Ultrafine particle emissions by in-use diesel buses of various generations at low-load regimes

NASA Astrophysics Data System (ADS)

Tartakovsky, L.; Baibikov, V.; Comte, P.; Czerwinski, J.; Mayer, A.; Veinblat, M.; Zimmerli, Y.

2015-04-01

Ultrafine particles (UFP) are major contributors to air pollution due to their easy gas-like penetration into the human organism, causing adverse health effects. This study analyzes UFP emissions by buses of different technologies (from Euro II till Euro V EEV - Enhanced Environmentally-friendly Vehicle) at low-load regimes. Additionally, the emission-reduction potential of retrofitting with a diesel particle filter (DPF) is demonstrated. A comparison of the measured, engine-out, particle number concentrations (PNC) for buses of different technological generations shows that no substantial reduction of engine-out emissions at low-load operating modes is observed for newer bus generations. Retrofitting the in-use urban and interurban buses of Euro II till Euro IV technologies by the VERT-certified DPF confirmed its high efficiency in reduction of UFP emissions. Particle-count filtration efficiency values of the retrofit DPF were found to be extremely high - greater than 99.8%, similar to that of the OEM filter in the Euro V bus.

Exposure Assessment for Atmospheric Ultrafine Particles (UFPs) and Implications in Epidemiologic Research

PubMed Central

Sioutas, Constantinos; Delfino, Ralph J.; Singh, Manisha

2005-01-01

Epidemiologic research has shown increases in adverse cardiovascular and respiratory outcomes in relation to mass concentrations of particulate matter (PM) ≤2.5 or ≤10 μm in diameter (PM2.5, PM10, respectively). In a companion article [Delfino RJ, Sioutas C, Malik S. 2005. Environ Health Perspect 113(8):934–946]), we discuss epidemiologic evidence pointing to underlying components linked to fossil fuel combustion. The causal components driving the PM associations remain to be identified, but emerging evidence on particle size and chemistry has led to some clues. There is sufficient reason to believe that ultrafine particles < 0.1 μm (UFPs) are important because when compared with larger particles, they have order of magnitudes higher particle number concentration and surface area, and larger concentrations of adsorbed or condensed toxic air pollutants (oxidant gases, organic compounds, transition metals) per unit mass. This is supported by evidence of significantly higher in vitro redox activity by UFPs than by larger PM. Although epidemiologic research is needed, exposure assessment issues for UFPs are complex and need to be considered before undertaking investigations of UFP health effects. These issues include high spatial variability, indoor sources, variable infiltration of UFPs from a variety of outside sources, and meteorologic factors leading to high seasonal variability in concentration and composition, including volatility. To address these issues, investigators need to develop as well as validate the analytic technologies required to characterize the physical/chemical nature of UFPs in various environments. In the present review, we provide a detailed discussion of key characteristics of UFPs, their sources and formation mechanisms, and methodologic approaches to assessing population exposures. PMID:16079062

Impacts of exposure to black carbon, elemental carbon, and ultrafine particles from indoor and outdoor sources on blood pressure in adults: A review of epidemiological evidence.

PubMed

Magalhaes, Sandra; Baumgartner, Jill; Weichenthal, Scott

2018-02-01

Ambient particulate air pollution is known to have detrimental effects on cardiovascular health but less is known about the specific effects of black carbon or elemental carbon (BC/EC) and ultrafine particles (UFP). We present a narrative review of the epidemiological evidence related to the impact of exposure to BC/EC and UFP on blood pressure in adults. We searched PubMed and EMBASE in September 2017, using a predefined search strategy. Abstracts were screened using predefined inclusion criteria. Data collection was completed using a standard data extraction form. We focused on main effect estimates for associations between short (≤7 days) and long-term exposures to BC/EC and UFP and systolic (SBP) and diastolic blood pressure (DBP). Effect estimates were rescaled to enable direct comparisons between studies. Thirty publications were included in the review: 19 studies examined outdoor exposure to BC/EC, 11 examined outdoor UFP, three studies examined indoor BC and one study examined indoor UFP. In general, existing evidence supports a positive association between BC/EC and blood pressure. Evidence for outdoor UFP exposures were less clear as effect estimates were small in magnitude and confidence intervals often included the null. Existing evidence supports a positive association between BC/EC and blood pressure in adults, whereas UFPs do not appear to have a meaningful impact on blood pressure. Copyright © 2017 Elsevier Inc. All rights reserved.

A work group report on ultrafine particles (American Academy of Allergy, Asthma & Immunology): Why ambient ultrafine and engineered nanoparticles should receive special attention for possible adverse health outcomes in human subjects.

PubMed

Li, Ning; Georas, Steve; Alexis, Neil; Fritz, Patricia; Xia, Tian; Williams, Marc A; Horner, Elliott; Nel, Andre

2016-08-01

Ultrafine particles (UFPs) are airborne particulates of less than 100 nm in aerodynamic diameter. Examples of UFPs are diesel exhaust particles, products of cooking, heating, and wood burning in indoor environments, and, more recently, products generated through the use of nanotechnology. Studies have shown that ambient UFPs have detrimental effects on both the cardiovascular and respiratory systems, including a higher incidence of atherosclerosis and exacerbation rate of asthma. UFPs have been found to alter in vitro and in vivo responses of the immune system to allergens and can also play a role in allergen sensitization. The inflammatory properties of UFPs can be mediated by a number of different mechanisms, including the ability to produce reactive oxygen species, leading to the generation of proinflammatory cytokines and airway inflammation. In addition, because of their small size, UFPs also have unique distribution characteristics in the respiratory tree and circulation and might be able to alter cellular function in ways that circumvent normal signaling pathways. Additionally, UFPs can penetrate intracellularly and potentially cause DNA damage. The recent advances in nanotechnology, although opening up new opportunities for the advancement of technology and medicine, could also lead to unforeseen adverse health effects in exposed human subjects. Further research is needed to clarify the safety of nanoscale particles, as well as the elucidation of the possible beneficial use of these particulates to treat disease. Copyright © 2016 American Academy of Allergy, Asthma & Immunology. All rights reserved.

PEP Support Laboratory Leaching and Permeate Stability Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Renee L.; Peterson, Reid A.; Rinehart, Donald E.

2009-09-25

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes," of the External Flowsheet Review Team (EFRT) issue response plan.( ) The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes.more » The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. A simplified flow diagram of the PEP system is shown in Figure 1.1. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP and vessels UFP-VSL-00001A and B in the WTP PTF). In both scenarios, 19-M sodium hydroxide solution (NaOH, caustic) is added to the waste slurry in the vessels to leach solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by a heating step that uses direct injection of steam to accelerate the leach process. Following the caustic leach, the vessel contents are cooled using vessel cooling jackets and/or external heat exchangers. The main difference between the two scenarios is that for leaching in UFP-VSL-T01A and B, the 19-M NaOH is added to un-concentrated waste slurry (3 to 8 wt% solids), while for leaching in UFP-VSL-T02A, the slurry is concentrated to nominally 20 wt% solids using cross-flow ultrafiltration before adding caustic.« less

Retroperitoneal laparoscopy management for ureteral fibroepithelial polyps causing hydronephrosis in children: a report of five cases.

PubMed

Dai, L N; Chen, C D; Lin, X K; Wang, Y B; Xia, L G; Liu, P; Chen, X M; Li, Z R

2015-10-01

Hydronephrosis is a common disease in children and may be caused by ureteral fibroepithelial polyps (UFP). Ureteral fibroepithelial polyps are rare in children and are difficult to precisely diagnose before surgery. Surgical treatment for symptomatic UFP is recommended. At the present institution, retroperitoneal laparoscopy has been used to treat five boys with UFP since 2006. To highlight the significance of UFP as an etiological factor of hydronephrosis in children and evaluate the applicative value of retroperitoneal laparoscopy in the treatment of children with UFP. Between 2006 and 2013 five boys underwent retroperitoneal laparoscopy at the present institution. They were identified with UFP by review of the clinical database. Detailed data were collected, including: radiographic studies, gross anatomical pathology, and pathology and radiology reports. All boys had been followed up at least every 6 months. All of the boys were aged between 7 and 16 years (mean 9.8 years). The main symptoms were flank pain (all five) and hematuria (three). Radiographic examination showed that all of the boys presented with incomplete ureteral obstruction and hydronephrosis. The ureteral fibroepithelial polyps were located near the left UPJ or the left proximal ureter. All of the boys had the UFP removed: three underwent retroperitoneal laparoscopic dismembered Anderson-Hynes pyeloplasty and polypectomy, and two had retroperitoneal laparoscopic ureteral anastomosis. These polyps were all on the left side and between 15 and 35 mm in length (mean 22 mm) (Figure). All of the boys recovered well and were discharged from hospital. The postoperative histological report confirmed that the specimens were UFP. Hydronephrosis was periodically assessed by ultrasonography (using the same method as pre-surgical ultrasonography) after surgery. Mean follow-up was 33 months (range 6-58 months) and no complications were found afterwards. Ureteral fibroepithelial polyps are rare but rather important as they can cause UPJ obstruction, which often manifests as hydronephrosis. It is most important to confirm the site of ureteral obstruction before surgery as this may have an effect on the surgical management. It is recommended that UFP be successfully managed in children with retroperitoneal laparoscopy. Copyright © 2015 Journal of Pediatric Urology Company. Published by Elsevier Ltd. All rights reserved.

Spatial variations in ambient ultrafine particle concentrations and the risk of incident prostate cancer: A case-control study.

PubMed

Weichenthal, Scott; Lavigne, Eric; Valois, Marie-France; Hatzopoulou, Marianne; Van Ryswyk, Keith; Shekarrizfard, Maryam; Villeneuve, Paul J; Goldberg, Mark S; Parent, Marie-Elise

2017-07-01

Diesel exhaust contains large numbers of ultrafine particles (UFPs, <0.1µm) and is a recognized human carcinogen. However, epidemiological studies have yet to evaluate the relationship between UFPs and cancer incidence. We conducted a case-control study of UFPs and incident prostate cancer in Montreal, Canada. Cases were identified from all main Francophone hospitals in the Montreal area between 2005 and 2009. Population controls were identified from provincial electoral lists of French Montreal residents and frequency-matched to cases using 5-year age groups. UFP exposures were estimated using a land use regression model. Exposures were assigned to residential locations at the time of diagnosis/recruitment as well as approximately 10-years earlier to consider potential latency between exposure and disease onset. Odds ratios (OR) and 95% confidence intervals (95% CI) were calculated per interquartile range (IQR) increase in UFPs (approximately 4000 particles/cm 3 ) using logistic regression models adjusting for individual-level and ecological covariates. Ambient UFP concentrations were associated with an increased risk of prostate cancer (OR=1.10, 95% CI: 1.01, 1.19) in fully adjusted models when exposures were assigned to residences 10-years prior to diagnosis. This risk estimate increased slightly (OR=1.17, 95% CI; 1.01, 1.35) when modeled as a non-linear natural spline function. A smaller increased risk (OR=1.04, 95% CI: 0.97, 1.11) was observed when exposures were assigned to residences at the time of diagnosis. Exposure to ambient UFPs may increase the risk of prostate cancer. Future studies are needed to replicate this finding as this is the first study to evaluate this relationship. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.

Ambient ultrafine particle levels at residential and reference sites in urban and rural Switzerland.

PubMed

Meier, Reto; Eeftens, Marloes; Aguilera, Inmaculada; Phuleria, Harish C; Ineichen, Alex; Davey, Mark; Ragettli, Martina S; Fierz, Martin; Schindler, Christian; Probst-Hensch, Nicole; Tsai, Ming-Yi; Künzli, Nino

2015-03-03

Although there is evidence that ultrafine particles (UFP) do affect human health there are currently no legal ambient standards. The main reasons are the absence of spatially resolved exposure data to investigate long-term health effects and the challenge of defining representative reference sites for monitoring given the high dependence of UFP on proximity to sources. The objectives of this study were to evaluate the spatial distribution of UFP in four areas of the Swiss Study on Air Pollution and Lung and Heart Diseases in Adults (SAPALDIA) and to investigate the representativeness of routine air monitoring stations for residential sites in these areas. Repeated UFP measurements during three seasons have been conducted at a total of 80 residential sites and four area specific reference sites over a median duration of 7 days. Arithmetic mean residential PNC scattered around the median of 10,800 particles/cm(3) (interquartile range [IQR] = 7800 particles/cm(3)). Spatial within area contrasts (90th/10th percentile ratios) were around two; increased contrasts were observed during weekday rush-hours. Temporal UFP patterns were comparable at reference and residential sites in all areas. Our data show that central monitoring sites can represent residential conditions when locations are well chosen with respect to the local sources--namely traffic. For epidemiological research, locally resolved spatial models are needed to estimate individuals' long-term exposures to UFP of outdoor origin at home, during commute and at work.

The test of the layout of polarimeter "UFP" on the telescope AZT-2

NASA Astrophysics Data System (ADS)

Levchenko, T. A.; Nevodovskyi, P. V.; Vidmachenko, A. P.; Morozhenko, O. V.; Saryboha, H. V.; Zbrutsky, O. V.; Ivakhiv, O. V.

2016-05-01

Main Astronomical Observatory of NAS of Ukraine in cooperation with the National Technical University of Ukraine "KPI" and National University "Lviv Polytechnic" for a long time working on the design of an optical polarimeter to study of the stratospheric layer of the Earth using of orbital satellite. During this time, was accumulated a large experience of such work, and was established a layout of compact ultraviolet polarimeter (UFP) on board of satellite

Ultrafine particles from diesel vehicle emissions at different driving cycles induce differential vascular pro-inflammatory responses: Implication of chemical components and NF-κB signaling

PubMed Central

2010-01-01

Background Epidemiological evidence supports the association between exposure to ambient particulate matter (PM) and cardiovascular diseases. Chronic exposure to ultrafine particles (UFP; Dp <100 nm) is reported to promote atherosclerosis in ApoE knockout mice. Atherogenesis-prone factors induce endothelial dysfunction that contributes to the initiation and progression of atherosclerosis. We previously demonstrated that UFP induced oxidative stress via c-Jun N-terminal Kinases (JNK) activation in endothelial cells. In this study, we investigated pro-inflammatory responses of human aortic endothelial cells (HAEC) exposed to UFP emitted from a diesel truck under an idling mode (UFP1) and an urban dynamometer driving schedule (UFP2), respectively. We hypothesize that UFP1 and UFP2 with distinct chemical compositions induce differential pro-inflammatory responses in endothelial cells. Results UFP2 contained a higher level of redox active organic compounds and metals on a per PM mass basis than UFP1. While both UFP1 and UFP2 induced superoxide production and up-regulated stress response genes such as heme oxygenease-1 (HO-1), OKL38, and tissue factor (TF), only UFP2 induced the expression of pro-inflammatory genes such as IL-8 (2.8 ± 0.3-fold), MCP-1 (3.9 ± 0.4-fold), and VCAM (6.5 ± 1.1-fold) (n = 3, P < 0.05). UFP2-exposed HAEC also bound to a higher number of monocytes than UFP1-exposed HAEC (Control = 70 ± 7.5, UFP1 = 106.7 ± 12.5, UFP2 = 137.0 ± 8.0, n = 3, P < 0.05). Adenovirus NF-κB Luciferase reporter assays revealed that UFP2, but not UFP1, significantly induced NF-κB activities. NF-κB inhibitor, CAY10512, significantly abrogated UFP2-induced pro-inflammatory gene expression and monocyte binding. Conclusion While UFP1 induced higher level of oxidative stress and stress response gene expression, only UFP2, with higher levels of redox active organic compounds and metals, induced pro-inflammatory responses via NF-κB signaling. Thus, UFP with distinct chemical compositions caused differential response patterns in endothelial cells. PMID:20307321

Analysis of the chemical composition of ultrafine particles from two domestic solid biomass fired room heaters under simulated real-world use

NASA Astrophysics Data System (ADS)

Ozgen, Senem; Becagli, Silvia; Bernardoni, Vera; Caserini, Stefano; Caruso, Donatella; Corbella, Lorenza; Dell'Acqua, Manuela; Fermo, Paola; Gonzalez, Raquel; Lonati, Giovanni; Signorini, Stefano; Tardivo, Ruggero; Tosi, Elisa; Valli, Gianluigi; Vecchi, Roberta; Marinovich, Marina

2017-02-01

Two common types of wood (beech and fir) were burned in commercial pellet (11.1 kW) and wood (8.2 kW) stoves following a combustion cycle simulating the behavior of a real-world user. Ultrafine particulate matter (UFP, dp < 100 nm) was sampled with three parallel multistage impactors and analyzed for metals, main water soluble ions, anhydrosugars, total carbon, and PAH content. The measurement of the number concentration and size distribution was also performed by a fourth multistage impactor. UFP mass emission factors averaged to 424 mg/kgfuel for all the tested stove and wood type (fir, beech) combinations except for beech log burning in the wood stove (838 mg/kgfuel). Compositional differences were observed for pellets and wood UFP samples, where high TC levels characterize the wood log combustion and potassium salts are dominant in every pellet sample. Crucial aspects determining the UFP composition in the wood stove experiments are critical situations in terms of available oxygen (a lack or an excess of combustion air) and high temperatures. Whereas for the automatically controlled pellets stove local situations (e.g., hindered air-fuel mixing due to heaps of pellets on the burner pot) determine the emission levels and composition. Wood samples contain more potentially carcinogenic PAHs with respect to pellets samples. Some diagnostic ratios related to PAH isomers and anhydrosugars compiled from experimental UFP data in the present study and compared to literature values proposed for the emission source discrimination for atmospheric aerosol, extend the evaluation usually limited to higher particle size fractions also to UFP.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Josephson, Gary B.; Geeting, John GH; Bredt, Ofelia P.

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Waste Treatment Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes." The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEPmore » also includes non-prototypic ancillary equipment to support the core processing. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP; and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP; vessels UFP-VSL-00001A and B in the WTP PTF). In both scenarios, 19-M sodium hydroxide solution (NaOH, caustic) is added to the waste slurry in the vessels to leach solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by a heating step that uses direct injection of steam to accelerate the leach process. Following the caustic leach, the vessel contents are cooled using vessel cooling jackets and/or external heat exchangers. The main difference between the two scenarios is that for leaching in UFP-1, the 19-M NaOH is added to un-concentrated waste slurry (3-8 wt% solids), while for leaching in UFP-2, the slurry is concentrated to nominally 20 wt% solids using cross-flow ultrafiltration before the addition of caustic. In both scenarios, following the caustic leach, the slurry was then concentrated to 17 wt% and washed with inhibited water to remove NaOH and other soluble salts. Next, the slurry was oxidatively leached using sodium permanganate to solubilize chrome. The slurry was then washed to remove the dissolved chrome and concentrated.« less

Characterizing and predicting ultrafine particle counts in Canadian classrooms during the winter months: model development and evaluation.

PubMed

Weichenthal, Scott; Dufresne, André; Infante-Rivard, Claire; Joseph, Lawrence

2008-03-01

School classrooms are potentially important micro-environments for childhood exposures owing to the large amount of time children spend in these locations. While a number of airborne contaminants may be present in schools, to date few studies have examined ultrafine particle (0.02-1 microm) (UFP) levels in classrooms. In this study, our objective was to characterize UFP counts (cm(-3)) in classrooms during the winter months and to develop a model to predict such exposures based on ambient weather conditions and outdoor UFPs, as well as classroom characteristics such as size, temperature, relative humidity, and carbon dioxide levels. In total, UFP count data were collected on 60 occasions in 37 occupied classrooms at one elementary school and one secondary school in Pembroke, Ontario. On average, outdoor UFP levels exceeded indoor measures by 8989 cm(-3) (95% confidence interval (CI): 6382, 11596), and classroom UFP counts were similar at both schools with a combined average of 5017 cm(-3) (95% CI: 4300, 5734). Of the variables examined only wind speed and outdoor UFPs were important determinants of classrooms UFP levels. Specifically, each 10 km/h increase in wind speed corresponded to an 1873 cm(-3) (95% CI: 825, 2920) decrease in classroom UFP counts, and each 10000 cm(-3) increase in outdoor UFPs corresponded to a 1550 cm(-3) (95% CI: 930, 2171) increase in classroom UFP levels. However, high correlations between these two predictors meant that the independent effects of wind speed and outdoor UFPs could not be separated in multivariable models, and only outdoor UFP counts were included in the final predictive model. To evaluate model performance, classroom UFP counts were collected for 8 days at two new schools and compared to predicted values based on outdoor UFP measures. A moderate correlation was observed between measured and predicted classroom UFP counts (r=0.63) for both schools combined, but this relationship was not valid on days in which a strong indoor UFP source (electric kitchen stove) was active in schools. In general, our findings suggest that reasonable estimates of classroom UFP counts may be obtained from outdoor UFP data but that the accuracy of such estimates are limited in the presence of indoor UFP sources.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weichenthal, Scott; Dufresne, Andre; Infante-Rivard, Claire

School classrooms are potentially important micro-environments for childhood exposures owing to the large amount of time children spend in these locations. While a number of airborne contaminants may be present in schools, to date few studies have examined ultrafine particle (0.02-1 {mu}m) (UFP) levels in classrooms. In this study, our objective was to characterize UFP counts (cm{sup -3}) in classrooms during the winter months and to develop a model to predict such exposures based on ambient weather conditions and outdoor UFPs, as well as classroom characteristics such as size, temperature, relative humidity, and carbon dioxide levels. In total, UFP countmore » data were collected on 60 occasions in 37 occupied classrooms at one elementary school and one secondary school in Pembroke, Ontario. On average, outdoor UFP levels exceeded indoor measures by 8989 cm{sup -3} (95% confidence interval (CI): 6382, 11 596), and classroom UFP counts were similar at both schools with a combined average of 5017 cm{sup -3} (95% CI: 4300, 5734). Of the variables examined only wind speed and outdoor UFPs were important determinants of classrooms UFP levels. Specifically, each 10 km/h increase in wind speed corresponded to an 1873 cm{sup -3} (95% CI: 825, 2920) decrease in classroom UFP counts, and each 10 000 cm{sup -3} increase in outdoor UFPs corresponded to a 1550 cm{sup -3} (95% CI: 930, 2171) increase in classroom UFP levels. However, high correlations between these two predictors meant that the independent effects of wind speed and outdoor UFPs could not be separated in multivariable models, and only outdoor UFP counts were included in the final predictive model. To evaluate model performance, classroom UFP counts were collected for 8 days at two new schools and compared to predicted values based on outdoor UFP measures. A moderate correlation was observed between measured and predicted classroom UFP counts (r=0.63) for both schools combined, but this relationship was not valid on days in which a strong indoor UFP source (electric kitchen stove) was active in schools. In general, our findings suggest that reasonable estimates of classroom UFP counts may be obtained from outdoor UFP data but that the accuracy of such estimates are limited in the presence of indoor UFP sources.« less

PEP Integrated Test D Run Report Caustic and Oxidative Leaching in UFP-VSL-T02A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sevigny, Gary J.; Bredt, Ofelia P.; Burns, Carolyn A.

2009-12-11

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes" of the External Flowsheet Review Team (EFRT) issue response plan. The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. Themore » PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario (Test B and D) has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario (Test A) has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP and vessels UFP VSL-00001A and B in the WTP PTF). In Test D, 19M sodium hydroxide (NaOH, caustic) was added to the waste slurry in the UFP VSL T02 vessel after the solids were concentrated to ~20% undissolved solids. The NaOH was added to leach solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by heating to 85°C using direct injection of steam to accelerate the leach process. The main difference of Test D compared to Test B is that the leach temperature is 85°C for 24 hrs as compared to 100°C for 12 hours. The other difference is the Test D simulant had Cr in the simulant from the start of processing and Test B had Cr added to adjust the simulant composition after aluminum leaching. Following the caustic leach, the UFP-VSL-T02A vessel contents are cooled using the vessel cooling jacket. The slurry was then concentrated to 17 wt% undissolved solids and washed with inhibited water to remove NaOH and other soluble salts. Next, the slurry was oxidatively leached using sodium permanganate to solubilize chrome. The slurry was then washed to remove the dissolved chrome and concentrated.« less

Respiratory Health Effects of Ultrafine Particles in Children: A Literature Review

PubMed Central

Heinzerling, Amy; Hsu, Joy; Yip, Fuyuen

2015-01-01

By convention, airborne particles ≤0.1 μm (100 nm) are defined as ultrafine particles (UFPs). UFPs can comprise a large number of particles in particulate matter with aerodynamic diameters ≤2.5 μm (PM2.5). Despite the documented respiratory health effects of PM2.5 and concerns that UFPs might be more toxic than larger particular matter, the effects of UFPs on the respiratory system are not well-described. Even less is known about the respiratory health effects of UFPs among particularly vulnerable populations including children. We reviewed studies examining respiratory health effects of UFPs in children and identified 12 relevant articles. Most (8/12) studies measured UFP exposure using central ambient monitors, and we found substantial heterogeneity in UFP definitions and study designs. No long-term studies were identified. In single pollutant models, UFPs were associated with incident wheezing, current asthma, lower spirometric values, and asthma-related emergency department visits among children. Also, higher exhaled nitric oxide levels were positively correlated with UFP dose among children with asthma or allergy to house dust mites in 1 study. Multivariate models accounting for potential co-pollutant confounding yielded no statistically significant results. Although evidence for a relationship between UFPs and children's respiratory is accumulating, the literature remains inconclusive. Interpretation of existing data is constrained by study heterogeneity, limited accounting for UFP spatial variation, and lack of significant findings from multi-pollutant models. PMID:26783373

Workplace Measurements of Ultrafine Particles-A Literature Review.

PubMed

Viitanen, Anna-Kaisa; Uuksulainen, Sanni; Koivisto, Antti J; Hämeri, Kaarle; Kauppinen, Timo

2017-08-01

Workers are exposed to ultrafine particles (UFP) in a number of occupations. In order to summarize the current knowledge regarding occupational exposure to UFP (excluding engineered nanoparticles), we gathered information on UFP concentrations from published research articles. The aim of our study was to create a basis for future epidemiological studies that treat UFP as an exposure factor. The literature search found 72 publications regarding UFP measurements in work environments. These articles covered 314 measurement results and tabled concentrations. Mean concentrations were compared to typical urban UFP concentration level, which was considered non-occupational background concentration. Mean concentrations higher than the typical urban UFP concentration were reported in 240 workplace measurements. The results showed that workers' exposure to UFP may be significantly higher than their non-occupational exposure to background concentration alone. Mean concentrations of over 100 times the typical urban UFP concentration were reported in welding and metal industry. However, according to the results of the review, measurements of the UFP in work environments are, to date, too limited and reported too heterogeneous to allow us to draw general conclusions about workers' exposure. Harmonization of measurement strategies is essential if we are to generate more reliable and comparable data in the future. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Atmospheric ultrafine particles promote vascular calcification via the NF-κB signaling pathway

PubMed Central

Li, Rongsong; Mittelstein, David; Kam, Winnie; Pakbin, Payam; Du, Yunfeng; Tintut, Yin; Navab, Mohamad; Sioutas, Constantinos

2013-01-01

Exposure to atmospheric fine particulate matter (PM2.5) is a modifiable risk factor of cardiovascular disease. Ultrafine particles (UFP, diameter <0.1 μm), a subfraction of PM2.5, promote vascular oxidative stress and inflammatory responses. Epidemiologic studies suggest that PM exposure promotes vascular calcification. Here, we assessed whether UFP exposure promotes vascular calcification via NF-κB signaling. UFP exposure at 50 μg/ml increased alkaline phosphatase (ALP) activity by 4.4 ± 0.2-fold on day 3 (n = 3, P < 0.001) and matrix calcification by 3.5 ± 1.7-fold on day 10 (n = 4, P < 0.05) in calcifying vascular cells (CVC), a subpopulation of vascular smooth muscle cells with osteoblastic potential. Treatment of CVC with conditioned media derived from UFP-treated macrophages (UFP-CM) also led to an increase in ALP activities and matrix calcification. Furthermore, both UFP and UFP-CM significantly increased NF-κB activity, and cotreatment with an NF-κB inhibitor, JSH23, attenuated both UFP- and UFP-CM-induced ALP activity and calcification. When low-density lipoprotein receptor-null mice were exposed to UFP at 359.5 μg/m3 for 10 wk, NF-κB activation and vascular calcification were detected in the regions of aortic roots compared with control filtered air-exposed mice. These findings suggest that UFP promotes vascular calcification via activating NF-κB signaling. PMID:23242187

Exposure to ultrafine particles and respiratory hospitalisations in five European cities.

PubMed

Samoli, Evangelia; Andersen, Zorana Jovanovic; Katsouyanni, Klea; Hennig, Frauke; Kuhlbusch, Thomas A J; Bellander, Tom; Cattani, Giorgio; Cyrys, Josef; Forastiere, Francesco; Jacquemin, Bénédicte; Kulmala, Markku; Lanki, Timo; Loft, Steffen; Massling, Andreas; Tobias, Aurelio; Stafoggia, Massimo

2016-09-01

Epidemiological evidence on the associations between exposure to ultrafine particles (UFP), with aerodynamic electrical mobility diameters <100 nm, and health is limited. We gathered data on UFP from five European cities within 2001-2011 to investigate associations between short-term changes in concentrations and respiratory hospitalisations.We applied city-specific Poisson regression models and combined city-specific estimates to obtain pooled estimates. We evaluated the sensitivity of our findings to co-pollutant adjustment and investigated effect modification patterns by period of the year, age at admission and specific diagnoses.Our results for the whole time period do not support an association between UFP and respiratory hospitalisations, although we found suggestive associations among those 0-14 years old. We nevertheless report consistent adverse effect estimates during the warm period of the year, statistically significant after lag 2 when an increase by 10 000 particles per cm(3) was associated with a 4.27% (95% CI 1.68-6.92%) increase in hospitalisations. These effect estimates were robust to particles' mass or gaseous pollutants adjustment.Considering that our findings during the warm period may reflect better exposure assessment and that the main source of non-soluble UFP in urban areas is traffic, our results call for improved regulation of traffic emissions. Copyright ©ERS 2016.

Spatio-temporal variation of urban ultrafine particle number concentrations

NASA Astrophysics Data System (ADS)

Ragettli, Martina S.; Ducret-Stich, Regina E.; Foraster, Maria; Morelli, Xavier; Aguilera, Inmaculada; Basagaña, Xavier; Corradi, Elisabetta; Ineichen, Alex; Tsai, Ming-Yi; Probst-Hensch, Nicole; Rivera, Marcela; Slama, Rémy; Künzli, Nino; Phuleria, Harish C.

2014-10-01

Methods are needed to characterize short-term exposure to ultrafine particle number concentrations (UFP) for epidemiological studies on the health effects of traffic-related UFP. Our aims were to assess season-specific spatial variation of short-term (20-min) UFP within the city of Basel, Switzerland, and to develop hybrid models for predicting short-term median and mean UFP levels on sidewalks. We collected measurements of UFP for periods of 20 min (MiniDiSC particle counter) and determined traffic volume along sidewalks at 60 locations across the city, during non-rush hours in three seasons. For each monitoring location, detailed spatial characteristics were locally recorded and potential predictor variables were derived from geographic information systems (GIS). We built multivariate regression models to predict local UFP, using concurrent UFP levels measured at a suburban background station, and combinations of meteorological, temporal, GIS and observed site characteristic variables. For a subset of sites, we assessed the relationship between UFP measured on the sidewalk and at the nearby residence (i.e., home outdoor exposure on e.g. balconies). The average median 20-min UFP levels at street and urban background sites were 14,700 ± 9100 particles cm-3 and 9900 ± 8600 particles cm-3, respectively, with the highest levels occurring in winter and the lowest in summer. The most important predictor for all models was the suburban background UFP concentration, explaining 50% and 38% of the variability of the median and mean, respectively. While the models with GIS-derived variables (R2 = 0.61) or observed site characteristics (R2 = 0.63) predicted median UFP levels equally well, mean UFP predictions using only site characteristic variables (R2 = 0.62) showed a better fit than models using only GIS variables (R2 = 0.55). The best model performance was obtained by using a combination of GIS-derived variables and locally observed site characteristics (median: R2 = 0.66; mean: R2 = 0.65). The 20-min UFP concentrations measured at the sidewalk were strongly related (R2 = 0.8) to the concurrent 20-min residential UFP levels nearby. Our results indicate that median UFP can be moderately predicted by means of a suburban background site and GIS-derived traffic and land use variables. In areas and regions where large-scale GIS data are not available, the spatial distribution of traffic-related UFP may be assessed reasonably well by collecting on-site short-term traffic and land-use data.

Outdoor and indoor UFP in primary schools across Barcelona.

PubMed

Reche, C; Viana, M; Rivas, I; Bouso, L; Àlvarez-Pedrerol, M; Alastuey, A; Sunyer, J; Querol, X

2014-09-15

Indoor and outdoor measurements of real-time ultrafine particles (UFP; N10-700 in this study) number concentration and average diameter were collected twice at 39 primary schools located in Barcelona (Spain), with classrooms naturally ventilated under warm weather conditions. Simultaneous outdoor N concentration measurements at schools under different traffic exposures showed the important role of this source, with higher levels by 40% on average at schools near heavy traffic, highlighting thus the increased exposure of children due to urban planning decisions. A well-defined spatial pattern of outdoor UFP levels was observed. Midday increases in outdoor N levels mainly attributed to nucleation processes have been recorded both at high and low temperatures in several of the outdoor school sites (increasing levels by 15%-70%). The variation of these increases also followed a characteristic spatial pattern, pointing at schools' location as a key variable in terms of UFP load owing to the important contribution of traffic emissions. Indoor N concentrations were to some extent explained by outdoor N concentrations during school hours, together with average temperatures, related with natural ventilation. Outdoor midday increases were generally mimicked by indoor N concentrations, especially under warm temperatures. At specific cases, indoor concentrations during midday were 30%-40% higher than outdoor. The time scale of these observations evidenced the possible role of: a) secondary particle formation enhanced by indoor precursors or conditions, maybe related with surface chemistry reactions mediated by O3, and/or b) UFP from cooking activities. Significant indoor N increases were detected after school hours, probably associated with cleaning activities, resulting in indoor N concentrations up to 3 times higher than those in outdoor. A wide variability of indoor/outdoor ratios of N concentrations and mean UFP sizes was detected among schools and measurement periods, which seems to be partly associated with climatic conditions and O3 levels, although further research is required. Copyright © 2014 Elsevier B.V. All rights reserved.

Insights on wood combustion generated proinflammatory ultrafine particles (UFP).

PubMed

Corsini, Emanuela; Ozgen, Senem; Papale, Angela; Galbiati, Valentina; Lonati, Giovanni; Fermo, Paola; Corbella, Lorenza; Valli, Gianluigi; Bernardoni, Vera; Dell'Acqua, Manuela; Becagli, Silvia; Caruso, Donatella; Vecchi, Roberta; Galli, Corrado L; Marinovich, Marina

2017-01-15

This study aimed to collect, characterize ultrafine particles (UFP) generated from the combustion of wood pellets and logs (softwood and hardwood) and to evaluate their pro-inflammatory effects in THP-1 and A549 cells. Both cell lines responded to UFP producing interleukin-8 (IL-8), with wood log UFP being more active compared to pellet UFP. With the exception of higher effect observed with beech wood log UFP in THP-1, the ability of soft or hard woods to induce IL-8 release was similar. In addition, on weight mass, IL-8 release was similar or lower compared to diesel exhaust particles (DEP), arguing against higher biological activity of smaller size particles. UFP-induced IL-8 could be reduced by SB203580, indicating a role of p38MAPK activation in IL-8 production. The higher activity of beech wood log UFP in THP-1 was not due to higher uptake or endotoxin contamination. Qualitatively different protein adsorption profiles were observed, with less proteins bound to beech UFP compared to conifer UFP or DEP, which may provide higher intracellular availability of bioactive components, i.e. levoglucosan and galactosan, toward which THP-1 were more responsive compared to A549 cells. These results contribute to our understanding of particles emitted by domestic appliances and their biological effects. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Ultrafine particle measurement and related EPA research studies

EPA Science Inventory

Webinar slides to present information on measuring ultrafine particles at the request of the 2013 MARAMA Monitoring Committee. The talk covers near-road monitoring, instrument intercomparison, and general overview of UFP monitoring technology.

Ultra Fine Particles from Diesel Engines Induce Vascular Oxidative Stress via JNK Activation

PubMed Central

Li, Rongsong; Ning, Zhi; Cui, Jeffery; Khalsa, Bhavraj; Ai, Lisong; Takabe, Wakako; Beebe, Tyler; Majumdar, Rohit; Sioutas, Constantinos; Hsiai, Tzung

2011-01-01

Exposure of particulate air pollution is linked to increased incidences of cardiovascular diseases. Ambient ultra fine particles (UFP) from diesel vehicle engines have been shown to be pro-atherogenic in apoE knockout mice and may constitute a major cardiovascular risk in humans. We posited that circulating nano-sized particles from traffic pollution sources induced vascular oxidative stress via JNK activation in endothelial cells. Diesel UFP were collected from a 1998 Kenworth truck. Intra-cellular superoxide assay revealed that these UFP dose-dependently induced superoxide (O2·-) production in human aortic endothelial cells (HAEC). Flow cytometry (FACS) showed that UFP increased MitoSOX Red intensity specific for mitochondrial superoxide. Protein carbonyl content is increased by UFP as an indication of vascular oxidative stress. UFP also up-regulated hemeoxygenase-1 (HO-1) and tissue factor (TF) mRNA expression, and pre-treatment with antioxidant, N-acetyl cysteine (NAC), significantly decreased their expression. Furthermore, UFP transiently activated JNK in HAEC. Treatment with JNK inhibitor SP600125 and silencing of both JNK1 and JNK2 with siRNA inhibited UFP stimulated O2·- production and mRNA expression of HO-1 and TF. Our findings suggest that JNK activation play an important role in UFP-induced oxidative stress and stress response gene expression. PMID:19154785

The Effect of Ultrafine Process on the Dissolution, Antibacterial Activity, and Cytotoxicity of Coptidis rhizoma

PubMed Central

Jiang, Zhen-Yu; Deng, Hai-Ying; Yu, Zhi-Jun; Ni, Jun-Yan; Kang, Si-He

2016-01-01

Background: The dosage of herb ultrafine particle (UFP) depended on the increased level of its dissolution, toxicity, and efficacy. Objective: The dissolution, antibacterial activity, and cytotoxicity of Coptidis rhizoma (CR) UFP were compared with those of traditional decoction (TD). Materials and Methods: The dissolution of berberine (BBR) of CR TD and UFP was determined by high-performance liquid chromatography. The antibacterial activity of CR extract was assayed by plate-hole diffusion and broth dilution method; the inhibitory effect of rat serums against bacteria growth was evaluated after orally given CR UFP or TD extract. The cytotoxicity of CR extract was evaluated by 3-(4,5-dimethylthiazol-2-Yl)-2,5-diphenyltetrazolium bromide assay. Results: The dissolution amount of BBR from CR UFP increased 6–8-folds in comparison to TD at 2 min, the accumulative amount of BBR in both UFP and TD group increased in a time-dependent manner. The minimal inhibitory concentrations and minimal bactericidal concentrations of CR UFP extract decreased to 1/2~1/4 of those of TD extract. The inhibitory effect of rat serums against bacteria growth decreased time-dependently, and no statistical difference was observed between two groups at each time point. The 50% cytotoxic concentrations of UFP extract increased 1.66~1.97 fold than those of TD. Conclusions: The antibacterial activity and cytotoxicity of CR UFP increased in a dissolution-effect manner in vitro, the increased level of cytotoxicity was lower than that of antibacterial activity, and the inhibitory effect of rat serums containing drugs of UFP group did not improve. SUMMARY Ultrafine grinding process caused a rapid increase of BBR dissolution from CR.The antibacterial activity and cytotoxicity of UFP extract in vitro increased in a dissolution-effect manner, but the cytotoxicity increased lower than the antibacterial activity.The antibacterial activity of rat serums of UFP group did not improve in comparison to that of TD group PMID:26941540

Continuous Near-Road Monitoring of Ultrafine Particles from 2010-2015 in Toronto, Canada

NASA Astrophysics Data System (ADS)

Su, Y.; Sofowote, U.; Debosz, J.; Munoz, T.

2015-12-01

Ultrafine particles (UFPs) have an aerodynamic diameter less than 100 nanometre (nm). Their large surface areas per unit mass favor absorption of toxic chemicals in air. UFPs could penetrate deep into the respiratory or cardiovascular systems and pose adverse health effects. Recent studies showed the association between children exposure to UFPs and their systolic blood pressure. In urban environments, primary sources of UFPs are from road traffic emissions and account for most of the total particle numbers. Controls on UPFs rely on better understanding of their emission sources and environmental behaviour. Ontario Ministry of the Environment and Climate Change have monitored UFPs since 2010 at two near-road stations in Toronto by using TSI 3031 UFP monitors. One station is located in mixed residential and industrial area and 16 meters from a major road with over 20,000 vehicles per day. The other station is surrounded by mixed residential and commercial buildings and 20 meters from a major road with over 20,000 vehicles per day. UFPs concentrations were monitored using six size channels: 20-30nm, 30-50nm, 50-70nm, 70-100nm, 100-200nm, and 200-450nm. The TSI 3031 monitors generally performed well for long-term UFP monitoring. Multi-year measurements of UFPs at the two stations show no apparent inter-annual variation or seasonality. Smaller particles (i.e., 20-50 nm) were found to be composed of over 50% of the measured particles. The observations are generally consistent with the theoretical understanding of particle nuclei mode and accumulation mode. When air mass originated from road traffic, UFPs were elevated in morning traffic hours and to a less extent in the late afternoon. The elevated UFPs number concentrations coincided with other traffic-related air pollutants like nitrogen oxides and black carbon. Moreover, higher number concentrations were found on weekdays than weekends. The observations suggest that UFPs are mostly from vehicle emissions.

Total deposition of ultrafine particles in the lungs of healthy men and women: experimental and theoretical results

PubMed Central

2016-01-01

Background Inhaled ultrafine particles (UFP) may induce greater adverse respiratory effects than larger particles occurring in the ambient atmosphere. Due to this potential of UFP to act as triggers for diverse lung injuries medical as well as physical research has been increasingly focused on the exact deposition behavior of the particles in lungs of various probands. Main purpose of the present study was the presentation of experimental and theoretical data of total, regional, and local UFP deposition in the lungs of men and women. Methods Both experiments and theoretical simulations were carried out by using particle sizes of 0.04, 0.06, 0.08, and 0.10 µm [number median diameters (NMD)]. Inhalation of UFP took place by application of predefined tidal volumes (500, 750, and 1,000 mL) and respiratory flow rates (150, 250, 375, and 500 mL·s−1). For male subjects a functional residual capacity (FRC) of 3,911±892 mL was measured, whereas female probands had a FRC of 3,314±547 mL. Theoretical predictions were based on (I) a stochastic model of the tracheobronchial tree; (II) particle transport computations according to a random walk algorithm; and (III) empirical formulae for the description of UFP deposition. Results Total deposition fractions (TDF) are marked by a continuous diminution with increasing particle size. Whilst particles measuring 0.04 µm in size deposit in the respiratory tract by 40–70%, particles with a size of 0.10 µm exhibit deposition values ranging from 20% to 45%. Except for the largest particles studied here TDF of female probands are higher than those obtained for male probands. Differences between experimental and theoretical results are most significant for 0.10 µm particles, but never exceed 20%. Predictions of regional (extrathoracic, tracheobronchial, alveolar) UFP deposition show clearly that females tend to develop higher tracheobronchial and alveolar deposition fractions than males. This discrepancy is also confirmed by airway generation-specific deposition, which is permanently higher in women than in men. Conclusions From the experimental data and modeling predictions it can be concluded that females bear a slightly higher potential to develop lung insufficiencies after exposure to UFP than males. Besides higher deposition fractions occurring in female subjects, also total lung deposition dose is noticeably enhanced. PMID:27429960

Total deposition of ultrafine particles in the lungs of healthy men and women: experimental and theoretical results.

PubMed

Sturm, Robert

2016-06-01

Inhaled ultrafine particles (UFP) may induce greater adverse respiratory effects than larger particles occurring in the ambient atmosphere. Due to this potential of UFP to act as triggers for diverse lung injuries medical as well as physical research has been increasingly focused on the exact deposition behavior of the particles in lungs of various probands. Main purpose of the present study was the presentation of experimental and theoretical data of total, regional, and local UFP deposition in the lungs of men and women. Both experiments and theoretical simulations were carried out by using particle sizes of 0.04, 0.06, 0.08, and 0.10 µm [number median diameters (NMD)]. Inhalation of UFP took place by application of predefined tidal volumes (500, 750, and 1,000 mL) and respiratory flow rates (150, 250, 375, and 500 mL·s(-1)). For male subjects a functional residual capacity (FRC) of 3,911±892 mL was measured, whereas female probands had a FRC of 3,314±547 mL. Theoretical predictions were based on (I) a stochastic model of the tracheobronchial tree; (II) particle transport computations according to a random walk algorithm; and (III) empirical formulae for the description of UFP deposition. Total deposition fractions (TDF) are marked by a continuous diminution with increasing particle size. Whilst particles measuring 0.04 µm in size deposit in the respiratory tract by 40-70%, particles with a size of 0.10 µm exhibit deposition values ranging from 20% to 45%. Except for the largest particles studied here TDF of female probands are higher than those obtained for male probands. Differences between experimental and theoretical results are most significant for 0.10 µm particles, but never exceed 20%. Predictions of regional (extrathoracic, tracheobronchial, alveolar) UFP deposition show clearly that females tend to develop higher tracheobronchial and alveolar deposition fractions than males. This discrepancy is also confirmed by airway generation-specific deposition, which is permanently higher in women than in men. From the experimental data and modeling predictions it can be concluded that females bear a slightly higher potential to develop lung insufficiencies after exposure to UFP than males. Besides higher deposition fractions occurring in female subjects, also total lung deposition dose is noticeably enhanced.

Unsplittable Flow in Paths and Trees and Column-Restricted Packing Integer Programs

NASA Astrophysics Data System (ADS)

Chekuri, Chandra; Ene, Alina; Korula, Nitish

We consider the unsplittable flow problem (UFP) and the closely related column-restricted packing integer programs (CPIPs). In UFP we are given an edge-capacitated graph G = (V,E) and k request pairs R 1, ..., R k , where each R i consists of a source-destination pair (s i ,t i ), a demand d i and a weight w i . The goal is to find a maximum weight subset of requests that can be routed unsplittably in G. Most previous work on UFP has focused on the no-bottleneck case in which the maximum demand of the requests is at most the smallest edge capacity. Inspired by the recent work of Bansal et al. [3] on UFP on a path without the above assumption, we consider UFP on paths as well as trees. We give a simple O(logn) approximation for UFP on trees when all weights are identical; this yields an O(log2 n) approximation for the weighted case. These are the first non-trivial approximations for UFP on trees. We develop an LP relaxation for UFP on paths that has an integrality gap of O(log2 n); previously there was no relaxation with o(n) gap. We also consider UFP in general graphs and CPIPs without the no-bottleneck assumption and obtain new and useful results.

Assessment of ultrafine particles in Portuguese preschools: levels and exposure doses.

PubMed

Fonseca, J; Slezakova, K; Morais, S; Pereira, M C

2014-12-01

The aim of this work was to assess ultrafine particles (UFP) number concentrations in different microenvironments of Portuguese preschools and to estimate the respective exposure doses of UFP for 3-5-year-old children (in comparison with adults). UFP were sampled both indoors and outdoors in two urban (US1, US2) and one rural (RS1) preschool located in north of Portugal for 31 days. Total levels of indoor UFP were significantly higher at the urban preschools (mean of 1.82 × 10(4) and 1.32 × 10(4) particles/cm(3) at US1 an US2, respectively) than at the rural one (1.15 × 10(4) particles/cm(3) ). Canteens were the indoor microenvironment with the highest UFP (mean of 5.17 × 10(4) , 3.28 × 10(4) , and 4.09 × 10(4) particles/cm(3) at US1, US2, and RS1), whereas the lowest concentrations were observed in classrooms (9.31 × 10(3) , 11.3 × 10(3) , and 7.14 × 10(3) particles/cm(3) at US1, US2, and RS1). Mean indoor/outdoor ratios (I/O) of UFP at three preschools were lower than 1 (0.54-0.93), indicating that outdoor emissions significantly contributed to UFP indoors. Significant correlations were obtained between temperature, wind speed, relative humidity, solar radiation, and ambient UFP number concentrations. The estimated exposure doses were higher in children attending urban preschools; 3-5-year-old children were exposed to 4-6 times higher UFP doses than adults with similar daily schedules. This study reports information on ultrafine particles (UFPs) in various indoor and outdoor microenvironments (canteens, classrooms, gymnasiums, and outdoor) of urban and rural preschools. It identifies the potential sources and origins, characterizes the influence of meteorological parameters on UFP levels, and performs a comparison with other existing international studies. To this date, relatively few studies have investigated UFP in preschools (none in Portugal) and none assessed exposure dose for different age-groups. The obtained findings showed that levels of UFP in various microenvironments of schools differed significantly. Therefore, to obtain an accurate representation of child’s overall preschool exposure profiles, the exposures occurring in these different microenvironments should be always accounted for. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

The chemical composition of ultrafine particles and associated biological effects at an alpine town impacted by wood burning.

PubMed

Corsini, Emanuela; Vecchi, Roberta; Marabini, Laura; Fermo, Paola; Becagli, Silvia; Bernardoni, Vera; Caruso, Donatella; Corbella, Lorenza; Dell'Acqua, Manuela; Galli, Corrado L; Lonati, Giovanni; Ozgen, Senem; Papale, Angela; Signorini, Stefano; Tardivo, Ruggero; Valli, Gianluigi; Marinovich, Marina

2017-06-01

This work is part of the TOBICUP (TOxicity of BIomass Combustion generated Ultrafine Particles) project which aimed at providing the composition of ultrafine particles (UFPs, i.e. particles with aerodynamic diameter, d ae , lower than 100nm) emitted by wood combustion and elucidating the related toxicity. Results here reported are from two ambient monitoring campaigns carried out at an alpine town in Northern Italy, where wood burning is largely diffused for domestic heating in winter. Wintertime and summertime UFP samples were analyzed to assess their chemical composition (i.e. elements, ions, total carbon, anhydrosugars, and polycyclic aromatic hydrocarbons) and biological activity. The induction of the pro-inflammatory cytokine interleukin-8 (IL-8) by UFPs was investigated in two human cells lines (A549 and THP-1) and in human peripheral blood leukocytes. In addition, UFP-induced oxidative stress and genotoxicity were investigated in A549 cells. Ambient UFP-related effects were compared to those induced by traffic-emitted particles (DEP) taken from the NIES reference material "vehicle exhaust particulates". Ambient air UFPs induced a dose-related IL-8 release in both A549 and THP-1 cells; the effect was more relevant on summer samples and in general THP-1 cells were more sensitive than A549 cells. On a weight basis our data did not support a higher biological activity of ambient UFPs compared to DEP. The production of IL-8 in the whole blood assay indicated that UFPs reached systemic circulation and activated blood leukocytes. Comet assay and γ-H2AX evaluation showed a significant DNA damage especially in winter UFPs samples compared to control samples. Our study showed that ambient UFPs can evoke a pulmonary inflammatory response by inducing a dose-related IL-8 production and DNA damage, with different responses to UFP samples collected in the summer and winter periods. Copyright © 2017 Elsevier B.V. All rights reserved.

Contributions of aircraft arrivals and departures to ultrafine particle counts near Los Angeles International Airport.

PubMed

Hsu, Hsiao-Hsien; Adamkiewicz, Gary; Houseman, E Andres; Zarubiak, Darcy; Spengler, John D; Levy, Jonathan I

2013-02-01

While commercial aircraft are known sources of ultrafine particulate matter (UFP), the relationship between airport activity and local real-time UFP concentrations has not been quantified. Understanding these associations will facilitate interpretation of the exposure and health risk implications of UFP related to aviation emissions. We used time-resolved UFP data along with flight activity and meteorological information to determine the contributions of aircraft departures and arrivals to UFP concentrations. Aircraft flight activity and near-field continuous UFP concentrations (≧ 6 nm) were measured at five monitoring sites over a 42-day field campaign at Los Angeles International Airport (LAX). We developed regression models of UFP concentrations as a function of time-lagged landing and take-off operations (LTO) activity, in the form of arrivals or departures weighted by engine-specific estimates of fuel consumption. Our regression models demonstrate a strong association between departures and elevated total UFP concentrations at the end of the departure runway, with diminishing magnitude and time-lagged impacts with distance from the source. LTO activity contributed a median (95th, 99th percentile) UFP concentration of approximately 150,000 particles/cm(3) (2,000,000, 7,100,000) at a monitor at the end of the departure runway, versus 19,000 particles/cm(3) (80,000, 140,000), and 17,000 particles/cm(3) (50,000, 72,000) for monitors 250 m and 500 m further downwind, respectively. We demonstrated significant contributions from aircraft departure activities to UFP concentrations in close proximity to departure runways, with evidence of rapid plume evolution in the near field. Our methods can inform source attribution and interpretation of dispersion modeling outputs. Copyright © 2012 Elsevier B.V. All rights reserved.

Ultrafine particles in cities.

PubMed

Kumar, Prashant; Morawska, Lidia; Birmili, Wolfram; Paasonen, Pauli; Hu, Min; Kulmala, Markku; Harrison, Roy M; Norford, Leslie; Britter, Rex

2014-05-01

Ultrafine particles (UFPs; diameter less than 100 nm) are ubiquitous in urban air, and an acknowledged risk to human health. Globally, the major source for urban outdoor UFP concentrations is motor traffic. Ongoing trends towards urbanisation and expansion of road traffic are anticipated to further increase population exposure to UFPs. Numerous experimental studies have characterised UFPs in individual cities, but an integrated evaluation of emissions and population exposure is still lacking. Our analysis suggests that the average exposure to outdoor UFPs in Asian cities is about four-times larger than that in European cities but impacts on human health are largely unknown. This article reviews some fundamental drivers of UFP emissions and dispersion, and highlights unresolved challenges, as well as recommendations to ensure sustainable urban development whilst minimising any possible adverse health impacts. Copyright © 2014 Elsevier Ltd. All rights reserved.

Exposure of Children to Ultrafine Particles in Primary Schools in Portugal.

PubMed

Rufo, João Cavaleiro; Madureira, Joana; Paciência, Inês; Slezakova, Klara; Pereira, Maria do Carmo; Pereira, Cristiana; Teixeira, João Paulo; Pinto, Mariana; Moreira, André; Fernandes, Eduardo de Oliveira

2015-01-01

Children spend a large part of their time at schools, which might be reflected as chronic exposure. Ultrafine particles (UFP) are generally associated with a more severe toxicity compared to fine and coarse particles, due to their ability to penetrate cell membranes. In addition, children tend to be more susceptible to UFP-mediated toxicity compared to adults, due to various factors including undeveloped immune and respiratory systems and inhalation rates. Thus, the purpose of this study was to determine indoor UFP number concentrations in Portuguese primary schools. Ultrafine particles were sampled between January and March 2014 in 10 public primary schools (35 classrooms) located in Porto, Portugal. Overall, the average indoor UFP number concentrations were not significantly different from outdoor concentrations (8.69 × 10(3) vs. 9.25 × 10(3) pt/cm(3), respectively; considering 6.5 h of indoor occupancy). Classrooms with distinct characteristics showed different trends of indoor UFP concentrations. The levels of carbon dioxide were negatively correlated with indoor UFP concentrations. Occupational density was significantly and positively correlated with UFP concentrations. Although the obtained results need to be interpreted with caution since there are no guidelines for UFP levels, special attention needs to be given to source control strategies in order to reduce major particle emissions and ensure good indoor air quality.

Ultrafine particle air pollution inside diesel-propelled passenger trains.

PubMed

Abramesko, Victoria; Tartakovsky, Leonid

2017-07-01

Locomotives with diesel engines are used worldwide and are an important source of air pollution. Pollutant emissions by locomotive engines affect the air quality inside passenger trains. This study is aimed at investigating ultrafine particle (UFP) air pollution inside passenger trains and providing a basis for assessing passenger exposure to this pollutant. The concentrations of UFPs inside the carriages of push-pull trains are dramatically higher when the train operates in pull mode. This clearly shows that locomotive engine emissions are a dominant factor in train passengers' exposure to UFPs. The highest levels of UFP air pollution are observed inside the carriages of pull trains close to the locomotive. In push mode, the UFP number concentrations were lower by factors of 2.6-43 (depending on the carriage type) compared to pull mode. The UFP concentrations are substantially lower in diesel multiple-unit trains than in trains operating in pull mode. A significant influence of the train movement regime on the UFP NC inside a carriage is observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

EFRT M12 Issue Resolution: Comparison of PEP and Bench-Scale Oxidative Leaching Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rapko, Brian M.; Brown, Christopher F.; Eslinger, Paul W.

2009-08-14

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed and constructed and is to be operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes.” The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processesmore » using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP; and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP; vessels UFP-VSL-00001A and B in the WTP PTF). In both scenarios, 19-M sodium hydroxide solution (NaOH, caustic) is added to the waste slurry in the vessels to dissolve solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by a heating step that uses direct steam injection to accelerate the leaching process. Following the caustic leach, the vessel contents are cooled using vessel cooling jackets and/or external heat exchangers. The main difference between the two scenarios is that for leaching in UFP1, the 19-M NaOH is added to un-concentrated waste slurry (3 to 8 wt% solids), while for leaching in UFP2, the slurry is concentrated to nominally 20 wt% solids using cross-flow ultrafiltration before the addition of caustic. For wastes that have significantly high chromium content, the caustic leaching and slurry dewatering is followed by adding sodium permanganate to UFP-VSL-T02A, and the slurry is subjected to oxidative leaching at nominally ambient temperature. The purpose of the oxidative leaching is to selectively oxidize the poorly alkaline-soluble Cr(III) believed to be the insoluble form in Hanford tank sludge to the much more alkaline-soluble Cr(VI), e.g., chromate. The work described in this report provides the test results that are related to the efficiency of the oxidative leaching process to support process modeling based on tests performed with a Hanford waste simulant. The tests were completed both at the lab-bench scale and in the PEP. The purpose of this report is to summarize the results from both scales that are related to oxidative leaching chemistry to support a scale factor for the submodels to be used in the G2 model, which predicts WTP operating performance. Owing to schedule constraints, the PEP test data to be included in this report are limited to those from Integrated Tests A (T01 A/B caustic leaching) and B (T02A caustic leaching).« less

Estimation of ultrafine particle concentrations at near-highway residences using data from local and central monitors

PubMed Central

Fuller, Christina H.; Brugge, Doug; Williams, Paige; Mittleman, Murray; Durant, John L.; Spengler, John D.

2012-01-01

Ultrafine particles (UFP; aerodynamic diameter < 0.1 micrometers) are a ubiquitous exposure in the urban environment and are elevated near highways. Most epidemiological studies of UFP health effects use central site monitoring data, which may misclassify exposure. Our aims were to: (1) examine the relationship between distant and proximate monitoring sites and their ability to predict hourly UFP concentration measured at residences in an urban community with a major interstate highway and; (2) determine if meteorology and proximity to traffic improve explanatory power. Short-term (1 – 3 weeks) residential monitoring of UFP concentration was conducted at 18 homes. Long-term monitoring was conducted at two near-highway monitoring sites and a central site. We created models of outdoor residential UFP concentration based on concentrations at the near-highway site, at the central site, at both sites together and without fixed sites. UFP concentration at residential sites was more highly correlated with those at a near-highway site than a central site. In regression models of each site alone, a 10% increase in UFP concentration at a near-highway site was associated with a 6% (95% CI: 6%, 7%) increase at residences while a 10% increase in UFP concentration at the central site was associated with a 3% (95% CI: 2%, 3%) increase at residences. A model including both sites showed minimal change in the magnitude of the association between the near-highway site and the residences, but the estimated association with UFP concentration at the central site was substantially attenuated. These associations remained after adjustment for other significant predictors of residential UFP concentration, including distance from highway, wind speed, wind direction, highway traffic volume and precipitation. The use of a central site as an estimate of personal exposure for populations near local emissions of traffic-related air pollutants may result in exposure misclassification. PMID:23645993

Estimation of ultrafine particle concentrations at near-highway residences using data from local and central monitors.

PubMed

Fuller, Christina H; Brugge, Doug; Williams, Paige; Mittleman, Murray; Durant, John L; Spengler, John D

2012-09-01

Ultrafine particles (UFP; aerodynamic diameter < 0.1 micrometers) are a ubiquitous exposure in the urban environment and are elevated near highways. Most epidemiological studies of UFP health effects use central site monitoring data, which may misclassify exposure. Our aims were to: (1) examine the relationship between distant and proximate monitoring sites and their ability to predict hourly UFP concentration measured at residences in an urban community with a major interstate highway and; (2) determine if meteorology and proximity to traffic improve explanatory power. Short-term (1 - 3 weeks) residential monitoring of UFP concentration was conducted at 18 homes. Long-term monitoring was conducted at two near-highway monitoring sites and a central site. We created models of outdoor residential UFP concentration based on concentrations at the near-highway site, at the central site, at both sites together and without fixed sites. UFP concentration at residential sites was more highly correlated with those at a near-highway site than a central site. In regression models of each site alone, a 10% increase in UFP concentration at a near-highway site was associated with a 6% (95% CI: 6%, 7%) increase at residences while a 10% increase in UFP concentration at the central site was associated with a 3% (95% CI: 2%, 3%) increase at residences. A model including both sites showed minimal change in the magnitude of the association between the near-highway site and the residences, but the estimated association with UFP concentration at the central site was substantially attenuated. These associations remained after adjustment for other significant predictors of residential UFP concentration, including distance from highway, wind speed, wind direction, highway traffic volume and precipitation. The use of a central site as an estimate of personal exposure for populations near local emissions of traffic-related air pollutants may result in exposure misclassification.

Ambient ultrafine particles reduce endothelial nitric oxide production via S-glutathionylation of eNOS.

PubMed

Du, Yunfeng; Navab, Mohamad; Shen, Melody; Hill, James; Pakbin, Payam; Sioutas, Constantinos; Hsiai, Tzung K; Li, Rongsong

2013-07-05

Exposure to airborne particulate pollutants is intimately linked to vascular oxidative stress and inflammatory responses with clinical relevance to atherosclerosis. Particulate matter (PM) has been reported to induce endothelial dysfunction and atherosclerosis. Here, we tested whether ambient ultrafine particles (UFP, diameter <200 nm) modulate eNOS activity in terms of nitric oxide (NO) production via protein S-glutathionylation. Treatment of human aortic endothelial cells (HAEC) with UFP significantly reduced NO production. UFP-mediated reduction in NO production was restored in the presence of JNK inhibitor (SP600125), NADPH oxidase inhibitor (Apocynin), anti-oxidant (N-acetyl cysteine), and superoxide dismutase mimetics (Tempol and MnTMPyP). UFP exposure increased the GSSG/GSH ratio and eNOS S-glutathionylation, whereas over-expression of Glutaredoxin-1 (to inhibit S-glutathionylation) restored UFP-mediated reduction in NO production by nearly 80%. Thus, our findings suggest that eNOS S-glutathionylation is a potential mechanism underlying ambient UFP-induced reduction of NO production. Copyright © 2013 Elsevier Inc. All rights reserved.

Ambient ultrafine particles reduce endothelial nitric oxide production via S-glutathionylation of eNOS

PubMed Central

Du, Yunfeng; Navab, Mohamad; Shen, Melody; Hill, James; Pakbin, Payam; Sioutas, Constantinos; Hsiai, Tzung; Li, Rongsong

2013-01-01

Exposure to airborne particulate pollutants is intimately linked to vascular oxidative stress and inflammatory responses with clinical relevance to atherosclerosis. Particulate matter (PM) has been reported to induce endothelial dysfunction and atherosclerosis. Here, we tested whether ambient ultrafine particles (UFP, diameter < 200 nm) modulate eNOS activity in terms of nitric oxide (NO) production via protein S-glutathionylation. Treatment of human aortic endothelial cells (HAEC) with UFP significantly reduced NO production. UFP-mediated reduction in NO production was restored in the presence of JNK inhibitor (SP600125), NADPH oxidase inhibitor (Apocynin), anti-oxidant (N-acetyl cysteine), and superoxide dismutase mimetics (Tempol and MnTMPyP). UFP exposure increased the GSSG/GSH ratio and eNOS S-glutathionylation, whereas over-expression of Glutaredoxin-1 (to inhibit S-glutathionylation) restored UFP-mediated reduction in NO production by nearly 80%. Thus, our findings suggest that eNOS S-glutathionylation is a potential mechanism underlying ambient UFP-induced reduction of NO production. PMID:23751346

Comparing conventional Descriptive Analysis and Napping®-UFP against physiochemical measurements: a case study using apples.

PubMed

Pickup, William; Bremer, Phil; Peng, Mei

2018-03-01

The extensive time and cost associated with conventional sensory profiling methods has spurred sensory researchers to develop rapid method alternatives, such as Napping® with Ultra-Flash Profiling (UFP). Napping®-UFP generates sensory maps by requiring untrained panellists to separate samples based on perceived sensory similarities. Evaluations of this method have been restrained to manufactured/formulated food models, and predominantly structured on comparisons against the conventional descriptive method. The present study aims to extend the validation of Napping®-UFP (N = 72) to natural biological products; and to evaluate this method against Descriptive Analysis (DA; N = 8) with physiochemical measurements as an additional evaluative criterion. The results revealed that sample configurations generated by DA and Napping®-UFP were not significantly correlated (RV = 0.425, P = 0.077); however, they were both correlated with the product map generated based on the instrumental measures (P < 0.05). The finding also noted that sample characterisations from DA and Napping®-UFP were driven by different sensory attributes, indicating potential structural differences between these two methods in configuring samples. Overall, these findings lent support for the extended use of Napping®-UFP for evaluations of natural biological products. Although DA was shown to be a better method for establishing sensory-instrumental relationships, Napping®-UFP exhibited strengths in generating informative sample configurations based on holistic perception of products. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Ultrafine particles from power plants: Evaluation of WRF-Chem simulations with airborne measurements

NASA Astrophysics Data System (ADS)

Forkel, Renate; Junkermann, Wolfgang

2017-04-01

Ultrafine particles (UFP, particles with a diameter < 100 nm) are an acknowledged risk to human health and have a potential effect on climate as their presence affects the number concentration of cloud condensation nuclei. Despite of the possibly hazardous effects no regulations exist for this size class of ambient air pollution particles. While ground based continuous measurements of UFP are performed in Germany at several sites (e.g. the German Ultrafine Aerosol Network GUAN, Birmili et al. 2016, doi:10.5194/essd-8-355-2016) information about the vertical distribution of UFP within the atmospheric boundary layer is only scarce. This gap has been closed during the last years by regional-scale airborne surveys for UFP concentrations and size distributions over Germany (Junkermann et al., 2016, doi: 10.3402/tellusb.v68.29250) and Australia (Junkermann and Hacker, 2015, doi: 10.3402/tellusb.v67.25308). Power stations and refineries have been identified as a major source of UFP in Germany with observed particle concentrations > 50000 particles cm-3 downwind of these elevated point sources. Nested WRF-Chem simulations with 2 km grid width for the innermost domain are performed with UFP emission source strengths derived from the measurements in order to study the advection and vertical exchange of UFP from power plants near the Czech and Polish border and their impact on planetary boundary layer particle patterns. The simulations are evaluated against the airborne observations and the downward mixing of the UFP from the elevated sources is studied.

[Adverse effects of ultrafine particles on the cardiovascular system and its mechanisms].

PubMed

Yi, Tie-ci; Li, Jian-ping

2014-12-18

Cardiovascular disease is one of the major threats to human. Air pollution, which , as it become a problem too serious to be ignored in China, is known to be an important risk factor for cardiovascular disease. Among all pollutants, ultrafine particles ( UFPs) , defined as particles with their diameter less than 0. 1 f.Lm, are a specific composition. They are very small in size, large in quantity and surface area, and most important, capable of passing through the air-blood barrier. These unique features of UFPs make them special in their impact on cardiovascular system. Nowadays, the influence of UFPs on the cardiovascular system has become a hot topic. On the one side, studies have shown that UFPs can cause inflammation and oxidative stress in the lung, and then induce systemic inflammation by releasing cytokine and reactive oxygen species into the circulation. On the other side, UFPs themselves can "spillout"into the circulation and interact with their targets. By this way, UFPs directly affect endothelial cells, myocardial cells and the autonomic nervous system, which ultimately result in increased cardiovascular events. We intend to make an overview about the recent progress about the influence of UFPs on human cardiovascular disease and the related mechanisms, and argue for more attention to this issue.

Transcriptional profiling of human bronchial epithelial cell BEAS-2B exposed to diesel and biomass ultrafine particles.

PubMed

Grilli, Andrea; Bengalli, Rossella; Longhin, Eleonora; Capasso, Laura; Proverbio, Maria Carla; Forcato, Mattia; Bicciato, Silvio; Gualtieri, Maurizio; Battaglia, Cristina; Camatini, Marina

2018-04-27

Emissions from diesel vehicles and biomass burning are the principal sources of primary ultrafine particles (UFP). The exposure to UFP has been associated to cardiovascular and pulmonary diseases, including lung cancer. Although many aspects of the toxicology of ambient particulate matter (PM) have been unraveled, the molecular mechanisms activated in human cells by the exposure to UFP are still poorly understood. Here, we present an RNA-seq time-course experiment (five time point after single dose exposure) used to investigate the differential and temporal changes induced in the gene expression of human bronchial epithelial cells (BEAS-2B) by the exposure to UFP generated from diesel and biomass combustion. A combination of different bioinformatics tools (EdgeR, next-maSigPro and reactome FI app-Cytoscape and prioritization strategies) facilitated the analyses the temporal transcriptional pattern, functional gene set enrichment and gene networks related to cellular response to UFP particles. The bioinformatics analysis of transcriptional data reveals that the two different UFP induce, since the earliest time points, different transcriptional dynamics resulting in the activation of specific genes. The functional enrichment of differentially expressed genes indicates that the exposure to diesel UFP induces the activation of genes involved in TNFα signaling via NF-kB and inflammatory response, and hypoxia. Conversely, the exposure to ultrafine particles from biomass determines less distinct modifications of the gene expression profiles. Diesel UFP exposure induces the secretion of biomarkers associated to inflammation (CCXL2, EPGN, GREM1, IL1A, IL1B, IL6, IL24, EREG, VEGF) and transcription factors (as NFE2L2, MAFF, HES1, FOSL1, TGIF1) relevant for cardiovascular and lung disease. By means of network reconstruction, four genes (STAT3, HIF1a, NFKB1, KRAS) have emerged as major regulators of transcriptional response of bronchial epithelial cells exposed to diesel exhaust. Overall, this work highlights modifications of the transcriptional landscape in human bronchial cells exposed to UFP and sheds new lights on possible mechanisms by means of which UFP acts as a carcinogen and harmful factor for human health.

Estimate of main local sources to ambient ultrafine particle number concentrations in an urban area

NASA Astrophysics Data System (ADS)

Rahman, Md Mahmudur; Mazaheri, Mandana; Clifford, Sam; Morawska, Lidia

2017-09-01

Quantifying and apportioning the contribution of a range of sources to ultrafine particles (UFPs, D < 100 nm) is a challenge due to the complex nature of the urban environments. Although vehicular emissions have long been considered one of the major sources of ultrafine particles in urban areas, the contribution of other major urban sources is not yet fully understood. This paper aims to determine and quantify the contribution of local ground traffic, nucleated particle (NP) formation and distant non-traffic (e.g. airport, oil refineries, and seaport) sources to the total ambient particle number concentration (PNC) in a busy, inner-city area in Brisbane, Australia using Bayesian statistical modelling and other exploratory tools. The Bayesian model was trained on the PNC data on days where NP formations were known to have not occurred, hourly traffic counts, solar radiation data, and smooth daily trend. The model was applied to apportion and quantify the contribution of NP formations and local traffic and non-traffic sources to UFPs. The data analysis incorporated long-term measured time-series of total PNC (D ≥ 6 nm), particle number size distributions (PSD, D = 8 to 400 nm), PM2.5, PM10, NOx, CO, meteorological parameters and traffic counts at a stationary monitoring site. The developed Bayesian model showed reliable predictive performances in quantifying the contribution of NP formation events to UFPs (up to 4 × 104 particles cm- 3), with a significant day to day variability. The model identified potential NP formation and no-formations days based on PNC data and quantified the sources contribution to UFPs. Exploratory statistical analyses show that total mean PNC during the middle of the day was up to 32% higher than during peak morning and evening traffic periods, which were associated with NP formation events. The majority of UFPs measured during the peak traffic and NP formation periods were between 30-100 nm and smaller than 30 nm, respectively. To date, this is the first application of Bayesian model to apportion different sources contribution to UFPs, and therefore the importance of this study is not only in its modelling outcomes but in demonstrating the applicability and advantages of this statistical approach to air pollution studies.

Comparison between ultrafine and fine particulate matter collected in Lebanon: Chemical characterization, in vitro cytotoxic effects and metabolizing enzymes gene expression in human bronchial epithelial cells.

PubMed

Borgie, Mireille; Dagher, Zeina; Ledoux, Frédéric; Verdin, Anthony; Cazier, Fabrice; Martin, Perrine; Hachimi, Adam; Shirali, Pirouz; Greige-Gerges, Hélène; Courcot, Dominique

2015-10-01

During the last few years, the induction of toxicological mechanisms by atmospheric ultrafine particles (UFP) has become one of the most studied topics in toxicology and a subject of huge debates. Fine particles (FP) and UFP collected at urban and rural sites in Lebanon were studied for their chemical composition and toxicological effects. UFP were found more enriched in trace elements, secondary inorganic ions, total carbon and organic compounds than FP. For toxicological analysis, BEAS-2B cells were exposed for 24, 48 and 72 h to increasing concentrations of FP, water-UFP suspension (UFPw) and UFP organic extract (UFPorg). Our findings showed that UFP caused earlier alterations of mitochondrial metabolism and membrane integrity from the lowest concentrations. Moreover, a significant induction of CYP1A1, CYP1B1 and AhRR genes expression was showed after cells exposure to UFPorg and to a lesser extent to UFPw and FP samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

Linking In-Vehicle Ultrafine Particle Exposures to On-Road Concentrations

PubMed Central

Hudda, Neelakshi; Eckel, Sandrah P.; Knibbs, Luke D.; Sioutas, Constantinos; Delfino, Ralph J.; Fruin, Scott A.

2013-01-01

For traffic-related pollutants like ultrafine particles (UFP, Dp < 100 nm), a significant fraction of overall exposure occurs within or close to the transit microenvironment. Therefore, understanding exposure to these pollutants in such microenvironments is crucial to accurately assessing overall UFP exposure. The aim of this study was to develop models for predicting in-cabin UFP concentrations if roadway concentrations are known, taking into account vehicle characteristics, ventilation settings, driving conditions and air exchange rates (AER). Particle concentrations and AER were measured in 43 and 73 vehicles, respectively, under various ventilation settings and driving speeds. Multiple linear regression (MLR) and generalized estimating equation (GEE) regression models were used to identify and quantify the factors that determine inside-to-outside (I/O) UFP ratios and AERs across a full range of vehicle types and ages. AER was the most significant determinant of UFP I/O ratios, and was strongly influenced by ventilation setting (recirculation or outside air intake). Inclusion of ventilation fan speed, vehicle age or mileage, and driving speed explained greater than 79% of the variability in measured UFP I/O ratios. PMID:23888122

Short-term exposure to PM 10, PM 2.5, ultrafine particles and CO 2 for passengers at an intercity bus terminal

NASA Astrophysics Data System (ADS)

Cheng, Yu-Hsiang; Chang, Hsiao-Peng; Hsieh, Cheng-Ju

2011-04-01

The Taipei Bus Station is the main transportation hub for over 50 bus routes to eastern, central, and southern Taiwan. Daily traffic volume at this station is about 2500 vehicles, serving over 45,000 passengers daily. The station is a massive 24-story building housing a bus terminal, a business hotel, a shopping mall, several cinemas, offices, private residential suites, and over 900 parking spaces. However, air quality inside this bus terminal is a concern as over 2500 buses are scheduled to run daily. This study investigates the PM 10, PM 2.5, UFP and CO 2 levels inside and outside the bus terminal. All measurements were taken between February and April 2010. Measurement results show that coarse PM inside the bus terminal was resuspended by the movement of large numbers of passengers. The fine and ultrafine PM in the station concourse were from outside vehicles. Moreover, fine and ultrafine PM at waiting areas were exhausted directly from buses in the building. The CO 2 levels at waiting areas were likely elevated by bus exhaust and passengers exhaling. The PM 10, PM 2.5 and CO 2 levels at the bus terminal were lower than Taiwan's EPA suggested standards for indoor air quality. However, UFP levels at the bus terminal were significantly higher than those in the urban background by about 10 times. Therefore, the effects of UFPs on the health of passengers and workers must be addressed at this bus terminal since the levels of UFPs are higher than >1.0 × 10 5 particles cm -3.

Near roadway air pollution across a spatially extensive road and cycling network.

