Method of automatic measurement and focus of an electron beam and apparatus therefor

DOEpatents

Giedt, Warren H.; Campiotti, Richard

1996-01-01

An electron beam focusing system, including a plural slit-type Faraday beam trap, for measuring the diameter of an electron beam and automatically focusing the beam for welding. Beam size is determined from profiles of the current measured as the beam is swept over at least two narrow slits of the beam trap. An automated procedure changes the focus coil current until the focal point location is just below a workpiece surface. A parabolic equation is fitted to the calculated beam sizes from which optimal focus coil current and optimal beam diameter are determined.

CT Scanning in Identification of Sheep Cystic Echinococcosis.

PubMed

Mao, Rui; Qi, Hongzhi; Pei, Lei; Hao, Jie; Dong, Jian; Jiang, Tao; Ainiwaer, Abudula; Shang, Ge; Xu, Lin; Shou, Xi; Zhang, Songan; Wu, Ge; Lu, Pengfei; Bao, Yongxing; Li, Haitao

2017-01-01

We aim to determine the efficiency of CT in identification of cystic echinococcosis in sheep. Fifty-three sheep with liver cysts confirmed by ultrasonography were subject to CT scan to evaluate the number, size, and type of the cysts in liver and lung, confirmed using necropsy. The correlation of numbers between liver cysts and lung cysts was calculated using Pearson analysis. Necropsy indicated a 98% consensus on size, location, number, and activity compared with CT scan. The viable cysts were 53.1% and 50.6% in the liver and lung, respectively. Among the cysts in liver, 35.5%, 9.5%, 5.7%, 10.2%, and 39.1% were Types CE1, CE2, CE3, CE4, and CE5, respectively. The cysts in the lungs, 17.4%, 26.9%, 12.1%, 11.6%, and 32.1%, were Types CE1, CE2, CE3, CE4, and CE5, respectively. A significant correlation was noticed between the number of cysts in liver and those in lung ( R = 0.770, P < 0.001). CT scan is a suitable tool in determining the size and type of cystic hydatid cysts in both liver and lung of sheep. A significant correlation was noticed between the numbers in liver and lung, indicating that lung infection was likely due to the expansion of liver cyst burden pressure.

Management of acute calcific tendinitis around the hip joint.

PubMed

Park, Sang-Min; Baek, Ji-Hoon; Ko, Young-Bong; Lee, Han-Jun; Park, Ki Jeong; Ha, Yong-Chan

2014-11-01

Although the natural history of calcific tendinitis within the rotator cuff of the shoulder is established, the natural history of calcific tendinitis around the hip joint remains unknown. To examine the duration of symptoms including pain, the location of calcific tendinitis around the hip joint, the radiologic course of calcium phosphate crystals, and the proportion of patients who required surgical treatment. Case series; Level of evidence, 4. Thirty hips (29 patients) with acute calcific tendinitis were treated between January 2010 and December 2012. Level of subjective hip pain using the visual analog scale pain score, radiologic type, and the location and size of calcium deposits were measured during a follow-up period of 12 to 32 months. The 29 patients included 7 men (24%) and 22 women (76%) with a mean age of 51.5 years (range, 28-78 years). All visual analog scale pain scores significantly improved from a mean of 7.1 to 0.8 at the latest follow-up (P < .001). The most common site of calcium deposition was the tendon of the gluteus medius. During follow-up, calcium deposition completely resolved in 5 of 20 hips. Symptoms in 23 patients (24 hips) responded to nonoperative treatment. Two patients (2 hips) were treated with ultrasound-guided local anesthetic and steroid injection. Four patients (4 hips) with long duration (>3 months) of severe pain, solid type, and large size (range, 96-416 mm(2)) were treated with arthroscopic excision. Nonoperative treatment in patients with acute calcific tendinitis of the hip joint might be successful in most patients. Surgical treatment is of value for patients experiencing prolonged severe pain, solid type, and large size. © 2014 The Author(s).

Automated nodule location and size estimation using a multi-scale Laplacian of Gaussian filtering approach.

PubMed

Jirapatnakul, Artit C; Fotin, Sergei V; Reeves, Anthony P; Biancardi, Alberto M; Yankelevitz, David F; Henschke, Claudia I

2009-01-01

Estimation of nodule location and size is an important pre-processing step in some nodule segmentation algorithms to determine the size and location of the region of interest. Ideally, such estimation methods will consistently find the same nodule location regardless of where the the seed point (provided either manually or by a nodule detection algorithm) is placed relative to the "true" center of the nodule, and the size should be a reasonable estimate of the true nodule size. We developed a method that estimates nodule location and size using multi-scale Laplacian of Gaussian (LoG) filtering. Nodule candidates near a given seed point are found by searching for blob-like regions with high filter response. The candidates are then pruned according to filter response and location, and the remaining candidates are sorted by size and the largest candidate selected. This method was compared to a previously published template-based method. The methods were evaluated on the basis of stability of the estimated nodule location to changes in the initial seed point and how well the size estimates agreed with volumes determined by a semi-automated nodule segmentation method. The LoG method exhibited better stability to changes in the seed point, with 93% of nodules having the same estimated location even when the seed point was altered, compared to only 52% of nodules for the template-based method. Both methods also showed good agreement with sizes determined by a nodule segmentation method, with an average relative size difference of 5% and -5% for the LoG and template-based methods respectively.

Lesions affecting the right hippocampal formation differentially impair short-term memory of spatial and nonspatial associations.

PubMed

Braun, Mischa; Weinrich, Christiane; Finke, Carsten; Ostendorf, Florian; Lehmann, Thomas-Nicolas; Ploner, Christoph J

2011-03-01

Converging evidence from behavioral and imaging studies suggests that within the human medial temporal lobe (MTL) the hippocampal formation may be particularly involved in recognition memory of associative information. However, it is unclear whether the hippocampal formation processes all types of associations or whether there is a specialization for processing of associations involving spatial information. Here, we investigated this issue in six patients with postsurgical lesions of the right MTL affecting the hippocampal formation and in ten healthy controls. Subjects performed a battery of delayed match-to-sample tasks with two delays (900/5,000 ms) and three set sizes. Subjects were requested to remember either single features (colors, locations, shapes, letters) or feature associations (color-location, color-shape, color-letter). In the single-feature conditions, performance of patients did not differ from controls. In the association conditions, a significant delay-dependent deficit in memory of color-location associations was found. This deficit was largely independent of set size. By contrast, performance in the color-shape and color-letter conditions was normal. These findings support the hypothesis that a region within the right MTL, presumably the hippocampal formation, does not equally support all kinds of visual memory but rather has a bias for processing of associations involving spatial information. Recruitment of this region during memory tasks appears to depend both on processing type (associative/nonassociative) and to-be-remembered material (spatial/nonspatial). Copyright © 2010 Wiley-Liss, Inc.

Movements of northern flying squirrels in different-aged forest stands of western Oregon

USGS Publications Warehouse

Martin, K.J.; Anthony, R.G.

1999-01-01

In western Oregon, northern flying squirrels (Glaucomys sabrinus) are the primary prey species for northern spotted owls (Strix occidentalis caurina), an old-growth associated species. To assess differences between old-growth and second-growth habitat, we livetrapped and radiotagged 39 northern flying squirrels to estimate their home range sizes and describe movements in 2 old-growth and 2 second-growth conifer forest stands in the Cascade Mountains of central Oregon. Sampling periods were summer and fall of 1991-92. Home range sizes averaged 4.9 ha and did not differ (P > 0.30) between the 2 stand types. Male northern flying squirrels had larger (P ??? 0.03) mean home ranges (5.9 ?? 0.8 ha; ?? ?? SE; n = 20) than females (3.9 ?? 0.4 ha; n = 19). Northern flying squirrel movement distances between successive, noncorrelated telemetry locations averaged 71 m (n = 1,090). No correlation was found between distances moved and stand type or sex. Northern flying squirrel's home range sizes, movements, and densities were similar between the 2 stand types. We suggest abundance and movements of northern flying squirrels are not influencing the preferential selection of oldgrowth forests by northern spotted owls.

Testing releasable GPS radiocollars on wolves and white-tailed deer

USGS Publications Warehouse

Merrill, Samuel B.; Adams, Layne G.; Nelson, Michael E.; Mech, L. David

1999-01-01

We tested prototype GPS collars on 8 free-ranging wolves (Canis lupus) and 3 white-tailed deer (Odocoileus virginianus) for varying periods between February and August 1997. We programmed the 920-gm collars to make a location attempt 6-96 times per day. The collars were designed to be remotely released from the animal and the data were then downloaded to a desktop computer. The collars produced 47-1,549 locations each during 11-41 days; locations were successful in 26-95% of the attempts (x̄ = 70%). Eight collars released successfully. Three collar-release failures were caused by condensation. Two collars had GPS antennas that were improperly attached and did not collect data. Life was as long as, or longer than, expected in 4 collars, less than expected in 5 collars, and unknown in 2 collars. Limitations of this type of collar include brief life if programmed at short location-attempt intervals (≤1 hr) and possible drop-off failure. Nevertheless, the large volume of data we collected with no field telemetry effort demonstrates the potential for this type of GPS collar to answer questions about movements of medium-sized mammals.

Comparison of Optic Disc Margin Identified by Color Disc Photography and High-Speed Ultrahigh-Resolution Optical Coherence Tomography

PubMed Central

Manassakorn, Anita; Ishikawa, Hiroshi; Kim, Jong S.; Wollstein, Gadi; Bilonick, Richard A.; Kagemann, Larry; Gabriele, Michelle L.; Sung, Kyung Rim; Mumcuoglu, Tarkan; Duker, Jay S.; Fujimoto, James G.; Schuman, Joel S.

2009-01-01

Objective To determine the correspondence between optic disc margins evaluated using disc photography (DP) and optical coherence tomography (OCT). Methods From May 1, 2005, through November 10, 2005, 17 healthy volunteers (17 eyes) had raster scans (180 frames, 501 samplings per frame) centered on the optic disc taken with stereo-optic DP and high-speed ultrahigh-resolution OCT (hsUHR-OCT). Two image outputs were derived from the hsUHR-OCT data set: an en face hsUHR-OCT fundus image and a set of 180 frames of cross-sectional images. Three ophthalmologists independently and in a masked, randomized fashion marked the disc margin on the DP, hsUHR-OCT fundus, and cross-sectional images using custom software. Disc size (area and horizontal and vertical diameters) and location of the geometric disc center were compared among the 3 types of images. Results The hsUHR-OCT fundus image definition showed a significantly smaller disc size than the DP definition (P<.001, mixed-effects analysis). The hsUHR-OCT cross-sectional image definition showed a significantly larger disc size than the DP definition (P<.001). The geometric disc center location was similar among the 3 types of images except for the y-coordinate, which was significantly smaller in the hsUHR-OCT fundus images than in the DP images. Conclusion The optic disc margin as defined by hsUHR-OCT was significantly different than the margin defined by DP. PMID:18195219

A comprehensive defect data bank for no. 2 common oak lumber

Treesearch

Edwin L. Lucas; Leathern R.R. Catron; Leathern R.R. Catron

1973-01-01

Computer simulation of rough mill cut-up operations allows lowcost evaluation of furniture rough mill cut-up procedures. The defect data bank serves as input to such simulation programs. The data bank contains a detailed accounting of defect data taken from 637 No. 2 Common oak boards. Included is a description of each defect (location, size, and type), as well as the...

Recommendations for the use of mist nets for inventory and monitoring of bird populations

Treesearch

C. John Ralph; Erica H. Dunn; Will J. Peach; Colleen M. Handel

2004-01-01

We provide recommendations on the best practices for mist netting for the purposes of monitoring population parameters such as abundance and demography. Studies should be carefully thought out before nets are set up, to ensure that sampling design and estimated sample size will allow study objectives to be met. Station location, number of nets, type of nets, net...

Theoretical study of nitrogen-doped graphene nanoflakes: Stability and spectroscopy depending on dopant types and flake sizes.

PubMed

Lin, Chih-Kai

2018-03-05

As nitrogen-doped graphene has been widely applied in optoelectronic devices and catalytic reactions, in this work we have investigated where the nitrogen atoms tend to reside in the material and how they affect the electron density and spectroscopic properties from a theoretical point of view. DFT calculations on N-doped hexagonal and rectangular graphene nanoflakes (GNFs) showed that nitrogen atoms locating on zigzag edges are obviously more stable than those on armchair edges or inside flakes, and interestingly, the N-hydrogenated pyridine moiety could be preferable to pure pyridine moiety in large models. The UV-vis absorption spectra of these nitrogen-doped GNFs display strong dependence on flake sizes, where the larger flakes have their major peaks in lower energy ranges. Moreover, the spectra exhibit different connections to various dopant types and positions: the graphitic-type dopant species present large variety in absorption profiles, while the pyridinic-type ones show extraordinary uniform stability and spectra independent of dopant positions/numbers and hence are hardly distinguishable from each other. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

The elevation and its distribution in geomorphological regions of the European Russia

NASA Astrophysics Data System (ADS)

Kharchenko, S. V.; Ermolaev, O. P.; Mukharamova, S. S.

2018-01-01

Spatial differences of elevation were analysed by side of view of geomorphological boundaries on the European Russia territory. Geomorphological pattern of the studied territory was taken from Geomorphological Map of the USSR at scale of 1: 2 500 000. There 2401 fragments for combinations of 58 types of structural landforms and 22 types of sculptural landforms were allocated. The elevation values computed by digital elevation model (cell size - 200 m, number of cells - 322M) based on SRTM (south of 60 nl.) and GDEM 2010 (north of 60 nl.) resampled data. It was founded that some types of structural (16 types) and sculptural (6 types) landforms located in the relatively thin intervals of elevation. Using of elevation above sea level is needed for effective automatic recognizing these landform regions.

Field-aligned currents associated with multiple arc systems

NASA Astrophysics Data System (ADS)

Wu, J.; Knudsen, D. J.; Gillies, D. M.; Donovan, E.; Burchill, J. K.

2016-12-01

It is often thought that auroral arcs are a direct consequence of upward field-aligned currents. In fact, the relation between currents and brightness is more complicated. Multiple auroral arc systems provide and opportunity to study this relation in detail; this information can be used as a test of models for quasi-static arc formation. In this study, we have identified two types of FAC configurations in multiple parallel arc systems using ground-based optical data from the THEMIS all-sky imagers (ASIs), magnetometers and electric field instruments onboard the Swarm satellites during the period from December 2013 to March 2015. In type 1 events, each arc is an intensification within a broad, unipolar current sheet and downward currents only exist outside the upward current sheet. In type 2 events, multiple arc systems represent a collection of multiple up/down current pairs. By collecting 12 events for type 1 and 17 events for type 2, we find that (1) Type 1 events are mainly located between 22-23MLT. Type 2 events are mainly located around midnight. (2) The typical size of upward and downward FAC in type 2 events are comparable, while upward FAC in type 1 events are larger than downward FAC. (3) Upward currents with more arcs embedded have larger intensities and widths. (4) There is no significant difference between the characteristic widths of multiple arcs and single arcs.

Invariant TAD Boundaries Constrain Cell-Type-Specific Looping Interactions between Promoters and Distal Elements around the CFTR Locus.

PubMed

Smith, Emily M; Lajoie, Bryan R; Jain, Gaurav; Dekker, Job

2016-01-07

Three-dimensional genome structure plays an important role in gene regulation. Globally, chromosomes are organized into active and inactive compartments while, at the gene level, looping interactions connect promoters to regulatory elements. Topologically associating domains (TADs), typically several hundred kilobases in size, form an intermediate level of organization. Major questions include how TADs are formed and how they are related to looping interactions between genes and regulatory elements. Here we performed a focused 5C analysis of a 2.8 Mb chromosome 7 region surrounding CFTR in a panel of cell types. We find that the same TAD boundaries are present in all cell types, indicating that TADs represent a universal chromosome architecture. Furthermore, we find that these TAD boundaries are present irrespective of the expression and looping of genes located between them. In contrast, looping interactions between promoters and regulatory elements are cell-type specific and occur mostly within TADs. This is exemplified by the CFTR promoter that in different cell types interacts with distinct sets of distal cell-type-specific regulatory elements that are all located within the same TAD. Finally, we find that long-range associations between loci located in different TADs are also detected, but these display much lower interaction frequencies than looping interactions within TADs. Interestingly, interactions between TADs are also highly cell-type-specific and often involve loci clustered around TAD boundaries. These data point to key roles of invariant TAD boundaries in constraining as well as mediating cell-type-specific long-range interactions and gene regulation. Copyright © 2016 The American Society of Human Genetics. Published by Elsevier Inc. All rights reserved.

Afferent innervation patterns of the saccule in pigeons

NASA Technical Reports Server (NTRS)

Zakir, M.; Huss, D.; Dickman, J. D.

2003-01-01

The innervation patterns of vestibular saccular afferents were quantitatively investigated in pigeons using biotinylated dextran amine as a neural tracer and three-dimensional computer reconstruction. Type I hair cells were found throughout a large portion of the macula, with the highest density observed in the striola. Type II hair cells were located throughout the macula, with the highest density in the extrastriola. Three classes of afferent innervation patterns were observed, including calyx, dimorph, and bouton units, with 137 afferents being anatomically reconstructed and used for quantitative comparisons. Calyx afferents were located primarily in the striola, innervated a number of type I hair cells, and had small innervation areas. Most calyx afferent terminal fields were oriented parallel to the anterior-posterior axis and the morphological polarization reversal line. Dimorph afferents were located throughout the macula, contained fewer type I hair cells in a calyceal terminal than calyx afferents and had medium sized innervation areas. Bouton afferents were restricted to the extrastriola, with multi-branching fibers and large innervation areas. Most of the dimorph and bouton afferents had innervation fields that were oriented dorso-ventrally but were parallel to the neighboring reversal line. The organizational morphology of the saccule was found to be distinctly different from that of the avian utricle or lagena otolith organs and appears to represent a receptor organ undergoing evolutionary adaptation toward sensing linear motion in terrestrial and aerial species.

Martian deltas: Morphology and distribution

NASA Technical Reports Server (NTRS)

Rice, J. W., Jr.; Scott, D. H.

1993-01-01

Recent detailed mapping has revealed numerous examples of Martian deltas. The location and morphology of these deltas are described. Factors that contribute to delta morphology are river regime, coastal processes, structural stability, and climate. The largest delta systems on Mars are located near the mouths of Maja, Maumee, Vedra, Ma'adim, Kasei, and Brazos Valles. There are also several smaller-scale deltas emplaced near channel mouths situated in Ismenius Lacus, Memnonia, and Arabia. Delta morphology was used to reconstruct type, quantity, and sediment load size transported by the debouching channel systems. Methods initially developed for terrestrial systems were used to gain information on the relationships between Martian delta morphology, river regime, and coastal processes.

Rehabilitation strategies for partially edentulous-prosthodontic principles and current trends.

PubMed

D'Souza, Dsj; Dua, Parag

2011-07-01

The prosthetic considerations for treatment of partially edentulous patients involve evaluation of important aspects such as presence of certain functional or skeletal deficits, orientation of the occlusal plane, free-way space, size and location of edentulous areas, number, strategic location and quality of the likely abutment teeth, vertical dimension, and the type of occlusion. A comprehensive evaluation, multidisciplinary approach and a sequential treatment plan, worked out in harmony with the patient's perceptions are important factors to ensure a successful outcome. This article discusses the principles, current trends and importance of clinical decisions in designing a treatment strategy when confronted with complex situations of partial edentulism.

Sampling strategies for radio-tracking coyotes

USGS Publications Warehouse

Smith, G.J.; Cary, J.R.; Rongstad, O.J.

1981-01-01

Ten coyotes radio-tracked for 24 h periods were most active at night and moved little during daylight hours. Home-range size determined from radio-locations of 3 adult coyotes increased with the number of locations until an asymptote was reached at about 35-40 independent day locations or 3 6 nights of hourly radio-locations. Activity of the coyote did not affect the asymptotic nature of the home-range calculations, but home-range sizes determined from more than 3 nights of hourly locations were considerably larger than home-range sizes determined from daylight locations. Coyote home-range sizes were calculated from daylight locations, full-night tracking periods, and half-night tracking periods. Full- and half-lnight sampling strategies involved obtaining hourly radio-locations during 12 and 6 h periods, respectively. The half-night sampling strategy was the best compromise for our needs, as it adequately indexed the home-range size, reduced time and energy spent, and standardized the area calculation without requiring the researcher to become completely nocturnal. Sight tracking also provided information about coyote activity and sociability.

21 CFR 211.63 - Equipment design, size, and location.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 4 2014-04-01 2014-04-01 false Equipment design, size, and location. 211.63 Section 211.63 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES....63 Equipment design, size, and location. Equipment used in the manufacture, processing, packing, or...

21 CFR 211.63 - Equipment design, size, and location.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 4 2013-04-01 2013-04-01 false Equipment design, size, and location. 211.63 Section 211.63 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES....63 Equipment design, size, and location. Equipment used in the manufacture, processing, packing, or...

21 CFR 211.63 - Equipment design, size, and location.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Equipment design, size, and location. 211.63 Section 211.63 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES....63 Equipment design, size, and location. Equipment used in the manufacture, processing, packing, or...

21 CFR 211.63 - Equipment design, size, and location.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 4 2011-04-01 2011-04-01 false Equipment design, size, and location. 211.63 Section 211.63 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES....63 Equipment design, size, and location. Equipment used in the manufacture, processing, packing, or...

21 CFR 211.63 - Equipment design, size, and location.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 4 2012-04-01 2012-04-01 false Equipment design, size, and location. 211.63 Section 211.63 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES....63 Equipment design, size, and location. Equipment used in the manufacture, processing, packing, or...

A see-through holographic head-mounted display with the large viewing angle

NASA Astrophysics Data System (ADS)

Chen, Zhidong; sang, Xinzhu; Lin, Qiaojun; Li, Jin; Yu, Xunbo; Gao, Xin; Yan, Binbin; Wang, Kuiru; Yu, Chongxiu; Xie, Songlin

2017-02-01

A novel solution for the large view angle holographic head-mounted display (HHMD) is presented. Divergent light is used for the hologram illumination to construct a large size three-dimensional object outside the display in a short distance. A designed project-type lens with large numerical aperture projects the object constructed by the hologram to its real location. The presented solution can realize a compact HHMD system with a large field of view. The basic principle and the structure of the system are described. An augmented reality (AR) prototype with the size of 50 mm×40 mm and the view angle above 60° is demonstrated.

Elemental composition and size distribution of particulates in Cleveland, Ohio

NASA Technical Reports Server (NTRS)

King, R. B.; Fordyce, J. S.; Neustadter, H. E.; Leibecki, H. F.

1975-01-01

Measurements were made of the elemental particle size distribution at five contrasting urban environments with different source-type distributions in Cleveland, Ohio. Air quality conditions ranged from normal to air pollution alert levels. A parallel network of high-volume cascade impactors (5-state) were used for simultaneous sampling on glass fiber surfaces for mass determinations and on Whatman-41 surfaces for elemental analysis by neutron activation for 25 elements. The elemental data are assessed in terms of distribution functions and interrelationships and are compared between locations as a function of resultant wind direction in an attempt to relate the findings to sources.

Elemental composition and size distribution of particulates in Cleveland, Ohio

NASA Technical Reports Server (NTRS)

Leibecki, H. F.; King, R. B.; Fordyce, J. S.; Neustadter, H. E.

1975-01-01

Measurements have been made of the elemental particle size distribution at five contrasting urban environments with different source-type distributions in Cleveland, Ohio. Air quality conditions ranged from normal to air pollution alert levels. A parallel network of high-volume cascade impactors (5-stage) were used for simultaneous sampling on glass fiber surfaces for mass determinations and on Whatman-41 surfaces for elemental analysis by neutron activation for 25 elements. The elemental data are assessed in terms of distribution functions and interrelationships and are compared between locations as a function of resultant wind direction in an attempt to relate the findings to sources.

The Influence of Physical and Social Contexts of Eating on Lunch-Time Food Intake among Southern Ontario, Canada, Middle School Students

ERIC Educational Resources Information Center

Woodruff, Sarah J.; Hanning, Rhona M.; McGoldrick, Kathryn

2010-01-01

Background: Among students, little is known about the physical and social context of eating lunch. The objective of this study was to determine if food intake (including the type of food and beverages and portion sizes) was associated with specific aspects of the physical and social lunch environment (location, with whom lunch was consumed, who…

The Effect of File Size and Type and Irrigation Solutions on the Accuracy of Electronic Apex Locators: An In Vitro Study on Canine Teeth.

PubMed

Janeczek, Maciej; Kosior, Piotr; Piesiak-Pańczyszyn, Dagmara; Dudek, Krzysztof; Chrószcz, Aleksander; Czajczyńska-Waszkiewicz, Agnieszka; Kowalczyk-Zając, Małgorzata; Gabren-Syller, Aleksandra; Kirstein, Karol; Skalec, Aleksandra; Bryła, Ewelina; Dobrzyński, Maciej

2016-01-01

Measurements of the root canal during endodontic treatment have a significant influence on the course of the therapeutic process as well as on its final result in both human and veterinary medicine. The apical constriction should be the termination point for the preparation and filling of the root canal. This research was conducted with the use of a Septodont kit consisting of a small chamber filled with the examined solution in which a healthy second incisor was placed. The step back method was applied for the root canal preparation and master apical file of 30 was used. The working length was 22 mm. The examination was conducted with the use of steel as well as nickel titanium hand instruments. Different irrigation solutions and two types of apex locators were used. Measurements of the working length of the root canal showed dependence on the size of the instrument. Examinations carried out in various environments showed that analogical measurements were obtained only for sodium hypochlorite solutions. In other environments the measured sections were shortened. Comparative examinations with the use of steel instruments demonstrated insignificant measurement differences. Compared to these results, the measurements in nickel titanium group were characterized by more considerable deviations.

The Effect of File Size and Type and Irrigation Solutions on the Accuracy of Electronic Apex Locators: An In Vitro Study on Canine Teeth

PubMed Central

Kosior, Piotr; Piesiak-Pańczyszyn, Dagmara; Dudek, Krzysztof; Chrószcz, Aleksander; Czajczyńska-Waszkiewicz, Agnieszka; Kowalczyk-Zając, Małgorzata; Gabren-Syller, Aleksandra; Bryła, Ewelina

2016-01-01

Measurements of the root canal during endodontic treatment have a significant influence on the course of the therapeutic process as well as on its final result in both human and veterinary medicine. The apical constriction should be the termination point for the preparation and filling of the root canal. This research was conducted with the use of a Septodont kit consisting of a small chamber filled with the examined solution in which a healthy second incisor was placed. The step back method was applied for the root canal preparation and master apical file of 30 was used. The working length was 22 mm. The examination was conducted with the use of steel as well as nickel titanium hand instruments. Different irrigation solutions and two types of apex locators were used. Measurements of the working length of the root canal showed dependence on the size of the instrument. Examinations carried out in various environments showed that analogical measurements were obtained only for sodium hypochlorite solutions. In other environments the measured sections were shortened. Comparative examinations with the use of steel instruments demonstrated insignificant measurement differences. Compared to these results, the measurements in nickel titanium group were characterized by more considerable deviations. PMID:27747242

Target identification using Zernike moments and neural networks

NASA Astrophysics Data System (ADS)

Azimi-Sadjadi, Mahmood R.; Jamshidi, Arta A.; Nevis, Andrew J.

2001-10-01

The development of an underwater target identification algorithm capable of identifying various types of underwater targets, such as mines, under different environmental conditions pose many technical problems. Some of the contributing factors are: targets have diverse sizes, shapes and reflectivity properties. Target emplacement environment is variable; targets may be proud or partially buried. Environmental properties vary significantly from one location to another. Bottom features such as sand, rocks, corals, and vegetation can conceal a target whether it is partially buried or proud. Competing clutter with responses that closely resemble those of the targets may lead to false positives. All the problems mentioned above contribute to overly difficult and challenging conditions that could lead to unreliable algorithm performance with existing methods. In this paper, we developed and tested a shape-dependent feature extraction scheme that provides features invariant to rotation, size scaling and translation; properties that are extremely useful for any target classification problem. The developed schemes were tested on an electro-optical imagery data set collected under different environmental conditions with variable background, range and target types. The electro-optic data set was collected using a Laser Line Scan (LLS) sensor by the Coastal Systems Station (CSS), located in Panama City, Florida. The performance of the developed scheme and its robustness to distortion, rotation, scaling and translation was also studied.

The genetics of rhizosheath size in a multiparent mapping population of wheat.

PubMed

Delhaize, Emmanuel; Rathjen, Tina M; Cavanagh, Colin R

2015-08-01

Rhizosheaths comprise soil that adheres to plant roots and, in some species, are indicative of root hair length. In this study, the genetics of rhizosheath size in wheat was investigated by screening the progeny of multiparent advanced generation intercrosses (MAGIC). Two MAGIC populations were screened for rhizosheath size using a high throughput method. One MAGIC population was developed from intercrosses between four parents (4-way) and the other from intercrosses between eight parents (8-way). Transgressive segregation for rhizosheath size was observed in both the 4-way and 8-way MAGIC populations. A quantitative trait loci (QTL) analysis of the 4-way population identified six major loci located on chromosomes 2B, 4D, 5A, 5B, 6A, and 7A together accounting for 42% of the variation in rhizosheath size. Rhizosheath size was strongly correlated with root hair length and was robust across different soil types in the absence of chemical constraints. Rhizosheath size in the MAGIC populations was a reliable surrogate for root hair length and, therefore, the QTL identified probably control root hair elongation. Members of the basic helix-loop-helix family of transcription factors have previously been identified to regulate root hair length in Arabidopsis and rice. Since several wheat members of the basic helix-loop-helix family of genes are located within or near the QTL, these genes are candidates for controlling the long root hair trait. The QTL for rhizosheath size identified in this study provides the opportunity to implement marker-assisted selection to increase root hair length for improved phosphate acquisition in wheat. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

CT Scanning in Identification of Sheep Cystic Echinococcosis

PubMed Central

Mao, Rui; Qi, Hongzhi; Pei, Lei; Hao, Jie; Dong, Jian; Jiang, Tao; Ainiwaer, Abudula; Shang, Ge; Xu, Lin; Shou, Xi; Zhang, Songan; Wu, Ge; Lu, Pengfei

2017-01-01

Objective We aim to determine the efficiency of CT in identification of cystic echinococcosis in sheep. Methods Fifty-three sheep with liver cysts confirmed by ultrasonography were subject to CT scan to evaluate the number, size, and type of the cysts in liver and lung, confirmed using necropsy. The correlation of numbers between liver cysts and lung cysts was calculated using Pearson analysis. Results Necropsy indicated a 98% consensus on size, location, number, and activity compared with CT scan. The viable cysts were 53.1% and 50.6% in the liver and lung, respectively. Among the cysts in liver, 35.5%, 9.5%, 5.7%, 10.2%, and 39.1% were Types CE1, CE2, CE3, CE4, and CE5, respectively. The cysts in the lungs, 17.4%, 26.9%, 12.1%, 11.6%, and 32.1%, were Types CE1, CE2, CE3, CE4, and CE5, respectively. A significant correlation was noticed between the number of cysts in liver and those in lung (R = 0.770, P < 0.001). Conclusions CT scan is a suitable tool in determining the size and type of cystic hydatid cysts in both liver and lung of sheep. A significant correlation was noticed between the numbers in liver and lung, indicating that lung infection was likely due to the expansion of liver cyst burden pressure. PMID:29082246

Bidirectional particle transport and size selective sorting of Brownian particles in a flashing spatially periodic energy landscape.

PubMed

Martinez-Pedrero, Fernando; Massana-Cid, Helena; Ziegler, Till; Johansen, Tom H; Straube, Arthur V; Tierno, Pietro

2016-09-29

We demonstrate a size sensitive experimental scheme which enables bidirectional transport and fractionation of paramagnetic colloids in a fluid medium. It is shown that two types of magnetic colloidal particles with different sizes can be simultaneously transported in opposite directions, when deposited above a stripe-patterned ferrite garnet film subjected to a square-wave magnetic modulation. Due to their different sizes, the particles are located at distinct elevations above the surface, and they experience two different energy landscapes, generated by the modulated magnetic substrate. By combining theoretical arguments and numerical simulations, we reveal such energy landscapes, which fully explain the bidirectional transport mechanism. The proposed technique does not require pre-imposed channel geometries such as in conventional microfluidics or lab-on-a-chip systems, and permits remote control over the particle motion, speed and trajectory, by using relatively low intense magnetic fields.

Thermal Protection Materials: Development, Characterization and Evaluation

NASA Technical Reports Server (NTRS)

Johnson, Silvia M.

2012-01-01

Thermal protection materials and systems (TPS) are used to protect space vehicles from the heat experienced during entry into an atmosphere. The application for these materials is very specialized as are the materials. They must have specific properties to withstand conditions during specific entries. There is no one-size-fits-all TPS as the conditions experienced by a material are very dependent upon the atmosphere, the entry speed, the size and shape of the vehicle, and the location on the vehicle. However, all TPS must be reliable and efficient to ensure mission safety, that is to protect the vehicle while ensuring that payload is maximized. Types of TPS will be reviewed in relation to types of missions and applications. Both reusable and ablative materials will be discussed. Approaches to characterizing and evaluating these materials will be presented. The role of heritage versus new materials will be described.

Perception while watching movies: Effects of physical screen size and scene type.

PubMed

Troscianko, Tom; Meese, Timothy S; Hinde, Stephen

2012-01-01

Over the last decade, television screens and display monitors have increased in size considerably, but has this improved our televisual experience? Our working hypothesis was that the audiences adopt a general strategy that "bigger is better." However, as our visual perceptions do not tap directly into basic retinal image properties such as retinal image size (C. A. Burbeck, 1987), we wondered whether object size itself might be an important factor. To test this, we needed a task that would tap into the subjective experiences of participants watching a movie on different-sized displays with the same retinal subtense. Our participants used a line bisection task to self-report their level of "presence" (i.e., their involvement with the movie) at several target locations that were probed in a 45-min section of the movie "The Good, The Bad, and The Ugly." Measures of pupil dilation and reaction time to the probes were also obtained. In Experiment 1, we found that subjective ratings of presence increased with physical screen size, supporting our hypothesis. Face scenes also produced higher presence scores than landscape scenes for both screen sizes. In Experiment 2, reaction time and pupil dilation results showed the same trends as the presence ratings and pupil dilation correlated with presence ratings, providing some validation of the method. Overall, the results suggest that real-time measures of subjective presence might be a valuable tool for measuring audience experience for different types of (i) display and (ii) audiovisual material.

How do tablet properties influence swallowing behaviours?

PubMed

Yamamoto, Shinya; Taniguchi, Hiroshige; Hayashi, Hirokazu; Hori, Kazuhiro; Tsujimura, Takanori; Nakamura, Yuki; Sato, Hideaki; Inoue, Makoto

2014-01-01

Behavioural performance of tablet swallowing was evaluated with different tablet conditions in terms of size, number and surface coating. Four different types of tablets were prepared: small or large, and with or without a surface coating. Fourteen normal male adults were instructed to swallow the prepared tablets with 15 ml of water. The number of tablets in one trial was changed from one to three. To evaluate swallowing and tablet transport, electromyographic activity was recorded in the left suprahyoid muscles, and videofluorographic images were examined. All tablet conditions (size, number and surface coating) affected the swallowing performance in terms of total number of swallows, electromyographic burst patterns and location of remaining tablets. Increases in the size and number of tablets increased the number of swallows and electromyographic burst area and duration. In addition, all of these parameters increased while swallowing tablets without a coating compared with tablets with a coating. Location of the remaining tablets was mainly within the mouth. This study only clarified the normal pattern of tablet swallowing under several conditions in healthy subjects, but the results may facilitate comprehensive evaluation and treatment planning in terms of administering medication to dysphagic patients. © 2013 Royal Pharmaceutical Society.

Motor unit size estimation: confrontation of surface EMG with macro EMG.

PubMed

Roeleveld, K; Stegeman, D F; Falck, B; Stålberg, E V

1997-06-01

Surface EMG (SEMG) is little used for diagnostic purposes in clinical neurophysiology, mainly because it provides little direct information on individual motor units (MUs). One of the techniques to estimate the MU size is intra-muscular Macro EMG. The present study compares SEMG with Macro EMG. Fifty-eight channel SEMG was recorded simultaneously with Macro EMG. Individual MUPs were obtained by single fiber triggered averaging. All recordings were made from the biceps brachii of healthy subjects during voluntary contraction at low force. High positive correlations were found between all Macro and Surface motor unit potential (MUP) parameters: area, peak-to-peak amplitude, negative peak amplitude and positive peak amplitude. The MUPs recorded with SEMG were dependent on the distance between the MU and the skin surface. Normalizing the SEMG parameters for MU location did not improve the correlation coefficient between the parameters of both techniques. The two measurement techniques had almost the same relative range in MUP parameters in any individual subject compared to the others, especially after normalizing the surface MUP parameters for MU location. MUPs recorded with this type of SEMG provide useful information about the MU size.

Factors associated with profitability in pasture-based systems of milk production.

PubMed

Hanrahan, L; McHugh, N; Hennessy, T; Moran, B; Kearney, R; Wallace, M; Shalloo, L

2018-06-01

The global dairy industry needs to reappraise the systems of milk production that are operated at farm level with specific focus on enhancing technical efficiency and competitiveness of the sector. The objective of this study was to quantify the factors associated with costs of production, profitability, and pasture use, and the effects of pasture use on financial performance of dairy farms using an internationally recognized representative database over an 8-yr period (2008 to 2015) on pasture-based systems. To examine the associated effects of several farm system and management variables on specific performance measures, a series of multiple regression models were developed. Factors evaluated included pasture use [kg of dry matter/ha and stocking rate (livestock units/ha)], grazing season length, breeding season length, milk recording, herd size, dairy farm size (ha), farmer age, discussion group membership, proportion of purchased feed, protein %, fat %, kg of milk fat and protein per cow, kg of milk fat and protein per hectare, and capital investment in machinery, livestock, and buildings. Multiple regression analysis demonstrated costs of production per hectare differed by year, geographical location, soil type, level of pasture use, proportion of purchased feed, protein %, kg of fat and protein per cow, dairy farm size, breeding season length, and capital investment in machinery, livestock, and buildings per cow. The results of the analysis revealed that farm net profit per hectare was associated with pasture use per hectare, year, location, soil type, grazing season length, proportion of purchased feed, protein %, kg of fat and protein per cow, dairy farm size, and capital investment in machinery and buildings per cow. Pasture use per hectare was associated with year, location, soil type, stocking rate, dairy farm size, fat %, protein %, kg of fat and protein per cow, farmer age, capital investment in machinery and buildings per cow, breeding season length, and discussion group membership. On average, over the 8-yr period, each additional tonne of pasture dry matter used increased gross profit by €278 and net profit by €173 on dairy farms. Conversely, a 10% increase in the proportion of purchased feed in the diet resulted in a reduction in net profit per hectare by €97 and net profit by €207 per tonne of fat and protein. Results from this study, albeit in a quota limited environment, have demonstrated that the profitability of pasture-based dairy systems is significantly associated with the proportion of pasture used at the farm level, being cognizant of the levels of purchased feed. The Authors. Published by FASS Inc. and Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/3.0/).

Awake craniotomy for brain lesions within and near the primary motor area: A retrospective analysis of factors associated with worsened paresis in 102 consecutive patients

PubMed Central

Shinoura, Nobusada; Midorikawa, Akira; Yamada, Ryoji; Hana, Taijun; Saito, Akira; Hiromitsu, Kentaro; Itoi, Chisato; Saito, Syoko; Yagi, Kazuo

2013-01-01

Background: We analyzed factors associated with worsened paresis in a large series of patients with brain lesions located within or near the primary motor area (M1) to establish protocols for safe, awake craniotomy of eloquent lesions. Methods: We studied patients with brain lesions involving M1, the premotor area (PMA) and the primary sensory area (S1), who underwent awake craniotomy (n = 102). In addition to evaluating paresis before, during, and one month after surgery, the following parameters were analyzed: Intraoperative complications; success or failure of awake surgery; tumor type (A or B), tumor location, tumor histology, tumor size, and completeness of resection. Results: Worsened paresis at one month of follow-up was significantly associated with failure of awake surgery, intraoperative complications and worsened paresis immediately after surgery, which in turn was significantly associated with intraoperative worsening of paresis. Intraoperative worsening of paresis was significantly related to preoperative paresis, type A tumor (motor tract running in close proximity to and compressed by the tumor), tumor location within or including M1 and partial removal (PR) of the tumor. Conclusions: Successful awake surgery and prevention of deterioration of paresis immediately after surgery without intraoperative complications may help prevent worsening of paresis at one month. Factors associated with intraoperative worsening of paresis were preoperative motor deficit, type A and tumor location in M1, possibly leading to PR of the tumor. PMID:24381792

Aerosol Number Size Distribution and Type Classification from 4-Year Polarization Optical Particle Counter (POPC) Measurements at Urban-Mountain Site in Seoul

NASA Astrophysics Data System (ADS)

Park, H. J.; Kim, S. W.; Kobayashi, H.; Nishizawa, T.

2017-12-01

The Polarization Optical Particle Counter (POPC), unlike general OPCs, has the advantage capable of classifying the aerosol types (e.g., dust, anthropogenic pollution), because it measures particle number, size and depolarization ratio (DPR; the sphericity information of single particle) for 4 size bins with diameter (0.5-1, 1-3, 3-5, 5-10 μm). In this study, we investigate the temporal variations of particle number and volume size distributions with DPR values and classify aerosol types such as dust, anthropogenic pollution, from 4-year (2013-2016) POPC data at Seoul National University campus in Seoul, Korea. Coarse mode particles from 5-10 μm with relatively high DPR values (0.25-0.3) were distinctly appeared in in both spring (March-May) and winter (December-February) due to frequent transport of Asian dust particles. In summer (June -August), however, both aerosol number concentration and DPR value were decreased in all size bins due to the influences of relatively clean maritime airmass and frequent precipitations. In autumn (September - November), the particle number concentration in all size bins was the lowest. To classify the aerosol types, we investigate particle number and volume size distributions and DPR value for clean, dust-dominant and anthropogenic pollution-dominant cases, which were selected by PM10, PM2.5 mass concentrations and its ratio, because those parameters are clearly different among aerosol types (Kobayashi et al., 2014, Pan et al., 2016). Non-spherical coarse mode particles (Dp > 2.5 μm, 0.1 < DPR < 0.6) were dominantly observed during the dust-dominant period, while both spherical fine mode and coarse mode particles (Dp < 1 μm and Dp = 2-4 μm, DPR < 0.1) were dominantly appeared during the pollution event. The aerosol type classifications with these criteria values were successfully applied to the extreme Asian dust event from February 22 to 24, 2015. The results showed that pollution-dominant airmass preceded by the appearance of a major mineral dust plume. Co-located aerosol lidar measurements also revealed that spherical pollution particles were observed near the surface prior to a major plume of non-spherical mineral dust.

Improving visual spatial working memory in younger and older adults: effects of cross-modal cues.

PubMed

Curtis, Ashley F; Turner, Gary R; Park, Norman W; Murtha, Susan J E

2017-11-06

Spatially informative auditory and vibrotactile (cross-modal) cues can facilitate attention but little is known about how similar cues influence visual spatial working memory (WM) across the adult lifespan. We investigated the effects of cues (spatially informative or alerting pre-cues vs. no cues), cue modality (auditory vs. vibrotactile vs. visual), memory array size (four vs. six items), and maintenance delay (900 vs. 1800 ms) on visual spatial location WM recognition accuracy in younger adults (YA) and older adults (OA). We observed a significant interaction between spatially informative pre-cue type, array size, and delay. OA and YA benefitted equally from spatially informative pre-cues, suggesting that attentional orienting prior to WM encoding, regardless of cue modality, is preserved with age.  Contrary to predictions, alerting pre-cues generally impaired performance in both age groups, suggesting that maintaining a vigilant state of arousal by facilitating the alerting attention system does not help visual spatial location WM.

Workplace discrimination and disfigurement: the national EEOC ADA research project.

PubMed

Tartaglia, Alexander; McMahon, Brian T; West, Steven L; Belongia, Lisa

2005-01-01

Using the Integrated Mission System of the Equal Employment Opportunity Commission, the employment discrimination experience of Americans with disfigurement is documented. Key dimensions of workplace discrimination involving Americans with disfigurement and persons with missing limbs are compared and contrasted. Specifically, the researchers examine demographic characteristics of Charging Parties; the industry designation, location and size of Respondents/employers; the discrimination Issue (i.e., type of adverse action) alleged to occur; and the legal outcome or Resolution of these allegations. Charging Parties with disfigurement who are female or between 30 and 39 years of age are more likely to encounter employment discrimination than their counterparts with missing limbs. Harassment and Non-wage Benefits are the Issues that emerge in higher proportion. Allegations derived from persons with disfigurement are more common in among mid-size employers, those located in the South, or those in Retail or Service industries. Following investigation, allegations derived from persons with disfigurement are less likely to have Merit Resolutions than those brought by Charging Parties with missing limbs.

21 CFR 1302.04 - Location and size of symbol on label and labeling.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Location and size of symbol on label and labeling. 1302.04 Section 1302.04 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE LABELING AND PACKAGING REQUIREMENTS FOR CONTROLLED SUBSTANCES § 1302.04 Location and size of symbol on label...

21 CFR 1302.04 - Location and size of symbol on label and labeling.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 9 2011-04-01 2011-04-01 false Location and size of symbol on label and labeling. 1302.04 Section 1302.04 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE LABELING AND PACKAGING REQUIREMENTS FOR CONTROLLED SUBSTANCES § 1302.04 Location and size of symbol on label...

21 CFR 1302.04 - Location and size of symbol on label and labeling.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 9 2012-04-01 2012-04-01 false Location and size of symbol on label and labeling. 1302.04 Section 1302.04 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE LABELING AND PACKAGING REQUIREMENTS FOR CONTROLLED SUBSTANCES § 1302.04 Location and size of symbol on label...

Assessment at full scale of exhaust nozzle-to-wing size on STOL-OTW acoustic characteristics

NASA Technical Reports Server (NTRS)

Von Glahn, U.; Groesbeck, D.

1979-01-01

On the basis of static zero/acoustic data obtained at model scale, the effect of exhaust nozzle size on flyover noise is evaluated at full scale for different STOL-OTW nozzle configurations. Three types of nozzles are evaluated: a circular/deflector nozzle mounted above the wing, a slot/deflector nozzle mounted on the wing, and a slot nozzle mounted on the wing. The nozzle exhaust plane location, measured from the wing leading edge was varied from 10 to 46 percent of the wing chord (flaps retracted). Flap angles of 20 deg (takeoff) and 60 deg (approach) are included in the study. Initially, perceived noise levels (PNL) are calculated as a function of flyover distance at 152 m altitude. From these plots static EPNL values, defined as flyover relative noise levels, then are obtained as functions of nozzle size for equal aerodynamic performance (lift and thrust). On the basis of these calculations, the acoustic benefits attributable to nozzle size relative to a given wing chord size are assessed.

Assessment at full scale of exhaust nozzle to wing size on STOL-OTW acoustic characteristics

NASA Technical Reports Server (NTRS)

Vonglahn, U.; Grosbeck, D.

1979-01-01

On the basis of static aero/acoustic data obtained at model scale, the effect of exhaust nozzle size on flyover noise is evaluated at full scale for different STOL-OTW nozzle configurations. Three types of nozzles are evaluated: a circular/deflector nozzle mounted above the wing; a slot/deflector nozzle mounted on the wing; and a slot nozzle mounted on the wing. The nozzle exhaust plane location, measured from the wing leading edge, was varied from 10 to 46 percent of the wing chord (flaps retracted). Flap angles of 20 deg (takeoff) and 60 deg (approach) are included in the study. Initially, perceived noise levels (PNL) are calculated as a function flyover distance at 152m altitude. From these plots, static EPNL values (defined as flyover relative noise levels), are obtained as functions of nozzle size for equal aerodynamic performance (lift and thrust). The acoustic benefits attributable to nozzle size relative to a given wing chord size are assessed.

Prospective Computed Tomographic Analysis of Osteochondral Lesions of the Ankle Joint Associated With Ankle Fractures.

PubMed

Nosewicz, Tomasz L; Beerekamp, M Suzan H; De Muinck Keizer, Robert-Jan O; Schepers, Tim; Maas, Mario; Niek van Dijk, C; Goslings, J Carel

2016-08-01

Osteochondral lesions (OCLs) associated with ankle fracture correlate with unfavorable outcome. The goals of this study were to detect OCLs following ankle fracture, to associate fracture type to OCLs and to investigate whether OCLs affect clinical outcome. 100 ankle fractures requiring operative treatment were prospectively included (46 men, 54 women; mean age 44 ± 14 years, range 20-77). All ankle fractures (conventional radiography; 71 Weber B, 22 Weber C, 1 Weber A, 4 isolated medial malleolus and 2 isolated posterior malleolus fractures) were treated by open reduction and internal fixation. Multidetector computed tomography (CT) was performed postoperatively. For each OCL, the location, size, and Loomer OCL classification (CT modified Berndt and Harty classification) were determined. The subjective Foot and Ankle Outcome Scoring (FAOS) was used for clinical outcome at 1 year. OCLs were found in 10/100 ankle fractures (10.0%). All OCLs were solitary talar lesions. Four OCLs were located posteromedial, 4 posterolateral, 1 anterolateral, and 1 anteromedial. There were 2 type I OCLs (subchondral compression), 6 type II OCLs (partial, nondisplaced fracture) and 2 type IV OCLs (displaced fracture). Mean OCL size (largest diameter) was 4.4 ± 1.7 mm (range, 1.7 mm to 6.2 mm). Chi-square analysis showed no significant association between ankle fracture type and occurrence of OCLs. OCLs did occur only in Lauge-Hansen stage III/IV ankle fractures. There were no significant differences in FAOS outcome between patients with or without OCLs. Ten percent of investigated ankle fractures had associated OCLs on CT. Although no significant association between fracture type and OCL was found, OCLs only occurred in Lauge-Hansen stage III/IV ankle fractures. With the numbers available, OCLs did not significantly affect clinical outcome at 1 year according to FAOS. Level IV, observational study. © The Author(s) 2016.

Two-point method uncertainty during control and measurement of cylindrical element diameters

NASA Astrophysics Data System (ADS)

Glukhov, V. I.; Shalay, V. V.; Radev, H.

2018-04-01

The topic of the article is devoted to the urgent problem of the reliability of technical products geometric specifications measurements. The purpose of the article is to improve the quality of parts linear sizes control by the two-point measurement method. The article task is to investigate methodical extended uncertainties in measuring cylindrical element linear sizes. The investigation method is a geometric modeling of the element surfaces shape and location deviations in a rectangular coordinate system. The studies were carried out for elements of various service use, taking into account their informativeness, corresponding to the kinematic pairs classes in theoretical mechanics and the number of constrained degrees of freedom in the datum element function. Cylindrical elements with informativity of 4, 2, 1 and θ (zero) were investigated. The uncertainties estimation of in two-point measurements was made by comparing the results of of linear dimensions measurements with the functional diameters maximum and minimum of the element material. Methodical uncertainty is formed when cylindrical elements with maximum informativeness have shape deviations of the cut and the curvature types. Methodical uncertainty is formed by measuring the element average size for all types of shape deviations. The two-point measurement method cannot take into account the location deviations of a dimensional element, so its use for elements with informativeness less than the maximum creates unacceptable methodical uncertainties in measurements of the maximum, minimum and medium linear dimensions. Similar methodical uncertainties also exist in the arbitration control of the linear dimensions of the cylindrical elements by limiting two-point gauges.

Defective interfering particles of poliovirus: mapping of the deletion and evidence that the deletions in the genomes of DI(1), (2), and (3) are located in the same region

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nomoto, A.; Jacobson, A.; Lee, Y.F.

1979-01-01

The deletions in RNAs of three defective interfering (DI) particles of poliovirus type 1 have been located and their approximate extent determined by three methods. (1) Digestion with RNase III of DI RNAs yields the same 3'-terminal fragments as digestion wth RNase III of standard virus RNA. The longest 3'-terminal located in the 5'-terminal half of the polio genome. (2) Fingerprints of RNase T/sub 1/-resistant oligonucleotides of all three DI RNAs are identical and lack four large oligonucleotides as compared to the fingerprints of standard virus, an observation suggesting that the deletions in all three DI RNAs are located inmore » the same reregion of the viral genome. The deletion-specific oligonucleotides have also been shown to be within the 5'-terminal half of the viral genome by alkali fragmentation of the RNA and fingerprinting poly(A)-linked (3'-terminal) fragments of decreasing size. (3) Virion RNA of DI(2) particles was annealed with denatured double-stranded RNA (RF) of standard virus and the hybrid heteroduplex molcules examined in the electron microscope. A single loop, approximately 900 nucleotides long and 20% from one end of the molecules, was observed. Both the size and extent of individual deletions is somewhat variable in different hetereoduplex molecules, an observation suggesting heterogeneity in the size of the deletion in RNA of the DI(2) population. Our data show that the DI RNAs of poliovirus contain an internal deletion in that region of the viral genome known to specify the capsid polypeptides. This result provides an explanation as to why poliovirus DI particles are unable to synthesize viral coat proteins.« less

A Low-Speed Experimental Investigation of the Effect of a Sandpaper Type of Roughness on Boundary-Layer Transition

NASA Technical Reports Server (NTRS)

Von Doenhoff, Albert E; Horton, Elmer A

1958-01-01

An investigation was made in the Langley low-turbulence pressure tunnel to determine the effect of size and location of a sandpaper type of roughness on the Reynolds number for transition. Transition was observed by means of a hot-wire anemometer located at various chordwise stations for each position of the roughness. These observations indicated that when the roughness is sufficiently submerged in the boundary layer to provide a substantially linear variation of boundary-layer velocity with distance from the surface up to the top of the roughness, turbulent "spots" begin to appear immediately behind the roughness when the Reynolds number based on the velocity at the top of the roughness height exceeds a value of approximately 600. At Reynolds numbers even slightly below the critical value (value for transition), the sandpaper type of roughness introduced no measurable disturbances into the laminar layer downstream of the roughness. The extent of the roughness area does not appear to have an important effect on the critical value of the roughness Reynolds number.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mehra, S.; Bryce, T.

Sedco Forex has recently completed a new land drilling rig, currently deployed in Gabon, that integrates well construction activities with multiskilling to create cost savings across the board in drilling operations. Historically, operators have produced a comprehensive tender package specifying strictly the type and size of individual rig components and the number of personnel required to drill. In this case, the drilling contractor provides a fit-for-purpose rig, consistent with field location, well profile, operator`s priorities, and local constraints.

Virus Information Update CIAC-2301

DTIC Science & Technology

1998-05-21

a tune through a sound card. Byway is reported to be in the wild internationally, especially in Venezuela, Mexico , Bulgaria, UK and USA. REMOVAL NOTE...1482, Varicella Type: Program. Disk Location: Features: Damage: Size: See Also: Notes: v6-146: This virus was written to hurt users of the TBCLEAN...antivirus package. If you have a file infected with the Varicella virus, and if you tried to clean this virus infected file with tbclean, what would

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Surendra; Jauriqui, Leanne; Sloan, Trista

We have used Process Compensated Resonant Testing (PCRT) for studying structural integrity and functional performance of ceramic balls used in various auxiliary power units (APUs), propulsion engines, and defense and space missiles. The results show that PCRT is successful in sorting acceptable parts from parts with defects such as micro-structural changes, C-cracks, and scuffs. However, PCRT suffers from limitations, generally not determining the type, size or location of the anomaly. The pursuit of improvements to PCRT is an on-going process.

Dental Education in Florida. A Study Prepared in Response to Appropriation Item 450 of the 1983 General Appropriations Act (Chapter 83-300, Laws of Florida). 1984--Report 4.

ERIC Educational Resources Information Center

Florida State Postsecondary Education Commission, Tallahassee.

The situation regarding dental education programs in Florida was studied, with attention to the type and size of programs needed to meet state needs, the geographic location of dental programs, funding and tuition policies, and the state's responsibility to provide an opportunity for its residents to participate in these educational programs. It…

Improving the Cost Efficiency and Readiness of MC-130 Aircrew Training: A Case Study

DTIC Science & Technology

2015-01-01

51 Jiang, Changbing, "A reliable solver of Euclidean traveling salesman problems with Microsoft excel add-in tools for small-size systems...DisplayPage.aspx?DocType=Reference&ItemId=+++1 343364&Pubabbrev=JAWA 124 Jiang, Changbing, "A Reliable Solver of Euclidean Traveling Salesman Problems with...49 Figure 4.5 Training Resources Locations Traveling Salesperson Problem In order to participate in training, aircrews must fly to the

Methodological concerns for meta-analyses of meditation: Comment on Sedlmeier et al. (2012).

PubMed

Orme-Johnson, David W; Dillbeck, Michael C

2014-03-01

We commend Sedlmeier et al. (2012) for their significant undertaking of meta-analysis of all meditation types on all psychological variables, but additional analyses may modify some of their conclusions. Whereas they suggest from visual inspection of funnel diagrams that there may be publication bias of underreporting low-effect studies on the Transcendental Meditation (TM) technique, quantitative tests do not indicate the presence of bias for any type of meditation. We additionally found that there was no significant difference in effect sizes between studies originating from researchers affiliated with a TM organization and studies from other universities. We found that comparison of different types of meditation on their global index was confounded because their global index aggregated different sets of variables for the different groups. That is, using composite indices that only aggregated variables for which each group had at least 3 studies confirmed the authors' conclusion that effect sizes for different research designs were not different, but found that effect sizes for the TM technique were significantly larger than effect sizes for mindfulness meditation or other meditations. We also located 35 studies on the TM technique that appear to meet the authors' inclusion criteria that were missed by their meta-analysis, and several others on important psychosocial behavioral variables, such as job performance, substance abuse, and prison recidivism that were not reviewed. In addition, we suggest that future meta-analyses on psychological variables include cross-validating physiological studies.

Immunocytochemical localization of metabotropic (mGluR2/3 and mGluR4a) and ionotropic (GluR2/3) glutamate receptors in adrenal medullary ganglion cells.

PubMed

Sarría, R; Díez, J; Losada, J; Doñate-Oliver, F; Kuhn, R; Grandes, P

2006-02-01

The localization of metabotropic glutamate receptors of groups II (mGluR2/3) and III (mGluR4a) and the subunits 2 and 3 of alfa-amino-3-hydroxy-5-methyl-4-isoxazolepropionic acid (AMPA) ionotropic glutamate receptors (GluR2/3) was investigated with immunocytochemical methods in the rat adrenal gland. MGluR2/3, mGluR4a and GluR2/3 immunoreactivities were observed in large-sized, centrally located type I adrenal medullary ganglion neurons. Furthermore, the small-sized type II adrenal ganglion neurons identified by their immunoreactivity to brain nitric oxide synthase (bNOS), also expressed mGluR2/3, mGluR4a and GluR2/3. These cells were disposed in the peripheral portion of the adrenal medulla. None of the type I neurons were positively labeled for bNOS. These morphological observations suggest that activation of glutamate receptors in ganglion neurons may be instrumental in the control of adrenal endocrine systems as well as blood regulation.

