Interdiffusion behavior of U3Si2 with FeCrAl via diffusion couple studies

NASA Astrophysics Data System (ADS)

Hoggan, Rita E.; He, Lingfeng; Harp, Jason M.

2018-04-01

Uranium silicide (U3Si2) is a candidate to replace uranium oxide (UO2) as light water reactor (LWR) fuel because of its higher thermal conductivity and higher fissile density relative to the current standard, UO2. A class of Fe, Cr, Al alloys collectively known as FeCrAl alloys that have superior mechanical and oxidation resistance are being considered as an alternative to the standard Zirconium based LWR cladding. The interdiffusion behavior between FeCrAl and U3Si2 is investigated in this study. Commercially available FeCrAl, along with U3Si2 pellets were placed in diffusion couples. Individual tests were ran at temperatures ranging from 500 °C to 1000 °C for 30 h and 100 h. The interdiffusion was analyzed with an optical microscope, scanning electron microscope, and transmission electron microscope. Uniform and planar interdiffusion layers along the material interface were illustrated with backscatter electron micrographs and energy-dispersive X-ray spectroscopy. Electron diffraction was used to validate phases present in the system, including distinct U2Fe3Si/UFe2 and UFeSi layers at the material interface. U and Fe diffused far into the FeCrAl and U3Si2 matrix, respectively, in the higher temperature tests. No interaction was observed at 500 °C for 30 h.

Experimental investigation of the phase equilibria and thermodynamic assessment in the U-Ga and U-Al-Ga systems

NASA Astrophysics Data System (ADS)

Moussa, Chantal; Berche, Alexandre; Barbosa, José; Pasturel, Mathieu; Stepnik, Bertrand; Tougait, Olivier

2018-02-01

The phase relations in the binary U-Ga and ternary U-Al-Ga systems were established as an isopleth section and two isothermal sections at 900 K and 1150 K for the whole concentration range, respectively. They were experimentally determined by means of powder and single crystal XRD, SEM-EDS analyses on both as-cast and heat-treated samples and DTA measurements. Both systems were thermodynamically assessed using the Calphad method based on the available data, i.e. phase relations and thermodynamic properties. The new description of the U-Ga phase diagram improves the composition-temperature description for most of invariant reactions. The U-Al-Ga system is characterized by large ternary extensions of the binary phases and the absence of ternary intermediate phase at both 900 K and 1150 K. These experimental results are nicely reproduced by the Calphad assessment, allowing to extract the thermodynamic parameters further used to calculate the liquidus projection and the invariant reactions along with their temperature.

Role of Si on the Diffusional Interactions Between U-Mo and Al-Si Alloys at 823 K (550 °C)

NASA Astrophysics Data System (ADS)

Perez, Emmanuel; Sohn, Yong-Ho; Keiser, Dennis D.

2013-01-01

U-Mo dispersions in Al-alloy matrix and monolithic fuels encased in Al-alloy are under development to fulfill the requirements for research and test reactors to use low-enriched molybdenum stabilized uranium alloy fuels. Significant interaction takes place between the U-Mo fuel and Al during manufacturing and in-reactor irradiation. The interaction products are Al-rich phases with physical and thermal characteristics that adversely affect fuel performance and result in premature failure. Detailed analysis of the interdiffusion and microstructural development of this system was carried through diffusion couples consisting of U-7 wt pct Mo, U-10 wt pct Mo and U-12 wt pct Mo in contact with pure Al, Al-2 wt pct Si, and Al-5 wt pct Si, annealed at 823 K (550 °C) for 1, 5 and 20 hours. Scanning electron microscopy and transmission electron microscopy were employed for the analysis. Diffusion couples consisting of U-Mo in contact with pure Al contained UAl3, UAl4, U6Mo4Al43, and UMo2Al20 phases. Additions of Si to the Al significantly reduced the thickness of the interdiffusion zone. The interdiffusion zones developed Al- and Si-enriched regions, whose locations and size depended on the Si and Mo concentrations in the terminal alloys. In these couples, the (U,Mo)(Al,Si)3 phase was observed throughout the interdiffusion zone, and the U6Mo4Al43 and UMo2Al20 phases were observed only where the Si concentrations were low.

Phase development in a U-7 wt.% Mo vs. Al-7 wt.% Ge diffusion couple

NASA Astrophysics Data System (ADS)

Perez, E.; Keiser, D. D.; Sohn, Y. H.

2013-10-01

Fuel development for the Reduced Enrichment for Research and Test Reactors (RERTR) program has demonstrated that U-Mo alloys in contact with Al develop interaction regions with phases that have poor irradiation behavior. The addition of Si to the Al has been considered with positive results. In this study, compositional modification is considered by replacing Si with Ge to determine the effect on the phase development in the system. The microstructural and phase development of a diffusion couple of U-7 wt.% Mo in contact with Al-7 wt.% Ge was examined by transmission electron microscopy, scanning electron microscopy and energy dispersive spectroscopy. The interdiffusion zone developed a microstructure that included the cubic-UGe3 phase and amorphous phases. The UGe3 phase was observed with and without Mo and Al solid solution developing a (U,Mo)(Al,Ge)3 phase.

Radiation Resistance of the U(Al, Si)3 Alloy: Ion-Induced Disordering

PubMed Central

Yaniv, Gili; Horak, Pavel; Vacik, Jiri; Mykytenko, Natalia; Rafailov, Gennady; Dahan, Itzchak; Fuks, David; Kiv, Arik

2018-01-01

During the exploitation of nuclear reactors, various U-Al based ternary intermetallides are formed in the fuel-cladding interaction layer. Structure and physical properties of these intermetallides determine the radiation resistance of cladding and, ultimately, the reliability and lifetime of the nuclear reactor. In current research, U(Al, Si)3 composition was studied as a potential constituent of an interaction layer. Phase content of the alloy of an interest was ordered U(Al, Si)3, structure of which was reported earlier, and pure Al (constituting less than 20 vol % of the alloy). This alloy was investigated prior and after the irradiation performed by Ar ions at 30 keV. The irradiation was performed on the transmission electron microscopy (TEM, JEOL, Japan) samples, characterized before and after the irradiation process. Irradiation induced disorder accompanied by stress relief. Furthermore, it was found that there is a dose threshold for disordering of the crystalline matter in the irradiated region. Irradiation at doses equal or higher than this threshold resulted in almost solely disordered phase. Using the program “Stopping and Range of Ions in Matter” (SRIM), the parameters of penetration of Ar ions into the irradiated samples were estimated. Based on these estimations, the dose threshold for ion-induced disordering of the studied material was assessed. PMID:29393870

Radiation Resistance of the U(Al, Si)₃ Alloy: Ion-Induced Disordering.

PubMed

Meshi, Louisa; Yaniv, Gili; Horak, Pavel; Vacik, Jiri; Mykytenko, Natalia; Rafailov, Gennady; Dahan, Itzchak; Fuks, David; Kiv, Arik

2018-02-02

During the exploitation of nuclear reactors, various U-Al based ternary intermetallides are formed in the fuel-cladding interaction layer. Structure and physical properties of these intermetallides determine the radiation resistance of cladding and, ultimately, the reliability and lifetime of the nuclear reactor. In current research, U(Al, Si)₃ composition was studied as a potential constituent of an interaction layer. Phase content of the alloy of an interest was ordered U(Al, Si)₃, structure of which was reported earlier, and pure Al (constituting less than 20 vol % of the alloy). This alloy was investigated prior and after the irradiation performed by Ar ions at 30 keV. The irradiation was performed on the transmission electron microscopy (TEM, JEOL, Japan) samples, characterized before and after the irradiation process. Irradiation induced disorder accompanied by stress relief. Furthermore, it was found that there is a dose threshold for disordering of the crystalline matter in the irradiated region. Irradiation at doses equal or higher than this threshold resulted in almost solely disordered phase. Using the program "Stopping and Range of Ions in Matter" (SRIM), the parameters of penetration of Ar ions into the irradiated samples were estimated. Based on these estimations, the dose threshold for ion-induced disordering of the studied material was assessed.

Uranium isotopic compositions of the crust and ocean: Age corrections, U budget and global extent of modern anoxia

NASA Astrophysics Data System (ADS)

Tissot, François L. H.; Dauphas, Nicolas

2015-10-01

the variability of the 238U/235U ratio on Pb-Pb and U-Pb ages and provide analytical formulas to calculate age corrections as a function of the age and isotopic composition of the sample. The crustal ratio may be used in calculation of Pb-Pb and U-Pb ages of continental crust rocks and minerals when the U isotopic composition is unknown. In cosmochemistry, the search for 247Cm (t1/2 = 15.6 Myr), an extinct short-lived radionuclide that decays into 235U, is important for understanding how r-process nuclides were synthesized in stars and learning about the astrophysical context of solar system formation (Chen and Wasserburg, 1981; Wasserburg et al., 1996; Nittler and Dauphas, 2006; Brennecka et al., 2010b; Tissot et al., 2015).para> In both terrestrial and extraterrestrial samples, variations in the 238U/235U ratio affect Pb-Pb ages (and depending on the analytical protocols, U-Pb ages). Therefore, samples dated by these techniques need to have their U isotopic compositions measured (Stirling et al., 2005, 2006; Weyer et al., 2008; Amelin et al., 2010; Brennecka et al., 2010b; Brennecka and Wadhwa, 2012; Connelly et al., 2012; Goldmann et al., 2015) or uncertainties on the U isotopic composition should be propagated into age calculations.para> In low temperature aqueous geochemistry, U isotopic fractionation between U4+ and U6+ (driven in part by nuclear field shift effects; Bigeleisen, 1996; Schauble, 2007; Abe et al., 2008), makes U isotopes potential tracers of paleoredox conditions (Montoya-Pino et al., 2010; Brennecka et al., 2011a; Kendall et al., 2013, 2015; Asael et al., 2013; Andersen et al., 2014; Dahl et al., 2014; Goto et al., 2014; Noordmann et al., 2015).para> para>The present paper aims at constraining some aspects of the global budget of uranium in the modern oceans using 238U/235U isotope variations, which involves characterizing the U isotopic composition of seawater and several reservoirs involved in the uranium oceanic budget

Strongly correlated electron behavior in single crystalline U2Os3Al9

NASA Astrophysics Data System (ADS)

Kumar, Neeraj; Das, Pranab Kumar; Kulkarni, Ruta; Thamizhavel, A.; Dhar, S. K.

2012-12-01

We report the magnetic properties of a single crystal of a new compound U2Os3Al9 which crystallizes in the well known Y2Co3Ga9 type orthorhombic structure with space group Cmcm. The susceptibility of U2Os3Al9 shows a peak at 7 K typical of antiferromagnetic ordering. The susceptibility in the paramagnetic state is anisotropic, the easy axis of magnetization lying in the ab-plane of the orthorhombic crystal lattice. The magnetization at 2 K, measured up to a maximum field of 160 kOe, shows a metamagnetic transition near 118 kOe when the field is aligned along [010] in addition to a small metamagnetic transition near 25 kOe. The bulk antiferromagnetic ordering of the uranium ions at TN = 7 K is confirmed by a peak in the heat capacity with ΔC nearly 7 J/U.mol K. An extrapolation of the heat capacity data from the paramagnetic regime to T = 0 gives an enhanced electronic specific heat coefficient of 120 mJ/U.mol K2. The electrical resistivity of U2Os3Al9 shows a negative temperature coefficient between 300 and TN which is a signature of spin fluctuations in a narrow band or a Kondo type of interaction. The data thus suggest the presence of strong electron correlations in this compound.

Evidence of mixed valence states in U M2Al 3 ( M = Ni, Pd) studied by X-ray photoemission spectroscopy

NASA Astrophysics Data System (ADS)

Fujimori, Shin-ichi; Saito, Yasuharu; Sato, Noriaki; Komatsubara, Takemi; Suzuki, Shoji; Sato, Shigeru; Ishii, Takehiko

1998-01-01

We have measured the XPS valence band and core-level spectra of U M2Al 3 ( M = Ni and Pd). The results are compared with those of reference materials, dilute alloy U 0.1La 0.9Pd 2Al 3 and itinerant 5 f compound URh 3. The similarity of the core-level spectra between UPd 2Al 3 and U 0.1La 0.9Pd 2Al 3 suggests that their core-level spectra are governed by the interaction between U 5 f and ligand states of neighboring palladium and aluminum sites, with negligible contributions from neighboring uranium states. A complex satellite structure, observed in the core-level spectra of U M2Al 3, suggests that the uranium atoms are in the strong mixed valence states with 5 f2(U 4+) and 5 f3(U 3+).

Enhanced adsorption of U(VI) and 241Am(III) from wastewater using Ca/Al layered double hydroxide@carbon nanotube composites.

PubMed

Chen, Haijun; Chen, Zhe; Zhao, Guixia; Zhang, Zhibin; Xu, Chao; Liu, Yunhai; Chen, Jing; Zhuang, Li; Haya, Tasawar; Wang, Xiangke

2018-04-05

Ca/Al layered double hydroxide decorated carbon nanotube (Ca/Al-LDH@CNTs) composites were fabricated by co-precipitation method and hydrothermal aged treatment. The prepared Ca/Al-LDH@CNTs was characterized by SEM, TEM, EDS, XRD, FT-IR, UV-vis and XPS techniques, and applied to remove U(VI) from aqueous solutions under various environmental conditions (i.e., pH, ionic strength, temperature and contact time). The results indicated that the adsorption of U(VI) on Ca/Al-LDH@CNTs was four times higher than that of U(VI) on bare CNTs. The kinetic investigations reflected the chemisorption of U(VI) on Ca/Al-LDH@CNTs through oxygen-containing functional groups. The adsorption isotherms demonstrated that the adsorption of U(VI) was well fitted by Langmuir model and the maximum adsorption capacity of U(VI) on Ca/Al-LDH@CNTs was calculated to be 382.9 mg g -1 at 289.15 K. The thermodynamic parameters calculated from temperature-dependent isotherms suggested that U(VI) adsorption on Ca/Al-LDH@CNTs were endothermic and spontaneous process. Furthermore, Ca/Al-LDH@CNTs could remove ∼91% of 241 Am(III) at pH = 8.0, which confirmed Ca/Al-LDH@CNTs as a promising material for multiply low level radionuclides' pollution remediation. Copyright © 2017 Elsevier B.V. All rights reserved.

EXPERIENCIAS RELACIONADAS A UNA INTERVENCIÓN PARA REDUCIR EL ESTIGMA RELACIONADO AL VIH/SIDA ENTRE ESTUDIANTES DE MEDICINA EN PUERTO RICO

PubMed Central

Cintrón-Bou, Francheska; Varas-Díaz, Nelson; Marzán-Rodríguez, Melissa; Neilands, Torsten B.

2016-01-01

Existe estigma relacionado al VIH. A las personas con VIH/SIDA-PCVS se les viola sus derechos y obstaculiza su bienestar mental/físico. Profesionales de la salud-PS son fuente de apoyo primordial, sin embargo estos/as le estigmatizan. Es útil adiestrar a PS en relación al estigma social. Implantamos la intervención para reducir el estigma relacionado al VIH/SIDA con 507 estudiantes de medicina. Resultó ser una intervención efectiva, hubo reducción en los niveles de estigma a partir de nuestra intervención y diferencias significativas con el grupo control (p≤.05). Generar espacios de adiestramiento para atender el estigma relacionado al VIH/SIDA es pertinente para la psicología comunitaria porque colaboramos en la reducción de actitudes estigmatizantes que afectan adversamente la prevención de nuevas infecciones, la adherencia al tratamiento antirretroviral y la calidad de vida. PMID:27829690

Crystal structure and physical properties of a novel Kondo antiferromagnet: U3Ru4Al12

NASA Astrophysics Data System (ADS)

Pasturel, M; Tougait, O; Potel, M; Roisnel, T; Wochowski, K; Noël, H; Troć, R

2009-03-01

A novel ternary compound U3Ru4Al12 has been identified in the U-Ru-Al ternary diagram. Single-crystal x-ray diffraction indicates a hexagonal Gd3Ru4Al12-type structure for this uranium-based intermetallic. While this structure type usually induces geometrically a spin-glass behaviour, an antiferromagnetic ordering is observed at TN = 8.4 K in the present case. The reduced effective magnetic moment of U atoms (μeff = 2.6 µB) can be explained by Kondo-like interactions and crystal field effects that have been identified by a logarithmic temperature dependence of the electrical resistivity, negative values of the magnetoresistivity and particular shape of the Seebeck coefficient.

Summary of Independent Assessment of U.S. Government Efforts against Al-Qaeda

DTIC Science & Technology

2017-10-01

Qaeda, and countering terrorism in general • The U.S. has established key partnerships and worked cooperatively with countries around the world...countering terrorism before the forces tasked with these missions reach a breaking point. Requirements for dismantling Al-Qaeda If the U.S. government...International Development’s Office of Transition Initiatives, and the Department of the Treasury’s Office of Terrorism and Financial Intelligence. o

Effect of stress evolution on microstructural behavior in U-Mo/Al dispersion fuel [Effect of stress on microstructural evolution in U-Mo/Al dispersion fuel

DOE PAGES

Jeong, G. Y.; Kim, Yeon Soo; Jamison, L. M.; ...

2017-02-20

U-Mo/Al dispersion fuel irradiated to high burnup at high power (high fission rate) exhibited microstructural changes such as deformation of the fuel particles, pore growth, and rupture of the Al matrix. The driving force for these microstructural changes was meat swelling caused by a combination of fuel particle swelling and interaction layer growth. Five miniplates with well-recorded fabrication data and irradiation conditions were selected, and their PIE data was analyzed. ABAQUS finite element analysis (FEA) was utilized to simulate the microstructural evolution of the plates. Using the simulation results shear stress, effective stress and hydrostatic stress exerted on both themore » fuel particles and the Al matrix were determined. The effects of fabrication and irradiation variables on stress-induced microstructural evolutions, such as pore growth in the interaction layers and Al matrix rupture, were investigated. The observed microstructural changes were consistent with the calculated stress distribution in the meat.« less

Effect of stress evolution on microstructural behavior in U-Mo/Al dispersion fuel [Effect of stress on microstructural evolution in U-Mo/Al dispersion fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeong, G. Y.; Kim, Yeon Soo; Jamison, L. M.

U-Mo/Al dispersion fuel irradiated to high burnup at high power (high fission rate) exhibited microstructural changes such as deformation of the fuel particles, pore growth, and rupture of the Al matrix. The driving force for these microstructural changes was meat swelling caused by a combination of fuel particle swelling and interaction layer growth. Five miniplates with well-recorded fabrication data and irradiation conditions were selected, and their PIE data was analyzed. ABAQUS finite element analysis (FEA) was utilized to simulate the microstructural evolution of the plates. Using the simulation results shear stress, effective stress and hydrostatic stress exerted on both themore » fuel particles and the Al matrix were determined. The effects of fabrication and irradiation variables on stress-induced microstructural evolutions, such as pore growth in the interaction layers and Al matrix rupture, were investigated. The observed microstructural changes were consistent with the calculated stress distribution in the meat.« less

Crystallographic study of Si and ZrN coated U-Mo atomised particles and of their interaction with al under thermal annealing

NASA Astrophysics Data System (ADS)

Zweifel, T.; Palancher, H.; Leenaers, A.; Bonnin, A.; Honkimaki, V.; Tucoulou, R.; Van Den Berghe, S.; Jungwirth, R.; Charollais, F.; Petry, W.

2013-11-01

A new type of high density fuel is needed for the conversion of research and test reactors from high to lower enriched uranium. The most promising one is a dispersion of atomized uranium-molybdenum (U-Mo) particles in an Al matrix. However, during in-pile irradiation the growth of an interaction layer between the U-Mo and the Al matrix strongly limits the fuel's performance. To improve the in-pile behaviour, the U-Mo particles can be coated with protective layers. The SELENIUM (Surface Engineering of Low ENrIched Uranium-Molybdenum) fuel development project consists of the production, irradiation and post-irradiation examination of 2 flat, full-size dispersion fuel plates containing respectively Si and ZrN coated U-Mo atomized powder dispersed in a pure Al matrix. In this paper X-ray diffraction analyses of the Si and ZrN layers after deposition, fuel plate manufacturing and thermal annealing are reported. It was found for the U-Mo particles coated with ZrN (thickness 1 μm), that the layer is crystalline, and exhibits lower density than the theoretical one. Fuel plate manufacturing does not strongly influence these crystallographic features. For the U-Mo particles coated with Si (thickness 0.6 μm), the measurements of the as received material suggest an amorphous state of the deposited layer. Fuel plate manufacturing strongly modifies its composition: Si reacts with the U-Mo particles and the Al matrix to grow U(Al, Si)3 and U3Si5 phases. Finally both coatings have shown excellent performances under thermal treatment by limiting drastically the U-Mo/Al interdiffusion. U(Al,Si)3 with two lattice parameters (4.16 Å and 4.21 Å), A distorted U3Si5 phase. Note that these phases were not present in the U-Mo(Si) powders. These phases are usually found in the Silicon rich diffusion layer (SiRDL) obtained in dispersed fuels (as-manufactured U-Mo/Al(Si) fuel plates [12,3] or annealed UMo(Si)/Al fuel rods [40]) as well as in diffusion couples (U-Mo/Al(Si7) [37-39] or U

Prediction of U-Mo dispersion nuclear fuels with Al-Si alloy using artificial neural network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Susmikanti, Mike, E-mail: mike@batan.go.id; Sulistyo, Jos, E-mail: soj@batan.go.id

2014-09-30

Dispersion nuclear fuels, consisting of U-Mo particles dispersed in an Al-Si matrix, are being developed as fuel for research reactors. The equilibrium relationship for a mixture component can be expressed in the phase diagram. It is important to analyze whether a mixture component is in equilibrium phase or another phase. The purpose of this research it is needed to built the model of the phase diagram, so the mixture component is in the stable or melting condition. Artificial neural network (ANN) is a modeling tool for processes involving multivariable non-linear relationships. The objective of the present work is to developmore » code based on artificial neural network models of system equilibrium relationship of U-Mo in Al-Si matrix. This model can be used for prediction of type of resulting mixture, and whether the point is on the equilibrium phase or in another phase region. The equilibrium model data for prediction and modeling generated from experimentally data. The artificial neural network with resilient backpropagation method was chosen to predict the dispersion of nuclear fuels U-Mo in Al-Si matrix. This developed code was built with some function in MATLAB. For simulations using ANN, the Levenberg-Marquardt method was also used for optimization. The artificial neural network is able to predict the equilibrium phase or in the phase region. The develop code based on artificial neural network models was built, for analyze equilibrium relationship of U-Mo in Al-Si matrix.« less

Annealing tests of in-pile irradiated oxide coated U-Mo/Al-Si dispersed nuclear fuel

NASA Astrophysics Data System (ADS)

Zweifel, T.; Valot, Ch.; Pontillon, Y.; Lamontagne, J.; Vermersch, A.; Barrallier, L.; Blay, T.; Petry, W.; Palancher, H.

2014-09-01

U-Mo/Al based nuclear fuels have been worldwide considered as a promising high density fuel for the conversion of high flux research reactors from highly enriched uranium to lower enrichment. In this paper, we present the annealing test up to 1800 °C of in-pile irradiated U-Mo/Al-Si fuel plate samples. More than 70% of the fission gases (FGs) are released during two major FG release peaks around 500 °C and 670 °C. Additional characterisations of the samples by XRD, EPMA and SEM suggest that up to 500 °C FGs are released from IDL/matrix interfaces. The second peak at 670 °C representing the main release of FGs originates from the interaction between U-Mo and matrix in the vicinity of the cladding.

Post-irradiation examination of prototype Al-64 wt% U{sub 3}Si{sub 2} fuel rods from NRU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sears, D.F.; Primeau, M.F.; Buchanan, C.

1997-08-01

Three prototype fuel rods containing Al-64 wt% U{sub 3}Si{sub 2} (3.15 gU/cm{sup 3}) have been irradiated to their design burnup in the NRU reactor without incident. The fuel was fabricated using production-scale equipment and processes previously developed for Al-U{sub 3}Si fuel fabrication at Chalk River Laboratories, and special equipment developed for U{sub 3}Si{sub 2} powder production and handling. The rods were irradiated in NRU up to 87 at% U-235 burnup under typical driver fuel conditions; i.e., nominal coolant inlet temperature 37{degrees}C, inlet pressure 654 kPa, mass flow 12.4 L/s, and element linear power ratings up to 73 kW/m. Post-irradiation examinationsmore » showed that the fuel elements survived the irradiation without defects. Fuel core diametral increases and volumetric swelling were significantly lower than that of Al-61 wt% U{sub 3}Si fuel irradiated under similar conditions. This irradiation demonstrated that the fabrication techniques are adequate for full-scale fuel manufacture, and qualified the fuel for use in AECL`s research reactors.« less

POLLUTION PREVENTION OPPORTUNITY ASSESSMENT - U.S. COAST GUARD AVIATION TRAINING CENTER - MOBILE, AL

EPA Science Inventory

An assessment of pollution prevention opportunities at the U.S. Coast Guard Aviation Training Center in Mobile, AL, identified waste reduction opportunities in five major processing areas: flight simulator operation, aircraft maintenance, aircraft fueling, aircraft washing, and...

Evaluation of thermochemical biomass conversion in fluidized bed =

NASA Astrophysics Data System (ADS)

Neves, Daniel dos Santos Felix das

Dado o aumento acelerado dos precos dos combustiveis fosseis e as incertezas quanto a sua disponibilidade futura, tem surgido um novo interesse nas tecnologias da biomassa aplicadas a producao de calor, eletricidade ou combustiveis sinteticos. Nao obstante, para a conversao termoquimica de uma particula de biomassa solida concorrem fenomenos bastante complexos que levam, em primeiro lugar, a secagem do combustivel, depois a pirolise e finalmente a combustao ou gasificacao propriamente ditas. Uma descricao relativamente incompleta de alguns desses estagios de conversao constitui ainda um obstaculo ao desenvolvimento das tecnologias que importa ultrapassar. Em particular, a presenca de elevados conteudos de materia volatil na biomassa poe em evidencia o interesse pratico do estudo da pirolise. A importância da pirolise durante a combustao de biomassa foi evidenciada neste trabalho atraves de ensaios realizados num reator piloto de leito fluidizado borbulhante. Verificou-se que o processo ocorre em grande parte a superficie do leito com chamas de difusao devido a libertacao de volateis, o que dificulta o controlo da temperatura do reator acima do leito. No caso da gasificacao de biomassa a pirolise pode inclusivamente determinar a eficiencia quimica do processo. Isso foi mostrado neste trabalho durante ensaios de gasificacao num reator de leito fluidizado de 2MWth, onde um novo metodo de medicao permitiu fechar o balanco de massa ao gasificador e monitorizar o grau de conversao da biomassa. A partir destes resultados tornou-se clara a necessidade de descrever adequadamente a pirolise de biomassa com vista ao projeto e controlo dos processos. Em aplicacoes de engenharia ha particular interesse na estequiometria e propriedades dos principais produtos piroliticos. Neste trabalho procurou-se responder a esta necessidade, inicialmente atraves da estruturacao de dados bibliograficos sobre rendimentos de carbonizado, liquidos piroliticos e gases, assim como composicoes

Summary of FY17 ParaChoice Accomplishments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levinson, Rebecca Sobel; West, Todd H.

As part of analysis support for FCTO, Sandia assesses the factors that influence the future of FCEVs and Hydrogen in the US vehicle fleet. Using ParaChoice, we model competition between FCEVs, conventional vehicles, and other alternative vehicle technologies in order to understand the drivers and sensitivities of adoption of FCEVs. ParaChoice leverages existing tools such as Autonomie (Moawad et al., 2016), AEO (U.S. Energy Information Administration, 2016), and the Macro System Model (Ruth et al., 2009) in order to synthesize a complete picture of the co-evolution of vehicle technology development, energy price evolution, and hydrogen production and pricing, with consumermore » demand for vehicles and fuel. We then assess impacts of FCEV market penetration and hydrogen use on green- house gas (GHG) emissions and petroleum consumption, providing context for the role of policy, technology development, infrastructure, and consumer behavior on the vehicle and fuel mix through parametric and sensitivity analyses.« less

Landscape types and pH control organic matter mediated mobilization of Al, Fe, U and La in boreal catchments

NASA Astrophysics Data System (ADS)

Köhler, Stephan J.; Lidman, Fredrik; Laudon, Hjalmar

2014-06-01

In this study we present data from a seven-year time series from 15 nested streams within a 68 km2 catchment, covering a pH gradient of almost three units. We demonstrate that the two landscape types, forest and wetlands, control the relative mobilization of Al and Fe in this boreal landscape. The La/U ratio is almost constant across the whole catchment despite large variations in pH, Al/Fe and TOC, whereas U and La mobilization increases with increasing contribution of deeper soils and groundwater further downstream. High Al/TOC ratios in the forested catchments suggest that Al originates from the underlying mineral soils, and low Al/TOC ratios derive from wetlands where Al is retained. We observe a competition effect on the binding to TOC between Al and La and also that the relationship between TOC, Al and La changes from the smaller (0.05-2 km2) catchments to larger (3-68 km2) downstream locations. As pH increase downstream, Al and Fe are gradually removed from the aqueous phase by precipitation of particulate gibbsite-like phases and ferrihydrite. This selective removal of Al and Fe from TOC binding sites results in higher La, and U concentrations downstream. Observed element patterns (U, La) and the range of upper continental crust normalized (La/Nd)UCC and (La/Yb)UCC in the near stream, riparian zone were very similar to the observed ratios across the whole catchment. The rising (La/Nd)UCC over (La/Yb)UCC may be due to a selective removal of REE binding to ferrihydrate in the riparian soil, the result of two distinctly different end-members but most probably not due to the in-stream precipitation of ferrihydrate or gibbsite-like phases.

Sensitivity analysis of FeCrAl cladding and U3Si2 fuel under accident conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gamble, Kyle Allan Lawrence; Hales, Jason Dean

2016-08-01

The purpose of this milestone report is to highlight the results of sensitivity analyses performed on two accident tol- erant fuel concepts: U3Si2 fuel and FeCrAl cladding. The BISON fuel performance code under development at Idaho National Laboratory was coupled to Sandia National Laboratories’ DAKOTA software to perform the sensitivity analyses. Both Loss of Coolant (LOCA) and Station blackout (SBO) scenarios were analyzed using main effects studies. The results indicate that for FeCrAl cladding the input parameters with greatest influence on the output metrics of interest (fuel centerline temperature and cladding hoop strain) during the LOCA were the isotropic swellingmore » and fuel enrichment. For U3Si2 the important inputs were found to be the intergranular diffusion coefficient, specific heat, and fuel thermal conductivity. For the SBO scenario, Young’s modulus was found to be influential in FeCrAl in addition to the isotropic swelling and fuel enrichment. Contrarily to the LOCA case, the specific heat of U3Si2 was found to have no effect during the SBO. The intergranular diffusion coefficient and fuel thermal conductivity were still found to be of importance. The results of the sensitivity analyses have identified areas where further research is required including fission gas behavior in U3Si2 and irradiation swelling in FeCrAl. Moreover, the results highlight the need to perform the sensitivity analyses on full length fuel rods for SBO scenarios.« less

Magnetotransport and Heat Capacity in Ternary Compounds U3M2M‧3‧, M=Al, Ga; M=Si, Ge

NASA Astrophysics Data System (ADS)

Troć, R.; Rogl, P.; Tran, V. H.; Czopnik, A.

2001-05-01

We report detailed studies of magnetization, electrical resistivity, magnetoresistivity, and heat capacity performed on the novel family of intermetallic compounds U3M2M‧3, (M=Al, Ga, and M‧=Si, Ge). The present measurements support the earlier conclusions about the ferrimagnetic properties of silicides and ferromagnetic properties of germanides. The resistivity for both compounds U3{Al,Ga}2Si3 exhibits below TC a pronounced maximum observed for the first time in an actinoid-ferrimagnet, probably caused by (a) the reduction of the number of effective conduction carriers or (b) a SDW-type of spin-disorder scattering of electrons. Both low-temperature resistivity (except for U3Ga2Si3) and heat capacity may be described by a T-dependence involving a small gap Δ on the order of 30-50 K in the magnon dispersion. The Cp/T values at 2 K are enhanced and point to a medium-heavy fermion character of all these ternaries. Magnetoresistance for ferrimagnetic U3{Al,Ga}2Si3 is rather small but positive in correspondence of antiferromagnetic interactions. In correspondence to the ferromagnetic materials, negative magnetoresistance is encountered for U3{Al,Ga}2Ge3. Specific features in the temperature dependence of magnetoresistivity Δρ/ρ at various fields confirm the sinusoidal modulation of the magnetic structure for U3Al2Ge3 between 40 and 60 K. Also, such data for U3Ga2Ge3 present strong indications for a similar magnetic modulation between 63 and 93 K, yet to be discovered by neutron diffraction experiments. In addition, the transition at 63 K is furthermore well resolved in the specific heat data of U3Ga2Ge3.

The Ecology of Al-Samaliah Island, U.A.E.

NASA Astrophysics Data System (ADS)

Zahran, M. A.; Al-Ansari, F. M.

1999-08-01

Al-Samaliah Island is one of the inshore islands of U.A.E. located at about 12 km north-east of Abu Dhabi in the Arabian Gulf. It has a flat undulating surface with neither sand dunes nor rocky hills. Its sandy soil is generally salt-affected with variable percentages of salts. The vegetation of Al-Samaliah Island is essentially halophytic and may be categorized as: seagrasses, mangal and littoral saltmarsh types. The main species include: Cymodocea ciliata, Halophila spp. and Halodula univervis (seagrasses), some algae, Avicennia marina (mangrove), Arthrocnemum macrostachyum, Seidlitzia rosmarinus, and Suaeda vermiculata (salt marsh). Other halophytes commonly present are: Anabasis setifera, Halocnemum strobilaeum, Halopeplis perfoliata, Salsola imbricata and Zygophyllum gatarense in addition to two annuals: Schangenia aegyptiaca and Zygophyllum simplex. Phoenix dactylifera is cultivated in local areas covered with sandy sheets. Between the date palm trees there is a thin growth of Cyperus conglomeratus. Some plant species have been analysed chemically to determine their main constituents. The relationships between the environmental factors and the plant life of the islands are discussed.

The Effect of Si and Al Concentration Ratios on the Removal of U(VI) under Hanford Site 200 Area Conditions-12115

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katsenovich, Yelena; Gonzalez, Nathan; Moreno-Pastor, Carol

2012-07-01

Injection of reactive gases, such as NH{sub 3}, is an innovative technique to mitigate uranium contamination in soil for a vadose zone (VZ) contaminated with radionuclides. A series of experiments were conducted to examine the effect of the concentration ratio of silicon to aluminum in the presence of various bicarbonate concentrations on the coprecipitation process of U(VI). The concentration of Al in all tests remained unchanged at 2.8 mM. Experiments showed that the removal efficiency of uranium was not significantly affected by the different bicarbonate and U(VI) concentrations tested. For the lower Si:Al molar ratios of 2:1 and 18:1, themore » removal efficiency of uranium was relatively low (≤ 8%). For the Si:Al molar ratio of 35:1, the removal efficiency of uranium was increased to an average of ∼82% for all bicarbonate concentrations tested. At higher Si:Al molar ratios (53:1 and above), a relatively high removal efficiency of U(VI), approximately 85% and higher, was observed. These results demonstrate that the U(VI) removal efficiency is more affected by the Si:Al molar ratio than by the bicarbonate concentration in solution. The results of this experiment are promising for the potential implementation of NH{sub 3} gas injection for the remediation of U(VI) -contaminated VZ. (authors)« less

Seguridad Laboral al Usar Pesticidas

EPA Pesticide Factsheets

Para proteger a la gente que trabaja con pesticidas y quienes laboran en áreas tratadas con pesticidas; para educar al personal médico y al público acerca de cómo reconocer y tratar las enfermedades relacionadas a los pesticidas.

Band gap depiction of quaternary FeMnTiAl alloy using Hubbard (U) potential

NASA Astrophysics Data System (ADS)

Bhat, Tahir Mohiuddin; Yousuf, Saleem; Khandy, Shakeel Ahmad; Gupta, Dinesh C.

2018-05-01

We have employed self-consistent ab-initio calculations to investigate new quaternary alloy FeMnTiAl by applying Hubbard potential (U). The alloy is found to be stable in ferromagnetic phase with cubic structure. The alloy shows half-metallic (HM) ferromagnet character. The values of minority band gap FeMnTiAl are found to be 0.33 eV respectively. Electronic charge density reveals that both types of bonds covalent as well as ionic are present in the alloy. Thus the new quaternary alloy can be proved as vital contender for spin valves and spin generator devices.

Realization of the axial next-nearest-neighbor Ising model in U 3 Al 2 Ge 3

DOE PAGES

Fobes, David M.; Lin, Shi-Zeng; Ghimire, Nirmal J.; ...

2017-11-09

Inmore » this paper, we report small-angle neutron scattering (SANS) measurements and theoretical modeling of U 3 Al 2 Ge 3 . Analysis of the SANS data reveals a phase transition to sinusoidally modulated magnetic order at T N = 63 K to be second order and a first-order phase transition to ferromagnetic order at T c = 48 K. Within the sinusoidally modulated magnetic phase (T c < T < T N), we uncover a dramatic change, by a factor of 3, in the ordering wave vector as a function of temperature. Finally, these observations all indicate that U 3 Al 2 Ge 3 is a close realization of the three-dimensional axial next-nearest-neighbor Ising model, a prototypical framework for describing commensurate to incommensurate phase transitions in frustrated magnets.« less

Realization of the axial next-nearest-neighbor Ising model in U 3 Al 2 Ge 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fobes, David M.; Lin, Shi-Zeng; Ghimire, Nirmal J.

Inmore » this paper, we report small-angle neutron scattering (SANS) measurements and theoretical modeling of U 3 Al 2 Ge 3 . Analysis of the SANS data reveals a phase transition to sinusoidally modulated magnetic order at T N = 63 K to be second order and a first-order phase transition to ferromagnetic order at T c = 48 K. Within the sinusoidally modulated magnetic phase (T c < T < T N), we uncover a dramatic change, by a factor of 3, in the ordering wave vector as a function of temperature. Finally, these observations all indicate that U 3 Al 2 Ge 3 is a close realization of the three-dimensional axial next-nearest-neighbor Ising model, a prototypical framework for describing commensurate to incommensurate phase transitions in frustrated magnets.« less

A modelling study of the inter-diffusion layer formation in U-Mo/Al dispersion fuel plates at high power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, B.; Hofman, G. L.; Leenaers, A.

Post irradiation examinations of full-size U-Mo/Al dispersion fuel plates fabricated with ZrN- or Sicoated U-Mo particles revealed that the reaction rate of irradiation-induced U-Mo-Al inter-diffusion, an important microstructural change impacting the performance of this type of fuel, is temperature and fission-rate dependent. In order to simulate the U-Mo/Al inter-diffusion layer (IL) growth behavior in full-size dispersion fuel plates, the existing IL growth correlation was modified with a temperaturedependent multiplication factor that transits around a threshold fission rate. In-pile irradiation data from four tests in the BR2 reactors, including FUTURE, E-FUTURE, SELEMIUM, and SELEMIUM-1a, were utilized to determine and validate themore » updated IL growth correlation. Irradiation behavior of the plates was simulated with the DART-2D computational code. The general agreement between the calculated and measured fuel meat swelling and constituent volume fractions as a function of fission density demonstrated the plausibility of the updated IL growth correlation. The simulation results also suggested the temperature dependence of the IL growth rate, similar to the temperature dependence of the intermixing rate in ion-irradiated bi-layer systems.« less

Microstructural characterization of a thin film ZrN diffusion barrier in an As-fabricated U-7Mo/Al matrix dispersion fuel plate

NASA Astrophysics Data System (ADS)

Keiser, Dennis D.; Perez, Emmanuel; Wiencek, Tom; Leenaers, Ann; Van den Berghe, Sven

2015-03-01

The United States High Performance Research Reactor Fuel Development program is developing low enriched uranium fuels for application in research and test reactors. One concept utilizes U-7 wt.% Mo (U-7Mo) fuel particles dispersed in Al matrix, where the fuel particles are coated with a 1 μm-thick ZrN coating. The ZrN serves as a diffusion barrier to eliminate a deleterious reaction that can occur between U-7Mo and Al when a dispersion fuel is irradiated under aggressive reactor conditions. To investigate the final microstructure of a physically-vapor-deposited ZrN coating in a dispersion fuel plate after it was fabricated using a rolling process, characterization samples were taken from a fuel plate that was fabricated at 500 °C using ZrN-coated U-7Mo particles, Al matrix and AA6061 cladding. Scanning electron and transmission electron microscopy analysis were performed. Data from these analyses will be used to support future microstructural examinations of irradiated fuel plates, in terms of understanding the effects of irradiation on the ZrN microstructure, and to determine the role of diffusion barrier microstructure in eliminating fuel/matrix interactions during irradiation. The as-fabricated coating was determined to be cubic-ZrN (cF8) phase. It exhibited a columnar microstructure comprised of nanometer-sized grains and a region of relatively high porosity, mainly near the Al matrix. Small impurity-containing phases were observed at the U-7Mo/ZrN interface, and no interaction zone was observed at the ZrN/Al interface. The bonding between the U-7Mo and ZrN appeared to be mechanical in nature. A relatively high level of oxygen was observed in the ZrN coating, extending from the Al matrix in the ZrN coating in decreasing concentration. The above microstructural characteristics are discussed in terms of what may be most optimal for a diffusion barrier in a dispersion fuel plate application.

Antimycobacterial, antimicrobial, and biocompatibility properties of para-aminosalicylic acid with zinc layered hydroxide and Zn/Al layered double hydroxide nanocomposites

PubMed Central

Saifullah, Bullo; El Zowalaty, Mohamed E; Arulselvan, Palanisamy; Fakurazi, Sharida; Webster, Thomas J; Geilich, Benjamin M; Hussein, Mohd Zobir

2014-01-01

The treatment of tuberculosis by chemotherapy is complicated due to multiple drug prescriptions, long treatment duration, and adverse side effects. We report here for the first time an in vitro therapeutic effect of nanocomposites based on para-aminosalicylic acid with zinc layered hydroxide (PAS-ZLH) and zinc-aluminum layered double hydroxides (PAS-Zn/Al LDH), against mycobacteria, Gram-positive bacteria, and Gram-negative bacteria. The nanocomposites demonstrated good antimycobacterial activity and were found to be effective in killing Gram-positive and Gram-negative bacteria. A biocompatibility study revealed good biocompatibility of the PAS-ZLH nanocomposites against normal human MRC-5 lung cells. The para-aminosalicylic acid loading was quantified with high-performance liquid chromatography analysis. In summary, the present preliminary in vitro studies are highly encouraging for further in vivo studies of PAS-ZLH and PAS-Zn/Al LDH nanocomposites to treat tuberculosis. PMID:25114509

HEU Holdup Measurements in 321-M B and Spare U-Al Casting Furnaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salaymeh, S.R.

The Analytical Development Section of Savannah River Technology Center (SRTC) was requested by the Facilities Decontamination Division (FDD) to determine the holdup of enriched uranium in the 321-M facility as part of an overall deactivation project of the facility. The 321-M facility was used to fabricate enriched uranium fuel assemblies, lithium-aluminum target tubes, neptunium assemblies, and miscellaneous components for the production reactors. This report covers holdup measurements in two uranium aluminum alloy (U-Al) casting furnaces. Our results indicate an upper limit of 235U content for the B and Spare furnaces of 51 and 67 g respectively. This report discusses themore » methodology, non-destructive assay (NDA) measurements, and results of the uranium holdup on the two furnaces.« less

Al Qaeda and Affiliates: Historical Perspective, Global Presence, and Implications for U.S. Policy

DTIC Science & Technology

2010-02-05

mountainous tribal belt of northwest Pakistan, where it continues to train operatives, recruit, and disseminate propaganda. But Al Qaeda franchises or...April 2005 to U.S. charges of involvement in the September 11 plot, apparently visited Malaysia and met with cell members in 2000. Additionally, the...Qaeda leader, Malaysia was viewed as an ideal location for transiting and meeting because it allowed visa-free entry to citizens of most Gulf states

The effect of Si and Al concentrations on the removal of U(VI) in the alkaline conditions created by NH3 gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katsenovich, Yelena P.; Cardona, Claudia; Lapierre, Robert

2016-10-01

Remediation of uranium in the deep unsaturated zone is a challenging task, especially in the presence of oxygenated, high-carbonate alkalinity soil and pore water composition typical for arid and semi-arid environments of the western regions of the U.S. This study evaluates the effect of various pore water constituencies on changes of uranium concentrations in alkaline conditions, created in the presence of reactive gases such as NH3 to effectively mitigate uranium contamination in the vadose zone sediments. This contaminant is a potential source for groundwater pollution through slow infiltration of soluble and highly mobile uranium species towards the water table. Themore » objective of this research was to evaluate uranium sequestration efficiencies in the alkaline synthetic pore water solutions prepared in a broad range of Si, Al, and bicarbonate concentrations typically present in field systems of the western U.S. regions and identify solid uranium-bearing phases that result from ammonia gas treatment. In previous studies (Szecsody et al. 2012; Zhong et al. 2015), although uranium mobility was greatly decreased, solid phases could not be identified at the low uranium concentrations in field-contaminated sediments. The chemical composition of the synthetic pore water used in the experiments varied for silica (5–250 mM), Al3+ (2.8 or 5 mM), HCO3- (0–100 mM) and U(VI) (0.0021–0.0084 mM) in the solution mixture. Experiment results suggested that solutions with Si concentrations higher than 50 mM exhibited greater removal efficiencies of U(VI). Solutions with higher concentrations of bicarbonate also exhibited greater removal efficiencies for Si, Al, and U(VI). Overall, the silica polymerization reaction leading to the formation of Si gel correlated with the removal of U(VI), Si, and Al from the solution. If no Si polymerization was observed, there was no U removal from the supernatant solution. Speciation modeling indicated that the dominant uranium

The Al-Jazeera News Network: Opportunity or Challenge for U.S. Foreign Policy in the Middle East

DTIC Science & Technology

2003-07-23

vehemently. During the war in Afghanistan in 2001, Al- Jazeera’s Kabul office was accidently struck by U.S. fire. Despite Ayoub’s death , a recent article...series entitled “ Horseman Without a Horse.” The story was a chronicle of the Arab struggle against colonial rule and against the establishment of the

Tiempo para un cambio

NASA Astrophysics Data System (ADS)

Woltjer, L.

1987-06-01

En la reunion celebrada en diciembre dei ano pasado informe al Consejo de mi deseo de terminar mi contrato como Director General de la ESO una vez que fuera aprobado el proyecto dei VLT, que se espera sucedera hacia fines de este aAo. Cuando fue renovada mi designacion hace tres aAos, el Consejo conocia mi intencion de no completar los cinco aAos dei contrato debido a mi deseo de disponer de mas tiempo para otras actividades. Ahora, una vez terminada la fase preparatoria para el VLT, Y habiendose presentado el proyecto formalmente al Consejo el dia 31 de marzo, y esperando su muy probable aprobacion antes dei termino de este ano, me parece que el 10 de enero de 1988 presenta una excelente fecha para que se produzca un cambio en la administracion de la ESO.

A modelling study of the inter-diffusion layer formation in U-Mo/Al dispersion fuel plates at high power

NASA Astrophysics Data System (ADS)

Ye, B.; Hofman, G. L.; Leenaers, A.; Bergeron, A.; Kuzminov, V.; Van den Berghe, S.; Kim, Y. S.; Wallin, H.

2018-02-01

Post irradiation examinations of full-size U-Mo/Al dispersion fuel plates fabricated with ZrN- or Si- coated U-Mo particles revealed that the reaction rate of irradiation-induced U-Mo-Al inter-diffusion, an important microstructural change impacting the performance of this type of fuel, transited at a threshold temperature/fission rate. The existing inter-diffusion layer (IL) growth correlation, which does not describe the transition behavior of IL growth, was modified by applying a temperature-dependent multiplication factor that transits around a threshold fission rate. In-pile irradiation data from four tests in the BR2 reactors, including FUTURE, E-FUTURE, SELEMIUM, and SELEMIUM-1a, were utilized to determine and validate the updated IL growth correlation. Irradiation behavior of the plates was simulated with the DART-2D computational code. The general agreement between the calculated and measured fuel meat swelling and constituent volume fractions as a function of fission density demonstrated the plausibility of the updated IL growth correlation. The simulation results also suggested the temperature dependence of the IL growth rate, similar to the temperature dependence of the inter-mixing rate in ion-irradiated bi-layer systems.

U-based metallic glasses with superior glass forming ability

NASA Astrophysics Data System (ADS)

Xu, Hongyang; Ke, Haibo; Huang, Huogen; Zhang, Pengguo; Pu, Zhen; Zhang, Pei; Liu, Tianwei

2018-02-01

By using Al as the third and B as the fourth but minor alloying elements for the U66.7Co33.3 basic metallic glass, a series of U-Co-Al(-B) alloys were designed. The quaternary U-Co-Al-B alloys exhibit significantly improved glass-forming ability (GFA) than previously reported U-based metallic glasses. Low fragility (∼24) is found for these new U-based metallic glasses. The improvement in GFA would result from denser atomic packing in the undercooled liquids due to the presence of small B atoms. Some U-Co-Al(-B) glasses showed corrosion resistance comparable to that of U64Co34Al2 glass, known for premium anti-corrosive performance among the unveiled U-based glasses.

Estrategia de Aprendizaje Basado en Problemas (ABP) para explorar las concepciones alternativas relacionadas al tema estados de agregacion de la materia en estudiantes de nivel elemental =

NASA Astrophysics Data System (ADS)

Rosado Olivieri, Wilda Y.

Gran parte de la investigacion acerca de la ensenanza de las ciencias se dedica a estudiar la forma o manera en que los estudiantes visualizan los conceptos cientificos. Para Driver (1983) esas ideas o concepciones se conocen como concepciones alternativas; las cuales pueden ocasionar dificultad para comprender los conceptos de las diferentes areas del conocimiento. El proposito de este estudio fue: (a) indagar como las distintas etapas del ABP permiten explorar las concepciones alternativas que poseen los estudiantes de nivel elemental acerca de los estados de agregacion de la materia y, (b) explorar en que medida el ABP permite identificar e incorporar las concepciones alternativas que poseen los estudiantes de nivel elemental con relacion al concepto de estados de agregacion de la materia para facilitar su aprendizaje. Con el fin de explorar las concepciones alternativas en el tema de los estados agregados de la materia se implanto la estrategia de Aprendizaje Basado en Problemas (ABP) con estudiantes de quinto grado de nivel elemental. Se utilizo la metodologia mixta con varias estrategias de recopilacion de datos, como una pre y pos prueba para elucidar el conocimiento previo y al mismo tiempo las concepciones alternativas sobre el tema bajo estudio y luego verificar el aprendizaje en los estudiantes. Asimismo, el uso de mapas conceptuales para determinar la profundidad del tema estudiado y el entrelazamiento de los conceptos Una tercera estrategia fue el grupo focal para tomar en cuenta la impresion de los estudiantes acerca del proyecto ABP. El aspecto colaborativo y cooperativo fue un factor fundamental, ya que el aprendizaje ocurrio en ese contexto educativo. Para los hallazgos de esta investigacion fue tan importante el conocimiento previo como los procesos que se generaban para que la adquisicion del mismo fuera de forma significativa y funcional (Escribano & Del Valle, 2010). La estrategia de ABP constituyo en este estudio una forma para indagar las

The Effect of Early Diagenesis on the 238U/235U Ratio of Platform Carbonates.

NASA Astrophysics Data System (ADS)

Tissot, F.; Chen, C.; Go, B. M.; Naziemiec, M.; Healy, G.; Swart, P. K.; Dauphas, N.

2017-12-01

of all ages. We find that early diagenesis results in a 0 to +0.50 ‰ offset between the δ238U of carbonates and that of seawater. [1] Teng et al (2017) RiMG 82. [2] Tissot & Dauphas (2015) GCA 167. [3] Andersen et al. (2016) Chem. Geol. 420. [4] Ku et al (1977) Deep-Sea Research 24. [5] Dunk et al (2002) Chem. Geol. 190. [6] Romaniello et al (2013) Chem. Geol. 362. [7] Andersen et al. (2014) EPSL 400.

PRELIMINARY EVALUATION OF FeCrAl CLADDING AND U-Si FUEL FOR ACCIDENT TOLERANT FUEL CONCEPTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hales, J. D.; Gamble, K. A.

2015-09-01

Since the accident at the Fukushima Daiichi Nuclear Power Station, enhancing the accident tolerance of light water reactors (LWRs) has become an important research topic. In particular, the community is actively developing enhanced fuels and cladding for LWRs to improve safety in the event of accidents in the reactor or spent fuel pools. Fuels with enhanced accident tolerance are those that, in comparison with the standard UO2-zirconium alloy system, can tolerate loss of active cooling in the reactor core for a considerably longer time period during design-basis and beyond design-basis events while maintaining or improving the fuel performance during normalmore » operations and operational transients. This paper presents early work in developing thermal and mechanical models for two materials that may have promise: U-Si for fuel, and FeCrAl for cladding. These materials would not necessarily be used together in the same fuel system, but individually have promising characteristics. BISON, the finite element-based fuel performance code in development at Idaho National Laboratory, was used to compare results from normal operation conditions with Zr-4/UO2 behavior. In addition, sensitivity studies are presented for evaluating the relative importance of material parameters such as ductility and thermal conductivity in FeCrAl and U-Si in order to provide guidance on future experiments for these materials.« less

The Application of 238U/235U as a Redox-Proxy for Past Ocean Chemistry

NASA Astrophysics Data System (ADS)

Andersen, M. B.; Westermann, S.; Bahniuk, A.; Vasconcelos, C.; McKenzie, J. A.; Föllmi, K. B.; Vance, D.

2014-12-01

The recent discovery of significant variation in 238U/235U caused by redox change at the surface Earth has led to its use to extract information on the oxygenation state of ancient oceans from marine sediments [e.g. 1]. Recent studies have focused on improving the understanding of the 238U/235U signature in modern marine carbonates [2] and black shales [3] to improve the robustness of this tracer. To further advance its use we have focused on improving our understanding of 238U/235U systematics in modern dolomite, another commonly occurring rock-type in the geological record, before turning to 238U/235U signatures in ancient sediments. The measured dolomite samples, precipitated in modern environments of coastal hypersaline lagoons in Brazil, all exhibit 238U/235U values that deviate from the seawater composition [3]. Observed values are both lighter (ca. 130 ppm; as also observed in dolomite from tidal-ponds on Bahamas [2]) and heavier (50-180 ppm). These distinct 238U/235U values for different dolomite-precipitates likely attest to the particular formation style, as well as early diagenetic processes. We use such modern settings to discuss the utility of 238U/235U in ancient sediments, the singularity of any observed 238U/235U signal, its relation to global ocean chemistry and potential diagenetic overprinting. These constraints are then used to evaluate a well-preserved marine carbonate section [4] and published black shale 238U/235U data [1], both deposited during the Oceanic Anoxic Event 2 (93 Ma). We discuss the capabilities of both the carbonate and black shale section for retaining information on the 238U/235U composition in the ocean during OAE 2. [1] Montoya-Pino et al. (2010) Geology, 38, 315-318 [2] Romaniello et al. (2013) 362, 305-316 [3] Andersen et al. (2014) EPSL, 400, 184-194 [4] Westermann et al. (2010) Cret. Res., 31, 500-514

SEM in situ MiniCantilever Beam Bending of U-10Mo/Zr/Al Fuel Elements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mook, William; Baldwin, Jon K.; Martinez, Ricardo M.

2014-06-16

In this work, the fracture behavior of Al/Zr and Zr/dU-10Mo interfaces was measured via the minicantilever bend technique. The energy dissipation rates were found to be approximately 3.7-5 mj/mm 2 and 5.9 mj/mm 2 for each interface, respectively. It was found that in order to test the Zr/U-10Mo interface, location of the hinge of the cantilever was a key parameter. While this test could be adapted to hot cell use through careful alignment fixturing and measurement of crack lengths with an optical microscope (as opposed to SEM, which was used here out of convenience), machining of the cantilevers via MiniMillmore » in such a way as to locate the interfaces at the cantilever hinge, as well as proper placement of a femtosecond laser notch will continue to be key challenges in a hot cell environment.« less

Accurate ab initio calculations which demonstrate a 3 Pi u ground state for Al2

NASA Technical Reports Server (NTRS)

Bauschlicher, Charles W., Jr.; Partridge, Harry; Langhoff, Stephen R.; Taylor, Peter R.; Walch, Stephen P.

