Technical and Economic Aspects of Low Emission Reduction in Poland

NASA Astrophysics Data System (ADS)

Dzikuć, M.; Łasiński, K.

2017-12-01

The paper presents the problem of excessive air pollution in Poland caused mainly by low emission. The emission arises in result of heating flats by means of old and energetically inefficient heating installations. In Poland and Bulgaria the inhaled air is of the worst quality out of all EU countries. The paper presents economic and technical problems related to low emission occurring during the combustion of solid fuels in local boiler houses. Furthermore, the most significant economic issues, connected with the reduction of low emission are discussed, as well as technological possibilities of efficient reduction of the amount of pollution in the atmosphere. Conclusions are presented at the end of the article.

A Summary of Research on Energy Saving and Emission Reduction of Transportation

NASA Astrophysics Data System (ADS)

Cheng, Dongxiang; Wu, Lufen

2017-12-01

Road transport is an important part of transportation, and road in the field of energy-saving emission reduction is a very important industry. According to the existing problems of road energy saving and emission reduction, this paper elaborates the domestic and international research on energy saving and emission reduction from three aspects: road network optimization, pavement material and pavement maintenance. Road network optimization may be overlooked, and the research content is still relatively preliminary; pavement materials mainly from the asphalt pavement temperature mixed asphalt technology research; pavement maintenance technology development is relatively comprehensive.

Emissions reduction policies and recent trends in Southern California's ambient air quality.

PubMed

Lurmann, Fred; Avol, Ed; Gilliland, Frank

2015-03-01

To assess accountability and effectiveness of air regulatory policies, we reviewed more than 20 years of monitoring data, emissions estimates, and regulatory policies across several southern California communities participating in a long-term study of children's health. Between 1994 and 2011, air quality improved for NO2 and PM2.5 in virtually all the monitored communities. Average NO2 declined 28% to 53%, and PM2.5 decreased 13% to 54%. Year-to-year PM2.5 variability at lower pollution sites was large compared to changes in long-term trends. PM10 and O3 decreases were largest in communities that were initially among the most polluted. Trends in annual average NO2, PM2.5, and PM10 concentrations in higher pollution communities were generally consistent with NOx, ROG, SOx, PM2.5, and PM10 emissions decreases. Reductions observed at one of the higher PM2.5 sites, Mira Loma, were generally within the range expected from reductions observed in ROG, NOx, SOx, and PM2.5 emissions. Despite a 38% increase in regional motor vehicle activity, vigorous economic growth, and a 30% population increase, total estimated emissions of NOx, ROG, SOx, PM2.5, and PM10 decreased by 54%, 65%, 40%, 21%, and 15%, respectively, during the 20-year time period. Emission control strategies in California have achieved dramatic reductions in ambient NO2, O3, PM2.5, and PM10. However, additional reductions will still be needed to achieve current health-based clean air standards. For many cities facing the challenge of reducing air pollution to meet health-based standards, the emission control policies and pollution reduction programs adopted in southern California should serve as an example of the potential success of aggressive, comprehensive, and integrated approaches. Policies targeting on-road mobile emissions were the single most important element for observed improvements in the Los Angeles region. However, overall program success was the result of a much broader approach designed to

REDUCTION OF EMISSIONS FROM A HIGH SPEED FERRY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson,G.; Gautam, M; Clark, N

2003-08-24

Emissions from marine vessels are being scrutinized as a major contributor to the total particulate matter (TPM), oxides of sulfur (SOx) and oxides of nitrogen (NOx) environmental loading. Fuel sulfur control is the key to SOx reduction. Significant reductions in the emissions from on-road vehicles have been achieved in the last decade and the emissions from these vehicles will be reduced by another order of magnitude in the next five years: these improvements have served to emphasize the need to reduce emissions from other mobile sources, including off road equipment, locomotives, and marine vessels. Diesel-powered vessels of interest include oceanmore » going vessels with low- and medium-speed engines, as well as ferries with high speed engines, as discussed below. A recent study examined the use of intake water injection (WIS) and ultra low sulfur diesel (ULSD) to reduce the emissions from a high-speed passenger ferry in southern California. One of the four Detroit Diesel 12V92 two-stroke high speed engines that power the Waverider (operated by SCX, inc.) was instrumented to collect intake airflow, fuel flow, shaft torque, and shaft speed. Engine speed and shaft torque were uniquely linked for given vessel draft and prevailing wind and sea conditions. A raw exhaust gas sampling system was utilized to measure the concentration of NOx, carbon dioxide (CO2), and oxygen (O2) and a mini dilution tunnel sampling a slipstream from the raw exhaust was used to collect TPM on 70 mm filters. The emissions data were processed to yield brake-specific mass results. The system that was employed allowed for redundant data to be collected for quality assurance and quality control. To acquire the data, the Waverider was operated at five different steady state speeds. Three modes were in the open sea off Oceanside, CA, and idle and harbor modes were also used. Data have showed that the use of ULSD along with water injection (WIS) could significantly reduce the emissions of NOx

Development of a Comprehensive Community Nitrogen Oxide Emissions Reduction Toolkit (CCNERT)

NASA Astrophysics Data System (ADS)

Sung, Yong Hoon

The main objective of this study is to research and develop a simplified tool to estimate energy use in a community and its associated effects on air pollution. This tool is intended to predict the impacts of selected energy conservation options and efficiency programs on emission reduction. It is intended to help local government and their residents understand and manage information collection and the procedures to be used. This study presents a broad overview of the community-wide energy use and NOx emissions inventory process. It also presents various simplified procedures to estimate each sector's energy use. In an effort to better understand community-wide energy use and its associated NOx emissions, the City of College Station, Texas, was selected as a case study community for this research. While one community might successfully reduce the production of NOx emissions by adopting electricity efficiency programs in its buildings, another community might be equally successful by changing the mix of fuel sources used to generate electricity, which is consumed by the community. In yet a third community low NOx automobiles may be mandated. Unfortunately, the impact and cost of one strategy over another changes over time as major sources of pollution are reduced. Therefore, this research proposes to help community planners answer these questions and to assist local communities with their NOx emission reduction plans by developing a Comprehensive Community NOx Emissions Reduction Toolkit (CCNERT). The proposed simplified tool could have a substantial impact on reducing NOx emission by providing decision-makers with a preliminary understanding about the impacts of various energy efficiency programs on emissions reductions. To help decision makers, this study has addressed these issues by providing a general framework for examining how a community's non-renewable energy use leads to NOx emissions, by quantifying each end-user's energy usage and its associated NOx

Emissions from residential combustion considering end-uses and spatial constraints: Part II, emission reduction scenarios

NASA Astrophysics Data System (ADS)

Winijkul, Ekbordin; Bond, Tami C.

2016-01-01

Cooking, heating, and other activities in the residential sector are major sources of indoor and outdoor air pollution, especially when solid fuels are used to provide energy. Because of their deleterious effects on the atmosphere and human health, multinational strategies to reduce emissions have been proposed. This study examines the effects of some possible policies, considering realistic factors that constrain mitigation: end-uses, spatial constraints involving proximity to forest or electricity, existing technology, and assumptions about user behavior. Reduction scenarios are applied to a year-2010, spatially distributed baseline of emissions of particulate matter, black carbon, organic carbon, nitrogen oxides, methane, non-methane hydrocarbons, carbon monoxide, and carbon dioxide. Scenarios explored are: (1) cleanest current stove, where we assume that existing technology in each land type is applied to burn existing fuels; (2) stove standards, where we assume that stoves are designed to meet performance standards; and (3) clean fuels, where users adopt the cleanest fuels plausible in each land type. We assume that people living in forest access areas continue to use wood regardless of available fuels, so the clean-fuels scenario leads to a reduction in emissions of 18-25%, depending on the pollutant, across the study region. Cleaner stoves preferentially affect land types with forest access, where about half of the fuel is used; emission reductions range from 25 to 82%, depending on the pollutant. If stove performance standards can be met, particulate matter emissions are reduced by 62% for the loosest standards and 95% for the tightest standards, and carbon monoxide is reduced by 40% and 62% for the loosest and tightest standards. Reductions in specific regions and countries depend on the existing fuel mixture and the population division among land types, and are explored for Latin America, Africa, East Asia, South Asia, and Southeast Asia.

A Healthy Reduction in Oil Dependence and Carbon Emissions

NASA Astrophysics Data System (ADS)

Higgins, P. A.; Higgins, M.

2003-12-01

Societal dependence on oil as an energy source for personal transportation leads to increasingly negative social consequences including climate change, air pollution, political and economic instability and habitat degradation. Our heavy reliance on the automobile for transportation, determined in part by urban sprawl, also contributes to the population's increasingly sedentary lifestyle and to a concomitant degradation in health. We have shown that widespread substitution of exercise, commensurate with previously recommended levels, through biking or walking instead of driving can substantially reduce oil consumption and carbon emissions. For example, if all individuals between the ages of 10 and 64 substituted one hour of cycling for driving the reduction in gasoline demand would be equivalent to the gas produced from 34.9 percent of current oil consumption. Relative to 1990 net US emissions, this constitutes a 10.9 percent reduction in carbon emissions. Therefore, substitution of exercise for driving could improve health, reduce carbon emissions and save more oil than even upper estimates of that contained in the Arctic National Wildlife Refuge.

Unexpected slowdown of US pollutant emission reduction in the past decade

PubMed Central

McDonald, Brian C.; Worden, Helen; Worden, John R.; Miyazaki, Kazuyuki; Qu, Zhen; Henze, Daven K.; Jones, Dylan B. A.; Fischer, Emily V.; Zhu, Liye; Boersma, K. Folkert

2018-01-01

Ground and satellite observations show that air pollution regulations in the United States (US) have resulted in substantial reductions in emissions and corresponding improvements in air quality over the last several decades. However, large uncertainties remain in evaluating how recent regulations affect different emission sectors and pollutant trends. Here we show a significant slowdown in decreasing US emissions of nitrogen oxides (NOx) and carbon monoxide (CO) for 2011–2015 using satellite and surface measurements. This observed slowdown in emission reductions is significantly different from the trend expected using US Environmental Protection Agency (EPA) bottom-up inventories and impedes compliance with local and federal agency air-quality goals. We find that the difference between observations and EPA’s NOx emission estimates could be explained by: (i) growing relative contributions of industrial, area, and off-road sources, (ii) decreasing relative contributions of on-road gasoline, and (iii) slower than expected decreases in on-road diesel emissions. PMID:29712822

Application research on big data in energy conservation and emission reduction of transportation industry

NASA Astrophysics Data System (ADS)

Bai, Bingdong; Chen, Jing; Wang, Mei; Yao, Jingjing

2017-06-01

In the context of big data age, the energy conservation and emission reduction of transportation is a natural big data industry. The planning, management, decision-making of energy conservation and emission reduction of transportation and other aspects should be supported by the analysis and forecasting of large amounts of data. Now, with the development of information technology, such as intelligent city, sensor road and so on, information collection technology in the direction of the Internet of things gradually become popular. The 3G/4G network transmission technology develop rapidly, and a large number of energy conservation and emission reduction of transportation data is growing into a series with different ways. The government not only should be able to make good use of big data to solve the problem of energy conservation and emission reduction of transportation, but also to explore and use a large amount of data behind the hidden value. Based on the analysis of the basic characteristics and application technology of energy conservation and emission reduction of transportation data, this paper carries out its application research in energy conservation and emission reduction of transportation industry, so as to provide theoretical basis and reference value for low carbon management.

Investigation of CO2 emission reduction strategy from in-use gasoline vehicle

NASA Astrophysics Data System (ADS)

Choudhary, Arti; Gokhale, Sharad

2016-04-01

On road transport emissions is kicking off in Indian cities due to high levels of urbanization and economic growth during the last decade in Indian subcontinent. In 1951, about 17% of India's population were living in urban areas that increased to 32% in 2011. Currently, India is fourth largest Green House Gas (GHG) emitter in the world, with its transport sector being the second largest contributor of CO2 emissions. For achieving prospective carbon reduction targets, substantial opportunity among in-use vehicle is necessary to quantify. Since, urban traffic flow and operating condition has significant impact on exhaust emission (Choudhary and Gokhale, 2016). This study examined the influence of vehicular operating kinetics on CO2 emission from predominant private transportation vehicles of Indian metropolitan city, Guwahati. On-board instantaneous data were used to quantify the impact of CO2 emission on different mileage passenger cars and auto-rickshaws at different times of the day. Further study investigates CO2 emission reduction strategies by using International Vehicle Emission (IVE) model to improve co-benefit in private transportation by integrated effort such as gradual phase-out of inefficient vehicle and low carbon fuel. The analysis suggests that fuel type, vehicles maintenance and traffic flow management have potential for reduction of urban sector GHG emissions. Keywords: private transportation, CO2, instantaneous emission, IVE model Reference Choudhary, A., Gokhale, S. (2016). Urban real-world driving traffic emissions during interruption and congestion. Transportation Research Part D: Transport and Environment 43: 59-70.

Development of reduction scenarios for criteria air pollutants emission in Tehran Traffic Sector, Iran.

PubMed

Mohammadiha, Amir; Malakooti, Hossein; Esfahanian, Vahid

2018-05-01

Transport-related pollution as the main source of air pollution must be reduced in Tehran mega-city. The performance of various developed scenarios including BAU (Business As Usual) as baseline scenario, ECV (Elimination of carburetor equipped Vehicle), NEM (New Energy Motorcycles), HES (Higher Emission Standard), VCR (Vehicle Catalyst Replacement), FQE (Fuel Quality Enhancement), DPF (Diesel Particulate Filter) and TSA (Total Scenarios Aggregation) are evaluated by International Vehicle Model up to 2028. In the short term, the ECV, VCR, and FQE scenarios provided high performance in CO, VOCs and NOx emissions control. Also FQE has an excellent effect on SOx emission reduction (86%) and DPF on PM emissions (20%). In the mid-term, the VCR, ECV, and FQE scenarios were presented desirable mean emission reduction on CO, VOCs, and NOx. Moreover, NOx emission reduction of DPF scenario is the most common (14%). Again FQE scenario proves to have great effect on SOx emission reduction in mid-term (86%), DPF and HES scenarios on PM (DPF: 49% and HES: 17%). Finally for the long term, VCR, ECV, FQE, and NEM scenarios were shown good performance in emission control on CO, VOCs and NOx. For SOx only FQE has a good effect in all time periods (FQE: 86%) and DPF and HES scenarios have the best effect on PM emission reduction respectively (DPF: 51% and HES: 27%) compared with BAU scenario. However, DPF scenario increases 12% SOx emission in long-term (2028). It can be generally concluded that VCR and ECV scenarios would achieve a significant reduction on gaseous pollutants emission except for SOx in general and FQE scenarios have desirable performance for all gaseous pollutants in the short term and also for SOx and VOCs in long term. In addition, the DPF and HES would be desirable scenario for emission control on PM in Tehran Traffic Sector. Copyright © 2017 Elsevier B.V. All rights reserved.

Reduction of aircraft gas turbine engine pollutant emissions

NASA Technical Reports Server (NTRS)

Diehl, L. A.

1978-01-01

To accomplish simultaneous reduction of unburned hydrocarbons, carbon monoxide, and oxides of nitrogen, required major modifications to the combustor. The modification most commonly used was a staged combustion technique. While these designs are more complicated than production combustors, no insurmountable operational difficulties were encountered in either high pressure rig or engine tests which could not be resolved with additional normal development. The emission reduction results indicate that reductions in unburned hydrocarbons were sufficient to satisfy both near and far-termed EPA requirements. Although substantial reductions were observed, the success in achieving the CO and NOx standards was mixed and depended heavily on the engine/engine cycle on which it was employed. Technology for near term CO reduction was satisfactory or marginally satisfactory. Considerable doubt exists if this technology will satisfy all far-term requirements.

SPATIAL DISTRIBUTIONS OF ABSORPTION, LOCAL SUPPRESSION, AND EMISSIVITY REDUCTION OF SOLAR ACOUSTIC WAVES IN MAGNETIC REGIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chou, D.-Y.; Yang, M.-H.; Zhao Hui

Observed acoustic power in magnetic regions is lower than the quiet Sun because of absorption, emissivity reduction, and local suppression of solar acoustic waves in magnetic regions. In the previous studies, we have developed a method to measure the coefficients of absorption, emissivity reduction, and local suppression of sunspots. In this study, we go one step further to measure the spatial distributions of three coefficients in two active regions, NOAA 9055 and 9057. The maps of absorption, emissivity reduction, and local suppression coefficients correlate with the magnetic map, including plage regions, except the emissivity reduction coefficient of NOAA 9055 wheremore » the emissivity reduction coefficient is too weak and lost among the noise.« less

40 CFR 93.165 - Early emission reduction credit programs at Federal facilities and installation subject to...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Early emission reduction credit... Federal Actions to State or Federal Implementation Plans § 93.165 Early emission reduction credit programs... the SIP or TIP in that area, create an early emissions reductions credit program. The Federal agency...

40 CFR 93.165 - Early emission reduction credit programs at Federal facilities and installation subject to...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Early emission reduction credit... Federal Actions to State or Federal Implementation Plans § 93.165 Early emission reduction credit programs... the SIP or TIP in that area, create an early emissions reductions credit program. The Federal agency...

GENERIC VERIFICATION PROTOCOL FOR DETERMINATION OF EMISSIONS REDUCTIONS FROM SELECTIVE CATALYTIC REDUCTIONS CONTROL TECHNOLOGIES FOR HIGHWAY, NONROAD, AND STATIONARY USE DIESEL ENGINES

EPA Science Inventory

The protocol describes the Environmental Technology Verification (ETV) Program's considerations and requirements for verification of emissions reduction provided by selective catalytic reduction (SCR) technologies. The basis of the ETV will be comparison of the emissions and perf...

City-specific vehicle emission control strategies to achieve stringent emission reduction targets in China's Yangtze River Delta region.

PubMed

Zhang, Shaojun; Wu, Ye; Zhao, Bin; Wu, Xiaomeng; Shu, Jiawei; Hao, Jiming

2017-01-01

The Yangtze River Delta (YRD) region is one of the most prosperous and densely populated regions in China and is facing tremendous pressure to mitigate vehicle emissions and improve air quality. Our assessment has revealed that mitigating vehicle emissions of NOx would be more difficult than reducing the emissions of other major vehicular pollutants (e.g., CO, HC and PM 2.5 ) in the YRD region. Even in Shanghai, where the emission control implemented are more stringent than in Jiangsu and Zhejiang, we observed little to no reduction in NOx emissions from 2000 to 2010. Emission-reduction targets for HC, NOx and PM 2.5 are determined using a response surface modeling tool for better air quality. We design city-specific emission control strategies for three vehicle-populated cities in the YRD region: Shanghai and Nanjing and Wuxi in Jiangsu. Our results indicate that even if stringent emission control consisting of the Euro 6/VI standards, the limitation of vehicle population and usage, and the scrappage of older vehicles is applied, Nanjing and Wuxi will not be able to meet the NOx emissions target by 2020. Therefore, additional control measures are proposed for Nanjing and Wuxi to further mitigate NOx emissions from heavy-duty diesel vehicles. Copyright © 2016. Published by Elsevier B.V.

Climate and Health Impacts of US Emissions Reductions Consistent with 2 C

NASA Technical Reports Server (NTRS)

Shindell, Drew T.; Lee, Yunha; Faluvegi, Greg

2016-01-01

An emissions trajectory for the US consistent with 2 C warming would require marked societal changes, making it crucial to understand the associated benefits. Previous studies have examined technological potentials and implementation costs and public health benefits have been quantified for less-aggressive potential emissions-reduction policies, but researchers have not yet fully explored the multiple benefits of reductions consistent with 2 C. We examine the impacts of such highly ambitious scenarios for clean energy and vehicles. US transportation emissions reductions avoid approx.0.03 C global warming in 2030 (0.15 C in 2100), whereas energy emissions reductions avoid approx.0.05-0.07 C 2030 warming (approx.0.25 C in 2100). Nationally, however, clean energy policies produce climate disbenefits including warmer summers (although these would be eliminated by the remote effects of similar policies if they were undertaken elsewhere). The policies also greatly reduce damaging ambient particulate matter and ozone. By 2030, clean energy policies could prevent approx.175,000 premature deaths, with approx.22,000 (11,000-96,000; 95% confidence) fewer annually thereafter, whereas clean transportation could prevent approx.120,000 premature deaths and approx.14,000 (9,000-52,000) annually thereafter. Near-term national benefits are valued at approx.US$250 billion (140 billion to 1,050billion) per year, which is likely to exceed implementation costs. Including longer-term, worldwide climate impacts, benefits roughly quintuple, becoming approx.5-10 times larger than estimated implementation costs. Achieving the benefits, however, would require both larger and broader emissions reductions than those in current legislation or regulations.

The advantage of calculating emission reduction with local emission factor in South Sumatera region

NASA Astrophysics Data System (ADS)

Buchari, Erika

2017-11-01

Green House Gases (GHG) which have different Global Warming Potential, usually expressed in CO2 equivalent. German has succeeded in emission reduction of CO2 in year 1990s, while Japan since 2001 increased load factor of public transports. Indonesia National Medium Term Development Plan, 2015-2019, has set up the target of minimum 26% and maximum 41% National Emission Reduction in 2019. Intergovernmental Panel on Climate Change (IPCC), defined three types of accuracy in counting emission of GHG, as tier 1, tier 2, and tier 3. In tier 1, calculation is based on fuel used and average emission (default), which is obtained from statistical data. While in tier 2, calculation is based fuel used and local emission factors. Tier 3 is more accurate from those in tier 1 and 2, and the calculation is based on fuel used from modelling method or from direct measurement. This paper is aimed to evaluate the calculation with tier 2 and tier 3 in South Sumatera region. In 2012, Regional Action Plan for Greenhouse Gases of South Sumatera for 2020 is about 6,569,000 ton per year and with tier 3 is about without mitigation and 6,229,858.468 ton per year. It was found that the calculation in tier 3 is more accurate in terms of fuel used of variation vehicles so that the actions of mitigation can be planned more realistically.

Reviews on current carbon emission reduction technologies and projects and their feasibilities on ships

NASA Astrophysics Data System (ADS)

Wang, Haibin; Zhou, Peilin; Wang, Zhongcheng

2017-06-01

Concern about global climate change is growing, and many projects and researchers are committed to reducing greenhouse gases from all possible sources. International Maritime (IMO) has set a target of 20% CO2 reduction from shipping by 2020 and also presented a series of carbon emission reduction methods, which are known as Energy Efficiency Design Index (EEDI) and Energy Efficiency Operation Indicator (EEOI). Reviews on carbon emission reduction from all industries indicate that, Carbon Capture and Storage (CCS) is an excellent solution to global warming. In this paper, a comprehensive literature review of EEDI and EEOI and CCS is conducted and involves reviewing current policies, introducing common technologies, and considering their feasibilities for marine activities, mainly shipping. Current projects are also presented in this paper, thereby illustrating that carbon emission reduction has been the subject of attention from all over the world. Two case ship studies indicate the economic feasibility of carbon emission reduction and provide a guide for CCS system application and practical installation on ships.

Smart Transportation CO2 Emission Reduction Strategies

NASA Astrophysics Data System (ADS)

Tarulescu, S.; Tarulescu, R.; Soica, A.; Leahu, C. I.

2017-10-01

Transport represents the sector with the fastest growing greenhouse gas emissions around the world. The main global objective is to reduce energy usage and associated greenhouse gas emissions from the transportation sector. For this study it was analyzed the road transportation system from Brasov Metropolitan area. The study was made for the transportation route that connects Ghimbav city to the main surrounding objectives. In this study ware considered four optimization measures: vehicle fleet renewal; building the detour belt for the city; road increasing the average travel speed; making bicycle lanes; and implementing an urban public transport system for Ghimbav. For each measure it was used a mathematical model to calculate the energy consumption and carbon emissions from the road transportation sector. After all four measures was analyzed is calculated the general energy consumption and CO2 reduction if this are applied from year 2017 to 2020.

Reductions in aircraft particulate emissions due to the use of Fischer-Tropsch fuels

NASA Astrophysics Data System (ADS)

Beyersdorf, A. J.; Timko, M. T.; Ziemba, L. D.; Bulzan, D.; Corporan, E.; Herndon, S. C.; Howard, R.; Miake-Lye, R.; Thornhill, K. L.; Winstead, E.; Wey, C.; Yu, Z.; Anderson, B. E.

2014-01-01

The use of alternative fuels for aviation is likely to increase due to concerns over fuel security, price stability, and the sustainability of fuel sources. Concurrent reductions in particulate emissions from these alternative fuels are expected because of changes in fuel composition including reduced sulfur and aromatic content. The NASA Alternative Aviation Fuel Experiment (AAFEX) was conducted in January-February 2009 to investigate the effects of synthetic fuels on gas-phase and particulate emissions. Standard petroleum JP-8 fuel, pure synthetic fuels produced from natural gas and coal feedstocks using the Fischer-Tropsch (FT) process, and 50% blends of both fuels were tested in the CFM-56 engines on a DC-8 aircraft. To examine plume chemistry and particle evolution with time, samples were drawn from inlet probes positioned 1, 30, and 145 m downstream of the aircraft engines. No significant alteration to engine performance was measured when burning the alternative fuels. However, leaks in the aircraft fuel system were detected when operated with the pure FT fuels as a result of the absence of aromatic compounds in the fuel. Dramatic reductions in soot emissions were measured for both the pure FT fuels (reductions in mass of 86% averaged over all powers) and blended fuels (66%) relative to the JP-8 baseline with the largest reductions at idle conditions. At 7% power, this corresponds to a reduction from 7.6 mg kg-1 for JP-8 to 1.2 mg kg-1 for the natural gas FT fuel. At full power, soot emissions were reduced from 103 to 24 mg kg-1 (JP-8 and natural gas FT, respectively). The alternative fuels also produced smaller soot (e.g., at 85% power, volume mean diameters were reduced from 78 nm for JP-8 to 51 nm for the natural gas FT fuel), which may reduce their ability to act as cloud condensation nuclei (CCN). The reductions in particulate emissions are expected for all alternative fuels with similar reductions in fuel sulfur and aromatic content regardless of the

Augmentor emissions reduction technology program. [for turbofan engines

NASA Technical Reports Server (NTRS)

Colley, W. C.; Kenworthy, M. J.; Bahr, D. W.

1977-01-01

Technology to reduce pollutant emissions from duct-burner-type augmentors for use on advanced supersonic cruise aircraft was investigated. Test configurations, representing variations of two duct-burner design concepts, were tested in a rectangular sector rig at inlet temperature and pressure conditions corresponding to takeoff, transonic climb, and supersonic cruise flight conditions. Both design concepts used piloted flameholders to stabilize combustion of lean, premixed fuel/air mixtures. The concepts differed in the flameholder type used. High combustion efficiency (97%) and low levels of emissions (1.19 g/kg fuel) were achieved. The detailed measurements suggested the direction that future development efforts should take to obtain further reductions in emission levels and associated improvements in combustion efficiency over an increased range of temperature rise conditions.

Combustor concepts for aircraft gas turbine low-power emissions reduction

NASA Technical Reports Server (NTRS)

Mularz, E. J.; Gleason, C. C.; Dodds, W. J.

1978-01-01

Several combustor concepts were designed and tested to demonstrate significant reductions in aircraft engine idle pollutant emissions. Each concept used a different approach for pollutant reductions: the hot wall combustor employs a thermal barrier coating and impingement cooled liners; the recuperative cooling combustor preheats the air before entering the combustion chamber; and the catalytic converter combustor is composed of a conventional primary zone followed by a catalytic bed for pollutant cleanup. The designs are discussed in detail and test results are presented for a range of aircraft engine idle conditions. The results indicate that ultralow levels of unburned hydrocarbons and carbon monoxide emissions can be achieved.

Ozone response to emission reductions in the southeastern United States

NASA Astrophysics Data System (ADS)

Blanchard, Charles L.; Hidy, George M.

2018-06-01

Ozone (O3) formation in the southeastern US is studied in relation to nitrogen oxide (NOx) emissions using long-term (1990s-2015) surface measurements of the Southeastern Aerosol Research and Characterization (SEARCH) network, U.S. Environmental Protection Agency (EPA) O3 measurements, and EPA Clean Air Status and Trends Network (CASTNET) nitrate deposition data. Annual fourth-highest daily peak 8 h O3 mixing ratios at EPA monitoring sites in Georgia, Alabama, and Mississippi exhibit statistically significant (p < 0.0001) linear correlations with annual NOx emissions in those states between 1996 and 2015. The annual fourth-highest daily peak 8 h O3 mixing ratios declined toward values of ˜ 45-50 ppbv and monthly O3 maxima decreased at rates averaging ˜ 1-1.5 ppbv yr-1. Mean annual total oxidized nitrogen (NOy) mixing ratios at SEARCH sites declined in proportion to NOx emission reductions. CASTNET data show declining wet and dry nitrate deposition since the late 1990s, with total (wet plus dry) nitrate deposition fluxes decreasing linearly in proportion to reductions of NOx emissions by ˜ 60 % in Alabama and Georgia. Annual nitrate deposition rates at Georgia and Alabama CASTNET sites correspond to 30 % of Georgia emission rates and 36 % of Alabama emission rates, respectively. The fraction of NOx emissions lost to deposition has not changed. SEARCH and CASTNET sites exhibit downward trends in mean annual nitric acid (HNO3) concentrations. Observed relationships of O3 to NOz (NOy-NOx) support past model predictions of increases in cycling of NO and increasing responsiveness of O3 to NOx. The study data provide a long-term record that can be used to examine the accuracy of process relationships embedded in modeling efforts. Quantifying observed O3 trends and relating them to reductions in ambient NOy species concentrations offers key insights into processes of general relevance to air quality management and provides important information supporting strategies for

Optimized deployment of emission reduction technologies for large fleets.

DOT National Transportation Integrated Search

2011-06-01

This research study produced an optimization framework for determining the most efficient emission : reduction strategies among vehicles and equipment in a large fleet. The Texas Department of : Transportations (TxDOTs) fleet data were utilized...

The international research progress of Ammonia(NH3) emissions and emissions reduction technology in farmland ecosystem

NASA Astrophysics Data System (ADS)

Yang, W. Z.; Jiao, Y.

2017-03-01

NH3 is the important factor leading to the grey haze, and one of the main causes of environmental problems of serious ecological imbalance, such as acid rain and air quality deterioration. The fertilizer excessive application of the current farmland results NH3 emissions intensity greatly. In order to clear the farmland NH3 emissions research status and achievements, the literature of farmland NH3 emission related were retrievaled by the SCI journals and Chinese science citation database. Some factors of NH3 emission were analyzed such as soil factors, climate factors and farmland management measures. The research progress was inductived on farmland NH3 emission reduction technology. The results will help to clarify farmland NH3 emissions research progress. The theoretical guidance was provided on the future of farmland NH3 emissions research.

Diesel engine emissions reduction by multiple injections having increasing pressure

DOEpatents

Reitz, Rolf D.; Thiel, Matthew P.

2003-01-01

Multiple fuel charges are injected into a diesel engine combustion chamber during a combustion cycle, and each charge after the first has successively greater injection pressure (a higher injection rate) than the prior charge. This injection scheme results in reduced emissions, particularly particulate emissions, and can be implemented by modifying existing injection system hardware. Further enhancements in emissions reduction and engine performance can be obtained by using known measures in conjunction with the invention, such as Exhaust Gas Recirculation (EGR).

Aerosol reductions could dominate regional climate responses in low GHG emission scenarios

NASA Astrophysics Data System (ADS)

Samset, B. H.; Sand, M.; Smith, C. J.; Bauer, S.; Forster, P.; Fuglestvedt, J. S.; Osprey, S. M.; Schleussner, C. F.

2017-12-01

Limiting global warming to current political goals requires strong, rapid mitigation of anthropogenic greenhouse gas (GHG) emissions. Concurrently, emissions of anthropogenic aerosols will decline sharply, due to co-emission with greenhouse gases, and future measures to improve air quality. As the net climate effect of GHG and aerosol emissions over the industrial era is poorly constrained, predicting the impact of strong aerosol emission reductions remains challenging. Here we investigate the isolated and compound climate impacts from removing present day anthropogenic emissions of black carbon (BC), organic carbon (OC) and SO2, and moderate, near term GHG dominated global warming, using four coupled climate models. As the dominating effect of aerosol emission reduction is a removal of cooling from sulphur, the resulting climate impacts amplify those of GHG induced warming. BC emissions contribute little to reducing surface warming, but have stronger regional impacts. For the major aerosol emission regions, extreme weather indices are more sensitive to aerosol removal than to GHG increases, per degree of surface warming. East Asia in particular stands out, mainly due to the high present regional aerosol emissions. We show how present climate models indicate that future regional climate change will depend strongly on changes in loading and distribution of aerosols in the atmosphere, in addition to surface temperature change.

Future development programs. [for emission reduction and production of aircraft engines

NASA Technical Reports Server (NTRS)

Waters, L.

1976-01-01

A company program was planned which has a main drive to develop those emission reduction concepts that have the promise of earliest success. These programs were proposed in an attempt to enhance existing engine systems, exploiting their potential for emission reduction as far as is compatible with retaining the well established features in them that are well understood and in current production. The intended programs identified in the area of new concepts were: (1) upgrading the TCM fuel system, (2) evaluation of accelerator pump, (3) reduced cooling requirement, and (4) variable spark timing.

Sharing global CO2 emission reductions among one billion high emitters

PubMed Central

Chakravarty, Shoibal; Chikkatur, Ananth; de Coninck, Heleen; Pacala, Stephen; Socolow, Robert; Tavoni, Massimo

2009-01-01

We present a framework for allocating a global carbon reduction target among nations, in which the concept of “common but differentiated responsibilities” refers to the emissions of individuals instead of nations. We use the income distribution of a country to estimate how its fossil fuel CO2 emissions are distributed among its citizens, from which we build up a global CO2 distribution. We then propose a simple rule to derive a universal cap on global individual emissions and find corresponding limits on national aggregate emissions from this cap. All of the world's high CO2-emitting individuals are treated the same, regardless of where they live. Any future global emission goal (target and time frame) can be converted into national reduction targets, which are determined by “Business as Usual” projections of national carbon emissions and in-country income distributions. For example, reducing projected global emissions in 2030 by 13 GtCO2 would require the engagement of 1.13 billion high emitters, roughly equally distributed in 4 regions: the U.S., the OECD minus the U.S., China, and the non-OECD minus China. We also modify our methodology to place a floor on emissions of the world's lowest CO2 emitters and demonstrate that climate mitigation and alleviation of extreme poverty are largely decoupled. PMID:19581586

Massport Air Emission Reduction Efforts and Community Enhancement Projects

EPA Pesticide Factsheets

This page describes efforts at Massport to reduce their emissions, including their Clean Truck Replacement program at Conley Terminal, their rubber tire gantry crane repower, idle and truck trip reductions, park creation, and dedicated freight corridor.

Screening analysis and selection of emission reduction concepts for intermittent combustion aircraft engines

NASA Technical Reports Server (NTRS)

Rezy, B. J.; Meyers, J. E.; Tucker, J. R.; Stuckas, S. J.

1976-01-01

An analysis was conducted to screen, evaluate, and select three engine exhaust emission reduction concepts from a group of 14 candidate alternatives. A comprehensive literature search was conducted to survey the emission reduction technology state-of-the-art and establish contact with firms working on intermittent combustion engine development and pollution reduction problems. Concept development, advantages, disadvantages, and expected emission reduction responses are stated. A set of cost effectiveness criteria was developed, appraised for relative importance, and traded off against each concept so that its merit could be determined. A decision model was used to aid the evaluators in managing the criteria, making consistent judgements, calculating merit scores, and ranking the concepts. An Improved Fuel Injection System, Improved Cooling Combustion Chamber, and a Variable Timing Ignition System were recommended to NASA for approval and further concept development. An alternate concept, Air Injection, was also recommended.

Analyzing and forecasting CO2 emission reduction in China's steel industry

NASA Astrophysics Data System (ADS)

Gao, Chengkang; Wang, Dan; Zhao, Baohua; Chen, Shan; Qin, Wei

2015-03-01

Recent measures of carbon dioxide emissions from the steel industry of China have indicated a high rate of total CO2 emissions from the industry, even compared to the rest of the world. So, CO2 emission reduction in China's steel industry was analyzed, coupling the whole process and scenarios analysis. First, assuming that all available advanced technologies are almost adopted, this study puts forward some key potential-sectors and explores an optimal technical route for reducing CO2 emissions from the Chinese steel industry based on whole process analysis. The results show that in the stages of coking, sintering, and iron making, greater potential for reducing emissions would be fulfilled by taking some technological measures. If only would above well-developed technologies be fulfill, the CO2 emissions from 5 industry production stages would be reduced substantially, and CO2 emissions per ton of steel could be decreased to 1.24 (ton/ton-steel) by 2020. At the same time, the scenarios analysis indicates that if mature carbon-reducing technologies are adopted, and if the difference between steel output growth rate and the GDP growth rate could be controlled below 3%, CO2 emissions from China's steel industry would approach the goal of reducing CO2 emissions per GDP unit by 40%-45% of the 2005 level by 2020. This indicates that the focus of carbon dioxide emissions reduction in China lies in policy adjustments in order to enhance technological application, and lies in reasonably controlling the pace of growth of GDP and steel output.

Experimental investigation on emission reduction in neem oil biodiesel using selective catalytic reduction and catalytic converter techniques.

PubMed

Viswanathan, Karthickeyan

2018-05-01

In the present study, non-edible seed oil namely raw neem oil was converted into biodiesel using transesterification process. In the experimentation, two biodiesel blends were prepared namely B25 (25% neem oil methyl ester with 75% of diesel) and B50 (50% neem oil methyl ester with 50% diesel). Urea-based selective catalytic reduction (SCR) technique with catalytic converter (CC) was fixed in the exhaust tail pipe of the engine for the reduction of engine exhaust emissions. Initially, the engine was operated with diesel as a working fluid and followed by refilling of biodiesel blends B25 and B50 to obtain the baseline readings without SCR and CC. Then, the same procedure was repeated with SCR and CC technique for emission reduction measurement in diesel, B25 and B50 sample. The experimental results revealed that the B25 blend showed higher break thermal efficiency (BTE) and exhaust gas temperature (EGT) with lower break-specific fuel consumption (BSFC) than B50 blend at all loads. On comparing with biodiesel blends, diesel experiences increased BTE of 31.9% with reduced BSFC of 0.29 kg/kWh at full load. A notable emission reduction was noticed for all test fuels in SCR and CC setup. At full load, B25 showed lower carbon monoxide (CO) of 0.09% volume, hydrocarbon (HC) of 24 ppm, and smoke of 14 HSU and oxides of nitrogen (NOx) of 735 ppm than diesel and B50 in SCR and CC setup. On the whole, the engine with SCR and CC setup showed better performance and emission characteristics than standard engine operation.

Reductions in aircraft particulate emissions due to the use of Fischer-Tropsch fuels

NASA Astrophysics Data System (ADS)

Beyersdorf, A. J.; Timko, M. T.; Ziemba, L. D.; Bulzan, D.; Corporan, E.; Herndon, S. C.; Howard, R.; Miake-Lye, R.; Thornhill, K. L.; Winstead, E.; Wey, C.; Yu, Z.; Anderson, B. E.

2013-06-01

The use of alternative fuels for aviation is likely to increase due to concerns over fuel security, price stability and the sustainability of fuel sources. Concurrent reductions in particulate emissions from these alternative fuels are expected because of changes in fuel composition including reduced sulfur and aromatic content. The NASA Alternative Aviation Fuel Experiment (AAFEX) was conducted in January-February 2009 to investigate the effects of synthetic fuels on gas-phase and particulate emissions. Standard petroleum JP-8 fuel, pure synthetic fuels produced from natural gas and coal feedstocks using the Fischer-Tropsch (FT) process, and 50% blends of both fuels were tested in the CFM-56 engines on a DC-8 aircraft. To examine plume chemistry and particle evolution with time, samples were drawn from inlet probes positioned 1, 30, and 145 m downstream of the aircraft engines. No significant alteration to engine performance was measured when burning the alternative fuels. However, leaks in the aircraft fuel system were detected when operated with the pure FT fuels as a result of the absence of aromatic compounds in the fuel. Dramatic reductions in soot emissions were measured for both the pure FT fuels (reductions of 84% averaged over all powers) and blended fuels (64%) relative to the JP-8 baseline with the largest reductions at idle conditions. The alternative fuels also produced smaller soot (e.g. at 85% power, volume mean diameters were reduced from 78 nm for JP-8 to 51 nm for the FT fuel), which may reduce their ability to act as cloud condensation nuclei (CCN). The reductions in particulate emissions are expected for all alternative fuels with similar reductions in fuel sulfur and aromatic content regardless of the feedstock. As the plume cools downwind of the engine, nucleation-mode aerosols form. For the pure FT fuels, reductions (94% averaged over all powers) in downwind particle number emissions were similar to those measured at the exhaust plane (84

Alternative technologies for the reduction of greenhouse gas emissions from palm oil mills in Thailand.

PubMed

Kaewmai, Roihatai; H-Kittikun, Aran; Suksaroj, Chaisri; Musikavong, Charongpun

2013-01-01

Alternative methodologies for the reduction of greenhouse gas (GHG) emissions from crude palm oil (CPO) production by a wet extraction mill in Thailand were developed. The production of 1 t of CPO from mills with biogas capture (four mills) and without biogas capture (two mills) in 2010 produced GHG emissions of 935 kg carbon dioxide equivalent (CO2eq), on average. Wastewater treatment plants with and without biogas capture produced GHG emissions of 64 and 47% of total GHG emission, respectively. The rest of the emissions mostly originated from the acquisition of fresh fruit bunches. The establishment of a biogas recovery system must be the first step in the reduction of GHG emissions. It could reduce GHG emissions by 373 kgCO2eq/t of CPO. The main source of GHG emission of 163 kgCO2eq/t of CPO from the mills with biogas capture was the open pond used for cooling of wastewater before it enters the biogas recovery system. The reduction of GHG emissions could be accomplished by (i) using a wastewater-dispersed unit for cooling, (ii) using a covered pond, (iii) enhancing the performance of the biogas recovery system, and (iv) changing the stabilization pond to an aerated lagoon. By using options i-iv, reductions of GHG emissions of 216, 208, 92.2, and 87.6 kgCO2eq/t of CPO, respectively, can be achieved.

EMISSIONS REDUCTION DATA FOR GRID-CONNECTED PHOTOVOLTAIC POWER SYSTEMS

EPA Science Inventory

This study measured the pollutant emission reduction potential of 29 photovoltaic (PV) systems installed on residential and commercial building rooftops across the U.S. from 1993 through 1997. The U.S. Environmental Protection Agency (EPA) and 21 electric power companies sponsor...

Impact of fuel quality regulation and speed reductions on shipping emissions: implications for climate and air quality.

PubMed

Lack, Daniel A; Cappa, Christopher D; Langridge, Justin; Bahreini, Roya; Buffaloe, Gina; Brock, Charles; Cerully, Kate; Coffman, Derek; Hayden, Katherine; Holloway, John; Lerner, Brian; Massoli, Paola; Li, Shao-Meng; McLaren, Robert; Middlebrook, Ann M; Moore, Richard; Nenes, Athanasios; Nuaaman, Ibraheem; Onasch, Timothy B; Peischl, Jeff; Perring, Anne; Quinn, Patricia K; Ryerson, Tom; Schwartz, Joshua P; Spackman, Ryan; Wofsy, Steven C; Worsnop, Doug; Xiang, Bin; Williams, Eric

2011-10-15

Atmospheric emissions of gas and particulate matter from a large ocean-going container vessel were sampled as it slowed and switched from high-sulfur to low-sulfur fuel as it transited into regulated coastal waters of California. Reduction in emission factors (EFs) of sulfur dioxide (SO₂), particulate matter, particulate sulfate and cloud condensation nuclei were substantial (≥ 90%). EFs for particulate organic matter decreased by 70%. Black carbon (BC) EFs were reduced by 41%. When the measured emission reductions, brought about by compliance with the California fuel quality regulation and participation in the vessel speed reduction (VSR) program, are placed in a broader context, warming from reductions in the indirect effect of SO₄ would dominate any radiative changes due to the emissions changes. Within regulated waters absolute emission reductions exceed 88% for almost all measured gas and particle phase species. The analysis presented provides direct estimations of the emissions reductions that can be realized by California fuel quality regulation and VSR program, in addition to providing new information relevant to potential health and climate impact of reduced fuel sulfur content, fuel quality and vessel speed reductions.

Study of combustion and emission characteristics of fuel derived from waste plastics by various waste to energy (W-t-E) conversion processes

NASA Astrophysics Data System (ADS)

Hazrat, M. A.; Rasul, M. G.; Khan, M. M. K.

