A. F.; Kerst, Stephen M.

1983-01-01

Results of study investigating human memory organization in processing of computer programming languages indicate that algorithmic logic segments form a cognitive organizational structure in memory for programs. Statement indentation and internal program documentation did not enhance organizational process of recall of statements in five Fortran…

Index to Computer Assisted Instruction.

ERIC Educational Resources Information Center

Lekan, Helen A., Ed.

The computer assisted instruction (CAI) programs and projects described in this index are listed by subject matter. The index gives the program name, author, source, description, prerequisites, level of instruction, type of student, average completion time, logic and program, purpose for which program was designed, supplementary…

Computer program for calculating supersonic flow on the windward side conical delta wings by the method of lines

NASA Technical Reports Server (NTRS)

Klunker, E. B.; South, J. C., Jr.; Davis, R. M.

1972-01-01

A user's manual is presented for a program that calculates the supersonic flow on the windward side of conical delta wings with shock attached at the sharp leading edge by the method of lines. The program also has a limited capability for computing the flow about circular and elliptic cones at incidence. It provides information including the shock shape, flow field, isentropic surface-flow properties, and force coefficients. A description of the program operation, a sample computation, and a FORTRAN 4 program listing are included.

Computer viruses

NASA Technical Reports Server (NTRS)

Denning, Peter J.

1988-01-01

The worm, Trojan horse, bacterium, and virus are destructive programs that attack information stored in a computer's memory. Virus programs, which propagate by incorporating copies of themselves into other programs, are a growing menace in the late-1980s world of unprotected, networked workstations and personal computers. Limited immunity is offered by memory protection hardware, digitally authenticated object programs,and antibody programs that kill specific viruses. Additional immunity can be gained from the practice of digital hygiene, primarily the refusal to use software from untrusted sources. Full immunity requires attention in a social dimension, the accountability of programmers.

Computer Applications in Reading. Third Edition.

ERIC Educational Resources Information Center

Blanchard, Jay S.; And Others

Intended as a reference for researchers, teachers, and administrators, this book chronicles research, programs, and uses of computers in reading. Chapter 1 provides a broad view of computer applications in education, while Chapter 2 provides annotated references for computer based reading and language arts programs for children and adults in…

Seventy Years of Computing in the Nuclear Weapons Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Archer, Billy Joe

Los Alamos has continuously been on the forefront of scientific computing since it helped found the field. This talk will explore the rich history of computing in the Los Alamos weapons program. The current status of computing will be discussed, as will the expectations for the near future.

Learning about Tasks Computers Can Perform. ERIC Digest.

ERIC Educational Resources Information Center

Brosnan, Patricia A.

Knowing what different kinds of computer equipment can do is the first step in choosing the computer that is right for you. This digest describes a developmental progression of computer capabilities. First the basic three software programs (word processing, spreadsheets, and database programs) are discussed using examples. Next, an explanation of…

Your Career in Computer Programming.

ERIC Educational Resources Information Center

Seligsohn, I. J.

This book offers the career-minded young reader insight into computers and computer-programming, by describing the nature of the work, the actual workings of the machines, the language of computers, their history, and their far-reading and increasing applications in business, industry, science, education, defense, and government. At the same time,…

Project Logic Handbook: Computer Literacy through BASIC.

ERIC Educational Resources Information Center

Huber, Leonard; And Others

This handbook for teachers offers guidance on introducing computer literacy into elementary and secondary classrooms. It includes a list of computer concepts exemplified by each step in learning to write programs in BASIC Programming Language and the objectives for the elementary and secondary activities; suggestions for using computers in…

Computer-Assisted Language Learning: Current Programs and Projects. ERIC Digest.

ERIC Educational Resources Information Center

Higgins, Chris

For many years, foreign language teachers have used the computer to provide supplemental exercises in the instruction of foreign languages. In recent years, advances in computer technology have motivated teachers to reassess the computer and consider it a valuable part of daily foreign language learning. Innovative software programs, authoring…

75 FR 28252 - Notice of a Computer Matching Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-20

... GENERAL SERVICES ADMINISTRATION Notice of a Computer Matching Program AGENCY: General Services... providing notice of a proposed computer match. The purpose of this match is to identify individuals who are... providing notice of a proposed computer match. The purpose of this match is to identify individuals who are...

