Morphology of a Wetland Stream

PubMed

Jurmu; Andrle

1997-11-01

/ Little attention has been paid to wetland stream morphology in the geomorphological and environmental literature, and in the recently expanding wetland reconstruction field, stream design has been based primarily on stream morphologies typical of nonwetland alluvial environments. Field investigation of a wetland reach of Roaring Brook, Stafford, Connecticut, USA, revealed several significant differences between the morphology of this stream and the typical morphology of nonwetland alluvial streams. Six morphological features of the study reach were examined: bankfull flow, meanders, pools and riffles, thalweg location, straight reaches, and cross-sectional shape. It was found that bankfull flow definitions originating from streams in nonwetland environments did not apply. Unusual features observed in the wetland reach include tight bends and a large axial wavelength to width ratio. A lengthy straight reach exists that exceeds what is typically found in nonwetland alluvial streams. The lack of convex bank point bars in the bends, a greater channel width at riffle locations, an unusual thalweg location, and small form ratios (a deep and narrow channel) were also differences identified. Further study is needed on wetland streams of various regions to determine if differences in morphology between alluvial and wetland environments can be applied in order to improve future designs of wetland channels.KEY WORDS: Stream morphology; Wetland restoration; Wetland creation; Bankfull; Pools and riffles; Meanders; Thalweg

Nuclear Power Plants. Revised.

ERIC Educational Resources Information Center

Lyerly, Ray L.; Mitchell, Walter, III

This publication is one of a series of information booklets for the general public published by the United States Atomic Energy Commission. Among the topics discussed are: Why Use Nuclear Power?; From Atoms to Electricity; Reactor Types; Typical Plant Design Features; The Cost of Nuclear Power; Plants in the United States; Developments in Foreign…

Concurrent design of quasi-random photonic nanostructures

PubMed Central

Lee, Won-Kyu; Yu, Shuangcheng; Engel, Clifford J.; Reese, Thaddeus; Rhee, Dongjoon; Chen, Wei

2017-01-01

Nanostructured surfaces with quasi-random geometries can manipulate light over broadband wavelengths and wide ranges of angles. Optimization and realization of stochastic patterns have typically relied on serial, direct-write fabrication methods combined with real-space design. However, this approach is not suitable for customizable features or scalable nanomanufacturing. Moreover, trial-and-error processing cannot guarantee fabrication feasibility because processing–structure relations are not included in conventional designs. Here, we report wrinkle lithography integrated with concurrent design to produce quasi-random nanostructures in amorphous silicon at wafer scales that achieved over 160% light absorption enhancement from 800 to 1,200 nm. The quasi-periodicity of patterns, materials filling ratio, and feature depths could be independently controlled. We statistically represented the quasi-random patterns by Fourier spectral density functions (SDFs) that could bridge the processing–structure and structure–performance relations. Iterative search of the optimal structure via the SDF representation enabled concurrent design of nanostructures and processing. PMID:28760975

Towards the Improved Discovery and Design of Functional Peptides: Common Features of Diverse Classes Permit Generalized Prediction of Bioactivity

PubMed Central

Mooney, Catherine; Haslam, Niall J.; Pollastri, Gianluca; Shields, Denis C.

2012-01-01

The conventional wisdom is that certain classes of bioactive peptides have specific structural features that endow their particular functions. Accordingly, predictions of bioactivity have focused on particular subgroups, such as antimicrobial peptides. We hypothesized that bioactive peptides may share more general features, and assessed this by contrasting the predictive power of existing antimicrobial predictors as well as a novel general predictor, PeptideRanker, across different classes of peptides. We observed that existing antimicrobial predictors had reasonable predictive power to identify peptides of certain other classes i.e. toxin and venom peptides. We trained two general predictors of peptide bioactivity, one focused on short peptides (4–20 amino acids) and one focused on long peptides ( amino acids). These general predictors had performance that was typically as good as, or better than, that of specific predictors. We noted some striking differences in the features of short peptide and long peptide predictions, in particular, high scoring short peptides favour phenylalanine. This is consistent with the hypothesis that short and long peptides have different functional constraints, perhaps reflecting the difficulty for typical short peptides in supporting independent tertiary structure. We conclude that there are general shared features of bioactive peptides across different functional classes, indicating that computational prediction may accelerate the discovery of novel bioactive peptides and aid in the improved design of existing peptides, across many functional classes. An implementation of the predictive method, PeptideRanker, may be used to identify among a set of peptides those that may be more likely to be bioactive. PMID:23056189

School Connectedness: Strategies for Increasing Protective Factors among Youth

ERIC Educational Resources Information Center

Centers for Disease Control and Prevention, 2009

2009-01-01

Efforts to improve child and adolescent health typically have featured interventions designed to address specific health risk behaviors, such as tobacco use, alcohol and drug use, violence, gang involvement, and early sexual initiation. However, results from a growing number of studies suggest that greater health impact might be achieved by also…

CPU SIM: A Computer Simulator for Use in an Introductory Computer Organization-Architecture Class.

ERIC Educational Resources Information Center

Skrein, Dale

1994-01-01

CPU SIM, an interactive low-level computer simulation package that runs on the Macintosh computer, is described. The program is designed for instructional use in the first or second year of undergraduate computer science, to teach various features of typical computer organization through hands-on exercises. (MSE)

Whirl Flutter Studies for a SSTOL Transport Demonstrator

NASA Technical Reports Server (NTRS)

Acree, C. W., Jr.; Hoffman, Krishna

2004-01-01

A proposed new class of aircraft - the Advanced Theater Transport (ATT) will combine strategic range and high payload with 'Super-STOL' (short take-off and landing) capability. It is also proposed to modify a YC-15 into a technology demonstrator with a 20-deg tilt wing; four, eight-bladed propellers; cross-shafted gearboxes and V-22 engines. These constitute a unique combination of design features that potentially affect performance, loads and whirl-mode stability (whirl flutter). NASA Ames Research Center is working with Boeing and Hamilton Sundstrand on technology challenges presented by the concept; the purpose of NASA involvement is to establish requirements for the demonstrator and for early design guidance, with emphasis on whirl flutter. CAMRAD II is being used to study the effects of various design features on whirl flutter, with special attention to areas where such features differ from existing aircraft, notably tiltrotors. Although the stability margins appear to be more than adequate, the concept requires significantly different analytical methods, principally including far more blade modes, than typically used for tiltrotors.

Analytical fuel property effects: Small combustors, phase 2

NASA Technical Reports Server (NTRS)

Hill, T. G.; Monty, J. D.; Morton, H. L.

1985-01-01

The effects of non-standard aviation fuels on a typical small gas turbine combustor were studied and the effectiveness of design changes intended to counter the effects of these fuels was evaluated. The T700/CT7 turboprop engine family was chosen as being representative of the class of aircraft power plants desired for this study. Fuel properties, as specified by NASA, are characterized by low hydrogen content and high aromatics levels. No. 2 diesel fuel was also evaluated in this program. Results demonstrated the anticipated higher than normal smoke output and flame radiation intensity with resulting increased metal temperatures on the baseline T700 combustor. Three new designs were evaluated using the non standard fuels. The three designs incorporated enhanced cooling features and smoke reduction features. All three designs, when burning the broad specification fuels, exhibited metal temperatures at or below the baseline combustor temperatures on JP-5. Smoke levels were acceptable but higher than predicted.

Evaluation of two polyimides and of an improved liner retention design for self-lubricating bushings

NASA Technical Reports Server (NTRS)

Sliney, H. E.

1984-01-01

Two different polyimide polymers were studied and the effectiveness of a design feature to improve retention of the self lubricating composite liners under high load was evaluated. The basic bearing design consisted of a molded layer of chopped graphite-fiber-reinforced-polyimide (GFRP) composite bonded to the bore of a steel bushing. The friction, wear, and load carrying ability of the bushings were determined in oscillating tests at 25, 260 and 315 C at radial unit loads up to 260 MPa. Friction coefficients were typically 0.15 to 0.25. Bushings with liners containing a new partially fluorinated polymer were functional, but had a lower load capacity and higher wear rate than those containing a more conventional, high temperature polyimide. The liner retention design feature reduced the tendency of the liners to crack and work out of the contact zone under high oscillating loads.

The role of semantic complexity in treatment of naming deficits: training semantic categories in fluent aphasia by controlling exemplar typicality.

PubMed

Kiran, Swathi; Thompson, Cynthia K

2003-06-01

The effect of typicality of category exemplars on naming was investigated using a single subject experimental design across participants and behaviors in 4 patients with fluent aphasia. Participants received a semantic feature treatment to improve naming of either typical or atypical items within semantic categories, while generalization was tested to untrained items of the category. The order of typicality and category trained was counterbalanced across participants. Results indicated that patients trained on naming of atypical exemplars demonstrated generalization to naming of intermediate and typical items. However, patients trained on typical items demonstrated no generalized naming effect to intermediate or atypical examples. Furthermore, analysis of errors indicated an evolution of errors throughout training, from those with no apparent relationship to the target to primarily semantic and phonemic paraphasias. Performance on standardized language tests also showed changes as a function of treatment. Theoretical and clinical implications regarding the impact of considering semantic complexity on rehabilitation of naming deficits in aphasia are discussed.

The role of semantic complexity in treatment of naming deficits: training semantic categories in fluent aphasia by controlling exemplar typicality.

PubMed

Kiran, Swathi; Thompson, Cynthia K

2003-08-01

The effect of typicality of category exemplars on naming was investigated using a single subject experimental design across participants and behaviors in 4 patients with fluent aphasia. Participants received a semantic feature treatment to improve naming of either typical or atypical items within semantic categories, while generalization was tested to untrained items of the category. The order of typicality and category trained was counterbalanced across participants. Results indicated that patients trained on naming of atypical exemplars demonstrated generalization to naming of intermediate and typical items. However, patients trained on typical items demonstrated no generalized naming effect to intermediate or atypical examples. Furthermore, analysis of errors indicated an evolution of errors throughout training, from those with no apparent relationship to the target to primarily semantic and phonemic paraphasias. Performance on standardized language tests also showed changes as a function of treatment. Theoretical and clinical implications regarding the impact of considering semantic complexity on rehabilitation of naming deficits in aphasia are discussed.

Recasting a Traditional Laboratory Practical as a "Design-Your-Own Protocol" to Teach a Universal Research Skill

ERIC Educational Resources Information Center

Whitworth, David E.

2016-01-01

Laboratory-based practical classes are a common feature of life science teaching, during which students learn how to perform experiments and generate/interpret data. Practical classes are typically instructional, concentrating on providing topic- and technique-specific skills, however to produce research-capable graduates it is also important to…

Broadband locally resonant metamaterials with graded hierarchical architecture

NASA Astrophysics Data System (ADS)

Liu, Chenchen; Reina, Celia

2018-03-01

We investigate the effect of hierarchical designs on the bandgap structure of periodic lattice systems with inner resonators. A detailed parameter study reveals various interesting features of structures with two levels of hierarchy as compared with one level systems with identical static mass. In particular: (i) their overall bandwidth is approximately equal, yet bounded above by the bandwidth of the single-resonator system; (ii) the number of bandgaps increases with the level of hierarchy; and (iii) the spectrum of bandgap frequencies is also enlarged. Taking advantage of these features, we propose graded hierarchical structures with ultra-broadband properties. These designs are validated over analogous continuum models via finite element simulations, demonstrating their capability to overcome the bandwidth narrowness that is typical of resonant metamaterials.

Designing human centered GeoVisualization application--the SanaViz--for telehealth users: a case study.

PubMed

Joshi, Ashish; de Araujo Novaes, Magdala; Machiavelli, Josiane; Iyengar, Sriram; Vogler, Robert; Johnson, Craig; Zhang, Jiajie; Hsu, Chiehwen E

2012-01-01

Public health data is typically organized by geospatial unit. GeoVisualization (GeoVis) allows users to see information visually on a map. Examine telehealth users' perceptions towards existing public health GeoVis applications and obtains users' feedback about features important for the design and development of Human Centered GeoVis application "the SanaViz". We employed a cross sectional study design using mixed methods approach for this pilot study. Twenty users involved with the NUTES telehealth center at Federal University of Pernambuco (UFPE), Recife, Brazil were enrolled. Open and closed ended questionnaires were used to gather data. We performed audio recording for the interviews. Information gathered included socio-demographics, prior spatial skills and perception towards use of GeoVis to evaluate telehealth services. Card sorting and sketching methods were employed. Univariate analysis was performed for the continuous and categorical variables. Qualitative analysis was performed for open ended questions. Existing Public Health GeoVis applications were difficult to use. Results found interaction features zooming, linking and brushing and representation features Google maps, tables and bar chart as most preferred GeoVis features. Early involvement of users is essential to identify features necessary to be part of the human centered GeoVis application "the SanaViz".

Risk Evaluation in the Pre-Phase A Conceptual Design of Spacecraft

NASA Technical Reports Server (NTRS)

Fabisinski, Leo L., III; Maples, Charlotte Dauphne

2010-01-01

Typically, the most important decisions in the design of a spacecraft are made in the earliest stages of its conceptual design the Pre-Phase A stages. It is in these stages that the greatest number of design alternatives is considered, and the greatest number of alternatives is rejected. The focus of Pre-Phase A conceptual development is on the evaluation and comparison of whole concepts and the larger-scale systems comprising those concepts. This comparison typically uses general Figures of Merit (FOMs) to quantify the comparative benefits of designs and alternative design features. Along with mass, performance, and cost, risk should be one of the major FOMs in evaluating design decisions during the conceptual design phases. However, risk is often given inadequate consideration in conceptual design practice. The reasons frequently given for this lack of attention to risk include: inadequate mission definition, lack of rigorous design requirements in early concept phases, lack of fidelity in risk assessment methods, and under-evaluation of risk as a viable FOM for design evaluation. In this paper, the role of risk evaluation in early conceptual design is discussed. The various requirements of a viable risk evaluation tool at the Pre-Phase A level are considered in light of the needs of a typical spacecraft design study. A technique for risk identification and evaluation is presented. The application of the risk identification and evaluation approach to the conceptual design process is discussed. Finally, a computational tool for risk profiling is presented and applied to assess the risk for an existing Pre-Phase A proposal. The resulting profile is compared to the risks identified for the proposal by other means.

Design feasibility of an advanced technology supersonic cruise aircraft

NASA Technical Reports Server (NTRS)

Rowe, W. T.

1976-01-01

Research and development programs provide confidence that technology is in-hand to design an economically attractive, environmentally sound supersonic cruise aircraft for commercial operations. The principal results of studies and tests are described including those which define the selection of significant design features. These typically include the results of: (1) wind-tunnel tests, both subsonic and supersonic, (2) propulsion performance and acoustic tests on noise suppressors, including forward-flight effects, (3) studies of engine/airframe integration, which lead to the selection of engine cycles/sizes to meet future market, economic, and social requirements; and (4) structural testing.

Supporting Knowledge Integration in Chemistry with a Visualization-Enhanced Inquiry Unit

NASA Astrophysics Data System (ADS)

Chiu, Jennifer L.; Linn, Marcia C.

2014-02-01

This paper describes the design and impact of an inquiry-oriented online curriculum that takes advantage of dynamic molecular visualizations to improve students' understanding of chemical reactions. The visualization-enhanced unit uses research-based guidelines following the knowledge integration framework to help students develop coherent understanding by connecting and refining existing and new ideas. The inquiry unit supports students to develop connections among molecular, observable, and symbolic representations of chemical reactions. Design-based research included a pilot study, a study comparing the visualization-enhanced inquiry unit to typical instruction, and a course-long comparison study featuring a delayed posttest. Students participating in the visualization-enhanced unit outperformed students receiving typical instruction and further consolidated their understanding on the delayed posttest. Students who used the visualization-enhanced unit formed more connections among concepts than students with typical textbook and lecture-based instruction. Item analysis revealed the types of connections students made when studying the curriculum and suggested how these connections enabled students to consolidate their understanding as they continued in the chemistry course. Results demonstrate that visualization-enhanced inquiry designed for knowledge integration can improve connections between observable and atomic-level phenomena and serve students well as they study subsequent topics in chemistry.

Fast mapping semantic features: performance of adults with normal language, history of disorders of spoken and written language, and attention deficit hyperactivity disorder on a word-learning task.

PubMed

Alt, Mary; Gutmann, Michelle L

2009-01-01

This study was designed to test the word learning abilities of adults with typical language abilities, those with a history of disorders of spoken or written language (hDSWL), and hDSWL plus attention deficit hyperactivity disorder (+ADHD). Sixty-eight adults were required to associate a novel object with a novel label, and then recognize semantic features of the object and phonological features of the label. Participants were tested for overt ability (accuracy) and covert processing (reaction time). The +ADHD group was less accurate at mapping semantic features and slower to respond to lexical labels than both other groups. Different factors correlated with word learning performance for each group. Adults with language and attention deficits are more impaired at word learning than adults with language deficits only. Despite behavioral profiles like typical peers, adults with hDSWL may use different processing strategies than their peers. Readers will be able to: (1) recognize the influence of a dual disability (hDSWL and ADHD) on word learning outcomes; (2) identify factors that may contribute to word learning in adults in terms of (a) the nature of the words to be learned and (b) the language processing of the learner.

Learning about the internal structure of categories through classification and feature inference.

PubMed

Jee, Benjamin D; Wiley, Jennifer

2014-01-01

Previous research on category learning has found that classification tasks produce representations that are skewed toward diagnostic feature dimensions, whereas feature inference tasks lead to richer representations of within-category structure. Yet, prior studies often measure category knowledge through tasks that involve identifying only the typical features of a category. This neglects an important aspect of a category's internal structure: how typical and atypical features are distributed within a category. The present experiments tested the hypothesis that inference learning results in richer knowledge of internal category structure than classification learning. We introduced several new measures to probe learners' representations of within-category structure. Experiment 1 found that participants in the inference condition learned and used a wider range of feature dimensions than classification learners. Classification learners, however, were more sensitive to the presence of atypical features within categories. Experiment 2 provided converging evidence that classification learners were more likely to incorporate atypical features into their representations. Inference learners were less likely to encode atypical category features, even in a "partial inference" condition that focused learners' attention on the feature dimensions relevant to classification. Overall, these results are contrary to the hypothesis that inference learning produces superior knowledge of within-category structure. Although inference learning promoted representations that included a broad range of category-typical features, classification learning promoted greater sensitivity to the distribution of typical and atypical features within categories.

Effects of temperature and mass conservation on the typical chemical sequences of hydrogen oxidation

NASA Astrophysics Data System (ADS)

Nicholson, Schuyler B.; Alaghemandi, Mohammad; Green, Jason R.

2018-01-01

Macroscopic properties of reacting mixtures are necessary to design synthetic strategies, determine yield, and improve the energy and atom efficiency of many chemical processes. The set of time-ordered sequences of chemical species are one representation of the evolution from reactants to products. However, only a fraction of the possible sequences is typical, having the majority of the joint probability and characterizing the succession of chemical nonequilibrium states. Here, we extend a variational measure of typicality and apply it to atomistic simulations of a model for hydrogen oxidation over a range of temperatures. We demonstrate an information-theoretic methodology to identify typical sequences under the constraints of mass conservation. Including these constraints leads to an improved ability to learn the chemical sequence mechanism from experimentally accessible data. From these typical sequences, we show that two quantities defining the variational typical set of sequences—the joint entropy rate and the topological entropy rate—increase linearly with temperature. These results suggest that, away from explosion limits, data over a narrow range of thermodynamic parameters could be sufficient to extrapolate these typical features of combustion chemistry to other conditions.

Novel and general approach to linear filter design for contrast-to-noise ratio enhancement of magnetic resonance images with multiple interfering features in the scene

NASA Astrophysics Data System (ADS)

Soltanian-Zadeh, Hamid; Windham, Joe P.

1992-04-01

Maximizing the minimum absolute contrast-to-noise ratios (CNRs) between a desired feature and multiple interfering processes, by linear combination of images in a magnetic resonance imaging (MRI) scene sequence, is attractive for MRI analysis and interpretation. A general formulation of the problem is presented, along with a novel solution utilizing the simple and numerically stable method of Gram-Schmidt orthogonalization. We derive explicit solutions for the case of two interfering features first, then for three interfering features, and, finally, using a typical example, for an arbitrary number of interfering feature. For the case of two interfering features, we also provide simplified analytical expressions for the signal-to-noise ratios (SNRs) and CNRs of the filtered images. The technique is demonstrated through its applications to simulated and acquired MRI scene sequences of a human brain with a cerebral infarction. For these applications, a 50 to 100% improvement for the smallest absolute CNR is obtained.

Impact evaluation of composite floor sections

NASA Technical Reports Server (NTRS)

Boitnott, Richard L.; Fasanella, Edwin L.

1989-01-01

Graphite-epoxy floor sections representative of aircraft fuselage construction were statically and dynamically tested to evaluate their response to crash loadings. These floor sections were fabricated using a frame-stringer design typical of present aluminum aircraft without features to enhance crashworthiness. The floor sections were tested as part of a systematic research program developed to study the impact response of composite components of increasing complexity. The ultimate goal of the research program is to develop crashworthy design features for future composite aircraft. Initially, individual frames of six-foot diameter were tested both statically and dynamically. The frames were then used to construct built-up floor sections for dynamic tests at impact velocities of approximately 20 feet/sec to simulate survivable crash velocities. In addition, static tests were conducted to gain a better understanding of the failure mechanisms seen in the dynamic tests.

Ontogeny of tick hemocytes: a comparative analysis of Ixodes ricinus and Ornithodoros moubata.

PubMed

Borovicková, Barbara; Hypsa, Václav

2005-01-01

Hemocytes of two tick species, Ixodes ricinus and Ornithodoros moubata, were investigated with the aim to determine their ultrastructural characteristics and developmental relationships. Only a limited number of ultrastructural features was shown to be unequivocally homological across all hemocyte types. The two species, representing distant groups of ticks, differ in the composition of their circular cell populations. In I. ricinus, three groups of distinct morphological types of hemocytes could be determined according to well-defined ultrastructural features: a typical non-phagocytic granular cell with electron-dense granula and homogeneous cytoplasm (Gr II), and two different types of phagocytic hemocytes, namely plasmatocytes with a low number of granula and phagocytic granolocytes, designated as Gr I. In contrast, an additional cell type resembling insect spherulocytes was determined in O. moubata. This cell type does not seem to be homologous to any I. ricinus hemocyte and may represent a cell type typical of soft ticks only. Possible ontogenetic lineages of the hemocytes of both tick-species were inferred.

Optimizing defect inspection strategy through the use of design-aware database control layers

NASA Astrophysics Data System (ADS)

Stoler, Dvori; Ruch, Wayne; Ma, Weimin; Chakravarty, Swapnajit; Liu, Steven; Morgan, Ray; Valadez, John; Moore, Bill; Burns, John

2007-10-01

Resolution limitations in the mask making process can cause differences between the features that appear in a database and those printed to a reticle. These differences may result from intentional or unintentional features in the database exceeding the resolution limit of the mask making process such as small gaps or lines in the data, line end shortening on small sub-resolution assist features etc creating challenges to both mask writing and mask inspection. Areas with high variance from design to mask, often referred to as high MEEF areas (mask error enhancement factor), become highly problematic and can directly impact mask and device yield, mask manufacturing cycle time and ultimately mask costs. Specific to mask inspection it may be desirable to inspect certain non-critical or non-relevant features at reduced sensitivity so as not to detect real, but less significant process defects. In contrast there may also be times where increased sensitivity is required for critical mask features or areas. Until recently, this process was extremely manual, creating added time and cost to the mask inspection cycle. Shifting to more intelligent and automated inspection flows is the key focus of this paper. A novel approach to importing design data directly into the mask inspection to include both MDP generated MRC errors files and LRC generated MEEF files. The results of recently developed inspection and review capability based upon controlling defect inspection using design aware data base control layers on a pixel basis are discussed. Typical mask shop applications and implementations will be shown.

Green Infrastructure Design Based on Spatial Conservation Prioritization and Modeling of Biodiversity Features and Ecosystem Services.

PubMed

Snäll, Tord; Lehtomäki, Joona; Arponen, Anni; Elith, Jane; Moilanen, Atte

2016-02-01

There is high-level political support for the use of green infrastructure (GI) across Europe, to maintain viable populations and to provide ecosystem services (ES). Even though GI is inherently a spatial concept, the modern tools for spatial planning have not been recognized, such as in the recent European Environment Agency (EEA) report. We outline a toolbox of methods useful for GI design that explicitly accounts for biodiversity and ES. Data on species occurrence, habitats, and environmental variables are increasingly available via open-access internet platforms. Such data can be synthesized by statistical species distribution modeling, producing maps of biodiversity features. These, together with maps of ES, can form the basis for GI design. We argue that spatial conservation prioritization (SCP) methods are effective tools for GI design, as the overall SCP goal is cost-effective allocation of conservation efforts. Corridors are currently promoted by the EEA as the means for implementing GI design, but they typically target the needs of only a subset of the regional species pool. SCP methods would help to ensure that GI provides a balanced solution for the requirements of many biodiversity features (e.g., species, habitat types) and ES simultaneously in a cost-effective manner. Such tools are necessary to make GI into an operational concept for combating biodiversity loss and promoting ES.

Green Infrastructure Design Based on Spatial Conservation Prioritization and Modeling of Biodiversity Features and Ecosystem Services

NASA Astrophysics Data System (ADS)

Snäll, Tord; Lehtomäki, Joona; Arponen, Anni; Elith, Jane; Moilanen, Atte

2016-02-01

There is high-level political support for the use of green infrastructure (GI) across Europe, to maintain viable populations and to provide ecosystem services (ES). Even though GI is inherently a spatial concept, the modern tools for spatial planning have not been recognized, such as in the recent European Environment Agency (EEA) report. We outline a toolbox of methods useful for GI design that explicitly accounts for biodiversity and ES. Data on species occurrence, habitats, and environmental variables are increasingly available via open-access internet platforms. Such data can be synthesized by statistical species distribution modeling, producing maps of biodiversity features. These, together with maps of ES, can form the basis for GI design. We argue that spatial conservation prioritization (SCP) methods are effective tools for GI design, as the overall SCP goal is cost-effective allocation of conservation efforts. Corridors are currently promoted by the EEA as the means for implementing GI design, but they typically target the needs of only a subset of the regional species pool. SCP methods would help to ensure that GI provides a balanced solution for the requirements of many biodiversity features (e.g., species, habitat types) and ES simultaneously in a cost-effective manner. Such tools are necessary to make GI into an operational concept for combating biodiversity loss and promoting ES.

National hydrography dataset--linear referencing

USGS Publications Warehouse

Simley, Jeffrey; Doumbouya, Ariel

2012-01-01

Geospatial data normally have a certain set of standard attributes, such as an identification number, the type of feature, and name of the feature. These standard attributes are typically embedded into the default attribute table, which is directly linked to the geospatial features. However, it is impractical to embed too much information because it can create a complex, inflexible, and hard to maintain geospatial dataset. Many scientists prefer to create a modular, or relational, data design where the information about the features is stored and maintained separately, then linked to the geospatial data. For example, information about the water chemistry of a lake can be maintained in a separate file and linked to the lake. A Geographic Information System (GIS) can then relate the water chemistry to the lake and analyze it as one piece of information. For example, the GIS can select all lakes more than 50 acres, with turbidity greater than 1.5 milligrams per liter.

Phenomenology of manic episodes according to the presence or absence of depressive features as defined in DSM-5: Results from the IMPACT self-reported online survey.

PubMed

Vieta, Eduard; Grunze, Heinz; Azorin, Jean-Michel; Fagiolini, Andrea

2014-03-01

The aim of this study was to describe the phenomenology of mania and depression in bipolar patients experiencing a manic episode with mixed features as defined in the new Diagnostic and Statistical Manual of Mental Disorders (DSM-5). In this multicenter, international on-line survey (the IMPACT study), 700 participants completed a 54-item questionnaire on demographics, diagnosis, symptomatology, communication of the disease, impact on life, and treatment received. Patients with a manic episode with or without DSM-5 criteria for mixed features were compared using descriptive and inferential statistics. Patients with more than 3 depressive symptoms were more likely to have had a delay in diagnosis, more likely to have experienced shorter symptom-free periods, and were characterized by a marked lower prevalence of typical manic manifestations. All questionnaire items exploring depressive symptomatology, including the DSM-5 criteria defining a manic episode as "with mixed features", were significantly overrepresented in the group of patients with depressive symptoms. Anxiety associated with irritability/agitation was also more frequent among patients with mixed features. Retrospective cross-sectional design, sensitive to recall bias. Two of the 6 DSM-5 required criteria for the specifier "with mixed features" were not explored: suicidality and psychomotor retardation. Bipolar disorder patients with at least 3 depressive symptoms during a manic episode self-reported typical symptomatology. Anxiety with irritability/agitation differentiated patients with depressive symptoms during mania from those with "pure" manic episodes. The results support the use of DSM-5 mixed features specifier and its value in research and clinical practice. Copyright © 2014 Elsevier B.V. All rights reserved.

A Co-modeling Method Based on Component Features for Mechatronic Devices in Aero-engines

NASA Astrophysics Data System (ADS)

Wang, Bin; Zhao, Haocen; Ye, Zhifeng

2017-08-01

Data-fused and user-friendly design of aero-engine accessories is required because of their structural complexity and stringent reliability. This paper gives an overview of a typical aero-engine control system and the development process of key mechatronic devices used. Several essential aspects of modeling and simulation in the process are investigated. Considering the limitations of a single theoretic model, feature-based co-modeling methodology is suggested to satisfy the design requirements and compensate for diversity of component sub-models for these devices. As an example, a stepper motor controlled Fuel Metering Unit (FMU) is modeled in view of the component physical features using two different software tools. An interface is suggested to integrate the single discipline models into the synthesized one. Performance simulation of this device using the co-model and parameter optimization for its key components are discussed. Comparison between delivery testing and the simulation shows that the co-model for the FMU has a high accuracy and the absolute superiority over a single model. Together with its compatible interface with the engine mathematical model, the feature-based co-modeling methodology is proven to be an effective technical measure in the development process of the device.

Energy conservation through optimum utilization of site energy sources for all season thermal comfort in new residential construction for single family attached (rowhouse/townhouse) designs

NASA Astrophysics Data System (ADS)

Gerber, S.; Holsman, J. P.

1981-02-01

A proposed design analysis is presented of a passive solar energy efficient system for a typical three level, three bedroom, two story, garage under townhouse. The design incorporates the best, most performance proven and cost effective products, materials, processes, technologies, and subsystems which are available today. Seven distinct categories recognized for analysis are identified as: the exterior environment; the interior environment; conservation of energy; natural energy utilization; auxiliary energy utilization; control and distribution systems; and occupant adaptation. Preliminary design features, fenestration systems, the plenum supply system, the thermal storage party fire walls, direct gain storage, the radiant comfort system, and direct passive cooling systems are briefly described.

Evolution of certain typical and atypical features in a case of subacute sclerosing panencephalitis

PubMed Central

Raut, Tushar Premraj; Singh, Maneesh Kumar; Garg, Ravindra Kumar; Rai, Dheeraj

2012-01-01

Subacute sclerosing panencephalitis (SSPE) is a slowly progressive inflammatory disease of the central nervous system caused by a persistent measles virus usually affecting the childhood and adolescent age group. Clinical features at onset are very subtle and non-specific. Certain atypical features can occur at onset or during the course of illness which can be misleading. Neuroimaging features often are non-specific. Features like myoclonic jerks, cognitive decline and typical EEG findings lead to a strong suspicion of SSPE. Here, we describe the stagewise progression of a case of SSPE in a 14-year-old girl who had myoclonic jerks and cognitive decline at onset. During the course of disease, the patient developed cortical vision loss, atypical extrapyramidal features like segmental and hemifacial dystonia ultimately leading to a bedbound vegetative state. EEG showed typical periodic discharges along with positive cerebrospinal fluid serology for measles. PMID:23266775

Evolution of certain typical and atypical features in a case of subacute sclerosing panencephalitis.

PubMed

Raut, Tushar Premraj; Singh, Maneesh Kumar; Garg, Ravindra Kumar; Rai, Dheeraj

2012-12-23

Subacute sclerosing panencephalitis (SSPE) is a slowly progressive inflammatory disease of the central nervous system caused by a persistent measles virus usually affecting the childhood and adolescent age group. Clinical features at onset are very subtle and non-specific. Certain atypical features can occur at onset or during the course of illness which can be misleading. Neuroimaging features often are non-specific. Features like myoclonic jerks, cognitive decline and typical EEG findings lead to a strong suspicion of SSPE. Here, we describe the stagewise progression of a case of SSPE in a 14-year-old girl who had myoclonic jerks and cognitive decline at onset. During the course of disease, the patient developed cortical vision loss, atypical extrapyramidal features like segmental and hemifacial dystonia ultimately leading to a bedbound vegetative state. EEG showed typical periodic discharges along with positive cerebrospinal fluid serology for measles.

Model-Based Learning of Local Image Features for Unsupervised Texture Segmentation

NASA Astrophysics Data System (ADS)

Kiechle, Martin; Storath, Martin; Weinmann, Andreas; Kleinsteuber, Martin

2018-04-01

Features that capture well the textural patterns of a certain class of images are crucial for the performance of texture segmentation methods. The manual selection of features or designing new ones can be a tedious task. Therefore, it is desirable to automatically adapt the features to a certain image or class of images. Typically, this requires a large set of training images with similar textures and ground truth segmentation. In this work, we propose a framework to learn features for texture segmentation when no such training data is available. The cost function for our learning process is constructed to match a commonly used segmentation model, the piecewise constant Mumford-Shah model. This means that the features are learned such that they provide an approximately piecewise constant feature image with a small jump set. Based on this idea, we develop a two-stage algorithm which first learns suitable convolutional features and then performs a segmentation. We note that the features can be learned from a small set of images, from a single image, or even from image patches. The proposed method achieves a competitive rank in the Prague texture segmentation benchmark, and it is effective for segmenting histological images.

Energy and life-cycle cost analysis of a six-story office building

NASA Astrophysics Data System (ADS)

Turiel, I.

1981-10-01

An energy analysis computer program, DOE-2, was used to compute annual energy use for a typical office building as originally designed and with several energy conserving design modifications. The largest energy use reductions were obtained with the incorporation of daylighting techniques, the use of double pane windows, night temperature setback, and the reduction of artificial lighting levels. A life-cycle cost model was developed to assess the cost-effectiveness of the design modifications discussed. The model incorporates such features as inclusion of taxes, depreciation, and financing of conservation investments. The energy conserving strategies are ranked according to economic criteria such as net present benefit, discounted payback period, and benefit to cost ratio.

Defeating feature fatigue.

PubMed

Rust, Roland T; Thompson, Debora Viana; Hamilton, Rebecca W

2006-02-01

Consider a coffeemaker that offers 12 drink options, a car with more than 700 features on the dashboard, and a mouse pad that's also a clock, calculator, and FM radio. All are examples of "feature bloat", or "featuritis", the result of an almost irresistible temptation to load products with lots of bells and whistles. The problem is that the more features a product boasts, the harder it is to use. Manufacturers that increase a product's capability--the number of useful functions it can perform--at the expense of its usability are exposing their customers to feature fatigue. The authors have conducted three studies to gain a better understanding of how consumers weigh a product's capability relative to its usability. They found that even though consumers know that products with more features are harder to use, they initially choose high-feature models. They also pile on more features when given the chance to customize a product for their needs. Once consumers have actually worked with a product, however, usability starts to matter more to them than capability. For managers in consumer products companies, these findings present a dilemma: Should they maximize initial sales by designing high-feature models, which consumers consistently choose, or should they limit the number of features in order to enhance the lifetime value of their customers? The authors' analytical model guides companies toward a happy middle ground: maximizing the net present value of the typical customer's profit stream. The authors also advise companies to build simpler products, help consumers learn which products suit their needs, develop products that do one thing very well, and design market research in which consumers use actual products or prototypes.

Variable Use of Features Associated with African American English by Typically Developing Children

ERIC Educational Resources Information Center

Jackson, Janice E.; Pearson, Barbara Zurer

2010-01-01

Purpose: The well-known decline in the use of African American English (AAE) features by groups of school-aged AAE-speaking children was reexamined for patterns of overt-, zero-, and mixed-marking for individual features and individual speakers. Methods: Seven hundred twenty-nine typically developing children between the ages of 4 and 12--511…

Recent developments in BWR fuel design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, S.P.; Noble, L.D.; Wood, J.E.

1991-11-01

Substantial increases in the cost effectiveness and performance capability of boiling water reactor (BWR) fuel designs have been implemented in the past 5 to 7 yr. This increase has been driven by (a) utility desires to lower fuel and operating costs and (b) design innovations that have lowered enrichment requirements, improved thermal-hydraulic performance, and increased discharge exposure. Higher discharge exposures reduce disposal costs for European and Asian utilities and enable US utilities to lengthen operating cycles. A typical BWR reload fuel bundle fabricated today has 25% higher {sup 235}U enrichment and a factor of 2 higher gadolinium loading than onemore » made several years ago. Today's BWR fuel bundles also contain more unheated water reduces the axial water density variation, lowers the void coefficient, and enhances the neutron efficiency of the bundle, reducing both the gadolinium poison and the enrichment requirements. In addition to these general trends, the following unique design innovations have further enhanced the fuel cost efficiency and performance characteristics of BWR fuel: ferrule spacer, part length rods, interactive channel, and bundle enhanced spectral shift. GE's fuel designs offer the flexibility for modern BWR fuel requirements and contain unique design features that enhance flexibility for modern BWR fuel requirements and contain unique design features that enhance flexibility and fuel cycle economics.« less

Perception and Processing of Faces in the Human Brain Is Tuned to Typical Feature Locations

PubMed Central

Schwarzkopf, D. Samuel; Alvarez, Ivan; Lawson, Rebecca P.; Henriksson, Linda; Kriegeskorte, Nikolaus; Rees, Geraint

2016-01-01

Faces are salient social stimuli whose features attract a stereotypical pattern of fixations. The implications of this gaze behavior for perception and brain activity are largely unknown. Here, we characterize and quantify a retinotopic bias implied by typical gaze behavior toward faces, which leads to eyes and mouth appearing most often in the upper and lower visual field, respectively. We found that the adult human visual system is tuned to these contingencies. In two recognition experiments, recognition performance for isolated face parts was better when they were presented at typical, rather than reversed, visual field locations. The recognition cost of reversed locations was equal to ∼60% of that for whole face inversion in the same sample. Similarly, an fMRI experiment showed that patterns of activity evoked by eye and mouth stimuli in the right inferior occipital gyrus could be separated with significantly higher accuracy when these features were presented at typical, rather than reversed, visual field locations. Our findings demonstrate that human face perception is determined not only by the local position of features within a face context, but by whether features appear at the typical retinotopic location given normal gaze behavior. Such location sensitivity may reflect fine-tuning of category-specific visual processing to retinal input statistics. Our findings further suggest that retinotopic heterogeneity might play a role for face inversion effects and for the understanding of conditions affecting gaze behavior toward faces, such as autism spectrum disorders and congenital prosopagnosia. SIGNIFICANCE STATEMENT Faces attract our attention and trigger stereotypical patterns of visual fixations, concentrating on inner features, like eyes and mouth. Here we show that the visual system represents face features better when they are shown at retinal positions where they typically fall during natural vision. When facial features were shown at typical (rather than reversed) visual field locations, they were discriminated better by humans and could be decoded with higher accuracy from brain activity patterns in the right occipital face area. This suggests that brain representations of face features do not cover the visual field uniformly. It may help us understand the well-known face-inversion effect and conditions affecting gaze behavior toward faces, such as prosopagnosia and autism spectrum disorders. PMID:27605606

Generation of flat-top pulsed magnetic fields with feedback control approach.

PubMed

Kohama, Yoshimitsu; Kindo, Koichi

2015-10-01

We describe the construction of a simple, compact, and cost-effective feedback system that produces flat-top field profiles in pulsed magnetic fields. This system is designed for use in conjunction with a typical capacitor-bank driven pulsed magnet and was tested using a 60-T pulsed magnet. With the developed feedback controller, we have demonstrated flat-top magnetic fields as high as 60.64 T with an excellent field stability of ±0.005 T. The result indicates that the flat-top pulsed magnetic field produced features high field stability and an accessible field strength. These features make this system useful for improving the resolution of data with signal averaging.

Ball Aerospace Long Life, Low Temperature Space Cryocoolers

NASA Astrophysics Data System (ADS)

Glaister, D. S.; Gully, W.; Marquardt, E.; Stack, R.

2004-06-01

This paper describes the development, qualification, characterization testing and performance at Ball Aerospace of long life, low temperature (from 4 to 35 K) space cryocoolers. For over a decade, Ball has built long life (>10 year), multi-stage Stirling and Joule-Thomson (J-T) cryocoolers for space applications, with specific performance and design features for low temperature operation. As infrared space missions have continually pushed for operation at longer wavelengths, the applications for these low temperature cryocoolers have increased. The Ball cryocooler technologies have culminated in the flight qualified SB235 Cryocooler and the in-development 6 K NASA/JPL ACTDP (Advanced Cryocooler Technology Development Program) Cryocooler. The SB235 and its model derivative SB235E are 2-stage coolers designed to provide simultaneous cooling at 35 K (typically, for Mercury Cadmium Telluride or MCT detectors) and 100 K (typically, for the optics) and were baselined for the Raytheon SBIRS Low Track Sensor. The Ball ACTDP cooler is a hybrid Stirling/J-T cooler that has completed its preliminary design with an Engineering Model to be tested in 2005. The ACTDP cooler provides simultaneous cooling at 6 K (typically, for either doped Si detectors or as a sub-Kelvin precooler) and 18 K (typically, for optics or shielding). The ACTDP cooler is under development for the NASA JWST (James Webb Space Telescope), TPF (Terrestrial Planet Finder), and Con-X (Constellation X-Ray) missions. Both the SB235 and ACTDP Coolers are highly leveraged off previous Ball space coolers including multiple life test and flight units.

Feature Selection Methods for Zero-Shot Learning of Neural Activity.

PubMed

Caceres, Carlos A; Roos, Matthew J; Rupp, Kyle M; Milsap, Griffin; Crone, Nathan E; Wolmetz, Michael E; Ratto, Christopher R

2017-01-01

Dimensionality poses a serious challenge when making predictions from human neuroimaging data. Across imaging modalities, large pools of potential neural features (e.g., responses from particular voxels, electrodes, and temporal windows) have to be related to typically limited sets of stimuli and samples. In recent years, zero-shot prediction models have been introduced for mapping between neural signals and semantic attributes, which allows for classification of stimulus classes not explicitly included in the training set. While choices about feature selection can have a substantial impact when closed-set accuracy, open-set robustness, and runtime are competing design objectives, no systematic study of feature selection for these models has been reported. Instead, a relatively straightforward feature stability approach has been adopted and successfully applied across models and imaging modalities. To characterize the tradeoffs in feature selection for zero-shot learning, we compared correlation-based stability to several other feature selection techniques on comparable data sets from two distinct imaging modalities: functional Magnetic Resonance Imaging and Electrocorticography. While most of the feature selection methods resulted in similar zero-shot prediction accuracies and spatial/spectral patterns of selected features, there was one exception; A novel feature/attribute correlation approach was able to achieve those accuracies with far fewer features, suggesting the potential for simpler prediction models that yield high zero-shot classification accuracy.

An enhanced digital line graph design

USGS Publications Warehouse

Guptill, Stephen C.

1990-01-01

In response to increasing information demands on its digital cartographic data, the U.S. Geological Survey has designed an enhanced version of the Digital Line Graph, termed Digital Line Graph - Enhanced (DLG-E). In the DLG-E model, the phenomena represented by geographic and cartographic data are termed entities. Entities represent individual phenomena in the real world. A feature is an abstraction of a set of entities, with the feature description encompassing only selected properties of the entities (typically the properties that have been portrayed cartographically on a map). Buildings, bridges, roads, streams, grasslands, and counties are examples of features. A feature instance, that is, one occurrence of a feature, is described in the digital environment by feature objects and spatial objects. A feature object identifies a feature instance and its nonlocational attributes. Nontopological relationships are associated with feature objects. The locational aspects of the feature instance are represented by spatial objects. Four spatial objects (points, nodes, chains, and polygons) and their topological relationships are defined. To link the locational and nonlocational aspects of the feature instance, a given feature object is associated with (or is composed of) a set of spatial objects. These objects, attributes, and relationships are the components of the DLG-E data model. To establish a domain of features for DLG-E, an approach using a set of classes, or views, of spatial entities was adopted. The five views that were developed are cover, division, ecosystem, geoposition, and morphology. The views are exclusive; each view is a self-contained analytical approach to the entire range of world features. Because each view is independent of the others, a single point on the surface of the Earth can be represented under multiple views. Under the five views, over 200 features were identified and defined. This set constitutes an initial domain of DLG-E features.

Pitt-Hopkins Syndrome: A Review of Current Literature, Clinical Approach, and 23-Patient Case Series.

PubMed

Goodspeed, Kimberly; Newsom, Cassandra; Morris, Mary Ann; Powell, Craig; Evans, Patricia; Golla, Sailaja

2018-03-01

Pitt-Hopkins syndrome (PTHS) is a rare, genetic disorder caused by a molecular variant of TCF4 which is involved in embryologic neuronal differentiation. PTHS is characterized by syndromic facies, psychomotor delay, and intellectual disability. Other associated features include early-onset myopia, seizures, constipation, and hyperventilation-apneic spells. Many also meet criteria for autism spectrum disorder. Here the authors present a series of 23 PTHS patients with molecularly confirmed TCF4 variants and describe 3 unique individuals. The first carries a small deletion but does not exhibit the typical facial features nor the typical pattern of developmental delay. The second exhibits typical facial features, but has attained more advanced motor and verbal skills than other reported cases to date. The third displays typical features of PTHS, however inherited a large chromosomal duplication involving TCF4 from his unaffected father with somatic mosaicism. To the authors' knowledge, this is the first chromosomal duplication case reported to date.

Fluidic Emergency Thruster for Aircraft

NASA Technical Reports Server (NTRS)

Honda, T. S.

1972-01-01

The design, development, fabrication and test evaluation of two prototype fluidic emergency thrusters (FET) for aircraft stabilization are discussed. The fluidic control units were designed to provide, between two diametrically opposed nozzles, a thrust differential proportional to an input voltage signal. The emergency roll control requirements of the X-14 VTOL research aircraft were defined as typical design goals. Two control units, one on each wing tip, are intended to provide a maximum thrust of 224 pounds per unit. The units are designed to operate with 2500 psig, 2000 F gas from a solid propellant gas generator. The emergency system including the gas generator was designed to add less than 11 pounds per wing tip. The operating time under emergency conditions was specified as five seconds. The fluidic emergency thruster is similar in concept to a JATO system but has the added feature of controllable thrust.

Optimal number of features as a function of sample size for various classification rules.

PubMed

Hua, Jianping; Xiong, Zixiang; Lowey, James; Suh, Edward; Dougherty, Edward R

2005-04-15

Given the joint feature-label distribution, increasing the number of features always results in decreased classification error; however, this is not the case when a classifier is designed via a classification rule from sample data. Typically (but not always), for fixed sample size, the error of a designed classifier decreases and then increases as the number of features grows. The potential downside of using too many features is most critical for small samples, which are commonplace for gene-expression-based classifiers for phenotype discrimination. For fixed sample size and feature-label distribution, the issue is to find an optimal number of features. Since only in rare cases is there a known distribution of the error as a function of the number of features and sample size, this study employs simulation for various feature-label distributions and classification rules, and across a wide range of sample and feature-set sizes. To achieve the desired end, finding the optimal number of features as a function of sample size, it employs massively parallel computation. Seven classifiers are treated: 3-nearest-neighbor, Gaussian kernel, linear support vector machine, polynomial support vector machine, perceptron, regular histogram and linear discriminant analysis. Three Gaussian-based models are considered: linear, nonlinear and bimodal. In addition, real patient data from a large breast-cancer study is considered. To mitigate the combinatorial search for finding optimal feature sets, and to model the situation in which subsets of genes are co-regulated and correlation is internal to these subsets, we assume that the covariance matrix of the features is blocked, with each block corresponding to a group of correlated features. Altogether there are a large number of error surfaces for the many cases. These are provided in full on a companion website, which is meant to serve as resource for those working with small-sample classification. For the companion website, please visit http://public.tgen.org/tamu/ofs/ e-dougherty@ee.tamu.edu.

A Cross-Sectional Investigation of the Importance of Park Features for Promoting Regular Physical Activity in Parks.

PubMed

Costigan, Sarah A; Veitch, Jenny; Crawford, David; Carver, Alison; Timperio, Anna

2017-11-02

Parks in the US and Australia are generally underutilised, and park visitors typically engage in low levels of physical activity (PA). Better understanding park features that may encourage visitors to be active is important. This study examined the perceived importance of park features for encouraging park-based PA and examined differences by sex, age, parental-status and participation in PA. Cross-sectional surveys were completed by local residents ( n = 2775) living near two parks (2013/2015). Demographic variables, park visitation and leisure-time PA were self-reported, respondents rated the importance of 20 park features for encouraging park-based PA in the next fortnight. Chi-square tests of independence examined differences in importance of park features for PA among sub-groups of local residents (sex, age, parental-status, PA). Park features ranked most important for park-based PA were: well maintained (96.2%), feel safe (95.4%), relaxing atmosphere (91.2%), easy to get to (91.7%), and shady trees (90.3%). All subgroups ranked 'well maintained' as most important. Natural and built environment features of parks are important for promoting adults' park-based PA, and should be considered in park (re)design.

NASA Manufacturing and Test Requirements for Normally Closed Pyrovalves for Hazardous Flight Systems Applications

NASA Technical Reports Server (NTRS)

McDougle, Stephen H.

2015-01-01

Pyrovalves (figure 1, Basic Pyrovalve Design and Features,) are typically lighter, more reliable, and in most cases less expensive than other types of valves. They also consume less electrical power. They are single-use devices that are used in propulsion systems to isolate propellants or pressurant gases. These fluids may be hazardous because of their toxicity, reactivity, temperature, or high pressure. Note that in the simplified block diagram below not all detail features are shown so that those of major interest are more prominent. The diagram is provided to point out the various features that are discussed in this Specification. Features of some NC parent metal valve designs may differ. In 2013, the NESC concluded an extensive study of the reliability and safety of NC parent metal valves used in payloads carried aboard ELVs. The assessment successfully evaluated technical data to determine the risk of NC parent metal valve leakage or inadvertent activation in ELV payloads. The study resulted in numerous recommendations to ensure personnel and hardware/facility safety during ground processing of ELV payloads. One of those recommendations was to establish a NASA specification for NC parent metal valves. This Specification is a result of that recommendation, which is documented in NESC-RP-10-00614.

Statistical molecular design of balanced compound libraries for QSAR modeling.

PubMed

Linusson, A; Elofsson, M; Andersson, I E; Dahlgren, M K

2010-01-01

A fundamental step in preclinical drug development is the computation of quantitative structure-activity relationship (QSAR) models, i.e. models that link chemical features of compounds with activities towards a target macromolecule associated with the initiation or progression of a disease. QSAR models are computed by combining information on the physicochemical and structural features of a library of congeneric compounds, typically assembled from two or more building blocks, and biological data from one or more in vitro assays. Since the models provide information on features affecting the compounds' biological activity they can be used as guides for further optimization. However, in order for a QSAR model to be relevant to the targeted disease, and drug development in general, the compound library used must contain molecules with balanced variation of the features spanning the chemical space believed to be important for interaction with the biological target. In addition, the assays used must be robust and deliver high quality data that are directly related to the function of the biological target and the associated disease state. In this review, we discuss and exemplify the concept of statistical molecular design (SMD) in the selection of building blocks and final synthetic targets (i.e. compounds to synthesize) to generate information-rich, balanced libraries for biological testing and computation of QSAR models.

Probabilistic Methods for Uncertainty Propagation Applied to Aircraft Design

NASA Technical Reports Server (NTRS)

Green, Lawrence L.; Lin, Hong-Zong; Khalessi, Mohammad R.

2002-01-01

Three methods of probabilistic uncertainty propagation and quantification (the method of moments, Monte Carlo simulation, and a nongradient simulation search method) are applied to an aircraft analysis and conceptual design program to demonstrate design under uncertainty. The chosen example problems appear to have discontinuous design spaces and thus these examples pose difficulties for many popular methods of uncertainty propagation and quantification. However, specific implementation features of the first and third methods chosen for use in this study enable successful propagation of small uncertainties through the program. Input uncertainties in two configuration design variables are considered. Uncertainties in aircraft weight are computed. The effects of specifying required levels of constraint satisfaction with specified levels of input uncertainty are also demonstrated. The results show, as expected, that the designs under uncertainty are typically heavier and more conservative than those in which no input uncertainties exist.

A potentiostat featuring an integrator transimpedance amplifier for the measurement of very low currents--Proof-of-principle application in microfluidic separations and voltammetry.

PubMed

Koutilellis, G D; Economou, A; Efstathiou, C E

2016-03-01

This work reports the design and construction of a novel potentiostat which features an integrator transimpedance amplifier as a current-monitoring unit. The integration approach addresses the limitations of the feedback resistor approach used for current monitoring in conventional potentiostat designs. In the present design, measurement of the current is performed by a precision switched integrator transimpedance amplifier operated in the dual sampling mode which enables sub-pA resolution. The potentiostat is suitable for measuring very low currents (typical dynamic range: 5 pA-4.7 μA) with a 16 bit resolution, and it can support 2-, 3- and 4-electrode cell configurations. Its operation was assessed by using it as a detection module in a home-made capillary electrophoresis system for the separation and amperometric detection of paracetamol and p-aminophenol at a 3-electrode microfluidic chip. The potential and limitations of the proposed potentiostat to implement fast potential-scan voltammetric techniques were demonstrated for the case of cyclic voltammetry.

A potentiostat featuring an integrator transimpedance amplifier for the measurement of very low currents—Proof-of-principle application in microfluidic separations and voltammetry

NASA Astrophysics Data System (ADS)

Koutilellis, G. D.; Economou, A.; Efstathiou, C. E.

2016-03-01

This work reports the design and construction of a novel potentiostat which features an integrator transimpedance amplifier as a current-monitoring unit. The integration approach addresses the limitations of the feedback resistor approach used for current monitoring in conventional potentiostat designs. In the present design, measurement of the current is performed by a precision switched integrator transimpedance amplifier operated in the dual sampling mode which enables sub-pA resolution. The potentiostat is suitable for measuring very low currents (typical dynamic range: 5 pA-4.7 μA) with a 16 bit resolution, and it can support 2-, 3- and 4-electrode cell configurations. Its operation was assessed by using it as a detection module in a home-made capillary electrophoresis system for the separation and amperometric detection of paracetamol and p-aminophenol at a 3-electrode microfluidic chip. The potential and limitations of the proposed potentiostat to implement fast potential-scan voltammetric techniques were demonstrated for the case of cyclic voltammetry.

Inefficient conjunction search made efficient by concurrent spoken delivery of target identity.

PubMed

Reali, Florencia; Spivey, Michael J; Tyler, Melinda J; Terranova, Joseph

2006-08-01

Visual search based on a conjunction of two features typically elicits reaction times that increase linearly as a function of the number of distractors, whereas search based on a single feature is essentially unaffected by set size. These and related findings have often been interpreted as evidence of a serial search stage that follows a parallel search stage. However, a wide range of studies has been showing a form of blending of these two processes. For example, when a spoken instruction identifies the conjunction target concurrently with the visual display, the effect of set size is significantly reduced, suggesting that incremental linguistic processing of the first feature adjective and then the second feature adjective may facilitate something approximating a parallel extraction of objects during search for the target. Here, we extend these results to a variety of experimental designs. First, we replicate the result with a mixed-trials design (ruling out potential strategies associated with the blocked design of the original study). Second, in a mixed-trials experiment, the order of adjective types in the spoken query varies randomly across conditions. In a third experiment, we extend the effect to a triple-conjunction search task. A fourth (control) experiment demonstrates that these effects are not due to an efficient odd-one-out search that ignores the linguistic input. This series of experiments, along with attractor-network simulations of the phenomena, provide further evidence toward understanding linguistically mediated influences in real-time visual search processing.

Fast traffic sign recognition with a rotation invariant binary pattern based feature.

PubMed

Yin, Shouyi; Ouyang, Peng; Liu, Leibo; Guo, Yike; Wei, Shaojun

2015-01-19

Robust and fast traffic sign recognition is very important but difficult for safe driving assistance systems. This study addresses fast and robust traffic sign recognition to enhance driving safety. The proposed method includes three stages. First, a typical Hough transformation is adopted to implement coarse-grained location of the candidate regions of traffic signs. Second, a RIBP (Rotation Invariant Binary Pattern) based feature in the affine and Gaussian space is proposed to reduce the time of traffic sign detection and achieve robust traffic sign detection in terms of scale, rotation, and illumination. Third, the techniques of ANN (Artificial Neutral Network) based feature dimension reduction and classification are designed to reduce the traffic sign recognition time. Compared with the current work, the experimental results in the public datasets show that this work achieves robustness in traffic sign recognition with comparable recognition accuracy and faster processing speed, including training speed and recognition speed.

Spatial feature tracking impedence sensor using multiple electric fields

DOEpatents

Novak, J.L.

1998-08-11

Linear and other features on a workpiece are tracked by measuring the fields generated between electrodes arrayed in pairs. One electrode in each pair operates as a transmitter and the other as a receiver, and both electrodes in a pair are arrayed on a carrier. By combining and subtracting fields between electrodes in one pair and between a transmitting electrode in one pair and a receiving electrode in another pair, information describing the location and orientation of the sensor relative to the workpiece in up to six degrees of freedom may be obtained. Typical applications will measure capacitance, but other impedance components may be measured as well. The sensor is designed to track a linear feature axis or a protrusion or pocket in a workpiece. Seams and ridges can be tracked by this non-contact sensor. The sensor output is useful for robotic applications. 10 figs.

Fast Traffic Sign Recognition with a Rotation Invariant Binary Pattern Based Feature

PubMed Central

Yin, Shouyi; Ouyang, Peng; Liu, Leibo; Guo, Yike; Wei, Shaojun

2015-01-01

Robust and fast traffic sign recognition is very important but difficult for safe driving assistance systems. This study addresses fast and robust traffic sign recognition to enhance driving safety. The proposed method includes three stages. First, a typical Hough transformation is adopted to implement coarse-grained location of the candidate regions of traffic signs. Second, a RIBP (Rotation Invariant Binary Pattern) based feature in the affine and Gaussian space is proposed to reduce the time of traffic sign detection and achieve robust traffic sign detection in terms of scale, rotation, and illumination. Third, the techniques of ANN (Artificial Neutral Network) based feature dimension reduction and classification are designed to reduce the traffic sign recognition time. Compared with the current work, the experimental results in the public datasets show that this work achieves robustness in traffic sign recognition with comparable recognition accuracy and faster processing speed, including training speed and recognition speed. PMID:25608217

Spatial feature tracking impedence sensor using multiple electric fields

DOEpatents

Novak, James L.

1998-01-01

Linear and other features on a workpiece are tracked by measuring the fields generated between electrodes arrayed in pairs. One electrode in each pair operates as a transmitter and the other as a receiver, and both electrodes in a pair are arrayed on a carrier. By combining and subtracting fields between electrodes in one pair and between a transmitting electrode in one pair and a receiving electrode in another pair, information describing the location and orientation of the sensor relative to the workpiece in up to six degrees of freedom may be obtained. Typical applications will measure capacitance, but other impedance components may be measured as well. The sensor is designed to track a linear feature axis or a protrusion or pocket in a workpiece. Seams and ridges can be tracked by this non-contact sensor. The sensor output is useful for robotic applications.

Screw compressor analysis from a vibration point-of-view

NASA Astrophysics Data System (ADS)

Hübel, D.; Žitek, P.

2017-09-01

Vibrations are a very typical feature of all compressors and are given great attention in the industry. The reason for this interest is primarily the negative influence that it can have on both the operating staff and the entire machine's service life. The purpose of this work is to describe the methodology of screw compressor analysis from a vibration point-of-view. This analysis is an essential part of the design of vibro-diagnostics of screw compressors with regard to their service life.

Simulation of wear in overhead current collection systems

NASA Astrophysics Data System (ADS)

Klapas, D.; Benson, F. A.; Hackam, R.

1985-09-01

Apparatus have been designed to simulate the wear from conductors in a railway current collection system. The main features of the wear machine include a continuous monitoring of the strip wear, strip traversing, and dwell-time test facilities for the investigation of oxidational wear on a copper disk, simulating the contact wire. Disk wear is measured in situ by the spherical indentations method. Typical results of the specific wear rate are also presented to demonstrate the capability of the apparatus.

Fiber-Optic Terahertz Data-Communication Networks

NASA Technical Reports Server (NTRS)

Chua, Peter L.; Lambert, James L.; Morookian, John M.; Bergman, Larry A.

1994-01-01

Network protocols implemented in optical domain. Fiber-optic data-communication networks utilize fully available bandwidth of single-mode optical fibers. Two key features of method: use of subpicosecond laser pulses as carrier signals and spectral phase modulation of pulses for optical implementation of code-division multiple access as multiplexing network protocol. Local-area network designed according to concept offers full crossbar functionality, security of data in transit through network, and capacity about 100 times that of typical fiber-optic local-area network in current use.

Peer assessment of personality traits and pathology in female college students.

PubMed

Oltmanns, T F; Turkheimer, E; Strauss, M E

1998-03-01

Assessment procedures for personality disorders (PDs) typically rely on self-reports, even though some people with PDs may be unable to view themselves realistically or are unwilling to report socially undesirable traits. Close associates may provide important information regarding the presence of PD traits. Peer nomination is a reliable and valid assessment procedure that can be adapted to the study of PDs for research purposes. This study focused on characteristic features that define narcissistic, dependent, and obsessive-compulsive PDs using information collected from both self and others in a nonclinical sample of women. It was designed to identify specific areas of agreement and discrepancy between self-report and peer assessment in the measurement of characteristic features of these disorders.

Ultra-Widefield Steering-Based SD-OCT Imaging of the Retinal Periphery

PubMed Central

Choudhry, Netan; Golding, John; Manry, Matthew W.; Rao, Rajesh C.

2016-01-01

Objective To describe the spectral-domain optical coherence tomography (SD-OCT) features of peripheral retinal findings using an ultra-widefield (UWF) steering technique to image the retinal periphery. Design Observational study. Participants 68 patients (68 eyes) with 19 peripheral retinal features. Main Outcome Measures SD-OCT-based structural features. Methods Nineteen peripheral retinal features including: vortex vein, congenital hypertrophy of the retinal pigment epithelium (CHRPE), pars plana, ora serrata pearl, typical cystoid degeneration (TCD), cystic retinal tuft, meridional fold, lattice and cobblestone degeneration, retinal hole, retinal tear, rhegmatogenous retinal detachment (RRD), typical degenerative senile retinoschisis, peripheral laser coagulation scars, ora tooth, cryopexy scars (retinal tear and treated retinoblastoma scar), bone spicules, white without pressure, and peripheral drusen were identified by peripheral clinical examination. Near infrared (NIR) scanning laser ophthalmoscopy (SLO) images and SD-OCT of these entities were registered to UWF color photographs. Results SD-OCT resolved structural features of all peripheral findings. Dilated hyporeflective tubular structures within the choroid were observed in the vortex vein. Loss of retinal lamination, neural retinal attenuation, RPE loss or hypertrophy were seen in several entities including CHRPE, ora serrata pearl, TCD, cystic retinal tuft, meridional fold, lattice and cobblestone degenerations. Hyporeflective intraretinal spaces, indicating cystoid or schitic fluid, were seen in ora serrata pearl, ora tooth, TCD, cystic retinal tuft, meridional fold, retinal hole, and typical degenerative senile retinoschisis. The vitreoretinal interface, which often consisted of lamellae-like structures of the condensed cortical vitreous near or adherent to the neural retina, appeared clearly in most peripheral findings, confirming its association with many low-risk and vision-threatening pathologies such as lattice degeneration, meridional folds, retinal breaks, and RRDs. Conclusions UWF steering technique-based SD-OCT imaging of the retinal periphery is feasible with current commercially available devices, and provides detailed anatomical information of the peripheral retina, including benign and pathological entities, not previously imaged. This imaging technique may deepen our structural understanding of these entities, their potentially associated macular and systemic pathologies, and may influence decision-making in clinical practice, particularly in areas with teleretinal capabilities but poor access to retinal specialists. PMID:26992837

Predicting and analyzing DNA-binding domains using a systematic approach to identifying a set of informative physicochemical and biochemical properties

PubMed Central

2011-01-01

Background Existing methods of predicting DNA-binding proteins used valuable features of physicochemical properties to design support vector machine (SVM) based classifiers. Generally, selection of physicochemical properties and determination of their corresponding feature vectors rely mainly on known properties of binding mechanism and experience of designers. However, there exists a troublesome problem for designers that some different physicochemical properties have similar vectors of representing 20 amino acids and some closely related physicochemical properties have dissimilar vectors. Results This study proposes a systematic approach (named Auto-IDPCPs) to automatically identify a set of physicochemical and biochemical properties in the AAindex database to design SVM-based classifiers for predicting and analyzing DNA-binding domains/proteins. Auto-IDPCPs consists of 1) clustering 531 amino acid indices in AAindex into 20 clusters using a fuzzy c-means algorithm, 2) utilizing an efficient genetic algorithm based optimization method IBCGA to select an informative feature set of size m to represent sequences, and 3) analyzing the selected features to identify related physicochemical properties which may affect the binding mechanism of DNA-binding domains/proteins. The proposed Auto-IDPCPs identified m=22 features of properties belonging to five clusters for predicting DNA-binding domains with a five-fold cross-validation accuracy of 87.12%, which is promising compared with the accuracy of 86.62% of the existing method PSSM-400. For predicting DNA-binding sequences, the accuracy of 75.50% was obtained using m=28 features, where PSSM-400 has an accuracy of 74.22%. Auto-IDPCPs and PSSM-400 have accuracies of 80.73% and 82.81%, respectively, applied to an independent test data set of DNA-binding domains. Some typical physicochemical properties discovered are hydrophobicity, secondary structure, charge, solvent accessibility, polarity, flexibility, normalized Van Der Waals volume, pK (pK-C, pK-N, pK-COOH and pK-a(RCOOH)), etc. Conclusions The proposed approach Auto-IDPCPs would help designers to investigate informative physicochemical and biochemical properties by considering both prediction accuracy and analysis of binding mechanism simultaneously. The approach Auto-IDPCPs can be also applicable to predict and analyze other protein functions from sequences. PMID:21342579

Feature Selection Methods for Zero-Shot Learning of Neural Activity

PubMed Central

Caceres, Carlos A.; Roos, Matthew J.; Rupp, Kyle M.; Milsap, Griffin; Crone, Nathan E.; Wolmetz, Michael E.; Ratto, Christopher R.

2017-01-01

Dimensionality poses a serious challenge when making predictions from human neuroimaging data. Across imaging modalities, large pools of potential neural features (e.g., responses from particular voxels, electrodes, and temporal windows) have to be related to typically limited sets of stimuli and samples. In recent years, zero-shot prediction models have been introduced for mapping between neural signals and semantic attributes, which allows for classification of stimulus classes not explicitly included in the training set. While choices about feature selection can have a substantial impact when closed-set accuracy, open-set robustness, and runtime are competing design objectives, no systematic study of feature selection for these models has been reported. Instead, a relatively straightforward feature stability approach has been adopted and successfully applied across models and imaging modalities. To characterize the tradeoffs in feature selection for zero-shot learning, we compared correlation-based stability to several other feature selection techniques on comparable data sets from two distinct imaging modalities: functional Magnetic Resonance Imaging and Electrocorticography. While most of the feature selection methods resulted in similar zero-shot prediction accuracies and spatial/spectral patterns of selected features, there was one exception; A novel feature/attribute correlation approach was able to achieve those accuracies with far fewer features, suggesting the potential for simpler prediction models that yield high zero-shot classification accuracy. PMID:28690513

A new airborne laser-induced fluorescence instrument for in situ detection of formaldehyde throughout the troposphere and lower stratosphere

NASA Astrophysics Data System (ADS)

Cazorla, M.; Wolfe, G. M.; Bailey, S. A.; Swanson, A. K.; Arkinson, H. L.; Hanisco, T. F.