2016-07-01

Reduction of plastic wastes by means of producing energy can be treated as a good investment in the waste management and recycling sectors. In this article, conversion of plastics into liquid fuel by two thermo-chemical processes, pyrolysis and gasification, are reviewed. The study showed that the catalytic pyrolysis of homogenous waste plastics produces better quality and higher quantity of liquefied fuel than that of non-catalytic pyrolysis process at a lower operating temperature. The syngas produced from gasification process, which occurs at higher temperature than the pyrolysis process, can be converted into diesel by the Fischer-Tropsch (FT) reaction process. Conducive bed material like Olivine in the gasification conversion process can remarkably reduce the production of tar. The waste plastics pyrolysis oil showed brake thermal efficiency (BTE) of about 27.75%, brake specific fuel consumption (BSFC) of 0.292 kg/kWh, unburned hydrocarbon emission (uHC) of 91 ppm and NOx emission of 904 ppm in comparison with the diesel for BTE of 28%, BSFC of 0.276 kg/kWh, uHC of 57 ppm and NOx of 855 ppm. Dissolution of Polystyrene (PS) into biodiesel also showed the potential of producing alternative transport fuel. It has been found from the literature that at higher engine speed, increased EPS (Expanded Polystyrene) quantity based biodiesel blends reduces CO, CO2, NOx and smoke emission. EPS-biodiesel fuel blend increases the brake thermal efficiency by 7.8%, specific fuel consumption (SFC) by 7.2% and reduces brake power (Pb) by 3.2%. More study using PS and EPS with other thermoplastics is needed to produce liquid fuel by dissolving them into biodiesel and to assess their suitability as a transport fuel. Furthermore, investigation to find out most suitable W-t-E process for effective recycling of the waste plastics as fuel for internal combustion engines is necessary to reduce environmental pollution and generate revenue which will be addressed in this article.

Emissions of Jatropha oil-derived biodiesel blend fuels during combustion in a swirl burner

NASA Astrophysics Data System (ADS)

Norwazan, A. R.; Mohd. Jaafar, M. N.; Sapee, S.; Farouk, Hazir

2018-03-01

Experimental works on combustion of jatropha oil biodiesel blends of fuel with high swirling flow in swirl burner have been studied in various blends percentage. Jatropha oil biodiesel was produced using a two-step of esterification-transesterification process. The paper focuses on the emissions of biodiesel blends fuel using jatropha oil in lean through to rich air/fuel mixture combustion in swirl burner. The emissions performances were evaluated by using axial swirler amongst jatropha oil blends fuel including diesel fuel as baseline. The results show that the B25 has good emissions even though it has a higher emission of NOx than diesel fuel, while it emits as low as 42% of CO, 33% of SO2 and 50% of UHC emissions with high swirl number. These are due to the higher oxygen content in jatropha oil biodiesel.

Adaptive Engine Technologies for Aviation CO2 Emissions Reduction

NASA Technical Reports Server (NTRS)

Mercer, Carolyn R.; Haller, William J.; Tong, Michael T.

2006-01-01

Adaptive turbine engine technologies are assessed for their potential to reduce carbon dioxide emissions from commercial air transports.Technologies including inlet, fan, and compressor flow control, compressor stall control, blade clearance control, combustion control, active bearings and enabling technologies such as active materials and wireless sensors are discussed. The method of systems assessment is described, including strengths and weaknesses of the approach. Performance benefit estimates are presented for each technology, with a summary of potential emissions reduction possible from the development of new, adaptively controlled engine components.

Carbon flow analysis and Carbon emission reduction of FCC in Chinese oil refineries

NASA Astrophysics Data System (ADS)

Jia, Fengrui; Wei, Na; Ma, Danzhu; Liu, Guangxin; Wu, Ming; Yue, Qiang

2017-08-01

The major problem of the energy production in oil refineries is the high emission of CO2 in China. The fluid catalytic cracking unit (FCC) is the key source of carbon emission in the oil refineries. According to the statistical data, the carbon emission of FCC unit accounts for more than 31% for the typical oil refineries. The carbon flow of FCC in the typical Chinese oil refineries were evaluated and analysed, which aimed at the solution of CO2 emission reduction. The method of substances flow analysis (SFA) and the mathematical programming were used to evaluate the carbon metabolism and optimize the carbon emission. The results indicated that the combustion emission of the reaction-regeneration subsystem (RRS) was the major source of FCC. The quantity of CO2 emission of RSS was more than 90%. The combustion efficiency and the amount of residual oil affected the carbon emission of RRS most according to the optimized analysis of carbon emission reduction. Moreover, the fractionation subsystem (TFS) had the highest environmental efficiency and the absorption-stabilization subsystem (ASS) had the highest resource efficiency (approximately to 1) of carbon.

Climate and mortality changes due to reductions in household cooking emissions

NASA Astrophysics Data System (ADS)

Bergman, Tommi; Mielonen, Tero; Arola, Antti; Kokkola, Harri

2016-04-01

Household cooking is a significant cause for health and environmental problems in the developing countries. There are more than 3 billion people who use biomass for fuel in cooking stoves in their daily life. These cooking stoves use inadequate ventilation and expose especially women and children to indoor smoke. To reduce problems of the biomass burning, India launched an initiative to provide affordable and clean energy solutions for the poorest households by providing clean next-generation cooking stoves. The improved cooking stoves are expected to improve outdoor air quality and to reduce the climate-active pollutants, thus simultaneously slowing the climate change. Previous research has shown that the emissions of black carbon can be decreased substantially, as much as 90 % by applying better technology in cooking stoves. We have implemented reasonable (50% decrease) and best case (90% decrease) scenarios of the reductions in black and organic carbon due to improved cooking stoves in India into ECHAM-HAMMOZ aerosol-climate model. The global simulations of the scenarios will be used to study how the reductions of emissions in India affect the pollutant concentrations and radiation. The simulated reductions in particulate concentrations will also be used to estimate the decrease in mortality rates. Furthermore, we will study how the emission reductions would affect the global climate and mortality if a similar initiative would be applied in other developing countries.

IMPACT OF EMISSION REDUCTIONS ON EXPOSURES AND EXPOSURE DISTRIBUTIONS: APPLICATION OF A GEOGRAPHIC EXPOSURE MODEL

EPA Science Inventory

Anticipated results include the following. (1) We will estimate intake fraction (i.e., the fraction of emissions that are inhaled) for major source categories, over time, and by spatial location. Higher intake fraction indicates a greater exposure reduction per emission reduct...

Numerical Study of Low Emission Gas Turbine Combustor Concepts

NASA Technical Reports Server (NTRS)

Yang, Song-Lin

2002-01-01

To further reduce pollutant emissions, such as CO, NO(x), UHCs, etc., in the next few decades, innovative concepts of gas turbine combustors must be developed. Several concepts, such as the LIPP (Lean- Premixed- Prevaporized), RQL (Rich-Burn Quick-Quench Lean-Burn), and LDI (Lean-Direct-Injection), have been under study for many years. To fully realize the potential of these concepts, several improvements, such as inlet geometry, air swirler, aerothermochemistry control, fuel preparation, fuel injection and injector design, etc., must be made, which can be studied through the experimental method and/or the numerical technique. The purpose of this proposal is to use the CFD technique to study, and hence, to guide the design process for low emission gas turbine combustors. A total of 13 technical papers have been (or will be) published.

Linked Analysis of East Asia Emission Reduction Pathways

NASA Astrophysics Data System (ADS)

Kim, Y.; Woo, J. H.; Bu, C.; Lee, Y.; Kim, J.; Jang, Y.; Park, M.

2017-12-01

Air pollution and its impacts over the Northeast Asia are very severe because of the massive pollutant emissions and high population. Korea has been trying to improve air quality with the enhanced environmental legislation. The air quality over Korea, however, does not entirely dependent on its local emissions. Transboundary air pollution from China highly affects Korean atmosphere. The purpose of this research is to understand role of local and transbounday efforts to improve air quality changes over Korea. In this research, we have tried to set up the multiple emission scenario pathways for Korea and China using IIASA's GAINS (Greenhouse gas - Air pollution Interactions aNd Synergies) modeling framework. More up-to-date growth factors and control policy packets were made using regional socio-economic data and control policy information from local governments and international statistics. Four major scenario pathways, 1) Base (Baseline: current legislation), 2) OTB/OTB(On the book/On the way : existing control measure/planed control measure), 3) BOTW_GHG(Beyond on the way : OTW with GHG reduction plan), 4) BOTW_NH3 (OTW with additional NH3 reduction measure) were developed to represent air quality improvement pathways in consideration of both Korean and Chinese efforts. Strict ambient PM2.5 standards from Seoul metropolitan Air quality Improvement Plan(SAIP) seems too enthusiastic without linking air quality control efforts of China. Step-by-step emission controls and following air quality, control cost, health impact from each scenario will be presented at the conference. This subject is supported by Korea Ministry of Environment as "Climate Change Correspondence Program". And This work was supported under the framework of national strategy project on fine particulate matters by Ministry of Science, ICT and Future Planning.

Emissions Reduction Policies and Recent Trends in Southern California’s Ambient Air Quality

PubMed Central

Lurmann, Fred; Gilliland, Frank

2017-01-01

To assess accountability and effectiveness of air regulatory policies, we reviewed over 20 years of monitoring data, emissions estimates, and regulatory policies across several Southern California communities participating in a long-term study of children’s health. Between 1994 and 2011, air quality improved for NO2 and PM2.5 in virtually all the monitored communities. Average NO2 declined 28% to 53%, and PM2.5 decreased 13% to 54%. Year-to-year PM2.5 variability at lower-pollution sites was large compared to changes in long-term trends. PM10 and O3 decreases were largest in communities that were initially among the most polluted. Trends in annual average NO2, PM2.5, and PM10 concentrations in higher pollution communities were generally consistent with NOx, ROG, SOx, PM2.5, and PM10 emissions decreases. Reductions observed at one of the higher PM2.5 sites, Mira Loma, was generally within the range expected from reductions observed in ROG, NOx, SOx, and PM2.5 emissions. Despite a 38% increase in regional motor vehicle activity, vigorous economic growth, and a 30% population increase, total estimated emissions of NOx, ROG, SOx, PM2.5, and PM10 decreased by 54%, 65%, 40%, 21%, and 15%, respectively, during the 20-year time period. Emission control strategies in California have achieved dramatic reductions in ambient NO2, O3, PM2.5, and PM10. However, additional reductions will still be needed to achieve current health-based clean air standards. PMID:25947128

Emission Reduction of Fuel-Staged Aircraft Engine Combustor Using an Additional Premixed Fuel Nozzle.

PubMed

Yamamoto, Takeshi; Shimodaira, Kazuo; Yoshida, Seiji; Kurosawa, Yoji

2013-03-01

The Japan Aerospace Exploration Agency (JAXA) is conducting research and development on aircraft engine technologies to reduce environmental impact for the Technology Development Project for Clean Engines (TechCLEAN). As a part of the project, combustion technologies have been developed with an aggressive target that is an 80% reduction over the NO x threshold of the International Civil Aviation Organization (ICAO) Committee on Aviation Environmental Protection (CAEP)/4 standard. A staged fuel nozzle with a pilot mixer and a main mixer was developed and tested using a single-sector combustor under the target engine's landing and takeoff (LTO) cycle conditions with a rated output of 40 kN and an overall pressure ratio of 25.8. The test results showed a 77% reduction over the CAEP/4 NO x standard. However, the reduction in smoke at thrust conditions higher than the 30% MTO condition and of CO emission at thrust conditions lower than the 85% MTO condition are necessary. In the present study, an additional fuel burner was designed and tested with the staged fuel nozzle in a single-sector combustor to control emissions. The test results show that the combustor enables an 82% reduction in NO x emissions relative to the ICAO CAEP/4 standard and a drastic reduction in smoke and CO emissions.

Carbon emissions from Southeast Asian peatlands will increase despite emission-reduction schemes.

PubMed

Wijedasa, Lahiru S; Sloan, Sean; Page, Susan E; Clements, Gopalasamy R; Lupascu, Massimo; Evans, Theodore A

2018-06-01

Carbon emissions from drained peatlands converted to agriculture in Southeast Asia (i.e. Peninsular Malaysia, Sumatra and Borneo) are globally significant and increasing. Here, we map the growth of Southeast Asian peatland agriculture and estimate CO 2 emissions due to peat drainage in relation to official land-use plans with a focus on the Reducing Emissions from Deforestation and Degradation (REDD+) related Indonesian moratorium on granting new concession licenses for industrial agriculture and logging. We find that, prior to 2010, 35% of Southeast Asian peatlands had been converted to agriculture, principally by smallholder farmers (15% of original peat extent) and industrial oil palm plantations (14%). These conversions resulted in 1.46-6.43 GtCO 2 of emissions between 1990 and 2010. This legacy of historical clearances on deep peat areas will contribute 51% (4.43-11.45 GtCO 2 ) of projected peatland CO 2 emissions over the period 2010-2130. In Indonesia, which hosts most of the region's peatland and where concession maps are publicly available, 70% of peatland conversion to agriculture occurred outside of known concessions for industrial plantation development, with smallholders accounting for 60% and industrial oil palm accounting for 34%. Of the remaining Indonesian peatswamp forest (PSF), 45% is not protected, and its conversion would amount to CO 2 emissions equivalent to 0.7-2.3% (5.14-14.93 Gt) of global fossil fuel and cement emissions released between 1990-2010. Of the peatland extent included in the moratorium, 48% was no longer forested, and of the PSF included 40-48% is likely to be affected by drainage impacts from agricultural areas and will emit CO 2 over time. We suggest that recent legislation and policy in Indonesia could provide a means of meaningful emission reductions if focused on revised land-use planning, PSF conservation both inside and outside agricultural concessions, and the development of agricultural practices based on

Assessment of Co-benefits of vehicle emission reduction measures for 2015-2020 in the Pearl River Delta region, China.

PubMed

Liu, Yong-Hong; Liao, Wen-Yuan; Lin, Xiao-Fang; Li, Li; Zeng, Xue-Lan

2017-04-01

Vehicle emissions have become one of the key factors affecting the urban air quality and climate change in the Pearl River Delta (PRD) region, so it is important to design policies of emission reduction based on quantitative Co-benefits for air pollutants and greenhouse gas (GHG). Emissions of air pollutants and GHG by 2020 was predicted firstly based on the no-control scenario, and five vehicle emissions reduction scenarios were designed in view of the economy, technology and policy, whose emissions reduction were calculated. Then Co-benefits between air pollutants and GHG were quantitatively analyzed by the methods of coordinate system and cross-elasticity. Results show that the emissions reduction effects and the Co-benefits of different measures vary greatly in 2015-2020. If no control scheme was applied, most air pollutants and GHG would increase substantially by 20-64% by 2020, with the exception of CO, VOC and PM 2.5 . Different control measures had different reduction effects for single air pollutant and GHG. The worst reduction measure was Eliminating Motorcycles with average reducing rate 0.09% for air pollutants and GHG, while the rate from Updated Emission Standard was 41.74%. Eliminating Yellow-label Vehicle scenario had an obvious reduction effect for every single pollutant in the earlier years, but Co-benefits would descent to zero in later by 2020. From the perspective of emission reductions and co-control effect, Updated Emission Standard scenario was best for reducing air pollutants and GHG substantially (tanα=1.43 and Els=1.77). Copyright © 2016 Elsevier Ltd. All rights reserved.

[Awareness of health co-benefits of carbon emissions reduction in urban residents in Beijing: a cross-sectional survey].

PubMed

Gao, J H; Zhang, Y; Wang, J; Chen, H J; Zhang, G B; Liu, X B; Wu, H X; Li, J; Li, J; Liu, Q Y

2017-05-10

Objective: To understand the awareness of the health co-benefits of carbon emission reduction in urban residents in Beijing and the influencing factors, and provide information for policy decision on carbon emission reduction and health education campaigns. Methods: Four communities were selected randomly from Fangshan, Haidian, Huairou and Dongcheng districts of Beijing, respectively. The sample size was estimated by using Kish-Leslie formula for descriptive analysis. 90 participants were recruited from each community. χ (2) test was conducted to examine the associations between socio-demographic variables and individuals' awareness of the health co-benefits of carbon emission reduction. Ordinal logistic regression analysis was performed to investigate the factors influencing the awareness about the health co-benefits. Results: In 369 participants surveyed, 12.7 % reported they knew the health co-benefits of carbon emission reduction. The final logistic regression analysis revealed that age ( OR =0.98), attitude to climate warming ( OR =0.72) and air pollution ( OR =1.59), family monthly average income ( OR =1.27), and low carbon lifestyle ( OR =2.36) were important factors influencing their awareness of the health co-benefits of carbon emission reduction. Conclusion: The awareness of the health co-benefits of carbon emissions reduction were influenced by people' socio-demographic characteristics (age and family income), concerns about air pollution and climate warming, and low carbon lifestyle. It is necessary to take these factors into consideration in future development and implementation of carbon emission reduction policies and related health education campaigns.

Dimension Reduction of Multivariable Optical Emission Spectrometer Datasets for Industrial Plasma Processes

PubMed Central

Yang, Jie; McArdle, Conor; Daniels, Stephen

2014-01-01

A new data dimension-reduction method, called Internal Information Redundancy Reduction (IIRR), is proposed for application to Optical Emission Spectroscopy (OES) datasets obtained from industrial plasma processes. For example in a semiconductor manufacturing environment, real-time spectral emission data is potentially very useful for inferring information about critical process parameters such as wafer etch rates, however, the relationship between the spectral sensor data gathered over the duration of an etching process step and the target process output parameters is complex. OES sensor data has high dimensionality (fine wavelength resolution is required in spectral emission measurements in order to capture data on all chemical species involved in plasma reactions) and full spectrum samples are taken at frequent time points, so that dynamic process changes can be captured. To maximise the utility of the gathered dataset, it is essential that information redundancy is minimised, but with the important requirement that the resulting reduced dataset remains in a form that is amenable to direct interpretation of the physical process. To meet this requirement and to achieve a high reduction in dimension with little information loss, the IIRR method proposed in this paper operates directly in the original variable space, identifying peak wavelength emissions and the correlative relationships between them. A new statistic, Mean Determination Ratio (MDR), is proposed to quantify the information loss after dimension reduction and the effectiveness of IIRR is demonstrated using an actual semiconductor manufacturing dataset. As an example of the application of IIRR in process monitoring/control, we also show how etch rates can be accurately predicted from IIRR dimension-reduced spectral data. PMID:24451453

Changes in inorganic fine particulate matter sensitivities to precursors due to large-scale US emissions reductions.

PubMed

Holt, Jareth; Selin, Noelle E; Solomon, Susan

2015-04-21

We examined the impact of large US emissions changes, similar to those estimated to have occurred between 2005 and 2012 (high and low emissions cases, respectively), on inorganic PM2.5 sensitivities to further NOx, SO2, and NH3 emissions reductions using the chemical transport model GEOS-Chem. Sensitivities to SO2 emissions are larger year-round and across the US in the low emissions case than the high emissions case due to more aqueous-phase SO2 oxidation. Sensitivities to winter NOx emissions are larger in the low emissions case, more than 2× those of the high emissions case in parts of the northern Midwest. Sensitivities to NH3 emissions are smaller (∼40%) in the low emissions case, year-round, and across the US. Differences in NOx and NH3 sensitivities indicate an altered atmospheric acidity. Larger sensitivities to SO2 and NOx in the low emissions case imply that reducing these emissions may improve air quality more now than they would have in 2005; conversely, NH3 reductions may not improve air quality as much as previously assumed.

A mathematical/physics carbon emission reduction strategy for building supply chain network based on carbon tax policy

NASA Astrophysics Data System (ADS)

Li, Xueying; Peng, Ying; Zhang, Jing

2017-03-01

Under the background of a low carbon economy, this paper examines the impact of carbon tax policy on supply chain network emission reduction. The integer linear programming method is used to establish a supply chain network emission reduction such a model considers the cost of CO2 emissions, and analyses the impact of different carbon price on cost and carbon emissions in supply chains. The results show that the implementation of a carbon tax policy can reduce CO2 emissions in building supply chain, but the increase in carbon price does not produce a reduction effect, and may bring financial burden to the enterprise. This paper presents a reasonable carbon price range and provides decision makers with strategies towards realizing a low carbon building supply chain in an economical manner.

Emission reductions from woody biomass waste for energy as an alternative to open burning.

PubMed

Springsteen, Bruce; Christofk, Tom; Eubanks, Steve; Mason, Tad; Clavin, Chris; Storey, Brett

2011-01-01

Woody biomass waste is generated throughout California from forest management, hazardous fuel reduction, and agricultural operations. Open pile burning in the vicinity of generation is frequently the only economic disposal option. A framework is developed to quantify air emissions reductions for projects that alternatively utilize biomass waste as fuel for energy production. A demonstration project was conducted involving the grinding and 97-km one-way transport of 6096 bone-dry metric tons (BDT) of mixed conifer forest slash in the Sierra Nevada foothills for use as fuel in a biomass power cogeneration facility. Compared with the traditional open pile burning method of disposal for the forest harvest slash, utilization of the slash for fuel reduced particulate matter (PM) emissions by 98% (6 kg PM/BDT biomass), nitrogen oxides (NOx) by 54% (1.6 kg NOx/BDT), nonmethane volatile organics (NMOCs) by 99% (4.7 kg NMOCs/BDT), carbon monoxide (CO) by 97% (58 kg CO/BDT), and carbon dioxide equivalents (CO2e) by 17% (0.38 t CO2e/BDT). Emission contributions from biomass processing and transport operations are negligible. CO2e benefits are dependent on the emission characteristics of the displaced marginal electricity supply. Monetization of emissions reductions will assist with fuel sourcing activities and the conduct of biomass energy projects.

Impact of Biogenic Emission Uncertainties on the Simulated Response of Ozone and Fine Particulate Matter to Anthropogenic Emission Reductions

PubMed Central

Hogrefe, Christian; Isukapalli, Sastry S.; Tang, Xiaogang; Georgopoulos, Panos G.; He, Shan; Zalewsky, Eric E.; Hao, Winston; Ku, Jia-Yeong; Key, Tonalee; Sistla, Gopal

2011-01-01

The role of emissions of volatile organic compounds and nitric oxide from biogenic sources is becoming increasingly important in regulatory air quality modeling as levels of anthropogenic emissions continue to decrease and stricter health-based air quality standards are being adopted. However, considerable uncertainties still exist in the current estimation methodologies for biogenic emissions. The impact of these uncertainties on ozone and fine particulate matter (PM2.5) levels for the eastern United States was studied, focusing on biogenic emissions estimates from two commonly used biogenic emission models, the Model of Emissions of Gases and Aerosols from Nature (MEGAN) and the Biogenic Emissions Inventory System (BEIS). Photochemical grid modeling simulations were performed for two scenarios: one reflecting present day conditions and the other reflecting a hypothetical future year with reductions in emissions of anthropogenic oxides of nitrogen (NOx). For ozone, the use of MEGAN emissions resulted in a higher ozone response to hypothetical anthropogenic NOx emission reductions compared with BEIS. Applying the current U.S. Environmental Protection Agency guidance on regulatory air quality modeling in conjunction with typical maximum ozone concentrations, the differences in estimated future year ozone design values (DVF) stemming from differences in biogenic emissions estimates were on the order of 4 parts per billion (ppb), corresponding to approximately 5% of the daily maximum 8-hr ozone National Ambient Air Quality Standard (NAAQS) of 75 ppb. For PM2.5, the differences were 0.1–0.25 μg/m3 in the summer total organic mass component of DVFs, corresponding to approximately 1–2% of the value of the annual PM2.5 NAAQS of 15 μg/m3. Spatial variations in the ozone and PM2.5 differences also reveal that the impacts of different biogenic emission estimates on ozone and PM2.5 levels are dependent on ambient levels of anthropogenic emissions. PMID:21305893

Electricity generation: options for reduction in carbon emissions.

PubMed

Whittington, H W

2002-08-15

Historically, the bulk production of electricity has been achieved by burning fossil fuels, with unavoidable gaseous emissions, including large quantities of carbon dioxide: an average-sized modern coal-burning power station is responsible for more than 10 Mt of CO(2) each year. This paper details typical emissions from present-day power stations and discusses the options for their reduction. Acknowledging that the cuts achieved in the past decade in the UK CO(2) emissions have been achieved largely by fuel switching, the remaining possibilities offered by this method are discussed. Switching to less-polluting fossil fuels will achieve some measure of reduction, but the basic problem of CO(2) emissions continues. Of the alternatives to fossil fuels, only nuclear power represents a zero-carbon large-scale energy source. Unfortunately, public concerns over safety and radioactive waste have still to be assuaged. Other approaches include the application of improved combustion technology, the removal of harmful gases from power-station flues and the use of waste heat to improve overall power-station efficiency. These all have a part to play, but many consider our best hope for emissions reduction to be the use of renewable energy. The main renewable energy contenders are assessed in this paper and realistic estimates of the contribution that each could provide are indicated. It appears that, in the time-scale envisaged by planners for reduction in CO(2) emission, in many countries renewable energy will be unlikely to deliver. At the same time, it is worth commenting that, again in many countries, the level of penetration of renewable energy will fall short of the present somewhat optimistic targets. Of renewable options, wind energy could be used in the short to medium term to cover for thermal plant closures, but for wind energy to be successful, the network will have to be modified to cope with wind's intermittent nature. Globally, hydroelectricity is currently the

10 CFR 300.12 - Acceptance of reports and registration of entity emission reductions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Acceptance of reports and registration of entity emission reductions. 300.12 Section 300.12 Energy DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.12 Acceptance of reports and registration of entity emission...

10 CFR 300.12 - Acceptance of reports and registration of entity emission reductions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Acceptance of reports and registration of entity emission reductions. 300.12 Section 300.12 Energy DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.12 Acceptance of reports and registration of entity emission...

10 CFR 300.12 - Acceptance of reports and registration of entity emission reductions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Acceptance of reports and registration of entity emission reductions. 300.12 Section 300.12 Energy DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.12 Acceptance of reports and registration of entity emission...

10 CFR 300.12 - Acceptance of reports and registration of entity emission reductions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Acceptance of reports and registration of entity emission reductions. 300.12 Section 300.12 Energy DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.12 Acceptance of reports and registration of entity emission...

10 CFR 300.12 - Acceptance of reports and registration of entity emission reductions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Acceptance of reports and registration of entity emission reductions. 300.12 Section 300.12 Energy DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.12 Acceptance of reports and registration of entity emission...

Exhaust emissions reduction for intermittent combustion aircraft engines

NASA Technical Reports Server (NTRS)

Rezy, B. J.; Stuckas, K. J.; Tucker, J. R.; Meyers, J. E.

1982-01-01

Three concepts which, to an aircraft piston engine, provide reductions in exhaust emissions of hydrocarbons and carbon monoxide while simultaneously improving fuel economy. The three chosen concepts, (1) an improved fuel injection system, (2) an improved cooling cylinder head, and (3) exhaust air injection, when combined, show a synergistic relationship in achieving these goals. In addition, the benefits of variable ignition timing were explored and both dynamometer and flight testing of the final engine configuration were accomplished.

[Energy Conservation and Emissions Reduction Benefits Analysis for Battery Electric Buses Based on Travel Services].

PubMed

Lin, Xiao-dan; Tian, Liang; Lü, Bin; Yang, Jian-xin

2015-09-01

Battery Electric Bus (BEB) has become one of prior options of urban buses for its "zero emission" during the driving stage. However, the environmental performance of electric buses is affected by multi-factors from the point of whole life cycle. In practice, carrying capacity of BEB and power generation structures can both implement evident effects on the energy consumption and pollutants emission of BEB. Therefore, take the above factors into consideration, in this article, Life Cycle Assessment is employed to evaluate the energy conservation and emissions reduction benefits of BEB. Results indicate that, travel service is more reasonable as the functional unit, rather than mileage, since the carrying capacity of BEB is 15% lower than the diesel buses. Moreover, compared with diesel buses, the energy conservation and emissions reduction benefits of battery electric buses are all different due to different regional power structures. Specifically, the energy benefits are 7. 84%, 11. 91%, 26. 90%, 11. 15%, 19. 55% and 20. 31% respectively in Huabei, Huadong, Huazhong, Dongbei, Xibei and Nanfang power structure. From the point of comprehensive emissions reduction benefits, there is no benefit in Huabei power structure, as it depends heavily on coal. But in other areas, the comprehensive emissions reduction benefits of BEB are separately 3. 46%, 26. 81%, 1. 17%, 13. 74% and 17. 48% in Huadong, Huazhong, Dongbei, Xibei and Nanfang. Therefore, it suggests that, enlargement of carrying capacity should be taken as the most prior technology innovation direction for BEB, and the grids power structure should be taken into consideration when the development of BEB is in planning.

Real-world energy use and emission rates for idling long-haul trucks and selected idle reduction technologies.

PubMed

Frey, H Christopher; Kuo, Po-Yao

2009-07-01

Long-haul freight trucks typically idle for 2000 or more hours per year, motivating interest in reducing idle fuel use and emissions using auxiliary power units (APUs) and shore-power (SP). Fuel-use rates are estimated based on electronic control unit (ECU) data for truck engines and measurements for APU engines. Engine emission factors were measured using a portable emission measurement system. Indirect emissions from SP were based on average utility grid emission factors. Base engine fuel use and APU and SP electrical load were analyzed for 20 trucks monitored for more than 1 yr during 2.76 million mi of activity within 42 U.S. states. The average base engine fuel use varied from 0.46 to 0.65 gal/hr. The average APU fuel use varied from 0.24 to 0.41 gal/hr. Fuel-use rates are typically lowest in mild weather, highest in hot or cold weather, and depend on engine speed (revolutions per minute [RPM]). Compared with the base engine, APU fuel use and emissions of carbon dioxide (CO2) and sulfur dioxide (SO2) are lower by 36-47%. Oxides of nitrogen (NO(x)) emissions are lower by 80-90%. Reductions in particulate matter (PM), carbon monoxide (CO), and hydrocarbon emissions vary from approximately 10 to over 50%. SP leads to more substantial reductions, except for SO2. The actual achievable reductions will be lower because only a fraction of base engine usage will be replaced by APUs, SP, or both. Recommendations are made for reducing base engine fuel use and emissions, accounting for variability in fuel use and emissions reductions, and further work to quantify real-world avoided fuel use and emissions.

Assessment of methods for methyl iodide emission reduction and pest control using a simulation model

NASA Astrophysics Data System (ADS)

Luo, Lifang; Ashworth, Daniel J.; Šimunek, Jirka; Xuan, Richeng; Yates, Scott R.

2013-02-01

The increasing registration of the fumigant methyl iodide within the USA has led to more concerns about its toxicity to workers and bystanders. Emission mitigation strategies are needed to protect the public and environmental health while providing effective pest control. The effectiveness of various methods on emissions reduction and pest control was assessed using a process-based mathematical model in this study. Firstly, comparisons between the simulated and laboratory measured emission fluxes and cumulative emissions were made for methyl iodide (MeI) under four emission reduction treatments: 1) control, 2) using soil with high organic matter content (HOM), 3) being covered by virtually impermeable film (VIF), and 4) irrigating soil surface following fumigation (Irrigation). Then the model was extended to simulate a broader range of emission reduction strategies for MeI, including 5) being covered by high density polyethylene (HDPE), 6) increasing injection depth from 30 cm to 46 cm (Deep), 7) HDPE + Deep, 8) adding a reagent at soil surface (Reagent), 9) Reagent + Irrigation, and 10) Reagent + HDPE. Furthermore, the survivability of three types of soil-borne pests (citrus nematodes [Tylenchulus semipenetrans], barnyard seeds [Echinochloa crus-galli], fungi [Fusarium oxysporum]) was also estimated for each scenario. Overall, the trend of the measured emission fluxes as well as total emission were reasonably reproduced by the model for treatments 1 through 4. Based on the numerical simulation, the ranking of effectiveness in total emission reduction was VIF (82.4%) > Reagent + HDPE (73.2%) > Reagent + Irrigation (43.0%) > Reagent (23.5%) > Deep + HDPE (19.3%) > HOM (17.6%) > Deep (13.0%) > Irrigation (11.9%) > HDPE (5.8%). The order for pest control efficacy suggests, VIF had the highest pest control efficacy, followed by Deep + HDPE, Irrigation, Reagent + Irrigation, HDPE, Deep, Reagent + HDPE, Reagent, and HOM. Therefore, VIF is the optimal method disregarding

[Efficiency of industrial energy conservation and carbon emission reduction in Liaoning Pro-vince based on data envelopment analysis (DEA)method.

PubMed

Wang, Li; Xi, Feng Ming; Li, Jin Xin; Liu, Li Li

2016-09-01

Taking 39 industries as independent decision-making units in Liaoning Province from 2003 to 2012 and considering the benefits of energy, economy and environment, we combined direction distance function and radial DEA method to estimate and decompose the energy conservation and carbon emissions reduction efficiency of the industries. Carbon emission of each industry was calculated and defined as an undesirable output into the model of energy saving and carbon emission reduction efficiency. The results showed that energy saving and carbon emission reduction efficiency of industries had obvious heterogeneity in Liaoning Province. The whole energy conservation and carbon emissions reduction efficiency in each industry of Liaoning Province was not high, but it presented a rising trend. Improvements of pure technical efficiency and scale efficiency were the main measures to enhance energy saving and carbon emission reduction efficiency, especially scale efficiency improvement. In order to improve the energy saving and carbon emission reduction efficiency of each industry in Liaoning Province, we put forward that Liaoning Province should adjust industry structure, encourage the development of low carbon high benefit industries, improve scientific and technological level and adjust the industry scale reasonably, meanwhile, optimize energy structure, and develop renewable and clean energy.

Results and status of the NASA aircraft engine emission reduction technology programs

NASA Technical Reports Server (NTRS)

Jones, R. E.; Diehl, L. A.; Petrash, D. A.; Grobman, J.

1978-01-01

The results of an aircraft engine emission reduction study are reviewed in detail. The capability of combustor concepts to produce significantly lower levels of exhaust emissions than present production combustors was evaluated. The development status of each combustor concept is discussed relative to its potential for implementation in aircraft engines. Also, the ability of these combustor concepts to achieve proposed NME and NCE EPA standards is discussed.

Projects to Improve Air Quality at Ports – 2014 Diesel Emissions Reduction Act (DERA) Funding Opportunity - Closed Announcement FY 2014

EPA Pesticide Factsheets

OTAQ is soliciting proposals that achieve reductions in diesel emissions produced by diesel engines and diesel emissions exposure, from fleets operating at marine and inland water ports under the Diesel Emissions Reduction Act (DERA).

Projects to Improve Air Quality at Ports – 2013 Diesel Emissions Reduction Act (DERA) Funding Opportunity - Closed Announcement FY 2014

EPA Pesticide Factsheets

OTAQ is soliciting proposals that achieve reductions in diesel emissions produced by diesel engines and diesel emissions exposure, from fleets operating at marine and inland water ports under the Diesel Emissions Reduction Act (DERA).

Reconciling NOx emissions reductions and ozone trends in ...

EPA Pesticide Factsheets

Dynamic evaluation seeks to assess the ability of photochemical models to replicate changes in air quality as emissions and other conditions change. When a model fails to replicate an observed change, a key challenge is to discern whether the discrepancy is caused by errors in meteorological simulations, errors in emission magnitudes and changes, or inaccurate responses of simulated pollutant concentrations to emission changes. In this study, the Community Multiscale Air Quality (CMAQ) model is applied to simulate the ozone (O3) change after the NOx SIP Call and mobile emission controls substantially reduced nitrogen oxides (NOx) emissions in the eastern U.S. from 2002 to 2006. For both modeled and observed O3, changes in episode average daily maximal 8-h O3 were highly correlated (R2 = 0.89) with changes in the 95th percentile, although the magnitudes of reductions increased nonlinearly at high percentile O3 concentrations. Observed downward changes in mean NOx (−11.6 to −2.5 ppb) and 8-h O3 (−10.4 to −4.7 ppb) concentrations in metropolitan areas in the NOx SIP Call region were under-predicted by 31%–64% and 26%–66%, respectively. The under-predicted O3 improvements in the NOx SIP Call region could not be explained by adjusting for temperature biases in the meteorological input, or by considering uncertainties in the chemical reaction rate constants. However, the under-prediction in O3 improvements could be alleviated by 5%–31% by constraining NO

Collaborative Emission Reduction Model Based on Multi-Objective Optimization for Greenhouse Gases and Air Pollutants.

PubMed

Meng, Qing-chun; Rong, Xiao-xia; Zhang, Yi-min; Wan, Xiao-le; Liu, Yuan-yuan; Wang, Yu-zhi

2016-01-01

CO2 emission influences not only global climate change but also international economic and political situations. Thus, reducing the emission of CO2, a major greenhouse gas, has become a major issue in China and around the world as regards preserving the environmental ecology. Energy consumption from coal, oil, and natural gas is primarily responsible for the production of greenhouse gases and air pollutants such as SO2 and NOX, which are the main air pollutants in China. In this study, a mathematical multi-objective optimization method was adopted to analyze the collaborative emission reduction of three kinds of gases on the basis of their common restraints in different ways of energy consumption to develop an economic, clean, and efficient scheme for energy distribution. The first part introduces the background research, the collaborative emission reduction for three kinds of gases, the multi-objective optimization, the main mathematical modeling, and the optimization method. The second part discusses the four mathematical tools utilized in this study, which include the Granger causality test to analyze the causality between air quality and pollutant emission, a function analysis to determine the quantitative relation between energy consumption and pollutant emission, a multi-objective optimization to set up the collaborative optimization model that considers energy consumption, and an optimality condition analysis for the multi-objective optimization model to design the optimal-pole algorithm and obtain an efficient collaborative reduction scheme. In the empirical analysis, the data of pollutant emission and final consumption of energies of Tianjin in 1996-2012 was employed to verify the effectiveness of the model and analyze the efficient solution and the corresponding dominant set. In the last part, several suggestions for collaborative reduction are recommended and the drawn conclusions are stated.

Collaborative Emission Reduction Model Based on Multi-Objective Optimization for Greenhouse Gases and Air Pollutants

PubMed Central

Zhang, Yi-min; Wan, Xiao-le; Liu, Yuan-yuan; Wang, Yu-zhi

2016-01-01

CO2 emission influences not only global climate change but also international economic and political situations. Thus, reducing the emission of CO2, a major greenhouse gas, has become a major issue in China and around the world as regards preserving the environmental ecology. Energy consumption from coal, oil, and natural gas is primarily responsible for the production of greenhouse gases and air pollutants such as SO2 and NOX, which are the main air pollutants in China. In this study, a mathematical multi-objective optimization method was adopted to analyze the collaborative emission reduction of three kinds of gases on the basis of their common restraints in different ways of energy consumption to develop an economic, clean, and efficient scheme for energy distribution. The first part introduces the background research, the collaborative emission reduction for three kinds of gases, the multi-objective optimization, the main mathematical modeling, and the optimization method. The second part discusses the four mathematical tools utilized in this study, which include the Granger causality test to analyze the causality between air quality and pollutant emission, a function analysis to determine the quantitative relation between energy consumption and pollutant emission, a multi-objective optimization to set up the collaborative optimization model that considers energy consumption, and an optimality condition analysis for the multi-objective optimization model to design the optimal-pole algorithm and obtain an efficient collaborative reduction scheme. In the empirical analysis, the data of pollutant emission and final consumption of energies of Tianjin in 1996–2012 was employed to verify the effectiveness of the model and analyze the efficient solution and the corresponding dominant set. In the last part, several suggestions for collaborative reduction are recommended and the drawn conclusions are stated. PMID:27010658

Guidance for Halon Emissions Reduction Rule (40 CFR Part 82, Subpart H)

EPA Pesticide Factsheets

Document provides guidance for technicians on compliance with EPA's halon emission reduction rule (40 CFR 82, Subpart H). Guidance covers technician training requirements and proper halon disposal and recycling.

Field Emission Enhancement and the Field-Screening Effect Reduction using Carbon Nanopipettes as Cold Cathodes

NASA Astrophysics Data System (ADS)

Safir, Abdelilah; Mudd, David; Yazdanpanah, Mehdi; Dobrokhotov, Vladimir; Sumanasekera, Gamini; Cohn, Robert

2008-03-01

In this work, we report a recent experimental study of high emission current densities exceeding 10mA/cm^2 and breakdown electric field lower than 5Volts/μm from novel cold cathodes such as conical shaped carbon nanopipettes (CNP). CNP were grown by CVD on Pt wire and have apex as sharp as 10nm with length between 3-6μm. The emission experiments were conducted under vacuum in a scanning electron microscope for individual CNP and in a dedicated chamber for bulk samples. CNP's conical bases and low density contribute significantly to the reduction of the screening effect and to the field emission enhancement. The experimental value for the field enhancement factor, γ, was about 867. Comparing emission results taken from CNP and aligned multiwall carbon nanotubes (MWNT) show that the ratio between γCNP and γMWNT is ˜1.6 which contributes to the reduction of screening effect. The emission from multilayers of graphene was also studied. High emission current (20μA) demonstrates promising emission properties of graphene.

Primary Aluminum Reduction Industry - National Emission Standards for Hazardous Air Pollutants (NESHAP)

EPA Pesticide Factsheets

National emission standards for each new or existing potline, paste production operation, and anode bake furnace associated with a primary aluminum reduction plant. Includes rule history, implementation information and additional resources.

Regional Attribution of Ozone Production and Associated Radiative Forcing: a Step to Crediting NOx Emission Reductions

NASA Astrophysics Data System (ADS)

Naik, V.; Mauzerall, D. L.; Horowitz, L.; Schwarzkopf, D.; Ramaswamy, V.; Oppenheimer, M.

2004-12-01

The global distribution of tropospheric ozone (O3) depends on the location of emissions of its precursors in addition to chemical and dynamical factors. The global picture of O3 forcing is, therefore, a sum of regional forcings arising from emissions of precursors from different sources. The Kyoto Protocol does not include ozone as a greenhouse gas, and emission reductions of ozone precursors made under Kyoto or any similar agreement would presently receive no credit. In this study, we quantitatively estimate the contribution of emissions of nitrogen oxides (NOx), the primary limiting O3 precursor in the non-urban atmosphere, from specific countries and regions of the world to global O3 concentration distributions. We then estimate radiative forcing resulting from the regional perturbations of NOx emissions. This analysis is intended as an early step towards incorporating O3 into the Kyoto Protocol or any successor agreement. Under such a system countries could obtain credit for improvements in local air quality that result in reductions of O3 concentrations because of the associated reductions in radiative forcing. We use the global chemistry transport model, MOZART-2, to simulate the global O3 distribution for base year 1990 and perturbations to this distribution caused by a 10% percent reduction in the base emissions of NOx from the United States, Europe, East Asia, India, South America, and Africa. We calculate the radiative forcing for the simulated base and perturbed O3 distributions using the GFDL radiative transfer model. The difference between the radiative forcing from O3 for the base and perturbed distributions provides an estimate of the marginal radiative forcing from a region's emissions of NOx. We will present a quantitative analysis of the magnitude, spatial, and temporal distribution of radiative forcing resulting from marginal changes in the NOx emissions from each region.

Status of NASA aircraft engine emission reduction and upper atmosphere measurement programs

NASA Technical Reports Server (NTRS)

Rudey, R. A.; Lezberg, E. A.

1976-01-01

Advanced emission reduction techniques for five existing aircraft gas turbine engines are evaluated. Progress made toward meeting the 1979 EPA standards in rig tests of combustors for the five engines is reported. Results of fundamental combustion studies suggest the possibility of a new generation of jet engine combustor technology that would reduce oxides-of-nitrogen (NOx) emissions far below levels currently demonstrated in the engine-related programs. The Global Air Sampling Program (GAS) is now in full operation and is providing data on constituent measurements of ozone and other minor upper-atmosphere species related to aircraft emissions.

Greenhouse gas and criteria emission benefits through reduction of vessel speed at sea.