A computer program for analyzing channel geometry

USGS Publications Warehouse

Regan, R.S.; Schaffranek, R.W.

1985-01-01

The Channel Geometry Analysis Program (CGAP) provides the capability to process, analyze, and format cross-sectional data for input to flow/transport simulation models or other computational programs. CGAP allows for a variety of cross-sectional data input formats through use of variable format specification. The program accepts data from various computer media and provides for modification of machine-stored parameter values. CGAP has been devised to provide a rapid and efficient means of computing and analyzing the physical properties of an open-channel reach defined by a sequence of cross sections. CGAP 's 16 options provide a wide range of methods by which to analyze and depict a channel reach and its individual cross-sectional properties. The primary function of the program is to compute the area, width, wetted perimeter, and hydraulic radius of cross sections at successive increments of water surface elevation (stage) from data that consist of coordinate pairs of cross-channel distances and land surface or channel bottom elevations. Longitudinal rates-of-change of cross-sectional properties are also computed, as are the mean properties of a channel reach. Output products include tabular lists of cross-sectional area, channel width, wetted perimeter, hydraulic radius, average depth, and cross-sectional symmetry computed as functions of stage; plots of cross sections; plots of cross-sectional area and (or) channel width as functions of stage; tabular lists of cross-sectional area and channel width computed as functions of stage for subdivisions of a cross section; plots of cross sections in isometric projection; and plots of cross-sectional area at a fixed stage as a function of longitudinal distance along an open-channel reach. A Command Procedure Language program and Job Control Language procedure exist to facilitate program execution on the U.S. Geological Survey Prime and Amdahl computer systems respectively. (Lantz-PTT)

Preparing Students for Careers in Science and Industry with Computational Physics

NASA Astrophysics Data System (ADS)

Florinski, V. A.

2011-12-01

Funded by NSF CAREER grant, the University of Alabama (UAH) in Huntsville has launched a new graduate program in Computational Physics. It is universally accepted that today's physics is done on a computer. The program blends the boundary between physics and computer science by teaching student modern, practical techniques of solving difficult physics problems using diverse computational platforms. Currently consisting of two courses first offered in the Fall of 2011, the program will eventually include 5 courses covering methods for fluid dynamics, particle transport via stochastic methods, and hybrid and PIC plasma simulations. The UAH's unique location allows courses to be shaped through discussions with faculty, NASA/MSFC researchers and local R&D business representatives, i.e., potential employers of the program's graduates. Students currently participating in the program have all begun their research careers in space and plasma physics; many are presenting their research at this meeting.

Cloud-free resolution element statistics program

NASA Technical Reports Server (NTRS)

Liley, B.; Martin, C. D.

1971-01-01

Computer program computes number of cloud-free elements in field-of-view and percentage of total field-of-view occupied by clouds. Human error is eliminated by using visual estimation to compute cloud statistics from aerial photographs.

FAA computer security : recommendations to address continuing weaknesses

DOT National Transportation Integrated Search

2000-12-01

In September, testimony before the Committee on Science, House of Representatives, focused on the Federal Aviation Administration's (FAA) computer security program. In brief, we reported that FAA's agency-wide computer security program has serious, p...

What Is a Computer Program?

ERIC Educational Resources Information Center

Gemignani, Michael

1981-01-01

The concept of computer programs is discussed from many perspectives and shown to be many different things. The ambiguity of the term is reviewed in light of potential ramifications for computer specialists, attorneys, and the general public. (MP)

Bringing computational science to the public.

