Thermally and optically stimulated radiative processes in Eu and Y co-doped LiCaAlF6 crystal

NASA Astrophysics Data System (ADS)

Fukuda, Kentaro; Yanagida, Takayuki; Fujimoto, Yutaka

2015-06-01

Yttrium co-doping was attempted to enhance dosimeter performance of Eu doped LiCaAlF6 crystal. Eu doped and Eu, Y co-doped LiCaAlF6 were prepared by the micro-pulling-down technique, and their dosimeter characteristics such as optically stimulated luminescence (OSL) and thermally stimulated luminescence (TSL) were investigated. By yttrium co-doping, emission intensities of OSL and TSL were enhanced by some orders of magnitude. In contrast, scintillation characteristics of yttrium co-doped crystal such as intensity of prompt luminescence induced by X-ray and light yield under neutron irradiation were degraded.

Creep behaviour of a polymer-based underground support liner

NASA Astrophysics Data System (ADS)

Guner, Dogukan; Ozturk, Hasan

2017-09-01

All underground excavations (tunnels, mines, caverns, etc.) need a form of support to ensure that excavations remain safe and stable for the designed service lifetime. In the last decade, a new support material, thin spray-on liner (TSL) has started to take place of traditional underground surface supports of bolts and shotcrete. TSLs are generally cement, latex, polymer-based and also reactive or non-reactive, multi-component materials applied to the rock surface with a layer of few millimeter thickness. They have the advantages of low volume, logistics, rapid application and low operating cost. The majority of current TSLs are two-part products that are mixed on site before spraying onto excavation rock surfaces. Contrary to the traditional brittle supports, the high plastic behaviour of TSLs make them to distribute the loads on larger lining area. In literature, there is a very limited information exist on the creep behavior of TSLs. In this study, the creep behavior of a polymer-based TSL was investigated. For this purpose, 7-day cured dogbone TSL specimens were tested under room temperature and humidity conditions according to ASTM-D2990 creep testing standard. A range of dead weights (80, 60, 40, and 20 % of the tensile strength) were applied up to 1500 hours. As a result of this study, the time-dependent strain behavior of a TSL was presented for different constant load conditions. Moreover, a new equation was derived to estimate tensile failure time of the TSL for a given loading condition. If the tensile stress acting on the TSL is known, the effective permanent support time of the TSL can be estimated by the proposed relationship.

Multi-muscle electrical stimulation and stand training: Effects on standing.

PubMed

Momeni, Kamyar; Ramanujam, Arvind; Garbarini, Erica L; Forrest, Gail F

2018-02-15

To examine the biomechanical and neuromuscular effects of a longitudinal multi-muscle electrical stimulation (submaximal intensities) training of the lower limbs combined with/without activity-based stand training, on the recovery of stability and function for one individual with spinal cord injury (SCI). Single-subject, longitudinal study. Neuroplasticity laboratory. A 34-year-old male, with sensory- and motor-complete SCI (C5/C6). Two consecutive interventions: 61 hours of supine, lower-limb ES (ES-alone) and 51 hours of ES combined with stand training using an overhead body-weight support system (ST + ES). Clinical measures, trunk stability, and muscle activity were assessed and compared across time points. Trunk Stability Limit (TSL) determined improvements in trunk independence. Functional clinical values increased after both interventions, with further increases post ST + ES. Post ES-alone, trunk stability was maintained at 81% body-weight (BW) loading before failure; post ST + ES, BW loading increased to 95%. TSL values decreased post ST + ES (TSL A/P =54.0 kg.cm, TSL M/L =14.5 kg.cm), compared to ES-alone (TSL A/P =8.5 kg.cm, TSL M/L =3.9 kg.cm). Trunk muscle activity decreased post ST + ES training, compared to ES-alone. Neuromuscular and postural trunk control dramatically improved following the multi-muscle ES of the lower limbs with stand training. Multi-muscle ES training paradigm of the lower limb, using traditional parameters, may contribute to the functional recovery of the trunk.

Relative Humidity in the Tropopause Saturation Layer

NASA Astrophysics Data System (ADS)

Selkirk, H. B.; Schoeberl, M. R.; Pfister, L.; Thornberry, T. D.; Bui, T. V.

2017-12-01

The tropical tropopause separates two very different atmospheric regimes: the stable lower stratosphere where the air is both extremely dry and nearly always so, and a transition layer in the uppermost tropical troposphere, where humidity on average increases rapidly downward but can undergo substantial temporal fluctuations. The processes that control the humidity in this layer below the tropopause include convective detrainment (which can result in either a net hydration or dehydration), slow ascent, wave motions and advection. Together these determine the humidity of the air that eventually passes through the tropopause and into the stratosphere, and we refer to this layer as the tropopause saturation layer or TSL. We know from in situ water vapor observations such as Ticosonde's 12-year balloonsonde record at Costa Rica that layers of supersaturation are frequently observed in the TSL. While their frequency is greatest during the local rainy season from June through October, supersaturation is also observed in the boreal winter dry season when deep convection is well south of Costa Rica. In other words, local convection is not a necessary condition for the presence of supersaturation. Furthermore, there are indications from airborne measurements during the recent POSIDON campaign at Guam that if anything deep convection tends to `reset' the TSL locally to a state of just-saturation. Conversely, it may be that layers of supersaturation are the result of slow ascent. To explore these ideas we take Ticosonde water vapor observations from the TSL, stratify them on the basis of relative humidity and report on the differences in the the history of upstream convective influence between supersaturated parcels and those that are not.

Phase 2 study of treatment selection based on tumor thymidylate synthase expression in previously untreated patients with metastatic colorectal cancer: A trial of the ECOG-ACRIN Cancer Research Group (E4203).

PubMed

Meropol, Neal J; Feng, Yang; Grem, Jean L; Mulcahy, Mary F; Catalano, Paul J; Kauh, John S; Hall, Michael J; Saltzman, Joel N; George, Thomas J; Zangmeister, Jeffrey; Chiorean, Elena G; Cheema, Puneet S; O'Dwyer, Peter J; Benson, Al B

2018-02-15

The authors hypothesized that patients with metastatic colorectal cancer (mCRC) who had tumors with low thymidylate synthase (TS-L) expression would have a higher response rate to combined 5-fluorouracil, leucovorin, and oxaliplatin (FOLFOX) plus bevacizumab (FOLFOX/Bev) than those with high TS (TS-H) expression and that combined irinotecan and oxaliplatin (IROX) plus bevacizumab (IROX/Bev) would be more effective than FOLFOX/Bev in those with TS-H tumors. TS protein expression was determined in mCRC tissue. Patients who had TS-L tumors received FOLFOX/Bev, and those who had TS-H tumors were randomly assigned to receive either FOLFOX/Bev or IROX/Bev. The primary endpoint was the response rate (complete plus partial responses). In total, 211 of 247 patients (70% TS-H) were registered to the treatment phase. Efficacy analyses included eligible patients who had started treatment (N = 186). The response rates for patients who received IROX/Bev (TS-H), FOLFOX/Bev (TS-H), and FOLFOX/Bev (TS-L) were 33%, 38%, and 49%, respectively (P = nonsignificant). The median progression-free survival (PFS) was 10 months (95% confidence interval [CI], 9-12 months; 10 months in the IROX/Bev TS-H group, 9 months in the FOLFOX/Bev TS-H group, and 13 months in the FOLFOX/Bev TS-L group). The TS-L group had improved PFS compared with the TS-H group that received FOLFOX/Bev (hazard ratio, 1.6; 95% CI, 1.0%-2.4%; P = .04; Cox regression). The median overall survival (OS) was 22 months (95% CI, 20 29 months; 18 months in the IROX/Bev TS-H group, 21 months in the FOLFOX/Bev TS-H group, and 32 months in the TS-L group). OS comparisons for the 2 TS-H arms and for the FOLFOX/Bev TS-H versus TS-L arms were not significantly different. TS expression was prognostic: Patients with TS-L tumors who received FOLFOX/Bev had a longer PFS than those with TS-H tumors, along with a trend toward longer OS. Patients with TS-H tumors did not benefit more from IROX/Bev than from FOLFOX/Bev. Cancer 2018;124:688-97. © 2017 American Cancer Society. © 2017 American Cancer Society.

Rehabilitation of molar-incisor hypomineralization (MIH) complicated with localized tooth surface loss: a case report.

PubMed

Lam, Walter Y H; Ho, Edward H T; Pow, Edmond H N

2014-05-01

Molar-incisor hypomineralization (MIH) is a developmental enamel hypomineralized condition characteristically involving the first permanent molars and sometimes also the incisors. The affected teeth are predisposed to tooth surface loss (TSL) which may not only compromise the esthetics and function but also endanger the pulp and longevity of the teeth. This report describes the management of a patient with MIH complicated with localized TSL and lack of occlusal clearance due to dentoalveolar compensation. The atypical TSL pattern involved all anterior teeth and required the placement of Dahl appliances on both arches.

Chemopreventive effect of Toona sinensis leaf extract on 7,12-dimethylbenz[a]anthracene-induced hamster buccal pouch squamous cell carcinogenesis.

PubMed

Wang, Wen-Chen; Chen, Ching-Yi; Hsu, Hseng-Kuang; Lin, Li-Min; Chen, Yuk-Kwan

2016-10-01

Toona sinensis leaf extract (TSL) has been shown to have anti-tumor effects on cancer cell lines. This study aimed to investigate the chemopreventive potential and the underlying mechanism of TSL during 7,12-dimethylbenz[a]anthracene (DMBA)-induced hamster buccal pouch (HBP) carcinogenesis. One hundred hamsters were divided into control (n=30), carcinogenic (n=20), preventive (n=42), and therapeutic (n=8) groups. The animals in carcinogenic and preventive groups were administered reverse osmosis water (carcinogenic group) or TSL (1g/kg bw) (preventive group) by gavage daily for 4 weeks, and their bilateral pouches were painted with a 0.5% DMBA solution for 4, 9, and 12 weeks. The animals in the therapeutic group were treated with DMBA for 12 weeks prior to TSL administration for 4 weeks. Expression levels of survivin, X chromosome-linked inhibitor of apoptosis (XIAP), proliferating cell nuclear antigen (PCNA), inducible nitric oxide synthase (iNOS), and cyclooxygenase-2 (COX-2) proteins were analyzed by immunohistochemistry. Apoptotic activity was examined by terminal deoxynucleotidyl transferase dUTP nick end labeling (TUNEL) method, cytochrome C, and poly (ADP-ribose) polymerase (PARP). In the preventive group, the results showed significant decreases not only in the incidences of squamous cell carcinoma (SCC) (50%) and epithelial dysplasia (62.5%) but also in the tumor number, tumor volume, tumor burden, and the severity of dysplastic lesions. The down-regulation of survivin, XIAP, PCNA, iNOS, and COX-2 proteins and the increased apoptotic activity indicated anti-proliferative and apoptosis-inducing abilities of TSL on DMBA-induced HBP carcinogenesis. The results suggested that TSL might be a promising candidate for the prevention of oral cancer. Copyright © 2016 Elsevier Ltd. All rights reserved.

Screening of fluoroquinolone residues in caprine milk using a 5-kg luminescence photometer

USDA-ARS?s Scientific Manuscript database

A terbium-sensitized luminescence (TSL) method was developed to screen presence of residues of four fluoroquinolones (FQ) registered in caprine milk in the European Union: enrofloxacin, ciprofloxacin, flumequine, and danofloxacin. After extraction in McIlvaine buffer and SPE cleanup, TSL was measure...

Sustained 35-GHz radiofrequency irradiation induces circulatory failure.

PubMed

Frei, M R; Ryan, K L; Berger, R E; Jauchem, J R

1995-10-01

The objective of this study was to determine the thermal distribution and concomitant cardiovascular changes produced by whole-body exposure of ketamine-anesthetized rats to radiofrequency radiation of millimeter wave (MMW) length. Rats (n = 13) were implanted with a flow probe on the superior mesenteric artery and with a catheter in the carotid artery for the measurement of arterial blood pressure. Temperature was measured at five sites: left (Tsl) and right subcutaneous (sides toward and away From the MMW source, respectively), colonic (Tc), tympanic, and tail. The animals were exposed until death to MMW (35 GHz) at a power density that resulted in a whole-body specific absorption rate of 13 W/kg. During irradiation, the Tsl increase was significantly greater than the Tc increase. Heart rate increased throughout irradiation. Mean arterial pressure (MAP) as well maintained until Tsl reached 42 degrees C, at which point MAP declined until death. Mesenteric vascular resistance tended to increase during the early stages of irradiation but began to decrease at Tsl > or = 41 degrees C. The declines in both mesenteric vascular resistance and MAP began at Tc < 37.5 degrees C; death occurred at Tc = 40.3 +/- .3 degrees C and Tsl = 48.0 +/- .4 degrees C. These data indicate that circulatory failure and subsequent death may occur when skin temperature is rapidly elevated, even in the presence of relatively normal Tc.

Targeting RNA structure in SMN2 reverses spinal muscular atrophy molecular phenotypes.

PubMed

Garcia-Lopez, Amparo; Tessaro, Francesca; Jonker, Hendrik R A; Wacker, Anna; Richter, Christian; Comte, Arnaud; Berntenis, Nikolaos; Schmucki, Roland; Hatje, Klas; Petermann, Olivier; Chiriano, Gianpaolo; Perozzo, Remo; Sciarra, Daniel; Konieczny, Piotr; Faustino, Ignacio; Fournet, Guy; Orozco, Modesto; Artero, Ruben; Metzger, Friedrich; Ebeling, Martin; Goekjian, Peter; Joseph, Benoît; Schwalbe, Harald; Scapozza, Leonardo

2018-05-23

Modification of SMN2 exon 7 (E7) splicing is a validated therapeutic strategy against spinal muscular atrophy (SMA). However, a target-based approach to identify small-molecule E7 splicing modifiers has not been attempted, which could reveal novel therapies with improved mechanistic insight. Here, we chose as a target the stem-loop RNA structure TSL2, which overlaps with the 5' splicing site of E7. A small-molecule TSL2-binding compound, homocarbonyltopsentin (PK4C9), was identified that increases E7 splicing to therapeutic levels and rescues downstream molecular alterations in SMA cells. High-resolution NMR combined with molecular modelling revealed that PK4C9 binds to pentaloop conformations of TSL2 and promotes a shift to triloop conformations that display enhanced E7 splicing. Collectively, our study validates TSL2 as a target for small-molecule drug discovery in SMA, identifies a novel mechanism of action for an E7 splicing modifier, and sets a precedent for other splicing-mediated diseases where RNA structure could be similarly targeted.

Thermally stimulated luminescence properties of BaY2F8 : Ce crystals

NASA Astrophysics Data System (ADS)

Vedda, A.; Martini, M.; di Martino, D.; Sani, E.; Toncelli, A.; Tonelli, M.

Wavelength resolved thermally stimulated luminescence (TSL) measurements were performed on BaY2 F-8 :1.8 mol% Ce crystals after X-ray irradiation at 10 K and at 300 K, in order to obtain preliminary information about both trap levels and recombination centres. After irradiation at 10 K, the TSL glow curve shows the presence of a strong peak at 50 K, together with additional structures at approximately 20 and 170 K. The TSL spectrum is dominated by the characteristic doublet emission due to transitions from the lowest energy level of the 5d configuration to the spin-orbit split F-2 ground state of Ce3+ . Above RT, the glow curve exhibits a peak at 60 degreesC, whose spectrum is again dominated by Ce3+ emission. The TSL emission is in accordance with radio-luminescence (RL) spectra performed in the 10-300 K region. Moreover, RL spectra at temperatures lower than 200 K display an additional weak high energy band at around 4.5 eV assigned to host lattice transitions.

Effect of heating rate on kinetic parameters of β-irradiated Li2B4O7:Cu,Ag,P in TSL measurements

NASA Astrophysics Data System (ADS)

Türkler Ege, A.; Ekdal, E.; Karali, T.; Can, N.; Prokic, M.

2007-03-01

The effect of heating rate on the thermally stimulated luminescence (TSL) emission due to the temperature lag (TLA) between the TSL material and the heating element has been investigated using Li2B4O7:Cu,Ag,P dosimetric materials. The TLA becomes significant when the material is heated at high heating rates. TSL glow curves of Li2B4O7:Cu,Ag,P material showed two main peaks after β-irradiation. The kinetic parameters, namely activation energy (E) and frequency factor (s) associated with the high temperature main peak of Li2B4O7:Cu,Ag,P were determined using the method of various heating rates (VHR), in which heating rates from 1 to 40 K s-1 were used. It is assumed that non-ideal heat transfer between the heater and the material may cause significant inconsistency of kinetic parameter values obtained with different methods. The effect of TLA on kinetic parameters of the dosimeter was examined.

"Thank You, Sorry, Love" (TSL) Therapy with North Korean Refugee Women: A Pilot Study

ERIC Educational Resources Information Center

Kim, Hee Jin; Kim, Jae Yop; Kim, Dong Goo

2016-01-01

Objectives: This study was designed to evaluate the effectiveness of The "Thank You, Sorry, Love" (TSL) family therapy program in potentially improving the marital relationships and health of North Korean refugee women. Methods: The participants included 12 married North Korean female refugees in their 20s to 40s. Using a blinded…

Screening of Danofloxacin residue in bovine tissue by terbium-sensitized luminescence on C18 sorbent strips

USDA-ARS?s Scientific Manuscript database

Danofloxacin (DANO) residue in bovine muscle was screened at 200 ng/g by terbium-sensitized luminescence (TSL) directly measured on 10x6 mm C18 sorbent strips. The analyte was first adsorbed on sorbent surface by immersion in defatted homogenates. After reagent application and desiccation, TSL was d...

The Nature and Effects of Transformational School Leadership: A Meta-Analytic Review of Unpublished Research

ERIC Educational Resources Information Center

Leithwood, Kenneth; Sun, Jingping

2012-01-01

Background: Using meta-analytic review techniques, this study synthesized the results of 79 unpublished studies about the nature of transformational school leadership (TSL) and its impact on the school organization, teachers, and students. This corpus of research associates TSL with 11 specific leadership practices. These practices, as a whole,…

Growth of InAs/InP core-shell nanowires with various pure crystal structures.

PubMed

Gorji Ghalamestani, Sepideh; Heurlin, Magnus; Wernersson, Lars-Erik; Lehmann, Sebastian; Dick, Kimberly A

2012-07-20

We have studied the epitaxial growth of an InP shell on various pure InAs core nanowire crystal structures by metal-organic vapor phase epitaxy. The InP shell is grown on wurtzite (WZ), zinc-blende (ZB), and {111}- and {110}-type faceted ZB twin-plane superlattice (TSL) structures by tuning the InP shell growth parameters and controlling the shell thickness. The growth results, particularly on the WZ nanowires, show that homogeneous InP shell growth is promoted at relatively high temperatures (∼500 °C), but that the InAs nanowires decompose under the applied conditions. In order to protect the InAs core nanowires from decomposition, a short protective InP segment is first grown axially at lower temperatures (420-460 °C), before commencing the radial growth at a higher temperature. Further studies revealed that the InP radial growth rate is significantly higher on the ZB and TSL nanowires compared to WZ counterparts, and shows a strong anisotropy in polar directions. As a result, thin shells were obtained during low temperature InP growth on ZB structures, while a higher temperature was used to obtain uniform thick shells. In addition, a schematic growth model is suggested to explain the basic processes occurring during the shell growth on the TSL crystal structures.

Tensile-Creep Test Specimen Preparation Practices of Surface Support Liners

NASA Astrophysics Data System (ADS)

Guner, Dogukan; Ozturk, Hasan

2017-12-01

Ground support has always been considered as a challenging issue in all underground operations. Many forms of support systems and supporting techniques are available in the mining/tunnelling industry. In the last two decades, a new polymer based material, Thin Spray-on Liner (TSL), has attained a place in the market as an alternative to the current areal ground support systems. Although TSL provides numerous merits and has different application purposes, the knowledge on mechanical properties and performance of this material is still limited. In laboratory studies, since tensile rupture is the most commonly observed failure mechanism in field applications, researchers have generally studied the tensile testing of TSLs with modification of American Society for Testing and Materials (ASTM) D-638 standards. For tensile creep testing, specimen preparation process also follows the ASTM standards. Two different specimen dimension types (Type I, Type IV) are widely preferred in TSL tensile testing that conform to the related standards. Moreover, molding and die cutting are commonly used specimen preparation techniques. In literature, there is a great variability of test results due to the difference in specimen preparation techniques and practices. In this study, a ductile TSL product was tested in order to investigate the effect of both specimen preparation techniques and specimen dimensions under 7-day curing time. As a result, ultimate tensile strength, tensile yield strength, tensile modulus, and elongation at break values were obtained for 4 different test series. It is concluded that Type IV specimens have higher strength values compared to Type I specimens and moulded specimens have lower results than that of prepared by using die cutter. Moreover, specimens prepared by molding techniques have scattered test results. Type IV specimens prepared by die cutter technique are suggested for preparation of tensile test and Type I specimens prepared by die cutter technique should be preferred for tensile creep tests.

Gemcitabine treatment of rat soft tissue sarcoma with phosphatidyldiglycerol-based thermosensitive liposomes.

PubMed

Limmer, Simone; Hahn, Jasmin; Schmidt, Rebecca; Wachholz, Kirsten; Zengerle, Anja; Lechner, Katharina; Eibl, Hansjörg; Issels, Rolf D; Hossann, Martin; Lindner, Lars H

2014-09-01

The pyrimidine analogue gemcitabine (dFdC) is frequently used in the treatment of patients with solid tumors. However, after i.v. application dFdC is rapidly inactivated by metabolization. Here, the potential of thermosensitive liposomes based on 1,2-dipalmitoyl-sn-glycero-3-phosphodiglycerol (DPPG2-TSL) were investigated as carrier and targeting system for delivery of dFdC in combination with local hyperthermia (HT). DPPG2-TSL were prepared by the lipid film hydration and extrusion method and characterized by dynamic light scattering, thin layer chromatography, phosphate assay and HPLC. In vivo experiments were performed in Brown Norway rats with a syngeneic soft tissue sarcoma. Local HT treatment was performed by light exposure. DPPG2-TSL were stable at 37°C in serum and showed a temperature dependent dFdC release >40°C. Plasma half-life of dFdC was strongly increased from 0.07 h (non-liposomal) to 0.53 h (liposomal, vesicle size 105 nm) or 2.59 h (liposomal, 129 nm). Therapy of BN175 tumors with dFdC encapsulated in DPPG2-TSL + HT showed significant improvement in tumor growth delay compared to non-liposomal dFdC without HT (p < 0.05), non-liposomal dFdC with HT (p < 0.01), and liposomal dFdC without HT (p < 0.05), respectively. Gemcitabine encapsulated in DPPG2-TSL in combination with local HT is a promising tool for the treatment of solid tumors. Therefore, these encouraging results ask for further investigation and evaluation.

TSL Family Therapy Followed by Improved Marital Quality and Reduced Oxidative Stress

ERIC Educational Resources Information Center

Kim, Jae Yop; Kim, Dong Goo; Nam, Seok In

2012-01-01

Objectives: The current study evaluated the effectiveness of a form of family therapy developed in Korea. The "Thank you--Sorry--Love" (TSL) model was applied to a group of elderly retired men to improve the quality of their marriage and to reduce their stress. Methods: Thirty married retired Korean men were assigned to three groups.…

Method of hyperthermia and tumor size influence effectiveness of doxorubicin release from thermosensitive liposomes in experimental tumors.

PubMed

Willerding, Linus; Limmer, Simone; Hossann, Martin; Zengerle, Anja; Wachholz, Kirsten; Ten Hagen, Timo L M; Koning, Gerben A; Sroka, Ronald; Lindner, Lars H; Peller, Michael

2016-01-28

Systemic chemotherapy of solid tumors could be enhanced by local hyperthermia (HT) in combination with thermosensitive liposomes (TSL) as drug carriers. In such an approach, effective HT of the tumor is considered essential for successful triggering local drug release and targeting of the drug to the tumor. To investigate the effect of HT method on the effectiveness of drug delivery, a novel laser-based HT device designed for the use in magnetic resonance imaging (MRI) was compared systematically with the frequently used cold light lamp and water bath HT. Long circulating phosphatidyldiglycerol-based TSL (DPPG2-TSL) with encapsulated doxorubicin (DOX) were used as drug carrier enabling intravascular drug release. Experiments were performed in male Brown Norway rats with a syngeneic soft tissue sarcoma (BN 175) located on both hind legs. One tumor was heated while the second tumor remained unheated as a reference. Six animals were investigated per HT method. DPPG2-TSL were injected i.v. at a stable tumor temperature above 40°C. Thereafter, temperature was maintained for 60min. Total DOX concentration in plasma, tumor tissue and muscle was determined post therapy by HPLC. Finally, the new laser-based device was tested in a MRI environment at 3T using DPPG2-TSL with encapsulated Gd-based contrast agent. All methods showed effective DOX delivery by TSL with 4.5-23.1ng/mg found in the heated tumors. In contrast, DOX concentration in the non-heated tumors was 0.5±0.1ng/mg. Independent of used HT methods, higher DOX levels were found in the smaller tumors. In comparison water bath induced lowest DOX delivery but still showing fourfold higher DOX concentrations compared to the non-heated tumors. With the laser-based applicator, a 13 fold higher DOX deposition was possible for large tumors and a 15 fold higher for the small tumors, respectively. Temperature gradients in the tumor tissue were higher with the laser and cold light lamp (-0.3°C/mm to -0.5°C/mm) compared to the water bath (-0.1°C/mm and -0.2°C/mm). Visualization of HT in the MRI demonstrated successful localized heating throughout the entire tumor volume by contrast agent release from DPPG2-TSL. In conclusion, HT triggered drug delivery by using DPPG2-TSL is a promising tool in chemotherapy but effectiveness markedly depended on the method of heating and also on tumor size. Local HT using a cold light lamp or the new laser applicator allowed more efficient drug delivery than using a regional water bath heating. MR-compatibility of the new applicator gives the opportunity for future experiments investing drug delivery in more detail by MRI at low technical efforts. Copyright © 2015 Elsevier B.V. All rights reserved.

Aspergillus fumigatus Trehalose-Regulatory Subunit Homolog Moonlights To Mediate Cell Wall Homeostasis through Modulation of Chitin Synthase Activity.

PubMed

Thammahong, Arsa; Caffrey-Card, Alayna K; Dhingra, Sourabh; Obar, Joshua J; Cramer, Robert A

2017-04-25

Trehalose biosynthesis is found in fungi but not humans. Proteins involved in trehalose biosynthesis are essential for fungal pathogen virulence in humans and plants through multiple mechanisms. Loss of canonical trehalose biosynthesis genes in the human pathogen Aspergillus fumigatus significantly alters cell wall structure and integrity, though the mechanistic link between these virulence-associated pathways remains enigmatic. Here we characterize genes, called tslA and tslB , which encode proteins that contain domains similar to those corresponding to trehalose-6-phosphate phosphatase but lack critical catalytic residues for phosphatase activity. Loss of tslA reduces trehalose content in both conidia and mycelia, impairs cell wall integrity, and significantly alters cell wall structure. To gain mechanistic insights into the role that TslA plays in cell wall homeostasis, immunoprecipitation assays coupled with liquid chromatography-tandem mass spectrometry (LC-MS/MS) were used to reveal a direct interaction between TslA and CsmA, a type V chitin synthase enzyme. TslA regulates not only chitin synthase activity but also CsmA sub-cellular localization. Loss of TslA impacts the immunopathogenesis of murine invasive pulmonary aspergillosis through altering cytokine production and immune cell recruitment. In conclusion, our data provide a novel model whereby proteins in the trehalose pathway play a direct role in fungal cell wall homeostasis and consequently impact fungus-host interactions. IMPORTANCE Human fungal infections are increasing globally due to HIV infections and increased use of immunosuppressive therapies for many diseases. Therefore, new antifungal drugs with reduced side effects and increased efficacy are needed to improve treatment outcomes. Trehalose biosynthesis exists in pathogenic fungi and is absent in humans. Components of the trehalose biosynthesis pathway are important for the virulence of human-pathogenic fungi, including Aspergillus fumigatus Consequently, it has been proposed that components of this pathway are potential targets for antifungal drug development. However, how trehalose biosynthesis influences the fungus-host interaction remains enigmatic. One phenotype associated with fungal trehalose biosynthesis mutants that remains enigmatic is cell wall perturbation. Here we discovered a novel moonlighting role for a regulatory-like subunit of the trehalose biosynthesis pathway in A. fumigatus that regulates cell wall homeostasis through modulation of chitin synthase localization and activity. As the cell wall is a current and promising therapeutic target for fungal infections, understanding the role of trehalose biosynthesis in cell wall homeostasis and virulence is expected to help define new therapeutic opportunities. Copyright © 2017 Thammahong et al.

Derivation of Draft Ecological Soil Screening Levels for TNT and RDX Utilizing Terrestrial Plant and Soil Invertebrate Toxicity Benchmarks

DTIC Science & Technology

2012-11-01

TSL Soils Utilizing Growth Benchmarks for Alfalfa , Barnyard Grass, and Perennial Ryegrass ............................................. 5 3...Derivation of Terrestrial Plant-Based Draft Eco-SSL Value for RDX Weathered-and-Aged in SSL or TSL Soils Utilizing Growth Benchmarks for Alfalfa ...studies were conducted using the following plant species:  Dicotyledonous symbiotic species alfalfa (Medicago sativa L.)  Monocotyledonous

Reflections of Students in Their Use of Asynchronous Online Seminars

ERIC Educational Resources Information Center

Groves, Mark; O'Donoghue, John

2009-01-01

This paper reports on research that has been carried out into the use, process, and effectiveness of an asynchronous online seminar within an undergraduate sports studies degree programme. Contemporary sources are used to justify the use of technology supported learning (TSL) in higher education and to inform a reflective and critical account of…

Effects of conventional and no-tillage soil management and compost and sludge amendment on soil CO2 fluxes and microbial activities

NASA Astrophysics Data System (ADS)

Garcia-Gil, Juan Carlos; Haller, Isabel; Soler-Rovira, Pedro; Polo, Alfredo

2010-05-01

Soil management exerts a significant influence on the dynamic of soil organic matter, which is a key issue to enhance soil quality and its ecological functions, but also affects to greenhouse gas emissions and C sequestration processes. The objective of the present research was to determine the influence of soil management (conventional deep-tillage and no-tillage) and the application of two different organic amendment -thermally-dry sewage sludge (TSL) and municipal waste compost (MWC)- on soil CO2 fluxes and microbial activities in a long-term field experiment under semi-arid conditions. Both organic amendments were applied at a rate of 30 t ha-1 prior to sowing a barley crop. The experiment was conducted on an agricultural soil (Calcic Luvisol) from the experimental farm "La Higueruela" (Santa Olalla, Toledo). Unamended soils were used as control in both conventional and no-tillage management. During the course of the experiment, soil CO2 fluxes, microbial biomass C (MBC) and enzyme activities involved in the biogeochemical cycles of C, N and P were monitored during 12 months. The results obtained during the experiment for soil CO2 fluxes showed a great seasonal fluctuation due to semi-arid climate conditions. Overall, conventional deep-tillage soils exhibited higher CO2 fluxes, which was particularly larger during the first hours after deep-tillage was performed, and smaller MBC content and significantly lower dehydrogenase, beta-glucosidase, phosphatase, urease and BAA protease activities than no-tillage soils. Both MWC and TSL amendments provoked a significant increase of CO2 fluxes in both conventional and no-tillage soils, which was larger in TSL amended soils and particularly in no-tillage soils. The application of these organic amendments also enhanced MBC content and the overall enzyme activities in amended soils, which indicate a global revitalization of soil microbial metabolism in response to the fresh input of organic compounds that are energy sources for microbial growing, especially with TSL that is a raw organic material with no stabilization treatment.

Patterns of Control over the Teaching-Studying-Learning Process and Classrooms as Complex Dynamic Environments: A Theoretical Framework

ERIC Educational Resources Information Center

Harjunen, Elina

2012-01-01

In this theoretical paper the role of power in classroom interactions is examined in terms of a dominance continuum to advance a theoretical framework justifying the emergence of three ways of distributing power when it comes to dealing with the control over the teaching-studying-learning (TSL) "pattern of teacher domination," "pattern of…

DOE technical standards list: Department of Energy standards index

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This technical standards list (TSL) was prepared for use by personnel involved in the selection and use of US DOE technical standards and other government and non-government standards. This TSL provides listings of current DOE technical standards, non-government standards that have been adopted by DOE, other government documents in which DOE has a recorded interest, and cancelled DOE technical standards. Standards are indexed by type in the appendices to this document. Definitions of and general guidance for the use of standards are also provided.

Thermoluminescence as a Research Tool to Investigate Luminescence Mechanisms

PubMed Central

2017-01-01

Thermally stimulated luminescence (TSL) is known as a technique used in radiation dosimetry and dating. However, since the luminescence is very sensitive to the defects in a solid, it can also be used in material research. In this review, it is shown how TSL can be used as a research tool to investigate luminescent characteristics and underlying luminescent mechanisms. First, some basic characteristics and a theoretical background of the phenomenon are given. Next, methods and difficulties in extracting trapping parameters are addressed. Then, the instrumentation needed to measure the luminescence, both as a function of temperature and wavelength, is described. Finally, a series of very diverse examples is given to illustrate how TSL has been used in the determination of energy levels of defects, in the research of persistent luminescence phosphors, and in phenomena like band gap engineering, tunnelling, photosynthesis, and thermal quenching. It is concluded that in the field of luminescence spectroscopy, thermally stimulated luminescence has proven to be an experimental technique with unique properties to study defects in solids. PMID:29186873

Emission properties of Ce-doped alkaline earth borate glasses for scintillator applications

NASA Astrophysics Data System (ADS)

Torimoto, Aya; Masai, Hirokazu; Okada, Go; Kawaguchi, Noriaki; Yanagida, Takayuki

2017-11-01

We investigate the photoluminescence (PL) and X-ray-induced luminescence properties of 0.1 mol% Ce-doped MO-B2O3 (M = Ca, Sr, and Ba) glasses. We also determine the Ce3+/(Ce3++Ce4+) ratio by X-ray absorption near-edge structure analyses. The emission intensities of PL, X-ray scintillation, and thermally stimulated luminescence (TSL) depend on the host glass composition. The order of the PL intensity from highest to lowest is as follows: Ca-substituted glass, Ba-substituted glass, and Sr-substituted glass. Our results suggest that the optical absorption edge and quantum yield (QY) are influenced by the local coordination state of Ce3+, which, in turn, is likely to be affected by the optical basicity. The order of the X-ray scintillation intensity from highest to lowest is reverse of that of the PL intensity. This is probably because the interaction probability of X-rays with matter depends on the effective atomic number of the material and the effective atomic number has a stronger influence on the scintillation intensity than does the QY. Though the TSL glow curves reveal that the density and energy depth of the trap sites depend on the substituted alkaline earth oxides, we are unable to correlate the electron spin resonance (ESR) spectra with the TSL results. Therefore, it is considered that the ESR active sites are not responsible for the TSL in these systems.

Thermal biology, population fluctuations and implications of temperature extremes for the management of two globally significant insect pests.

PubMed

Nyamukondiwa, Casper; Weldon, Christopher W; Chown, Steven L; le Roux, Peter C; Terblanche, John S

2013-12-01

The link between environmental temperature, physiological processes and population fluctuations is a significant aspect of insect pest management. Here, we explore how thermal biology affects the population abundance of two globally significant pest fruit fly species, Ceratitis capitata (medfly) and C. rosa (Natal fruit fly), including irradiated individuals and those expressing a temperature sensitive lethal (tsl) mutation that are used in the sterile insect technique. Results show that upper and lower lethal temperatures are seldom encountered at the field sites, while critical minimum temperatures for activity and lower developmental thresholds are crossed more frequently. Estimates of abundance revealed that C. capitata are active year-round, but abundance declines markedly during winter. Temporal autocorrelation of average fortnightly trap captures and of development time, estimated from an integrated model to calculate available degree days, show similar seasonal lags suggesting that population increases in early spring occur after sufficient degree-days have accumulated. By contrast, population collapses coincide tightly with increasing frequency of low temperature events that fall below critical minimum temperatures for activity. Individuals of C. capitata expressing the tsl mutation show greater critical thermal maxima and greater longevity under field conditions than reference individuals. Taken together, this evidence suggests that low temperatures limit populations in the Western Cape, South Africa and likely do so elsewhere. Increasing temperature extremes and warming climates generally may extend the season over which these species are active, and could increase abundance. The sterile insect technique may prove profitable as climates change given that laboratory-reared tsl flies have an advantage under warmer conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Marker-Dependent Recombination in T4 Bacteriophage. IV. Recombinational Effects of Antimutator T4 DNA Polymerase

PubMed Central

Shcherbakov, V. P.; Plugina, L. A.; Kudryashova, E. A.

1995-01-01

Recombinational effects of the antimutator allele tsL42 of gene 43 of phage T4, encoding DNA polymerase, were studied in crosses between rIIB mutants. Recombination under tsL42-restricted conditions differed from the normal one in several respects: (1) basic recombination was enhanced, especially within very short distances; (2) mismatch repair tracts were shortened, while the contribution of mismatch repair to recombination was not changed; (3) marker interference at very short distances was augmented. We infer that the T4 DNA polymerase is directly involved in mismatch repair, performing both excision of a nonmatched single strand (by its 3' -> 5' exonuclease) and filling the resulting gap. A pathway for the mismatch repair was substantiated; it includes sequential action of endo VII (gp49) -> 3'->5' exonuclease (gp43) -> DNA polymerase (gp43) -> DNA ligase (gp30). It is argued that the marker interference at very short distances may result from the same sequence of events during the final processing of recombinational intermediates. PMID:7635281

Experimental co-digestion of corn stalk and vermicompost to improve biogas production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen Guangyin; Zheng Zheng, E-mail: zzhenghj@fudan.edu.c; Department of Environmental Science and Engineering, Fudan University, Shanghai 200433

2010-10-15

Anaerobic co-digestion of corn stalk and vermicompost (VC) as well as mono-digestion of corn stalk were investigated. Batch mono-digestion experiments were performed at 35 {+-} 1 {sup o}C and initial total solid loading (TSL) ranged from 1.2% to 6.0%. Batch co-digestion experiments were performed at 35 {+-} 1 {sup o}C and initial TSL of 6% with VC proportions ranged from 20% to 80% of total solid (TS). For mono-digestion of corn stalk, a maximum methane yield of 217.60 {+-} 13.87 mL/g TS{sub added} was obtained at initial TSL of 4.8%, and acidification was found at initial TSL of 6.0% withmore » the lowest pH value of 5.10 on day 4. Co-digestion improved the methane yields by 4.42-58.61% via enhancing volatile fatty acids (VFAs) concentration and pH value compared with mono-digestion of corn stalk. The maximum biogas yield of 410.30 {+-} 11.01 mL/g TS{sub added} and methane yield of 259.35 {+-} 13.85 mL/g TS{sub added} were obtained for 40% VC addition. Structure analysis by X-ray diffractometry (XRD) showed that the lowest crystallinity of 35.04 of digested corn stalk was obtained from co-digestion with 40% VC, which decreased 29.4% compared to 49.6 obtained from un-treated corn stalk. It is concluded that co-digestion with VC is beneficial for improving biodigestibility and methane yield from corn stalk.« less

Optically- and thermally-stimulated luminescences of Ce-doped SiO2 glasses prepared by spark plasma sintering

NASA Astrophysics Data System (ADS)

Okada, Go; Kasap, Safa; Yanagida, Takayuki

2016-11-01

Rare-earth doped phosphors have been used in many applications including radiation measurements. In the latter applications, the radiation photons are converted to light so that we can indirectly detect the radiation using a conventional photodetector. In this work, we have prepared and characterized a Ce-doped SiO2 glass for dosimeter applications. Unlike conventional techniques such as sol-gel synthesis, the sample was prepared by spark plasma sintering. Although the PL emission seems to be only from the Ce3+ ions in the structure, due to the X-ray induced luminescence, we have also observed optically-stimulated luminescence (OSL), and thermally-stimulated luminescence (TSL), owing to a pair of silylenes and a set of dioxasilirane and silylene in addition to Ce3+. We have measured the detector response vs irradiation dose for both the OSL and TSL. The detector response in both cases is linear over the dose range from at least 1 mGy to 2 Gy. Particularly, the sensitivity of TSL is so high that it should be considered to be a good candidate for practical applications.

Photoacoustic Imaging of Cancer Treatment Response: Early Detection of Therapeutic Effect from Thermosensitive Liposomes

PubMed Central

Wirtzfeld, Lauren A.; Undzys, Elijus; Li, Shyh-Dar; Kolios, Michael C.

2016-01-01

Imaging methods capable of indicating the potential for success of an individualized treatment course, during or immediately following the treatment, could improve therapeutic outcomes. Temperature Sensitive Liposomes (TSLs) provide an effective way to deliver chemotherapeutics to a localized tumoral area heated to mild-hyperthermia (HT). The high drug levels reached in the tumor vasculature lead to increased tumor regression via the cascade of events during and immediately following treatment. For a TSL carrying doxorubicin (DOX) these include the rapid and intense exposure of endothelial cells to high drug concentrations, hemorrhage, blood coagulation and vascular shutdown. In this study, ultrasound-guided photoacoustic imaging was used to probe the changes to tumors following treatment with the TSL, HaT-DOX (Heat activated cytoToxic). Levels of oxygen saturation (sO2) were studied in a longitudinal manner, from 30 min pre-treatment to 7 days post-treatment. The efficacious treatments of HT-HaT-DOX were shown to induce a significant drop in sO2 (>10%) as early as 30 min post-treatment that led to tumor regression (in 90% of cases); HT-Saline and non-efficacious HT-HaT-DOX (10% of cases) treatments did not show any significant change in sO2 at these timepoints. The changes in sO2 were further corroborated with histological data, using the vascular and perfusion markers CD31 and FITC-lectin. These results allowed us to further surmise a plausible mechanism of the cellular events taking place in the TSL treated tumor regions over the first 24 hours post-treatment. The potential for using photoacoustic imaging to measure tumor sO2 as a surrogate prognostic marker for predicting therapeutic outcome with a TSL treatment is demonstrated. PMID:27788199

Optical, scintillation and dosimeter properties of MgO:Tb translucent ceramics synthesized by the SPS method

NASA Astrophysics Data System (ADS)

Kawano, Naoki; Kato, Takumi; Okada, Go; Kawaguchi, Noriaki; Yanagida, Takayuki

2017-11-01

MgO translucent ceramics doped with different concentrations of Tb (0.01, 0.05, 0.1, 0.5%) were prepared by the Spark Plasma Sintering (SPS) method. Further, the optical, scintillation, dosimeter properties of were evaluated systematically. In the photoluminescence (PL) and scintillation spectra, sharp emission peaks due to the 4f-4f transitions of Tb3+ were observed. In the PL and scintillation decay curves, the decay time constants were a few ms which were on a typical order of the 4f-4f transitions of Tb3+. The thermally-stimulated luminescence (TSL) glow curves exhibited glow peaks around 80, 160 °C after X ray irradiation of 10 mGy. The intensity of TSL peak at 160 °C exhibited a linear response against X-ray dose over a dose range of 0.1-10 mGy. The optically-stimulated luminescence (OSL) under 590 nm stimulation exhibited strong emissions due to Tb3+ around 385-550 nm after X-ray irradiation. As in TSL, the intensity of OSL peak showed a linear response to X-ray dose, and the dynamic range confirmed was 0.1-1000 mGy.

Scintillation properties of rare-earth doped NaPO3-Al(PO3)3 glasses

NASA Astrophysics Data System (ADS)

Kuro, Tomoaki; Okada, Go; Kawaguchi, Noriaki; Fujimoto, Yutaka; Masai, Hirokazu; Yanagida, Takayuki

2016-12-01

We systematically investigated photoluminescence (PL), scintillation and dosimeter properties of rare-earth (RE) doped NaPO3-Al(PO3)3 (NAP) glasses. The NAP glasses doped with a series of RE ions (La-Yb, except Pm) with a consistent concentration (0.3 wt%) were prepared by the conventional melt-quenching method. The PL and scintillation decay time profiles showed fast (ns) and slow (μs or ms) components: the fast components from 15 to 100 ns were due to the host or 5d-4f transition emission, and the slow components from 15 μs to 5 ms were due to the 4f-4f transitions of RE. The thermally stimulated luminescence (TSL) was evaluated as a dosimeter property, and glow peaks appeared around 400 °C in all the samples. The TSL dose response function was examined in the dose range from 10 mGy to 10 Gy. Among the samples tested, Nd and Tb doped glasses showed higher signal by at least one order of magnitude than those of non-doped and other RE-doped samples. Over the dose range tested, the TSL signals are linearly related with the incident X-ray dose, showing a potential for practical applications.

Fluoride Varnishes against Dental Erosion Caused by Soft Drink Combined with Pediatric Liquid Medicine.

PubMed

Alexandria, Adílis Kalina; Valença, Ana Maria Gondim; Cabral, Lúcio Mendes; Maia, Lucianne Cople

2017-01-01

The present study evaluated the effect of NaF and CPP-ACP/NaF varnishes to reduce erosion produced by soft drink (SD) combined or not with pediatric liquid medicine. Enamel specimens were pre-treated with fluoride varnish, according to the following groups: NaF varnish (Duraphat®) or CPP-ACP/NaF varnish (MI varnishTM). Two types of erosive cycles were made: by soft drink erosion (SDE) or by pediatric liquid medicine plus soft drink erosion (PLM/SDE). Bovine enamel specimens were randomly assigned in six groups (n=10): G1=NaF + SDE; G2=CPP-ACP/NaF + SDE; G3=Distilled and deionized (DD) water + SDE; G4=NaF + PLM/SDE; G5=CPP-ACP/NaF + PLM/SDE and G6=DD water + PLM/SDE. Before treatments, the sample surface was divided in two areas (unexposed area-UA and exposed area-EA). The specimens were evaluated by 3D non-contact profilometry technique to determinate tooth structure loss (TSL) and surface roughness (Sa). Scanning electron microscopy (SEM) analysis was also performed. After SDE, G2 presented the lowest TSL values compared to G3 (p=0.008). G1 and G2 did not differ between them (p=0.203) and no groups differed among them despite Sa. Regarding TSL and Sa, G4 and G5 differed from G6 (p=0.0001), but not between them (p=1.00). Examining 3D and SEM images, the greatest differences between UA and EA were observed for G3 and G6. CPP-ACP/NaF varnish seems to be a promising treatment to reduce enamel loss from the erosion produced by a soft drink. Both varnishes also showed capacity to reduce TSL and Sa after erosion by soft drink combined to pediatric liquid medicine.

Scintillation and storage luminescence properties of MgF2 transparent ceramics doped with Ce3+

NASA Astrophysics Data System (ADS)

Nakamura, Fumiya; Kato, Takumi; Okada, Go; Kawaguchi, Noriaki; Fukuda, Kentaro; Yanagida, Takayuki

2017-10-01

In this paper, we report basic optical properties and scintillation and storage luminescence properties of MgF2:Ce transparent ceramics with different doping concentrations of Ce (0.01, 0.1 and 1%) synthesized by spark plasma sintering (SPS). In scintillation, thermally-stimulated luminescence (TSL) and optically-stimulated luminescence (OSL), the dominant emissions were due to the 5d-4f transitions of Ce3+ which appeared in the near-UV region peaking around 320 and 360 nm. The scintillation was evaluated by X-ray irradiation while OSL was observed under 540 nm stimulation. In particular, the TSL sensitivity was high and showed a good linearity from 0.1 mGy to 1000 mGy.

Design of a portable fluoroquinolone analyzer based on terbium-sensitized luminescence

NASA Astrophysics Data System (ADS)

Chen, Guoying

2007-09-01

A portable fluoroquinolone (FQ) analyzer is designed and prototyped based on terbium-sensitized luminescence (TSL). The excitation source is a 327-nm light emitting diode (LED) operated in pulsed mode; and the luminescence signal is detected by a photomultiplier tube (PMT). In comparison to a conventional xenon flashlamp, an LED is small, light, robust, and energy efficient. More importantly, its narrow emission bandwidth and low residual radiation reduce background signal. In pulse mode, an LED operates at a current 1-2 orders of magnitude lower than that of a xenon flashlamp, thus minimizing electromagnetic interference (EMI) to the detector circuitry. The PMT is gated to minimize its response to the light source. These measures lead to reduced background noise in time domain. To overcome pulse-to-pulse variation signal normalization is implemented based on individual pulse energy. Instrument operation and data processing are controlled by a computer running a custom LabVIEW program. Enrofloxacin (ENRO) is used as a model analyte to evaluate instrument performance. The integrated TSL intensity reveals a linear dependence up to 2 ppm. A 1.1-ppb limit of detection (LOD) is achieved with relative standard deviation (RSD) averaged at 5.1%. The background noise corresponds to ~5 ppb. At 19 lbs, this portable analyzer is field deployable for agriculture, environmental and clinical analyses.

The application of the piecewise linear approximation to the spectral neighborhood of soil line for the analysis of the quality of normalization of remote sensing materials

NASA Astrophysics Data System (ADS)

Kulyanitsa, A. L.; Rukhovich, A. D.; Rukhovich, D. D.; Koroleva, P. V.; Rukhovich, D. I.; Simakova, M. S.

2017-04-01

The concept of soil line can be to describe the temporal distribution of spectral characteristics of the bare soil surface. In this case, the soil line can be referred to as the multi-temporal soil line, or simply temporal soil line (TSL). In order to create TSL for 8000 regular lattice points for the territory of three regions of Tula oblast, we used 34 Landsat images obtained in the period from 1985 to 2014 after their certain transformation. As Landsat images are the matrices of the values of spectral brightness, this transformation is the normalization of matrices. There are several methods of normalization that move, rotate, and scale the spectral plane. In our study, we applied the method of piecewise linear approximation to the spectral neighborhood of soil line in order to assess the quality of normalization mathematically. This approach allowed us to range normalization methods according to their quality as follows: classic normalization > successive application of the turn and shift > successive application of the atmospheric correction and shift > atmospheric correction > shift > turn > raw data. The normalized data allowed us to create the maps of the distribution of a and b coefficients of the TSL. The map of b coefficient is characterized by the high correlation with the ground-truth data obtained from 1899 soil pits described during the soil surveys performed by the local institute for land management (GIPROZEM).

Effect of dried sunflower seeds on incisal edge abrasion: A rare case report.

PubMed

Rath, Avita; Ramamurthy, Priyadarshini H; Fernandes, Bennete Aloysius; Sidhu, Preena

2017-01-01

Tooth surface loss (TSL) is a complex phenomenon characterized by the loss of hard tooth structure at various locations of the teeth, usually due to more than one factor. TSL due to abrasion can be significant in patients consuming coarse, abrasive diet. The present case reports an interesting incisal edge abrasion in a female patient, attributed to a particular dietary behavior of long-term consumption of sunflower seeds. All her family members and most of the people from her native place were also reported to have similar lesions by the patient. Larger epidemiological studies to assess the prevalence and severity of such abrasive lesions in geographic areas with this particular dietary habit need to be carried out so that people may be made aware and educated about alternative ways of eating sunflower seeds that will not cause any form of tooth wear.

Application of TSL Underwater Robots (AUV) for Investigation of Benthic Ecosystems and Quantification of Benthic Invertebrate Reserves

NASA Astrophysics Data System (ADS)

Golikov, S. Yu; Dulepov, V. I.; Maiorov, I. S.

2017-11-01

The issues on the application of autonomous underwater vehicles for assessing the abundance, biomass, distribution and reserves of invertebrates in the marine benthic ecosystems and on the environmental monitoring are discussed. An example of the application of methodology to assess some of the quantitative characteristics of macrobenthos is provided based upon using the information obtained from the TSL AUV in the Peter the Great Gulf (the Sea of Japan) in the Bay of Paris and the Eastern Bosphorus Strait within the area of the bridge leading to the Russian island. For the quantitative determination of the benthic invertebrate reserves, the values of biomass density of specific species are determined. Based on the data of direct measurements and weightings, the equations of weight dependencies on the size of animals are estimated according to the studied species that are well described by the power law dependence.

[How the patients on sick leave assess the Medical Inspector: The Institut Català d'Avaluacions Mèdiques (ICAM) experience in Catalonia].

PubMed

Gálvez Hernando, G; Mira Solves, J J; Jardí Lliberia, J; Guilabert Mora, M; Manzanera López, R

2012-01-01

To analyse the patient perception of the medical inspector, and to examine whether this perception is related with the outcome of the medical report. A cross-sectional study based on telephone interviews with a random sample of patients visited in Catalonia in 2010 for temporary (TSL) or permanent (PSL) sick leave. The study was conducted in November 2011. A stratified sample considering the time from the consultation and province where patients were visited was used. The scale was assessed by Intraclass Correlation coefficient (0.93, 95% CI; 0.92-0.94) and testing with the Spearman-Brown split-half coefficient (0.93). A total of 609 patients were surveyed. A majority of them (400; 65.7%) had a positive opinion of the medical inspector. When PSL was denied, the assessment was worse (P=.002), this was different when TSL was cancelled. Patients who did not continue in PSL stated that doctor's decisions were determined by non-medical interests, and not oriented to the defence of the patient's rights (odds ratio 2.8, 95% CI; 1.7 to 4.8). When the perceptions were negative, patients focus their criticism on the role of medical inspector (P<.001), and not about the organisational aspects. When inspectors cancel PSL, patient's perception is strongly associated with a negative assessment of their performance, capacity and independence of the physician. This is not so in the case of TSL. Copyright © 2011 SECA. Published by Elsevier Espana. All rights reserved.

Radiation-induced luminescence properties of Tb-doped Li3PO4-B2O3 glasses

NASA Astrophysics Data System (ADS)

Isokawa, Yuya; Hirano, Shotaro; Kawano, Naoki; Okada, Go; Kawaguchi, Noriaki; Yanagida, Takayuki

2018-02-01

In this study, we developed Li3PO4-B2O3 glasses doped with different concentrations of Tb (0.1, 0.3, 1.0, 3.0, and 10.0%) as well as undoped glass, and then the prepared glasses were studied for the optical, dosimeter and scintillator properties. The Tb-doped samples indicated radioluminescence and photoluminescence (PL) due to the 4f-4f transitions of Tb3+ with sharp spectral features peaking around 375, 410, 435, 480, 540, 590 and 620 nm. The luminescence decay times of radioluminescence and PL were 2.3-2.7 ms and 2.7-2.9 ms, respectively. The shorter radioluminescence decay time than that of PL indicated quenching effect of excited states in radioluminescence. As the concentration of Tb increased, both the radioluminescence intensity and PL quantum yield (QY) increased, and the 10.0% Tb-doped sample showed the highest radioluminescence intensity and QY (54.3%). In addition, thermally-stimulated luminescence (TSL) was observed after irradiating with X-rays. The sensitivity was the highest for the 3.0% Tb-doped sample having a dynamic range from 0.1 mGy to 10 Gy, which was equivalent to commercial dosimeters. The comprehensive studies suggested that X-ray generated charges are captured at TSL-active centers more effectively at lower concentrations of Tb whereas the recombination probability at Tb center during irradiation increases with the concentration of Tb. Consequently, the optimal Tb concentration was 10% as scintillator and 3.0% for TSL dosimeter, among the present samples.

SrAl2O4:Eu2+ (1%) luminescence under UV, VUV and electron beam excitation

NASA Astrophysics Data System (ADS)

Nazarov, M.; Mammadova, S.; Spassky, D.; Vielhauer, S.; Abdullayeva, S.; Huseynov, A.; Jabbarov, R.

2018-01-01

This paper reports the luminescence properties of nanosized SrAl2O4:Eu2+ (1%) phosphors. The samples were prepared by combustion method at 600 °C, followed by annealing of the resultant combustion ash at 1000 °C in a reductive (Ar + H2) atmosphere. X-ray diffraction (XRD), photo luminescence (PL) and cathodoluminescence (CL) analysis and thermal stimulated luminescence (TSL) method were applied to characterize the phosphor. For the first time a peak at 375 nm was observed in CL spectra of SrAl2O4:Eu2+ (1%) nanophosphors. Luminescence excitation spectra analysis have shown that this peak is related to crystal defects. Also in TSL curve one strong peak was observed in the region above room temperature (T = 325 K), which is attributed to lattice defects, namely oxygen vacancies. A green LED was fabricated by the combination of the SrAl2O4:Eu2+ (1%) nanosized phosphor and a 365 nm UV InGaN chip.

Production Suitability of an Electroform Conductive Wax Process for the Manufacture of Fluidic Systems

DTIC Science & Technology

1975-11-01

2l«^,«’) T>SL JI To «ATt JlOO «n «t* in. fTA * 3^ "PlbiA-e-*^ To wia •^ -IZ0"L6, (.21 >To «AUVK« ^-^STRlP^TiM e.ax>s «»I To RATft...8 C B E U^T^SJA ani« fMD ran © HMajrwelL "« TEftT COkTTRoL ’PAMB.V, ■•i’r^rT" I’» 1 Mj u 56- £ to i. — TOO*.« r7gi^iiiiniM.gi 4|ji»" mkd

Affordable Online Maths Tuition: Evaluation Report and Executive Summary

ERIC Educational Resources Information Center

Torgerson, Carole; Ainsworth, Hannah; Buckley, Hannah; Hampden-Thompson, Gillen; Hewitt, Catherine; Humphry, Deborah; Jefferson, Laura; Mitchell, Natasha; Torgerson, David

2016-01-01

"Affordable Online Maths Tuition" is a one-to-one tutoring programme where pupils receive maths tuition over the internet from trained maths graduates in India and Sri Lanka. It is delivered by the organisation Third Space Learning (TSL). Tutors and pupils communicate using video calling and a secure virtual classroom. Before each…

Biotransformation of arsenite and bacterial aox activity in drinking water produced from surface water of floating houses: Arsenic contamination in Cambodia.

PubMed

Chang, Jin-Soo

2015-11-01

The potential arsenite bioteansformation activity of arsenic was investigated by examining bacterial arsenic arsenite-oxidizing gene such as aoxS, aoxR, aoxA, aoxB, aoxC, and aoxD in high arsenic-contaminated drinking water produced from the surface water of floating houses. There is a biogeochemical cycle of activity involving arsenite oxidase aox system and the ars (arsenic resistance system) gene operon and aoxR leader gene activity in Alcaligenes faecalis SRR-11 and aoxS leader gene activity in Achromobacter xylosoxidans TSL-66. Batch experiments showed that SRR-11 and TSL-66 completely oxidized 1 mM of As (III) to As (V) within 35-40 h. The leaders of aoxS and aoxR are important for gene activity, and their effects in arsenic bioremediation and mobility in natural water has a significant ecological role because it allows arsenite oxidase in bacteria to control the biogeochemical cycle of arsenic-contaminated drinking water produced from surface water of floating houses. Copyright © 2015 Elsevier Ltd. All rights reserved.

Speaking Conflict: Ideological Barriers to Bilingual Policy Implementation in Civil War Sri Lanka

ERIC Educational Resources Information Center

Davis, Christina P.

2015-01-01

This article presents a holistic view of ideological barriers to bilingual policy implementation in Sri Lanka, a conflict-ridden postcolonial nation-state. I examine Sinhalese youth and adults' Tamil as a second language (TSL) learning and speaking practices across three contexts: a multilingual school, a program for government servants, and an…

Evaluation of the TSL® Program for Parents of Children with Cancer

ERIC Educational Resources Information Center

Choi, Kwonho; Kim, Jae Yop

2018-01-01

Objectives: This study aims to investigate the effects of the "Thank you-Sorry-Love" (TSL®) program on posttraumatic growth (PTG) and cortisol level in parents of children with cancer. Methods: A total of 15 mothers of children with cancer were randomly assigned to the experimental group (n = 7) with the TSL intervention or a control…

75 FR 47041 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-04

... Exploration CI CIGNA Corp. & Production Co. GPS Gap Inc/The........ ESI ITT Educational Services Inc. TSL... CB Chubb Corp. ATPG ATP Oil & Gas Corp/ ADM Archer-Daniels- United States. Midland Co. YUM Yum! Brands Inc.... HSY Hershey Co/The. RCL Royal Caribbean TXT Textron Inc. Cruises Ltd. BPOP Popular Inc...

75 FR 47043 - Self-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-04

... Educational Services Inc 280 TSL Trina Solar Ltd 332 NKE NIKE Inc 282 EWW iShares MSCI Mexico 335 FIS Fidelity...-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing and Immediate Effectiveness of a Proposed...\\ notice is hereby given that on July 26, 2010, BATS Exchange, Inc. (the ``Exchange'' or ``BATS'') filed...

75 FR 47664 - Self-Regulatory Organizations; NASDAQ OMX PHLX, Inc.; Notice of Filing and Immediate...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-06

..../The 331 ESI ITT Educational Services Inc. 280 TSL Trina Solar Ltd. 332 NKE NIKE Inc. 282 EWW iShares...-Regulatory Organizations; NASDAQ OMX PHLX, Inc.; Notice of Filing and Immediate Effectiveness of Proposed..., notice is hereby given that on July 22, 2010, NASDAQ OMX PHLX, Inc. (``Phlx'' or ``Exchange'') filed with...

75 FR 48385 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-10

... Gap Inc/The 331 ESI ITT Educational Services Inc. 280 TSL Trina Solar Ltd......... 332 NKE NIKE Inc...-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of Proposed Rule... hereby given that on July 20, 2010, NYSE Arca, Inc. (``NYSE Arca'' or the ``Exchange'') filed with the...

77 FR 31964 - Energy Conservation Program: Energy Conservation Standards for Residential Dishwashers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-30

... year used for discounting the NPV of total consumer costs and savings, for the time-series of costs and... does not imply that the time-series of cost and benefits from which the annualized values were... each TSL, DOE has included tables that present a summary of the results of DOE's quantitative analysis...

Electrical Conductivity Measurements of Hydroxylammonium Nitrate: Design Considerations

DTIC Science & Technology

1986-04-01

aqueous NaNO3 i• shown as well to indicate the similarity of this conductivity data with that cf HAN. The solubility of NaNO 3 in H120 is much less than... Wilmot , R-16 Commander Silver Spring, MD 20910 US Army Tank Automotive Command 1 Commander ATTN: AMSTA-TSL Naval Weapons Center Warren, MI 48397-5000

Proteomic identification of a potential sex biomarker for 2 fruit fly species at pupal stage

USDA-ARS?s Scientific Manuscript database

We collected brown and white pupae from rearing DTWP larvae on liquid diet and TSL strain from CDFA rearing facility respectively and daily and analyzed protein expression from pupal age 1-10 days old using 2D electrophoresis. In this report, two pupal color sexing strain [dorsalis translocation whi...

