Microcantilever sensor platform for UGV-based detection

NASA Astrophysics Data System (ADS)

Lawrence, Tyson T.; Halleck, A. E.; Schuler, Peter S.; Mahmud, K. K.; Hicks, David R.

2010-04-01

The increased use of Unmanned Ground Vehicles (UGVs) drives the need for new lightweight, low cost sensors. Microelectromechanical System (MEMS) based microcantilever sensors are a promising technology to meet this need, because they can be manufactured at low cost on a mass scale, and are easily integrated into a UGV platform for detection of explosives and other threat agents. While the technology is extremely sensitive, selectivity is a major challenge and the response modes are not well understood. This work summarizes advances in characterizing ultrasensitive microcantilever responses, sampling considerations, and sensor design and cantilever coating methodologies consistent with UGV point detector needs.

New distributed radar technology based on UAV or UGV application

NASA Astrophysics Data System (ADS)

Molchanov, Pavlo A.; Contarino, Vincent M.

2013-05-01

Regular micro and nano radars cannot provide reliable tracking of low altitude low profile aerial targets in urban and mountain areas because of reflection and re-reflections from buildings and terrain. They become visible and vulnerable to guided missiles if positioned on a tower or blimp. Doppler radar cannot distinguish moving cars and small low altitude aerial targets in an urban area. A new concept of pocket size distributed radar technology based on the application of UAV (Unmanned Air Vehicles), UGV (Unmanned Ground Vehicles) is proposed for tracking of low altitude low profile aerial targets at short and medium distances for protection of stadium, camp, military facility in urban or mountain areas.

Landmark-Based Navigation of an Unmanned Ground Vehicle (UGV)

DTIC Science & Technology

2009-03-01

against large measurement errors. 20090710280 RELEASE LIMITATION Approved for public release 4p fv^-Jo-osiit? Published by Weapons Systems Division...achieved as numerous low cost gyroscopes in the market meet this requirement. 24 DSTO-TR-2260 3.5.4 Sensitivity to Vehicle Speed In this subsection

Unmanned Ground Vehicle Perception Using Thermal Infrared Cameras

NASA Technical Reports Server (NTRS)

Rankin, Arturo; Huertas, Andres; Matthies, Larry; Bajracharya, Max; Assad, Christopher; Brennan, Shane; Bellutta, Paolo; Sherwin, Gary W.

2011-01-01

The ability to perform off-road autonomous navigation at any time of day or night is a requirement for some unmanned ground vehicle (UGV) programs. Because there are times when it is desirable for military UGVs to operate without emitting strong, detectable electromagnetic signals, a passive only terrain perception mode of operation is also often a requirement. Thermal infrared (TIR) cameras can be used to provide day and night passive terrain perception. TIR cameras have a detector sensitive to either mid-wave infrared (MWIR) radiation (3-5?m) or long-wave infrared (LWIR) radiation (8-12?m). With the recent emergence of high-quality uncooled LWIR cameras, TIR cameras have become viable passive perception options for some UGV programs. The Jet Propulsion Laboratory (JPL) has used a stereo pair of TIR cameras under several UGV programs to perform stereo ranging, terrain mapping, tree-trunk detection, pedestrian detection, negative obstacle detection, and water detection based on object reflections. In addition, we have evaluated stereo range data at a variety of UGV speeds, evaluated dual-band TIR classification of soil, vegetation, and rock terrain types, analyzed 24 hour water and 12 hour mud TIR imagery, and analyzed TIR imagery for hazard detection through smoke. Since TIR cameras do not currently provide the resolution available from megapixel color cameras, a UGV's daytime safe speed is often reduced when using TIR instead of color cameras. In this paper, we summarize the UGV terrain perception work JPL has performed with TIR cameras over the last decade and describe a calibration target developed by General Dynamics Robotic Systems (GDRS) for TIR cameras and other sensors.

Investigating the Usefulness of Operator Aids for Autonomous Unmanned Ground Vehicles Performing Reconnaissance Tasks

DTIC Science & Technology

2013-09-01

generated using data from the ANS about the path that the automation attempted to follow. The STP operator aid was displayed as a translucent green...intended route of the UGV projected for the next several seconds. Similarly, the LTP operator aid was displayed as a translucent blue line overlaid on...route of the UGV projected for the next several minutes or more. The combination of STP and LTP operator aids simply displayed both translucent green

Toward a generic UGV autopilot

NASA Astrophysics Data System (ADS)

Moore, Kevin L.; Whitehorn, Mark; Weinstein, Alejandro J.; Xia, Junjun

2009-05-01

Much of the success of small unmanned air vehicles (UAVs) has arguably been due to the widespread availability of low-cost, portable autopilots. While the development of unmanned ground vehicles (UGVs) has led to significant achievements, as typified by recent grand challenge events, to date the UGV equivalent of the UAV autopilot is not available. In this paper we describe our recent research aimed at the development of a generic UGV autopilot. Assuming we are given a drive-by-wire vehicle that accepts as inputs steering, brake, and throttle commands, we present a system that adds sonar ranging sensors, GPS/IMU/odometry, stereo camera, and scanning laser sensors, together with a variety of interfacing and communication hardware. The system also includes a finite state machine-based software architecture as well as a graphical user interface for the operator control unit (OCU). Algorithms are presented that enable an end-to-end scenario whereby an operator can view stereo images as seen by the vehicle and can input GPS waypoints either from a map or in the vehicle's scene-view image, at which point the system uses the environmental sensors as inputs to a Kalman filter for pose estimation and then computes control actions to move through the waypoint list, while avoiding obstacles. The long-term goal of the research is a system that is generically applicable to any drive-by-wire unmanned ground vehicle.

Absolute High-Precision Localisation of an Unmanned Ground Vehicle by Using Real-Time Aerial Video Imagery for Geo-referenced Orthophoto Registration

NASA Astrophysics Data System (ADS)

Kuhnert, Lars; Ax, Markus; Langer, Matthias; Nguyen van, Duong; Kuhnert, Klaus-Dieter

This paper describes an absolute localisation method for an unmanned ground vehicle (UGV) if GPS is unavailable for the vehicle. The basic idea is to combine an unmanned aerial vehicle (UAV) to the ground vehicle and use it as an external sensor platform to achieve an absolute localisation of the robotic team. Beside the discussion of the rather naive method directly using the GPS position of the aerial robot to deduce the ground robot's position the main focus of this paper lies on the indirect usage of the telemetry data of the aerial robot combined with live video images of an onboard camera to realise a registration of local video images with apriori registered orthophotos. This yields to a precise driftless absolute localisation of the unmanned ground vehicle. Experiments with our robotic team (AMOR and PSYCHE) successfully verify this approach.

Robotic acquisition programs: technical and performance challenges

NASA Astrophysics Data System (ADS)

Thibadoux, Steven A.

2002-07-01

The Unmanned Ground Vehicles/ Systems Joint Project Office (UGV/S JPO) is developing and fielding a variety of tactical robotic systems for the Army and Marine Corps. The Standardized Robotic System (SRS) provides a family of common components that can be installed in existing military vehicles, to allow unmanned operation of the vehicle and its payloads. The Robotic Combat Support System (RCSS) will be a medium sized unmanned system with interchangeable attachments, allowing a remote operator to perform a variety of engineering tasks. The Gladiator Program is a USMC initiative for a small to medium sized, highly mobile UGV to conduct scout/ surveillance missions and to carry various lethal and non-lethal payloads. Acquisition plans for these programs require preplanned evolutionary block upgrades to add operational capability, as new technology becomes available. This paper discusses technical and performance issues that must be resolved and the enabling technologies needed for near term block upgrades of these first generation robotic systems. Additionally, two Joint Robotics Program (JRP) initiatives, Robotic Acquisition through Virtual Environments and Networked Simulations (RAVENS) and Joint Architecture for Unmanned Ground Systems (JAUGS), will be discussed. RAVENS and JAUGS will be used to efficiently evaluate and integrate new technologies to be incorporated in system upgrades.

Developing UGVs for the FCS program

NASA Astrophysics Data System (ADS)

Kamsickas, Gary M.; Ward, John N.

2003-09-01

The FCS Operational Requirements Document (ORD) identifies unmanned systems as a key component of the FCS Unit of Action. FCS unmanned systems include Unmanned Aerial Vehicles (UAV), Unmanned Ground Vehicles (UGV), Unattended Ground Sensors (UGS) and Unattended Munitions (UM). Unmanned systems are intended to enhance the Unit of Action across the full range of operations when integrated with manned platforms. Unmanned systems will provide the commander with tools to gather battlespace information while significantly reducing overall soldier risk. Unmanned systems will be used in some cases to augment or replace human intervention to perform many of the dirty, dull and dangerous missions presently performed by soldiers and to serve as a combat multiplier for mission performance, force protection and survivability. This paper focuses on the application of UGVs within the FCS Unit of Action. There are three different UGVs planned to support the FCS Unit of Action; the Soldier Unmanned Ground Vehicle (SUGV); The Multi-role Utility Logistics Equipment (MULE) platform; and the Armed Robotic Vehicle (ARV).

Semi-autonomous unmanned ground vehicle control system

NASA Astrophysics Data System (ADS)

Anderson, Jonathan; Lee, Dah-Jye; Schoenberger, Robert; Wei, Zhaoyi; Archibald, James

2006-05-01

Unmanned Ground Vehicles (UGVs) have advantages over people in a number of different applications, ranging from sentry duty, scouting hazardous areas, convoying goods and supplies over long distances, and exploring caves and tunnels. Despite recent advances in electronics, vision, artificial intelligence, and control technologies, fully autonomous UGVs are still far from being a reality. Currently, most UGVs are fielded using tele-operation with a human in the control loop. Using tele-operations, a user controls the UGV from the relative safety and comfort of a control station and sends commands to the UGV remotely. It is difficult for the user to issue higher level commands such as patrol this corridor or move to this position while avoiding obstacles. As computer vision algorithms are implemented in hardware, the UGV can easily become partially autonomous. As Field Programmable Gate Arrays (FPGAs) become larger and more powerful, vision algorithms can run at frame rate. With the rapid development of CMOS imagers for consumer electronics, frame rate can reach as high as 200 frames per second with a small size of the region of interest. This increase in the speed of vision algorithm processing allows the UGVs to become more autonomous, as they are able to recognize and avoid obstacles in their path, track targets, or move to a recognized area. The user is able to focus on giving broad supervisory commands and goals to the UGVs, allowing the user to control multiple UGVs at once while still maintaining the convenience of working from a central base station. In this paper, we will describe a novel control system for the control of semi-autonomous UGVs. This control system combines a user interface similar to a simple tele-operation station along with a control package, including the FPGA and multiple cameras. The control package interfaces with the UGV and provides the necessary control to guide the UGV.

Multisensor Equipped Uav/ugv for Automated Exploration

NASA Astrophysics Data System (ADS)

Batzdorfer, S.; Bobbe, M.; Becker, M.; Harms, H.; Bestmann, U.

2017-08-01

The usage of unmanned systems for exploring disaster scenarios has become more and more important in recent times as a supporting system for action forces. These systems have to offer a well-balanced relationship between the quality of support and additional workload. Therefore within the joint research project ANKommEn - german acronym for Automated Navigation and Communication for Exploration - a system for exploration of disaster scenarios is build-up using multiple UAV und UGV controlled via a central ground station. The ground station serves as user interface for defining missions and tasks conducted by the unmanned systems, equipped with different environmental sensors like cameras - RGB as well as IR - or LiDAR. Depending on the exploration task results, in form of pictures, 2D stitched orthophoto or LiDAR point clouds will be transmitted via datalinks and displayed online at the ground station or will be processed in short-term after a mission, e.g. 3D photogrammetry. For mission planning and its execution, UAV/UGV monitoring and georeferencing of environmental sensor data, reliable positioning and attitude information is required. This is gathered using an integrated GNSS/IMU positioning system. In order to increase availability of positioning information in GNSS challenging scenarios, a GNSS-Multiconstellation based approach is used, amongst others. The present paper focuses on the overall system design including the ground station and sensor setups on the UAVs and UGVs, the underlying positioning techniques as well as 2D and 3D exploration based on a RGB camera mounted on board the UAV and its evaluation based on real world field tests.

Daytime Water Detection Based on Sky Reflections

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Matthies, Larry H.; Bellutta, Paolo

2011-01-01

Robust water detection is a critical perception requirement for unmanned ground vehicle (UGV) autonomous navigation. This is particularly true in wide-open areas where water can collect in naturally occurring terrain depressions during periods of heavy precipitation and form large water bodies. One of the properties of water useful for detecting it is that its surface acts as a horizontal mirror at large incidence angles. Water bodies can be indirectly detected by detecting reflections of the sky below the horizon in color imagery. The Jet Propulsion Laboratory (JPL) has implemented a water detector based on sky reflections that geometrically locates the pixel in the sky that is reflecting on a candidate water pixel on the ground and predicts if the ground pixel is water based on color similarity and local terrain features. This software detects water bodies in wide-open areas on cross-country terrain at mid- to far-range using imagery acquired from a forward-looking stereo pair of color cameras mounted on a terrestrial UGV. In three test sequences approaching a pond under a clear, overcast, and cloudy sky, the true positive detection rate was 100% when the UGV was beyond 7 meters of the water's leading edge and the largest false positive detection rate was 0.58%. The sky reflection based water detector has been integrated on an experimental unmanned vehicle and field tested at Ft. Indiantown Gap, PA, USA.

PointCom: semi-autonomous UGV control with intuitive interface

NASA Astrophysics Data System (ADS)

Rohde, Mitchell M.; Perlin, Victor E.; Iagnemma, Karl D.; Lupa, Robert M.; Rohde, Steven M.; Overholt, James; Fiorani, Graham

2008-04-01

Unmanned ground vehicles (UGVs) will play an important role in the nation's next-generation ground force. Advances in sensing, control, and computing have enabled a new generation of technologies that bridge the gap between manual UGV teleoperation and full autonomy. In this paper, we present current research on a unique command and control system for UGVs named PointCom (Point-and-Go Command). PointCom is a semi-autonomous command system for one or multiple UGVs. The system, when complete, will be easy to operate and will enable significant reduction in operator workload by utilizing an intuitive image-based control framework for UGV navigation and allowing a single operator to command multiple UGVs. The project leverages new image processing algorithms for monocular visual servoing and odometry to yield a unique, high-performance fused navigation system. Human Computer Interface (HCI) techniques from the entertainment software industry are being used to develop video-game style interfaces that require little training and build upon the navigation capabilities. By combining an advanced navigation system with an intuitive interface, a semi-autonomous control and navigation system is being created that is robust, user friendly, and less burdensome than many current generation systems. mand).

Towards Commanding Unmanned Ground Vehicle Movement in Unfamiliar Environments Using Unconstrained English: Initial Research Results

DTIC Science & Technology

2007-06-01

constrained list of command words could be valuable in many systems, as would the ability of driverless vehicles to navigate through a route...Sensemaking in UGVs • Future Combat Systems UGV roles – Driverless trucks – Robotic mules (soldier, squad aid) – Intelligent munitions – And more! • Some

UGV navigation in wireless sensor and actuator network environments

NASA Astrophysics Data System (ADS)

Zhang, Guyu; Li, Jianfeng; Duncan, Christian A.; Kanno, Jinko; Selmic, Rastko R.

2012-06-01

We consider a navigation problem in a distributed, self-organized and coordinate-free Wireless Sensor and Ac- tuator Network (WSAN). We rst present navigation algorithms that are veried using simulation results. Con- sidering more than one destination and multiple mobile Unmanned Ground Vehicles (UGVs), we introduce a distributed solution to the Multi-UGV, Multi-Destination navigation problem. The objective of the solution to this problem is to eciently allocate UGVs to dierent destinations and carry out navigation in the network en- vironment that minimizes total travel distance. The main contribution of this paper is to develop a solution that does not attempt to localize either the UGVs or the sensor and actuator nodes. Other than some connectivity as- sumptions about the communication graph, we consider that no prior information about the WSAN is available. The solution presented here is distributed, and the UGV navigation is solely based on feedback from neigh- boring sensor and actuator nodes. One special case discussed in the paper, the Single-UGV, Multi-Destination navigation problem, is essentially equivalent to the well-known and dicult Traveling Salesman Problem (TSP). Simulation results are presented that illustrate the navigation distance traveled through the network. We also introduce an experimental testbed for the realization of coordinate-free and localization-free UGV navigation. We use the Cricket platform as the sensor and actuator network and a Pioneer 3-DX robot as the UGV. The experiments illustrate the UGV navigation in a coordinate-free WSAN environment where the UGV successfully arrives at the assigned destinations.

Modeling Human Steering Behavior During Path Following in Teleoperation of Unmanned Ground Vehicles.

PubMed

Mirinejad, Hossein; Jayakumar, Paramsothy; Ersal, Tulga

2018-04-01

This paper presents a behavioral model representing the human steering performance in teleoperated unmanned ground vehicles (UGVs). Human steering performance in teleoperation is considerably different from the performance in regular onboard driving situations due to significant communication delays in teleoperation systems and limited information human teleoperators receive from the vehicle sensory system. Mathematical models capturing the teleoperation performance are a key to making the development and evaluation of teleoperated UGV technologies fully simulation based and thus more rapid and cost-effective. However, driver models developed for the typical onboard driving case do not readily address this need. To fill the gap, this paper adopts a cognitive model that was originally developed for a typical highway driving scenario and develops a tuning strategy that adjusts the model parameters in the absence of human data to reflect the effect of various latencies and UGV speeds on driver performance in a teleoperated path-following task. Based on data collected from a human subject test study, it is shown that the tuned model can predict both the trend of changes in driver performance for different driving conditions and the best steering performance of human subjects in all driving conditions considered. The proposed model with the tuning strategy has a satisfactory performance in predicting human steering behavior in the task of teleoperated path following of UGVs. The established model is a suited candidate to be used in place of human drivers for simulation-based studies of UGV mobility in teleoperation systems.

CAT/RF Simulation Lessons Learned

DTIC Science & Technology

2003-06-11

IVSS-2003-MAS-7 CAT /RF Simulation Lessons Learned Christopher Mocnik Vetronics Technology Area, RDECOM TARDEC Tim Lee DCS Corporation...developed a re- configurable Unmanned Ground Vehicle (UGV) simulation for the Crew integration and Automation Test bed ( CAT ) and Robotics Follower (RF...Advanced Technology Demonstration (ATD) experiments. This simulation was developed as a component of the Embedded Simulation System (ESS) of the CAT

Sensor deployment on unmanned ground vehicles

NASA Astrophysics Data System (ADS)

Gerhart, Grant R.; Witus, Gary

2007-10-01

TARDEC has been developing payloads for small robots as part of its unmanned ground vehicle (UGV) development programs. These platforms typically weigh less than 100 lbs and are used for various physical security and force protection applications. This paper will address a number of technical issues including platform mobility, payload positioning, sensor configuration and operational tradeoffs. TARDEC has developed a number of robots with different mobility mechanisms including track, wheel and hybrid track/wheel running gear configurations. An extensive discussion will focus upon omni-directional vehicle (ODV) platforms with enhanced intrinsic mobility for positioning sensor payloads. This paper also discusses tradeoffs between intrinsic platform mobility and articulated arm complexity for end point positioning of modular sensor packages.

A Surveillance and Targeting System for an Unmanned Ground Vehicle

DTIC Science & Technology

1990-08-01

CHARACTERISTICS - SELECTABLE INFRASONIC AND ULTRASONIC FREQUENCY SHIFTING CAPABILITY - SUPER-BINAURAL CONFIGURATION ANGLE AND PICKUP SEPARATION GREATER THAN...HUMAN HEAD - VARIABLE GAIN WITH CLIPPING - INTEGRATABLE INTO TOV OPERATOR HELMET - CONTROL INTERFACE: VOLUME UP/DOWN, SONIC ON/OFF, ULTRA ON/OFF... INFRA ON/OFF, BOOST HI/MED/OFF ----- UGV/TOV ----- ---- AUVS/DAYTON ---- LASER SAFETY IMPLICATIONS IMPLICATIONS FOR DESIGN: - POWER UP SEQUENCE - ABORT

Sensor data fusion for automated threat recognition in manned-unmanned infantry platoons

NASA Astrophysics Data System (ADS)

Wildt, J.; Varela, M.; Ulmke, M.; Brüggermann, B.

2017-05-01

To support a dismounted infantry platoon during deployment we team it with several unmanned aerial and ground vehicles (UAV and UGV, respectively). The unmanned systems integrate seamlessly into the infantry platoon, providing automated reconnaissance during movement while keeping formation as well as conducting close range reconnaissance during halt. The sensor data each unmanned system provides is continuously analyzed in real time by specialized algorithms, detecting humans in live videos of UAV mounted infrared cameras as well as gunshot detection and bearing by acoustic sensors. All recognized threats are fused into a consistent situational picture in real time, available to platoon and squad leaders as well as higher level command and control (C2) systems. This gives friendly forces local information superiority and increased situational awareness without the need to constantly monitor the unmanned systems and sensor data.

Unmanned ground vehicles for integrated force protection

NASA Astrophysics Data System (ADS)

Carroll, Daniel M.; Mikell, Kenneth; Denewiler, Thomas

2004-09-01

The combination of Command and Control (C2) systems with Unmanned Ground Vehicles (UGVs) provides Integrated Force Protection from the Robotic Operation Command Center. Autonomous UGVs are directed as Force Projection units. UGV payloads and fixed sensors provide situational awareness while unattended munitions provide a less-than-lethal response capability. Remote resources serve as automated interfaces to legacy physical devices such as manned response vehicles, barrier gates, fence openings, garage doors, and remote power on/off capability for unmanned systems. The Robotic Operations Command Center executes the Multiple Resource Host Architecture (MRHA) to simultaneously control heterogeneous unmanned systems. The MRHA graphically displays video, map, and status for each resource using wireless digital communications for integrated data, video, and audio. Events are prioritized and the user is prompted with audio alerts and text instructions for alarms and warnings. A control hierarchy of missions and duty rosters support autonomous operations. This paper provides an overview of the key technology enablers for Integrated Force Protection with details on a force-on-force scenario to test and demonstrate concept of operations using Unmanned Ground Vehicles. Special attention is given to development and applications for the Remote Detection Challenge and Response (REDCAR) initiative for Integrated Base Defense.

A Near Term Approach to Embedded Training: Battle Command Visualization 101

DTIC Science & Technology

2006-05-01

Example of Task Guidance area at the end of Module 1, Exercise 1 (Level 1) ...... 26 Figure 9 Example of Robo -Scout information, accessed through the...unmanned ground vehicle (UGV) sensor, the Robo -Scout. They will be equipped with both passive and active systems to provide target acquisition, real...PIR# Track of Update RqieTemplated Required 1 Tracked & NAI 1, 2 S, T S200 synthetic L 2 hrs Vehicle type, Intel, Fires (PIR 1) Wheeled aperture radar

Real-Time and High-Fidelity Simulation Environment for Autonomous Ground Vehicle Dynamics

NASA Technical Reports Server (NTRS)

Cameron, Jonathan; Myint, Steven; Kuo, Calvin; Jain, Abhi; Grip, Havard; Jayakumar, Paramsothy; Overholt, Jim

2013-01-01

This paper reports on a collaborative project between U.S. Army TARDEC and Jet Propulsion Laboratory (JPL) to develop a unmanned ground vehicle (UGV) simulation model using the ROAMS vehicle modeling framework. Besides modeling the physical suspension of the vehicle, the sensing and navigation of the HMMWV vehicle are simulated. Using models of urban and off-road environments, the HMMWV simulation was tested in several ways, including navigation in an urban environment with obstacle avoidance and the performance of a lane change maneuver.

Unmanned Ground Vehicle

DTIC Science & Technology

2001-11-01

Systems ( JAUGS ). JAUGS is a JRP technology initiative under the cognizance of the Aviation and Missile Command Research, Development and Engineering Center...AMRDEC). The JAUGS focus is on developing a high-level command and control architecture for UGVs. As defined in the JRP Glossary, “ JAUGS is an upper...vehicle platforms and missions. JAUGS uses the Society of Automotive Engineers Generic Open Architecture framework to classify UGV interfaces and

Safe Operation of Mobile Unmanned Ground Vehicle (UGV) Systems

DTIC Science & Technology

2010-07-13

vehicle could go during uncommanded movement and full throttle acceleration. 4. TEST PROCEDURES. 4.1 Vehicle Subsystem Tests. These tests identify...time required to go from straight ahead to full deflection in one direction. (sec) i. Observations on ability of the remote operator to maintain...were well below the lateral acceleration limits of the vehicle resulting in very predictable handling traits. The primary concern , albeit subjective

Study of high-definition and stereoscopic head-aimed vision for improved teleoperation of an unmanned ground vehicle

NASA Astrophysics Data System (ADS)

Tyczka, Dale R.; Wright, Robert; Janiszewski, Brian; Chatten, Martha Jane; Bowen, Thomas A.; Skibba, Brian

2012-06-01

Nearly all explosive ordnance disposal robots in use today employ monoscopic standard-definition video cameras to relay live imagery from the robot to the operator. With this approach, operators must rely on shadows and other monoscopic depth cues in order to judge distances and object depths. Alternatively, they can contact an object with the robot's manipulator to determine its position, but that approach carries with it the risk of detonation from unintentionally disturbing the target or nearby objects. We recently completed a study in which high-definition (HD) and stereoscopic video cameras were used in addition to conventional standard-definition (SD) cameras in order to determine if higher resolutions and/or stereoscopic depth cues improve operators' overall performance of various unmanned ground vehicle (UGV) tasks. We also studied the effect that the different vision modes had on operator comfort. A total of six different head-aimed vision modes were used including normal-separation HD stereo, SD stereo, "micro" (reduced separation) SD stereo, HD mono, and SD mono (two types). In general, the study results support the expectation that higher resolution and stereoscopic vision aid UGV teleoperation, but the degree of improvement was found to depend on the specific task being performed; certain tasks derived notably more benefit from improved depth perception than others. This effort was sponsored by the Joint Ground Robotics Enterprise under Robotics Technology Consortium Agreement #69-200902 T01. Technical management was provided by the U.S. Air Force Research Laboratory's Robotics Research and Development Group at Tyndall AFB, Florida.

Unmanned Ground Vehicles in Support of Irregular War: A Non-lethal Approach

DTIC Science & Technology

2011-03-15

days to clear all buildings in a very fluid and dynamic operation.43 Given the fact that no UGV can climb stairs at the same rate a human can, one can...Naval Research Lab and Carnegie Mellon University’s Robotics Institute/National Robotics Engineering Consortium for designing the early test systems...Concept Technology Demonstrations (ACTD) paved the way for follow-on development of systems like the Modular Advanced Armed Robotic System (MAARS), an

ARV robotic technologies (ART): a risk reduction effort for future unmanned systems

NASA Astrophysics Data System (ADS)

Jaster, Jeffrey F.

2006-05-01

The Army's ARV (Armed Robotic Vehicle) Robotic Technologies (ART) program is working on the development of various technological thrusts for use in the robotic forces of the future. The ART program will develop, integrate and demonstrate the technology required to advance the maneuver technologies (i.e., perception, mobility, tactical behaviors) and increase the survivability of unmanned platforms for the future force while focusing on reducing the soldiers' burden by providing an increase in vehicle autonomy coinciding with a decrease in the total number user interventions required to control the unmanned assets. This program will advance the state of the art in perception technologies to provide the unmanned platform an increasingly accurate view of the terrain that surrounds it; while developing tactical/mission behavior technologies to provide the Unmanned Ground Vehicle (UGV) the capability to maneuver tactically, in conjunction with the manned systems in an autonomous mode. The ART testbed will be integrated with the advanced technology software and associated hardware developed under this effort, and incorporate appropriate mission modules (e.g. RSTA sensors, MILES, etc.) to support Warfighter experiments and evaluations (virtual and field) in a military significant environment (open/rolling and complex/urban terrain). The outcome of these experiments as well as other lessons learned through out the program life cycle will be used to reduce the current risks that are identified for the future UGV systems that will be developed under the Future Combat Systems (FCS) program, including the early integration of an FCS-like autonomous navigation system onto a tracked skid steer platform.

Advanced wireless mobile collaborative sensing network for tactical and strategic missions

NASA Astrophysics Data System (ADS)

Xu, Hao

2017-05-01

In this paper, an advanced wireless mobile collaborative sensing network will be developed. Through properly combining wireless sensor network, emerging mobile robots and multi-antenna sensing/communication techniques, we could demonstrate superiority of developed sensing network. To be concrete, heterogeneous mobile robots including unmanned aerial vehicle (UAV) and unmanned ground vehicle (UGV) are equipped with multi-model sensors and wireless transceiver antennas. Through real-time collaborative formation control, multiple mobile robots can team the best formation that can provide most accurate sensing results. Also, formatting multiple mobile robots can also construct a multiple-input multiple-output (MIMO) communication system that can provide a reliable and high performance communication network.

Water Detection Based on Object Reflections

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Matthies, Larry H.

2012-01-01

Water bodies are challenging terrain hazards for terrestrial unmanned ground vehicles (UGVs) for several reasons. Traversing through deep water bodies could cause costly damage to the electronics of UGVs. Additionally, a UGV that is either broken down due to water damage or becomes stuck in a water body during an autonomous operation will require rescue, potentially drawing critical resources away from the primary operation and increasing the operation cost. Thus, robust water detection is a critical perception requirement for UGV autonomous navigation. One of the properties useful for detecting still water bodies is that their surface acts as a horizontal mirror at high incidence angles. Still water bodies in wide-open areas can be detected by geometrically locating the exact pixels in the sky that are reflecting on candidate water pixels on the ground, predicting if ground pixels are water based on color similarity to the sky and local terrain features. But in cluttered areas where reflections of objects in the background dominate the appearance of the surface of still water bodies, detection based on sky reflections is of marginal value. Specifically, this software attempts to solve the problem of detecting still water bodies on cross-country terrain in cluttered areas at low cost.

Multi-Sensor Mud Detection

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Matthies, Larry H.

2010-01-01

Robust mud detection is a critical perception requirement for Unmanned Ground Vehicle (UGV) autonomous offroad navigation. A military UGV stuck in a mud body during a mission may have to be sacrificed or rescued, both of which are unattractive options. There are several characteristics of mud that may be detectable with appropriate UGV-mounted sensors. For example, mud only occurs on the ground surface, is cooler than surrounding dry soil during the daytime under nominal weather conditions, is generally darker than surrounding dry soil in visible imagery, and is highly polarized. However, none of these cues are definitive on their own. Dry soil also occurs on the ground surface, shadows, snow, ice, and water can also be cooler than surrounding dry soil, shadows are also darker than surrounding dry soil in visible imagery, and cars, water, and some vegetation are also highly polarized. Shadows, snow, ice, water, cars, and vegetation can all be disambiguated from mud by using a suite of sensors that span multiple bands in the electromagnetic spectrum. Because there are military operations when it is imperative for UGV's to operate without emitting strong, detectable electromagnetic signals, passive sensors are desirable. JPL has developed a daytime mud detection capability using multiple passive imaging sensors. Cues for mud from multiple passive imaging sensors are fused into a single mud detection image using a rule base, and the resultant mud detection is localized in a terrain map using range data generated from a stereo pair of color cameras.

The development of a UGV-mounted automated refueling system for VTOL UAVs

NASA Astrophysics Data System (ADS)

Wills, Mike; Burmeister, Aaron; Nelson, Travis; Denewiler, Thomas; Mullens, Kathy

2006-05-01

This paper describes the latest efforts to develop an Automated UAV Mission System (AUMS) for small vertical takeoff and landing (VTOL) unmanned air vehicles (UAVs). In certain applications such as force protection, perimeter security, and urban surveillance a VTOL UAV can provide far greater utility than fixed-wing UAVs or ground-based sensors. The VTOL UAV can operate much closer to an object of interest and can provide a hover-and-stare capability to keep its sensors trained on an object, while the fixed wing UAV would be forced into a higher altitude loitering pattern where its sensors would be subject to intermittent blockage by obstacles and terrain. The most significant disadvantage of a VTOL UAV when compared to a fixed-wing UAV is its reduced flight endurance. AUMS addresses this disadvantage by providing forward staging, refueling, and recovery capabilities for the VTOL UAV through a host unmanned ground vehicle (UGV), which serves as a launch/recovery platform and service station. The UGV has sufficient payload capacity to carry UAV fuel for multiple launch, recovery, and refuel iterations. The UGV also provides a highly mobile means of forward deploying a small UAV into hazardous areas unsafe for personnel, such as chemically or biologically contaminated areas. Teaming small UAVs with large UGVs can decrease risk to personnel and expand mission capabilities and effectiveness. There are numerous technical challenges being addressed by these development efforts. Among the challenges is the development and integration of a precision landing system compact and light enough to allow it to be mounted on a small VTOL UAV while providing repeatable landing accuracy to safely land on the AUMS. Another challenge is the design of a UGV-transportable, expandable, self-centering landing pad that contains hardware and safety devices for automatically refueling the UAV. A third challenge is making the design flexible enough to accommodate different types of VTOL UAVs, such as the AAI iSTAR ducted-fan vehicle and small helicopter UAVs. Finally, a common command-and-control architecture which supports the UAV, UGV, and AUMS must be developed and interfaced with these systems to allow fully autonomous collaborative behaviors. Funded by the Joint Robotics Program, AUMS is part of a joint effort with the Air Force Research Laboratory and the Army Missile Research Development and Engineering Command. The objective is to develop and demonstrate UGVUAV teaming concepts and work with the warfighter to ensure that future upgrades are focused on operational requirements. This paper describes the latest achievements in AUMS development and some of the military program and first responder situations that could benefit from this system.

Spectrally queued feature selection for robotic visual odometery

NASA Astrophysics Data System (ADS)

Pirozzo, David M.; Frederick, Philip A.; Hunt, Shawn; Theisen, Bernard; Del Rose, Mike

2011-01-01

Over the last two decades, research in Unmanned Vehicles (UV) has rapidly progressed and become more influenced by the field of biological sciences. Researchers have been investigating mechanical aspects of varying species to improve UV air and ground intrinsic mobility, they have been exploring the computational aspects of the brain for the development of pattern recognition and decision algorithms and they have been exploring perception capabilities of numerous animals and insects. This paper describes a 3 month exploratory applied research effort performed at the US ARMY Research, Development and Engineering Command's (RDECOM) Tank Automotive Research, Development and Engineering Center (TARDEC) in the area of biologically inspired spectrally augmented feature selection for robotic visual odometry. The motivation for this applied research was to develop a feasibility analysis on multi-spectrally queued feature selection, with improved temporal stability, for the purposes of visual odometry. The intended application is future semi-autonomous Unmanned Ground Vehicle (UGV) control as the richness of data sets required to enable human like behavior in these systems has yet to be defined.

TARDEC's Intelligent Ground Systems overview

NASA Astrophysics Data System (ADS)

Jaster, Jeffrey F.

2009-05-01

The mission of the Intelligent Ground Systems (IGS) Area at the Tank Automotive Research, Development and Engineering Center (TARDEC) is to conduct technology maturation and integration to increase Soldier robot control/interface intuitiveness and robotic ground system robustness, functionality and overall system effectiveness for the Future Combat System Brigade Combat Team, Robotics Systems Joint Project Office and game changing capabilities to be fielded beyond the current force. This is accomplished through technology component development focused on increasing unmanned ground vehicle autonomy, optimizing crew interfaces and mission planners that capture commanders' intent, integrating payloads that provide 360 degree local situational awareness and expanding current UGV tactical behavior, learning and adaptation capabilities. The integration of these technology components into ground vehicle demonstrators permits engineering evaluation, User assessment and performance characterization in increasingly complex, dynamic and relevant environments to include high speed on road or cross country operations, all weather/visibility conditions and military operations in urban terrain (MOUT). Focused testing and experimentation is directed at reducing PM risk areas (safe operations, autonomous maneuver, manned-unmanned collaboration) and transitioning technology in the form of hardware, software algorithms, test and performance data, as well as User feedback and lessons learned.

Integrated long-range UAV/UGV collaborative target tracking

NASA Astrophysics Data System (ADS)

Moseley, Mark B.; Grocholsky, Benjamin P.; Cheung, Carol; Singh, Sanjiv

2009-05-01

Coordinated operations between unmanned air and ground assets allow leveraging of multi-domain sensing and increase opportunities for improving line of sight communications. While numerous military missions would benefit from coordinated UAV-UGV operations, foundational capabilities that integrate stove-piped tactical systems and share available sensor data are required and not yet available. iRobot, AeroVironment, and Carnegie Mellon University are working together, partially SBIR-funded through ARDEC's small unit network lethality initiative, to develop collaborative capabilities for surveillance, targeting, and improved communications based on PackBot UGV and Raven UAV platforms. We integrate newly available technologies into computational, vision, and communications payloads and develop sensing algorithms to support vision-based target tracking. We first simulated and then applied onto real tactical platforms an implementation of Decentralized Data Fusion, a novel technique for fusing track estimates from PackBot and Raven platforms for a moving target in an open environment. In addition, system integration with AeroVironment's Digital Data Link onto both air and ground platforms has extended our capabilities in communications range to operate the PackBot as well as in increased video and data throughput. The system is brought together through a unified Operator Control Unit (OCU) for the PackBot and Raven that provides simultaneous waypoint navigation and traditional teleoperation. We also present several recent capability accomplishments toward PackBot-Raven coordinated operations, including single OCU display design and operation, early target track results, and Digital Data Link integration efforts, as well as our near-term capability goals.

Landmark-based robust navigation for tactical UGV control in GPS-denied communication-degraded environments

NASA Astrophysics Data System (ADS)

Endo, Yoichiro; Balloch, Jonathan C.; Grushin, Alexander; Lee, Mun Wai; Handelman, David

2016-05-01

Control of current tactical unmanned ground vehicles (UGVs) is typically accomplished through two alternative modes of operation, namely, low-level manual control using joysticks and high-level planning-based autonomous control. Each mode has its own merits as well as inherent mission-critical disadvantages. Low-level joystick control is vulnerable to communication delay and degradation, and high-level navigation often depends on uninterrupted GPS signals and/or energy-emissive (non-stealth) range sensors such as LIDAR for localization and mapping. To address these problems, we have developed a mid-level control technique where the operator semi-autonomously drives the robot relative to visible landmarks that are commonly recognizable by both humans and machines such as closed contours and structured lines. Our novel solution relies solely on optical and non-optical passive sensors and can be operated under GPS-denied, communication-degraded environments. To control the robot using these landmarks, we developed an interactive graphical user interface (GUI) that allows the operator to select landmarks in the robot's view and direct the robot relative to one or more of the landmarks. The integrated UGV control system was evaluated based on its ability to robustly navigate through indoor environments. The system was successfully field tested with QinetiQ North America's TALON UGV and Tactical Robot Controller (TRC), a ruggedized operator control unit (OCU). We found that the proposed system is indeed robust against communication delay and degradation, and provides the operator with steady and reliable control of the UGV in realistic tactical scenarios.

Daytime Water Detection Based on Color Variation

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Matthies, Larry H.

2010-01-01

Robust water detection is a critical perception requirement for unmanned ground vehicle (UGV) autonomous navigation. This is particularly true in wide open areas where water can collect in naturally occurring terrain depressions during periods of heavy precipitation and form large water bodies (such as ponds). At far range, reflections of the sky provide a strong cue for water. But at close range, the color coming out of a water body dominates sky reflections and the water cue from sky reflections is of marginal use. We model this behavior by using water body intensity data from multiple frames of RGB imagery to estimate the total reflection coefficient contribution from surface reflections and the combination of all other factors. Then we describe an algorithm that uses one of the color cameras in a forward- looking, UGV-mounted stereo-vision perception system to detect water bodies in wide open areas. This detector exploits the knowledge that the change in saturation-to-brightness ratio across a water body from the leading to trailing edge is uniform and distinct from other terrain types. In test sequences approaching a pond under clear, overcast, and cloudy sky conditions, the true positive and false negative water detection rates were (95.76%, 96.71%, 98.77%) and (0.45%, 0.60%, 0.62%), respectively. This software has been integrated on an experimental unmanned vehicle and field tested at Ft. Indiantown Gap, PA.

Stereo-vision-based terrain mapping for off-road autonomous navigation

NASA Astrophysics Data System (ADS)

Rankin, Arturo L.; Huertas, Andres; Matthies, Larry H.

2009-05-01

Successful off-road autonomous navigation by an unmanned ground vehicle (UGV) requires reliable perception and representation of natural terrain. While perception algorithms are used to detect driving hazards, terrain mapping algorithms are used to represent the detected hazards in a world model a UGV can use to plan safe paths. There are two primary ways to detect driving hazards with perception sensors mounted to a UGV: binary obstacle detection and traversability cost analysis. Binary obstacle detectors label terrain as either traversable or non-traversable, whereas, traversability cost analysis assigns a cost to driving over a discrete patch of terrain. In uncluttered environments where the non-obstacle terrain is equally traversable, binary obstacle detection is sufficient. However, in cluttered environments, some form of traversability cost analysis is necessary. The Jet Propulsion Laboratory (JPL) has explored both approaches using stereo vision systems. A set of binary detectors has been implemented that detect positive obstacles, negative obstacles, tree trunks, tree lines, excessive slope, low overhangs, and water bodies. A compact terrain map is built from each frame of stereo images. The mapping algorithm labels cells that contain obstacles as nogo regions, and encodes terrain elevation, terrain classification, terrain roughness, traversability cost, and a confidence value. The single frame maps are merged into a world map where temporal filtering is applied. In previous papers, we have described our perception algorithms that perform binary obstacle detection. In this paper, we summarize the terrain mapping capabilities that JPL has implemented during several UGV programs over the last decade and discuss some challenges to building terrain maps with stereo range data.

Stereo Vision Based Terrain Mapping for Off-Road Autonomous Navigation

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Huertas, Andres; Matthies, Larry H.

2009-01-01

Successful off-road autonomous navigation by an unmanned ground vehicle (UGV) requires reliable perception and representation of natural terrain. While perception algorithms are used to detect driving hazards, terrain mapping algorithms are used to represent the detected hazards in a world model a UGV can use to plan safe paths. There are two primary ways to detect driving hazards with perception sensors mounted to a UGV: binary obstacle detection and traversability cost analysis. Binary obstacle detectors label terrain as either traversable or non-traversable, whereas, traversability cost analysis assigns a cost to driving over a discrete patch of terrain. In uncluttered environments where the non-obstacle terrain is equally traversable, binary obstacle detection is sufficient. However, in cluttered environments, some form of traversability cost analysis is necessary. The Jet Propulsion Laboratory (JPL) has explored both approaches using stereo vision systems. A set of binary detectors has been implemented that detect positive obstacles, negative obstacles, tree trunks, tree lines, excessive slope, low overhangs, and water bodies. A compact terrain map is built from each frame of stereo images. The mapping algorithm labels cells that contain obstacles as no-go regions, and encodes terrain elevation, terrain classification, terrain roughness, traversability cost, and a confidence value. The single frame maps are merged into a world map where temporal filtering is applied. In previous papers, we have described our perception algorithms that perform binary obstacle detection. In this paper, we summarize the terrain mapping capabilities that JPL has implemented during several UGV programs over the last decade and discuss some challenges to building terrain maps with stereo range data.

Water Detection Based on Sky Reflections

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Matthies, Larry H.

2010-01-01

This software has been designed to detect water bodies that are out in the open on cross-country terrain at mid- to far-range (approximately 20 100 meters), using imagery acquired from a stereo pair of color cameras mounted on a terrestrial, unmanned ground vehicle (UGV). Non-traversable water bodies, such as large puddles, ponds, and lakes, are indirectly detected by detecting reflections of the sky below the horizon in color imagery. The appearance of water bodies in color imagery largely depends on the ratio of light reflected off the water surface to the light coming out of the water body. When a water body is far away, the angle of incidence is large, and the light reflected off the water surface dominates. We have exploited this behavior to detect water bodies out in the open at mid- to far-range. When a water body is detected at far range, a UGV s path planner can begin to look for alternate routes to the goal position sooner, rather than later. As a result, detecting water hazards at far range generally reduces the time required to reach a goal position during autonomous navigation. This software implements a new water detector based on sky reflections that geometrically locates the exact pixel in the sky that is reflecting on a candidate water pixel on the ground, and predicts if the ground pixel is water based on color similarity and local terrain features

Using probabilistic model as feature descriptor on a smartphone device for autonomous navigation of unmanned ground vehicles

NASA Astrophysics Data System (ADS)

Desai, Alok; Lee, Dah-Jye

2013-12-01

There has been significant research on the development of feature descriptors in the past few years. Most of them do not emphasize real-time applications. This paper presents the development of an affine invariant feature descriptor for low resource applications such as UAV and UGV that are equipped with an embedded system with a small microprocessor, a field programmable gate array (FPGA), or a smart phone device. UAV and UGV have proven suitable for many promising applications such as unknown environment exploration, search and rescue operations. These applications required on board image processing for obstacle detection, avoidance and navigation. All these real-time vision applications require a camera to grab images and match features using a feature descriptor. A good feature descriptor will uniquely describe a feature point thus allowing it to be correctly identified and matched with its corresponding feature point in another image. A few feature description algorithms are available for a resource limited system. They either require too much of the device's resource or too much simplification on the algorithm, which results in reduction in performance. This research is aimed at meeting the needs of these systems without sacrificing accuracy. This paper introduces a new feature descriptor called PRObabilistic model (PRO) for UGV navigation applications. It is a compact and efficient binary descriptor that is hardware-friendly and easy for implementation.

A pose estimation method for unmanned ground vehicles in GPS denied environments

NASA Astrophysics Data System (ADS)

Tamjidi, Amirhossein; Ye, Cang

2012-06-01

This paper presents a pose estimation method based on the 1-Point RANSAC EKF (Extended Kalman Filter) framework. The method fuses the depth data from a LIDAR and the visual data from a monocular camera to estimate the pose of a Unmanned Ground Vehicle (UGV) in a GPS denied environment. Its estimation framework continuy updates the vehicle's 6D pose state and temporary estimates of the extracted visual features' 3D positions. In contrast to the conventional EKF-SLAM (Simultaneous Localization And Mapping) frameworks, the proposed method discards feature estimates from the extended state vector once they are no longer observed for several steps. As a result, the extended state vector always maintains a reasonable size that is suitable for online calculation. The fusion of laser and visual data is performed both in the feature initialization part of the EKF-SLAM process and in the motion prediction stage. A RANSAC pose calculation procedure is devised to produce pose estimate for the motion model. The proposed method has been successfully tested on the Ford campus's LIDAR-Vision dataset. The results are compared with the ground truth data of the dataset and the estimation error is ~1.9% of the path length.

SAFER vehicle inspection: a multimodal robotic sensing platform

NASA Astrophysics Data System (ADS)

Page, David L.; Fougerolle, Yohan; Koschan, Andreas F.; Gribok, Andrei; Abidi, Mongi A.; Gorsich, David J.; Gerhart, Grant R.

2004-09-01

The current threats to U.S. security both military and civilian have led to an increased interest in the development of technologies to safeguard national facilities such as military bases, federal buildings, nuclear power plants, and national laboratories. As a result, the Imaging, Robotics, and Intelligent Systems (IRIS) Laboratory at The University of Tennessee (UT) has established a research consortium, known as SAFER (Security Automation and Future Electromotive Robotics), to develop, test, and deploy sensing and imaging systems for unmanned ground vehicles (UGV). The targeted missions for these UGV systems include -- but are not limited to --under vehicle threat assessment, stand-off check-point inspections, scout surveillance, intruder detection, obstacle-breach situations, and render-safe scenarios. This paper presents a general overview of the SAFER project. Beyond this general overview, we further focus on a specific problem where we collect 3D range scans of under vehicle carriages. These scans require appropriate segmentation and representation algorithms to facilitate the vehicle inspection process. We discuss the theory for these algorithms and present results from applying them to actual vehicle scans.

Intelligent mobility for robotic vehicles in the army after next

NASA Astrophysics Data System (ADS)

Gerhart, Grant R.; Goetz, Richard C.; Gorsich, David J.

1999-07-01

The TARDEC Intelligent Mobility program addresses several essential technologies necessary to support the army after next (AAN) concept. Ground forces in the AAN time frame will deploy robotic unmanned ground vehicles (UGVs) in high-risk missions to avoid exposing soldiers to both friendly and unfriendly fire. Prospective robotic systems will include RSTA/scout vehicles, combat engineering/mine clearing vehicles, indirect fire artillery and missile launch platforms. The AAN concept requires high on-road and off-road mobility, survivability, transportability/deployability and low logistics burden. TARDEC is developing a robotic vehicle systems integration laboratory (SIL) to evaluate technologies and their integration into future UGV systems. Example technologies include the following: in-hub electric drive, omni-directional wheel and steering configurations, off-road tires, adaptive tire inflation, articulated vehicles, active suspension, mine blast protection, detection avoidance and evasive maneuver. This paper will describe current developments in these areas relative to the TARDEC intelligent mobility program.

Development for SSV on a parallel processing system (PARAGON)

NASA Astrophysics Data System (ADS)

Gothard, Benny M.; Allmen, Mark; Carroll, Michael J.; Rich, Dan

1995-12-01

A goal of the surrogate semi-autonomous vehicle (SSV) program is to have multiple vehicles navigate autonomously and cooperatively with other vehicles. This paper describes the process and tools used in porting UGV/SSV (unmanned ground vehicle) autonomous mobility and target recognition algorithms from a SISD (single instruction single data) processor architecture (i.e., a Sun SPARC workstation running C/UNIX) to a MIMD (multiple instruction multiple data) parallel processor architecture (i.e., PARAGON-a parallel set of i860 processors running C/UNIX). It discusses the gains in performance and the pitfalls of such a venture. It also examines the merits of this processor architecture (based on this conceptual prototyping effort) and programming paradigm to meet the final SSV demonstration requirements.

Achieving integrated convoys: cargo unmanned ground vehicle development and experimentation

NASA Astrophysics Data System (ADS)

Zych, Noah; Silver, David; Stager, David; Green, Colin; Pilarski, Thomas; Fischer, Jacob

2013-05-01

The Cargo UGV project was initiated in 2010 with the aim of developing and experimenting with advanced autonomous vehicles capable of being integrated unobtrusively into manned logistics convoys. The intent was to validate two hypotheses in complex, operationally representative environments: first, that unmanned tactical wheeled vehicles provide a force protection advantage by creating standoff distance to warfighters during ambushes or improvised explosive device attacks; and second, that these UGVs serve as force multipliers by enabling a single operator to control multiple unmanned assets. To assess whether current state-of-the-art autonomous vehicle technology was sufficiently capable to permit resupply missions to be executed with decreased risk and reduced manpower, and to assess the effect of UGVs on customary convoy tactics, the Marine Corps Warfighting Laboratory and the Joint Ground Robotics Enterprise sponsored Oshkosh Defense and the National Robotics Engineering Center to equip two standard Marine Corps cargo trucks for autonomous operation. This paper details the system architecture, hardware implementation, and software modules developed to meet the vehicle control, perception, and planner requirements compelled by this application. Additionally, the design of a custom human machine interface and an accompanying training program are described, as is the creation of a realistic convoy simulation environment for rapid system development. Finally, results are conveyed from a warfighter experiment in which the effectiveness of the training program for novice operators was assessed, and the impact of the UGVs on convoy operations was observed in a variety of scenarios via direct comparison to a fully manned convoy.

Scalable autonomous operations of unmanned assets

NASA Astrophysics Data System (ADS)

Jung, Sunghun

Although there have been great theoretical advances in the region of Unmanned Aerial Vehicle (UAV) autonomy, applications of those theories into real world are still hesitated due to unexpected disturbances. Most of UAVs which are currently used are mainly, strictly speaking, Remotely Piloted Vehicles (RPA) since most works related with the flight control, sensor data analysis, and decision makings are done by human operators. To increase the degree of autonomy, many researches are focused on developing Unmanned Autonomous Aerial Vehicle (UAAV) which can takeoff, fly to the interested area by avoiding unexpected obstacles, perform various missions with decision makings, come back to the base station, and land on by itself without any human operators. To improve the performance of UAVs, the accuracies of position and orientation sensors are enhanced by integrating a Unmanned Ground Vehicle (UGV) or a solar compass to a UAV; Position sensor accuracy of a GPS sensor on a UAV is improved by referencing the position of a UGV which is calculated by using three GPS sensors and Weighted Centroid Localization (WCL) method; Orientation sensor accuracy is improved as well by using Three Pixel Theorem (TPT) and integrating a solar compass which composed of nine light sensors to a magnetic compass. Also, improved health management of a UAV is fulfilled by developing a wireless autonomous charging station which uses four pairs of transmitter and receiver magnetic loops with four robotic arms. For the software aspect, I also analyze the error propagation of the proposed mission planning hierarchy to achieve the safest size of the buffer zone. In addition, among seven future research areas regarding UAV, this paper mainly focuses on developing algorithms of path planning, trajectory generation, and cooperative tactics for the operations of multiple UAVs using GA based multiple Traveling Salesman Problem (mTSP) which is solved by dividing into m number of Traveling Salesman Problems (TSP) using two region division methods such as Uniform Region Division (URD) and K-means Voronoi Region Division (KVRD). The topic of the maximum fuel efficiency is also dealt to ensure the minimum amount fuel consumption to perform surveillance on a given region using multiple UAVs. Last but not least, I present an application example of cattle roundup with two UAVs and two animals using the feedback linearization controller.

The influence of camouflage, obstruction, familiarity and spatial ability on target identification from an unmanned ground vehicle.

PubMed

Fincannon, Thomas; Keebler, Joseph R; Jentsch, Florian; Curtis, Michael

2013-01-01

The purpose of this study was to examine the effects of environmental and cognitive factors on the identification of targets from an unmanned ground vehicle (UGV). This was accomplished by manipulating obstruction, camouflage and familiarity of objects in the environment, while also measuring spatial ability. The effects of these variables on target identification were studied by measuring performance of participants that observed pre-recorded video from a 1:35 scaled military operations in urban terrain facility. Analyses indicated that a combination of camouflage and obstruction caused the most detrimental effects on performance, and that there were differences in the recognition of familiar and unfamiliar targets. Further analysis indicated that these detrimental effects could only be overcome with a combination of target familiarity and spatial ability. The findings highlight the degree to which environmental factors hinder performance and the need for a multidimensional approach for improving performance under these conditions. Areas in need of future research are also discussed. Cognitive theory is applied to the problem of perception from UGVs. Results from an experimental study indicate that a combination of camouflage and obstruction caused the most detrimental effects on performance, with differences in the recognition of both familiar and unfamiliar targets. Familiarity and spatial ability interacted to predict the performance.

Soldier experiments and assessments using SPEAR speech control system for UGVs

NASA Astrophysics Data System (ADS)

Brown, Jonathan; Blanco, Chris; Czerniak, Jeffrey; Hoffman, Brian; Hoffman, Orin; Juneja, Amit; Ngia, Lester; Pruthi, Tarun; Liu, Dongqing

2010-04-01

This paper reports on a Soldier Experiment performed by the Army Research Lab's Human Research Engineering Directorate (HRED) Field Element located at the Maneuver Center of Excellence, Ft. Benning, and a Limited Use Assessment conducted by the Marine Corps Forces Pacific Command Experimentation Center (MEC) at Camp Pendleton evaluating the effectiveness of using speech commands to control an Unmanned Ground Vehicle. SPEAR, developed by Think-A-Move, Ltd., provides speech control of UGVs. SPEAR detects user speech in the ear canal with an earpiece containing an in-ear microphone. The system design provides up to 30 dB of passive noise reduction, enabling it to work well in high-noise environments, where traditional speech systems, using external microphones, fail; it also utilizes a proprietary speech recognition engine. SPEAR has been integrated with iRobot's PackBot 510 with FasTac Kit, and with Multi-Robot Operator Control Unit (MOCU), developed by SPAWAR Systems Center Pacific. These integrated systems allow speech to supplement the hand-controller for multi-modal control of different UGV functions simultaneously. HRED's experiment measured the impact of SPEAR on reducing the cognitive load placed on UGV Operators and the time to complete specific tasks. Army NCOs and Officer School Candidates participated in this experiment, which found that speech control was faster than manual control to complete tasks requiring menu navigation, as well as reducing the cognitive load on UGV Operators. The MEC assessment examined speech commands used for two different missions: Route Clearance and Cordon and Search; participants included Explosive Ordnance Disposal Technicians and Combat Engineers. The majority of the Marines thought it was easier to complete the mission scenarios with SPEAR than with only using manual controls, and that using SPEAR improved their situational awareness. Overall results of these Assessments are reported in the paper, along with possible applications to autonomous mine detection systems.

Control of a Quadcopter Aerial Robot Using Optic Flow Sensing

NASA Astrophysics Data System (ADS)

Hurd, Michael Brandon

This thesis focuses on the motion control of a custom-built quadcopter aerial robot using optic flow sensing. Optic flow sensing is a vision-based approach that can provide a robot the ability to fly in global positioning system (GPS) denied environments, such as indoor environments. In this work, optic flow sensors are used to stabilize the motion of quadcopter robot, where an optic flow algorithm is applied to provide odometry measurements to the quadcopter's central processing unit to monitor the flight heading. The optic-flow sensor and algorithm are capable of gathering and processing the images at 250 frames/sec, and the sensor package weighs 2.5 g and has a footprint of 6 cm2 in area. The odometry value from the optic flow sensor is then used a feedback information in a simple proportional-integral-derivative (PID) controller on the quadcopter. Experimental results are presented to demonstrate the effectiveness of using optic flow for controlling the motion of the quadcopter aerial robot. The technique presented herein can be applied to different types of aerial robotic systems or unmanned aerial vehicles (UAVs), as well as unmanned ground vehicles (UGV).

ARL participation in the C4ISR OTM experiment: integration and performance results

NASA Astrophysics Data System (ADS)

Zong, Lei; O'Brien, Barry J.

2007-04-01

The Command, Control, Communication, Computers, Intelligence, Surveillance and Reconnaissance (C4ISR) On-The- Move (OTM) demonstration is an annual showcase of how innovative technologies can help modern troops increase their situational awareness (SA) in battlefield environments. To evaluate the effectiveness these new technologies have on the soldiers' abilities to gather situational information, the demonstration involves United States Army National Guard troops in realistic war game scenarios at an Army Reserve training ground. The Army Research Laboratory (ARL) was invited to participate in the event, with the objective demonstrating system-level integration of disparate technologies developed for gathering SA information in small unit combat operations. ARL provided expertise in Unattended Ground Sensing (UGS) technology, Unmanned Ground Vehicle (UGV) technology, information processing and wireless mobile ad hoc communication. The ARL C4ISR system included a system of multimodal sensors (MMS), a trip wire imager, a man-portable robotic vehicle (PackBot), and low power sensor radios for communication between an ARL system and a hosting platoon vehicle. This paper will focus on the integration effort of bringing the multiple families of sensor assets together into a working system.

TARDEC Annual Report 2010

DTIC Science & Technology

2011-06-15

capable of engaging threats while interacting with system operators. Through autonomous perception and navigation, intelligent tactical behavior... systems integration approach. TARDEC’s role is to assess the best way to apply the VICTORY architecture to future tactical wheeled vehicles and...Track tops Thrown Object Protection System traDoc U.S. Army Training and Doctrine Command twVs Tactical Wheeled Vehicle Survivability ugV Unmanned

UGV acceptance testing

NASA Astrophysics Data System (ADS)

Kramer, Jeffrey A.; Murphy, Robin R.

2006-05-01

With over 100 models of unmanned vehicles now available for military and civilian safety, security or rescue applications, it is important to for agencies to establish acceptance testing. However, there appears to be no general guidelines for what constitutes a reasonable acceptance test. This paper describes i) a preliminary method for acceptance testing by a customer of the mechanical and electrical components of an unmanned ground vehicle system, ii) how it has been applied to a man-packable micro-robot, and iii) discusses the value of testing both to ensure that the customer has a workable system and to improve design. The test method automated the operation of the robot to repeatedly exercise all aspects and combinations of components on the robot for 6 hours. The acceptance testing process uncovered many failures consistent with those shown to occur in the field, showing that testing by the user does predict failures. The process also demonstrated that the testing by the manufacturer can provide important design data that can be used to identify, diagnose, and prevent long-term problems. Also, the structured testing environment showed that sensor systems can be used to predict errors and changes in performance, as well as uncovering unmodeled behavior in subsystems.