1986-01-01

The spectroscopic parameters and separations between the three low-lying X 3 Pi u, A 3 Sigma g -, and a 1 Sigma g + states of Al2 are studied as a function of both the one-particle and n-particle basis set. Approximate correlation treatments are calibrated against full Cl calculations correlating the six valence electrons in a double-zeta plus two d-function basis set. Since the CASSCF/MRCI 3 Pi u to 3 Sigma g - separation is in excellent agreement wtih the FCI value, the MRCI calculations were carried out in an extended (20s13p6d4f)/(6s5p3d2f) gaussian basis. Including a small correction for relativistic effects, the best estimate is that 3 Sigma g - state lies 174/cm above the 3 Pi u ground state. The 1 Sigma g + state lies at least 2000/cm higher in energy. At the CPF level, inclusion of 2s and 2p correlation has little effect on D sub e, reduces T sub e by only 26/cm, and shortens the bond lengths by about 0.02 a sub o. Further strong support for a 3 Pi u ground state comes from the experimental absorption spectra, since both observed transitions can be convincingly assigned as 3 Pi u yields 3 Pi g. The (2) 3 Pi g state is observed to be sensitive to the level of correlation treatment, and to have its minimum shifted to shorter rho values, such that the strongest experimental absorption peak probably corresponds to the 0 yields 2 transition.

Interaction Between U-Mo Alloys and Alloys Al-Be

NASA Astrophysics Data System (ADS)

Nikitin, S. N.; Tarasov, B. A.; Shornikov, D. P.

The main objective of the work is the experimental determination of the effect of doping on the kinetics of the interaction of beryllium, aluminum and uranium-molybdenum alloy dispersed in the nuclear fuel. It is shown that an increase in the content of Be in Al leads to a linear decrease in the rate of interaction of the alloy with uranium-molybdenum alloy. Besides AlBe-alloys have higher thermal and mechanical properties than other matrix alloys such as AlSi.

238U/235U determinations of some commonly used reference materials and U-bearing accessory minerals (Invited)

NASA Astrophysics Data System (ADS)

Condon, D.; Noble, S.; McLean, N.; Bowring, S. A.

2009-12-01

We have determined 238U/235U ratios for a suite of commonly used natural (CRM 112a, SRM 950a, HU-1) and synthetic (IRMM 184 and CRM U500) uranium reference materials in addition to several U-bearing accessory phases (zircon and monazite) by thermal ionisation mass-spectrometry (TIMS) using the IRMM 3636 233U-236U double spike to accurately correct for mass fractionation. The 238U/235U values for the natural uranium reference materials differ, by up to 0.1%, from the widely used ‘consensus’ value (137.88) with all having 238U/235U values less than 137.88. Similarly, initial 238U/235U data from zircon and monazite yield 238U/235U values that are lower than the ‘consensus’ value. The data obtained from U-bearing minerals is used to assess how the uncertainty in the 238U/235U ratio contributes to the systematic discordance observed in 238U/206Pb and 235U/207Pb dates (Mattinson, 2000; Schoene et al., 2006) which has traditionally been wholly attributed to error in the U decay constants. The 238U/235U determinations made on the synthetic reference materials yield results that are considerably more precise and accurate than the certified values (0.02% vs. 0.1% for CRM U500). The calibration of isotopic tracers used for U-daughter geochronology that are partially based upon these reference materials, and the resultant age determinations, will benefit from increased accuracy and precision. Mattinson, J.M., 2000. Revising the “gold standard”—the uranium decay constants of Jaffey et al., 1971. Eos Trans. AGU, Spring Meet. Suppl., Abstract V61A-02. Schoene B., Crowley J.L., Condon D.C., Schmitz M.D., Bowring S.A., 2006, Reassessing the uranium decay constants for geochronology using ID-TIMS U-Pb data. Geochimica et Cosmochimica Acta 70: 426-445

Phase stability and electronic structure of UMo2Al20: A first-principles study

NASA Astrophysics Data System (ADS)

Liu, Peng-Chuang; Xian, Ya-Jiang; Wang, Xin; Zhang, Yu-Ting; Zhang, Peng-Cheng

2017-09-01

In this paper, the phase stability of UMo2Al20 was explored using cluster formula in combination with first-principles calculations. Cluster formula analysis uncovered that the compound was composed of two principal clusters, i.e. [Mo-Al12] and [U-Al16]. The electronic interactions between U, Mo and Al atoms in this compound were discussed using elastic property, Bader charges and energy-resolved local bonding analysis, as well as the electronic interactions between Mo and Al atoms in [Mo-Al12] cluster and between U and Al atoms in [U-Al16] cluster. It revealed that UMo2Al20 satisfied the mechanical stability criterion for cubic system, and exhibited near ionic bonding character with weak bonding directionality. The calculations within both standard DFT and HSE frameworks demonstrated that U and Al atoms acted as an electron donor while Mo atoms acted as electron acceptor. The intrinsic stability of UMo2Al20 mainly stemmed from the bonding states of Mo-Al bonds and Al-Al bonds in [Mo-Al12] cluster. These calculations provide a further insight on the CeCr2Al20-type ternary compounds.

The effect of d and f states of ytterbium on the electronic and magnetic properties of Al1‑xYbxN: DFT+U study

NASA Astrophysics Data System (ADS)

Belhachi, S.

2018-04-01

Using density functional theory combined LSDA+U method, the structural, electronic and magnetic behaviors of ytterbium implanted in wurtzite AlN were investigated. Low formation energy shows that Yb atom favors to substitute for Al site and to confirm this stability, the adsorption energy has been calculated. It is found that Al0.9375Yb0.0625N possesses a semiconductor behavior. The magnetic moment 0.9891 μB per molecule principally comes from Yb ion with small contribution from the Al and N atoms. We predict that Yb ions order ferromagnetically in AlN. The hybridization between the f orbital of the Yb atom and the p orbital of the N atom is also observed. We see that AlN:Yb will be among the good candidates for spintronic applications.

Para-hydrogen perspectives in hyperpolarized NMR.

PubMed

Glöggler, Stefan; Colell, Johannes; Appelt, Stephan

2013-10-01

The first instance of para-hydrogen induced polarization (PHIP) in an NMR experiment was serendipitously observed in the 1980s while investigating a hydrogenation reaction (Seldler et al., 1983; Bowers and Weitekamp, 1986, 1987; Eisenschmid et al., 1987) [1-4]. Remarkably a theoretical investigation of the applicability of para-hydrogen as a hyperpolarization agent was being performed in the 1980's thereby quickly providing a theoretical basis for the PHIP-effect (Bowers and Weitekamp, 1986) [2]. The discovery of signal amplification by a non-hydrogenating interaction with para-hydrogen has recently extended the interest to exploit the PHIP effect, as it enables investigation of compounds without structural alteration while retaining the advantages of spectroscopy with hyperpolarized compounds [5]. In this article we will place more emphasis of the future applications of the method while only briefly discussing the efforts that have been made in the understanding of the phenomenon and the development of the method so far. Copyright © 2013 Elsevier Inc. All rights reserved.

The lowest ionization potentials of Al2

NASA Technical Reports Server (NTRS)

Bauschlicher, Charles W., Jr.; Barnes, Leslie A.; Taylor, Peter R.

1988-01-01

Potential curves for the lowest two electronic states (X 2 sigma g + and A 2 pi u) of Al2(+) were computed using complete active space SCF/multireference CI wave functions and large Gaussian basis sets. The lowest observable vertical ionization potential (to Al2(+) X 2 sigma g +) of the Al2 X 3 pi u ground state is calculated to occur around 6.1 eV, in excellent agreement with the experimental range of 6.0 to 6.42 eV obtained in recent cluster ionization studies by Cox and co-workers. The second vertical ionization potential (to Al2(+) A 2 pi u) occurs near 6.4 eV, also within the experimental range. The adiabatic IP of 5.90 eV is in good agreement with the value of 5.8 to 6.1 eV deduced by Hanley and co-workers from the difference in thresholds between collision induced dissociation processes of Al3(+). The computed IP values are somewhat larger than those deduced from branching ratios in cluster fragmentation experiments by Jarrold and co-workers. The observation of an ionization threshold below 6.42 eV is shown to be incompatible with an Al2 ground electronic state assignment of 3 sigma g -, but the separation between the two lowest states of Al2 is so small that it is likely that both are populated in the experiments, so that this does not provide unambiguous support for the recent theoretical assignment of the ground state as 3 pi u.

Al Qaeda in the Arabian Peninsula (AQAP): An Al Qaeda Affiliate Case Study

DTIC Science & Technology

2017-10-01

Underwear Bombing ” and an unsuccessful 2010 plan to put parcel bombs on U.S.-bound airplanes. AQAP also seeks to inspire “lone jihad” attacks in the... bomb -maker,5 and Sudanese national Ibrahim al-Qosi, a former bookkeeper for Osama Bin Laden.6 Below the emir are regional commanders and heads of...5 “Profile: Al-Qaeda ‘ Bomb Maker’ Ibrahim al-Asiri,” BBC News, July 4, 2014, http://www.bbc.com/news/world-middle-east-11662143. See also al-Asiri

Electron Transfer Pathways Facilitating U(VI) Reduction by Fe(II) on Al- vs Fe-Oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, S. D.; Becker, U.; Rosso, K. M.

This study continues mechanistic development of heterogeneous electron transfer (ET) pathways at mineral surfaces in aquatic environments that enable the reduction U(VI) by surface-associated Fe(II). Using computational molecular simulation within the framework of Marcus Theory, our findings highlight the importance of the configurations and interaction of the electron donor and acceptor species with the substrate, with respect to influencing its electronic structure and thereby the ability of semiconducting minerals to facilitate ET. U(VI) reduction by surface-associated Fe(II) (adsorbed or structurally incorporated into the lattice) on an insulating, corundum (001) surface (α-Al2O3) occurs when proximal inner-sphere (IS) surface complexes are formed,more » such that ET occurs through a combination of direct exchange (i.e., Fe d- and U f-orbitals overlap through space) and superexchange via intervening surface oxygen atoms. U(VI) reduction by coadsorbed Fe(II) on the isostructural semiconducting hematite (α-Fe2O3) basal surface requires either their direct electronic interaction (e.g., IS complexation) or mediation of this interaction indirectly through the surface via an intrasurface pathway. Conceptually possible longer-range ET by charge-hopping through surface Fe atoms was investigated to determine whether this indirect pathway is competitive with direct ET. The calculations show that energy barriers are large for this conduction-based pathway; interfacial ET into the hematite surface is endothermic (+80.1 kJ/mol) and comprises the rate-limiting step (10–6 s–1). The presence of the IS adsorbates appears to weaken the electronic coupling between underlying Fe ions within the surface, resulting in slower intra-surface ET (10–5 s–1) than expected in the bulk basal plane. Our findings lay out first insights into donor-acceptor communication via a charge-hopping pathway through the surface for heterogeneous reduction of U(VI) by Fe(II) and help provide

Fosetyl-al

Integrated Risk Information System (IRIS)

Integrated Risk Information System ( IRIS ) Chemical Assessment Summary U.S . Environmental Protection Agency National Center for Environmental Assessment This IRIS Summary has been removed from the IRIS database and is available for historical reference purposes . ( July 2016 ) Fosetyl - al ; CASRN

26Al- 26Mg and 207Pb- 206Pb systematics of Allende CAIs: Canonical solar initial 26Al/ 27Al ratio reinstated

NASA Astrophysics Data System (ADS)

Jacobsen, Benjamin; Yin, Qing-zhu; Moynier, Frederic; Amelin, Yuri; Krot, Alexander N.; Nagashima, Kazuhide; Hutcheon, Ian D.; Palme, Herbert

2008-07-01

The precise knowledge of the initial 26Al/ 27Al ratio [( 26Al/ 27Al) 0] is crucial if we are to use the very first solid objects formed in our Solar System, calcium-aluminum-rich inclusions (CAIs) as the "time zero" age-anchor and guide future work with other short-lived radio-chronometers in the early Solar System, as well as determining the inventory of heat budgets from radioactivities for early planetary differentiation. New high-precision multi-collector inductively-coupled plasma mass spectrometry (MC-ICP-MS) measurements of 27Al/ 24Mg ratios and Mg-isotopic compositions of nine whole-rock CAIs (six mineralogically characterized fragments and three micro-drilled inclusions) from the CV carbonaceous chondrite, Allende yield a well-defined 26Al- 26Mg fossil isochron with an ( 26Al/ 27Al) 0 of (5.23 ± 0.13) × 10 - 5 . Internal mineral isochrons obtained for three of these CAIs ( A44A, AJEF, and A43) are consistent with the whole-rock CAI isochron. The mineral isochron of AJEF with ( 26Al/ 27Al) 0 = (4.96 ± 0.25) × 10 - 5 , anchored to our precisely determined absolute 207Pb- 206Pb age of 4567.60 ± 0.36 Ma for the same mineral separates, reinstate the "canonical" ( 26Al/ 27Al) 0 of 5 × 10 - 5 for the early Solar System. The uncertainty in ( 26Al/ 27Al) 0 corresponds to a maximum time span of ± 20 Ka (thousand years), suggesting that the Allende CAI formation events were culminated within this time span. Although all Allende CAIs studied experienced multistage formation history, including melting and evaporation in the solar nebula and post-crystallization alteration likely on the asteroidal parent body, the 26Al- 26Mg and U-Pb-isotopic systematics of the mineral separates and bulk CAIs behaved largely as closed-system since their formation. Our data do not support the "supra-canonical" 26Al/ 27Al ratio of individual minerals or their mixtures in CV CAIs, suggesting that the supra-canonical 26Al/ 27Al ratio in the CV CAIs may have resulted from post

Overview of lower length scale model development for accident tolerant fuels regarding U3Si2 fuel and FeCrAl cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yongfeng

2016-09-01

U3Si2 and FeCrAl have been proposed as fuel and cladding concepts, respectively, for accident tolerance fuels with higher tolerance to accident scenarios compared to UO2. However, a lot of key physics and material properties regarding their in-pile performance are yet to be explored. To accelerate the understanding and reduce the cost of experimental studies, multiscale modeling and simulation are used to develop physics-based materials models to assist engineering scale fuel performance modeling. In this report, the lower-length-scale efforts in method and material model development supported by the Accident Tolerance Fuel (ATF) high-impact-problem (HIP) under the NEAMS program are summarized. Significantmore » progresses have been made regarding interatomic potential, phase field models for phase decomposition and gas bubble formation, and thermal conductivity for U3Si2 fuel, and precipitation in FeCrAl cladding. The accomplishments are very useful by providing atomistic and mesoscale tools, improving the current understanding, and delivering engineering scale models for these two ATF concepts.« less

High Resolution Dating of Louisville Guyots from IODP Sites U1372, U1375, U1376 and U1377: Implications for post-erosional hotspot ocean island processes and volcanism

NASA Astrophysics Data System (ADS)

Heaton, D. E.; Koppers, A. A. P.

2014-12-01

Here we will present new 40Ar/39Ar Ages results from the International Ocean Drilling Project (IODP) Sites U1372 (n=18), U1375 (n=3), U1376 (n=15) and U1377 (n=7) during Expedition 330 that drilled the northern end of the Louisville Seamount trail. The Louisville Seamount trail displays age progressive volcanism thought to be formed as the Pacific plate moved over a hotspot. The older seamounts are located in the north (80 Ma, Osbourn Guyot) and younger seamounts to the south. Seamounts in this study are all guyots from the older section of the seamount trail (~74 Ma, Site U1372 at Canopus Guyot to ~51 Ma, Site U1377 at Hadar Guyot). Sites U1372 and U1376 respectively recovered ~230 m and ~140 m of basaltic material beneath a thin sediment interface and contain many in-situ lava flows that are interlayed with volcaniclastics, breccias and intrusive sheets. 40Ar/39Ar measurements will be used to date these different lithologies and, along with paleomagnetic inclination data, determine whether there was post-erosional volcanism and postulate which processes are involved with either the construction or deconstruction of ocean islands. Koppers et al. (2012) noted that some holes had consistent paleomagnetic inclinations suggesting that at least the larger clasts in the volcaniclastic breccias were emplaced hot or otherwise had been reset post deposition. If this is the case and breccias were emplaced hot then this would explain the undetectable levels of CO2 remaining in glasses after a complete degassing of the lithologies (Nichols et al., 2014). This would further support evidence for shallow eruption depths and post-erosional volcanism. In addition, the 40Ar/39Ar ages should be able to resolve whether or not the breccias were emplaced during the same time period as underlying and overlying intrusive sheets. Samples were analyzed using a high-resolution incremental step-heating method at Oregon State University in the Geochronology Lab using a Thermo Scientific ARGUS

U.S. Navy Statutory Monitoring of Tributyltin in Selected U.S. Harbors

DTIC Science & Technology

1990-06-01

U.S. Navy and has very little commercial and private use. Tributyltin loading from Navy ships painted with TBT antifoulants was closely correlated (r 2...evaluated major tributyltin ( TBT ) sources ar well as tidal, vertical, and spatial variability (Valkirs et al., 1986; Seligman et al., 1986; Seligman et al... tributyltin antifouling paints to deter- mine both their efficacy and environmental concentration resulting from use of these TBT antifouling coatings

Al-Shebab: An Al-Qaeda Affiliate Case Study (2Rev)

DTIC Science & Technology

2017-10-01

explosives and car bombs . Al-Shebab’s joining Al-Qaeda had mutual benefits: AQ’s presence in East Africa dates to Osama Bin Laden’s time in Sudan...1992–1996) and the establishment of cells that perpetrated the August 7, 1998 bombings of the U.S. embassies in Nairobi, Kenya, and Dar es Salaam...to build an emirate in the Gedo region, but the project was crushed by Ethiopian forces after AIAI perpetrated several bombings in Ethiopia.25 The

The 238U/235U isotope ratio of the Earth and the solar system: Constrains from a gravimetrically calibrated U double spike and implications for absolute Pb-Pb ages

NASA Astrophysics Data System (ADS)

Weyer, Stefan; Noordmann, Janine; Brennecka, Greg; Richter, Stephan

2010-05-01

basalts to be the best representation of the U isotope composition of the Earth and the solar system, and the new 238U/235U for SRM 950a of 137.836, this would result in an average 238U/235U for the Earth and the solar system of ~ 137.80. The effect of a revised 238U/235U ratio on Pb-Pb ages is age dependent. It results in an age overestimation of ~0.8 Ma for the age of the solar system and up to 1.5 Ma for very young material (with bulk Earth U isotope composition). [1] Stirling, C.H., Andersen, M.B., Potter, E.-K., et al. (2007) EPSL 264, 208-225; [2] Weyer, S., Anbar, A. D., Gerdes, A., et al. (2008) GCA 72, 345-359. [3] Bopp, C.H., Lundstrom, C.C., Johnsons, T.M., Glessner, J.G. (2009) Geology 37, 611-614. [4] Brennecka, G.A., Weyer, S., Wadhwa, et al. (2010) Science, 327, p. 449. [5] Richter, S., Alonzo-Munoz, A., Eykens, R., et al. (2008) IJMS 269, 145-148. [6] Richter, S., et al. EGU meeting 2010.

Prospective study of cost of care at multidisciplinary ALS centers adhering to American Academy of Neurology (AAN) ALS practice parameters.

PubMed

Boylan, Kevin; Levine, Todd; Lomen-Hoerth, Catherine; Lyon, Mary; Maginnis, Kimberly; Callas, Peter; Gaspari, Celeste; Tandan, Rup

2015-01-01

Multidisciplinary care in ALS is associated with longer survival, improved quality of life, and reduced hospital admissions, but there are no published data on institutional costs associated with multidisciplinary ALS care at U.S. centers. We prospectively examined institutional costs, adherence to AAN Practice Parameters and patient satisfaction in multidisciplinary ALS clinics at 18 U.S. ALS centers. Centers reported patient volumes; direct costs for staff salary/benefits, supplies and equipment; and institutional non-salary and overhead costs over a three-month period. In 1117 patients seen during this period, mean age was 61.5 years (range 25-91 years), 56% were male, and mean ALSFRS-R score was 29. Mean total salary/benefit cost per clinic day for all providers was $2964 (range $1692-$5236 across centers). Mean salary/benefit cost per patient per clinic was $507 (range $258-$806 across centers). Differences among centers in reporting non-salary costs prevented meaningful analysis. Practice parameter adherence and patient satisfaction were high. This prospective collaborative study demonstrates the direct financial burden of evidence-based multidisciplinary ALS care in the U.S.; more refined non-salary and overhead cost data are needed to evaluate the full cost impact of care. These data may be useful in supporting evidence-based models of patient centered care for ALS.

Reporting from Qatar, this is Al-Jazeera

DTIC Science & Technology

2006-03-15

facts of the stories and draw conclusions to Al-Jazeera’s motives and the effects of its reporting on U.S. military operations in Iraq. REPORTING FROM...vignettes examine the facts of the stories and draw conclusions to Al-Jazeera’s motives and the effects of its reporting on U.S. military operations...after a period of five years and no longer reliant on state funds through the sale of program advertisement and exclusive video footage to other

Low-Al and high-Al trondhjemites in the Huai'an Complex, North China Craton: Geochemistry, zircon U-Pb and Hf isotopes, and implications for Neoarchean crustal growth and remelting

NASA Astrophysics Data System (ADS)

Zhang, Hua-Feng; Zhai, Ming-Guo; Santosh, M.; Li, Sheng-Rong

2012-04-01

Voluminous tonalite-trondhjemite-granodiorite (TTG) magmas were emplaced in the Huai'an Complex of North China Craton (NCC) during the Neoarchean. Here we present the geochemical characteristics of these rocks and identify low-Al (LAl) and high-Al (HAl) types of trondhjemites within the TTG suite. The LAl group displays high silica (SiO2 = 77-80 wt.%), and low Al2O3 contents (11.06-11.89 wt.%), a strongly peraluminous (A/CNK = 1.16 and 1.19) composition and enrichment in HREE (LaN/YbN = 4 and 5, GdN/YbN = 0.35 and 0.9). Their low Rb (13 and 28 ppm), Th (0.3 and 7.0 ppm), relatively high Na2O/K2O values (3.6 and 4.1) and MgO (0.63 and 0.68 wt.%) with moderately high Mg# (36 and 53), suggest crystallization from a primitive source. The HAl group is characterized by relatively low SiO2 (67.22-71.57 wt.%) and high Al2O3 contents (16.35-16.41 wt.%) with trace element contents and distribution patterns closely comparable to those of Archean high-Al TTGs. Our geochemical data do not favor a direct genetic link between the LAl and HAl trondhjemite groups. The zircon U-Pb data reveal that the LAl and HAl groups represent coeval intrusions at ca. 2.55-2.5 Ga. In situ analysis of Hf isotopes in the zircons (ɛHf = +5.6 to +10, and TDM = 2462-2595 Ma), together with the geochemical features of the low-Al trondhjemites suggest that they were generated under relatively low pressure (<8 kbar), through low degree partial melting of a newly accreted amphibolitic crust. Taking into consideration the contemporaneous (2.55-2.50 Ga) high-Al TTGs widely exposed in the Huai'an Complex, we suggest that the low-Al trondhjemites were formed by intraplating of mantle-derived magmas, and the coeval high-Al TTGs were produced by partial melting of a thickened lower crust, triggered by underplating. Our study attests to a major episode of Neoarchean crustal growth in the NCC, and remelting induced by underplating and intraplating of mantle-derived magmas.

Electronic structures of U X3 (X =Al , Ga, and In) studied by photoelectron spectroscopy

NASA Astrophysics Data System (ADS)

Fujimori, Shin-ichi; Kobata, Masaaki; Takeda, Yukiharu; Okane, Tetsuo; Saitoh, Yuji; Fujimori, Atsushi; Yamagami, Hiroshi; Haga, Yoshinori; Yamamoto, Etsuji; Ōnuki, Yoshichika

2017-09-01

The electronic structures of U X3 (X =Al , Ga , and In ) were studied by photoelectron spectroscopy to understand the relationship between their electronic structures and magnetic properties. The band structures and Fermi surfaces of UAl3 and UGa3 were revealed experimentally by angle-resolved photoelectron spectroscopy (ARPES), and they were compared with the result of band-structure calculations. The topologies of the Fermi surfaces and the band structures of UAl3 and UGa3 were explained reasonably well by the calculation, although bands near the Fermi level (EF) were renormalized owing to the finite electron correlation effect. The topologies of the Fermi surfaces of UAl3 and UGa3 are very similar to each other, except for some minor differences. Such minor differences in their Fermi surface or electron correlation effect might take an essential role in their different magnetic properties. No significant changes were observed between the ARPES spectra of UGa3 in the paramagnetic and antiferromagnetic phases, suggesting that UGa3 is an itinerant weak antiferromagnet. The effect of chemical pressure on the electronic structures of U X3 compounds was also studied by utilizing the smaller lattice constants of UAl3 and UGa3 than that of UIn3. The valence band spectrum of UIn3 is accompanied by a satellitelike structure on the high-binding-energy side. The core-level spectrum of UIn3 is also qualitatively different from those of UAl3 and UGa3. These findings suggest that the U 5 f states in UIn3 are more localized than those in UAl3 and UGa3.

Prospects for Practical Laser Ablation U/Pb and (U-Th)/He Double-Dating (LADD) of Detrital Apatite

NASA Astrophysics Data System (ADS)

Horne, A.; Hodges, K. V.; Van Soest, M. C.

2017-12-01

A laser ablation micro-analytical technique for (U-Th)/He dating has been shown to be an effective approach to the thermochronologic study of detrital zircons (Tripathy-Lang et al., J. Geophys. Res., 2013), while Evans et al. (J. Anal. At. Spectrom., 2015) and Horne et al. (Geochim. Cosmochim. Acta, 2016) demonstrated how the technique could be modified to enable laser ablation U/Pb and (U-Th)/He double-dating (LADD) of detrital zircon and titanite. These successes beg the question of whether or not LADD is viable for another commonly encountered detrital mineral: apatite. Exploratory LADD studies in Arizona State University's Group 18 Laboratories - using Durango fluorapatite, apatite from the Fish Canyon tuff, and detrital apatite from modern fluvial sediments in the eastern Sierra Nevada of California - illustrate that the method is indeed viable for detrital apatite. However, the method may not be appropriate for all detrital samples. For example, many apatite grains encountered in detrital samples from young orogenic settings have low concentrations of U and Th and small crystal sizes. This can lead to imprecise laser ablation (U-Th)/He dates, especially for very young grains potentially obscuring or inhibiting relevant interpretations of the data set.

Constraining the Uplift History of the Jabal Akhdar and Saih Hatat Culminations, Al Hajar Mountains, Oman, with Fission Track and (U-Th)/He Ages

NASA Astrophysics Data System (ADS)

Hansman, R. J.; Ring, U.; Thomson, S. N.; Den Brok, B.; Stübner, K.

2016-12-01

We constrain the timing of the enigmatic uplift history of the Al Hajar Mountains in Oman by apatite (U-Th)/He and fission-track (AHe and AFT), as well as zircon (U-Th)/He (ZHe) ages. Our data show differential cooling between the two major culminations of the mountain range, which are separated by the Semail gap, a major NNE-oriented depression in the Al Hajar Mountains. In the up to 3 km high Jabal Akhdar Culmination west of the Semail Gap AHe sample mean ages range between 35.5 ± 4.3 Ma and 23.9 ± 8.8 Ma (1σ errors), AFT ages range 51 ± 4 to 32 ± 2 Ma (1σ errors), and ZHe sample mean ages range 50.6 ± 16.7 to 46.1 ± 7.1 Ma (1σ errors). Whereas, in the Saih Hatat Culmination to the east AHe ages range from 23.6 ± 1.7 Ma to 15.7 ± 4.1 Ma, AFT ages range 73 ± 10 to 57 ± 4 Ma, and ZHe ages range 70.6 ± 10.8 Ma through to 58.8 ± 1.8 Ma. These data demonstrate that the uplift initiated at 45 Ma and had ceased by 15 Ma, climaxing between 40 to 35 Ma. In addition, U-Pb dating of calcite tectonics also supports N-S shortening at 40 to 35 Ma. We propose that the Semail gap is a west-dipping thrust, which uplifted the Jabal Akhdar Culmination in the hanging-wall but hardly affected the Saih Hatat Culmination in the footwall. During mountain uplift, the Al Hajar Mountains were located at least 600 km outboard of the current Eurasia-Arabia subduction/collision zone on the continental margin of the downgoing Arabian Plate. We therefore conclude that the uplift of the Al Hajar Mountains preceded the Zagros collisional event by at least 15 Myr and were not causally related to the Zagros collision and Makran subduction.

Imagens do céu ontem e hoje - um multimídia interativo de astronomia e uma nova exposição no MAST

NASA Astrophysics Data System (ADS)

Caretta, C. A.; Lima, F. P.; Requeijo, F.; Vieira, G. G.; Alves, F.; Valente, M. E. A.; de Almeida, R.; de Garcia, G. C.; Quixadá, A. C.

2003-08-01

"Imagens do Céu Ontem e Hoje" é o título de uma nova exposição que está sendo inaugurada no Museu de Astronomia e Ciências Afins (MCT), que inclui experimentos interativos, maquetes, réplicas e 8 terminais de computador com um multimídia interativo sobre Astronomia para consulta dos visitantes. O multimídia apresenta um conteúdo bastante extenso, que engloba quase todos os temas em Astronomia, consistindo numa fonte de divulgação e pesquisa para um público que vai das crianças até estudantes universitários. O conteúdo está distribuído em mais de 500 páginas de texto divididas em 4 módulos: "O Universo", "Espectroscopia", "Telescópios" e "Observando o Céu". Cada módulo é subdividido em 5 seções, em média, cada uma iniciada por uma animação que ilustra os temas a serem abordados na seção. Ao final da animação, uma lista de temas é apresentada sob o título "Saiba Mais". Para exemplificar, o módulo "O Universo" contém as seguintes seções: "O Universo visto pelo homem", "Conhecendo o Sistema Solar", "Indo além do Sistema Solar", "Nossa Galáxia, a Via-Láctea" e "Indo mais além, a imensidão do Universo". A seção "Conhecendo o Sistema Solar", por sua vez, tem os seguintes temas: "A origem do Sistema Solar", "O Sol", "Os planetas", "Satélites, asteróides, cometas e outros bichos..." e "O Sistema Solar em números". Cada texto é repleto de imagens, quadros, desenhos, esquemas, etc, além de passatempos ao final de cada seção, incluindo jogos interativos, quadrinhos e curiosidades, que auxiliam o aprendizado de forma divertida. Apresentamos neste trabalho as idéias gerais que permearam a produção da exposição, e uma viagem pelo multimídia para exemplificar sua estrutura e conteúdo. O multimídia será posteriormente disponibilizado para o público externo pela página eletrônica do MAst e/ou por intermédio de uma publicação comercial.

Ferromagnetism in UCo1-xMnxAl and UCo1-xVxAl

NASA Astrophysics Data System (ADS)

Izmaylov, M.; Rafaja, D.; Sechovský, V.; Andreev, A. V.

2002-01-01

UCoAl is an itinerant 5 f-electron metamagnet with a tiny critical field of transition B c≈0.4 T (at 1.3 K). Critical magnetic parameters of this material are strongly sensitive to chemical environment of U atoms. We present results of a pilot study of formation, crystal structure and magnetism of UCo1-xTxAl compounds for T=Mn and V, x≤0.1. All these compounds have been found to be isostructural with the parent compound. Already for x=0.01 in both systems a spontaneous magnetization M s has been observed at low temperatures. Anomalies in the AC susceptibility as a function of temperature point to T c≈28 and 25 K respectively for Mn and V doping. The ferromagnetism induced in UCo1-xTxAl compounds due to a substitution of light transition metal for Co is discussed within a model considering effects of varying 5 f-ligand hybridization on the stability of U 5 f-moment and on exchange interactions.

"Estudio tribologico de aceros para moldes. Aplicacion al moldeo por inyeccion de polibutilentereftalato reforzado con fibra de vidrio"

NASA Astrophysics Data System (ADS)

Martinez Mateo, Isidoro Jose

Mould materials for injection moulding of polymers and polymer-matrix composites represent a relevant industrial economic sector due to the large quantity of pieces and components processed. The material selection for mould manufacturing, its composition and heat treatment, the hardening procedures and machining and finishing processes determine the service performance and life of the mould. In the first part of the present study, the relationship between the hardness and microstructure and the wear resistance of mould steels from large blocks has been studied by pin-on-disc tests, studying the main wear mechanisms. In order to determine the surface damage on mould steels under real injection conditions, different commercial steels have been studied by measuring the variation of surface roughness with the number of injected pieces with different reinforcement percentages and different mould geometries, by using optical profilometry and scanning electron microscopy techniques. It was important to determine the variation of surface roughness of the moulded pieces with the number of injection operations. The materials used were polybutyleneterephthalate pure and reinforced with either 20% or 50% glass fibre. For the different mould designs, the evolution of the glass fibre orientation with injection flow has been determined by image analysis and related to roughness changes and surface damage, both of the composite parts and of the mould steel surface. Finally, the abrasion resistance of the composite parts has been studied by scratch tests as a function of the number of injected parts and of the scratch direction with respect to injection flow and glass fibre orientation. Los materiales para moldes de inyeccion de polimeros y materiales compuestos representan un sector economicamente muy relevante debido al gran aumento del numero de componentes fabricados a partir de materiales polimericos obtenidos mediante moldeo por inyeccion. La seleccion del material para la

Serological evidence of arboviral infection and self-reported febrile illness among U.S. troops deployed to Al Asad, Iraq.

PubMed

Riddle, M S; Althoff, J M; Earhart, K; Monteville, M R; Yingst, S L; Mohareb, E W; Putnam, S D; Sanders, J W

2008-05-01

Understanding the epidemiology of current health threats to deployed U.S. troops is important for medical assessment and planning. As part of a 2004 study among U.S. military personnel deployed to Al Asad Air Base, in the western Anbar Province of Iraq, over 500 subjects were enrolled, provided a blood specimen, and completed a questionnaire regarding history of febrile illness during this deployment (average approximately 4 months in country). This mid-deployment serum was compared to pre-deployment samples (collected approximately 3 months prior to deployment) and evaluated for seroconversion to a select panel of regional arboviral pathogens. At least one episode of febrile illness was reported in 84/504 (17%) of the troops surveyed. Seroconversion was documented in nine (2%) of deployed forces tested, with no association to febrile illness. Self-reported febrile illness was uncommon although often debilitating, and the risk of illness due to arbovirus infections was relatively low.

Advances in Laser Microprobe (U-Th)/He Geochronology

NASA Astrophysics Data System (ADS)

van Soest, M. C.; Monteleone, B. D.; Boyce, J. W.; Hodges, K. V.

2008-12-01

The development of the laser microprobe (U-Th)/He dating method has the potential to overcome many of the limitations that affect conventional (U-Th)/He geochronology. Conventional single- or multi-crystal (U- Th)/He geochronology requires the use of pristine, inclusion-free, euhedral crystals. Furthermore, the ages that are obtained require corrections for the effects of zoning and alpha ejection based on an ensemble of assumptions before interpretation of their geological relevance is possible. With the utilization of microbeam techniques many of the limitations of conventional (U-Th)/He geochronology can either be eliminated by careful spot selection or accounted for by detailed depth profiling analyses of He, U and Th on the same crystal. Combined He, Th, and U depth profiling on the same crystal potentially even offers the ability to extract thermal histories from the analyzed grains. Boyce et al. (2006) first demonstrated the laser microprobe (U-Th)/He dating technique by successfully dating monazite crystals using UV laser ablation to liberate He and determined U and Th concentrations using a Cameca SX-Ultrachron microprobe. At Arizona State University, further development of the microprobe (U-Th)/He dating technique continues using an ArF Excimer laser connected to a GVI Helix Split Flight Tube noble gas mass spectrometer for He analysis and SIMS techniques for U and Th. The Durango apatite age standard has been successfully dated at 30.7 +/- 1.7 Ma (2SD). Work on dating zircons by laser ablation is currently underway, with initial results from Sri Lanka zircon at 437 +/- 14 Ma (2SD) confirmed by conventional (U-Th)/He analysis and in agreement with the published (U-Th)/He age of 443 +/- 9 Ma (2SD) for zircons from this region in Sri Lanka (Nasdala et al., 2004). The results presented here demonstrate the laser microprobe (U-Th)/He method as a powerful tool that allows application of (U- Th)/He dating to areas of research such as detrital apatite and zircon

Al-Qaeda Core: A Case Study

DTIC Science & Technology

2017-10-01

near-simultaneous bombings of the U.S. embassies in Kenya and Tanzania in August 1998 that killed 224 people and wounded more than 5,000; the October...Yemeni Al-Qaeda members attempted unsuccessfully to bomb the USS The Sullivans, anchored in Yemen’s port of Aden. But ten months later, Al-Qaeda... bombing of a synagogue in Tunisia, Al-Qaeda operatives carried out major attacks in Casablanca (May 16, 2003), Istanbul (December 20, 2003), Madrid

Reaction paths and host phases of uranium isotopes (235U; 238U), Saanich Inlet

NASA Astrophysics Data System (ADS)

Amini, M.; Holmden, C. E.; Francois, R. H.

2009-12-01

preferentially adsorbed [5]. Whether plankton mediated chemical reduction or scavenging causes this fractionation will be further investigated by leaching experiments on sediment trap samples. By contrast, weak acidic leachates (at pH 6) of suboxic bottom sediments, tend towards higher δ238U values. For oxic sediments, U contents of this fraction were below detection limit. Stronger leaching at pH 3 removed most of the uranium from suboxic and oxic sediments. For oxic sediments, this fraction yields the seawater δ238U signature, while the U released from the suboxic sample is about 0.2‰ heavier. This matches the value for previously reported bulk analyses of suboxic sediments [1] implying that the reduced sedimentary U is released by this treatment,. Major and trace element analyses and XRD patterns will help relating this fraction to a specific mineral or reactive phase. [1] Weyer et al. (2007) GCA 72, 345-399. [2] Stirling et al. (2007) EPSL 264, 208-225. [3] Schauble (2007) GCA 71, 2170-2189. [4] Rademacher et al. (2006) Environ. Sci. Technol. 40,6943-6948. [5] Wasylenki (2009) GCA A1419.

Growth and characterization of n-AlGaN 1-D structures with varying Al composition using u-GaN seeds

NASA Astrophysics Data System (ADS)

Kang, San; Chatterjee, Uddipta; Um, Dae-Young; Seo, In Seok; Lee, Cheul-Ro

2017-12-01

Like all the ternary alloys in III-nitride materials family, aluminum gallium nitride (AlGaN) has unique band gap tuning property which enables the alloy to be suitable for many opto-electronic applications. The direct band gap of AlGaN can be tuned from 3.4 to 6.2 eV by changing the composition. In this article, the growth of ternary n-AlGaN micro and nano structures on Si (1 1 1) substrate is demonstrated via 2-step growth method employing metal organic chemical vapor deposition. During the growth flow of Trimethygallium is varied to modulate the final Al/Ga ratio. After the growth, various morphological, crystalline and optical characterizations are carried out to probe in the properties of the grown structures. Recorded X-ray diffraction patterns reveal that the realized structures are wurtzite single crystalline n-AlGaN having a near homogeneous Al distribution and validated by energy dispersive X-ray spectroscopy. Low temperature cathodoluminescence spectra show band edge emission in deep UV region which enables the grown n-AlGaN structures to efficiently find opto-electronic applications in the aforementioned region. Finally, planar photoconductive devices are fabricated using the grown 1-D structures and photocurrent evolution is measured. Structure bearing highest Al content shows a manifold enhancement in photo activity compared to other grown samples. Absolute photoresponsivities of the grown samples are calculated to be 301.47, 116 and 38.13 mA/W which is in accord with the findings of low temperature cathodoluminescence investigation. Therefore, it can be concluded that the successful realization of n-AlGaN 1-D structures varying Al content facilitates the further developments of the field concerning nano- and opto-electronic devices.

CNEA/ANL collaboration program to develop an optimized version of DART validation and assessment by means of U{sub 3}Si{sub x} and U{sub 3}O{sub 8-}Al dispersed CNEA miniplate irradiation behavior.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solis, D.

1998-10-16

The DART code is based upon a thermomechanical model that can predict swelling, recrystallization, fuel-meat interdiffusion and other issues related with MTR dispersed FE behavior under irradiation. As a part of a common effort to develop an optimized version of DART, a comparison between DART predictions and CNEA miniplates irradiation experimental data was made. The irradiation took place during 1981-82 for U3O8 miniplates and 1985-86 for U{sub 3}Si{sub x} at Oak Ridge Research Reactor (ORR). The microphotographs were studied by means of IMAWIN 3.0 Image Analysis Code and different fission gas bubbles distributions were obtained. Also it was possible tomore » find and identify different morphologic zones. In both kinds of fuels, different phases were recognized, like particle peripheral zones with evidence of Al-U reaction, internal recrystallized zones and bubbles. A very good agreement between code prediction and irradiation results was found. The few discrepancies are due to local, fabrication and irradiation uncertainties, as the presence of U{sub 3}Si phase in U{sub 3}Si{sub 2} particles and effective burnup.« less

Effectiveness of U.S. Policies for Al Shabaab

DTIC Science & Technology

2014-06-13

somalia-oil-exploration-idUSL6E8L2O7D20121002 (accessed 10 March 2014). 82Michelle Nichols and Louis Charbonneau , “Exclusive: Western oil exploration in...Michelle, and Louis Charbonneau . “Exclusive: Western oil exploration in Somalia may spark conflict – U.N. report.” Chicago Tribune, 17 July 2013. Perlez

MARTINS: A foam/film flow model for molten material relocation in HWRs with U-Al-fueled multi-tube assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalimullah

1994-03-01

Some special purpose heavy-water reactors (EM) are made of assemblies consisting of a number of coaxial aluminum-clad U-Al alloy fuel tubes and an outer Al sleeve surrounding the fuel tubes. The heavy water coolant flows in the annular gaps between the circular tubes. Analysis of severe accidents in such reactors requires a model for predicting the behavior of the fuel tubes as they melt and disrupt. This paper describes a detailed, mechanistic model for fuel tube heatup, melting, freezing, and molten material relocation, called MARTINS (Melting and Relocation of Tubes in Nuclear subassembly). The paper presents the modeling of themore » phenomena in MARTINS, and an application of the model to analysis of a reactivity insertion accident. Some models are being developed to compute gradual downward relocation of molten material at decay-heat power levels via candling along intact tubes, neglecting coolant vapor hydrodynamic forces on molten material. These models are inadequate for high power accident sequences involving significant hydrodynamic forces. These forces are included in MARTINS.« less

78 FR 32443 - United States, et al. v. Cinemark Holdings, Inc., et al.; Proposed Final Judgment and Competitive...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-30

... DEPARTMENT OF JUSTICE Antitrust Division United States, et al. v. Cinemark Holdings, Inc., et al.; Proposed Final Judgment and Competitive Impact Statement Notice is hereby given pursuant to the Antitrust Procedures and Penalties Act, 15 U.S.C. 16(b)-(h), that a proposed Final Judgment, Hold Separate Stipulation and Order and Competitive Impact...

The effect of aluminum additions on the oxidation resistance of U 3Si 2

DOE PAGES

Wood, E. Sooby; White, J. T.; Nelson, A. T.

2017-04-01

The effect of aluminum additions to U 3Si 2 is investigated in this paper as a means to improve the oxidation resistance of this nuclear fuel form. Four U-Si-Al compositions have been synthesized and characterized using scanning electron microscopy, energy dispersive spectroscopy, and x-ray diffraction. The onsets of breakaway oxidation are identified in air thermal ramp tests using thermogravimetric analysis. The final oxidation products following 1000° C air exposure are identified using x-ray diffraction and compared to those of UO 2 and U metal oxidized in the same manner. Finally, thermogravimetric data acquired in this study indicates that increasing amountsmore » of Al in U 3Si 2 further delays the onset of breakaway oxidation, providing enhanced oxidation resistance in air. Al 2O 3 formation on U 3Al 2Si 3 is observed following a heat treatment performed at 500° C in air, demonstrating the potential of Al additions to improve the oxidation resistance of U 3Si 2.« less

The effect of aluminum additions on the oxidation resistance of U 3Si 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, E. Sooby; White, J. T.; Nelson, A. T.

The effect of aluminum additions to U 3Si 2 is investigated in this paper as a means to improve the oxidation resistance of this nuclear fuel form. Four U-Si-Al compositions have been synthesized and characterized using scanning electron microscopy, energy dispersive spectroscopy, and x-ray diffraction. The onsets of breakaway oxidation are identified in air thermal ramp tests using thermogravimetric analysis. The final oxidation products following 1000° C air exposure are identified using x-ray diffraction and compared to those of UO 2 and U metal oxidized in the same manner. Finally, thermogravimetric data acquired in this study indicates that increasing amountsmore » of Al in U 3Si 2 further delays the onset of breakaway oxidation, providing enhanced oxidation resistance in air. Al 2O 3 formation on U 3Al 2Si 3 is observed following a heat treatment performed at 500° C in air, demonstrating the potential of Al additions to improve the oxidation resistance of U 3Si 2.« less

Delegitimizing Al-Qaeda: A Jihad-Realist Approach

DTIC Science & Technology

2012-03-01

However distasteful to U.S. national security de- cisionmakers, the presumption of Islamic suprema- cism and a past-perfect Islamic utopian “ golden ...Islamic glorious golden age. Third, an ac- count of “The Fall” is provided that is largely a dystopian odyssey involving Western cultural modernity...LIKEWISE AGAINST HIM . . . AL-FARBEK AL-ROKN, Abu Bakr Al-Makee (Simon Reeve, The New Jackals : Ramzi Yousef, Osama bin Laden, and the Future of Terror

Exploratory study of fission product yields of neutron-induced fission of 235U , 238U , and 239Pu at 8.9 MeV

NASA Astrophysics Data System (ADS)

Bhatia, C.; Fallin, B. F.; Gooden, M. E.; Howell, C. R.; Kelley, J. H.; Tornow, W.; Arnold, C. W.; Bond, E.; Bredeweg, T. A.; Fowler, M. M.; Moody, W.; Rundberg, R. S.; Rusev, G. Y.; Vieira, D. J.; Wilhelmy, J. B.; Becker, J. A.; Macri, R.; Ryan, C.; Sheets, S. A.; Stoyer, M. A.; Tonchev, A. P.

2015-06-01

Using dual-fission chambers each loaded with a thick (200 -400 -mg /c m2) actinide target of 235 ,238U or 239Pu and two thin (˜10 -100 -μ g /c m2) reference foils of the same actinide, the cumulative yields of fission products ranging from 92Sr to 147Nd have been measured at En= 8.9 MeV . The 2H(d ,n ) 3He reaction provided the quasimonoenergetic neutron beam. The experimental setup and methods used to determine the fission product yield (FPY) are described, and results for typically eight high-yield fission products are presented. Our FPYs for 235U(n ,f ) , 238U(n ,f ) , and 239Pu(n ,f ) at 8.9 MeV are compared with the existing data below 8 MeV from Glendenin et al. [Phys. Rev. C 24, 2600 (1981), 10.1103/PhysRevC.24.2600], Nagy et al. [Phys. Rev. C 17, 163 (1978), 10.1103/PhysRevC.17.163], Gindler et al. [Phys. Rev. C 27, 2058 (1983), 10.1103/PhysRevC.27.2058], and those of Mac Innes et al. [Nucl. Data Sheets 112, 3135 (2011), 10.1016/j.nds.2011.11.009] and Laurec et al. [Nucl. Data Sheets 111, 2965 (2010), 10.1016/j.nds.2010.11.004] at 14.5 and 14.7 MeV, respectively. This comparison indicates a negative slope for the energy dependence of most fission product yields obtained from 235U and 239Pu , whereas for 238U the slope issue remains unsettled.

Effects of Al-Impurity Type on Formation Energy, Crystal Structure, Electronic Structure, and Optical Properties of ZnO by Using Density Functional Theory and the Hubbard-U Method.

PubMed

Wu, Hsuan-Chung; Chen, Hsing-Hao; Zhu, Yu-Ren

2016-08-01

We systematically investigated the effects of Al-impurity type on the formation energy, crystal structure, charge density, electronic structure, and optical properties of ZnO by using density functional theory and the Hubbard-U method. Al-related defects, such as those caused by the substitution of Zn and O atoms by Al atoms (Al s(Zn) and Al s(O) , respectively) and the presence of an interstitial Al atom at the center of a tetrahedron (Al i(tet) ) or an octahedron (Al i(oct) ), and various Al concentrations were evaluated. The calculated formation energy follows the order E f (Al s(Zn) ) < E f (Al i(tet) ) < E f (Al i(oct) ) < E f (Al s(O) ). Electronic structure analysis showed that the Al s(Zn) , Al s(O) , Al i(tet) , and Al i(oct) models follow n -type conduction, and the optical band gaps are higher than that of pure ZnO. The calculated carrier concentrations of the Al s(O) and Al i(tet) /Al i(oct) models are higher than that of the Al s(Zn) model. However, according to the curvature of the band structure, the occurrence of interstitial Al atoms or the substitution of O atoms by Al atoms results in a high effective mass, possibly reducing the carrier mobility. The average transmittance levels in the visible light and ultraviolet (UV) regions of the Al s(Zn) model are higher than those of pure ZnO. However, the presence of an interstitial Al atom within the ZnO crystal reduces transmittance in the visible light region; Al s(O) substantially reduces the transmittance in the visible light and UV regions. In addition, the properties of ZnO doped with various Al s(Zn) concentrations were analyzed.

Examining Changing American Perceptions of the Terrorist Threat: From the Oklahoma City Bombing to Al Qaeda

DTIC Science & Technology

2017-12-01

CHANGING AMERICAN PERCEPTIONS OF THE TERRORIST THREAT: FROM THE OKLAHOMA CITY BOMBING TO AL QAEDA by Eli U.S. Persons December 2017 Thesis...THREAT: FROM THE OKLAHOMA CITY BOMBING TO AL QAEDA 5. FUNDING NUMBERS 6. AUTHOR(S) Eli U.S. Persons 7. PERFORMING ORGANIZATION NAME(S) AND...THREAT: FROM THE OKLAHOMA CITY BOMBING TO AL QAEDA Eli U.S. Persons Major, United States Air Force B.S., United States Air Force Academy, 2005

In situ isotopic studies of the U-depleted Allende CAI Curious Marie: Pre-accretionary alteration and the co-existence of 26Al and 36Cl in the early solar nebula

NASA Astrophysics Data System (ADS)

Tang, Haolan; Liu, Ming-Chang; McKeegan, Kevin D.; Tissot, Francois L. H.; Dauphas, Nicolas

2017-06-01

The isotopic composition of oxygen as well as 26Al-26Mg and 36Cl-36S systematics were studied in Curious Marie, an aqueously altered Allende CAI characterized by a Group II REE pattern and a large 235U excess produced by the decay of short-lived 247Cm. Oxygen isotopic compositions in the secondary minerals of Curious Marie follow a mass-dependent fractionation line with a relatively homogenous depletion in 16O (Δ17O of -8‰) compared to unaltered minerals of CAI components. Both Mg and S show large excesses of radiogenic isotopes (26Mg∗ and 36S∗) that are uniformly distributed within the CAI, independent of parent/daughter ratio. A model initial 26Al/27Al ratio [(6.2 ± 0.9) × 10-5], calculated using the bulk Al/Mg ratio and the uniform δ26Mg∗ ∼ +43‰, is similar to the canonical initial solar system value within error. The exceptionally high bulk Al/Mg ratio of this CAI (∼95) compared to other inclusions is presumably due to Mg mobilization by fluids. Therefore, the model initial 26Al/27Al ratio of this CAI implies not only the early condensation of the CAI precursor but also that aqueous alteration occurred early, when 26Al was still at or near the canonical value. This alteration event is most likely responsible for the U depletion in Curious Marie and occurred at most 50 kyr after CAI formation, leading to a revised estimate of the early solar system 247Cm/235U ratio of (5.6 ± 0.3) × 10-5. The Mg isotopic composition in Curious Marie was subsequently homogenized by closed-system thermal processing without contamination by chondritic Mg. The large, homogeneous 36S excesses (Δ36S∗ ∼ +97‰) detected in the secondary phases of Curious Marie are attributed to 36Cl decay (t1/2 = 0.3 Myr) that was introduced by Cl-rich fluids during the aqueous alteration event that led to sodalite formation. A model 36Cl/35Cl ratio of (2.3 ± 0.6) × 10-5 is calculated at the time of aqueous alteration, translating into an initial 36Cl/35Cl ratio of ∼1.7-3 �

Reply to Comment on "Zircon U-Th-Pb dating using LA-ICP-MS: Simultaneous U-Pb and U-Th dating on the 0.1 Ma Toya Tephra, Japan"

NASA Astrophysics Data System (ADS)

Ito, Hisatoshi

2015-04-01

Guillong et al. (2015) mentioned that corrections for abundance sensitivity for 232Th and molecular zirconium sesquioxide ions (Zr2O3+) are critical for reliable determination of 230Th abundances in zircon for LA-ICP-MS analyses. There is no denying that more rigorous treatments are necessary to obtain more reliable ages than those in Ito (2014). However, as shown in Fig. 2 in Guillong et al. (2015), the uncorrected (230Th)/(238U) for reference zircons except for Mud Tank are only 5-20% higher than unity. Since U abundance of Toya Tephra zircons that have U-Pb ages < 1 Ma is in-between that of FCT and Plesovice, the overestimation of 230Th by both abundance sensitivity and molecular interferences is expected to be 5-20% for the Toya Tephra. Moreover Ito (2014) obtained U-Th ages of the Toya Tephra by comparison with Fish Canyon Tuff (FCT) data. Because both the FCT and the Toya Tephra have similar trends of overestimation of 230Th, the effect of overestimation of 230Th to cause overestimation of U-Th age should be cancelled out or negligible. Therefore the pivotal conclusion in Ito (2014) that simultaneous U-Pb and U-Th dating using LA-ICP-MS is possible and useful for Quaternary zircons holds true.

Computational materials design of negative effective U system in the hole-doped Delafossite of CuAlO2, AgAlO2 and AuAlO2

NASA Astrophysics Data System (ADS)

Nakanishi, Akitaka; Fukushima, Tetsuya; Uede, Hiroki; Katayama-Yoshida, Hiroshi

2015-03-01

In order to realize the super-high-TC superconductors (TC>1,000K) based on the general design rules for the negative Ueff system, we have performed computational materials design for theUeff<0 system in the hole-doped two-dimensional (2D) Delafossite CuAlO2, AgAlO2 and AuAlO2 from the first principles. We find the interesting chemical trend of TC in 2D and 3D systems; where the TC increases exponentially in the weak coupling regime (|Ueff (-0.44eV)|< W(2eV), W is the band width) for hole-doped CuFeS2, then the TC goes through a maximum when |Ueff (-4.88eV, -4.14eV)| ~ W (2.8eV, 3.5eV) for hole-doped AgAlO2 and AuAlO2, and the TC decreases with increasing |Ueff|in strong coupling regime, where |Ueff (-4.53eV)|> W(1.7eV) for hole-doped CuAlO2

Irradiation behavior of the interaction product of U-Mo fuel particle dispersion in an Al matrix

NASA Astrophysics Data System (ADS)

Kim, Yeon Soo; Hofman, G. L.

2012-06-01

Irradiation performance of U-Mo fuel particles dispersed in Al matrix is stable in terms of fuel swelling and is suitable for the conversion of research and test reactors from highly enriched uranium (HEU) to low enriched uranium (LEU). However, tests of the fuel at high temperatures and high burnups revealed obstacles caused by the interaction layers forming between the fuel particle and matrix. In some cases, fission gas filled pores grow and interconnect in the interdiffusion layer resulting in fuel plate failure. Postirradiation observations are made to examine the behavior of the interdiffusion layers. The interdiffusion layers show a fluid-like behavior characteristic of amorphous materials. In the amorphous interdiffusion layers, fission gas diffusivity is high and the material viscosity is low so that the fission gas pores readily form and grow. Based on the observations, a pore formation mechanism is proposed and potential remedies to suppress the pore growth are also introduced.

U-Th Burial Dates on Ostrich Eggshell

NASA Astrophysics Data System (ADS)

Sharp, W. D.; Fylstra, N. D.; Tryon, C. A.; Faith, J. T.; Peppe, D. J.

2015-12-01

to the U-Th data. The oldest OES we have analyzed yields a U-Th burial date of ~140 ka, indicating that U-Th burial dating of OES may be applicable throughout the Late Pleistocene. 1. Magee, J.W. et al. (2009) Quatern. Geochron. 4, 84-89. 2. Johnson, B.J. et al. (1998) Geochim. Cosmochim. Acta 62, 2451-2461. 3. Miller, G.H. et al. (2005) Science 309, 287-290.

Evidence that C9ORF72 Dipeptide Repeat Proteins Associate with U2 snRNP to Cause Mis-splicing in ALS/FTD Patients.