Endoscopic ultrasound-guided fine-needle aspiration needles: which one and in what situation?

PubMed

Karadsheh, Zeid; Al-Haddad, Mohammad

2014-01-01

Endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA) is increasingly used as a diagnostic and therapeutic tool for pancreatic and other gastrointestinal disorders. Several factors affect the outcome of EUS-FNA, one of which is needle size. The decision to use a specific needle depends on factors including location, consistency, and type of the lesion; presence of onsite cytopathologist; and need for additional tissue procurement for histology. This review provides a balanced perspective on the use of different needle sizes available, highlighting the differences among them and potential niche applications of each to maximize diagnostic yield of EUS-FNA. Copyright © 2014 Elsevier Inc. All rights reserved.

Studies on hand-held visual communication device for the deaf and speech-impaired I. Visual display window size.

PubMed

Thurlow, W R

1980-01-01

Messages were presented which moved from right to left along an electronic alphabetic display which was varied in "window" size from 4 through 32 letter spaces. Deaf subjects signed the messages they perceived. Relatively few errors were made even at the highest rate of presentation, which corresponded to a typing rate of 60 words/min. It is concluded that many deaf persons can make effective use of a small visual display. A reduced cost is then possible for visual communication instruments for these people through reduced display size. Deaf subjects who can profit from a small display can be located by a sentence test administered by tape recorder which drives the display of the communication device by means of the standard code of the deaf teletype network.

Chondromyxoid fibroma.

PubMed

Baron, R L; Galinski, A W; Vlahos, M; Heiring, M

1996-05-01

Chondromyxoid fibroma is a rare benign tumor derived from cartilage. The classic site of involvement is usually the metaphyseal ends of the long tubular bones, such as the tibia. The majority of these tumors are seen in the lower extremities during the second and third decades of life. Local recurrence of the tumor in bone is not uncommon, while soft tissue recurrence is less frequent. Most younger patients and those with recurrent tumors tend to have the mucinous type. This case is somewhat classic in nature. The tumor was originally seen in the second decade of life and was of the mucinoid type. Bone grafting was necessary because of the size and location of the tumor.

Energy data report: Solar collector manufacturing activity, July - December 1980

NASA Astrophysics Data System (ADS)

1981-03-01

Statistics on solar collector manufacturing activity for both solar thermal collectors and photovoltaic modules through 1980 are presented. Summary data are given for the number of manufacturers and collector area produced each year from 1974 through 1980; data for collector type are included, i.e., low temperature or medium temperature and special collectors. Producer shipments are tabulated according to location of company headquarters, producer size, and collector types. headquarters The number of companies engaged in activities related to solar collector manufacturing for 1978 through 1980 are listed; and the number of manufacturers and market sector are tabulated for photovoltaic modules manufacturing activities.

New Late Gene, dar, Involved in DNA Replication of Bacteriophage T4 I. Isolation, Characterization, and Genetic Location.

PubMed

Wu, J R; Yeh, Y C

1975-05-01

Suppressors of gene 59-defective mutants were isolated by screening spontaneous, temperature-sensitive (ts) revertants of the amber mutant, amC5, in gene 59. Six ts revertants were isolated. No gene 59-defective ts recombinant was obtained by crossing each ts revertant with the wild type, T4D. However, suppressors of gene 59-defective mutants were obtained from two of these ts revertants. These suppressor mutants are referred to as dar (DNA arrested restoration). dar mutants specifically restored the abnormalities, both in DNA synthesis and burst size, caused by gene 59-defective mutants to normal levels. It is unlikely that dar mutants are nonsense suppressors since theý failed to suppress amber mutations in 11 other genes investigated. The genetic expression of dar is controlled by gene 55; therefore, dar is a late gene. The genetic location of dar has been mapped between genes 24 and 25, a region contiguous to late genes. dar appears to be another nonessential gene of T4 since burst sizes of dar were almost identical to those of the wild type. Mutations in dar did not affect genetic recombination and repair of UV-damaged DNA, but caused a sensitivity to hydroxyurea in progeny formation. The effect of the dar mutation on host DNA degradation cannot account for its hydroxyurea sensitivity. dar mutant alleles were recessive to the wild-type allele as judged by restoration of arrested DNA synthesis. The possible mechanisms for the suppression of defects in gene 59 are discussed.

Perception while watching movies: Effects of physical screen size and scene type

PubMed Central

Troscianko, Tom; Meese, Timothy S.; Hinde, Stephen

2012-01-01

Over the last decade, television screens and display monitors have increased in size considerably, but has this improved our televisual experience? Our working hypothesis was that the audiences adopt a general strategy that “bigger is better.” However, as our visual perceptions do not tap directly into basic retinal image properties such as retinal image size (C. A. Burbeck, 1987), we wondered whether object size itself might be an important factor. To test this, we needed a task that would tap into the subjective experiences of participants watching a movie on different-sized displays with the same retinal subtense. Our participants used a line bisection task to self-report their level of “presence” (i.e., their involvement with the movie) at several target locations that were probed in a 45-min section of the movie “The Good, The Bad, and The Ugly.” Measures of pupil dilation and reaction time to the probes were also obtained. In Experiment 1, we found that subjective ratings of presence increased with physical screen size, supporting our hypothesis. Face scenes also produced higher presence scores than landscape scenes for both screen sizes. In Experiment 2, reaction time and pupil dilation results showed the same trends as the presence ratings and pupil dilation correlated with presence ratings, providing some validation of the method. Overall, the results suggest that real-time measures of subjective presence might be a valuable tool for measuring audience experience for different types of (i) display and (ii) audiovisual material. PMID:23145293

Co-precipitated and collocated carbides and Cu-rich precipitates in a Fe-Cu steel characterized by atom-probe tomography.

PubMed

Kolli, R Prakash; Seidman, David N

2014-12-01

The composition of co-precipitated and collocated NbC carbide precipitates, Fe3C iron carbide (cementite), and Cu-rich precipitates are studied experimentally by atom-probe tomography (APT). The Cu-rich precipitates located at a grain boundary (GB) are also studied. The APT results for the carbides are supplemented with computational thermodynamics predictions of composition at thermodynamic equilibrium. Two types of NbC carbide precipitates are distinguished based on their stoichiometric ratio and size. The Cu-rich precipitates at the periphery of the iron carbide and at the GB are larger than those distributed in the α-Fe (body-centered cubic) matrix, which is attributed to short-circuit diffusion of Cu along the GB. Manganese segregation is not observed at the heterophase interfaces of the Cu-rich precipitates that are located at the periphery of the iron carbide or at the GB, which is unlike those located at the edge of the NbC carbide precipitates or distributed in the α-Fe matrix. This suggests the presence of two populations of NiAl-type (B2 structure) phases at the heterophase interfaces in multicomponent Fe-Cu steels.

Computer automation of ultrasonic testing. [inspection of ultrasonic welding

NASA Technical Reports Server (NTRS)

Yee, B. G. W.; Kerlin, E. E.; Gardner, A. H.; Dunmyer, D.; Wells, T. G.; Robinson, A. R.; Kunselman, J. S.; Walker, T. C.

1974-01-01

Report describes a prototype computer-automated ultrasonic system developed for the inspection of weldments. This system can be operated in three modes: manual, automatic, and computer-controlled. In the computer-controlled mode, the system will automatically acquire, process, analyze, store, and display ultrasonic inspection data in real-time. Flaw size (in cross-section), location (depth), and type (porosity-like or crack-like) can be automatically discerned and displayed. The results and pertinent parameters are recorded.

Conversion of a Micro, Glow-Ignition, Two-Stroke Engine from Nitromethane-Methanol Blend Fuel to Military Jet Propellant (JP-8)

DTIC Science & Technology

2012-01-01

Table 10-4: Selected Birk polyimide heater sizes, resistances and locations [37] ........................ 79 Table 10-5: Final starting tests with (3...damage, and fire are prevalent. Kerosene type fuels are also cheaper and more common than nitromethane-methanol blend fuels. One final note is...diesel fuel was changed to produce lower emissions, the abrasiveness of diesel fuel increased. This was especially problematic for the new high

On the Sequence-Directed Nature of Human Gene Mutation: The Role of Genomic Architecture and the Local DNA Sequence Environment in Mediating Gene Mutations Underlying Human Inherited Disease

PubMed Central

Cooper, David N.; Bacolla, Albino; Férec, Claude; Vasquez, Karen M.; Kehrer-Sawatzki, Hildegard; Chen, Jian-Min

2011-01-01

Different types of human gene mutation may vary in size, from structural variants (SVs) to single base-pair substitutions, but what they all have in common is that their nature, size and location are often determined either by specific characteristics of the local DNA sequence environment or by higher-order features of the genomic architecture. The human genome is now recognized to contain ‘pervasive architectural flaws’ in that certain DNA sequences are inherently mutation-prone by virtue of their base composition, sequence repetitivity and/or epigenetic modification. Here we explore how the nature, location and frequency of different types of mutation causing inherited disease are shaped in large part, and often in remarkably predictable ways, by the local DNA sequence environment. The mutability of a given gene or genomic region may also be influenced indirectly by a variety of non-canonical (non-B) secondary structures whose formation is facilitated by the underlying DNA sequence. Since these non-B DNA structures can interfere with subsequent DNA replication and repair, and may serve to increase mutation frequencies in generalized fashion (i.e. both in the context of subtle mutations and SVs), they have the potential to serve as a unifying concept in studies of mutational mechanisms underlying human inherited disease. PMID:21853507

Selection of forest canopy gaps by male Cerulean Warblers in West Virginia

USGS Publications Warehouse

Perkins, Kelly A.; Wood, Petra Bohall

2014-01-01

Forest openings, or canopy gaps, are an important resource for many forest songbirds, such as Cerulean Warblers (Setophaga cerulea). We examined canopy gap selection by this declining species to determine if male Cerulean Warblers selected particular sizes, vegetative heights, or types of gaps. We tested whether these parameters differed among territories, territory core areas, and randomly-placed sample plots. We used enhanced territory mapping techniques (burst sampling) to define habitat use within the territory. Canopy gap densities were higher within core areas of territories than within territories or random plots, indicating that Cerulean Warblers selected habitat within their territories with the highest gap densities. Selection of regenerating gaps with woody vegetation >12 m within the gap, and canopy heights >24 m surrounding the gap, occurred within territory core areas. These findings differed between two sites indicating that gap selection may vary based on forest structure. Differences were also found regarding the placement of territories with respect to gaps. Larger gaps, such as wildlife food plots, were located on the periphery of territories more often than other types and sizes of gaps, while smaller gaps, such as treefalls, were located within territory boundaries more often than expected. The creations of smaller canopy gaps, <100 m2, within dense stands are likely compatible with forest management for this species.

Detection of orthopaedic implants by airport metal detectors.

PubMed

Obremskey, William T; Austin, Tom; Crosby, Colin; Driver, Robin; Kurtz, Will; Shuler, Franklin; Kregor, Philip

2007-02-01

To report the effect of patient's body mass index (BMI), implant type, size, location, number, and material on detection by certified Transportation Security Administration (TSA) and Federal Aviation Administration (FAA) airport metal detectors set to today's standard sensitivity. Retrospective clinical study. Level 1 university trauma center. Ninety-six regularly scheduled trauma clinic patients with a wide variety of orthopaedic implants were enrolled in the study from August 2004 through December 2004. Patients walked through an airport arch metal detector and were also wanded with a handheld metal detector. Detection of implants by arch detector or wand was recorded. We also gathered information regarding BMI, location of implants, type, metal composition, and size. All unilateral prostheses (8/8) and bilateral prostheses (1/1) were detected. Subjects with 4 or fewer screws and no other implants were never detected by the arch metal detector (0/7). For the remaining 78 subjects, the 2 best predictors of detection by the arch were having plates of length >10 holes and having titanium nails (P < 0.001 for each predictor, Wald's test for effects in a logistic model). Prostheses, plates of length >10 holes, and titanium nails were the best predictors of detection by the arch. These 3 factors accounted for 42 of the 43 detections by the arch. Body mass index was not shown to affect detectability of orthopaedic implants.

HVDC Ground Electrodes and Tectonic Setting

NASA Astrophysics Data System (ADS)

Freire, P. F.; Pereira, S. Y.

2017-12-01

Ground electrodes in HVDC transmission are huge grounding systems for the DC part of the converter substation, about 1 km wide, sized to inject in the ground DC currents up to 3.5 kA. This work presents an analysis of how the tectonic setting at converter substation location is determinant for the search of the best electrode location (Site Selection) and on its design and performance. It will briefly present the author experience on HVDC electrode design, summarized as follows: Itaipu - Foz do Iguaçu electrodes (transmitter side) located in the middle of Paraná Sedimentary Basin, and Ibiúna electrodes (receiving side) on the border of the basin, 6 km from the geological strike, where the crystalline basement outcrops in São Paulo state; Madeira River - North electrodes (transmitting side) located on the Northwest border of South Amazon Craton, where the crystalline basement is below a shallow sediments layer, and South electrodes (receiving side) located within Paraná Sedimentary Basin; Chile - electrodes located on the Andean forearc, where the Nazca Plate plunges under the South American Plate; Kenya - Ethiopia - electrodes located in the African Rift; Belo Monte - North electrodes (transmitter side) located within the Amazonian Sedimentary Basin, about 35 km of its South border, and South electrodes (receiving side) within Paraná Sedimentary Basin (bipole 1) and on crystalline metamorphic terrain "Brasília Belt" (bipole 2). This diversity of geological conditions results on ground electrodes of different topologies and dimensions, with quite different electrical and thermal performances. A brief study of the geology of the converter stations regions, the so-called Desktop Study, allows for the preview of several important parameters for the site selection and design of the electrodes, such as localization, type, size and estimate of the interference area, which are important predictors of the investment to be made and indications of the design to be developed.

Molecular Characterization of Bovine SMO Gene and Effects of Its Genetic Variations on Body Size Traits in Qinchuan Cattle (Bos taurus).

PubMed

Zhang, Ya-Ran; Gui, Lin-Sheng; Li, Yao-Kun; Jiang, Bi-Jie; Wang, Hong-Cheng; Zhang, Ying-Ying; Zan, Lin-Sen

2015-07-27

Smoothened (Smo)-mediated Hedgehog (Hh) signaling pathway governs the patterning, morphogenesis and growth of many different regions within animal body plans. This study evaluated the effects of genetic variations of the bovine SMO gene on economically important body size traits in Chinese Qinchuan cattle. Altogether, eight single nucleotide polymorphisms (SNPs: 1-8) were identified and genotyped via direct sequencing covering most of the coding region and 3'UTR of the bovine SMO gene. Both the p.698Ser.>Ser. synonymous mutation resulted from SNP1 and the p.700Ser.>Pro. non-synonymous mutation caused by SNP2 mapped to the intracellular C-terminal tail of bovine Smo protein; the other six SNPs were non-coding variants located in the 3'UTR. The linkage disequilibrium was analyzed, and five haplotypes were discovered in 520 Qinchuan cattle. Association analyses showed that SNP2, SNP3/5, SNP4 and SNP6/7 were significantly associated with some body size traits (p < 0.05) except SNP1/8 (p > 0.05). Meanwhile, cattle with wild-type combined haplotype Hap1/Hap1 had significantly (p < 0.05) greater body length than those with Hap2/Hap2. Our results indicate that variations in the SMO gene could affect body size traits of Qinchuan cattle, and the wild-type haplotype Hap1 together with the wild-type alleles of these detected SNPs in the SMO gene could be used to breed cattle with superior body size traits. Therefore, our results could be helpful for marker-assisted selection in beef cattle breeding programs.

Molecular Characterization of Bovine SMO Gene and Effects of Its Genetic Variations on Body Size Traits in Qinchuan Cattle (Bos taurus)

PubMed Central

Zhang, Ya-Ran; Gui, Lin-Sheng; Li, Yao-Kun; Jiang, Bi-Jie; Wang, Hong-Cheng; Zhang, Ying-Ying; Zan, Lin-Sen

2015-01-01

Smoothened (Smo)-mediated Hedgehog (Hh) signaling pathway governs the patterning, morphogenesis and growth of many different regions within animal body plans. This study evaluated the effects of genetic variations of the bovine SMO gene on economically important body size traits in Chinese Qinchuan cattle. Altogether, eight single nucleotide polymorphisms (SNPs: 1–8) were identified and genotyped via direct sequencing covering most of the coding region and 3ʹUTR of the bovine SMO gene. Both the p.698Ser.>Ser. synonymous mutation resulted from SNP1 and the p.700Ser.>Pro. non-synonymous mutation caused by SNP2 mapped to the intracellular C-terminal tail of bovine Smo protein; the other six SNPs were non-coding variants located in the 3ʹUTR. The linkage disequilibrium was analyzed, and five haplotypes were discovered in 520 Qinchuan cattle. Association analyses showed that SNP2, SNP3/5, SNP4 and SNP6/7 were significantly associated with some body size traits (p < 0.05) except SNP1/8 (p > 0.05). Meanwhile, cattle with wild-type combined haplotype Hap1/Hap1 had significantly (p < 0.05) greater body length than those with Hap2/Hap2. Our results indicate that variations in the SMO gene could affect body size traits of Qinchuan cattle, and the wild-type haplotype Hap1 together with the wild-type alleles of these detected SNPs in the SMO gene could be used to breed cattle with superior body size traits. Therefore, our results could be helpful for marker-assisted selection in beef cattle breeding programs. PMID:26225956

Growing Mediums in Different Environments for Sunflower and Cilantro Microgreens

NASA Astrophysics Data System (ADS)

Tran, B.; Gonzalez, O.

2016-12-01

The purpose of this experiment is to investigate the growth and subsequent harvest of young seedlings known as microgreens, which have expanded into a very profitable market. The goal of the experiment is to discover whether the nutrients, soil quality and climate influences the quality, flavor, and yield of the microgreens. To conduct this experiment, locations and soil types were chosen; the locations consisted of a greenhouse (an enclosed space which held consistent sunlight, warmth, and humidity) and a lath house (a somewhat shaded location that was open to the elements as well as temperature changes), while compost, Quick Root (a growing medium that is relatively devoid of nutrients), and a combination of the two is used in this experiment. This meant that a total of six different combinations could be tested. Along with that, two different seeds were selected, sunflower seeds and cilantro seeds. Each of the results are mainly influenced by the soil type, and a partial influence by the climate. Compost has an extreme lack in growth and did not produce enough plants to record in general. The Quick Root results show only a burst of growth would occur; also, the plants did not have a strong taste, but did grow slightly quicker within the greenhouse. Another advantage to the Quick Root results is that the root size nearly tripled compared to the 50/50 root size. 50/50 holds the strongest results i.e., growth consistency and holds a stronger taste. Originally, there was an attempt to grow sunflowers uncovered, but was not attempted again due to poor results. Overall the 50/50 held a stronger growth and taste, but also would easily excel in the long run compared to the Quick Root and the compost.

The Influence of Study-Level Inference Models and Study Set Size on Coordinate-Based fMRI Meta-Analyses

PubMed Central

Bossier, Han; Seurinck, Ruth; Kühn, Simone; Banaschewski, Tobias; Barker, Gareth J.; Bokde, Arun L. W.; Martinot, Jean-Luc; Lemaitre, Herve; Paus, Tomáš; Millenet, Sabina; Moerkerke, Beatrijs

2018-01-01

Given the increasing amount of neuroimaging studies, there is a growing need to summarize published results. Coordinate-based meta-analyses use the locations of statistically significant local maxima with possibly the associated effect sizes to aggregate studies. In this paper, we investigate the influence of key characteristics of a coordinate-based meta-analysis on (1) the balance between false and true positives and (2) the activation reliability of the outcome from a coordinate-based meta-analysis. More particularly, we consider the influence of the chosen group level model at the study level [fixed effects, ordinary least squares (OLS), or mixed effects models], the type of coordinate-based meta-analysis [Activation Likelihood Estimation (ALE) that only uses peak locations, fixed effects, and random effects meta-analysis that take into account both peak location and height] and the amount of studies included in the analysis (from 10 to 35). To do this, we apply a resampling scheme on a large dataset (N = 1,400) to create a test condition and compare this with an independent evaluation condition. The test condition corresponds to subsampling participants into studies and combine these using meta-analyses. The evaluation condition corresponds to a high-powered group analysis. We observe the best performance when using mixed effects models in individual studies combined with a random effects meta-analysis. Moreover the performance increases with the number of studies included in the meta-analysis. When peak height is not taken into consideration, we show that the popular ALE procedure is a good alternative in terms of the balance between type I and II errors. However, it requires more studies compared to other procedures in terms of activation reliability. Finally, we discuss the differences, interpretations, and limitations of our results. PMID:29403344

Examining a shrinking rustbelt city: A case of Binghamton, NY (1990 - 2010)

NASA Astrophysics Data System (ADS)

Park, Paul Sung-Pyo

Shrinking cities are locations that have experienced population and economic loss. Each shrinking city is unique in the influential characteristics that result in loss, however, patterns of the contemporary city is highly based on economic changes. The impact of shrinking cities is a global phenomenon not only limited to the U.S. or the developed world. However, among large shrinking cities of the world, 25% are located in the U.S. Therefore, it is of utter importance to understand and examine these locations. The connection of spectral findings of a shrinking "Rustbelt" city of Binghamton, NY using a multilayer perceptron (MLP) artificial neural network (ANN) mean of classification was made with spatial findings of demographic and socioeconomic status of the local population. This resulted in a high scale classification of urban ecozones, which created the boundaries for examining the changes in population size and the types of individuals associated with these populations.

Genomic Diversity of Type B3 Bacteriophages of Caulobacter crescentus.

PubMed

Ash, Kurt T; Drake, Kristina M; Gibbs, Whitney S; Ely, Bert

2017-07-01

The genomes of the type B3 bacteriophages that infect Caulobacter crescentus are among the largest phage genomes thus far deposited into GenBank with sizes over 200 kb. In this study, we introduce six new bacteriophage genomes which were obtained from phage collected from various water systems in the southeastern United States and from tropical locations across the globe. A comparative analysis of the 12 available genomes revealed a "core genome" which accounts for roughly 1/3 of these bacteriophage genomes and is predominately localized to the head, tail, and lysis gene regions. Despite being isolated from geographically distinct locations, the genomes of these bacteriophages are highly conserved in both genome sequence and gene order. We also identified the insertions, deletions, translocations, and horizontal gene transfer events which are responsible for the genomic diversity of this group of bacteriophages and demonstrated that these changes are not consistent with the idea that modular reassortment of genomes occurs in this group of bacteriophages.

Resolution factors in edgeline holography.

PubMed

Trolinger, J D; Gee, T H

1971-06-01

When an in-line Fresnel hologram of an object such as a projectile in flight is made, the reconstruction comprises an image of the outside edge of the object superimposed upon a Fresnel diffraction pattern of the edge and an unmodulated portion of the reconstruction beam. When the reconstructed image is bandpass filtered, the only remaining significant contribution is that of a diffraction pattern which is symmetrical about an edgeline gaussian image of the object. The present paper discusses the application of this type of holography in accurately locating the edge of a large dynamic object, the position of which is not accurately known in any dimension. A theoretical and experimental analysis was performed to study the effects of motion, hologram size, film type, and practical limitations upon the attainable resolution in the reconstructed image. The bandlimiting effect of motion is used to relate the motion effected resolution limit of holography to that of photography. The study shows that an edgeline can be accurately located even at high velocity normal to the edge.

Scaling Patterns of Natural Urban Places as a Rule for Enhancing Their Urban Functionality Using Trajectory Data

NASA Astrophysics Data System (ADS)

Jia, T.; Yu, X.

2018-04-01

With the availability of massive trajectory data, it is highly valuable to reveal their activity information for many domains such as understanding the functionality of urban regions. This article utilizes the scaling patterns of human activities to enhance functional distribution of natural urban places. Specifically, we proposed a temporal city clustering algorithm to aggregate the stopping locations into natural urban places, which are reported to follow remarkable power law distributions of sizes and obey a universal law of economy of scale on human interactions with urban infrastructure. Besides, we proposed a novel Bayesian inference model with damping factor to estimate the most likely POI type associated with a stopping location. Our results suggest that hot natural urban places could be effectively identified from their scaling patterns and their functionality can be very well enhanced. For instance, natural urban places containing airport or railway station can be highly stressed by accumulating the massive types of human activities.

Aerosol seeding systems for the NSWC wind tunnels

NASA Technical Reports Server (NTRS)

Yanta, W. J.; Smith, T. S.; Collier, A. S.

1985-01-01

Four types of laskin nozzles which are used to generate the primary aerosol mist are illustrated. This mist may be used directly as laser doppler velocimeters (LDV) particles. However, in general, a wide range of particle size exists at this stage and requires the use of some type of mono-dispersion refinement technique. These nozzles rely on the shearing action of high speed air near a column of seeding liquid. Typically, olive oil or dioctyl phthalate (DOP) is used, but within the past year solid polystyrene particles in an alcohol suspension have been used with great success. Air, at a typical pressure of five psig, is supplied to the top of the nozzle which is merely a hollow tube. This air issues radially from one or more small jets located near the collar close to the bottom of the tube. When the collar is submerged in the seeding liquid, the hollow columns located in the collar become filled with liquid. The air from the jet shears the liquid into the fine mist.

Passive acoustic telemetry reveals highly variable home range and movement patterns among unicornfish within a marine reserve

NASA Astrophysics Data System (ADS)

Marshell, A.; Mills, J. S.; Rhodes, K. L.; McIlwain, J.

2011-09-01

Marine reserves are the primary management tool for Guam's reef fish fishery. While a build-up of fish biomass has occurred inside reserve boundaries, it is unknown whether reserve size matches the scale of movement of target species. Using passive acoustic telemetry, we quantified movement patterns and home range size of two heavily exploited unicornfish Naso unicornis and Naso lituratus. Fifteen fish ( N. unicornis: n = 7; N. lituratus: n = 4 male, n = 4 female) were fitted with internal acoustic tags and tracked continuously over four months within a remote acoustic receiver array located in a decade-old marine reserve. This approach provided robust estimates of unicornfish movement patterns and home range size. The mean home range of 3.2 ha for N. unicornis was almost ten times larger than that previously recorded from a three-week tracking study of the species in Hawaii. While N. lituratus were smaller in body size, their mean home range (6.8 ha) was over twice that of N. unicornis. Both species displayed strong site fidelity, particularly during nocturnal and crepuscular periods. Although there was some overlap, individual movement patterns and home range size were highly variable within species and between sexes. N. unicornis home range increased with body size, and only the three largest fish home ranges extended into the deeper outer reef slope beyond the shallow reef flat. Both Naso species favoured habitat dominated by corals. Some individuals made predictable daily crepuscular migrations between different locations or habitat types. There was no evidence of significant spillover from the marine reserve into adjacent fished areas. Strong site fidelity coupled with negligible spillover suggests that small-scale reserves, with natural habitat boundaries to emigration, are effective in protecting localized unicornfish populations.

Three-dimensional positioning of B chromosomes in fibroblast nuclei of the red fox and the chinese raccoon dog.

PubMed

Kociucka, B; Sosnowski, J; Kubiak, A; Nowak, A; Pawlak, P; Szczerbal, I

2013-01-01

Great progress has been achieved over the last years in studies on chromosome arrangement in mammalian cell nuclei. Growing evidence indicates that the genome's spatial organization is of functional relevance. So far, no attention has been paid to the nuclear organization of B chromosomes (Bs). In this study we have examined nuclear positioning of Bs in 2 species from the Canidae family--the red fox and the Chinese raccoon dog. Using 2D and 3D fluorescence in situ hybridization and 2 gene-specific probes (C-KIT and PDGFRA), we analyzed the location of Bs in fibroblast nuclei. We found that small Bs of the red fox occupied mostly the interior of the nucleus, while medium-sized Bs of the Chinese raccoon dog were observed in the peripheral area of the nucleus as well as in intermediate and interior locations. The more uniform distribution of B chromosomes in the Chinese raccoon dog may be the result of differences in their size, since 3 morphological types of Bs are distinguished in this species. Our results indicate that 3D positioning of B chromosomes in fibroblast nuclei of the 2 canid species is in agreement with the chromosome size-dependent theory. Copyright © 2013 S. Karger AG, Basel.

Feature-location binding in 3D: Feature judgments are biased by 2D location but not position-in-depth

PubMed Central

Finlayson, Nonie J.; Golomb, Julie D.

2016-01-01

A fundamental aspect of human visual perception is the ability to recognize and locate objects in the environment. Importantly, our environment is predominantly three-dimensional (3D), but while there is considerable research exploring the binding of object features and location, it is unknown how depth information interacts with features in the object binding process. A recent paradigm called the spatial congruency bias demonstrated that 2D location is fundamentally bound to object features (Golomb, Kupitz, & Thiemann, 2014), such that irrelevant location information biases judgments of object features, but irrelevant feature information does not bias judgments of location or other features. Here, using the spatial congruency bias paradigm, we asked whether depth is processed as another type of location, or more like other features. We initially found that depth cued by binocular disparity biased judgments of object color. However, this result seemed to be driven more by the disparity differences than the depth percept: Depth cued by occlusion and size did not bias color judgments, whereas vertical disparity information (with no depth percept) did bias color judgments. Our results suggest that despite the 3D nature of our visual environment, only 2D location information – not position-in-depth – seems to be automatically bound to object features, with depth information processed more similarly to other features than to 2D location. PMID:27468654

Feature-location binding in 3D: Feature judgments are biased by 2D location but not position-in-depth.

PubMed

Finlayson, Nonie J; Golomb, Julie D

2016-10-01

A fundamental aspect of human visual perception is the ability to recognize and locate objects in the environment. Importantly, our environment is predominantly three-dimensional (3D), but while there is considerable research exploring the binding of object features and location, it is unknown how depth information interacts with features in the object binding process. A recent paradigm called the spatial congruency bias demonstrated that 2D location is fundamentally bound to object features, such that irrelevant location information biases judgments of object features, but irrelevant feature information does not bias judgments of location or other features. Here, using the spatial congruency bias paradigm, we asked whether depth is processed as another type of location, or more like other features. We initially found that depth cued by binocular disparity biased judgments of object color. However, this result seemed to be driven more by the disparity differences than the depth percept: Depth cued by occlusion and size did not bias color judgments, whereas vertical disparity information (with no depth percept) did bias color judgments. Our results suggest that despite the 3D nature of our visual environment, only 2D location information - not position-in-depth - seems to be automatically bound to object features, with depth information processed more similarly to other features than to 2D location. Copyright © 2016 Elsevier Ltd. All rights reserved.

How well do the theory of reasoned action and theory of planned behaviour predict intentions and attendance at screening programmes? A meta-analysis.

PubMed

Cooke, Richard; French, David P

2008-01-01

Meta-analysis was used to quantify how well the Theories of Reasoned Action and Planned Behaviour have predicted intentions to attend screening programmes and actual attendance behaviour. Systematic literature searches identified 33 studies that were included in the review. Across the studies as a whole, attitudes had a large-sized relationship with intention, while subjective norms and perceived behavioural control (PBC) possessed medium-sized relationships with intention. Intention had a medium-sized relationship with attendance, whereas the PBC-attendance relationship was small sized. Due to heterogeneity in results between studies, moderator analyses were conducted. The moderator variables were (a) type of screening test, (b) location of recruitment, (c) screening cost and (d) invitation to screen. All moderators affected theory of planned behaviour relationships. Suggestions for future research emerging from these results include targeting attitudes to promote intention to screen, a greater use of implementation intentions in screening information and examining the credibility of different screening providers.

Final Results of Shuttle MMOD Impact Database

NASA Technical Reports Server (NTRS)

Hyde, J. L.; Christiansen, E. L.; Lear, D. M.

2015-01-01

The Shuttle Hypervelocity Impact Database documents damage features on each Orbiter thought to be from micrometeoroids (MM) or orbital debris (OD). Data is divided into tables for crew module windows, payload bay door radiators and thermal protection systems along with other miscellaneous regions. The combined number of records in the database is nearly 3000. Each database record provides impact feature dimensions, location on the vehicle and relevant mission information. Additional detail on the type and size of particle that produced the damage site is provided when sampling data and definitive spectroscopic analysis results are available. Guidelines are described which were used in determining whether impact damage is from micrometeoroid or orbital debris impact based on the findings from scanning electron microscopy chemical analysis. Relationships assumed when converting from observed feature sizes in different shuttle materials to particle sizes will be presented. A small number of significant impacts on the windows, radiators and wing leading edge will be highlighted and discussed in detail, including the hypervelocity impact testing performed to estimate particle sizes that produced the damage.

Gustaf: Detecting and correctly classifying SVs in the NGS twilight zone.

PubMed

Trappe, Kathrin; Emde, Anne-Katrin; Ehrlich, Hans-Christian; Reinert, Knut

2014-12-15

The landscape of structural variation (SV) including complex duplication and translocation patterns is far from resolved. SV detection tools usually exhibit low agreement, are often geared toward certain types or size ranges of variation and struggle to correctly classify the type and exact size of SVs. We present Gustaf (Generic mUlti-SpliT Alignment Finder), a sound generic multi-split SV detection tool that detects and classifies deletions, inversions, dispersed duplications and translocations of ≥ 30 bp. Our approach is based on a generic multi-split alignment strategy that can identify SV breakpoints with base pair resolution. We show that Gustaf correctly identifies SVs, especially in the range from 30 to 100 bp, which we call the next-generation sequencing (NGS) twilight zone of SVs, as well as larger SVs >500 bp. Gustaf performs better than similar tools in our benchmark and is furthermore able to correctly identify size and location of dispersed duplications and translocations, which otherwise might be wrongly classified, for example, as large deletions. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Correlates of in-store promotions for beer: differential effects of market and product characteristics.

PubMed

Bray, Jeremy W; Loomis, Brett; Engelen, Mark

2007-03-01

We estimated the strength and direction of the association between product characteristics (beer type, package size, and brand name) and market-area socioeconomic characteristics, and promoted sales of beer in grocery stores. Supermarket scanner data from 64 market areas across the United States over 5 years were used to estimate regression models of the share of beer sales that are promoted, controlling for beer price, packaging, and type; and for market-level age, race/ethnicity, income, unemployment rate, and percentage of the population living in an alcohol control state. Large-volume units, such as 144-oz and 288-oz packages, are more likely to be promoted than smaller package sizes. Malt-liquor beverages are less likely to be promoted than non-malt-liquor beverages. Age, race/ethnicity, income, and geographic location of the market area are not significantly related to promoted beer sales. Marketing research has shown that in-store merchandising and promotions can substantially increase beer sales and that purchasing large package sizes may increase total consumption. Our results suggest that high levels of promoted sales for large-volume beer packages may result in increased beer consumption.

A dataset of housing market and self-attitudes towards housing location choices in Alexandria, Egypt.

PubMed

Ibrahim, Mohamed R

2017-04-01

A survey, of sample size 224, is designed to include the different related-factors to housing location choice, such as; socioeconomic factors, housing characteristics, travel behavior, current self-selection factors, housing demand and future location preferences. It comprises 16 questions, categorized into three different sections; socioeconomic (5 Questions), current dwelling unit characteristics (7 Questions), and housing demand characteristics (4 Questions). The first part, socioeconomic, covers the basic information about the respondent, such as; age, gender, marital status, employment, and car ownership. While the second part, current dwelling unit characteristics, covers different aspect concerning the residential unit typology, financial aspects, and travel behavior of the respondent. It includes the tenure types of the residential unit, estimation of the unit price (in the case of ownership or renting), housing typologies, the main reason for choosing the unit, in case of working, the modes of travel to work, and time to reach it, residential mobility in the last decade, and the ownership of any other residential units. The last part, housing demand characteristics, covers the size of the demand for a residential unit, preference in living in a certain area and the reason to choose it, and the preference of residential unit׳s tenure. This survey is a representative sample for the population in Alexandria, Egypt. The data in this article is represented in: How do people select their residential locations in Egypt? The case of Alexandria; JCIT1757.

Investigating motivating factors for sound hospital waste management.

PubMed

Ali, Mustafa; Wang, Wenping; Chaudhry, Nawaz

2016-08-01

Sustainable management of hospital waste requires an active involvement of all key players. This study aims to test the hypothesis that three motivating factors, namely, Reputation, Liability, and Expense, influence hospital waste management. The survey for this study was conducted in two phases, with the pilot study used for exploratory factor analysis and the subsequent main survey used for cross-validation using confirmatory factor analysis. The hypotheses were validated through one-sample t tests. Correlations were established between the three motivating factors and organizational characteristics of hospital type, location, category, and size. The hypotheses were validated, and it was found that the factors of Liability and Expense varied considerably with respect to location and size of a hospital. The factor of Reputation, however, did not exhibit significant variation. In conclusion, concerns about the reputation of a facility and an apprehension of liability act as incentives for sound hospital waste management, whereas concerns about financial costs and perceived overburden on staff act as disincentives. This paper identifies the non economic motivating factors that can be used to encourage behavioral changes regarding waste management at hospitals in resource constrained environments. This study discovered that organizational characteristics such as hospital size and location cause the responses to vary among the subjects. Hence a policy maker must take into account the institutional setting before introducing a change geared towards better waste management outcomes across hospitals. This study covers a topic that has hitherto been neglected in resource constrained countries. Thus it can be used as one of the first steps to highlight and tackle the issue.

Community structure of fish larvae in mangroves with different root types in Labuhan coastal area, Sepulu - Madura

NASA Astrophysics Data System (ADS)

Muzaki, Farid Kamal; Giffari, Aninditha; Saptarini, Dian

2017-06-01

Mangrove root complexity and shading are well known to give positive correlation for both juveniles and adult fishes. However, it is remain unclear whether that complexity would affect the community of fish larvae (ichthyoplankton). This study aimed to address the question, especially in mangrove area in coastal area of Sepulu, Madura which projected as a mangrove protection area. Sampling periods were from March to May, 2016. The samples of fish larvae were collected by plankton net (mesh-size 0.150 and 0.265 mm) from six different locations representing different root types (stilt root, pneumatophore, combination of stilt root-pneumatophore and unvegetated area). As the results, 6 families were identified, namely Gobiidae, Blennidae, Pomacentridae, Carangidae, Engraulidae and Ambassidae, respectively. Gobiidae seems to be the most abundant and widely dispersed in the area. Results of two-way AnovadanTukey HSD (both at p=0.05) indicate that there were significant difference in the larval abundance regarding locations, sampling periods and interaction of both factors. As for number of taxa, significant difference occurred only from factors of locations and sampling periods, but not for interaction of both factors. Highest larval abundance and number of taxa occurred in Rhizophoraspp (with stilt root), indicating that root complexity would affect the community of fish larvae. Ordination by canonical analysis shows that different taxa of the fish larvae are tend to be distributed on different locations.

Pollen Morphology of Caesalpinia pulcherrima (L.) Swartz in Highland and Lowland West Sumatra

NASA Astrophysics Data System (ADS)

Fitri, R.; Des, M.

2018-04-01

Determine the morphology structure of pollen on some variation colour of corolla Caesalpinia pulcherrima L. (Swartz) in highland and lowland West Sumatra has been conducted. The result reveals that topography and variation colour of corolla C. pulcherrima L. (Swartz) affects the shape of pollen. Pollen of C. pulcherrima L. (Swartz) has single grains or monad, isopolar polarity, radial symmetry, and size categories large. The length of polar axis (P) 58.16 to 74.11 μm, the length of the equatorial diameter (E) 59.86 to 75.97 μm, so that pollen can be classified into sub-spheroidal sub-oblate, spheriodal sub-spheroidal oblate, and sub-spheroidal prolate. Ornamentation of C. pulcherrima (L.) Swartz was reticulate. The pollen has aperture 3, the type pore and located in equatorial. From these data can be concluded that pollen from varying colour of corolla C. pulcherrima (L.) Swartz has same in terms of unit, polarity, symmetry, size, and type aperture, but it different in terms of shape.

Audiomagnetotelluric data to characterize the Revett-type copper-silver deposits at Rock Creek in the Cabinet Mountains Wilderness, Montana

USGS Publications Warehouse

Sampson, Jay A.; Rodriguez, Brian D.

2011-01-01

The Revett-type deposits at Rock Creek are part of the concealed stratabound copper-silver deposits located in the Cabinet Mountains Wilderness of Montana. The U.S. Geological Survey is conducting a series of multidisciplinary studies as part of the Assessment Techniques for Concealed Mineral Resources project. Geologic, geochemical, geophysical, and mineral resources data are being evaluated with existing and new mineral deposit models to predict the possibility and probability of undiscovered deposits in covered terranes. To help characterize the size, resistivity, and depth of the mineral deposit concealed beneath thick overburden, a regional southwest-northeast audiomagnetotelluric sounding profile was acquired. Further studies will attempt to determine if induced polarization parameters can be extracted from the magnetotelluric data to determine the size of the mineralized area. The purpose of this report is to release the audiomagnetotelluric sounding data collected along that southwest-northeast profile. No interpretation of the data is included.

Explicit Cloud Nucleation from Arbitrary Mixtures of Aerosol Types and Sizes Using an Ultra-Efficient In-Line Aerosol Bin Model in High-Resolution Simulations of Hurricanes

NASA Astrophysics Data System (ADS)

Walko, R. L.; Ashby, T.; Cotton, W. R.

2017-12-01

The fundamental role of atmospheric aerosols in the process of cloud droplet nucleation is well known, and there is ample evidence that the concentration, size, and chemistry of aerosols can strongly influence microphysical, thermodynamic, and ultimately dynamic properties and evolution of clouds and convective systems. With the increasing availability of observation- and model-based environmental representations of different types of anthropogenic and natural aerosols, there is increasing need for models to be able to represent which aerosols nucleate and which do not in supersaturated conditions. However, this is a very complex process that involves competition for water vapor between multiple aerosol species (chemistries) and different aerosol sizes within each species. Attempts have been made to parameterize the nucleation properties of mixtures of different aerosol species, but it is very difficult or impossible to represent all possible mixtures that may occur in practice. As part of a modeling study of the impact of anthropogenic and natural aerosols on hurricanes, we developed an ultra-efficient aerosol bin model to represent nucleation in a high-resolution atmospheric model that explicitly represents cloud- and subcloud-scale vertical motion. The bin model is activated at any time and location in a simulation where supersaturation occurs and is potentially capable of activating new cloud droplets. The bins are populated from the aerosol species that are present at the given time and location and by multiple sizes from each aerosol species according to a characteristic size distribution, and the chemistry of each species is represented by its absorption or adsorption characteristics. The bin model is integrated in time increments that are smaller than that of the atmospheric model in order to temporally resolve the peak supersaturation, which determines the total nucleated number. Even though on the order of 100 bins are typically utilized, this leads only to a 10 or 20% increase in overall computational cost due to the efficiency of the bin model. This method is highly versatile in that it automatically accommodates any possible number and mixture of different aerosol species. Applications of this model to simulations of Typhoon Nuri will be presented.

Identification of small-scale low and high permeability layers using single well forced-gradient tracer tests: fluorescent dye imaging and modelling at the laboratory-scale.

PubMed

Barns, Gareth L; Thornton, Steven F; Wilson, Ryan D

2015-01-01

Heterogeneity in aquifer permeability, which creates paths of varying mass flux and spatially complex contaminant plumes, can complicate the interpretation of contaminant fate and transport in groundwater. Identifying the location of high mass flux paths is critical for the reliable estimation of solute transport parameters and design of groundwater remediation schemes. Dipole flow tracer tests (DFTTs) and push-pull tests (PPTs) are single well forced-gradient tests which have been used at field-scale to estimate aquifer hydraulic and transport properties. In this study, the potential for PPTs and DFTTs to resolve the location of layered high- and low-permeability layers in granular porous media was investigated with a pseudo 2-D bench-scale aquifer model. Finite element fate and transport modelling was also undertaken to identify appropriate set-ups for in situ tests to determine the type, magnitude, location and extent of such layered permeability contrasts at the field-scale. The characteristics of flow patterns created during experiments were evaluated using fluorescent dye imaging and compared with the breakthrough behaviour of an inorganic conservative tracer. The experimental results show that tracer breakthrough during PPTs is not sensitive to minor permeability contrasts for conditions where there is no hydraulic gradient. In contrast, DFTTs are sensitive to the type and location of permeability contrasts in the host media and could potentially be used to establish the presence and location of high or low mass flux paths. Numerical modelling shows that the tracer peak breakthrough time and concentration in a DFTT is sensitive to the magnitude of the permeability contrast (defined as the permeability of the layer over the permeability of the bulk media) between values of 0.01-20. DFTTs are shown to be more sensitive to deducing variations in the contrast, location and size of aquifer layered permeability contrasts when a shorter central packer is used. However, larger packer sizes are more likely to be practical for field-scale applications, with fewer tests required to characterise a given aquifer section. The sensitivity of DFTTs to identify layered permeability contrasts was not affected by test flow rate. Copyright © 2014 Elsevier B.V. All rights reserved.

Detailed study of scratch drive actuator characteristics using high-speed imaging

NASA Astrophysics Data System (ADS)

Li, Lijie; Brown, James G.; Uttamchandani, Deepak G.

2001-10-01

Microactuators are one of the key components in MEMS and Microsystems technology, and various designs have been realized through different fabrication processes. One type of microactuator commonly used is the scratch drive actuator (SDA) that is frequently fabricated by surface micromachining processes. An experimental investigation has been conducted on the characteristics of SDAs fabricated using the Cronos Microsystems MUMPs process. The motivation is to compare the response of SDAs located on the same die, and SDAs located on the different dies from the same fabrication batch. A high-speed imaging camera has been used to precisely determine important SDA characteristics such as step size, velocity, maximum velocity, and acceleration over long travel distance. These measurements are important from a repeatability point of view, and in order to fully exploit the potential of the SDA as a precise positioning mechanism. 2- and 3-stage SDAs have been designed and fabricated for these experiments. Typical step sizes varying from 7 nm at a driving voltage of 60 V to 23 nm at 290 V have been obtained.

Bilateral chorioretinal coloboma discovered with ultra-wide field retinal imaging

PubMed Central

Barnard, Simon; Shneor, Einat; Brauner, Joel; Millodot, Michel; Gordon-Shaag, Ariela

2012-01-01

Uveal coloboma results from incomplete closure of the optic cup fissure. While conducting an evaluation of a new ultra-wide field retinal imaging camera (Optomap), which provides a view of the fundus up to 200° at one time without mydriasis, we discovered a case of bilateral chorioretinal coloboma in a 21-year-old student. The lesion was located in the midperiphery of each eye less than 2 disc diameters (DD) below the optic disc in the inferonasal quadrants. The size of the coloboma in the right eye was 1.8 DD in height and 1.3 DD in width, while the left lesion was 2.4 DD in height and 2.6 DD in width. The subject was totally asymptomatic and without any complication such as retinal detachment or choroidal neovascularization, which often accompany this type of lesion. The visual field of each eye displayed an absolute scotoma corresponding to the size and location of the coloboma. No management was necessary but the subject was advised to report for visual examination at regular intervals because complications can occur at any age.

Endogenous Life Cycle of Eimeria marmosopos (Apicomplexa: Eimeriidae) from the Opossum, Didelphis marsupialis (Didelphimorphia: Didelphidae) in Costa Rica.

PubMed

Chinchilla, Misael; Valerio, Idalia; Duszynski, Donald

2015-08-01

The endogenous life cycle of Eimeria marmosopos was studied in experimentally infected young opossums, Didelphis marsupialis . All the endogenous stages were located in the epithelial cells of villi in the small intestine. Giemsa-stained mucosal scrapings and histological sections were studied for the diagnosis of all the life cycle stages. Eimeria marmosopos has 3 generations of meronts (M) that differ by size, shape, and number of merozoites (m), which also differ in their size, shape, and location of their nuclei within the cytoplasm of the meronts. The 3 meront types, M(1)-M(3), respectively, had 8-15 (m(1)), 4-9 (m(2)), and 22-30 (m(3)) merozoites. Macrogametocytes and microgametocytes, as well as macrogametes and microgametes, completed the sexual cycle, finishing with the formation of unsporulated oocysts. This parasite's endogenous development produced severe intestinal lesions in experimentally infected opossums. There are 56 Eimeria species known from all marsupials worldwide, but this is the first complete life cycle in which both the asexual and sexual stages have been documented.

Birth weight, birth type and pre-weaning survivability of West African Dwarf goats raised in the Dangme West District of the Greater Accra Region of Ghana.

PubMed

Baiden, R Y

2007-02-01

A study was conducted on 441 West African Dwarf goat (WADG) kids born from September 1999 to August 2002 at three locations in the Dangme West District of the Greater Accra Region in Ghana to determine the effect of environmental factors on birth weight, birth type and pre-weaning survivability. The overall mean birth weight was 1.32 +/- 0.01 kg. Birth weights were similar (p > 0.05) between single births (1.43 +/- 0.04 kg) and twins (1.34 +/- 0.03 kg), but singles were significantly heavier (p < 0.05) than triplets (1.24 +/- 0.05 kg). Kids born in the major wet season recorded the best mean birth weight (1.37 +/- 0.04 kg). Sex, parity of does, and year of birth of kids had no significant (p > 0.05) effect on birth weight. Mean litter size was 1.93 +/- 0.03. Does that kidded in the dry season had a significantly (p < 0.05) higher litter size (2.05 +/- 0.06) than those that kidded in the minor wet season (1.80 +/- 0.10). Litter size of first-parity kids was significantly smaller (p < 0.05) than in subsequent parities. Litter size dropped significantly (p < 0.05) from year 2 (2.03 +/- 0.07) to year 3 (1.83 +/- 0.07). Pre-weaning survivability was 79.1% and season of kidding had a significant (p < 0.05) effect on survivability. Survivability of quadruplets (61.8%) was significantly (p < 0.05) lower than in the other birth types.

Analytical and Experimental Investigations of Delta Wings in Incompressible Flow

DTIC Science & Technology

1976-08-01

posi- tion unless so designated by other official documents. Rep roduct ion Reproduction in whole or in part is permitted for any purpose of the...Trailing Edge of Free-Wake Model 56 19 Polar Coordinate System 5i 20 Free-Wake Geometry Prediction 5 21 Finite-Size Core 58 22 Vortex Core Position of Smith...k=0.4 70 34 Details of a Helical Type Burst 71 35 Vortex Burst-Steady Flow 72 36 Location of Pressure Ports 73 37 Pressure Destribution on a Delta

WIAMan Technology Demonstrator Sensor Codes Conforming to International Organization for Standardization/Technical Standard (ISO/TS) 13499

DTIC Science & Technology

2016-03-01

in this report are not to be construed as an official Department of the Army position unless so designated by other authorized documents. Citation of...gravity, or pretest . 1 Approved for public release; distribution is unlimited. Fine Location 2 Code position 9–10: This substring represents the spacial...itself. For example, upper, pretest , or Hybrid III mid-sized male ATD. Physical dimension Code position 13–14: This substring represents the type of the

Development of Facility Type Information Packages for Design of Air Force Facilities.

DTIC Science & Technology

1983-03-01

solution. For example, the optimum size and loca- 19 tion of windows for the incorporation of a passive solar *l . heating system varies with location, time...conditioning load estimate M. Energy impact statement N. Majcom review comments 0. Solar energy systems 61 4 Information which could help in the development...and Passive solar systems. All facilities should have Scme aspects of passive solar incor- por3ted into the iesign. Active sclar systems should ze con

46 CFR 108.233 - Location and size.

Code of Federal Regulations, 2012 CFR

2012-10-01

... EQUIPMENT Construction and Arrangement Helicopter Facilities § 108.233 Location and size. (a) Each helicopter deck must be— (1) At least the size of the rotor diameter of the largest single main rotor helicopter that will be used on the facility; or (2) If tandem main rotor helicopters use the facility, at...

46 CFR 108.233 - Location and size.

Code of Federal Regulations, 2011 CFR

2011-10-01

... EQUIPMENT Construction and Arrangement Helicopter Facilities § 108.233 Location and size. (a) Each helicopter deck must be— (1) At least the size of the rotor diameter of the largest single main rotor helicopter that will be used on the facility; or (2) If tandem main rotor helicopters use the facility, at...

46 CFR 108.233 - Location and size.

Code of Federal Regulations, 2014 CFR

2014-10-01

... EQUIPMENT Construction and Arrangement Helicopter Facilities § 108.233 Location and size. (a) Each helicopter deck must be— (1) At least the size of the rotor diameter of the largest single main rotor helicopter that will be used on the facility; or (2) If tandem main rotor helicopters use the facility, at...

46 CFR 108.233 - Location and size.

Code of Federal Regulations, 2010 CFR

2010-10-01

... EQUIPMENT Construction and Arrangement Helicopter Facilities § 108.233 Location and size. (a) Each helicopter deck must be— (1) At least the size of the rotor diameter of the largest single main rotor helicopter that will be used on the facility; or (2) If tandem main rotor helicopters use the facility, at...

46 CFR 108.233 - Location and size.

Code of Federal Regulations, 2013 CFR

2013-10-01

... EQUIPMENT Construction and Arrangement Helicopter Facilities § 108.233 Location and size. (a) Each helicopter deck must be— (1) At least the size of the rotor diameter of the largest single main rotor helicopter that will be used on the facility; or (2) If tandem main rotor helicopters use the facility, at...

AGN Luminosity and Stellar Age: Two Missing Ingredients for AGN Unification as Seen with iPTF Supernovae

NASA Astrophysics Data System (ADS)

Villarroel, Beatriz; Nyholm, Anders; Karlsson, Torgny; Comerón, Sébastien; Korn, Andreas J.; Sollerman, Jesper; Zackrisson, Erik

2017-03-01

Active galactic nuclei (AGNs) are extremely powerful cosmic objects, driven by accretion of hot gas upon super-massive black holes. The zoo of AGN classes is divided into two major groups, with Type-1 AGNs displaying broad Balmer emission lines and Type-2 narrow ones. For a long time it was believed that a Type-2 AGN is a Type-1 AGN viewed through a dusty kiloparsec-sized torus, but an emerging body of observations suggests more than just the viewing angle matters. Here we report significant differences in supernova (SN) counts and classes in the first study to date of SNe near Type-1 and Type-2 AGN host galaxies, using data from the intermediate Palomar Transient Factory, the Sloan Digital Sky Survey Data Release 7, and Galaxy Zoo. We detect many more SNe in Type-2 AGN hosts (size of effect ˜5.1σ) compared to Type-1 hosts, which shows that the two classes of AGN are located inside host galaxies with different properties. In addition, Type-1 and Type-2 AGNs that are dominated by star formation according to Wide-field Infrared Survey Explorer colors {m}W1-{m}W2< 0.5 and are matched in 22 μm absolute magnitude differ by a factor of ten in L[O III] λ5007 luminosity, suggesting that when residing in similar types of host galaxies Type-1 AGNs are much more luminous. Our results demonstrate two more factors that play an important role in completing the current picture: the age of stellar populations and the AGN luminosity. This has immediate consequences for understanding the many AGN classes and galaxy evolution.

A mathematical model of single target site location by Brownian movement in subcellular compartments.

PubMed

Kuthan, Hartmut

2003-03-07

The location of distinct sites is mandatory for many cellular processes. In the subcompartments of the cell nucleus, only very small numbers of diffusing macromolecules and specific target sites of some types may be present. In this case, we are faced with the Brownian movement of individual macromolecules and their "random search" for single/few specific target sites, rather than bulk-averaged diffusion and multiple sites. In this article, I consider the location of a distant central target site, e.g. a globular protein, by individual macromolecules executing unbiased (i.e. drift-free) random walks in a spherical compartment. For this walk-and-capture model, the closed-form analytic solution of the first passage time probability density function (p.d.f.) has been obtained as well as the first and second moment. In the limit of a large ratio of the radii of the spherical diffusion space and central target, well-known relations for the variance and the first two moments for the exponential p.d.f. were found to hold with high accuracy. These calculations reinforce earlier numerical results and Monte Carlo simulations. A major implication derivable from the model is that non-directed random movement is an effective means for locating single sites in submicron-sized compartments, even when the diffusion coefficients are comparatively small and the diffusing species are present in one copy only. These theoretical conclusions are underscored numerically for effective diffusion constants ranging from 0.5 to 10.0 microm(2) s(-1), which have been reported for a couple of nuclear proteins in their physiological environment. Spherical compartments of submicron size are, for example, the Cajal bodies (size: 0.1-1.0 microm), which are present in 1-5 copies in the cell nucleus. Within a small Cajal body of radius 0.1 microm a single diffusing protein molecule (with D=0.5 microm(2) s(-1)) would encounter a medium-sized protein of radius 2.5 nm within 1 s with a probability near certainty (p=0.98).

Anatomy and Classification of Gastrorenal and Gastrocaval Shunts

PubMed Central

Sabri, Saher S.; Saad, Wael E. A.

2011-01-01

The gastric varices communicate with gastrorenal and gastrocaval shunts and are classified according to the pattern of venous inflow into three types, which differ in the number and location of the inflow veins. The gastric varices are also classified according to their venous drainage into four different types, reflecting the size and number of collateral veins communicating with the gastric varices and the gastrorenal/gastrocaval shunt. Lastly, the gastric varices are classified according to their appearance on balloon-occluded retrograde venography into five grades representing the degree of opacification of the gastric varices and the collateral veins. Understanding these anatomic classifications is crucial in planning endovascular obliteration of gastric varices. PMID:22942547

Compilation of gallium resource data for bauxite deposits

USGS Publications Warehouse

Schulte, Ruth F.; Foley, Nora K.

2014-01-01

Gallium (Ga) concentrations for bauxite deposits worldwide have been compiled from the literature to provide a basis for research regarding the occurrence and distribution of Ga worldwide, as well as between types of bauxite deposits. In addition, this report is an attempt to bring together reported Ga concentration data into one database to supplement ongoing U.S. Geological Survey studies of critical mineral resources. The compilation of Ga data consists of location, deposit size, bauxite type and host rock, development status, major oxide data, trace element (Ga) data and analytical method(s) used to derive the data, and tonnage values for deposits within bauxite provinces and districts worldwide. The range in Ga concentrations for bauxite deposits worldwide is

DIORAMA Location Type User's Guide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Terry, James Russell

2015-01-29

The purpose of this report is to present the current design and implementation of the DIORAMA location type object (LocationType) and to provide examples and use cases. The LocationType object is included in the diorama-app package in the diorama::types namespace. Abstractly, the object is intended to capture the full time history of the location of an object or reference point. For example, a location may be speci ed as a near-Earth orbit in terms of a two-line element set, in which case the location type is capable of propagating the orbit both forward and backward in time to provide amore » location for any given time. Alternatively, the location may be speci ed as a xed set of geodetic coordinates (latitude, longitude, and altitude), in which case the geodetic location of the object is expected to remain constant for all time. From an implementation perspective, the location type is de ned as a union of multiple independent objects defi ned in the DIORAMA tle library. Types presently included in the union are listed and described in subsections below, and all conversions or transformation between these location types are handled by utilities provided by the tle library with the exception of the \\special-values" location type.« less

Conspicuity of renal calculi at unenhanced CT: effects of calculus composition and size and CT technique.