PubMed

Khan, M Yusuf; Agrawal, Harshit; Ranganathan, Sindhuja; Welch, William A; Miller, J Wayne; Cocker, David R

2012-11-20

Reducing emissions from ocean-going vessels (OGVs) as they sail near populated areas is a widely recognized goal, and Vessel Speed Reduction (VSR) is one of several strategies that is being adopted by regulators and port authorities. The goal of this research was to measure the emission benefits associated with greenhouse gas and criteria pollutants by operating OGVs at reduced speed. Emissions were measured from one Panamax and one post-Panamax class container vessels as their vessel speed was reduced from cruise to 15 knots or below. VSR to 12 knots yielded carbon dioxide (CO(2)) and nitrogen oxides (NO(x)) emissions reductions (in kg/nautical mile (kg/nmi)) of approximately 61% and 56%, respectively, as compared to vessel cruise speed. The mass emission rate (kg/nmi) of PM(2.5) was reduced by 69% with VSR to 12 knots alone and by ~97% when coupled with the use of the marine gas oil (MGO) with 0.00065% sulfur content. Emissions data from vessels while operating at sea are scarce and measurements from this research demonstrated that tidal current is a significant parameter affecting emission factors (EFs) at lower engine loads. Emissions factors at ≤20% loads calculated by methodology adopted by regulatory agencies were found to underestimate PM(2.5) and NO(x) by 72% and 51%, respectively, when compared to EFs measured in this study. Total pollutant emitted (TPE) in the emission control area (ECA) was calculated, and emission benefits were estimated as the VSR zone increased from 24 to 200 nmi. TPE(CO2) and TPE(PM2.5) estimated for large container vessels showed benefits for CO(2) (2-26%) and PM(2.5) (4-57%) on reducing speeds from 15 to 12 knots, whereas TPE(CO2) and TPE(PM2.5) for small and medium container vessels were similar at 15 and 12 knots.

Achieving Realistic Energy and Greenhouse Gas Emission Reductions in U.S. Cities

NASA Astrophysics Data System (ADS)

Blackhurst, Michael F.

2011-12-01

In recognizing that energy markets and greenhouse gas emissions are significantly influences by local factors, this research examines opportunities for achieving realistic energy greenhouse gas emissions from U.S. cities through provisions of more sustainable infrastructure. Greenhouse gas reduction opportunities are examined through the lens of a public program administrator charged with reducing emissions given realistic financial constraints and authority over emissions reductions and energy use. Opportunities are evaluated with respect to traditional public policy metrics, such as benefit-cost analysis, net benefit analysis, and cost-effectiveness. Section 2 summarizes current practices used to estimate greenhouse gas emissions from communities. I identify improved and alternative emissions inventory techniques such as disaggregating the sectors reported, reporting inventory uncertainty, and aligning inventories with local organizations that could facilitate emissions mitigation. The potential advantages and challenges of supplementing inventories with comparative benchmarks are also discussed. Finally, I highlight the need to integrate growth (population and economic) and business as usual implications (such as changes to electricity supply grids) into climate action planning. I demonstrate how these techniques could improve decision making when planning reductions, help communities set meaningful emission reduction targets, and facilitate CAP implementation and progress monitoring. Section 3 evaluates the costs and benefits of building energy efficiency are estimated as a means of reducing greenhouse gas emissions in Pittsburgh, PA and Austin, TX. Two policy objectives were evaluated: maximize GHG reductions given initial budget constraints or maximize social savings given target GHG reductions. This approach explicitly evaluates the trade-offs between three primary and often conflicting program design parameters: initial capital constraints, social savings

The "Universal" in UHC and Ghana's National Health Insurance Scheme: policy and implementation challenges and dilemmas of a lower middle income country.

PubMed

Agyepong, Irene Akua; Abankwah, Daniel Nana Yaw; Abroso, Angela; Chun, ChangBae; Dodoo, Joseph Nii Otoe; Lee, Shinye; Mensah, Sylvester A; Musah, Mariam; Twum, Adwoa; Oh, Juwhan; Park, Jinha; Yang, DoogHoon; Yoon, Kijong; Otoo, Nathaniel; Asenso-Boadi, Francis

2016-09-21

Despite universal population coverage and equity being a stated policy goal of its NHIS, over a decade since passage of the first law in 2003, Ghana continues to struggle with how to attain it. The predominantly (about 70 %) tax funded NHIS currently has active enrolment hovering around 40 % of the population. This study explored in-depth enablers and barriers to enrolment in the NHIS to provide lessons and insights for Ghana and other low and middle income countries (LMIC) into attaining the goal of universality in Universal Health Coverage (UHC). We conducted a cross sectional mixed methods study of an urban and a rural district in one region of Southern Ghana. Data came from document review, analysis of routine data on enrolment, key informant in-depth interviews with local government, regional and district insurance scheme and provider staff and community member in-depth interviews and focus group discussions. Population coverage in the NHIS in the study districts was not growing towards near universal because of failure of many of those who had ever enrolled to regularly renew annually as required by the NHIS policy. Factors facilitating and enabling enrolment were driven by the design details of the scheme that emanate from national level policy and program formulation, frontline purchaser and provider staff implementation arrangements and contextual factors. The factors inter-related and worked together to affect client experience of the scheme, which were not always the same as the declared policy intent. This then also affected the decision to enrol and stay enrolled. UHC policy and program design needs to be such that enrolment is effectively compulsory in practice. It also requires careful attention and responsiveness to actual and potential subscriber, purchaser and provider (stakeholder) incentives and related behaviour generated at implementation levels.

Hydrocarbon emissions from in-use commercial aircraft during airport operations.

PubMed

Herndon, Scott C; Rogers, Todd; Dunlea, Edward J; Jayne, John T; Miake-Lye, Richard; Knighton, Berk

2006-07-15

The emissions of selected hydrocarbons from in-use commercial aircraft at a major airport in the United States were characterized using proton-transfer reaction mass spectrometry (PTR-MS) and tunable infrared differential absorption spectroscopy (TILDAS) to probe the composition of diluted exhaust plumes downwind. The emission indices for formaldehyde, acetaldehyde, benzene, and toluene, as well as other hydrocarbon species, were determined through analysis of 45 intercepted plumes identified as being associated with specific aircraft. As would have been predicted for high bypass turbine engines, the hydrocarbon emission index was greater in idle and taxiway acceleration plumes relative to approach and takeoff plumes. The opposite was seen in total NOy emission index, which increased from idle to takeoff. Within the idle plumes sampled in this study, the median emission index for formaldehyde was 1.1 g of HCHO per kg of fuel. For the subset of hydrocarbons measured in this work, the idle emissions levels relative to formaldehyde agree well with those of previous studies. The projected total unburned hydrocarbons (UHC) deduced from the range of in-use idle plumes analyzed in this work is greater than a plausible range of engine types using the defined idle condition (7% of rated engine thrust) in the International Civil Aviation Organization (ICAO) databank reference.

U.S. sulfur dioxide emission reductions: Shifting factors and a carbon dioxide penalty

DOE PAGES

Brown, Marilyn Ann; Li, Yufei; Massetti, Emanuele; ...

2017-01-18

For more than 20 years, the large-scale application of flue gas desulfurization technology has been a dominant cause of SO 2 emission reductions. From 1994–2004, electricity generation from coal increased, but the shift to low-sulfur coal eclipsed this. From 2004–2014, electricity generation from coal decreased, but a shift to higher-sulfur subbituminous and lignite coal overshadowed this. Here, the shift in coal quality has also created a CO 2 emissions penalty, representing 2% of the sector’s total emissions in 2014.

Deep Reductions in Greenhouse Gas Emissions from the California Transportation Sector: Dynamics in Vehicle Fleet and Energy Supply Transitions to Achieve 80% Reduction in Emissions from 1990 Levels by 2050

NASA Astrophysics Data System (ADS)

Leighty, Wayne Waterman

California's "80in50" target for reducing greenhouse gas emissions to 80 percent below 1990 levels by the year 2050 is based on climate science rather than technical feasibility of mitigation. As such, it raises four fundamental questions: is this magnitude of reduction in greenhouse gas emissions possible, what energy system transitions over the next 40 years are necessary, can intermediate policy goals be met on the pathway toward 2050, and does the path of transition matter for the objective of climate change mitigation? Scenarios for meeting the 80in50 goal in the transportation sector are modelled. Specifically, earlier work defining low carbon transport scenarios for the year 2050 is refined by incorporating new information about biofuel supply. Then transition paths for meeting 80in50 scenarios are modelled for the light-duty vehicle sub-sector, with important implications for the timing of action, rate of change, and cumulative greenhouse gas emissions. One aspect of these transitions -- development in the California wind industry to supply low-carbon electricity for plug-in electric vehicles -- is examined in detail. In general, the range of feasible scenarios for meeting the 80in50 target is narrow enough that several common themes are apparent: electrification of light-duty vehicles must occur; continued improvements in vehicle efficiency must be applied to improving fuel economy; and energy carriers must de-carbonize to less than half of the carbon intensity of gasoline and diesel. Reaching the 80in50 goal will require broad success in travel demand reduction, fuel economy improvements and low-carbon fuel supply, since there is little opportunity to increase emission reductions in one area if we experience failure in another. Although six scenarios for meeting the 80in50 target are defined, only one also meets the intermediate target of reducing greenhouse gas emissions to 1990 levels by the year 2020. Furthermore, the transition path taken to reach any

Atmospheric pollution reduction effect and regional predicament: An empirical analysis based on the Chinese provincial NOx emissions.

PubMed

Ding, Lei; Liu, Chao; Chen, Kunlun; Huang, Yalin; Diao, Beidi

2017-07-01

Atmospheric pollution emissions have become a matter of public concern in recent years. However, most of the existing researches on NOx pollution are from the natural science and technology perspective, few studies have been conducted from an economic point, and regional differences have not been given adequate attention. This paper adopts provincial panel data from 2006 to 2013 and the LMDI model to analyze the key driving factors and regional dilemmas of NOx emissions. The results show that significant regional disparities still exit on NO x emissions and its reduction effect 27 provinces didn't accomplish their corresponding reduction targets. Economic development factor is the dominating driving factor of NO x emissions during the study period, while energy efficiency and technology improvement factors offset total NO x emissions in the majority of provinces. In addition, the industrial structure factor plays a more significant role in reducing the NO x emissions after 2011. Therefore, the government should consider all these factors as well as regional heterogeneity in developing appropriate pollution mitigating policies. It's necessary to change NOx emissions control attitude from original key areas control to divided-zone control, not only attaches great importance to the reduction of the original key areas, but also emphasizes the new potential hotspots with high NO x emissions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mitigation of methane emissions in cities: How new measurements and partnerships can contribute to emissions reduction strategies

DOE PAGES

Hopkins, Francesca M.; Ehleringer, James R.; Bush, Susan E.; ...

2016-09-10

Cities generate 70% of anthropogenic greenhouse gas emissions, a fraction that is grow-ing with global urbanization. While cities play an important role in climate change mitigation, there has been little focus on reducing urban methane (CH4) emissions. Here, we develop a conceptual framework for CH 4 mitigation in cities by describing emission processes, the role of measurements, and a need for new institutional partnerships. Urban CH 4 emissions are likely to grow with expanding use of natural gas and organic waste disposal systems in growing population centers; however, we currently lack the ability to quantify this increase. We also lackmore » systematic knowledge of the relative contribution of these distinct source sectors on emissions. We present new observations from four North American cities to demonstrate that CH4 emissions vary in magnitude and sector from city to city and hence require different mitigation strategies. Detections of fugitive emissions from these systems suggest that current mitiga- tion approaches are absent or ineffective. These findings illustrate that tackling urban CH 4 emissions will require research efforts to identify mitigation targets, develop and implement new mitigation strategies, and monitor atmospheric CH 4 levels to ensure the success of mitigation efforts. This research will require a variety of techniques to achieve these objectives and should be deployed in cities globally. In conclusion, we suggest that metropolitan scale partnerships may effectively coordinate systematic measurements and actions focused on emission reduction goals.« less

Mitigation of methane emissions in cities: How new measurements and partnerships can contribute to emissions reduction strategies

NASA Astrophysics Data System (ADS)

Hopkins, Francesca M.; Ehleringer, James R.; Bush, Susan E.; Duren, Riley M.; Miller, Charles E.; Lai, Chun-Ta; Hsu, Ying-Kuang; Carranza, Valerie; Randerson, James T.

2016-09-01

Cities generate 70% of anthropogenic greenhouse gas emissions, a fraction that is growing with global urbanization. While cities play an important role in climate change mitigation, there has been little focus on reducing urban methane (CH4) emissions. Here, we develop a conceptual framework for CH4 mitigation in cities by describing emission processes, the role of measurements, and a need for new institutional partnerships. Urban CH4 emissions are likely to grow with expanding use of natural gas and organic waste disposal systems in growing population centers; however, we currently lack the ability to quantify this increase. We also lack systematic knowledge of the relative contribution of these distinct source sectors on emissions. We present new observations from four North American cities to demonstrate that CH4 emissions vary in magnitude and sector from city to city and hence require different mitigation strategies. Detections of fugitive emissions from these systems suggest that current mitigation approaches are absent or ineffective. These findings illustrate that tackling urban CH4 emissions will require research efforts to identify mitigation targets, develop and implement new mitigation strategies, and monitor atmospheric CH4 levels to ensure the success of mitigation efforts. This research will require a variety of techniques to achieve these objectives and should be deployed in cities globally. We suggest that metropolitan scale partnerships may effectively coordinate systematic measurements and actions focused on emission reduction goals.

Mitigation of methane emissions in cities: How new measurements and partnerships can contribute to emissions reduction strategies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hopkins, Francesca M.; Ehleringer, James R.; Bush, Susan E.

Cities generate 70% of anthropogenic greenhouse gas emissions, a fraction that is grow-ing with global urbanization. While cities play an important role in climate change mitigation, there has been little focus on reducing urban methane (CH4) emissions. Here, we develop a conceptual framework for CH 4 mitigation in cities by describing emission processes, the role of measurements, and a need for new institutional partnerships. Urban CH 4 emissions are likely to grow with expanding use of natural gas and organic waste disposal systems in growing population centers; however, we currently lack the ability to quantify this increase. We also lackmore » systematic knowledge of the relative contribution of these distinct source sectors on emissions. We present new observations from four North American cities to demonstrate that CH4 emissions vary in magnitude and sector from city to city and hence require different mitigation strategies. Detections of fugitive emissions from these systems suggest that current mitiga- tion approaches are absent or ineffective. These findings illustrate that tackling urban CH 4 emissions will require research efforts to identify mitigation targets, develop and implement new mitigation strategies, and monitor atmospheric CH 4 levels to ensure the success of mitigation efforts. This research will require a variety of techniques to achieve these objectives and should be deployed in cities globally. In conclusion, we suggest that metropolitan scale partnerships may effectively coordinate systematic measurements and actions focused on emission reduction goals.« less

Incorporating Voluntary Mobile Source Emission Reduction Programs in State Implementation Plans (SIPs)

EPA Pesticide Factsheets

This EPA memorandum provides guidance and sets forth policy and interpretation regarding the granting of explicit State Implementation Plan (SIP) credit for Voluntary Mobile Source Emission Reduction Programs (VMEPs) under section 110 of the Clean Air Act.

Assessment of methods for methyl iodide emission reduction and pest control using a simulation model

USDA-ARS?s Scientific Manuscript database

Various methods have been developed to reduce atmospheric emissions from the agricultural use of highly volatile pesticides and mitigate their adverse environmental effects. The effectiveness of various methods on emissions reduction and pest control was assessed using simulation model in this study...

Limited emission reductions from fuel subsidy removal except in energy-exporting regions.

PubMed

Jewell, Jessica; McCollum, David; Emmerling, Johannes; Bertram, Christoph; Gernaat, David E H J; Krey, Volker; Paroussos, Leonidas; Berger, Loïc; Fragkiadakis, Kostas; Keppo, Ilkka; Saadi, Nawfal; Tavoni, Massimo; van Vuuren, Detlef; Vinichenko, Vadim; Riahi, Keywan

2018-02-07

Hopes are high that removing fossil fuel subsidies could help to mitigate climate change by discouraging inefficient energy consumption and levelling the playing field for renewable energy. In September 2016, the G20 countries re-affirmed their 2009 commitment (at the G20 Leaders' Summit) to phase out fossil fuel subsidies and many national governments are using today's low oil prices as an opportunity to do so. In practical terms, this means abandoning policies that decrease the price of fossil fuels and electricity generated from fossil fuels to below normal market prices. However, whether the removal of subsidies, even if implemented worldwide, would have a large impact on climate change mitigation has not been systematically explored. Here we show that removing fossil fuel subsidies would have an unexpectedly small impact on global energy demand and carbon dioxide emissions and would not increase renewable energy use by 2030. Subsidy removal would reduce the carbon price necessary to stabilize greenhouse gas concentration at 550 parts per million by only 2-12 per cent under low oil prices. Removing subsidies in most regions would deliver smaller emission reductions than the Paris Agreement (2015) climate pledges and in some regions global subsidy removal may actually lead to an increase in emissions, owing to either coal replacing subsidized oil and natural gas or natural-gas use shifting from subsidizing, energy-exporting regions to non-subsidizing, importing regions. Our results show that subsidy removal would result in the largest CO 2 emission reductions in high-income oil- and gas-exporting regions, where the reductions would exceed the climate pledges of these regions and where subsidy removal would affect fewer people living below the poverty line than in lower-income regions.

Limited emission reductions from fuel subsidy removal except in energy-exporting regions

NASA Astrophysics Data System (ADS)

Jewell, Jessica; McCollum, David; Emmerling, Johannes; Bertram, Christoph; Gernaat, David E. H. J.; Krey, Volker; Paroussos, Leonidas; Berger, Loïc; Fragkiadakis, Kostas; Keppo, Ilkka; Saadi, Nawfal; Tavoni, Massimo; van Vuuren, Detlef; Vinichenko, Vadim; Riahi, Keywan

2018-02-01

Hopes are high that removing fossil fuel subsidies could help to mitigate climate change by discouraging inefficient energy consumption and levelling the playing field for renewable energy. In September 2016, the G20 countries re-affirmed their 2009 commitment (at the G20 Leaders’ Summit) to phase out fossil fuel subsidies and many national governments are using today’s low oil prices as an opportunity to do so. In practical terms, this means abandoning policies that decrease the price of fossil fuels and electricity generated from fossil fuels to below normal market prices. However, whether the removal of subsidies, even if implemented worldwide, would have a large impact on climate change mitigation has not been systematically explored. Here we show that removing fossil fuel subsidies would have an unexpectedly small impact on global energy demand and carbon dioxide emissions and would not increase renewable energy use by 2030. Subsidy removal would reduce the carbon price necessary to stabilize greenhouse gas concentration at 550 parts per million by only 2-12 per cent under low oil prices. Removing subsidies in most regions would deliver smaller emission reductions than the Paris Agreement (2015) climate pledges and in some regions global subsidy removal may actually lead to an increase in emissions, owing to either coal replacing subsidized oil and natural gas or natural-gas use shifting from subsidizing, energy-exporting regions to non-subsidizing, importing regions. Our results show that subsidy removal would result in the largest CO2 emission reductions in high-income oil- and gas-exporting regions, where the reductions would exceed the climate pledges of these regions and where subsidy removal would affect fewer people living below the poverty line than in lower-income regions.

THE IMPACT OF WINTER NH3 EMISSION REDUCTIONS ON INORGANIC PARTICULATE MATTER UNDER PRESENT AND FUTURE REGULATED CONDITIONS

EPA Science Inventory

Recent regulation by the US Environmental Protection Agency requires large-scale emission reductions of NO_x and SO₂. This study estimates the impact of these changes on the sensitivity of PM_2.5 to NH₃ emission reductions and the reduce...

Effect of power plant emission reductions on a nearby wilderness area: a case study in northwestern Colorado

USGS Publications Warehouse

Mast, M. Alisa; Ely, Daniel

2013-01-01

This study evaluates the effect of emission reductions at two coal-fired power plants in northwestern Colorado on a nearby wilderness area. Control equipment was installed at both plants during 1999–2004 to reduce SO2 and NOx emissions. One challenge was separating the effects of local from regional emissions, which also declined during the study period. The long-term datasets examined confirm that emission reductions had a beneficial effect on air and water quality in the wilderness. Despite a 75 % reduction in SO2 emissions, sulfate aerosols measured in the wilderness decreased by only 20 %. Because the site is relatively close to the power plants (2 to sulfate, particularly under conditions of low relative humidity, might account for this less than one-to-one response. On the clearest days, emissions controls appeared to improve visibility by about 1 deciview, which is a small but perceptible improvement. On the haziest days, however, there was little improvement perhaps reflecting the dominance of regional haze and other components of visibility degradation particularly organic carbon and dust. Sulfate and acidity in atmospheric deposition decreased by 50 % near the southern end of the wilderness of which 60 % was attributed to power plant controls and the remainder to reductions in regional sources. Lake water sulfate responded rapidly to trends in deposition declining at 28 lakes monitored in and near the wilderness. Although no change in the acid–base status was observed, few of the lakes appear to be at risk from chronic or episodic acidification.

Assessment of emission scenarios for 2030 and impacts of black carbon emission reduction measures on air quality and radiative forcing in Southeast Asia

NASA Astrophysics Data System (ADS)

Agustian Permadi, Didin; Oanh, Nguyen Thi Kim; Vautard, Robert

2018-03-01

Our previously published paper (Permadi et al. 2018) focused on the preparation of emission input data and evaluation of WRF-CHIMERE performance in 2007. This paper details the impact assessment of the future (2030) black carbon (BC) emission reduction measures for Southeast Asia (SEA) countries on air quality, health and BC direct radiative forcing (DRF). The business as usual (BAU2030) projected emissions from the base year of 2007 (BY2007), assuming no intervention with the linear projection of the emissions based on the past activity data for Indonesia and Thailand and the sectoral GDP growth for other countries. The RED2030 featured measures to cut down emissions in major four source sectors in Indonesia and Thailand (road transport, residential cooking, industry, biomass open burning) while for other countries the Representative Concentration Pathway 8.5 (RCP8.5) emissions were assumed. WRF-CHIMERE simulated levels of aerosol species under BAU2030 and RED2030 for the modeling domain using the base year meteorology and 2030 boundary conditions from LMDZ-INCA. The extended aerosol optical depth module (AODEM) calculated the total columnar AOD and BC AOD for all scenarios with an assumption on the internal mixing state. Under RED2030, the health benefits were analyzed in terms of the number of avoided premature deaths associated with ambient PM2.5 reduction along with BC DRF reduction. Under BAU2030, the average number of the premature deaths per 100 000 people in the SEA domain would increase by 30 from BY2007 while under RED2030 the premature deaths would be cut down (avoided) by 63 from RED2030. In 2007, the maximum annual average BC DRF in the SEA countries was 0.98 W m-2, which would increase to 2.0 W m-2 under BAU2030 and 1.4 W m-2 under RED2030. Substantial impacts on human health and BC DRF reduction in SEA could result from the emission measures incorporated in RED2030. Future works should consider other impacts, such as for agricultural crop

Technical analysis on energy conservation and emission reduction of new energy electric vehicle in China

NASA Astrophysics Data System (ADS)

Zheng, Chaocheng

2017-10-01

With the global environmental problems and energy crisis continuously emerging, all countries are taking active measures to achieve the benign development of domestic economy and society. Vehicle, as a large oil consumption and emissions of carbon dioxide, nend to be a revolutionary change. Therefore, the development of new energy electric vehicle has become the consensus of the world. On this background, this paper has sorted out the current state and the related development planning of new energy electric vehicles in different countries to predict the car ownership of the new energy electric vehicles using elastic coefficient method and setting different path of development, conclude that under the consideration of energy conservation and emissions reduction factors, our country should mainly promote the BEV to realize the maximum energy conservation and emissions reduction.

Strategies for emission reduction of air pollutants produced from a chemical plant.

PubMed

Lee, Byeong-Kyu; Cho, Sung-Woong

2003-01-01

Various air pollution control (APC) techniques were employed in order to reduce emissions of air pollutants produced from chemical plants, which have many different chemical production facilities. For an emission reduction of acid gases, this study employed a method to improve solubility of pollutants by decreasing the operating temperature of the scrubbers, increasing the surface area for effective contact of gas and liquid, and modifying processes in the acid scrubbers. To reduce emission of both amines and acid gases, pollutant gas components were first separated, then condensation and/or acid scrubbing, depending on the chemical and physical properties of pollutant components, were used. To reduce emission of solvents, condensation and activated carbon adsorption were employed. To reduce emission of a mixture gases containing acid gases and solvents, the mixed gases were passed into the first condenser, the acid scrubber, the second condenser, and the activated carbon adsorption tower in sequence. As a strategy to reduce emission of pollutants at the source, this study also employed the simple pollution prevention concept of modification of the previously operating APC control device. Finally, air emissions of pollutants produced from the chemical plants were much more reduced by applying proper APC methods, depending upon the types (physical or chemical properties) and the specific emission situations of pollutants.

Assessing Regional Emissions Reductions from Travel Efficiency: Applying the Travel Efficiency Assessment Method

EPA Pesticide Factsheets

This presentation from the 2016 TRB Summer Conference on Transportation Planning and Air Quality summarizes the application of the Travel Efficiency Assessment Method (TEAM) which analyzed selected transportation emission reduction strategies in three case

The role of anthropogenic aerosol emission reduction in achieving the Paris Agreement's objective

NASA Astrophysics Data System (ADS)

Hienola, Anca; Pietikäinen, Joni-Pekka; O'Donnell, Declan; Partanen, Antti-Ilari; Korhonen, Hannele; Laaksonen, Ari

2017-04-01

The Paris agreement reached in December 2015 under the auspices of the United Nation Framework Convention on Climate Change (UNFCCC) aims at holding the global temperature increase to well below 2◦C above preindustrial levels and "to pursue efforts to limit the temperature increase to 1.5◦C above preindustrial levels". Limiting warming to any level implies that the total amount of carbon dioxide (CO2) - the dominant driver of long-term temperatures - that can ever be emitted into the atmosphere is finite. Essentially, this means that global CO2 emissions need to become net zero. CO2 is not the only pollutant causing warming, although it is the most persistent. Short-lived, non-CO2 climate forcers also must also be considered. Whereas much effort has been put into defining a threshold for temperature increase and zero net carbon emissions, surprisingly little attention has been paid to the non-CO2 climate forcers, including not just the non-CO2 greenhouse gases (methane (CH4), nitrous oxide (N2O), halocarbons etc.) but also the anthropogenic aerosols like black carbon (BC), organic carbon (OC) and sulfate. This study investigates the possibility of limiting the temperature increase to 1.5◦C by the end of the century under different future scenarios of anthropogenic aerosol emissions simulated with the very simplistic MAGICC climate carbon cycle model as well as with ECHAM6.1-HAM2.2-SALSA + UVic ESCM. The simulations include two different CO2 scenarios- RCP3PD as control and a CO2 reduction leading to 1.5◦C (which translates into reaching the net zero CO2 emissions by mid 2040s followed by negative emissions by the end of the century); each CO2 scenario includes also two aerosol pollution control cases denoted with CLE (current legislation) and MFR (maximum feasible reduction). The main result of the above scenarios is that the stronger the anthropogenic aerosol emission reduction is, the more significant the temperature increase by 2100 relative to pre

The Production, Value, and Reduction Responsibility of Carbon Emissions through Electricity Consumption of Manufacturing Industries in South Korea and Thailand

NASA Astrophysics Data System (ADS)

Kitikun, Medhawin

This dissertation provides a new method of measuring efforts by manufacturing industries to reduce their emissions by curtailing electricity consumption. Employing comprehensive firm-level data from the National Manufacture Annual Surveys of South Korea and Thailand, I construct the measure from estimates of revenue functions by industry. The data consists of firms from more than 20 industries in each year from 1982 to 2005 for Korea and from 2001 to 2008 for Thailand. With a total of more than two million observations, I estimate revenue functions for each industry and year. Here, I use three inputs: number of employees(L), fixed asset stock(K), and electricity consumption(E) and two types of functional forms to represent each industry's revenue function. Second, under market competitive condition, I find that profit maximizing firms deviated their level of electricity usage in production from the profit-maximizing level during the time period for both countries, and I develop a theoretical framework to explain this behavior. Then, I tested the theory using my empirical models. Results support the notion of a hidden environmental value expressed by firms in the form of voluntary deviations from profit-maximizing levels of input demand. The measure used is the gap between the marginal revenue product of electricity and its price. This gap should increase with income, consistent with the Environmental Kuznets Curve literature. My current model provides considerable support for this proposition. Estimates indicate, in most industries, a negative relationship between per-capita income and emissions. In the final section of the dissertation, I consider the equitable distribution of emissions reduction burden under an international agreement such as the reduction effort, Kyoto Protocol. Both developed and developing countries have to cut their emissions to a specific reduction percentage target. Domestically, I present two extreme scenarios. In the first scenario

Assessing "dangerous climate change": required reduction of carbon emissions to protect young people, future generations and nature.

PubMed

Hansen, James; Kharecha, Pushker; Sato, Makiko; Masson-Delmotte, Valerie; Ackerman, Frank; Beerling, David J; Hearty, Paul J; Hoegh-Guldberg, Ove; Hsu, Shi-Ling; Parmesan, Camille; Rockstrom, Johan; Rohling, Eelco J; Sachs, Jeffrey; Smith, Pete; Steffen, Konrad; Van Susteren, Lise; von Schuckmann, Karina; Zachos, James C

2013-01-01

We assess climate impacts of global warming using ongoing observations and paleoclimate data. We use Earth's measured energy imbalance, paleoclimate data, and simple representations of the global carbon cycle and temperature to define emission reductions needed to stabilize climate and avoid potentially disastrous impacts on today's young people, future generations, and nature. A cumulative industrial-era limit of ∼500 GtC fossil fuel emissions and 100 GtC storage in the biosphere and soil would keep climate close to the Holocene range to which humanity and other species are adapted. Cumulative emissions of ∼1000 GtC, sometimes associated with 2°C global warming, would spur "slow" feedbacks and eventual warming of 3-4°C with disastrous consequences. Rapid emissions reduction is required to restore Earth's energy balance and avoid ocean heat uptake that would practically guarantee irreversible effects. Continuation of high fossil fuel emissions, given current knowledge of the consequences, would be an act of extraordinary witting intergenerational injustice. Responsible policymaking requires a rising price on carbon emissions that would preclude emissions from most remaining coal and unconventional fossil fuels and phase down emissions from conventional fossil fuels.

Assessing 'Dangerous Climate Change': Required Reduction of Carbon Emissions to Protect Young People, Future Generations and Nature

NASA Technical Reports Server (NTRS)

Hansen, James; Kharecha, Pushker; Sato, Makiko; Masson-Demotte, Valerie; Ackerman, Frank; Beerling, David J.; Hearty, Paul J.; Hoegh-Guldberg, Ove; Hsu, Shi-Ling; Parmesan, Camille;

Energy-Efficiency and Air-Pollutant Emissions-Reduction Opportunities for the Ammonia Industry in China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Ding; Hasanbeigi, Ali; Chen, Wenying

As one of the most energy-intensive and polluting industries, ammonia production is responsible for significant carbon dioxide (CO 2) and air-pollutant emissions. Although many energy-efficiency measures have been proposed by the Chinese government to mitigate greenhouse gas emissions and improve air quality, lack of understanding of the cost-effectiveness of such improvements has been a barrier to implementing these measures. Assessing the costs, benefits, and cost-effectiveness of different energy-efficiency measures is essential to advancing this understanding. In this study, a bottom-up energy conservation supply curve model is developed to estimate the potential for energy savings and emissions reductions from 26 energy-efficiencymore » measures that could be applied in China’s ammonia industry. Cost-effective implementation of these measures saves a potential 271.5 petajoules/year for fuel and 5,443 gigawatt-hours/year for electricity, equal to 14% of fuel and 14% of electricity consumed in China’s ammonia industry in 2012. These reductions could mitigate 26.7 million tonnes of CO 2 emissions. This study also quantifies the co-benefits of reducing air-pollutant emissions and water use that would result from saving energy in China’s ammonia industry. This quantitative analysis advances our understanding of the cost-effectiveness of energy-efficiency measures and can be used to augment efforts to reduce energy use and environmental impacts.« less

Optimization of Power Generation Rights Under the Requirements of Energy Conservation and Emission Reduction

NASA Astrophysics Data System (ADS)

Hu-ping, YANY; Chong-wei, ZHONG; Fei-fei, YAN; Cheng-yi, TANG

2018-03-01

In recent years, the energy crisis and greenhouse effect problem have caused wide public concern, if these issues cannot be resolved quickly, they will bring troubles to people’s lives.In response, many countries around the world have implemented policies to reduce energy consumption and greenhouse gas emissions. In our country, the electric power industry has made great contribution to the daily life of people and the development of industry, but it is also an industry of high consumption and high emission.In order to realize the sustainable development of society, it is necessary to make energy conservation and emission reduction in the power industry as an important part of the realization of this goal.In this context, power generation trade has become a hot topic in energy conservation and emission reduction.Through the electricity consumption of the units with different power efficiency and coal consumption rate,it can achieve the target of reducing coal consumption, reducing network loss, reducing greenhouse gas emission, and increasing social benefit,and so on. This article put forward a optimal energy model on the basis of guaranteeing safety and environmental protection.In this paper, they used the IEEE30, IEEE39, IEEE57 and IEEE118 node system as an example, and set up the control groups to prove the practicality of the presented model.The solving method of this model was interior-point method.

Carbon Emission Reduction with Capital Constraint under Greening Financing and Cost Sharing Contract.

PubMed

Qin, Juanjuan; Zhao, Yuhui; Xia, Liangjie

2018-04-13

Motivated by the industrial practices, this work explores the carbon emission reductions for the manufacturer, while taking into account the capital constraint and the cap-and-trade regulation. To alleviate the capital constraint, two contracts are analyzed: greening financing and cost sharing. We use the Stackelberg game to model four cases as follows: (1) in Case A1, the manufacturer has no greening financing and no cost sharing; (2) in Case A2, the manufacturer has greening financing, but no cost sharing; (3) in Case B1, the manufacturer has no greening financing but has cost sharing; and, (4) in Case B2, the manufacturer has greening financing and cost sharing. Then, using the backward induction method, we derive and compare the equilibrium decisions and profits of the participants in the four cases. We find that the interest rate of green finance does not always negatively affect the carbon emission reduction of the manufacturer. Meanwhile, the cost sharing from the retailer does not always positively affect the carbon emission reduction of the manufacturer. When the cost sharing is low, both of the participants' profits in Case B1 (under no greening finance) are not less than that in Case B2 (under greening finance). When the cost sharing is high, both of the participants' profits in Case B1 (under no greening finance) are less than that in Case B2 (under greening finance).

Carbon Emission Reduction with Capital Constraint under Greening Financing and Cost Sharing Contract

PubMed Central

Qin, Juanjuan; Zhao, Yuhui; Xia, Liangjie

2018-01-01

Motivated by the industrial practices, this work explores the carbon emission reductions for the manufacturer, while taking into account the capital constraint and the cap-and-trade regulation. To alleviate the capital constraint, two contracts are analyzed: greening financing and cost sharing. We use the Stackelberg game to model four cases as follows: (1) in Case A1, the manufacturer has no greening financing and no cost sharing; (2) in Case A2, the manufacturer has greening financing, but no cost sharing; (3) in Case B1, the manufacturer has no greening financing but has cost sharing; and, (4) in Case B2, the manufacturer has greening financing and cost sharing. Then, using the backward induction method, we derive and compare the equilibrium decisions and profits of the participants in the four cases. We find that the interest rate of green finance does not always negatively affect the carbon emission reduction of the manufacturer. Meanwhile, the cost sharing from the retailer does not always positively affect the carbon emission reduction of the manufacturer. When the cost sharing is low, both of the participants’ profits in Case B1 (under no greening finance) are not less than that in Case B2 (under greening finance). When the cost sharing is high, both of the participants’ profits in Case B1 (under no greening finance) are less than that in Case B2 (under greening finance). PMID:29652859

Continuous reduction of cyclic adsorbed and desorbed NO(x) in diesel emission using nonthermal plasma.

PubMed

Kuwahara, Takuya; Nakaguchi, Harunobu; Kuroki, Tomoyuki; Okubo, Masaaki

2016-05-05

Considering the recent stringent regulations governing diesel NO(x) emission, an aftertreatment system for the reduction of NO(x) in the exhaust gas has been proposed and studied. The proposed system is a hybrid method combining nonthermal plasma and NOx adsorbent. The system does not require precious metal catalysts or harmful chemicals such as urea and ammonia. In the present system, NO(x) in diesel emission is treated by adsorption and desorption by adsorbent as well as nonthermal plasma reduction. In addition, the remaining NO(x) in the adsorbent is desorbed again in the supplied air by residual heat. The desorbed NO(x) in air recirculates into the intake of the engine, and this process, i.e., exhaust gas components' recirculation (EGCR) achieves NO(x) reduction. Alternate utilization of two adsorption chambers in the system can achieve high-efficiency NO(x) removal continuously. An experiment with a stationary diesel engine for electric power generation demonstrates an energy efficiency of 154 g(NO2)/kWh for NO(x) removal and continuous NO(x) reduction of 70.3%. Considering the regulation against diesel emission in Japan, i.e., the new regulation to be imposed on vehicles of 3.5-7.5 ton since 2016, the present aftertreatment system fulfills the requirement with only 1.0% of engine power. Copyright © 2016. Published by Elsevier B.V.

Detection from space of a reduction in anthropogenic emissions of nitrogen oxides during the Chinese economic downturn

NASA Astrophysics Data System (ADS)

Lin, J.-T.; McElroy, M. B.

2011-01-01

Rapid economic and industrial development in China and relatively weak emission controls have resulted in significant increases in emissions of nitrogen oxides (NOx) in recent years, with the exception of late 2008 to mid 2009 when the economic downturn led to emission reductions detectable from space. Here vertical column densities (VCDs) of tropospheric NO2 retrieved from satellite observations by SCIAMACHY, GOME-2 and OMI (both by KNMI and by NASA) are used to evaluate changes in emissions of NOx from October 2004 to February 2010 identifying impacts of the economic downturn. Data over polluted regions of Northern East China suggest an increase of 27-33% in annual mean VCD of NO2 prior to the downturn, consistent with an increase of 49% in thermal power generation (TPG) reflecting the economic growth. More detailed analysis is used to quantify changes in emissions of NOx in January over the period 2005-2010 when the effect of the downturn was most evident. The GEOS-Chem model is employed to evaluate the effect of changes in chemistry and meteorology on VCD of NO2. This analysis indicates that emissions decreased by 20% from January 2008 to January 2009, close to the reduction of 18% in TPG that occurred over the same interval. A combination of three relatively independent approaches indicates that the economic downturn was responsible for a~reduction in emissions by 9-11% in January 2009 with an additional decrease of 10% attributed to the slow-down in industrial activity associated with the coincident celebration of the Chinese New Year.

The impacts of electricity dispatch protocols on the emission reductions due to wind power and carbon tax.

PubMed

Yu, Yang; Rajagopal, Ram

2015-02-17

Two dispatch protocols have been adopted by electricity markets to deal with the uncertainty of wind power but the effects of the selection between the dispatch protocols have not been comprehensively analyzed. We establish a framework to compare the impacts of adopting different dispatch protocols on the efficacy of using wind power and implementing a carbon tax to reduce emissions. We suggest that a market has high potential to achieve greater emission reduction by adopting the stochastic dispatch protocol instead of the static protocol when the wind energy in the market is highly uncertain or the market has enough adjustable generators, such as gas-fired combustion generators. Furthermore, the carbon-tax policy is more cost-efficient for reducing CO2 emission when the market operates according to the stochastic protocol rather than the static protocol. An empirical study, which is calibrated according to the data from the Electric Reliability Council of Texas market, confirms that using wind energy in the Texas market results in a 12% CO2 emission reduction when the market uses the stochastic dispatch protocol instead of the 8% emission reduction associated with the static protocol. In addition, if a 6$/ton carbon tax is implemented in the Texas market operated according to the stochastic protocol, the CO2 emission is similar to the emission level from the same market with a 16$/ton carbon tax operated according to the static protocol. Correspondingly, the 16$/ton carbon tax associated with the static protocol costs 42.6% more than the 6$/ton carbon tax associated with the stochastic protocol.

[Discussion on reduction potential of CH4 emission intensity for early off-take practice of grazing yak].

PubMed

Wang, Shi-Ping; Wilkes, Andreas; Wang, Ya-Yun; Bai, Ling

2014-08-01

The case study preliminarily compared the CH4 reduction potential and CH4 emission intensity of 7 year-old and 4 year-old grazing yak after early off-take practice based on the 2006 IPCC GHG inventory guidelines and under the premise of equal herbage consumption. Our results showed that the total CH4 emission was greater by about 86.3 kg for 2.1 4-year yaks compared with 7 years old yak during their life assuming that their total herbage consumption was the same, because total herbage consumption for a 7-year yak was equal to that of 2.1 4-year yaks. However, CH4 emission per unit body weight (1.374 kg x kg(-1)) for a 7-year yak (i. e. emission intensity) was higher than that of 2.1 4-year yaks (0.973 kg x kg(-1)) because total body weight of 2.1 4-year yaks was higher by 192 kg than that of a 7-year yak. According to CH4 emission intensity, change of the early off-take practice from 7-year to 4-year yak could reduce 77 kg CH4 if producing 192 kg body weight through 2.1 4-year yaks compared with a 7-year yak, i. e. reduction potential was about 1 600 kg CO2 equivalent under the same consuming forage. Therefore, for grassland-based animal husbandry, early off-take practice for grazing animals had a great reduction potential in the intensity of greenhouse gases (GHGs) emissions per unit output rather than total emissions of GHGs.

Study on emission characteristics and reduction strategy of nitrous oxide during wastewater treatment by different processes.

PubMed

Sun, Shichang; Bao, Zhiyuan; Sun, Dezhi

2015-03-01

Given the inexorable increase in global wastewater treatment, increasing amounts of nitrous oxide are expected to be emitted from wastewater treatment plants and released to the atmosphere. It has become imperative to study the emission and control of nitrous oxide in the various wastewater treatment processes currently in use. In the present investigation, the emission characteristics and the factors affecting the release of nitrous oxide were studied via full- and pilot-scale experiments in anoxic-oxic, sequencing batch reactor and oxidation ditch processes. We propose an optimal treatment process and relative strategy for nitrous oxide reduction. Our results show that both the bio-nitrifying and bio-denitrifying treatment units in wastewater treatment plants are the predominant sites for nitrous oxide production in each process, while the aerated treatment units are the critical sources for nitrous oxide emission. Compared with the emission of nitrous oxide from the anoxic-oxic (1.37% of N-influent) and sequencing batch reactor (2.69% of N-influent) processes, much less nitrous oxide (0.25% of N-influent) is emitted from the oxidation ditch process, which we determined as the optimal wastewater treatment process for nitrous oxide reduction, given the current technologies. Nitrous oxide emissions differed with various operating parameters. Controlling the dissolved oxygen concentration at a proper level during nitrification and denitrification and enhancing the utilization rate of organic carbon in the influent for denitrification are the two critical methods for nitrous oxide reduction in the various processes considered.

Inventories and reduction scenarios of urban waste-related greenhouse gas emissions for management potential.

PubMed

Yang, Dewei; Xu, Lingxing; Gao, Xueli; Guo, Qinghai; Huang, Ning

2018-06-01

Waste-related greenhouse gas (GHG) emissions have been recognized as one of the prominent contributors to global warming. Current urban waste regulations, however, face increasing challenges from stakeholders' trade-offs and hierarchic management. A combined method, i.e., life cycle inventories and scenario analysis, was employed to investigate waste-related GHG emissions during 1995-2015 and to project future scenarios of waste-driven carbon emissions by 2050 in a pilot low carbon city, Xiamen, China. The process-based carbon analysis of waste generation (prevention and separation), transportation (collection and transfer) and disposal (treatment and recycling) shows that the main contributors of carbon emissions are associated with waste disposal processes, solid waste, the municipal sector and Xiamen Mainland. Significant spatial differences of waste-related CO 2e emissions were observed between Xiamen Island and Xiamen Mainland using the carbon intensity and density indexes. An uptrend of waste-related CO 2e emissions from 2015 to 2050 is identified in the business as usual, waste disposal optimization, waste reduction and the integrated scenario, with mean annual growth rates of 8.86%, 8.42%, 6.90% and 6.61%, respectively. The scenario and sensitivity analysis imply that effective waste-related carbon reduction requires trade-offs among alternative strategies, actions and stakeholders in a feasible plan, and emphasize a priority of waste prevention and collection in Xiamen. Our results could benefit to the future modeling of urban multiple wastes and life-cycle carbon control in similar cities within and beyond China. Copyright © 2018 Elsevier B.V. All rights reserved.

The research and application of electricity economic boom model under the constraint of energy conservation and emission reduction

NASA Astrophysics Data System (ADS)

Chen, Guangyan; Xia, Huaijian; Chen, Meiling; Wang, Dong; Jia, Sujin

2017-10-01

Energy saving and emission reduction policies affects the development of high power industry, thereby affecting electricity demand, so the study of the electricity industry boom helps to master the national economy. This paper analyses the influence of energy saving and emission reduction on power generation structure and pollutant emission in power industry. Through the construction of electricity market composite boom index to indicate electricity boom, using boom index to study volatility characteristics and trend of electricity market. Here we provide a method for the enterprise and the government, that it can infer the overall operation of the national economy situation from power data.