Force Protection via UGV-UAV Collaboration: Development of Control Law for Vision Based Target Tracking on SUAV

DTIC Science & Technology

2007-12-01

Hardware - In - Loop , Piccolo, UAV, Unmanned Aerial Vehicle 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT...Maneuvering Target.......................... 35 C. HARDWARE - IN - LOOP SIMULATION............................................... 37 1. Hardware - In - Loop Setup...law as proposed in equation (23) is capable of tracking a maneuvering target. C. HARDWARE - IN - LOOP SIMULATION The intention of HIL simulation

Fast Fingerprint Database Maintenance for Indoor Positioning Based on UGV SLAM

PubMed Central

Tang, Jian; Chen, Yuwei; Chen, Liang; Liu, Jingbin; Hyyppä, Juha; Kukko, Antero; Kaartinen, Harri; Hyyppä, Hannu; Chen, Ruizhi

2015-01-01

Indoor positioning technology has become more and more important in the last two decades. Utilizing Received Signal Strength Indicator (RSSI) fingerprints of Signals of OPportunity (SOP) is a promising alternative navigation solution. However, as the RSSIs vary during operation due to their physical nature and are easily affected by the environmental change, one challenge of the indoor fingerprinting method is maintaining the RSSI fingerprint database in a timely and effective manner. In this paper, a solution for rapidly updating the fingerprint database is presented, based on a self-developed Unmanned Ground Vehicles (UGV) platform NAVIS. Several SOP sensors were installed on NAVIS for collecting indoor fingerprint information, including a digital compass collecting magnetic field intensity, a light sensor collecting light intensity, and a smartphone which collects the access point number and RSSIs of the pre-installed WiFi network. The NAVIS platform generates a map of the indoor environment and collects the SOPs during processing of the mapping, and then the SOP fingerprint database is interpolated and updated in real time. Field tests were carried out to evaluate the effectiveness and efficiency of the proposed method. The results showed that the fingerprint databases can be quickly created and updated with a higher sampling frequency (5Hz) and denser reference points compared with traditional methods, and the indoor map can be generated without prior information. Moreover, environmental changes could also be detected quickly for fingerprint indoor positioning. PMID:25746096

Real-time yield estimation based on deep learning

NASA Astrophysics Data System (ADS)

Rahnemoonfar, Maryam; Sheppard, Clay

2017-05-01

Crop yield estimation is an important task in product management and marketing. Accurate yield prediction helps farmers to make better decision on cultivation practices, plant disease prevention, and the size of harvest labor force. The current practice of yield estimation based on the manual counting of fruits is very time consuming and expensive process and it is not practical for big fields. Robotic systems including Unmanned Aerial Vehicles (UAV) and Unmanned Ground Vehicles (UGV), provide an efficient, cost-effective, flexible, and scalable solution for product management and yield prediction. Recently huge data has been gathered from agricultural field, however efficient analysis of those data is still a challenging task. Computer vision approaches currently face diffident challenges in automatic counting of fruits or flowers including occlusion caused by leaves, branches or other fruits, variance in natural illumination, and scale. In this paper a novel deep convolutional network algorithm was developed to facilitate the accurate yield prediction and automatic counting of fruits and vegetables on the images. Our method is robust to occlusion, shadow, uneven illumination and scale. Experimental results in comparison to the state-of-the art show the effectiveness of our algorithm.

STARR: shortwave-targeted agile Raman robot for the detection and identification of emplaced explosives

NASA Astrophysics Data System (ADS)

Gomer, Nathaniel R.; Gardner, Charles W.

2014-05-01

In order to combat the threat of emplaced explosives (land mines, etc.), ChemImage Sensor Systems (CISS) has developed a multi-sensor, robot mounted sensor capable of identification and confirmation of potential threats. The system, known as STARR (Shortwave-infrared Targeted Agile Raman Robot), utilizes shortwave infrared spectroscopy for the identification of potential threats, combined with a visible short-range standoff Raman hyperspectral imaging (HSI) system for material confirmation. The entire system is mounted onto a Talon UGV (Unmanned Ground Vehicle), giving the sensor an increased area search rate and reducing the risk of injury to the operator. The Raman HSI system utilizes a fiber array spectral translator (FAST) for the acquisition of high quality Raman chemical images, allowing for increased sensitivity and improved specificity. An overview of the design and operation of the system will be presented, along with initial detection results of the fusion sensor.

LWIR passive perception system for stealthy unmanned ground vehicle night operations

NASA Astrophysics Data System (ADS)

Lee, Daren; Rankin, Arturo; Huertas, Andres; Nash, Jeremy; Ahuja, Gaurav; Matthies, Larry

2016-05-01

Resupplying forward-deployed units in rugged terrain in the presence of hostile forces creates a high threat to manned air and ground vehicles. An autonomous unmanned ground vehicle (UGV) capable of navigating stealthily at night in off-road and on-road terrain could significantly increase the safety and success rate of such resupply missions for warfighters. Passive night-time perception of terrain and obstacle features is a vital requirement for such missions. As part of the ONR 30 Autonomy Team, the Jet Propulsion Laboratory developed a passive, low-cost night-time perception system under the ONR Expeditionary Maneuver Warfare and Combating Terrorism Applied Research program. Using a stereo pair of forward looking LWIR uncooled microbolometer cameras, the perception system generates disparity maps using a local window-based stereo correlator to achieve real-time performance while maintaining low power consumption. To overcome the lower signal-to-noise ratio and spatial resolution of LWIR thermal imaging technologies, a series of pre-filters were applied to the input images to increase the image contrast and stereo correlator enhancements were applied to increase the disparity density. To overcome false positives generated by mixed pixels, noisy disparities from repeated textures, and uncertainty in far range measurements, a series of consistency, multi-resolution, and temporal based post-filters were employed to improve the fidelity of the output range measurements. The stereo processing leverages multi-core processors and runs under the Robot Operating System (ROS). The night-time passive perception system was tested and evaluated on fully autonomous testbed ground vehicles at SPAWAR Systems Center Pacific (SSC Pacific) and Marine Corps Base Camp Pendleton, California. This paper describes the challenges, techniques, and experimental results of developing a passive, low-cost perception system for night-time autonomous navigation.

Fast fingerprint database maintenance for indoor positioning based on UGV SLAM.

PubMed

Tang, Jian; Chen, Yuwei; Chen, Liang; Liu, Jingbin; Hyyppä, Juha; Kukko, Antero; Kaartinen, Harri; Hyyppä, Hannu; Chen, Ruizhi

2015-03-04

Indoor positioning technology has become more and more important in the last two decades. Utilizing Received Signal Strength Indicator (RSSI) fingerprints of Signals of OPportunity (SOP) is a promising alternative navigation solution. However, as the RSSIs vary during operation due to their physical nature and are easily affected by the environmental change, one challenge of the indoor fingerprinting method is maintaining the RSSI fingerprint database in a timely and effective manner. In this paper, a solution for rapidly updating the fingerprint database is presented, based on a self-developed Unmanned Ground Vehicles (UGV) platform NAVIS. Several SOP sensors were installed on NAVIS for collecting indoor fingerprint information, including a digital compass collecting magnetic field intensity, a light sensor collecting light intensity, and a smartphone which collects the access point number and RSSIs of the pre-installed WiFi network. The NAVIS platform generates a map of the indoor environment and collects the SOPs during processing of the mapping, and then the SOP fingerprint database is interpolated and updated in real time. Field tests were carried out to evaluate the effectiveness and efficiency of the proposed method. The results showed that the fingerprint databases can be quickly created and updated with a higher sampling frequency (5Hz) and denser reference points compared with traditional methods, and the indoor map can be generated without prior information. Moreover, environmental changes could also be detected quickly for fingerprint indoor positioning.

Laser-Based Slam with Efficient Occupancy Likelihood Map Learning for Dynamic Indoor Scenes

NASA Astrophysics Data System (ADS)

Li, Li; Yao, Jian; Xie, Renping; Tu, Jinge; Feng, Chen

2016-06-01

Location-Based Services (LBS) have attracted growing attention in recent years, especially in indoor environments. The fundamental technique of LBS is the map building for unknown environments, this technique also named as simultaneous localization and mapping (SLAM) in robotic society. In this paper, we propose a novel approach for SLAMin dynamic indoor scenes based on a 2D laser scanner mounted on a mobile Unmanned Ground Vehicle (UGV) with the help of the grid-based occupancy likelihood map. Instead of applying scan matching in two adjacent scans, we propose to match current scan with the occupancy likelihood map learned from all previous scans in multiple scales to avoid the accumulation of matching errors. Due to that the acquisition of the points in a scan is sequential but not simultaneous, there unavoidably exists the scan distortion at different extents. To compensate the scan distortion caused by the motion of the UGV, we propose to integrate a velocity of a laser range finder (LRF) into the scan matching optimization framework. Besides, to reduce the effect of dynamic objects such as walking pedestrians often existed in indoor scenes as much as possible, we propose a new occupancy likelihood map learning strategy by increasing or decreasing the probability of each occupancy grid after each scan matching. Experimental results in several challenged indoor scenes demonstrate that our proposed approach is capable of providing high-precision SLAM results.

System-on-chip-centric unattended embedded sensors in homeland security and defense applications

NASA Astrophysics Data System (ADS)

Jannson, Tomasz; Forrester, Thomas; Degrood, Kevin; Shih, Min-Yi; Walter, Kevin; Lee, Kang; Gans, Eric; Esterkin, Vladimir

2009-05-01

System-on-chip (SoC) single-die electronic integrated circuit (IC) integration has recently been attracting a great deal of attention, due to its high modularity, universality, and relatively low fabrication cost. The SoC also has low power consumption and it is naturally suited to being a base for integration of embedded sensors. Such sensors can run unattended, and can be either commercial off-the-shelf (COTS) electronic, COTS microelectromechanical systems (MEMS), or optical-COTS or produced in house (i.e., at Physical Optics Corporation, POC). In the version with the simplest electronic packaging, they can be integrated with low-power wireless RF that can communicate with a central processing unit (CPU) integrated in-house and installed on the specific platform of interest. Such a platform can be a human body (for e-clothing), unmanned aerial vehicle (UAV), unmanned ground vehicle (UGV), or many others. In this paper we discuss SoC-centric embedded unattended sensors in Homeland Security and military applications, including specific application scenarios (or CONOPS). In one specific example, we analyze an embedded polarization optical sensor produced in house, including generalized Lambertian light-emitting diode (LED) sources and secondary nonimaging optics (NIO).

Reconnaissance and Autonomy for Small Robots (RASR) team: MAGIC 2010 challenge

NASA Astrophysics Data System (ADS)

Lacaze, Alberto; Murphy, Karl; Del Giorno, Mark; Corley, Katrina

2012-06-01

The Reconnaissance and Autonomy for Small Robots (RASR) team developed a system for the coordination of groups of unmanned ground vehicles (UGVs) that can execute a variety of military relevant missions in dynamic urban environments. Historically, UGV operations have been primarily performed via tele-operation, requiring at least one dedicated operator per robot, and requiring substantial real-time bandwidth to accomplish those missions. Our team goal was to develop a system that can provide long-term value to the war-fighter, utilizing MAGIC-2010 as a stepping stone. To that end, we self-imposed a set of constraints that would force us to develop technology that could readily be used by the military in the near term: • Use a relevant (deployed) platform • Use low-cost, reliable sensors • Develop an expandable and modular control system with innovative software algorithms to minimize the computing footprint required • Minimize required communications bandwidth and handle communication losses • Minimize additional power requirements to maximize battery life and mission duration

NAVIS-An UGV indoor positioning system using laser scan matching for large-area real-time applications.

PubMed

Tang, Jian; Chen, Yuwei; Jaakkola, Anttoni; Liu, Jinbing; Hyyppä, Juha; Hyyppä, Hannu

2014-07-04

Laser scan matching with grid-based maps is a promising tool for real-time indoor positioning of mobile Unmanned Ground Vehicles (UGVs). While there are critical implementation problems, such as the ability to estimate the position by sensing the unknown indoor environment with sufficient accuracy and low enough latency for stable vehicle control, further development work is necessary. Unfortunately, most of the existing methods employ heuristics for quick positioning in which numerous accumulated errors easily lead to loss of positioning accuracy. This severely restricts its applications in large areas and over lengthy periods of time. This paper introduces an efficient real-time mobile UGV indoor positioning system for large-area applications using laser scan matching with an improved probabilistically-motivated Maximum Likelihood Estimation (IMLE) algorithm, which is based on a multi-resolution patch-divided grid likelihood map. Compared with traditional methods, the improvements embodied in IMLE include: (a) Iterative Closed Point (ICP) preprocessing, which adaptively decreases the search scope; (b) a totally brute search matching method on multi-resolution map layers, based on the likelihood value between current laser scan and the grid map within refined search scope, adopted to obtain the global optimum position at each scan matching; and (c) a patch-divided likelihood map supporting a large indoor area. A UGV platform called NAVIS was designed, manufactured, and tested based on a low-cost robot integrating a LiDAR and an odometer sensor to verify the IMLE algorithm. A series of experiments based on simulated data and field tests with NAVIS proved that the proposed IMEL algorithm is a better way to perform local scan matching that can offer a quick and stable positioning solution with high accuracy so it can be part of a large area localization/mapping, application. The NAVIS platform can reach an updating rate of 12 Hz in a feature-rich environment and 2 Hz even in a feature-poor environment, respectively. Therefore, it can be utilized in a real-time application.

UGV: security analysis of subsystem control network

NASA Astrophysics Data System (ADS)

Abbott-McCune, Sam; Kobezak, Philip; Tront, Joseph; Marchany, Randy; Wicks, Al

2013-05-01

Unmanned Ground vehicles (UGVs) are becoming prolific in the heterogeneous superset of robotic platforms. The sensors which provide odometry, localization, perception, and vehicle diagnostics are fused to give the robotic platform a sense of the environment it is traversing. The automotive industry CAN bus has dominated the industry due to the fault tolerance and the message structure allowing high priority messages to reach the desired node in a real time environment. UGVs are being researched and produced at an accelerated rate to preform arduous, repetitive, and dangerous missions that are associated with a military action in a protracted conflict. The technology and applications of the research will inevitably be turned into dual-use platforms to aid civil agencies in the performance of their various operations. Our motivation is security of the holistic system; however as subsystems are outsourced in the design, the overall security of the system may be diminished. We will focus on the CAN bus topology and the vulnerabilities introduced in UGVs and recognizable security vulnerabilities that are inherent in the communications architecture. We will show how data can be extracted from an add-on CAN bus that can be customized to monitor subsystems. The information can be altered or spoofed to force the vehicle to exhibit unwanted actions or render the UGV unusable for the designed mission. The military relies heavily on technology to maintain information dominance, and the security of the information introduced onto the network by UGVs must be safeguarded from vulnerabilities that can be exploited.

Levels of Autonomy and Autonomous System Performance Assessment for Intelligent Unmanned Systems

DTIC Science & Technology

2014-04-01

LIDAR and camera sensors that is driven entirely by teleoperation would be AL 0. If that same robot used its LIDAR and camera data to generate a...obstacle detection, mapping, path planning 3 CMMAD semi- autonomous counter- mine system (Few 2010) Talon UGV, camera, LIDAR , metal detector...NCAP framework are performed on individual UMS components and do not require mission level evaluations. For example, bench testing of camera, LIDAR

2005 9th Annual Army Small Business Conference

DTIC Science & Technology

2005-11-03

field commanders who conduct acquisitions. All the Army’s major commands located in the United States will be represented. The conference...Engineer Squad Vehicle i r i l Mobile Gun System il yst Medical Evacuation Vehicle i l v ti i l Reconnaissance Vehicle iss i l Mortar Carrier rt r rri r...Manned Systems Unmanned Air Vehicles Class I ARV-A (L) Small (Manpackable) UGV Non-Line of Sight Cannon Non-Line of Sight Mortar Medical Treatment and

Change detection on UGV patrols with respect to a reference tour using VIS imagery

NASA Astrophysics Data System (ADS)

Müller, Thomas

2015-05-01

Autonomous driving robots (UGVs, Unmanned Ground Vehicles) equipped with visual-optical (VIS) cameras offer a high potential to automatically detect suspicious occurrences and dangerous or threatening situations on patrol. In order to explore this potential, the scene of interest is recorded first on a reference tour representing the 'everything okay' situation. On further patrols changes are detected with respect to the reference in a two step processing scheme. In the first step, an image retrieval is done to find the reference images that are closest to the current camera image on patrol. This is done efficiently based on precalculated image-to-image registrations of the reference by optimizing image overlap in a local reference search (after a global search when that is needed). In the second step, a robust spatio-temporal change detection is performed that widely compensates 3-D parallax according to variations of the camera position. Various results document the performance of the presented approach.

Autonomy and manual operation in a small robotic system for under-vehicle inspections at security checkpoints

NASA Astrophysics Data System (ADS)

Smuda, William; Muench, Paul L.; Gerhart, Grant R.; Moore, Kevin L.

2002-07-01

Unmanned ground vehicle (UGV) technology can be used in a number of ways to assist in counter-terrorism activities. In addition to the conventional uses of tele-operated robots for unexploded ordinance handling and disposal, water cannons and other crowd control devices, robots can also be employed for a host of terrorism deterrence and detection applications. In previous research USU developed a completely autonomous prototype robot for performing under- vehicle inspections in parking areas (ODIS). Testing of this prototype and discussions with the user community indicated that neither the technology nor the users are ready for complete autonomy. In this paper we present a robotic system based on ODIS that balances the users' desire/need for tele- operation with a limited level of autonomy that enhances the performance of the robot. The system can be used by both civilian law enforcement and military police to replace the traditional mirror on a stick system of looking under cars for bombs and contraband.

Design issues for stereo vision systems used on tele-operated robotic platforms

NASA Astrophysics Data System (ADS)

Edmondson, Richard; Vaden, Justin; Hyatt, Brian; Morris, Jim; Pezzaniti, J. Larry; Chenault, David B.; Tchon, Joe; Barnidge, Tracy; Kaufman, Seth; Pettijohn, Brad

2010-02-01

The use of tele-operated Unmanned Ground Vehicles (UGVs) for military uses has grown significantly in recent years with operations in both Iraq and Afghanistan. In both cases the safety of the Soldier or technician performing the mission is improved by the large standoff distances afforded by the use of the UGV, but the full performance capability of the robotic system is not utilized due to insufficient depth perception provided by the standard two dimensional video system, causing the operator to slow the mission to ensure the safety of the UGV given the uncertainty of the perceived scene using 2D. To address this Polaris Sensor Technologies has developed, in a series of developments funded by the Leonard Wood Institute at Ft. Leonard Wood, MO, a prototype Stereo Vision Upgrade (SVU) Kit for the Foster-Miller TALON IV robot which provides the operator with improved depth perception and situational awareness, allowing for shorter mission times and higher success rates. Because there are multiple 2D cameras being replaced by stereo camera systems in the SVU Kit, and because the needs of the camera systems for each phase of a mission vary, there are a number of tradeoffs and design choices that must be made in developing such a system for robotic tele-operation. Additionally, human factors design criteria drive optical parameters of the camera systems which must be matched to the display system being used. The problem space for such an upgrade kit will be defined, and the choices made in the development of this particular SVU Kit will be discussed.

Architecture for autonomy

NASA Astrophysics Data System (ADS)

Broten, Gregory S.; Monckton, Simon P.; Collier, Jack; Giesbrecht, Jared

2006-05-01

In 2002 Defence R&D Canada changed research direction from pure tele-operated land vehicles to general autonomy for land, air, and sea craft. The unique constraints of the military environment coupled with the complexity of autonomous systems drove DRDC to carefully plan a research and development infrastructure that would provide state of the art tools without restricting research scope. DRDC's long term objectives for its autonomy program address disparate unmanned ground vehicle (UGV), unattended ground sensor (UGS), air (UAV), and subsea and surface (UUV and USV) vehicles operating together with minimal human oversight. Individually, these systems will range in complexity from simple reconnaissance mini-UAVs streaming video to sophisticated autonomous combat UGVs exploiting embedded and remote sensing. Together, these systems can provide low risk, long endurance, battlefield services assuming they can communicate and cooperate with manned and unmanned systems. A key enabling technology for this new research is a software architecture capable of meeting both DRDC's current and future requirements. DRDC built upon recent advances in the computing science field while developing its software architecture know as the Architecture for Autonomy (AFA). Although a well established practice in computing science, frameworks have only recently entered common use by unmanned vehicles. For industry and government, the complexity, cost, and time to re-implement stable systems often exceeds the perceived benefits of adopting a modern software infrastructure. Thus, most persevere with legacy software, adapting and modifying software when and wherever possible or necessary -- adopting strategic software frameworks only when no justifiable legacy exists. Conversely, academic programs with short one or two year projects frequently exploit strategic software frameworks but with little enduring impact. The open-source movement radically changes this picture. Academic frameworks, open to public scrutiny and modification, now rival commercial frameworks in both quality and economic impact. Further, industry now realizes that open source frameworks can reduce cost and risk of systems engineering. This paper describes the Architecture for Autonomy implemented by DRDC and how this architecture meets DRDC's current needs. It also presents an argument for why this architecture should also satisfy DRDC's future requirements as well.

NAVIS-An UGV Indoor Positioning System Using Laser Scan Matching for Large-Area Real-Time Applications

PubMed Central

Tang, Jian.; Chen, Yuwei.; Jaakkola, Anttoni.; Liu, Jinbing.; Hyyppä, Juha.; Hyyppä, Hannu.

2014-01-01

Laser scan matching with grid-based maps is a promising tool for real-time indoor positioning of mobile Unmanned Ground Vehicles (UGVs). While there are critical implementation problems, such as the ability to estimate the position by sensing the unknown indoor environment with sufficient accuracy and low enough latency for stable vehicle control, further development work is necessary. Unfortunately, most of the existing methods employ heuristics for quick positioning in which numerous accumulated errors easily lead to loss of positioning accuracy. This severely restricts its applications in large areas and over lengthy periods of time. This paper introduces an efficient real-time mobile UGV indoor positioning system for large-area applications using laser scan matching with an improved probabilistically-motivated Maximum Likelihood Estimation (IMLE) algorithm, which is based on a multi-resolution patch-divided grid likelihood map. Compared with traditional methods, the improvements embodied in IMLE include: (a) Iterative Closed Point (ICP) preprocessing, which adaptively decreases the search scope; (b) a totally brute search matching method on multi-resolution map layers, based on the likelihood value between current laser scan and the grid map within refined search scope, adopted to obtain the global optimum position at each scan matching; and (c) a patch-divided likelihood map supporting a large indoor area. A UGV platform called NAVIS was designed, manufactured, and tested based on a low-cost robot integrating a LiDAR and an odometer sensor to verify the IMLE algorithm. A series of experiments based on simulated data and field tests with NAVIS proved that the proposed IMEL algorithm is a better way to perform local scan matching that can offer a quick and stable positioning solution with high accuracy so it can be part of a large area localization/mapping, application. The NAVIS platform can reach an updating rate of 12 Hz in a feature-rich environment and 2 Hz even in a feature-poor environment, respectively. Therefore, it can be utilized in a real-time application. PMID:24999715

INS/GPS/LiDAR Integrated Navigation System for Urban and Indoor Environments Using Hybrid Scan Matching Algorithm

PubMed Central

Gao, Yanbin; Liu, Shifei; Atia, Mohamed M.; Noureldin, Aboelmagd

2015-01-01

This paper takes advantage of the complementary characteristics of Global Positioning System (GPS) and Light Detection and Ranging (LiDAR) to provide periodic corrections to Inertial Navigation System (INS) alternatively in different environmental conditions. In open sky, where GPS signals are available and LiDAR measurements are sparse, GPS is integrated with INS. Meanwhile, in confined outdoor environments and indoors, where GPS is unreliable or unavailable and LiDAR measurements are rich, LiDAR replaces GPS to integrate with INS. This paper also proposes an innovative hybrid scan matching algorithm that combines the feature-based scan matching method and Iterative Closest Point (ICP) based scan matching method. The algorithm can work and transit between two modes depending on the number of matched line features over two scans, thus achieving efficiency and robustness concurrently. Two integration schemes of INS and LiDAR with hybrid scan matching algorithm are implemented and compared. Real experiments are performed on an Unmanned Ground Vehicle (UGV) for both outdoor and indoor environments. Experimental results show that the multi-sensor integrated system can remain sub-meter navigation accuracy during the whole trajectory. PMID:26389906

INS/GPS/LiDAR Integrated Navigation System for Urban and Indoor Environments Using Hybrid Scan Matching Algorithm.

PubMed

Gao, Yanbin; Liu, Shifei; Atia, Mohamed M; Noureldin, Aboelmagd

2015-09-15

This paper takes advantage of the complementary characteristics of Global Positioning System (GPS) and Light Detection and Ranging (LiDAR) to provide periodic corrections to Inertial Navigation System (INS) alternatively in different environmental conditions. In open sky, where GPS signals are available and LiDAR measurements are sparse, GPS is integrated with INS. Meanwhile, in confined outdoor environments and indoors, where GPS is unreliable or unavailable and LiDAR measurements are rich, LiDAR replaces GPS to integrate with INS. This paper also proposes an innovative hybrid scan matching algorithm that combines the feature-based scan matching method and Iterative Closest Point (ICP) based scan matching method. The algorithm can work and transit between two modes depending on the number of matched line features over two scans, thus achieving efficiency and robustness concurrently. Two integration schemes of INS and LiDAR with hybrid scan matching algorithm are implemented and compared. Real experiments are performed on an Unmanned Ground Vehicle (UGV) for both outdoor and indoor environments. Experimental results show that the multi-sensor integrated system can remain sub-meter navigation accuracy during the whole trajectory.

ODIS the under-vehicle inspection robot: development status update

NASA Astrophysics Data System (ADS)

Freiburger, Lonnie A.; Smuda, William; Karlsen, Robert E.; Lakshmanan, Sridhar; Ma, Bing

2003-09-01

Unmanned ground vehicle (UGV) technology can be used in a number of ways to assist in counter-terrorism activities. Robots can be employed for a host of terrorism deterrence and detection applications. As reported in last year's Aerosense conference, the U.S. Army Tank Automotive Research, Development and Engineering Center (TARDEC) and Utah State University (USU) have developed a tele-operated robot called ODIS (Omnidirectional Inspection System) that is particularly effective in performing under-vehicle inspections at security checkpoints. ODIS' continuing development for this task is heavily influenced by feedback received from soldiers and civilian law enforcement personnel using ODIS-prototypes in an operational environment. Our goal is to convince civilian law enforcement and military police to replace the traditional "mirror on a stick" system of looking under cars for bombs and contraband with ODIS. This paper reports our efforts in the past one year in terms of optimizing ODIS for the visual inspection task. Of particular concern is the design of the vision system. This paper documents details on the various issues relating to ODIS' vision system - sensor, lighting, image processing, and display.

Water Detection Based on Color Variation

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.

2012-01-01

This software has been designed to detect water bodies that are out in the open on cross-country terrain at close range (out to 30 meters), using imagery acquired from a stereo pair of color cameras mounted on a terrestrial, unmanned ground vehicle (UGV). This detector exploits the fact that the color variation across water bodies is generally larger and more uniform than that of other naturally occurring types of terrain, such as soil and vegetation. Non-traversable water bodies, such as large puddles, ponds, and lakes, are detected based on color variation, image intensity variance, image intensity gradient, size, and shape. At ranges beyond 20 meters, water bodies out in the open can be indirectly detected by detecting reflections of the sky below the horizon in color imagery. But at closer range, the color coming out of a water body dominates sky reflections, and the water cue from sky reflections is of marginal use. Since there may be times during UGV autonomous navigation when a water body does not come into a perception system s field of view until it is at close range, the ability to detect water bodies at close range is critical. Factors that influence the perceived color of a water body at close range are the amount and type of sediment in the water, the water s depth, and the angle of incidence to the water body. Developing a single model of the mixture ratio of light reflected off the water surface (to the camera) to light coming out of the water body (to the camera) for all water bodies would be fairly difficult. Instead, this software detects close water bodies based on local terrain features and the natural, uniform change in color that occurs across the surface from the leading edge to the trailing edge.

Multiagent pursuit-evasion games: Algorithms and experiments

NASA Astrophysics Data System (ADS)

Kim, Hyounjin

Deployment of intelligent agents has been made possible through advances in control software, microprocessors, sensor/actuator technology, communication technology, and artificial intelligence. Intelligent agents now play important roles in many applications where human operation is too dangerous or inefficient. There is little doubt that the world of the future will be filled with intelligent robotic agents employed to autonomously perform tasks, or embedded in systems all around us, extending our capabilities to perceive, reason and act, and replacing human efforts. There are numerous real-world applications in which a single autonomous agent is not suitable and multiple agents are required. However, after years of active research in multi-agent systems, current technology is still far from achieving many of these real-world applications. Here, we consider the problem of deploying a team of unmanned ground vehicles (UGV) and unmanned aerial vehicles (UAV) to pursue a second team of UGV evaders while concurrently building a map in an unknown environment. This pursuit-evasion game encompasses many of the challenging issues that arise in operations using intelligent multi-agent systems. We cast the problem in a probabilistic game theoretic framework and consider two computationally feasible pursuit policies: greedy and global-max. We also formulate this probabilistic pursuit-evasion game as a partially observable Markov decision process and employ a policy search algorithm to obtain a good pursuit policy from a restricted class of policies. The estimated value of this policy is guaranteed to be uniformly close to the optimal value in the given policy class under mild conditions. To implement this scenario on real UAVs and UGVs, we propose a distributed hierarchical hybrid system architecture which emphasizes the autonomy of each agent yet allows for coordinated team efforts. We then describe our implementation on a fleet of UGVs and UAVs, detailing components such as high level pursuit policy computation, inter-agent communication, navigation, sensing, and regulation. We present both simulation and experimental results on real pursuit-evasion games between our fleet of UAVs and UGVs and evaluate the pursuit policies, relating expected capture times to the speed and intelligence of the evaders and the sensing capabilities of the pursuers. The architecture and algorithmsis described in this dissertation are general enough to be applied to many real-world applications.

Additive Manufacturing of Parts and Tooling in Robotic Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Love, Lonnie J.; Hassen, Ahmed A.; Chesser, Phillip C.

ORNL worked with Transcend Robotics, LLC to explore additive manufacturing of the two-piece compression body for their ARTI mobile robot platform. Extrusion compression molding was identified as an effective means of manufacturing these parts. ORNL consulted on modifications to the housing design to accommodate the selected manufacturing process. Parts were printed using ORNL's FDM machines for testing and evaluation of the design as a precursor to molding the parts. The assembly and evaluation of the parts proved favorable and minor design changes to improve assembly and performance were identified.The goal is to develop a light weight and rugged two-part roboticmore » enclosure for an unmanned ground vehicle UGV) that will be used in search and rescue applications. The FDM parts fabricated by ORNL allowed Transcend Robotics to assemble a prototype robot and verify that the new parts will meet the performance requirements. ORNL fabricated enclosure parts out of ABS and Nylon 12 materials such that the design could be tested prior to fabricating tooling for compression molding of Nylon 6 with carbon fiber fill. The robot was performance tested and compared with the previous manufacturing techniques and found to have superior performance.« less

LABRADOR: a learning autonomous behavior-based robot for adaptive detection and object retrieval

NASA Astrophysics Data System (ADS)

Yamauchi, Brian; Moseley, Mark; Brookshire, Jonathan

2013-01-01

As part of the TARDEC-funded CANINE (Cooperative Autonomous Navigation in a Networked Environment) Program, iRobot developed LABRADOR (Learning Autonomous Behavior-based Robot for Adaptive Detection and Object Retrieval). LABRADOR was based on the rugged, man-portable, iRobot PackBot unmanned ground vehicle (UGV) equipped with an explosives ordnance disposal (EOD) manipulator arm and a custom gripper. For LABRADOR, we developed a vision-based object learning and recognition system that combined a TLD (track-learn-detect) filter based on object shape features with a color-histogram-based object detector. Our vision system was able to learn in real-time to recognize objects presented to the robot. We also implemented a waypoint navigation system based on fused GPS, IMU (inertial measurement unit), and odometry data. We used this navigation capability to implement autonomous behaviors capable of searching a specified area using a variety of robust coverage strategies - including outward spiral, random bounce, random waypoint, and perimeter following behaviors. While the full system was not integrated in time to compete in the CANINE competition event, we developed useful perception, navigation, and behavior capabilities that may be applied to future autonomous robot systems.

Development of a Geospatial Data-Sharing Method for Unmanned Vehicles Based on the Joint Architecture for Unmanned Systems (JAUS)

DTIC Science & Technology

2005-08-01

the Office of the Secretary of Defense chartered the Joint Architecture for Unmanned Ground Systems ( JAUGS ) Working Group to address these concerns...The JAUGS Working Group was tasked with developing an initial standard for interoperable unmanned ground systems. In 2002, the charter of the... JAUGS Working Group was 1 2 modified such that their efforts would extend to all unmanned systems, not only ground systems. The standard was

A survey of unmanned ground vehicles with applications to agricultural and environmental sensing

NASA Astrophysics Data System (ADS)

Bonadies, Stephanie; Lefcourt, Alan; Gadsden, S. Andrew

2016-05-01

Unmanned ground vehicles have been utilized in the last few decades in an effort to increase the efficiency of agriculture, in particular, by reducing labor needs. Unmanned vehicles have been used for a variety of purposes including: soil sampling, irrigation management, precision spraying, mechanical weeding, and crop harvesting. In this paper, unmanned ground vehicles, implemented by researchers or commercial operations, are characterized through a comparison to other vehicles used in agriculture, namely airplanes and UAVs. An overview of different trade-offs of configurations, control schemes, and data collection technologies is provided. Emphasis is given to the use of unmanned ground vehicles in food crops, and includes a discussion of environmental impacts and economics. Factors considered regarding the future trends and potential issues of unmanned ground vehicles include development, management and performance. Also included is a strategy to demonstrate to farmers the safety and profitability of implementing the technology.

Augmented reality user interface for mobile ground robots with manipulator arms

NASA Astrophysics Data System (ADS)

Vozar, Steven; Tilbury, Dawn M.

2011-01-01

Augmented Reality (AR) is a technology in which real-world visual data is combined with an overlay of computer graphics, enhancing the original feed. AR is an attractive tool for teleoperated UGV UIs as it can improve communication between robots and users via an intuitive spatial and visual dialogue, thereby increasing operator situational awareness. The successful operation of UGVs often relies upon both chassis navigation and manipulator arm control, and since existing literature usually focuses on one task or the other, there is a gap in mobile robot UIs that take advantage of AR for both applications. This work describes the development and analysis of an AR UI system for a UGV with an attached manipulator arm. The system supplements a video feed shown to an operator with information about geometric relationships within the robot task space to improve the operator's situational awareness. Previous studies on AR systems and preliminary analyses indicate that such an implementation of AR for a mobile robot with a manipulator arm is anticipated to improve operator performance. A full user-study can determine if this hypothesis is supported by performing an analysis of variance on common test metrics associated with UGV teleoperation.

Investigations into near-real-time surveying for geophysical data collection using an autonomous ground vehicle

USGS Publications Warehouse

Phelps, Geoffrey A.; Ippolito, C.; Lee, R.; Spritzer, R.; Yeh, Y.

2014-01-01

The U.S. Geological Survey and the National Aeronautics and Space Administration are cooperatively investigating the utility of unmanned vehicles for near-real-time autonomous surveys of geophysical data collection. Initially focused on unmanned ground vehicle collection of magnetic data, this cooperative effort has brought unmanned surveying, precision guidance, near-real-time communication, on-the-fly data processing, and near-real-time data interpretation into the realm of ground geophysical surveying, all of which offer advantages over current methods of manned collection of ground magnetic data. An unmanned ground vehicle mission has demonstrated that these vehicles can successfully complete missions to collect geophysical data, and add advantages in data collection, processing, and interpretation. We view the current experiment as an initial phase in further unmanned vehicle data-collection missions, including aerial surveying.

Field experiments using SPEAR: a speech control system for UGVs

NASA Astrophysics Data System (ADS)

Chhatpar, Siddharth R.; Blanco, Chris; Czerniak, Jeffrey; Hoffman, Orin; Juneja, Amit; Pruthi, Tarun; Liu, Dongqing; Karlsen, Robert; Brown, Jonathan

2009-05-01

This paper reports on a Field Experiment carried out by the Human Research and Engineering Directorate at Ft. Benning to evaluate the efficacy of using speech to control an Unmanned Ground Vehicle (UGV) concurrently with a handcontroller. The SPEAR system, developed by Think-A-Move, provides speech-control of UGVs. The system picks up user-speech in the ear canal with an in-ear microphone. This property allows it to work efficiently in high-noise environments, where traditional speech systems, employing external microphones, fail. It has been integrated with an iRobot PackBot 510 with EOD kit. The integrated system allows the hand-controller to be supplemented with speech for concurrent control. At Ft. Benning, the integrated system was tested by soldiers from the Officer Candidate School. The Experiment had dual focus: 1) Quantitative measurement of the time taken to complete each station and the cognitive load on users; 2) Qualitative evaluation of ease-of-use and ergonomics through soldier-feedback. Also of significant benefit to Think-A-Move was soldier-feedback on the speech-command vocabulary employed: What spoken commands are intuitive, and how the commands should be executed, e.g., limited-motion vs. unlimited-motion commands. Overall results from the Experiment are reported in the paper.

TALON: a universal unmanned ground vehicle platform, enabling the mission to be the focus

NASA Astrophysics Data System (ADS)

Wells, Peter; Deguire, Dan

2005-05-01

Foster-Miller's unmanned ground vehicle, TALON, was originally developed under DARPA's Tactical Mobile Robotics (TMR) program. TALON has evolved over the years and has proven to be a robust, mobile, universal platform. As a result of the advances made in the evolution of TALON, new and far-reaching opportunities have been realized for unmanned ground vehicles. In recent conflicts such as in Afghanistan and Iraq, unmanned systems have played an important role and have extended the reach and capabilities of the War fighter. Technological advances have transformed unmanned vehicles in to useful tools and in some cases are used in lieu of sending in a soldier. Unmanned ground vehicles have seen recent and persistent success, as shown in theater, in the explosive ordinance disposal (EOD) and improvised ordinance disposal (IED) missions. Foster-Miller's TALON has experienced over ten thousand EOD and IED missions in Iraq alone. The success of the unmanned system has resulted in the doctrine "Send the robot in first". Foster-Miller has taken the role of the unmanned vehicle in yet another direction. Foster-Miller has transformed the TALON from a "practical" to "tactical" system. Through the combined efforts of Foster-Miller and the US Army, TALON has been involved in a weaponization program. To date, Foster-Miller has outfitted the TALON with 11 systems. As one can see, the unmanned ground vehicle is much more than a mobility platform.

LiDAR Scan Matching Aided Inertial Navigation System in GNSS-Denied Environments.

PubMed

Tang, Jian; Chen, Yuwei; Niu, Xiaoji; Wang, Li; Chen, Liang; Liu, Jingbin; Shi, Chuang; Hyyppä, Juha

2015-07-10

A new scan that matches an aided Inertial Navigation System (INS) with a low-cost LiDAR is proposed as an alternative to GNSS-based navigation systems in GNSS-degraded or -denied environments such as indoor areas, dense forests, or urban canyons. In these areas, INS-based Dead Reckoning (DR) and Simultaneous Localization and Mapping (SLAM) technologies are normally used to estimate positions as separate tools. However, there are critical implementation problems with each standalone system. The drift errors of velocity, position, and heading angles in an INS will accumulate over time, and on-line calibration is a must for sustaining positioning accuracy. SLAM performance is poor in featureless environments where the matching errors can significantly increase. Each standalone positioning method cannot offer a sustainable navigation solution with acceptable accuracy. This paper integrates two complementary technologies-INS and LiDAR SLAM-into one navigation frame with a loosely coupled Extended Kalman Filter (EKF) to use the advantages and overcome the drawbacks of each system to establish a stable long-term navigation process. Static and dynamic field tests were carried out with a self-developed Unmanned Ground Vehicle (UGV) platform-NAVIS. The results prove that the proposed approach can provide positioning accuracy at the centimetre level for long-term operations, even in a featureless indoor environment.

LiDAR Scan Matching Aided Inertial Navigation System in GNSS-Denied Environments

PubMed Central

Tang, Jian; Chen, Yuwei; Niu, Xiaoji; Wang, Li; Chen, Liang; Liu, Jingbin; Shi, Chuang; Hyyppä, Juha

2015-01-01

A new scan that matches an aided Inertial Navigation System (INS) with a low-cost LiDAR is proposed as an alternative to GNSS-based navigation systems in GNSS-degraded or -denied environments such as indoor areas, dense forests, or urban canyons. In these areas, INS-based Dead Reckoning (DR) and Simultaneous Localization and Mapping (SLAM) technologies are normally used to estimate positions as separate tools. However, there are critical implementation problems with each standalone system. The drift errors of velocity, position, and heading angles in an INS will accumulate over time, and on-line calibration is a must for sustaining positioning accuracy. SLAM performance is poor in featureless environments where the matching errors can significantly increase. Each standalone positioning method cannot offer a sustainable navigation solution with acceptable accuracy. This paper integrates two complementary technologies—INS and LiDAR SLAM—into one navigation frame with a loosely coupled Extended Kalman Filter (EKF) to use the advantages and overcome the drawbacks of each system to establish a stable long-term navigation process. Static and dynamic field tests were carried out with a self-developed Unmanned Ground Vehicle (UGV) platform—NAVIS. The results prove that the proposed approach can provide positioning accuracy at the centimetre level for long-term operations, even in a featureless indoor environment. PMID:26184206

The Ground Control Room as an Enabling Technology in the Unmanned Aerial System

NASA Technical Reports Server (NTRS)

Gear, Gary; Mace, Thomas

2007-01-01

This viewgraph presentation reviews the development of the ground control room as an required technology for the use of an Unmanned Aerial system. The Unmanned Aerial system is a strategic component of the Global Observing System, which will serve global science needs. The unmanned aerial system will use the same airspace as manned aircraft, therefore there will be unique telemetry needs.

Single-Frame Terrain Mapping Software for Robotic Vehicles

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.

2011-01-01

This software is a component in an unmanned ground vehicle (UGV) perception system that builds compact, single-frame terrain maps for distribution to other systems, such as a world model or an operator control unit, over a local area network (LAN). Each cell in the map encodes an elevation value, terrain classification, object classification, terrain traversability, terrain roughness, and a confidence value into four bytes of memory. The input to this software component is a range image (from a lidar or stereo vision system), and optionally a terrain classification image and an object classification image, both registered to the range image. The single-frame terrain map generates estimates of the support surface elevation, ground cover elevation, and minimum canopy elevation; generates terrain traversability cost; detects low overhangs and high-density obstacles; and can perform geometry-based terrain classification (ground, ground cover, unknown). A new origin is automatically selected for each single-frame terrain map in global coordinates such that it coincides with the corner of a world map cell. That way, single-frame terrain maps correctly line up with the world map, facilitating the merging of map data into the world map. Instead of using 32 bits to store the floating-point elevation for a map cell, the vehicle elevation is assigned to the map origin elevation and reports the change in elevation (from the origin elevation) in terms of the number of discrete steps. The single-frame terrain map elevation resolution is 2 cm. At that resolution, terrain elevation from 20.5 to 20.5 m (with respect to the vehicle's elevation) is encoded into 11 bits. For each four-byte map cell, bits are assigned to encode elevation, terrain roughness, terrain classification, object classification, terrain traversability cost, and a confidence value. The vehicle s current position and orientation, the map origin, and the map cell resolution are all included in a header for each map. The map is compressed into a vector prior to delivery to another system.

Strategies for the Interpretive Integration of Ground and Aerial Views in UGV Operations

DTIC Science & Technology

2006-11-01

conjoinment of the psychological processes and effects of perception, object recognition (i.e. Biederman & Gerhardstein, 1993), navigation (Wickens...rather simple geon structural descriptions (GSD, see Biederman & 4 Gerhardstein, 1993). A geon is a basic three dimensional solid shape, such as a...large and reliable sex difference. Behavioral Brain Research, 93, 185-190. Biederman , I., & Gerhardstein, C. (1993). Recognizing depth- rotated objects

The development of ground unmanned vehicles, driver assistance systems and components according to patent publications

NASA Astrophysics Data System (ADS)

Saykin, A. M.; Tuktakiev, G. S.; Zhuravlev, A. V.; Zaitseva, E. P.

2018-02-01

The paper contains the analysis of the main trends in the patenting of ground unmanned vehicles, driver assistance systems (ADAS) and unmanned vehicle components abroad during the period from 2010 to 2016. The conclusion was made that the intensity of their patenting abroad increased.

A survey of unmanned ground vehicles with applications to agricultural and environmental sensing

USDA-ARS?s Scientific Manuscript database

Unmanned ground vehicles have been utilized in the last few decades in an effort to increase the efficiency of agriculture, in particular, by reducing labor needs. Unmanned vehicles have been used for a variety of purposes including: soil sampling, irrigation management, precision spraying, mechanic...

Strong contributions of local background climate to the cooling effect of urban green vegetation.

PubMed

Yu, Zhaowu; Xu, Shaobin; Zhang, Yuhan; Jørgensen, Gertrud; Vejre, Henrik

2018-05-01

Utilization of urban green vegetation (UGV) has been recognized as a promising option to mitigate urban heat island (UHI) effect. While we still lack understanding of the contributions of local background climate to the cooling effect of UGV. Here we proposed and employed a cooling effect framework and selected eight typical cities located in Temperate Monsoon Climate (TMC) and Mediterranean Climate (MC) demonstrate that local climate condition largely affects the cooling effect of UGV. Specifically, we found increasing (artificial) rainfall and irrigation contribute to improving the cooling intensity of grassland in both climates, particularly in the hot-dry environment. The cities with high relative humidity would restrict the cooling effect of UGV. Increasing wind speed would significantly enhance the tree-covered while weakening the grass-covered UGVs' cooling effect in MC cities. We also identified that, in order to achieve the most effective cooling with the smallest sized tree-covered UGV, the area of trees in both climate zones' cities should generally be planned around 0.5 ha. The method and results enhance understanding of the cooling effect of UGVs on larger (climate) scales and provide important insights for UGV planning and management.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oppel III, Fred J.; Rigdon, James Brian; Gottlieb, Eric Joseph

This package contains, for the most part, the base classes and interfaces for vehicles and characters. Originally everything was in UGV, but things were split out to simplify the design since the assertion of UGV1.0. Modules in UGV, UWV, and UAV will inherit from classes in this package. There is also a high-level system that is a base class for systems in UGV, UWV, and UAV.

Manned-Unmanned Teaming of Aircraft - Literature Search

DTIC Science & Technology

2013-12-01

unmanned aircraft reconnaissance system MQ 8B Fire Scout vertical takeoff and landing unmanned system MQ 5B Hunter medium altitude unmanned aerial...201140, and allows their crew to view sensor data from unmanned aircraft systems (UAS) and send data from the helicopter’s sensors to the ground.35 No...Helicopter, AAI unmanned Aircraft Systems , and Textron Inc. It opened in December 2012 in Huntsville Alabama. It will enable “a software and

Advocates and critics for tactical behaviors in UGV navigation

NASA Astrophysics Data System (ADS)

Hussain, Talib S.; Vidaver, Gordon; Berliner, Jeffrey

2005-05-01

Critical to the development of unmanned ground vehicle platforms is the incorporation of adaptive tactical behaviors for the planning of high-level navigation and tactical actions. BBN Technologies recently completed a simulation-based project for the Army Research Lab (ARL) in which we applied an evolutionary computation approach to navigating through a terrain to capture flag objectives while faced with one or more mobile enemies. Our Advocates and Critics for Tactical Behaviors (ACTB) system evolves plans for the vehicle that control its movement goals (in the form of waypoints), and its future actions (e.g., pointing cameras). We apply domain-specific, state-dependent genetic operators called advocates that promote specific tactical behaviors (e.g., adapt a plan to stay closer to walls). We define the fitness function as a weighted sum of a number of independent, domain-specific, state-dependent evaluation components called critics. Critics reward plans based upon specific tactical criteria, such as minimizing risk of exposure or time to the flags. Additionally, the ACTB system provides the capability for a human commander to specify the "rules of engagement" under which the vehicle will operate. The rules of engagement determine the planning emphasis required under different tactical situations (e.g., discovery of an enemy), and provide a mechanism for automatically adapting the relative selection probabilities of the advocates, the weights of the critics, and the depth of planning in response to tactical events. The ACTB system demonstrated highly effective performance in a head-to-head testing event, held by ARL, against two competing tactical behavior systems.

Modeling and Simulation of an Unmanned Ground Vehicle Power System

DTIC Science & Technology

2014-08-07

Modeling and Simulation of an Unmanned Ground Vehicle Power System John Broderick Jack Hartner Dawn Tilbury Ella Atkins Sponsored by U.S...5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) John Broderick ; Jack Hartner; Dawn Tilbury; Ella Atkins 5d. PROJECT

Navigation and Hazard Avoidance for High-Speed Unmanned Ground Vehicles in Rough Terrain

DTIC Science & Technology

2008-07-07

Potential Field Navigation of High Speed Vehicles on Rough Terrain,” Robotica , Vol. 25, No. 4, pp 409-424, July 2007 Udengaard, M., and Iagnemma, K...Navigation of Unmanned Ground Vehicles on Uneven Terrain using Potential Fields," to appear in Robotica , 2007 [16] Spenko, M., Kuroda, Y., Dubowsky, S

Discrete Event Command & Control for Networked Teams with Multiple Missions

DTIC Science & Technology

2009-03-16

Architecture for Unmanned Ground Systems ( JAUGS )10, and is an efficient means to realize the high-level OODA loops (observe, orient, decide, act) of 4D...for Unmanned Ground systems ( JAUGS )10, and is an efficient means to realize the OODA loops (observe, orient, decide, act) of 4D/RCS11. DEC is able to

Surveillance of ground vehicles for airport security

NASA Astrophysics Data System (ADS)

Blasch, Erik; Wang, Zhonghai; Shen, Dan; Ling, Haibin; Chen, Genshe

2014-06-01

Future surveillance systems will work in complex and cluttered environments which require systems engineering solutions for such applications such as airport ground surface management. In this paper, we highlight the use of a L1 video tracker for monitoring activities at an airport. We present methods of information fusion, entity detection, and activity analysis using airport videos for runway detection and airport terminal events. For coordinated airport security, automated ground surveillance enhances efficient and safe maneuvers for aircraft, unmanned air vehicles (UAVs) and unmanned ground vehicles (UGVs) operating within airport environments.

Current Thrusts in Ground Robotics: Programs, Systems, Technologies, Issues

DTIC Science & Technology

2000-03-01

MPRS – Demo III – MDARS-E and MDARS-I – JAUGS SPAWAR Systems Center, San Diego San Diego CA 92152-7383 Basic UXO Gathering System (BUGS) Use tens of...processing resources • Modularity improves sensor fusion for alarms and alerts • Joint Architecture for Unmanned Ground Systems ( JAUGS ) SPAWAR Systems...pp lic at io ns 1996 1998 2000 2002 SPAWAR Systems Center, San Diego San Diego CA 92152-7383 JAUGS : Joint Architecture for Unmanned Ground Systems

Capabilities Assessment and Employment Recommendations for Full Motion Video Optical Navigation Exploitation (FMV-ONE)

DTIC Science & Technology

2015-06-01

GEOINT geospatial intelligence GFC ground force commander GPS global positioning system GUI graphical user interface HA/DR humanitarian...transport stream UAS unmanned aerial system . See UAV. UAV unmanned aerial vehicle. See UAS. VM virtual machine VMU Marine Unmanned Aerial Vehicle... Unmanned Air Systems (UASs). Current programs promise to dramatically increase the number of FMV feeds in the near future. However, there are too

Small UGV platforms for unattended sensors

NASA Astrophysics Data System (ADS)

Smuda, Bill; Gerhart, Grant

2005-10-01

The wars in Iraq and Afghanistan have shown the importance of sensor and robotic technology as a force multiplier and a tool for moving soldiers out of harms way. Situations on the ground make soldiers easy targets for snipers and suicide bombers. Sensors and robotics technology reduces risk to soldiers and other personnel at checkpoints, in access areas and on convoy routes. Early user involvement in innovative and aggressive acquisition and development strategies are the key to moving sensor and robotic and associated technology into the hands of the user, the soldier on the ground. This paper discusses activity associated with rapid development of the robotics, sensors and our field experience with robotics in Iraq and Afghanistan.

Intelligent unmanned vehicle systems suitable for individual or cooperative missions

NASA Astrophysics Data System (ADS)

Anderson, Matthew O.; McKay, Mark D.; Wadsworth, Derek C.

2007-04-01

The Department of Energy's Idaho National Laboratory (INL) has been researching autonomous unmanned vehicle systems for over fifteen years. Areas of research have included unmanned ground and aerial vehicles used for hazardous and remote operations as well as teamed together for advanced payloads and mission execution. Areas of application include aerial particulate sampling, cooperative remote radiological sampling, and persistent surveillance including real-time mosaic and geo-referenced imagery in addition to high-resolution still imagery. Both fixed-wing and rotary airframes are used possessing capabilities spanning remote control to fully autonomous operation. Patented INL-developed auto steering technology is taken advantage of to provide autonomous parallel path swathing with either manned or unmanned ground vehicles. Aerial look-ahead imagery is utilized to provide a common operating picture for the ground and air vehicles during cooperative missions. This paper will discuss the various robotic vehicles, including sensor integration, used to achieve these missions and anticipated cost and labor savings.

Developing an Adaptable NextGen Interface for the UAS Ground Control Station

NASA Technical Reports Server (NTRS)

Murphy, James R.; Otto, Neil; Jovic, Srba; Carniol, Ted; Kotegawa, Tatsuya

2016-01-01

Presently a significant number of unmanned aircraft are not included in the existing National Airspace System surveillance system. This is due to many reasons including an inability to carry Automatic Dependent Surveillance Broadcast equipment for weight or power consumption deficiencies, legacy equipment usage, and the experimental nature of unmanned aircraft. In addition, pilots on the ground do not have the situation awareness to proximal aircraft pilots in the cockpit have. However, many unmanned aircraft utilize a link between the aircraft and ground control station that includes periodic updates to the aircraft position. Technologies have been developed to provide the existing national surveillance system with the location of the aircraft while at the same time providing the ground pilot a display with aircraft that are in the aircrafts proximity, thus expanding the national surveillance data as well as provide increased pilot situation awareness.

Mobile detection assessment and response systems (MDARS): a force protection physical security operational success

NASA Astrophysics Data System (ADS)

Shoop, Brian; Johnston, Michael; Goehring, Richard; Moneyhun, Jon; Skibba, Brian

2006-05-01

MDARS is a Semi-autonomous unmanned ground vehicle with intrusion detection & assessment, product & barrier assessment payloads. Its functions include surveillance, security, early warning, incident first response and product and barrier status primarily focused on a depot/munitions security mission at structured/semi-structured facilities. MDARS is in Systems Development and Demonstration (SDD) under the Product Manager for Force Protection Systems (PM-FPS). MDARS capabilities include semi-autonomous navigation, obstacle avoidance, motion detection, day and night imagers, radio frequency tag inventory/barrier assessment and audio challenge and response. Four SDD MDARS Patrol Vehicles have been undergoing operational evaluation at Hawthorne Army Depot, NV (HWAD) since October 2004. Hawthorne personnel were trained to administer, operate and maintain the system in accordance with the US Army Military Police School (USAMPS) Concept of Employment and the PM-FPS MDARS Integrated Logistic Support Plan. The system was subjected to intensive periods of evaluation under the guidance and control of the Army Test and Evaluation Center (ATEC) and PM-FPS. Significantly, in terms of User acceptance, the system has been under the "operational control" of the installation performing security and force protection missions in support of daily operations. This evaluation is intended to assess MDARS operational effectiveness in an operational environment. Initial observations show that MDARS provides enhanced force protection, can potentially reduce manpower requirements by conducting routine tasks within its design capabilities and reduces Soldier exposure in the initial response to emerging incidents and situations. Success of the MDARS program has been instrumental in the design and development of two additional robotic force protection programs. The first was the USAF Force Protection Battle Lab sponsored Remote Detection Challenge & Response (REDCAR) concept demonstration executed by the Air Force Robotics Lab (AFRL). The REDCAR used an MDARS PUV as the central robotic technology and expanded the concept to incorporate a smaller high speed platform (SCOUT) equipped with lethal, non-lethal and challenge components as an engagement platform and, in a marsupial configuration on the MDARS, a small UGV that can be deployed to investigate close quarters areas. The Family of Integrated Rapid Response Equipment (FIRRE) program further expands these concepts by incorporating and adapting other mobile/tactical force protection equipment with a more robust Unmanned Ground Vehicle into an "Expeditionary" configuration to provide the current force with a rapidly deployable force protection system that can operate in austere less structured and protected environments. A USAMPS/ MANCEN sponsored "FIRRE System Demonstration" in Iraq is scheduled to begin in FY '07.

On-Board Mining in the Sensor Web

NASA Astrophysics Data System (ADS)

Tanner, S.; Conover, H.; Graves, S.; Ramachandran, R.; Rushing, J.

2004-12-01

On-board data mining can contribute to many research and engineering applications, including natural hazard detection and prediction, intelligent sensor control, and the generation of customized data products for direct distribution to users. The ability to mine sensor data in real time can also be a critical component of autonomous operations, supporting deep space missions, unmanned aerial and ground-based vehicles (UAVs, UGVs), and a wide range of sensor meshes, webs and grids. On-board processing is expected to play a significant role in the next generation of NASA, Homeland Security, Department of Defense and civilian programs, providing for greater flexibility and versatility in measurements of physical systems. In addition, the use of UAV and UGV systems is increasing in military, emergency response and industrial applications. As research into the autonomy of these vehicles progresses, especially in fleet or web configurations, the applicability of on-board data mining is expected to increase significantly. Data mining in real time on board sensor platforms presents unique challenges. Most notably, the data to be mined is a continuous stream, rather than a fixed store such as a database. This means that the data mining algorithms must be modified to make only a single pass through the data. In addition, the on-board environment requires real time processing with limited computing resources, thus the algorithms must use fixed and relatively small amounts of processing time and memory. The University of Alabama in Huntsville is developing an innovative processing framework for the on-board data and information environment. The Environment for On-Board Processing (EVE) and the Adaptive On-board Data Processing (AODP) projects serve as proofs-of-concept of advanced information systems for remote sensing platforms. The EVE real-time processing infrastructure will upload, schedule and control the execution of processing plans on board remote sensors. These plans provide capabilities for autonomous data mining, classification and feature extraction using both streaming and buffered data sources. A ground-based testbed provides a heterogeneous, embedded hardware and software environment representing both space-based and ground-based sensor platforms, including wireless sensor mesh architectures. The AODP project explores the EVE concepts in the world of sensor-networks, including ad-hoc networks of small sensor platforms.

Characteristic Model of a Shock Absorber in an Unmanned Ground Vehicle

NASA Astrophysics Data System (ADS)

Danko, Ján; Milesich, Tomáš; Bugár, Martin; Madarás, Juraj

2012-12-01

The paper deals with mathematical models for the shock absorber of an unmanned ground vehicle. The possibility of mathematically modeling the shock absorber is discussed. Specific types of mathematical models are described and the experimental measurement of a shock absorber is made. For modeling the characteristics of the shock absorber the modified Bouc-Wen model (Spencer model) is selected. From the mathematical model, a simulation model in Matlab/Simulink is created. The identification of the Spencer model parameters is performed and force-velocity and force-displacement characteristics of the shock absorber of an unmanned ground vehicle is made. In the conclusions, the simulated characteristics are verified and evaluated by the measured characteristics.

Tank-automotive robotics

NASA Astrophysics Data System (ADS)

Lane, Gerald R.

1999-07-01

To provide an overview of Tank-Automotive Robotics. The briefing will contain program overviews & inter-relationships and technology challenges of TARDEC managed unmanned and robotic ground vehicle programs. Specific emphasis will focus on technology developments/approaches to achieve semi- autonomous operation and inherent chassis mobility features. Programs to be discussed include: DemoIII Experimental Unmanned Vehicle (XUV), Tactical Mobile Robotics (TMR), Intelligent Mobility, Commanders Driver Testbed, Collision Avoidance, International Ground Robotics Competition (ICGRC). Specifically, the paper will discuss unique exterior/outdoor challenges facing the IGRC competing teams and the synergy created between the IGRC and ongoing DoD semi-autonomous Unmanned Ground Vehicle and DoT Intelligent Transportation System programs. Sensor and chassis approaches to meet the IGRC challenges and obstacles will be shown and discussed. Shortfalls in performance to meet the IGRC challenges will be identified.

Science on TeacherTube: A Mixed Methods Analysis of Teacher Produced Video

NASA Astrophysics Data System (ADS)

Chmiel, Margaret (Marjee)

Increased bandwidth, inexpensive video cameras and easy-to-use video editing software have made social media sites featuring user generated video (UGV) an increasingly popular vehicle for online communication. As such, UGV have come to play a role in education, both formal and informal, but there has been little research on this topic in scholarly literature. In this mixed-methods study, a content and discourse analysis are used to describe the most successful UGV in the science channel of an education-focused site called TeacherTube. The analysis finds that state achievement tests, and their focus on vocabulary and recall-level knowledge, drive much of the content found on TeacherTube.