PubMed

Tublin, Mitchell E; Murphy, Michael E; Delong, David M; Tessler, Franklin N; Kliewer, Mark A

2002-10-01

To determine the effects of calculus size, composition, and technique (kilovolt and milliampere settings) on the conspicuity of renal calculi at unenhanced helical computed tomography (CT). The authors performed unenhanced CT of a phantom containing 188 renal calculi of varying size and chemical composition (brushite, cystine, struvite, weddellite, whewellite, and uric acid) at 24 combinations of four kilovolt (80-140 kV) and six milliampere (200-300 mA) levels. Two radiologists, who were unaware of the location and number of calculi, reviewed the CT images and recorded where stones were detected. These observations were compared with the known positions of calculi to generate true-positive and false-positive rates. Logistic regression analysis was performed to investigate the effects of stone size, composition, and technique and to generate probability estimates of detection. Interobserver agreement was estimated with kappa statistics. Interobserver agreement was high: the mean kappa value for the two observers was 0.86. The conspicuity of stone fragments increased with increasing kilovolt and milliampere levels for all stone types. At the highest settings (140 kV and 300 mA), the detection threshold size (ie, the size of calculus that had a 50% probability of being detected) ranged from 0.81 mm + 0.03 (weddellite) to 1.3 mm + 0.1 (uric acid). Detection threshold size for each type of calculus increased up to 1.17-fold at lower kilovolt settings and up to 1.08-fold at lower milliampere settings. The conspicuity of small renal calculi at CT increases with higher kilovolt and milliampere settings, with higher kilovolts being particularly important. Small uric acid calculi may be imperceptible, even with maximal CT technique.

Interactions between target location and reward size modulate the rate of microsaccades in monkeys

PubMed Central

Tokiyama, Stefanie; Lisberger, Stephen G.

2015-01-01

We have studied how rewards modulate the occurrence of microsaccades by manipulating the size of an expected reward and the location of the cue that sets the expectations for future reward. We found an interaction between the size of the reward and the location of the cue. When monkeys fixated on a cue that signaled the size of future reward, the frequency of microsaccades was higher if the monkey expected a large vs. a small reward. When the cue was presented at a site in the visual field that was remote from the position of fixation, reward size had the opposite effect: the frequency of microsaccades was lower when the monkey was expecting a large reward. The strength of pursuit initiation also was affected by reward size and by the presence of microsaccades just before the onset of target motion. The gain of pursuit initiation increased with reward size and decreased when microsaccades occurred just before or after the onset of target motion. The effect of the reward size on pursuit initiation was much larger than any indirect effects reward might cause through modulation of the rate of microsaccades. We found only a weak relationship between microsaccade direction and the location of the exogenous cue relative to fixation position, even in experiments where the location of the cue indicated the direction of target motion. Our results indicate that the expectation of reward is a powerful modulator of the occurrence of microsaccades, perhaps through attentional mechanisms. PMID:26311180

Mean Glenoid Defect Size and Location Associated With Anterior Shoulder Instability

PubMed Central

Gottschalk, Lionel J.; Bois, Aaron J.; Shelby, Marcus A.; Miniaci, Anthony; Jones, Morgan H.

2017-01-01

Background: There is a strong correlation between glenoid defect size and recurrent anterior shoulder instability. A better understanding of glenoid defects could lead to improved treatments and outcomes. Purpose: To (1) determine the rate of reporting numeric measurements for glenoid defect size, (2) determine the consistency of glenoid defect size and location reported within the literature, (3) define the typical size and location of glenoid defects, and (4) determine whether a correlation exists between defect size and treatment outcome. Study Design: Systematic review; Level of evidence, 4. Methods: PubMed, Ovid, and Cochrane databases were searched for clinical studies measuring glenoid defect size or location. We excluded studies with defect size requirements or pathology other than anterior instability and studies that included patients with known prior surgery. Our search produced 83 studies; 38 studies provided numeric measurements for glenoid defect size and 2 for defect location. Results: From 1981 to 2000, a total of 5.6% (1 of 18) of the studies reported numeric measurements for glenoid defect size; from 2001 to 2014, the rate of reporting glenoid defects increased to 58.7% (37 of 63). Fourteen studies (n = 1363 shoulders) reported defect size ranges for percentage loss of glenoid width, and 9 studies (n = 570 shoulders) reported defect size ranges for percentage loss of glenoid surface area. According to 2 studies, the mean glenoid defect orientation was pointing toward the 3:01 and 3:20 positions on the glenoid clock face. Conclusion: Since 2001, the rate of reporting numeric measurements for glenoid defect size was only 58.7%. Among studies reporting the percentage loss of glenoid width, 23.6% of shoulders had a defect between 10% and 25%, and among studies reporting the percentage loss of glenoid surface area, 44.7% of shoulders had a defect between 5% and 20%. There is significant variability in the way glenoid bone loss is measured, calculated, and reported. PMID:28203591

Mucoceles of minor salivary glands in children. Own clinical observations.

PubMed

Lewandowski, Bogumił; Brodowski, Robert; Pakla, Paweł; Makara, Aleksander; Stopyra, Wojciech; Startek, Bartek

Mucoceles are benign lesions associated with the pathology of the oral mucosa of minor salivary glands. Two types of cysts are distinguished depending on their pathogenesis. Most often they occur as a result of mechanical trauma and mucus extravasation into tissues or obstruction of the gland ducts. The aim of the study was to present our own experiences regarding mucoceles of minor salivary glands in the oral cavity taking into account how frequently the individual types of cysts occur in children. The research was carried out based on medical files from the years 2005-2015. These were: medical case records, operating books and the medical registry of patients treated at the Clinic of Maxillofacial Surgery, Frederic Chopin Clinical Regional Hospital in Rzeszow. In that period 64 children and teenagers, 28 girls and 36 boys were treated. What was considered was the age and gender of the patients, the reason for their appointment with a doctor, the location, size and histopathological type of the cysts, as well as the course and results of the diagnostic and therapeutic process. In the group analyzed, the reasons for referral to the Clinic were: in 25 patients accidental ascertainment of a non-symptomatic tumor in the oral cavity during examination by a dentist, pediatrician or laryngologist which had not caused any discomfort to the children; in 13 patients concern had been raised by a gradually increasing tumor; in 18 cases there was an increased tissue tension surrounding the tumor, while in 3 children red oedema was observed in the oral cavity (suspicion of abscess). The most frequent mucocele location was the lower lip (34 children). The most frequent size was 2.1-3 cm (28 children). The most frequent histological type was MEP. All the patients were treated at the Clinic in the one-day surgery mode, with good outcome. Mucocele ascertainment in children's oral cavity could be made accidentally in routine pediatric examination, therefore it is necessary to extend pediatricians' knowledge about small salivary gland mucoceles. The most frequent type of MEP could be related to different types of trauma in the oral mucose.

Time-reversal optical tomography: detecting and locating extended targets in a turbid medium

NASA Astrophysics Data System (ADS)

Wu, Binlin; Cai, W.; Xu, M.; Gayen, S. K.

2012-03-01

Time Reversal Optical Tomography (TROT) is developed to locate extended target(s) in a highly scattering turbid medium, and estimate their optical strength and size. The approach uses Diffusion Approximation of Radiative Transfer Equation for light propagation along with Time Reversal (TR) Multiple Signal Classification (MUSIC) scheme for signal and noise subspaces for assessment of target location. A MUSIC pseudo spectrum is calculated using the eigenvectors of the TR matrix T, whose poles provide target locations. Based on the pseudo spectrum contours, retrieval of target size is modeled as an optimization problem, using a "local contour" method. The eigenvalues of T are related to optical strengths of targets. The efficacy of TROT to obtain location, size, and optical strength of one absorptive target, one scattering target, and two absorptive targets, all for different noise levels was tested using simulated data. Target locations were always accurately determined. Error in optical strength estimates was small even at 20% noise level. Target size and shape were more sensitive to noise. Results from simulated data demonstrate high potential for application of TROT in practical biomedical imaging applications.

Patients' age, myoma size, myoma location, and interval between myomectomy and pregnancy may influence the pregnancy rate and live birth rate after myomectomy.

PubMed

Zhang, Ying; Hua, Ke Qin

2014-02-01

To investigate which clinical characteristics will influence the pregnancy rate and live birth rate after myomectomy. Data of clinical characteristics and reproductive outcome from 471 patients who wished to conceive and who underwent abdominal or laparoscopic myomectomy in the Obstetrics and Gynecology Hospital of Fudan University from January 2008 to June 2012 were retrospectively analyzed. Average age in the pregnancy group (30.0±3.7 years) and the nonpregnancy group (31.2±4.1 years) was statistically different (P=.000). The diameter of the biggest myoma had a positive relationship with the pregnancy rate when it was <10 cm (rs=0.095, P=.039). Abortions before myomectomy, operation type, number, location, and classification of myomas, uterine cavity penetration, and uterine volume seemed not to influence the pregnancy rate (P>.05). The location of the myoma may influence the live birth rate after myomectomy (rs=0.198, P=.002). Anterior and posterior myomas were associated with higher live birth rates than other locations (P=.001). The average interval between myomectomy and pregnancy was 16.0±8.7 months, and there was no difference between the abdominal (17.2±8.6 months) and laparoscopic (15.2±8.8 months) groups (P=.102). The interval in the live birth group was 15.0±8.4 months, and that in the non-live birth group was 18.9±9.3 months; the difference was significant (P=.005). Patients' age, myoma size and location, and interval between myomectomy and pregnancy may influence the pregnancy rate and live birth rate after myomectomy.

How Size and Setting Impact Education in Rural Schools

ERIC Educational Resources Information Center

Bouck, Emily C.

2004-01-01

School variables, such as school size and school location, matter. School size and location impact many areas of education, including the characteristics of the school, curriculum, and post-school outcomes. Research reveals that students in rural schools face many personal and education hardships--from living in poverty to having less opportunity…

The spatial and metabolic basis of colony size variation.

PubMed

Chacón, Jeremy M; Möbius, Wolfram; Harcombe, William R

2018-03-01

Spatial structure impacts microbial growth and interactions, with ecological and evolutionary consequences. It is therefore important to quantitatively understand how spatial proximity affects interactions in different environments. We tested how proximity influences colony size when either Escherichia coli or Salmonella enterica are grown on various carbon sources. The importance of colony location changed with species and carbon source. Spatially explicit, genome-scale metabolic modeling recapitulated observed colony size variation. Competitors that determine territory size, according to Voronoi diagrams, were the most important drivers of variation in colony size. However, the relative importance of different competitors changed through time. Further, the effect of location increased when colonies took up resources quickly relative to the diffusion of limiting resources. These analyses made it apparent that the importance of location was smaller than expected for experiments with S. enterica growing on glucose. The accumulation of toxic byproducts appeared to limit the growth of large colonies and reduced variation in colony size. Our work provides an experimentally and theoretically grounded understanding of how location interacts with metabolism and diffusion to influence microbial interactions.

Wild chimpanzees plan their breakfast time, type, and location

PubMed Central

Janmaat, Karline R. L.; Polansky, Leo; Ban, Simone Dagui; Boesch, Christophe

2014-01-01

Not all tropical fruits are equally desired by rainforest foragers and some fruit trees get depleted more quickly and carry fruit for shorter periods than others. We investigated whether a ripe-fruit specialist, the chimpanzee (Pan troglodytes verus), arrived earlier at breakfast sites with very ephemeral and highly sought-after fruit, like figs, than sites with less ephemeral fruit that can be more predictably obtained throughout the entire day. We recorded when and where five adult female chimpanzees spent the night and acquired food for a total of 275 full days during three fruit-scarce periods in a West African tropical rainforest. We found that chimpanzees left their sleeping nests earlier (often before sunrise when the forest is still dark) when breakfasting on very ephemeral fruits, especially when they were farther away. Moreover, the females positioned their sleeping nests more in the direction of the next day’s breakfast sites with ephemeral fruit compared with breakfast sites with other fruit. By analyzing departure times and nest positioning as a function of fruit type and location, while controlling for more parsimonious explanations, such as temperature, we found evidence that wild chimpanzees flexibly plan their breakfast time, type, and location after weighing multiple disparate pieces of information. Our study reveals a cognitive mechanism by which large-brained primates can buffer the effects of seasonal declines in food availability and increased interspecific competition to facilitate first access to nutritious food. We discuss the implications for theories on hominoid brain-size evolution. PMID:25349399

Simulation analyses of space use: Home range estimates, variability, and sample size

USGS Publications Warehouse

Bekoff, Marc; Mech, L. David

1984-01-01

Simulations of space use by animals were run to determine the relationship among home range area estimates, variability, and sample size (number of locations). As sample size increased, home range size increased asymptotically, whereas variability decreased among mean home range area estimates generated by multiple simulations for the same sample size. Our results suggest that field workers should ascertain between 100 and 200 locations in order to estimate reliably home range area. In some cases, this suggested guideline is higher than values found in the few published studies in which the relationship between home range area and number of locations is addressed. Sampling differences for small species occupying relatively small home ranges indicate that fewer locations may be sufficient to allow for a reliable estimate of home range. Intraspecific variability in social status (group member, loner, resident, transient), age, sex, reproductive condition, and food resources also have to be considered, as do season, habitat, and differences in sampling and analytical methods. Comparative data still are needed.

SU-E-T-333: Towards Customizable Radiotherapy Enhancement (CuRE) for Prostate Cancer Using Cisplatin Nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sinha, N; Cifter, G; Sajo, E

2014-06-01

Purpose: Replacing routinely used brachytherapy spacers with multifunctional ones loaded with cisplatin nanoparticles (CNP), which can be released into the tumor after implantation, could enable customizable radiation boosting to the prostate tumor in addition to chemotherapy effect. This study investigates the feasibility of customizing the intra-tumor biodistribution and corresponding dose enhancement (DEF) over time for the released CNP as a function of nanoparticle size. Methods: Dose enhancement factors (DEF) due to photon-induced emission of photo-/Auger electrons from CNPs were calculated as a function of concentration using previously published analytical calculation method. An experimentally determined diffusion coefficient (D) for 10 nmmore » nanoparticles in mouse tumor model was employed to estimate D for other sizes using the Stoke- Einstein equation. The error function diffusion model in the experimental study was applied to generate the intra-tumor concentration profile for a burst release of CNPs from the spacer over time. The corresponding DEF profiles were then determined for brachytherapy using Pd-103 and I-125 sources. Results: As expected, the generated profiles showed greater DEF over time for smaller CNP sizes at sample distances from the spacer. For example, for a centrally located spacer, clinically significant DEF (> 20%) could be achieved near the tumor periphery (ca. 0.85 cm distance from the spacer for average PCa tumor size) after 20, and 100 days, respectively for CNPs sizes of 2 nm, and 10 nm, using I-125. Meanwhile for Pd-103, clinically significant DEF could be achieved at the same position after 22 and 108 days, respectively, for same size particles. Conclusion: Our preliminary results demonstrate the feasibility of customizing dose enhancement to prostate tumors as a function of spacer location, brachytherapy source type or size of CNPs released from multifunctional spacers. Such an approach could enable customizable radiation boosting to tumor sub-volumes, while minimizing dose to healthy tissues.« less

Intentional defect array wafers: their practical use in semiconductor control and monitoring systems

NASA Astrophysics Data System (ADS)

Emami, Iraj; McIntyre, Michael; Retersdorf, Michael

2003-07-01

In the competitive world of semiconductor manufacturing today, control of the process and manufacturing equipment is paramount to success of the business. Consistent with the need for rapid development of process technology, is a need for development wiht respect to equipment control including defect metrology tools. Historical control methods for defect metrology tools included a raw count of defects detected on a characterized production or test wafer with little or not regard to the attributes of the detected defects. Over time, these characterized wafers degrade with multiple passes on the tools and handling requiring the tool owner to create and characterize new samples periodically. With the complex engineering software analysis systems used today, there is a strong reliance on the accuracy of defect size, location, and classification in order to provide the best value when correlating the in line to sort type of data. Intentional Defect Array (IDA) wafers were designed and manufacturered at International Sematech (ISMT) in Austin, Texas and is a product of collaboration between ISMT member companies and suppliers of advanced defect inspection equipment. These wafers provide the use with known defect types and sizes in predetermined locations across the entire wafer. The wafers are designed to incorporate several desired flows and use critical dimensions consistent with current and future technology nodes. This paper briefly describes the design of the IDA wafer and details many practical applications in the control of advanced defect inspection equipment.

Optimal placement of multiple types of communicating sensors with availability and coverage redundancy constraints

NASA Astrophysics Data System (ADS)

Vecherin, Sergey N.; Wilson, D. Keith; Pettit, Chris L.

2010-04-01

Determination of an optimal configuration (numbers, types, and locations) of a sensor network is an important practical problem. In most applications, complex signal propagation effects and inhomogeneous coverage preferences lead to an optimal solution that is highly irregular and nonintuitive. The general optimization problem can be strictly formulated as a binary linear programming problem. Due to the combinatorial nature of this problem, however, its strict solution requires significant computational resources (NP-complete class of complexity) and is unobtainable for large spatial grids of candidate sensor locations. For this reason, a greedy algorithm for approximate solution was recently introduced [S. N. Vecherin, D. K. Wilson, and C. L. Pettit, "Optimal sensor placement with terrain-based constraints and signal propagation effects," Unattended Ground, Sea, and Air Sensor Technologies and Applications XI, SPIE Proc. Vol. 7333, paper 73330S (2009)]. Here further extensions to the developed algorithm are presented to include such practical needs and constraints as sensor availability, coverage by multiple sensors, and wireless communication of the sensor information. Both communication and detection are considered in a probabilistic framework. Communication signal and signature propagation effects are taken into account when calculating probabilities of communication and detection. Comparison of approximate and strict solutions on reduced-size problems suggests that the approximate algorithm yields quick and good solutions, which thus justifies using that algorithm for full-size problems. Examples of three-dimensional outdoor sensor placement are provided using a terrain-based software analysis tool.

Joint Optimization of Distribution Network Design and Two-Echelon Inventory Control with Stochastic Demand and CO2 Emission Tax Charges.

PubMed

Li, Shuangyan; Li, Xialian; Zhang, Dezhi; Zhou, Lingyun

2017-01-01

This study develops an optimization model to integrate facility location and inventory control for a three-level distribution network consisting of a supplier, multiple distribution centers (DCs), and multiple retailers. The integrated model addressed in this study simultaneously determines three types of decisions: (1) facility location (optimal number, location, and size of DCs); (2) allocation (assignment of suppliers to located DCs and retailers to located DCs, and corresponding optimal transport mode choices); and (3) inventory control decisions on order quantities, reorder points, and amount of safety stock at each retailer and opened DC. A mixed-integer programming model is presented, which considers the carbon emission taxes, multiple transport modes, stochastic demand, and replenishment lead time. The goal is to minimize the total cost, which covers the fixed costs of logistics facilities, inventory, transportation, and CO2 emission tax charges. The aforementioned optimal model was solved using commercial software LINGO 11. A numerical example is provided to illustrate the applications of the proposed model. The findings show that carbon emission taxes can significantly affect the supply chain structure, inventory level, and carbon emission reduction levels. The delay rate directly affects the replenishment decision of a retailer.

Novel Methods to Determine Feeder Locational PV Hosting Capacity and PV Impact Signatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reno, Matthew J.; Coogan, Kyle; Seuss, John

Often PV hosting capacity analysis is performed for a limited number of distribution feeders. For medium - voltage distribution feeders, previous results generally analyze less than 20 feeders, and then the results are extrapolated out to similar types of feeders. Previous hosting capacity research has often focused on determining a single value for the hosting capacity for the entire feeder, whereas this research expands previous hosting capacity work to investigate all the regions of the feeder that may allow many different hosting capacity values wit h an idea called locational hosting capacity (LHC)to determine the largest PV size that canmore » be interconnected at different locations (buses) on the study feeders. This report discusses novel methods for analyzing PV interconnections with advanced simulati on methods. The focus is feeder and location - specific impacts of PV that determine the locational PV hosting capacity. Feeder PV impact signature are used to more precisely determine the local maximum hosting capacity of individual areas of the feeder. T he feeder signature provides improved interconnection screening with certain zones that show the risk of impact to the distribution feeder from PV interconnections.« less

Thermographic Data Analyses for Karst Watersheds

NASA Technical Reports Server (NTRS)

Campbell, C. Warren; McCaleb, Rebecca C. (Technical Monitor)

2001-01-01

Aerial thermography is an emerging technology unsurpassed for locating groundwater discharges. Thermography can be used to locate submerged discharges that are extremely difficult to find by other means. In two large projects, thermography was used to identify almost every significant spring at sites underlain by karst aquifers. This technology effectively converts Brown's Type 5 topology to types 1 or 2 (all discharges known), which has a significant impact on dye tracing. At a north Alabama site, springs located by thermography quadrupled the known groundwater discharge in and around the site. For submerged discharges, thermographic temperatures can be measured down the center of the groundwater plume that rises to the surface in the winter. Using the Cornell Mixing (CORMIX) model, flow rate for one submerged spring was estimated. Once identified, estimates of spring recharge area were desired. The size of the area of recharge was estimated by hydrograph separation of flow data from nearby, unregulated surface streams. Monthly recharge estimates were also made and used to show that in north Alabama the mean annual recharge/discharge occurs during May and December. Spring flow measurements for the same county of north Alabama were averaged to obtain mean flows. Then measurements for May only, were averaged. The two averages usually agreed to within 20 percent. This provides evidence that hydrograph separation determinations of recharge are valid.

Noise Source Location and Flow Field Measurements on Supersonic Jets and Implications Regarding Broadband Shock Noise

NASA Technical Reports Server (NTRS)

Podboy, Gary G.; Wernet, Mark P.; Clem, Michelle M.; Fagan, Amy F.

2017-01-01

An experiment was conducted in an effort to obtain data that would provide a better understanding of the origins of broadband shock noise (BBSN). Phased array noise source location and two types of flow field data (background oriented schlieren and particle image velocimetry) were acquired on unheated, single-stream jets. Results are presented for one subsonic and four supersonic operating conditions. These data show that BBSN is created primarily in the downstream portion of the shock train with peak BBSN production occurring near where the average size of the turbulent structures is equal to the shockcell spacing. These data tend to validate theories that BBSN is created by turbulent structures that are as large or larger than the shock spacing.

Computer Modelling and Simulation of Solar PV Array Characteristics

NASA Astrophysics Data System (ADS)

Gautam, Nalin Kumar

2003-02-01

The main objective of my PhD research work was to study the behaviour of inter-connected solar photovoltaic (PV) arrays. The approach involved the construction of mathematical models to investigate different types of research problems related to the energy yield, fault tolerance, efficiency and optimal sizing of inter-connected solar PV array systems. My research work can be divided into four different types of research problems: 1. Modeling of inter-connected solar PV array systems to investigate their electrical behavior, 2. Modeling of different inter-connected solar PV array networks to predict their expected operational lifetimes, 3. Modeling solar radiation estimation and its variability, and 4. Modeling of a coupled system to estimate the size of PV array and battery-bank in the stand-alone inter-connected solar PV system where the solar PV system depends on a system providing solar radiant energy. The successful application of mathematics to the above-m entioned problems entailed three phases: 1. The formulation of the problem in a mathematical form using numerical, optimization, probabilistic and statistical methods / techniques, 2. The translation of mathematical models using C++ to simulate them on a computer, and 3. The interpretation of the results to see how closely they correlated with the real data. Array is the most cost-intensive component of the solar PV system. Since the electrical performances as well as life properties of an array are highly sensitive to field conditions, different characteristics of the arrays, such as energy yield, operational lifetime, collector orientation, and optimal sizing were investigated in order to improve their efficiency, fault-tolerance and reliability. Three solar cell interconnection configurations in the array - series-parallel, total-cross-tied, and bridge-linked, were considered. The electrical characteristics of these configurations were investigated to find out one that is comparatively less susceptible to the mismatches due to manufacturer's tolerances in cell characteristics, shadowing, soiling and aging of solar cells. The current-voltage curves and the values of energy yield characterized by maximum-power points and fill factors for these arrays were also obtained. Two different mathematical models, one for smaller size arrays and the other for the larger size arrays, were developed. The first model takes account of the partial differential equations with boundary value conditions, whereas the second one involves the simple linear programming concept. Based on the initial information on the values of short-circuit current and open-circuit voltage of thirty-six single-crystalline silicon solar cells provided by a manufacturer, the values of these parameters for up to 14,400 solar cells were generated randomly. Thus, the investigations were done for three different cases of array sizes, i.e., (6 x 6), (36 x 8) and (720 x 20), for each configuration. The operational lifetimes of different interconnected solar PV arrays and the improvement in their life properties through different interconnection and modularized configurations were investigated using a reliability-index model. Under normal conditions, the efficiency of a solar cell degrades in an exponential manner, and its operational life above a lowest admissible efficiency may be considered as the upper bound of its lifetime. Under field conditions, the solar cell may fail any time due to environmental stresses, or it may function up to the end of its expected lifetime. In view of this, the lifetime of a solar cell in an array was represented by an exponentially distributed random variable. At any instant of time t, this random variable was considered to have two states: (i) the cell functioned till time t, or (ii) the cell failed within time t. It was considered that the functioning of the solar cell included its operation at an efficiency decaying with time under normal conditions. It was assumed that the lifetime of a solar cell had lack of memory or aging property, which meant that no matter how long (say, t) the cell had been operational, the probability that it would last an additional time ?t was independent of t. The operational life of the solar cell above a lowest admissible efficiency was considered as the upper bound of its expected lifetime. The value of the upper bound on the expected life of solar cell was evaluated using the information provided by the manufacturers of the single-crystalline silicon solar cells. Then on the basis of these lifetimes, the expected operational lifetimes of the array systems were obtained. Since the investigations of the effects of collector orientation on the performance of an array require the continuous values of global solar radiation on a surface, a method to estimate the global solar radiation on a surface (horizontal or tilted) was also proposed. The cloudiness index was defined as the fraction of extraterrestrial radiation that reached the earth's surface when the sky above the location of interest was obscured by the cloud cover. The cloud cover at the location of interest during any time interval of a day was assumed to follow the fuzzy random phenomenon. The cloudiness index, therefore, was considered as a fuzzy random variable that accounted for the cloud cover at the location of interest during any time interval of a day. This variable was assumed to depend on four other fuzzy random variables that, respectively, accounted for the cloud cover corresponding to the 1) type of cloud group, 2) climatic region, 3) season with most of the precipitation, and 4) type of precipitation at the location of interest during any time interval. All possible types of cloud covers were categorized into five types of cloud groups. Each cloud group was considered to be a fuzzy subset. In this model, the cloud cover at the location of interest during a time interval was considered to be the clouds that obscure the sky above the location. The cloud covers, with all possible types of clouds having transmissivities corresponding to values in the membership range of a fuzzy subset (i.e., a type of cloud group), were considered to be the membership elements of that fuzzy subset. The transmissivities of different types of cloud covers in a cloud group corresponded to the values in the membership range of that cloud group. Predicate logic (i.e., if---then---, else---, conditions) was used to set the relationship between all the fuzzy random variables. The values of the above-mentioned fuzzy random variables were evaluated to provide the value of cloudiness index for each time interval at the location of interest. For each case of the fuzzy random variable, heuristic approach was used to identify subjectively the range ([a, b], where a and b were real numbers with in [0, 1] such that a

Characterization of tropical precipitation using drop size distribution and rain rate-radar reflectivity relation

NASA Astrophysics Data System (ADS)

Das, Saurabh; Maitra, Animesh

2018-04-01

Characterization of precipitation is important for proper interpretation of rain information from remotely sensed data. Rain attenuation and radar reflectivity (Z) depend directly on the drop size distribution (DSD). The relation between radar reflectivity/rain attenuation and rain rate (R) varies widely depending upon the origin, topography, and drop evolution mechanism and needs further understanding of the precipitation characteristics. The present work utilizes 2 years of concurrent measurements of DSD using a ground-based disdrometer at five diverse climatic conditions in Indian subcontinent and explores the possibility of rain classification based on microphysical characteristics of precipitation. It is observed that both gamma and lognormal distributions are performing almost similar for Indian region with a marginally better performance by one model than other depending upon the locations. It has also been found that shape-slope relationship of gamma distribution can be a good indicator of rain type. The Z-R relation, Z = ARb, is found to vary widely for different precipitation systems, with convective rain that has higher values of A than the stratiform rain for two locations, whereas the reverse is observed for the rest of the three locations. Further, the results indicate that the majority of rainfall (>50%) in Indian region is due to the convective rain although the occurrence time of convective rain is low (<10%).

Clinic exam room design: present and future.

PubMed

Freihoefer, Kara; Nyberg, Gary; Vickery, Christine

2013-01-01

This article aims to deconstruct various design qualities and strategies of clinic exam rooms, and discuss how they influence users' interaction and behavior in the space. Relevant literature supports the advantages and disadvantages of different design strategies. Annotated exam room prototypes illustrate the design qualities and strategies discussed. Advancements in technology and medicine, along with new legislative policies, are influencing the way care providers deliver care and ultimately clinic exam room designs. The patient-centered medical home model has encouraged primary care providers to make patients more active leaders of their health plan which will influence the overall functionality and configuration of clinic exam rooms. Specific design qualities discussed include overall size, location of doors and privacy curtains, positioning of exam tables, influence of technology in the consultation area, types of seating, and placement of sink and hand sanitizing dispensers. In addition, future trends of exam room prototypes are presented. There is a general lack of published evidence to support design professionals' design solutions for outpatient exam rooms. Future research should investigate such topics as the location of exam tables and privacy curtains as they relate to patient privacy; typical size and location of consultation table as it relates to patient connection and communication; and placement of sinks and sanitization dispensers as they relate to frequency and patterns of usage. Literature review, outpatient, technology, visual privacy.

First light from student Pascal Keller, Eschenbach/Switzerland on 6-8 June 2014

NASA Astrophysics Data System (ADS)

Monstein, Christian

2014-05-01

Pascal Keller, a student during his exams for general qualification for university entrance, recently set up a Long Wavelength Array (LWA) antenna and a Callisto system to observe solar radio burst activity in his back yard (figure 1) in Eschenbach, Switzerland. The antenna, spectrometer and software were provided on loan by Institute for Astronomy, ETH Zurich. On the first observation day he observed his 1st light, a type II solar radio burst and some type III bursts. His aim is now to compare this LWA observation with others from the e-Callisto network, which is composed of different antenna types and different antenna sizes as well different locations worldwide. His first four observations on 6 and 8 June 2014 are presented in figures 2 to 5 and associated tables 1 to 4.

The fundamentals of average local variance--Part I: Detecting regular patterns.

PubMed

Bøcher, Peder Klith; McCloy, Keith R

2006-02-01

The method of average local variance (ALV) computes the mean of the standard deviation values derived for a 3 x 3 moving window on a successively coarsened image to produce a function of ALV versus spatial resolution. In developing ALV, the authors used approximately a doubling of the pixel size at each coarsening of the image. They hypothesized that ALV is low when the pixel size is smaller than the size of scene objects because the pixels on the object will have similar response values. When the pixel and objects are of similar size, they will tend to vary in response and the ALV values will increase. As the size of pixels increase further, more objects will be contained in a single pixel and ALV will decrease. The authors showed that various cover types produced single peak ALV functions that inexplicitly peaked when the pixel size was 1/2 to 3/4 of the object size. This paper reports on work done to explore the characteristics of the various forms of the ALV function and to understand the location of the peaks that occur in this function. The work was conducted using synthetically generated image data. The investigation showed that the hypothesis originally proposed in is not adequate. A new hypothesis is proposed that the ALV function has peak locations that are related to the geometric size of pattern structures in the scene. These structures are not always the same as scene objects. Only in cases where the size of and separation between scene objects are equal does the ALV function detect the size of the objects. In situations where the distance between scene objects are larger than their size, the ALV function has a peak at the object separation, not at the object size. This work has also shown that multiple object structures of different sizes and distances in the image provide multiple peaks in the ALV function and that some of these structures are not implicitly recognized as such from our perspective. However, the magnitude of these peaks depends on the response mix in the structures, complicating their interpretation and analysis. The analysis of the ALV Function is, thus, more complex than that generally reported in the literature.

A spectral clustering search algorithm for predicting shallow landslide size and location

Treesearch

Dino Bellugi; David G. Milledge; William E. Dietrich; Jim A. McKean; J. Taylor Perron; Erik B. Sudderth; Brian Kazian

2015-01-01

The potential hazard and geomorphic significance of shallow landslides depend on their location and size. Commonly applied one-dimensional stability models do not include lateral resistances and cannot predict landslide size. Multi-dimensional models must be applied to specific geometries, which are not known a priori, and testing all possible geometries is...

Individual variation in nest size and nest site features of the Bornean orangutans (Pongo pygmaeus).

PubMed

Rayadin, Yaya; Saitoh, Takashi

2009-05-01

Nest construction is a daily habit of independent orangutans for sleeping or resting. Data on their nests have been used in various ecological studies (e.g., density estimation, ranging behavior, evolution of material culture) because they are the most observable field signs. We investigated nest size and nest site features of Bornean orangutans in the wild during 10 months' fieldwork at three sites in East Kalimantan, Indonesia: Kutai National Park, Birawa, and Meratus. To examine individual variation, we followed 31 individual orangutans and recorded the 92 nests they made for nest size (diameter) and nest site features (height of nest above ground, tree species used for the nest site, the diameter and height of the tree, whether the nest was new or reused, and nest location within the tree). Analyses taking age-sex classes of the focal individuals into consideration showed significant age-sex differences in nest size and location, but not in nest height or nest tree features (diameter, height of tree, and height of lowest branch). Mature orangutans (adult females, unflanged and flanged males) made larger nests than immatures (juveniles and adolescents). Flanged male orangutans with larger nests used stable locations for nesting sites and reused old nests more frequently than immatures. The overall proportion of nests in open (exposed) locations was higher than in closed (sheltered) locations. Flanged males and immatures frequently made open nests, whereas adult females with an infant preferred closed locations. The good correspondence between nest size and age-sex classes indicates that nest size variation may reflect body size and therefore age-sex variation in the population. (c) 2009 Wiley-Liss, Inc.

Optical-NIR dust extinction towards Galactic O stars

NASA Astrophysics Data System (ADS)

Maíz Apellániz, J.; Barbá, R. H.

2018-05-01

Context. O stars are excellent tracers of the intervening ISM because of their high luminosity, blue intrinsic SED, and relatively featureless spectra. We are currently conducting the Galactic O-Star Spectroscopic Survey (GOSSS), which is generating a large sample of O stars with accurate spectral types within several kpc of the Sun. Aims: We aim to obtain a global picture of the properties of dust extinction in the solar neighborhood based on optical-NIR photometry of O stars with accurate spectral types. Methods: We have processed a carefully selected photometric set with the CHORIZOS code to measure the amount [E(4405 - 5495)] and type [R5495] of extinction towards 562 O-type stellar systems. We have tested three different families of extinction laws and analyzed our results with the help of additional archival data. Results: The Maíz Apellániz et al. (2014, A&A, 564, A63) family of extinction laws provides a better description of Galactic dust that either the Cardelli et al. (1989, ApJ, 345, 245) or Fitzpatrick (1999, PASP, 111, 63) families, so it should be preferentially used when analysing samples similar to the one in this paper. In many cases O stars and late-type stars experience similar amounts of extinction at similar distances but some O stars are located close to the molecular clouds left over from their births and have larger extinctions than the average for nearby late-type populations. In qualitative terms, O stars experience a more diverse extinction than late-type stars, as some are affected by the small-grain-size, low-R5495 effect of molecular clouds and others by the large-grain-size, high-R5495 effect of H II regions. Late-type stars experience a narrower range of grain sizes or R5495, as their extinction is predominantly caused by the average, diffuse ISM. We propose that the reason for the existence of large-grain-size, high-R5495 regions in the ISM in the form of H II regions and hot-gas bubbles is the selective destruction of small dust grains by EUV photons and possibly by thermal sputtering by atoms or ions. Table 1 is only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/613/A9

Nanopores creation in boron and nitrogen doped polycrystalline graphene: A molecular dynamics study

NASA Astrophysics Data System (ADS)

Izadifar, Mohammadreza; Abadi, Rouzbeh; Nezhad Shirazi, Ali Hossein; Alajlan, Naif; Rabczuk, Timon

2018-05-01

In the present paper, molecular dynamic simulations have been conducted to investigate the nanopores creation on 10% of boron and nitrogen doped polycrystalline graphene by silicon and diamond nanoclusters. Two types of nanoclusters based on silicon and diamond are used to investigate their effect for the fabrication of nanopores. Therefore, three different diameter sizes of the clusters with five kinetic energies of 10, 50, 100, 300 and 500 eV/atom at four different locations in boron or nitrogen doped polycrystalline graphene nanosheets have been perused. We also study the effect of 3% and 6% of boron doped polycrystalline graphene with the best outcome from 10% of doping. Our results reveal that the diamond cluster with diameter of 2 and 2.5 nm fabricates the largest nanopore areas on boron and nitrogen doped polycrystalline graphene, respectively. Furthermore, the kinetic energies of 10 and 50 eV/atom can not fabricate nanopores in some cases for silicon and diamond clusters on boron doped polycrystalline graphene nanosheets. On the other hand, silicon and diamond clusters fabricate nanopores for all locations and all tested energies on nitrogen doped polycrystalline graphene. The area sizes of nanopores fabricated by silicon and diamond clusters with diameter of 2 and 2.5 nm are close to the actual area size of the related clusters for the kinetic energy of 300 eV/atom in all locations on boron doped polycrystalline graphene. The maximum area and the average maximum area of nanopores are fabricated by the kinetic energy of 500 eV/atom inside the grain boundary at the center of the nanosheet and in the corner of nanosheet with diameters of 2 and 3 nm for silicon and diamond clusters on boron and nitrogen doped polycrystalline graphene.

Management of Anterior Skull Base Defect Depending on Its Size and Location

PubMed Central

Bernal-Sprekelsen, Manuel; Rioja, Elena; Enseñat, Joaquim; Enriquez, Karla; Viscovich, Liza; Agredo-Lemos, Freddy Enrique; Alobid, Isam

2014-01-01

Introduction. We present our experience in the reconstruction of these leaks depending on their size and location. Material and Methods. Fifty-four patients who underwent advanced skull base surgery (large defects, >20 mm) and 62 patients with CSF leaks of different origin (small, 2–10 mm, and midsize, 11–20 mm, defects) were included in the retrospective study. Large defects were reconstructed with a nasoseptal pedicled flap positioned on fat and fascia lata. In small and midsized leaks. Fascia lata in an underlay position was used for its reconstruction covered with mucoperiosteum of either the middle or the inferior turbinate. Results. The most frequent etiology for small and midsized defects was spontaneous (48.4%), followed by trauma (24.2%), iatrogenic (5%). The success rate after the first surgical reconstruction was 91% and 98% in large skull base defects and small/midsized, respectively. Rescue surgery achieved 100%. Conclusions. Endoscopic surgery for any type of skull base defect is the gold standard. The size of the defects does not seem to play a significant role in the success rate. Fascia lata and mucoperiosteum of the turbinate allow a two-layer reconstruction of small and midsized defects. For larger skull base defects, a combination of fat, fascia lata, and nasoseptal pedicled flaps provides a successful reconstruction. PMID:24895567

Multivariate Visualization in Social Sciences and Survey Data

DTIC Science & Technology

2013-09-01

uses bubbles indicating Walmart store locations. The bubble size is misleading as it does not reflect the amount of stores or the size of any store...displaying survey data, the bubbles’ exact location is relevant, indicating Walmart store locations. Yau’s choropleth (Figure 2.7, right chart) displays...is able to see the embedded image. 14 Figure 2.7: Point-based bubbles (left) display the the locations of Walmart stores at some point in the stores

Effects of disc mid-plane evolution on CO snowline location

NASA Astrophysics Data System (ADS)

Panić, O.; Min, M.

2017-05-01

Temperature changes in the planet forming disc mid-planes carry important physico-chemical consequences, such as the effect on the locations of the condensation fronts of molecules - the snowlines. Snowlines impose major chemical gradients and possibly foster grain growth. The aim of this paper is to understand how disc mid-plane temperature changes with gas and dust evolution, and identify trends that may influence planet formation or allow to constrain disc evolution observationally. We calculate disc temperature, hydrostatic equilibrium and dust settling in a mutually consistent way from a grid of disc models at different stages of gas loss, grain growth and hole opening. We find that the CO snowline location depends very strongly on disc properties. The CO snowline location migrates closer to the star for increasing degrees of gas dispersal and dust growth. Around a typical A-type star, the snowline can be anywhere between several tens and a few hundred au, depending on the disc properties such as gas mass and grain size. In fact, gas loss is as efficient as dust evolution in settling discs, and flat discs may be gas-poor counterparts of flared discs. Our results, in the context of different pre-main-sequence evolution of the luminosity in low- and intermediate-mass stars suggest very different thermal (and hence chemical) histories in these two types of discs. Discs of T Tauri stars settle and cool down, while discs of Herbig Ae stars may remain rather warm throughout the pre-main sequence.

The differences in imaging features of malignant and benign branch duct type of Intraductal Papillary Mucinous Tumor.

PubMed

Zhang, Hui-mao; Yao, Fang; Liu, Gui-feng; Wang, Xiao-bin; Xiu, Dian-hui; Gen, Iinuma

2011-12-01

To investigate the difference in the radiological features of malignant and benign branch duct type of IPMT (Intraductal Papillary Mucinous Tumor) of the pancreas. Thirty-six patients who were referred for operation with branch duct type of IPMT of the pancreas were included in this study. All cases underwent both CT and MRI with contrast enhancement. The size of the cystic lesions, the presence and size of mural nodules, and the amount of dilatation of the MPD were assessed by two independent radiologists, and the results were compared with pathological findings. Histological examination revealed adenoma in 8 cases, AH (atypical hyperplasia) in 8 cases, CIS (carcinoma in situ) in 8 cases and invasive carcinoma in 12 cases. Patients of the malignant group were older than those in the benign group (mean age: 67 yrs vs 60 yrs, respectively), but no statistically significant (p=0.05). Males (16/4 vs 10/6) more often complained weight loss and jaundice. The malignant tumor was more frequently located in the head-body and body. Compared with the benign group, the mean sizes of the cyst, mural nodules, MPD of the malignant group were 44 mm, 13 mm, 7.5 mm and benign group were 31 mm, 5 mm, 3.5 mm respectively. All these difference are statistically significant (p<0.05). In 4 cases of the 20 in the malignant group, soft tissue suggesting spread of disease into the adjacent viscera and peritoneum was detected. Cyst size over 30 mm and mural nodule over 8 mm, irregular thick septa, dilatation of the MPD, and accompany with soft tissue mass may be helpful factors in determining malignancy. Copyright © 2011. Published by Elsevier Ireland Ltd.

SDSS-IV MaNGA: global stellar population and gradients for about 2000 early-type and spiral galaxies on the mass-size plane

NASA Astrophysics Data System (ADS)

Li, Hongyu; Mao, Shude; Cappellari, Michele; Ge, Junqiang; Long, R. J.; Li, Ran; Mo, H. J.; Li, Cheng; Zheng, Zheng; Bundy, Kevin; Thomas, Daniel; Brownstein, Joel R.; Roman Lopes, Alexandre; Law, David R.; Drory, Niv

2018-05-01

We perform full spectrum fitting stellar population analysis and Jeans Anisotropic modelling of the stellar kinematics for about 2000 early-type galaxies (ETGs) and spiral galaxies from the MaNGA DR14 sample. Galaxies with different morphologies are found to be located on a remarkably tight mass plane which is close to the prediction of the virial theorem, extending previous results for ETGs. By examining an inclined projection (`the mass-size' plane), we find that spiral and early-type galaxies occupy different regions on the plane, and their stellar population properties (i.e. age, metallicity, and stellar mass-to-light ratio) vary systematically along roughly the direction of velocity dispersion, which is a proxy for the bulge fraction. Galaxies with higher velocity dispersions have typically older ages, larger stellar mass-to-light ratios and are more metal rich, which indicates that galaxies increase their bulge fractions as their stellar populations age and become enriched chemically. The age and stellar mass-to-light ratio gradients for low-mass galaxies in our sample tend to be positive (centre < outer), while the gradients for most massive galaxies are negative. The metallicity gradients show a clear peak around velocity dispersion log10 σe ≈ 2.0, which corresponds to the critical mass ˜3 × 1010 M⊙ of the break in the mass-size relation. Spiral galaxies with large mass and size have the steepest gradients, while the most massive ETGs, especially above the critical mass Mcrit ≳ 2 × 1011 M⊙, where slow rotator ETGs start dominating, have much flatter gradients. This may be due to differences in their evolution histories, e.g. mergers.

Anterior chamber blood cell differentiation using spectroscopic optical coherence tomography

NASA Astrophysics Data System (ADS)

Qian, Ruobing; McNabb, Ryan P.; Kuo, Anthony N.; Izatt, Joseph A.

2018-02-01

There is great clinical importance in identifying cellular responses in the anterior chamber (AC) which can indicate signs of hyphema (an accumulation of red blood cells (RBCs)) or aberrant intraocular inflammation (an accumulation of white blood cells (WBCs)). These responses are difficult to diagnose and require specialized equipment such as ophthalmic microscopes and specialists trained in examining the eye. In this work, we applied spectroscopic OCT to differentiate between RBCs and subtypes of WBCs, including neutrophils, lymphocytes and monocytes, both in vitro and in ACs of porcine eyes. We located and tracked single cells in OCT volumetric images, and extracted the spectroscopic data of each cell from the detected interferograms using short-time Fourier Transform (STFT). A look-up table of Mie spectra was generated and used to correlate the spectroscopic data of single cells to their characteristic sizes. The accuracy of the method was first validated on 10um polystyrene microspheres. For RBCs and subtypes of WBCs, the extracted size distributions based on the best Mie spectra fit were significantly different between each cell type by using the Wilcoxon rank-sum test. A similar size distribution of neutrophils was also acquired in the measurements of cells introduced into the ACs of porcine eyes, further supporting spectroscopic OCT for potentially differentiating and quantifying blood cell types in the AC in vivo.

Prediction of the location and size of the stomach using patient characteristics for retrospective radiation dose estimation following radiotherapy

PubMed Central

Lamart, Stephanie; Imran, Rebecca; Simon, Steven L.; Doi, Kazutaka; Morton, Lindsay M.; Curtis, Rochelle E.; Lee, Choonik; Drozdovitch, Vladimir; Maass-Moreno, Roberto; Chen, Clara C.; Whatley, Millie; Miller, Donald L.; Pacak, Karel; Lee, Choonsik

2014-01-01

Following cancer radiotherapy, reconstruction of doses to organs, other than the target organ, is of interest for retrospective health risk studies. Reliable estimation of doses to organs that may be partially within or fully outside the treatment field requires reliable knowledge of the location and size of the organs, e.g., the stomach, which is at risk from abdominal irradiation. The stomach location and size are known to be highly variable between individuals, but have been little studied. Moreover, for treatments conducted years ago, medical images of patients are usually not available in medical records to locate the stomach. In light of the poor information available to locate the stomach in historical dose reconstructions, the purpose of this work was to investigate the variability of stomach location and size among adult male patients and to develop prediction models for the stomach location and size using predictor variables generally available in medical records of radiotherapy patients treated in the past. To collect data on stomach size and position, we segmented the contours of the stomach and of the skeleton on contemporary Computed Tomography (CT) images for 30 male patients in supine position. The location and size of the stomach was found to depend on body mass index (BMI), ponderal index (PI), and age. For example, the anteroposterior dimension of the stomach was found to increase with increasing BMI (≈0.25 cm per kg/m2) whereas its craniocaudal dimension decreased with increasing PI (≈ −3.3 cm per kg/m3) and its transverse dimension increased with increasing PI (≈ 2.5 cm per kg/m3). Using the prediction models, we generated three dimensional computational stomach models from a deformable hybrid phantom for three patients of different BMI. Based on a typical radiotherapy treatment, we simulated radiotherapy treatments on the predicted stomach models and on the CT images of the corresponding patients. Those dose calculations demonstrated good agreement between predicted and actual stomachs compared with doses derived from a reference model of the body that might be used in the absence of individual CT scan data. PMID:24301086

Prediction of the location and size of the stomach using patient characteristics for retrospective radiation dose estimation following radiotherapy

NASA Astrophysics Data System (ADS)

Lamart, Stephanie; Imran, Rebecca; Simon, Steven L.; Doi, Kazutaka; Morton, Lindsay M.; Curtis, Rochelle E.; Lee, Choonik; Drozdovitch, Vladimir; Maass-Moreno, Roberto; Chen, Clara C.; Whatley, Millie; Miller, Donald L.; Pacak, Karel; Lee, Choonsik

2013-12-01

Following cancer radiotherapy, reconstruction of doses to organs, other than the target organ, is of interest for retrospective health risk studies. Reliable estimation of doses to organs that may be partially within or fully outside the treatment field requires reliable knowledge of the location and size of the organs, e.g., the stomach, which is at risk from abdominal irradiation. The stomach location and size are known to be highly variable between individuals, but have been little studied. Moreover, for treatments conducted years ago, medical images of patients are usually not available in medical records to locate the stomach. In light of the poor information available to locate the stomach in historical dose reconstructions, the purpose of this work was to investigate the variability of stomach location and size among adult male patients and to develop prediction models for the stomach location and size using predictor variables generally available in medical records of radiotherapy patients treated in the past. To collect data on stomach size and position, we segmented the contours of the stomach and of the skeleton on contemporary computed tomography (CT) images for 30 male patients in supine position. The location and size of the stomach was found to depend on body mass index (BMI), ponderal index (PI), and age. For example, the anteroposterior dimension of the stomach was found to increase with increasing BMI (≈0.25 cm kg-1 m2) whereas its craniocaudal dimension decreased with increasing PI (≈-3.3 cm kg-1 m3) and its transverse dimension increased with increasing PI (≈2.5 cm kg-1 m3). Using the prediction models, we generated three-dimensional computational stomach models from a deformable hybrid phantom for three patients of different BMI. Based on a typical radiotherapy treatment, we simulated radiotherapy treatments on the predicted stomach models and on the CT images of the corresponding patients. Those dose calculations demonstrated good agreement between predicted and actual stomachs compared with doses derived from a reference model of the body that might be used in the absence of individual CT scan data.

Mapping coastal marine debris using aerial imagery and spatial analysis.

PubMed

Moy, Kirsten; Neilson, Brian; Chung, Anne; Meadows, Amber; Castrence, Miguel; Ambagis, Stephen; Davidson, Kristine

2017-12-19

This study is the first to systematically quantify, categorize, and map marine macro-debris across the main Hawaiian Islands (MHI), including remote areas (e.g., Niihau, Kahoolawe, and northern Molokai). Aerial surveys were conducted over each island to collect high resolution photos, which were processed into orthorectified imagery and visually analyzed in GIS. The technique provided precise measurements of the quantity, location, type, and size of macro-debris (>0.05m 2 ), identifying 20,658 total debris items. Northeastern (windward) shorelines had the highest density of debris. Plastics, including nets, lines, buoys, floats, and foam, comprised 83% of the total count. In addition, the study located six vessels from the 2011 Tōhoku tsunami. These results created a baseline of the location, distribution, and composition of marine macro-debris across the MHI. Resource managers and communities may target high priority areas, particularly along remote coastlines where macro-debris counts were largely undocumented. Copyright © 2017 Elsevier Ltd. All rights reserved.

Severity of electrical accidents in the construction industry in Spain.

PubMed

Suárez-Cebador, Manuel; Rubio-Romero, Juan Carlos; López-Arquillos, Antonio

2014-02-01

This paper analyzes the severity of workplace accidents involving electricity in the Spanish construction sector comprising 2,776 accidents from 2003 to 2008. The investigation considered the impact of 13 variables, classified into 5 categories: Personal, Business, Temporal, Material, and Spatial. The findings showed that electrical accidents are almost five times more likely to have serious consequences than the average accident in the sector and it also showed how the variables of age, occupation, company size, length of service, preventive measures, time of day, days of absence, physical activity, material agent, type of injury, body part injured, accident location, and type of location are related to the severity of the electrical accidents under consideration. The present situation makes it clear that greater effort needs to be made in training, monitoring, and signage to guarantee a safe working environment in relation to electrical hazards. This research enables safety technicians, companies, and government officials to identify priorities and to design training strategies to minimize the serious consequences of electrical accidents for construction workers. Copyright © 2013 Elsevier Ltd and National Safety Council. All rights reserved.

13 CFR 121.303 - What size procedures are used by SBA before it makes a formal size determination?

Code of Federal Regulations, 2010 CFR

2010-01-01

... source. (b) A small business investment company, a development company, a surety bond company, or a... area in which the headquarters of the applicant is located, regardless of the location of the parent company or affiliates. For disaster loan assistance, the request for a size determination must be made to...

Discovery of Temperate Earth-Sized Planets Transiting a Nearby Ultracool Dwarf Star

NASA Technical Reports Server (NTRS)

Jehin, Emmanuel; Gillon, Michael; Lederer, Susan M.; Delrez, Laetitia; De Wit, Julien; Burdanov, Artem; Van Grootel, Valerie; Burgasser, Adam; Triaud, Amaury; Demory, Brice-Olivier;

Soil data from Picea mariana stands near delta junction, Alaska of different ages and soil drainage type

USGS Publications Warehouse

Manies, Kristen L.; Harden, Jennifer W.; Silva, Steven R.; Briggs, Paul H.; Schmid, Brian M.

2004-01-01

The U.S. Geological Survey project Fate of Carbon in Alaskan Landscapes (FOCAL) is studying the effect of fire and soil drainage on soil carbon storage in the boreal forest. This project has selected several sites to study within central Alaska of varying ages (time since fire) and soil drainage types. This report describes the location of these sampling sites, as well as the procedures used to describe, sample, and analyze the soils. This report also contains data tables with this information, including, but not limited to field descriptions, bulk density, particle size distribution, moisture content, carbon (C) concentration, nitrogen (N) concentration, isotopic data for C, and major, minor and trace elemental concentration.

Quantile regression of microgeographic variation in population characteristics of an invasive vertebrate predator

USGS Publications Warehouse

Siers, Shane R.; Savidge, Julie A.; Reed, Robert

2017-01-01

Localized ecological conditions have the potential to induce variation in population characteristics such as size distributions and body conditions. The ability to generalize the influence of ecological characteristics on such population traits may be particularly meaningful when those traits influence prospects for successful management interventions. To characterize variability in invasive Brown Treesnake population attributes within and among habitat types, we conducted systematic and seasonally-balanced surveys, collecting 100 snakes from each of 18 sites: three replicates within each of six major habitat types comprising 95% of Guam’s geographic expanse. Our study constitutes one of the most comprehensive and controlled samplings of any published snake study. Quantile regression on snake size and body condition indicated significant ecological heterogeneity, with a general trend of relative consistency of size classes and body conditions within and among scrub and Leucaena forest habitat types and more heterogeneity among ravine forest, savanna, and urban residential sites. Larger and more robust snakes were found within some savanna and urban habitat replicates, likely due to relative availability of larger prey. Compared to more homogeneous samples in the wet season, variability in size distributions and body conditions was greater during the dry season. Although there is evidence of habitat influencing Brown Treesnake populations at localized scales (e.g., the higher prevalence of larger snakes—particularly males—in savanna and urban sites), the level of variability among sites within habitat types indicates little ability to make meaningful predictions about these traits at unsampled locations. Seasonal variability within sites and habitats indicates that localized population characterization should include sampling in both wet and dry seasons. Extreme values at single replicates occasionally influenced overall habitat patterns, while pooling replicates masked variability among sites. A full understanding of population characteristics should include an assessment of variability both at the site and habitat level.

Quantile regression of microgeographic variation in population characteristics of an invasive vertebrate predator

PubMed Central

Siers, Shane R.; Savidge, Julie A.; Reed, Robert N.

2017-01-01

Localized ecological conditions have the potential to induce variation in population characteristics such as size distributions and body conditions. The ability to generalize the influence of ecological characteristics on such population traits may be particularly meaningful when those traits influence prospects for successful management interventions. To characterize variability in invasive Brown Treesnake population attributes within and among habitat types, we conducted systematic and seasonally-balanced surveys, collecting 100 snakes from each of 18 sites: three replicates within each of six major habitat types comprising 95% of Guam’s geographic expanse. Our study constitutes one of the most comprehensive and controlled samplings of any published snake study. Quantile regression on snake size and body condition indicated significant ecological heterogeneity, with a general trend of relative consistency of size classes and body conditions within and among scrub and Leucaena forest habitat types and more heterogeneity among ravine forest, savanna, and urban residential sites. Larger and more robust snakes were found within some savanna and urban habitat replicates, likely due to relative availability of larger prey. Compared to more homogeneous samples in the wet season, variability in size distributions and body conditions was greater during the dry season. Although there is evidence of habitat influencing Brown Treesnake populations at localized scales (e.g., the higher prevalence of larger snakes—particularly males—in savanna and urban sites), the level of variability among sites within habitat types indicates little ability to make meaningful predictions about these traits at unsampled locations. Seasonal variability within sites and habitats indicates that localized population characterization should include sampling in both wet and dry seasons. Extreme values at single replicates occasionally influenced overall habitat patterns, while pooling replicates masked variability among sites. A full understanding of population characteristics should include an assessment of variability both at the site and habitat level. PMID:28570632

Quantile regression of microgeographic variation in population characteristics of an invasive vertebrate predator.

PubMed

Siers, Shane R; Savidge, Julie A; Reed, Robert N

2017-01-01

Localized ecological conditions have the potential to induce variation in population characteristics such as size distributions and body conditions. The ability to generalize the influence of ecological characteristics on such population traits may be particularly meaningful when those traits influence prospects for successful management interventions. To characterize variability in invasive Brown Treesnake population attributes within and among habitat types, we conducted systematic and seasonally-balanced surveys, collecting 100 snakes from each of 18 sites: three replicates within each of six major habitat types comprising 95% of Guam's geographic expanse. Our study constitutes one of the most comprehensive and controlled samplings of any published snake study. Quantile regression on snake size and body condition indicated significant ecological heterogeneity, with a general trend of relative consistency of size classes and body conditions within and among scrub and Leucaena forest habitat types and more heterogeneity among ravine forest, savanna, and urban residential sites. Larger and more robust snakes were found within some savanna and urban habitat replicates, likely due to relative availability of larger prey. Compared to more homogeneous samples in the wet season, variability in size distributions and body conditions was greater during the dry season. Although there is evidence of habitat influencing Brown Treesnake populations at localized scales (e.g., the higher prevalence of larger snakes-particularly males-in savanna and urban sites), the level of variability among sites within habitat types indicates little ability to make meaningful predictions about these traits at unsampled locations. Seasonal variability within sites and habitats indicates that localized population characterization should include sampling in both wet and dry seasons. Extreme values at single replicates occasionally influenced overall habitat patterns, while pooling replicates masked variability among sites. A full understanding of population characteristics should include an assessment of variability both at the site and habitat level.