2015-02-01

The NASA In Situ Airborne Formaldehyde (ISAF) instrument is a high-performance laser-based detector for gas-phase formaldehyde (HCHO). ISAF uses rotational-state specific laser excitation at 353 nm for laser-induced fluorescence (LIF) detection of HCHO. A number of features make ISAF ideal for airborne deployment, including (1) a compact, low-maintenance fiber laser, (2) a single-pass design for stable signal response, (3) a straightforward inlet design, and (4) a stand-alone data acquisition system. A full description of the instrument design is given, along with detailed performance characteristics. The accuracy of reported mixing ratios is ±10% based on calibration against IR and UV absorption of a primary HCHO standard. Precision at 1 Hz is typically better than 20% above 100 pptv, with uncertainty in the signal background contributing most to variability at low mixing ratios. The 1 Hz detection limit for a signal / noise ratio of 2 is 36 pptv for 10 mW of laser power, and the e fold time response at typical sample flow rates is 0.19 s. ISAF has already flown on several field missions and platforms with excellent results.

A new airborne laser-induced fluorescence instrument for in situ detection of Formaldehyde throughout the troposphere and lower stratosphere

NASA Astrophysics Data System (ADS)

Cazorla, M.; Wolfe, G. M.; Bailey, S. A.; Swanson, A. K.; Arkinson, H. L.; Hanisco, T. F.

2014-08-01

The NASA In Situ Airborne Formaldehyde (ISAF) instrument is a high-performance laser-based detector for gas phase formaldehyde (HCHO). ISAF uses rotational-state specific laser excitation at 353 nm for laser-induced fluorescence (LIF) detection of HCHO. A number of features make ISAF ideal for airborne deployment, including (1) a compact, low-maintenance fiber laser, (2) a single-pass design for stable signal response, (3) a straightforward inlet design, and (4) a standalone data acquisition system. A full description of the instrument design is given, along with detailed performance characteristics. The accuracy of reported mixing ratios is ±10% based on calibration against IR and UV absorption of a primary HCHO standard. Precision at 1 Hz is typically better than 20% above 100 pptv, with uncertainty in the signal background contributing most to variability at low mixing ratios. The 1 Hz detection limit for a signal/noise ratio of 2 is 36 pptv for 10 mW of laser power, and the e-fold time response at typical sample flow rates is 0.19 s. ISAF has already flown on several field missions and platforms with excellent results.

The Value of Interrupted Time-Series Experiments for Community Intervention Research

PubMed Central

Biglan, Anthony; Ary, Dennis; Wagenaar, Alexander C.

2015-01-01

Greater use of interrupted time-series experiments is advocated for community intervention research. Time-series designs enable the development of knowledge about the effects of community interventions and policies in circumstances in which randomized controlled trials are too expensive, premature, or simply impractical. The multiple baseline time-series design typically involves two or more communities that are repeatedly assessed, with the intervention introduced into one community at a time. It is particularly well suited to initial evaluations of community interventions and the refinement of those interventions. This paper describes the main features of multiple baseline designs and related repeated-measures time-series experiments, discusses the threats to internal validity in multiple baseline designs, and outlines techniques for statistical analyses of time-series data. Examples are given of the use of multiple baseline designs in evaluating community interventions and policy changes. PMID:11507793

A quick response four decade logarithmic high-voltage stepping supply

NASA Technical Reports Server (NTRS)

Doong, H.

1978-01-01

An improved high-voltage stepping supply, for space instrumentation is described where low power consumption and fast settling time between steps are required. The high-voltage stepping supply, utilizing an average power of 750 milliwatts, delivers a pair of mirror images with 64 level logarithmic outputs. It covers a four decade range of + or - 2500 to + or - 0.29 volts having an output stability of + or - 0.5 percent or + or - 20 millivolts for all line load and temperature variations. The supply provides a typical step setting time of 1 millisecond with 100 microseconds for the lower two decades. The versatile design features of the high-voltage stepping supply provides a quick response staircase generator as described or a fixed voltage with the option to change levels as required over large dynamic ranges without circuit modifications. The concept can be implemented up to + or - 5000 volts. With these design features, the high-voltage stepping supply should find numerous applications where charged particle detection, electro-optical systems, and high voltage scientific instruments are used.

Face processing in Williams syndrome is already atypical in infancy.

PubMed

D'Souza, Dean; Cole, Victoria; Farran, Emily K; Brown, Janice H; Humphreys, Kate; Howard, John; Rodic, Maja; Dekker, Tessa M; D'Souza, Hana; Karmiloff-Smith, Annette

2015-01-01

Face processing is a crucial socio-cognitive ability. Is it acquired progressively or does it constitute an innately-specified, face-processing module? The latter would be supported if some individuals with seriously impaired intelligence nonetheless showed intact face-processing abilities. Some theorists claim that Williams syndrome (WS) provides such evidence since, despite IQs in the 50s, adolescents/adults with WS score in the normal range on standardized face-processing tests. Others argue that atypical neural and cognitive processes underlie WS face-processing proficiencies. But what about infants with WS? Do they start with typical face-processing abilities, with atypicality developing later, or are atypicalities already evident in infancy? We used an infant familiarization/novelty design and compared infants with WS to typically developing controls as well as to a group of infants with Down syndrome matched on both mental and chronological age. Participants were familiarized with a schematic face, after which they saw a novel face in which either the features (eye shape) were changed or just the configuration of the original features. Configural changes were processed successfully by controls, but not by infants with WS who were only sensitive to featural changes and who showed syndrome-specific profiles different from infants with the other neurodevelopmental disorder. Our findings indicate that theorists can no longer use the case of WS to support claims that evolution has endowed the human brain with an independent face-processing module.

Familiarity effects in the construction of facial-composite images using modern software systems.

PubMed

Frowd, Charlie D; Skelton, Faye C; Butt, Neelam; Hassan, Amal; Fields, Stephen; Hancock, Peter J B

2011-12-01

We investigate the effect of target familiarity on the construction of facial composites, as used by law enforcement to locate criminal suspects. Two popular software construction methods were investigated. Participants were shown a target face that was either familiar or unfamiliar to them and constructed a composite of it from memory using a typical 'feature' system, involving selection of individual facial features, or one of the newer 'holistic' types, involving repeated selection and breeding from arrays of whole faces. This study found that composites constructed of a familiar face were named more successfully than composites of an unfamiliar face; also, naming of composites of internal and external features was equivalent for construction of unfamiliar targets, but internal features were better named than the external features for familiar targets. These findings applied to both systems, although benefit emerged for the holistic type due to more accurate construction of internal features and evidence for a whole-face advantage. STATEMENT OF RELEVANCE: This work is of relevance to practitioners who construct facial composites with witnesses to and victims of crime, as well as for software designers to help them improve the effectiveness of their composite systems.

Design and initial application of the extended aircraft interrogation and display system: Multiprocessing ground support equipment for digital flight systems

NASA Technical Reports Server (NTRS)

Glover, Richard D.

1987-01-01

A pipelined, multiprocessor, general-purpose ground support equipment for digital flight systems has been developed and placed in service at the NASA Ames Research Center's Dryden Flight Research Facility. The design is an outgrowth of the earlier aircraft interrogation and display system (AIDS) used in support of several research projects to provide engineering-units display of internal control system parameters during development and qualification testing activities. The new system, incorporating multiple 16-bit processors, is called extended AIDS (XAIDS) and is now supporting the X-29A forward-swept-wing aircraft project. This report describes the design and mechanization of XAIDS and shows the steps whereby a typical user may take advantage of its high throughput and flexible features.

Modification of PBDEs (BDE-15, BDE-47, BDE-85 and BDE-126) biological toxicity, bio-concentration, persistence and atmospheric long-range transport potential based on the pharmacophore modeling assistant with the full factor experimental design.

PubMed

Jiang, Long; Li, Yu

2016-04-15

In this study, the properties of AhR binding affinity, bio-concentration factor, half-life and vapor pressure were selected as the typical indicators of biological toxicity, bio-concentration, persistence and atmospheric long-range transport potential for polybrominated diphenyl ethers (PBDEs), respectively. A three-dimensional pharmacophore modeling assistant with a full factor experimental design for each property was used to reveal the significant pharmacophore features and the substituent effects to obtain reasonable modified schemes for the selected target PBDEs. Finally, the performances of the persistent organic pollutant (POP) properties, the synthesis feasibility and the fire resistance of the modified compounds were evaluated. The most influential pharmacophore feature for all POP properties was the hydrophobic group, especially the vinyl and propyl groups. Modified compounds with two additional hydrophobic groups exhibited a better regulatory performance. The average reduction in the proportions of the four POP properties for the modified compounds (except for 3-phenyl-BDE-15) was 70.60%, 52.44%, 47.04% and 70.88%. In addition, the energy and the C-Br bond dissociation enthalpy of the four typical PBDEs were higher than those of the modified compounds (except for 3-phenyl-BDE-15), indicating the synthesis feasibility and the lower energy barrier of the modified compounds to release Br free radicals to provide fire resistance. Copyright © 2015 Elsevier B.V. All rights reserved.

Power conditioning equipment for a thermoelectric outer planet spacecraft, volume 1, book 2

NASA Technical Reports Server (NTRS)

Andrews, R. E. (Editor)

1972-01-01

The design and development of power conditioning equipment for the thermoelectric outer planet spacecraft program are considered. One major aspect of the program included the design, assembly and test of various breadboard power conditioning elements. Among others these included a quad-redundant shunt regulator, a high voltage traveling wave tube dc-to-dc converter, two-phase gyro inverters and numerous solid state switching circuits. Many of these elements were arranged in a typical subsystem configuration and tests were conducted which demonstrated basic element compatibility. In parallel with the development of the basic power conditioning elements, system studies were continued. The salient features of the selected power subsystem configuration are presented.

The use of a modified semantic features analysis approach in aphasia.

PubMed

Hashimoto, Naomi; Frome, Amber

2011-01-01

Several studies have reported improved naming using the semantic feature analysis (SFA) approach in individuals with aphasia. Whether the SFA can be modified and still produce naming improvements in aphasia is unknown. The present study was designed to address this question by using a modified version of the SFA approach. Three, rather than the typical six, features were used, and written along with verbal responses were allowed in an individual with both aphasia and apraxia of speech. A single-subject multiple-baseline design across behaviors was used to treat naming of single objects across three different semantic categories in a 72-year-old individual with aphasia and apraxia of speech. Stimulus generalization of training was measured by using photographs of trained items presented in natural contexts. Training of the three different categories resulted in improved naming. At a 6-week follow-up session, naming remained above pre-treatment levels but declines were noted compared to treatment levels. Generalization to the same trained items presented in different contexts was also demonstrated although declines in performance were also noted over time. Results of the study provide qualified support for the use of three features in promoting long-term improvement of naming in an individual with both aphasia and apraxia of speech. Future SFA studies should focus on whether it is the number or types of features used, aphasia severity, or length of treatment that are critical factors in rehabilitating naming deficits in aphasia. Copyright © 2011 Elsevier Inc. All rights reserved.

Making software get along: integrating optical and mechanical design programs

NASA Astrophysics Data System (ADS)

Shackelford, Christie J.; Chinnock, Randal B.

2001-03-01

As modern optomechanical engineers, we have the good fortune of having very sophisticated software programs available to us. The current optical design, mechanical design, industrial design, and CAM programs are very powerful tools with some very desirable features. However, no one program can do everything necessary to complete an entire optomechanical system design. Each program has a unique set of features and benefits, and typically two or mo re will be used during the product development process. At a minimum, an optical design program and a mechanical CAD package will be employed. As we strive for efficient, cost-effective, and rapid progress in our development projects, we must use these programs to their full advantage, while keeping redundant tasks to a minimum. Together, these programs offer the promise of a `seamless' flow of data from concept all the way to the download of part designs directly to the machine shop for fabrication. In reality, transferring data from one software package to the next is often frustrating. Overcoming these problems takes some know-how, a bit of creativity, and a lot of persistence. This paper describes a complex optomechanical development effort in which a variety of software tools were used from the concept stage to prototyping. It will describe what software was used for each major design task, how we learned to use them together to best advantage, and how we overcame the frustrations of software that didn't get along.

Phenotypic and genetic features of enteropathogenic Escherichia coli isolates from diarrheal children in the Ribeirão Preto metropolitan area, São Paulo State, Brazil.

PubMed

Pitondo-Silva, André; Nakazato, Gerson; Falcão, Juliana P; Irino, Kinue; Martinez, Roberto; Darini, Ana Lúcia C; Hernandes, Rodrigo Tavanelli

2015-02-01

This study was designed to characterize a collection of 60 enteropathogenic Escherichia coli (EPEC) isolates from diarrheic feces of patients in the Ribeirão Preto metropolitan area regarding different phenotypic and molecular features. We examined antibiotic resistance profiles, occurrence of virulence factors-encoding genes, intimin subtypes and the correlation of serotypes among typical (tEPEC) and atypical (aEPEC) EPEC isolates. The results demonstrated that atypical EPEC was more heterogeneous than typical EPEC concerning the characteristics investigated and 45.2% do not belong to classical EPEC serogroups. Intimin subtype β was the most frequent among the EPEC isolates (46.7%), being detected in both tEPEC and aEPEC. The majority of aEPEC isolates presented localized adherence-like (LAL) pattern to HEp-2 cells, although aEPEC isolates displaying diffuse adherence (DA) or non-adherent were also detected. High prevalence of antimicrobial resistance was found for ampicillin, cephalothin, sulfonamide and tetracycline. In general, tEPEC isolates were more resistant to the antimicrobials tested than aEPEC isolates. © 2014 APMIS. Published by John Wiley & Sons Ltd.

Successful treatment of suspected organizing pneumonia in a patient without typical imaging and pathological characteristic: A case report.

PubMed

Ailing, Liu; Ning, Xu; Tao, Qu; Aijun, Li

2017-01-01

Organizing pneumonia (OP) is a clinicopathological entity characterized by granulation tissue plugs in the lumen of small airways, alveolar ducts, and alveoli. Diagnosis of OP needs the combination of clinical features, imaging and pathology. But it occurs often that there are no typical pathological features to support the diagnosis, which poses a challenge for clinicians' diagnosis and treatment. We diagnosed a case of OP without typical imaging and pathological characteristic and treated successfully. Finally we confirmed the pathological diagnosis. Not every OP case is supported by pathological evidence and typical imaging changes. It is important for us to judge and decide the diagnosis according to clinical experience.

Scaling of Performance in Liquid Propellant Rocket Engine Combustors

NASA Technical Reports Server (NTRS)

Hulka, James R.

2007-01-01

This paper discusses scaling of combustion and combustion performance in liquid propellant rocket engine combustion devices. In development of new combustors, comparisons are often made between predicted performance in a new combustor and measured performance in another combustor with different geometric and thermodynamic characteristics. Without careful interpretation of some key features, the comparison can be misinterpreted and erroneous information used in the design of the new device. This paper provides a review of this performance comparison, including a brief review of the initial liquid rocket scaling research conducted during the 1950s and 1960s, a review of the typical performance losses encountered and how they scale, a description of the typical scaling procedures used in development programs today, and finally a review of several historical development programs to see what insight they can bring to the questions at hand.

Scaling of Performance in Liquid Propellant Rocket Engine Combustion Devices

NASA Technical Reports Server (NTRS)

Hulka, James R.

2008-01-01

This paper discusses scaling of combustion and combustion performance in liquid propellant rocket engine combustion devices. In development of new combustors, comparisons are often made between predicted performance in a new combustor and measured performance in another combustor with different geometric and thermodynamic characteristics. Without careful interpretation of some key features, the comparison can be misinterpreted and erroneous information used in the design of the new device. This paper provides a review of this performance comparison, including a brief review of the initial liquid rocket scaling research conducted during the 1950s and 1960s, a review of the typical performance losses encountered and how they scale, a description of the typical scaling procedures used in development programs today, and finally a review of several historical development programs to see what insight they can bring to the questions at hand.

In Search of Commonalities: Some Linguistic and Rhetorical Features of Business Reports as a Genre

ERIC Educational Resources Information Center

Yeung, Lorrita

2007-01-01

The present study analyzes 22 authentic business reports in an attempt to identify textual features that are typical of business reports as a genre. The analysis shows that there are certain characteristics which distinguish business reports from other related genres such as scientific reports, of which RAs are a typical example. There are also…

Design Report Final - CUB Inc.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armijo, Kenneth Miguel; Monda, Mark J.; Brunson, Gregory Paul

CUB (Critical Utility Base), Fig. 1.0, are individual portable energy and utility units utilizing renewable energy technologies integrated with high efficient conventional components to provide electricity, battery storage, heat, potable water, waste water treatment, cooling, liquid fuels, to name some of the primary utilities. Typically, these units were designed to provide power / utilities to any remote location or facility like forward operating bases, disaster relief centers, and Native American communities or to energize African villages. Although some CUB models have already been designed to date, the main unit, the CUB-E (electricity), lacks a critical component included in its design.more » It is the integral portion that automates solar electric panel racking deployment and retraction. This racking system will enable the CUB-E to rapidly deploy its utility within minutes, a feature not available in any form currently on the market.« less

Aerodynamic design of electric and hybrid vehicles: A guidebook

NASA Technical Reports Server (NTRS)

Kurtz, D. W.

1980-01-01

A typical present-day subcompact electric hybrid vehicle (EHV), operating on an SAE J227a D driving cycle, consumes up to 35% of its road energy requirement overcoming aerodynamic resistance. The application of an integrated system design approach, where drag reduction is an important design parameter, can increase the cycle range by more than 15%. This guidebook highlights a logic strategy for including aerodynamic drag reduction in the design of electric and hybrid vehicles to the degree appropriate to the mission requirements. Backup information and procedures are included in order to implement the strategy. Elements of the procedure are based on extensive wind tunnel tests involving generic subscale models and full-scale prototype EHVs. The user need not have any previous aerodynamic background. By necessity, the procedure utilizes many generic approximations and assumptions resulting in various levels of uncertainty. Dealing with these uncertainties, however, is a key feature of the strategy.

A minimal length rigid helical peptide motif allows rational design of modular surfactants

NASA Astrophysics Data System (ADS)

Mondal, Sudipta; Varenik, Maxim; Bloch, Daniel Nir; Atsmon-Raz, Yoav; Jacoby, Guy; Adler-Abramovich, Lihi; Shimon, Linda J. W.; Beck, Roy; Miller, Yifat; Regev, Oren; Gazit, Ehud

2017-01-01

Extensive work has been invested in the design of bio-inspired peptide emulsifiers. Yet, none of the formulated surfactants were based on the utilization of the robust conformation and self-assembly tendencies presented by the hydrophobins, which exhibited highest surface activity among all known proteins. Here we show that a minimalist design scheme could be employed to fabricate rigid helical peptides to mimic the rigid conformation and the helical amphipathic organization. These designer building blocks, containing natural non-coded α-aminoisobutyric acid (Aib), form superhelical assemblies as confirmed by crystallography and microscopy. The peptide sequence is amenable to structural modularity and provides the highest stable emulsions reported so far for peptide and protein emulsifiers. Moreover, we establish the ability of short peptides to perform the dual functions of emulsifiers and thickeners, a feature that typically requires synergistic effects of surfactants and polysaccharides. This work provides a different paradigm for the molecular engineering of bioemulsifiers.

The HDF Product Designer - Interoperability in the First Mile

NASA Astrophysics Data System (ADS)

Lee, H.; Jelenak, A.; Habermann, T.

2014-12-01

Interoperable data have been a long-time goal in many scientific communities. The recent growth in analysis, visualization and mash-up applications that expect data stored in a standardized manner has brought the interoperability issue to the fore. On the other hand, producing interoperable data is often regarded as a sideline task in a typical research team for which resources are not readily available. The HDF Group is developing a software tool aimed at lessening the burden of creating data in standards-compliant, interoperable HDF5 files. The tool, named HDF Product Designer, lowers the threshold needed to design such files by providing a user interface that combines the rich HDF5 feature set with applicable metadata conventions. Users can quickly devise new HDF5 files while at the same time seamlessly incorporating the latest best practices and conventions from their community. That is what the term interoperability in the first mile means: enabling generation of interoperable data in HDF5 files from the onset of their production. The tool also incorporates collaborative features, allowing team approach in the file design, as well as easy transfer of best practices as they are being developed. The current state of the tool and the plans for future development will be presented. Constructive input from interested parties is always welcome.

Experimental Study of a Hot Structure for a Reentry Vehicle

NASA Technical Reports Server (NTRS)

Pride, Richard A.; Royster, Dick M.; Helms, Bobbie F.

1960-01-01

A large structural model of a reentry vehicle has been built incorporating design concepts applicable to a radiation-cooled vehicle. Thermal-stress alleviating features of the model are discussed. Environmental tests on the model include approximately 100 cycles of loading at room temperature and 33 cycles of combined loading and-heating up to temperatures of 1,6000 F. Measured temperatures are shown for typical parts of the model. Comparisons are made between experimental and calculated deflections and strains. The structure successfully survived the heating and loading environments.

Predicting the performance of fingerprint similarity searching.

PubMed

Vogt, Martin; Bajorath, Jürgen

2011-01-01

Fingerprints are bit string representations of molecular structure that typically encode structural fragments, topological features, or pharmacophore patterns. Various fingerprint designs are utilized in virtual screening and their search performance essentially depends on three parameters: the nature of the fingerprint, the active compounds serving as reference molecules, and the composition of the screening database. It is of considerable interest and practical relevance to predict the performance of fingerprint similarity searching. A quantitative assessment of the potential that a fingerprint search might successfully retrieve active compounds, if available in the screening database, would substantially help to select the type of fingerprint most suitable for a given search problem. The method presented herein utilizes concepts from information theory to relate the fingerprint feature distributions of reference compounds to screening libraries. If these feature distributions do not sufficiently differ, active database compounds that are similar to reference molecules cannot be retrieved because they disappear in the "background." By quantifying the difference in feature distribution using the Kullback-Leibler divergence and relating the divergence to compound recovery rates obtained for different benchmark classes, fingerprint search performance can be quantitatively predicted.

Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 1 - guideword applicability and method description.

PubMed

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-12-15

Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design.

Feature Inference Learning and Eyetracking

ERIC Educational Resources Information Center

Rehder, Bob; Colner, Robert M.; Hoffman, Aaron B.

2009-01-01

Besides traditional supervised classification learning, people can learn categories by inferring the missing features of category members. It has been proposed that feature inference learning promotes learning a category's internal structure (e.g., its typical features and interfeature correlations) whereas classification promotes the learning of…

ICT Solutions for Highly-Customized Water Demand Management Strategies

NASA Astrophysics Data System (ADS)

Giuliani, M.; Cominola, A.; Castelletti, A.; Fraternali, P.; Guardiola, J.; Barba, J.; Pulido-Velazquez, M.; Rizzoli, A. E.

2016-12-01

The recent deployment of smart metering networks is opening new opportunities for advancing the design of residential water demand management strategies (WDMS) relying on improved understanding of water consumers' behaviors. Recent applications showed that retrieving information on users' consumption behaviors, along with their explanatory and/or causal factors, is key to spot potential areas where targeting water saving efforts, and to design user-tailored WDMS. In this study, we explore the potential of ICT-based solutions in supporting the design and implementation of highly customized WDMS. On one side, the collection of consumption data at high spatial and temporal resolutions requires big data analytics and machine learning techniques to extract typical consumption features from the metered population of water users. On the other side, ICT solutions and gamifications can be used as effective means for facilitating both users' engagement and the collection of socio-psychographic users' information. This latter allows interpreting and improving the extracted profiles, ultimately supporting the customization of WDMS, such as awareness campaigns or personalized recommendations. Our approach is implemented in the SmartH2O platform and demonstrated in a pilot application in Valencia, Spain. Results show how the analysis of the smart metered consumption data, combined with the information retrieved from an ICT gamified web user portal, successfully identify the typical consumption profiles of the metered users and supports the design of alternative WDMS targeting the different users' profiles.

Performance Testing of Jefferson Lab 12 GeV Helium Screw Compressors

DOE PAGES

Knudsen, P.; Ganni, V.; Dixon, K.; ...

2015-08-10

Oil injected screw compressors have essentially superseded all other types of compressors in modern helium refrigeration systems due to their large displacement capacity, reliability, minimal vibration, and capability of handling helium's high heat of compression. At the present state of compressor system designs for helium refrigeration systems, typically two-thirds of the lost input power is due to the compression system. It is important to understand the isothermal and volumetric efficiencies of these machines to help properly design the compression system to match the refrigeration process. It is also important to identify those primary compressor skid exergetic loss mechanisms which maymore » be reduced, thereby offering the possibility of significantly reducing the input power to helium refrigeration processes which are extremely energy intensive. This paper summarizes the results collected during the commissioning of the new compressor system for Jefferson Lab's (JLab's) 12 GeV upgrade. The compressor skid packages were designed by JLab and built to print by industry. They incorporate a number of modifications not typical of helium screw compressor packages and most importantly allow a very wide range of operation so that JLab's patented Floating Pressure Process can be fully utilized. This paper also summarizes key features of the skid design that allow this process and facilitate the maintenance and reliability of these helium compressor systems.« less

Performance Testing of Jefferson Lab 12 GeV Helium Screw Compressors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knudsen, P.; Ganni, V.; Dixon, K.

Oil injected screw compressors have essentially superseded all other types of compressors in modern helium refrigeration systems due to their large displacement capacity, reliability, minimal vibration, and capability of handling helium's high heat of compression. At the present state of compressor system designs for helium refrigeration systems, typically two-thirds of the lost input power is due to the compression system. It is important to understand the isothermal and volumetric efficiencies of these machines to help properly design the compression system to match the refrigeration process. It is also important to identify those primary compressor skid exergetic loss mechanisms which maymore » be reduced, thereby offering the possibility of significantly reducing the input power to helium refrigeration processes which are extremely energy intensive. This paper summarizes the results collected during the commissioning of the new compressor system for Jefferson Lab's (JLab's) 12 GeV upgrade. The compressor skid packages were designed by JLab and built to print by industry. They incorporate a number of modifications not typical of helium screw compressor packages and most importantly allow a very wide range of operation so that JLab's patented Floating Pressure Process can be fully utilized. This paper also summarizes key features of the skid design that allow this process and facilitate the maintenance and reliability of these helium compressor systems.« less

The Advanced Light Source Elliptically Polarizing Undulator

NASA Astrophysics Data System (ADS)

Marks, Steve; Cortopassi, Christopher; Devries, Jan; Hoyer, Egon; Leinbach, Robert; Minamihara, Yoshi; Padmore, Howard; Pipersky, Paul; Plate, Dave; Schlueter, Ross; Young, Anthony

1997-05-01

An elliptically polarizing undulator for the Advanced Light Source has been designed and is currently under construction. The magnetic design is a four quadrant pure permanent magnet structure featuring moveable magnets to correct phase errors and on axis field integrals. The device is designed with a 5.0 cm period and will produce variably polarized light of any ellipticity, including pure circular and linear. The spectral range at 1.9 GeV for typical elliptical polarization with a degree of circular polarization greater than 0.8 will be from 100 eV to 1500 eV, using the third and fifth spectral harmonics. The device will be switchabe between left and right circular modes at a frequency of up to 0.1 Hz. The 1.95 m long overall length will allow two such devices in a single ALS straight sector.

An 'inflammatory' variant of solar purpura: a simulant of leukocytoclastic vasculitis and neutrophilic dermatoses.

PubMed

Wood, Benjamin A; LeBoit, Philip E

2013-08-01

To study the clinical and pathological features of cases of apparent solar purpura, with attention to the recently described phenomenon of inflammatory changes within otherwise typical lesions. We studied 95 cases diagnosed as solar purpura and identified 10 cases (10.5%) in which significant neutrophilic inflammation was present, potentially simulating a leukocytoclastic vasculitis or neutrophilic dermatosis. An additional three cases were identified in subsequent routine practice. The clinical features, including follow-up for subsequent development of vasculitis and histological features were studied. In all cases the histological features were typical of solar purpura, with the exception of inflammatory changes, typically associated with clefting of elastotic stroma. Clinical follow-up information was available for all patients and none developed subsequent evidence of a cutaneous or systemic vasculitis or neutrophilic dermatosis. Inflammatory changes appear to be more frequent in solar purpura than is generally recognised. Awareness of this histological variation and correlation with the clinical findings and evolution is important in avoiding misdiagnosis.

The molecular mechanisms on glomangiopericytoma invasion

PubMed Central

2013-01-01

Purpose To observed the imaging and pathological features of the glomangiopericytoma. Experimental design In this paper we report a typical case of glomangiopericytoma arising in the skull base area and summarize the clinical manifestations, imaging and pathological features of such diseases. Results Immunohistochemical staining confirmed the tumor cells were strongly positive to Vim, SMA, MSA and negative to CD31, CD34. Partial cells were positive to FVIII. The imaging can’t confirm the diagnosis but indicate the the tumor has intact envelope.The cells in the tumor envelope is positive to Vim and negative SMA and FVIII. These findings were compatible with glomangiopericytoma and the cells in the tumor envelope is not glomangiopericytoma cells. Conclusion In view of the clinical and pathological features of the glomangiopericytoma, we believe that the surgery is the best treatment so far and the tumor can be resected completely. The above results can be preliminary reason to explain the low recurrence of such diseases. PMID:24074285

Data Encoding using Periodic Nano-Optical Features

NASA Astrophysics Data System (ADS)

Vosoogh-Grayli, Siamack

Successful trials have been made through a designed algorithm to quantize, compress and optically encode unsigned 8 bit integer values in the form of images using Nano optical features. The periodicity of the Nano-scale features (Nano-gratings) have been designed and investigated both theoretically and experimentally to create distinct states of variation (three on states and one off state). The use of easy to manufacture and machine readable encoded data in secured authentication media has been employed previously in bar-codes for bi-state (binary) models and in color barcodes for multiple state models. This work has focused on implementing 4 states of variation for unit information through periodic Nano-optical structures that separate an incident wavelength into distinct colors (variation states) in order to create an encoding system. Compared to barcodes and magnetic stripes in secured finite length storage media the proposed system encodes and stores more data. The benefits of multiple states of variation in an encoding unit are 1) increased numerically representable range 2) increased storage density and 3) decreased number of typical set elements for any ergodic or semi-ergodic source that emits these encoding units. A thorough investigation has targeted the effects of the use of multi-varied state Nano-optical features on data storage density and consequent data transmission rates. The results show that use of Nano-optical features for encoding data yields a data storage density of circa 800 Kbits/in2 via the implementation of commercially available high resolution flatbed scanner systems for readout. Such storage density is far greater than commercial finite length secured storage media such as Barcode family with maximum practical density of 1kbits/in2 and highest density magnetic stripe cards with maximum density circa 3 Kbits/in2. The numerically representable range of the proposed encoding unit for 4 states of variation is [0 255]. The number of typical set elements for an ergodic source emitting the optical encoding units compared to a bi-state encoding unit (bit) shows a 36 orders of magnitude decrease for the error probability interval of [0 0.01]. The algorithms for the proposed encoding system have been implemented in MATLAB and the Nano-optical structures have been fabricated using Electron Beam Lithography on optical medium.

AlphaSpace: Fragment-Centric Topographical Mapping To Target Protein–Protein Interaction Interfaces

PubMed Central

2016-01-01

Inhibition of protein–protein interactions (PPIs) is emerging as a promising therapeutic strategy despite the difficulty in targeting such interfaces with drug-like small molecules. PPIs generally feature large and flat binding surfaces as compared to typical drug targets. These features pose a challenge for structural characterization of the surface using geometry-based pocket-detection methods. An attractive mapping strategy—that builds on the principles of fragment-based drug discovery (FBDD)—is to detect the fragment-centric modularity at the protein surface and then characterize the large PPI interface as a set of localized, fragment-targetable interaction regions. Here, we introduce AlphaSpace, a computational analysis tool designed for fragment-centric topographical mapping (FCTM) of PPI interfaces. Our approach uses the alpha sphere construct, a geometric feature of a protein’s Voronoi diagram, to map out concave interaction space at the protein surface. We introduce two new features—alpha-atom and alpha-space—and the concept of the alpha-atom/alpha-space pair to rank pockets for fragment-targetability and to facilitate the evaluation of pocket/fragment complementarity. The resulting high-resolution interfacial map of targetable pocket space can be used to guide the rational design and optimization of small molecule or biomimetic PPI inhibitors. PMID:26225450

Sparsity-aware tight frame learning with adaptive subspace recognition for multiple fault diagnosis

NASA Astrophysics Data System (ADS)

Zhang, Han; Chen, Xuefeng; Du, Zhaohui; Yang, Boyuan

2017-09-01

It is a challenging problem to design excellent dictionaries to sparsely represent diverse fault information and simultaneously discriminate different fault sources. Therefore, this paper describes and analyzes a novel multiple feature recognition framework which incorporates the tight frame learning technique with an adaptive subspace recognition strategy. The proposed framework consists of four stages. Firstly, by introducing the tight frame constraint into the popular dictionary learning model, the proposed tight frame learning model could be formulated as a nonconvex optimization problem which can be solved by alternatively implementing hard thresholding operation and singular value decomposition. Secondly, the noises are effectively eliminated through transform sparse coding techniques. Thirdly, the denoised signal is decoupled into discriminative feature subspaces by each tight frame filter. Finally, in guidance of elaborately designed fault related sensitive indexes, latent fault feature subspaces can be adaptively recognized and multiple faults are diagnosed simultaneously. Extensive numerical experiments are sequently implemented to investigate the sparsifying capability of the learned tight frame as well as its comprehensive denoising performance. Most importantly, the feasibility and superiority of the proposed framework is verified through performing multiple fault diagnosis of motor bearings. Compared with the state-of-the-art fault detection techniques, some important advantages have been observed: firstly, the proposed framework incorporates the physical prior with the data-driven strategy and naturally multiple fault feature with similar oscillation morphology can be adaptively decoupled. Secondly, the tight frame dictionary directly learned from the noisy observation can significantly promote the sparsity of fault features compared to analytical tight frames. Thirdly, a satisfactory complete signal space description property is guaranteed and thus weak feature leakage problem is avoided compared to typical learning methods.

Image Reconstruction from Under sampled Fourier Data Using the Polynomial Annihilation Transform

DOE Office of Scientific and Technical Information (OSTI.GOV)

Archibald, Richard K.; Gelb, Anne; Platte, Rodrigo

Fourier samples are collected in a variety of applications including magnetic resonance imaging and synthetic aperture radar. The data are typically under-sampled and noisy. In recent years, l 1 regularization has received considerable attention in designing image reconstruction algorithms from under-sampled and noisy Fourier data. The underlying image is assumed to have some sparsity features, that is, some measurable features of the image have sparse representation. The reconstruction algorithm is typically designed to solve a convex optimization problem, which consists of a fidelity term penalized by one or more l 1 regularization terms. The Split Bregman Algorithm provides a fastmore » explicit solution for the case when TV is used for the l1l1 regularization terms. Due to its numerical efficiency, it has been widely adopted for a variety of applications. A well known drawback in using TV as an l 1 regularization term is that the reconstructed image will tend to default to a piecewise constant image. This issue has been addressed in several ways. Recently, the polynomial annihilation edge detection method was used to generate a higher order sparsifying transform, and was coined the “polynomial annihilation (PA) transform.” This paper adapts the Split Bregman Algorithm for the case when the PA transform is used as the l 1 regularization term. In so doing, we achieve a more accurate image reconstruction method from under-sampled and noisy Fourier data. Our new method compares favorably to the TV Split Bregman Algorithm, as well as to the popular TGV combined with shearlet approach.« less

High-Lift Propeller System Configuration Selection for NASA's SCEPTOR Distributed Electric Propulsion Flight Demonstrator

NASA Technical Reports Server (NTRS)

Patterson, Michael D.; Derlaga, Joseph M.; Borer, Nicholas K.

2016-01-01

Although the primary function of propellers is typically to produce thrust, aircraft equipped with distributed electric propulsion (DEP) may utilize propellers whose main purpose is to act as a form of high-lift device. These \\high-lift propellers" can be placed upstream of wing such that, when the higher-velocity ow in the propellers' slipstreams interacts with the wing, the lift is increased. This technique is a main design feature of a new NASA advanced design project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR). The goal of the SCEPTOR project is design, build, and y a DEP aircraft to demonstrate that such an aircraft can be much more ecient than conventional designs. This paper provides details into the high-lift propeller system con guration selection for the SCEPTOR ight demonstrator. The methods used in the high-lift propeller system conceptual design and the tradeo s considered in selecting the number of propellers are discussed.

The Design of Case Products’ Shape Form Information Database Based on NURBS Surface

NASA Astrophysics Data System (ADS)

Liu, Xing; Liu, Guo-zhong; Xu, Nuo-qi; Zhang, Wei-she

2017-07-01

In order to improve the computer design of product shape design,applying the Non-uniform Rational B-splines(NURBS) of curves and surfaces surface to the representation of the product shape helps designers to design the product effectively.On the basis of the typical product image contour extraction and using Pro/Engineer(Pro/E) to extract the geometric feature of scanning mold,in order to structure the information data base system of value point,control point and node vector parameter information,this paper put forward a unified expression method of using NURBS curves and surfaces to describe products’ geometric shape and using matrix laboratory(MATLAB) to simulate when products have the same or similar function.A case study of electric vehicle’s front cover illustrates the access process of geometric shape information of case product in this paper.This method can not only greatly reduce the capacity of information debate,but also improve the effectiveness of computer aided geometric innovation modeling.

On the benefit of high resolution and low aberrations for in-die mask registration metrology

NASA Astrophysics Data System (ADS)

Beyer, Dirk; Seidel, Dirk; Heisig, Sven; Steinert, Steffen; Töpfer, Susanne; Scherübl, Thomas; Hetzler, Jochen

2014-10-01

With the introduction of complex lithography schemes like double and multi - patterning and new design principles like gridded designs with cut masks the requirements for mask to mask overlay have increased dramatically. Still, there are some good news too for the mask industry since more mask are needed and qualified. Although always confronted with throughput demands, latest writing tool developments are able to keep pace with ever increasing pattern placement specs not only for global signatures but for in-die features within the active area. Placement specs less than 3nm (max. 3 Sigma) are expected and needed in all cases in order to keep the mask contribution to the overall overlay budget at an accepted level. The qualification of these masks relies on high precision metrology tools which have to fulfill stringent metrology as well as resolution constrains at the same time. Furthermore, multi-patterning and gridded designs with pinhole type cut masks are drivers for a paradigm shift in registration metrology from classical registration crosses to in-die registration metrology on production features. These requirements result in several challenges for registration metrology tools. The resolution of the system must be sufficiently high to resolve small production features. At the same time tighter repeatability is required. Furthermore, tool induced shift (TIS) limit the accuracy of in-die measurements. This paper discusses and demonstrates the importance of low illumination wavelength together with low aberrations for best contrast imaging for in-die registration metrology. Typical effects like tool induced shift are analyzed and evaluated using the ZEISS PROVE® registration metrology tool. Additionally, we will address performance gains when going to higher resolution. The direct impact on repeatability for small features by registration measurements will be discussed as well.

Propulsion Design With Freeform Fabrication (PDFF)

NASA Technical Reports Server (NTRS)

Barnes, Daudi; McKinnon, James; Priem, Richard

2010-01-01

The nation is challenged to decrease the cost and schedule to develop new space transportation propulsion systems for commercial, scientific, and military purposes. Better design criteria and manufacturing techniques for small thrusters are needed to meet current applications in missile defense, space, and satellite propulsion. The requirements of these systems present size, performance, and environmental demands on these thrusters that have posed significant challenges to the current designers and manufacturers. Designers are limited by manufacturing processes, which are complex, costly, and time consuming, and ultimately limited in their capabilities. The PDFF innovation vastly extends the design opportunities of rocket engine components and systems by making use of the unique manufacturing freedom of solid freeform rapid prototype manufacturing technology combined with the benefits of ceramic materials. The unique features of PDFF are developing and implementing a design methodology that uses solid freeform fabrication (SFF) techniques to make propulsion components with significantly improved performance, thermal management, power density, and stability, while reducing development and production costs. PDFF extends the design process envelope beyond conventional constraints by leveraging the key feature of the SFF technique with the capability to form objects with nearly any geometric complexity without the need for elaborate machine setup. The marriage of SFF technology to propulsion components allows an evolution of design practice to harmonize material properties with functional design efficiency. Reduced density of materials when coupled with the capability to honeycomb structure used in the injector will have significant impact on overall mass reduction. Typical thrusters in use for attitude control have 60 90 percent of its mass in the valve and injector, which is typically made from titanium. The combination of material and structure envisioned for use in an SFF thruster design could reduce thruster weight by a factor of two or more. The thrust-to-weight ratios for such designs can achieve 1,000:1 or more, depending on chamber pressure. The potential exists for continued development in materials, size, speed, accuracy of SFF techniques, which can lead to speculative developments of PDFF processes such as fabrication of custom human interface devices like masks, chairs, and clothing, and advanced biomedical application to human organ reconstruction. Other potential applications are: higher fidelity lower cost test fixtures for probes and inspection, disposable thrusters, and ISRU (in situ resource utilization) for component production in space or on Lunar and Martian missions, and application for embedding MEMS (microelectromechanical systems) during construction process of form changing aerostructure/dynamic structures.

Abnormal semantic knowledge in a case of developmental amnesia.

PubMed

Blumenthal, Anna; Duke, Devin; Bowles, Ben; Gilboa, Asaf; Rosenbaum, R Shayna; Köhler, Stefan; McRae, Ken

2017-07-28

An important theory holds that semantic knowledge can develop independently of episodic memory. One strong source of evidence supporting this independence comes from the observation that individuals with early hippocampal damage leading to developmental amnesia generally perform normally on standard tests of semantic memory, despite their profound impairment in episodic memory. However, one aspect of semantic memory that has not been explored is conceptual structure. We built on the theoretically important distinction between intrinsic features of object concepts (e.g., shape, colour, parts) and extrinsic features (e.g., how something is used, where it is typically located). The accrual of extrinsic feature knowledge that is important for concepts such as chair or spoon may depend on binding mechanisms in the hippocampus. We tested HC, an individual with developmental amnesia due to a well-characterized lesion of the hippocampus, on her ability to generate semantic features for object concepts. HC generated fewer extrinsic features than controls, but a similar number of intrinsic features than controls. We also tested her on typicality ratings. Her typicality ratings were abnormal for nonliving things (which more strongly depend on extrinsic features), but normal for living things (which more strongly depend on intrinsic features). In contrast, NB, who has MTL but not hippocampal damage due to surgery, showed no impairments in either task. These results suggest that episodic and semantic memory are not entirely independent, and that the hippocampus is important for learning some aspects of conceptual knowledge. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparison of l₁-Norm SVR and Sparse Coding Algorithms for Linear Regression.

PubMed

Zhang, Qingtian; Hu, Xiaolin; Zhang, Bo

2015-08-01

Support vector regression (SVR) is a popular function estimation technique based on Vapnik's concept of support vector machine. Among many variants, the l1-norm SVR is known to be good at selecting useful features when the features are redundant. Sparse coding (SC) is a technique widely used in many areas and a number of efficient algorithms are available. Both l1-norm SVR and SC can be used for linear regression. In this brief, the close connection between the l1-norm SVR and SC is revealed and some typical algorithms are compared for linear regression. The results show that the SC algorithms outperform the Newton linear programming algorithm, an efficient l1-norm SVR algorithm, in efficiency. The algorithms are then used to design the radial basis function (RBF) neural networks. Experiments on some benchmark data sets demonstrate the high efficiency of the SC algorithms. In particular, one of the SC algorithms, the orthogonal matching pursuit is two orders of magnitude faster than a well-known RBF network designing algorithm, the orthogonal least squares algorithm.

Is adermatoglyphia an additional feature of Kindler Syndrome?

PubMed

Almeida, Hiram Larangeira de; Goetze, Fernanda Mendes; Fong, Kenneth; Lai-Cheong, Joey; McGrath, John

2015-01-01

A typical feature of Kindler Syndrome is skin fragility; this condition in currently classified as a form of epidermolysis bullosa. We describe a rarely reported feature of two cases, one sporadic and one familial; both patients noticed acquired adermatoglyphia. The loss of dermatoglyphics could be an additional feature of this syndrome.

GENDER ROLE AND PERSONALITY DISORDERS

PubMed Central

Klonsky, E. David; Jane, J. Serrita; Turkheimer, Eric; Oltmanns, Thomas F.

2015-01-01

Many researchers have hypothesized relationships between personality disorders and gender role (i.e., masculinity and femininity). However, research has not addressed if people who are masculine or feminine more often meet the criteria for personality disorders. The present study examined whether college students (N = 665, 60% women) higher in masculinity or femininity more often exhibited features of the 10 DSM-IV personality disorders. Feminine men exhibited more features of all the personality disorders except antisocial. Dependent traits were associated with higher femininity and lower masculinity. Antisocial traits were associated with masculinity. Both men and women who typically behaved consistent with their gender had more narcissistic and histrionic features, whereas participants who typically behaved unlike their gender had more features of the Cluster A personality disorders. PMID:12489312

The effects of color cues on typically developing preschoolers' speed of locating a target line drawing: implications for augmentative and alternative communication display design.

PubMed

Thistle, Jennifer J; Wilkinson, Krista

2009-08-01

This research examined how the presence of color in relation to a target within an augmentative and alternative communication array influenced the speed with which typically developing preschoolers located a target line drawing. Fifteen children over the age of 4 years (from 4;2 [years;months] to 5;4) and 15 children under the age of 4 years (2;10-3;11) participated. Participants were asked to find a target line drawing of foods (e.g., banana and tomato) among an array of 12. The reaction time of locating the target was measured across 4 conditions in which the foreground color and the background color of the line drawing were manipulated. For all participants, line drawings featuring foreground color provided greater advantages in the speed of locating the target compared with drawings featuring only background color. Younger participants demonstrated faster reaction times when color was limited to the foreground. Clinicians should consider incorporating color in the foreground of the line drawing when constructing visual displays. Targets that contain only background color but no foreground color appear to have a negative effect on the speed with which younger children can locate a target. Further research is needed to determine the effects in children with disabilities.

Infiltrative cervical lesions causing symptomatic occipital neuralgia.

PubMed

Sierra-Hidalgo, F; Ruíz, J; Morales-Cartagena, A; Martínez-Salio, A; Serna, J de la; Hernández-Gallego, J

2011-10-01

Occipital neuralgia is a well-recognized cause of posterior head and neck pain that may associate mild sensory changes in the cutaneous distribution of the occipital nerves, lacking a recognizable local structural aetiology in most cases. Atypical clinical features or an abnormal neurological examination are alerts for a potential underlying cause of pain, although cases of clinically typical occipital neuralgia as isolated manifestation of lesions of the cervical spinal cord, cervical roots, or occipital nerves have been increasingly reported. We describe two cases (one with typical and another one with atypical clinical features) of occipital neuralgia secondary to paravertebral pyomyositis and vertebral relapse of multiple myeloma in patients with relevant medical history that aroused the possibility of an underlying structural lesion. We discuss the need for cranio-cervical magnetic resonance imaging in all patients with occipital neuralgia, even when typical clinical features are present and neurological examination is completely normal.

Vigil Network sites: A sample of data for permanent filing

USGS Publications Warehouse

Leopold, Luna Bergere; Emmett, William W.

1965-01-01

The Vigil Network consists of places where observations are made through time to record changes in landscape features over a long period. Resurveys will usually be made once each year or every few years and the period of observation, hopefully, will extend through and beyond the International Hydrological Decade.Vigil Network sites will usually be chosen to represent some typical feature of a given landscape. In the example shown here, the feature is a small ephemeral channel in a basin of moderate relief underlain by silty sandstone typical of the surrounding area. Vigil sites are not protected from man's influence and indeed may be selected because of the possible or portending cultural influences. In this respect they differ from the Bench Mark Network whose purpose is to make precise observations of hydrologic factors in areas uninfluenced by and protected from man's use.The factors which might be observed are many and varied. A few might be mentioned here, others are explained at length elsewhere (Miller and Leopold, 1963; Leopold, 1962). Streamchannel position, form, depth, and profile; vegetation in form of transects or quadrats; soil movement on slopes; rock movement on slopes or in channels. These and many more would yield valuable information on changes with time.To assure permanence of initial field observations, including reference points, bench marks, and cross sections, brief descriptions, maps, and initial data should be filed identically in designated repositories where the data will be made available for inspection by any interested scientist. It is recommended that the designation of two such locations where records of the type here attached will be filed be taken up by the Coordinating Council of the International Hydrological Decade. In designating such repositories it should be recognized that there is no need for elaborate indexing. The main requirement is merely the maintenance of a simple file where the data are stored and can be inspected or copied by any scientist. There need be no special provision for lending or reproduction services.The present document is an example showing what data, maps, and descriptions should be included in those permanent files at the two repositories. The material in these repositories should be sufficient to permit someone in the indefinite future to find and remeasure the same features described now. Thus the scientific value of the original surveys increases with time, - provided that the descriptions are sufficient to allow a person to find with assurance the original feature in the field.It must be visualized that a permanent repository must economize in space. Thus, as the example here shows, the filed material is not all of the original field notes but a summary, brief but descriptive.

Flow in a centrifugal fan impeller at off-design conditions

NASA Astrophysics Data System (ADS)

Wright, T.; Tzou, K. T. S.; Madhavan, S.

1984-06-01

A fully three-dimensional finite element analysis of inviscid, incompressible blade channel flow is the basis of the present study of both predicted and measured surface velocity and pressure distributions in the internal flow channels of a centrifugal fan impeller, for volume flow rates of 80-125 percent the design flow rate. The experimental results made extensive use of blade and sidewall surface pressure taps installed in a scale model of an airfoil-bladed centrifugal fan impeller. The results obtained illustrate the ability of both flow analyses to predict the dominant features of the impeller flow field, including peak blade surface velocities and adverse gradients at flows far from the design point. Insight is also gained into the limiting channel diffusion values for typical centrifugal cascade performance, together with the influence of viscous effects, as seen in deviations from ideal flow predictions.

Light sheet microscopy.

PubMed

Weber, Michael; Mickoleit, Michaela; Huisken, Jan

2014-01-01

This chapter introduces the concept of light sheet microscopy along with practical advice on how to design and build such an instrument. Selective plane illumination microscopy is presented as an alternative to confocal microscopy due to several superior features such as high-speed full-frame acquisition, minimal phototoxicity, and multiview sample rotation. Based on our experience over the last 10 years, we summarize the key concepts in light sheet microscopy, typical implementations, and successful applications. In particular, sample mounting for long time-lapse imaging and the resulting challenges in data processing are discussed in detail. © 2014 Elsevier Inc. All rights reserved.

Low-power SXGA active matrix OLED

NASA Astrophysics Data System (ADS)

Wacyk, Ihor; Prache, Olivier; Ghosh, Amal

2009-05-01

This paper presents the design and first evaluation of a full-color 1280×3×1024 pixel, active matrix organic light emitting diode (AMOLED) microdisplay that operates at a low power of 200mW under typical operating conditions of 35fL, and offers a precision 30-bit RGB digital interface in a compact size (0.78-inch diagonal active area). The new system architecture developed by eMagin for the SXGA microdisplay, based on a separate FPGA driver and AMOLED display chip, offers several benefits, including better power efficiency, cost-effectiveness, more features for improved performance, and increased system flexibility.

Results of acoustic testing of the JT8D-109 refan engines

NASA Technical Reports Server (NTRS)

Burdsall, E. A.; Brochu, F. P.; Scaramella, V. M.

1975-01-01

A JT8D engine was modified to reduce jet noise levels by 6-8 PNdB at takeoff power without increasing fan generated noise levels. Designated the JT8D-109, the modified engines featured a larger single stage fan, and acoustic treatment in the fan discharge ducts. Noise levels were measured on an outdoor test facility for eight engine/acoustic treatment configurations. Compared to the baseline JT8D, the fully treated JT8D-109 showed reductions of 6 PNdB at takeoff, and 11 PNdB at a typical approach power setting.

Automated benchmark generation based upon a specification language

NASA Technical Reports Server (NTRS)

Rajan, N.; Feteih, S. E.; Saito, J.

1984-01-01

The problem of validating and verifying digital flight control system (DFCS) software is addressed in this paper. A new specification language DIVERS is proposed, and is the keystone of the approach. This language consists of keywords where each keyword represents an element in the block diagram of a DFCS. DIVERS has a dictionary which contains all the keywords a DFCS designer might need. Translator programs convert the system specifications into an executable, high-level language program. The features of translators are discussed and are elucidated by examples. This language is used to describe a typical flight software module.

Construction of In-house Databases in a Corporation

NASA Astrophysics Data System (ADS)

Sano, Hikomaro

This report outlines “Repoir” (Report information retrieval) system of Toyota Central R & D Laboratories, Inc. as an example of in-house information retrieval system. The online system was designed to process in-house technical reports with the aid of a mainframe computer and has been in operation since 1979. Its features are multiple use of the information for technical and managerial purposes and simplicity in indexing and data input. The total number of descriptors, specially selected for the system, was minimized for ease of indexing. The report also describes the input items, processing flow and typical outputs in kanji letters.

UCTM2: An updated User friendly Configurable Trigger, scaler and delay Module for nuclear and particle physics

NASA Astrophysics Data System (ADS)

Bourrion, O.; Boyer, B.; Derome, L.; Pignol, G.

2016-06-01

We developed a highly integrated and versatile electronic module to equip small nuclear physics experiments and lab teaching classes: the User friendly Configurable Trigger, scaler and delay Module for nuclear and particle physics (UCTM). It is configurable through a Graphical User Interface (GUI) and provides a large number of possible trigger conditions without any Hardware Description Language (HDL) required knowledge. This new version significantly enhances the previous capabilities by providing two additional features: signal digitization and time measurements. The design, performances and a typical application are presented.

Loadcell supports for a dynamic force plate. [using piezoelectric tranducers and electromyography to study human gait

NASA Technical Reports Server (NTRS)

Keller, C. W.; Musil, L. M.; Hagy, J. L.

1975-01-01

An apparatus was developed to accurately measure components of force along three mutually perpendicular axes, torque, and the center of pressure imposed by the foot of a subject walking over its surface. The data obtained were used to supplement high-speed motion picture and electromyographic (EMG) data for in-depth studies of normal or abnormal human gait. Significant features of the design (in particular, the mechanisms used to support the loadcell transducers) are described. Results of the development program and typical data obtained with the device are presented and discussed.

Tempting food words activate eating simulations

PubMed Central

Papies, Esther K.

2013-01-01

This study shows that tempting food words activate simulations of eating the food, including simulations of the taste and texture of the food, simulations of eating situations, and simulations of hedonic enjoyment. In a feature listing task, participants generated features that are typically true of four tempting foods (e.g., chips) and four neutral foods (e.g., rice). The resulting features were coded as features of eating simulations if they referred to the taste, texture, and temperature of the food (e.g., “crunchy”; “sticky”), to situations of eating the food (e.g., “movie”; “good for Wok dishes”), and to the hedonic experience when eating the food (e.g., “tasty”). Based on the grounded cognition perspective, it was predicted that tempting foods are more likely to be represented in terms of actually eating them, so that participants would list more features referring to eating simulations for tempting than for neutral foods. Confirming this hypothesis, results showed that eating simulation features constituted 53% of the features for tempting food, and 26% of the features for neutral food. Visual features, in contrast, were mentioned more often for neutral foods (45%) than for tempting foods (19%). Exploratory analyses revealed that the proportion of eating simulation features for tempting foods was positively correlated with perceived attractiveness of the foods, and negatively with participants’ dieting concerns, suggesting that eating simulations may depend on individuals’ goals with regard to eating. These findings are discussed with regard to their implications for understanding the processes guiding eating behavior, and for interventions designed to reduce the consumption of attractive, unhealthy food. PMID:24298263

Learning a novel phonological contrast depends on interactions between individual differences and training paradigm design

PubMed Central

Perrachione, Tyler K.; Lee, Jiyeon; Ha, Louisa Y. Y.; Wong, Patrick C. M.

2011-01-01

Studies evaluating phonological contrast learning typically investigate either the predictiveness of specific pretraining aptitude measures or the efficacy of different instructional paradigms. However, little research considers how these factors interact—whether different students learn better from different types of instruction—and what the psychological basis for any interaction might be. The present study demonstrates that successfully learning a foreign-language phonological contrast for pitch depends on an interaction between individual differences in perceptual abilities and the design of the training paradigm. Training from stimuli with high acoustic-phonetic variability is generally thought to improve learning; however, we found high-variability training enhanced learning only for individuals with strong perceptual abilities. Learners with weaker perceptual abilities were actually impaired by high-variability training relative to a low-variability condition. A second experiment assessing variations on the high-variability training design determined that the property of this learning environment most detrimental to perceptually weak learners is the amount of trial-by-trial variability. Learners’ perceptual limitations can thus override the benefits of high-variability training where trial-by-trial variability in other irrelevant acoustic-phonetic features obfuscates access to the target feature. These results demonstrate the importance of considering individual differences in pretraining aptitudes when evaluating the efficacy of any speech training paradigm. PMID:21786912

Is adermatoglyphia an additional feature of Kindler Syndrome?*

PubMed Central

de Almeida Jr, Hiram Larangeira; Goetze, Fernanda Mendes; Fong, Kenneth; Lai-Cheong, Joey; McGrath, John

2015-01-01

A typical feature of Kindler Syndrome is skin fragility; this condition in currently classified as a form of epidermolysis bullosa. We describe a rarely reported feature of two cases, one sporadic and one familial; both patients noticed acquired adermatoglyphia. The loss of dermatoglyphics could be an additional feature of this syndrome. PMID:26375235

The solar maximum satellite capture cell: Impact features and orbital debris and micrometeoritic projectile materials

NASA Technical Reports Server (NTRS)

Mckay, D. S.; Rietmeijer, F. J. M.; Schramm, L. S.; Barrett, R. A.; Zook, H. A.; Blanford, G. E.

1986-01-01

The physical properties of impact features observed in the Solar Max main electronics box (MEB) thermal blanket generally suggest an origin by hypervelocity impact. The chemistry of micrometeorite material suggests that a wide variety of projectile materials have survived impact with retention of varying degrees of pristinity. Impact features that contain only spacecraft paint particles are on average smaller than impact features caused by micrometeorite impacts. In case both types of materials co-occur, it is belevied that the impact feature, generally a penetration hole, was caused by a micrometeorite projectile. The typically smaller paint particles were able to penetrate though the hole in the first layer and deposit in the spray pattern on the second layer. It is suggested that paint particles have arrived with a wide range of velocities relative to the Solar Max satellite. Orbiting paint particles are an important fraction of materials in the near-Earth environment. In general, the data from the Solar Max studies are a good calibration for the design of capture cells to be flown in space and on board Space Station. The data also suggest that development of multiple layer capture cells in which the projectile may retain a large degree of pristinity is a feasible goal.

Heat transfer technology for internal passages of air-cooled blades for heavy-duty gas turbines.

PubMed

Weigand, B; Semmler, K; von Wolfersdorf, J

2001-05-01

The present review paper, although far from being complete, aims to give an overview about the present state of the art in the field of heat transfer technology for internal cooling of gas turbine blades. After showing some typical modern cooled blades, the different methods to enhance heat transfer in the internal passages of air-cooled blades are discussed. The complicated flows occurring in bends are described in detail, because of their increasing importance for modern cooling designs. A short review about testing of cooling design elements is given, showing the interaction of the different cooling features as well. The special focus of the present review has been put on the cooling of blades for heavy-duty gas turbines, which show several differences compared to aero-engine blades.

Xeroderma pigmentosum is a definite cause of Huntington's disease-like syndrome.

PubMed

Garcia-Moreno, Hector; Fassihi, Hiva; Sarkany, Robert P E; Phukan, Julie; Warner, Thomas; Lehmann, Alan R; Giunti, Paola

2018-01-01

Xeroderma pigmentosum is characterized by cutaneous, ophthalmological, and neurological features. Although it is typical of childhood, late presentations can mimic different neurodegenerative conditions. We report two families presenting as Huntington's disease-like syndromes. The first case (group G) presented with neuropsychiatric features, cognitive decline and chorea. Typical lentigines were only noticed after the neurological disease started. The second case (group B) presented adult-onset chorea and neuropsychiatric symptoms after an aggressive ocular melanoma. Xeroderma pigmentosum can manifest as a Huntington's Disease-like syndrome. Classic dermatological and oncological features have to be investigated in choreic patients with negative genetic tests for Huntington's disease-like phenotypes.

Catatonia in Psychotic Patients: Clinical Features and Treatment Response

PubMed Central

England, Mary L.; Öngür, Dost; Konopaske, Glenn T.; Karmacharya, Rakesh

2012-01-01

We report clinical features and treatment response in 25 patients with catatonia admitted to an inpatient psychiatric unit specializing in psychotic disorders. ECT, benzodiazepines, and clozapine had beneficial effects on catatonic features, while typical antipsychotics resulted in clinical worsening. PMID:21677256

A Role for Epigenetic Mechanisms in Organ-Specific Breast Cancer Metastasis

DTIC Science & Technology

2010-05-01

of origin. The neovasculature of tumors is typically leaky (Carmeliet and Jain, 2000; Rafii et al., 2003), a feature that would facilitate not only...and therapy selection in esophageal cancer. Cancer Cell 13, 441- 453. Rafii , S., Avecilla, S.T., and Jin, D.K. (2003). Tumor vasculature address book...origin. The neovasculature of tumors is typically leaky (Carmeliet and Jain, 2000; Rafii et al., 2003), a feature that would facilitate not only the

CT of hepatic schistosomiasis mansoni

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fataar, S.; Bassiony, H.; Satyanath, S.

1985-07-01

Schistosomal periportal fibrosis produced a typical pattern on computed tomography in five patients. Low-density periportal tissue, present throughout the liver, enhanced strongly after the administration of contrast medium. While rounded in cross section, the thickened periportal tissue produced linear and branching patterns when imaged in longitudinal section. In all cases, the sonographic features were typical of schistosomal periportal fibrosis. A lack of awareness of the distinctive features of periportal fibrosis may result in a mistaken diagnosis of hepatic metastases.

Small Microprocessor for ASIC or FPGA Implementation

NASA Technical Reports Server (NTRS)

Kleyner, Igor; Katz, Richard; Blair-Smith, Hugh

2011-01-01

A small microprocessor, suitable for use in applications in which high reliability is required, was designed to be implemented in either an application-specific integrated circuit (ASIC) or a field-programmable gate array (FPGA). The design is based on commercial microprocessor architecture, making it possible to use available software development tools and thereby to implement the microprocessor at relatively low cost. The design features enhancements, including trapping during execution of illegal instructions. The internal structure of the design yields relatively high performance, with a significant decrease, relative to other microprocessors that perform the same functions, in the number of microcycles needed to execute macroinstructions. The problem meant to be solved in designing this microprocessor was to provide a modest level of computational capability in a general-purpose processor while adding as little as possible to the power demand, size, and weight of a system into which the microprocessor would be incorporated. As designed, this microprocessor consumes very little power and occupies only a small portion of a typical modern ASIC or FPGA. The microprocessor operates at a rate of about 4 million instructions per second with clock frequency of 20 MHz.

43 CFR 8223.0-5 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... threatened or endangered plant or animal species; (4) A typical representation of common geologic, soil, or water features; or (5) Outstanding or unusual geologic, soil, or water features. (b) [Reserved] ...

43 CFR 8223.0-5 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... threatened or endangered plant or animal species; (4) A typical representation of common geologic, soil, or water features; or (5) Outstanding or unusual geologic, soil, or water features. (b) [Reserved] ...

43 CFR 8223.0-5 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... threatened or endangered plant or animal species; (4) A typical representation of common geologic, soil, or water features; or (5) Outstanding or unusual geologic, soil, or water features. (b) [Reserved] ...

43 CFR 8223.0-5 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... threatened or endangered plant or animal species; (4) A typical representation of common geologic, soil, or water features; or (5) Outstanding or unusual geologic, soil, or water features. (b) [Reserved] ...

Surface profiling interferometer

DOEpatents

Takacs, Peter Z.; Qian, Shi-Nan

1989-01-01

The design of a long-trace surface profiler for the non-contact measurement of surface profile, slope error and curvature on cylindrical synchrotron radiation (SR) mirrors. The optical system is based upon the concept of a pencil-beam interferometer with an inherent large depth-of-field. The key feature of the optical system is the zero-path-difference beam splitter, which separates the laser beam into two colinear, variable-separation probe beams. A linear array detector is used to record the interference fringe in the image, and analysis of the fringe location as a function of scan position allows one to reconstruct the surface profile. The optical head is mounted on an air bearing slide with the capability to measure long aspheric optics, typical of those encountered in SR applications. A novel feature of the optical system is the use of a transverse "outrigger" beam which provides information on the relative alignment of the scan axis to the cylinder optic symmetry axis.

Characterization and Modeling of Nonfilamentary Ta/TaOx/TiO2/Ti Analog Synaptic Device

PubMed Central

Wang, Yu-Fen; Lin, Yen-Chuan; Wang, I-Ting; Lin, Tzu-Ping; Hou, Tuo-Hung

2015-01-01

A two-terminal analog synaptic device that precisely emulates biological synaptic features is expected to be a critical component for future hardware-based neuromorphic computing. Typical synaptic devices based on filamentary resistive switching face severe limitations on the implementation of concurrent inhibitory and excitatory synapses with low conductance and state fluctuation. For overcoming these limitations, we propose a Ta/TaOx/TiO2/Ti device with superior analog synaptic features. A physical simulation based on the homogeneous (nonfilamentary) barrier modulation induced by oxygen ion migration accurately reproduces various DC and AC evolutions of synaptic states, including the spike-timing-dependent plasticity and paired-pulse facilitation. Furthermore, a physics-based compact model for facilitating circuit-level design is proposed on the basis of the general definition of memristor devices. This comprehensive experimental and theoretical study of the promising electronic synapse can facilitate realizing large-scale neuromorphic systems. PMID:25955658

Fibroadenomatosis (fibroadenomatoid mastopathy): a benign breast lesion with composite pathologic features.

PubMed

Hanson, C A; Snover, D C; Dehner, L P

1987-10-01

A benign breast lesion with the composite histologic features of a fibroadenoma and fibrocystic changes has been referred to previously as fibroadenomatosis or fibroadenomatoid mastopathy; this lesion is distinct from the typical well circumscribed fibroadenoma that may have fibrocystic changes. The purpose of our study was to ascertain the frequency of this change among 200 consecutive breast biopsies and excisions with a coded pathologic diagnosis of fibroadenoma and/or "fibrocystic disease"; we identified these changes in 23 (11.5%) specimens. The lesion was characterized by microscopic fibroadenomatoid foci intermingled with dilated ducts, epitheliosis, and adenosis. It is suggested that fibroadenomatosis is yet another pattern in the complex morphologic spectrum known as benign proliferative breast disease. From our experience, this particular lesion was often appreciated as a unique finding, but the appropriate diagnostic designation was in question. The natural history of fibroadenomatosis is essentially unknown. It may represent a morphologic stage in the development of fibroadenoma(s).

The LArIAT experiment at Fermilab

DOE PAGES

Nutini, Irene

2016-03-01

The LArIAT experiment at Fermilab is part of the International Neutrino program recently approved in the US. LArIAT aims to measure the main features of charged particles interactions in argon in the energy range (0.2 - 2.0 GeV) corresponding to the energy spectrum of the same particles when produced in a neutrino-argon interaction (neutrino energies of few GeV) typical of the short- and long-baseline neutrino beams of the Neutrino Program. Data collected from the 1 st Run are being analyzed for both Physics studies and a technical characterization of the scintillation light collection system. Furthermore, two analysis topics are reported:more » the method developed for charged pion cross section measurement, based on the specific features of the LArTPC, and the development and test of the LArIAT custom-designed cold front-end electronics for SiPM devices to collect LAr scintillation light.« less

Manipulators with flexible links: A simple model and experiments

NASA Technical Reports Server (NTRS)

Shimoyama, Isao; Oppenheim, Irving J.

1989-01-01

A simple dynamic model proposed for flexible links is briefly reviewed and experimental control results are presented for different flexible systems. A simple dynamic model is useful for rapid prototyping of manipulators and their control systems, for possible application to manipulator design decisions, and for real time computation as might be applied in model based or feedforward control. Such a model is proposed, with the further advantage that clear physical arguments and explanations can be associated with its simplifying features and with its resulting analytical properties. The model is mathematically equivalent to Rayleigh's method. Taking the example of planar bending, the approach originates in its choice of two amplitude variables, typically chosen as the link end rotations referenced to the chord (or the tangent) motion of the link. This particular choice is key in establishing the advantageous features of the model, and it was used to support the series of experiments reported.

Modelling multimodal expression of emotion in a virtual agent.