75 FR 47875 - Self-Regulatory Organizations; NASDAQ OMX BX, Inc.; Notice of Filing and Immediate Effectiveness...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-09

... the Securities and Exchange Commission (``Commission'') to, among other things, expand the number of... Oilwell Varco Inc. TSL Trina Solar Ltd. TWX Time Warner Inc. EWW iShares MSCI Mexico XOP SPDR S&P Oil... Commission's Internet comment form ( http://www.sec.gov/rules/sro.shtml ); or Send an e-mail to rule-comments...

Seasonal variation of acute toxoplasmic lymphadenopathy in the United States.

PubMed

Contopoulos-Ioannidis, D; Talucod, J; Maldonado, Y; Montoya, J G

2015-07-01

We describe the seasonal variation of acute toxoplasmosis in the United States. Acute toxoplasmic lymphadenopathy (ATL) can be a surrogate of acute toxoplasmosis in patients in whom the date of onset of lymphadenopathy matches the window of acute infection predicted by serological tests performed at a reference laboratory. We used the electronic database of the Palo Alto Medical Foundation Toxoplasma Serology Laboratory (PAMF-TSL) (1997-2011) to identify cases of ATL. We tested the uniformity of distribution of ATL cases per month, across the 12 calendar months, using circular statistics uniformity tests. We identified 112 consecutive cases of ATL. The distribution of cases was not uniform across the 12 calendar months. We observed the highest peak of cases in December and a second highest peak in September. Similar months were identified in patients with acute toxoplasmosis in rural areas in France. The results were similar when we performed weighted analyses, weighting for the total number of Toxoplasma gondii IgG tests performed per month in the PAMF-TSL laboratory. This is the largest study to date of the seasonal variation of ATL in the United States. Physicians should advise high-risk individuals to avoid risk factors associated with T. gondii infections especially around those months.

75 FR 47054 - Self-Regulatory Organizations; International Securities Exchange, LLC; Notice of Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-04

... Inc 280 TSL Trina Solar Ltd 332 NKE NIKE Inc 282 EWW iShares MSCI Mexico 335 FIS Fidelity National... 199 MBI MBIA Inc 316 CB Chubb Corp 205 MA Mastercard Inc 320 ADM Archer-Daniels-Midland Co 224 ATPG ATP Oil & Gas Corp/United 322 HSY Hershey Co/The States. 226 YUM Yum! Brands Inc 323 TXT Textron Inc...

Net discharge anomalies drive uncertainty in catch in the world's largest inland fishery

NASA Astrophysics Data System (ADS)

Sabo, J. L.

2013-12-01

The Mekong River is one of the world's largest rivers at more than 4,600 km long and a watershed of nearly 800,000 km2. The Tonle Sap Lake (TSL) in Cambodia is believed to be one of the most productive inland fisheries in the world because of its unique hydrologic regime and large input of nutrient-rich sediment from the Mekong. The TSL is the cornerstone of food security in Cambodia yielding ~ 15% of the estimated 2.6M tonne catch in the Mekong basin and providing key nursery habitat for fishes that constitute the catch in other parts of the basin. The TSL fishery is driven by a flood pulse that occurs during and after the SE Asian Monsoon. The timing, duration and magnitude of the monsoon is thought to be a key driver of primary and secondary (fish) production in the system. All three-timing, duration and magnitude--are likely to be different under future climate and as a result of the proposed and recently constructed dams on tributaries in Vietnam and elsewhere. Here I use spectral methods to characterize the timing and magnitude of the flood pulse. Specifically, I use the Discrete Fast Fourier Transform (DFFT) to estimate the seasonal trend in daily discharge for the past 40 years at the Stung Treng gage. The whitened time series represent departures from the long term trend--anomalies--and hence implicitly capture the timing of unusual events. I hypothesize that 'timing is everything' and hence that anomalies will capture variation in the second moment of the fishery. Using a novel metric--the net annual discharge anomaly--I show that catch is significantly more variable in years with net negative flow anomalies; and quite predictable in years with net positive flow anomalies. These results suggest that changes in timing of monsoon flows alone--due to climate change or dams--can significantly increase the uncertainty in catch of a fishery that is vital for food security in the Mekong basin.

Anti-pandemic influenza A (H1N1) virus potential of catechin and gallic acid.

PubMed

You, Huey-Ling; Huang, Chao-Chun; Chen, Chung-Jen; Chang, Cheng-Chin; Liao, Pei-Lin; Huang, Sheng-Teng

2018-05-01

The pandemic influenza A (H1N1) virus has spread worldwide and infected a large proportion of the human population. Discovery of new and effective drugs for the treatment of influenza is a crucial issue for the global medical community. According to our previous study, TSL-1, a fraction of the aqueous extract from the tender leaf of Toonasinensis, has demonstrated antiviral activities against pandemic influenza A (H1N1) through the down-regulation of adhesion molecules and chemokine to prevent viral attachment. The aim of the present study was to identify the active compounds in TSL-1 which exert anti-influenza A (H1N1) virus effects. XTT assay was used to detect the cell viability. Meanwhile, the inhibitory effect on the pandemic influenza A (H1N1) virus was analyzed by observing plaque formation, qRT-PCR, neuraminidase activity, and immunofluorescence staining of influenza A-specific glycoprotein. Both catechin and gallic acid were found to be potent inhibitors in terms of influenza virus mRNA replication and MDCK plaque formation. Additionally, both compounds inhibited neuraminidase activities and viral glycoprotein. The 50% effective inhibition concentration (EC 50 ) of catechin and gallic acid for the influenza A (H1N1) virus were 18.4 μg/mL and 2.6 μg/mL, respectively; whereas the 50% cytotoxic concentrations (CC 50 ) of catechin and gallic acid were >100 μg/mL and 22.1 μg/mL, respectively. Thus, the selectivity indexes (SI) of catechin and gallic acid were >5.6 and 22.1, respectively. The present study demonstrates that catechin might be a safe reagent for long-term use to prevent influenza A (H1N1) virus infection; whereas gallic acid might be a sensitive reagent to inhibit influenza virus infection. We conclude that these two phyto-chemicals in TSL-1 are responsible for exerting anti-pandemic influenza A (H1N1) virus effects. Copyright © 2017. Published by Elsevier Taiwan LLC.

CHELSI: a portable neutron spectrometer for the 20-800 MeV region.

PubMed

McLean, T D; Olsher, R H; Romero, L L; Miles, L H; Devine, R T; Fallu-Labruyere, A; Grudberg, P

2007-01-01

CHELSI is a CsI-based portable spectrometer being developed at Los Alamos National Laboratory for use in high-energy neutron fields. Based on the inherent pulse shape discrimination properties of CsI(Tl), the instrument flags charged particle events produced via neutron-induced spallation events. Scintillation events are processed in real time using digital signal processing and a conservative estimate of neutron dose rate is made based on the charged particle energy distribution. A more accurate dose estimate can be made by unfolding the 2D charged particle versus pulse height distribution to reveal the incident neutron spectrum from which dose is readily obtained. A prototype probe has been assembled and data collected in quasi-monoenergetic fields at The Svedberg Laboratory (TSL) in Uppsala as well as at the Los Alamos Neutron Science Center (LANSCE). Preliminary efforts at deconvoluting the shape/energy data using empirical response functions derived from time-of-flight measurements are described.

Ion Acoustic Microscopy

DTIC Science & Technology

1985-07-01

Walter Bryzik I AMSTA-RGET, Mr. John Lewakowski I AMSTA-TMM, Ms. Jan Dentel 1 AMSTA-TBM, Mr. William Moncrief 1 AMSTA-TSL 2 Director, U.S. Army Materials...DOCUMENTATION PAGE ,a. REPORr SECUPR:lY C .’ASSIFICATION lb. RESTRICTIVE MARKINGS UNCLASSIFIED NONE 2a. SECURITY CiA55,iICATION AUTHORITY 3 . DIST IRIUTION...Implanted Region. b) Periphery Of Implanted Spot . . . . . . . . .......... 15 c ) Further Inside Implanted Region. d) Further Inside Implanted Region

Sensory Alterations in Patients with Isolated Idiopathic Dystonia: An Exploratory Quantitative Sensory Testing Analysis.

PubMed

Paracka, Lejla; Wegner, Florian; Blahak, Christian; Abdallat, Mahmoud; Saryyeva, Assel; Dressler, Dirk; Karst, Matthias; Krauss, Joachim K

2017-01-01

Abnormalities in the somatosensory system are increasingly being recognized in patients with dystonia. The aim of this study was to investigate whether sensory abnormalities are confined to the dystonic body segments or whether there is a wider involvement in patients with idiopathic dystonia. For this purpose, we recruited 20 patients, 8 had generalized, 5 had segmental dystonia with upper extremity involvement, and 7 had cervical dystonia. In total, there were 13 patients with upper extremity involvement. We used Quantitative Sensory Testing (QST) at the back of the hand in all patients and at the shoulder in patients with cervical dystonia. The main finding on the hand QST was impaired cold detection threshold (CDT), dynamic mechanical allodynia (DMA), and thermal sensory limen (TSL). The alterations were present on both hands, but more pronounced on the side more affected with dystonia. Patients with cervical dystonia showed a reduced CDT and hot detection threshold (HDT), enhanced TSL and DMA at the back of the hand, whereas the shoulder QST only revealed increased cold pain threshold and DMA. In summary, QST clearly shows distinct sensory abnormalities in patients with idiopathic dystonia, which may also manifest in body regions without evident dystonia. Further studies with larger groups of dystonia patients are needed to prove the consistency of these findings.

Spatio-temporal variation of fish taxonomic composition in a South-East Asian flood-pulse system.

PubMed

Kong, Heng; Chevalier, Mathieu; Laffaille, Pascal; Lek, Sovan

2017-01-01

The Tonle Sap Lake (TSL) is a flood-pulse system. It is the largest natural lake in South-East Asia and constitutes one of the largest fisheries over the world, supporting the livelihood of million peoples. Nonetheless, the Mekong River Basin is changing rapidly due to accelerating water infrastructure development (hydropower, irrigation, flood control, and water supply) and climate change, bringing considerable modifications to the annual flood-pulse of the TSL. Such modifications are expected to have strong impacts on fish biodiversity and abundance. This paper aims to characterize the spatio-temporal variations of fish taxonomic composition and to highlights the underlying determinants of these variations. For this purpose, we used data collected from a community catch monitoring program conducted at six sites during 141 weeks, covering two full hydrological cycles. For each week, we estimated beta diversity as the total variance of the site-by-species community matrix and partitioned it into Local Contribution to Beta Diversity (LCBD) and Species Contribution to Beta Diversity (SCBD). We then performed multiple linear regressions to determine whether species richness, species abundances and water level explained the temporal variation in the contribution of site and species to beta diversity. Our results indicate strong temporal variation of beta diversity due to differential contributions of sites and species to the spatial variation of fish taxonomic composition. We further found that the direction, the shape and the relative effect of species richness, abundances and water level on temporal variation in LCBD and SCBD values greatly varied among sites, thus suggesting spatial variation in the processes leading to temporal variation in community composition. Overall, our results suggest that fish taxonomic composition is not homogeneously distributed over space and time and is likely to be impacted in the future if the flood-pulse dynamic of the system is altered by human activities.

Acute and Chronic Toxicities of TNT and RDX to the Enchytraeid Worm, Enchytraeus crypticus, in Natural Soils

DTIC Science & Technology

2012-11-01

21010-5424 8. PERFORMING ORGANIZATION REPORT NUMBER ECBC-TR-981 9. SPONSORING / MONITORING AGENCY NAME(S) AND ADDRESS(ES) Strategic Environmental ...triazine (RDX) to the potworm Enchytraeus crypticus using the Enchytraeid Reproduction Test (ISO 16387:2004). Studies were designed to identify and...clay loam soils. Toxicity benchmarks established in TSL and SSL will be submitted to the U.S. Environmental Protection Agency Eco-SSL Workgroup for

A Disposable Microfluidic Device for Controlled Drug Release from Thermal-Sensitive Liposomes by High Intensity Focused Ultrasound.

PubMed

Meng, Long; Deng, Zhiting; Niu, Lili; Li, Fei; Yan, Fei; Wu, Junru; Cai, Feiyan; Zheng, Hairong

2015-01-01

The drug release triggered thermally by high intensity focused ultrasound (HIFU) has been considered a promising drug delivery strategy due to its localized energy and non-invasive characters. However, the mechanism underlying the HIFU-mediated drug delivery remains unclear due to its complexity at the cellular level. In this paper, micro-HIFU (MHIFU) generated by a microfluidic device is introduced which is able to control the drug release from temperature-sensitive liposomes (TSL) and evaluate the thermal and mechanical effects of ultrasound on the cellular drug uptake and apoptosis. By simply adjusting the input electrical signal to the device, the temperature of sample can be maintained at 37 °C, 42 °C and 50 °C with the deviation of ± 0.3 °C as desired. The flow cytometry results show that the drug delivery under MHIFU sonication leads to a significant increase in apoptosis compared to the drug release by incubation alone at elevated temperature of 42 °C. Furthermore, increased squamous and protruding structures on the surface membrane of cells were detected by atomic force microscopy (AFM) after MHIFU irradiation of TSL. We demonstrate that compared to the routine HIFU treatment, MHIFU enables monitoring of in situ interactions between the ultrasound and cell in real time. Furthermore, it can quantitatively analyze and characterize the alterations of the cell membrane as a function of the treatment time.

Treating Tooth Surface Loss: Adhesive Restoration of the Worn Anterior Dentition.

PubMed

Patel, Mahul

2016-08-01

The treatment of tooth surface loss (TSL) is becoming more common in primary health care and a diverse variety of patients are presenting with this condition are often being treated by general dental practitioners. This article highlights the importance of comprehensive planning and adept execution that can enhance the patient's outcome and experience. Stages of clinical planning and treatment approaches using a selection of restorative materials utilising various established adhesive clinical techniques will be presented and discussed.

Chicago’s O’Hare Runway Configuration Management System (RCMS). Volume 1. Description of the Operational Software,

DTIC Science & Technology

1987-07-01

9 ...Glossary D-i E- Distribution List E-I D. tSl ’S I hec 3 tttt ,"t!<_-Z. :,,’ e ’: :’ :.,", : - ’,,"/ . .>" ",;’ 9 ’ ’:/’,"" ’,,-’¢’..’:, : ,’-.’ ,.-;.;.;- 4...2 Sheets) 23 6 Foreground Program Flowchart (2 Sheets) 25 7 PF-1 Master Auto Panel 27 8 PF-2 Master Panel 28 9 PF-3 Eligible Current

Gain-Controlled Erbium-Doped Fiber Amplifier Using Mode-Selective Photonic Lantern

DTIC Science & Technology

2016-01-01

schematic diagram of the MSPL integrated with the FM-EDFA is shown in Fig. 3. Two laser diodes (LDs) at λp = 976 nm are connected to the MSPL through a...to co-directionally core pump the FM-EDFA. A tunable semiconductor laser (Santec TSL-210) was used to provide the signal. An optical isolator was...placed in the signal path to avoid spurious optical reflections that could destabilize the laser . In a similar configuration, the delivered signal was

Ballistic Simulation Method for Lithium Ion Batteries (BASIMLIB) Using Thick Shell Composites (TSC) in LS-DYNA

DTIC Science & Technology

2016-08-04

BAllistic SImulation Method for Lithium Ion Batteries (BASIMLIB) using Thick Shell Composites (TSC) in LS-DYNA Venkatesh Babu, Dr. Matt Castanier, Dr...Objective • Objective and focus of this work is to develop a – Robust simulation methodology to model lithium - ion based batteries in its module and full...unlimited  Lithium Ion Phosphate (LiFePO4) battery cell, module and pack was modeled in LS-DYNA using both Thin Shell Layer (TSL) and Thick Shell

A New Diagnostic Resource for Ceratitis capitata Strain Identification Based on QTL Mapping

PubMed Central

Sim, Sheina B.; Ruiz-Arce, Raul; Barr, Norman B.; Geib, Scott M.

2017-01-01

The Mediterranean fruit fly Ceratitis capitata (Wiedemann) is a destructive agricultural pest and the subject of exclusion efforts in many countries. Suppression and eradication of invasive populations to prevent its establishment is facilitated by the release of sterile males using the sterile insect technique (SIT). In SIT release areas, it is critical to accurately discriminate between released sterile males and wild individuals to detect extremely rare invasive individuals in areas inundated with millions of sterile male flies. Current methods for discrimination exist but are not always definitive, and a more reliable method is necessary. To address this, we developed a genotyping assay that can be used to discriminate between sterile males from the SIT strain and wild individuals. This was achieved by identifying single nucleotide polymorphisms (SNPs) linked to the maintained traits that facilitate male-only releases, white pupae (wp) and temperature-sensitive lethal (tsl), via QTL mapping. This resulted in the identification of one SNP that was in near-perfect linkage disequilibrium between genotype at this locus and the pupal color phenotype. Medfly from many SIT colonies and wild individuals from across its geographic range were genotyped for this locus, and results show its consistency in identifying SIT flies. In addition, linkage and QTL mapping of wp and tsl have larger impacts as they can serve as foundational tools to identify the genetic basis of traits that facilitate the separation of males from female flies, which can be used to develop SIT programs in related species. PMID:28889103

Simultaneous determination of triterpenoid saponins in dog plasma by a validated UPLC-MS/MS and its application to a pharmacokinetic study after administration of total saponin of licorice.

PubMed

Tao, Weiwei; Duan, Jinao; Guo, Jianming; Li, Jianping; Tang, Yuping; Liu, Pei; Yang, Nianyun

2013-03-05

A rapid and sensitive ultra performance liquid chromatography-tandem mass spectrometry method was developed for simultaneous determination of eight constituents, uralsaponin C, uralsaponin F, 22β-acetoxyl-glycyrrhizin, 24-hydroxy-licorice-saponin E2, licorice-saponin G2, licorice-saponin E2, glycyrrhizin, and licorice-saponin J2, from total saponin of licorice (TSL) in dog plasma. Ardisiacrispin A was used as the internal standard (IS). The separation was performed on Thermo Syncronic C₁₈ column (100 mm × 2.1 mm, 1.7 μm) at a flow rate of 0.4 mL min⁻¹, and acetonitrile/methanol (3:1, v/v)-0.1% formic acid was used as mobile phase. The detection was performed on a triple quadrupole tandem mass spectrometer by multiple reaction monitoring (MRM) via electrospray ionization (ESI) source with negative ionization mode. All calibration curves had good linearity (r>0.991) over the concentration range from 2.03-405 ng mL⁻¹ to 2.63-2625 ng mL⁻¹ for all components. The intra- and inter-day precision was within 15% and the accuracy ranged from -14.08% to 13.8%. The method was successfully applied to pharmacokinetic study of eight triterpenoid saponins in dog plasma after oral administration of TSL. Crown Copyright © 2012. Published by Elsevier B.V. All rights reserved.

LiMgPO 4:Tb,B - A new sensitive OSL phosphor for dosimetry

NASA Astrophysics Data System (ADS)

Dhabekar, Bhushan; Menon, S. N.; Alagu Raja, E.; Bakshi, A. K.; Singh, A. K.; Chougaonkar, M. P.; Mayya, Y. S.

2011-08-01

Optically Stimulated Luminescence (OSL) technique has emerged as a serious competitor to Thermally Stimulated Luminescence (TSL) technique in various dosimetric applications, especially after the development of crystalline alumina (Al 2O 3:C) doped with carbon. Since then, several attempts are being made to develop other possible materials for OSL based dosimetric applications. Efforts conducted in our laboratory in this direction have led to the development of a new phosphor, Lithium Magnesium Phosphate doped with terbium and boron (LiMgPO 4:Tb,B). This phosphor is prepared by solid-state diffusion method involving conventional air furnaces with operating temperature 1000 °C and easily amenable to large scale production without compromising primary dosimetric advantages. In this work we present some of the dosimetric OSL characteristics of this phosphor. The phosphor exhibits a main TSL peak at 250 °C. The phosphor also emits OSL, when the irradiated phosphor is stimulated with 470 nm light with the OSL sensitivity 1.3 times that of commercially available Al 2O 3:C. Photoluminescence (PL) emission spectrum consists of sharp lines characteristics of Tb 3+ emission. The OSL discs made out of this phosphor are reusable up to at least 50 cycles, the phosphor exhibits dose linearity up to 1 kGy. Minimum detectable dose is found to be 20 μGy and fading of the OSL signal is found to be about 16% in four days, after which the OSL signal stabilizes.

A Kinect based sign language recognition system using spatio-temporal features

NASA Astrophysics Data System (ADS)

Memiş, Abbas; Albayrak, Songül

2013-12-01

This paper presents a sign language recognition system that uses spatio-temporal features on RGB video images and depth maps for dynamic gestures of Turkish Sign Language. Proposed system uses motion differences and accumulation approach for temporal gesture analysis. Motion accumulation method, which is an effective method for temporal domain analysis of gestures, produces an accumulated motion image by combining differences of successive video frames. Then, 2D Discrete Cosine Transform (DCT) is applied to accumulated motion images and temporal domain features transformed into spatial domain. These processes are performed on both RGB images and depth maps separately. DCT coefficients that represent sign gestures are picked up via zigzag scanning and feature vectors are generated. In order to recognize sign gestures, K-Nearest Neighbor classifier with Manhattan distance is performed. Performance of the proposed sign language recognition system is evaluated on a sign database that contains 1002 isolated dynamic signs belongs to 111 words of Turkish Sign Language (TSL) in three different categories. Proposed sign language recognition system has promising success rates.

A Computer Program to Implement the Chen Method of Dimensional Analysis

DTIC Science & Technology

1990-01-01

Director: AXHE-S (m. B Corna)U.S. Army TRADOX Systems Analysis Activity ATTdN: AXrE-IS (Mr. B. Corona) ATM: ATOR-TSL Aberden Proving Ground , MD 21005-5001...Laboratory I Aberdeen Proving Ground , MD 21005-5066 ATTN: AMSMI-ROC Redstone Arsenal, AL 35898-5242 Direct or D U.S. Army Human Engineering Laboratory 1...Kokinakis) U.S. Army Missile Laboratory Aberdeen Proving Ground , MD 21005-5066 ReTN AMSMI-R C1edstone Arsenal, AL 35898-5242 Director Director 1 U.S. Army

Workload, Performance, and Reliability of Digital Computing Systems.

DTIC Science & Technology

1980-12-01

maximized is then P()(tf, ...... , ad .[[. P(ts) h( tf1 ),) (0 42.33) Note that this problem is equivalent to minimazing the function En Jn ,l~~f,) (-X) 1...have been observed at times tf1 , after observing the system since tsl. Take, for instance, the case of the distribution obtained from the simplified...represented by a set of pairs [ts,, tf1 ] i 1 ...... n the maximum likelihood values of a,y,P are these values that maximize the function p(n)( tf1 -ts 1 . . ts

Thermally stimulated luminescence studies of undoped, Cu- and Mn-doped CaSO4 compounds

NASA Astrophysics Data System (ADS)

Manam, J.; Das, S.

Thermally stimulated luminescence (TSL) of undoped and doped CaSO4 with activators such as Cu and Mn has been investigated. The polycrystalline samples of undoped and doped CaSO4 are prepared by the melting method. The formation of CaSO4 compound is confirmed by X-ray diffraction and Fourier transform infrared studies. Scanning electron microscopic studies of CaSO4 are also carried out. The TSL glow curves of undoped CaSO4, Cu- and Mn-doped CaSO4 are studied. Comparison of the thermoluminescence (TL) intensity of the most intensive glow peak of Cu-doped CaSO4 compound with that of undoped CaSO4 shows that addition of Cu impurity in CaSO4 compound enhances the TL intensity by about four times. However, the addition of Mn impurity to undoped CaSO4 increases the TL intensity by about three times when compared with that of undoped CaSO4. The TL-dose dependence of all three samples was studied and was observed to be almost linear in the studied range of irradiation time. Among the samples studied, namely undoped CaSO4 and Cu- and Mn-doped CaSO4, Cu-doped CaSO4 is found to be the most sensitive. The trap parameters, namely order of kinetics (b), activation energy (E) and frequency factor (s) associated with the most intensive glow peaks of CaSO4:Mn, CaSO4:Cu and CaSO4 phosphors were determined using the glow curve shape (Chen's) method.

The Observed Relationship Between Water Vapor and Ozone in the Tropical Tropopause Saturation Layer and the Influence of Meridional Transport

NASA Technical Reports Server (NTRS)

Selkirk, Henry B.; Schoeberl, M. R.; Olsen, M. A.; Douglass, A. R.

2011-01-01

We examine balloonsonde observations of water vapor and ozone from three Ticosonde campaigns over San Jose, Costa Rica [10 N, 84 W] during northern summer and a fourth during northern winter. The data from the summer campaigns show that the uppermost portion of the tropical tropopause layer between 360 and 380 K, which we term the tropopause saturation layer or TSL, is characterized by water vapor mixing ratios from proximately 3 to 15 ppmv and ozone from approximately 50 ppbv to 250 ppbv. In contrast, the atmospheric water vapor tape recorder at 380 K and above displays a more restricted 4-7 ppmv range in water vapor mixing ratio. From this perspective, most of the parcels in the TSL fall into two classes - those that need only additional radiative heating to rise into the tape recorder and those requiring some combination of additional dehydration and mixing with drier air. A substantial fraction of the latter class have ozone mixing ratios greater than 150 ppbv, and with water vapor greater than 7 ppmv this air may well have been transported into the tropics from the middle latitudes in conjunction with high-amplitude equatorial waves. We examine this possibility with both trajectory analysis and transport diagnostics based on HIRDLS ozone data. We apply the same approach to study the winter season. Here a very different regime obtains as the ozone-water vapor scatter diagram of the sonde data shows the stratosphere and troposphere to be clearly demarcated with little evidence of mixing in of middle latitude air parcels.

Bilateral differences in muscle fascicle architecture are not related to the preferred leg in jumping athletes.

PubMed

Aeles, Jeroen; Lenchant, Sietske; Vanlommel, Liesbeth; Vanwanseele, Benedicte

2017-07-01

In many sports, athletes have a preferred leg for sport-specific tasks, such as jumping, which leads to strength differences between both legs, yet the underlying changes in force-generating mechanical properties of the muscle remain unknown. The purpose of this study was to investigate whether the muscle architecture of the medial gastrocnemius (MG) is different between both legs in well-trained jumping athletes and untrained individuals. In addition, we investigated the effect of two ankle joint positions on ultrasound muscle architecture measurements. Muscle architecture of both legs was measured in 16 athletes and 11 untrained individuals at two ankle joint angles: one with the ankle joint in a tendon slack length (TSL) angle and one in a 90° angle. Fascicle lengths and pennation angles at TSL were not different between the preferred and non-preferred legs in either group. The comparison between groups showed no difference in fascicle length, but greater pennation angles were found in the athletes (21.7° ± 0.5°) compared to the untrained individuals (19.8° ± 0.6°). Analyses of the muscle architecture at a 90° angle yielded different results, mainly in the comparison between groups. These results provide only partial support for the notion of training-induced changes in muscle architecture as only differences in pennation angles were found between athletes and untrained individuals. Furthermore, our results provide support to the recommendation to take into account the tension-length relationship and to measure muscle architecture at individually determined tendon slack joint angles.

The Effect of Pre-irradiation Defects on the Recombination Luminescence in Activated Crystals K2SO4

NASA Astrophysics Data System (ADS)

Koketai, Temirgaly; Tagayeva, Batima; Tussupbekova, Ainura; Mussenova, Elmira

The recombinational luminescence of crystals of K2SO4-Mn2+ and K2SO4-Ni2+ is studied in the article. It is established that impurity ions form the radiation induced centers. The cause of changes of the distribution of lightsum on TSL peaks of a matrix is established. It is proposed that it is related to pre-radiation defeсts in crystals. It is established from this effect that ions of Mn2+ and Ni2+ selectively replace cations in a crystal lattice of potassium sulfate.

The direct liquefaction proof of concept program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comolli, A.G.; Lee, L.K.; Pradhan, V.R.

1995-12-31

The goal of the Proof of Concept (POC) Program is to develop Direct Coal Liquefaction and associated transitional technologies towards commercial readiness for economically producing premium liquid fuels from coal in an environmentally acceptable manner. The program focuses on developing the two-stage liquefaction (TSL) process by utilizing geographically strategic feedstocks, commercially feasible catalysts, new prototype equipment, and testing co-processing or alternate feedstocks and improved process configurations. Other high priority objectives include dispersed catalyst studies, demonstrating low rank coal liquefaction without solids deposition, improving distillate yields on a unit reactor volume basis, demonstrating ebullated bed operations while obtaining scale-up data, demonstratingmore » optimum catalyst consumption using new concepts (e.g. regeneration, cascading), producing premium products through on-line hydrotreating, demonstrating improved hydrogen utilization for low rank coals using novel heteroatom removal methods, defining and demonstrating two-stage product properties for upgrading; demonstrating efficient and economic solid separation methods, examining the merits of integrated coal cleaning, demonstrating co-processing, studying interactions between the preheater and first and second-stage reactors, improving process operability by testing and incorporating advanced equipment and instrumentation, and demonstrating operation with alternate coal feedstocks. During the past two years major PDU Proof of Concept runs were completed. POC-1 with Illinois No. 6 coal and POC-2 with Black Thunder sub-bituminous coal. Results from these operations are continuing under review and the products are being further refined and upgraded. This paper will update the results from these operations and discuss future plans for the POC program.« less

Format requirements of thermal neutron scattering data in a nuclear data format to succeed the ENDF format

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, D.

2014-03-31

In November 2012, the Working Party on Evaluation Cooperation Subgroup 38 (WPEC-SG38) began with the task of developing a nuclear data format and supporting infrastructure to replace the now nearly 50 year old ENDF format. The first step in this process is to develop requirements for the new format and infrastructure. In this talk, I will review the status of ENDF's Thermal Scattering Law (TSL) formats as well as support for this data in the GND format (from which the new format is expected to evolve). Finally, I hope to begin a dialog with members of the thermal neutron scatteringmore » community so that their data needs can be accurately and easily accommodated by the new format and tools, as captured by the requirements document. During this discussion, we must keep in mind that the new tools and format must; Support what is in existing data files; Support new things we want to put in data files; and Be flexible enough for us to adapt it to future unanticipated challenges.« less

Modeling and optimization of anaerobic codigestion of potato waste and aquatic weed by response surface methodology and artificial neural network coupled genetic algorithm.

PubMed

Jacob, Samuel; Banerjee, Rintu

2016-08-01

A novel approach to overcome the acidification problem has been attempted in the present study by codigesting industrial potato waste (PW) with Pistia stratiotes (PS, an aquatic weed). The effectiveness of codigestion of the weed and PW was tested in an equal (1:1) proportion by weight with substrate concentration of 5g total solid (TS)/L (2.5gPW+2.5gPS) which resulted in enhancement of methane yield by 76.45% as compared to monodigestion of PW with a positive synergistic effect. Optimization of process parameters was conducted using central composite design (CCD) based response surface methodology (RSM) and artificial neural network (ANN) coupled genetic algorithm (GA) model. Upon comparison of these two optimization techniques, ANN-GA model obtained through feed forward back propagation methodology was found to be efficient and yielded 447.4±21.43LCH4/kgVSfed (0.279gCH4/kgCODvs) which is 6% higher as compared to the CCD-RSM based approach. Copyright © 2016 Elsevier Ltd. All rights reserved.

Epitaxial Growth of LuAG:Ce and LuAG:Ce,Pr Films and Their Scintillation Properties

NASA Astrophysics Data System (ADS)

Douissard, Paul-Antoine; Martin, Thierry; Riva, Federica; Zorenko, Yuriy; Zorenko, Tetiana; Paprocki, Kazimierz; Fedorov, Alexander; Bilski, Pawel; Twardak, Anna

2016-06-01

We performed the growth by Liquid Phase Epitaxy (LPE) of Ce and Ce-Pr doped Lu3Al5O12 (LuAG) Single Crystalline Films (SCFs) onto LuAG and Y3Al5O12 (YAG) substrates. The structural properties of LuAG:Ce and LuAG:Ce,Pr SCFs were examined by X-ray diffraction. The optical properties of the SCFs were studied through cathodoluminescence (CL) spectra, scintillation Light Yield (LY), decay kinetic under α-particle (Pu239) excitation, X-ray excited luminescence, thermostimulated luminescence (TSL) and afterglow measurements. The SCFs grown on LuAG substrates displayed good surface quality and structural perfection, whereas the SCFs grown on YAG substrates showed a rough surface and poorer crystalline quality, due to a large lattice mismatch between the film and the substrate (0.82%). Under α-particle excitation, the LY of LuAG:Ce SCF exceeded by 2 times that of the best YAG:Ce SCF sample used as reference. Under X-ray excitation, the LuAG:Ce SCF with optimized Ce concentration showed LY close (77%) to a reference YAG:Ce Single Crystal (SC) scintillator. The afterglow of LuAG:Ce and LuAG:Ce,Pr SCFs was lower (by 1 decade) than that of the tested reference LuAG:Ce SC. However there is not a complete suppression of the afterglow at room temperature (RT), despite the fact that the SCFs present much lower concentration of antisite and vacancy type defects than their SC counterparts. This can be explained by the presence in the films of other trap centers responsible for TSL above RT.

Final Scientific EFNUDAT Workshop

ScienceCinema

None

2018-05-23

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.euTopics of interest include: Data evaluation Cross section measurements Experimental techniques Uncertainties and covariances Fission properties Current and future facilities ; International Advisory Committee: C. Barreau (CENBG, France)T. Belgya (IKI KFKI, Hungary)E. Gonzalez (CIEMAT, Spain)F. Gunsing (CEA, France)F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany)R. Nolte (PTB, Germany)S. Pomp (TSL UU, Sweden) ;Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco Calviani Samuel Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Losito Vasilis Vlachoudis;Workshop Assistant: Geraldine Jean

Final Scientific EFNUDAT Workshop

ScienceCinema

None

2018-06-20

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.eu. Topics of interest include: Data evaluation, Cross section measurements, Experimental techniques, Uncertainties and covariances, Fission properties, and Current and future facilities. International Advisory Committee: C. Barreau (CENBG, France), T. Belgya (IKI KFKI, Hungary), E. Gonzalez (CIEMAT, Spain), F. Gunsing (CEA, France), F.-J. Hambsch (IRMM, Belgium), A. Junghans (FZD, Germany), R. Nolte (PTB, Germany)S. Pomp (TSL UU, Sweden) Workshop Organizing Committee: Enrico Chiaveri (Chairman), Marco Calviani, Samuel Andriamonje, Eric Berthoumieux, Carlos Guerrero, Roberto Losito, Vasilis Vlachoudis. Workshop Assistant: Geraldine Jean

Final Scientific EFNUDAT Workshop

ScienceCinema

Garbil, Roger

2018-04-16

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.eu. Topics of interest include: Data evaluation; Cross section measurements; Experimental techniques; Uncertainties and covariances; Fission properties; Current and future facilities. International Advisory Committee: C. Barreau (CENBG, France)T. Belgya (IKI KFKI, Hungary)E. Gonzalez (CIEMAT, Spain)F. Gunsing (CEA, France)F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany)R. Nolte (PTB, Germany)S. Pomp (TSL UU, Sweden). Workshop Organizing Committee: Enrico Chiaveri (Chairman); Marco Calviani; Samuel Andriamonje; Eric Berthoumieux; Carlos Guerrero; Roberto Losito; Vasilis Vlachoudis; Workshop Assistant: Geraldine Jean

Final Scientific EFNUDAT Workshop

ScienceCinema

Lantz, Mattias; Neudecker, Denise

2018-05-25

Part 5 of The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.euTopics of interest include: Data evaluation Cross section measurements Experimental techniques Uncertainties and covariances Fission properties Current and future facilities International Advisory Committee: C. Barreau (CENBG, France) T. Belgya (IKI KFKI, Hungary)E. Gonzalez (CIEMAT, Spain) F. Gunsing (CEA, France)F.-J. Hambsch (IRMM, Belgium) A. Junghans (FZD, Germany) R. Nolte (PTB, Germany) S. Pomp (TSL UU, Sweden) Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco Calviani Samuel Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Losito Vasilis Vlachoudis Workshop Assistant: Geraldine Jean

Final Scientific EFNUDAT Workshop

ScienceCinema

Wilson, J.N.

2018-05-24

Part 7 of The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive.EFNUDAT website: http://www.efnudat.euTopics of interest include: Data evaluation; Cross section measurements; Experimental techniques; Uncertainties and covariances; Fission properties; Current and future facilities;International Advisory Committee: C. Barreau (CENBG, France) T. Belgya (IKI KFKI, Hungary) E. Gonzalez (CIEMAT, Spain) F. Gunsing (CEA, France) F.-J. Hambsch (IRMM, Belgium) A. Junghans (FZD, Germany) R. Nolte (PTB, Germany) S. Pomp (TSL UU, Sweden) Workshop Organizing Committee: Enrico Chiaveri (Chairman) Marco Calviani Samuel Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Losito Vasilis Vlachoudis Workshop Assistant: Geraldine Jean.

(n,xn) cross section measurements for Y-89 foils used as detectors for high energy neutron measurements in the deeply subcritical assembly "QUINTA"

NASA Astrophysics Data System (ADS)

Bielewicz, Marcin; Kilim, Stanisław; Strugalska-Gola, Elżbieta; Szuta, Marcin; Wojciechowski, Andrzej; Tyutyunnikov, Sergey; Prokofiev, Alexander; Passoth, Elke

2017-09-01

Study of the deep subcritical systems (QUINTA) using relativistic beams is performed within the project "Energy and Transmutation of Radioactive Wastes" (E&T - RAW). The experiment assembly was irradiated by deuteron/proton beam (Dubna NUCLOTRON). We calculated the neutron energy spectrum inside the whole assembly by using threshold energy (n,xn) reactions in yttrium (Y-89) foils. There are almost no experimental cross section data for those reactions. New Y-89(n,xn) cross section measurements were carried out at The Svedberg laboratory (TSL) in Uppsala, Sweden in 2015. In this paper we present preliminary results of those experiments.

Final Scientific EFNUDAT Workshop

ScienceCinema

None

2018-05-24

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.eu. Topics of interest include: Data evaluation; Cross section measurements; Experimental techniques; Uncertainties and covariances; Fission properties; Current and future facilities. International Advisory Committee: C. Barreau (CENBG, France) T. Belgya (IKI KFKI, Hungary) E. Gonzalez (CIEMAT, Spain) F. Gunsing (CEA, France) F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany) R. Nolte (PTB, Germany) S. Pomp (TSL UU, Sweden) & Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco Calviani Samuel Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Losito Vasilis Vlachoudis; Workshop Assistant: Geraldine Jean

X-ray induced luminescence properties of (Y,Eu)AlO3 single crystals

NASA Astrophysics Data System (ADS)

Kuro, Tomoaki; Nakauchi, Daisuke; Okada, Go; Kawaguchi, Noriaki; Yanagida, Takayuki

2017-02-01

We investigated photoluminescence, scintillation and dosimeter properties of (Y1-x Eux)AlO3 (x = 0.001, 0.5 and 1) single crystals (hereafter denoted as Eu:YAP for x = 0.001, EYAP for x = 0.5 and EAP for x = 1). The samples were prepared by the Floating Zone method. In photoluminescence (PL), we observed a broad emission around 300-400 nm due to host under excitation of 280 nm, and emissions due to the 4f state transitions of Eu3+ appeared around 590 nm and 615 nm. Scintillation spectra also show emission peaks around 590 and 615 nm due to the 4f state transitions of Eu3+ in all the samples. In addition, emissions around 300-400 nm due to YAP host and around 550-700 nm due to 5d-4f transitions of Eu2+ appeared in Eu:YAP. The PL and scintillation decay time profiles consisted of several exponential decay components. The fast (ns) component group was possibly due to host emission, and especially Eu:YAP demonstrated a very fast PL decay time of 16 ns. The intermediate (μs) component group was due to the 5d-4f transitions of Eu2+. The slow (ms) component group was ascribed to the 4f state transitions of Eu3+ ion. The Eu:YAP sample showed intense thermally-stimulated luminescence (TSL) with peaks at 46, 155, 255 and 443 °C. The intensity was much higher than those of EAP and EYAP. In particular, the peak at 254 °C, which showed the highest intensity, was due to doping with Eu. The TSL dose response function showed a good linearity (R2 > 0.99) over a wide dose range from 0.1 mGy to 100 mGy for Eu:YAP, which showed the highest sensitivity among the present samples.

Lipogels responsive to near-infrared light for the triggered release of therapeutic agents.

PubMed

Martín-Saavedra, Francisco; Ruiz-Hernández, Eduardo; Escudero-Duch, Clara; Prieto, Martín; Arruebo, Manuel; Sadeghi, Negar; Deckers, Roel; Storm, Gert; Hennink, Wim E; Santamaría, Jesús; Vilaboa, Nuria

2017-10-01

Here we report a composite system based on fibrin hydrogels that incorporate in their structure near-infrared (NIR) responsive nanomaterials and thermosensitive liposomes (TSL). Polymerized fibrin networks entrap simultaneously gold-based nanoparticles (NPs) capable of transducing NIR photon energy into heat, and lysolipid-incorporated TSL (LTSL) loaded with doxorubicin hydrochloride (DOX). NIR irradiation of the resulting hydrogels (referred to as "lipogels") with 808nm laser light increased the temperature of the illuminated areas, leading to the release of the liposomal cargo. Levels of DOX that release from the "smart" composites were dependent on the concentration of NIR nanotransducers loaded in the lipogel, the intensity of the electromagnetic energy deposited and the irradiation regime. Released DOX retained its bioactivity, as shown in cultures of epithelial carcinoma cells. Finally, the developed drug delivery platform was refined by using NIR-photoabsorbers based on copper sulfide NPs to generate completely biodegradable composites as well as through the incorporation of cholesterol (Ch) in LTSL formulation, which lessens leakiness of the liposomal cargo at physiological temperature. This remotely controlled system may suit well for those therapies that require precise control over the dose of delivered drug in a defined spatiotemporal framework. Hydrogels composed of fibrin embedding nanoparticles responsive to near infrared (NIR) energy and thermosensitive liposomes loaded with doxorubicin hydrochloride (DOX), were prepared by in situ polymerization. NIR-light irradiation of these constructs, referred to as "NIR responsive lipogels", results in the controlled release of DOX to the surrounding medium. This technology may use fully degradable components and can preserve the bioactivity of liposomal cargo after remote triggering to finely regulate the dose and bioavailability of delivered payloads. NIR responsive lipogels technology overcomes the limitations of drug release systems based on the combination of liposomes and degradable polymeric materials, which in many cases lead to insufficient release at therapy onset or to overdose during high degradation period. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Final Scientific EFNUDAT Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garbil, Roger

2010-11-09

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.eu. Topics of interest include: Data evaluation; Cross section measurements; Experimental techniques; Uncertainties and covariances; Fission properties; Current and future facilities. International Advisory Committee: C. Barreau (CENBG, France)T. Belgya (IKI KFKI, Hungary)E. Gonzalez (CIEMAT, Spain)F. Gunsing (CEA, France)F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany)R. Nolte (PTB, Germany)S. Pomp (TSL UU, Sweden). Workshop Organizing Committee: Enrico Chiaveri (Chairman); Marco Calviani; Samuel Andriamonje; Eric Berthoumieux; Carlos Guerrero; Robertomore » Losito; Vasilis Vlachoudis; Workshop Assistant: Geraldine Jean« less

Final Scientific EFNUDAT Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, J.N.

2010-11-09

Part 7 of The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive.EFNUDAT website: http://www.efnudat.euTopics of interest include: Data evaluation; Cross section measurements; Experimental techniques; Uncertainties and covariances; Fission properties; Current and future facilities;International Advisory Committee: C. Barreau (CENBG, France) T. Belgya (IKI KFKI, Hungary) E. Gonzalez (CIEMAT, Spain) F. Gunsing (CEA, France) F.-J. Hambsch (IRMM, Belgium) A. Junghans (FZD, Germany) R. Nolte (PTB, Germany) S. Pomp (TSL UU, Sweden) Workshop Organizing Committee: Enrico Chiaveri (Chairman) Marco Calvianimore » Samuel Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Losito Vasilis Vlachoudis Workshop Assistant: Geraldine Jean.« less

Final Scientific EFNUDAT Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lantz, Mattias; Neudecker, Denise

2010-11-09

Part 5 of The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.euTopics of interest include: Data evaluation Cross section measurements Experimental techniques Uncertainties and covariances Fission properties Current and future facilities International Advisory Committee: C. Barreau (CENBG, France) T. Belgya (IKI KFKI, Hungary)E. Gonzalez (CIEMAT, Spain) F. Gunsing (CEA, France)F.-J. Hambsch (IRMM, Belgium) A. Junghans (FZD, Germany) R. Nolte (PTB, Germany) S. Pomp (TSL UU, Sweden) Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco Calviani Samuelmore » Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Losito Vasilis Vlachoudis Workshop Assistant: Geraldine Jean« less

Final Scientific EFNUDAT Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vlachoudis, Vasilis

2010-11-09

Part 8. The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.eu Topics of interest include: Data evaluation Cross section measurements Experimental techniques Uncertainties and covariances Fission properties Current and future facilities International Advisory Committee: C. Barreau (CENBG, France)T. Belgya (IKI KFKI, Hungary) E. Gonzalez (CIEMAT, Spain)F. Gunsing (CEA, France) F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany) R. Nolte (PTB, Germany)S. Pomp (TSL UU, Sweden) Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco Calviani Samuel Andriamonje Ericmore » Berthoumieux Carlos Guerrero Roberto LositoVasilis Vlachoudis Workshop Assistant: Geraldine Jean« less

Final Scientific EFNUDAT Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2010-11-09

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.eu. Topics of interest include: Data evaluation; Cross section measurements; Experimental techniques; Uncertainties and covariances; Fission properties; Current and future facilities. International Advisory Committee: C. Barreau (CENBG, France) T. Belgya (IKI KFKI, Hungary) E. Gonzalez (CIEMAT, Spain) F. Gunsing (CEA, France) F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany) R. Nolte (PTB, Germany) S. Pomp (TSL UU, Sweden) & Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco Calviani Samuelmore » Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Losito Vasilis Vlachoudis; Workshop Assistant: Geraldine Jean« less

Final Scientific EFNUDAT Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2010-11-09

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive. EFNUDAT website: http://www.efnudat.euTopics of interest include: Data evaluation Cross section measurements Experimental techniques Uncertainties and covariances Fission properties Current and future facilities ; International Advisory Committee: C. Barreau (CENBG, France)T. Belgya (IKI KFKI, Hungary)E. Gonzalez (CIEMAT, Spain)F. Gunsing (CEA, France)F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany)R. Nolte (PTB, Germany)S. Pomp (TSL UU, Sweden) ;Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco Calviani Samuel Andriamonje Eric Berthoumieux Carlos Guerrero Roberto Lositomore » Vasilis Vlachoudis;Workshop Assistant: Geraldine Jean« less

Final Scientific EFNUDAT Workshop

ScienceCinema

None

2017-12-09

The Final Scientific EFNUDAT Workshop - organized by the CERN/EN-STI group on behalf of n_TOF Collaboration - will be held at CERN, Geneva (Switzerland) from 30 August to 2 September 2010 inclusive.EFNUDAT website: http://www.efnudat.euTopics of interest include: Data evaluationCross section measurementsExperimental techniquesUncertainties and covariancesFission propertiesCurrent and future facilities  International Advisory Committee: C. Barreau (CENBG, France)T. Belgya (IKI KFKI, Hungary)E. Gonzalez (CIEMAT, Spain)F. Gunsing (CEA, France)F.-J. Hambsch (IRMM, Belgium)A. Junghans (FZD, Germany)R. Nolte (PTB, Germany)S. Pomp (TSL UU, Sweden) Workshop Organizing Committee: Enrico Chiaveri (Chairman)Marco CalvianiSamuel AndriamonjeEric BerthoumieuxCarlos GuerreroRoberto LositoVasilis Vlachoudis Workshop Assistant: Géraldine Jean

Comittees

NASA Astrophysics Data System (ADS)

2004-10-01

Fritz Caspers (CERN, Switzerland), Michel Chanel (CERN, Switzerland), Håkan Danared (MSL, Sweden), Bernhard Franzke (GSI, Germany), Manfred Grieser (MPI für Kernphysik, Germany), Dieter Habs (LMU München, Germany), Jeffrey Hangst (University of Aarhus, Denmark), Takeshi Katayama (RIKEN/Univ. Tokyo, Japan), H.-Jürgen Kluge (GSI, Germany), Shyh-Yuan Lee (Indiana University, USA), Rudolf Maier (FZ Jülich, Germany), John Marriner (FNAL, USA), Igor Meshkov (JINR, Russia), Dieter Möhl (CERN, Switzerland), Vasily Parkhomchuk (BINP, Russia), Robert Pollock (Indiana University), Dieter Prasuhn (FZ Jülich, Germany), Dag Reistad (TSL, Sweden), John Schiffer (ANL, USA), Andrew Sessler (LBNL, USA), Alexander Skrinsky (BINP, Russia), Markus Steck (GSI, Germany), Jie Wei (BNL, USA), Andreas Wolf (MPI für Kernphysik, Germany), Hongwei Zhao (IMP, People's Rep. of China).

Simulation of fatigue damage in ferroelectric polycrystals under mechanical/electrical loading

NASA Astrophysics Data System (ADS)

Kozinov, S.; Kuna, M.

2018-07-01

The reliability of smart-structures made of ferroelectric ceramics is essentially reduced by the formation of cracks under the action of external electrical and/or mechanical loading. In the current research a numerical model for low-cycle fatigue in ferroelectric mesostructures is proposed. In the finite element simulations a combination of two user element routines is utilized. The first one is used to model a micromechanical ferroelectric domain switching behavior inside the grains. The second one is used to simulate fatigue damage of grain boundaries by a cohesive zone model (EMCCZM) based on an electromechanical cyclic traction-separation law (TSL). For numerical simulations a scanning electron microscope image of the ceramic's grain structure was digitalized and meshed. The response of this mesostructure to cyclic electrical or mechanical loading is systematically analyzed. As a result of the simulations, the distribution of electric potential, field, displacement and polarization as well as mechanical stresses and deformations inside the grains are obtained. At the grain boundaries, the formation and evolution of damage are analyzed until final failure and induced degradation of electric permittivity. It is found that the proposed model correctly mimics polycrystalline behavior during poling processes and progressive damage under cyclic electromechanical loading. To the authors' knowledge, it is the first model and numerical analysis of ferroelectric polycrystals taking into account both domain reorientation and cohesive modeling of intergranular fracture. It can help to understand failure mechanisms taking place in ferroelectrics during fatigue processes.

Studying monogenetic volcanoes with Terrestrial Laser Scanner: Case study at Croscat volcano (Garrotxa Volcanic Zone, Spain)

NASA Astrophysics Data System (ADS)

Geyer Traver, A.; Garcia-Selles, D.; Peddrazzi, D.; Barde-Cabusson, S.; Marti, J.; Muñoz, J.

2013-12-01

Monogenetic basaltic zones are common in many volcanic environments and may develop under very different geodynamic conditions. Despite existing clear similarities between the eruptive activity of different monogenetic volcanic fields, important distinctions may arise when investigating in detail the individual eruptive sequences. Interpretation of the deposits and consequently, the reconstruction and characterization of these eruptive sequences is crucial to evaluate the potential hazard in case of active areas. In diverse occasions, erosional processes (natural and/or anthropogenic) may partly destroy these relatively small-sized volcanic edifices exposing their internal parts. Furthermore, despite human activity in volcanic areas is sometimes unimportant due to the remote location of the monogenetic cones, there are places where this form of erosion is significant, e.g. Croscat volcano (Catalan Volcanic Field, Spain). In any case, when studying monogenetic volcanism, it is usual to find outcrops where the internal structure of the edifices is, for one or other reason, well exposed. However, the access to these outcrops may be extremely difficult or even impossible. During the last years, it has been demonstrated that the study of outcrops with problematic or completely restricted access can be carried out by means of digital representations of the outcrop surface. Digital outcrops make possible the study of those areas with natural access limitations or safety issues and may facilitate visualization of the features of interest over the entire outcrop, as long as the digital outcrop can be analysed while navigated in real- time, with optional displays for perspective, scale distortions, and attribute filtering. In particular, Terrestrial Laser Scanning (TSL) instruments using Light Detection And Ranging technology (LIDAR) are capable of capturing topographic details and achieve modelling accuracy within a few centimetres. The data obtained enables the creation of detailed 3-D terrain models of greater coverage and accuracy than conventional methods and with almost complete safety of the operators. Here we want to introduce the TSL methodology to the volcanological community. We show how data obtained with this tool may be useful, not only for volcano monitoring purposes, but also to perform the description of the internal structure of exposed volcanic edifices. A further useful application is the estimate of erosion rates and patterns that may be helpful in terms of hazard assessment or preservation of volcanic landscapes. We use as an example of application the Croscat volcano, a monogenetic edifice of the La Garrotxa volcanic field (Spain), which quarrying jobs have exposed the internal part of the volcano leading to a perfect view of its interior but making difficult the access to the upper parts. The Croscat volcano is additionally one of the most emblematic symbols of the La Garrotxa Volcanic Zone Natural Park being its preservation a main target of the park administration.

Investigation of Particle Accumulation, Chemosensitivity and Thermosensitivity for Effective Solid Tumor Therapy Using Thermosensitive Liposomes and Hyperthermia.

PubMed

Lokerse, Wouter J M; Bolkestein, Michiel; Ten Hagen, Timo L M; de Jong, Marion; Eggermont, Alexander M M; Grüll, Holger; Koning, Gerben A

2016-01-01

Doxorubicin (Dox) loaded thermosensitive liposomes (TSLs) have shown promising results for hyperthermia-induced local drug delivery to solid tumors. Typically, the tumor is heated to hyperthermic temperatures (41-42 °C), which induced intravascular drug release from TSLs within the tumor tissue leading to high local drug concentrations (1-step delivery protocol). Next to providing a trigger for drug release, hyperthermia (HT) has been shown to be cytotoxic to tumor tissue, to enhance chemosensitivity and to increase particle extravasation from the vasculature into the tumor interstitial space. The latter can be exploited for a 2-step delivery protocol, where HT is applied prior to i.v. TSL injection to enhance tumor uptake, and after 4 hours waiting time for a second time to induce drug release. In this study, we compare the 1- and 2-step delivery protocols and investigate which factors are of importance for a therapeutic response. In murine B16 melanoma and BFS-1 sarcoma cell lines, HT induced an enhanced Dox uptake in 2D and 3D models, resulting in enhanced chemosensitivity. In vivo, therapeutic efficacy studies were performed for both tumor models, showing a therapeutic response for only the 1-step delivery protocol. SPECT/CT imaging allowed quantification of the liposomal accumulation in both tumor models at physiological temperatures and after a HT treatment. A simple two compartment model was used to derive respective rates for liposomal uptake, washout and retention, showing that the B16 model has a twofold higher liposomal uptake compared to the BFS-1 tumor. HT increases uptake and retention of liposomes in both tumors models by the same factor of 1.66 maintaining the absolute differences between the two models. Histology showed that HT induced apoptosis, blood vessel integrity and interstitial structures are important factors for TSL accumulation in the investigated tumor types. However, modeling data indicated that the intraliposomal Dox fraction did not reach therapeutic relevant concentrations in the tumor tissue in a 2-step delivery protocol due to the leaking of the drug from its liposomal carrier providing an explanation for the observed lack of efficacy.

Mobilitätslösungen für den ländlichen Raum. Das Beispiel VSB Verkehrsverbund Schwarzwald-Baar in Baden-Württemberg

NASA Astrophysics Data System (ADS)

Mager, Thomas J.

2017-09-01

The current public transport situation in rural areas is characterized by strong changes in legal, economic, demographic and above all political influence factors. In Baden-Württemberg, student transportation funding has changed as part of the municipalization of compensation payments pursuant to § 45a of the Public Transportation Act. This will affect public transportation in rural areas, especially in the southern Baden region, which accounts for 80% of all rural public transportation. In order to maintain public transportation in rural areas, new models of long-term financing independent of student numbers should be developed and applied in combination with alternative and less traditional service offerings. This article discusses the example of the VSB transport association Schwarzwald-Baar, which offers mobility solutions in rural areas.

The Schome Park Programme: Exploring Educational Alternatives

NASA Astrophysics Data System (ADS)

Twining, Peter; Footring, Shri

The Schome Park Programme set out to extend thinking about what the education system for the information age (Schome) should be like. The first three phases of the programme spanned 13 months and involved the use of Schome Park, our "closed" island(s) in Teen Second LifeTM (TSL) virtual world alongside a wiki and forum. During this time approximately two hundred 13-17 year olds and around 50 adults were given access to Schome Park. Having explained the context in which this work took place the paper outlines the initial educational design underpinning the programme and describes some of the activities which took place. It goes on to explore some dimensions of practice which emerged from the data analysis towards the end of Phase 3, focusing on learner experiences of experimentation, playfulness, curriculum, choice, participation and the expression of the learner voice.

Localised states in organic semiconductors and their detection

NASA Astrophysics Data System (ADS)

Imperia, Paolo

2002-06-01

New polymers and low molecular compounds, suitable for organic light emitting devices and organic electronic applications, have been synthesised in this years in order to obtain electron transport characteristics compatible with requirements for applications in real plastic devices. However, despite of the technological importance and of the relevant progress in devices manufacture, fundamental physical properties of such class of materials are still not enough studied. In particular extensive presence of distributions of localised states inside the band gap has a deep impact on their electronic properties. Such presence of shallow traps as well as the influence of the sample preparation conditions on deep and shallow localised states have not been, until now, systematically explored. The thermal techniques are powerful tools in order to study localised levels in inorganic and organic materials. Thermally stimulated luminescence (TSL), thermally stimulated currents (TSC) and thermally stimulated depolarisation currents (TSDC) allow to deeply look to shallow and deep trap levels as well as they permit to study, in synergy with dielectric spectroscopy (DES), polarisation and depolarisation effects. We studied, by means of numerical simulations, the first and the second order kinetic equations characterised by negligible and strong re-trapping respectively. We included in the equations Gaussian, exponential and quasi-continuous distributions of localised states. The shapes of the theoretical peaks have been investigated by means of systematic variation of the two main parameters of the equations, i. e. the energy trap depth E and the frequency factor a and of the parameters regulating the distributions, in particular for a Gaussian distribution the distribution width s and the integration limits. The theoretical findings have been applied to experimental glow curves. Thin films of polymers and low molecular compounds. Polyphenylquinoxalines, trisphenylquinoxalines and oxadiazoles, studied because of their technological relevance, show complex thermograms, having several levels of localised states and depolarisation peaks. In particular well ordered films of an amphiphilic substituted 2-(p-nitrophenyl)-5-(p-undecylamidophenyl)-1,3,4-oxadiazole (NADPO) are characterised by rich TSL thermograms. A wide region of shallow traps, localised at Em = 4 meV, has been successfully fit by means of a first order kinetic equation having a Gaussian distribution of localised states. Two further peaks, having a different origin, have been characterised. The peaks at Tm = 221.5 K and Tm = 254.2 have activation energy of Em= 0.63 eV and Em = 0.66 eV, frequency factor s = 2.4x1012 s-1 and s = 1.85x1011 s-1, distribution width s = 0.045 eV and s = 0.088 eV respectively. Increasing the number of thermal cycle, a peak, probably connected with structural defects, appears at Tm = 197.7 K. The numerical analysis of this peak was performed by means of a first order equation containing a Gaussian distribution of traps. The activation energy of the trap level is centred at Em = 0.55 eV. The distribution is perfectly symmetric with a quite small width s = 0.028 eV. The frequency factor is s = 1.15 x 1012 s-1, resulting of the same order of magnitude of its neighbour peak at Tm = 221.5 K, having both, probably, the same origin. Furthermore the work demonstrates that the shape of the glow curves is strongly influenced by the excitation temperature and by the thermal cycles. For that reason Gaussian distributions of localised states can be confused with exponential distributions if the previous thermal history of the samples is not adequately considered. In den letzten Jahren ist eine Vielzahl neuer organischer Polymere und niedermolekularer Verbindungen synthetisiert worden, die sich als aktive Komponente für Elektrolumineszenz-Bauelemente und andere elektronische Anwendungen eignen. Trotz der großen technologischen Bedeutung und des erheblichen Fortschrittes, der bei der Herstellung solcher Materialien erzielt worden ist, sind grundlegende physikalische Eigenschaften dieser Materialklassen noch nicht ausreichend erforscht. Insbesondere das Auftreten lokalisierter Zustände innerhalb der Bandlücke hat besondere Bedeutung für ihre elektronischen Eigenschaften. Sowohl die Präsenz dieser flachen traps (Fallen, Löcher) als auch der Einfluß der Herstellungsbedingungen auf die tiefen und flachen lokalisierten Zustände wurden bisher nicht systematisch untersucht. Thermische Techniken sind wichtige Methoden, um lokalisierte Niveaus in organischen und anorganischen Materialien zu erforschen. Themisch-Stimulierte Lumineszenz (TSL), Thermisch-Stimulierte Ströme (TSC) und Thermisch-Stimulierte Depolarisierte Ströme (TSDC) ermöglichen die Untersuchung flacher und tiefer traps; in Verbindung mit DiElektrischer Spektroskopie (DES) können außerdem Polarisations- und Depolarisationseffekte studiert werden. Mit Hilfe numerischer Simulationen haben wir die kinetischen Gleichungen erster und zweiter Ordnung untersucht, die sich durch schwaches bzw. starkes Wieder-Fangen beschreiben lassen. In diesen Gleichungen haben wir Gaussian-, exponentielle und quasi-kontinuierliche Verteilungen von lokalisierten Zustände berücksichtigt. Durch Veränderung der beiden wichtigsten Parameter (Tiefe der traps E und Häufigkeit) konnte die Form der thermischen Maxima untersucht werden. Auch die die Gaussian-Verteilung bestimmenden Faktoren wurden verändert. Diese theoretischen Ergebnisse wurden auf die experimentellen Glow-Kurven angewandt. Dünne Filme aus polymeren und niedermolekularen Verbindungen (Polyphenylquinoxaline, Trisphenylquinoxaline und Oxadiazole), die wegen ihrer technologischen Bedeutung ausgewählt wurden, zeigen komplexes thermisches Verhalten. Insbesondere hoch geordnete Filme eines amphiphil substituierten 2-(p-nitrophenyl)-5-(p-undecylamidophenyl)-1,3,4-oxadiazols (NADPO) zeichnen sich durch komplexe TSL-Diagramme aus. Im Bereich von Em = 4 meV wurde eine Region flacher traps gefunden. Zwei weitere TSL-Maxima treten bei Tm = 221.5 K bzw. Tm = 254.2 K auf. Sie besitzen Aktivierungsenergien von Em= 0.63 eV bzw. Em = 0.66 eV, ihre Frequenzfaktoren betragen s = 2.4x1012 s-1 bzw. s = 1.85x1011 s-1, sie zeigen Breiten der Verteilung von s = 0.045 eV bzw. s = 0.088 eV. Des weiteren zeigt diese Arbeit, daß die Form der Glow-Kurven stark von der Anregungstemperatur und vom thermischen Kreislauf beeinflußt wird.