The role of size of input box, location of input box, input method and display size in Chinese handwriting performance and preference on mobile devices.

PubMed

Chen, Zhe; Rau, Pei-Luen Patrick

2017-03-01

This study presented two experiments on Chinese handwriting performance (time, accuracy, the number of protruding strokes and number of rewritings) and subjective ratings (mental workload, satisfaction, and preference) on mobile devices. Experiment 1 evaluated the effects of size of the input box, input method and display size on Chinese handwriting performance and preference. It was indicated that the optimal input sizes were 30.8 × 30.8 mm, 46.6 × 46.6 mm, 58.9 × 58.9 mm and 84.6 × 84.6 mm for devices with 3.5-inch, 5.5-inch, 7.0-inch and 9.7-inch display sizes, respectively. Experiment 2 proved the significant effects of location of the input box, input method and display size on Chinese handwriting performance and subjective ratings. It was suggested that the optimal location was central regardless of display size and input method. Copyright © 2016 Elsevier Ltd. All rights reserved.

13 CFR 121.1001 - Who may initiate a size protest or request a formal size determination?

Code of Federal Regulations, 2010 CFR

2010-01-01

... which the headquarters of the protested offeror is located, regardless of the location of a parent company or affiliates, or the Director, Office of Government Contracting; and (iv) Other interested...

Waveguide coupling in the few-cycle regime

NASA Astrophysics Data System (ADS)

Leblond, Hervé; Terniche, Said

2016-04-01

We consider the coupling of two optical waveguides in the few-cycle regime. The analysis is performed in the frame of a generalized Kadomtsev-Petviashvili model. A set of two coupled modified Korteweg-de Vries equations is derived, and it is shown that three types of coupling can occur, involving the linear index, the dispersion, or the nonlinearity. The linear nondispersive coupling is investigated numerically, showing the formation of vector solitons. Separate pulses may be trapped together if they have not initially the same location, size, or phase, and even if their initial frequencies differ.

Field evaluation of ventilation system performance in enclosed parking garages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayari, A.M.; Grot, D.A.; Krarti, M.

2000-07-01

This paper summarizes the results of a field study to determine the ventilation requirements and the contaminant levels in existing enclosed parking garages. The testing was conducted in seven parking garages with different sizes, traffic flow patterns, vehicle types, and locations. In particular, the study compares the actual ventilation rates measured using the tracer gas technique with the ventilation requirements of ANSI/ASHRAE Standard 62-1989. In addition, the field test evaluated the effectiveness of the existing ventilation systems in maintaining acceptable contaminant levels within enclosed parking garages.

Performance of a High-Speed Compression-Ignition Engine Using Multiple Orifice Fuel Injection Nozzles

NASA Technical Reports Server (NTRS)

Spanogle, J A; Foster, H H

1930-01-01

This report presents test results obtained at the Langley Memorial Aeronautical Laboratory of the National Advisory Committee for Aeronautics during an investigation to determine the relative performance of a single-cylinder, high-speed, compression-ignition engine when using fuel injection valve nozzles with different numbers, sizes, and directions of round orifices. A spring-loaded, automatic injection valve was used, centrally located at the top of a vertical disk-type combustion chamber formed between horizontally opposed inlet and exhaust valves of a 5 inch by 7 inch engine.

Radiographic and ultrasonic characterization of sintered silicon carbide

NASA Technical Reports Server (NTRS)

Baaklini, G. Y.; Abel, P. B.

1988-01-01

The capabilities were investigated of projection microfocus X-radiography, ultrasonic velocity and attenuation, and reflection scanning acoustic microscopy for characterizing silicon carbide specimens. Silicon carbide batches covered a range of densities and different microstructural characteristics. Room temperature, four point flexural strength tests were conducted. Fractography was used to identify types, sizes, and locations of fracture origins. Fracture toughness values were calculated from fracture strength and flaw characterization data. Detection capabilities of radiography and acoustic microscopy for fracture-causing flaws were evaluated. Applicability of ultrasonics for verifying material strength and toughness was examined.

Flaw imaging and ultrasonic techniques for characterizing sintered silicon carbide

NASA Technical Reports Server (NTRS)

Baaklini, George Y.; Abel, Phillip B.

1987-01-01

The capabilities were investigated of projection microfocus x-radiography, ultrasonic velocity and attenuation, and reflection scanning acoustic microscopy for characterizing silicon carbide specimens. Silicon carbide batches covered a range of densities and different microstructural characteristics. Room temperature, four point flexural strength tests were conducted. Fractography was used to identify types, sizes, and locations of fracture origins. Fracture toughness values were calculated from fracture strength and flaw characterization data. Detection capabilities of radiography and acoustic microscopy for fracture-causing flaws were evaluated. Applicability of ultrasonics for verifying material strength and toughness was examined.

Satisfactory treatment of a large connective tissue nevus with intralesional steroid injection.

PubMed

Saki, Nasrin; Dorostkar, Azadeh; Heiran, Alireza; Aslani, Fatemeh Sari

2018-01-01

Collagenoma is a type of connective tissue nevi, a rare hamartomatous malformation characterized by the predominant proliferation of normal collagen fibers and normal, decreased, or increased elastic fibers. Collagenomas present as multiple or solitary, hereditary or sporadic, asymptomatic, skin-colored papules, nodules, and plaques with variable sizes, and are usually located on the trunk, arm, and back. Here, we report on a 14-year-old boy who presented with an isolated giant collagenoma of the frontal area that dramatically responded to intralesional triamcinolone acetonide.

Aerial ULV control of Aedes aegypti with naled (Dibrom) inside simulated rural village and urban cryptic habitats.

PubMed

Britch, Seth C; Linthicum, Kenneth J; Aldridge, Robert L; Breidenbaugh, Mark S; Latham, Mark D; Connelly, Peter H; Rush, Mattie J E; Remmers, Jennifer L; Kerce, Jerry D; Silcox, Charles A

2018-01-01

We conducted aerial fixed wing ultra low volume (ULV) spray trials with naled to investigate penetration of exposed and simulated cryptic habitat within opened buildings, partially sealed buildings, and outdoor locations targeting sentinel adult Aedes aegypti mosquitoes in north central Florida. Mortality was observed in open and closed buildings and outdoors, even in mosquitoes placed in cryptic habitats. Observations on the impact of building type, mosquito exposure method such as placement in cryptic habitat, and spray nozzle size on mosquito mortality are described and analyzed.

Survey of aircraft icing simulation test facilities in North America

NASA Technical Reports Server (NTRS)

Olsen, W.

1981-01-01

A survey was made of the aircraft icing simulation facilities in North America: there are 12 wind tunnels, 28 engine test facilities, 6 aircraft tankers and 14 low velocity facilities, that perform aircraft icing tests full or part time. The location and size of the facility, its speed and temperature range, icing cloud parameters, and the technical person to contact are surveyed. Results are presented in tabular form. The capabilities of each facility were estimated by its technical contact person. The adequacy of these facilities for various types of icing tests is discussed.

Size and location of defects at the coupling interface affect lithotripter performance.

PubMed

Li, Guangyan; Williams, James C; Pishchalnikov, Yuri A; Liu, Ziyue; McAteer, James A

2012-12-01

Study Type--Therapy (case series) Level of Evidence 4. What's known on the subject? and What does the study add? In shock wave lithotripsy air pockets tend to get caught between the therapy head of the lithotripter and the skin of the patient. Defects at the coupling interface hinder the transmission of shock wave energy into the body, reducing the effectiveness of treatment. This in vitro study shows that ineffective coupling not only blocks the transmission of acoustic pulses but also alters the properties of shock waves involved in the mechanisms of stone breakage, with the effect dependent on the size and location of defects at the coupling interface. • To determine how the size and location of coupling defects caught between the therapy head of a lithotripter and the skin of a surrogate patient (i.e. the acoustic window of a test chamber) affect the features of shock waves responsible for stone breakage. • Model defects were placed in the coupling gel between the therapy head of a Dornier Compact-S electromagnetic lithotripter (Dornier MedTech, Kennesaw, GA, USA) and the Mylar (biaxially oriented polyethylene terephthalate) (DuPont Teijin Films, Chester, VA, USA) window of a water-filled coupling test system. • A fibre-optic probe hydrophone was used to measure acoustic pressures and map the lateral dimensions of the focal zone of the lithotripter. • The effect of coupling conditions on stone breakage was assessed using gypsum model stones. • Stone breakage decreased in proportion to the area of the coupling defect; a centrally located defect blocking only 18% of the transmission area reduced stone breakage by an average of almost 30%. • The effect on stone breakage was greater for defects located on-axis and decreased as the defect was moved laterally; an 18% defect located near the periphery of the coupling window (2.0 cm off-axis) reduced stone breakage by only ~15% compared to when coupling was completely unobstructed. • Defects centred within the coupling window acted to narrow the focal width of the lithotripter; an 8.2% defect reduced the focal width ~30% compared to no obstruction (4.4 mm vs 6.5 mm). • Coupling defects located slightly off centre disrupted the symmetry of the acoustic field; an 18% defect positioned 1.0 cm off-axis shifted the focus of maximum positive pressure ~1.0 mm laterally. • Defects on and off-axis imposed a significant reduction in the energy density of shock waves across the focal zone. • In addition to blocking the transmission of shock-wave energy, coupling defects also disrupt the properties of shock waves that play a role in stone breakage, including the focal width of the lithotripter and the symmetry of the acoustic field • The effect is dependent on the size and location of defects, with defects near the centre of the coupling window having the greatest effect. • These data emphasize the importance of eliminating air pockets from the coupling interface, particularly defects located near the centre of the coupling window. © 2012 BJU INTERNATIONAL.

Geographic location and phylogeny are the main determinants of the size of the geographical range in aquatic beetles

PubMed Central

2011-01-01

Background Why some species are widespread while others are very restricted geographically is one of the most basic questions in biology, although it remains largely unanswered. This is particularly the case for groups of closely related species, which often display large differences in the size of the geographical range despite sharing many other factors due to their common phylogenetic inheritance. We used ten lineages of aquatic Coleoptera from the western Palearctic to test in a comparative framework a broad set of possible determinants of range size: species' age, differences in ecological tolerance, dispersal ability and geographic location. Results When all factors were combined in multiple regression models between 60-98% of the variance was explained by geographic location and phylogenetic signal. Maximum latitudinal and longitudinal limits were positively correlated with range size, with species at the most northern latitudes and eastern longitudes displaying the largest ranges. In lineages with lotic and lentic species, the lentic (better dispersers) display larger distributional ranges than the lotic species (worse dispersers). The size of the geographical range was also positively correlated with the extent of the biomes in which the species is found, but we did not find evidence of a clear relationship between range size and age of the species. Conclusions Our findings show that range size of a species is shaped by an interplay of geographic and ecological factors, with a phylogenetic component affecting both of them. The understanding of the factors that determine the size and geographical location of the distributional range of species is fundamental to the study of the origin and assemblage of the current biota. Our results show that for this purpose the most relevant data may be the phylogenetic history of the species and its geographical location. PMID:22122885

Determination of a temperature sensor location for monitoring weld pool size in GMAW

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boo, K.S.; Cho, H.S.

1994-11-01

This paper describes a method of determining the optimal sensor location to measure weldment surface temperature, which has a close correlation with weld pool size in the gas metal arc (GMA) welding process. Due to the inherent complexity and nonlinearity in the GMA welding process, the relationship between the weldment surface temperature and the weld pool size varies with the point of measurement. This necessitates an optimal selection of the measurement point to minimize the process nonlinearity effect in estimating the weld pool size from the measured temperature. To determine the optimal sensor location on the top surface of themore » weldment, the correlation between the measured temperature and the weld pool size is analyzed. The analysis is done by calculating the correlation function, which is based upon an analytical temperature distribution model. To validate the optimal sensor location, a series of GMA bead-on-plate welds are performed on a medium-carbon steel under various welding conditions. A comparison study is given in detail based upon the simulation and experimental results.« less

X-ray radiation detectors of ``scintillator-photoreceiving device type'' for industrial digital radiography with improved spatial resolution

NASA Astrophysics Data System (ADS)

Ryzhykov, V. D.; Lysetska, O. K.; Opolonin, O. D.; Kozin, D. N.

2003-06-01

Main types of photoreceivers used in X-ray digital radiography systems are luminescent screens that transfer the optical image onto charge collection instruments, which require cooling, and semiconductor silicon detectors, which limit the contrast sensitivity. We have developed and produced X-ray radiation detectors of "scintillator-photoreceiving device" (S-PRD) type, which are integrally located on the inverse side of the photodiode (PD). The receiving-converting circuit (RCC) is designed for data conversion into digital form and their input into PC. Software is provided for RCC control and image visualization. Main advantages of these detectors are high industrial resolution (3-5 line pairs per mm), detecting activity up to 20 μm, controlled sensitivity, low weight and small size, imaging low (0.1-0.3 mrad) object dose in real time. In this work, main characteristics of 32-, 64- and 1024-channel detectors of S-PRD type were studied and compared for X-ray sensitivity with S-PD detectors. Images of the tested objects have been obtained. Recommendations are given on the use of different scintillation materials, depending upon the purpose of a digital radiographic system. The detectors operate in a broad energy range of ionizing radiation, hence the size of the controlled object is not limited. The system is sufficiently powerful to ensure frontal (through two walls) observation of pipelines with wall thickness up to 10 cm.

Quantifying carbon footprint reduction opportunities for U.S. households and communities.

PubMed

Jones, Christopher M; Kammen, Daniel M

2011-05-01

Carbon management is of increasing interest to individuals, households, and communities. In order to effectively assess and manage their climate impacts, individuals need information on the financial and greenhouse gas benefits of effective mitigation opportunities. We use consumption-based life cycle accounting techniques to quantify the carbon footprints of typical U.S. households in 28 cities for 6 household sizes and 12 income brackets. The model includes emissions embodied in transportation, energy, water, waste, food, goods, and services. We further quantify greenhouse gas and financial savings from 13 potential mitigation actions across all household types. The model suggests that the size and composition of carbon footprints vary dramatically between geographic regions and within regions based on basic demographic characteristics. Despite these differences, large cash-positive carbon footprint reductions are evident across all household types and locations; however, realizing this potential may require tailoring policies and programs to different population segments with very different carbon footprint profiles. The results of this model have been incorporated into an open access online carbon footprint management tool designed to enable behavior change at the household level through personalized feedback.

Motor unit and muscle fiber type grouping after peripheral nerve injury in the rat.

PubMed

Gordon, Tessa; de Zepetnek, Joanne E Totosy

2016-11-01

Muscle unit (MU) fibers innervated by one motoneuron and corresponding muscle fiber types are normally distributed in a mosaic. We asked whether, 4-8months after common peroneal nerve transection and random surgical alignment of nerve stumps in rat tibialis anterior muscles 1) reinnervated MU muscle and muscle fiber type clumping is invariant and 2) slow and fast motoneurons regenerate their nerve fibers within original endoneurial pathways. MU contractile forces were recorded in vivo, the MUs classified into types according to their contractile speed and fatigability, and one MU subjected to alternate exhaustive stimulation-recovery cycles to deplete glycogen for histochemical MU fiber recognition and enumeration, and muscle fiber typing. MU muscle fibers occupied defined territories whose size increased with MU force and muscle fiber numbers in normal and reinnervated muscles. The reinnervated MU muscle fiber territories were significantly smaller, the fibers clumped within 1-3 groups in 90% of the MUs, and each fiber lying adjacent to another significantly more frequently. Most reinnervated slow muscle fibers were normally located in the deep muscle compartment but substantial numbers were located abnormally in the superficial compartment. Our findings that well reinnervated muscle fibers clump in small muscles contrast with our earlier findings of clumping in large muscles only when reinnervated MU numbers were significantly reduced. We conclude that fiber type clumping is predictive of muscle reinnervation in small but not large muscles. In the latter muscles, clumping is more indicative of sprouting after partial nerve injuries than of muscle reinnervation after complete nerve injuries. Copyright © 2016 Elsevier Inc. All rights reserved.

SU-F-J-119: Pilot Study On the Location-Based Lung Motion Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, TK; Ewald, A

2016-06-15

Purpose: In most of lung treatment cases with various radiotherapy beam modalities, 4DCT images are obtained in order to define ITV. ITV is defined with the signal from motion monitoring system, e.g. RPM. However, the signal is not consistent with tumor motion because it varies with location, its size, age, gender, etc. In the present study, the location-based motion assessment is presented. Methods: 4DCT images of 70 patients were reviewed: 28-left-lung and 42-right-lung patients; 36-female and 34-male patients; the age range of 51.2–89.9; tumor-size range of 0.75–9.50cm with 25% of these adherent to bony-anatomy. Philips Big-Bore Simulation CT and RPMmore » systems were used. The study was performed as follows. First, RPM signal and tumor motion in superior-inferior direction was compared. Second, the tumor size and its motion amplitude in all directions were measured at multiple locations. Third, the average tumor motion was calculated to assess general motion amplitudes at various locations. Results: RPM amplitude is not consistent with lung tumor motion amplitude. The tumors of similar sizes at similar location present various motion amplitude up to 1.1cm difference, but in average, the standard deviation was <0.5cm. Almost regardless of tumor sizes, the tumor motion was greatest at lower lobe location (>=1.0cm), and the smallest at upper lobe location and when adherent to bony-anatomy (<=0.5cm). Conclusion: The tumor size affects the motion amplitude less than does the tumor location. However, as the study results indicate that tumor motion has noticeable variation and so further study with more patient cases is needed. Also, for the same patient, the RPM signal presents instability of breathing, and clinically the patient with the instability of RPM breathing of <=10% is selected for respiratory-gated radiotherapy and ∼25% of patients under current study was treated. Patient-specific motion-uncertainty margins are considered to be added following further study.« less

[Influencing factors of reproduction status of patients undergoing laparoscopic myomectomy].

PubMed

Song, Guang-hui; Zhang, Song-ying; Li, Bai-jia; Wei, Wei; Huang, Dong; Lin, Xiao-na; Lou, Hong-ying

2013-09-17

To explore the influencing factors of reproduction status in women undergoing laparoscopic myomectomy (LM). A total of 278 LM patients were recruited.We retrospectively reviewed the reproduction status of 87 pregnant cases after LM. The correlations of their pregnancy outcomes and such clinical profiles as age, operative techniques, biological characteristics of fibroids (number, type, size and location) were analyzed.No uterine rupture occurred during the gestation period. None of them switched to open surgery due to laparoscopic difficulties. However, one patient had a laparoscopic suture for secondary bleeding of uterine incision. At 3 months post-operation, sonography showed no heterogeneous echo, effusion and hematoma in uterine incision.Incision through uterine cavity occurred intraoperatively in 8 cases, but no intrauterine adhesion was found on hysteroscopy 3 months later. And 87 women became pregnant and the postoperative fertilization time was from 2 months to 5 years. Age influenced the postoperative pregnancy rate.Other factors such as location, number and size of fibroid had no impact on fertility. For achieving a high conception rate and guaranteeing the safety of pregnant women, a clinician should select reasonable surgical approaches, perform accurate anatomical restoration, apply strict hemostasis and choose a right time of conception.

Network analysis of a regional fishery: Implications for management of natural resources, and recruitment and retention of anglers

USGS Publications Warehouse

Martin, Dustin R.; Shizuka, Daizaburo; Chizinski, Christopher J.; Pope, Kevin L.

2017-01-01

Angler groups and water-body types interact to create a complex social-ecological system. Network analysis could inform detailed mechanistic models on, and provide managers better information about, basic patterns of fishing activity. Differences in behavior and reservoir selection among angler groups in a regional fishery, the Salt Valley fishery in southeastern Nebraska, USA, were assessed using a combination of cluster and network analyses. The four angler groups assessed ranged from less active, unskilled anglers (group One) to highly active, very skilled anglers (group Four). Reservoir use patterns and the resulting network communities of these four angler groups differed; the number of reservoir communities for these groups ranged from two to three and appeared to be driven by reservoir location (group One), reservoir size and its associated attributes (groups Two and Four), or an interaction between reservoir size and location (group Three). Network analysis is a useful tool to describe differences in participation among angler groups within a regional fishery, and provides new insights about possible recruitment of anglers. For example, group One anglers fished reservoirs closer to home and had a greater probability of dropping out if local reservoir access were restricted.

First LOCSMITH locations of deep moonquakes

NASA Astrophysics Data System (ADS)

Hempel, S.; Knapmeyer, M.; Sens-Schönfelder, C.; Oberst, J.

2008-09-01

Introduction Several thousand seismic events were recorded by the Apollo seismic network from 19691977. Different types of events can be distinguished: meteoroid impacts, thermal quakes and internally caused moonquakes. The latter subdivide into shallow (100 to 300km) and deep moonquakes (700 to 1100km), which are by far the most common events. The deep quakes would be no immediate danger to inhabitated stations on the Earth's Moon because of their relatively low magnitude and great depth. However, they bear important information on lunar structure and evolution, and their distribution probably reflects their source mechanism. In this study, we reinvestigate location patterns of deep lunar quakes. LOCSMITH The core of this study is a new location method (LOCSMITH, [1]). This algorithm uses time intervals rather than time instants as input, which contain the dedicated arrival with probability 1. LOCSMITH models and compares theoretical and actual travel times on a global scale and uses an adaptive grid to search source locations compatible with all observations. The output is a set of all possible hypocenters for the considered region of repeating, tidally triggered moonquake activity, called clusters. The shape and size of these sets gives a better estimate of the location uncertainty than the formal standard deviations returned by classical methods. This is used for grading of deep moonquake clusters according to the currently available data quality. Classification of deep moonquakes As first step, we establish a reciprocal dependence of size and shape of LOCSMITH location clouds on number of arrivals. Four different shapes are recognized, listed here in an order corresponding to decreasing spatial resolution: 1. "Balls", which are well defined and relatively small types of sets resembling the commonly assumed error ellipsoid. These are found in the best cases with many observations. Locations in this shape are obtained for clusters 1, 18 or 33, these were already well located by earlier works [2,3]. 2. The next best shape of a location set is the "banana" as found for clusters 5, 39 or 53 [Fig. 1]. In this case, only limited depth resolution is available, and the solution spreads over a large volume. The size of a "banana" could be minimized by either finding a not yet discovered shear wave arrival or estimating a S arrival time interval by considering the coda instead of a clear S arrival. 3. Shape of clouds we call "cones" are formed by clusters for which no compressional wave arrivals, but three S arrivals were picked. Such solutions were found for clusters 35, 201 or 218 [Fig. 2]. A depth limitation is given only by the surface of the Moon's far side. In previous works, locations of these clusters were usually determined with a fixed depth, thus neglecting all depth uncertainty [2]. 4. The fourth and worst class shows a "disc"like shape with no depth resolution and almost no latitude resolution. Clusters of this class, like 4, 23 or 43, were not located so far. From class 1 ("ball") to 4 ("disc") the amount of possible hypocenters increases. So we also found a correlation between size and shape of volumes containing possible hypocenter solutions. Aim We classified all clusters according to the solution set scheme by using arrival times of [2] with an estimated error of ±10s as input for LOCSMITH. We reprocess selected clusters of each class to come up with the special requirements and possibilities of this new location method. As said above, one of the requirements of LOCSMITH is the definition of a time interval instead of a time instant for input, and an interesting option is using an estimated S arrival time interval derived from coda and scattering model, lacking a clear S arrival. We try to find fully automated methods for each processing step, dependent on the quality of data. Methods For despiking we merged methods by [4] and [5] and achieve very good results even for worst case as already presented in [6]. Prior to stacking we developed a complex multiparameter correlation algorithm to calculate the optimum time shift. Results We present relocations of selected deep moonquakes in context of data availability and quality. Previous locations are often contained in our location clouds, but realistic location uncertainties allow large deviations from the best fitting solutions, including locations on the far side of the Moon. Perspective By developing new methods for data processing and using the LOCSMITH locating algorithm we hope to reduce the location uncertainty sufficiently to make sure that all sources are on the near side, or to prove a far side origin of some of them. This would answer questions of hemispheric symmetry of lunar deep seismicity and the Moon's internal structure. References [1] Knapmeyer (2008) accepted to GJI. [2] Nakamura (2005) JGR, 110, E01001. [3] Lognonné (2003) EPSL, 211, 2744. [4] Bulow (2005) JGR, 110, E10003. [5] Sonnemann (2005) EGU05A07960. [6] Hempel, Knapmeyer, Oberst (2008) EGU2008A07989.

Magnetic Resonance Imaging (MRI) Analysis of Fibroid Location in Women Achieving Pregnancy After Uterine Artery Embolization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, Woodruff J.; Bratby, Mark John

The purpose of this study was to evaluate the fibroid morphology in a cohort of women achieving pregnancy following treatment with uterine artery embolization (UAE) for symptomatic uterine fibroids. A retrospective review of magnetic resonance imaging (MRI) of the uterus was performed to assess pre-embolization fibroid morphology. Data were collected on fibroid size, type, and number and included analysis of follow-up imaging to assess response. There have been 67 pregnancies in 51 women, with 40 live births. Intramural fibroids were seen in 62.7% of the women (32/48). Of these the fibroids were multiple in 16. A further 12 women hadmore » submucosal fibroids, with equal numbers of types 1 and 2. Two of these women had coexistent intramural fibroids. In six women the fibroids could not be individually delineated and formed a complex mass. All subtypes of fibroid were represented in those subgroups of women achieving a live birth versus those who did not. These results demonstrate that the location of uterine fibroids did not adversely affect subsequent pregnancy in the patient population investigated. Although this is only a small qualitative study, it does suggest that all types of fibroids treated with UAE have the potential for future fertility.« less

Comparison of Diagnostic Accuracy between Octopus 900 and Goldmann Kinetic Visual Fields

PubMed Central

Rowe, Fiona J.; Rowlands, Alison

2014-01-01

Purpose. To determine diagnostic accuracy of kinetic visual field assessment by Octopus 900 perimetry compared with Goldmann perimetry. Methods. Prospective cross section evaluation of 40 control subjects with full visual fields and 50 patients with known visual field loss. Comparison of test duration and area measurement of isopters for Octopus 3, 5, and 10°/sec stimulus speeds. Comparison of test duration and type of visual field classification for Octopus versus Goldmann perimetry. Results were independently graded for presence/absence of field defect and for type and location of defect. Statistical evaluation comprised of ANOVA and paired t test for evaluation of parametric data with Bonferroni adjustment. Bland Altman and Kappa tests were used for measurement of agreement between data. Results. Octopus 5°/sec perimetry had comparable test duration to Goldmann perimetry. Octopus perimetry reliably detected type and location of visual field loss with visual fields matched to Goldmann results in 88.8% of results (K = 0.775). Conclusions. Kinetic perimetry requires individual tailoring to ensure accuracy. Octopus perimetry was reproducible for presence/absence of visual field defect. Our screening protocol when using Octopus perimetry is 5°/sec for determining boundaries of peripheral isopters and 3°/sec for blind spot mapping with further evaluation of area of field loss for defect depth and size. PMID:24587983

SU-E-T-517: Investigation of Factors Contributing to Extracranial Radiation Doses From Leksell Gamma Knife

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kon, D; Kameda Medical Centre, Chiba, JP; Nakano, M

2015-06-15

Purpose The purpose of this study is to investigate dominant factors for doses to extracranial sites in treatment with Leksell Gamma Knife (LGK). Methods Monte Carlo simulation was implemented using EGS5 version 1.4.401. The simulation was divided into two major steps for the purpose of efficiency. As the first step, phase-space files were obtained at a scoring plane located just below patient-side surface of the collimator helmet of LGK. Scored particles were classified into three groups, primary, leakage and scatter, using their history information until their arrival to the scoring plane. Then classification was used at the following second stepmore » simulation to investigate which type of particle is dominant in the deposited energy at extra-cranial sites. In the second stage, a cylindrical phantom with a semisphere shaped head was modeled such that the geometrical center of the phantom’s head corresponds to the unit center point (UCP) of LGK. Scoring regions were arranged at 10 cm intervals from the UCP to 70 cm away on the central axis of the phantom. Energy deposition from each type of particles and location of interaction were recorded. Results The dominant factor of deposited energy depended on the collimator size. In the case of smaller collimator size, leakage was dominant. However, contribution of leakage was relatively small in the case of larger collimator size. The contribution of internal scatter varied with the distance from the UCP. In the proximal areas, internal scatter was dominant, whereas in the distal areas, particles interacting with machine components became dominant factor. Conclusion The Result of this study indicates that the dominant factor to dose to an extracranial site can vary with the distance from UCP and with collimator size. This means that the variation of this contribution must be considered for modeling of the extracranial dose especially in the distal area. This work was partly supported by the JSPS Core-to-Core Program (No. 23003)« less

An impedance-based approach for detection and quantification of damage in cracked plates and loose bolts in bridge structures

NASA Astrophysics Data System (ADS)

Rabiei, Masoud; Sheldon, Jeremy; Palmer, Carl

2012-04-01

The applicability of Electro-Mechanical Impedance (EMI) approach to damage detection, localization and quantification in a mobile bridge structure is investigated in this paper. The developments in this paper focus on assessing the health of Armored Vehicle Launched Bridges (AVLBs). Specifically, two key failure mechanisms of the AVLB to be monitored were fatigue crack growth and damaged (loose) rivets (bolts) were identified. It was shown through experiment that bolt damage (defined here as different torque levels applied to bolts) can be detected, quantified and located using a network of lead zirconate titanate (PZT) transducers distributed on the structure. It was also shown that cracks of various sizes can be detected and quantified using the EMI approach. The experiments were performed on smaller laboratory specimens as well as full size bridge-like components that were built as part of this research. The effects of various parameters such as transducer type and size on the performance of the proposed health assessment approach were also investigated.

Interaction of fine sediment with alluvial streambeds

USGS Publications Warehouse

Jobson, Harvey E.; Carey, William P.

1989-01-01

More knowledge is needed about the physical processes that control the transport of fine sediment moving over an alluvial bed. The knowledge is needed to design rational sampling and monitoring programs that assess the transport and fate of toxic substances in surface waters because the toxics are often associated with silt- and clay-sized particles. This technical note reviews some of the past research in areas that may contribute to an increased understanding of the processes involved. An alluvial streambed can have a large capacity to store fine sediments that are extracted from the flow when instream concentrations are high and it can gradually release fine sediment to the flow when the instream concentrations are low. Several types of storage mechanisms are available depending on the relative size distribution of the suspended load and bed material, as well as the flow hydraulics. Alluvial flow tends to segregate the deposited material according to size and density. Some of the storage locations are temporary, but some can store the fine sediment for very long periods of time.

Size and Velocity Characteristics of Droplets Generated by Thin Steel Slab Continuous Casting Secondary Cooling Air-Mist Nozzles

NASA Astrophysics Data System (ADS)

Minchaca M, J. I.; Castillejos E, A. H.; Acosta G, F. A.

2011-06-01

Direct spray impingement of high temperature surfaces, 1473 K to 973 K (1200 °C to 700 °C), plays a critical role in the secondary cooling of continuously cast thin steel slabs. It is known that the spray parameters affecting the local heat flux are the water impact flux w as well as the droplet velocity and size. However, few works have been done to characterize the last two parameters in the case of dense mists ( i.e., mists with w in the range of 2 to 90 L/m2s). This makes it difficult to rationalize how the nozzle type and its operating conditions must be selected to control the cooling process. In the present study, particle/droplet image analysis was used to determine the droplet size and velocity distributions simultaneously at various locations along the major axis of the mist cross section at a distance where the steel strand would stand. The measurements were carried out at room temperature for two standard commercial air-assisted nozzles of fan-discharge type operating over a broad range of conditions of practical interest. To achieve statistically meaningful samples, at least 6000 drops were analyzed at each location. Measuring the droplet size revealed that the number and volume frequency distributions were fitted satisfactorily by the respective log-normal and Nukiyama-Tanasawa distributions. The correlation of the parameters of the distribution functions with the water- and air-nozzle pressures allowed for reasonable estimation of the mean values of the size of the droplets generated. The ensemble of measurements across the mist axis showed that the relationship between the droplet velocity and the diameter exhibited a weak positive correlation. Additionally, increasing the water flow rate at constant air pressure caused a decrease in the proportion of the water volume made of finer droplets, whereas the volume proportion of faster droplets augmented until the water flow reached a certain value, after which it decreased. Diminishing the air-to-water flow rates ratio, particularly below 10, resulted in mists of bigger and slower droplets with low impinging Weber numbers. However, increasing the air pressure maintaining a constant water flow rate caused a greater proportion of finer and faster drops with Weber numbers greater than 80, which suggests an increased probability of wet drop contact with a hot surface that would intensify heat extraction.

Measure Guideline: Transitioning to a Tankless Water Heater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brozyna, K.; Rapport, A.

2012-09-01

This Measure Guideline provides information to help residential builders and retrofitters with the design, specification, selection, implementation, installation, and maintenance issues of transitioning from tank-type water heaters to tankless water heaters. The report compares the differences between tankless and tank-type water heaters, highlighting the energy savings that can be realized by adopting tankless water heaters over tank-type water heaters. Selection criteria and risks discussed include unit sizing and location, water distribution system, plumbing line length and diameter, water quality, electrical backup, and code issues. Cost and performance data are provided for various types of tankless and tank-type water heaters, bothmore » natural gas fired and electric. Also considered are interactions between the tankless water heater and other functional elements of a house, such as cold water supply and low-flow devices. Operating costs and energy use of water distribution systems for single- and two-story houses are provided, along with discussion of the various types of distribution systems that can be used with tankless water heaters. Finally, details to prepare for proper installation of a tankless water heater are described.« less

Network Structure as a Modulator of Disturbance Impacts in Streams

NASA Astrophysics Data System (ADS)

Warner, S.; Tullos, D. D.

2017-12-01

This study examines how river network structure affects the propagation of geomorphic and anthropogenic disturbances through streams. Geomorphic processes such as debris flows can alter channel morphology and modify habitat for aquatic biota. Anthropogenic disturbances such as road construction can interact with the geomorphology and hydrology of forested watersheds to change sediment and water inputs to streams. It was hypothesized that the network structure of streams within forested watersheds would influence the location and magnitude of the impacts of debris flows and road construction on sediment size and channel width. Longitudinal surveys were conducted every 50 meters for 11 kilometers of third-to-fifth order streams in the H.J. Andrews Experimental Forest in the Western Cascade Range of Oregon. Particle counts and channel geometry measurements were collected to characterize the geomorphic impacts of road crossings and debris flows as disturbances. Sediment size distributions and width measurements were plotted against the distance of survey locations through the network to identify variations in longitudinal trends of channel characteristics. Thresholds for the background variation in sediment size and channel width, based on the standard deviations of sample points, were developed for sampled stream segments characterized by location as well as geomorphic and land use history. Survey locations were classified as "disturbed" when they deviated beyond the reference thresholds in expected sediment sizes and channel widths, as well as flow-connected proximity to debris flows and road crossings. River network structure was quantified by drainage density and centrality of nodes upstream of survey locations. Drainage density and node centrality were compared between survey locations with similar channel characteristic classifications. Cluster analysis was used to assess the significance of survey location, proximity of survey location to debris flows and road crossings, drainage density and node centrality in predicting sediment size and channel width classifications for locations within the watershed. Results contribute to the understanding of susceptibility and responses of streams supporting critical habitat for aquatic species to debris flows and forest road disturbances.

Grand canonical Monte Carlo simulation of the adsorption isotherms of water molecules on model soot particles

NASA Astrophysics Data System (ADS)

Moulin, F.; Picaud, S.; Hoang, P. N. M.; Jedlovszky, P.

2007-10-01

The grand canonical Monte Carlo method is used to simulate the adsorption isotherms of water molecules on different types of model soot particles. The soot particles are modeled by graphite-type layers arranged in an onionlike structure that contains randomly distributed hydrophilic sites, such as OH and COOH groups. The calculated water adsorption isotherm at 298K exhibits different characteristic shapes depending both on the type and the location of the hydrophilic sites and also on the size of the pores inside the soot particle. The different shapes of the adsorption isotherms result from different ways of water aggregation in or/and around the soot particle. The present results show the very weak influence of the OH sites on the water adsorption process when compared to the COOH sites. The results of these simulations can help in interpreting the experimental isotherms of water adsorbed on aircraft soot.

Role of small oligomers on the amyloidogenic aggregation free-energy landscape.

PubMed

He, Xianglan; Giurleo, Jason T; Talaga, David S

2010-01-08

We combine atomic-force-microscopy particle-size-distribution measurements with earlier measurements on 1-anilino-8-naphthalene sulfonate, thioflavin T, and dynamic light scattering to develop a quantitative kinetic model for the aggregation of beta-lactoglobulin into amyloid. We directly compare our simulations to the population distributions provided by dynamic light scattering and atomic force microscopy. We combine species in the simulation according to structural type for comparison with fluorescence fingerprint results. The kinetic model of amyloidogenesis leads to an aggregation free-energy landscape. We define the roles of and propose a classification scheme for different oligomeric species based on their location in the aggregation free-energy landscape. We relate the different types of oligomers to the amyloid cascade hypothesis and the toxic oligomer hypothesis for amyloid-related diseases. We discuss existing kinetic mechanisms in terms of the different types of oligomers. We provide a possible resolution to the toxic oligomer-amyloid coincidence.

On the choice of statistical models for estimating occurrence and extinction from animal surveys

USGS Publications Warehouse

Dorazio, R.M.

2007-01-01

In surveys of natural animal populations the number of animals that are present and available to be detected at a sample location is often low, resulting in few or no detections. Low detection frequencies are especially common in surveys of imperiled species; however, the choice of sampling method and protocol also may influence the size of the population that is vulnerable to detection. In these circumstances, probabilities of animal occurrence and extinction will generally be estimated more accurately if the models used in data analysis account for differences in abundance among sample locations and for the dependence between site-specific abundance and detection. Simulation experiments are used to illustrate conditions wherein these types of models can be expected to outperform alternative estimators of population site occupancy and extinction. ?? 2007 by the Ecological Society of America.

Morphology and histology of the alimentary canal of Lygus hesperus (Heteroptera: Cimicomoropha: Miridae)

USGS Publications Warehouse

Habibi, J.; Coudron, T.A.; Backus, E.A.; Brandt, S.L.; Wagner, R.M.; Wright, M.K.; Huesing, J.E.

2008-01-01

Microdissection and transverse semithin sections were used to perform a light microscopy survey of the gross morphology and cellular anatomy of the alimentary canal, respectively, of Lygus hesperus Knight, a key pest of cotton (Gossypium hirsutum L.), alfalfa (Medicago sativa L.), and other crops. The gross morphology of the alimentary canal showed a relatively unadorned tube compared with other hemipterans, with variably shaped compartments and one small diverticulum. However, the epithelial cell anatomy of the gut was relatively complex, with the midgut having the most diverse structure and cell types. The midgut was typical of the "Lygus-type gut" seen in the older literature, i.e., it consisted of three major regions, the first (descending), second (ascending), and third (descending) ventriculi, with different variants of three major epithelial cell types in each region. Our light microscopy (LM) study suggests that the three cell types are nondifferentiated regenerative cells (which sparsely occurred throughout the midgut but were abundant in the anterior region of the first ventriculus), endocrine cells, and columnar cells. Although the Lygus gut cells strongly resemble those cell types seen in other insects, their identification should be confirmed via transmission electron microscopy to be considered definitive. These cell types differed in the size and opacity of vesicles, geometry of cell surface in the gut lumen, and size, shape, and concentration of brush-border microvilli and location within the gut. Comparison of gut structure in L. hesperus with that of other hemipterans, especially in relation to hemipteran phylogeny and feeding strategies, is discussed.

Two Sizes of Ripples on Surface of Martian Sand Dune

NASA Image and Video Library

2016-06-30

Two sizes of wind-sculpted ripples are evident in this view of the top surface of a Martian sand dune. Sand dunes and the smaller type of ripples also exist on Earth. The larger ripples -- roughly 10 feet (3 meters) apart -- are a type not seen on Earth nor previously recognized as a distinct type on Mars. The Mast Camera (Mastcam) on NASA's Curiosity Mars rover took the multiple component images of this scene on Dec. 13, 2015, during the 1,192nd Martian day, or sol, of the rover's work on Mars. That month, Curiosity was conducting the first close-up investigation ever made of active sand dunes anywhere other than Earth. The larger ripples have distinctive sinuous crest lines, compared to the smaller ripples. The location is part of "Namib Dune" in the Bagnold Dune Field, which forms a dark band along the northwestern flank of Mount Sharp. The component images were taken in early morning at this site, with the camera looking in the direction of the sun. This mosaic combining the images has been processed to brighten it and make the ripples more visible. The sand is very dark, both from the morning shadows and from the intrinsic darkness of the minerals that dominate its composition. http://photojournal.jpl.nasa.gov/catalog/PIA20755

Transport of Zinc Oxide Nanoparticles in a Simulated Gastric Environment

NASA Astrophysics Data System (ADS)

Mayfield, Ryan T.

Recent years have seen a growing interest in the use of many types of nano sized materials in the consumer sector. Potential uses include encapsulation of nutrients, providing antimicrobial activity, altering texture, or changing bioavailability of nutrients. Engineered nanoparticles (ENP) possess properties that are different than larger particles made of the same constituents. Properties such as solubility, aggregation state, and toxicity can all be changed as a function of size. The gastric environment is an important area for study of engineered nanoparticles because of the varied physical, chemical, and enzymatic processes that are prevalent there. These all have the potential to alter those properties of ENP that make them different from their bulk counterparts. The Human Gastric Simulator (HGS) is an advanced in vitro model that can be used to study many facets of digestion. The HGS consists of a plastic lining that acts as the stomach cavity with two sets of U-shaped arms on belts that provide the physical forces needed to replicate peristalsis. Altering the position of the arms or changing the speed of the motor which powers them allows one to tightly hone and replicate varied digestive conditions. Gastric juice, consisting of salts, enzymes, and acid levels which replicate physiological conditions, is introduced to the cavity at a controllable rate. The release of digested food from the lumen of simulated stomach is controlled by a peristaltic pump. The goal of the HGS is to accurately and repeatedly simulate human digestion. This study focused on introducing foods spiked with zinc oxide ENP and bulk zinc oxide into the HGS and then monitoring how the concentration of each changed at two locations in the HGS over a two hour period. The two locations chosen were the highest point in the lumen of the stomach, which represented the fundus, and a point just beyond the equivalent of the pylorus, which represented the antrum of the stomach. These points were chosen in order to elucidate if and how two different particle sizes of the same material are transported during digestion. Results showed that particles preferentially collected at Location A; time played a minor role in the separation to the two locations while particle size did not play any role.

Relationship of Tear Size and Location to Fatty Degeneration of the Rotator Cuff

PubMed Central

Kim, H. Mike; Dahiya, Nirvikar; Teefey, Sharlene A.; Keener, Jay D.; Galatz, Leesa M.; Yamaguchi, Ken

2010-01-01

Background: Fatty degeneration of the rotator cuff muscles may have detrimental effects on both anatomical and functional outcomes following shoulder surgery. The purpose of this study was to investigate the relationship between tear geometry and muscle fatty degeneration in shoulders with a deficient rotator cuff. Methods: Ultrasonograms of both shoulders of 262 patients were reviewed to assess the type of rotator cuff tear and fatty degeneration in the supraspinatus and infraspinatus muscles. The 251 shoulders with a full-thickness tear underwent further evaluation for tear size and location. The relationship of tear size and location to fatty degeneration of the supraspinatus and infraspinatus muscles was investigated with use of statistical comparisons and regression models. Results: Fatty degeneration was found almost exclusively in shoulders with a full-thickness rotator cuff tear. Of the 251 shoulders with a full-thickness tear, eighty-seven (34.7%) had fatty degeneration in either the supraspinatus or infraspinatus, or both. Eighty-two (32.7%) of the 251 full-thickness tears had a distance of 0 mm between the biceps tendon and anterior margin of the tear. Ninety percent of the full-thickness tears with fatty degeneration in both muscles had a distance of 0 mm posterior from the biceps, whereas only 9% of those without fatty degeneration had a distance of 0 mm. Tears with fatty degeneration had significantly greater width and length than those without fatty degeneration (p < 0.0001). Tears with fatty degeneration had a significantly shorter distance posterior from the biceps than those without fatty degeneration (p < 0.0001). The distance posterior from the biceps was found to be the most important predictor for supraspinatus fatty degeneration, whereas tear width and length were found to be the most important predictors for infraspinatus fatty degeneration. Conclusions: Fatty degeneration of the rotator cuff muscles is closely associated with tear size and location. The finding of this study suggests that the integrity of the anterior supraspinatus tendon is important to the development of fatty degeneration. Patients with full-thickness tears that extend through this area may benefit from earlier surgical intervention if fatty degeneration has not already occurred. Additionally, the findings suggest the importance of secure fixation and healing of the anterior aspect of the supraspinatus with surgical repair. PMID:20360505

A study of oral contrast coating on the surface of polyps: an implication for computer-aided detection and classification of polyps

NASA Astrophysics Data System (ADS)

Singh, Harmanpreet; Li, Lihong C.; Pomeroy, Marc; Pickhardt, Perry J.; Barish, Matthew A.; Harrington, Donald P.; Liang, Zhengrong

2017-03-01

Accurate identification of polyps is the ultimate goal of Computed Tomography Colonography (CTC). While oral contrast agents were originally used to tag stool and fluid for the ultimate goal of CTC, recently their effect on coating the surface of polyps has been observed. This study aims to evaluate (1) the frequency at which the oral contrast adhered to polyp surfaces and (2) if there was a difference in contrast adherence with respect to diverse polyp types. To eliminate gravity as a factor in this study, the polyps in contact with tagged fluid pools, particularly on the bottom of the colon wall were excluded. A total of 150 polyps were selected under the above condition from a CTC database and screened for any adherent contrast on the luminal edge. Among the total, 53% of the screened polyps had adherent contrast. Serrated adenomas and hyperplastic polyps had a higher tagging percentage, 77.80% and 62.50% respectively, than tubular adenomas and tubulovillous adenomas, 44.40% and 43% respectively. Other factors that were analyzed for the effect on coating include size and location of the polyps. The higher tagging percentage of serrated adenomas and hyperplastic polyps may be due to their similar cellular features. The average size of the polyps was 8.9 mm. When the polyps were separated by size into small (5-9mm) and large (10-26mm) groups, the large group had a higher tagging percentage. The polyp types were also classified by location with the major findings being: 1) Tubular adenomas were present in all segments of the colon and 2) that serrated adenomas were present at a higher percentage in the proximal colon. These findings shall facilitate characterizing tagging agents and improve computer aided detection and classification of polyps via CTC.

Metallicity Variations in the Type II Globular Cluster NGC 6934

NASA Astrophysics Data System (ADS)

Marino, A. F.; Yong, D.; Milone, A. P.; Piotto, G.; Lundquist, M.; Bedin, L. R.; Chené, A.-N.; Da Costa, G.; Asplund, M.; Jerjen, H.

2018-06-01

The Hubble Space Telescope photometric survey of Galactic globular clusters (GCs) has revealed a peculiar “chromosome map” for NGC 6934. In addition to a typical sequence, similar to that observed in Type I GCs, NGC 6934 displays additional stars on the red side, analogous to the anomalous Type II GCs, as defined in our previous work. We present a chemical abundance analysis of four red giants in this GC. Two stars are located on the chromosome map sequence common to all GCs, and another two lie on the additional sequence. We find (i) star-to-star Fe variations, with the two anomalous stars being enriched by ∼0.2 dex. Because of our small-size sample, this difference is at the ∼2.5σ level. (ii) There is no evidence for variations in the slow neutron-capture abundances over Fe, at odds with what is often observed in anomalous Type II GCs, e.g., M 22 and ω Centauri (iii) no large variations in light elements C, O, and Na, compatible with locations of the targets on the lower part of the chromosome map where such variations are not expected. Since the analyzed stars are homogeneous in light elements, the only way to reproduce the photometric splits on the sub-giant (SGB) and the red giant (RGB) branches is to assume that red RGB/faint SGB stars are enhanced in [Fe/H] by ∼0.2. This fact corroborates the spectroscopic evidence of a metallicity variation in NGC 6934. The observed chemical pattern resembles only partially the other Type II GCs, suggesting that NGC 6934 might belong either to a third class of GCs, or be a link between normal Type I and anomalous Type II GCs. Based on observations with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by AURA, Inc., under NASA contract NAS 5-26555. This paper includes data gathered with the 6.5 m Magellan Telescopes located at Las Campanas Observatory, Chile, and Gemini Telescope at Canada–France–Hawaii Telescope.

Impact of land use change on soil organic matter dynamics in subalpine grassland

NASA Astrophysics Data System (ADS)

Meyer, Stefanie; Leifeld, Jens; Bahn, Michael; Fuhrer, Jürg

2010-05-01

Information regarding the response of soil organic matter (SOM) in soils to past and expected future land use changes in the European Alps is scarce. Understanding this response requires knowledge of size and residence times of SOM fractions with distinct stabilities. In order to quantify differences between types of land use in the amount, distribution and turnover rates of soil organic carbon (SOC) in subalpine grassland soils, we used soil aggregate and SOM density fractionation in combination with 14C dating. Samples were taken along gradients of different types of land use from meadow (M) to pasture (P) and to abandoned grassland (A) in the Stubai Valley and in the Matsch Valley. Sampling sites in both areas were located at equal altitude (1880 m and 1820 m, respectively) with the same parent material and soil type, but the Matsch Valley receives 400-500 mm less annual rainfall. SOC stocks in the top 10 cm were 2.47 ± 0.32 (M), 2.75 ± 0.32 (P), and 2.50 ± 0.31 kg C/m2 (A) in the Stubai Valley and 2.25 ± 0.14 (M), 3.45 ± 0.22 (P), 3.16 ± 0.27 kg C/m2(A) in the Matsch Valley. Three aggregate size classes were separated by wet sieving: 2 mm. The light floating fraction (wPOM, ρ >1 g/cm3) was included in the analysis. Free (f-) and occluded particulate organic matter (oPOM) were isolated from each aggregate size class (ρ >1.6 g/cm3). At both locations, more than 80% of SOC was stored in small (0.25-2 mm) and large (>2 mm) macroaggregates, but no trend in relation to the different types of land use could be detected. The fraction of C in fPOM and in oPOM in all aggregate size classes was highest for soil from abandoned grasslands. The bulk soil of the abandoned site in the Stubai Valley showed a significantly higher share of fPOM-C and oPOM-C and a higher amount of wPOM-C as compared to the soil from managed grassland, whereas in the Matsch Valley pasture soil had a significantly higher wPOM-C content. At both sites, 13C natural abundance analyses revealed a gradient in 13C between density fractions. wPOM was particularly useful to reveal differences between sampling sites. Radiocarbon values emphasized the importance of this fraction for the calculation of the turnover of bulk soil C. wPOM turned out to be the most active fraction turning over in 2-4 years. Bulk SOC turnover time was approximately 46 years for pasture soil and 78 years for meadow soil. In conclusion, density fractionation produced homogenous fractions allowing detection of differences between different land use types. However, C distribution among aggregates did not systematically differ.

The effect of the sample size and location on contrast ultrasound measurement of perfusion parameters.

PubMed

Leinonen, Merja R; Raekallio, Marja R; Vainio, Outi M; Ruohoniemi, Mirja O; O'Brien, Robert T

2011-01-01

Contrast-enhanced ultrasound can be used to quantify tissue perfusion based on region of interest (ROI) analysis. The effect of the location and size of the ROI on the obtained perfusion parameters has been described in phantom, ex vivo and in vivo studies. We assessed the effects of location and size of the ROI on perfusion parameters in the renal cortex of 10 healthy, anesthetized cats using Definity contrast-enhanced ultrasound to estimate the importance of the ROI on quantification of tissue perfusion with contrast-enhanced ultrasound. Three separate sets of ROIs were placed in the renal cortex, varying in location, size or depth. There was a significant inverse association between increased depth or increased size of the ROI and peak intensity (P < 0.05). There was no statistically significant difference in the peak intensity between the ROIs placed in a row in the near field cortex. There was no significant difference in the ROIs with regard to arrival time, time to peak intensity and wash-in rate. When comparing two different ROIs in a patient with focal lesions, such as suspected neoplasia or infarction, the ROIs should always be placed at same depth and be as similar in size as possible.

Hayabusa2 Sampler: Collection of Asteroidal Surface Material

NASA Astrophysics Data System (ADS)

Sawada, Hirotaka; Okazaki, Ryuji; Tachibana, Shogo; Sakamoto, Kanako; Takano, Yoshinori; Okamoto, Chisato; Yano, Hajime; Miura, Yayoi; Abe, Masanao; Hasegawa, Sunao; Noguchi, Takaaki

2017-07-01

Japan Aerospace Exploration Agency (JAXA) launched the asteroid exploration probe "Hayabusa2" in December 3rd, 2014, following the 1st Hayabusa mission. With technological and scientific improvements from the Hayabusa probe, we plan to visit the C-type asteroid 162137 Ryugu (1999 JU3), and to sample surface materials of the C-type asteroid that is likely to be different from the S-type asteroid Itokawa and contain more pristine materials, including organic matter and/or hydrated minerals, than S-type asteroids. We developed the Hayabusa2 sampler to collect a minimum of 100 mg of surface samples including several mm-sized particles at three surface locations without any severe terrestrial contamination. The basic configuration of the sampler design is mainly as same as the 1st Hayabusa (Yano et al. in Science, 312(5778):1350-1353, 2006), with several minor but important modifications based on lessons learned from the Hayabusa to fulfill the scientific requirements and to raise the scientific value of the returned samples.

Logistics system design for biomass-to-bioenergy industry with multiple types of feedstocks.

PubMed

Zhu, Xiaoyan; Yao, Qingzhu

2011-12-01

It is technologically possible for a biorefinery to use a variety of biomass as feedstock including native perennial grasses (e.g., switchgrass) and agricultural residues (e.g., corn stalk and wheat straw). Incorporating the distinct characteristics of various types of biomass feedstocks and taking into account their interaction in supplying the bioenergy production, this paper proposed a multi-commodity network flow model to design the logistics system for a multiple-feedstock biomass-to-bioenergy industry. The model was formulated as a mixed integer linear programming, determining the locations of warehouses, the size of harvesting team, the types and amounts of biomass harvested/purchased, stored, and processed in each month, the transportation of biomass in the system, and so on. This paper demonstrated the advantages of using multiple types of biomass feedstocks by comparing with the case of using a single feedstock (switchgrass) and analyzed the relationship of the supply capacity of biomass feedstocks to the output and cost of biofuel. Copyright © 2011 Elsevier Ltd. All rights reserved.

Design of air-gapped magnetic-core inductors for superimposed direct and alternating currents

NASA Technical Reports Server (NTRS)

Ohri, A. K.; Wilson, T. G.; Owen, H. A., Jr.

1976-01-01

Using data on standard magnetic-material properties and standard core sizes for air-gap-type cores, an algorithm designed for a computer solution is developed which optimally determines the air-gap length and locates the quiescent point on the normal magnetization curve so as to yield an inductor design with the minimum number of turns for a given ac voltage and frequency and with a given dc bias current superimposed in the same winding. Magnetic-material data used in the design are the normal magnetization curve and a family of incremental permeability curves. A second procedure, which requires a simpler set of calculations, starts from an assigned quiescent point on the normal magnetization curve and first screens candidate core sizes for suitability, then determines the required turns and air-gap length.

Joint Optimization of Distribution Network Design and Two-Echelon Inventory Control with Stochastic Demand and CO2 Emission Tax Charges

PubMed Central

Li, Shuangyan; Li, Xialian; Zhang, Dezhi; Zhou, Lingyun

2017-01-01

This study develops an optimization model to integrate facility location and inventory control for a three-level distribution network consisting of a supplier, multiple distribution centers (DCs), and multiple retailers. The integrated model addressed in this study simultaneously determines three types of decisions: (1) facility location (optimal number, location, and size of DCs); (2) allocation (assignment of suppliers to located DCs and retailers to located DCs, and corresponding optimal transport mode choices); and (3) inventory control decisions on order quantities, reorder points, and amount of safety stock at each retailer and opened DC. A mixed-integer programming model is presented, which considers the carbon emission taxes, multiple transport modes, stochastic demand, and replenishment lead time. The goal is to minimize the total cost, which covers the fixed costs of logistics facilities, inventory, transportation, and CO2 emission tax charges. The aforementioned optimal model was solved using commercial software LINGO 11. A numerical example is provided to illustrate the applications of the proposed model. The findings show that carbon emission taxes can significantly affect the supply chain structure, inventory level, and carbon emission reduction levels. The delay rate directly affects the replenishment decision of a retailer. PMID:28103246

Implications of the growth of dental education in India.

PubMed

Mahal, Ajay S; Shah, Naseem

2006-08-01

By influencing the supply of trained human resources, the dental education sector can play a significant role in influencing policy goals of ensuring good quality and equitable access to oral health services in developing countries. Our research goal was to assess quantitatively the size of the Indian dental education sector, its growth over time, and the implications of this growth for equity and quality in oral health care. Information on the location of teaching institutions, the year of establishment, type of ownership, and seat capacity was obtained from government sources, the Dental Council of India, and websites of individual institutions to estimate the growth in the undergraduate dental education sector, including the role of the private sector from 1950 to 2005. Data on location of training capacity and institutions were used to assess the geographical distribution of undergraduate dental education capacity in India. Registration data on dentists, the size of available faculty relative to regulatory requirements, and penalties imposed on offending faculty and education institutions were used to assess the impact of the growing Indian dental education sector on graduate quality and equitable access. Dental colleges and enrollment capacity have grown rapidly over the five decades since 1950, mainly due to a growing private sector. There is regional inequality in the location of dental education schools in India with a bias toward economically better-off regions. The growth in the dental education sector has translated into increased overall access, although accompanied by rising inequality in access and possibly lower quality of dental education.