PubMed

McDonagh, James L; Barker, Daniel; Alderson, Rosanna G

2016-01-01

The increasing use of computers in science allows for the scientific analyses of large datasets at an increasing pace. We provided examples and interactive demonstrations at Dundee Science Centre as part of the 2015 Women in Science festival, to present aspects of computational science to the general public. We used low-cost Raspberry Pi computers to provide hands on experience in computer programming and demonstrated the application of computers to biology. Computer games were used as a means to introduce computers to younger visitors. The success of the event was evaluated by voluntary feedback forms completed by visitors, in conjunction with our own self-evaluation. This work builds on the original work of the 4273π bioinformatics education program of Barker et al. (2013, BMC Bioinform. 14:243). 4273π provides open source education materials in bioinformatics. This work looks at the potential to adapt similar materials for public engagement events. It appears, at least in our small sample of visitors (n = 13), that basic computational science can be conveyed to people of all ages by means of interactive demonstrations. Children as young as five were able to successfully edit simple computer programs with supervision. This was, in many cases, their first experience of computer programming. The feedback is predominantly positive, showing strong support for improving computational science education, but also included suggestions for improvement. Our conclusions are necessarily preliminary. However, feedback forms suggest methods were generally well received among the participants; "Easy to follow. Clear explanation" and "Very easy. Demonstrators were very informative." Our event, held at a local Science Centre in Dundee, demonstrates that computer games and programming activities suitable for young children can be performed alongside a more specialised and applied introduction to computational science for older visitors.

The Utah Educational Technology Initiative Year Two Evaluation: Program Implementation, Computer Acquisition and Placement, and Computer Use.

ERIC Educational Resources Information Center

Mergendoller, John R.; And Others

This evaluation report describes program implementation, computer acquisition and placement, and computer use during the second year (1991-92) of the Utah Educational Technology Initiative (ETI). In addition, it discusses the various ways computers are used in Utah schools and reports the opinions and experiences of ETI coordinators in the 12…

A Case Study of the Introduction of Computer Science in NZ Schools

ERIC Educational Resources Information Center

Bell, Tim; Andreae, Peter; Robins, Anthony

2014-01-01

For many years computing in New Zealand schools was focused on teaching students how to use computers, and there was little opportunity for students to learn about programming and computer science as formal subjects. In this article we review a series of initiatives that occurred from 2007 to 2009 that led to programming and computer science being…

The NASA computer science research program plan

NASA Technical Reports Server (NTRS)

1983-01-01

A taxonomy of computer science is included, one state of the art of each of the major computer science categories is summarized. A functional breakdown of NASA programs under Aeronautics R and D, space R and T, and institutional support is also included. These areas were assessed against the computer science categories. Concurrent processing, highly reliable computing, and information management are identified.

Overview 1993: Computational applications

NASA Technical Reports Server (NTRS)

Benek, John A.

1993-01-01

Computational applications include projects that apply or develop computationally intensive computer programs. Such programs typically require supercomputers to obtain solutions in a timely fashion. This report describes two CSTAR projects involving Computational Fluid Dynamics (CFD) technology. The first, the Parallel Processing Initiative, is a joint development effort and the second, the Chimera Technology Development, is a transfer of government developed technology to American industry.

Software for Building Models of 3D Objects via the Internet

NASA Technical Reports Server (NTRS)

Schramer, Tim; Jensen, Jeff

2003-01-01

The Virtual EDF Builder (where EDF signifies Electronic Development Fixture) is a computer program that facilitates the use of the Internet for building and displaying digital models of three-dimensional (3D) objects that ordinarily comprise assemblies of solid models created previously by use of computer-aided-design (CAD) programs. The Virtual EDF Builder resides on a Unix-based server computer. It is used in conjunction with a commercially available Web-based plug-in viewer program that runs on a client computer. The Virtual EDF Builder acts as a translator between the viewer program and a database stored on the server. The translation function includes the provision of uniform resource locator (URL) links to other Web-based computer systems and databases. The Virtual EDF builder can be used in two ways: (1) If the client computer is Unix-based, then it can assemble a model locally; the computational load is transferred from the server to the client computer. (2) Alternatively, the server can be made to build the model, in which case the server bears the computational load and the results are downloaded to the client computer or workstation upon completion.

Federal High Performance Computing and Communications Program. The Department of Energy Component.