Effects of ferric iron reduction and regeneration on nitrous oxide and methane emissions in a rice soil.

PubMed

Huang, Bin; Yu, Kewei; Gambrell, Robert P

2009-01-01

A laboratory soil slurry experiment and an outdoor pot experiment were conducted to study effects of ferric iron (Fe(III)) reduction and regeneration on nitrous oxide (N(2)O) and methane (CH(4)) emissions in a rice (Oryza sativa L.) soil. The anoxic slurry experiment showed that enhancing microbial Fe(III) reduction by ferrihydrite amendment (40 mol Fe g(-1)) transitionally stimulated N(2)O production and lowered CH(4) production by 16% during an initial 33-day incubation. Increased regeneration of Fe(III) through a 4-day aeration period in the Fe-amended slurry compared to the control slurry reduced CH(4) emission by 30% in the subsequent 15-day anaerobic incubation. The pot experiment showed that ferrihydrite amendment (63 micromol Fe g(-1)) stimulated N(2)O fluxes in the days following flooding. The Fe amendment suppression on CH(4) emission was obscured in the early season but became significant upon reflooding in the mid- and late-seasons. As a result, seasonal CH(4) emission in Fe-amended pots was 26% lower than the control with a single 2-day drainage and 69% lower with a double 2-day drainage. The reduction in CH(4) emission upon reflooding from the Fe-amended pots was mainly attributed to the increased Fe(III) regeneration during drainage showing a mechanism of Fe(III) regeneration in mitigating CH(4) emission by short-term drainage in flooded soils.

[Reduction of meat consumption and greenhouse gas emissions associated with health benefits in Italy].

PubMed

Farchi, Sara; Lapucci, Enrica; Michelozzi, Paola

2015-01-01

the reduction in red meat consumption has been proposed as one of the climate change mitigation policies associated to health benefits. In the developed world, red meat consumption is above the recommended intake level. the aim is to evaluate health benefits, in term of mortality decline, associated to different bovine meat consumption reduction scenarios and the potential reduction in greenhouse gas (GHG) emissions. meat consumption in Italy has been estimated using the Italian National Food Consumption Survey INRAN-SCAI (2005-2006) and the Multipurpose survey on household (2012) of the Italian National Institute for Statistics. Colorectal cancer and stoke mortality data are derived from the national survey on causes of death in 2012. Bovine meat consumption risk function has been retrieved from systematic literature reviews. Mean meat consumption in Italy is equal to 770 grams/week; gender and geographical variations exist: 69 per cent of the adult population are habitual bovine meat consumers; males have an average intake of over 400 grams/week in all areas of Italy (with the exception of the South), while females have lower intakes (360 grams per week), with higher consumption in the North-West (427 gr) and lower in the South of Italy. Four scenarios of reduction of bovine meat consumption (20%, 40%, 50% e 70%, respectively) have been evaluated and the number of avoidable deaths by gender and area of residence have been estimated. GHG emissions attributed to bovine meat adult consumption have been estimated to be to 10 gigagrams CO2-eq. from low to high reduction scenario, the percentage of avoidable deaths ranged from 2.1% to 6.5% for colorectal cancer and from 1.6% to 5.6% for stroke. Health benefits were greatest for males and for people living in the North-Western regions of Italy. in Italy, in order to adhere to bovine meat consumption recommendations and to respect EU GHG emission reduction targets, scenarios between 50% and 70% need to be adopted.

Potency of energy saving and emission reduction from lighting system in residential sector of Indonesia

NASA Astrophysics Data System (ADS)

Ambarita, H.

2018-03-01

The Government of Indonesia (GoI) has a strong commitment to the target of decreasing energy intensity and reducing Greenhouse gas emissions. One of the significant solutions to reach the target is increasing energy efficiency in the lighting system in the residential sector. The objective of this paper is twofold, to estimate the potency of energy saving and emission reduction from lighting in the residential sector. Literature related to the lighting system in Indonesia has been reviewed to provide sufficient data for the estimation of the energy saving and emission reduction. The results show that the in the year 2016, a total of 95.33 TWh of nationally produced electricity is used in the residential sector. This is equal to 44% of total produced electricity. The number of costumers is 64.78 million houses. The average number of lamps and average wattage of lamps used in Indonesia are 8.35 points and 13.8 W, respectively. The number of lighting and percentage of electricity used for lighting in the residential sector in Indonesia are 20.03 TWh (21.02 %) and 497 million lamps, respectively. The projection shows that in the year 2026 the total energy for lighting and number of lamps in the residential sector are 25.05 TWh and 619 million, respectively. By promoting the present technology of high efficient lamps (LED), the potency of energy saving and emission reduction in 2026 are 2.6 TWh and 2.1 million tons CO2eq, respectively.

Energetic valorization of wood waste: estimation of the reduction in CO2 emissions.

PubMed

Vanneste, J; Van Gerven, T; Vander Putten, E; Van der Bruggen, B; Helsen, L

2011-09-01

This paper investigates the potential CO(2) emission reductions related to a partial switch from fossil fuel-based heat and electricity generation to renewable wood waste-based systems in Flanders. The results show that valorization in large-scale CHP (combined heat and power) systems and co-firing in coal plants have the largest CO(2) reduction per TJ wood waste. However, at current co-firing rates of 10%, the CO(2) reduction per GWh of electricity that can be achieved by co-firing in coal plants is five times lower than the CO(2) reduction per GWh of large-scale CHP. Moreover, analysis of the effect of government support for co-firing of wood waste in coal-fired power plants on the marginal costs of electricity generation plants reveals that the effect of the European Emission Trading Scheme (EU ETS) is effectively counterbalanced. This is due to the fact that biomass integrated gasification combined cycles (BIGCC) are not yet commercially available. An increase of the fraction of coal-based electricity in the total electricity generation from 8 to 10% at the expense of the fraction of gas-based electricity due to the government support for co-firing wood waste, would compensate entirely for the CO(2) reduction by substitution of coal by wood waste. This clearly illustrates the possibility of a 'rebound' effect on the CO(2) reduction due to government support for co-combustion of wood waste in an electricity generation system with large installed capacity of coal- and gas-based power plants, such as the Belgian one. Copyright © 2011 Elsevier B.V. All rights reserved.

Greenhouse gas emission reduction: A case study of Sri Lanka

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meier, P.; Munasinghe, M.

1995-12-31

In this paper we describe a case study for Sri Lanka that explores a wide range of options for reducing greenhouse gas (GHG) emissions. Options range from renewable technologies to carbon taxes and transportation sector initiatives. We find that setting electricity prices to reflect long-run marginal cost has a significant beneficial impact on the environment, and the expected benefits predicted on theoretical grounds are confirmed by the empirical results. Pricing reform also has a much broader impact than physical approaches to demand side management, although several options such as compact fluorescent lighting appear to have great potential. Options to reducemore » GHG emissions are limited as Sri Lanka lacks natural gas, and nuclear power is not practical until the system reaches a much larger size. Building the few remaining large hydro facilities would significantly reduce GHG emissions, but these would require costly resettlement programs. Given the inevitability for fossil-fuel base load generation, both clean coal technologies such as pressurized fluidized bed combustion, as well as steam-cycle residual oil fueled plants merit consideration as alternatives to the conventional pulverized coal-fired plants currently being considered. Transportation sector measures necessary to ameliorate local urban air pollution problems, such as vehicle inspection and maintenance programs, also bring about significant reductions of GHG emissions. 51 refs., 10 figs., 3 tabs.« less

Detection from space of a reduction in anthropogenic emissions of nitrogen oxides during the Chinese economic downturn

NASA Astrophysics Data System (ADS)

Lin, J.-T.; McElroy, M. B.

2011-08-01

Rapid economic and industrial development in China and relatively weak emission controls have resulted in significant increases in emissions of nitrogen oxides (NOx) in recent years, with the exception of late 2008 to mid 2009 when the economic downturn led to emission reductions detectable from space. Here vertical column densities (VCDs) of tropospheric NO2 retrieved from satellite observations by SCIAMACHY, GOME-2 and OMI (both by KNMI and by NASA) are used to evaluate changes in emissions of NOx from October 2004 to February 2010 identifying impacts of the economic downturn. Data over polluted regions of Northern East China suggest an increase of 27-33 % in 12-month mean VCD of NO2 prior to the downturn, consistent with an increase of 49 % in thermal power generation (TPG) reflecting the economic growth. More detailed analysis is used to quantify changes in emissions of NOx in January over the period 2005-2010 when the effect of the downturn was most evident. The GEOS-Chem model is employed to evaluate the effect of changes in chemistry and meteorology on VCD of NO2. This analysis indicates that emissions decreased by 20 % from January 2008 to January 2009, close to the reduction of 18 % in TPG that occurred over the same interval. A combination of three independent approaches indicates that the economic downturn was responsible for a reduction in emissions by 9-11 % in January 2009 with an additional decrease of 10 % attributed to the slow-down in industrial activity associated with the coincident celebration of the Chinese New Year; errors in the estimate are most likely less than 3.4 %.

Assessing “Dangerous Climate Change”: Required Reduction of Carbon Emissions to Protect Young People, Future Generations and Nature

PubMed Central

Hansen, James; Kharecha, Pushker; Sato, Makiko; Masson-Delmotte, Valerie; Ackerman, Frank; Beerling, David J.; Hearty, Paul J.; Hoegh-Guldberg, Ove; Hsu, Shi-Ling; Parmesan, Camille; Rockstrom, Johan; Rohling, Eelco J.; Sachs, Jeffrey; Smith, Pete; Steffen, Konrad; Van Susteren, Lise; von Schuckmann, Karina; Zachos, James C.

2013-01-01

We assess climate impacts of global warming using ongoing observations and paleoclimate data. We use Earth’s measured energy imbalance, paleoclimate data, and simple representations of the global carbon cycle and temperature to define emission reductions needed to stabilize climate and avoid potentially disastrous impacts on today’s young people, future generations, and nature. A cumulative industrial-era limit of ∼500 GtC fossil fuel emissions and 100 GtC storage in the biosphere and soil would keep climate close to the Holocene range to which humanity and other species are adapted. Cumulative emissions of ∼1000 GtC, sometimes associated with 2°C global warming, would spur “slow” feedbacks and eventual warming of 3–4°C with disastrous consequences. Rapid emissions reduction is required to restore Earth’s energy balance and avoid ocean heat uptake that would practically guarantee irreversible effects. Continuation of high fossil fuel emissions, given current knowledge of the consequences, would be an act of extraordinary witting intergenerational injustice. Responsible policymaking requires a rising price on carbon emissions that would preclude emissions from most remaining coal and unconventional fossil fuels and phase down emissions from conventional fossil fuels. PMID:24312568

Air quality impacts of implementing emission reduction strategies at southern California airports

NASA Astrophysics Data System (ADS)

Benosa, Guillem; Zhu, Shupeng; Kinnon, Michael Mac; Dabdub, Donald

2018-07-01

Reducing aviation emissions will be a major concern in the coming years, as the relative contribution of aviation to overall emissions is projected to increase in the future. The South Coast Air Basin of California (SoCAB) is an extreme nonattainment area with many airports located upwind of the most polluted regions in the basin. Techniques to reduce aviation emissions have been studied in the past, and strategies that can be implemented at airports include taxi-out times reduction, ground support equipment electrification and aviation biofuel implementation. These strategies have been analyzed only at the national scale, their effectiveness to improve air quality within the SoCAB given the local meteorology and chemical regimes is unclear. This work studies how the adoption of the techniques at commercial SoCAB airports affect ozone (O3) and fine particulate matter (PM2.5) concentrations. In addition, potential impacts on public exposure to PM2.5 and O3 resulting from changes in the concentration of these pollutants are estimated. In addition, the work calculates aviation emissions for each scenario and simulate the transport and atmospheric chemistry of the pollutants using the Community Multiscale Air Quality (CMAQ) model. The simultaneous application of all reduction strategies is projected to reduce the aviation-attributable population weighted ground-level PM2.5 by 36% in summer and 32% in winter. On the other hand, O3 increases by 16% in winter. Occurring mostly in densely populated areas, the decrease in ground-level PM2.5 would have a positive health impact and help the region achieve attainment of national ambient air quality standards.

Transportation Energy Futures: Combining Strategies for Deep Reductions in Energy Consumption and GHG Emissions (Brochure)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2013-03-01

This fact sheet summarizes actions in the areas of light-duty vehicle, non-light-duty vehicle, fuel, and transportation demand that show promise for deep reductions in energy use. Energy efficient transportation strategies have the potential to simultaneously reduce oil consumption and greenhouse gas (GHG) emissions. The Transportation Energy Futures (TEF) project examined how the combination of multiple strategies could achieve deep reductions in GHG emissions and petroleum use on the order of 80%. Led by NREL, in collaboration with Argonne National Laboratory, the project's primary goal was to help inform domestic decisions about transportation energy strategies, priorities, and investments, with an emphasismore » on underexplored opportunities. TEF findings reveal three strategies with the potential to displace most transportation-related petroleum use and GHG emissions: 1) Stabilizing energy use in the transportation sector through efficiency and demand-side approaches. 2) Using additional advanced biofuels. 3) Expanding electric drivetrain technologies.« less

Recent Large Reduction in Sulfur Dioxide Emissions from Chinese Power Plants Observed by the Ozone Monitoring Instrument

NASA Technical Reports Server (NTRS)

Li, Can; Zhang, Qiang; Krotkov, Nickolay A.; Streets, David G.; He, Kebin; Tsay, Si-Chee; Gleason, James F.

2010-01-01

The Ozone Monitoring Instrument (OMI) aboard NASA's Aura satellite observed substantial increases in total column SO2 and tropospheric column NO2 from 2005 to 2007, over several areas in northern China where large coal-fired power plants were built during this period. The OMI-observed SO2/NO2 ratio is consistent with the SO2/ NO2, emissions estimated from a bottom-up approach. In 2008 over the same areas, OMI detected little change in NO2, suggesting steady electricity output from the power plants. However, dramatic reductions of S0 2 emissions were observed by OMI at the same time. These reductions confirm the effectiveness of the flue-gas desulfurization (FGD) devices in reducing S02 emissions, which likely became operational between 2007 and 2008. This study further demonstrates that the satellite sensors can monitor and characterize anthropogenic emissions from large point sources.

Reduction of CO2 diffuse emissions from the traditional ceramic industry by the addition of Si-Al raw material.

PubMed

González, I; Barba-Brioso, C; Campos, P; Romero, A; Galán, E

2016-09-15

The fabrication of ceramics can produce the emission of several gases, denominated exhaust gases, and also vapours resulting from firing processes, which usually contain metals and toxic substances affecting the environment and the health of workers. Especially harmful are the diffuse emissions of CO2, fluorine, chlorine and sulphur from the ceramics industry, which, in highly industrialized areas, can suppose an important emission focus of dangerous effects. Concerning CO2, factories that use carbonate-rich raw materials (>30% carbonates) can emit high concentrations of CO2 to the atmosphere. Thus, carbonate reduction or substitution with other raw materials would reduce the emissions. In this contribution, we propose the addition of Al-shales to the carbonated ceramic materials (marls) for CO2 emission reduction, also improving the quality of the products. The employed shales are inexpensive materials of large reserves in SW-Spain. The ceramic bodies prepared with the addition of selected Al-shale to marls in variable proportions resulted in a 40%-65% CO2 emission reduction. In addition, this research underlines at the same time that the use of a low-price raw material can also contribute to obtaining products with higher added value. Copyright © 2016 Elsevier Ltd. All rights reserved.

Modeling of policies for reduction of GHG emissions in energy sector using ANN: case study-Croatia (EU).

PubMed

Bolanča, Tomislav; Strahovnik, Tomislav; Ukić, Šime; Stankov, Mirjana Novak; Rogošić, Marko

2017-07-01

This study describes the development of tool for testing different policies for reduction of greenhouse gas (GHG) emissions in energy sector using artificial neural networks (ANNs). The case study of Croatia was elaborated. Two different energy consumption scenarios were used as a base for calculations and predictions of GHG emissions: the business as usual (BAU) scenario and sustainable scenario. Both of them are based on predicted energy consumption using different growth rates; the growth rates within the second scenario resulted from the implementation of corresponding energy efficiency measures in final energy consumption and increasing share of renewable energy sources. Both ANN architecture and training methodology were optimized to produce network that was able to successfully describe the existing data and to achieve reliable prediction of emissions in a forward time sense. The BAU scenario was found to produce continuously increasing emissions of all GHGs. The sustainable scenario was found to decrease the GHG emission levels of all gases with respect to BAU. The observed decrease was attributed to the group of measures termed the reduction of final energy consumption through energy efficiency measures.

Reduction of CO2 emission by INCAM model in Malaysia biomass power plants during the year 2016.

PubMed

Amin, Nor Aishah Saidina; Talebian-Kiakalaieh, Amin

2018-03-01

As the world's second largest palm oil producer and exporter, Malaysia could capitalize on its oil palm biomass waste for power generation. The emission factors from this renewable energy source are far lower than that of fossil fuels. This study applies an integrated carbon accounting and mitigation (INCAM) model to calculate the amount of CO 2 emissions from two biomass thermal power plants. The CO 2 emissions released from biomass plants utilizing empty fruit bunch (EFB) and palm oil mill effluent (POME), as alternative fuels for powering steam and gas turbines, were determined using the INCAM model. Each section emitting CO 2 in the power plant, known as the carbon accounting center (CAC), was measured for its carbon profile (CP) and carbon index (CI). The carbon performance indicator (CPI) included electricity, fuel and water consumption, solid waste and waste-water generation. The carbon emission index (CEI) and carbon emission profile (CEP), based on the total monthly carbon production, were determined across the CPI. Various innovative strategies resulted in a 20%-90% reduction of CO 2 emissions. The implementation of reduction strategies significantly reduced the CO 2 emission levels. Based on the model, utilization of EFB and POME in the facilities could significantly reduce the CO 2 emissions and increase the potential for waste to energy initiatives. Copyright © 2017 Elsevier Ltd. All rights reserved.

Clean Air Act, TRI drive emission reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heller, K.

1994-06-22

When asked to rank priority environmental engineering projects, many chemical firms put emissions reduction first. The chief motivators are the need to comply with rules governing major sources of hazardous air pollutants (HAPS) under the Clean Air Act Amendments of 1990 (CAA), along with the need to reduce the volumes of chemicals on EPA`s Toxics Release Inventory (TRI). Deep-welling of toxics is getting special attention as the practice adds considerably to TRI numbers. {open_quotes}We want to eliminate our air toxics so that we can get entirely out of the [CAA] Maximum Achievable Control Technology (MACT) requirements,{close_quotes} says Thomas Zosel, manager/pollutionmore » prevention programs for 3M (St. Paul, MN). He estimates that 3M`s 1993 total research expenditures for environmental improvements were at least $200 million, out of an annual research budget of a little more than $1 billion. And, he says, the spending level is not expected to drop. Among its many efforts, 3M is striving to move away from solvents in all of its processes. To help reach that goal, the company developed a {open_quotes}waste measurement metric{close_quotes} that calculates the wastes produced by each of the company`s 50 operating divisions. In the case of Magic Tape, the company eliminated solvent emission by switching to a water-based adhesive that does not require a solvent.« less

Impacts of Future European Emission Reductions on Aerosol Particle Number Concentrations Accounting for Effects of Ammonia, Amines, and Organic Species.

PubMed

Julin, Jan; Murphy, Benjamin N; Patoulias, David; Fountoukis, Christos; Olenius, Tinja; Pandis, Spyros N; Riipinen, Ilona

2018-01-16

Although they are currently unregulated, atmospheric ultrafine particles (<100 nm) pose health risks because of, e.g., their capability to penetrate deep into the respiratory system. Ultrafine particles, often minor contributors to atmospheric particulate mass, typically dominate aerosol particle number concentrations. We simulated the response of particle number concentrations over Europe to recent estimates of future emission reductions of aerosol particles and their precursors. We used the chemical transport model PMCAMx-UF, with novel updates including state-of-the-art descriptions of ammonia and dimethylamine new particle formation (NPF) pathways and the condensation of organic compounds onto particles. These processes had notable impacts on atmospheric particle number concentrations. All three emission scenarios (current legislation, optimized emissions, and maximum technically feasible reductions) resulted in substantial (10-50%) decreases in median particle number concentrations over Europe. Consistent reductions were predicted in Central Europe, while Northern Europe exhibited smaller reductions or even increased concentrations. Motivated by the improved NPF descriptions for ammonia and methylamines, we placed special focus on the potential to improve air quality by reducing agricultural emissions, which are a major source of these species. Agricultural emission controls showed promise in reducing ultrafine particle number concentrations, although the change is nonlinear with particle size.

Assessment of atmospheric mercury emission reduction measures relevant for application in Poland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hlawiczka, S.; Fudala, J.

Fuel combustion for heat and power generation, together with cement production, were the most significant sources of anthropogenic atmospheric mercury emission in Poland in 2003, with 57 and 27% of Hg emission, respectively. It was found that in Poland, Hg emission reduction measures need to be focused on the energy generation sector. Sorbent injection upstream of an electrostatic precipitator or fabric filter, mercury oxidation upstream of a wet or dry flue gas desulphurisation installation, together with Hg capture on sorbents, should be considered as priority in Polish conditions. This refers mainly to fuel combustion processes but also to the productionmore » of cement. For economic reasons it seems advisable that, apart from activated carbons as sorbents, application of zeolites obtained from power plant fly ash should also be considered. Application of primary methods seems to be very promising in Polish conditions, although they should be considered rather as an additional option apart from sorbent injection as the best option. Switching from coal to liquid and gaseous fuels shows the highest potential for reducing Hg emission. For chlorine production using the mercury cell electrolysis method, strict monitoring of Hg emissions and good housekeeping of Hg releasing processes seems a promising approach, but the main activity should focus on changing mercury-based technologies into membrane cell methods. Emission abatement potential for the atmospheric mercury in Poland has been roughly assessed, showing that in perspective of 2015, the emission could be reduced to about 25% of the anthropogenic atmospheric Hg emission in 2003.« less

Reduction on NOx emissions on urban areas by changing specific vehicle fleets: effects on NO2 and O3 concentration

NASA Astrophysics Data System (ADS)

Goncalves, M.; Jimenez, P.; Baldasano, J.

2007-12-01

The largest amount of NOx emissions in urban areas comes from on-road traffic, which is the largest contributor to urban air pollution (Colvile et al., 2001). Currently different strategies are being tested in order to reduce its effects; many of them oriented to the reduction of the unitary vehicles emissions, by alternative fuels use (such as biofuels, natural gas or hydrogen) or introduction of new technologies (such as hybrid electric vehicles or fuel cells). Atmospheric modelling permits to predict their consequences on tropospheric chemistry (Vautard et al., 2007). Hence, this work assesses the changes on NO2 and O3 concentrations when substituting a 10 per cent of the urban private cars fleets by petrol hybrid electric cars (HEC) or by natural gas cars (NGC) in Madrid and Barcelona urban areas (Spain). These two cities are selected in order to highlight the different patterns of pollutants transport (inland vs. coastal city) and the different responses to emissions reductions. The results focus on a typical summertime episode of air pollution, by means of the Eulerian air quality model ARW- WRF/HERMES/CMAQ, applied with high resolution (1-hr, 1km2) since of the complexity of both areas under study. The detailed emissions scenarios are implemented in the HERMES traffic emissions module, based on the Copert III-EEA/EMEP-CORINAIR (Nztiachristos and Samaras, 2000) methodology. The HEC introduction reduces NOx emissions from on-road traffic in a 10.8 per cent and 8.2 per cent; and the NGC introduction in a 10.3 per cent and 7.8 per cent, for Madrid and Barcelona areas, respectively. The scenarios also affect the NMVOCs reduction (ranging from -3.1 to -6.9 per cent), influencing the tropospheric photochemistry through the NOx/NMVOCs ratio. The abatement of the NO photooxidation but also to the reduction on primary NO2 involves a decrease on NO2 levels centred on urban areas. For example, the NO2 24-hr average concentration in downtown areas reduces up to 8 per

The effect of future reduction in aerosol emissions on climate extremes in China

NASA Astrophysics Data System (ADS)

Wang, Zhili; Lin, Lei; Yang, Meilin; Xu, Yangyang

2016-11-01

This study investigates the effect of reduced aerosol emissions on projected temperature and precipitation extremes in China during 2031-2050 and 2081-2100 relative to present-day conditions using the daily data output from the Community Earth System Model ensemble simulations under the Representative Concentration Pathway (RCP) 8.5 with an applied aerosol reduction and RCP8.5 with fixed 2005 aerosol emissions (RCP8.5_FixA) scenarios. The reduced aerosol emissions of RCP8.5 magnify the warming effect due to greenhouse gases (GHG) and lead to significant increases in temperature extremes, such as the maximum of daily maximum temperature (TXx), minimum of daily minimum temperature (TNn), and tropical nights (TR), and precipitation extremes, such as the maximum 5-day precipitation amount, number of heavy precipitation days, and annual total precipitation from days ˃95th percentile, in China. The projected TXx, TNn, and TR averaged over China increase by 1.2 ± 0.2 °C (4.4 ± 0.2 °C), 1.3 ± 0.2 °C (4.8 ± 0.2 °C), and 8.2 ± 1.2 (30.9 ± 1.4) days, respectively, during 2031-2050 (2081-2100) under the RCP8.5_FixA scenario, whereas the corresponding values are 1.6 ± 0.1 °C (5.3 ± 0.2 °C), 1.8 ± 0.2 °C (5.6 ± 0.2 °C), and 11.9 ± 0.9 (38.4 ± 1.0) days under the RCP8.5 scenario. Nationally averaged increases in all of those extreme precipitation indices above due to the aerosol reduction account for more than 30 % of the extreme precipitation increases under the RCP8.5 scenario. Moreover, the aerosol reduction leads to decreases in frost days and consecutive dry days averaged over China. There are great regional differences in changes of climate extremes caused by the aerosol reduction. When normalized by global mean surface temperature changes, aerosols have larger effects on temperature and precipitation extremes over China than GHG.

Potential reductions in ambient NO2 concentrations from meeting diesel vehicle emissions standards

NASA Astrophysics Data System (ADS)

von Schneidemesser, Erika; Kuik, Friderike; Mar, Kathleen A.; Butler, Tim

2017-11-01

Exceedances of the concentration limit value for ambient nitrogen dioxide (NO2) at roadside sites are an issue in many cities throughout Europe. This is linked to the emissions of light duty diesel vehicles which have on-road emissions that are far greater than the regulatory standards. These exceedances have substantial implications for human health and economic loss. This study explores the possible gains in ambient air quality if light duty diesel vehicles were able to meet the regulatory standards (including both emissions standards from Europe and the United States). We use two independent methods: a measurement-based and a model-based method. The city of Berlin is used as a case study. The measurement-based method used data from 16 monitoring stations throughout the city of Berlin to estimate annual average reductions in roadside NO2 of 9.0 to 23 µg m-3 and in urban background NO2 concentrations of 1.2 to 2.7 µg m-3. These ranges account for differences in fleet composition assumptions, and the stringency of the regulatory standard. The model simulations showed reductions in urban background NO2 of 2.0 µg m-3, and at the scale of the greater Berlin area of 1.6 to 2.0 µg m-3 depending on the setup of the simulation and resolution of the model. Similar results were found for other European cities. The similarities in results using the measurement- and model-based methods support our ability to draw robust conclusions that are not dependent on the assumptions behind either methodology. The results show the significant potential for NO2 reductions if regulatory standards for light duty diesel vehicles were to be met under real-world operating conditions. Such reductions could help improve air quality by reducing NO2 exceedances in urban areas, but also have broader implications for improvements in human health and other benefits.

Contribution of cooperative sector recycling to greenhouse gas emissions reduction: A case study of Ribeirão Pires, Brazil

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Megan F., E-mail: mfking@uvic.ca; Gutberlet, Jutta, E-mail: gutber@uvic.ca

Highlights: • Cooperative recycling achieves environmental, economic and social objectives. • We calculate GHG emissions reduction for a recycling cooperative in São Paulo, Brazil. • The cooperative merits consideration as a Clean Development Mechanism (CDM) project. • A CDM project would enhance the achievements of the recycling cooperative. • National and local waste management policies support the recycling cooperative. - Abstract: Solid waste, including municipal waste and its management, is a major challenge for most cities and among the key contributors to climate change. Greenhouse gas emissions can be reduced through recovery and recycling of resources from the municipal solidmore » waste stream. In São Paulo, Brazil, recycling cooperatives play a crucial role in providing recycling services including collection, separation, cleaning, stocking, and sale of recyclable resources. The present research attempts to measure the greenhouse gas emission reductions achieved by the recycling cooperative Cooperpires, as well as highlight its socioeconomic benefits. Methods include participant observation, structured interviews, questionnaire application, and greenhouse gas accounting of recycling using a Clean Development Mechanism methodology. The results show that recycling cooperatives can achieve important energy savings and reductions in greenhouse gas emissions, and suggest there is an opportunity for Cooperpires and other similar recycling groups to participate in the carbon credit market. Based on these findings, the authors created a simple greenhouse gas accounting calculator for recyclers to estimate their emissions reductions.« less

Using oily wastewater emulsified fuel in boiler: energy saving and reduction of air pollutant emissions.

PubMed

Chen, Chun-Chi; Lee, Wen-Jhy

2008-01-01

The limited data for using emulsified oil have demonstrated its effectiveness in reducing flue gas pollutant emissions. The presence of a high concentration of toxic organic compounds in industrial wastewaters always presents significant problems. Therefore, this study was undertaken by using wastewater with COD of 9600 mg/L and total petroleum hydrocarbons-gasoline 440 mg/L for making an emulsified oil (wastewater content 20% with 0.1% surfactant) to evaluate the extent of reductions in both criteria pollutants and polycyclic aromatic hydrocarbons. For comparison, two other systems (heavy oil fuel and water-emulsified oil) were also conducted. The wastewater-emulsified oil fuel results in significant reductions in particulate matter (PM), NO(x), SO2, and CO as compared to heavy oil fuel and similar to those from water/oil emulsified fuel; for PM, it is better in wastewater-emulsified oil. The reductions of total PAH flue gas emissions are 38 and 30% for wastewater- and water-emulsified fuel, respectively; they are 63 and 44% for total BaP(eq), respectively. In addition to reducing flue gas pollutant emissions, the results also demonstrate that the use of wastewater-emulsified fuel in boiler operation provides several advantages: (1) safe disposal of industrial wastewater; and (2) energy savings of about 13%. Thus, wastewater/oil-emulsified fuel is highly suitable for use in boilers.

Contribution of cooperative sector recycling to greenhouse gas emissions reduction: a case study of Ribeirão Pires, Brazil.

PubMed

King, Megan F; Gutberlet, Jutta

2013-12-01

Solid waste, including municipal waste and its management, is a major challenge for most cities and among the key contributors to climate change. Greenhouse gas emissions can be reduced through recovery and recycling of resources from the municipal solid waste stream. In São Paulo, Brazil, recycling cooperatives play a crucial role in providing recycling services including collection, separation, cleaning, stocking, and sale of recyclable resources. The present research attempts to measure the greenhouse gas emission reductions achieved by the recycling cooperative Cooperpires, as well as highlight its socioeconomic benefits. Methods include participant observation, structured interviews, questionnaire application, and greenhouse gas accounting of recycling using a Clean Development Mechanism methodology. The results show that recycling cooperatives can achieve important energy savings and reductions in greenhouse gas emissions, and suggest there is an opportunity for Cooperpires and other similar recycling groups to participate in the carbon credit market. Based on these findings, the authors created a simple greenhouse gas accounting calculator for recyclers to estimate their emissions reductions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Combined effect of fuel-design and after-treatment system on reduction of local and global emissions from CI engine.

PubMed

Thiyagarajan, S; Geo, V Edwin; Martin, Leenus Jesu; Nagalingam, B

2018-03-22

This experimental study aims to mitigate harmful emissions from a CI engine using bio-energy with carbon capture and storage (BECCS) approach. The engine used for this experimental work is a single cylinder CI engine with a rated power of 5.2 kW at a constant speed of 1500 rpm. The BECCS approach is a combination of plant-based biofuels and carbon capture and storage (CCS) system. The whole investigation was done in four phases: (1) Substituting diesel with Karanja oil methyl ester (KOME) (2) Equal volume blending of Orange oil (ORG) with KOME (3) 20% blending of n-butanol (B) with KOME-ORG blend (4) CCS system with zeolite based non-selective catalytic reduction (NSCR) and mono ethanolamine (MEA) based selective non-catalytic reduction (SNCR) system with KOME-ORG + B20 blend. The experimental results show that substitution of diesel with KOME reduces smoke emission, but increases NO and CO 2 emission. KOME-ORG blend reduces CO 2 and smoke emissions with high NO emission due to combustion improvement. In comparison with the sole combustion of KOME at full load condition, the combination of KOME-ORG + B20 as bio-fuel with zeolite based post-combustion treatment system resulted in a maximum reduction of NO, smoke and CO 2 emission by 41%, 19% and 15% respectively.

Impact of pollutant emission reductions on summertime aerosol feedbacks: A case study over the PO valley

NASA Astrophysics Data System (ADS)

Carnevale, C.; Finzi, G.; Pederzoli, A.; Turrini, E.; Volta, M.; Ferrari, F.; Gianfreda, R.; Maffeis, G.

2015-12-01

This study presents an evaluation of the impact by future pollutant anthropogenic emission reductions on summertime aerosol feedbacks over the Po valley. The fully coupled on line model Wrf/Chem has been used to examine the air quality and meteorology response over the region to 2020 emission reductions with respect to a simulation base case (2013). Future changes in net short wave radiation flux (SW) are also analyzed. The model domain is a 6 × 6 km2 resolution grid over Northern Italy; the simulation period covers two summer months (July-August). The work is divided into two parts. In the first, model results for the Base Case simulation (BC) are evaluated by comparing Wrf/Chem output to surface observations provided by two monitoring networks. Approximately 25 sites belonging to the regional ARPA Lombardia Network are used for both chemistry (NO2, O3 and PM10 concentrations) and meteorology (wind speed and 2-meters temperature) evaluation; 4 stations part of the global AEROsol Robotic Network (AERONET) are used for the evaluation of Aerosol Optical Depth (AOD). In the second part, a Maximum Feasible Reduction (MFR) scenario at 2020 have been simulated for the same months; monthly direct, indirect and overall aerosols feedbacks for both BC and MFR have been computed and analyzed. The emission reductions in the MFR 2020 lead to a sensible change in the aerosol overall feedbacks for all variables; a drop of SW over the valley (cooling effect) is visible in both BC and MFR, but it is less significant in the MFR (-5 W m-2) compared to the BC (-45 W m-2). This difference is mainly due to the abatement of SO2 primary emissions, which leads to lower sulfates concentrations scattering radiation, thus mitigates the cooling effect and favors the warming. As SW is higher in the MFR, T2 also increases over land with respect to the BC (the cooling of -0.5 °C estimated in the Base Case almost disappears). The overall effects lead to an enhancement of PM10 concentration in

Effect of selective catalytic reduction (SCR) on fine particle emission from two coal-fired power plants in China

NASA Astrophysics Data System (ADS)

Li, Zhen; Jiang, Jingkun; Ma, Zizhen; Wang, Shuxiao; Duan, Lei

2015-11-01

Nitrogen oxides (NOx) emission abatement of coal-fired power plants (CFPPs) requires large-scaled installation of selective catalytic reduction (SCR), which would reduce secondary fine particulate matter (PM2.5) (by reducing nitrate aerosol) in the atmosphere. However, our field measurement of two CFPPs equipped with SCR indicates a significant increase of SO42- and NH4+ emission in primary PM2.5, due to catalytic enhancement of SO2 oxidation to SO3 and introducing of NH3 as reducing agent. The subsequent formation of (NH4)2SO4 or NH4HSO4 aerosol is commonly concentrated in sub-micrometer particulate matter (PM1) with a bimodal pattern. The measurement at the inlet of stack also showed doubled primary PM2.5 emission by SCR operation. This effect should therefore be considered when updating emission inventory of CFPPs. By rough estimation, the enhanced primary PM2.5 emission from CFPPs by SCR operation would offset 12% of the ambient PM2.5 concentration reduction in cities as the benefit of national NOx emission abatement, which should draw attention of policy-makers for air pollution control.

Potential benefits of solar reflective car shells: cooler cabins, fuel savings and emission reductions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levinson, Ronnen; Pan, Heng; Ban-Weiss, George

Abstract: Vehicle thermal loads and air conditioning ancillary loads are strongly influenced by the absorption of solar energy. The adoption of solar reflective coatings for opaque surfaces of the vehicle shell can decrease the ?soak? temperature of the air in the cabin of a vehicle parked in the sun, potentially reducing the vehicle?s ancillary load and improving its fuel economy by permitting the use of a smaller air conditioner. An experimental comparison of otherwise identical black and silver compact sedans indicated that increasing the solar reflectance (?) of the car?s shell by about 0.5 lowered the soak temperature of breath-levelmore » air by about 5?6?C. Thermal analysis predicts that the air conditioning capacity required to cool the cabin air in the silver car to 25?C within 30min is 13percent less than that required in the black car. Assuming that potential reductions in AC capacity and engine ancillary load scale linearly with increase in shell solar reflectance, ADVISOR simulations of the SC03 driving cycle indicate that substituting a typical cool-colored shell (?=0.35) for a black shell (?=0.05) would reduce fuel consumption by 0.12L per 100km (1.1percent), increasing fuel economy by 0.10kmL?1 [0.24mpg] (1.1percent). It would also decrease carbon dioxide (CO2) emissions by 2.7gkm?1 (1.1percent), nitrogen oxide (NOx) emissions by 5.4mgkm?1 (0.44percent), carbon monoxide (CO) emissions by 17mgkm?1 (0.43percent), and hydrocarbon (HC) emissions by 4.1mgkm?1 (0.37percent). Selecting a typical white or silver shell (?=0.60) instead of a black shell would lower fuel consumption by 0.21L per 100km (1.9percent), raising fuel economy by 0.19kmL?1 [0.44mpg] (2.0percent). It would also decrease CO2 emissions by 4.9gkm?1 (1.9percent), NOx emissions by 9.9mgkm?1 (0.80percent), CO emissions by 31mgkm?1 (0.79percent), and HC emissions by 7.4mgkm?1 (0.67percent). Our simulations may underestimate emission reductions because emissions in standardized driving

Black carbon emission reduction strategies in healthcare industry for effective global climate change management.

PubMed

Raila, Emilia Mmbando; Anderson, David O

2017-04-01

Climate change remains one of the biggest threats to life on earth to date with black carbon (BC) emissions or smoke being the strongest cause after carbon dioxide (CO 2 ). Surprisingly, scientific evidence about black carbon emissions reduction in healthcare settings is sparse. This paper presents new research findings on the reduction of black carbon emissions from an observational study conducted at the UN Peacekeeping Operations (MINUSTAH) in Haiti in 2014. Researchers observed 20 incineration cycles, 30 minutes for each cycle of plastic and cardboard sharps healthcare waste (HCW) containers ranged from 3 to 14.6 kg. The primary aim was to determine if black carbon emissions from healthcare waste incineration can be lowered by mainstreaming the use of cardboard sharps healthcare waste containers instead of plastic sharps healthcare waste containers. Similarly, the study looks into whether burning temperature was associated with the smoke levels for each case or not. Independent samples t-tests demonstrated significantly lower black carbon emissions during the incineration of cardboard sharps containers (6.81 ± 4.79% smoke) than in plastic containers (17.77 ± 8.38% smoke); a statistically significant increase of 10.96% smoke (95% Confidence Interval ( CI) [4.4 to 17.5% smoke], p = 0.003). Correspondingly, lower bottom burner temperatures occurred during the incineration of cardboard sharps containers than in plastic (95% Cl [16 to 126°C], p = 0.014). Finally, we expect the application of the new quantitative evidence to form the basis for policy formulation, mainstream the use of cardboard sharps containers and opt for non-incineration disposal technologies as urgent steps for going green in healthcare waste management.

Engine Validation of Noise and Emission Reduction Technology Phase I

NASA Technical Reports Server (NTRS)

Weir, Don (Editor)

2008-01-01

This final report has been prepared by Honeywell Aerospace, Phoenix, Arizona, a unit of Honeywell International, Inc., documenting work performed during the period December 2004 through August 2007 for the NASA Glenn Research Center, Cleveland, Ohio, under the Revolutionary Aero-Space Engine Research (RASER) Program, Contract No. NAS3-01136, Task Order 8, Engine Validation of Noise and Emission Reduction Technology Phase I. The NASA Task Manager was Dr. Joe Grady of the NASA Glenn Research Center. The NASA Contract Officer was Mr. Albert Spence of the NASA Glenn Research Center. This report is for a test program in which NASA funded engine validations of integrated technologies that reduce aircraft engine noise. These technologies address the reduction of engine fan and jet noise, and noise associated with propulsion/airframe integration. The results of these tests will be used by NASA to identify the engineering tradeoffs associated with the technologies that are needed to enable advanced engine systems to meet stringent goals for the reduction of noise. The objectives of this program are to (1) conduct system engineering and integration efforts to define the engine test-bed configuration; (2) develop selected noise reduction technologies to a technical maturity sufficient to enable engine testing and validation of those technologies in the FY06-07 time frame; (3) conduct engine tests designed to gain insight into the sources, mechanisms and characteristics of noise in the engines; and (4) establish baseline engine noise measurements for subsequent use in the evaluation of noise reduction.

Quantifying co-benefits of source-specific CO2 emission reductions in Canada and the US: An adjoint sensitivity analysis

NASA Astrophysics Data System (ADS)

Zhao, S.; Soltanzadeh, M.; Pappin, A. J.; Hakami, A.; Turner, M. D.; Capps, S.; Henze, D. K.; Percell, P.; Bash, J. O.; Napelenok, S. L.; Pinder, R. W.; Russell, A. G.; Nenes, A.; Baek, J.; Carmichael, G. R.; Stanier, C. O.; Chai, T.; Byun, D.; Fahey, K.; Resler, J.; Mashayekhi, R.

2016-12-01

Scenario-based studies evaluate air quality co-benefits by adopting collective measures introduced under a climate policy scenario cannot distinguish between benefits accrued from CO2 reductions among sources of different types and at different locations. Location and sector dependencies are important factors that can be captured in an adjoint-based analysis of CO2 reduction co-benefits. The present study aims to quantify how the ancillary benefits of reducing criteria co-pollutants vary spatially and by sector. The adjoint of USEPA's CMAQ was applied to quantify the health benefits associated with emission reduction of criteria pollutants (NOX) in on-road mobile, Electric Generation Units (EGUs), and other select sectors on a location-by-location basis across the US and Canada. These health benefits are then converted to CO2 emission reduction co-benefits by accounting for source-specific emission rates of criteria pollutants in comparison to CO2. We integrate the results from the adjoint of CMAQ with emission estimates from 2011 NEI at the county level, and point source data from EPA's Air Markets Program Data and National Pollutant Release Inventory (NPRI) for Canada. Our preliminary results show that the monetized health benefits (due to averted chronic mortality) associated with reductions of 1 ton of CO2 emissions is up to 65/ton in Canada and 200/ton in US for mobile on-road sector. For EGU sources, co-benefits are estimated at up to 100/ton and 10/ton for the US and Canada respectively. For Canada, the calculated co-benefits through gaseous pollutants including NOx is larger than those through PM2.5 due to the official association between NO2 exposure and chronic mortality. Calculated co-benefits show a great deal of spatial variability across emission locations for different sectors and sub-sectors. Implications of such spatial variability in devising control policy options that effectively address both climate and air quality objectives will be discussed.

Decreased N2O reduction by low soil pH causes high N2O emissions in a riparian ecosystem.

PubMed

Van den Heuvel, R N; Bakker, S E; Jetten, M S M; Hefting, M M

2011-05-01

Quantification of harmful nitrous oxide (N(2)O) emissions from soils is essential for mitigation measures. An important N(2)O producing and reducing process in soils is denitrification, which shows deceased rates at low pH. No clear relationship between N(2)O emissions and soil pH has yet been established because also the relative contribution of N(2)O as the denitrification end product decreases with pH. Our aim was to show the net effect of soil pH on N(2)O production and emission. Therefore, experiments were designed to investigate the effects of pH on NO(3)(-) reduction, N(2)O production and reduction and N(2) production in incubations with pH values set between 4 and 7. Furthermore, field measurements of soil pH and N(2)O emissions were carried out. In incubations, NO(3)(-) reduction and N(2) production rates increased with pH and net N(2)O production rate was highest at pH 5. N(2)O reduction to N(2) was halted until NO(3)(-) was depleted at low pH values, resulting in a built up of N(2)O. As a consequence, N(2)O:N(2) production ratio decreased exponentially with pH. N(2)O reduction appeared therefore more important than N(2)O production in explaining net N(2)O production rates. In the field, a negative exponential relationship for soil pH against N(2)O emissions was observed. Soil pH could therefore be used as a predictive tool for average N(2)O emissions in the studied ecosystem. The occurrence of low pH spots may explain N(2)O emission hotspot occurrence. Future studies should focus on the mechanism behind small scale soil pH variability and the effect of manipulating the pH of soils. © 2011 Blackwell Publishing Ltd.