PubMed

Farrell, William; Weichenthal, Scott; Goldberg, Mark; Valois, Marie-France; Shekarrizfard, Maryam; Hatzopoulou, Marianne

2016-05-01

This study investigates the variability in near-road concentrations of ultra-fine particles (UFP). Our results are based on a mobile data collection campaign conducted in 2012 in Montreal, Canada using instrumented bicycles and covering approximately 475 km of unique roadways. The spatial extent of the data collected included a diverse array of roads and land use patterns. Average concentrations of UFP per roadway segment varied greatly across the study area (1411-192,340 particles/cm(3)) as well as across the different visits to the same segment. Mixed effects linear regression models were estimated for UFP (R(2) = 43.80%), incorporating a wide range of predictors including land-use, built environment, road characteristics, and meteorology. Temperature and wind speed had a large negative effect on near-road concentrations of UFP. Both the day of the week and time of day had a significant effect with Tuesdays and afternoon periods positively associated with UFP. Since UFP are largely associated with traffic emissions and considering the wide spatial extent of our data collection campaign, it was impossible to collect traffic volume data. For this purpose, we used simulated data for traffic volumes and speeds across the region and observed a positive effect for volumes and negative effect for speed. Finally, proximity to truck routes was also associated with higher UFP concentrations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Laboratory Tests on Post-Filtration Precipitation in the WTP Pretreatment Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Renee L.; Peterson, Reid A.; Rinehart, Donald E.

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes," of the External Flowsheet Review Team (EFRT) issue response plan (Barnes et al. 2006). The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, andmore » slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. A simplified flow diagram of the PEP system is shown in Figure 1.1. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP; and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP; vessels UFP-VSL-00001A and B in the WTP PTF).« less

Assessing and reducing fine and ultrafine particles inside Los Angeles taxis

NASA Astrophysics Data System (ADS)

Yu, Nu; Shu, Shi; Lin, Yan; Zhu, Yifang

2018-05-01

Taxi drivers and passengers are exposed to high levels of traffic-related air pollutants, but their exposures to fine (PM2.5) and ultrafine particles (UFPs) and related mitigation strategies are rarely explored. In this study, UFP and PM2.5 concentrations were monitored concurrently inside and outside of 22 taxis under different ventilation and mitigation conditions. Under realistic working conditions (no mitigation; NM), the average UFP and PM2.5 levels inside taxis were 1.46 × 104 particles/cm3 and 26 μg/m3, respectively. When the taxi ventilation was set to outside air mode and the windows kept closed, in-cabin UFP and PM2.5 concentrations are significantly associated with on-road concentrations, driving speed, and cabin air filter usage. The average in-cabin to on-roadway (I/O) ratios for UFP and PM2.5 were reduced from 0.60 to 0.75 under NM, to 0.47 and 0.52 under the most stringent mitigation strategy of keeping the windows closed and operating a high efficiency cabin air filter (WC + HECA). Among all tested taxi models, Toyota Prius exhibited the lowest UFP and PM2.5 I/O ratios under WC + HECA. Switching cabin air filters from the originally equipped manufacturer filter (OEM) to a HECA filter reduced the UFP and PM2.5 I/O ratios most effectively in Toyota Prius taxis as well.

Maternal and fetal outcomes after uterine fundal pressure in spontaneous and assisted vaginal deliveries.

PubMed

Furrer, Romana; Schäffer, Leonhard; Kimmich, Nina; Zimmermann, Roland; Haslinger, Christian

2016-10-01

This study aimed to evaluate maternal and fetal outcomes after uterine fundal pressure (UFP) in spontaneous and assisted vaginal deliveries. In a retrospective cohort study, 9743 singleton term deliveries with cephalic presentation were analyzed from 2004 to 2013. Spontaneous and assisted vaginal deliveries were analyzed separately with and without the application of UFP. Odds ratios were adjusted in a multivariate logistic regression analysis. Prevalence of UFP was 8.9% in spontaneous and 12.1% in assisted vaginal deliveries. UFP was associated with a higher incidence of shoulder dystocia in both spontaneous (adjusted odds ratio [adj. OR] 2.44, confidence interval [CI] 95% 1.23-4.84) and assisted vaginal deliveries (adj. OR 6.88 CI 95% 3.50-13.53). Fetal acidosis (arterial umbilical pH<7.2) was seen more often after the application of UFP in spontaneous vaginal deliveries (adj. OR 3.18, CI 95% 2.64-3.82) and assisted vaginal deliveries (adj. OR 1.59 CI 95% 1.17-2.16). The incidence of 5'-Apgar<7 (adj. OR 2.19 CI 95% 1.04-4.6) and 10'-Apgar<7 (adj. OR 3.04 CI 95% 1.17-7.88) was also increased after the application of UFP in spontaneous deliveries. A higher incidence of anal sphincter tears (AST) (adj. OR 46.25 CI 95% 11.78-181.6) in the UFP group of spontaneous deliveries was observed. UFP is associated with increased occurrence of shoulder dystocia and fetal acidosis. In spontaneous deliveries, the risk for lower Apgar scores after 5 and 10 min is increased, as well as the risk for AST.

Postharvest Ultrasound-Assisted Freeze-Thaw Pretreatment Improves the Drying Efficiency, Physicochemical Properties, and Macamide Biosynthesis of Maca (Lepidium meyenii).

PubMed

Chen, Jin-Jin; Gong, Peng-Fei; Liu, Yi-Lan; Liu, Bo-Yan; Eggert, Dawn; Guo, Yuan-Heng; Zhao, Ming-Xia; Zhao, Qing-Sheng; Zhao, Bing

2018-04-01

A novel technique of ultrasound-assisted freeze-thaw pretreatment (UFP) was developed to improve the drying efficiency of maca and bioactive amide synthesis in maca. The optimal UFP conditions are ultrasonic processing 90 min at 30 °C with 6 freeze-thaw cycles. Samples with freeze-thaw pretreatment (FP), ultrasound pretreatment (UP), and UFP were prepared for further comparative study. A no pretreatment (NP) sample was included as a control. The results showed that UFP improved the drying efficiency of maca slices, showing the highest effective moisture diffusivity (1.75 × 10 -9 m 2 /s). This result was further supported by low-field nuclear magnetic resonance (LF-NMR) analysis and scanning electron microscopy (SEM). The rehydration capacity and protein content of maca slices were improved by UFP. More importantly, contents of bioactive macamides and their biosynthetic precursors were increased in 2.5- and 10-fold, respectively. In conclusion, UFP is an efficient technique to improve drying efficiency, physicochemical properties, and bioactive macamides of maca, which can be applied in the industrial manufacture of maca products. © 2018 Institute of Food Technologists®.

Fingerprint of Lung Fluid Ultrafine Particles, a Novel Marker of Acute Lung Inflammation.

PubMed

Bar-Shai, Amir; Alcalay, Yifat; Sagiv, Adi; Rotem, Michal; Feigelson, Sara W; Alon, Ronen; Fireman, Elizabeth

2015-01-01

Acute lung inflammation can be monitored by various biochemical readouts of bronchoalveolar lavage fluid (BALF). To analyze the BALF content of ultrafine particles (UFP; <100 nm) as an inflammatory biomarker in early diagnosis of acute and chronic lung diseases. Mice were exposed to different stress conditions and inflammatory insults (acute lipopolysaccharide inhalation, tobacco smoke and lethal dose of total body irradiation, i.e. 950 rad). After centrifugation, the cellular pellet was assessed while cytokines and ultrafine particles were measured in the soluble fraction of the BALF. A characteristic UFP distribution with a D50 (i.e. the dimension of the 50th UFP percentile) was shared by all tested mouse strains in the BALF of resting lungs. All tested inflammatory insults similarly shifted this size distribution, resulting in a unique UFP fingerprint with an averaged D50 of 58.6 nm, compared with the mean UFP D50 of 23.7 nm for resting BALF (p < 0.0001). This UFP profile was highly reproducible and independent of the intensity or duration of the inflammatory trigger. It returned to baseline after resolution of the inflammation. Neither total body irradiation nor induction of acute cough induced this fingerprint. The UFP fingerprint in the BALF of resting and inflamed lungs can serve as a binary biomarker of healthy and acutely inflamed lungs. This marker can be used as a novel readout for the onset of inflammatory lung diseases and for complete lung recovery from different insults.

Ambient ultrafine particles provide a strong adjuvant effect in the secondary immune response: implication for traffic-related asthma flares

PubMed Central

Li, Ning; Harkema, Jack R.; Lewandowski, Ryan P.; Wang, Meiying; Bramble, Lori A.; Gookin, Glenn R.; Ning, Zhi; Kleinman, Michael T.; Sioutas, Constantinos

2010-01-01

We have previously demonstrated that intranasal administration of ambient ultrafine particles (UFP) acts as an adjuvant for primary allergic sensitization to ovalbumin (OVA) in Balb/c mice. It is important to find out whether inhaled UFP exert the same effect on the secondary immune response as a way of explaining asthma flares in already-sensitized individuals due to traffic exposure near a freeway. The objective of this study is to determine whether inhalation exposure to ambient UFP near an urban freeway could enhance the secondary immune response to OVA in already-sensitized mice. Prior OVA-sensitized animals were exposed to concentrated ambient UFP at the time of secondary OVA challenge in our mobile animal laboratory in Los Angeles. OVA-specific antibody production, airway morphometry, allergic airway inflammation, cytokine gene expression, and oxidative stress marker were assessed. As few as five ambient UFP exposures were sufficient to promote the OVA recall immune response, including generating allergic airway inflammation in smaller and more distal airways compared with the adjuvant effect of intranasally instilled UFP on the primary immune response. The secondary immune response was characterized by the T helper 2 and IL-17 cytokine gene expression in the lung. In summary, our results demonstrated that inhalation of prooxidative ambient UFP could effectively boost the secondary immune response to an experimental allergen, indicating that vehicular traffic exposure could exacerbate allergic inflammation in already-sensitized subjects. PMID:20562226

Particle number concentrations near the Rome-Ciampino city airport

NASA Astrophysics Data System (ADS)

Stafoggia, M.; Cattani, G.; Forastiere, F.; Di Menno di Bucchianico, A.; Gaeta, A.; Ancona, C.

2016-12-01

Human exposure to ultrafine particles (UFP) has been postulated to be associated with adverse health effects, and there is interest regarding possible measures to reduce primary emissions. One important source of UFP are airport activities, with aircraft take-offs being the most relevant one. We implemented two measurement campaigns of total particle number concentrations (PNC), a proxy for UFP, near a medium-size airport in central Italy. One-minute PNC averages were collected on June 2011 and January 2012 concurrently with 30-min average meteorological data on temperature and wind speed/direction. Data on minute-specific take-offs and landings were obtained by the airport authorities. We applied statistical regression models to relate PNC data to the presence of aircraft activities while adjusting for time trends and meteorology, and estimated the increases in PNC ±15 min before and after take-offs and landings. We repeated the analyses considering prevalent wind direction and by size of the aircraft. We estimated PNC increases of 5400 particles/cm3/minute during the 15 min before and after take-offs, with a peak of 19,000 particles/cm3/minute within 5 min after take-offs. Corresponding figures for landings were 1300 and 1000 particles, respectively. The highest PNC estimates were obtained when the prevailing wind came from the runway direction, and led to estimated PNC increases of 60,000 particles/cm3/minute within 5 min after take-offs. No main differences were noted from the exhaust of different types of aircrafts. The area surrounding Ciampino airport is densely inhabited, raising concerns about the potential adverse effects of long-term and short-term exposure to airport-borne UFP. A close monitoring of airport activities and emissions is mandatory to reduce the public health impact of the airport on the nearby population.

Determinants of spikes in ultrafine particle concentration whilst commuting by bus

NASA Astrophysics Data System (ADS)

Lim, Shanon; Dirks, Kim N.; Salmond, Jennifer A.; Xie, Shanju

2015-07-01

This paper examines concentration of ultrafine particles (UFPs) based on data collected using high-resolution UFP monitors whilst travelling by bus during rush hour along three different urban routes in Auckland, New Zealand. The factors influencing in-bus UFP concentration were assessed using a combination of spatial, statistical and GIS analysis techniques to determine both spatial and temporal variability. Results from 68 bus trips showed that concentrations varied more within a route than between on a given day, despite differences in urban morphology, land use and traffic densities between routes. A number of trips were characterised by periods of very rapid increases in UFPs (concentration 'spikes'), followed by slow declines. Trips which recorded at least one spike (an increase of greater than 10,000 pt/cm3) resulted in significantly higher mean concentrations. Spikes in UFPs were significantly more likely to occur when travelling at low speeds and when passengers were alighting and boarding at bus stops close to traffic light intersections.

Chemical, dimensional and morphological ultrafine particle characterization from a waste-to-energy plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buonanno, Giorgio, E-mail: buonanno@unicas.it; Stabile, Luca; Avino, Pasquale

2011-11-15

Highlights: > Particle size distributions and total concentrations measurement at the stack and before the fabric filter of an incinerator. > Chemical characterization of UFPs in terms of heavy metal concentration through a nuclear method. > Mineralogical investigation through a Transmission Electron Microscope equipped with an Energy Dispersive Spectrometer. > Heavy metal concentrations on UFPs as function of the boiling temperature. > Different mineralogical and morphological composition amongst samples collected before the fabric filter and at the stack. - Abstract: Waste combustion processes are responsible of particles and gaseous emissions. Referring to the particle emission, in the last years specificmore » attention was paid to ultrafine particles (UFPs, diameter less than 0.1 {mu}m), mainly emitted by combustion processes. In fact, recent findings of toxicological and epidemiological studies indicate that fine and ultrafine particles could represent a risk for health and environment. Therefore, it is necessary to quantify particle emissions from incinerators also to perform an exposure assessment for the human populations living in their surrounding areas. To these purposes, in the present work an experimental campaign aimed to monitor UFPs was carried out at the incineration plant in San Vittore del Lazio (Italy). Particle size distributions and total concentrations were measured both at the stack and before the fabric filter inlet in order to evaluate the removal efficiency of the filter in terms of UFPs. A chemical characterization of UFPs in terms of heavy metal concentration was performed through a nuclear method, i.e. Instrumental Neutron Activation Analysis (INAA), as well as a mineralogical investigation was carried out through a Transmission Electron Microscope (TEM) equipped with an Energy Dispersive Spectrometer (EDS) in order to evaluate shape, crystalline state and mineral compound of sampled particles. Maximum values of 2.7 x 10{sup 7} part. cm{sup -3} and 2.0 x 10{sup 3} part. cm{sup -3} were found, respectively, for number concentration before and after the fabric filter showing a very high efficiency in particle removing by the fabric filter. With regard to heavy metal concentrations, the elements with higher boiling temperature present higher concentrations at lower diameters showing a not complete evaporation in the combustion section and the consequent condensation of semi-volatile compounds on solid nuclei. In terms of mineralogical and morphological analysis, the most abundant compounds found in samples collected before the fabric filter are Na-K-Pb oxides followed by phyllosilicates, otherwise, different oxides of comparable abundance were detected in the samples collected at the stack.« less

Effect of cabin ventilation rate on ultrafine particle exposure inside automobiles.

PubMed

Knibbs, Luke D; de Dear, Richard J; Morawska, Lidia

2010-05-01

We alternately measured on-road and in-vehicle ultrafine (<100 nm) particle (UFP) concentration for 5 passenger vehicles that comprised an age range of 18 years. A range of cabin ventilation settings were assessed during 301 trips through a 4 km road tunnel in Sydney, Australia. Outdoor air flow (ventilation) rates under these settings were quantified on open roads using tracer gas techniques. Significant variability in tunnel trip average median in-cabin/on-road (I/O) UFP ratios was observed (0.08 to approximately 1.0). Based on data spanning all test automobiles and ventilation settings, a positive linear relationship was found between outdoor air flow rate and I/O ratio, with the former accounting for a substantial proportion of variation in the latter (R(2) = 0.81). UFP concentrations recorded in-cabin during tunnel travel were significantly higher than those reported by comparable studies performed on open roadways. A simple mathematical model afforded the ability to predict tunnel trip average in-cabin UFP concentrations with good accuracy. Our data indicate that under certain conditions, in-cabin UFP exposures incurred during tunnel travel may contribute significantly to daily exposure. The UFP exposure of automobile occupants appears strongly related to their choice of ventilation setting and vehicle.

Comparing the impact of ultrafine particles from petrodiesel and biodiesel combustion to bacterial metabolism by targeted HPLC-MS/MS metabolic profiling.

PubMed

Zhong, Fanyi; Xu, Mengyang; Schelli, Katie; Rutowski, Joshua; Holmén, Britt A; Zhu, Jiangjiang

2017-08-01

Alterations of gut bacterial metabolism play an important role in their host metabolism, and can result in diseases such as obesity and diabetes. While many factors were discovered influencing the gut bacterial metabolism, exposure to ultrafine particles (UFPs) from engine combustions were recently proposed to be a potential risk factor for the perturbation of gut bacterial metabolism, and consequentially to obesity and diabetes development. This study focused on evaluation of how UFPs from diesel engine combustions impact gut bacterial metabolism. We hypothesize that UFPs from different type of diesel (petrodiesel vs. biodiesel) will both impact bacterial metabolism, and the degree of impact is also diesel type-dependent. Targeted metabolic profiling of 221 metabolites were applied to three model gut bacteria in vitro, Streptococcus salivarius, Lactobacillus acidophilus and Lactobacillus fermentum. UFPs from two types of fuels, petrodiesel (B0) and a biodiesel blend (B20: 20% soy biodiesel/80% B0 by volume), were exposed to the bacteria and their metabolic changes were compared. For each bacterial strain, metabolites with significantly changed abundance were observed in both perturbations, and all three strains have increased number of altered metabolites detected from B20 UFPs perturbation in comparison to B0 UFPs. Multivariate statistical analysis further confirmed that the metabolic profiles were clearly different between testing groups. Metabolic pathway analyses also demonstrated several important metabolic pathways, including pathways involves amino acids biosynthesis and sugar metabolism, were significantly impacted by UFPs exposure. Copyright © 2017 Elsevier Inc. All rights reserved.

Reduction of exposure to ultrafine particles by kitchen exhaust hoods: the effects of exhaust flow rates, particle size, and burner position.

PubMed

Rim, Donghyun; Wallace, Lance; Nabinger, Steven; Persily, Andrew

2012-08-15

Cooking stoves, both gas and electric, are one of the strongest and most common sources of ultrafine particles (UFP) in homes. UFP have been shown to be associated with adverse health effects such as DNA damage and respiratory and cardiovascular diseases. This study investigates the effectiveness of kitchen exhaust hoods in reducing indoor levels of UFP emitted from a gas stove and oven. Measurements in an unoccupied manufactured house monitored size-resolved UFP (2 nm to 100 nm) concentrations from the gas stove and oven while varying range hood flow rate and burner position. The air change rate in the building was measured continuously based on the decay of a tracer gas (sulfur hexafluoride, SF(6)). The results show that range hood flow rate and burner position (front vs. rear) can have strong effects on the reduction of indoor levels of UFP released from the stove and oven, subsequently reducing occupant exposure to UFP. Higher range hood flow rates are generally more effective for UFP reduction, though the reduction varies with particle diameter. The influence of the range hood exhaust is larger for the back burner than for the front burner. The number-weighted particle reductions for range hood flow rates varying between 100 m(3)/h and 680 m(3)/h range from 31% to 94% for the front burner, from 54% to 98% for the back burner, and from 39% to 96% for the oven. Copyright © 2012 Elsevier B.V. All rights reserved.

Occupational exposure to ultrafine particles in police officers: no evidence for adverse respiratory effects.

PubMed

Jordakieva, G; Grabovac, I; Valic, E; Schmidt, K E; Graff, A; Schuster, A; Hoffmann-Sommergruber, K; Oberhuber, C; Scheiner, O; Goll, A; Godnic-Cvar, J

2018-01-01

Inhalation exposure to fine and ultrafine particles (UFPs) has been associated with respiratory diseases. However, little is known on the quality, threshold levels and concentration of these particles causing adverse health effects. The impact of occupational exposure to submicrometer and UFPs was assessed in 30 healthy police shooting instructors by clinical investigation, self-assessment questionnaire, sputum and spirometry and compared to a control group. General laboratory chemistry parameters, circulating cytokines (interleukin [IL]-2, IL-4, IL-5, IL-6, IL-8, interferon-gamma [IFN-γ]), and granulocyte macrophage colony-stimulating factor (GM-CSF) in serum were measured. UFP exposure was recorded by Scanning Mobility Particle Sizer. Concentrations of submicrometer sized airborne particles (< 700 nm) measured between 3.34 × 10 5 /cm 3 and 7.58 × 10 5 /cm 3 at shooting sites, with highest concentrations found in the UFP range (< 100 nm). The size of the monodispersed particles ranged from 54.74 ± 16.25 nm to 98.19 ± 22.83 nm. Short term exposure (4 h) to high levels of UFPs caused an increase of IFN-γ in exposed subjects ( p  = 0.022). 24 h after exposure a significant decrease of IgG, albumin fibrinogen and factor VII was found. Neither directly after 4 h of high levels UFPs exposure nor 24 h after exposure subjective complaints or objective measurements indicating adverse respiratory effects in exposed subjects were found. No consistent indications for adverse respiratory or inflammatory effects directly following exposure and 24 h after exposure to high levels of UFPs in our study group were detected. However we showed the assessment of short-term exposure effects at a genuine occupational setting, which might is relevant when a risk assessment of high level occupational exposures to UFPs is considered.

The effect of image force and diffusion on the deposition of ultrafine particle to vegetation

NASA Astrophysics Data System (ADS)

Lin, M. Y.; Katul, G. G.; Huang, C. W.; CHU, C. R.; Khlystov, A.

2017-12-01

Ultrafine particles (UFP) along with their sources and sinks are gaining significant attention due to their dual role in cloud microphysics and human health. Due to its expansive areal extent, vegetation is a significant sink for UFP thus prompting interest in how UFP deposit onto vegetated surfaces. Single fiber theory reasonably explains deposition of zero charge UFP onto vegetation by treating vegetation as filter media. However, the ability of the single fiber theory to predict deposition of charged UFP onto vegetation remains unknown and frames the scope of this presentation. Wind tunnel experiments are used to investigate UFP deposition (size range 12.6 - 102 nm) onto Juniper branches (Juniperus chinesis) and their results are interpreted using single fiber theory. Three different wind speeds (0.3, 0.6, and 0.9 m/s) are investigated to study deposition of singly-charged particles and these deposition values are contrasted with neutrally charged particles. The wind tunnel experiments indicate that single fiber theory can be used to describe deposition of singly-charged particles onto vegetation if both the image force and Brownian diffusion are simultaneously considered. The image force was found to be proportional to KIM0.5 when the image force dimensionless number (KIM) is smaller than 10-8, a common condition for singly charged UFP particle. The proportionality constant was found to be 27.6 (i.e. 27.6×KIM0.5) and is larger than a previously reported value (9.7) derived for KIM between 10-7 10-5, primarily due to the lower KIM (<10-8) in this study. Another study also showed that this proportionality constant increases with decreasing KIM. With this representation for the image force, the single fiber filtration model and measurements agree to within 20%. The work here offers a new perspective on the role of image force at small KIM (10-10 10-8) and its role in enhanced deposition of charged UFP onto vegetation.

Personal exposure to ultrafine particles.

PubMed

Wallace, Lance; Ott, Wayne

2011-01-01

Personal exposure to ultrafine particles (UFP) can occur while people are cooking, driving, smoking, operating small appliances such as hair dryers, or eating out in restaurants. These exposures can often be higher than outdoor concentrations. For 3 years, portable monitors were employed in homes, cars, and restaurants. More than 300 measurement periods in several homes were documented, along with 25 h of driving two cars, and 22 visits to restaurants. Cooking on gas or electric stoves and electric toaster ovens was a major source of UFP, with peak personal exposures often exceeding 100,000 particles/cm³ and estimated emission rates in the neighborhood of 10¹² particles/min. Other common sources of high UFP exposures were cigarettes, a vented gas clothes dryer, an air popcorn popper, candles, an electric mixer, a toaster, a hair dryer, a curling iron, and a steam iron. Relatively low indoor UFP emissions were noted for a fireplace, several space heaters, and a laser printer. Driving resulted in moderate exposures averaging about 30,000 particles/cm³ in each of two cars driven on 17 trips on major highways on the East and West Coasts. Most of the restaurants visited maintained consistently high levels of 50,000-200,000 particles/cm³ for the entire length of the meal. The indoor/outdoor ratios of size-resolved UFP were much lower than for PM₂.₅ or PM₁₀, suggesting that outdoor UFP have difficulty in penetrating a home. This in turn implies that outdoor concentrations of UFP have only a moderate effect on personal exposures if indoor sources are present. A time-weighted scenario suggests that for typical suburban nonsmoker lifestyles, indoor sources provide about 47% and outdoor sources about 36% of total daily UFP exposure and in-vehicle exposures add the remainder (17%). However, the effect of one smoker in the home results in an overwhelming increase in the importance of indoor sources (77% of the total).

Air pollution ultrafine particles: toxicity beyond the lung.

PubMed

Terzano, C; Di Stefano, F; Conti, V; Graziani, E; Petroianni, A

2010-10-01

Ultrafine particles or nanoparticles (UFPs or PM0.1) are the fraction of ambient particulates with an aerodynamic diameter smaller than 0.1 microm. Currently UFPs are emerging as the most abundant particulate pollutants in urban and industrial areas, as their exposures have increased dramatically because of anthropogenic sources such as internal combustion engines, power plants, incinerators and many other sources of thermo-degradation. Ultrafine particles have been less studied than PM2.5 and PM10 particulates, mass concentrations of particles smaller than 2.5 and 10 microm, respectively. OBJECTIVE, EVIDENCE AND INFORMATION SOURCES: We examined the current scientific literature about the health effects of ultrafine particles exposure. UFPs are able to inhibit phagocytosis, and to stimulate inflammatory responses, damaging epithelial cells and potentially gaining access to the interstitium. They could be responsible for consistent reductions in forced expiratory volume in 1 second (FEV1) and forced vital capacity (FVC) in patients with asthma. Chronic exposure to UFPs can produce deleterious effects on the lung, also causing oxidative stress and enhancing pro-inflammatory effects in airways of COPD patients. Cardiovascular detrimental consequences due to UFPs exposure have observed in epidemiological studies, and could likely be explained by translocation of UFPs from the respiratory epithelium towards circulation and subsequent toxicity to vascular endothelium; alteration of blood coagulation; triggering of autonomic nervous system reflexes eventually altering the cardiac frequency and function. Once deposited deeply into the lung, UFPs--in contrast to larger-sized particles--appear to access to the blood circulation by different transfer routes and mechanisms, resulting in distribution throughout the body, including the brain, with potential neurotoxic consequences. UFPs represent an area of toxicology of emerging concern. A new concept of environmental medicine would help in understanding not only the environmental mechanisms of disease, but also in developing specific preventive or therapeutic strategies for minimizing the dangerous influence of pollution on health.

Measurement of Ultrafine Particles and Other Air Pollutants Emitted by Cooking Activities

PubMed Central

Zhang, Qunfang; Gangupomu, Roja H.; Ramirez, David; Zhu, Yifang

2010-01-01

Cooking emissions show a strong dependence on cooking styles and parameters. Measurements of the average ultrafine particle (UFP) concentration, PM2.5 and black carbon concentrations emitted by cooking activities ranged from 1.34 × 104 to 6.04 × 105 particles/cm3, 10.0 to 230.9 μg/m3 and 0.1 to 0.8 μg/m3, respectively. Lower UFP concentrations were observed during boiling, while higher levels were emitted during frying. The highest UFP concentrations were observed when using a gas stove at high temperature with the kitchen exhaust fan turned off. The observed UFP profiles were similar in the kitchen and in another room, with a lag of approximately 10 min. PMID:20617057

Effect of Exposure to Atmospheric Ultrafine Particles on Production of Free Fatty Acids and Lipid Metabolites in the Mouse Small Intestine

PubMed Central

Li, Rongsong; Navab, Kaveh; Hough, Greg; Daher, Nancy; Zhang, Min; Mittelstein, David; Lee, Katherine; Pakbin, Payam; Saffari, Arian; Bhetraratana, May; Sulaiman, Dawoud; Beebe, Tyler; Wu, Lan; Jen, Nelson; Wine, Eytan; Tseng, Chi-Hong; Araujo, Jesus A.; Fogelman, Alan; Sioutas, Constantinos; Navab, Mohamed

2014-01-01

Background: Exposure to ambient ultrafine particulate matter (UFP) is a well-recognized risk factor for cardiovascular and respiratory diseases. However, little is known about the effects of air pollution on gastrointestinal disorders. Objective: We sought to assess whether exposure to ambient UFP (diameter < 180 nm) increased free fatty acids and lipid metabolites in the mouse small intestine. Methods: Ldlr-null mice were exposed to filtered air (FA) or UFP collected at an urban Los Angeles, California, site that was heavily affected by vehicular emissions; the exposure was carried out for 10 weeks in the presence or absence of D-4F, an apolipoprotein A-I mimetic peptide with antioxidant and anti-inflammation properties on a high-fat or normal chow diet. Results: Compared with FA, exposure to UFP significantly increased intestinal hydroxyeicosatetraenoic acids (HETEs), including 15-HETE, 12-HETE, 5-HETE, as well as hydroxyoctadecadienoic acids (HODEs), including 13-HODE and 9-HODE. Arachidonic acid (AA) and prostaglandin D2 (PGD2) as well as some of the lysophosphatidic acids (LPA) in the small intestine were also increased in response to UFP exposure. Administration of D-4F significantly reduced UFP-mediated increase in HETEs, HODEs, AA, PGD2, and LPA. Although exposure to UFP further led to shortened villus length accompanied by prominent macrophage and neutrophil infiltration into the intestinal villi, administration of D-4F mitigated macrophage infiltration. Conclusions: Exposure to UFP promotes lipid metabolism, villus shortening, and inflammatory responses in mouse small intestine, whereas administration of D-4F attenuated these effects. Our findings provide a basis to further assess the mechanisms underlying UFP-mediated lipid metabolism in the digestive system with clinical relevance to gut homeostasis and diseases. Citation: Li R, Navab K, Hough G, Daher N, Zhang M, Mittelstein D, Lee K, Pakbin P, Saffari A, Bhetraratana M, Sulaiman D, Beebe T, Wu L, Jen N, Wine E, Tseng CH, Araujo JA, Fogelman A, Sioutas C, Navab M, Hsiai TK. 2015. Effect of exposure to atmospheric ultrafine particles on production of free fatty acids and lipid metabolites in the mouse small intestine. Environ Health Perspect 123:34–41; http://dx.doi.org/10.1289/ehp.1307036 PMID:25170928

Differential pattern of deposition of nanoparticles in the airways of exposed workers

NASA Astrophysics Data System (ADS)

Fireman, Elizabeth; Edelheit, Rinat; Stark, Moshe; Shai, Amir Bar

2017-02-01

Ultrafine particles (UFP) have been postulated to significantly contribute to the adverse health effects associated with exposure to particulate matter (PM). Due to their extremely small size (aerodynamic diameter <100 nm), UFP are able to deposit deep within the lung after inhalation and evade many mechanisms responsible for the clearance of larger particles. There is a lack of biologically relevant personal exposure metrics for exposure to occupational- and environmental-related micro- and nano-sized PM. The aim of the present study is to assess UFP in induced sputum (IS) and exhaled breath condensate (EBC) as possible biomarkers for assessing lung function impairment. Sputum induction and EBC testing were performed by conventional methods. UFP particles were assessed with the NanoSight LM20 (NanoSight Ltd, London, UK). The subjects included 35 exposed and 25 non-exposed workers. There were no group differences in pulmonary function test results and differential cell counts, but 63.6% of the exposed subjects had a higher percentage of neutrophils (OR3.28 p = 0.03) compared to the non-exposed subjects. The exposed subjects had higher percentages of UFP between 10 and 50 nm (69.45 ± 18.70 vs 60.11 ± 17.52 for the non-exposed group, p = 0.004). No differences were found in the IS samples. Years of exposure correlated positively to UFP content ( r = 0.342 p = 0.01) and macrophage content ( r = -0.327 p = 0.03). The percentage of small fraction of UFP in EBC, but not IS, is higher in exposed workers, and EBC may be a sensitive biomarker to assess exposure to nanoparticles.

Workplace exposure and release of ultrafine particles during atmospheric plasma spraying in the ceramic industry.

PubMed

Viana, M; Fonseca, A S; Querol, X; López-Lilao, A; Carpio, P; Salmatonidis, A; Monfort, E

2017-12-01

Atmospheric plasma spraying (APS) is a frequently used technique to produce enhanced-property coatings for different materials in the ceramic industry. This work aimed to characterise and quantify the impact of APS on workplace exposure to airborne particles, with a focus on ultrafine particles (UFPs, <100nm) and nanoparticles (<50nm). Particle number, mass concentrations, alveolar lung deposited surface area concentration, and size distributions, in the range 10nm-20μm were simultaneously monitored at the emission source, in the potential worker breathing zone, and in outdoor air. Different input materials (known as feedstock) were tested: (a) micron-sized powders, and (b) suspensions containing submicron- or nano-sized particles. Results evidenced significantly high UFP concentrations (up to 3.3×10 6 /cm 3 ) inside the spraying chamber, which impacted exposure concentrations in the worker area outside the spraying chamber (up to 8.3×10 5 /cm 3 ). Environmental release of UFPs was also detected (3.9×10 5 /cm 3 , outside the exhaust tube). Engineered nanoparticle (ENP) release to workplace air was also evidenced by TEM microscopy. UFP emissions were detected during the application of both micron-sized powder and suspensions containing submicron- or nano-sized particles, thus suggesting that emissions were process- (and not material-) dependent. An effective risk prevention protocol was implemented, which resulted in a reduction of UFP exposure in the worker area. These findings demonstrate the potential risk of occupational exposure to UFPs during atmospheric plasma spraying, and raise the need for further research on UFP formation mechanisms in high-energy industrial processes. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Effects of exposure to ambient ultrafine particles on respiratory health and systemic inflammation in children.

PubMed

Clifford, Sam; Mazaheri, Mandana; Salimi, Farhad; Ezz, Wafaa Nabil; Yeganeh, Bijan; Low-Choy, Samantha; Walker, Katy; Mengersen, Kerrie; Marks, Guy B; Morawska, Lidia

2018-05-01

It is known that ultrafine particles (UFP, particles smaller than 0.1 μm) can penetrate deep into the lungs and potentially have adverse health effects. However, epidemiological data on the health effects of UFP is limited. Therefore, our objective was to test the hypothesis that exposure to UFPs is associated with respiratory health status and systemic inflammation among children aged 8 to 11 years. We conducted a cross-sectional study among 655 children (43.3% male) attending 25 primary (elementary) schools in the Brisbane Metropolitan Area, Australia. Ultrafine particle number concentration (PNC) was measured at each school and modelled at homes using Land Use Regression to derive exposure estimates. Health outcomes were respiratory symptoms and diagnoses, measured by parent-completed questionnaire, spirometric lung function, exhaled nitric oxide (FeNO), and serum C reactive protein (CRP). Exposure-response models, adjusted for potential personal and environmental confounders measured at the individual, home and school level, were fitted using Bayesian methods. PNC was not independently associated with respiratory symptoms, asthma diagnosis or spirometric lung function. However, PNC was positively associated with an increase in CRP (1.188-fold change per 1000 UFP cm -3 day/day (95% credible interval 1.077 to 1.299)) and an increase in FeNO among atopic participants (1.054 fold change per 1000 UFP cm -3 day/day (95% CrI 1.005 to 1.106)). UFPs do not affect respiratory health outcomes in children but do have systemic effects, detected here in the form of a positive association with a biomarker for systemic inflammation. This is consistent with the known propensity of UFPs to penetrate deep into the lung and circulatory system. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ultrafine particle exposures while walking, cycling, and driving along an urban residential roadway

NASA Astrophysics Data System (ADS)

Quiros, David C.; Lee, Eon S.; Wang, Rui; Zhu, Yifang

2013-07-01

Elevated concentrations of ultrafine particles (UFPs, <0.1 μm), which have been linked to adverse health effects, are commonly found along roadways. This study reports UFP and PM2.5 concentrations and respiratory exposures among four transportation modes on an urban residential street in Santa Monica, California while walking, cycling, and driving with windows open and windows closed (with air recirculation on). Repeated measurements were made for nine days during morning (7:30-9:30), afternoon (12:30-14:30), and evening (17:00-19:00) periods. Median UFP concentrations ranged 1-3 × 104 particles cm-3, were 70% lower in afternoon or evening periods compared to the morning, and were 60% lower when driving with windows closed than open. Median PM2.5 ranged 2-15 μg m-3, well below the annual National Ambient Air Quality standard of 15 μg m-3. Respiratory UFP exposure (particles inhaled trip-1) was ˜2 times higher while driving with windows open, ˜15 times higher when cycling, and ˜30 times higher walking, than driving with windows closed. During one evening session with perpendicular rather than parallel wind conditions, absolute UFP concentration was 80% higher, suggesting influence of off-roadway sources. Under parallel wind conditions, a parameter called emissions-weighted traffic volume, used to account for higher and lower emitting vehicles, was correlated with beach-site-subtracted UFP using second-order polynomial model (R2 = 0.61). Based on this model, an 83% on-roadway UFP reduction could be achieved by (1) requiring all trucks to meet California 2007 model-year engine standards, (2) reducing light-duty vehicle flows by 25%, and (3) replacing high-emitting light-duty vehicles (pre 1978) with newer 2010 fleet-average vehicles.

The effects of leaf size and microroughness on the branch-scale collection efficiency of ultrafine particles

DOE PAGES

Huang, C. W.; Lin, M. Y.; Khlystov, A.; ...

2015-03-02

In this study, wind tunnel experiments were performed to explore how leaf size and leaf microroughness impact the collection efficiency of ultrafine particles (UFP) at the branch scale. A porous media model previously used to characterize UFP deposition onto conifers (Pinus taeda and Juniperus chinensis) was employed to interpret these wind tunnel measurements for four different broadleaf species (Ilex cornuta, Quercus alba, Magnolia grandiflora, and Lonicera fragrantissima) and three wind speed (0.3–0.9 ms -1) conditions. Among the four broadleaf species considered, Ilex cornuta with its partially folded shape and sharp edges was the most efficient at collecting UFP followed bymore » the other three flat-shaped broadleaf species. The findings here suggest that a connection must exist between UFP collection and leaf dimension and roughness. This connection is shown to be primarily due to the thickness of a quasi-laminar boundary layer pinned to the leaf surface assuming the flow over a leaf resembles that of a flat plate. A scaling analysis that utilizes a three-sublayer depositional model for a flat plate of finite size and roughness embedded within the quasi-laminar boundary layer illustrates these connections. The analysis shows that a longer leaf dimension allows for thicker quasi-laminar boundary layers to develop. A thicker quasi-laminar boundary layer depth in turn increases the overall resistance to UFP deposition due to an increase in the diffusional path length thereby reducing the leaf-scale UFP collection efficiency. Finally, it is suggested that the effects of leaf microroughness are less relevant to the UFP collection efficiency than are the leaf dimensions for the four broadleaf species explored here.« less

The effects of blocking N/OFQ receptors on orofacial pain following experimental tooth movement in rats.

PubMed

Shan, Di; He, Yuwei; Long, Hu; Zhou, Yang; Liu, He; Xu, Rui; Huang, Renhuan; Lai, Wenli

2016-11-01

The aim of this study was to determine the effects of nociceptin/orphanin FQ peptide receptor (N/OFQ receptor) antagonist on orofacial pain induced by experimental tooth movement in rats. A total of 36 male Sprague-Dawley rats weighing 200-300 g were divided into six groups: a control group, force group, force+saline intraperitoneal group, force+saline periodontal group, force+UFP-101 ([Nphe¹,Arg¹⁴,Lys¹⁵]N/OFQ-NH ₂ antagonist for N/OFQ receptor) intraperitoneal group, and force+UFP-1 01 periodontal group. Closed coil springs were ligated between the upper incisors and first molar to exert an orthodontic force (40 g) between the teeth. Injectable administration dosages were 30 μl saline or 30 μl saline containing 0.03 mg/kg UFP-1 01. Following the injections, orofacial pain levels were assessed through directed face grooming (mouth wiping). Statistical analyses were performed in SPSS 17.0 (Statistical Package for the Social Sciences) and p values less than 0.05 were considered as statistically significant. Orofacial pain levels were significantly higher in the force group than in the control group. Orofacial pain levels differed significantly between the force)group, force+saline periodontal group and force+UFP-101 periodontal group, but were similar between the control group, force+UFP-101 intraperitoneal group and force+saline intraperitoneal group. Moreover, orofacial pain levels did not differ between the force group, force+saline intraperitoneal group and force+UFP-1 01 intraperitoneal group. Periodontal, but not intraperitoneal, administration of UFP-101 could alleviate orofacial pain induced by experimental tooth movement in rats, suggesting that periodontal N/OFQ receptors participate in orofacial pain induced by experimental tooth movement.

The impact of undergraduate clinical teaching models on the perceptions of work-readiness among new graduate nurses: A cross sectional study.

PubMed

Patterson, Emma E B; Boyd, Leanne; Mnatzaganian, George

2017-08-01

Clinical Placements are an essential component of bridging the gap between academic theory and nursing practice. There are multiple clinical models designed to ease the transition from student to professional, yet there has been little exploration of such models and their impact on graduates' perceptions of work-readiness. This cross sectional study examined perceptions of work-readiness of new graduate nurses who attended one of the following clinical teaching models: the University Fellowship Program (UFP), the Traditional Multi-facility Clinical Model (TMCPM), and the Mixed Program (MP). Three groups of first year graduate nurses (UFP, TMCPM, and MP) were compared using the Work-readiness Scale, a validated and reliable tool, which assessed nurses' perceptions of work-readiness in four domains: organizational acumen, personal work characteristics, social intelligence, and work competence. A multivariable Generalized Estimating Equations regression investigated socio-demographic and teaching-modelrelated factors associated with work-readiness. Of 43 nurses approached, 28 completed the survey (65% response rate) of whom 6 were UFP attendants, 8 attended the TMCPM and 14 the MP. Those who had attended the UFP scored higher than the other two in all four domains; however, the crude between-group comparisons did not yield statistically significant results. Only after accounting for age, gender, teaching setting and prior work experience, the multivariable model showed that undertaking the UFP was likely to increase perceptions of work-readiness by 1.4 points (95% CI 0.11-2.69), P=0.03). The UFP was superior to the other two placement models. The study suggests that the UFP may enhance graduate nurses' perceptions of work readiness. Copyright © 2017 Elsevier Ltd. All rights reserved.

Translocation of Inhaled Ultrafine Manganese Oxide Particles to the Central Nervous System

PubMed Central

Elder, Alison; Gelein, Robert; Silva, Vanessa; Feikert, Tessa; Opanashuk, Lisa; Carter, Janet; Potter, Russell; Maynard, Andrew; Ito, Yasuo; Finkelstein, Jacob; Oberdörster, Günter

2006-01-01

Background Studies in monkeys with intranasally instilled gold ultrafine particles (UFPs; < 100 nm) and in rats with inhaled carbon UFPs suggested that solid UFPs deposited in the nose travel along the olfactory nerve to the olfactory bulb. Methods To determine if olfactory translocation occurs for other solid metal UFPs and assess potential health effects, we exposed groups of rats to manganese (Mn) oxide UFPs (30 nm; ~ 500 μg/m3) with either both nostrils patent or the right nostril occluded. We analyzed Mn in lung, liver, olfactory bulb, and other brain regions, and we performed gene and protein analyses. Results After 12 days of exposure with both nostrils patent, Mn concentrations in the olfactory bulb increased 3.5-fold, whereas lung Mn concentrations doubled; there were also increases in striatum, frontal cortex, and cerebellum. Lung lavage analysis showed no indications of lung inflammation, whereas increases in olfactory bulb tumor necrosis factor-α mRNA (~ 8-fold) and protein (~ 30-fold) were found after 11 days of exposure and, to a lesser degree, in other brain regions with increased Mn levels. Macrophage inflammatory protein-2, glial fibrillary acidic protein, and neuronal cell adhesion molecule mRNA were also increased in olfactory bulb. With the right nostril occluded for a 2-day exposure, Mn accumulated only in the left olfactory bulb. Solubilization of the Mn oxide UFPs was < 1.5% per day. Conclusions We conclude that the olfactory neuronal pathway is efficient for translocating inhaled Mn oxide as solid UFPs to the central nervous system and that this can result in inflammatory changes. We suggest that despite differences between human and rodent olfactory systems, this pathway is relevant in humans. PMID:16882521

The effects of leaf size and microroughness on the branch-scale collection efficiency of ultrafine particles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, C. W.; Lin, M. Y.; Khlystov, A.

In this study, wind tunnel experiments were performed to explore how leaf size and leaf microroughness impact the collection efficiency of ultrafine particles (UFP) at the branch scale. A porous media model previously used to characterize UFP deposition onto conifers (Pinus taeda and Juniperus chinensis) was employed to interpret these wind tunnel measurements for four different broadleaf species (Ilex cornuta, Quercus alba, Magnolia grandiflora, and Lonicera fragrantissima) and three wind speed (0.3–0.9 ms -1) conditions. Among the four broadleaf species considered, Ilex cornuta with its partially folded shape and sharp edges was the most efficient at collecting UFP followed bymore » the other three flat-shaped broadleaf species. The findings here suggest that a connection must exist between UFP collection and leaf dimension and roughness. This connection is shown to be primarily due to the thickness of a quasi-laminar boundary layer pinned to the leaf surface assuming the flow over a leaf resembles that of a flat plate. A scaling analysis that utilizes a three-sublayer depositional model for a flat plate of finite size and roughness embedded within the quasi-laminar boundary layer illustrates these connections. The analysis shows that a longer leaf dimension allows for thicker quasi-laminar boundary layers to develop. A thicker quasi-laminar boundary layer depth in turn increases the overall resistance to UFP deposition due to an increase in the diffusional path length thereby reducing the leaf-scale UFP collection efficiency. Finally, it is suggested that the effects of leaf microroughness are less relevant to the UFP collection efficiency than are the leaf dimensions for the four broadleaf species explored here.« less

A Jagged 1-Notch 4 molecular switch mediates airway inflammation induced by ultrafine particles.

PubMed

Xia, Mingcan; Harb, Hani; Saffari, Arian; Sioutas, Constantinos; Chatila, Talal A

2018-04-05

Exposure to traffic-related particulate matter promotes asthma and allergic diseases. However, the precise cellular and molecular mechanisms by which particulate matter exposure acts to mediate these effects remain unclear. We sought to elucidate the cellular targets and signaling pathways critical for augmentation of allergic airway inflammation induced by ambient ultrafine particles (UFP). We used in vitro cell-culture assays with lung-derived antigen-presenting cells and allergen-specific T cells and in vivo mouse models of allergic airway inflammation with myeloid lineage-specific gene deletions, cellular reconstitution approaches, and antibody inhibition studies. We identified lung alveolar macrophages (AM) as the key cellular target of UFP in promoting airway inflammation. Aryl hydrocarbon receptor-dependent induction of Jagged 1 (Jag1) expression in AM was necessary and sufficient for augmentation of allergic airway inflammation by UFP. UFP promoted T H 2 and T H 17 cell differentiation of allergen-specific T cells in a Jag1- and Notch 4-dependent manner. Treatment of mice with an anti-Notch 4 antibody abrogated exacerbation of allergic airway inflammation induced by UFP. UFP exacerbate allergic airway inflammation by promoting a Jag1-Notch 4-dependent interaction between AM and allergen-specific T cells, leading to augmented T H cell differentiation. Copyright © 2018 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

Measurements of ultrafine particles carrying different number of charges in on- and near-freeway environments

NASA Astrophysics Data System (ADS)

Lee, Eon S.; Xu, Bin; Zhu, Yifang

2012-12-01

This paper presents measurements of electrical charges on ultrafine particles (UFPs) of different electrical mobility diameters (30, 50, 80, and 100 nm) in on- and near-freeway environments. Using a tandem Differential Mobility Analyzer (DMA) system, we first examined the fraction of UFPs carrying different number of charges on two distinctive freeways: a gasoline-vehicle dominated freeway (I-405) and a heavy-duty diesel truck dominated freeway (I-710). The fractions of UFPs of a given size carrying one or more charges were significantly higher on the freeways than in the background. The background UFPs only carried up to two charges but freeway UFPs could have up to three charges. The total fraction of charged particles was higher on the I-710 than I-405 across the studied electrical mobility diameters. Near the I-405 freeway, we observed a strong decay of charged particles on the downwind side of the freeway. We also found fractional decay of the charged particles was faster than total particle number concentrations, but slower than total ion concentrations downwind from the freeway I-405. Among charged particles, the highest decay rate was observed for particles carrying three charges. Near the I-710 freeway, we found strong net positive charges on nucleation mode particles, suggesting that UFPs were not at steady-state charge equilibrium near freeways.

Observation of Elevated Air Pollutant Concentrations in a Residential Neighborhood of Los Angeles California Using a Mobile Platform

PubMed Central

Hu, Shishan; Fruin, Scott; Kozawa, Kathleen; Mara, Steve; Winer, Arthur M.

2013-01-01

We observed elevated air pollutant concentrations, especially of ultrafine particles (UFP), black carbon (BC) and NO, across the residential neighborhood of the Boyle Heights Community (BH) of Los Angeles, California. Using an electric vehicle mobile platform equipped with fast response instruments, real-time air pollutant concentrations were measured in BH in spring and summer of 2008. Pollutant concentrations varied significantly in the two seasons, on different days, and by time of day, with an overall average UFP concentration in the residential areas of ~33 000 cm−3. The averaged UFP, BC, and NO concentrations measured on Soto St, a major surface street in BH, were 57 000 cm−3, 5.1 µg m−3, and 67 ppb, respectively. Concentrations of UFP across the residential areas in BH were nearly uniform spatially, in contrast to other areas in the greater metropolitan area of Los Angeles where UFP concentrations exhibit strong gradients downwind of roadways. We attribute this “UFP cloud” to high traffic volumes, including heavy duty diesel trucks on the freeways which surround and traverse BH, and substantial numbers of high-emitting vehicles (HEVs) on the surface streets traversing BH. Additionally, the high density of stop signs and lights and short block lengths, requiring frequent accelerations of vehicles, may contribute. The data also support a role for photochemical production of UFP in the afternoon. UFP concentration peaks (5 s average) of up to 9 million particles cm−3 were also observed immediately behind HEVs when they accelerated from stop lights in the BH neighborhood and areas immediately adjacent. Although encounters with HEV during mornings accounted for only about 6% and 17% of time spent monitoring residential areas and major surface streets, HEV contributed to about 28% and 53% of total ultrafine particles measured on the route, respectively. The observation of elevated pollutant number concentrations across the Boyle Heights community highlights how multiple factors combine to create high pollutant levels, and has important human exposure assessment implications, including the potential utility of our data as inputs to epidemiological studies. PMID:23997642

Aircraft emission impacts in a neighborhood adjacent to a general aviation airport in southern California.

PubMed

Hu, Shishan; Fruin, Scott; Kozawa, Kathleen; Mara, Steve; Winer, Arthur M; Paulson, Suzanne E

2009-11-01

Real time air pollutant concentrations were measured downwind of Santa Monica Airport (SMA), using an electric vehicle mobile platform equipped with fast response instruments in spring and summer of 2008. SMA is a general aviation airport operated for private aircraft and corporate jets in Los Angeles County, California. An impact area of elevated ultrafine particle (UFP) concentrations was observed extending beyond 660 m downwind and 250 m perpendicular to the wind on the downwind side of SMA. Aircraft operations resulted in average UFP concentrations elevated by factors of 10 and 2.5 at 100 and 660 m downwind, respectively, over background levels. The long downwind impact distance (i.e., compared to nearby freeways at the same time of day) is likely primarily due to the large volumes of aircraft emissions containing higher initial concentrations of UFP than on-road vehicles. Aircraft did not appreciably elevate average levels of black carbon (BC), particle-bound polycyclic aromatic hydrocarbons (PB-PAH), although spikes in concentration of these pollutants were observed associated with jet takeoffs. Jet departures resulted in peak 60-s average concentrations of up to 2.2 x 10(6) cm(-3), 440 ng m(-3), and 30 microg m(-3) for UFP, PB-PAH, and BC, respectively, 100 m downwind of the takeoff area. These peak levels were elevated by factors of 440, 90, and 100 compared to background concentrations. Peak UFP concentrations were reasonably correlated (r(2) = 0.62) with fuel consumption rates associated with aircraft departures, estimated from aircraft weights and acceleration rates. UFP concentrations remained elevated for extended periods associated particularly with jet departures, but also with jet taxi and idle, and operations of propeller aircraft. UFP measured downwind of SMA had a median mode of about 11 nm (electric mobility diameter), which was about half of the 22 nm median mode associated with UFP from heavy duty diesel trucks. The observation of highly elevated ultrafine particle concentrations in a large residential area downwind of this local airport has potential health implications for persons living near general aviation airports.

Observation of elevated air pollutant concentrations in a residential neighborhood of Los Angeles California using a mobile platform

NASA Astrophysics Data System (ADS)

Hu, Shishan; Paulson, Suzanne E.; Fruin, Scott; Kozawa, Kathleen; Mara, Steve; Winer, Arthur M.

2012-05-01

We observed elevated air pollutant concentrations, especially of ultrafine particles (UFP), black carbon (BC) and NO, across the residential neighborhood of the Boyle Heights Community (BH) of Los Angeles, California. Using an electric vehicle mobile platform equipped with fast response instruments, real-time air pollutant concentrations were measured in BH in spring and summer of 2008. Pollutant concentrations varied significantly in the two seasons, on different days, and by time of day, with an overall average UFP concentration in the residential areas of ∼33 000 cm-3. The averaged UFP, BC, and NO concentrations measured on Soto St, a major surface street in BH, were 57 000 cm-3, 5.1 μg m-3, and 67 ppb, respectively. Concentrations of UFP across the residential areas in BH were nearly uniform spatially, in contrast to other areas in the greater metropolitan area of Los Angeles where UFP concentrations exhibit strong gradients downwind of roadways. We attribute this “UFP cloud” to high traffic volumes, including heavy duty diesel trucks on the freeways which surround and traverse BH, and substantial numbers of high-emitting vehicles (HEVs) on the surface streets traversing BH. Additionally, the high density of stop signs and lights and short block lengths, requiring frequent accelerations of vehicles, may contribute. The data also support a role for photochemical production of UFP in the afternoon. UFP concentration peaks (5 s average) of up to 9 million particles cm-3 were also observed immediately behind HEVs when they accelerated from stop lights in the BH neighborhood and areas immediately adjacent. Although encounters with HEV during mornings accounted for only about 6% and 17% of time spent monitoring residential areas and major surface streets, HEV contributed to about 28% and 53% of total ultrafine particles measured on the route, respectively. The observation of elevated pollutant concentrations across the Boyle Heights community highlights how multiple factors combine to create high pollutant levels, and has important human exposure assessment implications, including the potential utility of our data as inputs to epidemiological studies.

Exposure to Inhalable, Respirable, and Ultrafine Particles in Welding Fume

PubMed Central

Pesch, Beate

2012-01-01

This investigation aims to explore determinants of exposure to particle size-specific welding fume. Area sampling of ultrafine particles (UFP) was performed at 33 worksites in parallel with the collection of respirable particles. Personal sampling of respirable and inhalable particles was carried out in the breathing zone of 241 welders. Median mass concentrations were 2.48 mg m−3 for inhalable and 1.29 mg m−3 for respirable particles when excluding 26 users of powered air-purifying respirators (PAPRs). Mass concentrations were highest when flux-cored arc welding (FCAW) with gas was applied (median of inhalable particles: 11.6 mg m−3). Measurements of particles were frequently below the limit of detection (LOD), especially inside PAPRs or during tungsten inert gas welding (TIG). However, TIG generated a high number of small particles, including UFP. We imputed measurements

Exposure to inhalable, respirable, and ultrafine particles in welding fume.

PubMed

Lehnert, Martin; Pesch, Beate; Lotz, Anne; Pelzer, Johannes; Kendzia, Benjamin; Gawrych, Katarzyna; Heinze, Evelyn; Van Gelder, Rainer; Punkenburg, Ewald; Weiss, Tobias; Mattenklott, Markus; Hahn, Jens-Uwe; Möhlmann, Carsten; Berges, Markus; Hartwig, Andrea; Brüning, Thomas

2012-07-01

This investigation aims to explore determinants of exposure to particle size-specific welding fume. Area sampling of ultrafine particles (UFP) was performed at 33 worksites in parallel with the collection of respirable particles. Personal sampling of respirable and inhalable particles was carried out in the breathing zone of 241 welders. Median mass concentrations were 2.48 mg m(-3) for inhalable and 1.29 mg m(-3) for respirable particles when excluding 26 users of powered air-purifying respirators (PAPRs). Mass concentrations were highest when flux-cored arc welding (FCAW) with gas was applied (median of inhalable particles: 11.6 mg m(-3)). Measurements of particles were frequently below the limit of detection (LOD), especially inside PAPRs or during tungsten inert gas welding (TIG). However, TIG generated a high number of small particles, including UFP. We imputed measurements

About study of radiation flux carried out on the stand, which is designed for testing of space ultraviolet polarimeter

NASA Astrophysics Data System (ADS)

Nevodovskiy, P. V.; Vidmachenko, A. P.; Geraimchuk, M. D.; Ivahiv, O. V.

2016-08-01

In the Main Astronomical Observatory of NAS of Ukraine, National Technical University of Ukraine "KPI" and National University "Lviv Polytechnic" over the many years has accumulated considerable experience of work on the design and development of polarimeters, and created a working model of compact an onboard ultraviolet polarimeter (UFP) [1-6]. For debugging, research and testing as the entire layout of UFP and its individual parts we have created a special stand with complex equipment that allows carrying the following works. The structural construction of the stand allows obtaining characteristics as a whole unit, and its individual parts; obtaining spectral dependences and counting characteristics signal of the light radiation, and of dark signal; carry out the polarization measurements and more. For this stand developed a number of special techniques to study various parameters of all UFP appliance and its individual parts. Thus, for control - characteristics and calibration of elements of photo-detector system of electro-optical equipment, must use the reference emitters. But they are complicated and expensive. Therefore for simplified calibration and configuration of optical devices, it is expedient to use cheap and small in size, but specially selected LEDs. For this, developed for testing of UFP stand, has been modernized. Thus, the selection was carried out, and then carefully studied the sources of radiation, that will be used for calibration of polarimeters. More information on this work expounded in the report. References. 1. P. Nevodovskyi, O. Morozhenko, A. Vidmachenko, O. Ivakhiv, M. Geraimchuk, O. Zbrutskyi. Tiny Ultraviolet Polarimeter for Earth Stratosphere from Space Investigation // Proceedings of 8th IEEE International Conference on Intelligent Data Acquisition and Advanced Computing Systems: Technology and Applications (IDAACS'2015). 24-26 September 2015, Proceedings. Warsaw, Poland. Vol.81, p. 28-32. 2. Nevodovsksiy P. V., Morozhenko A. V. Studies of stratospheric ozone layer from near-earth orbit utilizing ultraviolet polarimeter // Acta Astronautica. 2009, vol. 64, no. 1, p. 54-58. 3. Nevodovskij P. V. Kvantakons and optimization of their parameters for astronomical observations // Kinematika i Fizika Nebesnykh Tel. 2001, vol. 17, no. 3, p. 279-288. 4. A. P. Vid'machenko, P. V. Nevodovsky. A cooled photomultiplier with an InGaAs photocathode developed for the spectropolarimetry observations // Kinematika i Fizika Nebesnykh Tel. 2000, Suppl. 3, p. 283-285. 5. P. Nevodovsky! i, A. Morozhenko, A. Vidmachenko, M. Geraimchuk, A. Zbrutskyi,! Yu. Kur eniov, V. Sergunin, Yu. Hirniak, O. Ivakhiv. Ultraviolet Polarimeter for Studying the Aerosol Component in the Earth Atmosphere // International Symposium on Atmospheric Radiation and Dynamics. Session 1. "Satellite sounding of atmosphere and surface". ISARD - 2013. June 24-27 2013. Peterhof, St Petersburg, Russia. P. 21.

Ultrafine particles (UFPs) from domestic wood stoves: genotoxicity in human lung carcinoma A549 cells.

PubMed

Marabini, Laura; Ozgen, Senem; Turacchi, Silvia; Aminti, Stefania; Arnaboldi, Francesca; Lonati, Giovanni; Fermo, Paola; Corbella, Lorenza; Valli, Gianluigi; Bernardoni, Vera; Dell'Acqua, Manuela; Vecchi, Roberta; Becagli, Silvia; Caruso, Donatella; Corrado, Galli L; Marinovich, Marina

2017-08-01

In this paper, results on the potential toxicity of ultrafine particles (UFPs d<100nm) emitted by the combustion of logwood and pellet (hardwood and softwood) are reported. The data were collected during the TOBICUP (TOxicity of BIomass COmbustion generated Ultrafine Particles) project, carried out by a team composed of interdisciplinary research groups. The genotoxic evaluation was performed on A549 cells (human lung carcinomacells) using UFPs whose chemical composition was assessed by a suite of analytical techniques. Comet assay and γ-H2AX evaluation show a significant DNA damage after 24h treatment. The interpretation of the results is based on the correlation among toxicological results, chemical-physical properties of UFPs, and the type and efficiency conditions in residential pellet or logwood stoves. Copyright © 2017 Elsevier B.V. All rights reserved.

Human peripheral blood mononuclear cells (PBMCs) from smokers release higher levels of IL-1-like cytokines after exposure to combustion-generated ultrafine particles.

PubMed

De Falco, Gianluigi; Terlizzi, Michela; Sirignano, Mariano; Commodo, Mario; D'Anna, Andrea; Aquino, Rita P; Pinto, Aldo; Sorrentino, Rosalinda

2017-02-22

Ultrafine particles (UFP) generated by combustion processes are often associated with adverse health effects. However, little is known about the inflammatory processes generated by UFP that may underlie their toxicological activity. Murine macrophages (J774.1 cells) and human peripheral blood mononuclear cells (PBMCs) were used to evaluate the molecular mechanism underlying the pro-inflammatory activity of UFP. The addition of soot particles to J774.1 cells induced a concentration-dependent release of IL-1α, IL-1β and IL-33 This effect was not associated with cell death and, in contrast to literature, was pronounced at very low concentrations (5-100 pg/ml). Similarly, UFP induced the release of IL-1α, IL-18 and IL-33 by PBMCs. However, this effect was solely observed in PBMCs obtained from smokers, as the PBMCs from non-smokers instead released higher levels of IL-10. The release of these cytokines after UFP exposure was caspase-1- and NLRP3 inflammasome-dependent in PBMCs from healthy smokers, whereas IL-1α release was calpain-dependent. These results show that UFP at very low concentrations are able to give rise to an inflammatory process that is responsible for IL-1α, IL-18 and IL-33 release, which is pronounced in PBMCs from smokers, confirming that these individuals are especially susceptible to inflammatory-based airway diseases once exposed to air pollution.

Human peripheral blood mononuclear cells (PBMCs) from smokers release higher levels of IL-1-like cytokines after exposure to combustion-generated ultrafine particles

PubMed Central

De Falco, Gianluigi; Terlizzi, Michela; Sirignano, Mariano; Commodo, Mario; D’Anna, Andrea; Aquino, Rita P.; Pinto, Aldo; Sorrentino, Rosalinda

2017-01-01

Ultrafine particles (UFP) generated by combustion processes are often associated with adverse health effects. However, little is known about the inflammatory processes generated by UFP that may underlie their toxicological activity. Murine macrophages (J774.1 cells) and human peripheral blood mononuclear cells (PBMCs) were used to evaluate the molecular mechanism underlying the pro-inflammatory activity of UFP. The addition of soot particles to J774.1 cells induced a concentration-dependent release of IL-1α, IL-1β and IL-33 This effect was not associated with cell death and, in contrast to literature, was pronounced at very low concentrations (5–100 pg/ml). Similarly, UFP induced the release of IL-1α, IL-18 and IL-33 by PBMCs. However, this effect was solely observed in PBMCs obtained from smokers, as the PBMCs from non-smokers instead released higher levels of IL-10. The release of these cytokines after UFP exposure was caspase-1- and NLRP3 inflammasome-dependent in PBMCs from healthy smokers, whereas IL-1α release was calpain-dependent. These results show that UFP at very low concentrations are able to give rise to an inflammatory process that is responsible for IL-1α, IL-18 and IL-33 release, which is pronounced in PBMCs from smokers, confirming that these individuals are especially susceptible to inflammatory-based airway diseases once exposed to air pollution. PMID:28223692

Associations Between Ultrafine Particles and Co-Pollutant Concentrations in the Tampa Bay Area.

PubMed

Desai, Ushang; Watson, Alain

2016-05-01

Ultrafine particles (UFPs) are ubiquitous in urban air and have been recognized as a risk to human health. The aim of this study was to measure the relationships among ultrafine particles and other ambient air pollutants and meteorological factors in the Tampa Bay Area. This study measured continuous UFPs, black carbon, oxides of nitrogen (NO(x)), nitrogen dioxide (NO2), nitric oxide (NO), carbon monoxide (CO), ozone (O3), sulfur dioxide (SO2), particulate matter having an aerodynamic diameter of 10 microns or less (PM10), relative humidity, wind speed, and ambient temperature during January to March 2014. Moreover, the study compared the relationship between UFPs and various co-pollutants daily, including during morning rush hour periods. This study found a moderate correlation among UFPs and black carbon, NO(x), NO2, and NO during hourly continuous measurements and rush hour periods, and a low level of correlation among UFPs and CO, O3, SO2, PM10, relative humidity, wind speed, and ambient temperature. This study indicates that co-pollutants should not be used as a surrogate to assess the human health risk from ultrafine particles exposure.

A modified Brownian force for ultrafine particle penetration through building crack modeling

NASA Astrophysics Data System (ADS)

Chen, Chen; Zhao, Bin

2017-12-01

Combustion processes related to industry, traffic, agriculture, and waste treatment and disposal increase the amount of outdoor ultrafine particles (UFPs), which have adverse effects on human health. Given that people spend the majority of their time indoors, it is critical to understand the penetration of outdoor UFPs through building cracks in order to estimate human exposure to outdoor-originated UFPs. Lagrangian tracking is an efficient approach for modeling particle penetration. However, the Brownian motion for Lagrangian tracking in ANSYS Fluent®, a widely used software for particle dispersion modeling, is not able to model UFP dispersion accurately. In this study, we modified the Brownian force by rewriting the Brownian diffusion coefficient and particle integration time step with a user-defined function in ANSYS Fluent® to model particle penetration through building cracks. The results obtained using the modified model agree much better with the experimental results, with the averaged relative error less than 14% for the smooth crack cases and 21% for the rough crack case. We expect the modified Brownian force model proposed herein to be applied for UFP dispersion modeling in more indoor air quality studies.

Traffic pollutants measured inside vehicles waiting in line at a major US-Mexico Port of Entry.

PubMed

Quintana, Penelope J E; Khalighi, Mehdi; Castillo Quiñones, Javier Emmanuel; Patel, Zalak; Guerrero Garcia, Jesus; Martinez Vergara, Paulina; Bryden, Megan; Mantz, Antoinette

2018-05-01

At US-Mexico border Ports of Entry, vehicles idle for long times waiting to cross northbound into the US. Long wait times at the border have mainly been studied as an economic issue, however, exposures to emissions from idling vehicles can also present an exposure risk. Here we present the first data on in-vehicle exposures to driver and passengers crossing the US-Mexico border at the San Ysidro, California Port of Entry (SYPOE). Participants were recruited who regularly commuted across the border in either direction and told to drive a scripted route between two border universities, one in the US and one in Mexico. Instruments were placed in participants' cars prior to commute to monitor-1-minute average levels of the traffic pollutants ultrafine particles (UFP), black carbon (BC) and carbon monoxide (CO) in the breathing zone of drivers and passengers. Location was determined by a GPS monitor. Results reported here are for 68 northbound participant trips. The highest median levels of in-vehicle UFP were recorded during the wait to cross at the SYPOE (median 29,692particles/cm 3 ) significantly higher than the portion of the commute in the US (median 20,508particles/cm 3 ) though not that portion in Mexico (median 22, 191particles/cm 3 ). In-vehicle BC levels at the border were significantly lower than in other parts of the commute. Our results indicate that waiting in line at the SYPOE contributes a median 62.5% (range 15.5%-86.0%) of a cross-border commuter's exposure to UFP and a median 44.5% (range (10.6-79.7%) of exposure to BC inside the vehicle while traveling in the northbound direction. Reducing border wait time can significantly reduce in-vehicle exposures to toxic air pollutants such as UFP and BC, and these preventable exposures can be considered an environmental justice issue. Copyright © 2017 Elsevier B.V. All rights reserved.

Commuter exposure to PM2.5, BC, and UFP in six common transport microenvironments in Sacramento, California

NASA Astrophysics Data System (ADS)

Ham, Walter; Vijayan, Abhilash; Schulte, Nico; Herner, Jorn D.

2017-10-01

This study was designed to estimate and compare the air pollution exposures experienced by commuters in six common transportation modes utilized by California residents, and to evaluate the impact of practical exposure mitigation strategies in reducing commute exposures. We measured concentrations of fine particle matter (PM2.5), black carbon (BC), and ultrafine particles (UFP) for 161 commutes between April 2014 and November 2015 in Sacramento, CA. We collected measurements for six modes including single occupancy vehicles, high occupancy vehicles (multiple occupants), buses, light rail, train, and bicycling. The largest average concentrations for most pollutants were measured during train commutes and the lowest average concentrations were observed during light-rail commutes. Mitigation options were explored for personal vehicles, bicycling, and train commute modes. We found that ventilation settings of personal vehicles can reduce in-vehicle PM2.5, BC, and UFP concentrations by up to 75%. Similarly, bicycle route choice can reduce exposures by 15-75% with the lowest concentrations observed during commutes on dedicated bicycle paths away from traffic sources. Train commuters experienced UFP concentrations an order of magnitude greater when the locomotive engine was pulling the rail cars versus pushing the rail cars. We found that UFP concentrations during bus, bicycling, and train commutes were 1.6-5.3 times greater than personal vehicle commutes, while light rail commutes had 30% lower UFP concentrations than personal vehicle commutes. The largest exposure per mile occurred during bicycle commutes with PM2.5, BC, and UFP exposures of 1.312 μg/mile, 0.097 μg/mile, and 3.0 × 109 particles/mile, respectively. Train commutes experienced the largest exposure per mile of all of the combustion-derived transportation commute modes. BC accounted for 5-20% of total PM mass across all commute modes with an average fraction of ∼7% of PM2.5.

Long-term exposure to ambient ultrafine particles and respiratory disease incidence in in Toronto, Canada: a cohort study.

PubMed

Weichenthal, Scott; Bai, Li; Hatzopoulou, Marianne; Van Ryswyk, Keith; Kwong, Jeffrey C; Jerrett, Michael; van Donkelaar, Aaron; Martin, Randall V; Burnett, Richard T; Lu, Hong; Chen, Hong

2017-06-19

Little is known about the long-term health effects of ambient ultrafine particles (<0.1 μm) (UFPs) including their association with respiratory disease incidence. In this study, we examined the relationship between long-term exposure to ambient UFPs and the incidence of lung cancer, adult-onset asthma, and chronic obstructive pulmonary disease (COPD). Our study cohort included approximately 1.1 million adults who resided in Toronto, Canada and who were followed for disease incidence between 1996 and 2012. UFP exposures were assigned to residential locations using a land use regression model. Random-effect Cox proportional hazard models were used to estimate hazard ratios (HRs) describing the association between ambient UFPs and respiratory disease incidence adjusting for ambient fine particulate air pollution (PM 2.5 ), NO 2 , and other individual/neighbourhood-level covariates. In total, 74,543 incident cases of COPD, 87,141 cases of asthma, and 12,908 cases of lung cancer were observed during follow-up period. In single pollutant models, each interquartile increase in ambient UFPs was associated with incident COPD (HR = 1.06, 95% CI: 1.05, 1.09) but not asthma (HR = 1.00, 95% CI: 1.00, 1.01) or lung cancer (HR = 1.00, 95% CI: 0.97, 1.03). Additional adjustment for NO 2 attenuated the association between UFPs and COPD and the HR was no longer elevated (HR = 1.01, 95% CI: 0.98, 1.03). PM 2.5 and NO 2 were each associated with increased incidence of all three outcomes but risk estimates for lung cancer were sensitive to indirect adjustment for smoking and body mass index. In general, we did not observe clear evidence of positive associations between long-term exposure to ambient UFPs and respiratory disease incidence independent of other air pollutants. Further replication is required as few studies have evaluated these relationships.

On-road ultrafine particle concentration in the M5 East road tunnel, Sydney, Australia

NASA Astrophysics Data System (ADS)

Knibbs, Luke D.; de Dear, Richard J.; Morawska, Lidia; Mengersen, Kerrie L.

The human health effects following exposure to ultrafine (<100 nm) particles (UFPs) produced by fuel combustion, while not completely understood, are generally regarded as detrimental. Road tunnels have emerged as locations where maximum exposure to these particles may occur for the vehicle occupants using them. This study aimed to quantify and investigate the determinants of UFP concentrations in the 4 km twin-bore (eastbound and westbound) M5 East tunnel in Sydney, Australia. Sampling was undertaken using a condensation particle counter (CPC) mounted in a vehicle traversing both tunnel bores at various times of day from May through July, 2006. Supplementary measurements were conducted in February, 2008. Over three hundred transects of the tunnel were performed, and these were distributed evenly between the bores. Additional comparative measurements were conducted on a mixed route comprising major roads and shorter tunnels, all within Sydney. Individual trip average UFP concentrations in the M5 East tunnel bores ranged from 5.53 × 10 4 p cm -3 to 5.95 × 10 6 p cm -3. Data were sorted by hour of capture, and hourly median trip average (HMA) UFP concentrations ranged from 7.81 × 10 4 p cm -3 to 1.73 × 10 6 p cm -3. Hourly median UFP concentrations measured on the mixed route were between 3.71 × 10 4 p cm -3 and 1.55 × 10 5 p cm -3. Hourly heavy diesel vehicle (HDV) traffic volume was a very good determinant of UFP concentration in the eastbound tunnel bore ( R2 = 0.87), but much less so in the westbound bore ( R2 = 0.26). In both bores, the volume of passenger vehicles (i.e. unleaded gasoline-powered vehicles) was a significantly poorer determinant of particle concentration. When compared with similar studies reported previously, the measurements described here were among the highest recorded concentrations, which further highlights the contribution road tunnels may make to the overall UFP exposure of vehicle occupants.

Pharmacological characterization of the bifunctional opioid ligand H-Dmt-Tic-Gly-NH-Bzl (UFP-505).

PubMed

Dietis, N; McDonald, J; Molinari, S; Calo, G; Guerrini, R; Rowbotham, D J; Lambert, D G

2012-02-01

While producing good-quality analgesia, µ-opioid (MOP) receptor activation produces a number of side-effects including tolerance. Simultaneous blockade of δ-opioid (DOP) receptors has been shown to reduce tolerance to morphine. Here, we characterize a prototype bifunctional opioid H-Dmt-Tic-Gly-NH-Bzl (UFP-505). We measured receptor binding affinity in Chinese hamster ovary (CHO) cells expressing recombinant human MOP, DOP, k-opioid (KOP), nociceptin/orphanin (NOP) receptors. For activation, we measured the binding of GTPγ(35)S to membranes from CHO(hMOP), CHO(hDOP), rat cerebrocortex, and rat spinal cord. In addition, we assessed 'end organ' responses in the guinea pig ileum and mouse vas deferens. UFP-505 bound to CHO(hMOP) and CHO(hDOP) with (binding affinity) pK(i) values of 7.79 and 9.82, respectively. There was a weak interaction at KOP and NOP (pK(i) 6.29 and 5.86). At CHO(hMOP), UFP-505 stimulated GTPγ(35)S binding with potency (pEC(50)) of 6.37 and in CHO(hDOP) reversed the effects of a DOP agonist with affinity (pK(b)) of 9.81 (in agreement with pK(i) at DOP). UFP-505 also stimulated GTPγ(35)S binding in rat cerebrocortex and spinal cord with pEC(50) values of 6.11-6.53. In the guinea pig ileum (MOP-rich preparation), UFP-505 inhibited contractility with pEC(50) of 7.50 and in the vas deferens (DOP-rich preparation) reversed the effects of a DOP agonist with an affinity (pA(2)) of 9.15. We have shown in a range of preparations and assays that UFP-505 behaves as a potent MOP agonist and DOP antagonist; a MOP/DOP bifunctional opioid. Further studies in dual expression systems and whole animals with this prototype are warranted.

Local lung deposition of ultrafine particles in healthy adults: experimental results and theoretical predictions.