UGV Interoperability Profile (IOP) Communications Profile, Version 0

DTIC Science & Technology

2011-12-21

some UGV systems employ Orthogonal Frequency Division Multiplexing ( OFDM ) or Coded Orthogonal Frequency Division Multiplexing (COFDM) waveforms which...other portions of the IOP. Attribute Paragraph Title Values Waveform 3.3 Air Interface/ Waveform OFDM , COFDM, DDL, CDL, None OCU to Platform...Sight MANET Mobile Ad-hoc Network Mbps Megabits per second MC/PM Master Controller/ Payload Manager MHz Megahertz MIMO Multiple Input Multiple

DoD Comprehensive Military Unmanned Aerial Vehicle Smart Device Ground Control Station Threat Model

DTIC Science & Technology

2015-04-01

design , imple- mentation, and test evaluation were interviewed to evaluate the existing gaps in the DoD processes for cybersecurity. This group exposed...such as antenna design and signal reception have made satellite communication networks a viable solution for smart devices on the battlefield...DoD Comprehensive Military Unmanned AERIAL VEHICLE SMART DEVICE GROUND CONTROL STATION THREAT MODEL  Image designed by Diane Fleischer Report

Tracking with a Cooperatively Controlled Swarm of GMTI Equipped UAVS

DTIC Science & Technology

2008-12-02

with Ground Optimal Placement of GMTI UAVs for ground target tracking Abhijit Sinha°, Thia. Kirubarajana and Yaakov Bar-Shalom6 " Electrical and...Storrs, CT 06269, USA Abstract—With the recent advent of moderate-cost unmanned (or uninhabited) aerial vehicles (UAV) and their success in...the sensor platforms are mobile one has to decide the optimal placement of sensors. With the recent advent of af- fordable unmanned aerial vehicles

Arctic Atmospheric Measurements Using Manned and Unmanned Aircraft, Tethered Balloons, and Ground-Based Systems at U.S. DOE ARM Facilities on the North Slope Of Alaska

NASA Astrophysics Data System (ADS)

Ivey, M.; Dexheimer, D.; Roesler, E. L.; Hillman, B. R.; Hardesty, J. O.

2016-12-01

The U.S. Department of Energy (DOE) provides scientific infrastructure and data to the international Arctic research community via research sites located on the North Slope of Alaska and an open data archive maintained by the ARM program. In 2016, DOE continued investments in improvements to facilities and infrastructure at Oliktok Point Alaska to support operations of ground-based facilities and unmanned aerial systems for science missions in the Arctic. The Third ARM Mobile Facility, AMF3, now deployed at Oliktok Point, was further expanded in 2016. Tethered instrumented balloons were used at Oliktok to make measurements of clouds in the boundary layer including mixed-phase clouds and to compare measurements with those from the ground and from unmanned aircraft operating in the airspace above AMF3. The ARM facility at Oliktok Point includes Special Use Airspace. A Restricted Area, R-2204, is located at Oliktok Point. Roughly 4 miles in diameter, it facilitates operations of tethered balloons and unmanned aircraft. R-2204 and a new Warning Area north of Oliktok, W-220, are managed by Sandia National Laboratories for DOE Office of Science/BER. These Special Use Airspaces have been successfully used to launch and operate unmanned aircraft over the Arctic Ocean and in international airspace north of Oliktok Point.A steady progression towards routine operations of unmanned aircraft and tethered balloon systems continues at Oliktok. Small unmanned aircraft (DataHawks) and tethered balloons were successfully flown at Oliktok starting in June of 2016. This poster will discuss how principal investigators may apply for use of these Special Use Airspaces, acquire data from the Third ARM Mobile Facility, or bring their own instrumentation for deployment at Oliktok Point, Alaska.

Modeling and Simulation of an Unmanned Ground Vehicle Power System

DTIC Science & Technology

2014-03-28

Wilhelm, A. N., Surgenor, B. W., and Pharoah, J. G., “Design and evaluation of a micro-fuel-cell-based power system for a mobile robot,” Mechatronics ... Embedded Control Systems ], Control Engineering, 91–116, Birkhuser Boston (2005). [12] Alur, R., Courcoubetis, C., Halbwachs, N., Henzinger, T., Ho, P.-H...Modeling and Simulation of an Unmanned Ground Vehicle Power System John Brodericka∗, Jack Hartnerb, Dawn Tilburya, and Ella Atkinsa aThe University

Integrated Unmanned Air-Ground Robotics System, Volume 4

DTIC Science & Technology

2001-08-20

3) IPT Integrated Product Team IRP Intermediate Power Rating JAUGS TBD JCDL TBD Joint Vision 2020 TBD Km Kilometer lbs. pounds MAE Mechanical and...compatible with emerging JCDL and/or JAUGS . 2.3.2.2. Payload must be “plug and play.” 2.3.3. Communications 2.3.3.1. System communications shall be robust...Power JCDL JAUGS Joint Architecture for Unmanned Ground Systems JP-8 Jet Propulsion Fuel 8 km Kilometer lbs. Pounds LOS Line Of Sight MAE Mechanical

CRUSER News. Issue 30, Aug 2013

DTIC Science & Technology

2013-08-01

Versatile Low Cost Tactical SUAS by Dr. Richard Guiler, Physical Sciences Inc. • Small Unmanned Aircraft System ( SUAS )/Unattended Ground Sensor...NPS faculty JIFX 13-4 was held last week and included several different planned experiments in the unmanned systems /robot- ics thread. One of the many... planned experiments for the unmanned systems / robotics thread. • Tactical Operations for Multiple Swarm UAVs by Dr Timothy Chung, NPS • ងlb

Guidelines of the Design of Electropyrotechnic Firing Circuit for Unmanned Flight and Ground Test Projects

NASA Technical Reports Server (NTRS)

Gonzalez, Guillermo A.; Lucy, Melvin H.; Massie, Jeffrey J.

2013-01-01

The NASA Langley Research Center, Engineering Directorate, Electronic System Branch, is responsible for providing pyrotechnic support capabilities to Langley Research Center unmanned flight and ground test projects. These capabilities include device selection, procurement, testing, problem solving, firing system design, fabrication and testing; ground support equipment design, fabrication and testing; checkout procedures and procedure?s training to pyro technicians. This technical memorandum will serve as a guideline for the design, fabrication and testing of electropyrotechnic firing systems. The guidelines will discuss the entire process beginning with requirements definition and ending with development and execution.

Tip-over Prevention Through Heuristic Reactive Behaviors for Unmanned Ground Vehicles

DTIC Science & Technology

2014-05-01

Systems Center Pacific Unmanned Systems Group 53406 Woodward Road San Diego, CA 92152 ABSTRACT Skid-steer teleoperated robots are commonly used by...Reactive Behaviors Further author information: (Send correspondence to K.T.) K.T.: E-mail: kurt.talke@navy.mil, SPIE Proc. 9084: Unmanned Systems ...5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Space and Naval Warfare Systems Center

University of Pennsylvania MAGIC 2010 Final Report

DTIC Science & Technology

2011-01-10

and mapping ( SLAM ) techniques are employed to build a local map of the environment surrounding the robot. Readings from the two complementary LIDAR sen...IMU, LIDAR , Cameras Localization Disrupter UGV Local Navigation Sensors: GPS, IMU, LIDAR , Cameras Laser Control Localization Task Planner Strategy/Plan...various components shown in Figure 2. This is comprised of the following subsystems: • Sensor UGV: Mobile UGVs with LIDAR and camera sensors, GPS, and

Integration of unmanned systems for tactical operations within hostile environments

NASA Astrophysics Data System (ADS)

Maddux, Gary A.; Bosco, Charles D.; Lawrence, James D.

2006-05-01

The University of Alabama in Huntsville (UAH) is currently investigating techniques and technologies for the integration of a small unmanned aerial vehicle (SUAV) with small unmanned ground vehicles (SUGV). Each vehicle has its own set of unique capabilities, but the efficient integration of the two for a specific application requires modifying and integrating both systems. UAH has been flying and testing an autonomously-controlled small helicopter, called the Flying Bassett (Base Airborne Surveillance and Sensing for Emergency Threat Tracking) for over a year. Recently, integrated operations were performed with four SUGVs, the Matilda (Mesa Robotics, Huntsville, AL), the US Navy Vanguard, the UAH Rover, and the Penetrator (Mesa Robotics). The program has progressed from 1) building an air and ground capability for video and infrared surveillance, 2) integration with ground vehicles in realistic scenarios, to 3) deployment and recovery of ground vehicles. The work was done with the cooperation of the US Army at Ft. Benning, GA and Redstone Arsenal, AL, the Federal Bureau of Investigation in Huntsville, AL, the US Naval Reserve in Knoxville, TN, and local emergency organizations. The results so far have shown that when the air and ground systems are employed together, their utility is greatly enhanced.

Infrared Stereo Calibration for Unmanned Ground Vehicle Navigation

DTIC Science & Technology

2014-05-01

Josh Harguess: E -mail: joshua.harguess@navy.mil, Telephone: 1 619 553 0777 SPIE Proc. 9084: Unmanned Systems Technology XVI, Baltimore, MD, May 6-8...G., Diniz , H., Silvino, S., and de Andrade, R., “Thermal/visible au- tonomous stereo visio system calibration methodology for non-controlled

Online Aerial Terrain Mapping for Ground Robot Navigation.

PubMed

Peterson, John; Chaudhry, Haseeb; Abdelatty, Karim; Bird, John; Kochersberger, Kevin

2018-02-20

This work presents a collaborative unmanned aerial and ground vehicle system which utilizes the aerial vehicle's overhead view to inform the ground vehicle's path planning in real time. The aerial vehicle acquires imagery which is assembled into a orthomosaic and then classified. These terrain classes are used to estimate relative navigation costs for the ground vehicle so energy-efficient paths may be generated and then executed. The two vehicles are registered in a common coordinate frame using a real-time kinematic global positioning system (RTK GPS) and all image processing is performed onboard the unmanned aerial vehicle, which minimizes the data exchanged between the vehicles. This paper describes the architecture of the system and quantifies the registration errors between the vehicles.

Online Aerial Terrain Mapping for Ground Robot Navigation

PubMed Central

Peterson, John; Chaudhry, Haseeb; Abdelatty, Karim; Bird, John; Kochersberger, Kevin

2018-01-01

This work presents a collaborative unmanned aerial and ground vehicle system which utilizes the aerial vehicle’s overhead view to inform the ground vehicle’s path planning in real time. The aerial vehicle acquires imagery which is assembled into a orthomosaic and then classified. These terrain classes are used to estimate relative navigation costs for the ground vehicle so energy-efficient paths may be generated and then executed. The two vehicles are registered in a common coordinate frame using a real-time kinematic global positioning system (RTK GPS) and all image processing is performed onboard the unmanned aerial vehicle, which minimizes the data exchanged between the vehicles. This paper describes the architecture of the system and quantifies the registration errors between the vehicles. PMID:29461496

Networked sensors for the combat forces

NASA Astrophysics Data System (ADS)

Klager, Gene

2004-11-01

Real-time and detailed information is critical to the success of ground combat forces. Current manned reconnaissance, surveillance, and target acquisition (RSTA) capabilities are not sufficient to cover battlefield intelligence gaps, provide Beyond-Line-of-Sight (BLOS) targeting, and the ambush avoidance information necessary for combat forces operating in hostile situations, complex terrain, and conducting military operations in urban terrain. This paper describes a current US Army program developing advanced networked unmanned/unattended sensor systems to survey these gaps and provide the Commander with real-time, pertinent information. Networked Sensors for the Combat Forces plans to develop and demonstrate a new generation of low cost distributed unmanned sensor systems organic to the RSTA Element. Networked unmanned sensors will provide remote monitoring of gaps, will increase a unit"s area of coverage, and will provide the commander organic assets to complete his Battlefield Situational Awareness (BSA) picture for direct and indirect fire weapons, early warning, and threat avoidance. Current efforts include developing sensor packages for unmanned ground vehicles, small unmanned aerial vehicles, and unattended ground sensors using advanced sensor technologies. These sensors will be integrated with robust networked communications and Battle Command tools for mission planning, intelligence "reachback", and sensor data management. The network architecture design is based on a model that identifies a three-part modular design: 1) standardized sensor message protocols, 2) Sensor Data Management, and 3) Service Oriented Architecture. This simple model provides maximum flexibility for data exchange, information management and distribution. Products include: Sensor suites optimized for unmanned platforms, stationary and mobile versions of the Sensor Data Management Center, Battle Command planning tools, networked communications, and sensor management software. Details of these products and recent test results will be presented.

Cooperative Surveillance and Pursuit Using Unmanned Aerial Vehicles and Unattended Ground Sensors

PubMed Central

Las Fargeas, Jonathan; Kabamba, Pierre; Girard, Anouck

2015-01-01

This paper considers the problem of path planning for a team of unmanned aerial vehicles performing surveillance near a friendly base. The unmanned aerial vehicles do not possess sensors with automated target recognition capability and, thus, rely on communicating with unattended ground sensors placed on roads to detect and image potential intruders. The problem is motivated by persistent intelligence, surveillance, reconnaissance and base defense missions. The problem is formulated and shown to be intractable. A heuristic algorithm to coordinate the unmanned aerial vehicles during surveillance and pursuit is presented. Revisit deadlines are used to schedule the vehicles' paths nominally. The algorithm uses detections from the sensors to predict intruders' locations and selects the vehicles' paths by minimizing a linear combination of missed deadlines and the probability of not intercepting intruders. An analysis of the algorithm's completeness and complexity is then provided. The effectiveness of the heuristic is illustrated through simulations in a variety of scenarios. PMID:25591168

Skid steer fuel cell powered unmanned ground vehicle (Burro)

NASA Astrophysics Data System (ADS)

Meldrum, Jay S.; Green, Christopher A.

2008-04-01

The use of alternative energy technology for vehicle propulsion and auxiliary power is becoming more important. Work is being performed at Michigan Technological University's Keweenaw Research Center on an Army Research Laboratory cooperative agreement to develop two unmanned ground vehicles for military applications. A wide range of alternative energy technologies were investigated. Hydrogen-powered proton exchange membrane fuel cells were identified as the most appropriate alternative energy source. This is due to some development and commercialization which makes the technology "drop-in plug-in" for immediate use. We have previously presented research work on a small unmanned ground vehicle demonstration platform where the fuel cell is the only power source. We now present research work on the integration of a fuel cell onto a larger skid steer platform. The dual-power capability of this vehicle can provide a modest level of propulsion in "engine-off mode" and may also be used to power directed energy devices which have applications in countermine and similar threat technologies.

Automatic Forest-Fire Measuring Using Ground Stations and Unmanned Aerial Systems

PubMed Central

Martínez-de Dios, José Ramiro; Merino, Luis; Caballero, Fernando; Ollero, Anibal

2011-01-01

This paper presents a novel system for automatic forest-fire measurement using cameras distributed at ground stations and mounted on Unmanned Aerial Systems (UAS). It can obtain geometrical measurements of forest fires in real-time such as the location and shape of the fire front, flame height and rate of spread, among others. Measurement of forest fires is a challenging problem that is affected by numerous potential sources of error. The proposed system addresses them by exploiting the complementarities between infrared and visual cameras located at different ground locations together with others onboard Unmanned Aerial Systems (UAS). The system applies image processing and geo-location techniques to obtain forest-fire measurements individually from each camera and then integrates the results from all the cameras using statistical data fusion techniques. The proposed system has been extensively tested and validated in close-to-operational conditions in field fire experiments with controlled safety conditions carried out in Portugal and Spain from 2001 to 2006. PMID:22163958

Team VaCAS Design and Development of Cooperative UGV System

DTIC Science & Technology

2011-02-04

Mapping ( SLAM ) [24]. Similar to such work, the technique to be used in the project will also (1) use the last reliably available data as the reference...Losada1, D., Matia1, F., Pedraza1, L., Jimenez A. and Galan, R., Consistency of SLAM -EKF Algorithms for Indoor Environments, Journal of Intelligent and...mounted on the UGV 1 include GPS for outdoor navigation, LiDAR for obstacle avoidance and mapping and camera for OOI detection and localization. UGVs 2

Fuel-cell powered unmanned ground vehicle

NASA Astrophysics Data System (ADS)

Meldrum, Jay S.; Green, Christopher A.; Gwaltney, Geoffrey D.; Bradley, Scott A.; Keith, Jason M.; Podlesak, Thomas F.

2007-04-01

The use of alternative energy technology for vehicle propulsion and auxiliary power is becoming more important. Work is being performed at Michigan Technological University's Keweenaw Research Center on an Army Research Laboratory cooperative agreement to develop two unmanned ground vehicles for military applications. A wide range of alternative energy technologies were investigated, and hydrogen-powered proton exchange membrane fuel cells were identified as the most appropriate alternative energy source. This is due to some development and commercialization which makes the technology "drop-in plug-in" for immediate use. We present research work on a small unmanned ground vehicle demonstration platform where the fuel cell is the only power source. We also present research work on the integration of a fuel cell onto a large existing platform. The dual-power capability of this vehicle can provide a modest level of propulsion in "engine-off mode" and may also be used to power directed energy devices which have applications in countermine and similar threat technologies.

Automatic forest-fire measuring using ground stations and Unmanned Aerial Systems.

PubMed

Martínez-de Dios, José Ramiro; Merino, Luis; Caballero, Fernando; Ollero, Anibal

2011-01-01

This paper presents a novel system for automatic forest-fire measurement using cameras distributed at ground stations and mounted on Unmanned Aerial Systems (UAS). It can obtain geometrical measurements of forest fires in real-time such as the location and shape of the fire front, flame height and rate of spread, among others. Measurement of forest fires is a challenging problem that is affected by numerous potential sources of error. The proposed system addresses them by exploiting the complementarities between infrared and visual cameras located at different ground locations together with others onboard Unmanned Aerial Systems (UAS). The system applies image processing and geo-location techniques to obtain forest-fire measurements individually from each camera and then integrates the results from all the cameras using statistical data fusion techniques. The proposed system has been extensively tested and validated in close-to-operational conditions in field fire experiments with controlled safety conditions carried out in Portugal and Spain from 2001 to 2006.

Unmanned Ground Systems Roadmap

DTIC Science & Technology

2011-07-01

6 1.3.1 RDECOM, Academia, Industry ..................................................................................... 6 1.3.2 Rapid...for unmanned capabilities can be supported and from which PORs can be facilitated when necessary  The RS JPO formed a Government/ Industry Working...products. 1.3.1 RDECOM, Academia, Industry Given the RS JPO‟s close working relations with academia, industry partners and the RDECOM Labs, the

Land, sea, and air unmanned systems research and development at SPAWAR Systems Center Pacific

NASA Astrophysics Data System (ADS)

Nguyen, Hoa G.; Laird, Robin; Kogut, Greg; Andrews, John; Fletcher, Barbara; Webber, Todd; Arrieta, Rich; Everett, H. R.

2009-05-01

The Space and Naval Warfare (SPAWAR) Systems Center Pacific (SSC Pacific) has a long and extensive history in unmanned systems research and development, starting with undersea applications in the 1960s and expanding into ground and air systems in the 1980s. In the ground domain, we are addressing force-protection scenarios using large unmanned ground vehicles (UGVs) and fixed sensors, and simultaneously pursuing tactical and explosive ordnance disposal (EOD) operations with small man-portable robots. Technology thrusts include improving robotic intelligence and functionality, autonomous navigation and world modeling in urban environments, extended operational range of small teleoperated UGVs, enhanced human-robot interaction, and incorporation of remotely operated weapon systems. On the sea surface, we are pushing the envelope on dynamic obstacle avoidance while conforming to established nautical rules-of-the-road. In the air, we are addressing cooperative behaviors between UGVs and small vertical-takeoff- and-landing unmanned air vehicles (UAVs). Underwater applications involve very shallow water mine countermeasures, ship hull inspection, oceanographic data collection, and deep ocean access. Specific technology thrusts include fiber-optic communications, adaptive mission controllers, advanced navigation techniques, and concepts of operations (CONOPs) development. This paper provides a review of recent accomplishments and current status of a number of projects in these areas.

Modeling and simulation of an unmanned ground vehicle power system

NASA Astrophysics Data System (ADS)

Broderick, John; Hartner, Jack; Tilbury, Dawn M.; Atkins, Ella M.

2014-06-01

Long-duration missions challenge ground robot systems with respect to energy storage and efficient conversion to power on demand. Ground robot systems can contain multiple power sources such as fuel cell, battery and/or ultra-capacitor. This paper presents a hybrid systems framework for collectively modeling the dynamics and switching between these different power components. The hybrid system allows modeling power source on/off switching and different regimes of operation, together with continuous parameters such as state of charge, temperature, and power output. We apply this modeling framework to a fuel cell/battery power system applicable to unmanned ground vehicles such as Packbot or TALON. A simulation comparison of different control strategies is presented. These strategies are compared based on maximizing energy efficiency and meeting thermal constraints.

The 13 th Annual Intelligent Ground Vehicle Competition: intelligent ground vehicles created by intelligent teams

NASA Astrophysics Data System (ADS)

Theisen, Bernard L.

2005-10-01

The Intelligent Ground Vehicle Competition (IGVC) is one of three, unmanned systems, student competitions that were founded by the Association for Unmanned Vehicle Systems International (AUVSI) in the 1990s. The IGVC is a multidisciplinary exercise in product realization that challenges college engineering student teams to integrate advanced control theory, machine vision, vehicular electronics, and mobile platform fundamentals to design and build an unmanned system. Teams from around the world focus on developing a suite of dual-use technologies to equip ground vehicles of the future with intelligent driving capabilities. Over the past 13 years, the competition has challenged undergraduate, graduate and Ph.D. students with real world applications in intelligent transportation systems, the military and manufacturing automation. To date, teams from over 50 universities and colleges have participated. This paper describes some of the applications of the technologies required by this competition and discusses the educational benefits. The primary goal of the IGVC is to advance engineering education in intelligent vehicles and related technologies. The employment and professional networking opportunities created for students and industrial sponsors through a series of technical events over the three-day competition are highlighted. Finally, an assessment of the competition based on participant feedback is presented.

Guidance and Navigation Requirements for Unmanned Flyby and Swingby Missions to the Outer Planets. Volume 3; Low Thrust Missions, Phase B

NASA Technical Reports Server (NTRS)

1970-01-01

The guidance and navigation requirements for unmanned missions to the outer planets, assuming constant, low thrust, ion propulsion are discussed. The navigational capability of the ground based Deep Space Network is compared to the improvements in navigational capability brought about by the addition of guidance and navigation related onboard sensors. Relevant onboard sensors include: (1) the optical onboard navigation sensor, (2) the attitude reference sensors, and (3) highly sensitive accelerometers. The totally ground based, and the combination ground based and onboard sensor systems are compared by means of the estimated errors in target planet ephemeris, and the spacecraft position with respect to the planet.

Remote imagery for unmanned ground vehicles: the future of path planning for ground robotics

NASA Astrophysics Data System (ADS)

Frederick, Philip A.; Theisen, Bernard L.; Ward, Derek

2006-10-01

Remote Imagery for Unmanned Ground Vehicles (RIUGV) uses a combination of high-resolution multi-spectral satellite imagery and advanced commercial off-the-self (COTS) object-oriented image processing software to provide automated terrain feature extraction and classification. This information, along with elevation data, infrared imagery, a vehicle mobility model and various meta-data (local weather reports, Zobler Soil map, etc...), is fed into automated path planning software to provide a stand-alone ability to generate rapidly updateable dynamic mobility maps for Manned or Unmanned Ground Vehicles (MGVs or UGVs). These polygon based mobility maps can reside on an individual platform or a tactical network. When new information is available, change files are generated and ingested into existing mobility maps based on user selected criteria. Bandwidth concerns are mitigated by the use of shape files for the representation of the data (e.g. each object in the scene is represented by a shape file and thus can be transmitted individually). User input (desired level of stealth, required time of arrival, etc...) determines the priority in which objects are tagged for updates. This paper will also discuss the planned July 2006 field experiment.

High clearance phenotyping systems for season-long measurement of corn, sorghum and other row crops to complement unmanned aerial vehicle systems

NASA Astrophysics Data System (ADS)

Murray, Seth C.; Knox, Leighton; Hartley, Brandon; Méndez-Dorado, Mario A.; Richardson, Grant; Thomasson, J. Alex; Shi, Yeyin; Rajan, Nithya; Neely, Haly; Bagavathiannan, Muthukumar; Dong, Xuejun; Rooney, William L.

2016-05-01

The next generation of plant breeding progress requires accurately estimating plant growth and development parameters to be made over routine intervals within large field experiments. Hand measurements are laborious and time consuming and the most promising tools under development are sensors carried by ground vehicles or unmanned aerial vehicles, with each specific vehicle having unique limitations. Previously available ground vehicles have primarily been restricted to monitoring shorter crops or early growth in corn and sorghum, since plants taller than a meter could be damaged by a tractor or spray rig passing over them. Here we have designed two and already constructed one of these self-propelled ground vehicles with adjustable heights that can clear mature corn and sorghum without damage (over three meters of clearance), which will work for shorter row crops as well. In addition to regular RGB image capture, sensor suites are incorporated to estimate plant height, vegetation indices, canopy temperature and photosynthetically active solar radiation, all referenced using RTK GPS to individual plots. These ground vehicles will be useful to validate data collected from unmanned aerial vehicles and support hand measurements taken on plots.

Unmanned aerial vehicle: A unique platform for low-altitude remote sensing for crop management

USDA-ARS?s Scientific Manuscript database

Unmanned aerial vehicles (UAV) provide a unique platform for remote sensing to monitor crop fields that complements remote sensing from satellite, aircraft and ground-based platforms. The UAV-based remote sensing is versatile at ultra-low altitude to be able to provide an ultra-high-resolution imag...

Two-dimensional laser servoing for precision motion control of an ODV robotic license plate recognition system

NASA Astrophysics Data System (ADS)

Song, Zhen; Moore, Kevin L.; Chen, YangQuan; Bahl, Vikas

2003-09-01

As an outgrowth of series of projects focused on mobility of unmanned ground vehicles (UGV), an omni-directional (ODV), multi-robot, autonomous mobile parking security system has been developed. The system has two types of robots: the low-profile Omni-Directional Inspection System (ODIS), which can be used for under-vehicle inspections, and the mid-sized T4 robot, which serves as a ``marsupial mothership'' for the ODIS vehicles and performs coarse resolution inspection. A key task for the T4 robot is license plate recognition (LPR). For a successful LPR task without compromising the recognition rate, the robot must be able to identify the bumper locations of vehicles in the parking area and then precisely position the LPR camera relative to the bumper. This paper describes a 2D-laser scanner based approach to bumper identification and laser servoing for the T4 robot. The system uses a gimbal-mounted scanning laser. As the T4 robot travels down a row of parking stalls, data is collected from the laser every 100ms. For each parking stall in the range of the laser during the scan, the data is matched to a ``bumper box'' corresponding to where a car bumper is expected, resulting in a point cloud of data corresponding to a vehicle bumper for each stall. Next, recursive line-fitting algorithms are used to determine a line for the data in each stall's ``bumper box.'' The fitting technique uses Hough based transforms, which are robust against segmentation problems and fast enough for real-time line fitting. Once a bumper line is fitted with an acceptable confidence, the bumper location is passed to the T4 motion controller, which moves to position the LPR camera properly relative to the bumper. The paper includes examples and results that show the effectiveness of the technique, including its ability to work in real-time.

Enabling unmanned capabilities in the tactical wheeled vehicle fleet of the future

NASA Astrophysics Data System (ADS)

Zych, Noah

2012-06-01

From transporting troops and weapons systems to supplying beans, bullets, and Band-Aids to front-line warfighters, tactical wheeled vehicles serve as the materiel backbone anywhere there are boots on the ground. Drawing from the U.S. Army's Tactical Wheeled Vehicle Strategy and the Marine Corps Vision & Strategy 2025 reports, one may conclude that the services have modest expectations for the introduction of large unmanned ground systems into operational roles in the next 15 years. However, the Department of Defense has already invested considerably in the research and development of full-size UGVs-and commanders deployed in both Iraq and Afghanistan have advocated the urgent fielding of early incarnations of this technology, believing it could make a difference on their battlefields today. For military UGVs to evolve from mere tactical advantages into strategic assets with developed doctrine, they must become as trustworthy as a well-trained warfighter in performing their assigned task. Starting with the Marine Corps' ongoing Cargo Unmanned Ground Vehicle program as a baseline, and informed by feedback from previously deployed subject matter experts, this paper examines the gaps which presently exist in UGVs from a mission-capable perspective. It then considers viable near-term technical solutions to meet today's functional requirements, as well as long-term development strategies to enable truly robust performance. With future conflicts expected to be characterized by increasingly complex operational environments and a broad spectrum of rapidly adapting threats, one of the largest challenges for unmanned ground systems will be the ability to exhibit agility in unpredictable circumstances.

Advanced Fiber Optic-Based Sensing Technology for Unmanned Aircraft Systems

NASA Technical Reports Server (NTRS)

Richards, Lance; Parker, Allen R.; Piazza, Anthony; Ko, William L.; Chan, Patrick; Bakalyar, John

2011-01-01

This presentation provides an overview of fiber optic sensing technology development activities performed at NASA Dryden in support of Unmanned Aircraft Systems. Examples of current and previous work are presented in the following categories: algorithm development, system development, instrumentation installation, ground R&D, and flight testing. Examples of current research and development activities are provided.

Real-time Accurate Surface Reconstruction Pipeline for Vision Guided Planetary Exploration Using Unmanned Ground and Aerial Vehicles

NASA Technical Reports Server (NTRS)

Almeida, Eduardo DeBrito

2012-01-01

This report discusses work completed over the summer at the Jet Propulsion Laboratory (JPL), California Institute of Technology. A system is presented to guide ground or aerial unmanned robots using computer vision. The system performs accurate camera calibration, camera pose refinement and surface extraction from images collected by a camera mounted on the vehicle. The application motivating the research is planetary exploration and the vehicles are typically rovers or unmanned aerial vehicles. The information extracted from imagery is used primarily for navigation, as robot location is the same as the camera location and the surfaces represent the terrain that rovers traverse. The processed information must be very accurate and acquired very fast in order to be useful in practice. The main challenge being addressed by this project is to achieve high estimation accuracy and high computation speed simultaneously, a difficult task due to many technical reasons.

Applications suitable for unmanned and autonomous missions utilizing the Tactical Amphibious Ground Support (TAGS) platform

NASA Astrophysics Data System (ADS)

Lewis, Paul J.; Torrie, Mitchel R.; Omilon, Paul M.

2004-09-01

The value of unmanned vehicles is directly related to the applications to which it can be successfully applied. Many applications exist and have been identified as suitable for unmanned vehicles, especially those involving dull, dirty, difficult, and dangerous tasks. This paper will highlight applications, missions, and capabilities that have been demonstrated on the TAGS platform to date as well as future application and mission considerations. When evaluating real world applications for this type of vehicle, one must take into account and balance the complexity inherent to the control and safeguarding requirements of a large autonomous ground vehicle with the simplicity required for commercial or military field use. In addition, suitability for a particular application may be limited by the size, weight, fuel consumption, reliability, terrain crossing capability, and other abilities of a vehicle and the intelligent software system and sensors commanding it.

Collaborative engagement experiment (CEE)

NASA Astrophysics Data System (ADS)

Wade, Robert L.; Reames, Joseph M.

2005-05-01

Unmanned ground and air systems operating in collaboration have the potential to provide future Joint Forces a significant capability for operations in complex terrain. Ground and air collaborative engagements potentially offer force conservation, perform timely acquisition and dissemination of essential combat information, and can eliminate high value and time critical targets. These engagements can also add considerably to force survivability by reducing soldier and equipment exposure during critical operations. The Office of the Secretary of Defense, Joint Robotics Program (JRP) sponsored Collaborative Engagement Experiment (CEE) is a consolidation of separate Air Force, Army and Navy collaborative efforts to provide a Joint capability. The Air Force Research Laboratory (AFRL), Material and Manufacturing Directorate, Aerospace Expeditionary Force Division, Force Protection Branch (AFRLMLQF), The Army Aviation and Missile Research, Development and Engineering Center (AMRDEC) Joint Technology Center (JTC)/Systems Integration Laboratory (SIL), and the Space and Naval Warfare Systems Center-San Diego (SSC San Diego) are conducting technical research and proof of principle for an envisioned operational concept for extended range, three dimensional, collaborative operations between unmanned systems, with enhanced situational awareness for lethal operations in complex terrain. This program will assess information requirements and conduct experiments to identify and resolve technical risks for collaborative engagements using Unmanned Ground Vehicles (UGVs) and Unmanned Aerial Vehicles (UAVs). It will research, develop and physically integrate multiple unmanned systems and conduct live collaborative experiments. Modeling and Simulation systems will be upgraded to reflect engineering fidelity levels to greater understand technical challenges to operate as a team. This paper will provide an update of a multi-year program and will concentrate primarily on the JTC/SIL efforts. Other papers will outline in detail the Air Force and Navy portions of this effort.

Design and development of a robust ATP subsystem for the Altair UAV-to-Ground lasercomm 2.5 Gbps demonstration

NASA Technical Reports Server (NTRS)

Ortiz, G. G.; Lee, S.; Monacos, S.; Wright, M.; Biswas, A.

2003-01-01

A robust acquisition, tracking and pointing (ATP) subsystem is being developed for the 2.5 Gigabit per second (Gbps) Unmanned-Aerial-Vehicle (UAV) to ground free-space optical communications link project.

Multispectral and DSLR sensors for assessing crop stress in corn and cotton using fixed-wing unmanned air systems

NASA Astrophysics Data System (ADS)

Valasek, John; Henrickson, James V.; Bowden, Ezekiel; Shi, Yeyin; Morgan, Cristine L. S.; Neely, Haly L.

2016-05-01

As small unmanned aircraft systems become increasingly affordable, reliable, and formally recognized under federal regulation, they become increasingly attractive as novel platforms for civil applications. This paper details the development and demonstration of fixed-wing unmanned aircraft systems for precision agriculture tasks. Tasks such as soil moisture content and high throughput phenotyping are considered. Rationale for sensor, vehicle, and ground equipment selections are provided, in addition to developed flight operation procedures for minimal numbers of crew. Preliminary imagery results are presented and analyzed, and these results demonstrate that fixed-wing unmanned aircraft systems modified to carry non-traditional sensors at extended endurance durations can provide high quality data that is usable for serious scientific analysis.

Remote operation of the Black Knight unmanned ground combat vehicle

NASA Astrophysics Data System (ADS)

Valois, Jean-Sebastien; Herman, Herman; Bares, John; Rice, David P.

2008-04-01

The Black Knight is a 12-ton, C-130 deployable Unmanned Ground Combat Vehicle (UGCV). It was developed to demonstrate how unmanned vehicles can be integrated into a mechanized military force to increase combat capability while protecting Soldiers in a full spectrum of battlefield scenarios. The Black Knight is used in military operational tests that allow Soldiers to develop the necessary techniques, tactics, and procedures to operate a large unmanned vehicle within a mechanized military force. It can be safely controlled by Soldiers from inside a manned fighting vehicle, such as the Bradley Fighting Vehicle. Black Knight control modes include path tracking, guarded teleoperation, and fully autonomous movement. Its state-of-the-art Autonomous Navigation Module (ANM) includes terrain-mapping sensors for route planning, terrain classification, and obstacle avoidance. In guarded teleoperation mode, the ANM data, together with automotive dials and gages, are used to generate video overlays that assist the operator for both day and night driving performance. Remote operation of various sensors also allows Soldiers to perform effective target location and tracking. This document covers Black Knight's system architecture and includes implementation overviews of the various operation modes. We conclude with lessons learned and development goals for the Black Knight UGCV.

The 20th annual intelligent ground vehicle competition: building a generation of robotists

NASA Astrophysics Data System (ADS)

Theisen, Bernard L.; Kosinski, Andrew

2013-01-01

The Intelligent Ground Vehicle Competition (IGVC) is one of four, unmanned systems, student competitions that were founded by the Association for Unmanned Vehicle Systems International (AUVSI). The IGVC is a multidisciplinary exercise in product realization that challenges college engineering student teams to integrate advanced control theory, machine vision, vehicular electronics and mobile platform fundamentals to design and build an unmanned system. Teams from around the world focus on developing a suite of dual-use technologies to equip ground vehicles of the future with intelligent driving capabilities. Over the past 20 years, the competition has challenged undergraduate, graduate and Ph.D. students with real world applications in intelligent transportation systems, the military and manufacturing automation. To date, teams from over 80 universities and colleges have participated. This paper describes some of the applications of the technologies required by this competition and discusses the educational benefits. The primary goal of the IGVC is to advance engineering education in intelligent vehicles and related technologies. The employment and professional networking opportunities created for students and industrial sponsors through a series of technical events over the four-day competition are highlighted. Finally, an assessment of the competition based on participation is presented.

The twelfth annual Intelligent Ground Vehicle Competition: team approaches to intelligent vehicles

NASA Astrophysics Data System (ADS)

Theisen, Bernard L.; Maslach, Daniel

2004-10-01

The Intelligent Ground Vehicle Competition (IGVC) is one of three, unmanned systems, student competitions that were founded by the Association for Unmanned Vehicle Systems International (AUVSI) in the 1990s. The IGVC is a multidisciplinary exercise in product realization that challenges college engineering student teams to integrate advanced control theory, machine vision, vehicular electronics, and mobile platform fundamentals to design and build an unmanned system. Both U.S. and international teams focus on developing a suite of dual-use technologies to equip ground vehicles of the future with intelligent driving capabilities. Over the past 12 years, the competition has challenged undergraduate, graduate and Ph.D. students with real world applications in intelligent transportation systems, the military and manufacturing automation. To date, teams from over 43 universities and colleges have participated. This paper describes some of the applications of the technologies required by this competition and discusses the educational benefits. The primary goal of the IGVC is to advance engineering education in intelligent vehicles and related technologies. The employment and professional networking opportunities created for students and industrial sponsors through a series of technical events over the three-day competition are highlighted. Finally, an assessment of the competition based on participant feedback is presented.

The 21st annual intelligent ground vehicle competition: robotists for the future

NASA Astrophysics Data System (ADS)

Theisen, Bernard L.

2013-12-01

The Intelligent Ground Vehicle Competition (IGVC) is one of four, unmanned systems, student competitions that were founded by the Association for Unmanned Vehicle Systems International (AUVSI). The IGVC is a multidisciplinary exercise in product realization that challenges college engineering student teams to integrate advanced control theory, machine vision, vehicular electronics and mobile platform fundamentals to design and build an unmanned system. Teams from around the world focus on developing a suite of dual-use technologies to equip ground vehicles of the future with intelligent driving capabilities. Over the past 21 years, the competition has challenged undergraduate, graduate and Ph.D. students with real world applications in intelligent transportation systems, the military and manufacturing automation. To date, teams from over 80 universities and colleges have participated. This paper describes some of the applications of the technologies required by this competition and discusses the educational benefits. The primary goal of the IGVC is to advance engineering education in intelligent vehicles and related technologies. The employment and professional networking opportunities created for students and industrial sponsors through a series of technical events over the fourday competition are highlighted. Finally, an assessment of the competition based on participation is presented.

Distributed Pheromone-Based Swarming Control of Unmanned Air and Ground Vehicles for RSTA

DTIC Science & Technology

2008-03-20

Forthcoming in Proceedings of SPIE Defense & Security Conference, March 2008, Orlando, FL Distributed Pheromone -Based Swarming Control of Unmanned...describes recent advances in a fully distributed digital pheromone algorithm that has demonstrated its effectiveness in managing the complexity of...onboard digital pheromone responding to the needs of the automatic target recognition algorithms. UAVs and UGVs controlled by the same pheromone algorithm

Vector Pursuit Path Tracking for Autonomous Ground Vehicles

DTIC Science & Technology

2000-08-01

vi INTRODUCTION ...........................................................................................................1...other geometric path-tracking techniques. 1 CHAPTER 1 INTRODUCTION An autonomous vehicle is one that is capable of automatic navigation. It is...Joint Architecture for Unmanned Ground Vehicles ( JAUGS ) working group meeting held at the University of Florida. 5 Figure 1.5: Autonomous

Distributed pheromone-based swarming control of unmanned air and ground vehicles for RSTA

NASA Astrophysics Data System (ADS)

Sauter, John A.; Mathews, Robert S.; Yinger, Andrew; Robinson, Joshua S.; Moody, John; Riddle, Stephanie

2008-04-01

The use of unmanned vehicles in Reconnaissance, Surveillance, and Target Acquisition (RSTA) applications has received considerable attention recently. Cooperating land and air vehicles can support multiple sensor modalities providing pervasive and ubiquitous broad area sensor coverage. However coordination of multiple air and land vehicles serving different mission objectives in a dynamic and complex environment is a challenging problem. Swarm intelligence algorithms, inspired by the mechanisms used in natural systems to coordinate the activities of many entities provide a promising alternative to traditional command and control approaches. This paper describes recent advances in a fully distributed digital pheromone algorithm that has demonstrated its effectiveness in managing the complexity of swarming unmanned systems. The results of a recent demonstration at NASA's Wallops Island of multiple Aerosonde Unmanned Air Vehicles (UAVs) and Pioneer Unmanned Ground Vehicles (UGVs) cooperating in a coordinated RSTA application are discussed. The vehicles were autonomously controlled by the onboard digital pheromone responding to the needs of the automatic target recognition algorithms. UAVs and UGVs controlled by the same pheromone algorithm self-organized to perform total area surveillance, automatic target detection, sensor cueing, and automatic target recognition with no central processing or control and minimal operator input. Complete autonomy adds several safety and fault tolerance requirements which were integrated into the basic pheromone framework. The adaptive algorithms demonstrated the ability to handle some unplanned hardware failures during the demonstration without any human intervention. The paper describes lessons learned and the next steps for this promising technology.

Robotic vehicle mobility and task performance: A flexible control modality for manned systems

NASA Technical Reports Server (NTRS)

Eldredge, Frederick

1994-01-01

In the early 1980's, a number of concepts were developed for applying robotics to ground systems. The majority of these early application concepts envisioned robotics technology embedded in dedicated unmanned systems; i.e., unmanned systems with no provision for direct manned control of the platform. Although these concepts offered advantages peculiar to platforms designed from the outset exclusively for unmanned operation--i.e., no crew compartment--their findings would require costs and support for a new class of unmanned systems. The current era of reduced budgets and increasing focus on rapid force projection has created new opportunities to examine the value of an alternative concept: the use of existing manned platforms with an ability to quickly shift from normal manned operation to unmanned should a particularly harzardous situation arise. The author of this paper addresses the evolution of robotic vehicle concepts and technology testbeds from exclusively unmanned systems to a variety of 'optionally manned' systems which have been designed with minimum intrusion actuator and control equipment to minimize degradation of vehicle performance in manned modes of operation.

An arm wearable haptic interface for impact sensing on unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Choi, Yunshil; Hong, Seung-Chan; Lee, Jung-Ryul

2017-04-01

In this paper, an impact monitoring system using fiber Bragg grating (FBG) sensors and vibro-haptic actuators has been introduced. The system is suggested for structural health monitoring (SHM) for unmanned aerial vehicles (UAVs), by making a decision with human-robot interaction. The system is composed with two major subsystems; an on-board system equipped on UAV and an arm-wearable interface for ground pilot. The on-board system acquires impact-induced wavelength changes and performs localization process, which was developed based on arrival time calculation. The arm-wearable interface helps ground pilots to make decision about impact location themselves by stimulating their tactile-sense with motor vibration.

Control and Non-Payload Communications Links for Integrated Unmanned Aircraft Operations

NASA Technical Reports Server (NTRS)

Kerczewski, Robert J.; Griner, James H.

2012-01-01

Technology for unmanned aircraft has advanced so rapidly in recent years that many new applications to public and commercial use are being proposed and implemented. In many countries, emphasis is now being placed on developing the means to allow unmanned aircraft to operate within non-segregated airspace along with commercial, cargo and other piloted and passenger-carrying aircraft.In the U.S., Congress has mandated that the Federal Aviation Administration reduce and remove restrictions on unmanned aircraft operations in a relatively short time frame. To accomplish this, a number of technical and regulatory hurdles must be overcome. A key hurdle involve the communications link connecting the remote pilot located at a ground control station with the aircraft in the airspace, referred to as the Control and Non-Payload Communications (CNPC) link. This link represents a safety critical communications link, and thus requires dedicated and protected aviation spectrum as well as national and international standards defining the operational requirements the CNPC system. The CNPC link must provide line-of-site (LOS) communications, primarily through a ground-based communication system, and beyond-line-of-sight (BLOS) communication achieved using satellite communications. In the U.S., the National Aeronautics and Space Administration (NASA) is charged with providing the technical body of evidence to support spectrum allocation requirements and national and international standards development for the CNPC link. This paper provides a description of the CNPC system, an overview of NASA's CNPC project, and current results in technology assessment, air-ground propagation characterization, and supporting system studies and analyses will be presented.

Possibilities of Uas for Maritime Monitoring

NASA Astrophysics Data System (ADS)

Klimkowska, A.; Lee, I.; Choi, K.

2016-06-01

In the last few years, Unmanned Aircraft Systems (UAS) have become more important and its use for different application is appreciated. At the beginning UAS were used for military purposes. These successful applications initiated interest among researchers to find uses of UAS for civilian purposes, as they are alternative to both manned and satellite systems in acquiring high-resolution remote sensing data at lower cost while long flight duration. As UAS are built from many components such as unmanned aerial vehicle (UAV), sensing payloads, communication systems, ground control stations, recovery and launch equipment, and supporting equipment, knowledge about its functionality and characteristics is crucial for missions. Therefore, finding appropriate configuration of all elements to fulfill requirements of the mission is a very difficult, yet important task. UAS may be used in various maritime applications such as ship detection, red tide detection and monitoring, border patrol, tracking of pollution at sea and hurricane monitoring just to mention few. One of the greatest advantages of UAV is their ability to fly over dangerous and hazardous areas, where sending manned aircraft could be risky for a crew. In this article brief description of aerial unmanned system components is introduced. Firstly characteristics of unmanned aerial vehicles are presented, it continues with introducing inertial navigation system, communication systems, sensing payloads, ground control stations, and ground and recovery equipment. Next part introduces some examples of UAS for maritime applications. This is followed by suggestions of key indicators which should be taken into consideration while choosing UAS. Last part talks about configuration schemes of UAVs and sensor payloads suggested for some maritime applications.

Integration of robotic resources into FORCEnet

NASA Astrophysics Data System (ADS)

Nguyen, Chinh; Carroll, Daniel; Nguyen, Hoa

2006-05-01

The Networked Intelligence, Surveillance, and Reconnaissance (NISR) project integrates robotic resources into Composeable FORCEnet to control and exploit unmanned systems over extremely long distances. The foundations are built upon FORCEnet-the U.S. Navy's process to define C4ISR for net-centric operations-and the Navy Unmanned Systems Common Control Roadmap to develop technologies and standards for interoperability, data sharing, publish-and-subscribe methodology, and software reuse. The paper defines the goals and boundaries for NISR with focus on the system architecture, including the design tradeoffs necessary for unmanned systems in a net-centric model. Special attention is given to two specific scenarios demonstrating the integration of unmanned ground and water surface vehicles into the open-architecture web-based command-and-control information-management system of Composeable FORCEnet. Planned spiral development for NISR will improve collaborative control, expand robotic sensor capabilities, address multiple domains including underwater and aerial platforms, and extend distributive communications infrastructure for battlespace optimization for unmanned systems in net-centric operations.

Bioinspired optical sensors for unmanned aerial systems

NASA Astrophysics Data System (ADS)

Chahl, Javaan; Rosser, Kent; Mizutani, Akiko

2011-04-01

Insects are dependant on the spatial, spectral and temporal distributions of light in the environment for flight control and navigation. This paper reports on flight trials of implementations of insect inspired behaviors on unmanned aerial vehicles. Optical flow methods for maintaining a constant height above ground and a constant course have been demonstrated to provide navigation capabilities that are impossible using conventional avionics sensors. Precision control of height above ground and ground course were achieved over long distances. Other vision based techniques demonstrated include a biomimetic stabilization sensor that uses the ultraviolet and green bands of the spectrum, and a sky polarization compass. Both of these sensors were tested over long trajectories in different directions, in each case showing performance similar to low cost inertial heading and attitude systems. The behaviors demonstrate some of the core functionality found in the lower levels of the sensorimotor system of flying insects and shows promise for more integrated solutions in the future.

11th Annual Intelligent Ground Vehicle Competition: team approaches to intelligent driving and machine vision

NASA Astrophysics Data System (ADS)

Theisen, Bernard L.; Lane, Gerald R.

2003-10-01

The Intelligent Ground Vehicle Competition (IGVC) is one of three, unmanned systems, student competitions that were founded by the Association for Unmanned Vehicle Systems International (AUVSI) in the 1990's. The IGVC is a multidisciplinary exercise in product realization that challenges college engineering student teams to integrate advanced control theory, machine vision, vehicular electronics, and mobile platform fundamentals to design and build an unmanned system. Both the U.S. and international teams focus on developing a suite of dual-use technologies to equip ground vehicles of the future with intelligtent driving capabilities. Over the past 11 years, the competition has challenged both undergraduates and graduates, including Ph.D. students with real world applications in intelligent transportation systems, the military, and manufacturing automation. To date, teams from over 40 universities and colleges have participated. In this paper, we describe some of the applications of the technologies required by this competition, and discuss the educational benefits. The primary goal of the IGVC is to advance engineering education in intelligent vehicles and related technologies. The employment and professional networking opportunities created for students and industrial sponsors through a series of technical events over the three-day competition are highlighted. Finally, an assessment of the competition based on participant feedback is presented.

Swarming Unmanned Aerial Vehicles (UAVS): Extending Marine Aviation Ground Task Force Communications Using UAVS

DTIC Science & Technology

2015-03-02

balloons , large UAVs, and satellite communications are all employed to mitigate LOS and OTH communication on the battlefield. The Marine Corps’ fleets...Phang, N. S. (2006). Tethered operation of autonomous aerial vehicles to provide extended fields of view for autonomous ground vehicles (Master’s

Aerial radiation monitoring around the Fukushima Dai-ichi Nuclear Power Plant using an unmanned helicopter.

PubMed

Sanada, Yukihisa; Torii, Tatsuo

2015-01-01

The Great East Japan Earthquake on March 11, 2011 generated a series of large tsunami that seriously damaged the Fukushima Dai-ichi Nuclear Power Plant (FDNPP), which resulted in the release of radioactive materials into the environment. To provide further details regarding the distribution of air dose rate and the distribution of radioactive cesium ((134)Cs and (137)Cs) deposition on the ground within a radius of approximately 5 km from the nuclear power plant, we carried out measurements using an unmanned helicopter equipped with a radiation detection system. The distribution of the air dose rate at a height of 1 m above the ground and the radioactive cesium deposition on the ground was calculated. Accordingly, the footprint of radioactive plumes that extended from the FDNPP was illustrated. Copyright © 2014 Elsevier Ltd. All rights reserved.

Reducing environmental damage through the use of unmanned aerial vehicles as the best available technology

NASA Astrophysics Data System (ADS)

Fedulova, E. A.; Akulov, A. O.; Rada, A. O.; Alabina, T. A.; Savina, Ju Ju

2018-01-01

The article examines the possibilities of using unmanned aerial vehicles as the best available technologies in the field of agriculture and mining. The object of the study is the use of unmanned aerial vehicles as the best available technology. The main areas of application of this technology are identified: agro technical operations, aerial photography of mining operations. The technology of unmanned aerial vehicles is compared with the technologies of ground agricultural machinery. The research methodology includes an expert evaluation of the unmanned aerial vehicle technology belonging to the class of the best available technologies by the criteria: the level of environmental impact, resource saving, the use of low-waste, non-waste processes, the existence of at least two objects, economic efficiency. Expert evaluations were processed using the apparatus of fuzzy sets, which make it possible to construct membership functions. This allowed us to prove that the technology of unmanned aerial vehicles belongs to a fuzzy set of the best available technologies. The results of the research show that the use of unmanned aerial vehicles provides a saving of resources, especially non-renewable combustible minerals, reduces emissions and discharges of pollutants into the atmosphere, and also reduces soil erosion. Unmanned aerial vehicles should be included in the national directories of the best available technologies for the mining industry and agriculture.

48 CFR 252.228-7001 - Ground and flight risk.

Code of Federal Regulations, 2013 CFR

2013-10-01

... aircraft in the process of being manufactured, disassembled, or reassembled; provided that an engine... airships, unmanned aerial vehicles, or other nonconventional aircraft specified in this contract. (2...

An Investigation of Multiple Unmanned Aircraft Systems Control from the Cockpit of an AH-64 Apache Helicopter

DTIC Science & Technology

2014-12-01

An Investigation of Multiple Unmanned Aircraft Systems Control from the Cockpit of an AH-64 Apache Helicopter by Jamison S Hicks and David B...estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense , Washington...infantrymen, aircraft pilots, or dedicated UAS ground control station (GCS) operators. The purpose of the UAS is to allow for longer and more discrete

48 CFR 252.228-7001 - Ground and flight risk.

Code of Federal Regulations, 2014 CFR

2014-10-01

... aircraft in the process of being manufactured, disassembled, or reassembled; provided that an engine... airships, unmanned aerial vehicles, or other nonconventional aircraft specified in this contract. (2...

48 CFR 252.228-7001 - Ground and flight risk.

Code of Federal Regulations, 2011 CFR

2011-10-01

... aircraft in the process of being manufactured, disassembled, or reassembled; provided that an engine... airships, unmanned aerial vehicles, or other nonconventional aircraft specified in this contract. (2...

48 CFR 252.228-7001 - Ground and flight risk.

Code of Federal Regulations, 2012 CFR

2012-10-01

... aircraft in the process of being manufactured, disassembled, or reassembled; provided that an engine... airships, unmanned aerial vehicles, or other nonconventional aircraft specified in this contract. (2...

Mission Planning for Tactical Aircraft (Preflight and In-Flight) (Systemes de Planification des Missions Pour Avions Tactiques) (Avant Vol et en Vol).

DTIC Science & Technology

1992-12-01

Ground-Based Mission Planning Systems 9 2.3 Networking Mission Planning Systems 11 2.4 Fully Automated Mission Planning I I 2.5 Unmanned Air Vehicles 13...Missile Engagement Zone RPV Remotely Piloted Vehicle MIDS Multifunction Information Distribution System RRDB Rapidly Reconfigurable Databus MIL-STD...Comrmantd OPORD Operations Order TV Television OPS Operational OR Operational Relationship UAV Unmanned Air Vehicle UAV Unnmanned Air Vehicle PA

Detail design of empennage of an unmanned aerial vehicle

NASA Astrophysics Data System (ADS)

Sarker, Md. Samad; Panday, Shoyon; Rasel, Md; Salam, Md. Abdus; Faisal, Kh. Md.; Farabi, Tanzimul Hasan

2017-12-01

In order to maintain the operational continuity of air defense systems, unmanned autonomous or remotely controlled unmanned aerial vehicle (UAV) plays a great role as a target for the anti-aircraft weapons. The aerial vehicle must comply with the requirements of high speed, remotely controlled tracking and navigational aids, operational sustainability and sufficient loiter time. It can also be used for aerial reconnaissance, ground surveillance and other intelligence operations. This paper aims to develop a complete tail design of an unmanned aerial vehicle using Systems Engineering approach. The design fulfils the requirements of longitudinal and directional trim, stability and control provided by the horizontal and vertical tail. Tail control surfaces are designed to provide sufficient control of the aircraft in critical conditions. Design parameters obtained from wing design are utilized in the tail design process as required. Through chronological calculations and successive iterations, optimum values of 26 tail design parameters are determined.

Apollo experience report: Guidance and control systems. Mission control programmer for unmanned missions AS-202, Apollo 4, and Apollo 6

NASA Technical Reports Server (NTRS)

Holloway, G. F.

1975-01-01

An unmanned test flight program required to evaluate the command module heat shield and the structural integrity of the command and service module/Saturn launch vehicle is described. The mission control programer was developed to provide the unmanned interface between the guidance and navigation computer and the other spacecraft systems for mission event sequencing and real-time ground control during missions AS-202, Apollo 4, and Apollo 6. The development of this unmanned programer is traced from the initial concept through the flight test phase. Detailed discussions of hardware development problems are given with the resulting solutions. The mission control programer functioned correctly without any flight anomalies for all missions. The Apollo 4 mission control programer was reused for the Apollo 6 flight, thus being one of the first subsystems to be reflown on an Apollo space flight.

Evaluating remotely sensed plant count accuracy with differing unmanned aircraft system altitudes, physical canopy separations, and ground covers

NASA Astrophysics Data System (ADS)

Leiva, Josue Nahun; Robbins, James; Saraswat, Dharmendra; She, Ying; Ehsani, Reza

2017-07-01

This study evaluated the effect of flight altitude and canopy separation of container-grown Fire Chief™ arborvitae (Thuja occidentalis L.) on counting accuracy. Images were taken at 6, 12, and 22 m above the ground using unmanned aircraft systems. Plants were spaced to achieve three canopy separation treatments: 5 cm between canopy edges, canopy edges touching, and 5 cm of canopy edge overlap. Plants were placed on two different ground covers: black fabric and gravel. A counting algorithm was trained using Feature Analyst®. Total counting error, false positives, and unidentified plants were reported for images analyzed. In general, total counting error was smaller when plants were fully separated. The effect of ground cover on counting accuracy varied with the counting algorithm. Total counting error for plants placed on gravel (-8) was larger than for those on a black fabric (-2), however, false positive counts were similar for black fabric (6) and gravel (6). Nevertheless, output images of plants placed on gravel did not show a negative effect due to the ground cover but was impacted by differences in image spatial resolution.

Department of Defense Joint Chemical and Biological Defense Program 2009 Annual Report to Congress

DTIC Science & Technology

2009-03-27

completion at the ECBC on the Edgewood Area of Aberdeen Proving Ground (APG), MD. The SRF is a collaborative effort, funded by the DoD, DHS, and...Accelerated Manufacture of Pharmaceuticals APB Acquisition Program Baseline APG Aberdeen Proving Ground ARC Annual Report to Congress ASC Active...Critical Reagents Program CUGV Chemical, Biological, Radiological, and Nuclear Unmanned Ground Vehicle CW Chemical Weapons CWA Chemical Warfare Agent CWC

Evaluation of Early Ground Control Station Configurations for Interacting with a UAS Traffic Management (UTM) System

NASA Technical Reports Server (NTRS)

Dao, Arik-Quang V.; Martin, Lynne; Mohlenbrink, Christoph; Bienert, Nancy; Wolte, Cynthia; Gomez, Ashley; Claudatos, Lauren; Mercer, Joey

2017-01-01

The purpose of this paper is to report on a human factors evaluation of ground control station design concepts for interacting with an unmanned traffic management system. The data collected for this paper comes from recent field tests for NASA's Unmanned Traffic Management (UTM) project, and covers the following topics; workload, situation awareness, as well as flight crew communication, coordination, and procedures. The goal of this evaluation was to determine if the various software implementations for interacting with the UTM system can be described and classified into design concepts to provide guidance for the development of future UTM interfaces. We begin with a brief description of NASA's UTM project, followed by a description of the test range configuration related to a second development phase. We identified (post hoc) two classes in which the ground control stations could be grouped. This grouping was based on level of display integration. The analysis was exploratory and informal. It was conducted to compare ground stations across those two classes and against the aforementioned topics. Herein, we discuss the results.

Unmanned aerial vehicle-based structure from motion biomass inventory estimates

NASA Astrophysics Data System (ADS)

Bedell, Emily; Leslie, Monique; Fankhauser, Katie; Burnett, Jonathan; Wing, Michael G.; Thomas, Evan A.

2017-04-01

Riparian vegetation restoration efforts require cost-effective, accurate, and replicable impact assessments. We present a method to use an unmanned aerial vehicle (UAV) equipped with a GoPro digital camera to collect photogrammetric data of a 0.8-ha riparian restoration. A three-dimensional point cloud was created from the photos using "structure from motion" techniques. The point cloud was analyzed and compared to traditional, ground-based monitoring techniques. Ground-truth data were collected on 6.3% of the study site and averaged across the entire site to report stem heights in stems/ha in three height classes. The project site was divided into four analysis sections, one for derivation of parameters used in the UAV data analysis and the remaining three sections reserved for method validation. Comparing the ground-truth data to the UAV generated data produced an overall error of 21.6% and indicated an R2 value of 0.98. A Bland-Altman analysis indicated a 95% probability that the UAV stems/section result will be within 61 stems/section of the ground-truth data. The ground-truth data are reported with an 80% confidence interval of ±1032 stems/ha thus, the UAV was able to estimate stems well within this confidence interval.