Factors affecting ground-water exchange and catchment size for Florida lakes in mantled karst terrain

USGS Publications Warehouse

Lee, Terrie Mackin

2002-01-01

In the mantled karst terrain of Florida, the size of the catchment delivering ground-water inflow to lakes is often considerably smaller than the topographically defined drainage basin. The size is determined by a balance of factors that act individually to enhance or diminish the hydraulic connection between the lake and the adjacent surficial aquifer, as well as the hydraulic connection between the surficial aquifer and the deeper limestone aquifer. Factors affecting ground-water exchange and the size of the ground-water catchment for lakes in mantled karst terrain were examined by: (1) reviewing the physical and hydrogeological characteristics of 14 Florida lake basins with available ground-water inflow estimates, and (2) simulating ground-water flow in hypothetical lake basins. Variably-saturated flow modeling was used to simulate a range of physical and hydrogeologic factors observed at the 14 lake basins. These factors included: recharge rate to the surficial aquifer, thickness of the unsaturated zone, size of the topographically defined basin, depth of the lake, thickness of the surficial aquifer, hydraulic conductivity of the geologic units, the location and size of karst subsidence features beneath and onshore of the lake, and the head in the Upper Floridan aquifer. Catchment size and the magnitude of ground-water inflow increased with increases in recharge rate to the surficial aquifer, the size of the topographically defined basin, hydraulic conductivity in the surficial aquifer, the degree of confinement of the deeper Upper Floridan aquifer, and the head in the Upper Floridan aquifer. The catchment size and magnitude of ground-water inflow increased with decreases in the number and size of karst subsidence features in the basin, and the thickness of the unsaturated zone near the lake. Model results, although qualitative, provided insights into: (1) the types of lake basins in mantled karst terrain that have the potential to generate small and large amounts of ground-water inflow, and (2) the location of ground-water catchments that could be managed to safeguard lake water quality. Knowledge of how ground-water catchments are related to lakes could be used by water-resource managers to recommend setback distances for septic tank drain fields, agricultural land uses, and other land-use practices that contribute nutrients and major ions to lakes.

Association of Urinary Activity of MMP-2 with Microalbuminuria in an Isolated Sample of Subjects Living in High Altitude Rural Locations in México.

PubMed

Hernández-Hernández, Magda Elena; Morales-Romero, Jaime; Sampieri, Clara Luz; Luna Lozano, Diego Jesús; Valencia Lezama, Isidra Del Carmen; Muñoz Contreras, Mónica Janett; Rodríguez Hernández, Arturo

2017-09-01

Hernández-Hernández, Magda Elena, Jaime Morales-Romero, Clara Luz Sampieri, Diego Jesús Luna Lozano, Isidra del Carmen Valencia Lezama, Mónica Janett Muñoz Contreras, and Arturo Rodríguez Hernández. Association of urinary activity of MMP-2 with microalbuminuria in an isolated sample of subjects living in high altitude rural locations in México. High Alt Med Biol. 18:209-218, 2017.-Matrix metalloproteinases (MMP) are implicated in remodeling of the renal extracellular matrix. In a cross-sectional study we evaluated renal impairment in general population of high-altitude rural locations in México. Multivariable analysis was performed to identify the association between MMP-2 and MMP-9 and microalbuminuria. Twenty-eight (20.9%) subjects with renal impairment (WRI) and 106 (79.1%) without renal impairment were included. No differences were found relating to sex, location, marital status, current habits, weight, height, body mass index, waist size in males, creatinine in males, and uric acid. In contrast, differences were found among age, level of education, waist size in general and in females, creatinine in general and in females, urinary albumin, urea, glucose, total cholesterol, and triglycerides. Proportions of hypertension, type 2 diabetes mellitus, central abdominal obesity, hypertriglyceridemia, and hypercholesterolemia were greater in the group WRI. Presence of urinary MMP-2 or of both urinary gelatinases and arbitrary unit (AU) values ≥P 90 were associated with microalbuminuria. We conclude that AU values ≥P 90 of urinary MMP-2 (OR = 20.1, p = 0.002) is associated with microalbuminuria.

CoLIde

PubMed Central

Mohorianu, Irina; Stocks, Matthew Benedict; Wood, John; Dalmay, Tamas; Moulton, Vincent

2013-01-01

Small RNAs (sRNAs) are 20–25 nt non-coding RNAs that act as guides for the highly sequence-specific regulatory mechanism known as RNA silencing. Due to the recent increase in sequencing depth, a highly complex and diverse population of sRNAs in both plants and animals has been revealed. However, the exponential increase in sequencing data has also made the identification of individual sRNA transcripts corresponding to biological units (sRNA loci) more challenging when based exclusively on the genomic location of the constituent sRNAs, hindering existing approaches to identify sRNA loci.   To infer the location of significant biological units, we propose an approach for sRNA loci detection called CoLIde (Co-expression based sRNA Loci Identification) that combines genomic location with the analysis of other information such as variation in expression levels (expression pattern) and size class distribution. For CoLIde, we define a locus as a union of regions sharing the same pattern and located in close proximity on the genome. Biological relevance, detected through the analysis of size class distribution, is also calculated for each locus. CoLIde can be applied on ordered (e.g., time-dependent) or un-ordered (e.g., organ, mutant) series of samples both with or without biological/technical replicates. The method reliably identifies known types of loci and shows improved performance on sequencing data from both plants (e.g., A. thaliana, S. lycopersicum) and animals (e.g., D. melanogaster) when compared with existing locus detection techniques. CoLIde is available for use within the UEA Small RNA Workbench which can be downloaded from: http://srna-workbench.cmp.uea.ac.uk. PMID:23851377

CoLIde: a bioinformatics tool for CO-expression-based small RNA Loci Identification using high-throughput sequencing data.

PubMed

Mohorianu, Irina; Stocks, Matthew Benedict; Wood, John; Dalmay, Tamas; Moulton, Vincent

2013-07-01

Small RNAs (sRNAs) are 20-25 nt non-coding RNAs that act as guides for the highly sequence-specific regulatory mechanism known as RNA silencing. Due to the recent increase in sequencing depth, a highly complex and diverse population of sRNAs in both plants and animals has been revealed. However, the exponential increase in sequencing data has also made the identification of individual sRNA transcripts corresponding to biological units (sRNA loci) more challenging when based exclusively on the genomic location of the constituent sRNAs, hindering existing approaches to identify sRNA loci. To infer the location of significant biological units, we propose an approach for sRNA loci detection called CoLIde (Co-expression based sRNA Loci Identification) that combines genomic location with the analysis of other information such as variation in expression levels (expression pattern) and size class distribution. For CoLIde, we define a locus as a union of regions sharing the same pattern and located in close proximity on the genome. Biological relevance, detected through the analysis of size class distribution, is also calculated for each locus. CoLIde can be applied on ordered (e.g., time-dependent) or un-ordered (e.g., organ, mutant) series of samples both with or without biological/technical replicates. The method reliably identifies known types of loci and shows improved performance on sequencing data from both plants (e.g., A. thaliana, S. lycopersicum) and animals (e.g., D. melanogaster) when compared with existing locus detection techniques. CoLIde is available for use within the UEA Small RNA Workbench which can be downloaded from: http://srna-workbench.cmp.uea.ac.uk.

A mobile asset sharing policy for hospitals with real time locating systems.

PubMed

Demircan-Yıldız, Ece Arzu; Fescioglu-Unver, Nilgun

2016-01-01

Each year, hospitals lose a considerable amount of time and money due to misplaced mobile assets. In addition the assets which remain in departments that frequently use them depreciate early, while other assets of the same type in different departments are rarely used. A real time locating system can prevent these losses when used with appropriate asset sharing policies. This research quantifies the amount of time a medium size hospital saves by using real time locating system and proposes an asset selection rule to eliminate the asset usage imbalance problem. The asset selection rule proposed is based on multi objective optimization techniques. The effectiveness of this rule on asset to patient time and asset utilization rate variance performance measures were tested using discrete event simulation method. Results show that the proposed asset selection rule improved the usage balance significantly. Sensitivity analysis showed that the proposed rule is robust to changes in demand rates and user preferences. Real time locating systems enable saving considerable amount of time in hospitals, and they can still be improved by integrating decision support mechanisms. Combining tracking technology and asset selection rules helps improve healthcare services.

Siting and sizing of distributed generators based on improved simulated annealing particle swarm optimization.

PubMed

Su, Hongsheng

2017-12-18

Distributed power grids generally contain multiple diverse types of distributed generators (DGs). Traditional particle swarm optimization (PSO) and simulated annealing PSO (SA-PSO) algorithms have some deficiencies in site selection and capacity determination of DGs, such as slow convergence speed and easily falling into local trap. In this paper, an improved SA-PSO (ISA-PSO) algorithm is proposed by introducing crossover and mutation operators of genetic algorithm (GA) into SA-PSO, so that the capabilities of the algorithm are well embodied in global searching and local exploration. In addition, diverse types of DGs are made equivalent to four types of nodes in flow calculation by the backward or forward sweep method, and reactive power sharing principles and allocation theory are applied to determine initial reactive power value and execute subsequent correction, thus providing the algorithm a better start to speed up the convergence. Finally, a mathematical model of the minimum economic cost is established for the siting and sizing of DGs under the location and capacity uncertainties of each single DG. Its objective function considers investment and operation cost of DGs, grid loss cost, annual purchase electricity cost, and environmental pollution cost, and the constraints include power flow, bus voltage, conductor current, and DG capacity. Through applications in an IEEE33-node distributed system, it is found that the proposed method can achieve desirable economic efficiency and safer voltage level relative to traditional PSO and SA-PSO algorithms, and is a more effective planning method for the siting and sizing of DGs in distributed power grids.

Characteristics of the patients undergoing surgical treatment for pneumothorax: A descriptive study.

PubMed

Cakmak, Muharrem; Yuksel, Melih; Kandemir, Mehmet Nail

2016-05-01

To identify the characteristic features of pneumothorax patients treated surgically. The retrospective study was conducted at Gazi Yasargil Education and Research Hospital Thoracic Surgery Clinic, Diyarbakir, Turkey and comprised records of pneumothorax patients from January 2004 to December 2014. They were divided into two groups as spontaneous and traumatic. Patients who had not undergone any surgical intervention were excluded. Mean age, gender distribution, location of the disease, type of pneumothorax, and treatment method were noted. Among patients with spontaneous pneumothorax, age and months distribution, smoking habits, pneumothorax size, and treatment method were assessed. The effect of gender, location, comorbid disease, smoking, subgroup of disease, and pneumothorax size on surgical procedures were also investigated. The mean age of the 672 patients in the study was 34.5±6.17 years. There were 611(91%) men and 61(9%) women. Disease was on the right side in 360(53.6%) patients, on the left side in 308(45.8%), and bilateral in 4(0.59%). Besides, 523(77.8%) patients had spontaneous, and 149(22.7%) had traumatic pneumothorax. Overall, 561(83.5%) patients had been treated with tube thoracostomy, whereas 111(16.5%) were treated with thoracotomy/thoracoscopic surgery. The presence of comorbid diseases, being primary, and being total or subtotal according to partial were found to create predisposition to thoracotomy/ thoracoscopic surgery (p<0.05 each). In the case of pneumothorax being total, the presence of comorbid diseases, and the increase in pneumothorax size, thoracotomy or thoracoscopic surgery is preferred.

Tumour location within the breast: Does tumour site have prognostic ability?

PubMed

Rummel, Seth; Hueman, Matthew T; Costantino, Nick; Shriver, Craig D; Ellsworth, Rachel E

2015-01-01

Tumour location within the breast varies with the highest frequency in the upper outer quadrant (UOQ) and lowest frequency in the lower inner quadrant (LIQ). Whether tumour location is prognostic is unclear. To determine whether tumour location is prognostic, associations between tumour site and clinicopathological characteristics were evaluated. All patients enrolled in the Clinical Breast Care Project whose tumour site-UOQ, upper inner quadrant (UIQ), central, LIQ, lower outer quadrant (LOQ)-was determined by a single, dedicated breast pathologist were included in this study. Patients with multicentric disease (n = 122) or tumours spanning multiple quadrants (n = 381) were excluded from further analysis. Clinicopathological characteristics were analysed using chi-square tests for univariate analysis with multivariate analysis performed using principal components analysis (PCA) and multiple logistic regression. Significance was defined as P < 0.05. Of the 980 patients with defined tumour location, 30 had bilateral disease. Tumour location in the UOQ (51.5%) was significantly higher than in the UIQ (15.6%), LOQ (14.2%), central (10.6%), or LIQ (8.1%). Tumours in the central quadrant were significantly more likely to have higher tumour stage (P = 0.003) and size (P < 0.001), metastatic lymph nodes (P < 0.001), and mortality (P = 0.011). After multivariate analysis, only tumour size and lymph node status remained significantly associated with survival. Evaluation of tumour location as a prognostic factor revealed that although tumours in the central region are associated with less favourable outcome, these associations are not independent of location but rather driven by larger tumour size. Tumours in the central region are more difficult to detect mammographically, resulting in larger tumour size at diagnosis and thus less favourable prognosis. Together, these data demonstrate that tumour location is not an independent prognostic factor.

Identification of Novel Linear Megaplasmids Carrying a ß-Lactamase Gene in Neurotoxigenic Clostridium butyricum Type E Strains

PubMed Central

Franciosa, Giovanna; Scalfaro, Concetta; Di Bonito, Paola; Vitale, Marco; Aureli, Paolo

2011-01-01

Since the first isolation of type E botulinum toxin-producing Clostridium butyricum from two infant botulism cases in Italy in 1984, this peculiar microorganism has been implicated in different forms of botulism worldwide. By applying particular pulsed-field gel electrophoresis run conditions, we were able to show for the first time that ten neurotoxigenic C. butyricum type E strains originated from Italy and China have linear megaplasmids in their genomes. At least four different megaplasmid sizes were identified among the ten neurotoxigenic C. butyricum type E strains. Each isolate displayed a single sized megaplasmid that was shown to possess a linear structure by ATP-dependent exonuclease digestion. Some of the neurotoxigenic C. butyricum type E strains possessed additional smaller circular plasmids. In order to investigate the genetic content of the newly identified megaplasmids, selected gene probes were designed and used in Southern hybridization experiments. Our results revealed that the type E botulinum neurotoxin gene was chromosome-located in all neurotoxigenic C. butyricum type E strains. Similar results were obtained with the 16S rRNA, the tetracycline tet(P) and the lincomycin resistance protein lmrB gene probes. A specific mobA gene probe only hybridized to the smaller plasmids of the Italian C. butyricum type E strains. Of note, a ß-lactamase gene probe hybridized to the megaplasmids of eight neurotoxigenic C. butyricum type E strains, of which seven from clinical sources and the remaining one from a food implicated in foodborne botulism, whereas this ß-lactam antibiotic resistance gene was absent form the megaplasmids of the two soil strains examined. The widespread occurrence among C. butyricum type E strains associated to human disease of linear megaplasmids harboring an antibiotic resistance gene strongly suggests that the megaplasmids could have played an important role in the emergence of C. butyricum type E as a human pathogen. PMID:21738770

Variation in the isotopic composition of striped weakfish Cynoscion guatucupa of the Southwest Atlantic Ocean in response to dietary shifts.

PubMed

Viola, M N Paso; Riccialdelli, L; Jaureguizar, A; Panarello, H O; Cappozzo, H L

2018-05-01

The aim of this study was to analyze the isotopic composition in muscle of striped weakfish Cynoscion guatucupa from Southwest Atlantic Ocean in order to evaluate a possible variation in δ13C and δ15N in response to dietary shifts that occur as animals grow. We also explored for isotopic evidence of differences between sample locations. The results showed an agreement between isotope analysis and previous conventional studies. Differences in the isotope composition between sampling location were not observed. A positive relation exists between isotope values and total body length of the animals. The Cluster analysis defined three groups of size classes, validated by the MDS. Differences in the relative consumption of prey species in each size class were also observed performing isotope mixing models (SIAR). Variation in δ15N among size classes would be associated with the consumption of a different type of prey as animals grow. Small striped weakfish feed on small crustaceans and progressively increase their consumption of fish (anchovy, Engraulis anchoita), increasing by this way their isotope values. On the other hand, differences in δ13C values seemed to be related to age-class specific spatial distribution patterns. Therefore, large and small striped weakfish remain specialized but feeding on different prey at different trophic levels. These results contribute to the study of the diet of striped weakfish, improve the isotopic ecology models and highlight on the importance of accounting for variation in the isotopic composition in response to dietary shifts with the size of one of the most important fishery resources in the region.

GEONETCast Americas - Architecture

Science.gov Websites

FengYunCast covers Asia. See the following picture for a global view of the planned GEONETCast satellite participants. (Click drawing to enlarge) Map of world showing satellite size required to receive GEONETCast Americas according to location Satellite dish size required, according to location. (Click drawing to

Simulation of the Formation of DNA Double Strand Breaks and Chromosome Aberrations in Irradiated Cells

NASA Technical Reports Server (NTRS)

Plante, Ianik; Ponomarev, Artem L.; Wu, Honglu; Blattnig, Steve; George, Kerry

2014-01-01

The formation of DNA double-strand breaks (DSBs) and chromosome aberrations is an important consequence of ionizing radiation. To simulate DNA double-strand breaks and the formation of chromosome aberrations, we have recently merged the codes RITRACKS (Relativistic Ion Tracks) and NASARTI (NASA Radiation Track Image). The program RITRACKS is a stochastic code developed to simulate detailed event-by-event radiation track structure: [1] This code is used to calculate the dose in voxels of 20 nm, in a volume containing simulated chromosomes, [2] The number of tracks in the volume is calculated for each simulation by sampling a Poisson distribution, with the distribution parameter obtained from the irradiation dose, ion type and energy. The program NASARTI generates the chromosomes present in a cell nucleus by random walks of 20 nm, corresponding to the size of the dose voxels, [3] The generated chromosomes are located within domains which may intertwine, and [4] Each segment of the random walks corresponds to approx. 2,000 DNA base pairs. NASARTI uses pre-calculated dose at each voxel to calculate the probability of DNA damage at each random walk segment. Using the location of double-strand breaks, possible rejoining between damaged segments is evaluated. This yields various types of chromosomes aberrations, including deletions, inversions, exchanges, etc. By performing the calculations using various types of radiations, it will be possible to obtain relative biological effectiveness (RBE) values for several types of chromosome aberrations.

Northern bobwhite predator avoidance behavior in response to varying types of threat

USGS Publications Warehouse

Perkins, R.A.; Boal, Clint W.; Rollins, Dale; Perez, R.

2014-01-01

The flight behavior and cover use of northern bobwhite (Colinus virginianus) have been examined in several studies, but the current data lack quantitative measures of how bobwhites respond to natural threats. We examined aspects of bobwhite behavior in response to 4 threat categories: researcher, hunter, raptor, and mammal. We found that bobwhite flight distance is best predicted by threat type and covey size, and bobwhite flight speed is best predicted by threat type. Bobwhites flushed by the hunter threat and the raptor threat selected for significantly taller obstruction at landing sites than was randomly available, with average heights of 6.2cm taller (P=0.034), and 38.1cm taller (P<0.001), respectively. Raptor-flushed bobwhites also selected for significantly denser shrub cover (42.2%, P<0.001) and a lower angle of obstruction (70.4 degrees, P<0.001) at landing points than was randomly available. In the process of data collection, we also observed bobwhite roost locations have lower visual height obstruction (7.3cm, P=0.03), lower shrub intercept (10.1%, P=0.02), and greater angles of obstruction (18.5 degrees, P=0.005) than bobwhite diurnal locations; this may facilitate escape from nocturnal mammalian predators. Our results suggest that bobwhite escape strategies and cover use vary among threat types. These results support current management recommendations of creating a patchwork of vegetation covers for bobwhites but also suggest how a more complete understanding of bobwhite behavior would improve management and conservation efforts.

Generating size-controlled embryoid bodies using laser direct-write.

PubMed

Dias, A D; Unser, A M; Xie, Y; Chrisey, D B; Corr, D T

2014-06-01

Embryonic stem cells (ESCs) have the potential to self-renew and differentiate into any specialized cell type. One common method to differentiate ESCs in vitro is through embryoid bodies (EBs), three-dimensional cellular aggregates that spontaneously self-assemble and generally express markers for the three germ layers, endoderm, ectoderm, and mesoderm. It has been previously shown that both EB size and 2D colony size each influence differentiation. We hypothesized that we could control the size of the EB formed by mouse ESCs (mESCs) by using a cell printing method, laser direct-write (LDW), to control both the size of the initial printed colony and the local cell density in printed colonies. After printing mESCs at various printed colony sizes and printing densities, two-way ANOVAs indicated that the EB diameter was influenced by printing density after three days (p = 0.0002), while there was no effect of the printed colony diameter on the EB diameter at the same timepoint (p = 0.74). There was no significant interaction between these two factors. Tukey's honestly significant difference test showed that high-density colonies formed significantly larger EBs, suggesting that printed mESCs quickly aggregate with nearby cells. Thus, EBs can be engineered to a desired size by controlling printing density, which will influence the design of future differentiation studies. Herein, we highlight the capacity of LDW to control the local cell density and colony size independently, at prescribed spatial locations, potentially leading to better stem cell maintenance and directed differentiation.

A passive cold storage device economic model to evaluate selected immunization location scenarios.

PubMed

Norman, Bryan A; Nourollahi, Sevnaz; Chen, Sheng-I; Brown, Shawn T; Claypool, Erin G; Connor, Diana L; Schmitz, Michelle M; Rajgopal, Jayant; Wateska, Angela R; Lee, Bruce Y

2013-10-25

The challenge of keeping vaccines cold at health posts given the unreliability of power sources in many low- and middle-income countries and the expense and maintenance requirements of solar refrigerators has motivated the development of passive cold storage devices (PCDs), containers that keep vaccines cold without using an active energy source. With different PCDs under development, manufacturers, policymakers and funders need guidance on how varying different PCD characteristics may affect the devices' cost and utility. We developed an economic spreadsheet model representing the lowest two levels of a typical Expanded Program on Immunization (EPI) vaccine supply chain: a district store, the immunization locations that the district store serves, and the transport vehicles that operate between the district store and the immunization locations. The model compares the use of three vaccine storage device options [(1) portable PCDs, (2) stationary PCDs, or (3) solar refrigerators] and allows the user to vary different device (e.g., size and cost) and scenario characteristics (e.g., catchment area population size and vaccine schedule). For a sample set of select scenarios and equipment specification, we found the portable PCD to generally be better suited to populations of 5,000 or less. The stationary PCD replenished once per month can be a robust design especially with a 35L capacity and a cost of $2,500 or less. The solar device was generally a reasonable alternative for most of the scenarios explored if the cost was $2,100 or less (including installation). No one device type dominated over all explored circumstances. Therefore, the best device may vary from country-to-country and location-to-location within a country. This study introduces a quantitative model to help guide PCD development. Although our selected set of explored scenarios and device designs was not exhaustive, future explorations can further alter model input values to represent additional scenarios and device designs. Copyright © 2013 Elsevier Ltd. All rights reserved.

Arabic OCR: toward a complete system

NASA Astrophysics Data System (ADS)

El-Bialy, Ahmed M.; Kandil, Ahmed H.; Hashish, Mohamed; Yamany, Sameh M.

1999-12-01

Latin and Chinese OCR systems have been studied extensively in the literature. Yet little work was performed for Arabic character recognition. This is due to the technical challenges found in the Arabic text. Due to its cursive nature, a powerful and stable text segmentation is needed. Also; features capturing the characteristics of the rich Arabic character representation are needed to build the Arabic OCR. In this paper a novel segmentation technique which is font and size independent is introduced. This technique can segment the cursive written text line even if the line suffers from small skewness. The technique is not sensitive to the location of the centerline of the text line and can segment different font sizes and type (for different character sets) occurring on the same line. Features extraction is considered one of the most important phases of the text reading system. Ideally, the features extracted from a character image should capture the essential characteristics of this character that are independent of the font type and size. In such ideal case, the classifier stores a single prototype per character. However, it is practically challenging to find such ideal set of features. In this paper, a set of features that reflect the topological aspects of Arabia characters is proposed. These proposed features integrated with a topological matching technique introduce an Arabic text reading system that is semi Omni.

SEM/EDS Characterization of Ambient PM during Agricultural Burns

NASA Astrophysics Data System (ADS)

Wagner, J.; Wall, S.

2010-12-01

Ambient particulate matter (PM) samples were collected with UNC passive samplers during agricultural burns in Imperial Valley, California. Four Bermuda grass field burn events were sampled at 3-8 locations surrounding each burn. Sampling began at the start of each burn (30-60 min) and continued for 24-120 hours. During 3 of the 4 burn events, winds were calm and plumes were observed to travel straight up to the inversion layer. In one event, winds created a ground-level plume that enveloped two UNC samplers mounted on telephone poles very close to the field (0.2-0.3 miles away). Computer-controlled scanning electron microscopy / energy-dispersive x-ray spectroscopy (CCSEM/EDS) was used to measure particle sizes and elemental composition, from which mass concentrations and size distributions were calculated. The median PM2.5 and PM10 levels measured in this study were 3.4 and 20 ug/m3, respectively. To determine quantitative accuracy, UNC sampler PM2.5 results (PM< 2.5 um) were compared to PM2.5 results from four co-located, continuous-reading beta-attenuation monitors (EBAMs). The median agreement (EBAM - UNC) was 3.8 ug/m3. Manual SEM/EDS detected various distinctive species in these samples, including sea salt, spores, plant fragments, and large soot agglomerates. During the ‘plume event’, 24-hour PM2.5 exposures downwind were up to 17 times higher than that measured upwind. Numerous submicron combustion particles with carbon and oxygen only were directly observed by manual SEM/EDS in the two plume-impacted samples, along with larger ash particles enriched in potassium, sulfur, chlorine, calcium, sodium, and phosphorus. CCSEM/EDS data from this event was grouped into 5 particle classes to generate size-fraction-specific pie charts. Burn-related particle types contributed 95% of the PM2.5 in the location directly impacted by the ground-level plume, compared to only 12% in the upwind location. A sample of Imperial County Bermuda grass analyzed in bulk and partially-burned states was found to contain similar inorganic elements as the air samples impacted by the burn plume, as well as mold spores found at trace levels in various air samples.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pawellek, Nicole; Krivov, Alexander V.; Marshall, Jonathan P.

The radii of debris disks and the sizes of their dust grains are important tracers of the planetesimal formation mechanisms and physical processes operating in these systems. Here we use a representative sample of 34 debris disks resolved in various Herschel Space Observatory (Herschel is an ESA space observatory with science instruments provided by European-led Principal Investigator consortia and with important participation from NASA) programs to constrain the disk radii and the size distribution of their dust. While we modeled disks with both warm and cold components, and identified warm inner disks around about two-thirds of the stars, we focusmore » our analysis only on the cold outer disks, i.e., Kuiper-belt analogs. We derive the disk radii from the resolved images and find a large dispersion for host stars of any spectral class, but no significant trend with the stellar luminosity. This argues against ice lines as a dominant player in setting the debris disk sizes, since the ice line location varies with the luminosity of the central star. Fixing the disk radii to those inferred from the resolved images, we model the spectral energy distribution to determine the dust temperature and the grain size distribution for each target. While the dust temperature systematically increases toward earlier spectral types, the ratio of the dust temperature to the blackbody temperature at the disk radius decreases with the stellar luminosity. This is explained by a clear trend of typical sizes increasing toward more luminous stars. The typical grain sizes are compared to the radiation pressure blowout limit s {sub blow} that is proportional to the stellar luminosity-to-mass ratio and thus also increases toward earlier spectral classes. The grain sizes in the disks of G- to A-stars are inferred to be several times s {sub blow} at all stellar luminosities, in agreement with collisional models of debris disks. The sizes, measured in the units of s {sub blow}, appear to decrease with the luminosity, which may be suggestive of the disk's stirring level increasing toward earlier-type stars. The dust opacity index β ranges between zero and two, and the size distribution index q varies between three and five for all the disks in the sample.« less

Aerial ULV control of Aedes aegypti with naled (Dibrom) inside simulated rural village and urban cryptic habitats

PubMed Central

Linthicum, Kenneth J.; Aldridge, Robert L.; Breidenbaugh, Mark S.; Latham, Mark D.; Connelly, Peter H.; Rush, Mattie J. E.; Remmers, Jennifer L.; Kerce, Jerry D.; Silcox, Charles A.

2018-01-01

We conducted aerial fixed wing ultra low volume (ULV) spray trials with naled to investigate penetration of exposed and simulated cryptic habitat within opened buildings, partially sealed buildings, and outdoor locations targeting sentinel adult Aedes aegypti mosquitoes in north central Florida. Mortality was observed in open and closed buildings and outdoors, even in mosquitoes placed in cryptic habitats. Observations on the impact of building type, mosquito exposure method such as placement in cryptic habitat, and spray nozzle size on mosquito mortality are described and analyzed. PMID:29352307

Karst in Wadi Bani Khalid, Oman

NASA Astrophysics Data System (ADS)

Abdelaziz, Ramadan

2017-04-01

There are several important in Oman. The main aquifer is surficial aquifer and fractured rocks. In fact, the geology of Oman is complex whichmake the hydraulic continuity of bedrock is limited and formaing localized aquifers. caves in Oman are varying types and length, size and geographic formations. Many caves and valleys founded in Oman. Wadi Bani Khalid hosts complex network of fractured rock. Karst in Wadi Bani Kalid made upof Limestone(Calcium, which is dissolve in water.A rain water pass through the rock it is erode the rock and form caves. The cave located in Miqil. The karst was formed in Calcium Carbonate rocks.

Treatment modalities and outcomes of pleomorphic hyalinizing angiectatic tumor: a systematic review of the literature.

PubMed

Rush, A J; Patel, P D; Shemesh, S; Subhawong, T K; Pretell-Mazzini, J

2018-02-01

A systematic review of the cases documented in the literature regarding Pleomorphic hyalinizing angiectatic tumor of soft parts (PHAT) was performed in order to identify (1) location on presentation (2) surgical treatment modality (3) recurrence rate (4) any associations between location, age, histology, surgery type on recurrence. A systematic review of medical literature listed on PubMed was conducted identifying any prior case report and/or case series of diagnosed PHAT, with no exclusion based on language or time. Twenty-nine articles were identified removing any articles with duplicated cases yielding a total of 93 cases. Cases were broken down by gender, presenting location (UE/LE/axial), surgery type [wide local resection, non-wide local, wide local with radiation therapy (RT), non-wide local with RT], recurrence, and time to recurrence. The mean age at presentation was 54.5 ± 17.1 (range 10-89) with the 76% of cases appearing in the lower extremity (15% UE, 9% Axial). Of the 93 patients, 74 had a known surgical procedure, 31% WL, 40% NWL, 8% WL + RT, 1% NWL + RT. Of those treated surgically, 63 pts had documented follow-up and 18 (29%) had recurrence. A strong association was observed between surgery type and recurrence. Local recurrence was more common within the group undergoing NWLE in 52% (16/41) of cases (p = 0.002). Kaplan-Meier analysis showed an estimate mean time for recurrence of 43.87 months [95% confidence interval (CI) 24.52-63.22; and standard error (SE) 7.59] for the entire population. A trend was also seen toward males having a shorter disease-free survival than females (29.4 mos. vs. 69.5 mos.). No significant association seen between size, location, histology type and recurrence. PHAT has a characteristic presentation in the LE with a relatively high rate of local recurrence and slow-growing potential. Wide local excision appears to be superior in decreasing recurrence rates and a long-term follow-up period is needed.

Investigating the Geomorphic and Ecologic Functions of Wood in Relationship to Habitat Type and Salmonid Redds on a Regulated California River

NASA Astrophysics Data System (ADS)

Senter, A. E.; Pasternack, G. B.

2006-12-01

Most river rehabilitation projects incorporate little to no wood in current designs, and those that do have little science to guide them. The overall goal of this research is to investigate the role of wood in a regulated, mid- sized (where river width is greater than most tree heights), Mediterranean-climate (where smaller, softer-wood trees dominate the landscape) river in order to provide a scientific foundation for the potential use of wood in rehabilitation projects within such systems. Wood structures in the active salmonid spawning reach of the Lower Mokelumne River in Central California were measured, mapped, and described during summer and fall 2006. Digital photos and GPS coordinates were used to establish wood location within the stream channel. Structural morphology was determined by measuring physical properties such as individual diameter and length, orientation to stream flow, and jam dimensions. In addition, qualitative attributes were recorded such as decay class and leaf, limb, bark, and root characteristics. A GIS wood layer will be created and added to a database of existing Mokelumne River GIS layers containing salmonid redd (salmon egg nests) densities, hydraulic conditions associated with individual redds, and sub-reach habitat types. An analysis of wood properties, redd locations and conditions, and habitat types will be used to develop a conceptual model of wood dynamics in relation to salmonid habitat on the Lower Mokelumne River. The primary products of this study will be (1) a scientific conceptual model of the role of wood in regulated gravel reaches of mid-size rivers in Mediterranean California and (2) a decision-making framework that will enable river managers to include scientifically based wood structures into rehabilitation designs, thereby enhancing spawning habitat, stream complexity, and biological diversity. These tools will be developed in collaboration with East Bay Municipal Utilities District to aid in the continuing rehabilitation of the Lower Mokelumne River.

Drop size distributions and related properties of fog for five locations measured from aircraft

NASA Technical Reports Server (NTRS)

Zak, J. Allen

1994-01-01

Fog drop size distributions were collected from aircraft as part of the Synthetic Vision Technology Demonstration Program. Three west coast marine advection fogs, one frontal fog, and a radiation fog were sampled from the top of the cloud to the bottom as the aircraft descended on a 3-degree glideslope. Drop size versus altitude versus concentration are shown in three dimensional plots for each 10-meter altitude interval from 1-minute samples. Also shown are median volume radius and liquid water content. Advection fogs contained the largest drops with median volume radius of 5-8 micrometers, although the drop sizes in the radiation fog were also large just above the runway surface. Liquid water content increased with height, and the total number of drops generally increased with time. Multimodal variations in number density and particle size were noted in most samples where there was a peak concentration of small drops (2-5 micrometers) at low altitudes, midaltitude peak of drops 5-11 micrometers, and high-altitude peak of the larger drops (11-15 micrometers and above). These observations are compared with others and corroborate previous results in fog gross properties, although there is considerable variation with time and altitude even in the same type of fog.

Measurement of J-integral in CAD/CAM dental ceramics and composite resin by digital image correlation.

PubMed

Jiang, Yanxia; Akkus, Anna; Roperto, Renato; Akkus, Ozan; Li, Bo; Lang, Lisa; Teich, Sorin

2016-09-01

Ceramic and composite resin blocks for CAD/CAM machining of dental restorations are becoming more common. The sample sizes affordable by these blocks are smaller than ideal for stress intensity factor (SIF) based tests. The J-integral measurement calls for full field strain measurement, making it challenging to conduct. Accordingly, the J-integral values of dental restoration materials used in CAD/CAM restorations have not been reported to date. Digital image correlation (DIC) provides full field strain maps, making it possible to calculate the J-integral value. The aim of this study was to measure the J-integral value for CAD/CAM restorative materials. Four types of materials (sintered IPS E-MAX CAD, non-sintered IPS E-MAX CAD, Vita Mark II and Paradigm MZ100) were used to prepare beam samples for three-point bending tests. J-integrals were calculated for different integral path size and locations with respect to the crack tip. J-integral at path 1 for each material was 1.26±0.31×10(-4)MPam for MZ 100, 0.59±0.28×10(-4)MPam for sintered E-MAX, 0.19±0.07×10(-4)MPam for VM II, and 0.21±0.05×10(-4)MPam for non-sintered E-MAX. There were no significant differences between different integral path size, except for the non-sintered E-MAX group. J-integral paths of non-sintered E-MAX located within 42% of the height of the sample provided consistent values whereas outside this range resulted in lower J-integral values. Moreover, no significant difference was found among different integral path locations. The critical SIF was calculated from J-integral (KJ) along with geometry derived SIF values (KI). KI values were comparable with KJ and geometry based SIF values obtained from literature. Therefore, DIC derived J-integral is a reliable way to assess the fracture toughness of small sized specimens for dental CAD/CAM restorative materials; however, with caution applied to the selection of J-integral path. Copyright © 2016 Elsevier Ltd. All rights reserved.

49 CFR 178.255-15 - Report.

Code of Federal Regulations, 2010 CFR

2010-10-01

... _______ Company Location Manufactured by _______ Company Location Consigned to _________ Company Location Size ___ feet outside diameter by ___ long. Marks on tank as prescribed by § 178.255-14 of this specification...

The effects of transient attention on spatial resolution and the size of the attentional cue.

PubMed

Yeshurun, Yaffa; Carrasco, Marisa

2008-01-01

It has been shown that transient attention enhances spatial resolution, but is the effect of transient attention on spatial resolution modulated by the size of the attentional cue? Would a gradual increase in the size of the cue lead to a gradual decrement in spatial resolution? To test these hypotheses, we used a texture segmentation task in which performance depends on spatial resolution, and systematically manipulated the size of the attentional cue: A bar of different lengths (Experiment 1) or a frame of different sizes (Experiments 2-3) indicated the target region in a texture segmentation display. Observers indicated whether a target patch region (oriented line elements in a background of an orthogonal orientation), appearing at a range of eccentricities, was present in the first or the second interval. We replicated the attentional enhancement of spatial resolution found with small cues; attention improved performance at peripheral locations but impaired performance at central locations. However, there was no evidence of gradual resolution decrement with large cues. Transient attention enhanced spatial resolution at the attended location when it was attracted to that location by a small cue but did not affect resolution when it was attracted by a large cue. These results indicate that transient attention cannot adapt its operation on spatial resolution on the basis of the size of the attentional cue.

The Identity-Location Binding Problem.

PubMed

Howe, Piers D L; Ferguson, Adam

2015-09-01

The binding problem is fundamental to visual perception. It is the problem of associating an object's visual properties with itself and not with some other object. The problem is made particular difficult because different properties of an object, such as its color, shape, size, and motion, are often processed independently, sometimes in different cortical areas. The results of these separate analyses have to be combined before the object can be seen as a single coherent entity as opposed to a collection of unconnected features. Visual bindings are typically initiated and updated in a serial fashion, one object at a time. Here, we show that one type of binding, location-identity bindings, can be updated in parallel. We do this by using two complementary techniques, the simultaneous-sequential paradigm and systems factorial technology. These techniques make different assumptions and rely on different behavioral measures, yet both came to the same conclusion. Copyright © 2014 Cognitive Science Society, Inc.

Causes and Solutions for High Energy Consumption in Traditional Buildings Located in Hot Climate Regions

NASA Astrophysics Data System (ADS)

Barayan, Olfat Mohammad

A considerable amount of money for high-energy consumption is spent in traditional buildings located in hot climate regions. High-energy consumption is significantly influenced by several causes, including building materials, orientation, mass, and openings' sizes. This paper aims to identify these causes and find practical solutions to reduce the annual cost of bills. For the purpose of this study, simulation research method has been followed. A comparison between two Revit models has also been created to point out the major cause of high-energy consumption. By analysing different orientations, wall insulation, and window glazing and applying some other high performance building techniques, a conclusion was found to confirm that appropriate building materials play a vital role in affecting energy cost. Therefore, the ability to reduce the energy cost by more than 50% in traditional buildings depends on a careful balance of building materials, mass, orientation, and type of window glazing.

Stonehenge's Greater Cursus

NASA Astrophysics Data System (ADS)

Burley, Paul; Mooers, Howard D.

2016-01-01

Archaeological investigations have emphasized relationships between solar and lunar phenomena and architectural features of prehistoric sites located on the Stonehenge ritual landscape. However, no over-riding landscape design has been identified to explain the purpose of placing hundreds of Neolithic through Iron Age burial sites upon the landscape. Our research and analysis shows the mid-4th millennium BC (mid-Neolithic) landscape represents an 'above, so below' cosmo-geographical relationship. Type, shape, size and orientation of specific elements (such as long barrows, henges, cursus and topography) created a hierotopy representing the Winter Hexagon asterism, Milky Way, ecliptic and other stellar features. The resulting pattern of ritual sites represents translocation of the astronomical Otherworld - the Spirit World - onto the plain. Results of the analysis create a new paradigm of purpose for the built landscape circa 3500 BC, and identifies the reason why Stonehenge is located where it is with respect to other contemorary monuments.

Bodensee-Oberschwaben. Eine erfolgreiche Region fernab der Großstädte

NASA Astrophysics Data System (ADS)

Danielzyk, Rainer; Köhler, Stefan; Friedsmann, Philipp

2017-09-01

Bodensee-Oberschwaben is representative of a type of region that does not receive much attention in regional research. The region is located peripherally, away from the metropolises and urban agglomeration areas. Despite seemingly poor initial conditions, the region is economically very successful. A polycentric structure of many small and medium-sized towns characterize Bodensee-Oberschwaben as well as other attributes, which do not allow for classification into traditional categories such as rural or urban. Friedrichshafen, the largest city and the industrial core of the region, contributes significantly to its prosperity. The international high technology companies, which are located here, have their origins in the activities of Graf Zeppelin in the early 20th century. Regional universities and the strong network between actors both within the region as well as between Bodensee-Oberschwaben and the neighboring regions have also had a positive impact on region's development.

The linear sizes tolerances and fits system modernization

NASA Astrophysics Data System (ADS)

Glukhov, V. I.; Grinevich, V. A.; Shalay, V. V.

2018-04-01

The study is carried out on the urgent topic for technical products quality providing in the tolerancing process of the component parts. The aim of the paper is to develop alternatives for improving the system linear sizes tolerances and dimensional fits in the international standard ISO 286-1. The tasks of the work are, firstly, to classify as linear sizes the elements additionally linear coordinating sizes that determine the detail elements location and, secondly, to justify the basic deviation of the tolerance interval for the element's linear size. The geometrical modeling method of real details elements, the analytical and experimental methods are used in the research. It is shown that the linear coordinates are the dimensional basis of the elements linear sizes. To standardize the accuracy of linear coordinating sizes in all accuracy classes, it is sufficient to select in the standardized tolerance system only one tolerance interval with symmetrical deviations: Js for internal dimensional elements (holes) and js for external elements (shafts). The main deviation of this coordinating tolerance is the average zero deviation, which coincides with the nominal value of the coordinating size. Other intervals of the tolerance system are remained for normalizing the accuracy of the elements linear sizes with a fundamental change in the basic deviation of all tolerance intervals is the maximum deviation corresponding to the limit of the element material: EI is the lower tolerance for the of the internal elements (holes) sizes and es is the upper tolerance deviation for the outer elements (shafts) sizes. It is the sizes of the material maximum that are involved in the of the dimensional elements mating of the shafts and holes and determine the fits type.

Classification of immature mosquito species according to characteristics of the larval habitat in the subtropical province of Chaco, Argentina.

PubMed

Stein, Marina; Ludueña-Almeida, Francisco; Willener, Juana Alicia; Almirón, Walter Ricardo

2011-06-01

To classify mosquito species based on common features of their habitats, samples were obtained fortnightly between June 2001-October 2003 in the subtropical province of Chaco, Argentina. Data on the type of larval habitat, nature of the habitat (artificial or natural), size, depth, location related to sunlight, distance to the neighbouring houses, type of substrate, organic material, vegetation and algae type and their presence were collected. Data on the permanence, temperature, pH, turbidity, colour, odour and movement of the larval habitat's water were also collected. From the cluster analysis, three groups of species associated by their degree of habitat similarity were obtained and are listed below. Group 1 consisted of Aedes aegypti. Group 2 consisted of Culex imitator, Culex davisi, Wyeomyia muehlensi and Toxorhynchites haemorrhoidalis separatus. Within group 3, two subgroups are distinguished: A (Psorophora ferox, Psorophora cyanescens, Psorophora varinervis, Psorophora confinnis, Psorophora cingulata, Ochlerotatus hastatus-oligopistus, Ochlerotatus serratus, Ochlerotatus scapularis, Culex intrincatus, Culex quinquefasciatus, Culex pilosus, Ochlerotatus albifasciatus, Culex bidens) and B (Culex maxi, Culex eduardoi, Culex chidesteri, Uranotaenia lowii, Uranotaenia pulcherrima, Anopheles neomaculipalpus, Anopheles triannulatus, Anopheles albitarsis, Uranotaenia apicalis, Mansonia humeralis and Aedeomyia squamipennis). Principal component analysis indicates that the size of the larval habitats and the presence of aquatic vegetation are the main characteristics that explain the variation among different species. In contrast, water permanence is second in importance. Water temperature, pH and the type of larval habitat are less important in explaining the clustering of species.

Wetland hydrology and tree distribution of the Apalachicola River flood plain, Florida

USGS Publications Warehouse

Leitman, H.M.; Sohm, J.E.; Franklin, M.A.

1982-01-01

The Apalachicola River is part of a 50,800-square-kilometer drainage basin in northwest Florida, Alabama, and Georgia. The river is formed by the confluence of the Chattahoochee and Flint Rivers at Jim Woodruff Dam and flows 171 kilometers to Apalachicola Bay in the Gulf of Mexico. Its flood plain supports 450 square kilometers of bottom-land hardwood and tupelco-cypress forests. The most common trees, constituting 62 percent of the total basal area, were five wet-site species; water tupelo, Ogeeche tupelo, baldcypress, Carolina ash, and swamp tupelo. Other common species were sweetgum, overcup oak, planertree, green ash, water hickory, sugarberry, and diamond-leaf oak. Five forest types were defined based on species predominance by basal area. Biomass increased downstream and was greatest in forests growing on permanently saturated soils. Water and tree relations varied with river location because range in water-level fluctuation and topographic relief in the flood plain diminished downstream. Heights of natural riverbank levees and size and distribution of breaks in levees had a major controlling effect on flood-plain hydrology. Depth of water, duration of inundation and saturation, and river location, but not water velocity, were very highly correlated with forest types. (USGS)

A meta-analysis of educational interventions designed to enhance cultural competence in professional nurses and nursing students.

PubMed

Gallagher, Ruth W; Polanin, Joshua R

2015-02-01

Increasing professional nurses' and nursing students cultural competence has been identified as one way to decrease the disparity of care for vulnerable and minority groups, but effectiveness of training programs to increase competence remains equivocal. The purpose of this project is to synthesize educational interventions designed to increase cultural competence in professional nurses and nursing students. A systematic review and meta-analysis was conducted to synthesize all existing studies on increasing cultural competence. A comprehensive search and screen procedures was conducted to locate all cultural competence interventions implemented with professional nurses and nursing students. Two independent researchers screened and coded the included studies. Effect sizes were calculated for each study and a random-effects meta-analysis was conducted. A total of 25 studies were included in the review. Two independent syntheses were conducted given the disparate nature of the effect size metrics. For the synthesis of treatment-control designed studies, the results revealed a non-statistically significant increase in cultural competence (g¯=.38, 95% CI: -.05, .79, p=.08). Moderator analyses indicated significant variation as a function of the measurements, participant types, and funding source. The pretest-posttest effect size synthesis revealed a significant increase in overall cultural competence (g¯=.45, 95% CI: .24, .66, p<.01). Moderator analyses indicated, however, that the effect sizes varied as functions of the measurement, funding source, and publication type. Interventions to increase cultural competence have shown varied effectiveness. Greater research is required to improve these interventions and promote cultural competence. Copyright © 2014 Elsevier Ltd. All rights reserved.

Airborne characterization of aerosols over the contiguous United States during the SEAC4RS and DC3 campaigns: an in situ light scattering perspective

NASA Astrophysics Data System (ADS)

Espinosa, R.; Remer, L.; Puthukkudy, A.; Orozco, D.; Dubovik, O.; Martins, J. V.

2017-12-01

Models used to estimate climate change and interpret remote sensing observations must make assumptions regarding aerosol radiation interactions. This presentation will summarize aerosol light scattering measurements made by the Polarized Imaging Nephelometer (PI-Neph) during the Studies of Emissions and Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys (SEAC4RS) and Deep Convective Clouds and Chemistry (DC3) experiments. The data presented includes direct measurements of phase function (P11) and polarized phase function (-P12/P11) as well as retrievals of size distribution, sphericity and complex refractive index made using the Generalized Retrieval of Aerosol and Surface Properties (GRASP). An aerosol classification scheme is developed to identify different aerosol types measured during the deployments, making use of ancillary data that includes gas tracers, chemical composition, aerodynamic particle size and geographic location. Principal component analysis (PCA) is then used to reduce the dimensionality of the multi-angle PI-Neph scattering data and a strong link between the PCA scores and the ancillary classification results is observed. The scattering differences that reliable distinguish the different aerosol types are found to be quite subtle and often rely on the relationships between many scattering angles simultaneously. This fact emphasis the value of multi-angle scattering measurements, as well as principal component analysis's ability to reveal the underlying patterns in these datasets. The parameters retrieved from the DC3 scattering data suggest the presence of a significant amount of dust in aerosols influenced by convective systems, with the quantity of dust correlating strongly with sampling location and the underlying surface features. All fine mode dominated aerosol types from SEAC4RS had remarkably similar retrieved properties, except for the real refractive index of the biomass burning cases, which was consistently elevated (n532=1.54) when compared to the other types (n532=1.50). This result suggests that climate and remote sensing models may often be able to capture the differences in optical properties between biomass burning and other fine mode aerosols by only adjusting the real refractive index of the particles.

49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2011 CFR

2011-10-01

.... A. Angular locations, diameters, key/keyway sizes, and any other interchangeability dimensions for... base in the bulb holder such as tabs, keys, keyways, surface, etc. III. Bulb Holder Interchangeability Dimensions and Tolerances. A. Mating angular locations, diameters, key/keyway sizes, any other...

49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2012 CFR

2012-10-01

.... A. Angular locations, diameters, key/keyway sizes, and any other interchangeability dimensions for... base in the bulb holder such as tabs, keys, keyways, surface, etc. III. Bulb Holder Interchangeability Dimensions and Tolerances. A. Mating angular locations, diameters, key/keyway sizes, any other...

7 CFR 1822.271 - Processing applications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... specific provisions of State law under which the applicant is organized; a copy of the applicant's articles... project. (i) Location and size of tract or tracts to be bought and/or developed. (ii) Number and size of... contribution to the project. (8) A map showing the location of and other supporting information on neighborhood...

7 CFR 1822.271 - Processing applications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... specific provisions of State law under which the applicant is organized; a copy of the applicant's articles... project. (i) Location and size of tract or tracts to be bought and/or developed. (ii) Number and size of... contribution to the project. (8) A map showing the location of and other supporting information on neighborhood...

7 CFR 1822.271 - Processing applications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... specific provisions of State law under which the applicant is organized; a copy of the applicant's articles... project. (i) Location and size of tract or tracts to be bought and/or developed. (ii) Number and size of... contribution to the project. (8) A map showing the location of and other supporting information on neighborhood...

7 CFR 1822.271 - Processing applications.

Code of Federal Regulations, 2014 CFR

2014-01-01

... specific provisions of State law under which the applicant is organized; a copy of the applicant's articles... project. (i) Location and size of tract or tracts to be bought and/or developed. (ii) Number and size of... contribution to the project. (8) A map showing the location of and other supporting information on neighborhood...

Suspended Sediment Character in the Tidal Mekong River: Observations from LISST Profiling

NASA Astrophysics Data System (ADS)

Di Leonardo, D. R.; Allison, M. A.

2016-02-01

In two recent cooperative field campaigns, teams of researchers from the US and Vietnam collected hydrological and sedimentological data during a low flow season and a high flow season on the lower 100 km of the Song Hau distributary of the Mekong River. The objective of this study is to describe the forcing controls (e.g., tidal and riverine flow, water column stratification, resuspension) on suspended sediment grain size (e.g. mass, volume, granulometry, degree of flocculation) as measured by a Sequoia Scientific LISST 100X mounted on a profiling CTD. LISST (Type C, 2.5-500 µm size range) casts were collected at five transects in the Song Hau distributary. Four transects were located in the Dinh An and the Tran De channels immediately above the ocean interface with one additional transect located above the channel bifurcation, 40 km from the river mouth. Casts were collected at multiple stations across each channel transect for 12 hour and 24 hour continuous periods. Stationary ADCP data was collected during each 5-15 minute cast period and used to characterize shear stress. Preliminary results from the LISST suggest that the majority of suspended sediment is in the silt and very fine sand range. Increasing concentrations of all size fractions towards the bed suggests a local sediment source. Bimodal grain size distributions, with the coarser peak in the 150 µm to 250 µm range, are observed frequently, especially in the low discharge study. Grain size frequencies from the high discharge study tend to be more often unimodal. While there was effectively no salinity observed during the October 2014 high flow season, a maximum of 25.8 PSU was observed in the March 2015 low flow season. These results suggest that flocculation is an important process in the Mekong River, particularly during periods of higher salinity.

Self-diagnosis of damage in fibrous composites using electrical resistance measurements

NASA Astrophysics Data System (ADS)

Kang, Ji Ho; Paty, Spandana; Kim, Ran Y.; Tandon, G. P.

2006-03-01

The objective of this research was to develop a practical integrated approach using extracted features from electrical resistance measurements and coupled electromechanical models of damage, for in situ damage detection and sensing in carbon fiber reinforced plastic (CFRP) composite structures. To achieve this objective, we introduced specific known damage (in terms of type, size, and location) into CFRP laminates and established quantitative relationships with the electrical resistance measurements. For processing of numerous measurement data, an autonomous data acquisition system was devised. We also established a specimen preparation procedure and a method for electrode setup. Coupon and panel CFRP laminate specimens with several known damage were tested and post-processed with the measurement data. Coupon specimens with various sizes of artificial delaminations obtained by inserting Teflon film were manufactured and the resistance was measured. The measurement results showed that increase of delamination size led to increase of resistance implying that it is possible to sense the existence and size of delamination. Encouraged by the results of coupon specimens, we implemented the measurement system on panel specimens. Three different quasi-isotropic panels were designed and manufactured: a panel with artificial delamination by inserting Teflon film at the midplane, a panel with artificial delamination by inserting Teflon film between the second and third plies from the surface, and an undamaged panel. The first two panels were designed to determine the feasibility of detecting delamination using the developed measurement system. The third panel had no damage at first, and then three different sizes of holes were drilled at a chosen location. Panels were prepared using the established procedures with six electrode connections on each side making a total of twenty-four electrode connections for a panel. All possible pairs of electrodes were scanned and the resistance was measured for each pair. The measurement results showed the possibility of the established measurement system for an in-situ damage detection method for CFRP composite structures.

Analyzing ROC curves using the effective set-size model

NASA Astrophysics Data System (ADS)

Samuelson, Frank W.; Abbey, Craig K.; He, Xin

2018-03-01

The Effective Set-Size model has been used to describe uncertainty in various signal detection experiments. The model regards images as if they were an effective number (M*) of searchable locations, where the observer treats each location as a location-known-exactly detection task with signals having average detectability d'. The model assumes a rational observer behaves as if he searches an effective number of independent locations and follows signal detection theory at each location. Thus the location-known-exactly detectability (d') and the effective number of independent locations M* fully characterize search performance. In this model the image rating in a single-response task is assumed to be the maximum response that the observer would assign to these many locations. The model has been used by a number of other researchers, and is well corroborated. We examine this model as a way of differentiating imaging tasks that radiologists perform. Tasks involving more searching or location uncertainty may have higher estimated M* values. In this work we applied the Effective Set-Size model to a number of medical imaging data sets. The data sets include radiologists reading screening and diagnostic mammography with and without computer-aided diagnosis (CAD), and breast tomosynthesis. We developed an algorithm to fit the model parameters using two-sample maximum-likelihood ordinal regression, similar to the classic bi-normal model. The resulting model ROC curves are rational and fit the observed data well. We find that the distributions of M* and d' differ significantly among these data sets, and differ between pairs of imaging systems within studies. For example, on average tomosynthesis increased readers' d' values, while CAD reduced the M* parameters. We demonstrate that the model parameters M* and d' are correlated. We conclude that the Effective Set-Size model may be a useful way of differentiating location uncertainty from the diagnostic uncertainty in medical imaging tasks.

Proportion of various types of thyroid disorders among newborns with congenital hypothyroidism and normally located gland: a regional cohort study.

PubMed

Gaudino, Rossella; Garel, Catherine; Czernichow, Paul; Léger, Juliane

2005-04-01

To determine the proportion of the various types of thyroid disorders among newborns detected by the neonatal TSH screening programme, with a normally located thyroid gland. Patients and methods Of the 882 575 infants screened in our centre between 1981 and 2002, 85 infants with a normally located gland had persistent elevation of serum TSH values (an incidence of 1/10 383). Six of these 85 patients were lost to follow-up and were therefore excluded from the study. During follow-up, patients were classified as having permanent or transient hypothyroidism. Among the 79 patients included in the study, transient (n = 30, 38% of cases) and permanent (n = 49, 62% of cases) congenital hypothyroidism (CH) was demonstrated during the follow-up at the age of 0.7 +/- 0.6 years and 2.6 +/- 1.8 years (P < 0.0001), respectively. The proportion of premature births was significantly higher in the group with transient CH (57%) than in the group with permanent CH (2%) (P < 0.0001). A history of iatrogenic iodine overload was identified during the neonatal period in 69% of transient cases. Among permanent CH cases (n = 49), patients were classified as having a goitre (n = 27, 55% of cases), a normal sized and shaped thyroid gland (n = 14, 29% of cases) or a hypoplastic gland (n = 8, 16% of cases). The latter patients demonstrated global thyroid hypoplasia (n = 3), a right hemithyroid (n = 2), hypoplasia of the left lobe (n = 2), or asymmetry in the location of the two lobes (n = 1). Patients with a normal sized and shaped thyroid gland showed a significantly less severe form of hypothyroidism than those with a goitre or a hypoplastic thyroid gland (P < 0.0002). Among permanent CH cases, those with a goitre (n = 27) had an iodine organification defect (n = 10), Pendred syndrome (n = 1), a defect of thyroglobulin synthesis (n = 8), or a defect of sodium iodine symporter (n = 1), and in seven patients no aetiology could be determined. Among permanent cases with a normal sized and shaped thyroid gland (n = 14), a specific aetiology was found in only one patient (pseudohypoparathyroidism) and two patients had Down's syndrome. Among those with a globally hypoplastic gland, a TSH receptor gene mutation was found in two patients. A precise description of the phenotype can enhance our understanding of various forms of neonatal hypothyroidism as well as their prevalence and management. It also helps to identify cases of congenital hypothyroidism of unknown aetiology, which will need to be investigated in collaboration with molecular biologists.

46 CFR 194.10-5 - Type and location.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Type and location. 194.10-5 Section 194.10-5 Shipping..., AND CONTROL OF EXPLOSIVES AND OTHER HAZARDOUS MATERIALS Magazines § 194.10-5 Type and location. (a.... (b) Magazine vans. (1) Magazine vans may be installed on deck in a location protected from boarding...

Socio-economic differences in outdoor food advertising in a city in Northern England.

PubMed

Adams, Jean; Ganiti, Ellie; White, Martin

2011-06-01

To explore differences in the prevalence of outdoor food advertising, and the type and nutritional content of advertised foods, according to an area-based marker of socio-economic position (SEP) in a city in Northern England. All outdoor advertisements in the city were identified during October-December 2009, their size (in m2) estimated and their location determined using a global positioning system device. Advertisements were classified as food or non-food. Food advertisements were classified into one of six food categories. Information on the nutritional content of advertised foods was obtained from packaging and manufacturer's websites. An area-based marker of SEP was assigned using the location of each advertisement, grouped into three affluence tertiles for analysis. A city in Northern England. None. In all, 1371 advertisements were identified; 211 (15 %) of these were for food. The advertisements covered 6765 m2, of which 1326 m2 (20 %) was for food. Total advertising and food advertising space was largest in the least affluent tertile. There was little evidence of socio-economic trends in the type or nutritional content of advertised foods. Despite an absence of socio-economic differences in the type and nutritional content of advertised foods, there were socio-economic differences in food advertising space. There may also be socio-economic differences in exposure to outdoor food advertising.