Evaluation of carbon emission reductions promoted by private driving restrictions based on automatic fare collection data in Beijing, China.

PubMed

Zhang, Wandi; Chen, Feng; Wang, Zijia; Huang, Jianling; Wang, Bo

2017-11-01

Public transportation automatic fare collection (AFC) systems are able to continuously record large amounts of passenger travel information, providing massive, low-cost data for research on regulations pertaining to public transport. These data can be used not only to analyze characteristics of passengers' trips but also to evaluate transport policies that promote a travel mode shift and emission reduction. In this study, models combining card, survey, and geographic information systems (GIS) data are established with a research focus on the private driving restriction policies being implemented in an ever-increasing number of cities. The study aims to evaluate the impact of these policies on the travel mode shift, as well as relevant carbon emission reductions. The private driving restriction policy implemented in Beijing is taken as an example. The impact of the restriction policy on the travel mode shift from cars to subways is analyzed through a model based on metro AFC data. The routing paths of these passengers are also analyzed based on the GIS method and on survey data, while associated carbon emission reductions are estimated. The analysis method used in this study can provide reference for the application of big data in evaluating transport policies. Motor vehicles have become the most prevalent source of emissions and subsequently air pollution within Chinese cities. The evaluation of the effects of driving restriction policies on the travel mode shift and vehicle emissions will be useful for other cities in the future. Transport big data, playing an important support role in estimating the travel mode shift and emission reduction considered, can help related departments to estimate the effects of traffic jam alleviation and environment improvement before the implementation of these restriction policies and provide a reference for relevant decisions.

Emission reduction potential of using gas-to-liquid and dimethyl ether fuels on a turbocharged diesel engine.

PubMed

Xinling, Li; Zhen, Huang

2009-03-15

A study of engine performance characteristics and both of regulated (CO, HC, NO(x), and smoke) and unregulated (ultrafine particle number, mass concentrations and size distribution) emissions for a turbocharged diesel engine fueled with conventional diesel, gas-to-liquid (GTL) and dimethyl ether (DME) fuels respectively at different engine loads and speeds have been carried out. The results indicated that fuel components significantly affected the engine performance and regulated/unregulated emissions. GTL exhibited almost the same power and torque output as diesel, while improved fuel economy. GTL significantly reduced regulated emissions with average reductions of 21.2% in CO, 15.7% in HC, 15.6% in NO(x) and 22.1% in smoke in comparison to diesel, as well as average reductions in unregulated emissions of total ultrafine particle number (N(tot)) and mass (M(tot)) emissions by 85.3% and 43.9%. DME can significantly increase torque and power, compared with the original diesel engine, as well as significantly reduced regulated emissions of 40.1% in HC, 48.2% in NO(x) and smoke free throughout all the engine conditions. However, N(tot) for DME is close to that for diesel. The reason is that the accumulation mode particle number emissions for DME are very low due to the characteristics of oxygen content and no C-C bond, which promotes the processes of nucleation and condensation of the semi-volatile compounds in the exhaust gas, as a result, a lot of nucleation mode particles produce.

Direct observation of single layer graphene oxide reduction through spatially resolved, single sheet absorption/emission microscopy.

PubMed

Sokolov, Denis A; Morozov, Yurii V; McDonald, Matthew P; Vietmeyer, Felix; Hodak, Jose H; Kuno, Masaru

2014-06-11

Laser reduction of graphene oxide (GO) offers unique opportunities for the rapid, nonchemical production of graphene. By tuning relevant reduction parameters, the band gap and conductivity of reduced GO can be precisely controlled. In situ monitoring of single layer GO reduction is therefore essential. In this report, we show the direct observation of laser-induced, single layer GO reduction through correlated changes to its absorption and emission. Absorption/emission movies illustrate the initial stages of single layer GO reduction, its transition to reduced-GO (rGO) as well as its subsequent decomposition upon prolonged laser illumination. These studies reveal GO's photoreduction life cycle and through it native GO/rGO absorption coefficients, their intrasheet distributions as well as their spatial heterogeneities. Extracted absorption coefficients for unreduced GO are α405 nm ≈ 6.5 ± 1.1 × 10(4) cm(-1), α520 nm ≈ 2.1 ± 0.4 × 10(4) cm(-1), and α640 nm ≈ 1.1 ± 0.3 × 10(4) cm(-1) while corresponding rGO α-values are α405 nm ≈ 21.6 ± 0.6 × 10(4) cm(-1), α520 nm ≈ 16.9 ± 0.4 × 10(4) cm(-1), and α640 nm ≈ 14.5 ± 0.4 × 10(4) cm(-1). More importantly, the correlated absorption/emission imaging provides us with unprecedented insight into GO's underlying photoreduction mechanism, given our ability to spatially resolve its kinetics and to connect local rate constants to activation energies. On a broader level, the developed absorption imaging is general and can be applied toward investigating the optical properties of other two-dimensional materials, especially those that are nonemissive and are invisible to current single molecule optical techniques.

Fuel savings and emissions reductions from light duty fuel cell vehicles

NASA Astrophysics Data System (ADS)

Mark, J.; Ohi, J. M.; Hudson, D. V., Jr.

1994-04-01

Fuel cell vehicles (FCV's) operate efficiently, emit few pollutants, and run on nonpetroleum fuels. Because of these characteristics, the large-scale deployment of FCV's has the potential to lessen U.S. dependence on foreign oil and improve air quality. This study characterizes the benefits of large-scale FCV deployment in the light duty vehicle market. Specifically, the study assesses the potential fuel savings and emissions reductions resulting from large-scale use of these FCV's and identifies the key parameters that affect the scope of the benefits from FCV use. The analysis scenario assumes that FCV's will compete with gasoline-powered light trucks and cars in the new vehicle market for replacement of retired vehicles and will compete for growth in the total market. Analysts concluded that the potential benefits from FCV's, measured in terms of consumer outlays for motor fuel and the value of reduced air emissions, are substantial.

Reduction in greenhouse gas emissions from sludge biodrying instead of heat drying combined with mono-incineration in China.

PubMed

Liu, Hong-Tao; Wang, Yan-Wen; Liu, Xiao-Jie; Gao, Ding; Zheng, Guo-di; Lei, Mei; Guo, Guang-Hui; Zheng, Hai-Xia; Kong, Xiang-Juan

2017-02-01

Sludge is an important source of greenhouse gas (GHG) emissions, both in the form of direct process emissions and as a result of indirect carbon-derived energy consumption during processing. In this study, the carbon budgets of two sludge disposal processes at two well-known sludge disposal sites in China (for biodrying and heat-drying pretreatments, both followed by mono-incineration) were quantified and compared. Total GHG emissions from heat drying combined with mono-incineration was 0.1731 tCO 2 e t -1 , while 0.0882 tCO 2 e t -1 was emitted from biodrying combined with mono-incineration. Based on these findings, a significant reduction (approximately 50%) in total GHG emissions was obtained by biodrying instead of heat drying prior to sludge incineration. Sludge treatment results in direct and indirect greenhouse gas (GHG) emissions. Moisture reduction followed by incineration is commonly used to dispose of sludge in China; however, few studies have compared the effects of different drying pretreatment options on GHG emissions during such processes. Therefore, in this study, the carbon budgets of sludge incineration were analyzed and compared following different pretreatment drying technologies (biodrying and heat drying). The results indicate that biodrying combined with incineration generated approximately half of the GHG emissions compared to heat drying followed by incineration. Accordingly, biodrying may represent a more environment-friendly sludge pretreatment prior to incineration.

The effectiveness of policy on consumer choices for private road passenger transport emissions reductions in six major economies

NASA Astrophysics Data System (ADS)

Mercure, J.-F.; Lam, A.

2015-06-01

The effectiveness of fiscal policy to influence vehicle purchases for emissions reductions in private passenger road transport depends on its ability to incentivise consumers to make choices oriented towards lower emissions vehicles. However, car purchase choices are known to be strongly socially determined, and this sector is highly diverse due to significant socio-economic differences between consumer groups. Here, we present a comprehensive dataset and analysis of the structure of the 2012 private passenger vehicle fleet-years in six major economies across the World (UK, USA, China, India, Japan and Brazil) in terms of price, engine size and emissions distributions. We argue that choices and aggregate elasticities of substitution can be predicted using this data, enabling us to evaluate the effectiveness of potential fiscal and technological change policies on fleet-year emissions reductions. We provide tools to do so based on the distributive structure of prices and emissions in segments of a diverse market, both for conventional as well as unconventional engine technologies. We find that markets differ significantly between nations, and that correlations between engine sizes, emissions and prices exist strongly in some markets and not strongly in others. We furthermore find that markets for unconventional engine technologies have patchy coverages of varying levels. These findings are interpreted in terms of policy strategy.

Effects of idle reduction technologies on real world fuel use and exhaust emissions of idling long-haul trucks.

PubMed

Frey, H Christopher; Kuo, Po-Yao; Villa, Charles

2009-09-01

Idling long-haul freight tucks may consume nearly one billion gallons of diesel fuel per year in the U.S. There is a need for real-world data by which to quantify avoided fuel use and emissions attributable to idle reduction techniques of auxiliary power units (APUs) and shore-power (SP). Field data were obtained from 20 APU-equipped and SP-compatible trucks observed during 2.8 million miles of travel in 42 states. Base engine fuel use and emission rates varied depending on ambient temperature. APU and SP energy use and emission rates varied depending on electrical load. APUs reduced idling fuel use and CO2 emissions for single and team drivers by 22 and 5% annually, respectively. SP offers greater reductions in energy use of 48% for single drivers, as well as in emissions, except for SO2. APUs were cost-effective for single drivers with a large number of APU usage hours per year, but not for team drivers or for single drivers with low APU utilization rates. The findings support more accurate assessments of avoided fuel use and emissions, and recommendations to encourage greater APU utilization by single drivers and to further develop infrastructure for SP.

Identifying potential exposure reduction priorities using regional rankings based on emissions of known and suspected carcinogens to outdoor air in Canada.

PubMed

Setton, Eleanor M; Veerman, Basil; Erickson, Anders; Deschenes, Steeve; Cheasley, Roz; Poplawski, Karla; Demers, Paul A; Keller, C Peter

2015-08-22

Emissions inventories aid in understanding the sources of hazardous air pollutants and how these vary regionally, supporting targeted reduction actions. Integrating information on the relative toxicity of emitted pollutants with respect to cancer in humans helps to further refine reduction actions or recommendations, but few national programs exist in North America that use emissions estimates in this way. The CAREX Canada Emissions Mapping Project provides key regional indicators of emissions (total annual and total annual toxic equivalent, circa 2011) of 21 selected known and suspected carcinogens. The indicators were calculated from industrial emissions reported to the National Pollutant Release Inventory (NPRI) and estimates of emissions from transportation (airports, trains, and car and truck traffic) and residential heating (oil, gas and wood), in conjunction with human toxicity potential factors. We also include substance-specific annual emissions in toxic equivalent kilograms and annual emissions in kilograms, to allow for ranking substances within any region. For provinces and territories in Canada, the indicators suggest the top five substances contributing to the total toxic equivalent emissions in any region could be prioritized for further investigation. Residents of Quebec and New Brunswick may be more at risk of exposure to industrial emissions than those in other regions, suggesting that a more detailed study of exposure to industrial emissions in these provinces is warranted. Residential wood smoke may be an important emission to control, particularly in the north and eastern regions of Canada. Residential oil and gas heating, along with rail emissions contribute little to regional emissions and therefore may not be an immediate regional priority. The developed indicators support the identification of pollutants and sources for additional investigation when planning exposure reduction actions among Canadian provinces and territories, but have

INTRODUCTION OF UNIVERSAL HEALTH PROGRAM IN GEORGIA: PROBLEMS AND PERSPECTIVES.

PubMed

Verulava, T; Jorbenadze, R; Barkalaia, T

2017-01-01

Since 2013, Georgia enacted Universal Healthcare (UHC) program. Inclusion of uninsured population in the UHC program will have a positive impact on their financial accessibility to the health services. The study aims to analyze the referral rate of the beneficiaries to the health service providers before introduction and after application of the UHC program, particularly, how much it increased the recently uninsured population referral to primary health care units, and also to study the level of satisfaction with the UHC program. Research was conducted by qualitative and quantitative methods. The target groups' (program beneficiaries, physicians, personnel of the Social Service Agency) opinions were identified by means of face-to-face interviews. Enactment of the UHC programs significantly raised the population refferal to the family physicians, and the specialists. Insignificantly, but also increased the frequency of laboratory and diagnostic services. Despite the serious positive changes caused by UHC program implementation there still remain the problems in the primary healthcare system. Also, it is desirable to raise the financial availability of those medical services, which may cause catastrophic costs. In this respect, such medical services must be involved in the universal healthcare program and been expanded their scale. For the purpose of effective usage of the limited funds allocated for health care services provision, the private health insurance companies should be involved in UHC programs. This, together with the reduction of health care costs will increase a competition in the medical market, and enhance the quality of health service.

INVESTIGATION OF SELECTIVE CATALYTIC REDUCTION IMPACT ON MERCURY SPECIATION UNDER SIMULATED NOX EMISSION CONTROL CONDITIONS

EPA Science Inventory

Selective catalytic reduction (SCR) technology is being increasingly applied for controlling emissions of nitrogen oxides (NOx) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury in the coal com...

Reduction of emission level in approach signals of greater mouse-eared bats (Myotis myotis): No evidence for a closed loop control system for intensity compensation.

PubMed

Budenz, Tobias; Denzinger, Annette; Schnitzler, Hans-Ulrich

2018-01-01

Bats lower the emission SPL when approaching a target. The SPL reduction has been explained by intensity compensation which implies that bats adjust the emission SPL to perceive the retuning echoes at the same level. For a better understanding of this control mechanism we recorded the echolocation signals of four Myotis myotis with an onboard microphone when foraging in the passive mode for rustling mealworms offered in two feeding dishes with different target strength, and determined the reduction rate for the emission SPL and the increase rate for the SPL of the returning echoes. When approaching the dish with higher target strength bats started the reduction of the emission SPL at a larger reaction distance (1.05 ± 0.21 m) and approached it with a lower reduction rate of 7.2 dB/halving of distance (hd), thus producing a change of echo rate at the ears of + 4 dB/hd. At the weaker target reaction distance was shorter (0.71 ± 0.24 m) and the reduction rate (9.1 dB/hd) was higher, producing a change of echo rate of-1.2 dB/hd. Independent of dish type, bats lowered the emission SPL by about 26 dB on average. In one bat where the echo SPL from both targets could be measured, the reduction of emission SPL was triggered when the echo SPL surpassed a similar threshold value around 41-42 dB. Echo SPL was not adjusted at a constant value indicating that Myotis myotis and most likely all other bats do not use a closed loop system for intensity compensation when approaching a target of interest. We propose that bats lower the emission SPL to adjust the SPL of the perceived pulse-echo-pairs to the optimal auditory range for the processing of range information and hypothesize that bats use flow field information not only to control the reduction of the approach speed to the target but also to control the reduction of emission SPL.

Creating rigorous pathways to monetize methane and nitrous oxide emission reductions at small scale rice farms in three states of semi-arid peninsular India

NASA Astrophysics Data System (ADS)

Kritee, K.; Tiwari, R.; Nair, D.; Adhya, T. K.; Rudek, J.

2014-12-01

As a part of a joint undertaking by Environmental Defense Fund and the Fair Climate Network, we have measured reduction in methane and nitrous oxide emissions due to alternate "low carbon" rice cultivation practices for three ago-ecological zones in India for the past two years. Sampling for nitrous oxide and methane emissions was done on approximately 60-80% of the total number of days in a growing season and was based on modified GRACEnet protocol. In recognition of farmer's economic interest and global food security demands, we also measured the effect of rice cultivation practices on farm economics and yields. Our data from three agro-ecological zones for 2012-2014 suggest that, for semi-arid peninsular India, low-carbon rice cultivation practices offer large range of emission reduction potential (0.5-5 metric tons CO2e/acre/year). The regions with sandy soils (Alfisols) had high rates of nitrous oxide emissions even under baseline "flooded" rice cultivation regimes and, thus, the Tier 1 IPCC emissions factors grossly underestimate both the amount of nitrous oxide emission from conventional rice cultivation practices, and the extent to which it can be reduced through better fertilizer management. Also, the IPCC factors overestimate the methane emission reduction possible due to water management for rice paddies. Therefore, it is crucial to customize N and water management to each region such that yields and net GHG emission reduction are maximized. These practices also have the potential to decrease water use by 10-30% and improve long term soil health by optimizing organic matter and increasing water-holding capacity. In addition, through GPS based demarcation of farmer plots, recording baseline practices through extensive surveys, documenting the parameters required to aggregate and prove implementation of low carbon rice farming practices, and to model the GHG emission reduction over large scales, we have put forward a path for better monetization of GHG

Assessment of PM10 pollution level and required source emission reduction in Belgrade area.

PubMed

Todorović, Marija N; Perišić, Mirjana D; Kuzmanoski, Maja M; Stojić, Andreja M; Sostarić, Andrej I; Mijić, Zoran R; Rajšić, Slavica F

2015-01-01

The aim of this study was to assess PM10 pollution level and estimate required source emission reduction in Belgrade area, the second largest urban center in the Balkans. Daily mass concentrations and trace metal content (As, Cd, Cr, Mn, Ni, Pb) of PM10 were evaluated for three air quality monitoring sites of different types: urban-traffic (Slavija), suburban (Lazarevac) and rural (Grabovac) under the industrial influence, during the period of 2012-13. Noncompliance with current Air Quality Standards (AQS) was noticeable: annual means were higher than AQS at Slavija and Lazarevac, and daily frequency threshold was exceeded at all three locations. Annual means of As at Lazarevac were about four times higher than the target concentration, which could be attributed to the proximity of coal-fired power plants, and dust resuspension from coal basin and nearby ash landfills. Additionally, levels of Ni and Cr were significantly higher than in other European cities. Carcinogenic health risk of inhabitants' exposure to trace metals was assessed as well. Cumulative cancer risk exceeded the upper limit of acceptable US EPA range at two sites, with Cr and As as the major contributors. To estimate source emission reduction, required to meet AQS, lognormal, Weibull and Pearson 5 probability distribution, functions (PDF) were used to fit daily PM10 concentrations. Based on the rollback equation and best fitting PDF, estimated reduction was within the range of 28-98%. Finally, the required reduction obtained using two-parameter exponential distribution suggested that risks associated to accidental releases of pollutants should be of greater concern.

[Synergistic emission reduction of chief air pollutants and greenhouse gases-based on scenario simulations of energy consumptions in Beijing].

PubMed

Xie, Yuan-bo; Li, Wei

2013-05-01

It is one of the common targets and important tasks for energy management and environmental control of Beijing to improve urban air quality while reducing the emissions of greenhouse gases (GHG). Here, based on the interim and long term developmental planning and energy structure of the city, three energy consumption scenarios in low, moderate and high restrictions were designed by taking the potential energy saving policies and environmental targets into account. The long-range energy alternatives planning (LEAP) model was employed to predict and evaluate reduction effects of the chief air pollutants and GHG during 2010 to 2020 under the three given scenarios. The results showed that if urban energy consumption system was optimized or adjusted by exercising energy saving and emission reduction and pollution control measures, the predicted energy uses will be reduced by 10 to 30 million tons of coal equivalents by 2020. Under the two energy scenarios with moderate and high restrictions, the anticipated emissions of SO2, NOx, PM10, PM2.5, VOC and GHG will be respectively reduced to 71 to 100.2, 159.2 to 218.7, 89.8 to 133.8, 51.4 to 96.0, 56.4 to 74.8 and 148 200 to 164 700 thousand tons. Correspondingly, when compared with the low-restriction scenario, the reducing rate will be 53% to 67% , 50% to 64% , 33% to 55% , 25% to 60% , 41% to 55% and 26% to 34% respectively. Furthermore, based on a study of synergistic emission reduction of the air pollutants and GHG, it was proposed that the adjustment and control of energy consumptions shall be intensively developed in the three sectors of industry, transportation and services. In this way the synergistic reduction of the emissions of chief air pollutants and GHG will be achieved; meanwhile the pressures of energy demands may be deliberately relieved.

Cement replacement by sugar cane bagasse ash: CO2 emissions reduction and potential for carbon credits.

PubMed

Fairbairn, Eduardo M R; Americano, Branca B; Cordeiro, Guilherme C; Paula, Thiago P; Toledo Filho, Romildo D; Silvoso, Marcos M

2010-09-01

This paper presents a study of cement replacement by sugar cane bagasse ash (SCBA) in industrial scale aiming to reduce the CO(2) emissions into the atmosphere. SCBA is a by-product of the sugar/ethanol agro-industry abundantly available in some regions of the world and has cementitious properties indicating that it can be used together with cement. Recent comprehensive research developed at the Federal University of Rio de Janeiro/Brazil has demonstrated that SCBA maintains, or even improves, the mechanical and durability properties of cement-based materials such as mortars and concretes. Brazil is the world's largest sugar cane producer and being a developing country can claim carbon credits. A simulation was carried out to estimate the potential of CO(2) emission reductions and the viability to issue certified emission reduction (CER) credits. The simulation was developed within the framework of the methodology established by the United Nations Framework Convention on Climate Change (UNFCCC) for the Clean Development Mechanism (CDM). The State of São Paulo (Brazil) was chosen for this case study because it concentrates about 60% of the national sugar cane and ash production together with an important concentration of cement factories. Since one of the key variables to estimate the CO(2) emissions is the average distance between sugar cane/ethanol factories and the cement plants, a genetic algorithm was developed to solve this optimization problem. The results indicated that SCBA blended cement reduces CO(2) emissions, which qualifies this product for CDM projects. 2010 Elsevier Ltd. All rights reserved.

Meat consumption reduction in Italian regions: Health co-benefits and decreases in GHG emissions.

PubMed

Farchi, Sara; De Sario, Manuela; Lapucci, Enrica; Davoli, Marina; Michelozzi, Paola

2017-01-01

Animal agriculture has exponentially grown in recent decades in response to the rise in global demand for meat, even in countries like Italy that traditionally eat a Mediterranean, plant-based diet. Globalization related dietary changes are contributing to the epidemic of non-communicable diseases and to the global climate crisis, and are associated with huge carbon and water footprints. The objective of the study is to assess inequalities in health impacts and in attributable greenhouse gases-GHG emissions in Italy by hypothesizing different scenarios of reduction in red and processed meat consumption towards healthier consumption patterns more compliant with the recommendations of the Mediterranean food pyramid. We used demographic and food consumption patterns from national surveys and risk relationships between meat intake and cardiovascular and colorectal cancer mortality from IARC and other meta-analyses. From the baseline data (year 2005-2006, average 406 gr/week beef and 245 gr/week processed meat), we considered hypothetical meat reduction scenarios according to international dietary guidelines such as the Mediterranean pyramid targets. For each geographical area (Northwest, Northeast, Centre, and South) and gender, we calculated the number of avoidable deaths from colorectal cancer, and cardiovascular disease among the adult population. Moreover, years of life gained by the adult population from 2012 to 2030 and changes in life expectancy of the 2012 birth cohort were quantified using gender-specific life tables. GHG emission reductions under Mediterranean scenario were estimated only for beef by applying the Global Warming Potential (GWP) coefficient to total consumption and to a low carbon food substitution in adult diet. The deaths avoidable (as percentage change compared to baseline) according to the three reduction scenarios for beef consumption were between 2.3% and 4.5% for colorectal cancer, and between 2.1% and 4.0% for cardiovascular disease

Meat consumption reduction in Italian regions: Health co-benefits and decreases in GHG emissions

PubMed Central

Farchi, Sara; De Sario, Manuela; Lapucci, Enrica; Davoli, Marina; Michelozzi, Paola

2017-01-01

Introduction Animal agriculture has exponentially grown in recent decades in response to the rise in global demand for meat, even in countries like Italy that traditionally eat a Mediterranean, plant-based diet. Globalization related dietary changes are contributing to the epidemic of non-communicable diseases and to the global climate crisis, and are associated with huge carbon and water footprints. The objective of the study is to assess inequalities in health impacts and in attributable greenhouse gases-GHG emissions in Italy by hypothesizing different scenarios of reduction in red and processed meat consumption towards healthier consumption patterns more compliant with the recommendations of the Mediterranean food pyramid. Methods We used demographic and food consumption patterns from national surveys and risk relationships between meat intake and cardiovascular and colorectal cancer mortality from IARC and other meta-analyses. From the baseline data (year 2005–2006, average 406 gr/week beef and 245 gr/week processed meat), we considered hypothetical meat reduction scenarios according to international dietary guidelines such as the Mediterranean pyramid targets. For each geographical area (Northwest, Northeast, Centre, and South) and gender, we calculated the number of avoidable deaths from colorectal cancer, and cardiovascular disease among the adult population. Moreover, years of life gained by the adult population from 2012 to 2030 and changes in life expectancy of the 2012 birth cohort were quantified using gender-specific life tables. GHG emission reductions under Mediterranean scenario were estimated only for beef by applying the Global Warming Potential (GWP) coefficient to total consumption and to a low carbon food substitution in adult diet. Results The deaths avoidable (as percentage change compared to baseline) according to the three reduction scenarios for beef consumption were between 2.3% and 4.5% for colorectal cancer, and between 2.1% and 4

On the possibilities of reduction in emission caused by home tile stoves in Cracow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szewczyk, W.

1995-12-31

The coal-fired tile stoves are still very popular in Poland. The estimated total number of such home stoves operated in Cracow reaches ca. 100 000. Operation of these stoves during the heating season belongs to the most significant sources of air pollution. Type and scale of emission of the most important pollutants, caused by coal combustion in home stoves in Cracow has been determined basing upon the investigations carried out at the laboratory of the Department of Power Engineering Machines and Devices, Academy of Mining and Metallurgy, Cracow, Poland within the American-Polish Program of Elimination of Low Emission Sources inmore » Cracow. Further experiments included in this Program allowed to estimate the attainable efficiency of home tile stoves and possible reduction in pollutant emission resulting from their operation. A short discussion of these data and capacities is presented in this lecture.« less

Modelling road dust emission abatement measures using the NORTRIP model: Vehicle speed and studded tyre reduction

NASA Astrophysics Data System (ADS)

Norman, M.; Sundvor, I.; Denby, B. R.; Johansson, C.; Gustafsson, M.; Blomqvist, G.; Janhäll, S.

2016-06-01

Road dust emissions in Nordic countries still remain a significant contributor to PM10 concentrations mainly due to the use of studded tyres. A number of measures have been introduced in these countries in order to reduce road dust emissions. These include speed reductions, reductions in studded tyre use, dust binding and road cleaning. Implementation of such measures can be costly and some confidence in the impact of the measures is required to weigh the costs against the benefits. Modelling tools are thus required that can predict the impact of these measures. In this paper the NORTRIP road dust emission model is used to simulate real world abatement measures that have been carried out in Oslo and Stockholm. In Oslo both vehicle speed and studded tyre share reductions occurred over a period from 2004 to 2006 on a major arterial road, RV4. In Stockholm a studded tyre ban on Hornsgatan in 2010 saw a significant reduction in studded tyre share together with a reduction in traffic volume. The model is found to correctly simulate the impact of these measures on the PM10 concentrations when compared to available kerbside measurement data. Importantly meteorology can have a significant impact on the concentrations through both surface and dispersion conditions. The first year after the implementation of the speed reduction on RV4 was much drier than the previous year, resulting in higher mean concentrations than expected. The following year was much wetter with significant rain and snow fall leading to wet or frozen road surfaces for 83% of the four month study period. This significantly reduced the net PM10 concentrations, by 58%, compared to the expected values if meteorological conditions had been similar to the previous years. In the years following the studded tyre ban on Hornsgatan road wear production through studded tyres decreased by 72%, due to a combination of reduced traffic volume and reduced studded tyre share. However, after accounting for exhaust

10 CFR 300.7 - Net emission reductions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.7... practicable, on a full assessment and sum total of all changes in an entity's emissions, eligible avoided... include the annual changes in the total emissions of the entity, including the total emissions of each of...

10 CFR 300.7 - Net emission reductions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.7... practicable, on a full assessment and sum total of all changes in an entity's emissions, eligible avoided... include the annual changes in the total emissions of the entity, including the total emissions of each of...

10 CFR 300.7 - Net emission reductions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.7... practicable, on a full assessment and sum total of all changes in an entity's emissions, eligible avoided... include the annual changes in the total emissions of the entity, including the total emissions of each of...

10 CFR 300.7 - Net emission reductions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.7... practicable, on a full assessment and sum total of all changes in an entity's emissions, eligible avoided... include the annual changes in the total emissions of the entity, including the total emissions of each of...

10 CFR 300.7 - Net emission reductions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... DEPARTMENT OF ENERGY CLIMATE CHANGE VOLUNTARY GREENHOUSE GAS REPORTING PROGRAM: GENERAL GUIDELINES § 300.7... practicable, on a full assessment and sum total of all changes in an entity's emissions, eligible avoided... include the annual changes in the total emissions of the entity, including the total emissions of each of...

Breakdown voltage reduction by field emission in multi-walled carbon nanotubes based ionization gas sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saheed, M. Shuaib M.; Muti Mohamed, Norani; Arif Burhanudin, Zainal, E-mail: zainabh@petronas.com.my

2014-03-24

Ionization gas sensors using vertically aligned multi-wall carbon nanotubes (MWCNT) are demonstrated. The sharp tips of the nanotubes generate large non-uniform electric fields at relatively low applied voltage. The enhancement of the electric field results in field emission of electrons that dominates the breakdown mechanism in gas sensor with gap spacing below 14 μm. More than 90% reduction in breakdown voltage is observed for sensors with MWCNT and 7 μm gap spacing. Transition of breakdown mechanism, dominated by avalanche electrons to field emission electrons, as decreasing gap spacing is also observed and discussed.

The impact of local government investment on the carbon emissions reduction effect: An empirical analysis of panel data from 30 provinces and municipalities in China.

PubMed

He, Lingyun; Yin, Fang; Zhong, Zhangqi; Ding, Zhihua

2017-01-01

Among studies of the factors that influence carbon emissions and related regulations, economic aggregates, industrial structures, energy structures, population levels, and energy prices have been extensively explored, whereas studies from the perspective of fiscal leverage, particularly of local government investment (LGI), are rare. Of the limited number of studies on the effect of LGI on carbon emissions, most focus on its direct effect. Few studies consider regulatory effects, and there is a lack of emphasis on local areas. Using a cointegration test, a panel data model and clustering analysis based on Chinese data between 2000 and 2013, this study measures the direct role of LGI in carbon dioxide (CO2) emissions reduction. First, overall, within the sample time period, a 1% increase in LGI inhibits carbon emissions by 0.8906% and 0.5851% through its influence on the industrial structure and energy efficiency, respectively, with the industrial structure path playing a greater role than the efficiency path. Second, carbon emissions to some extent exhibit inertia. The previous year's carbon emissions impact the following year's carbon emissions by 0.5375%. Thus, if a reduction in carbon emissions in the previous year has a positive effect, then the carbon emissions reduction effect generated by LGI in the following year will be magnified. Third, LGI can effectively reduce carbon emissions, but there are significant regional differences in its impact. For example, in some provinces, such as Sichuan and Anhui, economic growth has not been decoupled from carbon emissions. Fourth, the carbon emissions reduction effect in the 30 provinces and municipalities sampled in this study can be classified into five categories-strong, relatively strong, medium, relatively weak and weak-based on the degree of local governments' regulation of carbon emissions. The carbon emissions reduction effect of LGI is significant in the western and central regions of China but not in the

The impact of local government investment on the carbon emissions reduction effect: An empirical analysis of panel data from 30 provinces and municipalities in China

PubMed Central

He, Lingyun; Yin, Fang; Zhong, Zhangqi; Ding, Zhihua

2017-01-01

Among studies of the factors that influence carbon emissions and related regulations, economic aggregates, industrial structures, energy structures, population levels, and energy prices have been extensively explored, whereas studies from the perspective of fiscal leverage, particularly of local government investment (LGI), are rare. Of the limited number of studies on the effect of LGI on carbon emissions, most focus on its direct effect. Few studies consider regulatory effects, and there is a lack of emphasis on local areas. Using a cointegration test, a panel data model and clustering analysis based on Chinese data between 2000 and 2013, this study measures the direct role of LGI in carbon dioxide (CO2) emissions reduction. First, overall, within the sample time period, a 1% increase in LGI inhibits carbon emissions by 0.8906% and 0.5851% through its influence on the industrial structure and energy efficiency, respectively, with the industrial structure path playing a greater role than the efficiency path. Second, carbon emissions to some extent exhibit inertia. The previous year’s carbon emissions impact the following year’s carbon emissions by 0.5375%. Thus, if a reduction in carbon emissions in the previous year has a positive effect, then the carbon emissions reduction effect generated by LGI in the following year will be magnified. Third, LGI can effectively reduce carbon emissions, but there are significant regional differences in its impact. For example, in some provinces, such as Sichuan and Anhui, economic growth has not been decoupled from carbon emissions. Fourth, the carbon emissions reduction effect in the 30 provinces and municipalities sampled in this study can be classified into five categories—strong, relatively strong, medium, relatively weak and weak—based on the degree of local governments’ regulation of carbon emissions. The carbon emissions reduction effect of LGI is significant in the western and central regions of China but not

Costs and benefits of an enhanced reduction policy of particulate matter exhaust emissions from road traffic in Flanders

NASA Astrophysics Data System (ADS)

Schrooten, Liesbeth; De Vlieger, Ina; Lefebre, Filip; Torfs, Rudi

We demonstrate that accelerated policies beyond the steady improvement of technologies and the fleet turnover are not always justified by assumptions about health benefits. Between the years 2000 and 2010, particulate matter (PM) exhaust emissions from traffic in Flanders, a region of Belgium, will be reduced by about 44% without taking any extra reduction measures (baseline scenario). The PM emissions from road traffic were calculated using the MIMOSA model. Furthermore, we explored a range of options to increase attempts to reduce PM exhaust emission from traffic in 2010. When installing particle filters on heavy-duty trucks and buses, introducing biodiesel and diesel/hybrid cars, as well as slowing down the increase of private diesel cars, only an extra reduction of about 8% PM can be achieved in Flanders. The costs to achieve this small reduction are very high. To justify these costs, benefits for public health have been calculated and expressed in external costs. We demonstrate that only an enhanced effort to retrofit trucks and buses with particle filters has a net benefit. We have used Monte Carlo techniques to test the validity of this conclusion. It is concluded that a local or national policy that goes beyond European policies is not always beneficial and that additional measures should be assessed carefully.

Reduction of ruminant methane emissions - a win-win-win opportunity for business, development, and the environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Livingston, R.

1997-12-31

This paper describes research efforts of The Global Livestock Producers Program (GLPP) in establishing self-sustaining enterprises for cost-effective technologies (i.e., animal nutrition and genetic improvement) and global methane emissions reductions in developing world nations. The US Environmental Protection Agency has funded several studies to examine the possibilities of reducing ruminant methane emissions in India, Tanzania, Bangladesh, and Brazil. The results of the studies showed that: (1) many developing countries` production systems are inefficient, and (2) great potential exists for decreasing global methane emissions through increasing animal productivity. From this effort, the GLPP established livestock development projects in India, Zimbabwe, andmore » Tanzania, and is developing projects for Bangladesh, Nepal, and Brazil. The GLPP has developed a proven methodology for assessing ruminant methane and incorporating methane emissions monitoring into viable projects.« less

Integrated control of emission reductions, energy-saving, and cost-benefit using a multi-objective optimization technique in the pulp and paper industry.

PubMed

Wen, Zongguo; Xu, Chang; Zhang, Xueying

2015-03-17

Reduction of water pollutant emissions and energy consumption is regarded as a key environmental objective for the pulp and paper industry. The paper develops a bottom-up model called the Industrial Water Pollutant Control and Technology Policy (IWPCTP) based on an industrial technology simulation system and multiconstraint technological optimization. Five policy scenarios covering the business as usual (BAU) scenario, the structural adjustment (SA) scenario, the cleaner technology promotion (CT) scenario, the end-treatment of pollutants (EOP) scenario, and the coupling measures (CM) scenario have been set to describe future policy measures related to the development of the pulp and paper industry from 2010-2020. The outcome of this study indicates that the energy saving amount under the CT scenario is the largest, while that under the SA scenario is the smallest. Under the CT scenario, savings by 2020 include 70 kt/year of chemical oxygen demand (COD) emission reductions and savings of 7443 kt of standard coal, 539.7 ton/year of ammonia nitrogen (NH4-N) emission reductions, and savings of 7444 kt of standard coal. Taking emission reductions, energy savings, and cost-benefit into consideration, cleaner technologies like highly efficient pulp washing, dry and wet feedstock preparation, and horizontal continuous cooking, medium and high consistency pulping and wood dry feedstock preparation are recommended.

High emission reduction performance of a novel organic-inorganic composite filters containing sepiolite mineral nanofibers

PubMed Central

Wang, Fei; Zhang, Hui; Liang, Jinsheng; Tang, Qingguo; Li, Yanxia; Shang, Zengyao

2017-01-01

In this work, a new organic-inorganic composite filter was prepared. The thickness, pore size, air permeability, bursting strength and microstructure were characterized systematically, proving that coatings had regulatory effect on filters physical properties. Benefitting from the distinct coatings containing 5% sepiolite nanofibers after five times dilution, the physical properties of corresponding air filter exhibits the most favorable performance and meet the standard of air filter. When used as fuel filter, it satisfies the fuel filter standard and achieves the best performance after six times dilution. The contrast test on engine emission was taken based on auto filters coated with/without as prepared nanofibers. An obvious decrease in the emission of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NOx) can be observed after installation of composite filter on vehicles. Under the high idle condition, gasoline engine emission decreased by 8.13%, 11.35% and 44.91% for CO, HC and NOx, respectively. When tested in the low idle condition, engine emission reduced by 0.43%, 1.14% and 85.67% for CO, HC and NOx, respectively. The diesel engine emissions of CO, NOx and total amount of HC and NOx decreased by 32.26%, 3.28% and 4.66%, respectively. The results illustrate the composite installation exhibits satisfactory emission reduction effect. PMID:28252034

High emission reduction performance of a novel organic-inorganic composite filters containing sepiolite mineral nanofibers

NASA Astrophysics Data System (ADS)

Wang, Fei; Zhang, Hui; Liang, Jinsheng; Tang, Qingguo; Li, Yanxia; Shang, Zengyao

2017-03-01

In this work, a new organic-inorganic composite filter was prepared. The thickness, pore size, air permeability, bursting strength and microstructure were characterized systematically, proving that coatings had regulatory effect on filters physical properties. Benefitting from the distinct coatings containing 5% sepiolite nanofibers after five times dilution, the physical properties of corresponding air filter exhibits the most favorable performance and meet the standard of air filter. When used as fuel filter, it satisfies the fuel filter standard and achieves the best performance after six times dilution. The contrast test on engine emission was taken based on auto filters coated with/without as prepared nanofibers. An obvious decrease in the emission of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NOx) can be observed after installation of composite filter on vehicles. Under the high idle condition, gasoline engine emission decreased by 8.13%, 11.35% and 44.91% for CO, HC and NOx, respectively. When tested in the low idle condition, engine emission reduced by 0.43%, 1.14% and 85.67% for CO, HC and NOx, respectively. The diesel engine emissions of CO, NOx and total amount of HC and NOx decreased by 32.26%, 3.28% and 4.66%, respectively. The results illustrate the composite installation exhibits satisfactory emission reduction effect.

Ratcheting ambition to limit warming to 1.5 °C–trade-offs between emission reductions and carbon dioxide removal

NASA Astrophysics Data System (ADS)

Holz, Christian; Siegel, Lori S.; Johnston, Eleanor; Jones, Andrew P.; Sterman, John

2018-06-01

Mitigation scenarios to limit global warming to 1.5 °C or less in 2100 often rely on large amounts of carbon dioxide removal (CDR), which carry significant potential social, environmental, political and economic risks. A precautionary approach to scenario creation is therefore indicated. This letter presents the results of such a precautionary modelling exercise in which the models C-ROADS and En-ROADS were used to generate a series of 1.5 °C mitigation scenarios that apply increasingly stringent constraints on the scale and type of CDR available. This allows us to explore the trade-offs between near-term stringency of emission reductions and assumptions about future availability of CDR. In particular, we find that regardless of CDR assumptions, near-term ambition increase (‘ratcheting’) is required for any 1.5 °C pathway, making this letter timely for the facilitative, or Talanoa, dialogue to be conducted by the UNFCCC in 2018. By highlighting the difference between net and gross reduction rates, often obscured in scenarios, we find that mid-term gross CO2 emission reduction rates in scenarios with CDR constraints increase to levels without historical precedence. This in turn highlights, in addition to the need to substantially increase CO2 reduction rates, the need to improve emission reductions for non-CO2 greenhouse gases. Further, scenarios in which all or part of the CDR is implemented as non-permanent storage exhibit storage loss emissions, which partly offset CDR, highlighting the importance of differentiating between net and gross CDR in scenarios. We find in some scenarios storage loss trending to similar values as gross CDR, indicating that gross CDR would have to be maintained simply to offset the storage losses of CO2 sequestered earlier, without any additional net climate benefit.

Assessment of Energy Efficiency Improvement and CO2 Emission Reduction Potentials in India's Cement Industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morrow, III, William R.; Hasanbeigi, Ali; Xu, Tengfang

2012-12-03

India’s cement industry is the second largest in the world behind China with annual cement production of 168 Mt in 2010 which accounted for slightly greater than six percent of the world’s annual cement production in the same year. To produce that amount of cement, the industry consumed roughly 700 PJ of fuel and 14.7 TWh of electricity. We identified and analyzed 22 energy efficiency technologies and measures applicable to the processes in the Indian cement industry. The Conservation Supply Curve (CSC) used in this study is an analytical tool that captures both the engineering and the economic perspectives ofmore » energy conservation. Using a bottom-up electricity CSC model and compared to an electricity price forecast the cumulative cost-effective plant-level electricity savings potential for the Indian cement industry for 2010- 2030 is estimated to be 83 TWh, and the cumulative plant-level technical electricity saving potential is 89 TWh during the same period. The grid-level CO2 emissions reduction associated with cost-effective electricity savings is 82 Mt CO2 and the electric grid-level CO2 emission reduction associated with technical electricity saving potential is 88 Mt CO2. Compared to a fuel price forecast, an estimated cumulative cost-effective fuel savings potential of 1,029 PJ with associated CO2 emission reduction of 97 Mt CO2 during 2010-2030 is possible. In addition, a sensitivity analysis with respect to the discount rate used is conducted to assess the effect of changes in this parameter on the results. The result of this study gives a comprehensive and easy to understand perspective to the Indian cement industry and policy makers about the energy efficiency potential and its associated cost over the next twenty years.« less

Ammonia emissions in Europe, part II: How ammonia emission abatement strategies affect secondary aerosols

NASA Astrophysics Data System (ADS)

Backes, Anna M.; Aulinger, Armin; Bieser, Johannes; Matthias, Volker; Quante, Markus

2016-02-01

In central Europe, ammonium sulphate and ammonium nitrate make up a large fraction of fine particles which pose a threat to human health. Most studies on air pollution through particulate matter investigate the influence of emission reductions of sulphur- and nitrogen oxides on aerosol concentration. Here, we focus on the influence of ammonia (NH3) emissions. Emission scenarios have been created on the basis of the improved ammonia emission parameterization implemented in the SMOKE for Europe and CMAQ model systems described in part I of this study. This includes emissions based on future European legislation (the National Emission Ceilings) as well as a dynamic evaluation of the influence of different agricultural sectors (e.g. animal husbandry) on particle formation. The study compares the concentrations of NH3, NH4+, NO3 -, sulphur compounds and the total concentration of particles in winter and summer for a political-, technical- and behavioural scenario. It was found that a reduction of ammonia emissions by 50% lead to a 24% reduction of the total PM2.5 concentrations in northwest Europe. The observed reduction was mainly driven by reduced formation of ammonium nitrate. Moreover, emission reductions during winter had a larger impact than during the rest of the year. This leads to the conclusion that a reduction of the ammonia emissions from the agricultural sector related to animal husbandry could be more efficient than the reduction from other sectors due to its larger share in winter ammonia emissions.