PubMed

Pelachaud, Catherine

2009-12-12

Over the past few years we have been developing an expressive embodied conversational agent system. In particular, we have developed a model of multimodal behaviours that includes dynamism and complex facial expressions. The first feature refers to the qualitative execution of behaviours. Our model is based on perceptual studies and encompasses several parameters that modulate multimodal behaviours. The second feature, the model of complex expressions, follows a componential approach where a new expression is obtained by combining facial areas of other expressions. Lately we have been working on adding temporal dynamism to expressions. So far they have been designed statically, typically at their apex. Only full-blown expressions could be modelled. To overcome this limitation, we have defined a representation scheme that describes the temporal evolution of the expression of an emotion. It is no longer represented by a static definition but by a temporally ordered sequence of multimodal signals.

Tailored Algorithm for Sensitivity Enhancement of Gas Concentration Sensors Based on Tunable Laser Absorption Spectroscopy.

PubMed

Vargas-Rodriguez, Everardo; Guzman-Chavez, Ana Dinora; Baeza-Serrato, Roberto

2018-06-04

In this work, a novel tailored algorithm to enhance the overall sensitivity of gas concentration sensors based on the Direct Absorption Tunable Laser Absorption Spectroscopy (DA-ATLAS) method is presented. By using this algorithm, the sensor sensitivity can be custom-designed to be quasi constant over a much larger dynamic range compared with that obtained by typical methods based on a single statistics feature of the sensor signal output (peak amplitude, area under the curve, mean or RMS). Additionally, it is shown that with our algorithm, an optimal function can be tailored to get a quasi linear relationship between the concentration and some specific statistics features over a wider dynamic range. In order to test the viability of our algorithm, a basic C 2 H 2 sensor based on DA-ATLAS was implemented, and its experimental measurements support the simulated results provided by our algorithm.

Recent Observations and Modeling of Narrowband Stimulated Electromagnetic Emissions SEEs at HAARP and EISCAT

NASA Astrophysics Data System (ADS)

Scales, W.; Mahmoudian, A.; Fu, H.; Bordikar, M. R.; Samimi, A.; Bernhardt, P. A.; Briczinski, S. J., Jr.; Kosch, M. J.; Senior, A.; Isham, B.

2014-12-01

There has been significant interest in so-called narrowband Stimulated Electromagnetic Emission SEE over the past several years due to recent discoveries at the High Frequency Active Auroral Research Program HAARP facility near Gakone, Alaska. Narrowband SEE (NSEE) has been defined as spectral features in the SEE spectrum typically within 1 kHz of the transmitter (or pump) frequency. SEE is due to nonlinear processes leading to re-radiation at frequencies other than the pump wave frequency during heating the ionospheric plasma with high power HF radio waves. Although NSEE exhibits a richly complex structure, it has now been shown after a substantial number of observations at HAARP, that NSEE can be grouped into two basic classes. The first are those spectral features, associated with Stimulated Brillouin Scatter SBS, which typically occur when the pump frequency is not close to electron gyro-harmonic frequencies. Typically, these spectral features are within roughly 50 Hz of the pump wave frequency where it is to be noted that the O+ ion gyro-frequency is roughly 50 Hz. The second class of spectral features corresponds to the case when the pump wave frequency is typically within roughly 10 kHz of electron gyro-harmonic frequencies. In this case, spectral features ordered by harmonics of ion gyro-frequencies are typically observed, and termed Stimulated Ion Bernstein Scatter SIBS. This presentation will first provide an overview of the recent NSEE experimental observations at HAARP. Both Stimulated Brillouin Scatter SBS and Stimulated Ion Bernstein Scatter SIBS observations will be discussed as well as their relationship to each other. Possible theoretical formulation in terms of parametric decay instabilities and computational modeling will be provided. Possible applications of NSEE will be pointed out including triggering diagnostics for artificial ionization layer formation, proton precipitation event diagnostics, electron temperature measurements in the heated volume and detection of heavy ion species. Finally potential for observing such SEE at the European Incoherent Scatter EISCAT facility will be discussed.

Design rules for phase-change materials in data storage applications.

PubMed

Lencer, Dominic; Salinga, Martin; Wuttig, Matthias

2011-05-10

Phase-change materials can rapidly and reversibly be switched between an amorphous and a crystalline phase. Since both phases are characterized by very different optical and electrical properties, these materials can be employed for rewritable optical and electrical data storage. Hence, there are considerable efforts to identify suitable materials, and to optimize them with respect to specific applications. Design rules that can explain why the materials identified so far enable phase-change based devices would hence be very beneficial. This article describes materials that have been successfully employed and dicusses common features regarding both typical structures and bonding mechanisms. It is shown that typical structural motifs and electronic properties can be found in the crystalline state that are indicative for resonant bonding, from which the employed contrast originates. The occurence of resonance is linked to the composition, thus providing a design rule for phase-change materials. This understanding helps to unravel characteristic properties such as electrical and thermal conductivity which are discussed in the subsequent section. Then, turning to the transition kinetics between the phases, the current understanding and modeling of the processes of amorphization and crystallization are discussed. Finally, present approaches for improved high-capacity optical discs and fast non-volatile electrical memories, that hold the potential to succeed present-day's Flash memory, are presented. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Scalable Molecular Dynamics with NAMD

PubMed Central

Phillips, James C.; Braun, Rosemary; Wang, Wei; Gumbart, James; Tajkhorshid, Emad; Villa, Elizabeth; Chipot, Christophe; Skeel, Robert D.; Kalé, Laxmikant; Schulten, Klaus

2008-01-01

NAMD is a parallel molecular dynamics code designed for high-performance simulation of large biomolecular systems. NAMD scales to hundreds of processors on high-end parallel platforms, as well as tens of processors on low-cost commodity clusters, and also runs on individual desktop and laptop computers. NAMD works with AMBER and CHARMM potential functions, parameters, and file formats. This paper, directed to novices as well as experts, first introduces concepts and methods used in the NAMD program, describing the classical molecular dynamics force field, equations of motion, and integration methods along with the efficient electrostatics evaluation algorithms employed and temperature and pressure controls used. Features for steering the simulation across barriers and for calculating both alchemical and conformational free energy differences are presented. The motivations for and a roadmap to the internal design of NAMD, implemented in C++ and based on Charm++ parallel objects, are outlined. The factors affecting the serial and parallel performance of a simulation are discussed. Next, typical NAMD use is illustrated with representative applications to a small, a medium, and a large biomolecular system, highlighting particular features of NAMD, e.g., the Tcl scripting language. Finally, the paper provides a list of the key features of NAMD and discusses the benefits of combining NAMD with the molecular graphics/sequence analysis software VMD and the grid computing/collaboratory software BioCoRE. NAMD is distributed free of charge with source code at www.ks.uiuc.edu. PMID:16222654

Inferring Broad Regulatory Biology from Time Course Data: Have We Reached an Upper Bound under Constraints Typical of In Vivo Studies?

PubMed Central

Craddock, Travis J. A.; Fletcher, Mary Ann; Klimas, Nancy G.

2015-01-01

There is a growing appreciation for the network biology that regulates the coordinated expression of molecular and cellular markers however questions persist regarding the identifiability of these networks. Here we explore some of the issues relevant to recovering directed regulatory networks from time course data collected under experimental constraints typical of in vivo studies. NetSim simulations of sparsely connected biological networks were used to evaluate two simple feature selection techniques used in the construction of linear Ordinary Differential Equation (ODE) models, namely truncation of terms versus latent vector projection. Performance was compared with ODE-based Time Series Network Identification (TSNI) integral, and the information-theoretic Time-Delay ARACNE (TD-ARACNE). Projection-based techniques and TSNI integral outperformed truncation-based selection and TD-ARACNE on aggregate networks with edge densities of 10-30%, i.e. transcription factor, protein-protein cliques and immune signaling networks. All were more robust to noise than truncation-based feature selection. Performance was comparable on the in silico 10-node DREAM 3 network, a 5-node Yeast synthetic network designed for In vivo Reverse-engineering and Modeling Assessment (IRMA) and a 9-node human HeLa cell cycle network of similar size and edge density. Performance was more sensitive to the number of time courses than to sample frequency and extrapolated better to larger networks by grouping experiments. In all cases performance declined rapidly in larger networks with lower edge density. Limited recovery and high false positive rates obtained overall bring into question our ability to generate informative time course data rather than the design of any particular reverse engineering algorithm. PMID:25984725

Audible Beaconing with Accessible Pedestrian Signals

PubMed Central

Barlow, Janet M.; Scott, Alan C.; Bentzen, Billie Louise

2010-01-01

Purpose Although Accessible Pedestrian Signals (APS) are often assumed to provide wayfinding information, the type of APS that has been typically installed in the U.S has not had positive effects on finding crosswalks, locating pushbuttons, or providing directional guidance. This paper reports the results of research on crossings by blind pedestrians at complex signalized intersections, before and after the installation of APS with innovative audible beaconing features, designed to improve wayfinding. Methods Objective data on measures of street crossing performance by 56 participants was obtained at four intersections, two each in Charlotte, NC, and Portland, OR. Results In the first round of testing, APS with beaconing features resulted in only slightly improved wayfinding. Revisions to the audible beaconing features resulted in improved performance on four measures of wayfinding as compared to the pre-installation condition: beginning crossings within the crosswalk, ending crossings within the crosswalk, independence in finding the starting location, and independence in aligning to cross. Implications for Practice Use of APS that provide beaconing from the far-end of the crosswalk show promise of improving wayfinding at street crossings. PMID:20622978

Quantification of uncertainty in machining operations for on-machine acceptance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Claudet, Andre A.; Tran, Hy D.; Su, Jiann-Chemg

2008-09-01

Manufactured parts are designed with acceptance tolerances, i.e. deviations from ideal design conditions, due to unavoidable errors in the manufacturing process. It is necessary to measure and evaluate the manufactured part, compared to the nominal design, to determine whether the part meets design specifications. The scope of this research project is dimensional acceptance of machined parts; specifically, parts machined using numerically controlled (NC, or also CNC for Computer Numerically Controlled) machines. In the design/build/accept cycle, the designer will specify both a nominal value, and an acceptable tolerance. As part of the typical design/build/accept business practice, it is required to verifymore » that the part did meet acceptable values prior to acceptance. Manufacturing cost must include not only raw materials and added labor, but also the cost of ensuring conformance to specifications. Ensuring conformance is a substantial portion of the cost of manufacturing. In this project, the costs of measurements were approximately 50% of the cost of the machined part. In production, cost of measurement would be smaller, but still a substantial proportion of manufacturing cost. The results of this research project will point to a science-based approach to reducing the cost of ensuring conformance to specifications. The approach that we take is to determine, a priori, how well a CNC machine can manufacture a particular geometry from stock. Based on the knowledge of the manufacturing process, we are then able to decide features which need further measurements from features which can be accepted 'as is' from the CNC. By calibration of the machine tool, and establishing a machining accuracy ratio, we can validate the ability of CNC to fabricate to a particular level of tolerance. This will eliminate the costs of checking for conformance for relatively large tolerances.« less

A Comparative Study of Standardized Infinity Reference and Average Reference for EEG of Three Typical Brain States

PubMed Central

Zheng, Gaoxing; Qi, Xiaoying; Li, Yuzhu; Zhang, Wei; Yu, Yuguo

2018-01-01

The choice of different reference electrodes plays an important role in deciphering the functional meaning of electroencephalography (EEG) signals. In recent years, the infinity zero reference using the reference electrode standard technique (REST) has been increasingly applied, while the average reference (AR) was generally advocated as the best available reference option in previous classical EEG studies. Here, we designed EEG experiments and performed a direct comparison between the influences of REST and AR on EEG-revealed brain activity features for three typical brain behavior states (eyes-closed, eyes-open and music-listening). The analysis results revealed the following observations: (1) there is no significant difference in the alpha-wave-blocking effect during the eyes-open state compared with the eyes-closed state for both REST and AR references; (2) there was clear frontal EEG asymmetry during the resting state, and the degree of lateralization under REST was higher than that under AR; (3) the global brain functional connectivity density (FCD) and local FCD have higher values for REST than for AR under different behavior states; and (4) the value of the small-world network characteristic in the eyes-closed state is significantly (in full, alpha, beta and gamma frequency bands) higher than that in the eyes-open state, and the small-world effect under the REST reference is higher than that under AR. In addition, the music-listening state has a higher small-world network effect than the eyes-closed state. The above results suggest that typical EEG features might be more clearly presented by applying the REST reference than by applying AR when using a 64-channel recording. PMID:29593490

Industry-relevant magnetron sputtering and cathodic arc ultra-high vacuum deposition system for in situ x-ray diffraction studies of thin film growth using high energy synchrotron radiation.

PubMed

Schroeder, J L; Thomson, W; Howard, B; Schell, N; Näslund, L-Å; Rogström, L; Johansson-Jõesaar, M P; Ghafoor, N; Odén, M; Nothnagel, E; Shepard, A; Greer, J; Birch, J

2015-09-01

We present an industry-relevant, large-scale, ultra-high vacuum (UHV) magnetron sputtering and cathodic arc deposition system purposefully designed for time-resolved in situ thin film deposition/annealing studies using high-energy (>50 keV), high photon flux (>10(12) ph/s) synchrotron radiation. The high photon flux, combined with a fast-acquisition-time (<1 s) two-dimensional (2D) detector, permits time-resolved in situ structural analysis of thin film formation processes. The high-energy synchrotron-radiation based x-rays result in small scattering angles (<11°), allowing large areas of reciprocal space to be imaged with a 2D detector. The system has been designed for use on the 1-tonne, ultra-high load, high-resolution hexapod at the P07 High Energy Materials Science beamline at PETRA III at the Deutsches Elektronen-Synchrotron in Hamburg, Germany. The deposition system includes standard features of a typical UHV deposition system plus a range of special features suited for synchrotron radiation studies and industry-relevant processes. We openly encourage the materials research community to contact us for collaborative opportunities using this unique and versatile scientific instrument.

Using Approximations to Accelerate Engineering Design Optimization

NASA Technical Reports Server (NTRS)

Torczon, Virginia; Trosset, Michael W.

1998-01-01

Optimization problems that arise in engineering design are often characterized by several features that hinder the use of standard nonlinear optimization techniques. Foremost among these features is that the functions used to define the engineering optimization problem often are computationally intensive. Within a standard nonlinear optimization algorithm, the computational expense of evaluating the functions that define the problem would necessarily be incurred for each iteration of the optimization algorithm. Faced with such prohibitive computational costs, an attractive alternative is to make use of surrogates within an optimization context since surrogates can be chosen or constructed so that they are typically much less expensive to compute. For the purposes of this paper, we will focus on the use of algebraic approximations as surrogates for the objective. In this paper we introduce the use of so-called merit functions that explicitly recognize the desirability of improving the current approximation to the objective during the course of the optimization. We define and experiment with the use of merit functions chosen to simultaneously improve both the solution to the optimization problem (the objective) and the quality of the approximation. Our goal is to further improve the effectiveness of our general approach without sacrificing any of its rigor.

A Thermal Physiological Comparison of Two HazMat Protective Ensembles With and Without Active Convective Cooling

NASA Technical Reports Server (NTRS)

Williamson, Rebecca; Carbo, Jorge; Luna, Bernadette; Webbon, Bruce W.

1998-01-01

Wearing impermeable garments for hazardous materials clean up can often present a health and safety problem for the wearer. Even short duration clean up activities can produce heat stress injuries in hazardous materials workers. It was hypothesized that an internal cooling system might increase worker productivity and decrease likelihood of heat stress injuries in typical HazMat operations. Two HazMat protective ensembles were compared during treadmill exercise. The different ensembles were created using two different suits: a Trelleborg VPS suit representative of current HazMat suits and a prototype suit developed by NASA engineers. The two life support systems used were a current technology Interspiro Spirolite breathing apparatus and a liquid air breathing system that also provided convective cooling. Twelve local members of a HazMat team served as test subjects. They were fully instrumented to allow a complete physiological comparison of their thermal responses to the different ensembles. Results showed that cooling from the liquid air system significantly decreased thermal stress. The results of the subjective evaluations of new design features in the prototype suit were also highly favorable. Incorporation of these new design features could lead to significant operational advantages in the future.

The rope sign: a case of interstitial granulomatous dermatitis with arthritis.

PubMed

Savoia, Francesco; Stinchi, Caterina; Gaddoni, Giuseppe; Patrizi, Annalisa; Odorici, Giulia; Tengattini, Vera; Cataleta, Pierluigi; Zago, Silvia

2016-02-01

Interstitial granulomatous dermatitis with arthritis (IGDA), also known as Ackerman's syndrome, is a rare cutaneous disease classically characterized by the triad of cutaneous cords, a typical histologic infiltrate mainly constituted by histiocytes and arthritis/connective tissue disease. Here we report the case of IGDA with the typical clinical and histological features in a patient affected by lupus erythematosus. In this article we underline that IGDA may have a variety of different clinical and histological features. The rope sign is typical but infrequent, while histology is usually characteristic and shows a dermal inflammatory infiltrate, with a predominance of histiocytes, localized interstitially and in a palisaded array between collagen fibres, that show signs of degeneration. Clinical and histological differential diagnoses are discussed.

Computer aided diagnosis based on medical image processing and artificial intelligence methods

NASA Astrophysics Data System (ADS)

Stoitsis, John; Valavanis, Ioannis; Mougiakakou, Stavroula G.; Golemati, Spyretta; Nikita, Alexandra; Nikita, Konstantina S.

2006-12-01

Advances in imaging technology and computer science have greatly enhanced interpretation of medical images, and contributed to early diagnosis. The typical architecture of a Computer Aided Diagnosis (CAD) system includes image pre-processing, definition of region(s) of interest, features extraction and selection, and classification. In this paper, the principles of CAD systems design and development are demonstrated by means of two examples. The first one focuses on the differentiation between symptomatic and asymptomatic carotid atheromatous plaques. For each plaque, a vector of texture and motion features was estimated, which was then reduced to the most robust ones by means of ANalysis of VAriance (ANOVA). Using fuzzy c-means, the features were then clustered into two classes. Clustering performances of 74%, 79%, and 84% were achieved for texture only, motion only, and combinations of texture and motion features, respectively. The second CAD system presented in this paper supports the diagnosis of focal liver lesions and is able to characterize liver tissue from Computed Tomography (CT) images as normal, hepatic cyst, hemangioma, and hepatocellular carcinoma. Five texture feature sets were extracted for each lesion, while a genetic algorithm based feature selection method was applied to identify the most robust features. The selected feature set was fed into an ensemble of neural network classifiers. The achieved classification performance was 100%, 93.75% and 90.63% in the training, validation and testing set, respectively. It is concluded that computerized analysis of medical images in combination with artificial intelligence can be used in clinical practice and may contribute to more efficient diagnosis.

Making automated computer program documentation a feature of total system design

NASA Technical Reports Server (NTRS)

Wolf, A. W.

1970-01-01

It is pointed out that in large-scale computer software systems, program documents are too often fraught with errors, out of date, poorly written, and sometimes nonexistent in whole or in part. The means are described by which many of these typical system documentation problems were overcome in a large and dynamic software project. A systems approach was employed which encompassed such items as: (1) configuration management; (2) standards and conventions; (3) collection of program information into central data banks; (4) interaction among executive, compiler, central data banks, and configuration management; and (5) automatic documentation. A complete description of the overall system is given.

Decision-theoretic control of EUVE telescope scheduling

NASA Technical Reports Server (NTRS)

Hansson, Othar; Mayer, Andrew

1993-01-01

This paper describes a decision theoretic scheduler (DTS) designed to employ state-of-the-art probabilistic inference technology to speed the search for efficient solutions to constraint-satisfaction problems. Our approach involves assessing the performance of heuristic control strategies that are normally hard-coded into scheduling systems and using probabilistic inference to aggregate this information in light of the features of a given problem. The Bayesian Problem-Solver (BPS) introduced a similar approach to solving single agent and adversarial graph search patterns yielding orders-of-magnitude improvement over traditional techniques. Initial efforts suggest that similar improvements will be realizable when applied to typical constraint-satisfaction scheduling problems.

Experiments with a decision-theoretic scheduler

NASA Technical Reports Server (NTRS)

Hansson, Othar; Holt, Gerhard; Mayer, Andrew

1992-01-01

This paper describes DTS, a decision-theoretic scheduler designed to employ state-of-the-art probabilistic inference technology to speed the search for efficient solutions to constraint-satisfaction problems. Our approach involves assessing the performance of heuristic control strategies that are normally hard-coded into scheduling systems, and using probabilistic inference to aggregate this information in light of features of a given problem. BPS, the Bayesian Problem-Solver, introduced a similar approach to solving single-agent and adversarial graph search problems, yielding orders-of-magnitude improvement over traditional techniques. Initial efforts suggest that similar improvements will be realizable when applied to typical constraint-satisfaction scheduling problems.

A microspectrometer based on subwavelength metal nanohole array

NASA Astrophysics Data System (ADS)

Cui, Jun; Xia, Liangping; Yang, Zheng; Yin, Lu; Zheng, Guoxing; Yin, Shaoyun; Du, Chunlei

2014-11-01

Catering to the active demand of the miniaturization of spectrometers, a simple microspectrometer with small size and light weight is presented in this paper. The presented microspectrometer is a typical filter-based spectrometer using the extraordinary optical transmission property of subwavelength metal hole array structure. Different subwavelength metal nanohole arrays are designed to work as different filter units obtained by changing the lattice parameters. By processing the filter spectra with a unique algorithm based on sparse representation, the proposed spectrometer is demonstrated to have the capability of high spectral resolution and accuracy. Benefit for the thin filmed feature, the microspectrometer is expected to find its application in integrated optical systems.

Managing Personal and Group Collections of Information

NASA Technical Reports Server (NTRS)

Wolfe, Shawn R.; Wragg, Stephen D.; Chen, James R.; Koga, Dennis (Technical Monitor)

1999-01-01

The internet revolution has dramatically increased the amount of information available to users. Various tools such as search engines have been developed to help users find the information they need from this vast repository. Users often also need tools to help manipulate the growing amount of useful information they have discovered. Current tools available for this purpose are typically local components of web browsers designed to manage URL bookmarks. They provide limited functionalities to handle high information complexities. To tackle this have created DIAMS, an agent-based tool to help users or groups manage their information collections and share their collections with other. the main features of DIAMS are described here.

Design intent optimization at the beyond 7nm node: the intersection of DTCO and EUVL stochastic mitigation techniques

NASA Astrophysics Data System (ADS)

Crouse, Michael; Liebmann, Lars; Plachecki, Vince; Salama, Mohamed; Chen, Yulu; Saulnier, Nicole; Dunn, Derren; Matthew, Itty; Hsu, Stephen; Gronlund, Keith; Goodwin, Francis

2017-03-01

The initial readiness of EUV patterning was demonstrated in 2016 with IBM Alliance's 7nm device technology. The focus has now shifted to driving the 'effective' k1 factor and enabling the second generation of EUV patterning. Thus, Design Technology Co-optimization (DTCO) has become a critical part of technology enablement as scaling has become more challenging and the industry pushes the limits of EUV lithography. The working partnership between the design teams and the process development teams typically involves an iterative approach to evaluate the manufacturability of proposed designs, subsequent modifications to those designs and finally a design manual for the technology. While this approach has served the industry well for many generations, the challenges at the Beyond 7nm node require a more efficient approach. In this work, we describe the use of "Design Intent" lithographic layout optimization where we remove the iterative component of DTCO and replace it with an optimization that achieves both a "patterning friendly" design and minimizes the well-known EUV stochastic effects. Solved together, this "design intent" approach can more quickly achieve superior lithographic results while still meeting the original device's functional specifications. Specifically, in this work we will demonstrate "design intent" optimization for critical BEOL layers using design tolerance bands to guide the source mask co-optimization. The design tolerance bands can be either supplied as part of the original design or derived from some basic rules. Additionally, the EUV stochastic behavior is mitigated by enhancing the image log slope (ILS) for specific key features as part of the overall optimization. We will show the benefit of the "design intent approach" on both bidirectional and unidirectional 28nm min pitch standard logic layouts and compare the more typical iterative SMO approach. Thus demonstrating the benefit of allowing the design to float within the specified range. Lastly, we discuss how the evolution of this approach could lead to layout optimization based entirely on some minimal set of functional requirements and process constraints.

Deformation processes within wheel-rail adhesion in contact area

NASA Astrophysics Data System (ADS)

Albagachiev, A. Yu; Keropyan, A. M.

2018-03-01

The study of working surface deformation during interaction of open-pit locomotive tires allowed defining outstanding features of phenomena occurring in the contact area of interacting surfaces. It was found that processes typical for plastic saturated contact occur in the area of wheel-rail interaction of industrial railway transport. In case of plastic deformation exposed to heavy loads typical for open-pit locomotives, upon all rough surfaces of the contour contact area being fully deformed, the frame on which they are found is exposed to plastic deformation. Plastic deformation of roughness within the contact area of interacting surfaces leads to the increase in the actual area of their contact and, therefore, increases the towing capacity of mining machines. Finally, the available data on deformation characteristics with regard to processes occurring in the contact area of wheel-rail interaction will allow making theoretical forecasts on the expected design value of friction coefficient and, therefore, the towing capacity of open-pit locomotives.

IR window design for hypersonic missile seekers: thermal shock and cooling systems

NASA Astrophysics Data System (ADS)

Hingst, Uwe; Koerber, Stefan

2001-10-01

Infra-red (IR) seekers on missiles at high Mach-numbers in the lower tier air defence often suffer from degradation in performance due to aerothermodynamic effects. The kind and rate of degradation depends on the geometric design (shape) and location of the IR-window. Optimal design may reduce those effects but still misses to totally withstand the imposed thermal stresses (thermal shock). Proper thermal protection systems and/or window cooling systems will be needed. The first part of this paper deals particularly with passive IR- window design features to reduce the thermal stresses. A series of wind-tunnel testings focused on the thermal shock behavior of different IR-window shapes under critical flight conditions. The variation of typical design parameters demonstrates the available features to reduce thermal shock by passive ways. The second part presents active thermal stress reduction devices, e.g. an active cooling system. Among others the most efficient reduction of thermal heating is based on three components: A partial coverage of the IR-dome to protect most parts against heating effects, a rotating system bearing the IR-dome and a liquid spray-cooling system in the gap between the cover and the IR-dome. The hemispherical or pyramidal dome can be located either midways in the missile nose section or sideways on the structure. The liquid spray cooling system combines both, a heat exchange by fluid evaporation and a heat transfer by fluid and gas cross flow (convection), causing a low fluid consumption. Such a cooling system along with their driving parameters and the resulting analytical performance will be presented.

Establishing the situated features associated with perceived stress

PubMed Central

Lebois, Lauren A.M.; Hertzog, Christopher; Slavich, George M.; Barrett, Lisa Feldman; Barsalou, Lawrence W.

2016-01-01

We propose that the domain general process of categorization contributes to the perception of stress. When a situation contains features associated with stressful experiences, it is categorized as stressful. From the perspective of situated cognition, the features used to categorize experiences as stressful are the features typically true of stressful situations. To test this hypothesis, we asked participants to evaluate the perceived stress of 572 imagined situations, and to also evaluate each situation for how much it possessed 19 features potentially associated with stressful situations and their processing (e.g., self-threat, familiarity, visual imagery, outcome certainty). Following variable reduction through factor analysis, a core set of 8 features associated with stressful situations—expectation violation, self-threat, coping efficacy, bodily experience, arousal, negative valence, positive valence, and perseveration—all loaded on a single Core Stress Features factor. In a multilevel model, this factor and an Imagery factor explained 88% of the variance in judgments of perceived stress, with significant random effects reflecting differences in how individual participants categorized stress. These results support the hypothesis that people categorize situations as stressful to the extent that typical features of stressful situations are present. To our knowledge, this is the first attempt to establish a comprehensive set of features that predicts perceived stress. PMID:27288834

Three-dimensional counting of morphologically normal human red blood cells via digital holographic microscopy

NASA Astrophysics Data System (ADS)

Yi, Faliu; Moon, Inkyu; Lee, Yeon H.

2015-01-01

Counting morphologically normal cells in human red blood cells (RBCs) is extremely beneficial in the health care field. We propose a three-dimensional (3-D) classification method of automatically determining the morphologically normal RBCs in the phase image of multiple human RBCs that are obtained by off-axis digital holographic microscopy (DHM). The RBC holograms are first recorded by DHM, and then the phase images of multiple RBCs are reconstructed by a computational numerical algorithm. To design the classifier, the three typical RBC shapes, which are stomatocyte, discocyte, and echinocyte, are used for training and testing. Nonmain or abnormal RBC shapes different from the three normal shapes are defined as the fourth category. Ten features, including projected surface area, average phase value, mean corpuscular hemoglobin, perimeter, mean corpuscular hemoglobin surface density, circularity, mean phase of center part, sphericity coefficient, elongation, and pallor, are extracted from each RBC after segmenting the reconstructed phase images by using a watershed transform algorithm. Moreover, four additional properties, such as projected surface area, perimeter, average phase value, and elongation, are measured from the inner part of each cell, which can give significant information beyond the previous 10 features for the separation of the RBC groups; these are verified in the experiment by the statistical method of Hotelling's T-square test. We also apply the principal component analysis algorithm to reduce the dimension number of variables and establish the Gaussian mixture densities using the projected data with the first eight principal components. Consequently, the Gaussian mixtures are used to design the discriminant functions based on Bayesian decision theory. To improve the performance of the Bayes classifier and the accuracy of estimation of its error rate, the leaving-one-out technique is applied. Experimental results show that the proposed method can yield good results for calculating the percentage of each typical normal RBC shape in a reconstructed phase image of multiple RBCs that will be favorable to the analysis of RBC-related diseases. In addition, we show that the discrimination performance for the counting of normal shapes of RBCs can be improved by using 3-D features of an RBC.

GENET note no. 1

NASA Technical Reports Server (NTRS)

Yeh, J. W.

1971-01-01

The general features of the GENET system for simulating networks are described. A set of features is presented which are desirable for network simulations and which are expected to be achieved by this system. Among these features are: (1) two level network modeling; and (2) problem oriented operations. Several typical network systems are modeled in GENET framework to illustrate various of the features and to show its applicability.

Comparative evaluation of support vector machine classification for computer aided detection of breast masses in mammography

NASA Astrophysics Data System (ADS)

Lesniak, J. M.; Hupse, R.; Blanc, R.; Karssemeijer, N.; Székely, G.

2012-08-01

False positive (FP) marks represent an obstacle for effective use of computer-aided detection (CADe) of breast masses in mammography. Typically, the problem can be approached either by developing more discriminative features or by employing different classifier designs. In this paper, the usage of support vector machine (SVM) classification for FP reduction in CADe is investigated, presenting a systematic quantitative evaluation against neural networks, k-nearest neighbor classification, linear discriminant analysis and random forests. A large database of 2516 film mammography examinations and 73 input features was used to train the classifiers and evaluate for their performance on correctly diagnosed exams as well as false negatives. Further, classifier robustness was investigated using varying training data and feature sets as input. The evaluation was based on the mean exam sensitivity in 0.05-1 FPs on normals on the free-response receiver operating characteristic curve (FROC), incorporated into a tenfold cross validation framework. It was found that SVM classification using a Gaussian kernel offered significantly increased detection performance (P = 0.0002) compared to the reference methods. Varying training data and input features, SVMs showed improved exploitation of large feature sets. It is concluded that with the SVM-based CADe a significant reduction of FPs is possible outperforming other state-of-the-art approaches for breast mass CADe.

Learning a novel phonological contrast depends on interactions between individual differences and training paradigm design.

PubMed

Perrachione, Tyler K; Lee, Jiyeon; Ha, Louisa Y Y; Wong, Patrick C M

2011-07-01

Studies evaluating phonological contrast learning typically investigate either the predictiveness of specific pretraining aptitude measures or the efficacy of different instructional paradigms. However, little research considers how these factors interact--whether different students learn better from different types of instruction--and what the psychological basis for any interaction might be. The present study demonstrates that successfully learning a foreign-language phonological contrast for pitch depends on an interaction between individual differences in perceptual abilities and the design of the training paradigm. Training from stimuli with high acoustic-phonetic variability is generally thought to improve learning; however, we found high-variability training enhanced learning only for individuals with strong perceptual abilities. Learners with weaker perceptual abilities were actually impaired by high-variability training relative to a low-variability condition. A second experiment assessing variations on the high-variability training design determined that the property of this learning environment most detrimental to perceptually weak learners is the amount of trial-by-trial variability. Learners' perceptual limitations can thus override the benefits of high-variability training where trial-by-trial variability in other irrelevant acoustic-phonetic features obfuscates access to the target feature. These results demonstrate the importance of considering individual differences in pretraining aptitudes when evaluating the efficacy of any speech training paradigm. © 2011 Acoustical Society of America

ForceAtlas2, a continuous graph layout algorithm for handy network visualization designed for the Gephi software.

PubMed

Jacomy, Mathieu; Venturini, Tommaso; Heymann, Sebastien; Bastian, Mathieu

2014-01-01

Gephi is a network visualization software used in various disciplines (social network analysis, biology, genomics...). One of its key features is the ability to display the spatialization process, aiming at transforming the network into a map, and ForceAtlas2 is its default layout algorithm. The latter is developed by the Gephi team as an all-around solution to Gephi users' typical networks (scale-free, 10 to 10,000 nodes). We present here for the first time its functioning and settings. ForceAtlas2 is a force-directed layout close to other algorithms used for network spatialization. We do not claim a theoretical advance but an attempt to integrate different techniques such as the Barnes Hut simulation, degree-dependent repulsive force, and local and global adaptive temperatures. It is designed for the Gephi user experience (it is a continuous algorithm), and we explain which constraints it implies. The algorithm benefits from much feedback and is developed in order to provide many possibilities through its settings. We lay out its complete functioning for the users who need a precise understanding of its behaviour, from the formulas to graphic illustration of the result. We propose a benchmark for our compromise between performance and quality. We also explain why we integrated its various features and discuss our design choices.

ForceAtlas2, a Continuous Graph Layout Algorithm for Handy Network Visualization Designed for the Gephi Software

PubMed Central

Jacomy, Mathieu; Venturini, Tommaso; Heymann, Sebastien; Bastian, Mathieu

2014-01-01

Gephi is a network visualization software used in various disciplines (social network analysis, biology, genomics…). One of its key features is the ability to display the spatialization process, aiming at transforming the network into a map, and ForceAtlas2 is its default layout algorithm. The latter is developed by the Gephi team as an all-around solution to Gephi users’ typical networks (scale-free, 10 to 10,000 nodes). We present here for the first time its functioning and settings. ForceAtlas2 is a force-directed layout close to other algorithms used for network spatialization. We do not claim a theoretical advance but an attempt to integrate different techniques such as the Barnes Hut simulation, degree-dependent repulsive force, and local and global adaptive temperatures. It is designed for the Gephi user experience (it is a continuous algorithm), and we explain which constraints it implies. The algorithm benefits from much feedback and is developed in order to provide many possibilities through its settings. We lay out its complete functioning for the users who need a precise understanding of its behaviour, from the formulas to graphic illustration of the result. We propose a benchmark for our compromise between performance and quality. We also explain why we integrated its various features and discuss our design choices. PMID:24914678

Passive flow regulators for drug delivery and hydrocephalus treatment

NASA Astrophysics Data System (ADS)

Chappel, E.; Dumont-Fillon, D.; Mefti, S.

2014-03-01

Passive flow regulators are usually intended to deliver or drain a fluid at a constant rate independently from pressure variations. New designs of passive flow regulators made of a stack of a silicon membrane anodically bonded to a Pyrex substrate are proposed. A first design has been built for the derivation of cerebrospinal fluid (CSF) towards peritoneum for hydrocephalus treatment. The device allows draining CSF at the patient production rate independently from postural changes. The flow rate is regulated at 20 ml/h in the range 10 to 40 mbar. Specific features to adjust in vivo the nominal flow rate are shown. A second design including high pressure shut-off feature has been made. The intended use is drug delivery with pressurized reservoir of typically 100 to 300 mbar. In both cases, the membrane comprises several holes facing pillars in the Pyrex substrate. These pillars are machined in a cavity which ensures a gap between the membrane and the pillars at rest. The fluid in the pressurized reservoir is directly in contact with the top surface of the membrane, inducing its deflection towards Pyrex substrate and closing progressively the fluidic pathway through each hole of the membrane. Since the membrane deflection is highly non-linear, FEM simulations have been performed to determine both radial position and diameter of the membrane holes that ensure a constant flow rate for a given range of pressure.

Effects of achievement contexts on the meaning structure of emotion words.

PubMed

Gentsch, Kornelia; Loderer, Kristina; Soriano, Cristina; Fontaine, Johnny R J; Eid, Michael; Pekrun, Reinhard; Scherer, Klaus R

2018-03-01

Little is known about the impact of context on the meaning of emotion words. In the present study, we used a semantic profiling instrument (GRID) to investigate features representing five emotion components (appraisal, bodily reaction, expression, action tendencies, and feeling) of 11 emotion words in situational contexts involving success or failure. We compared these to the data from an earlier study in which participants evaluated the typicality of features out of context. Profile analyses identified features for which typicality changed as a function of context for all emotion words, except contentment, with appraisal features being most frequently affected. Those context effects occurred for both hypothesised basic and non-basic emotion words. Moreover, both data sets revealed a four-dimensional structure. The four dimensions were largely similar (valence, power, arousal, and novelty). The results suggest that context may not change the underlying dimensionality but affects facets of the meaning of emotion words.

Acoustic Performance of the GEAE UPS Research Fan in the NASA Glenn 9- by 15-Foot Low-Speed Wind Tunnel

NASA Technical Reports Server (NTRS)

Woodward, Richard P.; Hughes, Christopher E.

2012-01-01

A model advanced turbofan was acoustically tested in the NASA Glenn 9- by 15-Foot Low-Speed Wind Tunnel in 1994. The Universal Propulsion Simulator fan was designed and manufactured by General Electric Aircraft Engines, and included an active core, as well as bypass, flow paths. The fan was tested with several rotors featuring unswept, forward-swept and aft-swept designs of both metal and composite construction. Sideline acoustic data were taken with both hard and acoustically treated walls in the flow passages. The fan was tested within an airflow at a Mach number of 0.20, which is representative of aircraft takeoff/approach conditions. All rotors showed similar aerodynamic performance. However, the composite rotors typically showed higher noise levels than did corresponding metal rotors. Aft and forward rotor sweep showed at most modest reductions of transonic multiple pure tone levels. However, rotor sweep often introduced increased rotor-stator interaction tone levels. Broadband noise was typically higher for the composite rotors and also for the aft-swept metal rotor. Transonic MPT generation was reduced with increasing fan axis angle of attack (AOA); however, higher downstream noise levels did increase with AOA resulting in higher overall Effective Perceived Noise Level.

Agile Task Tracking Tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duke, Roger T.; Crump, Thomas Vu

The work was created to provide a tool for the purpose of improving the management of tasks associated with Agile projects. Agile projects are typically completed in an iterative manner with many short duration tasks being performed as part of iterations. These iterations are generally referred to as sprints. The objective of this work is to create a single tool that enables sprint teams to manage all of their tasks in multiple sprints and automatically produce all standard sprint performance charts with minimum effort. The format of the printed work is designed to mimic a standard Kanban board. The workmore » is developed as a single Excel file with worksheets capable of managing up to five concurrent sprints and up to one hundred tasks. It also includes a summary worksheet providing performance information from all active sprints. There are many commercial project management systems typically designed with features desired by larger organizations with many resources managing multiple programs and projects. The audience for this work is the small organizations and Agile project teams desiring an inexpensive, simple, user-friendly, task management tool. This work uses standard readily available software, Excel, requiring minimum data entry and automatically creating summary charts and performance data. It is formatted to print out and resemble standard flip charts and provide the visuals associated with this type of work.« less

Functional anatomy of the spine.

PubMed

Bogduk, Nikolai

2016-01-01

Among other important features of the functional anatomy of the spine, described in this chapter, is the remarkable difference between the design and function of the cervical spine and that of the lumbar spine. In the cervical spine, the atlas serves to transmit the load of the head to the typical cervical vertebrae. The axis adapts the suboccipital region to the typical cervical spine. In cervical intervertebrtal discs the anulus fibrosus is not circumferential but is crescentic, and serves as an interosseous ligament in the saddle joint between vertebral bodies. Cervical vertebrae rotate and translate in the sagittal plane, and rotate in the manner of an inverted cone, across an oblique coronal plane. The cervical zygapophysial joints are the most common source of chronic neck pain. By contrast, lumbar discs are well designed to sustain compression loads, but rely on posterior elements to limit axial rotation. Internal disc disruption is the most common basis for chronic low-back pain. Spinal muscles are arranged systematically in prevertebral and postvertebral groups. The intrinsic elements of the spine are innervated by the dorsal rami of the spinal nerves, and by the sinuvertebral nerves. Little modern research has been conducted into the structure of the thoracic spine, or the causes of thoracic spinal pain. © 2016 Elsevier B.V. All rights reserved.

Effects of Vocal Fold Nodules on Glottal Cycle Measurements Derived from High-Speed Videoendoscopy in Children

PubMed Central

2016-01-01

The goal of this study is to quantify the effects of vocal fold nodules on vibratory motion in children using high-speed videoendoscopy. Differences in vibratory motion were evaluated in 20 children with vocal fold nodules (5–11 years) and 20 age and gender matched typically developing children (5–11 years) during sustained phonation at typical pitch and loudness. Normalized kinematic features of vocal fold displacements from the mid-membranous vocal fold point were extracted from the steady-state high-speed video. A total of 12 kinematic features representing spatial and temporal characteristics of vibratory motion were calculated. Average values and standard deviations (cycle-to-cycle variability) of the following kinematic features were computed: normalized peak displacement, normalized average opening velocity, normalized average closing velocity, normalized peak closing velocity, speed quotient, and open quotient. Group differences between children with and without vocal fold nodules were statistically investigated. While a moderate effect size was observed for the spatial feature of speed quotient, and the temporal feature of normalized average closing velocity in children with nodules compared to vocally normal children, none of the features were statistically significant between the groups after Bonferroni correction. The kinematic analysis of the mid-membranous vocal fold displacement revealed that children with nodules primarily differ from typically developing children in closing phase kinematics of the glottal cycle, whereas the opening phase kinematics are similar. Higher speed quotients and similar opening phase velocities suggest greater relative forces are acting on vocal fold in the closing phase. These findings suggest that future large-scale studies should focus on spatial and temporal features related to the closing phase of the glottal cycle for differentiating the kinematics of children with and without vocal fold nodules. PMID:27124157

Understanding of the Geomorphological Elements in Discrimination of Typical Mediterranean Land Cover Types

NASA Astrophysics Data System (ADS)

Elhag, Mohamed; Boteva, Silvena

2017-12-01

Quantification of geomorphometric features is the keystone concern of the current study. The quantification was based on the statistical approach in term of multivariate analysis of local topographic features. The implemented algorithm utilizes the Digital Elevation Model (DEM) to categorize and extract the geomorphometric features embedded in the topographic dataset. The morphological settings were exercised on the central pixel of 3x3 per-defined convolution kernel to evaluate the surrounding pixels under the right directional pour point model (D8) of the azimuth viewpoints. Realization of unsupervised classification algorithm in term of Iterative Self-Organizing Data Analysis Technique (ISODATA) was carried out on ASTER GDEM within the boundary of the designated study area to distinguish 10 morphometric classes. The morphometric classes expressed spatial distribution variation in the study area. The adopted methodology is successful to appreciate the spatial distribution of the geomorphometric features under investigation. The conducted results verified the superimposition of the delineated geomorphometric elements over a given remote sensing imagery to be further analyzed. Robust relationship between different Land Cover types and the geomorphological elements was established in the context of the study area. The domination and the relative association of different Land Cover types in corresponding to its geomorphological elements were demonstrated.

CD 99 immunocytochemistry in solid pseudopapillary tumor of pancreas: A study on fine-needle aspiration cytology smears.

PubMed

Ghosh, Ranajoy; Mallik, Saumya R; Mathur, Sandeep R; Iyer, Venkateswaran K

2013-07-01

Solid pseudopapillary tumor of pancreas (SPTP) is a rare pancreatic tumor of uncertain histogenesis usually affecting young women. Though these tumors have characteristic cytomorphology, it is sometimes difficult to differentiate them from neuroendocrine tumors of the pancreas. We reviewed cases of SPTP to delineate the diagnostic cytological features and also observed utility of CD 99 (MIC 2) immunostaining to aid in the diagnosis of this tumor. This study was designed to demonstrate the utility of CD 99 immunostaining along with cytological features for making a pre-operative diagnosis and delineating it from the neuroendocrine tumor of pancreas which is a close mimic. Cytomorphological features of 11 cases of solid pseudopapillary neoplasm diagnosed by pre-operative fine-needle aspiration cytology (FNAC) at our institute were reviewed. Immunocytochemistry for CD 99 was also performed on the smears. All the cases had cellular smears with monomorphic cells lying singly, as loosely cohesive clusters as well as forming delicate pseudopapillae. Presence of intra and extra-cellular basement membrane material, background foamy macrophages and nuclear grooves were the other salient features. Immunocytochemistry for CD 99 could be performed on eight cases and demonstrated typical paranuclear dot-like positivity. Pre-operative early diagnosis of SPTP can be made by FNAC which can further be aided by CD 99 immunocytochemistry.

Childhood Rituals and Executive Functions

ERIC Educational Resources Information Center

Tregay, Jenifer; Gilmour, Jane; Charman, Tony

2009-01-01

Repetitive and ritualistic behaviours (RRBs) are a feature of both typical and atypical development. While the cognitive correlates of these behaviours have been investigated in some neurodevelopmental conditions these links remain largely unexplored in typical development. The current study examined the relationship between RRBs and executive…

9. Detail of a typical window and a ventilator just ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Detail of a typical window and a ventilator just below the window sill - the only instance of such placement of this feature in the structure. - Perry Township School No. 3, Middle Mount Vernon & Eickhoff Roads, Evansville, Vanderburgh County, IN

Fast Solution in Sparse LDA for Binary Classification

NASA Technical Reports Server (NTRS)

Moghaddam, Baback

2010-01-01

An algorithm that performs sparse linear discriminant analysis (Sparse-LDA) finds near-optimal solutions in far less time than the prior art when specialized to binary classification (of 2 classes). Sparse-LDA is a type of feature- or variable- selection problem with numerous applications in statistics, machine learning, computer vision, computational finance, operations research, and bio-informatics. Because of its combinatorial nature, feature- or variable-selection problems are NP-hard or computationally intractable in cases involving more than 30 variables or features. Therefore, one typically seeks approximate solutions by means of greedy search algorithms. The prior Sparse-LDA algorithm was a greedy algorithm that considered the best variable or feature to add/ delete to/ from its subsets in order to maximally discriminate between multiple classes of data. The present algorithm is designed for the special but prevalent case of 2-class or binary classification (e.g. 1 vs. 0, functioning vs. malfunctioning, or change versus no change). The present algorithm provides near-optimal solutions on large real-world datasets having hundreds or even thousands of variables or features (e.g. selecting the fewest wavelength bands in a hyperspectral sensor to do terrain classification) and does so in typical computation times of minutes as compared to days or weeks as taken by the prior art. Sparse LDA requires solving generalized eigenvalue problems for a large number of variable subsets (represented by the submatrices of the input within-class and between-class covariance matrices). In the general (fullrank) case, the amount of computation scales at least cubically with the number of variables and thus the size of the problems that can be solved is limited accordingly. However, in binary classification, the principal eigenvalues can be found using a special analytic formula, without resorting to costly iterative techniques. The present algorithm exploits this analytic form along with the inherent sequential nature of greedy search itself. Together this enables the use of highly-efficient partitioned-matrix-inverse techniques that result in large speedups of computation in both the forward-selection and backward-elimination stages of greedy algorithms in general.

A Conventional Liner Acoustic/Drag Interaction Benchmark Database

NASA Technical Reports Server (NTRS)

Howerton, Brian M.; Jones, Michael G.

2017-01-01

The aerodynamic drag of acoustic liners has become a significant topic in the design of such for aircraft noise applications. In order to evaluate the benefits of concepts designed to reduce liner drag, it is necessary to establish the baseline performance of liners employing the typical design features of conventional configurations. This paper details a set of experiments in the NASA Langley Grazing Flow Impedance Tube to quantify the relative drag of a number of perforate-over-honeycomb liner configurations at flow speeds of M=0.3 and 0.5. These conventional liners are investigated to determine their resistance factors using a static pressure drop approach. Comparison of the resistance factors gives a relative measurement of liner drag. For these same flow conditions, acoustic measurements are performed with tonal excitation from 400 to 3000 Hz at source sound pressure levels of 140 and 150 dB. Educed impedance and attenuation spectra are used to determine the interaction between acoustic performance and drag.

A Common DPU Platform for ESA JUICE Mission Instruments

NASA Astrophysics Data System (ADS)

Aberg, Martin; Hellstrom, Daniel; Samuelsson, Arne; Torelli, Felice

2016-08-01

This paper describes the resulting hardware and software platform based on GR712RC [1] LEON3-FT that Cobham Gaisler developed in accordance with the common system requirements of the ten scientific instruments on-board the ESA JUICE spacecraft destined the Jupiter system [8].The radiation hardened DPU platform features EDAC protected boot, application memory and working memory of configurable sizes and SpaceWire, FPGA I/O-32/16/8, GPIO, UART and SPI I/O interfaces. The design has undergone PSA, Risk, WCA, Radiation analyses etc. to justify component and design choices resulting in a robust design that can be used in spacecrafts requiring a total dose up to 100krad(Si). The prototype board manufactured uses engineering models of the flight components to ensure that development is representative.Validated boot, standby and driver software accommodates the various DPU platform configurations. The boot performs low-level DPU initialization, standby handles OBC SpaceWire communication and finally the loading and executing of application images typically stored in the non-volatile application memory.

Design of chemical space networks on the basis of Tversky similarity

NASA Astrophysics Data System (ADS)

Wu, Mengjun; Vogt, Martin; Maggiora, Gerald M.; Bajorath, Jürgen

2016-01-01

Chemical space networks (CSNs) have been introduced as a coordinate-free representation of chemical space. In CSNs, nodes represent compounds and edges pairwise similarity relationships. These network representations are mostly used to navigate sections of biologically relevant chemical space. Different types of CSNs have been designed on the basis of alternative similarity measures including continuous numerical similarity values or substructure-based similarity criteria. CSNs can be characterized and compared on the basis of statistical concepts from network science. Herein, a new CSN design is introduced that is based upon asymmetric similarity assessment using the Tversky coefficient and termed TV-CSN. Compared to other CSNs, TV-CSNs have unique features. While CSNs typically contain separate compound communities and exhibit small world character, many TV-CSNs are also scale-free in nature and contain hubs, i.e., extensively connected central compounds. Compared to other CSNs, these hubs are a characteristic of TV-CSN topology. Hub-containing compound communities are of particular interest for the exploration of structure-activity relationships.

Waste receiving and processing plant control system; system design description

DOE Office of Scientific and Technical Information (OSTI.GOV)

LANE, M.P.

1999-02-24

The Plant Control System (PCS) is a heterogeneous computer system composed of numerous sub-systems. The PCS represents every major computer system that is used to support operation of the Waste Receiving and Processing (WRAP) facility. This document, the System Design Description (PCS SDD), includes several chapters and appendices. Each chapter is devoted to a separate PCS sub-system. Typically, each chapter includes an overview description of the system, a list of associated documents related to operation of that system, and a detailed description of relevant system features. Each appendice provides configuration information for selected PCS sub-systems. The appendices are designed asmore » separate sections to assist in maintaining this document due to frequent changes in system configurations. This document is intended to serve as the primary reference for configuration of PCS computer systems. The use of this document is further described in the WRAP System Configuration Management Plan, WMH-350, Section 4.1.« less

Adaptive pattern recognition by mini-max neural networks as a part of an intelligent processor

NASA Technical Reports Server (NTRS)

Szu, Harold H.

1990-01-01

In this decade and progressing into 21st Century, NASA will have missions including Space Station and the Earth related Planet Sciences. To support these missions, a high degree of sophistication in machine automation and an increasing amount of data processing throughput rate are necessary. Meeting these challenges requires intelligent machines, designed to support the necessary automations in a remote space and hazardous environment. There are two approaches to designing these intelligent machines. One of these is the knowledge-based expert system approach, namely AI. The other is a non-rule approach based on parallel and distributed computing for adaptive fault-tolerances, namely Neural or Natural Intelligence (NI). The union of AI and NI is the solution to the problem stated above. The NI segment of this unit extracts features automatically by applying Cauchy simulated annealing to a mini-max cost energy function. The feature discovered by NI can then be passed to the AI system for future processing, and vice versa. This passing increases reliability, for AI can follow the NI formulated algorithm exactly, and can provide the context knowledge base as the constraints of neurocomputing. The mini-max cost function that solves the unknown feature can furthermore give us a top-down architectural design of neural networks by means of Taylor series expansion of the cost function. A typical mini-max cost function consists of the sample variance of each class in the numerator, and separation of the center of each class in the denominator. Thus, when the total cost energy is minimized, the conflicting goals of intraclass clustering and interclass segregation are achieved simultaneously.

Compliant Tactile Sensors

NASA Technical Reports Server (NTRS)

Torres-Jara, Eduardo R.

2011-01-01

Tactile sensors are currently being designed to sense interactions with human hands or pen-like interfaces. They are generally embedded in screens, keyboards, mousepads, and pushbuttons. However, they are not well fitted to sense interactions with all kinds of objects. A novel sensor was originally designed to investigate robotics manipulation where not only the contact with an object needs to be detected, but also where the object needs to be held and manipulated. This tactile sensor has been designed with features that allow it to sense a large variety of objects in human environments. The sensor is capable of detecting forces coming from any direction. As a result, this sensor delivers a force vector with three components. In contrast to most of the tactile sensors that are flat, this one sticks out from the surface so that it is likely to come in contact with objects. The sensor conforms to the object with which it interacts. This augments the contact's surface, consequently reducing the stress applied to the object. This feature makes the sensor ideal for grabbing objects and other applications that require compliance with objects. The operational range of the sensor allows it to operate well with objects found in peoples' daily life. The fabrication of this sensor is simple and inexpensive because of its compact mechanical configuration and reduced electronics. These features are convenient for mass production of individual sensors as well as dense arrays. The biologically inspired tactile sensor is sensitive to both normal and lateral forces, providing better feedback to the host robot about the object to be grabbed. It has a high sensitivity, enabling its use in manipulation fingers, which typically have low mechanical impedance in order to be very compliant. The construction of the sensor is simple, using inexpensive technologies like silicon rubber molding and standard stock electronics.

High throughput parallel backside contacting and periodic texturing for high-efficiency solar cells

DOEpatents

Daniel, Claus; Blue, Craig A.; Ott, Ronald D.

2014-08-19

Disclosed are configurations of long-range ordered features of solar cell materials, and methods for forming same. Some features include electrical access openings through a backing layer to a photovoltaic material in the solar cell. Some features include textured features disposed adjacent a surface of a solar cell material. Typically the long-range ordered features are formed by ablating the solar cell material with a laser interference pattern from at least two laser beams.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, T.; Curtis, O.; Stephenson, R.

As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta-based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA, in the mixed humid climate. This home serves as a residence and home office for the firm's owners, as well as a demonstration of their design approach to potential and current clients. Southface believes the home demonstrates current best practices for the mixed-humid climate, including a building envelope featuring advanced air sealing details and low density spray foam insulation, glazing that exceeds ENERGY STARmore » requirements, and a high performance heating and cooling system. Construction quality and execution was a high priority for TaC Studios and was ensured by a third party review process. Post-construction testing showed that the project met stated goals for envelope performance, an air infiltration rate of 2.15 ACH50. The homeowners wished to further validate whole house energy savings through the project's involvement with Building America and this long-term monitoring effort. As a Building America test home, this home was evaluated to detail whole house energy use, end use loads, and the efficiency and operation of the ground source heat pump and associated systems. Given that the home includes many non-typical end use loads including a home office, pool, landscape water feature, and other luxury features not accounted for in Building America modeling tools, these end uses were separately monitored to determine their impact on overall energy consumption.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, T.; Curtis, O.; Stephenson, R.

As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta-based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA in the mixed humid climate. This home serves as a residence and home office for the firm's owners, as well as a demonstration of their design approach topotential and current clients. Southface believes the home demonstrates current best practices for the mixed-humid climate, including a building envelope featuring advanced air sealing details and low density spray foam insulation, glazing that exceeds ENERGY STAR requirements,more » and a high performance heating and cooling system. Construction quality and execution was a high priority for TaCStudios and was ensured by a third party review process. Post-construction testing showed that the project met stated goals for envelope performance, an air infiltration rate of 2.15 ACH50. The homeowners wished to further validate whole house energy savings through the project's involvement with Building America and this long-term monitoring effort. As a Building America test home, this homewas evaluated to detail whole house energy use, end use loads, and the efficiency and operation of the ground source heat pump and associated systems. Given that the home includes many non-typical end use loads including a home office, pool, landscape water feature, and other luxury features not accounted for in Building America modeling tools, these end uses were separately monitored todetermine their impact on overall energy consumption.« less

Symmetric corticobasal degeneration (S-CBD).

PubMed

Hassan, Anhar; Whitwell, Jennifer L; Boeve, Bradley F; Jack, Clifford R; Parisi, Joseph E; Dickson, Dennis W; Josephs, Keith A

2010-03-01

Corticobasal degeneration (CBD) is a neurodegenerative disease characterized pathologically by neuronal loss, gliosis and tau deposition in neocortex, basal ganglia and brainstem. Typical clinical presentation is known as corticobasal syndrome (CBS) and involves the core features of progressive asymmetric rigidity and apraxia, accompanied by other signs of cortical and extrapyramidal dysfunction. Asymmetry is also emphasized on neuroimaging. To describe a series of cases of CBD with symmetric clinical features and to compare clinical and imaging features of these symmetric CBD cases (S-CBD) to typical cases of CBS with CBD pathology. All cases of pathologically confirmed CBD from the Mayo Clinic Rochester database were identified. Clinical records were reviewed and quantitative volumetric analysis of symmetric atrophy on head MRI using atlas based parcellation was performed. Subjects were classified as S-CBD if no differences had been observed between right- and left-sided cortical or extrapyramidal signs or symptoms. S-CBD cases were compared to 10 randomly selected typical CBS cases. Five cases (2 female) met criteria for S-CBD. None had limb dystonia, myoclonus, apraxia or alien limb phenomena. S-CBD cases had significantly less asymmetric atrophy when compared with CBS cases (p=0.009); they were also younger at onset (median 61 versus 66 years, p<0.05) and death (67 versus 73 years, p<0.05). Family history was present in 40% of S-CBD cases. CBD can have a symmetric presentation, clinically and radiologically, in which typical features of CBS, such as limb apraxia, myoclonus, dystonia and alien limb phenomenon, may be absent. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Sparse Coding for N-Gram Feature Extraction and Training for File Fragment Classification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Felix; Quach, Tu-Thach; Wheeler, Jason

File fragment classification is an important step in the task of file carving in digital forensics. In file carving, files must be reconstructed based on their content as a result of their fragmented storage on disk or in memory. Existing methods for classification of file fragments typically use hand-engineered features such as byte histograms or entropy measures. In this paper, we propose an approach using sparse coding that enables automated feature extraction. Sparse coding, or sparse dictionary learning, is an unsupervised learning algorithm, and is capable of extracting features based simply on how well those features can be used tomore » reconstruct the original data. With respect to file fragments, we learn sparse dictionaries for n-grams, continuous sequences of bytes, of different sizes. These dictionaries may then be used to estimate n-gram frequencies for a given file fragment, but for significantly larger n-gram sizes than are typically found in existing methods which suffer from combinatorial explosion. To demonstrate the capability of our sparse coding approach, we used the resulting features to train standard classifiers such as support vector machines (SVMs) over multiple file types. Experimentally, we achieved significantly better classification results with respect to existing methods, especially when the features were used in supplement to existing hand-engineered features.« less

Sparse Coding for N-Gram Feature Extraction and Training for File Fragment Classification

DOE PAGES

Wang, Felix; Quach, Tu-Thach; Wheeler, Jason; ...

2018-04-05

File fragment classification is an important step in the task of file carving in digital forensics. In file carving, files must be reconstructed based on their content as a result of their fragmented storage on disk or in memory. Existing methods for classification of file fragments typically use hand-engineered features such as byte histograms or entropy measures. In this paper, we propose an approach using sparse coding that enables automated feature extraction. Sparse coding, or sparse dictionary learning, is an unsupervised learning algorithm, and is capable of extracting features based simply on how well those features can be used tomore » reconstruct the original data. With respect to file fragments, we learn sparse dictionaries for n-grams, continuous sequences of bytes, of different sizes. These dictionaries may then be used to estimate n-gram frequencies for a given file fragment, but for significantly larger n-gram sizes than are typically found in existing methods which suffer from combinatorial explosion. To demonstrate the capability of our sparse coding approach, we used the resulting features to train standard classifiers such as support vector machines (SVMs) over multiple file types. Experimentally, we achieved significantly better classification results with respect to existing methods, especially when the features were used in supplement to existing hand-engineered features.« less

Atypical development of configural face recognition in children with autism, Down syndrome and Williams syndrome.

PubMed

Dimitriou, D; Leonard, H C; Karmiloff-Smith, A; Johnson, M H; Thomas, M S C

2015-05-01

Configural processing in face recognition is a sensitivity to the spacing between facial features. It has been argued both that its presence represents a high level of expertise in face recognition, and also that it is a developmentally vulnerable process. We report a cross-syndrome investigation of the development of configural face recognition in school-aged children with autism, Down syndrome and Williams syndrome compared with a typically developing comparison group. Cross-sectional trajectory analyses were used to compare configural and featural face recognition utilising the 'Jane faces' task. Trajectories were constructed linking featural and configural performance either to chronological age or to different measures of mental age (receptive vocabulary, visuospatial construction), as well as the Benton face recognition task. An emergent inversion effect across age for detecting configural but not featural changes in faces was established as the marker of typical development. Children from clinical groups displayed atypical profiles that differed across all groups. We discuss the implications for the nature of face processing within the respective developmental disorders, and how the cross-sectional syndrome comparison informs the constraints that shape the typical development of face recognition. © 2014 MENCAP and International Association of the Scientific Study of Intellectual and Developmental Disabilities and John Wiley & Sons Ltd.

[Report of a case with Joubert syndrome and literature review].

PubMed

Yi, Ya-hui; Li, Gang; Lu, Zhong-lie; Zhou, Jian-sheng; Yao, Zhen-wei; Wang, Peng-fei; Yao, Jin-xiang

2011-12-01

To explore the clinical feature, imaging and their diagnostic value for Joubert syndrome (JS). The clinical data, imaging feature, and 31 references from China Biomedical literature database (CBMdise) were reviewed and analyzed. The age of onset of 32 patients including male 20 and female 12 ranged from 3 days to 6 years (mean 2.2 years). All the 32 patients with Joubert syndrome showed "slow growth" and "reduced muscle tension", 26 cases (81.3%) showed "gasp for breath", 26 cases (81.3%) showed "unusual motion of eyeball", 2 cases (6.3%) showed additional fingers (toes), 6 cases (18.8%) showed stretching tongue with agape. The typical imaging features of Joubert syndrome included "molar tooth sign", "midline cleavage" between cerebellar hemispheres and "bat-wing" like fourth ventricle, all the 32 patients with Joubert syndrome showed "midline cleavage", "molar tooth sign" was present in 29 cases (90.1%), and "bat-wing" like fourth ventricle in 30 cases (93.8%). Joubert syndrome is a rare congenital brain malformation. The typical clinical manifestations included "gasp for breath", "reduced tension of muscle", "slow growth" and "unusual motion of eyeball", and at the same time the patients had the following typical imaging features of brain: "molar tooth sign", "midline cleavage" and "bat-wing" like fourth ventricle.

The Target of the Question: A Taxonomy of Textual Features for Cambridge University "O" Levels English

ERIC Educational Resources Information Center

Benjamin, Shanti Isabelle

2015-01-01

This study investigates the typical textual features that are most frequently targeted in short-answer reading comprehension questions of the Cambridge University "O" Level English Paper 2. Test writers' awareness of how textual features impact on understanding of meanings in text decisions will determine to great extent their decisions…

Piloted simulation of one-on-one helicopter air combat at NOE flight levels

NASA Technical Reports Server (NTRS)

Lewis, M. S.; Aiken, E. W.

1985-01-01

A piloted simulation designed to examine the effects of terrain proximity and control system design on helicopter performance during one-on-one air combat maneuvering (ACM) is discussed. The NASA Ames vertical motion simulator (VMS) and the computer generated imagery (CGI) systems were modified to allow two aircraft to be independently piloted on a single CGI data base. Engagements were begun with the blue aircraft already in a tail-chase position behind the red, and also with the two aircraft originating from positions unknown to each other. Maneuvering was very aggressive and safety requirements for minimum altitude, separation, and maximum bank angles typical of flight test were not used. Results indicate that the presence of terrain features adds an order of complexiaty to the task performed over clear air ACM and that mix of attitude and rate command-type stability and control augmentation system (SCAS) design may be desirable. The simulation system design, the flight paths flown, and the tactics used were compared favorably by the evaluation pilots to actual flight test experiments.

Model, analysis, and evaluation of the effects of analog VLSI arithmetic on linear subspace-based image recognition.

PubMed

Carvajal, Gonzalo; Figueroa, Miguel

2014-07-01

Typical image recognition systems operate in two stages: feature extraction to reduce the dimensionality of the input space, and classification based on the extracted features. Analog Very Large Scale Integration (VLSI) is an attractive technology to achieve compact and low-power implementations of these computationally intensive tasks for portable embedded devices. However, device mismatch limits the resolution of the circuits fabricated with this technology. Traditional layout techniques to reduce the mismatch aim to increase the resolution at the transistor level, without considering the intended application. Relating mismatch parameters to specific effects in the application level would allow designers to apply focalized mismatch compensation techniques according to predefined performance/cost tradeoffs. This paper models, analyzes, and evaluates the effects of mismatched analog arithmetic in both feature extraction and classification circuits. For the feature extraction, we propose analog adaptive linear combiners with on-chip learning for both Least Mean Square (LMS) and Generalized Hebbian Algorithm (GHA). Using mathematical abstractions of analog circuits, we identify mismatch parameters that are naturally compensated during the learning process, and propose cost-effective guidelines to reduce the effect of the rest. For the classification, we derive analog models for the circuits necessary to implement Nearest Neighbor (NN) approach and Radial Basis Function (RBF) networks, and use them to emulate analog classifiers with standard databases of face and hand-writing digits. Formal analysis and experiments show how we can exploit adaptive structures and properties of the input space to compensate the effects of device mismatch at the application level, thus reducing the design overhead of traditional layout techniques. Results are also directly extensible to multiple application domains using linear subspace methods. Copyright © 2014 Elsevier Ltd. All rights reserved.

From Petascale to Exascale: Eight Focus Areas of R&D Challenges for HPC Simulation Environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springmeyer, R; Still, C; Schulz, M

2011-03-17

Programming models bridge the gap between the underlying hardware architecture and the supporting layers of software available to applications. Programming models are different from both programming languages and application programming interfaces (APIs). Specifically, a programming model is an abstraction of the underlying computer system that allows for the expression of both algorithms and data structures. In comparison, languages and APIs provide implementations of these abstractions and allow the algorithms and data structures to be put into practice - a programming model exists independently of the choice of both the programming language and the supporting APIs. Programming models are typically focusedmore » on achieving increased developer productivity, performance, and portability to other system designs. The rapidly changing nature of processor architectures and the complexity of designing an exascale platform provide significant challenges for these goals. Several other factors are likely to impact the design of future programming models. In particular, the representation and management of increasing levels of parallelism, concurrency and memory hierarchies, combined with the ability to maintain a progressive level of interoperability with today's applications are of significant concern. Overall the design of a programming model is inherently tied not only to the underlying hardware architecture, but also to the requirements of applications and libraries including data analysis, visualization, and uncertainty quantification. Furthermore, the successful implementation of a programming model is dependent on exposed features of the runtime software layers and features of the operating system. Successful use of a programming model also requires effective presentation to the software developer within the context of traditional and new software development tools. Consideration must also be given to the impact of programming models on both languages and the associated compiler infrastructure. Exascale programming models must reflect several, often competing, design goals. These design goals include desirable features such as abstraction and separation of concerns. However, some aspects are unique to large-scale computing. For example, interoperability and composability with existing implementations will prove critical. In particular, performance is the essential underlying goal for large-scale systems. A key evaluation metric for exascale models will be the extent to which they support these goals rather than merely enable them.« less

SVGenes: a library for rendering genomic features in scalable vector graphic format.