ERIC Educational Resources Information Center

Department of Energy, Washington, DC. Office of Energy Research.

This report, profusely illustrated with color photographs and other graphics, elaborates on the Department of Energy (DOE) research program in High Performance Computing and Communications (HPCC). The DOE is one of seven agency programs within the Federal Research and Development Program working on HPCC. The DOE HPCC program emphasizes research in…

SNAP: A computer program for generating symbolic network functions

NASA Technical Reports Server (NTRS)

Lin, P. M.; Alderson, G. E.

1970-01-01

The computer program SNAP (symbolic network analysis program) generates symbolic network functions for networks containing R, L, and C type elements and all four types of controlled sources. The program is efficient with respect to program storage and execution time. A discussion of the basic algorithms is presented, together with user's and programmer's guides.

A Component-based Programming Model for Composite, Distributed Applications

NASA Technical Reports Server (NTRS)

Eidson, Thomas M.; Bushnell, Dennis M. (Technical Monitor)

2001-01-01

The nature of scientific programming is evolving to larger, composite applications that are composed of smaller element applications. These composite applications are more frequently being targeted for distributed, heterogeneous networks of computers. They are most likely programmed by a group of developers. Software component technology and computational frameworks are being proposed and developed to meet the programming requirements of these new applications. Historically, programming systems have had a hard time being accepted by the scientific programming community. In this paper, a programming model is outlined that attempts to organize the software component concepts and fundamental programming entities into programming abstractions that will be better understood by the application developers. The programming model is designed to support computational frameworks that manage many of the tedious programming details, but also that allow sufficient programmer control to design an accurate, high-performance application.

ORCA Project: Research on high-performance parallel computer programming environments. Final report, 1 Apr-31 Mar 90

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, L.; Notkin, D.; Adams, L.

1990-03-31

This task relates to research on programming massively parallel computers. Previous work on the Ensamble concept of programming was extended and investigation into nonshared memory models of parallel computation was undertaken. Previous work on the Ensamble concept defined a set of programming abstractions and was used to organize the programming task into three distinct levels; Composition of machine instruction, composition of processes, and composition of phases. It was applied to shared memory models of computations. During the present research period, these concepts were extended to nonshared memory models. During the present research period, one Ph D. thesis was completed, onemore » book chapter, and six conference proceedings were published.« less

Methods for evaluating and ranking transportation energy conservation programs

NASA Astrophysics Data System (ADS)

Santone, L. C.

1981-04-01

The energy conservation programs are assessed in terms of petroleum savings, incremental costs to consumers probability of technical and market success, and external impacts due to environmental, economic, and social factors. Three ranking functions and a policy matrix are used to evaluate the programs. The net present value measure which computes the present worth of petroleum savings less the present worth of costs is modified by dividing by the present value of DOE funding to obtain a net present value per program dollar. The comprehensive ranking function takes external impacts into account. Procedures are described for making computations of the ranking functions and the attributes that require computation. Computations are made for the electric vehicle, Stirling engine, gas turbine, and MPG mileage guide program.

A computer program for predicting nonlinear uniaxial material responses using viscoplastic models

NASA Technical Reports Server (NTRS)

Chang, T. Y.; Thompson, R. L.

1984-01-01

A computer program was developed for predicting nonlinear uniaxial material responses using viscoplastic constitutive models. Four specific models, i.e., those due to Miller, Walker, Krieg-Swearengen-Rhode, and Robinson, are included. Any other unified model is easily implemented into the program in the form of subroutines. Analysis features include stress-strain cycling, creep response, stress relaxation, thermomechanical fatigue loop, or any combination of these responses. An outline is given on the theoretical background of uniaxial constitutive models, analysis procedure, and numerical integration methods for solving the nonlinear constitutive equations. In addition, a discussion on the computer program implementation is also given. Finally, seven numerical examples are included to demonstrate the versatility of the computer program developed.

Air-to-Water Heat Pumps With Radiant Delivery in Low-Load Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Backman, C.; German, A.; Dakin, B.