PubMed

Sturm, Robert

2016-11-01

Ultrafine particles (UFP) of biogenic and anthropogenic origin occur in high numbers in the ambient atmosphere. In addition, aerosols containing ultrafine powders are used for the inhalation therapy of various diseases. All these facts make it necessary to obtain comprehensive knowledge regarding the exact behavior of UFP in the respiratory tract. Theoretical simulations of local UFP deposition are based on previously conducted inhalation experiments, where particles with various sizes (0.04, 0.06, 0.08, and 0.10 µm) were administered to the respiratory tract by application of the aerosol bolus technique. By the sequential change of the lung penetration depth of the inspired bolus, different volumetric lung regions could be generated and particle deposition in these regions could be evaluated. The model presented in this contribution adopted all parameters used in the experiments. Besides the obligatory comparison between practical and theoretical data, also advanced modeling predictions including the effect of varying functional residual capacity (FRC) and respiratory flow rate were conducted. Validation of the UFP deposition model shows that highest deposition fractions occur in those volumetric lung regions corresponding to the small and partly alveolated airways of the tracheobronchial tree. Particle deposition proximal to the trachea is increased in female probands with respect to male subjects. Decrease of both the FRC and the respiratory flow rate results in an enhancement of UFP deposition. The study comes to the conclusion that deposition of UFP taken up via bolus inhalation is influenced by a multitude of factors, among which lung morphometry and breathing conditions play a superior role.

Local lung deposition of ultrafine particles in healthy adults: experimental results and theoretical predictions

PubMed Central

2016-01-01

Background Ultrafine particles (UFP) of biogenic and anthropogenic origin occur in high numbers in the ambient atmosphere. In addition, aerosols containing ultrafine powders are used for the inhalation therapy of various diseases. All these facts make it necessary to obtain comprehensive knowledge regarding the exact behavior of UFP in the respiratory tract. Methods Theoretical simulations of local UFP deposition are based on previously conducted inhalation experiments, where particles with various sizes (0.04, 0.06, 0.08, and 0.10 µm) were administered to the respiratory tract by application of the aerosol bolus technique. By the sequential change of the lung penetration depth of the inspired bolus, different volumetric lung regions could be generated and particle deposition in these regions could be evaluated. The model presented in this contribution adopted all parameters used in the experiments. Besides the obligatory comparison between practical and theoretical data, also advanced modeling predictions including the effect of varying functional residual capacity (FRC) and respiratory flow rate were conducted. Results Validation of the UFP deposition model shows that highest deposition fractions occur in those volumetric lung regions corresponding to the small and partly alveolated airways of the tracheobronchial tree. Particle deposition proximal to the trachea is increased in female probands with respect to male subjects. Decrease of both the FRC and the respiratory flow rate results in an enhancement of UFP deposition. Conclusions The study comes to the conclusion that deposition of UFP taken up via bolus inhalation is influenced by a multitude of factors, among which lung morphometry and breathing conditions play a superior role. PMID:27942511

Air quality in the German-Czech border region: A focus on harmful fractions of PM and ultrafine particles

NASA Astrophysics Data System (ADS)

Schladitz, Alexander; Leníček, Jan; Beneš, Ivan; Kováč, Martin; Skorkovský, Jiří; Soukup, Aleš; Jandlová, Jana; Poulain, Laurent; Plachá, Helena; Löschau, Gunter; Wiedensohler, Alfred

2015-12-01

A comprehensive air quality study has been carried out at two urban background sites in Annaberg-Buchholz (Germany) and Ústí nad Labem (Czech Republic) in the German-Czech border region between January 2012 and June 2014. Special attention was paid to quantify harmful fractions of particulate matter (PM) and ultrafine particle number concentration (UFP) from solid fuel combustion and vehicular traffic. Source type contributions of UFP were quantified by using the daily concentration courses of UFP and nitrogen oxide. Two different source apportionment techniques were used to quantify relative and absolute mass contributions: positive matrix factorization for total PM2.5 and elemental carbon in PM2.5 and chemical mass balance for total PM1 and organic carbon in PM1. Contributions from solid fuel combustion strongly differed between the non-heating period (April-September) and the heating period (October-March). Major sources of solid fuel combustion in this study were wood and domestic coal combustion, while the proportion of industrial coal combustion was low (<3%). In Ústí nad Labem combustion of domestic brown coal was the most important source of organic carbon ranging from 34% to 43%. Wood combustion was an important source of organic carbon in Annaberg-Buchholz throughout the year. Heavy metals and less volatile polycyclic aromatic hydrocarbons (PAH) in the accumulation mode were related to solid fuel combustion with enhanced concentrations during the heating period. In contrast, vehicular PAH emissions were allocated to the Aitken mode. Only in Ústí nad Labem a significant contribution of photochemical new particle formation (e.g. from sulfur dioxide) to UFP of almost 50% was observed during noontime. UFPs from traffic emissions (nucleation particles) and primary emitted soot particles dominated at both sites during the rest of the day. The methodology of a combined source apportionment of UFP and PM can be adapted to other regions of the world with similar problems of atmospheric pollution to calculate the relative risk in epidemiological health studies for different sub-fractions of PM and UFP. This will enhance the meaningfulness of published relative risks in health studies based on total PM and UFP number concentrations.

Nanoparticles: Health Effects—Pros and Cons

PubMed Central

Gwinn, Maureen R.; Vallyathan, Val

2006-01-01

With the advent of nanotechnology, the prospects for using engineered nanomaterials with diameters of < 100 nm in industrial applications, medical imaging, disease diagnoses, drug delivery, cancer treatment, gene therapy, and other areas have progressed rapidly. The potential for nanoparticles (NPs) in these areas is infinite, with novel new applications constantly being explored. The possible toxic health effects of these NPs associated with human exposure are unknown. Many fine particles generally considered “nuisance dusts” are likely to acquire unique surface properties when engineered to nanosize and may exhibit toxic biological effects. Consequently, the nuisance dust may be transported to distant sites and could induce adverse health effects. In addition the beneficial uses of NPs in drug delivery, cancer treatment, and gene therapy may cause unintentional human exposure. Because of our lack of knowledge about the health effects associated with NP exposure, we have an ethical duty to take precautionary measures regarding their use. In this review we highlight the possible toxic human health effects that can result from exposure to ultrafine particles (UFPs) generated by anthropogenic activities and their cardiopulmonary outcomes. The comparability of engineered NPs to UFPs suggests that the human health effects are likely to be similar. Therefore, it is prudent to elucidate their toxicologic effect to minimize occupational and environmental exposure. Highlighting the human health outcomes caused by UFPs is not intended to give a lesser importance to either the unprecedented technologic and industrial rewards of the nanotechnology or their beneficial human uses. PMID:17185269

Nanoparticles: health effects--pros and cons.

PubMed

Gwinn, Maureen R; Vallyathan, Val

2006-12-01

With the advent of nanotechnology, the prospects for using engineered nanomaterials with diameters of < 100 nm in industrial applications, medical imaging, disease diagnoses, drug delivery, cancer treatment, gene therapy, and other areas have progressed rapidly. The potential for nanoparticles (NPs) in these areas is infinite, with novel new applications constantly being explored. The possible toxic health effects of these NPs associated with human exposure are unknown. Many fine particles generally considered "nuisance dusts" are likely to acquire unique surface properties when engineered to nanosize and may exhibit toxic biological effects. Consequently, the nuisance dust may be transported to distant sites and could induce adverse health effects. In addition the beneficial uses of NPs in drug delivery, cancer treatment, and gene therapy may cause unintentional human exposure. Because of our lack of knowledge about the health effects associated with NP exposure, we have an ethical duty to take precautionary measures regarding their use. In this review we highlight the possible toxic human health effects that can result from exposure to ultrafine particles (UFPs) generated by anthropogenic activities and their cardiopulmonary outcomes. The comparability of engineered NPs to UFPs suggests that the human health effects are likely to be similar. Therefore, it is prudent to elucidate their toxicologic effect to minimize occupational and environmental exposure. Highlighting the human health outcomes caused by UFPs is not intended to give a lesser importance to either the unprecedented technologic and industrial rewards of the nanotechnology or their beneficial human uses.

Ultrafine Particulate Matter Increases Cardiac Ischemia/Reperfusion Injury via Mitochondrial Permeability Transition Pore.

EPA Science Inventory

Ultrafine Particulate Matter (UFP) has been associated with increased cardiovascular morbidity and mortality. However, the mechanisms that drive PM associated cardiovascular disease and dysfunction remain unclear. We examined the impact of intratracheal instillation of 100 g UFP...

Association of ultrafine particles with cardiopulmonary health among adult subjects in the urban areas of northern Taiwan.

PubMed

Liu, Jun-Yu; Hsiao, Ta-Chih; Lee, Kang-Yun; Chuang, Hsiao-Chi; Cheng, Tsun-Jen; Chuang, Kai-Jen

2018-06-15

The association between short-term exposure to particulate air pollution, especially fine particles, and cardiopulmonary health has been well-established in previous studies. However, previous findings regarding the effect of ultrafine particles (UFPs) on cardiopulmonary health are inconsistent. We repeatedly measured the mass concentrations of UFPs using a Micro-Orifice Uniform Deposit Impactor (MOUDI) in the apartments of 100 adult participants and collected the participants' health data from the pulmonary outpatient unit of Shuang-Ho Hospital to investigate the association between short-term exposure to UFPs and cardiopulmonary health using mixed-effects models from January 1, 2014 to August 31, 2017. We also collected ambient air pollution monitoring data from the Taiwan Environmental Protection Administration for data analysis. We observed that an interquartile range increase in the 24-hour mean UFPs (0.97 μg/m 3 ) was associated with a 6.3% [95% confidence interval (CI) = 2.9, 9.7], 5.6% (95% CI = 4.1, 7.1) and 8.5% (95% CI = 3.9, 13.1) increase in systolic blood pressure, diastolic blood pressure and high sensitivity-C-reactive protein, respectively. We also observed the association of particulate matter less than or equal to 2.5 μm in diameter and nitrogen dioxide with increased blood pressure and ozone with decreased lung function. A negative trend between UFPs and forced expiratory volume in the first second was observed. We concluded that short-term exposure to UFPs was associated with cardiovascular health in adult subjects in the urban areas of northern Taiwan. Copyright © 2018 Elsevier B.V. All rights reserved.

Physico-chemical properties and biological effects of diesel and biomass particles.

PubMed

Longhin, Eleonora; Gualtieri, Maurizio; Capasso, Laura; Bengalli, Rossella; Mollerup, Steen; Holme, Jørn A; Øvrevik, Johan; Casadei, Simone; Di Benedetto, Cristiano; Parenti, Paolo; Camatini, Marina

2016-08-01

Diesel combustion and solid biomass burning are the major sources of ultrafine particles (UFP) in urbanized areas. Cardiovascular and pulmonary diseases, including lung cancer, are possible outcomes of combustion particles exposure, but differences in particles properties seem to influence their biological effects. Here the physico-chemical properties and biological effects of diesel and biomass particles, produced under controlled laboratory conditions, have been characterized. Diesel UFP were sampled from a Euro 4 light duty vehicle without DPF fuelled by commercial diesel and run over a chassis dyno. Biomass UFP were collected from a modern automatic 25 kW boiler propelled by prime quality spruce pellet. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) images of both diesel and biomass samples showed aggregates of soot particles, but in biomass samples ash particles were also present. Chemical characterization showed that metals and PAHs total content was higher in diesel samples compared to biomass ones. Human bronchial epithelial (HBEC3) cells were exposed to particles for up to 2 weeks. Changes in the expression of genes involved in xenobiotic metabolism were observed after exposure to both UFP already after 24 h. However, only diesel particles modulated the expression of genes involved in inflammation, oxidative stress and epithelial-to-mesenchymal transition (EMT), increased the release of inflammatory mediators and caused phenotypical alterations, mostly after two weeks of exposure. These results show that diesel UFP affected cellular processes involved in lung and cardiovascular diseases and cancer. Biomass particles exerted low biological activity compared to diesel UFP. This evidence emphasizes that the study of different emission sources contribution to ambient PM toxicity may have a fundamental role in the development of more effective strategies for air quality improvement. Copyright © 2016 Elsevier Ltd. All rights reserved.

Inhalation of ultrafine carbon particles alters heart rate and heart rate variability in people with type 2 diabetes.

PubMed

Vora, Rathin; Zareba, Wojciech; Utell, Mark J; Pietropaoli, Anthony P; Chalupa, David; Little, Erika L; Oakes, David; Bausch, Jan; Wiltshire, Jelani; Frampton, Mark W

2014-07-16

Diabetes may confer an increased risk for the cardiovascular health effects of particulate air pollution, but few human clinical studies of air pollution have included people with diabetes. Ultrafine particles (UFP, ≤100 nm in diameter) have been hypothesized to be an important component of particulate air pollution with regard to cardiovascular health effects. 17 never-smoker subjects 30-60 years of age, with stable type 2 diabetes but otherwise healthy, inhaled either filtered air (0-10 particles/cm3) or elemental carbon UFP (~107 particles/cm3, ~50 ug/m3, count median diameter 32 nm) by mouthpiece, for 2 hours at rest, in a double-blind, randomized, crossover study design. A digital 12-lead electrocardiogram (ECG) was recorded continuously for 48 hours, beginning 1 hour prior to exposure. Analysis of 5-minute segments of the ECG during quiet rest showed reduced high-frequency heart rate variability with UFP relative to air exposure (p = 0.014), paralleled by non-significant reductions in time-domain heart rate variability parameters. In the analysis of longer durations of the ECG, we found that UFP exposure increased the heart rate relative to air exposure. During the 21- to 45-hour interval after exposure, the average heart rate increased approximately 8 beats per minute with UFP, compared to 5 beats per minute with air (p = 0.045). There were no UFP effects on cardiac rhythm or repolarization. Inhalation of elemental carbon ultrafine particles alters heart rate and heart rate variability in people with type 2 diabetes. Our findings suggest that effects may occur and persist hours after a single 2-hour exposure.

Nutritive value of methane fermentation residue in diets fed to feedlot steers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, J.M.; Shirley, R.L.; Palmer, A.Z.

1982-12-01

Nutritive value of the methane fermentation residue (MFR) from the effluent of a large scale thermophilic methane generator was determined in diets fed to feedlot steers. The MFR contained 22.2% dry matter and 21.9% crude protein (dry basis). Two diets containing 10.6% (dry basis) MFR were formulated using the Urea Fermentation Potential (UFP) system such that in one diet N was in excess (-1.6 UFP) while in the other diet energy was in excess (+2.6 UFP). These two diets were compared in a California Net Energy trial with a feedlot diet (-.3 UFP) containing the same ingredients except the MFR.more » Six steers were fed in a replicated 3(2) Latin square metabolism trial and 70 steers were fed in a 118-d comparative-slaughter, feedlot trial. Digestibilities of dry matter, organic matter, crude protein, acid detergent fiber, ash, total digestible nutrients (TDN) and metabolizable energy were depressed (all P less than .05) in the MFR-containing diets. Steers fed the MFR-containing diets had lower (P less than .05) rates of gain and increased (P less than .05) feed requirements per unit gain. Net energies for maintenance and gain were slightly lower for the MFR-containing diets than the control diet. Crude protein digestibility for the MFR calculated by difference, for the -UFP and the +UFP diets were 37.8 and 50.7%, while corresponding values for TDN were 28.8 and 12.8%, respectively. Concentrations of potentially toxic elements in kidney, liver and muscle as well as flavor and tenderness of steaks were not affected by feeding MFR.« less

Field evaluation of vegetation and noise barriers for mitigation of near-freeway air pollution under variable wind conditions

NASA Astrophysics Data System (ADS)

Lee, Eon S.; Ranasinghe, Dilhara R.; Ahangar, Faraz Enayati; Amini, Seyedmorteza; Mara, Steven; Choi, Wonsik; Paulson, Suzanne; Zhu, Yifang

2018-02-01

Traffic-related air pollutants are a significant public health concern, particularly near freeways. Previous studies have suggested either soundwall or vegetation barriers might reduce the near-freeway air pollution. This study aims to investigate the effectiveness of a combination of both soundwall and vegetation barrier for reducing ultrafine particles (UFPs, diameter ≤ 100 nm) and PM2.5 (diameter ≤ 2.5 μm) concentrations. Concurrent data collection was carried out at both upwind and downwind fixed locations approximately 10-15 m away from the edge of two major freeways in California. This study observed that the reduction of UFP and PM2.5 was generally greater with the combination barrier than with either soundwall or vegetation alone. Since there were no non-barrier sites at the study locations, the reductions reported here are all in relative terms. The soundwall barrier was more effective for reducing PM2.5 (25-53%) than UFPs (0-5%), and was most effective (51-53% for PM2.5) when the wind speed ranged between 1 and 2 m/s. Under the same range of wind speed, the vegetation barrier had little effect (0-5%) on reducing PM2.5; but was effective at reducing UFP (up to 50%). For both types of roadside barrier, decreasing wind speed resulted in greater net reduction of UFPs (i.e., total number particle concentrations; inversely proportional). This trend was observed, however, only within specific particle size ranges (i.e., diameter < 20 nm for the soundwall barrier and 12-60 nm for the vegetation barrier). Out of these size ranges, the reduction of UFP concentration was proportional to increasing wind speed. Overall findings of this study support positive effects of soundwall and vegetation barriers for near-freeway air pollution mitigation.

OXIDATIVE STRESS AND LIPID MEDIATORS INDUCED IN ALVEOLAR MACHROPHAGES BY ULTRAFINE PARTICLES

EPA Science Inventory

In ambient aerosols, ultrafine particles (UFP) and their agglomerates are considered to be major factors contributing to adverse health effects. Reactivity of agglomerated UFP of elemental carbon (EC), Printex 90, Printex G, and diesel exhaust particles (DEP) was evaluated by the...

Manufactured and Airborne Nanoparticle Cardiopulmonary Interactions: A Review of Mechanisms and the Possible Contribution of Mast Cells

EPA Science Inventory

Human inhalation exposures to manufactured nanoparticles (NP) and airborne ultrafine particles (UFP) continues to increase in both occupational and environmental settings. UFP exposures have been associated with increased cardiovascular mortality and morbidity, while ongoing res...

Beyond PM2.5: The role of ultrafine particles on adverse health effects of air pollution.

PubMed

Chen, Rui; Hu, Bin; Liu, Ying; Xu, Jianxun; Yang, Guosheng; Xu, Diandou; Chen, Chunying

2016-12-01

Air pollution constitutes the major threat to human health, whereas their adverse impacts and underlying mechanisms of different particular matters are not clearly defined. Ultrafine particles (UFPs) are high related to the anthropogenic emission sources, i.e. combustion engines and power plants. Their composition, source, typical characters, oxidative effects, potential exposure routes and health risks were thoroughly reviewed. UFPs play a major role in adverse impacts on human health and require further investigations in future toxicological research of air pollution. Unlike PM2.5, UFPs may have much more impacts on human health considering loads of evidences emerging from particulate matters and nanotoxicology research fields. The knowledge of nanotoxicology contributes to the understanding of toxicity mechanisms of airborne UFPs in air pollution. This article is part of a Special Issue entitled Air Pollution, edited by Wenjun Ding, Andrew J. Ghio and Weidong Wu. Copyright © 2016 Elsevier B.V. All rights reserved.

Ultrafine particle levels at an international port of entry between the US and Mexico: exposure implications for users, workers, and neighbors.

PubMed

Olvera, Hector A; Lopez, Mario; Guerrero, Veronica; Garcia, Humberto; Li, Wen-Whai

2013-01-01

Exposure to diesel-emitted particles has been linked to increased cancer risk and cardiopulmonary diseases. Because of their size (<100 nm), exposure to ultrafine particles (UFPs) emitted from heavy-duty diesel vehicles (HDDV) might result in greater health risks than those associated with larger particles. Seasonal UFP levels at the International Bridge of the Americas, which connects the US and Mexico and has high HDDV traffic demands, were characterized. Hourly average UFP concentrations ranged between 1.7 × 10(3)/cc and 2.9 × 10(5)/cc with a mean of 3.5 × 10(4)/cc. Wind speeds <2 m s(-1) and temperatures <15 °C were associated with particle number concentrations above normal conditions. The presence of HDDV had the strongest impact on local UFP levels. Varying particle size distributions were associated with south- and northbound HDDV traffic. Peak exposure occurred on weekday afternoons. Although in winter, high exposure episodes were also observed in the morning. Particle number concentrations were estimated to reach background levels at 400 m away from traffic. The populations exposed to UFP above background levels include law enforcement officers, street vendors, private commuters, and commercial vehicle drivers as well as neighbors on both sides of the border, including a church and several schools.

Health risks caused by short term exposure to ultrafine particles generated by residential wood combustion: a case study of Temuco, Chile.

PubMed

Díaz-Robles, Luis A; Fu, Joshua S; Vergara-Fernández, Alberto; Etcharren, Pablo; Schiappacasse, Luis N; Reed, Gregory D; Silva, María P

2014-05-01

Temuco is one of the most highly wood smoke polluted cities in Chile; however, there is scarce evidence of respiratory morbidity due to fine particulate matter. We aimed to estimate the relationship between daily concentration of ultrafine particles (UFP), with an aerodynamic diameter ≤ 0.1 μm, and outpatient visits for respiratory illness at medical care centers of Temuco, Chile, from August the 20th, 2009 to June the 30th, 2011. The Air Pollution Health Effects European Approach (APHEA2) protocol was followed, and a multivariate semi-parametric Poisson regression model was fitted with GAM techniques using R-Project statistical package; controlling for trend, seasonality, and confounders. The daily UFP were measured by a MOUDI NR-110 sampler. We found that results of the statistical analyses show significant associations between UFP and respiratory outpatient visits, with the elderly (population ≥ 65 years), being the group that presented the greatest risk. An interquartile increase of 4.73 μg/m(3) in UFP (lag 5 days) was associated with respiratory outpatient visits with a relative risk (RR) of 1.1458 [95% CI (1.0497-1.2507)] for the elderly. These results show novel findings regarding the relevance of daily UFP concentrations and health risk, especially for susceptible population in a wood smoke polluted city. Copyright © 2014 Elsevier Ltd. All rights reserved.

Ambient Ultrafine Particle Ingestion Alters Gut Microbiota in Association with Increased Atherogenic Lipid Metabolites

PubMed Central

Li, Rongsong; Yang, Jieping; Saffari, Arian; Jacobs, Jonathan; Baek, Kyung In; Hough, Greg; Larauche, Muriel H.; Ma, Jianguo; Jen, Nelson; Moussaoui, Nabila; Zhou, Bill; Kang, Hanul; Reddy, Srinivasa; Henning, Susanne M.; Campen, Matthew J.; Pisegna, Joseph; Li, Zhaoping; Fogelman, Alan M.; Sioutas, Constantinos; Navab, Mohamad; Hsiai, Tzung K.

2017-01-01

Ambient particulate matter (PM) exposure is associated with atherosclerosis and inflammatory bowel disease. Ultrafine particles (UFP, dp < 0.1–0.2 μm) are redox active components of PM. We hypothesized that orally ingested UFP promoted atherogenic lipid metabolites in both the intestine and plasma via altered gut microbiota composition. Low density lipoprotein receptor-null (Ldlr−/−) mice on a high-fat diet were orally administered with vehicle control or UFP (40 μg/mouse/day) for 3 days a week. After 10 weeks, UFP ingested mice developed macrophage and neutrophil infiltration in the intestinal villi, accompanied by elevated cholesterol but reduced coprostanol levels in the cecum, as well as elevated atherogenic lysophosphatidylcholine (LPC 18:1) and lysophosphatidic acids (LPAs) in the intestine and plasma. At the phylum level, Principle Component Analysis revealed significant segregation of microbiota compositions which was validated by Beta diversity analysis. UFP-exposed mice developed increased abundance in Verrocomicrobia but decreased Actinobacteria, Cyanobacteria, and Firmicutes as well as a reduced diversity in microbiome. Spearman’s analysis negatively correlated Actinobacteria with cecal cholesterol, intestinal and plasma LPC18:1, and Firmicutes and Cyanobacteria with plasma LPC 18:1. Thus, ultrafine particles ingestion alters gut microbiota composition, accompanied by increased atherogenic lipid metabolites. These findings implicate the gut-vascular axis in a atherosclerosis model. PMID:28211537

[Ultrafine particles and effects on the body: review of the literature].

PubMed

Pedata, P; Garzillo, E M; Sannolo, N

2010-01-01

The International laws and the technology developments led to a situation where the current levels of environmental pollution are below those that existed at the beginning of the century: however, these pollution levels produce harmful effects to health linked to an increase in morbidity and mortality. Over the years the pollution has changed: following the transformation of heating, motor innovation and emissions reducing, has been a reduction in air concentration of some conventional pollutants (sulfur dioxide, carbon monoxide, benzene), while there wasn't a significant reduction of particulate air pollution. In this work have been questioned several electronic databases of scientific literature based on a selection algorithm that contains expressions for the following topics: "ultrafine particles", "effects on human health", "occupational and environmental exposure". We analyzed 200 articles, progressively reduced to 88, selected for keywords, year of publication and arguments; the main topics covered by the articles were related to chemical and physical UFP properties, UFP exposure, European legislation relating to the values of particle concentrations in the atmosphere, toxicokinetics and effects on various organs such as, in particular, the respiratory system, cardiovascular system, central nervous system and the intracellular mechanism of action. Analysis of the literature showed that ultrafine particles (PM0.1 aerodynamic diameter less than 0.1 microm) are more powerful than the coarse particle fraction (2.5-10 microm) and fine (0.1-2.5 microm) in inducing adverse effects to human health. Unfortunately, the study of mechanisms of action of these particles presents particular difficulties because of the large number of chemical and biological mechanisms that come into play in the body after exposure to ultrafine particles.

CARDIOVASCULAR RESPONSES IN UNRESTRAINED WKY-RATS TO INHALED ULTRAFINE CARBON PARTICLES

EPA Science Inventory

Abstract
This study provides evidence for adverse cardiac effects of inhaled ultrafine particles (UFPs) in healthy WKY rats. Short term exposure (24 h) with carbon UFPs (180 ?g?m ?) induced a moderate but significant heart rate increase of 18 bpm (4.8 %) in association with a ...

3D Printing. What's the Harm?

ERIC Educational Resources Information Center

Love, Tyler S.; Roy, Ken

2016-01-01

Health concerns from 3D printing were first documented by Stephens, Azimi, Orch, and Ramos (2013), who found that commercially available 3D printers were producing hazardous levels of ultrafine particles (UFPs) and volatile organic compounds (VOCs) when plastic materials were melted through the extruder. UFPs are particles less than 100 nanometers…

Personal exposure to ultrafine particles: the influence of time-activity patterns.

PubMed

Buonanno, G; Stabile, L; Morawska, L

2014-01-15

Exposure to ultrafine particles (UFPs) is deemed to be a major risk affecting human health. Therefore, airborne particle studies were performed in the recent years to evaluate the most critical micro-environments, as well as identifying the main UFP sources. Nonetheless, in order to properly evaluate the UFP exposure, personal monitoring is required as the only way to relate particle exposure levels to the activities performed and micro-environments visited. To this purpose, in the present work, the results of experimental analysis aimed at showing the effect of the time-activity patterns on UFP personal exposure are reported. In particular, 24 non-smoking couples (12 during winter and summer time, respectively), comprised of a man who worked full-time and a woman who was a homemaker, were analyzed using personal particle counter and GPS monitors. Each couple was investigated for a 48-h period, during which they also filled out a diary reporting the daily activities performed. Time activity patterns, particle number concentration exposure and the related dose received by the participants, in terms of particle alveolar-deposited surface area, were measured. The average exposure to particle number concentration was higher for women during both summer and winter (Summer: women 1.8 × 10(4) part. cm(-3); men 9.2 × 10(3) part. cm(-3); Winter: women 2.9 × 10(4) part. cm(-3); men 1.3 × 10(4) part. cm(-3)), which was likely due to the time spent undertaking cooking activities. Staying indoors after cooking also led to higher alveolar-deposited surface area dose for both women and men during the winter time (9.12 × 10(2) and 6.33 × 10(2) mm(2), respectively), when indoor ventilation was greatly reduced. The effect of cooking activities was also detected in terms of women's dose intensity (dose per unit time), being 8.6 and 6.6 in winter and summer, respectively. On the contrary, the highest dose intensity activity for men was time spent using transportation (2.8 in both winter and summer). © 2013.

A Laboratory Comparison of Emission Factors, Number Size Distributions, and Morphology of Ultrafine Particles from 11 Different Household Cookstove-Fuel Systems

EPA Science Inventory

Ultrafine particle (UFP) emissions and particle number size distributions (PNSD) are critical in the evaluation of air pollution impacts on human health and climate change. Residential cookstove emissions are a major source of many air pollutants; however, data on UFP number emis...

Ultrafine particles near a major roadway in Raleigh, North Carolina: downwind attenuation and correlation with traffic-related pollutants

EPA Science Inventory

Ultrafine particles (UFPs, diameter <100 run) emitted by traffic are a potential direct health threat to nearby populations and may additionally act as a tracer for co-emitted pollutants. During summertime in Raleigh, North Carolina, UFPs were simultaneously measured upwind and d...

Characterizing the spatial distribution of ambient ultrafine particles in Toronto, Canada: A land use regression model.

PubMed

Weichenthal, Scott; Van Ryswyk, Keith; Goldstein, Alon; Shekarrizfard, Maryam; Hatzopoulou, Marianne

2016-01-01

Exposure models are needed to evaluate the chronic health effects of ambient ultrafine particles (<0.1 μm) (UFPs). We developed a land use regression model for ambient UFPs in Toronto, Canada using mobile monitoring data collected during summer/winter 2010-2011. In total, 405 road segments were included in the analysis. The final model explained 67% of the spatial variation in mean UFPs and included terms for the logarithm of distances to highways, major roads, the central business district, Pearson airport, and bus routes as well as variables for the number of on-street trees, parks, open space, and the length of bus routes within a 100 m buffer. There was no systematic difference between measured and predicted values when the model was evaluated in an external dataset, although the R(2) value decreased (R(2) = 50%). This model will be used to evaluate the chronic health effects of UFPs using population-based cohorts in the Toronto area. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Exposure assessment of a cyclist to PM10 and ultrafine particles.

PubMed

Berghmans, P; Bleux, N; Int Panis, L; Mishra, V K; Torfs, R; Van Poppel, M

2009-02-01

Estimating personal exposure to air pollution is a crucial component in identifying high-risk populations and situations. It will enable policy makers to determine efficient control strategies. Cycling is again becoming a favorite mode of transport both in developing and in developed countries due to increasing traffic congestion and environmental concerns. In Europe, it is also seen as a healthy sports activity. However, due to high levels of hazardous pollutants in the present day road microenvironment the cyclist might be at a higher health risk due to higher breathing rate and proximity to the vehicular exhaust. In this paper we present estimates of the exposure of a cyclist to particles of various size fractions including ultrafine particles (UFP) in the town of Mol (Flanders, Belgium). The results indicate relatively higher UFP concentration exposure during morning office hours and moderate UFP levels during afternoon. The major sources of UFP and PM(10) were identified, which are vehicular emission and construction activities, respectively. We also present a dust mapping technique which can be a useful tool for town planners and local policy makers.

Reduced Ultrafine Particle Concentration in Urban Air: Changes in Nucleation and Anthropogenic Emissions.

PubMed

Saha, Provat K; Robinson, Ellis S; Shah, Rishabh U; Zimmerman, Naomi; Apte, Joshua S; Robinson, Allen L; Presto, Albert A

2018-06-19

Nucleation is an important source of ambient ultrafine particles (UFP). We present observational evidence of the changes in the frequency and intensity of nucleation events in urban air by analyzing long-term particle size distribution measurements at an urban background site in Pittsburgh, Pennsylvania during 2001-2002 and 2016-2017. We find that both frequency and intensity of nucleation events have been reduced by 40-50% over the past 15 years, resulting in a 70% reduction in UFP concentrations from nucleation. On average, the particle growth rates are 30% slower than 15 years ago. We attribute these changes to dramatic reductions in SO 2 (more than 90%) and other pollutant concentrations. Overall, UFP concentrations in Pittsburgh have been reduced by ∼48% in the past 15 years, with a ∼70% reduction in nucleation, ∼27% in weekday local sources (e.g., weekday traffic), and 49% in the regional background. Our results highlight that a reduction in anthropogenic emissions can considerably reduce nucleation events and UFP concentrations in a polluted urban environment.

[Health effects of ambient ultrafine particles--the project UFIREG].

PubMed

Dostál, Miroslav; Pastorková, Anna; Lanzinger, Stefanie; Schneider, Alexandra; Bastian, Susanne; Senghaas, Monika; Erzen, Ziva; Novák, Jiří; Kolodnitska, Teťana; Šrám, Radim J; Peters, Annette

2015-01-01

The project "Ultrafine particles--an evidence based contribution to the development of regional and European environmental and health policy" (UFIREG) started in July 2011 and ended in December 2014. It was implemented through the Central Europe Programme and co-financed by the European Regional Development Fund. Five cities in four Central European countries participated in the study: Augsburg (Germany), Chernivtsi (Ukraine), Dresden (Germany), Ljubljana (Slovenia) and Prague (Czech Republic). The aim of the UFIREG project was to improve the knowledge base on possible health effects of ambient ultrafine particles (UFP) and to raise overall awareness of environmental and health care authorities and the population. Epidemiological studies in the frame of the UFIREG project have assessed the short-term effects of UFP on human mortality and morbidity, especially in relation to cardiovascular and respiratory diseases. Official statistics were used to determine the association between air pollution concentration and daily (cause-specific: respiratory and cardiovascular) hospital admissions and mortality. Associations of UFP levels and health effects were analysed for each city by use of Poisson regression models adjusting for a number of confounding factors. Results on morbidity and mortality effects of UFP were heterogeneous across the five European cities investigated. Overall, an increase in respiratory hospital admissions and mortality could be detected for increases in UFP concentrations. Results on cardiovascular health were less conclusive. Further multi-centre studies such as UFIREG are needed preferably investigating several years in order to produce powerful results.

Effects of ultrafine particles on the allergic inflammation in the lung of asthmatics: results of a double-blinded randomized cross-over clinical pilot study

PubMed Central

2014-01-01

Background Epidemiological and experimental studies suggest that exposure to ultrafine particles (UFP) might aggravate the allergic inflammation of the lung in asthmatics. Methods We exposed 12 allergic asthmatics in two subgroups in a double-blinded randomized cross-over design, first to freshly generated ultrafine carbon particles (64 μg/m3; 6.1 ± 0.4 × 105 particles/cm3 for 2 h) and then to filtered air or vice versa with a 28-day recovery period in-between. Eighteen hours after each exposure, grass pollen was instilled into a lung lobe via bronchoscopy. Another 24 hours later, inflammatory cells were collected by means of bronchoalveolar lavage (BAL). (Trial registration: NCT00527462) Results For the entire study group, inhalation of UFP by itself had no significant effect on the allergen induced inflammatory response measured with total cell count as compared to exposure with filtered air (p = 0.188). However, the subgroup of subjects, which inhaled UFP during the first exposure, exhibited a significant increase in total BAL cells (p = 0.021), eosinophils (p = 0.031) and monocytes (p = 0.013) after filtered air exposure and subsequent allergen challenge 28 days later. Additionally, the potential of BAL cells to generate oxidant radicals was significantly elevated at that time point. The subgroup that was exposed first to filtered air and 28 days later to UFP did not reveal differences between sessions. Conclusions Our data demonstrate that pre-allergen exposure to UFP had no acute effect on the allergic inflammation. However, the subgroup analysis lead to the speculation that inhaled UFP particles might have a long-term effect on the inflammatory course in asthmatic patients. This should be reconfirmed in further studies with an appropriate study design and sufficient number of subjects. PMID:25204642

A case study of exposure to ultrafine particles from secondhand tobacco smoke in an automobile.

PubMed

Liu, S; Zhu, Y

2010-10-01

Secondhand tobacco smoke (SHS) in enclosed spaces is a major source of potentially harmful airborne particles. To quantify exposure to ultrafine particles (UFP) because of SHS and to investigate the interaction between pollutants from SHS and vehicular emissions, number concentration and size distribution of UFP and other air pollutants (CO, CO(2) , and PM(2.5)) were measured inside a moving vehicle under five different ventilation conditions. A major interstate freeway with a speed limit of 60 mph and an urban roadway with a speed limit of 30 mph were selected to represent typical urban routes. In a typical 30-min commute on urban roadways, the SHS of one cigarette exposed passengers to approximately 10 times the UFP and 120 times the PM(2.5) of ambient air. The most effective solution to protect passengers from SHS exposure is to abstain from smoking in the vehicle. Opening a window is an effective method for decreasing pollutant exposures on most urban roadways. However, under road conditions with high UFP concentrations, such as tunnels or busy freeways with high proportion of heavy-duty diesel trucks (such as the 710 Freeway in Los Angeles, CA, USA), opening a window is not a viable method to reduce UFPs. Time budget studies show that Americans spend, on average, more than 60 min each day in enclosed vehicles. Smoking inside vehicles can expose the driver and other passengers to high levels of pollutants. Thus, an understanding of the variations and interactions of secondhand tobacco smoke (SHS) and vehicular emissions under realistic driving conditions is necessary. Results of this study indicated that high ventilation rates can effectively dilute ultrafine particles (UFP) inside moving vehicles on urban routes. However, driving with open windows and an increased air exchange rate (AER) are not recommended on tunnels and heavily travelled freeways.

Multi-metric measurement of personal exposure to ultrafine particles in selected urban microenvironments

NASA Astrophysics Data System (ADS)

Spinazzè, Andrea; Cattaneo, Andrea; Scocca, Damiano R.; Bonzini, Matteo; Cavallo, Domenico M.

2015-06-01

At the beginning of the study, our hypothesis was that visiting certain microenvironments (MEs) is one of the most important determinants of personal exposure to ultrafine particles (UFP) and that moving between microenvironments significantly differentiates exposure. The overall aim of this study is to perform relevant exposure measurements to extend our knowledge on environmental exposure to UFP in urban environments. The UFP concentrations in different urban MEs were measured by personal monitoring in repeated sampling campaigns along a fixed route. The measurement runs were performed on one-week periods and at different times of day (AM: 08.00-10.30; PM: 16.00-18.30) and repeated in different periods of the year (winter, spring, summer, and autumn) for a total of 56 runs (>110 h). Measurements included on-line monitoring of the UFP particle number concentration (PNC), mean diameter (mean-d) and lung-deposited surface-area (LDSA). Additionally, the PNC, particle mass concentration (PMC) profiles for quasi-ultrafine particles (QUFP; PM0.25) were estimated. A significant seasonal difference in the PNC and PMC, mean diameter and surface area was observed as well as between different times of the day and days of the week. In addition, differences in the UFP concentrations were also found in each ME, and there were specific mean-diameter and surface area concentrations. In general, the mean particle diameters showed an inverse relationship with the PNC, while the LDSA had the opposite behaviour. Appreciable differences among all MEs and monitoring periods were observed; the concentration patterns and variations seemed related to the typical sources of urban pollutants (traffic), proximity to sources and time of day. The highest exposures were observed for walking or biking along high-trafficked routes and while using public buses. The UFP exposure levels in modern cars, equipped with high-efficiency filters and in air recirculation mode, were significantly lower.

Robustness of intra urban land-use regression models for ultrafine particles and black carbon based on mobile monitoring.

PubMed

Kerckhoffs, Jules; Hoek, Gerard; Vlaanderen, Jelle; van Nunen, Erik; Messier, Kyle; Brunekreef, Bert; Gulliver, John; Vermeulen, Roel

2017-11-01

Land-use regression (LUR) models for ultrafine particles (UFP) and Black Carbon (BC) in urban areas have been developed using short-term stationary monitoring or mobile platforms in order to capture the high variability of these pollutants. However, little is known about the comparability of predictions of mobile and short-term stationary models and especially the validity of these models for assessing residential exposures and the robustness of model predictions developed in different campaigns. We used an electric car to collect mobile measurements (n = 5236 unique road segments) and short-term stationary measurements (3 × 30min, n = 240) of UFP and BC in three Dutch cities (Amsterdam, Utrecht, Maastricht) in 2014-2015. Predictions of LUR models based on mobile measurements were compared to (i) measured concentrations at the short-term stationary sites, (ii) LUR model predictions based on short-term stationary measurements at 1500 random addresses in the three cities, (iii) externally obtained home outdoor measurements (3 × 24h samples; n = 42) and (iv) predictions of a LUR model developed based upon a 2013 mobile campaign in two cities (Amsterdam, Rotterdam). Despite the poor model R 2 of 15%, the ability of mobile UFP models to predict measurements with longer averaging time increased substantially from 36% for short-term stationary measurements to 57% for home outdoor measurements. In contrast, the mobile BC model only predicted 14% of the variation in the short-term stationary sites and also 14% of the home outdoor sites. Models based upon mobile and short-term stationary monitoring provided fairly high correlated predictions of UFP concentrations at 1500 randomly selected addresses in the three Dutch cities (R 2 = 0.64). We found higher UFP predictions (of about 30%) based on mobile models opposed to short-term model predictions and home outdoor measurements with no clear geospatial patterns. The mobile model for UFP was stable over different settings as the model predicted concentration levels highly correlated to predictions made by a previously developed LUR model with another spatial extent and in a different year at the 1500 random addresses (R 2 = 0.80). In conclusion, mobile monitoring provided robust LUR models for UFP, valid to use in epidemiological studies. Copyright © 2017 Elsevier Inc. All rights reserved.

Indoor particulate pollution in fitness centres with emphasis on ultrafine particles.

PubMed

Slezakova, Klara; Peixoto, Cátia; Oliveira, Marta; Delerue-Matos, Cristina; Pereira, Maria do Carmo; Morais, Simone

2018-02-01

Fitness centres (FC) represent a unique indoor microenvironment. Exercising on regular basis provides countless health benefits and improves overall well-being, but if these facilities have poor indoor air quality, the respective exercisers might be subjected to some adverse risks. Considering the limited existent data, this work aimed to evaluate particulate pollution (PM 10, PM 2.5 , and ultrafine particles - UFP) in indoor air of FC and to estimate the respective risks for occupants (both staff and exercising subjects). Sampling was conducted during 40 consecutive days of May-June 2014 in general fitness areas, studios and classrooms (for group activities) of four different fitness centres (FC1-FC4) situated within Oporto metropolitan area, Portugal. The results showed that across the four FC, PM 10 ranged between 5 and 1080 μg m -3 with median concentrations (15-43 μg m -3 ) fulfilling the limit (50 μg m -3 ) of Portuguese legislation in all FC. PM 2.5 (medians 5-37 μg m -3 ; range 5-777 μg m -3 ) exceeded thresholds of 25 μg m -3 at some FC, indicating potential risks for the respective occupants; naturally ventilated FC exhibited significantly higher PM ranges (p < 0.05). Similarly, UFPs (range 0.5-88.6 × 10 3 # cm -3 ) median concentrations were higher (2-3 times) at FC without controlled ventilation systems. UFP were approximately twice higher (p < 0.05) during the occupied periods (mean of 9.7 × 10 3 vs. 4.8 × 10 3 # cm -3 ) with larger temporal variations of UFP levels observed in general fitness areas than in classrooms and studios. Cardio activities (conducted in studios and classrooms) led to approximately twice the UFPs intakes than other types of exercising. These results indicate that even short-term physical activity (or more specifically its intensity) might strongly influence the daily inhalation dose. Finally, women exhibited 1.2 times higher UFPs intake than men thus suggesting the need for future gender-specific studies assessing UFP exposure. Copyright © 2017 Elsevier Ltd. All rights reserved.

Assessing the Cytotoxicity of Black Carbon As A Model for Ultrafine Anthropogenic Aerosol Across Human and Murine Cells: A Chronic Exposure Model of Nanosized Particulate Matter

NASA Astrophysics Data System (ADS)

Salinas, E.

2015-12-01

Combustion-derived nanomaterials or ultrafine (<1 μm) atmospheric aerosols are primarily products of anthropogenic activities, such as the burning of fossil fuels. Ultrafine particles (UFPs) can absorb other noxious pollutants including volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), toxic organic compounds, and heavy metals. The combination of high population density, meteorological conditions, and industrial productivity brings high levels of air pollution to the metropolitan area of El Paso, Texas, USA/ Ciudad Juarez, Chihuahua, Mexico, comprising the Paso del Norte air basin. A study conducted by scientists from the Research Triangle Park in North Carolina, analyzed sites adjacent to heavy-traffic highways in El Paso and elucidated higher UFP concentrations in comparison to previously published work exploring pollution and adverse health effects in the basin. UFPs can penetrate deep into the alveolar sacs of the lung, reaching distant alveolar sacs and inducing a series of immune responses that are detrimental to the body: evidence suggests that UFPs can also cross the alveolar-blood barrier and potentially endanger the body's immune response. The physical properties of UFPs and the dynamics of local atmospheric and topographical conditions indicate that emissions of nanosized carbonaceous aerosols could pose significant threats to biological tissues upon inhalation by local residents of the Paso del Norte. This study utilizes Black Carbon (BC) as a model for environmental UFPs and its effects on the immunological response. An in vitro approach is used to measure the ability of BC to promote cell death upon long-term exposure. Human epithelial lung cells (A549), human peripheral-blood monocytes (THP-1), murine macrophages (RAW264.7), and murine epithelial lung cells (LA-4) were treated with BC and assessed for metabolic activity after chronic exposure utilizing three distinct and independent cell viability assays. The cell viability experiments included a chronic study at 7, 10, and 14 days of UFP exposure at six different concentrations of BC: 100μM, 300μM, 600μM, 1,250μM, 2,500μM, and 5,000μM conducting the Trypan Blue (TB) Exclusion Assay, Calcein-AM Viability Assay, and CellTiter-Glo Viability Assay.

Contribution of various microenvironments to the daily personal exposure to ultrafine particles: Personal monitoring coupled with GPS tracking

NASA Astrophysics Data System (ADS)

Bekö, Gabriel; Kjeldsen, Birthe Uldahl; Olsen, Yulia; Schipperijn, Jasper; Wierzbicka, Aneta; Karottki, Dorina Gabriela; Toftum, Jørn; Loft, Steffen; Clausen, Geo

2015-06-01

Exposure to ultrafine particles (UFP) may have adverse health effects. Central monitoring stations do not represent the personal exposure to UFP accurately. Few studies have previously focused on personal exposure to UFP. Sixty non-smoking residents living in Copenhagen, Denmark were asked to carry a backpack equipped with a portable monitor, continuously recording particle number concentrations (PN), in order to measure the real-time individual exposure over a period of ˜48 h. A GPS logger was carried along with the particle monitor and allowed us to estimate the contribution of UFP exposure occurring in various microenvironments (residence, during active and passive transport, other indoor and outdoor environments) to the total daily exposure. On average, the fractional contribution of each microenvironment to the daily integrated personal exposure roughly corresponded to the fractions of the day the subjects spent in each microenvironment. The home environment accounted for 50% of the daily personal exposure. Indoor environments other than home or vehicles contributed with ˜40%. The highest median UFP concentration was obtained during passive transport (vehicles). However, being in transit or outdoors contributed 5% or less to the daily exposure. Additionally, the subjects recorded in a diary the periods when they were at home. With this approach, 66% of the total daily exposure was attributable to the home environment. The subjects spent 28% more time at home according to the diary, compared to the GPS. These results may indicate limitations of using diaries, but also possible inaccuracy and miss-classification in the GPS data.

Personal exposure to particulate matter in commuters using different transport modes (bus, bicycle, car and subway) in an assigned route in downtown Santiago, Chile.

PubMed

Suárez, Liliana; Mesías, Stephanie; Iglesias, Verónica; Silva, Claudio; Cáceres, Dante D; Ruiz-Rudolph, Pablo

2014-05-01

The objective of this study was to compare personal exposure to particulate matter (fine and ultrafine particles) in commuters using different transport modes (bicycle, bus, car and subway) in a busy, assigned route in downtown Santiago, Chile. Volunteers carrying personal samplers completed scheduled commutes during the morning rush hours, while central site measurements were conducted in parallel. A total of 137 valid commutes were assessed. The impact of central site, traffic and other variables was explored with regression models. PM2.5 personal concentrations were equal to or slightly above central site measurements, while UFP personal concentrations were above them. Regression models showed impacts of both background levels and traffic emissions on personal PM2.5 and UFP exposure. Traffic impacts varied with transport modes. Estimates of traffic impacts on personal PM2.5 exposure were 2.0, 13.0, 16.9 and 17.5 μg m(-3), for car, bicycle, subway and bus, respectively; while for UFP exposure were 8400, 16 200, 25 600 and 30 100 counts per cm(3), for subway, car, bicycle and bus, respectively. After controlling the central site and transport mode, higher temperatures increased PM2.5 exposure and decreased UFP ones, while the wind direction affected UFP personal exposure. In conclusion, we found significant impacts of both central site background measurements and traffic emissions on personal exposure of volunteer commuters in an assigned route in Santiago, with impacts varying with transport modes.

Physical stability of R-(+)-Limonene emulsions stabilized by Ulva fasciata algae polysaccharide.

PubMed

Shao, Ping; Ma, Huiling; Qiu, Qiang; Jing, Weiping

2016-11-01

The physical stability of R-(+)-Limonene emulsions stabilized by Ulva fasciata polysaccharide (UFP) was investigated in this study. Emulsion physical stability was evaluated under different polysaccharide concentrations (1%-5%, wt/wt) and pH values (3.0-11.0). The stability of R-(+)-Limonene emulsions was demonstrated by droplet size distribution, rheological properties, zeta potential and visual phase separation. R-(+)-Limonene emulsions displayed monomodal droplet size distributions, high absolute values of zeta potential and good storage stability when 3% (wt/wt) UFP was used. The rheological properties and stability of R-(+)-Limonene emulsions appeared to be dependent on polysaccharide concentration. The emulsion stability was impacted by pH. Higher zeta potential (-52.6mV) and smaller mean droplet diameter (2.45μm) were achieved in neutral liquid environment (pH 7.0). Extreme acidity caused the flocculation of emulsions, which was manifested as phase separation, while emulsions were quite stable in an alkaline environment. Through comparing the stabilities of emulsions stabilized by different emulsifiers (i.e. UFP, GA and Gelatin), the result suggested that UFP was the best emulsifying agent among them. Copyright © 2016 Elsevier B.V. All rights reserved.

Exposure to ultrafine particles and black carbon in diesel-powered commuter trains

NASA Astrophysics Data System (ADS)

Jeong, Cheol-Heon; Traub, Alison; Evans, Greg J.

2017-04-01

Ultrafine particle (UFP), black carbon (BC) and lung deposited surface area (LDSA) concentrations measured during 43 trips on diesel-powered commuter trains revealed elevated exposures under some conditions. When the passenger coaches were pulled by a locomotive, the geometric mean concentrations of UFP, LDSA, and BC were 18, 10, and 6 times higher than the exposure levels when the locomotive pushed the coaches, respectively. In addition, UFP, LDSA, and BC concentrations in pull-trains were 5, 3, and 4 times higher than concentrations measured while walking on city sidewalks, respectively. Exposure to these pollutants was most elevated in the coach located closest to the locomotive: geometric means were 126,000 # cm-3 for UFP, 249 μm2 cm-3 for LDSA, and 17,800 ng m-3 of BC; these concentrations are much higher than those previously reported for other modes of public transportation. Markedly high levels of diesel exhaust are present in passenger trains powered by diesel locomotives operated in pull-mode. Thus, it is recommended that immediate steps be taken to evaluate, and where needed, mitigate exposure in diesel-powered passenger trains, both commuter and inter-city.

The association between the incidence of postmenopausal breast cancer and concentrations at street-level of nitrogen dioxide and ultrafine particles.

PubMed

Goldberg, Mark S; Labrèche, France; Weichenthal, Scott; Lavigne, Eric; Valois, Marie-France; Hatzopoulou, Marianne; Van Ryswyk, Keith; Shekarrizfard, Maryam; Villeneuve, Paul J; Crouse, Daniel; Parent, Marie-Élise

2017-10-01

There is scant information as to whether traffic-related air pollution is associated with the incidence of breast cancer. Nitrogen dioxide (NO 2 ) and ultrafine particles (UFPs, <0.1µm), are two pollutants that capture intra-urban variations in traffic-related air pollution and may also be associated with incidence. We conducted a population-based, case-control study of street-level concentrations of NO 2 and UFPs and incident postmenopausal breast cancer in Montreal, Canada. Incident cases were identified between 2008 and 2011 from all but one hospital that treated breast cancer in the Montreal area. Population controls were identified from provincial electoral lists of Montreal residents and frequency-matched to cases using 5-year age groups. Concentrations of NO 2 and UFPs were estimated using two separate land-use regression models. Exposures were assigned to residential locations at the time of recruitment, and we identified residential histories of women who had lived in these residences for 10 years or more. Odds ratios (OR) and 95% confidence intervals (CI) were estimated using logistic regression models adjusting for individual-level and ecological covariates. We assessed the functional form of NO 2 and UFP exposures using natural cubic splines. We found that the functional form of the response functions between incident postmenopausal breast cancer and concentrations of NO 2 and UFPs were consistent with linearity. For NO 2 , we found increasing risks of breast cancer for all subjects combined and stronger associations when analyses were restricted to those women who had lived at their current address for 10 years or more. Specifically, the OR, adjusted for personal covariates, per increase in the interquartile range (IQR=3.75 ppb) of NO 2 was 1.08 (95%CI: 0.92-1.27). For women living in their homes for 10 years or more, the adjusted OR was 1.17 (95%CI: 0.93-1.46; IQR=3.84 ppb); for those not living at that home 10 years before the study, it was 0.93 (95%CI: 0.64, 1.36; IQR=3.65 ppb). For UFPs, the ORs were lower than for NO 2 , with little evidence of association in any of the models or sub-analyses and little variability in the ORs (about 1.02 for an IQR of ~3500cm -3 ). On the other hand, we found higher ORs amongst cases with positive oestrogen and progesterone receptor status; namely for NO 2 , the OR was 1.13 (95%CI: 0.94-1.35) and for UFPs it was 1.05 (95%CI: 0.96-1.14). Our findings suggest that exposure to ambient NO 2 and UFPs may increase the risk of incident postmenopausal breast cancer especially amongst cases with positive oestrogen and progesterone receptor status. Copyright © 2017. Published by Elsevier Inc.

On testing of the photometer-polarimeter UVP layout using a telescope on Earth's surface

NASA Astrophysics Data System (ADS)

Nevodovskyi, P. V.; Vidmachenko, A. P.; Morozhenko, O. V.; Zbrutskyi, O.; Ivakhiv, O. V.

2016-08-01

One of the causes of climate change (changing of concentration of stratospheric ozone) - is variations due to aerosol optical thickness in the upper layers of Earth's atmosphere. To solve the problem is necessary to make a space experiment to receive polarization observational data. Their analysis will: determine the value of the real part of the refractive index, the size of the stratospheric aerosol, optical thickness of the stratospheric aerosol layer, investigate aerosol's layer horizontal structure and its changes over time. Main Astronomical Observatory of NAS of Ukraine jointly with the National Technical University of Ukraine "KPI" and National University "Lviv Polytechnic" for a long time working on the design of polarimeter to study the stratospheric layer of the Earth from board of artificial satellites. During this time accumulated a great experience in such work, and created a layout of compact board ultraviolet polarimeter UFP [1-4]. For testing of ground variant of layout of UFP, it is installed on the telescope AZT-2 of the Main Astronomical Observatory NAS of Ukraine (Kyiv). Using it we plan to investigate the possibility of determining the degree of polarization of the twilight glow of Earth's atmosphere, and implementation of this technique in the development of space experiment on investigation of the stratospheric aerosol from space. For this purpose we develop a special set of equipment that will adapt the layout for working of UFP with telescope AZT-2, and carry out the above mentioned work (see. in [5-7]). References. 1. P. Nevodovskyi, O. Morozhenko, A. Vidmachenko, O. Ivakhiv, M. Geraimchuk, O. Zbrutskyi. Tiny Ultraviolet Polarimeter for Earth Stratosphere from Space Investigation // Proceedings of 8th IEEE International Conference on Intelligent Data Acquisition and Advanced Computing Systems: Technology and Applications (IDAACS'2015). 24-26 September 2015, Proceedings. Warsaw, Poland. Vol.81, p. 28-32. 2. Nevodovsksiy P. V., Morozhenko A. V. Studies of stratospheric ozone layer from near-earth orbit utilizing ultraviolet polarimeter // Acta Astronautica. 2009, vol. 64, no 1, p. 54-58. 3. Nevodovskij P. V. Kvantakons and optimization of their parameters for astronomical observations Kinematika i Fizika Nebesnykh Tel. 2001, vol. 17, no. 3, p. 279-288. 4. A. P. Vid'machenko, P. V. Nevodovsky. A cooled photomultiplier with an InGaAs photocathode developed for the spectropolarimetry observations // Kinematika i Fizika Nebesnykh Tel. 2000. Suppl. 3, p. 283-285. 5. Morozhenko A. V., Vidmachenko A. P., Nevodovskiy P. V., Kostogryz N. M. On the efficiency of polarization measurements while studying aerosols in the terrestrial atmosphere // Kinematics and Physics of Celestial Bodies. 2014, vol. 30, no. 1, p. 11-21. 6. A.V. Morozhenko, A.P. Vidmachenko, P.V. Nevodovskyi. Aerosol in the upper layer of earth's atmosphere // Kinematics and Physics of Celestial Bodies. 2013, vol. 29, no. 5, p. 243-246. 7. Morozhenko A.V. Polarimetry of twilight sky and stratospheric aerosol // Kinematics and Physics of Celestial Bodies. 2010, vol. 26, no. 1, p. 36-38.

Short-term effects of ultrafine particles on daily mortality by primary vehicle exhaust versus secondary origin in three Spanish cities.

PubMed

Tobías, Aurelio; Rivas, Ioar; Reche, Cristina; Alastuey, Andrés; Rodríguez, Sergio; Fernández-Camacho, Rocío; Sánchez de la Campa, Ana M; de la Rosa, Jesús; Sunyer, Jordi; Querol, Xavier

2018-02-01

Evidence on the short-term effects of ultrafine particles (with diameter<100nm, UFP) on health is still inconsistent. New particles in ambient urban air are the result of direct emissions and also the formation of secondary UFP from gaseous precursors. We segregated UFP into these two components and investigated their impact on daily mortality in three Spanish cities affected by different sources of air pollution. We separated the UFP using a method based on the high correlation between black carbon (BC) and particle number concentration (N). The first component accounts for aerosol constituents emitted by vehicle exhaust (N1) and the second for the photochemical new particle formation enhancements (N2). We applied city-specific Poisson regression models, adjusting for long-term trends, temperature and population dynamics. Mean BC levels were higher in Barcelona and Tenerife (1.8 and 1.2μg·m -3 , respectively) than in Huelva (0.8μg·m -3 ). While mean UFP concentrations were similar in the three cities, from which N1 was 40% in Barcelona, 46% in Santa Cruz de Tenerife, and 27% in Huelva. We observed an association with N1 and daily mortality in Barcelona, by increasing approximately 1.5% between lags 0 and 2, per an interquartile increase (IQR) of 3277cm -3 , but not with N2. A similar pattern was found in Santa Cruz de Tenerife, although none of the associations were significant. Conversely, in the industrial city of Huelva mortality was associated with N2 at lag 0, by increasing 3.9% per an IQR of 12,032·cm -3 . The pattern and origin of UFP determines their short-term effect on human health. BC is possibly the better parameter to evaluate the health effects of particulate vehicle exhaust emissions, although in areas influenced by domestic solid fuel combustion this should also be taken into account. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

A land use regression model for ambient ultrafine particles in Montreal, Canada: A comparison of linear regression and a machine learning approach.

PubMed

Weichenthal, Scott; Ryswyk, Keith Van; Goldstein, Alon; Bagg, Scott; Shekkarizfard, Maryam; Hatzopoulou, Marianne

2016-04-01

Existing evidence suggests that ambient ultrafine particles (UFPs) (<0.1µm) may contribute to acute cardiorespiratory morbidity. However, few studies have examined the long-term health effects of these pollutants owing in part to a need for exposure surfaces that can be applied in large population-based studies. To address this need, we developed a land use regression model for UFPs in Montreal, Canada using mobile monitoring data collected from 414 road segments during the summer and winter months between 2011 and 2012. Two different approaches were examined for model development including standard multivariable linear regression and a machine learning approach (kernel-based regularized least squares (KRLS)) that learns the functional form of covariate impacts on ambient UFP concentrations from the data. The final models included parameters for population density, ambient temperature and wind speed, land use parameters (park space and open space), length of local roads and rail, and estimated annual average NOx emissions from traffic. The final multivariable linear regression model explained 62% of the spatial variation in ambient UFP concentrations whereas the KRLS model explained 79% of the variance. The KRLS model performed slightly better than the linear regression model when evaluated using an external dataset (R(2)=0.58 vs. 0.55) or a cross-validation procedure (R(2)=0.67 vs. 0.60). In general, our findings suggest that the KRLS approach may offer modest improvements in predictive performance compared to standard multivariable linear regression models used to estimate spatial variations in ambient UFPs. However, differences in predictive performance were not statistically significant when evaluated using the cross-validation procedure. Crown Copyright © 2015. Published by Elsevier Inc. All rights reserved.

Exposure to ultrafine particles and PM 2.5 in four Sydney transport modes

NASA Astrophysics Data System (ADS)

Knibbs, Luke D.; de Dear, Richard J.

2010-08-01

Concentrations of ultrafine (<0.1 μm) particles (UFPs) and PM 2.5 (<2.5 μm) were measured whilst commuting along a similar route by train, bus, ferry and automobile in Sydney, Australia. One trip on each transport mode was undertaken during both morning and evening peak hours throughout a working week, for a total of 40 trips. Analyses comprised one-way ANOVA to compare overall (i.e. all trips combined) geometric mean concentrations of both particle fractions measured across transport modes, and assessment of both the correlation between wind speed and individual trip means of UFPs and PM 2.5, and the correlation between the two particle fractions. Overall geometric mean concentrations of UFPs and PM 2.5 ranged from 2.8 (train) to 8.4 (bus) × 10 4 particles cm -3 and 22.6 (automobile) to 29.6 (bus) μg m -3, respectively, and a statistically significant difference ( p < 0.001) between modes was found for both particle fractions. Individual trip geometric mean concentrations were between 9.7 × 10 3 (train) and 2.2 × 10 5 (bus) particles cm -3 and 9.5 (train) to 78.7 (train) μg m -3. Estimated commuter exposures were variable, and the highest return trip mean PM 2.5 exposure occurred in the ferry mode, whilst the highest UFP exposure occurred during bus trips. The correlation between fractions was generally poor, and in keeping with the duality of particle mass and number emissions in vehicle-dominated urban areas. Wind speed was negatively correlated with, and a generally poor determinant of, UFP and PM 2.5 concentrations, suggesting a more significant role for other factors in determining commuter exposure.

Chronic Obstructive Pulmonary Disease-Derived Circulating Cells Release IL-18 and IL-33 under Ultrafine Particulate Matter Exposure in a Caspase-1/8-Independent Manner

PubMed Central

De Falco, Gianluigi; Colarusso, Chiara; Terlizzi, Michela; Popolo, Ada; Pecoraro, Michela; Commodo, Mario; Minutolo, Patrizia; Sirignano, Mariano; D’Anna, Andrea; Aquino, Rita P.; Pinto, Aldo; Molino, Antonio; Sorrentino, Rosalinda

2017-01-01

Chronic obstructive pulmonary disease (COPD) is considered the fourth-leading causes of death worldwide; COPD is caused by inhalation of noxious indoor and outdoor particles, especially cigarette smoke that represents the first risk factor for this respiratory disorder. To mimic the effects of particulate matter on COPD, we isolated peripheral blood mononuclear cells (PBMCs) and treated them with combustion-generated ultrafine particles (UFPs) obtained from two different fuel mixtures, namely, pure ethylene and a mixture of ethylene and dimethylfuran (the latter mimicking the combustion of biofuels). UFPs were separated in two fractions: (1) sub-10 nm particles, named nano organic carbon (NOC) particles and (2) primarily soot particles of 20–40 nm and their agglomerates (200 nm). We found that both NOC and soot UFPs induced the release of IL-18 and IL-33 from unstable/exacerbated COPD-derived PBMCs. This effect was associated with higher levels of mitochondrial dysfunction and derived reactive oxygen species, which were higher in PBMCs from unstable COPD patients after combustion-generated UFP exposure. Moreover, lower mRNA expression of the repairing enzyme OGG1 was associated with the higher levels of 8-OH-dG compared with non-smoker and smokers. It was interesting that IL-18 and IL-33 release from PBMCs of unstable COPD patients was not NOD-like receptor 3/caspase-1 or caspase-8-dependent, but rather correlated to caspase-4 release. This effect was not evident in stable COPD-derived PBMCs. Our data suggest that combustion-generated UFPs induce the release of caspase-4-dependent inflammasome from PBMCs of COPD patients compared with healthy subjects, shedding new light into the biology of this key complex in COPD. PMID:29123531

Ultrafine particle concentrations and exposures in seven residences in northern California.

PubMed

Bhangar, S; Mullen, N A; Hering, S V; Kreisberg, N M; Nazaroff, W W

2011-04-01

Human exposures to ultrafine particles (UFP) are poorly characterized given the potential associated health risks. Residences are important sites of exposure. To characterize residential exposures to UFP in some circumstances and to investigate governing factors, seven single-family houses in California were studied during 2007-2009. During multiday periods, time-resolved particle number concentrations were monitored indoors and outdoors and information was acquired concerning occupancy, source-related activities, and building operation. On average, occupants were home for 70% of their time. The geometric mean time-average residential exposure concentration for 21 study subjects was 14,500 particles per cm(3) (GSD = 1.8; arithmetic mean ± standard deviation = 17,000 ± 10,300 particles per cm(3)). The average contribution to residential exposures from indoor episodic sources was 150% of the contribution from particles of outdoor origin. Unvented natural-gas pilot lights contributed up to 19% to exposure for the two households where present. Episodic indoor source activities, most notably cooking, caused the highest peak exposures and most of the variation in exposure among houses. Owing to the importance of indoor sources and variations in the infiltration factor, residential exposure to UFP cannot be characterized by ambient measurements alone. Indoor and outdoor sources each contribute to residential ultrafine particle (UFP) concentrations and exposures. Under the conditions investigated, peak exposure concentrations indoors were associated with cooking, using candles, or the use of a furnace. Active particle removal systems can mitigate exposure by reducing the persistence of particles indoors. Eliminating the use of unvented gas pilot lights on cooking appliances could also be beneficial. The study results indicate that characterization of human exposure to UFP, an air pollutant of emerging public health concern, cannot be accomplished without a good understanding of conditions inside residences. © 2010 John Wiley & Sons A/S.

Particulate Matter Exposure in a Police Station Located near a Highway.

PubMed

Chen, Yu-Cheng; Hsu, Chin-Kai; Wang, Chia C; Tsai, Perng-Jy; Wang, Chun-Yuan; Chen, Mei-Ru; Lin, Ming-Yeng

2015-11-13

People living or working near roadways have experienced an increase in cardiovascular or respiratory diseases due to vehicle emissions. Very few studies have focused on the PM exposure of highway police officers, particularly for the number concentration and size distribution of ultrafine particles (UFP). This study evaluated exposure concentrations of particulate matter (PM) in the Sinying police station near a highway located in Tainan, Taiwan, under different traffic volumes, traffic types, and shift times. We focused on periods when the wind blew from the highway toward the police station and when the wind speed was greater than or equal to 0.5 m/s. PM2.5, UFP, and PM-PAHs concentrations in the police station and an upwind reference station were measured. Results indicate that PM2.5, UFP, and PM-PAHs concentrations in the police station can be on average 1.13, 2.17, and 5.81 times more than the upwind reference station concentrations, respectively. The highest exposure level for PM2.5 and UFP was observed during the 12:00 PM-4:00 PM shift while the highest PAHs concentration was found in the 4:00 AM-8:00 AM shift. Thus, special attention needs to be given to protect police officers from exposure to high PM concentration.

Particulate Matter Exposure in a Police Station Located near a Highway

PubMed Central

Chen, Yu-Cheng; Hsu, Chin-Kai; Wang, Chia C.; Tsai, Perng-Jy; Wang, Chun-Yuan; Chen, Mei-Ru; Lin, Ming-Yeng

2015-01-01

People living or working near roadways have experienced an increase in cardiovascular or respiratory diseases due to vehicle emissions. Very few studies have focused on the PM exposure of highway police officers, particularly for the number concentration and size distribution of ultrafine particles (UFP). This study evaluated exposure concentrations of particulate matter (PM) in the Sinying police station near a highway located in Tainan, Taiwan, under different traffic volumes, traffic types, and shift times. We focused on periods when the wind blew from the highway toward the police station and when the wind speed was greater than or equal to 0.5 m/s. PM2.5, UFP, and PM-PAHs concentrations in the police station and an upwind reference station were measured. Results indicate that PM2.5, UFP, and PM-PAHs concentrations in the police station can be on average 1.13, 2.17, and 5.81 times more than the upwind reference station concentrations, respectively. The highest exposure level for PM2.5 and UFP was observed during the 12:00 PM–4:00 PM shift while the highest PAHs concentration was found in the 4:00 AM–8:00 AM shift. Thus, special attention needs to be given to protect police officers from exposure to high PM concentration. PMID:26580641

Impacts of freeway traffic conditions on in-vehicle exposure to ultrafine particulate matter

NASA Astrophysics Data System (ADS)

Bigazzi, Alexander Y.; Figliozzi, Miguel A.

2012-12-01

There is evidence of adverse health impacts from human exposure to traffic-related ultrafine particulate matter pollution. As more commuters are spending a significant portion of their daily routine inside vehicles, it is increasingly relevant to study exposure levels to harmful pollutants inside the vehicle microenvironment. This study is one of the first research efforts to combine detailed freeway traffic data (at 20 s intervals) and in-vehicle ultrafine particulate (UFP) exposure data under varying vehicle ventilation conditions. Results show that due to negative correlation between traffic speed and density, traffic states have a small but significant impact on in-vehicle UFP concentrations, highest in high traffic flow-high speed conditions or in high traffic density-low speed conditions. Vehicle cabin barrier effects are the primary determinant of in-vehicle exposure concentrations, providing 15% protection with the windows down, 47% protection with the windows up and the vent open, and 83-90% protection with the windows up and the vent closed (more with the air conditioning on). Unique results from this study include the dominance of ventilation over traffic effects on UFP and the non-linear relationships between traffic variables and UFP concentrations. The results of this research have important implications for exposure modeling and potential exposure mitigation strategies.

Ultrafine Particle Distribution and Chemical Composition Assessment during Military Operative Trainings

PubMed Central

Campagna, Marcello; Pilia, Ilaria; Marcias, Gabriele; Frattolillo, Andrea; Pili, Sergio; Bernabei, Manuele; d’Aloja, Ernesto; Cocco, Pierluigi; Buonanno, Giorgio

2017-01-01

(1) Background: The assessment of airborne particulate matter (PM) and ultrafine particles (UFPs) in battlefield scenarios is a topic of particular concern; (2) Methods: Size distribution, concentration, and chemical composition of UFPs during operative military training activities (target drone launches, ammunition blasting, and inert bomb impact) were investigated using an electric low-pressure impactor (ELPI+) and a scanning electron microscope (SEM), equipped with energy-dispersive spectroscopy (EDS); (3) Results: The median of UFPs, measured for all sampling periods and at variable distance from sources, was between 1.02 × 103 and 3.75 × 103 particles/cm3 for drone launches, between 3.32 × 103 and 15.4 × 103 particles/cm3 for the ammunition blasting and from 7.9 × 103 to 1.3 × 104 particles/cm3 for inert launches. Maximum peak concentrations, during emitting sources starting, were 75.5 × 106 and 17.9 × 106 particles/cm3, respectively. Particles from the drone launches were predominantly composed of silicon (Si), iron (Fe) and calcium (Ca), and those from the blasting campaigns by magnesium (Mg), sulphur (S), aluminum (Al), iron (Fe), barium (Ba) and silicon (Si); (4) Conclusions: The investigated sources produced UFPs with median values lower than other anthropogenic sources, and with a similar chemical composition. PMID:28556812

Outbreak of sudden cardiac deaths in a tire manufacturing facility: can it be caused by nanoparticles?

PubMed

Kim, Eun-A; Park, Jungsun; Kim, Kun-Hyung; Lee, Naroo; Kim, Dae-Seong; Kang, Seong-Kyu

2012-03-01

The purpose of this study was to review clinical characteristics and working environments of sudden cardiac death (SCD) cases associated with a tire manufacturer in Korea, and review possible occupational risk factors for cardiovascular disease including nanoparticles (ultrafine particles, UFPs). We reviewed (i) the clinical course of SCD cases and (ii) occupational and non-occupational risk factors including chemicals, the physical work environment, and job characteristics. Possible occupational factors were chemicals, UFPs of rubber fume, a hot environment, shift work, overworking, and noise exposure. The mean diameter of rubber fume (63-73 nm) was (larger than diesel exhaust [12 nm] and outdoor dust [50 nm]). The concentration of carbon disulfide, carbon monoxide and styrene were lower than the limit of detection. Five SCD cases were exposed to shift work and overworking. Most of the cases had several non-occupational factors such as hypertension, overweight and smoking. The diameter of rubber fume was larger than outdoor and the diesel exhaust, the most well known particulate having a causal relationship with cardiovascular disease. The possibility of a causal relation between UFPs of rubber fume and SCD was not supported in this study. However, it is necessary to continue studying the relationship between large sized UFPs and SCD.

Outbreak of Sudden Cardiac Deaths in a Tire Manufacturing Facility: Can It Be Caused by Nanoparticles?

PubMed Central

Kim, Eun-A; Kim, Kun-Hyung; Lee, Naroo; Kim, Dae-Seong; Kang, Seong-Kyu

2012-01-01

Objectives The purpose of this study was to review clinical characteristics and working environments of sudden cardiac death (SCD) cases associated with a tire manufacturer in Korea, and review possible occupational risk factors for cardiovascular disease including nanoparticles (ultrafine particles, UFPs). Methods We reviewed (i) the clinical course of SCD cases and (ii) occupational and non-occupational risk factors including chemicals, the physical work environment, and job characteristics. Results Possible occupational factors were chemicals, UFPs of rubber fume, a hot environment, shift work, overworking, and noise exposure. The mean diameter of rubber fume (63-73 nm) was (larger than diesel exhaust [12 nm] and outdoor dust [50 nm]). The concentration of carbon disulfide, carbon monoxide and styrene were lower than the limit of detection. Five SCD cases were exposed to shift work and overworking. Most of the cases had several non-occupational factors such as hypertension, overweight and smoking. Conclusion The diameter of rubber fume was larger than outdoor and the diesel exhaust, the most well known particulate having a causal relationship with cardiovascular disease. The possibility of a causal relation between UFPs of rubber fume and SCD was not supported in this study. However, it is necessary to continue studying the relationship between large sized UFPs and SCD. PMID:22953232

Personal exposure to airborne ultrafine particles in the urban area of Milan

NASA Astrophysics Data System (ADS)

Cattaneo, A.; Garramone, G.; Taronna, M.; Peruzzo, C.; Cavallo, D. M.

2009-02-01

The relevance of health effects related to ultrafine particles (UFPs; aerodynamic diameter < 100 nm) can be better evaluated using high-resolution strategies for measuring particle number concentrations. In this study, two different portable Condensation Particle Counters (CPCs) were used to measure personal exposure to UFPs in the central area of Milan for one week period during spring, with three sampling sessions per day. Experimental data were continuously collected along an established urban pathway, moving afoot or by different private and public means of transport. Correlation analysis between data measured by two CPCs was performed and general results showed a good agreement, especially at concentrations lower than 2×105 particles /cm3. UFPs measures were divided on the basis of crossed environments or micro-environments, days of the week and day time (hours). The highest measured mean concentrations and data variability were observed during walking time and moving on motorized vehicles (bus and car), indicating that the highest exposure to UFPs can be reached near motorized traffic. The lowest exposures were observed in green areas and in office microenvironments. An appreciable difference between working and non-working days was observed. Concentration patterns and variation by days of the week and time periods appears related to time trends in traffic intensity.

Comparisons of traffic-related ultrafine particle number concentrations measured in two urban areas by central, residential, and mobile monitoring

NASA Astrophysics Data System (ADS)

Simon, Matthew C.; Hudda, Neelakshi; Naumova, Elena N.; Levy, Jonathan I.; Brugge, Doug; Durant, John L.

2017-11-01

Traffic-related ultrafine particles (UFP; <100 nm diameter) are ubiquitous in urban air. While studies have shown that UFP are toxic, epidemiological evidence of health effects, which is needed to inform risk assessment at the population scale, is limited due to challenges of accurately estimating UFP exposures. Epidemiologic studies often use empirical models to estimate UFP exposures; however, the monitoring strategies upon which the models are based have varied between studies. Our study compares particle number concentrations (PNC; a proxy for UFP) measured by three different monitoring approaches (central-site, short-term residential-site, and mobile on-road monitoring) in two study areas in metropolitan Boston (MA, USA). Our objectives were to quantify ambient PNC differences between the three monitoring platforms, compare the temporal patterns and the spatial heterogeneity of PNC between the monitoring platforms, and identify factors that affect correlations across the platforms. We collected >12,000 h of measurements at the central sites, 1000 h of measurements at each of 20 residential sites in the two study areas, and >120 h of mobile measurements over the course of ∼1 year in each study area. Our results show differences between the monitoring strategies: mean 1 min PNC on-roads were higher (64,000 and 32,000 particles/cm3 in Boston and Chelsea, respectively) compared to central-site measurements (23,000 and 19,000 particles/cm3) and both were higher than at residences (14,000 and 15,000 particles/cm3). Temporal correlations and spatial heterogeneity also differed between the platforms. Temporal correlations were generally highest between central and residential sites, and lowest between central-site and on-road measurements. We observed the greatest spatial heterogeneity across monitoring platforms during the morning rush hours (06:00-09:00) and the lowest during the overnight hours (18:00-06:00). Longer averaging times (days and hours vs. minutes) increased temporal correlations (Pearson correlations were 0.69 and 0.60 vs. 0.39 in Boston; 0.71 and 0.61 vs. 0.45 in Chelsea) and reduced spatial heterogeneity (coefficients of divergence were 0.24 and 0.29 vs. 0.33 in Boston; 0.20 and 0.27 vs. 0.31 in Chelsea). Our results suggest that combining stationary and mobile monitoring may lead to improved characterization of UFP in urban areas.