PubMed

Etherington, Graham J; MacLean, Daniel

2013-08-01

Drawing genomic features in attractive and informative ways is a key task in visualization of genomics data. Scalable Vector Graphics (SVG) format is a modern and flexible open standard that provides advanced features including modular graphic design, advanced web interactivity and animation within a suitable client. SVGs do not suffer from loss of image quality on re-scaling and provide the ability to edit individual elements of a graphic on the whole object level independent of the whole image. These features make SVG a potentially useful format for the preparation of publication quality figures including genomic objects such as genes or sequencing coverage and for web applications that require rich user-interaction with the graphical elements. SVGenes is a Ruby-language library that uses SVG primitives to render typical genomic glyphs through a simple and flexible Ruby interface. The library implements a simple Page object that spaces and contains horizontal Track objects that in turn style, colour and positions features within them. Tracks are the level at which visual information is supplied providing the full styling capability of the SVG standard. Genomic entities like genes, transcripts and histograms are modelled in Glyph objects that are attached to a track and take advantage of SVG primitives to render the genomic features in a track as any of a selection of defined glyphs. The feature model within SVGenes is simple but flexible and not dependent on particular existing gene feature formats meaning graphics for any existing datasets can easily be created without need for conversion. The library is provided as a Ruby Gem from https://rubygems.org/gems/bio-svgenes under the MIT license, and open source code is available at https://github.com/danmaclean/bioruby-svgenes also under the MIT License. dan.maclean@tsl.ac.uk.

Does Whole-Word Multimedia Software Support Literacy Acquisition?

ERIC Educational Resources Information Center

Karemaker, Arjette M.; Pitchford, Nicola J.; O'Malley, Claire

2010-01-01

This study examined the extent to which multimedia features of typical literacy learning software provide added benefits for developing literacy skills compared with typical whole-class teaching methods. The effectiveness of the multimedia software Oxford Reading Tree (ORT) for Clicker in supporting early literacy acquisition was investigated…

Designing ternary blend bulk heterojunction solar cells with reduced carrier recombination and a fill factor of 77%

NASA Astrophysics Data System (ADS)

Gasparini, Nicola; Jiao, Xuechen; Heumueller, Thomas; Baran, Derya; Matt, Gebhard J.; Fladischer, Stefanie; Spiecker, Erdmann; Ade, Harald; Brabec, Christoph J.; Ameri, Tayebeh

2016-09-01

In recent years the concept of ternary blend bulk heterojunction (BHJ) solar cells based on organic semiconductors has been widely used to achieve a better match to the solar irradiance spectrum, and power conversion efficiencies beyond 10% have been reported. However, the fill factor of organic solar cells is still limited by the competition between recombination and extraction of free charges. Here, we design advanced material composites leading to a high fill factor of 77% in ternary blends, thus demonstrating how the recombination thresholds can be overcome. Extending beyond the typical sensitization concept, we add a highly ordered polymer that, in addition to enhanced absorption, overcomes limits predicted by classical recombination models. An effective charge transfer from the disordered host system onto the highly ordered sensitizer effectively avoids traps of the host matrix and features an almost ideal recombination behaviour.

Process Upsets Involving Trace Contaminant Control Systems

NASA Technical Reports Server (NTRS)

Graf, John C.; Perry, Jay; Wright, John; Bahr, Jim

2000-01-01

Paradoxically, trace contaminant control systems that suffer unexpected upsets and malfunctions can release hazardous gaseous contaminants into a spacecraft cabin atmosphere causing potentially serious toxicological problems. Trace contaminant control systems designed for spaceflight typically employ a combination of adsorption beds and catalytic oxidation reactors to remove organic and inorganic trace contaminants from the cabin atmosphere. Interestingly, the same design features and attributes which make these systems so effective for purifying a spacecraft's atmosphere can also make them susceptible to system upsets. Cabin conditions can be contributing causes of phenomena such as adsorbent "rollover" and catalyst poisoning can alter a systems performance and in some in stances release contamination into the cabin. Evidence of these phenomena has been observed both in flight and during ground-based tests. The following discussion describes specific instances of system upsets found in trace contaminant control systems, groups these specific upsets into general hazard classifications, and recommends ways to minimize these hazards.

CARES/Life Used for Probabilistic Characterization of MEMS Pressure Sensor Membranes

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.

2002-01-01

Microelectromechanical systems (MEMS) devices are typically made from brittle materials such as silicon using traditional semiconductor manufacturing techniques. They can be etched (or micromachined) from larger structures or can be built up with material deposition processes. Maintaining dimensional control and consistent mechanical properties is considerably more difficult for MEMS because feature size is on the micrometer scale. Therefore, the application of probabilistic design methodology becomes necessary for MEMS. This was demonstrated at the NASA Glenn Research Center and Case Western Reserve University in an investigation that used the NASA-developed CARES/Life brittle material design program to study the probabilistic fracture strength behavior of single-crystal SiC, polycrystalline SiC, and amorphous Si3N4 pressurized 1-mm-square thin-film diaphragms. These materials are of interest because of their superior high-temperature characteristics, which are desirable for harsh environment applications such as turbine engine and rocket propulsion system hot sections.

What young people want from a sexual health website: design and development of Sexunzipped.

PubMed

McCarthy, Ona; Carswell, Kenneth; Murray, Elizabeth; Free, Caroline; Stevenson, Fiona; Bailey, Julia V

2012-10-12

Sexual health education in the United Kingdom is of variable quality, typically focusing on the biological aspects of sex rather than on communication, relationships, and sexual pleasure. The Internet offers a unique opportunity to provide sexual health education to young people, since they can be difficult to engage but frequently use the Internet as a health information resource. To explore through qualitative research young people's views on what elements of a sexual health website would be appealing and engaging, and their views on the content, design, and interactive features of the Sexunzipped intervention website. We recruited 67 young people aged 16-22 years in London, UK. We held 21 focus groups and 6 one-to-one interviews to establish sexual health priorities, views on website look and feel, and what features of a sexual heath website would attract and engage them. Two researchers facilitated the focus groups, using a semistructured topic guide to lead the discussions and asking open questions to elicit a range of views. The discussions and interviews were audio recorded and detailed notes were made on key topics from the audio recording. Young people's views influenced design templates for the content and interactive features of Sexunzipped. Young people particularly wanted straightforward information on sexual pleasure, sexually transmitted infections and pregnancy, how to communicate with partners, how to develop skills in giving pleasure, and emotions involved in sex and relationships. Focus group participants wanted social interaction with other young people online and wanted to see themselves reflected in some way such as through images or videos. While it is challenging to meet all of young people's technological and design requirements, consultation with the target audience is valuable and necessary in developing an online sexual health intervention. Young people are willing to talk about sensitive issues, enjoy the discussions, and can offer key insights that influence intervention development.

What Young People Want From a Sexual Health Website: Design and Development of Sexunzipped

PubMed Central

Carswell, Kenneth; Murray, Elizabeth; Free, Caroline; Stevenson, Fiona; Bailey, Julia V

2012-01-01

Background Sexual health education in the United Kingdom is of variable quality, typically focusing on the biological aspects of sex rather than on communication, relationships, and sexual pleasure. The Internet offers a unique opportunity to provide sexual health education to young people, since they can be difficult to engage but frequently use the Internet as a health information resource. Objectives To explore through qualitative research young people’s views on what elements of a sexual health website would be appealing and engaging, and their views on the content, design, and interactive features of the Sexunzipped intervention website. Methods We recruited 67 young people aged 16–22 years in London, UK. We held 21 focus groups and 6 one-to-one interviews to establish sexual health priorities, views on website look and feel, and what features of a sexual heath website would attract and engage them. Two researchers facilitated the focus groups, using a semistructured topic guide to lead the discussions and asking open questions to elicit a range of views. The discussions and interviews were audio recorded and detailed notes were made on key topics from the audio recording. Young people’s views influenced design templates for the content and interactive features of Sexunzipped. Results Young people particularly wanted straightforward information on sexual pleasure, sexually transmitted infections and pregnancy, how to communicate with partners, how to develop skills in giving pleasure, and emotions involved in sex and relationships. Focus group participants wanted social interaction with other young people online and wanted to see themselves reflected in some way such as through images or videos. Conclusions While it is challenging to meet all of young people’s technological and design requirements, consultation with the target audience is valuable and necessary in developing an online sexual health intervention. Young people are willing to talk about sensitive issues, enjoy the discussions, and can offer key insights that influence intervention development. PMID:23060424

Using pedagogical discipline representations (PDRs) to enable Astro 101 students to reason about modern astrophysics

NASA Astrophysics Data System (ADS)

Wallace, Colin Scott; Prather, Edward E.; Chambers, Timothy G.; Kamenetzky, Julia R.; Hornstein, Seth D.

2017-01-01

Instructors of introductory, college-level, general education astronomy (Astro 101) often want to include topics from the cutting-edge of modern astrophysics in their course. Unfortunately, the teaching of these cutting-edge topics is typically confined to advanced undergraduate or graduate classes, using representations (graphical, mathematical, etc.) that are inaccessible to the vast majority of Astro 101 students. Consequently, many Astro 101 instructors feel that they have no choice but to cover these modern topics at a superficial level. Pedagogical discipline representations (PDRs) are one solution to this problem. Pedagogical discipline representations are representations that are explicitly designed to enhance the teaching and learning of a topic, even though these representations may not typically be found in traditional textbooks or used by experts in the discipline who are engaged in topic-specific discourse. In some cases, PDRs are significantly simplified or altered versions of typical discipline representations (graphs, data tables, etc.); in others they may be novel and highly contextualized representations with unique features that purposefully engage novice learners’ pre-existing mental models and reasoning difficulties, facilitating critical discourse. In this talk, I will discuss important lessons that my colleagues and I have learned while developing PDRs and describe how PDRs can enable students to reason about complex modern astrophysical topics.

Range 7 Scanner Integration with PaR Robot Scanning System

NASA Technical Reports Server (NTRS)

Schuler, Jason; Burns, Bradley; Carlson, Jeffrey; Minich, Mark

2011-01-01

An interface bracket and coordinate transformation matrices were designed to allow the Range 7 scanner to be mounted on the PaR Robot detector arm for scanning the heat shield or other object placed in the test cell. A process was designed for using Rapid Form XOR to stitch data from multiple scans together to provide an accurate 3D model of the object scanned. An accurate model was required for the design and verification of an existing heat shield. The large physical size and complex shape of the heat shield does not allow for direct measurement of certain features in relation to other features. Any imaging devices capable of imaging the entire heat shield in its entirety suffers a reduced resolution and cannot image sections that are blocked from view. Prior methods involved tools such as commercial measurement arms, taking images with cameras, then performing manual measurements. These prior methods were tedious and could not provide a 3D model of the object being scanned, and were typically limited to a few tens of measurement points at prominent locations. Integration of the scanner with the robot allows for large complex objects to be scanned at high resolution, and for 3D Computer Aided Design (CAD) models to be generated for verification of items to the original design, and to generate models of previously undocumented items. The main components are the mounting bracket for the scanner to the robot and the coordinate transformation matrices used for stitching the scanner data into a 3D model. The steps involve mounting the interface bracket to the robot's detector arm, mounting the scanner to the bracket, and then scanning sections of the object and recording the location of the tool tip (in this case the center of the scanner's focal point). A novel feature is the ability to stitch images together by coordinates instead of requiring each scan data set to have overlapping identifiable features. This setup allows models of complex objects to be developed even if the object is large and featureless, or has sections that don't have visibility to other parts of the object for use as a reference. In addition, millions of points can be used for creation of an accurate model [i.e. within 0.03 in. (=0.8 mm) over a span of 250 in. (=635 mm)].

Impact of Hearing Aid Technology on Outcomes in Daily Life I: the Patients’ Perspective

PubMed Central

Cox, Robyn M; Johnson, Jani A; Xu, Jingjing

2016-01-01

Objectives One of the challenges facing hearing care providers when recommending hearing aids is the choice of device technology level. Major manufacturers market families of hearing aids that are described as spanning the range from basic technology to premium technology. Premium technology hearing aids include acoustical processing capabilities (features) that are not found in basic technology instruments. These premium features are intended to yield improved hearing in daily life compared to basic-feature devices. However, independent research that establishes the incremental effectiveness of premium-feature devices compared to basic-feature devices is lacking. This research was designed to explore reported differences in hearing abilities for adults using premium-feature and basic-feature hearing aids in their daily lives. Design This was a single-blinded, repeated, crossover trial in which the participants were blinded. All procedures were carefully controlled to limit researcher bias. Forty-five participants used carefully fitted bilateral hearing aids for one month and then provided data to describe the hearing improvements or deficiencies noted in daily life. Typical participants were 70 years old with mild to moderate adult-onset hearing loss bilaterally. Each participant used 4 pairs of hearing aids: premium- and basic-feature devices from brands marketed by each of two major manufacturers. Participants were blinded about the devices they used and about the research questions. Results All of the outcomes were designed to capture the participant’s point of view about the benefits of the hearing aids. Three types of data were collected: change in hearing-related quality of life, extent of agreement with six positively worded statements about everyday hearing with the hearing aids, and reported preferences between the premium- and basic-feature devices from each brand as well as across all four research hearing aids combined. None of these measures yielded a statistically significant difference in outcomes between premium- and basic-feature devices. Participants did not report better outcomes with premium processing with any measure. Conclusions It could reasonably be asserted that the patient’s perspective is the gold standard for hearing aid effectiveness. While the acoustical processing provided by premium features can potentially improve scores on tests conducted in contrived conditions in a laboratory, or on specific items in a questionnaire, this does not ensure that the processing will be of noteworthy benefit when the hearing aid is used in the real world challenges faced by the patient. If evidence suggests the patient cannot detect that premium features yield improvements over basic features in daily life, what is the responsibility of the provider in recommending hearing aid technology level? In the current research, there was no evidence to suggest that premium-feature devices yielded better outcomes than basic-feature devices from the patient’s point of view. All of the research hearing aids were substantially, but equally, helpful. Further research is needed on this topic with other hearing aids and other manufacturers. In the meantime, providers should insist on scientifically credible independent evidence to support effectiveness claims for any hearing help devices. PMID:26881981

Personalized Offline and Pseudo-Online BCI Models to Detect Pedaling Intent

PubMed Central

Rodríguez-Ugarte, Marisol; Iáñez, Eduardo; Ortíz, Mario; Azorín, Jose M.

2017-01-01

The aim of this work was to design a personalized BCI model to detect pedaling intention through EEG signals. The approach sought to select the best among many possible BCI models for each subject. The choice was between different processing windows, feature extraction algorithms and electrode configurations. Moreover, data was analyzed offline and pseudo-online (in a way suitable for real-time applications), with a preference for the latter case. A process for selecting the best BCI model was described in detail. Results for the pseudo-online processing with the best BCI model of each subject were on average 76.7% of true positive rate, 4.94 false positives per minute and 55.1% of accuracy. The personalized BCI model approach was also found to be significantly advantageous when compared to the typical approach of using a fixed feature extraction algorithm and electrode configuration. The resulting approach could be used to more robustly interface with lower limb exoskeletons in the context of the rehabilitation of stroke patients. PMID:28744212

Personalized Offline and Pseudo-Online BCI Models to Detect Pedaling Intent.

PubMed

Rodríguez-Ugarte, Marisol; Iáñez, Eduardo; Ortíz, Mario; Azorín, Jose M

2017-01-01

The aim of this work was to design a personalized BCI model to detect pedaling intention through EEG signals. The approach sought to select the best among many possible BCI models for each subject. The choice was between different processing windows, feature extraction algorithms and electrode configurations. Moreover, data was analyzed offline and pseudo-online (in a way suitable for real-time applications), with a preference for the latter case. A process for selecting the best BCI model was described in detail. Results for the pseudo-online processing with the best BCI model of each subject were on average 76.7% of true positive rate, 4.94 false positives per minute and 55.1% of accuracy. The personalized BCI model approach was also found to be significantly advantageous when compared to the typical approach of using a fixed feature extraction algorithm and electrode configuration. The resulting approach could be used to more robustly interface with lower limb exoskeletons in the context of the rehabilitation of stroke patients.

Probabilistic risk analysis of building contamination.

PubMed

Bolster, D T; Tartakovsky, D M

2008-10-01

We present a general framework for probabilistic risk assessment (PRA) of building contamination. PRA provides a powerful tool for the rigorous quantification of risk in contamination of building spaces. A typical PRA starts by identifying relevant components of a system (e.g. ventilation system components, potential sources of contaminants, remediation methods) and proceeds by using available information and statistical inference to estimate the probabilities of their failure. These probabilities are then combined by means of fault-tree analyses to yield probabilistic estimates of the risk of system failure (e.g. building contamination). A sensitivity study of PRAs can identify features and potential problems that need to be addressed with the most urgency. Often PRAs are amenable to approximations, which can significantly simplify the approach. All these features of PRA are presented in this paper via a simple illustrative example, which can be built upon in further studies. The tool presented here can be used to design and maintain adequate ventilation systems to minimize exposure of occupants to contaminants.

"Murder-suicide" or "murder-accident"? Difficulties with the analysis of cases.

PubMed

Byard, Roger W; Veldhoen, David; Kobus, Hilton; Heath, Karen

2010-09-01

Homicide where a perpetrator is found dead adjacent to the victim usually represents murder-suicide. Two incidents are reported to demonstrate characteristic features in one, and alternative features in the other, that indicate differences in the manner of death. (i) A 37-year-old mother was found dead in a burnt out house with her two young sons in an adjacent bedroom. Deaths were due to incineration and inhalation of products of combustion. (ii) A 39-year-old woman was found stabbed to death in a burnt out house with her 39-year-old de facto partner deceased from the combined effects of incineration and inhalation of products of combustion. The first incident represented a typical murder-suicide, however, in the second incident, the perpetrator had tried to escape through a window and had then sought refuge in a bathroom under a running shower. Murder-accident rather than murder-suicide may therefore be a more accurate designation for such cases. © 2010 American Academy of Forensic Sciences.

Face inversion effects in autism: a combined looking time and pupillometric study.

PubMed

Falck-Ytter, Terje

2008-10-01

Previous research has found that in typically developing individuals, behavioral performance declines and electrophysiological brain responses are altered when the face is inverted. Such effects are generally attributed to disruption of configural information. Individuals with autism spectrum disorder (ASD) have been found to show less pronounced inversion effects, a result in line with the view that featural processing of faces is enhanced in ASD. No study has determined if, or how, such local bias is reflected in the eye movements used in face observation. In this eye tracking study, looking time and pupil dilation were investigated during the presentation of upright and inverted faces in preschool children with ASD and typically developing preschoolers. On average, both children with ASD and typically developing children looked less at the face and the eye areas during inverted presentations than during upright presentations. Nevertheless, individuals with ASD had a stronger tendency than typically developing children to look at the same face features during upright and inverted presentations, which is suggestive of a local bias. Pupil dilation, reflecting increased processing load, was larger for inverted than upright faces in the ASD group only, and pupillary inversion effects were stronger in ASD than in typically developing children.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lai, Jih-Sheng

This paper introduces control system design based softwares, SIMNON and MATLAB/SIMULINK, for power electronics system simulation. A complete power electronics system typically consists of a rectifier bridge along with its smoothing capacitor, an inverter, and a motor. The system components, featuring discrete or continuous, linear or nonlinear, are modeled in mathematical equations. Inverter control methods,such as pulse-width-modulation and hysteresis current control, are expressed in either computer algorithms or digital circuits. After describing component models and control methods, computer programs are then developed for complete systems simulation. Simulation results are mainly used for studying system performances, such as input and outputmore » current harmonics, torque ripples, and speed responses. Key computer programs and simulation results are demonstrated for educational purposes.« less

HEP - A semaphore-synchronized multiprocessor with central control. [Heterogeneous Element Processor

NASA Technical Reports Server (NTRS)

Gilliland, M. C.; Smith, B. J.; Calvert, W.

1976-01-01

The paper describes the design concept of the Heterogeneous Element Processor (HEP), a system tailored to the special needs of scientific simulation. In order to achieve high-speed computation required by simulation, HEP features a hierarchy of processes executing in parallel on a number of processors, with synchronization being largely accomplished by hardware. A full-empty-reserve scheme of synchronization is realized by zero-one-valued hardware semaphores. A typical system has, besides the control computer and the scheduler, an algebraic module, a memory module, a first-in first-out (FIFO) module, an integrator module, and an I/O module. The architecture of the scheduler and the algebraic module is examined in detail.

[A magnetic therapy apparatus with an adaptable electromagnetic spectrum for the treatment of prostatitis and gynecopathies].

PubMed

Kuz'min, A A; Meshkovskiĭ, D V; Filist, S A

2008-01-01

Problems of engineering and algorithm development of magnetic therapy apparatuses with pseudo-random radiation spectrum within the audio range for treatment of prostatitis and gynecopathies are considered. A typical design based on a PIC 16F microcontroller is suggested. It includes a keyboard, LCD indicator, audio amplifier, inducer, and software units. The problem of pseudo-random signal generation within the audio range is considered. A series of rectangular pulses is generated on a random-length interval on the basis of a three-component random vector. This series provides the required spectral characteristics of the therapeutic magnetic field and their adaptation to the therapeutic conditions and individual features of the patient.

Solar Power Satellite (SPS) fiber optic link assessment

NASA Technical Reports Server (NTRS)

1980-01-01

A feasibility demonstration of a 980 MHz fiber optic link for the Solar Power Satellite (SPS) phase reference distribution system was accomplished. A dual fiber-optic link suitable for a phase distribution frequency of 980 MHz was built and tested. The major link components include single mode injection laser diodes, avalanche photodiodes, and multimode high bandwidth fibers. Signal throughput was demonstrated to be stable and of high quality in all cases. For a typical SPS link length of 200 meters, the transmitted phase at 980 MHz varies approximately 2.5 degrees for every deg C of fiber temperature change. This rate is acceptable because of the link length compensation feature of the phase control design.

Electrical and optical 3D modelling of light-trapping single-photon avalanche diode

NASA Astrophysics Data System (ADS)

Zheng, Tianzhe; Zang, Kai; Morea, Matthew; Xue, Muyu; Lu, Ching-Ying; Jiang, Xiao; Zhang, Qiang; Kamins, Theodore I.; Harris, James S.

2018-02-01

Single-photon avalanche diodes (SPADs) have been widely used to push the frontier of scientific research (e.g., quantum science and single-molecule fluorescence) and practical applications (e.g., Lidar). However, there is a typical compromise between photon detection efficiency and jitter distribution. The light-trapping SPAD has been proposed to break this trade-off by coupling the vertically incoming photons into a laterally propagating mode while maintaining a small jitter and a thin Si device layer. In this work, we provide a 3D-based optical and electrical model based on practical fabrication conditions and discuss about design parameters, which include surface texturing, photon injection position, device area, and other features.

Young Children's Ability to Match Facial Features Typical of Race.

ERIC Educational Resources Information Center

Lacoste, Ronald J.

This study examined (1) the ability of 3- and 4-year-old children to racially classify Negro and Caucasian facial features in the absence of skin color as a racial cue; and (2) the relative value attached to the facial features of Negro and Caucasian races. Subjects were 21 middle income, Caucasian children from a privately owned nursery school in…

Wilderness Medicine Newsletter, Volume 9.

ERIC Educational Resources Information Center

Weber, Holly A., Ed.

1998-01-01

This document consists of the six issues of the "Wilderness Medicine Newsletter" published during 1998. The newsletter provides medical and rescue information for the non-physician in remote wilderness areas. Issues typically include feature articles, conference and training courses schedules, and personal narratives. Feature articles in…

Wideband monolithically integrated front-end subsystems and components

NASA Astrophysics Data System (ADS)

Mruk, Joseph Rene

This thesis presents the analysis, design, and measurements of passive, monolithically integrated, wideband recta-coax and printed circuit board front-end components. Monolithic fabrication of antennas, impedance transformers, filters, and transitions lowers manufacturing costs by reducing assembly time and enhances performance by removing connectors and cabling between the devices. Computational design, fabrication, and measurements are used to demonstrate the capabilities of these front-end assemblies. Two-arm wideband planar log-periodic antennas fed using a horizontal feed that allows for filters and impedance transformers to be readily fabricated within the radiating region of the antenna are demonstrated. At microwave frequencies, low-cost printed circuit board processes are typically used to produce planar devices. A 1.8 to 11 GHz two-arm planar log-periodic antenna is designed with a monolithically integrated impedance transformer. Band rejection methods based on modifying the antenna aperture, use of an integrated filter, and the application of both methods are investigated with realized gain suppressions of over 25 dB achieved. The ability of standard circuit board technology to fabricate millimeter-wave devices up to 110 GHz is severely limited. Thin dielectrics are required to prevent the excitation of higher order modes in the microstrip substrate. Fabricating the thin line widths required for the antenna aperture also becomes prohibitively challenging. Surface micro-machining typically used in the fabrication of MEMS devices is capable of producing the extremely small features that can be used to fabricate antennas extending through W-band. A directly RF fed 18 to 110 GHz planar log-periodic antenna is developed. The antenna is fabricated with an integrated impedance transformer and additional transitions for measurement characterization. Singly terminated low-loss wideband millimeter-wave filters operating over V- and W- band are developed. High quality performance of an 18 to 100 GHz front-end is realized by dividing the single instantaneous antenna into two apertures operating from 18 to 50 and 50 to 100 GHz. Each channel features an impedance transformer, low-pass (low-frequency) or band-pass (high-frequency) filter, and grounded CPW launch. This dual-aperture front-end demonstrates that micromachining technology is now capable of fabricating broadband millimeter-wave components with a high degree of integration.

Integrated topology for an aircraft electric power distribution system using MATLAB and ILP optimization technique and its implementation

NASA Astrophysics Data System (ADS)

Madhikar, Pratik Ravindra

The most important and crucial design feature while designing an Aircraft Electric Power Distribution System (EPDS) is reliability. In EPDS, the distribution of power is from top level generators to bottom level loads through various sensors, actuators and rectifiers with the help of AC & DC buses and control switches. As the demands of the consumer is never ending and the safety is utmost important, there is an increase in loads and as a result increase in power management. Therefore, the design of an EPDS should be optimized to have maximum efficiency. This thesis discusses an integrated tool that is based on a Need Based Design method and Fault Tree Analysis (FTA) to achieve the optimum design of an EPDS to provide maximum reliability in terms of continuous connectivity, power management and minimum cost. If an EPDS is formulated as an optimization problem then it can be solved with the help of connectivity, cost and power constraints by using a linear solver to get the desired output of maximum reliability at minimum cost. Furthermore, the thesis also discusses the viability and implementation of the resulted topology on typical large aircraft specifications.

Development of a Support Vector Machine - Based Image Analysis System for Focal Liver Lesions Classification in Magnetic Resonance Images

NASA Astrophysics Data System (ADS)

Gatos, I.; Tsantis, S.; Karamesini, M.; Skouroliakou, A.; Kagadis, G.

2015-09-01

Purpose: The design and implementation of a computer-based image analysis system employing the support vector machine (SVM) classifier system for the classification of Focal Liver Lesions (FLLs) on routine non-enhanced, T2-weighted Magnetic Resonance (MR) images. Materials and Methods: The study comprised 92 patients; each one of them has undergone MRI performed on a Magnetom Concerto (Siemens). Typical signs on dynamic contrast-enhanced MRI and biopsies were employed towards a three class categorization of the 92 cases: 40-benign FLLs, 25-Hepatocellular Carcinomas (HCC) within Cirrhotic liver parenchyma and 27-liver metastases from Non-Cirrhotic liver. Prior to FLLs classification an automated lesion segmentation algorithm based on Marcov Random Fields was employed in order to acquire each FLL Region of Interest. 42 texture features derived from the gray-level histogram, co-occurrence and run-length matrices and 12 morphological features were obtained from each lesion. Stepwise multi-linear regression analysis was utilized to avoid feature redundancy leading to a feature subset that fed the multiclass SVM classifier designed for lesion classification. SVM System evaluation was performed by means of leave-one-out method and ROC analysis. Results: Maximum accuracy for all three classes (90.0%) was obtained by means of the Radial Basis Kernel Function and three textural features (Inverse- Different-Moment, Sum-Variance and Long-Run-Emphasis) that describe lesion's contrast, variability and shape complexity. Sensitivity values for the three classes were 92.5%, 81.5% and 96.2% respectively, whereas specificity values were 94.2%, 95.3% and 95.5%. The AUC value achieved for the selected subset was 0.89 with 0.81 - 0.94 confidence interval. Conclusion: The proposed SVM system exhibit promising results that could be utilized as a second opinion tool to the radiologist in order to decrease the time/cost of diagnosis and the need for patients to undergo invasive examination.

Asymmetrical access to color and location in visual working memory.

PubMed

Rajsic, Jason; Wilson, Daryl E

2014-10-01

Models of visual working memory (VWM) have benefitted greatly from the use of the delayed-matching paradigm. However, in this task, the ability to recall a probed feature is confounded with the ability to maintain the proper binding between the feature that is to be reported and the feature (typically location) that is used to cue a particular item for report. Given that location is typically used as a cue-feature, we used the delayed-estimation paradigm to compare memory for location to memory for color, rotating which feature was used as a cue and which was reported. Our results revealed several novel findings: 1) the likelihood of reporting a probed object's feature was superior when reporting location with a color cue than when reporting color with a location cue; 2) location report errors were composed entirely of swap errors, with little to no random location reports; and 3) both colour and location reports greatly benefitted from the presence of nonprobed items at test. This last finding suggests that it is uncertainty over the bindings between locations and colors at memory retrieval that drive swap errors, not at encoding. We interpret our findings as consistent with a representational architecture that nests remembered object features within remembered locations.

Use of the Zebrafish Larvae as a Model to Study Cigarette Smoke Condensate Toxicity

PubMed Central

Ellis, Lee D.; Soo, Evelyn C.; Achenbach, John C.; Morash, Michael G.; Soanes, Kelly H.

2014-01-01

The smoking of tobacco continues to be the leading cause of premature death worldwide and is linked to the development of a number of serious illnesses including heart disease, respiratory diseases, stroke and cancer. Currently, cell line based toxicity assays are typically used to gain information on the general toxicity of cigarettes and other tobacco products. However, they provide little information regarding the complex disease-related changes that have been linked to smoking. The ethical concerns and high cost associated with mammalian studies have limited their widespread use for in vivo toxicological studies of tobacco. The zebrafish has emerged as a low-cost, high-throughput, in vivo model in the study of toxicology. In this study, smoke condensates from 2 reference cigarettes and 6 Canadian brands of cigarettes with different design features were assessed for acute, developmental, cardiac, and behavioural toxicity (neurotoxicity) in zebrafish larvae. By making use of this multifaceted approach we have developed an in vivo model with which to compare the toxicity profiles of smoke condensates from cigarettes with different design features. This model system may provide insights into the development of smoking related disease and could provide a cost-effective, high-throughput platform for the future evaluation of tobacco products. PMID:25526262

Design, synthesis and biological evaluation of N-methyl-N-[(1,2,3-triazol-4-yl)alkyl]propargylamines as novel monoamine oxidase B inhibitors.

PubMed

Di Pietro, Ornella; Alencar, Nelson; Esteban, Gerard; Viayna, Elisabet; Szałaj, Natalia; Vázquez, Javier; Juárez-Jiménez, Jordi; Sola, Irene; Pérez, Belén; Solé, Montse; Unzeta, Mercedes; Muñoz-Torrero, Diego; Luque, F Javier

2016-10-15

Different azides and alkynes have been coupled via Cu-catalyzed 1,3-dipolar Huisgen cycloaddition to afford a novel family of N 1 - and C 5 -substituted 1,2,3-triazole derivatives that feature the propargylamine group typical of irreversible MAO-B inhibitors at the C4-side chain of the triazole ring. All the synthesized compounds were evaluated against human MAO-A and MAO-B. Structure-activity relationships and molecular modeling were utilized to gain insight into the structural and chemical features that enhance the binding affinity and selectivity between the two enzyme isoforms. Several lead compounds, in terms of potency (submicromolar to low micromolar range), MAO-B selective recognition, and brain permeability, were identified. One of these leads (MAO-B IC 50 of 3.54μM, selectivity MAO-A/MAO-B index of 27.7) was further subjected to reversibility and time-dependence inhibition studies, which disclosed a slow and irreversible inhibition of human MAO-B. Overall, the results support the suitability of the 4-triazolylalkyl propargylamine scaffold for exploring the design of multipotent anti-Alzheimer compounds endowed with irreversible MAO-B inhibitory activity. Copyright © 2016 Elsevier Ltd. All rights reserved.

Use of the zebrafish larvae as a model to study cigarette smoke condensate toxicity.

PubMed

Ellis, Lee D; Soo, Evelyn C; Achenbach, John C; Morash, Michael G; Soanes, Kelly H

2014-01-01

The smoking of tobacco continues to be the leading cause of premature death worldwide and is linked to the development of a number of serious illnesses including heart disease, respiratory diseases, stroke and cancer. Currently, cell line based toxicity assays are typically used to gain information on the general toxicity of cigarettes and other tobacco products. However, they provide little information regarding the complex disease-related changes that have been linked to smoking. The ethical concerns and high cost associated with mammalian studies have limited their widespread use for in vivo toxicological studies of tobacco. The zebrafish has emerged as a low-cost, high-throughput, in vivo model in the study of toxicology. In this study, smoke condensates from 2 reference cigarettes and 6 Canadian brands of cigarettes with different design features were assessed for acute, developmental, cardiac, and behavioural toxicity (neurotoxicity) in zebrafish larvae. By making use of this multifaceted approach we have developed an in vivo model with which to compare the toxicity profiles of smoke condensates from cigarettes with different design features. This model system may provide insights into the development of smoking related disease and could provide a cost-effective, high-throughput platform for the future evaluation of tobacco products.

Use of statecharts in the modelling of dynamic behaviour in the ATLAS DAQ prototype-1

NASA Astrophysics Data System (ADS)

Croll, P.; Duval, P.-Y.; Jones, R.; Kolos, S.; Sari, R. F.; Wheeler, S.

1998-08-01

Many applications within the ATLAS DAQ prototype-1 system have complicated dynamic behaviour which can be successfully modelled in terms of states and transitions between states. Previously, state diagrams implemented as finite-state machines have been used. Although effective, they become ungainly as system size increases. Harel statecharts address this problem by implementing additional features such as hierarchy and concurrency. The CHSM object-oriented language system is freeware which implements Harel statecharts as concurrent, hierarchical, finite-state machines (CHSMs). An evaluation of this language system by the ATLAS DAQ group has shown it to be suitable for describing the dynamic behaviour of typical DAQ applications. The language is currently being used to model the dynamic behaviour of the prototype-1 run-control system. The design is specified by means of a CHSM description file, and C++ code is obtained by running the CHSM compiler on the file. In parallel with the modelling work, a code generator has been developed which translates statecharts, drawn using the StP CASE tool, into the CHSM language. C++ code, describing the dynamic behaviour of the run-control system, has been successfully generated directly from StP statecharts using the CHSM generator and compiler. The validity of the design was tested using the simulation features of the Statemate CASE tool.

Shape-optimization of round-to-slot holes for improving film cooling effectiveness on a flat surface

NASA Astrophysics Data System (ADS)

Huang, Ying; Zhang, Jing-zhou; Wang, Chun-hua

2018-01-01

Single-objective optimization for improving adiabatic film cooling effectiveness is performed for single row of round-to-slot film cooling holes on a flat surface by using CFD analysis and surrogate approximation methods. Among the main geometric parameters, dimensionless hole-to-hole pitch (P/d) and slot length-to-diameter (l/d) are fixed as 2.4 and 2 respectively, and the other parameters (hole height-to-diameter ratio, slot width-to-diameter and inclination angle) are chosen as the design variables. Given a wide range of possible geometric variables, the geometric optimization of round-to-slot holes is carried out under two typical blowing ratios of M = 0.5 and M = 1.5 by selecting a spatially-averaged adiabatic film cooling effectiveness between x/d = 2 and x/d = 12 as the objective function to be maximized. Radial basis function neural network is applied for constructing the surrogate model and then the optimal design point is searched by a genetic algorithm. It is revealed that the optimal round-to-slot hole is of converging feature under a low blowing ratio but of diffusing feature under a high blowing ratio. Further, the influence principle of optimal round-to-slot geometry on film cooling performance is illustrated according to the detailed flow and thermal behaviors.

Shape-optimization of round-to-slot holes for improving film cooling effectiveness on a flat surface

NASA Astrophysics Data System (ADS)

Huang, Ying; Zhang, Jing-zhou; Wang, Chun-hua

2018-06-01

Single-objective optimization for improving adiabatic film cooling effectiveness is performed for single row of round-to-slot film cooling holes on a flat surface by using CFD analysis and surrogate approximation methods. Among the main geometric parameters, dimensionless hole-to-hole pitch ( P/ d) and slot length-to-diameter ( l/ d) are fixed as 2.4 and 2 respectively, and the other parameters (hole height-to-diameter ratio, slot width-to-diameter and inclination angle) are chosen as the design variables. Given a wide range of possible geometric variables, the geometric optimization of round-to-slot holes is carried out under two typical blowing ratios of M = 0.5 and M = 1.5 by selecting a spatially-averaged adiabatic film cooling effectiveness between x/ d = 2 and x/ d = 12 as the objective function to be maximized. Radial basis function neural network is applied for constructing the surrogate model and then the optimal design point is searched by a genetic algorithm. It is revealed that the optimal round-to-slot hole is of converging feature under a low blowing ratio but of diffusing feature under a high blowing ratio. Further, the influence principle of optimal round-to-slot geometry on film cooling performance is illustrated according to the detailed flow and thermal behaviors.

Supporting 64-bit global indices in Epetra and other Trilinos packages :

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jhurani, Chetan; Austin, Travis M.; Heroux, Michael Allen

The Trilinos Project is an effort to facilitate the design, development, integration and ongoing support of mathematical software libraries within an object-oriented framework. It is intended for large-scale, complex multiphysics engineering and scientific applications [2, 4, 3]. Epetra is one of its basic packages. It provides serial and parallel linear algebra capabilities. Before Trilinos version 11.0, released in 2012, Epetra used the C++ int data-type for storing global and local indices for degrees of freedom (DOFs). Since int is typically 32-bit, this limited the largest problem size to be smaller than approximately two billion DOFs. This was true even ifmore » a distributed memory machine could handle larger problems. We have added optional support for C++ long long data-type, which is at least 64-bit wide, for global indices. To save memory, maintain the speed of memory-bound operations, and reduce further changes to the code, the local indices are still 32-bit. We document the changes required to achieve this feature and how the new functionality can be used. We also report on the lessons learned in modifying a mature and popular package from various perspectives design goals, backward compatibility, engineering decisions, C++ language features, effects on existing users and other packages, and build integration.« less

Design of a radio telescope surface segment actuator based on a form-closed eccentric cam

NASA Astrophysics Data System (ADS)

Smith, David R.

2014-07-01

As radio telescopes have reached larger diameters and higher frequencies, it is typically not possible to meet their surface accuracy specifications using passive homology-based designs. The most common solution to this problem in the current generation of large, high-frequency radio telescopes is to employ a system of linear actuators to correct the surface shape of the primary reflector. The exact specifications of active surface actuators vary with the telescope. However, they have many common features, some of which drive their design. In general, these actuators must provide precise and repeatable positioning under significant loads during operation and they must withstand even higher loads for survival conditions. For general safety, they typically must hold position in the event of a power failure and must incorporate position limits, whether electrical, mechanical, or both. Because the number of actuators is generally high for large active surfaces (hundreds or even thousands of actuators), they must also be reliable and of reasonable individual cost. Finally, for maximum flexibility in their installation, they must be compact. This paper presents a concept for an active surface actuator based on a form-closed eccentric cam (kinematically, a Scotch Yoke mechanism). Such a design is limited in stroke, but offers potential advantages in terms of manufacture, compactness, measurement, and survival loading. The paper demonstrates that some of the expected advantages cannot be practically realized, due to dimensions that are driven by survival loading conditions. As a result, this concept is likely to offer an advantage over conventional screw-type actuators only for cases where actuator runaway and stall are the driving considerations.

Application of a neural network for reflectance spectrum classification

NASA Astrophysics Data System (ADS)

Yang, Gefei; Gartley, Michael

2017-05-01

Traditional reflectance spectrum classification algorithms are based on comparing spectrum across the electromagnetic spectrum anywhere from the ultra-violet to the thermal infrared regions. These methods analyze reflectance on a pixel by pixel basis. Inspired by high performance that Convolution Neural Networks (CNN) have demonstrated in image classification, we applied a neural network to analyze directional reflectance pattern images. By using the bidirectional reflectance distribution function (BRDF) data, we can reformulate the 4-dimensional into 2 dimensions, namely incident direction × reflected direction × channels. Meanwhile, RIT's micro-DIRSIG model is utilized to simulate additional training samples for improving the robustness of the neural networks training. Unlike traditional classification by using hand-designed feature extraction with a trainable classifier, neural networks create several layers to learn a feature hierarchy from pixels to classifier and all layers are trained jointly. Hence, the our approach of utilizing the angular features are different to traditional methods utilizing spatial features. Although training processing typically has a large computational cost, simple classifiers work well when subsequently using neural network generated features. Currently, most popular neural networks such as VGG, GoogLeNet and AlexNet are trained based on RGB spatial image data. Our approach aims to build a directional reflectance spectrum based neural network to help us to understand from another perspective. At the end of this paper, we compare the difference among several classifiers and analyze the trade-off among neural networks parameters.

Unilateral nasal pain with migraine features.

PubMed

Alvarez, Mónica; Montojo, Teresa; de la Casa, Beatriz; Vela, Lydia; Pareja, Juan A

2013-09-01

Migraine attacks exclusively felt in the face are very rare, the pain involving the territories supplied by the second and third branches of the trigeminal nerve. Two patients suffering from heminasal pain attacks accompanied with typical migrainous features and responsive to oral or intranasal triptans - but not to intranasal lidocaine or oxymetazoline. In one patient, the attacks could be precipitated upon slight touching on the tip of the nose, in the other attacks were preceded by the nasal sensation typically heralding sneezing. Migraine pain mostly develops within the innervation territory of the first branch of the trigeminal nerve, which includes the nose. Therefore, episodes of unilateral nasal pain with migrainous features could be considered a migraine with unusual topography (nasal migraine). Painful nasal attacks occasionally preceded by stimulation of trigeminal afferents in the nose, could be conceived of as migraine-tic syndrome.

Reliability in content analysis: The case of semantic feature norms classification.

PubMed

Bolognesi, Marianna; Pilgram, Roosmaryn; van den Heerik, Romy

2017-12-01

Semantic feature norms (e.g., STIMULUS: car → RESPONSE: ) are commonly used in cognitive psychology to look into salient aspects of given concepts. Semantic features are typically collected in experimental settings and then manually annotated by the researchers into feature types (e.g., perceptual features, taxonomic features, etc.) by means of content analyses-that is, by using taxonomies of feature types and having independent coders perform the annotation task. However, the ways in which such content analyses are typically performed and reported are not consistent across the literature. This constitutes a serious methodological problem that might undermine the theoretical claims based on such annotations. In this study, we first offer a review of some of the released datasets of annotated semantic feature norms and the related taxonomies used for content analysis. We then provide theoretical and methodological insights in relation to the content analysis methodology. Finally, we apply content analysis to a new dataset of semantic features and show how the method should be applied in order to deliver reliable annotations and replicable coding schemes. We tackle the following issues: (1) taxonomy structure, (2) the description of categories, (3) coder training, and (4) sustainability of the coding scheme-that is, comparison of the annotations provided by trained versus novice coders. The outcomes of the project are threefold: We provide methodological guidelines for semantic feature classification; we provide a revised and adapted taxonomy that can (arguably) be applied to both concrete and abstract concepts; and we provide a dataset of annotated semantic feature norms.

How Necessary Are the Stripes of a Tiger? Diagnostic and Characteristic Features in an fMRI Study of Word Meaning

ERIC Educational Resources Information Center

Grossman, Murray; Troiani, Vanessa; Koenig, Phyllis; Work, Melissa; Moore, Peachie

2007-01-01

This study contrasted two approaches to word meaning: the statistically determined role of high-contribution features like "striped" in the meaning of complex nouns like "tiger" typically used in studies of semantic memory, and the contribution of diagnostic features like "parent's brother" that play a critical role in the meaning of nominal kinds…

Intelligent error correction method applied on an active pixel sensor based star tracker

NASA Astrophysics Data System (ADS)

Schmidt, Uwe

2005-10-01

Star trackers are opto-electronic sensors used on-board of satellites for the autonomous inertial attitude determination. During the last years star trackers became more and more important in the field of the attitude and orbit control system (AOCS) sensors. High performance star trackers are based up today on charge coupled device (CCD) optical camera heads. The active pixel sensor (APS) technology, introduced in the early 90-ties, allows now the beneficial replacement of CCD detectors by APS detectors with respect to performance, reliability, power, mass and cost. The company's heritage in star tracker design started in the early 80-ties with the launch of the worldwide first fully autonomous star tracker system ASTRO1 to the Russian MIR space station. Jena-Optronik recently developed an active pixel sensor based autonomous star tracker "ASTRO APS" as successor of the CCD based star tracker product series ASTRO1, ASTRO5, ASTRO10 and ASTRO15. Key features of the APS detector technology are, a true xy-address random access, the multiple windowing read out and the on-chip signal processing including the analogue to digital conversion. These features can be used for robust star tracking at high slew rates and under worse conditions like stray light and solar flare induced single event upsets. A special algorithm have been developed to manage the typical APS detector error contributors like fixed pattern noise (FPN), dark signal non-uniformity (DSNU) and white spots. The algorithm works fully autonomous and adapts to e.g. increasing DSNU and up-coming white spots automatically without ground maintenance or re-calibration. In contrast to conventional correction methods the described algorithm does not need calibration data memory like full image sized calibration data sets. The application of the presented algorithm managing the typical APS detector error contributors is a key element for the design of star trackers for long term satellite applications like geostationary telecom platforms.

High-performance camera module for fast quality inspection in industrial printing applications

NASA Astrophysics Data System (ADS)

Fürtler, Johannes; Bodenstorfer, Ernst; Mayer, Konrad J.; Brodersen, Jörg; Heiss, Dorothea; Penz, Harald; Eckel, Christian; Gravogl, Klaus; Nachtnebel, Herbert

2007-02-01

Today, printing products which must meet highest quality standards, e.g., banknotes, stamps, or vouchers, are automatically checked by optical inspection systems. Typically, the examination of fine details of the print or security features demands images taken from various perspectives, with different spectral sensitivity (visible, infrared, ultraviolet), and with high resolution. Consequently, the inspection system is equipped with several cameras and has to cope with an enormous data rate to be processed in real-time. Hence, it is desirable to move image processing tasks into the camera to reduce the amount of data which has to be transferred to the (central) image processing system. The idea is to transfer relevant information only, i.e., features of the image instead of the raw image data from the sensor. These features are then further processed. In this paper a color line-scan camera for line rates up to 100 kHz is presented. The camera is based on a commercial CMOS (complementary metal oxide semiconductor) area image sensor and a field programmable gate array (FPGA). It implements extraction of image features which are well suited to detect print flaws like blotches of ink, color smears, splashes, spots and scratches. The camera design and several image processing methods implemented on the FPGA are described, including flat field correction, compensation of geometric distortions, color transformation, as well as decimation and neighborhood operations.

a New Paradigm for Matching - and Aerial Images

NASA Astrophysics Data System (ADS)

Koch, T.; Zhuo, X.; Reinartz, P.; Fraundorfer, F.

2016-06-01

This paper investigates the performance of SIFT-based image matching regarding large differences in image scaling and rotation, as this is usually the case when trying to match images captured from UAVs and airplanes. This task represents an essential step for image registration and 3d-reconstruction applications. Various real world examples presented in this paper show that SIFT, as well as A-SIFT perform poorly or even fail in this matching scenario. Even if the scale difference in the images is known and eliminated beforehand, the matching performance suffers from too few feature point detections, ambiguous feature point orientations and rejection of many correct matches when applying the ratio-test afterwards. Therefore, a new feature matching method is provided that overcomes these problems and offers thousands of matches by a novel feature point detection strategy, applying a one-to-many matching scheme and substitute the ratio-test by adding geometric constraints to achieve geometric correct matches at repetitive image regions. This method is designed for matching almost nadir-directed images with low scene depth, as this is typical in UAV and aerial image matching scenarios. We tested the proposed method on different real world image pairs. While standard SIFT failed for most of the datasets, plenty of geometrical correct matches could be found using our approach. Comparing the estimated fundamental matrices and homographies with ground-truth solutions, mean errors of few pixels can be achieved.

Broadband Achromatic Telecentric Lens

NASA Technical Reports Server (NTRS)

Mouroulis, Pantazis

2007-01-01

A new type of lens design features broadband achromatic performance as well as telecentricity, using a minimum number of spherical elements. With appropriate modifications, the lens design form can be tailored to cover the range of response of the focal-plane array, from Si (400-1,000 nm) to InGaAs (400-1,700 or 2,100 nm) or InSb/HgCdTe reaching to 2,500 nm. For reference, lenses typically are achromatized over the visible wavelength range of 480-650 nm. In remote sensing applications, there is a need for broadband achromatic telescopes, normally satisfied with mirror-based systems. However, mirror systems are not always feasible due to size or geometry restrictions. They also require expensive aspheric surfaces. Non-obscured mirror systems can be difficult to align and have a limited (essentially one-dimensional) field of view. Centrally obscured types have a two-dimensional but very limited field in addition to the obscuration. Telecentricity is a highly desirable property for matching typical spectrometer types, as well as for reducing the variation of the angle of incidence and cross-talk on the detector for simple camera types. This rotationally symmetric telescope with no obscuration and using spherical surfaces and selected glass types fills a need in the range of short focal lengths. It can be used as a compact front unit for a matched spectrometer, as an ultra-broadband camera objective lens, or as the optics of an integrated camera/spectrometer in which the wavelength information is obtained by the use of strip or linear variable filters on the focal plane array. This kind of camera and spectrometer system can find applications in remote sensing, as well as in-situ applications for geological mapping and characterization of minerals, ecological studies, and target detection and identification through spectral signatures. Commercially, the lens can be used in quality-control applications via spectral analysis. The lens design is based on the rear landscape lens with the aperture stop in front of all elements. This allows sufficient room for telecentricity in addition to making the stop easily accessible. The crucial design features are the use of a doublet with an ultra-low dispersion glass (fluorite or S-FPL53), and the use of a strong negative element, which enables flat field and telecentricity in conjunction with the last (field lens) element. The field lens also can be designed to be in contact with the array, a feature that is desirable in some applications. The lens has a 20deg field of view, for a 50-mm focal length, and is corrected over the range of wavelengths of 450-2,300 nm. Transverse color, which is the most pernicious aberration for spectroscopic work, is controlled at the level of 1 m or below at 0.7 m field and 5 m at full field. The maximum chief ray angle is less than 1.7 , providing good telecentricity. An additional feature of this lens is that it is made exclusively with glasses that provide good transmission up to 2,300 nm and even some transmission to 2,500 nm; thus, the lens can be used in applications that cover the entire solar-reflected spectrum. Alternative realizations are possible that provide enhanced resolution and even less transverse color over a narrower wavelength range.

Case Assignment in Typically Developing English-Speaking Children: A Paired Priming Study

ERIC Educational Resources Information Center

Wisman Weil, Lisa Marie

2013-01-01

This study utilized a paired priming paradigm to examine the influence of input features on case assignment in typically developing English-speaking children. The Input Ambiguity Hypothesis (Pelham, 2011) was experimentally tested to help explain why children produce subject pronoun case errors. Analyses of third singular "-s" marking on…

Sleep Problems in Children with Autism and in Typically Developing Children

ERIC Educational Resources Information Center

Hoffman, Charles D.; Sweeney, Dwight P.; Gilliam, James E.; Lopez-Wagner, Muriel C.

2006-01-01

Although sleep problems are often seen as a clinical feature associated with autism, and children with autism are reported to have more sleep disturbances than typically developing children, there is a paucity of studies in the area and findings are restricted by problematic methodological approaches. The present study addressed these limitations,…

Adiposis dolorosa (Dercum's disease): MRI and ultrasound appearances.

PubMed

Tins, B J; Matthews, C; Haddaway, M; Cassar-Pullicino, V N; Lalam, R; Singh, J; Tyrrell, P N M

2013-10-01

To describe ultrasound and magnetic resonance imaging (MRI) features of adiposis dolorosa, Dercum's disease, and to evaluate the MRI features prospectively against a large number of MRI examinations. Institutional review board approval for this study was obtained. The imaging features at MRI and ultrasound of 13 cases of adiposis dolorosa (nine female, four male; age range 32-72 years) were reviewed. MRI findings typical for adiposis dolorosa were proposed and prospectively evaluated on 6247 MRI examinations performed over a period of 8 months. Adiposis dolorosa demonstrates multiple, oblong, fatty lesions in the superficial subcutaneous fatty tissue. They are mostly <2 cm in long axis diameter. They demonstrate nodular ("blush-like") increased fluid signal at unenhanced MRI and are markedly hyperechoic at ultrasound. There is no contrast medium enhancement at MRI and no increased Doppler signal at ultrasound. Most lesions were clinically asymptomatic, some were painful/tender. There was no imaging evidence of oedema or inflammation. During prospective validation of these MRI features on 6247 MRI examinations, two cases with typical imaging features were encountered; both were diagnosed as adiposis dolorosa on clinical review. All cases of adiposis dolorosa showed these imaging findings. This results in a very low likelihood that a nodular, blush-like appearance of subcutaneous fat on MRI is not due to adiposis dolorosa. Adiposis dolorosa, Dercum's disease, should be suggested in the presence of multiple (many) small, oblong, fatty lesions in the subcutaneous fatty tissue in adult patients if they are hyperechoic on ultrasound imaging or blush-like at unenhanced MRI; typically a small number of these lesions are tender/painful. Imaging does not demonstrate inflammation or oedema in relation to these lesions. These MRI features should suggest the diagnosis and are likely to be pathognomonic. The radiologist is often the first to suggest the diagnosis based on the imaging features. Copyright © 2013 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

Epithelioid hemangioma of the spine: Two cases.

PubMed

O'Shea, Bendan M; Kim, Jinsuh

2014-01-01

We report two cases of epithelioid hemangioma (EH) manifested in the thoracic spine with associated clinical, radiographic, and pathological findings. Epithelioid hemangioma is a benign vascular tumor that can involve any bone (including the spine in a subset of patients). Although recognized as a benign tumor by the WHO, it can display locally aggressive features. Within the spine, these features may lead to pain, instability, and/or neurologic dysfunction. The radiographic appearance is most typically that of a lytic, well-defined lesion on plain film or CT. The MRI appearance is typically hypointense on T1WI, hyperintense on T2WI, and avidly enhancing, often with an extraosseous soft-tissue component.

[Hypersomnia: a diagnostic problem].

PubMed

Kranenburg, Guido; Teunissen, Laurien L

2014-01-01

Hypersomnia is a frequently occurring problem. When taking a medical history it is important to distinguish between fatigue and sleepiness. We present a 14-year-old girl with narcolepsy and a 59-year-old man with idiopathic hypersomnia. Features that are typical of narcolepsy are cataplexy and weight gain. Features that are typical of both narcolepsy and idiopathic hypersomnia are daytime naps, insomnia, sleep paralysis and hypnagogic hallucinations. Additional testing in patients with hypersomnia should include a polysomnography in order to exclude other sleeping disorders, and a mean sleep latency test. Practice shows that both patients with narcolepsy and those with idiopathic hypersomnia benefit from treatment with stimulating drugs such as modafinil.

A model of face selection in viewing video stories.

PubMed

Suda, Yuki; Kitazawa, Shigeru

2015-01-19

When typical adults watch TV programs, they show surprisingly stereo-typed gaze behaviours, as indicated by the almost simultaneous shifts of their gazes from one face to another. However, a standard saliency model based on low-level physical features alone failed to explain such typical gaze behaviours. To find rules that explain the typical gaze behaviours, we examined temporo-spatial gaze patterns in adults while they viewed video clips with human characters that were played with or without sound, and in the forward or reverse direction. We here show the following: 1) the "peak" face scanpath, which followed the face that attracted the largest number of views but ignored other objects in the scene, still retained the key features of actual scanpaths, 2) gaze behaviours remained unchanged whether the sound was provided or not, 3) the gaze behaviours were sensitive to time reversal, and 4) nearly 60% of the variance of gaze behaviours was explained by the face saliency that was defined as a function of its size, novelty, head movements, and mouth movements. These results suggest that humans share a face-oriented network that integrates several visual features of multiple faces, and directs our eyes to the most salient face at each moment.

Recent Observations and Modeling of Narrowband Stimulated Electromagnetic Emissions SEEs at the HAARP Facility

NASA Astrophysics Data System (ADS)

Scales, Wayne; Bernhardt, Paul; McCarrick, Michael; Briczinski, Stanley; Mahmoudian, Alireza; Fu, Haiyang; Ranade Bordikar, Maitrayee; Samimi, Alireza

There has been significant interest in so-called narrowband Stimulated Electromagnetic Emission SEE over the past several years due to recent discoveries at the High Frequency Active Auroral Research Program HAARP facility near Gakone, Alaska. Narrowband SEE (NSEE) has been defined as spectral features in the SEE spectrum typically within 1 kHz of the transmitter (or pump) frequency. SEE is due to nonlinear processes leading to re-radiation at frequencies other than the pump wave frequency during heating the ionospheric plasma with high power HF radio waves. Although NSEE exhibits a richly complex structure, it has now been shown after a substantial number of observations at HAARP, that NSEE can be grouped into two basic classes. The first are those spectral features, associated with Stimulated Brillouin Scatter SBS, which typically occur when the pump frequency is not close to electron gyro-harmonic frequencies. Typically, these spectral features are within roughly 50 Hz of the pump wave frequency where it is to be noted that the O+ ion gyro-frequency is roughly 50 Hz. The second class of spectral features corresponds to the case when the pump wave frequency is typically within roughly 10 kHz of electron gyro-harmonic frequencies. In this case, spectral features ordered by harmonics of ion gyro-frequencies are typically observed, and termed Stimulated Ion Bernstein Scatter SIBS. There is also important parametric behavior on both classes of NSEE depending on the pump wave parameters including the field strength, antenna beam angle, and electron gyro-harmonic number. This presentation will first provide an overview of the recent NSEE experimental observations at HAARP. Both Stimulated Brillouin Scatter SBS and Stimulated Ion Bernstein Scatter SIBS observations will be discussed as well as their relationship to each other. Possible theoretical formulation in terms of parametric decay instabilities will be provided. Computer simulation model results will be presented to provide insight into associated higher order nonlinear effects including particle acceleration and wave-wave processes. Both theory and model results will be put into the context of the experimental observations. Finally, possible applications of NSEE will be pointed out including triggering diagnostics for artificial ionization layer formation, proton precipitation event diagnostics, and electron temperature measurements in the heated volume.

Another lesson from plants: the forward osmosis-based actuator.

PubMed

Sinibaldi, Edoardo; Argiolas, Alfredo; Puleo, Gian Luigi; Mazzolai, Barbara

2014-01-01

Osmotic actuation is a ubiquitous plant-inspired actuation strategy that has a very low power consumption but is capable of generating effective movements in a wide variety of environmental conditions. In light of these features, we aimed to develop a novel, low-power-consumption actuator that is capable of generating suitable forces during a characteristic actuation time on the order of a few minutes. Based on the analysis of plant movements and on osmotic actuation modeling, we designed and fabricated a forward osmosis-based actuator with a typical size of 10 mm and a characteristic time of 2-5 minutes. To the best of our knowledge, this is the fastest osmotic actuator developed so far. Moreover, the achieved timescale can be compared to that of a typical plant cell, thanks to the integrated strategy that we pursued by concurrently addressing and solving design and material issues, as paradigmatically explained by the bioinspired approach. Our osmotic actuator produces forces above 20 N, while containing the power consumption (on the order of 1 mW). Furthermore, based on the agreement between model predictions and experimental observations, we also discuss the actuator performance (including power consumption, maximum force, energy density and thermodynamic efficiency) in relation to existing actuation technologies. In light of the achievements of the present study, the proposed osmotic actuator holds potential for effective exploitation in bioinspired robotics systems.

Wind-Tunnel Results of Advanced High-Speed Propellers at Takeoff, Climb, and Landing Mach Numbers

NASA Technical Reports Server (NTRS)

Stefko, George L.; Jeracki, Robert J.

1985-01-01

Low-speed wind-tunnel performance tests of two advanced propellers have been completed at the NASA Lewis Research Center as part of the NASA Advanced Turboprop Program. The 62.2 cm (24.5 in.) diameter adjustable-pitch models were tested at Mach numbers typical of takeoff, initial climbout, and landing speeds (i.e., from Mach 0.10 to 0.34) at zero angle of attack in the NASA Lewis 10 by 10 Foot Supersonic Wind Tunnel. Both models had eight blades and a cruise-design-point operating condition of Mach 0.80, and 10.668 km (35,000 ft) I.S.A. altitude, a 243.8 m/s (800 ft/sec) tip speed, and a high power loading of 301 kW/sq m (37.5 shp/sq ft). Each model had its own integrally designed area-ruled spinner, but used the same specially contoured nacelle. These features reduced blade-section Mach numbers and relieved blade-root choking at the cruise condition. No adverse or unusual low-speed operating conditions were found during the test with either the straight blade SR-2 or the 45 deg swept SR-3 propeller. Typical efficiencies of the straight and 45 deg swept propellers were 50.2 and 54.9 percent, respectively, at a takeoff condition of Mach 0.20 and 53.7 and 59.1 percent, respectively, at a climb condition of Mach 0.34.

Another Lesson from Plants: The Forward Osmosis-Based Actuator

PubMed Central

Sinibaldi, Edoardo; Argiolas, Alfredo; Puleo, Gian Luigi; Mazzolai, Barbara

2014-01-01

Osmotic actuation is a ubiquitous plant-inspired actuation strategy that has a very low power consumption but is capable of generating effective movements in a wide variety of environmental conditions. In light of these features, we aimed to develop a novel, low-power-consumption actuator that is capable of generating suitable forces during a characteristic actuation time on the order of a few minutes. Based on the analysis of plant movements and on osmotic actuation modeling, we designed and fabricated a forward osmosis-based actuator with a typical size of 10 mm and a characteristic time of 2–5 minutes. To the best of our knowledge, this is the fastest osmotic actuator developed so far. Moreover, the achieved timescale can be compared to that of a typical plant cell, thanks to the integrated strategy that we pursued by concurrently addressing and solving design and material issues, as paradigmatically explained by the bioinspired approach. Our osmotic actuator produces forces above 20 N, while containing the power consumption (on the order of 1 mW). Furthermore, based on the agreement between model predictions and experimental observations, we also discuss the actuator performance (including power consumption, maximum force, energy density and thermodynamic efficiency) in relation to existing actuation technologies. In light of the achievements of the present study, the proposed osmotic actuator holds potential for effective exploitation in bioinspired robotics systems. PMID:25020043

The occurrence of hormetic dose responses in the toxicological literature, the hormesis database: an overview

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calabrese, Edward J.; Blain, Robyn

A relational retrieval database has been developed compiling toxicological studies assessing the occurrence of hormetic dose responses and their quantitative characteristics. This database permits an evaluation of these studies over numerous parameters, including study design and dose-response features and physical/chemical properties of the agents. The database contains approximately 5600 dose-response relationships satisfying evaluative criteria for hormesis across over approximately 900 agents from a broadly diversified spectrum of chemical classes and physical agents. The assessment reveals that hormetic dose-response relationships occur in males and females of numerous animal models in all principal age groups as well as across species displaying amore » broad range of differential susceptibilities to toxic agents. The biological models are extensive, including plants, viruses, bacteria, fungi, insects, fish, birds, rodents, and primates, including humans. The spectrum of endpoints displaying hormetic dose responses is also broad being inclusive of growth, longevity, numerous metabolic parameters, disease incidences (including cancer), various performance endpoints such as cognitive functions, immune responses among others. Quantitative features of the hormetic dose response reveal that the vast majority of cases display a maximum stimulatory response less than two-fold greater than the control while the width of the stimulatory response is typically less than 100-fold in dose range immediately contiguous with the toxicological NO(A)EL. The database also contains a quantitative evaluation component that differentiates among the various dose responses concerning the strength of the evidence supporting a hormetic conclusion based on study design features, magnitude of the stimulatory response, statistical significance, and reproducibility of findings.« less

Design of Content Based Image Retrieval Scheme for Diabetic Retinopathy Images using Harmony Search Algorithm.

PubMed

Sivakamasundari, J; Natarajan, V

2015-01-01

Diabetic Retinopathy (DR) is a disorder that affects the structure of retinal blood vessels due to long-standing diabetes mellitus. Automated segmentation of blood vessel is vital for periodic screening and timely diagnosis. An attempt has been made to generate continuous retinal vasculature for the design of Content Based Image Retrieval (CBIR) application. The typical normal and abnormal retinal images are preprocessed to improve the vessel contrast. The blood vessels are segmented using evolutionary based Harmony Search Algorithm (HSA) combined with Otsu Multilevel Thresholding (MLT) method by best objective functions. The segmentation results are validated with corresponding ground truth images using binary similarity measures. The statistical, textural and structural features are obtained from the segmented images of normal and DR affected retina and are analyzed. CBIR in medical image retrieval applications are used to assist physicians in clinical decision-support techniques and research fields. A CBIR system is developed using HSA based Otsu MLT segmentation technique and the features obtained from the segmented images. Similarity matching is carried out between the features of query and database images using Euclidean Distance measure. Similar images are ranked and retrieved. The retrieval performance of CBIR system is evaluated in terms of precision and recall. The CBIR systems developed using HSA based Otsu MLT and conventional Otsu MLT methods are compared. The retrieval performance such as precision and recall are found to be 96% and 58% for CBIR system using HSA based Otsu MLT segmentation. This automated CBIR system could be recommended for use in computer assisted diagnosis for diabetic retinopathy screening.

The occurrence of hormetic dose responses in the toxicological literature, the hormesis database: an overview.

PubMed

Calabrese, Edward J; Blain, Robyn

2005-02-01

A relational retrieval database has been developed compiling toxicological studies assessing the occurrence of hormetic dose responses and their quantitative characteristics. This database permits an evaluation of these studies over numerous parameters, including study design and dose-response features and physical/chemical properties of the agents. The database contains approximately 5600 dose-response relationships satisfying evaluative criteria for hormesis across over approximately 900 agents from a broadly diversified spectrum of chemical classes and physical agents. The assessment reveals that hormetic dose-response relationships occur in males and females of numerous animal models in all principal age groups as well as across species displaying a broad range of differential susceptibilities to toxic agents. The biological models are extensive, including plants, viruses, bacteria, fungi, insects, fish, birds, rodents, and primates, including humans. The spectrum of endpoints displaying hormetic dose responses is also broad being inclusive of growth, longevity, numerous metabolic parameters, disease incidences (including cancer), various performance endpoints such as cognitive functions, immune responses among others. Quantitative features of the hormetic dose response reveal that the vast majority of cases display a maximum stimulatory response less than two-fold greater than the control while the width of the stimulatory response is typically less than 100-fold in dose range immediately contiguous with the toxicological NO(A)EL. The database also contains a quantitative evaluation component that differentiates among the various dose responses concerning the strength of the evidence supporting a hormetic conclusion based on study design features, magnitude of the stimulatory response, statistical significance, and reproducibility of findings.

Building America Case Study: Ground Source Heat Pump Research, TaC Studios Residence, Atlanta, Georigia (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2014-09-01

As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA in the mixed-humid climate. This home serves as a residence and home office for the firm's owners, as well as a demonstration of their design approach to potential and current clients. Southface believes the home demonstrates current best practices for the mixed-humid climate, including a building envelope featuring advanced air sealing details and low density spray foam insulation, glazing that exceeds ENERGY STARmore » requirements, and a high performance heating and cooling system. Construction quality and execution was a high priority for TaC Studios and was ensured by a third party review process. Post construction testing showed that the project met stated goals for envelope performance, an air infiltration rate of 2.15 ACH50. The homeowner's wished to further validate whole house energy savings through the project's involvement with Building America and this long-term monitoring effort. As a Building America test home, this home was evaluated to detail whole house energy use, end use loads, and the efficiency and operation of the ground source heat pump and associated systems. Given that the home includes many non-typical end use loads including a home office, pool, landscape water feature, and other luxury features not accounted for in Building America modeling tools, these end uses were separately monitored to determine their impact on overall energy consumption.« less

Designing healthy communities: creating evidence on metrics for built environment features associated with walkable neighbourhood activity centres.