Human Systems Integration for Network Centric Warfare (Integration des systemes humains dans les operations reseaux centrees)

DTIC Science & Technology

2010-02-01

Combat System (MCS) or Medical Vehicle Treatment (MV- T ), A for unmanned aerial vehicles such as Class II, and G for unmanned ground vehicles the...effective co-ordination with other NATO bodies involved in R& T activities. RTO reports both to the Military Committee of NATO and to the Conference of...research is one of the more promising areas of co-operation. The total spectrum of R& T activities is covered by the following 7 bodies: • AVT Applied

Applying Unmanned Ground Vehicle Technologies To Unmanned Surface Vehicles

DTIC Science & Technology

2005-01-01

PCI or ISA bus interface • 7 UARTs • 3 USB ports • CAN bus • I2C Bus • 1 RS232 Serial Port • Two 12-bit D-A output • Two 8-bit D-A...two of the seven UARTs and the CAN bus interface. It is also used to preprocess some sensor data before sending it to the FPGA. The daughterboard...modification of the Kalman Filter and PID parameters for use in a marine environment. 2.2.1 Architecture The Small Robot Technology ( SMART ) software

Autonomy, Unmanned Ground Vehicles, and the U.S. Army: Preparing for the Future by Examining the Past

DTIC Science & Technology

2009-05-01

gathers wisdom. – Isaac Asimov As a result of the National Defense Authorization Act (NDAA) of 2001, Congress signed into law a mandate for the...Monroe, December 2007), 14-15. 13 Isaac Asimov ,. How Did We Find Out About Robots? (New York: Walker and Company, 1984), 25-26. 14 Webster‟s Third...2007): 79-89. Asimov , Isaac. How Did We Find Out About Robots? New York: Walker and Company, 1984. Autonomy Levels for Unmanned Systems Working

mapKITE: a New Paradigm for Simultaneous Aerial and Terrestrial Geodata Acquisition and Mapping

NASA Astrophysics Data System (ADS)

Molina, P.; Blázquez, M.; Sastre, J.; Colomina, I.

2016-06-01

We introduce a new mobile, simultaneous terrestrial and aerial, geodata collection and post-processing method: mapKITE. By combining two mapping technologies such as terrestrial mobile mapping and unmanned aircraft aerial mapping, geodata are simultaneously acquired from air and ground. More in detail, a mapKITE geodata acquisition system consists on an unmanned aircraft and a terrestrial vehicle, which hosts the ground control station. By means of a real-time navigation system on the terrestrial vehicle, real-time waypoints are sent to the aircraft from the ground. By doing so, the aircraft is linked to the terrestrial vehicle through a "virtual tether," acting as a "mapping kite." In the article, we entail the concept of mapKITE as well as the various technologies and techniques involved, from aircraft guidance and navigation based on IMU and GNSS, optical cameras for mapping and tracking, sensor orientation and calibration, etc. Moreover, we report of a new measurement introduced in mapKITE, that is, point-and-scale photogrammetric measurements [of image coordinates and scale] for optical targets of known size installed on the ground vehicle roof. By means of accurate posteriori trajectory determination of the terrestrial vehicle, mapKITE benefits then from kinematic ground control points which are photogrametrically observed by point-and-scale measures. Initial results for simulated configurations show that these measurements added to the usual Integrated Sensor Orientation ones reduce or even eliminate the need of conventional ground control points -therefore, lowering mission costs- and enable selfcalibration of the unmanned aircraft interior orientation parameters in corridor configurations, in contrast to the situation of traditional corridor configurations. Finally, we report about current developments of the first mapKITE prototype, developed under the European Union Research and Innovation programme Horizon 2020. The first mapKITE mission will be held at the BCN Drone Center (Collsuspina, Moià, Spain) in mid 2016.

Systems Engineering of Unmanned DoD Systems: Following the Joint Capabilities Integration and Development System/Defense Acquisition System Process to Develop an Unmanned Ground Vehicle System

DTIC Science & Technology

2015-12-01

Manual D-A-1). APAs are “Performance attributes of a system not important enough to be considered KPPs or KSAs, but still appropriate to include in...the CDD or CPD are designated as APAs ” (JCIDS Manual D-A-1). The requirements are expressed using Thresholds (T) and Objectives (O). “Performance...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA SYSTEMS ENGINEERING CAPSTONE PROJECT REPORT Approved for public release; distribution is

Comparative aerial- and ground-based high-throughput phenotyping for the genetic dissection of NDVI as a proxy for drought-adaptive traits in durum wheat

USDA-ARS?s Scientific Manuscript database

High-throughput phenotyping platforms (HTPPs) provide novel opportunities to more effectively dissect the genetic basis of drought-adaptive traits. This genome-wide association study (GWAS) compares the results obtained with two Unmanned Aerial Vehicles (UAVs) and a ground-based platform used to mea...

Infrared stereo calibration for unmanned ground vehicle navigation

NASA Astrophysics Data System (ADS)

Harguess, Josh; Strange, Shawn

2014-06-01

The problem of calibrating two color cameras as a stereo pair has been heavily researched and many off-the-shelf software packages, such as Robot Operating System and OpenCV, include calibration routines that work in most cases. However, the problem of calibrating two infrared (IR) cameras for the purposes of sensor fusion and point could generation is relatively new and many challenges exist. We present a comparison of color camera and IR camera stereo calibration using data from an unmanned ground vehicle. There are two main challenges in IR stereo calibration; the calibration board (material, design, etc.) and the accuracy of calibration pattern detection. We present our analysis of these challenges along with our IR stereo calibration methodology. Finally, we present our results both visually and analytically with computed reprojection errors.

An Analysis of the First Fifteen Years of the Department of Defense Framework for Unmanned Ground Systems

DTIC Science & Technology

2014-12-01

1995 ..............................................78  g.  JAUGS 1995 ............................................................................82  h...108  g.  JAUGS from 1995 to 1996 ....................................................111  h.  Conclusion...2001 .......................................172  j.  JAUGS 2001 ..........................................................................173  k

UAVs - Current Situation and Considerations for the Way Forward

DTIC Science & Technology

2000-04-01

and UGV command and control relay. Examples Altus, Hermes 1500, Heron (EagleStar), I.GNAT, Perseus, Predator, Theseus The arrival of shipborne VTOL...Silver Arrow, Israel), Theseus (Aurora Flight Scien- RPB-35 ces, USA). , - Airspeed Airships, UK AS-A100 & 400 / AS-600 & 800 - Automation Institute

Comparative Hepatoprotective Effect of Vitamins A and E Against Gasoline Vapor Toxicity in Male and Female Rats

PubMed Central

Uboh, Friday Effiong; Ebong, Patrick E.; Umoh, Ime B.

2009-01-01

Background Plasma alanine transferase(ALT), aspartate transferase(AST), α-glutamyl transferase(GGT), and alkaline phosphatase(ALP) activities are known biomarkers in assessing hepatic functional integrity. A remarkable rise in the activities of these enzymes normally signifies hepatotoxicity of chemical agent(s) in the biological system. Exposure to 17.8 cm3h-1m-3 of PMS blend unleaded gasoline vapors (UGV) for 6 hr/day, 5 days/week for 20 weeks have been reported to cause hepatotoxicity in rats. Methods In this study, the comparative hepatoprotective effect of vitamins A (retinol) and E (α-tocopherol) against UGV-induced toxicity was assessed in male and female rats. Retinol and α-tocopherol at prophylactic dosage (400 and 200 IU/kg/day, respectively) were separately administered orally to the test rats concomitant with exposure to UGV in the last two weeks of the experiment. Results The results of this study indicated that exposure to UGV caused significant increase (P < 0.05) in the activities of serum ALT, AST, ALP, GGT and bilirubin in male and female rats. Oral administration of prophylactic doses of retinol and α-tocopherol produced a significant decrease (P < 0.05) in the activities of these parameters in male and female test rats, compared with the non-treated test rats; but insignificant increase(P ≥ 0.05), compared with the control. However, the hepatoprotective effect of α-tocopherol was observed to be more potent than that of retinol. Conclusions The result of this study demonstrated that the hepatoprotective potency of α-tocopherol against gasoline vapors toxicity was higher than that of retinol in male and female rats, although the female gender of the animal model responded to treatment with both vitamins better than the males. Hence, the work suggested the beneficial effects of both vitamins against hepatotoxicity in individuals frequently exposed to gasoline vapors. PMID:27956974

International Assessment of Unmanned Ground Vehicles

DTIC Science & Technology

2008-02-01

research relevant to ground robotics include • Multi-sensor data fusion • Stereovision • Dedicated robots, including legged robots, tracked robots...Technology Laboratory has developed several mobile robots with leg - ged, wheeled, rolling, rowing, and hybrid locomotion. Areas of particular emphasis...117 UK Department of Trade and Industry ( DTI ) Global Watch Mission. November 2006. Mechatronics in Russia. 118 CRDI Web Site: http

Accuracy Assessment of Professional Grade Unmanned Systems for High Precision Airborne Mapping

NASA Astrophysics Data System (ADS)

Mostafa, M. M. R.

2017-08-01

Recently, sophisticated multi-sensor systems have been implemented on-board modern Unmanned Aerial Systems. This allows for producing a variety of mapping products for different mapping applications. The resulting accuracies match the traditional well engineered manned systems. This paper presents the results of a geometric accuracy assessment project for unmanned systems equipped with multi-sensor systems for direct georeferencing purposes. There are a number of parameters that either individually or collectively affect the quality and accuracy of a final airborne mapping product. This paper focuses on identifying and explaining these parameters and their mutual interaction and correlation. Accuracy Assessment of the final ground object positioning accuracy is presented through real-world 8 flight missions that were flown in Quebec, Canada. The achievable precision of map production is addressed in some detail.

Hydrology with unmanned aerial vehicles (UAVs)

USDA-ARS?s Scientific Manuscript database

Hydrologic remote sensing currently depends on expensive and infrequent aircraft observations for validation of operational satellite products, typically conducted during field campaigns that also include ground-based measurements. With the advent of new, hydrologically-relevant satellite missions, ...

An Innovative Unmanned System for Advanced Environmental Monitoring: Design and Development

NASA Astrophysics Data System (ADS)

Marsella, Ennio; Giordano, Laura; Evangelista, Lorenza; Iengo, Antonio; di Filippo, Alessandro; Coppola, Aniello

2015-04-01

The paper summarizes the design and development of a new technology and tools for real-time coordination and control of unmanned vehicles for advanced environmental monitoring. A new Unmanned System has been developed at Institute for Coastal Marine Environmental - National Research Council (Italy), in the framework of two National Operational Programs (PON): Technological Platform for Geophysical and Environmental Marine Survey-PITAM and Integrated Systems and Technologies for Geophysical and Environmental Monitoring in coastal-marine areas-STIGEAC. In particular, the system includes one Unmanned Aerial Vehicle (UAV) and two Unmanned Marine Vehicles (UMV). Major innovations concern the implementation of a new architecture to control each drone and/or to allow the cooperation between heterogeneous vehicles, the integration of distributed sensing techniques and real-time image processing capabilities. Part of the research in these projects involves, therefore, an architecture, where the ground operator can communicate with the Unmanned Vehicles at various levels of abstraction using pointing devices and video viewing. In detail, a Ground Control Station (GCS) has been design and developed to allow the government in security of the drones within a distance up to twenty kilometers for air explorations and within ten nautical miles for marine activities. The Ground Control Station has the following features: 1. hardware / software system for the definition of the mission profiles; 3. autonomous and semi-autonomous control system by remote control (joystick or other) for the UAV and UMVs; 4. integrated control system with comprehensive visualization capabilities, monitoring and archiving of real-time data acquired from scientific payload; 5. open structure to future additions of systems, sensors and / or additional vehicles. In detail, the UAV architecture is a dual-rotor, with an endurance ranging from 55 to 200 minutes, depending on payload weight (maximum 26 kg) and wind conditions, and a capability to survey an area of up to 5x5 square kilometers. The UAV payload consists of three different types of sensors: a laser scanner, a thermal-camera and an integrated camera reflex with gimbal. The laser scanner has 10 mm survey-grade accuracy and a field of view up to 330°. The thermal-camera has a resolution 640x480 pixels and a thermal sensitivity <20 mK (at 30 °C), while the reflex is a 22.3 Megapixel full-frame sensor. In addition to the common applications, such as generating mapping, charting, and geodesy products, the system allows performing real-time survey and monitoring of different natural risk under dangerous condition. The system is, also, address to environmental risk monitoring and prevention, industrial activity and emergency interventions related to environmental crises (i.e. oil spills).

Systems engineering and integration of control centers in support of multiple programs. [ground control for STS payloads and unmanned vehicles

NASA Technical Reports Server (NTRS)

Miller, David N.

1989-01-01

The NASA Johnson Space Center's new Multiprogram Control Center (MPCC) addresses the control requirements of complex STS payloads as well as unmanned vehicles. An account is given of the relationship of the MPCC to the STS Mission Control Center, with a view to significant difficulties that may be encountered and solutions thus far devised for generic problems. Examples of MPCC workstation applications encompass telemetry decommutation, engineering unit conversion, data-base management, trajectory processing, and flight design.

Developing Performance Measures for Manned-Unmanned Teaming Skills

DTIC Science & Technology

2015-02-01

Moves aircraft to safe area Utilize standardized radio communication and signal operating procedures Perform BDA Utilize Standard report formats...UAS does not conduct BDA ; assumes target is destroyed without verification UAS evaluates target; reports BDA to engaging aircraft (or...ground unit) after prompting UAS evaluates target; proactively reports BDA to engaging aircraft (or ground unit) 1 2 3 4 5 1 2 3 4 5 B

NASA Flight Operations of Ikhana and Global Hawk

NASA Technical Reports Server (NTRS)

Posada, Herman

2010-01-01

This slide presentation reviews the flight operations for NASA's Ikhana and Globalhawk unmanned aerial vehicles. It includes information on the ground support systems, vehicle specifications, payloads, mission planning and the 2007 Western States Fire Mission Objectives.

Path Planning Algorithms for Autonomous Border Patrol Vehicles

NASA Astrophysics Data System (ADS)

Lau, George Tin Lam

This thesis presents an online path planning algorithm developed for unmanned vehicles in charge of autonomous border patrol. In this Pursuit-Evasion game, the unmanned vehicle is required to capture multiple trespassers on its own before any of them reach a target safe house where they are safe from capture. The problem formulation is based on Isaacs' Target Guarding problem, but extended to the case of multiple evaders. The proposed path planning method is based on Rapidly-exploring random trees (RRT) and is capable of producing trajectories within several seconds to capture 2 or 3 evaders. Simulations are carried out to demonstrate that the resulting trajectories approach the optimal solution produced by a nonlinear programming-based numerical optimal control solver. Experiments are also conducted on unmanned ground vehicles to show the feasibility of implementing the proposed online path planning algorithm on physical applications.

Precision wildlife monitoring using unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Hodgson, Jarrod C.; Baylis, Shane M.; Mott, Rowan; Herrod, Ashley; Clarke, Rohan H.

2016-03-01

Unmanned aerial vehicles (UAVs) represent a new frontier in environmental research. Their use has the potential to revolutionise the field if they prove capable of improving data quality or the ease with which data are collected beyond traditional methods. We apply UAV technology to wildlife monitoring in tropical and polar environments and demonstrate that UAV-derived counts of colony nesting birds are an order of magnitude more precise than traditional ground counts. The increased count precision afforded by UAVs, along with their ability to survey hard-to-reach populations and places, will likely drive many wildlife monitoring projects that rely on population counts to transition from traditional methods to UAV technology. Careful consideration will be required to ensure the coherence of historic data sets with new UAV-derived data and we propose a method for determining the number of duplicated (concurrent UAV and ground counts) sampling points needed to achieve data compatibility.

Autonomous urban reconnaissance ingress system (AURIS): providing a tactically relevant autonomous door-opening kit for unmanned ground vehicles

NASA Astrophysics Data System (ADS)

Shane, David J.; Rufo, Michael A.; Berkemeier, Matthew D.; Alberts, Joel A.

2012-06-01

The Autonomous Urban Reconnaissance Ingress System (AURIS™) addresses a significant limitation of current military and first responder robotics technology: the inability of reconnaissance robots to open doors. Leveraging user testing as a baseline, the program has derived specifications necessary for military personnel to open doors with fielded UGVs (Unmanned Ground Vehicles), and evaluates the technology's impact on operational mission areas: duration, timing, and user patience in developing a tactically relevant, safe, and effective system. Funding is provided through the US ARMY Tank Automotive Research, Development and Engineering Center (TARDEC) and the project represents a leap forward in perception, autonomy, robotic implements, and coordinated payload operation in UGVs. This paper describes high level details of specification generation, status of the last phase of development, an advanced view of the system autonomy capability, and a short look ahead towards the ongoing work on this compelling and important technology.

Medium Altitude Endurance Unmanned Air Vehicle

NASA Astrophysics Data System (ADS)

Ernst, Larry L.

1994-10-01

The medium altitude endurance unmanned air vehicle (MAE UAV) program (formerly the tactical endurance TE UAV) is a new effort initiated by the Department of Defense to develop a ground launched UAV that can fly out 500 miles, remain on station for 24 hours, and return. It will transmit high resolution optical, infrared, and synthetic aperture radar (SAR) images of well-defended target areas through satellite links. It will provide near-real-time, releasable, low cost/low risk surveillance, targeting and damage assessment complementary to that of satellites and manned aircraft. The paper describes specific objectives of the MAE UAV program (deliverables and schedule) and the program's unique position as one of several programs to streamline the acquisition process under the cognizance of the newly established Airborne Reconnaissance Office. I discuss the system requirements and operational concept and describe the technical capabilities and characteristics of the major subsystems (airframe, propulsion, navigation, sensors, communication links, ground station, etc.) in some detail.

Spaceflight tracking and data network operational reliability computer output for MTBF and availability. Appendix V to CSC-1-395

NASA Technical Reports Server (NTRS)

Seneca, V. I.; Mlynarczyk, R. H.

1974-01-01

Tables of data are provided to show the availability of Skylab data to selected ground stations during the phases of Skylab preflight, Skylab unmanned condition, and Skylab manned condition. The mean time between failure (MTBF) of the same Skylab functions is tabulated for the selected ground stations. All reliability data are based on a 90 percent confidence interval.

The Ethics of Robotic, Autonomous, and Unmanned Systems Technologies in Life Saving Roles

DTIC Science & Technology

2017-06-12

every day. The healthcare community is governed by esteemed practices such as moral self -governance, and other philosophical principles that define...1 movement of a casualty. These assets are under the purview of ground commanders, not the medical evacuation community .4 Thus, having... communications with ground personnel and will operate under supervisory control of any operator, requiring no specialized training.18 Also, ONR is investigating

Assessing land leveling needs and performance with unmanned aerial system

NASA Astrophysics Data System (ADS)

Enciso, Juan; Jung, Jinha; Chang, Anjin; Chavez, Jose Carlos; Yeom, Junho; Landivar, Juan; Cavazos, Gabriel

2018-01-01

Land leveling is the initial step for increasing irrigation efficiencies in surface irrigation systems. The objective of this paper was to evaluate potential utilization of an unmanned aerial system (UAS) equipped with a digital camera to map ground elevations of a grower's field and compare them with field measurements. A secondary objective was to use UAS data to obtain a digital terrain model before and after land leveling. UAS data were used to generate orthomosaic images and three-dimensional (3-D) point cloud data by applying the structure for motion algorithm to the images. Ground control points (GCPs) were established around the study area, and they were surveyed using a survey grade dual-frequency GPS unit for accurate georeferencing of the geospatial data products. A digital surface model (DSM) was then generated from the 3-D point cloud data before and after laser leveling to determine the topography before and after the leveling. The UAS-derived DSM was compared with terrain elevation measurements acquired from land surveying equipment for validation. Although 0.3% error or root mean square error of 0.11 m was observed between UAS derived and ground measured ground elevation data, the results indicated that UAS could be an efficient method for determining terrain elevation with an acceptable accuracy when there are no plants on the ground, and it can be used to assess the performance of a land leveling project.

Dynamics of omnidirectional unmanned rescue vehicle with mecanum wheels

NASA Astrophysics Data System (ADS)

Typiak, Andrzej; Łopatka, Marian Janusz; Rykała, Łukasz; Kijek, Magdalena

2018-01-01

The work presents the dynamic equations of motion of a unmanned six-wheeled vehicle with mecanum wheels for rescue applications derived with the of Lagrange equations of the second kind with multipliers. Analysed vehicle through using mecanum wheels has three degrees of freedom and can move on a flat ground in any direction with any configuration of platform's frame. In order to derive dynamic equations of motion of mentioned object, kinetic potential of the system and generalized forces affecting the system are determined. The results of a solution of inverse dynamics problem are also published.

RQ-21A Blackjack Small Tactical Unmanned Aircraft System (STUAS): Initial Operational Test and Evaluation Report

DTIC Science & Technology

2015-06-29

requirements for the system’s ground components to the generating capabilities of standard Marine Corps generators ). The Navy did not fully address two...dedicated generators to power the ground control stations. Recommendations The Navy and Marine Corps should consider the following recommendations in...components to the generating capabilities of standard Marine Corps generators ). The Navy did not fully address two recommendations (strengthening

Development of an Unmanned Aircraft System and Cyberinfrastructure for Environmental Science Research

NASA Astrophysics Data System (ADS)

Brady, J. J.; Tweedie, C. E.; Escapita, I. J.

2009-12-01

There is a fundamental need to improve capacities for monitoring environmental change using remote sensing technologies. Recently, researchers have begun using Unmanned Aerial Vehicles (UAVs) to expand and improve upon remote sensing capabilities. Limitations to most non-military and relatively small-scale Unmanned Aircraft Systems (UASs) include a need to develop more reliable communications between ground and aircraft, tools to optimize flight control, real time data processing, and visually ascertaining the quantity of data collected while in air. Here we present a prototype software system that has enhanced communication between ground and the vehicle, can synthesize near real time data acquired from sensors on board, can log operation data during flights, and can visually demonstrate the amount and quality of data for a sampling area. This software has the capacity to greatly improve the utilization of UAS in the environmental sciences. The software system is being designed for use on a paraglider UAV that has a suite of sensors suitable for characterizing the footprints of eddy covariance towers situated in the Chihuahuan Desert and in the Arctic. Sensors on board relay operational flight data (airspeed, ground speed, latitude, longitude, pitch, yaw, roll, acceleration, and video) as well as a suite of customized sensors. Additional sensors can be added to an on board laptop or a CR1000 data logger thereby allowing data from these sensors to be visualized in the prototype software. This poster will describe the development, use and customization of our UAS and multimedia will be available during AGU to illustrate the system in use. UAV on workbench in the lab UAV in flight

Velodyne HDL-64E lidar for unmanned surface vehicle obstacle detection

NASA Astrophysics Data System (ADS)

Halterman, Ryan; Bruch, Michael

2010-04-01

The Velodyne HDL-64E is a 64 laser 3D (360×26.8 degree) scanning LIDAR. It was designed to fill perception needs of DARPA Urban Challenge vehicles. As such, it was principally intended for ground use. This paper presents the performance of the HDL-64E as it relates to the marine environment for unmanned surface vehicle (USV) obstacle detection and avoidance. We describe the sensor's capacity for discerning relevant objects at sea- both through subjective observations of the raw data and through a rudimentary automated obstacle detection algorithm. We also discuss some of the complications that have arisen with the sensor.

A review of unmanned aircraft system ground risk models

NASA Astrophysics Data System (ADS)

Washington, Achim; Clothier, Reece A.; Silva, Jose

2017-11-01

There is much effort being directed towards the development of safety regulations for unmanned aircraft systems (UAS). National airworthiness authorities have advocated the adoption of a risk-based approach, whereby regulations are driven by the outcomes of a systematic process to assess and manage identified safety risks. Subsequently, models characterising the primary hazards associated with UAS operations have now become critical to the development of regulations and in turn, to the future of the industry. Key to the development of airworthiness regulations for UAS is a comprehensive understanding of the risks UAS operations pose to people and property on the ground. A comprehensive review of the literature identified 33 different models (and component sub models) used to estimate ground risk posed by UAS. These models comprise failure, impact location, recovery, stress, exposure, incident stress and harm sub-models. The underlying assumptions and treatment of uncertainties in each of these sub-models differ significantly between models, which can have a significant impact on the development of regulations. This paper reviews the state-of-the-art in research into UAS ground risk modelling, discusses how the various sub-models relate to the different components of the regulation, and explores how model-uncertainties potentially impact the development of regulations for UAS.

About infrared scanning of photovoltaic solar plant

NASA Astrophysics Data System (ADS)

Kauppinen, T.; Panouillot, P.-E.; Siikanen, S.; Athanasakou, E.; Baltas, P.; Nikopoulous, B.

2015-05-01

The paper is discussing about infrared scanning of PV solar plants. It is important that the performance of each solar panel and cell is verified. One new possibility compared to traditional ground-based scanning (handheld camera) is the utilization of UAV (Unmanned Aerial Vehicle). In this paper results from a PV solar Plant in Western Greece are introduced. The nominal power of the solar plants were 0, 9 MW and 2 MW and they were scanned both by a ground-controlled drone and by handheld equipment. It is essential to know all the factors effecting to results and also the time of scanning is important. The results done from the drone and from ground-based scanning are compared; also results from various altitudes and time of day are discussed. The UAV (Unmanned Aerial Vehicle/RPAS (Remote Piloted Aircraft Systems) will give an excellent opportunity to monitor various targets which are impossible or difficult to access from the ground. Compared to fixed-wing and helicopter-based platforms it will give advantages but also this technology has limitations. One limitation is the weight of the equipment and the short operational range and short flight time. Also valid procedures must be created for different solutions in the future. The most important thing, as in all infrared thermography applications, is the proper interpretation of results.

An Analysis of the Influence of Flight Parameters in the Generation of Unmanned Aerial Vehicle (UAV) Orthomosaicks to Survey Archaeological Areas.

PubMed

Mesas-Carrascosa, Francisco-Javier; Notario García, María Dolores; Meroño de Larriva, Jose Emilio; García-Ferrer, Alfonso

2016-11-01

This article describes the configuration and technical specifications of a multi-rotor unmanned aerial vehicle (UAV) using a red-green-blue (RGB) sensor for the acquisition of images needed for the production of orthomosaics to be used in archaeological applications. Several flight missions were programmed as follows: flight altitudes at 30, 40, 50, 60, 70 and 80 m above ground level; two forward and side overlap settings (80%-50% and 70%-40%); and the use, or lack thereof, of ground control points. These settings were chosen to analyze their influence on the spatial quality of orthomosaicked images processed by Inpho UASMaster (Trimble, CA, USA). Changes in illumination over the study area, its impact on flight duration, and how it relates to these settings is also considered. The combined effect of these parameters on spatial quality is presented as well, defining a ratio between ground sample distance of UAV images and expected root mean square of a UAV orthomosaick. The results indicate that a balance between all the proposed parameters is useful for optimizing mission planning and image processing, altitude above ground level (AGL) being main parameter because of its influence on root mean square error (RMSE).

An Analysis of the Influence of Flight Parameters in the Generation of Unmanned Aerial Vehicle (UAV) Orthomosaicks to Survey Archaeological Areas

PubMed Central

Mesas-Carrascosa, Francisco-Javier; Notario García, María Dolores; Meroño de Larriva, Jose Emilio; García-Ferrer, Alfonso

2016-01-01

This article describes the configuration and technical specifications of a multi-rotor unmanned aerial vehicle (UAV) using a red–green–blue (RGB) sensor for the acquisition of images needed for the production of orthomosaics to be used in archaeological applications. Several flight missions were programmed as follows: flight altitudes at 30, 40, 50, 60, 70 and 80 m above ground level; two forward and side overlap settings (80%–50% and 70%–40%); and the use, or lack thereof, of ground control points. These settings were chosen to analyze their influence on the spatial quality of orthomosaicked images processed by Inpho UASMaster (Trimble, CA, USA). Changes in illumination over the study area, its impact on flight duration, and how it relates to these settings is also considered. The combined effect of these parameters on spatial quality is presented as well, defining a ratio between ground sample distance of UAV images and expected root mean square of a UAV orthomosaick. The results indicate that a balance between all the proposed parameters is useful for optimizing mission planning and image processing, altitude above ground level (AGL) being main parameter because of its influence on root mean square error (RMSE). PMID:27809293

The Effectiveness of Drone Strikes in Counterinsurgency and Counterterrorism Campaigns

DTIC Science & Technology

2013-09-01

accurate missiles that have the ca- pacity to target individuals, automobiles , and sections of structures such as rooms in a large house. Perhaps the...unmanned aerial ve- hicles (UAVs) or remotely piloted aircraft (RPAs)—are pilotless aircraft controlled by individuals located on the ground, often some...with many of the advantages that ground forces offer in counterinsurgency operations. The fact that drones are pilotless means that their use does

Collaborative engagement experiment

NASA Astrophysics Data System (ADS)

Mullens, Katherine; Troyer, Bradley; Wade, Robert; Skibba, Brian; Dunn, Michael

2006-05-01

Unmanned ground and air systems operating in collaboration have the potential to provide future Joint Forces a significant capability for operations in complex terrain. Collaborative Engagement Experiment (CEE) is a consolidation of separate Air Force, Army and Navy collaborative efforts within the Joint Robotics Program (JRP) to provide a picture of the future of unmanned warfare. The Air Force Research Laboratory (AFRL), Material and Manufacturing Directorate, Aerospace Expeditionary Force Division, Force Protection Branch (AFRL/MLQF), The Army Aviation and Missile Research, Development and Engineering Center (AMRDEC) Joint Technology Center (JTC)/Systems Integration Laboratory (SIL), and the Space and Naval Warfare Systems Center - San Diego (SSC San Diego) are conducting technical research and proof of principle experiments for an envisioned operational concept for extended range, three dimensional, collaborative operations between unmanned systems, with enhanced situational awareness for lethal operations in complex terrain. This paper describes the work by these organizations to date and outlines some of the plans for future work.

Human-Robot Teaming for Hydrologic Data Gathering at Multiple Scales

NASA Astrophysics Data System (ADS)

Peschel, J.; Young, S. N.

2017-12-01

The use of personal robot-assistive technology by researchers and practitioners for hydrologic data gathering has grown in recent years as barriers to platform capability, cost, and human-robot interaction have been overcome. One consequence to this growth is a broad availability of unmanned platforms that might or might not be suitable for a specific hydrologic investigation. Through multiple field studies, a set of recommendations has been developed to help guide novice through experienced users in choosing the appropriate unmanned platforms for a given application. This talk will present a series of hydrologic data sets gathered using a human-robot teaming approach that has leveraged unmanned aerial, ground, and surface vehicles over multiple scales. The field case studies discussed will be connected to the best practices, also provided in the presentation. This talk will be of interest to geoscience researchers and practitioners, in general, as well as those working in fields related to emerging technologies.

The carbon or silicon colonization of the universe?

PubMed

Parkinson, Bob

2005-01-01

At the time of the Apollo Programme, a first human mission to Mars was proposed as early as 1984 with the argument that the higher costs of human exploration would be more than justified by the increased effectiveness of human explorers. This was based on the Apollo experience, where "ground truth" measurements and sampling provided the basis for subsequent unmanned exploration of the Solar System. A human Mars mission is now not seen until 2030, at the end of a series of increasingly sophisticated unmanned probes. Each robot mission not only teaches us something about Mars, but also through experience increases our capabilities for the unmanned exploration of that planet. As a consequence, what a human mission would have to do becomes progressively more demanding. Any extended plan for the human exploration of Space will tend to be overtaken by advances in technology, and if this is not factored into the scenario the proposals will become progressively unrealistic.

Atmospheric Aerosol Sampling with Unmanned Aircraft Systems (UAS) in Alaska: Instrument Development, Payload Integration, and Measurement Campaigns

NASA Astrophysics Data System (ADS)

Barberie, S. R.; Saiet, E., II; Hatfield, M. C.; Cahill, C. F.

2014-12-01

Atmospheric aerosols remain one of biggest variables in understanding global climate. The number of feedback loops involved in aerosol processes lead to nonlinear behavior at the systems level, making confident modeling and prediction difficult. It is therefore important to ground-truth and supplement modeling efforts with rigorous empirical measurements. To this end, the Alaska Center for Unmanned Aircraft Systems Integration (ACUASI) at the University of Alaska Fairbanks has developed a new cascade DRUM-style impactor to be mounted aboard a variety of unmanned aircraft and work in tandem with an optical particle counter for the routine collection of atmospheric aerosols. These UAS-based aerosol samplers will be employed for measurement campaigns in traditionally hazardous conditions such as volcanic plumes and over forest fires. Here we report on the development and laboratory calibration of the new instrument, the integration with UAS, and the vertical profiling campaigns being undertaken.

A Multiresolution Experiment to Enable Impacts of High Fidelity Environments on Unmanned Ground Vehicle Representation

DTIC Science & Technology

2009-06-01

Center Geotechnical and Structures Laboratory (ERDC-GSL). Their contributions include the technical integration work of ANVEL , OneSAF, and MATREX...6  3.1  ANVEL Overview...15  4.4.3.  OneSAF Tasks ................................................................................. 16  4.4.4.  OneSAF/ ANVEL Scenario Execution

Unmanned Aerial Vehicles Master Plan, 1994. Master Plan.

DTIC Science & Technology

1994-05-31

Terminal SINCGARS = Single-Channel Ground and Airborne Radio System Figure 3-5 Maneuver Variant CONOPS I Psychological operations. deployment with early...650 KM DAT M 3 K (300 DESIRED) BEYOND FORWARD LINE OF OWN TROOPS (FLOT) APPROXIMATE RADIUS OF ACTION LEGEND ATARS = Advanced Tactical Air

Pheromone-based coordination strategy to static sensors on the ground and unmanned aerial vehicles carried sensors

NASA Astrophysics Data System (ADS)

Pignaton de Freitas, Edison; Heimfarth, Tales; Pereira, Carlos Eduardo; Morado Ferreira, Armando; Rech Wagner, Flávio; Larsson, Tony

2010-04-01

A current trend that is gaining strength in the wireless sensor network area is the use of heterogeneous sensor nodes in one coordinated overall network, needed to fulfill the requirements of sophisticated emerging applications, such as area surveillance systems. One of the main concerns when developing such sensor networks is how to provide coordination among the heterogeneous nodes, in order to enable them to efficiently respond the user needs. This study presents an investigation of strategies to coordinate a set of static sensor nodes on the ground cooperating with wirelessly connected Unmanned Aerial Vehicles (UAVs) carrying a variety of sensors, in order to provide efficient surveillance over an area of interest. The sensor nodes on the ground are set to issue alarms on the occurrence of a given event of interest, e.g. entrance of a non-authorized vehicle in the area, while the UAVs receive the issued alarms and have to decide which of them is the most suitable to handle the issued alarm. A bio-inspired coordination strategy based on the concept of pheromones is presented. As a complement of this strategy, a utility-based decision making approach is proposed.

Concept and realization of unmanned aerial system with different modes of operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Czyba, Roman; Szafrański, Grzegorz; Janusz, Wojciech

2014-12-10

In this paper we describe the development process of unmanned aerial system, its mechanical components, electronics and software solutions. During the stage of design, we have formulated some necessary requirements for the multirotor vehicle and ground control station in order to build an optimal system which can be used for the reconnaissance missions. Platform is controlled by use of the ground control station (GCS) and has possibility of accomplishing video based observation tasks. In order to fulfill this requirement the on-board payload consists of mechanically stabilized camera augmented with machine vision algorithms to enable object tracking tasks. Novelty of themore » system are four modes of flight, which give full functionality of the developed UAV system. Designed ground control station is consisted not only of the application itself, but also a built-in dedicated components located inside the chassis, which together creates an advanced UAV system supporting the control and management of the flight. Mechanical part of quadrotor is designed to ensure its robustness while meeting objectives of minimizing weight of the platform. Finally the designed electronics allows for implementation of control and estimation algorithms without the needs for their excessive computational optimization.« less

Algorithms for Heterogeneous, Multiple Depot, Multiple Unmanned Vehicle Path Planning Problems

DOE PAGES

Sundar, Kaarthik; Rathinam, Sivakumar

2016-12-26

Unmanned vehicles, both aerial and ground, are being used in several monitoring applications to collect data from a set of targets. This article addresses a problem where a group of heterogeneous aerial or ground vehicles with different motion constraints located at distinct depots visit a set of targets. The vehicles also may be equipped with different sensors, and therefore, a target may not be visited by any vehicle. The objective is to find an optimal path for each vehicle starting and ending at its respective depot such that each target is visited at least once by some vehicle, the vehicle–targetmore » constraints are satisfied, and the sum of the length of the paths for all the vehicles is minimized. Two variants of this problem are formulated (one for ground vehicles and another for aerial vehicles) as mixed-integer linear programs and a branchand- cut algorithm is developed to compute an optimal solution to each of the variants. Computational results show that optimal solutions for problems involving 100 targets and 5 vehicles can be obtained within 300 seconds on average, further corroborating the effectiveness of the proposed approach.« less

Cadastral Audit and Assessments Using Unmanned Aerial Systems

NASA Astrophysics Data System (ADS)

Cunningham, K.; Walker, G.; Stahlke, E.; Wilson, R.

2011-09-01

Ground surveys and remote sensing are integral to establishing fair and equitable property valuations necessary for real property taxation. The International Association of Assessing Officers (IAAO) has embraced aerial and street-view imaging as part of its standards related to property tax assessments and audits. New technologies, including unmanned aerial systems (UAS) paired with imaging sensors, will become more common as local governments work to ensure their cadastre and tax rolls are both accurate and complete. Trends in mapping technology have seen an evolution in platforms from large, expensive manned aircraft to very small, inexpensive UAS. Traditional methods of photogrammetry have also given way to new equipment and sensors: digital cameras, infrared imagers, light detection and ranging (LiDAR) laser scanners, and now synthetic aperture radar (SAR). At the University of Alaska Fairbanks (UAF), we work extensively with unmanned aerial systems equipped with each of these newer sensors. UAF has significant experience flying unmanned systems in the US National Airspace, having begun in 1969 with scientific rockets and expanded to unmanned aircraft in 2003. Ongoing field experience allows UAF to partner effectively with outside organizations to test and develop leading-edge research in UAS and remote sensing. This presentation will discuss our research related to various sensors and payloads for mapping. We will also share our experience with UAS and optical systems for creating some of the first cadastral surveys in rural Alaska.

Unmanned Aerial Vehicle (UAV) associated DTM quality evaluation and hazard assessment

NASA Astrophysics Data System (ADS)

Huang, Mei-Jen; Chen, Shao-Der; Chao, Yu-Jui; Chiang, Yi-Lin; Chang, Kuo-Jen

2014-05-01

Taiwan, due to the high seismicity and high annual rainfall, numerous landslides triggered every year and severe impacts affect the island. Concerning to the catastrophic landslides, the key information of landslide, including range of landslide, volume estimation and the subsequent evolution are important when analyzing the triggering mechanism, hazard assessment and mitigation. Thus, the morphological analysis gives a general overview for the landslides and been considered as one of the most fundamental information. We try to integrate several technologies, especially by Unmanned Aerial Vehicle (UAV) and multi-spectral camera, to decipher the consequence and the potential hazard, and the social impact. In recent years, the remote sensing technology improves rapidly, providing a wide range of image, essential and precious information. Benefited of the advancing of informatics, remote-sensing and electric technologies, the Unmanned Aerial Vehicle (UAV) photogrammetry mas been improve significantly. The study tries to integrate several methods, including, 1) Remote-sensing images gathered by Unmanned Aerial Vehicle (UAV) and by aerial photos taken in different periods; 2) field in-situ geologic investigation; 3) Differential GPS, RTK GPS and Ground LiDAR field in-site geoinfomatics measurements; 4) Construct the DTMs before and after landslide, as well as the subsequent periods using UAV and aerial photos; 5) Discrete element method should be applied to understand the geomaterial composing the slope failure, for predicting earthquake-induced and rainfall-induced landslides displacement. First at all, we evaluate the Microdrones MD4-1000 UAV airphotos derived Digital Terrain Model (DTM). The ground resolution of the DSM point cloud of could be as high as 10 cm. By integrated 4 ground control point within an area of 56 hectares, compared with LiDAR DSM and filed RTK-GPS surveying, the mean error is as low as 6cm with a standard deviation of 17cm. The quality of the UAV DSM could be as good as LiDAR data, and is ready for other applications. The quality of the data set provides not only geoinfomatics and GIS dataset of the hazards, but also for essential geomorphologic information for other study, and for hazard mitigation and planning, as well.

High-Throughput Phenotyping of Plant Height: Comparing Unmanned Aerial Vehicles and Ground LiDAR Estimates.

PubMed

Madec, Simon; Baret, Fred; de Solan, Benoît; Thomas, Samuel; Dutartre, Dan; Jezequel, Stéphane; Hemmerlé, Matthieu; Colombeau, Gallian; Comar, Alexis

2017-01-01

The capacity of LiDAR and Unmanned Aerial Vehicles (UAVs) to provide plant height estimates as a high-throughput plant phenotyping trait was explored. An experiment over wheat genotypes conducted under well watered and water stress modalities was conducted. Frequent LiDAR measurements were performed along the growth cycle using a phénomobile unmanned ground vehicle. UAV equipped with a high resolution RGB camera was flying the experiment several times to retrieve the digital surface model from structure from motion techniques. Both techniques provide a 3D dense point cloud from which the plant height can be estimated. Plant height first defined as the z -value for which 99.5% of the points of the dense cloud are below. This provides good consistency with manual measurements of plant height (RMSE = 3.5 cm) while minimizing the variability along each microplot. Results show that LiDAR and structure from motion plant height values are always consistent. However, a slight under-estimation is observed for structure from motion techniques, in relation with the coarser spatial resolution of UAV imagery and the limited penetration capacity of structure from motion as compared to LiDAR. Very high heritability values ( H 2 > 0.90) were found for both techniques when lodging was not present. The dynamics of plant height shows that it carries pertinent information regarding the period and magnitude of the plant stress. Further, the date when the maximum plant height is reached was found to be very heritable ( H 2 > 0.88) and a good proxy of the flowering stage. Finally, the capacity of plant height as a proxy for total above ground biomass and yield is discussed.

High-Throughput Phenotyping of Plant Height: Comparing Unmanned Aerial Vehicles and Ground LiDAR Estimates

PubMed Central

Madec, Simon; Baret, Fred; de Solan, Benoît; Thomas, Samuel; Dutartre, Dan; Jezequel, Stéphane; Hemmerlé, Matthieu; Colombeau, Gallian; Comar, Alexis

2017-01-01

The capacity of LiDAR and Unmanned Aerial Vehicles (UAVs) to provide plant height estimates as a high-throughput plant phenotyping trait was explored. An experiment over wheat genotypes conducted under well watered and water stress modalities was conducted. Frequent LiDAR measurements were performed along the growth cycle using a phénomobile unmanned ground vehicle. UAV equipped with a high resolution RGB camera was flying the experiment several times to retrieve the digital surface model from structure from motion techniques. Both techniques provide a 3D dense point cloud from which the plant height can be estimated. Plant height first defined as the z-value for which 99.5% of the points of the dense cloud are below. This provides good consistency with manual measurements of plant height (RMSE = 3.5 cm) while minimizing the variability along each microplot. Results show that LiDAR and structure from motion plant height values are always consistent. However, a slight under-estimation is observed for structure from motion techniques, in relation with the coarser spatial resolution of UAV imagery and the limited penetration capacity of structure from motion as compared to LiDAR. Very high heritability values (H2> 0.90) were found for both techniques when lodging was not present. The dynamics of plant height shows that it carries pertinent information regarding the period and magnitude of the plant stress. Further, the date when the maximum plant height is reached was found to be very heritable (H2> 0.88) and a good proxy of the flowering stage. Finally, the capacity of plant height as a proxy for total above ground biomass and yield is discussed. PMID:29230229

Improved quantification of mountain snowpack properties using observations from Unmanned Air Vehicles (UAVs)

NASA Astrophysics Data System (ADS)

Shea, J. M.; Harder, P.; Pomeroy, J. W.; Kraaijenbrink, P. D. A.

2017-12-01

Mountain snowpacks represent a critical seasonal reservoir of water for downstream needs, and snowmelt is a significant component of mountain hydrological budgets. Ground-based point measurements are unable to describe the full spatial variability of snow accumulation and melt rates, and repeat Unmanned Air Vehicle (UAV) surveys provide an unparalleled opportunity to measure snow accumulation, redistribution and melt in alpine environments. This study presents results from a UAV-based observation campaign conducted at the Fortress Mountain Snow Laboratory in the Canadian Rockies in 2017. Seven survey flights were conducted between April (maximum snow accumulation) and mid-July (bare ground) to collect imagery with both an RGB camera and thermal infrared imager with the sensefly eBee RTK platform. UAV imagery are processed with structure from motion techniques, and orthoimages, digital elevation models, and surface temperature maps are validated against concurrent ground observations of snow depth, snow water equivalent, and snow surface temperature. We examine the seasonal evolution of snow depth and snow surface temperature, and explore the spatial covariances of these variables with respect to topographic factors and snow ablation rates. Our results have direct implications for scaling snow ablation calculations and model resolution and discretization.

Atmospheric Radiation Measurement Program facilities newsletter, January 2000

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sisterson, D.L.

2000-02-16

The subject of this newsletter is the ARM unmanned aerospace vehicle program. The ARM Program's focus is on climate research, specifically research related to solar radiation and its interaction with clouds. The SGP CART site contains highly sophisticated surface instrumentation, but even these instruments cannot gather some crucial climate data from high in the atmosphere. The Department of Energy and the Department of Defense joined together to use a high-tech, high-altitude, long-endurance class of unmanned aircraft known as the unmanned aerospace vehicle (UAV). A UAV is a small, lightweight airplane that is controlled remotely from the ground. A pilot sitsmore » in a ground-based cockpit and flies the aircraft as if he were actually on board. The UAV can also fly completely on its own through the use of preprogrammed computer flight routines. The ARM UAV is fitted with payload instruments developed to make highly accurate measurements of atmospheric flux, radiance, and clouds. Using a UAV is beneficial to climate research in many ways. The UAV puts the instrumentation within the environment being studied and gives scientists direct measurements, in contrast to indirect measurements from satellites orbiting high above Earth. The data collected by UAVs can be used to verify and calibrate measurements and calculated values from satellites, therefore making satellite data more useful and valuable to researchers.« less

The Goodrich 3rd generation DB-110 system: operational on tactical and unmanned aircraft

NASA Astrophysics Data System (ADS)

Iyengar, Mrinal; Lange, Davis

2006-05-01

Goodrich's DB-110 Reconnaissance Airborne Pod for TORnado (RAPTOR) and Data Link Ground Station (DLGS) have been used operationally for several years by the Royal Air Force (RAF). A variant of the RAPTOR DB-110 Sensor System is currently being used by the Japan Maritime Self Defense Force (JMSDF). Recently, the DB-110 system was flown on the Predator B Unmanned Aerial Vehicle (UAV), demonstrating the DB-110 system's utility on unmanned reconnaissance aircraft. The DB-110 is a dual-band EO and IR imaging capability for long, medium, and short standoff ranges, including oblique and over-flight imaging, in a single sensor package. The DB-110 system has also proven performance for real-time high bandwidth data link imagery transmission. Goodrich has leveraged this operational experience in building a 3rd Generation DB-110 system including new Reconnaissance Airborne Pod and Ground System, to be first used by the Polish Air Force. This 3rd Generation system maintains all the capability of the current 2nd Generation DB-110 system and adds several new features. The 3rd Generation system upgrades include an increase in resolution via new focal planes, addition of a third ("super-wide") field of view, and new avionics. This paper summarizes the Goodrich DB-110 3rd Generation System in terms of its basic design and capabilities. Recent demonstration of the DB-110 on the Predator B UAV is overviewed including sample imagery.

Rapid Prototyping-Unmanned Combat Air Vehicle (UCAV)/Sensorcraft

DTIC Science & Technology

2008-01-01

model. RP may prove to be the fastest means to create a bridge between these CFD and experimental ground testing databases . In the past, it took...UCAV X-45A wind tunnel model within the /RB) ment FD results provide a database of global surface and off-body measurements. It is imperative t...extend the knowledge database for a given aircraft configuration beyond the ground test envelope and into the fligh regime. Working in tandem, in an

Unmanned Aerial Systems and Spectroscopy for Remote Sensing Applications in Archaeology

NASA Astrophysics Data System (ADS)

Themistocleous, K.; Agapiou, A.; Cuca, B.; Hadjimitsis, D. G.

2015-04-01

Remote sensing has open up new dimensions in archaeological research. Although there has been significant progress in increasing the resolution of space/aerial sensors and image processing, the detection of the crop (and soil marks) formations, which relate to buried archaeological remains, are difficult to detect since these marks may not be visible in the images if observed over different period or at different spatial/spectral resolution. In order to support the improvement of earth observation remote sensing technologies specifically targeting archaeological research, a better understanding of the crop/soil marks formation needs to be studied in detail. In this paper the contribution of both Unmanned Aerial Systems as well ground spectroradiometers is discussed in a variety of examples applied in the eastern Mediterranean region (Cyprus and Greece) as well in Central Europe (Hungary). In- situ spectroradiometric campaigns can be applied for the removal of atmospheric impact to simultaneous satellite overpass images. In addition, as shown in this paper, the systematic collection of ground truth data prior to the satellite/aerial acquisition can be used to detect the optimum temporal and spectral resolution for the detection of stress vegetation related to buried archaeological remains. Moreover, phenological studies of the crops from the area of interest can be simulated to the potential sensors based on their Relative Response Filters and therefore prepare better the satellite-aerial campaigns. Ground data and the use of Unmanned Aerial Systems (UAS) can provide an increased insight for studying the formation of crop and soil marks. New algorithms such as vegetation indices and linear orthogonal equations for the enhancement of crop marks can be developed based on the specific spectral characteristics of the area. As well, UAS can be used for remote sensing applications in order to document, survey and model cultural heritage and archaeological sites.

Population Census of a Large Common Tern Colony with a Small Unmanned Aircraft

PubMed Central

Chabot, Dominique; Craik, Shawn R.; Bird, David M.

2015-01-01

Small unmanned aircraft systems (UAS) may be useful for conducting high-precision, low-disturbance waterbird surveys, but limited data exist on their effectiveness. We evaluated the capacity of a small UAS to census a large (>6,000 nests) coastal Common tern (Sterna hirundo) colony of which ground surveys are particularly disruptive and time-consuming. We compared aerial photographic tern counts to ground nest counts in 45 plots (5-m radius) throughout the colony at three intervals over a nine-day period in order to identify sources of variation and establish a coefficient to estimate nest numbers from UAS surveys. We also compared a full colony ground count to full counts from two UAS surveys conducted the following day. Finally, we compared colony disturbance levels over the course of UAS flights to matched control periods. Linear regressions between aerial and ground counts in plots had very strong correlations in all three comparison periods (R 2 = 0.972–0.989, P < 0.001) and regression coefficients ranged from 0.928–0.977 terns/nest. Full colony aerial counts were 93.6% and 94.0%, respectively, of the ground count. Varying visibility of terns with ground cover, weather conditions and image quality, and changing nest attendance rates throughout incubation were likely sources of variation in aerial detection rates. Optimally timed UAS surveys of Common tern colonies following our method should yield population estimates in the 93–96% range of ground counts. Although the terns were initially disturbed by the UAS flying overhead, they rapidly habituated to it. Overall, we found no evidence of sustained disturbance to the colony by the UAS. We encourage colonial waterbird researchers and managers to consider taking advantage of this burgeoning technology. PMID:25874997

Potential Technology Transfer to the DoD Unmanned Ground Vehicle Program.

DTIC Science & Technology

1996-10-01

Germany. This process combines x-ray lithography, galvanic casting, and micromolding technology and can be used to produce a variety of sensors and...whether circulation is being obstructed by atherosclerosis . Finally, work is being done at the University of Minnesota on a microrobotic device

Performance Evaluation of a Prototyped Wireless Ground Sensor Network

DTIC Science & Technology

2005-03-01

the network was capable of dynamic adaptation to failure and degradation. 14. SUBJECT TERMS: Wireless Sensor Network , Unmanned Sensor, Unattended...2 H. WIRELESS SENSOR NETWORKS .................................................................... 3...zation, and network traffic. The evaluated scenarios included outdoor, urban and indoor environments. The characteristics of wireless sensor networks , types

Use of Open Architecture Middleware for Autonomous Platforms

NASA Astrophysics Data System (ADS)

Naranjo, Hector; Diez, Sergio; Ferrero, Francisco

2011-08-01

Network Enabled Capabilities (NEC) is the vision for next-generation systems in the defence domain formulated by governments, the European Defence Agency (EDA) and the North Atlantic Treaty Organization (NATO). It involves the federation of military information systems, rather than just a simple interconnection, to provide each user with the "right information, right place, right time - and not too much". It defines openness, standardization and flexibility principles in military systems, likewise applicable in the civilian space applications.This paper provides the conclusions drawn from "Architecture for Embarked Middleware" (EMWARE) study, funded by the European Defence Agency (EDA).The aim of the EMWARE project was to provide the information and understanding to facilitate the adoption of informed decisions regarding the specification and implementation of Open Architecture Middleware in future distributed systems, linking it with the NEC goal.EMWARE project included the definition of four business cases, each devoted to a different field of application (Unmanned Aerial Vehicles, Helicopters, Unmanned Ground Vehicles and the Satellite Ground Segment).

Operational Overview for UAS Integration in the NAS Project Flight Test Series 3

NASA Technical Reports Server (NTRS)

Valkov, Steffi B.; Sternberg, Daniel; Marston, Michael

2017-01-01

The National Aeronautics and Space Administration Unmanned Aircraft Systems Integration in the National Airspace System Project has conducted a series of flight tests intended to support the reduction of barriers that prevent unmanned aircraft from flying without the required waivers from the Federal Aviation Administration. The 2015 Flight Test Series 3, supported two separate test configurations. The first configuration investigated the timing of Detect and Avoid alerting thresholds using a radar equipped unmanned vehicle and multiple live intruders flown at varying encounter geometries. The second configuration included a surrogate unmanned vehicle (flown from a ground control station, with a safety pilot on board) flying a mission in a virtual air traffic control airspace sector using research pilot displays and Detect and Avoid advisories to maintain separation from live and virtual aircraft. The test was conducted over an eight-week span within the R-2508 Special Use Airspace. Over 200 encounters were flown for the first configuration, and although the second configuration was cancelled after three data collection flights, Flight Test 3 proved to be invaluable for the purposes of planning, managing, and execution of this type of integrated flight test.

Vision systems for manned and robotic ground vehicles

NASA Astrophysics Data System (ADS)

Sanders-Reed, John N.; Koon, Phillip L.

2010-04-01

A Distributed Aperture Vision System for ground vehicles is described. An overview of the hardware including sensor pod, processor, video compression, and displays is provided. This includes a discussion of the choice between an integrated sensor pod and individually mounted sensors, open architecture design, and latency issues as well as flat panel versus head mounted displays. This technology is applied to various ground vehicle scenarios, including closed-hatch operations (operator in the vehicle), remote operator tele-operation, and supervised autonomy for multi-vehicle unmanned convoys. In addition, remote vision for automatic perimeter surveillance using autonomous vehicles and automatic detection algorithms is demonstrated.

Airborne Measurement of Insolation Impact on the Atmospheric Surface Boundary Layer

NASA Astrophysics Data System (ADS)

Jacob, Jamey; Chilson, Phil; Houston, Adam; Detweiler, Carrick; Bailey, Sean; Cloud-Map Team

2017-11-01

Atmospheric surface boundary layer measurements of wind and thermodynamic parameters are conducted during variable insolation conditions, including the 2017 eclipse, using an unmanned aircraft system. It is well known that the air temperatures can drop significantly during a total solar eclipse as has been previously observed. In past eclipses, these observations have primarily been made on the ground. We present results from airborne measurements of the near surface boundary layer using a small unmanned aircraft with high temporal resolution wind and thermodynamic observations. Questions that motivate the study include: How does the temperature within the lower atmospheric boundary vary during an eclipse? What impact does the immediate removal of radiative heating on the ground have on the lower ABL? Do local wind patterns change during an eclipse event and if so why? Will there be a manifestation of the nocturnal boundary layer wind maximum? Comparisons are made with the DOE ARM SGP site that experiences a lower but still significant insolation. Supported by the National Science Foundation under Award Number 1539070.

The Evaluation of GPS techniques for UAV-based Photogrammetry in Urban Area

NASA Astrophysics Data System (ADS)

Yeh, M. L.; Chou, Y. T.; Yang, L. S.

2016-06-01

The efficiency and high mobility of Unmanned Aerial Vehicle (UAV) made them essential to aerial photography assisted survey and mapping. Especially for urban land use and land cover, that they often changes, and need UAVs to obtain new terrain data and the new changes of land use. This study aims to collect image data and three dimensional ground control points in Taichung city area with Unmanned Aerial Vehicle (UAV), general camera and Real-Time Kinematic with positioning accuracy down to centimetre. The study area is an ecological park that has a low topography which support the city as a detention basin. A digital surface model was also built with Agisoft PhotoScan, and there will also be a high resolution orthophotos. There will be two conditions for this study, with or without ground control points and both were discussed and compared for the accuracy level of each of the digital surface models. According to check point deviation estimate, the model without ground control points has an average two-dimension error up to 40 centimeter, altitude error within one meter. The GCP-free RTK-airborne approach produces centimeter-level accuracy with excellent to low risk to the UAS operators. As in the case of the model with ground control points, the accuracy of x, y, z coordinates has gone up 54.62%, 49.07%, and 87.74%, and the accuracy of altitude has improved the most.

The use of unmanned aerial vehicle imagery in intertidal monitoring

NASA Astrophysics Data System (ADS)

Konar, Brenda; Iken, Katrin

2018-01-01

Intertidal monitoring projects are often limited in their practicality because traditional methods such as visual surveys or removal of biota are often limited in the spatial extent for which data can be collected. Here, we used imagery from a small unmanned aerial vehicle (sUAV) to test their potential use in rocky intertidal and intertidal seagrass surveys in the northern Gulf of Alaska. Images captured by the sUAV in the high, mid and low intertidal strata on a rocky beach and within a seagrass bed were compared to data derived concurrently from observer visual surveys and to images taken by observers on the ground. Observer visual data always resulted in the highest taxon richness, but when observer data were aggregated to the lower taxonomic resolution obtained by the sUAV images, overall community composition was mostly similar between the two methods. Ground camera images and sUAV images yielded mostly comparable community composition despite the typically higher taxonomic resolution obtained by the ground camera. We conclude that monitoring goals or research questions that can be answered on a relatively coarse taxonomic level can benefit from an sUAV-based approach because it allows much larger spatial coverage within the time constraints of a low tide interval than is possible by observers on the ground. We demonstrated this large-scale applicability by using sUAV images to develop maps that show the distribution patterns and patchiness of seagrass.

Control and Non-Payload Communications (CNPC) Prototype Radio - Generation 2 Flight Test Report

NASA Technical Reports Server (NTRS)

Ishac, Joseph A.; Iannicca, Dennis C.; Shalkhauser, Kurt A.; Kachmar, Brian A.

2014-01-01

NASA Glenn Research Center conducted a series of flight tests for the purpose of evaluating air-to-ground communications links for future unmanned aircraft systems (UAS). The primary objective of the test effort was to evaluate the transition of the aircraft communications from one ground station to the next, and to monitor data flow during the "hand-off" event. To facilitate the testing, ground stations were installed at locations in Cleveland, Ohio and Albany, Ohio that each provides line-of-sight radio communications with an overflying aircraft. This report describes results from the flight tests including flight parameters, received signal strength measurements, data latency times, and performance observations for the air-to-ground channel.

LiDAR and Image Point Cloud Comparison

DTIC Science & Technology

2014-09-01

UAV unmanned aerial vehicle USGS United States Geological Survey UTM Universal Transverse Mercator WGS 84 World Geodetic System 1984 WSI...19  1.  Physics of LiDAR Systems ................................................................20  III.  DATA AND SOFTWARE...ground control point GPS Global Positioning System IMU inertial measurements unit LiDAR light detection and ranging MI mutual information MVS

Unmanned Ground Vehicle Communications Relays: Lessons Learned

DTIC Science & Technology

2014-04-01

technology, specifically an open-source VPN package, OpenVPN . This technology provides a wrapper around the network messages, providing a plug-and-play...performed in OpenVPN :  Set the Maximum Transmission Unit (MTU) to 1600. This is because each VPN endpoint has an MTU of 1500 (the default for Ethernet

DEM time series of an agricultural watershed

NASA Astrophysics Data System (ADS)

Pineux, Nathalie; Lisein, Jonathan; Swerts, Gilles; Degré, Aurore

2014-05-01

In agricultural landscape soil surface evolves notably due to erosion and deposition phenomenon. Even if most of the field data come from plot scale studies, the watershed scale seems to be more appropriate to understand them. Currently, small unmanned aircraft systems and images treatments are improving. In this way, 3D models are built from multiple covering shots. When techniques for large areas would be to expensive for a watershed level study or techniques for small areas would be too time consumer, the unmanned aerial system seems to be a promising solution to quantify the erosion and deposition patterns. The increasing technical improvements in this growth field allow us to obtain a really good quality of data and a very high spatial resolution with a high Z accuracy. In the center of Belgium, we equipped an agricultural watershed of 124 ha. For three years (2011-2013), we have been monitoring weather (including rainfall erosivity using a spectropluviograph), discharge at three different locations, sediment in runoff water, and watershed microtopography through unmanned airborne imagery (Gatewing X100). We also collected all available historical data to try to capture the "long-term" changes in watershed morphology during the last decades: old topography maps, soil historical descriptions, etc. An erosion model (LANDSOIL) is also used to assess the evolution of the relief. Short-term evolution of the surface are now observed through flights done at 200m height. The pictures are taken with a side overlap equal to 80%. To precisely georeference the DEM produced, ground control points are placed on the study site and surveyed using a Leica GPS1200 (accuracy of 1cm for x and y coordinates and 1.5cm for the z coordinate). Flights are done each year in December to have an as bare as possible ground surface. Specific treatments are developed to counteract vegetation effect because it is know as key sources of error in the DEM produced by small unmanned aircraft systems. The poster will present the older and more recent changes of relief in this intensely exploited watershed and notably show how unmanned airborne imagery might be of help in DEM dynamic modelling to support soil conservation research.