PubMed

Yin, Shanye; Lopez-Gonzalez, Rodrigo; Kunz, Ryan C; Gangopadhyay, Jaya; Borufka, Carl; Gygi, Steven P; Gao, Fen-Biao; Reed, Robin

2017-06-13

Hexanucleotide repeat expansion in the C9ORF72 gene results in production of dipeptide repeat (DPR) proteins that may disrupt pre-mRNA splicing in amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD) patients. At present, the mechanisms underlying this mis-splicing are not understood. Here, we show that addition of proline-arginine (PR) and glycine-arginine (GR) toxic DPR peptides to nuclear extracts blocks spliceosome assembly and splicing, but not other types of RNA processing. Proteomic and biochemical analyses identified the U2 small nuclear ribonucleoprotein particle (snRNP) as a major interactor of PR and GR peptides. In addition, U2 snRNP, but not other splicing factors, mislocalizes from the nucleus to the cytoplasm both in C9ORF72 patient induced pluripotent stem cell (iPSC)-derived motor neurons and in HeLa cells treated with the toxic peptides. Bioinformatic studies support a specific role for U2-snRNP-dependent mis-splicing in C9ORF72 patient brains. Together, our data indicate that DPR-mediated dysfunction of U2 snRNP could account for as much as ∼44% of the mis-spliced cassette exons in C9ORF72 patient brains. Copyright © 2017 The Author(s). Published by Elsevier Inc. All rights reserved.

Background reduction in 236U/238U measurements

NASA Astrophysics Data System (ADS)

Buompane, Raffaele; De Cesare, Mario; De Cesare, Nicola; Di Leva, Antonino; D'Onofrio, Antonio; Fifield, L. Keith; Fröhlich, Michaela; Gialanella, Lucio; Marzaioli, Fabio; Sabbarese, Carlo; Terrasi, Filippo; Tims, Stephen; Wallner, Anton

2015-10-01

The measurements of actinide isotopic ratios, in particular 236U/238U, in environmental samples requires high sensitivity. In particular, special effort must be devoted to the suppression of interfering nuclides, such as 235,238U, when measuring 236U. At the AMS facility of CIRCE, isotopic ratios down to ∼10-10 are currently measured using a gas E - ΔE detector. In order to push this limit lower towards natural levels, a time-of-flight system is used, featuring a micro-channel plate start detector and a Si stop detector. As the mass resolution of the latter is limited by the layout, an attempt to reduce the abundant isotope interference by other means has been undertaken. In this study, we report preliminary results on the characterization of the presence of molecular interferences when using UO-, UC- and UC2- as injected molecular ions. In particular the possibility to stabilize the current yield from carbide cathodes has been investigated: it was found that the best cathode preparation procedure is obtained pressing U salts baked at 800 °C mixed with graphite and Al powder. Moreover, the 238U background in 236U measurements is strongly reduced injecting UC- ions, as verified using a time-of-flight detection system. On the other hand, 235U interference is larger with respect to UO- injection, but this increase is smaller than expected on the basis of abundances of 13C and 17O in UC and UC2 molecules on one side and UO, on the other.

A first principles investigation of electron transfer between Fe(II) and U(VI) on insulating Al- vs. semiconducting Fe-oxide surfaces via the proximity effect

NASA Astrophysics Data System (ADS)

Taylor, S. D.; Marcano, M. C.; Becker, U.

2017-01-01

This study investigates how the intrinsic chemical and electronic properties of mineral surfaces and their associated electron transfer (ET) pathways influence the reduction of U(VI) by surface-associated Fe(II). Density functional theory (DFT), including the Hubbard U correction to the exchange-correlation functional, was used to investigate sorption/redox reactions and ET mechanisms between Fe(II) and U(VI) coadsorbed on isostructural, periodic (0 0 1) surfaces of the insulator corundum (α-Al2O3) vs. the semiconductor hematite (α-Fe2O3). Furthermore, the coadsorbed Fe(II) and U(VI) ions are spatially separated from one another on the surfaces (⩾5.9 Å) to observe whether electronic-coupling through the semiconducting hematite surface facilitates ET between the adsorbates, a phenomenon known as the proximity effect. The calculations show that the different chemical and electronic properties between the isostructural corundum and hematite (0 0 1) surfaces lead to considerably different ET mechanisms between Fe(II) and U(VI). ET on the insulating corundum (0 0 1) surface is limited by the adsorbates' structural configuration. When Fe(II) and U(VI) are spatially separated and do not directly interact with one another (e.g. via an inner-sphere complex), U(VI) reduction by Fe(II) cannot occur as there is no physical pathway enabling ET between the adsorbates. In contrast to the insulating corundum (0 0 1) surface, the hematite (0 0 1) surface can potentially participate in ET reactions due to the high number of electron acceptor sites from the Fe d-states near the Fermi level at the hematite surface. The adsorption of Fe(II) also introduces d-states near the Fermi level as well as shifts unoccupied d-states of the Fe cations at the hematite surface to lower energies, making the surface more conductive. In turn, electronic coupling through the surface can link the spatially separated adsorbates to one another and provide distinct ET pathways for an electron from Fe

Japan-U.S. Relations: Issues for Congress

DTIC Science & Technology

2007-09-27

operations against Al Qaeda and the Taliban in Afghanistan. The latter mainly took the form of at-sea replenishment of fuel oil and water to U.S., British...creating a scandal over the Agricultural Ministry’s handling of the issue (several more Japanese BSE cases have since emerged). Japan had retained the...procedures U.S. and Japanese officials had agreed upon. U.S. Secretary of Agriculture Mike Johanns expressed regret that the prohibited material had

Effect of Humic Substances on the Trapping and Transformations of U(VI) by Ferrihydrite

NASA Astrophysics Data System (ADS)

Dublet, G.; Brown, G. E.; Bargar, J.; Fendorf, S. E.; Janot, N.

2013-12-01

with macroscopic uptake measurements to study the effect of this model humic acid on U uptake by Fh in these batch experimental systems. Results from this study will be presented and discussed mainly in terms of the affinity of U towards ESHA vs. Fh under the different conditions tested. [1] Campbell K.M. et al. (2012) Applied Geochemistry 27, 1499-1511 [2] Maher K. et al. (2012) Inorganic Chemistry 52, 3510-3532. [3] Means J.L. and Crerar D.A. (1978) Science 200, 1477-1481 [4] Ludwig C. et al. (1995) Nature 375, 44-47 [5] Gu B. et al. (2005) 39, 5268-5275 [6] Stewart B.D. et al. (2009) Environmental Science & Technology 43, 4922-4927 [7] Sachs S. and Bernhard G. (2011) Journal of Radioanalytical and Nuclear Chemistry 290, 17-29 [8] Nico P.S. et al. (2009) Environmental Science & Technology 43, 7391-7396 [9] Boland D.D. et al. (2011) Environmental Science & Technology 45, 1327-1333 [10] Gustafsson J.P. et al. (2009) Applied Geochemistry 24, 454-462 [11] Payne T.E. et al. (1996) Radiochimica Acta 74, 239-243

Synroc-D Type Ceramics Produced by Hot Isostatic Pressing and Cold Crucible Melting for Immobilisation of (Al, U) Rich Nuclear Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vance, Eric R.; La Robina, Michael; Li, Huijun

2007-07-01

A synroc-D ceramic consisting mostly of spinel, hollandite, pyrochlore-structured CaUTi{sub 2}O{sub 7}, UO{sub 2}, and Ti-rich regions shows promise for immobilisation of a HLW containing mainly Al and U, together with fission products. Ceramics with virtually zero porosities and waste loadings of 50-60 wt% on an oxide basis were prepared by cold crucible melting (CCM) at {approx}1500 deg. C, and also by subsolidus hot isostatic pressing (HIP) at 1100 deg. C to prevent volatile losses. PCT leaching test values for Cs were < 13 g/L, with all other normalised elemental extractions being well below 1 g/L. (authors)

Fabrication of hierarchical core-shell polydopamine@MgAl-LDHs composites for the efficient enrichment of radionuclides

NASA Astrophysics Data System (ADS)

Zhu, Kairuo; Lu, Songhua; Gao, Yang; Zhang, Rui; Tan, Xiaoli; Chen, Changlun

2017-02-01

Novel hierarchical core/shell structured polydopamine@MgAl-layered double hydroxides (PDA@MgAl-LDHs) composites involving MgAl-layered double hydroxide shells and PDA cores were fabricated thought one-pot coprecipitation assembly and methodically characterized by X-ray diffraction, Fourier transformed infrared spectroscopy, scanning/transmission electron microscopy, selected area electron diffraction, elemental mapping, thermogravimetric analysis and X-ray photoelectron spectroscopy technologies. U(VI) and Eu(III) sorption experiments showed that the PDA@MgAl-LDHs exhibited higher sorption ability with a maximum sorption capacity of 142.86 and 76.02 mg/g at 298 K and pH 4.5, respectively. More importantly, according to XPS analyses, U(VI) and Eu(III) were sorbed on PDA@MgAl-LDHs via oxygen-containing functional groups, and the chemical affinity of U(VI) by oxygen-containing functional groups is higher than that of Eu(III). These observations show great expectations in the enrichment of radionuclides from aquatic environments by PDA@MgAl-LDHs.

EXAFS Reveals the Mechanism of U Isotope Fractionation During Adsorption to Mn Oxyhydroxide

NASA Astrophysics Data System (ADS)

Wasylenki, L. E.; Brennecka, G.; Bargar, J.; Weyer, S.; Anbar, A. D.

2010-12-01

subtle, but important differences in the U-O coordination shell between dissolved and adsorbed U. In particular, there is an increase in disorder in the bond distances to equatorial oxygens in the adsorbed complex. Our EXAFS data support our hypothesis that a difference in coordination chemistry drives the isotope effect observed in our experiments. The same mechanism may well explain the U isotope fractionation observed between seawater and hydrogenetic ferromanganese nodules, although a similar investigation of U isotope behavior during adsorption to Fe oxyhydroxides should be undertaken. [1] Weyer et al. (2008) GCA 72, 345. [2] Stirling et al. (2007) EPSL 264, 208. [3] Bopp et al. (2009) Geology, 37, 611. [4] Montoya-Pino et al. (2010) Geology 38, 315. [5] Brennecka et al. (2008) GCA 72(12) Suppl., A114.

Control of the U and Th behaviour in forest soils

NASA Astrophysics Data System (ADS)

Rihs, Sophie; Gontier, Adrien; Chabaux, François; Pelt, Eric; Turpault, Marie-Pierre

2015-04-01

U- and Th-series disequilibria and U, Th, Fe and Al speciation, were measured in several soil profiles from the experimental forest site of Breuil (Morvan, France) in order to address the impact of the vegetation on U and Th nuclides behaviour in soils. Thirty-five years after an experimental clear-felling of the native forest, the soil developed under two replacing mono-specific plantations (Oak and Douglas fir) were therefore compared to the undisturbed native forest soil. The analogous physical and chemical properties of these soils before the replacement were formerly demonstrated. Our results suggest that a shift in the Iron distribution seems to occur under the stand replaced by Oaks, with a significant replacement of Fe-bearing silicates by well crystallized Fe oxides. In contrast, such evolution was not demonstrated in the soils under Douglas fir. The concurrent loss of U and Th from the soils under Oak was tentatively related to the dissolution of Fe-bearing minerals. A mass balance calculation demonstrates that the observed increase in U oxalate-extracted fractions can quantitatively be explained through the entire profiles by a mere dissolution of up to 20% of U-Fe-bearing silicated minerals, without significant re-adsorption onto the amorphous Fe-Al oxides for U. Beside this primary release from Fe-bearing silicate minerals, the mobility of U and Th seems more likely controlled by Al phases rather than Fe oxides in surface layers during further pedogenic processes. Indeed, some of the U- and Th series disequilibria seem to be strongly related to Al dynamic in these layers. This relationship can be seen in the native forest profiles as well as in the replaced profiles, suggesting that this feature is not linked to the cover change. The redistribution of U and Th isotopes through these pedogenic processes therefore rule out the use of U-series for weathering rate determination in shallowest soils layers. In contrast, below 25 cm, the release of U and Th

Minimum pickup velocity ( U pu) of nanoparticles in gas-solid pneumatic conveying

NASA Astrophysics Data System (ADS)

Anantharaman, Aditya; van Ommen, J. Ruud; Chew, Jia Wei

2015-12-01

This paper is the first systematic study of the pneumatic conveying of nanoparticles. The minimum pickup velocity, U pu, of six nanoparticle species of different materials [i.e., silicon dioxide (SiO2), aluminum oxide (Al2O3), and titanium dioxide (TiO2)] and surfaces (i.e., apolar and polar) was determined by the weight loss method. Results show that (1) due to relative lack of hydrogen bonding, apolar nanoparticles had higher mass loss values at the same velocities, mass loss curves with accentuated S-shaped profiles, and lower U pu values, (2) among the three species, SiO2, which has the lowest Hamaker coefficient, exhibited the greatest discrepancy between apolar and polar surfaces with respect to both mass loss curves and U pu values, (3) U mf,polar/ U mf,apolar was between 1 and 3.5 times that of U pu,polar/ U pu,apolar due to greater extents of hydrogen bonding associated with U mf, (4) U pu values were at least an order-of-magnitude lower than that expected from the well-acknowledged U pu correlation (Kalman et al., Powder Technol 160:103-113, 2005) due to agglomeration, (5) although nanoparticles should be categorized as Zone III (Kalman et al. 2005) (or Geldart group C, Powder Technol 7:285-292, 1973), the nanoparticles, and primary and complex agglomerates agreed more with the Zone I (or Geldart group B) correlation.

Spin conversion of positronium in NiO/Al2O3 catalysts observed by coincidence Doppler broadening technique

NASA Astrophysics Data System (ADS)

Zhang, H. J.; Chen, Z. Q.; Wang, S. J.; Kawasuso, A.; Morishita, N.

2010-07-01

High-purity NiO/Al2O3 catalysts were prepared by mixing NiO and γ-Al2O3 nanopowders. X-ray diffraction patterns were measured to characterize the grain size and crystalline phase of the nanopowders. Positron-annihilation spectroscopy was used to study the microstructure and surface properties of the pores inside the NiO/Al2O3 catalysts. The positron lifetime spectrum comprises two short and two long lifetime components. The two long lifetimes τ3 and τ4 correspond to ortho-positronium (o-Ps) annihilated in microvoids and large pores, respectively. With increasing NiO content in the NiO/Al2O3 catalysts, both τ4 and its intensity I4 show continuous decrease. Meanwhile, the para-positronium (p-Ps) intensity, obtained from coincidence Doppler broadening spectra, increases gradually with NiO content. The different variation in o-Ps and p-Ps intensity suggests the ortho-para conversion of positronium in NiO/Al2O3 catalysts. X-ray photoelectron spectroscopy shows that Ni mainly exists in the form of NiO. The electron-spin-resonance measurements reveal that the ortho-para conversion of Ps is induced by the unpaired electrons of the paramagnetic centers of NiO.

TEM characterization of irradiated U-7Mo/Mg dispersion fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gan, J.; Keiser, D. D.; Miller, B. D.

This paper presents the results of transmission electron microscopy (TEM) characterization on neutron-irradiated samples taken from the low-flux and high-flux sides of the same fuel plate with U-7Mo fuel particles dispersed in Mg matrix with aluminum alloy Al6061 as cladding material that was irradiated edge-on to the core in the Advanced Test Reactor. The corresponding local fission density and fission rate of the fuel particles and the average fuel-plate centerline temperature for the low-flux and high-flux samples are estimated to be 3.7 × 10 21 f/cm 3, 7.4 × 10 14 f/cm 3/s and 123 °C, and 5.5 × 10more » 21 f/cm3, 11.0 × 10 14 f/cm 3/s and 158 °C, respectively. Complex interaction layers developed at the Al-Mg interface, consisting of Al 3Mg 2 and Al 12Mg 17 along with precipitates of MgO, Mg 2Si and FeAl 5.3. No interaction between Mg matrix and U-Mo fuel particle was identified. For the U-Mo fuel particles, at low fission density, small elongated bubbles wrapped around the clean areas with a fission gas bubble superlattice, which suggests that bubble coalescence is an important mechanism for converting the fission gas bubble superlattice to large bubbles. At high fission density, no bubbles or porosity were observed in the Mg matrix, and pockets of residual fission gas bubble superlattice were observed in the U-Mo fuel particle interior.« less

TEM characterization of irradiated U-7Mo/Mg dispersion fuel

DOE PAGES

Gan, J.; Keiser, D. D.; Miller, B. D.; ...

2017-07-15

This paper presents the results of transmission electron microscopy (TEM) characterization on neutron-irradiated samples taken from the low-flux and high-flux sides of the same fuel plate with U-7Mo fuel particles dispersed in Mg matrix with aluminum alloy Al6061 as cladding material that was irradiated edge-on to the core in the Advanced Test Reactor. The corresponding local fission density and fission rate of the fuel particles and the average fuel-plate centerline temperature for the low-flux and high-flux samples are estimated to be 3.7 × 10 21 f/cm 3, 7.4 × 10 14 f/cm 3/s and 123 °C, and 5.5 × 10more » 21 f/cm3, 11.0 × 10 14 f/cm 3/s and 158 °C, respectively. Complex interaction layers developed at the Al-Mg interface, consisting of Al 3Mg 2 and Al 12Mg 17 along with precipitates of MgO, Mg 2Si and FeAl 5.3. No interaction between Mg matrix and U-Mo fuel particle was identified. For the U-Mo fuel particles, at low fission density, small elongated bubbles wrapped around the clean areas with a fission gas bubble superlattice, which suggests that bubble coalescence is an important mechanism for converting the fission gas bubble superlattice to large bubbles. At high fission density, no bubbles or porosity were observed in the Mg matrix, and pockets of residual fission gas bubble superlattice were observed in the U-Mo fuel particle interior.« less

Adaptación al español y validación de criterio de una escala para la tamización de problemas emocionales y del comportamiento en la primera infancia.

PubMed

Cano, Luz Helena; Acosta, María Natalia; Pulido, Adriana

2018-05-01

Introducción. La detección temprana del riesgo de problemas emocionales y del comportamiento en niños puede contribuir al desarrollo de estrategias que promuevan la salud mental desde la primera infancia. En Colombia no existe una herramienta validada para dicha detección.Objetivos. Seleccionar, adaptar y establecer la validez de criterio de una escala de tamización de problemas emocionales y del comportamiento en niños menores de seis años.Materiales y métodos. A partir de una revisión de la literatura y un consenso de expertos, se seleccionó la herramienta Early Childhood Screening Assessment (ECSA). Posteriormente, se llevó a cabo su adaptación lingüística y se determinó la validez de criterio mediante una curva de características de recibidor-operador (Receiver Operating Characteristic, ROC), y se la comparó con el cuestionario Child Behavior Checklist (CBCL 1,5-5). En el estudio participaron 206 cuidadores de niños entre el año y medio y los seis años de edad de la ciudad de Tunja y el municipio de Sopó.Resultados. La puntuación del ECSA presentó una buena correlación con la puntuación t total del CBCL 1,5-5 (ro de Spearman=0,75; p<0,01). La escala ECSA tuvo una sensibilidad de 86 % y una especificidad de 82 % al establecer un punto de corte de 24 para la población estudiada.Conclusión. En este primer estudio de adaptación y validación de la versión en español de la escala ECSA, se detectaron buenos valores de sensibilidad y especificidad para la tamización de problemas emocionales y del comportamiento en la primera infancia.

Bicarbonate Impact on U(VI) Bioreduction in a Shallow Alluvial Aquifer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, Philip E.; Williams, Kenneth H.; Davis, James A.

Field-scale biostimulation and desorption tracer experiments conducted in a uranium (U) contaminated, shallow alluvial aquifer have provided insight into the coupling of microbiology, biogeochemistry, and hydrogeology that control U mobility in the subsurface. Initial experiments successfully tested the concept that Fe-reducing bacteria such as Geobacter sp. could enzymatically reduce soluble U(VI) to insoluble U(IV) during in situ electron donor amendment (Anderson et al. 2003, Williams et al. 2011). In parallel, in situ desorption tracer tests using bicarbonate amendment demonstrated rate-limited U(VI) desorption (Fox et al. 2012). These results and prior laboratory studies underscored the importance of enzymatic U(VI)-reduction and suggestedmore » the ability to combine desorption and bioreduction of U(VI). Here we report the results of a new field experiment in which bicarbonate-promoted uranium desorption and acetate amendment were combined and compared to an acetate amendment-only experiment in the same experimental plot. Results confirm that bicarbonate amendment to alluvial aquifer desorbs U(VI) and increases the abundance of Ca-uranyl-carbonato complexes. At the same time, that the rate of acetate-promoted enzymatic U(VI) reduction was greater in the presence of added bicarbonate in spite of the increased dominance of Ca-uranyl-carbonato aqueous complexes. A model-simulated peak rate of U(VI) reduction was ~3.8 times higher during acetate-bicarbonate treatment than under acetate-only conditions. Lack of consistent differences in microbial community structure between acetate-bicarbonate and acetate-only treatments suggest that a significantly higher rate of U(VI) reduction the bicarbonate-impacted sediment may be due to a higher intrinsic rate of microbial reduction induced by elevated concentrations of the bicarbonate oxyanion. The findings indicate that bicarbonate amendment may be useful in improving the engineered bioremediation of uranium in aquifers.« less

Bicarbonate impact on U(VI) bioreduction in a shallow alluvial aquifer

NASA Astrophysics Data System (ADS)

Long, Philip E.; Williams, Kenneth H.; Davis, James A.; Fox, Patricia M.; Wilkins, Michael J.; Yabusaki, Steven B.; Fang, Yilin; Waichler, Scott R.; Berman, Elena S. F.; Gupta, Manish; Chandler, Darrell P.; Murray, Chris; Peacock, Aaron D.; Giloteaux, Ludovic; Handley, Kim M.; Lovley, Derek R.; Banfield, Jillian F.

2015-02-01

Field-scale biostimulation and desorption tracer experiments conducted in a uranium (U) contaminated, shallow alluvial aquifer have provided insight into the coupling of microbiology, biogeochemistry, and hydrogeology that control U mobility in the subsurface. Initial experiments successfully tested the concept that Fe-reducing bacteria such as Geobacter sp. could enzymatically reduce soluble U(VI) to insoluble U(IV) during in situ electron donor amendment (Anderson et al., 2003; Williams et al., 2011). In parallel, in situ desorption tracer tests using bicarbonate amendment demonstrated rate-limited U(VI) desorption (Fox et al., 2012). These results and prior laboratory studies underscored the importance of enzymatic U(VI)-reduction and suggested the ability to combine desorption and bioreduction of U(VI). Here we report the results of a new field experiment in which bicarbonate-promoted uranium desorption and acetate amendment were combined and compared to an acetate amendment-only experiment in the same experimental plot. Results confirm that bicarbonate amendment to alluvial aquifer sediments desorbs U(VI) and increases the abundance of Ca-uranyl-carbonato complexes. At the same time, the rate of acetate-promoted enzymatic U(VI) reduction was greater in the presence of added bicarbonate in spite of the increased dominance of Ca-uranyl-carbonato aqueous complexes. A model-simulated peak rate of U(VI) reduction was ∼3.8 times higher during acetate-bicarbonate treatment than under acetate-only conditions. Lack of consistent differences in microbial community structure between acetate-bicarbonate and acetate-only treatments suggest that a significantly higher rate of U(VI) reduction in the bicarbonate-impacted sediment may be due to a higher intrinsic rate of microbial reduction induced by elevated concentrations of the bicarbonate oxyanion. The findings indicate that bicarbonate amendment may be useful in improving the engineered bioremediation of uranium in

Senegal: Background and U.S. Relations

DTIC Science & Technology

2012-04-11

Politique et Révolution Passive. ‘Sopi’ or not ‘Sopi’?” Politique Africaine, December 2004. 12 See, for example, Abdou Latif Coulibaly, Contes et ...regional presence of violent extremist groups. Al Qaeda in the Islamic Maghreb (AQIM), an criminal- terrorist network with ties to Al Qaeda and roots...FTF_2010_Implementation_Plan_Senegal.pdf. 27 U.N. Development Program and Government of Senegal, Changement Climatique, Sécurité Alimentaire et Développement Humain

Modeling a failure criterion for U–Mo/Al dispersion fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oh, Jae-Yong; Kim, Yeon Soo; Tahk, Young-Wook

2016-05-01

The breakaway swelling in U-Mo/Al dispersion fuel is known to be caused by large pore formation enhanced by interaction layer (IL) growth between fuel particles and Al matrix. In this study, a critical IL thickness was defined as a criterion for the formation of a large pore in U-Mo/Al dispersion fuel. Specifically, the critical IL thickness is given when two neighboring fuel particles come into contact with each other in the developed IL. The model was verified using the irradiation data from the RERTR tests and KOMO- 4 test. The model application to full-sized sample irradiations such as IRISs, FUTURE,more » E-FUTURE, and AFIP-1 tests resulted in conservative predictions. The parametric study revealed that the fuel particle size and the homogeneity of the fuel particle distribution are influential for fuel performance.« less

Distinct 238U/235U ratios and REE patterns in plutonic and volcanic angrites: Geochronologic implications and evidence for U isotope fractionation during magmatic processes

NASA Astrophysics Data System (ADS)

Tissot, François L. H.; Dauphas, Nicolas; Grove, Timothy L.

2017-09-01

Angrites are differentiated meteorites that formed between 4 and 11 Myr after Solar System formation, when several short-lived nuclides (e.g., 26Al-26Mg, 53Mn-53Cr, 182Hf-182W) were still alive. As such, angrites are prime anchors to tie the relative chronology inferred from these short-lived radionuclides to the absolute Pb-Pb clock. The discovery of variable U isotopic composition (at the sub-permil level) calls for a revision of Pb-Pb ages calculated using an ;assumed; constant 238U/235U ratio (i.e., Pb-Pb ages published before 2009-2010). In this paper, we report high-precision U isotope measurement for six angrite samples (NWA 4590, NWA 4801, NWA 6291, Angra dos Reis, D'Orbigny, and Sahara 99555) using multi-collector inductively coupled plasma mass-spectrometry and the IRMM-3636 U double-spike. The age corrections range from -0.17 to -1.20 Myr depending on the samples. After correction, concordance between the revised Pb-Pb and Hf-W and Mn-Cr ages of plutonic and quenched angrites is good, and the initial (53Mn/55Mn)0 ratio in the Early Solar System (ESS) is recalculated as being (7 ± 1) × 10-6 at the formation of the Solar System (the error bar incorporates uncertainty in the absolute age of Calcium, Aluminum-rich inclusions - CAIs). An uncertainty remains as to whether the Al-Mg and Pb-Pb systems agree in large part due to uncertainties in the Pb-Pb age of CAIs. A systematic difference is found in the U isotopic compositions of quenched and plutonic angrites of +0.17‰. A difference is also found between the rare earth element (REE) patterns of these two angrite subgroups. The δ238U values are consistent with fractionation during magmatic evolution of the angrite parent melt. Stable U isotope fractionation due to a change in the coordination environment of U during incorporation into pyroxene could be responsible for such a fractionation. In this context, Pb-Pb ages derived from pyroxenes fraction should be corrected using the U isotope composition

Heterogeneity in the 238U/235U Ratios of Angrites.

NASA Astrophysics Data System (ADS)

Tissot, F.; Dauphas, N.; Grove, T. L.

2016-12-01

Angrites are differentiated meteorites of basaltic composition, of either volcanic or plutonic origin, that display minimal post-crystallization alteration, metamorphism, shock or impact brecciation. Because quenched angrites cooled very rapidly, all radiochronometric systems closed simultaneously in these samples. Quenched angrites are thus often used as anchors for cross-calibrating short-lived dating methods (e.g., 26Al-26Mg) and the absolute dating techniques (e.g, Pb-Pb). Due to the constancy of the 238U/235U ratio in natural samples, Pb-Pb ages have long been calculated using a "consensus" 238U/235U ratio, but the discovery of resolvable variations in the 238U/235U ratio of natural samples, means that the U isotopic composition of the material to date also has to be determined in order to obtain high-precision Pb-Pb ages. We set out (a) to measure at high-precision the 238U/235U ratio of a large array of angrites to correct their Pb-Pb ages, and (b) to identify whether all angrites have a similar U isotopic composition, and, if not, what were the processes responsible for this variability. Recently, Brennecka & Wadhwa (2012) suggested that the angrite-parent body had a homogeneous 238U/235U ratio. They reached this conclusion partly because they propagated the uncertainties of the U isotopic composition of the various U double spikes that they used onto the final 238U/235U ratio the sample. Because this error is systematic (i.e., it affects all samples similarly), differences in the δ238U values of samples corrected by the same double spike are better known than one would be led to believe if uncertainties on the spike composition are propagated. At the conference, we will present the results of the high-precision U isotope analyses for six angrite samples: NWA 4590, NWA 4801, NWA 6291, Angra dos Reis, D'Orbigny, and Sahara 99555. We will show that there is some heterogeneity in the δ238U values of the angrites and will discuss the possible processes by

Al-Qaeda's operational evolution: behavioral and organizational perspectives.

PubMed

Borum, Randy; Gelles, Michael

2005-01-01

Al-Qaeda is widely regarded by the military, law enforcement, diplomatic, and intelligence communities as being the foremost threat to U.S. national security and safety. The nature of this threat, however, has changed since al-Qaeda first emerged in the late 1980s. This article describes the emergence of a new form of transnational terrorism and details al-Qaeda's progression from being an organization to an ideological movement. Drawing on a theory of social movements, we analyze its trajectory and the levels of influence. We also offer a behavioral perspective in explaining how al-Qaeda has adapted as a learning organization with new leadership, tactics, and patterns of recruitment and training.

Irradiated microstructure of U-10Mo monolithic fuel plate at very high fission density

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gan, J.; Miller, B. D.; Keiser, D. D.

Monolithic U-10Mo alloy fuel plates with Al-6061 cladding are being developed for use in research and test reactors as low enrichment fuel (< 20% U-235 enrichment) as a result of its high uranium loading capacity compared to that of U-7Mo dispersion fuel. These fuel plates contain a Zr diffusion barrier between the U-10Mo fuel and Al-6061 cladding that suppresses the interaction between the U-Mo fuel foil and Al alloy cladding that is known to be problematic under irradiation. This paper discusses the TEM results of the U-10Mo/Zr/Al6061 monolithic fuel plate (Plate ID: L1P09T, ~ 59% U-235 enrichment) irradiated in Advancedmore » Test Reactor at Idaho National Laboratory as part of RERTR-9B irradiation campaign with an unprecedented high local fission density of 9.8E+21 fissions/cm3. The calculated fuel foil centerline temperature at the beginning of life and the end of life is 141 and 194 C, respectively. A total of 5 TEM lamellas were prepared using focus ion beam lift-out technique. The estimated U-Mo fuel swelling, based on the fuel foil thickness change from SEM, is approximately 76%. Large bubbles (> 1 µm) are distributed evenly in U-Mo and interlink of these bubbles is evident. The average size of subdivided grains at this fission density appears similar to that at 5.2E+21 fissions/cm3. The measured average Mo and Zr content in the fuel matrix is ~ 30 at% and ~ 7 at%, respectively, in general agreement with the calculated Mo and Zr from fission density.« less

Swelling of U-7Mo/Al-Si dispersion fuel plates under irradiation - Non-destructive analysis of the AFIP-1 fuel plates

NASA Astrophysics Data System (ADS)

Wachs, D. M.; Robinson, A. B.; Rice, F. J.; Kraft, N. C.; Taylor, S. C.; Lillo, M.; Woolstenhulme, N.; Roth, G. A.

2016-08-01

Extensive fuel-matrix interactions leading to plate pillowing have proven to be a significant impediment to the development of a suitable high density low-enriched uranium molybdenum alloy (U-Mo) based dispersion fuel for high power applications in research reactors. The addition of silicon to the aluminum matrix was previously demonstrated to reduce interaction layer growth in mini-plate experiments. The AFIP-1 project involved the irradiation, in-canal examination, and post-irradiation examination of two fuel plates. The irradiation of two distinct full size, flat fuel plates (one using an Al-2wt%Si matrix and the other an Al-4043 (∼4.8 wt% Si) matrix) was performed in the INL ATR reactor in 2008-2009. The irradiation conditions were: ∼250 W/cm2 peak Beginning Of Life (BOL) power, with a ∼3.5e21 f/cm3 peak burnup. The plates were successfully irradiated and did not show any pillowing at the end of the irradiation. This paper reports the results and interpretation of the in-canal and post-irradiation non-destructive examinations that were performed on these fuel plates. It further compares additional PIE results obtained on fuel plates irradiated in contemporary campaigns in order to allow a complete comparison with all results obtained under similar conditions. Except for a brief indication of accelerated swelling early in the irradiation of the Al-2Si plate, the fuel swelling is shown to evolve linearly with the fission density through the maximum burnup.

Joule heat production rate and the particle energy injection rate as a function of the geomagnetic indices AE and AL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahn, B.; Akasofu, S.; Kamide, Y.

1983-08-01

As a part of the joint efforts of operating six meridian chains of magnetometers during the IMS, magnetic records from 71 stations are used to deduce the distribution of electric fields and currents in the polar ionosphere for March 17, 18, and 19, 1978. As a continuation of this project, we have constructed hourly distribution maps of the Joule heat production rate and their sum over the entire polar region on the three days. For this purpose the conductivity distribution is inferred at each instant partially on the basis of an empirical method devised by Ahn et al. (1982). Themore » particle energy injection rate is estimated similarly by using an empirical method. The data set thus obtained allows us to estimate also the global Joule heat production rate U/sub J/, the global particle energy injection rate U/sub A/ and the sum U/sub Gamma/ of the two quantities. It is found that three global quantities (watt) are related almost linearly to the AE(nT) and AL(nT) indices. Our present estimates give the following relationships: U/sub J/ = 2.3 times 10/sup 8/ x AE/sub 8/ U/sub A/ = 0.6 times 10/sup 8/ x AE/sub 8/ and U/sub I/ = 2.9 times 10/sup 8/ x AE: U/sub J/ = 3.0 times 10/sup 8/ x AL/sub 8/ U/sub A/ = 0.8 times 10/sup 8/ x AL, and U/sub I/ = 3.8 times 10/sup 8/ x AL.« less

77 FR 8942 - Alabama Disaster Number AL-00040

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-15

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13002 and 13003] Alabama Disaster Number AL-00040 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of the Presidential declaration of a major [[Page 8943

The ortho:para-H_2 ratio in C- and J-type shocks

NASA Astrophysics Data System (ADS)

Wilgenbus, D.; Cabrit, S.; Pineau des Forêts, G.; Flower, D. R.

2000-04-01

We have computed extensive grids of models of both C- and J-type planar shock waves, propagating in dark, cold molecular clouds, in order to study systematically the behaviour of the ortho:para-H_2 ratio. Careful attention was paid to both macroscopic (dynamical) and microscopic (chemical reactions and collisional population transfer in H_2) aspects. We relate the predictions of the models to observational determinations of the ortho:para-H_2 ratio using both pure rotational lines and rovibrational lines. As an illustration, we consider ISO and ground-based H_2 observations of HH 54. Neither planar C-type nor planar J-type shocks appear able to account fully for these observations. Given the additional constraints provided by the observed ortho:para H_2 ratios, a C-type bowshock, or a C-type precursor followed by a J-type shock, remain as plausible models. Tables~2a-f and 4a-f are only available in electronic form at the CDS via anonymous ftp to cdsarc.u-strasbg.fr (130.79.128.5) or via http://cdsweb.u-strasbg.fr/Abstract.html

78 FR 22361 - Alabama Disaster #AL-00049

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-15

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13530 and 13531] Alabama Disaster AL-00049 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of Alabama dated 04/04/2013. Incident: Severe Storms...

78 FR 26100 - Alabama Disaster #AL-00050

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-03

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13547 and 13548] Alabama Disaster AL-00050 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of Alabama dated 04/23/2013. Incident: Severe Storms...

78 FR 4967 - Alabama Disaster #AL-00046

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-23

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13443 and 13444] Alabama Disaster AL-00046 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of ALABAMA dated 01/10/2013. Incident: Severe Storms and...

A Contribution to the Kinetic Study of the Metatectic Reaction U+U$sub 3$Si$sub 2$$Yields$U$sub 3$Si; CONTRIBUTION AL ESTUDIO CINETICO DE LA REACCION METATECTICA U+U$sub 3$Si$sub 2$$Yields$U$sub 3$Si

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruiperez, J.A.; Hernandez, J.A.E.

1962-01-01

An experimental study was made to decide upon the advantages and drawbacks of the different methods and reagents employed in the metallography of U-Si alloys. It has been observed that all samples thermally treated to the epsilon-phase undergo a coalescence of the U/sub 3/Si/sub 2/ particles. The coalescence decreases the surface available for reaction and consequently the reaction rate. The growth of the U/sub 3/Si/sub 2/ phase particles was determined as a function of time and temperature. To obtain samples with nuclei sufficiently isolated so that the U/sub 3/Si rings will not interfere their respective growth, the conditions that regulatemore » coalescence, Si content and thermal treatment, were determined. Data rel1tive to the growth of the U/sub 3/ Si phase-rings were obtained. Curves relating growth, time, and temperature are presented. The parameters that define the diffusion regulated reaction can be deduced from these curves. (auth)« less

Irradiated microstructure of U-10Mo monolithic fuel plate at very high fission density

NASA Astrophysics Data System (ADS)

Gan, J.; Miller, B. D.; Keiser, D. D.; Jue, J. F.; Madden, J. W.; Robinson, A. B.; Ozaltun, H.; Moore, G.; Meyer, M. K.

2017-08-01

Monolithic U-10Mo alloy fuel plates with Al-6061 cladding are being developed for use in research and test reactors as low enrichment fuel (<20% U-235 enrichment) as a result of its high uranium loading capacity compared to that of U-7Mo dispersion fuel. These fuel plates contain a Zr diffusion barrier between the U-10Mo fuel and Al-6061 cladding that suppresses the interaction between the U-Mo fuel foil and Al alloy cladding that is known to be problematic under irradiation. Different methods have been employed to fabricate monolithic fuel plates, including hot-rolling with no cold-rolling. L1P09T is a hot-rolled fuel plate irradiated to high fission density in the RERTR-9B experiment. This paper discusses the TEM characterization results for this U-10Mo/Zr/Al6061 monolithic fuel plate (∼59% U-235 enrichment) irradiated in Advanced Test Reactor at Idaho National Laboratory with an unprecedented high local fission density of 9.8E+21 fissions/cm3. The calculated fuel foil centerline temperature at the beginning of life and the end of life is 141 and 194 °C, respectively. TEM lamellas were prepared using focus ion beam lift-out technique. The estimated U-Mo fuel swelling, based on the fuel foil thickness change from SEM, is approximately 76%. Large bubbles (>1 μm) are distributed evenly in U-Mo and interlink of these bubbles is evident. The average size of subdivided grains at this fission density appears similar to that at 5.2E+21 fissions/cm3. The measured average Mo and Zr content in the fuel matrix is ∼30 at% and ∼7 at%, respectively, in general agreement with the calculated Mo and Zr from fission density.

Association of proteomics changes with Al-sensitive root zones in switchgrass

USDA-ARS?s Scientific Manuscript database

In this paper, we report on aluminum (Al)-induced root proteomic changes in switchgrass. After growth in a hydroponic culture system supplemented with 400 uM of Al, plants began to show signs of physiological stress such as a reduction in photosynthetic rate. At this time, the basal 2-cmlong root ti...

75 FR 26814 - Alabama Disaster #AL-00031

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-12

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12157 and 12158] Alabama Disaster AL-00031 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama (FEMA- 1908-DR), dated 05...

76 FR 27141 - Alabama Disaster # AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28/2011. Incident: Severe...

75 FR 474 - Alabama Disaster #AL-00026

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-05

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 11988 and 11989] Alabama Disaster AL-00026 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama (FEMA- 1866-DR), dated 12...

77 FR 60003 - Alabama Disaster #AL-00044

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13317 and 13318] Alabama Disaster AL-00044 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama (FEMA- 4082-DR), dated 09...

77 FR 7227 - Alabama Disaster #AL-00040

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13002 and 13003] Alabama Disaster AL-00040 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for the State of Alabama (FEMA-4052-DR), dated 02/01/2012. Incident: Severe...

The nuclear quadrupole coupling constants and the structure of the para-para ammonia dimer

NASA Astrophysics Data System (ADS)

Heineking, N.; Stahl, W.; Olthof, E. H. T.; Wormer, P. E. S.; van der Avoird, A.; Havenith, M.

1995-06-01

Expressions are derived for the nuclear quadrupole splittings in the E3 and E4 (para-para) states of (NH3)2 and it is shown that these can be matched with the standard expressions for rigid rotors with two identical quadrupolar nuclei. The matching is exact only when the off-diagonal Coriolis coupling is neglected. However, the selection rules for rotational transitions are just opposite to those for the rigid rotor. Hyperfine splittings are measured for the J=2←1 transitions in the E3 and E4 states with ‖K‖=1; the quadrupole coupling constants χaa=0.1509(83) MHz and χbb-χcc=2.8365(83) MHz are extracted from these measurements by the use of the above mentioned correspondence with the rigid rotor expressions. The corresponding results are also calculated, with and without the Coriolis coupling, from the six-dimensional vibration-rotation-tunneling (VRT) wave functions of (NH3)2, which were previously obtained by Olthof et al. [E.H.T. Olthof, A. van der Avoird, and P.E.S. Wormer, J. Chem. Phys. 101, 8430 (1994)]. From the comparison of χaa with the measured value it follows that the semiempirical potential and the resulting VRT states of Olthof et al. are very accurate along the interchange (ϑA,ϑB) coordinate. From χbb-χcc it follows that this potential is probably too soft in the dihedral angle γ¯=γA-γB, which causes the torsional amplitude to be larger than derived from the experiment.

Detailed measurements of local thickness changes for U-7Mo dispersion fuel plates with Al-3.5Si matrix after irradiation at different powers in the RERTR-9B experiment

NASA Astrophysics Data System (ADS)

Keiser, Dennis D.; Williams, Walter; Robinson, Adam; Wachs, Dan; Moore, Glenn; Crawford, Doug

2017-10-01

The Materials Management and Minimization program is developing fuel designs to replace highly enriched fuel with fuels of low enrichment. Swelling is an important irradiation behavior that needs to be well understood. Data from high resolution thickness measurements performed on U-7Mo dispersion fuel plates with Al-Si alloy matrices that were irradiated at high power is sparse. This paper reports the results of detailed thickness measurements performed on two dispersion fuel plates that were irradiated at relatively high power to high fission densities in the Advanced Test Reactor in the same RERTR-9B experiment. Both plates were irradiated to similar fission densities, but one was irradiated at a higher power than the other. The goal of this work is to identify any differences in the swelling behavior when fuel plates are irradiated at different powers to the same fission densities. Based on the results of detailed thickness measurments, more swelling occurs when a U-7Mo dispersion fuel with Al-3.5Si matrix is irradiated to a high fission density at high power compared to one irradiated at a lower power to high fission density.

Strategic Dissonance RPA Tactics To Defeat Al Qaeda

DTIC Science & Technology

2015-11-24

Pakistan NDU Journal XXVIII (2014): 77- 86. http://www.ndu.edu.pk/issra/issra_pub/2014/NDU-Journal-2014.pdf. Maass, Matthias. “From U - 2s to Drones: U.S...accordance with Air Force Instruction 51-303, it is not copyrighted, but is the property of the United States government. iii Biography Mr... aircraft (RPA) as the primary means to defeat al-Qaeda is failing. The tactic is a convenient weapon of choice because it is accurate, low risk, and

Petrography, mineralogy, and geochemistry of lunar meteorite Sayh al Uhaymir 300

NASA Astrophysics Data System (ADS)

Hsu, Weibiao; Zhang, Aicheng; Bartoschewitz, Rainer; Guan, Yunbin; Ushikubo, Takayuki; KrńHenbÜHl, Urs; Niedergesaess, Rainer; Pepelnik, Rudolf; Reus, Ulrich; Kurtz, Thomas; Kurtz, Paul

2008-08-01

We report here the petrography, mineralogy, and geochemistry of lunar meteorite Sayh al Uhaymir 300 (SaU 300). SaU 300 is dominated by a fine-grained crystalline matrix surrounding mineral fragments (plagioclase, pyroxene, olivine, and ilmenite) and lithic clasts (mainly feldspathic to noritic). Mare basalt and KREEPy rocks are absent. Glass melt veins and impact melts are present, indicating that the rock has been subjected to a second impact event. FeNi metal and troilite grains were observed in the matrix. Major element concentrations of SaU 300 (Al2O3 21.6 wt% and FeO 8.16 wt%) are very similar to those of two basalt-bearing feldspathic regolith breccias: Calcalong Creek and Yamato (Y-) 983885. However, the rare earth element (REE) abundances and pattern of SaU 300 resemble the patterns of feldspathic highlands meteorites (e.g., Queen Alexandra Range (QUE) 93069 and Dar al Gani (DaG) 400), and the average lunar highlands crust. It has a relatively LREE-enriched (7 to 10 x CI) pattern with a positive Eu anomaly (˜11 x CI). Values of Fe/Mn ratios of olivine, pyroxene, and the bulk sample are essentially consistent with a lunar origin. SaU 300 also contains high siderophile abundances with a chondritic Ni/Ir ratio. SaU 300 has experienced moderate terrestrial weathering as its bulk Sr concentration is elevated compared to other lunar meteorites and Apollo and Luna samples. Mineral chemistry and trace element abundances of SaU 300 fall within the ranges of lunar feldspathic meteorites and FAN rocks. SaU 300 is a feldspathic impact-melt breccia predominantly composed of feldspathic highlands rocks with a small amount of mafic component. With a bulk Mg# of 0.67, it is the most mafic of the feldspathic meteorites and represents a lunar surface composition distinct from any other known lunar meteorites. On the basis of its low Th concentration (0.46 ppm) and its lack of KREEPy and mare basaltic components, the source region of SaU 300 could have been within a highland

Elastic-Plastic Behavior of U6Nb Under Ramp Wave Loading

NASA Astrophysics Data System (ADS)

Hayes, D. B.; Hall, C.; Hixson, R. S.

2005-07-01

Prior shock experiments on the alloy uranium-niobium-6 wt.% (U6Nb) were absent an elastic precursor when one was expected (A. K. Zurek, et. al., <u>Journal de Physique IV, u>10 (#9) p677-682). This was later explained as a consequence of shear stress relaxation from time-dependent twinning that prevented sufficient shear stress for plastic yielding. (D. B. Hayes, et. al., <u>Shock Compression of Condensed Matter-2003, p1177, American Institute of Physics 2004) Pressure was ramped to 13 GPa in 150-ns on eight U6Nb specimens with thicknesses from 0.5 -- 1.1-mm and the back surface velocities were measured with laser interferometry. This pressure load produces a stress wave with sufficiently fast rise time so that, according to the prior work, twins do not have time to form. Four of the U6Nb specimens had been cold-rolled which increased the yield stress. Each velocity history was analyzed with a backward integration analysis to give the stress-strain response of the U6Nb. Comparison of these results with prior Hugoniot measurements shows that the U6Nb in the present experiments responds as an elastic-plastic material and the deduced yield strength of the baseline and of the cold-rolled material agree with static results.u>

Accidentes laborales asociados al desánimo de médicos SERUMS para laborar en el primer nivel de atención de Lima, Perú

PubMed Central

Mejia, Christian R.; Valladares-Garrido, Mario J.; Romero, Brian M.; Valladares-Garrido, Danai; Linares-Reyes, Edgardo

2018-01-01

Introducción la retención laboral es un tema de suma importancia, porque se requiere de profesionales en el primer nivel de atención (PNA). El objetivo fue determinar si los accidentes laborales se asociaron al desánimo de los médicos para trabajar en el PNA de Lima, Perú. Métodos estudio transversal analítico de datos secundarios de una base de datos generada de una encuesta a médicos que realizaron su Servicio Rural y Urbano-Marginal en Salud (SERUMS). Se incluyó solo a los médicos que manifestaron al inicio del SERUMS que podían trabajar en el PNA de Lima. Se definió como cambio de intención de trabajo en el PNA a los que finalizando el SERUMS refirieron que ya no deseaban laborar en Lima. Esto se asoció según si tuvieron un accidente laboral y se ajustó por otras variables. Resultados de los 124 médicos el 63% fueron hombres (78). La mediana de edad fue de 26 años (rango intercuartílico: 25-27 años). Después de su SERUMS, el 12% (15) manifestó que cambió su interés y que deseaba trabajar en la capital. En el análisis multivariado, haber tenido un accidente laboral disminuyó la frecuencia del cambio de intención de trabajo en el PNA (RPa: 0.28, IC 95%: 0.14-0.54, p < 0,001), ajustado por ocho variables. Conclusiones en un estudio previo los accidentes laborales disminuyeron la frecuencia de trabajar en provincias, pero nuestro estudio dice lo contrario, posiblemente por la percepción de que un trabajo en la capital del país permite estar más cerca de los servicios para ser atendido en caso de cualquier emergencia. PMID:29190859

Afghanistan: Post-Taliban Governance, Security, and U.S. Policy

DTIC Science & Technology

2010-06-07

but later joined Rabbani’s 5 A pharmaceutical plant in Sudan (Al Shifa) believe to be...producing chemical weapons for Al Qaeda also was struck that day, although U.S. reviews later corroborated Sudan’s assertions that the plant was...commercially profitable for China Metallurgical Group, includes construction of two coal-fired electric power plant (one of which will supply more electricity

Afghanistan: Post-Taliban Governance, Security, and U.S. Policy

DTIC Science & Technology

2010-08-17

Rabbani’s 5 A pharmaceutical plant in Sudan (Al Shifa) believe to be producing chemical...weapons for Al Qaeda also was struck that day, although U.S. reviews later corroborated Sudan’s assertions that the plant was strictly civilian in...China Metallurgical Group, includes construction of two coal-fired electric power plant (one of which will supply more electricity to Kabul city); a

Upwelling Rates Beneath Hotspots : Evidence From U-Series in Basalts From the Mid-Atlantic Ridge and the Azores Islands

NASA Astrophysics Data System (ADS)

Bourdon, B. P.; Turner, S. P.

2001-12-01

In this study, we have analyzed U-series in lavas from the Azores islands and the nearby Mid-Atlantic Ridge (FAZAR cruise) in an attempt to assess the relative importance of melting processes versus source variations in the context of ridge-hotpsot interaction. The lavas were analyzed for 238U-230Th (Turner et al. 1997, Bourdon et al. 1996) 226Ra-230Th and 235U-231Pa disequilibria by thermal ionisation mass spectrometry. Our results for the historic lavas from the Azores islands show that the 231Pa excess are at the low end of the trend found for other OIB (Pickett et al. 1997 and Bourdon et al. 1998) and fall on a positive correlation in a 231Pa/235U versus 230Th/238U diagram. In contrast, lavas from the nearby Mid-Atlantic ridge are characterized by larger (231Pa/235U) activity ratios for similar and greater (230Th/238U) ratios. There is also a weak correlation between 226Ra/230Th and 231Pa/235U. These data do not indicate a simple mixing trend between an N-MORB and an enriched component in the 231Pa/235U versus 230Th/238U diagram since the MORBs which do not have the most radiogenic isotope signatures compared with the Azores island basalts have some of the largest (230Th/238U) and 231Pa/235U. Clearly, the dynamics of melting must have played a role in generating larger 230Th and 231Pa excesses beneath the Mid-Atlantic ridge. We infer that this must be due to the absence of a lithospheric lid as larger excesses of 230Th and 231Pa can be generated for longer melting columns. Thus, ridge-hotspot interaction cannot imply a simple transfer of melt from the hotspot to the ridge. The 230Th/238U and 226Ra/230Th data across the Azores plateau shows a maximum for the island of Terceira and mimics the depth anomaly which is thought to result from the hotspot. This trend is also consistent with observations of rare gases (M. Moreira pers. comm.) and suggests that it must be related to the presence of deep material. The U-series trend is the reverse of the trend found in

The Future of U.S. Landpower: Special Operations Versatility, Marine Corps Utility

DTIC Science & Technology

2013-01-01

forces-to-face- al-shabaab-lra-.html>. 72 Flynn. 73 Owens. 74 Sustaining U.S. Global Leadership, 3. 75 Jackie Calmes, “Obama and Gillard Expand U.S.-Australia Military Ties,” The New York Times, November 16, 2011.

Neutron Productions from thin Be target irradiated by 50 MeV/u 238U beam

NASA Astrophysics Data System (ADS)

Lee, Hee-Seock; Oh, Joo-Hee; Jung, Nam-Suk; Oranj, Leila Mokhtari; Nakao, Noriaki; Uwamino, Yoshitomo

2017-09-01

Neutrons generated from thin beryllium target by 50 MeV/u 238U beam were measured using activation analysis at 15, 30, 45, and 90 degrees from the beam direction. A 0.085 mm-thick Be stripper of RIBF was used as the neutron generating target. Activation detectors of bismuth, cobalt, and aluminum were placed out of the stripper chamber. The threshold reactions of 209Bi(n, xn)210-xBi(x=4 8), 59Co(n, xn)60-xCO(x=2 5), 59Co(n, 2nα)54Mn, 27Al(n, α)24Na, and 27Al(n,2nα)22Na were applied to measure the production rates of radionuclides. The neutron spectra were obtained using an unfolding method with the SAND-II code. All of production rates and neutron spectra were compared with the calculated results using Monte Carlo codes, the PHITS and the FLUKA. The FLUKA results showed better agreement with the measurements than the PHITS. The discrepancy between the measurements and the calculations were discussed.

Kinetics of Static Strain Aging in Polycrystalline NiAl-based Alloys

NASA Technical Reports Server (NTRS)

Weaver, M. L.; Kaufman, M. J.; Noebe, R. D.

1996-01-01

The kinetics of yield point return have been studied in two NiAl-based alloys as a function of aging time at temperatures between 300 and 700 K. The results indicate that the upper yield stress increment, Delta sigma(sub u) (i.e., stress difference between the upper yield point and the final flow stress achieved during prestraining), in conventional purity (CP-NiAl) and in high purity carbon-doped (NiAl-C) material first increased with a t(exp 2/3) relationship before reaching a plateau. This behavior suggests that a Cottrell locking mechanism is the cause for yield points in NiAl. In addition, positive y-axis intercepts were observed in plots of Delta sigma(sub u) versus t(exp 2/3) suggesting the operation of a Snoek mechanism. Analysis according to the Cottrell Bilby model of atmosphere formation around dislocations yields an activation energy for yield point return in the range 70 to 76 kJ/mol which is comparable to the activation energy for diffusion of interstitial impurities in bcc metals. It is, thus, concluded that the kinetics of static strain aging in NiAl are controlled by the locking of dislocations by Cottrell atmospheres of carbon atoms around dislocations.

76 FR 30225 - Alabama Disaster Number AL-00037

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-24

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12584 and 12585] Alabama Disaster Number AL-00037 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama...

77 FR 63410 - Alabama Disaster Number AL-00044

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-16

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13317 and 13318] Alabama Disaster Number AL-00044 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama...

76 FR 31388 - Alabama Disaster Number AL-00037

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-31

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12584 and 12585] Alabama Disaster Number AL-00037 AGENCY: U.S. Small Business Administration. ACTION: Amendment 2. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama...

76 FR 33805 - Alabama Disaster Number AL-00037

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-09

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12584 and 12585] Alabama Disaster Number AL-00037 AGENCY: U.S. Small Business Administration. ACTION: Amendment 3. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama...

76 FR 38264 - Alabama Disaster Number AL-00037

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-29

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12584 and 12585] Alabama Disaster Number AL-00037 AGENCY: U.S. Small Business Administration. ACTION: Amendment 5. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama...

76 FR 34121 - Alabama Disaster Number AL-00037

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12584 and 12585] Alabama Disaster Number AL-00037 AGENCY: U.S. Small Business Administration. ACTION: Amendment 4. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for Public Assistance Only for the State of Alabama...

Independent Assessment of U.S. Government Efforts against Al-Qaeda

DTIC Science & Technology

2017-10-01

as a result of its having joined the U.S.-led coalition in Iraq. Shortly after the bombings , Spain held elections, which resulted in the election of...not, on its own, have the capability to produce the laptop bomb that detonated aboard a flight out of Mogadishu in February 2016 and that therefore it...homelands and against Western partner nations. The 9/11 attacks followed the 2000 USS Cole bombing , the 2000 attempted bombing of the USS The

Molecular adsorption at electrolyte/α-Al2O3 interface of aluminum electrolytic capacitor revealed by sum frequency vibrational spectroscopy.