2013-12-01

Space conditioning represents nearly 50% of average residential household energy consumption, highlighting the need to identify alternative cost-effective, energy-efficient cooling and heating strategies. As homes are better built, there is an increasing need for strategies that are particularly well suited for high performance, low load homes. ARBI researchers worked with two test homes in hot-dry climates to evaluate the in-situ performance of air-to-water heat pump (AWHP) systems, an energy efficient space conditioning solution designed to cost-effectively provide comfort in homes with efficient, safe, and durable operation. Two monitoring projects of test houses in hot-dry climates were initiated in 2010 tomore » test this system. Both systems were fully instrumented and have been monitored over one year to capture complete performance data over the cooling and heating seasons. Results are used to quantify energy savings, cost-effectiveness, and system performance using different operating modes and strategies. A calibrated TRNSYS model was developed and used to evaluate performance in various climate regions. This strategy is most effective in tight, insulated homes with high levels of thermal mass (i.e. exposed slab floors).« less

Building energy simulation in real time through an open standard interface

DOE PAGES

Pang, Xiufeng; Nouidui, Thierry S.; Wetter, Michael; ...

2015-10-20

Building energy models (BEMs) are typically used for design and code compliance for new buildings and in the renovation of existing buildings to predict energy use. We present the increasing adoption of BEM as standard practice in the building industry presents an opportunity to extend the use of BEMs into construction, commissioning and operation. In 2009, the authors developed a real-time simulation framework to execute an EnergyPlus model in real time to improve building operation. This paper reports an enhancement of that real-time energy simulation framework. The previous version only works with software tools that implement the custom co-simulation interfacemore » of the Building Controls Virtual Test Bed (BCVTB), such as EnergyPlus, Dymola and TRNSYS. The new version uses an open standard interface, the Functional Mockup Interface (FMI), to provide a generic interface to any application that supports the FMI protocol. In addition, the new version utilizes the Simple Measurement and Actuation Profile (sMAP) tool as the data acquisition system to acquire, store and present data. Lastly, this paper introduces the updated architecture of the real-time simulation framework using FMI and presents proof-of-concept demonstration results which validate the new framework.« less

Evaluation of spacecraft technology programs (effects on communication satellite business ventures), volume 2

NASA Technical Reports Server (NTRS)

Greenburg, J. S.; Kaplan, M.; Fishman, J.; Hopkins, C.

1985-01-01

The computational procedures used in the evaluation of spacecraft technology programs that impact upon commercial communication satellite operations are discussed. Computer programs and data bases are described.

Basis And Application Of The CARES/LIFE Computer Program

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.; Janosik, Lesley A.; Gyekenyesi, John P.; Powers, Lynn M.

1996-01-01

Report discusses physical and mathematical basis of Ceramics Analysis and Reliability Evaluation of Structures LIFE prediction (CARES/LIFE) computer program, described in "Program for Evaluation of Reliability of Ceramic Parts" (LEW-16018).

An Analysis on Distance Education Computer Programming Students' Attitudes Regarding Programming and Their Self-Efficacy for Programming

ERIC Educational Resources Information Center

Ozyurt, Ozcan

2015-01-01

This study aims to analyze the attitudes of students studying computer programming through the distance education regarding programming, and their self-efficacy for programming and the relation between these two factors. The study is conducted with 104 students being thought with distance education in a university in the north region of Turkey in…

Description of CASCOMP Comprehensive Airship Sizing and Performance Computer Program, Volume 2

NASA Technical Reports Server (NTRS)

Davis, J.

1975-01-01

The computer program CASCOMP, which may be used in comparative design studies of lighter than air vehicles by rapidly providing airship size and mission performance data, was prepared and documented. The program can be used to define design requirements such as weight breakdown, required propulsive power, and physical dimensions of airships which are designed to meet specified mission requirements. The program is also useful in sensitivity studies involving both design trade-offs and performance trade-offs. The input to the program primarily consists of a series of single point values such as hull overall fineness ratio, number of engines, airship hull and empennage drag coefficients, description of the mission profile, and weights of fixed equipment, fixed useful load and payload. In order to minimize computation time, the program makes ample use of optional computation paths.