Modelling study of boundary-layer ozone over northern China - Part II: Responses to emission reductions during the Beijing Olympics

NASA Astrophysics Data System (ADS)

Tang, Guiqian; Zhu, Xiaowan; Xin, Jinyuan; Hu, Bo; Song, Tao; Sun, Yang; Wang, Lili; Wu, Fangkun; Sun, Jie; Cheng, Mengtian; Chao, Na; Li, Xin; Wang, Yuesi

2017-09-01

The implementation of emission reduction measures during the Olympics provided a valuable opportunity to study regional photochemical pollution over northern China. In this study, the fifth-generation Pennsylvania State University/National Centre for Atmospheric Research Mesoscale Model and Community Multiscale Air Quality model system was applied to conduct two sets of modelling analyses of the period from July 20 to September 20, 2008, to illustrate the influences of emission reduction measures on regional photochemical pollution over northern China during the Beijing Olympics. The results indicated that the implementation of emission control measures decreased the concentrations of ozone (O3) precursors, namely nitrogen oxide (NOx) and volatile organic compounds (VOCs), throughout the boundary layer. The concentrations of these compounds were reduced by 45% in the central urban area of Beijing at the ground level. Although the average O3 concentration in the central urban area increased by more than 8 ppbv, the total oxidant concentration decreased significantly by more than 5 ppbv. Greater O3 concentrations mainly occurred during periods with weak photochemical reactions. During periods of strong photochemical production, the O3 concentration decreased significantly due to a weakening vertical circulation between the lower and upper boundary layer. Consequently, the number of days when the O3 concentration exceeded 100 ppbv decreased by 25% in Beijing. The emission control measures altered the sensitivity of the regional O3 production. The coordinated control region of NOx and VOCs expanded, and the control region of VOCs decreased in size. The reduction of non-point-source emissions, such as fugitive VOCs and vehicles, was more useful for controlling regional photochemical pollution over northern China.

Energy Saving and GHG Emission Reduction in a Micro-CCHP System by Use of Solar Energy

NASA Astrophysics Data System (ADS)

Ion, Ion V.; Ciocea, Gheorghe; Popescu, Florin

2012-12-01

In this work, the reduction of greenhouse gas emission, and the energy saving by integrating solar collectors and photovoltaic panels in a Stirling engine based microcombined cooling, heating and power (mCCHP) system are studied. The mCCHP system consists of a natural gas Stirling CHP and an adsorber chiller. When the thermal outputs of the Stirling CHP and solar collectors are not sufficient to cover the heat demand for domestic hot water (DHW), heating/cooling, an auxiliary heating boiler starts to operate. The energy saving by using solar energy varies from 13.35% in December to 59.62% in April, in the case of solar collectors usage and from 7.47% in December to 28.27% in July, in the case of photovoltaic panels usage. By using solar energy the annual GHG emission decreases by 31.98% and the fuel cost reduction varies from 12.73% in December to 49.78% in June.

Calculation of energy recovery and greenhouse gas emission reduction from palm oil mill effluent treatment by an anaerobic granular-sludge process.

PubMed

Show, K Y; Ng, C A; Faiza, A R; Wong, L P; Wong, L Y

2011-01-01

Conventional aerobic and low-rate anaerobic processes such as pond and open-tank systems have been widely used in wastewater treatment. In order to improve treatment efficacy and to avoid greenhouse gas emissions, conventional treatment can be upgraded to a high performance anaerobic granular-sludge system. The anaerobic granular-sludge systems are designed to capture the biogas produced, rendering a potential for claims of carbon credits under the Kyoto Protocol for reducing emissions of greenhouse gases. Certified Emission Reductions (CERs) would be issued, which can be exchanged between businesses or bought and sold in international markets at the prevailing market prices. As the advanced anaerobic granular systems are capable of handling high organic loadings concomitant with high strength wastewater and short hydraulic retention time, they render more carbon credits than other conventional anaerobic systems. In addition to efficient waste degradation, the carbon credits can be used to generate revenue and to finance the project. This paper presents a scenario on emission avoidance based on a methane recovery and utilization project. An example analysis on emission reduction and an overview of the global emission market are also outlined.

Comparative effectiveness of two disparate policies on child health: experimental evidence from the Philippines.

PubMed

Peabody, John W; Quimbo, Stella; Florentino, Jhiedon; Shimkhada, Riti; Javier, Xylee; Paculdo, David; Jamison, Dean; Solon, Orville

2017-05-01

Should health systems invest more in access to care by expanding insurance coverage or in health care services including improving the quality of care? Comparing these options experimentally would shed light on the impact and cost-effectiveness of these strategies. The Quality Improvement Demonstration Study (QIDS) was a randomized policy experiment conducted across 30 districts in the Philippines. The study had a control group and two policy intervention groups intended to improve the health of young children. The demand-side intervention in QIDS was universal health insurance coverage (UHC) for children aged 5 years or younger, and a supply-side intervention, a pay-for-performance (P4P) bonus for all providers who met pre-determined quality levels. In this paper, we compare the impacts of these policies from the QIDS experiment on childhood wasting by calculating DALYs averted per US$spent. The direct per capita costs to implement UHC and P4P are US$4.08 and US$1.98 higher, respectively, compared to control. DALYs due to wasting were reduced by 334,862 in UHC and 1,073,185 in P4P. When adjustments are made for the efficiency of higher quality, the DALYS averted per US$ spent is similar in the two arms, 1.56 and 1.58 for UHC and P4P, respectively. Since the P4P quality improvements touches all patients seen by qualifying providers (32% in UHC versus 100% in P4P), there is a larger reduction in DALYs. With similar programmatic costs for either intervention, in this study, each US$spent under P4P yielded 1.52 DALYs averted compared to the standard program, while UHC yielded only a 0.50 DALY reduction. P4P had a greater impact and was more cost-effective compared to UHC as measured by DALYs averted. While expanded insurance benefit ceilings affected only those who are covered, P4P incentivizes practice quality improvement regardless of whether children are insured or uninsured. © The Author 2017. Published by Oxford University Press in association with The London

Comparative effectiveness of two disparate policies on child health: experimental evidence from the Philippines

PubMed Central

Quimbo, Stella; Florentino, Jhiedon; Shimkhada, Riti; Javier, Xylee; Paculdo, David; Jamison, Dean; Solon, Orville

2017-01-01

Abstract Background   Should health systems invest more in access to care by expanding insurance coverage or in health care services including improving the quality of care? Comparing these options experimentally would shed light on the impact and cost-effectiveness of these strategies. Methods   The Quality Improvement Demonstration Study (QIDS) was a randomized policy experiment conducted across 30 districts in the Philippines. The study had a control group and two policy intervention groups intended to improve the health of young children. The demand-side intervention in QIDS was universal health insurance coverage (UHC) for children aged 5 years or younger, and a supply-side intervention, a pay-for-performance (P4P) bonus for all providers who met pre-determined quality levels. In this paper, we compare the impacts of these policies from the QIDS experiment on childhood wasting by calculating DALYs averted per US$spent. Results   The direct per capita costs to implement UHC and P4P are US$4.08 and US$1.98 higher, respectively, compared to control. DALYs due to wasting were reduced by 334,862 in UHC and 1,073,185 in P4P. When adjustments are made for the efficiency of higher quality, the DALYS averted per US$ spent is similar in the two arms, 1.56 and 1.58 for UHC and P4P, respectively. Since the P4P quality improvements touches all patients seen by qualifying providers (32% in UHC versus 100% in P4P), there is a larger reduction in DALYs. With similar programmatic costs for either intervention, in this study, each US$spent under P4P yielded 1.52 DALYs averted compared to the standard program, while UHC yielded only a 0.50 DALY reduction. Conclusion   P4P had a greater impact and was more cost-effective compared to UHC as measured by DALYs averted. While expanded insurance benefit ceilings affected only those who are covered, P4P incentivizes practice quality improvement regardless of whether children are insured or uninsured. PMID:28110265

Climate-driven increase of natural wetland methane emissions offset by human-induced wetland reduction in China over the past three decades

USGS Publications Warehouse

Zhu, Qiuan; Peng, Changhui; Liu, Jinxun; Jiang, Hong; Fang, Xiuqin; Chen, Huai; Niu, Zhichun; Gong, Peng; Lin, Guanghui; Wang, Meng; Yang, Yanzheng; Chang, Jie; Ge, Ying; Xiang, Wenhua; Deng, Xiangwen; He, Jin-Sheng

2016-01-01

Both anthropogenic activities and climate change can affect the biogeochemical processes of natural wetland methanogenesis. Quantifying possible impacts of changing climate and wetland area on wetland methane (CH4) emissions in China is important for improving our knowledge on CH4 budgets locally and globally. However, their respective and combined effects are uncertain. We incorporated changes in wetland area derived from remote sensing into a dynamic CH4 model to quantify the human and climate change induced contributions to natural wetland CH4 emissions in China over the past three decades. Here we found that human-induced wetland loss contributed 34.3% to the CH4 emissions reduction (0.92 TgCH4), and climate change contributed 20.4% to the CH4 emissions increase (0.31 TgCH4), suggesting that decreasing CH4 emissions due to human-induced wetland reductions has offset the increasing climate-driven CH4 emissions. With climate change only, temperature was a dominant controlling factor for wetland CH4 emissions in the northeast (high latitude) and Qinghai-Tibet Plateau (high altitude) regions, whereas precipitation had a considerable influence in relative arid north China. The inevitable uncertainties caused by the asynchronous for different regions or periods due to inter-annual or seasonal variations among remote sensing images should be considered in the wetland CH4 emissions estimation.

Climate-driven increase of natural wetland methane emissions offset by human-induced wetland reduction in China over the past three decades

PubMed Central

Zhu, Qiuan; Peng, Changhui; Liu, Jinxun; Jiang, Hong; Fang, Xiuqin; Chen, Huai; Niu, Zhenguo; Gong, Peng; Lin, Guanghui; Wang, Meng; Wang, Han; Yang, Yanzheng; Chang, Jie; Ge, Ying; Xiang, Wenhua; Deng, Xiangwen; He, Jin-Sheng

2016-01-01

Both anthropogenic activities and climate change can affect the biogeochemical processes of natural wetland methanogenesis. Quantifying possible impacts of changing climate and wetland area on wetland methane (CH4) emissions in China is important for improving our knowledge on CH4 budgets locally and globally. However, their respective and combined effects are uncertain. We incorporated changes in wetland area derived from remote sensing into a dynamic CH4 model to quantify the human and climate change induced contributions to natural wetland CH4 emissions in China over the past three decades. Here we found that human-induced wetland loss contributed 34.3% to the CH4 emissions reduction (0.92 TgCH4), and climate change contributed 20.4% to the CH4 emissions increase (0.31 TgCH4), suggesting that decreasing CH4 emissions due to human-induced wetland reductions has offset the increasing climate-driven CH4 emissions. With climate change only, temperature was a dominant controlling factor for wetland CH4 emissions in the northeast (high latitude) and Qinghai-Tibet Plateau (high altitude) regions, whereas precipitation had a considerable influence in relative arid north China. The inevitable uncertainties caused by the asynchronous for different regions or periods due to inter-annual or seasonal variations among remote sensing images should be considered in the wetland CH4 emissions estimation. PMID:27892535

Fumigation efficacy and emission reduction using low-permeability film in orchard soil fumigation.

PubMed

Gao, Suduan; Sosnoskie, Lynn M; Cabrera, Jose Alfonso; Qin, Ruijun; Hanson, Bradley D; Gerik, James S; Wang, Dong; Browne, Greg T; Thomas, John E

2016-02-01

Many orchards use fumigation to control soilborne pests prior to replanting. Controlling emissions is mandatory to reduce air pollution in California. This research evaluated the effects of plastic film type [polyethylene (PE) or totally impermeable film (TIF)], application rate of Telone C35 [full (610 kg ha(-1) ), 2/3 or 1/3 rates] and carbonation at 207 kPa on fumigant transport (emission and in soil) and efficacy. While increasing fumigant concentrations under the tarp, TIF reduced emissions >95% (∼2% and <1% of total applied 1,3-dichloropropene and chloropicrin respectively) relative to bare soil, compared with ∼30% reduction by PE. All fumigation treatments, regardless of film type, provided good nematode control above 100 cm soil depth; however, nematode survival was high at deeper depths. Weed emergence was mostly affected by tarping and fumigant rate, with no effects from the carbonation. TIF can effectively reduce fumigant emissions. Carbonation under the studied conditions did not improve fumigant dispersion and pest control. The 2/3 rate with TIF controlled nematodes as effectively as the full rate in bare soil or under the PE film to 100 cm soil depth. However, control of nematodes in deeper soil remains a challenge for perennial crops. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

Universal health coverage at the macro level: Synthetic control evidence from Thailand.

PubMed

Rieger, Matthias; Wagner, Natascha; Bedi, Arjun S

2017-01-01

As more and more countries are moving towards Universal Health Coverage (UHC), it is important to understand the macro level or aggregate impacts of such a policy. We use synthetic control methods to study the impact of UHC, introduced in Thailand in 2001, on various macroeconomic and health outcomes. Thailand is compared to a weighted average of control countries in terms of aggregate health financing indicators, aggregate health outcomes and economic performance, over the period 1995 to 2012. Our results suggest that UHC helps alleviate the financial consequences of illnesses. The estimated treatment effect of UHC on out-of-pocket payments as a percentage of overall health expenditures is negative 13 percentage points and its effect on annual government per capita health spending is US$ 79. We detect a smaller effect of US$ 60.8 on total health spending per capita which appears with a lag. We document positive health effects as captured by reductions in infant and child mortality. We do not find any effect on GDP and the share of the government budget devoted to health. Overall, our results complement micro evidence based on within country variation. The counterfactual design implemented here may be used to inform other countries on the macro level repercussions of UHC. Copyright © 2016. Published by Elsevier Ltd.

Effects of Nano Additives in engine emission Characteristics using Blends of Lemon Balm oil with Diesel

NASA Astrophysics Data System (ADS)

Senthil kumar, J.; Ganesan, S.; Sivasaravanan, S.; Padmanabhan, S.; Krishnan, L.; Aniruthan, V. C.

2017-05-01

Economic growth in developing countries has led to enormous increase in energy demand. In India the energy demand is increasing at a rate of 6.5% every year. The crude oil demand of country is meet by bring in of about 70%. Thus the energy safety measures have become key issue for our country. Bio diesel an eco-friendly and renewable fuel alternate for diesel has been getting the consideration of researcher’s entire world. The main aim of this paper is to evaluate the engine parameters using blend of pure lemon balm oil with diesel. Also nano Additives is used as a catalyst with blends of bio fuel to enhance the Emission Characteristics of various effective gases like CO2, NOx, CO and UHC with various levels of engine process parameters.

10 CFR 300.8 - Calculating emission reductions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... household operation; and (4) A description of the emission sources or sinks covered, such as fossil fuel... the specific form of benefit or relief provided. (k) Determining the entity responsible for emission...

10 CFR 300.8 - Calculating emission reductions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... household operation; and (4) A description of the emission sources or sinks covered, such as fossil fuel... the specific form of benefit or relief provided. (k) Determining the entity responsible for emission...

10 CFR 300.8 - Calculating emission reductions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... household operation; and (4) A description of the emission sources or sinks covered, such as fossil fuel... the specific form of benefit or relief provided. (k) Determining the entity responsible for emission...

10 CFR 300.8 - Calculating emission reductions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... household operation; and (4) A description of the emission sources or sinks covered, such as fossil fuel... the specific form of benefit or relief provided. (k) Determining the entity responsible for emission...

10 CFR 300.8 - Calculating emission reductions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... household operation; and (4) A description of the emission sources or sinks covered, such as fossil fuel... the specific form of benefit or relief provided. (k) Determining the entity responsible for emission...

Power plant emissions reduction

DOEpatents

Anand, Ashok Kumar; Nagarjuna Reddy, Thirumala Reddy

2015-10-20

A system for improved emissions performance of a power plant generally includes an exhaust gas recirculation system having an exhaust gas compressor disposed downstream from the combustor, a condensation collection system at least partially disposed upstream from the exhaust gas compressor, and a mixing chamber in fluid communication with the exhaust gas compressor and the condensation collection system, where the mixing chamber is in fluid communication with the combustor.

A Consideration on Service Business Model for Saving Energy and Reduction of CO2 Emissions Using Inverters

NASA Astrophysics Data System (ADS)

Kosaka, Michitaka; Yabutani, Takashi

This paper considers the effectiveness of service business approach for reducing CO2 emission. “HDRIVE” is a service business using inverters to reduce energy consumption of motor drive. The business model of this service is changed for finding new opportunities of CO2 emission reduction by combining various factors such as financial service or long-term service contract. Risk analysis of this business model is very important for giving stable services to users for long term. HDRIVE business model is found to be suitable for this objective. This service can be applied to the industries such as chemical or steel industry effectively, where CO2 emission is very large, and has the possibility of creating new business considering CDM or trading CO2 emission right. The effectiveness of this approach is demonstrated through several examples in real business.

Impacts of Vehicle Weight Reduction via Material Substitution on Life-Cycle Greenhouse Gas Emissions.

PubMed

Kelly, Jarod C; Sullivan, John L; Burnham, Andrew; Elgowainy, Amgad

2015-10-20

This study examines the vehicle-cycle and vehicle total life-cycle impacts of substituting lightweight materials into vehicles. We determine part-based greenhouse gas (GHG) emission ratios by collecting material substitution data and evaluating that alongside known mass-based GHG ratios (using and updating Argonne National Laboratory's GREET model) associated with material pair substitutions. Several vehicle parts are lightweighted via material substitution, using substitution ratios from a U.S. Department of Energy report, to determine GHG emissions. We then examine fuel-cycle GHG reductions from lightweighting. The fuel reduction value methodology is applied using FRV estimates of 0.15-0.25, and 0.25-0.5 L/(100km·100 kg), with and without powertrain adjustments, respectively. GHG breakeven values are derived for both driving distance and material substitution ratio. While material substitution can reduce vehicle weight, it often increases vehicle-cycle GHGs. It is likely that replacing steel (the dominant vehicle material) with wrought aluminum, carbon fiber reinforced plastic (CRFP), or magnesium will increase vehicle-cycle GHGs. However, lifetime fuel economy benefits often outweigh the vehicle-cycle, resulting in a net total life-cycle GHG benefit. This is the case for steel replaced by wrought aluminum in all assumed cases, and for CFRP and magnesium except for high substitution ratio and low FRV.

Applying a systems approach to assess carbon emission reductions from climate change mitigation in Mexico’s forest sector

NASA Astrophysics Data System (ADS)

Olguin, Marcela; Wayson, Craig; Fellows, Max; Birdsey, Richard; Smyth, Carolyn E.; Magnan, Michael; Dugan, Alexa J.; Mascorro, Vanessa S.; Alanís, Armando; Serrano, Enrique; Kurz, Werner A.

2018-03-01

The Paris Agreement of the United Nation Framework Convention on Climate Change calls for a balance of anthropogenic greenhouse emissions and removals in the latter part of this century. Mexico indicated in its Intended Nationally Determined Contribution and its Climate Change Mid-Century Strategy that the land sector will contribute to meeting GHG emission reduction goals. Since 2012, the Mexican government through its National Forestry Commission, with international financial and technical support, has been developing carbon dynamics models to explore climate change mitigation options in the forest sector. Following a systems approach, here we assess the biophysical mitigation potential of forest ecosystems, harvested wood products and their substitution benefits (i.e. the change in emissions resulting from substitution of wood for more emissions-intensive products and fossil fuels), for policy alternatives considered by the Mexican government, such as a net zero deforestation rate and sustainable forest management. We used available analytical frameworks (Carbon Budget Model of the Canadian Forest Sector and a harvested wood products model), parameterized with local input data in two contrasting Mexican states. Using information from the National Forest Monitoring System (e.g. forest inventories, remote sensing, disturbance data), we demonstrate that activities aimed at reaching a net-zero deforestation rate can yield significant CO2e mitigation benefits by 2030 and 2050 relative to a baseline scenario (‘business as usual’), but if combined with increasing forest harvest to produce long-lived products and substitute more energy-intensive materials, emissions reductions could also provide other co-benefits (e.g. jobs, illegal logging reduction). We concluded that the relative impact of mitigation activities is locally dependent, suggesting that mitigation strategies should be designed and implemented at sub-national scales. We were also encouraged about the

A modeling comparison of deep greenhouse gas emissions reduction scenarios by 2030 in California

DOE PAGES

Yeh, Sonia; Yang, Christopher; Gibbs, Michael; ...

2016-10-21

California aims to reduce greenhouse gas (GHG) emissions to 40% below 1990 levels by 2030. We compare six energy models that have played various roles in informing the state policymakers in setting climate policy goals and targets. These models adopt a range of modeling structures, including stock-turnover back-casting models, a least-cost optimization model, macroeconomic/macro-econometric models, and an electricity dispatch model. Results from these models provide useful insights in terms of the transformations in the energy system required, including efficiency improvements in cars, trucks, and buildings, electrification of end-uses, low- or zero-carbon electricity and fuels, aggressive adoptions of zero-emission vehicles (ZEVs),more » demand reduction, and large reductions of non-energy GHG emissions. Some of these studies also suggest that the direct economic costs can be fairly modest or even generate net savings, while the indirect macroeconomic benefits are large, as shifts in employment and capital investments could have higher economic returns than conventional energy expenditures. These models, however, often assume perfect markets, perfect competition, and zero transaction costs. They also do not provide specific policy guidance on how these transformative changes can be achieved. Greater emphasis on modeling uncertainty, consumer behaviors, heterogeneity of impacts, and spatial modeling would further enhance policymakers' ability to design more effective and targeted policies. Here, this paper presents an example of how policymakers, energy system modelers and stakeholders interact and work together to develop and evaluate long-term state climate policy targets. Lastly, even though this paper focuses on California, the process of dialogue and interactions, modeling results, and lessons learned can be generally adopted across different regions and scales.« less

Effectiveness of selective catalytic reduction systems on reducing gaseous emissions from an engine using diesel and biodiesel blends.

PubMed

Borillo, Guilherme C; Tadano, Yara S; Godoi, Ana F L; Santana, Simone S M; Weronka, Fernando M; Penteado Neto, Renato A; Rempel, Dennis; Yamamoto, Carlos I; Potgieter-Vermaak, Sanja; Potgieter, Johannes H; Godoi, Ricardo H M

2015-03-03

The aim of this investigation was to quantify organic and inorganic gas emissions from a four-cylinder diesel engine equipped with a urea selective catalytic reduction (SCR) system. Using a bench dynamometer, the emissions from the following mixtures were evaluated using a Fourier transform infrared (FTIR) spectrometer: low-sulfur diesel (LSD), ultralow-sulfur diesel (ULSD), and a blend of 20% soybean biodiesel and 80% ULSD (B20). For all studied fuels, the use of the SCR system yielded statistically significant (p < 0.05) lower NOx emissions. In the case of the LSD and ULSD fuels, the SCR system also significantly reduced emissions of compounds with high photochemical ozone creation potential, such as formaldehyde. However, for all tested fuels, the SCR system produced significantly (p < 0.05) higher emissions of N2O. In the case of LSD, the NH3 emissions were elevated, and in the case of ULSD and B20 fuels, the non-methane hydrocarbon (NMHC) and total hydrocarbon of diesel (HCD) emissions were significantly higher.

[Research on contribution decomposition by industry to China's carbon intensity reduction and carbon emission growth].

PubMed

Jiang, Jing-Jing; Ye, Bin; Ji, Jun-Ping; Ma, Xiao-Ming

2014-11-01

The binding carbon intensity index and the pilot "cap-and-trade" emission trading scheme are two important approaches currently applied by China to mitigate its greenhouse gases emissions. It is of great significance to research the influence mechanism of related factors by industry on the dynamics of national carbon intensity and emission, not only for setting industry-specified intensity reduction target but also for setting industry coverage of the ETS. Two LMDI models were applied in this paper to decompose industry contributions to the changes of China's carbon intensity and carbon emission during the period of 1996-2010. Empirical results showed that: The decline of national carbon intensity was jointly determined by the changes of carbon intensities and the added value proportions of all industries, and the impact of industry carbon intensities was larger. The increase of national carbon emission was jointly determined by the changes of carbon intensities and the added value of all industries. The former had inhibitory effect whist the latter had decisive promoting effect. The five industries making the largest contribution to the changes of national carbon emission and carbon intensity included industries of electricity, nonmetal mineral, ferrous metal, transportation service, chemical materials, which were followed by the industries of agriculture, coal mining and processing, petroleum and natural gas extraction. Petroleum refining and coking industry and construction industry made small contribution to the decline of national carbon intensity, but made large contribution to the growth of national carbon emission. The contributions of service industries to national carbon emission growth showed a rising trend, especially those of transportation service industry, wholesaling, retailing and catering service industry.

Black carbon emissions in gasoline exhaust and a reduction alternative with a gasoline particulate filter.

PubMed

Chan, Tak W; Meloche, Eric; Kubsh, Joseph; Brezny, Rasto

2014-05-20

Black carbon (BC) mass and solid particle number emissions were obtained from two pairs of gasoline direct injection (GDI) vehicles and port fuel injection (PFI) vehicles over the U.S. Federal Test Procedure 75 (FTP-75) and US06 Supplemental Federal Test Procedure (US06) drive cycles on gasoline and 10% by volume blended ethanol (E10). BC solid particles were emitted mostly during cold-start from all GDI and PFI vehicles. The reduction in ambient temperature had significant impacts on BC mass and solid particle number emissions, but larger impacts were observed on the PFI vehicles than the GDI vehicles. Over the FTP-75 phase 1 (cold-start) drive cycle, the BC mass emissions from the two GDI vehicles at 0 °F (-18 °C) varied from 57 to 143 mg/mi, which was higher than the emissions at 72 °F (22 °C; 12-29 mg/mi) by a factor of 5. For the two PFI vehicles, the BC mass emissions over the FTP-75 phase 1 drive cycle at 0 °F varied from 111 to 162 mg/mi, higher by a factor of 44-72 when compared to the BC emissions of 2-4 mg/mi at 72 °F. The use of a gasoline particulate filter (GPF) reduced BC emissions from the selected GDI vehicle by 73-88% at various ambient temperatures over the FTP-75 phase 1 drive cycle. The ambient temperature had less of an impact on particle emissions for a warmed-up engine. Over the US06 drive cycle, the GPF reduced BC mass emissions from the GDI vehicle by 59-80% at various temperatures. E10 had limited impact on BC emissions from the selected GDI and PFI vehicles during hot-starts. E10 was found to reduce BC emissions from the GDI vehicle by 15% at standard temperature and by 75% at 19 °F (-7 °C).

A Fe-C-Ca big cycle in modern carbon-intensive industries: toward emission reduction and resource utilization

PubMed Central

Sun, Yongqi; Sridhar, Seetharaman; Seetharaman, Seshadri; Wang, Hao; Liu, Lili; Wang, Xidong; Zhang, Zuotai

2016-01-01

Herein a big Fe-C-Ca cycle, clarifying the basic element flows and energy flows in modern carbon-intensive industries including the metallurgical industry and the cement industry, was proposed for the first time in the contexts of emission reduction and iron ore degradation nowadays. This big cycle was focused on three industrial elements of Fe, C and Ca and thus it mainly comprised three interdependent loops, i.e., a C-cycle, a Fe-cycle and a Ca-path. As exemplified, we started from the integrated disposal of hot steel slags, a man-made iron resource via char gasification and the employment of hematite, a natural iron resource greatly extended the application area of this idea. Accordingly, based on this concept, the theoretical potentials for energy saving, emission reduction and Fe resource recovery achieved in modern industry are estimated up to 7.66 Mt of standard coal, 63.9 Mt of CO2 and 25.2 Mt of pig iron, respectively. PMID:26923104

A Fe-C-Ca big cycle in modern carbon-intensive industries: toward emission reduction and resource utilization

NASA Astrophysics Data System (ADS)

Sun, Yongqi; Sridhar, Seetharaman; Seetharaman, Seshadri; Wang, Hao; Liu, Lili; Wang, Xidong; Zhang, Zuotai

2016-02-01

Herein a big Fe-C-Ca cycle, clarifying the basic element flows and energy flows in modern carbon-intensive industries including the metallurgical industry and the cement industry, was proposed for the first time in the contexts of emission reduction and iron ore degradation nowadays. This big cycle was focused on three industrial elements of Fe, C and Ca and thus it mainly comprised three interdependent loops, i.e., a C-cycle, a Fe-cycle and a Ca-path. As exemplified, we started from the integrated disposal of hot steel slags, a man-made iron resource via char gasification and the employment of hematite, a natural iron resource greatly extended the application area of this idea. Accordingly, based on this concept, the theoretical potentials for energy saving, emission reduction and Fe resource recovery achieved in modern industry are estimated up to 7.66 Mt of standard coal, 63.9 Mt of CO2 and 25.2 Mt of pig iron, respectively.

Numerical investigation of the efficiency of emission reduction and heat extraction in a sedimentary geothermal reservoir: a case study of the Daming geothermal field in China.

PubMed

Guo, Xuyang; Song, Hongqing; Killough, John; Du, Li; Sun, Pengguang

2018-02-01

The utilization of geothermal energy is clean and has great potential worldwide, and it is important to utilize geothermal energy in a sustainable manner. Mathematical modeling studies of geothermal reservoirs are important as they evaluate and quantify the complex multi-physical effects in geothermal reservoirs. However, previous modeling efforts lack the study focusing on the emission reduction efficiency and the deformation at geothermal wellbores caused by geothermal water extraction/circulation. Emission efficiency is rather relevant in geothermal projects introduced in areas characterized by elevated air pollution where the utilization of geothermal energy is as an alternative to burning fossil fuels. Deformation at geothermal wellbores is also relevant as significant deformation caused by water extraction can lead to geothermal wellbore instability and can consequently decrease the effectiveness of the heat extraction process in geothermal wells. In this study, the efficiency of emission reduction and heat extraction in a sedimentary geothermal reservoir in Daming County, China, are numerically investigated based on a coupled multi-physical model. Relationships between the efficiency of emission reduction and heat extraction, deformation at geothermal well locations, and geothermal field parameters including well spacing, heat production rate, re-injection temperature, rock stiffness, and geothermal well placement patterns are analyzed. Results show that, although large heat production rates and low re-injection temperatures can lead to decreased heat production in the last 8 years of heat extraction, they still improve the overall heat production capacity and emission reduction capacity. Also, the emission reduction capacity is positively correlated with the heat production capacity. Deformation at geothermal wellbore locations is alleviated by smaller well spacing, lower heat production rates, and smaller numbers of injectors in the well pattern, and by

Environmentally Responsible Aviation: Propulsion Research to Enable Fuel Burn, Noise and Emissions Reduction

NASA Technical Reports Server (NTRS)

Van Zante, Dale; Suder, Kenneth

2015-01-01

The NASA Environmentally Responsible Aviation (ERA) program is maturing technologies to enable simultaneous reduction of fuel burn, noise and emissions from an aircraft engine system. Three engine related Integrated Technology Demonstrations (ITDs) have been completed at Glenn Research Center in collaboration with Pratt Whitney, General Electric and the Federal Aviation Administration. The engine technologies being matured are: a low NOx, fuel flexible combustor in partnership with Pratt Whitney; an ultra-high bypass, ducted propulsor system in partnership with Pratt Whitney and FAA; and high pressure ratio, front-stage core compressor technology in partnership with General Electric. The technical rationale, test configurations and overall results from the test series in each ITD are described. ERA is using system analysis to project the benefits of the ITD technologies on potential aircraft systems in the 2025 timeframe. Data from the ITD experiments were used to guide the system analysis assumptions. Results from the current assessments for fuel burn, noise and oxides of nitrogen emissions are presented.

Environmentally Responsible Aviation: Propulsion Research to Enable Fuel Burn, Noise and Emissions Reduction

NASA Technical Reports Server (NTRS)

Van Zante, Dale E.; Suder, Kenneth L.

2015-01-01

The NASA Environmentally Responsible Aviation (ERA) program is maturing technologies to enable simultaneous reduction of fuel burn, noise and emissions from an aircraft engine system. Three engine related Integrated Technology Demonstrations (ITDs) have been completed at Glenn Research Center in collaboration with Pratt Whitney, General Electric and the Federal Aviation Administration. The engine technologies being matured are a low NOx, fuel flexible combustor in partnership with Pratt Whitney, an ultra-high bypass, ducted propulsor system in partnership with Pratt Whitney FAA and high pressure ratio, front-stage core compressor technology in partnership with General Electric. The technical rationale, test configurations and overall results from the test series in each ITD are described. ERA is using system analysis to project the benefits of the ITD technologies on potential aircraft systems in the 2025 timeframe. Data from the ITD experiments were used to guide the system analysis assumptions. Results from the current assessments for fuel burn, noise and oxides of nitrogen emissions are presented.

Reduction of Life Cycle CO2 Emission in Public Welfare Facilities Equipped with PV/Solar Heat/Cogeneration System

NASA Astrophysics Data System (ADS)

Oke, Shinichiro; Kemmoku, Yoshishige; Takikawa, Hirofumi; Sakakibara, Tateki

The reduction effect of life cycle CO2 emission is examined in case of introducing a PV/solar heat/cogeneration system into public welfare facilities(hotel and hospital). Life cycle CO2 emission is calculated as the sum of that when operating and that when manufacturing equipments. The system is operated with the dynamic programming method, into which hourly data of electric and heat loads, solar insolation, and atmospheric temperature during a year are input. The proposed system is compared with a conventional system and a cogeneration system. The life cycle CO2 emission of the PV/solar heat/cogeneration system is lower than that of the conventional system by 20% in hotel and by 14% in hospital.

Study of strains of Candida spp. Isolated from catheters in UHC of Oran (Algeria): Identification and antifungal susceptibility.

PubMed

Bendjelloul, M; Boucherit-Otmani, Z; Boucherit, K

2016-09-01

The increasing incidence of Candida spp., and the vital prognosis often compromise for patients with Candida species make urgent the exact knowledge of their distribution worldwide and exhaust action antifungals currently used in clinical. That why we carry out an epidemiological study of Candida species and testing their susceptibility against two antifungals: amphotericin B and caspofungin. Samplings of peripheral venous catheters (PVC) were carried out from during 8months on the services of Internal medicine, Surgery A and Neonatology of Oran's University Hospital Center (UHC). The study of the susceptibility of Candida species to antifungal agents was performed according to the Clinical Laboratory Standards Institute (CLSI 2008). From 300 samples, 25 yeasts were isolated. The rate of colonization PVC was 8.33% by Candida spp. The most isolated strains were Candida parapsilosis with 64% of cases, followed by Candida albicans (12%) then 8% for Candida glabrata and Candida krusei. However, only 4% of isolates were Candida famata or Candida lusitaniae. Furthermore all isolated strains were susceptible to amphotericin B with Minimum Inhibitory Concentrations (MIC) ranging from 0.25 to 1μg/mL. MIC obtained with caspofungin vary from 0.0625 to 2μg/mL for all strains. Moreover, one strain of C. krusei is resistant to caspofungin with a MIC superior to 8μg/mL. All though caspofungin is at least as effective as amphotericin B, it is better tolerated for the treatment of invasive fungal infections. Copyright © 2016. Published by Elsevier Masson SAS.

Photochemical modeling in California with two chemical mechanisms: model intercomparison and response to emission reductions.

PubMed

Cai, Chenxia; Kelly, James T; Avise, Jeremy C; Kaduwela, Ajith P; Stockwell, William R

2011-05-01

An updated version of the Statewide Air Pollution Research Center (SAPRC) chemical mechanism (SAPRC07C) was implemented into the Community Multiscale Air Quality (CMAQ) version 4.6. CMAQ simulations using SAPRC07C and the previously released version, SAPRC99, were performed and compared for an episode during July-August, 2000. Ozone (O3) predictions of the SAPRC07C simulation are generally lower than those of the SAPRC99 simulation in the key areas of central and southern California, especially in areas where modeled concentrations are greater than the federal 8-hr O3 standard of 75 parts per billion (ppb) and/or when the volatile organic compound (VOC)/nitrogen oxides (NOx) ratio is less than 13. The relative changes of ozone production efficiency (OPE) against the VOC/NOx ratio at 46 sites indicate that the OPE is reduced in SAPRC07C compared with SAPRC99 at most sites by as much as approximately 22%. The SAPRC99 and SAPRC07C mechanisms respond similarly to 20% reductions in anthropogenic VOC emissions. The response of the mechanisms to 20% NOx emissions reductions can be grouped into three cases. In case 1, in which both mechanisms show a decrease in daily maximum 8-hr O3 concentration with decreasing NOx emissions, the O3 decrease in SAPRC07C is smaller. In case 2, in which both mechanisms show an increase in O3 with decreasing NOx emissions, the O3 increase is larger in SAPRC07C. In case 3, SAPRC07C simulates an increase in O3 in response to reduced NOx emissions whereas SAPRC99 simulates a decrease in O3 for the same region. As a result, the areas where NOx controls would be disbeneficial are spatially expanded in SAPRC07C. Although the results presented here are valuable for understanding differences in predictions and model response for SAPRC99 and SAPRC07C, the study did not evaluate the impact of mechanism differences in the context of the U.S. Environmental Protection Agency's guidance for using numerical models in demonstrating air quality attainment

Developments in greenhouse gas emissions and net energy use in Danish agriculture - how to achieve substantial CO(2) reductions?

PubMed

Dalgaard, T; Olesen, J E; Petersen, S O; Petersen, B M; Jørgensen, U; Kristensen, T; Hutchings, N J; Gyldenkærne, S; Hermansen, J E

2011-11-01

Greenhouse gas (GHG) emissions from agriculture are a significant contributor to total Danish emissions. Consequently, much effort is currently given to the exploration of potential strategies to reduce agricultural emissions. This paper presents results from a study estimating agricultural GHG emissions in the form of methane, nitrous oxide and carbon dioxide (including carbon sources and sinks, and the impact of energy consumption/bioenergy production) from Danish agriculture in the years 1990-2010. An analysis of possible measures to reduce the GHG emissions indicated that a 50-70% reduction of agricultural emissions by 2050 relative to 1990 is achievable, including mitigation measures in relation to the handling of manure and fertilisers, optimization of animal feeding, cropping practices, and land use changes with more organic farming, afforestation and energy crops. In addition, the bioenergy production may be increased significantly without reducing the food production, whereby Danish agriculture could achieve a positive energy balance. Copyright © 2011 Elsevier Ltd. All rights reserved.

Particulate emissions from diesel engines: correlation between engine technology and emissions

PubMed Central

2014-01-01

In the last 30 years, diesel engines have made rapid progress to increased efficiency, environmental protection and comfort for both light- and heavy-duty applications. The technical developments include all issues from fuel to combustion process to exhaust gas aftertreatment. This paper provides a comprehensive summary of the available literature regarding technical developments and their impact on the reduction of pollutant emission. This includes emission legislation, fuel quality, diesel engine- and exhaust gas aftertreatment technologies, as well as particulate composition, with a focus on the mass-related particulate emission of on-road vehicle applications. Diesel engine technologies representative of real-world on-road applications will be highlighted. Internal engine modifications now make it possible to minimize particulate and nitrogen oxide emissions with nearly no reduction in power. Among these modifications are cooled exhaust gas recirculation, optimized injections systems, adapted charging systems and optimized combustion processes with high turbulence. With introduction and optimization of exhaust gas aftertreatment systems, such as the diesel oxidation catalyst and the diesel particulate trap, as well as NOx-reduction systems, pollutant emissions have been significantly decreased. Today, sulfur poisoning of diesel oxidation catalysts is no longer considered a problem due to the low-sulfur fuel used in Europe. In the future, there will be an increased use of bio-fuels, which generally have a positive impact on the particulate emissions and do not increase the particle number emissions. Since the introduction of the EU emissions legislation, all emission limits have been reduced by over 90%. Further steps can be expected in the future. Retrospectively, the particulate emissions of modern diesel engines with respect to quality and quantity cannot be compared with those of older engines. Internal engine modifications lead to a clear reduction of the

Particulate emissions from diesel engines: correlation between engine technology and emissions.

PubMed

Fiebig, Michael; Wiartalla, Andreas; Holderbaum, Bastian; Kiesow, Sebastian

2014-03-07

In the last 30 years, diesel engines have made rapid progress to increased efficiency, environmental protection and comfort for both light- and heavy-duty applications. The technical developments include all issues from fuel to combustion process to exhaust gas aftertreatment. This paper provides a comprehensive summary of the available literature regarding technical developments and their impact on the reduction of pollutant emission. This includes emission legislation, fuel quality, diesel engine- and exhaust gas aftertreatment technologies, as well as particulate composition, with a focus on the mass-related particulate emission of on-road vehicle applications. Diesel engine technologies representative of real-world on-road applications will be highlighted.Internal engine modifications now make it possible to minimize particulate and nitrogen oxide emissions with nearly no reduction in power. Among these modifications are cooled exhaust gas recirculation, optimized injections systems, adapted charging systems and optimized combustion processes with high turbulence. With introduction and optimization of exhaust gas aftertreatment systems, such as the diesel oxidation catalyst and the diesel particulate trap, as well as NOx-reduction systems, pollutant emissions have been significantly decreased. Today, sulfur poisoning of diesel oxidation catalysts is no longer considered a problem due to the low-sulfur fuel used in Europe. In the future, there will be an increased use of bio-fuels, which generally have a positive impact on the particulate emissions and do not increase the particle number emissions.Since the introduction of the EU emissions legislation, all emission limits have been reduced by over 90%. Further steps can be expected in the future. Retrospectively, the particulate emissions of modern diesel engines with respect to quality and quantity cannot be compared with those of older engines. Internal engine modifications lead to a clear reduction of the

Combustion performance evaluation of air staging of palm oil blends.

PubMed

Mohd Jaafar, Mohammad Nazri; Eldrainy, Yehia A; Mat Ali, Muhammad Faiser; Wan Omar, W Z; Mohd Hizam, Mohd Faizi Arif

2012-02-21

The problems of global warming and the unstable price of petroleum oils have led to a race to develop environmentally friendly biofuels, such as palm oil or ethanol derived from corn and sugar cane. Biofuels are a potential replacement for fossil fuel, since they are renewable and environmentally friendly. This paper evaluates the combustion performance and emission characteristics of Refined, Bleached, and Deodorized Palm Oil (RBDPO)/diesel blends B5, B10, B15, B20, and B25 by volume, using an industrial oil burner with and without secondary air. Wall temperature profiles along the combustion chamber axis were measured using a series of thermocouples fitted axially on the combustion chamber wall, and emissions released were measured using a gas analyzer. The results show that RBDPO blend B25 produced the maximum emission reduction of 56.9% of CO, 74.7% of NOx, 68.5% of SO(2), and 77.5% of UHC compared to petroleum diesel, while air staging (secondary air) in most cases reduces the emissions further. However, increasing concentrations of RBDPO in the blends also reduced the energy released from the combustion. The maximum wall temperature reduction was 62.7% for B25 at the exit of the combustion chamber.

Analysis on carbon dioxide emission reduction during the anaerobic synergetic digestion technology of sludge and kitchen waste: Taking kitchen waste synergetic digestion project in Zhenjiang as an example.

PubMed

Guo, Qia; Dai, Xiaohu

2017-11-01

With the popularization of municipal sewage treatment facilities, the improvement of sewage treatment efficiency and the deepening degree of sewage treatment, the sludge production of sewage plant has been sharply increased. Carbon emission during the process of municipal sewage treatment and disposal has become one of the important sources of greenhouse gases that cause greenhouse effect. How to reduce carbon dioxide emissions during sewage treatment and disposal process is of great significance for reducing air pollution. Kitchen waste and excess sludge, as two important organic wastes, once uses anaerobic synergetic digestion technology in the treatment process can on the one hand, avoid instability of sludge individual anaerobic digestion, improve sludge degradation rate and marsh gas production rate, and on the other hand, help increase the reduction of carbon dioxide emissions to a great extent. The paper uses material balance method, analyzes and calculates the carbon dioxide emissions from kitchen waste and sludge disposed by the anaerobic synergetic digestion technology, compares the anaerobic synergetic digestion technology with traditional sludge sanitary landfill technology and works out the carbon dioxide emission reductions after synergetic digestion. It takes the kitchen waste and sludge synergetic digestion engineering project of Zhenjiang city in Jiangsu province as an example, makes material balance analysis using concrete data and works out the carbon dioxide daily emission reductions. The paper analyzes the actual situation of emission reduction by comparing the data, and found that the synergetic digestion of kitchen waste and sludge can effectively reduce the carbon dioxide emission, and the reduction is obvious especially compared with that of sludge sanitary landfill, which has a certain effect on whether to promote the use of the technology. Copyright © 2017 Elsevier Ltd. All rights reserved.