Surface area-dependence of gas-particle interactions influences pulmonary and neuroinflammatory outcomes.

PubMed

Tyler, Christina R; Zychowski, Katherine E; Sanchez, Bethany N; Rivero, Valeria; Lucas, Selita; Herbert, Guy; Liu, June; Irshad, Hammad; McDonald, Jacob D; Bleske, Barry E; Campen, Matthew J

2016-12-01

Deleterious consequences of exposure to traffic emissions may derive from interactions between carbonaceous particulate matter (PM) and gaseous components in a manner that is dependent on the surface area or complexity of the particles. To determine the validity of this hypothesis, we examined pulmonary and neurological inflammatory outcomes in C57BL/6 and apolipoprotein E knockout (ApoE -/- ) male mice after acute and chronic exposure to vehicle engine-derived particulate matter, generated as ultrafine (UFP) and fine (FP) sizes, with additional exposures using UFP or FP combined with gaseous copollutants derived from fresh gasoline and diesel emissions, labeled as UFP + G and FP + G. The UFP and UFP + G exposure groups resulted in the most profound pulmonary and neuroinflammatory effects. Phagocytosis of UFP + G particles via resident alveolar macrophages was substantial in both mouse strains, particularly after chronic exposure, with concurrent increased proinflammatory cytokine expression of CXCL1 and TNFα in the bronchial lavage fluid. In the acute exposure paradigm, only UFP and UFP + G induced significant changes in pulmonary inflammation and only in the ApoE -/- animals. Similarly, acute exposure to UFP and UFP + G increased the expression of several cytokines in the hippocampus of ApoE -/- mice including Il-1β, IL-6, Tgf-β and Tnf-α and in the hippocampus of C57BL/6 mice including Ccl5, Cxcl1, Il-1β, and Tnf-α. Interestingly, Il-6 and Tgf-β expression were decreased in the C57BL/6 hippocampus after acute exposure. Chronic exposure to UFP + G increased expression of Ccl5, Cxcl1, Il-6, and Tgf-β in the ApoE -/- hippocampus, but this effect was minimal in the C57BL/6 mice, suggesting compensatory mechanisms to manage neuroinflammation in this strain. Inflammatory responses the lung and brain were most substantial in ApoE -/- animals exposed to UFP + G, suggesting that the surface area-dependent interaction of gases and particles is an important determinant of toxic responses. As such, freshly generated UFP, in the presence of combustion-derived gas phase pollutants, may be a greater health hazard than would be predicted from PM concentration, alone, lending support for epidemiological findings of adverse neurological outcomes associated with roadway proximity.

Ultrafine particle emissions from essential-oil-based mosquito repellent products.

PubMed

Liu, J; Fung, D; Jiang, J; Zhu, Y

2014-06-01

Ultrafine particle (UFP) emissions from three essential-oil-based mosquito repellent products (lemon eucalyptus (LE), natural insects (NI), and bite shield (BS)) were tested in a 386 l chamber at a high air exchange rate of 24/h with filtered laboratory air. Total particle number concentration and size distribution were monitored by a condensation particle counter and a scanning mobility particle sizer, respectively. UFPs were emitted from all three products under indoor relevant ozone concentrations (~ 17 ppb). LE showed a nucleation burst followed by a relatively stable and continuous emission while the other two products (NI and BS) showed episodic emissions. The estimated maximum particle emission rate varied from 5.4 × 10(9) to 1.2 × 10(12) particles/min and was directly related to the dose of mosquito repellent used. These rates are comparable to those due to other indoor activities such as cooking and printing. The emission duration for LE lasted for 8-78 min depending on the dose applied while the emission duration for NI and BS lasted for 2-3 h. Certain essential-oil-based mosquito repellents can produce high concentrations of UFPs when applied, even at low ozone levels. Household and personal care products that contain essential oil may need to be tested at indoor relevant ozone levels to determine their potential to increase personal UFP exposures. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Fine and ultrafine particle emissions from microwave popcorn.

PubMed

Zhang, Q; Avalos, J; Zhu, Y

2014-04-01

This study characterized fine (PM2.5 ) and ultrafine particle (UFP, diameter < 100 nm) emissions from microwave popcorn and analyzed influential factors. Each pre-packed popcorn bag was cooked in a microwave oven enclosed in a stainless steel chamber for 3 min. The number concentration and size distribution of UFPs and PM2.5 mass concentration were measured inside the chamber repeatedly for five different flavors under four increasing power settings using either the foil-lined original package or a brown paper bag. UFPs and PM2.5 generated by microwaving popcorn were 150-560 and 350-800 times higher than the emissions from microwaving water, respectively. About 90% of the total particles emitted were in the ultrafine size range. The emitted PM concentrations varied significantly with flavor. Replacing the foil-lined original package with a brown paper bag significantly reduced the peak concentration by 24-87% for total particle number and 36-70% for PM2.5 . A positive relationship was observed between both UFP number and PM2.5 mass and power setting. The emission rates of microwave popcorn ranged from 1.9 × 10(10) to 8.0 × 10(10) No./min for total particle number and from 134 to 249 μg/min for PM2.5 . © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Ultrafine Particle Distribution and Chemical Composition Assessment during Military Operative Trainings.

PubMed

Campagna, Marcello; Pilia, Ilaria; Marcias, Gabriele; Frattolillo, Andrea; Pili, Sergio; Bernabei, Manuele; d'Aloja, Ernesto; Cocco, Pierluigi; Buonanno, Giorgio

2017-05-30

(1) Background: The assessment of airborne particulate matter (PM) and ultrafine particles (UFPs) in battlefield scenarios is a topic of particular concern; (2) Methods: Size distribution, concentration, and chemical composition of UFPs during operative military training activities (target drone launches, ammunition blasting, and inert bomb impact) were investigated using an electric low-pressure impactor (ELPI+) and a scanning electron microscope (SEM), equipped with energy-dispersive spectroscopy (EDS); (3) Results: The median of UFPs, measured for all sampling periods and at variable distance from sources, was between 1.02 × 10³ and 3.75 × 10³ particles/cm³ for drone launches, between 3.32 × 10³ and 15.4 × 10³ particles/cm³ for the ammunition blasting and from 7.9 × 10³ to 1.3 × 10⁴ particles/cm³ for inert launches. Maximum peak concentrations, during emitting sources starting, were 75.5 × 10⁶ and 17.9 × 10⁶ particles/cm³, respectively. Particles from the drone launches were predominantly composed of silicon (Si), iron (Fe) and calcium (Ca), and those from the blasting campaigns by magnesium (Mg), sulphur (S), aluminum (Al), iron (Fe), barium (Ba) and silicon (Si); (4) Conclusions: The investigated sources produced UFPs with median values lower than other anthropogenic sources, and with a similar chemical composition.

Physicochemical characteristics and occupational exposure to coarse, fine and ultrafine particles during building refurbishment activities

NASA Astrophysics Data System (ADS)

Azarmi, Farhad; Kumar, Prashant; Mulheron, Mike; Colaux, Julien L.; Jeynes, Chris; Adhami, Siavash; Watts, John F.

2015-08-01

Understanding of the emissions of coarse (PM10 ≤10 μm), fine (PM2.5 ≤2.5 μm) and ultrafine particles (UFP <100 nm) from refurbishment activities and their dispersion into the nearby environment is of primary importance for developing efficient risk assessment and management strategies in the construction and demolition industry. This study investigates the release, occupational exposure and physicochemical properties of particulate matter, including UFPs, from over 20 different refurbishment activities occurring at an operational building site. Particles were measured in the 5-10,000-nm-size range using a fast response differential mobility spectrometer and a GRIMM particle spectrometer for 55 h over 8 days. The UFPs were found to account for >90 % of the total particle number concentrations and <10 % of the total mass concentrations released during the recorded activities. The highest UFP concentrations were 4860, 740, 650 and 500 times above the background value during wall-chasing, drilling, cementing and general demolition activities, respectively. Scanning electron microscopy, X-ray photoelectron spectroscopy and ion beam analysis were used to identify physicochemical characteristics of particles and attribute them to probable sources considering the size and the nature of the particles. The results confirm that refurbishment activities produce significant levels (both number and mass) of airborne particles, indicating a need to develop appropriate regulations for the control of occupational exposure of operatives undertaking building refurbishment.

Frequent ultrafine particle formation and growth in Canadian Arctic marine and coastal environments

NASA Astrophysics Data System (ADS)

Collins, Douglas B.; Burkart, Julia; Chang, Rachel Y.-W.; Lizotte, Martine; Boivin-Rioux, Aude; Blais, Marjolaine; Mungall, Emma L.; Boyer, Matthew; Irish, Victoria E.; Massé, Guillaume; Kunkel, Daniel; Tremblay, Jean-Éric; Papakyriakou, Tim; Bertram, Allan K.; Bozem, Heiko; Gosselin, Michel; Levasseur, Maurice; Abbatt, Jonathan P. D.

2017-11-01

The source strength and capability of aerosol particles in the Arctic to act as cloud condensation nuclei have important implications for understanding the indirect aerosol-cloud effect within the polar climate system. It has been shown in several Arctic regions that ultrafine particle (UFP) formation and growth is a key contributor to aerosol number concentrations during the summer. This study uses aerosol number size distribution measurements from shipboard expeditions aboard the research icebreaker CCGS Amundsen in the summers of 2014 and 2016 throughout the Canadian Arctic to gain a deeper understanding of the drivers of UFP formation and growth within this marine boundary layer. UFP number concentrations (diameter > 4 nm) in the range of 101-104 cm-3 were observed during the two seasons, with concentrations greater than 103 cm-3 occurring more frequently in 2016. Higher concentrations in 2016 were associated with UFP formation and growth, with events occurring on 41 % of days, while events were only observed on 6 % of days in 2014. Assessment of relevant parameters for aerosol nucleation showed that the median condensation sink in this region was approximately 1.2 h-1 in 2016 and 2.2 h-1 in 2014, which lie at the lower end of ranges observed at even the most remote stations reported in the literature. Apparent growth rates of all observed events in both expeditions averaged 4.3 ± 4.1 nm h-1, in general agreement with other recent studies at similar latitudes. Higher solar radiation, lower cloud fractions, and lower sea ice concentrations combined with differences in the developmental stage and activity of marine microbial communities within the Canadian Arctic were documented and help explain differences between the aerosol measurements made during the 2014 and 2016 expeditions. These findings help to motivate further studies of biosphere-atmosphere interactions within the Arctic marine environment to explain the production of UFP and their growth to sizes relevant for cloud droplet activation.

High efficiency cabin air filter in vehicles reduces drivers' roadway particulate matter exposures and associated lipid peroxidation

PubMed Central

Shu, Shi; Lin, Yan; She, Jianwen; Ip, Ho Sai Simon; Qiu, Xinghua; Zhu, Yifang

2017-01-01

Commuters who spend long hours on roads are exposed to high levels of traffic related air pollutants (TRAPs). Despite some well-known multiple adverse effects of TRAPs on human health, limited studies have focused on mitigation strategies to reduce these effects. In this study, we measured fine particulate matter (PM2.5) and ultrafine particle (UFP) concentrations inside and outside 17 taxis simultaneously while they were driven on roadways. The drivers’ urinary monohydroxylated polycyclic aromatic hydrocarbons (OH-PAHs) and malondialdehyde (MDA) concentrations just before and right after the driving tests were also determined. Data were collected under three driving conditions (i.e. no mitigation (NM), window closed (WC), and window closed plus using high efficiency cabin air filters (WC+HECA)) for each taxi and driver. The results show that, compared to NM, the WC+HECA reduced in-cabin PM2.5 and UFP concentrations, by 37% and 47% respectively (p < 0.05), whereas the reductions on PAH exposures were insignificant. Although nonsignificant, a reduction of 17% was also observed in the drivers’ urinary MDA under WC+HECA. The MDA concentrations were found to be significantly associated with the in-cabin PM2.5 and UFP concentrations, suggesting the reduction of the drivers’ lipid peroxidation can be at least partially attributed to the PM2.5 and UFP reduction by WC+HECA. Overall, these results suggest HECA filters have potential to reduce particle levels inside taxis and protect drivers’ health. PMID:29176859

High efficiency cabin air filter in vehicles reduces drivers' roadway particulate matter exposures and associated lipid peroxidation.

PubMed

Yu, Nu; Shu, Shi; Lin, Yan; She, Jianwen; Ip, Ho Sai Simon; Qiu, Xinghua; Zhu, Yifang

2017-01-01

Commuters who spend long hours on roads are exposed to high levels of traffic related air pollutants (TRAPs). Despite some well-known multiple adverse effects of TRAPs on human health, limited studies have focused on mitigation strategies to reduce these effects. In this study, we measured fine particulate matter (PM2.5) and ultrafine particle (UFP) concentrations inside and outside 17 taxis simultaneously while they were driven on roadways. The drivers' urinary monohydroxylated polycyclic aromatic hydrocarbons (OH-PAHs) and malondialdehyde (MDA) concentrations just before and right after the driving tests were also determined. Data were collected under three driving conditions (i.e. no mitigation (NM), window closed (WC), and window closed plus using high efficiency cabin air filters (WC+HECA)) for each taxi and driver. The results show that, compared to NM, the WC+HECA reduced in-cabin PM2.5 and UFP concentrations, by 37% and 47% respectively (p < 0.05), whereas the reductions on PAH exposures were insignificant. Although nonsignificant, a reduction of 17% was also observed in the drivers' urinary MDA under WC+HECA. The MDA concentrations were found to be significantly associated with the in-cabin PM2.5 and UFP concentrations, suggesting the reduction of the drivers' lipid peroxidation can be at least partially attributed to the PM2.5 and UFP reduction by WC+HECA. Overall, these results suggest HECA filters have potential to reduce particle levels inside taxis and protect drivers' health.

Comparison of Mutagenic Activities of Various Ultra-Fine Particles.

PubMed

Park, Chang Gyun; Cho, Hyun Ki; Shin, Han Jae; Park, Ki Hong; Lim, Heung Bin

2018-04-01

Air pollution is increasing, along with consumption of fossil fuels such as coal and diesel gas. Air pollutants are known to be a major cause of respiratory-related illness and death, however, there are few reports on the genotoxic characterization of diverse air pollutants in Korea. In this study, we investigated the mutagenic activity of various particles such as diesel exhaust particles (DEP), combustion of rice straw (RSC), pine stem (PSC), and coal (CC), tunnel dust (TD), and road side dust (RD). Ultra-fine particles (UFPs) were collected by the glass fiber filter pad. Then, we performed a chemical analysis to see each of the component features of each particulate matter. The mutagenicity of various UFPs was determined by the Ames test with four Salmonella typhimurium strains with or without metabolic activation. The optimal concentrations of UFPs were selected based on result of a concentration decision test. Moreover, in order to compare relative mutagenicity among UFPs, we selected and tested DEP as mutation reference. DEP, RSC, and PSC induced concentration-dependent increases in revertant colony numbers with TA98, TA100, and TA1537 strains in the absence and presence of metabolic activation. DEP showed the highest specific activity among the particulate matters. In this study, we conclude that DEP, RSC, PSC, and TD displayed varying degrees of mutagenicity, and these results suggest that the mutagenicity of these air pollutants is associated with the presence of polycyclic aromatic hydrocarbons (PAHs) in these particulate matters.

Comparisons of Traffic-Related Ultrafine Particle Number Concentrations Measured in Two Urban Areas by Central, Residential, and Mobile Monitoring.

PubMed

Simon, Matthew C; Hudda, Neelakshi; Naumova, Elena N; Levy, Jonathan I; Brugge, Doug; Durant, John L

2017-11-01

Traffic-related ultrafine particles (UFP; <100 nanometers diameter) are ubiquitous in urban air. While studies have shown that UFP are toxic, epidemiological evidence of health effects, which is needed to inform risk assessment at the population scale, is limited due to challenges of accurately estimating UFP exposures. Epidemiologic studies often use empirical models to estimate UFP exposures; however, the monitoring strategies upon which the models are based have varied between studies. Our study compares particle number concentrations (PNC; a proxy for UFP) measured by three different monitoring approaches (central-site, short-term residential-site, and mobile on-road monitoring) in two study areas in metropolitan Boston (MA, USA). Our objectives were to quantify ambient PNC differences between the three monitoring platforms, compare the temporal patterns and the spatial heterogeneity of PNC between the monitoring platforms, and identify factors that affect correlations across the platforms. We collected >12,000 hours of measurements at the central sites, 1,000 hours of measurements at each of 20 residential sites in the two study areas, and >120 hours of mobile measurements over the course of ~1 year in each study area. Our results show differences between the monitoring strategies: mean one-minute PNC on-roads were higher (64,000 and 32,000 particles/cm 3 in Boston and Chelsea, respectively) compared to central-site measurements (23,000 and 19,000 particles/cm 3 ) and both were higher than at residences (14,000 and 15,000 particles/cm 3 ). Temporal correlations and spatial heterogeneity also differed between the platforms. Temporal correlations were generally highest between central and residential sites, and lowest between central-site and on-road measurements. We observed the greatest spatial heterogeneity across monitoring platforms during the morning rush hours (06:00-09:00) and the lowest during the overnight hours (18:00-06:00). Longer averaging times (days and hours vs. minutes) increased temporal correlations (Pearson correlations were 0.69 and 0.60 vs. 0.39 in Boston; 0.71 and 0.61 vs. 0.45 in Chelsea) and reduced spatial heterogeneity (coefficients of divergence were 0.24 and 0.29 vs. 0.33 in Boston; 0.20 and 0.27 vs. 0.31 in Chelsea). Our results suggest that combining stationary and mobile monitoring may lead to improved characterization of UFP in urban areas and thereby lead to improved exposure assignment for epidemiology studies.

Napping-Ultra Flash Profile as a Tool for Category Identification and Subsequent Model System Formulation of Caramel Corn Products.

PubMed

Mayhew, Emily; Schmidt, Shelly; Lee, Soo-Yeun

2016-07-01

In a novel approach to formulation, the flash descriptive profiling technique Napping-Ultra Flash Profile (Napping-UFP) was used to characterize a wide range of commercial caramel corn products. The objectives were to identify product categories, develop model systems based on product categories, and correlate analytical parameters with sensory terms generated through the Napping-UFP exercise. In one 2 h session, 12 panelists participated in 4 Napping-UFP exercises, describing and grouping, on a 43×56 cm paper sheet, 12 commercial caramel corn samples by degree of similarity, globally and in terms of aroma-by-mouth, texture, and taste. The coordinates of each sample's placement on the paper sheet and descriptive terms generated by the panelists were used to conduct Multiple Factor Analysis (MFA) and hierarchical clustering of the samples. Strong trends in the clustering of samples across the 4 Napping-UFP exercises resulted in the determination of 3 overarching types of commercial caramel corn: "small-scale dark" (typified by burnt, rich caramel corn), "large-scale light" (typified by light and buttery caramel corn), and "large-scale dark" (typified by sweet and molasses-like caramel corn). Representative samples that best exemplified the properties of each category were used as guides in the formulation of 3 model systems that represent the spread of commercial caramel corn products. Analytical testing of the commercial products, including aw measurement, moisture content determination, and thermal characterization via differential scanning calorimetry, were conducted and results related to sensory descriptors using Spearman's correlation. © 2016 Institute of Food Technologists®

Relationships of outdoor and indoor ultrafine particles at residences downwind of a major international border crossing in Buffalo, NY.

PubMed

McAuley, T R; Fisher, R; Zhou, X; Jaques, P A; Ferro, A R

2010-08-01

During winter 2006, indoor and outdoor ultrafine particle (UFP) size distribution measurements for particles with diameters from 5.6 to 165 nm were taken at five homes in a neighborhood directly adjacent to the Peace Bridge Complex (PBC), a major international border crossing connecting Buffalo, New York to Fort Erie, Ontario. Monitoring with 1-s time resolution was conducted for several hours at each home. Participants were instructed to keep all external windows and doors closed and to refrain from cooking, smoking, or other activity that may result in elevating the indoor UFP number concentration. Although the construction and age for the homes were similar, indoor-to-outdoor comparisons indicate that particle infiltration rates varied substantially. Overall, particle concentrations indoors were lower and less variable than particle concentrations outdoors, with average indoor-outdoor ratios ranging from 0.1 to 0.5 (mean 0.34) for particles between 5.6 and 165 nm in diameter. With no indoor sources, the average indoor-outdoor ratios were lowest (0.2) for 20-nm particles, higher (0.3) for particles <10 nm, and highest (0.5) for particles 70-165 nm. This study provides insight into the penetration of UFP into homes and the resulting change in particle size distributions as particles move indoors near a major diesel traffic source. Although people spend most of their time in their homes, exposure estimates for epidemiological studies are generally determined using ambient concentrations. The findings of this study will contribute to improved size-resolved UFP exposure estimates for near roadway exposure assessments and epidemiological studies.

Developmental Neurotoxicity of Inhaled Ambient Ultrafine Particle Air Pollution: Parallels with Neuropathological and Behavioral Features of Autism and Other Neurodevelopmental Disorders

PubMed Central

Allen, J. L.; Oberdorster, G.; Morris-Schafer, K.; Wong, C.; Klocke, C.; Sobolewski, M.; Conrad, K.; Mayer-Proschel, M.; Cory-Slechta, D. A.

2016-01-01

Accumulating evidence from both human and animal studies show that brain is a target of air pollution. Multiple epidemiological studies have now linked components of air pollution to diagnosis of autism spectrum disorder (ASD), a linkage with plausibility based on the shared mechanisms of inflammation. Additional plausibility appears to be provided by findings from our studies in mice of exposures from postnatal day (PND) 4-7 and 10-13 (human 3rd trimester equivalent), to concentrated ambient ultrafine (UFP) particles, considered the most reactive component of air pollution, at levels consistent with high traffic areas of major U.S. cities and thus highly relevant to human exposures. These exposures, occurring during a period of marked neuro- and gliogenesis, unexpectedly produced a pattern of developmental neurotoxicity notably similar to multiple hypothesized mechanistic underpinnings of ASD, including its greater impact in males. UFP exposures induced inflammation/microglial activation, reductions in size of the corpus callosum (CC) and associated hypomyelination, aberrant white matter development and/or structural integrity with ventriculomegaly (VM), elevated glutamate and excitatory/inhibitory imbalance, increased amygdala astrocytic activation, and repetitive and impulsive behaviors. Collectively, these findings suggest the human 3rd trimester equivalent as a period of potential vulnerability to neurodevelopmental toxicity to UFP, particularly in males, and point to the possibility that UFP air pollution exposure during periods of rapid neuro- and gliogenesis may be a risk factor not only for ASD, but also for other neurodevelopmental disorders that share features with ASD, such as schizophrenia, attention deficit disorder, and periventricular leukomalacia. PMID:26721665

Modeling multi-scale aerosol dynamics and micro-environmental air quality near a large highway intersection using the CTAG model.

PubMed

Wang, Yan Jason; Nguyen, Monica T; Steffens, Jonathan T; Tong, Zheming; Wang, Yungang; Hopke, Philip K; Zhang, K Max

2013-01-15

A new methodology, referred to as the multi-scale structure, integrates "tailpipe-to-road" (i.e., on-road domain) and "road-to-ambient" (i.e., near-road domain) simulations to elucidate the environmental impacts of particulate emissions from traffic sources. The multi-scale structure is implemented in the CTAG model to 1) generate process-based on-road emission rates of ultrafine particles (UFPs) by explicitly simulating the effects of exhaust properties, traffic conditions, and meteorological conditions and 2) to characterize the impacts of traffic-related emissions on micro-environmental air quality near a highway intersection in Rochester, NY. The performance of CTAG, evaluated against with the field measurements, shows adequate agreement in capturing the dispersion of carbon monoxide (CO) and the number concentrations of UFPs in the near road micro-environment. As a proof-of-concept case study, we also apply CTAG to separate the relative impacts of the shutdown of a large coal-fired power plant (CFPP) and the adoption of the ultra-low-sulfur diesel (ULSD) on UFP concentrations in the intersection micro-environment. Although CTAG is still computationally expensive compared to the widely-used parameterized dispersion models, it has the potential to advance our capability to predict the impacts of UFP emissions and spatial/temporal variations of air pollutants in complex environments. Furthermore, for the on-road simulations, CTAG can serve as a process-based emission model; Combining the on-road and near-road simulations, CTAG becomes a "plume-in-grid" model for mobile emissions. The processed emission profiles can potentially improve regional air quality and climate predictions accordingly. Copyright © 2012 Elsevier B.V. All rights reserved.

Short-Term Mortality Rates during a Decade of Improved Air Quality in Erfurt, Germany

PubMed Central

Breitner, Susanne; Stölzel, Matthias; Cyrys, Josef; Pitz, Mike; Wölke, Gabriele; Kreyling, Wolfgang; Küchenhoff, Helmut; Heinrich, Joachim; Wichmann, H.-Erich; Peters, Annette

2009-01-01

Background Numerous studies have shown associations between ambient air pollution and daily mortality. Objectives Our goal was to investigate the association of ambient air pollution and daily mortality in Erfurt, Germany, over a 10.5-year period after the German unification, when air quality improved. Methods We obtained daily mortality counts and data on mass concentrations of particulate matter (PM) < 10 μm in aerodynamic diameter (PM10), gaseous pollutants, and meteorology in Erfurt between October 1991 and March 2002. We obtained ultrafine particle number concentrations (UFP) and mass concentrations of PM < 2.5 μm in aerodynamic diameter (PM2.5) from September 1995 to March 2002. We analyzed the data using semiparametric Poisson regression models adjusting for trend, seasonality, influenza epidemics, day of the week, and meteorology. We evaluated cumulative associations between air pollution and mortality using polynomial distributed lag (PDL) models and multiday moving averages of air pollutants. We evaluated changes in the associations over time in time-varying coefficient models. Results Air pollution concentrations decreased over the study period. Cumulative exposure to UFP was associated with increased mortality. An interquartile range (IQR) increase in the 15-day cumulative mean UFP of 7,649 cm−3 was associated with a relative risk (RR) of 1.060 [95% confidence interval (CI), 1.008–1.114] for PDL models and an RR/IQR of 1.055 (95% CI, 1.011–1.101) for moving averages. RRs decreased from the mid-1990s to the late 1990s. Conclusion Results indicate an elevated mortality risk from short-term exposure to UFP. They further suggest that RRs for short-term associations of air pollution decreased as pollution control measures were implemented in Eastern Germany. PMID:19337521

Developmental neurotoxicity of inhaled ambient ultrafine particle air pollution: Parallels with neuropathological and behavioral features of autism and other neurodevelopmental disorders.

PubMed

Allen, J L; Oberdorster, G; Morris-Schaffer, K; Wong, C; Klocke, C; Sobolewski, M; Conrad, K; Mayer-Proschel, M; Cory-Slechta, D A

2017-03-01

Accumulating evidence from both human and animal studies show that brain is a target of air pollution. Multiple epidemiological studies have now linked components of air pollution to diagnosis of autism spectrum disorder (ASD), a linkage with plausibility based on the shared mechanisms of inflammation. Additional plausibility appears to be provided by findings from our studies in mice of exposures from postnatal day (PND) 4-7 and 10-13 (human 3rd trimester equivalent), to concentrated ambient ultrafine (UFP) particles, considered the most reactive component of air pollution, at levels consistent with high traffic areas of major U.S. cities and thus highly relevant to human exposures. These exposures, occurring during a period of marked neuro- and gliogenesis, unexpectedly produced a pattern of developmental neurotoxicity notably similar to multiple hypothesized mechanistic underpinnings of ASD, including its greater impact in males. UFP exposures induced inflammation/microglial activation, reductions in size of the corpus callosum (CC) and associated hypomyelination, aberrant white matter development and/or structural integrity with ventriculomegaly (VM), elevated glutamate and excitatory/inhibitory imbalance, increased amygdala astrocytic activation, and repetitive and impulsive behaviors. Collectively, these findings suggest the human 3rd trimester equivalent as a period of potential vulnerability to neurodevelopmental toxicity to UFP, particularly in males, and point to the possibility that UFP air pollution exposure during periods of rapid neuro- and gliogenesis may be a risk factor not only for ASD, but also for other neurodevelopmental disorders that share features with ASD, such as schizophrenia, attention deficit disorder, and periventricular leukomalacia. Copyright © 2015 Elsevier B.V. All rights reserved.

Measurements of ultrafine particles and other vehicular pollutants inside school buses in South Texas

NASA Astrophysics Data System (ADS)

Zhang, Qunfang; Zhu, Yifang

2010-01-01

Increasing evidence has demonstrated toxic effects of vehicular emitted ultrafine particles (UFPs, diameter < 100 nm), with the highest human exposure usually occurring on and near roadways. Children are particularly at risk due to immature respiratory systems and faster breathing rates. In this study, children's exposure to in-cabin air pollutants, especially UFPs, was measured inside four diesel-powered school buses. Two 1990 and two 2006 model year diesel-powered school buses were selected to represent the age extremes of school buses in service. Each bus was driven on two routine bus runs to study school children's exposure under different transportation conditions in South Texas. The number concentration and size distribution of UFPs, total particle number concentration, PM 2.5, PM 10, black carbon (BC), CO, and CO 2 levels were monitored inside the buses. The average total particle number concentrations observed inside the school buses ranged from 7.3 × 10 3 to 3.4 × 10 4 particles cm -3, depending on engine age and window position. When the windows were closed, the in-cabin air pollutants were more likely due to the school buses' self-pollution. The 1990 model year school buses demonstrated much higher air pollutant concentrations than the 2006 model year ones. When the windows were open, the majority of in-cabin air pollutants came from the outside roadway environment with similar pollutant levels observed regardless of engine ages. The highest average UFP concentration was observed at a bus transfer station where approximately 27 idling school buses were queued to load or unload students. Starting-up and idling generated higher air pollutant levels than the driving state. Higher in-cabin air pollutant concentrations were observed when more students were on board.

A travel mode comparison of commuters' exposures to air pollutants in Barcelona

NASA Astrophysics Data System (ADS)

de Nazelle, Audrey; Fruin, Scott; Westerdahl, Dane; Martinez, David; Ripoll, Anna; Kubesch, Nadine; Nieuwenhuijsen, Mark

2012-11-01

Daily commutes may contribute disproportionately to overall daily inhalations of urban air contaminants. Understanding factors that explain variability of exposures during travel, and especially differences across transportation modes, is essential to accurately assess health impacts of traffic emissions and to develop effective mitigating measures. We evaluated exposures and inhaled doses of air pollution and assessed factors that contributed to their variability in different travel modes in Barcelona. Black carbon (BC), ultrafine particles (UFP), carbon monoxide (CO), fine particle mass (PM2.5) and carbon dioxide (CO2) were measured and compared across walk, bike, bus, and car modes for a total of 172 trips made on two different round trip routes. On average, the car mode experienced highest concentrations for all contaminants. In pairwise t-tests between concurrent mode runs, statistically significant differences were found for cars compared to walking and biking. Car-to-walk or car-to-bike concentration ratios ranged from 1.3 for CO2 to 25 for CO and were 2-3 for PM2.5, BC, and UFP. In multivariate analyses, travel mode explained the greatest variability in travel exposures, from 8% for PM2.5 to 70% for CO. Different modal patterns emerged when estimating daily inhaled dose, with active commuters' two to three times greater total inhalation volume during travel producing about equal UFP and BC daily inhaled doses to car commuters and 33-50% higher UFP and BC doses compared to bus commuters. These findings, however, are specific to the bike and pedestrian lanes in this study being immediately adjacent to the roadways measured. Dedicated bike or pedestrian routes away from traffic would lead to lower active travel doses.

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

NASA Astrophysics Data System (ADS)

Fruin, S.; Westerdahl, D.; Sax, T.; Sioutas, C.; Fine, P. M.

Motor vehicles are the dominant source of oxides of nitrogen (NO x), particulate matter (PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction (˜6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated with readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles.

Gene expression profile in circulating mononuclear cells after exposure to ultrafine carbon particles

PubMed Central

Huang, Yuh-Chin T.; Schmitt, Michael; Yang, Zhonghui; Que, Loretta G.; Stewart, Judith C.; Frampton, Mark W.; Devlin, Robert B.

2013-01-01

Context Exposure to particulate matter (PM) is associated with systemic health effects, but the cellular and molecular mechanisms are unclear. Objective We hypothesized that, if circulating mononuclear cells play an important role in mediating systemic effects of PM, they would show gene expression changes following exposure. Materials and methods Peripheral blood samples were collected before (0 hour) and at 24 hours after exposure from healthy subjects who participated in previous controlled exposures to ultrafine carbon particles (UFP, 50 μg/m3) or filtered air (FA)(n = 3 each). RNA from mononuclear cell fraction (>85% lymphocytes) was extracted, amplified and hybridized to Affymetrix HU133 plus 2 microarrays. Results We identified 1713 genes (UFP 24 hours vs. FA 0 and 24 hours, p < 0.05, FDR 0.01). The top 10 upregulated genes (fold) were CDKN1C (1.86), ZNF12 (1.83), SRGAP2 (1.82), FYB (1.79), LSM14B (1.79), CD93 (1.76), NCSTN (1.70), DUSP6 (1.69), TACC1 (1.68) and H2AFY (1.68). Upregulation of CDKN1C and SRGAP2 was confirmed by RT-PCR using samples from additional 5 subjects exposed to FA and UFP. We entered 1020 genes with a ratio >1.1 or <−1.1 into the Ingenuity Pathway Analysis and identified many canonical pathways related to inflammation, tissue growth and host defense against environmental insults, including IGF-1 signaling, insulin receptor signaling and NRF2-mediated oxidative stress response pathway. Discussion and conclusions Two-hour exposures to UFP produced gene expression changes in circulating mononuclear cells. These gene changes provide biologically plausible links to PM-induced systemic health effects, especially those in the cardiovascular system and glucose metabolism. PMID:20507211

Real-Time Measurements and Characterization of Airborne Particulate Matter from a Primary Silicon Carbide Production Plant.

PubMed

Jørgensen, Rikke Bramming; Kero, Ida Teresia

2017-12-20

Airborne particulate matter in the silicon carbide (SiC) industry is a known health hazard. The aims of this study were to elucidate whether the particulate matter generated inside the Acheson furnace during active operation is representative of the overall particulate matter in the furnace hall, and whether the Acheson furnaces are the main sources of ultrafine particles (UFP) in primary SiC production. The number concentration of ultrafine particles was evaluated using an Electrical Low Pressure Impactor (ELPI TM , Dekati Ltd., Tampere, Finland), a Fast Mobility Particle Sizer (FMPS TM , TSI, Shoreview, MN, USA) and a Condensation Particle Counter (CPC, TSI, Shoreview, MN, USA). The results are discussed in terms of particle number concentration, particle size distribution and are also characterized by means of electron microscopy (TEM/SEM). Two locations were investigated; the industrial Acheson process furnace hall and a pilot furnace hall; both of which represent an active operating furnace. The geometric mean of the particle number concentration in the Acheson process furnace hall was 7.7 × 10⁴ particles/cm³ for the UFP fraction and 1.0 × 10⁵ particles/cm³ for the submicrometre fraction. Particulate matter collected at the two sites was analysed by electron microscopy. The PM from the Acheson process furnace hall is dominated by carbonaceous particles while the samples collected near the pilot furnace are primarily rich in silicon.

Real-Time Measurements and Characterization of Airborne Particulate Matter from a Primary Silicon Carbide Production Plant

PubMed Central

2017-01-01

Airborne particulate matter in the silicon carbide (SiC) industry is a known health hazard. The aims of this study were to elucidate whether the particulate matter generated inside the Acheson furnace during active operation is representative of the overall particulate matter in the furnace hall, and whether the Acheson furnaces are the main sources of ultrafine particles (UFP) in primary SiC production. The number concentration of ultrafine particles was evaluated using an Electrical Low Pressure Impactor (ELPITM, Dekati Ltd., Tampere, Finland), a Fast Mobility Particle Sizer (FMPSTM, TSI, Shoreview, MN, USA) and a Condensation Particle Counter (CPC, TSI, Shoreview, MN, USA). The results are discussed in terms of particle number concentration, particle size distribution and are also characterized by means of electron microscopy (TEM/SEM). Two locations were investigated; the industrial Acheson process furnace hall and a pilot furnace hall; both of which represent an active operating furnace. The geometric mean of the particle number concentration in the Acheson process furnace hall was 7.7 × 104 particles/cm3 for the UFP fraction and 1.0 × 105 particles/cm3 for the submicrometre fraction. Particulate matter collected at the two sites was analysed by electron microscopy. The PM from the Acheson process furnace hall is dominated by carbonaceous particles while the samples collected near the pilot furnace are primarily rich in silicon. PMID:29261158

Longitudinal association between air pollution exposure at school and cognitive development in school children over a period of 3.5 years.

PubMed

Forns, Joan; Dadvand, Payam; Esnaola, Mikel; Alvarez-Pedrerol, Mar; López-Vicente, Mònica; Garcia-Esteban, Raquel; Cirach, Marta; Basagaña, Xavier; Guxens, Mònica; Sunyer, Jordi

2017-11-01

Recently, we showed that exposure to traffic-related air pollutants (TRAPs) at school was negatively associated with cognitive development, specifically working memory and inattentiveness, in primary schoolchildren during a course of 12 months. The persistence of such associations over longer periods remains as an open question. To study the longitudinal association between TRAPs at school and cognitive development over a period of 3.5 years. Indoor and outdoor levels of TRAPs (elemental carbon (EC), dioxide nitrogen (NO 2 ), particulate matter (PM 2.5 ) from traffic sources and ultrafine particles (UFP)) were measured at 39 schools across Barcelona during 2012/2013. Working memory, as a measure of cognitive development, was evaluated 4 times in 2012/2013 assessment and was re-evaluated one more time in 2015 using computerized n-back test (3-back d' as main outcome). Linear mixed effects models were used to test the association between TRAPs and 3-back d', adding child and school as random effects to account for the multilevel nature of the data, and school air pollutants levels (one at a time) as predictor. We found detrimental associations between all TRAPs and annual change in 3-back d' (working memory) (i.e. slower development of working memory in children attending schools with higher levels of air pollution). The associations (per one interquartile range increase in exposure) were strongest for outdoor NO 2 (Coefficient (Coef) = - 4.22, 95% confidence interval (CI), - 6.22, - 2.22) and indoor UFP (Coef = - 4.12, 95%CI, - 5.68, - 1.83). These reductions were equivalent to - 20% (95%CI, - 30.1, - 10.7) and - 19.9% (95%CI, - 31.5, - 8.4) change in annual working memory development associated with one interquartile range increase in outdoor NO 2 and indoor UFP, respectively. Our findings suggest the persistence of the negative association between TRAPs exposure at school and cognitive trajectory measured by n-back test over a period of 3.5 years. Copyright © 2017 Elsevier Inc. All rights reserved.

Numerical modeling of particle generation from ozone reactions with human-worn clothing in indoor environments

NASA Astrophysics Data System (ADS)

Rai, Aakash C.; Lin, Chao-Hsin; Chen, Qingyan

2015-02-01

Ozone-terpene reactions are important sources of indoor ultrafine particles (UFPs), a potential health hazard for human beings. Humans themselves act as possible sites for ozone-initiated particle generation through reactions with squalene (a terpene) that is present in their skin, hair, and clothing. This investigation developed a numerical model to probe particle generation from ozone reactions with clothing worn by humans. The model was based on particle generation measured in an environmental chamber as well as physical formulations of particle nucleation, condensational growth, and deposition. In five out of the six test cases, the model was able to predict particle size distributions reasonably well. The failure in the remaining case demonstrated the fundamental limitations of nucleation models. The model that was developed was used to predict particle generation under various building and airliner cabin conditions. These predictions indicate that ozone reactions with human-worn clothing could be an important source of UFPs in densely occupied classrooms and airliner cabins. Those reactions could account for about 40% of the total UFPs measured on a Boeing 737-700 flight. The model predictions at this stage are indicative and should be improved further.

Spatial variation of ultrafine particles and black carbon in two cities: results from a short-term measurement campaign.

PubMed

Klompmaker, Jochem O; Montagne, Denise R; Meliefste, Kees; Hoek, Gerard; Brunekreef, Bert

2015-03-01

Recently, short-term monitoring campaigns have been carried out to investigate the spatial variation of air pollutants within cities. Typically, such campaigns are based on short-term measurements at relatively large numbers of locations. It is largely unknown how well these studies capture the spatial variation of long term average concentrations. The aim of this study was to evaluate the within-site temporal and between-site spatial variation of the concentration of ultrafine particles (UFPs) and black carbon (BC) in a short-term monitoring campaign. In Amsterdam and Rotterdam (the Netherlands) measurements of number counts of particles larger than 10nm as a surrogate for UFP and BC were performed at 80 sites per city. Each site was measured in three different seasons of 2013 (winter, spring, summer). Sites were selected from busy urban streets, urban background, regional background and near highways, waterways and green areas, to obtain sufficient spatial contrast. Continuous measurements were performed for 30 min per site between 9 and 16 h to avoid traffic spikes of the rush hour. Concentrations were simultaneously measured at a reference site to correct for temporal variation. We calculated within- and between-site variance components reflecting temporal and spatial variations. Variance ratios were compared with previous campaigns with longer sampling durations per sample (24h to 14 days). The within-site variance was 2.17 and 2.44 times higher than the between-site variance for UFP and BC, respectively. In two previous studies based upon longer sampling duration much smaller variance ratios were found (0.31 and 0.09 for UFP and BC). Correction for temporal variation from a reference site was less effective for the short-term monitoring campaign compared to the campaigns with longer duration. Concentrations of BC and UFP were on average 1.6 and 1.5 times higher at urban street compared to urban background sites. No significant differences between the other site types and urban background were found. The high within to between-site concentration variances may result in the loss of precision and low explained variance when average concentrations from short-term campaigns are used to develop land use regression models. Copyright © 2014 Elsevier B.V. All rights reserved.

Measurements of fine and ultrafine particles formation in photocopy centers in Taiwan

NASA Astrophysics Data System (ADS)

Lee, Chia-Wei; Hsu, Der-Jen

This study investigates the levels of particulate matter smaller than 2.5 μm (PM 2.5) and some selected volatile organic compounds (VOCs) at 12 photocopy centers in Taiwan from November 2004 to June 2005. The results of BTEXS (benzene, toluene, ethylbenzene, xylenes and styrene) measurements indicated that toluene had the highest concentration in all photocopy centers, while the concentration of the other four compounds varied among the 12 photocopy centers. The average background-corrected eight-hour PM 2.5 in the 12 photocopy centers ranged from 10 to 83 μg m -3 with an average of 40 μg m -3. The 24-h indoor PM 2.5 at the photocopy centers was estimated and at two photocopy centers exceeded 100 μg m -3, the 24-h indoor PM 2.5 guideline recommended by the Taiwan EPA. The ozone level and particle size distribution at another photocopy center were monitored and indicated that the ozone level increased when the photocopying started and the average ozone level at some photocopy centers during business hour may exceed the value (50 ppb) recommended by the Taiwan EPA. The particle size distribution monitored during photocopying indicated that the emitted particles were much smaller than the original toner powders. Additionally, the number concentration of particles that were smaller than 0.5 μm was found to increase during the first hour of photocopying and it increased as the particle size decreased. The ultrafine particle (UFP, <100 nm) dominated the number concentration and the peak concentration appeared at sizes of under 50 nm. A high number concentration of UFP was found with a peak value of 1E+8 particles cm -3 during photocopying. The decline of UFP concentration was observed after the first hour and the decline is likely attributable to the surface deposition of charged particles, which are charged primarily by the diffusion charging of corona devices in the photocopier. This study concludes that ozone and UFP concentrations in photocopy centers should be concerned in view of indoor air quality and human health. The corona devices in photocopiers and photocopier-emitted VOCs have the potential to initiate indoor air chemistry during photocopying and result in the formation of UFP.

Performance of school bus retrofit systems: ultrafine particles and other vehicular pollutants.

PubMed

Zhang, Qunfang; Zhu, Yifang

2011-08-01

This study evaluated the performance of retrofit systems for diesel-powered school buses, a diesel oxidation catalyst (DOC) muffler and a spiracle crankcase filtration system (CFS), regarding ultrafine particles (UFPs) and other air pollutants from tailpipe emissions and inside bus cabins. Tailpipe emissions and in-cabin air pollutant levels were measured before and after retrofitting when the buses were idling and during actual pick-up/drop off routes. Retrofit systems significantly reduced tailpipe emissions with a reduction of 20-94% of total particles with both DOC and CFS installed. However, no unequivocal decrease was observed for in-cabin air pollutants after retrofitting. The AC/fan unit and the surrounding air pollutant concentrations played more important roles for determining the in-cabin air quality of school buses than did retrofit technologies. Although current retrofit systems reduce children's exposure while waiting to board at a bus station, retrofitting by itself does not protect children satisfactorily from in-cabin particle exposures. Turning on the bus engine increased in-cabin UFP levels significantly only when the wind blew from the bus' tailpipe toward its hood with its windows open. This indicated that wind direction and window position are significant factors determining how much self-released tailpipe emissions may penetrate into the bus cabin. The use of an air purifier was found to remove in-cabin particles by up to 50% which might be an alternative short-to-medium term strategy to protect children's health.

Characterizing ultrafine particles and other air pollutants in and around school buses.

PubMed

Zhu, Yifang; Zhang, Qunfang

2014-03-01

Increasing evidence has demonstrated toxic effects of ultrafine particles (UFP*, diameter < 100 nm). Children are particularly at risk because of their immature respiratory systems and higher breathing rates per body mass. This study aimed to characterize UFP, PM2.5 (particulate matter < or = 2.5 microm in aerodynamic diameter), and other vehicular-emitted pollutants in and around school buses. Four sub-studies were conducted, including: 1. On-road tests to measure in-cabin air pollutant levels while school buses were being driven; 2. Idling tests to determine the contributions of tailpipe emissions from idling school buses to air pollutant levels in and around school buses under different scenarios; 3. Retrofit tests to evaluate the performance of two retrofit systems, a diesel oxidation catalyst (DOC) muffler and a crankcase filtration system (CFS), on reducing tailpipe emissions and in-cabin air pollutant concentrations under idling and driving conditions; and 4. High efficiency particulate air (HEPA) filter air purifier tests to evaluate the effectiveness of in-cabin filtration. In total, 24 school buses were employed to cover a wide range of school buses commonly used in the United States. Real-time air quality measurements included particle number concentration (PNC), fine and UFP size distribution in the size range 7.6-289 nm, PM2.5 mass concentration, black carbon (BC) concentration, and carbon monoxide (CO) and carbon dioxide (CO2) concentrations. For in-cabin measurements, instruments were placed on a platform secured to the rear seats inside the school buses. For all other tests, a second set of instruments was deployed to simultaneously measure the ambient air pollutant levels. For tailpipe emission measurements, the exhaust was diluted and then measured by instruments identical to those used for the in-cabin measurements. The results show that when driving on roads, in-cabin PNC, fine and UFP size distribution, PM2.5, BC, and CO varied by engine age, window position, driving speed, driving route, and operating conditions. Emissions from idling school buses increased the PNC close to the tailpipe by a factor of up to 26.0. Under some circumstances, tailpipe emissions of idling school buses increased the in-cabin PNC by factors ranging from 1.2 to 5.8 in the 10-30 nm particle size range. Retrofit systems significantly reduced the tailpipe emissions of idling school buses. With both DOC and CFS installed, PNC in tailpipe emissions dropped by 20%-94%. No unequivocal decrease was observed for in-cabin air pollutants after retrofitting. The operation of the air conditioning (AC) unit and the pollutant concentrations in the surrounding ambient air played more important roles than retrofit technologies in determining in-cabin air quality. The use of a HEPA air purifier removed up to 50% of in-cabin particles. Because each sub-study tested only a subset of the 24 school buses, the results should be seen as more exploratory than definitive.

Evaluation of critical indicators in the process of acquiring supplies and services LAC-UFPE

NASA Astrophysics Data System (ADS)

Caetano, V. F.; Ferreira, C. V.; dos Santos, M. J.; Honorato, F. A.

2015-01-01

In laboratories linked to public universities and accredited by the NBR ISO/IEC 17025, to meet efficiently item 4.6 (procurement of supplies and services) is a challenge that can be accomplished by programming based on historical purchases and services. In this study, we evaluated the critical procurement items to meet the quality management system of the LAC-UFPE: reagents, certified reference material, of equipment parts, maintenance and calibration of equipment and instruments. It was found that the most critical item is the certified reference material, the purchase or repair of which must be expedited within 125 days prior to the receipt to occur within the desired period.

Synthesis of zinc ultrafine powders via the Guen–Miller flow-levitation method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jigatch, A. N., E-mail: jan@chph.ras.ru; Leipunskii, I. O.; Kuskov, M. L.

2015-12-15

Zinc ultrafine powders (UFPs) with the average particle size of 0.175 to 1.24 μm are synthesized via the flow-levitation method. The peculiarities of the formation of zinc UFPs are considered with respect to the carrier gas properties (heat capacity, thermal conductivity, and diffusion coefficient), as well as the gas flow parameters (pressure and flow rate). The obtained zinc particles are studied via scanning electron microscopy and X-ray diffraction. The factors determining the crystal structure of zinc particles and their size distribution are discussed as well. The data on oxidation of zinc stored in unsealed containers under normal conditions are alsomore » presented.« less

Urban and rural ultrafine (PM 0.1) particles in the Helsinki area

NASA Astrophysics Data System (ADS)

Pakkanen, Tuomo A.; Kerminen, Veli-Matti; Korhonen, Christina H.; Hillamo, Risto E.; Aarnio, Päivi; Koskentalo, Tarja; Maenhaut, Willy

In June 1996-June 1997 Berner low-pressure impactors were used at an urban and at a rural site in the Helsinki area for sampling ultrafine particles (UFP, PM 0.1). Ten sample pairs, each pair measured simultaneously, were collected in the size range of 0.03-15 μm of particle aerodynamic diameter. More than 40 chemical components were measured. Surprisingly, the average UFP mass concentration was higher at the rural site (520 ng/m 3) than at the urban site (490 ng/m 3). The average chemical composition of UFP was similar at the two sites. The most abundant of the measured components were sulphate (32 and 40 ng/m 3 for the urban and rural sites, respectively), ammonium (22 and 25 ng/m 3), nitrate (4 and 11 ng/m 3) and the Ca 2+ ion (5 and 7 ng/m 3). The most important metals at both sites were Ca, Na, Fe, K and Zn with concentrations between 0.7 and 5 ng/m 3. Of the heavy metals, Ni, V, Cu, and Pb were important with average ultrafine concentrations between about 0.1 and 0.2 ng/m 3. Also the organic anions oxalate (urban 2.1 ng/m 3 and rural 1.9 ng/m 3) and methanesulphonate (1.3 and 1.7 ng/m 3) contributed similarly at both sites. The measured species accounted for only about 15-20% of the total ultrafine mass. The fraction that was not measured includes mainly carbonaceous material and water. It was estimated that the amount of water was about 10% (50 ng/m 3) and that of carbonaceous material about 70% (350 ng/m 3) at both sites. Aitken modes were observed for most components with the average mass mean mode diameters being between about 0.06 and 0.12 μm. The average concentrations in the Aitken mode differed clearly from those in the UFP for several components. The average contribution of ultrafine mass to the fine particle mass (PM 2.5) was about 7% at the urban site and 8.5% at the rural site. At both sites the contribution of ultrafine to fine was especially high for Se, Ag, B, and Ni (10-20%) and at the rural site also for Co (20%), Ca 2+ (16%) and Mo (11%). Enrichment in the ultrafine particles suggests that local sources may exist for these elements. Aitken modes turned out to be useful indicators of local sources for several components. The Aitken modes of Ba, Ca, Mg and Sr were similar in several samples, suggesting a common local combustion source for these elements, possibly traffic exhaust. Co, Fe, Mo and Ni formed another group of elements often having similar Aitken modes, the likely source being combustion of heavy fuel oil.

Determination of optimum parameters of the technological process for plates forming from V95 and V-1461 alloys in creep applied in aircrafts constructed by “Sukhoi design bureau”

NASA Astrophysics Data System (ADS)

Raevskaya, G. A.; Zakharchenko, K.; Larichkin, A.

2017-10-01

The research is devoted to the scientific justification of metal processing by pressure with the help of thick monolithic plates forming (thickness 40 mm) from the V95 (analog 7475) (Al-Zn-Mg-Cu) and V-1461 (analog 2099) (Al-Cu-Li-Zn) alloys in creep and close-to-superplasticity. Optimum parameters of the technological process of plate forming are described. The effect of temperature on the magnitude of mechanical stresses (relaxation) during the tests of materials on pure bending is experimentally determined. Forming of thick plates (40 mm) on the UFP-1M unit, and the control of the obtained surface, in comparison with the given electronic model, made it possible to experimentally determine the time and number of forming stages. Mechanical properties of the material after the technological process and heat treatment are preliminary evaluated. The efficiency of using the obtained parameters of the technological process and treatment of metals by pressure in such methods in general is shown.

Comparative In Vitro Biological Toxicity of Four Kinds of Air Pollution Particles.

PubMed

Shin, Han-Jae; Cho, Hyun Gi; Park, Chang Kyun; Park, Ki Hong; Lim, Heung Bin

2017-10-01

Accumulating epidemiological evidence indicates that exposure to fine air pollution particles (APPs) is associated with a variety of adverse health effects. However, the exact physiochemical properties and biological toxicities of fine APPs are still not well characterized. We collected four types of fine particle (FP) (diesel exhaust particles [DEPs], natural organic combustion [NOC] ash, synthetic organic combustion [SOC] ash, and yellow sand dust [YSD]) and investigated their physicochemical properties and in vitro biological toxicity. DEPs were almost entirely composed of ultrafine particles (UFPs), while the NOC, SOC, and YSD particles were a mixture of UFPs and FPs. The main elements in the DEPs, NOC ash, SOC ash, and YSD were black carbon, silicon, black carbon, and silicon, respectively. DEPs exhibited dose-dependent mutagenicity even at a low dose in Salmonella typhimurium TA 98 and 100 strains in an Ames test for genotoxicity. However, NOC, SOC, and YSD particles did not show any mutagenicity at high doses. The neutral red uptake assay to test cell viability revealed that DEPs showed dose-dependent potent cytotoxicity even at a low concentration. The toxicity of DEPs was relatively higher than that of NOC, SOC, and YSD particles. Therefore, these results indicate that among the four FPs, DEPs showed the highest in vitro biological toxicity. Additional comprehensive research studies such as chemical analysis and in vivo acute and chronic inhalation toxicity tests are necessary to determine and clarify the effects of this air contaminant on human health.

Desorption of SVOCs from Heated Surfaces in the Form of Ultrafine Particles.

PubMed

Wallace, Lance A; Ott, Wayne R; Weschler, Charles J; Lai, Alvin C K

2017-02-07

Ultrafine particles (UFP) produced by electric heating of stoves and metal cooking pans, absent food, have been hypothesized to be created from a surface film of semivolatile organic compounds (SVOCs) sorbed from the surrounding air. This study tests that hypothesis by size-resolved measurements extending the lower range of the UFP studied from 10 to 2.3 nm, and including other surfaces (glass, aluminum, and porcelain). Heating glass Petri dishes or squares of aluminum foil to about 350-400 °C for 4-6 min removed all sorbed organic substances completely. Subsequent exposure of these "clean" Petri dishes and foil squares to indoor air in two different residences for successively longer periods (1 h to 281 days), followed by heating the materials for 4-6 min, indicated a strong relationship of the number, size distribution, and mass of the UFP to the time exposed. Estimates of the accumulation rate of SVOCs on surfaces were similar to those in studies of organic film buildup on indoor windows. Transfer of skin oils by touching the glass or foil surfaces, or after washing the glass surface with detergent and bare hands, was also observed, with measured particle production comparable with that produced by long-term exposure to indoor air.

Where to locate transit stops: Cross-intersection profiles of ultrafine particles and implications for pedestrian exposure.

PubMed

Choi, Wonsik; Ranasinghe, Dilhara; DeShazo, J R; Kim, Jae-Jin; Paulson, Suzanne E

2018-02-01

Epidemiological studies have shown that exposure to traffic-related pollutants increases incidence of adverse health outcomes. Transit users in cities across the globe commonly spend 15-45 min or more waiting at transit stops each day, often at locations with high levels of pollution from traffic. Here, we investigate the characteristics of concentration profiles of ultrafine particles (UFP) with 5 m spatial resolution across intersections, to determine the best place to site transit stops to minimize exposures. Cross-intersection UFP profiles were derived from 1744 profiles covering 90 m before and after each intersection center with a mobile monitoring platform. Measurements were made at 10 signalized intersections located at six urban sites, each with a distinct built environment, during both mornings and afternoons. Measurements were made within 1.5 m of the sidewalk and approximately at breathing height (1.5 m above ground level) to approximate sidewalk exposures. UFP profiles were strongly influenced by high emissions from vehicle stops and accelerations, and peaked within 30 m of intersection centers; from there concentrations decreased sharply with distance. Peak concentrations averaged about 90% higher than the minima along the block. They were accompanied by more frequent and larger transient concentration spikes, increasing the chance of people near the intersection being exposed to both short-term extremely high concentration spikes and higher average concentrations. The decays are somewhat larger before the intersection than after the intersection, however as siting transit stops after intersections is preferred for smooth traffic flow, we focus on after the intersection. Simple time-duration exposure calculations combined with breathing rates suggest moving a bus stop from 20 to 40-50 m after the intersection can reduce transit-users' exposure levels to total UFP substantially, in proportion to the reciprocal of the magnitude of elevation at the intersection. Copyright © 2017 Elsevier Ltd. All rights reserved.

A CFD modeling study in an urban street canyon for ultrafine particles and population exposure: The intake fraction approach.

PubMed

Habilomatis, George; Chaloulakou, Archontoula

2015-10-15

Air quality in street canyons is of major importance, since the highest pollution levels are often encountered in these microenvironments. The canyon effect (reduced natural ventilation) makes them "hot spots" for particulate pollution contributing to adverse health effects for the exposed population. In this study we tried to characterize the influence of UFP (ultrafine particle) emissions from traffic on population exposure in an urban street canyon, by applying the intake fraction (iF) approach. One month long measurements of UFP levels have been monitored and used for the need of this study. We applied a three dimensional computational fluid dynamic (CFD) model based on real measurements for the simulation of UFP levels. We used infiltration factors, evaluated on a daily basis for the under study area, to estimate the indoor UFP levels. As a result the intake fraction for the pedestrians, residents and office workers is in the range of (1E-5)-(1E-4). The street canyon is mostly residential justifying partially the higher value of intake fraction for residents (1E-4). The above iF value is on the same order of magnitude with the corresponding one evaluated in a relative street canyon study. The total iF value in this microenvironment is one order of magnitude higher than ours, explained partially by the different use and activities. Two specific applications of iF to assess prioritization among emission sources and environmental justice issues are also examined. We ran a scenario with diesel and gasoline cars and diesel fueled vehicle seems to be a target source to improve overall iF. Our application focus on a small residential area, typical of urban central Athens, in order to evaluate high resolution iF. The significance of source-exposure relationship study in a micro scale is emphasized by recent research. Copyright © 2015 Elsevier B.V. All rights reserved.

Coarse and fine particles but not ultrafine particles in urban air trigger hospital admission for asthma in children.

PubMed

Iskandar, Amne; Andersen, Zorana Jovanovic; Bønnelykke, Klaus; Ellermann, Thomas; Andersen, Klaus Kaae; Bisgaard, Hans

2012-03-01

Short-term exposure to air pollution can trigger hospital admissions for asthma in children, but it is not known which components of air pollution are most important. There are no available studies on the particular effect of ultrafine particles (UFPs) on paediatric admissions for asthma. To study whether short-term exposure to air pollution is associated with hospital admissions for asthma in children. It is hypothesised that (1) the association between asthma admissions and air pollution is stronger with UFPs than with coarse (PM10) and fine (PM2.5) particles, nitrogen oxides (NOx) or nitrogen dioxide (NO2); and (2) infants are more susceptible to the effects of exposure to air pollution than older children. Daily counts of admissions for asthma in children aged 0-18 years to hospitals located within a 15 km radius of the central fixed background urban air pollution measurement station in Copenhagen between 2001 and 2008 were extracted from the Danish National Patient Registry. A time-stratified case crossover design was applied and data were analysed using conditional logistic regression to estimate the effect of air pollution on asthma admissions. A significant association was found between hospital admissions for asthma in children aged 0-18 years and NOx (OR 1.11; 95% CI 1.05 to 1.17), NO2 (1.10; 95% CI 1.04 to 1.16), PM10 (1.07; 95% CI 1.03 to 1.12) and PM2.5 (1.09; 95% CI 1.04 to 1.13); there was no association with UFPs. The association was stronger in infants than in older children for all pollutants, but no statistically significant interaction was detected. Short-term exposure to air pollution can trigger hospital admission for asthma in children, with infants possibly being most susceptible. These effects seemed to be mediated by larger particles and traffic-related gases, whereas UFPs showed no effect.

Spatial and temporal variation of sources contributing to quasi-ultrafine particulate matter PM0.36 in Augsburg, Germany.

PubMed

Li, Fengxia; Schnelle-Kreis, Jürgen; Cyrys, Josef; Wolf, Kathrin; Karg, Erwin; Gu, Jianwei; Orasche, Jürgen; Abbaszade, Gülcin; Peters, Annette; Zimmermann, Ralf

2018-08-01

to study the sources contributing to quasi-ultrafine particle (UFP) organic carbon and the spatial temporal variability of the sources. 24h quasi-UFP (particulate matter <0.36μm in this study) was sampled at a reference site continuously and at one of 5 other sites (T1, T2, T3, T4 and B1) in parallel in Augsburg, Germany from April 11th, 2014 to February 22nd, 2015, attempting to conduct 2-week campaigns at each site in 3 different seasons. Positive matrix factorization (PMF) was applied to measured organic tracers for source apportionment analyses. Pearson correlation coefficient r and coefficient of divergence (COD) were calculated to investigate spatial temporal variation of source contributions. 5 sources were identified comprising biomass burning (BB), traffic emissions (Traffic), biogenic secondary organic aerosol (bioSOA), isoprene originated secondary organic aerosol (isoSOA) and biomass burning related secondary organic aerosol (bbSOA). In general, good temporal correlation and uniform distribution within the study area are found for bioSOA and bbSOA, probably resulting from regional formation/transport. Lower temporal correlation and spatial heterogeneity of isoSOA were found at the city background site with local influence from green space and less traffic impact. BB demonstrated very good temporal correlation, but higher contributions at sites influenced by local residential heating emissions were observed. Traffic showed the least seasonality and lower correlation over time among the sources. However, it demonstrated low spatial heterogeneity of absolute contribution, and only a few days of elevated contribution was found at T3 when wind came directly from the street nearby. temporal correlation and spatial variability of sources contributing to the organic fraction of quasi-UFP vary among sites and source types and show source-specific characteristics. Therefore, caution should be taken when using one monitor site measurement to assess human exposure in health effect studies of quasi-UFP. Copyright © 2018 Elsevier B.V. All rights reserved.

Comparison of air pollution exposures in active vs. passive travel modes in European cities: A quantitative review.

PubMed

de Nazelle, Audrey; Bode, Olivier; Orjuela, Juan Pablo

2017-02-01

Transport microenvironments tend to have higher air pollutant concentrations than other settings most people encounter in their daily lives. The choice of travel modes may affect significantly individuals' exposures; however such considerations are typically not accounted for in exposure assessment used in environmental health studies. In particular, with increasing interest in the promotion of active travel, health impact studies that attempt to estimate potential adverse consequences of potential increased pollutant inhalation during walking or cycling have emerged. Such studies require a quantification of relative exposures in travel modes. The literature on air pollution exposures in travel microenvironments in Europe was reviewed. Studies which measured various travel modes including at least walking or cycling in a simultaneous or quasi-simultaneous design were selected. Data from these studies were harmonized to allow for a quantitative synthesis of the estimates. Ranges of ratios and 95% confidence interval (CI) of air pollution exposure between modes and between background and transportation modes were estimated. Ten studies measuring fine particulate matter (PM 2.5 ), black carbon (BC), ultrafine particles (UFP), and/or carbon monoxide (CO) in the walk, bicycle, car and/or bus modes were included in the analysis. Only three reported on CO and BC and results should be interpreted with caution. Pedestrians were shown to be the most consistently least exposed of all across studies, with the bus, bicycle and car modes on average 1.3 to 1.5 times higher for PM 2.5 ; 1.1 to 1.7 times higher for UFP; and 1.3 to 2.9 times higher for CO; however the 95% CI included 1 for the UFP walk to bus ratio. Only for BC were pedestrians more exposed than bus users on average (bus to walk ratio 0.8), but remained less exposed than those on bicycles or in cars. Car users tended to be the most exposed (from 2.9 times higher than pedestrians for BC down to similar exposures to cyclists for UFP on average). Bus exposures tended to be similar to that of cyclists (95% CI including 1 for PM 2.5 , CO and BC), except for UFP where they were lower (ratio 0.7). A quantitative method that synthesizes the literature on air pollution exposure in travel microenvironments for use in health impact assessments or potentially for epidemiology was conducted. Results relevant for the European context are presented, showing generally greatest exposures in car riders and lowest exposure in pedestrians. Copyright © 2017 Elsevier Ltd. All rights reserved.

The occurrence of ultrafine particles in the specific environment of children.

PubMed

Burtscher, Heinz; Schüepp, Karen

2012-06-01

Interest in ultrafine particles (UFP) has been increasing due to their specific physico-chemical characteristics. Ultrafine particles are those with an aerodynamic diameter of <0.1 μm and are also commonly know as nanoparticles (0.1 μm = 100 nm). Due to their small size UFP contribute mostly to particle number concentrations and are therefore underestimated in actual pollution measurements, which commonly measure mass concentration. Children represent the most vulnerable group in regard to particulate exposure due to their developing status and different exposures compared to adults. This review discusses the sources of ultrafine particles as well as the specific exposures of children highlighting the importance and uniqueness of this age group. Copyright © 2011 Elsevier Ltd. All rights reserved.

Ultrafine particle removal by residential heating, ventilating, and air-conditioning filters.

PubMed

Stephens, B; Siegel, J A

2013-12-01

This work uses an in situ filter test method to measure the size-resolved removal efficiency of indoor-generated ultrafine particles (approximately 7-100 nm) for six new commercially available filters installed in a recirculating heating, ventilating, and air-conditioning (HVAC) system in an unoccupied test house. The fibrous HVAC filters were previously rated by the manufacturers according to ASHRAE Standard 52.2 and ranged from shallow (2.5 cm) fiberglass panel filters (MERV 4) to deep-bed (12.7 cm) electrostatically charged synthetic media filters (MERV 16). Measured removal efficiency ranged from 0 to 10% for most ultrafine particles (UFP) sizes with the lowest rated filters (MERV 4 and 6) to 60-80% for most UFP sizes with the highest rated filter (MERV 16). The deeper bed filters generally achieved higher removal efficiencies than the panel filters, while maintaining a low pressure drop and higher airflow rate in the operating HVAC system. Assuming constant efficiency, a modeling effort using these measured values for new filters and other inputs from real buildings shows that MERV 13-16 filters could reduce the indoor proportion of outdoor UFPs (in the absence of indoor sources) by as much as a factor of 2-3 in a typical single-family residence relative to the lowest efficiency filters, depending in part on particle size. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments.

PubMed

Azimi, Parham; Zhao, Dan; Pouzet, Claire; Crain, Neil E; Stephens, Brent

2016-02-02

Previous research has shown that desktop 3D printers can emit large numbers of ultrafine particles (UFPs, particles less than 100 nm) and some hazardous volatile organic compounds (VOCs) during printing, although very few filament and 3D printer combinations have been tested to date. Here we quantify emissions of UFPs and speciated VOCs from five commercially available filament extrusion desktop 3D printers utilizing up to nine different filaments by controlled experiments in a test chamber. Median estimates of time-varying UFP emission rates ranged from ∼10(8) to ∼10(11) min(-1) across all tested combinations, varying primarily by filament material and, to a lesser extent, bed temperature. The individual VOCs emitted in the largest quantities included caprolactam from nylon-based and imitation wood and brick filaments (ranging from ∼2 to ∼180 μg/min), styrene from acrylonitrile butadiene styrene (ABS) and high-impact polystyrene (HIPS) filaments (ranging from ∼10 to ∼110 μg/min), and lactide from polylactic acid (PLA) filaments (ranging from ∼4 to ∼5 μg/min). Results from a screening analysis of potential exposure to these products in a typical small office environment suggest caution should be used when operating many of the printer and filament combinations in poorly ventilated spaces or without the aid of combined gas and particle filtration systems.

Emissions of particulate-bound elements from biodiesel and ultra low sulfur diesel: size distribution and risk assessment.

PubMed

Betha, Raghu; Balasubramanian, Rajasekhar

2013-01-01

Use of waste cooking oil derived biodiesel (WCOB) as an alternative fuel in diesel engines has increased significantly in recent years. The impact of WCOB on particulate emissions from diesel engines needs to be investigated thoroughly. This study was conducted to make a comparative evaluation and size-differentiated speciation of the particulate bound elements from ultra low sulfur diesel (ULSD) and WCOB and a blend of both of the fuels (B50). Particle mass and their elemental size distributions ranging from 0.01-5.6 μm were measured. It was observed that more ultrafine particles (UFPs, <100 nm) were emitted when the engine was fueled with WCOB. Fifteen particulate-bound elements such as K, Al, Mg, Co, Cr, Cu, Fe, Mn, Cd, Ni, As, Ba, Pb, Zn and Sr were investigated and reported in this study. Potential health risk associated with these particulate bound elements upon inhalation was also evaluated based on dose-response assessments for both adults and children. The findings indicate that the exposure to PM of the B100 exhaust is relatively more hazardous and may pose adverse health effects compared to that of ULSD. Also, investigations on human health risk due to exposure to UFPs indicate that UFPs contribute a major fraction (>70%) of the total estimated health risk. Copyright © 2012 Elsevier Ltd. All rights reserved.

A Randomized Cross-over Air Filtration Intervention Trial for Reducing Cardiovascular Health Risks in Residents of Public Housing near a Highway

PubMed Central

Padró-Martínez, Luz T.; Owusu, Emmanuel; Reisner, Ellen; Zamore, Wig; Simon, Matthew C.; Mwamburi, Mkaya; Brown, Carrie A.; Chung, Mei; Brugge, Doug; Durant, John L.

2015-01-01

Exposure to traffic-generated ultrafine particles (UFP; particles <100 nm) is likely a risk factor for cardiovascular disease. We conducted a trial of high-efficiency particulate arrestance (HEPA) filtration in public housing near a highway. Twenty residents in 19 apartments living <200 m from the highway participated in a randomized, double-blind crossover trial. A HEPA filter unit and a particle counter (measuring particle number concentration (PNC), a proxy for UFP) were installed in living rooms. Participants were exposed to filtered air for 21 days and unfiltered air for 21 days. Blood samples were collected and blood pressure measured at days 0, 21 and 42 after a 12-hour fasting period. Plasma was analyzed for high sensitivity C-reactive protein (hsCRP), interleukin-6 (IL-6), tumor necrosis factor alpha-receptor II (TNF-RII) and fibrinogen. PNC reductions ranging from 21% to 68% were recorded in 15 of the apartments. We observed no significant differences in blood pressure or three of the four biomarkers (hsCRP, fibrinogen, and TNF-RII) measured in participants after 21-day exposure to HEPA-filtered air compared to measurements after 21-day exposure to sham-filtered air. In contrast, IL-6 concentrations were significantly higher following HEPA filtration (0.668 pg/mL; CI = 0.465–0.959) compared to sham filtration. Likewise, PNC adjusted for time activity were associated with increasing IL-6 in 14- and 21-day moving averages, and PNC was associated with decreasing blood pressure in Lags 0, 1 and 2, and in a 3-day moving average. These negative associations were unexpected and could be due to a combination of factors including exposure misclassification, unsuccessful randomization (i.e., IL-6 and use of anti-inflammatory medicines), or uncontrolled confounding. Studies with greater reduction in UFP levels and larger sample sizes are needed. There also needs to be more complete assessment of resident time activity and of outdoor vs. indoor source contributions to UFP exposure. HEPA filtration remains a promising, but not fully realized intervention. PMID:26184257

Factors influencing variability in the infiltration of PM2.5 mass and its components

NASA Astrophysics Data System (ADS)

MacNeill, M.; Wallace, L.; Kearney, J.; Allen, R. W.; Van Ryswyk, K.; Judek, S.; Xu, X.; Wheeler, A.

2012-12-01

The infiltration of particles into homes can vary seasonally, between homes in a community and between communities. However, few studies have examined the day to day variability across multiple homes. We used continuous data collected from a 2-year (2005-2006) personal exposure study conducted in Windsor, ON to estimate daily infiltration factors (Finf) for fine particulate matter (PM2.5), Black Carbon (BC), and ultrafine particles (UFP) as well as the ambient personal exposure factor (Fpex) for PM2.5. In addition, the daily ambient and non-ambient generated components of indoor and personal concentrations were estimated. Median daily Finf estimates ranged from 0.26 to 0.36 across seasons for PM2.5; from 0.28 to 0.59 for BC; and from 0.15 to 0.26 for UFP. Median daily Fpex estimates ranged from 0.24 to 0.31 across seasons. Daily PM2.5 and UFP Finf and Fpex estimates were higher in summer than winter, although BC showed the opposite trend. Predictors of daily infiltration were typically related to window-opening behaviours, air conditioning, meteorological variables, and home age. In addition, use of electrostatic precipitators and stand alone air cleaners was associated with significantly reduced infiltration factors, indicating that these devices may provide a cost effective mechanism of reducing human exposures to particles of ambient origin. The majority of indoor PM2.5 (median 57-73%) and indoor BC (median 90-100%) was of ambient origin across seasons, while both personal PM2.5 and indoor UFPs had significant non-ambient contributions (median 60-65%). Factors that were found to increase non-ambient particle concentrations were typically related to cooking, candle use, supplemental heating, cleaning, and number of people in the home. Factors that were found to decrease non-ambient particle concentrations were open windows, and air cleaner use. This work has several implications to both epidemiologic studies and risk management. A better understanding of the factors influencing Finf and Fpex can improve exposure assessment and contribute to reduced exposure misclassification in epidemiologic studies. Furthermore, by increasing our knowledge of non-ambient and ambient exposures, risk associated with PM exposure can be managed more effectively.

Longitudinal associations of long-term exposure to ultrafine particles with blood pressure and systemic inflammation in Puerto Rican adults.

PubMed

Corlin, Laura; Woodin, Mark; Hart, Jaime E; Simon, Matthew C; Gute, David M; Stowell, Joanna; Tucker, Katherine L; Durant, John L; Brugge, Doug

2018-04-05

Few longitudinal studies have examined the association between ultrafine particulate matter (UFP, particles < 0.1 μm aerodynamic diameter) exposure and cardiovascular disease (CVD) risk factors. We used data from 791 adults participating in the longitudinal Boston Puerto Rican Health Study (Massachusetts, USA) between 2004 and 2015 to assess whether UFP exposure was associated with blood pressure and high sensitivity C-reactive protein (hsCRP, a biomarker of systemic inflammation). Residential annual average UFP exposure (measured as particle number concentration, PNC) was assigned using a model accounting for spatial and temporal trends. We also adjusted PNC values for participants' inhalation rate to obtain the particle inhalation rate (PIR) as a secondary exposure measure. Multilevel linear models with a random intercept for each participant were used to examine the association of UFP with blood pressure and hsCRP. Overall, in adjusted models, an inter-quartile range increase in PNC was associated with increased hsCRP (β = 6.8; 95% CI = - 0.3, 14.0%) but not with increased systolic blood pressure (β = 0.96; 95% CI = - 0.33, 2.25 mmHg), pulse pressure (β = 0.70; 95% CI = - 0.27, 1.67 mmHg), or diastolic blood pressure (β = 0.55; 95% CI = - 0.20, 1.30 mmHg). There were generally stronger positive associations among women and never smokers. Among men, there were inverse associations of PNC with systolic blood pressure and pulse pressure. In contrast to the primary findings, an inter-quartile range increase in the PIR was positively associated with systolic blood pressure (β = 1.03; 95% CI = 0.00, 2.06 mmHg) and diastolic blood pressure (β = 1.01; 95% CI = 0.36, 1.66 mmHg), but not with pulse pressure or hsCRP. We observed that exposure to PNC was associated with increases in measures of CVD risk markers, especially among certain sub-populations. The exploratory PIR exposure metric should be further developed.