King County Nearshore Habitat Mapping Data Report: Picnic Point to Shilshole Bay Marina

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woodruff, Dana L.; Farley, Paul J.; Borde, Amy B.

2000-12-31

The objective of this study is to provide accurate, georeferenced maps of benthic habitats to assist in the siting of a new wastewater treatment plant outfall and the assessment of habitats of endangered, threatened, and economically important species. The mapping was conducted in the fall of 1999 using two complementary techniques: side-scan sonar and underwater videography. Products derived from these techniques include geographic information system (GIS) compatible polygon data of substrate type and vegetation cover, including eelgrass and kelp. Additional GIS overlays include underwater video track line data of total macroalgae, selected macroalgal species, fish, and macroinvertebrates. The combined toolsmore » of geo-referenced side-scan sonar and underwater video is a powerful technique for assessing and mapping of nearshore habitat in Puget Sound. Side-scan sonar offers the ability to map eelgrass with high spatial accuracy and resolution, and provides information on patch size, shape, and coverage. It also provides information on substrate change and location of specific targets (e.g., piers, docks, pilings, large boulders, debris piles). The addition of underwater video is a complementary tool providing both groundtruthing for the sonar and additional information on macro fauna and flora. As a groundtruthing technique, the video was able to confirm differences between substrate types, as well as detect subtle spatial changes in substrate. It also verified information related to eelgrass, including the density classification categories and the type of substrate associated with eelgrass, which could not be determined easily with side- scan sonar. Video is also a powerful tool for mapping the location of macroalgae, (including kelp and Ulva), fish and macroinvertebrates. The ability to geo-locate these resources in their functional habitat provides an added layer of information and analytical potential.« less

Accuracy evaluation of distance inverse square law in determining virtual electron source location in Siemens Primus linac.

PubMed

Douk, Hamid Shafaei; Aghamiri, Mahmoud Reza; Ghorbani, Mahdi; Farhood, Bagher; Bakhshandeh, Mohsen; Hemmati, Hamid Reza

2018-01-01

The aim of this study is to evaluate the accuracy of the inverse square law (ISL) method for determining location of virtual electron source ( S Vir ) in Siemens Primus linac. So far, different experimental methods have presented for determining virtual and effective electron source location such as Full Width at Half Maximum (FWHM), Multiple Coulomb Scattering (MCS), and Multi Pinhole Camera (MPC) and Inverse Square Law (ISL) methods. Among these methods, Inverse Square Law is the most common used method. Firstly, Siemens Primus linac was simulated using MCNPX Monte Carlo code. Then, by using dose profiles obtained from the Monte Carlo simulations, the location of S Vir was calculated for 5, 7, 8, 10, 12 and 14 MeV electron energies and 10 cm × 10 cm, 15 cm × 15 cm, 20 cm × 20 cm and 25 cm × 25 cm field sizes. Additionally, the location of S Vir was obtained by the ISL method for the mentioned electron energies and field sizes. Finally, the values obtained by the ISL method were compared to the values resulted from Monte Carlo simulation. The findings indicate that the calculated S Vir values depend on beam energy and field size. For a specific energy, with increase of field size, the distance of S Vir increases for most cases. Furthermore, for a special applicator, with increase of electron energy, the distance of S Vir increases for most cases. The variation of S Vir values versus change of field size in a certain energy is more than the variation of S Vir values versus change of electron energy in a certain field size. According to the results, it is concluded that the ISL method can be considered as a good method for calculation of S Vir location in higher electron energies (14 MeV).

Concrete Condition Assessment Using Impact-Echo Method and Extreme Learning Machines

PubMed Central

Zhang, Jing-Kui; Yan, Weizhong; Cui, De-Mi

2016-01-01

The impact-echo (IE) method is a popular non-destructive testing (NDT) technique widely used for measuring the thickness of plate-like structures and for detecting certain defects inside concrete elements or structures. However, the IE method is not effective for full condition assessment (i.e., defect detection, defect diagnosis, defect sizing and location), because the simple frequency spectrum analysis involved in the existing IE method is not sufficient to capture the IE signal patterns associated with different conditions. In this paper, we attempt to enhance the IE technique and enable it for full condition assessment of concrete elements by introducing advanced machine learning techniques for performing comprehensive analysis and pattern recognition of IE signals. Specifically, we use wavelet decomposition for extracting signatures or features out of the raw IE signals and apply extreme learning machine, one of the recently developed machine learning techniques, as classification models for full condition assessment. To validate the capabilities of the proposed method, we build a number of specimens with various types, sizes, and locations of defects and perform IE testing on these specimens in a lab environment. Based on analysis of the collected IE signals using the proposed machine learning based IE method, we demonstrate that the proposed method is effective in performing full condition assessment of concrete elements or structures. PMID:27023563

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ballering, Nicholas P.; Rieke, George H.; Gáspár, András, E-mail: ballerin@email.arizona.edu

Observations of debris disks allow for the study of planetary systems, even where planets have not been detected. However, debris disks are often only characterized by unresolved infrared excesses that resemble featureless blackbodies, and the location of the emitting dust is uncertain due to a degeneracy with the dust grain properties. Here, we characterize the Spitzer Infrared Spectrograph spectra of 22 debris disks exhibiting 10 μm silicate emission features. Such features arise from small warm dust grains, and their presence can significantly constrain the orbital location of the emitting debris. We find that these features can be explained by themore » presence of an additional dust component in the terrestrial zones of the planetary systems, i.e., an exozodiacal belt. Aside from possessing exozodiacal dust, these debris disks are not particularly unique; their minimum grain sizes are consistent with the blowout sizes of their systems, and their brightnesses are comparable to those of featureless warm debris disks. These disks are in systems of a range of ages, though the older systems with features are found only around A-type stars. The features in young systems may be signatures of terrestrial planet formation. Analyzing the spectra of unresolved debris disks with emission features may be one of the simplest and most accessible ways to study the terrestrial regions of planetary systems.« less

Coil geometry effects on scanning single-coil magnetic induction tomography

NASA Astrophysics Data System (ADS)

Feldkamp, Joe R.; Quirk, Stephen

2017-09-01

Alternative coil designs for single coil magnetic induction tomography are considered in this work, with the intention of improving upon the standard design used previously. In particular, we note that the blind spot associated with this coil type, a portion of space along its axis where eddy current generation can be very weak, has an important effect on performance. The seven designs tested here vary considerably in the size of their blind spot. To provide the most discerning test possible, we use laboratory phantoms containing feature dimensions similar to blind spot size. Furthermore, conductivity contrasts are set higher than what would occur naturally in biological systems, which has the effect of weakening eddy current generation at coil locations that straddle the border between high and low conductivity features. Image reconstruction results for the various coils show that coils with smaller blind spots give markedly better performance, though improvements in signal-to-noise ratio could alter that conclusion.

Limitation of Cell Adhesion by the Elasticity of the Extracellular Matrix

PubMed Central

Nicolas, Alice; Safran, Samuel. A.

2006-01-01

Cell/matrix adhesions are modulated by cytoskeletal or external stresses and adapt to the mechanical properties of the extracellular matrix. We propose that this mechanosensitivity arises from the activation of a mechanosensor located within the adhesion itself. We show that this mechanism accounts for the observed directional growth of focal adhesions and the reduction or even cessation of their growth when cells adhere to a soft extracellular matrix. We predict quantitatively that both the elasticity and the thickness of the matrix play a key role in the dynamics of focal adhesions. Two different types of dynamics are expected depending on whether the thickness of the matrix is of order of or much larger than the adhesion size. In the latter situation, we predict that the adhesion region reaches a saturation size that can be tuned by the mechanical properties of the matrix. PMID:16581840

Green Synthesis of Ag-Cu Nanoalloys Using Opuntia ficus- indica

NASA Astrophysics Data System (ADS)

Rocha-Rocha, O.; Cortez-Valadez, M.; Hernández-Martínez, A. R.; Gámez-Corrales, R.; Alvarez, Ramón A. B.; Britto-Hurtado, R.; Delgado-Beleño, Y.; Martinez-Nuñez, C. E.; Pérez-Rodríguez, A.; Arizpe-Chávez, H.; Flores-Acosta, M.

2017-02-01

Bimetallic Ag/Cu nanoparticles have been obtained by green synthesis using Opuntia ficus- indica plant extract. Two synthesis methods were applied to obtain nanoparticles with core-shell and Janus morphologies by reversing the order of precursors. Transmission electronic microscopy revealed size of 10 nm and 20 nm for the core-shell and Janus nanoparticles, respectively. Other small particles with size of up to 2 nm were also observed. Absorption bands attributed to surface plasmon resonance were detected at 440 nm and 500 nm for the core-shell and Janus nanoparticles, respectively. Density functional theory predicted a breathing mode type (BMT) located at low wavenumber due to small, low-energy clusters of (AgCu) n with n = 2 to 9, showing a certain correlation with the experimental one (at 220 cm-1). The dependence of the BMT on the number of atoms constituting the cluster is also studied.

Relationship between the size of a camphor-driven rotor and its angular velocity.

PubMed

Koyano, Yuki; Gryciuk, Marian; Skrobanska, Paulina; Malecki, Maciej; Sumino, Yutaka; Kitahata, Hiroyuki; Gorecki, Jerzy

2017-07-01

We consider a rotor made of two camphor disks glued below the ends of a plastic stripe. The disks are floating on a water surface and the plastic stripe does not touch the surface. The system can rotate around a vertical axis located at the center of the stripe. The disks dissipate camphor molecules. The driving momentum comes from the nonuniformity of surface tension resulting from inhomogeneous surface concentration of camphor molecules around the disks. We investigate the stationary angular velocity as a function of rotor radius ℓ. For large ℓ the angular velocity decreases for increasing ℓ. At a specific value of ℓ the angular velocity reaches its maximum and, for short ℓ it rapidly decreases. Such behavior is confirmed by a simple numerical model. The model also predicts that there is a critical rotor size below which it does not rotate. Within the introduced model we analyze the type of this bifurcation.

Development of composite calibration standard for quantitative NDE by ultrasound and thermography

NASA Astrophysics Data System (ADS)

Dayal, Vinay; Benedict, Zach G.; Bhatnagar, Nishtha; Harper, Adam G.

2018-04-01

Inspection of aircraft components for damage utilizing ultrasonic Non-Destructive Evaluation (NDE) is a time intensive endeavor. Additional time spent during aircraft inspections translates to added cost to the company performing them, and as such, reducing this expenditure is of great importance. There is also great variance in the calibration samples from one entity to another due to a lack of a common calibration set. By characterizing damage types, we can condense the required calibration sets and reduce the time required to perform calibration while also providing procedures for the fabrication of these standard sets. We present here our effort to fabricate composite samples with known defects and quantify the size and location of defects, such as delaminations, and impact damage. Ultrasonic and Thermographic images are digitally enhanced to accurately measure the damage size. Ultrasonic NDE is compared with thermography.

Characterization of sintered SiC by using NDE

NASA Technical Reports Server (NTRS)

Baaklini, George Y.

1988-01-01

Capabilities of projection microfocus X-radiography and of ultrasonic velocity and attenuation for characterizing silicon carbide specimens were assessed. Silicon carbide batches covered a range of densities and different microstructural characteristics. Room-temperature, four-point flexural strength tests were conducted. Fractography was used to identify types, sizes, and locations of fracture origins. Fracture toughness values were calculated from fracture strength and flaw characterization data. Detection capabilities of radiography for fracture-causing flaws were evaluated. Applicability of ultrasonics for verifying material strength and toughness was examined. Radiography proved useful in detecting high-density inclusions and isolated voids, but failed in detecting surface and subsurface agglomerates and large grains as fracture origins. Ultrasonic velocity dependency on density was evident. Attenuation dependency on density and mean pore size was clearly demonstrated. Understanding attenuation as a function of toughness was limited by shortcomings in K sub IC determination.

Endogenous Life Cycle of Eimeria melanomytis (Apicomplexa: Eimeriidae) from the Dusky Rice Rat, Melanomys caliginosus (Rodentia: Cricetidae: Sigmodontinae) in Costa Rica.

PubMed

Chinchilla, Misael; Valerio, Idalia; Sánchez, Ronald; Duszynski, Donald W

2017-02-01

Endogenous stages of the life cycle of Eimeria melanomytis, infecting the peripheral epithelial cells of villi of the small intestine of experimentally infected young dusky rice rats, Melanomys caliginosus , were studied. Giemsa-stained mucosal scrapings and histological sections were examined for all the stages. Eimeria melanomytis has 3 generations of meronts (M), different in size, shape, and number of merozoites (m); and in size, shape, and location of the nuclei within the cytoplasm of the meronts. The 3 meront types, M 1 -M 3 , respectively, had 11-14 (m 1 ), 7-10 (m 2 ), and 20-30 (m 3 ) merozoites. Macrogametocytes and microgametocytes, as well as macrogametes and microgametes, complete the sexual cycle forming the unsporulated oocysts. This parasite's endogenous development produced severe intestinal lesions in experimentally infected dusky rice rats.

Creation of nano eye-drops and effective drug delivery to the interior of the eye

NASA Astrophysics Data System (ADS)

Ikuta, Yoshikazu; Aoyagi, Shigenobu; Tanaka, Yuji; Sato, Kota; Inada, Satoshi; Koseki, Yoshitaka; Onodera, Tsunenobu; Oikawa, Hidetoshi; Kasai, Hitoshi

2017-03-01

Nano eye-drops are a new type of ophthalmic treatment with increased potency and reduced side effects. Compounds in conventional eye-drops barely penetrate into the eye because the cornea, located at the surface of eye, has a strong barrier function for preventing invasion of hydrophilic or large-sized materials from the outside. In this work, we describe the utility of nano eye-drops utilising brinzolamide, a commercially available glaucoma treatment drug, as a target compound. Fabrication of the nanoparticles of brinzolamide prodrug increases the eye penetration rate and results in high drug efficacy, compared with that of commercially available brinzolamide eye-drops formulated as micro-sized structures. In addition, the resulting nano eye-drops were not toxic to the corneal epithelium after repeated administration for 1 week. The nano eye-drops may have applications as a next-generation ophthalmic treatment.

Does high location and thickness of the Wrisberg ligament affect discoid lateral meniscus tear type based on peripheral detachment?

PubMed

Ahn, Jin Hwan; Wang, Joon Ho; Kim, Dong Uk; Lee, Do Kyung; Kim, Jun Ho

2017-12-01

The aim of this study was to evaluate the relationship between discoid lateral meniscus (DLM) types based on peripheral detachment and anatomic features of Wrisberg ligament (WL) such as location and thickness based on magnetic resonance image (MRI). A total of 322 knees in 292 patients were reviewed. Patients were divided into four DLM types according to peripheral detachment: no shift (type 1), anterocentral shift (type 2), posterocentral shift (type 3) and central shift (type 4). We reviewed all MRI concentrating on the presence, location (high or low location), running angle, thickness of WL, and WL/posterior cruciate ligament (PCL) thickness ratio. The relationship between DLM types and anatomic features of WL were analyzed using one-way analysis of variance and chi-square test. According to DLM types based on peripheral detachment, 149 knees were type 1, 38 were type 2, 79 were type 3, and 56 were type 4. Among the 322 knees, 302 (93.8%) had WL on MRI. In DLM patients, type 3 showed a statistically significant (P<0.001) relationship with high location of WL. In addition, type 3 had significantly larger (P<0.0001) running angle of WL, thicker (P<0.0001) WL, and higher (P<0.0001) WL/PCL ratio compared to other types. A high location and thick WL are related to posterocentral shift type of DLM based on peripheral detachment. Based on our results, the high location and thick WL might provide information to surgeons in predicting the direction of peripheral detachment in symptomatic DLM patients. Copyright © 2017 Elsevier B.V. All rights reserved.

Statistical properties of interval mapping methods on quantitative trait loci location: impact on QTL/eQTL analyses

PubMed Central

2012-01-01

Background Quantitative trait loci (QTL) detection on a huge amount of phenotypes, like eQTL detection on transcriptomic data, can be dramatically impaired by the statistical properties of interval mapping methods. One of these major outcomes is the high number of QTL detected at marker locations. The present study aims at identifying and specifying the sources of this bias, in particular in the case of analysis of data issued from outbred populations. Analytical developments were carried out in a backcross situation in order to specify the bias and to propose an algorithm to control it. The outbred population context was studied through simulated data sets in a wide range of situations. The likelihood ratio test was firstly analyzed under the "one QTL" hypothesis in a backcross population. Designs of sib families were then simulated and analyzed using the QTL Map software. On the basis of the theoretical results in backcross, parameters such as the population size, the density of the genetic map, the QTL effect and the true location of the QTL, were taken into account under the "no QTL" and the "one QTL" hypotheses. A combination of two non parametric tests - the Kolmogorov-Smirnov test and the Mann-Whitney-Wilcoxon test - was used in order to identify the parameters that affected the bias and to specify how much they influenced the estimation of QTL location. Results A theoretical expression of the bias of the estimated QTL location was obtained for a backcross type population. We demonstrated a common source of bias under the "no QTL" and the "one QTL" hypotheses and qualified the possible influence of several parameters. Simulation studies confirmed that the bias exists in outbred populations under both the hypotheses of "no QTL" and "one QTL" on a linkage group. The QTL location was systematically closer to marker locations than expected, particularly in the case of low QTL effect, small population size or low density of markers, i.e. designs with low power. Practical recommendations for experimental designs for QTL detection in outbred populations are given on the basis of this bias quantification. Furthermore, an original algorithm is proposed to adjust the location of a QTL, obtained with interval mapping, which co located with a marker. Conclusions Therefore, one should be attentive when one QTL is mapped at the location of one marker, especially under low power conditions. PMID:22520935

Raccoon spatial requirements and multi-scale habitat selection within an intensively managed central Appalachian forest

USGS Publications Warehouse

Owen, Sheldon F.; Berl, Jacob L.; Edwards, John W.; Ford, W. Mark; Wood, Petra Bohall

2015-01-01

We studied a raccoon (Procyon lotor) population within a managed central Appalachian hardwood forest in West Virginia to investigate the effects of intensive forest management on raccoon spatial requirements and habitat selection. Raccoon home-range (95% utilization distribution) and core-area (50% utilization distribution) size differed between sexes with males maintaining larger (2×) home ranges and core areas than females. Home-range and core-area size did not differ between seasons for either sex. We used compositional analysis to quantify raccoon selection of six different habitat types at multiple spatial scales. Raccoons selected riparian corridors (riparian management zones [RMZ]) and intact forests (> 70 y old) at the core-area spatial scale. RMZs likely were used by raccoons because they provided abundant denning resources (i.e., large-diameter trees) as well as access to water. Habitat composition associated with raccoon foraging locations indicated selection for intact forests, riparian areas, and regenerating harvest (stands <10 y old). Although raccoons were able to utilize multiple habitat types for foraging resources, a selection of intact forest and RMZs at multiple spatial scales indicates the need of mature forest (with large-diameter trees) for this species in managed forests in the central Appalachians.

Uterine leiomyomata and fecundability in the Right from the Start study.

PubMed

Johnson, Gayle; MacLehose, Richard F; Baird, Donna D; Laughlin-Tommaso, Shannon K; Hartmann, Katherine E

2012-10-01

Previous research suggests the removal of uterine leiomyomata may improve ability to conceive. Most of this previous research was conducted in infertility clinics. We investigated the association between leiomyoma characteristics on time to pregnancy among women enrolled from the general population. We enrolled a cohort study of women in early pregnancy. Participants retrospectively reported their time to conception. Leiomyomata characteristics were determined by first-trimester ultrasound. We used discrete time hazard models to estimate the effects of uterine leiomyomata on time to pregnancy. In this population of 3000 women, 11% (324) with one or more leiomyomata, we found no association between leiomyomata presence, type, location, segment or size on time to pregnancy. These results suggest that leiomyomata have little effect on time to pregnancy in this cohort of women. The study excluded women who had been treated for infertility, and this may have resulted in underestimation of the association. However, differences between our study and previous studies in specialty clinics may be, in part, attributable to differences between our community-recruited population of women and women receiving fertility care, as well as difference in leiomyomata size or type in women having myomectomies to treat infertility.

CpG island methylator phenotype and its association with malignancy in sporadic duodenal adenomas.

PubMed

Sun, Lifeng; Guzzetta, Angela A; Fu, Tao; Chen, Jinming; Jeschke, Jana; Kwak, Ruby; Vatapalli, Rajita; Baylin, Stephen B; Iacobuzio-Donahue, Christine A; Wolfgang, Christopher L; Ahuja, Nita

2014-05-01

CpG island methylator phenotype (CIMP) has been found in multiple precancerous and cancerous lesions, including colorectal adenomas, colorectal cancers, and duodenal adenocarcinomas. There are no reports in the literature of a relationship between CIMP status and clinicopathologic features of sporadic duodenal adenomas. This study sought to elucidate the role of methylation in duodenal adenomas and correlate it with KRAS and BRAF mutations. CIMP+ (with more than 2 markers methylated) was seen in 33.3% of duodenal adenomas; 61% of these CIMP+ adenomas were CIMP-high (with more than 3 markers methylated). Furthermore, CIMP+ status significantly correlated with older age of patients, larger size and villous type of tumor, coexistent dysplasia and periampullary location. MLH1 methylation was seen in 11.1% of duodenal adenomas and was significantly associated with CIMP+ tumors, while p16 methylation was an infrequent event. KRAS mutations were frequent and seen in 26.3% of adenomas; however, no BRAF mutations were detected. Furthermore, CIMP-high status was associated with larger size and villous type of tumor and race (non-white). These results suggest that CIMP+ duodenal adenomas may have a higher risk for developing malignancy and may require more aggressive management and surveillance.

CpG island methylator phenotype and its association with malignancy in sporadic duodenal adenomas

PubMed Central

Sun, Lifeng; Guzzetta, Angela A; Fu, Tao; Chen, Jinming; Jeschke, Jana; Kwak, Ruby; Vatapalli, Rajita; Baylin, Stephen B; Iacobuzio-Donahue, Christine A; Wolfgang, Christopher L; Ahuja, Nita

2014-01-01

CpG island methylator phenotype (CIMP) has been found in multiple precancerous and cancerous lesions, including colorectal adenomas, colorectal cancers, and duodenal adenocarcinomas. There are no reports in the literature of a relationship between CIMP status and clinicopathologic features of sporadic duodenal adenomas. This study sought to elucidate the role of methylation in duodenal adenomas and correlate it with KRAS and BRAF mutations. CIMP+ (with more than 2 markers methylated) was seen in 33.3% of duodenal adenomas; 61% of these CIMP+ adenomas were CIMP-high (with more than 3 markers methylated). Furthermore, CIMP+ status significantly correlated with older age of patients, larger size and villous type of tumor, coexistent dysplasia and periampullary location. MLH1 methylation was seen in 11.1% of duodenal adenomas and was significantly associated with CIMP+ tumors, while p16 methylation was an infrequent event. KRAS mutations were frequent and seen in 26.3% of adenomas; however, no BRAF mutations were detected. Furthermore, CIMP-high status was associated with larger size and villous type of tumor and race (non-white). These results suggest that CIMP+ duodenal adenomas may have a higher risk for developing malignancy and may require more aggressive management and surveillance. PMID:24518818

17 CFR 232.308 - Type size and font; legibility.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Type size and font; legibility. 232.308 Section 232.308 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION... § 232.308 Type size and font; legibility. Provisions relating to type size, font and other legibility...

Isotopic signatures, foraging habitats and trophic relationships between fish and seasnakes on the coral reefs of New Caledonia

NASA Astrophysics Data System (ADS)

Brischoux, F.; Bonnet, X.; Cherel, Y.; Shine, R.

2011-03-01

A predator's species, sex and body size can influence the types of prey that it consumes, but why? Do such dietary divergences result from differences in foraging habitats, or reflect differential ability to locate, capture or ingest different types of prey? That question is difficult to answer if foraging occurs in places that preclude direct observation. In New Caledonia, amphibious sea kraits ( Laticauda laticaudata and L. saintgironsi) mostly eat eels—but the species consumed differ between snake species and vary with snake body size and sex. Because the snakes capture eels within crevices on the sea floor, it is not possible to observe snake foraging on any quantitative basis. We used stable isotopes to investigate habitat-divergence and ontogenetic shifts in feeding habits of sympatric species of sea kraits. Similarities in δ15 N (~10.5‰) values suggest that the two snake species occupy similar trophic levels in the coral-reef foodweb. However, δ13C values differed among the eight eel species consumed by snakes, as well as between the two snake species, and were linked to habitat types. Specifically, δ13C differed between soft- vs. hard-substrate eel species, and consistently differed between the soft-bottom forager L. laticaudata (~ -14.7‰) and the hard-bottom forager L. saintgironsi (~ -12.5‰). Differences in isotopic signatures within and between the two sea krait species and their prey were consistent with the hypothesis of habitat-based dietary divergence. Isotopic composition varied with body size within each of the snake species and varied with body size within some eel species, reflecting ontogenetic shifts in feeding habits of both the sea kraits and their prey. Our results support the findings of previous studies based on snake stomach contents, indicating that further studies could usefully expand these isotopic analyses to a broader range of trophic levels, fish species and spatial scales.

Productivity of tree swallows (Tachycineta bicolor) exposed to PCBs at the Kalamazoo River superfund site.

PubMed

Neigh, Arianne M; Zwiernik, Matthew J; MacCarroll, Monica A; Newsted, John L; Blankenship, Alan L; Jones, Paul D; Kay, Denise P; Giesy, John P

2006-03-01

A 123-km stretch of the Kalamazoo River in Michigan, was designated a Superfund site in 1990 due to historical releases of effluent containing polychlorinated biphenyl (PCB)-contaminated paper waste. Risk to bird species in the river ecosystem was evaluated using the tree swallow (Tachycineta bicolor) as a monitor for possible effects due to PCB exposure at two nesting locations, one in the Superfund site and one in an upstream reference location that is less contaminated with PCBs. In 2 of the 3 years of the study, clutch size at the contaminated location was 3.7 +/- 1.4 and 4.8 +/- 0.73 eggs per nest (mean +/- SD), which was significantly less than the clutch size at the reference location (5.0 +/- 1.1 and 5.3 +/- 1.1 eggs per nest). However, there were no statistically significant differences in fledging success, predicted brood size, predicted number of fledglings, or growth of nestlings between the Kalamazoo River Superfund site and an upstream reference location with lesser concentrations of PCBs in the sediments and riparian soils. Productivity and hatching success comparisons between these same sites were also not significantly different; however, the power of these conclusions was less (p < .10). The reduction in clutch size at the co-contaminated location could not be attributed to PCBs due to a number of confounding factors, including Co-cocontaminants, habitat structure, and food availability. Other reproductive parameters were not significantly impaired, and the size of the newly established colony at the Kalamazoo River Superfund site continued to grow over the period of the study. These site-specific observations, combined with multiple lines of evidence approach that considered results reported for the effects of both total PCBs and 2,3,7,8 tetrachlorodibenzo-p-dioxin equivalents (TEQ) on tree swallows at other locations, suggest that there were no significant population-level effects of PCBs on tree swallows at the Kalamazoo River Superfund site.

Survival, growth, and localization of epiphytic fitness mutants of pseudomonas syringae on leaves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beattie, G.A.; Lindow, S.E.

Among 82 epiphytic fitness mutants of a Pseudomonas syringae pv. syringae strain that were characterized in a previous study, 4 mutants were particularly intolerant of the stresses associated with dry leaf surfaces. These four mutants each exhibited distinctive behaviors when inoculated into and into plant leaves. For example, while non showed measurable growth on dry potato leaf surfaces, they grew to different population sizes in the intercellular space of bean leaves and on dry bean leaf surfaces, and one mutant appeared incapable of growth in both environments although it grew well on moist bean leaves. The presence of the parentalmore » strain did not influence the survival of the mutants immediately following exposure of leaves to dry, high-light incubation conditions, suggesting that the reduced survival of the mutants did not result from an inability to produce extracellular factors in planta. On moist bean leaves that were colonized by either a mutant or the wild type, the proportion of the total epiphytic population that was located in sizes protected from a surface sterilant was smaller for the mutants than for the wild type, indicating that the mutants were reduced in their ability to locate, multiply in, and/or survive in such protected sites. This reduced ability was only one of possible several factors contributing to the reduced epiphytic fitness of each mutant. Their reduced fitness was not specific to the host plant bean, since they also exhibited reduced fitness on the nonhost plant potato; the functions altered in these strains are thus of interest for their contribution to the general fitness of bacterial epiphytes. 52 refs., 6 figs., 1 tab.« less

Crater-based dating of geological units on Mars: methods and application for the new global geological map

USGS Publications Warehouse

Platz, Thomas; Michael, Gregory; Tanaka, Kenneth L.; Skinner, James A.; Fortezzo, Corey M.

2013-01-01

The new, post-Viking generation of Mars orbital imaging and topographical data provide significant higher-resolution details of surface morphologies, which induced a new effort to photo-geologically map the surface of Mars at 1:20,000,000 scale. Although from unit superposition relations a relative stratigraphical framework can be compiled, it was the ambition of this mapping project to provide absolute unit age constraints through crater statistics. In this study, the crater counting method is described in detail, starting with the selection of image data, type locations (both from the mapper’s and crater counter’s perspectives) and the identification of impact craters. We describe the criteria used to validate and analyse measured crater populations, and to derive and interpret crater model ages. We provide examples of how geological information about the unit’s resurfacing history can be retrieved from crater size–frequency distributions. Three cases illustrate short-, intermediate, and long-term resurfacing histories. In addition, we introduce an interpretation-independent visualisation of the crater resurfacing history that uses the reduction of the crater population in a given size range relative to the expected population given the observed crater density at larger sizes. From a set of potential type locations, 48 areas from 22 globally mapped units were deemed suitable for crater counting. Because resurfacing ages were derived from crater statistics, these secondary ages were used to define the unit age rather than the base age. Using the methods described herein, we modelled ages that are consistent with the interpreted stratigraphy. Our derived model ages allow age assignments to be included in unit names. We discuss the limitations of using the crater dating technique for global-scale geological mapping. Finally, we present recommendations for the documentation and presentation of crater statistics in publications.

Diagnostic accuracy of T stage of gastric cancer from the view point of application of laparoscopic proximal gastrectomy.

PubMed

Kouzu, Keita; Tsujimoto, Hironori; Hiraki, Shuichi; Nomura, Shinsuke; Yamamoto, Junji; Ueno, Hideki

2018-06-01

The preoperative diagnosis of T stage is important in selecting limited treatments, such as laparoscopic proximal gastrectomy (LPG), which lacks the ability to palpate the tumor. Therefore, the present study examined the accuracy of preoperative diagnosis of the depth of tumor invasion in early gastric cancer from the view point of the indication for LPG. A total of 193 patients with cT1 gastric cancer underwent LPG with gastrointestinal endoscopic examinations and a series of upper gastrointestinal radiographs. The patients with pT1 were classified into the correctly diagnosed group (163 patients, 84.5%), and those with pT2 or deeper were classified into the underestimated group (30 patients, 15.5%). Factors that were associated with underestimation of tumor depth were analyzed. Tumor size in the underestimated group was significantly larger; the lesions were more frequently located in the upper third of the stomach and were more histologically diffuse, scirrhous, with infiltrative growth, and more frequent lymphatic and venous invasion. For upper third lesions, in univariate analysis, histology (diffuse type) was associated with underestimation of tumor depth. Multivariate analysis found that tumor size (≥20 mm) and histology (diffuse type) were independently associated with underestimation of tumor depth. gastric cancer in the upper third of the stomach with diffuse type histology and >20 mm needs particular attention when considering the application of LPG.

Diagnostic accuracy of T stage of gastric cancer from the view point of application of laparoscopic proximal gastrectomy

PubMed Central

Kouzu, Keita; Tsujimoto, Hironori; Hiraki, Shuichi; Nomura, Shinsuke; Yamamoto, Junji; Ueno, Hideki

2018-01-01

The preoperative diagnosis of T stage is important in selecting limited treatments, such as laparoscopic proximal gastrectomy (LPG), which lacks the ability to palpate the tumor. Therefore, the present study examined the accuracy of preoperative diagnosis of the depth of tumor invasion in early gastric cancer from the view point of the indication for LPG. A total of 193 patients with cT1 gastric cancer underwent LPG with gastrointestinal endoscopic examinations and a series of upper gastrointestinal radiographs. The patients with pT1 were classified into the correctly diagnosed group (163 patients, 84.5%), and those with pT2 or deeper were classified into the underestimated group (30 patients, 15.5%). Factors that were associated with underestimation of tumor depth were analyzed. Tumor size in the underestimated group was significantly larger; the lesions were more frequently located in the upper third of the stomach and were more histologically diffuse, scirrhous, with infiltrative growth, and more frequent lymphatic and venous invasion. For upper third lesions, in univariate analysis, histology (diffuse type) was associated with underestimation of tumor depth. Multivariate analysis found that tumor size (≥20 mm) and histology (diffuse type) were independently associated with underestimation of tumor depth. gastric cancer in the upper third of the stomach with diffuse type histology and >20 mm needs particular attention when considering the application of LPG. PMID:29844908

Examine Middle School Students' Constructivist Environment Perceptions in Turkey: School Location and Class Size

ERIC Educational Resources Information Center

Yigit, Nevzat; Alpaslan, Muhammet Mustafa; Cinemre, Yasin; Balcin, Bilal

2017-01-01

This study aims to examine the middle school students' perceptions of the classroom learning environment in the science course in Turkey in terms of school location and class size. In the study the Assessing of Constructivist Learning Environment (ACLE) questionnaire was utilized to map students' perceptions of the classroom learning environment.…

49 CFR 236.560 - Contact element, mechanical trip type; location with respect to rail.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Contact element, mechanical trip type; location... Instructions; Locomotives § 236.560 Contact element, mechanical trip type; location with respect to rail. Contact element of automatic train stop device of the mechanical trip type shall be maintained at a height...

Putting to a bigger hole: Golf performance relates to perceived size

PubMed Central

Witt, Jessica K.; Linkenauger, Sally A.; Bakdash, Jonathan Z.; Proffitt, Dennis R.

2011-01-01

When engaged in a skilled behaviour such as occurs in sports, people's perceptions relate optical information to their performance. In current research we demonstrate the effects of performance on size perception in golfers. We found golfers who played better judged the hole to be bigger than golfers who did not play as well (Study 1). In follow-up laboratory experiments, participants putted on a golf mat from a location near or far from the hole then judged the size of the hole. Participants who putted from the near location perceived the hole to be bigger than participants who putted from the far location. Our results demonstrate that perception is influenced by the perceiver's current ability to act effectively in the environment. PMID:18567258

Collector Size or Range Independence of SNR in Fixed-Focus Remote Raman Spectrometry.

PubMed

Hirschfeld, T

1974-07-01

When sensitivity allows, remote Raman spectrometers can be operated at a fixed focus with purely electronic (easily multiplexable) range gating. To keep the background small, the system etendue must be minimized. For a maximum range larger than the hyperfocal one, this is done by focusing the system at roughly twice the minimum range at which etendue matching is still required. Under these conditions the etendue varies as the fourth power of the collector diameter, causing the background shot noise to vary as its square. As the signal also varies with the same power, and background noise is usually limiting in this type instrument, the SNR becomes independent of the collector size. Below this minimum etendue-matched range, the transmission at the limiting aperture grows with the square of the range, canceling the inverse square loss of signal with range. The SNR is thus range independent below the minimum etendue matched range and collector size independent above it, with the location of transition being determined by the system etendue and collector diameter. The range of validity of these outrageousstatements is discussed.

Magnetic properties of graphene quantum dots

NASA Astrophysics Data System (ADS)

Espinosa-Ortega, T.; Luk'yanchuk, I. A.; Rubo, Y. G.

2013-05-01

Using the tight-binding approximation we calculated the diamagnetic susceptibility of graphene quantum dots (GQDs) of different geometrical shapes and characteristic sizes of 2-10 nm, when the magnetic properties are governed by the electron edge states. Two types of edge states can be discerned: the zero-energy states (ZESs), located exactly at the zero-energy Dirac point, and the dispersed edge states (DESs), with the energy close but not exactly equal to zero. DESs are responsible for a temperature-independent diamagnetic response, while ZESs provide a temperature-dependent spin paramagnetism. Hexagonal, circular, and randomly shaped GQDs contain mainly DESs, and, as a result, they are diamagnetic. The edge states of the triangular GQDs are of ZES type. These dots reveal the crossover between spin paramagnetism, dominating for small dots and at low temperatures, and orbital diamagnetism, dominating for large dots and at high temperatures.

46 CFR 160.054-2 - Type and size.

Code of Federal Regulations, 2011 CFR

2011-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Kits, First-Aid, for Inflatable Liferafts § 160.054-2 Type and size. (a) Type. First-aid kits covered by this specification shall be of the water-tight type... special consideration. (b) Size. First-aid kits shall be of a size adequate for packing 12 standard single...

46 CFR 160.054-2 - Type and size.

Code of Federal Regulations, 2014 CFR

2014-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Kits, First-Aid, for Inflatable Liferafts § 160.054-2 Type and size. (a) Type. First-aid kits covered by this specification shall be of the water-tight type... special consideration. (b) Size. First-aid kits shall be of a size adequate for packing 12 standard single...

46 CFR 160.054-2 - Type and size.

Code of Federal Regulations, 2013 CFR

2013-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Kits, First-Aid, for Inflatable Liferafts § 160.054-2 Type and size. (a) Type. First-aid kits covered by this specification shall be of the water-tight type... special consideration. (b) Size. First-aid kits shall be of a size adequate for packing 12 standard single...

46 CFR 160.054-2 - Type and size.

Code of Federal Regulations, 2012 CFR

2012-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Kits, First-Aid, for Inflatable Liferafts § 160.054-2 Type and size. (a) Type. First-aid kits covered by this specification shall be of the water-tight type... special consideration. (b) Size. First-aid kits shall be of a size adequate for packing 12 standard single...

46 CFR 160.054-2 - Type and size.

Code of Federal Regulations, 2010 CFR

2010-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Kits, First-Aid, for Inflatable Liferafts § 160.054-2 Type and size. (a) Type. First-aid kits covered by this specification shall be of the water-tight type... special consideration. (b) Size. First-aid kits shall be of a size adequate for packing 12 standard single...

The incidence and location of prostatic calculi on noncontrast computed tomography images in patients with renal calculi.

PubMed

Balasar, Mehmet; Poyraz, Necdet; Göğer, Yunus Emre; Unal, Yunus; Pişkin, Mehmet Mesut

2015-08-01

In this study, the incidence and location of prostatic calculi on noncontrast abdominal computed tomography (NCACT) images of patients with and without renal stones were investigated. Between 2006 and 2013, NCACT images were taken of 133 patients treated for renal stones (Group I) and of 100 age-matched control patients with putative urinary stone disease (Group II) in our clinic. The incidence and location of prostatic calculi on these images were determined. The location of prostatic calculus was classified as type A if they were located in the main prostatic ducts, and type B if they were located outside the ducts. Prostatic calculi were present in 44.4% of patients in Group I and 21.0% of patients in Group II. The incidence of prostatic calculi was significantly higher in patients with urinary stones compared with those without (P<0.001). The location of prostatic calculi in Group I included 74.6% type A and 25.4% type B while in Group II the locations were 76.2% type A and 23.8% type B. The incidence of prostatic calculi is more prevalent in patients with renal stones. On NCACT images, prostatic calculi were mostly detected in the main prostatic ducts, which were defined as type A.

Modeling loggerhead turtle movement in the Mediterranean: importance of body size and oceanography.

PubMed

Eckert, Scott A; Moore, Jeffrey E; Dunn, Daniel C; van Buiten, Ricardo Sagarminaga; Eckert, Karen L; Halpin, Patrick N

2008-03-01

Adapting state-space models (SSMs) to telemetry data has been helpful for dealing with location error and for modeling animal movements. We used a combination of two hierarchical Bayesian SSMs to estimate movement pathways from Argos satellite-tag data for 15 juvenile loggerhead turtles (Caretta caretta) in the western Mediterranean Sea, and to probabilistically assign locations to one of two behavioral movement types and relate those behaviors to environmental features. A Monte Carlo procedure helped propagate location uncertainty from the first SSM into the estimation of behavioral states and environment--behavior relationships in the second SSM. Turtles using oceanic habitats of the Balearic Sea (n = 9 turtles) within the western Mediterranean were more likely to exhibit "intensive search" behavior as might occur during foraging, but only larger turtles responded to variations in sea-surface height. This suggests that they were better able than smaller turtles to cue on environmental features that concentrate prey resources or were more dependent on high-quality feeding areas. These findings stress the importance of individual heterogeneity in the analysis of movement behavior and, taken in concert with descriptive studies of Pacific loggerheads, suggest that directed movements toward patchy ephemeral resources may be a general property of larger juvenile loggerheads in different populations. We discovered size-based variation in loggerhead distribution and documented use of the western Mediterranean Sea by turtles larger than previously thought to occur there. With one exception, only individuals > 57 cm curved carapace length used the most westerly basin in the Mediterranean (western Alborán Sea). These observations shed new light on loggerhead migration phenology.

ZOOPLANKTON SIZE-SPECTRA IN GREAT LAKES COASTAL WATERS

EPA Science Inventory

Zooplankton mean size and size-distribution are affected by planktivore pressure and potentially reflect the condition of trophic interactions and ecosystem health. We used an optical plankton counter (OPC) to survey and assess zooplankton size-spectra for twenty locations in Lak...

Associations between joint attention and language in autism spectrum disorder and typical development: A systematic review and meta-regression analysis.

PubMed

Bottema-Beutel, Kristen

2016-10-01

Using a structured literature search and meta-regression procedures, this study sought to determine whether associations between joint attention and language are moderated by group (autism spectrum disorder [ASD] vs. typical development [TD]), joint attention type (responding to joint attention [RJA] vs. other), and other study design features and participant characteristics. Studies were located using database searches, hand searches, and electronic requests for data from experts in the field. This resulted in 71 reports or datasets and 605 effect sizes, representing 1,859 participants with ASD and 1,835 TD participants. Meta-regression was used to answer research questions regarding potential moderators of the effect sizes of interest, which were Pearson's r values quantifying the association between joint attention and language variables. In the final models, conducted separately for each language variable, effect sizes were significantly higher for the ASD group as compared to the TD group, and for RJA as compared to non-RJA joint attention types. Approximate mental age trended toward significance for the expressive language model. Joint attention may be more tightly tied to language in children with ASD as compared to TD children because TD children exhibit joint attention at sufficient thresholds so that language development becomes untethered to variations in joint attention. Conversely, children with ASD who exhibit deficits in joint attention develop language contingent upon their joint attention abilities. Because RJA was more strongly related to language than other types of joint attention, future research should involve careful consideration of the operationalization and measurement of joint attention constructs. Autism Res 2016, 9: 1021-1035. © 2016 International Society for Autism Research, Wiley Periodicals, Inc. © 2016 International Society for Autism Research, Wiley Periodicals, Inc.

The role of drop velocity in statistical spray description

NASA Technical Reports Server (NTRS)

Groeneweg, J. F.; El-Wakil, M. M.; Myers, P. S.; Uyehara, O. A.

1978-01-01

The justification for describing a spray by treating drop velocity as a random variable on an equal statistical basis with drop size was studied experimentally. A double exposure technique using fluorescent drop photography was used to make size and velocity measurements at selected locations in a steady ethanol spray formed by a swirl atomizer. The size velocity data were categorized to construct bivariate spray density functions to describe the spray immediately after formation and during downstream propagation. Bimodal density functions were formed by environmental interaction during downstream propagation. Large differences were also found between spatial mass density and mass flux size distribution at the same location.

Some properties of three αB-crystallin mutants carrying point substitutions in the C-terminal domain and associated with congenital diseases.

PubMed

Gerasimovich, Evgeniia S; Strelkov, Sergei V; Gusev, Nikolai B

2017-11-01

Physico-chemical properties of G154S, R157H and A171T mutants of αB-crystallin (HspB5) associated with congenital human diseases including certain myopathies and cataract were investigated. Oligomers formed by G154S and A171T mutants have the size and apparent molecular weight indistinguishable from those of the wild-type HspB5, whereas the size of oligomers formed by R157H mutant is slightly smaller. All mutants are less thermostable and start to aggregate at a lower temperature than the wild-type protein. All mutants effectively interact with a triple phosphomimicking mutant of HspB1 and form large heterooligomeric complexes of similar composition. All mutants interact with HspB6 forming heterooligomeric complexes with size and composition dependent on the molar ratio of two proteins. The wild-type HspB5 and its G154S and A171T mutants form only high molecular weight (300-450 kDa) heterooligomeric complexes with HspB6, whereas the R157H mutant forms both high and low (∼120 kDa) molecular weight complexes. The wild-type HspB5 and its G154S and A171T mutants form two types of heterooligomers with HspB4, whereas R157H mutant effectively forms only one type of heterooligomers with HspB4. G154S and A171T mutants have lower chaperone-like activity than the wild-type protein when subfragment S1 of myosin or β L -crystallin are used as a model substrates. With these substrates, the R157H mutant shows equal or higher chaperone activity than the wild-type HspB5. We hypothesize that the mutations in the C-terminal region modulate the binding of the IP(I/V) motif to the core α-crystallin domain. The R157H mutation is located in the immediate proximity of this motif. Such modulation could cause altered interaction of HspB5 with partners and substrates and eventually lead to pathological processes. Copyright © 2017 Elsevier B.V. and Société Française de Biochimie et Biologie Moléculaire (SFBBM). All rights reserved.

The Impact of Fish Predation and Cyanobacteria on Zooplankton Size Structure in 96 Subtropical Lakes

PubMed Central

Zhang, Jing; Xie, Ping; Tao, Min; Guo, Longgen; Chen, Jun; Li, Li; XueZhen Zhang; Zhang, Lu

2013-01-01

Zooplankton are relatively small in size in the subtropical regions. This characteristic has been attributed to intense predation pressure, high nutrient loading and cyanobacterial biomass. To provide further information on the effect of predation and cyanobacteria on zooplankton size structure, we analyzed data from 96 shallow aquaculture lakes along the Yangtze River. Contrary to former studies, both principal components analysis and multiple regression analysis showed that the mean zooplankton size was positively related to fish yield. The studied lakes were grouped into three types, namely, natural fishing lakes with low nutrient loading (Type1), planktivorous fish-dominated lakes (Type 2), and eutrophic lakes with high cyanobacterial biomass (Type 3). A marked difference in zooplankton size structure was found among these groups. The greatest mean zooplankton size was observed in Type 2 lakes, but zooplankton density was the lowest. Zooplankton abundance was highest in Type 3 lakes and increased with increasing cyanobacterial biomass. Zooplankton mean size was negatively correlated with cyanobacterial biomass. No obvious trends were found in Type 1 lakes. These results were reflected by the normalized biomass size spectrum, which showed a unimodal shape with a peak at medium sizes in Type 2 lakes and a peak at small sizes in Type 3 lakes. These results indicated a relative increase in medium-sized and small-sized species in Types 2 and 3 lakes, respectively. Our results suggested that fish predation might have a negative effect on zooplankton abundance but a positive effect on zooplankton size structure. High cyanobacterial biomass most likely caused a decline in the zooplankton size and encouraged the proliferation of small zooplankton. We suggest that both planktivorous fish and cyanobacteria have substantial effects on the shaping of zooplankton community, particularly in the lakes in the eastern plain along the Yangtze River where aquaculture is widespread and nutrient loading is high. PMID:24124552

The impact of fish predation and cyanobacteria on zooplankton size structure in 96 subtropical lakes.

PubMed

Zhang, Jing; Xie, Ping; Tao, Min; Guo, Longgen; Chen, Jun; Li, Li; Xuezhen Zhang; Zhang, Lu

2013-01-01

Zooplankton are relatively small in size in the subtropical regions. This characteristic has been attributed to intense predation pressure, high nutrient loading and cyanobacterial biomass. To provide further information on the effect of predation and cyanobacteria on zooplankton size structure, we analyzed data from 96 shallow aquaculture lakes along the Yangtze River. Contrary to former studies, both principal components analysis and multiple regression analysis showed that the mean zooplankton size was positively related to fish yield. The studied lakes were grouped into three types, namely, natural fishing lakes with low nutrient loading (Type1), planktivorous fish-dominated lakes (Type 2), and eutrophic lakes with high cyanobacterial biomass (Type 3). A marked difference in zooplankton size structure was found among these groups. The greatest mean zooplankton size was observed in Type 2 lakes, but zooplankton density was the lowest. Zooplankton abundance was highest in Type 3 lakes and increased with increasing cyanobacterial biomass. Zooplankton mean size was negatively correlated with cyanobacterial biomass. No obvious trends were found in Type 1 lakes. These results were reflected by the normalized biomass size spectrum, which showed a unimodal shape with a peak at medium sizes in Type 2 lakes and a peak at small sizes in Type 3 lakes. These results indicated a relative increase in medium-sized and small-sized species in Types 2 and 3 lakes, respectively. Our results suggested that fish predation might have a negative effect on zooplankton abundance but a positive effect on zooplankton size structure. High cyanobacterial biomass most likely caused a decline in the zooplankton size and encouraged the proliferation of small zooplankton. We suggest that both planktivorous fish and cyanobacteria have substantial effects on the shaping of zooplankton community, particularly in the lakes in the eastern plain along the Yangtze River where aquaculture is widespread and nutrient loading is high.

Microstructures in naturally deformed Upper Rotliegend salt rocks from Northern Germany

NASA Astrophysics Data System (ADS)

Henneberg, Mareike; Hammer, Jörg; Mertineit, Michael

2017-04-01

Permian and Meso-/Cenozoic salt formations are represented in wide parts of the German geologic underground (Reinhold & Hammer 2016). They are of interest for cavern storage of oil and gas as well as of renewable energies (in form of compressed air or hydrogen). For industrial exploration purposes, more detailed data about the composition, barrier properties, as well as the genesis and deformation of the rocks is needed. In central Northern Germany, salt rocks from the Upper Rotliegend are implemented in diapir structures together with salt formations from the Zechstein. Rotliegend salt rocks are characterized by halite that contains patches of detrital material which account for 5 to 60 vol.% of the rock. They show a characteristic red to purple color. Drill cores containing Rotliegend halite rocks from different locations were investigated in this study by using petrographical and microstructural methods. The halite shows different fabric types: (i) euhedral to hypidiomorphic grains with grain sizes up to several millimeters, (ii) polygonal grains with smaller grain sizes between 0.1 and 3 mm, and (iii) fibrous halite. Halite grain boundaries are decorated with fluid inclusions, especially around the contact to detrital material. Subgrains in halite are abundant in all investigated samples and show average sizes between 140 µm and 217 µm. These correspond to average differential stresses of 1 MPa to 1.45 MPa (Carter et al. 1993, Schléder & Urai 2005). The detrital material consists of clasts of quartz, feldspar, mica, carbonates and metal oxides with grain sizes of clay to silt fraction. In some samples, the detrital components show internal deformation by folding and fracturing. Depending on the location, different quantities of authigenic evaporite minerals, like carbonate and anhydrite, formed. Fractures are filled with halite, anhydrite and celestine. The different types of halite fabric are an indication of locally different deformational behavior of the rocks, which depends mainly on the amount and type of detrital material. The observed subgrain formation points to intracrystalline dislocation creep as a deformation mechanism, which has occurred in different types of halite fabric. However, the high amount of fluid inclusions around material boundaries also point to an interaction of the different material components, which locally might have enhanced fluid based grain boundary migration during deformation. It is still to be investigated, how the overall rheological behavior of Rotliegend halite is influenced by the detrital components. Carter, N.L., Horseman, S.T., Russel, J.E. & Handin, J. 1993. Rheology of rocksalt. J. Struct. Geol., 15 (9-10), 1257-1271. Reinhold, K. & Hammer, J. 2016. Steinsalzlager in den salinaren Formationen Deutschlands. Z. Dt. Ges. Geowiss. 167, 167-190. Schléder, Z. & Urai, J.L. 2005. Microstructual evolution of deformation-modified primary halite from the Middle Triassic Röt Formation at Hengelo. The Netherlands, Int. J. Earth Sci. 94, 941-955.

SU-E-T-604: Penumbra Characteristics of a New InCiseâ„¢ Multileaf Collimator of CyberKnife M6â„¢ System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, M; Jang, S; Ozhasoglu, C

2015-06-15

Purpose: The InCise™ Multileaf Collimator (MLC) of CyberKnife M6™ System has been released recently. The purpose of this study was to explore the dosimetric characteristics of the new MLC. In particular, the penumbra characteristics of MLC fields at varying locations are evaluated. Methods: EBT3-based film measurements were performed with varying MLC fields ranging from 7.5 mm to 27.5 mm. Seventeen regions of interests (ROIs) were identified for irradiation. These are regions located at the central area (denoted as reference field), at the left/right edge areas of reference open field, at an intermediate location between central and edge area. Single beammore » treatment plans were designed by using the MultiPlan and was delivered using the Blue Phantom. Gafchromic films were irradiated at 1.5 cm depth in the Blue Phantom and analyzed using the Film Pro software. Variation of maximum dose, penumbra of MLC-defined fields, and symmetry/flatness were calculated as a function of locations of MLC fields. Results: The InCise™ MLC System showed relatively consistent dose distribution and penumbra size with varying locations of MLC fields. The measured maximum dose varied within 5 % at different locations compared to that at the central location and agreed with the calculated data well within 2%. The measured penumbrae were in the range of 2.9 mm and 3.7 mm and were relatively consistent regardless of locations. However, dose profiles in the out-of-field and in-field regions varied with locations and field sizes. Strong variation was seen for all fields located at 55 mm away from the central field. The MLC leakage map showed that the leakage is dependent on position. Conclusion: The size of penumbra and normalized maximum dose for MLC-defined fields were consistent in different regions of MLC. However, dose profiles in the out-field region varied with locations and field sizes.« less

Mineralogy and characterization of deposited particles of the aero sediments collected in the vicinity of power plants and the open pit coal mine: Kolubara (Serbia).

PubMed

Cvetković, Željko; Logar, Mihovil; Rosić, Aleksandra

2013-05-01

In this paper, particular attention was paid to the presence of aerosol solid particles, which occurred mainly as a result of exploitation and coal combustion in the thermal power plants of the Kolubara basin. Not all of the particles created by this type of anthropogenic pollution have an equal impact on human health, but it largely depends on their size and shape. The mineralogical composition and particle size distribution in the samples of aero sediments were defined. The samples were collected close to the power plant and open pit coal mine, in the winter and summer period during the year 2007. The sampling was performed by using precipitators placed in eight locations within the territory of the Lazarevac municipality. In order to characterize the sedimentary particles, several methods were applied: microscopy, SEM-EDX and X-ray powder diffraction. The concentration of aero sediments was also determined during the test period. Variety in the mineralogical composition and particle size depends on the position of the measuring sites, geology of the locations, the annual period of collecting as well as possible interactions. By applying the mentioned methods, the presence of inhalational and respiratory particles variously distributed in the winter and in the summer period was established. The most common minerals are quartz and feldspar. The presence of gypsum, clay minerals, calcite and dolomite as secondary minerals was determined, as well as the participation of organic and inorganic amorphic matter. The presence of quartz as a toxic mineral has a particular impact on human health.

Observations of coarse sediment movements on the mixed beach of the Elwha Delta, Washington

USGS Publications Warehouse

Miller, I.M.; Warrick, J.A.; Morgan, C.

2011-01-01

Mixed beaches, with poorly sorted grains of multiple sizes, are a common and globally distributed shoreline type. Despite this, rates and mechanisms of sediment transport on mixed beaches are poorly understood. A series of tracer deployments using native clasts implanted with Radio Frequency Identifier (RFID) tags was used to develop a better understanding of sediment transport directions and magnitudes on the mixed grain-size beach of the Elwha River delta. Using tracer samples selected to match the distribution of the coarse fraction on the beach we find that all grain sizes, up to large cobbles (128-256 mm), were mobile under most measured wave conditions and move in relationship to the direction of the alongshore component of wave energy as estimated by incident breaking wave angles. In locations where the breaking wave is normal to the shoreline we find that tracers move in both alongshore directions with approximately equal frequency. In locations where breaking waves are oblique to the shoreline we find that alongshore transport is more unidirectional and tracers can approach average velocities of 100. m/day under winter wave conditions. We use the tracer cloud to estimate the beach active width, the mobile layer depth and sediment velocity. Our results suggest that, while sediment velocity increases under increased incident wave angles, the active layer depth and width decrease, reducing sediment flux at the site with the more oblique breaking waves. This result is contrary to what is suggested by traditional wave energy transport models of alongshore sediment transport. ?? 2011 Elsevier B.V.

Spectroscopic monitoring of bright A-F type candidate hybrid stars discovered by the Kepler mission

NASA Astrophysics Data System (ADS)

Lampens, Patricia; Frémat, Y.; Vermeylen, Lore; De Cat, Peter; Dumortier, Louis; Sódor, Ádám; Sharka, Marek; Bognár, Zsófia

2018-04-01

We report on a study of 250 optical spectra for 50 bright A/F-type candidate hybrid pulsating stars from the Kepler field. Most of the spectra have been collected with the high-resolution spectrograph HERMES attached to the Mercator telescope, La Palma. We determined the radial velocities (RVs), projected rotational velocities, fundamental atmospheric parameters and provide a classification based on the appearance of the cross-correlation profiles and the behaviour of the RVs with time in order to find true hybrid pulsators. Additionally, we also detected new spectroscopic binary and multiple systems in our sample and determined the fraction of spectroscopic systems. In order to be able to extend this investigation to the fainter A-F type candidate hybrid stars, various high-quality spectra collected with 3-4 m sized telescopes suitably equipped with a high-resolution spectrograph and furthermore located in the Northern hemisphere would be ideal. This programme could be done using the new instruments installed at the Devasthal Observatory.