A case study of the relative effects of power plant nitrogen oxides and sulfur dioxide emission reductions on atmospheric nitrogen deposition.

PubMed

Vijayaraghavan, Krish; Seigneur, Christian; Bronson, Rochelle; Chen, Shu-Yun; Karamchandani, Prakash; Walters, Justin T; Jansen, John J; Brandmeyer, Jo Ellen; Knipping, Eladio M

2010-03-01

The contrasting effects of point source nitrogen oxides (NOx) and sulfur dioxide (SO2) air emission reductions on regional atmospheric nitrogen deposition are analyzed for the case study of a coal-fired power plant in the southeastern United States. The effect of potential emission reductions at the plant on nitrogen deposition to Escambia Bay and its watershed on the Florida-Alabama border is simulated using the three-dimensional Eulerian Community Multiscale Air Quality (CMAQ) model. A method to quantify the relative and individual effects of NOx versus SO2 controls on nitrogen deposition using air quality modeling results obtained from the simultaneous application of NOx and SO2 emission controls is presented and discussed using the results from CMAQ simulations conducted with NOx-only and SO2-only emission reductions; the method applies only to cases in which ambient inorganic nitrate is present mostly in the gas phase; that is, in the form of gaseous nitric acid (HNO3). In such instances, the individual effects of NOx and SO2 controls on nitrogen deposition can be approximated by the effects of combined NOx + SO2 controls on the deposition of NOy, (the sum of oxidized nitrogen species) and reduced nitrogen species (NHx), respectively. The benefit of controls at the plant in terms of the decrease in nitrogen deposition to Escambia Bay and watershed is less than 6% of the overall benefit due to regional Clean Air Interstate Rule (CAIR) controls.

Coordinated EV adoption: double-digit reductions in emissions and fuel use for $40/vehicle-year.

PubMed

Choi, Dong Gu; Kreikebaum, Frank; Thomas, Valerie M; Divan, Deepak

2013-09-17

Adoption of electric vehicles (EVs) would affect the costs and sources of electricity and the United States efficiency requirements for conventional vehicles (CVs). We model EV adoption scenarios in each of six regions of the Eastern Interconnection, containing 70% of the United States population. We develop electricity system optimization models at the multidecade, day-ahead, and hour-ahead time scales, incorporating spatial wind energy modeling, endogenous modeling of CV efficiencies, projections for EV efficiencies, and projected CV and EV costs. We find two means to reduce total consumer expenditure (TCE): (i) controlling charge timing and (ii) unlinking the fuel economy regulations for CVs from EVs. Although EVs provide minimal direct GHG reductions, controlled charging provides load flexibility, lowering the cost of renewable electricity. Without EVs, a 33% renewable electricity standard (RES) would cost $193/vehicle-year more than the reference case (10% RES). Combining a 33% RES, EVs with controlled charging and unlinking would reduce combined electric- and vehicle-sector CO2 emissions by 27% and reduce gasoline consumption by 59% for $40/vehicle-year more than the reference case. Coordinating EV adoption with adoption of controlled charging, unlinked fuel economy regulations, and renewable electricity standards would provide low-cost reductions in emissions and fuel usage.

Emerging Energy-efficiency and CO{sub 2} Emission-reduction Technologies for Cement and Concrete Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasanbeigi, Ali; Price, Lynn; Lin, Elina

2012-04-06

Globally, the cement industry accounts for approximately 5 percent of current anthropogenic carbon dioxide (CO{sub 2}) emissions. World cement demand and production are increasing significantly, leading to an increase in this industry's absolute energy use and CO{sub 2} emissions. Development of new energy-efficiency and CO{sub 2} emission-reduction technologies and their deployment in the market will be key for the cement industry's mid- and long-term climate change mitigation strategies. This report is an initial effort to compile available information on process description, energy savings, environmental and other benefits, costs, commercialization status, and references for emerging technologies to reduce the cement industry'smore » energy use and CO{sub 2} emissions. Although studies from around the world identify a variety of sector-specific and cross-cutting energy-efficiency technologies for the cement industry that have already been commercialized, information is scarce and/or scattered regarding emerging or advanced energy-efficiency and low-carbon technologies that are not yet commercialized. This report consolidates available information on nineteen emerging technologies for the cement industry, with the goal of providing engineers, researchers, investors, cement companies, policy makers, and other interested parties with easy access to a well-structured database of information on these technologies.« less

Greenhouse gas emission reductions from domestic anaerobic digesters linked with sustainable sanitation in rural China

PubMed Central

DHINGRA, RADHIKA; CHRISTENSEN, ERICK R.; LIU, YANG; ZHONG, BO; WU, CHANG-FU; YOST, MICHAEL G.; REMAIS, JUSTIN V.

2013-01-01

Anaerobic digesters provide clean, renewable energy (biogas) by converting organic waste to methane, and are a key part of China's comprehensive rural energy plan. Here, experimental and modeling results are used to quantify the net greenhouse gas (GHG) reduction from substituting a household anaerobic digester for traditional energy sources in Sichuan, China. Tunable diode laser absorption spectroscopy and radial plume mapping were used to estimate the mass flux of fugitive methane emissions from active digesters. Using household energy budgets, the net improvement in GHG emissions associated with biogas installation was estimated using global warming commitment (GWC) as a consolidated measure of the warming effects of GHG emissions from cooking. In all scenarios biogas households had lower GWC than non-biogas households, by as much as 54%. Even biogas households with methane leakage exhibited lower GWC than non-biogas households, by as much as 48%. Based only on the averted GHG emissions over 10 years, the monetary value of a biogas installation was conservatively estimated at US$28.30 ($16.07 ton−1 CO2-eq.), which is available to partly offset construction costs. The interaction of biogas installation programs with policies supporting improved stoves, renewable harvesting of biomass, and energy interventions with substantial health co-benefits, are discussed. PMID:21348471

Greenhouse gas emission reductions from domestic anaerobic digesters linked with sustainable sanitation in rural China.

PubMed

Dhingra, Radhika; Christensen, Erick R; Liu, Yang; Zhong, Bo; Wu, Chang-Fu; Yost, Michael G; Remais, Justin V

2011-03-15

Anaerobic digesters provide clean, renewable energy (biogas) by converting organic waste to methane, and are a key part of China's comprehensive rural energy plan. Here, experimental and modeling results are used to quantify the net greenhouse gas (GHG) reduction from substituting a household anaerobic digester for traditional energy sources in Sichuan, China. Tunable diode laser absorption spectroscopy and radial plume mapping were used to estimate the mass flux of fugitive methane emissions from active digesters. Using household energy budgets, the net improvement in GHG emissions associated with biogas installation was estimated using global warming commitment (GWC) as a consolidated measure of the warming effects of GHG emissions from cooking. In all scenarios biogas households had lower GWC than nonbiogas households, by as much as 54%. Even biogas households with methane leakage exhibited lower GWC than nonbiogas households, by as much as 48%. Based only on the averted GHG emissions over 10 years, the monetary value of a biogas installation was conservatively estimated at US$28.30 ($16.07 ton(-1) CO(2)-eq), which is available to partly offset construction costs. The interaction of biogas installation programs with policies supporting improved stoves, renewable harvesting of biomass, and energy interventions with substantial health cobenefits are discussed.

The impact of uncertainty on optimal emission policies

NASA Astrophysics Data System (ADS)

Botta, Nicola; Jansson, Patrik; Ionescu, Cezar

2018-05-01

We apply a computational framework for specifying and solving sequential decision problems to study the impact of three kinds of uncertainties on optimal emission policies in a stylized sequential emission problem.We find that uncertainties about the implementability of decisions on emission reductions (or increases) have a greater impact on optimal policies than uncertainties about the availability of effective emission reduction technologies and uncertainties about the implications of trespassing critical cumulated emission thresholds. The results show that uncertainties about the implementability of decisions on emission reductions (or increases) call for more precautionary policies. In other words, delaying emission reductions to the point in time when effective technologies will become available is suboptimal when these uncertainties are accounted for rigorously. By contrast, uncertainties about the implications of exceeding critical cumulated emission thresholds tend to make early emission reductions less rewarding.

An overview of monitoring and reduction strategies for health and climate change related emissions in the Middle East and North Africa region

NASA Astrophysics Data System (ADS)

Abbass, Rana Alaa; Kumar, Prashant; El-Gendy, Ahmed

2018-02-01

This review assesses the current state of air pollution in the Middle East and North Africa (MENA) region. Emission types and sources in the region are identified and quantified to understand the monitoring, legislative and reduction needs through a systematic review of available literature. It is found that both health (e.g., particulate matter, PM; and heavy metals) and climate change (e.g., carbon dioxide and methane) emissions are increasing with the time. Regarding health emissions, over 99% of the MENA population is exposed to PM levels that exceed the standards set by the World Health Organization (WHO). The dominant source of climate change emissions is the energy sector contributing ∼38% of CO2 emissions, followed by the transport sector at ∼25%. Numerous studies have been carried out on air pollution in the region, however, there is a lack of comprehensive regional studies that would provide a holistic assessment. Most countries have air quality monitoring systems in place, however, the data is not effectively evaluated to devise pollution reduction strategies. Moreover, comprehensive emission inventories for the individual countries in the region are also lacking. The legislative and regulatory systems in MENA region follow the standards set by international environmental entities such as the WHO and the U.S. Environmental Protection Agency but their effective reinforcement remains a concern. It is concluded that the opportunities for emission reduction and control could be best implemented in the road transportation sector using innovative technologies. One of the potential ways forward is to channel finance flows from fossil fuel subsidies to upgrade road transport with public transportation systems such as buses and trains, as suggested by a 'high shift' scenario for MENA region. Furthermore, emission control programs and technologies are more effective when sponsored and implemented by the private sector; the success of Saudi Aramco in supporting

Exhaust emissions reduction from diesel engine using combined Annona-Eucalyptus oil blends and antioxidant additive

NASA Astrophysics Data System (ADS)

Senthil, R.; Silambarasan, R.; Pranesh, G.

2017-03-01

The limited resources, rising petroleum prices and depletion of fossil fuel have now become a matter of great concern. Hence, there is an urgent need for researchers to find some alternate fuels which are capable of substituting partly or wholly the higher demanded conventional diesel fuel. Lot of research work has been conducted on diesel engine using biodiesel and its blends with diesel as an alternate fuel. Very few works have been done with combination of biodiesel-Eucalypts oil without neat diesel and this leads to lots of scope in this area. The aim of the present study is to analyze the performance and emission characteristics of a single cylinder, direct injection, compression ignition engine using eucalyptus oil-biodiesel as fuel. The presence of eucalyptus oil in the blend reduces the viscosity and improves the volatility of the blends. The methyl ester of Annona oil is blended with eucalypts oil in 10, 20, 30, 40 and 50 %. The performance and emission characteristics are evaluated by operating the engine at different loads. The performance characteristics such as brake thermal efficiency, brake specific fuel consumption and exhaust gas temperature are evaluated. The emission constituents measured are Carbon monoxide (CO), unburned hydrocarbons (HC), Oxides of nitrogen (NOx) and Smoke. It is found that A50-Eu50 (50 Annona + 50 % Eucalyptus oil) blend showed better performance and reduction in exhaust emissions. But, it showed a very marginal increase in NOx emission when compared to that of diesel. Therefore, in order to reduce the NOx emission, antioxidant additive (A-tocopherol acetate) is mixed with Annona-Eucalyptus oil blends in various proportions by which NOx emission is reduced. Hence, A50-Eu50 blend can be used as an alternate fuel for diesel engine without any modifications.

China's Pathways to Achieving 40% ~ 45% Reduction in CO{sub 2} Emissions per Unit of GDP in 2020: Sectoral Outlook and Assessment of Savings Potential

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Nina; Fridley, David; Zhou, Nan

2011-09-30

Achieving China’s goal of reducing its carbon intensity (CO{sub 2} per unit of GDP) by 40% to 45% percent below 2005 levels by 2020 will require the strengthening and expansion of energy efficiency policies across the buildings, industries and transport sectors. This study uses a bottom-up, end-use model and two scenarios -- an enhanced energy efficiency (E3) scenario and an alternative maximum technically feasible energy efficiency improvement (Max Tech) scenario – to evaluate what policies and technical improvements are needed to achieve the 2020 carbon intensity reduction target. The findings from this study show that a determined approach by Chinamore » can lead to the achievement of its 2020 goal. In particular, with full success in deepening its energy efficiency policies and programs but following the same general approach used during the 11th Five Year Plan, it is possible to achieve 49% reduction in CO{sub 2} emissions per unit of GDP (CO{sub 2} emissions intensity) in 2020 from 2005 levels (E3 case). Under the more optimistic but feasible assumptions of development and penetration of advanced energy efficiency technology (Max Tech case), China could achieve a 56% reduction in CO{sub 2} emissions intensity in 2020 relative to 2005 with cumulative reduction of energy use by 2700 Mtce and of CO{sub 2} emissions of 8107 Mt CO{sub 2} between 2010 and 2020. Energy savings and CO{sub 2} mitigation potential varies by sector but most of the energy savings potential is found in energy-intensive industry. At the same time, electricity savings and the associated emissions reduction are magnified by increasing renewable generation and improving coal generation efficiency, underscoring the dual importance of end-use efficiency improvements and power sector decarbonization.« less

A Multimodel Assessment of the Influence of Regional Anthropogenic Emission Reductions on Aerosol Direct Radiative Forcing and the Role of Intercontinental Transport

NASA Technical Reports Server (NTRS)

Yu, Hongbin; Chin, Mian; West, Jason; Atherton, Cynthia S.; Bellouin, Nicolas; Bergmann, Dan; Bey, Isabelle; Bian, Huisheng; Diehl, Thomas; Forberth, Gerd;

Aircraft Piston Engine Exhaust Emission Symposium

NASA Technical Reports Server (NTRS)

1976-01-01

A 2-day symposium on the reduction of exhaust emissions from aircraft piston engines was held on September 14 and 15, 1976, at the Lewis Research Center in Cleveland, Ohio. Papers were presented by both government organizations and the general aviation industry on the status of government contracts, emission measurement problems, data reduction procedures, flight testing, and emission reduction techniques.

Waste Reduction Model

EPA Pesticide Factsheets

To help solid waste planners and organizations track/report GHG emissions reductions from various waste management practices. To assist in calculating GHG emissions of baseline and alternative waste management practices and provide the history of WARM.

Automated Boiler Combustion Controls for Emission Reduction and Efficiency Improvement

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

1998-12-02

In the late 1980s, then President Bush visited Krakow, Poland. The terrible air quality theremotivated him to initiate a USAID-funded program, managed by DOE, entitled "Krakow Clean Fossil Fuels and Energy Efficiency Program." The primary objective of this program was to encourage the formation of commercial ventures between U.S. and Polish firms to provide equipment and/or services to reduce pollution from low-emission sources in Krakow, Poland. This program led to the award of a number of cooperative agreements, including one to Control Techtronics International. The technical objective of CTI's cooperative agreement is to apply combustion controls to existing boiler plantsmore » in Krakow and transfer knowledge and technology through a joint U.S. and Polish commercial venture. CTI installed automatic combustion controls on five coal boilers for the district heating system in Krakow. Three of these were for domestic hot-water boilers, and two were for steam for industrial boilers. The following results have occurred due to the addition of CTI's combustion controls on these five existing boilers: ! 25% energy savings ! 85% reduction in particulate emissions The joint venture company CTI-Polska was then established. Eleven additional technical and costing proposals were initiated to upgrade other coal boilers in Krakow. To date, no co-financing has been made available on the Polish side. CTI-Polska continues in operation, serving customers in Russia and Ukraine. Should the market in Poland materialize, the joint venture company is established there to provide equipment and service.« less

Environmental effect of antioxidant additives on exhaust emission reduction in compression ignition engine fuelled with Annona methyl ester.

PubMed

Senthil, R; Silambarasan, R

2015-01-01

The aim of the present study is to analyse the effect of antioxidant l-ascorbic acid on engine performance and emissions of a diesel engine fuelled with methyl ester of Annona oil (MEAO). The antioxidant is mixed in various concentrations (100-400 mg) with MEAO. Result shows that the antioxidant additive mixture (MEAO+LA200) is effective in control of nitrogen oxides (NOx) and hydrocarbon (HC) emission of MEAO-fuelled engine without doing any engine modification. In this study by using MEAO, the NOx emission is reduced by about 23.38% at full load while compared with neat diesel fuel. Likewise there is a reduction in carbon monoxide, smoke, and HC by about 48%, 28.57% and 29.71% at full load condition compared with neat diesel fuel.

Evaluating the CO 2 emissions reduction potential and cost of power sector re-dispatch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steinberg, Daniel C.; Bielen, David A.; Townsend, Aaron

Prior studies of the U.S. electricity sector have recognized the potential to reduce carbon dioxide (CO2) emissions by substituting generation from coal-fired units with generation from under-utilized and lower-emitting natural gas-fired units; in fact, this type of 're-dispatch' was invoked as one of the three building blocks used to set the emissions targets under the Environmental Protection Agency's Clean Power Plan. Despite the existence of surplus natural gas capacity in the U.S., power system operational constraints not often considered in power sector policy analyses, such as transmission congestion, generator ramping constraints, minimum generation constraints, planned and unplanned generator outages, andmore » ancillary service requirements, could limit the potential and increase the cost of coal-to-gas re-dispatch. Using a highly detailed power system unit commitment and dispatch model, we estimate the maximum potential for re-dispatch in the Eastern Interconnection, which accounts for the majority of coal capacity and generation in the U.S. Under our reference assumptions, we find that maximizing coal-to-gas re-dispatch yields emissions reductions of 230 million metric tons (Mt), or 13% of power sector emissions in the Eastern Interconnection, with a corresponding average abatement cost of $15-$44 per metric ton of CO2, depending on the assumed supply elasticity of natural gas.« less

A HTAP Multi-Model Assessment of the Influence of Regional Anthropogenic Emission Reductions on Aerosol Direct Radiative Forcing and the Role of Intercontinental Transport

NASA Technical Reports Server (NTRS)

Yu, Hongbin; Chin, Mian; West, J. Jason; Atherton, Cynthia S.; Bellouin, Nicolas; Bergmann, Dan; Bey, Isabelle; Bian, Huisheng; Diehl, Thomas; Forberth, Gerd;

EMISSION REDUCTIONS AIMED AT IMPROVING AIR QUALITY: UNINTENDED CLIMATIC CONSEQUENCES AND THE EFFECT OF CLIMATE CHANGE ON THEIR SUCCESS

EPA Science Inventory

This work will provide improved understanding of the role of climate change, both in the recent past and future, on the success of pollutant control strategies, allowing for better planning and accountability of emission reductions. This work will also provide a quantitative a...

FUGITIVE EMISSION REDUCTIONS DUE TO THE USE OF ENCLOSED DOCTOR BLADE SYSTEMS IN THE FLEXOGRAPHIC AND ROTOGRAVURE PRINTING INDUSTRIES

EPA Science Inventory

The report gives results of a quantification of the level of fugitive emission reductions resulting from the use of enclosed doctor blade (EDB) systems in place of traditional ink feed systems at flexographic and rotogravure printing operations. An EDB system is an innovative ink...

Emission reduction from diesel engine using fumigation methanol and diesel oxidation catalyst.

PubMed

Zhang, Z H; Cheung, C S; Chan, T L; Yao, C D

2009-07-15

This study is aimed to investigate the combined application of fumigation methanol and a diesel oxidation catalyst for reducing emissions of an in-use diesel engine. Experiments were performed on a 4-cylinder naturally-aspirated direct-injection diesel engine operating at a constant speed of 1800 rev/min for five engine loads. The experimental results show that at low engine loads, the brake thermal efficiency decreases with increase in fumigation methanol; but at high loads, it slightly increases with increase in fumigation methanol. The fumigation method results in a significant increase in hydrocarbon (HC), carbon monoxide (CO), and nitrogen dioxide (NO(2)) emissions, but decrease in nitrogen oxides (NO(x)), smoke opacity and the particulate mass concentration. For the submicron particles, the total number of particles decreases. In all cases, there is little change in geometrical mean diameter of the particles. After catalytic conversion, the HC, CO, NO(2), particulate mass and particulate number concentrations were significantly reduced at medium to high engine loads; while the geometrical mean diameter of the particles becomes larger. Thus, the combined use of fumigation methanol and diesel oxidation catalyst leads to a reduction of HC, CO, NO(x), particulate mass and particulate number concentrations at medium to high engine loads.

Multispectral imaging of aircraft exhaust

NASA Astrophysics Data System (ADS)

Berkson, Emily E.; Messinger, David W.

2016-05-01

Aircraft pollutants emitted during the landing-takeoff (LTO) cycle have significant effects on the local air quality surrounding airports. There are currently no inexpensive, portable, and unobtrusive sensors to quantify the amount of pollutants emitted from aircraft engines throughout the LTO cycle or to monitor the spatial-temporal extent of the exhaust plume. We seek to thoroughly characterize the unburned hydrocarbon (UHC) emissions from jet engine plumes and to design a portable imaging system to remotely quantify the emitted UHCs and temporally track the distribution of the plume. This paper shows results from the radiometric modeling of a jet engine exhaust plume and describes a prototype long-wave infrared imaging system capable of meeting the above requirements. The plume was modeled with vegetation and sky backgrounds, and filters were selected to maximize the detectivity of the plume. Initial calculations yield a look-up chart, which relates the minimum amount of emitted UHCs required to detect the presence of a plume to the noise-equivalent radiance of a system. Future work will aim to deploy the prototype imaging system at the Greater Rochester International Airport to assess the applicability of the system on a national scale. This project will help monitor the local pollution surrounding airports and allow better-informed decision-making regarding emission caps and pollution bylaws.

Design and testing of an independently controlled urea SCR retrofit system for the reduction of NOx emissions from marine diesels.

PubMed

Johnson, Derek R; Bedick, Clinton R; Clark, Nigel N; McKain, David L

2009-05-15

Diesel engine emissions for on-road, stationary and marine applications are regulated in the United States via standards set by the Environmental Protection Agency (EPA). A major component of diesel exhaust that is difficult to reduce is nitrogen oxides (NOx). Selective catalytic reduction (SCR) has been in use for many years for stationary applications, including external combustion boilers, and is promising for NOx abatement as a retrofit for mobile applications where diesel compression ignition engines are used. The research presented in this paper is the first phase of a program focused on the reduction of NOx by use of a stand-alone urea injection system, applicable to marine diesel engines typical of work boats (e.g., tugs). Most current urea SCR systems communicate with engine controls to predict NOx emissions based on signals such as torque and engine speed, however many marine engines in use still employ mechanical injection technology and lack electronic communication abilities. The system developed and discussed in this paper controls NOx emissions independentof engine operating parameters and measures NOx and exhaust flow using the following exhaust sensor inputs: absolute pressure, differential pressure, temperature, and NOx concentration. These sensor inputs were integrated into an independent controller and open loop architecture to estimate the necessary amount of urea needed, and the controller uses pulse width modulation (PWM) to power an automotive fuel injector for airless urea delivery. The system was tested in a transient test cell on a 350 hp engine certified at 4 g/bhp-hr of NOx, with a goal of reducing the engine out NOx levels by 50%. NOx reduction capabilities of 41-67% were shown on the non road transient cycle (NRTC) and ICOMIA E5 steady state cycles with system optimization during testing to minimize the dilute ammonia slip to cycle averages of 5-7 ppm. The goal of 50% reduction of NOx can be achieved dependent upon cycle. Further

Reduction of Methane Emission during Slurry Storage by the Addition of Effective Microorganisms and Excessive Carbon Source from Brewing Sugar.

PubMed

Bastami, Mohd Saufi B; Jones, Davey L; Chadwick, David R

2016-11-01

Storing livestock manure is the primary stage of manure management where microbial processes and chemical reactions result in the release of methane (CH), nitrous oxide (NO), ammonia (NH), and carbon dioxide (CO). This study examined the reduction of CH emissions from slurry storage under two temperatures (cool [10°C] and warm [30°C]) when a glucose-rich substrate (brewing sugar) and activated effective microorganisms were applied at 10% (w/w) and 5% (v/w), respectively. Brewing sugar addition influenced microbial anaerobic respiration, resulting in a reduction of slurry pH to <5.0, through "self-acidification" caused by lactic acid production. Subsequently, CH emissions were significantly reduced by 87 and 99% in the cool and warm environments, respectively. The effective microorganism treatment did not change the chemical characteristics of the slurry but reduced CH emissions by 17 and 27% ( < 0.05) in the cool and warm environments, respectively. These results suggest that self-acidification after addition of a carbon source may be a promising alternative to slurry acidification using concentrated acids. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Impacts of emission reduction and meteorological conditions on air quality improvement during the 2014 Youth Olympic Games in Nanjing, China

NASA Astrophysics Data System (ADS)

Huang, Qian; Wang, Tijian; Chen, Pulong; Huang, Xiaoxian; Zhu, Jialei; Zhuang, Bingliang

2017-11-01

As the holding city of the 2nd Youth Olympic Games (YOG), Nanjing is highly industrialized and urbanized, and faces several air pollution issues. In order to ensure better air quality during the event, the local government took great efforts to control the emissions from pollutant sources. However, air quality can still be affected by synoptic weather, not only emission. In this paper, the influences of meteorological factors and emission reductions were investigated using observational data and numerical simulations with WRF-CMAQ (Weather Research and Forecasting - Community Multiscale Air Quality). During the month in which the YOG were held (August 2014), the observed hourly mean concentrations of SO2, NO2, PM10, PM2.5, CO and O3 were 11.6 µg m-3, 34.0 µg m-3, 57.8 µg m-3, 39.4 µg m-3, 0.9 mg m-3 and 38.8 µg m-3, respectively, which were below China National Ambient Air Quality Standard (level 2). However, model simulation showed that the weather conditions, such as weaker winds during the YOG, were adverse for better air quality and could increase SO2, NO2, PM10, PM2.5 and CO by 17.5, 16.9, 18.5, 18.8, 7.8 and 0.8 %. Taking account of local emission abatement only, the simulated SO2, NO2, PM10, PM2.5 and CO decreased by 24.6, 12.1, 15.1, 8.1 and 7.2 %. Consequently, stringent emission control measures can reduce the concentrations of air pollutants in the short term, and emission reduction is very important for air quality improvement during the YOG. A good example has been set for air quality protection for important social events.

Evaluation of costs associated with atmospheric mercury emission reductions from coal combustion in China in 2010 and projections for 2020.

PubMed

Zhang, Yue; Ye, Xuejie; Yang, Tianjun; Li, Jinling; Chen, Long; Zhang, Wei; Wang, Xuejun

2018-01-01

Coal combustion is the most significant anthropogenic mercury emission source in China. In 2013, China signed the Minamata Convention affirming that mercury emissions should be controlled more strictly. Therefore, an evaluation of the costs associated with atmospheric mercury emission reductions from China's coal combustion is essential. In this study, we estimated mercury abatement costs for coal combustion in China for 2010, based on a provincial technology-based mercury emission inventory. In addition, four scenarios were used to project abatement costs for 2020. Our results indicate that actual mercury emission related to coal combustion in 2010 was 300.8Mg, indicating a reduction amount of 174.7Mg. Under a policy-controlled scenario for 2020, approximately 49% of this mercury could be removed using air pollution control devices, making mercury emissions in 2020 equal to or lower than in 2010. The total abatement cost associated with mercury emissions in 2010 was 50.2×10 9 RMB. In contrast, the total abatement costs for 2020 under baseline versus policy-controlled scenarios, having high-energy and low-energy consumption, would be 32.0×10 9 versus 51.2×10 9 , and 27.4×10 9 versus 43.9×10 9 RMB, respectively. The main expense is associated with flue gas desulfurization. The unit abatement cost of mercury emissions in 2010 was 288×10 3 RMB/(kgHg). The unit abatement costs projected for 2020 under a baseline, a policy-controlled, and an United Nations Environmental Programme scenario would be 143×10 3 , 172×10 3 and 1066×10 3 RMB/(kgHg), respectively. These results are much lower than other international ones. However, the relative costs to China in terms of GPD are higher than in most developed countries. We calculated that abatement costs related to mercury emissions accounted for about 0.14% of the GDP of China in 2010, but would be between 0.03% and 0.06% in 2020. This decrease in abatement costs in terms of GDP suggests that various policy

Antioxidant (A-tocopherol acetate) effect on oxidation stability and NOx emission reduction in methyl ester of Annona oil operated diesel engine

NASA Astrophysics Data System (ADS)

Senthil, R.; Silambarasan, R.; Pranesh, G.

2017-05-01

There is a major drawback while using biodiesel as a alternate fuel for compression ignition diesel engine due to lower heating value, higher viscosity, higher density and higher oxides of nitrogen emission. To minimize these drawbacks, fuel additives can contribute towards engine performance and exhaust emission reduction either directly or indirectly. In this current work, the test was conducted to investigate the effect of antioxidant additive (A-tocopherol acetate) on oxidation stability and NOx emission in a of Annona methyl ester oil (MEAO) fueled diesel engine. The A-tocopherol acetate is mixed in different concentrations such as 0.01, 0.02, 0.03 and 0.04% with 100% by vol MEAO. It is concluded that the antioxidant additive very effective in increasing the oxidation stability and in controlling the NOx emission. Further, the addition of antioxidant additive is slight increase the HC, CO and smoke emissions. Hence, A-tocopherol acetate is very effective in controlling the NOx emission with MEAO operated diesel engine without any major modification.

Investigation of selective catalytic reduction impact on mercury speciation under simulated NOx emission control conditions.

PubMed

Lee, Chun W; Srivastava, Ravi K; Ghorishi, S Behrooz; Hastings, Thomas W; Stevens, Frank M

2004-12-01

Selective catalytic reduction (SCR) technology increasingly is being applied for controlling emissions of nitrogen oxides (NOx) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury (Hg) in coal combustion flue gases. The speciation of Hg is an important factor influencing the control and environmental fate of Hg emissions from coal combustion. The vanadium and titanium oxides, used commonly in the vanadia-titania SCR catalyst for catalytic NOx reduction, promote the formation of oxidized mercury (Hg2+). The work reported in this paper focuses on the impact of SCR on elemental mercury (Hg0) oxidation. Bench-scale experiments were conducted to investigate Hg0 oxidation in the presence of simulated coal combustion flue gases and under SCR reaction conditions. Flue gas mixtures with different concentrations of hydrogen chloride (HCl) and sulfur dioxide (SO2) for simulating the combustion of bituminous coals and subbituminous coals were tested in these experiments. The effects of HCl and SO2 in the flue gases on Hg0 oxidation under SCR reaction conditions were studied. It was observed that HCl is the most critical flue gas component that causes conversion of Hg0 to Hg2+ under SCR reaction conditions. The importance of HCl for Hg0 oxidation found in the present study provides the scientific basis for the apparent coal-type dependence observed for Hg0 oxidation occurring across the SCR reactors in the field.

Effects of emission reductions on organic aerosol in the southeastern United States

NASA Astrophysics Data System (ADS)

Blanchard, C. L.; Hidy, G. M.; Shaw, S.; Baumann, K.; Edgerton, E. S.

2016-01-01

Long-term (1999 to 2013) data from the Southeastern Aerosol Research and Characterization (SEARCH) network are used to show that anthropogenic emission reductions led to important decreases in fine-particle organic aerosol (OA) concentrations in the southeastern US On average, 45 % (range 25 to 63 %) of the 1999 to 2013 mean organic carbon (OC) concentrations are attributed to combustion processes, including fossil fuel use and biomass burning, through associations of measured OC with combustion products such as elemental carbon (EC), carbon monoxide (CO), and nitrogen oxides (NOx). The 2013 mean combustion-derived OC concentrations were 0.5 to 1.4 µg m-3 at the five sites operating in that year. Mean annual combustion-derived OC concentrations declined from 3.8 ± 0.2 µg m-3 (68 % of total OC) to 1.4 ± 0.1 µg m-3 (60 % of total OC) between 1999 and 2013 at the urban Atlanta, Georgia, site (JST) and from 2.9 ± 0.4 µg m-3 (39 % of total OC) to 0.7 ± 0.1 µg m-3 (30 % of total OC) between 2001 and 2013 at the urban Birmingham, Alabama (BHM), site. The urban OC declines coincide with reductions of motor vehicle emissions between 2006 and 2010, which may have decreased mean OC concentrations at the urban SEARCH sites by > 2 µg m-3. BHM additionally exhibits a decline in OC associated with SO2 from 0.4 ± 0.04 µg m-3 in 2001 to 0.2 ± 0.03 µg m-3 in 2013, interpreted as the result of reduced emissions from industrial sources within the city. Analyses using non-soil potassium as a biomass burning tracer indicate that biomass burning OC occurs throughout the year at all sites. All eight SEARCH sites show an association of OC with sulfate (SO4) ranging from 0.3 to 1.0 µg m-3 on average, representing ˜ 25 % of the 1999 to 2013 mean OC concentrations. Because the mass of OC identified with SO4 averages 20 to 30 % of the SO4 concentrations, the mean SO4-associated OC declined by ˜ 0.5 to 1 µg m-3 as SO4 concentrations decreased throughout the SEARCH region. The

Maximum Regional Emission Reduction Potential in Residential Sector Based on Spatial Distribution of Population and Resources

NASA Astrophysics Data System (ADS)

Winijkul, E.; Bond, T. C.

2011-12-01

In the residential sector, major activities that generate emissions are cooking and heating, and fuels ranging from traditional (wood) to modern (natural gas, or electricity) are used. Direct air pollutant emissions from this sector are low when natural gas or electricity are the dominant energy sources, as is the case in developed countries. However, in developing countries, people may rely on solid fuels and this sector can contribute a large fraction of emissions. The magnitude of the health loss associated with exposure to indoor smoke as well as its concentration among rural population in developing countries have recently put preventive measures high on the agenda of international development and public health organizations. This study focuses on these developing regions: Central America, Africa, and Asia. Current and future emissions from the residential sector depend on both fuel and cooking device (stove) type. Availability of fuels, stoves, and interventions depends strongly on spatial distribution. However, regional emission calculations do not consider this spatial dependence. Fuel consumption data is presented at country level, without information about where different types of fuel are used. Moreover, information about stove types that are currently used and can be used in the future is not available. In this study, we first spatially allocate current emissions within residential sector. We use Geographic Information System maps of temperature, electricity availability, forest area, and population to determine the distribution of fuel types and availability of stoves. Within each country, consumption of different fuel types, such as fuelwood, coal, and LPG is distributed among different area types (urban, peri-urban, and rural area). Then, the cleanest stove technologies which could be used in the area are selected based on the constraints of each area, i.e. availability of resources. Using this map, the maximum emission reduction compared with

Effects of Particle Filters and Selective Catalytic Reduction on In-Use Heavy-Duty Diesel Truck Emissions

NASA Astrophysics Data System (ADS)

Preble, C.; Cados, T.; Harley, R.; Kirchstetter, T.

2016-12-01

Heavy-duty diesel trucks (HDDT) are a major source of nitrogen oxides (NOx) and black carbon (BC) in urban environments, contributing to persistent ozone and particulate matter air quality problems. Diesel particle filters (DPFs) and selective catalytic reduction (SCR) systems that target PM and NOx emissions, respectively, have recently become standard equipment on new HDDT. DPFs can also be installed on older engines as a retrofit device. Previous work has shown that DPF and SCR systems can reduce NOx and BC emissions by up to 70% and 90%, respectively, compared to modern trucks without these after-treatment controls (Preble et al., ES&T 2015). DPFs can have the undesirable side-effect of increasing ultrafine particle (UFP) and nitrogen dioxide (NO2) emissions. While SCR systems can partially mitigate DPF-related NO2 increases, these systems can emit nitrous oxide (N2O), a potent greenhouse gas. We report new results from a study of HDDT emissions conducted in fall 2015 at the Port of Oakland and Caldecott Tunnel in California's San Francisco Bay Area. We report pollutant emission factors (g kg-1) for emitted NOx, NO2, BC, PM2.5, UFP, and N2O on a truck-by-truck basis. Using a roadside license plate recognition system, we categorize each truck by its engine model year and installed after-treatment controls. From this, we develop emissions profiles for trucks with and without DPF and SCR. We evaluate the effectiveness of these devices as a function of their age to determine whether degradation is an issue. We also compare the emission profiles of trucks traveling at low speeds along a level, arterial road en route to the port and at high speeds up a 4% grade highway approaching the tunnel. Given the climate impacts of BC and N2O, we also examine the global warming potential of emissions from trucks with and without DPF and SCR.

Energy efficiency and reduction of CO2 emissions from campsites management in a protected area.

PubMed

Del Moretto, Deny; Branca, Teresa Annunziata; Colla, Valentina

2018-09-15

Campsites can be a pollution source, mainly due to the energy consumption. In addition, the green areas, thanks to the direct CO 2 sequestration and the shading, indirectly prevent the CO 2 emissions related to energy consumption. The methodology presented in this paper allowed assessing the annual CO 2 emissions directly related to the campsite management and the consequent environmental impact in campsite clusters in Tuscany. The software i-Tree Canopy was exploited, enabling to evaluate in terms of "canopy" the tonnes of CO 2 sequestered by the vegetation within each campsite. Energy and water consumptions from 2012 to 2015 were assessed for each campsite. As far as the distribution of sequestered CO 2 is concerned, the campsites ranking was in accordance to their size. According to the indicator "T-Tree" or canopy cover, a larger area of the canopy cover allows using less outdoor areas covered by trees for the sequestration of the remaining amount of pollutants. The analysis shows that the considered campsites, that are located in a highly naturalistic Park, present significant positive aspects both in terms of CO 2 emission reductions and of energy efficiency. However, significant margins of improvement are also possible and they were analysed in the paper. Copyright © 2018 Elsevier Ltd. All rights reserved.

The contribution of waste management to the reduction of greenhouse gas emissions with applications in the city of Bucharest.

PubMed

Sandulescu, Elena

2004-12-01

Waste management is a key process to protect the environment and conserve resources. The contribution of appropriate waste management measures to the reduction of greenhouse gas (GHG) emissions from the city of Bucharest was studied. An analysis of the distribution of waste flows into various treatment options was conducted using the material flows and stocks analysis (MFSA). An optimum scenario (i.e. municipal solid waste stream managed as: recycling of recoverable materials, 8%; incineration of combustibles, 60%; landfilling of non-combustibles, 32%) was modelled to represent the future waste management in Bucharest with regard to its relevance towards the potential for GHG reduction. The results indicate that it can contribute by 5.5% to the reduction of the total amount of GHGs emitted from Bucharest.

Staggering reductions in atmospheric nitrogen dioxide across Canada in response to legislated transportation emissions reductions

NASA Astrophysics Data System (ADS)

Reid, Holly; Aherne, Julian

2016-12-01

It is well established that atmospheric nitrogen dioxide (NO2), associated mainly with emissions from transportation and industry, can have adverse effects on both human and ecosystem health. Specifically, atmospheric NO2 plays a role in the formation of ozone, and in acidic and nutrient deposition. As such, international agreements and national legislation, such as the On-Road Vehicle and Engine Emission Regulations (SOR/2003-2), and the Federal Agenda on Cleaner Vehicles, Engines and Fuel have been put into place to regulate and limit oxidized nitrogen emissions. The objective of this study was to assess the response of ambient air concentrations of NO2 across Canada to emissions regulations. Current NO2 levels across Canada were examined at 137 monitoring sites, and long-term annual and quarterly trends were evaluated for 63 continuous monitoring stations that had at least 10 years of data during the period 1988-2013. A non-parametric Mann-Kendall test (Z values) and Sen's slope estimate were used to determine monotonic trends; further changepoint analysis was used to determine periods with significant changes in NO2 air concentration and emissions time-series data. Current annual average NO2 levels in Canada range between 1.16 and 14.96 ppb, with the national average being 8.43 ppb. Provincially, average NO2 ranges between 3.77 and 9.25 ppb, with Ontario and British Columbia having the highest ambient levels of NO2. Long-term tend analysis indicated that the annual average NO2 air concentration decreased significantly at 87% of the stations (55 of 63), and decreased non-significantly at 10% (5 of 63) during the period 1998-2013. Concentrations increased (non-significantly) at only 3% (2 of 63) of the sites. Quarterly long-term trends showed similar results; significant decreases occurred at 84% (January-March), 88% (April-June), 83% (July-September), and 81% (October-December) of the sites. Declines in transportation emissions had the most influence on NO2 air

Climate effects of reducing black carbon emissions: Dependence on location of emission

NASA Astrophysics Data System (ADS)

Fuglestvedt, J.; Berntsen, T.; Myhre, G.; Rive, N. A.; Rypdal, K.; Gerland, S.; Pedersen, C.; Strøm, J.

2006-12-01

The role played by emissions of black carbon aerosols (BC) on the Earth's climate is diverse and the overall effect is still quite uncertain: Black carbon not only absorbs sunlight (direct effect), but it also has a semi- direct effect on clouds, and when deposited on snow and ice it changes the reflectivity (albedo) of the ground surface. These mechanisms generally have a warming effect on the climate. This poster presents a Norwegian project that focus on the net effect of current BC emissions and future possible reductions in emissions of BC aerosols, taking into account scientific, economic, and political perspectives on the inclusion of BC in climate policies. Thus, the scope of the project is interdisciplinary and includes observations in the Arctic, model simulations of dispersion of BC aerosols, its radiative forcing and climate effects. Some initial results from measurements of BC content in snow from the Norwegian Arctic and corresponding measurements for surface reflectance will be presented. The radiative forcing of BC emissions from different geographical regions differs due to differences in the removal processes (i.e. the lifetime) and the amount of solar radiation available for absorption (depends on latitude, clouds, and surface albedo). The atmospheric burdens and RF (of the direct effect) of regional BC emissions from fossil fuel sources have been calculated by the global chemical transport model Oslo-CTM2 and a radiative transfer model, and first results of time-integrated RF per unit of emission (equivalent to absolute GWPs) are presented. Future plans including i) analysis of cost effective emission reduction strategies, taking into account regional differences the forcing efficiencies, but also cost estimates for BC reductions in the different regions, and ii) an evaluation of the climate effects of the emission reductions through model simulations, including climatic, economic and political perspectives exploring obstacles and opportunities

Michigan`s air emission trading program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russette, T.M.; VanKolken, A.M.

1997-12-31

Michigan`s Emission Trading Program took effect on March 16, 1996 after two years of rule development by the Michigan Department of Environmental Quality, Air Quality Division and affected stakeholders. This program is based on the open market trading model and has been designed to (1) be consistent with existing federal and state rules and regulations, (2) integrate with existing air programs such as the permit program, and (3) address the needs of Michigan`s regulated community. Michigan`s Air Quality Division, along with other interested parties, initiated this program as part of market-based approaches to improve air quality through the reduction ofmore » criteria pollutants (except ozone) and volatile organic compounds. The Emission Trading rules offer potential benefits for Michigan companies that include increased operational flexibility, lower compliance costs, and/or money generated from the sale of the emission reduction credits. The environment also benefits from this program because the rules require that 10 percent of all registered emission reductions must be permanently retired as an air quality benefit. The emission trading program provides new opportunities for consulting firms to assist companies by identifying acceptable ways to generate and use emission reduction credits. Air pollution control companies may also see new opportunities by designing and installing control equipment in order to reduce air emissions. The role of consultants and equipment companies may expand to that of a broker selling and/or buying emission reduction credits on the Emission Trading Registry. Much has been learned since the conception of the air emission trading program. This paper will discuss how the program works in practice compared to what was envisioned in theory and the potential benefits from Michigan`s Emission Trading Program.« less

Stratospheric cruise emission reduction program

NASA Technical Reports Server (NTRS)

Diehl, L. A.; Reck, G. M.; Marek, C. J.; Szaniszlo, A. J.

1977-01-01

A recently implemented NASA effort specifically aimed at reducing cruise oxides of nitrogen from high-altitude aircraft is discussed. The desired emission levels and the combustor technology required to achieve them are discussed. A brief overview of the SCERP operating plan is given. Lean premixed-prevaporized combustion and some of the potential difficulties that are associated with applying this technique to gas turbine combustors are examined. Base technology was developed in several key areas. These fundamental studies are viewed as a requirement for successful implementation of the lean premixed combustion technique.

The evolution of shipping emissions and the costs of recent and forthcoming emission regulations in the northern European emission control area

NASA Astrophysics Data System (ADS)

Johansson, L.; Jalkanen, J.-P.; Kalli, J.; Kukkonen, J.