48 CFR 252.228-7001 - Ground and flight risk.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Contracting Officer. (5) Flight crew member means the pilot, the co-pilot, and, unless otherwise provided in... includes any pilot or operator of an unmanned aerial vehicle. If required, a defense systems operator may.... (4) For task order and delivery order contracts, the Contractor's share of the loss shall be the...

Construction and Testing of Broadband High Impedance Ground Planes (HIGPS) for Surface Mount Antennas

DTIC Science & Technology

2008-03-01

Conductor PMC: Perfect Magnetic Conductor RF: Radio Frequency RH: Right-handed SNG : Single Negative TACAN: Tactical Air Navigation UAV: Unmanned Aerial...negative ( SNG ) and double-negative (DNG) materials, and their fascinating properties have driven the interest in MTMs (Engheta and Ziolkowski, 2006

Distributed Common Ground System - Army (DCGS-A) Increment 1 Release 2 Follow-on Operational Test and Evaluation (FOT and E) Report

DTIC Science & Technology

2016-01-01

Moving Target Indicator, Unmanned Aircraft System (UAS), Rivet Joint, U-2, and ground signals intelligence (PROPHET). At the BCT, Ranger Regiment and... metadata catalog managed by the DIB management office (outside of the DCGS-A system ). A metadata is a searchable description of data, and users across...challenge for users . The system required reboots about every 20 hours for users who had heavy workloads such as the fire support analysts and data

UGV Interoperability Profile (IOP) - Overarching Profile JAUS Profiling Rules, Version 0

DTIC Science & Technology

2011-12-21

negative values indicate pivot counter clockwise. - Multi- axle steering vehicles are not supported. Acceleration Limit A SetAcceleration limit...obtained from a Global Positioning Sensor (GPS), but may also be a combination of multiple sensor modalities that lead to a global pose referenced

Joint Doctrine for Unmanned Aircraft Systems: The Air Force and the Army Hold the Key to Success

DTIC Science & Technology

2010-05-03

concept, coupled with sensor technologies that provide multiple video streams to multiple ground units, delivers increased capability and capacity to...airborne surveillance” allow one UAS to collect up to ten video transmissions, sending them to ten different users on the ground. Future iterations...of this technology, dubbed Gorgon Stare, will increase to as many as 65 video streams per UAS by 2014. 31 Being able to send multiple views of an

The image acquisition system design of floor grinder

NASA Astrophysics Data System (ADS)

Wang, Yang-jiang; Liu, Wei; Liu, Hui-qin

2018-01-01

Based on linear CCD, high resolution image real-time acquisition system serves as designing a set of image acquisition system for floor grinder through the calculation of optical imaging system. The entire image acquisition system can collect images of ground before and after the work of the floor grinder, and the data is transmitted through the Bluetooth system to the computer and compared to realize real-time monitoring of its working condition. The system provides technical support for the design of unmanned ground grinders.

Unmanned Aircraft Systems (UAS) Integration in the National Airspace System (NAS) Project KDP-C Review

NASA Technical Reports Server (NTRS)

Grindle, Laurie; Sakahara, Robert; Hackenberg, Davis; Johnson, William

2017-01-01

The topics discussed are the UAS-NAS project life-cycle and ARMD thrust flow down, as well as the UAS environments and how we operate in those environments. NASA's Armstrong Flight Research Center at Edwards, CA, is leading a project designed to help integrate unmanned air vehicles into the world around us. The Unmanned Aircraft Systems Integration in the National Airspace System project, or UAS in the NAS, will contribute capabilities designed to reduce technical barriers related to safety and operational challenges associated with enabling routine UAS access to the NAS. The project falls under the Integrated Systems Research Program office managed at NASA Headquarters by the agency's Aeronautics Research Mission Directorate. NASA's four aeronautics research centers - Armstrong, Ames Research Center, Langley Research Center, and Glenn Research Center - are part of the technology development project. With the use and diversity of unmanned aircraft growing rapidly, new uses for these vehicles are constantly being considered. Unmanned aircraft promise new ways of increasing efficiency, reducing costs, enhancing safety and saving lives 460265main_ED10-0132-16_full.jpg Unmanned aircraft systems such as NASA's Global Hawks (above) and Predator B named Ikhana (below), along with numerous other unmanned aircraft systems large and small, are the prime focus of the UAS in the NAS effort to integrate them into the national airspace. Credits: NASA Photos 710580main_ED07-0243-37_full.jpg The UAS in the NAS project envisions performance-based routine access to all segments of the national airspace for all unmanned aircraft system classes, once all safety-related and technical barriers are overcome. The project will provide critical data to such key stakeholders and customers as the Federal Aviation Administration and RTCA Special Committee 203 (formerly the Radio Technical Commission for Aeronautics) by conducting integrated, relevant system-level tests to adequately address safety and operational challenges of national airspace access by unmanned aircraft systems, or UAS. In the process, the project will work with other key stakeholders to define necessary deliverables and products to help enable such access. Within the project, NASA is focusing on five sub-projects. These five focus areas include assurance of safe separation of unmanned aircraft from manned aircraft when flying in the national airspace; safety-critical command and control systems and radio frequencies to enable safe operation of UAS; human factors issues for ground control stations; airworthiness certification standards for UAS avionics and integrated tests and evaluation designed to determine the viability of emerging UAS technology. Five Focus Areas of the UAS Integration in the NAS Project Separation Assurance Provide an assessment of how planned Next Generation Air Transportation System (NextGen) separation assurance systems, with different functional allocations, perform for UAS in mixed operations with manned aircraft Assess the applicability to UAS and the performance of NASA NextGen separation assurance systems in flight tests with realistic latencies and uncertain trajectories Assess functional allocations ranging from today's ground-based, controller-provided aircraft separation to fully autonomous airborne self-separation Communications Develop data and rationale to obtain appropriate frequency spectrum allocations to enable safe and efficient operation of UAS in the NAS Develop and validate candidate secure safety-critical command and control system/subsystem test equipment for UAS that complies with UAS international/national frequency regulations, standards and recommended practices and minimum operational and aviation system performance standards for UAS Perform analysis to support recommendations for integration of safety-critical command and control systems and air traffic control communications to ensure safe and efficient operation of UAS in the NAS Human Systems Integration Develop a research test bed and database to provide data and proof of concept for GCS - ground control station - operations in the NAS Coordinate with standards organizations to develop human-factors guidelines for GCS operation in the NAS Certification Define a UAS classification scheme and approach to determining Federal Aviation Regulation airworthiness requirements applicable to all UAS digital avionics Provide hazard and risk-related data to support development of type design criteria and best development practices Integrated Tests and Evaluation Integrate and test mature concepts from technical elements to demonstrate and test viability Evaluate the performance of technology development in a relevant environment (full-mission, human-in-the-loop simulations and flight tests)

Design tools for complex dynamic security systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Byrne, Raymond Harry; Rigdon, James Brian; Rohrer, Brandon Robinson

2007-01-01

The development of tools for complex dynamic security systems is not a straight forward engineering task but, rather, a scientific task where discovery of new scientific principles and math is necessary. For years, scientists have observed complex behavior but have had difficulty understanding it. Prominent examples include: insect colony organization, the stock market, molecular interactions, fractals, and emergent behavior. Engineering such systems will be an even greater challenge. This report explores four tools for engineered complex dynamic security systems: Partially Observable Markov Decision Process, Percolation Theory, Graph Theory, and Exergy/Entropy Theory. Additionally, enabling hardware technology for next generation security systemsmore » are described: a 100 node wireless sensor network, unmanned ground vehicle and unmanned aerial vehicle.« less

STBC AF relay for unmanned aircraft system

NASA Astrophysics Data System (ADS)

Adachi, Fumiyuki; Miyazaki, Hiroyuki; Endo, Chikara

2015-01-01

If a large scale disaster similar to the Great East Japan Earthquake 2011 happens, some areas may be isolated from the communications network. Recently, unmanned aircraft system (UAS) based wireless relay communication has been attracting much attention since it is able to quickly re-establish the connection between isolated areas and the network. However, the channel between ground station (GS) and unmanned aircraft (UA) is unreliable due to UA's swing motion and as consequence, the relay communication quality degrades. In this paper, we introduce space-time block coded (STBC) amplify-and-forward (AF) relay for UAS based wireless relay communication to improve relay communication quality. A group of UAs forms single frequency network (SFN) to perform STBC-AF cooperative relay. In STBC-AF relay, only conjugate operation, block exchange and amplifying are required at UAs. Therefore, STBC-AF relay improves the relay communication quality while alleviating the complexity problem at UAs. It is shown by computer simulation that STBC-AF relay can achieve better throughput performance than conventional AF relay.

NASA Dryden Flight Research Center: Unmanned Aircraft Operations

NASA Technical Reports Server (NTRS)

Pestana, Mark

2010-01-01

This slide presentation reviews several topics related to operating unmanned aircraft in particular sharing aspects of unmanned aircraft from the perspective of a pilot. There is a section on the Global Hawk project which contains information about the first Global Hawk science mission, (i.e., Global Hawk Pacific (GloPac). Included in this information is GloPac science highlights, a listing of the GloPac Instruments. The second Global Hawk science mission was Genesis and Rapid Intensification Process (GRIP), for the NASA Hurricane Science Research Team. Information includes the instrumentation and the flights that were undertaken during the program. A section on Ikhana is next. This section includes views of the Ground Control Station (GCS), and a discussion of how the piloting of UAS is different from piloting in a manned aircraft. There is also discussion about displays and controls of aircraft. There is also discussion about what makes a pilot. The last section relates the use of Ikhana in the western states fire mission.

Evaluation of Bare Ground on Rangelands using Unmanned Aerial Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert P. Breckenridge; Maxine Dakins

2011-01-01

Attention is currently being given to methods that assess the ecological condition of rangelands throughout the United States. There are a number of different indicators that assess ecological condition of rangelands. Bare Ground is being considered by a number of agencies and resource specialists as a lead indicator that can be evaluated over a broad area. Traditional methods of measuring bare ground rely on field technicians collecting data along a line transect or from a plot. Unmanned aerial vehicles (UAVs) provide an alternative to collecting field data, can monitor a large area in a relative short period of time, andmore » in many cases can enhance safety and time required to collect data. In this study, both fixed wing and helicopter UAVs were used to measure bare ground in a sagebrush steppe ecosystem. The data were collected with digital imagery and read using the image analysis software SamplePoint. The approach was tested over seven different plots and compared against traditional field methods to evaluate accuracy for assessing bare ground. The field plots were located on the Idaho National Laboratory (INL) site west of Idaho Falls, Idaho in locations where there is very little disturbance by humans and the area is grazed only by wildlife. The comparison of fixed-wing and helicopter UAV technology against field estimates shows good agreement for the measurement of bare ground. This study shows that if a high degree of detail and data accuracy is desired, then a helicopter UAV may be a good platform. If the data collection objective is to assess broad-scale landscape level changes, then the collection of imagery with a fixed-wing system is probably more appropriate.« less

FIRRE command and control station (C2)

NASA Astrophysics Data System (ADS)

Laird, R. T.; Kramer, T. A.; Cruickshanks, J. R.; Curd, K. M.; Thomas, K. M.; Moneyhun, J.

2006-05-01

The Family of Integrated Rapid Response Equipment (FIRRE) is an advanced technology demonstration program intended to develop a family of affordable, scalable, modular, and logistically supportable unmanned systems to meet urgent operational force protection needs and requirements worldwide. The near-term goal is to provide the best available unmanned ground systems to the warfighter in Iraq and Afghanistan. The overarching long-term goal is to develop a fully-integrated, layered force protection system of systems for our forward deployed forces that is networked with the future force C4ISR systems architecture. The intent of the FIRRE program is to reduce manpower requirements, enhance force protection capabilities, and reduce casualties through the use of unmanned systems. FIRRE is sponsored by the Office of the Under Secretary of Defense, Acquisitions, Technology and Logistics (OUSD AT&L), and is managed by the Product Manager, Force Protection Systems (PM-FPS). The FIRRE Command and Control (C2) Station supports two operators, hosts the Joint Battlespace Command and Control Software for Manned and Unmanned Assets (JBC2S), and will be able to host Mission Planning and Rehearsal (MPR) software. The C2 Station consists of an M1152 HMMWV fitted with an S-788 TYPE I shelter. The C2 Station employs five 24" LCD monitors for display of JBC2S software [1], MPR software, and live video feeds from unmanned systems. An audio distribution system allows each operator to select between various audio sources including: AN/PRC-117F tactical radio (SINCGARS compatible), audio prompts from JBC2S software, audio from unmanned systems, audio from other operators, and audio from external sources such as an intercom in an adjacent Tactical Operations Center (TOC). A power distribution system provides battery backup for momentary outages. The Ethernet network, audio distribution system, and audio/video feeds are available for use outside the C2 Station.

[Micron]ADS-B Detect and Avoid Flight Tests on Phantom 4 Unmanned Aircraft System

NASA Technical Reports Server (NTRS)

Arteaga, Ricardo; Dandachy, Mike; Truong, Hong; Aruljothi, Arun; Vedantam, Mihir; Epperson, Kraettli; McCartney, Reed

2018-01-01

Researchers at the National Aeronautics and Space Administration Armstrong Flight Research Center in Edwards, California and Vigilant Aerospace Systems collaborated for the flight-test demonstration of an Automatic Dependent Surveillance-Broadcast based collision avoidance technology on a small unmanned aircraft system equipped with the uAvionix Automatic Dependent Surveillance-Broadcast transponder. The purpose of the testing was to demonstrate that National Aeronautics and Space Administration / Vigilant software and algorithms, commercialized as the FlightHorizon UAS"TM", are compatible with uAvionix hardware systems and the DJI Phantom 4 small unmanned aircraft system. The testing and demonstrations were necessary for both parties to further develop and certify the technology in three key areas: flights beyond visual line of sight, collision avoidance, and autonomous operations. The National Aeronautics and Space Administration and Vigilant Aerospace Systems have developed and successfully flight-tested an Automatic Dependent Surveillance-Broadcast Detect and Avoid system on the Phantom 4 small unmanned aircraft system. The Automatic Dependent Surveillance-Broadcast Detect and Avoid system architecture is especially suited for small unmanned aircraft systems because it integrates: 1) miniaturized Automatic Dependent Surveillance-Broadcast hardware; 2) radio data-link communications; 3) software algorithms for real-time Automatic Dependent Surveillance-Broadcast data integration, conflict detection, and alerting; and 4) a synthetic vision display using a fully-integrated National Aeronautics and Space Administration geobrowser for three dimensional graphical representations for ownship and air traffic situational awareness. The flight-test objectives were to evaluate the performance of Automatic Dependent Surveillance-Broadcast Detect and Avoid collision avoidance technology as installed on two small unmanned aircraft systems. In December 2016, four flight tests were conducted at Edwards Air Force Base. Researchers in the ground control station looking at displays were able to verify the Automatic Dependent Surveillance-Broadcast target detection and collision avoidance resolutions.

Spatio-temporal monitoring of cotton cultivation using ground-based and airborne multispectral sensors in GIS environment.

PubMed

Papadopoulos, Antonis; Kalivas, Dionissios; Theocharopoulos, Sid

2017-07-01

Multispectral sensor capability of capturing reflectance data at several spectral channels, together with the inherent reflectance responses of various soils and especially plant surfaces, has gained major interest in crop production. In present study, two multispectral sensing systems, a ground-based and an aerial-based, were applied for the multispatial and temporal monitoring of two cotton fields in central Greece. The ground-based system was Crop Circle ACS-430, while the aerial consisted of a consumer-level quadcopter (Phantom 2) and a modified Hero3+ Black digital camera. The purpose of the research was to monitor crop growth with the two systems and investigate possible interrelations between the derived well-known normalized difference vegetation index (NDVI). Five data collection campaigns were conducted during the cultivation period and concerned scanning soil and plants with the ground-based sensor and taking aerial photographs of the fields with the unmanned aerial system. According to the results, both systems successfully monitored cotton growth stages in terms of space and time. The mean values of NDVI changes through time as retrieved by the ground-based system were satisfactorily modelled by a second-order polynomial equation (R 2 0.96 in Field 1 and 0.99 in Field 2). Further, they were highly correlated (r 0.90 in Field 1 and 0.74 in Field 2) with the according values calculated via the aerial-based system. The unmanned aerial system (UAS) can potentially substitute crop scouting as it concerns a time-effective, non-destructive and reliable way of soil and plant monitoring.

An adaptable, low cost test-bed for unmanned vehicle systems research

NASA Astrophysics Data System (ADS)

Goppert, James M.

2011-12-01

An unmanned vehicle systems test-bed has been developed. The test-bed has been designed to accommodate hardware changes and various vehicle types and algorithms. The creation of this test-bed allows research teams to focus on algorithm development and employ a common well-tested experimental framework. The ArduPilotOne autopilot was developed to provide the necessary level of abstraction for multiple vehicle types. The autopilot was also designed to be highly integrated with the Mavlink protocol for Micro Air Vehicle (MAV) communication. Mavlink is the native protocol for QGroundControl, a MAV ground control program. Features were added to QGroundControl to accommodate outdoor usage. Next, the Mavsim toolbox was developed for Scicoslab to allow hardware-in-the-loop testing, control design and analysis, and estimation algorithm testing and verification. In order to obtain linear models of aircraft dynamics, the JSBSim flight dynamics engine was extended to use a probabilistic Nelder-Mead simplex method. The JSBSim aircraft dynamics were compared with wind-tunnel data collected. Finally, a structured methodology for successive loop closure control design is proposed. This methodology is demonstrated along with the rest of the test-bed tools on a quadrotor, a fixed wing RC plane, and a ground vehicle. Test results for the ground vehicle are presented.

A method for using unmanned aerial vehicles for emergency investigation of single geo-hazards and sample applications of this method

NASA Astrophysics Data System (ADS)

Huang, Haifeng; Long, Jingjing; Yi, Wu; Yi, Qinglin; Zhang, Guodong; Lei, Bangjun

2017-11-01

In recent years, unmanned aerial vehicles (UAVs) have become widely used in emergency investigations of major natural hazards over large areas; however, UAVs are less commonly employed to investigate single geo-hazards. Based on a number of successful investigations in the Three Gorges Reservoir area, China, a complete UAV-based method for performing emergency investigations of single geo-hazards is described. First, a customized UAV system that consists of a multi-rotor UAV subsystem, an aerial photography subsystem, a ground control subsystem and a ground surveillance subsystem is described in detail. The implementation process, which includes four steps, i.e., indoor preparation, site investigation, on-site fast processing and application, and indoor comprehensive processing and application, is then elaborated, and two investigation schemes, automatic and manual, that are used in the site investigation step are put forward. Moreover, some key techniques and methods - e.g., the layout and measurement of ground control points (GCPs), route planning, flight control and image collection, and the Structure from Motion (SfM) photogrammetry processing - are explained. Finally, three applications are given. Experience has shown that using UAVs for emergency investigation of single geo-hazards greatly reduces the time, intensity and risks associated with on-site work and provides valuable, high-accuracy, high-resolution information that supports emergency responses.

Storing and Predicting Dynamic Attributes in a World Model Knowledge Store

DTIC Science & Technology

2007-01-01

1 INTRODUCTION ..................................................................................................................16 Motivation and...be addressed and summarily solved by future robotic engineers. 16 CHAPTER 1 INTRODUCTION The world of mobile, intelligent robotics is...Office of the Secretary of Defense charted what was then the Joint Architecture for Unmanned Ground Vehicles Working Group ( JAUGS WG). JAUGS has since

Innovation Talk at TARDEC by Dr. Tulga Ersal

Science.gov Websites

problems of teleoperation and fully autonomous operation of large Unmanned Ground Vehicles (UGVs) at high wide spectrum in their mode of operation ranging from teleoperated, in which the remote human operator implementable solution. High speeds also present a challenge to fully autonomous operation with respect to

Unmanned Aerial Systems Traffic Management (UTM): Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.; Cavolowsky, John

2015-01-01

Flexibility where possible, and structure where necessary. Consider the needs of national security, safe airspace operations, economic opportunities, and emerging technologies. Risk-based approach based on population density, assets on the ground, density of operations, etc. Digital, virtual, dynamic, and as needed UTM services to manage operations.

Spatio-temporal evaluation of plant height in corn via unmanned aerial systems

NASA Astrophysics Data System (ADS)

Varela, Sebastian; Assefa, Yared; Vara Prasad, P. V.; Peralta, Nahuel R.; Griffin, Terry W.; Sharda, Ajay; Ferguson, Allison; Ciampitti, Ignacio A.

2017-07-01

Detailed spatial and temporal data on plant growth are critical to guide crop management. Conventional methods to determine field plant traits are intensive, time-consuming, expensive, and limited to small areas. The objective of this study was to examine the integration of data collected via unmanned aerial systems (UAS) at critical corn (Zea mays L.) developmental stages for plant height and its relation to plant biomass. The main steps followed in this research were (1) workflow development for an ultrahigh resolution crop surface model (CSM) with the goal of determining plant height (CSM-estimated plant height) using data gathered from the UAS missions; (2) validation of CSM-estimated plant height with ground-truthing plant height (measured plant height); and (3) final estimation of plant biomass via integration of CSM-estimated plant height with ground-truthing stem diameter data. Results indicated a correlation between CSM-estimated plant height and ground-truthing plant height data at two weeks prior to flowering and at flowering stage, but high predictability at the later growth stage. Log-log analysis on the temporal data confirmed that these relationships are stable, presenting equal slopes for both crop stages evaluated. Concluding, data collected from low-altitude and with a low-cost sensor could be useful in estimating plant height.

Orbital operation study. Volume 3: Basic vehicle summaries

NASA Technical Reports Server (NTRS)

Anderson, N. R.; Gianformaggio, A.

1972-01-01

The vehicle related data developed during the orbital operations study are described. The interfacing activity findings have been realigned into the four basic vehicle systems as follows: (1) earth orbital shuttle (EOS), (2) research and applications module (RAM), (3) space based, ground based, manned and unmanned tugs, and (4) modular space station (MSS).

Storing and Predicting Dynamic Attributes in a World Model Knowledge Store

DTIC Science & Technology

2009-05-01

14 CHAPTER 1 INTRODUCTION ... INTRODUCTION The world of mobile, intelligent robotics is expanding rapidly. As the shape, size, function and capabilities of these systems change, so...Ground Vehicles Working Group ( JAUGS WG). JAUGS has since transitioned to encompass the realm of all unmanned systems. It is the goal of the working group

Mission Specification and Control for Unmanned Aerial and Ground Vehicles for Indoor Target Discovery and Tracking

DTIC Science & Technology

2010-01-01

open garage leading to the building interior. The UAV is positioned north of a potential ingress to the building. As the mission begins, the UAV...camera, the difficulty in detecting and navigating around obstacles using this non- stereo camera necessitated a precomputed map of all obstacles and

High throughput phenotyping of tomato spotted wilt disease in peanuts using unmanned aerial systems and multispectral imaging

USDA-ARS?s Scientific Manuscript database

The amount of visible and near infrared light reflected by plants varies depending on their health. In this study, multispectral images were acquired by quadcopter for detecting tomato spot wilt virus amongst twenty genetic varieties of peanuts. The plants were visually assessed to acquire ground ...

Unmanned Aerial Systems Traffic Management (UTM): Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Jung, Jaewoo; Kopardekar, Parimal H.

2016-01-01

Flexibility where possible, and structure where necessary. Consider the needs of national security, safe airspace operations, economic opportunities, and emerging technologies. Risk-based approach based on population density, assets on the ground, density of operations, etc. Digital, virtual, dynamic, and as needed UTM services to manage operations.

The Role of Model Fidelity in Model Predictive Control Based Hazard Avoidance in Unmanned Ground Vehicles Using Lidar Sensors

DTIC Science & Technology

2013-03-08

Mechanical Engineering University of Michigan Ann Arbor, MI 48109 ljch@umich.edu Paramsothy Jayakumar U.S. Army RDECOM-TARDEC Warren, MI 48397...5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Jiechao Liu; Paramsothy Jayakumar ; James Overholt; Jeffrey Stein; Tulga Ersal 5d

Real-Time Risk Assessment Framework for Unmanned Aircraft System (UAS) Traffic Management (UTM)

NASA Technical Reports Server (NTRS)

Ancel, Ersin; Capristan, Francisco M.; Foster, John V.; Condotta, Ryan

2017-01-01

The new Federal Aviation Administration (FAA) Small Unmanned Aircraft rule (Part 107) marks the first national regulations for commercial operation of small unmanned aircraft systems (sUAS) under 55 pounds within the National Airspace System (NAS). Although sUAS flights may not be performed beyond visual line-of-sight or over non- participant structures and people, safety of sUAS operations must still be maintained and tracked at all times. Moreover, future safety-critical operation of sUAS (e.g., for package delivery) are already being conceived and tested. NASA's Unmanned Aircraft System Trac Management (UTM) concept aims to facilitate the safe use of low-altitude airspace for sUAS operations. This paper introduces the UTM Risk Assessment Framework (URAF) which was developed to provide real-time safety evaluation and tracking capability within the UTM concept. The URAF uses Bayesian Belief Networks (BBNs) to propagate off -nominal condition probabilities based on real-time component failure indicators. This information is then used to assess the risk to people on the ground by calculating the potential impact area and the effects of the impact. The visual representation of the expected area of impact and the nominal risk level can assist operators and controllers with dynamic trajectory planning and execution. The URAF was applied to a case study to illustrate the concept.

Aeromagnetic Surveying with a Rotary-Wing Unmanned Aircraft System: A Case Study from a Zinc Deposit in Nash Creek, New Brunswick, Canada

NASA Astrophysics Data System (ADS)

Cunningham, Michael; Samson, Claire; Wood, Alan; Cook, Ian

2017-12-01

Unmanned aircraft systems (UASs) have been under rapid development for applications in the mineral exploration industry, mainly for aeromagnetic surveying. They provide improved detection of smaller, deeper and weaker magnetic targets. A traditional system flying an altitude of 100 m above ground level (AGL) can detect a spherical ore body with a radius of 16 m and a magnetic susceptibility of 10-4 buried at a depth of 40 m. A UAS flying at an altitude of 50 or 2 m AGL would require the radius to be 11 or 5 m, respectively. A demonstration survey was performed using the SkyLance rotary-wing UAS instrumented with a cesium vapour magnetometer in Nash Creek, New Brunswick, Canada. The UAS flew over a zinc deposit featuring three magnetic anomalies. It acquired repeatable data that compared well with upward continuation maps of ground magnetic data. Dykes or faults that are dipping eastward at 25° and are approximately 1.5 m wide fit the observed response of the three anomalies captured on the UAS magnetic data.

Unmanned Aerial Vehicles (UAVs) and Artificial Intelligence Revolutionizing Wildlife Monitoring and Conservation

PubMed Central

Gonzalez, Luis F.; Montes, Glen A.; Puig, Eduard; Johnson, Sandra; Mengersen, Kerrie; Gaston, Kevin J.

2016-01-01

Surveying threatened and invasive species to obtain accurate population estimates is an important but challenging task that requires a considerable investment in time and resources. Estimates using existing ground-based monitoring techniques, such as camera traps and surveys performed on foot, are known to be resource intensive, potentially inaccurate and imprecise, and difficult to validate. Recent developments in unmanned aerial vehicles (UAV), artificial intelligence and miniaturized thermal imaging systems represent a new opportunity for wildlife experts to inexpensively survey relatively large areas. The system presented in this paper includes thermal image acquisition as well as a video processing pipeline to perform object detection, classification and tracking of wildlife in forest or open areas. The system is tested on thermal video data from ground based and test flight footage, and is found to be able to detect all the target wildlife located in the surveyed area. The system is flexible in that the user can readily define the types of objects to classify and the object characteristics that should be considered during classification. PMID:26784196

Deep convolutional neural network for classifying Fusarium wilt of radish from unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Ha, Jin Gwan; Moon, Hyeonjoon; Kwak, Jin Tae; Hassan, Syed Ibrahim; Dang, Minh; Lee, O. New; Park, Han Yong

2017-10-01

Recently, unmanned aerial vehicles (UAVs) have gained much attention. In particular, there is a growing interest in utilizing UAVs for agricultural applications such as crop monitoring and management. We propose a computerized system that is capable of detecting Fusarium wilt of radish with high accuracy. The system adopts computer vision and machine learning techniques, including deep learning, to process the images captured by UAVs at low altitudes and to identify the infected radish. The whole radish field is first segmented into three distinctive regions (radish, bare ground, and mulching film) via a softmax classifier and K-means clustering. Then, the identified radish regions are further classified into healthy radish and Fusarium wilt of radish using a deep convolutional neural network (CNN). In identifying radish, bare ground, and mulching film from a radish field, we achieved an accuracy of ≥97.4%. In detecting Fusarium wilt of radish, the CNN obtained an accuracy of 93.3%. It also outperformed the standard machine learning algorithm, obtaining 82.9% accuracy. Therefore, UAVs equipped with computational techniques are promising tools for improving the quality and efficiency of agriculture today.

Unmanned Aerial Vehicles (UAVs) and Artificial Intelligence Revolutionizing Wildlife Monitoring and Conservation.

PubMed

Gonzalez, Luis F; Montes, Glen A; Puig, Eduard; Johnson, Sandra; Mengersen, Kerrie; Gaston, Kevin J

2016-01-14

Surveying threatened and invasive species to obtain accurate population estimates is an important but challenging task that requires a considerable investment in time and resources. Estimates using existing ground-based monitoring techniques, such as camera traps and surveys performed on foot, are known to be resource intensive, potentially inaccurate and imprecise, and difficult to validate. Recent developments in unmanned aerial vehicles (UAV), artificial intelligence and miniaturized thermal imaging systems represent a new opportunity for wildlife experts to inexpensively survey relatively large areas. The system presented in this paper includes thermal image acquisition as well as a video processing pipeline to perform object detection, classification and tracking of wildlife in forest or open areas. The system is tested on thermal video data from ground based and test flight footage, and is found to be able to detect all the target wildlife located in the surveyed area. The system is flexible in that the user can readily define the types of objects to classify and the object characteristics that should be considered during classification.

First Report of Using Portable Unmanned Aircraft Systems (Drones) for Search and Rescue.

PubMed

Van Tilburg, Christopher

2017-06-01

Unmanned aircraft systems (UAS), colloquially called drones, are used commonly for military, government, and civilian purposes, including both commercial and consumer applications. During a search and rescue mission in Oregon, a UAS was used to confirm a fatality in a slot canyon; this eliminated the need for a dangerous rappel at night by rescue personnel. A second search mission in Oregon used several UAS to clear terrain. This allowed search of areas that were not accessible or were difficult to clear by ground personnel. UAS with cameras may be useful for searching, observing, and documenting missions. It is possible that UAS might be useful for delivering equipment in difficult areas and in communication. Copyright © 2017. Published by Elsevier Inc.

Ikhana: A NASA Unmanned Aerial System Supporting Long-Duration Earth Science Missions

NASA Technical Reports Server (NTRS)

Cobleigh, Brent R.

2007-01-01

This viewgraph presentation reviews Ikhana's project goals: (1) Develop an airborne platform to conduct Earth observation and atmospheric sampling science missions both nationally and internationally, (2) develop and demonstrate technologies that improve the capability of UAVs to conduct science collection missions, (3) develop technologies that improve manned and unmanned aircraft systems, and (4) support important national UAV development activities. The criteria that guided the selection of the aircraft are listed. The payload areas on Ikhana are shown and the network that connects the systems are also reviewed. The data recorder is shown. Also the diagram of the Airborne Research Test System (ARTS) is reviewed. The Mobile Ground Control Station and the Mobile Ku SatCom Antenna are also shown and described.

Small catchments DEM creation using Unmanned Aerial Vehicles

NASA Astrophysics Data System (ADS)

Gafurov, A. M.

2018-01-01

Digital elevation models (DEM) are an important source of information on the terrain, allowing researchers to evaluate various exogenous processes. The higher the accuracy of DEM the better the level of the work possible. An important source of data for the construction of DEMs are point clouds obtained with terrestrial laser scanning (TLS) and unmanned aerial vehicles (UAV). In this paper, we present the results of constructing a DEM on small catchments using UAVs. Estimation of the UAV DEM showed comparable accuracy with the TLS if real time kinematic Global Positioning System (RTK-GPS) ground control points (GCPs) and check points (CPs) were used. In this case, the main source of errors in the construction of DEMs are the errors in the referencing of survey results.

Functional design for operational earth resources ground data processing

NASA Technical Reports Server (NTRS)

Baldwin, C. J. (Principal Investigator); Bradford, L. H.; Hutson, D. E.; Jugle, D. R.

1972-01-01

The author has identified the following significant results. Study emphasis was on developing a unified concept for the required ground system, capable of handling data from all viable acquisition platforms and sensor groupings envisaged as supporting operational earth survey programs. The platforms considered include both manned and unmanned spacecraft in near earth orbit, and continued use of low and high altitude aircraft. The sensor systems include both imaging and nonimaging devices, operated both passively and actively, from the ultraviolet to the microwave regions of the electromagnetic spectrum.

Leveraging Science and Technology to Improve Logistics

DTIC Science & Technology

2012-04-05

to the Banana Wars in the late 1920s, specifically the Nicaraguan campaign in 1927. To transport troops and supplies by air in support of combat...military culture of innovation. As the warfighters changed how they fought, the logisticians had to change how they supported the warfighter. When the US...operated to a high level of autonomy Max payload = 544kg TerraMax [Type: Large Wheeled Logistics UGV] [Status: In Development] A modified

Robotic Intelligence Kernel: Driver

DOE Office of Scientific and Technical Information (OSTI.GOV)

The INL Robotic Intelligence Kernel-Driver is built on top of the RIK-A and implements a dynamic autonomy structure. The RIK-D is used to orchestrate hardware for sensing and action as well as software components for perception, communication, behavior and world modeling into a single cognitive behavior kernel that provides intrinsic intelligence for a wide variety of unmanned ground vehicle systems.

Unmanned Intratheater Airlift

DTIC Science & Technology

2010-12-01

aircraft use a standard forward- thrust turbojet or turbofan engine that provides forward thrust while in forward flight. However, when performing...Afghanistan and Iraq required resupply by ground convoy, airdrop, or verticaltakeoff- and-landing aircraft . Unfortunately, the Department of Defense (DOD...challenges and requirements, the author suggests the use of remotely piloted aircraft (RPA) as a potential solution. Focusing on existing and quickly

Network command processing system overview

NASA Technical Reports Server (NTRS)

Nam, Yon-Woo; Murphy, Lisa D.

1993-01-01

The Network Command Processing System (NCPS) developed for the National Aeronautics and Space Administration (NASA) Ground Network (GN) stations is a spacecraft command system utilizing a MULTIBUS I/68030 microprocessor. This system was developed and implemented at ground stations worldwide to provide a Project Operations Control Center (POCC) with command capability for support of spacecraft operations such as the LANDSAT, Shuttle, Tracking and Data Relay Satellite, and Nimbus-7. The NCPS consolidates multiple modulation schemes for supporting various manned/unmanned orbital platforms. The NCPS interacts with the POCC and a local operator to process configuration requests, generate modulated uplink sequences, and inform users of the ground command link status. This paper presents the system functional description, hardware description, and the software design.

Flight Test Overview for UAS Integration in the NAS Project

NASA Technical Reports Server (NTRS)

Murphy, James R.; Hayes, Peggy S.; Kim, Sam K.; Bridges, Wayne; Marston, Michael

2016-01-01

The National Aeronautics and Space Administration is conducting a series of flight tests intended to support the reduction of barriers that prevent unmanned aircraft from flying without the required waivers from the Federal Aviation Administration. The most recent testing supported two separate test configurations. The first investigated the timing of Detect and Avoid (DAA) alerting thresholds using a radar-equipped unmanned vehicle and multiple live intruders flown at varying encounter geometries. The second configuration included a surrogate unmanned vehicle (flown from a ground control station, with a safety pilot on board) flying a mission in a virtual air traffic control airspace sector using research pilot displays and DAA advisories to maintain separation from live and virtual aircraft. The test was conducted over a seven-week span in the summer of 2015. The data from over 100 encounter sorties will be used to inform the RTCA Phase 1 Detect and Avoid and Command and Control Minimum Operating Performance Standards (MOPS) intended to be completed by the summer of 2016. Follow-on flight-testing is planned for the spring of 2016 to capture remaining encounters and support validation of the MOPS.

Automatic construction of aerial corridor for navigation of unmanned aircraft systems in class G airspace using LiDAR

NASA Astrophysics Data System (ADS)

Feng, Dengchao; Yuan, Xiaohui

2016-05-01

According to the airspace classification by the Federal Aviation Agency, Class G airspace is the airspace at 1,200 feet or less to the ground, which is beneath class E airspace and between classes B-D cylinders around towered airstrips. However, the lack of flight supervision mechanism in this airspace, unmanned aerial system (UAS) missions pose many safety issues. Collision avoidance and route planning for UASs in class G airspace is critical for broad deployment of UASs in commercial and security applications. Yet, unlike road network, there is no stationary marker in airspace to identify corridors that are available and safe for UASs to navigate. In this paper, we present an automatic LiDAR-based airspace corridor construction method for navigation in class G airspace and a method for route planning to minimize collision and intrusion. Our idea is to combine LiDAR to automatically identify ground objects that pose navigation restrictions such as airports and high-rises. Digital terrain model (DTM) is derived from LiDAR point cloud to provide an altitude-based class G airspace description. Following the FAA Aeronautical Information Manual, the ground objects that define the restricted airspaces are used together with digital surface model derived from LiDAR data to construct the aerial corridor for navigation of UASs. Preliminary results demonstrate competitive performance and the construction of aerial corridor can be automated with much great efficiency.

In situ Volcanic Plume Monitoring with small Unmanned Aerial Systems for Cal/Val of Satellite Remote Sensing Data: CARTA-UAV 2013 Mission (Invited)

NASA Astrophysics Data System (ADS)

Diaz, J. A.; Pieri, D. C.; Bland, G.; Fladeland, M. M.

2013-12-01

The development of small unmanned aerial systems (sUAS) with a variety of sensor packages, enables in situ and proximal remote sensing measurements of volcanic plumes. Using Costa Rican volcanoes as a Natural Laboratory, the University of Costa Rica as host institution, in collaboration with four NASA centers, have started an initiative to develop low-cost, field-deployable airborne platforms to perform volcanic gas & ash plume research, and in-situ volcanic monitoring in general, in conjunction with orbital assets and state-of-the-art models of plume transport and composition. Several gas sensors have been deployed into the active plume of Turrialba Volcano including a miniature mass spectrometer, and an electrochemical SO2 sensor system with temperature, pressure, relative humidity, and GPS sensors. Several different airborne platforms such as manned research aircraft, unmanned aerial vehicles, tethered balloons, as well as man-portable in-situ ground truth systems are being used for this research. Remote sensing data is also collected from the ASTER and OMI spaceborne instruments and compared with in situ data. The CARTA-UAV 2013 Mission deployment and follow up measurements successfully demonstrated a path to study and visualize gaseous volcanic emissions using mass spectrometer and gas sensor based instrumentation in harsh environment conditions to correlate in situ ground/airborne data with remote sensing satellite data for calibration and validation purposes. The deployment of such technology improves on our current capabilities to detect, analyze, monitor, model, and predict hazards presented to aircraft by volcanogenic ash clouds from active and impending volcanic eruptions.

The Use of a Satellite Communications System for Command and Control of the National Aeronautics and Space Administration Surrogate Unmanned Aerial System Research Aircraft

NASA Technical Reports Server (NTRS)

Howell, Charles T.; Jones, Frank; Hutchinson, Brian; Joyce, Claude; Nelson, Skip; Melum, Mike

2017-01-01

The NASA Langley Research Center has transformed a Cirrus Design SR22 general aviation (GA) aircraft into an Unmanned Aerial Systems (UAS) Surrogate research aircraft which has served for several years as a platform for unmanned systems research and development. The aircraft is manned with a Safety Pilot and a Research Systems Operator (RSO) that allows for flight operations almost any-where in the national airspace system (NAS) without the need for a Federal Aviation Administration (FAA) Certificate of Authorization (COA). The UAS Surrogate can be remotely controlled from a modular, transportable ground control station (GCS) like a true UAS. Ground control of the aircraft is accomplished by the use of data links that allow the two-way passage of the required data to control the aircraft and provide the GCS with situational awareness. The original UAS Surrogate data-link system was composed of redundant very high frequency (VHF) data radio modems with a maximum range of approximately 40 nautical miles. A new requirement was developed to extend this range beyond visual range (BVR). This new requirement led to the development of a satellite communications system that provided the means to command and control the UAS Surrogate at ranges beyond the limits of the VHF data links. The system makes use of the Globalstar low earth orbit (LEO) satellite communications system. This paper will provide details of the development, implementation, and flight testing of the satellite data communications system on the UAS Surrogate research aircraft.

The first X-45A Unmanned Combat Air Vehicle (UCAV) technology demonstrator completed its sixth flight on Dec. 19, 2002, raising its landing gear in flight for the first time. The X-45A flew for 40 minutes and reached an airspeed of 195 knots

NASA Image and Video Library

2002-12-19

The first X-45A Unmanned Combat Air Vehicle (UCAV) technology demonstrator completed its sixth flight on Dec. 19, 2002, raising its landing gear in flight for the first time. The X-45A flew for 40 minutes and reached an airspeed of 195 knots and an altitude of 7,500 feet. Dryden is supporting the DARPA/Boeing team in the design, development, integration, and demonstration of the critical technologies, processes, and system attributes leading to an operational UCAV system. Dryden support of the X-45A demonstrator system includes analysis, component development, simulations, ground and flight tests.

Tactical Unmanned Ground Vehicle Related Research References (BTA Study)

DTIC Science & Technology

1993-03-01

draw bar pull - 4,297 lbs; Engine - 65 hp air cooled diesel engine ; dual electrical motors, hydrostatic drive; Observation - three closed-circuit...8217 Munitions and Chemical Command. Commander, U. S. Army Chemical Research, Development, and Engineering Center. 40..... "Unmanned Air Vehicles Payloads...8217 Larry Brantley Advanced Systems Concepts Office Research, Development, and Engineering Center MARCH 1993 edetone qArs nal, Alabama 35898-5000

Collaborative Point Paper on Border Surveillance Technology

DTIC Science & Technology

2007-06-01

Systems PLC LORHIS (Long Range Hyperspectral Imaging System ) can be configured for either manned or unmanned aircraft to automatically detect and...Airships, and/or Aerostats, (RF, Electro-Optical, Infrared, Video) • Land- based Sensor Systems (Attended/Mobile and Unattended: e.g., CCD, Motion, Acoustic...electronic surveillance technologies for intrusion detection and warning. These ground- based systems are primarily short-range, up to around 500 meters

Fine-resolution repeat topographic surveying of dryland landscapes using UAS-based structure-from-motion photogrammetry: Assessing accuracy and precision against traditional ground-based erosion measurements

USDA-ARS?s Scientific Manuscript database

Structure-from-motion (SfM) photogrammetry from unmanned aircraft system (UAS) imagery is an emerging tool for repeat topographic surveying of dryland erosion. These methods are particularly appealing due to the ability to cover large landscapes compared to field methods and at reduced costs and hig...

Collaborative Point Paper on Border Surveillance Technology

DTIC Science & Technology

2007-12-01

including; Unmanned Aerial Vehicles, Airships, and/or Aerostats, (RF, Electro-Optical, Infrared, Video) • Land- based Sensor Systems (Attended...warning. These ground- based systems are primarily short-range, up to around 500 meters. • Observation towers extend surveillance capabilities many...Foreign Companies Applicable Environment(s Foreign Companies Air Land Maritime Technology 25. BAE Systems PLC (BAE Systems Inc. is a US subsidiary

Evaluation of the ImmerVision IMV1-1/3NI Panomorph Lens on a Small Unmanned Ground Vehicle (SUGV)

DTIC Science & Technology

2013-07-01

360°. For the above reason, a 1.3-MP Chameleon color universal serial bus (USB) camera with a 1/3-in CCD from PGR was selected instead of...recommended qualified cameras to host the panomorph lens. Having the advantage of a small footprint, the Chameleon camera with the IMV1 lens can be easily

Machine Learning Control For Highly Reconfigurable High-Order Systems

DTIC Science & Technology

2015-01-02

develop and flight test a Reinforcement Learning based approach for autonomous tracking of ground targets using a fixed wing Unmanned...Reinforcement Learning - based algorithms are developed for learning agents’ time dependent dynamics while also learning to control them. Three algorithms...to a wide range of engineering- based problems . Implementation of these solutions, however, is often complicated by the hysteretic, non-linear,

TARDEC Update for TTCP

DTIC Science & Technology

2009-04-01

09 COL Kevin Peterson Principal Deputy Program Manager Joint MRAP Vehicle Program 17 MRAP Variant Overview FP COUGAR CAT I (FPII CAT I) MaxxPro BAE...distribution unlimited 13. SUPPLEMENTARY NOTES Presented at the TTCP LND TP3 Annual Meeting and Task Workshop Manned and Unmanned Ground Vehicle Systems, 23...28 April 2009, Suffield, Alberta, Canada, The original document contains color images. 14. ABSTRACT 15. SUBJECT TERMS 16. SECURITY

R2U2: Monitoring and Diagnosis of Security Threats for Unmanned Aerial Systems

NASA Technical Reports Server (NTRS)

Schumann, Johann; Moosbruger, Patrick; Rozier, Kristin Y.

2015-01-01

We present R2U2, a novel framework for runtime monitoring of security properties and diagnosing of security threats on-board Unmanned Aerial Systems (UAS). R2U2, implemented in FPGA hardware, is a real-time, REALIZABLE, RESPONSIVE, UNOBTRUSIVE Unit for security threat detection. R2U2 is designed to continuously monitor inputs from the GPS and the ground control station, sensor readings, actuator outputs, and flight software status. By simultaneously monitoring and performing statistical reasoning, attack patterns and post-attack discrepancies in the UAS behavior can be detected. R2U2 uses runtime observer pairs for linear and metric temporal logics for property monitoring and Bayesian networks for diagnosis of security threats. We discuss the design and implementation that now enables R2U2 to handle security threats and present simulation results of several attack scenarios on the NASA DragonEye UAS.

Internet Protocol Over Telemetry Testing for Earth Science Capability Demo Summary

NASA Technical Reports Server (NTRS)

Franz, Russ; Pestana, Mark; Bessent, Shedrick; Hang, Richard; Ng, Howard

2006-01-01

The development and flight tests described here focused on utilizing existing pulse code modulation (PCM) telemetry equipment to enable on-vehicle networks of instruments and computers to be a simple extension of the ground station network. This capability is envisioned as a necessary component of a global range that supports test and development of manned and unmanned airborne vehicles.

UAS CNPC Satellite Link Performance - Sharing Spectrum with Terrestrial Systems

NASA Technical Reports Server (NTRS)

Kerczewski, Robert J.; Wilson, Jeffrey D.; Bishop, William D.

2016-01-01

In order to provide for the safe integration of unmanned aircraft systems into the National Airspace System, the control and non-payload communications (CNPC) link connecting the ground-based pilot with the unmanned aircraft must be highly reliable. A specific requirement is that it must operate using aviation safety radiofrequency spectrum. The 2012 World Radiocommunication Conference (WRC-12) provided a potentially suitable allocation for radio line-of-sight (LOS), terrestrial based CNPC link at 5030-5091 MHz. For a beyond radio line-of-sight (BLOS), satellite-based CNPC link, aviation safety spectrum allocations are currently inadequate. Therefore, the 2015 WRC will consider the use of Fixed Satellite Service (FSS) bands to provide BLOS CNPC under Agenda Item 1.5. This agenda item requires studies to be conducted to allow for the consideration of how unmanned aircraft can employ FSS for BLOS CNPC while maintaining existing systems. Since there are terrestrial Fixed Service systems also using the same frequency bands under consideration in Agenda Item 1.5 one of the studies required considered spectrum sharing between earth stations on-board unmanned aircraft and Fixed Service station receivers. Studies carried out by NASA have concluded that such sharing is possible under parameters previously established by the International Telecommunications Union. As the preparation for WRC-15 has progressed, additional study parameters Agenda Item 1.5 have been proposed, and some studies using these parameters have been added. This paper examines the study results for the original parameters as well as results considering some of the more recently proposed parameters to provide insight into the complicated process of resolving WRC-15 Agenda Item 1.5 and achieving a solution for BLOS CNPC for unmanned aircraft.

Use of Unmanned Aircraft Systems in Observations of Glaciers, Ice Sheets, Sea Ice and Snow Fields

NASA Astrophysics Data System (ADS)

Herzfeld Mayer, M. U.

2015-12-01

Unmanned Aircraft Systems (UAS) are being used increasingly in observations of the Earth, especially as such UAS become smaller, lighter and hence less expensive. In this paper, we present examples of observations of snow fields, glaciers and ice sheets and of sea ice in the Arctic that have been collected from UAS. We further examine possibilities for instrument miniaturization, using smaller UAS and smaller sensors for collecting data. The quality and type of data is compared to that of satellite observations, observations from manned aircraft and to measurements made during field experiments on the ground. For example, a small UAS can be sent out to observe a sudden event, such as a natural catastrophe, and provide high-resolution imagery, but a satellite has the advantage of providing the same type of data over much of the Earth's surface and for several years, but the data is generally of lower resolution. Data collected on the ground typically have the best control and quality, but the survey area is usually small. Here we compare micro-topographic measurements made on snow fields the Colorado Rocky Mountains with airborne and satellite data.

Integrated optimization of unmanned aerial vehicle task allocation and path planning under steady wind.

PubMed

Luo, He; Liang, Zhengzheng; Zhu, Moning; Hu, Xiaoxuan; Wang, Guoqiang

2018-01-01

Wind has a significant effect on the control of fixed-wing unmanned aerial vehicles (UAVs), resulting in changes in their ground speed and direction, which has an important influence on the results of integrated optimization of UAV task allocation and path planning. The objective of this integrated optimization problem changes from minimizing flight distance to minimizing flight time. In this study, the Euclidean distance between any two targets is expanded to the Dubins path length, considering the minimum turning radius of fixed-wing UAVs. According to the vector relationship between wind speed, UAV airspeed, and UAV ground speed, a method is proposed to calculate the flight time of UAV between targets. On this basis, a variable-speed Dubins path vehicle routing problem (VS-DP-VRP) model is established with the purpose of minimizing the time required for UAVs to visit all the targets and return to the starting point. By designing a crossover operator and mutation operator, the genetic algorithm is used to solve the model, the results of which show that an effective UAV task allocation and path planning solution under steady wind can be provided.

ROS-based ground stereo vision detection: implementation and experiments.

PubMed

Hu, Tianjiang; Zhao, Boxin; Tang, Dengqing; Zhang, Daibing; Kong, Weiwei; Shen, Lincheng

This article concentrates on open-source implementation on flying object detection in cluttered scenes. It is of significance for ground stereo-aided autonomous landing of unmanned aerial vehicles. The ground stereo vision guidance system is presented with details on system architecture and workflow. The Chan-Vese detection algorithm is further considered and implemented in the robot operating systems (ROS) environment. A data-driven interactive scheme is developed to collect datasets for parameter tuning and performance evaluating. The flying vehicle outdoor experiments capture the stereo sequential images dataset and record the simultaneous data from pan-and-tilt unit, onboard sensors and differential GPS. Experimental results by using the collected dataset validate the effectiveness of the published ROS-based detection algorithm.

Real Time Corner Detection for Miniaturized Electro-Optical Sensors Onboard Small Unmanned Aerial Systems

PubMed Central

Forlenza, Lidia; Carton, Patrick; Accardo, Domenico; Fasano, Giancarmine; Moccia, Antonio

2012-01-01

This paper describes the target detection algorithm for the image processor of a vision-based system that is installed onboard an unmanned helicopter. It has been developed in the framework of a project of the French national aerospace research center Office National d’Etudes et de Recherches Aérospatiales (ONERA) which aims at developing an air-to-ground target tracking mission in an unknown urban environment. In particular, the image processor must detect targets and estimate ground motion in proximity of the detected target position. Concerning the target detection function, the analysis has dealt with realizing a corner detection algorithm and selecting the best choices in terms of edge detection methods, filtering size and type and the more suitable criterion of detection of the points of interest in order to obtain a very fast algorithm which fulfills the computation load requirements. The compared criteria are the Harris-Stephen and the Shi-Tomasi, ones, which are the most widely used in literature among those based on intensity. Experimental results which illustrate the performance of the developed algorithm and demonstrate that the detection time is fully compliant with the requirements of the real-time system are discussed. PMID:22368499

A Two-Echelon Cooperated Routing Problem for a Ground Vehicle and Its Carried Unmanned Aerial Vehicle

PubMed Central

Luo, Zhihao; Liu, Zhong; Shi, Jianmai

2017-01-01

In this paper, a two-echelon cooperated routing problem for the ground vehicle (GV) and its carried unmanned aerial vehicle (UAV) is investigated, where the GV travels on the road network and its UAV travels in areas beyond the road to visit a number of targets unreached by the GV. In contrast to the classical two-echelon routing problem, the UAV has to launch and land on the GV frequently to change or charge its battery while the GV is moving on the road network. A new 0–1 integer programming model is developed to formulate the problem, where the constraints on the spatial and temporal cooperation of GV and UAV routes are included. Two heuristics are proposed to solve the model: the first heuristic (H1) constructs a complete tour for all targets and splits it by GV routes, while the second heuristic (H2) constructs the GV tour and assigns UAV flights to it. Random instances with six different sizes (25–200 targets, 12–80 rendezvous nodes) are used to test the algorithms. Computational results show that H1 performs slightly better than H2, while H2 uses less time and is more stable. PMID:28513552

Integrated optimization of unmanned aerial vehicle task allocation and path planning under steady wind

PubMed Central

Liang, Zhengzheng; Zhu, Moning; Hu, Xiaoxuan; Wang, Guoqiang

2018-01-01

Wind has a significant effect on the control of fixed-wing unmanned aerial vehicles (UAVs), resulting in changes in their ground speed and direction, which has an important influence on the results of integrated optimization of UAV task allocation and path planning. The objective of this integrated optimization problem changes from minimizing flight distance to minimizing flight time. In this study, the Euclidean distance between any two targets is expanded to the Dubins path length, considering the minimum turning radius of fixed-wing UAVs. According to the vector relationship between wind speed, UAV airspeed, and UAV ground speed, a method is proposed to calculate the flight time of UAV between targets. On this basis, a variable-speed Dubins path vehicle routing problem (VS-DP-VRP) model is established with the purpose of minimizing the time required for UAVs to visit all the targets and return to the starting point. By designing a crossover operator and mutation operator, the genetic algorithm is used to solve the model, the results of which show that an effective UAV task allocation and path planning solution under steady wind can be provided. PMID:29561888

Determining position, velocity and acceleration of free-ranging animals with a low-cost unmanned aerial system.

PubMed

Harvey, Richard J; Roskilly, Kyle; Buse, Chris; Evans, Hannah K; Hubel, Tatjana Y; Wilson, Alan M

2016-09-01

Unmanned aerial systems (UASs), frequently referred to as 'drones', have become more common and affordable and are a promising tool for collecting data on free-ranging wild animals. We used a Phantom-2 UAS equipped with a gimbal-mounted camera to estimate position, velocity and acceleration of a subject on the ground moving through a grid of GPS surveyed ground control points (area ∼1200 m(2)). We validated the accuracy of the system against a dual frequency survey grade GPS system attached to the subject. When compared with GPS survey data, the estimations of position, velocity and acceleration had a root mean square error of 0.13 m, 0.11 m s(-1) and 2.31 m s(-2), respectively. The system can be used to collect locomotion and localisation data on multiple free-ranging animals simultaneously. It does not require specialist skills to operate, is easily transported to field locations, and is rapidly and easily deployed. It is therefore a useful addition to the range of methods available for field data collection on free-ranging animal locomotion. © 2016. Published by The Company of Biologists Ltd.

A Two-Echelon Cooperated Routing Problem for a Ground Vehicle and Its Carried Unmanned Aerial Vehicle.

PubMed

Luo, Zhihao; Liu, Zhong; Shi, Jianmai

2017-05-17

In this paper, a two-echelon cooperated routing problem for the ground vehicle (GV) and its carried unmanned aerial vehicle (UAV) is investigated, where the GV travels on the road network and its UAV travels in areas beyond the road to visit a number of targets unreached by the GV. In contrast to the classical two-echelon routing problem, the UAV has to launch and land on the GV frequently to change or charge its battery while the GV is moving on the road network. A new 0-1 integer programming model is developed to formulate the problem, where the constraints on the spatial and temporal cooperation of GV and UAV routes are included. Two heuristics are proposed to solve the model: the first heuristic (H1) constructs a complete tour for all targets and splits it by GV routes, while the second heuristic (H2) constructs the GV tour and assigns UAV flights to it. Random instances with six different sizes (25-200 targets, 12-80 rendezvous nodes) are used to test the algorithms. Computational results show that H1 performs slightly better than H2, while H2 uses less time and is more stable.

Corn and sorghum phenotyping using a fixed-wing UAV-based remote sensing system

NASA Astrophysics Data System (ADS)

Shi, Yeyin; Murray, Seth C.; Rooney, William L.; Valasek, John; Olsenholler, Jeff; Pugh, N. Ace; Henrickson, James; Bowden, Ezekiel; Zhang, Dongyan; Thomasson, J. Alex

2016-05-01

Recent development of unmanned aerial systems has created opportunities in automation of field-based high-throughput phenotyping by lowering flight operational cost and complexity and allowing flexible re-visit time and higher image resolution than satellite or manned airborne remote sensing. In this study, flights were conducted over corn and sorghum breeding trials in College Station, Texas, with a fixed-wing unmanned aerial vehicle (UAV) carrying two multispectral cameras and a high-resolution digital camera. The objectives were to establish the workflow and investigate the ability of UAV-based remote sensing for automating data collection of plant traits to develop genetic and physiological models. Most important among these traits were plant height and number of plants which are currently manually collected with high labor costs. Vegetation indices were calculated for each breeding cultivar from mosaicked and radiometrically calibrated multi-band imagery in order to be correlated with ground-measured plant heights, populations and yield across high genetic-diversity breeding cultivars. Growth curves were profiled with the aerial measured time-series height and vegetation index data. The next step of this study will be to investigate the correlations between aerial measurements and ground truth measured manually in field and from lab tests.

Cotton growth modeling and assessment using unmanned aircraft system visual-band imagery

NASA Astrophysics Data System (ADS)

Chu, Tianxing; Chen, Ruizhi; Landivar, Juan A.; Maeda, Murilo M.; Yang, Chenghai; Starek, Michael J.

2016-07-01

This paper explores the potential of using unmanned aircraft system (UAS)-based visible-band images to assess cotton growth. By applying the structure-from-motion algorithm, the cotton plant height (ph) and canopy cover (cc) information were retrieved from the point cloud-based digital surface models (DSMs) and orthomosaic images. Both UAS-based ph and cc follow a sigmoid growth pattern as confirmed by ground-based studies. By applying an empirical model that converts the cotton ph to cc, the estimated cc shows strong correlation (R2=0.990) with the observed cc. An attempt for modeling cotton yield was carried out using the ph and cc information obtained on June 26, 2015, the date when sigmoid growth curves for both ph and cc tended to decline in slope. In a cross-validation test, the correlation between the ground-measured yield and the estimated equivalent derived from the ph and/or cc was compared. Generally, combining ph and cc, the performance of the yield estimation is most comparable against the observed yield. On the other hand, the observed yield and cc-based estimation produce the second strongest correlation, regardless of the complexity of the models.