Developing Livestock Facility Type Information from USDA Agricultural Census Data for Use in Epidemiological and Economic Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melius, C; Robertson, A; Hullinger, P

2006-10-24

The epidemiological and economic modeling of livestock diseases requires knowing the size, location, and operational type of each livestock facility within the US. At the present time, the only national database of livestock facilities that is available to the general public is the USDA's 2002 Agricultural Census data, published by the National Agricultural Statistics Service, herein referred to as the 'NASS data.' The NASS data provides facility data at the county level for various livestock types (i.e., beef cows, milk cows, cattle on feed, other cattle, total hogs and pigs, sheep and lambs, milk goats, and angora goats). However, themore » number and sizes of facilities for the various livestock types are not independent since some facilities have more than one type of livestock, and some livestock are of more than one type (e.g., 'other cattle' that are being fed for slaughter are also 'cattle on feed'). In addition, any data tabulated by NASS that could identify numbers of animals or other data reported by an individual respondent is suppressed by NASS and coded with a 'D.'. To be useful for epidemiological and economic modeling, the NASS data must be converted into a unique set of facility types (farms having similar operational characteristics). The unique set must not double count facilities or animals. At the same time, it must account for all the animals, including those for which the data has been suppressed. Therefore, several data processing steps are required to work back from the published NASS data to obtain a consistent database for individual livestock operations. This technical report documents data processing steps that were used to convert the NASS data into a national livestock facility database with twenty-eight facility types. The process involves two major steps. The first step defines the rules used to estimate the data that is suppressed within the NASS database. The second step converts the NASS livestock types into the operational facility types used by the epidemiological and economic model. Comparison of the resulting database with an independent survey of farms in central California shows excellent agreement between the numbers of farms for the various facility types. This suggests that the NASS data are well suited for providing a consistent set of county-level information on facility numbers and sizes that can be used in epidemiological and economic models.« less

49 CFR 195.266 - Construction records.

Code of Federal Regulations, 2010 CFR

2010-10-01

... rejected weld. (b) The amount, location; and cover of each size of pipe installed. (c) The location of each... overhead crossing. (f) The location of each valve and corrosion test station. [Amdt. 195-22, 46 FR 38360...

Estimation of anomaly location and size using electrical impedance tomography.

PubMed

Kwon, Ohin; Yoon, Jeong Rock; Seo, Jin Keun; Woo, Eung Je; Cho, Young Gu

2003-01-01

We developed a new algorithm that estimates locations and sizes of anomalies in electrically conducting medium based on electrical impedance tomography (EIT) technique. When only the boundary current and voltage measurements are available, it is not practically feasible to reconstruct accurate high-resolution cross-sectional conductivity or resistivity images of a subject. In this paper, we focus our attention on the estimation of locations and sizes of anomalies with different conductivity values compared with the background tissues. We showed the performance of the algorithm from experimental results using a 32-channel EIT system and saline phantom. With about 1.73% measurement error in boundary current-voltage data, we found that the minimal size (area) of the detectable anomaly is about 0.72% of the size (area) of the phantom. Potential applications include the monitoring of impedance related physiological events and bubble detection in two-phase flow. Since this new algorithm requires neither any forward solver nor time-consuming minimization process, it is fast enough for various real-time applications in medicine and nondestructive testing.

Changes in myonuclear domain size do not precede muscle hypertrophy during prolonged resistance-type exercise training.

PubMed

Snijders, T; Smeets, J S J; van Kranenburg, J; Kies, A K; van Loon, L J C; Verdijk, L B

2016-02-01

Muscle fibre hypertrophy is accompanied by an increase in myonuclear number, an increase in myonuclear domain size or both. It has been suggested that increases in myonuclear domain size precede myonuclear accretion and subsequent muscle fibre hypertrophy during prolonged exercise training. In this study, we assessed the changes in muscle fibre size, myonuclear and satellite cell content throughout 12 weeks of resistance-type exercise training in young men. Twenty-two young men (23 ± 1 year) were assigned to a progressive, 12-weeks resistance-type exercise training programme (3 sessions per week). Muscle biopsies from the vastus lateralis muscle were taken before and after 2, 4, 8 and 12 weeks of exercise training. Muscle fibre size, myonuclear content, myonuclear domain size and satellite cell content were assessed by immunohistochemistry. Type I and type II muscle fibre size increased gradually throughout the 12 weeks of training (type I: 18 ± 5%, type II: 41 ± 6%, P < 0.01). Myonuclear content increased significantly over time in both the type I (P < 0.01) and type II (P < 0.001) muscle fibres. No changes in type I and type II myonuclear domain size were observed at any time point throughout the intervention. Satellite cell content increased significantly over time in both type I and type II muscle fibres (P < 0.001). Increases in myonuclear domain size do not appear to drive myonuclear accretion and muscle fibre hypertrophy during prolonged resistance-type exercise training in vivo in humans. © 2015 Scandinavian Physiological Society. Published by John Wiley & Sons Ltd.

Myonuclear domain size and myosin isoform expression in muscle fibres from mammals representing a 100,000-fold difference in body size.

PubMed

Liu, Jing-Xia; Höglund, Anna-Stina; Karlsson, Patrick; Lindblad, Joakim; Qaisar, Rizwan; Aare, Sudhakar; Bengtsson, Ewert; Larsson, Lars

2009-01-01

This comparative study of myonuclear domain (MND) size in mammalian species representing a 100,000-fold difference in body mass, ranging from 25 g to 2500 kg, was undertaken to improve our understanding of myonuclear organization in skeletal muscle fibres. Myonuclear domain size was calculated from three-dimensional reconstructions in a total of 235 single muscle fibre segments at a fixed sarcomere length. Irrespective of species, the largest MND size was observed in muscle fibres expressing fast myosin heavy chain (MyHC) isoforms, but in the two smallest mammalian species studied (mouse and rat), MND size was not larger in the fast-twitch fibres expressing the IIA MyHC isofom than in the slow-twitch type I fibres. In the larger mammals, the type I fibres always had the smallest average MND size, but contrary to mouse and rat muscles, type IIA fibres had lower mitochondrial enzyme activities than type I fibres. Myonuclear domain size was highly dependent on body mass in the two muscle fibre types expressed in all species, i.e. types I and IIA. Myonuclear domain size increased in muscle fibres expressing both the beta/slow (type I; r = 0.84, P < 0.001) and the fast IIA MyHC isoform (r = 0.90; P < 0.001). Thus, MND size scales with body size and is highly dependent on muscle fibre type, independent of species. However, myosin isoform expression is not the sole protein determining MND size, and other protein systems, such as mitochondrial proteins, may be equally or more important determinants of MND size.

Birth order in small multihospital systems.

PubMed

Luke, R D; Ozcan, Y A; Begun, J W

1990-06-01

The strategic behaviors of small multihospital systems have received little attention in the literature despite the fact that small systems are the predominant scale among multihospital systems. This study examines one important aspect of small-system strategic behaviors: the birth-order or evolutionary patterns of hospital acquisition. The evolutionary patterns of acquisition are compared across three strategic model types studied elsewhere: local market, investment, and historical. Using data obtained from a variety of sources, local market model systems are found, in the sequence of acquisition, to be significantly different from the other two model types in terms of relative distances of acquisitions from the initiating or parent hospital, the sizes of acquisition hospitals, the complexity of those hospitals, and the likelihood that the acquisitions are located in rural areas. Differences between parents and acquisitions are also significant, as hypothesized, for the market model system types, although they are not generally significant for the other two model types. The findings suggest that the market model represents an important strategic form that may have important implications for the restructuring of hospital markets.

Being selective at the plate: processing dependence between perceptual variables relates to hitting goals and performance.

PubMed

Gray, Rob

2013-08-01

Performance of a skill that involves acting on a goal object (e.g., a ball to be hit) can influence one's judgment of the size and speed of that object. The present study examined how these action-specific effects are affected when the goal of the actor is varied and they are free to choose between alternative actions. In Experiment 1, expert baseball players were asked to perform three different directional hitting tasks in a batting simulation and make interleaved perceptual judgments about three ball parameters (speed, plate crossing location, and size). Perceived ball size was largest (and perceived speed was slowest) when the ball crossing location was optimal for the particular hitting task the batter was performing (e.g., an "outside" pitch for opposite-field hitting). The magnitude of processing dependency between variables (speed vs. location and size vs. location) was positively correlated with batting performance. In Experiment 2, the action-specific effects observed in Experiment 1 were mimicked by systematically changing the ball diameter in the simulation as a function of plate crossing location. The number of swing initiations was greater when ball size was larger, and batters were more successful in the hitting task for which the larger pitches were optimal (e.g., greater number of pull hits than opposite-field hits when "inside" pitches were larger). These findings suggest attentional accentuation of goal-relevant targets underlies action-related changes in perception and are consistent with an action selection role for these effects. 2013 APA, all rights reserved

Myocardial infarction size and location: a comparative study of epicardial isopotential mapping, thallium-201 scintigraphy, electrocardiography and vectorcardiography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toyama, S.; Suzuki, K.; Takahashi, T.

1987-07-01

Based on epicardial isopotential mapping (the Ep Map), which was calculated from body surface isopotential mapping (the Body Map) with Yamashita's method, using the finite element technique, we predicted the location and size of the abnormal depolarized area (the infarcted area) in 19 clinical cases of anterior and 18 cases of inferoposterior infarction. The prediction was done using Toyama's diagnostic method, previously reported. The accuracy of the prediction by the Ep Map was assessed by comparing it with findings from thallium-201 scintigraphy (SCG), electrocardiography (ECG) and vectorcardiography (VCG). In all cases of anterior infarction, the location of the abnormal depolarizedmore » areas determined on the Ep Map, which was localized at the anterior wall along the anterior intraventricular septum, agreed with the location of the abnormal findings obtained by SCG, ECG and VCG. For all inferoposterior infarction cases, the abnormal depolarized areas were localized at the posterior wall and the location also coincided with that of the abnormal findings obtained by SCG, ECG and VCG. Furthermore, we ranked and ordered the size of the abnormal depolarized areas, which were predicted by the Ep Map for both anterior and inferoposterior infarction cases. In the cases of anterior infarction, the order of the size of the abnormal depolarized area by the Ep Map was correlated to the size of the abnormal findings by SCG, as well as to the results from Selvester's QRS scoring system in ECG and to the angle of the maximum QRS vector in the horizontal plane in VCG.« less

Anatomy and classification of the posterior tibial fragment in ankle fractures.

PubMed

Bartoníček, Jan; Rammelt, Stefan; Kostlivý, Karel; Vaněček, Václav; Klika, Daniel; Trešl, Ivo

2015-04-01

The aim of this study was to analyze the pathoanatomy of the posterior fragment on the basis of a comprehensive CT examination, including 3D reconstructions, in a large patient cohort. One hundred and forty one consecutive individuals with an ankle fracture or fracture-dislocation of types Weber B or Weber C and evidence of a posterior tibial fragment in standard radiographs were included in the study. The mean patient age was 49 years (range 19-83 years). The exclusion criteria were patients below 18 years of age, inability to provide written consent, fractures of the tibial pilon, posttraumatic arthritis and pre-existing deformities. In all patients, post-injury radiographs were obtained in anteroposterior, mortise and lateral views. All patients underwent CT scanning in transverse, sagittal and frontal planes. 3D CT reconstruction was performed in 91 patients. We were able to classify 137 cases into one of the following four types with constant pathoanatomic features: type 1: extraincisural fragment with an intact fibular notch, type 2: posterolateral fragment extending into the fibular notch, type 3: posteromedial two-part fragment involving the medial malleolus, type 4: large posterolateral triangular fragment. In the 4 cases it was not possible to classify the type of the posterior tibial fragment. These were collectively termed type 5 (irregular, osteoporotic fragments). It is impossible to assess the shape and size of the posterior malleolar fragment, involvement of the fibular notch, or the medial malleolus, on the basis of plain radiographs. The system that we propose for classification of fractures of the posterior malleolus is based on CT examination and takes into account the size, shape and location of the fragment, stability of the tibio-talar joint and the integrity of the fibular notch. It may be a useful indication for surgery and defining the most useful approach to these injuries.

Evolution of A-Type Macrosegregation in Large Size Steel Ingot After Multistep Forging and Heat Treatment

NASA Astrophysics Data System (ADS)

Loucif, Abdelhalim; Ben Fredj, Emna; Harris, Nathan; Shahriari, Davood; Jahazi, Mohammad; Lapierre-Boire, Louis-Philippe

2018-03-01

A-type macrosegregation refers to the channel chemical heterogeneities that can be formed during solidification in large size steel ingots. In this research, a combination of experiment and simulation was used to study the influence of open die forging parameters on the evolution of A-type macrosegregation patterns during a multistep forging of a 40 metric ton (MT) cast, high-strength steel ingot. Macrosegregation patterns were determined experimentally by macroetch along the longitudinal axis of the forged and heat-treated ingot. Mass spectroscopy, on more than 900 samples, was used to determine the chemical composition map of the entire longitudinal sectioned surface. FORGE NxT 1.1 finite element modeling code was used to predict the effect of forging sequences on the morphology evolution of A-type macrosegregation patterns. For this purpose, grain flow variables were defined and implemented in a large scale finite element modeling code to describe oriented grains and A-type segregation patterns. Examination of the A-type macrosegregation showed four to five parallel continuous channels located nearly symmetrical to the axis of the forged ingot. In some regions, the A-type patterns became curved or obtained a wavy form in contrast to their straight shape in the as-cast state. Mass spectrometry analysis of the main alloying elements (C, Mn, Ni, Cr, Mo, Cu, P, and S) revealed that carbon, manganese, and chromium were the most segregated alloying elements in A-type macrosegregation patterns. The observed differences were analyzed using thermodynamic calculations, which indicated that changes in the chemical composition of the liquid metal can affect the primary solidification mode and the segregation intensity of the alloying elements. Finite element modeling simulation results showed very good agreement with the experimental observations, thereby allowing for the quantification of the influence of temperature and deformation on the evolution of the shape of the macrosegregation channels during the open die forging process.

Evolution of A-Type Macrosegregation in Large Size Steel Ingot After Multistep Forging and Heat Treatment

NASA Astrophysics Data System (ADS)

Loucif, Abdelhalim; Ben Fredj, Emna; Harris, Nathan; Shahriari, Davood; Jahazi, Mohammad; Lapierre-Boire, Louis-Philippe

2018-06-01

A-type macrosegregation refers to the channel chemical heterogeneities that can be formed during solidification in large size steel ingots. In this research, a combination of experiment and simulation was used to study the influence of open die forging parameters on the evolution of A-type macrosegregation patterns during a multistep forging of a 40 metric ton (MT) cast, high-strength steel ingot. Macrosegregation patterns were determined experimentally by macroetch along the longitudinal axis of the forged and heat-treated ingot. Mass spectroscopy, on more than 900 samples, was used to determine the chemical composition map of the entire longitudinal sectioned surface. FORGE NxT 1.1 finite element modeling code was used to predict the effect of forging sequences on the morphology evolution of A-type macrosegregation patterns. For this purpose, grain flow variables were defined and implemented in a large scale finite element modeling code to describe oriented grains and A-type segregation patterns. Examination of the A-type macrosegregation showed four to five parallel continuous channels located nearly symmetrical to the axis of the forged ingot. In some regions, the A-type patterns became curved or obtained a wavy form in contrast to their straight shape in the as-cast state. Mass spectrometry analysis of the main alloying elements (C, Mn, Ni, Cr, Mo, Cu, P, and S) revealed that carbon, manganese, and chromium were the most segregated alloying elements in A-type macrosegregation patterns. The observed differences were analyzed using thermodynamic calculations, which indicated that changes in the chemical composition of the liquid metal can affect the primary solidification mode and the segregation intensity of the alloying elements. Finite element modeling simulation results showed very good agreement with the experimental observations, thereby allowing for the quantification of the influence of temperature and deformation on the evolution of the shape of the macrosegregation channels during the open die forging process.

Correlation of magnetic perturbation inspection data with rolling element bearing fatigue results

NASA Technical Reports Server (NTRS)

Parker, R. J.

1973-01-01

A magnetic perturbation technique was used to nondestructively detect subsurface nonmetallic inclusions in the inner races of 207-size, deep groove ball bearings. The bearings were fatigue tested at 2750 rpm under a radial load of. The inner races were subsequently sectioned at fatigue spall locations and at magnetic perturbation signal locations. Analyses of the data indicated good correlation between magnetic perturbation signals and inclusion size and location. Exclusion of those bearings that had significant magnetic perturbation signals did not alter the statistical life of the bearings.

Elucidating the trophodynamics of four coral reef fishes of the Solomon Islands using δ15N and δ13C

NASA Astrophysics Data System (ADS)

Greenwood, N. D. W.; Sweeting, C. J.; Polunin, N. V. C.

2010-09-01

Size-related diet shifts are important characteristics of fish trophodynamics. Here, body size-related changes in muscle δ15N and δ13C of four coral reef fishes, Acanthurus nigrofuscus (herbivore), Chaetodon lunulatus (corallivore) , Chromis xanthura (planktivore) and Plectropomus leopardus (piscivore) were investigated at two locations in the Solomon Islands. All four species occupied distinct isotopic niches and the concurrent δ13C' values of C. xanthura and P. leopardus suggested a common planktonic production source. Size-related shifts in δ15N, and thus trophic level, were observed in C. xanthura, C. lunulatus and P. leopardus, and these trends varied between location, indicating spatial differences in trophic ecology. A literature review of tropical fishes revealed that positive δ15N-size trends are common while negative δ15N-size trends are rare. Size-δ15N trends fall into approximately equal groups representing size-based feeding within a food chain, and that associated with a basal resource shift and occurs in conjunction with changes in production source, indicated by δ13C. The review also revealed large scale differences in isotope-size trends and this, combined with small scale location differences noted earlier, highlights a high degree of plasticity in the reef fishes studied. This suggests that trophic size analysis of reef fishes would provide a productive avenue to identify species potentially vulnerable to reef impacts as a result of constrained trophic behaviour.

Autonomous bed-sediment imaging-systems for revealing temporal variability of grain size

USGS Publications Warehouse

Buscombe, Daniel; Rubin, David M.; Lacy, Jessica R.; Storlazzi, Curt D.; Hatcher, Gerald; Chezar, Henry; Wyland, Robert; Sherwood, Christopher R.

2014-01-01

We describe a remotely operated video microscope system, designed to provide high-resolution images of seabed sediments. Two versions were developed, which differ in how they raise the camera from the seabed. The first used hydraulics and the second used the energy associated with wave orbital motion. Images were analyzed using automated frequency-domain methods, which following a rigorous partially supervised quality control procedure, yielded estimates to within 20% of the true size as determined by on-screen manual measurements of grains. Long-term grain-size variability at a sandy inner shelf site offshore of Santa Cruz, California, USA, was investigated using the hydraulic system. Eighteen months of high frequency (min to h), high-resolution (μm) images were collected, and grain size distributions compiled. The data constitutes the longest known high-frequency record of seabed-grain size at this sample frequency, at any location. Short-term grain-size variability of sand in an energetic surf zone at Praa Sands, Cornwall, UK was investigated using the ‘wave-powered’ system. The data are the first high-frequency record of grain size at a single location of a highly mobile and evolving bed in a natural surf zone. Using this technology, it is now possible to measure bed-sediment-grain size at a time-scale comparable with flow conditions. Results suggest models of sediment transport at sandy, wave-dominated, nearshore locations should allow for substantial changes in grain-size distribution over time-scales as short as a few hours.

Length scale hierarchy and spatiotemporal change of alluvial morphologies over the Selenga River delta, Russia

NASA Astrophysics Data System (ADS)

Dong, T. Y.; Nittrouer, J.; McElroy, B. J.; Ma, H.; Czapiga, M. J.; Il'icheva, E.; Pavlov, M.; Parker, G.

2017-12-01

The movement of water and sediment in natural channels creates various types of alluvial morphologies that span length scales from dunes to deltas. The behavior of these morphologies is controlled microscopically by hydrodynamic conditions and bed material size, and macroscopically by hydrologic and geological settings. Alluvial morphologies can be modeled as either diffusive or kinematic waves, in accordance with their respective boundary conditions. Recently, it has been shown that the difference between these two dynamic behaviors of alluvial morphologies can be characterized by the backwater number, which is a dimensionless value normalizing the length scale of a morphological feature to its local hydrodynamic condition. Application of the backwater number has proven useful for evaluating the size of morphologies, including deltas (e.g., by assessing the preferential avulsion location of a lobe), and for comparing bedform types across different fluvial systems. Yet two critical questions emerge when applying the backwater number: First, how do different types of alluvial morphologies compare within a single deltaic system, where there is a hydrodynamic transition from uniform to non-uniform flow? Second, how do different types of morphologies evolve temporally within a system as a function of changing water discharge? This study addresses these questions by compiling and analyzing field data from the Selenga River delta, Russia, which include measurements of flow velocity, channel geometry, bed material grain size, and channel slope, as well as length scales of various morphologies, including dunes, island bars, meanders, bifurcations, and delta lobes. Data analyses reveal that the length scale of morphologies decrease and the backwater number increases as flow transitions from uniform to non-uniform conditions progressing downstream. It is shown that the evaluated length scale hierarchy and planform distribution of different morphologies can be used to estimate slope, shear velocity and sediment flux within this depositional system. The findings from this research can be applied to evaluate spatially and temporally varying morphodynamic conditions, based on structures measured from both modern systems and ancient sedimentary records.

Developmental Differences in Preferences for Using Color, Size, and Location Information to Disambiguate Hiding Places

ERIC Educational Resources Information Center

Plumert, Jodie M.; Nichols-Whitehead, Penney

2007-01-01

We conducted four experiments to examine developmental differences in preferences for using color, size, and location information to disambiguate hiding places. Three- and 4-year-olds and adults described how to find a miniature mouse that was hidden in one of two highly similar small objects in a dollhouse. In Experiment 1, the hiding places…

The Visual System's Intrinsic Bias and Knowledge of Size Mediate Perceived Size and Location in the Dark

ERIC Educational Resources Information Center

Zhou, Liu; He, Zijiang J.; Ooi, Teng Leng

2013-01-01

Dimly lit targets in the dark are perceived as located about an implicit slanted surface that delineates the visual system's intrinsic bias (Ooi, Wu, & He, 2001). If the intrinsic bias reflects the internal model of visual space--as proposed here--its influence should extend beyond target localization. Our first 2 experiments demonstrated that…

Cytogenetic features of rRNA genes across land plants: analysis of the Plant rDNA database.

PubMed

Garcia, Sònia; Kovařík, Ales; Leitch, Andrew R; Garnatje, Teresa

2017-03-01

The online resource http://www.plantrdnadatabase.com/ stores information on the number, chromosomal locations and structure of the 5S and 18S-5.8S-26S (35S) ribosomal DNAs (rDNA) in plants. This resource was exploited to study relationships between rDNA locus number, distribution, the occurrence of linked (L-type) and separated (S-type) 5S and 35S rDNA units, chromosome number, genome size and ploidy level. The analyses presented summarise current knowledge on rDNA locus numbers and distribution in plants. We analysed 2949 karyotypes, from 1791 species and 86 plant families, and performed ancestral character state reconstructions. The ancestral karyotype (2n = 16) has two terminal 35S sites and two interstitial 5S sites, while the median (2n = 24) presents four terminal 35S sites and three interstitial 5S sites. Whilst 86.57% of karyotypes show S-type organisation (ancestral condition), the L-type arrangement has arisen independently several times during plant evolution. A non-terminal position of 35S rDNA was found in about 25% of single-locus karyotypes, suggesting that terminal locations are not essential for functionality and expression. Single-locus karyotypes are very common, even in polyploids. In this regard, polyploidy is followed by subsequent locus loss. This results in a decrease in locus number per monoploid genome, forming part of the diploidisation process returning polyploids to a diploid-like state over time. © 2016 The Authors The Plant Journal © 2016 John Wiley & Sons Ltd.

A generic bio-economic farm model for environmental and economic assessment of agricultural systems.

PubMed

Janssen, Sander; Louhichi, Kamel; Kanellopoulos, Argyris; Zander, Peter; Flichman, Guillermo; Hengsdijk, Huib; Meuter, Eelco; Andersen, Erling; Belhouchette, Hatem; Blanco, Maria; Borkowski, Nina; Heckelei, Thomas; Hecker, Martin; Li, Hongtao; Oude Lansink, Alfons; Stokstad, Grete; Thorne, Peter; van Keulen, Herman; van Ittersum, Martin K

2010-12-01

Bio-economic farm models are tools to evaluate ex-post or to assess ex-ante the impact of policy and technology change on agriculture, economics and environment. Recently, various BEFMs have been developed, often for one purpose or location, but hardly any of these models are re-used later for other purposes or locations. The Farm System Simulator (FSSIM) provides a generic framework enabling the application of BEFMs under various situations and for different purposes (generating supply response functions and detailed regional or farm type assessments). FSSIM is set up as a component-based framework with components representing farmer objectives, risk, calibration, policies, current activities, alternative activities and different types of activities (e.g., annual and perennial cropping and livestock). The generic nature of FSSIM is evaluated using five criteria by examining its applications. FSSIM has been applied for different climate zones and soil types (criterion 1) and to a range of different farm types (criterion 2) with different specializations, intensities and sizes. In most applications FSSIM has been used to assess the effects of policy changes and in two applications to assess the impact of technological innovations (criterion 3). In the various applications, different data sources, level of detail (e.g., criterion 4) and model configurations have been used. FSSIM has been linked to an economic and several biophysical models (criterion 5). The model is available for applications to other conditions and research issues, and it is open to be further tested and to be extended with new components, indicators or linkages to other models.

A Generic Bio-Economic Farm Model for Environmental and Economic Assessment of Agricultural Systems

PubMed Central

Louhichi, Kamel; Kanellopoulos, Argyris; Zander, Peter; Flichman, Guillermo; Hengsdijk, Huib; Meuter, Eelco; Andersen, Erling; Belhouchette, Hatem; Blanco, Maria; Borkowski, Nina; Heckelei, Thomas; Hecker, Martin; Li, Hongtao; Oude Lansink, Alfons; Stokstad, Grete; Thorne, Peter; van Keulen, Herman; van Ittersum, Martin K.

2010-01-01

Bio-economic farm models are tools to evaluate ex-post or to assess ex-ante the impact of policy and technology change on agriculture, economics and environment. Recently, various BEFMs have been developed, often for one purpose or location, but hardly any of these models are re-used later for other purposes or locations. The Farm System Simulator (FSSIM) provides a generic framework enabling the application of BEFMs under various situations and for different purposes (generating supply response functions and detailed regional or farm type assessments). FSSIM is set up as a component-based framework with components representing farmer objectives, risk, calibration, policies, current activities, alternative activities and different types of activities (e.g., annual and perennial cropping and livestock). The generic nature of FSSIM is evaluated using five criteria by examining its applications. FSSIM has been applied for different climate zones and soil types (criterion 1) and to a range of different farm types (criterion 2) with different specializations, intensities and sizes. In most applications FSSIM has been used to assess the effects of policy changes and in two applications to assess the impact of technological innovations (criterion 3). In the various applications, different data sources, level of detail (e.g., criterion 4) and model configurations have been used. FSSIM has been linked to an economic and several biophysical models (criterion 5). The model is available for applications to other conditions and research issues, and it is open to be further tested and to be extended with new components, indicators or linkages to other models. PMID:21113782

Quantifying home range habitat requirements for bobcats (Lynx rufus) in Vermont, USA

USGS Publications Warehouse

Donovan, Therese; Freeman, Mark; Abouelezz, Hanem; Royar, Kim; Howard, Alan D.; Mickey, R.

2011-01-01

We demonstrate how home range and habitat use analysis can inform landscape-scale conservation planning for the bobcat, Lynx rufus, in Vermont USA. From 2005 to 2008, we outfitted fourteen bobcats with GPS collars that collected spatially explicit locations from individuals every 4 h for 3–4 months. Kernel home range techniques were used to estimate home range size and boundaries, and to quantify the utilization distribution (UD), which is a spatially explicit, topographic mapping of how different areas within the home range are used. We then used GIS methods to quantify both biotic (e.g. habitat types, stream density) and abiotic (e.g. slope) resources within each bobcat’s home range. Across bobcats, upper 20th UD percentiles (core areas) had 18% less agriculture, 42% less development, 26% more bobcat habitat (shrub, deciduous, coniferous forest, and wetland cover types), and 33% lower road density than lower UD percentiles (UD valleys). For each bobcat, we used Akaike’s Information Criterion (AIC) to evaluate and compare 24 alternative Resource Utilization Functions (hypotheses) that could explain the topology of the individual’s UD. A model-averaged population-level Resource Utilization Function suggested positive responses to shrub, deciduous, coniferous forest, and wetland cover types within 1 km of a location, and negative responses to roads and mixed forest cover types within 1 km of a location. Applying this model-averaged function to each pixel in the study area revealed habitat suitability for bobcats across the entire study area, with suitability scores ranging between −1.69 and 1.44, where higher values were assumed to represent higher quality habitat. The southern Champlain Valley, which contained ample wetland and shrub habitat, was a concentrated area of highly suitable habitat, while areas at higher elevation areas were less suitable. Female bobcat home ranges, on average, had an average habitat suitability score of near 0, indicating that home ranges consisted of both beneficial and detrimental habitat types. We discuss the application of habitat suitability mapping and home range requirements for bobcat conservation and landscape scale management.

Quantifying home range habitat requirements for bobcats (Lynx rufus) in Vermont, USA

USGS Publications Warehouse

Donovan, T.M.; Freeman, M.; Abouelezz, H.; Royar, Kim; Howard, A.; Mickey, R.

2011-01-01

We demonstrate how home range and habitat use analysis can inform landscape-scale conservation planning for the bobcat, Lynx rufus, in Vermont USA. From 2005 to 2008, we outfitted fourteen bobcats with GPS collars that collected spatially explicit locations from individuals every 4. h for 3-4. months. Kernel home range techniques were used to estimate home range size and boundaries, and to quantify the utilization distribution (UD), which is a spatially explicit, topographic mapping of how different areas within the home range are used. We then used GIS methods to quantify both biotic (e.g. habitat types, stream density) and abiotic (e.g. slope) resources within each bobcat's home range. Across bobcats, upper 20th UD percentiles (core areas) had 18% less agriculture, 42% less development, 26% more bobcat habitat (shrub, deciduous, coniferous forest, and wetland cover types), and 33% lower road density than lower UD percentiles (UD valleys). For each bobcat, we used Akaike's Information Criterion (AIC) to evaluate and compare 24 alternative Resource Utilization Functions (hypotheses) that could explain the topology of the individual's UD. A model-averaged population-level Resource Utilization Function suggested positive responses to shrub, deciduous, coniferous forest, and wetland cover types within 1. km of a location, and negative responses to roads and mixed forest cover types within 1. km of a location. Applying this model-averaged function to each pixel in the study area revealed habitat suitability for bobcats across the entire study area, with suitability scores ranging between -1.69 and 1.44, where higher values were assumed to represent higher quality habitat. The southern Champlain Valley, which contained ample wetland and shrub habitat, was a concentrated area of highly suitable habitat, while areas at higher elevation areas were less suitable. Female bobcat home ranges, on average, had an average habitat suitability score of near 0, indicating that home ranges consisted of both beneficial and detrimental habitat types. We discuss the application of habitat suitability mapping and home range requirements for bobcat conservation and landscape scale management. ?? 2011.

A Low-Cost GPS GSM/GPRS Telemetry System: Performance in Stationary Field Tests and Preliminary Data on Wild Otters (Lutra lutra)

PubMed Central

Quaglietta, Lorenzo; Martins, Bruno Herlander; de Jongh, Addy; Mira, António; Boitani, Luigi

2012-01-01

Background Despite the increasing worldwide use of global positioning system (GPS) telemetry in wildlife research, it has never been tested on any freshwater diving animal or in the peculiar conditions of the riparian habitat, despite this latter being one of the most important habitat types for many animal taxa. Moreover, in most cases, the GPS devices used have been commercial and expensive, limiting their use in low-budget projects. Methodology/Principal Findings We have developed a low-cost, easily constructed GPS GSM/GPRS (Global System for Mobile Communications/General Packet Radio Service) and examined its performance in stationary tests, by assessing the influence of different habitat types, including the riparian, as well as water submersion and certain climatic and environmental variables on GPS fix-success rate and accuracy. We then tested the GPS on wild diving animals, applying it, for the first time, to an otter species (Lutra lutra). The rate of locations acquired during the stationary tests reached 63.2%, with an average location error of 8.94 m (SD = 8.55). GPS performance in riparian habitats was principally affected by water submersion and secondarily by GPS inclination and position within the riverbed. Temporal and spatial correlations of location estimates accounted for some variation in the data sets. GPS-tagged otters also provided accurate locations and an even higher GPS fix-success rate (68.2%). Conclusions/Significance Our results suggest that GPS telemetry is reliably applicable to riparian and even diving freshwater animals. They also highlight the need, in GPS wildlife studies, for performing site-specific pilot studies on GPS functioning as well as for taking into account eventual spatial and temporal correlation of location estimates. The limited price, small dimensions, and high performance of the device presented here make it a useful and cost-effective tool for studies on otters and other aquatic or terrestrial medium-to-large-sized animals. PMID:22242163

A low-cost GPS GSM/GPRS telemetry system: performance in stationary field tests and preliminary data on wild otters (Lutra lutra).

PubMed

Quaglietta, Lorenzo; Martins, Bruno Herlander; de Jongh, Addy; Mira, António; Boitani, Luigi

2012-01-01

Despite the increasing worldwide use of global positioning system (GPS) telemetry in wildlife research, it has never been tested on any freshwater diving animal or in the peculiar conditions of the riparian habitat, despite this latter being one of the most important habitat types for many animal taxa. Moreover, in most cases, the GPS devices used have been commercial and expensive, limiting their use in low-budget projects. We have developed a low-cost, easily constructed GPS GSM/GPRS (Global System for Mobile Communications/General Packet Radio Service) and examined its performance in stationary tests, by assessing the influence of different habitat types, including the riparian, as well as water submersion and certain climatic and environmental variables on GPS fix-success rate and accuracy. We then tested the GPS on wild diving animals, applying it, for the first time, to an otter species (Lutra lutra). The rate of locations acquired during the stationary tests reached 63.2%, with an average location error of 8.94 m (SD = 8.55). GPS performance in riparian habitats was principally affected by water submersion and secondarily by GPS inclination and position within the riverbed. Temporal and spatial correlations of location estimates accounted for some variation in the data sets. GPS-tagged otters also provided accurate locations and an even higher GPS fix-success rate (68.2%). Our results suggest that GPS telemetry is reliably applicable to riparian and even diving freshwater animals. They also highlight the need, in GPS wildlife studies, for performing site-specific pilot studies on GPS functioning as well as for taking into account eventual spatial and temporal correlation of location estimates. The limited price, small dimensions, and high performance of the device presented here make it a useful and cost-effective tool for studies on otters and other aquatic or terrestrial medium-to-large-sized animals.

Interaction location outweighs the competitive advantage of numerical superiority in Cebus capucinus intergroup contests.

PubMed

Crofoot, Margaret C; Gilby, Ian C; Wikelski, Martin C; Kays, Roland W

2008-01-15

Numerical superiority confers a competitive advantage during contests among animal groups, shaping patterns of resource access, and, by extension, fitness. However, relative group size does not always determine the winner of intergroup contests. Smaller, presumably weaker social groups often defeat their larger neighbors, but how and when they are able to do so remains poorly understood. Models of competition between individuals suggest that location may influence contest outcome. However, because of the logistical difficulties of studying intergroup interactions, previous studies have been unable to determine how contest location and group size interact to shape relationships among groups. We address this question by using an automated radio telemetry system to study intergroup interactions among six capuchin monkey (Cebus capucinus) social groups of varying sizes. We find that the odds of winning increase with relative group size; one additional group member increases the odds of winning an interaction by 10%. However, this effect is not uniform across space; with each 100 m that a group moves away from the center of its home range, its odds of winning an interaction decrease by 31%. We demonstrate that contest outcome depends on an interaction between group size and location, such that small groups can defeat much larger groups near the center of their home range. The tendency of resident groups to win contests may help explain how small groups persist in areas with intense intergroup competition.

16 CFR 642.3 - Prescreen opt-out notice.

Code of Federal Regulations, 2014 CFR

2014-01-01

... size that is larger than the type size of the principal text on the same page, but in no event smaller than 12-point type, or if provided by electronic means, then reasonable steps shall be taken to ensure that the type size is larger than the type size of the principal text on the same page; (ii) On the...

16 CFR 642.3 - Prescreen opt-out notice.

Code of Federal Regulations, 2013 CFR

2013-01-01

... size that is larger than the type size of the principal text on the same page, but in no event smaller than 12-point type, or if provided by electronic means, then reasonable steps shall be taken to ensure that the type size is larger than the type size of the principal text on the same page; (ii) On the...

16 CFR 642.3 - Prescreen opt-out notice.

Code of Federal Regulations, 2011 CFR

2011-01-01

... size that is larger than the type size of the principal text on the same page, but in no event smaller than 12-point type, or if provided by electronic means, then reasonable steps shall be taken to ensure that the type size is larger than the type size of the principal text on the same page; (ii) On the...

Pathology of breast cancer in women irradiated for acute postpartum mastitis. [X rays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dvoretsky, P.M.; Woodard, E.; Bonfiglio, T.A.

1980-11-15

The gross and microscopic pathology of breast cancers in women irradiated for acute postpartum mastitis was compared to the breast cancers found in the sisters of the irradiated women. In considering the lesions in the two populations, the size, location, histologic type, histologic grade, inflammatory response, lymphatic and blood vascular invasion, nipple involvement, axillary lymph node metastases, and menopausal status at the time of diagnosis were statistically indistinguishable. The only parameter that was different in the two populations was the desmoplastic response to the malignant lesion. The control population had more marked fibrosis within the cancers compared with the irradiatedmore » women.« less

Church ownership and hospital efficiency.

PubMed

White, K R; Ozcan, Y A

1996-01-01

Using a sample of California hospitals, the effect of church ownership was examined as it relates to nonprofit hospital efficiency. Efficiency scores were computed using a nonparametric method called data envelopment analysis (DEA). Controlling for hospital size, location, system membership, and type of church ownership, church-owned hospitals were found to be more frequently in the efficient category than their secular nonprofit counterparts. The outcomes have policy implications for reducing healthcare expenditures by focusing on increasing outputs or decreasing inputs, as appropriate, and bolstering the case for church-sponsored hospitals to retain the tax-exempt status due to their ability to manage their resources as efficiently as (or more efficiently than) secular hospitals.

Inventory of forest and rangeland and detection of forest stress

NASA Technical Reports Server (NTRS)

Heller, R. C.; Aldrich, R. C.; Weber, F. P.; Driscoll, R. S. (Principal Investigator)

1972-01-01

There are no author-identified significant results in this report. Some ERTS-1 imagery has been received for each of the test sites: Black Hills, Atlanta, and Manitou. Only small portions of each site are covered and clouds have precluded capturing good imagery over the center of each site. Discoloration infestations of ponderosa pine are being located and sized on CIR transparencies. A computer program was completed from microdensitometer scans of CIR photos which maps areas of an image which are spectrally similar. Decided differences between forest types are present as well as differences between forest and other vegetative and nonvegetative land classes.

Analysis of the quality of image data acquired by the LANDSAT-4 thematic mapper and multispectral scanners. [Central Valley, California

NASA Technical Reports Server (NTRS)

Colwell, R. N. (Principal Investigator)

1983-01-01

Image products and numeric data were extracted from both TM and MSS data in an effort to evaluate the quality of these data for interpreting major agricultural resources and conditions in California's Central Valley. The utility of TM data appears excellent for meeting most of the inventory objectives of the agricultural resource specialist. These data should be extremely valuable for crop type and area proportion estimation, for updating agricultural land use survey maps at 1:24,000-scale and smaller, for field boundary definition, and for determining the size and location of individual farmsteads.

Endodontic management of an unusual foreign body in a maxillary central incisor.

PubMed

Chand, Keerthi; Joesph, Sam; Varughese, Jolly Mary; Nair, Mali G; Prasanth, Santhosh

2013-09-01

The discovery of foreign bodies in the teeth is often diagnosed accidentally. It is commonly seen in children. These foreign objects may act as a potential source of infection and may later lead to a painful condition. Detailed case history, clinical and radiographic examinations are necessary to come to a conclusion about the nature, size, and location of the foreign body, and the difficulty involved in its retrieval. This paper discusses the types of foreign objects found in and around the teeth and reports an unusual case of a stapler pin in the root canal of a tooth, its retrieval, and associated management of the involved teeth.

A new cardiology patient simulator.

PubMed

Takashina, T; Shimizu, M; Katayama, H

1997-01-01

We report a new cardiology patient simulator developed through the application of new digital computer technology, capable of playing back selected physical findings (jugular-venous waves, arterial pulses of carotid, brachial, radial and femoral arteries, and cardiac impulses), as well as cardiac sounds, murmurs and respiratory sounds that have been prerecorded from actual patients. The examining physician uses an ordinary type of stethoscope. Four built-in speakers are located in the human-sized mannequin at the classic auscultatory sites (aortic, pulmonic, tricuspid and mitral). This compact and portable educational apparatus should facilitate medical training in the bedside cardiac examination, of physicians, medical students, nurses and paramedics throughout the world.

Imaging the in-plane distribution of helium precipitates at a Cu/V interface

DOE PAGES

Chen, Di; Li, Nan; Yuryev, Dina; ...

2017-02-15

Here, we describe a transmission electron microscopy investigation of the distribution of helium precipitates within the plane of an interface between Cu and V. Statistical analysis of precipitate locations reveals a weak tendency for interfacial precipitates to align alongmore » $$\\langle$$110$$\\rangle$$-type crystallographic directions within the Cu layer. Comparison of these findings with helium-free Cu/V interfaces suggests that the precipitates may be aggregating preferentially along atomic-size steps in the interface created by threading dislocations in the Cu layer. Our observations also suggest that some precipitates may be aggregating along intersections between interfacial misfit dislocations.« less

Design concepts for low-cost composite engine frames

NASA Technical Reports Server (NTRS)

Chamis, C. C.

1983-01-01

Design concepts for low-cost, lightweight composite engine frames were applied to the design requirements for the frame of commercial, high-bypass turbine engines. The concepts consist of generic-type components and subcomponents that could be adapted for use in different locations in the engine and to different engine sizes. A variety of materials and manufacturing methods were assessed with a goal of having the lowest number of parts possible at the lowest possible cost. The evaluation of the design concepts resulted in the identification of a hybrid composite frame which would weigh about 70 percent of the state-of-the-art metal frame and cost would be about 60 percent.

Comparison of implant component fractures in external and internal type: A 12-year retrospective study.

PubMed

Yi, Yuseung; Koak, Jai-Young; Kim, Seong-Kyun; Lee, Shin-Jae; Heo, Seong-Joo

2018-04-01

The aim of this study was to compare the fracture of implant component behavior of external and internal type of implants to suggest directions for successful implant treatment. Data were collected from the clinical records of all patients who received WARANTEC implants at Seoul National University Dental Hospital from February 2002 to January 2014 for 12 years. Total number of implants was 1,289 and an average of 3.2 implants was installed per patient. Information about abutment connection type, implant locations, platform sizes was collected with presence of implant component fractures and their managements. SPSS statistics software (version 24.0, IBM) was used for the statistical analysis. Overall fracture was significantly more frequent in internal type. The most frequently fractured component was abutment in internal type implants, and screw fracture occurred most frequently in external type. Analyzing by fractured components, screw fracture was the most frequent in the maxillary anterior region and the most abutment fracture occurred in the maxillary posterior region and screw fractures occurred more frequently in NP (narrow platform) and abutment fractures occurred more frequently in RP (regular platform). In external type, screw fracture occurred most frequently, especially in the maxillary anterior region, and in internal type, abutment fracture occurred frequently in the posterior region. placement of an external type implant rather than an internal type is recommended for the posterior region where abutment fractures frequently occur.

Deep Landslides in flysch formations

NASA Astrophysics Data System (ADS)

Marinos, Vassilis

2017-04-01

Flysch, linked with the tectonic development of an area, has suffered from compressional forces being highly deformed by thrust faults and folds, containing thus often tectonically pre-sheared zones of various size. These geological characteristics may produce weak to very weak rock masses which may present instability and landslides in both mountain and local slope scale. The paper mainly discusses the "mountain" scale phenomena. The size of these masses can reach hundreds of meters in both depth and width on the valley sides. A brief presentation of the flysch formation is presented. A typology is presented with 11 types of flysch, depending on the persistence and participation or not of the strong members (as sandstones) against the weak ones (as siltstones, shales) and the degree and scale of tectonic disturbance. These rock mass types are connected with the landslide mechanism. In all cases the tectonic conditions of a broader area are responsible and the establishment of the tectonic-paleogeographic model is necessary before the conceptual study and design of any major infrastructure work and the choice of its alignment or location. Given the size of such instability areas remedial measures are in most cases not feasible and the realignment or relocation from the initial plans are often the only solution. Cases from highways and pipelines in Greek and Albanian territory are presented. A large number of information from lab tests, geotechnical classifications and back analyses collected from a wide variety of flysch formations is presented and discussed.

Population status, demography and habitat preferences of the threatened lipstick palm Cyrtostachys renda Blume in Kerumutan Reserve, Sumatra

NASA Astrophysics Data System (ADS)

Widyatmoko, Didik; Burgman, Mark A.; Guhardja, Edi; Mogea, Johanis P.; Walujo, Eko B.; Setiadi, Dede

2005-09-01

Population status and demography of a population of the threatened lipstick palm Cyrtostachys renda in a peat swamp ecosystem of Kerumutan Reserve, Sumatra (one of the largest remaining populations) was documented at 16 different sites, covering a wide range of forest and habitat types, vegetation associations, and population sizes. Population sizes were dominated by suckers comprising 89% of the total population. Individuals with stem heights between 0 and 4 m (47.5%), stem diameters between 4 and 10 cm (82.0%), and leaf scar numbers between 0 and 60 (69.2%) dominated. Ages of individuals were estimated and used to fit a curvilinear relationship between age and stem height. Wild plants reach reproductive maturity within 25-30 years, or when they have stem heights in excess of 2.0 m, or when they have 15-25 leaf scars. They can survive more than 80 years. Cultivated plants appear to reproduce earlier and produce more seeds than wild plants. Individual growth was plant size-dependent with the adult stage being the most productive. Higher mortality was experienced by suckers, especially in continuously waterlogged conditions and locations with dense canopies. Sucker growth was faster than seedling growth, an adaptation that may allow the species to cope with periodically waterlogged conditions. Population abundances varied with habitat types; well-drained areas were the most suitable habitat. To conserve the most important remaining populations of the lipstick palm, it is crucial to protect well-drained sites in Kerumutan Reserve.

Low is large: spatial location and pitch interact in voice-based body size estimation.

PubMed

Pisanski, Katarzyna; Isenstein, Sari G E; Montano, Kelyn J; O'Connor, Jillian J M; Feinberg, David R

2017-05-01

The binding of incongruent cues poses a challenge for multimodal perception. Indeed, although taller objects emit sounds from higher elevations, low-pitched sounds are perceptually mapped both to large size and to low elevation. In the present study, we examined how these incongruent vertical spatial cues (up is more) and pitch cues (low is large) to size interact, and whether similar biases influence size perception along the horizontal axis. In Experiment 1, we measured listeners' voice-based judgments of human body size using pitch-manipulated voices projected from a high versus a low, and a right versus a left, spatial location. Listeners associated low spatial locations with largeness for lowered-pitch but not for raised-pitch voices, demonstrating that pitch overrode vertical-elevation cues. Listeners associated rightward spatial locations with largeness, regardless of voice pitch. In Experiment 2, listeners performed the task while sitting or standing, allowing us to examine self-referential cues to elevation in size estimation. Listeners associated vertically low and rightward spatial cues with largeness more for lowered- than for raised-pitch voices. These correspondences were robust to sex (of both the voice and the listener) and head elevation (standing or sitting); however, horizontal correspondences were amplified when participants stood. Moreover, when participants were standing, their judgments of how much larger men's voices sounded than women's increased when the voices were projected from the low speaker. Our results provide novel evidence for a multidimensional spatial mapping of pitch that is generalizable to human voices and that affects performance in an indirect, ecologically relevant spatial task (body size estimation). These findings suggest that crossmodal pitch correspondences evoke both low-level and higher-level cognitive processes.

Relationship between knee pain and the presence, location, size and phenotype of femorotibial denuded areas of subchondral bone as visualized by MRI.

PubMed

Cotofana, S; Wyman, B T; Benichou, O; Dreher, D; Nevitt, M; Gardiner, J; Wirth, W; Hitzl, W; Kwoh, C K; Eckstein, F; Frobell, R B

2013-09-01

Conflicting associations between imaging biomarkers and pain in knee osteoarthritis (OA) have been reported. A relation between pain and denuded areas of subchondral bone (dABs) has been suggested and this study explores this relationship further by relating the presence, phenotype, location and size of dABs to different measures of knee pain. 633 right knees from the Osteoarthritis Initiative (OAI) (250 men, age 61.7 ± 9.6 yrs, BMI 29.4 ± 4.7 kg/m(2)) were included. Manual segmentation of the femorotibial cartilage plates was performed on 3 T coronal fast low angle shot with water excitation (FLASHwe) images. dABs were defined as areas where the subchondral bone was uncovered by cartilage. The following measures of pain were used: weightbearing-, non-weightbearing-, moderate-to-severe-, infrequent- and frequent knee pain. Using pain measures from subjects without dABs as a reference, those with at least one dAB had a 1.64-fold higher prevalence ratio [PR, 95% confidence interval (CI) 1.24-2.18] to have frequent and 1.45-fold higher for moderate-to-severe knee pain (95% CI 1.13-1.85). Subjects with dABs in central subregions had a 1.53-fold increased prevalence of having weightbearing pain (95% CI 1.20-1.97), especially when the central subregion was moderately (>10%) denuded (PR 1.81, 95% CI 1.35-2.42). Individuals with cartilage-loss-type dABs had a slightly higher prevalence (PR 1.13, 95% CI 1.00-1.27) of having frequent knee pain compared to individuals with intra-chondral-osteophyte-type dABs. This study supports a positive relation between femorotibial dABs and knee pain, especially when the dABs are located centrally (i.e., in weightbearing regions) or when the respective central subregion is moderately denuded. Copyright © 2013 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Factors affecting the bacterial community composition and heterotrophic production of Columbia River estuarine turbidity maxima.

PubMed

Herfort, Lydie; Crump, Byron C; Fortunato, Caroline S; McCue, Lee Ann; Campbell, Victoria; Simon, Holly M; Baptista, António M; Zuber, Peter

2017-12-01

Estuarine turbidity maxima (ETM) function as hotspots of microbial activity and diversity in estuaries, yet, little is known about the temporal and spatial variability in ETM bacterial community composition. To determine which environmental factors affect ETM bacterial populations in the Columbia River estuary, we analyzed ETM bacterial community composition (Sanger sequencing and amplicon pyrosequencing of 16S rRNA gene) and bulk heterotrophic production ( 3 H-leucine incorporation rates). We collected water 20 times to cover five ETM events and obtained 42 samples characterized by different salinities, turbidities, seasons, coastal regimes (upwelling vs. downwelling), locations, and particle size. Spring and summer populations were distinct. All May samples had similar bacterial community composition despite having different salinities (1-24 PSU), but summer non-ETM bacteria separated into marine, freshwater, and brackish assemblages. Summer ETM bacterial communities varied depending on coastal upwelling or downwelling conditions and on the sampling site location with respect to tidal intrusion during the previous neap tide. In contrast to ETM, whole (>0.2 μm) and free-living (0.2-3 μm) assemblages of non-ETM waters were similar to each other, indicating that particle-attached (>3 μm) non-ETM bacteria do not develop a distinct community. Brackish water type (ETM or non-ETM) is thus a major factor affecting particle-attached bacterial communities. Heterotrophic production was higher in particle-attached than free-living fractions in all brackish waters collected throughout the water column during the rise to decline of turbidity through an ETM event (i.e., ETM-impacted waters). However, free-living communities showed higher productivity prior to or after an ETM event (i.e., non-ETM-impacted waters). This study has thus found that Columbia River ETM bacterial communities vary based on seasons, salinity, sampling location, and particle size, with the existence of three particle types characterized by different bacterial communities in ETM, ETM-impacted, and non-ETM-impacted brackish waters. Taxonomic analysis suggests that ETM key biological function is to remineralize organic matter. © 2017 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

Type, origin, and reservoir characteristics of dolostones of the Ordovician Majiagou Group, Ordos, North China Platform

NASA Astrophysics Data System (ADS)

Feng Zengzhao; Zhang Yongsheng; Jin Zhenkui

1998-06-01

Dolostones are well developed in the Ordovician Majiagou Group in the Ordos area, North China Platform. These dolostones can be divided into four types: mud-sized to silt-sized crystalline dolostones not associated with gypsum and halite beds (type I), mud-sized to silt-sized crystalline dolostones associated with gypsum and halite beds (type II), mottled silt-sized to very fine sand-sized crystalline dolostones (fine saccharoidal dolostones) (type III), and mottled coarse silt-sized to fine sand-sized crystalline dolostones (coarse saccharoidal dolostones) (type IV). Type I dolostones consist of mud-sized to silt-sized dolomite crystals. Laminar stromatolites, ripple marks, mud cracks and birdseyes are common. Such dolostones are not associated with gypsum and halite beds, but lath-shaped pseudomorphs after gypsum are common. The ordering of dolomites averages 0.59, and molar concentration of CaCO 3 averages 51.44%. δ13C averages -0.8‰ (PDB Standard), δ18O averages -2.9‰, δCe averages 0.83. The above characteristics suggest that type I dolostones result from penecontemporaneous dolomitization of lime mud on supratidal flat environments by hypersaline sea water. Type II dolostones mainly consist of mud-sized to silt-sized dolomite crystals. They are commonly well laminated but show no desiccation structures. Such dolostones are intercalated within laminated gypsum and halite beds or are intermixed with them. Such dolostones resulted from dolomitization of lime mud by hypersaline sea water in gypsum and halite precipitating lagoons. Type III dolostones consist of coarse silt-sized to very fine sand-sized dolomite crystals. They commonly underlie type I dolostones and grade downwards to dolomite-mottled limestones and pure limestones. The ordering of dolomites averages 0.63, and molar concentration of CaCO 3 averages 55.64%. δ13C averages -0.2‰, δ18O averages -3.3‰, δCe averages 1.24. Such dolostones resulted from reflux dolomitization by hypersaline sea water. Type IV dolostones consist of coarse-silt-sized to fine-sand-sized dolomite crystals. In such dolostones, stylolites are cut by dolomite crystals. Fluid inclusions are present, and the homogenization temperature commonly ranges from 104°C to 203°C. The ordering of dolomites averages 0.85, and molar concentration of CaCO 3 averages 50.65%. δ13C averages 0.6‰, δ18O averages -7.4‰, and δCe averages 1.16. Such dolostones resulted from deep burial dolomitization. In the Ordos area, type I and II dolostones modified by palaeokarstification are the major gas reservoir rocks of the Ordos Gas Field at present. Type IV dolostones show good reservoir characteristics and may also be potential reservoir rocks.

Hydrologic Controls on Shallow Landslide Location, Size, and Shape

NASA Astrophysics Data System (ADS)

Bellugi, D.; Milledge, D.; Perron, T.; McKean, J. A.; Dietrich, W.; Rulli, M.

2012-12-01

Shallow landslides, typically involving just the soil mantle, are principally controlled by topography, soil and root strengths, and soil thickness, and are typically triggered by storm-induced increases in pore water pressure. The response of a landscape to landslide-triggering storms will thus depend on factors such as rainfall totals, storm intensity and duration, and antecedent moisture conditions. The two dominant mechanisms that generate high pore water pressures at a point are topographically-steered lateral subsurface flow (over timescales of days to weeks), and rapid vertical infiltration (over timescales of minutes to hours). We aim to understand the impact of different storm characteristics and hydrologic regimes on shallow landslide location, size, and shape. We have developed a regional-scale model, which applies a low-parameter grid-based multi-dimensional slope stability model within a novel search algorithm, to generate discrete landslide predictions. This model shows that the spatial organization of parameters such as root strength and pore water pressure has a strong control on shallow landslide location, size, and shape. We apply this model to a field site near Coos Bay, OR, where a ten-year landslide inventory has been mapped onto high-resolution topographic data. Our model predicts landslide size generally increases with increasing rainfall intensity, except when root strength is extremely high and pore pressures are topographically steered. The distribution of topographic index values (the ratios of contributing area to slope) of predicted landslides is a clear signature of the pore water pressure generation mechanism: as laterally dominated flow increases, landslides develop in locations with lower slopes and higher contributing areas; in contrast, in the case of vertically-dominated pore pressure rise, landslides are consistently found in locations with higher slopes and lower contributing areas. While in both cases landslides are found in the hollows, where the soils are sufficiently deep to overcome the effects of root strength, in the laterally-dominated case they are predicted to occur further down the hollows (which matches field observations). The size distribution of landslides is better predicted in our model when vertical infiltration dominates, but the observed distribution of topographic index values follows that predicted when lateral flow dominates. This suggests that both mechanisms must be taken into account in order to capture both location and size of shallow landslides (consistent with field observations). These results suggest that this modeling approach could allow us to use observed landslide locations and geometries to infer the dominant hydrologic triggering mechanisms. Furthermore, as the spatial and temporal resolution of precipitation forecasting improves, this model will enable us to more accurately predict both location and size of shallow landslides.

Slow Narrow Spectral Width E Region Echoes Observed During the March 17-2015 Storm and What They Reveal About the Disturbed Ionosphere.

NASA Astrophysics Data System (ADS)

St-Maurice, J. P.; Chau, J. L.

2015-12-01

As auroral-type disturbances moved equatorward during the March 17-2015 storm, coherent E region echoes were observed simultaneously with three radar links separated by 40 km each in the east-west direction in northern Germany. One radar operated at 36.2, and the other two at 32.55 MHz. One of the latter operated in a bistatic configuration. On each radar site five separate antennas were used to locate the echoes using interferometry. The unique configuration provided an unsurpassed opportunity to study the origin and evolution of ionospheric structures in a wide field of view during a strong storm. A most noticeable feature was that over a few time intervals, several minutes in duration each, very narrow spectra were observed, with Doppler shifts roughly 1/2 the ion-acoustic speed (often called "type III" echoes in the past). The inferred location indicated that the echoes came from below 100 km altitude. Echoes moving at the nominal ion-acoustic speed came from higher up and/or different flow angles. In one particularly clear instance the "Type III" echo region came from a region 50 to 75 km in extent drifting at roughly 1.5 km/s, while moving at some small (but non-zero) flow angle with respect to the line-of-sight. In view of the observations, a reevaluation of existing theories indicates that the echoes cannot be related to ion cyclotron waves. Instead, their low altitude and flow angle dependence reveal that they are the by-product of the ion Pedersen instability, which has been investigated by a few groups in relation to a non-isothermal treatment of the Farley-Buneman instability. In our present treatment of the problem, nonlinear effects are invoked to compute the final Doppler shift of the resulting structures. We find that the stronger the electric field is, the closer the region of slow echoes has to be to the ExB direction. In our most dramatic example of Type III structures, the size of the echo region pointed to a region of high energy precipitation 50 km by 50 km in size which was moving at a speed of 1.5 km/s. Without the high energy precipitation, there would have been no plasma produced below 100 km and therefore no "Type III" echoes. The high energy precipitation inference is reminiscent of previous "Type III" radar observations that associated their occurrence with regions of auroral precipitation.

Inpatient admissions from the ED for adults with injuries: the role of clinical and nonclinical factors.