Development of land-use regression models for exposure assessment to ultrafine particles in Rome, Italy

NASA Astrophysics Data System (ADS)

Cattani, Giorgio; Gaeta, Alessandra; di Menno di Bucchianico, Alessandro; de Santis, Antonella; Gaddi, Raffaela; Cusano, Mariacarmela; Ancona, Carla; Badaloni, Chiara; Forastiere, Francesco; Gariazzo, Claudio; Sozzi, Roberto; Inglessis, Marco; Silibello, Camillo; Salvatori, Elisabetta; Manes, Fausto; Cesaroni, Giulia; The Viias Study Group

2017-05-01

The health effects of long-term exposure to ultrafine particles (UFPs) are poorly understood. Data on spatial contrasts in ambient ultrafine particles (UFPs) concentrations are needed with fine resolution. This study aimed to assess the spatial variability of total particle number concentrations (PNC, a proxy for UFPs) in the city of Rome, Italy, using land use regression (LUR) models, and the correspondent exposure of population here living. PNC were measured using condensation particle counters at the building facade of 28 homes throughout the city. Three 7-day monitoring periods were carried out during cold, warm and intermediate seasons. Geographic Information System predictor variables, with buffers of varying size, were evaluated to model spatial variations of PNC. A stepwise forward selection procedure was used to develop a "base" linear regression model according to the European Study of Cohorts for Air Pollution Effects project methodology. Other variables were then included in more enhanced models and their capability of improving model performance was evaluated. Four LUR models were developed. Local variation in UFPs in the study area can be largely explained by the ratio of traffic intensity and distance to the nearest major road. The best model (adjusted R2 = 0.71; root mean square error = ±1,572 particles/cm³, leave one out cross validated R2 = 0.68) was achieved by regressing building and street configuration variables against residual from the "base" model, which added 3% more to the total variance explained. Urban green and population density in a 5,000 m buffer around each home were also relevant predictors. The spatial contrast in ambient PNC across the large conurbation of Rome, was successfully assessed. The average exposure of subjects living in the study area was 16,006 particles/cm³ (SD 2165 particles/cm³, range: 11,075-28,632 particles/cm³). A total of 203,886 subjects (16%) lives in Rome within 50 m from a high traffic road and they experience the highest exposure levels (18,229 particles/cm³). The results will be used to estimate the long-term health effects of ultrafine particle exposure of participants in Rome.

Release of ultrafine particles from three simulated building processes

NASA Astrophysics Data System (ADS)

Kumar, Prashant; Mulheron, Mike; Som, Claudia

2012-03-01

Building activities are recognised to produce coarse particulate matter but less is known about the release of airborne ultrafine particles (UFPs; those below 100 nm in diameter). For the first time, this study has investigated the release of particles in the 5-560 nm range from three simulated building activities: the crushing of concrete cubes, the demolition of old concrete slabs, and the recycling of concrete debris. A fast response differential mobility spectrometer (Cambustion DMS50) was used to measure particle number concentrations (PNC) and size distributions (PNDs) at a sampling frequency of 10 Hz in a confined laboratory room providing controlled environment and near-steady background PNCs. The sampling point was intentionally kept close to the test samples so that the release of new UFPs during these simulated processes can be quantified. Tri-modal particle size distributions were recorded for all cases, demonstrating different peak diameters in fresh nuclei (<10 nm), nucleation (10-30 nm) and accumulation (30-300 nm) modes for individual activities. The measured background size distributions showed modal peaks at about 13 and 49 nm with average background PNCs 1.47 × 104 cm-3. These background modal peaks shifted towards the larger sizes during the work periods (i.e. actual experiments) and the total PNCs increased between 2 and 17 times over the background PNCs for different activities. After adjusting for background concentrations, the net release of PNCs during cube crushing, slab demolition, and `dry' and `wet' recycling events were measured as 0.77, 19.1, 22.7 and 1.76 (×104) cm-3, respectively. The PNDs were converted into particle mass concentrations (PMCs). While majority of new PNC release was below 100 nm (i.e. UFPs), the bulk of new PMC emissions were constituted by the particles over 100 nm; 95, 79, 73 and 90% of total PNCs, and 71, 92, 93 and 91% of total PMCs, for cube crushing, slab demolition, dry recycling and wet recycling, respectively. The results of this study firmly elucidate the release of UFPs and raise a need for further detailed studies and designing health and safety related exposure guidelines for laboratory workplaces and operational building sites.

A Randomized Cross-over Air Filtration Intervention Trial for Reducing Cardiovascular Health Risks in Residents of Public Housing near a Highway.

PubMed

Padró-Martínez, Luz T; Owusu, Emmanuel; Reisner, Ellen; Zamore, Wig; Simon, Matthew C; Mwamburi, Mkaya; Brown, Carrie A; Chung, Mei; Brugge, Doug; Durant, John L

2015-07-10

Exposure to traffic-generated ultrafine particles (UFP; particles <100 nm) is likely a risk factor for cardiovascular disease. We conducted a trial of high-efficiency particulate arrestance (HEPA) filtration in public housing near a highway. Twenty residents in 19 apartments living <200 m from the highway participated in a randomized, double-blind crossover trial. A HEPA filter unit and a particle counter (measuring particle number concentration (PNC), a proxy for UFP) were installed in living rooms. Participants were exposed to filtered air for 21 days and unfiltered air for 21 days. Blood samples were collected and blood pressure measured at days 0, 21 and 42 after a 12-hour fasting period. Plasma was analyzed for high sensitivity C-reactive protein (hsCRP), interleukin-6 (IL-6), tumor necrosis factor alpha-receptor II (TNF-RII) and fibrinogen. PNC reductions ranging from 21% to 68% were recorded in 15 of the apartments. We observed no significant differences in blood pressure or three of the four biomarkers (hsCRP, fibrinogen, and TNF-RII) measured in participants after 21-day exposure to HEPA-filtered air compared to measurements after 21-day exposure to sham-filtered air. In contrast, IL-6 concentrations were significantly higher following HEPA filtration (0.668 pg/mL; CI = 0.465-0.959) compared to sham filtration. Likewise, PNC adjusted for time activity were associated with increasing IL-6 in 14- and 21-day moving averages, and PNC was associated with decreasing blood pressure in Lags 0, 1 and 2, and in a 3-day moving average. These negative associations were unexpected and could be due to a combination of factors including exposure misclassification, unsuccessful randomization (i.e., IL-6 and use of anti-inflammatory medicines), or uncontrolled confounding. Studies with greater reduction in UFP levels and larger sample sizes are needed. There also needs to be more complete assessment of resident time activity and of outdoor vs. indoor source contributions to UFP exposure. HEPA filtration remains a promising, but not fully realized intervention.

Ambient and Controlled Particle Exposures as Triggers for Acute ECG Changes.

PubMed

Rich, David Q; Peters, Annette; Schneider, Alexandra; Zareba, Wojciech; Breitner, Susanne; Oakes, David; Wiltshire, Jelani; Kane, Cathleen; Frampton, Mark W; Hampel, Regina; Hopke, Philip K; Cyrys, Josef; Utell, Mark J

2016-05-01

Previous studies have examined changes in heart rate variability (HRV*) and repolarization associated with increased particulate matter (PM) concentrations on the same and previous few days. However, few studies have examined whether these health responses to PM occur within a few hours or even less. Moreover, it is not clear whether exposure of subjects to ambient or-controlled PM concentrations both lead to similar health effects or whether any of the subjects' individual characteristics modify any of their responses to PM. The aims of the cur- rent study were to investigate whether exposure to PM was associated with rapid changes (< 60 minutes or con- current hour up to a delay of 6 hours) in markers of car- diac rhythni or changes in total antioxidant capacity (a marker of protection against oxidative stress) and whether any PM effects on cardiac rhythm markers were modified by total antioxidant capacity, age, obesity, smoking, hypertension, exertion, prior myocardial infarction (MI), or medication. We obtained data from a completed study in Augsburg, Germany (a panel study in N= 109 subjects, including a group with type 2 diabetes or impaired glucose tolerance [IGT; also known as prediabetes]) and a group of other- wise healthy subjects with a potential genetic susceptibil- ity to detoxifying and inflammatory pathways (Hampel et al. 2012b), as well as three completed studies in Rochester, New York (the REHAB panel study of N= 76 postinfarction patients in a cardiac rehabilitation pro- gram [Rich et al. 2012b]; the UPDIABETES study of con- trolled exposure to ultrafine particles [UFPs, particles with an aerodynamic diameter < 100 nm] of N = 19 patients with type 2 diabetes [Stewart et al. 2010; Vora et al. 2014j; and the UPCON controlled-exposure study of concentrated UFP exposure in N = 20 young, healthy, life- time nonsmokers). Data included 5-minute and 1-hour values for HRV and repolarization parameters from elec- trocardiogram (ECG) recordings and total antioxidant capacity measured in stored blood samples. Ambient con- centrations of UFPs, accumulation-mode particles (AMP, particles with an aerodynamic diameter of 100-500 nm), fine PM (PM2.5, particles with an aerodynamic diameter 2.5 pm), and black carbon (BC) were also available. We first conducted factor analyses in each study to find subgroups of correlated ECG outcomes and to reduce the number of outcomes examined in our statistical models. We then restricted the statistical analyses to the factors and representative.outcomes that were common to all four studies, including total HRV (measured as the standard deviation of normal-to-normal [NN] beat intervals [SDNNj), parasympathetic modulation (measured as the root mean square of the successive differences [RMSSD between adjacent NN beat intervals), and T-wave morphol- ogy (measured as T-wave complexity). Next, we used addi- tive mixed models to estimate the change in each outcome associated with increased pollutant concentrations in the . concurrent and previous 6 hours and with 5-minute inter- vals up to the previous 60 minutes, accounting for the correlation of repeated outcome measures for each subject and adjusting for time trend, hour of the day, temperature, relative humidity, day of the week, month, and visit number. Because multiple comparisons were an issue in our. analyses, we used a discovery-and-replication approach to draw conclusions across studies for each research question. In the Augsburg study, interquartile range (IQR) increases in UFP concentrations lagged 2 to 5 hours were associated with 1%-3% decreases in SDNN (e.g., lagged 3 hours in the group with a genetic susceptibility: -2.26%; 95% confidence interval [CI], -3.98% to -0.53%). In the REHAB study, similarly, IQR increases in UFP concentra- tions in the previous 5 hours were associated with < 3% decreases in SDNN (e.g., lagged 1 hour: -2.69%; 95% CI, -5.13% to -0.26%). We also found decreases in SDNN associated with IQR increases in total particle count-(a surrogate for UFP) in the UPDIABETES study (lagged 1 hour: -13.22%; 95% CI, -24.11% to -2.33%) but not in the UPCON study. In the Augsburg study, IQR increases in PM2.5 concen- trations in the concurrent hour and lagged 1-5 hours, AMP concentrations lagged 1 and 3 hours, and BC con- centrations lagged 1-5 hours were associated with -1%-5% decreases in SDNN (e.g., PM2.5 lagged 2 hours in the group with diabetes or IGT: -4.59%; 95% CI, -7.44% to -1.75%). In the REHAB study, IQR increases in PM2.5 concentrations lagged 5 and 6 hours and AMP concentra- tions in the concurrent hour and lagged up to 5 hours were associated with 1%-2% decreases in SDNN (e.g., PM2.5 lagged 4 hours: -2.13%; 95% CI, -3.91% to -0.35%). In the Augsburg study, IQR increases in PM2.5 concen- trations in the concurrent hour and BC lagged 1 and 6 hours were associated with 3%-7% decreases in RMSSD (e.g., PM2.5 concurrent hour in the group with diabetes or IGT: -7.20%; 95% CI, -12.11% to -2.02%). In the REHAB study, similarly, increases in PM2.5 concen- trations lagged 4 to 6 hours-though not AMP or BC con- centrations at any lag hour-were associated with -2.5%-3.5% decreases in RMSSD (e.g., PM2.5 lagged 5 hours: -3.49%; 95% CI, -6.13% to -0.84%). We did not find consistent evidence of any pollutant effects on T-wave complexity in 1-hour recordings. For 5-minute record- ings, there was no consistent evidence of UFP effects on SDNN, RMSSD, or T-wave complexity at any 5-minute interval within 60 minutes. We further concluded that these replicated hourly effects of UFP and PM2.5 on short-term measures of SDNN and RMSSD generally did not differ between the groups in the studies (i.e., type 2 diabetes, pre-diabetes/IGT, post- infarction, and healthy subjects). Last, we found no con- sistent evidence of effects of any pollutant on total anti- oxidant capacity and no consistent evidence of modification of our PM2.5-outcome associations by any of the potential effect modifiers. Increased UFP concentrations were associated with decreased SDNN in both of the panel studies and one of the two controlled-exposure studies. We also found that decreased SDNN was associated with both increased PM2.5 and AMP concentrations in the previous 6 hours in the panel studies and that decreased RMSSD was associ- ated with increased PM2.5 concentrations in the previous 6 hours in the panel studies. We therefore concluded that the research questions were replicated. Our findings suggest that both UFPs and PM2.5 are associated with autonomic dysfunction within hours of exposure, which may in part. explain the previously reported risk of acute cardiovascular events associated with increased PM in the previous few hours. Despite the heterogeneity of the study populations,and protocols, our findings provided consistent evidence for the induction of rapid pathophysiological responses by UFPs and PM2.5- The absence of consistent associations between UFPs, PM2.5, and these outcomes when examining shorter time intervals indicates that the 5- to 60-minute responses may be less pronounced than the responses occurring within hours. However, the findings from the 5-minute intervals may have been affected by the variety of proto- cols and conditions from study to study as well as by the potential effects of underlying diseases (e.g., healthy indi- viduals versus individuals with diabetes or a recent cor- onary artery. event), physical activity, circadian rhythms, stress, and/or medications.

Ultrafine particle concentrations in and around idling school buses

NASA Astrophysics Data System (ADS)

Zhang, Qunfang; Fischer, Heidi J.; Weiss, Robert E.; Zhu, Yifang

2013-04-01

Unnecessary school bus idling increases children's exposure to diesel exhaust, but to what extent children are exposed to ultrafine particles (UFPs, diameter < 100 nm) in and around idling school buses remains unclear. This study employed nine school buses and simulated five scenarios by varying emissions source, wind direction, and window position. The purpose was to investigate the impact of idling on UFP number concentration and PM2.5 mass concentration inside and near school buses. Near the school buses, total particle number concentration increased sharply from engine off to engine on under all scenarios, by a factor of up to 26. The impact of idling on UFP number concentration inside the school buses depended on wind direction and window position: wind direction was important and statistically significant while the effect of window positions depended on wind direction. Under certain scenarios, idling increased in-cabin total particle number concentrations by a factor of up to 5.8, with the significant increase occurring in the size range of 10-30 nm. No significant change of in-cabin PM2.5 mass concentration was observed due to idling, regardless of wind direction and window position, indicating that PM2.5 is not a good indicator for primary diesel exhaust particle exposure. The deposition rates based on total particle number concentration inside school bus cabins varied between 1.5 and 5.0 h-1 across nine tested buses under natural convection conditions, lower than those of passenger cars but higher than those of indoor environments.

Emission of particulate matter from a desktop three-dimensional (3D) printer

PubMed Central

Yi, Jinghai; LeBouf, Ryan F.; Duling, Matthew G.; Nurkiewicz, Timothy; Chen, Bean T.; Schwegler-Berry, Diane; Virji, M. Abbas; Stefaniak, Aleksandr B.

2016-01-01

ABSTRACT Desktop three-dimensional (3D) printers are becoming commonplace in business offices, public libraries, university labs and classrooms, and even private homes; however, these settings are generally not designed for exposure control. Prior experience with a variety of office equipment devices such as laser printers that emit ultrafine particles (UFP) suggests the need to characterize 3D printer emissions to enable reliable risk assessment. The aim of this study was to examine factors that influence particulate emissions from 3D printers and characterize their physical properties to inform risk assessment. Emissions were evaluated in a 0.5-m3 chamber and in a small room (32.7 m3) using real-time instrumentation to measure particle number, size distribution, mass, and surface area. Factors evaluated included filament composition and color, as well as the manufacturer-provided printer emissions control technologies while printing an object. Filament type significantly influenced emissions, with acrylonitrile butadiene styrene (ABS) emitting larger particles than polylactic acid (PLA), which may have been the result of agglomeration. Geometric mean particle sizes and total particle (TP) number and mass emissions differed significantly among colors of a given filament type. Use of a cover on the printer reduced TP emissions by a factor of 2. Lung deposition calculations indicated a threefold higher PLA particle deposition in alveoli compared to ABS. Desktop 3D printers emit high levels of UFP, which are released into indoor environments where adequate ventilation may not be present to control emissions. Emissions in nonindustrial settings need to be reduced through the use of a hierarchy of controls, beginning with device design, followed by engineering controls (ventilation) and administrative controls such as choice of filament composition and color. PMID:27196745

Land use regression modeling of ultrafine particles, ozone, nitrogen oxides and markers of particulate matter pollution in Augsburg, Germany.

PubMed

Wolf, Kathrin; Cyrys, Josef; Harciníková, Tatiana; Gu, Jianwei; Kusch, Thomas; Hampel, Regina; Schneider, Alexandra; Peters, Annette

2017-02-01

Important health relevance has been suggested for ultrafine particles (UFP) and ozone, but studies on long-term effects are scarce, mainly due to the lack of appropriate spatial exposure models. We designed a measurement campaign to develop land use regression (LUR) models to predict the spatial variability focusing on particle number concentration (PNC) as indicator for UFP, ozone and several other air pollutants in the Augsburg region, Southern Germany. Three bi-weekly measurements of PNC, ozone, particulate matter (PM 10 , PM 2.5 ), soot (PM 2.5 abs) and nitrogen oxides (NO x , NO 2 ) were performed at 20 sites in 2014/15. Annual average concentration were calculated and temporally adjusted by measurements from a continuous background station. As geographic predictors we offered several traffic and land use variables, altitude, population and building density. Models were validated using leave-one-out cross-validation. Adjusted model explained variance (R 2 ) was high for PNC and ozone (0.89 and 0.88). Cross-validation adjusted R 2 was slightly lower (0.82 and 0.81) but still indicated a very good fit. LUR models for other pollutants performed well with adjusted R 2 between 0.68 (PM coarse ) and 0.94 (NO 2 ). Contrary to previous studies, ozone showed a moderate correlation with NO 2 (Pearson's r=-0.26). PNC was moderately correlated with ozone and PM 2.5 , but highly correlated with NO x (r=0.91). For PNC and NO x , LUR models comprised similar predictors and future epidemiological analyses evaluating health effects need to consider these similarities. Copyright © 2016 Elsevier B.V. All rights reserved.

PEP Run Report for Integrated Test A, Caustic Leaching in UFP-VSL-T01A, Oxidative Leaching in UFP-VSL-T02A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guzman-Leong, Consuelo E.; Bredt, Ofelia P.; Burns, Carolyn A.

2009-12-04

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed and constructed and operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes.”(a) The PEP, located in the Process Engineering Laboratory-West (PDLW) located in Richland, Washington, is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes.more » The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing.« less

Using portable particle sizing instrumentation to rapidly measure the penetration of fine and ultrafine particles in unoccupied residences.

PubMed

Zhao, H; Stephens, B

2017-01-01

Much of human exposure to particulate matter of outdoor origin occurs inside buildings, particularly in residences. The particle penetration factor through leaks in a building's exterior enclosure assembly is a key parameter that governs the infiltration of outdoor particles. However, experimental data for size-resolved particle penetration factors in real buildings, as well as penetration factors for fine particles less than 2.5 μm (PM 2.5 ) and ultrafine particles less than 100 nm (UFPs), remain limited, in part because of previous limitations in instrumentation and experimental methods. Here, we report on the development and application of a modified test method that utilizes portable particle sizing instrumentation to measure size-resolved infiltration factors and envelope penetration factors for 0.01-2.5 μm particles, which are then used to estimate penetration factors for integral measures of UFPs and PM 2.5 . Eleven replicate measurements were made in an unoccupied apartment unit in Chicago, IL to evaluate the accuracy and repeatability of the test procedure and solution methods. Mean estimates of size-resolved penetration factors ranged from 0.41 ± 0.14 to 0.73 ± 0.05 across the range of measured particle sizes, while mean estimates of penetration factors for integral measures of UFPs and PM 2.5 were 0.67 ± 0.05 and 0.73 ± 0.05, respectively. Average relative uncertainties for all particle sizes/classes were less than 20%. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Spatial-temporal variations of particle number concentrations between a busy street and the urban background

NASA Astrophysics Data System (ADS)

Dos Santos-Juusela, Vanessa; Petäjä, Tuukka; Kousa, Anu; Hämeri, Kaarle

2013-11-01

To estimate spatial-temporal variations of ultrafine particles (UFP) in Helsinki, we measured particle total number concentrations (PNC) continuously in a busy street and an urban background site for six months, using condensation particle counters (CPC). We also evaluated the effects of temperature, wind speed and wind direction on PNC, as well as the correlation between PNC and PM2.5, PM10 and black carbon (BC) at the street. We found that on weekdays, hourly median PNC were highly correlated with BC (r = 0.88), moderately correlated with PM2.5 (r = 0.59) and weakly correlated with PM10 (r = 0.22). Number concentrations at the street were inversely proportional to temperature and wind speed, and highly dependent on wind direction. The highest PNC occurred during northeastern winds while the lowest occurred during southwestern winds. As these wind directions are nearly perpendicular to the street axis, the formation of wind vortices may have influenced the dispersion of UFP in the site. Although the temporal correlation for PNC was moderately high between the sites (r = 0.71), the median concentration at the street was 3 times higher than the urban background levels. The results indicate that people living or passing by the busy street are exposed to UFP concentrations well above the urban background levels. Thus, the study suggests that urban microenvironments should be considered in epidemiological studies. In addition the results emphasize that regulations based solely on PM2.5 and PM10 concentrations may be insufficient for preventing the adverse health effects of airborne particles.

Characterizing local traffic contributions to particulate air pollution in street canyons using mobile monitoring techniques

NASA Astrophysics Data System (ADS)

Zwack, Leonard M.; Paciorek, Christopher J.; Spengler, John D.; Levy, Jonathan I.

2011-05-01

Traffic within urban street canyons can contribute significantly to ambient concentrations of particulate air pollution. In these settings, it is challenging to separate within-canyon source contributions from urban and regional background concentrations given the highly variable and complex emissions and dispersion characteristics. In this study, we used continuous mobile monitoring of traffic-related particulate air pollutants to assess the contribution to concentrations, above background, of traffic in the street canyons of midtown Manhattan. Concentrations of both ultrafine particles (UFP) and fine particles (PM 2.5) were measured at street level using portable instruments. Statistical modeling techniques accounting for autocorrelation were used to investigate the presence of spatial heterogeneity of pollutant concentrations as well as to quantify the contribution of within-canyon traffic sources. Measurements were also made within Central Park, to examine the impact of offsets from major roadways in this urban environment. On average, an approximate 11% increase in concentrations of UFP and 8% increase in concentrations of PM 2.5 over urban background was estimated during high-traffic periods in street canyons as opposed to low traffic periods. Estimates were 8% and 5%, respectively, after accounting for temporal autocorrelation. Within Central Park, concentrations were 40% higher than background (5% after accounting for temporal autocorrelation) within the first 100 m from the nearest roadway for UFP, with a smaller but statistically significant increase for PM 2.5. Our findings demonstrate the viability of a mobile monitoring protocol coupled with spatiotemporal modeling techniques in characterizing local source contributions in a setting with street canyons.

Impact of atmospheric particulate matter pollutants to IAQ of airport terminal buildings: A first field study at Tianjin Airport, China

NASA Astrophysics Data System (ADS)

Ren, Jianlin; Cao, Xiaodong; Liu, Junjie

2018-04-01

Passengers usually spend hours in the airport terminal buildings waiting for their departure. During the long waiting period, ambient fine particles (PM2.5) and ultrafine particles (UFP) generated by airliners may penetrate into terminal buildings through open doors and the HVAC system. However, limited data are available on passenger exposure to particulate pollutants in terminal buildings. We conducted on-site measurements on PM2.5 and UFP concentration and the particle size distribution in the terminal building of Tianjin Airport, China during three different seasons. The results showed that the PM2.5 concentrations in the terminal building were considerably larger than the values guided by Chinese standard and WHO on all of the tested seasons, and the conditions were significantly affected by the outdoor air (Spearman test, p < 0.01). The indoor/outdoor PM2.5 ratios (I/O) ranged from 0.67 to 0.84 in the arrival hall and 0.79 to 0.96 in the departure hall. The particle number concentration in the terminal building presented a bi-modal size distribution, with one mode being at 30 nm and another mode at 100 nm. These results were totally different from the size distribution measured in a normal urban environment. The total UFP exposure during the whole waiting period (including in the terminal building and airliner cabin) of a passenger is approximately equivalent to 11 h of exposure to normal urban environments. This study is expected to contribute to the improvement of indoor air quality and health of passengers in airport terminal buildings.

Vascular effects of ultrafine particles in persons with type 2 diabetes

EPA Science Inventory

BACKGROUND: Diabetes confers an increased risk for cardiovascular effects of airborne particles. OBJECTIVE: We hypothesized that inhalation of elemental carbon ultrafine particles (UFP) would activate blood platelets and vascular endothelium in people with type 2 diabetes. ...

Exposure to ultrafine particles in different transport modes in the city of Rome.

PubMed

Grana, Mario; Toschi, Nicola; Vicentini, Laura; Pietroiusti, Antonio; Magrini, Andrea

2017-09-01

There is evidence of adverse health impacts from human exposure to particulate air pollution, including increased rates of respiratory and cardiovascular illness, hospitalizations, and pre-mature mortality. Most recent hypotheses assign an important role to ultrafine particles (UFP) (<0.1 μm) and to associated transition metals (in particular Fe). In a large city like Rome, where many active people spend more than one hour per day in private or public transportation, it may be important to evaluate the level of exposure to harmful pollutants which occurs during urban travelling. In this context, the aim of this work was to examine the relative contribution of different transport modes to total daily exposure. We performed experimental measurements during both morning and evening traffic peak hours throughout the winter season (December 2013-March 2014), for a total of 98 trips. Our results suggest that the lowest UFP exposures are experienced by underground train commuters, with an average number concentration of 14 134 cm -3 , and are largely a reflection of the routes being at greater distance from vehicular traffic. Motorcyclists experienced significantly higher average concentrations (73 168 cm -3 ) than all other exposure classes, and this is most likely a result of the presence of high-concentration and short-duration peaks which do not occur when the same routes are traveled by car. UFP concentrations in subway train environments were found to be comparable to urban background levels. Still, in underground trains we found the highest values of PM 10 mass concentration with a maximum value of 422 μg/m 3 . PM 10 concentration in trains was found to be four and two times higher than what was measured in car and motorbike trips, respectively. Transport mode contribution to total integrated UFP daily exposure was found to be 16.3%-20.9% while travelling by car, 28.7% for motorbike trips, and 8.7% for subway trips. Due to lower exposure times, commuting by car and motorbike is comparable to other daily activities in terms of exposure. Our data can provide relevant information for transport decision-making and increase environmental awareness in the hope that the information about inhaled pollutants can translate into a more rational approach to urban travelling. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ultrafine particles cause cytoskeletal dysfunctions in macrophages: role of intracellular calcium

PubMed Central

Möller, Winfried; Brown, David M; Kreyling, Wolfgang G; Stone, Vicki

2005-01-01

Background Particulate air pollution is reported to cause adverse health effects in susceptible individuals. Since most of these particles are derived form combustion processes, the primary composition product is carbon with a very small diameter (ultrafine, less than 100 nm in diameter). Besides the induction of reactive oxygen species and inflammation, ultrafine particles (UFP) can cause intracellular calcium transients and suppression of defense mechanisms of alveolar macrophages, such as impaired migration or phagocytosis. Methods In this study the role of intracellular calcium transients caused by UFP was studied on cytoskeleton related functions in J774A.1 macrophages. Different types of fine and ultrafine carbon black particles (CB and ufCB, respectively), such as elemental carbon (EC90), commercial carbon (Printex 90), diesel particulate matter (DEP) and urban dust (UD), were investigated. Phagosome transport mechanisms and mechanical cytoskeletal integrity were studied by cytomagnetometry and cell viability was studied by fluorescence microscopy. Macrophages were exposed in vitro with 100 and 320 μg UFP/ml/million cells for 4 hours in serum free medium. Calcium antagonists Verapamil, BAPTA-AM and W-7 were used to block calcium channels in the membrane, to chelate intracellular calcium or to inhibit the calmodulin signaling pathways, respectively. Results Impaired phagosome transport and increased cytoskeletal stiffness occurred at EC90 and P90 concentrations of 100 μg/ml/million cells and above, but not with DEP or UD. Verapamil and W-7, but not BAPTA-AM inhibited the cytoskeletal dysfunctions caused by EC90 or P90. Additionally the presence of 5% serum or 1% bovine serum albumin (BSA) suppressed the cytoskeletal dysfunctions. Cell viability showed similar results, where co-culture of ufCB together with Verapamil, W-7, FCS or BSA produced less cell dead compared to the particles only. PMID:16202162

[Distribution of atmospheric ultrafine particles during haze weather in Hangzhou].

PubMed

Chen, Qiu-Fang; Sun, Zai; Xie, Xiao-Fang

2014-08-01

Atmospheric ultrafine particles (UFPs) were monitored with fast mobility particle sizer (FMPS) in continuous haze weather and the haze fading process during December 6 to 11, 2013 in Hangzhou. Particle concentration and size distribution were studied associated with meteorological factors. The results showed that number concentrations were the highest at night and began to reduce in the morning. There was a small peak at 8 o'clock in the morning and 18 o'clock in the afternoon. It showed an obvious peak traffic source, which indicated that traffic emissions played a great role in the atmospheric pollution. During haze weather, the highest number concentration of UFPs reached 8 x 10(4) cm(-3). Particle size spectrum distribution was bimodal, the peak particle sizes were 15 nm and 100 nm respectively. Majority of UFPs were Aitken mode and Accumulation mode and the size of most particles concentrated near 100 nm. Average CMD(count medium diameter) was 85.89 nm. During haze fading process, number concentration and particles with size around 100 nm began to reduce and peak size shifted to small size. Nuclear modal particles increased and were more than accumulation mode. Average CMD was 58.64 nm. Meteorological factors such as the visibility and wind were negatively correlated with the particle number concentration. Correlation coefficient R were -0.225 and - 0.229. The humidity was correlated with number concentration. Correlation coefficient R was 0.271. The atmosphere was stable in winter and the level temperature had small correlation with number concentration. Therefore, study on distribution of atmospheric ultrafine particles during haze weather had the significance on the formation mechanism and control of haze weather.

Particle formation and growth at five rural and urban sites

NASA Astrophysics Data System (ADS)

Jeong, C.-H.; Evans, G. J.; McGuire, M. L.; Chang, R. Y.-W.; Abbatt, J. P. D.; Zeromskiene, K.; Mozurkewich, M.; Li, S.-M.; Leaitch, W. R.

2010-08-01

Ultrafine particle (UFP) number and size distributions were simultaneously measured at five urban and rural sites during the summer of 2007 in Ontario, Canada as part of the Border Air Quality and Meteorology Study (BAQS-Met 2007). Particle formation and growth events at these five sites were classified based on their strength and persistence as well as the variation in geometric mean diameter. Regional nucleation and growth events and local short-lived strong nucleation events were frequently observed at the near-border rural sites, upwind of industrial sources. Surprisingly, the particle number concentrations at one of these sites were higher than the concentrations at a downtown site in a major city, despite its high traffic density. Regional nucleation and growth events were favored during intense solar irradiance and in less polluted cooler drier air. The most distinctive regional particle nucleation and growth event during the campaign was observed simultaneously at all five sites, which were up to 350 km apart. Although the ultrafine particle concentrations and size distributions generally were spatially heterogeneous across the region, a more uniform spatial distribution of UFP across the five areas was observed during this regional nucleation event. Thus, nucleation events can cover large regions, contributing to the burden of UFP in cities and potentially to the associated health impacts on urban populations. Local short-lived nucleation events at the three near-border sites during this summer three-week campaign were associated with high SO2, which likely originated from US and Canadian industrial sources. Hence, particle formation in southwestern Ontario appears to often be related to anthropogenic gaseous emissions but biogenic emissions at times also contribute. Longer-term studies are needed to help resolve the relative contributions of anthropogenic and biogenic emissions to nucleation and growth in this region.

Exposure to Ultrafine Particles from Ambient Air and Oxidative Stress–Induced DNA Damage

PubMed Central

Bräuner, Elvira Vaclavik; Forchhammer, Lykke; Møller, Peter; Simonsen, Jacob; Glasius, Marianne; Wåhlin, Peter; Raaschou-Nielsen, Ole; Loft, Steffen

2007-01-01

Background Particulate matter, especially ultrafine particles (UFPs), may cause health effects through generation of oxidative stress, with resulting damage to DNA and other macromolecules. Objective We investigated oxidative damage to DNA and related repair capacity in peripheral blood mononuclear cells (PBMCs) during controlled exposure to urban air particles with assignment of number concentration (NC) to four size modes with average diameters of 12, 23, 57, and 212 nm. Design Twenty-nine healthy adults participated in a randomized, two-factor cross-over study with or without biking exercise for 180 min and with exposure to particles (NC 6169-15362/cm3) or filtered air (NC 91-542/cm3) for 24 hr. Methods The levels of DNA strand breaks (SBs), oxidized purines as formamidopyrimidine DNA glycolase (FPG) sites, and activity of 7,8-dihydro-8-oxoguanine-DNA glycosylase (OGG1) in PBMCs were measured by the Comet assay. mRNA levels of OGG1, nucleoside diphosphate linked moiety X-type motif 1 (NUDT1), and heme oxygenase-1 (HO1) were determined by real-time reverse transcriptase–polymerase chain reaction. Results Exposure to UFPs for 6 and 24 hr significantly increased the levels of SBs and FPG sites, with a further insignificant increase after physical exercise. The OGG1 activity and expression of OGG1, NUDT1, and HO1 were unaltered. There was a significant dose–response relationship between NC and DNA damage, with the 57-nm mode as the major contributor to effects. Concomitant exposure to ozone, nitrogen oxides, and carbon monoxide had no influence. Conclusion Our results indicate that UFPs, especially the 57-nm soot fraction from vehicle emissions, causes systemic oxidative stress with damage to DNA and no apparent compensatory up-regulation of DNA repair within 24 hr. PMID:17687444

Ultrafine Particle Metrics and Research Considerations: Review of the 2015 UFP Workshop.

PubMed

Baldauf, Richard W; Devlin, Robert B; Gehr, Peter; Giannelli, Robert; Hassett-Sipple, Beth; Jung, Heejung; Martini, Giorgio; McDonald, Joseph; Sacks, Jason D; Walker, Katherine

2016-10-28

In February 2015, the United States Environmental Protection Agency (EPA) sponsored a workshop in Research Triangle Park, NC, USA to review the current state of the science one missions, air quality impacts, and health effects associated with exposures to ultrafine particles[1].[...].

Ultrafine Particle Metrics and Research Considerations: Review of the 2015 UFP Workshop

EPA Science Inventory

In February 2015, the United States Environmental Protection Agency (EPA) sponsored a workshop in Research Triangle Park, North Carolina, USA to review the current state of the science on emissions, air quality impacts, and health effects associated with exposures to ultrafine pa...

Discontinuous and Continuous Indoor Air Quality Monitoring in Homes with Fireplaces or Wood Stoves as Heating System.

PubMed

de Gennaro, Gianluigi; Dambruoso, Paolo Rosario; Di Gilio, Alessia; Di Palma, Valerio; Marzocca, Annalisa; Tutino, Maria

2015-12-24

Around 50% of the world's population, particularly in developing countries, uses biomass as one of the most common fuels. Biomass combustion releases a considerable amount of various incomplete combustion products, including particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs). The paper presents the results of Indoor Air Quality (IAQ) measurements in six houses equipped with wood burning stoves or fireplaces as heating systems. The houses were monitored for 48-h periods in order to collect PM10 samples and measure PAH concentrations. The average, the maximum and the lowest values of the 12-h PM10 concentration were 68.6 μg/m³, 350.7 μg/m³ and 16.8 μg/m³ respectively. The average benzo[a]pyrene 12-h concentration was 9.4 ng/m³, while the maximum and the minimum values were 24.0 ng/m³ and 1.5 ng/m³, respectively. Continuous monitoring of PM10, PAHs, Ultra Fine Particle (UFP) and Total Volatile Organic Compounds (TVOC) was performed in order to study the progress of pollution phenomena due to biomass burning, their trends and contributions to IAQ. The results show a great heterogeneity of impacts on IAQ in terms of magnitude and behavior of the considered pollutants' concentrations. This variability is determined by not only different combustion technologies or biomass quality, but overall by different ignition mode, feeding and flame management, which can also be different for the same house. Moreover, room dimensions and ventilation were significant factors for pollution dispersion. The increase of PM10, UFP and PAH concentrations, during lighting, was always detected and relevant. Continuous monitoring allowed singling out contributions of other domestic sources of considered pollutants such as cooking and cigarettes. Cooking contribution produced an impact on IAQ in same cases higher than that of the biomass heating system.

The Effects of Vegetation Barriers on Near-road Ultrafine Particle Number and Carbon Monoxide Concentrations

EPA Science Inventory

Numerous studies have shown that people living in near-roadway communities (within 100 m of the road) are exposed to high ultrafine particle (UFP) number concentrations, which may be associated with adverse health effects. Vegetation barriers have been shown to affect pollutant t...

Impact of meteorology, traffic characteristics, and distance from roadway on roadside concentrations of ultrafine particulate matter

EPA Science Inventory

Traffic-laden roadways are major contributors to poor air quality in developed areas, elevating pollutants such as particulate matter (PM) and ozone. Among the numerous air pollutants emitted by vehicles, ultrafine particles (UFPs, diameter <100 nm) are of interest as a potentia...

Using mobile monitoring to visualise diurnal variation of traffic pollutants across two near-highway neighbourhoods

NASA Astrophysics Data System (ADS)

Pattinson, Woodrow; Longley, Ian; Kingham, Simon

2014-09-01

It is widely accepted that concentrations of primary traffic pollutants can vary substantially across relatively small urban areas. Fixed-site monitors have been shown to be largely inadequate for representing concentrations at nearby locations, resulting in the increasing use of spatial modelling or mobile sampling methods to achieve spatial saturation. In this study, we employ the use of a simple bicycle to sample concentrations of ultrafine particles (UFPs), carbon monoxide (CO) and particulate matter (PM10) at two small areas (<2.5 km2) in South Auckland, New Zealand. Portable instruments were mounted inside a custom-built casing at the front of the bicycle and every street within each study area was sampled in a grid-like fashion, at four times of day (07:00, 12:00, 17:00 and 22:00). Each area has a six-lane highway running through its centre and the core aim was to visualise and describe spatial variability of pollutant levels about the highway, main arterials and quieter streets, at periods of contrasting meteorological and traffic conditions. A total of 20 sampling runs in each area (five at each of the four timings) were conducted. Meteorological data were logged continuously at background sites within each study area. Results show that the influence of highway traffic (UFPs, CO) was strongest during the mornings and late evenings when wind speeds were low, while for the midday and afternoon timings, concentrations were highest at the arterial and shopping zones. Concentrations of PM10 appeared to be strongest in the residential areas during mornings and late evenings, suggesting an influence of wood burning for home heating. For all timings combined, for all three pollutants, it appears the arterial roads featuring shops and numerous intersections with traffic lights, had a stronger influence on concentrations than the busier but more free-flowing highways. This study provides not only an insight into microspatial hotspot variation across suburbs, but also how this variation shifts diurnally.

Air toxics exposure from vehicle emissions at a U.S. border crossing: Buffalo Peace Bridge Study.

PubMed

Spengler, John; Lwebuga-Mukasa, Jamson; Vallarino, Jose; Melly, Steve; Chillrud, Steve; Baker, Joel; Minegishi, Taeko

2011-07-01

The Peace Bridge in Buffalo, New York, which spans the Niagara River at the east end of Lake Erie, is one of the busiest U.S. border crossings. The Peace Bridge plaza on the U.S. side is a complex of roads, customs inspection areas, passport control areas, and duty-free shops. On average 5000 heavy-duty diesel trucks and 20,000 passenger cars traverse the border daily, making the plaza area a potential "hot spot" for emissions from mobile sources. In a series of winter and summer field campaigns, we measured air pollutants, including many compounds considered by the U.S. Environmental Protection Agency (EPA*) as mobile-source air toxics (MSATs), at three fixed sampling sites: on the shore of Lake Erie, approximately 500 m upwind (under predominant wind conditions) of the Peace Bridge plaza; immediately downwind of (adjacent to) the plaza; and 500 m farther downwind, into the community of west Buffalo. Pollutants sampled were particulate matter (PM) < or = 10 microm (PM10) and < or = 2.5 microm (PM2.5) in aerodynamic diameter, elemental carbon (EC), 28 elements, 25 volatile organic compounds (VOCs) including 3 carbonyls, 52 polycyclic aromatic hydrocarbons (PAHs), and 29 nitrogenated polycyclic aromatic hydrocarbons (NPAHs). Spatial patterns of counts of ultrafine particles (UFPs, particles < 0.1 microm in aerodynamic diameter) and of particle-bound PAH (pPAH) concentrations were assessed by mobile monitoring in the neighborhood adjacent to the Peace Bridge plaza using portable instruments and Global Positioning System (GPS) tracking. The study was designed to assess differences in upwind and downwind concentrations of MSATs, in areas near the Peace Bridge plaza on the U.S. side of the border. The Buffalo Peace Bridge Study featured good access to monitoring locations proximate to the plaza and in the community, which are downwind with the dominant winds from the direction of Lake Erie and southern Ontario. Samples from the lakeside Great Lakes Center (GLC), which is upwind of the plaza with dominant winds, were used to characterize contaminants in regional air masses. On-site meteorologic measurements and hourly truck and car counts were used to assess the role of traffic on UFP counts and pPAH concentrations. The array of parallel and perpendicular residential streets adjacent to the plaza provided a grid on which to plot the spatial patterns of UFP counts and pPAH concentrations to determine the extent to which traffic emissions from the Peace Bridge plaza might extend into the neighboring community. For lake-wind conditions (southwest to northwest) 12-hour integrated daytime samples showed clear evidence that vehicle-related emissions at the Peace Bridge plaza were responsible for elevated downwind concentrations of PM2.5, EC, and benzene, toluene, ethylbenzene, and xylenes (BTEX), as well as 1,3-butadiene and styrene. The chlorinated VOCs and aldehydes were not differentially higher at the downwind site. Several metals (aluminum, calcium, iron, copper, and antimony) were two times higher at the site adjacent to the plaza as they were at the upwind GLC site on lake-wind sampling days. Other metals (beryllium, sodium, magnesium, potassium, titanium, manganese, cobalt, strontium, tin, cesium, and lanthanum) showed significant increases downwind as well. Sulfur, arsenic, selenium, and a few other elements appeared to be markers for regional transport as their upwind and downwind concentrations were correlated, with ratios near unity. Using positive matrix factorization (PMF), we identified the sources for PAHs at the three fixed sampling sites as regional, diesel, general vehicle, and asphalt volatilization. Diesel exhaust at the Peace Bridge plaza accounted for approximately 30% of the PAHs. The NPAH sources were identified as nitrate (NO3) radical reactions, diesel, and mixed sources. Diesel exhaust at the Peace Bridge plaza accounted for 18% of the NPAHs. Further evidence for the impact of the Peace Bridge plaza on local air quality was found when the differences in 10-minute average UFP counts and pPAH concentrations were calculated between pairs of sites and displayed by wind direction. With winds from approximately 160 degrees through 220 degrees, UFP counts adjacent to the plaza were 10,000 to 20,000 particles/cm3 higher than those upwind of the plaza. A similar pattern was displayed for pPAH concentrations adjacent to the plaza, which were between 10 and 20 ng/m3 higher than those at the upwind GLC site. Regression models showed better correlation with traffic variables for pPAHs than for UFPs. For pPAHs, truck counts and car counts had significant positive correlations, with similar magnitudes for the effects of trucks and cars, despite lower truck counts. Examining all traffic variables, including traffic counts and counts divided by wind speed, the multivariate regression analysis had an adjusted coefficient of determination (R2) of 0.34 for pPAHs, with all terms significant at P < 0.002. Study staff members traversed established routes in the neighborhood while carrying instruments to record continuous UFP and pPAH values. They also carried a GPS, which was used to provide location-specific time-stamped data. Analyses using a geographic information system (GIS) demonstrated that emissions at the Peace Bridge plaza, at times, affected ambient air quality over several blocks (a few hundred meters). Under lake-wind conditions, overall spatial patterns in UFP and pPAH levels were similar for summer and winter and for morning and afternoon sampling sessions. The Buffalo Peace Bridge Study demonstrated that a concentration of motor vehicles resulted in elevated levels of mobile-source-related emissions downwind, to distances of 300 m to 600 m. The study provides a unique data set to assess interrelationships among MSATs and to ascertain the impact of heavy-duty diesel vehicles on air quality.

U.S. EPA, Pesticide Product Label, PARATHION EHTYL-METHYL 6-3, 04/21/1972

EPA Pesticide Factsheets

2011-04-21

... ', .. , nIl I' ~~nh~Ii". " .. 1'1. II'" 'flO: T,,, .. fiji[ 10':;\\1';' ""t' I I rAe 1/"'.I ~t~'. ~ ,Nl .. l' .. : Uf.p ... t •• , • 1"" .1('" I.·, l""'iM".'" "r,_ I., .,"II,d, .11'1'1, I,,,.! ...

Air quality impacts of a CicLAvia event in Downtown Los Angeles, CA.

PubMed

Shu, Shi; Batteate, Christina; Cole, Brian; Froines, John; Zhu, Yifang

2016-01-01

CicLAvia in Los Angeles, CA is the open streets program that closes streets to motorized vehicles and invites people to walk, run, play or ride their bicycles on these streets, allowing them to experience the city in a new way and get exercise at the same time. Since the events reduce the motorized traffic flow, which is a significant source of air pollution, on the streets, it is reasonable to hypothesize that the CicLAvia events can reduce the concentrations of traffic-emitted air pollutants during the road closure. This study is the first experiment to test this hypothesis. The on-road and community-wide ultrafine particle (UFP) and PM2.5 were measured on the Event-Sunday (October 5th, 2014) and the Pre- and Post- Sundays (September 28(th) and October 12(th), 2014). Data analysis results showed the on-road UFP and PM2.5 reduction was 21% and 49%, respectively, and the community-wide PM2.5 reduction was 12%. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ultrafine particles and platelet activation in patients with coronary heart disease – results from a prospective panel study

PubMed Central

Rückerl, Regina; Phipps, Richard P; Schneider, Alexandra; Frampton, Mark; Cyrys, Josef; Oberdörster, Günther; Wichmann, H Erich; Peters, Annette

2007-01-01

Background Epidemiological studies on health effects of air pollution have consistently shown adverse cardiovascular effects. Toxicological studies have provided evidence for thrombogenic effects of particles. A prospective panel study in a susceptible population was conducted in Erfurt, Germany, to study the effects of daily changes in ambient particles on various blood cells and soluble CD40ligand (sCD40L, also known as CD154), a marker for platelet activation that can cause increased coagulation and inflammation. Blood cells and plasma sCD40L levels were repeatedly measured in 57 male patients with coronary heart disease (CHD) during winter 2000/2001. Fixed effects linear regression models were applied, adjusting for trend, weekday and meteorological parameters. Hourly data on ultrafine particles (UFP, number concentration of particles from 0.01 to 0.1 μm), mass concentration of particles less than 10 and 2.5 μm in diameter (PM10, PM2.5), accumulation mode particle counts (AP, 0.1–1.0 μm), elemental and organic carbon, gaseous pollutants and meteorological data were collected at central monitoring sites. Results An immediate increase in plasma sCD40L was found in association with UFP and AP (% change from geometric mean: 7.1; CI: [0.1, 14.5] and 6.9; CI: [0.5, 13.8], respectively). Platelet counts decreased in association with UFP showing an immediate, a three days delayed (lag 3) and a 5-day average response (% change from the mean: -1.8; CI: [-3.4,-0.2]; -2.4; CI: [-4.5,-0.3] and -2.2; CI: [-4.0,-0.3] respectively). Conclusion The increased plasma sCD40L levels support the hypothesis that higher levels of ambient air pollution lead to an inflammatory response in patients with CHD thus providing a possible explanation for the observed association between air pollution and cardiovascular morbidity and mortality in susceptible parts of the population. PMID:17241467

Source apportionment of aerosol particles at a European air pollution hot spot using particle number size distributions and chemical composition.

PubMed

Leoni, Cecilia; Pokorná, Petra; Hovorka, Jan; Masiol, Mauro; Topinka, Jan; Zhao, Yongjing; Křůmal, Kamil; Cliff, Steven; Mikuška, Pavel; Hopke, Philip K

2018-03-01

Ostrava in the Moravian-Silesian region (Czech Republic) is a European air pollution hot spot for airborne particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), and ultrafine particles (UFPs). Air pollution source apportionment is essential for implementation of successful abatement strategies. UFPs or nanoparticles of diameter <100 nm exhibit the highest deposition efficiency in human lungs. To permit apportionment of PM sources at the hot-spot including nanoparticles, Positive Matrix Factorization (PMF) was applied to highly time resolved particle number size distributions (NSD, 14 nm-10 μm) and PM 0.09-1.15 chemical composition. Diurnal patterns, meteorological variables, gaseous pollutants, organic markers, and associations between the NSD factors and chemical composition factors were used to identify the pollution sources. The PMF on the NSD reveals two factors in the ultrafine size range: industrial UFPs (28%, number mode diameter - NMD 45 nm), industrial/fresh road traffic nanoparticles (26%, NMD 26 nm); three factors in the accumulation size range: urban background (24%, NMD 93 nm), coal burning (14%, volume mode diameter - VMD 0.5 μm), regional pollution (3%, VMD 0.8 μm) and one factor in the coarse size range: industrial coarse particles/road dust (2%, VMD 5 μm). The PMF analysis of PM 0.09-1.15 revealed four factors: SIA/CC/BB (52%), road dust (18%), sinter/steel (16%), iron production (16%). The factors in the ultrafine size range resolved with NSD have a positive correlation with sinter/steel production and iron production factors resolved with chemical composition. Coal combustion factor resolved with NSD has moderate correlation with SIA/CC/BB factor. The organic markers homohopanes correlate with coal combustion and the levoglucosan correlates with urban background. The PMF applications to NSD and chemical composition datasets are complementary. PAHs in PM 1 were found to be associated with coal combustion factor. Copyright © 2017 Elsevier Ltd. All rights reserved.

Traffic pollutant exposures experienced by pedestrians waiting to enter the U.S. at a major U.S.-Mexico border crossing

NASA Astrophysics Data System (ADS)

Galaviz, V. E.; Yost, M. G.; Simpson, C. D.; Camp, J. E.; Paulsen, M. H.; Elder, J. P.; Hoffman, L.; Flores, D.; Quintana, P. J. E.

2014-05-01

Pedestrians waiting to cross into the US from Mexico at Ports of Entry experience long wait times near idling vehicles. The near-road environment is associated with elevated pollutant levels and adverse health outcomes. This is the first exposure assessment conducted to quantify northbound pedestrian commuter exposure to traffic-related air pollutants at the U.S.-Mexico border San Ysidro Port of Entry (SYPOE). Seventy-three persons who regularly crossed the SYPOE in the pedestrian line and 18 persons who did not cross were recruited to wear personal air monitors for 24-h to measure traffic pollutants particulate matter less than 2.5 μm (PM2.5), 1-nitropyrene (1-NP) - a marker for diesel exhaust - and carbon monoxide (CO). Fixed site concentrations were collected at SYPOE and occurred during the time subjects were crossing northbound to approximate their exposure to 1-NP, ultrafine particles (UFP), PM2.5, CO, and black carbon (BC) while standing in line during their border wait. Subjects who crossed the border in pedestrian lanes had a 6-fold increase in exposure to 1-NP, a 3-fold increase in exposure to CO, and a 2-fold increase in exposure to gravimetric PM2.5, vs. non-border commuters. Univariate regression analysis for UFP (median 40,000 # cm-3) found that border wait time for vehicles explained 21% of variability and relative humidity 13%, but when modeled together neither predictor remained significant. Concentrations at the SYPOE of UFP, PM2.5, CO, and BC are similar to those in other near-roadway studies that show associations with acute and chronic adverse health effects. Although results are limited by small sample numbers, these findings warrant concern for adverse health effects experienced by pedestrian commuters waiting in a long northbound queue at SYPOE and demonstrates a potential health benefit of reduced wait times at the border.

Using models to interpret the impact of roadside barriers on near-road air quality

NASA Astrophysics Data System (ADS)

Amini, Seyedmorteza; Ahangar, Faraz Enayati; Schulte, Nico; Venkatram, Akula

2016-08-01

The question this paper addresses is whether semi-empirical dispersion models based on data from controlled wind tunnel and tracer experiments can describe data collected downwind of a sound barrier next to a real-world urban highway. Both models are based on the mixed wake model described in Schulte et al. (2014). The first neglects the effects of stability on dispersion, and the second accounts for reduced entrainment into the wake of the barrier under unstable conditions. The models were evaluated with data collected downwind of a kilometer-long barrier next to the I-215 freeway running next to the University of California campus in Riverside. The data included measurements of 1) ultrafine particle (UFP) concentrations at several distances from the barrier, 2) micrometeorological variables upwind and downwind of the barrier, and 3) traffic flow separated by automobiles and trucks. Because the emission factor for UFP is highly uncertain, we treated it as a model parameter whose value is obtained by fitting model estimates to observations of UFP concentrations measured at distances where the barrier impact is not dominant. Both models provide adequate descriptions of both the magnitude and the spatial variation of observed concentrations. The good performance of the models reinforces the conclusion from Schulte et al. (2014) that the presence of the barrier is equivalent to shifting the line sources on the road upwind by a distance of about HU/u∗ where H is the barrier height, U is the wind velocity at half of the barrier height, and u∗ is the friction velocity. The models predict that a 4 m barrier results in a 35% reduction in average concentration within 40 m (10 times the barrier height) of the barrier, relative to the no-barrier site. This concentration reduction is 55% if the barrier height is doubled.

Factors affecting pollutant concentrations in the near-road environment

NASA Astrophysics Data System (ADS)

Baldwin, Nichole; Gilani, Owais; Raja, Suresh; Batterman, Stuart; Ganguly, Rajiv; Hopke, Philip; Berrocal, Veronica; Robins, Thomas; Hoogterp, Sarah

2015-08-01

An improved understanding of traffic-related air pollutants is needed to estimate exposures and adverse health impacts in traffic corridors and near-road environments. In this study, concentrations of black carbon (BC), nitrogen oxides (NO, NO2, NOx), sulfur dioxide (SO2), and particulate matter (PM2.5, PM10, ultrafine particles, and accumulation mode particles, AMP) were measured using a mobile air pollutant laboratory along nine transects across major roads in Detroit, MI in winter 2012. Repeated measurements were taken during rush-hour periods at sites in residential neighborhoods located 50-500 m from both sides of the road. Concentration gradients attributable to on-road emissions were estimated by accounting for traffic volume and mix, wind speed, wind direction, and background concentrations. BC, NO, NOx, and UFP had the strongest gradients, and elevated concentrations of NOx, NO2, PM2.5 and PM10, as well as decreased particle size, were found at the 50 m sites compared to background levels. Exponential models incorporating effects of road size, wind speed, and up- and downwind distance explained from 31 to 53% of the variability in concentration gradients for BC, NO, NOx, UFP and particle size. The expected concentration increments 50 m from the study roads were 17.0 ppb for NO, 17.7 ppb for NOx, 2245 particles/cm3 for UFP, and 0.24 μg/m3 for BC, and the expected distance to decrease increments by half was 89-129 m in the downwind direction, and 14-20 m in the upwind direction. While accounting for portion of the temporal and spatial variability across transects and measurement periods, these results highlight the influence of road-to-road differences and other locally-varying factors important in urban and industrial settings. The study demonstrates a methodology to quantify near-road concentrations and influences on these concentrations while accounting for temporal and spatial variability, and it provides information useful for estimating exposures of traffic-related air pollutants in urban environments.

Concentration levels and source apportionment of ultrafine particles in road microenvironments

NASA Astrophysics Data System (ADS)

Argyropoulos, G.; Samara, C.; Voutsa, D.; Kouras, A.; Manoli, E.; Voliotis, A.; Tsakis, A.; Chasapidis, L.; Konstandopoulos, A.; Eleftheriadis, K.

2016-03-01

A mobile laboratory unit (MOBILAB) with on-board instrumentation (Scanning Mobility Particle Sizer, SMPS; Ambient NOx analyzer) was used to measure size-resolved particle number concentrations (PNCs) of quasi-ultrafine particles (UFPs, 9-372 nm), along with NOx, in road microenvironments. On-road measurements were carried out in and around a large Greek urban agglomeration, the Thessaloniki Metropolitan Area (TMA). Two 2-week measurement campaigns were conducted during the warm period of 2011 and the cold period of 2012. During each sampling campaign, MOBILAB was driven through a 5-day inner-city route and a second 5-day external route covering in total a wide range of districts (urban, urban background, industrial and residential), and road types (major and minor urban roads, freeways, arterial and interurban roads). All routes were conducted during working days, in morning and in afternoon hours under real-world traffic conditions. Spatial classification of MOBILAB measurements involved the assignment of measurement points to location bins defined by the aspect ratio of adjacent urban street canyons (USCs). Source apportionment was further carried out, by applying Positive Matrix Factorization (PMF) to particle size distribution data. Apportioned PMF factors were interpreted, by employing a two-step methodology, which involved (a) statistical association of PMF factor contributions with 12 h air-mass back-trajectories ending at the TMA during MOBILAB measurements, and (b) Multiple Linear Regression (MLR) using PMF factor contributions as the dependent variables, while relative humidity, solar radiation flux, and vehicle speed were used as the independent variables. The applied data analysis showed that low-speed cruise and high-load engine operation modes are the two dominant sources of UFPs in most of the road microenvironments in the TMA, with significant contributions from background photochemical processes during the warm period, explaining the reversed seasonal variation of UFP concentrations, compared to those observed in cities across Northern Europe. It was also demonstrated that town planning exerts a profound effect on the mitigation of traffic emissions.

Protein evaluation of four oat (Avena sativa L.) cultivars adapted for cultivation in the south of Brazil.

PubMed

Pedó, I; Sgarbieri, V C; Gutkoski, L C

1999-01-01

Four oat cultivars adapted for soil and climate conditions in the southern region of Brazil were evaluated for protein nutritive value. Evaluations were done both in vitro and in vivo. In vitro evaluation was done by essential amino acid profile, available lysine, amino acid scoring, and protein digestibility corrected amino acid-scoring (PDCAAS). Nitrogen balance indices and PER were determined in vivo with rats. In all four cultivars (UFP-15, UFP-16, CTC-03, UFRGS-14), lysine was the most limiting amino acid. Available lysine, amino acid score and PDCAAS were highest for cultivar UFRGS-14 and lowest for CTC-03. When compared to casein, only nitrogen retention for UFRGS-14 did not differ statistically (p>0.05); all other indices of protein quality were inferior to casein for the oat cultivars. The oat cultivars tended to be identical among themselves, except for apparent protein digestibility which was significantly higher in the UFRGS-14 and CTC-03 cultivars. On average, the PER values of the oat cultivars were 82% of casein; the net protein utilization was 88% of casein as determined in vivo and 49% by the estimation in vitro (PDCAAS).

[Ultrafine particle number concentration and size distribution of vehicle exhaust ultrafine particles].

PubMed

Lu, Ye-qiang; Chen, Qiu-fang; Sun, Zai; Cai, Zhi-liang; Yang, Wen-jun

2014-09-01

Ultrafine particle (UFP) number concentrations obtained from three different vehicles were measured using fast mobility particle sizer (FMPS) and automobile exhaust gas analyzer. UFP number concentration and size distribution were studied at different idle driving speeds. The results showed that at a low idle speed of 800 rmin-1 , the emission particle number concentration was the lowest and showed a increasing trend with the increase of idle speed. The majority of exhaust particles were in Nuclear mode and Aitken mode. The peak sizes were dominated by 10 nm and 50 nm. Particle number concentration showed a significantly sharp increase during the vehicle acceleration process, and was then kept stable when the speed was stable. In the range of 0. 4 m axial distance from the end of the exhaust pipe, the particle number concentration decayed rapidly after dilution, but it was not obvious in the range of 0. 4-1 m. The number concentration was larger than the background concentration. Concentration of exhaust emissions such as CO, HC and NO showed a reducing trend with the increase of idle speed,which was in contrast to the emission trend of particle number concentration.

Pedestrians in Traffic Environments: Ultrafine Particle Respiratory Doses

PubMed Central

Manigrasso, Maurizio; Natale, Claudio; Vitali, Matteo; Protano, Carmela; Avino, Pasquale

2017-01-01

Particulate matter has recently received more attention than other pollutants. PM10 and PM2.5 have been primarily monitored, whereas scientists are focusing their studies on finer granulometric sizes due both to their high number concentration and their high penetration efficiency into the respiratory system. The purpose of this study is to investigate the population exposure to UltraFine Particles (UFP, submicrons in general) in outdoor environments. The particle number doses deposited into the respiratory system have been compared between healthy individuals and persons affected by Chronic Obstructive Pulmonary Disease (COPD). Measurements were performed by means of Dust Track and Nanoscan analyzers. Forty minute walking trails through areas with different traffic densities in downtown Rome have been considered. Furthermore, particle respiratory doses have been estimated for persons waiting at a bus stop, near a traffic light, or along a high-traffic road, as currently occurs in a big city. Large differences have been observed between workdays and weekdays: on workdays, UFP number concentrations are much higher due to the strong contribution of vehicular exhausts. COPD-affected individuals receive greater doses than healthy individuals due to their higher respiratory rate. PMID:28282961

Exposure to ultrafine particles in hospitality venues with partial smoking bans.

PubMed

Neuberger, Manfred; Moshammer, Hanns; Schietz, Armin

2013-01-01

Fine particles in hospitality venues with insufficient smoking bans indicate health risks from passive smoking. In a random sample of Viennese inns (restaurants, cafes, bars, pubs and discotheques) effects of partial smoking bans on indoor air quality were examined by measurement of count, size and chargeable surface of ultrafine particles (UFPs) sized 10-300 nm, simultaneously with mass of particles sized 300-2500 nm (PM2.5). Air samples were taken in 134 rooms unannounced during busy hours and analyzed by a diffusion size classifier and an optical particle counter. Highest number concentrations of particles were found in smoking venues and smoking rooms (median 66,011 pt/cm(3)). Even non-smoking rooms adjacent to smoking rooms were highly contaminated (median 25,973 pt/cm(3)), compared with non-smoking venues (median 7408 pt/cm(3)). The particle number concentration was significantly correlated with the fine particle mass (P<0.001). We conclude that the existing tobacco law in Austria is ineffective to protect customers in non-smoking rooms of hospitality premises. Health protection of non-smoking guests and employees from risky UFP concentration is insufficient, even in rooms labeled "non-smoking". Partial smoking bans with separation of smoking rooms failed.

Does e-cigarette consumption cause passive vaping?

PubMed

Schripp, T; Markewitz, D; Uhde, E; Salthammer, T

2013-02-01

Electronic cigarette consumption ('vaping') is marketed as an alternative to conventional tobacco smoking. Technically, a mixture of chemicals containing carrier liquids, flavors, and optionally nicotine is vaporized and inhaled. The present study aims at the determination of the release of volatile organic compounds (VOC) and (ultra)fine particles (FP/UFP) from an e-cigarette under near-to-real-use conditions in an 8-m(3) emission test chamber. Furthermore, the inhaled mixture is analyzed in small chambers. An increase in FP/UFP and VOC could be determined after the use of the e-cigarette. Prominent components in the gas-phase are 1,2-propanediol, 1,2,3-propanetriol, diacetin, flavorings, and traces of nicotine. As a consequence, 'passive vaping' must be expected from the consumption of e-cigarettes. Furthermore, the inhaled aerosol undergoes changes in the human lung that is assumed to be attributed to deposition and evaporation. The consumption of e-cigarettes marks a new source for chemical and aerosol exposure in the indoor environment. To evaluate the impact of e-cigarettes on indoor air quality and to estimate the possible effect of passive vaping, information about the chemical characteristics of the released vapor is needed. © 2012 John Wiley & Sons A/S.

Modelling component evaporation and composition change of traffic-induced ultrafine particles during travel from street canyon to urban background.

PubMed

Nikolova, Irina; MacKenzie, A Rob; Cai, Xiaoming; Alam, Mohammed S; Harrison, Roy M

2016-07-18

We developed a model (CiTTy-Street-UFP) of traffic-related particle behaviour in a street canyon and in the nearby downwind urban background that accounts for aerosol dynamics and the variable vapour pressure of component organics. The model simulates the evolution and fate of traffic generated multicomponent ultrafine particles (UFP) composed of a non-volatile core and 17 Semi-Volatile Organic Compounds (SVOC, modelled as n-alkane proxies). A two-stage modelling approach is adopted: (1) a steady state simulation inside the street canyon is achieved, in which there exists a balance between traffic emissions, condensation/evaporation, deposition, coagulation and exchange with the air above roof-level; and (2) a continuing simulation of the above-roof air parcel advected to the nearby urban park during which evaporation is dominant. We evaluate the component evaporation and associated composition changes of multicomponent organic particles in realistic atmospheric conditions and compare our results with observations from London (UK) in a street canyon and an urban park. With plausible input conditions and parameter settings, the model can reproduce, with reasonable fidelity, size distributions in central London in 2007. The modelled nucleation-mode peak diameter, which is 23 nm in the steady-state street canyon, decreases to 9 nm in a travel time of just 120 s. All modelled SVOC in the sub-10 nm particle size range have evaporated leaving behind only non-volatile material, whereas modelled particle composition in the Aitken mode contains SVOC between C26H54 and C32H66. No data on particle composition are available in the study used for validation, or elsewhere. Measurements addressing in detail the size resolved composition of the traffic emitted UFP in the atmosphere are a high priority for future research. Such data would improve the representation of these particles in dispersion models and provide the data essential for model validation. Enhanced knowledge of the chemical composition of nucleation-mode particles from diesel engine exhaust is needed to predict both their atmospheric behaviour and their implications for human health.

Heterogeneity of passenger exposure to air pollutants in public transport microenvironments

NASA Astrophysics Data System (ADS)

Yang, Fenhuan; Kaul, Daya; Wong, Ka Chun; Westerdahl, Dane; Sun, Li; Ho, Kin-fai; Tian, Linwei; Brimblecombe, Peter; Ning, Zhi

2015-05-01

Epidemiologic studies have linked human exposure to pollutants with adverse health effects. Passenger exposure in public transport systems contributes an important fraction of daily burden of air pollutants. While there is extensive literature reporting the concentrations of pollutants in public transport systems in different cities, there are few studies systematically addressing the heterogeneity of passenger exposure in different transit microenvironments, in cabins of different transit vehicles and in areas with different characteristics. The present study investigated PM2.5 (particulate matter with aerodynamic diameters smaller than 2.5 μm), black carbon (BC), ultrafine particles (UFP) and carbon monoxide (CO) pollutant concentrations in various public road transport systems in highly urbanized city of Hong Kong. Using a trolley case housing numerous portable air monitors, we conducted a total of 119 trips during the campaign. Transit microenvironments, classified as 1). busy and secondary roadside bus stops; 2). open and enclosed termini; 3). above- and under-ground Motor Rail Transport (MTR) platforms, were investigated and compared to identify the factors that may affect passenger exposures. The pollutants inside bus and MTR cabins were also investigated together with a comparison of time integrated exposure between the transit modes. Busy roadside and enclosed termini demonstrated the highest average particle concentrations while the lowest was found on the MTR platforms. Traffic-related pollutants BC, UFP and CO showed larger variations than PM2.5 across different microenvironments and areas confirming their heterogeneity in urban environments. In-cabin pollutant concentrations showed distinct patterns with BC and UFP high in diesel bus cabins and CO high in LPG bus cabins, suggesting possible self-pollution issues and/or penetration of on-road pollutants inside cabins during bus transit. The total passenger exposure along selected routes, showed bus trips had the potential for higher integrated passenger exposure compared to MTR trips. The present study may provide useful information to better characterize the distribution of passenger exposure pattern in health assessment studies and the results also highlight the need to formulate exposure reduction based air policies in large cities.

Highway proximity associated with cardiovascular disease risk: the influence of individual-level confounders and exposure misclassification

PubMed Central

2013-01-01

Background Elevated cardiovascular disease risk has been reported with proximity to highways or busy roadways, but proximity measures can be challenging to interpret given potential confounders and exposure error. Methods We conducted a cross sectional analysis of plasma levels of C-Reactive Protein (hsCRP), Interleukin-6 (IL-6), Tumor Necrosis Factor alpha receptor II (TNF-RII) and fibrinogen with distance of residence to a highway in and around Boston, Massachusetts. Distance was assigned using ortho-photo corrected parcel matching, as well as less precise approaches such as simple parcel matching and geocoding addresses to street networks. We used a combined random and convenience sample of 260 adults >40 years old. We screened a large number of individual-level variables including some infrequently collected for assessment of highway proximity, and included a subset in our final regression models. We monitored ultrafine particle (UFP) levels in the study areas to help interpret proximity measures. Results Using the orthophoto corrected geocoding, in a fully adjusted model, hsCRP and IL-6 differed by distance category relative to urban background: 43% (-16%,141%) and 49% (6%,110%) increase for 0-50 m; 7% (-39%,45%) and 41% (6%,86%) for 50-150 m; 54% (-2%,142%) and 18% (-11%,57%) for 150-250 m, and 49% (-4%, 131%) and 42% (6%, 89%) for 250-450 m. There was little evidence for association for TNF-RII or fibrinogen. Ortho-photo corrected geocoding resulted in stronger associations than traditional methods which introduced differential misclassification. Restricted analysis found the effect of proximity on biomarkers was mostly downwind from the highway or upwind where there was considerable local street traffic, consistent with patterns of monitored UFP levels. Conclusion We found associations between highway proximity and both hsCRP and IL-6, with non-monotonic patterns explained partly by individual-level factors and differences between proximity and UFP concentrations. Our analyses emphasize the importance of controlling for the risk of differential exposure misclassification from geocoding error. PMID:24090339

Highway proximity associated with cardiovascular disease risk: the influence of individual-level confounders and exposure misclassification.

PubMed

Brugge, Doug; Lane, Kevin; Padró-Martínez, Luz T; Stewart, Andrea; Hoesterey, Kyle; Weiss, David; Wang, Ding Ding; Levy, Jonathan I; Patton, Allison P; Zamore, Wig; Mwamburi, Mkaya

2013-10-03

Elevated cardiovascular disease risk has been reported with proximity to highways or busy roadways, but proximity measures can be challenging to interpret given potential confounders and exposure error. We conducted a cross sectional analysis of plasma levels of C-Reactive Protein (hsCRP), Interleukin-6 (IL-6), Tumor Necrosis Factor alpha receptor II (TNF-RII) and fibrinogen with distance of residence to a highway in and around Boston, Massachusetts. Distance was assigned using ortho-photo corrected parcel matching, as well as less precise approaches such as simple parcel matching and geocoding addresses to street networks. We used a combined random and convenience sample of 260 adults >40 years old. We screened a large number of individual-level variables including some infrequently collected for assessment of highway proximity, and included a subset in our final regression models. We monitored ultrafine particle (UFP) levels in the study areas to help interpret proximity measures. Using the orthophoto corrected geocoding, in a fully adjusted model, hsCRP and IL-6 differed by distance category relative to urban background: 43% (-16%,141%) and 49% (6%,110%) increase for 0-50 m; 7% (-39%,45%) and 41% (6%,86%) for 50-150 m; 54% (-2%,142%) and 18% (-11%,57%) for 150-250 m, and 49% (-4%, 131%) and 42% (6%, 89%) for 250-450 m. There was little evidence for association for TNF-RII or fibrinogen. Ortho-photo corrected geocoding resulted in stronger associations than traditional methods which introduced differential misclassification. Restricted analysis found the effect of proximity on biomarkers was mostly downwind from the highway or upwind where there was considerable local street traffic, consistent with patterns of monitored UFP levels. We found associations between highway proximity and both hsCRP and IL-6, with non-monotonic patterns explained partly by individual-level factors and differences between proximity and UFP concentrations. Our analyses emphasize the importance of controlling for the risk of differential exposure misclassification from geocoding error.

Ontology patterns for tabular representations of biomedical knowledge on neglected tropical diseases

PubMed Central

Santana, Filipe; Schober, Daniel; Medeiros, Zulma; Freitas, Fred; Schulz, Stefan

2011-01-01

Motivation: Ontology-like domain knowledge is frequently published in a tabular format embedded in scientific publications. We explore the re-use of such tabular content in the process of building NTDO, an ontology of neglected tropical diseases (NTDs), where the representation of the interdependencies between hosts, pathogens and vectors plays a crucial role. Results: As a proof of concept we analyzed a tabular compilation of knowledge about pathogens, vectors and geographic locations involved in the transmission of NTDs. After a thorough ontological analysis of the domain of interest, we formulated a comprehensive design pattern, rooted in the biomedical domain upper level ontology BioTop. This pattern was implemented in a VBA script which takes cell contents of an Excel spreadsheet and transforms them into OWL-DL. After minor manual post-processing, the correctness and completeness of the ontology was tested using pre-formulated competence questions as description logics (DL) queries. The expected results could be reproduced by the ontology. The proposed approach is recommended for optimizing the acquisition of ontological domain knowledge from tabular representations. Availability and implementation: Domain examples, source code and ontology are freely available on the web at http://www.cin.ufpe.br/~ntdo. Contact: fss3@cin.ufpe.br PMID:21685092

Physico-Chemical Characterization of Fine and Ultrafine Particles Emitted during Diesel Particulate Filter Active Regeneration of Euro5 Diesel Vehicles.

PubMed

R'Mili, Badr; Boréave, Antoinette; Meme, Aurelie; Vernoux, Philippe; Leblanc, Mickael; Noël, Ludovic; Raux, Stephane; D'Anna, Barbara

2018-03-06

Diesel particulate filters (DPFs) are commonly employed in modern passenger cars to comply with current particulate matter (PM) emission standards. DPFs requires periodic regeneration to remove the accumulated matter. During the process, high-concentration particles, in both nucleation and accumulation modes, are emitted. Here, we report new information on particle morphology and chemical composition of fine (FPs) and ultrafine particles (UFPs) measured downstream of the DPF during active regeneration of two Euro 5 passenger cars. The first vehicle was equipped with a close-coupled diesel oxidation catalyst (DOC) and noncatalyzed DPF combined with fuel borne catalyst and the second one with DOC and a catalyzed-diesel particle filter (CDPF). Differences in PM emission profiles of the two vehicles were related to different after treatment design, regeneration strategies, and vehicle characteristics and mileage. Particles in the nucleation mode consisted of ammonium bisulfate, sulfate and sulfuric acid, suggesting that the catalyst desulfation is the key process in the formation of UFPs. Larger particles and agglomerates, ranging from 90 to 600 nm, consisted of carbonaceous material (soot and soot aggregates) coated by condensable material including organics, ammonium bisulfate and sulfuric acid. Particle emission in the accumulation mode was due to the reduced filtration efficiency (soot cake oxidation) throughout the regeneration process.

Composition of Metallic Elements and Size Distribution of Fine and Ultrafine Particles in a Steelmaking Factory.

PubMed

Marcias, Gabriele; Fostinelli, Jacopo; Catalani, Simona; Uras, Michele; Sanna, Andrea Maurizio; Avataneo, Giuseppe; De Palma, Giuseppe; Fabbri, Daniele; Paganelli, Matteo; Lecca, Luigi Isaia; Buonanno, Giorgio; Campagna, Marcello

2018-06-07

The characteristics of aerosol, in particular particle size and chemical composition, can have an impact on human health. Particle size distribution and chemical composition is a necessary parameter in occupational exposure assessment conducted in order to understand possible health effects. The aim of this study was to characterize workplace airborne particulate matter in a metallurgical setting by synergistically using two different approaches; Methodology: Analysis of inhalable fraction concentrations through traditional sampling equipment and ultrafine particles (UFP) concentrations and size distribution was conducted by an Electric Low-Pressure Impactor (ELPI+™). The determination of metallic elements (ME) in particles was carried out by inductively coupled plasma mass spectrometry; Results: Inhalable fraction and ME concentrations were below the limits set by Italian legislation and the American Conference of Governmental Industrial Hygienists (ACGIH, 2017). The median of UFP was between 4.00 × 10⁴ and 2.92 × 10⁵ particles/cm³. ME concentrations determined in the particles collected by ELPI show differences in size range distribution; Conclusions: The adopted synergistic approach enabled a qualitative and quantitative assessment of the particles in steelmaking factories. The results could lead to a better knowledge of occupational exposure characterization, in turn affording a better understanding of occupational health issues due to metal fumes exposure.

Effects of After-Treatment Control Technologies on Heavy-Duty Diesel Truck Emissions

NASA Astrophysics Data System (ADS)

Preble, C.; Dallmann, T. R.; Kreisberg, N. M.; Hering, S. V.; Harley, R.; Kirchstetter, T.