PubMed

Jia, Ming; Hu, Xiaoyu; Liu, Jin; Liu, Yexiang; Ai, Liang

2017-05-21

The operating voltage of an aluminum electrolytic capacitor is determined by the breakdown voltage (U b ) of the Al 2 O 3 anode. U b is related to the molecular adsorption at the Al 2 O 3 /electrolyte interface. Therefore, we have employed sum-frequency vibrational spectroscopy (SFVS) to study the adsorption states of a simple electrolyte, ethylene glycol (EG) solution with ammonium adipate, on an α-Al 2 O 3 surface. In an acidic electrolyte (pH < 6), the Al 2 O 3 surface is positively charged. The observed SFVS spectra show that long chain molecules poly ethylene glycol and ethylene glycol adipate adopt a "lying" orientation at the interface. In an alkaline electrolyte (pH > 8), the Al 2 O 3 surface is negatively charged and the short chain EG molecules adopt a "tilting" orientation. The U b results exhibit a much higher value at pH < 6 compared with that at pH > 8. Since the "lying" long chain molecules cover and protect the Al 2 O 3 surface, U b increases with a decrease of pH. These findings provide new insights to study the breakdown mechanisms and to develop new electrolytes for high operating voltage capacitors.

Melhoramentos no código Wilson-Devinney para binárias eclipsantes

NASA Astrophysics Data System (ADS)

Vieira, L. A.; Vaz, L. P. R.

2003-08-01

A análise de curvas de luz e velocidades radiais de sistemas binários eclipsantes pode ser feita por meio de vários modelos. Um desses é o Modelo Wilson-Devinney (WD). Ao longo dos anos, esse modelo sofreu várias alterações em seus códigos principais, com a finalidade de torná-lo mais consistente tanto fíisica como numericamente. O Modelo WD tem sido melhorado de várias maneiras em seus dois códigos: um para a predição das curvas de luz teórica e de velocidade radiais e outra para as soluções destas curvas. Teoricamente, na física do modelo, nós introduzimos a possibilidade de levar em conta os efeitos do movimento apsidal. Numericamente, nós introduzimos a possibilidade de usar o Método SIMPLEX no procedimento da solução, como uma alternativa para o já implementado Método de Mínimos Quadrados (Least Squares Method). Estas modificações, juntamente com outras já introduzidas pelo nosso grupo anteriormente, tornam o código mais eficiente na solução das curvas de luz e de velocidade radiais de binárias eclipsantes. Como o modelo tem sido usado para analisar sistemas com componentes pré-sequência principal (TY CrA, Casey et al. 1998, Vaz et al. 1998), SM 790, Stassun et al. 2003), este melhoramento beneficiará estes casos também. Apresentamos os resultados obtidos com a modificação do código WD por meio do uso de dados da estrela GL Carinae, comprovando, (1) que os parâmetros orbitais calculados por nós são coerentes com os obtidos anteriormente na literatura (Giménez & Clausen, 1986) e com os obtidos por Faria (1987), e (2) que a implementação do Método SIMPLEX torna o código mais lento mas completamente consistente internamente e evita os problemas gerados pelo uso do Método de Mínimos Quadrados, tais como imprecisão no cálculo das derivadas parciais e convergência para mínimos locais.

Electron impact ionization dynamics of para-benzoquinone

NASA Astrophysics Data System (ADS)

Jones, D. B.; Ali, E.; Ning, C. G.; Colgan, J.; Ingólfsson, O.; Madison, D. H.; Brunger, M. J.

2016-10-01

Triple differential cross sections (TDCSs) for the electron impact ionization of the unresolved combination of the 4 highest occupied molecular orbitals (4b3g, 5b2u, 1b1g, and 2b3u) of para-benzoquinone are reported. These were obtained in an asymmetric coplanar geometry with the scattered electron being observed at the angles -7.5°, -10.0°, -12.5° and -15.0°. The experimental cross sections are compared to theoretical calculations performed at the molecular 3-body distorted wave level, with a marginal level of agreement between them being found. The character of the ionized orbitals, through calculated momentum profiles, provides some qualitative interpretation for the measured angular distributions of the TDCS.

Simmonsite, Na2LiAlF6, a new mineral from the Zapot amazonite-topazzinnwaldite pegmatite, Hawthorne, Nevada, U.S.A

USGS Publications Warehouse

Foord, E.E.; O'Connor, J. T.; Hughes, J.M.; Sutley, S.J.; Falster, A.U.; Soregaroli, A.E.; Lichte, F.E.; Kile, D.E.

1999-01-01

Simmonsite, Na2LiAlF6, a new mineral of pegmatitic-hydrothermal origin, occurs in a late-stage breccia pipe structure that cuts the Zapot amazonite-topaz-zinnvvaldite pegmatite located in the Gillis Range, Mineral Co., Nevada, U.S.A. The mineral is intimately intergrown with cryolite, cryolithionite and trace elpasolite. A secondary assemblage of other alumino-fluoride minerals and a second generation of cryolithionite has formed from the primary assemblage. The mineral is monoclinic, P21 or P21/m, a = 7.5006(6) A??, b = 7.474(1) A??, c = 7.503(1) A??, ??= 90.847(9) ??, V=420.6(1) A??3, Z = 4. The four strongest diffraction maxima [d(A??), likl, I/I100] are (4.33, 111 and 111, 100); (1.877, 400 and 004, 90); (2.25, 13T, 113, 131 and 311, 70); and (2.65, 220, 202, 022, 60). Simmonsite is pale buff cream with white streak, somewhat greasy, translucent to transparent, Mohs hardness of 2.5-3, no distinct cleavage, subconchoidal fracture, no parting, not extremely brittle, Dm is 3.05(2) g/cm3, and Dc is 3.06(1) g/cm3. The mineral is biaxial, very nearly Isotropie, N is 1.359(1) for ?? = 589 nm, and birefringence is 0.0009. Electron microprobe analyses gave (wt%) Na = 23.4, Al = 13.9, F = 58.6, Li = 3.56 (calculated), with a total of 99.46. The empirical formula (based on 6 F atoms) is Na1.98Li1.00 ooAl|ooF6. The crystal structure was not solved, presumably because of unit-cell scale twinning, but similarities to the perovskite-type structure exist. The mineral is named for William B. Simmons, Professor of Mineralogy and Petrology, University of New Orleans, New Orleans.

Thermodynamic modelling of the C-U and B-U binary systems

NASA Astrophysics Data System (ADS)

Chevalier, P. Y.; Fischer, E.

2001-02-01

The thermodynamic modelling of the carbon-uranium (C-U) and boron-uranium (B-U) binary systems is being performed in the framework of the development of a thermodynamic database for nuclear materials, for increasing the basic knowledge of key phenomena which may occur in the event of a severe accident in a nuclear power plant. Applications are foreseen in the nuclear safety field to the physico-chemical interaction modelling, on the one hand the in-vessel core degradation producing the corium (fuel, zircaloy, steel, control rods) and on the other hand the ex-vessel molten corium-concrete interaction (MCCI). The key O-U-Zr ternary system, previously modelled, allows us to describe the first interaction of the fuel with zircaloy cladding. Then, the three binary systems Fe-U, Cr-U and Ni-U were modelled as a preliminary work for modelling the O-U-Zr-Fe-Cr-Ni multicomponent system, allowing us to introduce the steel components in the corium. In the existing database (TDBCR, thermodynamic data base for corium), Ag and In were introduced for modelling AIC (silver-indium-cadmium) control rods which are used in French pressurized water reactors (PWR). Elsewhere, B 4C is also used for control rods. That is why it was agreed to extend in the next years the database with two new components, B and C. Such a work needs the thermodynamic modelling of all the binary and pseudo-binary sub-systems resulting from the combination of B, B 2O 3 and C with the major components of TDBCR, O-U-Zr-Fe-Cr-Ni-Ag-In-Ba-La-Ru-Sr-Al-Ca-Mg-Si + Ar-H. The critical assessment of the very numerous experimental information available for the C-U and B-U binary systems was performed by using a classical optimization procedure and the Scientific Group Thermodata Europe (SGTE). New optimized Gibbs energy parameters are given, and comparisons between calculated and experimental equilibrium phase diagrams or thermodynamic properties are presented. The self-consistency obtained is quite satisfactory.

Controlling Self-Assembly in Al(110) Homoepitaxy

NASA Astrophysics Data System (ADS)

Tiwary, Yogesh; Fichthorn, Kristen

2010-03-01

Homoepitaxial growth on Al(110) exhibits nanoscale self-assembly into huts with well-defined (100) and (111) facets [1]. Although some of the diffusion mechanisms underlying this kinetic self-assembly were identified and incorporated into a two-dimensional model [2], we used density-functional theory (DFT) to identify many other mechanisms that are needed to describe the three-dimensional assembly seen experimentally [3]. We developed a three-dimensional kinetic Monte Carlo (KMC) model of Al(110) homoepitaxy. The inputs to the model were obtained from DFT [3,4]. Our model is in agreement with experimentally observed trends for this system. We used KMC to predict self-assembly under various growth conditions. To achieve precise placement of Al nanohuts, we simulated thermal-field-directed assembly [5]. Our results indicate that this technique can be used to create uniform arrays of nanostructures. [1] F. Buatier de Mongeot, W. Zhu, A. Molle, R. Buzio, C. Boragno, U. Valbusa, E. Wang, and Z. Zhang, Phys. Rev. Lett. 91, 016102 (2003). [2] W. Zhu, F. Buatier de Mongeot, U. Valbusa, E. G. Wang, and Z. Y. Zhang, Phys. Rev. Lett. 92, 106102 (2004). [3] Y. Tiwary and K. A. Fichthorn, submitted to Phys. Rev. B. [4] Y. Tiwary and K. A. Fichthorn, Phys. Rev. B 78, 205418 (2008). [5] C. Zhang and R. Kalyanaraman, Appl. Phys. Lett. 83, 4827 (2003).

76 FR 27140 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 3. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

76 FR 34121 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 7. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

76 FR 27741 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-12

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 4. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

76 FR 27140 - ALABAMA Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] ALABAMA Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

76 FR 27139 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: A mendment 2. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

76 FR 28842 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-18

... SMALL BUSINESS ADMINISTRATION Disaster Declaration 12545 and 12546 Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 6. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

75 FR 27846 - Alabama Disaster Number AL-00029

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12155 and 12156] Alabama Disaster Number AL-00029 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1908-DR), dated 05/03...

76 FR 39149 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-05

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 9. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

76 FR 33805 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-09

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 8. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State ofAlabama (FEMA-1971-DR), dated 04/28...

76 FR 27740 - Alabama Disaster Number AL-00036

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-12

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12545 and 12546] Alabama Disaster Number AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Amendment 5. SUMMARY: This is an amendment of the Presidential declaration of a major disaster for the State of Alabama (FEMA-1971-DR), dated 04/28...

The North African Franchise: AQIM’s Threat to U.S. Security. Strategic Insights, Volume 8, Issue 5

DTIC Science & Technology

2009-12-01

The North African Franchise : AQIM’s Threat to U.S. Security Strategic Insights, Volume VIII, Issue 5 (December 2009) By Captain Russell J. Isaacs...the U.S. Government. Abstract Al Qaeda of the Islamic Maghreb (AQIM) is a growing and evolving North African franchise of Al Qaeda. While the group...in towns east of Algiers. Although this attack officially marked the emergence of Al Qaeda of the Islamic Maghreb (AQIM), a North African franchise

Shift Focus on the Al Qaeda Network: A More Comprehensive Approach to Defeating Al Qaeda

DTIC Science & Technology

2012-06-15

Declaration of jihad against the United States,” Al-Islah ( Internet ), September 2, 1996. As analyzed in Michael Scheuer, Osama bin Laden (New York...He enhanced his charismatic persona by deliberately modeling his life after that of Mohammed, the Islamic prophet.25 The irony of bin Laden is that...with the sensitive topic of a political ideology linked with a religion whose population is overwhelmingly distrustful of the U.S. Much has been made

The U.S., Japan, and Asia: Challenges to U.S. Policy

DTIC Science & Technology

1993-10-01

1945-1990. Cambridge: Cambridge UP, 1992. (E 183.8 .J3 B78 1992) Burks , Ardath W. Japan: A Postindustrial Power. 3rd ed. Boulder: Westview, 1991. (DS 806...1988) Anchordoguy, Marie . Computers Inc.: Japan’s Challenge to IB4. Cambridge: Harvard UP, 1989. (HD 9696 .C63 J29 1989) Arrison, Thomas S., et. al...Strategv towards the East. London: International Institute for Strategic Studies, 1984. (U 162 .A23 no.192) Burke , Patrick, ed. Nuclear Weapons World

Precise 238U(n,2n)237U reaction cross-section measurements using the activation facility at TUNL

NASA Astrophysics Data System (ADS)

Krishichayan, Fnu; Bhike, M.; Tornow, W.

2014-09-01

Accurate neutron-induced 238U(n,2n)237U reaction data are required for many practical applications, especially in the field of nuclear energy, including advanced heavy water reactors, where 238U is used as the breeding material to regenerate the fissile material 239Pu. Precise (n,2n) cross-section measurements of 238U are underway at TUNL with mono-energetic neutrons in the 8.0 to 14.0 MeV energy range in steps of 0.25 MeV using the activation technique. After activation of the 0.5 inch diameter and 442 mg 238U foil, the activity of the 208 keV characteristic γ-line is tracked for 6 weeks with a high efficient HPGe clover detector to determine the initial activity needed for the cross-section determination. Results of the cross-section measurements, determined relative to 27Al and 197Au neutron activation monitor foils, and the comparison with theoretical models will be presented during the meeting.

U.S. Army Mobility Equipment Research and Development Plan

DTIC Science & Technology

1981-03-01

P LEVEL( ADA 102 7 8 NOIIILITY ISOIIMINT IIISE MICII A DEIIEMOI’MINI COMMAND Al4 198 U.S. ARMY MOBILITY EO,(IJIPME~qNT 1) ITE’V.ZLOPME.NI...8217 PLAN FORT IJELVOIR, VA MAEICII 191 * jDISTII3UTON 3TATE7 N A IAP~rO edIOT U .. ~eI a G Best Available Copy Mobility Equipment Research & DevelopmentC...U.S. ARMY MOBILITY EQUIPMEN9 RESEARCH AND DEVELOPMENT- MOBILITY SURVIVABILITY ENERGI C) LU P= _ _ \\ ii]MAR8I earch & Development Command ~3 QUIPMENT

Magnetic ground state and electronic structure of CeRu(2)Al(10).

PubMed

Goraus, Jerzy; Ślebarski, Andrzej

2012-03-07

We present a combined theoretical and experimental study of the electronic structure for CeRu(2)Al(10) based on ab initio band structure calculations and x-ray photoemission spectroscopy (XPS) data. Our calculations were performed for the base unit cell and for the hypothetical unit cell which enables antiferromagnetic ordering. The stability of the magnetic phase was investigated within fixed spin moment calculations. When additional 4f correlations are not included in the LSDA C U approach, CeRu(2)Al(10) exhibits an unstable magnetic configuration with the difference in total energy per unit cell between the weakly magnetic state and the non-magnetic one of the order ~0.3 meV. We found that Coulomb correlations among 4f electrons, when they are included in the LSDA C U approach, stabilize the magnetic structure. In the weakly correlated system (small U) an antiferromagnetic (AFM) ground state with the lowest total energy is preferred. The situation is, however, the opposite when the 4f correlations are strong. In this case the ferromagnetic (FM) ground state is preferred. By comparing our calculations with the experimental data we conclude that the 4f correlations in CeRu(2)Al(10) are weak. We also carried out a structural relaxation of atomic positions within the Cmcm unit cell and we found that the Al atoms exhibit noticeable displacement from their positions known from x-ray diffraction (XRD) analysis.

Microstructure of as-fabricated UMo/Al(Si) plates prepared with ground and atomized powder

NASA Astrophysics Data System (ADS)

Jungwirth, R.; Palancher, H.; Bonnin, A.; Bertrand-Drira, C.; Borca, C.; Honkimäki, V.; Jarousse, C.; Stepnik, B.; Park, S.-H.; Iltis, X.; Schmahl, W. W.; Petry, W.

2013-07-01

UMo-Al based fuel plates prepared with ground U8wt%Mo, ground U8wt%MoX (X = 1 wt%Pt, 1 wt%Ti, 1.5 wt%Nb or 3 wt%Nb) and atomized U7wt%Mo have been examined. The first finding is that that during the fuel plate production the metastable γ-UMo phases partly decomposed into two different γ-UMo phases, U2Mo and α'-U in ground powder or α″-U in atomized powder. Alloying small amounts of a third element to the UMo had no measurable effect on the stability of the γ-UMo phase. Second, the addition of some Si inside the Al matrix and the presence of oxide layers in ground and atomized samples is studied. In the case with at least 2 wt%Si inside the matrix a Silicon rich layer (SiRL) forms at the interface between the UMo and the Al during the fuel plate production. The SiRL forms more easily when an Al-Si alloy matrix - which is characterized by Si precipitates with a diameter ⩽1 μm - is used than when an Al-Si mixed powder matrix - which is characterized by Si particles with some μm diameter - is used. The presence of an oxide layer on the surface of the UMo particles hinders the formation of the SiRL. Addition of some Si into the Al matrix [7-11]. Application of a protective barrier at the UMo/Al interface by oxidizing the UMo powder [7,12]. Increase of the Mo content or use of UMo alloys with ternary element addition X (e.g. X = Nb, Ti, Pt) to stabilize the γ-UMo with respect to α-U or to control the UMo-Al interaction layer kinetics [9,12-24]. Use of ground UMo powder instead of atomized UMo powder [10,25] The points 1-3 are to limit the formation of the undesired UMo/Al layer. Especially the addition of Si into the matrix has been suggested [3,7,8,10,11,26,27]. It has been often mentioned that Silicon is efficient in reducing the Uranium-Aluminum diffusion kinetics since Si shows a higher chemical affinity to U than Al to U. Si suppresses the formation of brittle UAl4 which causes a huge swelling during the irradiation. Furthermore it enhances the

Afghanistan: Post-Taliban Governance, Security, and U.S. Policy

DTIC Science & Technology

2010-09-17

plant in Sudan (Al Shifa) believe to be producing chemical weapons for Al Qaeda also was struck that day, although U.S. reviews later corroborated...Sudan’s assertions that the plant was strictly civilian in nature. 6 http://www.msnbc.msn.com/id/4540958. Afghanistan: Post-Taliban Governance...point where it might not be commercially profitable for China Metallurgical Group, includes construction of two coal-fired electric power plant (one

Diagenesis of fossil coral skeletons: Correlation between trace elements, textures, and [sup 234]U/[sup 238]U

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bar-Matthews, M.; Wasserburg, G.J.; Chen, J.H.

1993-01-01

A comparative study of Pleistocene fossil coral skeletons and of modern coral skeletons was carried out using petrographic and trace element analyses on a suite of Pleistocene samples that had previously been studied from [sup 234]U, [sup 230]Th, and U-[sup 230]Th ages (Chen et al. 1991). Evidence of a range of diagenetic changes can be recognized by optical (OM) and scanning electron microscopy (SEM). Using an electron microprobe and SEM, concentrations of Na, S, Sr, and Mg were measured. No other trace elements were detected. Na, S, and Mg contents of the matrix, the fibrous micropores, and radiating needles aremore » highly variable and well correlated. High concentrations of Na, S, and Mg were found in modern living corals with lower concentrations in fossil corals and fibrous micropores, and the lowest value in the radiating needles. The reason for the correlations of Na, S, and Mg and crystal chemistry and the response to diagenesis of these trace elements is not understood. The average concentrations of Na, S, and Mg for each sample, when plotted against the whole coral initial [delta][sup 234]U, are generally correlated (Chen et al., 1991). As all these diagenetic changes involve the recystallization and deposition of aragonite, the authors infer that the geologic site of diagenesis both for forming the secondary aragonitic phases and for the enhancement of the [sup 234]U content in the fossil corals was the marine environment. It is possible that the textural and Na, S, and Mg trace element contents of fossil corals be used to ascertain the reliability of fossil coral skeletons for U-[sup 230]Th dating. The basic problem of identifying a priori unaltered coral skeletons for [sup 230]Th dating is not yet resolved. 64 refs., 16 figs., 5 tabs.« less

Direct U-Pb dating of Cretaceous and Paleocene dinosaur bones, San Juan Basin, New Mexico: COMMENT

USGS Publications Warehouse

Koenig, Alan E.; Lucas, Spencer G.; Neymark, Leonid A.; Heckert, Andrew B.; Sullivan, Robert M.; Jasinski, Steven E.; Fowler, Denver W.

2012-01-01

Based on U-Pb dating of two dinosaur bones from the San Juan Basin of New Mexico (United States), Fassett et al. (2011) claim to provide the first successful direct dating of fossil bones and to establish the presence of Paleocene dinosaurs. Fassett et al. ignore previously published work that directly questions their stratigraphic interpretations (Lucas et al., 2009), and fail to provide sufficient descriptions of instrumental, geochronological, and statistical treatments of the data to allow evaluation of the potentially complex diagenetic and recrystallization history of bone. These shortcomings lead us to question the validity of the U-Pb dates published by Fassett et al. and their conclusions regarding the existence of Paleocene dinosaurs.

Microstructural analysis of as-processed U-10 wt.%Mo monolithic fuel plate in AA6061 matrix with Zr diffusion barrier

NASA Astrophysics Data System (ADS)

Perez, E.; Yao, B.; Keiser, D. D., Jr.; Sohn, Y. H.

2010-07-01

For higher U-loading in low-enriched U-10 wt.%Mo fuels, monolithic fuel plate clad in AA6061 is being developed as a part of Reduced Enrichment for Research and Test Reactor (RERTR) program. This paper reports the first characterization results from a monolithic U-10 wt.%Mo fuel plate with a Zr diffusion barrier that was fabricated as part of a plate fabrication campaign for irradiation testing in the Advanced Test Reactor (ATR). Both scanning and transmission electron microscopy (SEM and TEM) were employed for analysis. At the interface between the Zr barrier and U-10 wt.%Mo, going from Zr to U(Mo), UZr 2, γ-UZr, Zr solid-solution and Mo 2Zr phases were observed. The interface between AA6061 cladding and Zr barrier plate consisted of four layers, going from Al to Zr, (Al, Si) 2Zr, (Al, Si)Zr 3 (Al, Si) 3Zr, and AlSi 4Zr 5. Irradiation behavior of these intermetallic phases is discussed based on their constituents. Characterization of as-fabricated phase constituents and microstructure would help understand the irradiation behavior of these fuel plates, interpret post-irradiation examination, and optimize the processing parameters of monolithic fuel system.

Photon stimulated desorption from oxidized Al(110). [Surface hydroxyls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, E.D.; Garrett, R.F.; Knotek, M.L.

1987-01-01

We have studied oxide films on Al(110) by photon stimulated desorption (PSD) on the Bell Labs U4 PGM at the National Synchrotron Light Source. Utilizing a time of flight technique we have obtained ion energy distribution (IED) and relative ion yield (RIY) data at the Al 2p and O 1s edges for oxides prepared at various temperatures. These initial studies suggest that different sites for the surface hydroxyls exist, that they can be selectively prepared, and examined by PSD. 15 refs., 9 figs.

Desarrollo y validación de una nueva tecnología, basada en arginina al 1.5%, un compuesto de calcio insoluble y fluoruro, para el uso diario en la prevención y tratamiento de la caries dental.

PubMed

Cummins, D

2013-10-22

este artículo discute brevemente la prevalencia de caries, la naturaleza multifactorial de su etiología, el riesgo de caries y el papel y eficacia del fluoruro. Resalta también la investigación sobre el metabolismo bacteriano, que ha aportado conocimientos sobre la defensa natural oral contra la caries y la base para el desarrollo de una nueva tecnología para la prevención diaria y el tratamiento de la caries. Por último, se resume la evidencia que respalda que la tecnología complementa y mejora la eficacia anti-caries de la crema dental con fluoruro. los datos globales muestran que a pesar de la exitosa introducción del fluoruro, la caries dental es una enfermedad prevalente. La experiencia de caries depende del balance entre el consumo de azúcares, la higiene oral y el uso del fluoruro. Hay tres conceptos científicos que son fundamentales en las nuevas mediciones para detectar, tratar y monitorear la caries: (1) la caries dental es un proceso dinámico, (2) la caries dental es un proceso continuo de etapas que van desde reversible (pre-clínica) hasta irreversible (lesiones clínicamente detectables), y (3) el proceso de la caries es un balance de factores patológicos y protectores que pueden modularse para el manejo de la caries. El fluoruro funciona como factor protector al detener y revertir el proceso de la caries, pero el fluoruro no previene los factores patológicos que inician el proceso. Se ha identificado una tecnología novedosa, basada en arginina y un compuesto insoluble de calcio, que está dirigida a la placa dental para prevenir la iniciación del proceso de caries al reducir los factores patológicos. Como los mecanismos de acción de la arginina y el fluoruro son altamente complementarios, se ha desarrollado un nuevo dentífrico que combina la arginina y el fluoruro, y se ha probado clínicamente que brinda una prevención superior contra la caries. Copyright © 2013 Elsevier Ltd. All rights reserved.

Radiation characteristics of Al wire arrays on Z*

NASA Astrophysics Data System (ADS)

Coverdale, C. A.; Ampleford, D. J.; Jones, B.; Cuneo, M. E.; Hansen, S.; Jennings, C. A.; Moore, N.; Jones, S. C.; Deeney, C.

2011-10-01

Analysis of mixed material nested wire array experiments at Z have shown that the inner wire array dominates the hottest regions of the stagnated z pinch. In those experiments, substantial free-bound continuum radiation was observed when Al was fielded on the inner wire array. Experiments with Al (5% Mg) on both wire arrays have also been fielded, with variations in the free-bound continuum observed. These variations appear to be tied to the initial mass and diameter of the wire array. The results presented here will investigate the trends in the measured emission (Al and Mg K-shell and free-bound continuum) and will compare the measured output to more recent Al wire array experimental results on the refurbished Z accelerator. *Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. +current address: NNSA/DOE Headquarters, Washington D.C.

Counterterrorism and Counterinsurgency in Somalia: Assessing the Campaign Against Al Shabaab

DTIC Science & Technology

2016-01-01

establishment of Islam.”11 Research Design In an effort to better understand al Shabaab and U.S. efforts to degrade it, this study asks three sets of questions...and International Studies , July 2011; Ken Menkhaus, “Al-Shabab’s Capabilities Post -Westgate,” CTC Sentinel, March 24, 2014; United Nations (UN...representation of RAND intellectual property is provided for noncommercial use only. Unauthorized posting of this publication online is prohibited

U-Pb (SHRIMP) Ages of Be and U-rich Opal in Tuffaceous Breccia at Spor Mountain, Utah: Interpreting a Record of Continuous Opal Formation, Episodic Be-U Mineralization, and Remobilization Events

NASA Astrophysics Data System (ADS)

Ayuso, R. A.; Vazquez, J. A.; Foley, N.; Lederer, G.; Jaskula, B.

2016-12-01

The Spor Mountain Fm. (SMF, ca. 21 Ma; Lindsey, 1977, Eco. Geol., v. 72, 219-232; Foley et al., 2012, USGS SIR 2010-5070-F, 1-43) hosts the largest deposit of volcanogenic-epithermal Be in the world (proven reserves 15,700 t/contained Be). Ore occurs mainly in cm-to-m-wide irregularly layered nodules of calcite, chalcedony, opal, fluorite, and bertrandite (Be4Si2O7(OH)2) in tuff breccias. U-Pb SHRIMP dating (adapted from Paces et al., 2004, GCA v. 68, 1591-1606; Neymark and Paces, 2013, EPSL v. 361, 98-109) of opal in nodules from SMF yielded 206Pb/238U ages coupled with multi-element analyses, e.g., Be, F, P, Si, Ti, REE, etc. The ages reveal periods of prolonged massive and fracture-filling opal formation that range from 55 Ma to 2 Ma. Age gaps are not prominent (a previous study of bulk samples identified opal ages of 21.8 Ma, 13-16 Ma, 8-9 Ma in SMF and 3.5 Ma in the overlying 6 Ma Topaz Mountain Fm.; Ludwig et al., 1980, EPSL, v. 46, 221-232). High values of Be/Si ( 5,000-20,000), Be/F, Be/P, and Be/U and oldest ages ( 55 to 28 Ma) occur in opal in nodule cores; outward, younger opal layers ( 28 to 7 Ma) decline in Be/Si but also include spikes of >5,000. A prominent U/Si spike (>300) occurs in opal between 6 Ma and 4 Ma, which may establish the age of U mineralization that occurs immediately east of Spor Mountain (the Yellow Chief U deposit). The occurrence of Be-rich opal older than 25 Ma in nodules within the 21 Ma (K-Ar date) tuff suggests that nodule formation may also be associated with older volcanism in the region. Opal that is younger than 21 Ma is thought to have formed by hydrothermal fluid interacting with Be-rich tuff. Geochemical modeling shows leaching of Be and other elements from volcanic glass and deposition of bertrandite upon reaction of the fluid with carbonate clasts in the tuff are viable mechanisms for the observed assemblages. Be concentrations in late nodular opal (<6 Ma) may reflect redistribution of earlier mineralization. The world

Autoguía para el telescopio 2,15 mts de CASLEO

NASA Astrophysics Data System (ADS)

Aballay, J. A.; Casagrande, A. R.; Pereyra, P. F.; Marún, A. H.

Se está desarrollando un sistema de autoguía para el telescopio de 2,15 mts. El mismo se realizará aprovechando el Offset Guider. Al ocular móvil de éste se vinculará alguna cámara digital (ST4-ST7-CH250) para lograr la visión del objeto. El funcionamiento del equipo será el siguiente: primero, dadas las coordenadas del objeto a observar, se tomarán las coordenadas del telescopio para que, a través de una base de datos, se determine un campo de objetos que sirvan para la cámara de visión, luego, la PC obtendrá el offset entre la estrella de observación y la estrella seleccionada como guía, este valor será trasladado a los motores que posicionarán en forma automática el ocular. Una vez que la estrella es visualizada en la cámara (monitor de PC ) se correrá el programa que guiará el telescopio automáticamente.

Doping effects on UPd 2Al 3

NASA Astrophysics Data System (ADS)

Geibel, C.; Schank, C.; Jährling, F.; Buschinger, B.; Grauel, A.; Lühmann, T.; Gegenwart, P.; Helfrich, R.; Reinders, P. H. P.; Steglich, F.

1994-04-01

We present first results of a doping study on the U site on UPd 2Al 3. These results give further support for a tetravalent uranium configuration and an induced type of antiferromagnetic ordering. They confirm the importance of an unperturbed electronic configuration for both antiferromagnetic long-range ordering and heavy-fermion superconductivity. Implications for the interaction between both phenomena are discussed.

U-Pb ID-TIMS zircon ages of TTG gneisses of the Aravalli Craton of India

NASA Astrophysics Data System (ADS)

Chauhan, Hiredya; Saikia, Ashima; Kaulina, Tatiana; Bayanova, Tamara; Ahmad, Talat

2015-04-01

The crystalline basement of the Aravalli Craton is a heterogeneous assemblage dominated by granitic gneisses and granites with sporadic occurrences of amphibolites and dismembered sedimentary enclaves (Upadhyaya et al., 1992). This assemblage is known to have experienced multiple deformation and metamorphic events followed by emplacement of voluminous granites and basaltic dykes. Based on Sm-Nd whole rock data on the basement Mewar orthogneisses of Jhamarkotra region (Gopalan et al., 1990) and Pb/Pb ages of zircon from Gingla Granites which intrudes the basement (Wiedenbeck et al., 1996), it has been inferred that the whole magmatic episode leading to the formation of the basement spanned from 3300 to 2400 Ma and that the Aravalli cratonic block had broadly stabilized by 2500 Ma on which the younger Aravalli and Delhi Supergroup unconformably deposited. However, no comprehensive age data on the basement gneisses from the study area spanning the entire magmatic episode is available. This work attempts to provide a time frame work for evolution of the basement gneisses of the Aravalli Craton. We present here U-Pb zircon ages from the Precambrian basement TTG gneisses of the Aravalli Craton of north western India. Pb and U were measured on multicollector Finnigan-MAT 262 mass spectrometer. The temperatures of measurements were 1300°C for Pb and 1500°C for U. Pb isotope ratios were corrected for mass fractionation with a factor of 0.10% per amu, based on repeat analyses of the standard NBS SRM 982. The U analyses were corrected for mass fractionation with a factor of 0.003% per amu, based on repeat analyses of the NBS U 500 standard. Reproducibility of the U-Pb ratios was determined from the repeated analysis of standard zircon IGFM-87 (Ukraine) and taken as 0.5% for 207Pb/235U and 206Pb/238U ratios, respectively, at 95% confidence level. All calculations were done using the programs PBDAT and ISOPLOT (Ludwig 1991, 2008). Four zircon fractions corresponding to four

Positron production in heavy-ion collisions. II. Application of the formalism to the case of the U+U collision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomoda, T.

1982-07-01

The method developed in the preceding paper is applied to the calculation of the spectra of positrons produced in the U + U collision. Matrix elements of the radial derivative operator between adiabatic basis states are calculated in the monopole approximation, with the finite nuclear size taken into account. These matrix elements are then modified for the supercritical case with the use of the analytical method presented in paper I of this series. The coupled differential equations for the occupation amplitudes of the basis states are solved and the positron spectra are obtained for the U + U collision. Itmore » is shown that the decomposition of the production probability into a spontaneous and an induced part depends on the definition of the resonance state and cannot be given unambiguously. The results are compared with those obtained by Reinhardt et al.« less

Afghanistan: Post-Taliban Governance, Security, and U.S. Policy

DTIC Science & Technology

2010-04-04

recent projects include Bagrami office park, Herat Industrial Park, Coca Cola plant , Safi mall in Kabul; Aynak copper mine in Lowgar (China); an...5 A pharmaceutical plant in Sudan (Al Shifa) believe to be producing chemical weapons for Al Qaeda also was struck that day, although U.S. reviews...later corroborated Sudan’s assertions that the plant was strictly civilian in nature. 6 http://www.msnbc.msn.com/id/4540958 Afghanistan: Post

U-series constraints on the Holocene human presence in the Cuatro Cienegas basin, Mexico

NASA Astrophysics Data System (ADS)

Noble, S. R.; Felstead, N.; Gonzalez, S.; Leng, M. J.; Metcalfe, S. E.; Patchett, P. J.

2010-12-01

tracer calibrated against gravimetric solutions prepared from Ames high-purity Th metal crystal and CRM 112a U metal ingot rather than natural materials of assumed secular equilibrium. ICP-MS mass bias and Faraday-SEM gain was monitored using CRM 112a and an in-house 229Th-230Th-232Th solution. Most samples have relatively high U contents (~2 ppm U), moderate [230Th/232Th] = 29-44, and initial [234U/238U] ~ 1.92. We obtain an age of 7.24 ± 0.13 ka BP for this trackway based on an average of two samples of the uppermost tufa surface. Depth profiling of one sample shows consistently increasing age downwards (~370 a/cm). [1] Gonzalez, A.H.G. et al., 2006, Ichnos 16, 12-24;[2] Souza, V. et al., 2006, PNAS 103, 6565-6570; [3] Johannesson, K.H. et al., 2004, J.S.Am.Earth Sci. 17, 171-180; [4] Meyer, E. 1973, Ecology 54, 982-995; [5] Minckley, T.A. & Jackson, S. 2008. J. Biogeography 35, 188-190; [6] Edwards, R.L. et al., 1987, EPSL 81, 175-192; [8] Cheng, H. et al., 2000, Chem. Geol. 169, 17-33; [8] Potter, E.K. et al., 2005, EPSL 247, 10-17.

U-Th-Pb and Rb-Sr systematics of Allende and U-Th-Pb systematics of Orgueil

USGS Publications Warehouse

Tatsumoto, M.; Unruh, D.M.; Desborough, G.A.

1976-01-01

U-Th-Pb systematics study of Allende inclusions showed that U, Th and Sr concentrations in Ca, Al (pyroxene)-rich chondrules and white and pinkish-white aggregate separates of Allende are five to ten times higher than those of the matrix, whereas Mg (olivine)-rich chondrules have U and Th concentrations about twice as high as the matrix. Th concentrations are extremely high in white aggregates and in pinkish-white (spinel-rich) aggregates while U and Sr concentrations in white aggregates are more than twice as high as those in pinkish-white aggregates. Large enrichment of these refractory elements in the white aggregates indicates that they contain high-temperature condensates from the solar nebula. The Pb concentrations in the inclusions are less than half of those in the whole rock and matrix, indicating that the matrix is a lower-temperature condensate. The isotopic composition of lead in the matrix is less radiogenic than that of the whole meteorite, whereas lead in Ca- and Al-rich chondrules and aggregates is extremely radiogenic. The 206Pb/204Pb ratio reaches as high as 55.9 in a white aggregate separate. The lead of Mg-rich chondrules is moderately radiogenic and the 206Pb/204Pb ratio ranges from 18 to 26. A striking linear relationship exists among leads in the chondrules, aggregates and matrix on the 207Pb/204Pb vs 204Pb/204Pb plot. The slope of the best fit line is 0.6188 ?? 0.0016, yielding an isochron age of 4553 ?? 4 m.y. The regression line passes through primordial lead values obtained from Canyon Diablo troilite. The data, when corrected for Canyon Diablo troilite Pb and plotted on a U-Pb concordia diagram, show that the pink and white aggregates and the Ca-Al-rich and Mg-rich inclusions have excess Pb and define a chord which intersects the concordia curve at 4548 ?? 25 m.y. and 107 ?? 70 m.y. The intercepts might correspond to the agglomeration age of the meteorite and a time of probably later disturbance, respectively. The matrix and some

The regolith portion of the lunar meteorite Sayh al Uhaymir 169

NASA Astrophysics Data System (ADS)

Al-Kathiri, A.; Gnos, E.; Hofmann, B. A.

Sayh al Uhaymir (SaU) 169 is a composite lunar meteorite from Oman that consists of polymict regolith breccia (8.44 ppm Th), adhering to impact-melt breccia (IMB; 32.7 ppm Th). In this contribution we consider the regolith breccia portion of SaU 169, and demonstrate that it is composed of two generations representing two formation stages, labeled II and III. The regolith breccia also contains the following clasts: Ti-poor to Ti-rich basalts, gabbros to granulites, and incorporated regolith breccias. The average SaU 169 regolith breccia bulk composition lies within the range of Apollo 12 and 14 soil and regolith breccias, with the closest correspondence being with that of Apollo 14, but Sc contents indicate a higher portion of mare basalts. This is supported by relations between Sm-Al2O3, FeO-Cr2O3-TiO2, Sm/Eu and Th-K2O. The composition can best be modeled as a mixture of high-K KREEP, mare basalt and norite/troctolite, consistent with the rareness of anorthositic rocks. The largest KREEP breccia clast in the regolith is identical in its chemical composition and total REE content to the incompatible trace-element (ITE)- rich high-K KREEP rocks of the Apollo 14 landing site, pointing to a similar source. In contrast to Apollo 14 soil, SaU 169 IMB and SaU 169 KREEP breccia clast, the SaU 169 regolith is not depleted in K/Th, indicating a low contribution of high-Th IMB such as the SaU 169 main lithology in the regolith. The data presented here indicate the SaU 169 regolith breccia is from the lunar front side, and has a strong Procellarum KREEP Terrane signature.

Diseño y Operación de un Secador Solar de Madera para Países Tropicales

Treesearch

Brian Bond; Omar Espinoza; Philip Araman

2011-01-01

La madera es usualmente secada a un contenido de humedad específico antes de ser transformada en productos finales. A pesar de que la madera puede ser secada al aire, la humedad ambiental en la mayoría de las ubicaciones previene a la madera alcanzar el contenido de humedad necesario para su estabilidad dimensional y adecuado procesamiento, especialmente para usos de...

VIEW OF TENNESSEE COAL & IRON (TCI) U.S. STEEL, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF TENNESSEE COAL & IRON (TCI) - U.S. STEEL, ENSLEY RAIL MILL SITE. POWERHOUSE IN LEFT BACKGROUND, MIXER IN RIGHT FOREGROUND. - Tennessee Coal & Iron Company, Ensley Works, West of residential & commercial districts, Birmingham, Jefferson County, AL

Sobre la terapia génica para enfermedades de la retina.

PubMed

Fischer, M Dominik

2017-07-11

Las mutaciones en un gran número de genes provocan degeneración de la retina y ceguera sin que exista actualmente cura alguna. En las últimas décadas, la terapia génica para enfermedades de la retina ha evolucionado y se ha convertido en un nuevo y prometedor paradigma terapéutico para estas enfermedades poco comunes. Este artículo refleja las ideas y los conceptos que parten de la ciencia básica hacia la aplicabilidad de la terapia génica en el ámbito clínico. Se describen los avances y las reflexiones actuales sobre la eficacia de los ensayos clínicos en la actualidad y se discuten los posibles obstáculos y soluciones de cara al futuro de la terapia génica para enfermedades de la retina. © 2017 S. Karger AG, Basel.

Microscopic Magnetic Properties of the Itinerant Metamagnet UCoAl by X-ray Magnetic Circular Dichroism

NASA Astrophysics Data System (ADS)

Combier, Tristan; Palacio-Morales, Alexandra; Sanchez, Jean-Pierre; Wilhelm, Fabrice; Pourret, Alexandre; Brison, Jean-Pascal; Aoki, Dai; Rogalev, Andrei

2017-02-01

The itinerant metamagnet UCoAl has been investigated by high field X-ray magnetic circular dichroism (XMCD) at the U M4,5 and Co K edges. The orbital and spin moments of U at 2.1 K for H || c applied below and above the first order metamagnetic transition field (HM) have been determined. The magnetism of UCoAl is dominated by the U moment. There is no evidence for any change of the orbital to spin moment ratio (˜-2.05) across HM and within the ferromagnetic phase up to 17 T. The possibility of a Fermi surface reconstruction at HM remains an open option. XMCD at the Co K-edge reveals the presence of a small Co 4p-orbital moment parallel to the macroscopic magnetization. In addition, the Co 3d-moment is estimated to be at most 0.1 μB at 17 T. The similar field dependence of the U and Co magnetizations indicates that the Co moment is induced by the U moment.

Remodelar Correctamente: Guía de Prácticas Acreditadas Seguras Para Trabajar Con Plomo

EPA Pesticide Factsheets

Información general sobre los requisitos legales de las prácticas relacionadas al manejo seguro del plomo para dueños de hogares, inquilinos, proveedores de cuido infantil, y padres durante las actividades de remodelación

Electron capture in collisions of Al2+ ions with He atoms at intermediate energies

NASA Astrophysics Data System (ADS)

Watanabe, A.; Sato, H.; Gu, J. P.; Hirsch, G.; Buenker, R. J.; Kimura, M.

2001-09-01

Electron capture resulting from collisions of Al2+ ions with He atoms from 0.15 to 1000 keV/u is investigated using a molecular-orbital representation within a semiclassical frame. Molecular electronic states and corresponding couplings are determined by the ALCHEMY program. Sixteen molecular states all connecting to single-electron-capture processes are included, and hence radial and rotational couplings among these channels are fully considered. The trajectory effect arising from the straight-line, Coulomb, and ground-state potential trajectories for electron-capture and excitation processes is carefully assessed. The electron-capture cross section by ground-state Al2+(2S) ions slowly increases before it reaches a maximum of 1.3×10-16 cm2 at 100 keV/u. Those for metastable Al2+(2P) ions sharply increase with increasing energy, and reach a peak at 1 keV/u with a value of 1.5×10-16 cm2. The earlier experimental data are found to be larger by an order of magnitude although their energy dependence is in good accord with the present result. Excitation cross sections for both the ground and metastable states are found to be much larger by a factor of 2-3 than corresponding capture cross sections above 1 keV/u although they become comparable below this energy.

Estimating customer electricity savings from projects installed by the U.S. ESCO industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carvallo, Juan Pablo; Larsen, Peter H.; Goldman, Charles A.

The U.S. energy service company (ESCO) industry has a well-established track record of delivering substantial energy and dollar savings in the public and institutional facilities sector, typically through the use of energy savings performance contracts (ESPC) (Larsen et al. 2012; Goldman et al. 2005; Hopper et al. 2005, Stuart et al. 2013). This ~$6.4 billion industry, which is expected to grow significantly over the next five years, may play an important role in achieving demand-side energy efficiency under local/state/federal environmental policy goals. To date, there has been little or no research in the public domain to estimate electricity savings formore » the entire U.S. ESCO industry. Estimating these savings levels is a foundational step in order to determine total avoided greenhouse gas (GHG) emissions from demand-side energy efficiency measures installed by U.S. ESCOs. We introduce a method to estimate the total amount of electricity saved by projects implemented by the U.S. ESCO industry using the Lawrence Berkeley National Laboratory (LBNL) /National Association of Energy Service Companies (NAESCO) database of projects and LBNL’s biennial industry survey. We report two metrics: incremental electricity savings and savings from ESCO projects that are active in a given year (e.g., 2012). Overall, we estimate that in 2012 active U.S. ESCO industry projects generated about 34 TWh of electricity savings—15 TWh of these electricity savings were for MUSH market customers who did not rely on utility customer-funded energy efficiency programs (see Figure 1). This analysis shows that almost two-thirds of 2012 electricity savings in municipal, local and state government facilities, universities/colleges, K-12 schools, and healthcare facilities (i.e., the so-called “MUSH” market) were not supported by a utility customer-funded energy efficiency program.« less

La función de la EPA para la protección contra la radiación

EPA Pesticide Factsheets

Conforme al mandato congresional, la Agencia de Protección Ambiental de EE.UU. el la entidad responsable de establecer normas para proteger la salud humana y el medioambiente de materiales radioactivos.

Fission Product Yield Study of 235U, 238U and 239Pu Using Dual-Fission Ionization Chambers

NASA Astrophysics Data System (ADS)

Bhatia, C.; Fallin, B.; Howell, C.; Tornow, W.; Gooden, M.; Kelley, J.; Arnold, C.; Bond, E.; Bredeweg, T.; Fowler, M.; Moody, W.; Rundberg, R.; Rusev, G.; Vieira, D.; Wilhelmy, J.; Becker, J.; Macri, R.; Ryan, C.; Sheets, S.; Stoyer, M.; Tonchev, A.

2014-05-01

To resolve long-standing differences between LANL and LLNL regarding the correct fission basis for analysis of nuclear test data [M.B. Chadwick et al., Nucl. Data Sheets 111, 2891 (2010); H. Selby et al., Nucl. Data Sheets 111, 2891 (2010)], a collaboration between TUNL/LANL/LLNL has been established to perform high-precision measurements of neutron induced fission product yields. The main goal is to make a definitive statement about the energy dependence of the fission yields to an accuracy better than 2-3% between 1 and 15 MeV, where experimental data are very scarce. At TUNL, we have completed the design, fabrication and testing of three dual-fission chambers dedicated to 235U, 238U, and 239Pu. The dual-fission chambers were used to make measurements of the fission product activity relative to the total fission rate, as well as for high-precision absolute fission yield measurements. The activation method was employed, utilizing the mono-energetic neutron beams available at TUNL. Neutrons of 4.6, 9.0, and 14.5 MeV were produced via the 2H(d,n)3He reaction, and for neutrons at 14.8 MeV, the 3H(d,n)4He reaction was used. After activation, the induced γ-ray activity of the fission products was measured for two months using high-resolution HPGe detectors in a low-background environment. Results for the yield of seven fission fragments of 235U, 238U, and 239Pu and a comparison to available data at other energies are reported. For the first time results are available for neutron energies between 2 and 14 MeV.

Thermal conductivity of fresh and irradiated U-Mo fuels

NASA Astrophysics Data System (ADS)

Huber, Tanja K.; Breitkreutz, Harald; Burkes, Douglas E.; Casella, Amanda J.; Casella, Andrew M.; Elgeti, Stefan; Reiter, Christian; Robinson, Adam. B.; Smith, Frances. N.; Wachs, Daniel. M.; Petry, Winfried

2018-05-01

The thermal conductivity of fresh and irradiated U-Mo dispersion and monolithic fuel has been investigated experimentally and compared to theoretical models. During in-pile irradiation, thermal conductivity of fresh dispersion fuel at a temperature of 150 °C decreased from 59 W/m·K to 18 W/m·K at a burn-up of 4.9·1021 f/cc and further to 9 W/m·K at a burn-up of 6.1·1021 f/cc. Fresh monolithic fuel has a considerably lower thermal conductivity of 15 W/m·K at a temperature of 150 °C and consequently its decrease during in-pile irradiation is less steep than for dispersion fuel. For a burn-up of 3.5·1021 f/cc of monolithic fuel, a thermal conductivity of 11 W/m·K at a temperature of 150 °C has been measured by Burkes et al. (2015). The difference of decrease for both fuels originates from effects in the matrix that occur during irradiation, like for dispersion fuel the gradual disappearance of the Al matrix with increased burn-up and the subsequent growth of an interaction layer (IDL) between the U-Mo fuel particle and Al matrix and subsequent matrix hardening. The growth of fission gas bubbles and the decomposition of the U-Mo crystal lattice also affect both dispersion and monolithic fuel.

Thermal conductivity of fresh and irradiated U-Mo fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huber, Tanja K.; Breitkreutz, Harald; Burkes, Douglas E.

The thermal conductivity of fresh and irradiated U-Mo dispersion and monolithic fuel has been investigated experimentally and compared to theoretical models. During in-pile irradiation, the thermal conductivity of fresh dispersion fuel at a temperature of 150°C decreases from 59 W/m ·K down to 18  W/m ·K at a burn-up of 4.9 ·10 21 f/cc and further down to 9 W/m·K at a burn-up of 6.1·10 21 f/cc. Fresh monolithic fuel has a considerably lower thermal conductivity of 15 W/m·K at a temperature of 150 °C and consequently its decrease during in-pile irradiation is less steep as for the dispersion fuel. For a burn-up ofmore » 3.5·10 21 f /cc of monolithic fuel 11 W/m·K at a temperature of 150 °C has been measured by Burkes et al. The difference of the decrease of both fuels originates from effects in the matrix that occur during irradiation, like for dispersion fuel the gradual disappearance of the Al matrix with increasing burn-up and the subsequent growth of an interaction layer (IDL) between the U-Mo fuel particle and Al matrix and subsequent matrix hardening. The growth of fission gas bubbles and the decomposition of the U-Mo crystal lattice affects both dispersion and monolithic fuel.« less

Ortho-para-H2 conversion by hydrogen exchange: comparison of theory and experiment.

PubMed

Lique, François; Honvault, Pascal; Faure, Alexandre

2012-10-21

We report fully-quantum time-independent calculations of cross sections and rate coefficients for the collisional (de)excitation of H(2) by H. Our calculations are based on the H(3) global potential energy surface of Mielke et al. [J. Chem. Phys. 116, 4142 (2002)]. The reactive hydrogen exchange channels are taken into account. We show that the ortho-para and para-ortho conversion of H(2) are significant processes at temperatures above ~300 K and for the last process we provide the first comparison with available experimental rate coefficients between 300 and 444 K. The good agreement between theory and experiment is a new illustration of our detailed understanding of the simplest chemical reaction. The importance of the ortho-para-H(2) conversion by hydrogen exchange in astrophysics is discussed.

Precision measurement of ^23Al beta-decay

NASA Astrophysics Data System (ADS)

Zhai, Yongjun; Iacob, V. E.; Hardy, J. C.; Al-Abdullah, T.; Banu, A.; Fu, C.; Golovko, V. V.; McCleskey, M.; Nica, N.; Park, H. I.; Tabacaru, G.; Tribble, R. E.; Trache, L.

2007-10-01

The beta-decay of ^23Al (See [1]) was re-measured with higher statistics and better accuracy at Texas A&M University. Using MARS we produced and separated pure ^23Al at 4000 pps, with a 48 MeV/u ^24Mg beam via the ^24Mg (p, 2n)^ 23Al reaction on a H2 cryogenic target. New β and β-γ coincidence measurements were made with a scintillator, an HPGe detector with BGO shielding and the fast tape transport system. The BGO Compton shield very much improved the quality of the γ spectra around the transition from the IAS state at 7803 keV. From the measured β singles and β-γ coincidence decay spectra we obtained an improved β-decay scheme and a more precise lifetime: t=447(4) ms. We use the method of detailed balance to obtain absolute β-branching ratios and absolute logft values for transitions to final states in ^23Mg. For this method, precise efficiency calibration of the HPGe detector up to about 8 MeV is needed. We extended our previous efficiency calibration to the range Eγ=3.5-8 MeV using the β-decay of ^24Al. [1] V.E. Iacob, Y. Zhai et al., Phys. Rev. C 74, 045810 (2006).

First-principles study of transition-metal nitrides as diffusion barriers against Al

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mei, Zhi-Gang; Yacout, Abdellatif M.; Kim, Yeon Soo

2016-04-01

Using density-functional theory based first-principles calculations we provided a comparative study of the diffusion barrier properties of TiN, ZrN, and HfN against Al for U-Mo dispersion fuel applications. We firstly examined the thermodynamic stability of these transition-metal nitrides with Al. The calculated heats of reaction show that both TiN and ZrN are thermodynamically unstable diffusion barrier materials, which might be decomposed by Al at relatively high temperatures. As a comparison, HfN is a stable diffusion barrier material for Al. To evaluate the kinetic stability of these nitride systems against Al diffusion, we investigated the diffusion mechanisms of Al in TiN,more » ZrN and HfN using atomic scale simulations. The effect of non-stoichiometry on the defect formation and Al migration was systematically studied. (C) 2015 ELSEVIER B.V. All rights reserved« less

Rb-Sr and Sm-Nd Isotopic Studies of Martian Depleted Shergottes SaU 094/005

NASA Technical Reports Server (NTRS)

Shih, C.-Y.; Nyquist, L. E.; Reese, Y.

2007-01-01

Sayh al Uhaymir (SaU) 094 and SaU 005 are olivine-phyric shergottites from the Oman desert and are considered as pairs. [e.g., 1]. They are very similar to the Libyan desert shergottite Dar al Gani (DaG) 476 in petrology, chemistry and ejection age [2-6]. This group of shergottites, also recognized as depleted shergottites [e.g. 7] has been strongly shocked and contains very low abundances of light rare earth elements (REE). In addition, terrestrial contaminants are commonly present in meteorites found in desert environments. Age-dating these samples is very challenging, but lower calcite contents in the SaU meteorites suggest that they have been subjected to less severe desert weathering than their DaG counterparts [3-4]. In this report, we present Rb-Sr and Sm-Nd isotopic results for SaU 094 and SaU 005, discuss the correlation of their ages with those of other similar shergottites, and discuss their petrogenesis.

The Proposed U.S.-Colombia Free Trade Agreement: Economic and Political Implications

DTIC Science & Technology

2010-04-16

2008. 50 Ibid, p. 2. 51 Colombia’s Observatorio del Programa Presidencial de DDHH y DIH, Vicepresidencia de la República, April 2008. 52 See CRS...President Alvaro Uribe, “Se Hara Todo el Esfuerzo Para Que No Se Le Niegue el TLC a Colombia, Anuncia el Presidente de Colombia en Entrevista a Caracol...focus of U.S. trade policy as demonstrated by the passage of the North American Free Trade Agreement (NAFTA), the U.S.- Chile Free Trade Agreement, the

Assessing the 40K decay constant by intercalibration with U-Pb, Rb-Sr and K-Ca chronometers

NASA Astrophysics Data System (ADS)

Naumenko-Dèzes, M. O.; Nagler, T. F.; Mezger, K.; Villa, I. M.