Study of the ultraviolet emission of the electrode coatings of arc welding.

PubMed

Garcia-Guinea, J; Correcher, V; Lombardero, M; Gonzalez-Martin, R

2004-08-01

The optical emission properties of several minerals components employed in electrode coatings of arc welding have been investigated. The X-ray diffraction analysis shows that the composition of 14 commercial electrode coatings collected from different countries (Spain, France, UK, Poland, Argentina and Germany), consists of quartz, calcite, sodium and potassium rich feldspars, muscovite and rutile. The natural thermal stimulated luminescence (TSL) of these mineral phases, measured in the range of 200-800 nm at different temperatures (from room temperature to 400 degrees C) displays UV-A (wavelengths of 320 nm to 400 nm) and UV-B (from 280 nm to 320 nm) emissions, with the exception of rutile. The UV-B radiation, commonly described as the most dangerous form of radiation to human life, is here associated with structural defects in the crystallographic lattice of the mineral components of electrode coatings.

The Kinetics of Polymer Cure by Differential Scanning Calorimetry. Volume I

DTIC Science & Technology

1982-05-01

29 AFWAL-TR-81-4177 Volume I KINETIC *9*dL.15.10.1,.3 GULF ATS AKXIUfUM OkUINATE- L07.0 OCCURS AT 51,j.UO EG KELVIN. PtAA SEARCH LIMITS: STAAT PT...4177 Vol tne I tSL.15p.i0.14.1 GULF ATS 8U. t -3090-0U79-O0b 6-00 9-0 A2-0O01#-0O’t-00 #a -j 047-004900O5 Z-OSJ-05 0056-CbOO00 bt -30a2-00e63-005 5-0064...0093 U1.15.10.14.2 GULF &TS 4.01 ZO.0 410.0 323.0 L.7 -j160DL0180019-0164-0161-0186-0154- 0 I6 3 -,3182-L62-018Z-0163-01b3-01b401S~4O1Oo4 -) 165-0185

A study of inter-crystallite spaces in some polycrystalline inorganic systems using positron annihilation lifetime spectroscopy

NASA Astrophysics Data System (ADS)

Shantarovich, V. P.; Suzuki, T.; Ito, Y.; Kondo, K.; Gustov, V. W.; Melikhov, I. V.; Berdonosov, S. S.; Ivanov, L. N.; Yu, R. S.

2007-02-01

Positron annihilation lifetime spectroscopy (PALS) was used for calculation of number density and effective sizes of free volume holes (inter-crystallite spaces) in polycrystal CaSO 4, CaCO 3 (vaterit) and Ca 10(PO 4) 6(OH) 2 (apatite). The effect of substitution of two-valence Ca(II) for three-valence Eu(III) on annihilation characteristics of apatite, studied together with the data on thermo-stimulated luminescence (TSL) and low-temperature sorption of gas (N 2), helped to elucidate mechanism of positronium atom (Ps) localization in the free volume holes and perform corresponding calculations. It came out that PALS is more sensitive to inter-crystallite sites (10 16 cm -3) in polycrystallites than to the free volume holes in polymer glasses (10 19 cm -3). This is due to higher mobility of the precursor of localized Ps in crystallites.

DOE technical standards list: Directory of DOE and contractor personnel involved in non-government standards activities

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-08-01

The body of this document contains a listing of DOE employees and DOE contractors who have submitted form DOE F 1300.2, Record of Non-Government Standards Activity, which is attached to the end of this document and to DOE Order 1300.2A. Additional names were added from rosters supplied by non-Government standards bodies. The committees or governing bodies in which the person participates is listed after each name. An asterisk preceding the committee notation indicates that the person has identified himself or herself as the DOE representative on that committee. Appendices to this document are also provided to sort the information bymore » the parent employment organization, by non-Government standards activity, and by the proper names of the non-Government standards organizations and committees. DOE employees and contractors listed in this TSL are those recorded as of July 1, 1996.« less

Energy Consumption in Copper Smelting: A New Asian Horse in the Race

NASA Astrophysics Data System (ADS)

Coursol, P.; Mackey, P. J.; Kapusta, J. P. T.; Valencia, N. Cardona

2015-05-01

After a marked improvement in energy consumption in copper smelting during the past few decades, technology development has been slowing down in the Americas and in Europe. Innovation, however, is still required to further reduce energy consumption while complying with stringent environmental regulations. The bottom blowing smelting technology being developed in China shows success and promise. The general configuration of the bath smelting vessel, the design of high-pressure injectors, and the concentrate addition system are described and discussed in this article with respect to those used in other technologies. The bottom blowing technology is shown to be operating at a temperature in the range of 1160-1180°C, which is the lowest reported temperature range for a modern copper smelting process. In this article, it is suggested that top feeding of filter cake concentrate, which is also used in other technologies, has a positive effect in reducing the oxidation potential of the slag ( p(O2)) while increasing the FeS solubility in slag. This reduction in p(O2) lowers the magnetite liquidus of the slag, while the increased solubility of FeS in slag helps toward reaching very low copper levels in flotation slag tailings. The application of high-pressure injectors allows for the use of high levels of oxygen enrichment with no requirements for punching. Using a standard modeling approach from the authors' previous studies, this article discusses these aspects and compares the energy consumption of the bottom blowing technology with that of other leading flash and bath smelting technologies, namely: flash smelting, Noranda/Teniente Converter, TSL (Isasmelt [Glencore Technology Pty. Ltd., Brisbane, Queensland, Australia]/Outotec), and the Mitsubishi Process (Mitsubishi Materials Corporation, Tokyo, Japan).

Cryopreservation of Embryos of the Mediterranean Fruit Fly Ceratitis capitata Vienna 8 Genetic Sexing Strain

PubMed Central

Augustinos, Antonios A.; Rajamohan, Arun; Kyritsis, Georgios A.; Zacharopoulou, Antigone; Haq, Ihsan ul; Targovska, Asya; Caceres, Carlos; Bourtzis, Kostas; Abd-Alla, Adly M. M.

2016-01-01

The Mediterranean fruit fly, Ceratitis capitata, is one of the most serious pests of fruit crops world-wide. During the last decades, area-wide pest management (AW-IPM) approaches with a sterile insect technique (SIT) component have been used to control populations of this pest in an effective and environment-friendly manner. The development of genetic sexing strains (GSS), such as the Vienna 8 strain, has been played a major role in increasing the efficacy and reducing the cost of SIT programs. However, mass rearing, extensive inbreeding, possible bottleneck phenomena and hitch-hiking effects might pose major risks for deterioration and loss of important genetic characteristics of domesticated insect. In the present study, we present a modified procedure to cryopreserve the embryos of the medfly Vienna 8 GSS based on vitrification and used this strain as insect model to assess the impact of the cryopreservation process on the genetic structure of the cryopreserved insects. Forty-eight hours old embryos, incubated at 24°C, were found to be the most suitable developmental stage for cryopreservation treatment for high production of acceptable hatch rate (38%). Our data suggest the absence of any negative impact of the cryopreservation process on egg hatch rate, pupation rates, adult emergence rates and stability of the temperature sensitive lethal (tsl) character on two established cryopreserved lines (flies emerged from cryopreserved embryos), named V8-118 and V8-228. Taken together, our study provides an optimized procedure to cryopreserve the medfly Vienna 8 GSS and documents the absence of any negative impact on the genetic structure and quality of the strain. Benefits and sceneries for utilization of this technology to support operational SIT projects are discussed in this paper. PMID:27537351

Cryopreservation of Embryos of the Mediterranean Fruit Fly Ceratitis capitata Vienna 8 Genetic Sexing Strain.

PubMed

Augustinos, Antonios A; Rajamohan, Arun; Kyritsis, Georgios A; Zacharopoulou, Antigone; Haq, Ihsan Ul; Targovska, Asya; Caceres, Carlos; Bourtzis, Kostas; Abd-Alla, Adly M M

2016-01-01

The Mediterranean fruit fly, Ceratitis capitata, is one of the most serious pests of fruit crops world-wide. During the last decades, area-wide pest management (AW-IPM) approaches with a sterile insect technique (SIT) component have been used to control populations of this pest in an effective and environment-friendly manner. The development of genetic sexing strains (GSS), such as the Vienna 8 strain, has been played a major role in increasing the efficacy and reducing the cost of SIT programs. However, mass rearing, extensive inbreeding, possible bottleneck phenomena and hitch-hiking effects might pose major risks for deterioration and loss of important genetic characteristics of domesticated insect. In the present study, we present a modified procedure to cryopreserve the embryos of the medfly Vienna 8 GSS based on vitrification and used this strain as insect model to assess the impact of the cryopreservation process on the genetic structure of the cryopreserved insects. Forty-eight hours old embryos, incubated at 24°C, were found to be the most suitable developmental stage for cryopreservation treatment for high production of acceptable hatch rate (38%). Our data suggest the absence of any negative impact of the cryopreservation process on egg hatch rate, pupation rates, adult emergence rates and stability of the temperature sensitive lethal (tsl) character on two established cryopreserved lines (flies emerged from cryopreserved embryos), named V8-118 and V8-228. Taken together, our study provides an optimized procedure to cryopreserve the medfly Vienna 8 GSS and documents the absence of any negative impact on the genetic structure and quality of the strain. Benefits and sceneries for utilization of this technology to support operational SIT projects are discussed in this paper.

Direct determination of graphene quantum dots based on terbium-sensitized luminescence.

PubMed

Llorent-Martínez, Eulogio J; Molina-García, Lucía; Durán, Gema M; Ruiz-Medina, Antonio; Ríos, Ángel

2018-06-05

Graphene quantum dots (GQD) were determined in water samples using terbium-sensitized luminescence (TSL). Terbium ions complex with GQD due to the carboxylic groups that are usually present in these nanomaterials, increasing the luminescence signal of terbium. In Tb(III)-GQD complexes, GQD absorb energy at their characteristic excitation wavelength and transfer it to terbium ion, which emits at its particular emission wavelength. The analytical signal, measured at λ exc =257nm and λ em =545nm, increases proportionally to GQD concentration between 50 and 500μgL -1 . Under optimum conditions, the proposed method presents a detection limit of 15μgL -1 and is selective to GQD in the presence of other nanomaterials of similar size. As GQD are highly water-soluble, they are potential contaminants in environmental or drinking waters water samples, and hence the method was applied to the analysis of different drinking waters which were the target samples for the application of the developed method. Copyright © 2018 Elsevier B.V. All rights reserved.

Acquisition of a High Resolution Field Emission Scanning Electron Microscope for the Analysis of Returned Samples

NASA Technical Reports Server (NTRS)

Nittler, Larry R.

2003-01-01

This grant furnished funds to purchase a state-of-the-art scanning electron microscope (SEM) to support our analytical facilities for extraterrestrial samples. After evaluating several instruments, we purchased a JEOL 6500F thermal field emission SEM with the following analytical accessories: EDAX energy-dispersive x-ray analysis system with fully automated control of instrument and sample stage; EDAX LEXS wavelength-dispersive x-ray spectrometer for high sensitivity light-element analysis; EDAX/TSL electron backscatter diffraction (EBSD) system with software for phase identification and crystal orientation mapping; Robinson backscatter electron detector; and an in situ micro-manipulator (Kleindiek). The total price was $550,000 (with $150,000 of the purchase supported by Carnegie institution matching funds). The microscope was delivered in October 2002, and most of the analytical accessories were installed by January 2003. With the exception of the wavelength spectrometer (which has been undergoing design changes) everything is working well and the SEM is in routine use in our laboratory.

Surfactant-enhanced anaerobic acidogenesis of Canna indica L. by rumen cultures.

PubMed

Yue, Zheng-Bo; Yu, Han-Qing; Hu, Zhen-Hu; Harada, Hideki; Li, Yu-You

2008-06-01

Polyoxyethylene sorbitan monoolate (Tween 80) was used to enhance the anaerobic acidogenesis of Canna indica L. (canna) by rumen culture in this study. Dose of Tween 80 at 1 ml/l enhanced the volatile fatty acids (VFA) production from the acidogenesis of canna compared to the control. However, Tween 80 at higher dosages than 5 ml/l inhibited the rumen microbial activity and reduced the VFA yield. Response surface methodology was successfully used to optimize the VFA yield. A maximum of VFA yield of 0.147 g/g total solids (TS) added was obtained at canna and Tween 80 concentrations of 6.3g TS/l and 2.0 ml/l, respectively. Dosage of Tween 80 at 1-3.75 ml/l reduced the unproductive adsorption of microbes or enzymes on the lignin part in canna and increased microbial activity. A high VFA production was achieved from canna presoaked with Tween 80, suggesting that the structure of canna was disrupted by Tween 80.

Direct determination of graphene quantum dots based on terbium-sensitized luminescence

NASA Astrophysics Data System (ADS)

Llorent-Martínez, Eulogio J.; Molina-García, Lucía; Durán, Gema M.; Ruiz-Medina, Antonio; Ríos, Ángel

2018-06-01

Graphene quantum dots (GQD) were determined in water samples using terbium-sensitized luminescence (TSL). Terbium ions complex with GQD due to the carboxylic groups that are usually present in these nanomaterials, increasing the luminescence signal of terbium. In Tb(III)-GQD complexes, GQD absorb energy at their characteristic excitation wavelength and transfer it to terbium ion, which emits at its particular emission wavelength. The analytical signal, measured at λexc = 257 nm and λem = 545 nm, increases proportionally to GQD concentration between 50 and 500 μg L-1. Under optimum conditions, the proposed method presents a detection limit of 15 μg L-1 and is selective to GQD in the presence of other nanomaterials of similar size. As GQD are highly water-soluble, they are potential contaminants in environmental or drinking waters water samples, and hence the method was applied to the analysis of different drinking waters which were the target samples for the application of the developed method.

Floods, fish, and people: Connecting biogeochemical fluxes to aquatic ecosystem functions and people (Invited)

NASA Astrophysics Data System (ADS)

Holtgrieve, G. W.; Arias, M. E.; Chheng, P.

2013-12-01

The Lower Mekong River basin, including Tonle Sap Lake (TSL), is the largest inland fishery in the world and a dominant source of protein and income for much of Southeast Asia. Maintaining ecosystem productivity in the face of large-scale environmental change from hydroelectric dams and climate change is critical for economic and social well-being in the region. Yet, we currently lack the most basic understanding of how hydrologic variation relates to fisheries production, nutritional quality, and ultimately livelihoods of people. We will describe past, present, and future research to establish mechanistic connections between the hydrology, ecology, and sustainability of the Mekong ecosystem. Past research includes application of a state-space oxygen mass balance model and continuous dissolved oxygen measurements from four locations to provide the first estimates of gross primary productivity (GPP) and ecosystem respiration (ER) for the Tonle Sap. GPP averaged 4.1 × 2.3 g O2 m-3 d-1 with minimal differences among sites, while ER averaged 24.9 × 20.0 g O2 m-3 d-1, but had greater than six-fold variation among sites. Using our measurements of GPP, we calibrated a hydrodynamic-productivity model and predicted aquatic net primary production of 2.0 × 0.2 g C m-2 d-1 (2.4 × 0.2 million tonnes C y-1). Present research is using stable isotope and fatty acid methyl ester biomarkers to investigate basal carbon sources to the fishery, focusing specifically on the role of biogenic methane oxidation in supporting the food web. Individuals a wide variety of taxa had tissue carbon isotope values (δ13C) ranging from -36 to -57 per mil. These extremely depleted values are best explained by utilization of biogenic methane by methane oxidizing bacteria (MOB) and subsequent grazing of these bacterial by benthic insects and ultimately fishes. The presence of MOB in the food web was confirmed by identifying 16:1ω8 and 18:1ω8 FAME biomarkers specific to these bacteria in fish tissues. Finally, we will discuss future research to understand how hydrology and fishing practices interact to structure fish populations and, in turn, the amount and quality of nutrition available to people. Alterations to the sediment and oxygen dynamics of the TSL, as a result of hydroelectric dams, has the potential to significantly alter fish population dynamics and influence the role methane plays as a carbon source to this economically and socially important fishery.

[Effect of NaOH-treatment on dry-thermophilic anaerobic digestion of Spartina alterniflora].

PubMed

Chen, Guang-Yin; Zheng, Zheng; Chang, Zhi-Zhou; Ye, Xiao-Mei; Luo, Yan

2011-07-01

In order to improve the biotransformation rate of lignocellulosic materials, sodium hydroxide (NaOH) was widely used to pretreat lignocellulosic materials. Effect of NaOH-treatment on dry-thermophilic anaerobic digestion of Spartina alternflora was studied by batch model under the temperature of 55 degrees C +/- 1 degrees C, at the initial total solid loading (TSL) of 20%. The results indicated that biogas production was inhibited by NaOH-treatment and improved by NaOH-treatment with water washed. The cumulative biogas yield of control (CK), NaOH-treated and NaOH-treated with water washed (NaOH + water) were 268.35 mL/g, 205.76 mL/g and 299.97 mL/g, respectively. The methane content of CK and NaOH + water treatments kept stable while fluctuation of NaOH-treated treatment during anaerobic digestion process was observed. Compared with CK and NaOH + water treatments, methane content of NaOH-treated treatment was improved by 5.30%. The content of hemi-cellulose and cellulose of S. alternifora decreased while content of lignin of S. alterniflora increased after 51-day anaerobic digestion. The crystallinity of cellulose of S. alterniflora increased after NaOH-treatment which was consistent to the result of FTIR. The lignocellulosic structure was destroyed and the biodegradability of S. alterniflora was increased by NaOH pretreatment. However, the amount of Na+ was taken into the anaerobic system, besides the high Na+ content in the plant itself which inhibited the anaerobic microorganisms. Therefore, NaOH-treatment is considered to be unsuitable for the anaerobic digestion of S. alterniflora.

[Automated procedures for microscopic analyses of blood smears: medical testing a MECOS-Ts2 complex].

PubMed

Pliasunova, S A; Balugian, R Sh; Khmel'nitskiĭ, K E; Medovyĭ, V S; Parpara, A A; Piatnitskiĭ, A M; Sokolinskiĭ, B Z; Dem'ianov, V L; Nikolaenko, D S

2006-10-01

The paper presents the results of medical tests of a group of computer-aided procedures for microscopic analysis by means of a MECOS-Ts2 complex (ZAO "MECOS", Russia), which have been conducted at the Republican Children's Clinical Hospital, the Research Institute of Emergency Pediatric Surgery and Traumatology, and Moscow City Clinical Hospital No. 23. Computer-aided procedures for calculating the differential count and for analyzing the morphology of red blood cells were tested on blood smears from a total of 443 patients and donors, computer-aided calculation of the count of reticulocytes was tested on 318 smears. The tests were carried out under the US standard NCCLS-H20A. Manual microscopy (443 smears) and flow blood analysis on a Coulter GEN*S (125 smears) were used as reference methods. The quality of collection of samples and laboriousness were additionally assessed. The certified MECOS-Ts2 subsystems were additionally used as reference tools. The tests indicated the advantage of computer-aided MECOS-Tsl2 complex microscopy over manual microscopy.

Explosive Contamination from Substrate Surfaces: Differences and Similarities in Contamination Techniques using RDX and C-4

DOE Office of Scientific and Technical Information (OSTI.GOV)

C.J. Miller; T.S. Yoder

The amount of time that an explosive is present on the surface of a material is dependent upon the original amount of explosive on the surface, temperature, humidity, rain, etc. This laboratory study focused on looking at similarities and differences in three different surface contamination techniques that are used when performance testing explosive trace detection equipment in an attempt to determine how effective the techniques are at replicating actual field samples. The three techniques used were dry transfer deposition of solutions using the Transportation Security Laboratory (TSL) patented dry transfer techniques (US patent 6470730), direct deposition of explosive standards, andmore » fingerprinting of actual explosives. Explosives were deposited on the surface of one of five substrates using one of the three different deposition techniques. The process was repeated for each surface type using each contamination technique. The surface types used were: 50% cotton/50% polyester as found in T-shirts, 100% cotton with a smooth surface such as that found in a cotton dress shirt, 100% cotton on a rough surface such as that found on canvas or denim, suede leather such as might be found on jackets, purses, or shoes, and metal obtained from a car hood at a junk yard. The samples were not pre-cleaned prior to testing and contained sizing agents, and in the case of the metal, oil and dirt. The substrates were photographed using a Zeiss Discover V12 stereoscope with Axiocam ICc1 3 megapixel digital camera to determine the difference in the crystalline structure and surface contamination in an attempt to determine differences and similarities associated with current contamination techniques.« less

Luminescence quenching and scintillation response in the Ce3+ doped GdxY3-xAl5O12 (x = 0.75, 1, 1.25, 1.5, 1.75, 2) single crystals

NASA Astrophysics Data System (ADS)

Bartosiewicz, K.; Babin, V.; Kamada, K.; Yoshikawa, A.; Mares, J. A.; Beitlerova, A.; Nikl, M.

2017-01-01

The luminescence and scintillation properties of the gadolinium yttrium aluminium garnets, (Gd,Y)3Al5O12 doped with Ce3+ are investigated as a function of the Gd/Y ratio with the aim of an improved understanding of the luminescence quenching, energy transfer and phase stability in these materials. An increase of both crystal field strength and instability of the garnet phase with increasing content of Gd3+ is observed. The instability of the garnet phase results in an appearance of the perovskite phase inclusions incorporated into the garnet phase. The luminescence features of Ce3+ in the perovskite phase inclusions and in the main garnet phase are studied separately. The thermal quenching of the 5 d → 4f emission of Ce3+ in the latter phase is determined by temperature dependence of the photoluminescence decay time. The results show that the onset of the thermal quenching is moved to lower temperatures with increasing gadolinium content. The measurements of temperature dependence of delayed radiative recombination do not reveal a clear evidence that the thermal quenching is caused by thermally induced ionization of the Ce3+ 5d1 excited state. Therefore, the main mechanism responsible for the luminescence quenching is due to the non-radiative relaxation from 5d1 excited state to 4f ground state of Ce3+. The energy transfer processes between Gd3+ and Ce3+ as well as between perovskite and garnet phases are evidenced by the photoluminescence excitation and emission spectra as well as decay kinetic measurements. Thermally stimulated luminescence (TSL) studies in the temperature range 77-497 K and scintillation decays under γ excitation complete the material characterization.

D/H in Water Evolved from Martian Rocks in Gale Crater

NASA Astrophysics Data System (ADS)

Mahaffy, P. R.; Franz, H. B.; Atreya, S. K.; Webster, C. R.

2017-12-01

The Sample Analysis at Mars (SAM) instrument suite with its Quadrupole Mass Spectrometer (QMS) and Tunable Laser Spectrometer (TSL) measures isotopes such as δ34S in SO2 [1], δ37Cl in HCl [2], δ15N in N2 or NO [3], δ13C in CH4 [4], δ13C and δ18O in CO2 [5-6], δD in H2O [7], and a variety of noble gas isotopes [8-9]. Fractionation of isotopes of H, C, O, N, Ar, and Xe indicates a substantial loss of atmosphere to space. For xenon this may have occurred early in the history of Mars by hydrodynamic escape [10] or spread over time for C, O, N, and Ar [11]. Nevertheless, the detailed history of atmospheric loss and the predictions of the climate when the Gale crater was a lake are still not well constrained. Isotopes from light elements that are presently measured in the atmosphere but that were also locked into minerals in rocks more than 3 billion years ago are of particular interest as they may provide additional constraints on the history of atmospheric loss. These include 15N/14N presently measured in atmospheric N2 [3] but also in nitrogen released from ancient nitrates as NO [12] and D/H in atmospheric water [13] and in water or hydroxyl locked into minerals and released in the SAM evolved gas analysis (EGA) experiments [7]. D/H in water can be measured by both the TSL and the QMS. Typically the D/H decreases over the course of the EGA temperature ramp, since gas that has exchanged with the current atmosphere is released at lower temperatures. Less easily exchanged gas reflecting the D/H ratio in the water of formation of a mineral, such as that from the dehydroxylation of a phylosillicate, is released at higher temperatures. We will examine some of the D/H measurements made on drilled and powdered rocks and the trends in the variation of the D/H ratio with release temperature. We will compare these ratios with the D/H in atmospheric water and discuss possible consequences for loss of D/H over time. References: [1] Franz et al., in press. [2] Farley et al. (2016) EPSL 438. [3] Wong et al. (2013) GRL 40. [4] Webster et al. (2011) PSS 59. [5] Mahaffy et al. (2013) Science 341. [6] Webster et al. (2013) Science 341. [7] Mahaffy et al. (2015) Science 347. [8] Atreya et al. (2013) GRL 40. [9] Conrad et al. (2016) EPSL 454. [10] Pepin et al. (2006) EPSL 252. [11] Jakosky et al. (1994) Icarus 111. [12] Stern, this meeting. [13] Villaneuva et al. (2015) Science 348.

Text generation from Taiwanese Sign Language using a PST-based language model for augmentative communication.

PubMed

Wu, Chung-Hsien; Chiu, Yu-Hsien; Guo, Chi-Shiang

2004-12-01

This paper proposes a novel approach to the generation of Chinese sentences from ill-formed Taiwanese Sign Language (TSL) for people with hearing impairments. First, a sign icon-based virtual keyboard is constructed to provide a visualized interface to retrieve sign icons from a sign database. A proposed language model (LM), based on a predictive sentence template (PST) tree, integrates a statistical variable n-gram LM and linguistic constraints to deal with the translation problem from ill-formed sign sequences to grammatical written sentences. The PST tree trained by a corpus collected from the deaf schools was used to model the correspondence between signed and written Chinese. In addition, a set of phrase formation rules, based on trigger pair category, was derived for sentence pattern expansion. These approaches improved the efficiency of text generation and the accuracy of word prediction and, therefore, improved the input rate. For the assessment of practical communication aids, a reading-comprehension training program with ten profoundly deaf students was undertaken in a deaf school in Tainan, Taiwan. Evaluation results show that the literacy aptitude test and subjective satisfactory level are significantly improved.

Measuring Light-ion Production and Fission Cross Sections Normalised to H(n,p) Scattering at the Upcoming NFS Facility

NASA Astrophysics Data System (ADS)

Jansson, K.; Gustavsson, C.; Pomp, S.; Prokofiev, A. V.; Scian, G.; Tarrío, D.

2014-05-01

The Medley detector setup is planned to be moved to and used at the new neutron facility NFS where measurements of light-ion production and fission cross-sections are planned at 1-40 MeV. Medley has eight detector telescopes providing ΔE-ΔE-E data, each consisting of two silicon detectors and a CsI(Tl) detector at the back. The telescope setup can be rotated and arranged to cover any angle. Medley has previously been used in many measurements at The Svedberg Laboratory (TSL) in Uppsala mainly with a quasi-mono-energetic neutron beam at 96 and 175 MeV. To be able to do measurements at NFS, which will have a white neutron beam, Medley needs to detect the reaction products with a high timing resolution providing the ToF of the primary neutron. In this paper we discuss the design of the Medley upgrade along with simulations of the setup. We explore the use of Parallel Plate Avalanche Counters (PPACs) which work very well for detecting fission fragments but require more consideration for detecting deeply penetrating particles.

Lessons learned in the execution of advanced x-ray material discrimination (Conference Presentation)

NASA Astrophysics Data System (ADS)

Young, Sharene

2017-05-01

Advanced X-ray Material Discrimination (AXMD) or BAA 13-05 was a broad agency announcement which was initiated in order to develop solutions to the following problem. The emergence of improvised explosive threats and their use by terrorists has placed many challenges on the aviation security screening layers. EDS and AT X-ray equipment have been presented with considerable challenges in developing a broad detection capability for improvised explosive threats during security screening of checked bags and carry-on items. Technologies are needed that increase the measurement or mathematical discrimination between improvised explosive threats and stream-of-commerce clutter in checked baggage and carry-on items. Conventional EDS utilizes two basic discriminating signatures: effective atomic number and density of screened objects. R and D is needed to identify additional discriminating signatures between improvised explosive threats and stream-of commerce clutter to improve detection capability with reduced false alarm rates. DHS S and T EXD along with stakeholders at the TSA, TSL, and the UK Home Office have been successful in funding efforts to address and potentially provide operational solutions which can be deployed as part of the Next Generation of X-ray Technologies.

Accumulation of radiation defects and products of radiolysis in lithium orthosilicate pebbles with silicon dioxide additions under action of high absorbed doses and high temperature in air and inert atmosphere

NASA Astrophysics Data System (ADS)

Zarins, A.; Supe, A.; Kizane, G.; Knitter, R.; Baumane, L.

2012-10-01

One of the technological problems of a fusion reactor is the change in composition and structure of ceramic breeders (Li4SiO4 or Li2TiO3 pebbles) during long-term operation. In this study changes in the composition and microstructure of Li4SiO4 pebbles with 2.5 wt% silicon dioxide additions, fabricated by a melt-spraying process, were investigated after fast electron irradiation (E = 5 MeV, dose rate up to 88 MGy h-1) with high absorbed dose from 1.3 to 10.6 GGy at high temperature (543-573 K) in air and argon atmosphere. Three types of pebbles with different diameters and grain sizes were investigated. Products of radiolysis were studied by means of FTIR and XRD. TSL and ESR spectroscopy were used to detect radiation defects. SEM was used to investigate structure of pebbles. Experiments showed that Li4SiO4 pebbles with a diameter of 500 μm had similar radiation stability as pebbles with diameter <50 μm which were annealed at 1173 K for 128 h in argon and air atmosphere. As well as determined that lithium orthosilicate pebbles with size 500 (1243 K 168 h) and <50 μm (1173 K 128 h) have a higher radiation stability in air and argon atmosphere than pebbles with size <50 μm (1073 K 1 h). Degree of decomposition α10.56 of the lithium orthosilicate pebbles at an absorbed dose of 10.56 GGy in air atmosphere is 1.5% and 0.15% at irradiation in dry argon. It has been suggested that changes of radiation stability of lithium orthosilicate pebbles in air atmosphere comparing with irradiated pebbles in argon atmosphere is effect of chemical reaction of lithium orthosilicate surface with air containing - H2O and CO2 in irradiation process. As well as it has been suggested that silicon dioxide - lithium metasilicate admixtures do not affect formation mechanism of radiation defect and products of radiolysis in lithium orthosilicate pebbles.

Integrated geographic information systems (IGIS) analysis and definition of the tectonic framework of northern Mexico

NASA Astrophysics Data System (ADS)

Martinez Pina, Carlos Manuel

Crustal rupture structures reactivated in the course of the tectonic history of northern Mexico are the surface expressions of planes of weakness, in the form of simple or composite rectilinear features or slightly curved, defined as lineaments. Unless otherwise defined as strike-slip faults, lineaments are part of parallel and sub-parallel oblique convergent or oblique divergent tectonic zones cross cutting the Sierra Madre Occidental and northern Mexico, in a NW trend. These shear zones are the response to the oblique subduction of the Farallon plate beneath North America. Kinematic analysis of five selected sites in northern Mexico, three basins and two compressional shear zones, proved possible a combination of shear mechanism diagram and models from analogue materials, with satellite imagery and geographic information systems, as an aid to define strike-slip fault motion. This was done using a reverse engineering process by comparing geometries. One of the sites assessed, involving the Parras Basin, Coahuila Block (CB), San Marcos fault, a postulated PBF-1 fault, allowed for palinpastic reconstruction of the CB that corroborated the results of the vector motion defined, in addition to an extension of ˜25% in a northwest southeast direction. A GIS-based compilation and georeferenced regional structural studies by several researchers were used as ground control areas (GCA); their interpolation and interpretation, resulted in a tectonic framework map of northern Mexico. In addition, shaded relief models overlaid by the lineaments / fault layer allowed structural analyses of basins related to these major structures. Two important results were obtained from this study: the Tepehuanes-San Luis-fault (TSL) and the Guadalupe fault, named herein, displaces the Villa de Reyes graben, and the Aguascalientes graben, respectively, to the SE, confirming their left lateral vector motion; afterwards TSL was displaced south by the right lateral strike slip Taxco-San Miguel de Allende fault. The second result refers to the hypothesis that the Mesa Central was brought to its present location by a subduction zone located to the north. This subduction zone coincides with several researchers who postulated the idea. The compressional zones refer to segments of the Sinforosa and a postulated Aquinquari fault located in the stratotectonic Guerrero Terrane regarded as a highly mineralized zone. Negative anomalies near -200 milligals are strongly suggestive of a cratonic block identified in western Chihuahua, it being named the Western Chihuahua Cratonic Block (WCCB). In the southwestern portion of the North American craton the age provinces are well documented, but the block versus mobile belt idea has not been put forth or emphasized. The present study combines data of several types, sedimentological, structural, igneous geochemistry, and geochronologic data to evaluate this behavior in SW NA, and the proposed block is tested against these data. The presence of the WCCB is supported by a wide variety of data. Basins, troughs, aulacogens, bimodal volcanism, and other rift and rift shoulder features, characterize the spatially constrained mobile belts. Mobile belts surrounding the WCCB contain geologic records of the events going back to 1.4 Ga, with different aspects being dominant over geologic time. Mobile belts will participate in compression,(subduction), extension (rifting), and transform (lateral) faulting. The WCCB may have been derived from closely, adjacent, North American craton by mobile belt action. This study has shown that integration of data is essential, because allows detection of differences in hypotheses for the same event in the same area. This integration capability is what makes integrated geographic information systems a powerful tool, not only for their synergy, but because they can be combined with specific techniques that provide data before going to conduct fieldwork. Whether the issue of defining the tectonic framework of northern Mexico can be resolved or not, depends on the viability of integrating volumes of data from research, hypotheses, or maps, and put together under the same geographic frame.

CFD Modeling of Swirl and Nonswirl Gas Injections into Liquid Baths Using Top Submerged Lances

NASA Astrophysics Data System (ADS)

Huda, Nazmul; Naser, J.; Brooks, G.; Reuter, M. A.; Matusewicz, R. W.

2010-02-01

Fluid flow phenomena in a cylindrical bath stirred by a top submerged lance (TSL) gas injection was investigated by using the computational fluid dynamic (CFD) modeling technique for an isothermal air-water system. The multiphase flow simulation, based on the Euler-Euler approach, elucidated the effect of swirl and nonswirl flow inside the bath. The effects of the lance submergence level and the air flow rate also were investigated. The simulation results for the velocity fields and the generation of turbulence in the bath were validated against existing experimental data from the previous water model experimental study by Morsi et al.[1] The model was extended to measure the degree of the splash generation for different liquid densities at certain heights above the free surface. The simulation results showed that the two-thirds lance submergence level provided better mixing and high liquid velocities for the generation of turbulence inside the water bath. However, it is also responsible for generating more splashes in the bath compared with the one-third lance submergence level. An approach generally used by heating, ventilation, and air conditioning (HVAC) system simulations was applied to predict the convective mixing phenomena. The simulation results for the air-water system showed that mean convective mixing for swirl flow is more than twice than that of nonswirl in close proximity to the lance. A semiempirical equation was proposed from the results of the present simulation to measure the vertical penetration distance of the air jet injected through the annulus of the lance in the cylindrical vessel of the model, which can be expressed as L_{va} = 0.275( {do - di } )Frm^{0.4745} . More work still needs to be done to predict the detail process kinetics in a real furnace by considering nonisothermal high-temperature systems with chemical reactions.

New evaluation of thermal neutron scattering libraries for light and heavy water

NASA Astrophysics Data System (ADS)

Marquez Damian, Jose Ignacio; Granada, Jose Rolando; Cantargi, Florencia; Roubtsov, Danila

2017-09-01

In order to improve the design and safety of thermal nuclear reactors and for verification of criticality safety conditions on systems with significant amount of fissile materials and water, it is necessary to perform high-precision neutron transport calculations and estimate uncertainties of the results. These calculations are based on neutron interaction data distributed in evaluated nuclear data libraries. To improve the evaluations of thermal scattering sub-libraries, we developed a set of thermal neutron scattering cross sections (scattering kernels) for hydrogen bound in light water, and deuterium and oxygen bound in heavy water, in the ENDF-6 format from room temperature up to the critical temperatures of molecular liquids. The new evaluations were generated and processable with NJOY99 and also with NJOY-2012 with minor modifications (updates), and with the new version of NJOY-2016. The new TSL libraries are based on molecular dynamics simulations with GROMACS and recent experimental data, and result in an improvement of the calculation of single neutron scattering quantities. In this work, we discuss the importance of taking into account self-diffusion in liquids to accurately describe the neutron scattering at low neutron energies (quasi-elastic peak problem). To improve modeling of heavy water, it is important to take into account temperature-dependent static structure factors and apply Sköld approximation to the coherent inelastic components of the scattering matrix. The usage of the new set of scattering matrices and cross-sections improves the calculation of thermal critical systems moderated and/or reflected with light/heavy water obtained from the International Criticality Safety Benchmark Evaluation Project (ICSBEP) handbook. For example, the use of the new thermal scattering library for heavy water, combined with the ROSFOND-2010 evaluation of the cross sections for deuterium, results in an improvement of the C/E ratio in 48 out of 65 international benchmark cases calculated with the Monte Carlo code MCNP5, in comparison with the existing library based on the ENDF/B-VII.0 evaluation.

DNA sequence analysis of the composite plasmid pTC conferring virulence and antimicrobial resistance for porcine enterotoxigenic Escherichia coli.

PubMed

Fekete, Péter Z; Brzuszkiewicz, Elzbieta; Blum-Oehler, Gabriele; Olasz, Ferenc; Szabó, Mónika; Gottschalk, Gerhard; Hacker, Jörg; Nagy, Béla

2012-01-01

In this study the plasmid pTC, a 90 kb self-conjugative virulence plasmid of the porcine enterotoxigenic Escherichia coli (ETEC) strain EC2173 encoding the STa and STb heat-stable enterotoxins and tetracycline resistance, has been sequenced in two steps. As a result we identified five main distinct regions of pTC: (i) the maintenance region responsible for the extreme stability of the plasmid, (ii) the TSL (toxin-specific locus comprising the estA and estB genes) which is unique and characteristic for pTC, (iii) a Tn10 transposon, encoding tetracycline resistance, (iv) the tra (plasmid transfer) region, and (v) the colE1-like origin of replication. It is concluded that pTC is a self-transmissible composite plasmid harbouring antibiotic resistance and virulence genes. pTC belongs to a group of large conjugative E. coli plasmids represented by NR1 with a widespread tra backbone which might have evolved from a common ancestor. This is the first report of a completely sequenced animal ETEC virulence plasmid containing an antimicrobial resistance locus, thereby representing a selection advantage for spread of pathogenicity in the presence of antimicrobials leading to increased disease potential. Copyright © 2011. Published by Elsevier GmbH.

Effect of initial total solids concentration on volatile fatty acid production from food waste during anaerobic acidification.

PubMed

Wang, Quan; Jiang, Jianguo; Zhang, Yujing; Li, Kaimin

2015-01-01

The effect of initial total solids (TS) concentration on volatile fatty acid (VFAs) production from food waste under mesophilic conditions (35 °C) was determined. VFAs concentration and composition, biogas production, soluble chemical oxygen demand concentration, TS and volatile solids (VS) reduction, and ammonia nitrogen [Formula: see text] release were investigated. The VFAs concentrations were 26.10, 39.68, 59.58, and 62.64 g COD/L at TS contents of 40, 70, 100, and 130 g/L, respectively. While the VFAs' yields ranged from 0.467 to 0.799 g COD/g VSfed, decreased as initial TS increased. The percentage of propionate was not affected by TS concentration, accounting for 30.19-34.86% of the total VFAs, while a higher percentage of butyrate and lower percentage of acetate was achieved at a higher TS concentration. Biogas included mainly hydrogen and carbon dioxide and the maximum hydrogen yield of 148.9 ml/g VSfed was obtained at 130 g TS/L. [Formula: see text] concentration, TS and VS reductions increased as initial TS increased. Considering the above variables, we conclude that initial TS of 100 g/L shall be the most appropriate to VFAs production.

Gee Fu: a sequence version and web-services database tool for genomic assembly, genome feature and NGS data.

PubMed

Ramirez-Gonzalez, Ricardo; Caccamo, Mario; MacLean, Daniel

2011-10-01

Scientists now use high-throughput sequencing technologies and short-read assembly methods to create draft genome assemblies in just days. Tools and pipelines like the assembler, and the workflow management environments make it easy for a non-specialist to implement complicated pipelines to produce genome assemblies and annotations very quickly. Such accessibility results in a proliferation of assemblies and associated files, often for many organisms. These assemblies get used as a working reference by lots of different workers, from a bioinformatician doing gene prediction or a bench scientist designing primers for PCR. Here we describe Gee Fu, a database tool for genomic assembly and feature data, including next-generation sequence alignments. Gee Fu is an instance of a Ruby-On-Rails web application on a feature database that provides web and console interfaces for input, visualization of feature data via AnnoJ, access to data through a web-service interface, an API for direct data access by Ruby scripts and access to feature data stored in BAM files. Gee Fu provides a platform for storing and sharing different versions of an assembly and associated features that can be accessed and updated by bench biologists and bioinformaticians in ways that are easy and useful for each. http://tinyurl.com/geefu dan.maclean@tsl.ac.uk.

Exercise intensity and gender difference of 3 different salsa dancing conditions.

PubMed

Emerenziani, G P; Guidetti, L; Gallotta, M C; Franciosi, E; Buzzachera, C F; Baldari, C

2013-04-01

The aims of this study were to estimate the difference in exercise intensity (METs), energy cost (EE) and gender difference between a typical salsa lesson (TSL), rueda de casino lesson (RCL), and salsa dancing at a night club (SDN). Subjects performed 1 pre-testing session and 3 testing conditions. During the pre-testing session height, weight and V˙O2max were assessed. During the testing conditions all subjects performed 3 different kinds of salsa dance. Heart rate was assessed during each dance condition. The exercise intensity of the 3 salsa dancing conditions was moderate ranging from 3.9 to 5.5 METs. A significant difference between genders for HRpeak (P=0.01), max%HRR (P=0.006) and mean EE (P=0.02) were observed. Significant gender×condition interactions for HRpeak (P=0.03), mean %HRR (P=0.02), mean METs (P=0.02) and mean EE (P=0.02) were found. In addition, a significant main effect for each condition was found in all variables (P<0.01). Our results showed that the exercise intensities of all 3 salsa dancing conditions were moderate. Findings showed some significant differences in exercise intensity between males and females and within conditions. Salsa dancing could be useful in achieving a significant training effect in people who have a low level of fitness. © Georg Thieme Verlag KG Stuttgart · New York.

Optimized efficient liver T1ρ mapping using limited spin lock times

NASA Astrophysics Data System (ADS)

Yuan, Jing; Zhao, Feng; Griffith, James F.; Chan, Queenie; Wang, Yi-Xiang J.

2012-03-01

T1ρ relaxation has recently been found to be sensitive to liver fibrosis and has potential to be used for early detection of liver fibrosis and grading. Liver T1ρ imaging and accurate mapping are challenging because of the long scan time, respiration motion and high specific absorption rate. Reduction and optimization of spin lock times (TSLs) are an efficient way to reduce scan time and radiofrequency energy deposition of T1ρ imaging, but maintain the near-optimal precision of T1ρ mapping. This work analyzes the precision in T1ρ estimation with limited, in particular two, spin lock times, and explores the feasibility of using two specific operator-selected TSLs for efficient and accurate liver T1ρ mapping. Two optimized TSLs were derived by theoretical analysis and numerical simulations first, and tested experimentally by in vivo rat liver T1ρ imaging at 3 T. The simulation showed that the TSLs of 1 and 50 ms gave optimal T1ρ estimation in a range of 10-100 ms. In the experiment, no significant statistical difference was found between the T1ρ maps generated using the optimized two-TSL combination and the maps generated using the six TSLs of [1, 10, 20, 30, 40, 50] ms according to one-way ANOVA analysis (p = 0.1364 for liver and p = 0.8708 for muscle).

Exercise Thermoregulation Following 13 Days of Bed Rest

NASA Technical Reports Server (NTRS)

Lee, Stuart M. C.; Williams, W. Jon; Schneider, Suzanne M.

2001-01-01

This investigation examined two potential mechanisms, altered skin blood flow (SBF) and sweating rate (SR) responses, that may be responsible for an elevated core temperature during exercise after bed rest (BR) and space flight. Seven healthy men (29 +/- 5 yr, 179.6 +/- 7.1 cm, 77.2 +/- 17.0kg; mean +/- SD) underwent 13 days of 6 deg head-down BR. Pre- and post-BR, subjects completed supine submaximal cycle ergometry (20 min at 40% and 20 min at 65% of pre-BR supine VO2pk) in a thermoneutral room (23.4 +/- 0.5 C, 56 +/- 8 %RH) during, heat production (VO2 ; indirect calorimetry), intestinal temperature (T(sub in) ; ingestible pill), SBF (laser Doppler velocimetry), local SR (dew point hygrometry), and total sweat loss (TSL; Delta body weight) were measured. Pre- and post- BR plasma volume (PV) was measured using I-125 dilution. After BR, T(sub in) was elevated at rest (36.99 +/- 0.14 vs. 37.30 +/- 0.06 C; p<_0.05) and at the end of exercise (37.57 +/- 0.13 vs. 37.90 +/- 0.09 C; P less than or equal to 0.05). However, the increase in T(sub in) from rest to the end of exercise was not different after BR (0.59 +/- 0.07 vs. 0.60 +/- 0.07 C). There was no difference in VO2 pre- to post-BR during rest (0.28 +/- 0.04 vs. 0.24 +/- 0.03 1 multiplied by min(exp -1) ) or 40% VO2pk (0.95 +/- 0.08 vs. 0.96 +/- 0.05 1 multiplied by min(exp -1)), but VO2 was significantly less at the end of the 65% VO2pk stage (1.53 +/- 0.09 vs. 1.42 +/- 0.11 1 multiplies by min(exp - 1); p less than or equal to 0.05). The percent change in SBF from rest to end of exercise was less after BR (211 +/- 53 vs. 96 +/- 31%; p less than or equal to 0.05), the threshold for the onset of SBF was greater (37.17 +/- 0.18vs. 37.51 +/- 0.17 C; p less than or equal to 0.05), and the slope of the response tended to be reduced (536 +/- 184 vs. 201 +/- 46 %A PC; p=0.08). TSL was not different after BR (0.42+0.06 vs. 0.44 +/- 0.08 kg), but the T in threshold at the onset of sweating was delayed significantly (37.06 +/- 0.1 1 vs. 37.34 +/- 0.06 C; p less than or equal to 0.05). However, the slope of SR was not changed after BR (3.45 +/- 1.22 vs. 2.58 +/- 0.71 mg multiplied by min(exp -1) multiplied by cm sq). PV was decreased by 11% after BR (3,259 +/- 177 vs. 2,894 +/- 138 ml; p less than or equal to 0.05). These results suggest that exercise SBF and SR responses after BR are altered, and heat production is unchanged or reduced, consistent with observations following space flight. The higher resting T(sub in) with a proportional increase in T(sub in) during exercise and delayed onset of SBF and SR suggest a centrally-mediated elevation in the thermoregulatory set point during microgravity exposure.

Investigating extreme flood response to Holocene palaeoclimate in the Chinese monsoonal zone: A palaeoflood case study from the Hanjiang River

NASA Astrophysics Data System (ADS)

Guo, Yongqiang; Huang, Chun Chang; Pang, Jiangli; Zha, Xiaochun; Zhou, Yali; Wang, Longsheng; Zhang, Yuzhu; Hu, Guiming

2015-06-01

Palaeoflood events recorded by slackwater deposits (SWDs) were investigated extensively by sedimentological criteria of palaeohydrology along the upper Hanjiang River valley. Modern flood SWDs were collected for comparison with palaeoflood SWD in the same reaches. Three typical palaeoflood SWDs were observed within Holocene loess-soil blanket on the first river terrace land. The grain size distributions of palaeoflood SWDs are similar to modern flood SWDs, whereas they are different from eolian loess and soil. Palaeoflood SWD lies in three major pedo-stratigraphic boundaries (TS/L0, L0/S0, and S0/Lt) in the Holocene loess-soil profiles. The chronology of three palaeoflood episodes was established by OSL dating and pedo-stratigraphic correlation with the well-dated Holocene loess-soil profiles in the upper Hanjiang River basin. Holocene palaeoflood events were dated to 9500-8500, 3200-2800, and 1800-1700 a B.P., respectively. Palaeoflood discharges were estimated by the palaeoflood model (i.e., slope-area method and step-backwater method). The highest discharges are 51,680-53,950 m3 s- 1 at the 11,500-time scale in the Xunyang reach of the upper Hanjiang River valley. Holocene extraordinary hydroclimatic events in the Hanjiang River often result from abnormal atmospheric circulations from Southwest monsoons in the Chinese monsoonal zone. These results provide a regional expression of extreme flood response to Holocene palaeoclimate to understand the effects of global climatic variations on the river system dynamics.

Near white light emitting ZnAl{sub 2}O{sub 4}:Dy{sup 3+} nanocrystals: Sol–gel synthesis and luminescence studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Mithlesh, E-mail: mithlesh@barc.gov.in; Gupta, Santosh K.; Kadam, R.M.

2016-02-15

Highlights: • ZnAl{sub 2}O{sub 4}:Dy{sup 3+} spinel synthesized using sol–gel method. • Characterized by XRD, SEM and PL spectroscopy. • Investigations of emission, excitation and lifetime properties. • Evaluation of defect centers and trap parameters of the system. • Evaluation of CIE indices of near white light emitting phosphor. - Abstract: ZnAl{sub 2}O{sub 4}:Dy{sup 3+} nanoparticles were synthesized using citrate sol–gel method and characterized systematically using X-ray diffraction, scanning electron microscopy and photoluminescence spectroscopy. Emission spectrum of pure ZnAl{sub 2}O{sub 4} shows intense violet blue emission under ultra violet irradiation. Based on electron paramagnetic resonance (EPR) results; it was attributedmore » to presence of singly ionized oxygen vacancy centres in ZnAl{sub 2}O{sub 4}. On doping Dy{sup 3+} in ZnAl{sub 2}O{sub 4}, complete host–dopant energy transfer does not take place. Local structural investigation and lifetime measurements reveal that dysprosium ion is distributed between both Zn{sup 2+} and Al{sup 3+} sites. Near white light from ZnAl{sub 2}O{sub 4}:Dy{sup 3+} is attributed to combined host and dopant luminescence. The trap parameters such as activation energy (E) and frequency factor (s) for TSL glow peak 165 °C were determined using different heating rate method. Thermally stimulated emission showed the presence of oxygen related defect centre.« less

(Durability of building materials and components)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naus, D.J.

1990-11-27

The traveler participated in the fourth meeting of RILEM 100-TSL, Techniques for Service Life Prediction,'' and The Fifth International Conference on Durability of Building Materials and Components.'' In addition, the traveler met with staff members at Taywood Engineering Ltd., Electricite de France, and AEA Technology. The meeting pertained to performance of concrete materials in nuclear power plant structures, time variation of concrete material properties, methods for evaluating concrete structures, and modeling to predict the effects of degradation factors on concrete materials. As many of the concrete structures in general civil engineering applications as well as nuclear power plant applications inmore » Europe are aging, there is increasing emphasis on assessing the durability of these structures. Information was provided of direct application to the Structural Aging Program which would not have been available without these visits. Of equal, or possibly more importance, was the individual contacts established at the organizations visited. Each organization was extremely interested in both the approach and scope of the Structural Aging Program and requested that they be informed of progress. The initial steps were taken to cooperate with several of these researchers and this should help the Structural Aging Program keep abreast of related European activities. In summary, information obtained during this trip will benefit the ongoing Structural Aging Program by informing Oak Ridge National Laboratory (ORNL) of the extensive European research programs addressing the durability of concrete structures, and also by forming and strengthening acquaintances with counterparts in other countries, thus enhancing the basis for possible international cooperation.« less

The use of digital outcrops to study monogenetic volcanoes: Case study at Croscat volcano (Garrotxa Volcanic Zone, Spain)

NASA Astrophysics Data System (ADS)

Geyer, Adelina; García-Sellés, David; Pedrazzi, Dario; Barde-Cabusson, Stéphanie; Martí, Joan; Muñoz, Josep Anton

2014-05-01

During the last years, it has been demonstrated that the study of outcrops with difficult or completely restricted access can be carried out by means of digital representations of the outcrop surface. Furthermore, the study of digital outcrops may facilitate visualization of the features of interest over the entire outcrop, as long as the digital outcrop can be analysed while navigating in real-time, with optional displays for perspective, scale distortions, and attribute filtering. In particular, Terrestrial Laser Scanning (TSL) instruments using Light Detection And Ranging technology (LIDAR) are capable of capturing topographic details and achieve modelling accuracy within a few centimetres. The data obtained permits the creation of detailed 3-D terrain models of larger coverage and accuracy than conventional methods and with almost complete safety of the operators. Here we show digital outcrops may be useful to perform the description of the internal structure of exposed volcanic edifices. A further advantageous application is the estimate of erosion rates and patterns that may be helpful in terms of hazard assessment or preservation of volcanic landscapes. We use as an example of application the Croscat volcano, a monogenetic edifice of the La Garrotxa volcanic field (Spain), which quarrying jobs have exposed the internal part of the volcano leading to a perfect view of its interior but making difficult the access to the upper parts. The Croscat volcano is additionally one of the most emblematic symbols of the La Garrotxa Volcanic Zone Natural Park being its preservation a main target of the park administration.

New Literacies in Schome Park

NASA Astrophysics Data System (ADS)

Gillen, Julia

In this chapter I deploy a synthesis of methods I term virtual literacy ethnography to investigate the diverse literacy practices of the Schome Park project (SPP). This project worked with teenagers on the first European "closed" (i.e. protected) island in the 3D virtual world Teen Second LifeTM (TSL) as described in the previous chapter. Firstly I introduce an ethnographic perspective on this lengthy, rich project and reflect on my own interpretive approach. Introducing my own focus of interest, the new literacy practices fostered by the environment and in particular activities I judge to be especially creative, I begin to develop the methodology of a "virtual literacy ethnography". I show how the diverse multimodal affordances of the communicative domains are imaginatively exploited by the students, supported by peers and staff in an environment characterised by "fluid leadership". I include some analysis of literacy work around a genre traditionally valued by educators, a dictionary, which I was not involved in at the time. I suggest this is an exemplar literacy practice, creative in itself and illustrative of the methodological possibilities and of course limitations linked with the technologies utilised. Traditional distinctions between "reading" and "writing" become permeable in interesting ways as new creative practices, fostered by the environment of the Schome Park programme, emerged. I offer support for Kress's (2005) claim that changes in writing and reading practices amount to a "revolution in the world of communication." In conclusion, I claim that virtual literacy ethnography, as I have proposed it here, can be fruitful in exploring the complexity and creativity of the students' literacy practices, although more developmental work is needed.

A swirling jet-induced cavitation to increase activated sludge solubilisation and aerobic sludge biodegradability.

PubMed

Mancuso, Giuseppe; Langone, Michela; Andreottola, Gianni

2017-03-01

In this work, a modified swirling jet induced hydrodynamic cavitation (HC) has been used for the pre-treatment of excess sludge. In order to both improve the HC treatment efficiencies and reduce the energy consumption, the effectiveness of the HC reactor on sludge disintegration and on aerobic biodegradability has been investigated at different operating conditions and parameters, such as temperature, inlet pressure, sludge total solid (TS) content and reactor geometry. The inlet pressure was related to the flow velocity and pressure drop. The best results in terms of sludge solubilisation were achieved after 2h of HC treatment, treating a 50.0gTSL -1 and using the three heads Ecowirl system, at 35.0°C and 4.0bar. Chemical and respirometric tests proved that sludge solubilisation and aerobic biodegradability can be efficiently enhanced through HC pre-treatment technique. At the optimum operating conditions, the specific supplied energy has been varied from 3276 to 12,780kJkgTS -1 in the HC treatment, by increasing the treatment time from 2 to 8 h, respectively. Low endogenous decay rates (b H ) were measured on the excess sludge at low specific supplied energy, revealing that only an alteration in floc structure was responsible for the sludge solubilisation. On the contrary, higher b H values were measured at higher specific supplied energy, indicating that the sludge solubilisation was related to a decreasing biomass viability, as consequence of dead cells and/or disrupted cells (cell lysis). Copyright © 2016 Elsevier B.V. All rights reserved.

Functional Capacity and Quality of Life in Patients with Chronic Kidney Disease In Pre-Dialytic Treatment and on Hemodialysis--A Cross sectional study.

PubMed

Fassbinder, Tânia Regina Cavinatto; Winkelmann, Eliane Roseli; Schneider, Juliana; Wendland, Juliana; Oliveira, Olvânia Basso de

2015-01-01

Chronic kidney disease (CKD) infers directly in functional capacity, independence and therefore quality of life (QOL). To compare the physical fitness and quality of life of patients with chronic kidney disease submitted on hemodialysis (G1) and predialysis treatment (G2). A cross-sectional study, 54 patients with CKD, 27 of the G1 group (58.15 ± 10.84 years), 27 of G2 group (62.04 ± 16.56 years). There were cardiovascular risk factors, anthropometric measurements, respiratory muscle strength was measured by the inspiratory pressure (MIP) and expiratory (MEP) maximum measured in the manometer, six-minute walk (TC6'), cardiopulmonary exercise test, sit and stand one minute test (TSL1') and the Short-Form Questionary (SF-36) to assess QOL. The patients presented disease of stage between 2 and 5. It was applied the Kolmogorov-Smirnov normality test and used the t (Student) test or the U (Mann Whitney) test to compare the means of quantitative variables and the chi-square Pearson test and Fisher's exact test for qualitative variables. Pearson's or Spearman's test was used to identify correlations. No statistically significant difference was found between G1 and G2 in VO2peak (p = 0,259) in TC6' (p = 0,433) in the MIPmáx (p = 0,158) and found only in the MEPmáx (p = 0,024) to G1. The scores of the SF-36 in both groups showed a worse health status as evidenced by the low score in scores for QOL. Patients with CKD had reduced functional capacity and QOL, and hemodialysis, statistically, didn't have showed negative repercussions when compared with pre-dialysis patients.

SVGenes: a library for rendering genomic features in scalable vector graphic format.

PubMed

Etherington, Graham J; MacLean, Daniel

2013-08-01

Drawing genomic features in attractive and informative ways is a key task in visualization of genomics data. Scalable Vector Graphics (SVG) format is a modern and flexible open standard that provides advanced features including modular graphic design, advanced web interactivity and animation within a suitable client. SVGs do not suffer from loss of image quality on re-scaling and provide the ability to edit individual elements of a graphic on the whole object level independent of the whole image. These features make SVG a potentially useful format for the preparation of publication quality figures including genomic objects such as genes or sequencing coverage and for web applications that require rich user-interaction with the graphical elements. SVGenes is a Ruby-language library that uses SVG primitives to render typical genomic glyphs through a simple and flexible Ruby interface. The library implements a simple Page object that spaces and contains horizontal Track objects that in turn style, colour and positions features within them. Tracks are the level at which visual information is supplied providing the full styling capability of the SVG standard. Genomic entities like genes, transcripts and histograms are modelled in Glyph objects that are attached to a track and take advantage of SVG primitives to render the genomic features in a track as any of a selection of defined glyphs. The feature model within SVGenes is simple but flexible and not dependent on particular existing gene feature formats meaning graphics for any existing datasets can easily be created without need for conversion. The library is provided as a Ruby Gem from https://rubygems.org/gems/bio-svgenes under the MIT license, and open source code is available at https://github.com/danmaclean/bioruby-svgenes also under the MIT License. dan.maclean@tsl.ac.uk.

Mechanical Twinning and Microstructures in Experimentally Stressed Quartzite

NASA Astrophysics Data System (ADS)

Minor, A.; Sintubin, M.; Wenk, H. R.; Rybacki, E.

2015-12-01

Since Dauphiné twins in quartz have been identified as a stress-related intracrystalline microstructure, several electron backscatter diffraction (EBSD) studies revealed that Dauphiné twins are present in naturally deformed quartz-bearing rocks in a wide range of tectono-metamorphic conditions. EBSD studies on experimentally stressed quartzite showed that crystals with particular crystallographic orientations contain many Dauphiné twin boundaries, while neighboring crystals with different orientations are largely free of twin boundaries. To understand the relationship between stress direction and orientation of Dauphiné twinned quartz crystals, a detailed EBSD study was performed on experimentally stressed quartzite samples and compared with an undeformed reference sample. We stressed 4 cylindrical samples in triaxial compression in a Paterson type gas deformation apparatus at GFZ Potsdam. Experimental conditions were 300MPa confining pressure, 500°C temperature and axial stresses of 145MPa, 250MPa and 460MPa for about 30 hours, resulting in a minor strain <0.04%. EBSD scans were obtained with a Zeiss Evo scanning electron microscope and TSL software at UC Berkeley. The EBSD maps show that Dauphiné twinning is present in the starting material as well as in experimentally stressed samples. Pole figures of the bulk orientation of the reference sample compared with stressed samples show a significant difference regarding the distribution for the r and z directions. The reference sample shows an indistinct maximum for r and z, whereas the stressed samples show a maximum for r poles and a minimum for z poles in the axial stress direction. EBSD scans of the reference and stressed samples were further analyzed manually to identify the orientations of single grains, which are free of twin boundaries and those, which contain twin boundaries. This analysis aims to quantify the relationship of crystal orientation and stress magnitude to initiate mechanical twinning.