PubMed

Gunn, Lucy Dubrelle; Mavoa, Suzanne; Boulangé, Claire; Hooper, Paula; Kavanagh, Anne; Giles-Corti, Billie

2017-12-04

Evidence-based metrics are needed to inform urban policy to create healthy walkable communities. Most active living research has developed metrics of the environment around residential addresses, ignoring other important walking locations. Therefore, this study examined: metrics for built environment features surrounding local shopping centres, (known in Melbourne, Australia as neighbourhood activity centres (NACs) which are typically anchored by a supermarket); the association between NACs and transport walking; and, policy compliance for supermarket provision. In this observational study, cluster analysis was used to categorize 534 NACs in Melbourne, Australia by their built environment features. The NACS were linked to eligible Victorian Integrated Survey of Travel Activity 2009-2010 (VISTA) survey participants (n=19,984). Adjusted multilevel logistic regressions estimated associations between each cluster typology and two outcomes of daily walking: any transport walking; and, any 'neighbourhood' transport walking. Distance between residential dwellings and closest NAC was assessed to evaluate compliance with local planning policy on supermarket locations. Metrics for 19 built environment features were estimated and three NAC clusters associated with walkability were identified. NACs with significantly higher street connectivity (mean:161, SD:20), destination diversity (mean:16, SD:0.4); and net residential density (mean:77, SD:65) were interpreted as being 'highly walkable' when compared with 'low walkable' NACs, which had lower street connectivity (mean:57, SD:15); destination diversity (mean:11, SD:3); and net residential density (mean:10, SD:3). The odds of any daily transport walking was 5.85 times higher (95% CI: 4.22, 8.11), and for any 'neighborhood' transport walking 8.66 (95% CI: 5.89, 12.72) times higher, for residents whose closest NAC was highly walkable compared with those living near low walkable NACs. Only highly walkable NACs met the policy requirement that residents live within 1km of a local supermarket. Built environment features surrounding NACs must reach certain levels to encourage walking and deliver walkable communities. Research and metrics about the type and quantity of built environment features around both walking trip origins and destinations is needed to inform urban planning policies and urban design guidelines.

Effect of different children's menu labeling designs on family purchases.

PubMed

Holmes, Ashley S; Serrano, Elena L; Machin, Jane E; Duetsch, Thomas; Davis, George C

2013-03-01

The majority of labeling studies at restaurants have focused on adults, not children, and utilized cross-sectional data with one menu labeling design, typically calorie information. The aim of this longitudinal study was to examine the effect of three different menu labeling designs for children's meals on total calories and fat selected by families. Each menu was implemented for 2months. Patrons' purchases were tracked from a control menu (with no nutrition information) through all three theoretically-based designs: calorie and fat information; followed by symbols denoting healthier choices; then nutrition bargain price. All menus were created specifically for the study. They featured six combination meals (pre-determined entrees and side items) and a la carte items (entrees and side items that could be ordered separately). Only combination meals contained labeling. Fixed effects models were estimated to detect changes in sales for each menu labeling design compared to the control. Overall, menu labeling did not result in a positive net effect on total calories or fat purchased by families, but resulted in significant shifts in purchases of combination and a la carte meals and healthy and unhealthy options. The most significant impact was seen for nutrition bargain price labeling, the last design. Copyright © 2012 Elsevier Ltd. All rights reserved.

A design methodology of magentorheological fluid damper using Herschel-Bulkley model

NASA Astrophysics Data System (ADS)

Liao, Linqing; Liao, Changrong; Cao, Jianguo; Fu, L. J.

2003-09-01

Magnetorheological fluid (MR fluid) is highly concentrated suspension of very small magnetic particle in inorganic oil. The essential behavior of MR fluid is its ability to reversibly change from free-flowing, linear viscous liquids to semi-solids having controllable yield strength in milliseconds when exposed to magnetic field. This feature provides simple, quiet, rapid-response interfaces between electronic controls and mechanical systems. In this paper, a mini-bus MR fluid damper based on plate Poiseuille flow mode is typically analyzed using Herschel-Bulkley model, which can be used to account for post-yield shear thinning or thickening under the quasi-steady flow condition. In the light of various value of flow behavior index, the influences of post-yield shear thinning or thickening on flow velocity profiles of MR fluid in annular damping orifice are examined numerically. Analytical damping coefficient predictions also are compared via the nonlinear Bingham plastic model and Herschel-Bulkley constitutive model. A MR fluid damper, which is designed and fabricated according to design method presented in this paper, has tested by electro-hydraulic servo vibrator and its control system in National Center for Test and Supervision of Coach Quality. The experimental results reveal that the analysis methodology and design theory are reasonable and MR fluid damper can be designed according to the design methodology.

Neuron’s eye view: Inferring features of complex stimuli from neural responses

PubMed Central

Chen, Xin; Beck, Jeffrey M.

2017-01-01

Experiments that study neural encoding of stimuli at the level of individual neurons typically choose a small set of features present in the world—contrast and luminance for vision, pitch and intensity for sound—and assemble a stimulus set that systematically varies along these dimensions. Subsequent analysis of neural responses to these stimuli typically focuses on regression models, with experimenter-controlled features as predictors and spike counts or firing rates as responses. Unfortunately, this approach requires knowledge in advance about the relevant features coded by a given population of neurons. For domains as complex as social interaction or natural movement, however, the relevant feature space is poorly understood, and an arbitrary a priori choice of features may give rise to confirmation bias. Here, we present a Bayesian model for exploratory data analysis that is capable of automatically identifying the features present in unstructured stimuli based solely on neuronal responses. Our approach is unique within the class of latent state space models of neural activity in that it assumes that firing rates of neurons are sensitive to multiple discrete time-varying features tied to the stimulus, each of which has Markov (or semi-Markov) dynamics. That is, we are modeling neural activity as driven by multiple simultaneous stimulus features rather than intrinsic neural dynamics. We derive a fast variational Bayesian inference algorithm and show that it correctly recovers hidden features in synthetic data, as well as ground-truth stimulus features in a prototypical neural dataset. To demonstrate the utility of the algorithm, we also apply it to cluster neural responses and demonstrate successful recovery of features corresponding to monkeys and faces in the image set. PMID:28827790

Morphologic, Immunophenotypic, and Molecular Features of Epithelial Ovarian Cancer.

PubMed

Ramalingam, Preetha

2016-02-01

Epithelial ovarian cancer comprises a heterogeneous group of tumors. The four most common subtypes are serous, endometrioid, clear cell, and mucinous carcinoma. Less common are transitional cell tumors, including transitional cell carcinoma and malignant Brenner tumor. While in the past these subtypes were grouped together and designated as epithelial ovarian tumors, these tumor types are now known to be separate entities with distinct clinical and biologic behaviors. From a therapeutic standpoint, current regimens employ standard chemotherapy based on stage and grade rather than histotype. However, this landscape may change in the era of personalized therapy, given that most subtypes (with the exception of high-grade serous carcinoma) are relatively resistant to chemotherapy. It is now well-accepted that high-grade and low-grade serous carcinomas represent distinct entities rather than a spectrum of the same tumor type. While they are similar in that patients present with advanced-stage disease, their histologic and molecular features are entirely different. High-grade serous carcinoma is associated with TP53 mutations, whereas low-grade serous carcinomas are associated with BRAF and KRAS mutations. Endometrioid and clear cell carcinomas typically present as early-stage disease and are frequently associated with endometriosis. Mucinous carcinomas typically present as large unilateral masses and often show areas of mucinous cystadenoma and mucinous borderline tumor. It must be emphasized that primary mucinous carcinomas are uncommon tumors, and metastasis from other sites such as the appendix, colon, stomach, and pancreaticobiliary tract must always be considered in the differential diagnosis. Lastly, transitional cell tumors of the ovary, specifically malignant Brenner tumors, are quite uncommon. High-grade serous carcinoma often has a transitional cell pattern, and adequate sampling in most cases shows more typical areas of serous carcinoma. Immunohistochemical markers are routinely employed in the diagnosis of epithelial ovarian carcinomas. However, molecular testing of these tumors, unlike in endometrial carcinoma, is not routinely used in clinical practice.

Radar returns from ground clutter in vicinity of airports

NASA Technical Reports Server (NTRS)

Raemer, H. R.; Rahgavan, R.; Bhattacharya, A.

1988-01-01

The objective of this project is to develop a dynamic simulation of the received signals from natural and man-made ground features in the vicinity of airports. The simulation is run during landing and takeoff stages of a flight. Vugraphs of noteworthy features of the simulation, ground clutter data bases, the development of algorithms for terrain features, typical wave theory results, and a gravity wave height profile are given.

Kinematic measurements of the vocal-fold displacement waveform in typical children and adult populations: quantification of high-speed endoscopic videos.

PubMed

Patel, Rita; Donohue, Kevin D; Unnikrishnan, Harikrishnan; Kryscio, Richard J

2015-04-01

This article presents a quantitative method for assessing instantaneous and average lateral vocal-fold motion from high-speed digital imaging, with a focus on developmental changes in vocal-fold kinematics during childhood. Vocal-fold vibrations were analyzed for 28 children (aged 5-11 years) and 28 adults (aged 21-45 years) without voice disorders. The following kinematic features were analyzed from the vocal-fold displacement waveforms: relative velocity-based features (normalized average and peak opening and closing velocities), relative acceleration-based features (normalized peak opening and closing accelerations), speed quotient, and normalized peak displacement. Children exhibited significantly larger normalized peak displacements, normalized average and peak opening velocities, normalized average and peak closing velocities, peak opening and closing accelerations, and speed quotient compared to adult women. Values of normalized average closing velocity and speed quotient were higher in children compared to adult men. When compared to adult men, developing children typically have higher estimates of kinematic features related to normalized displacement and its derivatives. In most cases, the kinematic features of children are closer to those of adult men than adult women. Even though boys experience greater changes in glottal length and pitch as they mature, results indicate that girls experience greater changes in kinematic features compared to boys.

A Fault Alarm and Diagnosis Method Based on Sensitive Parameters and Support Vector Machine

NASA Astrophysics Data System (ADS)

Zhang, Jinjie; Yao, Ziyun; Lv, Zhiquan; Zhu, Qunxiong; Xu, Fengtian; Jiang, Zhinong

2015-08-01

Study on the extraction of fault feature and the diagnostic technique of reciprocating compressor is one of the hot research topics in the field of reciprocating machinery fault diagnosis at present. A large number of feature extraction and classification methods have been widely applied in the related research, but the practical fault alarm and the accuracy of diagnosis have not been effectively improved. Developing feature extraction and classification methods to meet the requirements of typical fault alarm and automatic diagnosis in practical engineering is urgent task. The typical mechanical faults of reciprocating compressor are presented in the paper, and the existing data of online monitoring system is used to extract fault feature parameters within 15 types in total; the inner sensitive connection between faults and the feature parameters has been made clear by using the distance evaluation technique, also sensitive characteristic parameters of different faults have been obtained. On this basis, a method based on fault feature parameters and support vector machine (SVM) is developed, which will be applied to practical fault diagnosis. A better ability of early fault warning has been proved by the experiment and the practical fault cases. Automatic classification by using the SVM to the data of fault alarm has obtained better diagnostic accuracy.

Comparing Pattern Recognition Feature Sets for Sorting Triples in the FIRST Database

NASA Astrophysics Data System (ADS)

Proctor, D. D.

2006-07-01

Pattern recognition techniques have been used with increasing success for coping with the tremendous amounts of data being generated by automated surveys. Usually this process involves construction of training sets, the typical examples of data with known classifications. Given a feature set, along with the training set, statistical methods can be employed to generate a classifier. The classifier is then applied to process the remaining data. Feature set selection, however, is still an issue. This paper presents techniques developed for accommodating data for which a substantive portion of the training set cannot be classified unambiguously, a typical case for low-resolution data. Significance tests on the sort-ordered, sample-size-normalized vote distribution of an ensemble of decision trees is introduced as a method of evaluating relative quality of feature sets. The technique is applied to comparing feature sets for sorting a particular radio galaxy morphology, bent-doubles, from the Faint Images of the Radio Sky at Twenty Centimeters (FIRST) database. Also examined are alternative functional forms for feature sets. Associated standard deviations provide the means to evaluate the effect of the number of folds, the number of classifiers per fold, and the sample size on the resulting classifications. The technique also may be applied to situations for which, although accurate classifications are available, the feature set is clearly inadequate, but is desired nonetheless to make the best of available information.

Designing Input Fields for Non-Narrative Open-Ended Responses in Web Surveys

PubMed Central

Couper, Mick P.; Kennedy, Courtney; Conrad, Frederick G.; Tourangeau, Roger

2012-01-01

Web surveys often collect information such as frequencies, currency amounts, dates, or other items requiring short structured answers in an open-ended format, typically using text boxes for input. We report on several experiments exploring design features of such input fields. We find little effect of the size of the input field on whether frequency or dollar amount answers are well-formed or not. By contrast, the use of templates to guide formatting significantly improves the well-formedness of responses to questions eliciting currency amounts. For date questions (whether month/year or month/day/year), we find that separate input fields improve the quality of responses over single input fields, while drop boxes further reduce the proportion of ill-formed answers. Drop boxes also reduce completion time when the list of responses is short (e.g., months), but marginally increases completion time when the list is long (e.g., birth dates). These results suggest that non-narrative open questions can be designed to help guide respondents to provide answers in the desired format. PMID:23411468

Interactions between hyporheic flow produced by stream meanders, bars, and dunes

USGS Publications Warehouse

Stonedahl, Susa H.; Harvey, Judson W.; Packman, Aaron I.

2013-01-01

Stream channel morphology from grain-scale roughness to large meanders drives hyporheic exchange flow. In practice, it is difficult to model hyporheic flow over the wide spectrum of topographic features typically found in rivers. As a result, many studies only characterize isolated exchange processes at a single spatial scale. In this work, we simulated hyporheic flows induced by a range of geomorphic features including meanders, bars and dunes in sand bed streams. Twenty cases were examined with 5 degrees of river meandering. Each meandering river model was run initially without any small topographic features. Models were run again after superimposing only bars and then only dunes, and then run a final time after including all scales of topographic features. This allowed us to investigate the relative importance and interactions between flows induced by different scales of topography. We found that dunes typically contributed more to hyporheic exchange than bars and meanders. Furthermore, our simulations show that the volume of water exchanged and the distributions of hyporheic residence times resulting from various scales of topographic features are close to, but not linearly additive. These findings can potentially be used to develop scaling laws for hyporheic flow that can be widely applied in streams and rivers.

BioTAP: A Systematic Approach to Teaching Scientific Writing and Evaluating Undergraduate Theses

ERIC Educational Resources Information Center

Reynolds, Julie; Smith, Robin; Moskovitz, Cary; Sayle, Amy

2009-01-01

Undergraduate theses and other capstone research projects are standard features of many science curricula, but participation has typically been limited to only the most advanced and highly motivated students. With the recent push to engage more undergraduates in research, some faculty are finding that their typical approach to working with thesis…

Comparative study on the efficiency of some optical methods for artwork diagnostics

NASA Astrophysics Data System (ADS)

Schirripa Spagnolo, Giuseppe; Ambrosini, Dario; Paoletti, Domenica

2001-10-01

Scientific investigation methods are founding their place besides the stylistic-historical study methods in art research works. In particular, optical techniques, transferred from other fields or developed ad hoc, can make a strong contribution to the safeguarding and exploitation of cultural heritage. This paper describes the use of different optical techniques, such as holographic interferometry, decorrelation, shearography and ESPI, in the diagnostics of works of art. A comparison between different methods is obtained by performing tests on specially designed models, prepared using typical techniques and materials. Inside the model structure, a number of defects of known types, form and extension are inserted. The different features of each technique are outlined and a comparison with IR thermography is also carried out.

Nitric Oxide Reduction over Sewage Sludge and Coal Chars at Conditions Relevant to Staged Fluidized Bed Combustion

NASA Astrophysics Data System (ADS)

Salatino, P.; Solimene, R.; Chirone, R.

The de-NOx potential of coal and of dried and pelletized sewage sludge, a waste-derived fuel candidate for cofiring with coal, is assessed. The experimental procedure is based on operation of a bench scale fluidized bed reactor where NO-doped nitrogen is contacted with batches of the fuel. A second type of experiment has been purposely designed to assess the loss of reactivity of chars toward gasification by NOx as char is heat-treated for pre-set times at temperatures typical of fluidized bed combustion. A simple phenomenological model is developed to shed light on the basic features of the interaction between heterogeneous char-NOx reaction and thermal annealing of the char.

Observations in the solar spectrum interest for remote sensing purposes

NASA Technical Reports Server (NTRS)

Herman, M.; Vanderbilt, V.

1994-01-01

The polarization of the sunlight scattered by atmospheric aerosols or cloud droplets and reflected from ground surfaces or plant canopies may convey much information when used for remote sensing purposes. The typical polarization features of aerosols, cloud droplets, and plant canopies, as observed by ground based and airborne sensors, are investigated, looking especially for those invariant properties amenable to description by simple models when possible. The question of polarization measurements from space is addressed. The interest of such measurements for remote sensing purposes is investigated, and their feasibility is tested by using results obtained during field campaigns of the airborne POLDER instrument, a radiometer designed to measure the directionality and polarization of the sunlight scattered by the ground atmosphere system.

Scale invariance in natural and artificial collective systems: a review

PubMed Central

Huepe, Cristián

2017-01-01

Self-organized collective coordinated behaviour is an impressive phenomenon, observed in a variety of natural and artificial systems, in which coherent global structures or dynamics emerge from local interactions between individual parts. If the degree of collective integration of a system does not depend on size, its level of robustness and adaptivity is typically increased and we refer to it as scale-invariant. In this review, we first identify three main types of self-organized scale-invariant systems: scale-invariant spatial structures, scale-invariant topologies and scale-invariant dynamics. We then provide examples of scale invariance from different domains in science, describe their origins and main features and discuss potential challenges and approaches for designing and engineering artificial systems with scale-invariant properties. PMID:29093130

A 15,000-hour cyclic endurance test of an 8-centimeter-diameter electron bombardment mercury ion thruster

NASA Technical Reports Server (NTRS)

Nakanishi, S.

1976-01-01

A laboratory model 8 cm thruster with improvements to minimize ion chamber erosion and peeling of sputtered metal was subjected to a cyclic endurance test for 15,040 hours and 460 restarts. A charted history of several thruster operating variables and off-normal events are shown in 600-hour segments at three points in the test. The transient behavior of these variables during a typical start-stop cycle is presented. Finding of the post-test inspection confirmed most of the expected results. Charge exchange ions caused normal accelerator grid erosion. The workability of the various design features was substantiated, and attainable improvements in propellant utilization efficiency should significantly reduce accelerator erosion.

Visuospatial, visuoperceptual, and visuoconstructive abilities in congenital hypothyroidism.

PubMed

Simic, Nevena; Khan, Sarah; Rovet, Joanne

2013-11-01

Individuals with congenital hypothyroidism (CH), even those diagnosed and treated early, experience selective cognitive deficits, the most striking of which involves the visuocognitive domain. However, the range and nature of their visuocognitive disturbances is not fully understood. We assessed a range of higher-order visuocognitive abilities in 19 children and adolescents with CH and 19 age- and sex-matched typically developing peers (TD) using a battery of neuropsychological tests and a novel self-report measure of sense of direction. CH scored lower than TD on direct tests of visuocognitive function (judging line orientation, parts-to-whole localization, copying three-dimensional block towers, discriminating designs, and matching unfamiliar faces in ¾ profile-view) as well as on self-reported problems in spatial ability. Visuocognitive problems were not global as CH and TD did not differ at copying two-dimensional block designs, mentally rotating and matching abstract shapes, or at matching unfamiliar front-view faces, design features, or designs that engaged either figure-ground segregation, visual constancy, or closure. Early and concurrent thyroid stimulating hormone (TSH) levels were associated with visuocognitive ability, although attention and working memory were not. Individuals with CH exhibit selective visuocognitive weaknesses, some of which are related to early and concurrent TSH levels.

Session 6: Dynamic Modeling and Systems Analysis

NASA Technical Reports Server (NTRS)

Csank, Jeffrey; Chapman, Jeffryes; May, Ryan

2013-01-01

These presentations cover some of the ongoing work in dynamic modeling and dynamic systems analysis. The first presentation discusses dynamic systems analysis and how to integrate dynamic performance information into the systems analysis. The ability to evaluate the dynamic performance of an engine design may allow tradeoffs between the dynamic performance and operability of a design resulting in a more efficient engine design. The second presentation discusses the Toolbox for Modeling and Analysis of Thermodynamic Systems (T-MATS). T-MATS is a Simulation system with a library containing the basic building blocks that can be used to create dynamic Thermodynamic Systems. Some of the key features include Turbo machinery components, such as turbines, compressors, etc., and basic control system blocks. T-MAT is written in the Matlab-Simulink environment and is open source software. The third presentation focuses on getting additional performance from the engine by allowing the limit regulators only to be active when a limit is danger of being violated. Typical aircraft engine control architecture is based on MINMAX scheme, which is designed to keep engine operating within prescribed mechanical/operational safety limits. Using a conditionally active min-max limit regulator scheme, additional performance can be gained by disabling non-relevant limit regulators

Fault-tolerant feature-based estimation of space debris rotational motion during active removal missions

NASA Astrophysics Data System (ADS)

Biondi, Gabriele; Mauro, Stefano; Pastorelli, Stefano; Sorli, Massimo

2018-05-01

One of the key functionalities required by an Active Debris Removal mission is the assessment of the target kinematics and inertial properties. Passive sensors, such as stereo cameras, are often included in the onboard instrumentation of a chaser spacecraft for capturing sequential photographs and for tracking features of the target surface. A plenty of methods, based on Kalman filtering, are available for the estimation of the target's state from feature positions; however, to guarantee the filter convergence, they typically require continuity of measurements and the capability of tracking a fixed set of pre-defined features of the object. These requirements clash with the actual tracking conditions: failures in feature detection often occur and the assumption of having some a-priori knowledge about the shape of the target could be restrictive in certain cases. The aim of the presented work is to propose a fault-tolerant alternative method for estimating the angular velocity and the relative magnitudes of the principal moments of inertia of the target. Raw data regarding the positions of the tracked features are processed to evaluate corrupted values of a 3-dimentional parameter which entirely describes the finite screw motion of the debris and which primarily is invariant on the particular set of considered features of the object. Missing values of the parameter are completely restored exploiting the typical periodicity of the rotational motion of an uncontrolled satellite: compressed sensing techniques, typically adopted for recovering images or for prognostic applications, are herein used in a completely original fashion for retrieving a kinematic signal that appears sparse in the frequency domain. Due to its invariance about the features, no assumptions are needed about the target's shape and continuity of the tracking. The obtained signal is useful for the indirect evaluation of an attitude signal that feeds an unscented Kalman filter for the estimation of the global rotational state of the target. The results of the computer simulations showed a good robustness of the method and its potential applicability for general motion conditions of the target.

Tracking subtle stereotypes of children with trisomy 21: from facial-feature-based to implicit stereotyping.

PubMed

Enea-Drapeau, Claire; Carlier, Michèle; Huguet, Pascal

2012-01-01

Stigmatization is one of the greatest obstacles to the successful integration of people with Trisomy 21 (T21 or Down syndrome), the most frequent genetic disorder associated with intellectual disability. Research on attitudes and stereotypes toward these people still focuses on explicit measures subjected to social-desirability biases, and neglects how variability in facial stigmata influences attitudes and stereotyping. The participants were 165 adults including 55 young adult students, 55 non-student adults, and 55 professional caregivers working with intellectually disabled persons. They were faced with implicit association tests (IAT), a well-known technique whereby response latency is used to capture the relative strength with which some groups of people--here photographed faces of typically developing children and children with T21--are automatically (without conscious awareness) associated with positive versus negative attributes in memory. Each participant also rated the same photographed faces (consciously accessible evaluations). We provide the first evidence that the positive bias typically found in explicit judgments of children with T21 is smaller for those whose facial features are highly characteristic of this disorder, compared to their counterparts with less distinctive features and to typically developing children. We also show that this bias can coexist with negative evaluations at the implicit level (with large effect sizes), even among professional caregivers. These findings support recent models of feature-based stereotyping, and more importantly show how crucial it is to go beyond explicit evaluations to estimate the true extent of stigmatization of intellectually disabled people.

Improved Steam Turbine Leakage Control with a Brush Seal Design

NASA Astrophysics Data System (ADS)

Turnquist, Norman; Chupp, Raymond E.; Pastrana, Ryan; Wolfe, Chris; Burnett, Mark

2002-10-01

This paper presents an improved steam turbine leakage control system with a brush seal design. The contents include: 1) Typical Design Characteristics; 2) Typical Brush Seal Locations; 3) Reduced Leakage Rates; 4) Performance Benefits; 5) System Considerations; 6) Rotor Dynamics; 7) Laboratory Tests and 8) Field Experience.

Acoustic Mechanical Feedthroughs

NASA Technical Reports Server (NTRS)

Sherrit, Stewart; Walkemeyer, Phillip; Bao, Xiaoqi; Bar-Cohen, Yoseph; Badescu, Mircea

2013-01-01

Electromagnetic motors can have problems when operating in extreme environments. In addition, if one needs to do mechanical work outside a structure, electrical feedthroughs are required to transport the electric power to drive the motor. In this paper, we present designs for driving rotary and linear motors by pumping stress waves across a structure or barrier. We accomplish this by designing a piezoelectric actuator on one side of the structure and a resonance structure that is matched to the piezoelectric resonance of the actuator on the other side. Typically, piezoelectric motors can be designed with high torques and lower speeds without the need for gears. One can also use other actuation materials such as electrostrictive, or magnetostrictive materials in a benign environment and transmit the power in acoustic form as a stress wave and actuate mechanisms that are external to the benign environment. This technology removes the need to perforate a structure and allows work to be done directly on the other side of a structure without the use of electrical feedthroughs, which can weaken the structure, pipe, or vessel. Acoustic energy is pumped as a stress wave at a set frequency or range of frequencies to produce rotary or linear motion in a structure. This method of transferring useful mechanical work across solid barriers by pumping acoustic energy through a resonant structure features the ability to transfer work (rotary or linear motion) across pressure or thermal barriers, or in a sterile environment, without generating contaminants. Reflectors in the wall of barriers can be designed to enhance the efficiency of the energy/power transmission. The method features the ability to produce a bi-directional driving mechanism using higher-mode resonances. There are a variety of applications where the presence of a motor is complicated by thermal or chemical environments that would be hostile to the motor components and reduce life and, in some instances, not be feasible. A variety of designs that have been designed, fabricated and tested will be presented

Temporary brittle bone disease: fractures in medical care.

PubMed

Paterson, Colin R

2009-12-01

Temporary brittle bone disease is the name given to a syndrome first reported in 1990, in which fractures occur in infants in the first year of life. The fractures include rib fractures and metaphyseal fractures which are mostly asymptomatic. The radiological features of this disorder mimic those often ascribed to typical non-accidental injury. The subject has been controversial, some authors suggesting that the disorder does not exist. This study reports five infants with typical features of temporary brittle bone disease in whom all or most of the fractures took place while in hospital. A non-accidental cause can be eliminated with some confidence, and these cases provide evidence in support of the existence of temporary brittle bone disease.

Guillain-Barre syndrome associated with peginterferon alfa-2a for chronic hepatitis C: A case report

PubMed Central

Niazi, Mumtaz A; Azhar, Ashaur; Tufail, Kashif; Feyssa, Eyob L; Penny, Stephen F; McGregory, Marlene; Araya, Victor; Ortiz, Jorge A

2010-01-01

The recommended therapy for chronic hepatitis C (CHC) infection is the combination of a Pegylated interferon and Ribavirin. Almost all such patients on combination therapy experience one or more adverse events during the course of treatment. Significant neurological side effects are rare. A few cases of Bell’s Palsy, chronic inflammatory demyelinating polyneuropathy and even one case of acute demyelinating polyneuropathy with atypical features for Guillain-Barre syndrome (GBS) associated with Interferon therapy have been reported but no report of GBS with typical features has been published. We present a case report of typical GBS associated with Peginterferon alfa-2a and Ribavirin used for treatment of CHC infection. PMID:21160989

Gender discrimination of eyes and mouths by individuals with autism.

PubMed

Best, Catherine A; Minshew, Nancy J; Strauss, Mark S

2010-04-01

Evidence remains mixed about whether individuals with autism look less to eyes and whether they look more at mouths. Few studies have examined how spontaneous attention to facial features relates to face processing abilities. This study tested the ability to discriminate gender from facial features, namely eyes and mouths, by comparing accuracy scores of 17 children with autism and 15 adults with autism to 17 typically developing children and 15 typically developing adults. Results indicated that all participants regardless of diagnosis discriminated gender more accurately from eyes than from mouths. However, results indicated that compared to adults without autism, adults with autism were significantly worse at discriminating gender from eyes.

Rules versus Prototype Matching: Strategies of Perception of Emotional Facial Expressions in the Autism Spectrum

ERIC Educational Resources Information Center

Rutherford, M. D.; McIntosh, Daniel N.

2007-01-01

When perceiving emotional facial expressions, people with autistic spectrum disorders (ASD) appear to focus on individual facial features rather than configurations. This paper tests whether individuals with ASD use these features in a rule-based strategy of emotional perception, rather than a typical, template-based strategy by considering…

Autoscoring Essays Based on Complex Networks

ERIC Educational Resources Information Center

Ke, Xiaohua; Zeng, Yongqiang; Luo, Haijiao

2016-01-01

This article presents a novel method, the Complex Dynamics Essay Scorer (CDES), for automated essay scoring using complex network features. Texts produced by college students in China were represented as scale-free networks (e.g., a word adjacency model) from which typical network features, such as the in-/out-degrees, clustering coefficient (CC),…

Ghost Hunting as a Means to Illustrate Scientific Methodology and Enhance Critical Thinking

ERIC Educational Resources Information Center

Rockwell, Steven C.

2012-01-01

The increasing popularity of television shows featuring paranormal investigations has led to a renewed enthusiasm in ghost hunting activities, and belief in the paranormal in general. These shows typically feature a group of investigators who, while claiming to utilize proper scientifically correct methodologies, violate many core scientific…

Seeing Deep Structure from the Interactions of Surface Features

ERIC Educational Resources Information Center

Chi, Michelene T. H.; VanLehn, Kurt A.

2012-01-01

Transfer is typically thought of as requiring individuals to "see" what is the same in the deep structure between a new target problem and a previously encountered source problem, even though the surface features may be dissimilar. We propose that experts can "see" the deep structure by considering the first-order interactions…

Histopathology of acute acalculous cholecystitis in critically ill patients.

PubMed

Laurila, J J; Ala-Kokko, T I; Laurila, P A; Saarnio, J; Koivukangas, V; Syrjälä, H; Karttunen, T J

2005-11-01

To illustrate the histopathological features of acute acalculous cholecystitis (AAC) of critically ill patients and to compare them with those of acute calculous cholecystitis (ACC) and normal gallbladders. We studied 34 gallbladders with AAC and compared them with 28 cases of ACC and 14 normal gallbladders. Histological features were systematically evaluated. Typical features in AAC were bile infiltration, leucocyte margination of blood vessels and lymphatic dilation. Bile infiltration in the gallbladder wall was more common and extended wider and deeper into the muscle layer in AAC compared with ACC. Epithelial degeneration and defects and widespread occurrence of inflammatory cells were typical features in ACC. Necrosis in the muscle layer was also more common and extended wider and deeper in ACC. There were no differences in the occurrence of capillary thromboses, lymphatic follicles or Rokitansky-Aschoff sinuses between the AAC and ACC samples. There are characteristic differences in histopathology between AAC and ACC, although due to overlap, none appeared to be specific as such for either condition. These results suggest that AAC is largely a manifestation of systemic critical illness, whereas ACC is a local disease of the gallbladder.

Flight Software Math Library

NASA Technical Reports Server (NTRS)

McComas, David

2013-01-01

The flight software (FSW) math library is a collection of reusable math components that provides typical math utilities required by spacecraft flight software. These utilities are intended to increase flight software quality reusability and maintainability by providing a set of consistent, well-documented, and tested math utilities. This library only has dependencies on ANSI C, so it is easily ported. Prior to this library, each mission typically created its own math utilities using ideas/code from previous missions. Part of the reason for this is that math libraries can be written with different strategies in areas like error handling, parameters orders, naming conventions, etc. Changing the utilities for each mission introduces risks and costs. The obvious risks and costs are that the utilities must be coded and revalidated. The hidden risks and costs arise in miscommunication between engineers. These utilities must be understood by both the flight software engineers and other subsystem engineers (primarily guidance navigation and control). The FSW math library is part of a larger goal to produce a library of reusable Guidance Navigation and Control (GN&C) FSW components. A GN&C FSW library cannot be created unless a standardized math basis is created. This library solves the standardization problem by defining a common feature set and establishing policies for the library s design. This allows the libraries to be maintained with the same strategy used in its initial development, which supports a library of reusable GN&C FSW components. The FSW math library is written for an embedded software environment in C. This places restrictions on the language features that can be used by the library. Another advantage of the FSW math library is that it can be used in the FSW as well as other environments like the GN&C analyst s simulators. This helps communication between the teams because they can use the same utilities with the same feature set and syntax.

MANTA--an open-source, high density electrophysiology recording suite for MATLAB.

PubMed

Englitz, B; David, S V; Sorenson, M D; Shamma, S A

2013-01-01

The distributed nature of nervous systems makes it necessary to record from a large number of sites in order to decipher the neural code, whether single cell, local field potential (LFP), micro-electrocorticograms (μECoG), electroencephalographic (EEG), magnetoencephalographic (MEG) or in vitro micro-electrode array (MEA) data are considered. High channel-count recordings also optimize the yield of a preparation and the efficiency of time invested by the researcher. Currently, data acquisition (DAQ) systems with high channel counts (>100) can be purchased from a limited number of companies at considerable prices. These systems are typically closed-source and thus prohibit custom extensions or improvements by end users. We have developed MANTA, an open-source MATLAB-based DAQ system, as an alternative to existing options. MANTA combines high channel counts (up to 1440 channels/PC), usage of analog or digital headstages, low per channel cost (<$90/channel), feature-rich display and filtering, a user-friendly interface, and a modular design permitting easy addition of new features. MANTA is licensed under the GPL and free of charge. The system has been tested by daily use in multiple setups for >1 year, recording reliably from 128 channels. It offers a growing list of features, including integrated spike sorting, PSTH and CSD display and fully customizable electrode array geometry (including 3D arrays), some of which are not available in commercial systems. MANTA runs on a typical PC and communicates via TCP/IP and can thus be easily integrated with existing stimulus generation/control systems in a lab at a fraction of the cost of commercial systems. With modern neuroscience developing rapidly, MANTA provides a flexible platform that can be rapidly adapted to the needs of new analyses and questions. Being open-source, the development of MANTA can outpace commercial solutions in functionality, while maintaining a low price-point.

MANTA—an open-source, high density electrophysiology recording suite for MATLAB

PubMed Central

Englitz, B.; David, S. V.; Sorenson, M. D.; Shamma, S. A.

2013-01-01

The distributed nature of nervous systems makes it necessary to record from a large number of sites in order to decipher the neural code, whether single cell, local field potential (LFP), micro-electrocorticograms (μECoG), electroencephalographic (EEG), magnetoencephalographic (MEG) or in vitro micro-electrode array (MEA) data are considered. High channel-count recordings also optimize the yield of a preparation and the efficiency of time invested by the researcher. Currently, data acquisition (DAQ) systems with high channel counts (>100) can be purchased from a limited number of companies at considerable prices. These systems are typically closed-source and thus prohibit custom extensions or improvements by end users. We have developed MANTA, an open-source MATLAB-based DAQ system, as an alternative to existing options. MANTA combines high channel counts (up to 1440 channels/PC), usage of analog or digital headstages, low per channel cost (<$90/channel), feature-rich display and filtering, a user-friendly interface, and a modular design permitting easy addition of new features. MANTA is licensed under the GPL and free of charge. The system has been tested by daily use in multiple setups for >1 year, recording reliably from 128 channels. It offers a growing list of features, including integrated spike sorting, PSTH and CSD display and fully customizable electrode array geometry (including 3D arrays), some of which are not available in commercial systems. MANTA runs on a typical PC and communicates via TCP/IP and can thus be easily integrated with existing stimulus generation/control systems in a lab at a fraction of the cost of commercial systems. With modern neuroscience developing rapidly, MANTA provides a flexible platform that can be rapidly adapted to the needs of new analyses and questions. Being open-source, the development of MANTA can outpace commercial solutions in functionality, while maintaining a low price-point. PMID:23653593

The epileptology of Koolen-de Vries syndrome: Electro-clinico-radiologic findings in 31 patients.

PubMed

Myers, Kenneth A; Mandelstam, Simone A; Ramantani, Georgia; Rushing, Elisabeth J; de Vries, Bert B; Koolen, David A; Scheffer, Ingrid E

2017-06-01

This study was designed to describe the spectrum of epilepsy phenotypes in Koolen-de Vries syndrome (KdVS), a genetic syndrome involving dysmorphic features, intellectual disability, hypotonia, and congenital malformations, that occurs secondary to 17q21.31 microdeletions and heterozygous mutations in KANSL1. We were invited to attend a large gathering of individuals with KdVS and their families. While there, we recruited individuals with KdVS and seizures, and performed thorough phenotyping. Additional subjects were included who approached us after the family support group brought attention to our research via social media. Inclusion criteria were genetic testing results demonstrating 17q21.31 deletion or KANSL1 mutation, and at least one seizure. Thirty-one individuals were studied, aged 2-35 years. Median age at seizure onset was 3.5 years, and 9 of 22 had refractory seizures 2 years after onset. Focal impaired awareness seizures were the most frequent seizure type occurring in 20 of 31, usually with prominent autonomic features. Twenty-one patients had prolonged seizures and, at times, refractory status epilepticus. Electroencephalography (EEG) showed focal/multifocal epileptiform discharges in 20 of 26. MRI studies of 13 patients were reviewed, and all had structural anomalies. Corpus callosum dysgenesis, abnormal hippocampi, and dilated ventricles were the most common, although periventricular nodular heterotopia, focal cortical dysplasia, abnormal sulcation, and brainstem and cerebellum abnormalities were also observed. One patient underwent epilepsy surgery for a lesion that proved to be an angiocentric glioma. The typical epilepsy phenotype of KdVS involves childhood-onset focal seizures that are prolonged and have prominent autonomic features. Multifocal epileptiform discharges are the typical EEG pattern. Structural brain abnormalities may be universal, including signs of abnormal neuroblast migration and abnormal axonal guidance. Epilepsy surgery should be undertaken with care given the widespread neuroanatomic abnormalities; however, tumors are a rare, yet important, occurrence. Wiley Periodicals, Inc. © 2017 International League Against Epilepsy.

Designing action games for appealing to buyers.

PubMed

Hsu, Shang Hwa; Lee, Feng-Liang; Wu, Muh-Cherng

2005-12-01

This study aims to identify design features for action games that would appeal to game-buyers, rather than game-players. Sixteen frequent-buyers of computer games identified 39 design features that appeal to buyers by contrasting different versions of Pacman games. Twenty-eight versions of Pacman were then evaluated in terms of the identified design features by 45 participants (27 male and 18 female college students). Qnet2000 neural network software was used to determine the relative importance of these design features. The results indicated that the top 10 most important design features could account for more than 50% of "perceived fun" among these 39 design features. The feature of avatar is important to game-buyers, yet not revealed in previous player-oriented studies. Moreover, six design factors underlying the 39 features were identified through factor analysis. These factors included "novelty and powerfulness," "appealing presentation," "interactivity," "challenging," "sense of control," and "rewarding," and could account for 54% of total variance. Among these six factors, appealing presentation has not been emphasized by player-oriented research. Implications of the findings were discussed.

Research on the Mechanical Properties of a Glass Fiber Reinforced Polymer-Steel Combined Truss Structure

PubMed Central

Liu, Pengfei; Zhao, Qilin; Li, Fei; Liu, Jinchun; Chen, Haosen

2014-01-01

An assembled plane truss structure used for vehicle loading is designed and manufactured. In the truss, the glass fiber reinforced polymer (GFRP) tube and the steel joint are connected by a new technology featuring a pretightened tooth connection. The detailed description for the rod and node design is introduced in this paper, and a typical truss panel is fabricated. Under natural conditions, the short-term load test and long-term mechanical performance test for one year are performed to analyze its performance and conduct a comparative analysis for a reasonable FEM model. The study shows that the design and fabrication for the node of an assembled truss panel are convenient, safe, and reliable; because of the creep control design of the rods, not only does the short-term structural stiffness meet the design requirement but also the long-term creep deformation tends towards stability. In addition, no significant change is found in the elastic modules, so this structure can be applied in actual engineering. Although the safety factor for the strength of the composite rods is very large, it has a lightweight advantage over the steel truss for the low density of GFRP. In the FEM model, simplifying the node as a hinge connection relatively conforms to the actual status. PMID:25247203

Interferometer for measuring the dynamic surface topography of a human tear film

NASA Astrophysics Data System (ADS)

Primeau, Brian C.; Greivenkamp, John E.

2012-03-01

The anterior refracting surface of the eye is the thin tear film that forms on the surface of the cornea. Following a blink, the tear film quickly smoothes and starts to become irregular after 10 seconds. This irregularity can affect comfort and vision quality. An in vivo method of characterizing dynamic tear films has been designed based upon a near-infrared phase-shifting interferometer. This interferometer continuously measures light reflected from the tear film, allowing sub-micron analysis of the dynamic surface topography. Movies showing the tear film behavior can be generated along with quantitative metrics describing changes in the tear film surface. This tear film measurement allows analysis beyond capabilities of typical fluorescein visual inspection or corneal topography and provides better sensitivity and resolution than shearing interferometry methods. The interferometer design is capable of identifying features in the tear film much less than a micron in height with a spatial resolution of about ten microns over a 6 mm diameter. This paper presents the design of the tear film interferometer along with the considerations that must be taken when designing an interferometer for on-eye diagnostics. Discussions include eye movement, design of null optics for a range of ocular geometries, and laser emission limits for on-eye interferometry.

Experimental high-speed network

NASA Astrophysics Data System (ADS)

McNeill, Kevin M.; Klein, William P.; Vercillo, Richard; Alsafadi, Yasser H.; Parra, Miguel V.; Dallas, William J.

1993-09-01

Many existing local area networking protocols currently applied in medical imaging were originally designed for relatively low-speed, low-volume networking. These protocols utilize small packet sizes appropriate for text based communication. Local area networks of this type typically provide raw bandwidth under 125 MHz. These older network technologies are not optimized for the low delay, high data traffic environment of a totally digital radiology department. Some current implementations use point-to-point links when greater bandwidth is required. However, the use of point-to-point communications for a total digital radiology department network presents many disadvantages. This paper describes work on an experimental multi-access local area network called XFT. The work includes the protocol specification, and the design and implementation of network interface hardware and software. The protocol specifies the Physical and Data Link layers (OSI layers 1 & 2) for a fiber-optic based token ring providing a raw bandwidth of 500 MHz. The protocol design and implementation of the XFT interface hardware includes many features to optimize image transfer and provide flexibility for additional future enhancements which include: a modular hardware design supporting easy portability to a variety of host system buses, a versatile message buffer design providing 16 MB of memory, and the capability to extend the raw bandwidth of the network to 3.0 GHz.

Analysis of novel low specific speed pump designs

NASA Astrophysics Data System (ADS)

Klas, R.; Pochylý, F.; Rudolf, P.

2014-03-01

Centrifugal pumps with very low specific speed present significant design challenges. Narrow blade channels, large surface area of hub and shroud discs relative to the blade area, and the presence of significant of blade channel vortices are typical features linked with the difficulty to achieve head and efficiency requirements for such designs. This paper presents an investigation of two novel designs of very low specific speed impellers: impeller having blades with very thick trailing edges and impeller with thick trailing edges and recirculating channels, which are bored along the impeller circumference. Numerical simulations and experimental measurements were used to study the flow dynamics of those new designs. It was shown that thick trailing edges suppress local eddies in the blade channels and decrease energy dissipation due to excessive swirling. Furthermore the recirculating channels will increase the circumferential velocity component on impeller outlet thus increasing the specific energy, albeit adversely affecting the hydraulic efficiency. Analysis of the energy dissipation in the volute showed that the number of the recirculating channels, their geometry and location, all have significant impact on the magnitude of dissipated energy and its distribution which in turn influences the shape of the head curve and the stability of the pump operation. Energy dissipation within whole pump interior (blade channels, volute, rotor- stator gaps) was also studied.

Research on the mechanical properties of a glass fiber reinforced polymer-steel combined truss structure.

PubMed

Liu, Pengfei; Zhao, Qilin; Li, Fei; Liu, Jinchun; Chen, Haosen

2014-01-01

An assembled plane truss structure used for vehicle loading is designed and manufactured. In the truss, the glass fiber reinforced polymer (GFRP) tube and the steel joint are connected by a new technology featuring a pretightened tooth connection. The detailed description for the rod and node design is introduced in this paper, and a typical truss panel is fabricated. Under natural conditions, the short-term load test and long-term mechanical performance test for one year are performed to analyze its performance and conduct a comparative analysis for a reasonable FEM model. The study shows that the design and fabrication for the node of an assembled truss panel are convenient, safe, and reliable; because of the creep control design of the rods, not only does the short-term structural stiffness meet the design requirement but also the long-term creep deformation tends towards stability. In addition, no significant change is found in the elastic modules, so this structure can be applied in actual engineering. Although the safety factor for the strength of the composite rods is very large, it has a lightweight advantage over the steel truss for the low density of GFRP. In the FEM model, simplifying the node as a hinge connection relatively conforms to the actual status.

In Vivo Measurement of Pediatric Vocal Fold Motion Using Structured Light Laser Projection

PubMed Central

Patel, Rita R.; Donohue, Kevin D.; Lau, Daniel; Unnikrishnan, Harikrishnan

2013-01-01

Summary Objective The aim of the study was to present the development of a miniature structured light laser projection endoscope and to quantify vocal fold length and vibratory features related to impact stress of the pediatric glottis using high-speed imaging. Study Design The custom-developed laser projection system consists of a green laser with a 4-mm diameter optics module at the tip of the endoscope, projecting 20 vertical laser lines on the glottis. Measurements of absolute phonatory vocal fold length, membranous vocal fold length, peak amplitude, amplitude-to-length ratio, average closing velocity, and impact velocity were obtained in five children (6–9 years), two adult male and three adult female participants without voice disorders, and one child (10 years) with bilateral vocal fold nodules during modal phonation. Results Independent measurements made on the glottal length of a vocal fold phantom demonstrated a 0.13 mm bias error with a standard deviation of 0.23 mm, indicating adequate precision and accuracy for measuring vocal fold structures and displacement. First, in vivo measurements of amplitude-to-length ratio, peak closing velocity, and impact velocity during phonation in pediatric population and a child with vocal fold nodules are reported. Conclusion The proposed laser projection system can be used to obtain in vivo measurements of absolute length and vibratory features in children and adults. Children have large amplitude-to-length ratio compared with typically developing adults, whereas nodules result in larger peak amplitude, amplitude-to-length ratio, average closing velocity, and impact velocity compared with typically developing children. PMID:23809569

SpaceCube v2.0 Space Flight Hybrid Reconfigurable Data Processing System

NASA Technical Reports Server (NTRS)

Petrick, Dave

2014-01-01

This paper details the design architecture, design methodology, and the advantages of the SpaceCube v2.0 high performance data processing system for space applications. The purpose in building the SpaceCube v2.0 system is to create a superior high performance, reconfigurable, hybrid data processing system that can be used in a multitude of applications including those that require a radiation hardened and reliable solution. The SpaceCube v2.0 system leverages seven years of board design, avionics systems design, and space flight application experiences. This paper shows how SpaceCube v2.0 solves the increasing computing demands of space data processing applications that cannot be attained with a standalone processor approach.The main objective during the design stage is to find a good system balance between power, size, reliability, cost, and data processing capability. These design variables directly impact each other, and it is important to understand how to achieve a suitable balance. This paper will detail how these critical design factors were managed including the construction of an Engineering Model for an experiment on the International Space Station to test out design concepts. We will describe the designs for the processor card, power card, backplane, and a mission unique interface card. The mechanical design for the box will also be detailed since it is critical in meeting the stringent thermal and structural requirements imposed by the processing system. In addition, the mechanical design uses advanced thermal conduction techniques to solve the internal thermal challenges.The SpaceCube v2.0 processing system is based on an extended version of the 3U cPCI standard form factor where each card is 190mm x 100mm in size The typical power draw of the processor card is 8 to 10W and scales with application complexity. The SpaceCube v2.0 data processing card features two Xilinx Virtex-5 QV Field Programmable Gate Arrays (FPGA), eight memory modules, a monitor FPGA with analog monitoring, Ethernet, configurable interconnect to the Xilinx FPGAs including gigabit transceivers, and the necessary voltage regulation. The processor board uses a back-to-back design methodology for common parts that maximizes the board real estate available. This paper will show how to meet the IPC 6012B Class 3A standard with a 22-layer board that has two column grid array devices with 1.0mm pitch. All layout trades such as stack-up options, via selection, and FPGA signal breakout will be discussed with feature size results. The overall board design process will be discussed including parts selection, circuit design, proper signal termination, layout placement and route planning, signal integrity design and verification, and power integrity results. The radiation mitigation techniques will also be detailed including configuration scrubbing options, Xilinx circuit mitigation and FPGA functional monitoring, and memory protection.Finally, this paper will describe how this system is being used to solve the extreme challenges of a robotic satellite servicing mission where typical space-rated processors are not sufficient enough to meet the intensive data processing requirements. The SpaceCube v2.0 is the main payload control computer and is required to control critical subsystems such as autonomous rendezvous and docking using a suite of vision sensors and object avoidance when controlling two robotic arms.

The Clue to Minimizing the Developer-User Divide by Good Practice in Earth and Space Science Informatics

NASA Astrophysics Data System (ADS)

Messerotti, M.

2009-04-01

Earth and Space Science research, as well as many other disciplines, can nowadays benefit from advanced data handling techniques and tools capable to significantly relieve the scientist of the burden of data search, retrieval, visualization and manipulation, and to exploit the data information content. Some typical examples are Virtual Observatories (VO) specific to a variety of sub-disciplines but anyway interlinked, a feature intrinsic to the VO architecture, Virtual Globes as advanced 3D selection and visualization interfaces to distributed data repositories, and the Global Earth Observation System of Systems. These information systems are proving also effective in education and outreach activities as they are usable via web interfaces to give access to, to display and to download nonhomogeneous datasets in order to raise the awareness of the students and the public on the relevant disciplines. Despite of that, all of this effective machineries are still poorly used both by the scientific community and by the community active in education and outreach. All such infrastructures are designed and developed according to the state-of-the-art information and computer engineering techniques and are provided with top features such as ontology- and semantics-based data management, and advanced unified web-based interfaces. Anyway, a careful analysis of the issue mentioned above indicates a key aspect that play a major role, i.e., the inadequate interaction with the users' communities during the design, the development, the deployment and the test phases. Even the best technical tool can appear inadequate to the final user when it does not meet the user's requirements in terms of achievable goals and use friendliness. In this work, we consider the user-side features to be taken into account for the optimum exploitation of an information system in the framework of the interaction among the design engineers and the target communities towards the setting of a good practice for minimizing the developer-user divide.

Divergence of Age-Related Differences in Social-Communication: Improvements for Typically Developing Youth but Declines for Youth with Autism Spectrum Disorder

ERIC Educational Resources Information Center

Wallace, Gregory L.; Dudley, Katerina; Anthony, Laura; Pugliese, Cara E.; Orionzi, Bako; Clasen, Liv; Lee, Nancy Raitano; Giedd, Jay N.; Martin, Alex; Raznahan, Armin; Kenworthy, Lauren

2017-01-01

Although social-communication difficulties and repetitive behaviors are hallmark features of autism spectrum disorder (ASD) and persist across the lifespan, very few studies have compared age-related differences in these behaviors between youth with ASD and same-age typically developing (TD) peers. We examined this issue using SRS-2 (Social…

Fortran programs for the time-dependent Gross-Pitaevskii equation in a fully anisotropic trap

NASA Astrophysics Data System (ADS)

Muruganandam, P.; Adhikari, S. K.

2009-10-01

Here we develop simple numerical algorithms for both stationary and non-stationary solutions of the time-dependent Gross-Pitaevskii (GP) equation describing the properties of Bose-Einstein condensates at ultra low temperatures. In particular, we consider algorithms involving real- and imaginary-time propagation based on a split-step Crank-Nicolson method. In a one-space-variable form of the GP equation we consider the one-dimensional, two-dimensional circularly-symmetric, and the three-dimensional spherically-symmetric harmonic-oscillator traps. In the two-space-variable form we consider the GP equation in two-dimensional anisotropic and three-dimensional axially-symmetric traps. The fully-anisotropic three-dimensional GP equation is also considered. Numerical results for the chemical potential and root-mean-square size of stationary states are reported using imaginary-time propagation programs for all the cases and compared with previously obtained results. Also presented are numerical results of non-stationary oscillation for different trap symmetries using real-time propagation programs. A set of convenient working codes developed in Fortran 77 are also provided for all these cases (twelve programs in all). In the case of two or three space variables, Fortran 90/95 versions provide some simplification over the Fortran 77 programs, and these programs are also included (six programs in all). Program summaryProgram title: (i) imagetime1d, (ii) imagetime2d, (iii) imagetime3d, (iv) imagetimecir, (v) imagetimesph, (vi) imagetimeaxial, (vii) realtime1d, (viii) realtime2d, (ix) realtime3d, (x) realtimecir, (xi) realtimesph, (xii) realtimeaxial Catalogue identifier: AEDU_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEDU_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 122 907 No. of bytes in distributed program, including test data, etc.: 609 662 Distribution format: tar.gz Programming language: FORTRAN 77 and Fortran 90/95 Computer: PC Operating system: Linux, Unix RAM: 1 GByte (i, iv, v), 2 GByte (ii, vi, vii, x, xi), 4 GByte (iii, viii, xii), 8 GByte (ix) Classification: 2.9, 4.3, 4.12 Nature of problem: These programs are designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in one-, two- or three-space dimensions with a harmonic, circularly-symmetric, spherically-symmetric, axially-symmetric or anisotropic trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Solution method: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation, in either imaginary or real time, over small time steps. The method yields the solution of stationary and/or non-stationary problems. Additional comments: This package consists of 12 programs, see "Program title", above. FORTRAN77 versions are provided for each of the 12 and, in addition, Fortran 90/95 versions are included for ii, iii, vi, viii, ix, xii. For the particular purpose of each program please see the below. Running time: Minutes on a medium PC (i, iv, v, vii, x, xi), a few hours on a medium PC (ii, vi, viii, xii), days on a medium PC (iii, ix). Program summary (1)Title of program: imagtime1d.F Title of electronic file: imagtime1d.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 1 GByte Programming language used: Fortran 77 Typical running time: Minutes on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in one-space dimension with a harmonic trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in imaginary time over small time steps. The method yields the solution of stationary problems. Program summary (2)Title of program: imagtimecir.F Title of electronic file: imagtimecir.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 1 GByte Programming language used: Fortran 77 Typical running time: Minutes on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in two-space dimensions with a circularly-symmetric trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in imaginary time over small time steps. The method yields the solution of stationary problems. Program summary (3)Title of program: imagtimesph.F Title of electronic file: imagtimesph.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 1 GByte Programming language used: Fortran 77 Typical running time: Minutes on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in three-space dimensions with a spherically-symmetric trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in imaginary time over small time steps. The method yields the solution of stationary problems. Program summary (4)Title of program: realtime1d.F Title of electronic file: realtime1d.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 2 GByte Programming language used: Fortran 77 Typical running time: Minutes on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in one-space dimension with a harmonic trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in real time over small time steps. The method yields the solution of stationary and non-stationary problems. Program summary (5)Title of program: realtimecir.F Title of electronic file: realtimecir.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 2 GByte Programming language used: Fortran 77 Typical running time: Minutes on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in two-space dimensions with a circularly-symmetric trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in real time over small time steps. The method yields the solution of stationary and non-stationary problems. Program summary (6)Title of program: realtimesph.F Title of electronic file: realtimesph.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 2 GByte Programming language used: Fortran 77 Typical running time: Minutes on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in three-space dimensions with a spherically-symmetric trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in real time over small time steps. The method yields the solution of stationary and non-stationary problems. Program summary (7)Title of programs: imagtimeaxial.F and imagtimeaxial.f90 Title of electronic file: imagtimeaxial.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 2 GByte Programming language used: Fortran 77 and Fortran 90 Typical running time: Few hours on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in three-space dimensions with an axially-symmetric trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in imaginary time over small time steps. The method yields the solution of stationary problems. Program summary (8)Title of program: imagtime2d.F and imagtime2d.f90 Title of electronic file: imagtime2d.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 2 GByte Programming language used: Fortran 77 and Fortran 90 Typical running time: Few hours on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in two-space dimensions with an anisotropic trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in imaginary time over small time steps. The method yields the solution of stationary problems. Program summary (9)Title of program: realtimeaxial.F and realtimeaxial.f90 Title of electronic file: realtimeaxial.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 4 GByte Programming language used: Fortran 77 and Fortran 90 Typical running time Hours on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in three-space dimensions with an axially-symmetric trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in real time over small time steps. The method yields the solution of stationary and non-stationary problems. Program summary (10)Title of program: realtime2d.F and realtime2d.f90 Title of electronic file: realtime2d.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 4 GByte Programming language used: Fortran 77 and Fortran 90 Typical running time: Hours on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in two-space dimensions with an anisotropic trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in real time over small time steps. The method yields the solution of stationary and non-stationary problems. Program summary (11)Title of program: imagtime3d.F and imagtime3d.f90 Title of electronic file: imagtime3d.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum RAM memory: 4 GByte Programming language used: Fortran 77 and Fortran 90 Typical running time: Few days on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in three-space dimensions with an anisotropic trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in imaginary time over small time steps. The method yields the solution of stationary problems. Program summary (12)Title of program: realtime3d.F and realtime3d.f90 Title of electronic file: realtime3d.tar.gz Catalogue identifier: Program summary URL: Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar.gz Computers: PC/Linux, workstation/UNIX Maximum Ram Memory: 8 GByte Programming language used: Fortran 77 and Fortran 90 Typical running time: Days on a medium PC Unusual features: None Nature of physical problem: This program is designed to solve the time-dependent Gross-Pitaevskii nonlinear partial differential equation in three-space dimensions with an anisotropic trap. The Gross-Pitaevskii equation describes the properties of a dilute trapped Bose-Einstein condensate. Method of solution: The time-dependent Gross-Pitaevskii equation is solved by the split-step Crank-Nicolson method by discretizing in space and time. The discretized equation is then solved by propagation in real time over small time steps. The method yields the solution of stationary and non-stationary problems.

Designing using manufacturing features

NASA Astrophysics Data System (ADS)

Szecsi, T.; Hoque, A. S. M.

2012-04-01

This paper presents a design system that enables the composition of a part using manufacturing features. Features are selected from feature libraries. Upon insertion, the system ensures that the feature does not contradict the design-for-manufacture rules. This helps eliminating costly manufacturing problems. The system is developed as an extension to a commercial CAD/CAM system Pro/Engineer.

Engaging Students in a Large-Enrollment Physics Class Using an Academically Focused Social Media Platform

NASA Astrophysics Data System (ADS)

Gavrin, Andy; Lindell, Rebecca

2017-03-01

There are many reasons for an instructor to consider using social media, particularly in a large introductory course. Improved communications can lessen the sense of isolation some students feel in large classes, and students may be more likely to respond to faculty announce-ments in a form that is familiar and comfortable. Furthermore, many students currently establish social media sites for their classes, without the knowledge or participation of their instructors. Such "shadow" sites can be useful, but they can also become distributors of misinformation, or venues for inappropriate or disruptive discussions. CourseNetworking (CN) is a social media platform designed for the academic environment. It combines many features common among learning management systems (LMS's) with an interface that looks and feels more like Facebook than a typical academic system. We have recently begun using CN as a means to engage students in an introductory calculus-based mechanics class, with enrollments of 150-200 students per semester. This article presents basic features of CN, and details our initial experiences and observations.

Designing a stochastic genetic switch by coupling chaos and bistability.

PubMed

Zhao, Xiang; Ouyang, Qi; Wang, Hongli

2015-11-01

In stem cell differentiation, a pluripotent stem cell becomes progressively specialized and generates specific cell types through a series of epigenetic processes. How cells can precisely determine their fate in a fluctuating environment is a currently unsolved problem. In this paper, we suggest an abstract gene regulatory network to describe mathematically the differentiation phenomenon featuring stochasticity, divergent cell fates, and robustness. The network consists of three functional motifs: an upstream chaotic motif, a buffering motif of incoherent feed forward loop capable of generating a pulse, and a downstream motif which is bistable. The dynamic behavior is typically a transient chaos with fractal basin boundaries. The trajectories take transiently chaotic journeys before divergently settling down to the bistable states. The ratio of the probability that the high state is achieved to the probability that the low state is reached can maintain a constant in a population of cells with varied molecular fluctuations. The ratio can be turned up or down when proper parameters are adjusted. The model suggests a possible mechanism for the robustness against fluctuations that is prominently featured in pluripotent cell differentiations and developmental phenomena.

Free-jet acoustic investigation of high-radius-ratio coannular plug nozzles

NASA Technical Reports Server (NTRS)

Knott, P. R.; Janardan, B. A.; Majjigi, R. K.; Bhutiani, P. K.; Vogt, P. G.

1984-01-01

The experimental and analytical results of a scale model simulated flight acoustic exploratory investigation of high radius ratio coannular plug nozzles with inverted velocity and temperature profiles are summarized. Six coannular plug nozzle configurations and a baseline convergent conical nozzle were tested for simulated flight acoustic evaluation. The nozzles were tested over a range of test conditions that are typical of a Variable Cycle Engine for application to advanced high speed aircraft. It was found that in simulate flight, the high radius ratio coannular plug nozzles maintain their jet noise and shock noise reduction features previously observed in static testing. The presence of nozzle bypass struts will not significantly affect the acousticn noise reduction features of a General Electric type nozzle design. A unique coannular plug nozzle flight acoustic spectral prediction method was identified and found to predict the measured results quite well. Special laser velocimeter and acoustic measurements were performed which have given new insights into the jet and shock noise reduction mechanisms of coannular plug nozzles with regard to identifying further benificial research efforts.

A beginner's guide to atomic force microscopy probing for cell mechanics

PubMed Central

2016-01-01

Abstract Atomic Force microscopy (AFM) is becoming a prevalent tool in cell biology and biomedical studies, especially those focusing on the mechanical properties of cells and tissues. The newest generation of bio‐AFMs combine ease of use and seamless integration with live‐cell epifluorescence or more advanced optical microscopies. As a unique feature with respect to other bionanotools, AFM provides nanometer‐resolution maps for cell topography, stiffness, viscoelasticity, and adhesion, often overlaid with matching optical images of the probed cells. This review is intended for those about to embark in the use of bio‐AFMs, and aims to assist them in designing an experiment to measure the mechanical properties of adherent cells. In addition to describing the main steps in a typical cell mechanics protocol and explaining how data is analysed, this review will also discuss some of the relevant contact mechanics models available and how they have been used to characterize specific features of cellular and biological samples. Microsc. Res. Tech. 80:75–84, 2017. © 2016 Wiley Periodicals, Inc. PMID:27676584

Analysis and design of asymmetrical reluctance machine

NASA Astrophysics Data System (ADS)

Harianto, Cahya A.

Over the past few decades the induction machine has been chosen for many applications due to its structural simplicity and low manufacturing cost. However, modest torque density and control challenges have motivated researchers to find alternative machines. The permanent magnet synchronous machine has been viewed as one of the alternatives because it features higher torque density for a given loss than the induction machine. However, the assembly and permanent magnet material cost, along with safety under fault conditions, have been concerns for this class of machine. An alternative machine type, namely the asymmetrical reluctance machine, is proposed in this work. Since the proposed machine is of the reluctance machine type, it possesses desirable feature, such as near absence of rotor losses, low assembly cost, low no-load rotational losses, modest torque ripple, and rather benign fault conditions. Through theoretical analysis performed herein, it is shown that this machine has a higher torque density for a given loss than typical reluctance machines, although not as high as the permanent magnet machines. Thus, the asymmetrical reluctance machine is a viable and advantageous machine alternative where the use of permanent magnet machines are undesirable.

Parallel Key Frame Extraction for Surveillance Video Service in a Smart City.

PubMed

Zheng, Ran; Yao, Chuanwei; Jin, Hai; Zhu, Lei; Zhang, Qin; Deng, Wei

2015-01-01

Surveillance video service (SVS) is one of the most important services provided in a smart city. It is very important for the utilization of SVS to provide design efficient surveillance video analysis techniques. Key frame extraction is a simple yet effective technique to achieve this goal. In surveillance video applications, key frames are typically used to summarize important video content. It is very important and essential to extract key frames accurately and efficiently. A novel approach is proposed to extract key frames from traffic surveillance videos based on GPU (graphics processing units) to ensure high efficiency and accuracy. For the determination of key frames, motion is a more salient feature in presenting actions or events, especially in surveillance videos. The motion feature is extracted in GPU to reduce running time. It is also smoothed to reduce noise, and the frames with local maxima of motion information are selected as the final key frames. The experimental results show that this approach can extract key frames more accurately and efficiently compared with several other methods.

Multifunctional mesoporous silica nanoparticles for combined therapeutic, diagnostic and targeted action in cancer treatment.

PubMed

Rosenholm, Jessica M; Sahlgren, Cecilia; Lindén, Mika

2011-07-01

The main objective in the development of nanomedicine is to obtain delivery platforms for targeted delivery of drugs or imaging agents for improved therapeutic efficacy, reduced side effects and increased diagnostic sensitivity. A (nano)material class that has been recognized for its controllable properties on many levels is ordered mesoporous inorganic materials, typically in the form of amorphous silica (SiO2). Characteristics for this class of materials include mesoscopic order, tunable pore dimensions in the (macro)molecular size range, a high pore volume and surface area, the possibility for selective surface functionality as well as morphology control. The robust but biodegradable ceramic matrix moreover provides shelter for incorporated agents (drugs, proteins, imaging agents, photosensitizers) leaving the outer particle surface free for further modification. The unique features make these materials particularly amenable to modular design, whereby functional moieties and features may be interchanged or combined to produce multifunctional nanodelivery systems combining targeting, diagnostic, and therapeutic actions. This review covers the latest developments related to the use of mesoporous silica nanoparticles (MSNs) as nanocarriers in biomedical applications, with special focus on cancer therapy and diagnostics.

Picosecond imaging of inertial confinement fusion plasmas using electron pulse-dilation

NASA Astrophysics Data System (ADS)

Hilsabeck, T. J.; Nagel, S. R.; Hares, J. D.; Kilkenny, J. D.; Bell, P. M.; Bradley, D. K.; Dymoke-Bradshaw, A. K. L.; Piston, K.; Chung, T. M.

2017-02-01

Laser driven inertial confinement fusion (ICF) plasmas typically have burn durations on the order of 100 ps. Time resolved imaging of the x-ray self emission during the hot spot formation is an important diagnostic tool which gives information on implosion symmetry, transient features and stagnation time. Traditional x-ray gated imagers for ICF use microchannel plate detectors to obtain gate widths of 40-100 ps. The development of electron pulse-dilation imaging has enabled a 10X improvement in temporal resolution over legacy instruments. In this technique, the incoming x-ray image is converted to electrons at a photocathode. The electrons are accelerated with a time-varying potential that leads to temporal expansion as the electron signal transits the tube. This expanded signal is recorded with a gated detector and the effective temporal resolution of the composite system can be as low as several picoseconds. An instrument based on this principle, known as the Dilation X-ray Imager (DIXI) has been constructed and fielded at the National Ignition Facility. Design features and experimental results from DIXI will be presented.