2016-12-01

Ar-Ar is one of the most used dating systems and its accuracy plays an important role in constraining the age of planets, durations of processes and their sequence of occurrence. This system has been reported to give ages that are ca. 1% younger than U-Pb ages. The discrepancies between the two mostly used and precise geochronometers, U-Pb and K-Ar, have been a subject of critical reviewing (e.g. Renne et al. [1] and ref. therein) and were attributed to a systematic offset of the 40K decay constant. Multiple attempts to recalibrate it did not achieve consistency.We attempted to intercalibrate three dating systems: U-Pb (the main reference), Rb-Sr (the consistency check) and K-Ca (the unknown). We examined 11 natural samples, but only a phlogopite from the Phalaborwa carbonatite complex met all requirements of a geological "point-like" event [2]. The Rb-Sr age of this sample is 2058.9±5.2 Ma and agrees with the age determined by Nebel et al [3] and with published U-Pb ages. The K-Ca age for the same sample calculated with constants of Steiger&Jäger [4] is 2040±13 Ma, ca.1% younger age than U-Pb reference age of the complex. Since we improved the Ca measurements [5] the K-Ca age has a low uncertainty of 0.6%. This age constrains the decay constant of the Ca branch of the 40K decay. However, the total decay constant is given by one equation with two unknowns, the branching ratio B and the decay constant of the Ar branch.Within the range of published branching ratios (B = 0.892 to 0.896 [6]) the best total 40K decay constant lies mid-way between the values proposed by Renne et al [7] and Min et al [8] (fig. 1).Figure 1. K-Ca age of Phalaborwa phlogopite changes along sloping lines as a function of assumed branching ratio B, calculated with the total 40K decay constant of [3]. [5], [6].[1] Renne et al. (2010) Geochim. Cosmochim Acta 74, 5349-5367; [2] Begemann et al. (2001) Geochim. Cosmochim Acta 65, 111-121; [3] Nebel et al (2010) GCA 74, 5349; [4] Steiger

Harmony and Disharmony: Exploiting al-Qa’ida’s Organizational Vulnerabilities

DTIC Science & Technology

2006-02-14

the authors and not of the U.S. Military Academy, the Department of the Army, or any other agency of the U.S. Government. 3 Table of Contents ...59 4 Foreword Back to table of contents In war, traditional nation-states have specific attributes, such as territory, military...Introduction Back to table of contents A proliferation of research on al-Qa’ida within the last decade has revealed much about the

Improving the characteristics of foundry alloys AlSiCuMg during manufacturing

NASA Astrophysics Data System (ADS)

Fragoso, Bruno Filipe Marques

As piroxenas sao um vasto grupo de silicatos minerais encontrados em muitas rochas igneas e metamorficas. Na sua forma mais simples, estes silicatos sao constituidas por cadeias de SiO3 ligando grupos tetrahedricos de SiO4. A formula quimica geral das piroxenas e M2M1T2O6, onde M2 se refere a catioes geralmente em uma coordenacao octaedrica distorcida (Mg2+, Fe2+, Mn2+, Li+, Ca2+, Na+), M1 refere-se a catioes numa coordenacao octaedrica regular (Al3+, Fe3+, Ti4+, Cr3+, V3+, Ti3+, Zr4+, Sc3+, Zn2+, Mg2+, Fe2+, Mn2+), e T a catioes em coordenacao tetrahedrica (Si4+, Al3+, Fe3+). As piroxenas com estrutura monoclinica sao designadas de clinopiroxenes. A estabilidade das clinopyroxenes num espectro de composicoes quimicas amplo, em conjugacao com a possibilidade de ajustar as suas propriedades fisicas e quimicas e a durabilidade quimica, tem gerado um interesse mundial devido a suas aplicacoes em ciencia e tecnologia de materiais. Este trabalho trata do desenvolvimento de vidros e de vitro-cerâmicos baseadas de clinopiroxenas para aplicacoes funcionais. O estudo teve objectivos cientificos e tecnologicos; nomeadamente, adquirir conhecimentos fundamentais sobre a formacao de fases cristalinas e solucoes solidas em determinados sistemas vitro-cerâmicos, e avaliar a viabilidade de aplicacao dos novos materiais em diferentes areas tecnologicas, com especial enfase sobre a selagem em celulas de combustivel de oxido solido (SOFC). Com este intuito, prepararam-se varios vidros e materiais vitro-cerâmicos ao longo das juntas Enstatite (MgSiO3) - diopsidio (CaMgSi2O6) e diopsidio (CaMgSi2O6) - Ca - Tschermak (CaAlSi2O6), os quais foram caracterizados atraves de um vasto leque de tecnicas. Todos os vidros foram preparados por fusao-arrefecimento enquanto os vitro-cerâmicos foram obtidos quer por sinterizacao e cristalizacao de fritas, quer por nucleacao e cristalizacao de vidros monoliticos. Estudaram-se ainda os efeitos de varias substituicoes ionicas em composicoes de

El uso de la neuromodulación para el tratamiento del temblor

PubMed Central

Bendersky, Damián; Ajler, Pablo; Yampolsky, Claudio

2014-01-01

Introducción: El temblor puede ser un desorden incapacitante y el tratamiento de primera línea para estos pacientes es farmacológico. Sin embargo, este tratamiento puede llevar a una reducción satisfactoria del temblor en sólo el 50% de los pacientes con temblor esencial. La talamotomía era el tratamiento de elección para el temblor refractario al tratamiento médico hasta que comenzó a utilizarse la estimulación cerebral profunda (ECP) del núcleo ventral intermedio (Vim) del tálamo. En la actualidad, raramente se realiza la talamotomía. Métodos: Este artículo es una revisión no sistemática de las indicaciones, resultados, parámetros de programación y técnica quirúrgica de la ECP del Vim para el tratamiento del temblor. Resultados: Aunque los resultados clínicos son similares usando la talamotomía o la ECP del Vim, la primera causa más efectos adversos que la última. Además, la ECP puede ser usada bilateralmente, mientras que la talamotomía tiene un alto riesgo de causar disartria cuando se realiza de ambos lados. La ECP del Vim logró una adecuada mejoría del temblor en varias series de pacientes con temblor causado por temblor esencial, enfermedad de Parkinson o esclerosis múltiple. Además del Vim, hay otros blancos que están siendo usados por varios autores, tales como la zona incerta y las radiaciones prelemniscales. Conclusión: La ECP del Vim es un tratamiento útil para el temblor incapacitante refractario al tratamiento médico. Es esencial realizar una precisa selección de pacientes, así como utilizar una técnica quirúrgica correcta. Aún se desconoce el mejor blanco estereotáctico para el temblor, aunque el Vim es el más usado. PMID:25165613

Desarrollo de un instrumento para medir percepciones sobre el contexto de construccion del conocimiento cientifico de estudiantes universitarios de nuevo ingreso

NASA Astrophysics Data System (ADS)

Garcia-Ramirez, Jaime Antonio

En esta investigacion, se desarrollo un instrumento que permite medir percepciones relacionadas al contexto de constriccion del conocimiento cientifico. Se examinaron instrumentos existentes y se encontro que el VOSTS (Views on science, technology, and society), instrumento desarrollado empiricamente en Canada por Aikenhead, Ryan y Fleming, podia traducirse y validarse en el contexto cultural puertorriqueno. El instrumento es extenso, consta de 113 reactivos, cada uno con una premisa basica relacionada a la tematica ciencia, tecnologia y sociedad y un numero de alternativas relacionadas a la premisa que oscila entre siete y trece. Se delimito su utilizacion a los quince reactivos identificados por los autores como relacionados a la construccion social del conocimiento cientifico. Metodologicamente, se procedio a utilizar el modelo de adaptacion intercultural, que permite que el instrumento desarrollado satisfaga las dimensiones de equivalencia semantica, de contenido, tecnica, de criterio y conceptual, atemperado asi al instrumento original. Se cumplio con este proposito mediante la traduccion de la version original en ingles al espanol y viceversa. Se utilizaron comites para examinar la traduccion y la retro-traduccion del instrumento. Se realizo una prueba piloto con estudiantes universitarios de nuevo ingreso, utilizando el instrumento traducido para asegurar su intelegibilidad. La confiabilidad del instrumento se determino mediante la intervencion de un panel de expertos quienes clasificaron las distintas posiciones dentro de cada reactivo en: realista, con merito e ingenua; se transformaron estas opciones en valores numericos lo que permitio establecer una escala Likert para cada una. Se suministro el instrumento a una muestra de estudiantes universitarios de nuevo ingreso con caracteristicas similares a las de la poblacion puertorriquena en cuanto a ejecucion en las pruebas de aptitud verbal y matematica del College Board. Los resultados de sus contestaciones

The Gd-Co-Al system at 870/1070 K as a representative of the rare earth-Co-Al family and new rare-earth cobalt aluminides: Crystal structure and magnetic properties

NASA Astrophysics Data System (ADS)

Morozkin, A. V.; Garshev, A. V.; Knotko, A. V.; Yapaskurt, V. O.; Mozharivskyj, Y.; Yuan, Fang; Yao, Jinlei; Nirmala, R.; Quezado, S.; Malik, S. K.

2018-05-01

The Gd-Co-Al system has been investigated at 870/1070 K by X-ray and elemental EDS analyses. The existence of the known compounds Gd2Co3Al9 (Y2Co3Ga9-type), Gd3Co4.5Al11.5 (Gd3Co4.6Al11) (Gd3Ru4Al12-type), Gd3Co6-7.4Al3-1.6 (CeNi3-type), GdCo1.15-0.65Al0.85-1.35 (MgZn2-type), Gd2Co2Al (Mo2NiB2-type) and Gd3Co3.5-3.25Al0.5-0.75 (W3CoB3-type) has been confirmed at 870/1070 K. Structure types have been determined for Gd2Co6Al19 (U2Co6Al19-type), Gd7Co6Al7 (Pr7Co6Al7-type), Gd6Co2-2.21Al1-0.79 (Ho6Co2Ga-type) and Gd14Co3.2Al2.8 (Gd14Co2.58Al3.42 at 970 K) (Lu14Co3In3-type). The structures of Gd6Co2Al, Gd6Co2.21Al0.79 and Gd14Co2.58Al3.42 flux-grown at 970 K have been refined from the single crystal X-ray diffraction data. Additionally, new ternary compounds Gd2Co5.7-5.3Al1.3-1.7 (Er2Co7-type) and Gd58Co20Al22 (unknown type structure) have been identified. Quasi-binary solid solutions were detected for Gd2Co17, GdCo5, Gd2Co7, GdCo3, GdCo2 and GdAl2 at 870/1070 K, while no appreciable solubility was observed for the other binary compounds in the Gd-Co-Al system. Magnetic properties of the Gd2Co3Al9, Gd3Co4.6Al11, Gd7Co6Al7, Gd6Co2.2Al0.8 and Gd14Co2.58Al3.42 compounds have been studied and are presented in this work. Gd6Co2.2Al0.8, Gd3Co4.6Al11, Gd7Co6Al7 and Gd14Co2.58Al3.42 order ferromagnetically, while Gd2Co3Al9 displays antiferromagnetic transition. Additionally, {Y, Sm, Tb - Tm}2Co6Al19 (U2Co6Al19-type), Yb2Co3Al9 (Y2Co3Ga9-type), {Y, Sm, Tm, Yb}3Co4.6Al11 (Gd3Ru4Al12-type) and Tb7Co6Al7 (Pr7Co6Al7-type) compounds have been synthesized and investigated.

Econometric Models of U.S. Navy Career Petty Officer Retention.

DTIC Science & Technology

1981-06-01

PF AD-AL04 076 NAVAL POSTGRADUATE SCHOOL MONTEREY CA F/6 5/9 ECONO ETRIC MODELS OF U.S. NAVY CAREER PETTY OFFICER RETENTION.(Ul JUN 81 J J B PKO...THESIS D . ECONOMETRIC MODELS OF U. S. NAVY CAREER PETTY OFFICER RETENTION SML Vby John Joseph Bepko III June 1981 Thesis Advisor: George W. Thomas...DOCUMENTATION PACE 33703 coTu~rwc oEm 0419PsR 01N1911VT*48~ &GM01 1𔃻. 411CIP1SIMYS CATALOG IulmSIS Econometric Models of U. S. Navy Career Petty 1’ t h s s j

Tank characterization report for single-shell tank 241-U-110. Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, T.M.; Jensen, L.

1993-09-01

Tank 241-U-110 (U-110) is a Hanford Site waste tank that was ;most recently sampled in November and December 1989. Analysis of the samples obtained from tank U-110 was conducted to support the characterization of the contents of this tank and to support Hanford Federal Facility Agreement and Consent Order milestone M-10-00 (Ecology, et al. 1992). Because of incomplete recovery of the waste during sampling, there may be bias in the results of this characterization report.

Effect of Al(OH)3 on the sintering of UO2-Gd2O3 fuel pellets with addition of U3O8 from recycle

NASA Astrophysics Data System (ADS)

dos Santos, Lauro Roberto; Durazzo, Michelangelo; Urano de Carvalho, Elita Fontenele; Riella, Humberto Gracher

2017-09-01

The incorporation of gadolinium as burnable poison directly into nuclear fuel is important for reactivity compensation, which enables longer fuel cycles. The function of the burnable poison fuel is to control the neutron population in the reactor core during its startup and the beginning of the fuel burning cycle to extend the use of the fuel. The implementation of UO2-Gd2O3 poisoned fuel in Brazil has been proposed according to the future requirements established for the Angra-2 nuclear power plant. The UO2 powder used is produced from the Ammonium Uranyl Carbonate (AUC). The incorporation of Gd2O3 powder directly into the AUC-derived UO2 powder by dry mechanical blending is the most attractive process, because of its simplicity. Nevertheless, processing by this method leads to difficulties while obtaining sintered pellets with the minimum required density. The cause of the low densities is the bad sintering behavior of the UO2-Gd2O3 mixed fuel, which shows a blockage in the sintering process that hinders the densification. This effect has been overcome by microdoping of the fuel with small quantities of aluminum. The process for manufacturing the fuel inevitably generates uranium-rich scraps from various sources. This residue is reincorporated into the production process in the form of U3O8 powder additions. The addition of U3O8 also hinders densification in sintering. This study was carried out to investigate the influence of both aluminum and U3O8 additives on the density of fuel pellets after sintering. As the effects of these additives are counterposed, this work studied the combined effect thereof, seeking to find an applicable composition for the production process. The experimental results demonstrated the effectiveness of aluminum, in the form of Al(OH)3, as an additive to promote increase in the densification of the (U,Gd)O2 pellets during sintering, even with high additions of U3O8 recycled from the manufacturing process.

43. U.S. NITRATE PLANT UNDER CONSTRUCTION, STEEL BEING ERECTED FOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. U.S. NITRATE PLANT UNDER CONSTRUCTION, STEEL BEING ERECTED FOR THE MACHINE SHOP, FEBRUARY 28, 1918. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Electronic properties of 3R-CuAlO2 under pressure: Three theoretical approaches

NASA Astrophysics Data System (ADS)

Christensen, N. E.; Svane, A.; Laskowski, R.; Palanivel, B.; Modak, P.; Chantis, A. N.; van Schilfgaarde, M.; Kotani, T.

2010-01-01

The pressure variation in the structural parameters, u and c/a , of the delafossite CuAlO2 is calculated within the local-density approximation (LDA). Further, the electronic structures as obtained by different approximations are compared: LDA, LDA+U , and a recently developed “quasiparticle self-consistent GW ” (QSGW) approximation. The structural parameters obtained by the LDA agree very well with experiments but, as expected, gaps in the formal band structure are underestimated as compared to optical experiments. The (in LDA too high lying) Cu3d states can be down shifted by LDA+U . The magnitude of the electric field gradient (EFG) as obtained within the LDA is far too small. It can be “fitted” to experiments in LDA+U but a simultaneous adjustment of the EFG and the gap cannot be obtained with a single U value. QSGW yields reasonable values for both quantities. LDA and QSGW yield significantly different values for some of the band-gap deformation potentials but calculations within both approximations predict that 3R-CuAlO2 remains an indirect-gap semiconductor at all pressures in its stability range 0-36 GPa, although the smallest direct gap has a negative pressure coefficient.

42. U.S. NITRATE PLANT UNDER CONSTRUCTION, STEEL BEING ERECTED FOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. U.S. NITRATE PLANT UNDER CONSTRUCTION, STEEL BEING ERECTED FOR THE CARBIDE MILL ROOM, APRIL 23, 1918. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Sharpening the U-Th Chronometer: Progress and Outlook

NASA Astrophysics Data System (ADS)

McLean, N. M.; Condon, D. J.; Henderson, G. M.; Richards, D. A.; Noble, S.; Mason, A.

2013-12-01

Uranium is incorporated into a variety of natural materials when they form, including carbonates like speleothems and corals. The two most abundant naturally occurring uranium isotopes, 238U and 235U, decay to 206Pb and 207Pb over long timescales with half-lives of 4.5 and 0.7 billion years respectively, but transition through several intermediate daughter isotopes with shorter half-lives first. Fractionation between these daughter isotopes, including 234U, 230Th, and 231Pa, and their parent isotopes, followed by their time-dependent return to secular equilibrium over the course of up to ~800 kyr, forms the basis for U-series geochronology, and allows speleothems and corals to be precisely dated. These carbonates often additionally incorporate chemical and isotopic signatures (e.g., trace elements, δ18O and δ13C) from the environment in which they form, and thus are some of the best dated paleoclimate archives, offering clues about past and future conditions for life on Earth. Over the past decade, the analytical precision of U-series isotope measurements has improved dramatically, largely due to the steadily increasing sensitivity of multiple-collector inductively coupled plasma mass spectrometry (MC-ICP-MS). Analytical uncertainties in U-Th dates now approach or are better than 0.1% (2σ), for instance ×100 years for a speleothem or coral that is 130 kyr old (Cheng et al., 2013). However, the accuracy of U-series dates also depends on the accuracy of tracer calibrations, reference solutions and data reduction protocols, which has not kept pace in many laboratories. This means that dates measured in different labs, while impressively precise, may not be directly comparable. To address issues of inter-laboratory bias and improve the accuracy and inter-comparability of U-Th dates, we have instigated work in three related directions. First, we report on the mixing of three synthetic U-Th age solutions, created by combining high-purity mono-isotopic solutions to

The United Arab Emirates (UAE): Issues for U.S. Policy

DTIC Science & Technology

2010-12-07

tallest building, on January 4, 2010. Dubai metro has begun operations and is expanding service. Burj al Arab hotel in Dubai bills itself as “world’s...CRS Report for Congress Prepared for Members and Committees of Congress The United Arab Emirates (UAE): Issues for U.S. Policy Kenneth...3. DATES COVERED 00-00-2010 to 00-00-2010 4. TITLE AND SUBTITLE The United Arab Emirates (UAE): Issues for U.S. Policy 5a. CONTRACT NUMBER

The United Arab Emirates (UAE): Issues for U.S. Policy

DTIC Science & Technology

2010-06-23

operations and is expanding service. Burj al Arab hotel in Dubai bills itself as “world’s only 7-star hotel.” UAE participating in Gulf country-wide...CRS Report for Congress Prepared for Members and Committees of Congress The United Arab Emirates (UAE): Issues for U.S. Policy Kenneth...DATES COVERED 00-00-2010 to 00-00-2010 4. TITLE AND SUBTITLE The United Arab Emirates (UAE): Issues for U.S. Policy 5a. CONTRACT NUMBER 5b

Microstructural Characterization of a Mg Matrix U-Mo Dispersion Fuel Plate Irradiated in the Advanced Test Reactor to High Fission Density: SEM Results

NASA Astrophysics Data System (ADS)

Keiser, Dennis D.; Jue, Jan-Fong; Miller, Brandon D.; Gan, Jian; Robinson, Adam B.; Medvedev, Pavel G.; Madden, James W.; Moore, Glenn A.

2016-06-01

Low-enriched (U-235 <20 pct) U-Mo dispersion fuel is being developed for use in research and test reactors. In most cases, fuel plates with Al or Al-Si alloy matrices have been tested in the Advanced Test Reactor to support this development. In addition, fuel plates with Mg as the matrix have also been tested. The benefit of using Mg as the matrix is that it potentially will not chemically interact with the U-Mo fuel particles during fabrication or irradiation, whereas with Al and Al-Si alloys such interactions will occur. Fuel plate R9R010 is a Mg matrix fuel plate that was aggressively irradiated in ATR. This fuel plate was irradiated as part of the RERTR-8 experiment at high temperature, high fission rate, and high power, up to high fission density. This paper describes the results of the scanning electron microscopy (SEM) analysis of an irradiated fuel plate using polished samples and those produced with a focused ion beam. A follow-up paper will discuss the results of transmission electron microscopy (TEM) analysis. Using SEM, it was observed that even at very aggressive irradiation conditions, negligible chemical interaction occurred between the irradiated U-7Mo fuel particles and Mg matrix; no interconnection of fission gas bubbles from fuel particle to fuel particle was observed; the interconnected fission gas bubbles that were observed in the irradiated U-7Mo particles resulted in some transport of solid fission products to the U-7Mo/Mg interface; the presence of microstructural pathways in some U-9.1 Mo particles that could allow for transport of fission gases did not result in the apparent presence of large porosity at the U-7Mo/Mg interface; and, the Mg-Al interaction layers that were present at the Mg matrix/Al 6061 cladding interface exhibited good radiation stability, i.e. no large pores.

AlGaInN laser diode technology for free-space telecom applications

NASA Astrophysics Data System (ADS)

Najda, S. P.; Perlin, P.; Suski, T.; Marona, L.; Boćkowski, M.; Leszczyński, M.; Wisniewski, P.; Czernecki, R.; Kucharski, R.; Targowski, G.; Watson, S.; Kelly, A. E.; Watson, M. A.; Blanchard, P.; White, H.

2015-03-01

The AlGaInN material system allows for laser diodes to be fabricated over a very wide range of wavelengths from u.v., ~380nm, to the visible ~530nm, by tuning the indium content of the laser GaInN quantum well. We consider the suitability of AlGaInN laser diode technology for free space laser communication, both airborne links and underwater telecom applications, mainly for defense and oil and gas industries.

U.S. Border Patrol OCONUS: Possible Contributions to the Whole of Government Approach to Stability Operations

DTIC Science & Technology

2010-06-11

Force–Rural Area Police Patrol Unit (Unidad Móvil Policial Para Reas Rurales) also known as Los Leopardos (the Leopards ). USBP U.S. Border Patrol...99Ibid. 38 Antinarcotics Force--Rural Area Police Patrol Unit (Unidad Móvil Policial Para Reas Rurales) also known as Los Leopardos (the Leopards ). The...training or preparation time for this mission. Upon arrival he found that the inclement cold weather included snow , sleet, ice, and frigid cold

47. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING NORTH AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

47. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING NORTH AT THE AUTOCLAVE BUILDING UNDER CONSTRUCTION, APRIL 23, 1918. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

The <u>Be>rkeley <u>A>tmospheric <u>C>O2 <u>O>bservation <u>N>etwork (BEACON): Measuring Greenhouse Gases and Criteria Pollutants within the Urban Dome

NASA Astrophysics Data System (ADS)

Teige, V. E.; Weichsel, K.; Hooker, A.; Wooldridge, P. J.; Cohen, R. C.

2012-12-01

Efforts to curb greenhouse gas emissions, while global in their impacts, often focus on local and regional scales for execution and are dependent on the actions of communities and individuals. Evaluating the effectiveness of local policies requires observations with much higher spatial resolution than are currently available---kilometer scale. The <u>Be>rkeley <u>A>tmospheric <u>C>O2 <u>O>bservation <u>N>etwork (BEACON):, launched at the end of 2011, aims to provide measurements of urban-scale concentrations of CO2, temperature, pressure, relative humidity, O3, CO, and NO2 with sufficient spatial and temporal resolution to characterize the sources of CO2 within cities. Our initial deployment in Oakland, California uses ~40 sensor packages at a roughly 2 km spacing throughout the city. We will present an initial analysis of the vertical gradients and other spatial patterns observed to date.

Etnografía acelerada para transformar normas sociales sobre género y sexualidad en hombres puertorriqueños heterosexuales1,2

PubMed Central

Ortiz-Torres, Blanca; Rivera-Ortiz, Rafael J.; Mendoza, Sigrid

2014-01-01

Resumen La construcción de roles de género dominantes contribuyen al riesgo de contraer VIH, y por tal razón se ha urgido a que se integren las normas sociales relativas al género en las intervenciones preventivas del VIH. Este estudio pretende adaptar y desarrollar una intervención que facilite la transformación de normas sociales del género y de prácticas sexuales en hombres puertorriqueños. La intervención propone transformar normas sociales relacionadas al género y sexualidad en barras comunitarias utilizando el modelo de líderes de opinión. Luego de ser elegidos/as, los/as líderes de opinión diseminan mensajes integrando la importancia de relaciones equitativas entre parejas para la prevención del VIH. La primera fase de esta intervención es discutida en este artículo, la cual incluye un proceso de etnografía acelerada para identificar los escenarios comunitarios en los que podemos desarrollar esta intervención y permitirnos entender la cultura de las barras comunitarias. A partir de las observaciones etnográficas, pudimos: desarrollar un protocolo de seguridad para realizar las observaciones, desarrollar un perfil de la cultura de las barras, elegir las barras a participar en las dos condiciones del estudio y adaptar los instrumentos de la intervención para que respondieran a la particularidad de los/as participantes. PMID:25530828

Determination of elemental impurities and U and O isotopic compositions with a view to identify the geographical and industrial origins of uranium ore concentrates

NASA Astrophysics Data System (ADS)

Salaun, A.; Hubert, A.; Pointurier, F.; Aupiais, J.; Pili, E.; Richon, P.; Fauré, A.; Diallo, S.

2012-12-01

First events of illicit trafficking of nuclear and radiological materials occurred 50 years ago. Nuclear forensics expertise are aiming at determining the use of seized material, its industrial history and provenance (geographical area, place of production or processing), at assisting in the identification and dismantling of illicit trafficking networks. This information is also valuable in the context of inspections of declared facilities to verify the consistency of operator's declaration. Several characteristics can be used to determine the origin of uranium ore concentrates such as trace elemental impurity patterns (Keegan et al., 2008 ; Varga et al., 2010a, 2010b) or uranium, oxygen and lead isotopic compositions (Tamborini et al., 2002a, 2002b ; Wallenius et al., 2006; Varga et al., 2009). We developed analytical procedures for measuring the isotopic compositions of uranium (234U/238U and 235U/238U) and oxygen (18O/16O) and levels of elemental impurities (e.g. REE, Th) from very small amounts of uranium ore concentrates (or yellow cakes). Micrometer particles and few milligrams of material are used for oxygen isotope measurements and REE determination, respectively. Reference materials were analyzed by mass spectrometry (TIMS, SF-ICP-MS and SIMS) to validate testing protocols. Finally, materials of unknown origin were analyzed to highlight significant differences and determine whether these differences allow identifying the origin of these ore concentrates. References: Keegan, E., et al. (2008). Applied Geochemistry 23, 765-777. Tamborini, G., et al. (2002a). Analytical Chemistry 74, 6098-6101. Tamborini, G., et al. (2002b). Microchimica Acta 139, 185-188. Varga, Z., et al. (2009). Analytical Chemistry 81, 8327-8334. Varga, Z., et al. (2010a). Talanta 80, 1744-1749. Varga, Z., et al. (2010b). Radiochimica Acta 98, 771-778 Wallenius, M., et al. (2006). Forensic Science International 156, 55-62.

Extensión del Formalismo de Orbitales de Defecto Cuántico al tratamiento del efecto Stark (SQDO).

NASA Astrophysics Data System (ADS)

Menéndez, J. M.; Martín, I.; Velasco, A. M.

El estudio experimental de las interacciones de átomos Rydberg altamente excitados con campos eléctricos ha experimentado un creciente interés durante las dos últimas décadas debido, en gran medida, al desarrollo de nuevas técnicas para crear y estudiar átomos Rydberg en el laboratorio. Acompañando a estas nuevas técnicas experimentales, es necesario el desarrollo de modelos teóricos que nos permitan contrastar sus medidas y conocer mejor los fundamentos de los mismos. Desde el punto de vista teórico el conocimiento del desdoblamiento de los niveles energéticos de un átomo en función de la magnitud del campo eléctrico aplicado (lo que se conoce como mapa Stark) es el mejor punto de partida para la descripción del sistema y un prerrequisito fundamental para el cálculo de distintas propiedades atómicas en presencia del campo eléctrico tales como intensidades de transición, umbrales de ionización de campo eléctrico, tiempos de vida, posición y anchura de cruces evitados, etc. En este trabajo presentamos la adaptación del método de orbitales de defecto cuántico [1,2,3] al tratamiento del efecto Stark (SQDO) [4] y su aplicación al cálculo de los desdoblamientos energéticos y fuerzas de oscilador de estados Rydberg en los átomos de Li, Na y K. El propósito de este estudio es, por un lado, desarrollar métodos fiables para la determinación de propiedades atómicas en presencia de campos eléctricos y, por otro, mostrar la fiabilidad de las funciones de onda QDO en la descripción del efecto Stark en sistemas atómicos.

Distribution of 26Al in the CR chondrite chondrule-forming region of the protoplanetary disk

NASA Astrophysics Data System (ADS)

Schrader, Devin L.; Nagashima, Kazuhide; Krot, Alexander N.; Ogliore, Ryan C.; Yin, Qing-Zhu; Amelin, Yuri; Stirling, Claudine H.; Kaltenbach, Angela

2017-03-01

trends with major and minor element or O-isotope compositions between these populations. The weighted mean (26Al/27Al)0 of 22 CR chondrules measured is (1.8 ± 0.3) × 10-6. An apparent agreement between the 26Al-26Mg ages (using weighted mean value) and the revised (using 238U/235U ratio for bulk CR chondrites of 137.7789 ± 0.0085) 207Pb-206Pb age of a set of chondrules from CR chondrites (Amelin et al., 2002, Science297, 1678) is consistent with the initial 26Al/27Al ratio in the CR chondrite chondrule-forming region at the canonical level (∼5.2 × 10-5), allowing the use of 26Al-26Mg systematics as a chronometer for CR chondrules. To prove chronological significance of 26Al for CR chondrules, measurements of Al-Mg and U-Pb isotope systematics on individual chondrules are required. The presence of several generations among CR chondrules indicates some chondrules that accreted into the CR chondrite parent asteroid avoided melting by later chondrule-forming events, suggesting chondrule-forming processes may have occurred on relatively limited spatial scales. Accretion of the CR chondrite parent body occurred at >4.0-0.3+0.5 Ma after the formation of CAIs with the canonical 26Al/27Al ratio, although rapid accretion after formation of the major population of CR chondrules is not required by our data.

The Jericho Option: Al-Qa'ida and Attacks on Critical Infrastructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ackerman, G; Blair, C; Bale, J

There is no doubt that al-Qaida and its affiliates have displayed, and continue to display, an acute interest in attacking targets that are considered to be important components of the infrastructure of the United States. What has not thus far been carried out, however, is an in-depth examination of the basic nature, historical evolution, and present scope of the organization's objectives that might help government personnel develop sound policy recommendations and analytical indicators to assist in detecting and interdicting plots of this nature. This study was completed with the financial support of the Lawrence Livermore National Laboratory, through a projectmore » sponsored by the U.S. Department of Homeland Security, Science and Technology Directorate. It is specifically intended to increase counterterrorism analysts understanding of certain features of al-Qaida's strategy and operations in order to facilitate the anticipation and prevention of attacks directed against our most critical infrastructures. The procedure adopted herein has involved consulting a wide variety of source materials that bear on the topic, ranging from sacred religious texts and historical accounts to al-Qaida-linked materials and the firsthand testimony of captured members of the group. It has also intentionally combined multiple approaches, including exploring the more esoteric religion-historical referents that have served to influence al-Qaida's behavior, providing a strategic analysis of its objectives and targeting rationales, closely examining the statements and writings of al-Qaida leaders and spokesmen (in part on the basis of material translated from primary sources), offering a descriptive analysis of its past global attack patterns, and producing concise but nonetheless in-depth case studies of its previous ''infrastructural'' attacks on U.S. soil. The analyses contained herein tend to support the preliminary assessment made by some of the authors in an earlier report

A modern framework for the interpretation of 238U/235U in studies of ancient ocean redox

NASA Astrophysics Data System (ADS)

Andersen, M. B.; Romaniello, S.; Vance, D.; Little, S. H.; Herdman, R.; Lyons, T. W.

2014-08-01

The abundance and isotope composition of redox sensitive elements in ancient sediments are increasingly used to understand the past ocean's geochemical state and the oxygenation history of the Earth. The redox transition of uranium (U) from soluble U+6 to relatively insoluble U+4 and its subsequent incorporation into reduced sediments has been used to deduce the redox state of the oceans in the past. Furthermore, recent analytical improvements have revealed significant 238U/235U fractionation during this redox transition, offering the potential for U isotopes to act as a redox proxy. However, the development of U isotopes as a geochemical tracer requires that U isotope systematics associated with redox changes, are well-characterized. This study focuses on U isotopes in recent sediments from the two largest modern anoxic ocean basins, the Black Sea and the Cariaco Basin, with the aim of advancing our understanding of the U isotope systematics in reducing marine environments. These anoxic sediments have high U accumulation rates and high 238U/235U ratios relative to seawater, in general agreement with a process that accumulates reduced U with a heavy isotopic composition. Using Al and Ca concentrations to correct for detrital and biogenic carbonate-bound U, we estimate the reduced authigenic U accumulated in the sediments and its 238U/235U. These results highlight the importance of isotopic mass balance constraints during diffusive transport and reaction of U from seawater and through pore-water, affecting the observed 238U/235U in sediments. Using these constraints, the average percentages of U depletion from top to bottom of the water column can be estimated, assuming batch-removal of U into anoxic sediments in a restricted basin. Using this framework, 238U/235U in modern anoxic sediments from the Black Sea imply U depletions in the water column of ∼30%, which is close to the observed ∼40% U depletion in the modern Black Sea water column at these depths

AlGaInN laser diode technology and systems for defence and security applications

NASA Astrophysics Data System (ADS)

Najda, Stephen P.; Perlin, Piotr; Suski, Tadek; Marona, Lucja; Boćkowski, Mike; Leszczyński, Mike; Wisniewski, Przemek; Czernecki, Robert; Kucharski, Robert; Targowski, Grzegorz; Watson, Scott; Kelly, Antony E.

2015-05-01

The latest developments in AlGaInN laser diode technology are reviewed for defence and security applications such as underwater communications. The AlGaInN material system allows for laser diodes to be fabricated over a very wide range of wavelengths from u.v., ~380nm, to the visible ~530nm, by tuning the indium content of the laser GaInN quantum well. Thus AlGaInN laser diode technology is a key enabler for the development of new disruptive system level applications in displays, telecom, defence and other industries.

Effect of aluminum treatment on proteomes of radicles of seeds derived from Al-treated tomato plants

USDA-ARS?s Scientific Manuscript database

Aluminum (Al) toxicity is a major constraint to plant growth and crop yield in acid soils. Tomato cultivars are especially susceptible to excessive A1 3+ accumulated in the root zone. In this study, tomato plants were grown in a hydroponic culture system supplemented with 50 uM AlK(SO4)2. Seeds harv...

Early accretion of protoplanets inferred from a reduced inner solar system 26Al inventory

PubMed Central

Schiller, Martin; Connelly, James N.; Glad, Aslaug C.; Mikouchi, Takashi; Bizzarro, Martin

2016-01-01

The mechanisms and timescales of accretion of 10–1000 km sized planetesimals, the building blocks of planets, are not yet well understood. With planetesimal melting predominantly driven by the decay of the short-lived radionuclide 26Al (26Al→26Mg; t1/2 = 0.73 Ma), its initial abundance determines the permissible timeframe of planetesimal-scale melting and its subsequent cooling history. Currently, precise knowledge about the initial 26Al abundance [(26Al/27Al)0] exists only for the oldest known solids, calcium aluminum-rich inclusions (CAIs) – the so-called canonical value. We have determined the 26Al/27Al of three angrite meteorites, D’Orbigny, Sahara 99555 and NWA 1670, at their time of crystallization, which corresponds to (3.98 ± 0.15)×10−7, (3.64 ± 0.18)×10−7, and (5.92 ± 0.59)×10−7, respectively. Combined with a newly determined absolute U-corrected Pb–Pb age for NWA 1670 of 4564.39 ± 0.24 Ma and published U-corrected Pb–Pb ages for the other two angrites, this allows us to calculate an initial (26Al/27Al)0 of (1.33−0.18+0.21)×10−5 for the angrite parent body (APB) precursor material at the time of CAI formation, a value four times lower than the accepted canonical value of 5.25 × 10−5. Based on their similar 54Cr/52Cr ratios, most inner solar system materials likely accreted from material containing a similar 26Al/27Al ratio as the APB precursor at the time of CAI formation. To satisfy the abundant evidence for widespread planetesimal differentiation, the subcanonical 26Al budget requires that differentiated planetesimals, and hence protoplanets, accreted rapidly within 0.25 ± 0.15 Ma of the formation of canonical CAIs. PMID:27429474

Modelizacion, control e implementacion de un procesador energetico paralelo para aplicacion en sistemas multisalida

NASA Astrophysics Data System (ADS)

Ferreres Sabater, Agustin

Cualquier sistema electronico que incluya un procesado o tratamiento de la senal, y ademas, algun tipo de actuador mecanico generalmente necesita, como minimo, dos tensiones diferentes de alimentacion. Excluyendo los sistemas de alimentacion distribuida, la solucion tecnica mas utilizada para proporcionar dos o mas tensiones consiste en las fuentes de alimentacion multisalida. En una fuente de alimentacion multisalida los diferentes circuitos que conforman cada salida comparten un mismo transformador de potencia optimizando coste, masa, y volumen. Las ventajas obtenidas con este procedimiento tienen en su contra el efecto que sobre cada salida individual provocan las demas en su conjunto debido, principalmente, a los efectos de los elementos parasitos de los componentes. Un cambio de carga en una de las salidas produce un transitorio que es visto por todas las demas como un efecto de impedancia cruzada, y al final del transitorio, la tension de cada salida es diferente respecto a la que tenian antes del transitorio. Este ultimo resultado se conoce como regulacion cruzada. La disminucion de los efectos de la regulacion cruzada ha sido objeto de estudio durante los ultimos anos. El objetivo ha sido el desarrollo de distintas estrategias que permiten, desde disminuir los efectos de la regulacion cruzada hasta los niveles deseables, a eliminarla completamente. El resultado final suele suponer una penalizacion sobre el diseno del sistema directamente proporcional al grado de regulacion a conseguir en las distintas salidas. Entre las soluciones propuestas para eliminar la regulacion cruzada las tecnicas de post-regulacion se han consolidado como la opcion mas aceptada ya que, pueden aplicarse a cualquier convertidor y no suponen ninguna complejidad adicional a la hora de plantear el diseno. En esta Tesis Doctoral se abordara el estudio de la tecnica conocida como postregulacion mediante transformador controlado, que si bien se ha empleado en convertidores resonantes, su

Sea-level history and tectonic uplift during the last-interglacial period (LIG): Inferred from the Bab al-Mandab coral reef terraces, southern Red Sea

NASA Astrophysics Data System (ADS)

Al-Mikhlafi, Ahmed Saif; Edwards, Lawrence R.; Cheng, Hai

2018-02-01

Results of U-series dating of late Pleistocene raised coral reef terraces from the Bab al-Mandab area, define two distinct groups: (1) well-preserved aragonitic fossil corals recorded from the Al-Hajaja terrace (Tr3) yield ages for last-interglacial period (LIG); and (2) calcitic fossil corals recovered from Perim Island terrace (Tr1) show varying degrees of U-series open system behavior and yield coral assemblage ages of LIG and older ages. Fossil corals from Tr1 are recrystallized corals, have anomalously high initial δ234U ranged from (152 ± 2‰ to 287 ± 7‰), corresponding to ages of ∼120 ka and ∼406 ka, respectively. Applying age reliability criteria on the current data suggest majority of the ages cannot be considered reliable and all are suspected for open system behavior associated with U loss/addition that significantly affects the 230Th/U ages. The diagenesis shown by these corals occurred probably due to extensive interaction of fossil corals with freshwater during the wet periods prevailed in southern Arabia coeval with the African monsoon, which led to U loss. Post-depositional U loss suggest (230Th/238U) increase, which shift the U-Th ages to unexpectedly higher levels as it is shown here. Measured elevation at the Al-Hajaja terrace (Tr3) is ∼4 ± 2 m above present sea level (apsl) consistent with eustatic sea level changes and indicates that the Bab al-Mandab area is stable at least since the LIG period. The Perim Island terrace (Tr1) is at elevation of 7 ± 2 m apsl; its reef yields diageneticaly-altered corals of multiple ages and cannot be used for sea level reconstructions.

Geochemistry of basement rocks of incoming plate (Cocos Ridge) from Sites U1381 and 1414, IODP Expeditions 334 and 344

NASA Astrophysics Data System (ADS)

Yan, Q.; Shi, X.

2015-12-01

The drilling sites of IODP 334 and 344 lie in the being subducted part of Cocos Ridge, offshore Costa Rica. Some seamount clusters distributed in the northwest side of the sites. Most scientists accepted that the Cocos ridge is intimately related to the activity of Galapagos plume (e.g., Hoernle et al., 2000, 2004, 2008). In this study we have selected some basaltic samples from U1381A, U1381C and U1414A (IODP 334 and 344) (Harris et al., 2015a, b) to carry out petrogenetic study. Major element compositions show that these basaltic rocks belong to sub-alkaline rocks, which is consistent with previous study on basalts from northern side of Cocos ridge. The characteristics of trace element composition are similar to that of EMORB, and the compositional differences in trace elements among samples reflect the influence of fractional crystallization. Sr-Nd-Pb isotopic compositions of these basaltic rocks show that there exist mantle heterogeneity beneath the Cocos ridge, and they may be the product of mixing between DMM/GSC and EMII. The new data show more enriched source feature than those from Galapagos hotspot (and its tracks) in previous study (Hoernle et al., 2000,2004), and slightly more enriched than those Miocene to Pliocene arc volcanics from Central America (Gazel et al., 2009). Partial melting model show that the parental basalts for these basaltic rocks may be produced by 13 to 28% partial melting of garnet pyroxenite. ReferencesGazel et al., 2009. G-cubed.10, Q02S11, doi:10.1029/2008GC002246.//Harris, R.N., Sakaguchi, A., Petronotis, K., and the Expedition 344 Scientists. 2015a. Input Site U1381. Proceedings of the Integrated Ocean Drilling Program, Volume 344//Harris, R.N., Sakaguchi, A., Petronotis, K., and the Expedition 344 Scientists. 2015b. Input Site U1414.Proceedings of the Integrated Ocean Drilling Program, Volume 344//Hoernle et al., 2000. Geology, 28(5),435-438//Hoernle et al., 2004. Geology, 32,697-700//Hoernle et al., 2008. Nature, 451

U.S. EPA, Pesticide Product Label, , 04/25/1975

EPA Pesticide Factsheets

2011-04-14

... Examint' cpt tOil I,ianl:, (';1 l'l,l'l Ill\\' al1d if allY l''.·idpl1c(' ()f :-'c,U':, 01' i)tlte!'

Development of PRIME for irradiation performance analysis of U-Mo/Al dispersion fuel

NASA Astrophysics Data System (ADS)

Jeong, Gwan Yoon; Kim, Yeon Soo; Jeong, Yong Jin; Park, Jong Man; Sohn, Dong-Seong

2018-04-01

A prediction code for the thermo-mechanical performance of research reactor fuel (PRIME) has been developed with the implementation of developed models to analyze the irradiation behavior of U-Mo dispersion fuel. The code is capable of predicting the two-dimensional thermal and mechanical performance of U-Mo dispersion fuel during irradiation. A finite element method was employed to solve the governing equations for thermal and mechanical equilibria. Temperature- and burnup-dependent material properties of the fuel meat constituents and cladding were used. The numerical solution schemes in PRIME were verified by benchmarking solutions obtained using a commercial finite element analysis program (ABAQUS). The code was validated using irradiation data from RERTR, HAMP-1, and E-FUTURE tests. The measured irradiation data used in the validation were IL thickness, volume fractions of fuel meat constituents for the thermal analysis, and profiles of the plate thickness changes and fuel meat swelling for the mechanical analysis. The prediction results were in good agreement with the measurement data for both thermal and mechanical analyses, confirming the validity of the code.

Conformational explosion: Understanding the complexity of short chain para-dialkylbenzene potential energy surfaces

NASA Astrophysics Data System (ADS)

Mishra, Piyush; Hewett, Daniel M.; Zwier, Timothy S.

2018-05-01

The single-conformation ultraviolet and infrared spectroscopy of three short-chain para-dialkylbenzenes (para-diethylbenzene, para-dipropylbenzene, and para-dibutylbenzene) is reported for the jet-cooled, isolated molecules. The present study builds off previous work on single-chain n-alkylbenzenes, where an anharmonic local mode Hamiltonian method was developed to account for stretch-bend Fermi resonance in the alkyl CH stretch region [D. P. Tabor et al., J. Chem. Phys. 144, 224310 (2016)]. The jet-cooled molecules are interrogated using laser-induced fluorescence (LIF) excitation, fluorescence dip infrared spectroscopy, and dispersed fluorescence. The LIF spectra in the S1 ← S0 origin region show a dramatic increase in the number of resolved transitions with increasing length of the alkyl chains, reflecting an explosion in the number of unique low-energy conformations formed when two independent alkyl chains are present. Since the barriers to isomerization of the alkyl chain are similar in size, this results in an "egg carton" shaped potential energy surface. A combination of electronic frequency shift and alkyl CH stretch infrared spectra is used to generate a consistent set of conformational assignments. Using these experimental techniques in conjunction with computational methods, subsets of origin transitions in the LIF excitation spectrum can be classified into different conformational families. Two conformations are resolved in para-diethylbenzene, seven in para-dipropylbenzene, and about nineteen in para-dibutylbenzene. These chains are largely independent of each other as there are no new single-chain conformations induced by the presence of a second chain. A cursory LIF excitation scan of para-dioctylbenzene shows a broad congested spectrum at frequencies consistent with interactions of alkyl chains with the phenyl π cloud.

Conformational explosion: Understanding the complexity of short chain para-dialkylbenzene potential energy surfaces.

PubMed

Mishra, Piyush; Hewett, Daniel M; Zwier, Timothy S

2018-05-14

The single-conformation ultraviolet and infrared spectroscopy of three short-chain para-dialkylbenzenes (para-diethylbenzene, para-dipropylbenzene, and para-dibutylbenzene) is reported for the jet-cooled, isolated molecules. The present study builds off previous work on single-chain n-alkylbenzenes, where an anharmonic local mode Hamiltonian method was developed to account for stretch-bend Fermi resonance in the alkyl CH stretch region [D. P. Tabor et al., J. Chem. Phys. 144, 224310 (2016)]. The jet-cooled molecules are interrogated using laser-induced fluorescence (LIF) excitation, fluorescence dip infrared spectroscopy, and dispersed fluorescence. The LIF spectra in the S 1 ← S 0 origin region show a dramatic increase in the number of resolved transitions with increasing length of the alkyl chains, reflecting an explosion in the number of unique low-energy conformations formed when two independent alkyl chains are present. Since the barriers to isomerization of the alkyl chain are similar in size, this results in an "egg carton" shaped potential energy surface. A combination of electronic frequency shift and alkyl CH stretch infrared spectra is used to generate a consistent set of conformational assignments. Using these experimental techniques in conjunction with computational methods, subsets of origin transitions in the LIF excitation spectrum can be classified into different conformational families. Two conformations are resolved in para-diethylbenzene, seven in para-dipropylbenzene, and about nineteen in para-dibutylbenzene. These chains are largely independent of each other as there are no new single-chain conformations induced by the presence of a second chain. A cursory LIF excitation scan of para-dioctylbenzene shows a broad congested spectrum at frequencies consistent with interactions of alkyl chains with the phenyl π cloud.

Enhanced Piezoelectric Response of AlN via CrN Alloying

NASA Astrophysics Data System (ADS)

Manna, Sukriti; Talley, Kevin R.; Gorai, Prashun; Mangum, John; Zakutayev, Andriy; Brennecka, Geoff L.; Stevanović, Vladan; Ciobanu, Cristian V.

2018-03-01

Since AlN has emerged as an important piezoelectric material for a wide variety of applications, efforts have been made to increase its piezoelectric response via alloying with transition metals that can substitute for Al in the wurtzite lattice. We report on density functional theory calculations of structure and properties of the Crx Al1 -x N system for Cr concentrations ranging from zero to beyond the wurtzite-rocksalt transition point. By studying the different contributions to the longitudinal piezoelectric coefficient, we propose that the physical origin of the enhanced piezoelectricity in Crx Al1 -x N alloys is the increase of the internal parameter u of the wurtzite structure upon substitution of Al with the larger Cr ions. Among a set of wurtzite-structured materials, we find that Crx Al1 -x N has the most sensitive piezoelectric coefficient with respect to alloying concentration. Based on these results, we propose that Crx Al1 -x N is a viable piezoelectric material whose properties can be tuned via Cr composition. We support this proposal by combinatorial synthesis experiments, which show that Cr can be incorporated in the AlN lattice up to 30% before a detectable transition to rocksalt occurs. At this Cr content, the piezoelectric modulus d33 is approximately 4 times larger than that of pure AlN. This finding, combined with the relative ease of synthesis under nonequilibrium conditions, may position Crx Al1 -x N as a prime piezoelectric material for applications such as resonators and acoustic wave generators.

Enhanced Piezoelectric Response of AlN via CrN Alloying

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manna, Sukriti; Talley, Kevin R.; Gorai, Prashun

2018-03-01

Since AlN has emerged as an important piezoelectric material for a wide variety of applications, efforts have been made to increase its piezoelectric response via alloying with transition metals that can substitute for Al in the wurtzite lattice. We report on density functional theory calculations of structure and properties of the CrxAl1-xN system for Cr concentrations ranging from zero to beyond the wurtzite-rocksalt transition point. By studying the different contributions to the longitudinal piezoelectric coefficient, we propose that the physical origin of the enhanced piezoelectricity in CrxAl1-xN alloys is the increase of the internal parameter u of the wurtzite structuremore » upon substitution of Al with the larger Cr ions. Among a set of wurtzite-structured materials, we find that CrxAl1-xN has the most sensitive piezoelectric coefficient with respect to alloying concentration. Based on these results, we propose that CrxAl1-xN is a viable piezoelectric material whose properties can be tuned via Cr composition. We support this proposal by combinatorial synthesis experiments, which show that Cr can be incorporated in the AlN lattice up to 30% before a detectable transition to rocksalt occurs. At this Cr content, the piezoelectric modulus d33 is approximately 4 times larger than that of pure AlN. This finding, combined with the relative ease of synthesis under nonequilibrium conditions, may position CrxAl1-xN as a prime piezoelectric material for applications such as resonators and acoustic wave generators.« less

Direct Potential Fitting for the a ^3π1u and X ^1Σ^+_g States of {Br_2}

NASA Astrophysics Data System (ADS)

Yukiya, Tokio; Nishimiya, Nobuo; Suzuki, Masao; Le Roy, Robert J.

2012-06-01

Bromine dimer has been studied by many researchers in various wavelength regions. The A ^3π1u and X ^1Σ^+_g states have been well observed using magnetic rotation spectroscopy, by laser-induced fluorescence, by laser absorption, by Fourier transform absorption, and by UV emission. This yields a data set consisting of 16916 transitions in which the observed vibrational levels for the X ^1Σ^+_g and A ^3π1u states span 83% and 99% of the potential well depths, respectively, with the highest observed vibrational level of the A ^3π1u state lying only 2 cm-1 below the dissociation limit.^a In order to provide the most compact and comprehensive description of these data, and the ability to make reliable predictions outside their range, we have chosen to perform a ``direct potential fit'' (DPF), rather than a conventional Dunham-expansion analysis. In particular, accurate analytic potential energy functions for the A ^3π1u and X ^1Σ^+_g states are determined from a combined-isotopologue DPF analysis that also yields the electronic isotope shift, the Ω-doubling radial strength function, and an experimental value for the long-range inverse-power C_5 constant of the A ^3π1u state, as well as centrifugal Born-Oppenheimer Breakdown (BOB) functions for both states. To reveal characteristics of the A ^3π1u state, band constants calculated from these potentials are compared with those determined from a conventional parameter-fitting analysis reported by Coxon. C. D. Boone, PhD Thesis, University of British Columbia (1999). C. Focsa et al., J. Mol. Spectrosc. 200, 104 (2000). D. J. Postell et al., to be published. N. Nishimiya et al., Columbus Meeting, paper WH02 (2005). S. Gerstenkorn et al., J. Physique, 48, 1685 (1987). P. Venkateswarlu et al., J. Mol. Spectrosc. 96, 247 (1982). J. A. Coxon, J. Mol. Spectrosc. 41, 548 (1972).

LaAlO{sub 3} thickness window for electronically controlled magnetism at LaAlO{sub 3}/SrTiO{sub 3} heterointerfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bi, Feng; Huang, Mengchen; Irvin, Patrick

2015-08-24

Complex-oxide heterostructures exhibit rich physical behavior such as emergent conductivity, superconductivity, and magnetism that are intriguing for scientific reasons as well as for potential technological applications. It was recently discovered that in-plane magnetism at the LaAlO{sub 3}/SrTiO{sub 3} (LAO/STO) interface can be electronically controlled at room temperature. Here, we employ magnetic force microscopy to investigate electronically controlled ferromagnetism at the LAO/STO interface with LAO thickness t varied from 4 unit cell (u.c.) to 40 u.c. Magnetic signatures are observed only within a thickness window 8 u.c. ≤ t ≤ 25 u.c. Within this window, the device capacitance corresponds well to the expected geometric value, while for thicknessesmore » outside this window, the capacitance is strongly suppressed. The ability to modulate electronic and magnetic properties of LAO/STO devices depends on the ability to control carrier density, which is in turn constrained by intrinsic tunneling mechanisms.« less

Modeling the net flows of U.S. mutual funds with stochastic catastrophe theory

NASA Astrophysics Data System (ADS)

Clark, A.

2006-04-01

Using the recent work of Hartelman, van der Maas, and Wagenmakers, we demonstrate the use of invariant stochastic catastrophe models in finance for modeling net flows (the difference between purchases and redemptions of fund shares) of U.S. mutual funds. We validate Goetzmann et al. and others' work concerning the importance of sentiment variables on stock fund flows. We also answer some of the questions Goetzmann et al. and Brown et al. pose at the end of their respective papers. We end with possible experiments for experimental economists and sociophysicists.

Comparison of three dimeric 18F-AlF-NOTA-RGD tracers.

PubMed

Guo, Jinxia; Lang, Lixin; Hu, Shuo; Guo, Ning; Zhu, Lei; Sun, Zhongchan; Ma, Ying; Kiesewetter, Dale O; Niu, Gang; Xie, Qingguo; Chen, Xiaoyuan

2014-04-01

RGD peptide-based radiotracers are well established as integrin αvβ3 imaging probes to evaluate tumor angiogenesis or tissue remodeling after ischemia or infarction. In order to optimize the labeling process and pharmacokinetics of the imaging probes, we synthesized three dimeric RGD peptides with or without PEGylation and performed in vivo screening. Radiolabeling was achieved through the reaction of F-18 aluminum-fluoride complex with the cyclic chelator, 1,4,7-triazacyclononane-1,4,7-triacetic acid (NOTA). Three imaging probes were synthesized as (18)F-AlF-NOTA-E[c(RGDfK)]2, (18)F-AlF-NOTA-PEG4-E[c(RGDfK)]2, and (18)F-AlF-NOTA-E[PEG4-c(RGDfk)]2. The receptor binding affinity was determined by competitive cell binding assay, and the stability was evaluated by mouse serum incubation. Tumor uptake and whole body distribution of the three tracers were compared through direct tissue sampling and PET quantification of U87MG tumor-bearing mice. All three compounds remained intact after 120 min incubation with mouse serum. They all had a rapid and relatively high tracer uptake in U87MG tumors with good target-to-background ratios. Compared with the other two tracers, (18)F-AlF-NOTA-E[PEG4-c(RGDfk)]2 had the highest tumor uptake and the lowest accumulation in the liver. The integrin receptor specificity was confirmed by co-injection of unlabeled dimeric RGD peptide. The rapid one-step radiolabeling strategy by the complexation of (18)F-aluminum fluoride with NOTA-peptide conjugates was successfully applied to synthesize three dimeric RGD peptides. Among the three probes developed, (18)F-AlF-NOTA-E[PEG4-c(RGDfk)]2 with relatively low liver uptake and high tumor accumulation appears to be a promising candidate for further translational research.

Atmospheric dust contribution to budget of U-series nuclides in weathering profiles. The Mount Cameroon volcano

NASA Astrophysics Data System (ADS)

Pelt, E.; Chabaux, F. J.; Innocent, C.; Ghaleb, B.