Transthyretin familial amyloid polyneuropathy (TTR-FAP): Parameters for early diagnosis.

PubMed

Escolano-Lozano, Fabiola; Barreiros, Ana Paula; Birklein, Frank; Geber, Christian

2018-01-01

Familial transthyretin amyloidosis is a life-threatening disease presenting with sensorimotor and autonomic polyneuropathy. Delayed diagnosis has a detrimental effect on treatment and prognosis. To facilitate diagnosis, we analyzed data patterns of patients with transthyretin familial amyloid polyneuropathy (TTR-FAP) and compared them to polyneuropathies of different etiology for clinical and electrophysiological discriminators. Twenty-four patients with TTR-FAP and 48 patients with diabetic polyneuropathy (dPNP) were investigated (neurological impairment score NIS; neurological disability score NDS) in a cross-sectional design. Both groups were matched for gender and presence of pain. Quantitative sensory testing (QST), sympathetic skin response (SSR), heart rate variability (HRV), and nerve conduction studies (NCV) were performed. Both groups were compared using univariate analysis. In a stepwise discriminant analysis, discriminators between both neuropathies were identified. These discriminators were validated comparing TTR-FAP patients with a cohort of patients with chemotherapy-induced polyneuropathy (CIN) and chronic inflammatory demyelinating neuropathy (CIDP). TTR-FAP patients scored higher in NDS and NIS and had impaired cold detection (CDT, p  = .024), cold-warm discrimination (TSL, p  = .019) and mechanical hyperalgesia (MPT, p  = .029) at the hands, SSR (upper limb, p  = .022) HRV and ulnar and sural NCS (all p  < .05) were more affected in TTR-FAP. Ulnar nerve sensory NCV, CDT, and the MPT but not the other parameters discriminated TTR-FAP from dPNP (82% of cases), from CIN (86.7%) and from CIDP (68%; only ulnar sNCV). Low ulnar SNCV, impaired cold perception, and mechanical hyperalgesia at the hands seem to characterize TTR-FAP and might help to differentiate from other polyneuropathies.

Chronological Lifespan in Yeast Is Dependent on the Accumulation of Storage Carbohydrates Mediated by Yak1, Mck1 and Rim15 Kinases

PubMed Central

Tang, Yingzhi; Quan, Zhenzhen; Zhang, Zhe; Oliver, Stephen G.; Zhang, Nianshu

2016-01-01

Upon starvation for glucose or any other macronutrient, yeast cells exit from the mitotic cell cycle and acquire a set of characteristics that are specific to quiescent cells to ensure longevity. Little is known about the molecular determinants that orchestrate quiescence entry and lifespan extension. Using starvation-specific gene reporters, we screened a subset of the yeast deletion library representing the genes encoding ‘signaling’ proteins. Apart from the previously characterised Rim15, Mck1 and Yak1 kinases, the SNF1/AMPK complex, the cell wall integrity pathway and a number of cell cycle regulators were shown to be necessary for proper quiescence establishment and for extension of chronological lifespan (CLS), suggesting that entry into quiescence requires the integration of starvation signals transmitted via multiple signaling pathways. The CLS of these signaling mutants, and those of the single, double and triple mutants of RIM15, YAK1 and MCK1 correlates well with the amount of storage carbohydrates but poorly with transition-phase cell cycle status. Combined removal of the glycogen and trehalose biosynthetic genes, especially GSY2 and TPS1, nearly abolishes the accumulation of storage carbohydrates and severely reduces CLS. Concurrent overexpression of GSY2 and TSL1 or supplementation of trehalose to the growth medium ameliorates the severe CLS defects displayed by the signaling mutants (rim15Δyak1Δ or rim15Δmck1Δ). Furthermore, we reveal that the levels of intracellular reactive oxygen species are cooperatively controlled by Yak1, Rim15 and Mck1, and the three kinases mediate the TOR1-regulated accumulation of storage carbohydrates and CLS extension. Our data support the hypothesis that metabolic reprogramming to accumulate energy stores and the activation of anti-oxidant defence systems are coordinated by Yak1, Rim15 and Mck1 kinases to ensure quiescence entry and lifespan extension in yeast. PMID:27923067

Chronological Lifespan in Yeast Is Dependent on the Accumulation of Storage Carbohydrates Mediated by Yak1, Mck1 and Rim15 Kinases.

PubMed

Cao, Lu; Tang, Yingzhi; Quan, Zhenzhen; Zhang, Zhe; Oliver, Stephen G; Zhang, Nianshu

2016-12-01

Upon starvation for glucose or any other macronutrient, yeast cells exit from the mitotic cell cycle and acquire a set of characteristics that are specific to quiescent cells to ensure longevity. Little is known about the molecular determinants that orchestrate quiescence entry and lifespan extension. Using starvation-specific gene reporters, we screened a subset of the yeast deletion library representing the genes encoding 'signaling' proteins. Apart from the previously characterised Rim15, Mck1 and Yak1 kinases, the SNF1/AMPK complex, the cell wall integrity pathway and a number of cell cycle regulators were shown to be necessary for proper quiescence establishment and for extension of chronological lifespan (CLS), suggesting that entry into quiescence requires the integration of starvation signals transmitted via multiple signaling pathways. The CLS of these signaling mutants, and those of the single, double and triple mutants of RIM15, YAK1 and MCK1 correlates well with the amount of storage carbohydrates but poorly with transition-phase cell cycle status. Combined removal of the glycogen and trehalose biosynthetic genes, especially GSY2 and TPS1, nearly abolishes the accumulation of storage carbohydrates and severely reduces CLS. Concurrent overexpression of GSY2 and TSL1 or supplementation of trehalose to the growth medium ameliorates the severe CLS defects displayed by the signaling mutants (rim15Δyak1Δ or rim15Δmck1Δ). Furthermore, we reveal that the levels of intracellular reactive oxygen species are cooperatively controlled by Yak1, Rim15 and Mck1, and the three kinases mediate the TOR1-regulated accumulation of storage carbohydrates and CLS extension. Our data support the hypothesis that metabolic reprogramming to accumulate energy stores and the activation of anti-oxidant defence systems are coordinated by Yak1, Rim15 and Mck1 kinases to ensure quiescence entry and lifespan extension in yeast.

Explosive Contamination from Substrate Surfaces: Differences and Similarities in Contamination Techniques Using RDX and C-4

NASA Astrophysics Data System (ADS)

Miller, C. J.; Yoder, T. S.

2010-06-01

Explosive trace detection equipment has been deployed to airports for more than a decade. During this time, the need for standardized procedures and calibrated trace amounts for ensuring that the systems are operating properly and detecting the correct explosive has been apparent but a standard representative of a fingerprint has been elusive. Standards are also necessary to evaluate instrumentation in the laboratories during development and prior to deployment to determine sample throughput, probability of detection, false positive/negative rates, ease of use by operator, mechanical and/or software problems that may be encountered, and other pertinent parameters that would result in the equipment being unusable during field operations. Since many laboratories do not have access to nor are allowed to handle explosives, the equipment is tested using techniques aimed at simulating the actual explosives fingerprint. This laboratory study focused on examining the similarities and differences in three different surface contamination techniques that are used to performance test explosive trace detection equipment in an attempt to determine how effective the techniques are at replicating actual field samples and to offer scenarios where each contamination technique is applicable. The three techniques used were dry transfer deposition of standard solutions using the Transportation Security Laboratory’s (TSL) patented dry transfer techniques (US patent 6470730), direct deposition of explosive standards onto substrates, and fingerprinting of actual explosives onto substrates. RDX was deposited on the surface of one of five substrates using one of the three different deposition techniques. The process was repeated for each substrate type using each contamination technique. The substrate types used were: 50% cotton/50% polyester as found in T-shirts, 100% cotton with a smooth surface such as that found in a cotton dress shirt, 100% cotton on a rough surface such as that found on canvas or denim, suede leather such as might be found on jackets, purses, or shoes, and painted metal obtained from a car hood at a junk yard. The samples were not pre-cleaned prior to testing and contained sizing agents, and in the case of the metal, oil and dirt. The substrates were photographed using a Zeiss Discover V12 stereoscope with Axiocam ICc1 3 megapixel digital camera to determine the difference in the crystalline structure and surface contamination in an attempt to determine differences and similarities associated with current contamination deposition techniques. Some samples were analyzed using scanning electron microscopy (SEM) and some were extracted and analyzed with high performance liquid chromatography (HPLC) or gas chromatography with an electron capture detector (GC-ECD) to quantify the data.

Evaluation of Quality Production Parameters and Mating Behavior of Novel Genetic Sexing Strains of the Mediterranean Fruit Fly Ceratitis capitata (Wiedemann) (Diptera: Tephritidae)

PubMed Central

Haq, Ihsan ul; Wornayporn, Viwat; Ahmad, Sohel; Sto Tomas, Ulysses; Dammalage, Thilakasiri; Gembinsky, Keke; Franz, Gerald; Cáceres, Carlos; Vreysen, Marc J. B.

2016-01-01

The Mediterranean fruit fly Ceratitis capitata (Wiedemann) (Diptera: Tephritidae) is one of the most important pest of fruits and vegetables in tropical and subtropical countries. The sterile insect technique (SIT) as a component of area-wide integrated pest management (AW-IPM) approaches is being used for the successful management of this pest. VIENNA 8 is a genetic sexing strain (GSS) that has a white pupae (wp) and temperature sensitive lethal (tsl) mutation, the latter killing all female embryos when eggs are exposed to high temperatures (34°C). The use of this GSS permits production and the release of only males which has increased the cost effectiveness of the SIT several fold for this pest. An efficient method of identification of recaptured sterile males can further increase the cost effectiveness of the SIT for this pest. Therefore, VIENNA 8-Sergeant2 (Sr2) strain and the transgenic strain VIENNA 8–1260 having visible markers were constructed. All three strains were evaluated for egg production, egg hatch, and egg sterility parameters under semi mass-rearing conditions and mating competitiveness in field cages. VIENNA 8–1260 females produced significantly fewer eggs as compared with the two other strains, which produced similar numbers of eggs. However, egg hatch of all strains was similar. Egg hatch of eggs produced by untreated females that had mated with adult males that had been irradiated with 100 Gy as pupae 2 days before emergence, was different for the three strains, i.e., egg hatch of 0.63%, 0.77%, 0.89% for VIENNA 8, VIENNA 8–1260, and VIENNA 8-Sr2, respectively. Differences in male mating competitiveness of the three strains against wild-type males were gradually reduced with successive generations under semi mass-rearing conditions. However, VIENNA 8 males adapted faster to laboratory conditions as compared with VIENNA 8-Sr2 and VIENNA 8–1260 males with respect to mating competitiveness. VIENNA 8 males of the F10 generation were equally competitive with wild-type males, whereas the mating competitiveness of VIENNA 8-Sr2 and VIENNA 8–1260 males was similar but lower as compared with wild-type males. Males from all three strains copulated earlier than wild-type males. Results are discussed in relation with the potential benefits of incorporating novel strains for more effective SIT application. PMID:27336737

Skeletal height estimation from regression analysis of sternal lengths in a Northwest Indian population of Chandigarh region: a postmortem study.

PubMed

Singh, Jagmahender; Pathak, R K; Chavali, Krishnadutt H

2011-03-20

Skeletal height estimation from regression analysis of eight sternal lengths in the subjects of Chandigarh zone of Northwest India is the topic of discussion in this study. Analysis of eight sternal lengths (length of manubrium, length of mesosternum, combined length of manubrium and mesosternum, total sternal length and first four intercostals lengths of mesosternum) measured from 252 male and 91 female sternums obtained at postmortems revealed that mean cadaver stature and sternal lengths were more in North Indians and males than the South Indians and females. Except intercostal lengths, all the sternal lengths were positively correlated with stature of the deceased in both sexes (P < 0.001). The multiple regression analysis of sternal lengths was found more useful than the linear regression for stature estimation. Using multivariate regression analysis, the combined length of manubrium and mesosternum in both sexes and the length of manubrium along with 2nd and 3rd intercostal lengths of mesosternum in males were selected as best estimators of stature. Nonetheless, the stature of males can be predicted with SEE of 6.66 (R(2) = 0.16, r = 0.318) from combination of MBL+BL_3+LM+BL_2, and in females from MBL only, it can be estimated with SEE of 6.65 (R(2) = 0.10, r = 0.318), whereas from the multiple regression analysis of pooled data, stature can be known with SEE of 6.97 (R(2) = 0.387, r = 575) from the combination of MBL+LM+BL_2+TSL+BL_3. The R(2) and F-ratio were found to be statistically significant for almost all the variables in both the sexes, except 4th intercostal length in males and 2nd to 4th intercostal lengths in females. The 'major' sternal lengths were more useful than the 'minor' ones for stature estimation The universal regression analysis used by Kanchan et al. [39] when applied to sternal lengths, gave satisfactory estimates of stature for males only but female stature was comparatively better estimated from simple linear regressions. But they are not proposed for the subjects of known sex, as they underestimate the male and overestimate female stature. However, intercostal lengths were found to be the poor estimators of stature (P < 0.05). And also sternal lengths exhibit weaker correlation coefficients and higher standard errors of estimate. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Prediction of vitamin interacting residues in a vitamin binding protein using evolutionary information

PubMed Central

2013-01-01

Background The vitamins are important cofactors in various enzymatic-reactions. In past, many inhibitors have been designed against vitamin binding pockets in order to inhibit vitamin-protein interactions. Thus, it is important to identify vitamin interacting residues in a protein. It is possible to detect vitamin-binding pockets on a protein, if its tertiary structure is known. Unfortunately tertiary structures of limited proteins are available. Therefore, it is important to develop in-silico models for predicting vitamin interacting residues in protein from its primary structure. Results In this study, first we compared protein-interacting residues of vitamins with other ligands using Two Sample Logo (TSL). It was observed that ATP, GTP, NAD, FAD and mannose preferred {G,R,K,S,H}, {G,K,T,S,D,N}, {T,G,Y}, {G,Y,W} and {Y,D,W,N,E} residues respectively, whereas vitamins preferred {Y,F,S,W,T,G,H} residues for the interaction with proteins. Furthermore, compositional information of preferred and non-preferred residues along with patterns-specificity was also observed within different vitamin-classes. Vitamins A, B and B6 preferred {F,I,W,Y,L,V}, {S,Y,G,T,H,W,N,E} and {S,T,G,H,Y,N} interacting residues respectively. It suggested that protein-binding patterns of vitamins are different from other ligands, and motivated us to develop separate predictor for vitamins and their sub-classes. The four different prediction modules, (i) vitamin interacting residues (VIRs), (ii) vitamin-A interacting residues (VAIRs), (iii) vitamin-B interacting residues (VBIRs) and (iv) pyridoxal-5-phosphate (vitamin B6) interacting residues (PLPIRs) have been developed. We applied various classifiers of SVM, BayesNet, NaiveBayes, ComplementNaiveBayes, NaiveBayesMultinomial, RandomForest and IBk etc., as machine learning techniques, using binary and Position-Specific Scoring Matrix (PSSM) features of protein sequences. Finally, we selected best performing SVM modules and obtained highest MCC of 0.53, 0.48, 0.61, 0.81 for VIRs, VAIRs, VBIRs, PLPIRs respectively, using PSSM-based evolutionary information. All the modules developed in this study have been trained and tested on non-redundant datasets and evaluated using five-fold cross-validation technique. The performances were also evaluated on the balanced and different independent datasets. Conclusions This study demonstrates that it is possible to predict VIRs, VAIRs, VBIRs and PLPIRs from evolutionary information of protein sequence. In order to provide service to the scientific community, we have developed web-server and standalone software VitaPred (http://crdd.osdd.net/raghava/vitapred/). PMID:23387468

Prediction of vitamin interacting residues in a vitamin binding protein using evolutionary information.

PubMed

Panwar, Bharat; Gupta, Sudheer; Raghava, Gajendra P S

2013-02-07

The vitamins are important cofactors in various enzymatic-reactions. In past, many inhibitors have been designed against vitamin binding pockets in order to inhibit vitamin-protein interactions. Thus, it is important to identify vitamin interacting residues in a protein. It is possible to detect vitamin-binding pockets on a protein, if its tertiary structure is known. Unfortunately tertiary structures of limited proteins are available. Therefore, it is important to develop in-silico models for predicting vitamin interacting residues in protein from its primary structure. In this study, first we compared protein-interacting residues of vitamins with other ligands using Two Sample Logo (TSL). It was observed that ATP, GTP, NAD, FAD and mannose preferred {G,R,K,S,H}, {G,K,T,S,D,N}, {T,G,Y}, {G,Y,W} and {Y,D,W,N,E} residues respectively, whereas vitamins preferred {Y,F,S,W,T,G,H} residues for the interaction with proteins. Furthermore, compositional information of preferred and non-preferred residues along with patterns-specificity was also observed within different vitamin-classes. Vitamins A, B and B6 preferred {F,I,W,Y,L,V}, {S,Y,G,T,H,W,N,E} and {S,T,G,H,Y,N} interacting residues respectively. It suggested that protein-binding patterns of vitamins are different from other ligands, and motivated us to develop separate predictor for vitamins and their sub-classes. The four different prediction modules, (i) vitamin interacting residues (VIRs), (ii) vitamin-A interacting residues (VAIRs), (iii) vitamin-B interacting residues (VBIRs) and (iv) pyridoxal-5-phosphate (vitamin B6) interacting residues (PLPIRs) have been developed. We applied various classifiers of SVM, BayesNet, NaiveBayes, ComplementNaiveBayes, NaiveBayesMultinomial, RandomForest and IBk etc., as machine learning techniques, using binary and Position-Specific Scoring Matrix (PSSM) features of protein sequences. Finally, we selected best performing SVM modules and obtained highest MCC of 0.53, 0.48, 0.61, 0.81 for VIRs, VAIRs, VBIRs, PLPIRs respectively, using PSSM-based evolutionary information. All the modules developed in this study have been trained and tested on non-redundant datasets and evaluated using five-fold cross-validation technique. The performances were also evaluated on the balanced and different independent datasets. This study demonstrates that it is possible to predict VIRs, VAIRs, VBIRs and PLPIRs from evolutionary information of protein sequence. In order to provide service to the scientific community, we have developed web-server and standalone software VitaPred (http://crdd.osdd.net/raghava/vitapred/).

A Systematic Study of Zerbar Lake Restoration

NASA Astrophysics Data System (ADS)

Hosseini, Reza; Oveis Torabi, Seyed; Forman Asgharzadeh, Deonna

2017-04-01

The beautiful lake of Zerbar, located near Marivan City at the west of Iran, is a freshwater lake with an area of 20 km2 and average depth of 5 meters. The lake is created by regional tectonic activities and is mainly fed with natural spring water from bottom. During the past three decades, regional development has caused much disturbance to the natural environment of the lake and its watershed. Rescuing the lake is crucial to the sustainability of the whole region. The study of Zerbar Restoration was performed with the aim to restore its health indicators. Variety of human activities in the watershed, as well as the multidisciplinary nature of lake restoration studies, made it necessary to develop a systematic approach to conduct the study. In Step I of restoration studies, satellite images were investigated to identify the historical changes of watershed during the past 30 years. Meanwhile, documents since 50 years ago were studied. Results indicate that farmland and graze land areas have been relatively constant during the past 50 years. Also, the area of lake, its riparian canes and floating plants have not changed much. In fact, the only significant land use change observed was the significant spread of Marivan City that has stretched toward the lake. The main physical variation to the lake has been elevating the southern edge of the lake by a constructing a landfill dam which was done to control the lake's overflow discharge for irrigation of downstream farmland development. Step II consists of studies performed by disciplines of water resources, hydrogeology, water quality, wetland and watershed ecology, agriculture, animal farming and fishery. Study results indicate that eutrophication (TSL>100), mainly caused by sewage from Marivan City and the surrounding rural areas has been the main reason for lake ecosystem degradation. DPSIR framework, as a novel approach in lake restoration, was applied to synthesize the study results of different disciplines in a systematic manner. In step III, stakeholder engagement was investigated through constitution analysis. Meetings were held to communicate lake damages obtained and classified through DPSIR Framework to the stakeholders. Then, stakeholder participation in different actions was achieved through additional meetings. Finally in Step IV, crucial restoration actions were identified: residents to manage rural and urban sewage and waste disposal through local governance, to plan and perform complementary study of lake water treatment (physical, chemical and biochemical methods), to plan and perform bottom sediment refinement, restoring the lake's natural hydrodynamic condition by adjusting the outlet level, local communities to help prevent landuse change from agriculture to villas, triggering the watershed master plan study to enable watershed monitoring, investigating water quality and discharge of bottom springs to better understand the lake's hydrological cycle, and finally, local residents to protect riparian vegetation.

Cross Sections of P-Induced Reactions up to 100 MeV for the Interpretation of Solar Cosmic Ray Produced Nuclides

NASA Astrophysics Data System (ADS)

Schiekel, T.; Rosel, R.; Herpers, U.; Bodemann, R.; Michel, R.; Dittrich, B.; Hofmann, H. J.; Suter, M.; Wolfli, W.; Holmqvist, B.; Conde, H.; Malmborg, P.

1992-07-01

Integral excitation functions for the production of residual nuclides by proton-induced reactions are the basic data for an accurate modelling of the interactions of solar cosmic ray (SCR) particles with extraterrestrial matter. Due to the relatively low energies (<200 MeV/A) of SCR particles the production of nuclear active secondary particles can be widely neglected and theoretical production rate depth profiles can be calculated by simply folding the depth dependent SCR spectra with thin target cross sections of the underlying nuclear reactions. The accuracy of such calculations exclusively depends on the quality of the available cross sections. For many nuclides, in particular for long-lived radionuclides and stable rare gas isotopes, the exis- ting cross section database is neither comprehensive nor reliable. Therefore, we started a series of experiments to improve this situation. Eighteen elements (C, N as Si3N4, O as SiO2, Mg, Al, Si, Ti, V, Mn as Mn/Ni-alloy, Fe, Co, Ni, Cu, Zr, Nb, Rh, Ba as Ba-contai- ning glass, and Au) were irradiated with 94 and 99 MeV protons at the external beam of the TSL-cyclotron at Uppsala. Cross sections were determined using the stacked foil technique. Beam monitoring was done by investigating the production of ^22Na from Al, for which evaluated cross sections exist. Residual nuclides were measured by X-, gamma- and accelerator-mass spectrometry. In order to check the quality of our experimental procedure some target elements (22 <= Z <= 28) were included in the new exper- iments, which had been formerly irradiated at Julich, at Louvain La Neuve, and at IPN Orsay. Comparisons between the earlier measurements (1,2) and the new cross sections showed excellent agreement. Up to now, cross sections were measured for more than 120 different reactions. Here, we report on the results obtained for the target elements C, N, O, Mg, Al, and Si. The status of experimental excitation functions for the production of some radionuclides relevant for SCR interactions with terrestrial and extraterrestrial matter, i.e., ^7Be and ^10Be from C, N, O, Mg, Al, and Si and ^22Na and ^26Al from Mg, Al, and Si, is discussed in detail. In order to investigate whether theoretical calculations can be used to supply the necessary cross sections for SCR model calcu- lations, a theoretical analysis of the experimental data is given on the basis of model calculations of equilibrium and pre-equilibrium reactions for light target elements. The new data are applied to model calculations of the production of SCR-produced nuclides in lunar surface materials and in meteorites. Acknowledgement: This work was supported by the Deutsche Forschungsgemeinschaft and by the Swiss National Science Foundation. References: (1) Michel et al. (1984) J. Geophys Res. 89, B673- B684. (2) Michel R. et al. (1985) Nucl. Phys. A441, 617-639.

A protocol for storage and long-distance shipment of Mediterranean fruit fly (Diptera: Tephritidae) eggs. II. Assessment of the optimal temperature and the substrate for male-only production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maman, E.; Caceres, C.

The present study has been conducted to assess the effect and interaction of various storage substrates and conditions on eggs of the Mediterranean fruit fly (medfly) Ceratitis capitata (Wiedemann). Tests were carried out with the genetic sexing strain VIENNA 8/D53, a strain that carries a temperature sensitive lethal (tsl) mutation that allows the selective killing of female zygotes. This study identifies strategies to enhance the storage and transport conditions through assessment of effect on egg, pupal and adult survival in order to facilitate the establishment of satellite mass rearing facilities for the production of male medflies. Eggs were immersed inmore » two different substrates and stored at different temperatures and for different time periods. Findings from this study suggest that egg storage periods, and to some extent, the storage substrates have significant effects on pupal and adult survival. For 72-h storage periods, the eggs preserved in agar solution at 10 deg. C produced the most pupae. There was an inverse relationship between the concentration of dissolved oxygen in the substrate during storage and the quality and survival of the stored/transported eggs. Apparently low levels of dissolved oxygen reduce metabolic rates, allowing the storage period to be prolonged. (author) [Spanish] El presente estudio fue conducido para evaluar el efecto e interaccion de varios substratos y condiciones de almacenamiento en huevos de la mosca mediterranea de la fruta, Ceratitis capitata (Wiedemann). Las pruebas se realizaron con la cepa en la cual es posible separar los sexos geneticamente VIENNA 8/D53, la cual contiene una mutacion letal sensible a la temperatura que permite la eliminacion selectiva de los zigotos femeninos. Este estudio identifica estrategias para mejorar las condiciones de almacenamiento y transporte por medio de la evaluacion de su efecto en la supervivencia de huevos, pupas y adultos, esto para facilitar el establecimiento de laboratorios satelites de cria masiva para la produccion de machos de la mosca mediterranea de la fruta. Los huevos fueron sumergidos en dos substratos diferentes y almacenados a diferente temperatura a diferentes periodos tiempos. Los resultados de este estudio sugieren que el periodo y hasta cierto punto el substrato de almacenamiento tienen un efecto significativo en la supervivencia de las pupas y los adultos. Para un periodo de almacenamiento de 72-h los huevos almacenados en solucion de agar a 10 deg. C producen un numero mayor de pupas. Hubo una relacion inversa entre la concentracion de oxigeno disuelto en el substrato durante el almacenamiento y la calidad y supervivencia de los huevos almacenados/transportados. Aparentemente los niveles bajos de oxigeno disuelto reducen el metabolismo y permiten que el periodo de almacenamiento pueda ser prolongado. (author)« less

Trichinella spiralis: strong antibody response to a 49 kDa newborn larva antigen in infected rats.

PubMed

Salinas-Tobon, Maria Del Rosario; Navarrete-Leon, Anaid; Mendez-Loredo, Blanca Esther; Esquivel-Aguirre, Dalia; Martínez-Abrajan, Dulce Maria; Hernandez-Sanchez, Javier

2007-02-01

In this work, we analyzed the kinetics of anti-Trichinella spiralis newborn larva (NBL) antibodies (Ab) and the antigenic recognition pattern of NBL proteins and its dose effects. Wistar rats were infected with 0, 700, 2000, 4000 and 8000 muscle larvae (ML) and bled at different time intervals up to day 31 post infection (p.i.). Ab production was higher with 2000 ML dose and decreased with 8000, 4000 and 700 ML. Abs were not detected until day 10, peaked on day 14 for the 2000 ML dose and on day 19 for the other doses and thereafter declined slowly from 19 to 31 days p.i. In contrast, Abs to ML increased from day 10, peaked on day 19 and remained high until the end of the study. Abs bound strongly at least to three NBL components of 188, 205 and 49 kDa. NBL antigen of 188 and 205 kDa were recognized 10-26 days p.i. and that of 49 kDa from day 10 to day 31 p.i. A weak recognition towards antigens of 52, 54, 62 and 83 kDa was also observed during the infection. An early recognition of 31, 43, 45, 55, 68 and 85 kDa ML antigens was observed whereas the response to those of 43, 45, 48, 60, 64 and 97 kDa (described previously as TSL-1 antigens) occurred late in the infection. A follow-up of antigen recognition up to day 61 with the optimal immunization dose (2000 ML) evidenced a decline of Ab production to the 49 kDa NBL antigen 42 days p.i., which suggested antigenic differences with the previously reported 43 kDa ML antigen strongly recognized late in the infection. To analyze the stage-specificity of the 49 kDa NBL antigen, polyclonal antibodies (PoAb) were obtained in rats immunized with 49 kDa NBL antigen. PoAb reacted strongly with the 49 kDa NBL component in NBL total soluble extract but no reactivity was observed with soluble antigen of the other T. spiralis stages. Albeit with less intensity, the 49 kDa component was also recognized by PoAb together with other antigens of 53, 97 and 107 kDa, in NBL excretory-secretory products (NBL-ESP). Thus, our results reveal differences in the kinetics of anti-NBL and ML Ab responses. While anti-NBL Abs declined slowly from day 19 until the end of the experiment, Abs to ML antigen remained high in the same period. It is remarkable the optimal Ab response to NBL antigens with 2000 ML infective dose and the reduced number of NBL antigens identified throughout the experimental T. spiralis infection, standing out the immunodominant 49 kDa antigen. Interestingly, this antigen, which was prominently expressed in NBL somatic proteins, was also detected in NBL-ESP.

Transforming Collaborative Process Models into Interface Process Models by Applying an MDA Approach

NASA Astrophysics Data System (ADS)

Lazarte, Ivanna M.; Chiotti, Omar; Villarreal, Pablo D.

Collaborative business models among enterprises require defining collaborative business processes. Enterprises implement B2B collaborations to execute these processes. In B2B collaborations the integration and interoperability of processes and systems of the enterprises are required to support the execution of collaborative processes. From a collaborative process model, which describes the global view of the enterprise interactions, each enterprise must define the interface process that represents the role it performs in the collaborative process in order to implement the process in a Business Process Management System. Hence, in this work we propose a method for the automatic generation of the interface process model of each enterprise from a collaborative process model. This method is based on a Model-Driven Architecture to transform collaborative process models into interface process models. By applying this method, interface processes are guaranteed to be interoperable and defined according to a collaborative process.

Extensible packet processing architecture

DOEpatents

Robertson, Perry J.; Hamlet, Jason R.; Pierson, Lyndon G.; Olsberg, Ronald R.; Chun, Guy D.

2013-08-20

A technique for distributed packet processing includes sequentially passing packets associated with packet flows between a plurality of processing engines along a flow through data bus linking the plurality of processing engines in series. At least one packet within a given packet flow is marked by a given processing engine to signify by the given processing engine to the other processing engines that the given processing engine has claimed the given packet flow for processing. A processing function is applied to each of the packet flows within the processing engines and the processed packets are output on a time-shared, arbitered data bus coupled to the plurality of processing engines.

Processed and ultra-processed foods are associated with lower-quality nutrient profiles in children from Colombia.

PubMed

Cornwell, Brittany; Villamor, Eduardo; Mora-Plazas, Mercedes; Marin, Constanza; Monteiro, Carlos A; Baylin, Ana

2018-01-01

To determine if processed and ultra-processed foods consumed by children in Colombia are associated with lower-quality nutrition profiles than less processed foods. We obtained information on sociodemographic and anthropometric variables and dietary information through dietary records and 24 h recalls from a convenience sample of the Bogotá School Children Cohort. Foods were classified into three categories: (i) unprocessed and minimally processed foods, (ii) processed culinary ingredients and (iii) processed and ultra-processed foods. We also examined the combination of unprocessed foods and processed culinary ingredients. Representative sample of children from low- to middle-income families in Bogotá, Colombia. Children aged 5-12 years in 2011 Bogotá School Children Cohort. We found that processed and ultra-processed foods are of lower dietary quality in general. Nutrients that were lower in processed and ultra-processed foods following adjustment for total energy intake included: n-3 PUFA, vitamins A, B12, C and E, Ca and Zn. Nutrients that were higher in energy-adjusted processed and ultra-processed foods compared with unprocessed foods included: Na, sugar and trans-fatty acids, although we also found that some healthy nutrients, including folate and Fe, were higher in processed and ultra-processed foods compared with unprocessed and minimally processed foods. Processed and ultra-processed foods generally have unhealthy nutrition profiles. Our findings suggest the categorization of foods based on processing characteristics is promising for understanding the influence of food processing on children's dietary quality. More studies accounting for the type and degree of food processing are needed.

Dynamic control of remelting processes

DOEpatents

Bertram, Lee A.; Williamson, Rodney L.; Melgaard, David K.; Beaman, Joseph J.; Evans, David G.

2000-01-01

An apparatus and method of controlling a remelting process by providing measured process variable values to a process controller; estimating process variable values using a process model of a remelting process; and outputting estimated process variable values from the process controller. Feedback and feedforward control devices receive the estimated process variable values and adjust inputs to the remelting process. Electrode weight, electrode mass, electrode gap, process current, process voltage, electrode position, electrode temperature, electrode thermal boundary layer thickness, electrode velocity, electrode acceleration, slag temperature, melting efficiency, cooling water temperature, cooling water flow rate, crucible temperature profile, slag skin temperature, and/or drip short events are employed, as are parameters representing physical constraints of electroslag remelting or vacuum arc remelting, as applicable.

On Intelligent Design and Planning Method of Process Route Based on Gun Breech Machining Process

NASA Astrophysics Data System (ADS)

Hongzhi, Zhao; Jian, Zhang

2018-03-01

The paper states an approach of intelligent design and planning of process route based on gun breech machining process, against several problems, such as complex machining process of gun breech, tedious route design and long period of its traditional unmanageable process route. Based on gun breech machining process, intelligent design and planning system of process route are developed by virtue of DEST and VC++. The system includes two functional modules--process route intelligent design and its planning. The process route intelligent design module, through the analysis of gun breech machining process, summarizes breech process knowledge so as to complete the design of knowledge base and inference engine. And then gun breech process route intelligently output. On the basis of intelligent route design module, the final process route is made, edited and managed in the process route planning module.

Gasoline from coal in the state of Illinois: feasibility study. Volume I. Design. [KBW gasification process, ICI low-pressure methanol process and Mobil M-gasoline process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-01-01

Volume 1 describes the proposed plant: KBW gasification process, ICI low-pressure methanol process and Mobil M-gasoline process, and also with ancillary processes, such as oxygen plant, shift process, RECTISOL purification process, sulfur recovery equipment and pollution control equipment. Numerous engineering diagrams are included. (LTN)

Performing a local reduction operation on a parallel computer

DOEpatents

Blocksome, Michael A; Faraj, Daniel A

2013-06-04

A parallel computer including compute nodes, each including two reduction processing cores, a network write processing core, and a network read processing core, each processing core assigned an input buffer. Copying, in interleaved chunks by the reduction processing cores, contents of the reduction processing cores' input buffers to an interleaved buffer in shared memory; copying, by one of the reduction processing cores, contents of the network write processing core's input buffer to shared memory; copying, by another of the reduction processing cores, contents of the network read processing core's input buffer to shared memory; and locally reducing in parallel by the reduction processing cores: the contents of the reduction processing core's input buffer; every other interleaved chunk of the interleaved buffer; the copied contents of the network write processing core's input buffer; and the copied contents of the network read processing core's input buffer.

Performing a local reduction operation on a parallel computer

DOEpatents

Blocksome, Michael A.; Faraj, Daniel A.

2012-12-11

A parallel computer including compute nodes, each including two reduction processing cores, a network write processing core, and a network read processing core, each processing core assigned an input buffer. Copying, in interleaved chunks by the reduction processing cores, contents of the reduction processing cores' input buffers to an interleaved buffer in shared memory; copying, by one of the reduction processing cores, contents of the network write processing core's input buffer to shared memory; copying, by another of the reduction processing cores, contents of the network read processing core's input buffer to shared memory; and locally reducing in parallel by the reduction processing cores: the contents of the reduction processing core's input buffer; every other interleaved chunk of the interleaved buffer; the copied contents of the network write processing core's input buffer; and the copied contents of the network read processing core's input buffer.

Situation awareness acquired from monitoring process plants - the Process Overview concept and measure.

PubMed

Lau, Nathan; Jamieson, Greg A; Skraaning, Gyrd

2016-07-01

We introduce Process Overview, a situation awareness characterisation of the knowledge derived from monitoring process plants. Process Overview is based on observational studies of process control work in the literature. The characterisation is applied to develop a query-based measure called the Process Overview Measure. The goal of the measure is to improve coupling between situation and awareness according to process plant properties and operator cognitive work. A companion article presents the empirical evaluation of the Process Overview Measure in a realistic process control setting. The Process Overview Measure demonstrated sensitivity and validity by revealing significant effects of experimental manipulations that corroborated with other empirical results. The measure also demonstrated adequate inter-rater reliability and practicality for measuring SA based on data collected by process experts. Practitioner Summary: The Process Overview Measure is a query-based measure for assessing operator situation awareness from monitoring process plants in representative settings.

43 CFR 2804.19 - How will BLM process my Processing Category 6 application?

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false How will BLM process my Processing... process my Processing Category 6 application? (a) For Processing Category 6 applications, you and BLM must enter into a written agreement that describes how BLM will process your application. The final agreement...

43 CFR 2804.19 - How will BLM process my Processing Category 6 application?

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false How will BLM process my Processing... process my Processing Category 6 application? (a) For Processing Category 6 applications, you and BLM must enter into a written agreement that describes how BLM will process your application. The final agreement...

Process Correlation Analysis Model for Process Improvement Identification

PubMed Central

Park, Sooyong

2014-01-01

Software process improvement aims at improving the development process of software systems. It is initiated by process assessment identifying strengths and weaknesses and based on the findings, improvement plans are developed. In general, a process reference model (e.g., CMMI) is used throughout the process of software process improvement as the base. CMMI defines a set of process areas involved in software development and what to be carried out in process areas in terms of goals and practices. Process areas and their elements (goals and practices) are often correlated due to the iterative nature of software development process. However, in the current practice, correlations of process elements are often overlooked in the development of an improvement plan, which diminishes the efficiency of the plan. This is mainly attributed to significant efforts and the lack of required expertise. In this paper, we present a process correlation analysis model that helps identify correlations of process elements from the results of process assessment. This model is defined based on CMMI and empirical data of improvement practices. We evaluate the model using industrial data. PMID:24977170

Process correlation analysis model for process improvement identification.

PubMed

Choi, Su-jin; Kim, Dae-Kyoo; Park, Sooyong

2014-01-01

Software process improvement aims at improving the development process of software systems. It is initiated by process assessment identifying strengths and weaknesses and based on the findings, improvement plans are developed. In general, a process reference model (e.g., CMMI) is used throughout the process of software process improvement as the base. CMMI defines a set of process areas involved in software development and what to be carried out in process areas in terms of goals and practices. Process areas and their elements (goals and practices) are often correlated due to the iterative nature of software development process. However, in the current practice, correlations of process elements are often overlooked in the development of an improvement plan, which diminishes the efficiency of the plan. This is mainly attributed to significant efforts and the lack of required expertise. In this paper, we present a process correlation analysis model that helps identify correlations of process elements from the results of process assessment. This model is defined based on CMMI and empirical data of improvement practices. We evaluate the model using industrial data.

Cleanliness of Ti-bearing Al-killed ultra-low-carbon steel during different heating processes

NASA Astrophysics Data System (ADS)

Guo, Jian-long; Bao, Yan-ping; Wang, Min

2017-12-01

During the production of Ti-bearing Al-killed ultra-low-carbon (ULC) steel, two different heating processes were used when the converter tapping temperature or the molten steel temperature in the Ruhrstahl-Heraeus (RH) process was low: heating by Al addition during the RH decarburization process and final deoxidation at the end of the RH decarburization process (process-I), and increasing the oxygen content at the end of RH decarburization, heating and final deoxidation by one-time Al addition (process-II). Temperature increases of 10°C by different processes were studied; the results showed that the two heating processes could achieve the same heating effect. The T.[O] content in the slab and the refining process was better controlled by process-I than by process-II. Statistical analysis of inclusions showed that the numbers of inclusions in the slab obtained by process-I were substantially less than those in the slab obtained by process-II. For process-I, the Al2O3 inclusions produced by Al added to induce heating were substantially removed at the end of decarburization. The amounts of inclusions were substantially greater for process-II than for process-I at different refining stages because of the higher dissolved oxygen concentration in process-II. Industrial test results showed that process-I was more beneficial for improving the cleanliness of molten steel.

Application of agent-based system for bioprocess description and process improvement.

PubMed

Gao, Ying; Kipling, Katie; Glassey, Jarka; Willis, Mark; Montague, Gary; Zhou, Yuhong; Titchener-Hooker, Nigel J

2010-01-01

Modeling plays an important role in bioprocess development for design and scale-up. Predictive models can also be used in biopharmaceutical manufacturing to assist decision-making either to maintain process consistency or to identify optimal operating conditions. To predict the whole bioprocess performance, the strong interactions present in a processing sequence must be adequately modeled. Traditionally, bioprocess modeling considers process units separately, which makes it difficult to capture the interactions between units. In this work, a systematic framework is developed to analyze the bioprocesses based on a whole process understanding and considering the interactions between process operations. An agent-based approach is adopted to provide a flexible infrastructure for the necessary integration of process models. This enables the prediction of overall process behavior, which can then be applied during process development or once manufacturing has commenced, in both cases leading to the capacity for fast evaluation of process improvement options. The multi-agent system comprises a process knowledge base, process models, and a group of functional agents. In this system, agent components co-operate with each other in performing their tasks. These include the description of the whole process behavior, evaluating process operating conditions, monitoring of the operating processes, predicting critical process performance, and providing guidance to decision-making when coping with process deviations. During process development, the system can be used to evaluate the design space for process operation. During manufacture, the system can be applied to identify abnormal process operation events and then to provide suggestions as to how best to cope with the deviations. In all cases, the function of the system is to ensure an efficient manufacturing process. The implementation of the agent-based approach is illustrated via selected application scenarios, which demonstrate how such a framework may enable the better integration of process operations by providing a plant-wide process description to facilitate process improvement. Copyright 2009 American Institute of Chemical Engineers

Electricity from sunlight. [low cost silicon for solar cells

NASA Technical Reports Server (NTRS)

Yaws, C. L.; Miller, J. W.; Lutwack, R.; Hsu, G.

1978-01-01

The paper discusses a number of new unconventional processes proposed for the low-cost production of silicon for solar cells. Consideration is given to: (1) the Battelle process (Zn/SiCl4), (2) the Battelle process (SiI4), (3) the Silane process, (4) the Motorola process (SiF4/SiF2), (5) the Westinghouse process (Na/SiCl4), (6) the Dow Corning process (C/SiO2), (7) the AeroChem process (SiCl4/H atom), and the Stanford process (Na/SiF4). Preliminary results indicate that the conventional process and the SiI4 processes cannot meet the project goal of $10/kg by 1986. Preliminary cost evaluation results for the Zn/SiCl4 process are favorable.

Composing Models of Geographic Physical Processes

NASA Astrophysics Data System (ADS)

Hofer, Barbara; Frank, Andrew U.

Processes are central for geographic information science; yet geographic information systems (GIS) lack capabilities to represent process related information. A prerequisite to including processes in GIS software is a general method to describe geographic processes independently of application disciplines. This paper presents such a method, namely a process description language. The vocabulary of the process description language is derived formally from mathematical models. Physical processes in geography can be described in two equivalent languages: partial differential equations or partial difference equations, where the latter can be shown graphically and used as a method for application specialists to enter their process models. The vocabulary of the process description language comprises components for describing the general behavior of prototypical geographic physical processes. These process components can be composed by basic models of geographic physical processes, which is shown by means of an example.

Process-based tolerance assessment of connecting rod machining process

NASA Astrophysics Data System (ADS)

Sharma, G. V. S. S.; Rao, P. Srinivasa; Surendra Babu, B.

2016-06-01

Process tolerancing based on the process capability studies is the optimistic and pragmatic approach of determining the manufacturing process tolerances. On adopting the define-measure-analyze-improve-control approach, the process potential capability index ( C p) and the process performance capability index ( C pk) values of identified process characteristics of connecting rod machining process are achieved to be greater than the industry benchmark of 1.33, i.e., four sigma level. The tolerance chain diagram methodology is applied to the connecting rod in order to verify the manufacturing process tolerances at various operations of the connecting rod manufacturing process. This paper bridges the gap between the existing dimensional tolerances obtained via tolerance charting and process capability studies of the connecting rod component. Finally, the process tolerancing comparison has been done by adopting a tolerance capability expert software.

Intranode data communications in a parallel computer

DOEpatents

Archer, Charles J; Blocksome, Michael A; Miller, Douglas R; Ratterman, Joseph D; Smith, Brian E

2014-01-07

Intranode data communications in a parallel computer that includes compute nodes configured to execute processes, where the data communications include: allocating, upon initialization of a first process of a computer node, a region of shared memory; establishing, by the first process, a predefined number of message buffers, each message buffer associated with a process to be initialized on the compute node; sending, to a second process on the same compute node, a data communications message without determining whether the second process has been initialized, including storing the data communications message in the message buffer of the second process; and upon initialization of the second process: retrieving, by the second process, a pointer to the second process's message buffer; and retrieving, by the second process from the second process's message buffer in dependence upon the pointer, the data communications message sent by the first process.

Intranode data communications in a parallel computer

DOEpatents

Archer, Charles J; Blocksome, Michael A; Miller, Douglas R; Ratterman, Joseph D; Smith, Brian E

2013-07-23

Intranode data communications in a parallel computer that includes compute nodes configured to execute processes, where the data communications include: allocating, upon initialization of a first process of a compute node, a region of shared memory; establishing, by the first process, a predefined number of message buffers, each message buffer associated with a process to be initialized on the compute node; sending, to a second process on the same compute node, a data communications message without determining whether the second process has been initialized, including storing the data communications message in the message buffer of the second process; and upon initialization of the second process: retrieving, by the second process, a pointer to the second process's message buffer; and retrieving, by the second process from the second process's message buffer in dependence upon the pointer, the data communications message sent by the first process.

Canadian Libraries and Mass Deacidification.

ERIC Educational Resources Information Center

Pacey, Antony

1992-01-01

Considers the advantages and disadvantages of six mass deacidification processes that libraries can use to salvage printed materials: the Wei T'o process, the Diethyl Zinc (DEZ) process, the FMC (Lithco) process, the Book Preservation Associates (BPA) process, the "Bookkeeper" process, and the "Lyophilization" process. The…

A new process sensitivity index to identify important system processes under process model and parametric uncertainty

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dai, Heng; Ye, Ming; Walker, Anthony P.

Hydrological models are always composed of multiple components that represent processes key to intended model applications. When a process can be simulated by multiple conceptual-mathematical models (process models), model uncertainty in representing the process arises. While global sensitivity analysis methods have been widely used for identifying important processes in hydrologic modeling, the existing methods consider only parametric uncertainty but ignore the model uncertainty for process representation. To address this problem, this study develops a new method to probe multimodel process sensitivity by integrating the model averaging methods into the framework of variance-based global sensitivity analysis, given that the model averagingmore » methods quantify both parametric and model uncertainty. A new process sensitivity index is derived as a metric of relative process importance, and the index includes variance in model outputs caused by uncertainty in both process models and model parameters. For demonstration, the new index is used to evaluate the processes of recharge and geology in a synthetic study of groundwater reactive transport modeling. The recharge process is simulated by two models that converting precipitation to recharge, and the geology process is also simulated by two models of different parameterizations of hydraulic conductivity; each process model has its own random parameters. The new process sensitivity index is mathematically general, and can be applied to a wide range of problems in hydrology and beyond.« less

Depth-of-processing effects on priming in stem completion: tests of the voluntary-contamination, conceptual-processing, and lexical-processing hypotheses.

PubMed

Richardson-Klavehn, A; Gardiner, J M

1998-05-01

Depth-of-processing effects on incidental perceptual memory tests could reflect (a) contamination by voluntary retrieval, (b) sensitivity of involuntary retrieval to prior conceptual processing, or (c) a deficit in lexical processing during graphemic study tasks that affects involuntary retrieval. The authors devised an extension of incidental test methodology--making conjunctive predictions about response times as well as response proportions--to discriminate among these alternatives. They used graphemic, phonemic, and semantic study tasks, and a word-stem completion test with incidental, intentional, and inclusion instructions. Semantic study processing was superior to phonemic study processing in the intentional and inclusion tests, but semantic and phonemic study processing produced equal priming in the incidental test, showing that priming was uncontaminated by voluntary retrieval--a conclusion reinforced by the response-time data--and that priming was insensitive to prior conceptual processing. The incidental test nevertheless showed a priming deficit following graphemic study processing, supporting the lexical-processing hypothesis. Adding a lexical decision to the 3 study tasks eliminated the priming deficit following graphemic study processing, but did not influence priming following phonemic and semantic processing. The results provide the first clear evidence that depth-of-processing effects on perceptual priming can reflect lexical processes, rather than voluntary contamination or conceptual processes.

Improving operational anodising process performance using simulation approach

NASA Astrophysics Data System (ADS)

Liong, Choong-Yeun; Ghazali, Syarah Syahidah

2015-10-01

The use of aluminium is very widespread, especially in transportation, electrical and electronics, architectural, automotive and engineering applications sectors. Therefore, the anodizing process is an important process for aluminium in order to make the aluminium durable, attractive and weather resistant. This research is focused on the anodizing process operations in manufacturing and supplying of aluminium extrusion. The data required for the development of the model is collected from the observations and interviews conducted in the study. To study the current system, the processes involved in the anodizing process are modeled by using Arena 14.5 simulation software. Those processes consist of five main processes, namely the degreasing process, the etching process, the desmut process, the anodizing process, the sealing process and 16 other processes. The results obtained were analyzed to identify the problems or bottlenecks that occurred and to propose improvement methods that can be implemented on the original model. Based on the comparisons that have been done between the improvement methods, the productivity could be increased by reallocating the workers and reducing loading time.

Value-driven process management: using value to improve processes.

PubMed

Melnyk, S A; Christensen, R T

2000-08-01

Every firm can be viewed as consisting of various processes. These processes affect everything that the firm does from accepting orders and designing products to scheduling production. In many firms, the management of processes often reflects considerations of efficiency (cost) rather than effectiveness (value). In this article, we introduce a well-structured process for managing processes that begins not with the process, but rather with the customer and the product and the concept of value. This process progresses through a number of steps which include issues such as defining value, generating the appropriate metrics, identifying the critical processes, mapping and assessing the performance of these processes, and identifying long- and short-term areas for action. What makes the approach presented in this article so powerful is that it explicitly links the customer to the process and that the process is evaluated in term of its ability to effectively serve the customers.

Method for routing events from key strokes in a multi-processing computer systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rhodes, D.A.; Rustici, E.; Carter, K.H.

1990-01-23

The patent describes a method of routing user input in a computer system which concurrently runs a plurality of processes. It comprises: generating keycodes representative of keys typed by a user; distinguishing generated keycodes by looking up each keycode in a routing table which assigns each possible keycode to an individual assigned process of the plurality of processes, one of which processes being a supervisory process; then, sending each keycode to its assigned process until a keycode assigned to the supervisory process is received; sending keycodes received subsequent to the keycode assigned to the supervisory process to a buffer; next,more » providing additional keycodes to the supervisory process from the buffer until the supervisory process has completed operation; and sending keycodes stored in the buffer to processes assigned therewith after the supervisory process has completedoperation.« less

Issues Management Process Course # 38401

DOE Office of Scientific and Technical Information (OSTI.GOV)

Binion, Ula Marie

The purpose of this training it to advise Issues Management Coordinators (IMCs) on the revised Contractor Assurance System (CAS) Issues Management (IM) process. Terminal Objectives: Understand the Laboratory’s IM process; Understand your role in the Laboratory’s IM process. Learning Objectives: Describe the IM process within the context of the CAS; Describe the importance of implementing an institutional IM process at LANL; Describe the process flow for the Laboratory’s IM process; Apply the definition of an issue; Use available resources to determine initial screening risk levels for issues; Describe the required major process steps for each risk level; Describe the personnelmore » responsibilities for IM process implementation; Access available resources to support IM process implementation.« less

Social network supported process recommender system.

PubMed

Ye, Yanming; Yin, Jianwei; Xu, Yueshen

2014-01-01

Process recommendation technologies have gained more and more attention in the field of intelligent business process modeling to assist the process modeling. However, most of the existing technologies only use the process structure analysis and do not take the social features of processes into account, while the process modeling is complex and comprehensive in most situations. This paper studies the feasibility of social network research technologies on process recommendation and builds a social network system of processes based on the features similarities. Then, three process matching degree measurements are presented and the system implementation is discussed subsequently. Finally, experimental evaluations and future works are introduced.

[Definition and stabilization of processes I. Management processes and support in a Urology Department].

PubMed

Pascual, Carlos; Luján, Marcos; Mora, José Ramón; Chiva, Vicente; Gamarra, Manuela

2015-01-01

The implantation of total quality management models in clinical departments can better adapt to the 2009 ISO 9004 model. An essential part of implantation of these models is the establishment of processes and their stabilization. There are four types of processes: key, management, support and operative (clinical). Management processes have four parts: process stabilization form, process procedures form, medical activities cost estimation form and, process flow chart. In this paper we will detail the creation of an essential process in a surgical department, such as the process of management of the surgery waiting list.

T-Check in Technologies for Interoperability: Business Process Management in a Web Services Context

DTIC Science & Technology

2008-09-01

UML Sequence Diagram) 6  Figure 3:   BPMN Diagram of the Order Processing Business Process 9  Figure 4:   T-Check Process for Technology Evaluation 10...Figure 5:  Notional System Architecture 12  Figure 6:  Flow Chart of the Order Processing Business Process 14  Figure 7:  Order Processing Activities...features. Figure 3 (created with Intalio BPMS Designer [Intalio 2008]) shows a BPMN view of the Order Processing business process that is used in the

A case study: application of statistical process control tool for determining process capability and sigma level.

PubMed

Chopra, Vikram; Bairagi, Mukesh; Trivedi, P; Nagar, Mona

2012-01-01

Statistical process control is the application of statistical methods to the measurement and analysis of variation process. Various regulatory authorities such as Validation Guidance for Industry (2011), International Conference on Harmonisation ICH Q10 (2009), the Health Canada guidelines (2009), Health Science Authority, Singapore: Guidance for Product Quality Review (2008), and International Organization for Standardization ISO-9000:2005 provide regulatory support for the application of statistical process control for better process control and understanding. In this study risk assessments, normal probability distributions, control charts, and capability charts are employed for selection of critical quality attributes, determination of normal probability distribution, statistical stability, and capability of production processes, respectively. The objective of this study is to determine tablet production process quality in the form of sigma process capability. By interpreting data and graph trends, forecasting of critical quality attributes, sigma process capability, and stability of process were studied. The overall study contributes to an assessment of process at the sigma level with respect to out-of-specification attributes produced. Finally, the study will point to an area where the application of quality improvement and quality risk assessment principles for achievement of six sigma-capable processes is possible. Statistical process control is the most advantageous tool for determination of the quality of any production process. This tool is new for the pharmaceutical tablet production process. In the case of pharmaceutical tablet production processes, the quality control parameters act as quality assessment parameters. Application of risk assessment provides selection of critical quality attributes among quality control parameters. Sequential application of normality distributions, control charts, and capability analyses provides a valid statistical process control study on process. Interpretation of such a study provides information about stability, process variability, changing of trends, and quantification of process ability against defective production. Comparative evaluation of critical quality attributes by Pareto charts provides the least capable and most variable process that is liable for improvement. Statistical process control thus proves to be an important tool for six sigma-capable process development and continuous quality improvement.

A practical approach for exploration and modeling of the design space of a bacterial vaccine cultivation process.

PubMed

Streefland, M; Van Herpen, P F G; Van de Waterbeemd, B; Van der Pol, L A; Beuvery, E C; Tramper, J; Martens, D E; Toft, M

2009-10-15

A licensed pharmaceutical process is required to be executed within the validated ranges throughout the lifetime of product manufacturing. Changes to the process, especially for processes involving biological products, usually require the manufacturer to demonstrate that the safety and efficacy of the product remains unchanged by new or additional clinical testing. Recent changes in the regulations for pharmaceutical processing allow broader ranges of process settings to be submitted for regulatory approval, the so-called process design space, which means that a manufacturer can optimize his process within the submitted ranges after the product has entered the market, which allows flexible processes. In this article, the applicability of this concept of the process design space is investigated for the cultivation process step for a vaccine against whooping cough disease. An experimental design (DoE) is applied to investigate the ranges of critical process parameters that still result in a product that meets specifications. The on-line process data, including near infrared spectroscopy, are used to build a descriptive model of the processes used in the experimental design. Finally, the data of all processes are integrated in a multivariate batch monitoring model that represents the investigated process design space. This article demonstrates how the general principles of PAT and process design space can be applied for an undefined biological product such as a whole cell vaccine. The approach chosen for model development described here, allows on line monitoring and control of cultivation batches in order to assure in real time that a process is running within the process design space.

Processing approaches to cognition: the impetus from the levels-of-processing framework.

PubMed

Roediger, Henry L; Gallo, David A; Geraci, Lisa

2002-01-01

Processing approaches to cognition have a long history, from act psychology to the present, but perhaps their greatest boost was given by the success and dominance of the levels-of-processing framework. We review the history of processing approaches, and explore the influence of the levels-of-processing approach, the procedural approach advocated by Paul Kolers, and the transfer-appropriate processing framework. Processing approaches emphasise the procedures of mind and the idea that memory storage can be usefully conceptualised as residing in the same neural units that originally processed information at the time of encoding. Processing approaches emphasise the unity and interrelatedness of cognitive processes and maintain that they can be dissected into separate faculties only by neglecting the richness of mental life. We end by pointing to future directions for processing approaches.

Global Sensitivity Analysis for Process Identification under Model Uncertainty

NASA Astrophysics Data System (ADS)

Ye, M.; Dai, H.; Walker, A. P.; Shi, L.; Yang, J.

2015-12-01

The environmental system consists of various physical, chemical, and biological processes, and environmental models are always built to simulate these processes and their interactions. For model building, improvement, and validation, it is necessary to identify important processes so that limited resources can be used to better characterize the processes. While global sensitivity analysis has been widely used to identify important processes, the process identification is always based on deterministic process conceptualization that uses a single model for representing a process. However, environmental systems are complex, and it happens often that a single process may be simulated by multiple alternative models. Ignoring the model uncertainty in process identification may lead to biased identification in that identified important processes may not be so in the real world. This study addresses this problem by developing a new method of global sensitivity analysis for process identification. The new method is based on the concept of Sobol sensitivity analysis and model averaging. Similar to the Sobol sensitivity analysis to identify important parameters, our new method evaluates variance change when a process is fixed at its different conceptualizations. The variance considers both parametric and model uncertainty using the method of model averaging. The method is demonstrated using a synthetic study of groundwater modeling that considers recharge process and parameterization process. Each process has two alternative models. Important processes of groundwater flow and transport are evaluated using our new method. The method is mathematically general, and can be applied to a wide range of environmental problems.

A new process sensitivity index to identify important system processes under process model and parametric uncertainty

DOE PAGES

Dai, Heng; Ye, Ming; Walker, Anthony P.; ...

2017-03-28

A hydrological model consists of multiple process level submodels, and each submodel represents a process key to the operation of the simulated system. Global sensitivity analysis methods have been widely used to identify important processes for system model development and improvement. The existing methods of global sensitivity analysis only consider parametric uncertainty, and are not capable of handling model uncertainty caused by multiple process models that arise from competing hypotheses about one or more processes. To address this problem, this study develops a new method to probe model output sensitivity to competing process models by integrating model averaging methods withmore » variance-based global sensitivity analysis. A process sensitivity index is derived as a single summary measure of relative process importance, and the index includes variance in model outputs caused by uncertainty in both process models and their parameters. Here, for demonstration, the new index is used to assign importance to the processes of recharge and geology in a synthetic study of groundwater reactive transport modeling. The recharge process is simulated by two models that convert precipitation to recharge, and the geology process is simulated by two models of hydraulic conductivity. Each process model has its own random parameters. Finally, the new process sensitivity index is mathematically general, and can be applied to a wide range of problems in hydrology and beyond.« less

A new process sensitivity index to identify important system processes under process model and parametric uncertainty

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dai, Heng; Ye, Ming; Walker, Anthony P.

A hydrological model consists of multiple process level submodels, and each submodel represents a process key to the operation of the simulated system. Global sensitivity analysis methods have been widely used to identify important processes for system model development and improvement. The existing methods of global sensitivity analysis only consider parametric uncertainty, and are not capable of handling model uncertainty caused by multiple process models that arise from competing hypotheses about one or more processes. To address this problem, this study develops a new method to probe model output sensitivity to competing process models by integrating model averaging methods withmore » variance-based global sensitivity analysis. A process sensitivity index is derived as a single summary measure of relative process importance, and the index includes variance in model outputs caused by uncertainty in both process models and their parameters. Here, for demonstration, the new index is used to assign importance to the processes of recharge and geology in a synthetic study of groundwater reactive transport modeling. The recharge process is simulated by two models that convert precipitation to recharge, and the geology process is simulated by two models of hydraulic conductivity. Each process model has its own random parameters. Finally, the new process sensitivity index is mathematically general, and can be applied to a wide range of problems in hydrology and beyond.« less

Social Network Supported Process Recommender System

PubMed Central

Ye, Yanming; Yin, Jianwei; Xu, Yueshen

2014-01-01

Process recommendation technologies have gained more and more attention in the field of intelligent business process modeling to assist the process modeling. However, most of the existing technologies only use the process structure analysis and do not take the social features of processes into account, while the process modeling is complex and comprehensive in most situations. This paper studies the feasibility of social network research technologies on process recommendation and builds a social network system of processes based on the features similarities. Then, three process matching degree measurements are presented and the system implementation is discussed subsequently. Finally, experimental evaluations and future works are introduced. PMID:24672309

A model for process representation and synthesis. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Thomas, R. H.

1971-01-01

The problem of representing groups of loosely connected processes is investigated, and a model for process representation useful for synthesizing complex patterns of process behavior is developed. There are three parts, the first part isolates the concepts which form the basis for the process representation model by focusing on questions such as: What is a process; What is an event; Should one process be able to restrict the capabilities of another? The second part develops a model for process representation which captures the concepts and intuitions developed in the first part. The model presented is able to describe both the internal structure of individual processes and the interface structure between interacting processes. Much of the model's descriptive power derives from its use of the notion of process state as a vehicle for relating the internal and external aspects of process behavior. The third part demonstrates by example that the model for process representation is a useful one for synthesizing process behavior patterns. In it the model is used to define a variety of interesting process behavior patterns. The dissertation closes by suggesting how the model could be used as a semantic base for a very potent language extension facility.