2015-12-01

Diesel engines are major emitters of nitrogen oxides (NOx) and the black carbon (BC) fraction of particulate matter (PM). Diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have recently become standard on new heavy-duty diesel trucks (HDDT). There is concern that DPFs may increase ultrafine particle (UFP) and total particle number (PN) emissions while reducing PM mass emissions. Also, the deliberate catalytic oxidation of engine-out NO to NO2 in continuously regenerating DPFs may lead to increased tailpipe emission of NO2 and near-roadway concentrations that exceed the 1-hr national ambient air quality standard. Increased NO2 emissions can also promote formation of ozone and secondary PM. We report results from ongoing on-road studies of HDDT emissions at the Port of Oakland and the Caldecott Tunnel in California's San Francisco Bay Area. Emission factors (g pollutant per kg diesel) were linked via recorded license plates to each truck's engine model year and installed emission controls. At both sites, DPF use significantly increased the NO2/NOx emission ratio. DPFs also significantly increased NO2 emissions when installed as retrofits on older trucks with higher baseline NOx emissions. While SCR systems on new trucks effectively reduce total NOx emissions and mitigate these undesirable DPF-related NO2 emissions, they also lead to significant emission of N2O, a potent greenhouse gas. When expressed on a CO2-equivalent basis, the N2O emissions increase offsets the fuel economy gain (i.e., the CO2 emission reduction) associated with SCR use. At the Port, average NOx, BC and PN emission factors from new trucks equipped with DPF and SCR were 69 ± 15%, 92 ± 32% and 66 ± 35% lower, respectively, than modern trucks without these emission controls. In contrast, at the Tunnel, PN emissions from older trucks retrofit with DPFs were ~2 times greater than modern trucks without DPFs. The difference could be related to engine temperature, with highway operation producing greater exhaust temperatures that promote UFP nucleation. These studies indicate that DPF and SCR use can mitigate air quality and climate impacts of diesel truck emissions through reductions in BC and NOx. However, increased emissions of N2O, NO2 and PN may offset some of the benefits.

Nanomaterials Versus Ambient Ultrafine Particles: An Opportunity to Exchange Toxicology Knowledge

PubMed Central

Miller, Mark R.; Clift, Martin J.D.; Elder, Alison; Mills, Nicholas L.; Møller, Peter; Schins, Roel P.F.; Vogel, Ulla; Kreyling, Wolfgang G.; Alstrup Jensen, Keld; Kuhlbusch, Thomas A.J.; Schwarze, Per E.; Hoet, Peter; Pietroiusti, Antonio; De Vizcaya-Ruiz, Andrea; Baeza-Squiban, Armelle; Teixeira, João Paulo; Tran, C. Lang; Cassee, Flemming R.

2017-01-01

Background: A rich body of literature exists that has demonstrated adverse human health effects following exposure to ambient air particulate matter (PM), and there is strong support for an important role of ultrafine (nanosized) particles. At present, relatively few human health or epidemiology data exist for engineered nanomaterials (NMs) despite clear parallels in their physicochemical properties and biological actions in in vitro models. Objectives: NMs are available with a range of physicochemical characteristics, which allows a more systematic toxicological analysis. Therefore, the study of ultrafine particles (UFP, <100 nm in diameter) provides an opportunity to identify plausible health effects for NMs, and the study of NMs provides an opportunity to facilitate the understanding of the mechanism of toxicity of UFP. Methods: A workshop of experts systematically analyzed the available information and identified 19 key lessons that can facilitate knowledge exchange between these discipline areas. Discussion: Key lessons range from the availability of specific techniques and standard protocols for physicochemical characterization and toxicology assessment to understanding and defining dose and the molecular mechanisms of toxicity. This review identifies a number of key areas in which additional research prioritization would facilitate both research fields simultaneously. Conclusion: There is now an opportunity to apply knowledge from NM toxicology and use it to better inform PM health risk research and vice versa. https://doi.org/10.1289/EHP424 PMID:29017987

Ultrafine particles and black carbon personal exposures in asthmatic and non-asthmatic children at school age.

PubMed

Pañella, P; Casas, M; Donaire-Gonzalez, D; Garcia-Esteban, R; Robinson, O; Valentín, A; Gulliver, J; Momas, I; Nieuwenhuijsen, M; Vrijheid, M; Sunyer, J

2017-09-01

Traffic-related air pollution (TRAP) exposure during childhood is associated with asthma; however, the contribution of the different TRAP pollutants in each microenvironment (home, school, transportation, others) in asthmatic and non-asthmatic children is unknown. Daily (24-h) personal black carbon (BC), ultrafine particle (UFP), and alveolar lung-deposited surface area (LDSA) individual exposure measurements were obtained from 100 children (29 past and 21 current asthmatics, 50 non-asthmatics) aged 9±0.7 years from the INMA-Sabadell cohort (Catalonia, Spain). Time spent in each microenvironment was derived by the geolocation provided by the smartphone and a new spatiotemporal map-matching algorithm. Asthmatics and non-asthmatics spent the same amount of time at home (60% and 61%, respectively), at school (20% and 23%), on transportation (8% and 7%), and in other microenvironments (7% and 5%). The highest concentrations of all TRAPs were attributed to transportation. No differences in TRAP concentrations were found overall or by type of microenvironment between asthmatics and non-asthmatics, nor when considering past and current asthmatics, separately. In conclusion, asthmatic and non-asthmatic children had a similar time-activity pattern and similar average exposures to BC, UFP, and LDSA concentrations. This suggests that interventions should be tailored to general population, rather than to subgroups defined by disease. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Nanomaterials Versus Ambient Ultrafine Particles: An Opportunity to Exchange Toxicology Knowledge.

PubMed

Stone, Vicki; Miller, Mark R; Clift, Martin J D; Elder, Alison; Mills, Nicholas L; Møller, Peter; Schins, Roel P F; Vogel, Ulla; Kreyling, Wolfgang G; Alstrup Jensen, Keld; Kuhlbusch, Thomas A J; Schwarze, Per E; Hoet, Peter; Pietroiusti, Antonio; De Vizcaya-Ruiz, Andrea; Baeza-Squiban, Armelle; Teixeira, João Paulo; Tran, C Lang; Cassee, Flemming R

2017-10-10

A rich body of literature exists that has demonstrated adverse human health effects following exposure to ambient air particulate matter (PM), and there is strong support for an important role of ultrafine (nanosized) particles. At present, relatively few human health or epidemiology data exist for engineered nanomaterials (NMs) despite clear parallels in their physicochemical properties and biological actions in in vitro models. NMs are available with a range of physicochemical characteristics, which allows a more systematic toxicological analysis. Therefore, the study of ultrafine particles (UFP, <100 nm in diameter) provides an opportunity to identify plausible health effects for NMs, and the study of NMs provides an opportunity to facilitate the understanding of the mechanism of toxicity of UFP. A workshop of experts systematically analyzed the available information and identified 19 key lessons that can facilitate knowledge exchange between these discipline areas. Key lessons range from the availability of specific techniques and standard protocols for physicochemical characterization and toxicology assessment to understanding and defining dose and the molecular mechanisms of toxicity. This review identifies a number of key areas in which additional research prioritization would facilitate both research fields simultaneously. There is now an opportunity to apply knowledge from NM toxicology and use it to better inform PM health risk research and vice versa. https://doi.org/10.1289/EHP424.

Outdoor infiltration and indoor contribution of UFP and BC, OC, secondary inorganic ions and metals in PM2.5 in schools

NASA Astrophysics Data System (ADS)

Rivas, I.; Viana, M.; Moreno, T.; Bouso, L.; Pandolfi, M.; Alvarez-Pedrerol, M.; Forns, J.; Alastuey, A.; Sunyer, J.; Querol, X.

2015-04-01

Infiltration of outdoor-sourced particles into indoor environments in 39 schools in Barcelona was assessed during school hours. Tracers of road traffic emissions (NO2, Equivalent Black Carbon (EBC), Ultrafine Particles (UFP), Sb), secondary inorganic aerosols (SO42-, NO3-, NH4+) and a number of PM2.5 trace elements showed median indoor/outdoor (I/O) ratios ≤ 1, indicating that outdoor sources importantly contributed to indoor concentrations. Conversely, OC and mineral components had I/O ratios>1. Different infiltration factors were found for traffic and secondary components (0.31-0.75 and 0.50-0.92, cold and warm season respectively), with maxima corresponding to EBC and Cd. Higher concentrations of indoor-generated particles were observed when closed windows hindered dispersion (cold season). Building age was not a major determinant of indoor levels. Neither were the window's material, except for NO2 (with an increase of 8 μg m-3 for wood framed windows) and the mineral components (also dependent on the presence of sand in a distance <20 m) that reach the indoor environment via soil adhering to footwear with their dispersion being more barred by Aluminium/PVC framed windows than the wooden ones. Enlarged indoor concentrations of some trace elements suggest the presence of indoor sources that should be further investigated in order to achieve a healthier school indoor environment.

Ectoparasitic hematophagous dipters: potential reservoirs of dengue virus?

PubMed

Setién, Álvaro Aguilar; Baltazar, Anahí García; Leyva, Ignacio Olave; Rojas, Mónica Salas; Koldenkova, Vadim Pérez; García, Mariem Pérez-Peña; Ceballos, Nidia Aréchiga; Romero, Guillermo Gálvez; Villegas, Edgar Olivier López; Malacara, Juan Bibiano Morales; Marín, Cenia Almazán

2017-01-01

Recently, the presence of antibodies and dengue virus (DV) RNA in neotropical wild mammals, including Desmodus rotundus, was reported. In a previous study, DV was also found in a high percentage (39.6%) of ectoparasitic hematophagous dipters specifics of these hematophagous bats. In order to verify the susceptibility of these ectoparasites to DV, in this work experimental infections with VD2 of organs explants of Strebla wiedemanni and of Melophagus ovinus were performed using C6/36 cells as control. Viral titers (UFP/mL) were determined at 0, 48 and 96 hrs pi. Infected organs were observed by electron microscopy and under the confocal microscopy indirect immunofluorescence (IIF) using specific conjugates against DV. The infected organs of both species of ectoparasites replicated DV at titers similar to those obtained with the C6/36 cell line (≥10 6 UFP/mL). Electron microscopy and IIF showed DV replication in the digestive tract, tracheoles, reproductive organs of males but not in females, and milk glands (MG) of both species. In the fatty bodies of the MG of M. ovinus, zones with a high affinity for the DV were observed. In this work the susceptibility of S. wiedemanni and M. ovinus to DV was demonstrated and consequently the probable role of this ectoparasites as wild reservoirs of DV. Copyright: © 2017 SecretarÍa de Salud.

In-vehicle exposures to particulate air pollution in Canadian metropolitan areas: the urban transportation exposure study.

PubMed

Weichenthal, Scott; Van Ryswyk, Keith; Kulka, Ryan; Sun, Liu; Wallace, Lance; Joseph, Lawrence

2015-01-06

Commuters may be exposed to increased levels of traffic-related air pollution owing to close proximity to traffic-emissions. We collected in-vehicle and roof-top air pollution measurements over 238 commutes in Montreal, Toronto, and Vancouver, Canada between 2010 and 2013. Voice recordings were used to collect real-time information on traffic density and the presence of diesel vehicles and multivariable linear regression models were used to estimate the impact of these factors on in-vehicle pollutant concentrations (and indoor/outdoor ratios) along with parameters for road type, land use, and meteorology. In-vehicle PM2.5 and NO2 concentrations consistently exceeded regional outdoor levels and each unit increase in the rate of encountering diesel vehicles (count/min) was associated with substantial increases (>100%) in in-vehicle concentrations of ultrafine particles (UFPs), black carbon, and PM2.5 as well as strong increases (>15%) in indoor/outdoor ratios. A model based on meteorology and the length of highway roads within a 500 m buffer explained 53% of the variation in in-vehicle UFPs; however, models for PM2.5 (R(2) = 0.24) and black carbon (R(2) = 0.30) did not perform as well. Our findings suggest that vehicle commuters experience increased exposure to air pollutants and that traffic characteristics, land use, road types, and meteorology are important determinants of these exposures.

Breaking new ground in mapping human settlements from space - The Global Urban Footprint

NASA Astrophysics Data System (ADS)

Esch, Thomas; Heldens, Wieke; Hirner, Andreas; Keil, Manfred; Marconcini, Mattia; Roth, Achim; Zeidler, Julian; Dech, Stefan; Strano, Emanuele

2017-12-01

Today, approximately 7.2 billion people inhabit the Earth and by 2050 this number will have risen to around nine billion, of which about 70% will be living in cities. The population growth and the related global urbanization pose one of the major challenges to a sustainable future. Hence, it is essential to understand drivers, dynamics, and impacts of the human settlements development. A key component in this context is the availability of an up-to-date and spatially consistent map of the location and distribution of human settlements. It is here that the Global Urban Footprint (GUF) raster map can make a valuable contribution. The new global GUF binary settlement mask shows a so far unprecedented spatial resolution of 0.4″ (∼ 12m) that provides - for the first time - a complete picture of the entirety of urban and rural settlements. The GUF has been derived by means of a fully automated processing framework - the Urban Footprint Processor (UFP) - that was used to analyze a global coverage of more than 180,000 TanDEM-X and TerraSAR-X radar images with 3 m ground resolution collected in 2011-2012. The UFP consists of five main technical modules for data management, feature extraction, unsupervised classification, mosaicking and post-editing. Various quality assessment studies to determine the absolute GUF accuracy based on ground truth data on the one hand and the relative accuracies compared to established settlements maps on the other hand, clearly indicate the added value of the new global GUF layer, in particular with respect to the representation of rural settlement patterns. The Kappa coefficient of agreement compared to absolute ground truth data, for instance, shows GUF accuracies which are frequently twice as high as those of established low resolution maps. Generally, the GUF layer achieves an overall absolute accuracy of about 85%, with observed minima around 65% and maxima around 98%. The GUF will be provided open and free for any scientific use in the full resolution and for any non-profit (but also non-scientific) use in a generalized version of 2.8″ (∼ 84m). Therewith, the new GUF layer can be expected to break new ground with respect to the analysis of global urbanization and peri-urbanization patterns, population estimation, vulnerability assessment, or the modeling of diseases and phenomena of global change in general.

Pharmacological Studies of NOP Receptor Agonists as Novel Analgesics

DTIC Science & Technology

2010-05-01

hydroxymethyl-4-piperidyl]-3-ethyl-1, 3-dihydro- 2H- benzimidazol -2-one (J-113397). J Med Chem 42: 5061–5063. Ko MC, Butelman ER, Traynor JR, Woods JH (1998a...ethyl-1,3-dihydro-2H- benzimidazol -2-one) was used to compare their antagonist effects against both morphine (100 nmol)- and UFP-112 (10 nmol)-induced...3S,4S)-1- (Cyclooctylmethyl)-3-(hydroxymethyl)-4-piperidinyl]-3-ethyl- 1,3-dihydro-2H- benzimidazol -2-one) (Tocris Bioscience, Ellisville, MO), and

Uniform Federal Policy for Quality Assurance Project Plans: Evaluating, Assessing, and Documenting Environmental Data Collection and Use Programs. Part 1. UFP-QAPP Manual

DTIC Science & Technology

2004-07-01

sampler, project manager, data reviewer, statistician , risk assessor, assessment personnel, and laboratory QC manager. In addition, a complete copy of...sample • Corrective actions to be taken if the QC sample fails these criteria • A description of how the QC data and results are to be documented and...Intergovernmental Data Quality Task Force Uniform Federal Policy for Quality Assurance Project Plans Evaluating, Assessing, and Documenting

Ultrafine particles generated from coloring with scented markers in the presence of ozone.

PubMed

Fung, C-C D; Shu, S; Zhu, Y

2014-10-01

High concentrations of ultrafine particles (UFPs) have been previously reported during school art activities. This is possibly due to secondary organic aerosols (SOAs) formed from reactions between ozone and volatile organic compounds emitted from art products. Four brands of markers, three scented and one unscented, were tested inside a stainless steel chamber at eight different ozone concentrations between 0 and 300 ppb. Out of the 32 tested markers, only the lemon- and orange-scented markers from one brand reacted with ozone to form UFPs. Limonene, pinene, and several other terpenes were identified as ingredients of ink in SOA-forming markers. Coloring with one lemon-scented marker for 1 min without ozone generated on average approximately 26 ± 4 ppb of limonene inside the chamber. At 150 ppb ozone, using one lemon marker for 1 min formed on average 7.7 × 10(10) particles. The particle size distribution indicated an initial mode of 15 nm which grew to 40 nm. At 50 ppb ozone and below, no significant SOA formation occurred. The number of particles formed is moderately correlated with the mass of ink used (R(2)  = 0.68). Based on these data, scented markers are not likely a strong source of SOA under normal indoor ozone levels. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Modeling Population Exposure to Ultrafine Particles in a Major Italian Urban Area

PubMed Central

Spinazzè, Andrea; Cattaneo, Andrea; Peruzzo, Carlo; Cavallo, Domenico M.

2014-01-01

Average daily ultrafine particles (UFP) exposure of adult Milan subpopulations (defined on the basis of gender, and then for age, employment or educational status), in different exposure scenarios (typical working day in summer and winter) were simulated using a microenvironmental stochastic simulation model. The basic concept of this kind of model is that time-weighted average exposure is defined as the sum of partial microenvironmental exposures, which are determined by the product of UFP concentration and time spent in each microenvironment. In this work, environmental concentrations were derived from previous experimental studies that were based on microenvironmental measurements in the city of Milan by means of personal or individual monitoring, while time-activity patterns were derived from the EXPOLIS study. A significant difference was observed between the exposures experienced in winter (W: 28,415 pt/cm3) and summer (S: 19,558 pt/cm3). Furthermore, simulations showed a moderate difference between the total exposures experienced by women (S: 19,363 pt/cm3; W: 27,623 pt/cm3) and men (S: 18,806 pt/cm3; W: 27,897 pt/cm3). In addition, differences were found as a function of (I) age, (II) employment status and (III) educational level; accordingly, the highest total exposures resulted for (I) 55–59 years old people, (II) housewives and students and (III) people with higher educational level (more than 10 years of scholarity). Finally, significant differences were found between microenvironment-specific exposures. PMID:25321878

Fine and ultrafine particle doses in the respiratory tract from digital printing operations.

PubMed

Voliotis, Aristeidis; Karali, Irene; Kouras, Athanasios; Samara, Constantini

2017-01-01

In this study, we report for the first time particle number doses in different parts of the human respiratory tract and real-time deposition rates for particles in the 10 nm to 10 μm size range emitted by digital printing operations. Particle number concentrations (PNCs) and size distribution were measured in a typical small-sized printing house using a NanoScan scanning mobility particle sizer and an optical particle sizer. Particle doses in human lung were estimated applying a multiple-path particle dosimetry model under two different breathing scenarios. PNC was dominated by the ultrafine particle fractions (UFPs, i.e., particles smaller than 100 nm) exhibiting almost nine times higher levels in comparison to the background values. The average deposition rate fοr each scenario in the whole lung was estimated at 2.0 and 2.9 × 10 7 particles min -1 , while the respective highest particle dose in the tracheobronchial tree (2.0 and 2.9 × 10 9 particles) was found for diameter of 50 nm. The majority of particles appeared to deposit in the acinar region and most of them were in the UFP size range. For both scenarios, the maximum deposition density (9.5 × 10 7 and 1.5 × 10 8 particles cm -2 ) was observed at the lobar bronchi. Overall, the differences in the estimated particle doses between the two scenarios were 30-40% for both size ranges.

Ultrafine carbon particles promote rotenone-induced dopamine neuronal loss through activating microglial NADPH oxidase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yinxi; Liu, Dan; Zhang, Huifeng

Background: Atmospheric ultrafine particles (UFPs) and pesticide rotenone were considered as potential environmental risk factors for Parkinson's disease (PD). However, whether and how UFPs alone and in combination with rotenone affect the pathogenesis of PD remains largely unknown. Methods: Ultrafine carbon black (ufCB, a surrogate of UFPs) and rotenone were used individually or in combination to determine their roles in chronic dopaminergic (DA) loss in neuron-glia, and neuron-enriched, mix-glia cultures. Immunochemistry using antibody against tyrosine hydroxylase was performed to detect DA neuronal loss. Measurement of extracellular superoxide and intracellular reactive oxygen species (ROS) were performed to examine activation of NADPHmore » oxidase. Genetic deletion and pharmacological inhibition of NADPH oxidase and MAC-1 receptor in microglia were employed to examine their role in DA neuronal loss triggered by ufCB and rotenone. Results: In rodent midbrain neuron-glia cultures, ufCB and rotenone alone caused neuronal death in a dose-dependent manner. In particularly, ufCB at doses of 50 and 100 μg/cm{sup 2} induced significant loss of DA neurons. More importantly, nontoxic doses of ufCB (10 μg/cm{sup 2}) and rotenone (2 nM) induced synergistic toxicity to DA neurons. Microglial activation was essential in this process. Furthermore, superoxide production from microglial NADPH oxidase was critical in ufCB/rotenone-induced neurotoxicity. Studies in mix-glia cultures showed that ufCB treatment activated microglial NADPH oxidase to induce superoxide production. Firstly, ufCB enhanced the expression of NADPH oxidase subunits (gp91{sup phox}, p47{sup phox} and p40{sup phox}); secondly, ufCB was recognized by microglial surface MAC-1 receptor and consequently promoted rotenone-induced p47{sup phox} and p67{sup phox} translocation assembling active NADPH oxidase. Conclusion: ufCB and rotenone worked in synergy to activate NADPH oxidase in microglia, leading to oxidative damage to DA neurons. Our findings delineated the potential role of ultrafine particles alone and in combination with pesticide rotenone in the pathogenesis of PD. - Graphical abstract: Ultrafine particles and rotenone synergistically induce the assembly of active form NADPH oxidase complex in microglia inducing oxidative damage to dopamine neurons. - Highlights: • Ultrafine carbon black promotes dopaminergic neuronal loss induced by rotenone. • The role and underlying mechanism of ultrafine particles in the pathogenesis of PD • NADPH oxidase is a potential therapeutic target of Parkinson's disease.« less

Instrument comparison for Aerosolized Titanium Dioxide

NASA Astrophysics Data System (ADS)

Ranpara, Anand

Recent toxicological studies have shown that the surface area of ultrafine particles (UFP i.e., particles with diameters less than 0.1 micrometer) has a stronger correlation with adverse health effects than does mass of these particles. Ultrafine titanium dioxide (TiO2) particles are widely used in industry, and their use is associated with adverse health outcomes, such as micro vascular dysfunctions and pulmonary damages. The primary aim of this experimental study was to compare a variety of laboratory and industrial hygiene (IH) field study instruments all measuring the same aerosolized TiO2. The study also observed intra-instrument variability between measurements made by two apparently identical devices of the same type of instrument placed side-by-side. The types of instruments studied were (1) DustTrak(TM) DRX, (2) Personal Data RAMs(TM) (PDR), (3) GRIMM, (4) Diffusion charger (DC) and (5) Scanning Mobility Particle Sizer (SMPS). Two devices of each of the four IH field study instrument types were used to measure six levels of mass concentration of fine and ultrafine TiO2 aerosols in controlled chamber tests. Metrics evaluated included real-time mass, active surface area and number/geometric surface area distributions, and off-line gravimetric mass and morphology on filters. DustTrak(TM) DRXs and PDRs were used for mass concentration measurements. DCs were used for active surface area concentration measurements. GRIMMs were used for number concentration measurements. SMPS was used for inter-instrument comparisons of surface area and number concentrations. The results indicated that two apparently identical devices of each DRX and PDR were statistically not different with each other for all the trials of both the sizes of powder (p < 5%). Mean difference between mass concentrations measured by two DustTrak DRX devices was smaller than that measured by two PDR devices. DustTrak DRX measurements were closer to the reference method, gravimetric mass concentration, than the PDRs. Two apparently identical DC devices were statistically different with each other for fine particles but not for UFP. DC devices and SMPS were statistically different with each other for both sizes of particles. Two apparently identical GRIMM devices were statistically different with each other for fine particles. For UFP, results of GRIMM device were statistically different than SMPS but not for fine particles. These observations suggest that inter-device within instrument and inter-instrument agreements depend on particle size and instrument characteristics to measure nanoparticles at different concentration levels.

Proceedings of US-Latin American Workshop on Molecular and Materials Sciences: Theoretical and Computational Aspects Held in Gainesville, Florida on 10-12 March 1993

DTIC Science & Technology

1994-08-09

City Josd Rdamier and R. Iterative Bogoliubov Transformations and Applications Jauregui Inst. de Fisica , Cuernavaca, Meiico Peter J. Reynolds Quantum...University, Provo, UT 84602 J. R•camier Instituto de Fisica , UNAM, Cuernavaca, Mor., MWxico Gamow states are solutions to the Schr6dinger equation with a...Coutinho Departamento de FAsica do UFPE 50732-910 Recife, PE, Brazil and Jnstituto de Fisica da USP, Czp 20516 01498-970 Sdo Paulo, SP, Brasil The

Association of Long-Term Near-Highway Exposure to Ultrafine Particles with Cardiovascular Diseases, Diabetes and Hypertension.

PubMed

Li, Yu; Lane, Kevin J; Corlin, Laura; Patton, Allison P; Durant, John L; Thanikachalam, Mohan; Woodin, Mark; Wang, Molin; Brugge, Doug

2017-04-26

Ultrafine particle (UFP) concentrations are elevated near busy roadways, however, their effects on prevalence of cardiovascular diseases, diabetes, and hypertension are not well understood. To investigate these associations, data on demographics, diseases, medication use, and time of activities were collected by in-home surveys for 704 participants in three pairs of near-highway and urban background neighborhoods in and near Boston (MA, USA). Body mass index (BMI) was measured for a subset of 435 participants. Particle number concentration (PNC, a measure of UFP) was collected by mobile monitoring in each area. Intra-neighborhood spatial-temporal regression models (approximately 20 m resolution) were used to estimate hourly ambient PNC at the residences of participants. We used participant time activity information to adjust annual average residential PNC values and assign individualized time activity adjusted annual average PNC exposures (TAA-PNC). Using multivariate logistic regression models, we found an odds ratio (OR) of 1.35 (95% CI: 0.83, 2.22) of TAA-PNC with stroke and ischemic heart diseases (S/IHD), an OR of 1.14 (95% CI: 0.81, 1.62) with hypertension, and an OR of 0.71 (95% CI: 0.46, 1.10) for diabetes. A subset analysis controlling for BMI produced slightly stronger associations for S/IHD (OR = 1.61, 95% CI: 0.88, 2.92) and hypertension (OR = 1.28, 95% CI: 0.81, 2.02), and no association with diabetes (OR = 1.09, 95% CI = 0.61, 1.96). Further research is needed with larger sample sizes and longitudinal follow-up.

A study of ambient fine particles at Tianjin International Airport, China.

PubMed

Ren, Jianlin; Liu, Junjie; Li, Fei; Cao, Xiaodong; Ren, Shengxiong; Xu, Bin; Zhu, Yifang

2016-06-15

The total count number concentration of particles from 10 to 1000nm, particle size distribution, and PM2.5 (aerodynamic diameter≤2.5μm) mass concentration were measured on a parking apron next to the runway at Tianjin International Airport in China. The data were collected 250, 270, 300, 350, and 400m from the runway. Wind direction and wind speed played important roles in determining the characteristics of the atmospheric particles. An inverted U-shaped relationship was observed between the measured particle number concentration and wind speed, with an average peak concentration of 2.2×10(5)particles/cm(3) at wind speeds of approximately 4-5m/s. The atmospheric particle number concentration was affected mainly by aircraft takeoffs and landings, and the PM2.5 mass concentration was affected mainly by the relative humidity (RH) of the atmosphere. Ultrafine particles (UFPs, diameter<100nm), with the highest number concentration at a particle size of approximately 16nm, dominated the measured particle size distributions. The calculated particle emission index values for aircraft takeoff and landing were nearly the same, with mean values of 7.5×10(15)particles/(kg fuel) and 7.6×10(15)particles/(kg fuel), respectively. The particle emission rate for one aircraft during takeoff is two orders of magnitude higher than for all gasoline-powered passenger vehicles in Tianjin combined. The particle number concentrations remained much higher than the background concentrations even beyond 400m from the runway. Copyright © 2016 Elsevier B.V. All rights reserved.

Secondary organic aerosol formation from ozone-initiated reactions with nicotine and secondhand tobacco smoke

NASA Astrophysics Data System (ADS)

Sleiman, Mohamad; Destaillats, Hugo; Smith, Jared D.; Liu, Chen-Lin; Ahmed, Musahid; Wilson, Kevin R.; Gundel, Lara A.

2010-11-01

We used controlled laboratory experiments to evaluate the aerosol-forming potential of ozone reactions with nicotine and secondhand smoke. Special attention was devoted to real-time monitoring of the particle size distribution and chemical composition of SOA as they are believed to be key factors determining the toxicity of SOA. The experimental approach was based on using a vacuum ultraviolet photon ionization time-of-flight aerosol mass spectrometer (VUV-AMS), a scanning mobility particle sizer (SMPS) and off-line thermal desorption coupled to mass spectrometry (TD-GC-MS) for gas-phase byproducts analysis. Results showed that exposure of SHS to ozone induced the formation of ultrafine particles (<100 nm) that contained high molecular weight nitrogenated species ( m/ z 400-500), which can be due to accretion/acid-base reactions and formation of oligomers. In addition, nicotine was found to contribute significantly (with yields 4-9%) to the formation of secondary organic aerosol through reaction with ozone. The main constituents of the resulting SOA were tentatively identified and a reaction mechanism was proposed to elucidate their formation. These findings identify a new component of thirdhand smoke that is associated with the formation of ultrafine particles (UFP) through oxidative aging of secondhand smoke. The significance of this chemistry for indoor exposure and health effects is highlighted.

Interaction of ozone with wooden building products, treated wood samples and exotic wood species

NASA Astrophysics Data System (ADS)

Schripp, Tobias; Langer, Sarka; Salthammer, Tunga

2012-07-01

Wooden building products indoors are known to be able to affect the perceived air quality depending on their emission strength. The indoor application of modern ecological lacquer systems (eco-lacquers or 'green' lacquers) may be a much stronger source than the substrates itself. Especially with regard to the formation of ultrafine particles by gas-to-particle conversion in the presence of ozone or other reactive species the impact of the applied building products on the indoor air quality has to be addressed. The present study reports a two concentration step ozonation of OSB panels, painted beech boards, and a number of solid 'exotic' wood types in a 1 m³ emission test chamber. The emission of volatile organic compounds (VOC) was recorded as well as the formation of ultrafine particles in the range 7-300 nm. The products are characterized on the basis of their ozone deposition velocity; the obtained values of 0.008-0.381 cm s-1 are comparable with previously published data. Within the samples of the present study one eco-lacquer was the strongest source of VOC (total VOC ˜ 60 mg m-3) while the wooden building products (OSB) were of intermediate emission strength. The lowest emission was found for the solid (exotic) wood samples. The VOC release of the samples corresponded roughly to the particle formation potential. However, the strongest UFP formation was measured for one solid wood sample ('Garapa') which showed a strong surface reaction in the presence of ozone and formed a large number of particles <40 nm. Overall, the experiments demonstrated the necessity of real-life samples for the estimation of UFP indoor air pollution from the ozone chemistry of terpenes.

Traffic emission factors of ultrafine particles: effects from ambient air.

PubMed

Janhäll, Sara; Molnar, Peter; Hallquist, Mattias

2012-09-01

Ultrafine particles have a significant detrimental effect on both human health and climate. In order to abate this problem, it is necessary to identify the sources of ultrafine particles. A parameterisation method is presented for estimating the levels of traffic-emitted ultrafine particles in terms of variables describing the ambient conditions. The method is versatile and could easily be applied to similar datasets in other environments. The data used were collected during a four-week period in February 2005, in Gothenburg, as part of the Göte-2005 campaign. The specific variables tested were temperature (T), relative humidity (RH), carbon monoxide concentration (CO), and the concentration of particles up to 10 μm diameter (PM(10)); all indicators are of importance for aerosol processes such as coagulation and gas-particle partitioning. These variables were selected because of their direct effect on aerosol processes (T and RH) or as proxies for aerosol surface area (CO and PM(10)) and because of their availability in local monitoring programmes, increasing the usability of the parameterization. Emission factors are presented for 10-100 nm particles (ultrafine particles; EF(ufp)), for 10-40 nm particles (EF(10-40)), and for 40-100 nm particles (EF(40-100)). For EF(40-100) no effect of ambient conditions was found. The emission factor equations are calculated based on an emission factor for NO(x) of 1 g km(-1), thus the particle emission factors are easily expressed in units of particles per gram of NO(x) emitted. For 10-100 nm particles the emission factor is EF(ufp) = 1.8 × 10(15) × (1 - 0.095 × CO - 3.2 × 10(-3) × T) particles km(-1). Alternative equations for the EFs in terms of T and PM(10) concentration are also presented.

Particle exposure and inhaled dose during commuting in Singapore

NASA Astrophysics Data System (ADS)

Tan, Sok Huang; Roth, Matthias; Velasco, Erik

2017-12-01

Exposure concentration and inhaled dose of particles during door-to-door trips walking and using motorized transport modes (subway, bus, taxi) are evaluated along a selected route in a commercial district of Singapore. Concentrations of particles smaller than 2.5 μm in size (PM2.5), black carbon, particle-bound polycyclic aromatic hydrocarbons, number of particles, active surface area and carbon monoxide have been measured in-situ using portable instruments. Simultaneous measurements were conducted at a nearby park to capture the background concentrations. The heart rate of the participants was monitored during the measurements as a proxy of the inhalation rate used to calculate the inhaled dose of particles. All measured metrics were highest and well above background levels during walking. No significant difference was observed in the exposure concentration of PM2.5 for the three motorized transport modes, unlike for the metrics associated with ultrafine particles (UFP). The concentration of these freshly emitted particles was significantly lower on subway trips. The absence of combustion sources, use of air conditioning and screen doors at station platforms are effective measures to protect passengers' health. For other transport modes, sections of trips close to accelerating and idling vehicles, such as bus stops, traffic junctions and taxi stands, represent hotspots of particles. Reducing the waiting time at such locations will lower pollutants exposure and inhaled dose during a commute. After taking into account the effect of inhalation and travel duration when calculating dose, the health benefit of commuting by subway for this particular district of Singapore became even more evident. For example, pedestrians breathe in 2.6 and 3.2 times more PM2.5 and UFP, respectively than subway commuters. Public buses were the second best alternative. Walking emerged as the worst commuting mode in terms of particle exposure and inhaled dose.

Ligand- and cell-dependent determinants of internalization and cAMP modulation by delta opioid receptor (DOR) agonists

PubMed Central

Charfi, Iness; Nagi, Karim; Mnie-Filali, Ouissame; Thibault, Dominic; Balboni, Gianfranco; Schiller, Peter W.; Trudeau, Louis-Eric

2014-01-01

Signaling bias refers to G protein-coupled receptor ligand ability to preferentially activate one type of signal over another. Bias to evoke signaling as opposed to sequestration has been proposed as a predictor of opioid ligand potential for generating tolerance. Here we measured whether delta opioid receptor agonists preferentially inhibited cyclase activity over internalization in HEK cells. Efficacy (τ) and affinity (KA) values were estimated from functional data and bias was calculated from efficiency coefficients (log τ/KA). This approach better represented the data as compared to alternative methods that estimate bias exclusively from τ values. Log (τ/KA) coefficients indicated that SNC-80 and UFP-512 promoted cyclase inhibition more efficiently than DOR internalization as compared to DPDPE (bias factor for SNC-80: 50 and for UFP-512: 132). Molecular determinants of internalization were different in HEK293 cells and neurons with βarrs contributing to internalization in both cell types, while PKC and GRK2 activities were only involved in neurons. Rank orders of ligand ability to engage different internalization mechanisms in neurons were compared to rank order of Emax values for cyclase assays in HEK cells. Comparison revealed a significant reversal in rank order for cyclase Emax values and βarr-dependent internalization in neurons, indicating that these responses were ligand-specific. Despite this evidence, and because kinases involved in internalization were not the same across cellular backgrounds, it is not possible to assert if the magnitude and nature of bias revealed by rank orders of maximal responses is the same as the one measured in HEK cells. PMID:24022593

Impact of smoking on in-vehicle fine particle exposure during driving

NASA Astrophysics Data System (ADS)

Sohn, Hongji; Lee, Kiyoung

2010-09-01

Indoor smoking ban in public places can reduce secondhand smoke (SHS) exposure. However, smoking in cars and homes has continued. The purpose of this study was to assess particulate matter less than 2.5 μm (PM 2.5) concentration in moving cars with different window opening conditions. The PM 2.5 level was measured by an aerosol spectrometer inside and outside moving cars simultaneously, along with ultrafine particle (UFP) number concentration, speed, temperature and humidity inside cars. Two sport utility vehicles were used. Three different ventilation conditions were evaluated by up to 20 repeated experiments. In the pre-smoking phase, average in-vehicle PM 2.5 concentrations were 16-17 μg m -3. Regardless of different window opening conditions, the PM 2.5 levels promptly increased when smoking occurred and decreased after cigarette was extinguished. Although only a single cigarette was smoked, the average PM 2.5 levels were 506-1307 μg m -3 with different window opening conditions. When smoking was ceased, the average PM 2.5 levels for 15 min were several times higher than the US National Ambient Air Quality Standard of 35 μg m -3. It took longer than 10 min to reach the level of the pre-smoking phase. Although UFP levels had a similar temporal profile of PM 2.5, the increased levels during the smoking phase were relatively small. This study demonstrated that the SHS exposure in cars with just a single cigarette being smoked could exceed the US EPA NAAQS under realistic window opening conditions. Therefore, the findings support the need for public education against smoking in cars and advocacy for a smoke-free car policy.

Applications of UAVs to Measurement and Monitoring of Anthropogenic Contamination of an Urban Wildlife Preserve

NASA Astrophysics Data System (ADS)

Higa, E.; Valencia, D.; Hunt, A.

2017-12-01

Over the past decade, the use of unmanned aerial vehicles (UAV's) has seen unprecedented growth in diverse research areas due to advances in UAV hardware and reduced total operating costs. These developments have given environmental investigators a new aerial data acquisition technique that can be used to not only survey large areas of terrain in a time-efficient and cost-effective manner but can be used to gather previously almost unattainable air quality data. Vertically resolved profiles of air pollutant data can be readily constructed. This project's goal is to produce a time resolved (seasonal) aerial survey of a 150-acre section from a 1300-acre ecologically diverse park of bottomland forests, wetlands and prairies. This ecosystem provides abundant habitats for a diverse wildlife community. This section was chosen due to its close proximity to the city landfill located 0.5 miles due north from the chosen section. The process of collecting UAV aerial images at a constant altitude of ( 200ft) on a bi-monthly basis (for a period of 6 months) has commenced. The UAV has been fitted with a custom made mount to secure an Ultrafine Particle (UFP) counter; this is providing information on UFP levels over the study area as a proxy for airborne particle inputs to the site. Sediment samples will be taken from several runoff ponds within the survey area to evaluate possible anthropogenic contamination of the park . Post processing imaging software, DroneDeploy, is being used to create an orthomosaic, topographic surface and 3D model that can be integrated with GIS platforms to create a comprehensive and cohesive multi-layered data set. Data sets of this nature will provide information on temporally constrained sources of runoff material to the pond areas in the preserve.

Pilot study of high-performance air filtration for classroom applications.

PubMed

Polidori, A; Fine, P M; White, V; Kwon, P S

2013-06-01

A study was conducted to investigate the effectiveness of three air purification systems in reducing the exposure of children to air contaminants inside nine classrooms of three Southern California schools. Continuous and integrated measurements were conducted to monitor the indoor and outdoor concentrations of ultrafine particles (UFPs), fine and coarse particulate matter (PM2.5 and PM10 , respectively), black carbon (BC), and volatile organic compounds. An heating, ventilating, and air conditioning (HVAC)-based high-performance panel filter (HP-PF), a register-based air purifier (RS), and a stand-alone air cleaning system (SA) were tested alone and in different combinations for their ability to remove the monitored pollutants. The combination of a RS and a HP-PF was the most effective solution for lowering the indoor concentrations of BC, UFPs, and PM2.5 , with study average reductions between 87% and 96%. When using the HP-PF alone, reductions close to 90% were also achieved. In all cases, air quality conditions were improved substantially with respect to the corresponding baseline (preexisting) conditions. Data on the performance of the gas-absorbing media included in the RS and SA unit were inconclusive, and their effectiveness, lifetime, costs, and benefits must be further assessed before conclusions and recommendations can be made. The installation of effective air filtration devices in classrooms may be an important mitigation measure to help reduce the exposure of school children to indoor pollutants of outdoor origin including ultrafine particles and diesel particulate matter, especially at schools located near highly trafficked freeways, refineries, and other important sources of air toxics. Published 2012. This article is a US Government work and is in the public domain in the USA.

Antidepressant activity of nociceptin/orphanin FQ receptor antagonists in the mouse learned helplessness.

PubMed

Holanda, Victor A D; Medeiros, Iris U; Asth, Laila; Guerrini, Remo; Calo', Girolamo; Gavioli, Elaine C

2016-07-01

Pharmacological and genetic evidence support antidepressant-like effects elicited by the blockade of the NOP receptor. The learned helplessness (LH) model employs uncontrollable and unpredictable electric footshocks as a stressor stimulus to induce a depressive-like phenotype that can be reversed by classical antidepressants. The present study aimed to evaluate the action of NOP receptor antagonists in helpless mice. Male Swiss mice were subjected to the three steps of the LH paradigm (i.e., (1) induction, (2) screening, and (3) test). Only helpless animals were subjected to the test session. During the test session, animals were placed in the electrified chamber and the latency to escape after the footshock and the frequency of escape failures were recorded. The effect of the following treatments administered before the test session were evaluated: nortriptyline (30 mg/kg, ip, 60 min), fluoxetine (30 mg/kg, ip, four consecutive days of treatment), and NOP antagonists SB-612111 (1-10 mg/kg, ip, 30 min) and UFP-101 (1-10 nmol, icv, 5 min). To rule out possible biases, the effects of treatments on controllable stressful and non stressful situations were assessed. In helpless mice, nortriptyline, fluoxetine, UFP-101 (3-10 nmol), and SB-612111 (3-10 mg/kg) significantly reduced escape latencies and escape failures. No effects of drug treatments were observed in mice subjected to the controllable electric footshocks and non stressful situations. Acute treatment with NOP antagonists reversed helplessness similarly to the classical antidepressants. These findings support the proposal that NOP receptor antagonists are worthy of development as innovative antidepressant drugs.

The biological effects upon the cardiovascular system consequent to exposure to particulates of less than 500 nm in size.

PubMed

Clark, James; Gregory, Clive C; Matthews, Ian P; Hoogendoorn, Bastiaan

2016-01-01

Ultrafine particulate matter contribution to cardiovascular disease is not known and not regulated. PM up to 500 nm are abundant in urban air and alveolar deposition is significant. Effects beyond the alveolar barrier within the body or in vitro tissues exposed to particles <500 nm. MEDLINE; Ovid-MEDLINE PREM; Web of Science; PubMed (SciGlobe). 127 articles. Results in tables: "subject type exposed", "exposure type", "technique". Heart rate, vasoactivity, atherosclerotic advancement, oxidative stress, coagulability, inflammatory changes are affected. Production of reactive oxygen species is a useful target to limit outcomes associated with UFP exposure.

PREFACE: 21st Latin American Symposium on Solid State Physics (SLAFES XXI)

NASA Astrophysics Data System (ADS)

Aguiar, J. Albino

2014-04-01

The Latin American Symposium on Solid State Physics (SLAFES) started in Caracas-Venezuela, and over time the symposia have taken place in 9 different Latin American countries. The last five events took place in Mérida-Venezuela (2002), Havana-Cuba (2004), Puebla-Mexico (2006), Puerto Iguazú-Argentina (2008) and Maragogi-Brazil (2011). During the last years, in the different SLAFES editions, the aim has been to bring together researches from Latina America and invite renowned scientists from around the world to a unique forum to discuss the latest developments regarding Solid state Physics. The 21st Latin American Symposium on Solid State Physics (SLAFES XXI) was held in Villa de Leyva-Colombia, from September 30 to October 04, 2013. The 21st SLAFES version featured the participation of experts in various areas of Solid State Physics from countries such as Belgium, Germany, United States, Spain, Ireland, Chile, Argentina and Brazil, had 270 submitted works and was attended by 140 researchers. The development of this event was made possible by financial support from the Universidad Pedagógica y Tecnológica de Colombia, Universidad Nacional de Colombia, Universidad del Norte-CO, Universidad de Magdalena-CO, Universidade Federal de Pernambuco-BR and the Academia Colombiana de Ciencias Exatas, Naturales y Física. Editors Professor J Albino Aguiar Departamento de Física Universidade Federal de Pernambuco 50670-901 Recife PE Brazil e-mail: albino@df.ufpe.br Professor Jairo Roa-Rojas Grupo de Física de Nuevos Materiales Departamento de Física Universidad Nacional de Colombia A.A. 5997 Bogotá DC, Colombia e-mail: jroar@unal.edu.co Professor Carlos Arturo Parra Vargas Grupo Física de Materiales Escuela de Física Universidad Padagógica y Tecnológica de Colombia Tunja Colombia e-mail: carlos.parra@uptc.edu.co Professor David A Land\\'i nez Téllez Grupo de Física de Nuevos Materiales Departamento de Física Universidad Nacional de Colombia A.A. 5997 Bogotá DC Colombia e-mail: dalandinezt@unal.edu.co Professor Laura T Corredor Bohórquez Departamento de Física Universidade Federal de Pernambuco 50670-901 Recife PE Brazil e-mail: ltcorredorb@df.ufpe.br Professor Arkady Shanenko Departamento de Física Universidade Federal de Pernambuco 50670-901 Recife PE Brazil e-mail: arkadyshanenko@df.ufpe.br Professor Renato F Jardim Instituto de Física Universidade de S\\~ao Paulo CP 66318 S\\~ao Paulo SP Brazil e-mail: rjardim@if.usp.br Professor Francois Peeters Department Fysica Universiteit Antwerpen Groneneborgerlann 171 B-2020, Antwerpen Belgium e-mail: francois.peeters@uantwerpen.be Organizing committee ChairmanCarlos Arturo Parra Vargas Proceedings EditorJosé Albino Aguiar Program ChairJairo Roa-Rojas SecretaryAura Janeth Barón González TreasurerArmando Sarmiento Santos Speaker ChairRafael González Hernández Fernando Naranjo Mayorga David A Landínez Téllez Jesús Oswaldo Morán José Sierra Ortega

Somatotype analysis of physically active individuals.

PubMed

Almeida, A H S; Santos, S A G; Castro, P J P; Rizzo, J A; Batista, G R

2013-06-01

The present study aimed at comparing demographic variables, physical activity level, and health-related anthropometric indicators according to somatotype among physically active individuals. This is a descriptive cross-sectional study, in which the sample consisted of 304 individuals, who are users of the jogging track at the Federal University of Pernambuco (UFPE) in Recife, state of Pernambuco, northeastern Brazil. Somatotypes were analyzed using the anthropometric technique proposed by Heath & Carter (1990). To assess physical activity level, we used the short version of the International Physical Activity Questionnaire (IPAQ). We used as health-related anthropometric indicators: body mass index (BMI), waist circumference (WC), waist-hip ratio (WHR), and conicity index (CI). We used descriptive statistics to characterize the sample, and then used a multivariate analysis of variance (a = 0.05) to test for differences. In the somatotype analysis, we observed among women significant predominance of the endomorphy and lower predominance of the ectomorphy in comparison to men. In the age group ≤ 29 years significantly lower values were found for endomorphy than in other age groups. Irregularly active individuals had significantly lower values of endomorphy. We observed that individuals with obesity and risk in WHR, WC and CI had higher scores of endomorphy and mesomorphy and lower scores of ectomorphy. The somatotype of physically active individuals in the present study raises health concern, mainly related to high relative adiposity represented by endomorphy.

Nanoparticle Toxicity Mechanisms: Oxidative Stress and Inflammation

NASA Astrophysics Data System (ADS)

L'Azou, Béatrice; Marano, Francelyne

Toxicology plays a key role in understanding the potentially harmful biological effects of nanoparticles, since epidemiological studies are still difficult to implement given the lack of data concerning exposure. For this reason, in 2005, Günter Oberdörster coined the term `nanotoxicology' to specify the emerging discipline that dealt with ultrafine particles (UFP). It involves in vivo or in vitro studies under controlled conditions to establish the dose-response relationship, so difficult to expose by epidemiological studies. It also aims to determine the thresholds below which biological effects are no longer observed. It is concerned with the role played by properties specific to nanoparticles in the biological response: size, surface reactivity, chemical composition, solubility, etc.

Size resolved ultrafine particles emission model--a continues size distribution approach.

PubMed

Nikolova, Irina; Janssen, Stijn; Vrancken, Karl; Vos, Peter; Mishra, Vinit; Berghmans, Patrick

2011-08-15

A new parameterization for size resolved ultrafine particles (UFP) traffic emissions is proposed based on the results of PARTICULATES project (Samaras et al., 2005). It includes the emission factors from the Emission Inventory Guidebook (2006) (total number of particles, #/km/veh), the shape of the corresponding particle size distribution given in PARTICULATES and data for the traffic activity. The output of the model UFPEM (UltraFine Particle Emission Model) is a sum of continuous distributions of ultrafine particles emissions per vehicle type (passenger cars and heavy duty vehicles), fuel (petrol and diesel) and average speed representative for urban, rural and highway driving. The results from the parameterization are compared with measured total number of ultrafine particles and size distributions in a tunnel in Antwerp (Belgium). The measured UFP concentration over the entire campaign shows a close relation to the traffic activity. The modelled concentration is found to be lower than the measured in the campaign. The average emission factor from the measurement is 4.29E+14 #/km/veh whereas the calculated is around 30% lower. A comparison of emission factors with literature is done as well and in overall a good agreement is found. For the size distributions it is found that the measured distributions consist of three modes--Nucleation, Aitken and accumulation and most of the ultrafine particles belong to the Nucleation and the Aitken modes. The modelled Aitken mode (peak around 0.04-0.05 μm) is found in a good agreement both as amplitude of the peak and the number of particles whereas the modelled Nucleation mode is shifted to smaller diameters and the peak is much lower that the observed. Time scale analysis shows that at 300 m in the tunnel coagulation and deposition are slow and therefore neglected. The UFPEM emission model can be used as a source term in dispersion models. Copyright © 2011 Elsevier B.V. All rights reserved.

Neuropathological Consequences of Gestational Exposure to Concentrated Ambient Fine and Ultrafine Particles in the Mouse.

PubMed

Klocke, Carolyn; Allen, Joshua L; Sobolewski, Marissa; Mayer-Pröschel, Margot; Blum, Jason L; Lauterstein, Dana; Zelikoff, Judith T; Cory-Slechta, Deborah A

2017-04-01

Increasing evidence indicates that the central nervous system (CNS) is a target of air pollution. We previously reported that postnatal exposure of mice to concentrated ambient ultrafine particles (UFP; ≤100 nm) via the University of Rochester HUCAPS system during a critical developmental window of CNS development, equivalent to human 3rd trimester, produced male-predominant neuropathological and behavioral characteristics common to multiple neurodevelopmental disorders, including autism spectrum disorder (ASD), in humans. The current study sought to determine whether vulnerability to fine (≤2.5 μm) and UFP air pollution exposure extends to embryonic periods of brain development in mice, equivalent to human 1st and 2nd trimesters. Pregnant mice were exposed 6 h/day from gestational days (GDs) 0.5-16.5 using the New York University VACES system to concentrated ambient fine/ultrafine particles at an average concentration of 92.69 μg/m3 over the course of the exposure period. At postnatal days (PNDs) 11-15, neuropathological consequences were characterized. Gestational air pollution exposures produced ventriculomegaly, increased corpus callosum (CC) area and reduced hippocampal area in both sexes. Both sexes demonstrated CC hypermyelination and increased microglial activation and reduced total CC microglia number. Analyses of iron deposition as a critical component of myelination revealed increased iron deposition in the CC of exposed female offspring, but not in males. These findings demonstrate that vulnerability of the brain to air pollution extends to gestation and produces features of several neurodevelopmental disorders in both sexes. Further, they highlight the importance of the commonalities of components of particulate matter exposures as a source of neurotoxicity and common CNS alterations. © The Author 2017. Published by Oxford University Press on behalf of the Society of Toxicology. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Association of modeled long-term personal exposure to ultrafine particles with inflammatory and coagulation biomarkers.

PubMed

Lane, Kevin J; Levy, Jonathan I; Scammell, Madeleine K; Peters, Junenette L; Patton, Allison P; Reisner, Ellin; Lowe, Lydia; Zamore, Wig; Durant, John L; Brugge, Doug

2016-01-01

Long-term exposure to fine particulate matter has been linked to cardiovascular disease and systemic inflammatory responses; however, evidence is limited regarding the effects of long-term exposure to ultrafine particulate matter (UFP, <100nm). We used a cross-sectional study design to examine the association of long-term exposure to near-highway UFP with measures of systemic inflammation and coagulation. We analyzed blood samples from 408 individuals aged 40-91years living in three near-highway and three urban background areas in and near Boston, Massachusetts. We conducted mobile monitoring of particle number concentration (PNC) in each area, and used the data to develop and validate highly resolved spatiotemporal (hourly, 20m) PNC regression models. These models were linked with participant time-activity data to determine individual time-activity adjusted (TAA) annual average PNC exposures. Multivariable regression modeling and stratification were used to assess the association between TAA-PNC and single peripheral blood measures of high-sensitivity C-reactive protein (hsCRP), interleukin-6 (IL-6), tumor-necrosis factor alpha receptor II (TNFRII) and fibrinogen. After adjusting for age, sex, education, body mass index, smoking and race/ethnicity, an interquartile-range (10,000particles/cm(3)) increase in TAA-PNC had a positive non-significant association with a 14.0% (95% CI: -4.6%, 36.2%) positive difference in hsCRP, an 8.9% (95% CI: -0.4%, 10.9%) positive difference in IL-6, and a 5.1% (95% CI: -0.4%, 10.9%) positive difference in TNFRII. Stratification by race/ethnicity revealed that TAA-PNC had larger effect estimates for all three inflammatory markers and was significantly associated with hsCRP and TNFRII in white non-Hispanic, but not East Asian participants. Fibrinogen had a negative non-significant association with TAA-PNC. Our findings suggest an association between annual average near-highway TAA-PNC and subclinical inflammatory markers of CVD risk. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Ambient ultrafine particles activate human monocytes: Effect of dose, differentiation state and age of donors.

PubMed

Bliss, Bishop; Tran, Kevin Ivan; Sioutas, Constantinos; Campbell, Arezoo

2018-02-01

Exposure to ambient particulate matter (PM) has been linked to adverse pulmonary and cardiovascular health effects. Activation of both inflammatory and oxidative stress pathways has been observed and may be a probable cause of these outcomes. We tested the hypothesis that in human monocytes, PM-induced oxidative and inflammatory responses are interrelated. A human monocytic cell line (THP-1) was used to determine if dose and differentiation state plays a role in the cellular response after a 24hr exposure to particles. Primary human monocytes derived from eight female, non-smoker donors (aged: 21, 24, 27, 28, 48, 49, 54 & 60yo) were used to determine if the age of donors modulates the response. Cells were treated with aqueous suspensions of ambient ultrafine particles (UFP, defined as smaller than 0.2µm in size) or a media control for 24hr. After exposure, reactive oxygen species (ROS) formation was increased irrespective of dose or differentiation state of THP-1 cells. In the primary human monocytes, ROS formation was not significantly changed. The release of the proinflammatory cytokine, tumor necrosis factor alpha (TNF-α), was dose-dependent and greatest in differentiated compared to undifferentiated THP-1 cells exposed to UFP. In the Primary human monocytes, TNF-α secretion was increased irrespective of the age of the donor. Our results suggest that after a 24hr exposure to particles, general reactive oxygen species formation was nonspecific and uncorrelated to cytokine secretion which was consistently enhanced. Cytokines play an important role in orchestrating many immune responses and thus the ability of ambient particles to enhance robust secretion of a proinflammatory cytokine from primary human monocytes, and how this may influence the response to pathogens and alter disease states, needs to be further evaluated. Copyright © 2017 Elsevier Inc. All rights reserved.

Comparison of carcinogen, carbon monoxide, and ultrafine particle emissions from narghile waterpipe and cigarette smoking: Sidestream smoke measurements and assessment of second-hand smoke emission factors

PubMed Central

Daher, Nancy; Saleh, Rawad; Jaroudi, Ezzat; Sheheitli, Hiba; Badr, Thérèse; Sepetdjian, Elizabeth; Al Rashidi, Mariam; Saliba, Najat; Shihadeh, Alan

2009-01-01

The lack of scientific evidence on the constituents, properties, and health effects of second-hand waterpipe smoke has fueled controversy over whether public smoking bans should include the waterpipe. The purpose of this study was to investigate and compare emissions of ultrafine particles (UFP, <100 nm), carcinogenic polyaromatic hydrocarbons (PAH), volatile aldehydes, and carbon monoxide (CO) for cigarettes and narghile (shisha, hookah) waterpipes. These smoke constituents are associated with a variety of cancers, and heart and pulmonary diseases, and span the volatility range found in tobacco smoke. Sidestream cigarette and waterpipe smoke was captured and aged in a 1 m3 Teflon-coated chamber operating at 1.5 air changes per hour (ACH). The chamber was characterized for particle mass and number surface deposition rates. UFP and CO concentrations were measured online using a fast particle spectrometer (TSI 3090 Engine Exhaust Particle Sizer), and an indoor air quality monitor. Particulate PAH and gaseous volatile aldehydes were captured on glass fiber filters and DNPH-coated SPE cartridges, respectively, and analyzed off-line using GC–MS and HPLC–MS. PAH compounds quantified were the 5- and 6-ring compounds of the EPA priority list. Measured aldehydes consisted of formaldehyde, acetaldehyde, acrolein, methacrolein, and propionaldehyde. We found that a single waterpipe use session emits in the sidestream smoke approximately four times the carcinogenic PAH, four times the volatile aldehydes, and 30 times the CO of a single cigarette. Accounting for exhaled mainstream smoke, and given a habitual smoker smoking rate of 2 cigarettes per hour, during a typical one-hour waterpipe use session a waterpipe smoker likely generates ambient carcinogens and toxicants equivalent to 2–10 cigarette smokers, depending on the compound in question. There is therefore good reason to include waterpipe tobacco smoking in public smoking bans. PMID:20161525

Air Pollution Exposures and Circulating Biomarkers of Effect in a Susceptible Population: Clues to Potential Causal Component mixtures and mechanisms

PubMed Central

Delfino, Ralph J.; Staimer, Norbert; Tjoa, Thomas; Gillen, Daniel L.; Polidori, Andrea; Arhami, Mohammad; Kleinman, Micheal T.; Vaziri, Nosratola D.; Longhurst, John; Sioutas, Constantinos

2009-01-01

Background Mechanisms involving oxidative stress and inflammation have been proposed to explain associations of ambient air pollution with cardiovascular morbidity and mortality. Experimental evidence suggests that organic components and ultrafine particles (UFP) are important. Methods We conducted a panel study of 60 elderly subjects with coronary artery disease living in retirement communities within the Los Angeles, California, air basin. Weekly biomarkers of inflammation included plasma interleukin-6, tumor necrosis factor-α soluble receptor II (sTNF-RII), soluble platelet selectin (sP-selectin), and C-reactive protein (CRP). Biomarkers of erythrocyte antioxidant activity included glutathione peroxidase-1 and superoxide dismutase. Exposures included outdoor home daily particle mass [particulate matter < 0.25, 0.25–2.5, and 2.5–10 μm in aerodynamic diameter (PM0.25, PM0.25–2.5, PM2.5–10)], and hourly elemental and black carbon (EC–BC), estimated primary and secondary organic carbon (OCpri, SOC), particle number (PN), carbon monoxide (CO), and nitrogen oxides–nitrogen dioxide (NOx–NO2). We analyzed the relation of biomarkers to exposures with mixed effects models adjusted for potential confounders. Results Primary combustion markers (EC–BC, OCpri, CO, NOx–NO2), but not SOC, were positively associated with inflammatory biomarkers and inversely associated with erythrocyte anti-oxidant enzymes (n = 578). PN and PM0.25 were more strongly associated with biomarkers than PM0.25–2.5. Associations for all exposures were stronger during cooler periods when only OCpri, PN, and NOx were higher. We found weaker associations with statin (sTNF-RII, CRP) and clopidogrel use (sP-selectin). Conclusions Traffic-related air pollutants are associated with increased systemic inflammation, increased platelet activation, and decreased erythrocyte antioxidant enzyme activity, which may be partly behind air pollutant–related increases in systemic inflammation. Differences in association by particle size, OC fraction, and seasonal period suggest components carried by UFP are important. PMID:19672402

Exposure to fine and ultrafine particles from secondhand smoke in public places before and after the smoking ban, Italy 2005.

PubMed

Valente, Pasquale; Forastiere, Francesco; Bacosi, Antonella; Cattani, Giorgio; Di Carlo, Simonetta; Ferri, Monica; Figà-Talamanca, Irene; Marconi, Achille; Paoletti, Luigi; Perucci, Carlo; Zuccaro, Piergiorgio

2007-10-01

A smoking ban in all indoor public places was enforced in Italy on 10 January 2005. We compared indoor air quality before and after the smoking ban by monitoring the indoor concentrations of fine (<2.5 microm diameter, PM2.5) and ultrafine particulate matter (<0.1 microm diameter, UFP). PM2.5 and ultrafine particles were measured in 40 public places (14 bars, six fast food restaurants, eight restaurants, six game rooms, six pubs) in Rome, before and after the introduction of the law banning smoking (after 3 and 12 months). Measurements were taken using real time particle monitors (DustTRAK Mod. 8520 TSI; Ultra-fine Particles Counter-TRAK Model 8525 TSI). The PM2.5 data were scaled using a correction equation derived from a comparison with the reference method (gravimetric measurement). The study was completed by measuring urinary cotinine, and pre-law and post-law enforcement among non-smoking employees at these establishments In the post-law period, PM2.5 decreased significantly from a mean concentration of 119.3 microg/m3 to 38.2 microg/m3 after 3 months (p<0.005), and then to 43.3 microg/m3 a year later (p<0.01). The UFP concentrations also decreased significantly from 76,956 particles/cm3 to 38,079 particles/cm3 (p<0.0001) and then to 51,692 particles/cm3 (p<0.01). Similarly, the concentration of urinary cotinine among non-smoking workers decreased from 17.8 ng/ml to 5.5 ng/ml (p<0.0001) and then to 3.7 ng/ml (p<0.0001). The application of the smoking ban led to a considerable reduction in the exposure to indoor fine and ultrafine particles in hospitality venues, confirmed by a contemporaneous reduction of urinary cotinine.

Subclinical responses in healthy cyclists briefly exposed to traffic-related air pollution: an intervention study

PubMed Central

2010-01-01

Background Numerous epidemiological studies have demonstrated adverse health effects of a sedentary life style, on the one hand, and of acute and chronic exposure to traffic-related air pollution, on the other. Because physical exercise augments the amount of inhaled pollutants, it is not clear whether cycling to work in a polluted urban environment should be encouraged or not. To address this conundrum we investigated if a bicycle journey along a busy commuting road would induce changes in biomarkers of pulmonary and systematic inflammation in a group of healthy subjects. Methods 38 volunteers (mean age: 43 ± 8.6 years, 26% women) cycled for about 20 minutes in real traffic near a major bypass road (road test; mean UFP exposure: 28,867 particles per cm3) in Antwerp and in a laboratory with filtered air (clean room; mean UFP exposure: 496 particles per cm3). The exercise intensity (heart rate) and duration of cycling were similar for each volunteer in both experiments. Exhaled nitric oxide (NO), plasma interleukin-6 (IL-6), platelet function, Clara cell protein in serum and blood cell counts were measured before and 30 minutes after exercise. Results Percentage of blood neutrophils increased significantly more (p = 0.004) after exercise in the road test (3.9%; 95% CI: 1.5 to 6.2%; p = 0.003) than after exercise in the clean room (0.2%; 95% CI: -1.8 to 2.2%, p = 0.83). The pre/post-cycling changes in exhaled NO, plasma IL-6, platelet function, serum levels of Clara cell protein and number of total blood leukocytes did not differ significantly between the two scenarios. Conclusions Traffic-related exposure to particles during exercise caused a small increase in the distribution of inflammatory blood cells in healthy subjects. The health significance of this isolated change is unclear. PMID:20973949

Subclinical responses in healthy cyclists briefly exposed to traffic-related air pollution: an intervention study.

PubMed

Jacobs, Lotte; Nawrot, Tim S; de Geus, Bas; Meeusen, Romain; Degraeuwe, Bart; Bernard, Alfred; Sughis, Muhammad; Nemery, Benoit; Panis, Luc Int

2010-10-25

Numerous epidemiological studies have demonstrated adverse health effects of a sedentary life style, on the one hand, and of acute and chronic exposure to traffic-related air pollution, on the other. Because physical exercise augments the amount of inhaled pollutants, it is not clear whether cycling to work in a polluted urban environment should be encouraged or not. To address this conundrum we investigated if a bicycle journey along a busy commuting road would induce changes in biomarkers of pulmonary and systematic inflammation in a group of healthy subjects. 38 volunteers (mean age: 43 ± 8.6 years, 26% women) cycled for about 20 minutes in real traffic near a major bypass road (road test; mean UFP exposure: 28,867 particles per cm3) in Antwerp and in a laboratory with filtered air (clean room; mean UFP exposure: 496 particles per cm3). The exercise intensity (heart rate) and duration of cycling were similar for each volunteer in both experiments. Exhaled nitric oxide (NO), plasma interleukin-6 (IL-6), platelet function, Clara cell protein in serum and blood cell counts were measured before and 30 minutes after exercise. Percentage of blood neutrophils increased significantly more (p = 0.004) after exercise in the road test (3.9%; 95% CI: 1.5 to 6.2%; p = 0.003) than after exercise in the clean room (0.2%; 95% CI: -1.8 to 2.2%, p = 0.83). The pre/post-cycling changes in exhaled NO, plasma IL-6, platelet function, serum levels of Clara cell protein and number of total blood leukocytes did not differ significantly between the two scenarios. Traffic-related exposure to particles during exercise caused a small increase in the distribution of inflammatory blood cells in healthy subjects. The health significance of this isolated change is unclear.

Comparison of carcinogen, carbon monoxide, and ultrafine particle emissions from narghile waterpipe and cigarette smoking: Sidestream smoke measurements and assessment of second-hand smoke emission factors

NASA Astrophysics Data System (ADS)

Daher, Nancy; Saleh, Rawad; Jaroudi, Ezzat; Sheheitli, Hiba; Badr, Thérèse; Sepetdjian, Elizabeth; Al Rashidi, Mariam; Saliba, Najat; Shihadeh, Alan

2010-01-01

The lack of scientific evidence on the constituents, properties, and health effects of second-hand waterpipe smoke has fueled controversy over whether public smoking bans should include the waterpipe. The purpose of this study was to investigate and compare emissions of ultrafine particles (UFP, <100 nm), carcinogenic polyaromatic hydrocarbons (PAH), volatile aldehydes, and carbon monoxide (CO) for cigarettes and narghile (shisha, hookah) waterpipes. These smoke constituents are associated with a variety of cancers, and heart and pulmonary diseases, and span the volatility range found in tobacco smoke. Sidestream cigarette and waterpipe smoke was captured and aged in a 1 m 3 Teflon-coated chamber operating at 1.5 air changes per hour (ACH). The chamber was characterized for particle mass and number surface deposition rates. UFP and CO concentrations were measured online using a fast particle spectrometer (TSI 3090 Engine Exhaust Particle Sizer), and an indoor air quality monitor. Particulate PAH and gaseous volatile aldehydes were captured on glass fiber filters and DNPH-coated SPE cartridges, respectively, and analyzed off-line using GC-MS and HPLC-MS. PAH compounds quantified were the 5- and 6-ring compounds of the EPA priority list. Measured aldehydes consisted of formaldehyde, acetaldehyde, acrolein, methacrolein, and propionaldehyde. We found that a single waterpipe use session emits in the sidestream smoke approximately four times the carcinogenic PAH, four times the volatile aldehydes, and 30 times the CO of a single cigarette. Accounting for exhaled mainstream smoke, and given a habitual smoker smoking rate of 2 cigarettes per hour, during a typical one-hour waterpipe use session a waterpipe smoker likely generates ambient carcinogens and toxicants equivalent to 2-10 cigarette smokers, depending on the compound in question. There is therefore good reason to include waterpipe tobacco smoking in public smoking bans.

Effects of Particle Filters and Selective Catalytic Reduction on In-Use Heavy-Duty Diesel Truck Emissions

NASA Astrophysics Data System (ADS)

Preble, C.; Cados, T.; Harley, R.; Kirchstetter, T.

2016-12-01

Heavy-duty diesel trucks (HDDT) are a major source of nitrogen oxides (NOx) and black carbon (BC) in urban environments, contributing to persistent ozone and particulate matter air quality problems. Diesel particle filters (DPFs) and selective catalytic reduction (SCR) systems that target PM and NOx emissions, respectively, have recently become standard equipment on new HDDT. DPFs can also be installed on older engines as a retrofit device. Previous work has shown that DPF and SCR systems can reduce NOx and BC emissions by up to 70% and 90%, respectively, compared to modern trucks without these after-treatment controls (Preble et al., ES&T 2015). DPFs can have the undesirable side-effect of increasing ultrafine particle (UFP) and nitrogen dioxide (NO2) emissions. While SCR systems can partially mitigate DPF-related NO2 increases, these systems can emit nitrous oxide (N2O), a potent greenhouse gas. We report new results from a study of HDDT emissions conducted in fall 2015 at the Port of Oakland and Caldecott Tunnel in California's San Francisco Bay Area. We report pollutant emission factors (g kg-1) for emitted NOx, NO2, BC, PM2.5, UFP, and N2O on a truck-by-truck basis. Using a roadside license plate recognition system, we categorize each truck by its engine model year and installed after-treatment controls. From this, we develop emissions profiles for trucks with and without DPF and SCR. We evaluate the effectiveness of these devices as a function of their age to determine whether degradation is an issue. We also compare the emission profiles of trucks traveling at low speeds along a level, arterial road en route to the port and at high speeds up a 4% grade highway approaching the tunnel. Given the climate impacts of BC and N2O, we also examine the global warming potential of emissions from trucks with and without DPF and SCR.

Traffic-related air pollution in the community of San Ysidro, CA, in relation to northbound vehicle wait times at the US-Mexico border Port of Entry

NASA Astrophysics Data System (ADS)

Quintana, Penelope J. E.; Dumbauld, Jill J.; Garnica, Lynelle; Chowdhury, M. Zohir; Velascosoltero, José; Mota-Raigoza, Arturo; Flores, David; Rodríguez, Edgar; Panagon, Nicolas; Gamble, Jamison; Irby, Travis; Tran, Cuong; Elder, John; Galaviz, Vanessa E.; Hoffman, Lisa; Zavala, Miguel; Molina, Luisa T.

2014-05-01

The San Diego/Tijuana US-Mexico border crossing at the San Ysidro Port of Entry (POE) is the world's busiest international land border crossing (GSA, 2013). San Ysidro, California, is the US community immediately adjacent to the border crossing. More than 90% of San Ysidro residents are Hispanic, and the average household income is less than 60% of the San Diego regional average. This study investigated the San Ysidro POE as a source of traffic-related air pollutants in San Ysidro, especially in relation to wind direction and northbound vehicle wait times. The pollutants ultrafine particulate matter (UFP), black carbon (BC), and particulate matter <2.5 μm in diameter (PM2.5) were periodically sampled through the course of 2010 at four rooftop locations: one commercial establishment near the POE, two elementary schools in San Ysidro, and a coastal estuary reference site. Weather data from two nearby sites and northbound border wait times were also collected. Results indicate consistently higher daytime BC and UFP concentrations at the measurement sites near the POE. Pollution concentrations were higher during low wind speeds or when wind was blowing from the POE towards San Ysidro. In February, March and November measurements, black carbon pollution appeared to be significantly positively associated with the POE northbound wait times when the wind direction was blowing from the POE towards San Ysidro or during low wind speeds, but not when the wind direction was from the west/northwest towards the POE. This pilot study is the first to investigate the potential effect of the POE, especially the long northbound traffic delays, on the nearby community of San Ysidro. Disparities in traffic exposures are an environmental justice issue and this should be taken into account during planning and operation of POEs.

The formation of ultrafine iodine particles from coastal macroalgae

NASA Astrophysics Data System (ADS)

McFiggans, G.; Coe, H.; Allan, J. D.; Plane, J. M. C.; Saunders, R.

2003-04-01

We will present the first direct evidence for iodine-containing ultrafine particle (ufp) production from macroalgae in the intertidal zone. Ultrafine particles in the coastal environment have been the subject of intense interest(1,2,3) due to their potentially important contributions to both the direct radiation scattering budget and, by activation to form cloud droplets, to the indirect radiative effect. Based on a variety of laboratory studies, it has recently been proposed that photochemical production of condensable iodine oxides is responsible for their formation(4-9). This work shows that previous studies investigating the mechanisms and kinetics of particle formation due to iodine photochemistry are largely untargeted in that they assume gaseous iodocarbons are the precursor material. Models aiming to simulate coastal new particle formation suffer from the same lack of basic understanding of the formation mechanisms (and indeed precursor identities)(7-9). Following measurements of iodine monoxide(10,11) and iodocarbons(12) in the coastal atmosphere, modelling studies have demonstrated the importance of inorganic iodine in gaseous photochemical cycles(13). Volatile iodocarbons have a number of sources, but intertidal macroalgal beds(14) appear to dominate in the coastal zone(15). However, no direct evidence for a relationship between the macroalgae and iodine-containing particle formation have been reported. During the NERC-funded NAMBLEX field project at Mace Head on the west coast of Ireland in August 2002, we conducted a series of experiments on macroalgae in the intertidal zone. A reactor containing Laminaria digitata cropped from an intertidal rock pool was exposed to an ozonised stream of initially particle-free air. Using a scanning mobility particle sizer (SMPS) to sample the reactor output, it was found that extremely large numbers of particles were formed. By increasing the exposure time to the airstream, the particles were allowed to grow above the detection threshold of an aerosol mass spectrometer (AMS). It was found that the dominant m/z fragments above 100 Daltons at all sizes of particle were derived from iodine-containing species, but the mass spectrum exhibited significant differences from that reported for particles generated in the laboratory from iodocarbon photolysis(5,6). Subsequent experiments at UMIST have found a similar response from the related and more widespread macroalga Laminaria hyperborea. In addition, further results from the laboratory program investigating ufp formation from both inorganic and organic precursor molecules will be presented and discussed to aid mechanistic interpretation of the release of ufps from macroalgae. 1. O’Dowd et al., GRL, 1707-1710, 1999, 2. Coe et al., JGR, 26891-26905, 2000, 3. Kolb, Nature, 597-598, 2002, 4. Hoffmann et al., GRL, 1949-1952, 2001, 5. O’Dowd et al., Nature, 632-636, 2002, 6. Jimenez et al., JGR in press, 2003, 7. McFiggans et al., EGS presentation, 2002, 8. McFiggans, CERC3 presentation, 2002, 9. McFiggans et al., 2003, in prep, 10. Alicke et al., Nature, 572-573, 1999, 11. Allan et al., JGR, 14363-14369, 2000, 12. Carpenter et al., JGR, 1679-1689, 1999, 13. McFiggans et al., JGR, 14371-14385, 2000, 14. Carpenter et al., GBC, 1191-1204, 2000, 15. Carpenter et al., ACP, 9-18, 2001.

Membrane technology for treating of waste nanofluids coolant: A review

NASA Astrophysics Data System (ADS)

Mohruni, Amrifan Saladin; Yuliwati, Erna; Sharif, Safian; Ismail, Ahmad Fauzi

2017-09-01

The treatment of cutting fluids wastes concerns a big number of industries, especially from the machining operations to foster environmental sustainability. Discharging cutting fluids, waste through separation technique could protect the environment and also human health in general. Several methods for the separation emulsified oils or oily wastewater have been proposed as three common methods, namely chemical, physicochemical and mechanical and membrane technology application. Membranes are used into separate and concentrate the pollutants in oily wastewater through its perm-selectivity. Meanwhile, the desire to compensate for the shortcomings of the cutting fluid media in a metal cutting operation led to introduce the using of nanofluids (NFs) in the minimum quantity lubricant (MQL) technique. NFs are prepared based on nanofluids technology by dispersing nanoparticles (NPs) in liquids. These fluids have potentially played to enhance the performance of traditional heat transfer fluids. Few researchers have studied investigation of the physical-chemical, thermo-physical and heat transfer characteristics of NFs for heat transfer applications. The use of minimum quantity lubrication (MQL) technique by NFs application is developed in many metal cutting operations. MQL did not only serve as a better alternative to flood cooling during machining operation and also increases better-finished surface, reduces impact loads on the environment and fosters environmental sustainability. Waste coolant filtration from cutting tools using membrane was treated by the pretreated process, coagulation technique and membrane filtration. Nanomaterials are also applied to modify the membrane structure and morphology. Polyvinylidene fluoride (PVDF) is the better choice in coolant wastewater treatment due to its hydrophobicity. Using of polyamide nanofiltration membranes BM-20D and UF-PS-100-100, 000, it resulted in the increase of permeability of waste coolant filtration. Titanium dioxide is nanomaterials additive to modify the Nanopores of the surface membrane. Contact angle and average pore size were used in the investigation of the surface morphology of membranes. An adequate choice in modifying the membrane surface in waste coolant filtration may bring a promised alternative as a solution in waste coolant remediation.