Reconnaissance and Autonomy for Small Robots (RASR)

DTIC Science & Technology

2012-06-29

The Reconnaissance and Autonomy for Small Robots (RASR) team developed a system for the coordination of groups of unmanned ground vehicles (UGVs...development of a system that used 1) a relevant deployable platform; 2) a minimum set of relatively inexpensive navigation and LADAR sensors; 3) an...expandable and modular control system with innovative software algorithms to minimize computing footprint; and that minimized 4) required communications

Defense AT&L. Volume 38, Number 5. September-October 2009

DTIC Science & Technology

2009-10-01

and downward spirals of emotion-driven sell-offs. Conceived and managed without great care and foresight , networked sys- tems function to spread bad...the Joint Project Manager for Nuclear, Biological, and Chemical Contamina- tion Avoidance in June 2009. An Unmanned Ground Vehicle Thrust area two... Project Manager for Nuclear, Biological, and Chemical Contamination Avoidance; the Navy Explosive Ordnance Disposal Technical Division; the Future

Intelligence and Electronic Warfare (IEW) System Fact Sheets

DTIC Science & Technology

1994-04-06

unattended ground sensor system that detects, classifies, and determines direction of movement of intruding personnel and vehicles . It uses remotely...fixed and moving target locations, speed and direction of movement, and classification of tracked/wheeled vehicles . The GSM is equipped with standard... Vehicle The Pointer is a Hand-Launched Unmanned Aerial Vehicle (HL-UAV) to be employed by battalion scouts for t"over-the-hillll reconnaissance and

Challenges for Deploying Man-Portable Robots into Hostile Environments

DTIC Science & Technology

2000-11-01

video, JAUGS , MDARS 1. BACKGROUND In modern-day warfare the most likely battlefield is an urban environment, which poses many threats to today’s...teleoperation, reconnaissance, surveillance, digital video, JAUGS , MDARS 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 18...Architecture (MRHA) and the Joint Architecture for Unmanned Ground Systems ( JAUGS ). The hybrid architecture is termed SMART for Small Robotic Technology. It

An Analysis of the Defense Acquisition Strategy for Unmanned Systems

DTIC Science & Technology

2014-03-01

product service code RAA Rapid Acquisition Authority RCS radar cross section REF Rapid Equipping Force RFID radio frequency identification RDT...commercialization of the radio frequency identification (RFID) chip also provides a useful basis for comparison. WWII served as the proving ground for RFID...companies following the September 11 , 2001 attacks. It is important to note that despite advances in GPS technology and long-range communications

Hands-Free, Heads-Up Control System for Unmanned Ground Vehicles

DTIC Science & Technology

2011-08-10

interface evaluation Industry evaluated two commercial-off-the-shelf (COTS) brain computer interfaces from two companies – Neurosky and Emotiv ...useless, resulting in very low command recognition accuracy. In addition, latency issues plagued the system. Figure 6 Emotiv Headset The... Emotiv system, unlike the Neurosky, required great effort to use and calibrate. It requires 16 foam tips to be wet with saline solution and then

Value of Responsive Launch Safety Toolsets

NASA Astrophysics Data System (ADS)

Devoid, Wayne E.

2013-09-01

This paper will discuss the advantages and disadvantages of all-in-one risk assessment toolsets as they are applied to a wide variety of orbital, suborbital, lander, and unmanned vehicles. Toolsets like APT's SafeLab and Horizon, that are designed from the ground up specifically to address ever- changing vehicle and mission parameters, reduce the need for additional software development costs for launch ranges and vehicle manufacturers.

Performance Evaluation of Intelligent Systems at the National Institute of Standards and Technology (NIST)

DTIC Science & Technology

2011-03-01

past few years, including performance evaluation of emergency response robots , sensor systems on unmanned ground vehicles, speech-to-speech translation...emergency response robots ; intelligent systems; mixed palletizing, testing, simulation; robotic vehicle perception systems; search and rescue robots ...ranging from autonomous vehicles to urban search and rescue robots to speech translation and manufacturing systems. The evaluations have occurred in

Advancing Unmanned Aircraft Sensor Collection and Communication Capabilities with Optical Communications

NASA Astrophysics Data System (ADS)

Lukaczyk, T.

2015-12-01

Unmanned aircraft systems (UAS) are now being used for monitoring climate change over both land and seas. Their uses include monitoring of cloud conditions and atmospheric composition of chemicals and aerosols due to pollution, dust storms, fires, volcanic activity and air-sea fluxes. Additional studies of carbon flux are important for various ecosystem studies of both marine and terrestrial environments specifically, and can be related to climate change dynamics. Many measurements are becoming more complex as additional sensors become small enough to operate on more widely available small UAS. These include interferometric radars as well as scanning and fan-beam lidar systems which produce data streams even greater than those of high resolution video. These can be used to precisely map surfaces of the earth, ocean or ice features that are important for a variety of earth system studies. As these additional sensor capabilities are added to UAS the ability to transmit data back to ground or ship monitoring sites is limited by traditional wireless communication protocols. We describe results of tests of optical communication systems that provide significantly greater communication bandwidths for UAS, and discuss both the bandwidth and effective range of these systems, as well as their power and weight requirements both for systems on UAS, as well as those of ground-based receiver stations. We justify our additional use of Delay and Disruption Tolerant Networking (DTN) communication protocols with optical communication methods to ensure security and continuity of command and control operations. Finally, we discuss the implications for receiving, geo-referencing, archiving and displaying data streams from sensors communicated via optical communication to better enable real-time anomaly detection and adaptive sampling capabilities using multiple UAS or other unmanned or manned systems.

The Proposed Use of Unmanned Aerial System Surrogate Research Aircraft for National Airspace System Integration Research

NASA Technical Reports Server (NTRS)

Howell, Charles T., III

2011-01-01

Research is needed to determine what procedures, aircraft sensors and other systems will be required to allow Unmanned Aerial Systems (UAS) to safely operate with manned aircraft in the National Airspace System (NAS). This paper explores the use of Unmanned Aerial System (UAS) Surrogate research aircraft to serve as platforms for UAS systems research, development, and flight testing. These aircraft would be manned with safety pilots and researchers that would allow for flight operations almost anywhere in the NAS without the need for a Federal Aviation Administration (FAA) Certificate of Authorization (COA). With pilot override capability, these UAS Surrogate aircraft would be controlled from ground stations like true UAS s. It would be possible to file and fly these UAS Surrogate aircraft in the NAS with normal traffic and they would be better platforms for real world UAS research and development over existing vehicles flying in restricted ranges or other sterilized airspace. These UAS surrogate aircraft could be outfitted with research systems as required such as computers, state sensors, video recording, data acquisition, data link, telemetry, instrumentation, and Automatic Dependent Surveillance-Broadcast (ADS-B). These surrogate aircraft could also be linked to onboard or ground based simulation facilities to further extend UAS research capabilities. Potential areas for UAS Surrogate research include the development, flight test and evaluation of sensors to aide in the process of air traffic "see-and-avoid". These and other sensors could be evaluated in real-time and compared with onboard human evaluation pilots. This paper examines the feasibility of using UAS Surrogate research aircraft as test platforms for a variety of UAS related research.

An interactive physics-based unmanned ground vehicle simulator leveraging open source gaming technology: progress in the development and application of the virtual autonomous navigation environment (VANE) desktop

NASA Astrophysics Data System (ADS)

Rohde, Mitchell M.; Crawford, Justin; Toschlog, Matthew; Iagnemma, Karl D.; Kewlani, Guarav; Cummins, Christopher L.; Jones, Randolph A.; Horner, David A.

2009-05-01

It is widely recognized that simulation is pivotal to vehicle development, whether manned or unmanned. There are few dedicated choices, however, for those wishing to perform realistic, end-to-end simulations of unmanned ground vehicles (UGVs). The Virtual Autonomous Navigation Environment (VANE), under development by US Army Engineer Research and Development Center (ERDC), provides such capabilities but utilizes a High Performance Computing (HPC) Computational Testbed (CTB) and is not intended for on-line, real-time performance. A product of the VANE HPC research is a real-time desktop simulation application under development by the authors that provides a portal into the HPC environment as well as interaction with wider-scope semi-automated force simulations (e.g. OneSAF). This VANE desktop application, dubbed the Autonomous Navigation Virtual Environment Laboratory (ANVEL), enables analysis and testing of autonomous vehicle dynamics and terrain/obstacle interaction in real-time with the capability to interact within the HPC constructive geo-environmental CTB for high fidelity sensor evaluations. ANVEL leverages rigorous physics-based vehicle and vehicle-terrain interaction models in conjunction with high-quality, multimedia visualization techniques to form an intuitive, accurate engineering tool. The system provides an adaptable and customizable simulation platform that allows developers a controlled, repeatable testbed for advanced simulations. ANVEL leverages several key technologies not common to traditional engineering simulators, including techniques from the commercial video-game industry. These enable ANVEL to run on inexpensive commercial, off-the-shelf (COTS) hardware. In this paper, the authors describe key aspects of ANVEL and its development, as well as several initial applications of the system.

Methods for In-Flight Wing Shape Predictions of Highly Flexible Unmanned Aerial Vehicles: Formulation of Ko Displacement Theory

NASA Technical Reports Server (NTRS)

Ko, William L.; Fleischer, Van Tran

2010-01-01

The Ko displacement theory is formulated for a cantilever tubular wing spar under bending, torsion, and combined bending and torsion loading. The Ko displacement equations are expressed in terms of strains measured at multiple sensing stations equally spaced on the surface of the wing spar. The bending and distortion strain data can then be input to the displacement equations to calculate slopes, deflections, and cross-sectional twist angles of the wing spar at the strain-sensing stations for generating the deformed shapes of flexible aircraft wing spars. The displacement equations have been successfully validated for accuracy by finite-element analysis. The Ko displacement theory that has been formulated could also be applied to calculate the deformed shape of simple and tapered beams, plates, and tapered cantilever wing boxes. The Ko displacement theory and associated strain-sensing system (such as fiber optic sensors) form a powerful tool for in-flight deformation monitoring of flexible wings and tails, such as those often employed on unmanned aerial vehicles. Ultimately, the calculated displacement data can be visually displayed in real time to the ground-based pilot for monitoring the deformed shape of unmanned aerial vehicles during flight.

Director, Operational Test and Evaluation FY 2014 Annual Report

DTIC Science & Technology

2015-01-01

Federal Departments and Agencies. Mitigation measures such as curtailment of wind turbine operations during test periods, identification of alternative...impact of wind turbines on ground-based and airborne radars, and this investment may help mitigate interference of wind turbines with test range...Frequency Active (SURTASS CLFA) Test Plan Tactical Unmanned Aircraft System Tactical Common Data Link (Shadow) FOT&E OTA Test Plan Tempest Wind 2014

An Analysis of the Defense Acquisition Strategy for Unmanned Systems

DTIC Science & Technology

2013-11-20

Product Service Code RAA Rapid Acquisition Authority RCS Radar Cross Section REF Rapid Equipping Force RFID Radio Frequency Identification RDT...the radio frequency identification (RFID) chip also provides a useful basis for comparison. WWII served as the proving ground for RFID technology...enabling miniaturized Free Space Optical Communications systems capable of scaling across data rates, distances, and platforms and integrating with radio

Guidelines and Metrics for Assessing Space System Cost Estimates

DTIC Science & Technology

2008-01-01

analysis time, reuse tooling, models , mechanical ground-support equipment [MGSE]) High mass margin ( simplifying assumptions used to bound solution...engineering environment changes High reuse of architecture, design , tools, code, test scripts, and commercial real- time operating systems Simplified life...Coronal Explorer TWTA traveling wave tube amplifier USAF U.S. Air Force USCM Unmanned Space Vehicle Cost Model USN U.S. Navy UV ultraviolet UVOT UV

Unmanned Ground Vehicles for Integrated Force Protection

DTIC Science & Technology

2004-04-01

employed. 2 Force Protection 18 MAR 02 Security Posts Squad Laptop Fire Tm Ldr Wearable Computers OP/LP Def Fight Psn SRT Sensors USA, USMC, Allied...visual systems. Attaching sensors and response devices on a monorail proved to be much more technically challenging than expected. Film producers and...facilitate experimentation with weapon aiming and firing techniques from the MRHA. grated Marsupial Delivery System was developed to transport smaller

Transition aerodynamics for 20-percent-scale VTOL unmanned aerial vehicle

NASA Technical Reports Server (NTRS)

Kjerstad, Kevin J.; Paulson, John W., Jr.

1993-01-01

An investigation was conducted in the Langley 14- by 22-Foot Subsonic Tunnel to establish a transition data base for an unmanned aerial vehicle utilizing a powered-lift ejector system and to evaluate alterations to the ejector system for improved vehicle performance. The model used in this investigation was a 20-percent-scale, blended-body, arrow-wing configuration with integrated twin rectangular ejectors. The test was conducted from hover through transition conditions with variations in angle of attack, angle of sideslip, free-stream dynamic pressure, nozzle pressure ratio, and model ground height. Force and moment data along with extensive surface pressure data were obtained. A laser velocimeter technique for measuring inlet flow velocities was demonstrated at a single flow condition, and also a low order panel method was successfully used to numerically simulate the ejector inlet flow.

Design and evaluation of a wing with embedded payloads for Small Unmanned Aerial System (SUAS) applications

NASA Astrophysics Data System (ADS)

Pearson, Roger A.

Rapidly advancing technology has developed multiple thin filmed devices capable of expanding the abilities of Small Unmanned Aircraft Systems (SUAS). This research develops a viable solution for integrating thin film solar cells into a currently operational SUAS. A wing was designed and produced that was capable of replacing the existing wing while providing additional functionality with embedded solar arrays. The study investigates the challenges of meeting the original requirements of the original equipment manufacturer wing while adapting it to fully protect and support structurally embedded payloads. In total, seven complete wings were produced and tested. Combinations of functional and simulated payloads were fully integrated into two of these wings. The merits of these designs were quantified and validated through both ground testing and flight testing with the SUAS.

Detection of rice sheath blight using an unmanned aerial system with high-resolution color and multispectral imaging.

PubMed

Zhang, Dongyan; Zhou, Xingen; Zhang, Jian; Lan, Yubin; Xu, Chao; Liang, Dong

2018-01-01

Detection and monitoring are the first essential step for effective management of sheath blight (ShB), a major disease in rice worldwide. Unmanned aerial systems have a high potential of being utilized to improve this detection process since they can reduce the time needed for scouting for the disease at a field scale, and are affordable and user-friendly in operation. In this study, a commercialized quadrotor unmanned aerial vehicle (UAV), equipped with digital and multispectral cameras, was used to capture imagery data of research plots with 67 rice cultivars and elite lines. Collected imagery data were then processed and analyzed to characterize the development of ShB and quantify different levels of the disease in the field. Through color features extraction and color space transformation of images, it was found that the color transformation could qualitatively detect the infected areas of ShB in the field plots. However, it was less effective to detect different levels of the disease. Five vegetation indices were then calculated from the multispectral images, and ground truths of disease severity and GreenSeeker measured NDVI (Normalized Difference Vegetation Index) were collected. The results of relationship analyses indicate that there was a strong correlation between ground-measured NDVIs and image-extracted NDVIs with the R2 of 0.907 and the root mean square error (RMSE) of 0.0854, and a good correlation between image-extracted NDVIs and disease severity with the R2 of 0.627 and the RMSE of 0.0852. Use of image-based NDVIs extracted from multispectral images could quantify different levels of ShB in the field plots with an accuracy of 63%. These results demonstrate that a customer-grade UAV integrated with digital and multispectral cameras can be an effective tool to detect the ShB disease at a field scale.

Increasing the Mobility of Dismounted Marines

DTIC Science & Technology

2009-10-01

actually been the inspiration for military UGV development programs, including the Defense Advanced Research Projects Agency’s (DARPA) Legged Squad Support...or wheel-based; only the BigDog is a leg -based system. This presented BigDog with certain advantages (particularly involving its ability to traverse...1,000 pounds) Website: http://www.dtiweb.net/index.html 50 General Discussion: Ranlo The Ranlo – named after Defense Technologies, Inc.’s ( DTI

Large Unmanned Aircraft System Operations in the National Airspace System - the NASA 2007 Western States Fire Missions

NASA Technical Reports Server (NTRS)

Buoni, Gregory P.; Howell, Kathleen M.

2008-01-01

The National Aeronautics and Space Administration (NASA) Dryden Flight Research Center (DFRC) Ikhana (ee-kah-nah) project executed the 2007 Western States Fire Missions over several of the western United States using an MQ-9 unmanned aircraft system (UAS) in partnership with the NASA Ames Research Center, the United States Forest Service, and the National Interagency Fire Center. The missions were intended to supply infrared imagery of wildfires to firefighters on the ground within 10 minutes of data acquisition. For each of the eight missions, the NASA DFRC notified the Federal Aviation Administration (FAA) of specific flight plans within three or fewer days of the flight. The FAA Certificate of Waiver or Authorization (commonly referred to as a COA ) process was used to obtain access to the United States National Airspace System. Significant time and resources were necessary to develop the COA application, perform mission planning, and define and approve emergency landing sites. Unique aspects of flying unmanned aircraft created challenges to mission operations. Close coordination with FAA headquarters and air traffic control resulted in safe and successful missions that assisted firefighters by providing near-real-time imagery of selected wildfires.

Multispectral Remote Sensing of the Earth and Environment Using KHawk Unmanned Aircraft Systems

NASA Astrophysics Data System (ADS)

Gowravaram, Saket

This thesis focuses on the development and testing of the KHawk multispectral remote sensing system for environmental and agricultural applications. KHawk Unmanned Aircraft System (UAS), a small and low-cost remote sensing platform, is used as the test bed for aerial video acquisition. An efficient image geotagging and photogrammetric procedure for aerial map generation is described, followed by a comprehensive error analysis on the generated maps. The developed procedure is also used for generation of multispectral aerial maps including red, near infrared (NIR) and colored infrared (CIR) maps. A robust Normalized Difference Vegetation index (NDVI) calibration procedure is proposed and validated by ground tests and KHawk flight test. Finally, the generated aerial maps and their corresponding Digital Elevation Models (DEMs) are used for typical application scenarios including prescribed fire monitoring, initial fire line estimation, and tree health monitoring.

Path planning and energy management of solar-powered unmanned ground vehicles

NASA Astrophysics Data System (ADS)

Kaplan, Adam

Many of the applications pertinent to unmanned vehicles, such as environmental research and analysis, communications, and information-surveillance and reconnaissance, benefit from prolonged vehicle operation time. Conventional efforts to increase the operational time of electric-powered unmanned vehicles have traditionally focused on the design of energy-efficient components and the identification of energy efficient search patterns, while little attention has been paid to the vehicle's mission-level path plan and power management. This thesis explores the formulation and generation of integrated motion-plans and power-schedules for solar-panel equipped mobile robots operating under strict energy constraints, which cannot be effectively addressed through conventional motion planning algorithms. Transit problems are considered to design time-optimal paths using both Balkcom-Mason and Pseudo-Dubins curves. Additionally, a more complicated problem to generate mission plans for vehicles which must persistently travel between certain locations, similar to the traveling salesperson problem (TSP), is presented. A comparison between one of the common motion-planning algorithms and experimental results of the prescribed algorithms, made possible by use of a test environment and mobile robot designed and developed specifically for this research, are presented and discussed.

The second X-45A Unmanned Combat Air Vehicle (UCAV) technology demonstrator aircraft during its maiden flight. The flight marks another milestone for the UCAV program, and verified the aircraft's flight control software

NASA Image and Video Library

2002-11-21

The second X-45A Unmanned Combat Air Vehicle (UCAV) technology demonstrator completed its first flight on November 21, 2002, after taking off from a dry lakebed at NASA's Dryden Flight Research Center, Edwards Air Force Base, California. X-45A vehicle two flew for approximately 30 minutes and reached an airspeed of 195 knots and an altitude of 7500 feet. This flight validated the functionality of the UCAV flight software on the second air vehicle. Dryden is supporting the DARPA/Boeing team in the design, development, integration, and demonstration of the critical technologies, processes, and system attributes leading to an operational UCAV system. Dryden support of the X-45A demonstrator system includes analysis, component development, simulations, ground and flight tests.

A Multi-Robot Sense-Act Approach to Lead to a Proper Acting in Environmental Incidents

PubMed Central

Conesa-Muñoz, Jesús; Valente, João; del Cerro, Jaime; Barrientos, Antonio; Ribeiro, Angela

2016-01-01

Many environmental incidents affect large areas, often in rough terrain constrained by natural obstacles, which makes intervention difficult. New technologies, such as unmanned aerial vehicles, may help address this issue due to their suitability to reach and easily cover large areas. Thus, unmanned aerial vehicles may be used to inspect the terrain and make a first assessment of the affected areas; however, nowadays they do not have the capability to act. On the other hand, ground vehicles rely on enough power to perform the intervention but exhibit more mobility constraints. This paper proposes a multi-robot sense-act system, composed of aerial and ground vehicles. This combination allows performing autonomous tasks in large outdoor areas by integrating both types of platforms in a fully automated manner. Aerial units are used to easily obtain relevant data from the environment and ground units use this information to carry out interventions more efficiently. This paper describes the platforms and sensors required by this multi-robot sense-act system as well as proposes a software system to automatically handle the workflow for any generic environmental task. The proposed system has proved to be suitable to reduce the amount of herbicide applied in agricultural treatments. Although herbicides are very polluting, they are massively deployed on complete agricultural fields to remove weeds. Nevertheless, the amount of herbicide required for treatment is radically reduced when it is accurately applied on patches by the proposed multi-robot system. Thus, the aerial units were employed to scout the crop and build an accurate weed distribution map which was subsequently used to plan the task of the ground units. The whole workflow was executed in a fully autonomous way, without human intervention except when required by Spanish law due to safety reasons. PMID:27517934

Scientific Infrastructure To Support Manned And Unmanned Aircraft, Tethered Balloons, And Related Aerial Activities At Doe Arm Facilities On The North Slope Of Alaska

NASA Astrophysics Data System (ADS)

Ivey, M.; Dexheimer, D.; Hardesty, J.; Lucero, D. A.; Helsel, F.

2015-12-01

The U.S. Department of Energy (DOE), through its scientific user facility, the Atmospheric Radiation Measurement (ARM) facilities, provides scientific infrastructure and data to the international Arctic research community via its research sites located on the North Slope of Alaska. DOE has recently invested in improvements to facilities and infrastructure to support operations of unmanned aerial systems for science missions in the Arctic and North Slope of Alaska. A new ground facility, the Third ARM Mobile Facility, was installed at Oliktok Point Alaska in 2013. Tethered instrumented balloons were used to make measurements of clouds in the boundary layer including mixed-phase clouds. A new Special Use Airspace was granted to DOE in 2015 to support science missions in international airspace in the Arctic. Warning Area W-220 is managed by Sandia National Laboratories for DOE Office of Science/BER. W-220 was successfully used for the first time in July 2015 in conjunction with Restricted Area R-2204 and a connecting Altitude Reservation Corridor (ALTRV) to permit unmanned aircraft to operate north of Oliktok Point. Small unmanned aircraft (DataHawks) and tethered balloons were flown at Oliktok during the summer and fall of 2015. This poster will discuss how principal investigators may apply for use of these Special Use Airspaces, acquire data from the Third ARM Mobile Facility, or bring their own instrumentation for deployment at Oliktok Point, Alaska. The printed poster will include the standard DOE funding statement.

Algorithm for covert convoy of a moving target using a group of autonomous robots

NASA Astrophysics Data System (ADS)

Polyakov, Igor; Shvets, Evgeny

2018-04-01

An important application of autonomous robot systems is to substitute human personnel in dangerous environments to reduce their involvement and subsequent risk on human lives. In this paper we solve the problem of covertly convoying a civilian in a dangerous area with a group of unmanned ground vehicles (UGVs) using social potential fields. The novelty of our work lies in the usage of UGVs as compared to the unmanned aerial vehicles typically employed for this task in the approaches described in literature. Additionally, in our paper we assume that the group of UGVs should simultaneously solve the problem of patrolling to detect intruders on the area. We develop a simulation system to test our algorithms, provide numerical results and give recommendations on how to tune the potentials governing robots' behaviour to prioritize between patrolling and convoying tasks.

The Objective Force Soldier/Soldier Team. Volume II - The Science and Technology Challenges

DTIC Science & Technology

2001-11-01

processing for buried mines Chemical sniffing to detect explosives • UGV/Robotic systems to carry sensors into risk areas • Specialized electronic...CLOSE COMBAT OPTIC 1.4 THERMAL WEAPONS SIGHT 4.9 AN/ PAQ -4C AIMING LIGHT 0.6 DAYLIGHT VIDEO SIGHT 0.2 IMPROVED HELMET 3.2 HELMET MOUNTED DISPLAY 1.5 w

Open source IPSEC software in manned and unmanned space missions

NASA Astrophysics Data System (ADS)

Edwards, Jacob

Network security is a major topic of research because cyber attackers pose a threat to national security. Securing ground-space communications for NASA missions is important because attackers could endanger mission success and human lives. This thesis describes how an open source IPsec software package was used to create a secure and reliable channel for ground-space communications. A cost efficient, reproducible hardware testbed was also created to simulate ground-space communications. The testbed enables simulation of low-bandwidth and high latency communications links to experiment how the open source IPsec software reacts to these network constraints. Test cases were built that allowed for validation of the testbed and the open source IPsec software. The test cases also simulate using an IPsec connection from mission control ground routers to points of interest in outer space. Tested open source IPsec software did not meet all the requirements. Software changes were suggested to meet requirements.

Evaluation of Forest Health Conditions using Unmanned Aircraft Systems (UAS)

NASA Astrophysics Data System (ADS)

Hatfield, M. C.; Heutte, T. M.

2016-12-01

US Forest Service Alaska Region Forest Health Protection (FHP) and University of Alaska Fairbanks, Alaska Center for Unmanned Aircraft Systems Integration (ACUASI) are evaluating capability of Unmanned Aerial Systems (UAS) to monitor forest health conditions in Alaska's Interior Region. In July 2016, the team deployed UAS at locations in the Tanana Valley near Fairbanks in order to familiarize FHP staff with capabilities of UAS for evaluating insect and disease damage. While many potential uses of UAS to evaluate and monitor forest health can be envisioned, this project focused on use of a small UAS for rapid assessment of insect and disease damage. Traditional ground-based methods are limited by distance from ground to canopy and inaccessibility of forest stands due to terrain conditions. Observation from fixed-wing aircraft provide a broad overview of conditions but are limited by minimum safe flying altitude (500' AGL) and aircraft speed ( 100 mph). UAS may provide a crucial bridge to fill in gaps between ground and airborne methods, and offer significant cost savings and greater flexibility over helicopter-based observations. Previous uses of UAS for forest health monitoring are limited - this project focuses on optimizing choice of vehicle, sensors, resolution and area scanned from different altitudes, and use of visual spectrum vs NIR image collection. The vehicle selected was the ACUASI Ptarmigan, a small hexacopter (based on DJI S800 airframe and 3DR autopilot) capable of carrying a 1.5 kg payload for 15 min for close-range environmental monitoring missions. Sites were chosen for conditions favorable to UAS operation and presence of forest insect and disease agents including spruce broom rust, aspen leaf miner, birch leaf roller, and willow leafblotch miner. A total of 29 flights were conducted with 9000+ images collected. Mission variables included camera height, UAS speed, and medium- (Sony NEX-7) vs low-resolution (GoPro Hero) cameras. Invaluable knowledge was gained as to limitations and opportunities for field deployment of UAS relative to local conditions of terrain and forest type. Analysis will include image suitability for orthocorrection and production of stand level image mosaic, with further optimization of image collection parameters to detect known insect- and disease-caused disturbance.

A remotely piloted aircraft system in major incident management: concept and pilot, feasibility study.

PubMed

Abrahamsen, Håkon B

2015-06-10

Major incidents are complex, dynamic and bewildering task environments characterised by simultaneous, rapidly changing events, uncertainty and ill-structured problems. Efficient management, communication, decision-making and allocation of scarce medical resources at the chaotic scene of a major incident is challenging and often relies on sparse information and data. Communication and information sharing is primarily voice-to-voice through phone or radio on specified radio frequencies. Visual cues are abundant and difficult to communicate between teams and team members that are not co-located. The aim was to assess the concept and feasibility of using a remotely piloted aircraft (RPA) system to support remote sensing in simulated major incident exercises. We carried out an experimental, pilot feasibility study. A custom-made, remotely controlled, multirotor unmanned aerial vehicle with vertical take-off and landing was equipped with digital colour- and thermal imaging cameras, a laser beam, a mechanical gripper arm and an avalanche transceiver. We collected data in five simulated exercises: 1) mass casualty traffic accident, 2) mountain rescue, 3) avalanche with buried victims, 4) fisherman through thin ice and 5) search for casualties in the dark. The unmanned aerial vehicle was remotely controlled, with high precision, in close proximity to air space obstacles at very low levels without compromising work on the ground. Payload capacity and tolerance to wind and turbulence were limited. Aerial video, shot from different altitudes, and remote aerial avalanche beacon search were streamed wirelessly in real time to a monitor at a ground base. Electromagnetic interference disturbed signal reception in the ground monitor. A small remotely piloted aircraft can be used as an effective tool carrier, although limited by its payload capacity, wind speed and flight endurance. Remote sensing using already existing remotely piloted aircraft technology in pre-hospital environments is feasible and can be used to support situation assessment and information exchange at a major incident scene. Regulations are needed to ensure the safe use of unmanned aerial vehicles in major incidents. Ethical issues are abundant.

Distributed data fusion across multiple hard and soft mobile sensor platforms

NASA Astrophysics Data System (ADS)

Sinsley, Gregory

One of the biggest challenges currently facing the robotics field is sensor data fusion. Unmanned robots carry many sophisticated sensors including visual and infrared cameras, radar, laser range finders, chemical sensors, accelerometers, gyros, and global positioning systems. By effectively fusing the data from these sensors, a robot would be able to form a coherent view of its world that could then be used to facilitate both autonomous and intelligent operation. Another distinct fusion problem is that of fusing data from teammates with data from onboard sensors. If an entire team of vehicles has the same worldview they will be able to cooperate much more effectively. Sharing worldviews is made even more difficult if the teammates have different sensor types. The final fusion challenge the robotics field faces is that of fusing data gathered by robots with data gathered by human teammates (soft sensors). Humans sense the world completely differently from robots, which makes this problem particularly difficult. The advantage of fusing data from humans is that it makes more information available to the entire team, thus helping each agent to make the best possible decisions. This thesis presents a system for fusing data from multiple unmanned aerial vehicles, unmanned ground vehicles, and human observers. The first issue this thesis addresses is that of centralized data fusion. This is a foundational data fusion issue, which has been very well studied. Important issues in centralized fusion include data association, classification, tracking, and robotics problems. Because these problems are so well studied, this thesis does not make any major contributions in this area, but does review it for completeness. The chapter on centralized fusion concludes with an example unmanned aerial vehicle surveillance problem that demonstrates many of the traditional fusion methods. The second problem this thesis addresses is that of distributed data fusion. Distributed data fusion is a younger field than centralized fusion. The main issues in distributed fusion that are addressed are distributed classification and distributed tracking. There are several well established methods for performing distributed fusion that are first reviewed. The chapter on distributed fusion concludes with a multiple unmanned vehicle collaborative test involving an unmanned aerial vehicle and an unmanned ground vehicle. The third issue this thesis addresses is that of soft sensor only data fusion. Soft-only fusion is a newer field than centralized or distributed hard sensor fusion. Because of the novelty of the field, the chapter on soft only fusion contains less background information and instead focuses on some new results in soft sensor data fusion. Specifically, it discusses a novel fuzzy logic based soft sensor data fusion method. This new method is tested using both simulations and field measurements. The biggest issue addressed in this thesis is that of combined hard and soft fusion. Fusion of hard and soft data is the newest area for research in the data fusion community; therefore, some of the largest theoretical contributions in this thesis are in the chapter on combined hard and soft fusion. This chapter presents a novel combined hard and soft data fusion method based on random set theory, which processes random set data using a particle filter. Furthermore, the particle filter is designed to be distributed across multiple robots and portable computers (used by human observers) so that there is no centralized failure point in the system. After laying out a theoretical groundwork for hard and soft sensor data fusion the thesis presents practical applications for hard and soft sensor data fusion in simulation. Through a series of three progressively more difficult simulations, some important hard and soft sensor data fusion capabilities are demonstrated. The first simulation demonstrates fusing data from a single soft sensor and a single hard sensor in order to track a car that could be driving normally or erratically. The second simulation adds the extra complication of classifying the type of target to the simulation. The third simulation uses multiple hard and soft sensors, with a limited field of view, to track a moving target and classify it as a friend, foe, or neutral. The final chapter builds on the work done in previous chapters by performing a field test of the algorithms for hard and soft sensor data fusion. The test utilizes an unmanned aerial vehicle, an unmanned ground vehicle, and a human observer with a laptop. The test is designed to mimic a collaborative human and robot search and rescue problem. This test makes some of the most important practical contributions of the thesis by showing that the algorithms that have been developed for hard and soft sensor data fusion are capable of running in real time on relatively simple hardware.

Complexity, Robustness, and Multistability in Network Systems with Switching Topologies: A Hierarchical Hybrid Control Approach

DTIC Science & Technology

2015-05-22

sensor networks for managing power levels of wireless networks ; air and ground transportation systems for air traffic control and payload transport and... network systems, large-scale systems, adaptive control, discontinuous systems 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 18. NUMBER OF...cover a broad spectrum of ap- plications including cooperative control of unmanned air vehicles, autonomous underwater vehicles, distributed sensor

Ground vehicle control at NIST: From teleoperation to autonomy

NASA Technical Reports Server (NTRS)

Murphy, Karl N.; Juberts, Maris; Legowik, Steven A.; Nashman, Marilyn; Schneiderman, Henry; Scott, Harry A.; Szabo, Sandor

1994-01-01

NIST is applying their Real-time Control System (RCS) methodology for control of ground vehicles for both the U.S. Army Researh Lab, as part of the DOD's Unmanned Ground Vehicles program, and for the Department of Transportation's Intelligent Vehicle/Highway Systems (IVHS) program. The actuated vehicle, a military HMMWV, has motors for steering, brake, throttle, etc. and sensors for the dashboard gauges. For military operations, the vehicle has two modes of operation: a teleoperation mode--where an operator remotely controls the vehicle over an RF communications network; and a semi-autonomous mode called retro-traverse--where the control system uses an inertial navigation system to steer the vehicle along a prerecorded path. For the IVHS work, intelligent vision processing elements replace the human teleoperator to achieve autonomous, visually guided road following.

Intercomparison of Unmanned Aerial Vehicle and Ground-Based Narrow Band Spectrometers Applied to Crop Trait Monitoring in Organic Potato Production.

PubMed

Domingues Franceschini, Marston Héracles; Bartholomeus, Harm; van Apeldoorn, Dirk; Suomalainen, Juha; Kooistra, Lammert

2017-06-18

Vegetation properties can be estimated using optical sensors, acquiring data on board of different platforms. For instance, ground-based and Unmanned Aerial Vehicle (UAV)-borne spectrometers can measure reflectance in narrow spectral bands, while different modelling approaches, like regressions fitted to vegetation indices, can relate spectra with crop traits. Although monitoring frameworks using multiple sensors can be more flexible, they may result in higher inaccuracy due to differences related to the sensors characteristics, which can affect information sampling. Also organic production systems can benefit from continuous monitoring focusing on crop management and stress detection, but few studies have evaluated applications with this objective. In this study, ground-based and UAV spectrometers were compared in the context of organic potato cultivation. Relatively accurate estimates were obtained for leaf chlorophyll (RMSE = 6.07 µg·cm -2 ), leaf area index (RMSE = 0.67 m²·m -2 ), canopy chlorophyll (RMSE = 0.24 g·m -2 ) and ground cover (RMSE = 5.5%) using five UAV-based data acquisitions, from 43 to 99 days after planting. These retrievals are slightly better than those derived from ground-based measurements (RMSE = 7.25 µg·cm -2 , 0.85 m²·m -2 , 0.28 g·m -2 and 6.8%, respectively), for the same period. Excluding observations corresponding to the first acquisition increased retrieval accuracy and made outputs more comparable between sensors, due to relatively low vegetation cover on this date. Intercomparison of vegetation indices indicated that indices based on the contrast between spectral bands in the visible and near-infrared, like OSAVI, MCARI2 and CI g provided, at certain extent, robust outputs that could be transferred between sensors. Information sampling at plot level by both sensing solutions resulted in comparable discriminative potential concerning advanced stages of late blight incidence. These results indicate that optical sensors, and their integration, have great potential for monitoring this specific organic cropping system.

Intercomparison of Unmanned Aerial Vehicle and Ground-Based Narrow Band Spectrometers Applied to Crop Trait Monitoring in Organic Potato Production

PubMed Central

Domingues Franceschini, Marston Héracles; Bartholomeus, Harm; van Apeldoorn, Dirk; Suomalainen, Juha; Kooistra, Lammert

2017-01-01

Vegetation properties can be estimated using optical sensors, acquiring data on board of different platforms. For instance, ground-based and Unmanned Aerial Vehicle (UAV)-borne spectrometers can measure reflectance in narrow spectral bands, while different modelling approaches, like regressions fitted to vegetation indices, can relate spectra with crop traits. Although monitoring frameworks using multiple sensors can be more flexible, they may result in higher inaccuracy due to differences related to the sensors characteristics, which can affect information sampling. Also organic production systems can benefit from continuous monitoring focusing on crop management and stress detection, but few studies have evaluated applications with this objective. In this study, ground-based and UAV spectrometers were compared in the context of organic potato cultivation. Relatively accurate estimates were obtained for leaf chlorophyll (RMSE = 6.07 µg·cm−2), leaf area index (RMSE = 0.67 m2·m−2), canopy chlorophyll (RMSE = 0.24 g·m−2) and ground cover (RMSE = 5.5%) using five UAV-based data acquisitions, from 43 to 99 days after planting. These retrievals are slightly better than those derived from ground-based measurements (RMSE = 7.25 µg·cm−2, 0.85 m2·m−2, 0.28 g·m−2 and 6.8%, respectively), for the same period. Excluding observations corresponding to the first acquisition increased retrieval accuracy and made outputs more comparable between sensors, due to relatively low vegetation cover on this date. Intercomparison of vegetation indices indicated that indices based on the contrast between spectral bands in the visible and near-infrared, like OSAVI, MCARI2 and CIg provided, at certain extent, robust outputs that could be transferred between sensors. Information sampling at plot level by both sensing solutions resulted in comparable discriminative potential concerning advanced stages of late blight incidence. These results indicate that optical sensors, and their integration, have great potential for monitoring this specific organic cropping system. PMID:28629159

An Analysis of U.S. Army Unmanned Ground Vehicle Strategy

DTIC Science & Technology

2012-07-28

submitted in partial fulfillment of the requirements of the Senior Service College Fellowship. The views expressed in this student academic research paper ...THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 28-07-2012 2. REPORT TYPE Civilian Research Paper 3. DATES COVERED (From - To) 4. TITLE AND...AUTHOR(S) COL Glenn Baca, U.S. Army 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S

Mobility Performance Algorithms for Small Unmanned Ground Vehicles

DTIC Science & Technology

2009-05-01

obstacles need to be developed; specifically, models and data for wheeled vehicle skid steering, interior building floor and roof surfaces, and stair ...an 80-lb SUGV; PackBot® at 50 lb, and GatorTM at 2500 lb. Additionally, the FCS projects that 40% of the military fleet may eventually be robotic ...sensor input analysis and decision-making time. Fields (2002a) discusses representing interaction of humans and robots in the OneSAF Testbed Baseline

Counter Tunnel Exploration, Mapping, and Localization with an Unmanned Ground Vehicle

DTIC Science & Technology

2014-05-01

support terrorist activity. Past robotic tunnel exploration efforts have had limited success in aiding law enforcement to explore and map the suspect...cross-border tunnels. These efforts have made use of adapted explosive ordnance disposal (EOD) or pipe inspection robotic systems that are not ideally... Robotics Enterprise (JGRE) to develop a prototype robotic system for counter-tunnel operations, focusing on exploration, mapping, and characterization of

Challenges for Deployment Man-Portable Robots into Hostile Environments

DTIC Science & Technology

2000-11-01

video, JAUGS , MDARS 1. BACKGROUND In modern-day warfare the most likely battlefield is an urban environment, which poses many threats to today’s...Unmanned Ground Systems ( JAUGS ). The hybrid architecture is termed SMART for Small Robotic Technology. It uses the underlying MDARS MRHA message format...and a similar approach to function-oriented operation4. From JAUGS it borrows the concept of functional agents or components that are responsible for

Wargaming the Enemy Unmanned Aircraft System (UAS) Threat

DTIC Science & Technology

2013-01-01

and various current and future short range air defense systems. In addition, the EWF experiments had Army high altitude airship (HAA) with a...component during these experiments dealt with controlling high speed fighters operating at low altitude over the ground commander’s AO. The...JAGIC).18 “”During experimentation with JAGIC, the ACA delegated a volume of airspace, either below a coordinating altitude or within a high density

Wireless Sensor Buoys for Perimeter Security of Military Vessels and Seabases

DTIC Science & Technology

2015-12-01

however, additional sensors utilizing modern technology and a self -forming, as well as self - healing , network could further diminish attacks against...Space SSDF Ship’s Self -Defense Force UAV Unmanned Aerial Vehicle UGS Unattended Ground Sensor USB Universal Serial Bus USMC United States Marine...conditions may delay their reaction resulting in the attacking surface craft entering into a critically close position. The Ship’s Self -Defense

Motion Planning and Task Assignment for Unmanned Aerial Vehicles Cooperating with Unattended Ground Sensors

DTIC Science & Technology

2014-10-24

problem was formalized as the Dubins travelling salesman problem (TSP). In the second phase of the research we have...given constraints on its motion. This problem was formalized as the Dubins travelling salesman problem (TSP). The contributions of the study in the... problem was formalized as the Dubins travelling salesman problem (TSP). The Dubins Travelling Salesperson Problem (DTSP) and its variants [8, 12,

Investigating the Usefulness of Soldier Aids for Autonomous Unmanned Ground Vehicles, Part 2

DTIC Science & Technology

2015-03-01

distribution is unlimited. 13. SUPPLEMENTARY NOTES DCS Corporation, Alexandria, VA 14. ABSTRACT In the past, robot operation has been a high-cognitive...increase performance and reduce perceived workload. The aids were overlays displaying what an autonomous robot perceived in the environment and the...subsequent course of action planned by the robot . Eight active-duty, US Army Soldiers completed 16 scenario missions using an operator interface

The Deep Space Network

NASA Technical Reports Server (NTRS)

1974-01-01

The objectives, functions, and organization, of the Deep Space Network are summarized. Deep Space stations, ground communications, and network operations control capabilities are described. The network is designed for two-way communications with unmanned spacecraft traveling approximately 1600 km from earth to the farthest planets in the solar system. It has provided tracking and data acquisition support for the following projects: Ranger, Surveyor, Mariner, Pioneer, Apollo, Helios, Viking, and the Lunar Orbiter.

Intelligent autonomy for unmanned naval systems

NASA Astrophysics Data System (ADS)

Steinberg, Marc

2006-05-01

This paper provides an overview of the development and demonstration of intelligent autonomy technologies for control of heterogeneous unmanned naval air and sea vehicles and describes some of the current limitations of such technologies. The focus is on modular technologies that support highly automated retasking and fully autonomous dynamic replanning for up to ten heterogeneous unmanned systems based on high-level mission objectives, priorities, constraints, and Rules-of-Engagement. A key aspect of the demonstrations is incorporating frequent naval operator evaluations in order to gain better understanding of the integrated man/machine system and its tactical utility. These evaluations help ensure that the automation can provide information to the user in a meaningful way and that the user has a sufficient level of control and situation awareness to task the system as needed to complete complex mission tasks. Another important aspect of the program is examination of the interactions of higher-level autonomy algorithms with other relevant components that would be needed within the decision-making and control loops. Examples of these are vision and other sensor processing algorithms, sensor fusion, obstacle avoidance, and other lower level vehicle autonomous navigation, guidance, and control functions. Initial experiments have been completed using medium and high-fidelity vehicle simulations in a virtual warfare environment and inexpensive surrogate vehicles in flight and in-water demonstrations. Simulation experiments included integration of multi-vehicle task allocation, dynamic replanning under constraints, lower level autonomous vehicle control, automatic assessment of the impact of contingencies on plans, management of situation awareness data, operator alert management, and a mixed-initiative operator interface. In-water demonstrations of a maritime situation awareness capability were completed in both a river and a harbor environment using unmanned surface vehicles and a buoy as surrogate platforms. In addition, a multiple heterogeneous vehicle demonstration was performed using five different types of small unmanned air and ground vehicles. This provided some initial experimentation with specifying tasking for high-level mission objectives and then mapping those objectives onto heterogeneous unmanned vehicles that each have different lower-level autonomy software. Finally, this paper will discuss lessons learned.

Human-Robot Interaction Literature Review

DTIC Science & Technology

2012-03-01

coordination, operation of non-simulated UVs, and mixed UAV and UGV systems . Recommendations THRIL should focus on studies that look at operating non...Security, 2012). UAVs were continued to be developed in operations such as Desert Storm, where the Pioneer UAV system provided intelligence and fire... systems . One of the programs that was part of the initial fielding of UGVs in military operations was the Vehicle Teleoperation Capability (VTC). The

Mount Pinatubo, Philippine Islands as seen from STS-59

NASA Image and Video Library

1994-04-10

STS059-L14-170 (9-20 April 1994) --- Orient with the sea at the left. Then Subic Bay is at the lower left corner, and Clark Air Force Base (abandoned after the eruption) is to the lower right of the volcano. A turquoise lake occupies the caldera just below the center of the photograph. Mount Pinatubo erupted in June, 1991 after several hundred years of quiescence. Eruptive activity has nearly ceased, but every torrential rain in this monsoonal climate causes renewed mud flows of a viscous slurry composed of volcanic ash and pumice. Shuttle crews have been photographing the mountain at every opportunity, to add documentation to unmanned-satellite, aerial, and ground-based observations of changes. SRL scientists will use the excellent radar imagery obtained during STS-59 to help discriminate among different kinds of volcanic material, and to extend their observations to other volcanoes around the world using future, perhaps unmanned, radar satellites. Linhof photograph.

Development and Implementation of a Hardware In-the-Loop Test Bed for Unmanned Aerial Vehicle Control Algorithms

NASA Technical Reports Server (NTRS)

Nyangweso, Emmanuel; Bole, Brian

2014-01-01

Successful prediction and management of battery life using prognostic algorithms through ground and flight tests is important for performance evaluation of electrical systems. This paper details the design of test beds suitable for replicating loading profiles that would be encountered in deployed electrical systems. The test bed data will be used to develop and validate prognostic algorithms for predicting battery discharge time and battery failure time. Online battery prognostic algorithms will enable health management strategies. The platform used for algorithm demonstration is the EDGE 540T electric unmanned aerial vehicle (UAV). The fully designed test beds developed and detailed in this paper can be used to conduct battery life tests by controlling current and recording voltage and temperature to develop a model that makes a prediction of end-of-charge and end-of-life of the system based on rapid state of health (SOH) assessment.

Fast Sparse Coding for Range Data Denoising with Sparse Ridges Constraint.

PubMed

Gao, Zhi; Lao, Mingjie; Sang, Yongsheng; Wen, Fei; Ramesh, Bharath; Zhai, Ruifang

2018-05-06

Light detection and ranging (LiDAR) sensors have been widely deployed on intelligent systems such as unmanned ground vehicles (UGVs) and unmanned aerial vehicles (UAVs) to perform localization, obstacle detection, and navigation tasks. Thus, research into range data processing with competitive performance in terms of both accuracy and efficiency has attracted increasing attention. Sparse coding has revolutionized signal processing and led to state-of-the-art performance in a variety of applications. However, dictionary learning, which plays the central role in sparse coding techniques, is computationally demanding, resulting in its limited applicability in real-time systems. In this study, we propose sparse coding algorithms with a fixed pre-learned ridge dictionary to realize range data denoising via leveraging the regularity of laser range measurements in man-made environments. Experiments on both synthesized data and real data demonstrate that our method obtains accuracy comparable to that of sophisticated sparse coding methods, but with much higher computational efficiency.

Line following using a two camera guidance system for a mobile robot

NASA Astrophysics Data System (ADS)

Samu, Tayib; Kelkar, Nikhal; Perdue, David; Ruthemeyer, Michael A.; Matthews, Bradley O.; Hall, Ernest L.

1996-10-01

Automated unmanned guided vehicles have many potential applications in manufacturing, medicine, space and defense. A mobile robot has been designed for the 1996 Automated Unmanned Vehicle Society competition which was held in Orlando, Florida on July 15, 1996. The competition required the vehicle to follow solid and dashed lines around an approximately 800 ft. path while avoiding obstacles, overcoming terrain changes such as inclines and sand traps, and attempting to maximize speed. The purpose of this paper is to describe the algorithm developed for the line following. The line following algorithm images two windows and locates their centroid and with the knowledge that the points are on the ground plane, a mathematical and geometrical relationship between the image coordinates of the points and their corresponding ground coordinates are established. The angle of the line and minimum distance from the robot centroid are then calculated and used in the steering control. Two cameras are mounted on the robot with a camera on each side. One camera guides the robot and when it loses track of the line on its side, the robot control system automatically switches to the other camera. The test bed system has provided an educational experience for all involved and permits understanding and extending the state of the art in autonomous vehicle design.

Unmanned Aerial Survey of Fallen Trees in a Deciduous Broadleaved Forest in Eastern Japan

PubMed Central

Inoue, Tomoharu; Nagai, Shin; Yamashita, Satoshi; Fadaei, Hadi; Ishii, Reiichiro; Okabe, Kimiko; Taki, Hisatomo; Honda, Yoshiaki; Kajiwara, Koji; Suzuki, Rikie

2014-01-01

Since fallen trees are a key factor in biodiversity and biogeochemical cycling, information about their spatial distribution is of use in determining species distribution and nutrient and carbon cycling in forest ecosystems. Ground-based surveys are both time consuming and labour intensive. Remote-sensing technology can reduce these costs. Here, we used high-spatial-resolution aerial photographs (0.5–1.0 cm per pixel) taken from an unmanned aerial vehicle (UAV) to survey fallen trees in a deciduous broadleaved forest in eastern Japan. In nine sub-plots we found a total of 44 fallen trees by ground survey. From the aerial photographs, we identified 80% to 90% of fallen trees that were >30 cm in diameter or >10 m in length, but missed many that were narrower or shorter. This failure may be due to the similarity of fallen trees to trunks and branches of standing trees or masking by standing trees. Views of the same point from different angles may improve the detection rate because they would provide more opportunity to detect fallen trees hidden by standing trees. Our results suggest that UAV surveys will make it possible to monitor the spatial and temporal variations in forest structure and function at lower cost. PMID:25279817

An accurate and adaptable photogrammetric approach for estimating the mass and body condition of pinnipeds using an unmanned aerial system.

PubMed

Krause, Douglas J; Hinke, Jefferson T; Perryman, Wayne L; Goebel, Michael E; LeRoi, Donald J

2017-01-01

Measurements of body size and mass are fundamental to pinniped population management and research. Manual measurements tend to be accurate but are invasive and logistically challenging to obtain. Ground-based photogrammetric techniques are less invasive, but inherent limitations make them impractical for many field applications. The recent proliferation of unmanned aerial systems (UAS) in wildlife monitoring has provided a promising new platform for the photogrammetry of free-ranging pinnipeds. Leopard seals (Hydrurga leptonyx) are an apex predator in coastal Antarctica whose body condition could be a valuable indicator of ecosystem health. We aerially surveyed leopard seals of known body size and mass to test the precision and accuracy of photogrammetry from a small UAS. Flights were conducted in January and February of 2013 and 2014 and 50 photogrammetric samples were obtained from 15 unrestrained seals. UAS-derived measurements of standard length were accurate to within 2.01 ± 1.06%, and paired comparisons with ground measurements were statistically indistinguishable. An allometric linear mixed effects model predicted leopard seal mass within 19.40 kg (4.4% error for a 440 kg seal). Photogrammetric measurements from a single, vertical image obtained using UAS provide a noninvasive approach for estimating the mass and body condition of pinnipeds that may be widely applicable.

The effect of flight altitude to data quality of fixed-wing UAV imagery: case study in Murcia, Spain

NASA Astrophysics Data System (ADS)

Anders, Niels; Keesstra, Saskia; Cammeraat, Erik

2014-05-01

Unmanned Aerial System (UAS) are becoming popular tools in the geosciences due to improving technology and processing techniques. They can potentially fill the gap between spaceborne or manned aircraft remote sensing and terrestrial remote sensing, both in terms of spatial and temporal resolution. In this study we tested a fixed-wing Unmanned Aerial System (UAS) for the application of digital landscape analysis. The focus was to analyze the effect of flight altitude and the effect to accuracy and detail of the produced digital elevation models, derived terrain properties and orthophotos. The aircraft was equipped with a Panasonic GX1 16MP pocket camera with 20 mm lens to capture normal JPEG RGB images. Images were processed using Agisoft Photoscan Pro which includes the structure-from-motion and multiview stereopsis algorithms. The test area consisted of small abandoned agricultural fields in semi-arid Murcia in southeastern Spain. The area was severely damaged after a destructive rainfall event, including damaged check dams, rills, deep gully incisions and piping. Results suggest that careful decisions on flight altitude are essential to find a balance between the area coverage, ground sampling distance, UAS ground speed, camera processing speed and the accurate registration of specific soil erosion features of interest.

Bringing UAVs to the fight: recent army autonomy research and a vision for the future

NASA Astrophysics Data System (ADS)

Moorthy, Jay; Higgins, Raymond; Arthur, Keith

2008-04-01

The Unmanned Autonomous Collaborative Operations (UACO) program was initiated in recognition of the high operational burden associated with utilizing unmanned systems by both mounted and dismounted, ground and airborne warfighters. The program was previously introduced at the 62nd Annual Forum of the American Helicopter Society in May of 20061. This paper presents the three technical approaches taken and results obtained in UACO. All three approaches were validated extensively in contractor simulations, two were validated in government simulation, one was flight tested outside the UACO program, and one was flight tested in Part 2 of UACO. Results and recommendations are discussed regarding diverse areas such as user training and human-machine interface, workload distribution, UAV flight safety, data link bandwidth, user interface constructs, adaptive algorithms, air vehicle system integration, and target recognition. Finally, a vision for UAV As A Wingman is presented.

The exploration of outer space with cameras: A history of the NASA unmanned spacecraft missions

NASA Astrophysics Data System (ADS)

Mirabito, M. M.

The use of television cameras and other video imaging devices to explore the solar system's planetary bodies with unmanned spacecraft is chronicled. Attention is given to the missions and the imaging devices, beginning with the Ranger 7 moon mission, which featured the first successfully operated electrooptical subsystem, six television cameras with vidicon image sensors. NASA established a network of parabolic, ground-based antennas on the earth (the Deep Space Network) to receive signals from spacecraft travelling farther than 16,000 km into space. The image processing and enhancement techniques used to convert spacecraft data transmissions into black and white and color photographs are described, together with the technological requirements that drove the development of the various systems. Terrestrial applications of the planetary imaging systems are explored, including medical and educational uses. Finally, the implementation and functional characteristics of CCDs are detailed, noting their installation on the Space Telescope.

Airship platform for high-resolution space technology telescope

NASA Astrophysics Data System (ADS)

Miller, John A.

1995-06-01

This paper sets out to describe the utilization of an unmanned lighter-than-air vehicle as a sub- orbital airborne mission platform for the deployment of space technology telescopes allowing innovative space quality astronomy to be conducted. The paper describes how a low cost airship of relatively simple design can be produced that will be capable of operating in an unmanned remotely piloted mode from a base, fly to a pressure altitude, shut down engines, and operate in a free balloon stage for the period of experimental research. It will be shown that ballooning will allow the platform to be completely free from vibration, and in conjunction with high altitude and polar weather conditions minimize perturbation caused by weather. This paper outlines the technical features of the airship, the projected mission interfaces and the modus operandi of Airship delivery, ground base and missions operations, and final recovery.

Dynamo: A Model Transition Framework for Dynamic Stability Control and Body Mass Manipulation

DTIC Science & Technology

2011-11-01

driving at high speed, and you turn the steering wheel hard to the right and slam on the brakes, then you will end up in the oversteer regime. At the...sensors (GPS, IMU, LIDAR ) for vehicle control. Figure 17: Dynamo high-speed small UGV hardware platform We will perform experiments to measure the MTC

Determination of the vertical profile of particle number concentration adjacent to a motorway using an unmanned aerial vehicle.

PubMed

Villa, T F; Jayaratne, E R; Gonzalez, L F; Morawska, L

2017-11-01

A quantitative assessment of the vertical profile of traffic pollution, specifically particle number concentration (PNC), in an open space adjacent to a motorway was possible for the first time, to the knowledge of the authors, using an Unmanned Aerial Vehicle (UAV) system. Until now, traffic pollution has only been measured at ground level while the vertical distribution, is limited to studies conducted from buildings or fixed towers and balloons. This new UAV system demonstrated that the PNC sampled during the period form 10 a.m. to 4 p.m., outside the rush hours with a constant traffic flow, increased from a concentration of 2 × 10 4 p/cm 3 near the ground up to 10 m, and then sharply decreased attaining a steady value of 4 × 10 3 p/cm 3 beyond a height of about 40 m. While more comprehensive investigations would be warranted under different conditions, such as topography and vehicle and fuel type, this finding is of great significance, given that it demonstrates the impact of traffic emissions on human exposure, but less so to pollution within the upper part of the boundary layer. Copyright © 2017 Elsevier Ltd. All rights reserved.

Unmanned aerial survey of fallen trees in a deciduous broadleaved forest in eastern Japan.

PubMed

Inoue, Tomoharu; Nagai, Shin; Yamashita, Satoshi; Fadaei, Hadi; Ishii, Reiichiro; Okabe, Kimiko; Taki, Hisatomo; Honda, Yoshiaki; Kajiwara, Koji; Suzuki, Rikie

2014-01-01

Since fallen trees are a key factor in biodiversity and biogeochemical cycling, information about their spatial distribution is of use in determining species distribution and nutrient and carbon cycling in forest ecosystems. Ground-based surveys are both time consuming and labour intensive. Remote-sensing technology can reduce these costs. Here, we used high-spatial-resolution aerial photographs (0.5-1.0 cm per pixel) taken from an unmanned aerial vehicle (UAV) to survey fallen trees in a deciduous broadleaved forest in eastern Japan. In nine sub-plots we found a total of 44 fallen trees by ground survey. From the aerial photographs, we identified 80% to 90% of fallen trees that were >30 cm in diameter or >10 m in length, but missed many that were narrower or shorter. This failure may be due to the similarity of fallen trees to trunks and branches of standing trees or masking by standing trees. Views of the same point from different angles may improve the detection rate because they would provide more opportunity to detect fallen trees hidden by standing trees. Our results suggest that UAV surveys will make it possible to monitor the spatial and temporal variations in forest structure and function at lower cost.

An accurate and adaptable photogrammetric approach for estimating the mass and body condition of pinnipeds using an unmanned aerial system

PubMed Central

Hinke, Jefferson T.; Perryman, Wayne L.; Goebel, Michael E.; LeRoi, Donald J.

2017-01-01

Measurements of body size and mass are fundamental to pinniped population management and research. Manual measurements tend to be accurate but are invasive and logistically challenging to obtain. Ground-based photogrammetric techniques are less invasive, but inherent limitations make them impractical for many field applications. The recent proliferation of unmanned aerial systems (UAS) in wildlife monitoring has provided a promising new platform for the photogrammetry of free-ranging pinnipeds. Leopard seals (Hydrurga leptonyx) are an apex predator in coastal Antarctica whose body condition could be a valuable indicator of ecosystem health. We aerially surveyed leopard seals of known body size and mass to test the precision and accuracy of photogrammetry from a small UAS. Flights were conducted in January and February of 2013 and 2014 and 50 photogrammetric samples were obtained from 15 unrestrained seals. UAS-derived measurements of standard length were accurate to within 2.01 ± 1.06%, and paired comparisons with ground measurements were statistically indistinguishable. An allometric linear mixed effects model predicted leopard seal mass within 19.40 kg (4.4% error for a 440 kg seal). Photogrammetric measurements from a single, vertical image obtained using UAS provide a noninvasive approach for estimating the mass and body condition of pinnipeds that may be widely applicable. PMID:29186134

Proposed tethered unmanned aerial system for the detection of pollution entering the Chesapeake Bay area

NASA Astrophysics Data System (ADS)

Goodman, J.; McKay, J.; Evans, W.; Gadsden, S. Andrew

2016-05-01

This paper is based on a proposed unmanned aerial system platform that is to be outfitted with high-resolution sensors. The proposed system is to be tethered to a moveable ground station, which may be a research vessel or some form of ground vehicle (e.g., car, truck, or rover). The sensors include, at a minimum: camera, infrared sensor, thermal, normalized difference vegetation index (NDVI) camera, global positioning system (GPS), and a light-based radar (LIDAR). The purpose of this paper is to provide an overview of existing methods for pollution detection of failing septic systems, and to introduce the proposed system. Future work will look at the high-resolution data from the sensors and integrating the data through a process called information fusion. Typically, this process is done using the popular and well-published Kalman filter (or its nonlinear formulations, such as the extended Kalman filter). However, future work will look at using a new type of strategy based on variable structure estimation for the information fusion portion of the data processing. It is hypothesized that fusing data from the thermal and NDVI sensors will be more accurate and reliable for a multitude of applications, including the detection of pollution entering the Chesapeake Bay area.