Process and Post-Process: A Discursive History.

ERIC Educational Resources Information Center

Matsuda, Paul Kei

2003-01-01

Examines the history of process and post-process in composition studies, focusing on ways in which terms, such as "current-traditional rhetoric,""process," and "post-process" have contributed to the discursive construction of reality. Argues that use of the term post-process in the context of second language writing needs to be guided by a…

Improving operational anodising process performance using simulation approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liong, Choong-Yeun, E-mail: lg@ukm.edu.my; Ghazali, Syarah Syahidah, E-mail: syarah@gapps.kptm.edu.my

The use of aluminium is very widespread, especially in transportation, electrical and electronics, architectural, automotive and engineering applications sectors. Therefore, the anodizing process is an important process for aluminium in order to make the aluminium durable, attractive and weather resistant. This research is focused on the anodizing process operations in manufacturing and supplying of aluminium extrusion. The data required for the development of the model is collected from the observations and interviews conducted in the study. To study the current system, the processes involved in the anodizing process are modeled by using Arena 14.5 simulation software. Those processes consist ofmore » five main processes, namely the degreasing process, the etching process, the desmut process, the anodizing process, the sealing process and 16 other processes. The results obtained were analyzed to identify the problems or bottlenecks that occurred and to propose improvement methods that can be implemented on the original model. Based on the comparisons that have been done between the improvement methods, the productivity could be increased by reallocating the workers and reducing loading time.« less

Feller processes: the next generation in modeling. Brownian motion, Lévy processes and beyond.

PubMed

Böttcher, Björn

2010-12-03

We present a simple construction method for Feller processes and a framework for the generation of sample paths of Feller processes. The construction is based on state space dependent mixing of Lévy processes. Brownian Motion is one of the most frequently used continuous time Markov processes in applications. In recent years also Lévy processes, of which Brownian Motion is a special case, have become increasingly popular. Lévy processes are spatially homogeneous, but empirical data often suggest the use of spatially inhomogeneous processes. Thus it seems necessary to go to the next level of generalization: Feller processes. These include Lévy processes and in particular brownian motion as special cases but allow spatial inhomogeneities. Many properties of Feller processes are known, but proving the very existence is, in general, very technical. Moreover, an applicable framework for the generation of sample paths of a Feller process was missing. We explain, with practitioners in mind, how to overcome both of these obstacles. In particular our simulation technique allows to apply Monte Carlo methods to Feller processes.

Feller Processes: The Next Generation in Modeling. Brownian Motion, Lévy Processes and Beyond

PubMed Central

Böttcher, Björn

2010-01-01

We present a simple construction method for Feller processes and a framework for the generation of sample paths of Feller processes. The construction is based on state space dependent mixing of Lévy processes. Brownian Motion is one of the most frequently used continuous time Markov processes in applications. In recent years also Lévy processes, of which Brownian Motion is a special case, have become increasingly popular. Lévy processes are spatially homogeneous, but empirical data often suggest the use of spatially inhomogeneous processes. Thus it seems necessary to go to the next level of generalization: Feller processes. These include Lévy processes and in particular Brownian motion as special cases but allow spatial inhomogeneities. Many properties of Feller processes are known, but proving the very existence is, in general, very technical. Moreover, an applicable framework for the generation of sample paths of a Feller process was missing. We explain, with practitioners in mind, how to overcome both of these obstacles. In particular our simulation technique allows to apply Monte Carlo methods to Feller processes. PMID:21151931

AIRSAR Automated Web-based Data Processing and Distribution System

NASA Technical Reports Server (NTRS)

Chu, Anhua; vanZyl, Jakob; Kim, Yunjin; Lou, Yunling; Imel, David; Tung, Wayne; Chapman, Bruce; Durden, Stephen

2005-01-01

In this paper, we present an integrated, end-to-end synthetic aperture radar (SAR) processing system that accepts data processing requests, submits processing jobs, performs quality analysis, delivers and archives processed data. This fully automated SAR processing system utilizes database and internet/intranet web technologies to allow external users to browse and submit data processing requests and receive processed data. It is a cost-effective way to manage a robust SAR processing and archival system. The integration of these functions has reduced operator errors and increased processor throughput dramatically.

Simplified process model discovery based on role-oriented genetic mining.

PubMed

Zhao, Weidong; Liu, Xi; Dai, Weihui

2014-01-01

Process mining is automated acquisition of process models from event logs. Although many process mining techniques have been developed, most of them are based on control flow. Meanwhile, the existing role-oriented process mining methods focus on correctness and integrity of roles while ignoring role complexity of the process model, which directly impacts understandability and quality of the model. To address these problems, we propose a genetic programming approach to mine the simplified process model. Using a new metric of process complexity in terms of roles as the fitness function, we can find simpler process models. The new role complexity metric of process models is designed from role cohesion and coupling, and applied to discover roles in process models. Moreover, the higher fitness derived from role complexity metric also provides a guideline for redesigning process models. Finally, we conduct case study and experiments to show that the proposed method is more effective for streamlining the process by comparing with related studies.

Electrotechnologies to process foods

USDA-ARS?s Scientific Manuscript database

Electrical energy is being used to process foods. In conventional food processing plants, electricity drives mechanical devices and controls the degree of process. In recent years, several processing technologies are being developed to process foods directly with electricity. Electrotechnologies use...

Challenges associated with the implementation of the nursing process: A systematic review.

PubMed

Zamanzadeh, Vahid; Valizadeh, Leila; Tabrizi, Faranak Jabbarzadeh; Behshid, Mojghan; Lotfi, Mojghan

2015-01-01

Nursing process is a scientific approach in the provision of qualified nursing cares. However, in practice, the implementation of this process is faced with numerous challenges. With the knowledge of the challenges associated with the implementation of the nursing process, the nursing processes can be developed appropriately. Due to the lack of comprehensive information on this subject, the current study was carried out to assess the key challenges associated with the implementation of the nursing process. To achieve and review related studies on this field, databases of Iran medix, SID, Magiran, PUBMED, Google scholar, and Proquest were assessed using the main keywords of nursing process and nursing process systematic review. The articles were retrieved in three steps including searching by keywords, review of the proceedings based on inclusion criteria, and final retrieval and assessment of available full texts. Systematic assessment of the articles showed different challenges in implementation of the nursing process. Intangible understanding of the concept of nursing process, different views of the process, lack of knowledge and awareness among nurses related to the execution of process, supports of managing systems, and problems related to recording the nursing process were the main challenges that were extracted from review of literature. On systematically reviewing the literature, intangible understanding of the concept of nursing process has been identified as the main challenge in nursing process. To achieve the best strategy to minimize the challenge, in addition to preparing facilitators for implementation of nursing process, intangible understanding of the concept of nursing process, different views of the process, and forming teams of experts in nursing education are recommended for internalizing the nursing process among nurses.

Challenges associated with the implementation of the nursing process: A systematic review

PubMed Central

Zamanzadeh, Vahid; Valizadeh, Leila; Tabrizi, Faranak Jabbarzadeh; Behshid, Mojghan; Lotfi, Mojghan

2015-01-01

Background: Nursing process is a scientific approach in the provision of qualified nursing cares. However, in practice, the implementation of this process is faced with numerous challenges. With the knowledge of the challenges associated with the implementation of the nursing process, the nursing processes can be developed appropriately. Due to the lack of comprehensive information on this subject, the current study was carried out to assess the key challenges associated with the implementation of the nursing process. Materials and Methods: To achieve and review related studies on this field, databases of Iran medix, SID, Magiran, PUBMED, Google scholar, and Proquest were assessed using the main keywords of nursing process and nursing process systematic review. The articles were retrieved in three steps including searching by keywords, review of the proceedings based on inclusion criteria, and final retrieval and assessment of available full texts. Results: Systematic assessment of the articles showed different challenges in implementation of the nursing process. Intangible understanding of the concept of nursing process, different views of the process, lack of knowledge and awareness among nurses related to the execution of process, supports of managing systems, and problems related to recording the nursing process were the main challenges that were extracted from review of literature. Conclusions: On systematically reviewing the literature, intangible understanding of the concept of nursing process has been identified as the main challenge in nursing process. To achieve the best strategy to minimize the challenge, in addition to preparing facilitators for implementation of nursing process, intangible understanding of the concept of nursing process, different views of the process, and forming teams of experts in nursing education are recommended for internalizing the nursing process among nurses. PMID:26257793

Automated synthesis of image processing procedures using AI planning techniques

NASA Technical Reports Server (NTRS)

Chien, Steve; Mortensen, Helen

1994-01-01

This paper describes the Multimission VICAR (Video Image Communication and Retrieval) Planner (MVP) (Chien 1994) system, which uses artificial intelligence planning techniques (Iwasaki & Friedland, 1985, Pemberthy & Weld, 1992, Stefik, 1981) to automatically construct executable complex image processing procedures (using models of the smaller constituent image processing subprograms) in response to image processing requests made to the JPL Multimission Image Processing Laboratory (MIPL). The MVP system allows the user to specify the image processing requirements in terms of the various types of correction required. Given this information, MVP derives unspecified required processing steps and determines appropriate image processing programs and parameters to achieve the specified image processing goals. This information is output as an executable image processing program which can then be executed to fill the processing request.

Optimisation of shock absorber process parameters using failure mode and effect analysis and genetic algorithm

NASA Astrophysics Data System (ADS)

Mariajayaprakash, Arokiasamy; Senthilvelan, Thiyagarajan; Vivekananthan, Krishnapillai Ponnambal

2013-07-01

The various process parameters affecting the quality characteristics of the shock absorber during the process were identified using the Ishikawa diagram and by failure mode and effect analysis. The identified process parameters are welding process parameters (squeeze, heat control, wheel speed, and air pressure), damper sealing process parameters (load, hydraulic pressure, air pressure, and fixture height), washing process parameters (total alkalinity, temperature, pH value of rinsing water, and timing), and painting process parameters (flowability, coating thickness, pointage, and temperature). In this paper, the process parameters, namely, painting and washing process parameters, are optimized by Taguchi method. Though the defects are reasonably minimized by Taguchi method, in order to achieve zero defects during the processes, genetic algorithm technique is applied on the optimized parameters obtained by Taguchi method.

Methods, media and systems for managing a distributed application running in a plurality of digital processing devices

DOEpatents

Laadan, Oren; Nieh, Jason; Phung, Dan

2012-10-02

Methods, media and systems for managing a distributed application running in a plurality of digital processing devices are provided. In some embodiments, a method includes running one or more processes associated with the distributed application in virtualized operating system environments on a plurality of digital processing devices, suspending the one or more processes, and saving network state information relating to network connections among the one or more processes. The method further include storing process information relating to the one or more processes, recreating the network connections using the saved network state information, and restarting the one or more processes using the stored process information.

SEMICONDUCTOR TECHNOLOGY A signal processing method for the friction-based endpoint detection system of a CMP process

NASA Astrophysics Data System (ADS)

Chi, Xu; Dongming, Guo; Zhuji, Jin; Renke, Kang

2010-12-01

A signal processing method for the friction-based endpoint detection system of a chemical mechanical polishing (CMP) process is presented. The signal process method uses the wavelet threshold denoising method to reduce the noise contained in the measured original signal, extracts the Kalman filter innovation from the denoised signal as the feature signal, and judges the CMP endpoint based on the feature of the Kalman filter innovation sequence during the CMP process. Applying the signal processing method, the endpoint detection experiments of the Cu CMP process were carried out. The results show that the signal processing method can judge the endpoint of the Cu CMP process.

Composite faces are not (necessarily) processed coactively: A test using systems factorial technology and logical-rule models.

PubMed

Cheng, Xue Jun; McCarthy, Callum J; Wang, Tony S L; Palmeri, Thomas J; Little, Daniel R

2018-06-01

Upright faces are thought to be processed more holistically than inverted faces. In the widely used composite face paradigm, holistic processing is inferred from interference in recognition performance from a to-be-ignored face half for upright and aligned faces compared with inverted or misaligned faces. We sought to characterize the nature of holistic processing in composite faces in computational terms. We use logical-rule models (Fifić, Little, & Nosofsky, 2010) and Systems Factorial Technology (Townsend & Nozawa, 1995) to examine whether composite faces are processed through pooling top and bottom face halves into a single processing channel-coactive processing-which is one common mechanistic definition of holistic processing. By specifically operationalizing holistic processing as the pooling of features into a single decision process in our task, we are able to distinguish it from other processing models that may underlie composite face processing. For instance, a failure of selective attention might result even when top and bottom components of composite faces are processed in serial or in parallel without processing the entire face coactively. Our results show that performance is best explained by a mixture of serial and parallel processing architectures across all 4 upright and inverted, aligned and misaligned face conditions. The results indicate multichannel, featural processing of composite faces in a manner inconsistent with the notion of coactivity. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Fuzzy image processing in sun sensor

NASA Technical Reports Server (NTRS)

Mobasser, S.; Liebe, C. C.; Howard, A.

2003-01-01

This paper will describe how the fuzzy image processing is implemented in the instrument. Comparison of the Fuzzy image processing and a more conventional image processing algorithm is provided and shows that the Fuzzy image processing yields better accuracy then conventional image processing.

DESIGNING ENVIRONMENTAL, ECONOMIC AND ENERGY EFFICIENT CHEMICAL PROCESSES

EPA Science Inventory

The design and improvement of chemical processes can be very challenging. The earlier energy conservation, process economics and environmental aspects are incorporated into the process development, the easier and less expensive it is to alter the process design. Process emissio...

Reversing the conventional leather processing sequence for cleaner leather production.

PubMed

Saravanabhavan, Subramani; Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasami, Thirumalachari

2006-02-01

Conventional leather processing generally involves a combination of single and multistep processes that employs as well as expels various biological, inorganic, and organic materials. It involves nearly 14-15 steps and discharges a huge amount of pollutants. This is primarily due to the fact that conventional leather processing employs a "do-undo" process logic. In this study, the conventional leather processing steps have been reversed to overcome the problems associated with the conventional method. The charges of the skin matrix and of the chemicals and pH profiles of the process have been judiciously used for reversing the process steps. This reversed process eventually avoids several acidification and basification/neutralization steps used in conventional leather processing. The developed process has been validated through various analyses such as chromium content, shrinkage temperature, softness measurements, scanning electron microscopy, and physical testing of the leathers. Further, the performance of the leathers is shown to be on par with conventionally processed leathers through bulk property evaluation. The process enjoys a significant reduction in COD and TS by 53 and 79%, respectively. Water consumption and discharge is reduced by 65 and 64%, respectively. Also, the process benefits from significant reduction in chemicals, time, power, and cost compared to the conventional process.

Group processing in an undergraduate biology course for preservice teachers: Experiences and attitudes

NASA Astrophysics Data System (ADS)

Schellenberger, Lauren Brownback

Group processing is a key principle of cooperative learning in which small groups discuss their strengths and weaknesses and set group goals or norms. However, group processing has not been well-studied at the post-secondary level or from a qualitative or mixed methods perspective. This mixed methods study uses a phenomenological framework to examine the experience of group processing for students in an undergraduate biology course for preservice teachers. The effect of group processing on students' attitudes toward future group work and group processing is also examined. Additionally, this research investigated preservice teachers' plans for incorporating group processing into future lessons. Students primarily experienced group processing as a time to reflect on past performance. Also, students experienced group processing as a time to increase communication among group members and become motivated for future group assignments. Three factors directly influenced students' experiences with group processing: (1) previous experience with group work, (2) instructor interaction, and (3) gender. Survey data indicated that group processing had a slight positive effect on students' attitudes toward future group work and group processing. Participants who were interviewed felt that group processing was an important part of group work and that it had increased their group's effectiveness as well as their ability to work effectively with other people. Participants held positive views on group work prior to engaging in group processing, and group processing did not alter their atittude toward group work. Preservice teachers who were interviewed planned to use group work and a modified group processing protocol in their future classrooms. They also felt that group processing had prepared them for their future professions by modeling effective collaboration and group skills. Based on this research, a new model for group processing has been created which includes extensive instructor interaction and additional group processing sessions. This study offers a new perspective on the phenomenon of group processing and informs science educators and teacher educators on the effective implementation of this important component of small-group learning.

Properties of the Bivariate Delayed Poisson Process

DTIC Science & Technology

1974-07-01

and Lewis (1972) in their Berkeley Symposium paper and here their analysis of the bivariate Poisson processes (without Poisson noise) is carried... Poisson processes . They cannot, however, be independent Poisson processes because their events are associated in pairs by the displace- ment centres...process because its marginal processes for events of each type are themselves (univariate) Poisson processes . Cox and Lewis (1972) assumed a

The Application of Six Sigma Methodologies to University Processes: The Use of Student Teams

ERIC Educational Resources Information Center

Pryor, Mildred Golden; Alexander, Christine; Taneja, Sonia; Tirumalasetty, Sowmya; Chadalavada, Deepthi

2012-01-01

The first student Six Sigma team (activated under a QEP Process Sub-team) evaluated the course and curriculum approval process. The goal was to streamline the process and thereby shorten process cycle time and reduce confusion about how the process works. Members of this team developed flowcharts on how the process is supposed to work (by…

Impact of Radio Frequency Identification (RFID) on the Marine Corps’ Supply Process

DTIC Science & Technology

2006-09-01

Hypothetical Improvement Using a Real-Time Order Processing System Vice a Batch Order Processing System ................56 3. As-Is: The Current... Processing System Vice a Batch Order Processing System ................58 V. RESULTS ................................................69 A. SIMULATION...Time: Hypothetical Improvement Using a Real-Time Order Processing System Vice a Batch Order Processing System ................71 3. As-Is: The

Global-local processing relates to spatial and verbal processing: implications for sex differences in cognition.

PubMed

Pletzer, Belinda; Scheuringer, Andrea; Scherndl, Thomas

2017-09-05

Sex differences have been reported for a variety of cognitive tasks and related to the use of different cognitive processing styles in men and women. It was recently argued that these processing styles share some characteristics across tasks, i.e. male approaches are oriented towards holistic stimulus aspects and female approaches are oriented towards stimulus details. In that respect, sex-dependent cognitive processing styles share similarities with attentional global-local processing. A direct relationship between cognitive processing and global-local processing has however not been previously established. In the present study, 49 men and 44 women completed a Navon paradigm and a Kimchi Palmer task as well as a navigation task and a verbal fluency task with the goal to relate the global advantage (GA) effect as a measure of global processing to holistic processing styles in both tasks. Indeed participants with larger GA effects displayed more holistic processing during spatial navigation and phonemic fluency. However, the relationship to cognitive processing styles was modulated by the specific condition of the Navon paradigm, as well as the sex of participants. Thus, different types of global-local processing play different roles for cognitive processing in men and women.

21 CFR 113.83 - Establishing scheduled processes.

Code of Federal Regulations, 2012 CFR

2012-04-01

... competent processing authorities. If incubation tests are necessary for process confirmation, they shall... instituting the process. The incubation tests for confirmation of the scheduled processes should include the.... Complete records covering all aspects of the establishment of the process and associated incubation tests...

21 CFR 113.83 - Establishing scheduled processes.

Code of Federal Regulations, 2014 CFR

2014-04-01

... competent processing authorities. If incubation tests are necessary for process confirmation, they shall... instituting the process. The incubation tests for confirmation of the scheduled processes should include the.... Complete records covering all aspects of the establishment of the process and associated incubation tests...

21 CFR 113.83 - Establishing scheduled processes.

Code of Federal Regulations, 2013 CFR

2013-04-01

... competent processing authorities. If incubation tests are necessary for process confirmation, they shall... instituting the process. The incubation tests for confirmation of the scheduled processes should include the.... Complete records covering all aspects of the establishment of the process and associated incubation tests...

A mathematical study of a random process proposed as an atmospheric turbulence model

NASA Technical Reports Server (NTRS)

Sidwell, K.

1977-01-01

A random process is formed by the product of a local Gaussian process and a random amplitude process, and the sum of that product with an independent mean value process. The mathematical properties of the resulting process are developed, including the first and second order properties and the characteristic function of general order. An approximate method for the analysis of the response of linear dynamic systems to the process is developed. The transition properties of the process are also examined.

Standard services for the capture, processing, and distribution of packetized telemetry data

NASA Technical Reports Server (NTRS)

Stallings, William H.

1989-01-01

Standard functional services for the capture, processing, and distribution of packetized data are discussed with particular reference to the future implementation of packet processing systems, such as those for the Space Station Freedom. The major functions are listed under the following major categories: input processing, packet processing, and output processing. A functional block diagram of a packet data processing facility is presented, showing the distribution of the various processing functions as well as the primary data flow through the facility.

Assessment of hospital processes using a process mining technique: Outpatient process analysis at a tertiary hospital.

PubMed

Yoo, Sooyoung; Cho, Minsu; Kim, Eunhye; Kim, Seok; Sim, Yerim; Yoo, Donghyun; Hwang, Hee; Song, Minseok

2016-04-01

Many hospitals are increasing their efforts to improve processes because processes play an important role in enhancing work efficiency and reducing costs. However, to date, a quantitative tool has not been available to examine the before and after effects of processes and environmental changes, other than the use of indirect indicators, such as mortality rate and readmission rate. This study used process mining technology to analyze process changes based on changes in the hospital environment, such as the construction of a new building, and to measure the effects of environmental changes in terms of consultation wait time, time spent per task, and outpatient care processes. Using process mining technology, electronic health record (EHR) log data of outpatient care before and after constructing a new building were analyzed, and the effectiveness of the technology in terms of the process was evaluated. Using the process mining technique, we found that the total time spent in outpatient care did not increase significantly compared to that before the construction of a new building, considering that the number of outpatients increased, and the consultation wait time decreased. These results suggest that the operation of the outpatient clinic was effective after changes were implemented in the hospital environment. We further identified improvements in processes using the process mining technique, thereby demonstrating the usefulness of this technique for analyzing complex hospital processes at a low cost. This study confirmed the effectiveness of process mining technology at an actual hospital site. In future studies, the use of process mining technology will be expanded by applying this approach to a larger variety of process change situations. Copyright © 2016. Published by Elsevier Ireland Ltd.

Study of process variables associated with manufacturing hermetically-sealed nickel-cadmium cells

NASA Technical Reports Server (NTRS)

Miller, L.

1974-01-01

A two year study of the major process variables associated with the manufacturing process for sealed, nickel-cadmium, areospace cells is summarized. Effort was directed toward identifying the major process variables associated with a manufacturing process, experimentally assessing each variable's effect, and imposing the necessary changes (optimization) and controls for the critical process variables to improve results and uniformity. A critical process variable associated with the sintered nickel plaque manufacturing process was identified as the manual forming operation. Critical process variables identified with the positive electrode impregnation/polarization process were impregnation solution temperature, free acid content, vacuum impregnation, and sintered plaque strength. Positive and negative electrodes were identified as a major source of carbonate contamination in sealed cells.

Monitoring autocorrelated process: A geometric Brownian motion process approach

NASA Astrophysics Data System (ADS)

Li, Lee Siaw; Djauhari, Maman A.

2013-09-01

Autocorrelated process control is common in today's modern industrial process control practice. The current practice of autocorrelated process control is to eliminate the autocorrelation by using an appropriate model such as Box-Jenkins models or other models and then to conduct process control operation based on the residuals. In this paper we show that many time series are governed by a geometric Brownian motion (GBM) process. Therefore, in this case, by using the properties of a GBM process, we only need an appropriate transformation and model the transformed data to come up with the condition needs in traditional process control. An industrial example of cocoa powder production process in a Malaysian company will be presented and discussed to illustrate the advantages of the GBM approach.

Meta-control of combustion performance with a data mining approach

NASA Astrophysics Data System (ADS)

Song, Zhe

Large scale combustion process is complex and proposes challenges of optimizing its performance. Traditional approaches based on thermal dynamics have limitations on finding optimal operational regions due to time-shift nature of the process. Recent advances in information technology enable people collect large volumes of process data easily and continuously. The collected process data contains rich information about the process and, to some extent, represents a digital copy of the process over time. Although large volumes of data exist in industrial combustion processes, they are not fully utilized to the level where the process can be optimized. Data mining is an emerging science which finds patterns or models from large data sets. It has found many successful applications in business marketing, medical and manufacturing domains The focus of this dissertation is on applying data mining to industrial combustion processes, and ultimately optimizing the combustion performance. However the philosophy, methods and frameworks discussed in this research can also be applied to other industrial processes. Optimizing an industrial combustion process has two major challenges. One is the underlying process model changes over time and obtaining an accurate process model is nontrivial. The other is that a process model with high fidelity is usually highly nonlinear, solving the optimization problem needs efficient heuristics. This dissertation is set to solve these two major challenges. The major contribution of this 4-year research is the data-driven solution to optimize the combustion process, where process model or knowledge is identified based on the process data, then optimization is executed by evolutionary algorithms to search for optimal operating regions.

5 CFR 1653.13 - Processing legal processes.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 5 Administrative Personnel 3 2014-01-01 2014-01-01 false Processing legal processes. 1653.13 Section 1653.13 Administrative Personnel FEDERAL RETIREMENT THRIFT INVESTMENT BOARD COURT ORDERS AND LEGAL PROCESSES AFFECTING THRIFT SAVINGS PLAN ACCOUNTS Legal Process for the Enforcement of a Participant's Legal...

5 CFR 1653.13 - Processing legal processes.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 5 Administrative Personnel 3 2013-01-01 2013-01-01 false Processing legal processes. 1653.13 Section 1653.13 Administrative Personnel FEDERAL RETIREMENT THRIFT INVESTMENT BOARD COURT ORDERS AND LEGAL PROCESSES AFFECTING THRIFT SAVINGS PLAN ACCOUNTS Legal Process for the Enforcement of a Participant's Legal...

A Search Algorithm for Generating Alternative Process Plans in Flexible Manufacturing System

NASA Astrophysics Data System (ADS)

Tehrani, Hossein; Sugimura, Nobuhiro; Tanimizu, Yoshitaka; Iwamura, Koji

Capabilities and complexity of manufacturing systems are increasing and striving for an integrated manufacturing environment. Availability of alternative process plans is a key factor for integration of design, process planning and scheduling. This paper describes an algorithm for generation of alternative process plans by extending the existing framework of the process plan networks. A class diagram is introduced for generating process plans and process plan networks from the viewpoint of the integrated process planning and scheduling systems. An incomplete search algorithm is developed for generating and searching the process plan networks. The benefit of this algorithm is that the whole process plan network does not have to be generated before the search algorithm starts. This algorithm is applicable to large and enormous process plan networks and also to search wide areas of the network based on the user requirement. The algorithm can generate alternative process plans and to select a suitable one based on the objective functions.

PyMS: a Python toolkit for processing of gas chromatography-mass spectrometry (GC-MS) data. Application and comparative study of selected tools.

PubMed

O'Callaghan, Sean; De Souza, David P; Isaac, Andrew; Wang, Qiao; Hodkinson, Luke; Olshansky, Moshe; Erwin, Tim; Appelbe, Bill; Tull, Dedreia L; Roessner, Ute; Bacic, Antony; McConville, Malcolm J; Likić, Vladimir A

2012-05-30

Gas chromatography-mass spectrometry (GC-MS) is a technique frequently used in targeted and non-targeted measurements of metabolites. Most existing software tools for processing of raw instrument GC-MS data tightly integrate data processing methods with graphical user interface facilitating interactive data processing. While interactive processing remains critically important in GC-MS applications, high-throughput studies increasingly dictate the need for command line tools, suitable for scripting of high-throughput, customized processing pipelines. PyMS comprises a library of functions for processing of instrument GC-MS data developed in Python. PyMS currently provides a complete set of GC-MS processing functions, including reading of standard data formats (ANDI- MS/NetCDF and JCAMP-DX), noise smoothing, baseline correction, peak detection, peak deconvolution, peak integration, and peak alignment by dynamic programming. A novel common ion single quantitation algorithm allows automated, accurate quantitation of GC-MS electron impact (EI) fragmentation spectra when a large number of experiments are being analyzed. PyMS implements parallel processing for by-row and by-column data processing tasks based on Message Passing Interface (MPI), allowing processing to scale on multiple CPUs in distributed computing environments. A set of specifically designed experiments was performed in-house and used to comparatively evaluate the performance of PyMS and three widely used software packages for GC-MS data processing (AMDIS, AnalyzerPro, and XCMS). PyMS is a novel software package for the processing of raw GC-MS data, particularly suitable for scripting of customized processing pipelines and for data processing in batch mode. PyMS provides limited graphical capabilities and can be used both for routine data processing and interactive/exploratory data analysis. In real-life GC-MS data processing scenarios PyMS performs as well or better than leading software packages. We demonstrate data processing scenarios simple to implement in PyMS, yet difficult to achieve with many conventional GC-MS data processing software. Automated sample processing and quantitation with PyMS can provide substantial time savings compared to more traditional interactive software systems that tightly integrate data processing with the graphical user interface.

Processing mode during repetitive thinking in socially anxious individuals: evidence for a maladaptive experiential mode.

PubMed

Wong, Quincy J J; Moulds, Michelle L

2012-12-01

Evidence from the depression literature suggests that an analytical processing mode adopted during repetitive thinking leads to maladaptive outcomes relative to an experiential processing mode. To date, in socially anxious individuals, the impact of processing mode during repetitive thinking related to an actual social-evaluative situation has not been investigated. We thus tested whether an analytical processing mode would be maladaptive relative to an experiential processing mode during anticipatory processing and post-event rumination. High and low socially anxious participants were induced to engage in either an analytical or experiential processing mode during: (a) anticipatory processing before performing a speech (Experiment 1; N = 94), or (b) post-event rumination after performing a speech (Experiment 2; N = 74). Mood, cognition, and behavioural measures were employed to examine the effects of processing mode. For high socially anxious participants, the modes had a similar effect on self-reported anxiety during both anticipatory processing and post-event rumination. Unexpectedly, relative to the analytical mode, the experiential mode led to stronger high standard and conditional beliefs during anticipatory processing, and stronger unconditional beliefs during post-event rumination. These experiments are the first to investigate processing mode during anticipatory processing and post-event rumination. Hence, these results are novel and will need to be replicated. These findings suggest that an experiential processing mode is maladaptive relative to an analytical processing mode during repetitive thinking characteristic of socially anxious individuals. Copyright © 2012 Elsevier Ltd. All rights reserved.

Using process elicitation and validation to understand and improve chemotherapy ordering and delivery.

PubMed

Mertens, Wilson C; Christov, Stefan C; Avrunin, George S; Clarke, Lori A; Osterweil, Leon J; Cassells, Lucinda J; Marquard, Jenna L

2012-11-01

Chemotherapy ordering and administration, in which errors have potentially severe consequences, was quantitatively and qualitatively evaluated by employing process formalism (or formal process definition), a technique derived from software engineering, to elicit and rigorously describe the process, after which validation techniques were applied to confirm the accuracy of the described process. The chemotherapy ordering and administration process, including exceptional situations and individuals' recognition of and responses to those situations, was elicited through informal, unstructured interviews with members of an interdisciplinary team. The process description (or process definition), written in a notation developed for software quality assessment purposes, guided process validation (which consisted of direct observations and semistructured interviews to confirm the elicited details for the treatment plan portion of the process). The overall process definition yielded 467 steps; 207 steps (44%) were dedicated to handling 59 exceptional situations. Validation yielded 82 unique process events (35 new expected but not yet described steps, 16 new exceptional situations, and 31 new steps in response to exceptional situations). Process participants actively altered the process as ambiguities and conflicts were discovered by the elicitation and validation components of the study. Chemotherapy error rates declined significantly during and after the project, which was conducted from October 2007 through August 2008. Each elicitation method and the subsequent validation discussions contributed uniquely to understanding the chemotherapy treatment plan review process, supporting rapid adoption of changes, improved communication regarding the process, and ensuing error reduction.

Modeling interdependencies between business and communication processes in hospitals.

PubMed

Brigl, Birgit; Wendt, Thomas; Winter, Alfred

2003-01-01

The optimization and redesign of business processes in hospitals is an important challenge for the hospital information management who has to design and implement a suitable HIS architecture. Nevertheless, there are no tools available specializing in modeling information-driven business processes and the consequences on the communication between information processing, tools. Therefore, we will present an approach which facilitates the representation and analysis of business processes and resulting communication processes between application components and their interdependencies. This approach aims not only to visualize those processes, but to also to evaluate if there are weaknesses concerning the information processing infrastructure which hinder the smooth implementation of the business processes.

Life cycle analysis within pharmaceutical process optimization and intensification: case study of active pharmaceutical ingredient production.

PubMed

Ott, Denise; Kralisch, Dana; Denčić, Ivana; Hessel, Volker; Laribi, Yosra; Perrichon, Philippe D; Berguerand, Charline; Kiwi-Minsker, Lioubov; Loeb, Patrick

2014-12-01

As the demand for new drugs is rising, the pharmaceutical industry faces the quest of shortening development time, and thus, reducing the time to market. Environmental aspects typically still play a minor role within the early phase of process development. Nevertheless, it is highly promising to rethink, redesign, and optimize process strategies as early as possible in active pharmaceutical ingredient (API) process development, rather than later at the stage of already established processes. The study presented herein deals with a holistic life-cycle-based process optimization and intensification of a pharmaceutical production process targeting a low-volume, high-value API. Striving for process intensification by transfer from batch to continuous processing, as well as an alternative catalytic system, different process options are evaluated with regard to their environmental impact to identify bottlenecks and improvement potentials for further process development activities. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

SOI-CMOS Process for Monolithic, Radiation-Tolerant, Science-Grade Imagers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, George; Lee, Adam

In Phase I, Voxtel worked with Jazz and Sandia to document and simulate the processes necessary to implement a DH-BSI SOI CMOS imaging process. The development is based upon mature SOI CMOS process at both fabs, with the addition of only a few custom processing steps for integration and electrical interconnection of the fully-depleted photodetectors. In Phase I, Voxtel also characterized the Sandia process, including the CMOS7 design rules, and we developed the outline of a process option that included a “BOX etch”, that will permit a “detector in handle” SOI CMOS process to be developed The process flows weremore » developed in cooperation with both Jazz and Sandia process engineers, along with detailed TCAD modeling and testing of the photodiode array architectures. In addition, Voxtel tested the radiation performance of the Jazz’s CA18HJ process, using standard and circular-enclosed transistors.« less

Face to face with emotion: holistic face processing is modulated by emotional state.

PubMed

Curby, Kim M; Johnson, Kareem J; Tyson, Alyssa

2012-01-01

Negative emotions are linked with a local, rather than global, visual processing style, which may preferentially facilitate feature-based, relative to holistic, processing mechanisms. Because faces are typically processed holistically, and because social contexts are prime elicitors of emotions, we examined whether negative emotions decrease holistic processing of faces. We induced positive, negative, or neutral emotions via film clips and measured holistic processing before and after the induction: participants made judgements about cued parts of chimeric faces, and holistic processing was indexed by the interference caused by task-irrelevant face parts. Emotional state significantly modulated face-processing style, with the negative emotion induction leading to decreased holistic processing. Furthermore, self-reported change in emotional state correlated with changes in holistic processing. These results contrast with general assumptions that holistic processing of faces is automatic and immune to outside influences, and they illustrate emotion's power to modulate socially relevant aspects of visual perception.

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2013 CFR

2013-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2012 CFR

2012-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

20 CFR 405.725 - Effect of expedited appeals process agreement.

Code of Federal Regulations, 2010 CFR

2010-04-01

... PROCESS FOR ADJUDICATING INITIAL DISABILITY CLAIMS Expedited Appeals Process for Constitutional Issues § 405.725 Effect of expedited appeals process agreement. After an expedited appeals process agreement is... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Effect of expedited appeals process agreement...

Common and distinct networks for self-referential and social stimulus processing in the human brain.

PubMed

Herold, Dorrit; Spengler, Stephanie; Sajonz, Bastian; Usnich, Tatiana; Bermpohl, Felix

2016-09-01

Self-referential processing is a complex cognitive function, involving a set of implicit and explicit processes, complicating investigation of its distinct neural signature. The present study explores the functional overlap and dissociability of self-referential and social stimulus processing. We combined an established paradigm for explicit self-referential processing with an implicit social stimulus processing paradigm in one fMRI experiment to determine the neural effects of self-relatedness and social processing within one study. Overlapping activations were found in the orbitofrontal cortex and in the intermediate part of the precuneus. Stimuli judged as self-referential specifically activated the posterior cingulate cortex, the ventral medial prefrontal cortex, extending into anterior cingulate cortex and orbitofrontal cortex, the dorsal medial prefrontal cortex, the ventral and dorsal lateral prefrontal cortex, the left inferior temporal gyrus, and occipital cortex. Social processing specifically involved the posterior precuneus and bilateral temporo-parietal junction. Taken together, our data show, not only, first, common networks for both processes in the medial prefrontal and the medial parietal cortex, but also, second, functional differentiations for self-referential processing versus social processing: an anterior-posterior gradient for social processing and self-referential processing within the medial parietal cortex and specific activations for self-referential processing in the medial and lateral prefrontal cortex and for social processing in the temporo-parietal junction.

Using Unified Modelling Language (UML) as a process-modelling technique for clinical-research process improvement.

PubMed

Kumarapeli, P; De Lusignan, S; Ellis, T; Jones, B

2007-03-01

The Primary Care Data Quality programme (PCDQ) is a quality-improvement programme which processes routinely collected general practice computer data. Patient data collected from a wide range of different brands of clinical computer systems are aggregated, processed, and fed back to practices in an educational context to improve the quality of care. Process modelling is a well-established approach used to gain understanding and systematic appraisal, and identify areas of improvement of a business process. Unified modelling language (UML) is a general purpose modelling technique used for this purpose. We used UML to appraise the PCDQ process to see if the efficiency and predictability of the process could be improved. Activity analysis and thinking-aloud sessions were used to collect data to generate UML diagrams. The UML model highlighted the sequential nature of the current process as a barrier for efficiency gains. It also identified the uneven distribution of process controls, lack of symmetric communication channels, critical dependencies among processing stages, and failure to implement all the lessons learned in the piloting phase. It also suggested that improved structured reporting at each stage - especially from the pilot phase, parallel processing of data and correctly positioned process controls - should improve the efficiency and predictability of research projects. Process modelling provided a rational basis for the critical appraisal of a clinical data processing system; its potential maybe underutilized within health care.

Use of Analogies in the Study of Diffusion

ERIC Educational Resources Information Center

Letic, Milorad

2014-01-01

Emergent processes, such as diffusion, are considered more difficult to understand than direct processes. In physiology, most processes are presented as direct processes, so emergent processes, when encountered, are even more difficult to understand. It has been suggested that, when studying diffusion, misconceptions about random processes are the…

Is Analytic Information Processing a Feature of Expertise in Medicine?

ERIC Educational Resources Information Center

McLaughlin, Kevin; Rikers, Remy M.; Schmidt, Henk G.

2008-01-01

Diagnosing begins by generating an initial diagnostic hypothesis by automatic information processing. Information processing may stop here if the hypothesis is accepted, or analytical processing may be used to refine the hypothesis. This description portrays analytic processing as an optional extra in information processing, leading us to…

5 CFR 582.305 - Honoring legal process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 5 Administrative Personnel 1 2014-01-01 2014-01-01 false Honoring legal process. 582.305 Section... GARNISHMENT OF FEDERAL EMPLOYEES' PAY Compliance With Legal Process § 582.305 Honoring legal process. (a) The agency shall comply with legal process, except where the process cannot be complied with because: (1) It...

5 CFR 582.305 - Honoring legal process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false Honoring legal process. 582.305 Section... GARNISHMENT OF FEDERAL EMPLOYEES' PAY Compliance With Legal Process § 582.305 Honoring legal process. (a) The agency shall comply with legal process, except where the process cannot be complied with because: (1) It...

5 CFR 581.305 - Honoring legal process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 5 Administrative Personnel 1 2014-01-01 2014-01-01 false Honoring legal process. 581.305 Section... GARNISHMENT ORDERS FOR CHILD SUPPORT AND/OR ALIMONY Compliance With Process § 581.305 Honoring legal process. (a) The governmental entity shall comply with legal process, except where the process cannot be...

5 CFR 581.305 - Honoring legal process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Honoring legal process. 581.305 Section... GARNISHMENT ORDERS FOR CHILD SUPPORT AND/OR ALIMONY Compliance With Process § 581.305 Honoring legal process. (a) The governmental entity shall comply with legal process, except where the process cannot be...

5 CFR 582.305 - Honoring legal process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Honoring legal process. 582.305 Section... GARNISHMENT OF FEDERAL EMPLOYEES' PAY Compliance With Legal Process § 582.305 Honoring legal process. (a) The agency shall comply with legal process, except where the process cannot be complied with because: (1) It...

5 CFR 581.305 - Honoring legal process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false Honoring legal process. 581.305 Section... GARNISHMENT ORDERS FOR CHILD SUPPORT AND/OR ALIMONY Compliance With Process § 581.305 Honoring legal process. (a) The governmental entity shall comply with legal process, except where the process cannot be...

Articulating the Resources for Business Process Analysis and Design

ERIC Educational Resources Information Center

Jin, Yulong

2012-01-01

Effective process analysis and modeling are important phases of the business process management lifecycle. When many activities and multiple resources are involved, it is very difficult to build a correct business process specification. This dissertation provides a resource perspective of business processes. It aims at a better process analysis…

An Integrated Model of Emotion Processes and Cognition in Social Information Processing.

ERIC Educational Resources Information Center

Lemerise, Elizabeth A.; Arsenio, William F.

2000-01-01

Interprets literature on contributions of social cognitive and emotion processes to children's social competence in the context of an integrated model of emotion processes and cognition in social information processing. Provides neurophysiological and functional evidence for the centrality of emotion processes in personal-social decision making.…

Data Processing and First Products from the Hyperspectral Imager for the Coastal Ocean (HICO) on the International Space Station

DTIC Science & Technology

2010-04-01

NRL Stennis Space Center (NRL-SSC) for further processing using the NRL SSC Automated Processing System (APS). APS was developed for processing...have not previously developed automated processing for 73 hyperspectral ocean color data. The hyperspectral processing branch includes several

DISCRETE COMPOUND POISSON PROCESSES AND TABLES OF THE GEOMETRIC POISSON DISTRIBUTION.

DTIC Science & Technology

A concise summary of the salient properties of discrete Poisson processes , with emphasis on comparing the geometric and logarithmic Poisson processes . The...the geometric Poisson process are given for 176 sets of parameter values. New discrete compound Poisson processes are also introduced. These...processes have properties that are particularly relevant when the summation of several different Poisson processes is to be analyzed. This study provides the

Management of processes of electrochemical dimensional processing

NASA Astrophysics Data System (ADS)

Akhmetov, I. D.; Zakirova, A. R.; Sadykov, Z. B.

2017-09-01

In different industries a lot high-precision parts are produced from hard-processed scarce materials. Forming such details can only be acting during non-contact processing, or a minimum of effort, and doable by the use, for example, of electro-chemical processing. At the present stage of development of metal working processes are important management issues electrochemical machining and its automation. This article provides some indicators and factors of electrochemical machining process.

The Hyperspectral Imager for the Coastal Ocean (HICO): Sensor and Data Processing Overview

DTIC Science & Technology

2010-01-20

backscattering coefficients, and others. Several of these software modules will be developed within the Automated Processing System (APS), a data... Automated Processing System (APS) NRL developed APS, which processes satellite data into ocean color data products. APS is a collection of methods...used for ocean color processing which provide the tools for the automated processing of satellite imagery [1]. These tools are in the process of

[Study on culture and philosophy of processing of traditional Chinese medicines].

PubMed

Yang, Ming; Zhang, Ding-Kun; Zhong, Ling-Yun; Wang, Fang

2013-07-01

According to cultural views and philosophical thoughts, this paper studies the cultural origin, thinking modes, core principles, general regulation and methods of processing, backtracks processing's culture and history which contains generation and deduction process, experienced and promoting process, and core value, summarizes processing's basic principles which are directed by holistic, objective, dynamic, balanced and appropriate thoughts; so as to propagate cultural characteristic and philosophical wisdom of traditional Chinese medicine processing, to promote inheritance and development of processing and to ensure the maximum therapeutic value of Chinese medical clinical.

Containerless automated processing of intermetallic compounds and composites

NASA Technical Reports Server (NTRS)

Johnson, D. R.; Joslin, S. M.; Reviere, R. D.; Oliver, B. F.; Noebe, R. D.

1993-01-01

An automated containerless processing system has been developed to directionally solidify high temperature materials, intermetallic compounds, and intermetallic/metallic composites. The system incorporates a wide range of ultra-high purity chemical processing conditions. The utilization of image processing for automated control negates the need for temperature measurements for process control. The list of recent systems that have been processed includes Cr, Mo, Mn, Nb, Ni, Ti, V, and Zr containing aluminides. Possible uses of the system, process control approaches, and properties and structures of recently processed intermetallics are reviewed.

A continuous process for the development of Kodak Aerochrome Infrared Film 2443 as a negative

NASA Astrophysics Data System (ADS)

Klimes, D.; Ross, D. I.

1993-02-01

A process for the continuous dry-to-dry development of Kodak Aerochrome Infrared Film 2443 as a negative (CIR-neg) is described. The process is well suited for production processing of long film lengths. Chemicals from three commercial film processes are used with modifications. Sensitometric procedures are recommended for the monitoring of processing quality control. Sensitometric data and operational aerial exposures indicate that films developed in this process have approximately the same effective aerial film speed as films processed in the reversal process recommended by the manufacturer (Kodak EA-5). The CIR-neg process is useful when aerial photography is acquired for resources management applications which require print reproductions. Originals can be readily reproduced using conventional production equipment (electronic dodging) in black and white or color (color compensation).

Antibiotics with anaerobic ammonium oxidation in urban wastewater treatment

NASA Astrophysics Data System (ADS)

Zhou, Ruipeng; Yang, Yuanming

2017-05-01

Biofilter process is based on biological oxidation process on the introduction of fast water filter design ideas generated by an integrated filtration, adsorption and biological role of aerobic wastewater treatment process various purification processes. By engineering example, we show that the process is an ideal sewage and industrial wastewater treatment process of low concentration. Anaerobic ammonia oxidation process because of its advantage of the high efficiency and low consumption, wastewater biological denitrification field has broad application prospects. The process in practical wastewater treatment at home and abroad has become a hot spot. In this paper, anammox bacteria habitats and species diversity, and anaerobic ammonium oxidation process in the form of diversity, and one and split the process operating conditions are compared, focusing on a review of the anammox process technology various types of wastewater laboratory research and engineering applications, including general water quality and pressure filtrate sludge digestion, landfill leachate, aquaculture wastewater, monosodium glutamate wastewater, wastewater, sewage, fecal sewage, waste water salinity wastewater characteristics, research progress and application of the obstacles. Finally, we summarize the anaerobic ammonium oxidation process potential problems during the processing of the actual waste water, and proposed future research focus on in-depth study of water quality anammox obstacle factor and its regulatory policy, and vigorously develop on this basis, and combined process optimization.

Understanding scaling through history-dependent processes with collapsing sample space.

PubMed

Corominas-Murtra, Bernat; Hanel, Rudolf; Thurner, Stefan

2015-04-28

History-dependent processes are ubiquitous in natural and social systems. Many such stochastic processes, especially those that are associated with complex systems, become more constrained as they unfold, meaning that their sample space, or their set of possible outcomes, reduces as they age. We demonstrate that these sample-space-reducing (SSR) processes necessarily lead to Zipf's law in the rank distributions of their outcomes. We show that by adding noise to SSR processes the corresponding rank distributions remain exact power laws, p(x) ~ x(-λ), where the exponent directly corresponds to the mixing ratio of the SSR process and noise. This allows us to give a precise meaning to the scaling exponent in terms of the degree to which a given process reduces its sample space as it unfolds. Noisy SSR processes further allow us to explain a wide range of scaling exponents in frequency distributions ranging from α = 2 to ∞. We discuss several applications showing how SSR processes can be used to understand Zipf's law in word frequencies, and how they are related to diffusion processes in directed networks, or aging processes such as in fragmentation processes. SSR processes provide a new alternative to understand the origin of scaling in complex systems without the recourse to multiplicative, preferential, or self-organized critical processes.

Effects of Processing Parameters on the Forming Quality of C-Shaped Thermosetting Composite Laminates in Hot Diaphragm Forming Process

NASA Astrophysics Data System (ADS)

Bian, X. X.; Gu, Y. Z.; Sun, J.; Li, M.; Liu, W. P.; Zhang, Z. G.

2013-10-01

In this study, the effects of processing temperature and vacuum applying rate on the forming quality of C-shaped carbon fiber reinforced epoxy resin matrix composite laminates during hot diaphragm forming process were investigated. C-shaped prepreg preforms were produced using a home-made hot diaphragm forming equipment. The thickness variations of the preforms and the manufacturing defects after diaphragm forming process, including fiber wrinkling and voids, were evaluated to understand the forming mechanism. Furthermore, both interlaminar slipping friction and compaction behavior of the prepreg stacks were experimentally analyzed for showing the importance of the processing parameters. In addition, autoclave processing was used to cure the C-shaped preforms to investigate the changes of the defects before and after cure process. The results show that the C-shaped prepreg preforms with good forming quality can be achieved through increasing processing temperature and reducing vacuum applying rate, which obviously promote prepreg interlaminar slipping process. The process temperature and forming rate in hot diaphragm forming process strongly influence prepreg interply frictional force, and the maximum interlaminar frictional force can be taken as a key parameter for processing parameter optimization. Autoclave process is effective in eliminating voids in the preforms and can alleviate fiber wrinkles to a certain extent.

Assessment of Advanced Coal Gasification Processes

NASA Technical Reports Server (NTRS)

McCarthy, John; Ferrall, Joseph; Charng, Thomas; Houseman, John

1981-01-01

This report represents a technical assessment of the following advanced coal gasification processes: AVCO High Throughput Gasification (HTG) Process; Bell Single-Stage High Mass Flux (HMF) Process; Cities Service/Rockwell (CS/R) Hydrogasification Process; Exxon Catalytic Coal Gasification (CCG) Process. Each process is evaluated for its potential to produce SNG from a bituminous coal. In addition to identifying the new technology these processes represent, key similarities/differences, strengths/weaknesses, and potential improvements to each process are identified. The AVCO HTG and the Bell HMF gasifiers share similarities with respect to: short residence time (SRT), high throughput rate, slagging and syngas as the initial raw product gas. The CS/R Hydrogasifier is also SRT but is non-slagging and produces a raw gas high in methane content. The Exxon CCG gasifier is a long residence time, catalytic, fluidbed reactor producing all of the raw product methane in the gasifier. The report makes the following assessments: 1) while each process has significant potential as coal gasifiers, the CS/R and Exxon processes are better suited for SNG production; 2) the Exxon process is the closest to a commercial level for near-term SNG production; and 3) the SRT processes require significant development including scale-up and turndown demonstration, char processing and/or utilization demonstration, and reactor control and safety features development.

Integrated Process Modeling-A Process Validation Life Cycle Companion.

PubMed

Zahel, Thomas; Hauer, Stefan; Mueller, Eric M; Murphy, Patrick; Abad, Sandra; Vasilieva, Elena; Maurer, Daniel; Brocard, Cécile; Reinisch, Daniela; Sagmeister, Patrick; Herwig, Christoph

2017-10-17

During the regulatory requested process validation of pharmaceutical manufacturing processes, companies aim to identify, control, and continuously monitor process variation and its impact on critical quality attributes (CQAs) of the final product. It is difficult to directly connect the impact of single process parameters (PPs) to final product CQAs, especially in biopharmaceutical process development and production, where multiple unit operations are stacked together and interact with each other. Therefore, we want to present the application of Monte Carlo (MC) simulation using an integrated process model (IPM) that enables estimation of process capability even in early stages of process validation. Once the IPM is established, its capability in risk and criticality assessment is furthermore demonstrated. IPMs can be used to enable holistic production control strategies that take interactions of process parameters of multiple unit operations into account. Moreover, IPMs can be trained with development data, refined with qualification runs, and maintained with routine manufacturing data which underlines the lifecycle concept. These applications will be shown by means of a process characterization study recently conducted at a world-leading contract manufacturing organization (CMO). The new IPM methodology therefore allows anticipation of out of specification (OOS) events, identify critical process parameters, and take risk-based decisions on counteractions that increase process robustness and decrease the likelihood of OOS events.

Effects of rigor status during high-pressure processing on the physical qualities of farm-raised abalone (Haliotis rufescens).

PubMed

Hughes, Brianna H; Greenberg, Neil J; Yang, Tom C; Skonberg, Denise I

2015-01-01

High-pressure processing (HPP) is used to increase meat safety and shelf-life, with conflicting quality effects depending on rigor status during HPP. In the seafood industry, HPP is used to shuck and pasteurize oysters, but its use on abalones has only been minimally evaluated and the effect of rigor status during HPP on abalone quality has not been reported. Farm-raised abalones (Haliotis rufescens) were divided into 12 HPP treatments and 1 unprocessed control treatment. Treatments were processed pre-rigor or post-rigor at 2 pressures (100 and 300 MPa) and 3 processing times (1, 3, and 5 min). The control was analyzed post-rigor. Uniform plugs were cut from adductor and foot meat for texture profile analysis, shear force, and color analysis. Subsamples were used for scanning electron microscopy of muscle ultrastructure. Texture profile analysis revealed that post-rigor processed abalone was significantly (P < 0.05) less firm and chewy than pre-rigor processed irrespective of muscle type, processing time, or pressure. L values increased with pressure to 68.9 at 300 MPa for pre-rigor processed foot, 73.8 for post-rigor processed foot, 90.9 for pre-rigor processed adductor, and 89.0 for post-rigor processed adductor. Scanning electron microscopy images showed fraying of collagen fibers in processed adductor, but did not show pressure-induced compaction of the foot myofibrils. Post-rigor processed abalone meat was more tender than pre-rigor processed meat, and post-rigor processed foot meat was lighter in color than pre-rigor processed foot meat, suggesting that waiting for rigor to resolve prior to processing abalones may improve consumer perceptions of quality and market value. © 2014 Institute of Food Technologists®

PROCESSING ALTERNATIVES FOR DESTRUCTION OF TETRAPHENYLBORATE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D; Thomas Peters, T; Samuel Fink, S

Two processes were chosen in the 1980's at the Savannah River Site (SRS) to decontaminate the soluble High Level Waste (HLW). The In Tank Precipitation (ITP) process (1,2) was developed at SRS for the removal of radioactive cesium and actinides from the soluble HLW. Sodium tetraphenylborate was added to the waste to precipitate cesium and monosodium titanate (MST) was added to adsorb actinides, primarily uranium and plutonium. Two products of this process were a low activity waste stream and a concentrated organic stream containing cesium tetraphenylborate and actinides adsorbed on monosodium titanate (MST). A copper catalyzed acid hydrolysis process wasmore » built to process (3, 4) the Tank 48H cesium tetraphenylborate waste in the SRS's Defense Waste Processing Facility (DWPF). Operation of the DWPF would have resulted in the production of benzene for incineration in SRS's Consolidated Incineration Facility. This process was abandoned together with the ITP process in 1998 due to high benzene in ITP caused by decomposition of excess sodium tetraphenylborate. Processing in ITP resulted in the production of approximately 1.0 million liters of HLW. SRS has chosen a solvent extraction process combined with adsorption of the actinides to decontaminate the soluble HLW stream (5). However, the waste in Tank 48H is incompatible with existing waste processing facilities. As a result, a processing facility is needed to disposition the HLW in Tank 48H. This paper will describe the process for searching for processing options by SRS task teams for the disposition of the waste in Tank 48H. In addition, attempts to develop a caustic hydrolysis process for in tank destruction of tetraphenylborate will be presented. Lastly, the development of both a caustic and acidic copper catalyzed peroxide oxidation process will be discussed.« less

Manufacturing Process Selection of Composite Bicycle’s Crank Arm using Analytical Hierarchy Process (AHP)

NASA Astrophysics Data System (ADS)

Luqman, M.; Rosli, M. U.; Khor, C. Y.; Zambree, Shayfull; Jahidi, H.

2018-03-01

Crank arm is one of the important parts in a bicycle that is an expensive product due to the high cost of material and production process. This research is aimed to investigate the potential type of manufacturing process to fabricate composite bicycle crank arm and to describe an approach based on analytical hierarchy process (AHP) that assists decision makers or manufacturing engineers in determining the most suitable process to be employed in manufacturing of composite bicycle crank arm at the early stage of the product development process to reduce the production cost. There are four types of processes were considered, namely resin transfer molding (RTM), compression molding (CM), vacuum bag molding and filament winding (FW). The analysis ranks these four types of process for its suitability in the manufacturing of bicycle crank arm based on five main selection factors and 10 sub factors. Determining the right manufacturing process was performed based on AHP process steps. Consistency test was performed to make sure the judgements are consistent during the comparison. The results indicated that the compression molding was the most appropriate manufacturing process because it has the highest value (33.6%) among the other manufacturing processes.

A System-Oriented Approach for the Optimal Control of Process Chains under Stochastic Influences

NASA Astrophysics Data System (ADS)

Senn, Melanie; Schäfer, Julian; Pollak, Jürgen; Link, Norbert

2011-09-01

Process chains in manufacturing consist of multiple connected processes in terms of dynamic systems. The properties of a product passing through such a process chain are influenced by the transformation of each single process. There exist various methods for the control of individual processes, such as classical state controllers from cybernetics or function mapping approaches realized by statistical learning. These controllers ensure that a desired state is obtained at process end despite of variations in the input and disturbances. The interactions between the single processes are thereby neglected, but play an important role in the optimization of the entire process chain. We divide the overall optimization into two phases: (1) the solution of the optimization problem by Dynamic Programming to find the optimal control variable values for each process for any encountered end state of its predecessor and (2) the application of the optimal control variables at runtime for the detected initial process state. The optimization problem is solved by selecting adequate control variables for each process in the chain backwards based on predefined quality requirements for the final product. For the demonstration of the proposed concept, we have chosen a process chain from sheet metal manufacturing with simplified transformation functions.

Quantitative analysis of geomorphic processes using satellite image data at different scales

NASA Technical Reports Server (NTRS)

Williams, R. S., Jr.

1985-01-01

When aerial and satellite photographs and images are used in the quantitative analysis of geomorphic processes, either through direct observation of active processes or by analysis of landforms resulting from inferred active or dormant processes, a number of limitations in the use of such data must be considered. Active geomorphic processes work at different scales and rates. Therefore, the capability of imaging an active or dormant process depends primarily on the scale of the process and the spatial-resolution characteristic of the imaging system. Scale is an important factor in recording continuous and discontinuous active geomorphic processes, because what is not recorded will not be considered or even suspected in the analysis of orbital images. If the geomorphic process of landform change caused by the process is less than 200 m in x to y dimension, then it will not be recorded. Although the scale factor is critical, in the recording of discontinuous active geomorphic processes, the repeat interval of orbital-image acquisition of a planetary surface also is a consideration in order to capture a recurring short-lived geomorphic process or to record changes caused by either a continuous or a discontinuous geomorphic process.

Remote Sensing Image Quality Assessment Experiment with Post-Processing

NASA Astrophysics Data System (ADS)

Jiang, W.; Chen, S.; Wang, X.; Huang, Q.; Shi, H.; Man, Y.

2018-04-01

This paper briefly describes the post-processing influence assessment experiment, the experiment includes three steps: the physical simulation, image processing, and image quality assessment. The physical simulation models sampled imaging system in laboratory, the imaging system parameters are tested, the digital image serving as image processing input are produced by this imaging system with the same imaging system parameters. The gathered optical sampled images with the tested imaging parameters are processed by 3 digital image processes, including calibration pre-processing, lossy compression with different compression ratio and image post-processing with different core. Image quality assessment method used is just noticeable difference (JND) subject assessment based on ISO20462, through subject assessment of the gathered and processing images, the influence of different imaging parameters and post-processing to image quality can be found. The six JND subject assessment experimental data can be validated each other. Main conclusions include: image post-processing can improve image quality; image post-processing can improve image quality even with lossy compression, image quality with higher compression ratio improves less than lower ratio; with our image post-processing method, image quality is better, when camera MTF being within a small range.

Microstructure and Texture of Al-2.5wt.%Mg Processed by Combining Accumulative Roll Bonding and Conventional Rolling

NASA Astrophysics Data System (ADS)

Gatti, J. R.; Bhattacharjee, P. P.

2014-12-01

Evolution of microstructure and texture during severe deformation and annealing was studied in Al-2.5%Mg alloy processed by two different routes, namely, monotonic Accumulative Roll Bonding (ARB) and a hybrid route combining ARB and conventional rolling (CR). For this purpose Al-2.5%Mg sheets were subjected to 5 cycles of monotonic ARB (equivalent strain (ɛeq) = 4.0) processing while in the hybrid route (ARB + CR) 3 cycle ARB-processed sheets were further deformed by conventional rolling to 75% reduction in thickness (ɛeq = 4.0). Although formation of ultrafine structure was observed in the two processing routes, the monotonic ARB—processed material showed finer microstructure but weak texture as compared to the ARB + CR—processed material. After complete recrystallization, the ARB + CR-processed material showed weak cube texture ({001}<100>) but the cube component was almost negligible in the monotonic ARB-processed material-processed material. However, the ND-rotated cube components were stronger in the monotonic ARB-processed material-processed material. The observed differences in the microstructure and texture evolution during deformation and annealing could be explained by the characteristic differences of the two processing routes.

Process Materialization Using Templates and Rules to Design Flexible Process Models

NASA Astrophysics Data System (ADS)

Kumar, Akhil; Yao, Wen

The main idea in this paper is to show how flexible processes can be designed by combining generic process templates and business rules. We instantiate a process by applying rules to specific case data, and running a materialization algorithm. The customized process instance is then executed in an existing workflow engine. We present an architecture and also give an algorithm for process materialization. The rules are written in a logic-based language like Prolog. Our focus is on capturing deeper process knowledge and achieving a holistic approach to robust process design that encompasses control flow, resources and data, as well as makes it easier to accommodate changes to business policy.

HMI conventions for process control graphics.