A two-dimensional graphing program for the Tektronix 4050-series graphics computers

USGS Publications Warehouse

Kipp, K.L.

1983-01-01

A refined, two-dimensional graph-plotting program was developed for use on Tektronix 4050-series graphics computers. Important features of this program include: any combination of logarithmic and linear axes, optional automatic scaling and numbering of the axes, multiple-curve plots, character or drawn symbol-point plotting, optional cartridge-tape data input and plot-format storage, optional spline fitting for smooth curves, and built-in data-editing options. The program is run while the Tektronix is not connected to any large auxiliary computer, although data from files on an auxiliary computer easily can be transferred to data-cartridge for later plotting. The user is led through the plot-construction process by a series of questions and requests for data input. Five example plots are presented to illustrate program capability and the sequence of program operation. (USGS)

Engineering and programming manual: Two-dimensional kinetic reference computer program (TDK)

NASA Technical Reports Server (NTRS)

Nickerson, G. R.; Dang, L. D.; Coats, D. E.

1985-01-01

The Two Dimensional Kinetics (TDK) computer program is a primary tool in applying the JANNAF liquid rocket thrust chamber performance prediction methodology. The development of a methodology that includes all aspects of rocket engine performance from analytical calculation to test measurements, that is physically accurate and consistent, and that serves as an industry and government reference is presented. Recent interest in rocket engines that operate at high expansion ratio, such as most Orbit Transfer Vehicle (OTV) engine designs, has required an extension of the analytical methods used by the TDK computer program. Thus, the version of TDK that is described in this manual is in many respects different from the 1973 version of the program. This new material reflects the new capabilities of the TDK computer program, the most important of which are described.

Planetary quarantine computer applications

NASA Technical Reports Server (NTRS)

Rafenstein, M.

1973-01-01

The computer programs are identified pertaining to planetary quarantine activities within the Project Engineering Division, both at the Air Force Eastern Test Range and on site at the Jet Propulsion Laboratory. A brief description of each program and program inputs are given and typical program outputs are shown.

Computer Assistance for Writing Interactive Programs: TICS.

ERIC Educational Resources Information Center

Kaplow, Roy; And Others

1973-01-01

Investigators developed an on-line, interactive programing system--the Teacher-Interactive Computer System (TICS)--to provide assistance to those who were not programers, but nevertheless wished to write interactive instructional programs. TICS had two components: an author system and a delivery system. Underlying assumptions were that…

Frequency Domain Computer Programs for Prediction and Analysis of Rail Vehicle Dynamics : Volume 2. Appendixes

DOT National Transportation Integrated Search

1975-12-01

Frequency domain computer programs developed or acquired by TSC for the analysis of rail vehicle dynamics are described in two volumes. Volume 2 contains program listings including subroutines for the four TSC frequency domain programs described in V...

Teaching Machines, Programming, Computers, and Instructional Technology: The Roots of Performance Technology.

ERIC Educational Resources Information Center

Deutsch, William

1992-01-01

Reviews the history of the development of the field of performance technology. Highlights include early teaching machines, instructional technology, learning theory, programed instruction, the systems approach, needs assessment, branching versus linear program formats, programing languages, and computer-assisted instruction. (LRW)

ASC FY17 Implementation Plan, Rev. 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamilton, P. G.

The Stockpile Stewardship Program (SSP) is an integrated technical program for maintaining the safety, surety, and reliability of the U.S. nuclear stockpile. The SSP uses nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of experimental facilities and programs, and the computational capabilities to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities and computationalmore » resources that support annual stockpile assessment and certification, study advanced nuclear weapons design and manufacturing processes, analyze accident scenarios and weapons aging, and provide the tools to enable stockpile Life Extension Programs (LEPs) and the resolution of Significant Finding Investigations (SFIs). This requires a balance of resources, including technical staff, hardware, simulation software, and computer science solutions.« less

Space shuttle atmospheric revitalization subsystem/active thermal control subsystem computer program (users manual)

NASA Technical Reports Server (NTRS)