Trace Gas Quantification with Small Unmanned Aerial Systems

NASA Astrophysics Data System (ADS)

Schuyler, T. J.; Guzman, M. I.; Bailey, S.; Jacob, J.

2017-12-01

Measurements of atmospheric composition are generally performed with advanced instrumentation from ground stations using tall towers and weather balloons or with manned aircraft. Unmanned aerial systems (UAS) are a promising technology for atmospheric monitoring of trace atmospheric gases as they can bridge the gap between the regions of the atmospheric boundary layer measured by ground stations and aircraft. However, in general, the sophisticated instrumentation required for these measurements are heavy, preventing its deployment with small UAS. In order to successfully detect and quantify these gases, sensor packages aboard UAS must be lightweight, have low-power consumption, and possess limits of detection on the ppm scale or below with reasonably fast response times. Thus, a new generation of portable instrument is being developed in this work to meet these requirements employing new sensing packages. The cross sensitivity of these sensors to several gases is examined through laboratory testing of the instrument under variable environmental conditions prior to performing field measurements. Datasets include timestamps with position, temperature, relative humidity, pressure, along with variable mixing ratio values of important greenhouse gases. The work will present an analysis of the results gathered during authorized flights performed during the second CLOUD-MAP§ field campaign held in June 2017. §CLOUD-MAP: Collaboration Leading Operational UAS Development for Meteorology and Atmospheric Physics, a 4-year NSF funded effort.

Guidance and control for unmanned ground vehicles

NASA Astrophysics Data System (ADS)

Bateman, Peter J.

1994-06-01

Techniques for the guidance, control, and navigation of unmanned ground vehicles are described in terms of the communication bandwidth requirements for driving and control of a vehicle remote from the human operator. Modes of operation are conveniently classified as conventional teleoperation, supervisory control, and fully autonomous control. The fundamental problem of maintaining a robust non-line-of-sight communications link between the human controller and the remote vehicle is discussed, as this provides the impetus for greater autonomy in the control system and the greatest scope for innovation. While supervisory control still requires the man to be providing the primary navigational intelligence, fully autonomous operation requires that mission navigation is provided solely by on-board machine intelligence. Methods directed at achieving this performance are described using various active and passive sensing of the terrain for route navigation and obstacle detection. Emphasis is given to TV imagery and signal processing techniques for image understanding. Reference is made to the limitations of current microprocessor technology and suitable computer architectures. Some of the more recent control techniques involve the use of neural networks, fuzzy logic, and data fusion and these are discussed in the context of road following and cross country navigation. Examples of autonomous vehicle testbeds operated at various laboratories around the world are given.

Lightweight mid-infrared methane sensor for unmanned aerial systems

NASA Astrophysics Data System (ADS)

Golston, Levi M.; Tao, Lei; Brosy, Caroline; Schäfer, Klaus; Wolf, Benjamin; McSpiritt, James; Buchholz, Bernhard; Caulton, Dana R.; Pan, Da; Zondlo, Mark A.; Yoel, David; Kunstmann, Harald; McGregor, Marty

2017-06-01

The design and field performance of a compact diode laser-based instrument for measuring methane on unmanned aerial systems (UAS) is described. The system is based on open-path, wavelength modulation spectroscopy with a 3.27 µm GaSb laser. We design two versions of the sensor for a long-endurance fixed wing UAS and a rotary wing hexacopter, with instrument masses of 4.6 and 1.6 kg, respectively. The long-endurance platform was used to measure vertical profiles of methane up to 600 m in altitude and showed repeatability of 13 ppbv between multiple profiles. Additionally, the hexacopter system was used to evaluate the evolution of methane in the nocturnal boundary layer during the ScaleX field campaign in Germany, where measured data is consistent with supporting ground-based methane and meteorological measurements. Testing results on both platforms demonstrated our lightweight methane sensor had an in-flight precision of 5-10 ppbv Hz-1/2.

Internationalization of the Space Station

NASA Technical Reports Server (NTRS)

Lottmann, R. V.

1985-01-01

Attention is given to the NASA Space Station system elements whose production is under consideration by potential foreign partners. The ESA's Columbus Program declaration encompasses studies of pressurized modules, unmanned payload carriers, and ground support facilities. Canada has expressed interest in construction and servicing facilities, solar arrays, and remote sensing facilities. Japanese studies concern a multipurpose experimental module concept. Each of these foreign investments would expand Space Station capabilities and lay the groundwork for long term partnerships.

Spread Spectrum Applications in Unmanned Aerial Vehicles

DTIC Science & Technology

1994-06-01

Specter can be launched from the ground or F/A-18 and F-16 aircraft. The Specter carries the Advanced Tactical Air Reconnaissance System ( ATARS ...the transition should be easy. While ATARS is Specter’s designated payload, it can carry other payloads weighing up to 400 pounds: electronic...implement a 650 km UAV. The combination of ATARS digital imagery and a real-time data link, together with the Specter’s ability to fly low, fast, navigate

Development and Demonstration of Autonomous Behaviors for Urban Environment Exploration

DTIC Science & Technology

2012-04-01

exploration, mapping, localization, autonomy, lidar , SLAM 1. INTRODUCTION As global conflicts move into more urban settings, unmanned ground vehicles...mounted Hokuyo lidar is paired with a vertically mounted Hokuyo lidar as an inexpensive way for 3D perception of the environment. In addition, a pair...and mapping ( SLAM ) problem do exist,2–4 most have yet to tackle the problem of online SLAM throughout a multi-story building and/or incorporating

The UAV: A unique platform for electrodynamic studies of upward lightning in the middle atmosphere

NASA Technical Reports Server (NTRS)

Goldberg, Richard A.; Desch, Michael D.; Farrell, William M.

1997-01-01

The use of unmanned aerial vehicles (UAVs), a platform for investigations in an environment hostile to manned spacecraft, is discussed. A program which includes the use of UAVs coupled with ground-based measurements to conduct scientific studies on the electrical state of the atmosphere during electrically active periods is proposed. The radiating power from alternate current and transient components of the storm electrification was investigated.

Agent Transparency for an Autonomous Squad Member

DTIC Science & Technology

2015-05-01

C. Attentional  Control  Survey  41  Appendix D. System Usability Scale  45  Appendix E. Modified Jian Pre‐Post Trust Survey  47  Appendix F.  Posttest ...failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE...information in a simulation-based unmanned ground vehicle monitoring task. Three groups were tested with visual displays representing 1 of 3 types of

A case study of comparing radiometrically calibrated reflectance of an image mosaic from unmanned aerial system with that of a single image from manned aircraft over a same area

NASA Astrophysics Data System (ADS)

Shi, Yeyin; Thomasson, J. Alex; Yang, Chenghai; Cope, Dale; Sima, Chao

2017-05-01

Though sharing with many commonalities, one of the major differences between conventional high-altitude airborne remote sensing and low-altitude unmanned aerial system (UAS) based remote sensing is that the latter one has much smaller ground footprint for each image shot. To cover the same area on the ground, it requires the low-altitude UASbased platform to take many highly-overlapped images to produce a good mosaic, instead of just one or a few image shots by the high-altitude aerial platform. Such an UAS flight usually takes 10 to 30 minutes or even longer to complete; environmental lighting change during this time span cannot be ignored especially when spectral variations of various parts of a field are of interests. In this case study, we compared the visible reflectance of two aerial imagery - one generated from mosaicked UAS images, the other generated from a single image taken by a manned aircraft - over the same agricultural field to quantitatively evaluate their spectral variations caused by the different data acquisition strategies. Specifically, we (1) developed our customized ground calibration points (GCPs) and an associated radiometric calibration method for UAS data processing based on camera's sensitivity characteristics; (2) developed a basic comparison method for radiometrically calibrated data from the two aerial platforms based on regions of interests. We see this study as a starting point for a series of following studies to understand the environmental influence on UAS data and investigate the solutions to minimize such influence to ensure data quality.

Anomaly Detection for Data Reduction in an Unattended Ground Sensor (UGS) Field

DTIC Science & Technology

2014-09-01

information (shown with solid lines in the diagram). Typically, this would be a mobile ad - hoc network (MANET). The clusters are connected to other nodes...interquartile ranges MANET mobile ad - hoc network OSUS Open Standards for Unattended Sensors TOC tactical operations center UAVs unmanned aerial vehicles...19b. TELEPHONE NUMBER (Include area code ) 301-394-1221 Standard Form 298 (Rev. 8/98) Prescribed by ANSI Std. Z39.18 iii Contents List of

Design, Construction and Testing of a Prototype Holonomic Autonomous Vehicle

DTIC Science & Technology

2007-12-01

Circuit A simple 100 kHz crystal oscillator tank circuit using an LM741 opamp was fed to a LM393N comparator . The circuit’s schematic is provided...research in areas that support development of unmanned ground and air battlefield vehicles. Little attention has been paid to applying robotics to...motion control using a single board computer, a pulse width modulation (PWM) and optical isolation circuit, and a low-cost inertial measurement unit

Collaborative Autonomous Unmanned Aerial - Ground Vehicle Systems for Field Operations

DTIC Science & Technology

2007-08-31

very limited payload capabilities of small UVs, sacrificing minimal computational power and run time, adhering at the same time to the low cost...configuration has been chosen because of its high computational capabilities, low power consumption, multiple I/O ports, size, low heat emission and cost. This...due to their high power to weight ratio, small packaging, and wide operating temperatures. Power distribution is controlled by the 120 Watt ATX power

Localization Framework for Real-Time UAV Autonomous Landing: An On-Ground Deployed Visual Approach.

PubMed

Kong, Weiwei; Hu, Tianjiang; Zhang, Daibing; Shen, Lincheng; Zhang, Jianwei

2017-06-19

[-5]One of the greatest challenges for fixed-wing unmanned aircraft vehicles (UAVs) is safe landing. Hereafter, an on-ground deployed visual approach is developed in this paper. This approach is definitely suitable for landing within the global navigation satellite system (GNSS)-denied environments. As for applications, the deployed guidance system makes full use of the ground computing resource and feedbacks the aircraft's real-time localization to its on-board autopilot. Under such circumstances, a separate long baseline stereo architecture is proposed to possess an extendable baseline and wide-angle field of view (FOV) against the traditional fixed baseline schemes. Furthermore, accuracy evaluation of the new type of architecture is conducted by theoretical modeling and computational analysis. Dataset-driven experimental results demonstrate the feasibility and effectiveness of the developed approach.

Localization Framework for Real-Time UAV Autonomous Landing: An On-Ground Deployed Visual Approach

PubMed Central

Kong, Weiwei; Hu, Tianjiang; Zhang, Daibing; Shen, Lincheng; Zhang, Jianwei

2017-01-01

One of the greatest challenges for fixed-wing unmanned aircraft vehicles (UAVs) is safe landing. Hereafter, an on-ground deployed visual approach is developed in this paper. This approach is definitely suitable for landing within the global navigation satellite system (GNSS)-denied environments. As for applications, the deployed guidance system makes full use of the ground computing resource and feedbacks the aircraft’s real-time localization to its on-board autopilot. Under such circumstances, a separate long baseline stereo architecture is proposed to possess an extendable baseline and wide-angle field of view (FOV) against the traditional fixed baseline schemes. Furthermore, accuracy evaluation of the new type of architecture is conducted by theoretical modeling and computational analysis. Dataset-driven experimental results demonstrate the feasibility and effectiveness of the developed approach. PMID:28629189

Ground control station software design for micro aerial vehicles

NASA Astrophysics Data System (ADS)

Walendziuk, Wojciech; Oldziej, Daniel; Binczyk, Dawid Przemyslaw; Slowik, Maciej

2017-08-01

This article describes the process of designing the equipment part and the software of a ground control station used for configuring and operating micro unmanned aerial vehicles (UAV). All the works were conducted on a quadrocopter model being a commonly accessible commercial construction. This article contains a characteristics of the research object, the basics of operating the micro aerial vehicles (MAV) and presents components of the ground control station model. It also describes the communication standards for the purpose of building a model of the station. Further part of the work concerns the software of the product - the GIMSO application (Generally Interactive Station for Mobile Objects), which enables the user to manage the actions and communication and control processes from the UAV. The process of creating the software and the field tests of a station model are also presented in the article.

Black Swift Technologies LLC

NASA Technical Reports Server (NTRS)

DiNardo, Anne Marie

2016-01-01

Colorado-based Black Swift Technologies (BST) created a small unmanned aircraft system(sUAS) to help NASA get a clearer picture of soil moisture through the Small Business Innovation Research (SBIR) program. Soil moisture is defined in terms of volume of water per unit volume of soil. Using BSTs sUAS, NASA scientists can gather ground truth measurements for a clearer observation by getting closer to the source. This can help rule out misleading results generated by satellite imagery.

Wireless Authentication Protocol Implementation: Descriptions of a Zero-Knowledge Proof (ZKP) Protocol Implementation for Testing on Ground and Airborne Mobile Networks

DTIC Science & Technology

2015-01-01

on AFRL’s small unmanned aerial vehicle (UAV) test bed . 15. SUBJECT TERMS Zero-Knowledge Proof Protocol Testing 16. SECURITY CLASSIFICATION OF...VERIFIER*** edition Version Information: Version 1.1.3 Version Details: Successful ZK authentication between two networked machines. Fixed a bug ...that causes intermittent bignum errors. Fixed a network hang bug and now allows continually authentication at the Verifier. Also now removing

Unmanned spacecraft for surveying earth's resources

NASA Technical Reports Server (NTRS)

George, T. A.

1970-01-01

The technical objectives and payloads for ERTS A and B are discussed. The primary emphasis is on coverage of the United States and the ocean areas immediately adjacent, using 3-camera return beam vidicon TV system, 4-channel multispectral point scanner, data collection system, and wideband video tape recorder. The expected performance and system characteristics of the RBV system and the 4-band multispectral object plane point scanner are outlined. Ground station considerations are also given.

Design and Control of Omnidirectional Unmanned Ground Vehicles for Rough Terrain

DTIC Science & Technology

2012-08-29

company, Quantum Signal. This rigid body dynamics simulation, housed within the Autonomous Navigation and Virtual Environment Laboratory (ANVEL) software...72 Figure 22: PIC main code. Page 24 of 72 Figure 23: PIC interrupt code. 3.3 Central Body Embedded Electronics As described above...located on the main body of the vehicle. This section describes how the on-board electronics works. The outline of the code is presented as is how

Using Unmanned Helicopters to Assess Vegetation Cover in Sagebrush Steppe Ecosystems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert P. Breckenridge; Maxine Dakins; Stephen Bunting

2012-07-01

Evaluating vegetation cover is an important factor in understanding the sustainability of many ecosystems. Methods that have sufficient accuracy and improved cost efficiency could dramatically alter how biotic resources are monitored on both public and private lands. This will be of interest to land managers because there are rarely enough resource specialists or funds available for comprehensive ground evaluations. In this project, unmanned helicopters were used to collect still-frame imagery to assess vegetation cover during May, June, and July in 2005. The images were used to estimate percent cover for six vegetative cover classes (shrub, dead shrub, grass, forbs, litter,more » and bare ground). The field plots were located on the INL site west of Idaho Falls, Idaho. Ocular assessments of digital imagery were performed using a software program called SamplePoint, and the results were compared against field measurements collected using a point-frame method to assess accuracy. The helicopter imagery evaluation showed a high degree of agreement with field cover class values for litter, bare ground, and grass, and reasonable agreement for dead shrubs. Shrub cover was often overestimated and forbs were generally underestimated. The helicopter method took 45% less time than the field method to set plots and collect and analyze data. This study demonstrates that UAV technology provides a viable method for monitoring vegetative cover on rangelands in less time and with lower costs. Tradeoffs between cost and accuracy are critical management decisions that are important when managing vegetative conditions across vast sagebrush ecosystems throughout the Intermountain West.« less

Assessing the impacts of canopy openness and flight parameters on detecting a sub-canopy tropical invasive plant using a small unmanned aerial system

NASA Astrophysics Data System (ADS)

Perroy, Ryan L.; Sullivan, Timo; Stephenson, Nathan

2017-03-01

Small unmanned aerial systems (sUAS) have great potential to facilitate the early detection and management of invasive plants. Here we show how very high-resolution optical imagery, collected from small consumer-grade multirotor UAS platform at altitudes of 30-120 m above ground level (agl), can be used to detect individual miconia (Miconia calvescens) plants in a highly invaded tropical rainforest environment on the island of Hawai'i. The central aim of this research was to determine how overstory vegetation cover, imagery resolution, and camera look-angle impact the aerial detection of known individual miconia plants. For our finest resolution imagery (1.37 cm ground sampling distance collected at 30 m agl), we obtained a 100% detection rate for sub-canopy plants with above-crown openness values >40% and a 69% detection rate for those with >20% openness. We were unable to detect any plants with <10% above crown openness. Detection rates progressively declined with coarser spatial resolution imagery, ending in a 0% detection rate for the 120 m agl flights (ground sampling distance of 5.31 cm). The addition of forward-looking oblique imagery improved detection rates for plants below overstory vegetation, though this effect decreased with increasing flight altitude. While dense overstory canopy cover, limited flight times, and visual line of sight regulations present formidable obstacles for detecting miconia and other invasive plant species, we show that sUAS platforms carrying optical sensors can be an effective component of an integrated management plan within challenging subcanopy forest environments.

ARM Tethered Balloon System & AALCO Activities at AMF3 Site at Oliktok Point, AK

NASA Astrophysics Data System (ADS)

Hardesty, J.; Dexheimer, D.; Mei, F.; Roesler, E. L.; Longbottom, C.; Hillman, B. R.

2017-12-01

Sandia National Laboratories (SNL) has operated the Atmospheric Radiation Measurement program's (ARM) third ARM Mobile Facility (AMF3) and the restricted airspace associated with it at Oliktok Point, Alaska, since October 2013. The site hosts ground-based instrumentation which collects a variety of continuous atmospheric measurements as well as user-conducted unmanned aircraft and tethered balloon campaigns. SNL has operated ARM's tethered balloon system (TBS) as part of the Inaugural Campaigns for ARM Research using Unmanned Systems (ICARUS) since 2016. AALCO (Aerial Assessment of Liquid in Clouds at Oliktok), is an ARM Intensive Operations Period conducted by SNL at the AMF3 since 2016. The operation of the TBS during ICARUS and AALCO to altitudes above 4,000' AGL in a variety of seasons and conditions is addressed. A Distributed Temperature Sensing (DTS) system and supercooled liquid water content (SLWC) sensors have been deployed under both campaigns. The performance of these sensors is discussed and results are presented. DTS measurements and their relationship to concurrent temperature measurements from unmanned aircraft and radiosondes are shown. SLWC sensor in situ measurements are compared with microwave radiometer and radiosonde-derived measurements. Preliminary analysis of using Large Eddy Simulations to compare with the SLWC measurements reveals three-dimensional properties of the observed clouds.

Unmanned Aircraft Systems Human-in-the-Loop Controller and Pilot Acceptability Study: Collision Avoidance, Self-Separation, and Alerting Times (CASSAT)

NASA Technical Reports Server (NTRS)

Comstock, James R., Jr.; Ghatas, Rania W.; Vincent, Michael J.; Consiglio, Maria C.; Munoz, Cesar; Chamberlain, James P.; Volk, Paul; Arthur, Keith E.

2016-01-01

The Federal Aviation Administration (FAA) has been mandated by the Congressional funding bill of 2012 to open the National Airspace System (NAS) to Unmanned Aircraft Systems (UAS). With the growing use of unmanned systems, NASA has established a multi-center "UAS Integration in the NAS" Project, in collaboration with the FAA and industry, and is guiding its research efforts to look at and examine crucial safety concerns regarding the integration of UAS into the NAS. Key research efforts are addressing requirements for detect-and-avoid (DAA), self-separation (SS), and collision avoidance (CA) technologies. In one of a series of human-in-the-loop experiments, NASA Langley Research Center set up a study known as Collision Avoidance, Self-Separation, and Alerting Times (CASSAT). The first phase assessed active air traffic controller interactions with DAA systems and the second phase examined reactions to the DAA system and displays by UAS Pilots at a simulated ground control station (GCS). Analyses of the test results from Phase I and Phase II are presented in this paper. Results from the CASSAT study and previous human-in-the-loop experiments will play a crucial role in the FAA's establishment of rules, regulations, and procedures to safely, efficiently, and effectively integrate UAS into the NAS.

Applications of a high-altitude powered platform /HAPP/

NASA Technical Reports Server (NTRS)

Kuhner, M. B.

1979-01-01

The high-altitude powered platform (HAPP) is a conceptual unmanned vehicle which could be either an airship or airplane. It would keep station at an altitude of 70,000 ft above a fixed point on the ground. A microwave power transmission system would beam energy from the ground up to the HAPP to power an electric motor-driven propeller and the payload. A study of the HAPP has shown that it could potentially be a cost-competitive platform for such remote sensing applications as forest fire detection, Great Lakes ice monitoring and Coast Guard law enforcement. It also has significant potential as a communications relay platform for (among other things) direct broadcast to home TVs over a large region.

Development of a remote digital augmentation system and application to a remotely piloted research vehicle

NASA Technical Reports Server (NTRS)

Edwards, J. W.; Deets, D. A.

1975-01-01

A cost-effective approach to flight testing advanced control concepts with remotely piloted vehicles is described. The approach utilizes a ground based digital computer coupled to the remotely piloted vehicle's motion sensors and control surface actuators through telemetry links to provide high bandwidth feedback control. The system was applied to the control of an unmanned 3/8-scale model of the F-15 airplane. The model was remotely augmented; that is, the F-15 mechanical and control augmentation flight control systems were simulated by the ground-based computer, rather than being in the vehicle itself. The results of flight tests of the model at high angles of attack are discussed.

DHS S&T First Responders Group and NATO Counter UAS Proposal Interest Response.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salton, Jonathan R.

The capability, speed, size, and widespread availability of small unmanned aerial systems (sUAS) makes them a serious security concern. The enabling technologies for sUAS are rapidly evolving and so too are the threats they pose to national security. Potential threat vehicles have a small cross-section, and are difficult to reliably detect using purely ground-based systems (e.g. radar or electro-optical) and challenging to target using conventional anti-aircraft defenses. Ground-based sensors are static and suffer from interference with the earth, vegetation and other man-made structures which obscure objects at low altitudes. Because of these challenges, sUAS pose a unique and rapidly evolvingmore » threat to national security.« less

CFD Simulation of a Wing-In-Ground-Effect UAV

NASA Astrophysics Data System (ADS)

Lao, C. T.; Wong, E. T. T.

2018-05-01

This paper reports a numerical analysis on a wing section used for a Wing-In-Ground-Effect (WIG) unmanned aerial vehicle (UAV). The wing geometry was created by SolidWorks and the incompressible Reynolds-averaged Navier-Stokes (RANS) equations were solved with the Spalart–Allmaras turbulence model using CFD software ANSYS FLUENT. In FLUENT, the Spalart-Allmaras model has been implemented to use wall functions when the mesh resolution is not sufficiently fine. This might make it the best choice for relatively crude simulations on coarse meshes where accurate turbulent flow computations are not critical. The results show that the lift coefficient and lift-drag ratio derived excellent performance enhancement by ground effect. However, the moment coefficient shows inconsistency when the wing is operating in very low altitude - this is owing to the difficulty on the stability control of WIG vehicle. A drag polar estimation based on the analysis also indicated that the Oswald (or span) efficiency of the wing was improved by ground effect.

An inventory of aeronautical ground research facilities. Volume 4: Engineering flight simulation facilities

NASA Technical Reports Server (NTRS)

Pirrello, C. J.; Hardin, R. D.; Capelluro, L. P.; Harrison, W. D.

1971-01-01

The general purpose capabilities of government and industry in the area of real time engineering flight simulation are discussed. The information covers computer equipment, visual systems, crew stations, and motion systems, along with brief statements of facility capabilities. Facility construction and typical operational costs are included where available. The facilities provide for economical and safe solutions to vehicle design, performance, control, and flying qualities problems of manned and unmanned flight systems.

Orion Flight Test Architecture Benefits of MBSE Approach

NASA Technical Reports Server (NTRS)

Reed, Don; Simpson, Kim

2012-01-01

Exploration Flight Test 1 (EFT-1) is an unmanned first orbital flight test of the Multi Purpose Crew Vehicle (MPCV) Mission s purpose is to: Test Orion s ascent, on-orbit and entry capabilities Monitor critical activities Provide ground control in support of contingency scenarios Requires development of a large scale end-to-end information system network architecture To effectively communicate the scope of the end-to-end system a model-based system engineering approach was chosen.

The In-Transit Vigilant Covering Tour Problem of Routing Unmanned Ground Vehicles

DTIC Science & Technology

2012-08-01

of vertices in both vertex sets V and W, rather than exclusively in the vertex set V. A metaheuristic algorithm which follows the Greedy Randomized...window (VRPTW) approach, with the application of Java-encoded metaheuristic , was used [O’Rourke et al., 2001] for the dynamic routing of UAVs. Harder et...minimize both the two conflicting objectives; tour length and the coverage distance via a multi-objective evolutionary algorithm . This approach avoids a

Daytime Mud Detection for Unmanned Ground Vehicle Autonomous Navigation

DTIC Science & Technology

2008-12-01

disambiguate shadows from wet soil than shadows from dry soil. (a) Red band (b) NIR band (c) NDVI image (d) Brightness image wet soil Red...spectral bands to segment wet soil. Red and NIR bands (Figures 5a and 5b) can be used to generate a Normalized Difference Vegetation Index ( NDVI ...along the soil line image (Figure 5f) can be generated. The NDVI and normal distance to the soil line images can be used to segment soil from

Development and Evaluation of the Stingray, an Amphibious Maritime Interdiction Operations Unmanned Ground Vehicle

DTIC Science & Technology

2014-05-01

of Ships], Charles Griffin and Company, London, 246-261 (1908). [6] Volpich, H. & Bridge, I . C., “Paddle Wheels Pt 1: Preliminary Model Experiments...Transactions of the Institution of Engineers and Shipbuilders in Scotland, 327-380 (1955). [7] Volpich, H. & Bridge, I . C., “Paddle Wheels...Bridge, I . C., “Paddle Wheels Pt III: Ship/Model Correlation,” Transactions of the Institution of Engineers and Shipbuilders in Scotland, 512-550

Increasing the Mobility of Dismounted Marines. Small Unit Mobility Enhancement Technologies: Unmanned Ground Vehicles Market Survey

DTIC Science & Technology

2009-10-01

DARPA) Legged Squad Support System (LS3) Program. DARPA’s LS3 Program is an effort to develop a walking platform, preferably a quadruped, which...top-scoring UGV’s are track- or wheel-based; only the BigDog is a leg -based system. This presented BigDog with certain advantages (particularly...Technologies, Inc.’s ( DTI ) first location in Ranlo, North Carolina) – is a system capable of wheeled or tracked locomotion and was recently

The Small Whiskbroom Imager for atmospheric compositioN monitorinG (SWING) and its operations from an unmanned aerial vehicle (UAV) during the AROMAT campaign

NASA Astrophysics Data System (ADS)

Merlaud, Alexis; Tack, Frederik; Constantin, Daniel; Georgescu, Lucian; Maes, Jeroen; Fayt, Caroline; Mingireanu, Florin; Schuettemeyer, Dirk; Meier, Andreas Carlos; Schönardt, Anja; Ruhtz, Thomas; Bellegante, Livio; Nicolae, Doina; Den Hoed, Mirjam; Allaart, Marc; Van Roozendael, Michel

2018-01-01

The Small Whiskbroom Imager for atmospheric compositioN monitorinG (SWING) is a compact remote sensing instrument dedicated to mapping trace gases from an unmanned aerial vehicle (UAV). SWING is based on a compact visible spectrometer and a scanning mirror to collect scattered sunlight. Its weight, size, and power consumption are respectively 920 g, 27 cm × 12 cm × 8 cm, and 6 W. SWING was developed in parallel with a 2.5 m flying-wing UAV. This unmanned aircraft is electrically powered, has a typical airspeed of 100 km h-1, and can operate at a maximum altitude of 3 km. We present SWING-UAV experiments performed in Romania on 11 September 2014 during the Airborne ROmanian Measurements of Aerosols and Trace gases (AROMAT) campaign, which was dedicated to test newly developed instruments in the context of air quality satellite validation. The UAV was operated up to 700 m above ground, in the vicinity of the large power plant of Turceni (44.67° N, 23.41° E; 116 m a. s. l. ). These SWING-UAV flights were coincident with another airborne experiment using the Airborne imaging differential optical absorption spectroscopy (DOAS) instrument for Measurements of Atmospheric Pollution (AirMAP), and with ground-based DOAS, lidar, and balloon-borne in situ observations. The spectra recorded during the SWING-UAV flights are analysed with the DOAS technique. This analysis reveals NO2 differential slant column densities (DSCDs) up to 13±0.6×1016 molec cm-2. These NO2 DSCDs are converted to vertical column densities (VCDs) by estimating air mass factors. The resulting NO2 VCDs are up to 4.7±0.4×1016 molec cm-2. The water vapour DSCD measurements, up to 8±0.15×1022 molec cm-2, are used to estimate a volume mixing ratio of water vapour in the boundary layer of 0.013±0.002 mol mol-1. These geophysical quantities are validated with the coincident measurements.

LOAC: a small aerosol optical counter/sizer for ground-based and balloon measurements of the size distribution and nature of atmospheric particles - Part 2: First results from balloon and unmanned aerial vehicle flights

NASA Astrophysics Data System (ADS)

Renard, J.-B.; Dulac, F.; Berthet, G.; Lurton, T.; Vignelles, D.; Jégou, F.; Tonnelier, T.; Thaury, C.; Jeannot, M.; Couté, B.; Akiki, R.; Verdier, N.; Mallet, M.; Gensdarmes, F.; Charpentier, P.; Mesmin, S.; Duverger, V.; Dupont, J. C.; Elias, T.; Crenn, V.; Sciare, J.; Giacomoni, J.; Gobbi, M.; Hamonou, E.; Olafsson, H.; Dagsson-Waldhauserova, P.; Camy-Peyret, C.; Mazel, C.; Décamps, T.; Piringer, M.; Surcin, J.; Daugeron, D.

2015-09-01

In the companion paper (Renard et al., 2015), we have described and evaluated a new versatile optical particle counter/sizer named LOAC (Light Optical Aerosol Counter) based on scattering measurements at angles of 12 and 60° that allows some topology identification of particles (droplets, carbonaceous, salts, and mineral dust) in addition to size segregated counting in a large diameter range from 0.2 up to possibly more than 100 μm depending on sampling conditions. Its capabilities overpass those of preceding optical particle counters (OPCs) allowing the characterization of all kind of aerosols from submicronic-sized absorbing carbonaceous particles in polluted air to very coarse particles (> 10-20 μm in diameter) in desert dust plumes or fog and clouds. LOAC's light and compact design allows measurements under all kinds of balloons, on-board unmanned aerial vehicles (UAV) and at ground level. We illustrate here the first LOAC airborne results obtained from an unmanned aerial vehicle (UAV) and a variety of scientific balloons. The UAV was deployed in a peri-urban environment near Bordeaux in France. Balloon operations include (i) tethered balloons deployed in urban environments in Vienna (Austria) and Paris (France), (ii) pressurized balloons drifting in the lower troposphere over the western Mediterranean (during the Chemistry-Aerosol Mediterranean Experiment - ChArMEx campaigns), (iii) meteorological sounding balloons launched in the western Mediterranean region (ChArMEx) and from Aire-sur-l'Adour in south-western France (VOLTAIRE-LOAC campaign). More focus is put on measurements performed in the Mediterranean during (ChArMEx) and especially during African dust transport events to illustrate the original capability of balloon-borne LOAC to monitor in situ coarse mineral dust particles. In particular, LOAC has detected unexpected large particles in desert sand plumes.

Correction: Domingues Franceschini, M.H.; et al. Intercomparison of Unmanned Aerial Vehicle and Ground-Based Narrow Band Spectrometers Applied to Crop Trait Monitoring in Organic Potato Production. Sensors 2017, 17, 1428.

PubMed

Domingues Franceschini, Marston Héracles; Bartholomeus, Harm; van Apeldoorn, Dirk; Suomalainen, Juha; Kooistra, Lammert

2017-10-02

The authors would like to correct Figure 13 and Table A2, as well as the text related to the data presented in both of them, as indicated below, considering that an error in the calculations involving Equation (2), described in the Section 2.8 of the Materials and Methods Section, resulted in the communication of incorrect values [...].

Command, Control and Integration of Weaponized Unmanned Aircraft into the Air-to-Ground System

DTIC Science & Technology

2007-02-23

munitions. A synthetic aperture radar (SAR) payload is also available for the MQ-1 which allows the system to see through weather and clouds but the...SOF) can pull mensurated or “ sweetened ” coordinates for PGM engagement.70 The ISR deck should be serviced by traditional assets such as F-16s with...Operating Zone RSTA Reconnaissance, Surveillance and Target Acquisition SAR Synthetic Aperture Radar SIAP Standard Integrated Air Picture SDB

Proposed Functional Architecture and Associated Benefits Analysis of a Common Ground Control Station for Unmanned Aircraft Systems

DTIC Science & Technology

2010-03-01

143 Table 12. High Level Analysis of O&S Costs of Different Training Options...Station On station 24/7 ( ETOS 80%) On station 24/7 for 30 consecutive days ( ETOS 95%) Mission Radius ≥ 2,000 nm ≥ 3,000 nm Net Ready-KPP COMMON...Training with As-Is Unique GCS Architectures 143 The results of the analysis for BUQs I-IV are shown in Table 11. The data shows that

Remote Munitions Deployment from an Unmanned Ground Vehicle

DTIC Science & Technology

2011-08-09

pack in a series of toe lugs. Then the rear of the pack is pushed downward over a novel spring-loaded latch /release mechanism, remaining locked in...Mason, Patrick R. Griffin, Charles E. Dean Page 4 of 5 UNCLASSIFIED developments and testing, it is not secured by a latch /release mechanism...However, the locating tabs act to wedge the pack in place while still allowing it to pull free during launch. Figure 6: Munitions secured and

An Analysis of the Best Available Unmanned Ground Vehicle in the Current Market with Respect to the Requirements of the Turkish Ministry of National Defense

DTIC Science & Technology

2011-12-01

Special Weapons and Tactics SWORDS Special Weapons Observation Remote Reconnaissance Direct Action System TAF Turkish Armed Forces tEODor...especially concentrated in the southeastern part of Turkey where the Turkish Armed Forces ( TAF ) are fighting against terrorists determinedly and continuously...Systems (MDS) to strengthen the TAF and to modernize its current systems. Today, many countries are making large investments to strengthen their

Modeling and Simulation Behavior Validation Methodology and Extension Model Validation for the Individual Soldier

DTIC Science & Technology

2015-03-01

domains. Major model functions include: • Ground combat: Light and heavy forces. • Air mobile forces. • Future forces. • Fixed-wing and rotary-wing...Constraints: • Study must be completed no later than 31 December 2014. • Entity behavior limited to select COMBATXXI Mobility , Unmanned Aerial System...and SQL backend , as well as any open application programming interface API. • Allows data transparency and data driven navigation through the model

Fault Diagnosis and Prognosis Based on Lebesgue Sampling

DTIC Science & Technology

2014-10-02

required for many safety critical systems such as unmanned air/ground/sea vehicles, aircraft , power generation, nuclear power plants, and various industrial...prediction horizon in the fault dimen- sion axis and described by the number fo fault states. This provides a straightforward means to conduct prognosis that...shown in Figure 2.(b), only 5 Lebesgue states are visited during the 550 cycles in R1 and 4 states during the 100 cycles in R2, which means that the

Characteristics of a Maritime Interdiction Operations Unmanned Ground Vehicle

DTIC Science & Technology

2012-04-01

obstacles taller than its height. It comes with a suite of software that provides behaviors such as automatic self-righting and stair climbing (although the...unit we tested was a prototype and the stair climbing behavior had not been perfected). It also has a small wrist-mounted OCU with a touch screen...operations, often in hostile environments. There is a need for a small tactical robot that can be deployed ahead of the team to provide enhanced

On The Lookout: The Air Mobile Ground Security and Surveillance System (AMGSS) Has Arrived

DTIC Science & Technology

1995-01-01

dimensional mobility allowed by the VTOL platform are ideally suited to this concept. If (during landing) there is loss of communications detected on the...vertical-take-off-and-landing, unmanned aircraft) with a sensor pod mounted on top as shown in figure 3. Projected weight of the mission-ready AMP...to restart the engine twice. Weight and power estimates are based on commercially available hardware, modified in some cases for the AMGSSS

LOAC: a small aerosol optical counter/sizer for ground-based and balloon measurements of the size distribution and nature of atmospheric particles - Part 2: First results from balloon and unmanned aerial vehicle flights

NASA Astrophysics Data System (ADS)

Renard, J.-B.; Dulac, F.; Berthet, G.; Lurton, T.; Vignelle, D.; Jégou, F.; Tonnelier, T.; Thaury, C.; Jeannot, M.; Couté, B.; Akiki, R.; Mineau, J.-L.; Verdier, N.; Mallet, M.; Gensdarmes, F.; Charpentier, P.; Mesmin, S.; Duverger, V.; Dupont, J.-C.; Elias, T.; Crenn, V.; Sciare, J.; Giacomoni, J.; Gobbi, M.; Hamonou, E.; Olafsson, H.; Dagsson-Waldhauserova, P.; Camy-Peyret, C.; Mazel, C.; Décamps, T.; Piringer, M.; Surcin, J.; Daugeron, D.

2015-01-01

In a companion (Part 1) paper (Renard et al., 2015), we have described and evaluated a new versatile optical particle counter/sizer named LOAC (Light Optical Aerosols Counter) based on scattering measurements at angles of 12 and 60°. that allows some speciation of particles (droplets, carbonaceous, salts, and mineral dust) in addition to size segregated counting in a large diameter range from 0.2 up to possibly more than 100 μm depending on sampling conditions. Its capabilities overwhelm those of preceding optical particle counters (OPCs) allowing the characterization of all kind of aerosols from submicronic-sized absorbing carbonaceous particles in polluted air to very coarse particles (> 10-20 μm in diameter) in desert dust plumes or fog and clouds. LOAC light and compact design allows measurements under all kinds of balloons, on-board unmanned aerial vehicles (UAV) and at ground level. We illustrate here the first LOAC airborne results obtained from an unmanned aerial vehicle (UAV) and a variety of scientific balloons. The UAV was deployed in a peri-urban environment near Bordeaux in France. Balloon operations include (i) tethered balloons deployed in urban environments in Wien (Austria) and Paris (France), (ii) pressurized balloons drifting in the lower troposphere over the western Mediterranean (during the Chemistry-Aerosol Mediterranean Experiment - ChArMEx campaigns), (iii) meteorological sounding balloons launched in the western Mediterranean region (ChArMEx) and from Aire-sur-l'Adour in south-western France (VOLTAIRE-LOAC campaign). More focus is put on measurements performed in the Mediterranean during (ChArMEx) and especially during African dust transport events to illustrate the original capability of balloon-borne LOAC to monitor in situ coarse mineral dust particles. In particular, LOAC has detected unexpected large particles in desert sand plumes.

UAV-guided navigation for ground robot tele-operation in a military reconnaissance environment.

PubMed

Chen, Jessie Y C

2010-08-01

A military reconnaissance environment was simulated to examine the performance of ground robotics operators who were instructed to utilise streaming video from an unmanned aerial vehicle (UAV) to navigate his/her ground robot to the locations of the targets. The effects of participants' spatial ability on their performance and workload were also investigated. Results showed that participants' overall performance (speed and accuracy) was better when she/he had access to images from larger UAVs with fixed orientations, compared with other UAV conditions (baseline- no UAV, micro air vehicle and UAV with orbiting views). Participants experienced the highest workload when the UAV was orbiting. Those individuals with higher spatial ability performed significantly better and reported less workload than those with lower spatial ability. The results of the current study will further understanding of ground robot operators' target search performance based on streaming video from UAVs. The results will also facilitate the implementation of ground/air robots in military environments and will be useful to the future military system design and training community.

Global Versus Reactive Navigation for Joint UAV-UGV Missions in a Cluttered Environment

DTIC Science & Technology

2012-06-01

spaces. The vehicle uses a two- wheel 5 differential drive system with a third omnidirectional caster for balance. This uncomplicated system saves... wheels , two differential drive wheels and one omni- directional caster wheel . The vehicle changes the direction of its movement by altering the speed of...Virtual Speed Versus Time..........64  Figure 23:  Heading and Yaw Rate Versus Time................64  Figure 24:  Individual Wheel Speeds Versus Time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz-Fellenz, Emily S.

A portion of LANL’s FY15 SPE objectives includes initial ground-based or ground-proximal investigations at the SPE Phase 2 site. The area of interest is the U2ez location in Yucca Flat. This collection serves as a baseline for discrimination of surface features and acquisition of topographic signatures prior to any development or pre-shot activities associated with SPE Phase 2. Our team originally intended to perform our field investigations using previously vetted ground-based (GB) LIDAR methodologies. However, the extended proposed time frame of the GB LIDAR data collection, and associated data processing time and delivery date, were unacceptable. After technical consultation andmore » careful literature research, LANL identified an alternative methodology to achieve our technical objectives and fully support critical model parameterization. Very-low-altitude unmanned aerial systems (UAS) photogrammetry appeared to satisfy our objectives in lieu of GB LIDAR. The SPE Phase 2 baseline collection was used as a test of this UAS photogrammetric methodology.« less

Repeated aeromagnetic surveys in Shinmoe-dake volcano, Japan by using unmanned helicopter

NASA Astrophysics Data System (ADS)

Koyama, T.; Kaneko, T.; Ohminato, T.; Watanabe, A.; Takeo, M.; Yanagisawa, T.; Honda, Y.

2016-12-01

We repeatedly conducted aeromagnetic surveys at Shinmoe-dake volcano, Japan by using unmanned helicopter, and elucidated magnetization structure and its temporal change. At the beginning of 2011, Shinmoe-dake volcano has done magmatic eruptions. After ceasing activities of volcanic eruptions, the first aeromagnetic survey by an unmanned helicopter was performed in the western part of Shinmoe-dake volcano in May 2011. The advantage to use unmanned vehicle for volcanic survey is ability of the safe flight in lower altitude with precise tracks. It enable us forthcoming repeated survey on the same tracks and elucidate the temporal changes of the magnetic fields. The geomagnetic total intensity measurement flight was conducted by installing cesium optical pumping magnetometer on the helicopter, in which the measurement line intervals were almost 100 m and the altitudes were also fixed at almost 100 m above the ground except above the crater. Total measurement length was about 85 km. The data analysis revealed that the averaged magnetization is about 1.5 A/m, typical value of andesite rock, and some horizontal anomalies can be shown.After that, we conducted four repeated surveys so far, and notable temporal changes are detected just around the crater of Shinmoe-dake volcano due to gaining magnetization by cooling of lava which has accumulated in the crater at the 2011 eruptions. The cooling rate just follows square root of elapsed time from the eruptive events, and thus the cooling is being simply done by thermal diffusion. Magnetizing, however, goes on too fast to be done by thermal diffusion only at the surface of lava, and so the cooling may be very effectively done also inside the lava by evaporating water.In this paper, we'll show the detailed results of measurements and discuss the temporal changes of magnetization.

Detecting Surface Changes from an Underground Explosion in Granite Using Unmanned Aerial System Photogrammetry

NASA Astrophysics Data System (ADS)

Schultz-Fellenz, Emily S.; Coppersmith, Ryan T.; Sussman, Aviva J.; Swanson, Erika M.; Cooley, James A.

2017-08-01

Efficient detection and high-fidelity quantification of surface changes resulting from underground activities are important national and global security efforts. In this investigation, a team performed field-based topographic characterization by gathering high-quality photographs at very low altitudes from an unmanned aerial system (UAS)-borne camera platform. The data collection occurred shortly before and after a controlled underground chemical explosion as part of the United States Department of Energy's Source Physics Experiments (SPE-5) series. The high-resolution overlapping photographs were used to create 3D photogrammetric models of the site, which then served to map changes in the landscape down to 1-cm-scale. Separate models were created for two areas, herein referred to as the test table grid region and the nearfield grid region. The test table grid includes the region within 40 m from surface ground zero, with photographs collected at a flight altitude of 8.5 m above ground level (AGL). The near-field grid area covered a broader area, 90-130 m from surface ground zero, and collected at a flight altitude of 22 m AGL. The photographs, processed using Agisoft Photoscan® in conjunction with 125 surveyed ground control point targets, yielded a 6-mm pixel-size digital elevation model (DEM) for the test table grid region. This provided the ≤3 cm resolution in the topographic data to map in fine detail a suite of features related to the underground explosion: uplift, subsidence, surface fractures, and morphological change detection. The near-field grid region data collection resulted in a 2-cm pixel-size DEM, enabling mapping of a broader range of features related to the explosion, including: uplift and subsidence, rock fall, and slope sloughing. This study represents one of the first works to constrain, both temporally and spatially, explosion-related surface damage using a UAS photogrammetric platform; these data will help to advance the science of underground explosion detection.

Georeferencing UAS Derivatives Through Point Cloud Registration with Archived Lidar Datasets

NASA Astrophysics Data System (ADS)

Magtalas, M. S. L. Y.; Aves, J. C. L.; Blanco, A. C.

2016-10-01

Georeferencing gathered images is a common step before performing spatial analysis and other processes on acquired datasets using unmanned aerial systems (UAS). Methods of applying spatial information to aerial images or their derivatives is through onboard GPS (Global Positioning Systems) geotagging, or through tying of models through GCPs (Ground Control Points) acquired in the field. Currently, UAS (Unmanned Aerial System) derivatives are limited to meter-levels of accuracy when their generation is unaided with points of known position on the ground. The use of ground control points established using survey-grade GPS or GNSS receivers can greatly reduce model errors to centimeter levels. However, this comes with additional costs not only with instrument acquisition and survey operations, but also in actual time spent in the field. This study uses a workflow for cloud-based post-processing of UAS data in combination with already existing LiDAR data. The georeferencing of the UAV point cloud is executed using the Iterative Closest Point algorithm (ICP). It is applied through the open-source CloudCompare software (Girardeau-Montaut, 2006) on a `skeleton point cloud'. This skeleton point cloud consists of manually extracted features consistent on both LiDAR and UAV data. For this cloud, roads and buildings with minimal deviations given their differing dates of acquisition are considered consistent. Transformation parameters are computed for the skeleton cloud which could then be applied to the whole UAS dataset. In addition, a separate cloud consisting of non-vegetation features automatically derived using CANUPO classification algorithm (Brodu and Lague, 2012) was used to generate a separate set of parameters. Ground survey is done to validate the transformed cloud. An RMSE value of around 16 centimeters was found when comparing validation data to the models georeferenced using the CANUPO cloud and the manual skeleton cloud. Cloud-to-cloud distance computations of CANUPO and manual skeleton clouds were obtained with values for both equal to around 0.67 meters at 1.73 standard deviation.

Detecting Surface Changes from an Underground Explosion in Granite Using Unmanned Aerial System Photogrammetry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz-Fellenz, Emily S.; Coppersmith, Ryan T.; Sussman, Aviva J.

Efficient detection and high-fidelity quantification of surface changes resulting from underground activities are important national and global security efforts. In this investigation, a team performed field-based topographic characterization by gathering high-quality photographs at very low altitudes from an unmanned aerial system (UAS)-borne camera platform. The data collection occurred shortly before and after a controlled underground chemical explosion as part of the United States Department of Energy’s Source Physics Experiments (SPE-5) series. The high-resolution overlapping photographs were used to create 3D photogrammetric models of the site, which then served to map changes in the landscape down to 1-cm-scale. Separate models weremore » created for two areas, herein referred to as the test table grid region and the nearfield grid region. The test table grid includes the region within ~40 m from surface ground zero, with photographs collected at a flight altitude of 8.5 m above ground level (AGL). The near-field grid area covered a broader area, 90–130 m from surface ground zero, and collected at a flight altitude of 22 m AGL. The photographs, processed using Agisoft Photoscan® in conjunction with 125 surveyed ground control point targets, yielded a 6-mm pixel-size digital elevation model (DEM) for the test table grid region. This provided the ≤3 cm resolution in the topographic data to map in fine detail a suite of features related to the underground explosion: uplift, subsidence, surface fractures, and morphological change detection. The near-field grid region data collection resulted in a 2-cm pixel-size DEM, enabling mapping of a broader range of features related to the explosion, including: uplift and subsidence, rock fall, and slope sloughing. This study represents one of the first works to constrain, both temporally and spatially, explosion-related surface damage using a UAS photogrammetric platform; these data will help to advance the science of underground explosion detection.« less

Ground operation of robotics on Space Station Freedom

NASA Technical Reports Server (NTRS)

Wojcik, Z. Alex; Hunter, David G.; Cantin, Marc R.

1993-01-01

This paper reflects work carried out on Ground Operated Telerobotics (GOT) in 1992 to refine further the ideas, procedures, and technologies needed to test the procedures in a high latency environment, and to integrate GOT into Space Station Freedom operations. Space Station Freedom (SSF) will be in operation for 30 years, and will depend on robots to carry out a significant part of the assembly, maintenance, and utilization workload. Current plans call for on-orbit robotics to be operated by on-board crew members. This approach implies that on-orbit robotics operations use up considerable crew time, and that these operations cannot be carried out when SSF is unmanned. GOT will allow robotic operations to be operated from the ground, with on-orbit crew interventions only when absolutely required. The paper reviews how GOT would be implemented, how GOT operations would be planned and supported, and reviews GOT issues, critical success factors, and benefits.

High-performance two-axis gimbal system for free space laser communications onboard unmanned aircraft systems

NASA Astrophysics Data System (ADS)

Locke, Michael; Czarnomski, Mariusz; Qadir, Ashraf; Setness, Brock; Baer, Nicolai; Meyer, Jennifer; Semke, William H.

2011-03-01

A custom designed and manufactured gimbal with a wide field-of-view and fast response time is developed. This enhanced custom design is a 24 volt system with integrated motor controllers and drivers which offers a full 180o fieldof- view in both azimuth and elevation; this provides a more continuous tracking capability as well as increased velocities of up to 479° per second. The addition of active high-frequency vibration control, to complement the passive vibration isolation system, is also in development. The ultimate goal of this research is to achieve affordable, reliable, and secure air-to-air laser communications between two separate remotely piloted aircraft. As a proof-of-concept, the practical implementation of an air-to-ground laserbased video communications payload system flown by a small Unmanned Aerial Vehicle (UAV) will be demonstrated. A numerical tracking algorithm has been written, tested, and used to aim the airborne laser transmitter at a stationary ground-based receiver with known GPS coordinates; however, further refinement of the tracking capabilities is dependent on an improved gimbal design for precision pointing of the airborne laser transmitter. The current gimbal pointing system is a two-axis, commercial-off-the-shelf component, which is limited in both range and velocity. The current design is capable of 360o of pan and 78o of tilt at a velocity of 60o per second. The control algorithm used for aiming the gimbal is executed on a PC-104 format embedded computer onboard the payload to accurately track a stationary ground-based receiver. This algorithm autonomously calculates a line-of-sight vector in real-time by using the UAV autopilot's Differential Global Positioning System (DGPS) which provides latitude, longitude, and altitude and Inertial Measurement Unit (IMU) which provides the roll, pitch, and yaw data, along with the known Global Positioning System (GPS) location of the ground-based photodiode array receiver.

Mobile Robotics Activities in DOE Laboratories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ron Lujan; Jerry Harbour; John T. Feddema

This paper will briefly outline major activities in Department of Energy (DOE) Laboratories focused on mobile platforms, both Unmanned Ground Vehicles (UGV’s) as well as Unmanned Air Vehicles (UAV’s). The activities will be discussed in the context of the science and technology construct used by the DOE Technology Roadmap for Robotics and Intelligent Machines (RIM)1 published in 1998; namely, Perception, Reasoning, Action, and Integration. The activities to be discussed span from research and development to deployment in field operations. The activities support customers in other agencies. The discussion of "perception" will include hyperspectral sensors, complex patterns discrimination, multisensor fusion andmore » advances in LADAR technologies, including real-world perception. "Reasoning" activities to be covered include cooperative controls, distributed systems, ad-hoc networks, platform-centric intelligence, and adaptable communications. The paper will discuss "action" activities such as advanced mobility and various air and ground platforms. In the RIM construct, "integration" includes the Human-Machine Integration. Accordingly the paper will discuss adjustable autonomy and the collaboration of operator(s) with distributed UGV’s and UAV’s. Integration also refers to the applications of these technologies into systems to perform operations such as perimeter surveillance, large-area monitoring and reconnaissance. Unique facilities and test beds for advanced mobile systems will be described. Given that this paper is an overview, rather than delve into specific detail in these activities, other more exhaustive references and sources will be cited extensively.« less

Comparison of Unmanned Aerial Vehicle Platforms for Assessing Vegetation Cover in Sagebrush Steppe Ecosystems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert P. Breckenridge; Maxine Dakins; Stephen Bunting

2011-09-01

In this study, the use of unmanned aerial vehicles (UAVs) as a quick and safe method for monitoring biotic resources was evaluated. Vegetation cover and the amount of bare ground are important factors in understanding the sustainability of many ecosystems and assessment of rangeland health. Methods that improve speed and cost efficiency could greatly improve how biotic resources are monitored on western lands. Sagebrush steppe ecosystems provide important habitat for a variety of species (including sage grouse and pygmy rabbit). Improved methods are needed to support monitoring these habitats because there are not enough resource specialists or funds available formore » comprehensive ground evaluations. In this project, two UAV platforms, fixed wing and helicopter, were used to collect still-frame imagery to assess vegetation cover in sagebrush steppe ecosystems. This paper discusses the process for collecting and analyzing imagery from the UAVs to (1) estimate percent cover for six different vegetation types (shrub, dead shrub, grass, forb, litter, and bare ground) and (2) locate sage grouse using representative decoys. The field plots were located on the Idaho National Engineering (INL) site west of Idaho Falls, Idaho, in areas with varying amounts and types of vegetation cover. A software program called SamplePoint was used along with visual inspection to evaluate percent cover for the six cover types. Results were compared against standard field measurements to assess accuracy. The comparison of fixed-wing and helicopter UAV technology against field estimates shows good agreement for the measurement of bare ground. This study shows that if a high degree of detail and data accuracy is desired, then a helicopter UAV may be a good platform to use. If the data collection objective is to assess broad-scale landscape level changes, then the collection of imagery with a fixed-wing system is probably more appropriate.« less

Ground operation of robotics on Space Station Freedom

NASA Astrophysics Data System (ADS)

Wojcik, Z. Alex; Hunter, David G.; Cantin, Marc R.

1993-03-01

This paper reflects work carried out on Ground Operated Telerobotics (GOT) in 1992 to refine further the ideas, procedures, and technologies needed to test the procedures in a high latency environment, and to integrate GOT into Space Station Freedom operations. Space Station Freedom (SSF) will be in operation for 30 years, and will depend on robots to carry out a significant part of the assembly, maintenance, and utilization workload. Current plans call for on-orbit robotics to be operated by on-board crew members. This approach implies that on-orbit robotics operations use up considerable crew time, and that these operations cannot be carried out when SSF is unmanned. GOT will allow robotic operations to be operated from the ground, with on-orbit crew interventions only when absolutely required. The paper reviews how GOT would be implemented, how GOT operations would be planned and supported, and reviews GOT issues, critical success factors, and benefits.

Turnaround operations analysis for OTV. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1988-01-01

Anaylses performed for ground processing, both expendable and reusable ground-based Orbital Transfer Vehicles (OTVs) launched on the Space Transportation System (STS), a reusable space-based OTV (SBOTV) launched on the STS, and a reusable ground-based OTV (GBOTV) launched on an unmanned cargo vehicle and recovered by the Orbiter are summarized. Also summarized are the analyses performed for space processing the reusable SBOTV at the Space Station in low Earth orbit (LEO) as well as the maintenance and servicing of the SBOTV accommodations at the Space Station. In addition, the candidate OTV concepts, design and interface requirements, and the Space Station design, support, and interface requirements are summarized. A development schedule and associated costs for the required SBOTV accommodations at the Space Station are presented. Finallly, the technology development plan to develop the capability to process both GBOTVs and SBOTVs are summarized.

UAV field demonstration of social media enabled tactical data link

NASA Astrophysics Data System (ADS)

Olson, Christopher C.; Xu, Da; Martin, Sean R.; Castelli, Jonathan C.; Newman, Andrew J.

2015-05-01

This paper addresses the problem of enabling Command and Control (C2) and data exfiltration functions for missions using small, unmanned, airborne surveillance and reconnaissance platforms. The authors demonstrated the feasibility of using existing commercial wireless networks as the data transmission infrastructure to support Unmanned Aerial Vehicle (UAV) autonomy functions such as transmission of commands, imagery, metadata, and multi-vehicle coordination messages. The authors developed and integrated a C2 Android application for ground users with a common smart phone, a C2 and data exfiltration Android application deployed on-board the UAVs, and a web server with database to disseminate the collected data to distributed users using standard web browsers. The authors performed a mission-relevant field test and demonstration in which operators commanded a UAV from an Android device to search and loiter; and remote users viewed imagery, video, and metadata via web server to identify and track a vehicle on the ground. Social media served as the tactical data link for all command messages, images, videos, and metadata during the field demonstration. Imagery, video, and metadata were transmitted from the UAV to the web server via multiple Twitter, Flickr, Facebook, YouTube, and similar media accounts. The web server reassembled images and video with corresponding metadata for distributed users. The UAV autopilot communicated with the on-board Android device via on-board Bluetooth network.

Detecting Surface Changes from an Underground Explosion in Granite Using Unmanned Aerial System Photogrammetry

DOE PAGES

Schultz-Fellenz, Emily S.; Coppersmith, Ryan T.; Sussman, Aviva J.; ...

2017-08-19

Efficient detection and high-fidelity quantification of surface changes resulting from underground activities are important national and global security efforts. In this investigation, a team performed field-based topographic characterization by gathering high-quality photographs at very low altitudes from an unmanned aerial system (UAS)-borne camera platform. The data collection occurred shortly before and after a controlled underground chemical explosion as part of the United States Department of Energy’s Source Physics Experiments (SPE-5) series. The high-resolution overlapping photographs were used to create 3D photogrammetric models of the site, which then served to map changes in the landscape down to 1-cm-scale. Separate models weremore » created for two areas, herein referred to as the test table grid region and the nearfield grid region. The test table grid includes the region within ~40 m from surface ground zero, with photographs collected at a flight altitude of 8.5 m above ground level (AGL). The near-field grid area covered a broader area, 90–130 m from surface ground zero, and collected at a flight altitude of 22 m AGL. The photographs, processed using Agisoft Photoscan® in conjunction with 125 surveyed ground control point targets, yielded a 6-mm pixel-size digital elevation model (DEM) for the test table grid region. This provided the ≤3 cm resolution in the topographic data to map in fine detail a suite of features related to the underground explosion: uplift, subsidence, surface fractures, and morphological change detection. The near-field grid region data collection resulted in a 2-cm pixel-size DEM, enabling mapping of a broader range of features related to the explosion, including: uplift and subsidence, rock fall, and slope sloughing. This study represents one of the first works to constrain, both temporally and spatially, explosion-related surface damage using a UAS photogrammetric platform; these data will help to advance the science of underground explosion detection.« less

Design, testing and demonstration of a small unmanned aircraft system (sUAS) and payload for measuring wind speed and particulate matter in the atmospheric boundary layer

NASA Astrophysics Data System (ADS)

Riddell, Kevin Donald Alexander

The atmospheric boundary layer (ABL) is the layer of air directly influenced by the Earth's surface and is the layer of the atmosphere most important to humans as this is the air we live in. Methods for measuring the properties of the ABL include three general approaches: satellite based, ground based and airborne. A major research challenge is that many contemporary methods provide a restricted spatial resolution or coverage of variations of ABL properties such as how wind speed varies across a landscape with complex topography. To enhance our capacity to measure the properties of the ABL, this thesis presents a new technique that involves a small unmanned aircraft system (sUAS) equipped with a customized payload for measuring wind speed and particulate matter. The research presented herein outlines two key phases in establishing the proof of concept of the payload and its integration on the sUAS: (1) design and testing and (2) field demonstration. The first project focuses on measuring wind speed, which has been measured with fixed wing sUASs in previous research. but not with a helicopter sUAS. The second project focuses on the measurement of particulate matter, which is a major air pollutant typically measured with ground-based sensors. Results from both proof of concept projects suggest that ABL research could benefit from the proposed techniques. .