PubMed

Pikaar, Ruud N

2012-01-01

Process operators supervise and control complex processes. To enable the operator to do an adequate job, instrumentation and process control engineers need to address several related topics, such as console design, information design, navigation, and alarm management. In process control upgrade projects, usually a 1:1 conversion of existing graphics is proposed. This paper suggests another approach, efficiently leading to a reduced number of new powerful process graphics, supported by a permanent process overview displays. In addition a road map for structuring content (process information) and conventions for the presentation of objects, symbols, and so on, has been developed. The impact of the human factors engineering approach on process control upgrade projects is illustrated by several cases.

A novel processed food classification system applied to Australian food composition databases.

PubMed

O'Halloran, S A; Lacy, K E; Grimes, C A; Woods, J; Campbell, K J; Nowson, C A

2017-08-01

The extent of food processing can affect the nutritional quality of foodstuffs. Categorising foods by the level of processing emphasises the differences in nutritional quality between foods within the same food group and is likely useful for determining dietary processed food consumption. The present study aimed to categorise foods within Australian food composition databases according to the level of food processing using a processed food classification system, as well as assess the variation in the levels of processing within food groups. A processed foods classification system was applied to food and beverage items contained within Australian Food and Nutrient (AUSNUT) 2007 (n = 3874) and AUSNUT 2011-13 (n = 5740). The proportion of Minimally Processed (MP), Processed Culinary Ingredients (PCI) Processed (P) and Ultra Processed (ULP) by AUSNUT food group and the overall proportion of the four processed food categories across AUSNUT 2007 and AUSNUT 2011-13 were calculated. Across the food composition databases, the overall proportions of foods classified as MP, PCI, P and ULP were 27%, 3%, 26% and 44% for AUSNUT 2007 and 38%, 2%, 24% and 36% for AUSNUT 2011-13. Although there was wide variation in the classifications of food processing within the food groups, approximately one-third of foodstuffs were classified as ULP food items across both the 2007 and 2011-13 AUSNUT databases. This Australian processed food classification system will allow researchers to easily quantify the contribution of processed foods within the Australian food supply to assist in assessing the nutritional quality of the dietary intake of population groups. © 2017 The British Dietetic Association Ltd.

Process and domain specificity in regions engaged for face processing: an fMRI study of perceptual differentiation.

PubMed

Collins, Heather R; Zhu, Xun; Bhatt, Ramesh S; Clark, Jonathan D; Joseph, Jane E

2012-12-01

The degree to which face-specific brain regions are specialized for different kinds of perceptual processing is debated. This study parametrically varied demands on featural, first-order configural, or second-order configural processing of faces and houses in a perceptual matching task to determine the extent to which the process of perceptual differentiation was selective for faces regardless of processing type (domain-specific account), specialized for specific types of perceptual processing regardless of category (process-specific account), engaged in category-optimized processing (i.e., configural face processing or featural house processing), or reflected generalized perceptual differentiation (i.e., differentiation that crosses category and processing type boundaries). ROIs were identified in a separate localizer run or with a similarity regressor in the face-matching runs. The predominant principle accounting for fMRI signal modulation in most regions was generalized perceptual differentiation. Nearly all regions showed perceptual differentiation for both faces and houses for more than one processing type, even if the region was identified as face-preferential in the localizer run. Consistent with process specificity, some regions showed perceptual differentiation for first-order processing of faces and houses (right fusiform face area and occipito-temporal cortex and right lateral occipital complex), but not for featural or second-order processing. Somewhat consistent with domain specificity, the right inferior frontal gyrus showed perceptual differentiation only for faces in the featural matching task. The present findings demonstrate that the majority of regions involved in perceptual differentiation of faces are also involved in differentiation of other visually homogenous categories.

Process- and Domain-Specificity in Regions Engaged for Face Processing: An fMRI Study of Perceptual Differentiation

PubMed Central

Collins, Heather R.; Zhu, Xun; Bhatt, Ramesh S.; Clark, Jonathan D.; Joseph, Jane E.

2015-01-01

The degree to which face-specific brain regions are specialized for different kinds of perceptual processing is debated. The present study parametrically varied demands on featural, first-order configural or second-order configural processing of faces and houses in a perceptual matching task to determine the extent to which the process of perceptual differentiation was selective for faces regardless of processing type (domain-specific account), specialized for specific types of perceptual processing regardless of category (process-specific account), engaged in category-optimized processing (i.e., configural face processing or featural house processing) or reflected generalized perceptual differentiation (i.e. differentiation that crosses category and processing type boundaries). Regions of interest were identified in a separate localizer run or with a similarity regressor in the face-matching runs. The predominant principle accounting for fMRI signal modulation in most regions was generalized perceptual differentiation. Nearly all regions showed perceptual differentiation for both faces and houses for more than one processing type, even if the region was identified as face-preferential in the localizer run. Consistent with process-specificity, some regions showed perceptual differentiation for first-order processing of faces and houses (right fusiform face area and occipito-temporal cortex, and right lateral occipital complex), but not for featural or second-order processing. Somewhat consistent with domain-specificity, the right inferior frontal gyrus showed perceptual differentiation only for faces in the featural matching task. The present findings demonstrate that the majority of regions involved in perceptual differentiation of faces are also involved in differentiation of other visually homogenous categories. PMID:22849402

Achieving Continuous Manufacturing for Final Dosage Formation: Challenges and How to Meet Them May 20-21 2014 Continuous Manufacturing Symposium.

PubMed

Byrn, Stephen; Futran, Maricio; Thomas, Hayden; Jayjock, Eric; Maron, Nicola; Meyer, Robert F; Myerson, Allan S; Thien, Michael P; Trout, Bernhardt L

2015-03-01

We describe the key issues and possibilities for continuous final dosage formation, otherwise known as downstream processing or drug product manufacturing. A distinction is made between heterogeneous processing and homogeneous processing, the latter of which is expected to add more value to continuous manufacturing. We also give the key motivations for moving to continuous manufacturing, some of the exciting new technologies, and the barriers to implementation of continuous manufacturing. Continuous processing of heterogeneous blends is the natural first step in converting existing batch processes to continuous. In heterogeneous processing, there are discrete particles that can segregate, versus in homogeneous processing, components are blended and homogenized such that they do not segregate. Heterogeneous processing can incorporate technologies that are closer to existing technologies, where homogeneous processing necessitates the development and incorporation of new technologies. Homogeneous processing has the greatest potential for reaping the full rewards of continuous manufacturing, but it takes long-term vision and a more significant change in process development than heterogeneous processing. Heterogeneous processing has the detriment that, as the technologies are adopted rather than developed, there is a strong tendency to incorporate correction steps, what we call below "The Rube Goldberg Problem." Thus, although heterogeneous processing will likely play a major role in the near-term transformation of heterogeneous to continuous processing, it is expected that homogeneous processing is the next step that will follow. Specific action items for industry leaders are. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

An Analysis of the Air Force Government Operated Civil Engineering Supply Store Logistic System: How Can It Be Improved?

DTIC Science & Technology

1990-09-01

6 Logistics Systems ............ 7 GOCESS Operation . . . . . . . ..... 9 Work Order Processing . . . . ... 12 Job Order Processing . . . . . . . . . . 14...orders and job orders to the Material Control Section will be discussed separately. Work Order Processing . Figure 2 illustrates typical WO processing...logistics function. The JO processing is similar. Job Order Processing . Figure 3 illustrates typical JO processing in a GOCESS operation. As with WOs, this

Adaptive-optics optical coherence tomography processing using a graphics processing unit.

PubMed

Shafer, Brandon A; Kriske, Jeffery E; Kocaoglu, Omer P; Turner, Timothy L; Liu, Zhuolin; Lee, John Jaehwan; Miller, Donald T

2014-01-01

Graphics processing units are increasingly being used for scientific computing for their powerful parallel processing abilities, and moderate price compared to super computers and computing grids. In this paper we have used a general purpose graphics processing unit to process adaptive-optics optical coherence tomography (AOOCT) images in real time. Increasing the processing speed of AOOCT is an essential step in moving the super high resolution technology closer to clinical viability.

Data processing system for the Sneg-2MP experiment

NASA Technical Reports Server (NTRS)

Gavrilova, Y. A.

1980-01-01

The data processing system for scientific experiments on stations of the "Prognoz" type provides for the processing sequence to be broken down into a number of consecutive stages: preliminary processing, primary processing, secondary processing. The tasks of each data processing stage are examined for an experiment designed to study gamma flashes of galactic origin and solar flares lasting from several minutes to seconds in the 20 kev to 1000 kev energy range.

General RMP Guidance - Appendix D: OSHA Guidance on PSM

EPA Pesticide Factsheets

OSHA's Process Safety Management (PSM) Guidance on providing complete and accurate written information concerning process chemicals, process technology, and process equipment; including process hazard analysis and material safety data sheets.

Elaboration Likelihood and the Counseling Process: The Role of Affect.

ERIC Educational Resources Information Center

Stoltenberg, Cal D.; And Others

The role of affect in counseling has been examined from several orientations. The depth of processing model views the efficiency of information processing as a function of the extent to which the information is processed. The notion of cognitive processing capacity states that processing information at deeper levels engages more of one's limited…

5 CFR 582.202 - Service of legal process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false Service of legal process. 582.202 Section... GARNISHMENT OF FEDERAL EMPLOYEES' PAY Service of Legal Process § 582.202 Service of legal process. (a) A person using this part shall serve interrogatories and legal process on the agent to receive process as...

5 CFR 582.202 - Service of legal process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 5 Administrative Personnel 1 2014-01-01 2014-01-01 false Service of legal process. 582.202 Section... GARNISHMENT OF FEDERAL EMPLOYEES' PAY Service of Legal Process § 582.202 Service of legal process. (a) A person using this part shall serve interrogatories and legal process on the agent to receive process as...

Information Processing Concepts: A Cure for "Technofright." Information Processing in the Electronic Office. Part 1: Concepts.

ERIC Educational Resources Information Center

Popyk, Marilyn K.

1986-01-01

Discusses the new automated office and its six major technologies (data processing, word processing, graphics, image, voice, and networking), the information processing cycle (input, processing, output, distribution/communication, and storage and retrieval), ergonomics, and ways to expand office education classes (versus class instruction). (CT)

Facial Speech Gestures: The Relation between Visual Speech Processing, Phonological Awareness, and Developmental Dyslexia in 10-Year-Olds

ERIC Educational Resources Information Center

Schaadt, Gesa; Männel, Claudia; van der Meer, Elke; Pannekamp, Ann; Friederici, Angela D.

2016-01-01

Successful communication in everyday life crucially involves the processing of auditory and visual components of speech. Viewing our interlocutor and processing visual components of speech facilitates speech processing by triggering auditory processing. Auditory phoneme processing, analyzed by event-related brain potentials (ERP), has been shown…

40 CFR 65.62 - Process vent group determination.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., or Group 2B) for each process vent. Group 1 process vents require control, and Group 2A and 2B... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Process vent group determination. 65... (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Process Vents § 65.62 Process vent group determination. (a) Group...

40 CFR 63.138 - Process wastewater provisions-performance standards for treatment processes managing Group 1...

Code of Federal Regulations, 2010 CFR

2010-07-01

.../or Table 9 compounds are similar and often identical. (3) Biological treatment processes. Biological treatment processes in compliance with this section may be either open or closed biological treatment processes as defined in § 63.111. An open biological treatment process in compliance with this section need...

5 CFR 581.202 - Service of process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Service of process. 581.202 Section 581... GARNISHMENT ORDERS FOR CHILD SUPPORT AND/OR ALIMONY Service of Process § 581.202 Service of process. (a) A... facilitate proper service of process on its designated agent(s). If legal process is not directed to any...

30 CFR 828.11 - In situ processing: Performance standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false In situ processing: Performance standards. 828... STANDARDS-IN SITU PROCESSING § 828.11 In situ processing: Performance standards. (a) The person who conducts in situ processing activities shall comply with 30 CFR 817 and this section. (b) In situ processing...

30 CFR 828.11 - In situ processing: Performance standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false In situ processing: Performance standards. 828... STANDARDS-IN SITU PROCESSING § 828.11 In situ processing: Performance standards. (a) The person who conducts in situ processing activities shall comply with 30 CFR 817 and this section. (b) In situ processing...

30 CFR 828.11 - In situ processing: Performance standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false In situ processing: Performance standards. 828... STANDARDS-IN SITU PROCESSING § 828.11 In situ processing: Performance standards. (a) The person who conducts in situ processing activities shall comply with 30 CFR 817 and this section. (b) In situ processing...

30 CFR 828.11 - In situ processing: Performance standards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false In situ processing: Performance standards. 828... STANDARDS-IN SITU PROCESSING § 828.11 In situ processing: Performance standards. (a) The person who conducts in situ processing activities shall comply with 30 CFR 817 and this section. (b) In situ processing...

30 CFR 828.11 - In situ processing: Performance standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false In situ processing: Performance standards. 828... STANDARDS-IN SITU PROCESSING § 828.11 In situ processing: Performance standards. (a) The person who conducts in situ processing activities shall comply with 30 CFR 817 and this section. (b) In situ processing...

Processing Depth, Elaboration of Encoding, Memory Stores, and Expended Processing Capacity.

ERIC Educational Resources Information Center

Eysenck, Michael W.; Eysenck, M. Christine

1979-01-01

The effects of several factors on expended processing capacity were measured. Expended processing capacity was greater when information was retrieved from secondary memory than from primary memory, when processing was of a deep, semantic nature than when it was shallow and physical, and when processing was more elaborate. (Author/GDC)

Speed isn’t everything: Complex processing speed measures mask individual differences and developmental changes in executive control

PubMed Central

Cepeda, Nicholas J.; Blackwell, Katharine A.; Munakata, Yuko

2012-01-01

The rate at which people process information appears to influence many aspects of cognition across the lifespan. However, many commonly accepted measures of “processing speed” may require goal maintenance, manipulation of information in working memory, and decision-making, blurring the distinction between processing speed and executive control and resulting in overestimation of processing-speed contributions to cognition. This concern may apply particularly to studies of developmental change, as even seemingly simple processing speed measures may require executive processes to keep children and older adults on task. We report two new studies and a re-analysis of a published study, testing predictions about how different processing speed measures influence conclusions about executive control across the life span. We find that the choice of processing speed measure affects the relationship observed between processing speed and executive control, in a manner that changes with age, and that choice of processing speed measure affects conclusions about development and the relationship among executive control measures. Implications for understanding processing speed, executive control, and their development are discussed. PMID:23432836

The impact of working memory and the “process of process modelling” on model quality: Investigating experienced versus inexperienced modellers

NASA Astrophysics Data System (ADS)

Martini, Markus; Pinggera, Jakob; Neurauter, Manuel; Sachse, Pierre; Furtner, Marco R.; Weber, Barbara

2016-05-01

A process model (PM) represents the graphical depiction of a business process, for instance, the entire process from online ordering a book until the parcel is delivered to the customer. Knowledge about relevant factors for creating PMs of high quality is lacking. The present study investigated the role of cognitive processes as well as modelling processes in creating a PM in experienced and inexperienced modellers. Specifically, two working memory (WM) functions (holding and processing of information and relational integration) and three process of process modelling phases (comprehension, modelling, and reconciliation) were related to PM quality. Our results show that the WM function of relational integration was positively related to PM quality in both modelling groups. The ratio of comprehension phases was negatively related to PM quality in inexperienced modellers and the ratio of reconciliation phases was positively related to PM quality in experienced modellers. Our research reveals central cognitive mechanisms in process modelling and has potential practical implications for the development of modelling software and teaching the craft of process modelling.

A new class of random processes with application to helicopter noise

NASA Technical Reports Server (NTRS)

Hardin, Jay C.; Miamee, A. G.

1989-01-01

The concept of dividing random processes into classes (e.g., stationary, locally stationary, periodically correlated, and harmonizable) has long been employed. A new class of random processes is introduced which includes many of these processes as well as other interesting processes which fall into none of the above classes. Such random processes are denoted as linearly correlated. This class is shown to include the familiar stationary and periodically correlated processes as well as many other, both harmonizable and non-harmonizable, nonstationary processes. When a process is linearly correlated for all t and harmonizable, its two-dimensional power spectral density S(x) (omega 1, omega 2) is shown to take a particularly simple form, being non-zero only on lines such that omega 1 to omega 2 = + or - r(k) where the r(k's) are (not necessarily equally spaced) roots of a characteristic function. The relationship of such processes to the class of stationary processes is examined. In addition, the application of such processes in the analysis of typical helicopter noise signals is described.

The impact of working memory and the “process of process modelling” on model quality: Investigating experienced versus inexperienced modellers

PubMed Central

Martini, Markus; Pinggera, Jakob; Neurauter, Manuel; Sachse, Pierre; Furtner, Marco R.; Weber, Barbara

2016-01-01

A process model (PM) represents the graphical depiction of a business process, for instance, the entire process from online ordering a book until the parcel is delivered to the customer. Knowledge about relevant factors for creating PMs of high quality is lacking. The present study investigated the role of cognitive processes as well as modelling processes in creating a PM in experienced and inexperienced modellers. Specifically, two working memory (WM) functions (holding and processing of information and relational integration) and three process of process modelling phases (comprehension, modelling, and reconciliation) were related to PM quality. Our results show that the WM function of relational integration was positively related to PM quality in both modelling groups. The ratio of comprehension phases was negatively related to PM quality in inexperienced modellers and the ratio of reconciliation phases was positively related to PM quality in experienced modellers. Our research reveals central cognitive mechanisms in process modelling and has potential practical implications for the development of modelling software and teaching the craft of process modelling. PMID:27157858

A new class of random processes with application to helicopter noise

NASA Technical Reports Server (NTRS)

Hardin, Jay C.; Miamee, A. G.

1989-01-01

The concept of dividing random processes into classes (e.g., stationary, locally stationary, periodically correlated, and harmonizable) has long been employed. A new class of random processes is introduced which includes many of these processes as well as other interesting processes which fall into none of the above classes. Such random processes are denoted as linearly correlated. This class is shown to include the familiar stationary and periodically correlated processes as well as many other, both harmonizable and non-harmonizable, nonstationary processes. When a process is linearly correlated for all t and harmonizable, its two-dimensional power spectral density S(x)(omega 1, omega 2) is shown to take a particularly simple form, being non-zero only on lines such that omega 1 to omega 2 = + or - r(k) where the r(k's) are (not necessarily equally spaced) roots of a characteristic function. The relationship of such processes to the class of stationary processes is examined. In addition, the application of such processes in the analysis of typical helicopter noise signals is described.

The impact of working memory and the "process of process modelling" on model quality: Investigating experienced versus inexperienced modellers.

PubMed

Martini, Markus; Pinggera, Jakob; Neurauter, Manuel; Sachse, Pierre; Furtner, Marco R; Weber, Barbara

2016-05-09

A process model (PM) represents the graphical depiction of a business process, for instance, the entire process from online ordering a book until the parcel is delivered to the customer. Knowledge about relevant factors for creating PMs of high quality is lacking. The present study investigated the role of cognitive processes as well as modelling processes in creating a PM in experienced and inexperienced modellers. Specifically, two working memory (WM) functions (holding and processing of information and relational integration) and three process of process modelling phases (comprehension, modelling, and reconciliation) were related to PM quality. Our results show that the WM function of relational integration was positively related to PM quality in both modelling groups. The ratio of comprehension phases was negatively related to PM quality in inexperienced modellers and the ratio of reconciliation phases was positively related to PM quality in experienced modellers. Our research reveals central cognitive mechanisms in process modelling and has potential practical implications for the development of modelling software and teaching the craft of process modelling.

Rapid Automatized Naming in Children with Dyslexia: Is Inhibitory Control Involved?

PubMed

Bexkens, Anika; van den Wildenberg, Wery P M; Tijms, Jurgen

2015-08-01

Rapid automatized naming (RAN) is widely seen as an important indicator of dyslexia. The nature of the cognitive processes involved in rapid naming is however still a topic of controversy. We hypothesized that in addition to the involvement of phonological processes and processing speed, RAN is a function of inhibition processes, in particular of interference control. A total 86 children with dyslexia and 31 normal readers were recruited. Our results revealed that in addition to phonological processing and processing speed, interference control predicts rapid naming in dyslexia, but in contrast to these other two cognitive processes, inhibition is not significantly associated with their reading and spelling skills. After variance in reading and spelling associated with processing speed, interference control and phonological processing was partialled out, naming speed was no longer consistently associated with the reading and spelling skills of children with dyslexia. Finally, dyslexic children differed from normal readers on naming speed, literacy skills, phonological processing and processing speed, but not on inhibition processes. Both theoretical and clinical interpretations of these results are discussed. Copyright © 2014 John Wiley & Sons, Ltd.

Feasibility of using continuous chromatography in downstream processing: Comparison of costs and product quality for a hybrid process vs. a conventional batch process.

PubMed

Ötes, Ozan; Flato, Hendrik; Winderl, Johannes; Hubbuch, Jürgen; Capito, Florian

2017-10-10

The protein A capture step is the main cost-driver in downstream processing, with high attrition costs especially when using protein A resin not until end of resin lifetime. Here we describe a feasibility study, transferring a batch downstream process to a hybrid process, aimed at replacing batch protein A capture chromatography with a continuous capture step, while leaving the polishing steps unchanged to minimize required process adaptations compared to a batch process. 35g of antibody were purified using the hybrid approach, resulting in comparable product quality and step yield compared to the batch process. Productivity for the protein A step could be increased up to 420%, reducing buffer amounts by 30-40% and showing robustness for at least 48h continuous run time. Additionally, to enable its potential application in a clinical trial manufacturing environment cost of goods were compared for the protein A step between hybrid process and batch process, showing a 300% cost reduction, depending on processed volumes and batch cycles. Copyright © 2017 Elsevier B.V. All rights reserved.

Non-Conscious Perception of Emotions in Psychiatric Disorders: The Unsolved Puzzle of Psychopathology.

PubMed

Lee, Seung A; Kim, Chai-Youn; Lee, Seung-Hwan

2016-03-01

Psychophysiological and functional neuroimaging studies have frequently and consistently shown that emotional information can be processed outside of the conscious awareness. Non-conscious processing comprises automatic, uncontrolled, and fast processing that occurs without subjective awareness. However, how such non-conscious emotional processing occurs in patients with various psychiatric disorders requires further examination. In this article, we reviewed and discussed previous studies on the non-conscious emotional processing in patients diagnosed with anxiety disorder, schizophrenia, bipolar disorder, and depression, to further understand how non-conscious emotional processing varies across these psychiatric disorders. Although the symptom profile of each disorder does not often overlap with one another, these patients commonly show abnormal emotional processing based on the pathology of their mood and cognitive function. This indicates that the observed abnormalities of emotional processing in certain social interactions may derive from a biased mood or cognition process that precedes consciously controlled and voluntary processes. Since preconscious forms of emotional processing appear to have a major effect on behaviour and cognition in patients with these disorders, further investigation is required to understand these processes and their impact on patient pathology.

Empirical evaluation of the Process Overview Measure for assessing situation awareness in process plants.

PubMed

Lau, Nathan; Jamieson, Greg A; Skraaning, Gyrd

2016-03-01

The Process Overview Measure is a query-based measure developed to assess operator situation awareness (SA) from monitoring process plants. A companion paper describes how the measure has been developed according to process plant properties and operator cognitive work. The Process Overview Measure demonstrated practicality, sensitivity, validity and reliability in two full-scope simulator experiments investigating dramatically different operational concepts. Practicality was assessed based on qualitative feedback of participants and researchers. The Process Overview Measure demonstrated sensitivity and validity by revealing significant effects of experimental manipulations that corroborated with other empirical results. The measure also demonstrated adequate inter-rater reliability and practicality for measuring SA in full-scope simulator settings based on data collected on process experts. Thus, full-scope simulator studies can employ the Process Overview Measure to reveal the impact of new control room technology and operational concepts on monitoring process plants. Practitioner Summary: The Process Overview Measure is a query-based measure that demonstrated practicality, sensitivity, validity and reliability for assessing operator situation awareness (SA) from monitoring process plants in representative settings.

A Framework for Business Process Change Requirements Analysis

NASA Astrophysics Data System (ADS)

Grover, Varun; Otim, Samuel

The ability to quickly and continually adapt business processes to accommodate evolving requirements and opportunities is critical for success in competitive environments. Without appropriate linkage between redesign decisions and strategic inputs, identifying processes that need to be modified will be difficult. In this paper, we draw attention to the analysis of business process change requirements in support of process change initiatives. Business process redesign is a multifaceted phenomenon involving processes, organizational structure, management systems, human resource architecture, and many other aspects of organizational life. To be successful, the business process initiative should focus not only on identifying the processes to be redesigned, but also pay attention to various enablers of change. Above all, a framework is just a blueprint; management must lead change. We hope our modest contribution will draw attention to the broader framing of requirements for business process change.

Process Analytical Technology (PAT): batch-to-batch reproducibility of fermentation processes by robust process operational design and control.

PubMed

Gnoth, S; Jenzsch, M; Simutis, R; Lübbert, A

2007-10-31

The Process Analytical Technology (PAT) initiative of the FDA is a reaction on the increasing discrepancy between current possibilities in process supervision and control of pharmaceutical production processes and its current application in industrial manufacturing processes. With rigid approval practices based on standard operational procedures, adaptations of production reactors towards the state of the art were more or less inhibited for long years. Now PAT paves the way for continuous process and product improvements through improved process supervision based on knowledge-based data analysis, "Quality-by-Design"-concepts, and, finally, through feedback control. Examples of up-to-date implementations of this concept are presented. They are taken from one key group of processes in recombinant pharmaceutical protein manufacturing, the cultivations of genetically modified Escherichia coli bacteria.

When teams shift among processes: insights from simulation and optimization.

PubMed

Kennedy, Deanna M; McComb, Sara A

2014-09-01

This article introduces process shifts to study the temporal interplay among transition and action processes espoused in the recurring phase model proposed by Marks, Mathieu, and Zacarro (2001). Process shifts are those points in time when teams complete a focal process and change to another process. By using team communication patterns to measure process shifts, this research explores (a) when teams shift among different transition processes and initiate action processes and (b) the potential of different interventions, such as communication directives, to manipulate process shift timing and order and, ultimately, team performance. Virtual experiments are employed to compare data from observed laboratory teams not receiving interventions, simulated teams receiving interventions, and optimal simulated teams generated using genetic algorithm procedures. Our results offer insights about the potential for different interventions to affect team performance. Moreover, certain interventions may promote discussions about key issues (e.g., tactical strategies) and facilitate shifting among transition processes in a manner that emulates optimal simulated teams' communication patterns. Thus, we contribute to theory regarding team processes in 2 important ways. First, we present process shifts as a way to explore the timing of when teams shift from transition to action processes. Second, we use virtual experimentation to identify those interventions with the greatest potential to affect performance by changing when teams shift among processes. Additionally, we employ computational methods including neural networks, simulation, and optimization, thereby demonstrating their applicability in conducting team research. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Nitrous oxide and methane emissions from different treatment processes in full-scale municipal wastewater treatment plants.

PubMed

Rena, Y G; Wang, J H; Li, H F; Zhang, J; Qi, P Y; Hu, Z

2013-01-01

Nitrous oxide (N2O) and methane (CH4) are two important greenhouse gases (GHG) emitted from biological nutrient removal (BNR) processes in municipal wastewater treatment plants (WWTP). In this study, three typical biological wastewater treatment processes were studied in WWTP of Northern China: pre-anaerobic carrousel oxidation ditch (A+OD) process, pre-anoxic anaerobic-anoxic-oxic (A-A/ A/O) process and reverse anaerobic-anoxic-oxic (r-A/ A/O) process. The N2O and CH4 emissions from these three different processes were measured in every processing unit of each WWTP. Results showed that N2O and CH4 were mainly discharged during the nitrification/denitrification process and the anaerobic/anoxic treatment process, respectively and the amounts of their formation and release were significantly influenced by different BNR processes implemented in these WWTP. The N2O conversion ratio of r-A/ A/O process was the lowest among the three WWTP, which were 10.9% and 18.6% lower than that of A-A/A/O process and A+OD process, respectively. Similarly, the CH4 conversion ratio of r-A/ A/O process was the lowest among the three WWTP, which were 89. I% and 80.8% lower than that of A-A/ A/O process and A+OD process, respectively. The factors influencing N2O and CH4 formation and emission in the three WWTP were investigated to explain the difference between these processes. The nitrite concentration and oxidation-reduction potential (ORP) value were found to be the dominant influencing factors affecting N2O and CH4 production, respectively. The flow-based emission factors of N2O and CH4 of the WWTP were figured out for better quantification of GHG emissions and further technical assessments of mitigation options.

Effects of children's working memory capacity and processing speed on their sentence imitation performance.

PubMed

Poll, Gerard H; Miller, Carol A; Mainela-Arnold, Elina; Adams, Katharine Donnelly; Misra, Maya; Park, Ji Sook

2013-01-01

More limited working memory capacity and slower processing for language and cognitive tasks are characteristics of many children with language difficulties. Individual differences in processing speed have not consistently been found to predict language ability or severity of language impairment. There are conflicting views on whether working memory and processing speed are integrated or separable abilities. To evaluate four models for the relations of individual differences in children's processing speed and working memory capacity in sentence imitation. The models considered whether working memory and processing speed are integrated or separable, as well as the effect of the number of operations required per sentence. The role of working memory as a mediator of the effect of processing speed on sentence imitation was also evaluated. Forty-six children with varied language and reading abilities imitated sentences. Working memory was measured with the Competing Language Processing Task (CLPT), and processing speed was measured with a composite of truth-value judgment and rapid automatized naming tasks. Mixed-effects ordinal regression models evaluated the CLPT and processing speed as predictors of sentence imitation item scores. A single mediator model evaluated working memory as a mediator of the effect of processing speed on sentence imitation total scores. Working memory was a reliable predictor of sentence imitation accuracy, but processing speed predicted sentence imitation only as a component of a processing speed by number of operations interaction. Processing speed predicted working memory capacity, and there was evidence that working memory acted as a mediator of the effect of processing speed on sentence imitation accuracy. The findings support a refined view of working memory and processing speed as separable factors in children's sentence imitation performance. Processing speed does not independently explain sentence imitation accuracy for all sentence types, but contributes when the task requires more mental operations. Processing speed also has an indirect effect on sentence imitation by contributing to working memory capacity. © 2013 Royal College of Speech and Language Therapists.

Q-marker based strategy for CMC research of Chinese medicine: A case study of Panax Notoginseng saponins.

PubMed

Zhong, Yi; Zhu, Jieqiang; Yang, Zhenzhong; Shao, Qing; Fan, Xiaohui; Cheng, Yiyu

2018-01-31

To ensure pharmaceutical quality, chemistry, manufacturing and control (CMC) research is essential. However, due to the inherent complexity of Chinese medicine (CM), CMC study of CM remains a great challenge for academia, industry, and regulatory agencies. Recently, quality-marker (Q-marker) was proposed to establish quality standards or quality analysis approaches of Chinese medicine, which sheds a light on Chinese medicine's CMC study. Here manufacture processes of Panax Notoginseng Saponins (PNS) is taken as a case study and the present work is to establish a Q-marker based research strategy for CMC of Chinese medicine. The Q-markers of Panax Notoginseng Saponins (PNS) is selected and established by integrating chemical profile with pharmacological activities. Then, the key processes of PNS manufacturing are identified by material flow analysis. Furthermore, modeling algorithms are employed to explore the relationship between Q-markers and critical process parameters (CPPs) of the key processes. At last, CPPs of the key processes are optimized in order to improving the process efficiency. Among the 97 identified compounds, Notoginsenoside R 1 , ginsenoside Rg 1 , Re, Rb 1 and Rd are selected as the Q-markers of PNS. Our analysis on PNS manufacturing show the extraction process and column chromatography process are the key processes. With the CPPs of each process as the inputs and Q-markers' contents as the outputs, two process prediction models are built separately for the extraction process and column chromatography process of Panax notoginseng, which both possess good prediction ability. Based on the efficiency models of extraction process and column chromatography process we constructed, the optimal CPPs of both processes are calculated. Our results show that the Q-markers derived from CMC research strategy can be applied to analyze the manufacturing processes of Chinese medicine to assure product's quality and promote key processes' efficiency simultaneously. Copyright © 2018 Elsevier GmbH. All rights reserved.

PyMS: a Python toolkit for processing of gas chromatography-mass spectrometry (GC-MS) data. Application and comparative study of selected tools

PubMed Central

2012-01-01

Background Gas chromatography–mass spectrometry (GC-MS) is a technique frequently used in targeted and non-targeted measurements of metabolites. Most existing software tools for processing of raw instrument GC-MS data tightly integrate data processing methods with graphical user interface facilitating interactive data processing. While interactive processing remains critically important in GC-MS applications, high-throughput studies increasingly dictate the need for command line tools, suitable for scripting of high-throughput, customized processing pipelines. Results PyMS comprises a library of functions for processing of instrument GC-MS data developed in Python. PyMS currently provides a complete set of GC-MS processing functions, including reading of standard data formats (ANDI- MS/NetCDF and JCAMP-DX), noise smoothing, baseline correction, peak detection, peak deconvolution, peak integration, and peak alignment by dynamic programming. A novel common ion single quantitation algorithm allows automated, accurate quantitation of GC-MS electron impact (EI) fragmentation spectra when a large number of experiments are being analyzed. PyMS implements parallel processing for by-row and by-column data processing tasks based on Message Passing Interface (MPI), allowing processing to scale on multiple CPUs in distributed computing environments. A set of specifically designed experiments was performed in-house and used to comparatively evaluate the performance of PyMS and three widely used software packages for GC-MS data processing (AMDIS, AnalyzerPro, and XCMS). Conclusions PyMS is a novel software package for the processing of raw GC-MS data, particularly suitable for scripting of customized processing pipelines and for data processing in batch mode. PyMS provides limited graphical capabilities and can be used both for routine data processing and interactive/exploratory data analysis. In real-life GC-MS data processing scenarios PyMS performs as well or better than leading software packages. We demonstrate data processing scenarios simple to implement in PyMS, yet difficult to achieve with many conventional GC-MS data processing software. Automated sample processing and quantitation with PyMS can provide substantial time savings compared to more traditional interactive software systems that tightly integrate data processing with the graphical user interface. PMID:22647087

The Research Process on Converter Steelmaking Process by Using Limestone

NASA Astrophysics Data System (ADS)

Tang, Biao; Li, Xing-yi; Cheng, Han-chi; Wang, Jing; Zhang, Yun-long

2017-08-01

Compared with traditional converter steelmaking process, steelmaking process with limestone uses limestone to replace lime partly. A lot of researchers have studied about the new steelmaking process. There are much related research about material balance calculation, the behaviour of limestone in the slag, limestone powder injection in converter and application of limestone in iron and steel enterprises. The results show that the surplus heat of converter can meet the need of the limestone calcination, and the new process can reduce the steelmaking process energy loss in the whole steelmaking process, reduce carbon dioxide emissions, and improve the quality of the gas.

Gas processing handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1982-04-01

Brief details are given of processes including: BGC-Lurgi slagging gasification, COGAS, Exxon catalytic coal gasification, FW-Stoic 2-stage, GI two stage, HYGAS, Koppers-Totzek, Lurgi pressure gasification, Saarberg-Otto, Shell, Texaco, U-Gas, W-D.IGI, Wellman-Galusha, Westinghouse, and Winkler coal gasification processes; the Rectisol process; the Catacarb and the Benfield processes for removing CO/SUB/2, H/SUB/2s and COS from gases produced by the partial oxidation of coal; the selectamine DD, Selexol solvent, and Sulfinol gas cleaning processes; the sulphur-tolerant shift (SSK) process; and the Super-meth process for the production of high-Btu gas from synthesis gas.

Working on the Boundaries: Philosophies and Practices of the Design Process

NASA Technical Reports Server (NTRS)

Ryan, R.; Blair, J.; Townsend, J.; Verderaime, V.

1996-01-01

While systems engineering process is a program formal management technique and contractually binding, the design process is the informal practice of achieving the design project requirements throughout all design phases of the systems engineering process. The design process and organization are systems and component dependent. Informal reviews include technical information meetings and concurrent engineering sessions, and formal technical discipline reviews are conducted through the systems engineering process. This paper discusses and references major philosophical principles in the design process, identifies its role in interacting systems and disciplines analyses and integrations, and illustrates the process application in experienced aerostructural designs.

Chemical processing of lunar materials

NASA Technical Reports Server (NTRS)

Criswell, D. R.; Waldron, R. D.

1979-01-01

The paper highlights recent work on the general problem of processing lunar materials. The discussion covers lunar source materials, refined products, motivations for using lunar materials, and general considerations for a lunar or space processing plant. Attention is given to chemical processing through various techniques, including electrolysis of molten silicates, carbothermic/silicothermic reduction, carbo-chlorination process, NaOH basic-leach process, and HF acid-leach process. Several options for chemical processing of lunar materials are well within the state of the art of applied chemistry and chemical engineering to begin development based on the extensive knowledge of lunar materials.

Coordination and organization of security software process for power information application environment

NASA Astrophysics Data System (ADS)

Wang, Qiang

2017-09-01

As an important part of software engineering, the software process decides the success or failure of software product. The design and development feature of security software process is discussed, so is the necessity and the present significance of using such process. Coordinating the function software, the process for security software and its testing are deeply discussed. The process includes requirement analysis, design, coding, debug and testing, submission and maintenance. In each process, the paper proposed the subprocesses to support software security. As an example, the paper introduces the above process into the power information platform.

Sensor-based atomic layer deposition for rapid process learning and enhanced manufacturability

NASA Astrophysics Data System (ADS)

Lei, Wei

In the search for sensor based atomic layer deposition (ALD) process to accelerate process learning and enhance manufacturability, we have explored new reactor designs and applied in-situ process sensing to W and HfO 2 ALD processes. A novel wafer scale ALD reactor, which features fast gas switching, good process sensing compatibility and significant similarity to the real manufacturing environment, is constructed. The reactor has a unique movable reactor cap design that allows two possible operation modes: (1) steady-state flow with alternating gas species; or (2) fill-and-pump-out cycling of each gas, accelerating the pump-out by lifting the cap to employ the large chamber volume as ballast. Downstream quadrupole mass spectrometry (QMS) sampling is applied for in-situ process sensing of tungsten ALD process. The QMS reveals essential surface reaction dynamics through real-time signals associated with byproduct generation as well as precursor introduction and depletion for each ALD half cycle, which are then used for process learning and optimization. More subtle interactions such as imperfect surface saturation and reactant dose interaction are also directly observed by QMS, indicating that ALD process is more complicated than the suggested layer-by-layer growth. By integrating in real-time the byproduct QMS signals over each exposure and plotting it against process cycle number, the deposition kinetics on the wafer is directly measured. For continuous ALD runs, the total integrated byproduct QMS signal in each ALD run is also linear to ALD film thickness, and therefore can be used for ALD film thickness metrology. The in-situ process sensing is also applied to HfO2 ALD process that is carried out in a furnace type ALD reactor. Precursor dose end-point control is applied to precisely control the precursor dose in each half cycle. Multiple process sensors, including quartz crystal microbalance (QCM) and QMS are used to provide real time process information. The sensing results confirm the proposed surface reaction path and once again reveal the complexity of ALD processes. The impact of this work includes: (1) It explores new ALD reactor designs which enable the implementation of in-situ process sensors for rapid process learning and enhanced manufacturability; (2) It demonstrates in the first time that in-situ QMS can reveal detailed process dynamics and film growth kinetics in wafer-scale ALD process, and thus can be used for ALD film thickness metrology. (3) Based on results from two different processes carried out in two different reactors, it is clear that ALD is a more complicated process than normally believed or advertised, but real-time observation of the operational chemistries in ALD by in-situ sensors provides critical insight to the process and the basis for more effective process control for ALD applications.

Implicit Processes, Self-Regulation, and Interventions for Behavior Change.

PubMed

St Quinton, Tom; Brunton, Julie A

2017-01-01

The ability to regulate and subsequently change behavior is influenced by both reflective and implicit processes. Traditional theories have focused on conscious processes by highlighting the beliefs and intentions that influence decision making. However, their success in changing behavior has been modest with a gap between intention and behavior apparent. Dual-process models have been recently applied to health psychology; with numerous models incorporating implicit processes that influence behavior as well as the more common conscious processes. Such implicit processes are theorized to govern behavior non-consciously. The article provides a commentary on motivational and volitional processes and how interventions have combined to attempt an increase in positive health behaviors. Following this, non-conscious processes are discussed in terms of their theoretical underpinning. The article will then highlight how these processes have been measured and will then discuss the different ways that the non-conscious and conscious may interact. The development of interventions manipulating both processes may well prove crucial in successfully altering behavior.

All varieties of encoding variability are not created equal: Separating variable processing from variable tasks

PubMed Central

Huff, Mark J.; Bodner, Glen E.

2014-01-01

Whether encoding variability facilitates memory is shown to depend on whether item-specific and relational processing are both performed across study blocks, and whether study items are weakly versus strongly related. Variable-processing groups studied a word list once using an item-specific task and once using a relational task. Variable-task groups’ two different study tasks recruited the same type of processing each block. Repeated-task groups performed the same study task each block. Recall and recognition were greatest in the variable-processing group, but only with weakly related lists. A variable-processing benefit was also found when task-based processing and list-type processing were complementary (e.g., item-specific processing of a related list) rather than redundant (e.g., relational processing of a related list). That performing both item-specific and relational processing across trials, or within a trial, yields encoding-variability benefits may help reconcile decades of contradictory findings in this area. PMID:25018583

Continuous welding of unidirectional fiber reinforced thermoplastic tape material

NASA Astrophysics Data System (ADS)

Schledjewski, Ralf

2017-10-01

Continuous welding techniques like thermoplastic tape placement with in situ consolidation offer several advantages over traditional manufacturing processes like autoclave consolidation, thermoforming, etc. However, still there is a need to solve several important processing issues before it becomes a viable economic process. Intensive process analysis and optimization has been carried out in the past through experimental investigation, model definition and simulation development. Today process simulation is capable to predict resulting consolidation quality. Effects of material imperfections or process parameter variations are well known. But using this knowledge to control the process based on online process monitoring and according adaption of the process parameters is still challenging. Solving inverse problems and using methods for automated code generation allowing fast implementation of algorithms on targets are required. The paper explains the placement technique in general. Process-material-property-relationships and typical material imperfections are described. Furthermore, online monitoring techniques and how to use them for a model based process control system are presented.

Economics of polysilicon process: A view from Japan

NASA Technical Reports Server (NTRS)

Shimizu, Y.

1986-01-01

The production process of solar grade silicon (SOG-Si) through trichlorosilane (TCS) was researched in a program sponsored by New Energy Development Organization (NEDO). The NEDO process consists of the following two steps: TCS production from by-product silicon tetrachloride (STC) and SOG-Si formation from TCS using a fluidized bed reactor. Based on the data obtained during the research program, the manufacturing cost of the NEDO process and other polysilicon manufacturing processes were compared. The manufacturing cost was calculated on the basis of 1000 tons/year production. The cost estimate showed that the cost of producing silicon by all of the new processes is less than the cost by the conventional Siemens process. Using a new process, the cost of producing semiconductor grade silicon was found to be virtually the same with any to the TCS, diclorosilane, and monosilane processes when by-products were recycled. The SOG-Si manufacturing processes using the fluidized bed reactor, which needs further development, shows a greater probablility of cost reduction than the filament processes.

Autonomous Agents for Dynamic Process Planning in the Flexible Manufacturing System

NASA Astrophysics Data System (ADS)

Nik Nejad, Hossein Tehrani; Sugimura, Nobuhiro; Iwamura, Koji; Tanimizu, Yoshitaka

Rapid changes of market demands and pressures of competition require manufacturers to maintain highly flexible manufacturing systems to cope with a complex manufacturing environment. This paper deals with development of an agent-based architecture of dynamic systems for incremental process planning in the manufacturing systems. In consideration of alternative manufacturing processes and machine tools, the process plans and the schedules of the manufacturing resources are generated incrementally and dynamically. A negotiation protocol is discussed, in this paper, to generate suitable process plans for the target products real-timely and dynamically, based on the alternative manufacturing processes. The alternative manufacturing processes are presented by the process plan networks discussed in the previous paper, and the suitable process plans are searched and generated to cope with both the dynamic changes of the product specifications and the disturbances of the manufacturing resources. We initiatively combine the heuristic search algorithms of the process plan networks with the negotiation protocols, in order to generate suitable process plans in the dynamic manufacturing environment.

Implicit Processes, Self-Regulation, and Interventions for Behavior Change

PubMed Central

St Quinton, Tom; Brunton, Julie A.

2017-01-01

The ability to regulate and subsequently change behavior is influenced by both reflective and implicit processes. Traditional theories have focused on conscious processes by highlighting the beliefs and intentions that influence decision making. However, their success in changing behavior has been modest with a gap between intention and behavior apparent. Dual-process models have been recently applied to health psychology; with numerous models incorporating implicit processes that influence behavior as well as the more common conscious processes. Such implicit processes are theorized to govern behavior non-consciously. The article provides a commentary on motivational and volitional processes and how interventions have combined to attempt an increase in positive health behaviors. Following this, non-conscious processes are discussed in terms of their theoretical underpinning. The article will then highlight how these processes have been measured and will then discuss the different ways that the non-conscious and conscious may interact. The development of interventions manipulating both processes may well prove crucial in successfully altering behavior. PMID:28337164

Models of recognition: a review of arguments in favor of a dual-process account.

PubMed

Diana, Rachel A; Reder, Lynne M; Arndt, Jason; Park, Heekyeong

2006-02-01

The majority of computationally specified models of recognition memory have been based on a single-process interpretation, claiming that familiarity is the only influence on recognition. There is increasing evidence that recognition is, in fact, based on two processes: recollection and familiarity. This article reviews the current state of the evidence for dual-process models, including the usefulness of the remember/know paradigm, and interprets the relevant results in terms of the source of activation confusion (SAC) model of memory. We argue that the evidence from each of the areas we discuss, when combined, presents a strong case that inclusion of a recollection process is necessary. Given this conclusion, we also argue that the dual-process claim that the recollection process is always available is, in fact, more parsimonious than the single-process claim that the recollection process is used only in certain paradigms. The value of a well-specified process model such as the SAC model is discussed with regard to other types of dual-process models.

Integrating Thermal Tools Into the Mechanical Design Process

NASA Technical Reports Server (NTRS)

Tsuyuki, Glenn T.; Siebes, Georg; Novak, Keith S.; Kinsella, Gary M.

1999-01-01

The intent of mechanical design is to deliver a hardware product that meets or exceeds customer expectations, while reducing cycle time and cost. To this end, an integrated mechanical design process enables the idea of parallel development (concurrent engineering). This represents a shift from the traditional mechanical design process. With such a concurrent process, there are significant issues that have to be identified and addressed before re-engineering the mechanical design process to facilitate concurrent engineering. These issues also assist in the integration and re-engineering of the thermal design sub-process since it resides within the entire mechanical design process. With these issues in mind, a thermal design sub-process can be re-defined in a manner that has a higher probability of acceptance, thus enabling an integrated mechanical design process. However, the actual implementation is not always problem-free. Experience in applying the thermal design sub-process to actual situations provides the evidence for improvement, but more importantly, for judging the viability and feasibility of the sub-process.

[Monitoring method of extraction process for Schisandrae Chinensis Fructus based on near infrared spectroscopy and multivariate statistical process control].

PubMed

Xu, Min; Zhang, Lei; Yue, Hong-Shui; Pang, Hong-Wei; Ye, Zheng-Liang; Ding, Li

2017-10-01

To establish an on-line monitoring method for extraction process of Schisandrae Chinensis Fructus, the formula medicinal material of Yiqi Fumai lyophilized injection by combining near infrared spectroscopy with multi-variable data analysis technology. The multivariate statistical process control (MSPC) model was established based on 5 normal batches in production and 2 test batches were monitored by PC scores, DModX and Hotelling T2 control charts. The results showed that MSPC model had a good monitoring ability for the extraction process. The application of the MSPC model to actual production process could effectively achieve on-line monitoring for extraction process of Schisandrae Chinensis Fructus, and can reflect the change of material properties in the production process in real time. This established process monitoring method could provide reference for the application of process analysis technology in the process quality control of traditional Chinese medicine injections. Copyright© by the Chinese Pharmaceutical Association.

Method for automatically evaluating a transition from a batch manufacturing technique to a lean manufacturing technique

DOEpatents

Ivezic, Nenad; Potok, Thomas E.

2003-09-30

A method for automatically evaluating a manufacturing technique comprises the steps of: receiving from a user manufacturing process step parameters characterizing a manufacturing process; accepting from the user a selection for an analysis of a particular lean manufacturing technique; automatically compiling process step data for each process step in the manufacturing process; automatically calculating process metrics from a summation of the compiled process step data for each process step; and, presenting the automatically calculated process metrics to the user. A method for evaluating a transition from a batch manufacturing technique to a lean manufacturing technique can comprise the steps of: collecting manufacturing process step characterization parameters; selecting a lean manufacturing technique for analysis; communicating the selected lean manufacturing technique and the manufacturing process step characterization parameters to an automatic manufacturing technique evaluation engine having a mathematical model for generating manufacturing technique evaluation data; and, using the lean manufacturing technique evaluation data to determine whether to transition from an existing manufacturing technique to the selected lean manufacturing technique.

Process yield improvements with process control terminal for varian serial ion implanters

NASA Astrophysics Data System (ADS)

Higashi, Harry; Soni, Ameeta; Martinez, Larry; Week, Ken

Implant processes in a modern wafer production fab are extremely complex. There can be several types of misprocessing, i.e. wrong dose or species, double implants and missed implants. Process Control Terminals (PCT) for Varian 350Ds installed at Intel fabs were found to substantially reduce the number of misprocessing steps. This paper describes those misprocessing steps and their subsequent reduction with use of PCTs. Reliable and simple process control with serial process ion implanters has been in increasing demand. A well designed process control terminal greatly increases device yield by monitoring all pertinent implanter functions and enabling process engineering personnel to set up process recipes for simple and accurate system operation. By programming user-selectable interlocks, implant errors are reduced and those that occur are logged for further analysis and prevention. A process control terminal should also be compatible with office personal computers for greater flexibility in system use and data analysis. The impact from the capability of a process control terminal is increased productivity, ergo higher device yield.

An Aspect-Oriented Framework for Business Process Improvement

NASA Astrophysics Data System (ADS)

Pourshahid, Alireza; Mussbacher, Gunter; Amyot, Daniel; Weiss, Michael

Recently, many organizations invested in Business Process Management Systems (BPMSs) in order to automate and monitor their processes. Business Activity Monitoring is one of the essential modules of a BPMS as it provides the core monitoring capabilities. Although the natural step after process monitoring is process improvement, most of the existing systems do not provide the means to help users with the improvement step. In this paper, we address this issue by proposing an aspect-oriented framework that allows the impact of changes to business processes to be explored with what-if scenarios based on the most appropriate process redesign patterns among several possibilities. As the four cornerstones of a BPMS are process, goal, performance and validation views, these views need to be aligned automatically by any approach that intends to support automated improvement of business processes. Our framework therefore provides means to reflect process changes also in the other views of the business process. A health care case study presented as a proof of concept suggests that this novel approach is feasible.

Structure and Randomness of Continuous-Time, Discrete-Event Processes

NASA Astrophysics Data System (ADS)

Marzen, Sarah E.; Crutchfield, James P.

2017-10-01

Loosely speaking, the Shannon entropy rate is used to gauge a stochastic process' intrinsic randomness; the statistical complexity gives the cost of predicting the process. We calculate, for the first time, the entropy rate and statistical complexity of stochastic processes generated by finite unifilar hidden semi-Markov models—memoryful, state-dependent versions of renewal processes. Calculating these quantities requires introducing novel mathematical objects (ɛ -machines of hidden semi-Markov processes) and new information-theoretic methods to stochastic processes.

Combined mesophilic anaerobic and thermophilic aerobic digestion process for high-strength food wastewater to increase removal efficiency and reduce sludge discharge.

PubMed

Jang, H M; Park, S K; Ha, J H; Park, J M

2014-01-01

In this study, a process that combines the mesophilic anaerobic digestion (MAD) process with thermophilic aerobic digestion (TAD) for high-strength food wastewater (FWW) treatment was developed to examine the removal of organic matter and methane production. All effluent discharged from the MAD process was separated into solid and liquid portions. The liquid part was discarded and the sludge part was passed to the TAD process for further degradation. Then, the digested sludge from the TAD process was recycled back to the MAD unit to achieve low sludge discharge from the combined process. The reactor combination was operated in two phases: during Phase I, 40 d of total hydraulic retention time (HRT) was applied; during Phase II, 20 d was applied. HRT of the TAD process was fixed at 5 d. For a comparison, a control process (single-stage MAD) was operated with the same HRTs of the combined process. Our results indicated that the combined process showed over 90% total solids, volatile solids and chemical oxygen demand removal efficiencies. In addition, the combined process showed a significantly higher methane production rate than that of the control process. Consequently, the experimental data demonstrated that the combined MAD-TAD process was successfully employed for high-strength FWW treatment with highly efficient organic matter reduction and methane production.

Leading processes of patient care and treatment in hierarchical healthcare organizations in Sweden--process managers' experiences.

PubMed

Nilsson, Kerstin; Sandoff, Mette

2015-01-01

The purpose of this study is to gain better understanding of the roles and functions of process managers by describing Swedish process managers' experiences of leading processes involving patient care and treatment when working in a hierarchical health-care organization. This study is based on an explorative design. The data were gathered from interviews with 12 process managers at three Swedish hospitals. These data underwent qualitative and interpretative analysis with a modified editing style. The process managers' experiences of leading processes in a hierarchical health-care organization are described under three themes: having or not having a mandate, exposure to conflict situations and leading process development. The results indicate a need for clarity regarding process manager's responsibility and work content, which need to be communicated to all managers and staff involved in the patient care and treatment process, irrespective of department. There also needs to be an emphasis on realistic expectations and orientation of the goals that are an intrinsic part of the task of being a process manager. Generalizations from the results of the qualitative interview studies are limited, but a deeper understanding of the phenomenon was reached, which, in turn, can be transferred to similar settings. This study contributes qualitative descriptions of leading care and treatment processes in a functional, hierarchical health-care organization from process managers' experiences, a subject that has not been investigated earlier.

Information Technology Process Improvement Decision-Making: An Exploratory Study from the Perspective of Process Owners and Process Managers

ERIC Educational Resources Information Center

Lamp, Sandra A.

2012-01-01

There is information available in the literature that discusses information technology (IT) governance and investment decision making from an executive-level perception, yet there is little information available that offers the perspective of process owners and process managers pertaining to their role in IT process improvement and investment…

43 CFR 2884.17 - How will BLM process my Processing Category 6 application?

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false How will BLM process my Processing...-WAY UNDER THE MINERAL LEASING ACT Applying for MLA Grants or TUPs § 2884.17 How will BLM process my... written agreement that describes how BLM will process your application. The final agreement consists of a...

43 CFR 2884.17 - How will BLM process my Processing Category 6 application?

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false How will BLM process my Processing...-WAY UNDER THE MINERAL LEASING ACT Applying for MLA Grants or TUPs § 2884.17 How will BLM process my... written agreement that describes how BLM will process your application. The final agreement consists of a...

15 CFR 15.3 - Acceptance of service of process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Acceptance of service of process. 15.3... Process § 15.3 Acceptance of service of process. (a) Except as otherwise provided in this subpart, any... employee by law is to be served personally with process. Service of process in this case is inadequate when...

Weaknesses in Applying a Process Approach in Industry Enterprises

NASA Astrophysics Data System (ADS)

Kučerová, Marta; Mĺkva, Miroslava; Fidlerová, Helena

2012-12-01

The paper deals with a process approach as one of the main principles of the quality management. Quality management systems based on process approach currently represents one of a proofed ways how to manage an organization. The volume of sales, costs and profit levels are influenced by quality of processes and efficient process flow. As results of the research project showed, there are some weaknesses in applying of the process approach in the industrial routine and it has been often only a formal change of the functional management to process management in many organizations in Slovakia. For efficient process management it is essential that companies take attention to the way how to organize their processes and seek for their continuous improvement.

Is Primary-Process Cognition a Feature of Hypnosis?

PubMed

Finn, Michael T; Goldman, Jared I; Lyon, Gyrid B; Nash, Michael R

2017-01-01

The division of cognition into primary and secondary processes is an important part of contemporary psychoanalytic metapsychology. Whereas primary processes are most characteristic of unconscious thought and loose associations, secondary processes generally govern conscious thought and logical reasoning. It has been theorized that an induction into hypnosis is accompanied by a predomination of primary-process cognition over secondary-process cognition. The authors hypothesized that highly hypnotizable individuals would demonstrate more primary-process cognition as measured by a recently developed cognitive-perceptual task. This hypothesis was not supported. In fact, low hypnotizable participants demonstrated higher levels of primary-process cognition. Exploratory analyses suggested a more specific effect: felt connectedness to the hypnotist seemed to promote secondary-process cognition among low hypnotizable participants.

[Dual process in large number estimation under uncertainty].

PubMed

Matsumuro, Miki; Miwa, Kazuhisa; Terai, Hitoshi; Yamada, Kento

2016-08-01

According to dual process theory, there are two systems in the mind: an intuitive and automatic System 1 and a logical and effortful System 2. While many previous studies about number estimation have focused on simple heuristics and automatic processes, the deliberative System 2 process has not been sufficiently studied. This study focused on the System 2 process for large number estimation. First, we described an estimation process based on participants’ verbal reports. The task, corresponding to the problem-solving process, consisted of creating subgoals, retrieving values, and applying operations. Second, we investigated the influence of such deliberative process by System 2 on intuitive estimation by System 1, using anchoring effects. The results of the experiment showed that the System 2 process could mitigate anchoring effects.

Object-processing neural efficiency differentiates object from spatial visualizers.

PubMed

Motes, Michael A; Malach, Rafael; Kozhevnikov, Maria

2008-11-19

The visual system processes object properties and spatial properties in distinct subsystems, and we hypothesized that this distinction might extend to individual differences in visual processing. We conducted a functional MRI study investigating the neural underpinnings of individual differences in object versus spatial visual processing. Nine participants of high object-processing ability ('object' visualizers) and eight participants of high spatial-processing ability ('spatial' visualizers) were scanned, while they performed an object-processing task. Object visualizers showed lower bilateral neural activity in lateral occipital complex and lower right-lateralized neural activity in dorsolateral prefrontal cortex. The data indicate that high object-processing ability is associated with more efficient use of visual-object resources, resulting in less neural activity in the object-processing pathway.

Process simulation for advanced composites production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allendorf, M.D.; Ferko, S.M.; Griffiths, S.

1997-04-01

The objective of this project is to improve the efficiency and lower the cost of chemical vapor deposition (CVD) processes used to manufacture advanced ceramics by providing the physical and chemical understanding necessary to optimize and control these processes. Project deliverables include: numerical process models; databases of thermodynamic and kinetic information related to the deposition process; and process sensors and software algorithms that can be used for process control. Target manufacturing techniques include CVD fiber coating technologies (used to deposit interfacial coatings on continuous fiber ceramic preforms), chemical vapor infiltration, thin-film deposition processes used in the glass industry, and coatingmore » techniques used to deposit wear-, abrasion-, and corrosion-resistant coatings for use in the pulp and paper, metals processing, and aluminum industries.« less

CDO budgeting

NASA Astrophysics Data System (ADS)

Nesladek, Pavel; Wiswesser, Andreas; Sass, Björn; Mauermann, Sebastian

2008-04-01

The Critical dimension off-target (CDO) is a key parameter for mask house customer, affecting directly the performance of the mask. The CDO is the difference between the feature size target and the measured feature size. The change of CD during the process is either compensated within the process or by data correction. These compensation methods are commonly called process bias and data bias, respectively. The difference between data bias and process bias in manufacturing results in systematic CDO error, however, this systematic error does not take into account the instability of the process bias. This instability is a result of minor variations - instabilities of manufacturing processes and changes in materials and/or logistics. Using several masks the CDO of the manufacturing line can be estimated. For systematic investigation of the unit process contribution to CDO and analysis of the factors influencing the CDO contributors, a solid understanding of each unit process and huge number of masks is necessary. Rough identification of contributing processes and splitting of the final CDO variation between processes can be done with approx. 50 masks with identical design, material and process. Such amount of data allows us to identify the main contributors and estimate the effect of them by means of Analysis of variance (ANOVA) combined with multivariate analysis. The analysis does not provide information about the root cause of the variation within the particular unit process, however, it provides a good estimate of the impact of the process on the stability of the manufacturing line. Additionally this analysis can be used to identify possible interaction between processes, which cannot be investigated if only single processes are considered. Goal of this work is to evaluate limits for CDO budgeting models given by the precision and the number of measurements as well as partitioning the variation within the manufacturing process. The CDO variation splits according to the suggested model into contributions from particular processes or process groups. Last but not least the power of this method to determine the absolute strength of each parameter will be demonstrated. Identification of the root cause of this variation within the unit process itself is not scope of this work.

Application of high-throughput mini-bioreactor system for systematic scale-down modeling, process characterization, and control strategy development.

PubMed

Janakiraman, Vijay; Kwiatkowski, Chris; Kshirsagar, Rashmi; Ryll, Thomas; Huang, Yao-Ming

2015-01-01

High-throughput systems and processes have typically been targeted for process development and optimization in the bioprocessing industry. For process characterization, bench scale bioreactors have been the system of choice. Due to the need for performing different process conditions for multiple process parameters, the process characterization studies typically span several months and are considered time and resource intensive. In this study, we have shown the application of a high-throughput mini-bioreactor system viz. the Advanced Microscale Bioreactor (ambr15(TM) ), to perform process characterization in less than a month and develop an input control strategy. As a pre-requisite to process characterization, a scale-down model was first developed in the ambr system (15 mL) using statistical multivariate analysis techniques that showed comparability with both manufacturing scale (15,000 L) and bench scale (5 L). Volumetric sparge rates were matched between ambr and manufacturing scale, and the ambr process matched the pCO2 profiles as well as several other process and product quality parameters. The scale-down model was used to perform the process characterization DoE study and product quality results were generated. Upon comparison with DoE data from the bench scale bioreactors, similar effects of process parameters on process yield and product quality were identified between the two systems. We used the ambr data for setting action limits for the critical controlled parameters (CCPs), which were comparable to those from bench scale bioreactor data. In other words, the current work shows that the ambr15(TM) system is capable of replacing the bench scale bioreactor system for routine process development and process characterization. © 2015 American Institute of Chemical Engineers.