1973-01-01

A shuttle (ARS) atmosphere revitalization subsystem active thermal control subsystem (ATCS) performance routine was developed. This computer program is adapted from the Shuttle EC/LSS Design Computer Program. The program was upgraded in three noteworthy areas: (1) The functional ARS/ATCS schematic has been revised to accurately synthesize the shuttle baseline system definition. (2) The program logic has been improved to provide a more accurate prediction of the integrated ARS/ATCS system performance. Additionally, the logic has been expanded to model all components and thermal loads in the ARS/ATCS system. (3) The program is designed to be used on the NASA JSC crew system division's programmable calculator system. As written the new computer routine has an average running time of five minutes. The use of desk top type calculation equipment, and the rapid response of the program provides the NASA with an analytical tool for trade studies to refine the system definition, and for test support of the RSECS or integrated Shuttle ARS/ATCS test programs.

An analytical procedure and automated computer code used to design model nozzles which meet MSFC base pressure similarity parameter criteria. [space shuttle

NASA Technical Reports Server (NTRS)

Sulyma, P. R.

1980-01-01

Fundamental equations and similarity definition and application are described as well as the computational steps of a computer program developed to design model nozzles for wind tunnel tests conducted to define power-on aerodynamic characteristics of the space shuttle over a range of ascent trajectory conditions. The computer code capabilities, a user's guide for the model nozzle design program, and the output format are examined. A program listing is included.

Medical education as a science: the quality of evidence for computer-assisted instruction.

PubMed

Letterie, Gerard S

2003-03-01

A marked increase in the number of computer programs for computer-assisted instruction in the medical sciences has occurred over the past 10 years. The quality of both the programs and the literature that describe these programs has varied considerably. The purposes of this study were to evaluate the published literature that described computer-assisted instruction in medical education and to assess the quality of evidence for its implementation, with particular emphasis on obstetrics and gynecology. Reports published between 1988 and 2000 on computer-assisted instruction in medical education were identified through a search of MEDLINE and Educational Resource Identification Center and a review of the bibliographies of the articles that were identified. Studies were selected if they included a description of computer-assisted instruction in medical education, regardless of the type of computer program. Data were extracted with a content analysis of 210 reports. The reports were categorized according to study design (comparative, prospective, descriptive, review, or editorial), type of computer-assisted instruction, medical specialty, and measures of effectiveness. Computer-assisted instruction programs included online technologies, CD-ROMs, video laser disks, multimedia work stations, virtual reality, and simulation testing. Studies were identified in all medical specialties, with a preponderance in internal medicine, general surgery, radiology, obstetrics and gynecology, pediatrics, and pathology. Ninety-six percent of the articles described a favorable impact of computer-assisted instruction in medical education, regardless of the quality of the evidence. Of the 210 reports that were identified, 60% were noncomparative, descriptive reports of new techniques in computer-assisted instruction, and 15% and 14% were reviews and editorials, respectively, of existing technology. Eleven percent of studies were comparative and included some form of assessment of the effectiveness of the computer program. These assessments included pre- and posttesting and questionnaires to score program quality, perceptions of the medical students and/or residents regarding the program, and impact on learning. In one half of these comparative studies, computer-assisted instruction was compared with traditional modes of teaching, such as text and lectures. Six studies compared performance before and after the computer-assisted instruction. Improvements were shown in 5 of the studies. In the remainder of the studies, computer-assisted instruction appeared to result in similar test performance. Despite study design or outcome, most articles described enthusiastic endorsement of the programs by the participants, including medical students, residents, and practicing physicians. Only 1 study included cost analysis. Thirteen of the articles were in obstetrics and gynecology. Computer-assisted instruction has assumed to have an increasing role in medical education. In spite of enthusiastic endorsement and continued improvements in software, few studies of good design clearly demonstrate improvement in medical education over traditional modalities. There are no comparative studies in obstetrics and gynecology that demonstrate a clear-cut advantage. Future studies of computer-assisted instruction that include comparisons and cost assessments to gauge their effectiveness over traditional methods may better define their precise role.