PubMed

Spector, William D; Limcangco, Rhona; Mutter, Ryan L; Pines, Jesse M; Owens, Pamela

2015-06-01

Inpatient hospital costs represent nearly a third of heath care spending. The proportion of inpatients visits that originate in the emergency department (ED) has been growing, approaching half of all inpatient admissions. Injury is the most common reason for adult ED visits, representing nearly one-quarter of all ED visits. The objective was to explore the association of clinical and nonclinical factors with the decision to admit ED patients with injury. This is a retrospective cohort study of injury-related ED encounters by adults in select states in 2009. We limited the study to ED visits of persons with moderately severe injuries. We used logistic regression to calculate the marginal effects, estimating 4 equations to account for different risk patterns for older and younger adults, and types of injuries. Regression models controlled for comorbidities, injury characteristics, demographic characteristics, and state fixed effects. Injury location, type, and mechanism and comorbidities had large effects on hospitalization rates as expected. We found higher inpatient admission rates by level of trauma center designation and hospital size, but findings differed by age and type of injury. For younger adults, patients with private insurance and patients who traveled more than 30 miles were more likely to be admitted. There is great variation in inpatient admission decisions for moderately injured patients in the ED. Decisions appear to be dominated by clinical factors such as injury characteristics and comorbidities; however, nonclinical factors, such as type of insurance, hospital size, and trauma center designation, also play an important role. Published by Elsevier Inc.

Wildlife habitat management on college and university campuses

USGS Publications Warehouse

Bosci, Tierney; Warren, Paige S.; Harper, Rick W.; DeStefano, Stephen

2018-01-01

With the increasing involvement of higher education institutions in sustainability movements, it remains unclear to what extent college and university campuses address wildlife habitat. Many campuses encompass significant areas of green space with potential to support diverse wildlife taxa. However, sustainability rating systems generally emphasize efforts like recycling and energy conservation over green landscaping and grounds maintenance. We sought to examine the types of wildlife habitat projects occurring at schools across the United States and whether or not factors like school type (public or private), size (number of students), urban vs. rural setting, and funding played roles in the implementation of such initiatives. Using case studies compiled by the National Wildlife Federation’s Campus Ecology program, we documented wildlife habitat-related projects at 60 campuses. Ten management actions derived from nationwide guidelines were used to describe the projects carried out by these institutions, and we recorded data about cost, funding, and outreach and education methods. We explored potential relationships among management actions and with school characteristics. We extracted themes in project types, along with challenges and responses to those challenges. Native plant species selection and sustainable lawn maintenance and landscaping were the most common management actions among the 60 campuses. According to the case studies we examined, we found that factors like school type, size, and location did not affect the engagement of a campus in wildlife habitat initiatives, nor did they influence the project expenditures or funding received by a campus. Our results suggest that many wildlife habitat initiatives are feasible for higher education institutions and may be successfully implemented at relatively low costs through simple, but deliberate management actions.

[Management of cerebrospinal fluid leaks according to size. Our experience].

PubMed

Alobid, Isam; Enseñat, Joaquim; Rioja, Elena; Enriquez, Karla; Viscovich, Liza; de Notaris, Matteo; Bernal-Sprekelsen, Manuel

2014-01-01

We present our experience in the reconstruction of cerebrospinal fluid (CSF) leaks according to their size and location. Fifty-four patients who underwent advanced skull base surgery (large defects) and 62 patients with CSF leaks of different origin (small and medium-sized defects) were included. Large defects were reconstructed with a nasoseptal pedicled flap positioned on fat and fascia lata and lumbar drainage was used. In small and medium-sized leaks of other origin, intrathecal fluorescein 5% was applied previously to identify the defect. Fascia lata in an underlay position was used for reconstruction, which was then covered with mucoperiosteum from the turbinate. Perioperative antibiotics were administered for 5-7 days. Nasal packing was removed after 24-48 hours. The most frequent aetiology for small and medium-sized defects was spontaneous (48.4%), followed by trauma (24.2%), iatrogenic (5%) and others. The success rate was of 91% after the first surgery and 98% in large skull base defects and small/medium-sized respectively. After rescue surgery, the rate of closure achieved was 100%. The follow-up was 15.6 ± 12.4 months for large defects and 75.3 ± 51.3 months for small/medium-sized defects without recurrence. Endoscopic surgery for closure of any type of skull base defect is the gold standard approach. Defect size does not play a significant role in the success rate. Fascia lata and mucoperiosteum allow a reconstruction of small/medium-sized defects. For larger skull base defects, a combination of fat, fascia lata and nasoseptal pedicled flaps provide a successful reconstruction. Copyright © 2013 Elsevier España, S.L. All rights reserved.

Effect of Lump Size and Nodal Status on Prognosis in Invasive Breast Cancer: Experience from Rural India

PubMed Central

Garg, Monique; Sidhu, Darshan Singh; Singh, Amandeep

2016-01-01

Introduction Breast cancer is now the leading cause of cancer among Indian women. Usually large tumour size and axillary lymph node involvement are linked with adverse outcome and this notion forms the basis of screening programs i.e. early detection. Aim The present study was carried out to analyse relationship between tumour size, lymph node status and there relation with outcome after treatment. Materials and Methods Fifty patients with cytology-proven invasive breast tumours were evaluated for size, clinical and pathologic characteristics of tumour, axillary lymph node status and outcome data recorded on sequential follow-up. Results Mean age of all participated patients was 52.24±10 years. Most common tumour location was in the upper outer quadrant with mean size of primary tumour being 3.31±1.80cm. On pathology number of lymph nodes examined ranged from 10 to 24 and 72% of patients recorded presence of disease in axilla. Significant positive correlation (p<0.013; r2=0.026) between tumour size and axillary lymph node involvement on linear regression. Also an indicative correlation between size and grade of tumour and axillary lymph node status was found with survival from the disease. Conclusion The present study highlights that the size of the primary tumour and the number of positive lymph nodes have an inverse linear relationship with prognosis. Despite advances in diagnostic modalities, evolution of newer markers and genetic typing both size of tumour as T and axillary lymphadenopathy as N form an integral part of TNM staging and are of paramount importance for their role in treatment decisions and illustrate prognosis in patients with invasive breast cancer. PMID:27504343

34 CFR 300.616 - List of types and locations of information.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 2 2010-07-01 2010-07-01 false List of types and locations of information. 300.616... EDUCATION OF CHILDREN WITH DISABILITIES Monitoring, Enforcement, Confidentiality, and Program Information Confidentiality of Information § 300.616 List of types and locations of information. Each participating agency...

Shape-memory polymer foam device for treating aneurysms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortega, Jason M.; Benett, William J.; Small, Ward

A system for treating an aneurysm in a blood vessel or vein, wherein the aneurysm has a dome, an interior, and a neck. The system includes a shape memory polymer foam in the interior of the aneurysm between the dome and the neck. The shape memory polymer foam has pores that include a first multiplicity of pores having a first pore size and a second multiplicity of pores having a second pore size. The second pore size is larger than said first pore size. The first multiplicity of pores are located in the neck of the aneurysm. The second multiplicitymore » of pores are located in the dome of the aneurysm.« less

Abundance and distribution of microplastics within surface sediments of a key shellfish growing region of Canada.

PubMed

Kazmiruk, T N; Kazmiruk, V D; Bendell, L I

2018-01-01

The abundance and distribution of microplastics within 5 sediment size classes (>5000 μm, 1000-5000 μm, 250-1000 μm, 250-0.63 μm and < 0.63 μm) were determined for 16 sites within Lambert Channel and Baynes Sound, British Columbia, Canada. This region is Canada's premier growing area for the Pacific oyster (Crassostrea gigas). Microplastics were found at all sampling locations indicating widespread contamination of this region with these particles. Three types of microplastics were recovered: microbeads, which occurred in the greatest number (up to 25000/kg dry sediment) and microfibers and microfragments, which were much less in number compared with microbeads and occurred in similar amounts (100-300/kg dry sediment). Microbeads were recovered primarily in the < 0.63 μm and 250-0.63 μm sediment size class, whereas microfragments and microfibers were generally identified in all 5 sediment size classes. Abundance and distribution of the three types of microplastics were spatially dependent with principal component analysis (PCA) indicating that 84 percent of the variation in abundance and distribution was due to the presence of high numbers of microbeads at three locations within the study region. At these sites, microbeads expressed as a percent component of the sediment by weight was similar to key geochemical components that govern trace metal behavior and availability to benthic organisms. Microbeads have been shown to accumulate metals from the aquatic environment, hence in addition to the traditional geochemical components such as silt and organic matter, microplastics also need to be considered as a sediment component that can influence trace metal geochemistry. Our findings have shown that BC's premier oyster growing region is highly contaminated with microplastics, notably microbeads. It would be prudent to assess the degree to which oysters from this region are ingesting microplastics. If so, it would have direct implications for Canada's oyster farming industry with respect to the health of the oyster and the quality of product that is being farmed and sets an example for other shellfish growing regions of the world.

Abundance and distribution of microplastics within surface sediments of a key shellfish growing region of Canada

PubMed Central

Kazmiruk, T. N.; Kazmiruk, V. D.

2018-01-01

The abundance and distribution of microplastics within 5 sediment size classes (>5000 μm, 1000–5000 μm, 250–1000 μm, 250–0.63 μm and < 0.63 μm) were determined for 16 sites within Lambert Channel and Baynes Sound, British Columbia, Canada. This region is Canada’s premier growing area for the Pacific oyster (Crassostrea gigas). Microplastics were found at all sampling locations indicating widespread contamination of this region with these particles. Three types of microplastics were recovered: microbeads, which occurred in the greatest number (up to 25000/kg dry sediment) and microfibers and microfragments, which were much less in number compared with microbeads and occurred in similar amounts (100–300/kg dry sediment). Microbeads were recovered primarily in the < 0.63 μm and 250–0.63 μm sediment size class, whereas microfragments and microfibers were generally identified in all 5 sediment size classes. Abundance and distribution of the three types of microplastics were spatially dependent with principal component analysis (PCA) indicating that 84 percent of the variation in abundance and distribution was due to the presence of high numbers of microbeads at three locations within the study region. At these sites, microbeads expressed as a percent component of the sediment by weight was similar to key geochemical components that govern trace metal behavior and availability to benthic organisms. Microbeads have been shown to accumulate metals from the aquatic environment, hence in addition to the traditional geochemical components such as silt and organic matter, microplastics also need to be considered as a sediment component that can influence trace metal geochemistry. Our findings have shown that BC’s premier oyster growing region is highly contaminated with microplastics, notably microbeads. It would be prudent to assess the degree to which oysters from this region are ingesting microplastics. If so, it would have direct implications for Canada’s oyster farming industry with respect to the health of the oyster and the quality of product that is being farmed and sets an example for other shellfish growing regions of the world. PMID:29791448

3D-HST+CANDELS: The Evolution of the Galaxy Size-Mass Distribution since z = 3

NASA Astrophysics Data System (ADS)

van der Wel, A.; Franx, M.; van Dokkum, P. G.; Skelton, R. E.; Momcheva, I. G.; Whitaker, K. E.; Brammer, G. B.; Bell, E. F.; Rix, H.-W.; Wuyts, S.; Ferguson, H. C.; Holden, B. P.; Barro, G.; Koekemoer, A. M.; Chang, Yu-Yen; McGrath, E. J.; Häussler, B.; Dekel, A.; Behroozi, P.; Fumagalli, M.; Leja, J.; Lundgren, B. F.; Maseda, M. V.; Nelson, E. J.; Wake, D. A.; Patel, S. G.; Labbé, I.; Faber, S. M.; Grogin, N. A.; Kocevski, D. D.

2014-06-01

Spectroscopic+photometric redshifts, stellar mass estimates, and rest-frame colors from the 3D-HST survey are combined with structural parameter measurements from CANDELS imaging to determine the galaxy size-mass distribution over the redshift range 0 < z < 3. Separating early- and late-type galaxies on the basis of star-formation activity, we confirm that early-type galaxies are on average smaller than late-type galaxies at all redshifts, and we find a significantly different rate of average size evolution at fixed galaxy mass, with fast evolution for the early-type population, R effvprop(1 + z)-1.48, and moderate evolution for the late-type population, R effvprop(1 + z)-0.75. The large sample size and dynamic range in both galaxy mass and redshift, in combination with the high fidelity of our measurements due to the extensive use of spectroscopic data, not only fortify previous results but also enable us to probe beyond simple average galaxy size measurements. At all redshifts the slope of the size-mass relation is shallow, R_{eff}\\propto M_*^{0.22}, for late-type galaxies with stellar mass >3 × 109 M ⊙, and steep, R_{eff}\\propto M_*^{0.75}, for early-type galaxies with stellar mass >2 × 1010 M ⊙. The intrinsic scatter is lsim0.2 dex for all galaxy types and redshifts. For late-type galaxies, the logarithmic size distribution is not symmetric but is skewed toward small sizes: at all redshifts and masses, a tail of small late-type galaxies exists that overlaps in size with the early-type galaxy population. The number density of massive (~1011 M ⊙), compact (R eff < 2 kpc) early-type galaxies increases from z = 3 to z = 1.5-2 and then strongly decreases at later cosmic times.

[Humus composition of black soil and its organo-mineral complexes under different fertility level].

PubMed

Zhao, Lanpo; Wang, Jie; Liu, Jingshuan; Liu, Shuxia; Wang, Yanling; Wang, Hongbin; Zhang, Zhidan

2005-01-01

Determinations by Kumada method showed that with the improvement of black soil fertility, the free and combined humus contents in soil and its different size organo-mineral complexes increased, but the humification degree of free humus decreased, which was more obvious in silt and fine sand size complexes. The organic carbon content in complexes, humus extraction rate, free humus content, and humification degree of free humic acid decreased with the increasing particle size of complexes. All free humic acids in fertile soil were Rp type, while in unfertile soil, they were Rp and B type. With the increasing particle size of complexes, the type of free humic acids changed in the sequence A type (clay)-->B type (silt)-->Rp type (fine sand). Combined form humic acid mainly belonged to A type, no matter what particle size the complex was. The improvement of soil fertility could make the humification degree of free humus in soil and its complexes decrease, and furthermore, result in type change. In black soil, the type change of free humic acid mainly occurred in silt size complex, and that of combined form humic acid mainly occurred in fine sand size complex.

How Do the Location, Size and Budget of Open Space Conservation Affect Land Values?

Treesearch

JunJie Wu; Wenchao Xu; Ralph J. Alig

2016-01-01

In this article we present a model to examine the optimal location, size, and budget of open space conservation and the resulting impact on land values and local fiscal conditions in an urban area. Results indicate that open space conservation can transform the defining features of an urban landscape. A well-designed open space conservation program can improve...

Influence of lidar, Landsat imagery, disturbance history, plot location accuracy, and plot size on accuracy of imputation maps of forest composition and structure

Treesearch

Harold S.J. Zald; Janet L. Ohmann; Heather M. Roberts; Matthew J. Gregory; Emilie B. Henderson; Robert J. McGaughey; Justin Braaten

2014-01-01

This study investigated how lidar-derived vegetation indices, disturbance history from Landsat time series (LTS) imagery, plot location accuracy, and plot size influenced accuracy of statistical spatial models (nearest-neighbor imputation maps) of forest vegetation composition and structure. Nearest-neighbor (NN) imputation maps were developed for 539,000 ha in the...

Differences between dentitions with palatally and labially located maxillary canines observed in incisor width, dental morphology and space conditions.

PubMed

Artmann, L; Larsen, H J; Sørensen, H B; Christensen, I J; Kjaer, I

2010-06-01

To analyze the interrelationship between incisor width, deviations in the dentition and available space in the dental arch in palatally and labially located maxillary ectopic canine cases. Size: On dental casts from 69 patients (mean age 13 years 6 months) the mesiodistal widths of each premolar, canine and incisor were measured and compared with normal standards. Dental deviations: Based on panoramic radiographs from the same patients the dentitions were grouped accordingly: Group I: normal morphology; Group IIa: deviations in the dentition within the maxillary incisors only; Group IIb: deviations in the dentition in general. Descriptive statistics for the tooth sizes and dental deviations were presented by the mean and 95% confidence limits for the mean and the p-value for the T-statistic. Space: Space was expresses by subtracting the total tooth sizes of incisors, canines and premolars from the length of the arch segments. Size of lateral maxillary incisor: The widths of the lateral incisors were significantly different in groups I, IIa and IIb (p=0.016) and in cases with labially located ectopic canines on average 0.65 (95% CI:0.25-1.05, p=0.0019) broader than lateral incisors in cases with palatally located ectopic canines. Space: Least available space was observed in cases with labially located canines. The linear model did show a difference between palatally and labially located ectopic canines (p=0.03). Space related to deviations in the dentition: When space in the dental arch was related to dental deviations (groups I, IIa and IIb), the cases in group IIb with palatally located canines had significantly more space compared with I and IIa. Two subgroups of palatally located ectopic maxillary canine cases based on registration of space, incisor width and deviations in the morphology of the dentition were identified.

A meta-analysis of active video games on health outcomes among children and adolescents.

PubMed

Gao, Z; Chen, S; Pasco, D; Pope, Z

2015-09-01

This meta-analysis synthesizes current literature concerning the effects of active video games (AVGs) on children/adolescents' health-related outcomes. A total of 512 published studies on AVGs were located, and 35 articles were included based on the following criteria: (i) data-based research articles published in English between 1985 and 2015; (ii) studied some types of AVGs and related outcomes among children/adolescents and (iii) had at least one comparison within each study. Data were extracted to conduct comparisons for outcome measures in three separate categories: AVGs and sedentary behaviours, AVGs and laboratory-based exercise, and AVGs and field-based physical activity. Effect size for each entry was calculated with the Comprehensive Meta-Analysis software in 2015. Mean effect size (Hedge's g) and standard deviation were calculated for each comparison. Compared with sedentary behaviours, AVGs had a large effect on health outcomes. The effect sizes for physiological outcomes were marginal when comparing AVGs with laboratory-based exercises. The comparison between AVGs and field-based physical activity had null to moderate effect sizes. AVGs could yield equivalent health benefits to children/adolescents as laboratory-based exercise or field-based physical activity. Therefore, AVGs can be a good alternative for sedentary behaviour and addition to traditional physical activity and sports in children/adolescents. © 2015 World Obesity.

Sensitivity analysis of heliostat aiming strategies and receiver size on annual thermal production of a molten salt external receiver

NASA Astrophysics Data System (ADS)

Servert, Jorge; González, Ana; Gil, Javier; López, Diego; Funes, Jose Felix; Jurado, Alfonso

2017-06-01

Even though receiver size and aiming strategy are to be jointly analyzed to optimize the thermal energy that can be extracted from a solar tower receiver, customarily, they have been studied as separated problems. The main reason is the high-level of detail required to define aiming strategies, which are often simplified in annual simulation models. Aiming strategies are usually focused on obtaining a homogeneous heat flux on the central receiver, with the goal to minimize the maximum heat flux value that may lead to damaging it. Some recent studies have addressed the effect of different aiming strategies on different receiver types, but they have only focused on the optical efficiency. The receiver size is also an additional parameter that has to be considered: larger receiver sizes provide a larger aiming surface and a reduction on spillage losses, but require higher investment while penalizing the thermal performance of the receiver due to the greater external convection losses. The present paper presents a sensitivity analysis of both factors for a predefined solar field at a fixed location, using a central receiver and molten salts as HTF. The analysis includes the design point values and annual energy outputs comparing the effect on the optical performance (measured using a spillage factor) and thermal energy production.

deep-orange and carnation define distinct stages in late endosomal biogenesis in Drosophila melanogaster.

PubMed

Sriram, V; Krishnan, K S; Mayor, Satyajit

2003-05-12

Endosomal degradation is severely impaired in primary hemocytes from larvae of eye color mutants of Drosophila. Using high resolution imaging and immunofluorescence microscopy in these cells, products of eye color genes, deep-orange (dor) and carnation (car), are localized to large multivesicular Rab7-positive late endosomes containing Golgi-derived enzymes. These structures mature into small sized Dor-negative, Car-positive structures, which subsequently fuse to form tubular lysosomes. Defective endosomal degradation in mutant alleles of dor results from a failure of Golgi-derived vesicles to fuse with morphologically arrested Rab7-positive large sized endosomes, which are, however, normally acidified and mature with wild-type kinetics. This locates the site of Dor function to fusion of Golgi-derived vesicles with the large Rab7-positive endocytic compartments. In contrast, endosomal degradation is not considerably affected in car1 mutant; fusion of Golgi-derived vesicles and maturation of large sized endosomes is normal. However, removal of Dor from small sized Car-positive endosomes is slowed, and subsequent fusion with tubular lysosomes is abolished. Overexpression of Dor in car1 mutant aggravates this defect, implicating Car in the removal of Dor from endosomes. This suggests that, in addition to an independent role in fusion with tubular lysosomes, the Sec1p homologue, Car, regulates Dor function.

The morphological and chemical characteristics of striatal neurons immunoreactive for the alpha1-subunit of the GABA(A) receptor in the rat.

PubMed

Waldvogel, H J; Kubota, Y; Trevallyan, S C; Kawaguchi, Y; Fritschy, J M; Mohler, H; Faull, R L

1997-10-01

The distribution, morphology and chemical characteristics of neurons immunoreactive for the alpha1-subunit of the GABA(A) receptor in the striatum of the basal ganglia in the rat brain were investigated at the light, confocal and electron microscope levels using single, double and triple immunohistochemical labelling techniques. The results showed that alpha1-subunit immunoreactive neurons were sparsely distributed throughout the rat striatum. Double and triple labelling results showed that all the alpha1-subunit-immunoreactive neurons were positive for glutamate decarboxylase and immunoreactive for the beta2,3 and gamma2 subunits of the GABA(A) receptor. Three types of alpha1-subunit-immunoreactive neurons were identified in the striatum on the basis of cellular morphology and chemical characteristics. The most numerous alpha1-subunit-immunoreactive neurons were medium-sized, aspiny neurons with a widely branching dendritic tree. They were parvalbumin-negative and were located mainly in the dorsolateral regions of the striatum. Electron microscopy showed that these neurons had an indented nuclear membrane, typical of striatal interneurons, and were surrounded by small numbers of axon terminals which established alpha1-subunit-immunoreactive synaptic contacts with the soma and dendrites. These cells were classified as type 1 alpha1-subunit-immunoreactive neurons and comprised 75% of the total population of alpha1-subunit-immunoreactive neurons in the striatum. The remaining alpha1-subunit-immunoreactive neurons comprised of a heterogeneous population of large-sized neurons localized in the ventral and medial regions of the striatum. The most numerous large-sized cells were parvalbumin-negative, had two to three relatively short branching dendrites and were designated type 2 alpha1-subunit-immunoreactive neurons. Electron microscopy showed that the type 2 neurons were characterized by a highly convoluted nuclear membrane and were sparsely covered with small axon terminals. The type 2 neurons comprised 20% of the total population of alpha1-subunit-immunoreactive neurons. The remaining large-sized alpha1-immunoreactive cells were designated type 3 cells; they were positive for parvalbumin and were distinguished by long branching dendrites extending dorsally for 600-800 microm into the striatum. These neurons comprised 5% of the total population of alpha1-subunit-immunoreactive neurons and were surrounded by enkephalin-immunoreactive terminals. Electron microscopy showed that the alpha1-subunit type 3 neurons had an indented nuclear membrane and were densely covered with small axon terminals which established alpha1-subunit-immunoreactive symmetrical synaptic contacts with the soma and dendrites. These results provide a detailed characterization of the distribution, morphology and chemical characteristics of the alpha1-subunit-immunoreactive neurons in the rat striatum and suggest that the type 1 and type 2 neurons comprise of separate populations of striatal interneurons while the type 3 neurons may represent the large striatonigral projection neurons described by Bolam et al. [Bolam J. P., Somogyi P., Totterdell S. and Smith A. D. (1981) Neuroscience 6, 2141-2157.].

Characterization and differentiation of rock varnish types from different environments by microanalytical techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macholdt, D. S.; Jochum, K. P.; Pöhlker, C.

We investigated rock varnishes collected from several locations and environments worldwide by a wide range of microanalytical techniques. These techniques were selected to address the challenges posed by the chemical and structural complexity within the micrometer- to nanometer-sized structures in these geological materials. Femtosecond laser ablation-inductively coupled plasma-mass spectrometry (fs LA-ICP-MS), scanning transmission X-ray microscopy-near edge X-ray adsorption fine structure spectroscopy (STXM-NEXAFS) in combination with scanning electron microscopy (SEM) of focused ion beam (FIB) ultra-thin (100–200 nm) sections, conventional and polarization microscopy, as well as electron paramagnetic resonance (EPR) measurements were used to obtain information about these rock varnishes. Rockmore » varnishes from different environments, which cannot readily be distinguished based on their macroscopic appearance, differ significantly in their constituent elemental mass fractions, e.g., of Mn, Fe, Ni, Co, Ba, and Pb, and their rare earth element (REE) patterns. Structural characteristics such as the particle sizes of embedded dust grains, internal structures such as layers of Mn-, Fe-, and Ca -rich material, and structures such as cavities varied between varnishes from different environments and regions in the world. The EPR spectra were consistent with aged biogenic Mn oxides in all samples, but showed subtle differences between samples of different origin. Our observations allow us to separate rock varnishes into different types, with differences that might be indicators of distinct geneses. Five different types of rock varnish could be distinguished, Type I–V, of which only Type I might be used as potential paleoclimate archive. Each varnish type has specific characteristics in terms of their elemental composition, element distribution, and structures. The combination of element ratios (Mn/Ba, Al/Ni, Mn/REY, Mn/Ce, Mn/Pb, La N /Yb N , and Ce/Ce*), total REE contents, and structures can be used to separate the different types of rock varnish from each other.« less

Questing height of nymphs of the bush tick, Haemaphysalis longicornis, and its closely related species, H. mageshimaensis: correlation with body size of the host.

PubMed

Tsunoda, T; Tatsuzawa, S

2004-05-01

The questing height (i.e. ambush height) of ticks on a plant plays an important role in host selection. To test the hypothesis that the questing height of ticks in a locality had adapted to the body size of the host in that locality, we examined the questing height of nymphs of the ticks, Haemaphysalis longicornis and H. mageshimaensis, at 7 locations in Japan. Sika deer, Cervus nippon, is the primary host of these ticks and there is considerable geographical variation in the body size of sika deer. Multiple regression analysis revealed that the questing height in the field was influenced by the height of the plants and by the body size of deer at a location. However, the questing height of ticks at some locations may have been constrained by the height of the plants and might not be the same as their intrinsic questing height. When ticks were placed in vertical glass tubes in the laboratory, the questing height of ticks from a locality was correlated with the mean body size of deer at that locality. Therefore, the prominent cue determining the questing height of H. longicornis and H. mageshimaensis seems to be the body size of the host deer.

Effects of Sediment Patches on Sediment Transport Predictions in Steep Mountain Channels

NASA Astrophysics Data System (ADS)

Monsalve Sepulveda, A.; Yager, E.

2013-12-01

Bed surface patches occur in most gravel-bedded rivers and in steep streams can be divided between relatively immobile boulders and more mobile patches of cobbles and gravel. This spatial variability in grain size, roughness and sorting impact bed load transport by altering the relative local mobility of different grain sizes and creating complex local flow fields. Large boulders also bear a significant part of the total shear stress and we hypothesize that the remaining shear stress on a given mobile patch is a distribution of values that depend on the local topography, patch type and location relative to the large roughness elements and thalweg. Current sediment transport equations do not account for the variation in roughness, local flow and grain size distributions on and between patches and often use an area-weighted approach to obtain a representative grain size distribution and reach-averaged shear stress. Such equations also do not distinguish between active (patches where at least one grain size is in motion) and inactive patches or include the difference in mobility between patch classes as result of spatial shear stress distributions. To understand the effects of sediment patches on sediment transport in steep channels, we calculated the shear stress distributions over a range of patch classes in a 10% gradient step-pool stream. We surveyed the bed with a high density resolution (every 5 cm in horizontal and vertical directions over a 40 m long reach) using a total station and terrestrial LiDAR, mapped and classified patches by their grain size distributions, and measured water surface elevations and mean velocities for low to moderate flow events. Using these data we calibrated a quasi-three dimensional model (FaSTMECH) to obtain shear stress distributions over each patch for a range of flow discharges. We modified Parker's (1990) equations to use the calculated shear stress distribution, measured grain sizes, and a specific hiding function for each patch class, and then added the bedload fluxes for each patch to calculate the reach-averaged sediment transport rate. Sediment mobility in patches was highly dependent on the patch's class and location relative to the thalweg and large roughness elements. Compared to deterministic formulations, the use of distributions of shear stress improved predictions of bedload transport in steep mountain channels.

The effects of dispersal patterns on marine reserves: does the tail wag the dog?

PubMed

Lockwood, Dale R; Hastings, Alan; Botsford, Louis W

2002-05-01

The concept of marine reserves as a method of improving management of fisheries is gaining momentum. While the list of benefits from reserves is frequently promoted, precise formulations of theory to support reserve design are not fully developed. To determine the size of reserves and the distances between reserves an understanding of the requirements for persistence of local populations is required. Unfortunately, conditions for persistence are poorly characterized, as are the larval dispersal patterns on which persistence depends. With the current paucity of information regarding meroplanktonic larval transport processes, understanding the robustness of theoretical results to larval dispersal is of key importance. From this formulation a broad range of dispersal patterns are analyzed. Larval dispersal is represented by a probability distribution that defines the fraction of successful settlers from an arbitrary location, the origin of the distribution, to any other location along the coast. While the effects of specific dispersal patterns have been investigated for invasion processes, critical habitat size and persistence issues have generally been addressed with only one or two dispersal types. To that end, we formulate models based on integrodifference equations that are spatially continuous and temporally discrete. We consider a range of dispersal distributions from leptokurtic to platykurtic. The effect of different dispersal patterns is considered for a single isolated reserve of varying size receiving no external larvae, as well as multiple reserves with varying degrees of connectivity. While different patterns result in quantitative differences in persistence, qualitatively similar effects across all patterns are seen in both single- and multiple reserve models. Persistence in an isolated reserve requires a size that is approximately twice the mean dispersal distance and regardless of the dispersal pattern the population in a patch is not persistent if the reserve size is reduced to just the mean dispersal distance. With an idealized coastline structure consisting of an infinite line of equally spaced reserves separated by regions of coastline in which reproduction is nil, the relative settlement as a function of the fraction of coastline and size of reserve is qualitatively very similar over a broad range of dispersal patterns. The upper limit for the minimum fraction of coastline held in reserve is about 40%. As the fraction of coastline is reduced, the minimum size of reserve becomes no more than 1.25 times the mean dispersal distance.

Contour Digitizing and Tagging Software (CONTAGRID).

DTIC Science & Technology

1980-04-01

TYPE TO TYPE FROM # * DELETE TYPE #1 #, #1 #1 #, e JOYN TYPE #, # * REORDER TYPE #, #1 #1 TYPE = INDEX, NON, DEPRESSION, CUT, FILL, # NUMBER Figure B...ERRCOD.N’.0)C’ TO 8020 SIZE - IOR( IAN ;D(4ZOIFE,ISL(mJF(1),-7)), + lAND(4ZFEOO,ISL(BUr(1),9))) iF(SIZE.GT.390)GO TO 8030 LM- 0 DO 110 I-1,SIZE CALL

Saturation in Phosphene Size with Increasing Current Levels Delivered to Human Visual Cortex.

PubMed

Bosking, William H; Sun, Ping; Ozker, Muge; Pei, Xiaomei; Foster, Brett L; Beauchamp, Michael S; Yoshor, Daniel

2017-07-26

Electrically stimulating early visual cortex results in a visual percept known as a phosphene. Although phosphenes can be evoked by a wide range of electrode sizes and current amplitudes, they are invariably described as small. To better understand this observation, we electrically stimulated 93 electrodes implanted in the visual cortex of 13 human subjects who reported phosphene size while stimulation current was varied. Phosphene size increased as the stimulation current was initially raised above threshold, but then rapidly reached saturation. Phosphene size also depended on the location of the stimulated site, with size increasing with distance from the foveal representation. We developed a model relating phosphene size to the amount of activated cortex and its location within the retinotopic map. First, a sigmoidal curve was used to predict the amount of activated cortex at a given current. Second, the amount of active cortex was converted to degrees of visual angle by multiplying by the inverse cortical magnification factor for that retinotopic location. This simple model accurately predicted phosphene size for a broad range of stimulation currents and cortical locations. The unexpected saturation in phosphene sizes suggests that the functional architecture of cerebral cortex may impose fundamental restrictions on the spread of artificially evoked activity and this may be an important consideration in the design of cortical prosthetic devices. SIGNIFICANCE STATEMENT Understanding the neural basis for phosphenes, the visual percepts created by electrical stimulation of visual cortex, is fundamental to the development of a visual cortical prosthetic. Our experiments in human subjects implanted with electrodes over visual cortex show that it is the activity of a large population of cells spread out across several millimeters of tissue that supports the perception of a phosphene. In addition, we describe an important feature of the production of phosphenes by electrical stimulation: phosphene size saturates at a relatively low current level. This finding implies that, with current methods, visual prosthetics will have a limited dynamic range available to control the production of spatial forms and that more advanced stimulation methods may be required. Copyright © 2017 the authors 0270-6474/17/377188-10$15.00/0.

Methodological considerations for analyzing trabecular architecture: an example from the primate hand.

PubMed

Kivell, Tracy L; Skinner, Matthew M; Lazenby, Richard; Hublin, Jean-Jacques

2011-02-01

Micro-computed tomographic analyses of trabecular bone architecture have been used to clarify the link between positional behavior and skeletal anatomy in primates. However, there are methodological decisions associated with quantifying and comparing trabecular anatomy across taxa that vary greatly in body size and morphology that can affect characterizations of trabecular architecture, such as choice of the volume of interest (VOI) size and location. The potential effects of these decisions may be amplified in small, irregular-shaped bones of the hands and feet that have more complex external morphology and more heterogeneous trabecular structure compared to, for example, the spherical epiphysis of the femoral head. In this study we investigate the effects of changes in VOI size and location on standard trabecular parameters in two bones of the hand, the capitate and third metacarpal, in a diverse sample of nonhuman primates that vary greatly in morphology, body mass and positional behavior. Results demonstrate that changes in VOI location and, to a lesser extent, changes in VOI size had a dramatic affect on many trabecular parameters, especially trabecular connectivity and structure (rods vs. plates), degree of anisotropy, and the primary orientation of the trabeculae. Although previous research has shown that some trabecular parameters are susceptible to slight variations in methodology (e.g. VOI location, scan resolution), this study provides a quantification of these effects in hand bones of a diverse sample of primates. An a priori understanding of the inherent biases created by the choice of VOI size and particularly location is critical to robust trabecular analysis and functional interpretation, especially in small bones with complex arthroses. © 2010 The Authors. Journal of Anatomy © 2010 Anatomical Society of Great Britain and Ireland.

Impact of facial defect reconstruction on attractiveness and negative facial perception.

PubMed

Dey, Jacob K; Ishii, Masaru; Boahene, Kofi D O; Byrne, Patrick; Ishii, Lisa E

2015-06-01

Measure the impact of facial defect reconstruction on observer-graded attractiveness and negative facial perception. Prospective, randomized, controlled experiment. One hundred twenty casual observers viewed images of faces with defects of varying sizes and locations before and after reconstruction as well as normal comparison faces. Observers rated attractiveness, defect severity, and how disfiguring, bothersome, and important to repair they considered each face. Facial defects decreased attractiveness -2.26 (95% confidence interval [CI]: -2.45, -2.08) on a 10-point scale. Mixed effects linear regression showed this attractiveness penalty varied with defect size and location, with large and central defects generating the greatest penalty. Reconstructive surgery increased attractiveness 1.33 (95% CI: 1.18, 1.47), an improvement dependent upon size and location, restoring some defect categories to near normal ranges of attractiveness. Iterated principal factor analysis indicated the disfiguring, important to repair, bothersome, and severity variables were highly correlated and measured a common domain; thus, they were combined to create the disfigured, important to repair, bothersome, severity (DIBS) factor score, representing negative facial perception. The DIBS regression showed defect faces have a 1.5 standard deviation increase in negative perception (DIBS: 1.69, 95% CI: 1.61, 1.77) compared to normal faces, which decreased by a similar magnitude after surgery (DIBS: -1.44, 95% CI: -1.49, -1.38). These findings varied with defect size and location. Surgical reconstruction of facial defects increased attractiveness and decreased negative social facial perception, an impact that varied with defect size and location. These new social perception data add to the evidence base demonstrating the value of high-quality reconstructive surgery. NA. © 2015 The American Laryngological, Rhinological and Otological Society, Inc.

Uterine Artery Embolization in 101 Cases of Uterine Fibroids: Do Size, Location, and Number of Fibroids Affect Therapeutic Success and Complications?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Firouznia, Kavous, E-mail: k_firouznia@yahoo.com; Ghanaati, Hossein; Sanaati, Mina

The purpose of this study was to evaluate whether the size, location, or number of fibroids affects therapeutic efficacy or complications of uterine artery embolization (UAE). Patients with symptomatic uterine fibroids (n = 101) were treated by selective bilateral UAE using 500- to 710-{mu}m polyvinyl alcohol (PVA) particles. Baseline measures of clinical symptoms, sonography, and MRI taken before the procedure were compared to those taken 1, 3, 6, and 12 months later. Complications and outcomes were analyzed for associations with fibroid size, location, and number. Reductions in mean fibroid volume were similar in patients with single (66.6 {+-} 21.5%) andmore » multiple (67.4 {+-} 25.0%) fibroids (p-value = 0.83). Menstrual improvement occurred in patients with single (93.3%) and multiple (72.2%) fibroids (p = 0.18). Changes in submucosal and other fibroids were not significantly different between the two groups (p's > 0.56). Linear regression analysis between primary fibroid volume as independent variable and percentage reduction of fibroid volume after 1 year yielded an R{sup 2} of 0.083 and the model coefficient was not statistically significant (p = 0.072). Multivariate regression models revealed no statistically or clinically significant coefficients or odds ratios for three independent variables (primary fibroid size, total number, and fibroid location) and all outcome variables (percent reduction of uterus and fibroid volumes in 1 year, improvement of clinical symptoms [menstrual, bulk related, and urinary] in 1 year, and complications after UAE). In conclusion, neither the success rate nor the probability of complications was affected by the primary fibroid size, location, or total number of fibroids.« less

A clinicopathologic review of 138 cases of mucoceles in a pediatric population.

PubMed

Martins-Filho, Paulo Ricardo Saquete; Santos, Thiago de Santana; da Silva, Heitor Fontes; Piva, Marta Rabello; Andrade, Emanuel Sávio de Souza; da Silva, Luiz Carlos Ferreira

2011-09-01

To evaluate the clinicopathologic features of pediatric mucoceles diagnosed in two public institutions in Brazil during an 18-year period. Clinical data (age, sex, history of trauma, location, and size) of 138 cases of mucoceles in children 0 to 16 years of age were obtained from medical records. The lesions were classified as mucus extravasation phenomenon and mucus retention phenomenon, depending on the presence of epithelial lining in the microscopic analysis. Mucoceles made up 24.5% of the oral pediatric lesions diagnosed in the period of study. Age at diagnosis ranged from 0.4 to 16.0 years, with a mean age of 10.8 years. Of the total of mucoceles, 87 were observed in females and 51 in males. The lower lip was the most commonly affected site, and a history of trauma was related by 87% of the patients. Histologically, 96.4% of mucoceles were diagnosed as mucus extravasation phenomenon. Cases of mucus retention phenomenon were relatively more common in the floor of the mouth, since one in three lesions in this location belonged to this histologic type. Regarding lesions in the lower lip, only 2.65% were diagnosed as mucus retention phenomenon. Trauma is the main etiologic factor involved in the development of mucoceles in children. The mucus extravasation phenomenon is the most common histologic type in this age group. Although rare, the retention type seems to be more common in lesions on the floor of the mouth.

Single Cell Profiling using Ionic Liquid Matrix-Enhanced Secondary Ion Mass Spectrometry for Neuronal Cell Type Differentiation

PubMed Central

Do, Thanh D.; Comi, Troy J.; Dunham, Sage J. B.; Rubakhin, Stanislav S.; Sweedler, Jonathan V.

2017-01-01

A high-throughput single cell profiling method has been developed for matrix-enhanced secondary ion mass spectrometry (ME-SIMS) to investigate the lipid profiles of neuronal cells. Populations of cells are dispersed onto the substrate, their locations determined using optical microscopy, and the cell locations used to guide the acquisition of SIMS spectra from the cells. Up to 2,000 cells can be assayed in one experiment at a rate of 6 s per cell. Multiple saturated and unsaturated phosphatidylcholines (PCs) and their fragments are detected and verified with tandem mass spectrometry from individual cells when ionic liquids are employed as a matrix. Optically guided single cell profiling with ME-SIMS is suitable for a range of cell sizes, from Aplysia californica neurons larger than 75 μm to 7-μm rat cerebellar neurons. ME-SIMS analysis followed by t-distributed stochastic neighbor embedding of peaks in the lipid molecular mass range (m/z 700–850) distinguishes several cell types from the rat central nervous system, largely based on the relative proportions of the four dominant lipids, PC(32:0), PC(34:1), PC(36:1), and PC(38:5). Furthermore, subpopulations within each cell type are tentatively classified consistent with their endogenous lipid ratios. The results illustrate the efficacy of a new approach to classify single cell populations and subpopulations using SIMS profiling of lipid and metabolite contents. These methods are broadly applicable for high throughput single cell chemical analyses. PMID:28194949

Search for the 700,000-year-old source crater of the Australasian tektite strewn field

NASA Technical Reports Server (NTRS)

Schnetzler, C. C.; Garvin, J. B.

1992-01-01

Many tektite investigations have hypothesized that the impact crater that was the source of the extensive Australasian strewn field lies somewhere in or near Indochina. This is due to variations in abundance and size of tektites across the strewn field, variation of thickness of microtektite layers in ocean cores, nature and ablation characteristics across the field, and, above all, the occurrence of the large, blocky, layered Muong Nong-type tektites in Indochina. A recent study of the location and chemistry of Muong Nong-type and splash-form tektites suggests that the source region can be further narrowed to a limited area in eastern Thailand and southern Loas. Satellite multispectral imagery, a digital elevation dataset, and maps showing drainage patterns were used to search within this area for possible anomalous features that may be large degraded impact craters. Four interesting structures were identified from these datasets, and they are presented.

Effects of spatial grouping on the functional response of predators

USGS Publications Warehouse

Cosner, C.; DeAngelis, D.L.; Ault, J.S.; Olson, D.B.

1999-01-01

A unified mechanistic approach is given for the derivation of various forms of functional response in predator-prey models. The derivation is based on the principle-of-mass action but with the crucial refinement that the nature of the spatial distribution of predators and/or opportunities for predation are taken into account in an implicit way. If the predators are assumed to have a homogeneous spatial distribution, then the derived functional response is prey-dependent. If the predators are assumed to form a dense colony or school in a single (possibly moving) location, or if the region where predators can encounter prey is assumed to be of limited size, then the functional response depends on both predator and prey densities in a manner that reflects feeding interference between predators. Depending on the specific assumptions, the resulting functional response may be of Beddington-DeAngelis type, of Hassell-Varley type, or ratio-dependent.

Risk factors associated with leptospirosis in dairy goats under tropical conditions in Brazil.

PubMed

Lilenbaum, Walter; Varges, Renato; Medeiros, Luciana; Cordeiro, Ana Gabriela; Cavalcanti, Amanda; Souza, Guilherme N; Richtzenhain, Leonardo; Vasconcellos, Silvio A

2008-02-01

Serum samples from 248 adult dairy goats from 13 flocks with lowered fertility farmed in the Rio de Janeiro region of Brazil were examined for Leptospira antibodies by MAT with 24 serovars, cut off 100. A questionnaire was completed for each herd. Antibodies were detected in 20.8% of these goats, mainly to serovar Hardjo. Risk factors associated with seroprevalence to leptospirosis were the frequency of professional veterinary supervision (OR = 2.35), climate (OR = 2.63) and grazing for more than 2h a day. Flock factors as size, type of milking and offering of food supplementation, as well as the location and topography, the type of animal housing or the presence of silos did not significantly affect seroprevalence. We suggest that a successful control program for goat leptospirosis should include a complete investigation of herd management practices, which could influence in the occurrence of the infection.

Structural Group-based Auditing of Missing Hierarchical Relationships in UMLS

PubMed Central

Chen, Yan; Gu, Huanying(Helen); Perl, Yehoshua; Geller, James

2009-01-01

The Metathesaurus of the UMLS was created by integrating various source terminologies. The inter-concept relationships were either integrated into the UMLS from the source terminologies or specially generated. Due to the extensive size and inherent complexity of the Metathesaurus, the accidental omission of some hierarchical relationships was inevitable. We present a recursive procedure which allows a human expert, with the support of an algorithm, to locate missing hierarchical relationships. The procedure starts with a group of concepts with exactly the same (correct) semantic type assignments. It then partitions the concepts, based on child-of hierarchical relationships, into smaller, singly rooted, hierarchically connected subgroups. The auditor only needs to focus on the subgroups with very few concepts and their concepts with semantic type reassignments. The procedure was evaluated by comparing it with a comprehensive manual audit and it exhibits a perfect error recall. PMID:18824248

Trichothecene resistance in wheat: Development of molecular markers for PDR-type ABC transporter genes.

PubMed

Mitterbauer, R; Heinrich, M; Rauscher, R; Lemmens, M; Bürstmayr, H; Adam, G

2003-03-01

Infection withFusarium graminearum andF. culmorum not only causes severe yield and quality losses, the most relevant concern is the contamination of cereal foods and feeds with trichothecenes (e.g. deoxynivalenol, DON). The ability to synthesize trichothecenes has been shown to be a virulence factor ofF. graminearum on wheat and, on the other hand, toxin resistance is most likely an important component of field resistance. Our hypothesis is that pleiotropic drug resistance mediated by PDR-type ABC transporter proteins (acting as membrane located drug efflux pumps) is a relevant mechanism of DON resistance not only in yeast but also in wheat. Goal of this project is the development of molecular markers for this gene family for use in marker-assisted plant breeding programs. The technical difficulties caused by the large size of the PDR-family are discussed.

A Study on the Thermomechanical Reliability Risks of Through-Silicon-Vias in Sensor Applications

PubMed Central

Shao, Shuai; Liu, Dapeng; Niu, Yuling; O’Donnell, Kathy; Sengupta, Dipak; Park, Seungbae

2017-01-01

Reliability risks for two different types of through-silicon-vias (TSVs) are discussed in this paper. The first is a partially-filled copper TSV, if which the copper layer covers the side walls and bottom. A polymer is used to fill the rest of the cavity. Stresses in risk sites are studied and ranked for this TSV structure by FEA modeling. Parametric studies for material properties (modulus and thermal expansion) of TSV polymer are performed. The second type is a high aspect ratio TSV filled by polycrystalline silicon (poly Si). Potential risks of the voids in the poly Si due to filling defects are studied. Fracture mechanics methods are utilized to evaluate the risk for two different assembly conditions: package assembled to printed circuit board (PCB) and package assembled to flexible substrate. The effect of board/substrate/die thickness and the size and location of the void are discussed. PMID:28208758

A Simulation Based Approach to Optimize Berth Throughput Under Uncertainty at Marine Container Terminals

NASA Technical Reports Server (NTRS)

Golias, Mihalis M.

2011-01-01

Berth scheduling is a critical function at marine container terminals and determining the best berth schedule depends on several factors including the type and function of the port, size of the port, location, nearby competition, and type of contractual agreement between the terminal and the carriers. In this paper we formulate the berth scheduling problem as a bi-objective mixed-integer problem with the objective to maximize customer satisfaction and reliability of the berth schedule under the assumption that vessel handling times are stochastic parameters following a discrete and known probability distribution. A combination of an exact algorithm, a Genetic Algorithms based heuristic and a simulation post-Pareto analysis is proposed as the solution approach to the resulting problem. Based on a number of experiments it is concluded that the proposed berth scheduling policy outperforms the berth scheduling policy where reliability is not considered.

Methods and means used in programming intelligent searches of technical documents

NASA Technical Reports Server (NTRS)

Gross, David L.

1993-01-01

In order to meet the data research requirements of the Safety, Reliability & Quality Assurance activities at Kennedy Space Center (KSC), a new computer search method for technical data documents was developed. By their very nature, technical documents are partially encrypted because of the author's use of acronyms, abbreviations, and shortcut notations. This problem of computerized searching is compounded at KSC by the volume of documentation that is produced during normal Space Shuttle operations. The Centralized Document Database (CDD) is designed to solve this problem. It provides a common interface to an unlimited number of files of various sizes, with the capability to perform any diversified types and levels of data searches. The heart of the CDD is the nature and capability of its search algorithms. The most complex form of search that the program uses is with the use of a domain-specific database of acronyms, abbreviations, synonyms, and word frequency tables. This database, along with basic sentence parsing, is used to convert a request for information into a relational network. This network is used as a filter on the original document file to determine the most likely locations for the data requested. This type of search will locate information that traditional techniques, (i.e., Boolean structured key-word searching), would not find.

SCC analysis of Alloy 600 tubes from a retired steam generator

NASA Astrophysics Data System (ADS)

Hwang, Seong Sik; Kim, Hong Pyo

2013-09-01

Steam generators (SG) equipped with Alloy 600 tubes of a Korean nuclear power plants were replaced with a new one having Alloy 690 tubes in 1998 after 20 years of operation. To set up a guide line for an examination of the other SG tubes, a metallographic examination of the defected tubes was carried out. A destructive analysis on 71 tubes was addressed, and a relation among the stress corrosion crack (SCC) defect location, defect depth, and location of the sludge pile was obtained. Tubes extracted from the retired SG were transferred to a hot laboratory. Detailed nondestructive analysis examinations were taken again at the laboratory, and the tubes were then destructively examined. The types and sizes of the cracks were characterized. The location and depth of the SCC were evaluated in terms of the location and height of the sludge. Most axial cracks were in the sludge pile, whereas the circumferential ones were around the top of the tube sheet (TTS) or below the TTS. Average defect depth of the axial cracks was deeper than that of the circumferential ones. Axial cracks at tube support plate (TSP) seem to be related with corrosion/sludge in crevice like at the TTS region. Circumferential cracks at TSP seem to be caused by tube denting at the upper part of the TSP. Tubes not having clear ECT signals for quantifying an ECT data-base. Tubes having no ECT signal. Tubes with a large ECT signal. Tubes with various types and sizes of flaws (primary water stress corrosion cracking (PWSCC), outside diameter stress corrosion cracking (ODSCC), Pit). Tubes with distinct PWSCC or ODSCC. Tubes were extracted from the RSG based on the field ECT with the criteria, and transferred to a hot laboratory at the Korea Atomic Energy Research Institute (KAERI) for destructive examination. A comprehensive ECT inspection was performed again at the hot laboratory to confirm the location of the cracks obtained from a field inspection. These exact locations of the defects were marked on the tube specimens for subsequent destructive examinations.Metallography on a tube section was examined by standard metallographic techniques. The mounted specimens were ground and polished. For a chemical activation of the polished surface, the samples were soaked in hydrochloric acid for 20 s then followed by cleaning in methanol. Chemical etching in a bromine etchant (98% Methanol + 2% Bromine) was applied for 3 to 4 s in an ultrasound cleaner.Destructive examinations were carried out using the procedures in accordance with the Electric Power Research Institute (EPRI) tube examination guidelines [2]. The types of defects were characterized and their sizes were measured using a high magnification contact camera and a scanning electron microscope (SEM). The surface deposit compositions on the outer diameter of the tubes were also analyzed using energy dispersive X-ray spectroscopy (EDS). The relation among the SCC defect location, defect depth, and sludge height was explored. Denting, pitting, PWSCC and ODSCC were observed on the RSG tubes as time went on. The analyzed Alloy 600 tube showed a typical LTMA microstructure, and the severe SCC of the RSG was attributed to the microstructure and slightly alkaline crevice environment in some respects. Most axial cracks were observed inside the sludge pile up region, which suggests that sludge may have a role in accelerating the growth of the axial cracks. No correlation was seen in the circumferential cracks and sludge pile, and dents in the tube sheet and phosphate chemistry might cause OD circumferential cracks at the TTS region. The average depth of the axial cracks was higher than that of the circumferential cracks. Axial ID cracks 4 mm long or over at the TTS showed 90%-100% tube wall penetration. On the contrary, the length of the axial OD cracks was not closely related with the depth OD axial cracks around the TSP appeared to be much shallower than those of the TTS region. This implies that the same length of TSP region cracks may have higher structural safety than that of cracks of the TTS region.

Estuarine bed-sediment-quality data collected in New Jersey and New York after Hurricane Sandy, 2013

USGS Publications Warehouse

Fischer, Jeffrey M.; Phillips, Patrick J.; Reilly, Timothy J.; Focazio, Michael J.; Loftin, Keith A.; Benzel, William M.; Jones, Daniel K.; Smalling, Kelly L.; Fisher, Shawn C.; Fisher, Irene J.; Iwanowicz, Luke R.; Romanok, Kristin M.; Jenkins, Darkus E.; Bowers, Luke; Boehlke, Adam; Foreman, William T.; Deetz, Anna C.; Carper, Lisa G.; Imbrigiotta, Thomas E.; Birdwell, Justin E.

2015-01-01

Bed-sediment samples were collected from June to October 2013 from 167 estuarine sites extending from Cape May, New Jersey, to the New York Harbor and the eastern end of Long Island. Each sampling location and study region was characterized by using geographic information to identify potential contaminant sources. Characterizations included land cover, locations and types of businesses (industrial, financial, and others), spills (sewage, chemical, and others), bulk storage facilities, effluent discharges within 2 kilometers of the sampling point, and discharges within inundated and non-inundated regions near the sampling location. Samples were analyzed for particle size, total organic carbon, metals and trace elements, semivolatile organic compounds, wastewater compounds, hormones, and sediment toxicity. Samples were also screened using x-ray fluorescence, Fourier transform infrared spectroscopy, and x-ray diffraction. In addition, bioassays for endocrine disruptors and protein phosphatase 2A inhibition were conducted. The study was designed to provide the data needed to understand the extent and sources of contamination resulting from Hurricane Sandy, to compare the chemistry and toxicity of estuarine bed sediments before and after the storm, and to evaluate the usefulness of rapid screening and bioassay approaches in disaster settings.

An approach for automated analysis of particle holograms

NASA Technical Reports Server (NTRS)

Stanton, A. C.; Caulfield, H. J.; Stewart, G. W.

1984-01-01

A simple method for analyzing droplet holograms is proposed that is readily adaptable to automation using modern image digitizers and analyzers for determination of the number, location, and size distributions of spherical or nearly spherical droplets. The method determines these parameters by finding the spatial location of best focus of the droplet images. With this location known, the particle size may be determined by direct measurement of image area in the focal plane. Particle velocity and trajectory may be determined by comparison of image locations at different instants in time. The method is tested by analyzing digitized images from a reconstructed in-line hologram, and the results show that the method is more accurate than a time-consuming plane-by-plane search for sharpest focus.

Optimizing Sampling Efficiency for Biomass Estimation Across NEON Domains

NASA Astrophysics Data System (ADS)

Abercrombie, H. H.; Meier, C. L.; Spencer, J. J.

2013-12-01

Over the course of 30 years, the National Ecological Observatory Network (NEON) will measure plant biomass and productivity across the U.S. to enable an understanding of terrestrial carbon cycle responses to ecosystem change drivers. Over the next several years, prior to operational sampling at a site, NEON will complete construction and characterization phases during which a limited amount of sampling will be done at each site to inform sampling designs, and guide standardization of data collection across all sites. Sampling biomass in 60+ sites distributed among 20 different eco-climatic domains poses major logistical and budgetary challenges. Traditional biomass sampling methods such as clip harvesting and direct measurements of Leaf Area Index (LAI) involve collecting and processing plant samples, and are time and labor intensive. Possible alternatives include using indirect sampling methods for estimating LAI such as digital hemispherical photography (DHP) or using a LI-COR 2200 Plant Canopy Analyzer. These LAI estimations can then be used as a proxy for biomass. The biomass estimates calculated can then inform the clip harvest sampling design during NEON operations, optimizing both sample size and number so that standardized uncertainty limits can be achieved with a minimum amount of sampling effort. In 2011, LAI and clip harvest data were collected from co-located sampling points at the Central Plains Experimental Range located in northern Colorado, a short grass steppe ecosystem that is the NEON Domain 10 core site. LAI was measured with a LI-COR 2200 Plant Canopy Analyzer. The layout of the sampling design included four, 300 meter transects, with clip harvests plots spaced every 50m, and LAI sub-transects spaced every 10m. LAI was measured at four points along 6m sub-transects running perpendicular to the 300m transect. Clip harvest plots were co-located 4m from corresponding LAI transects, and had dimensions of 0.1m by 2m. We conducted regression analyses with LAI and clip harvest data to determine whether LAI can be used as a suitable proxy for aboveground standing biomass. We also compared optimal sample sizes derived from LAI data, and clip-harvest data from two different size clip harvest areas (0.1m by 1m vs. 0.1m by 2m). Sample sizes were calculated in order to estimate the mean to within a standardized level of uncertainty that will be used to guide sampling effort across all vegetation types (i.e. estimated within × 10% with 95% confidence). Finally, we employed a Semivariogram approach to determine optimal sample size and spacing.

Size and shape in Melipona quadrifasciata anthidioides Lepeletier, 1836 (Hymenoptera; Meliponini).

PubMed

Nunes, L A; Passos, G B; Carvalho, C A L; Araújo, E D

2013-11-01

This study aimed to identify differences in wing shape among populations of Melipona quadrifasciata anthidioides obtained in 23 locations in the semi-arid region of Bahia state (Brazil). Analysis of the Procrustes distances among mean wing shapes indicated that population structure did not determine shape variation. Instead, populations were structured geographically according to wing size. The Partial Mantel Test between morphometric (shape and size) distance matrices and altitude, taking geographic distances into account, was used for a more detailed understanding of size and shape determinants. A partial Mantel test between morphometris (shape and size) variation and altitude, taking geographic distances into account, revealed that size (but not shape) is largely influenced by altitude (r = 0.54 p < 0.01). These results indicate greater evolutionary constraints for the shape variation, which must be directly associated with aerodynamic issues in this structure. The size, however, indicates that the bees tend to have larger wings in populations located at higher altitudes.

Opportunistic Wireless Charging System Design for an On-Demand Shuttle Service

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meintz, Andrew; Doubleday, Kate; Markel, Tony

System right-sizing is critical to the implementation of in-motion wireless power transfer (WPT) for electric vehicles. This study evaluates potential system designs for an on-demand employee shuttle by determining the required battery size based on the rated power at a variable number of charging locations. Vehicle power and state of charge are simulated over the drive cycle, based on position and velocity data at every second from the existing shuttle. Adding just one WPT location can halve the battery size. Many configurations are capable of self-sustaining with WPT, while others benefit from supplemental stationary charging.