2009-12-01

Analysis of U-series nuclides in weathering profiles is developed today for constraining time scale of soil and weathering profile formation (e.g., Chabaux et al., 2008). These studies require the understanding of U-series nuclides sources and fractionation in weathering systems. For most of these studies the impact of aeolian inputs on U-series nuclides in soils is usually neglected. Here, we propose to discuss such an assumption, i.e., to evaluate the impact of dust deposition on U-series nuclides in soils, by working on present and paleo-soils collected on the Mount Cameroon volcano. Recent Sr, Nd, Pb isotopic analyses performed on these samples have indeed documented significant inputs of Saharan dusts in these soils (Dia et al., 2006). We have therefore analyzed 238U-234U-230Th nuclides in the same samples. Comparison of U-Th isotopic data with Sr-Nd-Pb isotopic data indicates a significant impact of the dust input on the U and Th budget of the soils, around 10% for both U and Th. Using Sr-Nd-Pb isotopic data of Saharan dusts given by Dia et al. (2006) we estimate U-Th concentrations and U-Th isotope ratios of dusts compatible with U-Th data obtained on Saharan dusts collected in Barbados (Rydell H.S. and Prospero J.M., 1972). However, the variations of U/Th ratios along the weathering profiles cannot be explained by a simple mixing scenario between material from basalt and from the defined atmospheric dust pool. A secondary uranium migration associated with chemical weathering has affected the weathering profiles. Mass balance calculation suggests that U in soils from Mount Cameroon is affected at the same order of magnitude by both chemical migration and dust accretion. Nevertheless, the Mount Cameroon is a limit case were large dust inputs from continental crust of Sahara contaminate basaltic terrain from Mount Cameroon volcano. Therefore, this study suggests that in other contexts were dust inputs are lower, or the bedrocks more concentrated in U and Th

Multi-scale simulation of quantum dot formation in Al/Al (110) homoepitaxy

NASA Astrophysics Data System (ADS)

Tiwary, Yogesh; Fichthorn, Kristen

2007-03-01

In experimental studies of Al(110) homoepitaxy, it is observed that over a certain temperature window (330-500K), 3D huts, up to 50 nm high with well defined and smooth (111) and (100) facets, form and self-organize over the micron scale [1]. The factors leading to this kinetic self-organization are currently unclear. To understand how these structures form and evolve, we simulated multi-layer, homoepitaxial growth on Al(110) using ab initio kinetic Monte Carlo (KMC). At the high temperatures, where nano-huts form, the KMC simulations are slow. To tackle this problem, we use a technique developed by Devita & Sander [2], in which isolated adatoms make multiple moves in one step. We achieve high efficiency with this algorithm and we explore very high temperatures on large simulation lattices. We uncover a variety of interesting morphologies (Ripples, mounds, smooth surface, huts) that depend on the growth temperature. By varying the barriers for various rate processes, we discern the factors that determine hut sizes, aspect ratios, and self-organization. [1] F. Buatier de Mongeot, W. Zhu, A. Molle, R. Buzio, C. Boragno, U. Valbusa, E. Wang, and Z. Zhang, Phys. Rev. Lett. 91, 016102 (2003). [2] J.P. Devita & L.M. Sander, Phys. Rev. B 72, 205421 (2005).

In-situ measurements of U-series nuclides by electron microprobe on zircons and monazites from Gandak river sediments

NASA Astrophysics Data System (ADS)

Bosia, C.; Deloule, E.; France-Lanord, C.; Chabaux, F.

2015-12-01

Determination of sediment transfer time during transport in the alluvial plains is a critical issue to correctly understand the relationship between climate, tectonics and Earth surface evolution. The residence time of river sediments may be constrained by analyzing the U series nuclides fractionations (e.g. [1] and [2]), which are created during water rock interactions by the ejection of the daughter nuclides of the grain (α-recoil) and the preferential mobilization of nuclides in decay damaged crystal structure. However, recent studies on sediments from the Gandak river, one of the main Ganga tributary, highlighted the difficulties to obtain reproducible data on bulk sediments, due to the nuggets distribution of U-Th enriched minor minerals in the samples (Bosia et al., unpublished data). We therefore decided to analyze the U and Th isotopic systematic at a grain-scale for Himalayan sediments from the Gandak river. This has been tested by performing in situ depth profiles of 238U-234U-230Th and 232Th on zircons and monazites (50-250 μm) by Secondary Ion Mass Spectrometry (SIMS) at the CRPG, Nancy, France. The first results point the occurrence of 238U-234U-230Th disequilibria in the outermost parts of both monazite and zircon minerals with a return to the equilibrium state in the core of the grains. The relative U and Th enrichment is however slightly different depending on considered minerals, suggesting possible adsorption processes of 230-Th. Coupled to a simple model of U and Th mobility during water-mineral interactions, these data should help to constrain the origin of 238U-234U-230Th disequilibria in these minerals. Moreover, the results of the study should be relevant to discuss the potential of this approach to constrain the residence time of zircons and monazites in the Gandak alluvial plain. [1] Chabaux et al., 2012, C. R. Geoscience, 344 (11-12): 688-703; [2] Granet et al., 2007, Earth and Planet. Sci. Lett., 261 (3-4): 389-406.

LA-ICP-MS and SIMS U-Pb and U-Th zircon geochronological data of Late Pleistocene lava domes of the Ciomadul Volcanic Dome Complex (Eastern Carpathians).

PubMed

Lukács, Réka; Guillong, Marcel; Schmitt, Axel K; Molnár, Kata; Bachmann, Olivier; Harangi, Szabolcs

2018-06-01

This article provides laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and secondary ionization mass spectrometry (SIMS) U-Pb and U-Th zircon dates for crystals separated from Late Pleistocene dacitic lava dome rocks of the Ciomadul Volcanic Dome Complex (Eastern Carpathians, Romania). The analyses were performed on unpolished zircon prism faces (termed rim analyses) and on crystal interiors exposed through mechanical grinding an polishing (interior analyses). 206 Pb/ 238 U ages are corrected for Th-disequilibrium based on published and calculated distribution coefficients for U and Th using average whole-rock and individually analyzed zircon compositions. The data presented in this article were used for the Th-disequilibrium correction of (U-Th)/He zircon geochronology data in the research article entitled "The onset of the volcanism in the Ciomadul Volcanic Dome Complex (Eastern Carpathians): eruption chronology and magma type variation" (Molnár et al., 2018) [1].

Neodymium Isotopic Compositions of the Titanite Reference Materials Used in U-Pb Geochronology

NASA Astrophysics Data System (ADS)

Ma, Q.; Yang, Y.; Zhao, Z.

2017-12-01

Titanite (CaTiSiO5) is a widespread mineral and preferentially incorporates considerable uranium and significant light rare earth elements (LREEs) in its structure. Geochronology based upon U-Pb and Pb-Pb analyses of titanite has proven to be useful for understanding the P-T-t evolution of many igneous, metamorphic and hydrothermally altered rock samples (Scott and St-Onge, 1995). In the meantime, Sm-Nd isotopic composition in single titanite can be used to obtain initial Nd isotope composition at the time of titanite crystallization when combined with its U-Pb age, making titanite the most versatile mineral for dating metamorphism and tracing hydrothermal source (Amelin et al., 2009). The widely utilized in situ analyses by SIMS and LA-(MC)-ICP-MS have emphasized the significance for uniform and homogeneous reference materials for external correction (Liu et al., 2012, Sun et al., 2012, Yang et al., 2014). Here, we present U-Pb ages and Sm-Nd isotope analyses of twelve natural titanite crystals (12YQ82, T004, Ontario, BLR-1, OLT1, Khan, Qinghu, TLS-36, NW-IOA, C253, Pakistan and MKED1) acquired by Agilent 7500a Q-ICP-MS and Neptune MC-ICP-MS, respectively, combined a 193 nm ArF excimer laser ablation system. For U-Pb dating, elemental fractionation and instrumental drift were externally corrected using MKED1 titanite standard, showing results of U-Pb analyses all within error of those recommended values. With respect to Sm-Nd isotopes, we employed the interference-free 147Sm/149Sm to deduct 144Sm isobaric interference on 144Nd, and the fractionation between 147Sm and 144Nd was calibrated using BLR-1 titanite, which is proved homogenous in Sm-Nd isotopic system. The obtained Sm-Nd isotopic compositions for natural titanite samples are all consistent with those values determined by isotope dilution (ID) MC-ICP-MS, demonstrating the precision and accuracy currently available for in situ Sm-Nd analyses. Our results demonstrate that BLR-1, OLT1 and Ontario titanites

48. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING N.E. AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

48. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING N.E. AT THE AMMONIUM NITRATE BUILDING UNDER CONSTRUCTION, AUGUST 24, 1918. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

El aprendizaje significativo en las ciencias al participar en proyectos de investigacion cientifica

NASA Astrophysics Data System (ADS)

Mora Polanco, Miguelena

La ciencia es el eje fundamental a traves del cual se desarrollan las habilidades necesarias para el pensar cientifico que va a la busqueda del conocimiento cientifico. La intencion de este estudio fue indagar en el tema de investigacion cientifica desde el punto de vista de los participantes en los siguientes aspectos relacionados con la experiencia de investigacion cientifica: a) conceptos, b) proceso, c) destrezas y d) disposicion. Tambien se analizaron: a) las perspectivas del metodo cientifico, b) la estrategia de ensenanza, c) la cultura cientifica y d) la exposicion del proyecto investigativo en la Feria Cientifica; como parte del aprendizaje significativo de la ciencias de los participantes. Esta investigacion cualitativa propuso como diseno el estudio de caso. Los aspectos relacionados a la experiencia de participar en proyecto de investigacion cientifica son el fenomeno o caso bajo estudio. En el estudio participaron cinco (5) estudiantes egresados de escuela publica o privada que cursaban hasta el tercer ano de estudios universitarios, conducentes a un bachillerato en educacion secundaria en ciencias o en ciencias naturales. Las tecnicas utilizadas para recopilar los datos fueron: analisis de documentos del DEPR, revision de artefactos y entrevistas profundas. Para el analisis de los datos de las entrevistas se utilizo el modelo de Wolcott (1994). Del analisis de documentos del DEPR se identificaron areas a mejorar en las guias de las cartas circulares con relacion a la investigacion escolar y la feria cientifica. El analisis de los artefactos proveyo evidencia de como los internados, simposios e investigaciones fomentan el que los estudiantes se superen en el aspecto cognitivo, se conviertan en creadores del conocimiento, al hacer suyo los conceptos para poder explicarlos al publico. De las entrevistas los participantes manifestaron que la experiencia de investigacion fue una de aprendizaje significativo que los marco para toda la vida y les expandio su

46. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING N.E. AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

46. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING N.E. AT THE LIME-NITROGEN MILL ROOM UNDER CONSTRUCTION, APRIL 23, 1918. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

44. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING S.E. AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING S.E. AT THE LIME-NITROGEN OVEN ROOM UNDER CONSTRUCTION, APRIL 23, 1918. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

45. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING N.E. AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. U.S. NITRATE PLANT UNDER CONSTRUCTION, VIEW LOOKING N.E. AT THE LIME-NITROGEN OVEN ROOM UNDER CONSTRUCTION, APRIL 23, 1918. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Development of PRIME for irradiation performance analysis of U-Mo/Al dispersion fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeong, Gwan Yoon; Kim, Yeon Soo; Jeong, Yong Jin

A prediction code for the thermo-mechanical performance of research reactor fuel (PRIME) has been developed with the implementation of developed models to analyze the irradiation behavior of U-Mo dispersion fuel. The code is capable of predicting the two-dimensional thermal and mechanical performance of U-Mo dispersion fuel during irradiation. A finite element method was employed to solve the governing equations for thermal and mechanical equilibria. Temperature-and burnup-dependent material properties of the fuel meat constituents and cladding were used. The numerical solution schemes in PRIME were verified by benchmarking solutions obtained using a commercial finite element analysis program (ABAQUS).The code was validatedmore » using irradiation data from RERTR, HAMP-1, and E-FUTURE tests. The measured irradiation data used in the validation were IL thickness, volume fractions of fuel meat constituents for the thermal analysis, and profiles of the plate thickness changes and fuel meat swelling for the mechanical analysis. The prediction results were in good agreement with the measurement data for both thermal and mechanical analyses, confirming the validity of the code. (c) 2018 Elsevier B.V. All rights reserved.« less

U.S.-Mexican Security Cooperation: the Merida Initiative and Beyond

DTIC Science & Technology

2010-07-29

Department to USAID for implementation. 71 “Cárteles Perturban al Sistema Carcelario,” El Universal, June 18, 2010. 72 Silvia Otero, “No Investigan 95...a Web .” Milenio. July 28, 2010. U.S.-Mexican Security Cooperation: the Mérida Initiative and Beyond Congressional Research Service 27 Similar

U.S.- Mexican Security Cooperation: The Merida Initiative and Beyond

DTIC Science & Technology

2010-07-29

Department to USAID for implementation. 71 “Cárteles Perturban al Sistema Carcelario,” El Universal, June 18, 2010. 72 Silvia Otero, “No Investigan 95...a Web .” Milenio. July 28, 2010. U.S.-Mexican Security Cooperation: the Mérida Initiative and Beyond Congressional Research Service 27 Similar

U.S.-Mexican Security Cooperation: the Merida Initiative and Beyond

DTIC Science & Technology

2010-08-16

2010, those funds had yet to be transferred from the State Department to USAID for implementation. 71 “Cárteles Perturban al Sistema Carcelario,” El...Quejas a Web .” Milenio. July 28, 2010. U.S.-Mexican Security Cooperation: the Mérida Initiative and Beyond Congressional Research Service 27

U-Th-Pb and Sm-Nd Isotopic Systematics of the Goalpara Ureilite

NASA Astrophysics Data System (ADS)

Torigoye, N.; Misawa, K.; Tatsumoto, M.

1993-07-01

One of the interesting features of ureilites is the light REE-enriched component that is dissolved by HNO3 leaching [1,2]. In this work, we performed acid-leaching of several mineral fractions from Goalpara ureilite for U-Th-Pb and Sm-Nd analyses. Olivine and pyroxene grains were hand-picked from 150-300- micrometer-sized fraction. Because they still contained carbon and metal sulfide they were further crushed to <63 micrometers and metal was removed with a hand magnet. These separates and whole-rock powders were washed by ethanol, and leached in 0.01N HBr, 1N HNO3, and in some cases, 7N HNO3. Concentrations of U, Th, and Pb in residues are 0.05-0.3 ppb, 0.1-0.7 ppb, and 5-100 ppb, respectively, corresponding to <=0.01X CI chondrites. Lead isotopic compositions of the residues are less radiogenic and close to Canon Diablo troilite (CDT) Pb [3] (Fig. 1). The U-Pb and Th-Pb ages of all the fractions are older than 4.5 Ga, indicating terrestrial Pb contamination (MT). Because of low concentration of U, Th, and Pb, a small amount of Pb can have a significant effect on the U-Pb and Th-Pb model ages. 238U/204Pb (mu) value of the least contaminated residue is 3, which is higher than mu (0.14-0.5) value of carbonaceous chondrites [3,4]. The higher mu value may be due to either volatile depletion by nebula fractionation or to depletion of Pb during segregation of sulfide that occurred prior to the formation of ureilite as an ultramafic cumulate. The Sm and Nd abundances in the residues are also extremely low; 0.4-2 ppb and 1-2.5 ppb, respectively, corresponding to 0.002-0.01X CI chondritic abundances. All the residues show high 147Sm/144Nd ratios (0.23 ~ 0.44), and the fraction with the highest Sm/Nd plots on the 4.55 Ga chondritic isochron (Fig. 2). The 1N HNO3 leachates do not contain light-REE-enriched components, except for the samples containing black metal-carbon phases, which also contain a large amount of terrestrial Pb in the residual fractions. Therefore

Atomistic modeling and simulation of the role of Be and Bi in Al diffusion in U-Mo fuel

NASA Astrophysics Data System (ADS)

Hofman, G. L.; Bozzolo, G.; Mosca, H. O.; Yacout, A. M.

2011-07-01

Within the RERTR program, previous experimental and modeling studies identified Si as the alloying addition to the Al cladding responsible for inhibiting Al interdiffusion in the UMo fuel. However, difficulties with reprocessing have rendered this choice inappropriate, leading to the need to study alternative elements. In this work, we discuss the results of an atomistic modeling effort which allows for the systematic study of several possible alloying additions. Based on the behavior observed in the phase diagrams, beryllium or bismuth additions suggest themselves as possible options to replace Si. The results of temperature-dependent simulations using the Bozzolo-Ferrante-Smith (BFS) method for the energetics for varying concentrations of either element are shown, indicating that Be could have a substantial effect in stopping Al interdiffusion, while Bi does not. Details of the calculations and the dependence of the role of each alloying addition as a function of temperature and concentration (of beryllium or bismuth in Al) are shown.

Synthesizing (ZrAl3 + AlN)/Mg-Al composites by a 'matrix exchange' method

NASA Astrophysics Data System (ADS)

Gao, Tong; Li, Zengqiang; Hu, Kaiqi; Han, Mengxia; Liu, Xiangfa

2018-06-01

A method named 'matrix exchange' to synthesize ZrAl3 and AlN reinforced Mg-Al composite was developed in this paper. By inserting Al-10ZrN master alloy into Mg matrix and reheating the cooled ingot to 550 °C, Al and Mg atoms diffuse to the opposite side. As a result, liquid melt occurs once the interface areas reach to proper compositions. Then dissolved Al atoms react with ZrN, leading to the in-situ formation of ZrAl3 and AlN particles, while the Al matrix is finally replaced by Mg. This study provides a new insight for preparing Mg composites.

Mechanical behaviour of AlSiC nano composites produced by ball milling and spark plasma sintering =

NASA Astrophysics Data System (ADS)

Buchheim, Claudia Sofia de Andrade Redondo Murilhas

Neste trabalho foram produzidos nanocompositos de AlSiC misturando aluminio puro com nano particulas de SiC com diâmetro de 45 - 55 nm, usando, de forma sequencial, a tecnica da metalurgia do po e a compactacao por "Spark Plasma Sintering". O composito obtido apresentava graos com 100 nm de diâmetro, encontrandose as particulas de SiC localizadas, principalmente, nas fronteiras de grao. O nanocomposito sob a forma de provetes cilindricos foi submetido a testes de compressao uniaxial e a testes de nanoindentacao para analisar a influencia das nanoparticulas de SiC, da fracao volumica de acido estearico e do tempo de moagem, nas propriedades mecânicas do material. Para efeitos de comparacao, utilizouse o comportamento mecânico do Al puro processado em condicoes similares e da liga de aluminio AA1050O. A tensao limite de elasticidade do nanocomposito com 1% Vol./Vol. de SiC e dez vezes superior a do AA1050. O refinamento de grao a escala nano constitui o principal mecanismo de aumento de resistencia mecânica. Na realidade, o Al nanocristalino sem reforco de particulas de SiC, apresenta uma tensao limite de elasticidade sete vezes superior a da liga AA1050O. A adicao de 0,5 % Vol./Vol. e de 1 % Vol./Vol. de SiC conduzem, respetivamente, ao aumento da tensao limite de elasticidade em 47 % e 50%. O aumento do tempo de moagem e a adicao de acido estearico ao po durante a moagem conduzem apenas a um pequeno aumento da tensao de escoamento. A dureza do material medida atraves de testes de nanoindentacao confirmaram os dados anteriores. A estabilidade das microestruturas do aluminio puro e do nanocomposito AlSiC, foi testada atraves de recozimento de restauracao realizado as temperaturas de 150 °C e 250 °C durante 2 horas. Aparentemente, o tratamento termico nao influenciou as propriedades mecânicas dos materiais, excepto do nanocomposito com 1 % Vol./Vol. de SiC restaurado a temperatura de 250 °C, para o qual se observou uma reducao da tensao limite de elasticidade

AlGaInN laser diode technology for systems applications

NASA Astrophysics Data System (ADS)

Najda, S. P.; Perlin, P.; Suski, T.; Marona, L.; Bockowski, M.; Leszczyński, M.; Wisniewski, P.; Czernecki, R.; Kucharski, R.; Targowski, G.; Watson, S.; Kelly, A. E.

2016-02-01

Gallium Nitride (GaN) laser diodes fabricated from the AlGaInN material system is an emerging technology that allows laser diodes to be fabricated over a very wide wavelength range from u.v. to the visible, and is a key enabler for the development of new system applications such as (underwater and terrestrial) telecommunications, quantum technologies, display sources and medical instrumentation.

U.S. Security Assistance Programs in Southern Africa: Are They Supporting National Objectives?

DTIC Science & Technology

1985-04-01

YIO (Include .-iea Codi’, SACS ’-/uLLCC IaxwelI AFB Al- 36112 (205) 293-2483 UL) j7 ()phi 1473 33 AV",, EDITION OF 1 JAN 73 IS OBSOLETE, -UJLASSIF lED...34 (8: p. 6-9) Th e CPD is soml~etimes re-ferred to as the Consolidated Data Report and is I-.ral ly an u..pdate of the AISA The heart of the AIASA is

Afghanistan: Post-Taliban Governance, Security, and U.S. Policy

DTIC Science & Technology

2010-07-21

presidency, but later joined Rabbani’s 5 A pharmaceutical plant in Sudan (Al Shifa... plant was strictly civilian in nature. 6 http://www.msnbc.msn.com/id/4540958. Afghanistan: Post-Taliban Governance, Security, and U.S. Policy...commercially profitable for China Metallurgical Group, includes construction of two coal-fired electric power plant (one of which will supply more

Supreme Court of the United States Syllabus: Hortonville Joint School District No. 1 et al. v. Hortonville Education Assn. et al. Certiorari to the Supreme Court of Wisconsin. No. 74-1606. Argued February 23-24, 1976--Decided June 17, 1976.

ERIC Educational Resources Information Center

Supreme Court of the U. S., Washington, DC.

This publication presents the full text of the U.S. Supreme Court's decision in Hortonville Joint School District No. 1 et al. v. Hortonville Education Association et al., as written by Chief Justice Burger. Also included is the text of the dissenting opinion written by Justice Stewart, as well as a brief syllabus that summarizes the major issues…

Desarrollo de un receptor polarimétrico en banda S para aplicación en estudios radioastronómicos

NASA Astrophysics Data System (ADS)

Barberis, C. M.; Bava, J. A.; Sanz, A. J.

Desde el punto de vista tecnológico, el objetivo principal de este proyecto es desarrollar un cabezal de receptor en la frecuencia de 3.3 GHz, con una temperatura del sistema de 60 K y un ancho de banda de 140 MHz. El mismo será instalado en el foco primario de un reflector parabólico de 30 metros de diámetro que funcionará como radiómetro en el IAR. El receptor es del tipo polarimétrico, con lo cual permite la posibilidad de obtener las componentes de polarización lineal y circular. Para tal fin el cabezal constará de dos ramas receptoras que amplificarán la señal y la trasladarán a una frecuencia menor, (frecuencia intermedia), permitiendo de esa forma un mejor transporte de la señal a la sala de control para su posterior procesamiento. El receptor, además de tener características polarimétricas, podrá ser usado en el contínuo y en la línea, utilizando las ventajas observacionales y de procesamiento de señal que actualmente posee el IAR.

The half-metallicity of LiMgPdSn-type quaternary Heusler alloys FeMnScZ (Z=Al, Ga, In): A first-principle study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Y. C., E-mail: gaoyc1963@126.com; Gao, X.

2015-05-15

Based on the first-principles calculations, quaternary Heusler alloys FeMnScZ (Z=Al, Ga, In) including its phase stability, band gap, the electronic structures and magnetic properties has been studied systematically. We have found that, in terms of the equilibrium lattice constants, FeMnScZ (Z=Al, Ga, In) are half-metallic ferrimagnets, which can sustain the high spin polarization under a very large amount of lattice distortions. The half-metallic band gap in FeMnScZ (Z=Al, Ga, In) alloys originates from the t{sub 1u}-t{sub 2g} splitting instead of the e{sub u}-t{sub 1u} splitting. The total magnetic moments are 3μB per unit cell for FeMnScZ (Z=Al, Ga, In) alloysmore » following the Slater–Pauling rule with the total number of valence electrons minus 18 rather than 24. According to the study, the conclusion can be drawn that all of these compounds which have a negative formation energy are possible to be synthesized experimentally.« less

Disorder induced gap states as a cause of threshold voltage instabilities in Al2O3/AlGaN/GaN metal-oxide-semiconductor high-electron-mobility transistors

NASA Astrophysics Data System (ADS)

Matys, M.; Kaneki, S.; Nishiguchi, K.; Adamowicz, B.; Hashizume, T.

2017-12-01

We proposed that the disorder induced gap states (DIGS) can be responsible for the threshold voltage (Vth) instability in Al2O3/AlGaN/GaN metal-oxide-semiconductor high-electron-mobility transistors. In order to verify this hypothesis, we performed the theoretical calculations of the capacitance voltage (C-V) curves for the Al2O3/AlGaN/GaN structures using the DIGS model and compared them with measured ones. We found that the experimental C-V curves with a complex hysteresis behavior varied with the maximum forward bias and the sweeping rate can be well reproduced theoretically by assuming a particular distribution in energy and space of the DIGS continuum near the Al2O3/AlGaN interface, i.e., a U-shaped energy density distribution and exponential depth decay from the interface into Al2O3 layer (up to 4 nm), as well as suitable DIGS capture cross sections (the order of magnitude of 10-15 cm2). Finally, we showed that the DIGS model can also explain the negative bias induced threshold voltage instability. We believe that these results should be critical for the successful development of the passivation techniques, which allows to minimize the Vth instability related effects.

Accurate 238U(n , 2 n )237U reaction cross-section measurements from 6.5 to 14.8 MeV

NASA Astrophysics Data System (ADS)

Krishichayan, Bhike, M.; Tornow, W.; Tonchev, A. P.; Kawano, T.

2017-10-01

The cross section for the 238U(n ,2 n )237U reaction has been measured in the incident neutron energy range from 6.5 to 14.8 MeV in small energy steps using an activation technique. Monoenergetic neutron beams were produced via the 2H(d ,n )3He and 3H(d ,n )4He reactions. 238U targets were activated along with Au and Al monitor foils to determine the incident neutron flux. The activity of the reaction products was measured in TUNL's low-background counting facility using high-resolution γ -ray spectroscopy. The results are compared with previous measurements and latest data evaluations. Statistical-model calculations, based on the Hauser-Feshbach formalism, have been carried out using the CoH3 code and are compared with the experimental results. The present self-consistent and high-quality data are important for stockpile stewardship and nuclear forensic purposes as well as for the design and operation of fast reactors.

Organizing for Effective Joint Warfare: A Deductive Analysis of U.S. Armed Forces Joint Doctrine

DTIC Science & Technology

1993-06-18

8217, Unpublished SAMS Monogram , (U.S. Army Command and General Staff College, Fort Leavenworth, KS: i988) p. 25. 3. Frank 0. Hough, et al, History of...SAMS Monogram , (U.S. Army Command and General Staff College, Fort Leavenworth, KS: 1988) , p, 16 and p. 29; and William 0. Pierce, ’Span of Control and...The Operational Commandetr: Is it More Than Just a Nun:ber?", Unpublished SAMS Monogram , (U.S. Army Command and Ueneral Staff College, Fort Leavenworth

77 FR 54655 - Genesee & Wyoming Inc.-Control-RailAmerica, Inc., et al.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-05

... & Wyoming Inc.--Control--RailAmerica, Inc., et al. AGENCY: Surface Transportation Board. ACTION: Decision No... August 6, 2012, by Genesee and Wyoming Inc. (GWI) and RailAmerica, Inc. (RailAmerica). The application seeks Board approval under 49 U.S.C. 11323-11325 of the acquisition of control of RailAmerica, a...

Diagenesis of fossil coral skeletons: Correlation between trace elements, textures, and 234U /238U

NASA Astrophysics Data System (ADS)

Bar-Matthews, M.; Wasserburg, G. J.; Chen, J. H.

1993-01-01

A comparative study of Pleistocene fossil coral skeletons and of modern coral skeletons was carried out using petrographie and trace element analyses on a suite of Pleistocene samples that had previously been studied for 234U, 230Th, and U- 230Th ages ( CHEN et al. 1991). Evidence of a range of diagenetic changes can be recognized by optical (OM) and scanning electron microscopy (SEM). The normal texture exhibited by modern corals under OM consists of fine needles of aragonite forming a radial-fibrous pattern around a central dark line (center of calcification). This pattern can also be seen in many fossil corals. In most cases, the central dark line partially disappears during diagenesis, the radialfibrous pattern is obscured, and there is a distinct coarsening of the radial fabric of aragonite to unoriented platy or equant aragonite crystals. SEM images show diagenetic textures ranging from dense structureless images of the coralline matrix, with sharp boundaries at the septa walls, to the development of (1) a patchy distribution of dissolution micropores partially filled with aragonite fibers in the matrix, (2)aragonite needles coming from selvages in the septa walls which radiate into the septa voids. Using an electron microprobe and SEM, concentrations of Na, S, Sr, and Mg were measured. No other trace elements were detected. Na, S, and Mg contents of the matrix, the fibrous micropores, and radiating needles are highly variable and well correlated. High concentrations of Na, S, and Mg were found in modern living corals with lower concentrations in fossil corals and fibrous micropores, and the lowest value in the radiating needles. The reason for the correlations of Na, S, and Mg and crystal chemistry and the response to diagenesis of these trace elements is not understood. The average concentrations of Na, S, and Mg for each sample, when plotted against the whole coral initial δ 234U, are generally correlated ( CHEN et al., 1991). As all these diagenetic

Bin Ladin’s Killing and its Effect on Al-Qaida: What Comes Next? CTC Sentinel, Special Issue, May 2011.

DTIC Science & Technology

2011-05-01

painstakingly pieced back together an organization that had been all but destroyed by a critical drone strike and years of arrests, ultimately...Yemen after 9/11. In November 2002, a U.S. drone strike killed Abu Ali al-Harithi, the top al-Qa`ida commander in the country. Al-Harithi’s death...desire by the kidnappers, led by Abu Zeid, to curry favor with Bin Ladin himself instead of al-Zawahiri, who has been Droukdel’s 4 While it is

Al3+ ions dependent structural and magnetic properties of Co-Ni nano-alloys.

PubMed

Kadam, R H; Alone, Suresh T; Gaikwad, Anil S; Birajdar, A P; Shirsath, Sagar E

2014-06-01

Ferrite samples with a chemical formula Co0.5Ni0.5Al(x)Fe(2-x)O4 (where x = 0.0, 0.25, 0.5, 0.75 and 1.0) were synthesized by sol-gel auto-combustion method. The synthesized samples were annealed at 600 degrees C for 4 h. An analysis of X-ray diffraction (XRD) patterns reveals the formation of single phase cubic spinel structure. The lattice parameter decreased linearly with the increasing Al content x. Nano size of the powders were confirmed by the transmission electron micrographs (TEM). Particle size, bulk density decreased whereas specific surface area and porosity of the samples increased with the Al substitution. Cation distribution of constituent ions shows linear dependence of Al substitution. Based on the cation distribution obtained from XRD data, structural parameters such as lattice parameters, ionic radii of available sites and the oxygen parameter 'u' is calculated. Saturation magnetization (M(s)), magneton number (n(B)) and coercivity (H(c)) decreased with the Al substitution. Possible explanation for the observed structural and magnetic behavior with various Al content are discussed.

Ion microprobe U-Pb dating and strontium isotope analysis of biogenic apatite

NASA Astrophysics Data System (ADS)

Sano, Y.; Toyoshima, K.; Takahata, N.; Shirai, K.

2012-12-01

the combination of U-Pb dating and strontium isotope analysis of biogenic apatite. This method may be useful to extract the information of the chemistry of Past ocean in future. [1] Sweet and Donoghue (2001) J. Paleont. 75, 1174-1184. [3] Sano et al., (1999) Chem. Geol. 153, 249-258. [3] Sano and Terada (2001) Geophys. Res. Lett. 28, 831-834. [4] Sano et al. (2006) Geochem. J. 40, 597-608. [5] Takahata et al. (2008) Gondwana Res. 14, 587-596. [6] Prokoph et al. (2008) Earth Sci. Rev. 87, 113-133. [7] Karhu and Epstein (1986) Geochim. Cosmochim. Acta 50, 1745-1756. [8] Sano et al. (2008) App. Geochem. 23, 2406-2413.

U.S. Foreign Policy in Asia in the 21st Century

DTIC Science & Technology

1990-05-10

21 February 1989, p.Al. 6. Hobart Rowen, "Japan’s Growth Is Good For Us," Washington Post, 8 September 1988, p.A21. 7. Daniel Sneider, "Japan Shuns...The Pacific Is Long Overdue," publication and date unknown, p.62. 11. Daniel Sneider, "Pacific Rim Nations Strengthen Economic Ties," Christian Science...Susan Chira , "Japan Ready To Share Burden, But Also The Power, With U.S.," New York Times, 7 March 1989, p.Al. 18. Susan Chira , "Japan And The World

Activation of the Wnt/{beta}-catenin signaling pathway is associated with glial proliferation in the adult spinal cord of ALS transgenic mice

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Yanchun; Department of Histology and Embryology, Shandong University School of Medicine, Jinan, Shandong; Guan, Yingjun, E-mail: guanyj@wfmc.edu.cn

Highlights: Black-Right-Pointing-Pointer Wnt3a and Cyclin D1 were upregulated in the spinal cord of the ALS mice. Black-Right-Pointing-Pointer {beta}-catenin translocated from the cell membrane to the nucleus in the ALS mice. Black-Right-Pointing-Pointer Wnt3a, {beta}-catenin and Cyclin D1 co-localized for astrocytes were all increased. Black-Right-Pointing-Pointer BrdU/Cyclin D1 double-positive cells were increased in the spinal cord of ALS mice. Black-Right-Pointing-Pointer BrdU/Cyclin D1/GFAP triple-positive cells were detected in the ALS mice. -- Abstract: Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disease characterized by the progressive and fatal loss of motor neurons. In ALS, there is a significant cell proliferation in response to neurodegeneration; however,more » the exact molecular mechanisms of cell proliferation and differentiation are unclear. The Wnt signaling pathway has been shown to be involved in neurodegenerative processes. Wnt3a, {beta}-catenin, and Cyclin D1 are three key signaling molecules of the Wnt/{beta}-catenin signaling pathway. We determined the expression of Wnt3a, {beta}-catenin, and Cyclin D1 in the adult spinal cord of SOD1{sup G93A} ALS transgenic mice at different stages by RT-PCR, Western blot, and immunofluorescence labeling techniques. We found that the mRNA and protein of Wnt3a and Cyclin D1 in the spinal cord of the ALS mice were upregulated compared to those in wild-type mice. In addition, {beta}-catenin translocated from the cell membrane to the nucleus and subsequently activated transcription of the target gene, Cyclin D1. BrdU and Cyclin D1 double-positive cells were increased in the spinal cord of these mice. Moreover, Wnt3a, {beta}-catenin, and Cyclin D1 were also expressed in both neurons and astrocytes. The expression of Wnt3a, {beta}-catenin or Cyclin D1 in mature GFAP{sup +} astrocytes increased. Moreover, BrdU/Cyclin D1/GFAP triple-positive cells were detected in the ALS mice. Our findings suggest

76 FR 37857 - Russell Exchange Traded Funds Trust, et al.; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-28

... Exchange Traded Funds Trust, et al.; Notice of Application June 22, 2011. AGENCY: Securities and Exchange... sections 12(d)(1)(A) and (B) of the Act. APPLICANTS: Russell Exchange Traded Funds Trust (formerly, U.S. One Trust, the ``Trust''), Russell Investment Management Company (``Advisor''), and ALPS Distributors...

Comparison of thermal compatibility between atomized and comminuted U{sub 3}Si dispersion fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryu, Woo-Seog; Park, Jong-Man; Kim, Chang-Kyu

1997-08-01

Thermal compatibility of atomized U{sub 3}Si dispersion fuels were evaluated up to 2600 hours in the temperature range from 250 to 500{degrees}C, and compared with that of comminuted U{sub 3}Si. Atomized U{sub 3}Si showed better performance in terms of volume expansion of fuel meats. The reaction zone of U{sub 3}Si and Al occurred along the grain boundaries and deformation bands in U{sub 3}Si particles. Pores around fuel particles appeared at high temperature or after long-term annealing tests to remain diffusion paths over the trench of the pores. The constraint effects of cladding on fuel rod suppressed the fuel meat, andmore » reduced the volume expansion.« less

Interfacial Chemical Interactions in the (Alumina/Graphite/Al Alloys) System: Thermodynamic Modeling and Experimental Results

NASA Astrophysics Data System (ADS)

Gelbstein, M.; Edry, I.; Froumin, N.; Frage, N.

2009-04-01

The stability of alumina-coated graphite couples in liquid Al is investigated in the 1373 to 1573 K temperature range. A thermodynamic model was carried out to determine the mechanisms controlling the couple stability and the effect of alloying Al with high melting point element for instance U (up to 3 at. pct). It was established that the dissolved uranium dose not play any role in the interfacial interactions and that the couple stability is governed by the interactions with Al resulting in the release of gaseous products. The experiments focused on wetting kinetics under conditions allowing for an in-situ reduction of the alumina coating by the liquid Al. The experimental results confirm the predictions of the thermodynamic analysis.

Tri-Lateral Noor al Salaam High Concentration Solar Central Receiver Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blackmon, James B

2008-03-31

This report documents the efforts conducted primarily under the Noor al Salaam (“Light of Peace”) program under DOE GRANT NUMBER DE-FC36-02GO12030, together with relevant technical results from a closely related technology development effort, the U.S./Israel Science and Technology Foundation (USISTF) High Concentration Solar Central Receiver program. These efforts involved preliminary design, development, and test of selected prototype power production subsystems and documentation of an initial version of the system definition for a high concentration solar hybrid/gas electrical power plant to be built in Zaafarana, Egypt as a first step in planned commercialization. A major part of the planned work wasmore » halted in 2007 with an amendment in October 2007 requiring that we complete the technical effort by December 31, 2007 and provide a final report to DOE within the following 90 days. This document summarizes the work conducted. The USISTF program was a 50/50 cost-shared program supported by the Department of Commerce through the U.S./Israel Science and Technology Commission (USISTC). The USISTC was cooperatively developed by President Clinton and the late Prime Minister Rabin of Israel "to encourage technological collaboration" and "support peace in the Middle East through economic development". The program was conducted as a follow-on effort to Israel's Magnet/CONSOLAR Program, which was an advanced development effort to design, fabricate, and test a solar central receiver and secondary optics for a "beam down" central receiver concept. The status of these hardware development programs is reviewed, since they form the basis for the Noor al Salaam program. Descriptions are provided of the integrated system and the major subsystems, including the heliostat, the high temperature air receiver, the power conversion unit, tower and tower reflector, compound parabolic concentrator, and the master control system. One objective of the USISTF program was to

Thermal Stability of Pseudomorphic In(x)Ga(1-x)As/In(y)Al(1-y)As/InP heterostructures

DTIC Science & Technology

1993-04-22

structure. Pseudomorphic layers of nAlAs with co= n - After the first anneal, R = 67%. We performed additional parable mismatch were also characterized by...MiAbi,,%,b, w*am.¶0’ (004) 00Afl’%,A 0 .A. dwd,u,(004) 500 A in, oAl. ,oAs -: .2w %r,•.& s *ae It GW 0 50 105s,1 n (e u~f ’• T ’ o"....... . .. I5 o...1989). S10 0 •---1 [21 J. W. Matthews and A. E. Blakeslee, "Defects in epitaxial multilayers," J. CrPt. Growth 27, 118 (1974). (80003 M. Tacano, Y

A study of the semiconductor compound СuAlO2 by the method of nuclear quadrupole resonance of Cu

NASA Astrophysics Data System (ADS)

Matukhin, V. L.; Khabibulin, I. Kh.; Shul'gin, D. A.; Smidt, S. V.

2012-07-01

The method of nuclear quadrupole resonance of Cu (NQR Cu) is used to study the samples of a semiconductor compound CuAlO2. The crystal structure of CuAlO2 belongs to the family of delafossite - the mineral of a basic CuFeO2 structure. Transparent semiconductor oxides, such as CuAlO2, have attracted recent attention as promising thermoelectric materials.

Thermodynamic and structural properties of hcp bulk and nano-precipitated Ag-Al.

NASA Astrophysics Data System (ADS)

Zarkevich, Nikolai; Johnson, Duane; Smirnov, Andrei

2002-03-01

We study the short- and long- range chemical ordering in hcp bulk Ag_2Al using the Monte Carlo method based on a Hamiltonian constructed via structural formation energies from ab initio electronic-structure calculations. We find that the ground-state structure and thermodynamic properties of bulk Ag_2Al is that determined from the X-ray experimental data. We also address the influence of the interface, coherency strain, and off-stoichiometric disorder on the structure of metastable γ' nano-precipitates in fcc Al matrix. We show that γ' precipitates are off-stoichiometric and provide a new Al-rich structure that reproduces the observed TEM image. We acknowledge our support in part by an ALCOA Foundation Grant, the U.S. Department of Energy through the Frederick Seitz Materials Research Laboratory at UIUC under grant DEFG02-91ER45439, and the UIUC Materials Computation Center under National Science Foundation grant DMR-9976550.

Are U-Series Disequilibria Transparent to Crustal Processing of Magma? A Case Study at Bezymianny and Klyuchevskoy Volcanoes, Kamchatka, Russia

NASA Astrophysics Data System (ADS)

Kayzar, T. M.; Nelson, B. K.; Bachmann, O.; Portnyagin, M.; Ponomareva, V.

2010-12-01

Disequilibria in the short-lived uranium-series isotopic system can provide timescales of magma production, modification and transport in all tectonic settings. In volcanic arcs, the field has converged on the concept that (238U/230Th) and (226Ra/230Th) activities greater than one are a result of fluid fluxing from the slab to mantle wedge, and that the preservation of (226Ra/230Th) disequilibria requires rapid transport of melts from the mantle wedge to the surface (226Ra returns to equilibrium with 230Th in ~8000 years). The need for rapid transport coupled with the incompatibility of U-series elements suggest that U-series fractionation is not measurably affected by crustal processes. However, some well-studied arc systems, including the very productive Central Kamchatka Depression (CKD) of the Kamchatkan volcanic arc, show U-series data that are in conflict with this commonly accepted model. Our study focuses on two neighboring volcanic systems, Bezymianny and Klyuchevskoy volcanoes in the CKD. Separated by ~10km, these two systems are thought to share the same mantle source. Klyuchevskoy has primitive compositions (51-56 wt%) while Bezymianny erupts more differentiated andesites (57-63 wt% SiO2); therefore, by examining the U-series signals in these two systems it is possible to decouple a primary signal from one having undergone crustal processing. We record whole rock (238U/230Th) values for Bezymianny ranging from 0.94 to 0.96 in modern eruptive products, while (226Ra/230Th) are >1. We also observe a similar signal in older (212-6791BP) tephra deposits from Klyuchevskoy, measuring (238U/230Th) of 0.92-0.99 (unpublished data, collaborative research with the KALMAR project). (238U/230Th) <1 in arcs have mostly been reported from areas of thick continental crust (Andes; Sigmarsson et al. 1998, Garrison et al. 2006, Jicha et al. 2007) or from an arc where phases such as garnet and/or Al-rich clinopyroxene can retain a high U/Th in the crystalline residue (Jicha

Computational materials design of attractive Fermion system with large negative effective Ueff in the hole-doped Delafossite of CuAlO2, AgAlO2 and AuAlO2: Charge-excitation induced Ueff < 0

NASA Astrophysics Data System (ADS)

Nakanishi, A.; Fukushima, T.; Uede, H.; Katayama-Yoshida, H.

2015-12-01

On the basis of general design rules for negative effective U(Ueff) systems by controlling purely-electronic and attractive Fermion mechanisms, we perform computational materials design (CMD®) for the negative Ueff system in hole-doped two-dimensional (2D) Delafossite CuAlO2, AgAlO2 and AuAlO2 by ab initio calculations with local density approximation (LDA) and self-interaction corrected-LDA (SIC-LDA). It is found that the large negative Ueff in the hole-doped attractive Fermion systems for CuAlO2 (UeffLDA = - 4.53 eV and UeffSIC-LDA = - 4.20 eV), AgAlO2 (UeffLDA = - 4.88 eV and UeffSIC-LDA = - 4.55 eV) and AuAlO2 (UeffLDA = - 4.14 eV and UeffSIC-LDA = - 3.55 eV). These values are 10 times larger than that in hole-doped three-dimensional (3D) CuFeS2 (Ueff = - 0.44 eV). For future calculations of Tc and phase diagram by quantum Monte Carlo simulations, we propose the negative Ueff Hubbard model with the anti-bonding single π-band model for CuAlO2, AgAlO2 and AuAlO2 using the mapped parameters obtained from ab initio electronic structure calculations. Based on the theory of negative Ueff Hubbard model (Noziéres and Schmitt-Rink, 1985), we discuss |Ueff| dependence of superconducting critical temperature (Tc) in the 2D Delafossite of CuAlO2, AgAlO2 and AuAlO2 and 3D Chalcopyrite of CuFeS2, which shows the interesting chemical trend, i.e., Tc increases exponentially (Tc ∝ exp [ - 1 / | Ueff | ]) in the weak coupling regime | Ueff(- 0.44 eV) | < W(∼ 2 eV) (where W is the band width of the negative Ueff Hubbard model) for the hole-doped CuFeS2, and then Tc goes through a maximum when | Ueff(- 4.88 eV , - 4.14 eV) | ∼ W(2.8 eV , 3.5 eV) for the hole-doped AgAlO2 and AuAlO2, and finally Tc decreases with increasing |Ueff| in the strong coupling regime, where | Ueff(- 4.53 eV) | > W(1.7 eV) , for the hole-doped CuAlO2.

PROGRAMA PARA LA VERIFICACIN DE LA TECNOLOGIA AMBIENTAL/ENVIRONMENTAL TECHNOLOGY VERIFICATION PROGRAM (ETV) (EPA/600/F-98/015A)

EPA Science Inventory

A travs de su historia, la Agencia de Proteccin del Medio Ambiente estadounidense (U.S. Environmental Protection Agency, EPA) ha evaluado distintas tecnologas para determinar su efectividad en el monitoreo, la prevencin, el control, y la limpieza de la contaminacin ambiental. Sin...

Al Umchaimin depression, Western Iraq: An impact structure?

NASA Astrophysics Data System (ADS)

Underwood, James R., Jr.

Al Umchaimin, in Arabic 'hiding place' or 'place of ambush', is located at latitude 32 degrees 35.5 N and longitude 39 degrees 25 E. The nearly circular depression averages 2.75 km in diameter and is 33-42 m deep. It is floored with fine-grained, clay-rich deposits, estimated to be 36 m thick, the surface of which shows well-developed desiccation fissures or mudcracks when dry. Because of its nearly circular planimetric shape and its apparent isolation from other surface and subsurface features, it has been considered by some to be a possible meteorite impact structure and by others to be a surface collapse feature that originated following removal of magma from the subsurface as the magma extruded elsewhere. Al Umchaimin was listed in the U.S. Geological Survey tabulation of 110 structures worldwide for which a meteorite impact origin had been suggested. It was placed in Category 6 Structures for which more data are required for classification. It is concluded that, on the basis of the studies that have been made of Al Umchaimin and on the basis of the brief site visit made, Al Umchaimin probably is not an impact structure but most likely resulted from the enlargement and coalescence of sink holes and eventual collapse of the roof material into the resulting cavity.

Al Umchaimin depression, Western Iraq: An impact structure?

NASA Technical Reports Server (NTRS)

Underwood, James R., Jr.

1992-01-01

Al Umchaimin, in Arabic 'hiding place' or 'place of ambush', is located at latitude 32 degrees 35.5 N and longitude 39 degrees 25 E. The nearly circular depression averages 2.75 km in diameter and is 33-42 m deep. It is floored with fine-grained, clay-rich deposits, estimated to be 36 m thick, the surface of which shows well-developed desiccation fissures or mudcracks when dry. Because of its nearly circular planimetric shape and its apparent isolation from other surface and subsurface features, it has been considered by some to be a possible meteorite impact structure and by others to be a surface collapse feature that originated following removal of magma from the subsurface as the magma extruded elsewhere. Al Umchaimin was listed in the U.S. Geological Survey tabulation of 110 structures worldwide for which a meteorite impact origin had been suggested. It was placed in Category 6 Structures for which more data are required for classification. It is concluded that, on the basis of the studies that have been made of Al Umchaimin and on the basis of the brief site visit made, Al Umchaimin probably is not an impact structure but most likely resulted from the enlargement and coalescence of sink holes and eventual collapse of the roof material into the resulting cavity.

Generating para-water from para-hydrogen: A Gedankenexperiment.

PubMed

Ivanov, Konstantin L; Bodenhausen, Geoffrey

2018-07-01

A novel conceptual approach is described that is based on the transfer of hyperpolarization from para-hydrogen in view of generating a population imbalance between the two spin isomers of H 2 O. The approach is analogous to SABRE (Signal Amplification By Reversible Exchange) and makes use of the transfer of spin order from para-hydrogen to H 2 O in a hypothetical organometallic complex. The spin order transfer is expected to be most efficient at avoided level crossings. The highest achievable enrichment levels of para- and ortho-water are discussed. Copyright © 2018 Elsevier Inc. All rights reserved.

Commercial Eyes in Space: Implications for U.S. Military Operations in 2030

DTIC Science & Technology

2008-03-01

r C om m er ci al Im ag er y C om pa ny Su bj ec t Figure 2: Notional Satellite Remote Sensing Flow and...Government will most likely continue to rely on commercial sensors to supplement national intelligence 14 A dv er sa ry U se r C om m er ci al Im ag er y...C om pa ny Su bj ec t Potential Counter ISR Strategies for 2030 Image Request Tasking Recv’d Satellite Tasked Image Processed & Stored

Magnetism of Al-substituted magnetite reduced from Al-hematite

NASA Astrophysics Data System (ADS)

Jiang, Zhaoxia; Liu, Qingsong; Zhao, Xiang; Roberts, Andrew P.; Heslop, David; Barrón, Vidal; Torrent, José

2016-06-01

Aluminum-substituted magnetite (Al-magnetite) reduced from Al-substituted hematite or goethite (Al-hematite or Al-goethite) is an environmentally important constituent of magnetically enhanced soils. In order to characterize the magnetic properties of Al-magnetite, two series of Al-magnetite samples were synthesized through reduction of Al-hematite by a mixed gas (80% CO2 and 20% CO) at 395°C for 72 h in a quartz tube furnace. Al-magnetite samples inherited the morphology of their parent Al-hematite samples, but only those transformed from Al-hematite synthesized at low temperature possessed surficial micropores, which originated from the release of structural water during heating. Surface micropores could thus serve as a practical fingerprint of fire or other high-temperature mineralogical alteration processes in natural environments, e.g., shear friction in seismic zones. In addition, Al substitution greatly affects the magnetic properties of Al-magnetite. For example, coercivity (Bc) increases with increasing Al content and then decreases slightly, while the saturation magnetization (Ms), Curie temperature (Tc), and Verwey transition temperature (Tv) all decrease with increasing Al content due to crystal defect formation and dilution of magnetic ions caused by Al incorporation. Moreover, different trends in the correlation between Tc and Bc can be used to discriminate titanomagnetite from Al-magnetite, which is likely to be important in environmental and paleomagnetic studies, particularly in soil.

Forest Bird Distribution, Density and Trends in the Ka'u Region of Hawai'i Island

USGS Publications Warehouse

Gorresen, P. Marcos; Camp, Richard J.; Pratt, Thane K.

2007-01-01

An accurate and current measure of population status and trend is necessary for conservation and management efforts. Scott and Kepler (1985) provided a comprehensive review of the status of native Hawaiian birds based on the extensive Hawaii Forest Bird Survey (HFBS) of the main islands (Scott et al. 1986). At that time, they documented declining populations and decreasing ranges for most species, and the extinction of several species over the previous 50 years. Many native bird species continue to decline throughout Hawai`i (Camp et al. In review, Gorresen et al. In prep.). The focus of this study is the mid-to-high elevation rainforest on the southeast windward slopes of Mauna Loa Volcano (Figure 1). Known as Ka`u, the region encompasses forest lands protected by Kamehameha Schools, The Nature Conservancy, Hawai`i Volcanoes National Park (HVNP), and the State of Hawai'i's Ka`u Forest Reserve, Kapapala Forest Reserve and Kapapala Cooperative Game Management Area,. Together these lands support one of three main concentrations of native forest birds on the Hawai`i Island (the other two being centered on the Hakalau Forest National Wildlife Refuge and Kulani-Keauhou area in the north and central windward part of the island, respectively.) Because this region harbors important populations of native and endangered forest birds in some of the best remaining forest habitat on the island, it has been a focus of forest bird surveys since the 1970s. The Ka`u region was first quantitatively surveyed in 1976 by the Hawaii Forest Bird Survey (Scott et al. 1986). Surveys were conducted by State of Hawai`i Division of Forestry and Wildlife in 1993 and 2002 and by the U.S. National Park Service and the U.S. Geological Survey in 2004 and 2005. In this report, we present analyses of the density, distribution and trends of native and introduced forest bird within the Ka`u region of Hawai`i Island. The analyses cover only those species with sufficient detections to model detection

First-Principles Thermodynamics Study of Spinel MgAl 2 O 4 Surface Stability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Qiuxia; Wang, Jian-guo; Wang, Yong

The surface stability of all possible terminations for three low-index (111, 110, 100) structures of the spinel MgAl2O4 has been studied using first-principles based thermodynamic approach. The surface Gibbs free energy results indicate that the 100_AlO2 termination is the most stable surface structure under ultra-high vacuum at T=1100 K regardless of Al-poor or Al-rich environment. With increasing oxygen pressure, the 111_O2(Al) termination becomes the most stable surface in the Al-rich environment. The oxygen vacancy formation is thermodynamically favorable over the 100_AlO2, 111_O2(Al) and the (111) structure with Mg/O connected terminations. On the basis of surface Gibbs free energies for bothmore » perfect and defective surface terminations, the 100_AlO2 and 111_O2(Al) are the most dominant surfaces in Al-rich environment under atmospheric condition. This is also consistent with our previously reported experimental observation. This work was supported by a Laboratory Directed Research and Development (LDRD) project of the Pacific Northwest National Laboratory (PNNL). The computing time was granted by the National Energy Research Scientific Computing Center (NERSC). Part of computing time was also granted by a scientific theme user proposal in the William R. Wiley Environmental Molecular Sciences Laboratory (EMSL), which is a U.S. Department of Energy national scientific user facility located at PNNL in Richland, Washington.« less

Familial ALS

PubMed Central

Boylan, Kevin

2015-01-01

Synopsis Genes linked to ALS susceptibility are being identified at an increasing rate owing to advances in molecular genetic technology. Genetic mechanisms in ALS pathogenesis appear to exert major effects in ~10% of patients, but genetic factors at some level may be important components of disease risk in most ALS patients. Identification of gene variants associated with ALS has informed concepts of the pathogenesis of ALS, aided the identification of therapeutic targets, facilitated research to develop new ALS biomarkers, and supported the establishment of clinical diagnostic tests for ALS-linked genes. Translation of this knowledge to ALS therapy development is ongoing. PMID:26515623

Ab initio modeling of zincblende AlN layer in Al-AlN-TiN multilayers

DOE PAGES

Yadav, S. K.; Wang, J.; Liu, X. -Y.

2016-06-13

An unusual growth mechanism of metastable zincblende AlN thin film by diffusion of nitrogen atoms into Al lattice is established. Using first-principles density functional theory, we studied the possibility of thermodynamic stability of AlN as a zincblende phase due to epitaxial strains and interface effect, which fails to explain the formation of zincblende AlN. We then compared the formation energetics of rocksalt and zincblende AlN in fcc Al through direct diffusion of nitrogen atoms to Al octahedral and tetrahedral interstitials. Furthermore, the formation of a zincblende AlN thin film is determined to be a kinetically driven process, not a thermodynamicallymore » driven process.« less

Interfacial characterization of Al-Al thermocompression bonds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malik, N., E-mail: nishantmalik1987@gmail.com; SINTEF ICT, Department of Microsystems and Nanotechnology, P.O. Box 124 Blindern, N-0314 Oslo; Carvalho, P. A.

2016-05-28

Interfaces formed by Al-Al thermocompression bonding were studied by the transmission electron microscopy. Si wafer pairs having patterned bonding frames were bonded using Al films deposited on Si or SiO{sub 2} as intermediate bonding media. A bond force of 36 or 60 kN at bonding temperatures ranging from 400–550 °C was applied for a duration of 60 min. Differences in the bonded interfaces of 200 μm wide sealing frames were investigated. It was observed that the interface had voids for bonding with 36 kN at 400 °C for Al deposited both on Si and on SiO{sub 2}. However, the dicing yield was 33% for Al onmore » Si and 98% for Al on SiO{sub 2}, attesting for the higher quality of the latter bonds. Both a bond force of 60 kN applied at 400 °C and a bond force of 36 kN applied at 550 °C resulted in completely bonded frames with dicing yields of, respectively, 100% and 96%. A high density of long dislocations in the Al grains was observed for the 60 kN case, while the higher temperature resulted in grain boundary rotation away from the original Al-Al interface towards more stable configurations. Possible bonding mechanisms and reasons for the large difference in bonding quality of the Al films deposited on Si or SiO{sub 2} are discussed.« less

U.S. Naval Strategy in the 1990s: Selected Documents

DTIC Science & Technology

2006-09-01

Crawshaw , USN; Capt. Eric Briggs, USN; Capt. Charles Schaefer, USN; Cdr. Joseph Connelly, USN; Cdr. Al Seifert, USN; Capt. Frank Dobrydney, USN. † Vice...countermeasures 33 counter-terrorism 206, 208 courage 107 CPAM See CNO Program Analysis Memorandum Crawshaw , Robert 88 U . S . N A V A L S T R A T E G Y I N T

Thermal Modeling of Al-Al and Al-Steel Friction Stir Spot Welding

NASA Astrophysics Data System (ADS)

Jedrasiak, P.; Shercliff, H. R.; Reilly, A.; McShane, G. J.; Chen, Y. C.; Wang, L.; Robson, J.; Prangnell, P.