Maine CITE: Technology Collaboration through Distance Learning.

ERIC Educational Resources Information Center

Stockford, David Noble; And Others

This paper describes the Maine Consumer Information and Technology Training Exchange (Maine CITE) project designed to increase the availability and use of assistive-technology to Maine people with disabilities. Maine CITE is a 3-year project supported by the Maine Department of Education, Division of Special Education, with a grant from the…

Is LLLT effective in the management of TMJ pain?

NASA Astrophysics Data System (ADS)

Pinheiro, Antonio L. B.; Manzi, Cecilia T.; Rolim, Aluizio B.; Vieira, Alessandro L. B.

1999-05-01

This paper reports the result of the use of LLLT on the treatment of TMJ pain and present LLLT as an effective method of treating such problem. One hundred and eighty one female and 23 male patients aged between 7 and 81 years old (average 36.9 years old) suffering TMJ pain were treated with 632.8, 670, and 830nm diodes lasers at the Laser Center of the UFPE. The treatment consisted of a series of 12 applications twice a week. Patients were treated with an average dose of 3 J/cm2. One hundred forty one out of 204 patients were asymptomatic at the end of the treatment, 37 improved considerably and 26 were symptomatic. These result show although LLLT does not cure TMJ disorders it is effective in reducing TMJ pain.

Evaluation of a LiF:Mg,Ti thermoluminescent ring dosimeter according to the IEC 62387:2012 Standards

NASA Astrophysics Data System (ADS)

Oliveira, Edyelle L. B.; de Barros, Vinícius S. M.; Asfora, Viviane K.; Khoury, Helen J.

2018-03-01

This work shows results of type testing of a ring radiation dosimeter system under IEC 62387:2012. The personal dosimeter investigated in this work consists of a commercial one element plastic ring which contains an LiF:Mg,Ti thermoluminescent pellet. By applying requirements for statistical fluctuations and linearity, a minimum measurable dose in Hp(0.07) was established. Energy and angular dependence aided in determining energy correction factors and fading requirements were used to select the most appropriate preheat scheme. Type testing of passive radiation monitors was performed in the Radiation Metrology Laboratory (LMRI-DEN/UFPE) of the Federal University of Pernambuco and is a major step in Brazil for the independent evaluation of these dosimeters, currently not available in the country.

IMPROVEMENT OF WATER MAIN INSPECTION TECHNOLOGY

EPA Science Inventory

This document is a handout of a slide presentation that addresses improvement of water main inspection technology. The slide presentation addresses the need for improved inspection technology (e.g., 237,000 main breaks/yr); the limits on main break prevention; and, the adverse ...

Two-way effect modifications of air pollution and air temperature on total natural and cardiovascular mortality in eight European urban areas.

PubMed

Chen, Kai; Wolf, Kathrin; Breitner, Susanne; Gasparrini, Antonio; Stafoggia, Massimo; Samoli, Evangelia; Andersen, Zorana Jovanovic; Bero-Bedada, Getahun; Bellander, Tom; Hennig, Frauke; Jacquemin, Bénédicte; Pekkanen, Juha; Hampel, Regina; Cyrys, Josef; Peters, Annette; Schneider, Alexandra

2018-07-01

Although epidemiological studies have reported associations between mortality and both ambient air pollution and air temperature, it remains uncertain whether the mortality effects of air pollution are modified by temperature and vice versa. Moreover, little is known on the interactions between ultrafine particles (diameter ≤ 100 nm, UFP) and temperature. We investigated whether the short-term associations of particle number concentration (PNC in the ultrafine range (≤100 nm) or total PNC ≤ 3000 nm, as a proxy for UFP), particulate matter ≤ 2.5 μm (PM 2.5 ) and ≤ 10 μm (PM 10 ), and ozone with daily total natural and cardiovascular mortality were modified by air temperature and whether air pollution levels affected the temperature-mortality associations in eight European urban areas during 1999-2013. We first analyzed air temperature-stratified associations between air pollution and total natural (nonaccidental) and cardiovascular mortality as well as air pollution-stratified temperature-mortality associations using city-specific over-dispersed Poisson additive models with a distributed lag nonlinear temperature term in each city. All models were adjusted for long-term and seasonal trend, day of the week, influenza epidemics, and population dynamics due to summer vacation and holidays. City-specific effect estimates were then pooled using random-effects meta-analysis. Pooled associations between air pollutants and total and cardiovascular mortality were overall positive and generally stronger at high relatively compared to low air temperatures. For example, on days with high air temperatures (>75th percentile), an increase of 10,000 particles/cm 3 in PNC corresponded to a 2.51% (95% CI: 0.39%, 4.67%) increase in cardiovascular mortality, which was significantly higher than that on days with low air temperatures (<25th percentile) [-0.18% (95% CI: -0.97%, 0.62%)]. On days with high air pollution (>50th percentile), both heat- and cold-related mortality risks increased. Our findings showed that high temperature could modify the effects of air pollution on daily mortality and high air pollution might enhance the air temperature effects. Copyright © 2018 Elsevier Ltd. All rights reserved.

Variation and co-variation of PM10, particle number concentration, NOx and NO2 in the urban air - Relationships with wind speed, vertical temperature gradient and weather type

NASA Astrophysics Data System (ADS)

Grundström, M.; Hak, C.; Chen, D.; Hallquist, M.; Pleijel, H.

2015-11-01

Atmospheric ultrafine particles (UFP; diameter < 0.1 μm) represent a growing global health concern in urban environments and has a strong link to traffic related emissions. UFP is usually the dominating fraction of atmospheric particle number concentrations (PNC) despite being a minor part of total particle mass. The aim of this study was to empirically investigate the relationship between PNC and other air pollutants (NOX, NO2 and PM10) in the urban environment and their dependence on meteorology and weather type, using the Lamb Weather Type (LWT) classification scheme. The study was carried out in Gothenburg, Sweden, at an urban background site during April 2007-May 2008. It was found that daily average [PNC] correlated very well with [NOx] (R2 = 0.73) during inversion days, to a lesser extent with [NO2] (R2 = 0.58) and poorly with [PM10] (R2 = 0.07). Both PNC and NOx had similar response patterns to wind speed and to the strength of temperature inversions. PNC displayed two regimes, one strongly correlated to NOx and a second poorly correlated to NOx which was characterised by high wind speed. For concentration averages based on LWTs, the PNC-[NOx] relationship remained strong (R2 = 0.70) where the windy LWT W deviated noticeably. Exclusion of observations with wind speed >5 ms-1 or ΔT < 0 °C from LWTs produced more uniform and stronger relationships (R2 = 0.90; R2 = 0.93). Low wind speeds and positive vertical temperature gradients were most common during LWTs A, NW, N and NE. These weather types were also associated with the highest daily means of NOx (∼30 ppb) and PNC (∼10 000 # cm-3). A conclusion from this study is that NOx (but not PM10) is a good proxy for PNC especially during calm and stable conditions and that LWTs A, NW, N and NE are high risk weather types for elevated NOx and PNC.

Temporal evolution of ultrafine particles and of alveolar deposited surface area from main indoor combustion and non-combustion sources in a model room.

PubMed

Manigrasso, Maurizio; Vitali, Matteo; Protano, Carmela; Avino, Pasquale

2017-11-15

Aerosol number size distributions, PM mass concentrations, alveolar deposited surface areas (ADSAs) and VOC concentrations were measured in a model room when aerosol was emitted by sources frequently encountered in indoor environments. Both combustion and non-combustion sources were considered. The most intense aerosol emission occurred when combustion sources were active (as high as 4.1×10 7 particlescm -3 for two meat grilling sessions; the first with exhaust ventilation, the second without). An intense spike generation of nucleation particles occurred when appliances equipped with brush electric motors were operating (as high as 10 6 particlescm -3 on switching on an electric drill). Average UFP increments over the background value were highest for electric appliances (5-12%) and lowest for combustion sources (as low as -24% for tobacco cigarette smoke). In contrast, average increments in ADSA were highest for combustion sources (as high as 3.2×10 3 μm 2 cm -3 for meat grilling without exhaust ventilation) and lowest for electric appliances (20-90μm 2 cm -3 ). The health relevance of such particles is associated to their ability to penetrate cellular structures and elicit inflammatory effects mediated through oxidative stress in a way dependent on their surface area. The highest VOC concentrations were measured (PID probe) for cigarette smoke (8ppm) and spray air freshener (10ppm). The highest PM mass concentration (PM 1 ) was measured for citronella candle burning (as high as 7.6mgm -3 ). Copyright © 2017 Elsevier B.V. All rights reserved.

Activation of the nociceptin/orphanin FQ receptor reduces bronchoconstriction and microvascular leakage in a rabbit model of gastroesophageal reflux

PubMed Central

D'Agostino, Bruno; Marrocco, Giuseppina; De Nardo, Marilisa; Calò, Girolamo; Guerrini, Remo; Gallelli, Luca; Advenier, Charles; Rossi, Francesco

2005-01-01

Nociceptin/orphanin FQ (N/OFQ) is the endogenous peptide ligand for a specific G-protein coupled receptor, the N/OFQ peptide receptor (NOP). The N/OFQ-NOP receptor system has been reported to play an important role in pain, anxiety and appetite regulation. In airways, N/OFQ was found to inhibit the release of tachykinins and the bronchoconstriction and cough provoked by capsaicin. Here we evaluated the effects of NOP receptor activation in bronchoconstriction and airway microvascular leakage induced by intraesophageal (i.oe.) hydrochloric acid (HCl) instillation in rabbits. We also tested the effects of NOP receptor activation in SP-induced plasma extravasation and bronchoconstriction. In anesthetized New Zealand rabbits bronchopulmonary function (total lung resistance (RL) and dynamic compliance (Cdyn)) and airway microvascular leakage (extravasation of Evans blue dye) were evaluated. Infusion of i.oe. HCl (1 N) led to a significant increase in bronchoconstriction and plasma extravasation in the main bronchi and trachea of rabbits pretreated with propranolol, atropine and phosphoramidon. Bronchoconstriction and airway microvascular leakage were inhibited by N/OFQ (3–30 μg kg−1 i.v.) in a dose-dependent manner. The NOP receptor agonist [Arg14,Lys15]N/OFQ mimicked the inhibitory effect of N/OFQ, being 10-fold more potent, UFP-101, a peptide selective NOP receptor antagonist, blocked the inhibitory effects of both agonists. Under the same experimental conditions, N/OFQ and [Arg14,Lys15]N/OFQ did not counteract the bronchoconstriction and airway microvascular leakage induced by substance P. These results suggest that bronchoconstriction and airway plasma extravasation induced by i.oe. HCl instillation are inhibited by activation of prejunctional NOP receptors. PMID:15685213

Main mental disorders in crack-cocaine users treated at Psychosocial Care Centers for Alcohol and Drugs in the city of Recife, Brazil.

PubMed

Castro, Antonio Gomes de; Silva, Diego César Nunes da; Figueiroa, Magda da Silva

2016-01-01

Brazil's Northeast region has the highest crack-cocaine consumption in the country. Crack-cocaine has more intense effects than cocaine powder and can cause greater chemical dependence. Psychosocial Care Centers for Alcohol and Drugs (CAPSad) are public health services that provide treatment for drug dependence. It is common for drug users, and particularly crack-cocaine users, to develop mental disorders. Objective: To evaluate the most common mental disorders in crack-cocaine dependents in treatment at CAPSad in the city of Recife, Brazil. The research database "Between rocks and shots: user profiles, consumption strategies, and social impact of crack cocaine" (CEP/CCS/UFPE no. 206/11) was consulted to establish the areas of crack cocaine consumption in the city of Recife. There were 885 patients in treatment for crack-cocaine use, with a mean age of 29.8±9.4 years. The mean duration of drug use was 6.1±4.6 years. Most of the patients were males (80.3%), had left school at some point between the 1st and 9th grades (45.6%), were unemployed and/or seeking employment (52%) and used drugs daily (56.4%). Cocaine chemical dependence was more significant when correlated with use of crack-cocaine and other drugs such as medications and hallucinogens (p = 0.01). Data from this study showed strong associations between crack-cocaine uses and development of mental disorders, particularly when abuse of multiple substances occurs. Based on these data, there is a clear need for coordination of related public policies for support and social reintegration to provide these people with comprehensive care.

Association between Traffic-Related Air Pollution in Schools and Cognitive Development in Primary School Children: A Prospective Cohort Study

PubMed Central

Sunyer, Jordi; Esnaola, Mikel; Alvarez-Pedrerol, Mar; Forns, Joan; Rivas, Ioar; López-Vicente, Mònica; Suades-González, Elisabet; Foraster, Maria; Garcia-Esteban, Raquel; Basagaña, Xavier; Viana, Mar; Cirach, Marta; Moreno, Teresa; Alastuey, Andrés; Sebastian-Galles, Núria; Nieuwenhuijsen, Mark; Querol, Xavier

2015-01-01

Background Air pollution is a suspected developmental neurotoxicant. Many schools are located in close proximity to busy roads, and traffic air pollution peaks when children are at school. We aimed to assess whether exposure of children in primary school to traffic-related air pollutants is associated with impaired cognitive development. Methods and Findings We conducted a prospective study of children (n = 2,715, aged 7 to 10 y) from 39 schools in Barcelona (Catalonia, Spain) exposed to high and low traffic-related air pollution, paired by school socioeconomic index; children were tested four times (i.e., to assess the 12-mo developmental trajectories) via computerized tests (n = 10,112). Chronic traffic air pollution (elemental carbon [EC], nitrogen dioxide [NO2], and ultrafine particle number [UFP; 10–700 nm]) was measured twice during 1-wk campaigns both in the courtyard (outdoor) and inside the classroom (indoor) simultaneously in each school pair. Cognitive development was assessed with the n-back and the attentional network tests, in particular, working memory (two-back detectability), superior working memory (three-back detectability), and inattentiveness (hit reaction time standard error). Linear mixed effects models were adjusted for age, sex, maternal education, socioeconomic status, and air pollution exposure at home. Children from highly polluted schools had a smaller growth in cognitive development than children from the paired lowly polluted schools, both in crude and adjusted models (e.g., 7.4% [95% CI 5.6%–8.8%] versus 11.5% [95% CI 8.9%–12.5%] improvement in working memory, p = 0.0024). Cogently, children attending schools with higher levels of EC, NO2, and UFP both indoors and outdoors experienced substantially smaller growth in all the cognitive measurements; for example, a change from the first to the fourth quartile in indoor EC reduced the gain in working memory by 13.0% (95% CI 4.2%–23.1%). Residual confounding for social class could not be discarded completely; however, the associations remained in stratified analyses (e.g., for type of school or high-/low-polluted area) and after additional adjustments (e.g., for commuting, educational quality, or smoking at home), contradicting a potential residual confounding explanation. Conclusions Children attending schools with higher traffic-related air pollution had a smaller improvement in cognitive development. PMID:25734425

Impacts of Aging Emission Control Systems on In-Use Heavy-Duty Diesel Truck Emission Rates

NASA Astrophysics Data System (ADS)

Preble, C.; Cados, T.; Harley, R.; Kirchstetter, T.

2017-12-01

Heavy-duty diesel trucks are a major source of nitrogen oxides (NOx) and black carbon (BC) in urban environments, contributing to persistent ozone and particulate matter air quality problems. Recently, diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems have become standard equipment on new trucks. Particle filters can also be installed as a retrofit on older engines. Prior work has shown that exhaust filters and SCR systems effectively reduce BC and NOx emission rates by up to 90 and 80%, respectively (Preble et al., ES&T 2015). There is concern, however, that DPFs may promote the formation of ultrafine particles (UFP) and increase tailpipe emissions of nitrogen dioxide (NO2). Additionally, urea-based SCR systems for NOx control may form nitrous oxide (N2O), an important contributor to stratospheric ozone depletion. The effectiveness of these emission controls has been thoroughly evaluated in the laboratory, but the long-term durability of in-use systems and their impacts on co-emitted species have not been well characterized. To evaluate the in-use performance of DPF and SCR systems, pollutant emissions from thousands of diesel trucks were measured over several years at the Port of Oakland and the Caldecott Tunnel in the San Francisco Bay Area. Pollutants present in the exhaust plumes of individual trucks were measured at high time resolution (≥1 Hz) as trucks passed under a mobile lab stationed on an overpass. Fuel-based emission factors (g pollutant emitted per kg fuel burned) were calculated for individual trucks and linked via recorded license plates to vehicle attributes, including engine model year and installed emission control systems. Use of DPFs reduced the BC emission rate by up to 95% at both locations. SCR systems were more effective at reducing NOx emissions under the uphill, highway driving conditions at the Caldecott Tunnel. The emission rates of co-emitted species NO2, UFP, and N2O depended on driving mode. Some DPFs on trucks with 2007-2009 model year engines showed deterioration or failure in filter performance, leading to higher BC emission rates compared to the average for trucks without filters. Emission inventories may underestimate total on-road emissions from diesel trucks, especially if particle filter failure rates continue to increase over time.

Association between traffic-related air pollution in schools and cognitive development in primary school children: a prospective cohort study.

PubMed

Sunyer, Jordi; Esnaola, Mikel; Alvarez-Pedrerol, Mar; Forns, Joan; Rivas, Ioar; López-Vicente, Mònica; Suades-González, Elisabet; Foraster, Maria; Garcia-Esteban, Raquel; Basagaña, Xavier; Viana, Mar; Cirach, Marta; Moreno, Teresa; Alastuey, Andrés; Sebastian-Galles, Núria; Nieuwenhuijsen, Mark; Querol, Xavier

2015-03-01

Air pollution is a suspected developmental neurotoxicant. Many schools are located in close proximity to busy roads, and traffic air pollution peaks when children are at school. We aimed to assess whether exposure of children in primary school to traffic-related air pollutants is associated with impaired cognitive development. We conducted a prospective study of children (n = 2,715, aged 7 to 10 y) from 39 schools in Barcelona (Catalonia, Spain) exposed to high and low traffic-related air pollution, paired by school socioeconomic index; children were tested four times (i.e., to assess the 12-mo developmental trajectories) via computerized tests (n = 10,112). Chronic traffic air pollution (elemental carbon [EC], nitrogen dioxide [NO2], and ultrafine particle number [UFP; 10-700 nm]) was measured twice during 1-wk campaigns both in the courtyard (outdoor) and inside the classroom (indoor) simultaneously in each school pair. Cognitive development was assessed with the n-back and the attentional network tests, in particular, working memory (two-back detectability), superior working memory (three-back detectability), and inattentiveness (hit reaction time standard error). Linear mixed effects models were adjusted for age, sex, maternal education, socioeconomic status, and air pollution exposure at home. Children from highly polluted schools had a smaller growth in cognitive development than children from the paired lowly polluted schools, both in crude and adjusted models (e.g., 7.4% [95% CI 5.6%-8.8%] versus 11.5% [95% CI 8.9%-12.5%] improvement in working memory, p = 0.0024). Cogently, children attending schools with higher levels of EC, NO2, and UFP both indoors and outdoors experienced substantially smaller growth in all the cognitive measurements; for example, a change from the first to the fourth quartile in indoor EC reduced the gain in working memory by 13.0% (95% CI 4.2%-23.1%). Residual confounding for social class could not be discarded completely; however, the associations remained in stratified analyses (e.g., for type of school or high-/low-polluted area) and after additional adjustments (e.g., for commuting, educational quality, or smoking at home), contradicting a potential residual confounding explanation. Children attending schools with higher traffic-related air pollution had a smaller improvement in cognitive development.

Primary School Students' Views about Science, Technology and Engineering

ERIC Educational Resources Information Center

Pekmez, Esin

2018-01-01

Some of the main goals of science education are to increase students' knowledge about the technology and engineering design process, and to train students as scientifically and technologically literate individuals. The main purpose of this study is to find out primary students' views about science, technology and engineering. For this aim and in…

Defense Enrollment Eligibility Reporting System (DEERS) Program Manual

DTIC Science & Technology

1982-05-01

Episcopal Theological Seminary Edinboro State College Pennsylvania of the Southwest Texas Edison Community College Florida Erie Community College Edison...Maritime Academy Maine Lurleen B. Wallace State Junior Maine at Orono, University of Maine College Alabama Maine at Presque Isle , Luther College Iowa...Institute of Technology Pennsylvania Texas Tech University Health Triangle Institute of Technology- Science Center Texas Erie Center Pennsylvania Texas

Telepractice: Creating a Statewide Network of Support in Rural Maine

ERIC Educational Resources Information Center

Hopkins, Karen; Keefe, Barbara; Bruno, Angela

2012-01-01

The Maine Educational Center for the Deaf and Hard of Hearing's (MECDHH's) "POINT" (Providing Opportunities for Integrating New Technologies) project is implementing a telepractice, distance learning collaborative in Maine with eight hub sites and 18 end points using Tandberg videoconferencing technology. This network is planned to be a…

Feasibility of granular bed filtration of an aerosol of ultrafine metallic particles including a pressure drop regeneration system.

PubMed

Bémer, D; Wingert, L; Morele, Y; Subra, I

2015-09-01

A process for filtering an aerosol of ultrafine metallic particles (UFP) has been designed and tested, based on the principle of a multistage granular bed. The filtration system comprised a succession of granular beds of varying thickness composed of glass beads of different diameters. This system allows the pressure drop to be regenerated during filtration ("on-line" mode) using a vibrating probe. Tests monitoring the pressure drop were conducted on a "10-L/min" low airflow rate device and on a "100-m(3)/hr" prototype. Granular bed unclogging is automated on the latter. The cyclic operation and filtration performances are similar to that of filter medium-based industrial dust collectors. Filtration of ultrafine metallic particles generated by different industrial processes such as arc welding, metal cutting, or spraying constitutes a difficult problem due to the high filter clogging properties of these particles and to the high temperatures generally encountered. Granular beds represent an advantageous means of filtering these aerosols with difficult properties.

Antimicrobial and enzymatic activity of anemophilous fungi of a public university in Brazil.

PubMed

Sobral, Laureana V; Melo, Kelly N; Souza, Cleciana M; Silva, Sílvio F; Silva, Gilvania L R; Silva, Andressa L F; Wanderley, Katharine A A; Oliveira, Idjane S; Cruz, Roberta

2017-01-01

To the fungal microbiota the UFPE and biotechnological potential enzymatic and antimicrobial production. Air conditioned environments were sampled using a passive sedimentation technique, the air I ratio and the presence of aflatoxigenic strains evaluated for ANVISA. Icelles were to determine the enzymatic activity of lipase, amylase and protease metabolic liquids to determine antimicrobial activity. Diversity was observed in all CAV environments, CFU/m3 ranged from 14 to 290 and I/E ratio from 0.1 to 1.5. The of the fungal genera were: Aspergillus (50%), Penicillium (21%), Talaromyces (14%), Curvularia and Paecilomyces (7% each). Aspergillus sydowii (Bainier & Sartory) Thom & Church presented enzymatic activity and the Talaromyces purpureogenus Samson, Yilmaz, Houbraken, Spierenb., Seifert, Peterson, Varga & Frisvad presented antibacterial activity against all bacteria that all environments present fungal species biodiversity no toxigenic or pathogenic fungi were found, according to ANVISA legislation for conditioned environments and airborne filamentous fungi present potential for enzymatic and antimicrobial activity.

Contributions of burner, pan, meat and salt to PM emission during grilling.

PubMed

Amouei Torkmahalleh, Mehdi; Ospanova, Saltanat; Baibatyrova, Aknur; Nurbay, Shynggys; Zhanakhmet, Gulaina; Shah, Dhawal

2018-07-01

Grilling ground beef meat was conducted in two locations at Nazarbayev University, Kazakhstan. The experiments were designed such that only particles from beef meat were isolated. A similar experimental protocol was applied at both locations. The average particle number and mass emission rates for grilling pure meat itself (excluding particles from pan and burner) were found to be 9.4 × 10 12 (SD = 7.2 × 10 12 particle min -1 and 7.6 × 10 (SD = 6.3 × 10) mg.min -1 , respectively. The PM emissions (number and mass) from the burner were found to be negligible compared to the pan and meat emissions. Ultrafine particle (UFP) concentrations from the heated pan itself were comparable to those of grilled meat. However, the particle mass concentrations from the pan itself were negligible. Approximately an hour of continuous heating resulted in zero emissions from the pan. Copyright © 2018 Elsevier Inc. All rights reserved.

Dating of fossil human teeth and shells from Toca do Enoque site at Serra das Confusões National Park, Brazil.

PubMed

Kinoshita, Angela; Sullasi, Henry L; Asfora, Viviane K; Azevedo, Renata L; Guzzo, Pedro; Guidon, Niede; Figueiredo, Ana Maria G; Khoury, Helen; Pessis, Anne-Marie; Baffa, Oswaldo

2016-06-07

This work reports the dating of a fossil human tooth and shell found at the archaeological site Toca do Enoque located in Serra das Confusões National Park (Piauí, Brazil). Many prehistoric paintings have been found at this site. An archaeological excavation unearthed three sepulchers with human skeletons and some shells. Two Brazilian laboratories, in Ribeirão Preto (USP) and Recife (UFPE), independently performed Electron Spin Resonance (ESR) measurements to date the tooth and the shell and obtain the equivalent dose received by each sample. The laboratories determined similar ages for the tooth and the shell (~4.8 kyBP). The results agreed with C-14 dating of the shell and other samples (charcoal) collected in the same sepulcher. Therefore, this work provides a valid inter-comparison of results by two independent ESR-dating laboratories and between two dating methods; i.e., C-14 and ESR, showing the validity of ESR dating for this range of ages.

Adopting new medical technologies in Russian hospitals: what causes inefficiency? (qualitative study).

PubMed

Shishkin, Sergey; Zasimova, Liudmila

2018-01-01

The adoption of new medical technologies often generates losses in efficiency associated with the excess or insufficient acquisition of new equipment, an inappropriate choice (in terms of economic and clinical parameters) of medical equipment, and its poor use. Russia is a good example for exploring the problem of the ineffective adoption of new medical technologies due to the massive public investment in new equipment for medical institutions in 2006-2013. This study examines the procurement of new technologies in Russian hospitals to find the main causes of inefficiency. The research strategy was based on in-depth semistructured interviews with representatives of prominent actors (regional health care authorities, hospital executives, senior physicians). The main result is that inefficiencies arise from the contradiction between hospitals' and authorities' motivation for acquiring new technologies: hospitals tend to adopt technologies which bring benefits to their department heads and physicians and minimize maintenance and servicing costs, while the authorities' main concern is the initial cost of the technology.

Phenomenology of summer ozone episodes over the Madrid Metropolitan Area, central Spain

NASA Astrophysics Data System (ADS)

Querol, Xavier; Alastuey, Andrés; Gangoiti, Gotzon; Perez, Noemí; Lee, Hong K.; Eun, Heeram R.; Park, Yonghee; Mantilla, Enrique; Escudero, Miguel; Titos, Gloria; Alonso, Lucio; Temime-Roussel, Brice; Marchand, Nicolas; Moreta, Juan R.; Arantxa Revuelta, M.; Salvador, Pedro; Artíñano, Begoña; García dos Santos, Saúl; Anguas, Mónica; Notario, Alberto; Saiz-Lopez, Alfonso; Harrison, Roy M.; Millán, Millán; Ahn, Kang-Ho

2018-05-01

Various studies have reported that the photochemical nucleation of new ultrafine particles (UFPs) in urban environments within high insolation regions occurs simultaneously with high ground ozone (O3) levels. In this work, we evaluate the atmospheric dynamics leading to summer O3 episodes in the Madrid air basin (central Iberia) by means of measuring a 3-D distribution of concentrations for both pollutants. To this end, we obtained vertical profiles (up to 1200 m above ground level) using tethered balloons and miniaturised instrumentation at a suburban site located to the SW of the Madrid Metropolitan Area (MMA), the Majadahonda site (MJDH), in July 2016. Simultaneously, measurements of an extensive number of air quality and meteorological parameters were carried out at three supersites across the MMA. Furthermore, data from O3 soundings and daily radio soundings were also used to interpret atmospheric dynamics.The results demonstrate the concatenation of venting and accumulation episodes, with relative lows (venting) and peaks (accumulation) in O3 surface levels. Regardless of the episode type, the fumigation of high-altitude O3 (arising from a variety of origins) contributes the major proportion of surface O3 concentrations. Accumulation episodes are characterised by a relatively thinner planetary boundary layer (< 1500 m at midday, lower in altitude than the orographic features), light synoptic winds, and the development of mountain breezes along the slopes of the Guadarrama Mountain Range (located W and NW of the MMA, with a maximum elevation of > 2400 m a.s.l.). This orographic-meteorological setting causes the vertical recirculation of air masses and enrichment of O3 in the lower tropospheric layers. When the highly polluted urban plume from Madrid is affected by these dynamics, the highest Ox (O3+ NO2) concentrations are recorded in the MMA.Vertical O3 profiles during venting episodes, with strong synoptic winds and a deepening of the planetary boundary layer reaching > 2000 m a.s.l., were characterised by an upward gradient in O3 levels, whereas a reverse situation with O3 concentration maxima at lower levels was found during the accumulation episodes due to local and/or regional production. The two contributions to O3 surface levels (fumigation from high-altitude strata, a high O3 background, and/or regional production) require very different approaches for policy actions. In contrast to O3 vertical top-down transfer, UFPs are formed in the planetary boundary layer (PBL) and are transferred upwards progressively with the increase in PBL growth.

The continuous reinvention of diffractive optics

NASA Astrophysics Data System (ADS)

Kress, Bernard C.

2004-02-01

We show in this paper how the field of diffractive optics has moved during these past twenty years from academic research to main stream industry and consumer electronics. We analyze the main driving forces, the various enabling technologies and techniques for both design, fabrication and mass production of diffractive optics, and the successive markets in which this technology has been able to provide economically viable solutions to specific industrials needs. More specifically, we will see how niche applications making use of special features of diffractive optics seem to survive the applications involving the same diffractives, issued from the successive main technology driven investment bubbles.

Tracing Technological Development Trajectories: A Genetic Knowledge Persistence-Based Main Path Approach.

PubMed

Park, Hyunseok; Magee, Christopher L

2017-01-01

The aim of this paper is to propose a new method to identify main paths in a technological domain using patent citations. Previous approaches for using main path analysis have greatly improved our understanding of actual technological trajectories but nonetheless have some limitations. They have high potential to miss some dominant patents from the identified main paths; nonetheless, the high network complexity of their main paths makes qualitative tracing of trajectories problematic. The proposed method searches backward and forward paths from the high-persistence patents which are identified based on a standard genetic knowledge persistence algorithm. We tested the new method by applying it to the desalination and the solar photovoltaic domains and compared the results to output from the same domains using a prior method. The empirical results show that the proposed method can dramatically reduce network complexity without missing any dominantly important patents. The main paths identified by our approach for two test cases are almost 10x less complex than the main paths identified by the existing approach. The proposed approach identifies all dominantly important patents on the main paths, but the main paths identified by the existing approach miss about 20% of dominantly important patents.

Tracing Technological Development Trajectories: A Genetic Knowledge Persistence-Based Main Path Approach

PubMed Central

2017-01-01

The aim of this paper is to propose a new method to identify main paths in a technological domain using patent citations. Previous approaches for using main path analysis have greatly improved our understanding of actual technological trajectories but nonetheless have some limitations. They have high potential to miss some dominant patents from the identified main paths; nonetheless, the high network complexity of their main paths makes qualitative tracing of trajectories problematic. The proposed method searches backward and forward paths from the high-persistence patents which are identified based on a standard genetic knowledge persistence algorithm. We tested the new method by applying it to the desalination and the solar photovoltaic domains and compared the results to output from the same domains using a prior method. The empirical results show that the proposed method can dramatically reduce network complexity without missing any dominantly important patents. The main paths identified by our approach for two test cases are almost 10x less complex than the main paths identified by the existing approach. The proposed approach identifies all dominantly important patents on the main paths, but the main paths identified by the existing approach miss about 20% of dominantly important patents. PMID:28135304

Emerging Communication Technologies (ECT) Phase 2 Report. Volume 1; Main Report

NASA Technical Reports Server (NTRS)

Bastin, Gary L.; Harris, William G.; Chiodini, Robert; Nelson, Richard A.; Huang, PoTien; Kruhm, David A.

2003-01-01

The Emerging Communication Technology (ECT) project investigated three First Mile communication technologies in support of NASA s Second Generation Reusable Launch Vehicle (2nd Gen RLV), Orbital Space Plane, Advanced Range Technology Working Group (ARTWG) and the Advanced Spaceport Technology Working Group (ASTWG). These First Mile technologies have the purpose of interconnecting mobile users with existing Range Communication infrastructures. ECT was a continuation of the Range Information System Management (RISM) task started in 2002. RISM identified the three advance communication technologies investigated under ECT. These were Wireless Ethernet (Wi-Fi), Free Space Optics (FSO), and Ultra Wideband (UWB). Due to the report s size, it has been broken into three volumes: 1) Main Report 2) Appendices 3) UWB.

State of Technology for Renewal of Sewer Force Mains

EPA Science Inventory

This paper presents the results of a review of the state of technology for renewal of force mains (EPA, 2010). The review identified several needs, including the need for rational and common design approaches for rehabilitation systems, quality assurance/quality control procedur...

Analysing Cases in Technology and Design Education: How Could Designing and Making Technological Products Be a Vehicle for Enhancing Understanding of Natural Science Principles?

ERIC Educational Resources Information Center

Hansen, Pal J. Kirkeby

2009-01-01

"Knowledge Promotion" is the recent curriculum for the Norwegian 10-year compulsory school. "Technology and Design" (ToD) is a new main subject area in Natural Science. ToD should be taught across the curriculum between Natural Science, Art and Crafts, and Mathematics. The main goal is that pupils should be able to plan,…

Ultrafine particles, and PM 2.5 generated from cooking in homes

NASA Astrophysics Data System (ADS)

Wan, Man-Pun; Wu, Chi-Li; Sze To, Gin-Nam; Chan, Tsz-Chun; Chao, Christopher Y. H.

2011-11-01

Exposure to airborne particulate matters (PM) emitted during cooking can lead to adverse health effects. An understanding of the exposure to PM during cooking at home provides a foundation for the quantification of possible health risks. The concentrations of airborne particles covering the ultrafine (14.6-100 nm) and accumulation mode (100-661.2 nm) size ranges and PM 2.5 (airborne particulate matters smaller than 2.5 μm in diameter) during and after cooking activities were measured in 12 naturally ventilated, non-smoking homes in Hong Kong, covering a total of 33 cooking episodes. The monitored homes all practiced Chinese-style cooking. Cooking elevated the average number concentrations of ultrafine particles (UFPs) and accumulation mode particles (AMPs) by 10 fold from the background level in the living room and by 20-40 fold in the kitchen. PM 2.5 mass concentrations went up to the maximum average of about 160 μg m -3 in the kitchen and about 60 μg m -3 in the living room. Cooking emitted particles dispersed quickly from the kitchen to the living room indicating that the health impact is not limited to occupants in the kitchen. Particle number and mass concentrations remained elevated for 90 min in the kitchen and for 60 min in the living room after cooking. Particles in cooking emissions were mainly in the ultrafine size range in terms of the number count while AMPs contributed to at least 60% of the surface area concentrations in the kitchen and 73% in the living room. This suggests that AMPs could still be a major health concern since the particle surface area concentration is suggested to have a more direct relationship with inhalation toxicity than with number concentration. Particle number concentration (14.6-661.2 nm) in the living room was about 2.7 times that in the outdoor environment, suggesting that better ventilation could help reduce exposure.

The data and system Nikkei Telecom "Industry/Technology Information Service"

NASA Astrophysics Data System (ADS)

Kurata, Shizuya; Sueyoshi, Yukio

Nihoh Keizai Shimbun started supplying "Industry/Technology Information Service" from July 1989 as a part of Nikkei Telecom Package, which is online information service using personal computers for its terminals. Previously Nikkei's database service mainly covered such areas as economy, corporations and markets. On the other hand, the new "Industry/Technology Information Service" (main data covers industry by industry information-semi macro) is attracting a good deal of attention as it is the first to supply science and technology related database which has not been touched before. Moreover it is attracting attention technically as it has an access by gateway system to JOIS which is the first class science technology file in Japan. This report introduces data and system of "Industry/Technology Information Service" briefly.

Change in the nose areas in children with mouth breathing after nasal cleansing and massage.

PubMed

Melo, Ana Carolina Cardoso de; Gomes, Adriana de Oliveira Camargo; Cunha, Daniele Andrade da; Lima, Sandro Júnior Henrique; Lima, Wigna Rayssa Pereira; Cunha, Renata Andrade da; Silva, Hilton Justino da

2016-01-01

To analyze the changes occurred in the nasal cavity geometry, before and after nasal cleansing, through nasal aeration and acoustic rhinometry in children with oral breathing. Twenty children aged four to 12 years were included in the study. The gathering of participants was conducted at the Multifunctional Laboratory of the Speech Pathology Department of the Federal University of Pernambuco - UFPE. The following procedures were conducted: Identification Index of Signs and Symptoms of Oral Breathing; marking of nasal expiratory airflow using the graded mirror of Altmann, and examination of the Nasal Geometry by Acoustic Rhinometry. The same procedures were performed after nasal massage and cleansing with saline solution. Significant change was observed in the areas with respect to the nasal airflow on both sides after nasal cleansing and massage. As for nasal geometry, measured by acoustic rhinometry, comparison between the nostrils showed that the effect of cleansing and massage was discrete. Nasal aeration measures showed sensitivity to the cleansing and massage technique and measures of nasal geometry confirmed its effect on respiratory physiology.

Educational Technology in China

ERIC Educational Resources Information Center

Meifeng, Liu; Jinjiao, Lv; Cui, Kang

2010-01-01

This paper elaborates the two different academic views of the identity of educational technology in China at the current time--advanced-technology-oriented cognition, known as Electrifying Education, and problem-solving-oriented cognition, known as Educational Technology. It addresses five main modes of educational technology in China: as a…

"Obligatory Technologies": Explaining Why People Feel Compelled to Use Certain Technologies

ERIC Educational Resources Information Center

Chandler, Jennifer A.

2012-01-01

The ideas of technological determinism and the autonomy of technology are long-standing and widespread. This article explores why the use of certain technologies is perceived to be obligatory, thus fueling the fatalism of technological determinism and undermining our sense of freedom vis-a-vis the use of technologies. Three main mechanisms that…

FIELD DEMONSTRATION OF INNOVATIVE LEAK DETECTION/LOCATION TECHNOLOGIES COUPLED WITH WALL-THICKNESS SCREENING FOR WATER MAINS

EPA Science Inventory

The U.S. Environmental Protection Agency sponsored a large-scale field demonstration of innovative leak detection/location and condition assessment technologies on a 76-year old, 2,500-ft long, cement-lined, 24-in. cast iron water main in Louisville, KY from July through Septembe...

Field Demonstration of Innovative Condition Assessment Technologies for Water Mains: Leak Detection and Location

EPA Science Inventory

Three leak detection/location technologies were demonstrated on a 76-year-old, 2,057-ft-long portion of a cement-lined, 24-in. cast iron water main in Louisville, KY. This activity was part of a series of field demonstrations of innovative leak detection/location and condition a...

FIELD DEMONSTRATION OF EMERGING PIPE WALL INTEGRITY ASSESSMENT TECHNOLOGIES FOR LARGE CAST IRON WATER MAINS

EPA Science Inventory

The U.S. Environmental Protection Agency sponsored a large-scale field demonstration of innovative leak detection/location and condition assessment technologies on a 76-year old, 2,500-ft long, cement-lined, 24-in. cast iron water main in Louisville, KY from July through Septembe...

Field Demonstration of Emerging Pipe Wall Integrity Assessment Technologies for Large Cast Iron Water Mains - Paper

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA) sponsored a large-scale field demonstration of innovative leak detection/location and condition assessment technologies on a 76-year old, 2,000-ft long, cement-lined, 24-in. cast-iron water main in Louisville, KY from July through Se...

Heavy hydrocarbon main injector technology

NASA Technical Reports Server (NTRS)

Fisher, S. C.; Arbit, H. A.

1988-01-01

One of the key components of the Advanced Launch System (ALS) is a large liquid rocket, booster engine. To keep the overall vehicle size and cost down, this engine will probably use liquid oxygen (LOX) and a heavy hydrocarbon, such as RP-1, as propellants and operate at relatively high chamber pressures to increase overall performance. A technology program (Heavy Hydrocarbon Main Injector Technology) is being studied. The main objective of this effort is to develop a logic plan and supporting experimental data base to reduce the risk of developing a large scale (approximately 750,000 lb thrust), high performance main injector system. The overall approach and program plan, from initial analyses to large scale, two dimensional combustor design and test, and the current status of the program are discussed. Progress includes performance and stability analyses, cold flow tests of injector model, design and fabrication of subscale injectors and calorimeter combustors for performance, heat transfer, and dynamic stability tests, and preparation of hot fire test plans. Related, current, high pressure, LOX/RP-1 injector technology efforts are also briefly discussed.

Analysis of the lack of scientific and technological talents of high-level women in China

NASA Astrophysics Data System (ADS)

Lin, Wang

2017-08-01

The growth and development of high-level female scientific and technological talents has become a global problem, facing severe challenges. The lack of high-level women in science and technology has become a global problem. How to recruit and help female scientists and technological talents grow raises awareness from the industry. To find out the main reasons for the lack of high-level female scientific and technological talent. This paper analyses the impact of gender discrimination on the lack of high-level female scientific and technological talents, the impact of disciplinary differences on female roles. The main reasons are: women’s natural disadvantage of mathematical thinking; female birth, the traditional culture on the role of women and the impact of values.

A Review of Optical NDT Technologies

PubMed Central

Zhu, Yong-Kai; Tian, Gui-Yun; Lu, Rong-Sheng; Zhang, Hong

2011-01-01

Optical non-destructive testing (NDT) has gained more and more attention in recent years, mainly because of its non-destructive imaging characteristics with high precision and sensitivity. This paper provides a review of the main optical NDT technologies, including fibre optics, electronic speckle, infrared thermography, endoscopic and terahertz technology. Among them, fibre optics features easy integration and embedding, electronic speckle focuses on whole-field high precision detection, infrared thermography has unique advantages for tests of combined materials, endoscopic technology provides images of the internal surface of the object directly, and terahertz technology opens a new direction of internal NDT because of its excellent penetration capability to most of non-metallic materials. Typical engineering applications of these technologies are illustrated, with a brief introduction of the history and discussion of recent progress. PMID:22164045

The Technological Dimension of Educational Technology in Europe

ERIC Educational Resources Information Center

Dimitriadis, Yannis

2012-01-01

This article describes some of the main technological trends and issues of the European landscape of research and innovation in educational technology. Although several innovative technologies (tools, architectures, platforms, or approaches) emerge, such as intelligent support to personalization, collaboration or adaptation in mobile, game-based,…

Offshore Wind Resource, Cost, and Economic Potential in the State of Maine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musial, Walter D.

This report provides information for decision-makers about floating offshore wind technologies in the state of Maine. It summarizes research efforts performed at the National Renewable Energy Laboratory between 2015 and 2017 to analyze the resource potential, cost of offshore wind, and economic potential of offshore wind from four primary reports: Musial et al. (2016); Beiter et al. (2016, 2017); and Mone et al. (unpublished). From Musial et al. (2016), Maine's technical offshore wind resource potential ranked seventh in the nation overall with more than 411 terawatt-hours/year of offshore resource generating potential. Although 90% of this wind resource is greater thanmore » 9.0-meters-per-second average velocity, most of the resource is over deep water, where floating wind technology is needed. Levelized cost of energy and levelized avoided cost of energy were computed to estimate the unsubsidized 'economic potential' for Maine in the year 2027 (Beiter et al. 2016, 2017). The studies found that Maine may have 65 gigawatts of economic potential by 2027, the highest of any U.S. state. Bottom-line costs for the Aqua Ventus project, which is part of the U.S. Department of Energy's Advanced Technology Demonstration project, were released from a proprietary report written by NREL in 2016 for the University of Maine (Mone et al. unpublished). The report findings were that economies of scale and new technology advancements lowered the cost from $300/megawatt-hour (MWh) for the two-turbine 12-megawatt (MW) Aqua Ventus 1 project, to $126/MWh for the commercial-scale, 498-MW Aqua Ventus-2 project. Further cost reductions to $77/MWh were found when new technology advancements were applied for the 1,000-MW Aqua Ventus-3 project in 2030. No new analysis was conducted for this report.« less

Technological Knowledge and Reasoning in Finnish and Estonian Technology Education

ERIC Educational Resources Information Center

Autio, Ossi; Soobik, Mart

2017-01-01

The main idea of this research was to find out if there is a relationship between students' undertakings within Craft and Technology education and their ability to understand technological concepts. Study participants' technological knowledge and reasoning was measured with a questionnaire regarding mechanical systems connected with simple…

The Main Features of Undertaking Technological and Vocational Curriculum Reform in Taiwan

ERIC Educational Resources Information Center

Lee, Lung-Sheng Steven; Huang, Bo-Shiang Bert

2003-01-01

In Taiwan, technological and vocational education (TVE) is primarily offered in vocational high schools (VHS's), career programs in comprehensive high schools (CHSs), junior colleges of technology (JCTs), colleges of technology (CTs), and universities of technology (UTs), which prepare practical technical and managerial personnel for industry and…

Culvert rehabilitation & invert lining using fiber reinforced polymer (FRP) composites.

DOT National Transportation Integrated Search

2010-06-01

As part of the state of Maine bridge funding initiative, MaineDOT has partnered with the University of : Maines AEWC Advanced Structures and Composite Center and the Maine composites industry to : incorporate composite technologies into bridge con...

Use of communication technologies in document exchange for the management of construction projects

NASA Astrophysics Data System (ADS)

Mesároš, Peter; Mandičák, Tomáš

2016-06-01

Information and communication technologies represent a set of people, processes, technical and software tools providing collection, transport, storage and processing of data for distribution and presentation of information. Particularly communication systems are the main tool for information exchange. Of the other part, these technologies have a broad focus and use. One of them is the exchange of documents in the management of construction projects. Paper discusses the issue of exploitation level of communication technologies in construction project management. The main objective of this paper is to analyze exploitation level of communication technologies. Another aim of the paper is to compare exploitation level or rate of document exchange by electronic communication devices and face-to-face communication.

Direction of rational use of water at livestock facilities

NASA Astrophysics Data System (ADS)

Potseluev, A. A.; Nazarov, I. V.

2017-05-01

The article notes the world water shortage problem. Against this background, Russia’s agricultural production is considered, in particular the livestock sector as the main consumer of water resources. The structure of the main technological processes at livestock facilities is given and possible technological damage is indicated in case of the lack of technological processes for servicing animals and poultry with water. The direction of rational use of water based on the introduction of new technical and technological solutions of water supply systems and means is substantiated. Constructive solutions of systems and facilities that help to reduce water consumption are presented, and as well a possible positive effect.

Application of BIM Technology in Prefabricated Buildings

NASA Astrophysics Data System (ADS)

Zhanglin, Guo; Si, Gao; Jun-e, Liu

2017-08-01

The development of fabricated buildings has become the main trend of the developm ent of modern construction industry in China. As the main tool of building information, BIM (b uilding information modeling) has greatly promoted the development of construction industry. Based on the review of the papers about the fabricated buildings and BIM technology in recent years, this paper analyzes the advantages of fabricated buildings and BIM technology, then exp lores the application of BIM technology in fabricated buildings. It aims to realize the rationaliz ation and scientification of project lifecycle management in fabricated construction project, and finally form a coherent information platform in the fabricated building.

The infrared imaging radiometer for PICASSO-CENA

NASA Astrophysics Data System (ADS)

Corlay, Gilles; Arnolfo, Marie-Christine; Bret-Dibat, Thierry; Lifferman, Anne; Pelon, Jacques

2017-11-01

Microbolometers are infrared detectors of an emerging technology mainly developed in US and few other countries for few years. The main targets of these developments are low performing and low cost military and civilian applications like survey cameras. Applications in space are now arising thanks to the design simplification and the associated cost reduction allowed by this new technology. Among the four instruments of the payload of PICASSO-CENA, the Imaging Infrared Radiometer (IIR) is based on the microbolometer technology. An infrared camera in development for the IASI instrument is the core of the IIR. The aim of the paper is to recall the PICASSO-CENA mission goal, to describe the IIR instrument architecture and highlight its main features and performances and to give the its development status.

Flow experience among information and communication technology users.

PubMed

Rodríguez-Sánchez, Alma M; Schaufeli, Wilmar B; Salanova, Marisa; Cifre, Eva

2008-02-01

The use of technologies is more common in daily life; working with technologies might be associated with positive experiences such as flow. However, there is little empirical research on flow experiences in technology settings. The main aim of this study was to confirm the three-dimensional construct of flow, i.e., absorption, enjoyment, and intrinsic interest, among 517 Information and Communication Technology users [234 students whose mean age was 23 yr. (SD = 3.8)] from different areas of study, mainly Law, Public Administration, Chemistry, and Psychology, and 283 employees [whose mean age was 33 yr. (SD = 7.8)] of 21 different companies from various sectors of production, namely, public administration, industrial production, and services. Analysis showed, as expected, flow is a three-dimensional psychological construct and invariant among samples of technology users. Practical and theoretical implications as well as further research are discussed.

Selection criteria for wastewater treatment technologies to protect drinking water.

PubMed

von Sperling, M

2000-01-01

The protection of water bodies used as sources for drinking water is intimately linked to the adoption of adequate technologies for the treatment of the wastewater generated in the catchment area. The paper presents a general overview of the main technologies used for the treatment of domestic sewage, with a special emphasis on developing countries, and focussing on the main parameters of interest, such as BOD, coliforms and nutrients. A series of tables, figures and charts that can be used for the preliminary selection of treatment technologies is presented. The systems analysed are: stabilisation ponds, activated sludge, trickling filters, anaerobic systems and land disposal. Within each system, the main process variants are covered. Two summary tables are presented, one for quantitative analysis, including easily usable information based on per capita values (US$/cap, Watts/cap, m2 area/cap, m3 sludge/cap), and another for a qualitative comparison among the technologies, based on a one-to-five-star scoring system. The recent trend in tropical countries in the use of UASB (Upflow Anaerobic Sludge Blanket) reactors is also discussed.

Impact of Technological and Structural Change on Employment: Prospective Analysis 2020. Background Report.

ERIC Educational Resources Information Center

Christidis, Panayotis, Ed.; Hernandez, Hector, Ed.; Lievonen, Jorma, Ed.

A study examined the role of technology in the European Union's (EU's) economy and its impacts on employment. Starting point was Technology and Employment Maps of the FUTURES project that identified main emerging technological developments (TDs) and their implications for employment. Technologies' potential impact on productivity growth and…

Evolution of Emergent Technologies for Producing Nonwoven Fabrics for Air Filtration

ERIC Educational Resources Information Center

Ou, Yingjie

2016-01-01

Nonwovens is a fast growing industry driven by technological research and development (R&D), and one of the major application areas for nonwovens is air filtration. Research on nonwovens technologies has mainly focused on the science and technology areas, but there is very little published research on technology management issues within the…

Structures, Material and Processes Technology in the Future Launchers Preparatory Program

NASA Astrophysics Data System (ADS)

Baiocco, P.; Ramusat, G.; Breteau, J.; Bouilly, Th.; Lavelle, Fl.; Cardone, T.; Fischer, H.; Appel, S.; Block, U.

2014-06-01

In the frame of the technology / demonstration activity for European launchers developments and evolutions, a top-down / bottom-up approach has been employed to identify promising technologies and alternative conception. The top-down approach consists in looking for system-driven design solutions and the bottom-up approach features design solutions leading to substantial advantages for the system. The main investigations have been devoted to structures, material and process technology.Preliminary specifications have been used in order to permit sub-system design with the goal to find the major benefit for the overall launch system. In this respect competitiveness factors have been defined to down- select the technology and the corresponding optimized design. The development cost, non-recurring cost, industrialization and operational aspects have been considered for the identification of the most interesting solutions. The TRL/IRL has been assessed depending on the manufacturing company and a preliminary development plan has been issued for some technology.The reference launch systems for the technology and demonstration programs are mainly Ariane 6 with its evolutions, VEGA C/E and others possible longer term systems. Requirements and reference structures architectures have been considered in order to state requirements for representative subscale or full scale demonstrators. The major sub-systems and structures analyzed are for instance the upper stage structures, the engine thrust frame (ETF), the inter stage structures (ISS), the cryogenic propellant tanks, the feeding lines and their attachments, the pressurization systems, the payload adapters and fairings. A specific analysis has been devoted to the efficiency of production processes associated to technologies and design features.The paper provides an overview of the main results of the technology and demonstration activities with the associated system benefits. The materials used for the main structures are metallic and composite owing to sub-systems or sub-assemblies proposed for the European launch systems in development and their evolutions.

Digital Technologies as Education Innovation at Universities

ERIC Educational Resources Information Center

Kryukov, Vladimir; Gorin, Alexey

2017-01-01

This paper analyses the use of digital technology-based education innovations in higher education. It demonstrated that extensive implementation of digital technologies in universities is the main factor conditioning the acceleration of innovative changes in educational processes, while digital technologies themselves become one of the key…

Nanotechnology and chip level systems for pressure driven liquid chromatography and emerging analytical separation techniques: a review.

PubMed

Lavrik, N V; Taylor, L T; Sepaniak, M J

2011-05-23

Pressure driven liquid chromatography (LC) is a powerful and versatile separation technique particularly suitable for differentiating species present in extremely small quantities. This paper briefly reviews main historical trends and focuses on more recently developed technological approaches in miniaturization and on-chip integration of LC columns. The review emphasizes enabling technologies as well as main technological challenges specific to pressure driven separations and highlights emerging concepts that could ultimately overcome fundamental limitations of conventional LC columns. Copyright © 2011 Elsevier B.V. All rights reserved.

The Main Factors of the Attitudes of Greek Kindergarten Teachers towards Information and Communication Technology

ERIC Educational Resources Information Center

Zaranis, Nicholas; Oikonomidis, Vassilios

2016-01-01

The purpose of this article is to examine the main factors of Greek kindergarten teachers' attitudes towards information and communication technology (ICT) in kindergarten. This two-phase survey was carried out in 2007 and 2012 and used 383 and 295 participants respectively. The participants in both groups were drawn from kindergarten teachers in…

Of Levers and Electrons and Learning and Enlightenment: Technological Augmentation of Cognition in the United States Since 1776.

ERIC Educational Resources Information Center

Merzbach, Uta C.

An extensive historical background for an exhibition dealing with the technological augmentation of human intellect is presented. The main theme underlying the discussion is the changing concept of cognition in the last 200 years. Five main views of the learning process are traced as they developed in philosophy and in practical application: the…

Mass Communication: Technology Use and Instruction. ERIC Digest.

ERIC Educational Resources Information Center

Brynildssen, Shawna

This Digest reviews the literature on recent attempts to incorporate technology into the instruction of journalism and mass communication. It first discusses the four main categories of current technology use in journalism and mass communication: classroom instruction; online syllabi/materials; distance learning; and technological literacy. It…

Nanocrystals Technology for Pharmaceutical Science.

PubMed

Cheng, Zhongyao; Lian, Yumei; Kamal, Zul; Ma, Xin; Chen, Jianjun; Zhou, Xinbo; Su, Jing; Qiu, Mingfeng

2018-05-17

Nanocrystals technology is a promising method for improving the dissolution rate and enhancing the bioavailability of poorly soluble drugs. In recent years, it has been developing rapidly and applied to drug research and engineering. Nanocrystal drugs can be formulated into various dosage forms. This review mainly focused on the nanocrystals technology and its application in pharmaceutical science. Firstly, different preparation methods of nanocrystal technology and the characterization of nanocrystal drugs are briefly described. Secondly, the application of nanocrystals technology in pharmaceutical science is mainly discussed followed by the introduction of sustained release formulations. Then, the scaling up process, marketed nanocrystal drug products and regulatory aspects about nanodrugs are summarized. Finally, the specific challenges and opportunities of nanocrystals technology for pharmaceutical science are summarized and discussed. This review will provide a comprehensive guide for scientists and engineers in the field of pharmaceutical science and biochemical engineering. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Advancing Teacher Technology Education Using Open-Ended Learning Environments as Research and Training Platforms

ERIC Educational Resources Information Center

Poitras, Eric; Doleck, Tenzin; Huang, Lingyun; Li, Shan; Lajoie, Susanne

2017-01-01

A primary concern of teacher technology education is for pre-service teachers to develop a sophisticated mental model of the affordances of technology that facilitates both teaching and learning with technology. One of the main obstacles to developing the requisite technological pedagogical content knowledge is the inherent challenge faced by…

Assistive technology applied to education of students with visual impairment.

PubMed

Alves, Cássia Cristiane de Freitas; Monteiro, Gelse Beatriz Martins; Rabello, Suzana; Gasparetto, Maria Elisabete Rodrigues Freire; de Carvalho, Keila Monteiro

2009-08-01

Verify the application of assistive technology, especially information technology in the education of blind and low-vision students from the perceptions of their teachers. Descriptive survey study in public schools in three municipalities of the state of São Paulo, Brazil. The sample comprised 134 teachers. According to the teachers' opinions, there are differences in the specificities and applicability of assistive technology for blind and low-vision students, for whom specific computer programs are important. Information technology enhances reading and writing skills, as well as communication with the world on an equal basis, thereby improving quality of life and facilitating the learning process. The main reason for not using information technology is the lack of planning courses. The main requirements for the use of information technology in schools are enough computers for all students, advisers to help teachers, and pedagogical support. Assistive technology is applied to education of students with visual impairment; however, teachers indicate the need for infrastructure and pedagogical support. Information technology is an important tool in the inclusion process and can promote independence and autonomy of students with visual impairment.

Development of Key Performance Indicators for the Engineering Technology Education Programs in Taiwan

ERIC Educational Resources Information Center

Lee, Lung-Sheng; Lai, Chun-Chin

2004-01-01

In comparison with engineering, engineering technology is more practical and purposeful. The engineering technology education programs in Taiwan have been mainly offered in 56 universities/colleges of technology (UTs/CTs) and are anticipated to continuously improve their performance to prepare quality engineering technologists. However, it is…

Technology Education in Maine. Curriculum Guide.

ERIC Educational Resources Information Center

Maine State Dept. of Educational and Cultural Services, Augusta. Bureau of Vocational Education.

This curriculum guide presents basic definitions, models, and examples as a framework that individual technology education instructors or departments can use to construct their own units, courses, and curricula at any level. An overview describes the development of the model and the content of technology education. Section I explains technology.…

Test Results of the Modified Space Shuttle Main Engine at the Marshall Space Flight Center Technology Test Bed Facility

NASA Technical Reports Server (NTRS)

Cook, J.; Dumbacher, D.; Ise, M.; Singer, C.

1990-01-01

A modified space shuttle main engine (SSME), which primarily includes an enlarged throat main combustion chamber with the acoustic cavities removed and a main injector with the stability control baffles removed, was tested. This one-of-a-kind engine's design changes are being evaluated for potential incorporation in the shuttle flight program in the mid-1990's. Engine testing was initiated on September 15, 1988 and has accumulated 1,915 seconds and 19 starts. Testing is being conducted to characterize the engine system performance, combustion stability with the baffle-less injector, and both low pressure oxidizer turbopump (LPOTP) and high pressure oxidizer turbopump (HPOTP) for suction performance. These test results are summarized and compared with the SSME flight configuration data base. Testing of this new generation SSME is the first product from the technology test bed (TTB). Figure test plans for the TTB include the highly instrumented flight configuration SSME and advanced liquid propulsion technology items.

Using Technology in the Classroom

ERIC Educational Resources Information Center

Boles, Stephanie Reeve

2011-01-01

The author describes how she has come to use technology in her classroom over the years. Her main topics include using the internet, experiencing podcasts, using technology for assessment, and recording results from science research. (Contains 3 online resources and 5 figures.)

Smart infrared inspection system field operational test : [technology brief].

DOT National Transportation Integrated Search

2014-04-01

One of the main goals of the Commercial Vehicle : Roadside Technology Corridor (CMVRTC) is to : support and evaluate the use of innovative : technologies that improve commercial truck and bus : safety. The Smart Infrared Inspection System : (SIRIS) w...

Key issues and technical route of cyber physical distribution system

NASA Astrophysics Data System (ADS)

Zheng, P. X.; Chen, B.; Zheng, L. J.; Zhang, G. L.; Fan, Y. L.; Pei, T.

2017-01-01

Relying on the National High Technology Research and Development Program, this paper introduced the key issues in Cyber Physical Distribution System (CPDS), mainly includes: composite modelling method and interaction mechanism, system planning method, security defence technology, distributed control theory. Then on this basis, the corresponding technical route is proposed, and a more detailed research framework along with main schemes to be adopted is also presented.

FIELD DEMONSTRATION OF INNOVATIVE CONDITION ASSESSMENT TECHNOLOGIES FOR WATER MAINS: ACOUSTIC PIPE WALL ASSESSMENT, INTERNAL INSPECTION, AND EXTERNAL INSPECTIONVOLUME 1: TECHNICAL REPORT AND VOLUME 2: APPENDICES

EPA Science Inventory

Nine pipe wall integrity assessment technologies were demonstrated on a 76-year-old, 2,057-ft-long portion of a cement-lined, 24-in. cast iron water main in Louisville, KY. This activity was part of a series of field demonstrations of innovative leak detection/location and condi...

Representations of Technology in the "Technical Stories" for Children of Otto Witt, Early 20th Century Swedish Technology Educator

ERIC Educational Resources Information Center

Axell, Cecilia; Hallström, Jonas

2013-01-01

Children's fiction in school libraries have played and still play a role in mediating representations of technology and attitudes towards technology to schoolchildren. In early 20th century Sweden, elementary education, including textbooks and literature that were used in teaching, accounted for the main mediation of technological knowledge to…

Spin-transfer torque magnetoresistive random-access memory technologies for normally off computing (invited)

NASA Astrophysics Data System (ADS)

Ando, K.; Fujita, S.; Ito, J.; Yuasa, S.; Suzuki, Y.; Nakatani, Y.; Miyazaki, T.; Yoda, H.

2014-05-01

Most parts of present computer systems are made of volatile devices, and the power to supply them to avoid information loss causes huge energy losses. We can eliminate this meaningless energy loss by utilizing the non-volatile function of advanced spin-transfer torque magnetoresistive random-access memory (STT-MRAM) technology and create a new type of computer, i.e., normally off computers. Critical tasks to achieve normally off computers are implementations of STT-MRAM technologies in the main memory and low-level cache memories. STT-MRAM technology for applications to the main memory has been successfully developed by using perpendicular STT-MRAMs, and faster STT-MRAM technologies for applications to the cache memory are now being developed. The present status of STT-MRAMs and challenges that remain for normally off computers are discussed.

Views and considerations on ICT-AT competences development within the ENTELIS project: The Case of Cyprus.

PubMed

Mavrou, Katerina; Meletiou-Mavrotheris, Maria

2015-01-01

This submission presents part of the EU funded project ENTELIS (European Network for Technology Enhanced Learning in an Inclusive Society), which aims to address issues of digital divide and digital equity for people with disabilities of all ages, and to increase participation and social inclusion. This paper presents the main activities and outcomes of the research work package of the project (WP3), from one of the partner countries, Cyprus. The aim of the conducted research was to identify the conceptions and beliefs of end-users, trainers, and service/technology providers and professionals, on the multifaceted relation between ICT/ICT-AT (Information Communication Technology - Assistive Technology) and learning of technology. Data collection involved the development and administration of three semi-structured interview protocols, one for each group of participants, in five different European countries. Results have been compiled to develop a State-of-Art Report on ICT and ICT-AT education and learning, highlighting the main trends, as well the main present barriers, emergent and future needs in terms of analysis, acquisition and reinforcing of digital competences bridging the worlds of education and work.

Chlor-Alkali Technology.

ERIC Educational Resources Information Center

Venkatesh, S.; Tilak, B. V.

1983-01-01

Chlor-alkali technology is one of the largest electrochemical industries in the world, the main products being chlorine and caustic soda (sodium hydroxide) generated simultaneously by the electrolysis of sodium chloride. This technology is reviewed in terms of electrochemical principles and manufacturing processes involved. (Author/JN)

Primary EFL Teachers' Technology Use in China: Patterns and Perceptions

ERIC Educational Resources Information Center

Li, Guofang; Ni, Xiaopeng

2011-01-01

Drawing on survey data, this paper examines the patterns and perceptions of technology use by primary EFL teachers in China. Findings suggest that although Chinese EFL teachers hold positive attitudes toward the value of technology for teaching and learning, they use technology mainly for teacher-centered purposes, such as teaching preparation and…

Advanced High Pressure O2/H2 Technology

NASA Technical Reports Server (NTRS)

Morea, S. F. (Editor); Wu, S. T. (Editor)

1985-01-01

Activities in the development of advanced high pressure oxygen-hydrogen stage combustion rocket engines are reported. Particular emphasis is given to the Space Shuttle main engine. The areas of engine technology discussed include fracture and fatigue in engine components, manufacturing and producibility engineering, materials, bearing technology, structure dynamics, fluid dynamics, and instrumentation technology.

Using Educational Technology in Applications as Element of Teaching for Special Disciplines

ERIC Educational Resources Information Center

Neupokoeva, Elena E.; Chapaev, Nikolay K.; Akimova, Olga B.; Shcherbin, Matthew D.; Borovikov, Evgenij A.

2016-01-01

The relevance of research problem due to high growth of information technologies roles in industrial activity and low level of teachers professionalism in topics related with information technology. Purpose of article is to show main components of a learning technology aimed at improving level teachers skills to solve didactic problems associated…

Messier: A Detailed NVM-Based DIMM Model for the SST Simulation Framework.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Awad, Amro; Voskuilen, Gwendolyn Renae; Rodrigues, Arun F.

2017-02-01

DRAM technology is the main building block of main memory, however, DRAM scaling is becoming very challenging. The main issues for DRAM scaling are the increasing error rates with each new generation, the geometric and physical constraints of scaling the capacitor part of the DRAM cells, and the high power consumption caused by the continuous need for refreshing cell values. At the same time, emerging Non- Volatile Memory (NVM) technologies, such as Phase-Change Memory (PCM), are emerging as promising replacements for DRAM. NVMs, when compared to current technologies e.g., NAND-based ash, have latencies comparable to DRAM. Additionally, NVMs are non-volatile,more » which eliminates the need for refresh power and enables persistent memory applications. Finally, NVMs have promising densities and the potential for multi-level cell (MLC) storage.« less

[Advances in the research of application of collagen in three-dimensional bioprinting].

PubMed

Li, H H; Luo, P F; Sheng, J J; Liu, G C; Zhu, S H

2016-10-20

As a new industrial technology with characteristics of high precision and accuracy, the application of three-dimensional bioprinting technology is increasingly wide in the field of medical research. Collagen is one of the most common ingredients in tissue, and it has good biological material properties. There are many reports of using collagen as main composition of " ink" of three-dimensional bioprinting technology. However, the applied collagen is mainly from heterogeneous sources, which may cause some problems in application. Recombinant human source collagen can be obtained from microorganism fermentation by transgenic technology, but more research should be done to confirm its property. This article reviews the advances in the research of collagen and its biological application in three-dimensional bioprinting.

Varied dose exposures to ultrafine particles in the motorcycle smoke cause kidney cell damages in male mice.

PubMed

Wardoyo, Arinto Y P; Juswono, Unggul P; Noor, Johan A E

2018-01-01

Ultrafine particles (UFPs) are one of motorcycle exhaust emissions which can penetrate the lung alveoli and deposit in the kidney. This study was aimed to investigate mice kidney cell physical damage (deformation) due to motorcycle exhaust emission exposures. The motorcycle exhaust emissions were sucked from the muffler with the rate of 33 cm 3 /s and passed through an ultrafine particle filter system before introduced into the mice exposure chamber. The dose concentration of the exhaust emissions was varied by setting the injected time of the 20s, 40s, 60s, 80s, and 100s. The mice were exposed to the smoke in the chamber for 100 s twice a day. The impact of the ultrafine particles on the kidney was observed by identifying the histological image of the kidney cell deformation using a microscope. The exposure was conducted for 10 days. The kidney observations were carried out on day 11. The results showed that there was a significant linear correlation between the total concentration of ultrafine particles deposited in the kidneys and the physical damage percentages. The increased concentrations of ultrafine particles caused larger cell deformation to the kidneys.

A mechanism for the production of ultrafine particles from concrete fracture.

PubMed

Jabbour, Nassib; Rohan Jayaratne, E; Johnson, Graham R; Alroe, Joel; Uhde, Erik; Salthammer, Tunga; Cravigan, Luke; Faghihi, Ehsan Majd; Kumar, Prashant; Morawska, Lidia

2017-03-01

While the crushing of concrete gives rise to large quantities of coarse dust, it is not widely recognized that this process also emits significant quantities of ultrafine particles. These particles impact not just the environments within construction activities but those in entire urban areas. The origin of these ultrafine particles is uncertain, as existing theories do not support their production by mechanical processes. We propose a hypothesis for this observation based on the volatilisation of materials at the concrete fracture interface. The results from this study confirm that mechanical methods can produce ultrafine particles (UFP) from concrete, and that the particles are volatile. The ultrafine mode was only observed during concrete fracture, producing particle size distributions with average count median diameters of 27, 39 and 49 nm for the three tested concrete samples. Further volatility measurements found that the particles were highly volatile, showing between 60 and 95% reduction in the volume fraction remaining by 125 °C. An analysis of the volatile fraction remaining found that different volatile material is responsible for the production of particles between the samples. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biomarker as a Research Tool in Linking Exposure to Air Particles and Respiratory Health

PubMed Central

2015-01-01

Some of the environmental toxicants from air pollution include particulate matter (PM10), fine particulate matter (PM2.5), and ultrafine particles (UFP). Both short- and long-term exposure could result in various degrees of respiratory health outcomes among exposed persons, which rely on the individuals' health status. Methods. In this paper, we highlight a review of the studies that have used biomarkers to understand the association between air particles exposure and the development of respiratory problems resulting from the damage in the respiratory system. Data from previous epidemiological studies relevant to the application of biomarkers in respiratory system damage reported from exposure to air particles are also summarized. Results. Based on these analyses, the findings agree with the hypothesis that biomarkers are relevant in linking harmful air particles concentrations to increased respiratory health effects. Biomarkers are used in epidemiological studies to provide an understanding of the mechanisms that follow airborne particles exposure in the airway. However, application of biomarkers in epidemiological studies of health effects caused by air particles in both environmental and occupational health is inchoate. Conclusion. Biomarkers unravel the complexity of the connection between exposure to air particles and respiratory health. PMID:25984536

Using satellite-based measurements to explore ...

EPA Pesticide Factsheets

New particle formation (NPF) can potentially alter regional climate by increasing aerosol particle (hereafter particle) number concentrations and ultimately cloud condensation nuclei. The large scales on which NPF is manifest indicate potential to use satellite-based (inherently spatially averaged) measurements of atmospheric conditions to diagnose the occurrence of NPF and NPF characteristics. We demonstrate the potential for using satellite-measurements of insolation (UV), trace gas concentrations (sulfur dioxide (SO2), nitrogen dioxide (NO2), ammonia (NH3), formaldehyde (HCHO), ozone (O3)), aerosol optical properties (aerosol optical depth (AOD), Ångström exponent (AE)), and a proxy of biogenic volatile organic compound emissions (leaf area index (LAI), temperature (T)) as predictors for NPF characteristics: formation rates, growth rates, survival probabilities, and ultrafine particle (UFP) concentrations at five locations across North America. NPF at all sites is most frequent in spring, exhibits a one-day autocorrelation, and is associated with low condensational sink (AOD×AE) and HCHO concentrations, and high UV. However, there are important site-to-site variations in NPF frequency and characteristics, and in which of the predictor variables (particularly gas concentrations) significantly contribute to the explanatory power of regression models built to predict those characteristics. This finding may provide a partial explanation for the reported spatia

[Validation of National College Health Risk Behavior Survey to be use with Brazilian college students].

PubMed

Franca, Carolina da; Colares, Viviane

2010-06-01

The objective of this article is to translate, to adapt and to validate the National College Health Risk Behavior Survey to apply at Brazilian college students. 208 college students from the Federal University of Pernambuco (UFPE) and University of Pernambuco (UPE) participated in the study. The validation was carried through in five stages: (1) translation; (2) retrotranslation; (3) correction and semantic adaptation (cultural adaptation); (4) face validation; (5) test-retest. Adaptations were done to deal with any semantic disagreements found between translation and retrotranslation. After face validation, the questionnaire was reduced from 96 to 52 questions. From the 11 items analyzed, the majority presented good and perfect Kappa: security and violence (Kappa=0.89); suicide (Kappa=1.00); use of the tobacco (Kappa=0.90); drinking consumption (Kappa=0.78); cocaine and other drugs consumption (Kappa=0.70); sexual behavior (Kappa=0,88) and corporal weight (Kappa=0.89). Only the item about feeding presented weak Inter-examiner Kappa (Kappa = 0.26) and the topic on health information presented moderate Kappa (Kappa=0.56). The average Kappa for all items was good (0.76). The instrument may be considered validated in the Portuguese language in Brazil with acceptable reproducibility.

Beliefs about Teaching and Uses of Technology among Pre-Service Teachers

ERIC Educational Resources Information Center

Teo, Timothy; Chai, Ching Sing; Hung, David; Lee, Chwee Beng

2008-01-01

In the current learning environments, technology is integrated in different ways. Teachers acting in the capacity of main change agents bring with them beliefs about teaching which effects their use of technology in the classroom. This study aims to examine the possible relationship between teachers' beliefs about teaching and uses of technology.…

Technology, Demographic Characteristics and E-Learning Acceptance: A Conceptual Model Based on Extended Technology Acceptance Model

ERIC Educational Resources Information Center

Tarhini, Ali; Elyas, Tariq; Akour, Mohammad Ali; Al-Salti, Zahran

2016-01-01

The main aim of this paper is to develop an amalgamated conceptual model of technology acceptance that explains how individual, social, cultural and organizational factors affect the students' acceptance and usage behaviour of the Web-based learning systems. More specifically, the proposed model extends the Technology Acceptance Model (TAM) to…

Comprehensive evaluation of the main technology for new sewage treatment plants in small towns along the Duliujian river basin

NASA Astrophysics Data System (ADS)

Chen, Yiming; Zhou, Beihai; Yuan, Rongfang; Bao, Xiangming; Li, Dongwei

2018-02-01

In recent years, water contamination problem has been becoming more and more serious due to increasing wastewater discharge. So our country has accelerated the pace of constructing sewage treatment plant in small towns. But in China it has not been issued any corresponding technical specifications about the choice of treatment technology. So the article is based on the basin of Duliujian river, through field research, data collection and analysis of relevant documentations, preliminarily elects seven kinds of technology: Improved A2/O, Integrated oxidation ditch, Orbal oxidation ditch, CASS, A/O+refined diatomite, BIOLAK and UNITANK as alternatives for Tianjin sewage discharge local standard.Then the article use the analytic hierarchy process (AHP) to evaluate the seven kinds of alternatives, finally it is concluded that CASS technology is most suitable for the main technology of new sewage treatment plants in small towns along the Duliujian River basin.

The Potential of RFID Technology in the Textile and Clothing Industry: Opportunities, Requirements and Challenges

NASA Astrophysics Data System (ADS)

Legnani, Elena; Cavalieri, Sergio; Pinto, Roberto; Dotti, Stefano

In the current competitive environment, companies need to extensively exploit the use of advanced technologies in order to develop a sustainable advantage, enhance their operational efficiency and better serve customers. In this context, RFID technology has emerged as a valid support for the company progress and its value is becoming more and more apparent. In particular, the textile and clothing industry, characterised by short life-cycles , quick response production , fast distribution, erratic customer preferences and impulsive purchasing, is one of the sectors which can extensively benefit from the RFID technology. However, actual applications are still very limited, especially in the upstream side of the supply network. This chapter provides an insight into the main benefits and potentials of this technology and highlights the main issues which are currently inhibiting its large scale development in the textile and clothing industry. The experience of two industry-academia projects and the relative fallouts are reported.

Scientific and Technological Progress and Job Qualification.

ERIC Educational Resources Information Center

Ivanov, N. P.

Clarifying the influences determining how and to what extent highly qualified personnel are employed, this study discusses those sorts of economic and technological advances affecting employment potentials. Two main trends in scientific and technological progress--computerized industries and the high science-content of production--have so…

Demonstration and Evaluation of an Innovative Water Main Rehabilitation Technology: Spray-on Polymeric Lining

EPA Science Inventory

Many utilities are seeking innovative rehabilitation technologies to extend the life and fix larger portions of their water distribution systems with current funding levels. The information on the capabilities and applicability of new technologies is not always readily available...