Consumers' conceptualization of ultra-processed foods.

PubMed

Ares, Gastón; Vidal, Leticia; Allegue, Gimena; Giménez, Ana; Bandeira, Elisa; Moratorio, Ximena; Molina, Verónika; Curutchet, María Rosa

2016-10-01

Consumption of ultra-processed foods has been associated with low diet quality, obesity and other non-communicable diseases. This situation makes it necessary to develop educational campaigns to discourage consumers from substituting meals based on unprocessed or minimally processed foods by ultra-processed foods. In this context, the aim of the present work was to investigate how consumers conceptualize the term ultra-processed foods and to evaluate if the foods they perceive as ultra-processed are in concordance with the products included in the NOVA classification system. An online study was carried out with 2381 participants. They were asked to explain what they understood by ultra-processed foods and to list foods that can be considered ultra-processed. Responses were analysed using inductive coding. The great majority of the participants was able to provide an explanation of what ultra-processed foods are, which was similar to the definition described in the literature. Most of the participants described ultra-processed foods as highly processed products that usually contain additives and other artificial ingredients, stressing that they have low nutritional quality and are unhealthful. The most relevant products for consumers' conceptualization of the term were in agreement with the NOVA classification system and included processed meats, soft drinks, snacks, burgers, powdered and packaged soups and noodles. However, some of the participants perceived processed foods, culinary ingredients and even some minimally processed foods as ultra-processed. This suggests that in order to accurately convey their message, educational campaigns aimed at discouraging consumers from consuming ultra-processed foods should include a clear definition of the term and describe some of their specific characteristics, such as the type of ingredients included in their formulation and their nutritional composition. Copyright © 2016 Elsevier Ltd. All rights reserved.

Rapid communication: Global-local processing affects recognition of distractor emotional faces.

PubMed

Srinivasan, Narayanan; Gupta, Rashmi

2011-03-01

Recent studies have shown links between happy faces and global, distributed attention as well as sad faces to local, focused attention. Emotions have been shown to affect global-local processing. Given that studies on emotion-cognition interactions have not explored the effect of perceptual processing at different spatial scales on processing stimuli with emotional content, the present study investigated the link between perceptual focus and emotional processing. The study investigated the effects of global-local processing on the recognition of distractor faces with emotional expressions. Participants performed a digit discrimination task with digits at either the global level or the local level presented against a distractor face (happy or sad) as background. The results showed that global processing associated with broad scope of attention facilitates recognition of happy faces, and local processing associated with narrow scope of attention facilitates recognition of sad faces. The novel results of the study provide conclusive evidence for emotion-cognition interactions by demonstrating the effect of perceptual processing on emotional faces. The results along with earlier complementary results on the effect of emotion on global-local processing support a reciprocal relationship between emotional processing and global-local processing. Distractor processing with emotional information also has implications for theories of selective attention.

Tomographical process monitoring of laser transmission welding with OCT

NASA Astrophysics Data System (ADS)

Ackermann, Philippe; Schmitt, Robert

2017-06-01

Process control of laser processes still encounters many obstacles. Although these processes are stable, a narrow process parameter window during the process or process deviations have led to an increase on the requirements for the process itself and on monitoring devices. Laser transmission welding as a contactless and locally limited joining technique is well-established in a variety of demanding production areas. For example, sensitive parts demand a particle-free joining technique which does not affect the inner components. Inline integrated non-destructive optical measurement systems capable of providing non-invasive tomographical images of the transparent material, the weld seam and its surrounding areas with micron resolution would improve the overall process. Obtained measurement data enable qualitative feedback into the system to adapt parameters for a more robust process. Within this paper we present the inline monitoring device based on Fourier-domain optical coherence tomography developed within the European-funded research project "Manunet Weldable". This device, after adaptation to the laser transmission welding process is optically and mechanically integrated into the existing laser system. The main target lies within the inline process control destined to extract tomographical geometrical measurement data from the weld seam forming process. Usage of this technology makes offline destructive testing of produced parts obsolete. 1,2,3,4

A quality-refinement process for medical imaging applications.

PubMed

Neuhaus, J; Maleike, D; Nolden, M; Kenngott, H-G; Meinzer, H-P; Wolf, I

2009-01-01

To introduce and evaluate a process for refinement of software quality that is suitable to research groups. In order to avoid constraining researchers too much, the quality improvement process has to be designed carefully. The scope of this paper is to present and evaluate a process to advance quality aspects of existing research prototypes in order to make them ready for initial clinical studies. The proposed process is tailored for research environments and therefore more lightweight than traditional quality management processes. Focus on quality criteria that are important at the given stage of the software life cycle. Usage of tools that automate aspects of the process is emphasized. To evaluate the additional effort that comes along with the process, it was exemplarily applied for eight prototypical software modules for medical image processing. The introduced process has been applied to improve the quality of all prototypes so that they could be successfully used in clinical studies. The quality refinement yielded an average of 13 person days of additional effort per project. Overall, 107 bugs were found and resolved by applying the process. Careful selection of quality criteria and the usage of automated process tools lead to a lightweight quality refinement process suitable for scientific research groups that can be applied to ensure a successful transfer of technical software prototypes into clinical research workflows.

Negative Binomial Process Count and Mixture Modeling.

PubMed

Zhou, Mingyuan; Carin, Lawrence

2015-02-01

The seemingly disjoint problems of count and mixture modeling are united under the negative binomial (NB) process. A gamma process is employed to model the rate measure of a Poisson process, whose normalization provides a random probability measure for mixture modeling and whose marginalization leads to an NB process for count modeling. A draw from the NB process consists of a Poisson distributed finite number of distinct atoms, each of which is associated with a logarithmic distributed number of data samples. We reveal relationships between various count- and mixture-modeling distributions and construct a Poisson-logarithmic bivariate distribution that connects the NB and Chinese restaurant table distributions. Fundamental properties of the models are developed, and we derive efficient Bayesian inference. It is shown that with augmentation and normalization, the NB process and gamma-NB process can be reduced to the Dirichlet process and hierarchical Dirichlet process, respectively. These relationships highlight theoretical, structural, and computational advantages of the NB process. A variety of NB processes, including the beta-geometric, beta-NB, marked-beta-NB, marked-gamma-NB and zero-inflated-NB processes, with distinct sharing mechanisms, are also constructed. These models are applied to topic modeling, with connections made to existing algorithms under Poisson factor analysis. Example results show the importance of inferring both the NB dispersion and probability parameters.

[Process management in the hospital pharmacy for the improvement of the patient safety].

PubMed

Govindarajan, R; Perelló-Juncá, A; Parès-Marimòn, R M; Serrais-Benavente, J; Ferrandez-Martí, D; Sala-Robinat, R; Camacho-Calvente, A; Campabanal-Prats, C; Solà-Anderiu, I; Sanchez-Caparrós, S; Gonzalez-Estrada, J; Martinez-Olalla, P; Colomer-Palomo, J; Perez-Mañosas, R; Rodríguez-Gallego, D

2013-01-01

To define a process management model for a hospital pharmacy in order to measure, analyse and make continuous improvements in patient safety and healthcare quality. In order to implement process management, Igualada Hospital was divided into different processes, one of which was the Hospital Pharmacy. A multidisciplinary management team was given responsibility for each process. For each sub-process one person was identified to be responsible, and a working group was formed under his/her leadership. With the help of each working group, a risk analysis using failure modes and effects analysis (FMEA) was performed, and the corresponding improvement actions were implemented. Sub-process indicators were also identified, and different process management mechanisms were introduced. The first risk analysis with FMEA produced more than thirty preventive actions to improve patient safety. Later, the weekly analysis of errors, as well as the monthly analysis of key process indicators, permitted us to monitor process results and, as each sub-process manager participated in these meetings, also to assume accountability and responsibility, thus consolidating the culture of excellence. The introduction of different process management mechanisms, with the participation of people responsible for each sub-process, introduces a participative management tool for the continuous improvement of patient safety and healthcare quality. Copyright © 2012 SECA. Published by Elsevier Espana. All rights reserved.

Distributed processing method for arbitrary view generation in camera sensor network

NASA Astrophysics Data System (ADS)

Tehrani, Mehrdad P.; Fujii, Toshiaki; Tanimoto, Masayuki

2003-05-01

Camera sensor network as a new advent of technology is a network that each sensor node can capture video signals, process and communicate them with other nodes. The processing task in this network is to generate arbitrary view, which can be requested from central node or user. To avoid unnecessary communication between nodes in camera sensor network and speed up the processing time, we have distributed the processing tasks between nodes. In this method, each sensor node processes part of interpolation algorithm to generate the interpolated image with local communication between nodes. The processing task in camera sensor network is ray-space interpolation, which is an object independent method and based on MSE minimization by using adaptive filtering. Two methods were proposed for distributing processing tasks, which are Fully Image Shared Decentralized Processing (FIS-DP), and Partially Image Shared Decentralized Processing (PIS-DP), to share image data locally. Comparison of the proposed methods with Centralized Processing (CP) method shows that PIS-DP has the highest processing speed after FIS-DP, and CP has the lowest processing speed. Communication rate of CP and PIS-DP is almost same and better than FIS-DP. So, PIS-DP is recommended because of its better performance than CP and FIS-DP.

EEG alpha synchronization is related to top-down processing in convergent and divergent thinking

PubMed Central

Benedek, Mathias; Bergner, Sabine; Könen, Tanja; Fink, Andreas; Neubauer, Aljoscha C.

2011-01-01

Synchronization of EEG alpha activity has been referred to as being indicative of cortical idling, but according to more recent evidence it has also been associated with active internal processing and creative thinking. The main objective of this study was to investigate to what extent EEG alpha synchronization is related to internal processing demands and to specific cognitive process involved in creative thinking. To this end, EEG was measured during a convergent and a divergent thinking task (i.e., creativity-related task) which once were processed involving low and once involving high internal processing demands. High internal processing demands were established by masking the stimulus (after encoding) and thus preventing further bottom-up processing. Frontal alpha synchronization was observed during convergent and divergent thinking only under exclusive top-down control (high internal processing demands), but not when bottom-up processing was allowed (low internal processing demands). We conclude that frontal alpha synchronization is related to top-down control rather than to specific creativity-related cognitive processes. Frontal alpha synchronization, which has been observed in a variety of different creativity tasks, thus may not reflect a brain state that is specific for creative cognition but can probably be attributed to high internal processing demands which are typically involved in creative thinking. PMID:21925520

Kennedy Space Center Payload Processing

NASA Technical Reports Server (NTRS)

Lawson, Ronnie; Engler, Tom; Colloredo, Scott; Zide, Alan

2011-01-01

This slide presentation reviews the payload processing functions at Kennedy Space Center. It details some of the payloads processed at KSC, the typical processing tasks, the facilities available for processing payloads, and the capabilities and customer services that are available.

Improving the Document Development Process: Integrating Relational Data and Statistical Process Control.

ERIC Educational Resources Information Center

Miller, John

1994-01-01

Presents an approach to document numbering, document titling, and process measurement which, when used with fundamental techniques of statistical process control, reveals meaningful process-element variation as well as nominal productivity models. (SR)

USE OF INDICATOR ORGANISMS FOR DETERMINING PROCESS EFFECTIVENESS

EPA Science Inventory

Wastewaters, process effluents and treatment process residuals contain a variety of microorganisms. Many factors influence their densities as they move through collection systems and process equipment. Biological treatment systems rely on the catabolic processes of such microor...

Food processing by high hydrostatic pressure.

PubMed

Yamamoto, Kazutaka

2017-04-01

High hydrostatic pressure (HHP) process, as a nonthermal process, can be used to inactivate microbes while minimizing chemical reactions in food. In this regard, a HHP level of 100 MPa (986.9 atm/1019.7 kgf/cm 2 ) and more is applied to food. Conventional thermal process damages food components relating color, flavor, and nutrition via enhanced chemical reactions. However, HHP process minimizes the damages and inactivates microbes toward processing high quality safe foods. The first commercial HHP-processed foods were launched in 1990 as fruit products such as jams, and then some other products have been commercialized: retort rice products (enhanced water impregnation), cooked hams and sausages (shelf life extension), soy sauce with minimized salt (short-time fermentation owing to enhanced enzymatic reactions), and beverages (shelf life extension). The characteristics of HHP food processing are reviewed from viewpoints of nonthermal process, history, research and development, physical and biochemical changes, and processing equipment.

[Near infrared spectroscopy based process trajectory technology and its application in monitoring and controlling of traditional Chinese medicine manufacturing process].

PubMed

Li, Wen-Long; Qu, Hai-Bin

2016-10-01

In this paper, the principle of NIRS (near infrared spectroscopy)-based process trajectory technology was introduced.The main steps of the technique include:① in-line collection of the processes spectra of different technics; ② unfolding of the 3-D process spectra;③ determination of the process trajectories and their normal limits;④ monitoring of the new batches with the established MSPC (multivariate statistical process control) models.Applications of the technology in the chemical and biological medicines were reviewed briefly. By a comprehensive introduction of our feasibility research on the monitoring of traditional Chinese medicine technical process using NIRS-based multivariate process trajectories, several important problems of the practical applications which need urgent solutions are proposed, and also the application prospect of the NIRS-based process trajectory technology is fully discussed and put forward in the end. Copyright© by the Chinese Pharmaceutical Association.

Recollection is a continuous process: implications for dual-process theories of recognition memory.

PubMed

Mickes, Laura; Wais, Peter E; Wixted, John T

2009-04-01

Dual-process theory, which holds that recognition decisions can be based on recollection or familiarity, has long seemed incompatible with signal detection theory, which holds that recognition decisions are based on a singular, continuous memory-strength variable. Formal dual-process models typically regard familiarity as a continuous process (i.e., familiarity comes in degrees), but they construe recollection as a categorical process (i.e., recollection either occurs or does not occur). A continuous process is characterized by a graded relationship between confidence and accuracy, whereas a categorical process is characterized by a binary relationship such that high confidence is associated with high accuracy but all lower degrees of confidence are associated with chance accuracy. Using a source-memory procedure, we found that the relationship between confidence and source-recollection accuracy was graded. Because recollection, like familiarity, is a continuous process, dual-process theory is more compatible with signal detection theory than previously thought.

A qualitative assessment of a random process proposed as an atmospheric turbulence model

NASA Technical Reports Server (NTRS)

Sidwell, K.

1977-01-01

A random process is formed by the product of two Gaussian processes and the sum of that product with a third Gaussian process. The resulting total random process is interpreted as the sum of an amplitude modulated process and a slowly varying, random mean value. The properties of the process are examined, including an interpretation of the process in terms of the physical structure of atmospheric motions. The inclusion of the mean value variation gives an improved representation of the properties of atmospheric motions, since the resulting process can account for the differences in the statistical properties of atmospheric velocity components and their gradients. The application of the process to atmospheric turbulence problems, including the response of aircraft dynamic systems, is examined. The effects of the mean value variation upon aircraft loads are small in most cases, but can be important in the measurement and interpretation of atmospheric turbulence data.

Metals Recovery from Artificial Ore in Case of Printed Circuit Boards, Using Plasmatron Plasma Reactor

PubMed Central

Szałatkiewicz, Jakub

2016-01-01

This paper presents the investigation of metals production form artificial ore, which consists of printed circuit board (PCB) waste, processed in plasmatron plasma reactor. A test setup was designed and built that enabled research of plasma processing of PCB waste of more than 700 kg/day scale. The designed plasma process is presented and discussed. The process in tests consumed 2 kWh/kg of processed waste. Investigation of the process products is presented with their elemental analyses of metals and slag. The average recovery of metals in presented experiments is 76%. Metals recovered include: Ag, Au, Pd, Cu, Sn, Pb, and others. The chosen process parameters are presented: energy consumption, throughput, process temperatures, and air consumption. Presented technology allows processing of variable and hard-to-process printed circuit board waste that can reach up to 100% of the input mass. PMID:28773804

Characterisation and Processing of Some Iron Ores of India

NASA Astrophysics Data System (ADS)

Krishna, S. J. G.; Patil, M. R.; Rudrappa, C.; Kumar, S. P.; Ravi, B. P.

2013-10-01

Lack of process characterization data of the ores based on the granulometry, texture, mineralogy, physical, chemical, properties, merits and limitations of process, market and local conditions may mislead the mineral processing entrepreneur. The proper implementation of process characterization and geotechnical map data will result in optimized sustainable utilization of resource by processing. A few case studies of process characterization of some Indian iron ores are dealt with. The tentative ascending order of process refractoriness of iron ores is massive hematite/magnetite < marine black iron oxide sands < laminated soft friable siliceous ore fines < massive banded magnetite quartzite < laminated soft friable clayey aluminous ore fines < massive banded hematite quartzite/jasper < massive clayey hydrated iron oxide ore < manganese bearing iron ores massive < Ti-V bearing magnetite magmatic ore < ferruginous cherty quartzite. Based on diagnostic process characterization, the ores have been classified and generic process have been adopted for some Indian iron ores.

Measuring health care process quality with software quality measures.

PubMed

Yildiz, Ozkan; Demirörs, Onur

2012-01-01

Existing quality models focus on some specific diseases, clinics or clinical areas. Although they contain structure, process, or output type measures, there is no model which measures quality of health care processes comprehensively. In addition, due to the not measured overall process quality, hospitals cannot compare quality of processes internally and externally. To bring a solution to above problems, a new model is developed from software quality measures. We have adopted the ISO/IEC 9126 software quality standard for health care processes. Then, JCIAS (Joint Commission International Accreditation Standards for Hospitals) measurable elements were added to model scope for unifying functional requirements. Assessment (diagnosing) process measurement results are provided in this paper. After the application, it was concluded that the model determines weak and strong aspects of the processes, gives a more detailed picture for the process quality, and provides quantifiable information to hospitals to compare their processes with multiple organizations.

Thermal Stir Welding: A New Solid State Welding Process

NASA Technical Reports Server (NTRS)

Ding, R. Jeffrey

2003-01-01

Thermal stir welding is a new welding process developed at NASA's Marshall Space Flight Center in Huntsville, AL. Thermal stir welding is similar to friction stir welding in that it joins similar or dissimilar materials without melting the parent material. However, unlike friction stir welding, the heating, stirring and forging elements of the process are all independent of each other and are separately controlled. Furthermore, the heating element of the process can be either a solid-state process (such as a thermal blanket, induction type process, etc), or, a fusion process (YG laser, plasma torch, etc.) The separation of the heating, stirring, forging elements of the process allows more degrees of freedom for greater process control. This paper introduces the mechanics of the thermal stir welding process. In addition, weld mechanical property data is presented for selected alloys as well as metallurgical analysis.

Thermal Stir Welding: A New Solid State Welding Process

NASA Technical Reports Server (NTRS)

Ding, R. Jeffrey; Munafo, Paul M. (Technical Monitor)

2002-01-01

Thermal stir welding is a new welding process developed at NASA's Marshall Space Flight Center in Huntsville, AL. Thermal stir welding is similar to friction stir welding in that it joins similar or dissimilar materials without melting the parent material. However, unlike friction stir welding, the heating, stirring and forging elements of the process are all independent of each other and are separately controlled. Furthermore, the heating element of the process can be either a solid-state process (such as a thermal blanket, induction type process, etc), or, a fusion process (YG laser, plasma torch, etc.) The separation of the heating, stirring, forging elements of the process allows more degrees of freedom for greater process control. This paper introduces the mechanics of the thermal stir welding process. In addition, weld mechanical property data is presented for selected alloys as well as metallurgical analysis.

Metals Recovery from Artificial Ore in Case of Printed Circuit Boards, Using Plasmatron Plasma Reactor.

PubMed

Szałatkiewicz, Jakub

2016-08-10

This paper presents the investigation of metals production form artificial ore, which consists of printed circuit board (PCB) waste, processed in plasmatron plasma reactor. A test setup was designed and built that enabled research of plasma processing of PCB waste of more than 700 kg/day scale. The designed plasma process is presented and discussed. The process in tests consumed 2 kWh/kg of processed waste. Investigation of the process products is presented with their elemental analyses of metals and slag. The average recovery of metals in presented experiments is 76%. Metals recovered include: Ag, Au, Pd, Cu, Sn, Pb, and others. The chosen process parameters are presented: energy consumption, throughput, process temperatures, and air consumption. Presented technology allows processing of variable and hard-to-process printed circuit board waste that can reach up to 100% of the input mass.

The origins of levels-of-processing effects in a conceptual test: evidence for automatic influences of memory from the process-dissociation procedure.

PubMed

Bergerbest, Dafna; Goshen-Gottstein, Yonatan

2002-12-01

In three experiments, we explored automatic influences of memory in a conceptual memory task, as affected by a levels-of-processing (LoP) manipulation. We also explored the origins of the LoP effect by examining whether the effect emerged only when participants in the shallow condition truncated the perceptual processing (the lexical-processing hypothesis) or even when the entire word was encoded in this condition (the conceptual-processing hypothesis). Using the process-dissociation procedure and an implicit association-generation task, we found that the deep encoding condition yielded higher estimates of automatic influences than the shallow condition. In support of the conceptual processing hypothesis, the LoP effect was found even when the shallow task did not lead to truncated processing of the lexical units. We suggest that encoding for meaning is a prerequisite for automatic processing on conceptual tests of memory.

Exploring business process modelling paradigms and design-time to run-time transitions

NASA Astrophysics Data System (ADS)

Caron, Filip; Vanthienen, Jan

2016-09-01

The business process management literature describes a multitude of approaches (e.g. imperative, declarative or event-driven) that each result in a different mix of process flexibility, compliance, effectiveness and efficiency. Although the use of a single approach over the process lifecycle is often assumed, transitions between approaches at different phases in the process lifecycle may also be considered. This article explores several business process strategies by analysing the approaches at different phases in the process lifecycle as well as the various transitions.

System Engineering Concept Demonstration, Process Model. Volume 3

DTIC Science & Technology

1992-12-01

Process or Process Model The System Engineering process must be the enactment of the aforementioned definitions. Therefore, a process is an enactment of a...Prototype Tradeoff Scenario demonstrates six levels of abstraction in the Process Model. The Process Model symbology is explained within the "Help" icon ...dnofing no- ubeq t"vidi e /hn -am-a. lmi IzyuO ..pu Row _e._n au"c.ue-w’ ’- anuiildyidwile b ie htplup ?~imsav D symbo ,,ue,.dvu ,,dienl Flw s--..,fu..I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eun, H.C.; Cho, Y.Z.; Choi, J.H.

A regeneration process of LiCl-KCl eutectic waste salt generated from the pyrochemical process of spent nuclear fuel has been studied. This regeneration process is composed of a chemical conversion process and a vacuum distillation process. Through the regeneration process, a high efficiency of renewable salt recovery can be obtained from the waste salt and rare earth nuclides in the waste salt can be separated as oxide or phosphate forms. Thus, the regeneration process can contribute greatly to a reduction of the waste volume and a creation of durable final waste forms. (authors)

An open system approach to process reengineering in a healthcare operational environment.

PubMed

Czuchry, A J; Yasin, M M; Norris, J

2000-01-01

The objective of this study is to examine the applicability of process reengineering in a healthcare operational environment. The intake process of a mental healthcare service delivery system is analyzed systematically to identify process-related problems. A methodology which utilizes an open system orientation coupled with process reengineering is utilized to overcome operational and patient related problems associated with the pre-reengineered intake process. The systematic redesign of the intake process resulted in performance improvements in terms of cost, quality, service and timing.

Developing the JPL Engineering Processes

NASA Technical Reports Server (NTRS)

Linick, Dave; Briggs, Clark

2004-01-01

This paper briefly recounts the recent history of process reengineering at the NASA Jet Propulsion Laboratory, with a focus on the engineering processes. The JPL process structure is described and the process development activities of the past several years outlined. The main focus of the paper is on the current process structure, the emphasis on the flight project life cycle, the governance approach that lead to Flight Project Practices, and the remaining effort to capture process knowledge at the detail level of the work group.

Water-saving liquid-gas conditioning system

DOEpatents

Martin, Christopher; Zhuang, Ye

2014-01-14

A method for treating a process gas with a liquid comprises contacting a process gas with a hygroscopic working fluid in order to remove a constituent from the process gas. A system for treating a process gas with a liquid comprises a hygroscopic working fluid comprising a component adapted to absorb or react with a constituent of a process gas, and a liquid-gas contactor for contacting the working fluid and the process gas, wherein the constituent is removed from the process gas within the liquid-gas contactor.

Model for Simulating a Spiral Software-Development Process

NASA Technical Reports Server (NTRS)

Mizell, Carolyn; Curley, Charles; Nayak, Umanath

2010-01-01

A discrete-event simulation model, and a computer program that implements the model, have been developed as means of analyzing a spiral software-development process. This model can be tailored to specific development environments for use by software project managers in making quantitative cases for deciding among different software-development processes, courses of action, and cost estimates. A spiral process can be contrasted with a waterfall process, which is a traditional process that consists of a sequence of activities that include analysis of requirements, design, coding, testing, and support. A spiral process is an iterative process that can be regarded as a repeating modified waterfall process. Each iteration includes assessment of risk, analysis of requirements, design, coding, testing, delivery, and evaluation. A key difference between a spiral and a waterfall process is that a spiral process can accommodate changes in requirements at each iteration, whereas in a waterfall process, requirements are considered to be fixed from the beginning and, therefore, a waterfall process is not flexible enough for some projects, especially those in which requirements are not known at the beginning or may change during development. For a given project, a spiral process may cost more and take more time than does a waterfall process, but may better satisfy a customer's expectations and needs. Models for simulating various waterfall processes have been developed previously, but until now, there have been no models for simulating spiral processes. The present spiral-process-simulating model and the software that implements it were developed by extending a discrete-event simulation process model of the IEEE 12207 Software Development Process, which was built using commercially available software known as the Process Analysis Tradeoff Tool (PATT). Typical inputs to PATT models include industry-average values of product size (expressed as number of lines of code), productivity (number of lines of code per hour), and number of defects per source line of code. The user provides the number of resources, the overall percent of effort that should be allocated to each process step, and the number of desired staff members for each step. The output of PATT includes the size of the product, a measure of effort, a measure of rework effort, the duration of the entire process, and the numbers of injected, detected, and corrected defects as well as a number of other interesting features. In the development of the present model, steps were added to the IEEE 12207 waterfall process, and this model and its implementing software were made to run repeatedly through the sequence of steps, each repetition representing an iteration in a spiral process. Because the IEEE 12207 model is founded on a waterfall paradigm, it enables direct comparison of spiral and waterfall processes. The model can be used throughout a software-development project to analyze the project as more information becomes available. For instance, data from early iterations can be used as inputs to the model, and the model can be used to estimate the time and cost of carrying the project to completion.

Magnitude processing of symbolic and non-symbolic proportions: an fMRI study.

PubMed

Mock, Julia; Huber, Stefan; Bloechle, Johannes; Dietrich, Julia F; Bahnmueller, Julia; Rennig, Johannes; Klein, Elise; Moeller, Korbinian

2018-05-10

Recent research indicates that processing proportion magnitude is associated with activation in the intraparietal sulcus. Thus, brain areas associated with the processing of numbers (i.e., absolute magnitude) were activated during processing symbolic fractions as well as non-symbolic proportions. Here, we investigated systematically the cognitive processing of symbolic (e.g., fractions and decimals) and non-symbolic proportions (e.g., dot patterns and pie charts) in a two-stage procedure. First, we investigated relative magnitude-related activations of proportion processing. Second, we evaluated whether symbolic and non-symbolic proportions share common neural substrates. We conducted an fMRI study using magnitude comparison tasks with symbolic and non-symbolic proportions, respectively. As an indicator for magnitude-related processing of proportions, the distance effect was evaluated. A conjunction analysis indicated joint activation of specific occipito-parietal areas including right intraparietal sulcus (IPS) during proportion magnitude processing. More specifically, results indicate that the IPS, which is commonly associated with absolute magnitude processing, is involved in processing relative magnitude information as well, irrespective of symbolic or non-symbolic presentation format. However, we also found distinct activation patterns for the magnitude processing of the different presentation formats. Our findings suggest that processing for the separate presentation formats is not only associated with magnitude manipulations in the IPS, but also increasing demands on executive functions and strategy use associated with frontal brain regions as well as visual attention and encoding in occipital regions. Thus, the magnitude processing of proportions may not exclusively reflect processing of number magnitude information but also rather domain-general processes.

[Alcohol-purification technology and its particle sedimentation process in manufactory of Fufang Kushen injection].

PubMed

Liu, Xiaoqian; Tong, Yan; Wang, Jinyu; Wang, Ruizhen; Zhang, Yanxia; Wang, Zhimin

2011-11-01

Fufang Kushen injection was selected as the model drug, to optimize its alcohol-purification process and understand the characteristics of particle sedimentation process, and to investigate the feasibility of using process analytical technology (PAT) on traditional Chinese medicine (TCM) manufacturing. Total alkaloids (calculated by matrine, oxymatrine, sophoridine and oxysophoridine) and macrozamin were selected as quality evaluation markers to optimize the process of Fufang Kushen injection purification with alcohol. Process parameters of particulate formed in the alcohol-purification, such as the number, density and sedimentation velocity, were also determined to define the sedimentation time and well understand the process. The purification process was optimized as that alcohol is added to the concentrated extract solution (drug material) to certain concentration for 2 times and deposited the alcohol-solution containing drug-material to sediment for some time, i.e. 60% alcohol deposited for 36 hours, filter and then 80% -90% alcohol deposited for 6 hours in turn. The content of total alkaloids was decreased a little during the depositing process. The average settling time of particles with the diameters of 10, 25 microm were 157.7, 25.2 h in the first alcohol-purified process, and 84.2, 13.5 h in the second alcohol-purified process, respectively. The optimized alcohol-purification process remains the marker compositions better and compared with the initial process, it's time saving and much economy. The manufacturing quality of TCM-injection can be controlled by process. PAT pattern must be designed under the well understanding of process of TCM production.

Application of volume-retarded osmosis and low-pressure membrane hybrid process for water reclamation.

PubMed

Im, Sung-Ju; Choi, Jungwon; Lee, Jung-Gil; Jeong, Sanghyun; Jang, Am

2018-03-01

A new concept of volume-retarded osmosis and low-pressure membrane (VRO-LPM) hybrid process was developed and evaluated for the first time in this study. Commercially available forward osmosis (FO) and ultrafiltration (UF) membranes were employed in a VRO-LPM hybrid process to overcome energy limitations of draw solution (DS) regeneration and production of permeate in the FO process. To evaluate its feasibility as a water reclamation process, and to optimize the operational conditions, cross-flow FO and dead-end mode UF processes were individually evaluated. For the FO process, a DS concentration of 0.15 g mL -1 of polysulfonate styrene (PSS) was determined to be optimal, having a high flux with a low reverse salt flux. The UF membrane with a molecular weight cut-off of 1 kDa was chosen for its high PSS rejection in the LPM process. As a single process, UF (LPM) exhibited a higher flux than FO, but this could be controlled by adjusting the effective membrane area of the FO and UF membranes in the VRO-LPM system. The VRO-LPM hybrid process only required a circulation pump for the FO process. This led to a decrease in the specific energy consumption of the VRO-LPM process for potable water production, that was similar to the single FO process. Therefore, the newly developed VRO-LPM hybrid process, with an appropriate DS selection, can be used as an energy efficient water production method, and can outperform conventional water reclamation processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Quality control process improvement of flexible printed circuit board by FMEA

NASA Astrophysics Data System (ADS)

Krasaephol, Siwaporn; Chutima, Parames

2018-02-01

This research focuses on the quality control process improvement of Flexible Printed Circuit Board (FPCB), centred around model 7-Flex, by using Failure Mode and Effect Analysis (FMEA) method to decrease proportion of defective finished goods that are found at the final inspection process. Due to a number of defective units that were found at the final inspection process, high scraps may be escaped to customers. The problem comes from poor quality control process which is not efficient enough to filter defective products from in-process because there is no In-Process Quality Control (IPQC) or sampling inspection in the process. Therefore, the quality control process has to be improved by setting inspection gates and IPCQs at critical processes in order to filter the defective products. The critical processes are analysed by the FMEA method. IPQC is used for detecting defective products and reducing chances of defective finished goods escaped to the customers. Reducing proportion of defective finished goods also decreases scrap cost because finished goods incur higher scrap cost than work in-process. Moreover, defective products that are found during process can reflect the abnormal processes; therefore, engineers and operators should timely solve the problems. Improved quality control was implemented for 7-Flex production lines from July 2017 to September 2017. The result shows decreasing of the average proportion of defective finished goods and the average of Customer Manufacturers Lot Reject Rate (%LRR of CMs) equal to 4.5% and 4.1% respectively. Furthermore, cost saving of this quality control process equals to 100K Baht.

Formulating poultry processing sanitizers from alkaline salts of fatty acids

USDA-ARS?s Scientific Manuscript database

Though some poultry processing operations remove microorganisms from carcasses; other processing operations cause cross-contamination that spreads microorganisms between carcasses, processing water, and processing equipment. One method used by commercial poultry processors to reduce microbial contam...

Fabrication Process for Cantilever Beam Micromechanical Switches

DTIC Science & Technology

1993-08-01

Beam Design ................................................................... 13 B. Chemistry and Materials Used in Cantilever Beam Process...7 3. Photomask levels and composite...pp 410-413. 5 2. Cantilever Beam Fabrication Process The beam fabrication process incorporates four different photomasking levels with 62 processing

Reports of planetary geology program, 1983

NASA Technical Reports Server (NTRS)

Holt, H. E. (Compiler)

1984-01-01

Several areas of the Planetary Geology Program were addressed including outer solar system satellites, asteroids, comets, Venus, cratering processes and landform development, volcanic processes, aeolian processes, fluvial processes, periglacial and permafrost processes, geomorphology, remote sensing, tectonics and stratigraphy, and mapping.

Cognitive Processes in Discourse Comprehension: Passive Processes, Reader-Initiated Processes, and Evolving Mental Representations

ERIC Educational Resources Information Center

van den Broek, Paul; Helder, Anne

2017-01-01

As readers move through a text, they engage in various types of processes that, if all goes well, result in a mental representation that captures their interpretation of the text. With each new text segment the reader engages in passive and, at times, reader-initiated processes. These processes are strongly influenced by the readers'…

The Use of Knowledge Based Decision Support Systems in Reengineering Selected Processes in the U. S. Marine Corps

DTIC Science & Technology

2001-09-01

measurable benefit in terms of process efficiency and effectiveness, business process reengineering (BPR) is becoming increasingly important. BPR suggests...technology by businesses in hopes of achieving a measurable benefit in terms of process efficiency and effectiveness, business process...KOPER-LITE ........................................13 E. HOW MIGHT THE MILITARY BENEFIT FROM PROCESS REENGINEERING EFFORTS

30 CFR 206.181 - How do I establish processing costs for dual accounting purposes when I do not process the gas?

Code of Federal Regulations, 2010 CFR

2010-07-01

... accounting purposes when I do not process the gas? 206.181 Section 206.181 Mineral Resources MINERALS... Processing Allowances § 206.181 How do I establish processing costs for dual accounting purposes when I do not process the gas? Where accounting for comparison (dual accounting) is required for gas production...

Conceptual models of information processing

NASA Technical Reports Server (NTRS)

Stewart, L. J.

1983-01-01

The conceptual information processing issues are examined. Human information processing is defined as an active cognitive process that is analogous to a system. It is the flow and transformation of information within a human. The human is viewed as an active information seeker who is constantly receiving, processing, and acting upon the surrounding environmental stimuli. Human information processing models are conceptual representations of cognitive behaviors. Models of information processing are useful in representing the different theoretical positions and in attempting to define the limits and capabilities of human memory. It is concluded that an understanding of conceptual human information processing models and their applications to systems design leads to a better human factors approach.

Industrial application of semantic process mining

NASA Astrophysics Data System (ADS)

Espen Ingvaldsen, Jon; Atle Gulla, Jon

2012-05-01

Process mining relates to the extraction of non-trivial and useful information from information system event logs. It is a new research discipline that has evolved significantly since the early work on idealistic process logs. Over the last years, process mining prototypes have incorporated elements from semantics and data mining and targeted visualisation techniques that are more user-friendly to business experts and process owners. In this article, we present a framework for evaluating different aspects of enterprise process flows and address practical challenges of state-of-the-art industrial process mining. We also explore the inherent strengths of the technology for more efficient process optimisation.

Reliability and performance of a system-on-a-chip by predictive wear-out based activation of functional components

DOEpatents

Cher, Chen-Yong; Coteus, Paul W; Gara, Alan; Kursun, Eren; Paulsen, David P; Schuelke, Brian A; Sheets, II, John E; Tian, Shurong

2013-10-01

A processor-implemented method for determining aging of a processing unit in a processor the method comprising: calculating an effective aging profile for the processing unit wherein the effective aging profile quantifies the effects of aging on the processing unit; combining the effective aging profile with process variation data, actual workload data and operating conditions data for the processing unit; and determining aging through an aging sensor of the processing unit using the effective aging profile, the process variation data, the actual workload data, architectural characteristics and redundancy data, and the operating conditions data for the processing unit.

Fuzzy control of burnout of multilayer ceramic actuators

NASA Astrophysics Data System (ADS)

Ling, Alice V.; Voss, David; Christodoulou, Leo

1996-08-01

To improve the yield and repeatability of the burnout process of multilayer ceramic actuators (MCAs), an intelligent processing of materials (IPM-based) control system has been developed for the manufacture of MCAs. IPM involves the active (ultimately adaptive) control of a material process using empirical or analytical models and in situ sensing of critical process states (part features and process parameters) to modify the processing conditions in real time to achieve predefined product goals. Thus, the three enabling technologies for the IPM burnout control system are process modeling, in situ sensing and intelligent control. This paper presents the design of an IPM-based control strategy for the burnout process of MCAs.

Direct access inter-process shared memory

DOEpatents

Brightwell, Ronald B; Pedretti, Kevin; Hudson, Trammell B

2013-10-22

A technique for directly sharing physical memory between processes executing on processor cores is described. The technique includes loading a plurality of processes into the physical memory for execution on a corresponding plurality of processor cores sharing the physical memory. An address space is mapped to each of the processes by populating a first entry in a top level virtual address table for each of the processes. The address space of each of the processes is cross-mapped into each of the processes by populating one or more subsequent entries of the top level virtual address table with the first entry in the top level virtual address table from other processes.

Biotechnology in Food Production and Processing

NASA Astrophysics Data System (ADS)

Knorr, Dietrich; Sinskey, Anthony J.

1985-09-01

The food processing industry is the oldest and largest industry using biotechnological processes. Further development of food products and processes based on biotechnology depends upon the improvement of existing processes, such as fermentation, immobilized biocatalyst technology, and production of additives and processing aids, as well as the development of new opportunities for food biotechnology. Improvements are needed in the characterization, safety, and quality control of food materials, in processing methods, in waste conversion and utilization processes, and in currently used food microorganism and tissue culture systems. Also needed are fundamental studies of the structure-function relationship of food materials and of the cell physiology and biochemistry of raw materials.

What is a good public participation process? Five perspectives from the public.

PubMed

Webler, T; Tuler, S; Krueger, R

2001-03-01

It is now widely accepted that members of the public should be involved in environmental decision-making. This has inspired many to search for principles that characterize good public participation processes. In this paper we report on a study that identifies discourses about what defines a good process. Our case study was a forest planning process in northern New England and New York. We employed Q methodology to learn how participants characterize a good process differently, by selecting, defining, and privileging different principles. Five discourses, or perspectives, about good process emerged from our study. One perspective emphasizes that a good process acquires and maintains popular legitimacy. A second sees a good process as one that facilitates an ideological discussion. A third focuses on the fairness of the process. A fourth perspective conceptualizes participatory processes as a power struggle--in this instance a power play between local land-owning interests and outsiders. A fifth perspective highlights the need for leadership and compromise. Dramatic differences among these views suggest an important challenge for those responsible for designing and carrying out public participation processes. Conflicts may emerge about process designs because people disagree about what is good in specific contexts.

Alternating event processes during lifetimes: population dynamics and statistical inference.

PubMed

Shinohara, Russell T; Sun, Yifei; Wang, Mei-Cheng

2018-01-01

In the literature studying recurrent event data, a large amount of work has been focused on univariate recurrent event processes where the occurrence of each event is treated as a single point in time. There are many applications, however, in which univariate recurrent events are insufficient to characterize the feature of the process because patients experience nontrivial durations associated with each event. This results in an alternating event process where the disease status of a patient alternates between exacerbations and remissions. In this paper, we consider the dynamics of a chronic disease and its associated exacerbation-remission process over two time scales: calendar time and time-since-onset. In particular, over calendar time, we explore population dynamics and the relationship between incidence, prevalence and duration for such alternating event processes. We provide nonparametric estimation techniques for characteristic quantities of the process. In some settings, exacerbation processes are observed from an onset time until death; to account for the relationship between the survival and alternating event processes, nonparametric approaches are developed for estimating exacerbation process over lifetime. By understanding the population dynamics and within-process structure, the paper provide a new and general way to study alternating event processes.

Process mining in oncology using the MIMIC-III dataset

NASA Astrophysics Data System (ADS)

Prima Kurniati, Angelina; Hall, Geoff; Hogg, David; Johnson, Owen

2018-03-01

Process mining is a data analytics approach to discover and analyse process models based on the real activities captured in information systems. There is a growing body of literature on process mining in healthcare, including oncology, the study of cancer. In earlier work we found 37 peer-reviewed papers describing process mining research in oncology with a regular complaint being the limited availability and accessibility of datasets with suitable information for process mining. Publicly available datasets are one option and this paper describes the potential to use MIMIC-III, for process mining in oncology. MIMIC-III is a large open access dataset of de-identified patient records. There are 134 publications listed as using the MIMIC dataset, but none of them have used process mining. The MIMIC-III dataset has 16 event tables which are potentially useful for process mining and this paper demonstrates the opportunities to use MIMIC-III for process mining in oncology. Our research applied the L* lifecycle method to provide a worked example showing how process mining can be used to analyse cancer pathways. The results and data quality limitations are discussed along with opportunities for further work and reflection on the value of MIMIC-III for reproducible process mining research.

Research on the technique of large-aperture off-axis parabolic surface processing using tri-station machine and its applicability.

PubMed

Zhang, Xin; Luo, Xiao; Hu, Haixiang; Zhang, Xuejun

2015-09-01

In order to process large-aperture aspherical mirrors, we designed and constructed a tri-station machine processing center with a three station device, which bears vectored feed motion of up to 10 axes. Based on this processing center, an aspherical mirror-processing model is proposed, in which each station implements traversal processing of large-aperture aspherical mirrors using only two axes, while the stations are switchable, thus lowering cost and enhancing processing efficiency. The applicability of the tri-station machine is also analyzed. At the same time, a simple and efficient zero-calibration method for processing is proposed. To validate the processing model, using our processing center, we processed an off-axis parabolic SiC mirror with an aperture diameter of 1450 mm. The experimental results indicate that, with a one-step iterative process, the peak to valley (PV) and root mean square (RMS) of the mirror converged from 3.441 and 0.5203 μm to 2.637 and 0.2962 μm, respectively, where the RMS reduced by 43%. The validity and high accuracy of the model are thereby demonstrated.

Patterning of Indium Tin Oxide Films

NASA Technical Reports Server (NTRS)

Immer, Christopher

2008-01-01

A relatively rapid, economical process has been devised for patterning a thin film of indium tin oxide (ITO) that has been deposited on a polyester film. ITO is a transparent, electrically conductive substance made from a mixture of indium oxide and tin oxide that is commonly used in touch panels, liquid-crystal and plasma display devices, gas sensors, and solar photovoltaic panels. In a typical application, the ITO film must be patterned to form electrodes, current collectors, and the like. Heretofore it has been common practice to pattern an ITO film by means of either a laser ablation process or a photolithography/etching process. The laser ablation process includes the use of expensive equipment to precisely position and focus a laser. The photolithography/etching process is time-consuming. The present process is a variant of the direct toner process an inexpensive but often highly effective process for patterning conductors for printed circuits. Relative to a conventional photolithography/ etching process, this process is simpler, takes less time, and is less expensive. This process involves equipment that costs less than $500 (at 2005 prices) and enables patterning of an ITO film in a process time of less than about a half hour.

Assessment of Process Capability: the case of Soft Drinks Processing Unit

NASA Astrophysics Data System (ADS)

Sri Yogi, Kottala

2018-03-01

The process capability studies have significant impact in investigating process variation which is important in achieving product quality characteristics. Its indices are to measure the inherent variability of a process and thus to improve the process performance radically. The main objective of this paper is to understand capability of the process being produced within specification of the soft drinks processing unit, a premier brands being marketed in India. A few selected critical parameters in soft drinks processing: concentration of gas volume, concentration of brix, torque of crock has been considered for this study. Assessed some relevant statistical parameters: short term capability, long term capability as a process capability indices perspective. For assessment we have used real time data of soft drinks bottling company which is located in state of Chhattisgarh, India. As our research output suggested reasons for variations in the process which is validated using ANOVA and also predicted Taguchi cost function, assessed also predicted waste monetarily this shall be used by organization for improving process parameters. This research work has substantially benefitted the organization in understanding the various variations of selected critical parameters for achieving zero rejection.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dafler, J.R.; Sinnott, J.; Novil, M.

The first phase of a study to identify candidate processes and products suitable for future exploitation using high-temperature solar energy is presented. This phase has been principally analytical, consisting of techno-economic studies, thermodynamic assessments of chemical reactions and processes, and the determination of market potentials for major chemical commodities that use significant amounts of fossil resources today. The objective was to identify energy-intensive processes that would be suitable for the production of chemicals and fuels using solar energy process heat. Of particular importance was the comparison of relative costs and energy requirements for the selected solar product versus costs formore » the product derived from conventional processing. The assessment methodology used a systems analytical approach to identify processes and products having the greatest potential for solar energy-thermal processing. This approach was used to establish the basis for work to be carried out in subsequent phases of development. It has been the intent of the program to divide the analysis and process identification into the following three distinct areas: (1) process selection, (2) process evaluation, and (3) ranking of processes. Four conventional processes were selected for assessment namely, methanol synthesis, styrene monomer production, vinyl chloride monomer production, and terephthalic acid production.« less

An Application of X-Ray Fluorescence as Process Analytical Technology (PAT) to Monitor Particle Coating Processes.

PubMed

Nakano, Yoshio; Katakuse, Yoshimitsu; Azechi, Yasutaka

2018-06-01

An attempt to apply X-Ray Fluorescence (XRF) analysis to evaluate small particle coating process as a Process Analytical Technologies (PAT) was made. The XRF analysis was used to monitor coating level in small particle coating process with at-line manner. The small particle coating process usually consists of multiple coating processes. This study was conducted by a simple coating particles prepared by first coating of a model compound (DL-methionine) and second coating by talc on spherical microcrystalline cellulose cores. The particles with two layered coating are enough to demonstrate the small particle coating process. From the result by the small particle coating process, it was found that the XRF signal played different roles, resulting that XRF signals by first coating (layering) and second coating (mask coating) could demonstrate the extent with different mechanisms for the coating process. Furthermore, the particle coating of the different particle size has also been investigated to evaluate size effect of these coating processes. From these results, it was concluded that the XRF could be used as a PAT in monitoring particle coating processes and become powerful tool in pharmaceutical manufacturing.

Single-Run Single-Mask Inductively-Coupled-Plasma Reactive-Ion-Etching Process for Fabricating Suspended High-Aspect-Ratio Microstructures

NASA Astrophysics Data System (ADS)

Yang, Yao-Joe; Kuo, Wen-Cheng; Fan, Kuang-Chao

2006-01-01

In this work, we present a single-run single-mask (SRM) process for fabricating suspended high-aspect-ratio structures on standard silicon wafers using an inductively coupled plasma-reactive ion etching (ICP-RIE) etcher. This process eliminates extra fabrication steps which are required for structure release after trench etching. Released microstructures with 120 μm thickness are obtained by this process. The corresponding maximum aspect ratio of the trench is 28. The SRM process is an extended version of the standard process proposed by BOSCH GmbH (BOSCH process). The first step of the SRM process is a standard BOSCH process for trench etching, then a polymer layer is deposited on trench sidewalls as a protective layer for the subsequent structure-releasing step. The structure is released by dry isotropic etching after the polymer layer on the trench floor is removed. All the steps can be integrated into a single-run ICP process. Also, only one mask is required. Therefore, the process complexity and fabrication cost can be effectively reduced. Discussions on each SRM step and considerations for avoiding undesired etching of the silicon structures during the release process are also presented.

Auditory-musical processing in autism spectrum disorders: a review of behavioral and brain imaging studies.

PubMed

Ouimet, Tia; Foster, Nicholas E V; Tryfon, Ana; Hyde, Krista L

2012-04-01

Autism spectrum disorder (ASD) is a complex neurodevelopmental condition characterized by atypical social and communication skills, repetitive behaviors, and atypical visual and auditory perception. Studies in vision have reported enhanced detailed ("local") processing but diminished holistic ("global") processing of visual features in ASD. Individuals with ASD also show enhanced processing of simple visual stimuli but diminished processing of complex visual stimuli. Relative to the visual domain, auditory global-local distinctions, and the effects of stimulus complexity on auditory processing in ASD, are less clear. However, one remarkable finding is that many individuals with ASD have enhanced musical abilities, such as superior pitch processing. This review provides a critical evaluation of behavioral and brain imaging studies of auditory processing with respect to current theories in ASD. We have focused on auditory-musical processing in terms of global versus local processing and simple versus complex sound processing. This review contributes to a better understanding of auditory processing differences in ASD. A deeper comprehension of sensory perception in ASD is key to better defining ASD phenotypes and, in turn, may lead to better interventions. © 2012 New York Academy of Sciences.

Discrete State Change Model of Manufacturing Quality to Aid Assembly Process Design

NASA Astrophysics Data System (ADS)

Koga, Tsuyoshi; Aoyama, Kazuhiro

This paper proposes a representation model of the quality state change in an assembly process that can be used in a computer-aided process design system. In order to formalize the state change of the manufacturing quality in the assembly process, the functions, operations, and quality changes in the assembly process are represented as a network model that can simulate discrete events. This paper also develops a design method for the assembly process. The design method calculates the space of quality state change and outputs a better assembly process (better operations and better sequences) that can be used to obtain the intended quality state of the final product. A computational redesigning algorithm of the assembly process that considers the manufacturing quality is developed. The proposed method can be used to design an improved manufacturing process by simulating the quality state change. A prototype system for planning an assembly process is implemented and applied to the design of an auto-breaker assembly process. The result of the design example indicates that the proposed assembly process planning method outputs a better manufacturing scenario based on the simulation of the quality state change.

Effect of simulated mechanical recycling processes on the structure and properties of poly(lactic acid).

PubMed

Beltrán, F R; Lorenzo, V; Acosta, J; de la Orden, M U; Martínez Urreaga, J

2018-06-15

The aim of this work is to study the effects of different simulated mechanical recycling processes on the structure and properties of PLA. A commercial grade of PLA was melt compounded and compression molded, then subjected to two different recycling processes. The first recycling process consisted of an accelerated ageing and a second melt processing step, while the other recycling process included an accelerated ageing, a demanding washing process and a second melt processing step. The intrinsic viscosity measurements indicate that both recycling processes produce a degradation in PLA, which is more pronounced in the sample subjected to the washing process. DSC results suggest an increase in the mobility of the polymer chains in the recycled materials; however the degree of crystallinity of PLA seems unchanged. The optical, mechanical and gas barrier properties of PLA do not seem to be largely affected by the degradation suffered during the different recycling processes. These results suggest that, despite the degradation of PLA, the impact of the different simulated mechanical recycling processes on the final properties is limited. Thus, the potential use of recycled PLA in packaging applications is not jeopardized. Copyright © 2017 Elsevier Ltd. All rights reserved.

Consumption of ultra-processed foods predicts diet quality in Canada.

PubMed

Moubarac, Jean-Claude; Batal, M; Louzada, M L; Martinez Steele, E; Monteiro, C A

2017-01-01

This study describes food consumption patterns in Canada according to the types of food processing using the Nova classification and investigates the association between consumption of ultra-processed foods and the nutrient profile of the diet. Dietary intakes of 33,694 individuals from the 2004 Canadian Community Health Survey aged 2 years and above were analyzed. Food and drinks were classified using Nova into unprocessed or minimally processed foods, processed culinary ingredients, processed foods and ultra-processed foods. Average consumption (total daily energy intake) and relative consumption (% of total energy intake) provided by each of the food groups were calculated. Consumption of ultra-processed foods according to sex, age, education, residential location and relative family revenue was assessed. Mean nutrient content of ultra-processed foods and non-ultra-processed foods were compared, and the average nutrient content of the overall diet across quintiles of dietary share of ultra-processed foods was measured. In 2004, 48% of calories consumed by Canadians came from ultra-processed foods. Consumption of such foods was high amongst all socioeconomic groups, and particularly in children and adolescents. As a group, ultra-processed foods were grossly nutritionally inferior to non-ultra-processed foods. After adjusting for covariates, a significant and positive relationship was found between the dietary share of ultra-processed foods and the content in carbohydrates, free sugars, total and saturated fats and energy density, while an inverse relationship was observed with the dietary content in protein, fiber, vitamins A, C, D, B6 and B12, niacin, thiamine, riboflavin, as well as zinc, iron, magnesium, calcium, phosphorus and potassium. Lowering the dietary share of ultra-processed foods and raising consumption of hand-made meals from unprocessed or minimally processed foods would substantially improve the diet quality of Canadian. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of Statistical Process Control Methodology for an Environmentally Compliant Surface Cleaning Process in a Bonding Laboratory

NASA Technical Reports Server (NTRS)

Hutchens, Dale E.; Doan, Patrick A.; Boothe, Richard E.

1997-01-01

Bonding labs at both MSFC and the northern Utah production plant prepare bond test specimens which simulate or witness the production of NASA's Reusable Solid Rocket Motor (RSRM). The current process for preparing the bonding surfaces employs 1,1,1-trichloroethane vapor degreasing, which simulates the current RSRM process. Government regulations (e.g., the 1990 Amendments to the Clean Air Act) have mandated a production phase-out of a number of ozone depleting compounds (ODC) including 1,1,1-trichloroethane. In order to comply with these regulations, the RSRM Program is qualifying a spray-in-air (SIA) precision cleaning process using Brulin 1990, an aqueous blend of surfactants. Accordingly, surface preparation prior to bonding process simulation test specimens must reflect the new production cleaning process. The Bonding Lab Statistical Process Control (SPC) program monitors the progress of the lab and its capabilities, as well as certifies the bonding technicians, by periodically preparing D6AC steel tensile adhesion panels with EA-91 3NA epoxy adhesive using a standardized process. SPC methods are then used to ensure the process is statistically in control, thus producing reliable data for bonding studies, and identify any problems which might develop. Since the specimen cleaning process is being changed, new SPC limits must be established. This report summarizes side-by-side testing of D6AC steel tensile adhesion witness panels and tapered double cantilevered beams (TDCBs) using both the current baseline vapor degreasing process and a lab-scale spray-in-air process. A Proceco 26 inches Typhoon dishwasher cleaned both tensile adhesion witness panels and TDCBs in a process which simulates the new production process. The tests were performed six times during 1995, subsequent statistical analysis of the data established new upper control limits (UCL) and lower control limits (LCL). The data also demonstrated that the new process was equivalent to the vapor degreasing process.

Evaluation of stabilization techniques for ion implant processing

NASA Astrophysics Data System (ADS)

Ross, Matthew F.; Wong, Selmer S.; Minter, Jason P.; Marlowe, Trey; Narcy, Mark E.; Livesay, William R.

1999-06-01

With the integration of high current ion implant processing into volume CMOS manufacturing, the need for photoresist stabilization to achieve a stable ion implant process is critical. This study compares electron beam stabilization, a non-thermal process, with more traditional thermal stabilization techniques such as hot plate baking and vacuum oven processing. The electron beam processing is carried out in a flood exposure system with no active heating of the wafer. These stabilization techniques are applied to typical ion implant processes that might be found in a CMOS production process flow. The stabilization processes are applied to a 1.1 micrometers thick PFI-38A i-line photoresist film prior to ion implant processing. Post stabilization CD variation is detailed with respect to wall slope and feature integrity. SEM photographs detail the effects of the stabilization technique on photoresist features. The thermal stability of the photoresist is shown for different levels of stabilization and post stabilization thermal cycling. Thermal flow stability of the photoresist is detailed via SEM photographs. A significant improvement in thermal stability is achieved with the electron beam process, such that photoresist features are stable to temperatures in excess of 200 degrees C. Ion implant processing parameters are evaluated and compared for the different stabilization methods. Ion implant system end-station chamber pressure is detailed as a function of ion implant process and stabilization condition. The ion implant process conditions are detailed for varying factors such as ion current, energy, and total dose. A reduction in the ion implant systems end-station chamber pressure is achieved with the electron beam stabilization process over the other techniques considered. This reduction in end-station chamber pressure is shown to provide a reduction in total process time for a given ion implant dose. Improvements in the ion implant process are detailed across several combinations of current and energy.

The prevalence of medial coronoid process disease is high in lame large breed dogs and quantitative radiographic assessments contribute to the diagnosis.

PubMed

Mostafa, Ayman; Nolte, Ingo; Wefstaedt, Patrick

2018-06-05

Medial coronoid process disease is a common leading cause of thoracic limb lameness in dogs. Computed tomography and arthroscopy are superior to radiography to diagnose medial coronoid process disease, however, radiography remains the most available diagnostic imaging modality in veterinary practice. Objectives of this retrospective observational study were to describe the prevalence of medial coronoid process disease in lame large breed dogs and apply a novel method for quantifying the radiographic changes associated with medial coronoid process and subtrochlear-ulnar region in Labrador and Golden Retrievers with confirmed medial coronoid process disease. Purebred Labrador and Golden Retrievers (n = 143, 206 elbows) without and with confirmed medial coronoid process disease were included. The prevalence of medial coronoid process disease in lame large breed dogs was calculated. Mediolateral and craniocaudal radiographs of elbows were analyzed to assess the medial coronoid process length and morphology, and subtrochlear-ulnar width. Mean grayscale value was calculated for radial and subtrochlear-ulnar zones. The prevalence of medial coronoid process disease was 20.8%. Labrador and Golden Retrievers were the most affected purebred dogs (29.6%). Elbows with confirmed medial coronoid process disease had short (P < 0.0001) and deformed (∼95%) medial coronoid process, with associated medial coronoid process osteophytosis (7.5%). Subtrochlear-ulnar sclerosis was evidenced in ∼96% of diseased elbows, with a significant increase (P < 0.0001) in subtrochlear-ulnar width and standardized grayscale value. Radial grayscale value did not differ between groups. Periarticular osteophytosis was identified in 51.4% of elbows with medial coronoid process disease. Medial coronoid process length and morphology, and subtrochlear-ulnar width and standardized grayscale value varied significantly in dogs with confirmed medial coronoid process disease compared to controls. Findings indicated that medial coronoid process disease has a high prevalence in lame large breed dogs and that quantitative radiographic assessments can contribute to the diagnosis. © 2018 American College of Veterinary Radiology.

The role of rational and experiential processing in influencing the framing effect.

PubMed

Stark, Emily; Baldwin, Austin S; Hertel, Andrew W; Rothman, Alexander J

2017-01-01

Research on individual differences and the framing effect has focused primarily on how variability in rational processing influences choice. However, we propose that measuring only rational processing presents an incomplete picture of how participants are responding to framed options, as orthogonal individual differences in experiential processing might be relevant. In two studies, we utilize the Rational Experiential Inventory, which captures individual differences in rational and experiential processing, to investigate how both processing types influence decisions. Our results show that differences in experiential processing, but not rational processing, moderated the effect of frame on choice. We suggest that future research should more closely examine the influence of experiential processing on making decisions, to gain a broader understanding of the conditions that contribute to the framing effect.

Study and Analysis of The Robot-Operated Material Processing Systems (ROMPS)

NASA Technical Reports Server (NTRS)

Nguyen, Charles C.

1996-01-01

This is a report presenting the progress of a research grant funded by NASA for work performed during 1 Oct. 1994 - 31 Sep. 1995. The report deals with the development and investigation of potential use of software for data processing for the Robot Operated Material Processing System (ROMPS). It reports on the progress of data processing of calibration samples processed by ROMPS in space and on earth. First data were retrieved using the I/O software and manually processed using MicroSoft Excel. Then the data retrieval and processing process was automated using a program written in C which is able to read the telemetry data and produce plots of time responses of sample temperatures and other desired variables. LabView was also employed to automatically retrieve and process the telemetry data.

Application of statistical process control and process capability analysis procedures in orbiter processing activities at the Kennedy Space Center

NASA Technical Reports Server (NTRS)

Safford, Robert R.; Jackson, Andrew E.; Swart, William W.; Barth, Timothy S.

1994-01-01

Successful ground processing at KSC requires that flight hardware and ground support equipment conform to specifications at tens of thousands of checkpoints. Knowledge of conformance is an essential requirement for launch. That knowledge of conformance at every requisite point does not, however, enable identification of past problems with equipment, or potential problem areas. This paper describes how the introduction of Statistical Process Control and Process Capability Analysis identification procedures into existing shuttle processing procedures can enable identification of potential problem areas and candidates for improvements to increase processing performance measures. Results of a case study describing application of the analysis procedures to Thermal Protection System processing are used to illustrate the benefits of the approaches described in the paper.

Separate cortical networks involved in music perception: preliminary functional MRI evidence for modularity of music processing.

PubMed

Schmithorst, Vincent J

2005-04-01

Music perception is a quite complex cognitive task, involving the perception and integration of various elements including melody, harmony, pitch, rhythm, and timbre. A preliminary functional MRI investigation of music perception was performed, using a simplified passive listening task. Group independent component analysis (ICA) was used to separate out various components involved in music processing, as the hemodynamic responses are not known a priori. Various components consistent with auditory processing, expressive language, syntactic processing, and visual association were found. The results are discussed in light of various hypotheses regarding modularity of music processing and its overlap with language processing. The results suggest that, while some networks overlap with ones used for language processing, music processing may involve its own domain-specific processing subsystems.

Industrial implementation of spatial variability control by real-time SPC

NASA Astrophysics Data System (ADS)

Roule, O.; Pasqualini, F.; Borde, M.