A model of face selection in viewing video stories

PubMed Central

Suda, Yuki; Kitazawa, Shigeru

2015-01-01

When typical adults watch TV programs, they show surprisingly stereo-typed gaze behaviours, as indicated by the almost simultaneous shifts of their gazes from one face to another. However, a standard saliency model based on low-level physical features alone failed to explain such typical gaze behaviours. To find rules that explain the typical gaze behaviours, we examined temporo-spatial gaze patterns in adults while they viewed video clips with human characters that were played with or without sound, and in the forward or reverse direction. We here show the following: 1) the “peak” face scanpath, which followed the face that attracted the largest number of views but ignored other objects in the scene, still retained the key features of actual scanpaths, 2) gaze behaviours remained unchanged whether the sound was provided or not, 3) the gaze behaviours were sensitive to time reversal, and 4) nearly 60% of the variance of gaze behaviours was explained by the face saliency that was defined as a function of its size, novelty, head movements, and mouth movements. These results suggest that humans share a face-oriented network that integrates several visual features of multiple faces, and directs our eyes to the most salient face at each moment. PMID:25597621

Chemical and structural indicators for large redox potentials in Fe-based positive electrode materials.

PubMed

Melot, Brent C; Scanlon, David O; Reynaud, Marine; Rousse, Gwenaëlle; Chotard, Jean-Noël; Henry, Marc; Tarascon, Jean-Marie

2014-07-23

Li-ion batteries have enabled a revolution in the way portable consumer-electronics are powered and will play an important role as large-scale electrochemical storage applications like electric vehicles and grid-storage are developed. The ability to identify and design promising new positive insertion electrodes will be vital in continuing to push Li-ion technology to its fullest potential. Utilizing a combination of computational tools and structural analysis, we report new indicators which will facilitate the recognition of phases with the desired redox potential. Most importantly of these, we find there is a strong correlation between the presence of Li ions sitting in close-proximity to the redox center of polyanionic phases and the open circuit voltage in Fe-based cathodes. This common structural feature suggests that the bonding associated with Li may have a secondary inductive effect which increases the ionic character of Fe bonds beyond what is typically expected based purely on arguments of electronegativity associated with the polyanionic group. This correlation is supported by ab initio calculations which show the Bader charge increases (reflecting an increased ionicity) in a nearly linear fashion with the experimental cell potentials. These features are demonstrated to be consistent across a wide variety of compositions and structures and should help to facilitate the design of new, high-potential, and environmentally sustainable insertion electrodes.

The design and fabrication of a prototype trash compacting unit. [for long duration space missions

NASA Technical Reports Server (NTRS)

1973-01-01

A prototype trash compactor, that is compatible with the anticipated requirements of future long-term space missions, is described. Preliminary problem definition studies were conducted to identify typical types and quantities of waste materials to be expected from a typical mission. Bench-scale compaction tests were then conducted on typical waste materials to determine force/compaction curves. These data were used to design a boilerplate compactor that was fabricated to prove the feasibility of the basic design concept. A final design was then prepared from which the deliverable unit was fabricated. Design concepts are presented for suggested further development of the compactor, including a version that is capable of handling wet biodegradable wastes.

2-SR-based electrically small antenna for RFID applications

NASA Astrophysics Data System (ADS)

Paredes, Ferran; Zuffanelli, Simone; Aguilà, Pau; Zamora, Gerard; Martin, Ferran; Bonache, Jordi

2016-04-01

In this work, the 2-turn spiral resonator (2-SR) is proposed as an electrically small antenna for passive radio frequency identification (RFID) tags at the European ultra-high frequency (UHF) band. The radiation properties are studied in order to explore the viability of the 2-SR applied to tag antenna design. Based on analytical calculations, the radiation pattern is found to provide a cancelation of the radiation nulls. This results in a mitigation of the blind spots in the read range, which are present in typical UHF-RFID tags as an undesired feature. As a proof of concept, a passive tag of size 35 mm × 40 mm (λ 0/10 × λ 0/9) based on the 2-SR antenna is designed and fabricated. Good radiation efficiency (75 %) and a quasi-isotropic radiation pattern are obtained. The experimental tag read range for different directions is in good agreement with the simulation results. The measured read range exhibits maximum and minimum values of 6.7 and 3.5 m, respectively.

Low-Cost, Portable, Multi-Wall Virtual Reality

NASA Technical Reports Server (NTRS)

Miller, Samuel A.; Misch, Noah J.; Dalton, Aaron J.

2005-01-01

Virtual reality systems make compelling outreach displays, but some such systems, like the CAVE, have design features that make their use for that purpose inconvenient. In the case of the CAVE, the equipment is difficult to disassemble, transport, and reassemble, and typically CAVEs can only be afforded by large-budget research facilities. We implemented a system like the CAVE that costs less than $30,000, weighs about 500 pounds, and fits into a fifteen-passenger van. A team of six people have unpacked, assembled, and calibrated the system in less than two hours. This cost reduction versus similar virtual-reality systems stems from the unique approach we took to stereoscopic projection. We used an assembly of optical chopper wheels and commodity LCD projectors to create true active stereo at less than a fifth of the cost of comparable active-stereo technologies. The screen and frame design also optimized portability; the frame assembles in minutes with only two fasteners, and both it and the screen pack into small bundles for easy and secure shipment.

RCTS: A flexible environment for sensor integration and control of robot systems; the distributed processing approach

NASA Technical Reports Server (NTRS)

Allard, R.; Mack, B.; Bayoumi, M. M.

1989-01-01

Most robot systems lack a suitable hardware and software environment for the efficient research of new control and sensing schemes. Typically, engineers and researchers need to be experts in control, sensing, programming, communication and robotics in order to implement, integrate and test new ideas in a robot system. In order to reduce this time, the Robot Controller Test Station (RCTS) has been developed. It uses a modular hardware and software architecture allowing easy physical and functional reconfiguration of a robot. This is accomplished by emphasizing four major design goals: flexibility, portability, ease of use, and ease of modification. An enhanced distributed processing version of RCTS is described. It features an expanded and more flexible communication system design. Distributed processing results in the availability of more local computing power and retains the low cost of microprocessors. A large number of possible communication, control and sensing schemes can therefore be easily introduced and tested, using the same basic software structure.

DEIVA: a web application for interactive visual analysis of differential gene expression profiles.

PubMed

Harshbarger, Jayson; Kratz, Anton; Carninci, Piero

2017-01-07

Differential gene expression (DGE) analysis is a technique to identify statistically significant differences in RNA abundance for genes or arbitrary features between different biological states. The result of a DGE test is typically further analyzed using statistical software, spreadsheets or custom ad hoc algorithms. We identified a need for a web-based system to share DGE statistical test results, and locate and identify genes in DGE statistical test results with a very low barrier of entry. We have developed DEIVA, a free and open source, browser-based single page application (SPA) with a strong emphasis on being user friendly that enables locating and identifying single or multiple genes in an immediate, interactive, and intuitive manner. By design, DEIVA scales with very large numbers of users and datasets. Compared to existing software, DEIVA offers a unique combination of design decisions that enable inspection and analysis of DGE statistical test results with an emphasis on ease of use.

Evidence for Itinerant Carriers in an Anisotropic Narrow-Gap Semiconductor by Angle-Resolved Photoemission Spectroscopy.

PubMed

Ju, Sailong; Bai, Wei; Wu, Liming; Lin, Hua; Xiao, Chong; Cui, Shengtao; Li, Zhou; Kong, Shuai; Liu, Yi; Liu, Dayong; Zhang, Guobin; Sun, Zhe; Xie, Yi

2018-01-01

The ability to accurately determine the electronic structure of solids has become a key prerequisite for modern functional materials. For example, the precise determination of the electronic structure helps to balance the three thermoelectric parameters, which is the biggest challenge to design high-performance thermoelectric materials. Herein, by high-resolution, angle-resolved photoemission spectroscopy (ARPES), the itinerant carriers in CsBi 4 Te 6 (CBT) are revealed for the first time. CBT is a typical anisotropic, narrow-gap semiconductor used as a practical candidate for low-temperature thermoelectric applications, and p-doped CBT series show superconductivity at relatively low carrier concentrations. The ARPES results show a significantly larger bandwidth near the Fermi surface than calculations, which means the carriers transport anisotropically and itinerantly in CBT. It is reasonable to believe that these newly discovered features of carriers in narrow-gap semiconductors are promising for designing optimal thermoelectric materials and superconductors. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Introduction and Highlights of the Workshop

NASA Technical Reports Server (NTRS)

Noor, Ahmed K.; Venneri, Samuel L.

1997-01-01

Four generations of CAD/CAM systems can be identified, corresponding to changes in both modeling functionality and software architecture. The systems evolved from 2D and wireframes to solid modeling, to parametric/variational modelers to the current simulation-embedded systems. Recent developments have enabled design engineers to perform many of the complex analysis tasks, typically performed by analysis experts. Some of the characteristics of the current and emerging CAD/CAM/CAE systems are described in subsequent presentations. The focus of the workshop is on the potential of CAD/CAM/CAE systems for use in simulating the entire mission and life-cycle of future aerospace systems, and the needed development to realize this potential. First, the major features of the emerging computing, communication and networking environment are outlined; second, the characteristics and design drivers of future aerospace systems are identified; third, the concept of intelligent synthesis environment being planned by NASA, the UVA ACT Center and JPL is presented; and fourth, the objectives and format of the workshop are outlined.

Orbit design and optimization based on global telecommunication performance metrics

NASA Technical Reports Server (NTRS)

Lee, Seungwon; Lee, Charles H.; Kerridge, Stuart; Cheung, Kar-Ming; Edwards, Charles D.

2006-01-01

The orbit selection of telecommunications orbiters is one of the critical design processes and should be guided by global telecom performance metrics and mission-specific constraints. In order to aid the orbit selection, we have coupled the Telecom Orbit Analysis and Simulation Tool (TOAST) with genetic optimization algorithms. As a demonstration, we have applied the developed tool to select an optimal orbit for general Mars telecommunications orbiters with the constraint of being a frozen orbit. While a typical optimization goal is to minimize tele-communications down time, several relevant performance metrics are examined: 1) area-weighted average gap time, 2) global maximum of local maximum gap time, 3) global maximum of local minimum gap time. Optimal solutions are found with each of the metrics. Common and different features among the optimal solutions as well as the advantage and disadvantage of each metric are presented. The optimal solutions are compared with several candidate orbits that were considered during the development of Mars Telecommunications Orbiter.

Nanocomposites Based on Thermoplastic Polymers and Functional Nanofiller for Sensor Applications

PubMed Central

Coiai, Serena; Passaglia, Elisa; Pucci, Andrea; Ruggeri, Giacomo

2015-01-01

Thermoplastic polymers like polyolefins, polyesters, polyamide, and styrene polymers are the most representative commodity plastics thanks to their cost-efficient manufacturing processes, excellent thermomechanical properties and their good environmental compatibility, including easy recycling. In the last few decades much effort has been devoted worldwide to extend the applications of such materials by conferring on them new properties through mixing and blending with different additives. In this latter context, nanocomposites have recently offered new exciting possibilities. This review discusses the successful use of nanostructured dispersed substrates in designing new stimuli-responsive nanocomposites; in particular, it provides an updated description of the synthetic routes to prepare nanostructured systems having the typical properties of thermoplastic polymers (continuous matrix), but showing enhanced optical, conductive, and thermal features dependent on the dispersion topology. The controlled nanodispersion of functional labeled clays, noble metal nanoparticles and carbon nanotubes is here evidenced to play a key role in producing hybrid thermoplastic materials that have been used in the design of devices, such as NLO devices, chemiresistors, temperature and deformation sensors.

Investigation on a mechanical vibration absorber with tunable piecewise-linear stiffness

NASA Astrophysics Data System (ADS)

Shui, Xin; Wang, Shimin

2018-02-01

The design and characterization of a mechanical vibration absorber are addressed. A distinctive feature of the absorber is its tunable piecewise-linear stiffness, which is realized by means of a slider with two stop-blocks installed constraining the bilateral deflections of the elastic support. A new analytical approach named as the equivalent stiffness technique (EST) is introduced and then employed to obtain the analytical relations of the frequency, amplitude and phase with a view to exhibit a more comprehensive characterization of the absorber. Experiments are conducted to demonstrate the feasibility of the design. The experimental data show good agreement with the analytical results. The final results indicate that the tunable stiffness absorber (TSA) possesses a typical nonlinear characteristic at each given position of the slider, and its stiffness can be tuned in real time over a wide range by adjusting the slider position. Hence the TSA has a large optimum vibration-absorption range together with a wide suppression band around each optimal position, which contributes to its excellent capacity of vibration absorption.

Distributed Group Design Process: Lessons Learned.

ERIC Educational Resources Information Center

Eseryel, Deniz; Ganesan, Radha

A typical Web-based training development team consists of a project manager, an instructional designer, a subject-matter expert, a graphic artist, and a Web programmer. The typical scenario involves team members working together in the same setting during the entire design and development process. What happens when the team is distributed, that is…

FPGA-based design and implementation of arterial pulse wave generator using piecewise Gaussian-cosine fitting.

PubMed

Wang, Lu; Xu, Lisheng; Zhao, Dazhe; Yao, Yang; Song, Dan

2015-04-01

Because arterial pulse waves contain vital information related to the condition of the cardiovascular system, considerable attention has been devoted to the study of pulse waves in recent years. Accurate acquisition is essential to investigate arterial pulse waves. However, at the stage of developing equipment for acquiring and analyzing arterial pulse waves, specific pulse signals may be unavailable for debugging and evaluating the system under development. To produce test signals that reflect specific physiological conditions, in this paper, an arterial pulse wave generator has been designed and implemented using a field programmable gate array (FPGA), which can produce the desired pulse waves according to the feature points set by users. To reconstruct a periodic pulse wave from the given feature points, a method known as piecewise Gaussian-cosine fitting is also proposed in this paper. Using a test database that contains four types of typical pulse waves with each type containing 25 pulse wave signals, the maximum residual error of each sampling point of the fitted pulse wave in comparison with the real pulse wave is within 8%. In addition, the function for adding baseline drift and three types of noises is integrated into the developed system because the baseline occasionally wanders, and noise needs to be added for testing the performance of the designed circuits and the analysis algorithms. The proposed arterial pulse wave generator can be considered as a special signal generator with a simple structure, low cost and compact size, which can also provide flexible solutions for many other related research purposes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Process Sensitivity, Performance, and Direct Verification Testing of Adhesive Locking Features

NASA Technical Reports Server (NTRS)

Golden, Johnny L.; Leatherwood, Michael D.; Montoya, Michael D.; Kato, Ken A.; Akers, Ed

2012-01-01

Phase I: The use of adhesive locking features or liquid locking compounds (LLCs) (e.g., Loctite) as a means of providing a secondary locking feature has been used on NASA programs since the Apollo program. In many cases Loctite was used as a last resort when (a) self-locking fasteners were no longer functioning per their respective drawing specification, (b) access was limited for removal & replacement, or (c) replacement could not be accomplished without severe impact to schedule. Long-term use of Loctite became inevitable in cases where removal and replacement of worn hardware was not cost effective and Loctite was assumed to be fully cured and working. The NASA Engineering & Safety Center (NESC) and United Space Alliance (USA) recognized the need for more extensive testing of Loctite grades to better understand their capabilities and limitations as a secondary locking feature. These tests, identified as Phase I, were designed to identify processing sensitivities, to determine proper cure time, the correct primer to use on aerospace nutplate, insert and bolt materials such as A286 and MP35N, and the minimum amount of Loctite that is required to achieve optimum breakaway torque values. The .1900-32 was the fastener size tested, due to wide usage in the aerospace industry. Three different grades of Loctite were tested. Results indicate that, with proper controls, adhesive locking features can be successfully used in the repair of locking features and should be considered for design. Phase II: Threaded fastening systems used in aerospace programs typically have a requirement for a redundant locking feature. The primary locking method is the fastener preload and the traditional redundant locking feature is a self-locking mechanical device that may include deformed threads, non-metallic inserts, split beam features, or other methods that impede movement between threaded members. The self-locking resistance of traditional locking features can be directly verified during assembly by measuring the dynamic prevailing torque. Adhesive locking features or LLCs are another method of providing redundant locking, but a direct verification method has not been used in aerospace applications to verify proper installation when using LLCs because of concern for damage to the adhesive bond. The reliability of LLCs has also been questioned due to failures observed during testing with coupons for process verification, although the coupon failures have often been attributed to a lack of proper procedures. It is highly desirable to have a direct method of verifying the LLC cure or bond integrity. The purpose of the Phase II test program was to determine if the torque applied during direct verification of an adhesive locking feature degrades that locking feature. This report documents the test program used to investigate the viability of such a direct verification method. Results of the Phase II testing were positive, and additional investigation of direct verification of adhesive locking features is merited.

[Fanconi Anemia, Complementation Group D1 Caused by Biallelic Mutations of BRCA2 Gene--Case Report].

PubMed

Puchmajerová, A; Švojgr, K; Novotná, D; Macháčková, E; Sumerauer, D; Smíšek, P; Kodet, R; Kynčl, M; Křepelová, A; Foretová, L

2016-01-01

Fanconi anemia is a rare autosomal recessive disorder, clinically and genetically heterogeneous, characterized by typical clinical features, such as short stature, microcephaly, skeletal abnormalities, abnormal skin pigmentations, developmental delay and congenital heart, kidney anomalies etc. Pancytopenia leading to bone marrow failure occurs in the first decade. Patients with Fanconi anemia have a high risk of hematologic malignancies and solid tumors. The diagnosis of Fanconi anemia is based on cytogenetic testing for increased rates of spontaneous chromosomal breakage and increased sensitivity to diepoxybutane or mitomycin C. Fanconi anemia is a heterogeneous disorder, at least 15 complementation groups are described, and 15 genes in which mutations are responsible for all of the 15 Fanconi anemia complementation groups have been identified. Unlike other Fanconi anemia complementation groups, for complementation group D1 (FANCD1), the bone marrow failure is not a typical feature, but early-onset leukemia and specific solid tumors, most often medulloblastoma and Wilms tumor, are typical for this complementation group.

Classification of Clinical Research Study Eligibility Criteria to Support Multi-Stage Cohort Identification Using Clinical Data Repositories.

PubMed

Cimino, James J; Lancaster, William J; Wyatt, Mathew C

2017-01-01

One of the challenges to using electronic health record (EHR) repositories for research is the difficulty mapping study subject eligibility criteria to the query capabilities of the repository. We sought to characterize criteria as "easy" (searchable in a typical repository), "hard" (requiring manual review of the record data), and "impossible" (not typically available in EHR repositories). We obtained 292 criteria from 20 studies available from Clinical Trials.gov and rated them according to our three types, plus a fourth "mixed" type. We had good agreement among three independent reviewers and chose 274 criteria that were characterized by single types for further analysis. The resulting analysis showed typical features of criteria that do and don't map to repositories. We propose that these features be used to guide researchers in specifying eligibility criteria to improve development of enrollment workflow, including the definition of EHR repository queries for self-service or analyst-mediated retrievals.

The Face of Noonan Syndrome: Does Phenotype Predict Genotype

PubMed Central

Allanson, Judith E.; Bohring, Axel; Dorr, Helmuth-Guenther; Dufke, Andreas; Gillessen-Kaesbach, Gabrielle; Horn, Denise; König, Rainer; Kratz, Christian P.; Kutsche, Kerstin; Pauli, Silke; Raskin, Salmo; Rauch, Anita; Turner, Anne; Wieczorek, Dagmar; Zenker, Martin

2011-01-01

The facial photographs of 81 individuals with Noonan syndrome, from infancy to adulthood, have been evaluated by two dysmorphologists (JA and MZ), each of whom has considerable experience with disorders of the Ras/MAPK pathway. Thirty-two of this cohort have PTPN11 mutations, 21 SOS1 mutations, 11 RAF1 mutations, and 17 KRAS mutations. The facial appearance of each person was judged to be typical of Noonan syndrome or atypical. In each gene category both typical and unusual faces were found. We determined that some individuals with mutations in the most commonly affected gene, PTPN11, which is correlated with the cardinal physical features, may have a quite atypical face. Conversely, some individuals with KRAS mutations, which may be associated with a less characteristic intellectual phenotype and a resemblance to Costello and cardio-facio-cutaneous syndromes, can have a very typical face. Thus, the facial phenotype, alone, is insufficient to predict the genotype, but certain facial features may facilitate an educated guess in some cases. PMID:20602484

Use of Natural and Nature-Based Features (NNBF) for Coastal Resilience

DTIC Science & Technology

2015-01-01

Factors contributing to weathering and erosion of bluffs and low banks , exemplary of features found in Chesapeake and Delaware Bays. Some bluffs may be...of low banks and bluffs (typically less than 10 meters (m) high), marshes, short sand spits, beaches fronting the mainland (without ponds or marshes...and erosion of bluffs and low banks , exemplary of features found in Chesapeake and Delaware Bays. Some bluffs may be fronted with narrow sand beaches

Geomorphology, tectonics, and exploration

NASA Technical Reports Server (NTRS)

Sabins, F. F., Jr.

1985-01-01

Explorationists interpret satellite images for tectonic features and patterns that may be clues to mineral and energy deposits. The tectonic features of interest range in scale from regional (sedimentary basins, fold belts) to local (faults, fractures) and are generally expressed as geomorphic features in remote sensing images. Explorationists typically employ classic concepts of geomorphology and landform analysis for their interpretations, which leads to the question - Are there new and evolving concepts in geomorphology that may be applicable to tectonic analyses of images?

Kinematic Measurements of the Vocal-Fold Displacement Waveform in Typical Children and Adult Populations: Quantification of High-Speed Endoscopic Videos

PubMed Central

Donohue, Kevin D.; Unnikrishnan, Harikrishnan; Kryscio, Richard J.

2015-01-01

Purpose This article presents a quantitative method for assessing instantaneous and average lateral vocal-fold motion from high-speed digital imaging, with a focus on developmental changes in vocal-fold kinematics during childhood. Method Vocal-fold vibrations were analyzed for 28 children (aged 5–11 years) and 28 adults (aged 21–45 years) without voice disorders. The following kinematic features were analyzed from the vocal-fold displacement waveforms: relative velocity-based features (normalized average and peak opening and closing velocities), relative acceleration-based features (normalized peak opening and closing accelerations), speed quotient, and normalized peak displacement. Results Children exhibited significantly larger normalized peak displacements, normalized average and peak opening velocities, normalized average and peak closing velocities, peak opening and closing accelerations, and speed quotient compared to adult women. Values of normalized average closing velocity and speed quotient were higher in children compared to adult men. Conclusions When compared to adult men, developing children typically have higher estimates of kinematic features related to normalized displacement and its derivatives. In most cases, the kinematic features of children are closer to those of adult men than adult women. Even though boys experience greater changes in glottal length and pitch as they mature, results indicate that girls experience greater changes in kinematic features compared to boys. PMID:25652615

A clinically viable capsule endoscopy video analysis platform for automatic bleeding detection

NASA Astrophysics Data System (ADS)

Yi, Steven; Jiao, Heng; Xie, Jean; Mui, Peter; Leighton, Jonathan A.; Pasha, Shabana; Rentz, Lauri; Abedi, Mahmood

2013-02-01

In this paper, we present a novel and clinically valuable software platform for automatic bleeding detection on gastrointestinal (GI) tract from Capsule Endoscopy (CE) videos. Typical CE videos for GI tract run about 8 hours and are manually reviewed by physicians to locate diseases such as bleedings and polyps. As a result, the process is time consuming and is prone to disease miss-finding. While researchers have made efforts to automate this process, however, no clinically acceptable software is available on the marketplace today. Working with our collaborators, we have developed a clinically viable software platform called GISentinel for fully automated GI tract bleeding detection and classification. Major functional modules of the SW include: the innovative graph based NCut segmentation algorithm, the unique feature selection and validation method (e.g. illumination invariant features, color independent features, and symmetrical texture features), and the cascade SVM classification for handling various GI tract scenes (e.g. normal tissue, food particles, bubbles, fluid, and specular reflection). Initial evaluation results on the SW have shown zero bleeding instance miss-finding rate and 4.03% false alarm rate. This work is part of our innovative 2D/3D based GI tract disease detection software platform. While the overall SW framework is designed for intelligent finding and classification of major GI tract diseases such as bleeding, ulcer, and polyp from the CE videos, this paper will focus on the automatic bleeding detection functional module.

Indian Private Higher Education in Comparative Perspective. PROPHE Working Paper Series. WP No. 13

ERIC Educational Resources Information Center

Levy, Daniel C.

2008-01-01

India demonstrates many features characteristic of private higher education in much of the world. Among these features are proportional size, with roughly 30 percent of total enrollment, and fast growth. Also rather typical is finance, which comes almost exclusively from non-government sources, principally tuition, while public higher education is…

Extremely Selective Attention: Eye-Tracking Studies of the Dynamic Allocation of Attention to Stimulus Features in Categorization

ERIC Educational Resources Information Center

Blair, Mark R.; Watson, Marcus R.; Walshe, R. Calen; Maj, Fillip

2009-01-01

Humans have an extremely flexible ability to categorize regularities in their environment, in part because of attentional systems that allow them to focus on important perceptual information. In formal theories of categorization, attention is typically modeled with weights that selectively bias the processing of stimulus features. These theories…

Fabrication of two-dimensional visible wavelength nanoscale plasmonic structures using hydrogen silsesquioxane based resist

NASA Astrophysics Data System (ADS)

Smith, Kyle Z.; Gadde, Akshitha; Kadiyala, Anand; Dawson, Jeremy M.

2016-03-01

In recent years, the global market for biosensors has continued to increase in combination with their expanding use in areas such as biodefense/detection, home diagnostics, biometric identification, etc. A constant necessity for inexpensive, portable bio-sensing methods, while still remaining simple to understand and operate, is the motivation behind novel concepts and designs. Labeled visible spectrum bio-sensing systems provide instant feedback that is both simple and easy to work with, but are limited by the light intensity thresholds required by the imaging systems. In comparison, label-free bio-sensing systems and other detection modalities like electrochemical, frequency resonance, thermal change, etc., can require additional technical processing steps to convey the final result, increasing the system's complexity and possibly the time required for analysis. Further decrease in the detection limit can be achieved through the addition of plasmonic structures into labeled bio-sensing systems. Nano-structures that operate in the visible spectrum have feature sizes typically in the order of the operating wavelength, calling for high aspect ratio nanoscale fabrication capabilities. In order to achieve these dimensions, electron beam lithography (EBL) is used due to its accurate feature production. Hydrogen silsesquioxane (HSQ) based electron beam resist is chosen for one of its benefits, which is after exposure to oxygen plasma, the patterned resist cures into silicon dioxide (SiO2). These cured features in conjunction with nanoscale gold particles help in producing a high electric field through dipole generation. In this work, a detailed process flow of the fabrication of square lattice of plasmonic structures comprising of gold coated silicon dioxide pillars designed to operate at 560 nm wavelength and produce an intensity increase of roughly 100 percent will be presented.

No Effect of Featural Attention on Body Size Aftereffects

PubMed Central

Stephen, Ian D.; Bickersteth, Chloe; Mond, Jonathan; Stevenson, Richard J.; Brooks, Kevin R.

2016-01-01

Prolonged exposure to images of narrow bodies has been shown to induce a perceptual aftereffect, such that observers’ point of subjective normality (PSN) for bodies shifts toward narrower bodies. The converse effect is shown for adaptation to wide bodies. In low-level stimuli, object attention (attention directed to the object) and spatial attention (attention directed to the location of the object) have been shown to increase the magnitude of visual aftereffects, while object-based attention enhances the adaptation effect in faces. It is not known whether featural attention (attention directed to a specific aspect of the object) affects the magnitude of adaptation effects in body stimuli. Here, we manipulate the attention of Caucasian observers to different featural information in body images, by asking them to rate the fatness or sex typicality of male and female bodies manipulated to appear fatter or thinner than average. PSNs for body fatness were taken at baseline and after adaptation, and a change in PSN (ΔPSN) was calculated. A body size adaptation effect was found, with observers who viewed fat bodies showing an increased PSN, and those exposed to thin bodies showing a reduced PSN. However, manipulations of featural attention to body fatness or sex typicality produced equivalent results, suggesting that featural attention may not affect the strength of the body size aftereffect. PMID:27597835

Hepatocellular Adenoma: Evaluation with Contrast-Enhanced Ultrasound and MRI and Correlation with Pathologic and Phenotypic Classification in 26 Lesions

PubMed Central

Manichon, Anne-Frédérique; Bancel, Brigitte; Durieux-Millon, Marion; Ducerf, Christian; Mabrut, Jean-Yves; Lepogam, Marie-Annick; Rode, Agnès

2012-01-01

Purpose. To review the contrast-enhanced ultrasonographic (CEUS) and magnetic resonance (MR) imaging findings in 25 patients with 26 hepatocellular adenomas (HCAs) and to compare imaging features with histopathologic results from resected specimen considering the new immunophenotypical classification. Material and Methods. Two abdominal radiologists reviewed retrospectively CEUS cineloops and MR images in 26 HCA. All pathological specimens were reviewed and classified into four subgroups (steatotic or HNF 1α mutated, inflammatory, atypical or β-catenin mutated, and unspecified). Inflammatory infiltrates were scored, steatosis, and telangiectasia semiquantitatively evaluated. Results. CEUS and MRI features are well correlated: among the 16 inflammatory HCA, 7/16 presented typical imaging features: hypersignal T2, strong arterial enhancement with a centripetal filling, persistent on delayed phase. 6 HCA were classified as steatotic with typical imaging features: a drop out signal, slight arterial enhancement, vanishing on late phase. Four HCA were classified as atypical with an HCC developed in one. Five lesions displayed important steatosis (>50%) without belonging to the HNF1α group. Conclusion. In half cases, inflammatory HCA have specific imaging features well correlated with the amount of telangiectasia and inflammatory infiltrates. An HCA with important amount of steatosis noticed on chemical shift images does not always belong to the HNF1α group. PMID:22811588

Filling of high aspect ratio micro features of a microfluidic flow cytometer chip using micro injection moulding

NASA Astrophysics Data System (ADS)

Zhang, Haoyang; Fang, Fengzhou; Gilchrist, Michael D.; Zhang, Nan

2018-07-01

Micro injection moulding has been demonstrated as one of the most efficient mass production technologies for manufacturing polymeric microfluidic devices, which have been widely used in life sciences, environmental and analytical fields and agro-food industries. However, the filling of micro features for typical microfluidic devices is complicated and not yet fully understood, which consequently restricts the chip development. In the present work, a microfluidic flow cytometer chip with essential high aspect ratio micro features was used as a typical model to study their filling process. Short-shot experiments and single factor experiments were performed to examine the filling progress of such features during the injection and packing stages of the micro injection moulding process. The influence of process parameters such as shot size, packing pressure, packing time and mould temperature were systematically monitored, characterised and correlated with 3D measurements and real response of the machine such as screw velocity and screw position. A combined melt flow and creep deformation model was proposed to explain the complex influence of process on replication. An approach of over-shot micro injection moulding was proposed and was shown to be effective at improving the replication quality of high aspect ratio micro features.

No Effect of Featural Attention on Body Size Aftereffects.

PubMed

Stephen, Ian D; Bickersteth, Chloe; Mond, Jonathan; Stevenson, Richard J; Brooks, Kevin R

2016-01-01

Prolonged exposure to images of narrow bodies has been shown to induce a perceptual aftereffect, such that observers' point of subjective normality (PSN) for bodies shifts toward narrower bodies. The converse effect is shown for adaptation to wide bodies. In low-level stimuli, object attention (attention directed to the object) and spatial attention (attention directed to the location of the object) have been shown to increase the magnitude of visual aftereffects, while object-based attention enhances the adaptation effect in faces. It is not known whether featural attention (attention directed to a specific aspect of the object) affects the magnitude of adaptation effects in body stimuli. Here, we manipulate the attention of Caucasian observers to different featural information in body images, by asking them to rate the fatness or sex typicality of male and female bodies manipulated to appear fatter or thinner than average. PSNs for body fatness were taken at baseline and after adaptation, and a change in PSN (ΔPSN) was calculated. A body size adaptation effect was found, with observers who viewed fat bodies showing an increased PSN, and those exposed to thin bodies showing a reduced PSN. However, manipulations of featural attention to body fatness or sex typicality produced equivalent results, suggesting that featural attention may not affect the strength of the body size aftereffect.

Allometric shape change of the lower pharyngeal jaw correlates with a dietary shift to piscivory in a cichlid fish.

PubMed

Hellig, Christoph J; Kerschbaumer, Michaela; Sefc, Kristina M; Koblmüller, Stephan

2010-07-01

The morphological versatility of the pharyngeal jaw of cichlid fishes is assumed to represent a key factor facilitating their unparalleled trophic diversification and explosive radiation. It is generally believed that the functional design of an organism relates to its ecology, and thus, specializations to different diets are typically associated with distinct morphological designs, especially manifested in the cichlids' pharyngeal jaw apparatus. Thereby, the lower pharyngeal jaw (LPJ) incorporates some of the most predictive features for distinct diet-related morphotypes. Thus, considering that piscivorous cichlids experience an ontogenetic dietary shift from typically various kinds of invertebrates to fish, concomitant morphological changes in the LPJ are expected. Using Lepidiolamprologus elongatus, a top predator in the shallow rocky habitat of Lake Tanganyika, as model, and applying geometric and traditional morphometric techniques, we demonstrate an allometric change in ontogenetic LPJ shape development coinciding with the completion of the dietary shift toward piscivory. The piscivorous LPJ morphotype is initiated in juvenile fish by increasing elongation and narrowing of the LPJ and--when the fish reach a size of 80-90 mm standard length--further refined by the elongation of the posterior muscular processes, which serve as insertion for the fourth musculus levator externus. The enlarged muscular processes of the fully mature piscivorous morphotype provide for the construction of a powerful lever system, which allows the large individuals to process large prey fish and rely on exclusive piscivory.

Allometric shape change of the lower pharyngeal jaw correlates with a dietary shift to piscivory in a cichlid fish

NASA Astrophysics Data System (ADS)

Hellig, Christoph J.; Kerschbaumer, Michaela; Sefc, Kristina M.; Koblmüller, Stephan

2010-07-01

The morphological versatility of the pharyngeal jaw of cichlid fishes is assumed to represent a key factor facilitating their unparalleled trophic diversification and explosive radiation. It is generally believed that the functional design of an organism relates to its ecology, and thus, specializations to different diets are typically associated with distinct morphological designs, especially manifested in the cichlids’ pharyngeal jaw apparatus. Thereby, the lower pharyngeal jaw (LPJ) incorporates some of the most predictive features for distinct diet-related morphotypes. Thus, considering that piscivorous cichlids experience an ontogenetic dietary shift from typically various kinds of invertebrates to fish, concomitant morphological changes in the LPJ are expected. Using Lepidiolamprologus elongatus, a top predator in the shallow rocky habitat of Lake Tanganyika, as model, and applying geometric and traditional morphometric techniques, we demonstrate an allometric change in ontogenetic LPJ shape development coinciding with the completion of the dietary shift toward piscivory. The piscivorous LPJ morphotype is initiated in juvenile fish by increasing elongation and narrowing of the LPJ and—when the fish reach a size of 80-90 mm standard length—further refined by the elongation of the posterior muscular processes, which serve as insertion for the fourth musculus levator externus. The enlarged muscular processes of the fully mature piscivorous morphotype provide for the construction of a powerful lever system, which allows the large individuals to process large prey fish and rely on exclusive piscivory.

Launch vehicle payload adapter design with vibration isolation features

NASA Astrophysics Data System (ADS)

Thomas, Gareth R.; Fadick, Cynthia M.; Fram, Bryan J.

2005-05-01

Payloads, such as satellites or spacecraft, which are mounted on launch vehicles, are subject to severe vibrations during flight. These vibrations are induced by multiple sources that occur between liftoff and the instant of final separation from the launch vehicle. A direct result of the severe vibrations is that fatigue damage and failure can be incurred by sensitive payload components. For this reason a payload adapter has been designed with special emphasis on its vibration isolation characteristics. The design consists of an annular plate that has top and bottom face sheets separated by radial ribs and close-out rings. These components are manufactured from graphite epoxy composites to ensure a high stiffness to weight ratio. The design is tuned to keep the frequency of the axial mode of vibration of the payload on the flexibility of the adapter to a low value. This is the main strategy adopted for isolating the payload from damaging vibrations in the intermediate to higher frequency range (45Hz-200Hz). A design challenge for this type of adapter is to keep the pitch frequency of the payload above a critical value in order to avoid dynamic interactions with the launch vehicle control system. This high frequency requirement conflicts with the low axial mode frequency requirement and this problem is overcome by innovative tuning of the directional stiffnesses of the composite parts. A second design strategy that is utilized to achieve good isolation characteristics is the use of constrained layer damping. This feature is particularly effective at keeping the responses to a minimum for one of the most important dynamic loading mechanisms. This mechanism consists of the almost-tonal vibratory load associated with the resonant burn condition present in any stage powered by a solid rocket motor. The frequency of such a load typically falls in the 45-75Hz range and this phenomenon drives the low frequency design of the adapter. Detailed finite element analysis is used throughout to qualify the design for vibration isolation performance as well as confirm its static and dynamic strength.

Habitat Utilization Assessment - Building in Behaviors

NASA Technical Reports Server (NTRS)

Whitmore, Mihriban; Blume, Jennifer

2004-01-01

Habitability, and the associated architectural and design attributes of an environment, is a powerful performance shaping factor. By identifying how inhabitants use an area, we can draw conclusions about what design or architectural attributes cause what behaviors and systematically design in desired human performance. We are analyzing how a crew uses a long duration habitat and work environment during a four-day underwater mission and identifying certain architectural and design attributes that are related to, and potential enablers of, certain crew behaviors. By identifying how inhabitants use the habitat, we can draw conclusions about what habitability attributes cause what behaviors and systematically design in desired human performance (applicable to NASA's Bioastronautics Human Behavior and Performance Critical Path Roadmap question 6.12). This assessment replicates a methodology reported in a chapter titled "Sociokinetic Analysis as a Tool for Optimization of Environmental Design" by C. Adams.' That study collected video imagery of certain areas of a closed habitat during a 91 day test and from that data calculated time spent in different volumes during the mission, and characterized the behaviors occurring in certain habitat volumes thus concluding various rules for design of such habitats. This study assesses the utilization of the Aquarius Habitat, an underwater station, which will support six Aquanauts for a fourteen-day mission during which the crew will perform specific scientific and engineering studies. Video is recorded for long uninterrupted periods of time during the mission and from that data the time spent in each area is calculated. In addition, qualitative and descriptive analysis of the types of behaviors in each area is performed with the purpose of identifying any behaviors that are not typical of a certain area. If a participant uses an area in a way different from expected, a subsequent analysis of the features of that area may result in conclusions of performance shaping factors. With the addition of this study, we can make comparisons between the two different habitats and begin drawing correlation judgments about design features and behavior. Ideally, this methodology should be repeated in additional Aquarius missions and other analog environments because the real information will come from comparisons between habitats.

10 CFR 830.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... Critical assembly means special nuclear devices designed and used to sustain nuclear reactions, which may... reaction becomes self-sustaining. Design features means the design features of a nuclear facility specified..., or the environment, including (1) Physical, design, structural, and engineering features; (2) Safety...

10 CFR 830.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Critical assembly means special nuclear devices designed and used to sustain nuclear reactions, which may... reaction becomes self-sustaining. Design features means the design features of a nuclear facility specified..., or the environment, including (1) Physical, design, structural, and engineering features; (2) Safety...

Low-Light-Shift Cesium Fountain without Mechanical Shutters

NASA Technical Reports Server (NTRS)

Enzer, Daphna

2008-01-01

A new technique for reducing errors in a laser-cooled cesium fountain frequency standard provides for strong suppression of the light shift without need for mechanical shutters. Because mechanical shutters are typically susceptible to failure after operating times of the order of months, the elimination of mechanical shutters could contribute significantly to the reliability of frequency standards that are required to function continuously for longer time intervals. With respect to the operation of an atomic-fountain frequency standard, the term "light shift" denotes an undesired relative shift in the two energy levels of the atoms (in this case, cesium atoms) in the atomic fountain during interrogation by microwaves. The shift in energy levels translates to a frequency shift that reduces the precision and possibly accuracy of the frequency standard. For reasons too complex to describe within the space available for this article, the light shift is caused by any laser light that reaches the atoms during the microwave- interrogation period, but is strongest for near-resonance light. In the absence of any mitigating design feature, the light shift, expressed as a fraction of the standard fs frequency, could be as large as approx. 2 x 10(exp -11), the largest error in the standard. In a typical prior design, to suppress light shift, the intensity of laser light is reduced during the interrogation period by using a single-pass acoustooptic modulator to deflect the majority of light away from the main optical path. Mechanical shutters are used to block the remaining undeflected light to ensure complete attenuation. Without shutters, this remaining undeflected light could cause a light shift of as much as .10.15, which is unacceptably large in some applications. The new technique implemented here involves additionally shifting the laser wavelength off resonance by a relatively large amount (typically of the order of nanometers) during microwave interrogation. In this design, when microwave interrogation is not underway, the atoms are illuminated by a slave laser locked to the lasing frequency of a lower power master laser.

The crystallization and structural analysis of cellulases (and other glycoside hydrolases): strategies and tactics.

PubMed

Roberts, Shirley M; Davies, Gideon J

2012-01-01

The three-dimensional (3-D) structures of cellulases, and other glycoside hydrolases, are a central feature of research in carbohydrate chemistry and biochemistry. 3-D structure is used to inform protein engineering campaigns, both academic and industrial, which are typically used to improve the stability or activity of an enzyme. Examples of classical protein engineering goals include higher thermal stability, reduced metal-ion dependency, detergent and protease resistance, decreased product inhibition, and altered specificity. 3-D structure may also be used to interpret the behavior of enzyme variants that are derived from screening or random mutagenesis approaches, with a view to establishing an iterative design process. In other areas, 3-D structure is used as one of the many tools to probe enzymatic catalysis, typically dovetailing with physical organic chemistry approaches to provide complete reaction mechanisms for enzymes by visualizing catalytic site interactions at different stages of the reaction. Such mechanistic insight is not only fundamentally important, impacting on inhibitor and drug design approaches with ramifications way beyond cellulose hydrolysis, but also provides the framework for the design of enzyme variants to use as biocatalysts for the synthesis of bespoke oligosaccharides. Here we review some of the strategies and tactics that may be applied to the X-ray structure solution of cellulases (and other carbohydrate-active enzymes). The general approach is first to decide why you are doing the work, then to establish correct domain boundaries for truncated constructs (typically the catalytic domain only), and finally to pursue crystallization of pure, homogeneous, and monodisperse protein with appropriate ligand and additive combinations. Cellulase-specific strategies are important for the delineation of domain boundaries, while glycoside hydrolases generally also present challenges and opportunities for the selection and optimization of ligands to both aid crystallization, and also provide structural and mechanistic insight. As the many roles for plant cell wall degrading enzymes increase, so does the need for rapid high-quality structure determination to provide a sound structural foundation for understanding mechanism and specificity, and for future protein engineering strategies. Copyright © 2012 Elsevier Inc. All rights reserved.

Fault Diagnosis for Rotating Machinery: A Method based on Image Processing

PubMed Central

Lu, Chen; Wang, Yang; Ragulskis, Minvydas; Cheng, Yujie

2016-01-01

Rotating machinery is one of the most typical types of mechanical equipment and plays a significant role in industrial applications. Condition monitoring and fault diagnosis of rotating machinery has gained wide attention for its significance in preventing catastrophic accident and guaranteeing sufficient maintenance. With the development of science and technology, fault diagnosis methods based on multi-disciplines are becoming the focus in the field of fault diagnosis of rotating machinery. This paper presents a multi-discipline method based on image-processing for fault diagnosis of rotating machinery. Different from traditional analysis method in one-dimensional space, this study employs computing method in the field of image processing to realize automatic feature extraction and fault diagnosis in a two-dimensional space. The proposed method mainly includes the following steps. First, the vibration signal is transformed into a bi-spectrum contour map utilizing bi-spectrum technology, which provides a basis for the following image-based feature extraction. Then, an emerging approach in the field of image processing for feature extraction, speeded-up robust features, is employed to automatically exact fault features from the transformed bi-spectrum contour map and finally form a high-dimensional feature vector. To reduce the dimensionality of the feature vector, thus highlighting main fault features and reducing subsequent computing resources, t-Distributed Stochastic Neighbor Embedding is adopt to reduce the dimensionality of the feature vector. At last, probabilistic neural network is introduced for fault identification. Two typical rotating machinery, axial piston hydraulic pump and self-priming centrifugal pumps, are selected to demonstrate the effectiveness of the proposed method. Results show that the proposed method based on image-processing achieves a high accuracy, thus providing a highly effective means to fault diagnosis for rotating machinery. PMID:27711246

Fault Diagnosis for Rotating Machinery: A Method based on Image Processing.

PubMed

Lu, Chen; Wang, Yang; Ragulskis, Minvydas; Cheng, Yujie

2016-01-01

Rotating machinery is one of the most typical types of mechanical equipment and plays a significant role in industrial applications. Condition monitoring and fault diagnosis of rotating machinery has gained wide attention for its significance in preventing catastrophic accident and guaranteeing sufficient maintenance. With the development of science and technology, fault diagnosis methods based on multi-disciplines are becoming the focus in the field of fault diagnosis of rotating machinery. This paper presents a multi-discipline method based on image-processing for fault diagnosis of rotating machinery. Different from traditional analysis method in one-dimensional space, this study employs computing method in the field of image processing to realize automatic feature extraction and fault diagnosis in a two-dimensional space. The proposed method mainly includes the following steps. First, the vibration signal is transformed into a bi-spectrum contour map utilizing bi-spectrum technology, which provides a basis for the following image-based feature extraction. Then, an emerging approach in the field of image processing for feature extraction, speeded-up robust features, is employed to automatically exact fault features from the transformed bi-spectrum contour map and finally form a high-dimensional feature vector. To reduce the dimensionality of the feature vector, thus highlighting main fault features and reducing subsequent computing resources, t-Distributed Stochastic Neighbor Embedding is adopt to reduce the dimensionality of the feature vector. At last, probabilistic neural network is introduced for fault identification. Two typical rotating machinery, axial piston hydraulic pump and self-priming centrifugal pumps, are selected to demonstrate the effectiveness of the proposed method. Results show that the proposed method based on image-processing achieves a high accuracy, thus providing a highly effective means to fault diagnosis for rotating machinery.

Evaluating disease management programme effectiveness: an introduction to the regression discontinuity design.

PubMed

Linden, Ariel; Adams, John L; Roberts, Nancy

2006-04-01

Although disease management (DM) has been in existence for over a decade, there is still much uncertainty as to its effectiveness in improving health status and reducing medical cost. The main reason is that most programme evaluations typically follow weak observational study designs that are subject to bias, most notably selection bias and regression to the mean. The regression discontinuity (RD) design may be the best alternative to randomized studies for evaluating DM programme effectiveness. The most crucial element of the RD design is its use of a 'cut-off' score on a pre-test measure to determine assignment to intervention or control. A valuable feature of this technique is that the pre-test measure does not have to be the same as the outcome measure, thus maximizing the programme's ability to use research-based practice guidelines, survey instruments and other tools to identify those individuals in greatest need of the programme intervention. Similarly, the cut-off score can be based on clinical understanding of the disease process, empirically derived, or resource-based. In the RD design, programme effectiveness is determined by a change in the pre-post relationship at the cut-off point. While the RD design is uniquely suitable for DM programme evaluation, its success will depend, in large part, on fundamental changes being made in the way DM programmes identify and assign individuals to the programme intervention.

What to Build for Middle-Agers to Come? Attractive and Necessary Functions of Exercise-Promotion Mobile Phone Apps: A Cross-Sectional Study

PubMed Central

Chien, Yu-Tai; Chen, Yu-Jen; Hsiung, Hsiao-Fang; Chen, Hsiao-Jung; Hsieh, Meng-Hua; Wu, Wen-Jie

2017-01-01

Background Physical activity is important for middle-agers to maintain health both in middle age and in old age. Although thousands of exercise-promotion mobile phone apps are available for download, current literature offers little understanding regarding which design features can enhance middle-aged adults’ quality perception toward exercise-promotion apps and which factor may influence such perception. Objectives The aims of this study were to understand (1) which design features of exercise-promotion apps can enhance quality perception of middle-agers, (2) whether their needs are matched by current functions offered in app stores, and (3) whether physical activity (PA) and mobile phone self-efficacy (MPSE) influence quality perception. Methods A total of 105 middle-agers participated and filled out three scales: the International Physical Activity Questionnaire (IPAQ), the MPSE scale, and the need for design features questionnaire. The design features were developed based on the Coventry, Aberdeen, and London—Refined (CALO-RE) taxonomy. Following the Kano quality model, the need for design features questionnaire asked participants to classify design features into five categories: attractive, one-dimensional, must-be, indifferent, and reverse. The quality categorization was conducted based on a voting approach and the categorization results were compared with the findings of a prevalence study to realize whether needs match current availability. In total, 52 multinomial logistic regression models were analyzed to evaluate the effects of PA level and MPSE on quality perception of design features. Results The Kano analysis on the total sample revealed that visual demonstration of exercise instructions is the only attractive design feature, whereas the other 51 design features were perceived with indifference. Although examining quality perception by PA level, 21 features are recommended to low level, 6 features to medium level, but none to high-level PA. In contrast, high-level MPSE is recommended with 14 design features, medium level with 6 features, whereas low-level participants are recommended with 1 feature. The analysis suggests that the implementation of demanded features could be low, as the average prevalence of demanded design features is 20% (4.3/21). Surprisingly, social comparison and social support, most implemented features in current apps, were categorized into the indifferent category. The magnitude of effect is larger for MPSE because it effects quality perception of more design features than PA. Delving into the 52 regression models revealed that high MPSE more likely induces attractive or one- dimensional categorization, suggesting the importance of technological self-efficacy on eHealth care promotion. Conclusions This study is the first to propose middle-agers’ needs in relation to mobile phone exercise-promotion. In addition to the tailor-made recommendations, suggestions are offered to app designers to enhance the performance of persuasive features. An interesting finding on change of quality perception attributed to MPSE is proposed as future research. PMID:28546140

Microwave/millimeter wave technology

NASA Astrophysics Data System (ADS)

Abita, Joseph L.

1988-09-01

The microwave/millimeter-wave monolithic integrated-circuit (MIMIC) technology and systems are discussed along with the application of MIMICs in electronic warfare. The components of a MIMIC are described, with particular attention given to the active-array antenna transmit/receive module, which is at the focus of the MIMIC, and to the features of a typical MIMIC chip. The typical performance characteristics of MIMIC components are presented in tabular form.

Method to Increase Performance of Foil Bearings Through Passive Thermal Management

NASA Technical Reports Server (NTRS)

Bruckner, Robert

2013-01-01

This invention is a new approach to designing foil bearings to increase their load capacity and improve their reliability through passive thermal management. In the present case, the bearing is designed in such a way as to prevent the carryover of lubricant from the exit of one sector to the inlet of the ensuing sector of the foil bearing. When such passive thermal management techniques are used, bearing load capacity is improved by multiples, and reliability is enhanced when compared to current foil bearings. This concept has recently been tested and validated, and shows that load capacity performance of foil bearings can be improved by a factor of two at relatively low speeds with potentially greater relative improvements at higher speeds. Such improvements in performance with respect to speed are typical of foil bearings. Additionally, operation of these newly conceived bearings shows much more reliability and repeatable performance. This trait can be exploited in machine design to enhance safety, reliability, and overall performance. Finally, lower frictional torque has been demonstrated when operating at lower (non-load capacity) loads, thus providing another improvement above the current state of the art. The objective of the invention is to incorporate features into a foil bearing that both enhance passive thermal management and temperature control, while at the same time improve the hydrodynamic (load capacity) performance of the foil bearing. Foil bearings are unique antifriction devices that can utilize the working fluid of a machine as a lubricant (typically air for turbines and motors, liquids for pumps), and as a coolant to remove excess energy due to frictional heating. The current state of the art of foil bearings utilizes forced cooling of the bearing and shaft, which represents poor efficiency and poor reliability. This invention embodies features that utilize the bearing geometry in such a manner as to both support load and provide an inherent and passive cooling mechanism. This cooling mechanism functions in such a way as to prevent used (higher temperature) lubricant from being carried over from the exit of one sector into the entry of the next sector of the foil bearing. The disclosed innovation is an improved foil bearing design that reduces or eliminates the need for force cooling of the bearing, while at the same time improving the load capacity of the bearing by at least a factor of two. These improvements are due to the elimination of lubricant carryover from the trailing edge of one sector into the leading edge of the next, and the mixing of used lubricant with the surrounding ambient fluid.

Adamantinoma with plasmacytoid features: expanding the spectrum of a diagnostically challenging entity.

PubMed

Walters, Matthew P; Baynes, Keith; Carrera, Guillermo F; King, David M; Wang, Dian; Charlson, John; Zambrano, Eduardo

2011-10-01

Adamantinoma is a rare neoplasm that characteristically involves the tibia. In many instances, typical location within the tibia, very slow course, and a typical radiographic appearance can strongly suggest the correct diagnosis. We present a case that has both unusual radiographic findings and uncharacteristic histology. In this case, radiologic imaging showed a poorly defined lytic lesion within the distal, lateral tibia extending to the joint with central necrosis, overlying periosteal reaction and possible tumor spread into soft tissue. The histology of this lesion showed pronounced vascularity and surrounding large neoplastic cells with plasmacytoid morphology. The combination of these features led to an initial misdiagnosis as metastatic carcinoma from unknown primary. Copyright © 2011 Elsevier Inc. All rights reserved.

Ultra-wideband three-dimensional optoacoustic tomography.

PubMed

Gateau, Jérôme; Chekkoury, Andrei; Ntziachristos, Vasilis

2013-11-15

Broadband optoacoustic waves generated by biological tissues excited with nanosecond laser pulses carry information corresponding to a wide range of geometrical scales. Typically, the frequency content present in the signals generated during optoacoustic imaging is much larger compared to the frequency band captured by common ultrasonic detectors, the latter typically acting as bandpass filters. To image optical absorption within structures ranging from entire organs to microvasculature in three dimensions, we implemented optoacoustic tomography with two ultrasound linear arrays featuring a center frequency of 6 and 24 MHz, respectively. In the present work, we show that complementary information on anatomical features could be retrieved and provide a better understanding on the localization of structures in the general anatomy by analyzing multi-bandwidth datasets acquired on a freshly excised kidney.

Tracking Subtle Stereotypes of Children with Trisomy 21: From Facial-Feature-Based to Implicit Stereotyping

PubMed Central

Enea-Drapeau, Claire; Carlier, Michèle; Huguet, Pascal

2012-01-01

Background Stigmatization is one of the greatest obstacles to the successful integration of people with Trisomy 21 (T21 or Down syndrome), the most frequent genetic disorder associated with intellectual disability. Research on attitudes and stereotypes toward these people still focuses on explicit measures subjected to social-desirability biases, and neglects how variability in facial stigmata influences attitudes and stereotyping. Methodology/Principal Findings The participants were 165 adults including 55 young adult students, 55 non-student adults, and 55 professional caregivers working with intellectually disabled persons. They were faced with implicit association tests (IAT), a well-known technique whereby response latency is used to capture the relative strength with which some groups of people—here photographed faces of typically developing children and children with T21—are automatically (without conscious awareness) associated with positive versus negative attributes in memory. Each participant also rated the same photographed faces (consciously accessible evaluations). We provide the first evidence that the positive bias typically found in explicit judgments of children with T21 is smaller for those whose facial features are highly characteristic of this disorder, compared to their counterparts with less distinctive features and to typically developing children. We also show that this bias can coexist with negative evaluations at the implicit level (with large effect sizes), even among professional caregivers. Conclusion These findings support recent models of feature-based stereotyping, and more importantly show how crucial it is to go beyond explicit evaluations to estimate the true extent of stigmatization of intellectually disabled people. PMID:22496796

Concept typicality responses in the semantic memory network.

PubMed

Santi, Andrea; Raposo, Ana; Frade, Sofia; Marques, J Frederico

2016-12-01

For decades concept typicality has been recognized as critical to structuring conceptual knowledge, but only recently has typicality been applied in better understanding the processes engaged by the neurological network underlying semantic memory. This previous work has focused on one region within the network - the Anterior Temporal Lobe (ATL). The ATL responds negatively to concept typicality (i.e., the more atypical the item, the greater the activation in the ATL). To better understand the role of typicality in the entire network, we ran an fMRI study using a category verification task in which concept typicality was manipulated parametrically. We argue that typicality is relevant to both amodal feature integration centers as well as category-specific regions. Both the Inferior Frontal Gyrus (IFG) and ATL demonstrated a negative correlation with typicality, whereas inferior parietal regions showed positive effects. We interpret this in light of functional theories of these regions. Interactions between category and typicality were not observed in regions classically recognized as category-specific, thus, providing an argument against category specific regions, at least with fMRI. Copyright © 2016 Elsevier Ltd. All rights reserved.

Chlapsin, a chloroplastidial aspartic proteinase from the green algae Chlamydomonas reinhardtii.

PubMed

Almeida, Carla Malaquias; Pereira, Cláudia; da Costa, Diana Soares; Pereira, Susana; Pissarra, José; Simões, Isaura; Faro, Carlos

2012-07-01

Aspartic proteinases have been extensively characterized in land plants but up to now no evidences for their presence in green algae group have yet been reported in literature. Here we report on the identification of the first (and only) typical aspartic proteinase from Chlamydomonas reinhardtii. This enzyme, named chlapsin, was shown to maintain the primary structure organization of typical plant aspartic proteinases but comprising distinct features, such as similar catalytic motifs DTG/DTG resembling those from animal and microbial counterparts, and an unprecedentedly longer plant specific insert domain with an extra segment of 80 amino acids, rich in alanine residues. Our results also demonstrated that chlapsin accumulates in Chlamydomonas chloroplast bringing this new enzyme to a level of uniqueness among typical plant aspartic proteinases. Chlapsin was successfully expressed in Escherichia coli and it displayed the characteristic enzymatic properties of typical aspartic proteinases, like optimum activity at acidic pH and complete inhibition by pepstatin A. Another difference to plant aspartic proteinases emerged as chlapsin was produced in an active form without its putative prosegment domain. Moreover, recombinant chlapsin showed a restricted enzymatic specificity and a proteolytic activity influenced by the presence of redox agents and nucleotides, further differentiating it from typical plant aspartic proteinases and anticipating a more specialized/regulated function for this Chlamydomonas enzyme. Taken together, our results revealed a pattern of complexity for typical plant aspartic proteinases in what concerns sequence features, localization and biochemical properties, raising new questions on the evolution and function of this vast group of plant enzymes.

Considering the Lives of Microbes in Microbial Communities.

PubMed

Shank, Elizabeth A

2018-01-01

Over the last decades, sequencing technologies have transformed our ability to investigate the composition and functional capacity of microbial communities. Even so, critical questions remain about these complex systems that cannot be addressed by the bulk, community-averaged data typically provided by sequencing methods. In this Perspective, I propose that future advances in microbiome research will emerge from considering "the lives of microbes": we need to create methods to explicitly interrogate how microbes exist and interact in native-setting-like microenvironments. This approach includes developing approaches that expose the phenotypic heterogeneity of microbes; exploring the effects of coculture cues on cellular differentiation and metabolite production; and designing visualization systems that capture features of native microbial environments while permitting the nondestructive observation of microbial interactions over space and time with single-cell resolution.

A comparative study and validation of upwind and central-difference Navier-Stokes codes for high-speed flows

NASA Technical Reports Server (NTRS)

Rudy, David H.; Kumar, Ajay; Thomas, James L.; Gnoffo, Peter A.; Chakravarthy, Sukumar R.

1988-01-01

A comparative study was made using 4 different computer codes for solving the compressible Navier-Stokes equations. Three different test problems were used, each of which has features typical of high speed internal flow problems of practical importance in the design and analysis of propulsion systems for advanced hypersonic vehicles. These problems are the supersonic flow between two walls, one of which contains a 10 deg compression ramp, the flow through a hypersonic inlet, and the flow in a 3-D corner formed by the intersection of two symmetric wedges. Three of the computer codes use similar recently developed implicit upwind differencing technology, while the fourth uses a well established explicit method. The computed results were compared with experimental data where available.

Commerical (terrestrial) and modified solar array design studies for low cost, low power space applications

NASA Technical Reports Server (NTRS)

Kolecki, J. C.; Riley, T. J.

1980-01-01

The suitability of commercial (terrestrial) solar arrays for use in low Earth orbit is examined. It is shown that commercial solar arrays degrade under thermal cycling because of material flexure, and that certain types of silicones used in the construction of these arrays outgas severely. Based on the results, modifications were made. The modified array retains the essential features of typical commercial arrays and can be easily built by commercial fabrication techniques at low cost. The modified array uses a metal tray for containment, but eliminates the high outgassing potting materials and glass cover sheets. Cells are individually mounted with an adhesive and individually covered with glass cover slips, or clear plastic tape. The modified array is found to withstand severe thermal cycling for long intervals of time.

Dual-mode nested search method for categorical uncertain multi-objective optimization

NASA Astrophysics Data System (ADS)

Tang, Long; Wang, Hu

2016-10-01

Categorical multi-objective optimization is an important issue involved in many matching design problems. Non-numerical variables and their uncertainty are the major challenges of such optimizations. Therefore, this article proposes a dual-mode nested search (DMNS) method. In the outer layer, kriging metamodels are established using standard regular simplex mapping (SRSM) from categorical candidates to numerical values. Assisted by the metamodels, a k-cluster-based intelligent sampling strategy is developed to search Pareto frontier points. The inner layer uses an interval number method to model the uncertainty of categorical candidates. To improve the efficiency, a multi-feature convergent optimization via most-promising-area stochastic search (MFCOMPASS) is proposed to determine the bounds of objectives. Finally, typical numerical examples are employed to demonstrate the effectiveness of the proposed DMNS method.

Unsaturated consolidation theory for the prediction of long-term municipal solid waste landfill settlement.

PubMed

Liu, Chia-Nan; Chen, Rong-Her; Chen, Kuo-Sheng

2006-02-01

The understanding of long-term landfill settlement is important for landfill design and rehabilitation. However, suitable models that can consider both the mechanical and biodecomposition mechanisms in predicting the long-term landfill settlement are generally not available. In this paper, a model based on unsaturated consolidation theory and considering the biodegradation process is introduced to simulate the landfill settlement behaviour. The details of problem formulations and the derivation of the solution for the formulated differential equation of gas pressure are presented. A step-by-step analytical procedure employing this approach for estimating settlement is proposed. The proposed model can generally model the typical features of short-term and long-term behaviour. The proposed model also yields results that are comparable with the field measurements.

FInal Report - Investment Casting Shell Cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Von Richards

2003-12-01

This project made a significant contribution to the understanding of the investment casting shell cracking problem. The effects of wax properties on the occurrence of shell cracking were demonstrated and can be measured. The properties measured include coefficient of thermal expansion, heating rate and crystallinity of the structure. The important features of production molds and materials properties have been indicated by case study analysis and fractography of low strength test bars. It was found that stress risers in shell cavity design were important and that typical critical flaws were either oversize particles or large pores just behind the prime coat.more » It was also found that the true effect of fugitive polymer fibers was not permeability increase, but rather a toughening mechanism due to crack deflection.« less

Temporal trade-offs in psychophysics.

PubMed

Barack, David L; Gold, Joshua I

2016-04-01

Psychophysical techniques typically assume straightforward relationships between manipulations of real-world events, their effects on the brain, and behavioral reports of those effects. However, these relationships can be influenced by many complex, strategic factors that contribute to task performance. Here we discuss several of these factors that share two key features. First, they involve subjects making flexible use of time to process information. Second, this flexibility can reflect the rational regulation of information-processing trade-offs that can play prominent roles in particular temporal epochs: sensitivity to stability versus change for past information, speed versus accuracy for current information, and exploitation versus exploration for future goals. Understanding how subjects manage these trade-offs can be used to help design and interpret psychophysical studies. Copyright © 2016 Elsevier Ltd. All rights reserved.

The 1991 3rd NASA Symposium on VLSI Design

NASA Technical Reports Server (NTRS)

Maki, Gary K.

1991-01-01

Papers from the symposium are presented from the following sessions: (1) featured presentations 1; (2) very large scale integration (VLSI) circuit design; (3) VLSI architecture 1; (4) featured presentations 2; (5) neural networks; (6) VLSI architectures 2; (7) featured presentations 3; (8) verification 1; (9) analog design; (10) verification 2; (11) design innovations 1; (12) asynchronous design; and (13) design innovations 2.

Development of advanced micromirror arrays by flip-chip assembly

NASA Astrophysics Data System (ADS)

Michalicek, M. Adrian; Bright, Victor M.

2001-10-01

This paper presents the design, commercial prefabrication, modeling and testing of advanced micromirror arrays fabricated using a novel, simple and inexpensive flip-chip assembly technique. Several polar piston arrays and rectangular cantilever arrays were fabricated using flip-chip assembly by which the upper layers of the array are fabricated on a separate chip and then transferred to a receiving module containing the lower layers. Typical polar piston arrays boast 98.3% active surface area, highly planarized surfaces, low address potentials compatible with CMOS electronics, highly standardized actuation between devices, and complex segmentation of mirror surfaces which allows for custom aberration configurations. Typical cantilever arrays boast large angles of rotation as well as an average surface planarity of only 1.779 nm of RMS roughness across 100 +m mirrors. Continuous torsion devices offer stable operation through as much as six degrees of rotation while binary operation devices offer stable activated positions with as much as 20 degrees of rotation. All arrays have desirable features of costly fabrication services like five structural layers and planarized mirror surfaces, but are prefabricated in the less costly MUMPs process. Models are developed for all devices and used to compare empirical data.

Xpatch prediction improvements to support multiple ATR applications

NASA Astrophysics Data System (ADS)

Andersh, Dennis J.; Lee, Shung W.; Moore, John T.; Sullivan, Douglas P.; Hughes, Jeff A.; Ling, Hao

1998-08-01

This paper describes an electromagnetic computer prediction code for generating radar cross section (RCS), time-domain signature sand synthetic aperture radar (SAR) images of realistic 3D vehicles. The vehicle, typically an airplane or a ground vehicle, is represented by a computer-aided design (CAD) file with triangular facets, IGES curved surfaces, or solid geometries.The computer code, Xpatch, based on the shooting-and-bouncing-ray technique, is used to calculate the polarimetric radar return from the vehicles represented by these different CAD files. Xpatch computers the first- bounce physical optics (PO) plus the physical theory of diffraction (PTD) contributions. Xpatch calculates the multi-bounce ray contributions by using geometric optics and PO for complex vehicles with materials. It has been found that the multi-bounce calculations, the radar return in typically 10 to 15 dB too low. Examples of predicted range profiles, SAR, imagery, and RCS for several different geometries are compared with measured data to demonstrate the quality of the predictions. Recent enhancements to Xpatch include improvements for millimeter wave applications and hybridization with finite element method for small geometric features and augmentation of additional IGES entities to support trimmed and untrimmed surfaces.

A comparative study of thermal characteristics of GaN-based VCSELs with three different typical structures

NASA Astrophysics Data System (ADS)

Mei, Yang; Xu, Rong-Bin; Xu, Huan; Ying, Lei-Ying; Zheng, Zhi-Wei; Zhang, Bao-Ping; Li, Mo; Zhang, Jian

2018-01-01

Thermal characteristics of GaN-based vertical cavity surface emitting lasers (VCSELs) with three typical structures were investigated both theoretically and experimentally. The simulation results based on a steady state quasi three-dimensional cylindrical model show that the thermal resistance (R th) is affected by cavity length, mesa size, as well as the bottom distributed Bragg reflector (DBR) size, and the detail further depends on different structures. Among different devices, GaN VCSEL with a hybrid cavity formed by one nitride bottom DBR and another dielectric top DBR is featured with lower R th, which is meanwhile affected strongly by the materials of the epitaxial bottom DBR. The main issues affecting the thermal dissipation in VCSELs with double dielectric DBRs are the bottom dielectric DBR and the dielectric current-confinement layer. To validate the simulation results, GaN-based VCSEL bonded on a copper plate was fabricated. R th of this device was measured and the results agreed well with the simulation. This work provides a better understanding of the thermal characteristics of GaN-based VCSELs and is useful in optimizing the structure design and improving the device performance.

Compact cancer biomarkers discovery using a swarm intelligence feature selection algorithm.

PubMed

Martinez, Emmanuel; Alvarez, Mario Moises; Trevino, Victor

2010-08-01

Biomarker discovery is a typical application from functional genomics. Due to the large number of genes studied simultaneously in microarray data, feature selection is a key step. Swarm intelligence has emerged as a solution for the feature selection problem. However, swarm intelligence settings for feature selection fail to select small features subsets. We have proposed a swarm intelligence feature selection algorithm based on the initialization and update of only a subset of particles in the swarm. In this study, we tested our algorithm in 11 microarray datasets for brain, leukemia, lung, prostate, and others. We show that the proposed swarm intelligence algorithm successfully increase the classification accuracy and decrease the number of selected features compared to other swarm intelligence methods. Copyright © 2010 Elsevier Ltd. All rights reserved.