Performance Evaluation of Innovative Water Main Rehabilitation Spray-on Lining Product in Somerville, NJ

EPA Science Inventory

Renewal technologies being used for the repair, replacement and/or rehabilitation of deteriorating water distribution systems are generally effective, but there is still considerable room for improvement of these existing technologies and for the development of new technologies. ...

Understanding access and use of technology among youth with first-episode psychosis to inform the development of technology-enabled therapeutic interventions.

PubMed

Abdel-Baki, Amal; Lal, Shalini; D-Charron, Olivier; Stip, Emmanuel; Kara, Nadjia

2017-02-01

Computers, video games and technological devices are part of young people's everyday lives. However, their use in first-episode psychosis (FEP) treatment is rare. The purpose of this study was to better understand the access and use of technology among individuals with FEP, including gaming activities, to inform future development of technology-enabled therapeutic applications. Self-administered survey on use of technological tools in 71 FEP individuals. PCs/laptops were used by all participants; cellphones/smartphones by 92%, consoles by 83% (mainly male and younger participants). Women texted and used social networks more frequently; men played games (mainly action) more often. The younger individuals reported playing games frequently (32% daily) with less use of the Web and social networks (favourite: Facebook). These data will be useful for developing Web-based psychoeducation tools and cognitive remediation video games for youth with FEP. © 2015 Wiley Publishing Asia Pty Ltd.

DNA Microarray Technology

MedlinePlus

Skip to main content DNA Microarray Technology Enter Search Term(s): Español Research Funding An Overview Bioinformatics Current Grants Education and Training Funding Extramural Research News Features Funding Divisions Funding ...

4-Stage Online Presence Model: Model for Module Design and Delivery Using Web 2.0 Technologies to Facilitate Critical Thinking Skills

ERIC Educational Resources Information Center

Goh, WeiWei; Dexter, Barbara; Self, Richard

2014-01-01

The main purpose of this paper is to present a conceptual model for the use of web 2.0 online technologies in order to develop and enhance students' critical thinking skills at higher education level. Wiki is chosen as the main focus in this paper. The model integrates Salmon's 5-stage model (Salmon, 2002) with Garrison's Community of Inquiry…

Caring in an Age of Technology. Proceedings of the International Conference on Counseling in the 21st Century (6th, Beijing, China, May 29-30, 1997).

ERIC Educational Resources Information Center

Evraiff, Bill, Comp.; Evraiff, Lois, Comp.

The two main themes of this conference were the influence of technology on families, and technology and counseling. Many of the papers consider the impact technology is having on individuals and families, and subsequently how it is affecting the counseling profession. This involves new ways of counseling using technological resources, and…

Literature review on monitoring technologies and their outcomes in independently living elderly people.

PubMed

Peetoom, Kirsten K B; Lexis, Monique A S; Joore, Manuela; Dirksen, Carmen D; De Witte, Luc P

2015-07-01

To obtain insight into what kind of monitoring technologies exist to monitor activity in-home, what the characteristics and aims of applying these technologies are, what kind of research has been conducted on their effects and what kind of outcomes are reported. A systematic document search was conducted within the scientific databases Pubmed, Embase, Cochrane, PsycINFO and Cinahl, complemented by Google Scholar. Documents were included in this review if they reported on monitoring technologies that detect activities of daily living (ADL) or significant events, e.g. falls, of elderly people in-home, with the aim of prolonging independent living. Five main types of monitoring technologies were identified: PIR motion sensors, body-worn sensors, pressure sensors, video monitoring and sound recognition. In addition, multicomponent technologies and smart home technologies were identified. Research into the use of monitoring technologies is widespread, but in its infancy, consisting mainly of small-scale studies and including few longitudinal studies. Monitoring technology is a promising field, with applications to the long-term care of elderly persons. However, monitoring technologies have to be brought to the next level, with longitudinal studies that evaluate their (cost-) effectiveness to demonstrate the potential to prolong independent living of elderly persons. [Box: see text].

GUIDANCE OF THE FIELD DEMONSTRATION OF REMEDIATION TECHNOLOGIES

EPA Science Inventory

This paper will focus on the demonstration of hazardous waste cleanup technologies in the field. The technologies will be at the pilot- or full-scale, and further referred to as field-scale. The main objectives of demonstration at the field-scale are development of reliable perfo...

Blended Course Design for Multi-Campus Technology Instruction: An Expository Study

ERIC Educational Resources Information Center

Thrasher, Evelyn; Coleman, Phillip; Willis, Jeffrey

2014-01-01

This manuscript shares the results of an experimental blended course design that combines online and synchronous technology instruction across four geographically dispersed computer classrooms using ITV technology. Lessons learned include equipment requirements, both in the main classroom and remote classrooms, taking insufficient bandwidth into…

Technology for Science: Overview of the Project.

ERIC Educational Resources Information Center

Crismond, David; And Others

Technology for Science is a National Science Foundation funded program that is developing and testing curriculum units for teacher materials built around a series of design-oriented science problems called "challenges," mainly for ninth-grade general and physical science classes. Technology for science challenges have a clear connection…

State of Technology Report for Force Main Rehabilitation

EPA Science Inventory

Force mains that carry sewage flows under pressure represent a special set of challenges for sewer rehabilitation. Force mains represent about 7.5% of the wastewater system and they typically use materials that are not commonly used in gravity sewer systems. Ductile iron (DI), ...

The Effectiveness of Educational Technology Applications for Enhancing Mathematics Achievement in K-12 Classrooms: A Meta-Analysis. Educator's Summary

ERIC Educational Resources Information Center

Center for Research and Reform in Education, 2012

2012-01-01

This review summarizes research on the effects of technology use on mathematics achievement in K-12 classrooms. The main research questions included: (1) Do education technology applications improve mathematics achievement in K-12 classrooms as compared to traditional teaching methods without education technology?; and (2) What study and research…

Crosscutting Technology Development at the Center for Advanced Separation Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher E. Hull

2006-09-30

This Technical Progress Report describes progress made on the twenty nine subprojects awarded in the second year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

CROSSCUTTING TECHNOLOGY DEVELOPMENT AT THE CENTER FOR ADVANCED SEPARATION TECHNOLOGIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher E. Hull

2006-05-15

This Technical Progress Report describes progress made on the twenty nine subprojects awarded in the second year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

Exploring the Main Barriers of Technology Integration in the English Language Teaching Classroom: A Qualitative Study

ERIC Educational Resources Information Center

Khodabandelou, Rouholllah; That, Junny Ei Mon; Anne A/P S. Selvaraju, Melinda; Ken, Tan Yan; Kewen, Zhu; Yan, Zhang; Ning, Tan Yan

2016-01-01

The abundance of technology in recent years has contributed to development in the societies, industries, and education. It is proven from the current trend of technology such as the emergence and rise of smart phones, tablets, laptops and wireless internet connection that the present and future world will be heralded by technology. The integration…

Transition from Realistic to Real World Problems with the Use of Technology in Elementary Mathematical Education

ERIC Educational Resources Information Center

Budinski, Natalija; Milinkovic, Dragica

2017-01-01

The availability of technology has a big impact on education, and that is the main reason for discussing the use of technologies in mathematical education in our paper. The availability of technology influences how mathematical contents could be presented to students. We present the benefits of learning mathematical concepts through real life…

Towards a Differentiated and Domain-Specific View of Educational Technology: An Exploratory Study of History Teachers' Technology Use

ERIC Educational Resources Information Center

Voet, Michiel; De Wever, Bram

2017-01-01

Adopting a differentiated and domain-specific view of educational technology, the present study focuses on the case of school history. It argues that, in this particular context, one of technology's main assets is its ability to support inquiry-based learning activities, during which students interpret the past through historical reasoning. As…

Enrichment of the educational environment with information and communication technologies: state of art at the Faculty of Pharmacy of Kaunas University of Medicine.

PubMed

Butrimiene, Edita; Stankeviciene, Nida

2008-01-01

Both traditional and new educational environments, the latter enriched with information and communication technologies, coexist in today's university. The goal of this article is to present the concept of educational environment enriched with information and communication technologies, to reveal the main features of such environment, and to present the results of certain investigation on the application of information technologies in teaching/learning processes at the Faculty of Pharmacy of Kaunas University of Medicine. The discussion object of this paper is the educational environment enriched with information and communication technologies. In designing the environments of this type, positive aspects of traditional teaching models are being developed by integrating them into the new educational environment. The concept of educational environment enriched with information and communication technologies is reviewed in the first part of this paper. The structure and main features of educational environments enriched with information and communication technologies are highlighted in the second part. The results of the study on the application of information technologies in teaching/learning processes at the Faculty of Pharmacy of Kaunas University of Medicine are presented in the third part.

Main Chamber and Preburner Injector Technology

NASA Technical Reports Server (NTRS)

Santoro, Robert J.; Merkle, Charles L.

1999-01-01

This document reports the experimental and analytical research carried out at the Penn State Propulsion Engineering Research Center in support of NASA's plan to develop advanced technologies for future single stage to orbit (SSTO) propulsion systems. The focus of the work is on understanding specific technical issues related to bi-propellant and tri-propellant thrusters. The experiments concentrate on both cold flow demonstrations and hot-fire uni-element tests to demonstrate concepts that can be incorporated into hardware design and development. The analysis is CFD-based and is intended to support the design and interpretation of the experiments and to extrapolate findings to full-scale designs. The research is divided into five main categories that impact various SSTO development scenarios. The first category focuses on RP-1/gaseous hydrogen (GH2)/gaseous oxygen (GO2) tri-propellant combustion with specific emphasis on understanding the benefits of hydrogen addition to RP-1/oxygen combustion and in developing innovative injector technology. The second category investigates liquid oxygen (LOX)/GH2 combustion at main chamber near stoichiometric conditions to improve understanding of existing LOX/GH2 rocket systems. The third and fourth categories investigate the technical issues related with oxidizer-rich and fuel-rich propulsive concepts, issues that are necessary for developing the full-flow engine cycle. Here, injector technology issues for both LOX/GH2 and LOX/RP-1 propellants are examined. The last category, also related to the full-flow engine cycle, examines injector technology needs for GO2/GH2 propellant combustion at near-stoichiometric conditions for main chamber application.

Techno-Nationalism and the Construction of University Technology Transfer

ERIC Educational Resources Information Center

Sá, Creso; Kretz, Andrew; Sigurdson, Kristjan

2013-01-01

Our historical study of Canada's main research university illuminates the overlooked influence of national identities and interests as forces shaping the institutionalization of technology transfer. Through the use of archival sources we trace the rise and influence of Canadian technological nationalism--a response to Canada's perceived dependency…

The Educational Technology of Ethical Development for Students

ERIC Educational Resources Information Center

Song, Ting; Ustin, Pavel N.; Popov, Leonid M.; Mudarisov, Marat M.

2017-01-01

The relevance of this work was connected with the problem of ethical competencies forming among future psychologists during their learning in university. The first task of research was to work out the technology of ethical development for students-psychologists. The structure of this technology included four main educational components:…

The Technological Diegesis in "The Great Gatsby"

ERIC Educational Resources Information Center

Zhang, Mingquan

2008-01-01

This paper explores the technological diegesis in "The Great Gatsby." In the novel, Fitzgerald cleverly integrates the technological forces into his writing. He particularly relies on the two main props of automobile and telephone to arrange his fragmented plots into a whole. By the deliberate juxtaposition of men and women and machines…

Has Research on Collaborative Learning Technologies Addressed Massiveness? A Literature Review

ERIC Educational Resources Information Center

Manathunga, Kalpani; Hernández-Leo, Davinia

2015-01-01

There is a growing interest in understanding to what extent innovative educational technologies can be used to support massive courses. Collaboration is one of the main desired elements in massive learning actions involving large communities of participants. Accumulated research in collaborative learning technologies has proposed and evaluated…

Demonstration and evaluation of an innovative water main rehabilitation technology: Cured-in-Place Pipe (CIPP) lining

EPA Science Inventory

As many water utilities are seeking new and innovative rehabilitation technologies to extend the life of their water distribution systems, information on the capabilities and applicability of new technologies is not always readily available from an independent source. The U.S. E...

Exploring the Use of Technology in Mentoring

ERIC Educational Resources Information Center

Wilcox, Denise

2017-01-01

Purpose: The purpose of this qualitative case study was to explore how using technology tools during mentoring impacts the desired outcomes, as defined by the mentor-mentee contract, of the mentoring relationships of technology workers at a private graduate university with the main campus in Southern California. Methodology: This was a single…

Research pressure instrumentation for NASA Space Shuttle main engine

NASA Technical Reports Server (NTRS)

Anderson, P. J.; Nussbaum, P.; Gustafson, G.

1984-01-01

The development of prototype pressure transducers which are targeted to meet the Space Shuttle Main Engine SSME performance design goals is discussed. The fabrication, testing and delivery of 10 prototype units is examined. Silicon piezoresistive strain sensing technology is used to achieve the objectives of advanced state-of-the-art pressure sensors in terms of reliability, accuracy and ease of manufacture. Integration of multiple functions on a single chip is the key attribute of this technology.

Titanium dioxide in fuel cell technology: An overview

NASA Astrophysics Data System (ADS)

Abdullah, N.; Kamarudin, S. K.

2015-03-01

Fuel cell technology is one of the alternative energy sources for the next generation. Although this technology has proven to be one of the main methods for producing new energy sources, fuel cell technology still has some problems that hinder fuel cell commercialization. Recently, new ideas on titanium dioxide are introduced as potential solution in several applications in fuel cell technology. Thus, this article presents an overview on the applications of titanium dioxide and highlights the unique properties and benefits of titanium dioxide in fuel cell technology.

The theory and method of variable frequency directional seismic wave under the complex geologic conditions

NASA Astrophysics Data System (ADS)

Jiang, T.; Yue, Y.

2017-12-01

It is well known that the mono-frequency directional seismic wave technology can concentrate seismic waves into a beam. However, little work on the method and effect of variable frequency directional seismic wave under complex geological conditions have been done .We studied the variable frequency directional wave theory in several aspects. Firstly, we studied the relation between directional parameters and the direction of the main beam. Secondly, we analyzed the parameters that affect the beam width of main beam significantly, such as spacing of vibrator, wavelet dominant frequency, and number of vibrator. In addition, we will study different characteristics of variable frequency directional seismic wave in typical velocity models. In order to examine the propagation characteristics of directional seismic wave, we designed appropriate parameters according to the character of direction parameters, which is capable to enhance the energy of the main beam direction. Further study on directional seismic wave was discussed in the viewpoint of power spectral. The results indicate that the energy intensity of main beam direction increased 2 to 6 times for a multi-ore body velocity model. It showed us that the variable frequency directional seismic technology provided an effective way to strengthen the target signals under complex geological conditions. For concave interface model, we introduced complicated directional seismic technology which supports multiple main beams to obtain high quality data. Finally, we applied the 9-element variable frequency directional seismic wave technology to process the raw data acquired in a oil-shale exploration area. The results show that the depth of exploration increased 4 times with directional seismic wave method. Based on the above analysis, we draw the conclusion that the variable frequency directional seismic wave technology can improve the target signals of different geologic conditions and increase exploration depth with little cost. Due to inconvenience of hydraulic vibrators in complicated surface area, we suggest that the combination of high frequency portable vibrator and variable frequency directional seismic wave method is an alternative technology to increase depth of exploration or prospecting.

Biological research survey for the efficient conversion of biomass to biofuels.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kent, Michael Stuart; Andrews, Katherine M.

2007-01-01

The purpose of this four-week late start LDRD was to assess the current status of science and technology with regard to the production of biofuels. The main focus was on production of biodiesel from nonpetroleum sources, mainly vegetable oils and algae, and production of bioethanol from lignocellulosic biomass. One goal was to assess the major technological hurdles for economic production of biofuels for these two approaches. Another goal was to compare the challenges and potential benefits of the two approaches. A third goal was to determine areas of research where Sandia's unique technical capabilities can have a particularly strong impactmore » in these technologies.« less

Health information technology in oncology practice: a literature review.

PubMed

Fasola, G; Macerelli, M; Follador, A; Rihawi, K; Aprile, G; Della Mea, V

2014-01-01

The adoption and implementation of information technology are dramatically remodeling healthcare services all over the world, resulting in an unstoppable and sometimes overwhelming process. After the introduction of the main elements of electronic health records and a description of what every cancer-care professional should be familiar with, we present a narrative review focusing on the current use of computerized clinical information and decision systems in oncology practice. Following a detailed analysis of the many coveted goals that oncologists have reached while embracing informatics progress, the authors suggest how to overcome the main obstacles for a complete physicians' engagement and for a full information technology adoption, and try to forecast what the future holds.

Big data processing in the cloud - Challenges and platforms

NASA Astrophysics Data System (ADS)

Zhelev, Svetoslav; Rozeva, Anna

2017-12-01

Choosing the appropriate architecture and technologies for a big data project is a difficult task, which requires extensive knowledge in both the problem domain and in the big data landscape. The paper analyzes the main big data architectures and the most widely implemented technologies used for processing and persisting big data. Clouds provide for dynamic resource scaling, which makes them a natural fit for big data applications. Basic cloud computing service models are presented. Two architectures for processing big data are discussed, Lambda and Kappa architectures. Technologies for big data persistence are presented and analyzed. Stream processing as the most important and difficult to manage is outlined. The paper highlights main advantages of cloud and potential problems.

Pulsed electron accelerator for radiation technologies in the enviromental applications

NASA Astrophysics Data System (ADS)

Korenev, Sergey

1997-05-01

The project of pulsed electron accelerator for radiation technologies in the environmental applications is considered. An accelerator consists of high voltage generator with vacuum insulation and vacuum diode with plasma cathode on the basis discharge on the surface of dielectric of large dimensions. The main parameters of electron accelerators are following: kinetic energy 0.2 - 2.0 MeV, electron beam current 1 - 30 kA and pulse duration 1- 5 microseconds. The main applications of accelerator for decomposition of wastewaters are considered.

Practical Development of Modern Mass Media Education in Poland

ERIC Educational Resources Information Center

Fedorov, Alexander

2012-01-01

Practical development of modern mass media education in Poland. The paper analyzes the main ways of practical development of modern media education (1992-2012 years) in Poland: basic technologies, main events, etc.

Space Shuttle Project

NASA Image and Video Library

1981-01-01

A Space Shuttle Main Engine undergoes test-firing at the National Space Technology Laboratories (now the Sternis Space Center) in Mississippi. The Marshall Space Flight Center had management responsibility of Space Shuttle propulsion elements, including the Main Engines.

Clathrate compounds and method of manufacturing

DOEpatents

Nolas, George S [Tampa, FL; Witanachchi, Sarath [Tampa, FL; Mukherjee, Pritish [Tampa, FL

2009-05-19

The present invention comprises new materials, material structures, and processes of fabrication of such that may be used in technologies involving the conversion of light to electricity and/or heat to electricity, and in optoelectronics technologies. The present invention provide for the fabrication of a clathrate compound comprising a type II clathrate lattice with atoms of silicon and germanium as a main framework forming lattice spacings within the framework, wherein the clathrate lattice follows the general formula Si.sub.136-yGe.sub.y, where y indicates the number of Ge atoms present in the main framework and 136-y indicates the number of Si atoms present in the main framework, and wherein y>0.

STE thrust chamber technology: Main injector technology program and nozzle Advanced Development Program (ADP)

NASA Technical Reports Server (NTRS)

1993-01-01

The purpose of the STME Main Injector Program was to enhance the technology base for the large-scale main injector-combustor system of oxygen-hydrogen booster engines in the areas of combustion efficiency, chamber heating rates, and combustion stability. The initial task of the Main Injector Program, focused on analysis and theoretical predictions using existing models, was complemented by the design, fabrication, and test at MSFC of a subscale calorimetric, 40,000-pound thrust class, axisymmetric thrust chamber operating at approximately 2,250 psi and a 7:1 expansion ratio. Test results were used to further define combustion stability bounds, combustion efficiency, and heating rates using a large injector scale similar to the Pratt & Whitney (P&W) STME main injector design configuration including the tangential entry swirl coaxial injection elements. The subscale combustion data was used to verify and refine analytical modeling simulation and extend the database range to guide the design of the large-scale system main injector. The subscale injector design incorporated fuel and oxidizer flow area control features which could be varied; this allowed testing of several design points so that the STME conditions could be bracketed. The subscale injector design also incorporated high-reliability and low-cost fabrication techniques such as a one-piece electrical discharged machined (EDMed) interpropellant plate. Both subscale and large-scale injectors incorporated outer row injector elements with scarfed tip features to allow evaluation of reduced heating rates to the combustion chamber.

Educating the Adolescent for Technological Changes: Some Implications for Teaching.

ERIC Educational Resources Information Center

Cheong, Lau Kam

Generally concerned with how the schools can better educate the adolescent for adulthood, this paper briefly discusses the adolescent's need for work as a means of attaining adulthood, some promises and threats of technology, and effects of technological advances on society. Particular attention is given to four main effects having direct…

New Communications Technology and Distance Education: Implications for Commonwealth Countries of the South. Papers on Information Technology No. 239.

ERIC Educational Resources Information Center

Bates, A. W.

This review of the technical possibilities of audio, television, computing, and combination media addresses the main factors influencing decisions about each technology's suitability for distance teaching, including access, costs, symbolic representation, student control, teacher control, existing structures, learning skills to be developed, and…

Testing the Utility of Person-Environment Correspondence Theory with Instructional Technology Students in Turkey

ERIC Educational Resources Information Center

Perkmen, Serkan

2012-01-01

The main objective of this study was to examine the validity and usefulness of the person-environment correspondence theory with instructional technology students in Turkey. The participants included 211 students and three teachers. Results revealed that instructional technology students value achievement most and that they believe that entering a…

Research on the Scientific and Technological Innovation of Research University and Its Strategic Measures

ERIC Educational Resources Information Center

Cheng, Yongbo; Ge, Shaowei

2005-01-01

This paper illustrates the important role that the scientific and technological innovation plays in the research university. Technological innovation is one of the main functions that the research university serves and contributes for the development of economy and society, which is the essential measure for Research University to promote…

[Nuclear medicine in Spain: high technology 2013].

PubMed

Soriano Castrejón, A M; Prats Rivera, E; Alonso Farto, J C; Vallejo Casas, J A; Rodriguez Gasen, A; Setoain Perego, J; Arbizu Lostao, J

2014-01-01

This article details the high technology equipment in Spain obtained through a survey sent to the three main provider companies of equipment installed in Spain. The geographical distribution of high technology by Autonomous Communities and its antiquity have been analyzed. Copyright © 2014 Elsevier España, S.L.U. y SEMNIM. All rights reserved.

Teaching and Learning with Technology: Effectiveness of ICT Integration in Schools

ERIC Educational Resources Information Center

Ghavifekr, Simin; Rosdy, Wan Athirah Wan

2015-01-01

Integration of Information, Communication, and Technology (ICT) will assist teachers to the global requirement to replace traditional teaching methods with a technology-based teaching and learning tools and facilities. In Malaysia, ICT is considered as one of the main elements in transforming the country to the future development. The Ministry of…

Are Digital Natives a Myth or Reality? University Students' Use of Digital Technologies

ERIC Educational Resources Information Center

Margaryan, Anoush; Littlejohn, Allison; Vojt, Gabrielle

2011-01-01

This study investigated the extent and nature of university students' use of digital technologies for learning and socialising. The findings show that students use a limited range of mainly established technologies. Use of collaborative knowledge creation tools, virtual worlds, and social networking sites was low. "Digital natives" and students of…

Teachers' Perceptions of Factors Affecting the Educational Use of ICT in Technology-Rich Classrooms

ERIC Educational Resources Information Center

Badia, Antoni; Meneses, Julio; Sigales, Carles

2013-01-01

Introduction: The purpose of this study is to identify the main factors that influence teachers' decision-making regarding the educational use of ICT (Information and Communication Technologies) in technology-rich classrooms. Method: We collected data from 278 teachers in Catalonia (Spain) working in eight primary and secondary education schools…

Seamless Support: Technology Enhanced Learning in Open Distance Learning at NWU

ERIC Educational Resources Information Center

Esterhuizen, Hennie

2015-01-01

Frantic attempts of investing in technology to demonstrate willingness to educate for the knowledge society may result in failure to address the real requirements. This paper presents the main features of a framework for integrating Technology Enhanced Learning in Open Distance Learning at North-West University, South Africa. Support towards…

Role of Mobile Technology in Promoting Campus-Wide Learning Environment

ERIC Educational Resources Information Center

Hussain, Irshad; Adeeb, Muhammad Aslam

2009-01-01

The present study examines the role of mobile technology in promoting campus-wide learning environment. Its main objectives were to a) evaluate the role of mobile technology in higher education in terms of its i). appropriateness ii). flexibility iii). Interactivity, & iv). availability & usefulness and to b). identify the problems of…

Work and technological innovation in organic agriculture.

PubMed

Tereso, M J A; Abrahão, R F; Gemma, S F B; Montedo, U B; Menegon, N L; Guarneti, J E; Ribeiro, I A V

2012-01-01

Organic agriculture is a sustainable cultivation ecologically, economically and socially. Several researches in organic agriculture have been made from technical perspectives, economic traits or related to ecological aspects. There are practically no investigations into the nature of the technology used in organic agriculture, especially from an ergonomic perspective. From the activity analysis, this study aimed to map the technology used in the production of organic vegetables. Properties producing organic vegetables were selected representing the State of São Paulo. It was applied an instrument (questionnaire and semi-structured interview) with their managers and it was made visual records to identify adaptations, innovations and technological demands that simultaneously minimize the workload and the difficulties in performing the tasks and increase work productivity. For some of the technological innovations a digital scanner was used to generate a virtual solid model to facilitate its redesign and virtual prototyping. The main results show that organic farmers have little technology in product form. The main innovations that enable competitive advantage or allow higher labor productivity occur in the form of processes, organization and marketing.

Data Movement Dominates: Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacob, Bruce L.

Over the past three years in this project, what we have observed is that the primary reason for data movement in large-scale systems is that the per-node capacity is not large enough—i.e., one of the solutions to the data-movement problem (certainly not the only solution that is required, but a significant one nonetheless) is to increase per-node capacity so that inter-node traffic is reduced. This unfortunately is not as simple as it sounds. Today’s main memory systems for datacenters, enterprise computing systems, and supercomputers, fail to provide high per-socket capacity [Dirik & Jacob 2009; Cooper-Balis et al. 2012], except atmore » extremely high price points (factors of 10–100x the cost/bit of consumer main-memory systems) [Stokes 2008]. The reason is that our choice of technology for today’s main memory systems—i.e., DRAM, which we have used as a main-memory technology since the 1970s [Jacob et al. 2007]—can no longer keep up with our needs for density and price per bit. Main memory systems have always been built from the cheapest, densest, lowest-power memory technology available, and DRAM is no longer the cheapest, the densest, nor the lowest-power storage technology out there. It is now time for DRAM to go the way that SRAM went: move out of the way for a cheaper, slower, denser storage technology, and become a cache instead. This inflection point has happened before, in the context of SRAM yielding to DRAM. There was once a time that SRAM was the storage technology of choice for all main memories [Tomasulo 1967; Thornton 1970; Kidder 1981]. However, once DRAM hit volume production in the 1970s and 80s, it supplanted SRAM as a main memory technology because it was cheaper, and it was denser. It also happened to be lower power, but that was not the primary consideration of the day. At the time, it was recognized that DRAM was much slower than SRAM, but it was only at the supercomputer level (For instance the Cray X-MP in the 1980s and its follow-on, the Cray Y-MP, in the 1990s) that could one afford to build ever- larger main memories out of SRAM—the reasoning for moving to DRAM was that an appropriately designed memory hierarchy, built of DRAM as main memory and SRAM as a cache, would approach the performance of SRAM, at the price-per-bit of DRAM [Mashey 1999]. Today it is quite clear that, were one to build an entire multi-gigabyte main memory out of SRAM instead of DRAM, one could improve the performance of almost any computer system by up to an order of magnitude—but this option is not even considered, because to build that system would be prohibitively expensive. It is now time to revisit the same design choice in the context of modern technologies and modern systems. For reasons both technical and economic, we can no longer afford to build ever-larger main memory systems out of DRAM. Flash memory, on the other hand, is significantly cheaper and denser than DRAM and therefore should take its place. While it is true that flash is significantly slower than DRAM, one can afford to build much larger main memories out of flash than out of DRAM, and we show that an appropriately designed memory hierarchy, built of flash as main memory and DRAM as a cache, will approach the performance of DRAM, at the price-per-bit of flash. In our studies as part of this project, we have investigated Non-Volatile Main Memory (NVMM), a new main-memory architecture for large-scale computing systems, one that is specifically designed to address the weaknesses described previously. In particular, it provides the following features: non-volatility: The bulk of the storage is comprised of NAND flash, and in this organization DRAM is used only as a cache, not as main memory. Furthermore, the flash is journaled, which means that operations such as checkpoint/restore are already built into the system. 1+ terabytes of storage per socket: SSDs and DRAM DIMMs have roughly the same form factor (several square inches of PCB surface area), and terabyte SSDs are now commonplace. performance approaching that of DRAM: DRAM is used as a cache to the flash system. price-per-bit approaching that of NAND: Flash is currently well under $0.50 per gigabyte; DDR3 SDRAM is currently just over $10 per gigabyte [Newegg 2014]. Even today, one can build an easily affordable main memory system with a terabyte or more of NAND storage per CPU socket (which would be extremely expensive were one to use DRAM), and our cycle- accurate, full-system experiments show that this can be done at a performance point that lies within a factor of two of DRAM.« less

Technology-Induced Risks in History

NASA Astrophysics Data System (ADS)

Rabkin, Ya.

Our perception of risk contains three main aspects: (1) probability of the risk occurring; (2) the extent of possible damage; (3) the degree of voluntary or involuntary exposure to risk. History of risk assessment has been traced in several areas, such as transportation, and has largely focused on insurance. Construction projects constitute one of the oldest areas of technology where accidents continue to occur, while health has always been a fragile commodity. Urbanization has multiplied the risks of illness and death, while natural catastrophes, though still frightening, have ceded their central place to technology-based disasters in the Western perceptions of risk. The human has become the main source of danger to the very survival of the planet. The Enlightenment utopia of scientific progress resulting in social and moral progress of humanity has collided with the awareness of new technology induced risks. Life on Earth began without humans, and it may end without them. Our civilization is the first that faces an end to be brought about by our own technological ingenuity.

Prospective study of luminous radiation associated technology photosensitive compounds for treatment of diseases

NASA Astrophysics Data System (ADS)

Pires-Santos, Gustavo M.; de Oliveira, Susana C. P. S.; Monteiro, Juliana S. C.; Sampaio, Fernando José P.; Brugnera, Aldo; Zanin, Fátima Antônia A.; Almeida, Paulo; Pinheiro, Antônio L. B.

2015-03-01

Prospective studies are based on the analysis of patent documents and aims to assess the both technological history and development providing innovation opportunities. This study was a technological prospection mapping aiming to identify breakthrough in PDT and the new possibilities of the technology. Therefore, research in the bank patent 'Spacenet Patent Search' was performed using determinants descriptors associated with the theme: 'A61K41', 'A61N5 / 06'. Were analyzed in this study 326 documents. In evaluating these patents, it was possible to observe an increase in the number of deposits over time, with peak between 1990 and 2000. The highest number of inventors of this area are part of the private sector and the US appear as main producer of technology. It was also observed that blue light, porphyrins and their derivatives are the main topics. It may be concluded that PDT still offers a large opportunity for growth as several wavelengths, and photosensitizers that may be used in the technique.

Wearable smart systems: from technologies to integrated systems.

PubMed

Lymberis, A

2011-01-01

Wearable technology and integrated systems, so called Smart Wearable Systems (SWS) have demonstrated during the last 10-15 years significant advances in terms of, miniaturisation, seamless integration, data processing & communication, functionalisation and comfort. This is mainly due to the huge progress in sciences and technologies e.g. biomedical and micro & nano technologies, but also to a strong demand for new applications such as continuous personal health monitoring, healthy lifestyle support, human performance monitoring and support of professionals at risk. Development of wearable systems based of smart textile have, in addition, benefited from the eagerness of textile industry to develop new value-added apparel products like functionalized garments and smart clothing. Research and development in these areas has been strongly promoted worldwide. In Europe the major R&D activities were supported through the Information & Communication Technologies (ICT) priority of the R&D EU programs. The paper presents and discusses the main achievements towards integrated systems as well as future challenges to be met in order to reach a market with reliable and high value-added products.

Propulsion Integrated Vehicle Health Management Technology Experiment (PITEX) Conducted

NASA Technical Reports Server (NTRS)

Maul, William A.; Chicatelli, Amy K.; Fulton, Christopher E.

2004-01-01

The Propulsion Integrated Vehicle Health Management (IVHM) Technology Experiment (PITEX) is a continuing NASA effort being conducted cooperatively by the NASA Glenn Research Center, the NASA Ames Research Center, and the NASA Kennedy Space Center. It was a key element of a Space Launch Initiative risk-reduction task performed by the Northrop Grumman Corporation in El Segundo, California. PITEX's main objectives are the continued maturation of diagnostic technologies that are relevant to second generation reusable launch vehicle (RLV) subsystems and the assessment of the real-time performance of the PITEX diagnostic solution. The PITEX effort has considerable legacy in the NASA IVHM Technology Experiment for X-vehicles (NITEX) that was selected to fly on the X-34 subscale RLV that was being developed by Orbital Sciences Corporation. NITEX, funded through the Future-X Program Office, was to advance the technology-readiness level of selected IVHM technologies within a flight environment and to begin the transition of these technologies from experimental status into RLV baseline designs. The experiment was to perform realtime fault detection and isolation and suggest potential recovery actions for the X-34 main propulsion system (MPS) during all mission phases by using a combination of system-level analysis and detailed diagnostic algorithms.

Effect of Shrouding Gas Temperature on Characteristics of a Supersonic Jet Flow Field with a Shrouding Laval Nozzle Structure

NASA Astrophysics Data System (ADS)

Liu, Fuhai; Sun, Dongbai; Zhu, Rong; Li, Yilin

2018-05-01

Coherent jet technology was been widely used in the electric arc furnace steelmaking process to protect the kinetic energy of supersonic oxygen jets and achieve a better mixing effect. For this technology, the total temperature distribution of the shrouding jet has a great impact on the velocity of the main oxygen jet. In this article, a supersonic shrouding nozzle using a preheating shrouding jet is proposed to increase the shrouding jet velocity. Both numerical simulation and experimental studies were carried out to analyze its effect on the axial velocity, total temperature and turbulence kinetic energy profiles of the main oxygen jet. Based on these results, it was found that a significant amount of kinetic energy was removed from the main oxygen jet when it passed though the shock wave using a high-temperature shrouding jet, which made the average axial velocity of the coherent jet lower than for a conventional jet in the potential core region. However, the supersonic shrouding nozzle and preheating technology employed for this nozzle design significantly improved the shrouding gas velocity, forming a low-density gas zone at the exit of the main oxygen jet and prolonging the velocity potential core length.

Technology Assessment Need: Review on Attractiveness and Competitiveness

NASA Astrophysics Data System (ADS)

Salwa Sait, Siti; Merlinda Muharam, Farrah; Chin, Thoo Ai; Sulaiman, Zuraidah

2017-06-01

Technology assessment is crucial in managing technology for the purpose of technology exploitation. With business environment continuously changing, firms have to address this issue critically as technology is considered one of the important elements to evaluate performance and gain competitive advantage. Missteps in deciding the best technology to be developed, employed or maintained would cost the firm overall value. To fulfil the need of finding the appropriate scale to assess suitable technology, this paper summarizes that technology assessment (TA) should cover two main aspects, namely technology attractiveness and competitiveness. These components are seen capable to link the scale suggested towards evaluation of financial and non-financial performance towards competitive advantage.

Software Engineering Research/Developer Collaborations in 2005

NASA Technical Reports Server (NTRS)

Pressburger, Tom

2006-01-01

In CY 2005, three collaborations between software engineering technology providers and NASA software development personnel deployed three software engineering technologies on NASA development projects (a different technology on each project). The main purposes were to benefit the projects, infuse the technologies if beneficial into NASA, and give feedback to the technology providers to improve the technologies. Each collaboration project produced a final report. Section 2 of this report summarizes each project, drawing from the final reports and communications with the software developers and technology providers. Section 3 indicates paths to further infusion of the technologies into NASA practice. Section 4 summarizes some technology transfer lessons learned. Also included is an acronym list.

Lignocellulosic ethanol: Technology design and its impact on process efficiency.

PubMed

Paulova, Leona; Patakova, Petra; Branska, Barbora; Rychtera, Mojmir; Melzoch, Karel

2015-11-01

This review provides current information on the production of ethanol from lignocellulosic biomass, with the main focus on relationships between process design and efficiency, expressed as ethanol concentration, yield and productivity. In spite of unquestionable advantages of lignocellulosic biomass as a feedstock for ethanol production (availability, price, non-competitiveness with food, waste material), many technological bottlenecks hinder its wide industrial application and competitiveness with 1st generation ethanol production. Among the main technological challenges are the recalcitrant structure of the material, and thus the need for extensive pretreatment (usually physico-chemical followed by enzymatic hydrolysis) to yield fermentable sugars, and a relatively low concentration of monosaccharides in the medium that hinder the achievement of ethanol concentrations comparable with those obtained using 1st generation feedstocks (e.g. corn or molasses). The presence of both pentose and hexose sugars in the fermentation broth, the price of cellulolytic enzymes, and the presence of toxic compounds that can inhibit cellulolytic enzymes and microbial producers of ethanol are major issues. In this review, different process configurations of the main technological steps (enzymatic hydrolysis, fermentation of hexose/and or pentose sugars) are discussed and their efficiencies are compared. The main features, benefits and drawbacks of simultaneous saccharification and fermentation (SSF), simultaneous saccharification and fermentation with delayed inoculation (dSSF), consolidated bioprocesses (CBP) combining production of cellulolytic enzymes, hydrolysis of biomass and fermentation into one step, together with an approach combining utilization of both pentose and hexose sugars are discussed and compared with separate hydrolysis and fermentation (SHF) processes. The impact of individual technological steps on final process efficiency is emphasized and the potential for use of immobilized biocatalysts is considered. Copyright © 2014 Elsevier Inc. All rights reserved.

Micro-fabrication method of graphite mesa microdevices based on optical lithography technology

NASA Astrophysics Data System (ADS)

Zhang, Cheng; Wen, Donghui; Zhu, Huamin; Zhang, Xiaorui; Yang, Xing; Shi, Yunsheng; Zheng, Tianxiang

2017-12-01

Graphite mesa microdevices have incommensurate contact nanometer interfaces, superlubricity, high-speed self-retraction, and other characteristics, which have potential applications in high-performance oscillators and micro-scale switches, memory devices, and gyroscopes. However, the current method of fabricating graphite mesa microdevices is mainly based on high-cost, low efficiency electron beam lithography technology. In this paper, the processing technologies of graphite mesa microdevices with various shapes and sizes were investigated by a low-cost micro-fabrication method, which was mainly based on optical lithography technology. The characterization results showed that the optical lithography technology could realize a large-area of patterning on the graphite surface, and the graphite mesa microdevices, which have a regular shape, neat arrangement, and high verticality could be fabricated in large batches through optical lithography technology. The experiments and analyses showed that the graphite mesa microdevices fabricated through optical lithography technology basically have the same self-retracting characteristics as those fabricated through electron beam lithography technology, and the maximum size of the graphite mesa microdevices with self-retracting phenomenon can reach 10 µm  ×  10 µm. Therefore, the proposed method of this paper can realize the high-efficiency and low-cost processing of graphite mesa microdevices, which is significant for batch fabrication and application of graphite mesa microdevices.

Active learning in optics and photonics: Liquid Crystal Display in the do-it-yourself

NASA Astrophysics Data System (ADS)

Vauderwange, Oliver; Haiss, Ulrich; Wozniak, Peter; Israel, Kai; Curticapean, Dan

2015-10-01

Monitors are in the center of media productions and hold an important function as the main visual interface. Tablets and smartphones are becoming more and more important work tools in the media industry. As an extension to our lecture contents an intensive discussion of different display technologies and its applications is taking place now. The established LCD (Liquid Crystal Display) technology and the promising OLED (Organic Light Emitting Diode) technology are in the focus. The classic LCD is currently the most important display technology. The paper will present how the students should develop sense for display technologies besides the theoretical scientific basics. The workshop focuses increasingly on the technical aspects of the display technology and has the goal of deepening the students understanding of the functionality by building simple Liquid Crystal Displays by themselves. The authors will present their experience in the field of display technologies. A mixture of theoretical and practical lectures has the goal of a deeper understanding in the field of digital color representation and display technologies. The design and development of a suitable learning environment with the required infrastructure is crucial. The main focus of this paper is on the hands-on optics workshop "Liquid Crystal Display in the do-it-yourself".

The Community College of Maine Annual Report, Year Two, 1990-1991.

ERIC Educational Resources Information Center

Maine Univ., Augusta. Office of Distance Education.

The Community College of Maine (CCM) makes use of new telecommunications and information technologies to overcome the barriers of geography, cost, and time that have always limited access to higher education for Maine's rural communities. Currently, the Interactive Television System (ITV) is the primary means used to broadcast CCM courses, but…

Education technology with continuous real time monitoring of the current functional and emotional students' states

NASA Astrophysics Data System (ADS)

Alyushin, M. V.; Kolobashkina, L. V.

2017-01-01

The education technology with continuous monitoring of the current functional and emotional students' states is suggested. The application of this technology allows one to increase the effectiveness of practice through informed planning of the training load. For monitoring the current functional and emotional students' states non-contact remote technologies of person bioparameters registration are encouraged to use. These technologies are based on recording and processing in real time the main person bioparameters in a purely passive mode. Experimental testing of this technology has confirmed its effectiveness.

Augmented reality technology for preoperative planning and intraoperative navigation during hepatobiliary surgery: A review of current methods.

PubMed

Tang, Rui; Ma, Long-Fei; Rong, Zhi-Xia; Li, Mo-Dan; Zeng, Jian-Ping; Wang, Xue-Dong; Liao, Hong-En; Dong, Jia-Hong

2018-04-01

Augmented reality (AR) technology is used to reconstruct three-dimensional (3D) images of hepatic and biliary structures from computed tomography and magnetic resonance imaging data, and to superimpose the virtual images onto a view of the surgical field. In liver surgery, these superimposed virtual images help the surgeon to visualize intrahepatic structures and therefore, to operate precisely and to improve clinical outcomes. The keywords "augmented reality", "liver", "laparoscopic" and "hepatectomy" were used for searching publications in the PubMed database. The primary source of literatures was from peer-reviewed journals up to December 2016. Additional articles were identified by manual search of references found in the key articles. In general, AR technology mainly includes 3D reconstruction, display, registration as well as tracking techniques and has recently been adopted gradually for liver surgeries including laparoscopy and laparotomy with video-based AR assisted laparoscopic resection as the main technical application. By applying AR technology, blood vessels and tumor structures in the liver can be displayed during surgery, which permits precise navigation during complex surgical procedures. Liver transformation and registration errors during surgery were the main factors that limit the application of AR technology. With recent advances, AR technologies have the potential to improve hepatobiliary surgical procedures. However, additional clinical studies will be required to evaluate AR as a tool for reducing postoperative morbidity and mortality and for the improvement of long-term clinical outcomes. Future research is needed in the fusion of multiple imaging modalities, improving biomechanical liver modeling, and enhancing image data processing and tracking technologies to increase the accuracy of current AR methods. Copyright © 2018 First Affiliated Hospital, Zhejiang University School of Medicine in China. Published by Elsevier B.V. All rights reserved.

Potential for Landing Gear Noise Reduction on Advanced Aircraft Configurations

NASA Technical Reports Server (NTRS)

Thomas, Russell H.; Nickol, Craig L.; Burley, Casey L.; Guo, Yueping

2016-01-01

The potential of significantly reducing aircraft landing gear noise is explored for aircraft configurations with engines installed above the wings or the fuselage. An innovative concept is studied that does not alter the main gear assembly itself but does shorten the main strut and integrates the gear in pods whose interior surfaces are treated with acoustic liner. The concept is meant to achieve maximum noise reduction so that main landing gears can be eliminated as a major source of airframe noise. By applying this concept to an aircraft configuration with 2025 entry-into-service technology levels, it is shown that compared to noise levels of current technology, the main gear noise can be reduced by 10 EPNL dB, bringing the main gear noise close to a floor established by other components such as the nose gear. The assessment of the noise reduction potential accounts for design features for the advanced aircraft configuration and includes the effects of local flow velocity in and around the pods, gear noise reflection from the airframe, and reflection and attenuation from acoustic liner treatment on pod surfaces and doors. A technical roadmap for maturing this concept is discussed, and the possible drag increase at cruise due to the addition of the pods is identified as a challenge, which needs to be quantified and minimized possibly with the combination of detailed design and application of drag reduction technologies.

Spacewire Routers Implemented with FPGA Technology

NASA Astrophysics Data System (ADS)

Habinc, Sandi; Isomaki, Marko

2011-08-01

Routers are an integral part of SpaceWire networks. Aeroflex Gaisler has developed a highly configurable SpaceWire router VHDL IP core to meet the needs for technology independent router designs. The main design goals have been configurability, technology independence, support of the standard and expandability. The IP core being technologically independent allows it to be used in both ASIC and FPGA technology. The latter is now being used to produce versatile standard products that can reach the market faster than for example an ASIC based product.

SSTAC/ARTS Review of the Draft Integrated Technology Plan (ITP). Volume 2: Propulsion Systems

NASA Technical Reports Server (NTRS)

1991-01-01

The topics addressed are: (1) space propulsion technology program overview; (2) space propulsion technology program fact sheet; (3) low thrust propulsion; (4) advanced propulsion concepts; (5) high-thrust chemical propulsion; (6) cryogenic fluid management; (7) NASA CSTI earth-to-orbit propulsion; (8) advanced main combustion chamber program; (9) earth-to-orbit propulsion turbomachinery; (10) transportation technology; (11) space chemical engines technology; (12) nuclear propulsion; (13) spacecraft on-board propulsion; and (14) low-cost commercial transport.

Li-Ion Battery for ISS

NASA Technical Reports Server (NTRS)

Dalton, Penni; Cohen, Fred

2004-01-01

The ISS currently uses Ni-H2 batteries in the main power system. Although Ni-H2 is a robust and reliable system, recent advances in battery technology have paved the way for future replacement batteries to be constructed using Li-ion technology. This technology will provide lower launch weight as well as increase ISS electric power system (EPS) efficiency. The result of incorporating this technology in future re-support hardware will be greater power availability and reduced program cost. the presentations of incorporating the new technology.

Biogas from Marine Macroalgae: a New Environmental Technology — Life Cycle Inventory for a Further LCA

NASA Astrophysics Data System (ADS)

Romagnoli, Francesco; Blumberga, Dagnija; Gigli, Emanuele

2010-01-01

The main goal of this paper is to analyze the innovative process of production of biogas (via fermentation processes) using marine macroalgae as feedstock in a pilot project plant in Augusta (Sicily, Italy). Algae, during their growth, have the capacity to assimilate nutrients and thus subsequent harvesting of the algal biomass recovers the nutrients from biowaste sources giving the possibility to transform negative environmental externalities in positive mainly in terms of eutrophication and climate change impact categories. The paper presents a novel environmental technology for the production of biogas and 2nd generation biofuel (liquid biomethane) after an upgrading process through the use of a cryogenic technology. The paper would also like to make the first attempt at understanding the possibility to implement this innovative technology in the Latvian context. The first calculations and assumptions for the Life Cycle Inventory for a further Life Cycle Assessment are presented.

A review on architectures and communications technologies for wearable health-monitoring systems.

PubMed

Custodio, Víctor; Herrera, Francisco J; López, Gregorio; Moreno, José Ignacio

2012-10-16

Nowadays society is demanding more and more smart healthcare services that allow monitoring patient status in a non-invasive way, anywhere and anytime. Thus, healthcare applications are currently facing important challenges guided by the u-health (ubiquitous health) and p-health (pervasive health) paradigms. New emerging technologies can be combined with other widely deployed ones to develop such next-generation healthcare systems. The main objective of this paper is to review and provide more details on the work presented in "LOBIN: E-Textile and Wireless-Sensor-Network-Based Platform for Healthcare Monitoring in Future Hospital Environments", published in the IEEE Transactions on Information Technology in Biomedicine, as well as to extend and update the comparison with other similar systems. As a result, the paper discusses the main advantages and disadvantages of using different architectures and communications technologies to develop wearable systems for pervasive healthcare applications.

A Review on Architectures and Communications Technologies for Wearable Health-Monitoring Systems

PubMed Central

Custodio, Víctor; Herrera, Francisco J.; López, Gregorio; Moreno, José Ignacio

2012-01-01

Nowadays society is demanding more and more smart healthcare services that allow monitoring patient status in a non-invasive way, anywhere and anytime. Thus, healthcare applications are currently facing important challenges guided by the u-health (ubiquitous health) and p-health (pervasive health) paradigms. New emerging technologies can be combined with other widely deployed ones to develop such next-generation healthcare systems. The main objective of this paper is to review and provide more details on the work presented in “LOBIN: E-Textile and Wireless-Sensor-Network-Based Platform for Healthcare Monitoring in Future Hospital Environments”, published in the IEEE Transactions on Information Technology in Biomedicine, as well as to extend and update the comparison with other similar systems. As a result, the paper discusses the main advantages and disadvantages of using different architectures and communications technologies to develop wearable systems for pervasive healthcare applications. PMID:23202028

Influence of Augmented Reality Technology upon Pupils' Knowledge about Human Digestive System: The Results of the Experiment

ERIC Educational Resources Information Center

Vilkoniene, Margarita

2009-01-01

Applying information technologies in the educational process is the main direction of modern education. However, "moving" information communication technologies to schools is the primary purpose of discussions held by pedagogical and scientific society as this is a very problematic field (Lamanauskas, 2006). Most of the researches show…

Music Technology Competencies for Education: A Proposal for a Pedagogical Architecture for Distance Learning

ERIC Educational Resources Information Center

Rosas, Fátima Weber; Rocha Machado, Leticia; Behar, Patricia Alejandra

2016-01-01

This article proposes a pedagogical architecture (PA) focused on the development of competencies for music technology in education. This PA used free Web 3.0 technologies, mainly those related to production and musical composition. The pedagogical architecture is geared for teachers and those pursing a teaching degree, working in distance…

Barriers to the Implementation of Electronic Learning in Governmental Organizations: Case of Iran

ERIC Educational Resources Information Center

Jahromi, Gelayol Safavi; Nikabadi, Mohsen Shafiei; Maleki, Morteza

2017-01-01

New developments in technology, particularly the information technology, have changed the perception of learning. These changes have made distance learning an important part of education. However, it seems that this technology does not have a strong position in governmental organizations yet. Therefore, the main goal of this research is to present…

Provision of Educational Technology at Secondary School Level in North West Frontier Province Pakistan

ERIC Educational Resources Information Center

Akhtar, Sajjad Hayat

2008-01-01

Purpose: The study looked into a descriptive research to evaluate the use of educational technology at secondary school level North West Frontier Province (Pakistan). The study has defined the availability, usefulness, problems, emerging trends and status of educational technology. The main focus of the study was the utilization and availability…

Integrating Information Technology's Competencies into Academic Nursing Education--An Action Study

ERIC Educational Resources Information Center

Gonen, Ayala; Sharon, Dganit; Lev-Ari, Lilac

2016-01-01

Today, in the digital age, we are committed to prepare the future nurse for the information technology-rich workplace, and to help them reducing the "shock reality" upon arriving at the clinical setting. The main aim of the study is to promote the knowledge of Information Competencies Technology among nurses' educators and student. The…

University Technology and Research Parks. Panacea or Menace for Engineering Education?

ERIC Educational Resources Information Center

Chatziioanou, Alypios; Sullivan, Edward

2004-01-01

This paper discusses the history, prospects and impacts of university technology and research parks. The main question addressed is: what are the short-term and long-term impacts of such parks on engineering education and its mission? The first technology park, at Stanford, and other early parks are used as examples to assess some of these…

Web3D Technologies in Learning, Education and Training: Motivations, Issues, Opportunities

ERIC Educational Resources Information Center

Chittaro, Luca; Ranon, Roberto

2007-01-01

Web3D open standards allow the delivery of interactive 3D virtual learning environments through the Internet, reaching potentially large numbers of learners worldwide, at any time. This paper introduces the educational use of virtual reality based on Web3D technologies. After briefly presenting the main Web3D technologies, we summarize the…

Factors Influencing New Entrant Dairy Farmer's Decision-Making Process around Technology Adoption

ERIC Educational Resources Information Center

McDonald, Roberta; Heanue, Kevin; Pierce, Karina; Horan, Brendan

2016-01-01

Purpose: The aims of this paper are to (1) evaluate the main factors influencing grazing system technology adoption among new entrant (NE) dairy farmers within Europe and the Irish pasture-based dairy industry, and (2) to determine the extent to which economic factors influence decision-making around technology adoption and use among NEs to the…

Awareness Knowledge Attitude Skills of Telemedicine among Health Professional Faculty Working in Teaching Hospitals

ERIC Educational Resources Information Center

Zayapragassarazan, Zayabalaradjane; Kumar, Santosh

2016-01-01

Introduction: Telemedicine is an emerging technology in health sector in India. The success of any new technology depends on many factors including the knowledge and understanding of the concept, skills acquired, attitude towards technology and working environment by the concerned professionals. Aim: The main objective of this study was to assess…

Developing Argumentation Ability as a Way to Promote Technological Literacy

ERIC Educational Resources Information Center

Choresh, Cilla; Mevarech, Zemira R.; Frank, Moti

2009-01-01

The main purpose of this study is to investigate the effects of three instructional methods on students' technological literacy (TL) and argumentation ability. Participants were 285 seventh grade Israeli boys and girls (12-13-year-old) who studied in 18 technology classes in four junior high schools. The three teaching methods were: (a) teaching…

Influencing Factors for Adopting Technology Enhanced Learning in the Medical Schools of Punjab, Pakistan

ERIC Educational Resources Information Center

Iqbal, Shazia; Ahmad, Shahzad; Willis, Ian

2017-01-01

As the successful establishment of technology supported educational systems requires wide investment in terms of finances and faculty time, this study explores the influencing factors in the adoption of Technology Enhanced Learning (TEL) and the main barriers encountered during the use of TEL in Punjab, Pakistan. Semi-structured interviews were…

Multimedia Image Technology and Computer Aided Manufacturing Engineering Analysis

NASA Astrophysics Data System (ADS)

Nan, Song

2018-03-01

Since the reform and opening up, with the continuous development of science and technology in China, more and more advanced science and technology have emerged under the trend of diversification. Multimedia imaging technology, for example, has a significant and positive impact on computer aided manufacturing engineering in China. From the perspective of scientific and technological advancement and development, the multimedia image technology has a very positive influence on the application and development of computer-aided manufacturing engineering, whether in function or function play. Therefore, this paper mainly starts from the concept of multimedia image technology to analyze the application of multimedia image technology in computer aided manufacturing engineering.

The next generation CdTe technology- Substrate foil based solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferekides, Chris

The main objective of this project was the development of one of the most promising Photovoltaic (PV) materials CdTe into a versatile, cost effective, and high throughput technology, by demonstrating substrate devices on foil substrates using high throughput fabrication conditions. The typical CdTe cell is of the superstrate configuration where the solar cell is fabricated on a glass superstrate by the sequential deposition of a TCO, n-type heterojunction partner, p-CdTe absorber, and back contact. Large glass modules are heavy and present significant challenges during manufacturing (uniform heating, etc.). If a substrate CdTe cell could be developed (the main goal ofmore » this project) a roll-to-toll high throughput technology could be developed.« less

FOREWORD International Conference on Defects in Insulating Materials

NASA Astrophysics Data System (ADS)

Valerio, Mário Ernesto Giroldo; Jackson, R. A.

2010-11-01

These proceedings represent a sample of the scientific works presented during ICDIM2008, the 16th International Conference on Defects in Insulating Materials, held at the Federal University of Sergipe, Aracaju, Brazil from 24-29 August 2008. The conference was the latest in a series which began at Argonne in 1956, and which has been held most recently in Riga, Latvia (2004) and Johannesburg, South Africa (2000). The conference was also related scientifically to the EURODIM series, which have been held most recently in Milan, Italy (2006), Wroclaw, Poland (2002) and Pecs, Hungary (2010). The aim of the conference was to bring together physicists, chemists and materials scientist to discuss defects in insulating materials and their effect on materials, including their optical, mass/charge transport, energy storage and sensor properties. The conference featured 6 plenary lectures, 60 contributed lectures and about 130 posters. The posters were displayed for the whole conference, but discussed in two three-hour sessions. We are grateful to the International Advisory Committee for suggesting invited speakers and to the Programme Committee for their help in refereeing all the abstracts and choosing the contributed oral contributions. We would also like to thank the Local Organising Committee and the Brazilian Physical Society for their help with local organisation and the online registration/payment process respectively. The chairpersons would like to specially thanks all the sponsors listed below for financial support. The Federal University of Sergipe, one of the public and 'free tuition' Universities of the Country, run by the Brazilian Ministry of Education, were pleased to host this 16th meeting, the first one in Latin America. Mario E G Valerio Conference Chair Robert A Jackson Programme Chair Conference Scope Scope of the Conference was the presentation of the latest investigations on point and extended defects in bulk materials and thin films. Technological applications will be presented alongside fundamental measurements and theories. The main scientific areas included: 1 Fundamental physical phenomena Point and extended defects in wide band-gap systems: oxides, fluorides, nitrides, alkali- and silver-halides, perovskites, minerals, ceramics, nano-structures, organic molecular crystals, glasses, high-k and low-k materials, photonic crystals. 2 Defects at surfaces and interfaces Thin films and low-dimensional systems. Colloids, nano-crystals, and aggregates. Defects and material preparation technology. Defects modelling and computational methods. Radiation effects, radiation induced defects, colour centres. Luminescence of excitons, impurities, and defects. Electronic excitations, excited state dynamics, radiative and non-radiative relaxations. Scintillation, energy transfer and storage, carrier trapping phenomena. Non-linear optical phenomena. Laser active centres. Phonons and defects, electron-phonon interactions. Defect diffusion, ionic relaxations, ionic transport. 3 Technological applications Radiologic imaging and detection, scintillators, and dosimeters. Optical devices and photonics, photorefractive electro-optics, optical fibres, lasers. Materials for micro-electronics. Solid electrolytes, fuel cells, electrochemical sensors, fast ionic conductors. Conference chairpersons: Mário E G Valerio (Conference Chairman), Physics Department, Federal University of Sergipe, SE, Brasil Robert A Jackson (Programme Chairman), School of Physical and Geographical Sciences, Keele University, Keele, UK Conference committees: International Advisory Committee R Capelletti, Italy A V Chadwick, UK J Corish, Ireland J D Comins, South Africa H W den Hartog, The Netherlands K Funke, Germany Robert A Jackson, UK O Kanert, Germany A A Kaplyanskii, Russia A Lushchik, Estonia F Lüty, USA M Moreno, Spain P E Ngoepe, South Africa M Nikl, Czech Republic S V Nistor, Romania Ch Pedrini, France O F Schirmer, Germany J-M Spaeth, Germany A M Stoneham, UK M Suszynska, Poland I Tale, Latvia M E G Valerio, Brasil R T Williams, USA Programme Committee Robert A Jackson (Chair), University of Keele, UK R M Montereali, ENEA C.R. Frascati, Rome, Italy M Moreno, University of Cantabria, Spain Ch Pedrini, University Lyon, France Klaus W H Krambrock, UFMG, MG, Brasil Volkmar Dierolf, Lehigh University, USA Laszlo Kovács, Hungarian Academy of Sciences, Hungary M E G Valerio, UFS, SE, Brasil Local Organizing Committee M E G Valerio, UFS, SE, Brasil Sonia L Baldochi, IPEN, SP, Brasil Klaus W H Krambrock, UFMG, MG, Brasil Livio Amaral, UFRGS, RS, Brasil Ana R Blak, USP, SP, Brasil Marco Cremona, PUC-RJ, RJ, Brasil Anderson S L Gomes, UFPE, PE, Brasil Spero Penha Morato, LaserTools, SP, Brasil Alejandro Ayala, UFC, CE, Brasil ICDIM2008 Sponsors: Sponsors

An overview of the current technology relevant to the design and development of the Space Transportation Main Engine (STME)

NASA Technical Reports Server (NTRS)

Das, Digendra K.

1991-01-01

The objective of this project was to review the latest literature relevant to the Space Transportation Main Engine (STME). The search was focused on the following engine components: (1) gas generator; (2) hydrostatic/fluid bearings; (3) seals/clearances; (4) heat exchanges; (5) nozzles; (6) nozzle/main combustion chamber joint; (7) main injector face plate; and (8) rocket engine.

[Treatment of inflammatory complications of colic diverticular disease at the emergency surgical care hospital].

PubMed

Reznitsky, P A; Yartsev, P A; Shavrina, N V

To assess an effectiveness of minimally invasive and laparoscopic technologies in treatment of inflammatory complications of colic diverticular disease. The study included 150 patients who were divided into control and main groups. Survey included ultrasound, X-ray examination and abdominal computerized tomography. In the main group standardized treatment algorithm including minimally invasive and laparoscopic technologies was used. In the main group 79 patients underwent conservative treatment, minimally invasive (ultrasound-assisted percutaneous drainage of abscesses) and laparoscopic surgery that was successful in 78 (98.7%) patients. Standardized algorithm reduces time of treatment, incidence of postoperative complications, mortality and the risk of recurrent inflammatory complications of colic diverticular disease. Also postoperative quality of life was improved.

SUMMARY REPORT: SMALL COMMUNITY WATER AND WASTE- WATER TREATMENT

EPA Science Inventory

This summary report presents information on the unique needs of small communities facing new water and wastewater treatment requirements. t contains three main sections: technology overviews (each presents a process description, O&M requirements, technology limitations, and finan...

[Industry of traditional Chinese patent medicine science and technology development and review].

PubMed

Lu, Jianwei; Wang, Fang; Yan, Dongmei; Luo, Yun; Yang, Ming

2012-01-01

"Fifteen" since, our country Chinese traditional medicine industry science and technology has made remarkable achievements. In this paper, the development of science and technology policy, Chinese medicine industry, platform construction and other aspects were analyzed, showing 10 years of Chinese traditional medicine industry development of science and technology innovation achievement and development, and on the current development of traditional Chinese medicine industry facing the main tasks and guarantee measures are analyzed.

From Research to Flight: Thinking About Implementation While Performing Fundamental Research

NASA Technical Reports Server (NTRS)

Johnson, Les

2010-01-01

This slide presentation calls for a strategy to implement new technologies. Such a strategy would allow advanced space transportation technologies to mature for exploration beyond Earth orbit. It discusses the difference between technology push versus technology pull. It also reviews the three basic technology readiness levels (TRL). The presentation traces examples of technology development to flight application: the Space Shuttle Main Engine Advanced Health Management System, the Friction Stir Welding technology the (auto-adjustable pin tool). A couple of technologies currently not in flight, but are being reviewed for potential use are: cryogenic fluid management (CFM), and solar sail propulsion. There is also an attempt to explain why new technologies are so difficult to field.

Cognitive-Behavioral Therapy.

PubMed

An, Hong; He, Ri-Hui; Zheng, Yun-Rong; Tao, Ran

2017-01-01

Cognitive-behavioral therapy (CBT) is the main method of psychotherapy generally accepted in the field of substance addiction and non-substance addiction. This chapter mainly introduces the methods and technology of cognitive-behavior therapy of substance addiction, especially in order to prevent relapse. In the cognitive-behavior treatment of non-substance addiction, this chapter mainly introduces gambling addiction and food addiction.

Advances in traction drive technology

NASA Technical Reports Server (NTRS)

Loewenthal, S. H.; Anderson, N. E.; Rohn, D. A.

1983-01-01

Traction drives are traced from early uses as main transmissions in automobiles at the turn of the century to modern, high-powered traction drives capable of transmitting hundreds of horsepower. Recent advances in technology are described which enable today's traction drive to be a serious candidate for off-highway vehicles and helicopter applications. Improvements in materials, traction fluids, design techniques, power loss and life prediction methods will be highlighted. Performance characteristics of the Nasvytis fixed-ratio drive are given. Promising future drive applications, such as helicopter main transmissions and servo-control positioning mechanisms are also addressed.

The key quality control technology of main cable erection in long-span suspension bridge construction

NASA Astrophysics Data System (ADS)

Chen, Yongrui; Wei, Wei; Dai, Jie

2017-04-01

Main cable is one of the most important structure of suspension Bridges, which bear all the dead and live load from upper structure. Cable erection is one of the most critical process in suspension bridge construction. Key points about strand erection are studied in this paper, including strand traction, lateral movement, section adjustment, placing into saddle, anchoring, line shape adjustment and keeping, and tension control. The technology has helped a long-span suspension bridge in Yunnan Province, China get a ideal finished state.

Technical and Sociological Approaches for Curriculum Innovation on Clothing Education Department

NASA Astrophysics Data System (ADS)

Tristantie, N.

2018-02-01

Education in the context of social and technical development is defined as the main factor in the learning process which is implied into curriculum. It needs to be anticipated responsively how the goals of Clothing Education Department should be achieved. The sociological and technological through curriculum innovation at Clothing Education Department aims to gain good profile of the professional graduates in the future. By using the literature study, it is found out that sociological development and technological approach are the main foundation for sustainability of Clothing Education Department.

Present status and trends of image fusion

NASA Astrophysics Data System (ADS)

Xiang, Dachao; Fu, Sheng; Cai, Yiheng

2009-10-01

Image fusion information extracted from multiple images which is more accurate and reliable than that from just a single image. Since various images contain different information aspects of the measured parts, and comprehensive information can be obtained by integrating them together. Image fusion is a main branch of the application of data fusion technology. At present, it was widely used in computer vision technology, remote sensing, robot vision, medical image processing and military field. This paper mainly presents image fusion's contents, research methods, and the status quo at home and abroad, and analyzes the development trend.

NASA Systems Autonomy Demonstration Program - A step toward Space Station automation

NASA Technical Reports Server (NTRS)

Starks, S. A.; Rundus, D.; Erickson, W. K.; Healey, K. J.

1987-01-01

This paper addresses a multiyear NASA program, the Systems Autonomy Demonstration Program (SADP), whose main objectives include the development, integration, and demonstration of automation technology in Space Station flight and ground support systems. The role of automation in the Space Station is reviewed, and the main players in SADP and their roles are described. The core research and technology being promoted by SADP are discussed, and a planned 1988 milestone demonstration of the automated monitoring, operation, and control of a complete mission operations subsystem is addressed.

Designing human centered GeoVisualization application--the SanaViz--for telehealth users: a case study.

PubMed

Joshi, Ashish; de Araujo Novaes, Magdala; Machiavelli, Josiane; Iyengar, Sriram; Vogler, Robert; Johnson, Craig; Zhang, Jiajie; Hsu, Chiehwen E

2012-01-01

Public health data is typically organized by geospatial unit. GeoVisualization (GeoVis) allows users to see information visually on a map. Examine telehealth users' perceptions towards existing public health GeoVis applications and obtains users' feedback about features important for the design and development of Human Centered GeoVis application "the SanaViz". We employed a cross sectional study design using mixed methods approach for this pilot study. Twenty users involved with the NUTES telehealth center at Federal University of Pernambuco (UFPE), Recife, Brazil were enrolled. Open and closed ended questionnaires were used to gather data. We performed audio recording for the interviews. Information gathered included socio-demographics, prior spatial skills and perception towards use of GeoVis to evaluate telehealth services. Card sorting and sketching methods were employed. Univariate analysis was performed for the continuous and categorical variables. Qualitative analysis was performed for open ended questions. Existing Public Health GeoVis applications were difficult to use. Results found interaction features zooming, linking and brushing and representation features Google maps, tables and bar chart as most preferred GeoVis features. Early involvement of users is essential to identify features necessary to be part of the human centered GeoVis application "the SanaViz".

Particulate Emissions from a Stationary Engine Fueled with Ultra-Low-Sulfur Diesel and Waste-Cooking-Oil-Derived Biodiesel.

PubMed

Betha, Raghu; Balasubramanian, Rajasekhar

2011-10-01

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture. [Box: see text].

Particulate emissions from a stationary engine fueled with ultra-low-sulfur diesel and waste-cooking-oil-derived biodiesel.

PubMed

Betha, Raghu; Balasubramanian, Rajasekhar

2011-10-01

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture.

Inhaled Pollutants: The Molecular Scene behind Respiratory and Systemic Diseases Associated with Ultrafine Particulate Matter

PubMed Central

Traboulsi, Hussein; Guerrina, Necola; Iu, Matthew; Maysinger, Dusica; Ariya, Parisa; Baglole, Carolyn J.

2017-01-01

Air pollution of anthropogenic origin is largely from the combustion of biomass (e.g., wood), fossil fuels (e.g., cars and trucks), incinerators, landfills, agricultural activities and tobacco smoke. Air pollution is a complex mixture that varies in space and time, and contains hundreds of compounds including volatile organic compounds (e.g., benzene), metals, sulphur and nitrogen oxides, ozone and particulate matter (PM). PM0.1 (ultrafine particles (UFP)), those particles with a diameter less than 100 nm (includes nanoparticles (NP)) are considered especially dangerous to human health and may contribute significantly to the development of numerous respiratory and cardiovascular diseases such as chronic obstructive pulmonary disease (COPD) and atherosclerosis. Some of the pathogenic mechanisms through which PM0.1 may contribute to chronic disease is their ability to induce inflammation, oxidative stress and cell death by molecular mechanisms that include transcription factors such as nuclear factor κB (NF-κB) and nuclear factor (erythroid-derived 2)-like 2 (Nrf2). Epigenetic mechanisms including non-coding RNA (ncRNA) may also contribute towards the development of chronic disease associated with exposure to PM0.1. This paper highlights emerging molecular concepts associated with inhalational exposure to PM0.1 and their ability to contribute to chronic respiratory and systemic disease. PMID:28125025

The Comparison of Personalization Recommendation for E-Commerce

NASA Astrophysics Data System (ADS)

Ya, Luo

Personalization recommendation is the key technology in E-commerce, which affects the performance of E-commerce system. This paper mainly introduces personalization recommendation system and its role, and several widely used recommendation technology. Through comparing and analyzing on the strengths and weaknesses of recommendation technology, it concludes that the combined application for a variety of techniques should satisfy the actual needs better.

Report of a Planning Conference for Solar Technology Information Transfer in Kentucky (Frankfort, September 11-12, 1978).

ERIC Educational Resources Information Center

Capps, Randall, Ed.

This summary of the deliberations of the Planning Conference for Solar Technology Information Transfer includes an outline of a functioning solar energy technology network for the State of Kentucky and a set of recommendations for future action. Four main types of information agents were identified: (1) the State Library System; (2) the State…

The application demand analysis of advanced photoelectric technology in the future unmanned vehicle loads

NASA Astrophysics Data System (ADS)

Zhang, Lei; Cao, Wei; Li, Shengcai; Lu, Peng

2018-01-01

Introduced some unmanned vehicles development present situation, points out that the main development trend of photoelectric technology, analyzes the basic ability requirement of unmanned vehicles, in the future war system demonstrates the photoelectric information transmission, battlefield situational awareness, photoelectric integrated optoelectronic technology such as against the application of the unmanned vehicles demand in the future.

Technology and College Students: What Faculty Members Think about the Use of Technology in Higher Education

ERIC Educational Resources Information Center

Islim, Omer Faruk; Sevim Cirak, Nese

2017-01-01

Tablet PCs especially iPads are one of the most commonly used devices that most educational institutions from elementary school to colleges have been using as a main or supplementary part of their educational system. This article aims at investigating faculty members' personal and educational use of technology especially iPads, their opinions on…

The Effect of Technology on Students' Opinions about Authentic Learning Activities in Science Courses

ERIC Educational Resources Information Center

Coskun, Hilal; Dogan, Alev; Uluay, Gulsah

2017-01-01

Today, most of the researchers have agreed on the importance of classroom environment where students responsible of their own learning. It is important to use modern learning methods with technology to reach this aim in courses. The main purpose of this study is to investigate the effect of using Technology in science courses to investigate 7th…

Values, Choices, Responsibilities: Thinking beyond the Scholarly Place of Ethics for the GIScience and Technology Profession and GIScience

ERIC Educational Resources Information Center

Harvey, Francis

2014-01-01

To help ethical issues gain traction in geographic information technology education, this article proposes that the education of GIScience and technology professionals go beyond abstract scholarly ethics to applied approaches based on practical wisdom. The main point for educators made in this paper is that applied ethics' focus on values,…

A Comparative Analysis of Spatial Visualization Ability and Drafting Models for Industrial and Technology Education Students

ERIC Educational Resources Information Center

Katsioloudis, Petros; Jovanovic, Vukica; Jones, Mildred

2014-01-01

The main purpose of this study was to determine significant positive effects among the use of three different types of drafting models, and to identify whether any differences exist towards promotion of spatial visualization ability for students in Industrial Technology and Technology Education courses. In particular, the study compared the use of…

Policy, Practice, and Reality: Exploring a Nation-Wide Technology Implementation in Turkish Schools

ERIC Educational Resources Information Center

Akcaoglu, Mete; Gumus, Sedat; Bellibas, Mehmet Sukru; Boyer, D. Matthew

2015-01-01

Technology has already become an indispensable part of our lives, and nations around the world see schools as the main agents to prepare their youth for a technology-filled future, and invest important amounts of funding to provide hardware to schools, students and teachers. The Turkish Ministry of National Education is in the midst of the FATIH…

Enhancing mung bean hydration using the ultrasound technology: description of mechanisms and impact on its germination and main components

NASA Astrophysics Data System (ADS)

Miano, Alberto Claudio; Pereira, Jessica Da Costa; Castanha, Nanci; Júnior, Manoel Divino Da Matta; Augusto, Pedro Esteves Duarte

2016-12-01

The ultrasound technology was successfully used to improve the mass transfer processes on food. However, the study of this technology on the grain hydration and on its main components properties was still not appropriately described. This work studied the application of the ultrasound technology on the hydration process of mung beans (Vigna radiata). This grain showed sigmoidal hydration behavior with a specific water entrance pathway. The ultrasound reduced ~25% of the hydration process time. In addition, this technology caused acceleration of the seed germination - and some hypothesis for this enhancement were proposed. Moreover, it was demonstrated that the ultrasound did not change both structure and pasting properties of the bean starch. Finally, the flour rheological properties proved that the ultrasound increased its apparent viscosity, and as the starch was not modified, this alteration was attributed to the proteins. All these results are very desirable for industry since the ultrasound technology improves the hydration process without altering the starch properties, accelerates the germination process (that is important for the malting and sprouting process) and increases the flour apparent viscosity, which is desirable to produce bean-based products that need higher consistency.

Technology Enhanced Learning in Programming Courses--International Perspective

ERIC Educational Resources Information Center

Ivanovic, Mirjana; Xinogalos, Stelios; Pitner, Tomáš; Savic, Miloš

2017-01-01

Technology enhanced learning (TEL) is increasingly influencing university education, mainly in overcoming disadvantages of direct instruction teaching approaches, and encouraging creativity, problem solving and critical thinking in student-centered, interactive learning environments. In this paper, experiences from object-oriented programming…

Rehabilitation Technologies for Water Mains

EPA Science Inventory

This paper presents on-going research work for the USEPA Research Project on “Rehabilitation of Water and Wastewater Systems.” It will compare various renewal methods (i.e. replacement, rehabilitation and repair technologies that are available in the market). The paper discusse...

Raman chemical imaging technology for food and agricultural applications

USDA-ARS?s Scientific Manuscript database

This paper presents Raman chemical imaging technology for inspecting food and agricultural products. The paper puts emphasis on introducing and demonstrating Raman imaging techniques for practical uses in food analysis. The main topics include Raman scattering principles, Raman spectroscopy measurem...

78 FR 47531 - Airworthiness Directives; Various Restricted Category Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... Technology, Inc.; Hagglund Helicopters, LLC (previously Western International Aviation, Inc.); International.... This AD requires creating a component history card or equivalent record for each main rotor grip (grip....); California Department of Forestry; Garlick Helicopters, Inc.; Global Helicopter Technology, Inc.; Hagglund...

WEB-BASED DATABASE ON RENEWAL TECHNOLOGIES ...

EPA Pesticide Factsheets

As U.S. utilities continue to shore up their aging infrastructure, renewal needs now represent over 43% of annual expenditures compared to new construction for drinking water distribution and wastewater collection systems (Underground Construction [UC], 2016). An increased understanding of renewal options will ultimately assist drinking water utilities in reducing water loss and help wastewater utilities to address infiltration and inflow issues in a cost-effective manner. It will also help to extend the service lives of both drinking water and wastewater mains. This research effort involved collecting case studies on the use of various trenchless pipeline renewal methods and providing the information in an online searchable database. The overall objective was to further support technology transfer and information sharing regarding emerging and innovative renewal technologies for water and wastewater mains. The result of this research is a Web-based, searchable database that utility personnel can use to obtain technology performance and cost data, as well as case study references. The renewal case studies include: technologies used; the conditions under which the technology was implemented; costs; lessons learned; and utility contact information. The online database also features a data mining tool for automated review of the technologies selected and cost data. Based on a review of the case study results and industry data, several findings are presented on tren