2016-09-01

This paper presents a finite element thermal model for similar and dissimilar alloy friction stir spot welding (FSSW). The model is calibrated and validated using instrumented lap joints in Al-Al and Al-Fe automotive sheet alloys. The model successfully predicts the thermal histories for a range of process conditions. The resulting temperature histories are used to predict the growth of intermetallic phases at the interface in Al-Fe welds. Temperature predictions were used to study the evolution of hardness of a precipitation-hardened aluminum alloy during post-weld aging after FSSW.

Fractionation in the solar nebula. II - Condensation of Th, U, Pu and Cm

NASA Technical Reports Server (NTRS)

Boynton, W. V.

1978-01-01

Reasonable assumptions concerning activity coefficients allow the calculation of the relative volatility of the actinide elements under conditions expected during the early history of the solar system. Several of the light rare earths have volatilities similar to Pu and Cm and can be used as indicators of the degree of fractionation of these extinct elements. Uranium is considerably more volatile than either Pu or Cm, leading to fractionations of about a factor of 50 and 90 in the Pu/U and Cm/U ratio in the earliest condensates from the solar nebula. Ca,Al-rich inclusions from the Allende meteorite, including the coarse-grained inclusions, have a depletion of U relative to La of about a factor of three, suggesting that these inclusions may have been isolated from the nebular gas before condensation of U was complete. The inclusions, however, can be used to determine solar Pu/U and Cm/U ratios if the rare earth patterns are determined in addition to the other normal measurements.

Implementação de um algoritmo para a limpeza de mapas da RCFM

NASA Astrophysics Data System (ADS)

Souza, C. L.; Wuensche, C. A.

2003-08-01

A Radiação Cósmica de Fundo em Microondas (RCFM), descoberta por Penzias e Wilson em 1965, é uma das ferramentas mais poderosas para o estudo da cosmologia. Com a descoberta de flutuações de temperatura na RCFM, da ordem de uma parte em 105, pelo COBE (1992), uma nova era teve início. Nos últimos onze anos, diversos instrumentos fizeram novas medidas de alta precisão, refinando os resultados apresentados pelo COBE, culminando com os resultados recentes do satélite WMAP. A análise de dados da RCFM, especialmente no caso de experimentos com pequena cobertura do céu, apresenta uma série de dificuldades devido a emissões de contaminantes externos, tais como a emissão da Galáxia e de fontes pontuais, e de ruídos intrínsecos tanto ao sistema de detecção quanto à estratégia de observação do céu. Uma das soluções típicas para a filtragem de dados brutos de um experimento para medir flutuações de temperatura é aplicar um gabarito (template) e um filtro passa alta ao produzir mapas simplificados (sem considerar matrizes de correlação ou covariância). No caso de experimentos que utilizam detectores HEMT, essa combinação de filtros remove, satisfatoriamente, ruídos do tipo 1/f gerados pela instabilidade no ganho do detector acoplado ao movimento do instrumento, definido pela estratégia de observação. Entretanto, o sinal resultante medido, tanto em simulações quanto em séries temporais reais, sugere que parte do sinal cosmológico pode estar sendo removido junto com o ruído dos detectores. Este trabalho descreve as etapas para a produção de um mapa típico (simulado) e os testes preliminares de um algoritmo para remover ruídos do tipo 1/f introduzidos pela estratégia de observação sem prejudicar a qualidade do sinal cosmológico presente no mapa.

Proton irradiation studies on Al and Al5083 alloy

NASA Astrophysics Data System (ADS)

Bhattacharyya, P.; Gayathri, N.; Bhattacharya, M.; Gupta, A. Dutta; Sarkar, Apu; Dhar, S.; Mitra, M. K.; Mukherjee, P.

2017-10-01

The change in the microstructural parameters and microhardness values in 6.5 MeV proton irradiated pure Al and Al5083 alloy samples have been evaluated using different model based techniques of X-ray diffraction Line Profile Analysis (XRD) and microindendation techniques. The detailed line profile analysis of the XRD data showed that the domain size increases and saturates with irradiation dose both in the case of Al and Al5083 alloy. The corresponding microstrain values did not show any change with irradiation dose in the case of the pure Al but showed an increase at higher irradiation doses in the case of Al5083 alloy. The microindendation results showed that unirradiated Al5083 alloy has higher hardness value compared to that of unirradiated pure Al. The hardness increased marginally with irradiation dose in the case of Al5083, whereas for pure Al, there was no significant change with dose.

Combustion synthesis of AlB2-Al2O3 composite powders with AlB2 nanowire structures

NASA Astrophysics Data System (ADS)

Yang, Pan; Xiao, Guoqing; Ding, Donghai; Ren, Yun; Yang, Shoulei; Lv, Lihua; Hou, Xing

2018-05-01

Using of Al and B2O3 powders as starting materials, and Mg-Al alloy as additives, AlB2-Al2O3 composite powders with AlB2 nanowire structures were successfully fabricated via combustion synthesis method in Ar atmosphere at a pressure of 1.5 MPa. The effect of different amount of Mg-Al alloy on the phase compositions and morphology of the combustion products was investigated. The results revealed that AlB2 and Al2O3 increased, whereas Al decreased with the content of Mg-Al alloy increasing. The impurities MgAl2O4 and AlB12 would exist in the sample with adding of 18 wt% Mg-Al alloy. Interestingly, FESEM/TEM/EDS results showed that AlB2 nanowires were observed in the products when the content of Mg-Al alloy is 6 wt% and 12 wt%. The more AlB2 nanowires can be found as the content of Mg-Al alloy increased. And the yield of AlB2 nanowires with the diameter of about 200 nanometers (nm) and the length up to several tens of micrometers (μm) in the combustion product is highest when the content of Mg-Al alloy is 12 wt%. The vapor, such as Mg-Al (g), B2O2 (g), AlO (g) and Al2O (g), produced during the process of combustion synthesis, reacted with each other to yield AlB2 nanowires by vapor-solid (VS) mechanism and the corresponding model was also proposed.

Interfacial Phenomena in Al/Al, Al/Cu, and Cu/Cu Joints Soldered Using an Al-Zn Alloy with Ag or Cu Additions

NASA Astrophysics Data System (ADS)

Pstruś, Janusz; Gancarz, Tomasz

2014-05-01

The studies of soldered joints were carried out in systems: Al/solder/Al, Al/solder/Cu, Cu/solder/Cu, where the solder was (Al-Zn)EUT, (Al-Zn)EUT with 0.5, 1.0, and 1.5 at.% of Ag and (Al-Zn)EUT with 0.5, 1.0, and 1.5 at.% of Cu addition. Brazing was performed at 500 °C for 3 min. The EDS analysis indicated that the composition of the layers starting from the Cu pad was CuZn, Cu5Zn8, and CuZn4, respectively. Wetting tests were performed at 500 °C for 3, 8, 15, and 30 min, respectively. Thickness of the layers and their kinetics of growth were measured based on the SEM micrographs. The formation of interlayers was not observed from the side of Al pads. On the contrary, dissolution of the Al substrate and migration of Al-rich particles into the bulk of the solder were observed.

Orientation relationship of eutectoid FeAl and FeAl2.

PubMed

Scherf, A; Kauffmann, A; Kauffmann-Weiss, S; Scherer, T; Li, X; Stein, F; Heilmaier, M

2016-04-01

Fe-Al alloys in the aluminium range of 55-65 at.% exhibit a lamellar microstructure of B2-ordered FeAl and triclinic FeAl 2 , which is caused by a eutectoid decomposition of the high-temperature Fe 5 Al 8 phase, the so-called ∊ phase. The orientation relationship of FeAl and FeAl 2 has previously been studied by Bastin et al. [ J. Cryst. Growth (1978 ▸), 43 , 745] and Hirata et al. [ Philos. Mag. Lett. (2008 ▸), 88 , 491]. Since both results are based on different crystallographic data regarding FeAl 2 , the data are re-evaluated with respect to a recent re-determination of the FeAl 2 phase provided by Chumak et al. [ Acta Cryst. (2010 ▸), C 66 , i87]. It is found that both orientation relationships match subsequent to a rotation operation of 180° about a 〈112〉 crystallographic axis of FeAl or by applying the inversion symmetry of the FeAl 2 crystal structure as suggested by the Chumak data set. Experimental evidence for the validity of the previously determined orientation relationships was found in as-cast fully lamellar material (random texture) as well as directionally solidified material (∼〈110〉 FeAl || solidification direction) by means of orientation imaging microscopy and global texture measurements. In addition, a preferential interface between FeAl and FeAl 2 was identified by means of trace analyses using cross sectioning with a focused ion beam. On the basis of these habit planes the orientation relationship between the two phases can be described by ([Formula: see text]01) FeAl || (114)[Formula: see text] and [111] FeAl || [1[Formula: see text]0][Formula: see text]. There is no evidence for twinning within FeAl lamellae or alternating orientations of FeAl lamellae. Based on the determined orientation and interface data, an atomistic model of the structure relationship of Fe 5 Al 8 , FeAl and FeAl 2 in the vicinity of the eutectoid decomposition is derived. This model is analysed with respect to the strain which has to be

Laboratory Evaluation of Multiviscosity-Grade Engine Oils in U.S. Army Diesel Engines

DTIC Science & Technology

1981-05-01

0.001 0.007 - 0.007 A-14 C L U 0i L zw 0 200 Lu 0 0- 0 ~~ U.’ L L u, C𔃾 H~~~( I - --- d z r- 8 0 0 0 r n CD 00 c z ’Uz 2 C3 ,’U tD z~ *C( 0% UJZ us...fl- ~ r %0 IT It r H- c c.0I I IHq * cI n CV 00r)0C) (n C ’OC4 C’JC.4 c 1-1 Ln 100 M0 0o 130 U 000 00 -- 13.6 30 L-6 TEST 3 9.1 ~ 20 LUBRICANT: AL...ARMOR SCHOOL ATTN ATSB- TD FORT KNOX KY 40121 Page 3 of 5 CDR DEPARTMENT OF THE NAVY US ARMY LOGISTICS CTR HQ, US HARINE CORPS ATTN ATCL-MS (MR A MARSHALL

U- and Th-Series Transport in a Sandy Aquifer in an Arid Climate

NASA Astrophysics Data System (ADS)

Reynolds, B. C.; Wasserburg, G. J.

2001-12-01

We investigated the transport of U-Th series nuclides of an aquifer in an arid region with low flow velocities, the Ojo Alamo Aquifer of the San Juan Basin, which has 14C water ages up to 25 kyr (Phillips et al. 1989; Stute et al. 1995). The study aims to test a theoretical transport model by Tricca et al. (2000) with data from an aquifer with lower groundwater flow velocities (4*E-6 cms-1 compared to 10-4 cms-1). U, Th, Ra and Rn activities and major ion abundances were analysed. Compared to the previous study, groundwaters have high U concentrations (CU ~ 20-200 ppt) and very high δ 234U values from 5,000 to 11,000. The CU of spring and river waters are much higher (0.7 to 12 ppb). The δ 234U values range from 500 to 700, far lower than the groundwaters. The present vadose and river water thus are completely distinctive from the aquifer water, and cannot be a significant source to the aquifer (<<10%). Estimating the groundwater age using the flow distance, an average weathering rate of U within the aquifer is calculated. These estimated rates vary between 10-18 to 10-16 s-1. The model predicts that δ 234U values depend upon the fraction of recoil 234Th ejected from the rock compared to the weathering rate. The high δ 234U values can easily be produced with low recoil fractions of 10-4 to 10-2. Applying the same model to a vadose zone thickness of 20 meters, with water infiltration rates of half the rainfall (22 cm/yr) and soil moisture contents around 10%, it is found that weathering rates and the recoil fraction are much higher in the vadose zone. Very high CU in the springs are caused by low infiltration rates through a vadose zone with low moisture content, and rapid weathering of smaller mineral grains in the soils. Lower CU in the groundwater indicate a disconnection between the spring waters and the rest of the groundwater, or that the high CU measured from the springs are contaminated (from an unknown source). Filtered CTh are less than 0.3 ppt. The

Advances in single mode and high power AlGaInN laser diode technology for systems applications

NASA Astrophysics Data System (ADS)

Najda, Stephen P.; Perlin, Piotr; Suski, Tadek; Marona, Lujca; Boćkowski, Michal; Leszczyński, Mike; Wisniewski, Przemek; Czernecki, Robert; Kucharski, Robert; Targowski, Grzegorz; Smalc-Koziorowska, Julita; Stanczyk, Szymon; Watson, Scott; Kelly, Antony E.

2015-03-01

The AlGaInN material system allows for laser diodes to be fabricated over a very wide range of wavelengths from u.v., ~380nm, to the visible ~530nm, by tuning the indium content of the laser GaInN quantum well. Thus AlGaInN laser diode technology is a key enabler for the development of new disruptive system level applications in displays, telecom, defence and other industries.

Southeastern U.S.A. Continental Shelf Respiratory Rates Revisited

NASA Technical Reports Server (NTRS)

Sheldon, Joan E.; Griffith, Peter C.; Peters Francesc; Sheldon, Wade M., Jr.; Blanton, Jackson O.; Amft, Julie; Pomeroy, Lawrence R.

2010-01-01

Respiratory rates on the U. S. southeastern continental shelf have been estimated several times by different investigators, most recently by Jiang et al. (Biogeochemistry 98:101-113, 2010) who report lower mean rates thanwere found in earlier work and attribute the differences to analytical error in all methods used in earlier studies. The differences are, instead, attributable to the differences in the geographical scope of the studies. The lower estimates of regional organic carbon flux of Jiang et al. (Biogeochemistry 98:101-113, 2010) are a consequence of their extrapolation of data from a small portion of the shelf to the entire South Atlantic Bight. This comment examines the methodologies used as well as the variability of respiratory rates in this region over space and time.

Ohmic contacts to Al-rich AlGaN heterostructures

DOE PAGES

Douglas, E. A.; Reza, S.; Sanchez, C.; ...

2017-06-06

Due to the ultra-wide bandgap of Al-rich AlGaN, up to 5.8 eV for the structures in this study, obtaining low resistance ohmic contacts is inherently difficult to achieve. A comparative study of three different fabrication schemes is presented for obtaining ohmic contacts to an Al-rich AlGaN channel. Schottky-like behavior was observed for several different planar metallization stacks (and anneal temperatures), in addition to a dry-etch recess metallization contact scheme on Al 0.85Ga 0.15N/Al 0.66Ga 0.34N. However, a dry etch recess followed by n +-GaN regrowth fabrication process is reported as a means to obtain lower contact resistivity ohmic contacts onmore » a Al 0.85Ga 0.15N/Al 0.66Ga 0.34N heterostructure. In conclusion, specific contact resistivity of 5×10 -3 Ω cm 2 was achieved after annealing Ti/Al/Ni/Au metallization.« less

Growth and stress-induced transformation of zinc blende AlN layers in Al-AlN-TiN multilayers

DOE PAGES

Li, Nan; Yadav, Satyesh K.; Wang, Jian; ...

2015-12-18

We report that AlN nanolayers in sputter deposited {111}Al/AlN/TiN multilayers exhibit the metastable zinc-blende-structure (z-AlN). Based on density function theory calculations, the growth of the z-AlN is ascribed to the kinetically and energetically favored nitridation of the deposited aluminium layer. In situ nanoindentation of the as-deposited {111}Al/AlN/TiN multilayers in a high-resolution transmission electron microscope revealed the z-AlN to wurzite AlN phase transformation through collective glide of Shockley partial dislocations on every two {111} planes of the z-AlN.

Assessment of calcium addition on the removal of U(VI) in the alkaline conditions created by NH 3 gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katsenovich, Yelena; Cardona, Claudia; Szecsody, Jim

Remediation of uranium (U) contamination in the deep vadose zone (VZ) sediments abundant in calcite mineral is a challenging task considering the formation of highly stable and mobile uranyl complexes with carbonate and calcium in pore water composition. There is a concern that uranium contamination in the VZ can serve as a continued source for groundwater pollution, creating a risk to human health and the environment through the groundwater pathway. This requires in-situ remediation of the radionuclide-contaminated VZ to convert soluble U species to low solubility precipitates that are stable in the natural environment. Injection of reactive gasses (e.g., NHmore » 3) is a promising technology to decrease U mobility in the unsaturated zone without the addition of liquid amendments. The NH 3 injection creates alkaline conditions that can alter the sediment pore water composition due to a release of elements from minerals (via desorption and dissolution) that are present in the sediment. However, it is not known how VZ pore water constituents (Si, Al 3+, HCO 3 -, and Ca 2 +) would affect U(VI) removal/precipitation in alkaline conditions. This study quantified the role of major pore water constituents typically present in the arid and semi-arid environments of the western regions of the U.S and identified solid uranium-bearing phases that could potentially precipitate from solutions approximating pore water compositions after pH manipulations via ammonia gas injections. Triplicate samples were prepared using six Si (5, 50 100, 150, 200, and 250 mM), six HCO 3 - (0, 3, 25, 50, 75, and 100 mM), and two Ca 2+ (5 and 10 mM) concentrations. The concentration of aluminum and uranium was kept constant at 5 mM and 0.0084 mM, respectively, in all synthetic formulations tested. Results showed that the percentage of U(VI) removal was controlled by the Si/Al molar ratios and Ca 2+ concentrations. Regardless of the bicarbonate concentration tested, the percentage of U

Assessment of calcium addition on the removal of U(VI) in the alkaline conditions created by NH 3 gas

DOE PAGES

Katsenovich, Yelena; Cardona, Claudia; Szecsody, Jim; ...

2018-03-06

Remediation of uranium (U) contamination in the deep vadose zone (VZ) sediments abundant in calcite mineral is a challenging task considering the formation of highly stable and mobile uranyl complexes with carbonate and calcium in pore water composition. There is a concern that uranium contamination in the VZ can serve as a continued source for groundwater pollution, creating a risk to human health and the environment through the groundwater pathway. This requires in-situ remediation of the radionuclide-contaminated VZ to convert soluble U species to low solubility precipitates that are stable in the natural environment. Injection of reactive gasses (e.g., NHmore » 3) is a promising technology to decrease U mobility in the unsaturated zone without the addition of liquid amendments. The NH 3 injection creates alkaline conditions that can alter the sediment pore water composition due to a release of elements from minerals (via desorption and dissolution) that are present in the sediment. However, it is not known how VZ pore water constituents (Si, Al 3+, HCO 3 -, and Ca 2 +) would affect U(VI) removal/precipitation in alkaline conditions. This study quantified the role of major pore water constituents typically present in the arid and semi-arid environments of the western regions of the U.S and identified solid uranium-bearing phases that could potentially precipitate from solutions approximating pore water compositions after pH manipulations via ammonia gas injections. Triplicate samples were prepared using six Si (5, 50 100, 150, 200, and 250 mM), six HCO 3 - (0, 3, 25, 50, 75, and 100 mM), and two Ca 2+ (5 and 10 mM) concentrations. The concentration of aluminum and uranium was kept constant at 5 mM and 0.0084 mM, respectively, in all synthetic formulations tested. Results showed that the percentage of U(VI) removal was controlled by the Si/Al molar ratios and Ca 2+ concentrations. Regardless of the bicarbonate concentration tested, the percentage of U

Electron capture by U(91+) and U(92+) and ionization of U(90+) and U(91+)

NASA Technical Reports Server (NTRS)

Gould, H.; Greiner, D.; Lindstrom, P.; Symons, T. J. M.; Crawford, H.

1984-01-01

U(92+)/U(91+) and U(91+)/U(90+) electron-capture and ionization cross sections and equilibrium charge-state distributions are measured experimentally in mylar, Cu and Ta of varying thickness. Relativistic U(68+) ions at 437 or 962 MeV/nucleon are produced by a heavy-ion linear accelerator and synchrotron in tandem and passed through the target material into a magnetic specrometer and position-sensitive proportional counter for evaluation of charge states. The results are presented graphically and discussed. At 962 MeV/nucleon, beams containing 85 percent bare U(92+) nuclei are obtained using 150-mg/sq cm Cu or 85-mg/sq cm Ta; at 437 MeV/nucleon, 50 percent bare U(92+) nuclei are obtained with 90-mg/sq cm Cu. The techniques decribed can be applied to produce beams of bare U nuclei for acceleration to ultrarelativistic speeds or beams of few-electron U for atomic-physics experiments on quantum electrodynamics.

Gore proposes doubling U.S. effort for global programs.

PubMed

1999-08-06

To confront the widespread HIV crisis, Vice President Al Gore has proposed a plan for doubling the current U.S. allocations for global programs. Seventy percent of the projected $100 million is earmarked for sub-Saharan Africa, with smaller portions going to Asia and former Soviet republics. The global campaign will address issues including containment, prevention and education efforts, and medical and psychological treatment programs. Several meetings are being scheduled with political leaders, industry, AIDS activists, and foreign leaders to address worldwide problems related to HIV. Most advocacy groups are praising the initiative, stating the U.S. is now recognizing HIV as a foreign policy priority. However, other groups are critical, and state that more funds are needed to effectively address this issue.

Constituent Redistribution in U-Zr Metallic Fuel Using the Advanced Fuel Performance Code BISON

DOE Office of Scientific and Technical Information (OSTI.GOV)

Galloway, Jack D.; Unal, Cetin; Matthews, Christopher

2016-09-30

Previous work done by Galloway, et. al. on EBR-II ternary (U-Pu-Zr) fuel constituent redistribution yielded accurate simulation data for the limited data sets of Zr redistribution. The data sets included EPMA scans of two different irradiated rods. First, T179, which was irradiated to 1.9 at% burnup, was analyzed. Second, DP16, which was irradiated to 11 at% burnup, was analyzed. One set of parameters that most accurately represented the zirconium profiles for both experiments was determined. Since the binary fuel (U-Zr) has previously been used as the driver fuel for sodium fast reactors (SFR) as well as being the likely drivermore » fuel if a new SFR is constructed, this same process has been initiated on the binary fuel form. From limited binary EPMA scans as well as other fuel characterization techniques, it has been observed that zirconium redistribution also occurs in the binary fuel, albeit at a reduced rate compared to observation in the ternary fuel, as noted by Kim et. al. While the rate of redistribution has been observed to be slower, numerous metallographs of U-Zr fuel show distinct zone formations.« less

Cobertura de los sistemas de pensiones y factores asociados al acceso a una pensión de jubilación en México

PubMed Central

Murillo-López, Sandra; Venegas-Martínez, Francisco

2016-01-01

Resumen Objetivos: obtener estimaciones de indicadores de cobertura de las pensiones por jubilación o retiro para la población mexicana de 65 y más años, y evaluar el impacto que tienen los sistemas de pensiones en las transiciones al retiro de los adultos en edades medias y avanzadas en México. Para ello se utilizan datos microeconómicos provenientes de la Encuesta Nacional de Salud y Envejecimiento. Mediante análisis econométrico se identifican los factores sociodemográficos, económicos, laborales e institucionales que están asociados al acceso a una pensión de jubilación, o bien, a la dependencia de otras fuentes de ingresos. Se encontró que, en México, las transiciones al retiro del mercado de trabajo en las etapas avanzadas del ciclo de vida son limitadas debido a las características eminentemente contributivas de los esquemas de pensiones, los cuales favorecen a la población con trayectorias laborales formales y más estables asociadas a: características de género, oportunidades educativas y posibilidades de inserción en el mercado laboral. PMID:27524936

Comparing the Thermodynamic Behaviour of Al(1)+ZrO2(s) to Al(1)+Al2O3(s)

NASA Technical Reports Server (NTRS)

Copland, Evan

2004-01-01

In an effort to better determine the thermodynamic properties of Al(g) and Al2O(g). the vapor in equilibrium with Al(l)+ZrO2(s) was compared to the vapor in equilibrium with Al(l)+Al2O3(s) over temperature range 1197-to-1509K. The comparison was made directly by Knudsen effusion-cell mass spectrometry with an instrument configured for a multiple effusion-cell vapor source (multi-cell KEMS). Second law enthalpies of vaporization of Al(g) and Al2O(g) together with activity measurements show that Al(l)+ZrO2(s) is thermodynamically equivalent to Al(l)+Al2O3(s), indicating Al(l) remained pure and Al2O3(s) was present in the ZrO2-cell. Subsequent observation of the Al(l)/ZrO2 and vapor/ZrO2 interfaces revealed a thin Al2O3-layer had formed, separating the ZrO2-cell from Al(l) and Al(g)+Al2O(g), effectively transforming it into an Al2O3 effusion-cell. This behavior agrees with recent observations made for Beta-NiAl(Pt) alloys measured in ZrO2 effusion-cell.

Simulating Asymmetric Top Impurities in Superfluid Clusters: A para-Water Dopant in para-Hydrogen.

PubMed

Zeng, Tao; Li, Hui; Roy, Pierre-Nicholas

2013-01-03

We present the first simulation study of bosonic clusters doped with an asymmetric top molecule. The path-integral Monte Carlo method with the latest methodological advance in treating rigid-body rotation [Noya, E. G.; Vega, C.; McBride, C. J. Chem. Phys.2011, 134, 054117] is employed to study a para-water impurity in para-hydrogen clusters with up to 20 para-hydrogen molecules. The growth pattern of the doped clusters is similar in nature to that of pure clusters. The para-water molecule appears to rotate freely in the cluster. The presence of para-water substantially quenches the superfluid response of para-hydrogen with respect to the space-fixed frame.

Walnut twig beetle: update on the biology and chemical ecology of a vector of an invasive fatal disease of walnut in the western U.S.

Treesearch

Steven J. Seybold; Andrew D. Graves; Tom W. Coleman

2011-01-01

The walnut twig beetle, Pityophthorus juglandis Blackman (Coleoptera: Scolytidae) (sensu Wood 2007), is a native North American bark beetle that has been recently implicated as the vector of thousand cankers disease of walnut trees in the western U.S. (Tisserat et al. 2009, Utley et al. 2009, Seybold et al. 2010).

Laser ablation U-Th-Sm/He dating of detrital apatite

NASA Astrophysics Data System (ADS)

Guest, B.; Pickering, J. E.; Matthews, W.; Hamilton, B.; Sykes, C.

2016-12-01

Detrital apatite U-Th-Sm/He thermochronology has the potential to be a powerful tool for conducting basin thermal history analyses as well as complementing the well-established detrital zircon U-Pb approach in source to sink studies. A critical roadblock that prevents the routine application of detrital apatite U-Th-Sm/He thermochronology to solving geological problems is the costly and difficult whole grain approach that is generally used to obtain apatite U-Th-Sm/He data. We present a new analytical method for laser ablation thermochronology on apatite. Samples are ablated using a Resonetics™ 193 nm excimer laser and liberated 4He is measured using an ASI (Australian Scientific Instruments) Alphachron™ quadrupole mass spectrometer system; collectively known as the Resochron™. The ablated sites are imaged using a Zygo ZescopeTM optical profilometer and ablated pit volume measured using PitVol, a custom MatLabTM algorithm. The accuracy and precision of the method presented here was confirmed using well-characterized Durango apatite and Fish Canyon Tuff (FCT) apatite reference materials, with Durango apatite used as a primary reference and FCT apatite used as a secondary reference. The weighted average of our laser ablation Durango ages (30.5±0.35 Ma) compare well with ages obtained using conventional whole grain degassing and dissolution U-Th-Sm/He methods (32.56±0.43 Ma) (Jonckheere et.al., 1 993; Farley, 2000; McDowell et.al., 2005) for chips of the same Durango crystal. These Durango ages were used to produce a K-value to correct the secondary references and unknown samples. After correction, FCT apatite has a weighted average age of 28.37 ± 0.96 Ma, which agrees well with published ages. As a further test of this new method we have conducted a case study on a set of samples from the British Mountains of the Yukon Territory in NW Canada. Sandstone samples collected across the British Mountains were analyzed using conventional U-Th-Sm/He whole grain

Nanoporous Al sandwich foils using size effect of Al layer thickness during Cu/Al/Cu laminate rolling

NASA Astrophysics Data System (ADS)

Yu, Hailiang; Lu, Cheng; Tieu, A. Kiet; Li, Huijun; Godbole, Ajit; Kong, Charlie

2018-06-01

The roll bonding technique is one of the most widely used methods to produce metal laminate sheets. Such sheets offer interesting research opportunities for both scientists and engineers. In this paper, we report on an experimental investigation of the 'thickness effect' during laminate rolling for the first time. Using a four-high multifunction rolling mill, Cu/Al/Cu laminate sheets were fabricated with a range of thicknesses (16, 40, 70 and 130 μm) of the Al layer. The thickness of the Cu sheets was a constant 300 μm. After rolling, TEM images show good bonding quality between the Cu and Al layers. However, there are many nanoscale pores in the Al layer. The fraction of nanoscale pores in the Al layer increases with a reduction in the Al layer thickness. The finite element method was used to simulate the Cu/Al/Cu rolling process. The simulation results reveal the effect of the Al layer thickness on the deformation characteristics of the Cu/Al/Cu laminate. Finally, we propose that the size effect of the Al layer thickness during Cu/Al/Cu laminate rolling may offer a method to fabricate 'nanoporous' Al sandwich laminate foils. Such foils can be used in electromagnetic shielding of electrical devices and noisy shielding of building.

Element-specific observation of the ferromagnetic ordering process in UCoAl via soft x-ray magnetic circular dichroism

NASA Astrophysics Data System (ADS)

Takeda, Yukiharu; Saitoh, Yuji; Okane, Tetsuo; Yamagami, Hiroshi; Matsuda, Tatsuma D.; Yamamoto, Etsuji; Haga, Yoshinori; Ōnuki, Yoshichika

2018-05-01

We have performed soft x-ray magnetic circular dichroism (XMCD) experiments on the itinerant-electron metamagnet UCoAl at the U 4 d -5 f (N4 ,5) and Co 2 p -3 d (L2 ,3) absorption edges in order to investigate the magnetic properties of the U 5 f and Co 3 d electrons separately. From the line shape of the XMCD spectrum, it is deduced that the orbital magnetic moment of the Co 3 d electrons is unusually large. Through the systematic temperature (T )- and magnetic field (H )-dependent XMCD measurements, we have obtained two types of the magnetization curve as a function of H and T (M-H curve and M-T curve, respectively). The metamagnetic transition from a paramagnetic state to a field-induced ferromagnetic state was clearly observed under 15 K at HM. The value of the HM and its T dependence agree well between the U and Co sites, and the bulk magnetization. Whereas, we have discovered the remarkable differences in the M-H and M-T curves between the U and Co sites. The present findings clearly show that the role of the Co 3 d electrons should be considered more carefully in order to understand the origin of the magnetic ordering in UCoAl.

Concentration and emission sources of airborne metals in particulate matter in the industrial district of Médio Paraíba, state of Rio de Janeiro, Brazil.

PubMed

Loyola, Josiane; de Almeida, Pierre Batista; Quiterio, Simone Lorena; Sousa, Célia Regina; Arbilla, Graciela; Escaleira, Viviane; de Carvalho, Maria Isabel; dos Santos Amaral Gomes da Silva, Alzira

2006-11-01

Total suspended particles and 12 airborne metals were determined in 4 sampling sites in the industrial region of Médio Paraíba, Brazil. The geometrical means for the four sampling locals were (in units of microg/m3): 65.9 in Barra Mansa, 57.3 in Jardim Paraíba (Volta Redonda), 41.7 in Resende, and 48.9 in Volta Grande (Volta Redonda). These values are lower than levels previously determined in urban and industrial locals of the Metropolitan Area of Rio de Janeiro. For metals, the higher concentrations were obtained for Ca, Zn, Al, Fe, and Mg. Ca, Zn, and Al levels are higher than those determined in other industrial areas. These three metals are used in steel manufacturing, the main economical activity of the region. Enrichment factors for Zn, Cu, Cd, and Pb are higher than 10, suggesting an industrial input. Statistical analysis show a high correlation among Ca, Mg, Zn, Cr, Al, Mn, and Fe, all of them used as raw materials in steel manufacturing and/or accumulated as industrial blast furnace slag and steelworks slag.

Ti{sub 2}AlN thin films synthesized by annealing of (Ti+Al)/AlN multilayers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cabioch, Thierry, E-mail: Thierry.cabioch@univ-poitiers.fr; Alkazaz, Malaz; Beaufort, Marie-France

2016-08-15

Highlights: • Epitaxial thin films of the MAX phase Ti{sub 2}AlN are obtained by thermal annealing. • A new metastable (Ti,Al,N) solid solution with the structure of α-T is evidenced. • The formation of the MAX phase occurs at low temperature (600 °C). - Abstract: Single-phase Ti{sub 2}AlN thin films were obtained by annealing in vacuum of (Ti + Al)/AlN multilayers deposited at room temperature by magnetron sputtering onto single-crystalline (0001) 4H-SiC and (0001) Al{sub 2}O{sub 3} substrates. In-situ X-ray diffraction experiments combined with ex-situ cross-sectional transmission electron microscopy observations reveal that interdiffusion processes occur in the multilayer at amore » temperature of ∼400 °C leading to the formation of a (Ti, Al, N) solid solution, having the hexagonal structure of α-Ti, whereas the formation of Ti{sub 2}AlN occurs at 550–600 °C. Highly oriented (0002) Ti{sub 2}AlN thin films can be obtained after an annealing at 750 °C.« less

Distribution of U-Th nuclides in the riverine and coastal environments of the tropical southwest coast of India.

PubMed

Balakrishna, K; Shankar, R; Sarin, M M; Manjunatha, B R

2001-01-01

A reconnaissance study has been made on the distribution of 238U, 234U, 232Th and 230Th in soils, water, suspended particulate matter (SPM) and bottom sediments in the Kali river basin around Kaiga, its estuarine region and the adjacent Arabian Sea to obtain the baseline data of U-Th series nuclides in view of the commissioning of nuclear power reactors at Kaiga, near Karwar, on the southwest coast of India. Drainage basin soils developed over greywackes (the dominant litho-unit upstream) are lower in 238U/Al and 232Th/Al ratios by factors of 3-5 in comparison with those developed over tonalitic gneisses (the dominant litho-unit downstream). The dominance of the former type of soils is reflected in the composition of river-bottom sediments derived from the upstream drainage basin during the monsoon. The 232Th in bottom sediments tends to increase towards the estuarine and coastal areas, presumably due to deposition of heavy minerals and onshore transport of coastal sediments into the estuary. The dissolved U in the Kali river is low (0.001-0.02 microg/l) when compared to the major Indian rivers as the Kali river flows through U-poor greywackes. Thus, the input of dissolved U to the Kali estuary is dominated by sea water. Although there is some evidence for the removal of dissolved U at low salinity during estuarine mixing, its behaviour is conservative in the lower estuary (at higher salinities). The removal rate of dissolved U from the Kali river basin is similar to that reported from other tropical river basins. The U flux from all the west-flowing rivers of Peninsular India is estimated at 26.3 x 10(6) g/yr to the Arabian Sea which is about 2% of the flux from the Himalayan rivers to the Bay of Bengal.

Time-scale calibration by U-Pb geochronology: Examples from the Triassic Period

NASA Astrophysics Data System (ADS)

Mundil, R.

2009-05-01

)) and the Early-Middle Triassic (Olenekian-Anisian) boundary (247.2 Ma, (8, 9)), resulting in a surprisingly short duration of the Early Triassic which has implications for the timing of biotic recovery and major changes in ocean chemistry during this time. Furthermore, the Anisian-Ladinian boundary is constrained to 242.0 Ma by new U-Pb and 40Ar/39Ar ages. Radio-isotopic ages for the Late Triassic are scarce and the only reliable and biostratigraphically controlled age is from an upper Carnian tuff dated to 230.9 Ma (10), yielding a duration of more than 35 Ma for the Late Triassic. The resulting time-scale is at odds with the most recent compilation (11) but arguably more accurate because it is entirely based on U-Pb analyses applied to closed-system zircons with uncertainties at the permil level or better. 1. T. E. Krogh, Geochimica et Cosmochimica Acta 37, 485 (1973); 2. T. E. Krogh, Geochimica et Cosmochimica Acta 46, 637 (1982); 3. J. M. Mattinson, Chemical Geology 220, 47 (2005); 4. R. Mundil, K. R. Ludwig, I. Metcalfe, P. R. Renne, Science 305, 1760 (2004); 5. U. Schaltegger, J. Guex, A. Bartolini, B. Schoene, M. Ovtcharova, Earth and Planetary Science Letters 267, 266 (2008); 6. R. Mundil, P. R. Renne, K. K. Min, K. R. Ludwig, in Eos Trans. AGU, Fall Meet. Suppl. (2006), vol. 87(52), pp. V21A-0543; 7. T. Galfetti et al., Earth and Planetary Science Letters 258, 593 (2007). 8. M. Ovtcharova et al., Earth and Planetary Science Letters 243, 463 (2006). 9. J. Ramezani et al., Earth and Planetary Science Letters 256, 244 (2007). 10. S. Furin et al., Geology 34, 1009 (2006); 11. J. G. Ogg, in A Geologic Time Scale 2004 F. M. Gradstein, J. G. Ogg, A. G. Smith, Eds. (University Press, Cambridge, 2004) pp. 271-306.

Comment on “Historical perspective on seismic hazard to Hispaniola and the northeast Caribbean region” by U. ten Brink et al.

USGS Publications Warehouse

Prentice, Carol S.; Mann, Paul; Peña, Luis R.

2013-01-01

The analysis of historical earthquakes in the northeastern Caribbean by ten Brink et al. [2011, hereafter TB11] addresses the occurrence of large and destructive historical earthquakes associated with the North American-Caribbean plate boundary. One conclusion presented in TB11 is that the recurrence interval for large earthquakes on the left-lateral, strike-slip Septentrional Fault (SF) (Figure 1a) is approximately 300 years. Their Figure 7 shows rupture of the SF across the entire island of Hispaniola in CE 1200, 1542, and 1842. Our comment challenges this model for SF earthquake recurrence because it is inconsistent with our published paleoseismic data that show no large historical earthquake is associated with surface rupture along the SF east of Santiago (Figure 1a)[Prentice et al., 1993; Mann et al., 1998; Prentice et al., 2003].

Reinterpretation of femtosecond laser pump-probe and thermomodulation optical spectroscopy results on HTSC materials in terms of the resonant negative-U model

NASA Astrophysics Data System (ADS)

Wilson, John A.

2000-01-01

The laser pump/probe spectroscopy from Stevens et al (on YBCO7 ) and the thermomodulation optical data and analysis from Holcomb et al (on a selection of HTSC materials) are examined in terms of the resonant negative-U mechanism for high temperature superconductivity (HTSC) in the mixed-valent cuprates. The work centres on the universal 1.5-2 eV features becoming visible below Tc upon the optical `charge-transfer' edge. These it is argued are not simple p-to-d band-to-band excitations but are to be associated with the mixed-valent and negative-U states that instigate HTSC. This argument is supported both by the decay characteristics apparent in the new data recorded by Stevens et al and also in the outcome of the Eliashberg analysis developed by Holcomb et al to accommodate their own thermomodulation data. The interpretation provided is in line with that offered recently of the highly characteristic thermoelectric behaviour exhibited by all HTSC systems.

Diffusion Barrier Selection from Refractory Metals (Zr, Mo and Nb) via Interdiffusion Investigation for U-Mo RERTR Fuel Alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

K. Huang; C. Kammerer; D. D. Keiser, Jr.

2014-04-01

U-Mo alloys are being developed as low enrichment monolithic fuel under the Reduced Enrichment for Research and Test Reactor (RERTR) Program. Diffusional interactions between the U-Mo fuel alloy and Al-alloy cladding within the monolithic fuel plate construct necessitate incorporation of a barrier layer. Fundamentally, a diffusion barrier candidate must have good thermal conductivity, high melting point, minimal metallurgical interaction, and good irradiation performance. Refractory metals, Zr, Mo, and Nb are considered based on their physical properties, and the diffusion behavior must be carefully examined first with U-Mo fuel alloy. Solid-to-solid U-10wt.%Mo vs. Mo, Zr, or Nb diffusion couples were assembledmore » and annealed at 600, 700, 800, 900 and 1000 degrees C for various times. The interdiffusion microstructures and chemical composition were examined via scanning electron microscopy and electron probe microanalysis, respectively. For all three systems, the growth rate of interdiffusion zone were calculated at 1000, 900 and 800 degrees C under the assumption of parabolic growth, and calculated for lower temperature of 700, 600 and 500 degrees C according to Arrhenius relationship. The growth rate was determined to be about 10 3 times slower for Zr, 10 5 times slower for Mo and 10 6 times slower for Nb, than the growth rates reported for the interaction between the U-Mo fuel alloy and pure Al or Al-Si cladding alloys. Zr, however was selected as the barrier metal due to a concern for thermo- mechanical behavior of UMo/Nb interface observed from diffusion couples, and for ductile-to-brittle transition of Mo near room temperature.« less

Nano-Al Based Energetics: Rapid Heating Studies and a New Preparation Technique

NASA Astrophysics Data System (ADS)

Sullivan, Kyle; Kuntz, Josh; Gash, Alex; Zachariah, Michael

2011-06-01

Nano-Al based thermites have become an attractive alternative to traditional energetic formulations due to their increased energy density and high reactivity. Understanding the intrinsic reaction mechanism has been a difficult task, largely due to the lack of experimental techniques capable of rapidly and uniform heating a sample (~104- 108 K/s). The current work presents several studies on nano-Al based thermites, using rapid heating techniques. A new mechanism termed a Reactive Sintering Mechanism is proposed for nano-Al based thermites. In addition, new experimental techniques for nanocomposite thermite deposition onto thin Pt electrodes will be discussed. This combined technique will offer more precise control of the deposition, and will serve to further our understanding of the intrinsic reaction mechanism of rapidly heated energetic systems. An improved mechanistic understanding will lead to the development of optimized formulations and architectures. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Fixed dynamometry is more sensitive than vital capacity or ALS rating scale.

PubMed

Andres, Patricia L; Allred, Margaret Peggy; Stephens, Helen E; Proffitt Bunnell, Mary; Siener, Catherine; Macklin, Eric A; Haines, Travis; English, Robert A; Fetterman, Katherine A; Kasarskis, Edward J; Florence, Julaine; Simmons, Zachary; Cudkowicz, Merit E

2017-10-01

Improved outcome measures are essential to efficiently screen the growing number of potential amyotrophic lateral sclerosis (ALS) therapies. This longitudinal study of 100 (70 male) participants with ALS compared Accurate Test of Limb Isometric Strength (ATLIS), using a fixed, wireless load cell, with ALS Functional Rating Scale-Revised (ALSFRS-R) and vital capacity (VC). Participants enrolled at 5 U.S. sites. Data were analyzed from 66 participants with complete ATLIS, ALSFRS-R, and VC data over at least 3 visits. Change in ATLIS was less variable both within- and among-person than change in ALSFRS-R or VC. Additionally, participants who had normal ALSFRS-R arm and leg function averaged 12 to 32% below expected strength values measured by ATLIS. ATLIS was more sensitive to change than ALSFRS-R or VC and could decrease sample size requirements by approximately one-third. The ability of ATLIS to detect prefunctional change has potential value in early trials. Muscle Nerve 56: 710-715, 2017. © 2017 Wiley Periodicals, Inc.

Aplicación de la metodología Molecular de Orbitales de Defecto Cuántico (MQDO) al cálculo de intensidades vibrónicas y vidas medias de niveles vibracionales

NASA Astrophysics Data System (ADS)

María Velasco Sanz, Ana

Desde que se formuló, en 1996, la metodología Molecular de Orbitales de Defecto Cuántico (MQDO) [1], se han obtenido datos de calidad relativos a intensidades de bandas electrónicas que implican estados Rydberg para una gran variedad de sistemas moleculares [2]. Animados por los buenos resultados obtenidos, recientemente hemos abordado el estudio de transiciones vibrónicas, es decir aquellas que ocurren entre estados vibracionales que pertenecen a distintos estados Rydberg electrónicos. Como prototipo adecuado para nuestros propósitos hemos elegido la molécula de NO, importante en la química de la atmósfera, y para la cual existen en la bibliografía datos experimentales de calidad suficiente para contrastar la validez de nuestros resultados. En concreto, hemos calculado las fuerzas de oscilador y coeficientes de Einstein para transiciones electrónicas y vibrónicas de las principales bandas del NO, al igual que vidas medias radiativas de niveles vibracionales de dicha molécula. Las propiedades estudiadas son esenciales para la comprensión de los aspectos teóricos de los procesos físicos básicos relativos a la dispersión electrónica en moléculas heteronucleares con capas abiertas. Además, valores fiables de probabilidades de transición moleculares tienen importantes aplicaciones en Astrofísica, en la modelización de procesos fotodinámicos moleculares, etc., al igual que para evaluar más profundamente la validez de nuestra metodología teórica.

[Determination of 235U/238U isotope ratios in camphor tree bark samples by MC-ICP-MS after separation of uranium from matrix elements].

PubMed

Wang, Xiao-Ping; Zhang, Ji-Long

2007-07-01

Twelve camphor (cinnamomum camphora) tree bark samples were collected from Hiroshima and Kyoto, and the matrix element composition and morphology of the outer surface of these camphor tree bark samples were studied by EDXS and SEM respectively. After a dry decomposition, DOWEX 1-X8 anion exchange resin was used to separate uranium from matrix elements in these camphor tree bark samples. Finally, 235U/238 U isotope ratios in purified uranium solutions were determined by MC-ICP-MS. It was demonstrated that the outer surface of these camphor tree bark samples is porous and rough, with Al, Ca, Fe, K, Mg, Si, C, O and S as its matrix element composition. Uranium in these camphor tree bark samples can be efficiently separated and quantitatively recovered from the matrix element composition. Compared with those collected from Kyoto, the camphor tree bark samples collected from Hiroshima have significantly higher uranium contents, which may be due to the increased aerosol mass concentration during the city reconstruction. Moreover, the 235 U/23.U isotope ratios in a few camphor tree bark samples collected from Hiroshima are slightly higher than 0.007 25.

Ab initio calculation of atomic interactions on Al(110): implications for epitaxial growth

NASA Astrophysics Data System (ADS)

Fichthorn, Kristen; Tiwary, Yogesh

2007-03-01

Using first-principles calculations based on density-functional theory, we resolved atomic interactions between adsorbed Al atoms on Al(110). Relevant pair and trio interactions were quantified. We find that pair interactions extend to the third in-channel and second cross-channel neighbor on the anisotropic (110) surface. Beyond these distances, pair interactions are negligible. The nearest-neighbor interaction in the in-channel direction is attractive, but nearest-neighbor cross-channel interaction is repulsive. While nearest-neighbor, cross-channel repulsion does not support the experimental observation of 3D hut formation in Al/Al(110) homoepitaxial growth [1], we find that trio interactions can be significant and attractive and they support cross-channel bonding. The pair and trio interactions have direct and indirect components. We have quantified the electronic and elastic components of the indirect, substrate-mediated interactions. We also probe the influence of these interactions on the energy barriers for adatom hopping. [1] F. Buatier de Mongeot, W. Zhu, A. Molle, R. Buzio, C. Boragno, U. Valbusa, E. Wang, and Z. Zhang, Phys. Rev. Lett. 91, 016102 (2003).

Effect of AlCl3 concentration on nanoparticle removal by coagulation.

PubMed

Zhang, Lizhu; Mao, Jingchun; Zhao, Qing; He, Shaobo; Ma, Jun

2015-12-01

In recent years, engineered nanoparticles, as a new group of contaminants emerging in natural water, have been given more attention. In order to understand the behavior of nanoparticles in the conventional water treatment process, three kinds of nanoparticle suspensions, namely multi-walled carbon nanotube-humic acid (MWCNT-HA), multi-walled carbon nanotube-N,N-dimethylformamide (MWCNT-DMF) and nanoTiO2-humic acid (TiO2-HA) were employed to investigate their coagulation removal efficiencies with varying aluminum chloride (AlCl3) concentrations. Results showed that nanoparticle removal rate curves had a reverse "U" shape with increasing concentration of aluminum ion (Al(3+)). More than 90% of nanoparticles could be effectively removed by an appropriate Al(3+) concentration. At higher Al(3+) concentration, nanoparticles would be restabilized. The hydrodynamic particle size of nanoparticles was found to be the crucial factor influencing the effective concentration range (ECR) of Al(3+) for nanoparticle removal. The ECR of Al(3+) followed the order MWCNT-DMF>MWCNT-HA>TiO2-HA, which is the reverse of the nanoparticle size trend. At a given concentration, smaller nanoparticles carry more surface charges, and thus consume more coagulants for neutralization. Therefore, over-saturation occurred at relatively higher Al(3+) concentration and a wider ECR was obtained. The ECR became broader with increasing pH because of the smaller hydrodynamic particle size of nanoparticles at higher pH values. A high ionic strength of NaCl can also widen the ECR due to its strong potential to compress the electric double layer. It was concluded that it is important to adjust the dose of Al(3+) in the ECR for nanoparticle removal in water treatment. Copyright © 2015. Published by Elsevier B.V.

ALS Association

MedlinePlus

... toward a world without ALS! Walk to Defeat ALS® Walk to Defeat ALS® draws people of all ... We need your help. I Will Advocate National ALS Registry The National ALS Registry is a congressionally ...

Expedition54_Education_In-flight_Para_Los_Ninos_053_1755_621343_hires

NASA Image and Video Library

2018-02-22

SPACE STATION CREW MEMBER DISCUSSES LIFE IN SPACE WITH HISPANIC STUDENTS IN LOS ANGELES:::::::: Aboard the International Space Station, Expedition 54 Flight Engineer Joe Acaba of NASA discussed his mission on the complex and life and research in space with students at the Para Los Ninos School in Los Angeles during an in-flight educational event Feb. 22. Acaba, who has been in orbit since last September, is returning to Earth on a Russian Soyuz spacecraft on Feb. 27 (U.S. time) for a landing in south central Kazakhstan.

Development of High-Activity Para- to Ortho-Hydrogen Conversion Catalysts. Volume 2

DTIC Science & Technology

1989-09-28

Proc. Roy. Soc. London AllO, 464 (1925). 2 1929 Para- and ortho-hydrogen, Barmois, E., La Nature No. 2820, 400-1 (1929) C.A. 24,, 1020b. K. F...U.S. At. Energy Comm. LA -2719, 40 pp. (1962); cf. 3. Chem. Eng. Data 7, 179(1962). C.A. 58, 10750g. Schmidt number for normal hydrogen and...A-L);- p 181-9; in Eng. Briones, A. G.; Garcia de la Banda, J. F.; Inst. Quim. Fis. Quim., Madrid, Anales Real. Soc. Espan. Fis. Quim. (Madrid); Ser

Field Application of 238U/235U Measurements To Detect Reoxidation and Mobilization of U(IV).

PubMed

Jemison, Noah E; Shiel, Alyssa E; Johnson, Thomas M; Lundstrom, Craig C; Long, Philip E; Williams, Kenneth H

2018-03-20

Biostimulation to induce reduction of soluble U(VI) to relatively immobile U(IV) is an effective strategy for decreasing aqueous U(VI) concentrations in contaminated groundwater systems. If oxidation of U(IV) occurs following the biostimulation phase, U(VI) concentrations increase, challenging the long-term effectiveness of this technique. However, detecting U(IV) oxidation through dissolved U concentrations alone can prove difficult in locations with few groundwater wells to track the addition of U to a mass of groundwater. We propose the 238 U/ 235 U ratio of aqueous U as an independent, reliable tracer of U(IV) remobilization via oxidation or mobilization of colloids. Reduction of U(VI) produces 238 U-enriched U(IV), whereas remobilization of solid U(IV) should not induce isotopic fractionation. The incorporation of remobilized U(IV) with a high 238 U/ 235 U ratio into the aqueous U(VI) pool produces an increase in 238 U/ 235 U of aqueous U(VI). During several injections of nitrate to induce U(IV) oxidation, 238 U/ 235 U consistently increased, suggesting 238 U/ 235 U is broadly applicable for detecting mobilization of U(IV).

U.S. EPA, Pesticide Product Label, PIC-BROM 33, 01/04/1984

EPA Pesticide Factsheets

2011-04-21

... " •• OM ••••• nn~.1 bh •• J ••••. l._ ... I""~ _ ... ~" l&.r;..~~r~ •••. tOt".J~J'"'' "u.dJI .• nd l. .... J'J".') f).I. t.:al'l"n~ I. r"a .It."uyo li" •. I' •• 11"". ...

Laser Ablation in situ (U-Th-Sm)/He and U-Pb Double-Dating of Apatite and Zircon: Techniques and Applications

NASA Astrophysics Data System (ADS)

McInnes, B.; Danišík, M.; Evans, N.; McDonald, B.; Becker, T.; Vermeesch, P.

2015-12-01

We present a new laser-based technique for rapid, quantitative and automated in situ microanalysis of U, Th, Sm, Pb and He for applications in geochronology, thermochronometry and geochemistry (Evans et al., 2015). This novel capability permits a detailed interrogation of the time-temperature history of rocks containing apatite, zircon and other accessory phases by providing both (U-Th-Sm)/He and U-Pb ages (+trace element analysis) on single crystals. In situ laser microanalysis offers several advantages over conventional bulk crystal methods in terms of safety, cost, productivity and spatial resolution. We developed and integrated a suite of analytical instruments including a 193 nm ArF excimer laser system (RESOlution M-50A-LR), a quadrupole ICP-MS (Agilent 7700s), an Alphachron helium mass spectrometry system and swappable flow-through and ultra-high vacuum analytical chambers. The analytical protocols include the following steps: mounting/polishing in PFA Teflon using methods similar to those adopted for fission track etching; laser He extraction and analysis using a 2 s ablation at 5 Hz and 2-3 J/cm2fluence; He pit volume measurement using atomic force microscopy, and U-Th-Sm-Pb (plus optional trace element) analysis using traditional laser ablation methods. The major analytical challenges for apatite include the low U, Th and He contents relative to zircon and the elevated common Pb content. On the other hand, apatite typically has less extreme and less complex zoning of parent isotopes (primarily U and Th). A freeware application has been developed for determining (U-Th-Sm)/He ages from the raw analytical data and Iolite software was used for U-Pb age and trace element determination. In situ double-dating has successfully replicated conventional U-Pb and (U-Th)/He age variations in xenocrystic zircon from the diamondiferous Ellendale lamproite pipe, Western Australia and increased zircon analytical throughput by a factor of 50 over conventional methods

The Effect of Microstructure on the Creep behavior of Ti-6Al-2Nb-1Ta-0.8Mo.

DTIC Science & Technology

1985-09-01

SCIENCE WI H MILLER El AL . SEP 85 UNLSSFEM N 1 -21 U m|hh|hhh|h|hEI mmhhhhhhmhhmml mh/|mhEEE/mhh EigEggEElgllgE * -72 °o- ° - 112.5 .b L. L.- 1111 34...transus temperature ( Al and interstitials 02, N2 and C) and "alpha strengthening elements which have high alpha soluability (Sn, Si and Zr) but do not...Ti 3 A1 may also precipitate in the alpha phase 3 and cause embrittlement in some alloy systems during ageing at 773K ( l.4) The effect of Ti 3 Al

Preliminary Results of National Amyotrophic Lateral Sclerosis (ALS) Registry Risk Factor Survey Data

PubMed Central

2016-01-01

Background The National ALS Registry is made up of two components to capture amyotrophic lateral sclerosis (ALS) cases: national administrative databases (Medicare, Medicaid, Veterans Health Administration and Veterans Benefits Administration) and self-identified cases captured by the Registry’s web portal. This study describes self-reported characteristics of U.S. adults with ALS using the data collected by the National ALS Registry web portal risk factor surveys only from October 19, 2010 through December 31, 2013. Objective To describe findings from the National ALS Registry’s web portal risk factor surveys. Measurements The prevalence of select risk factors among adults with ALS was determined by calculating the frequencies of select risk factors—smoking and alcohol (non, current and former) histories, military service and occupational history, and family history of neurodegenerative diseases such as ALS, Alzheimer’s and/or Parkinson’s. Results Nearly half of survey respondents were ever smokers compared with nearly 41% of adults nationally. Most respondents were ever drinkers which is comparable to national estimates. The majority were light drinkers. Nearly one-quarter of survey respondents were veterans compared with roughly 9% of US adults nationally. Most respondents were retired or disabled. The industries in which respondents were employed for the longest time were Professional and Scientific and Technical Services. When family history of neurodegenerative diseases in first degree relatives was evaluated against our comparison group, the rates of ALS were similar, but were higher for Parkinson’s disease, Alzheimer’s disease and any neurodegenerative diseases. Conclusions The National ALS Registry web portal, to our knowledge, is the largest, most geographically diverse collection of risk factor data about adults living with ALS. Various characteristics were consistent with other published studies on ALS risk factors and will allow

A comparative analysis of alpha-decay half-lives for even-even 178Pb to 234U isotopes

NASA Astrophysics Data System (ADS)

Hosseini, S. S.; Hassanabadi, H.; Zarrinkamar, S.