Boosting K-12 Student Achievement: How Corporate America and Higher Ed Can Help. Forum Focus. Fall 2006

ERIC Educational Resources Information Center

Ehrlich, Jenifer, Ed.

2006-01-01

"Forum Focus" was a semi-annual magazine of the Business-Higher Education Forum (BHEF) that featured articles on the role of business and higher education on significant issues affecting the P-16 education system. The magazine typically focused on themes featured at the most recently held semi-annual Forum meeting at the time of…

Visual Analytics for Heterogeneous Geoscience Data

NASA Astrophysics Data System (ADS)

Pan, Y.; Yu, L.; Zhu, F.; Rilee, M. L.; Kuo, K. S.; Jiang, H.; Yu, H.

2017-12-01

Geoscience data obtained from diverse sources have been routinely leveraged by scientists to study various phenomena. The principal data sources include observations and model simulation outputs. These data are characterized by spatiotemporal heterogeneity originated from different instrument design specifications and/or computational model requirements used in data generation processes. Such inherent heterogeneity poses several challenges in exploring and analyzing geoscience data. First, scientists often wish to identify features or patterns co-located among multiple data sources to derive and validate certain hypotheses. Heterogeneous data make it a tedious task to search such features in dissimilar datasets. Second, features of geoscience data are typically multivariate. It is challenging to tackle the high dimensionality of geoscience data and explore the relations among multiple variables in a scalable fashion. Third, there is a lack of transparency in traditional automated approaches, such as feature detection or clustering, in that scientists cannot intuitively interact with their analysis processes and interpret results. To address these issues, we present a new scalable approach that can assist scientists in analyzing voluminous and diverse geoscience data. We expose a high-level query interface that allows users to easily express their customized queries to search features of interest across multiple heterogeneous datasets. For identified features, we develop a visualization interface that enables interactive exploration and analytics in a linked-view manner. Specific visualization techniques such as scatter plots to parallel coordinates are employed in each view to allow users to explore various aspects of features. Different views are linked and refreshed according to user interactions in any individual view. In such a manner, a user can interactively and iteratively gain understanding into the data through a variety of visual analytics operations. We demonstrate with use cases how scientists can combine the query and visualization interfaces to enable a customized workflow facilitating studies using heterogeneous geoscience datasets.

Do Particular Design Features Assist People with Aphasia to Comprehend Text? An Exploratory Study

ERIC Educational Resources Information Center

Wilson, Lucy; Read, Jennifer

2016-01-01

Background: Much of the evidence underlying guidelines for producing accessible information for people with aphasia focuses on client preference for particular design features. There is limited evidence regarding the effects of these features on comprehension. Aims: To examine the effects of specific design features on text comprehension. It was…

Escalator Design Features Evaluation

DOT National Transportation Integrated Search

1982-05-01

This study provides an evaluation of the effectiveness of several special design features associated with escalators in rail transit systems. The objective of the study was to evaluate the effectiveness of three escalator design features: (1) mat ope...

Towards a standard design model for quad-rotors: A review of current models, their accuracy and a novel simplified model

NASA Astrophysics Data System (ADS)

Amezquita-Brooks, Luis; Liceaga-Castro, Eduardo; Gonzalez-Sanchez, Mario; Garcia-Salazar, Octavio; Martinez-Vazquez, Daniel

2017-11-01

Applications based on quad-rotor-vehicles (QRV) are becoming increasingly wide-spread. Many of these applications require accurate mathematical representations for control design, simulation and estimation. However, there is no consensus on a standardized model for these purposes. In this article a review of the most common elements included in QRV models reported in the literature is presented. This survey shows that some elements are recurrent for typical non-aerobatic QRV applications; in particular, for control design and high-performance simulation. By synthesising the common features of the reviewed models a standard generic model SGM is proposed. The SGM is cast as a typical state-space model without memory-less transformations, a structure which is useful for simulation and controller design. The survey also shows that many QRV applications use simplified representations, which may be considered simplifications of the SGM here proposed. In order to assess the effectiveness of the simplified models, a comprehensive comparison based on digital simulations is presented. With this comparison, it is possible to determine the accuracy of each model under particular operating ranges. Such information is useful for the selection of a model according to a particular application. In addition to the models found in the literature, in this article a novel simplified model is derived. The main characteristics of this model are that its inner dynamics are linear, it has low complexity and it has a high level of accuracy in all the studied operating ranges, a characteristic found only in more complex representations. To complement the article the main elements of the SGM are evaluated with the aid of experimental data and the computational complexity of all surveyed models is briefly analysed. Finally, the article presents a discussion on how the structural characteristics of the models are useful to suggest particular QRV control structures.

What to Build for Middle-Agers to Come? Attractive and Necessary Functions of Exercise-Promotion Mobile Phone Apps: A Cross-Sectional Study.

PubMed

Liao, Gen-Yih; Chien, Yu-Tai; Chen, Yu-Jen; Hsiung, Hsiao-Fang; Chen, Hsiao-Jung; Hsieh, Meng-Hua; Wu, Wen-Jie

2017-05-25

Physical activity is important for middle-agers to maintain health both in middle age and in old age. Although thousands of exercise-promotion mobile phone apps are available for download, current literature offers little understanding regarding which design features can enhance middle-aged adults' quality perception toward exercise-promotion apps and which factor may influence such perception. The aims of this study were to understand (1) which design features of exercise-promotion apps can enhance quality perception of middle-agers, (2) whether their needs are matched by current functions offered in app stores, and (3) whether physical activity (PA) and mobile phone self-efficacy (MPSE) influence quality perception. A total of 105 middle-agers participated and filled out three scales: the International Physical Activity Questionnaire (IPAQ), the MPSE scale, and the need for design features questionnaire. The design features were developed based on the Coventry, Aberdeen, and London-Refined (CALO-RE) taxonomy. Following the Kano quality model, the need for design features questionnaire asked participants to classify design features into five categories: attractive, one-dimensional, must-be, indifferent, and reverse. The quality categorization was conducted based on a voting approach and the categorization results were compared with the findings of a prevalence study to realize whether needs match current availability. In total, 52 multinomial logistic regression models were analyzed to evaluate the effects of PA level and MPSE on quality perception of design features. The Kano analysis on the total sample revealed that visual demonstration of exercise instructions is the only attractive design feature, whereas the other 51 design features were perceived with indifference. Although examining quality perception by PA level, 21 features are recommended to low level, 6 features to medium level, but none to high-level PA. In contrast, high-level MPSE is recommended with 14 design features, medium level with 6 features, whereas low-level participants are recommended with 1 feature. The analysis suggests that the implementation of demanded features could be low, as the average prevalence of demanded design features is 20% (4.3/21). Surprisingly, social comparison and social support, most implemented features in current apps, were categorized into the indifferent category. The magnitude of effect is larger for MPSE because it effects quality perception of more design features than PA. Delving into the 52 regression models revealed that high MPSE more likely induces attractive or one- dimensional categorization, suggesting the importance of technological self-efficacy on eHealth care promotion. This study is the first to propose middle-agers' needs in relation to mobile phone exercise-promotion. In addition to the tailor-made recommendations, suggestions are offered to app designers to enhance the performance of persuasive features. An interesting finding on change of quality perception attributed to MPSE is proposed as future research. ©Gen-Yih Liao, Yu-Tai Chien, Yu-Jen Chen, Hsiao-Fang Hsiung, Hsiao-Jung Chen, Meng-Hua Hsieh, Wen-Jie Wu. Originally published in JMIR Mhealth and Uhealth (http://mhealth.jmir.org), 25.05.2017.

Performance characterization of a combined material identification and screening algorithm

NASA Astrophysics Data System (ADS)

Green, Robert L.; Hargreaves, Michael D.; Gardner, Craig M.

2013-05-01

Portable analytical devices based on a gamut of technologies (Infrared, Raman, X-Ray Fluorescence, Mass Spectrometry, etc.) are now widely available. These tools have seen increasing adoption for field-based assessment by diverse users including military, emergency response, and law enforcement. Frequently, end-users of portable devices are non-scientists who rely on embedded software and the associated algorithms to convert collected data into actionable information. Two classes of problems commonly encountered in field applications are identification and screening. Identification algorithms are designed to scour a library of known materials and determine whether the unknown measurement is consistent with a stored response (or combination of stored responses). Such algorithms can be used to identify a material from many thousands of possible candidates. Screening algorithms evaluate whether at least a subset of features in an unknown measurement correspond to one or more specific substances of interest and are typically configured to detect from a small list potential target analytes. Thus, screening algorithms are much less broadly applicable than identification algorithms; however, they typically provide higher detection rates which makes them attractive for specific applications such as chemical warfare agent or narcotics detection. This paper will present an overview and performance characterization of a combined identification/screening algorithm that has recently been developed. It will be shown that the combined algorithm provides enhanced detection capability more typical of screening algorithms while maintaining a broad identification capability. Additionally, we will highlight how this approach can enable users to incorporate situational awareness during a response.

Product information representation for feature conversion and implementation of group technology automated coding

NASA Astrophysics Data System (ADS)

Medland, A. J.; Zhu, Guowang; Gao, Jian; Sun, Jian

1996-03-01

Feature conversion, also called feature transformation and feature mapping, is defined as the process of converting features from one view of an object to another view of the object. In a relatively simple implementation, for each application the design features are automatically converted into features specific for that application. All modifications have to be made via the design features. This is the approach that has attracted most attention until now. In the ideal situation, however, conversions directly from application views to the design view, and to other applications views, are also possible. In this paper, some difficulties faced in feature conversion are discussed. A new representation scheme of feature-based parts models has been proposed for the purpose of one-way feature conversion. The parts models consist of five different levels of abstraction, extending from an assembly level and its attributes, single parts and their attributes, single features and their attributes, one containing the geometric reference element and finally one for detailed geometry. One implementation of feature conversion for rotational components within GT (Group Technology) has already been undertaken using an automated coding procedure operating on a design-feature database. This database has been generated by a feature-based design system, and the GT coding scheme used in this paper is a specific scheme created for a textile machine manufacturing plant. Such feature conversion techniques presented here are only in their early stages of development and further research is underway.

Managing and Communicating Operational Workflow: Designing and Implementing an Electronic Outpatient Whiteboard.

PubMed

Steitz, Bryan D; Weinberg, Stuart T; Danciu, Ioana; Unertl, Kim M

2016-01-01

Healthcare team members in emergency department contexts have used electronic whiteboard solutions to help manage operational workflow for many years. Ambulatory clinic settings have highly complex operational workflow, but are still limited in electronic assistance to communicate and coordinate work activities. To describe and discuss the design, implementation, use, and ongoing evolution of a coordination and collaboration tool supporting ambulatory clinic operational workflow at Vanderbilt University Medical Center (VUMC). The outpatient whiteboard tool was initially designed to support healthcare work related to an electronic chemotherapy order-entry application. After a highly successful initial implementation in an oncology context, a high demand emerged across the organization for the outpatient whiteboard implementation. Over the past 10 years, developers have followed an iterative user-centered design process to evolve the tool. The electronic outpatient whiteboard system supports 194 separate whiteboards and is accessed by over 2800 distinct users on a typical day. Clinics can configure their whiteboards to support unique workflow elements. Since initial release, features such as immunization clinical decision support have been integrated into the system, based on requests from end users. The success of the electronic outpatient whiteboard demonstrates the usefulness of an operational workflow tool within the ambulatory clinic setting. Operational workflow tools can play a significant role in supporting coordination, collaboration, and teamwork in ambulatory healthcare settings.

Automated Extraction of Flow Features

NASA Technical Reports Server (NTRS)

Dorney, Suzanne (Technical Monitor); Haimes, Robert

2005-01-01

Computational Fluid Dynamics (CFD) simulations are routinely performed as part of the design process of most fluid handling devices. In order to efficiently and effectively use the results of a CFD simulation, visualization tools are often used. These tools are used in all stages of the CFD simulation including pre-processing, interim-processing, and post-processing, to interpret the results. Each of these stages requires visualization tools that allow one to examine the geometry of the device, as well as the partial or final results of the simulation. An engineer will typically generate a series of contour and vector plots to better understand the physics of how the fluid is interacting with the physical device. Of particular interest are detecting features such as shocks, re-circulation zones, and vortices (which will highlight areas of stress and loss). As the demand for CFD analyses continues to increase the need for automated feature extraction capabilities has become vital. In the past, feature extraction and identification were interesting concepts, but not required in understanding the physics of a steady flow field. This is because the results of the more traditional tools like; isc-surface, cuts and streamlines, were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of a great deal of interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one "snapshot" of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for co-processing environments). Methods must be developed to abstract the feature of interest and display it in a manner that physically makes sense.

Automated Extraction of Flow Features

NASA Technical Reports Server (NTRS)

Dorney, Suzanne (Technical Monitor); Haimes, Robert

2004-01-01

Computational Fluid Dynamics (CFD) simulations are routinely performed as part of the design process of most fluid handling devices. In order to efficiently and effectively use the results of a CFD simulation, visualization tools are often used. These tools are used in all stages of the CFD simulation including pre-processing, interim-processing, and post-processing, to interpret the results. Each of these stages requires visualization tools that allow one to examine the geometry of the device, as well as the partial or final results of the simulation. An engineer will typically generate a series of contour and vector plots to better understand the physics of how the fluid is interacting with the physical device. Of particular interest are detecting features such as shocks, recirculation zones, and vortices (which will highlight areas of stress and loss). As the demand for CFD analyses continues to increase the need for automated feature extraction capabilities has become vital. In the past, feature extraction and identification were interesting concepts, but not required in understanding the physics of a steady flow field. This is because the results of the more traditional tools like; iso-surface, cuts and streamlines, were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of a great deal of interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one "snapshot" of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for (co-processing environments). Methods must be developed to abstract the feature of interest and display it in a manner that physically makes sense.

Lithostratigraphy and shear-wave velocity in the crystallized Topopah Spring Tuff, Yucca Mountain, Nevada

USGS Publications Warehouse

Buesch, D.C.; Stokoe, K.H.; Won, K.C.; Seong, Y.J.; Jung, J.L.; Schuhen, M.D.

2006-01-01

Evaluation of the potential future response to seismic events of the proposed spent nuclear fuel and high-level radioactive waste repository at Yucca Mountain, Nevada, is in part based on the seismic properties of the host rock, the 12.8-million-year-old Topopah Spring Tuff. Because of the processes that formed the tuff, the densely welded and crystallized part has three lithophysal and three nonlithophysal zones, and each zone has characteristic variations in lithostratigraphic features and structures of the rocks. Lithostratigraphic features include lithophysal cavities; rims on lithophysae and some fractures; spots (which are similar to rims but without an associated cavity or aperture); amounts of porosity resulting from welding, crystallization, and vapor-phase corrosion and mineralization; and fractures. Seismic properties, including shear-wave velocity (Vs), have been measured on 38 pieces of core, and there is a good "first order" correlation with the lithostratigraphic zones; for example, samples from nonlithophysal zones have larger Vs values compared to samples from lithophysal zones. Some samples have Vs values that are outside the typical range for the lithostratigraphic zone; however, these samples typically have one or more fractures, "large" lithophysal cavities, or "missing pieces" relative to the sample size. Shear-wave velocity data measured in the tunnels have similar relations to lithophysal and nonlithophysal rocks; however, tunnel-based values are typically smaller than those measured in core resulting from increased lithophysae and fracturing effects. Variations in seismic properties such as Vs data from small-scale samples (typical and "flawed" core) to larger scale transects in the tunnels provide a basis for merging our understanding of the distributions of lithostratigraphic features (and zones) with a method to scale seismic properties.

Endemic chronic kidney disease of unknown etiology in Sri Lanka: Correlation of pathology with clinical stages.

PubMed

Wijetunge, S; Ratnatunga, N V I; Abeysekera, T D J; Wazil, A W M; Selvarajah, M

2015-01-01

Chronic kidney disease of unknown etiology (CKDU) is endemic among the rural farming communities in several localities in and around the North Central region of Sri Lanka. This is an interstitial type renal disease and typically has an insidious onset and slow progression. This study was conducted to identify the pathological features in the different clinical stages of CKDU. This is a retrospective study of 251 renal biopsies identified to have a primary interstitial disease from regions endemic for CKDU. Pathological features were assessed and graded in relation to the clinical stage. The mean age of those affected by endemic CKDU was 37.3 ± 12.5 years and the male to female ratio was 3.3:1. The predominant feature of stage I disease was mild and moderate interstitial fibrosis; most did not have interstitial inflammation. The typical stage II disease had moderate interstitial fibrosis with or without mild interstitial inflammation. Stage III disease had moderate and severe interstitial fibrosis, moderate interstitial inflammation, tubular atrophy and some glomerulosclerosis. Stage IV disease typically had severe interstitial fibrosis and inflammation, tubular atrophy and glomerulosclerosis. The mean age of patients with stage I disease (27 ± 10.8 years) was significantly lower than those of the other stages. About 79.2%, 55%, 49.1% and 50% in stage I, II, III and IV disease respectively were asymptomatic at the time of biopsy.

Non-linear dynamics and alternating 'flip' solutions in ferrofluidic Taylor-Couette flow

NASA Astrophysics Data System (ADS)

Altmeyer, Sebastian

2018-04-01

This study treats with the influence of a symmetry-breaking transversal magnetic field on the nonlinear dynamics of ferrofluidic Taylor-Couette flow - flow confined between two concentric independently rotating cylinders. We detected alternating 'flip' solutions which are flow states featuring typical characteristics of slow-fast-dynamics in dynamical systems. The flip corresponds to a temporal change in the axial wavenumber and we find them to appear either as pure 2-fold axisymmetric (due to the symmetry-breaking nature of the applied transversal magnetic field) or involving non-axisymmetric, helical modes in its interim solution. The latter ones show features of typical ribbon solutions. In any case the flip solutions have a preferential first axial wavenumber which corresponds to the more stable state (slow dynamics) and second axial wavenumber, corresponding to the short appearing more unstable state (fast dynamics). However, in both cases the flip time grows exponential with increasing the magnetic field strength before the flip solutions, living on 2-tori invariant manifolds, cease to exist, with lifetime going to infinity. Further we show that ferrofluidic flow turbulence differ from the classical, ordinary (usually at high Reynolds number) turbulence. The applied magnetic field hinders the free motion of ferrofluid partials and therefore smoothen typical turbulent quantities and features so that speaking of mildly chaotic dynamics seems to be a more appropriate expression for the observed motion.

Clinicopathological features of pulmonary cryptococcosis with cryptococcal titan cells: a comparative analysis of 27 cases.

PubMed

Wang, Jing-Mei; Zhou, Qiang; Cai, Hou-Rong; Zhuang, Yi; Zhang, Yi-Fen; Xin, Xiao-Yan; Meng, Fan-Qing; Wang, Ya-Ping

2014-01-01

In addition to the typical size, Cryptococcus neoformans can enlarge its size to form titan cells during infection, and its diameter can reach up to 100 μm. Clinical reports about cryptococcal titan cells are rare. Most studies focus on aspects of animal models of infection with titan cells. Herein, we report the clinical and imaging characteristics and histopathologic features of 3 patients with titan cells and 27 patients with pathogens of typical size, and describe the morphological characteristics of titan cells in details. Histologically, 3 patients with titan cells show necrosis, fibrosis and macrophage accumulation. The titan cells appear in necrotic tissue and between macrophages, and have thick wall with unstained halo around them and diameters range from 20 to 80 μm with characteristic of narrow-necked single budding. There are also organisms with typical size. All 27 patients with normal pathogens show epithelioid granulomatous lesions. There is no significantly difference in clinical and imaging feature between the two groups. Cryptococcus neoformans exhibits a striking morphological change for the formation of titan cells during pulmonary infection, which will result in misdiagnosis and under diagnosis. The histopathological changes may be new manifestation, which need to be further confirmed by the study with animal models of infection and the observation of more clinical cases. Careful observation of the tissue sections is necessary.

Corticobasal degeneration with olivopontocerebellar atrophy and TDP-43 pathology: an unusual clinicopathologic variant of CBD

PubMed Central

Kouri, Naomi; Oshima, Kenichi; Takahashi, Makio; Murray, Melissa E.; Ahmed, Zeshan; Parisi, Joseph E.; Yen, Shu-Hui C.; Dickson, Dennis W.

2013-01-01

CBD is a disorder affecting cognition and movement due to a progressive neurodegeneration associated with distinctive neuropathologic features, including abnormal phosphorylated tau protein in neurons and glia in cortex, basal ganglia, diencephalon and brainstem, as well as ballooned neurons and astrocytic plaques. We identified three cases of CBD with olivopontocerebellar atrophy (CBD-OPCA) that did not have α-synuclein-positive glial cytoplasmic inclusions of multiple system atrophy (MSA). Two patients had clinical features suggestive of progressive supranuclear palsy (PSP), and the third case had cerebellar ataxia thought to be due to idiopathic OPCA. Neuropathologic features of CBD-OPCA are compared to typical CBD, as well as MSA and PSP. CBD-OPCA and MSA had marked neuronal loss in pontine nuclei, inferior olivary nucleus, and Purkinje cell layer. Neuronal loss and grumose degeneration in the cerebellar dentate nucleus was comparable in CBD-OPCA and PSP. Image analysis of tau pathology showed greater infratentorial tau burden, especially in pontine base, in CBD-OPCA compared with typical CBD. Additionally, CBD-OPCA had TDP-43 immunoreactive neuronal and glial cytoplasmic inclusions and threads throughout the basal ganglia and in olivopontocerebellar system. CBD-OPCA met neuropathologic research diagnostic criteria for CBD and shared tau biochemical characteristics with typical CBD. These results suggest that CBD-OPCA is a distinct clinicopathologic variant of CBD with olivopontocerebellar TDP-43 pathology. PMID:23371366

Corticobasal degeneration with olivopontocerebellar atrophy and TDP-43 pathology: an unusual clinicopathologic variant of CBD.

PubMed

Kouri, Naomi; Oshima, Kenichi; Takahashi, Makio; Murray, Melissa E; Ahmed, Zeshan; Parisi, Joseph E; Yen, Shu-Hui C; Dickson, Dennis W

2013-05-01

Corticobasal degeneration (CBD) is a disorder affecting cognition and movement due to a progressive neurodegeneration associated with distinctive neuropathologic features, including abnormal phosphorylated tau protein in neurons and glia in cortex, basal ganglia, diencephalon, and brainstem, as well as ballooned neurons and astrocytic plaques. We identified three cases of CBD with olivopontocerebellar atrophy (CBD-OPCA) that did not have α-synuclein-positive glial cytoplasmic inclusions of multiple system atrophy (MSA). Two patients had clinical features suggestive of progressive supranuclear palsy (PSP), and the third case had cerebellar ataxia thought to be due to idiopathic OPCA. Neuropathologic features of CBD-OPCA are compared to typical CBD, as well as MSA and PSP. CBD-OPCA and MSA had marked neuronal loss in pontine nuclei, inferior olivary nucleus, and Purkinje cell layer. Neuronal loss and grumose degeneration in the cerebellar dentate nucleus were comparable in CBD-OPCA and PSP. Image analysis of tau pathology showed greater infratentorial tau burden, especially in pontine base, in CBD-OPCA compared with typical CBD. In addition, CBD-OPCA had TDP-43 immunoreactive neuronal and glial cytoplasmic inclusions and threads throughout the basal ganglia and in olivopontocerebellar system. CBD-OPCA met neuropathologic research diagnostic criteria for CBD and shared tau biochemical characteristics with typical CBD. These results suggest that CBD-OPCA is a distinct clinicopathologic variant of CBD with olivopontocerebellar TDP-43 pathology.

Novel Circuits for Energizing Manganin Stress Gauges

NASA Astrophysics Data System (ADS)

Tasker, Douglas

2015-06-01

This paper describes the design, manufacture and testing of novel MOSFET pulsed constant current supplies for low impedance Manganin stress gauges. The design emphasis has been on high accuracy, low noise, simple, low cost, disposable supplies that can be used to energize multiple gauges in explosive or shock experiments. Manganin gauges used to measure stresses in detonating explosive experiments have typical resistances of 50 m Ω and are energized with pulsed currents of 50 A. Conventional pulsed current supplies for these gauges are high voltage devices with outputs as high as 500 V. Common problems with the use of high voltage supplies at explosive firing sites are: erroneous signals caused by ground loops; overdrive of oscilloscopes on gauge failure; gauge signal crosstalk; cost; and errors due to finite and changing source impedances. To correct these issues a novel MOSFET circuit was designed and will be described. It is an 18-V circuit, powered by 9-V alkaline batteries, and features an optically isolated trigger, and single-point grounding. These circuits have been successfully tested at the Los Alamos National Laboratory and selected explosive tests will be described together with their results. LA-UR-15-20613.

Gamification of Cognitive Assessment and Cognitive Training: A Systematic Review of Applications and Efficacy

PubMed Central

Edwards, Elizabeth A; Lawrence, Natalia S; Coyle, David; Munafò, Marcus R

2016-01-01

Background Cognitive tasks are typically viewed as effortful, frustrating, and repetitive, which often leads to participant disengagement. This, in turn, may negatively impact data quality and/or reduce intervention effects. However, gamification may provide a possible solution. If game design features can be incorporated into cognitive tasks without undermining their scientific value, then data quality, intervention effects, and participant engagement may be improved. Objectives This systematic review aims to explore and evaluate the ways in which gamification has already been used for cognitive training and assessment purposes. We hope to answer 3 questions: (1) Why have researchers opted to use gamification? (2) What domains has gamification been applied in? (3) How successful has gamification been in cognitive research thus far? Methods We systematically searched several Web-based databases, searching the titles, abstracts, and keywords of database entries using the search strategy (gamif* OR game OR games) AND (cognit* OR engag* OR behavi* OR health* OR attention OR motiv*). Searches included papers published in English between January 2007 and October 2015. Results Our review identified 33 relevant studies, covering 31 gamified cognitive tasks used across a range of disorders and cognitive domains. We identified 7 reasons for researchers opting to gamify their cognitive training and testing. We found that working memory and general executive functions were common targets for both gamified assessment and training. Gamified tests were typically validated successfully, although mixed-domain measurement was a problem. Gamified training appears to be highly engaging and does boost participant motivation, but mixed effects of gamification on task performance were reported. Conclusions Heterogeneous study designs and typically small sample sizes highlight the need for further research in both gamified training and testing. Nevertheless, careful application of gamification can provide a way to develop engaging and yet scientifically valid cognitive assessments, and it is likely worthwhile to continue to develop gamified cognitive tasks in the future. PMID:27421244

Gamification of Cognitive Assessment and Cognitive Training: A Systematic Review of Applications and Efficacy.

PubMed

Lumsden, Jim; Edwards, Elizabeth A; Lawrence, Natalia S; Coyle, David; Munafò, Marcus R

2016-07-15

Cognitive tasks are typically viewed as effortful, frustrating, and repetitive, which often leads to participant disengagement. This, in turn, may negatively impact data quality and/or reduce intervention effects. However, gamification may provide a possible solution. If game design features can be incorporated into cognitive tasks without undermining their scientific value, then data quality, intervention effects, and participant engagement may be improved. This systematic review aims to explore and evaluate the ways in which gamification has already been used for cognitive training and assessment purposes. We hope to answer 3 questions: (1) Why have researchers opted to use gamification? (2) What domains has gamification been applied in? (3) How successful has gamification been in cognitive research thus far? We systematically searched several Web-based databases, searching the titles, abstracts, and keywords of database entries using the search strategy (gamif* OR game OR games) AND (cognit* OR engag* OR behavi* OR health* OR attention OR motiv*). Searches included papers published in English between January 2007 and October 2015. Our review identified 33 relevant studies, covering 31 gamified cognitive tasks used across a range of disorders and cognitive domains. We identified 7 reasons for researchers opting to gamify their cognitive training and testing. We found that working memory and general executive functions were common targets for both gamified assessment and training. Gamified tests were typically validated successfully, although mixed-domain measurement was a problem. Gamified training appears to be highly engaging and does boost participant motivation, but mixed effects of gamification on task performance were reported. Heterogeneous study designs and typically small sample sizes highlight the need for further research in both gamified training and testing. Nevertheless, careful application of gamification can provide a way to develop engaging and yet scientifically valid cognitive assessments, and it is likely worthwhile to continue to develop gamified cognitive tasks in the future.

Proposed new accelerator design for homeland security x-ray applications

DOE PAGES

Clayton, James; Shedlock, Daniel; Langeveld, Willem G.J.; ...

2015-01-01

Two goals for security scanning of cargo and freight are the ability to determine the type of material that is being imaged, and to do so at low radiation dose. One commonly used technique to determine the effective Z of the cargo is dual-energy imaging, i.e. imaging with different x-ray energy spectra. Another technique uses the fact that the transmitted x-ray spectrum itself also depends on the effective Z. Spectroscopy is difficult because the energy of individual x rays needs to be measured in a very high count-rate environment. Typical accelerators for security applications offer large but short bursts ofmore » x-rays, suitable for current-mode integrated imaging. In order to perform x-ray spectroscopy, a new accelerator design is desired that has the following features: 1) increased duty factor in order to spread out the arrival of x-rays at the detector array over time; 2) x-ray intensity modulation from one delivered pulse to the next by adjusting the accelerator electron beam instantaneous current so as to deliver adequate signal without saturating the spectroscopic detector; and 3) the capability to direct the (forward peaked) x-ray intensity towards high-attenuation areas in the cargo (“fan-beam-steering”). Current sources are capable of 0.1% duty factor, although usually they are operated at significantly lower duty factors (~0.04%), but duty factors in the range 0.4-1.0% are desired. The higher duty factor can be accomplished, e.g., by moving from 300 pulses per second (pps) to 1000 pps and/or increasing the pulse duration from a typical 4 μs to 10 μs. This paper describes initial R&D to examine cost effective modifications that could be performed on a typical accelerator for these purposes, as well as R&D for fan-beam steering.« less

Comparison of Endoscopic and Histological Findings between Typical and Atypical Celiac Disease in Children.

PubMed

Semwal, Pooja; Gupta, Raj Kumar; Sharma, Rahul; Garg, Kapil

2018-04-01

Celiac disease is a common non-communicable disease with varied presentations. Purpose of this study was to find the duodeno-endoscopic features in celiac disease and to compare duodeno-endoscopic and histological findings between typical and atypical celiac disease in children. Hospital based observational study was conducted at Sir Padampat Mother and Child Health Institute, Jaipur from June 2015 to May 2016. Patients were selected and divided in two groups- typical and atypical celiac disease based upon the presenting symptoms. Upper gastrointestinal endoscopy and duodenal biopsy was performed for serology positive patients. Results were analysed using appropriate statistical test of significance. Out of 101 enrolled patients, 47.5% were male. Age ranged from 1 to 18 years. Study showed that 54.5% were typical and 45.5% were atypical. Patients presenting with atypical symptoms were predominantly of older age group. On endoscopy, scalloping, mosaic pattern, reduced fold height and absent fold height; and in histology, advanced Marsh stage were significantly higher in the typical group. Awareness of atypical presentations as well as duodeno-endoscopic features may have considerable practical importance for the diagnosis of celiac disease in children. Scalloping, mosaic pattern, reduced fold height and nodularity are main endoscopic markers of celiac disease in children. Endoscopic markers of duodenal mucosa may be important in early diagnosis of celiac disease, in children subjected to endoscopy for atypical presentations or indication other than suspected celiac disease.

Changing facial phenotype in Cohen syndrome: towards clues for an earlier diagnosis.

PubMed

El Chehadeh-Djebbar, Salima; Blair, Edward; Holder-Espinasse, Muriel; Moncla, Anne; Frances, Anne-Marie; Rio, Marlène; Debray, François-Guillaume; Rump, Patrick; Masurel-Paulet, Alice; Gigot, Nadège; Callier, Patrick; Duplomb, Laurence; Aral, Bernard; Huet, Frédéric; Thauvin-Robinet, Christel; Faivre, Laurence

2013-07-01

Cohen syndrome (CS) is a rare autosomal recessive condition caused by mutations and/or large rearrangements in the VPS13B gene. CS clinical features, including developmental delay, the typical facial gestalt, chorioretinal dystrophy (CRD) and neutropenia, are well described. CS diagnosis is generally raised after school age, when visual disturbances lead to CRD diagnosis and to VPS13B gene testing. This relatively late diagnosis precludes accurate genetic counselling. The aim of this study was to analyse the evolution of CS facial features in the early period of life, particularly before school age (6 years), to find clues for an earlier diagnosis. Photographs of 17 patients with molecularly confirmed CS were analysed, from birth to preschool age. By comparing their facial phenotype when growing, we show that there are no special facial characteristics before 1 year. However, between 2 and 6 years, CS children already share common facial features such as a short neck, a square face with micrognathia and full cheeks, a hypotonic facial appearance, epicanthic folds, long ears with an everted upper part of the auricle and/or a prominent lobe, a relatively short philtrum, a small and open mouth with downturned corners, a thick lower lip and abnormal eye shapes. These early transient facial features evolve to typical CS facial features with aging. These observations emphasize the importance of ophthalmological tests and neutrophil count in children in preschool age presenting with developmental delay, hypotonia and the facial features we described here, for an earlier CS diagnosis.

Spacecraft high-voltage power supply construction

NASA Technical Reports Server (NTRS)

Sutton, J. F.; Stern, J. E.

1975-01-01

The design techniques, circuit components, fabrication techniques, and past experience used in successful high-voltage power supplies for spacecraft flight systems are described. A discussion of the basic physics of electrical discharges in gases is included and a design rationale for the prevention of electrical discharges is provided. Also included are typical examples of proven spacecraft high-voltage power supplies with typical specifications for design, fabrication, and testing.

Multi-Modal Curriculum Learning for Semi-Supervised Image Classification.

PubMed

Gong, Chen; Tao, Dacheng; Maybank, Stephen J; Liu, Wei; Kang, Guoliang; Yang, Jie

2016-07-01

Semi-supervised image classification aims to classify a large quantity of unlabeled images by typically harnessing scarce labeled images. Existing semi-supervised methods often suffer from inadequate classification accuracy when encountering difficult yet critical images, such as outliers, because they treat all unlabeled images equally and conduct classifications in an imperfectly ordered sequence. In this paper, we employ the curriculum learning methodology by investigating the difficulty of classifying every unlabeled image. The reliability and the discriminability of these unlabeled images are particularly investigated for evaluating their difficulty. As a result, an optimized image sequence is generated during the iterative propagations, and the unlabeled images are logically classified from simple to difficult. Furthermore, since images are usually characterized by multiple visual feature descriptors, we associate each kind of features with a teacher, and design a multi-modal curriculum learning (MMCL) strategy to integrate the information from different feature modalities. In each propagation, each teacher analyzes the difficulties of the currently unlabeled images from its own modality viewpoint. A consensus is subsequently reached among all the teachers, determining the currently simplest images (i.e., a curriculum), which are to be reliably classified by the multi-modal learner. This well-organized propagation process leveraging multiple teachers and one learner enables our MMCL to outperform five state-of-the-art methods on eight popular image data sets.

How tufted capuchin monkeys (Cebus apella spp) and common chimpanzees (Pan troglodytes) align objects to surfaces: Insights into spatial reasoning and implications for tool use

PubMed Central

Fragaszy, Dorothy M.; Stone, Brian; Scott, Nicole M.; Menzel, Charles

2011-01-01

This report addresses phylogenetic variation in a spatial skill that underlies tool use: aligning objects to a feature of a surface. Fragaszy and Cummins-Sebree’s [2005] model of relational spatial reasoning and Skill Development and Perception-Action theories guided the design of the study. We examined how capuchins and chimpanzees place stick objects of varying shapes into matching grooves on a flat surface. Although most individuals aligned the long axis of the object with the matching groove more often than expected by chance, all typically did so with poor precision. Some individuals managed to align a second feature, and only one (a capuchin monkey) achieved above-chance success at aligning three features with matching grooves. Our findings suggest that capuchins and chimpanzees do not reliably align objects along even one axis, and that neither species can reliably or easily master object placement tasks that require managing two or more spatial relations concurrently. Moreover, they did not systematically vary their behavior in a manner that would aid discovery of the affordances of the stick-surface combination beyond sliding the stick along the surface (which may have provided haptic information about the location of the groove). These limitations have profound consequences for the forms of tool use we can expect these individuals to master. PMID:21608008

Reducing Field Distortion in Magnetic Resonance Imaging

NASA Technical Reports Server (NTRS)

Eom, Byeong Ho; Penanen, Konstantin; Hahn, Inseob

2010-01-01

A concept for a magnetic resonance imaging (MRI) system that would utilize a relatively weak magnetic field provides for several design features that differ significantly from the corresponding features of conventional MRI systems. Notable among these features are a magnetic-field configuration that reduces (relative to the conventional configuration) distortion and blurring of the image, the use of a superconducting quantum interference device (SQUID) magnetometer as the detector, and an imaging procedure suited for the unconventional field configuration and sensor. In a typical application of MRI, a radio-frequency pulse is used to excite precession of the magnetic moments of protons in an applied magnetic field, and the decaying precession is detected for a short time following the pulse. The precession occurs at a resonance frequency proportional to the strengths of the magnetic field and the proton magnetic moment. The magnetic field is configured to vary with position in a known way; hence, by virtue of the aforesaid proportionality, the resonance frequency varies with position in a known way. In other words, position is encoded as resonance frequency. MRI using magnetic fields weaker than those of conventional MRI offers several advantages, including cheaper and smaller equipment, greater compatibility with metallic objects, and higher image quality because of low susceptibility distortion and enhanced spin-lattice-relaxation- time contrast. SQUID MRI is being developed into a practical MRI method for applied magnetic flux densities of the order of only 100 T

Early Generalized Overgrowth in Boys With Autism

PubMed Central

Chawarska, Katarzyna; Campbell, Daniel; Chen, Lisha; Shic, Frederick; Klin, Ami; Chang, Joseph

2016-01-01

Context Multiple studies have reported an overgrowth in head circumference (HC) in the first year of life in autism. However, it is unclear whether this phenomenon is independent of overall body growth and whether it is associated with specific social or cognitive features. Objectives To examine the trajectory of early HC growth in autism compared with control groups; to assess whether HC growth in autism is independent of height and weight growth during infancy; and to examine HC growth from birth to 24 months in relationship to social, verbal, cognitive, and adaptive functioning levels. Design Retrospective study. Setting A specialized university-based clinic. Participants Boys diagnosed as having autistic disorder (n=64), pervasive developmental disorder–not otherwise specified (n=34), global developmental delay (n=13), and other developmental problems (n=18) and typically developing boys (n=55). Main Outcome Measures Age-related changes in HC, height, and weight between birth and age 24 months; measures of social, verbal, and cognitive functioning at age 2 years. Results Compared with typically developing controls, boys with autism were significantly longer by age 4.8 months, had a larger HC by age 9.5 months, and weighed more by age 11.4 months (P=.05 for all). None of the other clinical groups showed a similar overgrowth pattern. Boys with autism who were in the top 10% of overall physical size in infancy exhibited greater severity of social deficits (P=.009) and lower adaptive functioning (P=.03). Conclusions Boys with autism experienced accelerated HC growth in the first year of life. However, this phenomenon reflected a generalized process affecting other morphologic features, including height and weight. The study highlights the importance of studying factors that influence not only neuronal development but also skeletal growth in autism. PMID:21969460

Recent Changes in Pgopher: a General Purpose Program for Simulating Rotational Structure

NASA Astrophysics Data System (ADS)

Western, Colin

2010-06-01

Key features of the PGOPHER program include the simulation and fitting of the rotational structure of linear molecules and symmetric and asymmetric tops, including effects due to unpaired electrons and nuclear spin. The program is written to be as general as possible, and can handle many effects such as multiple interacting states, predissociation and multiphoton transitions. It is designed to be easy to use, with a flexible graphical user interface. PGOPHER has been released as an open source program, and can be freely downloaded from the website at http://pgopher.chm.bris.ac.uk. Recent additions include a mode which allows the calculation of vibrational energy levels starting from a harmonic model and the multidimensional Franck-Condon factors required to calculate intensities of vibronic transitions. PGOPHER takes account of both the displacement along normal co-ordinates and mixing between modes (the Duschinsky effect). l matrices produced from ab initio programs can be directly read by PGOPHER or the mode displacements and mixing can be fit to observed spectra. In addition the effects of external electric and/or magnetic fields can now be calculated, including plots of energy level against electric field suitable for predicting Stark deceleration, focussing and trapping of molecules. The figure shows a typical plot, showing the electric field tuning of the M = 0 levels of 202, 111 and 110 levels of (NO)_2. Other new features include fits to combination differences, simulation of the Doppler split peak typical of Fourier transform microwave spectroscopy, specifying a nuclear spin temperature independent of rotational temperature and interactive adjustment of parameter values with the mouse in addition to typing values.

Two cases of seborrheic keratosis with basal clear cells.

PubMed

Anan, Takashi; Fukumoto, Takaya; Kimura, Tetsunori

2017-03-01

Seborrheic keratosis with basal clear cells (SKBCC) is an extremely rare histopathological variant of seborrheic keratosis that has histological similarities to melanoma in situ. We herein report two cases of SKBCC and provide the first description of the dermoscopic features of this condition, in addition to the histopathological findings. Both of the two lesions showed typical histological architectures of seborrheic keratosis with rows or focal clusters of monomorphic clear cells with abundant pale cytoplasm and small round nucleus in the basal layer. Immunohistochemical examination revealed that most clear cells were positive for high molecular weight cytokeratin (34βE12) in a peripheral pattern but were negative tor Melan-A. Dermoscopy revealed typical features of ordinary seborrheic keratosis, while unfortunately did not reflect the presence of basal clear cells. © 2016 Japanese Dermatological Association.

Differences in manifestations of Marfan syndrome, Ehlers-Danlos syndrome, and Loeys-Dietz syndrome.

PubMed

Meester, Josephina A N; Verstraeten, Aline; Schepers, Dorien; Alaerts, Maaike; Van Laer, Lut; Loeys, Bart L

2017-11-01

Many different heritable connective tissue disorders (HCTD) have been described over the past decades. These syndromes often affect the connective tissue of various organ systems, including heart, blood vessels, skin, joints, bone, eyes, and lungs. The discovery of these HCTD was followed by the identification of mutations in a wide range of genes encoding structural proteins, modifying enzymes, or components of the TGFβ-signaling pathway. Three typical examples of HCTD are Marfan syndrome (MFS), Ehlers-Danlos syndrome (EDS), and Loeys-Dietz syndrome (LDS). These syndromes show some degree of phenotypical overlap of cardiovascular, skeletal, and cutaneous features. MFS is typically characterized by cardiovascular, ocular, and skeletal manifestations and is caused by heterozygous mutations in FBN1 , coding for the extracellular matrix (ECM) protein fibrillin-1. The most common cardiovascular phenotype involves aortic aneurysm and dissection at the sinuses of Valsalva. LDS is caused by mutations in TGBR1/2 , SMAD2/3 , or TGFB2/3 , all coding for components of the TGFβ-signaling pathway. LDS can be distinguished from MFS by the unique presence of hypertelorism, bifid uvula or cleft palate, and widespread aortic and arterial aneurysm and tortuosity. Compared to MFS, LDS cardiovascular manifestations tend to be more severe. In contrast, no association is reported between LDS and the presence of ectopia lentis, a key distinguishing feature of MFS. Overlapping features between MFS and LDS include scoliosis, pes planus, anterior chest deformity, spontaneous pneumothorax, and dural ectasia. EDS refers to a group of clinically and genetically heterogeneous connective tissue disorders and all subtypes are characterized by variable abnormalities of skin, ligaments and joints, blood vessels, and internal organs. Typical presenting features include joint hypermobility, skin hyperextensibility, and tissue fragility. Up to one quarter of the EDS patients show aortic aneurysmal disease. The latest EDS nosology distinguishes 13 subtypes. Many phenotypic features show overlap between the different subtypes, which makes the clinical diagnosis rather difficult and highlights the importance of molecular diagnostic confirmation.

Differences in manifestations of Marfan syndrome, Ehlers-Danlos syndrome, and Loeys-Dietz syndrome

PubMed Central

Meester, Josephina A. N.; Verstraeten, Aline; Schepers, Dorien; Alaerts, Maaike; Van Laer, Lut

2017-01-01

Many different heritable connective tissue disorders (HCTD) have been described over the past decades. These syndromes often affect the connective tissue of various organ systems, including heart, blood vessels, skin, joints, bone, eyes, and lungs. The discovery of these HCTD was followed by the identification of mutations in a wide range of genes encoding structural proteins, modifying enzymes, or components of the TGFβ-signaling pathway. Three typical examples of HCTD are Marfan syndrome (MFS), Ehlers-Danlos syndrome (EDS), and Loeys-Dietz syndrome (LDS). These syndromes show some degree of phenotypical overlap of cardiovascular, skeletal, and cutaneous features. MFS is typically characterized by cardiovascular, ocular, and skeletal manifestations and is caused by heterozygous mutations in FBN1, coding for the extracellular matrix (ECM) protein fibrillin-1. The most common cardiovascular phenotype involves aortic aneurysm and dissection at the sinuses of Valsalva. LDS is caused by mutations in TGBR1/2, SMAD2/3, or TGFB2/3, all coding for components of the TGFβ-signaling pathway. LDS can be distinguished from MFS by the unique presence of hypertelorism, bifid uvula or cleft palate, and widespread aortic and arterial aneurysm and tortuosity. Compared to MFS, LDS cardiovascular manifestations tend to be more severe. In contrast, no association is reported between LDS and the presence of ectopia lentis, a key distinguishing feature of MFS. Overlapping features between MFS and LDS include scoliosis, pes planus, anterior chest deformity, spontaneous pneumothorax, and dural ectasia. EDS refers to a group of clinically and genetically heterogeneous connective tissue disorders and all subtypes are characterized by variable abnormalities of skin, ligaments and joints, blood vessels, and internal organs. Typical presenting features include joint hypermobility, skin hyperextensibility, and tissue fragility. Up to one quarter of the EDS patients show aortic aneurysmal disease. The latest EDS nosology distinguishes 13 subtypes. Many phenotypic features show overlap between the different subtypes, which makes the clinical diagnosis rather difficult and highlights the importance of molecular diagnostic confirmation. PMID:29270370

Design, fabrication and acoustic tests of a 36 inch (0.914 meter) statorless turbotip fan

NASA Technical Reports Server (NTRS)

Smith, E. G.; Stempert, D. L.; Uhl, W. R.

1975-01-01

The LF336/E is a 36 inch (0.914 meter) diameter fan designed to operate in a rotor-alone configuration. Design features required for modification of the existing LF336/A rotor-stator fan into the LF336/E statorless fan configuration are discussed. Tests of the statorless fan identified an aerodynamic performance deficiency due to inaccurate accounting of the fan exit swirl during the aerodynamic design. This performance deficiency, related to fan exit static pressure levels, produced about a 20 percent thrust loss. A study was then conducted for further evaluation of the fan exit flow fields typical of statorless fan systems. This study showed that through proper selection of fan design variables such as pressure ratio, radius ratio, and swirl distributions, performance of a statorless fan configuration could be improved with levels of thrust approaching the conventional rotor-stator fan system. Acoustic measurements were taken for the statorless fan system at both GE and NASA, and when compared to other lift fan systems, showed noise levels comparable to the quietest lift fan configuration which included rotor-stator spacing and acoustic treatment. The statorless fan system was also used to determine effects of rotor leading edge serrations on noise generations. A cascade test program identified the serration geometry based on minimum pressure losses, wake turbulence levels and noise generations.

Herpes Simplex Virus Type 1 infection: overview on relevant clinico-pathological features.

PubMed

Arduino, Paolo G; Porter, Stephen R

2008-02-01

Herpes Simplex Virus Type 1 (HSV-1) is a nuclear replicating enveloped virus, usually acquired through direct contact with infected lesions or body fluids (typically saliva). The prevalence of HSV-1 infection increases progressively from childhood, the seroprevalence being inversely related to socioeconomic background. Primary HSV-1 infections in children are either asymptomatic or following an incubation period of about 1 week gives rise to mucocutaneous vesicular eruptions. Herpetic gingivostomatitis typically affects the tongue, lips, gingival, buccal mucosa and the hard and soft palate. Most primary oro-facial HSV infection is caused by HSV-1, infection by HSV-2 is increasingly common. Recurrent infections, which occur at variable intervals, typically give rise to vesiculo-ulcerative lesions at mucocutaneous junctions particularly the lips (herpes labialis). Recurrent HSV-1 infection within the mouth is uncommon in otherwise healthy patients, although in immunocompromised patients, recurrent infection can be more extensive and/or aggressive. The diagnosis of common herpetic infection can usually be based upon the clinical history and presenting features. Confirmatory laboratory diagnosis is, however, required when patients are, or may be, immunocompromised.

Heterogeneous patterns of brain atrophy in Alzheimer's disease.

PubMed

Poulakis, Konstantinos; Pereira, Joana B; Mecocci, Patrizia; Vellas, Bruno; Tsolaki, Magda; Kłoszewska, Iwona; Soininen, Hilkka; Lovestone, Simon; Simmons, Andrew; Wahlund, Lars-Olof; Westman, Eric

2018-05-01

There is increasing evidence showing that brain atrophy varies between patients with Alzheimer's disease (AD), suggesting that different anatomical patterns might exist within the same disorder. We investigated AD heterogeneity based on cortical and subcortical atrophy patterns in 299 AD subjects from 2 multicenter cohorts. Clusters of patients and important discriminative features were determined using random forest pairwise similarity, multidimensional scaling, and distance-based hierarchical clustering. We discovered 2 typical (72.2%) and 3 atypical (28.8%) subtypes with significantly different demographic, clinical, and cognitive characteristics, and different rates of cognitive decline. In contrast to previous studies, our unsupervised random forest approach based on cortical and subcortical volume measures and their linear and nonlinear interactions revealed more typical AD subtypes with important anatomically discriminative features, while the prevalence of atypical cases was lower. The hippocampal-sparing and typical AD subtypes exhibited worse clinical progression in visuospatial, memory, and executive cognitive functions. Our findings suggest there is substantial heterogeneity in AD that has an impact on how patients function and progress over time. Copyright © 2018 Elsevier Inc. All rights reserved.

Web Image Search Re-ranking with Click-based Similarity and Typicality.

PubMed

Yang, Xiaopeng; Mei, Tao; Zhang, Yong Dong; Liu, Jie; Satoh, Shin'ichi

2016-07-20

In image search re-ranking, besides the well known semantic gap, intent gap, which is the gap between the representation of users' query/demand and the real intent of the users, is becoming a major problem restricting the development of image retrieval. To reduce human effects, in this paper, we use image click-through data, which can be viewed as the "implicit feedback" from users, to help overcome the intention gap, and further improve the image search performance. Generally, the hypothesis visually similar images should be close in a ranking list and the strategy images with higher relevance should be ranked higher than others are widely accepted. To obtain satisfying search results, thus, image similarity and the level of relevance typicality are determinate factors correspondingly. However, when measuring image similarity and typicality, conventional re-ranking approaches only consider visual information and initial ranks of images, while overlooking the influence of click-through data. This paper presents a novel re-ranking approach, named spectral clustering re-ranking with click-based similarity and typicality (SCCST). First, to learn an appropriate similarity measurement, we propose click-based multi-feature similarity learning algorithm (CMSL), which conducts metric learning based on clickbased triplets selection, and integrates multiple features into a unified similarity space via multiple kernel learning. Then based on the learnt click-based image similarity measure, we conduct spectral clustering to group visually and semantically similar images into same clusters, and get the final re-rank list by calculating click-based clusters typicality and withinclusters click-based image typicality in descending order. Our experiments conducted on two real-world query-image datasets with diverse representative queries show that our proposed reranking approach can significantly improve initial search results, and outperform several existing re-ranking approaches.

Pavement design and performance studies : progress report no. 4 on phase A, performance study of typical Virginia pavements.

DOT National Transportation Integrated Search

1970-01-01

The performance of in-service typical Virginia flexible and rigid pavements in all areas of the state is under evaluation. The objectives are to provide a ready reference for designers and field engineers and to provide background information for des...

How Do Typically Developing Deaf Children and Deaf Children with Autism Spectrum Disorder Use the Face When Comprehending Emotional Facial Expressions in British Sign Language?

ERIC Educational Resources Information Center

Denmark, Tanya; Atkinson, Joanna; Campbell, Ruth; Swettenham, John

2014-01-01

Facial expressions in sign language carry a variety of communicative features. While emotion can modulate a spoken utterance through changes in intonation, duration and intensity, in sign language specific facial expressions presented concurrently with a manual sign perform this function. When deaf adult signers cannot see facial features, their…

Temporal Processing Instability with Millisecond Accuracy Is a Cardinal Feature of Sensorimotor Impairments in Autism Spectrum Disorder: Analysis Using the Synchronized Finger-Tapping Task

ERIC Educational Resources Information Center

Morimoto, Chie; Hida, Eisuke; Shima, Keisuke; Okamura, Hitoshi

2018-01-01

To identify a specific sensorimotor impairment feature of autism spectrum disorder (ASD), we focused on temporal processing with millisecond accuracy. A synchronized finger-tapping task was used to characterize temporal processing in individuals with ASD as compared to typically developing (TD) individuals. We found that individuals with ASD…

Exploring the Cognitive Features in Children with Autism Spectrum Disorder, Their Co-Twins, and Typically Developing Children within a Population-Based Sample

ERIC Educational Resources Information Center

Brunsdon, Victoria E. A.; Colvert, Emma; Ames, Catherine; Garnett, Tracy; Gillan, Nicola; Hallett, Victoria; Lietz, Stephanie; Woodhouse, Emma; Bolton, Patrick; Happé, Francesca

2015-01-01

Background: The behavioural symptoms of autism spectrum disorder (ASD) are thought to reflect underlying cognitive deficits/differences. The findings in the literature are somewhat mixed regarding the cognitive features of ASD. This study attempted to address this issue by investigating a range of cognitive deficits and the prevalence of multiple…

Analysis of behaviour patterns and thermal responses to a hot-arid climate in rural China.

PubMed

Yan, Haiyan; Yang, Liu; Zheng, Wuxing; He, Wenfang; Li, Daoyi

2016-07-01

Climate can greatly affect building design, life style and thermal perception for all groups of people; however, this phenomenon has not yet been rigorously evaluated in China's hot-arid climate. The aim of this paper is to present the results of a thermal comfort survey by evaluating the influence of the hot-arid climate upon the behavioural patterns and thermal comfort responses of 160 residents in 65 traditional vernacular houses in Turfan, China, in 2011. In this survey, there were 206 sets of effective data, and the features of the traditional residential buildings and the human behaviour patterns in Turfan were described and analysed. The results showed that the diversified courtyards and shade spaces were the most obvious features of traditional houses in Turfan. People here typically spend most of their time in one of two spaces for eating, resting, and entertaining. It was found that the preferred temperature was 26.5°C. The preferred air velocity occurred at 0.62m/s. A suitable air velocity range of 0.15-1.24m/s was suggested in Turfan. Moreover, the neutral temperature of the local people was 30.1°C (tg or to). The upper limits of the 80% acceptable zone by using the direct and indirect acceptability method were 32.7 and 33.8°C, respectively. The neutral temperature and upper limit of the acceptable zone in Turfan were higher than those of the adaptive standards. Attention should be paid to the role of thermal comfort in influencing building design by using simple passive cooling strategies. The above results are believed to be potentially valuable for the design and evaluation of residential buildings located in hot-arid climate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Teaching Introductory Geoscience: A Cutting Edge Workshop Report

NASA Astrophysics Data System (ADS)

Manduca, C.; Tewksbury, B.; Egger, A.; MacDonald, H.; Kirk, K.

2008-12-01

Introductory undergraduate courses play a pivotal role in the geosciences. They serve as recruiting grounds for majors and future professionals, provide relevant experiences in geoscience for pre-service teachers, and offer opportunities to influence future policy makers, business people, professionals, and citizens. An introductory course is also typically the only course in geoscience that most of our students will ever take. Because the role of introductory courses is pivotal in geoscience education, a workshop on Teaching Introductory Courses in the 21st Century was held in July 2008 as part of the On the Cutting Edge faculty development program. A website was also developed in conjunction with the workshop. One of the central themes of the workshop was the importance of considering the long-term impact a course should have on students. Ideally, courses can be designed with this impact in mind. Approaches include using the local geology to focus the course and illustrate concepts; designing a course for particular audience (such as Geology for Engineers); creating course features that help students understand and interpret geoscience in the news; and developing capstone projects to teach critical thinking and problem solving skills in a geologic context. Workshop participants also explored strategies for designing engaging activities including exploring with Google Earth, using real-world scenarios, connecting with popular media, or making use of campus features on local field trips. In addition, introductory courses can emphasize broad skills such as teaching the process of science, using quantitative reasoning and developing communication skills. Materials from the workshop as well as descriptions of more than 150 introductory courses and 350 introductory-level activities are available on the website: http://serc.carleton.edu/NAGTWorkshops/intro/index.html.

Examination of How and Why Over-the-Bed Tables Are Used: Use Cases and Needs from Healthcare Providers.

PubMed

Manganelli, Joe; Threatt, Anthony; Brooks, Johnell O; Healy, Stan; Merino, Jessica; Yanik, Paul; Walker, Ian; Green, Keith

2014-01-01

This article presents the results of an exploratory study in which 14 clinical and staff subject matter experts (SMEs) at a regional rehabilitation hospital were interviewed in order to understand how and why over-the-bed tables are used. It is important to understand how and why a device or environment is used when designing it, and not just what features and functions are preferred. This knowledge is valuable both for contextualizing user feature and function preferences and for characterizing and prioritizing design challenges and opportunities. Fourteen hospital clinical and support staff subject-matter experts participated in semi-structured interviews with scenario enactments in a medium-fidelity, full-scale mock-up of a typical patient room. During these interviews, they interacted with two personas played by actors and were asked to enact an example of a normal visit, from entering the room through treatment/service and then exiting. Data were analyzed via methodological triangulation including frequency analysis, content analysis, and affinity diagramming. The results include a use-case analysis with illustrative sketches, a list of needs statements, and final observations. Successfully using the over-the-bed table is dependent upon proper positioning, especially in bed during meals. There are fewer problems associated with over-the-bed table use while seated in a chair than when in the bed. The over-the-bed table is a key component in acute care, inpatient therapies. Clinicians are generally open to "smart" furniture in the patient room but question its cost-effectiveness, robustness, and flexibility. Evidence-based design, human factors, patient-centered care, quality care, technology.

Technical Note: Rod phantom analysis for comparison of PET detector sampling and reconstruction methods.

PubMed

Wollenweber, Scott D; Kemp, Brad J

2016-11-01

This investigation aimed to develop a scanner quantification performance methodology and compare multiple metrics between two scanners under different imaging conditions. Most PET scanners are designed to work over a wide dynamic range of patient imaging conditions. Clinical constraints, however, often impact the realization of the entitlement performance for a particular scanner design. Using less injected dose and imaging for a shorter time are often key considerations, all while maintaining "acceptable" image quality and quantitative capability. A dual phantom measurement including resolution inserts was used to measure the effects of in-plane (x, y) and axial (z) system resolution between two PET/CT systems with different block detector crystal dimensions. One of the scanners had significantly thinner slices. Several quantitative measures, including feature contrast recovery, max/min value, and feature profile accuracy were derived from the resulting data and compared between the two scanners and multiple phantoms and alignments. At the clinically relevant count levels used, the scanner with thinner slices had improved performance of approximately 2%, averaged over phantom alignments, measures, and reconstruction methods, for the head-sized phantom, mainly demonstrated with the rods aligned perpendicular to the scanner axis. That same scanner had a slightly decreased performance of -1% for the larger body-size phantom, mostly due to an apparent noise increase in the images. Most of the differences in the metrics between the two scanners were less than 10%. Using the proposed scanner performance methodology, it was shown that smaller detector elements and a larger number of image voxels require higher count density in order to demonstrate improved image quality and quantitation. In a body imaging scenario under typical clinical conditions, the potential advantages of the design must overcome increases in noise due to lower count density.

Electronic camera-management system for 35-mm and 70-mm film cameras

NASA Astrophysics Data System (ADS)

Nielsen, Allan

1993-01-01

Military and commercial test facilities have been tasked with the need for increasingly sophisticated data collection and data reduction. A state-of-the-art electronic control system for high speed 35 mm and 70 mm film cameras designed to meet these tasks is described. Data collection in today's test range environment is difficult at best. The need for a completely integrated image and data collection system is mandated by the increasingly complex test environment. Instrumentation film cameras have been used on test ranges to capture images for decades. Their high frame rates coupled with exceptionally high resolution make them an essential part of any test system. In addition to documenting test events, today's camera system is required to perform many additional tasks. Data reduction to establish TSPI (time- space-position information) may be performed after a mission and is subject to all of the variables present in documenting the mission. A typical scenario would consist of multiple cameras located on tracking mounts capturing the event along with azimuth and elevation position data. Corrected data can then be reduced using each camera's time and position deltas and calculating the TSPI of the object using triangulation. An electronic camera control system designed to meet these requirements has been developed by Photo-Sonics, Inc. The feedback received from test technicians at range facilities throughout the world led Photo-Sonics to design the features of this control system. These prominent new features include: a comprehensive safety management system, full local or remote operation, frame rate accuracy of less than 0.005 percent, and phase locking capability to Irig-B. In fact, Irig-B phase lock operation of multiple cameras can reduce the time-distance delta of a test object traveling at mach-1 to less than one inch during data reduction.

Distilling the essential features of a protein surface for improving protein-ligand docking, scoring, and virtual screening

NASA Astrophysics Data System (ADS)

Zavodszky, Maria I.; Sanschagrin, Paul C.; Kuhn, Leslie A.; Korde, Rajesh S.

2002-12-01

For the successful identification and docking of new ligands to a protein target by virtual screening, the essential features of the protein and ligand surfaces must be captured and distilled in an efficient representation. Since the running time for docking increases exponentially with the number of points representing the protein and each ligand candidate, it is important to place these points where the best interactions can be made between the protein and the ligand. This definition of favorable points of interaction can also guide protein structure-based ligand design, which typically focuses on which chemical groups provide the most energetically favorable contacts. In this paper, we present an alternative method of protein template and ligand interaction point design that identifies the most favorable points for making hydrophobic and hydrogen-bond interactions by using a knowledge base. The knowledge-based protein and ligand representations have been incorporated in version 2.0 of SLIDE and resulted in dockings closer to the crystal structure orientations when screening a set of 57 known thrombin and glutathione S-transferase (GST) ligands against the apo structures of these proteins. There was also improved scoring enrichment of the dockings, meaning better differentiation between the chemically diverse known ligands and a ˜15,000-molecule dataset of randomly-chosen small organic molecules. This approach for identifying the most important points of interaction between proteins and their ligands can equally well be used in other docking and design techniques. While much recent effort has focused on improving scoring functions for protein-ligand docking, our results indicate that improving the representation of the chemistry of proteins and their ligands is another avenue that can lead to significant improvements in the identification, docking, and scoring of ligands.

Comparison of Topographic Profiles Across Venus' Coronae and Craters: Implications for Corona Origin Hypothesis

NASA Astrophysics Data System (ADS)

Stoddard, P. R.; Jurdy, D. M.

2006-12-01

Venus' surface hosts nearly 1000 unambiguous impact craters, ranging in diameter from 1.5 to 280 km. Although the majority of these are pristine, slightly less than 200 have been modified by either volcanic or tectonic activity or both. In addition, numerous researchers have identified hundreds of ring-like features of varying morphology, termed "coronae." These have typically been thought of as having a diapiric or volcanic origin. Recently, however, based on the circular to quasi-circular nature of coronae, an alternative origin - impact - has been proposed. We compare the profiles across agreed-upon craters to several coronae that have been suggested as impact sites. For each feature, 36 profiles (taken every ten degrees) are aligned and then averaged together. For Mead, Cleopatra, Meitner, and Isabella craters, the profiles display the typical rim and basin structure expected for craters, but for Klenova crater the average is more domal, with only a few of the individual profiles looking crater-like. Among the "contested" coronae, the average profiles for Eurynome, Maya, and C21 appear crater-like, albeit with more variation among the individual profiles than seen in the agreed-upon craters. Anquet has a rim-and-basin structure, but unlike typical craters, the basin is elevated above the surrounding plains. Acrea appears to be a small hill in a large depression, again with a high degree of variability among the profiles. Ninhursag is clearly domal, and cannot be taken as a crater. A summary of the variability of the profiles - where 100% correlation would indicate perfect circular symmetry - indicates that, with the exception of Klenova, those features universally agreed-upon as craters have the highest correlation percentages - all at or above 80%. The disputed features are not as circular, although C21 is close. Based on this analysis, we conclude that Klenova has been mischaracterized as an impact crater, and that C21 and some other features previously classified as coronae may indeed be of impact origin. More careful analyses will be necessary to assess the origin of similar features.

Designing attractive gamification features for collaborative storytelling websites.

PubMed

Hsu, Shang Hwa; Chang, Jen-Wei; Lee, Chun-Chia

2013-06-01

Gamification design is considered as the predictor of collaborative storytelling websites' success. Although aforementioned studies have mentioned a broad range of factors that may influence gamification, they neither depicted the actual design features nor relative attractiveness among them. This study aims to identify attractive gamification features for collaborative storytelling websites. We first constructed a hierarchical system structure of gamification design of collaborative storytelling websites and conducted a focus group interview with eighteen frequent users to identify 35gamification features. After that, this study determined the relative attractiveness of these gamification features by administrating an online survey to 6333 collaborative storytelling websites users. The results indicated that the top 10 most attractive gamification features could account for more than 50% of attractiveness among these 35 gamification features. The feature of unpredictable time pressure is important to website users, yet not revealed in previous relevant studies. Implications of the findings were discussed.

Sensor-oriented feature usability evaluation in fingerprint segmentation

NASA Astrophysics Data System (ADS)

Li, Ying; Yin, Yilong; Yang, Gongping

2013-06-01

Existing fingerprint segmentation methods usually process fingerprint images captured by different sensors with the same feature or feature set. We propose to improve the fingerprint segmentation result in view of an important fact that images from different sensors have different characteristics for segmentation. Feature usability evaluation, which means to evaluate the usability of features to find the personalized feature or feature set for different sensors to improve the performance of segmentation. The need for feature usability evaluation for fingerprint segmentation is raised and analyzed as a new issue. To address this issue, we present a decision-tree-based feature-usability evaluation method, which utilizes a C4.5 decision tree algorithm to evaluate and pick the best suitable feature or feature set for fingerprint segmentation from a typical candidate feature set. We apply the novel method on the FVC2002 database of fingerprint images, which are acquired by four different respective sensors and technologies. Experimental results show that the accuracy of segmentation is improved, and time consumption for feature extraction is dramatically reduced with selected feature(s).

Forensic SNP genotyping with SNaPshot: Technical considerations for the development and optimization of multiplexed SNP assays.

PubMed

Fondevila, M; Børsting, C; Phillips, C; de la Puente, M; Consortium, Euroforen-NoE; Carracedo, A; Morling, N; Lareu, M V

2017-01-01

This review explores the key factors that influence the optimization, routine use, and profile interpretation of the SNaPshot single-base extension (SBE) system applied to forensic single-nucleotide polymorphism (SNP) genotyping. Despite being a mainly complimentary DNA genotyping technique to routine STR profiling, use of SNaPshot is an important part of the development of SNP sets for a wide range of forensic applications with these markers, from genotyping highly degraded DNA with very short amplicons to the introduction of SNPs to ascertain the ancestry and physical characteristics of an unidentified contact trace donor. However, this technology, as resourceful as it is, displays several features that depart from the usual STR genotyping far enough to demand a certain degree of expertise from the forensic analyst before tackling the complex casework on which SNaPshot application provides an advantage. In order to provide the basis for developing such expertise, we cover in this paper the most challenging aspects of the SNaPshot technology, focusing on the steps taken to design primer sets, optimize the PCR and single-base extension chemistries, and the important features of the peak patterns observed in typical forensic SNP profiles using SNaPshot. With that purpose in mind, we provide guidelines and troubleshooting for multiplex-SNaPshot-oriented primer design and the resulting capillary electrophoresis (CE) profile interpretation (covering the most commonly observed artifacts and expected departures from the ideal conditions). Copyright © 2017 Central Police University.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malashkevich, Vladimir N.; Higgins, Chelsea D.; Almo, Steven C.