Development of a low cost unmanned aircraft system for atmospheric carbon dioxide leak detection

NASA Astrophysics Data System (ADS)

Mitchell, Taylor Austin

Carbon sequestration, the storage of carbon dioxide gas underground, has the potential to reduce global warming by removing a greenhouse gas from the atmosphere. These storage sites, however, must first be monitored to detect if carbon dioxide is leaking back out to the atmosphere. As an alternative to traditional large ground-based sensor networks to monitor CO2 levels for leaks, unmanned aircraft offer the potential to perform in-situ atmospheric leak detection over large areas for a fraction of the cost. This project developed a proof-of-concept sensor system to map relative carbon dioxide levels to detect potential leaks. The sensor system included a Sensair K-30 FR CO2 sensor, GPS, and altimeter connected an Arduino microcontroller which logged data to an onboard SD card. Ground tests were performed to verify and calibrate the system including wind tunnel tests to determine the optimal configuration of the system for the quickest response time (4-8 seconds based upon flowrate). Tests were then conducted over a controlled release of CO 2 in addition to over controlled rangeland fires which released carbon dioxide over a large area as would be expected from a carbon sequestration source. 3D maps of carbon dioxide were developed from the system telemetry that clearly illustrated increased CO2 levels from the fires. These tests demonstrated the system's ability to detect increased carbon dioxide concentrations in the atmosphere.

Flight Test Result for the Ground-Based Radio Navigation System Sensor with an Unmanned Air Vehicle

PubMed Central

Jang, Jaegyu; Ahn, Woo-Guen; Seo, Seungwoo; Lee, Jang Yong; Park, Jun-Pyo

2015-01-01

The Ground-based Radio Navigation System (GRNS) is an alternative/backup navigation system based on time synchronized pseudolites. It has been studied for some years due to the potential vulnerability issue of satellite navigation systems (e.g., GPS or Galileo). In the framework of our study, a periodic pulsed sequence was used instead of the randomized pulse sequence recommended as the RTCM (radio technical commission for maritime services) SC (special committee)-104 pseudolite signal, as a randomized pulse sequence with a long dwell time is not suitable for applications requiring high dynamics. This paper introduces a mathematical model of the post-correlation output in a navigation sensor, showing that the aliasing caused by the additional frequency term of a periodic pulsed signal leads to a false lock (i.e., Doppler frequency bias) during the signal acquisition process or in the carrier tracking loop of the navigation sensor. We suggest algorithms to resolve the frequency false lock issue in this paper, relying on the use of a multi-correlator. A flight test with an unmanned helicopter was conducted to verify the implemented navigation sensor. The results of this analysis show that there were no false locks during the flight test and that outliers stem from bad dilution of precision (DOP) or fluctuations in the received signal quality. PMID:26569251

Photovoltaic electric power applied to Unmanned Aerial Vehicles (UAV)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geis, J.; Arnold, J.H.

1994-09-01

Photovoltaic electric-powered flight is receiving a great deal of attention in the context of the United States` Unmanned Aerial Vehicle (UAV) program. This paper addresses some of the enabling technical areas and their potential solutions. Of particular interest are the long-duration, high-altitude class of UAV`s whose mission it is to achieve altitudes between 60,000 and 100,000 feet, and to remain at those altitudes for prolonged periods performing various mapping and surveillance activities. Addressed herein are studies which reveal the need for extremely light-weight and efficient solar cells, high-efficiency electric motor-driven propeller modules, and power management and distribution control elements. Sincemore » the potential payloads vary dramatically in their power consumption and duty cycles, a typical load profile has been selected to provide commonality for the propulsion power comparisons. Since missions vary widely with respect to ground coverage requirements, from repeated orbiting over a localized target to long-distance routes over irregular terrain, the authors have also averaged the power requirements for on-board guidance and control power, as well as ground control and communication link utilization. In the context of the national technology reinvestment program, wherever possible they modeled components and materials which have been qualified for space and defense applications, yet are compatible with civilian UAV activities. These include, but are not limited to, solar cell developments, electric storage technology for diurnal operation, local and ground communications, power management and distribution, and control servo design. And finally, the results of tests conducted by Wright Laboratory on ultralight, highly efficient MOCVD GaAs solar cells purchased from EPI Materials Ltd. (EML) of the UK are presented. These cells were also used for modeling the flight characteristics of UAV aircraft.« less

Seasonal associations and atmospheric transport distances of fungi in the genus Fusarium collected with unmanned aerial vehicles and ground-based sampling devices

NASA Astrophysics Data System (ADS)

Lin, Binbin; Ross, Shane D.; Prussin, Aaron J.; Schmale, David G.

2014-09-01

Spores of fungi in the genus Fusarium may be transported through the atmosphere over long distances. New information is needed to characterize seasonal trends in atmospheric loads of Fusarium and to pinpoint the source(s) of inoculum at both local (farm) and regional (state or country) scales. We hypothesized that (1) atmospheric concentrations of Fusarium spores in an agricultural ecosystem vary with height and season and (2) transport distances from potential inoculum source(s) vary with season. To test these hypotheses, spores of Fusarium were collected from the atmosphere in an agricultural ecosystem in Blacksburg, VA, USA using a Burkard volumetric sampler (BVS) 1 m above ground level and autonomous unmanned aerial vehicles (UAVs) 100 m above ground level. More than 2200 colony forming units (CFUs) of Fusarium were collected during 104 BVS sampling periods and 180 UAV sampling periods over four calendar years (2009-2012). Spore concentrations ranged from 0 to 13 and 0 to 23 spores m-3 for the BVS and the UAVs, respectively. Spore concentrations were generally higher in the fall, spring, and summer, and lower in the winter. Spore concentrations from the BVS were generally higher than those from the UAVs for both seasonal and hourly collections. A Gaussian plume transport model was used to estimate distances to the potential inoculum source(s) by season, and produced mean transport distances of 1.4 km for the spring, 1.7 km for the summer, 1.2 km for the fall, and 4.1 km for the winter. Environmental signatures that predict atmospheric loads of Fusarium could inform disease spread, air pollution, and climate change.

Photovoltaic electric power applied to Unmanned Aerial Vehicles (UAV)

NASA Astrophysics Data System (ADS)

Geis, Jack; Arnold, Jack H.

1994-09-01

Photovoltaic electric-powered flight is receiving a great deal of attention in the context of the United States' Unmanned Aerial Vehicle (UAV) program. This paper addresses some of the enabling technical areas and their potential solutions. Of particular interest are the long-duration, high-altitude class of UAV's whose mission it is to achieve altitudes between 60,000 and 100,000 feet, and to remain at those altitudes for prolonged periods performing various mapping and surveillance activities. Addressed herein are studies which reveal the need for extremely light-weight and efficient solar cells, high-efficiency electric motor-driven propeller modules, and power management and distribution control elements. Since the potential payloads vary dramatically in their power consumption and duty cycles, a typical load profile has been selected to provide commonality for the propulsion power comparisons. Since missions vary widely with respect to ground coverage requirements, from repeated orbiting over a localized target to long-distance routes over irregular terrain, we have also averaged the power requirements for on-board guidance and control power, as well as ground control and communication link utilization. In the context of the national technology reinvestment program, wherever possible we modeled components and materials which have been qualified for space and defense applications, yet are compatible with civilian UAV activities. These include, but are not limited to, solar cell developments, electric storage technology for diurnal operation, local and ground communications, power management and distribution, and control servo design. And finally, the results of tests conducted by Wright Laboratory on ultralight, highly efficient MOCVD GaAs solar cells purchased from EPI Materials Ltd. (EML) of the UK are presented. These cells were also used for modeling the flight characteristics of UAV aircraft.

Team Cappadocia Design for MAGIC 2010 (The ASELSAN Team)

DTIC Science & Technology

2010-11-01

Also in another screen, OCU displays tactical information using 3D Geographical Information System (GIS) for enhanced situational awareness. OCU...number of local textural features such as mean and standard deviation of image intensity and gradient, Zernike moments, Haralick features...information for situational awareness on the 3D GIS tactical map and the other monitor is used for UGV status monitoring, command and control. Tactical

Practical Applications of Cosmic Ray Science: Spacecraft, Aircraft, Ground Based Computation and Control Systems and Human Health and Safety

NASA Technical Reports Server (NTRS)

Atwell, William; Koontz, Steve; Normand, Eugene

2012-01-01

In this paper we review the discovery of cosmic ray effects on the performance and reliability of microelectronic systems as well as on human health and safety, as well as the development of the engineering and health science tools used to evaluate and mitigate cosmic ray effects in earth surface, atmospheric flight, and space flight environments. Three twentieth century technological developments, 1) high altitude commercial and military aircraft; 2) manned and unmanned spacecraft; and 3) increasingly complex and sensitive solid state micro-electronics systems, have driven an ongoing evolution of basic cosmic ray science into a set of practical engineering tools (e.g. ground based test methods as well as high energy particle transport and reaction codes) needed to design, test, and verify the safety and reliability of modern complex electronic systems as well as effects on human health and safety. The effects of primary cosmic ray particles, and secondary particle showers produced by nuclear reactions with spacecraft materials, can determine the design and verification processes (as well as the total dollar cost) for manned and unmanned spacecraft avionics systems. Similar considerations apply to commercial and military aircraft operating at high latitudes and altitudes near the atmospheric Pfotzer maximum. Even ground based computational and controls systems can be negatively affected by secondary particle showers at the Earth's surface, especially if the net target area of the sensitive electronic system components is large. Accumulation of both primary cosmic ray and secondary cosmic ray induced particle shower radiation dose is an important health and safety consideration for commercial or military air crews operating at high altitude/latitude and is also one of the most important factors presently limiting manned space flight operations beyond low-Earth orbit (LEO).

Distributed sounding of the boundary layer using multiple unmanned aerial systems during the ScaleX campaign 2016

NASA Astrophysics Data System (ADS)

Philipp, Andreas; Petersen, Erik; Groos, Alexander; Ferenci, Pia; Engerer, Stefan; Fiedler, Benedikt; Emeis, Stefan; Schäfer, Klaus; Brosy, Caroline; Zeeman, Matthias; Jacobeit, Jucundus

2017-04-01

In order to observe and better understand micro scale processes of interaction between the surface and the atmosphere and to relate them to meso and macro scale processes, an intensive measurement campaign at the TERENO (Terrestrial Environmental Observatories) site Fendt in southern Germany was organized in summer 2016 by IMK-IFU (Institute of Meteorology and Climate Research - Atmospheric Environmental Research) / KIT (Karlsruher Institute for Technology) under participation of a large number of cooperation partners. While several ground based remote sensing systems were implemented beside already installed long-term observing instruments for turbulence, soil moisture, trace gas emission etc., several flight campaigns with unmanned aerial systems took place. IGUA (Institute for Geography at the Universiy of Augsburg) contributed with spiral profile flights up to 1000 meters above ground level simultaneously at five locations, covering an 1 km x 1 km large area, corresponding to a WRF (Weather and Research Forecast model) grid box. Starting in the afternoon of 6th of July and ending in the morning of 7th of July each full hour an ascent was launched. While there were several technical problems leading to missing values, an all together useful dataset was produced covering the distribution of temperature, humidity and wind for the diurnal cycle. The contribution presents the interpretation of the profiles in respect to stratification of the planetary boundary layer and comparison to the cooperated instruments. An interesting aspect of the observation data is the modification of the wind field by an nearby terrain step which also influences cold air flow near the ground. These observations are compared to mesoscale model data (METRAS and later WRF) in order to check whether the principle mechanisms can be simulated.

Seasonal associations and atmospheric transport distances of Fusarium collected with unmanned aerial vehicles and ground-based sampling devices

NASA Astrophysics Data System (ADS)

Schmale, David; Ross, Shane; Lin, Binbin

2014-05-01

Spores of fungi in the genus Fusarium may be transported through the atmosphere over long distances. Members of this genus are important pathogens and mycotoxin producers. New information is needed to characterize seasonal trends in atmospheric loads of Fusarium and to pinpoint the source(s) of inoculum at both local (farm) and regional (state or country) scales. Spores of Fusarium were collected from the atmosphere in an agricultural ecosystem in Blacksburg, VA, USA using a Burkard volumetric sampler (BVS) 1 m above ground level and autonomous unmanned aerial vehicles (UAVs) 100 m above ground level. More than 2,200 colony forming units (CFUs) of Fusarium were collected during 104 BVS sampling periods and 180 UAV sampling periods over four calendar years (2009-2012). Spore concentrations ranged from 0 to 13 and 0 to 23 spores m-3 for the BVS and the UAVs, respectively. Spore concentrations were generally higher in the fall, spring, and summer, and lower in the winter. Spore concentrations from the BVS were generally higher than those from the UAVs for both seasonal and hourly collections. Some of the species of Fusarium identified from our collections have not been previously reported in the state of Virginia. A Gaussian plume transport model was used to estimate distances to the potential inoculum source(s) by season. This work extends previous studies showing an association between atmospheric transport barriers (Lagrangian coherent structures or LCSs) and the movement of Fusarium in the lower atmosphere. An increased understanding of the aerobiology of Fusarium may contribute to new and improved control strategies for diseases causes by fusaria in the future.

Photovoltaic electric power applied to Unmanned Aerial Vehicles (UAV)

NASA Technical Reports Server (NTRS)

Geis, Jack; Arnold, Jack H.

1994-01-01

Photovoltaic electric-powered flight is receiving a great deal of attention in the context of the United States' Unmanned Aerial Vehicle (UAV) program. This paper addresses some of the enabling technical areas and their potential solutions. Of particular interest are the long-duration, high-altitude class of UAV's whose mission it is to achieve altitudes between 60,000 and 100,000 feet, and to remain at those altitudes for prolonged periods performing various mapping and surveillance activities. Addressed herein are studies which reveal the need for extremely light-weight and efficient solar cells, high-efficiency electric motor-driven propeller modules, and power management and distribution control elements. Since the potential payloads vary dramatically in their power consumption and duty cycles, a typical load profile has been selected to provide commonality for the propulsion power comparisons. Since missions vary widely with respect to ground coverage requirements, from repeated orbiting over a localized target to long-distance routes over irregular terrain, we have also averaged the power requirements for on-board guidance and control power, as well as ground control and communication link utilization. In the context of the national technology reinvestment program, wherever possible we modeled components and materials which have been qualified for space and defense applications, yet are compatible with civilian UAV activities. These include, but are not limited to, solar cell developments, electric storage technology for diurnal operation, local and ground communications, power management and distribution, and control servo design. And finally, the results of tests conducted by Wright Laboratory on ultralight, highly efficient MOCVD GaAs solar cells purchased from EPI Materials Ltd. (EML) of the UK are presented. These cells were also used for modeling the flight characteristics of UAV aircraft.

Sensor-driven area coverage for an autonomous fixed-wing unmanned aerial vehicle.

PubMed

Paull, Liam; Thibault, Carl; Nagaty, Amr; Seto, Mae; Li, Howard

2014-09-01

Area coverage with an onboard sensor is an important task for an unmanned aerial vehicle (UAV) with many applications. Autonomous fixed-wing UAVs are more appropriate for larger scale area surveying since they can cover ground more quickly. However, their non-holonomic dynamics and susceptibility to disturbances make sensor coverage a challenging task. Most previous approaches to area coverage planning are offline and assume that the UAV can follow the planned trajectory exactly. In this paper, this restriction is removed as the aircraft maintains a coverage map based on its actual pose trajectory and makes control decisions based on that map. The aircraft is able to plan paths in situ based on sensor data and an accurate model of the on-board camera used for coverage. An information theoretic approach is used that selects desired headings that maximize the expected information gain over the coverage map. In addition, the branch entropy concept previously developed for autonomous underwater vehicles is extended to UAVs and ensures that the vehicle is able to achieve its global coverage mission. The coverage map over the workspace uses the projective camera model and compares the expected area of the target on the ground and the actual area covered on the ground by each pixel in the image. The camera is mounted on a two-axis gimbal and can either be stabilized or optimized for maximal coverage. Hardware-in-the-loop simulation results and real hardware implementation on a fixed-wing UAV show the effectiveness of the approach. By including the already developed automatic takeoff and landing capabilities, we now have a fully automated and robust platform for performing aerial imagery surveys.

Integrated orbital servicing and payloads study. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1975-01-01

A study is summarized in which a comparison was made of the following modes of maintaining a satellite system: (1) expendable mode in which failed satellites are replaced, (2) on-orbit servicing where a satellite can be fixed by unmanned module exchange in space, and (3) ground refurbishment in which the satellite is brought back to ground for repairs. It was concluded that on-orbit maintenance is the most cost-effective mode and that it is technically feasible. It can be used to repair failed satellites, to improve reliability of operating satellites, and to update equipment. On-orbit servicing can increase program flexibility and satellite reliability, lifetime, and availability. The significant conclusions and results of two studies are summarized.

Ground-Based Sense and Avoid: Enabling Local Area Integration of Unmanned Aircraft Systems into the National Airspace System

DTIC Science & Technology

2015-12-30

and GBOs agreed that when faced with these intruders, successful maintenance of the self‐ separation standard would be beyond the capability of any  SAA ...system. It is important to note that an  SAA  system itself cannot necessarily avoid more maneuverable and potentially hostile intruders that can  in...GBSAA system is likely to be safe  and effective in supporting the  SAA  function in a real‐life deployment.  This performance supports the  operators

Photogrammetry with an Unmanned Aerial System to Assess Body Condition and Growth of Blainville’s Beaked Whales

DTIC Science & Technology

2015-09-30

metrics for key age/ sex classes: 1) Width profiles for adult females, specifically comparing those with (lactating) and without dependent young...hexacopter using remote controls at a height 3 of ~100ft, aided by live video output from the hexacopter that will be monitored on a portable ground unit...Blainville’s beaked whales can be readily assigned to age/ sex classes from photographs of dentition and scarring (Claridge 2013), enabling us to link

Improving the Future of the Army’s Future Combat Systems Program

DTIC Science & Technology

2009-06-01

that the Army will not be able to afford to focus on both its needs in Iraq and Afghanistan and its long-term vision of the future as if they were...and conventional fights. ‘After receiving situational awareness reports from the FCS network, the NLOS-C will be able to put precision fires on...defuse mines. 17 • Small Unmanned Ground Vehicle (SUGV), which is a lightweight robot designed to be man-portable and to be able to scout ahead of

Small Business Innovations

NASA Technical Reports Server (NTRS)

1995-01-01

The PER-Force Handcontroller was originally developed for the International Space Station under a Johnson Space Center Small Business Innovation Research (SBIR) contract. Produced by Cybernet Systems Corporation, the unit is a force-reflecting system that manipulates robots or objects by "feel." The Handcontroller moves in six degrees of freedom, with real and virtual reality forces simulated by a 3-D molecular modeling software package. It is used in molecular modeling in metallurgy applications, satellite docking research, and in research on military unmanned ground vehicles.

A Bird’s Eye View: Development of an Operational ARM Unmanned Aerial Capability for Atmospheric Research in Arctic Alaska

DOE Office of Scientific and Technical Information (OSTI.GOV)

de Boer, Gijs; Ivey, Mark; Schmid, Beat

Here, we present that unmanned aerial capabilities offer exciting new perspectives on the Arctic atmosphere and the US Department of Energy is working with partners to offer such perspectives to the research community. Thorough understanding of aerosols, clouds, boundary layer structure and radiation is required to improve representation of the Arctic atmosphere in weather forecasting and climate models. To develop such understanding, new perspectives are needed to provide details on the vertical structure and spatial variability of key atmospheric properties, along with information over difficult-to-reach surfaces such as newly-forming sea ice. Over the last three years, the US Department ofmore » Energy (DOE) has supported various flight campaigns using unmanned aircraft systems (UAS, also known as UAVs and drones) and tethered balloon systems (TBS) at Oliktok Point, Alaska. These activities have featured in-situ measurements of thermodynamic state, turbulence, radiation, aerosol properties, cloud microphysics and turbulent fluxes to provide a detailed characterization of the lower atmosphere. Alongside a suite of active and passive ground-based sensors and radiosondes deployed by the DOE Atmospheric Radiation Measurement (ARM) program through the third ARM Mobile Facility (AMF-3), these flight activities demonstrate the ability of such platforms to provide critically-needed information. In addition to providing new and unique datasets, lessons learned during initial campaigns have assisted toward the development of an exciting new community resource.« less

The potential of small unmanned aircraft systems and structure-from-motion for topographic surveys: A test of emerging integrated approaches at Cwm Idwal, North Wales

NASA Astrophysics Data System (ADS)

Tonkin, T. N.; Midgley, N. G.; Graham, D. J.; Labadz, J. C.

2014-12-01

Novel topographic survey methods that integrate both structure-from-motion (SfM) photogrammetry and small unmanned aircraft systems (sUAS) are a rapidly evolving investigative technique. Due to the diverse range of survey configurations available and the infancy of these new methods, further research is required. Here, the accuracy, precision and potential applications of this approach are investigated. A total of 543 images of the Cwm Idwal moraine-mound complex were captured from a light (< 5 kg) semi-autonomous multi-rotor unmanned aircraft system using a consumer-grade 18 MP compact digital camera. The images were used to produce a DSM (digital surface model) of the moraines. The DSM is in good agreement with 7761 total station survey points providing a total vertical RMSE value of 0.517 m and vertical RMSE values as low as 0.200 m for less densely vegetated areas of the DSM. High-precision topographic data can be acquired rapidly using this technique with the resulting DSMs and orthorectified aerial imagery at sub-decimetre resolutions. Positional errors on the total station dataset, vegetation and steep terrain are identified as the causes of vertical disagreement. Whilst this aerial survey approach is advocated for use in a range of geomorphological settings, care must be taken to ensure that adequate ground control is applied to give a high degree of accuracy.

Lighter-Than-Air (LTA) "AirStation": Unmanned Aircraft System (UAS) Carrier Concept

NASA Technical Reports Server (NTRS)

Hochstetler, Ronald D.; Bosma, John; Chachad, Girish H.; Blanken, Matthew L.

2016-01-01

The advantages of utilizing an airship as an airborne carrier for support and deployment of Unmanned Aircraft Systems (UAS) are examined. Whether as a stand-alone platform or in concert with conventional aircraft, the airship UAS carrier provides a number of compelling benefits for both military and civilian missions. As a mobile base it can remain operational despite political fallout that may render ground or ocean based UAS sites unavailable. It offers the psychological impact of a power projection tool that has few geographical limits, and holds promise as a new method for cost-saving intelligence gathering. It is also adaptable for civilian variants for supporting: emergency response, security/surveillance, delivery of medical/food supplies, as well as commercial package delivery to metropolitan and remote communities. This paper presents the background on airship-aircraft operations, and explores the general airship carrier concept. Additionally, a catalog of contemporary technologies available to support the airship carrier concept are discussed, and essential elements for an Air-Station Development program proposed.

Live Aircraft Encounter Visualization at FutureFlight Central

NASA Technical Reports Server (NTRS)

Murphy, James R.; Chinn, Fay; Monheim, Spencer; Otto, Neil; Kato, Kenji; Archdeacon, John

2018-01-01

Researchers at the National Aeronautics and Space Administration (NASA) have developed an aircraft data streaming capability that can be used to visualize live aircraft in near real-time. During a joint Federal Aviation Administration (FAA)/NASA Airborne Collision Avoidance System flight series, test sorties between unmanned aircraft and manned intruder aircraft were shown in real-time at NASA Ames' FutureFlight Central tower facility as a virtual representation of the encounter. This capability leveraged existing live surveillance, video, and audio data streams distributed through a Live, Virtual, Constructive test environment, then depicted the encounter from the point of view of any aircraft in the system showing the proximity of the other aircraft. For the demonstration, position report data were sent to the ground from on-board sensors on the unmanned aircraft. The point of view can be change dynamically, allowing encounters from all angles to be observed. Visualizing the encounters in real-time provides a safe and effective method for observation of live flight testing and a strong alternative to travel to the remote test range.

Ad Hoc Networking for Unmanned Ground Vehicles: Design and Evaluation at Command, Control, Communications, Intelligence, Surveillance and Reconnaissance On-the-Move

DTIC Science & Technology

2006-11-01

software components used in the ad hoc nodes for the C4ISR OTM experiment were OLSRD, an open-source proactive MANET routing software, and OpenVPN , an...developed by Mike Baker (openwrt.org). 6OpenVPN is a trademark of OpenVPN Solutions LLC. 6 Secure communications in the MANET are achieved with...encryption provided by Wired Equivalent Privacy (WEP) and OpenVPN . The WEP protocol, which is part of the IEEE 802.11 wireless networking standard

Advanced Mobility Testbed for Dynamic Semi-Autonomous Unmanned Ground Vehicles

DTIC Science & Technology

2015-04-24

constraint, effectively hiding them from the dynamics solver. Thus the resulting system topology is once again a tree with only inter-body hinges and...the geometry of wheel sinkage (left) and stress distribution under the wheel (right) from reference [24]. With τmax(θ) = c+σ(θ) tan (φ). the shear...sliding). The transversal deflection α or lateral slip angle and the lateral slip coefficient Sα are Sα = tan (α) = −vy vx (12) The comprehensive slip ratio

An Interactive, Physics-Based Unmanned Ground Vehicle Simulator Leveraging Open Source Gaming Technology: Progress in the Development and Application of the Virtual Autonomous Navigation Environment (VANE) Desktop

DTIC Science & Technology

2009-01-01

interface, mechatronics, video games 1. INTRODUCTION Engineering methods have substantially and continuously evolved over the past 40 years. In the past...1970s, video games have pioneered interactive simulation and laid the groundwork for inexpensive computing that individuals, corporations, and...purposes. This has not gone unnoticed, and software technology and techniques evolved for video games are beginning to have extraordinary impact in

Autonomous Weapon Systems: A Brief Survey of Developmental, Operational, Legal, and Ethical Issues

DTIC Science & Technology

2015-12-01

aspects of the early days of these ground- based AWS.14 Gage’s account characterizes the efforts as largely focused on research and development in...human judg- ment, but this responsibility also extends to those who design and develop the systems.27 The next section ad- dresses some of the key... develop - ment (R&D) efforts.”31 Further, the report argues that recent development of unmanned systems was large- ly evolutionary, moving forward based on

Synthesis of the unmanned aerial vehicle remote control augmentation system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomczyk, Andrzej, E-mail: A.Tomczyk@prz.edu.pl

Medium size Unmanned Aerial Vehicle (UAV) usually flies as an autonomous aircraft including automatic take-off and landing phases. However in the case of the on-board control system failure, the remote steering is using as an emergency procedure. In this reason, remote manual control of unmanned aerial vehicle is used more often during take-of and landing phases. Depends on UAV take-off mass and speed (total energy) the potential crash can be very danger for airplane and environment. So, handling qualities of UAV is important from pilot-operator point of view. In many cases the dynamic properties of remote controlling UAV are notmore » suitable for obtaining the desired properties of the handling qualities. In this case the control augmentation system (CAS) should be applied. Because the potential failure of the on-board control system, the better solution is that the CAS algorithms are placed on the ground station computers. The method of UAV handling qualities shaping in the case of basic control system failure is presented in this paper. The main idea of this method is that UAV reaction on the operator steering signals should be similar - almost the same - as reaction of the 'ideal' remote control aircraft. The model following method was used for controller parameters calculations. The numerical example concerns the medium size MP-02A UAV applied as an aerial observer system.« less

Uav-Mapping - a User Report

NASA Astrophysics Data System (ADS)

Mayr, W.

2011-09-01

This paper reports on first hand experiences in operating an unmanned airborne system (UAS) for mapping purposes in the environment of a mapping company. Recently, a multitude of activities in UAVs is visible, and there is growing interest in the commercial, industrial, and academic mapping user communities and not only in those. As an introduction, the major components of an UAS are identified. The paper focuses on a 1.1kg UAV which is integrated and gets applied on a day-to-day basis as part of an UAS in standard aerial imaging tasks for more than two years already. We present the unmanned airborne vehicle in some detail as well as the overall system components such as autopilot, ground station, flight mission planning and control, and first level image processing. The paper continues with reporting on experiences gained in setting up constraints such a system needs to fulfill. Further on, operational aspects with emphasis on unattended flight mission mode are presented. Various examples show the applicability of UAS in geospatial tasks, proofing that UAS are capable delivering reliably e.g. orthomosaics, digital surface models and more. Some remarks on achieved accuracies give an idea on obtainable qualities. A discussion about safety features puts some light on important matters when entering unmanned flying activities and rounds up this paper. Conclusions summarize the state of the art of an operational UAS from the point of the view of the author.

Migration strategies for service-enabling ground control stations for unmanned systems

NASA Astrophysics Data System (ADS)

Kroculick, Joseph B.

2011-06-01

Future unmanned systems will be integrated into the Global Information Grid (GIG) and support net-centric data sharing, where information in a domain is exposed to a wide variety of GIG stakeholders that can make use of the information provided. Adopting a Service-Oriented Architecture (SOA) approach to package reusable UAV control station functionality into common control services provides a number of benefits including enabling dynamic plug and play of components depending on changing mission requirements, supporting information sharing to the enterprise, and integrating information from authoritative sources such as mission planners with the UAV control stations data model. It also allows the wider enterprise community to use the services provided by unmanned systems and improve data quality to support more effective decision-making. We explore current challenges in migrating UAV control systems that manage multiple types of vehicles to a Service-Oriented Architecture (SOA). Service-oriented analysis involves reviewing legacy systems and determining which components can be made into a service. Existing UAV control stations provide audio/visual, navigation, and vehicle health and status information that are useful to C4I systems. However, many were designed to be closed systems with proprietary software and hardware implementations, message formats, and specific mission requirements. An architecture analysis can be performed that reviews legacy systems and determines which components can be made into a service. A phased SOA adoption approach can then be developed that improves system interoperability.

Three-Dimensional Digital Documentation of Heritage Sites Using Terrestrial Laser Scanning and Unmanned Aerial Vehicle Photogrammetry

NASA Astrophysics Data System (ADS)

Jo, Y. H.; Kim, J. Y.

2017-08-01

Three-dimensional digital documentation is an important technique for the maintenance and monitoring of cultural heritage sites. This study focuses on the three-dimensional digital documentation of the Magoksa Temple, Republic of Korea, using a combination of terrestrial laser scanning and unmanned aerial vehicle (UAV) photogrammetry. Terrestrial laser scanning mostly acquired the vertical geometry of the buildings. In addition, the digital orthoimage produced by UAV photogrammetry had higher horizontal data acquisition rate than that produced by terrestrial laser scanning. Thus, the scanning and UAV photogrammetry were merged by matching 20 corresponding points and an absolute coordinate system was established using seven ground control points. The final, complete threedimensional shape had perfect horizontal and vertical geometries. This study demonstrates the potential of integrating terrestrial laser scanning and UAV photogrammetry for three-dimensional digital documentation. This new technique is expected to contribute to the three-dimensional digital documentation and spatial analysis of cultural heritage sites.

Employing unmanned aerial vehicle to monitor the health condition of wind turbines

NASA Astrophysics Data System (ADS)

Huang, Yishuo; Chiang, Chih-Hung; Hsu, Keng-Tsang; Cheng, Chia-Chi

2018-04-01

Unmanned aerial vehicle (UAV) can gather the spatial information of huge structures, such as wind turbines, that can be difficult to obtain with traditional approaches. In this paper, the UAV used in the experiments is equipped with high resolution camera and thermal infrared camera. The high resolution camera can provide a series of images with resolution up to 10 Megapixels. Those images can be used to form the 3D model using the digital photogrammetry technique. By comparing the 3D scenes of the same wind turbine at different times, possible displacement of the supporting tower of the wind turbine, caused by ground movement or foundation deterioration may be determined. The recorded thermal images are analyzed by applying the image segmentation methods to the surface temperature distribution. A series of sub-regions are separated by the differences of the surface temperature. The high-resolution optical image and the segmented thermal image are fused such that the surface anomalies are more easily identified for wind turbines.

Generation and Assessment of High Resolution Digital Surface Model by Using Unmanned Air Vehicle Based Multicopter

NASA Astrophysics Data System (ADS)

Gülci, S.; Dindaroğlu, T.; Gündoğan, R.

2017-11-01

Unmanned air vehicle systems (UAVSs), which are presently defined as effective measuring instruments, can be used for measurements and evaluation studies in fields. Furthermore, UAVs are effective tools that can produce high-precision and resolution data for use in geographic information system-based work. This study examined a multicopter (hexacopter) as an air platform to seek opportunity in generating DSM with high resolution. Flights were performed in Kahramanmaras Sutcu Imam University Campus area in Turkey. Pre-assessment of field works, mission, tests and installation were prepared by using a Laptop with an adaptive ground control station. Hand remote controller unit was also linked and activated during flight to interfere with emergency situations. Canon model IXSUS 160 was preferred as sensor. As a result of this study, as mentioned previous studies, .The orthophotos can be produced by RGB (Red-green-blue) images obtained with UAV, herewith information on terrain topography, land cover and soil erosion can be evaluated.

Estimating plant distance in maize using Unmanned Aerial Vehicle (UAV).

PubMed

Zhang, Jinshui; Basso, Bruno; Price, Richard F; Putman, Gregory; Shuai, Guanyuan

2018-01-01

Distance between rows and plants are essential parameters that affect the final grain yield in row crops. This paper presents the results of research intended to develop a novel method to quantify the distance between maize plants at field scale using an Unmanned Aerial Vehicle (UAV). Using this method, we can recognize maize plants as objects and calculate the distance between plants. We initially developed our method by training an algorithm in an indoor facility with plastic corn plants. Then, the method was scaled up and tested in a farmer's field with maize plant spacing that exhibited natural variation. The results of this study demonstrate that it is possible to precisely quantify the distance between maize plants. We found that accuracy of the measurement of the distance between maize plants depended on the height above ground level at which UAV imagery was taken. This study provides an innovative approach to quantify plant-to-plant variability and, thereby final crop yield estimates.

A Bird’s Eye View: Development of an Operational ARM Unmanned Aerial Capability for Atmospheric Research in Arctic Alaska

DOE PAGES

de Boer, Gijs; Ivey, Mark; Schmid, Beat; ...

2018-03-14

Here, we present that unmanned aerial capabilities offer exciting new perspectives on the Arctic atmosphere and the US Department of Energy is working with partners to offer such perspectives to the research community. Thorough understanding of aerosols, clouds, boundary layer structure and radiation is required to improve representation of the Arctic atmosphere in weather forecasting and climate models. To develop such understanding, new perspectives are needed to provide details on the vertical structure and spatial variability of key atmospheric properties, along with information over difficult-to-reach surfaces such as newly-forming sea ice. Over the last three years, the US Department ofmore » Energy (DOE) has supported various flight campaigns using unmanned aircraft systems (UAS, also known as UAVs and drones) and tethered balloon systems (TBS) at Oliktok Point, Alaska. These activities have featured in-situ measurements of thermodynamic state, turbulence, radiation, aerosol properties, cloud microphysics and turbulent fluxes to provide a detailed characterization of the lower atmosphere. Alongside a suite of active and passive ground-based sensors and radiosondes deployed by the DOE Atmospheric Radiation Measurement (ARM) program through the third ARM Mobile Facility (AMF-3), these flight activities demonstrate the ability of such platforms to provide critically-needed information. In addition to providing new and unique datasets, lessons learned during initial campaigns have assisted toward the development of an exciting new community resource.« less

Using unmanned aerial vehicles and structure-from-motion photogrammetry to characterize sedimentary outcrops: An example from the Morrison Formation, Utah, USA

NASA Astrophysics Data System (ADS)

Chesley, J. T.; Leier, A. L.; White, S.; Torres, R.

2017-06-01

Recently developed data collection techniques allow for improved characterization of sedimentary outcrops. Here, we outline a workflow that utilizes unmanned aerial vehicles (UAV) and structure-from-motion (SfM) photogrammetry to produce sub-meter-scale outcrop reconstructions in 3-D. SfM photogrammetry uses multiple overlapping images and an image-based terrain extraction algorithm to reconstruct the location of individual points from the photographs in 3-D space. The results of this technique can be used to construct point clouds, orthomosaics, and digital surface models that can be imported into GIS and related software for further study. The accuracy of the reconstructed outcrops, with respect to an absolute framework, is improved with geotagged images or independently gathered ground control points, and the internal accuracy of 3-D reconstructions is sufficient for sub-meter scale measurements. We demonstrate this approach with a case study from central Utah, USA, where UAV-SfM data can help delineate complex features within Jurassic fluvial sandstones.

A robust nonlinear skid-steering control design applied to the MULE (6x6) unmanned ground vehicle

NASA Astrophysics Data System (ADS)

Kaloust, Joseph

2006-05-01

The paper presents a robust nonlinear skid-steering control design concept. The control concept is based on the recursive/backstepping control design technique and is capable of compensating for uncertainties associated with sensor noise measurements and/or system dynamic state uncertainties. The objective of this control design is to demonstrate the performance of the nonlinear controller under uncertainty associate with road traction (rough off-road and on-road terrain). The MULE vehicle is used in the simulation modeling and results.

Validation of Underwater Sensor Package Using Feature Based SLAM

PubMed Central

Cain, Christopher; Leonessa, Alexander

2016-01-01

Robotic vehicles working in new, unexplored environments must be able to locate themselves in the environment while constructing a picture of the objects in the environment that could act as obstacles that would prevent the vehicles from completing their desired tasks. In enclosed environments, underwater range sensors based off of acoustics suffer performance issues due to reflections. Additionally, their relatively high cost make them less than ideal for usage on low cost vehicles designed to be used underwater. In this paper we propose a sensor package composed of a downward facing camera, which is used to perform feature tracking based visual odometry, and a custom vision-based two dimensional rangefinder that can be used on low cost underwater unmanned vehicles. In order to examine the performance of this sensor package in a SLAM framework, experimental tests are performed using an unmanned ground vehicle and two feature based SLAM algorithms, the extended Kalman filter based approach and the Rao-Blackwellized, particle filter based approach, to validate the sensor package. PMID:26999142

Fast Sparse Coding for Range Data Denoising with Sparse Ridges Constraint

PubMed Central

Lao, Mingjie; Sang, Yongsheng; Wen, Fei; Zhai, Ruifang

2018-01-01

Light detection and ranging (LiDAR) sensors have been widely deployed on intelligent systems such as unmanned ground vehicles (UGVs) and unmanned aerial vehicles (UAVs) to perform localization, obstacle detection, and navigation tasks. Thus, research into range data processing with competitive performance in terms of both accuracy and efficiency has attracted increasing attention. Sparse coding has revolutionized signal processing and led to state-of-the-art performance in a variety of applications. However, dictionary learning, which plays the central role in sparse coding techniques, is computationally demanding, resulting in its limited applicability in real-time systems. In this study, we propose sparse coding algorithms with a fixed pre-learned ridge dictionary to realize range data denoising via leveraging the regularity of laser range measurements in man-made environments. Experiments on both synthesized data and real data demonstrate that our method obtains accuracy comparable to that of sophisticated sparse coding methods, but with much higher computational efficiency. PMID:29734793

DDDAMS-based Urban Surveillance and Crowd Control via UAVs and UGVs

DTIC Science & Technology

2015-12-04

for crowd dynamics modeling by incorporating multi-resolution data, where a grid-based method is used to model crowd motion with UAVs’ low -resolution...information and more computational intensive (and time-consuming). Given that the deployment of fidelity selection results in simulation faces computational... low fidelity information FOV y (A) DR x (A) DR y (A) Not detected high fidelity information Table 1: Parameters for UAV and UGV for their detection

UGV Control Interoperability Profile (IOP), Version 0

DTIC Science & Technology

2011-12-21

task or function associated with the ID (e.g. “select asset gear” and “switch between local and zulu time display”). Category Provides a high...CTRL- Basic Status-2 view Zulu date and time in Date-Time-Group (DTG) format Basic Status S SWP Icon (text) CTRL- Basic Status-3 switch...between local and zulu time display Basic Status C SW1 CTRL- Basic Status-4 view unique identifier/call sign for each asset Basic Status S

ALADINA - an unmanned research aircraft for observing vertical and horizontal distributions of ultrafine particles within the atmospheric boundary layer

NASA Astrophysics Data System (ADS)

Altstädter, B.; Platis, A.; Wehner, B.; Scholtz, A.; Lampert, A.; Wildmann, N.; Hermann, M.; Käthner, R.; Bange, J.; Baars, H.

2014-12-01

This paper presents the unmanned research aircraft Carolo P360 "ALADINA" (Application of Light-weight Aircraft for Detecting IN-situ Aerosol) for investigating the horizontal and vertical distribution of ultrafine particles in the atmospheric boundary layer (ABL). It has a wingspan of 3.6 m, a maximum take-off weight of 25 kg and is equipped with aerosol instrumentation and meteorological sensors. A first application of the system, together with the unmanned research aircraft MASC (Multi-Purpose Airborne Carrier) of the Eberhard-Karls University of Tübingen (EKUT), is described. As small payload for ALADINA, two condensation particle counters (CPC) and one optical particle counter (OPC) were miniaturized by re-arranging the vital parts and composing them in a space saving way in the front compartment of the airframe. The CPCs are improved concerning the lower detection threshold and the response time. Each system was characterized in the laboratory and calibrated with test aerosols. The CPCs are operated with two different lower detection threshold diameters of 6 and 18 nm. The amount of ultrafine particles, which is an indicator for new particle formation, is derived from the difference in number concentrations of the two CPCs. Turbulence and thermodynamic structure of the boundary layer are described by measurements of fast meteorological sensors that are mounted at the aircraft nose. A first demonstration of ALADINA and a feasibility study were conducted in Melpitz near Leipzig, Germany, at the Global Atmosphere Watch (GAW) station of the Leibniz Institute for Tropospheric Research (TROPOS) on two days in October 2013. There, various ground-based instruments are installed for long-term atmospheric monitoring. The ground-based infrastructure provides valuable additional background information to embed the flights in the continuous atmospheric context and is used for validation of the airborne results. The development of the boundary layer, derived from backscatter signals of a portable Raman lidar POLLYXT, allows a quick overview of the current vertical structure of atmospheric particles. Ground-based aerosol number concentrations are consistent with the results from flights in heights of a few meters. In addition, a direct comparison of ALADINA aerosol data and ground-based aerosol data, sampling the air at the same location, shows comparable values. MASC was operated simultaneously with complementary flight patterns. It is equipped with the same meteorological instruments that offer the possibility to determine turbulent fluxes. Therefore additional information about meteorological conditions was collected in the lowest part of the atmosphere. Vertical profiles up to 1000 m altitude indicate a high variability with distinct layers of aerosol especially for the small particles of a few nanometers in diameter. Particle bursts were observed on one day during the boundary layer development in the morning.

Accelerating the Kill Chain via Future Unmanned Aircraft

DTIC Science & Technology

2007-04-01

Controller JTRS Joint Tactical Radio System Lasercom Laser communications LDHD Low Density High Demand LEO Low Earth Orbit LGB Laser Guided Bomb...published the Unmanned Aircraft Systems Roadmap 2005 that included the terms Unmanned Aircraft System (UAS) and Unmanned Aircraft (UA). This...comprehensive publication used the term Unmanned Aircraft Systems when referring to the entire system and the term Unmanned Aircraft when referring only to the

Ice nucleating particles over the Eastern Mediterranean measured at ground and by unmanned aircraft systems

NASA Astrophysics Data System (ADS)

Weber, Daniel; Schrod, Jann; Drücke, Jaqueline; Keleshis, Christos; Pikridas, Michael; Ebert, Martin; Cvetkovic, Bojan; Nickovic, Slobodan; Baars, Holger; Marinou, Eleni; Vrekoussis, Mihalis; Sciare, Jean; Mihalopoulos, Nikos; Curtius, Joachim; Bingemer, Heinz G.

2017-04-01

During the intensive INUIT-BACCHUS-ACTRIS field campaign focusing on aerosols, clouds and ice nucleation in the Eastern Mediterranean in April 2016, we have measured the abundance of ice nucleating particles (INP) in the lower troposphere both with unmanned aircraft systems (UAS) as well as from the ground. Aerosol samples were collected by miniaturized electrostatic precipitators onboard the UAS and were analyzed immediately after collection on site in the ice nucleus counter FRIDGE for INP active at -20˚ C to -30˚ C in the deposition/condensation mode (INPD). Immersion freezing INP (INPI) were sampled on membrane filters and were analysed in aqueous extracts by the drop freezing method on the cold stage of FRIDGE. Ground samples were collected at the Cyprus Atmospheric Observatory (CAO) in Agia Marina Xyliatou (Latitude; 35˚ 2' 8" N; Longitude: 33˚ 3' 26" E; Altitude: 532 m a.s.l.). During the one-month campaign, we encountered a series of Saharan dust plumes that traveled at several kilometers altitude. Here we present INP data from 42 individual flights, together with OPC aerosol number concentrations, backscatter and depolarization retrievals from the Polly-XT Raman Lidar, dust concentrations derived by the dust transport model DREAM (Dust Regional Atmospheric Model), and results from scanning electron microscopy. The effect of the dust plumes is reflected by the coincidence of INP with the particulate mass (PM), the Lidar retrievals and the predicted dust mass of the model. This suggests that mineral dust or a constituent related to dust was a major contributor to the ice nucleating properties of the aerosol. Peak concentrations of above 100 INP std.l-1 were measured at -30˚ C. The INPD concentration in elevated plumes was on average a factor of 10 higher than at ground level. The INPI concentration at ground also agreed with PM levels and exceeded the ground-based INPD concentration by more than one order of magnitude. Since desert dust is transported for long distances over wide areas of the globe predominantly at several km altitude, we conclude that INP measurements at ground level may be of limited significance for the situation at the level of cloud formation. This project received funding from the European Union's Seventh Framework Programme (FP7) project BACCHUS under grant agreement no. 603445, and the European Union's Horizon 2020 research and innovation programme ACTRIS-2 under grant agreement No 654109, and the Deutsche Forschungsgemeinschaft (DFG) under the Research Unit FOR 1525 (INUIT).

Cyber Safety and Security for Reduced Crew Operations (RCO)

NASA Technical Reports Server (NTRS)

Driscoll, Kevin R.; Roy, Aloke; Ponchak, Denise S.; Downey, Alan N.

2017-01-01

NASA and the Aviation Industry is looking into reduced crew operations (RCO) that would cut today's required two-person flight crews down to a single pilot with support from ground-based crews. Shared responsibility across air and ground personnel will require highly reliable and secure data communication and supporting automation, which will be safety-critical for passenger and cargo aircraft. This paper looks at the different types and degrees of authority delegation given from the air to the ground and the ramifications of each, including the safety and security hazards introduced, the mitigation mechanisms for these hazards, and other demands on an RCO system architecture which would be highly invasive into (almost) all safety-critical avionics. The adjacent fields of unmanned aerial systems and autonomous ground vehicles are viewed to find problems that RCO may face and related aviation accident scenarios are described. The paper explores possible data communication architectures to meet stringent performance and information security (INFOSEC) requirements of RCO. Subsequently, potential challenges for RCO data communication authentication, encryption and non-repudiation are identified.

Development and Integration of a Solar Powered Unmanned Aerial Vehicle and a Wireless Sensor Network to Monitor Greenhouse Gases

PubMed Central

Malaver, Alexander; Motta, Nunzio; Corke, Peter; Gonzalez, Felipe

2015-01-01

Measuring gases for environmental monitoring is a demanding task that requires long periods of observation and large numbers of sensors. Wireless Sensor Networks (WSNs) and Unmanned Aerial Vehicles (UAVs) currently represent the best alternative to monitor large, remote, and difficult access areas, as these technologies have the possibility of carrying specialized gas sensing systems. This paper presents the development and integration of a WSN and an UAV powered by solar energy in order to enhance their functionality and broader their applications. A gas sensing system implementing nanostructured metal oxide (MOX) and non-dispersive infrared sensors was developed to measure concentrations of CH4 and CO2. Laboratory, bench and field testing results demonstrate the capability of UAV to capture, analyze and geo-locate a gas sample during flight operations. The field testing integrated ground sensor nodes and the UAV to measure CO2 concentration at ground and low aerial altitudes, simultaneously. Data collected during the mission was transmitted in real time to a central node for analysis and 3D mapping of the target gas. The results highlights the accomplishment of the first flight mission of a solar powered UAV equipped with a CO2 sensing system integrated with a WSN. The system provides an effective 3D monitoring and can be used in a wide range of environmental applications such as agriculture, bushfires, mining studies, zoology and botanical studies using a ubiquitous low cost technology. PMID:25679312

Unmanned Aerial Vehicle Systems for Disaster Relief: Tornado Alley

NASA Technical Reports Server (NTRS)

DeBusk, Wesley M.

2009-01-01

Unmanned aerial vehicle systems are currently in limited use for public service missions worldwide. Development of civil unmanned technology in the United States currently lags behind military unmanned technology development in part because of unresolved regulatory and technological issues. Civil unmanned aerial vehicle systems have potential to augment disaster relief and emergency response efforts. Optimal design of aerial systems for such applications will lead to unmanned vehicles which provide maximum potentiality for relief and emergency response while accounting for public safety concerns and regulatory requirements. A case study is presented that demonstrates application of a civil unmanned system to a disaster relief mission with the intent on saving lives. The concept utilizes unmanned aircraft to obtain advanced warning and damage assessments for tornados and severe thunderstorms. Overview of a tornado watch mission architecture as well as commentary on risk, cost, need for, and design tradeoffs for unmanned aerial systems are provided.

Mapping snow depth distribution in forested terrain using unmanned aerial vehicles and structure-from-motion

NASA Astrophysics Data System (ADS)

Webster, C.; Bühler, Y.; Schirmer, M.; Stoffel, A.; Giulia, M.; Jonas, T.

2017-12-01

Snow depth distribution in forests exhibits strong spatial heterogeneity compared to adjacent open sites. Measurement of snow depths in forests is currently limited to a) manual point measurements, which are sparse and time-intensive, b) ground-penetrating radar surveys, which have limited spatial coverage, or c) airborne LiDAR acquisition, which are expensive and may deteriorate in denser forests. We present the application of unmanned aerial vehicles in combination with structure-from-motion (SfM) methods to photogrammetrically map snow depth distribution in forested terrain. Two separate flights were carried out 10 days apart across a heterogeneous forested area of 900 x 500 m. Corresponding snow depth maps were derived using both, LiDAR-based and SfM-based DTM data, obtained during snow-off conditions. Manual measurements collected following each flight were used to validate the snow depth maps. Snow depths were resolved at 5cm resolution and forest snow depth distribution structures such as tree wells and other areas of preferential melt were represented well. Differential snow depth maps showed maximum ablation in the exposed south sides of trees and smaller differences in the centre of gaps and on the north side of trees. This new application of SfM to map snow depth distribution in forests demonstrates a straightforward method for obtaining information that was previously only available through manual spatially limited ground-based measurements. These methods could therefore be extended to more frequent observation of snow depths in forests as well as estimating snow accumulation and depletion rates.

Virtualizing Super-Computation On-Board Uas

NASA Astrophysics Data System (ADS)

Salami, E.; Soler, J. A.; Cuadrado, R.; Barrado, C.; Pastor, E.

2015-04-01

Unmanned aerial systems (UAS, also known as UAV, RPAS or drones) have a great potential to support a wide variety of aerial remote sensing applications. Most UAS work by acquiring data using on-board sensors for later post-processing. Some require the data gathered to be downlinked to the ground in real-time. However, depending on the volume of data and the cost of the communications, this later option is not sustainable in the long term. This paper develops the concept of virtualizing super-computation on-board UAS, as a method to ease the operation by facilitating the downlink of high-level information products instead of raw data. Exploiting recent developments in miniaturized multi-core devices is the way to speed-up on-board computation. This hardware shall satisfy size, power and weight constraints. Several technologies are appearing with promising results for high performance computing on unmanned platforms, such as the 36 cores of the TILE-Gx36 by Tilera (now EZchip) or the 64 cores of the Epiphany-IV by Adapteva. The strategy for virtualizing super-computation on-board includes the benchmarking for hardware selection, the software architecture and the communications aware design. A parallelization strategy is given for the 36-core TILE-Gx36 for a UAS in a fire mission or in similar target-detection applications. The results are obtained for payload image processing algorithms and determine in real-time the data snapshot to gather and transfer to ground according to the needs of the mission, the processing time, and consumed watts.

Evaluation of Meteorological and Aerosol Sensing with small Unmanned Aerial Systems

NASA Astrophysics Data System (ADS)

Claussen, Johanna; Möhler, Ottmar; Leisner, Thomas; Brooks, Ian; Norris, Sarah; Brooks, Barbara; Hill, Martin; Haunold, Werner; Schrod, Jann; Danielczok, Anja

2013-04-01

Atmospheric aerosols have a large impact on the climate system due to their influence on the global radiation budget. Local aerosol sources such as vegetation, (bare) soil or industrial sites have to be quantified with high resolution data to validate aerosol transport models and improve the input for high resolution weather models. Our goal is to evaluate the use of Unmanned Aerial Systems (UAS) as a method for acquisition of high resolution meteorological and aerosol data. During the INUIT measurement campaign in August 2012 at mount Großer Feldberg near Frankfurt, Germany, several flights with different sensor packages were carried out. We measured basic meteorological parameters such as temperature, relative humidity and air pressure with miniaturized onboard sensors. In addition, the Compact Lightweight Aerosol Spectrometer Probe (CLASP) for aerosol size distribution measurement or the Electrostatic Aerosol Collector (EAC) for aerosol sample collection was installed on board. CLASP measures aerosol particles with diameters from 0.17 μm to 9.5 μm in up to 32 channels at a frequency of 10 Hz. The EAC collects air samples at 2 l/min onto a sample holder. After the flight the ice nuclei on the sample holder are activated and counted in the isothermal static diffusion chamber FRIDGE. The results from the INUIT campaign and additional calibration laboratory measurements show that UAS are a valuable platform for miniaturized sensors. The number of ice nuclei was determined with the EAC at 200m above ground level and compared to the reference measurement on the ground.

Development and integration of a solar powered unmanned aerial vehicle and a wireless sensor network to monitor greenhouse gases.

PubMed

Malaver, Alexander; Motta, Nunzio; Corke, Peter; Gonzalez, Felipe

2015-02-11

Measuring gases for environmental monitoring is a demanding task that requires long periods of observation and large numbers of sensors. Wireless Sensor Networks (WSNs) and Unmanned Aerial Vehicles (UAVs) currently represent the best alternative to monitor large, remote, and difficult access areas, as these technologies have the possibility of carrying specialized gas sensing systems. This paper presents the development and integration of a WSN and an UAV powered by solar energy in order to enhance their functionality and broader their applications. A gas sensing system implementing nanostructured metal oxide (MOX) and non-dispersive infrared sensors was developed to measure concentrations of CH4 and CO2. Laboratory, bench and field testing results demonstrate the capability of UAV to capture, analyze and geo-locate a gas sample during flight operations. The field testing integrated ground sensor nodes and the UAV to measure CO2 concentration at ground and low aerial altitudes, simultaneously. Data collected during the mission was transmitted in real time to a central node for analysis and 3D mapping of the target gas. The results highlights the accomplishment of the first flight mission of a solar powered UAV equipped with a CO2 sensing system integrated with a WSN. The system provides an effective 3D monitoring and can be used in a wide range of environmental applications such as agriculture, bushfires, mining studies, zoology and botanical studies using a ubiquitous low cost technology.

Atmospheric Sampling of Microorganisms with UAS

NASA Astrophysics Data System (ADS)

Schmale, D. G., III

2017-12-01

Many microorganisms relevant to crops, domestic animals, and humans are transported over long distances through the atmosphere. Some of these atmospheric microbes catalyze the freezing of water at higher temperatures and facilitate the onset of precipitation. A few have crossed continents. New technologies are needed to study the movement of microorganisms in the atmosphere. We have used unmanned aircraft systems (UAS) to study the transport of microorganisms tens to hundreds of meters above the ground. These UAS are equipped with unique devices for collecting microbes in the atmosphere during flight. Autonomous systems enable teams of UAS to perform complex atmospheric sampling tasks, and coordinate flight missions with one another. Data collected with UAS can be used to validate and improve disease forecasting models along highways in the sky, connecting transport scales across farms, states, and continents. Though terrestrial environments are often considered a major contributor to atmospheric microbial aerosols, little is known about aquatic sources of microbial aerosols. Droplets containing microorganisms can aerosolize from the water surface, liberating them into the atmosphere. We are using teams of unmanned surface vehicles (USVs) and UAS to study the aerosolization of microbes from aquatic environments. Controlled flume studies using highspeed video have allowed us to observe unique aerosolization phenomena that can launch microbes out of the water and into the air. Unmanned systems may be used to excite the next generation of biologists and engineers, and raise important ethical considerations about the future of human-robot interactions.

An autonomous unmanned aerial vehicle sensing system for structural health monitoring of bridges

NASA Astrophysics Data System (ADS)

Reagan, Daniel; Sabato, Alessandro; Niezrecki, Christopher; Yu, Tzuyang; Wilson, Richard

2016-04-01

As civil infrastructure (i.e. bridges, railways, and tunnels) continues to age; the frequency and need to perform inspection more quickly on a broader scale increases. Traditional inspection and monitoring techniques (e.g., visual inspection, mechanical sounding, rebound hammer, cover meter, electrical potential measurements, ultrasound, and ground penetrating radar) may produce inconsistent results, require lane closure, are labor intensive and time-consuming. Therefore, new structural health monitoring systems must be developed that are automated, highly accurate, minimally invasive, and cost effective. Three-dimensional (3D) digital image correlation (DIC) systems have the merits of extracting full-field strain, deformation, and geometry profiles. These profiles can then be stitched together to generate a complete integrity map of the area of interest. Concurrently, unmanned aerial vehicles (UAVs) have emerged as valuable resources for positioning sensing equipment where it is either difficult to measure or poses a risk to human safety. UAVs have the capability to expedite the optical-based measurement process, offer increased accessibility, and reduce interference with local traffic. Within this work, an autonomous unmanned aerial vehicle in conjunction with 3D DIC was developed for monitoring bridges. The capabilities of the proposed system are demonstrated in both laboratory measurements and data collected from bridges currently in service. Potential measurement influences from platform instability, rotor vibration and positioning inaccuracy are also studied in a controlled environment. The results of these experiments show that the combination of autonomous flight with 3D DIC and other non-contact measurement systems provides a valuable and effective civil inspection platform.

Requirements for an Integrated UAS CNS Architecture

NASA Technical Reports Server (NTRS)

Templin, Fred; Jain, Raj; Sheffield, Greg; Taboso, Pedro; Ponchak, Denise

2017-01-01

The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) is investigating revolutionary and advanced universal, reliable, always available, cyber secure and affordable Communication, Navigation, Surveillance (CNS) options for all altitudes of UAS operations. In Spring 2015, NASA issued a Call for Proposals under NASA Research Announcements (NRA) NNH15ZEA001N, Amendment 7 Subtopic 2.4. Boeing was selected to conduct a study with the objective to determine the most promising candidate technologies for Unmanned Air Systems (UAS) air-to-air and air-to-ground data exchange and analyze their suitability in a post-NextGen NAS environment. The overall objectives are to develop UAS CNS requirements and then develop architectures that satisfy the requirements for UAS in both controlled and uncontrolled air space. This contract is funded under NASAs Aeronautics Research Mission Directorates (ARMD) Aviation Operations and Safety Program (AOSP) Safe Autonomous Systems Operations (SASO) project and proposes technologies for the Unmanned Air Systems Traffic Management (UTM) service. Communications, Navigation and Surveillance (CNS) requirements must be developed in order to establish a CNS architecture supporting Unmanned Air Systems integration in the National Air Space (UAS in the NAS). These requirements must address cybersecurity, future communications, satellite-based navigation APNT, and scalable surveillance and situational awareness. CNS integration, consolidation and miniaturization requirements are also important to support the explosive growth in small UAS deployment. Air Traffic Management (ATM) must also be accommodated to support critical Command and Control (C2) for Air Traffic Controllers (ATC). This document therefore presents UAS CNS requirements that will guide the architecture.

Study of launch site processing and facilities for future launch vehicles

NASA Astrophysics Data System (ADS)

Shaffer, Rex

1995-03-01

The purpose of this research is to provide innovative and creative approaches to assess the impact to the Kennedy Space Center and other launch sites for a range of candidate manned and unmanned space transportation systems. The general scope of the research includes the engineering activities, analyses, and evaluations defined in the four tasks below: (1) development of innovative approaches and computer aided tools; (2) operations analyses of launch vehicle concepts and designs; (3) assessment of ground operations impacts; and (4) development of methodologies to identify promising technologies.

Development of Autonomous Optimal Cooperative Control in Relay Rover Configured Small Unmanned Aerial Systems

DTIC Science & Technology

2013-03-01

Unmanned Aircraft Systems Flight Plan that identified small unmanned aerial systems ( SUAS ) as “a profound technological...advances in small unmanned aerial systems ( SUAS ) cooperative control. The end state objective of the research effort was to flight test an autonomous...requirements were captured in the Unmanned Aircraft Systems Flight Plan . The flight plan

Spacecraft platform cost estimating relationships

NASA Technical Reports Server (NTRS)

Gruhl, W. M.

1972-01-01

The three main cost areas of unmanned satellite development are discussed. The areas are identified as: (1) the spacecraft platform (SCP), (2) the payload or experiments, and (3) the postlaunch ground equipment and operations. The SCP normally accounts for over half of the total project cost and accurate estimates of SCP costs are required early in project planning as a basis for determining total project budget requirements. The development of single formula SCP cost estimating relationships (CER) from readily available data by statistical linear regression analysis is described. The advantages of single formula CER are presented.