2016-10-01

Advanced technology nodes require more and more information to get the wafer process well setup. The critical dimension of components decreases following Moore's law. At the same time, the intra-wafer dispersion linked to the spatial non-uniformity of tool's processes is not capable to decrease in the same proportions. APC systems (Advanced Process Control) are being developed in waferfab to automatically adjust and tune wafer processing, based on a lot of process context information. It can generate and monitor complex intrawafer process profile corrections between different process steps. It leads us to put under control the spatial variability, in real time by our SPC system (Statistical Process Control). This paper will outline the architecture of an integrated process control system for shape monitoring in 3D, implemented in waferfab.

Modeling and analysis of power processing systems: Feasibility investigation and formulation of a methodology

NASA Technical Reports Server (NTRS)

Biess, J. J.; Yu, Y.; Middlebrook, R. D.; Schoenfeld, A. D.

1974-01-01

A review is given of future power processing systems planned for the next 20 years, and the state-of-the-art of power processing design modeling and analysis techniques used to optimize power processing systems. A methodology of modeling and analysis of power processing equipment and systems has been formulated to fulfill future tradeoff studies and optimization requirements. Computer techniques were applied to simulate power processor performance and to optimize the design of power processing equipment. A program plan to systematically develop and apply the tools for power processing systems modeling and analysis is presented so that meaningful results can be obtained each year to aid the power processing system engineer and power processing equipment circuit designers in their conceptual and detail design and analysis tasks.

Laser displacement sensor to monitor the layup process of composite laminate production

NASA Astrophysics Data System (ADS)

Miesen, Nick; Groves, Roger M.; Sinke, Jos; Benedictus, Rinze

2013-04-01

Several types of flaw can occur during the layup process of prepreg composite laminates. Quality control after the production process checks the end product by testing the specimens for flaws which are included during the layup process or curing process, however by then these flaws are already irreversibly embedded in the laminate. This paper demonstrates the use of a laser displacement sensor technique applied during the layup process of prepreg laminates for in-situ flaw detection, for typical flaws that can occur during the composite production process. An incorrect number of layers and fibre wrinkling are dominant flaws during the process of layup. These and other dominant flaws have been modeled to determine the requirements for an in-situ monitoring during the layup process of prepreg laminates.

Levels of integration in cognitive control and sequence processing in the prefrontal cortex.

PubMed

Bahlmann, Jörg; Korb, Franziska M; Gratton, Caterina; Friederici, Angela D

2012-01-01

Cognitive control is necessary to flexibly act in changing environments. Sequence processing is needed in language comprehension to build the syntactic structure in sentences. Functional imaging studies suggest that sequence processing engages the left ventrolateral prefrontal cortex (PFC). In contrast, cognitive control processes additionally recruit bilateral rostral lateral PFC regions. The present study aimed to investigate these two types of processes in one experimental paradigm. Sequence processing was manipulated using two different sequencing rules varying in complexity. Cognitive control was varied with different cue-sets that determined the choice of a sequencing rule. Univariate analyses revealed distinct PFC regions for the two types of processing (i.e. sequence processing: left ventrolateral PFC and cognitive control processing: bilateral dorsolateral and rostral PFC). Moreover, in a common brain network (including left lateral PFC and intraparietal sulcus) no interaction between sequence and cognitive control processing was observed. In contrast, a multivariate pattern analysis revealed an interaction of sequence and cognitive control processing, such that voxels in left lateral PFC and parietal cortex showed different tuning functions for tasks involving different sequencing and cognitive control demands. These results suggest that the difference between the process of rule selection (i.e. cognitive control) and the process of rule-based sequencing (i.e. sequence processing) find their neuronal underpinnings in distinct activation patterns in lateral PFC. Moreover, the combination of rule selection and rule sequencing can shape the response of neurons in lateral PFC and parietal cortex.

Levels of Integration in Cognitive Control and Sequence Processing in the Prefrontal Cortex

PubMed Central

Bahlmann, Jörg; Korb, Franziska M.; Gratton, Caterina; Friederici, Angela D.

2012-01-01

Cognitive control is necessary to flexibly act in changing environments. Sequence processing is needed in language comprehension to build the syntactic structure in sentences. Functional imaging studies suggest that sequence processing engages the left ventrolateral prefrontal cortex (PFC). In contrast, cognitive control processes additionally recruit bilateral rostral lateral PFC regions. The present study aimed to investigate these two types of processes in one experimental paradigm. Sequence processing was manipulated using two different sequencing rules varying in complexity. Cognitive control was varied with different cue-sets that determined the choice of a sequencing rule. Univariate analyses revealed distinct PFC regions for the two types of processing (i.e. sequence processing: left ventrolateral PFC and cognitive control processing: bilateral dorsolateral and rostral PFC). Moreover, in a common brain network (including left lateral PFC and intraparietal sulcus) no interaction between sequence and cognitive control processing was observed. In contrast, a multivariate pattern analysis revealed an interaction of sequence and cognitive control processing, such that voxels in left lateral PFC and parietal cortex showed different tuning functions for tasks involving different sequencing and cognitive control demands. These results suggest that the difference between the process of rule selection (i.e. cognitive control) and the process of rule-based sequencing (i.e. sequence processing) find their neuronal underpinnings in distinct activation patterns in lateral PFC. Moreover, the combination of rule selection and rule sequencing can shape the response of neurons in lateral PFC and parietal cortex. PMID:22952762

Flow chemistry using milli- and microstructured reactors-from conventional to novel process windows.

PubMed

Illg, Tobias; Löb, Patrick; Hessel, Volker

2010-06-01

The terminology Novel Process Window unites different methods to improve existing processes by applying unconventional and harsh process conditions like: process routes at much elevated pressure, much elevated temperature, or processing in a thermal runaway regime to achieve a significant impact on process performance. This paper is a review of parts of IMM's works in particular the applicability of above mentioned Novel Process Windows on selected chemical reactions. First, general characteristics of microreactors are discussed like excellent mass and heat transfer and improved mixing quality. Different types of reactions are presented in which the use of microstructured devices led to an increased process performance by applying Novel Process Windows. These examples were chosen to demonstrate how chemical reactions can benefit from the use of milli- and microstructured devices and how existing protocols can be changed toward process conditions hitherto not applicable in standard laboratory equipment. The used milli- and microstructured reactors can also offer advantages in other areas, for example, high-throughput screening of catalysts and better control of size distribution in a particle synthesis process by improved mixing, etc. The chemical industry is under continuous improvement. So, a lot of research is being done to synthesize high value chemicals, to optimize existing processes in view of process safety and energy consumption and to search for new routes to produce such chemicals. Leitmotifs of such undertakings are often sustainable development(1) and Green Chemistry(2).

Fast but fleeting: adaptive motor learning processes associated with aging and cognitive decline.

PubMed

Trewartha, Kevin M; Garcia, Angeles; Wolpert, Daniel M; Flanagan, J Randall

2014-10-01

Motor learning has been shown to depend on multiple interacting learning processes. For example, learning to adapt when moving grasped objects with novel dynamics involves a fast process that adapts and decays quickly-and that has been linked to explicit memory-and a slower process that adapts and decays more gradually. Each process is characterized by a learning rate that controls how strongly motor memory is updated based on experienced errors and a retention factor determining the movement-to-movement decay in motor memory. Here we examined whether fast and slow motor learning processes involved in learning novel dynamics differ between younger and older adults. In addition, we investigated how age-related decline in explicit memory performance influences learning and retention parameters. Although the groups adapted equally well, they did so with markedly different underlying processes. Whereas the groups had similar fast processes, they had different slow processes. Specifically, the older adults exhibited decreased retention in their slow process compared with younger adults. Within the older group, who exhibited considerable variation in explicit memory performance, we found that poor explicit memory was associated with reduced retention in the fast process, as well as the slow process. These findings suggest that explicit memory resources are a determining factor in impairments in the both the fast and slow processes for motor learning but that aging effects on the slow process are independent of explicit memory declines. Copyright © 2014 the authors 0270-6474/14/3413411-11$15.00/0.

Parallel Activation in Bilingual Phonological Processing

ERIC Educational Resources Information Center

Lee, Su-Yeon

2011-01-01

In bilingual language processing, the parallel activation hypothesis suggests that bilinguals activate their two languages simultaneously during language processing. Support for the parallel activation mainly comes from studies of lexical (word-form) processing, with relatively less attention to phonological (sound) processing. According to…

OCLC-MARC Tape Processing: A Functional Analysis.

ERIC Educational Resources Information Center

Miller, Bruce Cummings

1984-01-01

Analyzes structure of, and data in, the OCLC-MARC record in the form delivered via OCLC's Tape Subscription Service, and outlines important processing functions involved: "unreadable tapes," duplicate records and deduping, match processing, choice processing, locations processing, "automatic" and "input" stamps,…

7 Processes that Enable NASA Software Engineering Technologies: Value-Added Process Engineering

NASA Technical Reports Server (NTRS)

Housch, Helen; Godfrey, Sally

2011-01-01

The presentation reviews Agency process requirements and the purpose, benefits, and experiences or seven software engineering processes. The processes include: product integration, configuration management, verification, software assurance, measurement and analysis, requirements management, and planning and monitoring.

Risk-based Strategy to Determine Testing Requirement for the Removal of Residual Process Reagents as Process-related Impurities in Bioprocesses.

PubMed

Qiu, Jinshu; Li, Kim; Miller, Karen; Raghani, Anil

2015-01-01

The purpose of this article is to recommend a risk-based strategy for determining clearance testing requirements of the process reagents used in manufacturing biopharmaceutical products. The strategy takes account of four risk factors. Firstly, the process reagents are classified into two categories according to their safety profile and history of use: generally recognized as safe (GRAS) and potential safety concern (PSC) reagents. The clearance testing of GRAS reagents can be eliminated because of their safe use historically and process capability to remove these reagents. An estimated safety margin (Se) value, a ratio of the exposure limit to the estimated maximum reagent amount, is then used to evaluate the necessity for testing the PSC reagents at an early development stage. The Se value is calculated from two risk factors, the starting PSC reagent amount per maximum product dose (Me), and the exposure limit (Le). A worst-case scenario is assumed to estimate the Me value, that is common. The PSC reagent of interest is co-purified with the product and no clearance occurs throughout the entire purification process. No clearance testing is required for this PSC reagent if its Se value is ≥1; otherwise clearance testing is needed. Finally, the point of the process reagent introduction to the process is also considered in determining the necessity of the clearance testing for process reagents. How to use the measured safety margin as a criterion for determining PSC reagent testing at process characterization, process validation, and commercial production stages are also described. A large number of process reagents are used in the biopharmaceutical manufacturing to control the process performance. Clearance testing for all of the process reagents will be an enormous analytical task. In this article, a risk-based strategy is described to eliminate unnecessary clearance testing for majority of the process reagents using four risk factors. The risk factors included in the strategy are (i) safety profile of the reagents, (ii) the starting amount of the process reagents used in the manufacturing process, (iii) the maximum dose of the product, and (iv) the point of introduction of the process reagents in the process. The implementation of the risk-based strategy can eliminate clearance testing for approximately 90% of the process reagents used in the manufacturing processes. This science-based strategy allows us to ensure patient safety and meet regulatory agency expectations throughout the product development life cycle. © PDA, Inc. 2015.

Titania nanotube powders obtained by rapid breakdown anodization in perchloric acid electrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ali, Saima, E-mail: saima.ali@aalto.fi; Hannula, Simo-Pekka

Titania nanotube (TNT) powders are prepared by rapid break down anodization (RBA) in a 0.1 M perchloric acid (HClO{sub 4}) solution (Process 1), and ethylene glycol (EG) mixture with HClO{sub 4} and water (Process 2). A study of the as-prepared and calcined TNT powders obtained by both processes is implemented to evaluate and compare the morphology, crystal structure, specific surface area, and the composition of the nanotubes. Longer TNTs are formed in Process 1, while comparatively larger pore diameter and wall thickness are obtained for the nanotubes prepared by Process 2. The TNTs obtained by Process 1 are converted tomore » nanorods at 350 °C, while nanotubes obtained by Process 2 preserve tubular morphology till 350 °C. In addition, the TNTs prepared by an aqueous electrolyte have a crystalline structure, whereas the TNTs obtained by Process 2 are amorphous. Samples calcined till 450 °C have XRD peaks from the anatase phase, while the rutile phase appears at 550 °C for the TNTs prepared by both processes. The Raman spectra also show clear anatase peaks for all samples except the as-prepared sample obtained by Process 2, thus supporting the XRD findings. FTIR spectra reveal the presence of O-H groups in the structure for the TNTs obtained by both processes. However, the presence is less prominent for annealed samples. Additionally, TNTs obtained by Process 2 have a carbonaceous impurity present in the structure attributed to the electrolyte used in that process. While a negligible weight loss is typical for TNTs prepared from aqueous electrolytes, a weight loss of 38.6% in the temperature range of 25–600 °C is found for TNTs prepared in EG electrolyte (Process 2). A large specific surface area of 179.2 m{sup 2} g{sup −1} is obtained for TNTs prepared by Process 1, whereas Process 2 produces nanotubes with a lower specific surface area. The difference appears to correspond to the dimensions of the nanotubes obtained by the two processes. - Graphical abstract: Titania nanotube powders prepared by Process 1 and Process 2 have different crystal structure and specific surface area. - Highlights: • Titania nanotube (TNT) powder is prepared in low water organic electrolyte. • Characterization of TNT powders prepared from aqueous and organic electrolyte. • TNTs prepared by Process 1 are crystalline with higher specific surface area. • TNTs obtained by Process 2 have carbonaceous impurities in the structure.« less

A processing approach to the working memory/long-term memory distinction: evidence from the levels-of-processing span task.

PubMed

Rose, Nathan S; Craik, Fergus I M

2012-07-01

Recent theories suggest that performance on working memory (WM) tasks involves retrieval from long-term memory (LTM). To examine whether WM and LTM tests have common principles, Craik and Tulving's (1975) levels-of-processing paradigm, which is known to affect LTM, was administered as a WM task: Participants made uppercase, rhyme, or category-membership judgments about words, and immediate recall of the words was required after every 3 or 8 processing judgments. In Experiment 1, immediate recall did not demonstrate a levels-of-processing effect, but a subsequent LTM test (delayed recognition) of the same words did show a benefit of deeper processing. Experiment 2 showed that surprise immediate recall of 8-item lists did demonstrate a levels-of-processing effect, however. A processing account of the conditions in which levels-of-processing effects are and are not found in WM tasks was advanced, suggesting that the extent to which levels-of-processing effects are similar between WM and LTM tests largely depends on the amount of disruption to active maintenance processes. 2012 APA, all rights reserved

Emotional words can be embodied or disembodied: the role of superficial vs. deep types of processing

PubMed Central

Abbassi, Ensie; Blanchette, Isabelle; Ansaldo, Ana I.; Ghassemzadeh, Habib; Joanette, Yves

2015-01-01

Emotional words are processed rapidly and automatically in the left hemisphere (LH) and slowly, with the involvement of attention, in the right hemisphere (RH). This review aims to find the reason for this difference and suggests that emotional words can be processed superficially or deeply due to the involvement of the linguistic and imagery systems, respectively. During superficial processing, emotional words likely make connections only with semantically associated words in the LH. This part of the process is automatic and may be sufficient for the purpose of language processing. Deep processing, in contrast, seems to involve conceptual information and imagery of a word’s perceptual and emotional properties using autobiographical memory contents. Imagery and the involvement of autobiographical memory likely differentiate between emotional and neutral word processing and explain the salient role of the RH in emotional word processing. It is concluded that the level of emotional word processing in the RH should be deeper than in the LH and, thus, it is conceivable that the slow mode of processing adds certain qualities to the output. PMID:26217288

Process Monitoring Evaluation and Implementation for the Wood Abrasive Machining Process

PubMed Central

Saloni, Daniel E.; Lemaster, Richard L.; Jackson, Steven D.

2010-01-01

Wood processing industries have continuously developed and improved technologies and processes to transform wood to obtain better final product quality and thus increase profits. Abrasive machining is one of the most important of these processes and therefore merits special attention and study. The objective of this work was to evaluate and demonstrate a process monitoring system for use in the abrasive machining of wood and wood based products. The system developed increases the life of the belt by detecting (using process monitoring sensors) and removing (by cleaning) the abrasive loading during the machining process. This study focused on abrasive belt machining processes and included substantial background work, which provided a solid base for understanding the behavior of the abrasive, and the different ways that the abrasive machining process can be monitored. In addition, the background research showed that abrasive belts can effectively be cleaned by the appropriate cleaning technique. The process monitoring system developed included acoustic emission sensors which tended to be sensitive to belt wear, as well as platen vibration, but not loading, and optical sensors which were sensitive to abrasive loading. PMID:22163477

Adaptive memory: determining the proximate mechanisms responsible for the memorial advantages of survival processing.

PubMed

Burns, Daniel J; Burns, Sarah A; Hwang, Ana J

2011-01-01

J. S. Nairne, S. R. Thompson, and J. N. S. Pandeirada (2007) suggested that our memory systems may have evolved to help us remember fitness-relevant information and showed that retention of words rated for their relevance to survival is superior to that of words encoded under other deep processing conditions. The authors present 4 experiments that uncover the proximate mechanisms likely responsible. The authors obtained a recall advantage for survival processing compared with conditions that promoted only item-specific processing or only relational processing. This effect was eliminated when control conditions encouraged both item-specific and relational processing. Data from separate measures of item-specific and relational processing generally were consistent with the view that the memorial advantage for survival processing results from the encoding of both types of processing. Although the present study suggests the proximate mechanisms for the effect, the authors argue that survival processing may be fundamentally different from other memory phenomena for which item-specific and relational processing differences have been implicated. (PsycINFO Database Record (c) 2010 APA, all rights reserved).

Implementation of quality by design toward processing of food products.

PubMed

Rathore, Anurag S; Kapoor, Gautam

2017-05-28

Quality by design (QbD) is a systematic approach that begins with predefined objectives and emphasizes product and process understanding and process control. It is an approach based on principles of sound science and quality risk management. As the food processing industry continues to embrace the idea of in-line, online, and/or at-line sensors and real-time characterization for process monitoring and control, the existing gaps with regard to our ability to monitor multiple parameters/variables associated with the manufacturing process will be alleviated over time. Investments made for development of tools and approaches that facilitate high-throughput analytical and process development, process analytical technology, design of experiments, risk analysis, knowledge management, and enhancement of process/product understanding would pave way for operational and economic benefits later in the commercialization process and across other product pipelines. This article aims to achieve two major objectives. First, to review the progress that has been made in the recent years on the topic of QbD implementation in processing of food products and second, present a case study that illustrates benefits of such QbD implementation.

Energy saving processes for nitrogen removal in organic wastewater from food processing industries in Thailand.

PubMed

Johansen, N H; Suksawad, N; Balslev, P

2004-01-01

Nitrogen removal from organic wastewater is becoming a demand in developed communities. The use of nitrite as intermediate in the treatment of wastewater has been largely ignored, but is actually a relevant energy saving process compared to conventional nitrification/denitrification using nitrate as intermediate. Full-scale results and pilot-scale results using this process are presented. The process needs some additional process considerations and process control to be utilized. Especially under tropical conditions the nitritation process will round easily, and it must be expected that many AS treatment plants in the food industry already produce NO2-N. This uncontrolled nitrogen conversion can be the main cause for sludge bulking problems. It is expected that sludge bulking problems in many cases can be solved just by changing the process control in order to run a more consequent nitritation. Theoretically this process will decrease the oxygen consumption for oxidation by 25% and the use of carbon source for the reduction will be decreased by 40% compared to the conventional process.

Application of Ozone MBBR Process in Refinery Wastewater Treatment

NASA Astrophysics Data System (ADS)

Lin, Wang

2018-01-01

Moving Bed Biofilm Reactor (MBBR) is a kind of sewage treatment technology based on fluidized bed. At the same time, it can also be regarded as an efficient new reactor between active sludge method and the biological membrane method. The application of ozone MBBR process in refinery wastewater treatment is mainly studied. The key point is to design the ozone +MBBR combined process based on MBBR process. The ozone +MBBR process is used to analyze the treatment of concentrated water COD discharged from the refinery wastewater treatment plant. The experimental results show that the average removal rate of COD is 46.0%~67.3% in the treatment of reverse osmosis concentrated water by ozone MBBR process, and the effluent can meet the relevant standard requirements. Compared with the traditional process, the ozone MBBR process is more flexible. The investment of this process is mainly ozone generator, blower and so on. The prices of these items are relatively inexpensive, and these costs can be offset by the excess investment in traditional activated sludge processes. At the same time, ozone MBBR process has obvious advantages in water quality, stability and other aspects.

Models of recognition: A review of arguments in favor of a dual-process account

PubMed Central

DIANA, RACHEL A.; REDER, LYNNE M.; ARNDT, JASON; PARK, HEEKYEONG

2008-01-01

The majority of computationally specified models of recognition memory have been based on a single-process interpretation, claiming that familiarity is the only influence on recognition. There is increasing evidence that recognition is, in fact, based on two processes: recollection and familiarity. This article reviews the current state of the evidence for dual-process models, including the usefulness of the remember/know paradigm, and interprets the relevant results in terms of the source of activation confusion (SAC) model of memory. We argue that the evidence from each of the areas we discuss, when combined, presents a strong case that inclusion of a recollection process is necessary. Given this conclusion, we also argue that the dual-process claim that the recollection process is always available is, in fact, more parsimonious than the single-process claim that the recollection process is used only in certain paradigms. The value of a well-specified process model such as the SAC model is discussed with regard to other types of dual-process models. PMID:16724763

Emotional words can be embodied or disembodied: the role of superficial vs. deep types of processing.

PubMed

Abbassi, Ensie; Blanchette, Isabelle; Ansaldo, Ana I; Ghassemzadeh, Habib; Joanette, Yves

2015-01-01

Emotional words are processed rapidly and automatically in the left hemisphere (LH) and slowly, with the involvement of attention, in the right hemisphere (RH). This review aims to find the reason for this difference and suggests that emotional words can be processed superficially or deeply due to the involvement of the linguistic and imagery systems, respectively. During superficial processing, emotional words likely make connections only with semantically associated words in the LH. This part of the process is automatic and may be sufficient for the purpose of language processing. Deep processing, in contrast, seems to involve conceptual information and imagery of a word's perceptual and emotional properties using autobiographical memory contents. Imagery and the involvement of autobiographical memory likely differentiate between emotional and neutral word processing and explain the salient role of the RH in emotional word processing. It is concluded that the level of emotional word processing in the RH should be deeper than in the LH and, thus, it is conceivable that the slow mode of processing adds certain qualities to the output.

Techno-economic analysis of biocatalytic processes for production of alkene expoxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borole, Abhijeet P

2007-01-01

A techno-economic analysis of two different bioprocesses was conducted, one for the conversion of propylene to propylene oxide (PO) and other for conversion of styrene to styrene expoxide (SO). The first process was a lipase-mediated chemo-enzymatic reaction, whereas the second one was a one-step enzymatic process using chloroperoxidase. The PO produced through the chemo-enzymatic process is a racemic product, whereas the latter process (based on chloroperoxidase) produces an enantio-pure product. The former process thus falls under the category of high-volume commodity chemical (PO); whereas the latter is a low-volume, high-value product (SO).A simulation of the process was conducted using themore » bioprocess engineering software SuperPro Designer v6.0 (Intelligen, Inc., Scotch Plains, NJ) to determine the economic feasibility of the process. The purpose of the exercise was to compare biocatalytic processes with existing chemical processes for production of alkene expoxides. The results show that further improvements are needed in improving biocatalyst stability to make these bioprocesses competitive with chemical processes.« less

The representation of conceptual knowledge: visual, auditory, and olfactory imagery compared with semantic processing.

PubMed

Palmiero, Massimiliano; Di Matteo, Rosalia; Belardinelli, Marta Olivetti

2014-05-01

Two experiments comparing imaginative processing in different modalities and semantic processing were carried out to investigate the issue of whether conceptual knowledge can be represented in different format. Participants were asked to judge the similarity between visual images, auditory images, and olfactory images in the imaginative block, if two items belonged to the same category in the semantic block. Items were verbally cued in both experiments. The degree of similarity between the imaginative and semantic items was changed across experiments. Experiment 1 showed that the semantic processing was faster than the visual and the auditory imaginative processing, whereas no differentiation was possible between the semantic processing and the olfactory imaginative processing. Experiment 2 revealed that only the visual imaginative processing could be differentiated from the semantic processing in terms of accuracy. These results showed that the visual and auditory imaginative processing can be differentiated from the semantic processing, although both visual and auditory images strongly rely on semantic representations. On the contrary, no differentiation is possible within the olfactory domain. Results are discussed in the frame of the imagery debate.

Working memory load eliminates the survival processing effect.

PubMed

Kroneisen, Meike; Rummel, Jan; Erdfelder, Edgar

2014-01-01

In a series of experiments, Nairne, Thompson, and Pandeirada (2007) demonstrated that words judged for their relevance to a survival scenario are remembered better than words judged for a scenario not relevant on a survival dimension. They explained this survival-processing effect by arguing that nature "tuned" our memory systems to process and remember fitness-relevant information. Kroneisen and Erdfelder (2011) proposed that it may not be survival processing per se that facilitates recall but the richness and distinctiveness with which information is encoded. To further test this account, we investigated how the survival processing effect is affected by cognitive load. If the survival processing effect is due to automatic processes or, alternatively, if survival processing is routinely prioritized in dual-task contexts, we would expect this effect to persist under cognitive load conditions. If the effect relies on cognitively demanding processes like richness and distinctiveness of encoding, however, the survival processing benefit should be hampered by increased cognitive load during encoding. Results were in line with the latter prediction, that is, the survival processing effect vanished under dual-task conditions.

E-learning process maturity level: a conceptual framework

NASA Astrophysics Data System (ADS)

Rahmah, A.; Santoso, H. B.; Hasibuan, Z. A.

2018-03-01

ICT advancement is a sure thing with the impact influencing many domains, including learning in both formal and informal situations. It leads to a new mindset that we should not only utilize the given ICT to support the learning process, but also improve it gradually involving a lot of factors. These phenomenon is called e-learning process evolution. Accordingly, this study attempts to explore maturity level concept to provide the improvement direction gradually and progression monitoring for the individual e-learning process. Extensive literature review, observation, and forming constructs are conducted to develop a conceptual framework for e-learning process maturity level. The conceptual framework consists of learner, e-learning process, continuous improvement, evolution of e-learning process, technology, and learning objectives. Whilst, evolution of e-learning process depicted as current versus expected conditions of e-learning process maturity level. The study concludes that from the e-learning process maturity level conceptual framework, it may guide the evolution roadmap for e-learning process, accelerate the evolution, and decrease the negative impact of ICT. The conceptual framework will be verified and tested in the future study.

Heat input and accumulation for ultrashort pulse processing with high average power

NASA Astrophysics Data System (ADS)

Finger, Johannes; Bornschlegel, Benedikt; Reininghaus, Martin; Dohrn, Andreas; Nießen, Markus; Gillner, Arnold; Poprawe, Reinhart

2018-05-01

Materials processing using ultrashort pulsed laser radiation with pulse durations <10 ps is known to enable very precise processing with negligible thermal load. However, even for the application of picosecond and femtosecond laser radiation, not the full amount of the absorbed energy is converted into ablation products and a distinct fraction of the absorbed energy remains as residual heat in the processed workpiece. For low average power and power densities, this heat is usually not relevant for the processing results and dissipates into the workpiece. In contrast, when higher average powers and repetition rates are applied to increase the throughput and upscale ultrashort pulse processing, this heat input becomes relevant and significantly affects the achieved processing results. In this paper, we outline the relevance of heat input for ultrashort pulse processing, starting with the heat input of a single ultrashort laser pulse. Heat accumulation during ultrashort pulse processing with high repetition rate is discussed as well as heat accumulation for materials processing using pulse bursts. In addition, the relevance of heat accumulation with multiple scanning passes and processing with multiple laser spots is shown.

Defining and reconstructing clinical processes based on IHE and BPMN 2.0.

PubMed

Strasser, Melanie; Pfeifer, Franz; Helm, Emmanuel; Schuler, Andreas; Altmann, Josef

2011-01-01

This paper describes the current status and the results of our process management system for defining and reconstructing clinical care processes, which contributes to compare, analyze and evaluate clinical processes and further to identify high cost tasks or stays. The system is founded on IHE, which guarantees standardized interfaces and interoperability between clinical information systems. At the heart of the system there is BPMN, a modeling notation and specification language, which allows the definition and execution of clinical processes. The system provides functionality to define healthcare information system independent clinical core processes and to execute the processes in a workflow engine. Furthermore, the reconstruction of clinical processes is done by evaluating an IHE audit log database, which records patient movements within a health care facility. The main goal of the system is to assist hospital operators and clinical process managers to detect discrepancies between defined and actual clinical processes and as well to identify main causes of high medical costs. Beyond that, the system can potentially contribute to reconstruct and improve clinical processes and enhance cost control and patient care quality.

Process qualification and testing of LENS deposited AY1E0125 D-bottle brackets.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Atwood, Clinton J.; Smugeresky, John E.; Jew, Michael

2006-11-01

The LENS Qualification team had the goal of performing a process qualification for the Laser Engineered Net Shaping{trademark}(LENS{reg_sign}) process. Process Qualification requires that a part be selected for process demonstration. The AY1E0125 D-Bottle Bracket from the W80-3 was selected for this work. The repeatability of the LENS process was baselined to determine process parameters. Six D-Bottle brackets were deposited using LENS, machined to final dimensions, and tested in comparison to conventionally processed brackets. The tests, taken from ES1E0003, included a mass analysis and structural dynamic testing including free-free and assembly-level modal tests, and Haversine shock tests. The LENS brackets performedmore » with very similar characteristics to the conventionally processed brackets. Based on the results of the testing, it was concluded that the performance of the brackets made them eligible for parallel path testing in subsystem level tests. The testing results and process rigor qualified the LENS process as detailed in EER200638525A.« less

Sustainability assessment of shielded metal arc welding (SMAW) process

NASA Astrophysics Data System (ADS)

Alkahla, Ibrahim; Pervaiz, Salman

2017-09-01

Shielded metal arc welding (SMAW) process is one of the most commonly employed material joining processes utilized in the various industrial sectors such as marine, ship-building, automotive, aerospace, construction and petrochemicals etc. The increasing pressure on manufacturing sector wants the welding process to be sustainable in nature. The SMAW process incorporates several types of inputs and output streams. The sustainability concerns associated with SMAW process are linked with the various input and output streams such as electrical energy requirement, input material consumptions, slag formation, fumes emission and hazardous working conditions associated with the human health and occupational safety. To enhance the environmental performance of the SMAW welding process, there is a need to characterize the sustainability for the SMAW process under the broad framework of sustainability. Most of the available literature focuses on the technical and economic aspects of the welding process, however the environmental and social aspects are rarely addressed. The study reviews SMAW process with respect to the triple bottom line (economic, environmental and social) sustainability approach. Finally, the study concluded recommendations towards achieving economical and sustainable SMAW welding process.

Decontamination and disposal of PCB wastes.

PubMed Central

Johnston, L E

1985-01-01

Decontamination and disposal processes for PCB wastes are reviewed. Processes are classed as incineration, chemical reaction or decontamination. Incineration technologies are not limited to the rigorous high temperature but include those where innovations in use of oxident, heat transfer and residue recycle are made. Chemical processes include the sodium processes, radiant energy processes and low temperature oxidations. Typical processing rates and associated costs are provided where possible. PMID:3928363

Logistics Control Facility: A Normative Model for Total Asset Visibility in the Air Force Logistics System

DTIC Science & Technology

1994-09-01

IIssue Computers, information systems, and communication systems are being increasingly used in transportation, warehousing, order processing , materials...inventory levels, reduced order processing times, reduced order processing costs, and increased customer satisfaction. While purchasing and transportation...process, the speed in which crders are processed would increase significantly. Lowering the order processing time in turn lowers the lead time, which in

Definition and documentation of engineering processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDonald, G.W.

1997-11-01

This tutorial is an extract of a two-day workshop developed under the auspices of the Quality Engineering Department at Sandia National Laboratories. The presentation starts with basic definitions and addresses why processes should be defined and documented. It covers three primary topics: (1) process considerations and rationale, (2) approach to defining and documenting engineering processes, and (3) an IDEFO model of the process for defining engineering processes.

Method for enhanced atomization of liquids

DOEpatents

Thompson, Richard E.; White, Jerome R.

1993-01-01

In a process for atomizing a slurry or liquid process stream in which a slurry or liquid is passed through a nozzle to provide a primary atomized process stream, an improvement which comprises subjecting the liquid or slurry process stream to microwave energy as the liquid or slurry process stream exits the nozzle, wherein sufficient microwave heating is provided to flash vaporize the primary atomized process stream.

Rethinking a Negative Event: The Affective Impact of Ruminative versus Imagery-Based Processing of Aversive Autobiographical Memories.

PubMed

Slofstra, Christien; Eisma, Maarten C; Holmes, Emily A; Bockting, Claudi L H; Nauta, Maaike H

2017-01-01

Ruminative (abstract verbal) processing during recall of aversive autobiographical memories may serve to dampen their short-term affective impact. Experimental studies indeed demonstrate that verbal processing of non-autobiographical material and positive autobiographical memories evokes weaker affective responses than imagery-based processing. In the current study, we hypothesized that abstract verbal or concrete verbal processing of an aversive autobiographical memory would result in weaker affective responses than imagery-based processing. The affective impact of abstract verbal versus concrete verbal versus imagery-based processing during recall of an aversive autobiographical memory was investigated in a non-clinical sample ( n  = 99) using both an observational and an experimental design. Observationally, it was examined whether spontaneous use of processing modes (both state and trait measures) was associated with impact of aversive autobiographical memory recall on negative and positive affect. Experimentally, the causal relation between processing modes and affective impact was investigated by manipulating the processing mode during retrieval of the same aversive autobiographical memory. Main findings were that higher levels of trait (but not state) measures of both ruminative and imagery-based processing and depressive symptomatology were positively correlated with higher levels of negative affective impact in the observational part of the study. In the experimental part, no main effect of processing modes on affective impact of autobiographical memories was found. However, a significant moderating effect of depressive symptomatology was found. Only for individuals with low levels of depressive symptomatology, concrete verbal (but not abstract verbal) processing of the aversive autobiographical memory did result in weaker affective responses, compared to imagery-based processing. These results cast doubt on the hypothesis that ruminative processing of aversive autobiographical memories serves to avoid the negative emotions evoked by such memories. Furthermore, findings suggest that depressive symptomatology is associated with the spontaneous use and the affective impact of processing modes during recall of aversive autobiographical memories. Clinical studies are needed that examine the role of processing modes during aversive autobiographical memory recall in depression, including the potential effectiveness of targeting processing modes in therapy.

Active pharmaceutical ingredient (API) production involving continuous processes--a process system engineering (PSE)-assisted design framework.

PubMed

Cervera-Padrell, Albert E; Skovby, Tommy; Kiil, Søren; Gani, Rafiqul; Gernaey, Krist V

2012-10-01

A systematic framework is proposed for the design of continuous pharmaceutical manufacturing processes. Specifically, the design framework focuses on organic chemistry based, active pharmaceutical ingredient (API) synthetic processes, but could potentially be extended to biocatalytic and fermentation-based products. The method exploits the synergic combination of continuous flow technologies (e.g., microfluidic techniques) and process systems engineering (PSE) methods and tools for faster process design and increased process understanding throughout the whole drug product and process development cycle. The design framework structures the many different and challenging design problems (e.g., solvent selection, reactor design, and design of separation and purification operations), driving the user from the initial drug discovery steps--where process knowledge is very limited--toward the detailed design and analysis. Examples from the literature of PSE methods and tools applied to pharmaceutical process design and novel pharmaceutical production technologies are provided along the text, assisting in the accumulation and interpretation of process knowledge. Different criteria are suggested for the selection of batch and continuous processes so that the whole design results in low capital and operational costs as well as low environmental footprint. The design framework has been applied to the retrofit of an existing batch-wise process used by H. Lundbeck A/S to produce an API: zuclopenthixol. Some of its batch operations were successfully converted into continuous mode, obtaining higher yields that allowed a significant simplification of the whole process. The material and environmental footprint of the process--evaluated through the process mass intensity index, that is, kg of material used per kg of product--was reduced to half of its initial value, with potential for further reduction. The case-study includes reaction steps typically used by the pharmaceutical industry featuring different characteristic reaction times, as well as L-L separation and distillation-based solvent exchange steps, and thus constitutes a good example of how the design framework can be useful to efficiently design novel or already existing API manufacturing processes taking advantage of continuous processes. Copyright © 2012 Elsevier B.V. All rights reserved.

On the facilitative effects of face motion on face recognition and its development

PubMed Central

Xiao, Naiqi G.; Perrotta, Steve; Quinn, Paul C.; Wang, Zhe; Sun, Yu-Hao P.; Lee, Kang

2014-01-01

For the past century, researchers have extensively studied human face processing and its development. These studies have advanced our understanding of not only face processing, but also visual processing in general. However, most of what we know about face processing was investigated using static face images as stimuli. Therefore, an important question arises: to what extent does our understanding of static face processing generalize to face processing in real-life contexts in which faces are mostly moving? The present article addresses this question by examining recent studies on moving face processing to uncover the influence of facial movements on face processing and its development. First, we describe evidence on the facilitative effects of facial movements on face recognition and two related theoretical hypotheses: the supplementary information hypothesis and the representation enhancement hypothesis. We then highlight several recent studies suggesting that facial movements optimize face processing by activating specific face processing strategies that accommodate to task requirements. Lastly, we review the influence of facial movements on the development of face processing in the first year of life. We focus on infants' sensitivity to facial movements and explore the facilitative effects of facial movements on infants' face recognition performance. We conclude by outlining several future directions to investigate moving face processing and emphasize the importance of including dynamic aspects of facial information to further understand face processing in real-life contexts. PMID:25009517

Comparison of property between two Viking Seismic tapes

NASA Astrophysics Data System (ADS)

Yamamoto, Y.; Yamada, R.

2016-12-01

Tthe restoration work of the seismometer data onboard Viking Lander 2 is still continuing. Originally, the data were processed and archived both in MIT and UTIG separately, and each data is accessible via the Internet today. Their file formats to store the data are different, but both of them are currently readable due to the continuous investigation. However, there is some inconsistency between their data although most of their data are highly consistent. To understand the differences, the knowledge of archiving and off-line processing of spacecraft is required because these differences are caused by the off-line processing.The data processing of spacecraft often requires merge and sort processing of raw data. The merge processing is normally performed to eliminate duplicated data, and the sort processing is performed to fix data order. UTIG did not seem to perform these merge and sort processing. Therefore, the UTIG processed data remain duplication. The MIT processed data did these merge and sort processing, but the raw data sometimes include wrong time tags, and it cannot be fixed strictly after sort processing. Also, the MIT processed data has enough documents to understand metadata, while UTIG data has a brief instruction. Therefore, both of MIT and UTIG data are treated complementary. A better data set can be established using both of them. In this presentation, we would show the method to build a better data set of Viking Lander 2 seismic data.

Holistic processing, contact, and the other-race effect in face recognition.

PubMed

Zhao, Mintao; Hayward, William G; Bülthoff, Isabelle

2014-12-01

Face recognition, holistic processing, and processing of configural and featural facial information are known to be influenced by face race, with better performance for own- than other-race faces. However, whether these various other-race effects (OREs) arise from the same underlying mechanisms or from different processes remains unclear. The present study addressed this question by measuring the OREs in a set of face recognition tasks, and testing whether these OREs are correlated with each other. Participants performed different tasks probing (1) face recognition, (2) holistic processing, (3) processing of configural information, and (4) processing of featural information for both own- and other-race faces. Their contact with other-race people was also assessed with a questionnaire. The results show significant OREs in tasks testing face memory and processing of configural information, but not in tasks testing either holistic processing or processing of featural information. Importantly, there was no cross-task correlation between any of the measured OREs. Moreover, the level of other-race contact predicted only the OREs obtained in tasks testing face memory and processing of configural information. These results indicate that these various cross-race differences originate from different aspects of face processing, in contrary to the view that the ORE in face recognition is due to cross-race differences in terms of holistic processing. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Process monitoring and visualization solutions for hot-melt extrusion: a review.

PubMed

Saerens, Lien; Vervaet, Chris; Remon, Jean Paul; De Beer, Thomas

2014-02-01

Hot-melt extrusion (HME) is applied as a continuous pharmaceutical manufacturing process for the production of a variety of dosage forms and formulations. To ensure the continuity of this process, the quality of the extrudates must be assessed continuously during manufacturing. The objective of this review is to provide an overview and evaluation of the available process analytical techniques which can be applied in hot-melt extrusion. Pharmaceutical extruders are equipped with traditional (univariate) process monitoring tools, observing barrel and die temperatures, throughput, screw speed, torque, drive amperage, melt pressure and melt temperature. The relevance of several spectroscopic process analytical techniques for monitoring and control of pharmaceutical HME has been explored recently. Nevertheless, many other sensors visualizing HME and measuring diverse critical product and process parameters with potential use in pharmaceutical extrusion are available, and were thoroughly studied in polymer extrusion. The implementation of process analytical tools in HME serves two purposes: (1) improving process understanding by monitoring and visualizing the material behaviour and (2) monitoring and analysing critical product and process parameters for process control, allowing to maintain a desired process state and guaranteeing the quality of the end product. This review is the first to provide an evaluation of the process analytical tools applied for pharmaceutical HME monitoring and control, and discusses techniques that have been used in polymer extrusion having potential for monitoring and control of pharmaceutical HME. © 2013 Royal Pharmaceutical Society.

Process for improving metal production in steelmaking processes

DOEpatents

Pal, Uday B.; Gazula, Gopala K. M.; Hasham, Ali

1996-01-01

A process and apparatus for improving metal production in ironmaking and steelmaking processes is disclosed. The use of an inert metallic conductor in the slag containing crucible and the addition of a transition metal oxide to the slag are the disclosed process improvements.

Materials processing in space: Early experiments

NASA Technical Reports Server (NTRS)

Naumann, R. J.; Herring, H. W.

1980-01-01

The characteristics of the space environment were reviewed. Potential applications of space processing are discussed and include metallurgical processing, and processing of semiconductor materials. The behavior of fluid in low gravity is described. The evolution of apparatus for materials processing in space was reviewed.

Abhijit Dutta | NREL

Science.gov Websites

Techno-economic analysis Process model development for existing and conceptual processes Detailed heat integration Economic analysis of integrated processes Integration of process simulation learnings into control ;Conceptual Process Design and Techno-Economic Assessment of Ex Situ Catalytic Fast Pyrolysis of Biomass: A

7 CFR 52.806 - Color.

Code of Federal Regulations, 2012 CFR

2012-01-01

... PROCESSED FRUITS AND VEGETABLES, PROCESSED PRODUCTS THEREOF, AND CERTAIN OTHER PROCESSED FOOD PRODUCTS 1... cherries that vary markedly from this color due to oxidation, improper processing, or other causes, or that... to oxidation, improper processing, or other causes, or that are undercolored, does not exceed the...

7 CFR 52.806 - Color.

Code of Federal Regulations, 2011 CFR

2011-01-01

... PROCESSED FRUITS AND VEGETABLES, PROCESSED PRODUCTS THEREOF, AND CERTAIN OTHER PROCESSED FOOD PRODUCTS 1... cherries that vary markedly from this color due to oxidation, improper processing, or other causes, or that... to oxidation, improper processing, or other causes, or that are undercolored, does not exceed the...

Meat Processing.

ERIC Educational Resources Information Center

Legacy, Jim; And Others

This publication provides an introduction to meat processing for adult students in vocational and technical education programs. Organized in four chapters, the booklet provides a brief overview of the meat processing industry and the techniques of meat processing and butchering. The first chapter introduces the meat processing industry and…

40 CFR 60.2025 - What if my chemical recovery unit is not listed in § 60.2020(n)?

Code of Federal Regulations, 2011 CFR

2011-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

40 CFR 60.2025 - What if my chemical recovery unit is not listed in § 60.2020(n)?

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

40 CFR 60.2025 - What if my chemical recovery unit is not listed in § 60.2020(n)?

Code of Federal Regulations, 2010 CFR

2010-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

40 CFR 60.2558 - What if a chemical recovery unit is not listed in § 60.2555(n)?

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

Integrated decontamination process for metals

DOEpatents

Snyder, Thomas S.; Whitlow, Graham A.

1991-01-01

An integrated process for decontamination of metals, particularly metals that are used in the nuclear energy industry contaminated with radioactive material. The process combines the processes of electrorefining and melt refining to purify metals that can be decontaminated using either electrorefining or melt refining processes.

Case Studies in Continuous Process Improvement

NASA Technical Reports Server (NTRS)

Mehta, A.

1997-01-01

This study focuses on improving the SMT assembly process in a low-volume, high-reliability environment with emphasis on fine pitch and BGA packages. Before a process improvement is carried out, it is important to evaluate where the process stands in terms of process capability.

Mathematical Model of Nonstationary Separation Processes Proceeding in the Cascade of Gas Centrifuges in the Process of Separation of Multicomponent Isotope Mixtures

NASA Astrophysics Data System (ADS)

Orlov, A. A.; Ushakov, A. A.; Sovach, V. P.

2017-03-01

We have developed and realized on software a mathematical model of the nonstationary separation processes proceeding in the cascades of gas centrifuges in the process of separation of multicomponent isotope mixtures. With the use of this model the parameters of the separation process of germanium isotopes have been calculated. It has been shown that the model adequately describes the nonstationary processes in the cascade and is suitable for calculating their parameters in the process of separation of multicomponent isotope mixtures.

International Best Practices for Pre-Processing and Co-Processing Municipal Solid Waste and Sewage Sludge in the Cement Industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasanbeigi, Ali; Lu, Hongyou; Williams, Christopher

The purpose of this report is to describe international best practices for pre-processing and coprocessing of MSW and sewage sludge in cement plants, for the benefit of countries that wish to develop co-processing capacity. The report is divided into three main sections. Section 2 describes the fundamentals of co-processing, Section 3 describes exemplary international regulatory and institutional frameworks for co-processing, and Section 4 describes international best practices related to the technological aspects of co-processing.

Thermochemical water decomposition processes

NASA Technical Reports Server (NTRS)

Chao, R. E.

1974-01-01

Thermochemical processes which lead to the production of hydrogen and oxygen from water without the consumption of any other material have a number of advantages when compared to other processes such as water electrolysis. It is possible to operate a sequence of chemical steps with net work requirements equal to zero at temperatures well below the temperature required for water dissociation in a single step. Various types of procedures are discussed, giving attention to halide processes, reverse Deacon processes, iron oxide and carbon oxide processes, and metal and alkali metal processes. Economical questions are also considered.

Voyager image processing at the Image Processing Laboratory

NASA Astrophysics Data System (ADS)

Jepsen, P. L.; Mosher, J. A.; Yagi, G. M.; Avis, C. C.; Lorre, J. J.; Garneau, G. W.

1980-09-01

This paper discusses new digital processing techniques as applied to the Voyager Imaging Subsystem and devised to explore atmospheric dynamics, spectral variations, and the morphology of Jupiter, Saturn and their satellites. Radiometric and geometric decalibration processes, the modulation transfer function, and processes to determine and remove photometric properties of the atmosphere and surface of Jupiter and its satellites are examined. It is exhibited that selected images can be processed into 'approach at constant longitude' time lapse movies which are useful in observing atmospheric changes of Jupiter. Photographs are included to illustrate various image processing techniques.

Voyager image processing at the Image Processing Laboratory

NASA Technical Reports Server (NTRS)

Jepsen, P. L.; Mosher, J. A.; Yagi, G. M.; Avis, C. C.; Lorre, J. J.; Garneau, G. W.

1980-01-01

This paper discusses new digital processing techniques as applied to the Voyager Imaging Subsystem and devised to explore atmospheric dynamics, spectral variations, and the morphology of Jupiter, Saturn and their satellites. Radiometric and geometric decalibration processes, the modulation transfer function, and processes to determine and remove photometric properties of the atmosphere and surface of Jupiter and its satellites are examined. It is exhibited that selected images can be processed into 'approach at constant longitude' time lapse movies which are useful in observing atmospheric changes of Jupiter. Photographs are included to illustrate various image processing techniques.

A novel process control method for a TT-300 E-Beam/X-Ray system

NASA Astrophysics Data System (ADS)

Mittendorfer, Josef; Gallnböck-Wagner, Bernhard

2018-02-01

This paper presents some aspects of the process control method for a TT-300 E-Beam/X-Ray system at Mediscan, Austria. The novelty of the approach is the seamless integration of routine monitoring dosimetry with process data. This allows to calculate a parametric dose for each production unit and consequently a fine grain and holistic process performance monitoring. Process performance is documented in process control charts for the analysis of individual runs as well as historic trending of runs of specific process categories over a specified time range.

A minimally processed dietary pattern is associated with lower odds of metabolic syndrome among Lebanese adults.

PubMed

Nasreddine, Lara; Tamim, Hani; Itani, Leila; Nasrallah, Mona P; Isma'eel, Hussain; Nakhoul, Nancy F; Abou-Rizk, Joana; Naja, Farah

2018-01-01

To (i) estimate the consumption of minimally processed, processed and ultra-processed foods in a sample of Lebanese adults; (ii) explore patterns of intakes of these food groups; and (iii) investigate the association of the derived patterns with cardiometabolic risk. Cross-sectional survey. Data collection included dietary assessment using an FFQ and biochemical, anthropometric and blood pressure measurements. Food items were categorized into twenty-five groups based on the NOVA food classification. The contribution of each food group to total energy intake (TEI) was estimated. Patterns of intakes of these food groups were examined using exploratory factor analysis. Multivariate logistic regression analysis was used to evaluate the associations of derived patterns with cardiometabolic risk factors. Greater Beirut area, Lebanon. Adults ≥18 years (n 302) with no prior history of chronic diseases. Of TEI, 36·53 and 27·10 % were contributed by ultra-processed and minimally processed foods, respectively. Two dietary patterns were identified: the 'ultra-processed' and the 'minimally processed/processed'. The 'ultra-processed' consisted mainly of fast foods, snacks, meat, nuts, sweets and liquor, while the 'minimally processed/processed' consisted mostly of fruits, vegetables, legumes, breads, cheeses, sugar and fats. Participants in the highest quartile of the 'minimally processed/processed' pattern had significantly lower odds for metabolic syndrome (OR=0·18, 95 % CI 0·04, 0·77), hyperglycaemia (OR=0·25, 95 % CI 0·07, 0·98) and low HDL cholesterol (OR=0·17, 95 % CI 0·05, 0·60). The study findings may be used for the development of evidence-based interventions aimed at encouraging the consumption of minimally processed foods.

Increasing patient safety and efficiency in transfusion therapy using formal process definitions.

PubMed

Henneman, Elizabeth A; Avrunin, George S; Clarke, Lori A; Osterweil, Leon J; Andrzejewski, Chester; Merrigan, Karen; Cobleigh, Rachel; Frederick, Kimberly; Katz-Bassett, Ethan; Henneman, Philip L

2007-01-01

The administration of blood products is a common, resource-intensive, and potentially problem-prone area that may place patients at elevated risk in the clinical setting. Much of the emphasis in transfusion safety has been targeted toward quality control measures in laboratory settings where blood products are prepared for administration as well as in automation of certain laboratory processes. In contrast, the process of transfusing blood in the clinical setting (ie, at the point of care) has essentially remained unchanged over the past several decades. Many of the currently available methods for improving the quality and safety of blood transfusions in the clinical setting rely on informal process descriptions, such as flow charts and medical algorithms, to describe medical processes. These informal descriptions, although useful in presenting an overview of standard processes, can be ambiguous or incomplete. For example, they often describe only the standard process and leave out how to handle possible failures or exceptions. One alternative to these informal descriptions is to use formal process definitions, which can serve as the basis for a variety of analyses because these formal definitions offer precision in the representation of all possible ways that a process can be carried out in both standard and exceptional situations. Formal process definitions have not previously been used to describe and improve medical processes. The use of such formal definitions to prospectively identify potential error and improve the transfusion process has not previously been reported. The purpose of this article is to introduce the concept of formally defining processes and to describe how formal definitions of blood transfusion processes can be used to detect and correct transfusion process errors in ways not currently possible using existing quality improvement methods.

Chemical interaction matrix between reagents in a Purex based process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brahman, R.K.; Hennessy, W.P.; Paviet-Hartmann, P.

2008-07-01

The United States Department of Energy (DOE) is the responsible entity for the disposal of the United States excess weapons grade plutonium. DOE selected a PUREX-based process to convert plutonium to low-enriched mixed oxide fuel for use in commercial nuclear power plants. To initiate this process in the United States, a Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF) is under construction and will be operated by Shaw AREVA MOX Services at the Savannah River Site. This facility will be licensed and regulated by the U.S. Nuclear Regulatory Commission (NRC). A PUREX process, similar to the one used at La Hague,more » France, will purify plutonium feedstock through solvent extraction. MFFF employs two major process operations to manufacture MOX fuel assemblies: (1) the Aqueous Polishing (AP) process to remove gallium and other impurities from plutonium feedstock and (2) the MOX fuel fabrication process (MP), which processes the oxides into pellets and manufactures the MOX fuel assemblies. The AP process consists of three major steps, dissolution, purification, and conversion, and is the center of the primary chemical processing. A study of process hazards controls has been initiated that will provide knowledge and protection against the chemical risks associated from mixing of reagents over the life time of the process. This paper presents a comprehensive chemical interaction matrix evaluation for the reagents used in the PUREX-based process. Chemical interaction matrix supplements the process conditions by providing a checklist of any potential inadvertent chemical reactions that may take place. It also identifies the chemical compatibility/incompatibility of the reagents if mixed by failure of operations or equipment within the process itself or mixed inadvertently by a technician in the laboratories. (aut0010ho.« less

Ultra-processed foods have the worst nutrient profile, yet they are the most available packaged products in a sample of New Zealand supermarkets.

PubMed

Luiten, Claire M; Steenhuis, Ingrid Hm; Eyles, Helen; Ni Mhurchu, Cliona; Waterlander, Wilma E

2016-02-01

To examine the availability of packaged food products in New Zealand supermarkets by level of industrial processing, nutrient profiling score (NPSC), price (energy, unit and serving costs) and brand variety. Secondary analysis of cross-sectional survey data on packaged supermarket food and non-alcoholic beverages. Products were classified according to level of industrial processing (minimally, culinary and ultra-processed) and their NPSC. Packaged foods available in four major supermarkets in Auckland, New Zealand. Packaged supermarket food products for the years 2011 and 2013. The majority (84% in 2011 and 83% in 2013) of packaged foods were classified as ultra-processed. A significant positive association was found between the level of industrial processing and NPSC, i.e., ultra-processed foods had a worse nutrient profile (NPSC=11.63) than culinary processed foods (NPSC=7.95), which in turn had a worse nutrient profile than minimally processed foods (NPSC=3.27), P<0.001. No clear associations were observed between the three price measures and level of processing. The study observed many variations of virtually the same product. The ten largest food manufacturers produced 35% of all packaged foods available. In New Zealand supermarkets, ultra-processed foods comprise the largest proportion of packaged foods and are less healthy than less processed foods. The lack of significant price difference between ultra- and less processed foods suggests ultra-processed foods might provide time-poor consumers with more value for money. These findings highlight the need to improve the supermarket food supply by reducing numbers of ultra-processed foods and by reformulating products to improve their nutritional profile.

Trends in consumption of ultra-processed foods and obesity in Sweden between 1960 and 2010.

PubMed

Juul, Filippa; Hemmingsson, Erik

2015-12-01

To investigate how consumption of ultra-processed foods has changed in Sweden in relation to obesity. Nationwide ecological analysis of changes in processed foods along with corresponding changes in obesity. Trends in per capita food consumption during 1960-2010 were investigated using data from the Swedish Board of Agriculture. Food items were classified as group 1 (unprocessed/minimally processed), group 2 (processed culinary ingredients) or group 3 (3·1, processed food products; and 3·2, ultra-processed products). Obesity prevalence data were pooled from the peer-reviewed literature, Statistics Sweden and the WHO Global Health Observatory. Nationwide analysis in Sweden, 1960-2010. Swedish nationals aged 18 years and older. During the study period consumption of group 1 foods (minimal processing) decreased by 2 %, while consumption of group 2 foods (processed ingredients) decreased by 34 %. Consumption of group 3·1 foods (processed food products) increased by 116 % and group 3·2 foods (ultra-processed products) increased by 142 %. Among ultra-processed products, there were particularly large increases in soda (315 %; 22 v. 92 litres/capita per annum) and snack foods such as crisps and candies (367 %; 7 v. 34 kg/capita per annum). In parallel to these changes in ultra-processed products, rates of adult obesity increased from 5 % in 1980 to over 11 % in 2010. The consumption of ultra-processed products (i.e. foods with low nutritional value but high energy density) has increased dramatically in Sweden since 1960, which mirrors the increased prevalence of obesity. Future research should clarify the potential causal role of ultra-processed products in weight gain and obesity.

Differential Phonological and Semantic Modulation of Neurophysiological Responses to Visual Word Recognition.

PubMed

Drakesmith, Mark; El-Deredy, Wael; Welbourne, Stephen

2015-01-01

Reading words for meaning relies on orthographic, phonological and semantic processing. The triangle model implicates a direct orthography-to-semantics pathway and a phonologically mediated orthography-to-semantics pathway, which interact with each other. The temporal evolution of processing in these routes is not well understood, although theoretical evidence predicts early phonological processing followed by interactive phonological and semantic processing. This study used electroencephalography-event-related potential (ERP) analysis and magnetoencephalography (MEG) source localisation to identify temporal markers and the corresponding neural generators of these processes in early (∼200 ms) and late (∼400 ms) neurophysiological responses to visual words, pseudowords and consonant strings. ERP showed an effect of phonology but not semantics in both time windows, although at ∼400 ms there was an effect of stimulus familiarity. Phonological processing at ~200 ms was localised to the left occipitotemporal cortex and the inferior frontal gyrus. At 400 ms, there was continued phonological processing in the inferior frontal gyrus and additional semantic processing in the anterior temporal cortex. There was also an area in the left temporoparietal junction which was implicated in both phonological and semantic processing. In ERP, the semantic response at ∼400 ms appeared to be masked by concurrent processes relating to familiarity, while MEG successfully differentiated these processes. The results support the prediction of early phonological processing followed by an interaction of phonological and semantic processing during word recognition. Neuroanatomical loci of these processes are consistent with previous neuropsychological and functional magnetic resonance imaging studies. The results also have implications for the classical interpretation of N400-like responses as markers for semantic processing.

Basic abnormalities in visual processing affect face processing at an early age in autism spectrum disorder.

PubMed

Vlamings, Petra Hendrika Johanna Maria; Jonkman, Lisa Marthe; van Daalen, Emma; van der Gaag, Rutger Jan; Kemner, Chantal

2010-12-15

A detailed visual processing style has been noted in autism spectrum disorder (ASD); this contributes to problems in face processing and has been directly related to abnormal processing of spatial frequencies (SFs). Little is known about the early development of face processing in ASD and the relation with abnormal SF processing. We investigated whether young ASD children show abnormalities in low spatial frequency (LSF, global) and high spatial frequency (HSF, detailed) processing and explored whether these are crucially involved in the early development of face processing. Three- to 4-year-old children with ASD (n = 22) were compared with developmentally delayed children without ASD (n = 17). Spatial frequency processing was studied by recording visual evoked potentials from visual brain areas while children passively viewed gratings (HSF/LSF). In addition, children watched face stimuli with different expressions, filtered to include only HSF or LSF. Enhanced activity in visual brain areas was found in response to HSF versus LSF information in children with ASD, in contrast to control subjects. Furthermore, facial-expression processing was also primarily driven by detail in ASD. Enhanced visual processing of detailed (HSF) information is present early in ASD and occurs for neutral (gratings), as well as for socially relevant stimuli (facial expressions). These data indicate that there is a general abnormality in visual SF processing in early ASD and are in agreement with suggestions that a fast LSF subcortical face processing route might be affected in ASD. This could suggest that abnormal visual processing is causative in the development of social problems in ASD. Copyright © 2010 Society of Biological Psychiatry. Published by Elsevier Inc. All rights reserved.

[Contention on the theory of processing techniques of Chinese materia medica in the Ming-Qing period].

PubMed

Chen, Bin; Jia, Tianzhu

2015-03-01

On the basis of the golden stage of development of processing techniques of medicinals in the Song dynasty, the theory and techniques of processing in the Ming-Qing dynasties developed and accomplished further. The knowledge of some physicians on the processing of common medicinal, such as Radix rehmannia and Radixophiopogonis, was questioned, with new idea of processing methods put forward and argued against those insisting traditional ones, marking the progress of the art of processing. By reviewing the contention of technical theory of medicinal processing in the Ming-Qing period, useful references can be provided for the inheritance and development of the traditional art of processing medicinals.

Process Feasibility Study in Support of Silicon Material, Task 1

NASA Technical Reports Server (NTRS)

Li, K. Y.; Hansen, K. C.; Yaws, C. L.

1979-01-01

During this reporting period, major activies were devoted to process system properties, chemical engineering and economic analyses. Analyses of process system properties was continued for materials involved in the alternate processes under consideration for solar cell grade silicon. The following property data are reported for silicon tetrafluoride: critical constants, vapor pressure, heat of varporization, heat capacity, density, surface tension, viscosity, thermal conductivity, heat of formation and Gibb's free energy of formation. Chemical engineering analysis of the BCL process was continued with primary efforts being devoted to the preliminary process design. Status and progress are reported for base case conditions; process flow diagram; reaction chemistry; material and energy balances; and major process equipment design.

Technology and development requirements for advanced coal conversion systems

NASA Technical Reports Server (NTRS)

1981-01-01

A compendium of coal conversion process descriptions is presented. The SRS and MC data bases were utilized to provide information paticularly in the areas of existing process designs and process evaluations. Additional information requirements were established and arrangements were made to visit process developers, pilot plants, and process development units to obtain information that was not otherwise available. Plant designs, process descriptions and operating conditions, and performance characteristics were analyzed and requirements for further development identified and evaluated to determine the impact of these requirements on the process commercialization potential from the standpoint of economics and technical feasibility. A preliminary methodology was established for the comparative technical and economic assessment of advanced processes.