The coiled-coil is one of the most ubiquitous and well studied protein structural motifs. Significant effort has been devoted to dissecting subtle variations of the typical heptad repeat sequence pattern that can designate larger topological features such as relative α-helical orientation and oligomer size. Here in this paper we report the X-ray structure of a model coiled-coil peptide, HA2-Del-L2seM, which forms an unanticipated core antiparallel dimer with potential sites for discrete higher-order multimerization (trimer or tetramer). In the X-ray structure, a third, partially-ordered α-helix is weakly associated with the antiparallel dimer and analytical ultracentrifugation experiments indicate the peptide forms amore » well-defined tetramer in solution. The HA2-Del-L2seM sequence is closely related to a parent model peptide, HA2-Del, which we previously reported adopts a parallel trimer; HA2-Del-L2seM differs by only hydrophobic leucine to selenomethione mutations and thus this subtle difference is sufficient to switch both relative α-helical topology and number of α-helices participating in the coiled-coil. Comparison of the X-ray structures of HA2-Del-L2seM (reported here) with the HA2-Del parent (reported previously) reveals novel interactions involving the selenomethionine residues that promote antiparallel coiled-coil configuration and preclude parallel trimer formation. Finally, these novel atomic insights are instructive for understanding subtle features that can affect coiled-coil topology and provide additional information for design of antiparallel coiled-coils.« less

An exploration of EEG features during recovery following stroke - implications for BCI-mediated neurorehabilitation therapy.

PubMed

Leamy, Darren J; Kocijan, Juš; Domijan, Katarina; Duffin, Joseph; Roche, Richard Ap; Commins, Sean; Collins, Ronan; Ward, Tomas E

2014-01-28

Brain-Computer Interfaces (BCI) can potentially be used to aid in the recovery of lost motor control in a limb following stroke. BCIs are typically used by subjects with no damage to the brain therefore relatively little is known about the technical requirements for the design of a rehabilitative BCI for stroke. 32-channel electroencephalogram (EEG) was recorded during a finger-tapping task from 10 healthy subjects for one session and 5 stroke patients for two sessions approximately 6 months apart. An off-line BCI design based on Filter Bank Common Spatial Patterns (FBCSP) was implemented to test and compare the efficacy and accuracy of training a rehabilitative BCI with both stroke-affected and healthy data. Stroke-affected EEG datasets have lower 10-fold cross validation results than healthy EEG datasets. When training a BCI with healthy EEG, average classification accuracy of stroke-affected EEG is lower than the average for healthy EEG. Classification accuracy of the late session stroke EEG is improved by training the BCI on the corresponding early stroke EEG dataset. This exploratory study illustrates that stroke and the accompanying neuroplastic changes associated with the recovery process can cause significant inter-subject changes in the EEG features suitable for mapping as part of a neurofeedback therapy, even when individuals have scored largely similar with conventional behavioural measures. It appears such measures can mask this individual variability in cortical reorganization. Consequently we believe motor retraining BCI should initially be tailored to individual patients.

An Artificial Neural Network for Movement Pattern Analysis to Estimate Blood Alcohol Content Level.

PubMed

Gharani, Pedram; Suffoletto, Brian; Chung, Tammy; Karimi, Hassan A

2017-12-13

Impairments in gait occur after alcohol consumption, and, if detected in real-time, could guide the delivery of "just-in-time" injury prevention interventions. We aimed to identify the salient features of gait that could be used for estimating blood alcohol content (BAC) level in a typical drinking environment. We recruited 10 young adults with a history of heavy drinking to test our research app. During four consecutive Fridays and Saturdays, every hour from 8 p.m. to 12 a.m., they were prompted to use the app to report alcohol consumption and complete a 5-step straight-line walking task, during which 3-axis acceleration and angular velocity data was sampled at a frequency of 100 Hz. BAC for each subject was calculated. From sensor signals, 24 features were calculated using a sliding window technique, including energy, mean, and standard deviation. Using an artificial neural network (ANN), we performed regression analysis to define a model determining association between gait features and BACs. Part (70%) of the data was then used as a training dataset, and the results tested and validated using the rest of the samples. We evaluated different training algorithms for the neural network and the result showed that a Bayesian regularization neural network (BRNN) was the most efficient and accurate. Analyses support the use of the tandem gait task paired with our approach to reliably estimate BAC based on gait features. Results from this work could be useful in designing effective prevention interventions to reduce risky behaviors during periods of alcohol consumption.

Power Systems and Energy Storage Modeling for Directed Energy Weapons

DTIC Science & Technology

2014-06-01

neodymium or ytterbium doped yttrium aluminum garnet (YAG) crystal.6 The Maritime Laser Demonstration (MLD) features several 15 kW slab lasers combined...The laser substrate is similar to a fiber optic cable that is doped with a rare earth element (typically neodymium or ytterbium); many fibers can be...but with different elements. A typical construction consists of a sheet of Lithium- cobalt -oxide and a sheet of carbon separated by an insulator

75 FR 2434 - Special Conditions: Boeing Model 747-8/-8F Series Airplanes; Design Roll Maneuver Requirement

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-15

... have novel or unusual design features when compared to the state of technology envisioned in the... standards. Additional special conditions will be issued for other novel or unusual design features of the... 747-8/-8F because of a novel or unusual design feature, special conditions are prescribed under the...

Turner Syndrome

MedlinePlus

Turner syndrome is a genetic disorder that affects a girl's development. The cause is a missing or incomplete ... t work properly. Other physical features typical of Turner syndrome are Short, "webbed" neck with folds of skin ...

Examining the design features of a communication-rich, problem-centred mathematics professional development

NASA Astrophysics Data System (ADS)

de Araujo, Zandra; Orrill, Chandra Hawley; Jacobson, Erik

2018-04-01

While there is considerable scholarship describing principles for effective professional development, there have been few attempts to examine these principles in practice. In this paper, we identify and examine the particular design features of a mathematics professional development experience provided for middle grades teachers over 14 weeks. The professional development was grounded in a set of mathematical tasks that each had one right answer, but multiple solution paths. The facilitator engaged participants in problem solving and encouraged participants to work collaboratively to explore different solution paths. Through analysis of this collaborative learning environment, we identified five design features for supporting teacher learning of important mathematics and pedagogy in a problem-solving setting. We discuss these design features in depth and illustrate them by presenting an elaborated example from the professional development. This study extends the existing guidance for the design of professional development by examining and operationalizing the relationships among research-based features of effective professional development and the enacted features of a particular design.

Handbook of International alloy Compositions and Designations. Volume II. Superalloys

DTIC Science & Technology

1978-12-01

Offered in Italy 169 Table 12 . Typical Superalloys Offered in Japan 170 Table 13. Typical Superalloys Specified by Sweden 171 Table 14... 12 . Typical Superalloys Offered in Japan Table 13. Typical Superalloys Specified by Sweden Table 14. Typical Superalloys Offered in the Union of...Engineering Properties, INCO Europe Limited, London, England (1976), 12 pp. 8. IN-657 Cast-Nickel-Chromium-Niobium Alloy for Service Against Fuel + Ash

A Prototype SSVEP Based Real Time BCI Gaming System

PubMed Central

Martišius, Ignas

2016-01-01

Although brain-computer interface technology is mainly designed with disabled people in mind, it can also be beneficial to healthy subjects, for example, in gaming or virtual reality systems. In this paper we discuss the typical architecture, paradigms, requirements, and limitations of electroencephalogram-based gaming systems. We have developed a prototype three-class brain-computer interface system, based on the steady state visually evoked potentials paradigm and the Emotiv EPOC headset. An online target shooting game, implemented in the OpenViBE environment, has been used for user feedback. The system utilizes wave atom transform for feature extraction, achieving an average accuracy of 78.2% using linear discriminant analysis classifier, 79.3% using support vector machine classifier with a linear kernel, and 80.5% using a support vector machine classifier with a radial basis function kernel. PMID:27051414

Electrochemical detection for microscale analytical systems: a review.

PubMed

Wang, Joseph

2002-02-11

As the field of chip-based microscale systems continues its rapid growth, there are urgent needs for developing compatible detection modes. Electrochemistry detection offers considerable promise for such microfluidic systems, with features that include remarkable sensitivity, inherent miniaturization and portability, independence of optical path length or sample turbidity, low cost, low-power requirements and high compatibility with advanced micromachining and microfabrication technologies. This paper highlights recent advances, directions and key strategies in controlled-potential electrochemical detectors for miniaturized analytical systems. Subjects covered include the design and integration of the electrochemical detection system, its requirements and operational principles, common electrode materials, derivatization reactions, electrical-field decouplers, typical applications and future prospects. It is expected that electrochemical detection will become a powerful tool for microscale analytical systems and will facilitate the creation of truly portable (and possibly disposable) devices.

The BLAZE language: A parallel language for scientific programming

NASA Technical Reports Server (NTRS)

Mehrotra, P.; Vanrosendale, J.

1985-01-01

A Pascal-like scientific programming language, Blaze, is described. Blaze contains array arithmetic, forall loops, and APL-style accumulation operators, which allow natural expression of fine grained parallelism. It also employs an applicative or functional procedure invocation mechanism, which makes it easy for compilers to extract coarse grained parallelism using machine specific program restructuring. Thus Blaze should allow one to achieve highly parallel execution on multiprocessor architectures, while still providing the user with onceptually sequential control flow. A central goal in the design of Blaze is portability across a broad range of parallel architectures. The multiple levels of parallelism present in Blaze code, in principle, allow a compiler to extract the types of parallelism appropriate for the given architecture while neglecting the remainder. The features of Blaze are described and shows how this language would be used in typical scientific programming.

Astronomy on Tap as a Professional Development Tool

NASA Astrophysics Data System (ADS)

Rice, Emily; Burtnyk, Kimberly; Silverman, Jeffrey; Popinchalk, Mark; Constellation of Astronomy On Tap Host Stars

2018-01-01

We lured scientists, educators, and other astronomy enthusiasts into bars around the world with promises of fun public outreach, but we secretly provided them with networking opportunities and taught them how to be better communicators! Astronomy on Tap (AoT) events began in New York City in 2013, and since then nearly 400 events (featuring 1-6 presenters each) have been organized by over 100 people in over 30 locations across the U.S. and around the world. Implicit in the design of typical AoT events are opportunities for professional development in several areas, most prominently in networking and science communication. We surveyed organizers and presenters to assess the extent to which they have benefited from these opportunities. We report results from that survey and present plans for codifying professional development aspects of AoT events for future implementation.

Object-oriented recognition of high-resolution remote sensing image

NASA Astrophysics Data System (ADS)

Wang, Yongyan; Li, Haitao; Chen, Hong; Xu, Yuannan

2016-01-01

With the development of remote sensing imaging technology and the improvement of multi-source image's resolution in satellite visible light, multi-spectral and hyper spectral , the high resolution remote sensing image has been widely used in various fields, for example military field, surveying and mapping, geophysical prospecting, environment and so forth. In remote sensing image, the segmentation of ground targets, feature extraction and the technology of automatic recognition are the hotspot and difficulty in the research of modern information technology. This paper also presents an object-oriented remote sensing image scene classification method. The method is consist of vehicles typical objects classification generation, nonparametric density estimation theory, mean shift segmentation theory, multi-scale corner detection algorithm, local shape matching algorithm based on template. Remote sensing vehicles image classification software system is designed and implemented to meet the requirements .

A Prototype SSVEP Based Real Time BCI Gaming System.

PubMed

Martišius, Ignas; Damaševičius, Robertas

2016-01-01

Although brain-computer interface technology is mainly designed with disabled people in mind, it can also be beneficial to healthy subjects, for example, in gaming or virtual reality systems. In this paper we discuss the typical architecture, paradigms, requirements, and limitations of electroencephalogram-based gaming systems. We have developed a prototype three-class brain-computer interface system, based on the steady state visually evoked potentials paradigm and the Emotiv EPOC headset. An online target shooting game, implemented in the OpenViBE environment, has been used for user feedback. The system utilizes wave atom transform for feature extraction, achieving an average accuracy of 78.2% using linear discriminant analysis classifier, 79.3% using support vector machine classifier with a linear kernel, and 80.5% using a support vector machine classifier with a radial basis function kernel.

A 15,000-hour cyclic endurance test of an 8-centimeter-diameter electron bombardment mercury ion thruster

NASA Technical Reports Server (NTRS)

Nakanishi, S.

1976-01-01

A laboratory model 8-cm thruster with improvements to minimize ion chamber erosion and peeling of sputtered metal was subjected to a cyclic endurance test for 15,040 hours and 460 restarts. A charted history of several thruster operating variables and off-normal events are shown in 600-hour segments at three points in the test. The transient behavior of these variables during a typical start-stop cycle is presented. Performance and operating characteristics were nearly constant throughout the test except for a change in the accelerator back-streaming limit. Findings of the post-test inspection confirmed most of the expected results. Charge-exchange ions caused normal accelerator grid erosion. The workability of the various design features have been substantiated, and attainable improvements in propellant utilization efficiency should significantly reduce accelerator erosion.

Evaluation Study of Pedagogical Methods and E - Learning Material via Web 2.0 for Hearing Impaired People

NASA Astrophysics Data System (ADS)

Vrettaros, John; Argiri, Katerina; Stavrou, Pilios; Hrissagis, Kostas; Drigas, Athanasios

The primary goal of this paper is to study whether WEB 2.0 tools such as blogs, wikis, social networks and typical hypermedia as well as techniques such as lip - reading, video - sign language and learning activities are appropriate to use for learning purpose for deaf and hard of hearing people. In order to check the extent in which the choices mentioned above are compatible with the features of the specific group and maximize the learning results we designed an empirical study which will be presented below. The study was conducted in the context of SYNERGIA, a project of Leonardo da Vinci of Lifelong Learning Programme, in the section of MULTILATERAL PROJECTS TRANSFER OF INNOVATION, The evaluation was conducted on data that came up through questionnaire analysis.

Space shuttle rendezous, radiation and reentry analysis code

NASA Technical Reports Server (NTRS)

Mcglathery, D. M.

1973-01-01

A preliminary space shuttle mission design and analysis tool is reported emphasizing versatility, flexibility, and user interaction through the use of a relatively small computer (IBM-7044). The Space Shuttle Rendezvous, Radiation and Reentry Analysis Code is used to perform mission and space radiation environmental analyses for four typical space shuttle missions. Included also is a version of the proposed Apollo/Soyuz rendezvous and docking test mission. Tangential steering circle to circle low-thrust tug orbit raising and the effects of the trapped radiation environment on trajectory shaping due to solar electric power losses are also features of this mission analysis code. The computational results include a parametric study on single impulse versus double impulse deorbiting for relatively low space shuttle orbits as well as some definitive data on the magnetically trapped protons and electrons encountered on a particular mission.

Size-Related Changes in Foot Impact Mechanics in Hoofed Mammals

PubMed Central

Warner, Sharon Elaine; Pickering, Phillip; Panagiotopoulou, Olga; Pfau, Thilo; Ren, Lei; Hutchinson, John Richard

2013-01-01

Foot-ground impact is mechanically challenging for all animals, but how do large animals mitigate increased mass during foot impact? We hypothesized that impact force amplitude scales according to isometry in animals of increasing size through allometric scaling of related impact parameters. To test this, we measured limb kinetics and kinematics in 11 species of hoofed mammals ranging from 18–3157 kg body mass. We found impact force amplitude to be maintained proportional to size in hoofed mammals, but that other features of foot impact exhibit differential scaling patterns depending on the limb; forelimb parameters typically exhibit higher intercepts with lower scaling exponents than hind limb parameters. Our explorations of the size-related consequences of foot impact advance understanding of how body size influences limb morphology and function, foot design and locomotor behaviour. PMID:23382967

Apparatus for measurement of acoustic wave propagation under uniaxial loading with application to measurement of third-order elastic constants of piezoelectric single crystals.

PubMed

Zhang, Haifeng; Kosinski, J A; Karim, Md Afzalul

2013-05-01

We describe an apparatus for the measurement of acoustic wave propagation under uniaxial loading featuring a special mechanism designed to assure a uniform mechanical load on a cube-shaped sample of piezoelectric material. We demonstrate the utility of the apparatus by determining the effects of stresses on acoustic wave speed, which forms a foundation for the final determination of the third-order elastic constants of langasite and langatate single crystals. The transit time method is used to determine changes in acoustic wave velocity as the loading is varied. In order to minimize error and improve the accuracy of the wave speed measurements, the cross correlation method is used to determine the small changes in the time of flight. Typical experimental results are presented and discussed.

Yoga for Youth in Pain

PubMed Central

Evans, Subhadra; Moieni, Mona; Sternlieb, Beth; Tsao, Jennie C.I; Zeltzer, Lonnie K.

2012-01-01

Children, adolescents, and young adults do not typically feature in clinics, studies, and mainstream notions of chronic pain. Yet many young people experience debilitating pain for extended periods of time. Chronic pain in these formative years may be especially important to treat in order for young patients to maintain life tasks and to prevent protracted disability. The Pediatric Pain Program at the University of California, Los Angeles, is a multidisciplinary treatment program designed for young people with chronic pain and their families. We offer both conventional and complementary medicine to treat the whole individual. This article describes the work undertaken in the clinic and our newly developed Yoga for Youth Research Program. The clinical and research programs fill a critical need to provide service to youth with chronic pain and to scientifically study one of the more popular complementary treatments we offer, Iyengar yoga. PMID:22864296

Unraveling the Molecular Requirements for Macroscopic Silk Supercontraction.

PubMed

Giesa, Tristan; Schuetz, Roman; Fratzl, Peter; Buehler, Markus J; Masic, Admir

2017-10-24

Spider dragline silk is a protein material that has evolved over millions of years to achieve finely tuned mechanical properties. A less known feature of some dragline silk fibers is that they shrink along the main axis by up to 50% when exposed to high humidity, a phenomenon called supercontraction. This contrasts the typical behavior of many other materials that swell when exposed to humidity. Molecular level details and mechanisms of the supercontraction effect are heavily debated. Here we report a molecular dynamics analysis of supercontraction in Nephila clavipes silk combined with in situ mechanical testing and Raman spectroscopy linking the reorganization of the nanostructure to the polar and charged amino acids in the sequence. We further show in our in silico approach that point mutations of these groups not only suppress the supercontraction effect, but even reverse it, while maintaining the exceptional mechanical properties of the silk material. This work has imminent impact on the design of biomimetic equivalents and recombinant silks for which supercontraction may or may not be a desirable feature. The approach applied is appropriate to explore the effect of point mutations on the overall physical properties of protein based materials.

Filter Design and Performance Evaluation for Fingerprint Image Segmentation

PubMed Central

Thai, Duy Hoang; Huckemann, Stephan; Gottschlich, Carsten

2016-01-01

Fingerprint recognition plays an important role in many commercial applications and is used by millions of people every day, e.g. for unlocking mobile phones. Fingerprint image segmentation is typically the first processing step of most fingerprint algorithms and it divides an image into foreground, the region of interest, and background. Two types of error can occur during this step which both have a negative impact on the recognition performance: ‘true’ foreground can be labeled as background and features like minutiae can be lost, or conversely ‘true’ background can be misclassified as foreground and spurious features can be introduced. The contribution of this paper is threefold: firstly, we propose a novel factorized directional bandpass (FDB) segmentation method for texture extraction based on the directional Hilbert transform of a Butterworth bandpass (DHBB) filter interwoven with soft-thresholding. Secondly, we provide a manually marked ground truth segmentation for 10560 images as an evaluation benchmark. Thirdly, we conduct a systematic performance comparison between the FDB method and four of the most often cited fingerprint segmentation algorithms showing that the FDB segmentation method clearly outperforms these four widely used methods. The benchmark and the implementation of the FDB method are made publicly available. PMID:27171150

Automatic and adaptive heterogeneous refractive index compensation for light-sheet microscopy.

PubMed

Ryan, Duncan P; Gould, Elizabeth A; Seedorf, Gregory J; Masihzadeh, Omid; Abman, Steven H; Vijayaraghavan, Sukumar; Macklin, Wendy B; Restrepo, Diego; Shepherd, Douglas P

2017-09-20

Optical tissue clearing has revolutionized researchers' ability to perform fluorescent measurements of molecules, cells, and structures within intact tissue. One common complication to all optically cleared tissue is a spatially heterogeneous refractive index, leading to light scattering and first-order defocus. We designed C-DSLM (cleared tissue digital scanned light-sheet microscopy) as a low-cost method intended to automatically generate in-focus images of cleared tissue. We demonstrate the flexibility and power of C-DSLM by quantifying fluorescent features in tissue from multiple animal models using refractive index matched and mismatched microscope objectives. This includes a unique measurement of myelin tracks within intact tissue using an endogenous fluorescent reporter where typical clearing approaches render such structures difficult to image. For all measurements, we provide independent verification using standard serial tissue sectioning and quantification methods. Paired with advancements in volumetric image processing, C-DSLM provides a robust methodology to quantify sub-micron features within large tissue sections.Optical clearing of tissue has enabled optical imaging deeper into tissue due to significantly reduced light scattering. Here, Ryan et al. tackle first-order defocus, an artefact of a non-uniform refractive index, extending light-sheet microscopy to partially cleared samples.

Regional information guidance system based on hypermedia concept

NASA Astrophysics Data System (ADS)

Matoba, Hiroshi; Hara, Yoshinori; Kasahara, Yutako

1990-08-01

A regional information guidance system has been developed on an image workstation. Two main features of this system are hypermedia data structure and friendly visual interface realized by the full-color frame memory system. As the hypermedia data structure manages regional information such as maps, pictures and explanations of points of interest, users can retrieve those information one by one, next to next according to their interest change. For example, users can retrieve explanation of a picture through the link between pictures and text explanations. Users can also traverse from one document to another by using keywords as cross reference indices. The second feature is to utilize a full-color, high resolution and wide space frame memory for visual interface design. This frame memory system enables real-time operation of image data and natural scene representation. The system also provides half tone representing function which enables fade-in/out presentations. This fade-in/out functions used in displaying and erasing menu and image data, makes visual interface soft for human eyes. The system we have developed is a typical example of multimedia applications. We expect the image workstation will play an important role as a platform for multimedia applications.

Angle and Context Free Grammar Based Precarious Node Detection and Secure Data Transmission in MANETs.

PubMed

Veerasamy, Anitha; Madane, Srinivasa Rao; Sivakumar, K; Sivaraman, Audithan

2016-01-01

Growing attractiveness of Mobile Ad Hoc Networks (MANETs), its features, and usage has led to the launching of threats and attacks to bring negative consequences in the society. The typical features of MANETs, especially with dynamic topology and open wireless medium, may leave MANETs vulnerable. Trust management using uncertain reasoning scheme has previously attempted to solve this problem. However, it produces additional overhead while securing the network. Hence, a Location and Trust-based secure communication scheme (L&TS) is proposed to overcome this limitation. Since the design securing requires more than two data algorithms, the cost of the system goes up. Another mechanism proposed in this paper, Angle and Context Free Grammar (ACFG) based precarious node elimination and secure communication in MANETs, intends to secure data transmission and detect precarious nodes in a MANET at a comparatively lower cost. The Elliptic Curve function is used to isolate a malicious node, thereby incorporating secure data transfer. Simulation results show that the dynamic estimation of the metrics improves throughput by 26% in L&TS when compared to the TMUR. ACFG achieves 33% and 51% throughput increase when compared to L&TS and TMUR mechanisms, respectively.

Numerical Assessment of Novel Helical/Spiral Grafts with Improved Hemodynamics for Distal Graft Anastomoses

PubMed Central

Kabinejadian, Foad; McElroy, Michael; Ruiz-Soler, Andres; Leo, Hwa Liang; Slevin, Mark A.; Badimon, Lina

2016-01-01

In the present work, numerical simulations were conducted for a typical end-to-side distal graft anastomosis to assess the effects of inducing secondary flow, which is believed to remove unfavourable flow environment. Simulations were carried out for four models, generated based on two main features of 'out-of-plane helicity' and 'spiral ridge' in the grafts as well as their combination. Following a qualitative comparison against in vitro data, various mean flow and hemodynamic parameters were compared and the results showed that helicity is significantly more effective in inducing swirling flow in comparison to a spiral ridge, while their combination could be even more effective. In addition, the induced swirling flow was generally found to be increasing the wall shear stress and reducing the flow stagnation and particle residence time within the anastomotic region and the host artery, which may be beneficial to the graft longevity and patency rates. Finally, a parametric study on the spiral ridge geometrical features was conducted, which showed that the ridge height and the number of spiral ridges have significant effects on inducing swirling flow, and revealed the potential of improving the efficiency of such designs. PMID:27861485

Grading evidence from test accuracy studies: what makes it challenging compared with the grading of effectiveness studies?

PubMed

Rogozińska, Ewelina; Khan, Khalid

2017-06-01

Guideline panels need to process a sizeable amount of information to issue a decision on whether to recommend a health technology or not. Grading of Recommendations Assessment, Development, and Evaluation (GRADE) is being frequently applied in guideline development to facilitate this task, typically for the synthesis of effectiveness research. Questions regarding the accuracy of medical tests are ubiquitous, and they temporally precede questions about therapy. However, literature summarising the experience of applying GRADE approach to accuracy evaluations is not as rich as one for effectiveness evidence. Type of study design (cross-sectional), two-dimensional nature of the performance measures (sensitivity and specificity), propensity towards a higher level of between-study heterogeneity, poor reporting of quality features and uncertainty about how best to assess for publication bias among other features make this task challenging. This article presents solutions adopted to addresses above challenges for judicious estimation of the strength of test accuracy evidence used to inform evidence syntheses for guideline development. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Kinetic features revealed by top-hat electrostatic analysers: numerical simulations and instrument response results

NASA Astrophysics Data System (ADS)

De Marco, Rossana; Marcucci, Maria Federica; Brienza, Daniele; Bruno, Roberto; Consolini, Giuseppe; Perrone, Denise; Valentini, Franceso; Servidio, Sergio; Stabile, Sara; Pezzi, Oreste; Sorriso-Valvo, Luca; Lavraud, Benoit; De Keyser, Johan; Retinò, Alessandro; Fazakerley, Andrew; Wicks, Robert; Vaivads, Andris; Salatti, Mario; Veltri, Pierliugi

2017-04-01

Turbulence Heating ObserveR (THOR) is the first mission devoted to study energization, acceleration and heating of turbulent space plasmas, and designed to perform field and particle measurements at kinetic scales in different near-Earth regions and in the solar wind. Solar Orbiter (SolO), together with Solar Probe Plus, will provide the first comprehensive remote and in situ measurements which are critical to establish the fundamental physical links between the Sun's dynamic atmosphere and the turbulent solar wind. The fundamental process of turbulent dissipation is mediated by physical mechanism that occur at a variety of temporal and spatial scales, and most efficiently at the kinetics scales. Hybrid Vlasov-Maxwell simulations of solar-wind turbulence show that kinetic effects manifest as particle beams, production of temperature anisotropies and ring-like modulations, preferential heating of heavy ions. We use a numerical code able to reproduce the response of a typical electrostatic analyzer of top-hat type starting from velocity distribution functions (VDFs) generated by Hybrid Vlasov-Maxwell (HVM) numerical simulations. Here, we show how optimized particle measurements by top-hat analysers can capture the kinetic features injected by turbulence in the VDFs.

A generalized strategy for designing (19)F/(1)H dual-frequency MRI coil for small animal imaging at 4.7 Tesla.

PubMed

Hu, Lingzhi; Hockett, Frank D; Chen, Junjie; Zhang, Lei; Caruthers, Shelton D; Lanza, Gregory M; Wickline, Samuel A

2011-07-01

To propose and test a universal strategy for building (19) F/(1) H dual-frequency RF coil that permits multiple coil geometries. The feasibility to design (19) F/(1) H dual-frequency RF coil based on coupled resonator model was investigated. A series capacitive matching network enables robust impedance matching for both harmonic oscillating modes of the coupled resonator. Two typical designs of (19) F/(1) H volume coils (birdcage and saddle) at 4.7T were implemented and evaluated with electrical bench test and in vivo (19) F/(1) H dual-nuclei imaging. For various combinations of internal resistances of the sample coil and secondary resonator, numerical solutions for the tunable capacitors to optimize impedance matching were obtained using a root-seeking program. Identical and homogeneous B1 field distribution at (19) F and (1) H frequencies were observed in bench test and phantom image. Finally, in vivo mouse imaging confirmed the sensitivity and homogeneity of the (19) F/(1) H dual-frequency coil design. A generalized strategy for designing (19) F/(1) H dual-frequency coils based on the coupled resonator approach was developed and validated. A unique feature of this design is that it preserves the B1 field homogeneity of the RF coil at both resonant frequencies. Thus it minimizes the susceptibility effect on image co-registration. Copyright © 2011 Wiley-Liss, Inc.

Design framework for entanglement-distribution switching networks

NASA Astrophysics Data System (ADS)

Drost, Robert J.; Brodsky, Michael

2016-09-01

The distribution of quantum entanglement appears to be an important component of applications of quantum communications and networks. The ability to centralize the sourcing of entanglement in a quantum network can provide for improved efficiency and enable a variety of network structures. A necessary feature of an entanglement-sourcing network node comprising several sources of entangled photons is the ability to reconfigurably route the generated pairs of photons to network neighbors depending on the desired entanglement sharing of the network users at a given time. One approach to such routing is the use of a photonic switching network. The requirements for an entanglement distribution switching network are less restrictive than for typical conventional applications, leading to design freedom that can be leveraged to optimize additional criteria. In this paper, we present a mathematical framework defining the requirements of an entanglement-distribution switching network. We then consider the design of such a switching network using a number of 2 × 2 crossbar switches, addressing the interconnection of these switches and efficient routing algorithms. In particular, we define a worst-case loss metric and consider 6 × 6, 8 × 8, and 10 × 10 network designs that optimize both this metric and the number of crossbar switches composing the network. We pay particular attention to the 10 × 10 network, detailing novel results proving the optimality of the proposed design. These optimized network designs have great potential for use in practical quantum networks, thus advancing the concept of quantum networks toward reality.

Mosaic Double Aneuploidy of X and G Chromosomes

ERIC Educational Resources Information Center

And Others; Singh, D. N.

1975-01-01

Reported are case histories of three severely retarded adolescents with typical Down's Syndrome features but whose cytogenetic analysis revealed a rare chromosomal anomaly of mosaicism of Down's and Turner's syndromes. (CL)

77 FR 64023 - Special Conditions: Airbus Model A318, A319, A320, and A321 Series Airplanes; Design Roll...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-18

... airplanes with modification 160023 (Sharklet). These airplanes will have novel or unusual design features..., A320, and A321 series airplanes because of a novel or unusual design feature, special conditions are... model that incorporates the same novel or unusual design feature, or should any other model already...

78 FR 67291 - Special Conditions: Bombardier Inc., Models BD-500-1A10 and BD-500-1A11 Series Airplanes; Design...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-12

... have a novel or unusual design feature associated with an electronic flight control system that... because of a novel or unusual design feature, special conditions are prescribed under the provisions of... same or similar novel or unusual design feature, the special conditions would also apply to the other...

The Communicability of Graphical Alternatives to Tabular Displays of Statistical Simulation Studies

PubMed Central

Cook, Alex R.; Teo, Shanice W. L.

2011-01-01

Simulation studies are often used to assess the frequency properties and optimality of statistical methods. They are typically reported in tables, which may contain hundreds of figures to be contrasted over multiple dimensions. To assess the degree to which these tables are fit for purpose, we performed a randomised cross-over experiment in which statisticians were asked to extract information from (i) such a table sourced from the literature and (ii) a graphical adaptation designed by the authors, and were timed and assessed for accuracy. We developed hierarchical models accounting for differences between individuals of different experience levels (under- and post-graduate), within experience levels, and between different table-graph pairs. In our experiment, information could be extracted quicker and, for less experienced participants, more accurately from graphical presentations than tabular displays. We also performed a literature review to assess the prevalence of hard-to-interpret design features in tables of simulation studies in three popular statistics journals, finding that many are presented innumerately. We recommend simulation studies be presented in graphical form. PMID:22132184

Recent Development of Advanced Electrode Materials by Atomic Layer Deposition for Electrochemical Energy Storage.

PubMed

Guan, Cao; Wang, John

2016-10-01

Electrode materials play a decisive role in almost all electrochemical energy storage devices, determining their overall performance. Proper selection, design and fabrication of electrode materials have thus been regarded as one of the most critical steps in achieving high electrochemical energy storage performance. As an advanced nanotechnology for thin films and surfaces with conformal interfacial features and well controllable deposition thickness, atomic layer deposition (ALD) has been successfully developed for deposition and surface modification of electrode materials, where there are considerable issues of interfacial and surface chemistry at atomic and nanometer scale. In addition, ALD has shown great potential in construction of novel nanostructured active materials that otherwise can be hardly obtained by other processing techniques, such as those solution-based processing and chemical vapor deposition (CVD) techniques. This review focuses on the recent development of ALD for the design and delivery of advanced electrode materials in electrochemical energy storage devices, where typical examples will be highlighted and analyzed, and the merits and challenges of ALD for applications in energy storage will also be discussed.

Improving online risk assessment with equipment prognostics and health monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coble, Jamie B.; Liu, Xiaotong; Briere, Chris

The current approach to evaluating the risk of nuclear power plant (NPP) operation relies on static probabilities of component failure, which are based on industry experience with the existing fleet of nominally similar light water reactors (LWRs). As the nuclear industry looks to advanced reactor designs that feature non-light water coolants (e.g., liquid metal, high temperature gas, molten salt), this operating history is not available. Many advanced reactor designs use advanced components, such as electromagnetic pumps, that have not been used in the US commercial nuclear fleet. Given the lack of rich operating experience, we cannot accurately estimate the evolvingmore » probability of failure for basic components to populate the fault trees and event trees that typically comprise probabilistic risk assessment (PRA) models. Online equipment prognostics and health management (PHM) technologies can bridge this gap to estimate the failure probabilities for components under operation. The enhanced risk monitor (ERM) incorporates equipment condition assessment into the existing PRA and risk monitor framework to provide accurate and timely estimates of operational risk.« less

Recent Development of Advanced Electrode Materials by Atomic Layer Deposition for Electrochemical Energy Storage

PubMed Central

2016-01-01

Electrode materials play a decisive role in almost all electrochemical energy storage devices, determining their overall performance. Proper selection, design and fabrication of electrode materials have thus been regarded as one of the most critical steps in achieving high electrochemical energy storage performance. As an advanced nanotechnology for thin films and surfaces with conformal interfacial features and well controllable deposition thickness, atomic layer deposition (ALD) has been successfully developed for deposition and surface modification of electrode materials, where there are considerable issues of interfacial and surface chemistry at atomic and nanometer scale. In addition, ALD has shown great potential in construction of novel nanostructured active materials that otherwise can be hardly obtained by other processing techniques, such as those solution‐based processing and chemical vapor deposition (CVD) techniques. This review focuses on the recent development of ALD for the design and delivery of advanced electrode materials in electrochemical energy storage devices, where typical examples will be highlighted and analyzed, and the merits and challenges of ALD for applications in energy storage will also be discussed. PMID:27840793

Minimizing Experimental Setup Time and Effort at APS beamline 1-ID through Instrumentation Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benda, Erika; Almer, Jonathan; Kenesei, Peter

2016-01-01

Sector 1-ID at the APS accommodates a number of dif-ferent experimental techniques in the same spatial enve-lope of the E-hutch end station. These include high-energy small and wide angle X-ray scattering (SAXS and WAXS), high-energy diffraction microscopy (HEDM, both near and far field modes) and high-energy X-ray tomography. These techniques are frequently combined to allow the users to obtain multimodal data, often attaining 1 μm spatial resolution and <0.05º angular resolution. Furthermore, these techniques are utilized while the sam-ple is thermo-mechanically loaded to mimic real operat-ing conditions. The instrumentation required for each of these techniques and environments has been designedmore » and configured in a modular way with a focus on stability and repeatability between changeovers. This approach allows the end station to be more versatile, capable of collecting multi-modal data in-situ while reducing time and effort typically required for set up and alignment, resulting in more efficient beam time use. Key instrumentation de-sign features and layout of the end station are presented.« less

Enabling Object Storage via shims for Grid Middleware

NASA Astrophysics Data System (ADS)

Cadellin Skipsey, Samuel; De Witt, Shaun; Dewhurst, Alastair; Britton, David; Roy, Gareth; Crooks, David

2015-12-01

The Object Store model has quickly become the basis of most commercially successful mass storage infrastructure, backing so-called ”Cloud” storage such as Amazon S3, but also underlying the implementation of most parallel distributed storage systems. Many of the assumptions in Object Store design are similar, but not identical, to concepts in the design of Grid Storage Elements, although the requirement for ”POSIX-like” filesystem structures on top of SEs makes the disjunction seem larger. As modern Object Stores provide many features that most Grid SEs do not (block level striping, parallel access, automatic file repair, etc.), it is of interest to see how easily we can provide interfaces to typical Object Stores via plugins and shims for Grid tools, and how well experiments can adapt their data models to them. We present evaluation of, and first-deployment experiences with, (for example) Xrootd-Ceph interfaces for direct object-store access, as part of an initiative within GridPP[1] hosted at RAL. Additionally, we discuss the tradeoffs and experience of developing plugins for the currently-popular Ceph parallel distributed filesystem for the GFAL2 access layer, at Glasgow.

Novel circuits for energizing manganin stress gauges

NASA Astrophysics Data System (ADS)

Tasker, Douglas G.

2017-01-01

This paper describes the design of a novel MOSFET pulsed constant current supplies for low impedance Manganin stress gauges. The design emphasis has been on high accuracy, low noise, simple, low cost, disposable supplies that can be used to energize multiple gauges in explosive or shock experiments. The Manganin gauges used to measure stresses in detonating explosive experiments have typical resistances of 50 mΩ and are energized with pulsed currents of 50 A. Conventional pulsed, constant current supplies for these gauges are high voltage devices with outputs as high as 500 V. Common problems with the use of high voltage supplies at explosive firing sites are: erroneous signals caused by ground loops; overdrive of oscilloscopes on gauge failure; gauge signal crosstalk; cost; and errors due to changing load impedances. The new circuit corrects these issues. It is an 18-V circuit, powered by 9-V alkaline batteries, and features an optically isolated trigger, and single-point grounding. These circuits have been successfully tested at the Los Alamos National Laboratory in explosive experiments. [LA-UR-15-24819

Biomechanics of the Sensor–Tissue Interface—Effects of Motion, Pressure, and Design on Sensor Performance and Foreign Body Response—Part II: Examples and Application

PubMed Central

Helton, Kristen L; Ratner, Buddy D; Wisniewski, Natalie A

2011-01-01

This article is the second part of a two-part review in which we explore the biomechanics of the sensor–tissue interface as an important aspect of continuous glucose sensor biocompatibility. Part I, featured in this issue of Journal of Diabetes Science and Technology, describes a theoretical framework of how biomechanical factors such as motion and pressure (typically micromotion and micropressure) affect tissue physiology around a sensor and in turn, impact sensor performance. Here in Part II, a literature review is presented that summarizes examples of motion or pressure affecting sensor performance. Data are presented that show how both acute and chronic forces can impact continuous glucose monitor signals. Also presented are potential strategies for countering the ill effects of motion and pressure on glucose sensors. Improved engineering and optimized chemical biocompatibility have advanced sensor design and function, but we believe that mechanical biocompatibility, a rarely considered factor, must also be optimized in order to achieve an accurate, long-term, implantable sensor. PMID:21722579

Observation of rare-earth segregation in silicon nitride ceramics at subnanometre dimensions.

PubMed

Shibata, Naoya; Pennycook, Stephen J; Gosnell, Tim R; Painter, Gayle S; Shelton, William A; Becher, Paul F

2004-04-15

Silicon nitride (Si3N4) ceramics are used in numerous applications because of their superior mechanical properties. Their intrinsically brittle nature is a critical issue, but can be overcome by introducing whisker-like microstructural features. However, the formation of such anisotropic grains is very sensitive to the type of cations used as the sintering additives. Understanding the origin of dopant effects, central to the design of high-performance Si3N4 ceramics, has been sought for many years. Here we show direct images of dopant atoms (La) within the nanometre-scale intergranular amorphous films typically found at grain boundaries, using aberration corrected Z-contrast scanning transmission electron microscopy. It is clearly shown that the La atoms preferentially segregate to the amorphous/crystal interfaces. First-principles calculations confirm the strong preference of La for the crystalline surfaces, which is essential for forming elongated grains and a toughened microstructure. Whereas principles of micrometre-scale structural design are currently used to improve the mechanical properties of ceramics, this work represents a step towards the atomic-level structural engineering required for the next generation of ceramics.

The communicability of graphical alternatives to tabular displays of statistical simulation studies.

PubMed

Cook, Alex R; Teo, Shanice W L

2011-01-01

Simulation studies are often used to assess the frequency properties and optimality of statistical methods. They are typically reported in tables, which may contain hundreds of figures to be contrasted over multiple dimensions. To assess the degree to which these tables are fit for purpose, we performed a randomised cross-over experiment in which statisticians were asked to extract information from (i) such a table sourced from the literature and (ii) a graphical adaptation designed by the authors, and were timed and assessed for accuracy. We developed hierarchical models accounting for differences between individuals of different experience levels (under- and post-graduate), within experience levels, and between different table-graph pairs. In our experiment, information could be extracted quicker and, for less experienced participants, more accurately from graphical presentations than tabular displays. We also performed a literature review to assess the prevalence of hard-to-interpret design features in tables of simulation studies in three popular statistics journals, finding that many are presented innumerately. We recommend simulation studies be presented in graphical form.

Scientific Message Translation and the Heuristic Systematic Model: Insights for Designing Educational Messages About Progesterone and Breast Cancer Risks

PubMed Central

Perrault, Evan; Smith, Sandi; Keating, David M.; Nazione, Samantha; Silk, Kami; Russell, Jessica

2017-01-01

Results of ongoing scientific research on environmental determinants of breast cancer are not typically presented to the public in ways they can easily understand and use to take preventive actions. In this study, results of scientific studies on progesterone exposure as a risk factor for breast cancer were translated into high and low literacy level messages. Using the heuristic systematic model, this study examined how ability, motivation, and message processing (heuristic and systematic) influenced perceptions of risk beliefs and negative attitudes about progesterone exposure among women who read the translated scientific messages. Among the 1254 participants, those given the higher literacy level message had greater perceptions of risk about progesterone. Heuristic message cues of source credibility and perceived message quality, as well as motivation, also predicted risk beliefs. Finally, risk beliefs were a strong predictor of negative attitudes about exposure to progesterone. The results can help improve health education message design in terms of practitioners having better knowledge of message features that are the most persuasive to the target audiences on this topic. PMID:25903053

Aggregation-Induced Emission of Multiphenyl-Substituted 1,3-Butadiene Derivatives: Synthesis, Property and Application.

PubMed

Zhang, Yahui; Mao, Huiling; Xu, Weiquan; Shi, Jianbing; Cai, Zhengxu; Tong, Bin; Dong, Yuping

2018-05-29

Organic functional materials, including conjugated molecules and fluorescent dyes, have been rapidly developed in recent years because they can be applied in many fields, such as solar cells, biosensing and bioimaging, and medical adjuvant therapy. Organic functional materials with aggregation-induced emission or aggregation-enhanced emission (AIE/AEE) characteristics have increasingly attracted attention due to their high quantum efficiency in the aggregated or solid state. A large variety of AIE/AEE materials have been designed and applied during the exponential growth of research interest in the abovementioned fields. Multiphenyl-substituted 1,3-butadiene (MPB), as a core structure that includes tetraphenyl-1,3-butadiene, hexaphenyl-1,3-butadiene and their derivatives, show a typical AIE/AEE feature and can be potentially used in all the abovementioned fields. This review summarizes the design principles, the corresponding syntheses, and the structure-property relationships of MPBs, as well as their excellent innovative functionalities and applications. This review will be very useful for scientists conducting chemistry, materials, and biomedical research in AIE/AEE-related fields. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study of power management technology for orbital multi-100KWe applications. Volume 2: Study results

NASA Technical Reports Server (NTRS)

Mildice, J. W.

1980-01-01

The preliminary requirements and technology advances required for cost effective space power management systems for multi-100 kilowatt requirements were identified. System requirements were defined by establishing a baseline space platform in the 250 KE KWe range and examining typical user loads and interfaces. The most critical design parameters identified for detailed analysis include: increased distribution voltages and space plasma losses, the choice between ac and dc distribution systems, shuttle servicing effects on reliability, life cycle costs, and frequency impacts to power management system and payload systems for AC transmission. The first choice for a power management system for this kind of application and size range is a hybrid ac/dc combination with the following major features: modular design and construction-sized minimum weight/life cycle cost; high voltage transmission (100 Vac RMS); medium voltage array or = 440 Vdc); resonant inversion; transformer rotary joint; high frequency power transmission line or = 20 KHz); energy storage on array side or rotary joint; fully redundant; and 10 year life with minimal replacement and repair.

Using qualitative comparative analysis in a systematic review of a complex intervention.

PubMed

Kahwati, Leila; Jacobs, Sara; Kane, Heather; Lewis, Megan; Viswanathan, Meera; Golin, Carol E

2016-05-04

Systematic reviews evaluating complex interventions often encounter substantial clinical heterogeneity in intervention components and implementation features making synthesis challenging. Qualitative comparative analysis (QCA) is a non-probabilistic method that uses mathematical set theory to study complex phenomena; it has been proposed as a potential method to complement traditional evidence synthesis in reviews of complex interventions to identify key intervention components or implementation features that might explain effectiveness or ineffectiveness. The objective of this study was to describe our approach in detail and examine the suitability of using QCA within the context of a systematic review. We used data from a completed systematic review of behavioral interventions to improve medication adherence to conduct two substantive analyses using QCA. The first analysis sought to identify combinations of nine behavior change techniques/components (BCTs) found among effective interventions, and the second analysis sought to identify combinations of five implementation features (e.g., agent, target, mode, time span, exposure) found among effective interventions. For each substantive analysis, we reframed the review's research questions to be designed for use with QCA, calibrated sets (i.e., transformed raw data into data used in analysis), and identified the necessary and/or sufficient combinations of BCTs and implementation features found in effective interventions. Our application of QCA for each substantive analysis is described in detail. We extended the original review findings by identifying seven combinations of BCTs and four combinations of implementation features that were sufficient for improving adherence. We found reasonable alignment between several systematic review steps and processes used in QCA except that typical approaches to study abstraction for some intervention components and features did not support a robust calibration for QCA. QCA was suitable for use within a systematic review of medication adherence interventions and offered insights beyond the single dimension stratifications used in the original completed review. Future prospective use of QCA during a review is needed to determine the optimal way to efficiently integrate QCA into existing approaches to evidence synthesis of complex interventions.

Broad autism phenotype features of Chinese parents with autistic children and their associations with severity of social impairment in probands.

PubMed

Shi, Li-Juan; Ou, Jian-Jun; Gong, Jing-Bo; Wang, Su-Hong; Zhou, Yuan-Yue; Zhu, Fu-Rong; Liu, Xu-Dong; Zhao, Jing-Ping; Luo, Xue-Rong

2015-07-23

Parents of children with autism have higher rates of broad autism phenotype (BAP) features than parents of typically developing children (TDC) in Western countries. This study was designed to examine the rate of BAP features in parents of children with autism and the relationship between parental BAP and the social impairment of their children in a Chinese sample. A total of 299 families with autistic children and 274 families with TDC participated in this study. Parents were assessed using the Broad Autism Phenotype Questionnaire (BAPQ), which includes self-report, informant-report, and best-estimate versions. Children were assessed using the Chinese version of the Social Responsiveness Scale (SRS). Parents of children with autism were significantly more likely to have BAP features than were parents of TDC; mothers and fathers in families with autistic children had various BAP features. The total scores of the informant and best-estimate BAPQ versions for fathers were significantly associated with their children's SRS total scores in the autism group, whereas the total scores of the three BAPQ versions for mothers were significantly associated with their children's SRS total scores in the TDC group. In the autism group, the total SRS scores of children with "BAP present" parents (informant and best-estimate) were higher than the total SRS scores of children with"BAP absent" parents. In the TDC group, the total SRS scores of children with "BAP present" parents were higher than the total SRS scores of children with"BAP absent" parents (best-estimate). Parents of autistic children were found to have higher rates of BAP than parents of TDC in a sample of Chinese parents. The BAP features of parents are associated with their children's social functioning in both autism families and TDC families, but the patterns of the associations are different.

Computational phenotype discovery using unsupervised feature learning over noisy, sparse, and irregular clinical data.

PubMed

Lasko, Thomas A; Denny, Joshua C; Levy, Mia A

2013-01-01

Inferring precise phenotypic patterns from population-scale clinical data is a core computational task in the development of precision, personalized medicine. The traditional approach uses supervised learning, in which an expert designates which patterns to look for (by specifying the learning task and the class labels), and where to look for them (by specifying the input variables). While appropriate for individual tasks, this approach scales poorly and misses the patterns that we don't think to look for. Unsupervised feature learning overcomes these limitations by identifying patterns (or features) that collectively form a compact and expressive representation of the source data, with no need for expert input or labeled examples. Its rising popularity is driven by new deep learning methods, which have produced high-profile successes on difficult standardized problems of object recognition in images. Here we introduce its use for phenotype discovery in clinical data. This use is challenging because the largest source of clinical data - Electronic Medical Records - typically contains noisy, sparse, and irregularly timed observations, rendering them poor substrates for deep learning methods. Our approach couples dirty clinical data to deep learning architecture via longitudinal probability densities inferred using Gaussian process regression. From episodic, longitudinal sequences of serum uric acid measurements in 4368 individuals we produced continuous phenotypic features that suggest multiple population subtypes, and that accurately distinguished (0.97 AUC) the uric-acid signatures of gout vs. acute leukemia despite not being optimized for the task. The unsupervised features were as accurate as gold-standard features engineered by an expert with complete knowledge of the domain, the classification task, and the class labels. Our findings demonstrate the potential for achieving computational phenotype discovery at population scale. We expect such data-driven phenotypes to expose unknown disease variants and subtypes and to provide rich targets for genetic association studies.

Computational Phenotype Discovery Using Unsupervised Feature Learning over Noisy, Sparse, and Irregular Clinical Data

PubMed Central

Lasko, Thomas A.; Denny, Joshua C.; Levy, Mia A.

2013-01-01

Inferring precise phenotypic patterns from population-scale clinical data is a core computational task in the development of precision, personalized medicine. The traditional approach uses supervised learning, in which an expert designates which patterns to look for (by specifying the learning task and the class labels), and where to look for them (by specifying the input variables). While appropriate for individual tasks, this approach scales poorly and misses the patterns that we don’t think to look for. Unsupervised feature learning overcomes these limitations by identifying patterns (or features) that collectively form a compact and expressive representation of the source data, with no need for expert input or labeled examples. Its rising popularity is driven by new deep learning methods, which have produced high-profile successes on difficult standardized problems of object recognition in images. Here we introduce its use for phenotype discovery in clinical data. This use is challenging because the largest source of clinical data – Electronic Medical Records – typically contains noisy, sparse, and irregularly timed observations, rendering them poor substrates for deep learning methods. Our approach couples dirty clinical data to deep learning architecture via longitudinal probability densities inferred using Gaussian process regression. From episodic, longitudinal sequences of serum uric acid measurements in 4368 individuals we produced continuous phenotypic features that suggest multiple population subtypes, and that accurately distinguished (0.97 AUC) the uric-acid signatures of gout vs. acute leukemia despite not being optimized for the task. The unsupervised features were as accurate as gold-standard features engineered by an expert with complete knowledge of the domain, the classification task, and the class labels. Our findings demonstrate the potential for achieving computational phenotype discovery at population scale. We expect such data-driven phenotypes to expose unknown disease variants and subtypes and to provide rich targets for genetic association studies. PMID:23826094

The MECP2 variant c.925C>T (p.Arg309Trp) causes intellectual disability in both males and females without classic features of Rett syndrome.

PubMed

Schönewolf-Greulich, B; Tejada, M-I; Stephens, K; Hadzsiev, K; Gauthier, J; Brøndum-Nielsen, K; Pfundt, R; Ravn, K; Maortua, H; Gener, B; Martínez-Bouzas, C; Piton, A; Rouleau, G; Clayton-Smith, J; Kleefstra, T; Bisgaard, A-M; Tümer, Z

2016-06-01

Missense MECP2 variants can have various phenotypic effects ranging from a normal phenotype to typical Rett syndrome (RTT). In females, the phenotype can also be influenced by the X-inactivation pattern. In this study, we present detailed clinical descriptions of six patients with a rare base-pair substitution affecting Arg309 at the C-terminal end of the transcriptional repression domain (TRD). All patients have intellectual disability and present with some RTT features, but they do not fulfill the clinical criteria for typical or atypical RTT. Most of the patients also have mild facial dysmorphism. Intriguingly, the mother of an affected male patient is an asymptomatic carrier of this variant. It is therefore likely that the p.(Arg309Trp) variation does not necessarily lead to male lethality, and it results in a wide range of clinical features in females, probably influenced by different X-inactivation patterns in target tissues. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Overview of the observations of symbiotic stars

NASA Technical Reports Server (NTRS)

Viotti, Roberto

1993-01-01

The term Symbiotic stars commonly denotes variable stars whose optical spectra simultaneously present a cool absorption spectrum (typically TiO absorption bands) and emission lines of high ionization energy. This term is now used for the category of variable stars with composite spectrum. The main spectral features of these objects are: (1) the presence of the red continuum typical of a cool star, (2) the rich emission line spectrum, and (3) the UV excess, frequently with the Balmer continuum in emission. In addition to the peculiar spectrum, the very irregular photometric and spectroscopic variability is the major feature of the symbiotic stars. Moreover, the light curve is basic to identify the different phases of activity in a symbiotic star. The physical mechanisms that cause the symbiotic phenomenon and its variety are the focus of this paper. An astronomical phenomenon characterized by a composite stellar spectrum with two apparently conflicting features, and large variability has been observed. Our research set out to find the origin of this behavior and, in particular, to identify and measure the physical mechanism(s) responsible for the observed phenomena.

Highest-weight representations of Brocherd`s algebras

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slansky, R.

1997-01-01

General features of highest-weight representations of Borcherd`s algebras are described. to show their typical features, several representations of Borcherd`s extensions of finite-dimensional algebras are analyzed. Then the example of the extension of affine- su(2) to a Borcherd`s algebra is examined. These algebras provide a natural way to extend a Kac-Moody algebra to include the hamiltonian and number-changing operators in a generalized symmetry structure.

A Novel Real-Time Reference Key Frame Scan Matching Method.

PubMed

Mohamed, Haytham; Moussa, Adel; Elhabiby, Mohamed; El-Sheimy, Naser; Sesay, Abu

2017-05-07

Unmanned aerial vehicles represent an effective technology for indoor search and rescue operations. Typically, most indoor missions' environments would be unknown, unstructured, and/or dynamic. Navigation of UAVs in such environments is addressed by simultaneous localization and mapping approach using either local or global approaches. Both approaches suffer from accumulated errors and high processing time due to the iterative nature of the scan matching method. Moreover, point-to-point scan matching is prone to outlier association processes. This paper proposes a low-cost novel method for 2D real-time scan matching based on a reference key frame (RKF). RKF is a hybrid scan matching technique comprised of feature-to-feature and point-to-point approaches. This algorithm aims at mitigating errors accumulation using the key frame technique, which is inspired from video streaming broadcast process. The algorithm depends on the iterative closest point algorithm during the lack of linear features which is typically exhibited in unstructured environments. The algorithm switches back to the RKF once linear features are detected. To validate and evaluate the algorithm, the mapping performance and time consumption are compared with various algorithms in static and dynamic environments. The performance of the algorithm exhibits promising navigational, mapping results and very short computational time, that indicates the potential use of the new algorithm with real-time systems.

Newly described features resulting from high-magnification dermoscopy of tinea capitis.

PubMed

Lacarrubba, Francesco; Verzì, Anna Elisa; Micali, Giuseppe

2015-03-01

Recent studies have reported "comma hairs" as a typical dermoscopic feature of tinea capitis observed at low magnification (×10). The aim of this study was to evaluate the dermoscopic aspects of tinea capitis at high magnification (×150) and its diagnostic role. Five children (2 boys and 3 girls; aged 4-10 years) with multiple scaly patches of alopecia underwent scalp dermoscopy, direct microscopic examinations, and mycological cultures of skin scrapings. Using low magnification (×30), typical comma hairs, "Morse code-like" hairs, and "zigzag" hairs were observed. When using high magnification (×150), additional features were horizontal white bands that appear as empty bands that are likely related to localized areas of fungal infection. These horizontal white bands are usually multiple and may cause the hair to bend and break. We also identified a new dermoscopic feature consisting of translucent, easily deformable hairs that look weakened and transparent and show unusual bends; they are likely the result of a massive fungal invasion involving the whole hair shaft. Direct microscopic examination showed fungal infection and results of mycological culture were positive for Microsporum canis in all cases. The identification of new findings using higher-magnification dermoscopy may enhance the diagnosis of tinea capitis and be of help to better understand some pathogenetic mechanisms.

76 FR 15798 - Special Conditions: Boeing 747-468, Installation of a Medical Lift

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-22

... a novel or unusual design feature associated with the installation of a medical lift. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These... airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. Type...

Nucleic acid nanomaterials: Silver-wired DNA

NASA Astrophysics Data System (ADS)

Auffinger, Pascal; Ennifar, Eric

2017-10-01

DNA double helical structures are supramolecular assemblies that are typically held together by classical Watson-Crick pairing. Now, nucleotide chelation of silver ions supports an extended silver-DNA hybrid duplex featuring an uninterrupted silver array.

Best practices in developing regional transportation plans

DOT National Transportation Integrated Search

2001-09-01

AltAlthough Regional Transportation Plans (RTPs) have been prepared for many decades, there has been little effort to comprehensively compare and evaluate the different features of these documents. Most Metropolitan Planning Organizations (MPO) typic...

Sclerosing Cholangitis: Clinicopathologic Features, Imaging Spectrum, and Systemic Approach to Differential Diagnosis.

PubMed

Seo, Nieun; Kim, So Yeon; Lee, Seung Soo; Byun, Jae Ho; Kim, Jin Hee; Kim, Hyoung Jung; Lee, Moon-Gyu

2016-01-01

Sclerosing cholangitis is a spectrum of chronic progressive cholestatic liver disease characterized by inflammation, fibrosis, and stricture of the bile ducts, which can be classified as primary and secondary sclerosing cholangitis. Primary sclerosing cholangitis is a chronic progressive liver disease of unknown cause. On the other hand, secondary sclerosing cholangitis has identifiable causes that include immunoglobulin G4-related sclerosing disease, recurrent pyogenic cholangitis, ischemic cholangitis, acquired immunodeficiency syndrome-related cholangitis, and eosinophilic cholangitis. In this review, we suggest a systemic approach to the differential diagnosis of sclerosing cholangitis based on the clinical and laboratory findings, as well as the typical imaging features on computed tomography and magnetic resonance (MR) imaging with MR cholangiography. Familiarity with various etiologies of sclerosing cholangitis and awareness of their typical clinical and imaging findings are essential for an accurate diagnosis and appropriate management.

Application of Mössbauer Spectroscopy in Earth Sciences

NASA Astrophysics Data System (ADS)

Vandenberghe, Robert E.; De Grave, Eddy

Iron being the fourth most abundant element in the earth crust, 57Fe Mössbauer spectroscopy has become a suitable additional technique for the characterization of all kind of soil materials and minerals. However, for that purpose a good knowledge of the spectral behavior of the various minerals is indispensable. In this chapter a review of the most important soil materials and rock-forming minerals is presented. It starts with a description of the Mössbauer spectroscopic features of the iron oxides and hydroxides, which are essentially present in soils and sediments. Further, the Mössbauer spectra from sulfides, sulfates and carbonates are briefly considered. Finally, the Mössbauer features of the typical and most common silicate and phosphate minerals are reported. The chapter ends with some typical examples, illustrating the use and power of Mössbauer spectroscopy in the characterization of minerals.

[Neuropsychiatric aspects of Prader-Willi syndrome – a review].

PubMed

Briegel, Wolfgang

2018-05-01

Prader-Willi Syndrome (PWS) is caused by the absence of paternal expression of imprinted genes in the region at 15q11–q13. With an estimated birth incidence of 1/15 000 – 1/30 000, PWS is one of the more frequent genetic syndromes among humans. Typical physical features include neonatal hypotonia and feeding problems, hypogonadism, hyperphagia in later childhood with consecutive obesity, and short stature. Most people with PWS show a mild to moderate intellectual disability. Furthermore, lability of mood, temper tantrums, skin-picking, and compulsive behaviors are quite typical for subjects with PWS. Psychotic disorders have also been found to be quite common in adulthood. This manuscript reviews current knowledge about the etiology, physical features, developmental aspects, behavioral phenotype, and psychiatric disorders that occur as well as existing psychopharmacological and psychotherapeutic interventions.

Supporting Active Living Through Community Plans: The Association of Planning Documents With Design Standards and Features.

PubMed

Peterson, Erin L; Carlson, Susan A; Schmid, Thomas L; Brown, David R; Galuska, Deborah A

2018-01-01

The purpose of this study was to examine the association between the presence of supportive community planning documents in US municipalities with design standards and requirements supportive of active living. Cross-sectional study using data from the 2014 National Survey of Community-Based Policy and Environmental Supports for Healthy Eating and Active Living. Nationally representative sample of US municipalities. Respondents are 2005 local officials. Assessed: (1) The presence of design standards and feature requirements and (2) the association between planning documents and design standards and feature requirements supportive of active living in policies for development. Using logistic regression, significant trends were identified in the presence of design standards and feature requirements by plan and number of supportive objectives present. Prevalence of design standards ranged from 19% (developer dedicated right-of-way for bicycle infrastructure development) to 50% (traffic-calming features in areas with high pedestrian and bicycle volume). Features required in policies for development ranged from 14% (short/medium pedestrian-scale block sizes) to 44% (minimum sidewalk widths of 5 feet) of municipalities. As the number of objectives in municipal plans increased, there was a significant and positive trend ( P < .05) in the prevalence of each design standard and requirement. Municipal planning documents containing objectives supportive of physical activity are associated with design standards and feature requirements supportive of activity-friendly communities.

Progressive aphasia secondary to Alzheimer disease pathology: A clinicopathologic and MRI study

PubMed Central

Josephs, Keith A.; Whitwell, Jennifer L.; Duffy, Joseph R.; Vanvoorst, Wendy A.; Strand, Edyth A.; Hu, William T.; Boeve, Bradley F.; Graff-Radford, Neill R.; Parisi, Joseph E.; Knopman, David S.; Dickson, Dennis W.; Jack, Clifford R.; Petersen, Ronald C.

2009-01-01

Background The pathology causing progressive aphasia is typically a variant of frontotemporal lobar degeneration, especially with ubiquitin-positive-inclusions (FTLD-U). Less commonly the underlying pathology is Alzheimer disease (AD). Objective To compare clinicopathological and MRI features of subjects with progressive aphasia and AD pathology, to subjects with aphasia and FTLD-U pathology, and subjects with typical AD. Methods We identified 5 subjects with aphasia and AD pathology and 5 with aphasia and FTLD-U pathology with an MRI from a total of 216 aphasia subjects. Ten subjects with typical AD clinical features and AD pathology were also identified. All subjects with AD pathology underwent pathological re-analysis with TDP-43 immunohistochemistry. Voxel-based morphometry (VBM) was used to assess patterns of grey matter atrophy in the aphasia cases with AD pathology, aphasia cases with FTLD-U, and typical AD cases with AD pathology, compared to a normal control group. Results All aphasic subjects had fluent speech output. However, those with AD pathology had better processing speed than those with FTLD-U pathology. Immunohistochemistry with TDP-43 antibodies was negative. VBM revealed grey matter atrophy predominantly in the temporoparietal cortices with notable sparing of the hippocampus in the aphasia with AD subjects. In comparison, the aphasic subjects with FTLD-U showed sparing of the parietal lobe. Typical AD subjects showed temporoparietal and hippocampal atrophy. Conclusions A temporoparietal pattern of atrophy on MRI in patients with progressive fluent aphasia and relatively preserved processing speed is suggestive of underlying AD pathology rather than FTLD-U. PMID:18166704

The Efficacy of Acute Electroconvulsive Therapy in Atypical Depression

PubMed Central

Husain, Mustafa M.; McClintock, Shawn M.; Rush, A. John; Knapp, Rebecca G.; Fink, Max; Rummans, Teresa A.; Rasmussen, Keith; Claassen, Cynthia; Petrides, Georgios; Biggs, Melanie M.; Mueller, Martina; Sampson, Shirlene; Bailine, Samuel H.; Lisanby, Sarah H.; Kellner, Charles H.

2013-01-01

Objective This study examined the characteristics and outcomes of patients with major depressive disorder (MDD), with or without atypical features, who were treated with acute bilateral electroconvulsive therapy (ECT). Method Analyses were conducted with 489 patients who met DSM-IV criteria for MDD. Subjects were identified as typical or atypical on the basis of the Structured Clinical Interview for DSM-IV obtained at baseline prior to ECT. Depression symptom severity was measured by the 24-item Hamilton Rating Scale for Depression (HAM-D24) and the 30-item Inventory of Depressive Symptomatology–Self-Report (IDS-SR30). Remission was defined as at least a 60% decrease from baseline in HAM-D24 score and a total score of 10 or below on the last 2 consecutive HAM-D24 ratings. The randomized controlled trial was performed from 1997 to 2004. Results The typical (N = 453) and atypical (N = 36) groups differed in several sociodemographic and clinical variables including gender (p = .0071), age (p = .0005), treatment resistance (p = .0014), and age at first illness onset (p < .0001) and onset of current episode (p = .0008). Following an acute course of bilateral ECT, a considerable portion of both the typical (67.1%) and the atypical (80.6%) groups reached remission. The atypical group was 2.6 (95% CI = 1.1 to 6.2) times more likely to remit than the typical group after adjustment for age, psychosis, gender, clinical site, and depression severity based on the HAM-D24. Conclusion Acute ECT is an efficacious treatment for depressed patients with typical or atypical symptom features. PMID:18278988

Endemic chronic kidney disease of unknown etiology in Sri Lanka: Correlation of pathology with clinical stages

PubMed Central

Wijetunge, S.; Ratnatunga, N. V. I.; Abeysekera, T. D. J.; Wazil, A. W. M.; Selvarajah, M.

2015-01-01

Chronic kidney disease of unknown etiology (CKDU) is endemic among the rural farming communities in several localities in and around the North Central region of Sri Lanka. This is an interstitial type renal disease and typically has an insidious onset and slow progression. This study was conducted to identify the pathological features in the different clinical stages of CKDU. This is a retrospective study of 251 renal biopsies identified to have a primary interstitial disease from regions endemic for CKDU. Pathological features were assessed and graded in relation to the clinical stage. The mean age of those affected by endemic CKDU was 37.3 ± 12.5 years and the male to female ratio was 3.3:1. The predominant feature of stage I disease was mild and moderate interstitial fibrosis; most did not have interstitial inflammation. The typical stage II disease had moderate interstitial fibrosis with or without mild interstitial inflammation. Stage III disease had moderate and severe interstitial fibrosis, moderate interstitial inflammation, tubular atrophy and some glomerulosclerosis. Stage IV disease typically had severe interstitial fibrosis and inflammation, tubular atrophy and glomerulosclerosis. The mean age of patients with stage I disease (27 ± 10.8 years) was significantly lower than those of the other stages. About 79.2%, 55%, 49.1% and 50% in stage I, II, III and IV disease respectively were asymptomatic at the time of biopsy. PMID:26628792

GATOR: Requirements capturing of telephony features

NASA Technical Reports Server (NTRS)

Dankel, Douglas D., II; Walker, Wayne; Schmalz, Mark

1992-01-01

We are developing a natural language-based, requirements gathering system called GATOR (for the GATherer Of Requirements). GATOR assists in the development of more accurate and complete specifications of new telephony features. GATOR interacts with a feature designer who describes a new feature, set of features, or capability to be implemented. The system aids this individual in the specification process by asking for clarifications when potential ambiguities are present, by identifying potential conflicts with other existing features, and by presenting its understanding of the feature to the designer. Through user interaction with a model of the existing telephony feature set, GATOR constructs a formal representation of the new, 'to be implemented' feature. Ultimately GATOR will produce a requirements document and will maintain an internal representation of this feature to aid in future design and specification. This paper consists of three sections that describe (1) the structure of GATOR, (2) POND, GATOR's internal knowledge representation language, and (3) current research issues.