2018-02-01

The feasibility for the alpha decay from the even-even transitions of 178Pb to 234U isotopes has been studied within the Coulomb and proximity potential model (CPPM). The alpha decay half-lives are considered from different theoretical approaches using Semi-empirical formula of Poenaru et al. (SemFIS), the Universal Decay law (UDL) of Qi et al., Akrawy-Dorin formula of Akrawy and Poenaru (ADF), the Scaling law of Brown (SLB) and the Scaling Law of Horoi et al. (SLH). The numerical results obtained by the CPPM and compared with other method as well the experimental data.

U.S. President Richard Milhous Nixon Arrives Aboard U.S.S. Hornet for Apollo 11 Recovery

NASA Technical Reports Server (NTRS)

1969-01-01

U.S. President Richard Milhous Nixon (center), is saluted by the honor guard of flight deck crewmen when he arrives aboard the U.S.S. Hornet, prime recovery ship for the Apollo 11 mission, to watch recovery operations and welcome the astronauts home. The recovery operation took place in the Pacific Ocean where Navy para-rescue men recovered the capsule housing the 3-man Apollo 11 crew. The crew was airlifted to safety aboard the U.S.S. Hornet, where they were quartered in a Mobile Quarantine Facility (MQF) for 21 days following the mission. The Apollo 11 mission, the first manned lunar mission, launched from the Kennedy Space Center, Florida via the Saturn V launch vehicle on July 16, 1969 and safely returned to Earth on July 24, 1969. Aboard were Neil A. Armstrong, commander; Michael Collins, Command Module (CM) pilot; and Edwin E. Aldrin Jr., Lunar Module (LM) pilot. The CM, piloted by Michael Collins remained in a parking orbit around the Moon while the LM, named 'Eagle'', carrying astronauts Neil Armstrong and Edwin Aldrin, landed on the Moon. Armstrong was the first human to ever stand on the lunar surface, followed by Edwin (Buzz) Aldrin. During 2½ hours of surface exploration, the crew collected 47 pounds of lunar surface material for analysis back on Earth. With the success of Apollo 11, the national objective to land men on the Moon and return them safely to Earth had been accomplished. The Saturn V vehicle was developed by the Marshall Space Flight Center (MSFC) under the direction of Dr. Wernher von Braun.

Ortho-para transition rate in mu-molecular hydrogen and the proton's induced pseudoscalar coupling gp.

PubMed

Clark, J H D; Armstrong, D S; Gorringe, T P; Hasinoff, M D; King, P M; Stocki, T J; Tripathi, S; Wright, D H; Zolnierczuk, P A

2006-02-24

We report a measurement of the ortho-para transition rate in the p mu p molecule. The experiment was conducted at TRIUMF via the measurement of the time dependence of the 5.2 MeV neutrons from muon capture in liquid hydrogen. The measurement yielded an ortho-para rate Lambda op = (11.1 +/- 1.7 +/-(0.9)(0.6)) x 10(4) s(-1), which is substantially larger than the earlier result of Bardin et al. The result has striking implications for the proton's induced pseudoscalar coupling g(p), changing the value of g(p) obtained from the most precise ordinary muon capture measurement from 10.6 +/- 2.7 to 0.8 +/- 2.8, and from the sole radiative muon capture measurement from 12.2 +/- 1.1 to 10.6 +/- 1.2, bringing the latter result closer to theoretical predictions.

Piezo-tunnel effect in Al/Al2O3/Al junctions elaborated by atomic layer deposition

NASA Astrophysics Data System (ADS)

Rafael, R.; Puyoo, E.; Malhaire, C.

2017-11-01

In this work, the electrical transport in Al/Al2O3/Al junctions under mechanical stress is investigated in the perspective to use them as strain sensors. The metal/insulator/metal junctions are elaborated with a low temperature process (≤200 °C) fully compatible with CMOS back-end-of-line. The conduction mechanism in the structure is found to be Fowler-Nordheim tunneling, and efforts are made to extract the relevant physical parameters. Gauge factors up to -32.5 were found in the fabricated devices under tensile stress. Finally, theoretical mechanical considerations give strong evidence that strain sensitivity in Al/Al2O3/Al structures originates not only from geometrical deformations but also from the variation of interface barrier height and/or effective electronic mass in the tunneling oxide layer.

Influence of AlN(0001) Surface Reconstructions on the Wettability of an Al/AlN System: A First-Principle Study.

PubMed

Cao, Junhua; Liu, Yang; Ning, Xiao-Shan

2018-05-11

A successful application of a hot dip coating process that coats aluminum (Al) on aluminum nitride (AlN) ceramics, revealed that Al had a perfect wettability to the ceramics under specific circumstances, which was different from previous reports. In order to elucidate the mechanism that controlled the supernormal wetting phenomenon during the dip coating, a first-principle calculation of an Al(111)/AlN(0001) interface, based on the density functional theory (DFT), was employed. The wettability of the Al melt on the AlN(0001) surface, as well as the effect that the surface reconstruction of AlN and the oxygen adsorption had on Al for the adhesion and the wettability of the Al/AlN system, were studied. The results revealed that a LCM (laterally contracted monolayer) reconstruction could improve the adhesion and wettability of the system. Oxygen adsorption on the free surface of Al decreased the contact angle, because the adsorption reduced of the surface tension of Al. A prefect wetting was obtained only after some of the oxygen atoms adsorbed on the free surface of Al. The supernormal wetting phenomenon came from the surface reconstruction of the AlN and the adsorption of oxygen atoms on the Al melt surface.

Anion photoelectron spectroscopy of deprotonated ortho-, meta-, and para-methylphenol

NASA Astrophysics Data System (ADS)

Nelson, Daniel J.; Gichuhi, Wilson K.; Miller, Elisa M.; Lehman, Julia H.; Lineberger, W. Carl

2017-02-01

The anion photoelectron spectra of ortho-, meta-, and para-methylphenoxide, as well as methyl deprotonated meta-methylphenol, were measured. Using the Slow Electron Velocity Map Imaging technique, the Electron Affinities (EAs) of the o-, m-, and p-methylphenoxyl radicals were measured as follows: 2.1991±0.0014, 2.2177±0.0014, and 2.1199±0.0014 eV, respectively. The EA of m-methylenephenol was also obtained, 1.024±0.008 eV. In all four cases, the dominant vibrational progressions observed are due to several ring distortion vibrational normal modes that were activated upon photodetachment, leading to vibrational progressions spaced by ˜500 cm-1. Using the methylphenol O-H bond dissociation energies reported by King et al. and revised by Karsili et al., a thermodynamic cycle was constructed and the acidities of the methylphenol isomers were determined as follows: Δa c i dH298K 0=348.39 ±0.25 , 348.82±0.25, 350.08±0.25, and 349.60±0.25 kcal/mol for cis-ortho-, trans-ortho-, m-, and p-methylphenol, respectively. The excitation energies for the ground doublet state to the lowest excited doublet state electronic transition in o-, m-, and p-methylphenoxyl were also measured as follows: 1.029±0.009, 0.962±0.002, and 1.029±0.009 eV, respectively. In the photoelectron spectra of the neutral excited states, C-O stretching modes were excited in addition to ring distortion modes. Electron autodetachment was observed in the cases of both m- and p-methylphenoxide, with the para isomer showing a lower photon energy onset for this phenomenon.

Spectroscopy of Al wire array stagnation on Z

NASA Astrophysics Data System (ADS)

Jones, B.; Jennings, C. A.; Hansen, S. B.; Bailey, J. E.; Rochau, G. A.; Coverdale, C. A.; Yu, E. P.; Ampleford, D. J.; Cuneo, M. E.; Maron, Y.; Fisher, V. I.; Bernshtam, V.; Starobinets, A.; Weingarten, L.; Pinhas, S.

2011-10-01

In this work, we present analysis of time-gated spectra of ~2 keV K-shell emissions from Al (5% Mg) wire arrays on Z to provide details of the plasma conditions and dynamics at the onset of stagnation. The plasma is modeled as concentric radial zones, and collisional-radiative modeling with self-consistent radiation transport is used to constrain the temperatures and densities in these regions. A hot ~2 keV plasma core bearing a few percent of the total mass forms at the foot of the x-ray pulse, with participating mass increasing toward peak x-ray power as material arrives on axis with ~50 cm/ μs implosion velocity. The atomic modeling accounts for K-shell line opacity and Doppler effects, and is compared to 3D MHD simulations. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. DOE National Nuclear Security Administration under contract DE-AC04-94AL85000.

Japanese version of the ALS-FTD-Questionnaire (ALS-FTD-Q-J).

PubMed

Watanabe, Yasuhiro; Beeldman, Emma; Raaphorst, Joost; Izumi, Yuishin; Yoshino, Hiide; Masuda, Michihito; Atsuta, Naoki; Ito, Satoru; Adachi, Tadashi; Adachi, Yoshiki; Yokota, Osamu; Oda, Masaya; Hanashima, Ritsuko; Ogino, Mieko; Ichikawa, Hiroo; Hasegawa, Kazuko; Kimura, Hideki; Shimizu, Toshio; Aiba, Ikuko; Yabe, Hayato; Kanba, Makoto; Kusumi, Kimiyoshi; Aoki, Tetsuya; Hiroe, Yu; Watanabe, Hirohisa; Nishiyama, Kazutoshi; Nomoto, Masahiro; Sobue, Gen; Nakashima, Kenji

2016-08-15

Amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD) share common clinical, genetic and neuropathological features. Some ALS patients have behavioral/personality changes, which could result in significant obstacles in the care provided by family members and caregivers. An easy screening tool would contribute greatly to the evaluation of these symptoms. We translated the ALS-FTD-Questionnaire, developed in the Netherlands, into Japanese (ALS-FTD-Q-J) and examined the clinimetric properties (internal consistency, construct and clinical validity). Patients with ALS and/or behavioral variant FTD (bvFTD) were evaluated alongside healthy controls in this multicenter study. All ALS patients, regardless of bvFTD status, were further evaluated by the frontal behavioral inventory (FBI) and for frontal/executive function, cognition, anxiety/depression, and motor functions. Data from 146 subjects were analyzed: ALS (92), ALS-bvFTD (6), bvFTD (16), and healthy controls (32). The internal consistency of the ALS-FTD-Q-J was good (Cronbach α=0.92). The ALS-FTD-Q-J showed construct validity as it exhibited a high correlation with the FBI (r=0.79). However, correlations were moderate with anxiety/depression and low with cognitive scales, in contrast to the original report, i.e. a moderate correlation with cognition and a low correlation with anxiety/depression. The ALS-FTD-Q-J discriminated ALS patients from (ALS-)bvFTD patients and controls. Thus, the ALS-FTD-Q-J is useful for evaluating Japanese ALS/FTD patients. Copyright © 2016 Elsevier B.V. All rights reserved.

3-Dimensional Microstructure of Al-Al3Ti Alloy Severely Deformed by ECAP

NASA Astrophysics Data System (ADS)

Sato, Hisashi; Hishikawa, Takahisa; Makino, Yuuki; Kunimine, Takahiro; Watanabe, Yoshimi

Microstructure of Al-Al3Ti alloy deformed by Equal-Channel-Angular Pressing (ECAP) is 3-dimensionally investigated. Especially, distribution of Al3Ti particles is focused in this study. The Al-Al3Ti alloy has coarse Al3Ti platelet particles in α-Al matrix. When the Al-Al3Ti alloy is deformed by ECAP under route A, fine Al3Ti platelet particles are observed. These Al3Ti platelet particles are aligned along to deformation axis, and its plane normal is perpendicular to the deformation axis. On the other hand, Al-Al3Ti alloy ECAPed under route Bc forms several groups consisted of fine Al3Ti platelet particles. Moreover, longitudinal size of the Al3Ti particle groups is close to that of initial Al3Ti particles with 4-pass ECAP specimen. These distribution behaviors of the Al3Ti particle can be explained by plastic flow of α-Al matrix. Finally, it is concluded that distribution of Al3Ti particle in Al-Al3Ti alloy by ECAP is controlled by plastic deformation of α-Al matrix.

The architecture of the spliceosomal U4/U6.U5 tri-snRNP

PubMed Central

Nguyen, Thi Hoang Duong; Galej, Wojciech P.; Bai, Xiao-chen; Savva, Christos G.; Newman, Andrew J.; Scheres, Sjors H. W.; Nagai, Kiyoshi

2015-01-01

U4/U6.U5 tri-snRNP is a 1.5 MDa pre-assembled spliceosomal complex comprising U5 snRNA, extensively base-paired U4/U6 snRNAs and >30 proteins, including the key components Prp8, Brr2 and Snu114. The tri-snRNP combines with a pre-mRNA substrate bound to U1 and U2 snRNPs and transforms into a catalytically active spliceosome following extensive compositional and conformational changes triggered by unwinding of the U4/U6 snRNAs. CryoEM single-particle reconstruction of yeast tri-snRNP at 5.9Å resolution reveals the essentially complete organization of its RNA and protein components. The single-stranded region of U4 snRNA between its 3′-stem-loop and the U4/U6 snRNA stem I is loaded into the Brr2 helicase active site ready for unwinding. Snu114 and the N-terminal domain of Prp8 position U5 snRNA to insert its Loop I, which aligns the exons for splicing, into the Prp8 active site cavity. The structure provides crucial insights into the activation process and the active site of the spliceosome. PMID:26106855

Abu al-Layth al-Libi

DTIC Science & Technology

2015-02-01

in the region and apparently “showed brilliance in this regard through his perfect memorization , clever understanding, persistence, and patience...Taliban’s officials quietly left the capital without informing 73 Vernie Liebl, “Al-Qaida on the US Invasion of Afghanistan in Their Own Words ,” Small Wars... memorization . A talented and charismatic orator, he also used to deliver eulogies and `Id sermons. As to `Abdallah Sa`id al-Libi, his profile is similar

Defect structures in ordered intermetallics; grain boundaries and surfaces in FeAl, NiAl, CoAl and TiAl

NASA Astrophysics Data System (ADS)

Mutasa, Batsirai Manyara

Ordered intermetallics based on transition metal aluminides have been proposed as structural materials for advanced aerospace applications. The development of these materials, which have the advantages of low density and high operating temperatures, have been focused on the aluminides of titanium, nickel and iron. Though these materials exhibit attractive properties at elevated temperatures, their utilization is limited due to their propensity for low temperature fracture and susceptibility to decreased ductility due to environmental effects. A major embrittlement mechanism at ambient temperatures in these aluminides has been by the loss of cohesive strength at the interfaces (intergranular failure). This study focuses on this mechanism of failure, by undertaking a systematic study of the energies and structures of specific grain boundaries in some of these compounds. The relaxed atomistic grain boundary structures in B2 aluminides, FeAl, NiAl and CoAl and L10 gamma-TiAl were investigated using molecular statics and embedded atom potentials in order to explore general trends for a series of B2 compounds as well as TiAl. The potentials used correctly predict the proper mechanism of compositional disorder of these compounds. Using these potentials, point defects, free surface energies and various grain boundary structures of similar energies in three B2 compounds, FeAl, NiAl and CoAl were studied. These B2 alloys exhibited increasing anti-phase boundary energies respectively. The misorientations chosen for detailed study correspond to the Sigma5(310) and Sigma5(210) boundaries. These boundaries were investigated with consideration given to possible variations in the local chemical composition. The effects of both boundary stoichiometry and bulk stoichiometry on grain boundary energetics were also considered. Defect energies were calculated for boundaries contained in both stoichiometric and off-stoichiometric bulk. The surface energies for these aluminides were also

A Rechargeable Al/S Battery with an Ionic-Liquid Electrolyte.

PubMed

Gao, Tao; Li, Xiaogang; Wang, Xiwen; Hu, Junkai; Han, Fudong; Fan, Xiulin; Suo, Liumin; Pearse, Alex J; Lee, Sang Bok; Rubloff, Gary W; Gaskell, Karen J; Noked, Malachi; Wang, Chunsheng

2016-08-16

Aluminum metal is a promising anode material for next generation rechargeable batteries owing to its abundance, potentially dendrite-free deposition, and high capacity. The rechargeable aluminum/sulfur (Al/S) battery is of great interest owing to its high energy density (1340 Wh kg(-1) ) and low cost. However, Al/S chemistry suffers poor reversibility owing to the difficulty of oxidizing AlSx . Herein, we demonstrate the first reversible Al/S battery in ionic-liquid electrolyte with an activated carbon cloth/sulfur composite cathode. Electrochemical, spectroscopic, and microscopic results suggest that sulfur undergoes a solid-state conversion reaction in the electrolyte. Kinetics analysis identifies that the slow solid-state sulfur conversion reaction causes large voltage hysteresis and limits the energy efficiency of the system. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High-precision ID-TIMS zircon U-Pb geochronology using new 1013 Ohm resistors

NASA Astrophysics Data System (ADS)

Von Quadt, A.; Buret, Y.; Large, S.; Peytcheva, I.; Trinquier, A.; Wotzlaw, J. F.

2015-12-01

Faraday cups equipped with high gain amplifiers provide a means to measure small ion beams in static mode without the limited linear range of ion counting systems. We tested the application of newly available 1013 Ohm resistors to ID-TIMS zircon U-Pb geochronology using a range of natural and synthetic reference materials. The TritonPlus-RPQ at the Institute of Geochemistry and Petrology, ETH Zurich, is equipped with five new 1013 Ohm resistors and one MasCom secondary electron multiplier, allowing to measure the 202-204-205-206-207-208Pb masses in static mode. U is measured subsequently as U-oxide (265-267-270UO2) during a second step, also in static Faraday mode. The gain calibration of the 1013 Ohm resistors was performed using the procedure of Trinquier (2014), with 144Nd-146Nd being measured using 1011 Ohm resistor and 142-143-145-148-150Nd being measured using 1013 Ohm resitors (Trinquier, 2014; Koornneef et al., 2014). Standard deviations of the noise in all five new 1013 Ohm resistors are lower than 5.0 x 10-6 over a 6 month period, with no shift occurring over this time interval. This new detector set-up was tested by analyzing natural zircon standard materials and synthetic U/Pb solutions (www.earthime.org), ranging in age from ~2 Ma to ~600 Ma. All natural zircon standards were chemically abraded (Mattinson, 2005) and all samples were spiked with the ET2535 tracer solution. U-Pb dates obtained using the static measurement routine are compared to measurements employing dynamic peak jumping routines on the MasCom multiplier. This study illustrates the benefits and current limitations of using high gain amplifiers to measure small ion beams for zircon U-Pb geochronology compared to conventional dynamic ion counting techniques. Mattinson, J.M. (2005) Chemical Geology 220:47-66; Trinquier, A. (2014) Application Note 30281; Koornneef, J. et al (2014) Analytica Chimica Acta 819:49-55.

78 FR 11164 - Intent To Grant an Exclusive License of U.S. Government-Owned Invention

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-15

... Specificities to Protein and Lipid Epitopes,'' to Avanti Polar Lipids with its principal place of business at 700 Industrial Park Drive, Alabaster, AL 35007. ADDRESSES: Commander, U.S. Army Medical Research and... FURTHER INFORMATION CONTACT: For licensing issues, Dr. Paul Mele, Office of Research & Technology...

Feldspar palaeo-isochrons from early Archaean TTGs: Pb-isotope evidence for a high U/Pb terrestrial Hadean crust

NASA Astrophysics Data System (ADS)

Kamber, B. S.; Whitehouse, M. J.; Moorbath, S.; Collerson, K. D.

2001-12-01

Feldspar lead-isotope data for 22 early Archaean (3.80-3.82 Ga) tonalitic gneisses from an area south of the Isua greenstone belt (IGB),West Greenland, define a steep linear trend in common Pb-isotope space with an apparent age of 4480+/-77 Ma. Feldspars from interleaved amphibolites yield a similar array corresponding to a date of 4455+/-540 Ma. These regression lines are palaeo-isochrons that formed during feldspar-whole rock Pb-isotope homogenisation a long time (1.8 Ga) after rock formation but confirm the extreme antiquity (3.81 Ga) of the gneissic protoliths [1; this study]. Unlike their whole-rock counterparts, feldspar palaeo-isochrons are immune to rotational effects caused by the vagaries of U/Pb fractionation. Hence, comparison of their intercept with mantle Pb-isotope evolution models yields meaningful information regarding the source history of the magmatic precursors. The locus of intersection between the palaeo-isochrons and terrestrial mantle Pb-isotope evolution lines shows that the gneissic precursors of these 3.81 Ga gneisses were derived from a source with a substantially higher time-integrated U/Pb ratio than the mantle. Similar requirements for a high U/Pb source have been found for IGB BIF [2], IGB carbonate [3], and particularly IGB galenas [4]. Significantly, a single high U/Pb source that separated from the MORB-source mantle at ca. 4.3 Ga with a 238U/204Pb of ca. 10.5 provides a good fit to all these observations. In contrast to many previous models based on Nd and Hf-isotope evidence we propose that this reservoir was not a mantle source but the Hadean basaltic crust which, in the absence of an operating subduction process, encased the early Earth. Differentiation of the early high U/Pb basaltic crust could have occurred in response to gravitational sinking of cold mantle material or meteorite impact, and produced zircon-bearing magmatic rocks. The subchondritic Hf-isotope ratios of ca. 3.8 Ga zircons support this model [5] provided that

Iraq: U.S. Regime Change Efforts and Post-Saddam Governance

DTIC Science & Technology

2005-04-26

States; the group began integrating into the broader opposition front in September 2002. In post-Saddam Iraq, Kanna served on the IGC. 23 Deyoung...Democratic Movement, which is headed by Yonadam Yousif Kanna .22 The Administration also began training about 5,000 oppositionists to assist U.S. forces,23...president of Saudi-based Hicap Technology. ! Assyrian leader Yonadam Kanna ! Iraqi Communist Party head Hamid al-Musa, a Shiite Muslim. The party is

Growth of Ni-Al alloys on Ni(1 1 1), from Al deposits of various thicknesses: (II) Formation of NiAl over a Ni 3Al interfacial layer

NASA Astrophysics Data System (ADS)

Le Pévédic, S.; Schmaus, D.; Cohen, C.

2007-01-01

This paper describes the second part of a study devoted to the growth of thin Ni-Al alloys after deposition of Al on Ni(1 1 1). In the previous paper [S. Le Pévédic, D. Schmaus, C. Cohen, Surf. Sci. 600 (2006) 565] we have described the results obtained for ultra-thin Al deposits, leading, after annealing at 750 K, to an epitaxial layer of Ni 3Al(1 1 1). In the present paper we show that this regime is only observed for Al deposits smaller than 8 × 10 15 Al/cm 2 and we describe the results obtained for Al deposits exceeding this critical thickness, up to 200 × 10 15 Al/cm 2. Al deposition was performed at low temperature (around 130 K) and the alloying process was followed in situ during subsequent annealing, by Auger electron spectroscopy, low energy electron diffraction and ion beam analysis-channeling measurements, in an ultra-high vacuum chamber connected to a Van de Graaff accelerator. We evidence the formation, after annealing at 750 K, of a crystallographically and chemically well-ordered NiAl(1 1 0) layer (whose thickness depends on the deposited Al amount), over a Ni 3Al "interfacial" layer (whose thickness—about 18 (1 1 1) planes—is independent of the deposited Al amount). The NiAl overlayer is composed of three variants, at 120° from each other in the surface plane, in relation with the respective symmetries of NiAl(1 1 0) and Ni 3Al(1 1 1). The NiAl layer is relaxed (the lattice parameters of cc-B2 NiAl and fcc-L1 2 Ni 3Al differ markedly), and we have determined its epitaxial relationship. In the case of the thickest alloyed layer formed the results concerning the structure of the NiAl layer have been confirmed and refined by ex situ X-ray diffraction and information on its grain size has been obtained by ex situ Atomic Force Microscopy. The kinetics of the alloying process is complex. It corresponds to an heterogeneous growth leading, above the thin Ni 3Al interfacial layer, to a mixture of Al and NiAl over the whole Al film, up to the

Multidisciplinary ALS care improves quality of life in patients with ALS.

PubMed

Van den Berg, J P; Kalmijn, S; Lindeman, E; Veldink, J H; de Visser, M; Van der Graaff, M M; Wokke, J H J; Van den Berg, L H

2005-10-25

To examine the effect of multidisciplinary ALS care on the quality-of-life (QoL) in patients with ALS and their caregivers. In a cross-sectional study, 208 patients with ALS and their caregivers were interviewed. QoL was assessed using the 36-item Short Form Health Survey (SF-36) and two visual analogue scales (VAS). Criteria for multidisciplinary ALS care were: an ALS team headed by a consultant in rehabilitation medicine and consisting of at least a physical therapist, occupational therapist, speech pathologist, dietician and a social worker; use of the Dutch ALS consensus guidelines for ALS care; and at least six incident ALS patients per year. Clinical characteristics and functional loss of the 133 patients receiving multidisciplinary ALS care and the 75 patients receiving general ALS care were similar. The percentage of patients with adequate aids and appliances was higher in those with multidisciplinary ALS care (93.1 vs 81.3%, p = 0.008), whereas the number of visits to professional caregivers was similar in both groups. Patients in the multidisciplinary ALS care group had a better mental QoL on the SF-36 Mental Summary Score than those in the general care group (p = 0.01). The difference in QoL was most pronounced in the domains of Social Functioning and Mental Health, and was independent of the presence of aids and appliances. No significant differences were found in the SF-36 Physical Summary Score, VAS, or in QoL of caregivers of patients with ALS. High standard of care improves mental quality-of-life in patients with ALS.

TEM Characterization of High Burn-up Microstructure of U-7Mo Alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jian Gan; Brandon Miller; Dennis Keiser

2014-04-01

As an essential part of global nuclear non-proliferation effort, the RERTR program is developing low enriched U-Mo fuels (< 20% U-235) for use in research and test reactors that currently employ highly enriched uranium fuels. One type of fuel being developed is a dispersion fuel plate comprised of U-7Mo particles dispersed in Al alloy matrix. Recent TEM characterizations of the ATR irradiated U-7Mo dispersion fuel plates include the samples with a local fission densities of 4.5, 5.2, 5.6 and 6.3 E+21 fissions/cm3 and irradiation temperatures of 101-136?C. The development of the irradiated microstructure of the U-7Mo fuel particles consists ofmore » fission gas bubble superlattice, large gas bubbles, solid fission product precipitates and their association to the large gas bubbles, grain subdivision to tens or hundreds of nanometer size, collapse of bubble superlattice, and amorphisation. This presentation will describe the observed microstructures specifically focusing on the U-7Mo fuel particles. The impact of the observed microstructure on the fuel performance and the comparison of the relevant features with that of the high burn-up UO2 fuels will be discussed.« less

Probing disk wind and other properties of 4U 1630-47

NASA Astrophysics Data System (ADS)

Bhattacharyya, Sudip

2015-09-01

The accreting Galactic black hole transient 4U 1630-47, which is currently in outburst, is an ideal source to probe two types of accreted matter ejection: (1) via disk wind and (2) via jet, both using the observed narrow spectral lines (Diaz Trigo et al., 2013, Nature, 504, 206; Neilsen et al. 2014; Diaz Trigo et al. 2014). Chandra gratings are ideal to study such lines. The source also showed indications of high-frequency (HF) quasi-periodic oscillations (QPOs) in a rather high (150-450 Hz) frequency range, which can be extremely useful to probe the strong gravity regime. The AstroSat satellite, because of its large area and high timing resolution in a broad energy band, can potentially detect and measure HF QPOs and probe the source broadband spectrum and state. Hence, our proposed 30 ks Chandra exposure, nearly contemporaneous with complementary AstroSat observations, will provide an excellent way to probe the accretion and ejection mechanism in the strong gravity regime.

Finding the "true" age: ways to read high-precision U-Pb zircon dates

NASA Astrophysics Data System (ADS)

Schaltegger, U.; Schoene, B.; Ovtcharova, M.; Sell, B. K.; Broderick, C. A.; Wotzlaw, J.

2011-12-01

rheological lockup by the crystals. Last crystallizing zircons in the interstitial melt may therefore postdate emplacement of the magma. The range of 206Pb/238U ages may yield a time frame for the cooling of a given magma batch, which could be added to quantitative thermal models of magma emplacement and cooling. Hf isotopes and trace elements of the dated zircon are used to trace the nature of the dated grains [4], specifically for identification of crystals that form earlier at lower crustal levels (antecrysts). Autocrystic zircons typically show, e.g., distinctly different (higher or lower) Th/U ratios. Cautiously interpreted high-precision U-Pb data of chemically abraded zircons may resolve the evolution of a magmatic system from its roots to final emplacement or eruption, trace fractional crystallization of zircon and other accessory and major phases in a magma batch, and add quantitative temporal constraints to thermal models. The proposed interpretation scheme thus adds significant information compared to conventional statistics. [1] Mattinson J., 2005, Chem. Geol. 200, 47-66; ; [2] Slama et al., 2008, Chem. Geol. 249, 1-35; [3] Miller et al., 2007, J. Volc. Geotherm. Res. 167, 282-299; [4] Schoene et al., 2010, Geochim. Cosmochim. Acta 74, 7144-7159

The half-metallicity of LiMgPdSn-type quaternary Heusler alloys FeMnScZ (Z=Al, Ga, In): A first-principle study

NASA Astrophysics Data System (ADS)

Gao, Y. C.; Gao, X.

2015-05-01

Based on the first-principles calculations, quaternary Heusler alloys FeMnScZ (Z=Al, Ga, In) including its phase stability, band gap, the electronic structures and magnetic properties has been studied systematically. We have found that, in terms of the equilibrium lattice constants, FeMnScZ (Z=Al, Ga, In) are half-metallic ferrimagnets, which can sustain the high spin polarization under a very large amount of lattice distortions. The half-metallic band gap in FeMnScZ (Z=Al, Ga, In) alloys originates from the t1u-t2g splitting instead of the eu-t1u splitting. The total magnetic moments are 3μB per unit cell for FeMnScZ (Z=Al, Ga, In) alloys following the Slater-Pauling rule with the total number of valence electrons minus 18 rather than 24. According to the study, the conclusion can be drawn that all of these compounds which have a negative formation energy are possible to be synthesized experimentally.

U2AF1 mutations alter splice site recognition in hematological malignancies.

PubMed

Ilagan, Janine O; Ramakrishnan, Aravind; Hayes, Brian; Murphy, Michele E; Zebari, Ahmad S; Bradley, Philip; Bradley, Robert K

2015-01-01

Whole-exome sequencing studies have identified common mutations affecting genes encoding components of the RNA splicing machinery in hematological malignancies. Here, we sought to determine how mutations affecting the 3' splice site recognition factor U2AF1 alter its normal role in RNA splicing. We find that U2AF1 mutations influence the similarity of splicing programs in leukemias, but do not give rise to widespread splicing failure. U2AF1 mutations cause differential splicing of hundreds of genes, affecting biological pathways such as DNA methylation (DNMT3B), X chromosome inactivation (H2AFY), the DNA damage response (ATR, FANCA), and apoptosis (CASP8). We show that U2AF1 mutations alter the preferred 3' splice site motif in patients, in cell culture, and in vitro. Mutations affecting the first and second zinc fingers give rise to different alterations in splice site preference and largely distinct downstream splicing programs. These allele-specific effects are consistent with a computationally predicted model of U2AF1 in complex with RNA. Our findings suggest that U2AF1 mutations contribute to pathogenesis by causing quantitative changes in splicing that affect diverse cellular pathways, and give insight into the normal function of U2AF1's zinc finger domains. © 2015 Ilagan et al.; Published by Cold Spring Harbor Laboratory Press.

AlGaN-based ultraviolet light-emitting diodes on sputter-deposited AlN templates with epitaxial AlN/AlGaN superlattices

NASA Astrophysics Data System (ADS)

Zhao, Lu; Zhang, Shuo; Zhang, Yun; Yan, Jianchang; Zhang, Lian; Ai, Yujie; Guo, Yanan; Ni, Ruxue; Wang, Junxi; Li, Jinmin

2018-01-01

We demonstrate AlGaN-based ultraviolet light-emitting diodes (UV-LEDs) grown by metalorganic chemical vapor deposition (MOCVD) on sputter-deposited AlN templates upon sapphire substrates. An AlN/AlGaN superlattices structure is inserted as a dislocation filter between the LED structure and the AlN template. The full width at half maximum values for (0002) and (10 1 bar 2) X-ray rocking curves of the n-type Al0.56Ga0.44N layer are 513 and 1205 arcsec, respectively, with the surface roughness of 0.52 nm. The electron concentration and mobility measured by Hall measurement are 9.3 × 1017cm-3 and 54 cm2/V·s at room temperature, respectively. The light output power of a 282-nm LED reaches 0.28 mW at 20 mA with an external quantum efficiency of 0.32%. And the values of leakage current and forward voltage of the LEDs are ∼3 nA at -10 V and 6.9 V at 20 mA, respectively, showing good electrical performance. It is expected that the cost of the UV-LED can be reduced by using sputter-deposited AlN template.

U.S. Korean Youth's Ideas and Experience of U.S. Education, U.S. Society, and U.S. History

ERIC Educational Resources Information Center

An, Sohyun

2009-01-01

Drawing on and conversing with the large body of research and literature on young people's historical understanding, Asian American education, transnational migration, and Korean American studies, this dissertation research explored contemporary U.S. Korean youth's ideas and experiences of U.S. education, U.S. society and U.S. history.…

Combined apatite fission track and U-Pb dating by LA-ICPMS

NASA Astrophysics Data System (ADS)

Chew, D. M.; Donelick, R. A.

2012-04-01

Apatite is a common accessory mineral in igneous, metamorphic and clastic sedimentary rocks. It is a nearly ubiquitous accessory phase in igneous rocks, is common in metamorphic rocks of pelitic, carbonate, basaltic, and ultramafic composition and is virtually ubiquitous in clastic sedimentary rocks. In contrast to the polycyclic behavior of the stable heavy mineral zircon, apatite is unstable in acidic groundwaters and has limited mechanical stability in sedimentary transport systems. Apatite has many potential applications in provenance studies, particularly as it likely represents first-cycle detritus. Fission track and U-Pb dating are very powerful techniques in apatite provenance studies. They yield complementary information, with the apatite fission-track system yielding low-temperature exhumation ages and the U-Pb system yielding high-temperature cooling ages which constrain the timing of apatite crystallization. This study focuses on integrating apatite fission track and U-Pb dating by the LA-ICPMS method. Our approach is intentionally broad in scope, and is applicable to any quadrupole or rapid-scanning magnetic-sector LA-ICPMS system. Calculating uranium concentrations in fission-track dating by LA-ICPMS increases the speed of analysis and sample throughput compared to the conventional external detector method and avoids the need for neutron irradiation (Hasebe et al., 2004). LA-ICPMS-based uranium measurements in apatite are measured relative to an internal concentration standard (typically 43Ca). Ca in apatite is not always stochiometric as minor cations (Mn2+, Sr2+, Ba2+ and Fe2+) and REE can substitute with Ca2+. These substitutions must be quantified by multi-elemental LA-ICPMS analyses. Such data are also useful for discriminating between different apatite populations in sedimentary or volcaniclastic rocks based on their trace-element chemistry. Low U, Th and radiogenic Pb concentrations, elevated common Pb / radiogenic Pb ratios and U-Pb elemental

Cyclic oxidation resistance of a reaction milled NiAl-AlN composite

NASA Technical Reports Server (NTRS)

Lowell, Carl E.; Barrett, Charles A.; Whittenberger, J. D.

1990-01-01

Based upon recent mechanical property tests a NiAl-AlN composite produced by cryomilling has very attractive high temperature strength. This paper focuses on the oxidation resistance of the NiAl-AlN composite at 1473 and 1573 K as compared to that of Ni-47Al-0.15Zr, one of the most oxidation resistant intermetallics. The results of cyclic oxidation tests show that the NiAl-AlN composite has excellent properties although not quite as good as those of Ni-47Al-0.15Zr. The onset of failure of the NiAl-AlN was unique in that it was not accompanied by a change in scale composition from alumina to less protective oxides. Failure in the composite appears to be related to the entrapment of AlN particles within the alumina scale.

ALS-Plus Syndrome: Non-Pyramidal Features in a Large ALS Cohort

PubMed Central

McCluskey, Leo; Vandriel, Shannon; Elman, Lauren; Van Deerlin, Vivianna M.; Powers, John; Boller, Ashley; Wood, Elisabeth McCarty; Woo, John; McMillan, Corey T.; Rascovsky, Katya; Grossman, Murray

2014-01-01

Objective Autopsy studies show widespread pathology in amyotrophic lateral sclerosis (ALS), but clinical surveys of multisystem disease in ALS are rare. We investigated ALS-Plus syndrome, an understudied group of patients with clinical features extending beyond pyramidal and neuromuscular systems with or without cognitive/behavioral deficits. Methods In a large, consecutively-ascertained cohort of 550 patients with ALS, we documented atypical clinical manifestations. Genetic screening for C9orf72 hexanucleotide expansions was performed in 343 patients, and SOD1, TARDBP, and VCP were tested in the subgroup of patients with a family history of ALS. Gray matter and white matter imaging was available in a subgroup of 30 patients. Results Seventy-five (13.6%) patients were identified with ALS-Plus syndrome. We found disorders of ocular motility, cerebellar, extrapyramidal and autonomic functioning. Relative to those without ALS-Plus, cognitive impairment (8.0% vs 2.9%, p=0.029), bulbar-onset (49.3% vs 23.2%, p<0.001), and pathogenic mutations (20.0% vs 8.4%, p=0.015) were more than twice as common in ALS-Plus. Survival was significantly shorter in ALS-Plus (29.66 months vs 42.50 months, p=0.02), regardless of bulbar-onset or mutation status. Imaging revealed significantly greater cerebellar and cerebral disease in ALS-Plus compared to those without ALS-Plus. Conclusions ALS-Plus syndrome is not uncommon, and the presence of these atypical features is consistent with neuropathological observations that ALS is a multisystem disorder. ALS-Plus syndrome is associated with increased risk for poor survival and the presence of a pathogenic mutation. PMID:25086858

Laser-Ablation (U-Th)/He Geochronology

NASA Astrophysics Data System (ADS)

Hodges, K.; Boyce, J.

2003-12-01

ablation experiments results in considerably worse spatial resolution than that typically possible for 40Ar/39Ar laser microprobe dating, it is possible to site the LA-ICPMS ablation pit within a few microns of the pit used for He extraction, or to simply re-occupy and enlarge the original ablation pit. The potential effective spatial resolution of the technique is thus on the order of a few tens to roughly 100 microns. As a proof-of-concept exercise, we have applied this technique to fluorapatite from Cerro de Mercado, Durango, Mexico, which has a generally accepted (U-Th)/He age of 32.1 +/- 3.4 Ma (2 sigma) based on single-crystal fusion analyses reported by House et al. (2000, EPSL). Using the approach described above, we made 48 separate age measurements on a 12 mm polished section cut through a single crystal of Durango fluorapatite perpendicular to its c axis. The measured dates yield a mean of 34.9 +/- 5.1 Ma (2 sigma), with a total dispersion of dates comparable to that reported by House et al. Much of the apparent age variation observed in both studies is due to documented U+Th heterogeneities in single crystals of the Durango fluorapatite. Nevertheless, the consistency of the laser ablation and conventional results for this material is striking. Compared to conventional laser and furnace methods of (U-Th)/He geochronology, the laser microprobe approach offers substantially improved spatial resolution, and the ability to avoid (or at least minimize) alpha-ejection corrections. In addition, the method affords improved sample throughput, such that age estimates for homogeneous materials can be made with considerably higher precision based on a larger number of analyses.

Irradiation performance of U-Mo monolithic fuel

DOE PAGES

Meyer, M. K.; Gan, J.; Jue, J. F.; ...

2014-04-01

High-performance research reactors require fuel that operates at high specific power to high fission density, but at relatively low temperatures. Research reactor fuels are designed for efficient heat rejection, and are composed of assemblies of thin-plates clad in aluminum alloy. The development of low-enriched fuels to replace high-enriched fuels for these reactors requires a substantially increased uranium density in the fuel to offset the decrease in enrichment. Very few fuel phases have been identified that have the required combination of very-high uranium density and stable fuel behavior at high burnup. U-Mo alloys represent the best known tradeoff in these properties.more » Testing of aluminum matrix U-Mo aluminum matrix dispersion fuel revealed a pattern of breakaway swelling behavior at intermediate burnup, related to the formation of a molybdenum stabilized high aluminum intermetallic phase that forms during irradiation. In the case of monolithic fuel, this issue was addressed by eliminating, as much as possible, the interfacial area between U-Mo and aluminum. Based on scoping irradiation test data, a fuel plate system composed of solid U-10Mo fuel meat, a zirconium diffusion barrier, and Al6061 cladding was selected for development. Developmental testing of this fuel system indicates that it meets core criteria for fuel qualification, including stable and predictable swelling behavior, mechanical integrity to high burnup, and geometric stability. In addition, the fuel exhibits robust behavior during power-cooling mismatch events under irradiation at high power.« less

Valence subband coupling effect on polarization of spontaneous emissions from Al-rich AlGaN/AlN quantum wells.

PubMed

Lu, Huimin; Yu, Tongjun; Yuan, Gangcheng; Jia, Chuanyu; Chen, Genxiang; Zhang, Guoyi

2012-12-03

The optical polarization properties of Al-rich AlGaN/AlN quantum wells (QWs) were investigated using the theoretical model based on the k·p method. Numerical results show that there is valence subband coupling which can influence the peak emission wavelength and emission intensity for TE and TM polarization components from Al-rich AlGaN/AlN QWs. Especially the valence subband coupling could be strong enough when CH1 is close to HH1 and LH1 subbands to modulate the critical Al content switching dominant emissions from TE to TM polarization. It is believed that the valence subband coupling may give important influence on polarization properties of spontaneous emissions and should be considered in designing high efficiency AlGaN-based ultraviolet (UV) LEDs.

Modulating optical polarization properties of Al-rich AlGaN/AlN quantum well by controlling wavefunction overlap

NASA Astrophysics Data System (ADS)

Chen, X. J.; Yu, T. J.; Lu, H. M.; Yuan, G. C.; Shen, B.; Zhang, G. Y.

2013-10-01

Using modified k.p perturbation method, the optical polarization properties of Al-rich AlGaN/AlN quantum wells (QWs) are studied. It is found that change of wavefunction overlaps between conduction band and valance subbands of heavy hole, light hole, and crystal-field split off hole is different. Such difference leads to the overturn of polarization degree and modulates optical polarization properties as well width and strain vary. This prompts that changing wavefunction overlaps of electron and hole can lead to a way to modulate optical polarization properties of Al-rich AlGaN/AlN QWs, on no condition that valence band order changes.

Effect of AlB2 on the P-threshold in Al-Si alloy

NASA Astrophysics Data System (ADS)

Wu, Yuying; Liu, Xiangfa

2018-06-01

The nucleation of primary Si in Al-Si alloys has been investigated in this work. It was found that there was a threshold concentration of P, below which AlP can not heterogeneous nucleate primary Si in Al-12 wt%Si alloy. AlB2 can not nucleate primary Si directly, but the presence of AlB2 may assist the nucleation of AlP leading to the nucleation of primary Si particles. In addition, with addition of AlB2, the nucleation efficiency of AlP can be improved in Al-18 wt%Si alloy. The orientation relationship between AlB2 and AlP has been calculated, and the adsorption model for AlB2 and AlP was proposed in this work.

Unfocused Energy: A Strategic Approach to U.S. Communications in Afghanistan

DTIC Science & Technology

2010-05-21

of public relations through mass manipulation. Bernays professionally espoused the notion that in a democracy, the 14 Allan M . Winkler, The Politics...2009. 37 BIBLIOGRAPHY Al-Imarat, M . The Information Revolution and the Arab world: Its Impact on State and Society. Abu Dhabi, UAE, 1998...Dizard, W. P., The Strategy of Truth: The Story of the U.S. Information Agency, Washington D.C: Public Affairs Press, 1961. Donini , Antonio, Norah

Electron correlation and relativity of the 5f electrons in the U-Zr alloy system

NASA Astrophysics Data System (ADS)

Söderlind, P.; Sadigh, B.; Lordi, V.; Landa, A.; Turchi, P. E. A.

2014-01-01

We address a recently communicated conception that spin-orbit interaction and strong electron correlations are important for the metal fuel U-Zr system. Here, we show that (i) relativistic effects only marginally correct the uranium metal equation-of-state and (ii) addition of onsite Coulomb repulsion leads to an unphysical magnetic ground state of the body-centered cubic (γ) phase and a grossly overestimated equilibrium volume. Consequently, LSDA + U is deemed unsuitable for describing the electronic structure of the U-Zr system. Recently, Xiong et al. [1] reported on thermodynamic modeling of the U-Zr system motivated by its potential as a nuclear fuel for fast breeder reactors. This work [1] came on the heels of another report by Landa et al. [2] on the same system, but with very different results for the formation enthalpies and ultimate conclusion on the U-Zr phase diagram. The authors [1] argue that their calculated energetics are significantly more accurate than that by Landa et al. [2], and they further attribute the difference to strong electron correlations and the relativistic spin-orbit interaction.In the present letter we show that uranium metal, and thus the U-Zr metal nuclear fuel system, possess weakly correlated electrons that are adequately described within density-functional theory in the generalized gradient approximation, and that addition of onsite Coulomb repulsion using the LSDA + U formalism leads to finite magnetization of the γ phase in contradiction to experiments. Furthermore, we show that spin-orbit interaction is quite weak in uranium metal and that its inclusion will not significantly change the chemical bonding and formation enthalpies.In order to illustrate our arguments, we perform comparative electronic-structure calculations using the full-potential linear augmented plane-wave (FPLAPW) method and the projector augmented plane-wave (PAW) method as implemented in the Wien2K [3

Zircon U-Pb Geochronology, Hf Isotopic Composition and Geological Implications of the Neoproterozoic Huashan Group in the Jingshan Area, Northern Yangtze Block, China

NASA Astrophysics Data System (ADS)

Yang, Z.; Yang, K.

2015-12-01

In the northern Yangtze Block, a clear angular unconformity between the Mesoproterozoic sequences (e.g. Dagushi Group) and the overlying Neoproterozoic strata (e.g. Huashan Group) marks the the Jinning orogeny. A combined study of Lu-Hf isotopes and U-Pb ages for detrital zircons from Huashan Group can provide information on the crustal evolution of sedimentary provenances and the timing of the Jinning orogeny. Detrital zircons from Huashan Group have two major U-Pb age populations of about 2.0Ga, 2.65Ga, and three subordinate age groups of about 0.82Ga, 2.5Ga, 2.9Ga with minor >3.0Ga ages. The youngest five analyses yield a weighted average age of 816±9Ma, which is consistent with that of interlayered basalt (824±9Ma, Deng et al., 2013) and roughly defines the minimum depositional age of Huashan Group. Detrital zircons of Huashan Group mostly have two stage Hf isotope model ages (TDM2) between 3.0 to 3.3Ga, indicating that the northern Yangtze Block experienced significant continental crustal growth during the Paleo- to Meso-archean. Similar U-Pb ages of detrital zircons have been obtained from Precambrian sedimentary rocks in the northern Yangtze Block from previous studies (Liu et al., 2008; Guo et al., 2014 and references therein). Recently, ca. 2.65Ga A-type granites had been reported from the Kongling and Huji area, which likely record the thermally stable lithosphere (Chen et al., 2013; Zhou et al., 2015). In combination with this study, it documents the widespread 2.6-2.7Ga magmatic rocks in the northern Yangtze Block. Zhao et al. (2013) demonstrated both the ca. 850Ma tonalite and trondhjemite of the Huangling igneous complex were formed in a continental arc setting. This suggests the Miaowan-Huashan oceanic basin proposed by Bader et al. (2013) has not been closed at ca. 850Ma. This evidence, together with the depositional age of the Huashan Group, indicates the Jinning orogeny took place at 850-820 Ma. [1] Bader et al., 2013 Tectonics [2] Deng et al

County-level Estimates for Carbon Distribution in U.S. Croplands, 1990-2005

DOE Data Explorer

West, Tristram O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2008-01-01

Net Primary Productivity (NPP) for croplands can be estimated using a statistical method that includes factors for dry weight, harvest indices, and root:shoot ratios multiplied by yield data from the National Agricultural Statistics Service (NASS). This method has been documented and published by Prince et al. (2001), Hicke and Lobell (2004), and Hicke et al. (2004). We expanded this method by including factors for more crops and by using an estimated carbon content of 0.45 for agricultural crops to estimate (a) total net carbon uptake, (b) carbon in aboveground biomass, (c) carbon in belowground biomass, (d) carbon harvested and transported off site, and (e) the amount of carbon remaining on the surface following harvest. These five variables are included with their respective Federal Information Processing Standards (FIPS) codes for all counties in the contiguous U.S. from 1990-2005. A mean harvest efficiency of 0.95 was assumed across all crops. Total cropland NPP for the U.S. ranges from 378-527 Tg C yr^-1 within years 1990-2005, and total carbon harvested and removed ranges from 161-228 Tg C yr^-1 within years 1990-2005.

High temperature deformation of NiAl and CoAl

NASA Technical Reports Server (NTRS)

Nix, W. D.

1982-01-01

The high temperature mechanical properties of the aluminides are reviewed with respect to their potential as high temperature structural materials. It is shown that NiAl and CoAl are substantially stronger than the pure metals Ni and Co at high temperatures and approach the strength of some superalloys, particularly when those superalloys are tested in "weak" directions. The factors that limit and control the high temperature strengths of NiAl and CoAl are examined to provide a basis for the development of intermetallic alloys of this type.

75 FR 5132 - United States v. Cameron International Corp., et al.; Proposed Final Judgment and Competitive...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-01

... DEPARTMENT OF JUSTICE Antitrust Division United States v. Cameron International Corp., et al.; Proposed Final Judgment and Competitive Impact Statement Notice is hereby given pursuant to the Antitrust Procedures and Penalties Act, 15 U.S.C. 16(b)-(h), that a proposed Final Judgment, Stipulation and Competitive Impact Statement have been filed...

76 FR 81528 - United States v. Exelon Corporation, et al.; Proposed Final Judgment and Competitive Impact...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-28

... DEPARTMENT OF JUSTICE Antitrust Division United States v. Exelon Corporation, et al.; Proposed Final Judgment and Competitive Impact Statement Notice is hereby given pursuant to the Antitrust Procedures and Penalties Act, 15 U.S.C. 16(b)-(h) that a proposed Final Judgment, Stipulation and Competitive Impact Statement have been filed with the...

Nuevos sistemas de frecuencia intermedia para el IAR

NASA Astrophysics Data System (ADS)

Olalde, J. C.; Perilli, D.; Larrarte, J. J.

Se presenta el diagrama en bloques de los nuevos sistemas de Frecuencia Intermedia para los dos radiómetros instalados en el IAR. Entre las características más importantes del sistema podemos mencionar la posibilidad de conectar cualquiera de las dos antenas a los ``backend" disponibles: analizador espectral de alta resolución (META II) de 0,05 Hz, autocorrelador de 1008 canales y contínuo. Se incorporan al sistema nuevos sintetizadores de frecuencia implementados con PLL y la moderna técnica de síntesis digital directa. Por último, el conjunto del sistema es susceptible de ser configurado por las computadoras de adquisición de datos, supervisadas por otra, que entrega el estado de funcionamiento actual y evita la selección de configuraciones incorrectas por parte del usuario.

Zircon U-Th and U-Pb Ages From Quaternary Silicic Volcanic and Plutonic Rocks, and Their Bearing on Granitoid Batholiths

NASA Astrophysics Data System (ADS)

Bacon, C. R.

2007-12-01

In the ten years since publication of M. Reid et al.'s seminal paper on zircon ages from rhyolites (EPSL 150:2-39, 1997) >20 papers have appeared on SIMS 238U-230Th and 238U-206Pb geochronology of zircon from silicic volcanic rocks, plutonic xenoliths, and young intrusions. In some cases, as well as for U-Pb studies of Tertiary granitoids, plutonic samples are interpreted in the context of related volcanism. These geochronologic data have advanced conceptual models of silicic magma genesis and pluton construction. Of fundamental importance are discoveries that zircons in volcanic rocks typically pre-date eruption by 10's to 100's of kyr and that multiple zircon populations are common; these crystals are "antecrysts" recycled from intrusive rocks or crystal mush of the system that vented. Resolving such age differences is possible with U-Th at <300 ka but is challenging with U-Pb, where SIMS precision limits resolution of differences on the order of 100 kyr for Pleistocene-Miocene zircons. Cathodoluminescence (CL) imaging of polished crystals guides beam placement but leads to sampling bias that favors high-U regions. Thus, although model-age histograms and relative probability plots identify zircon age populations, they are unlikely to accurately define relative abundances of age groups. Microbeam analysis collects data for the entire volume sampled but only SIMS depth-profiling into crystal faces can spatially resolve fine zones. ID-TIMS analysis of CL-imaged zircon fragments can improve U-Pb precision. SIMS complements geochronology with trace element fingerprints of zircon growth environments and enables Ti-in-zircon thermometry. Literature examples illustrate recent findings: (1) rhyodacite lava at Crater Lake contains zircons derived from late Pleistocene granodiorite represented by blocks ejected in the caldera-forming eruption; (2) zircons in Mount St. Helens dacites grew at sub-eruption temperatures and pre-date eruptions by up to 250 kyr; (3) Miocene

Atomistic Modeling of RuAl and (RuNi) Al Alloys

NASA Technical Reports Server (NTRS)

Gargano, Pablo; Mosca, Hugo; Bozzolo, Guillermo; Noebe, Ronald D.; Gray, Hugh R. (Technical Monitor)

2002-01-01

Atomistic modeling of RuAl and RuAlNi alloys, using the BFS (Bozzolo-Ferrante-Smith) method for alloys is performed. The lattice parameter and energy of formation of B2 RuAl as a function of stoichiometry and the lattice parameter of (Ru(sub 50-x)Ni(sub x)Al(sub 50)) alloys as a function of Ni concentration are computed. BFS based Monte Carlo simulations indicate that compositions close to Ru25Ni25Al50 are single phase with no obvious evidence of a miscibility gap and separation of the individual B2 phases.

Optically stimulated luminescence and thermoluminescence efficiencies for high-energy heavy charged particle irradiation in Al2O3:C.

PubMed

Yukihara, E G; Gaza, R; McKeever, S W S; Soares, C G

2004-02-01

The thermally and optically stimulated luminescence (TL and OSL) response to high energy heavy-charged particles (HCPs) was investigated for two types of Al2O3:C luminescence dosimeters. The OSL signal was measured in both continuous-wave (CW) and pulsed mode. The efficiencies of the HCPs at producing TL or OSL, relative to gamma radiation, were obtained using four different HCPs beams (150 MeV/u 4He, 400 MeV/u 12C, 490 MeV/u 28Si, and 500 MeV/u 56Fe). The efficiencies were determined as a function of the HCP linear energy transfer (LET). It was observed that the efficiency depends on the type of detector, measurement technique, and the choice of signal. Additionally, it is shown that the shape of the CW-OSL decay curve from Al2O3:C depends on the type of radiation, and, in principle, this can be used to extract information concerning the LET of an unknown radiation field. The response of the dosimeters to low-LET radiation was also investigated for doses in the range from about 1-1000 Gy. These data were used to explain the different efficiency values obtained for the different materials and techniques, as well as the LET dependence of the CW-OSL decay curve shape. c2003 Elsevier Ltd. All rights reserved.

Optically stimulated luminescence and thermoluminescence efficiencies for high-energy heavy charged particle irradiation in Al2O3:C

NASA Technical Reports Server (NTRS)

Yukihara, E. G.; Gaza, R.; McKeever, S. W. S.; Soares, C. G.

2004-01-01

The thermally and optically stimulated luminescence (TL and OSL) response to high energy heavy-charged particles (HCPs) was investigated for two types of Al2O3:C luminescence dosimeters. The OSL signal was measured in both continuous-wave (CW) and pulsed mode. The efficiencies of the HCPs at producing TL or OSL, relative to gamma radiation, were obtained using four different HCPs beams (150 MeV/u 4He, 400 MeV/u 12C, 490 MeV/u 28Si, and 500 MeV/u 56Fe). The efficiencies were determined as a function of the HCP linear energy transfer (LET). It was observed that the efficiency depends on the type of detector, measurement technique, and the choice of signal. Additionally, it is shown that the shape of the CW-OSL decay curve from Al2O3:C depends on the type of radiation, and, in principle, this can be used to extract information concerning the LET of an unknown radiation field. The response of the dosimeters to low-LET radiation was also investigated for doses in the range from about 1-1000 Gy. These data were used to explain the different efficiency values obtained for the different materials and techniques, as well as the LET dependence of the CW-OSL decay curve shape. c2003 Elsevier Ltd. All rights reserved.

Building a stable RNA U-turn with a protonated cytidine.