2013-06-01

An extensive inventory of marine exhaust emissions is presented in the northern European emission control area (ECA) in 2009 and 2011. The emissions of SOx, NOx, CO2, CO and PM2.5 were evaluated using the Ship Traffic Emission Assessment Model (STEAM). We have combined the information on individual vessel characteristics and position reports generated by the Automatic Identification System (AIS). The emission limitations from 2009 to 2011 have had a significant impact on reducing the emissions of both SOx and PM2.5. The predicted emissions of SOx originated from IMO-registered marine traffic have been reduced by 33%, from 322 ktons to 217 ktons, in the ECA from 2009 to 2011. The corresponding predicted reduction of PM2.5 emissions was 20%, from 74 ktons to 59 ktons. The highest CO2 and PM2.5 emissions in 2011 were located in the vicinity of the coast of the Netherlands, in the English Channel, near the South-Eastern UK and along the busiest shipping lines in the Danish Straits and the Baltic Sea. The changes of emissions and the financial costs caused by various regulative actions since 2005 were also evaluated, based on the increased direct fuel costs. We also simulated the effects and direct costs associated with the forthcoming switch to low-sulfur distillate fuels in 2015. According to the projections for the future, there will be a reduction of 85% in SOx emissions and a~reduction of 50% in PM2.5 emissions in 2015, compared with the corresponding shipping emissions in 2011 in the ECA. The corresponding relative increase in fuel costs for all shipping varied between 10% and 63%, depending on the development of the prices of fuels and the use of the sulfur scrubber equipment.

Research on PM2.5 emission reduction path of China ‘s electric power industry based on DEA model

NASA Astrophysics Data System (ADS)

Jin, Yanming; Yang, Fan; Liu, Jun

2018-02-01

Based on the theory of data envelopment analysis, this study constructs the environmental performance evaluation model of the power industry, analyzes the performance of development of clean energy, the implementation of electricity replacement, and the development of coal-fired energy-saving and emission-reducing measures. Put forward technology path to reduce emission in the future. The results show that (1) improving the proportion of coal for power generation, speeding up the replacement of electricity is the key to solve the haze in China. (2) With the photovoltaic and other new energy power generation costs gradually reduced and less limit from thermal energy, by final of “thirteenth five-years plan”, the economy of clean energy will surpass thermal energy-saving emission reduction. (3) After 2025, the economy of the electricity replacement will be able to show.

Impacts of global, regional, and sectoral black carbon emission reductions on surface air quality and human mortality

NASA Astrophysics Data System (ADS)

Anenberg, S. C.; Talgo, K.; Arunachalam, S.; Dolwick, P.; Jang, C.; West, J. J.

2011-07-01

As a component of fine particulate matter (PM2.5), black carbon (BC) is associated with premature human mortality. BC also affects climate by absorbing solar radiation and reducing planetary albedo. Several studies have examined the climate impacts of BC emissions, but the associated health impacts have been studied less extensively. Here, we examine the surface PM2.5 and premature mortality impacts of halving anthropogenic BC emissions globally and individually from eight world regions and three major economic sectors. We use a global chemical transport model, MOZART-4, to simulate PM2.5 concentrations and a health impact function to calculate premature cardiopulmonary and lung cancer deaths. We estimate that halving global anthropogenic BC emissions reduces outdoor population-weighted average PM2.5 by 542 ng m-3 (1.8 %) and avoids 157 000 (95 % confidence interval, 120 000-194 000) annual premature deaths globally, with the vast majority occurring within the source region. Most of these avoided deaths can be achieved by halving emissions in East Asia (China; 54 %), followed by South Asia (India; 31 %), however South Asian emissions have 50 % greater mortality impacts per unit BC emitted than East Asian emissions. Globally, halving residential, industrial, and transportation emissions contributes 47 %, 35 %, and 15 % to the avoided deaths from halving all anthropogenic BC emissions. These contributions are 1.2, 1.2, and 0.6 times each sector's portion of global BC emissions, owing to the degree of co-location with population globally. We find that reducing BC emissions increases regional SO4 concentrations by up to 28 % of the magnitude of the regional BC concentration reductions, due to reduced absorption of radiation that drives photochemistry. Impacts of residential BC emissions are likely underestimated since indoor PM2.5 exposure is excluded. We estimate ∼8 times more avoided deaths when BC and organic carbon (OC) emissions are halved together, suggesting

Greenhouse Gas and Ammonia Emissions from Different Stages of Liquid Manure Management Chains: Abatement Options and Emission Interactions.

PubMed

Mohankumar Sajeev, Erangu Purath; Winiwarter, Wilfried; Amon, Barbara

2018-01-01

Farm livestock manure is an important source of ammonia and greenhouse gases. Concerns over the environmental impact of emissions from manure management have resulted in research efforts focusing on emission abatement. However, questions regarding the successful abatement of manure-related emissions remain. This study uses a meta-analytical approach comprising 89 peer-reviewed studies to quantify emission reduction potentials of abatement options for liquid manure management chains from cattle and pigs. Analyses of emission reductions highlight the importance of accounting for interactions between emissions. Only three out of the eight abatement options considered (frequent removal of manure, anaerobic digesters, and manure acidification) reduced ammonia (3-60%), nitrous oxide (21-55%), and methane (29-74%) emissions simultaneously, whereas in all other cases, tradeoffs were identified. The results demonstrate that a shift from single-stage emission abatement options towards a whole-chain perspective is vital in reducing overall emissions along the manure management chain. The study also identifies some key elements like proper clustering, reporting of influencing factors, and explicitly describing assumptions associated with abatement options that can reduce variability in emission reduction estimates. Prioritization of abatement options according to their functioning can help to determine low-risk emission reduction options, specifically options that alter manure characteristics (e.g., reduced protein diets, anaerobic digestion, or slurry acidification). These insights supported by comprehensive emission measurement studies can help improve the effectiveness of emission abatement and harmonize strategies aimed at reducing air pollution and climate change simultaneously. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Reductions in emissions from deforestation from Indonesia’s moratorium on new oil palm, timber, and logging concessions

PubMed Central

Busch, Jonah; Ferretti-Gallon, Kalifi; Engelmann, Jens; Wright, Max; Austin, Kemen G.; Stolle, Fred; Turubanova, Svetlana; Potapov, Peter V.; Margono, Belinda; Hansen, Matthew C.; Baccini, Alessandro

2015-01-01

To reduce greenhouse gas emissions from deforestation, Indonesia instituted a nationwide moratorium on new license areas (“concessions”) for oil palm plantations, timber plantations, and logging activity on primary forests and peat lands after May 2011. Here we indirectly evaluate the effectiveness of this policy using annual nationwide data on deforestation, concession licenses, and potential agricultural revenue from the decade preceding the moratorium. We estimate that on average granting a concession for oil palm, timber, or logging in Indonesia increased site-level deforestation rates by 17–127%, 44–129%, or 3.1–11.1%, respectively, above what would have occurred otherwise. We further estimate that if Indonesia’s moratorium had been in place from 2000 to 2010, then nationwide emissions from deforestation over that decade would have been 241–615 MtCO2e (2.8–7.2%) lower without leakage, or 213–545 MtCO2e (2.5–6.4%) lower with leakage. As a benchmark, an equivalent reduction in emissions could have been achieved using a carbon price-based instrument at a carbon price of $3.30–7.50/tCO2e (mandatory) or $12.95–19.45/tCO2e (voluntary). For Indonesia to have achieved its target of reducing emissions by 26%, the geographic scope of the moratorium would have had to expand beyond new concessions (15.0% of emissions from deforestation and peat degradation) to also include existing concessions (21.1% of emissions) and address deforestation outside of concessions and protected areas (58.7% of emissions). Place-based policies, such as moratoria, may be best thought of as bridge strategies that can be implemented rapidly while the institutions necessary to enable carbon price-based instruments are developed. PMID:25605880

NOx emissions in China: historical trends and future perspectives

NASA Astrophysics Data System (ADS)

Zhao, B.; Wang, S. X.; Liu, H.; Xu, J. Y.; Fu, K.; Klimont, Z.; Hao, J. M.; He, K. B.; Cofala, J.; Amann, M.

2013-10-01

Nitrogen oxides (NOx) are key pollutants for the improvement of ambient air quality. Within this study we estimated the historical NOx emissions in China for the period 1995-2010, and calculated future NOx emissions every five years until 2030 under six emission scenarios. Driven by the fast growth of energy consumption, we estimate the NOx emissions in China increased rapidly from 11.0 Mt in 1995 to 26.1 Mt in 2010. Power plants, industry and transportation were major sources of NOx emissions, accounting for 28.4%, 34.0%, and 25.4% of the total NOx emissions in 2010, respectively. Two energy scenarios, a business as usual scenario (BAU) and an alternative policy scenario (PC), were developed to project future energy consumption. In 2030, total energy consumption is projected to increase by 64% and 27% from 2010 level respectively. Three sets of end-of-pipe pollution control measures, including baseline, progressive, and stringent control case, were developed for each energy scenario, thereby constituting six emission scenarios. By 2030, the total NOx emissions are projected to increase (compared to 2010) by 36% in the baseline while policy cases result in reduction up to 61% in the most ambitious case with stringent control measures. More than a third of the reduction achieved by 2030 between least and most ambitious scenario comes from power sector, and more than half is distributed equally between industry and transportation sectors. Selective catalytic reduction dominates the NOx emission reductions in power plants, while life style changes, control measures for industrial boilers and cement production are major contributors to reductions in industry. Timely enforcement of legislation on heavy-duty vehicles would contribute significantly to NOx emission reductions. About 30% of the NOx emission reduction in 2020 and 40% of the NOx emission reduction in 2030 could be treated as the ancillary benefit of energy conservation. Sensitivity analysis was conducted to

A Proposed Imaging System to Spatially and Temporally Monitor Unburned Hydrocarbons in Jet Engine Exhaust

NASA Astrophysics Data System (ADS)

Berkson, Emily E.

The local air quality surrounding airports is significantly impacted by ground-based airplane operations, such as landing, taxiing, idling, and takeoff. In recent years, studies performed across the country revealed that people living near major airports suffer from increased cancer risks and higher likelihoods of developing respiratory issues. Jet engine emissions have been monitored extensively by direct probing of the exhaust, but there are currently no inexpensive, portable, and unobtrusive methods with which to study exhaust plume dynamics. This study assesses the feasibility of designing a multispectral imaging system to track the spatial-temporal nature of a jet engine plume. Ideally, the imaging system will be both inexpensive and portable enough to be deployed at any airport. We begin by characterizing the phenomenology of jet engine emissions during ground operations and select unburned hydrocarbons (UHCs) as the basis for our plume tracking. A proposed LWIR imaging system layout and radiometric governing equation is developed to predict the camera's sensor-reaching radiance. We use two methods, the Ideal Gas Law and the Gaussian Plume Equation, to three-dimensionally model the UHC concentration within the plume, which, in turn, is used to predict the plume transmission as a function of downwind distance. Radiometric models are used to predict the sensor-reaching radiance of the camera, and two filter combinations are selected to maximize the plume detectability. Each filter combination uses one filter to monitor the background radiance and one filter to trace the plume radiance. They are located at 9.001/9.333 [mum] and 9.12/12.212 [mum]. The plume tracing filters are used to assess plume detectability, and we find that that a camera with an NEDeltaT of 0.05 [K] will be able to detect the plume up to 120 seconds after the engine has passed. We conclude by predicting what filter difference the camera will observe temporally, as plumes are continuously

Particulate matters emitted from maize straw burning for winter heating in rural areas in Guanzhong Plain, China: Current emission and future reduction

NASA Astrophysics Data System (ADS)

Sun, Jian; Shen, Zhenxing; Cao, Junji; Zhang, Leiming; Wu, Tingting; Zhang, Qian; Yin, Xiuli; Lei, Yali; Huang, Yu; Huang, R.-J.; Liu, Suixin; Han, Yongming; Xu, Hongmei; Zheng, Chunli; Liu, Pingping

2017-02-01

Maize straw smoldering in "Heated Kang" is the traditional way for heating in winter in rural areas of Guanzhong Plain. This smolder procedure produced large quantities of pollutants and got more and more concern from both public and researchers. In this study, on-site measurements of straw smoldering in a residence with a Chinese 'Heated Kang' (Scenario 1) were done to determine the emissions factors (EFs) for pollutants. Moreover, EFs of pollutants from an advanced stove fired with maize straw (Scenario 2) and maize-straw pellet (Scenario 3) had been conducted in a laboratory to find the new measure to reduce the pollution emissions. The results showed that the EFs of PM2.5 for three scenarios were 38.26 ± 13.94 g·kg- 1, 17.50 ± 8.29 g·kg- 1 and 2.95 ± 0.71 g·kg- 1, respectively. Comparing EFs of pollutants from 3 scenarios indicates that both briquetting of straw and advanced stove with air distribution system could efficiently reduce pollutants emission especially for Scenario 3. In detail, EFs of PM2.5, OC, EC and water soluble ions all have over 90% reduction between Scenarios 1 and 3. All particle-size distributions were unimodal, and all peaked in particle sizes < 0.47 μm. The EFs for K+ and Cl- were the highest of cations and anions for the majority of size groups. Converting to pellets and advanced stoves for residential heating could reduce PM2.5 emission from 48.3 Gg to 3.59 Gg, OC from 19.0 Gg to 0.91 Gg, EC from 1.7 Gg to 0.17 Gg and over 90% reduction on total water soluble ions in the whole region. A box model simulation for the Guanzhong Plain indicated that this conversion would lead to a 7.7% reduction in PM2.5 (from 130 to 120 μg·m- 3) in normal conditions and a 14.2% reduction (from 350 to 300 μg·m- 3) in hazy conditions. The results highlighted that the straw pellets burning in advanced stove can effectively reduce pollutants emitted and improve the energy use efficiency in comparison with maize straw smoldering in "Heated Kang

Locomotive Emission and Engine Idle Reduction Technology Demonstration Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

John R. Archer

2005-03-14

In response to a United States Department of Energy (DOE) solicitation, the Maryland Energy Administration (MEA), in partnership with CSX Transportation, Inc. (CSXT), submitted a proposal to DOE to support the demonstration of Auxiliary Power Unit (APU) technology on fifty-six CSXT locomotives. The project purpose was to demonstrate the idle fuel savings, the Nitrous Oxide (NOX) emissions reduction and the noise reduction capabilities of the APU. Fifty-six CSXT Baltimore Division locomotives were equipped with APUs, Engine Run Managers (ERM) and communications equipment to permit GPS tracking and data collection from the locomotives. Throughout the report there is mention of themore » percent time spent in the State of Maryland. The fifty-six locomotives spent most of their time inside the borders of Maryland and some spent all their time inside the state borders. Usually when a locomotive traveled beyond the Maryland State border it was into an adjoining state. They were divided into four groups according to assignment: (1) Power Unit/Switcher Mate units, (2) Remote Control units, (3) SD50 Pusher units and (4) Other units. The primary data of interest were idle data plus the status of the locomotive--stationary or moving. Also collected were main engine off, idling or working. Idle data were collected by county location, by locomotive status (stationary or moving) and type of idle (Idle 1, main engine idling, APU off; Idle 2, main engine off, APU on; Idle 3, main engine off, APU off; Idle 4, main engine idle, APU on). Desirable main engine idle states are main engine off and APU off or main engine off and APU on. Measuring the time the main engine spends in these desirable states versus the total time it could spend in an engine idling state allows the calculation of Percent Idle Management Effectiveness (%IME). IME is the result of the operation of the APU plus the implementation of CSXT's Warm Weather Shutdown Policy. It is difficult to separate the two. The

Willingness to engage in energy conservation and CO2 emissions reduction: An empirical investigation

NASA Astrophysics Data System (ADS)

Eluwa, S. E.; Siong, H. C.

2014-02-01

Africa's response to climate change has largely been focused on adaptation rather than mitigation. The reason for this is based on the fact that the continent contributes very little to global CO2 emission. Again, mitigation policies like carbon tax as being practised in developed countries may be costly and difficult to implement in a continent where most economies are fragile. Using behavioural change as an adaptation approach, we examined the opinion of Ibadan city residents towards energy conservation and CO2 emissions reduction. A total of 822 respondents were sampled across the three residential neighbourhoods of the city. Results from the study showed that female and male respondents differed in their opinion towards energy conservation. However, the female respondents tended to record higher mean scores on majority of the items used to capture energy conservation behaviour than their male counterparts. Also, those with higher level of education seemed to be more conscious of the environmental consequences arising from energy use at home than those with lower educational background. However, very slight variations were recorded in the mean value score across the different age groups, those respondents above 50 years scored a bit higher than other age groups.

Effects of emission reductions on organic aerosol in the southeastern United States

NASA Astrophysics Data System (ADS)

Blanchard, C. L.; Hidy, G. M.; Shaw, S.; Baumann, K.; Edgerton, E. S.

2015-06-01

Long-term (1999 to 2013) data from the Southeastern Aerosol Research and Characterization (SEARCH) network are used to characterize the effects of anthropogenic emission reductions on fine particle organic aerosol (OA) concentrations in the southeastern US. On average, 45 % (range 25 to 63 %) of the 1999 to 2013 mean organic carbon (OC) concentrations are attributed to combustion processes, including fossil-fuel use and biomass burning, through associations of measured OC with combustion products such as elemental carbon (EC), carbon monoxide (CO), and nitrogen oxides (NOx). The 2013 mean combustion-derived OC concentrations were 0.5 to 1.4 μg m-3 at the five sites operating in that year. Mean annual combustion-derived OC concentrations declined from 3.8 ± 0.2 μg m-3 (68 % of total OC) to 1.4 ± 0.1 μg m-3 (60 % of total OC) between 1999 and 2013 at the urban Atlanta, Georgia, site (JST) and from 2.9 ± 0.4 μg m-3 (39 % of total OC) to 0.7 ± 0.1 μg m-3 (30 % of total OC) between 2001 and 2013 at the urban Birmingham, Alabama, site (BHM). The urban OC declines coincide with reductions of motor-vehicle emissions between 2006 and 2010, which may have decreased mean OC concentrations at the urban SEARCH sites by > 2 μg m-3. BHM additionally exhibits a decline in OC associated with SO2 from 0.4 ± 0.04 μg m-3 in 2001 to 0.2 ± 0.03 μg m-3 in 2013, interpreted as the result of reduced emissions from industrial sources within the city. Analyses using non-soil potassium as a biomass-burning tracer indicate that biomass-burning OC occurs throughout the year at all sites. All eight SEARCH sites show an association of OC with sulfate (SO4) ranging from 0.3 to 1.0 μg m-3 on average, representing ~ 25 % of the 1999 to 2013 mean OC concentrations. Because the mass of OC associated with SO4 averages 20 to 30 % of the SO4 concentrations, the mean SO4-associated OC declined by ~ 0.5 to 1 μg m-3 as SO4 decreased throughout the SEARCH region. The 2013 mean SO4

A Cost Benefit Analysis of an Active Travel Intervention with Health and Carbon Emission Reduction Benefits.

PubMed

Chapman, Ralph; Keall, Michael; Howden-Chapman, Philippa; Grams, Mark; Witten, Karen; Randal, Edward; Woodward, Alistair

2018-05-11

Active travel (walking and cycling) is beneficial for people’s health and has many co-benefits, such as reducing motor vehicle congestion and pollution in urban areas. There have been few robust evaluations of active travel, and very few studies have valued health and emissions outcomes. The ACTIVE before-and-after quasi-experimental study estimated the net benefits of health and other outcomes from New Zealand’s Model Communities Programme using an empirical analysis comparing two intervention cities with two control cities. The Programme funded investment in cycle paths, other walking and cycling facilities, cycle parking, ‘shared spaces’, media campaigns and events, such as ‘Share the Road’, and cycle-skills training. Using the modified Integrated Transport and Health Impacts Model, the Programme’s net economic benefits were estimated from the changes in use of active travel modes. Annual benefits for health in the intervention cities were estimated at 34.4 disability-adjusted life years (DALYs) and two lives saved due to reductions in cardiac disease, diabetes, cancer, and respiratory disease. Reductions in transport-related carbon emissions were also estimated and valued. Using a discount rate of 3.5%, the estimated benefit/cost ratio was 11:1 and was robust to sensitivity testing. It is concluded that when concerted investment is made in active travel in a city, there is likely to be a measurable, positive return on investment.

A Cost Benefit Analysis of an Active Travel Intervention with Health and Carbon Emission Reduction Benefits

PubMed Central

Grams, Mark; Witten, Karen; Woodward, Alistair

2018-01-01

Active travel (walking and cycling) is beneficial for people’s health and has many co-benefits, such as reducing motor vehicle congestion and pollution in urban areas. There have been few robust evaluations of active travel, and very few studies have valued health and emissions outcomes. The ACTIVE before-and-after quasi-experimental study estimated the net benefits of health and other outcomes from New Zealand’s Model Communities Programme using an empirical analysis comparing two intervention cities with two control cities. The Programme funded investment in cycle paths, other walking and cycling facilities, cycle parking, ‘shared spaces’, media campaigns and events, such as ‘Share the Road’, and cycle-skills training. Using the modified Integrated Transport and Health Impacts Model, the Programme’s net economic benefits were estimated from the changes in use of active travel modes. Annual benefits for health in the intervention cities were estimated at 34.4 disability-adjusted life years (DALYs) and two lives saved due to reductions in cardiac disease, diabetes, cancer, and respiratory disease. Reductions in transport-related carbon emissions were also estimated and valued. Using a discount rate of 3.5%, the estimated benefit/cost ratio was 11:1 and was robust to sensitivity testing. It is concluded that when concerted investment is made in active travel in a city, there is likely to be a measurable, positive return on investment. PMID:29751618

Reduction in soil aggregation in response to dust emission processes

NASA Astrophysics Data System (ADS)

Swet, Nitzan; Katra, Itzhak

2016-09-01

Dust emission by aeolian (wind) soil erosion depends on the topsoil properties of the source area, especially on the nature of the aggregates where most dust particles are held. Although the key role of soil aggregates in dust emission, the response of soil aggregation to aeolian processes and its implications for dust emission remain unknown. This study focuses on aggregate size distribution (ASD) analyses before and after in-situ aeolian experiments in semiarid loess soils that are associated with dust emission. Wind tunnel simulations show that particulate matter (PM) emission and saltation rates depend on the initial ASD and shear velocity. Under all initial ASD conditions, the content of saltator-sized aggregates (63-250 μm) increased by 10-34% due to erosion of macro-aggregates (> 500 μm), resulting in a higher size ratio (SR) between the saltators and macro-aggregates following the aeolian erosion. The results revealed that the saltator production increases significantly for soils that are subjected to short-term (anthropogenic) disturbance of the topsoil. The findings highlight a decrease in soil aggregation for all initial ASD's in response to aeolian erosion, and consequently its influence on the dust emission potential. Changes in ASD should be considered as a key parameter in dust emission models of complex surfaces.

40 CFR 61.353 - Alternative means of emission limitation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for Benzene Waste Operations § 61.353 Alternative means of emission limitation. (a) If, in the Administrator's judgment, an alternative means of emission limitation will achieve a reduction in benzene emissions at least equivalent to the reduction in benzene emissions from the source achieved by the...

High Speed Link Radiated Emission Reduction

NASA Astrophysics Data System (ADS)

Bisognin, P.; Pelissou, P.; Cissou, R.; Giniaux, M.; Vargas, O.

2016-05-01

To control the radiated emission of high-speed link and associated unit, the current approach is to implement overall harness shielding on cables bundles. This method is very efficient in the HF/ VHF (high frequency/ very high frequency) and UHF (ultra-high frequency) ranges when the overall harness shielding is properly bonded on EMC back-shell. Unfortunately, with the increasing frequency, the associated half wavelength matches with the size of Sub-D connector that is the case for the L band. Therefore, the unit connectors become the main source of interference emission. For the L-band and S-band, the current technology of EMC back-shell leaves thin aperture matched with the L band half wavelength and therefore, the shielding effectiveness is drastically reduced. In addition, overall harness shielding means significant increases of the harness mass.Airbus D&S Toulouse and Elancourt investigated a new solution to avoid the need of overall harness shielding. The objective is to procure EM (Electro-Magnetic) clean unit connected to cables bundles free of any overall harness shielding. The proposed solution is to implement EMC common mode filtering on signal interfaces directly on unit PCB as close as possible the unit connector.Airbus D&S Elancourt designed and manufactured eight mock-ups of LVDS (Low Voltage Differential Signaling) interface PCBs' with different solutions of filtering. After verification of the signal integrity, three mock-ups were retained (RC filter and two common mode choke coil) in addition to the reference one (without EMC filter).Airbus D&S Toulouse manufactured associated LVDS cable bundles and integrated the RX (Receiver) and TX (Transmitter) LVDS boards in shielded boxes.Then Airbus D&S performed radiated emission measurement of the LVDS links subassemblies (e.g. RX and TX boxes linked by LVDS cables) according to the standard test method. This paper presents the different tested solutions and main conclusions on the feasibility of such

Feasibility of Applying Clean Development Mechanism and GHGs Emission Reductions in the Gold Mining Industry: A Case of Thailand

NASA Astrophysics Data System (ADS)

Kittipongvises, Suthirat

2015-12-01

There is presently overwhelming scientific consensus that global climate change is indeed occurring, and that human activities are the primary driver. An increasingly resource and carbon constrained world will continue to pose formidable challenges to major industries, including mining. Understanding the implications of climate change mitigation for the mining industry, however, remains limited. This paper presents the results of a feasibility study on the implementation of a clean development mechanism and greenhouse gases (GHGs) emission reductions in the gold mining industry. It draws upon and extends the analysis of a case study conducted on gold mining operations in Thailand. The results from the case study indicated that total GHGs emissions by company A were approximately 36,886 tons carbon dioxide equivalents (tCO2e) per annual gold production capacity that meet the eligibility criteria for small-scaled clean development mechanism (CDM) projects. The electrostatic separation process was found to release the lowest amount of GHGs, whereas comminution (i.e. crushing and grinding) generated the highest GHGs emissions. By scope, the emission from purchased electricity (scope 2) is the most significant source. Opportunities for CDM projects implementation in the gold mining sector can be found in employing energy efficiency measures. Through innovation, some technical efficiency and technological development in gold processing (i.e. high pressure grinding rolls (HPGR), vertical roller mills (VRM), gravity pre-concentration and microwave heating technologies) that have the potential to reduce energy use and also lower carbon footprint of the gold mining were further discussed. The evidence reviews found that HPGR and VRM abatement technologies have shown energy and climate benefits as electricity savings and CO2 reduction of about 8-25.93 kWh/ton ore processed and 1.8-26.66 kgCO2/ton ore processed, respectively. Implications for further research and practice were

Reduction of fine particle emissions from wood combustion with optimized condensing heat exchangers.

PubMed

Gröhn, Arto; Suonmaa, Valtteri; Auvinen, Ari; Lehtinen, Kari E J; Jokiniemi, Jorma

2009-08-15

In this study, we designed and built a condensing heat exchanger capable of simultaneous fine particle emission reduction and waste heat recovery. The deposition mechanisms inside the heat exchanger prototype were maximized using a computer model which was later compared to actual measurements. The main deposition mechanisms were diffusio- and thermophoresis which have previously been examined in similar conditions only separately. The obtained removal efficiency in the experiments was measured in the total number concentration and ranged between 26 and 40% for the given pellet stove and the heat exchanger. Size distributions and number concentrations were measured with a TSI Fast mobility particle sizer (FMPS). The computer model predicts that there exists a specific upper limit for thermo- and diffusiophoretic deposition for each temperature and water vapor concentration in the flue gas.

Is There a Future for Nuclear Power? Wind and Emission Reduction Targets in Fossil-Fuel Alberta

PubMed Central

Duan, Jun; Lynch, Rachel

2016-01-01

This paper explores the viability of relying on wind power to replace upwards of 60% of electricity generation in Alberta that would be lost if coal-fired generation is phased out. Using hourly wind data from 17 locations across Alberta, we are able to simulate the potential wind power output available to the Alberta grid when modern, 3.5 MW-capacity wind turbines are spread across the province. Using wind regimes for the years 2006 through 2015, we find that available wind power is less than 60% of installed capacity 98% of the time, and below 30% of capacity 74% of the time. There is only a small amount of correlation between wind speeds at different locations, but yet it remains necessary to rely on fossil fuel generation. Then, based on the results from a grid allocation model, we find that CO2 emissions can be reduced by about 30%, but only through a combination of investment in wind energy and reliance on purchases of hydropower from British Columbia. Only if nuclear energy is permitted into the generation mix would Alberta be able to meet its CO2-emissions reduction target in the electricity sector. With nuclear power, emissions can be reduced by upwards of 85%. PMID:27902712

Is There a Future for Nuclear Power? Wind and Emission Reduction Targets in Fossil-Fuel Alberta.

PubMed

van Kooten, G Cornelis; Duan, Jun; Lynch, Rachel

2016-01-01

This paper explores the viability of relying on wind power to replace upwards of 60% of electricity generation in Alberta that would be lost if coal-fired generation is phased out. Using hourly wind data from 17 locations across Alberta, we are able to simulate the potential wind power output available to the Alberta grid when modern, 3.5 MW-capacity wind turbines are spread across the province. Using wind regimes for the years 2006 through 2015, we find that available wind power is less than 60% of installed capacity 98% of the time, and below 30% of capacity 74% of the time. There is only a small amount of correlation between wind speeds at different locations, but yet it remains necessary to rely on fossil fuel generation. Then, based on the results from a grid allocation model, we find that CO2 emissions can be reduced by about 30%, but only through a combination of investment in wind energy and reliance on purchases of hydropower from British Columbia. Only if nuclear energy is permitted into the generation mix would Alberta be able to meet its CO2-emissions reduction target in the electricity sector. With nuclear power, emissions can be reduced by upwards of 85%.

Potential of solar domestic hot water systems in rural areas for greenhouse gas emission reduction in Poland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skowronski, P.; Wisniewski, G.

Application of solar energy for preparing domestic hot water is one of the easiest methods of utilization of this energy. At least part of the needs for warm tap water could be covered by solar systems. At present, mainly coal is used for water heating at dwellings in rural areas in Poland. Warm tap water consumption will increase significantly in the future as standards of living are improved. This can result in the growth of electricity use and an increase in primary fuel consumption. Present and future methods of warm sanitary water generation in rural areas in Poland is discussed,more » and associated greenhouse gas (GHG) emissions are estimated. It is predicted that the emission of CO{sub 2} and NOx will increase. The emission of CO and CH{sub 4} will decrease because of changes in the structure of the final energy carriers used. The economic and market potentials of solar energy for preparing warm water in rural areas are discussed. It is estimated that solar systems can meet 30%-45% of the energy demand for warm water generation in rural areas at a reasonable cost, with a corresponding CO{sub 2} emission reduction. The rate of realization of the economic potential of solar water heaters depends on subsidies for the installation of equipment. 13 refs., 9 tabs.« less

Costs of mitigating CO2 emissions from passenger aircraft

NASA Astrophysics Data System (ADS)

Schäfer, Andreas W.; Evans, Antony D.; Reynolds, Tom G.; Dray, Lynnette

2016-04-01

In response to strong growth in air transportation CO2 emissions, governments and industry began to explore and implement mitigation measures and targets in the early 2000s. However, in the absence of rigorous analyses assessing the costs for mitigating CO2 emissions, these policies could be economically wasteful. Here we identify the cost-effectiveness of CO2 emission reductions from narrow-body aircraft, the workhorse of passenger air transportation. We find that in the US, a combination of fuel burn reduction strategies could reduce the 2012 level of life cycle CO2 emissions per passenger kilometre by around 2% per year to mid-century. These intensity reductions would occur at zero marginal costs for oil prices between US$50-100 per barrel. Even larger reductions are possible, but could impose extra costs and require the adoption of biomass-based synthetic fuels. The extent to which these intensity reductions will translate into absolute emissions reductions will depend on fleet growth.

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction requirements...

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction requirements...

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction requirements...

OBSERVABLE INDICATORS OF THE SENSITIVITY OF PM2.5 NITRATE TO EMISSION REDUCTIONS PART I: DERIVATION OF THE ADJUSTED GAS RATIO AND APPLICABILITY AT REGULATORY-RELEVANT TIME SCALES

EPA Science Inventory

Chemical transport models have frequently been used to evaluate the impacts of emission reductions on inorganic PM2.5. However, such models are limited in their accuracy by uncertain estimates of the spatial and temporal characterization of emissions and meteorology. Site-speci...

Modeling carbon dioxide emissions reductions for three commercial reference buildings in Salt Lake City

NASA Astrophysics Data System (ADS)

Lucich, Stephen M.

In the United States, the buildings sector is responsible for approximately 40% of the national carbon dioxide (CO2) emissions. CO2 is created during the generation of heat and electricity, and has been linked to climate change, acid rain, a variety of health threats, surface water depletion, and the destruction of natural habitats. Building energy modeling is a powerful educational tool that building owners, architects, engineers, city planners, and policy makers can use to make informed decisions. The aim of this thesis is to simulate the reduction in CO2 emissions that may be achieved for three commercial buildings located in Salt Lake City, UT. The following two questions were used to guide this process: 1. How much can a building's annual CO2 emissions be reduced through a specific energy efficiency upgrade or policy? 2. How much can a building's annual CO2 emissions be reduced through the addition of a photovoltaic (PV) array? How large should the array be? Building energy simulations were performed with the Department of Energy's EnergyPlus software, commercial reference building models, and TMY3 weather data. The chosen models were a medium office building, a primary school, and a supermarket. Baseline energy consumption data were simulated for each model in order to identify changes that would have a meaningful impact. Modifications to the buildings construction and operation were considered before a PV array was incorporated. These modifications include (1) an improved building envelope, (2) reduced lighting intensity, and (3) modified HVAC temperature set points. The PV array sizing was optimized using a demand matching approach based on the method of least squares. The arrays tilt angle was optimized using the golden section search algorithm. Combined, energy efficiency upgrades and the PV array reduced building CO2 emissions by 58.6, 54.0, and 52.2% for the medium office, primary school, and supermarket, respectively. However, for these models, it was

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... subject to section 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction...

Predator-induced reduction of freshwater carbon dioxide emissions

NASA Astrophysics Data System (ADS)

Atwood, Trisha B.; Hammill, Edd; Greig, Hamish S.; Kratina, Pavel; Shurin, Jonathan B.; Srivastava, Diane S.; Richardson, John S.

2013-03-01

Predators can influence the exchange of carbon dioxide between ecosystems and the atmosphere by altering ecosystem processes such as decomposition and primary production, according to food web theory. Empirical knowledge of such an effect in freshwater systems is limited, but it has been suggested that predators in odd-numbered food chains suppress freshwater carbon dioxide emissions, and predators in even-numbered food chains enhance emissions. Here, we report experiments in three-tier food chains in experimental ponds, streams and bromeliads in Canada and Costa Rica in the presence or absence of fish (Gasterosteus aculeatus) and invertebrate (Hesperoperla pacifica and Mecistogaster modesta) predators. We monitored carbon dioxide fluxes along with prey and primary producer biomass. We found substantially reduced carbon dioxide emissions in the presence of predators in all systems, despite differences in predator type, hydrology, climatic region, ecological zone and level of in situ primary production. We also observed lower amounts of prey biomass and higher amounts of algal and detrital biomass in the presence of predators. We conclude that predators have the potential to markedly influence carbon dioxide dynamics in freshwater systems.

How to reach haze control targets by air pollutants emission reduction in the Beijing-Tianjin-Hebei region of China?

PubMed

Xu, Feng; Xiang, Nan; Higano, Yoshiro

2017-01-01

Currently, Haze is one of the greatest environmental problems with serious impacts on human health in China, especially in capital region (Beijing-Tianjin-Hebei region). To alleviate this problem, the Chinese government introduced a National Air Pollution Control Action Plan (NAPCAP) with air pollutants reduction targets by 2017. However, there is doubt whether these targets can be achieved once the plan is implemented. In this work, the effectiveness of NAPCAP is analyzed by developing models of the statistical relationship between PM2.5 concentrations and air pollutant emissions (SO2, NOx, smoke and dust), while taking into account wind and neighboring transfer impacts. The model can also identify ways of calculating the intended emission levels in the Beijing-Tianjin-Hebei area. The results indicate that haze concentration control targets will not be attained by following the NAPCAP, and that the amount of progress needed to meet the targets is unrealistic. A more appropriate approach to reducing air emissions is proposed, which addresses joint regional efforts.

Atmospheric impacts of black carbon emission reductions through the strategic use of biodiesel in California.

PubMed

Zhang, Hongliang; Magara-Gomez, Kento T; Olson, Michael R; Okuda, Tomoaki; Walz, Kenneth A; Schauer, James J; Kleeman, Michael J

2015-12-15

The use of biodiesel as a replacement for petroleum-based diesel fuel has gained interest as a strategy for greenhouse gas emission reductions, energy security, and economic advantage. Biodiesel adoption may also reduce particulate elemental carbon (EC) emissions from conventional diesel engines that are not equipped with after-treatment devices. This study examines the impact of biodiesel blends on EC emissions from a commercial off-road diesel engine and simulates the potential public health benefits and climate benefits. EC emissions from the commercial off-road engine decreased by 76% when ultra-low sulfur commercial diesel (ULSD) fuel was replaced by biodiesel. Model calculations predict that reduced EC emissions translate directly into reduced EC concentrations in the atmosphere, but the concentration of secondary particulate matter was not directly affected by this fuel change. Redistribution of secondary particulate matter components to particles emitted from other sources did change the size distribution and therefore deposition rates of those components. Modification of meteorological variables such as water content and temperature influenced secondary particulate matter formation. Simulations with a source-oriented WRF/Chem model (SOWC) for a severe air pollution episode in California that adopted 75% biodiesel blended with ULSD in all non-road diesel engines reduced surface EC concentrations by up to 50% but changed nitrate and total PM2.5 mass concentrations by less than ±5%. These changes in concentrations will have public health benefits but did not significantly affect radiative forcing at the top of the atmosphere. The removal of EC due to the adoption of biodiesel produced larger coatings of secondary particulate matter on other atmospheric particles containing residual EC leading to enhanced absorption associated with those particles. The net effect was a minor change in atmospheric optical properties despite a large change in atmospheric EC

Jet aircraft emissions during cruise: Present and future

NASA Technical Reports Server (NTRS)

Grobman, J. S.

1975-01-01

Forecasts of engine exhaust emissions that may be practicably achievable for future commercial aircraft operating at high altitude cruise conditions are compared to cruise emission for present day aircraft. The forecasts are based on: (1) knowledge of emission characteristics of combustors and augmentors; (2) combustion research in emission reduction technology, and (3) trends in projected engine designs for advanced subsonic or supersonic commercial aircraft. Recent progress that was made in the evolution of emissions reduction technology is discussed.

The influence of biopreparations on the reduction of energy consumption and CO2 emissions in shallow and deep soil tillage.

PubMed

Naujokienė, Vilma; Šarauskis, Egidijus; Lekavičienė, Kristina; Adamavičienė, Aida; Buragienė, Sidona; Kriaučiūnienė, Zita

2018-06-01

The application of innovation in agriculture technologies is very important for increasing the efficiency of agricultural production, ensuring the high productivity of plants, production quality, farm profitability, the positive balance of used energy, and the requirements of environmental protection. Therefore, it is a scientific problem that solid and soil surfaces covered with plant residue have a negative impact on the work, traction resistance, energy consumption, and environmental pollution of tillage machines. The objective of this work was to determine the dependence of the reduction of energy consumption and CO 2 gas emissions on different biopreparations. Experimental research was carried out in a control (SC1) and seven different biopreparations using scenarios (SC2-SC8) using bacterial and non-bacterial biopreparations in different consistencies (with essential and mineral oils, extracts of various grasses and sea algae, phosphorus, potassium, humic and gibberellic acids, copper, zinc, manganese, iron, and calcium), estimating discing and plowing as the energy consumption parameters of shallow and deep soil tillage machines, respectively. CO 2 emissions were determined by evaluating soil characteristics (such as hardness, total porosity and density). Meteorological conditions such average daily temperatures (2015-20.3 °C; 2016-16.90 °C) and precipitations (2015-6.9 mm; 2016-114.9 mm) during the month strongly influenced different results in 2015 and 2016. Substantial differences between the averages of energy consumption identified in approximately 62% of biological preparation combinations created usage scenarios. Experimental research established that crop field treatments with biological preparations at the beginning of vegetation could reduce the energy consumption of shallow tillage machines by up to approximately 23%, whereas the energy consumption of deep tillage could be reduced by up to approximately 19.2% compared with the control

Prioritizing environmental justice and equality: diesel emissions in southern California.

PubMed

Marshall, Julian D; Swor, Kathryn R; Nguyen, Nam P

2014-04-01

Existing environmental policies aim to reduce emissions but lack standards for addressing environmental justice. Environmental justice research documents disparities in exposure to air pollution; however, little guidance currently exists on how to make improvements or on how specific emission-reduction scenarios would improve or deteriorate environmental justice conditions. Here, we quantify how emission reductions from specific sources would change various measures of environmental equality and justice. We evaluate potential emission reductions for fine diesel particulate matter (DPM) in Southern California for five sources: on-road mobile, off-road mobile, ships, trains, and stationary. Our approach employs state-of-the-science dispersion and exposure models. We compare four environmental goals: impact, efficiency, equality, and justice. Results indicate potential trade-offs among those goals. For example, reductions in train emissions produce the greatest improvements in terms of efficiency, equality, and justice, whereas off-road mobile source reductions can have the greatest total impact. Reductions in on-road emissions produce improvements in impact, equality, and justice, whereas emission reductions from ships would widen existing population inequalities. Results are similar for complex versus simplified exposure analyses. The approach employed here could usefully be applied elsewhere to evaluate opportunities for improving environmental equality and justice in other locations.

Prospects for energy efficiency improvement and reduction of emissions and life cycle costs for natural gas vehicles

NASA Astrophysics Data System (ADS)

Kozlov, A. V.; Terenchenko, A. S.; Luksho, V. A.; Karpukhin, K. E.

2017-01-01

This work is devoted to the experimental investigation of the possibilities to reduce greenhouse gas emissions and to increase energy efficiency of engines that use natural gas as the main fuel and the analysis of economic efficiency of use of dual fuel engines in vehicles compared to conventional diesel. The results of experimental investigation of a 190 kW dual-fuel engine are presented; it is shown that quantitative and qualitative working process control may ensure thermal efficiency at the same level as that of the diesel engine and in certain conditions 5...8% higher. The prospects for reduction of greenhouse gas emissions have been assessed. The technical and economic evaluation of use of dual fuel engines in heavy-duty vehicles has been performed, taking into account the total life cycle. It is shown that it is possible to reduce life cycle costs by two times.

Energy savings, emission reductions, and health co-benefits of the green building movement.

PubMed

P, MacNaughton; X, Cao; J, Buonocore; J, Cedeno-Laurent; J, Spengler; A, Bernstein; J, Allen

2018-06-01

Buildings consume nearly 40% of primary energy production globally. Certified green buildings substantially reduce energy consumption on a per square foot basis and they also focus on indoor environmental quality. However, the co-benefits to health through reductions in energy and concomitant reductions in air pollution have not been examined.We calculated year by year LEED (Leadership in Energy and Environmental Design) certification rates in six countries (the United States, China, India, Brazil, Germany, and Turkey) and then used data from the Green Building Information Gateway (GBIG) to estimate energy savings in each country each year. Of the green building rating schemes, LEED accounts for 32% of green-certified floor space and publically reports energy efficiency data. We employed Harvard's Co-BE Calculator to determine pollutant emissions reductions by country accounting for transient energy mixes and baseline energy use intensities. Co-BE applies the social cost of carbon and the social cost of atmospheric release to translate these reductions into health benefits. Based on modeled energy use, LEED-certified buildings saved $7.5B in energy costs and averted 33MT of CO 2 , 51 kt of SO 2 , 38 kt of NO x , and 10 kt of PM 2.5 from entering the atmosphere, which amounts to $5.8B (lower limit = $2.3B, upper limit = $9.1B) in climate and health co-benefits from 2000 to 2016 in the six countries investigated. The U.S. health benefits derive from avoiding an estimated 172-405 premature deaths, 171 hospital admissions, 11,000 asthma exacerbations, 54,000 respiratory symptoms, 21,000 lost days of work, and 16,000 lost days of school. Because the climate and health benefits are nearly equivalent to the energy savings for green buildings in the United States, and up to 10 times higher in developing countries, they provide an important and previously unquantified societal value. Future analyses should consider these co-benefits when weighing policy

40 CFR 76.11 - Emissions averaging.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.11 Emissions averaging. (a) General... compliance with the Acid Rain emission limitation for NOX under the plan only if the following requirements...

40 CFR 76.11 - Emissions averaging.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.11 Emissions averaging. (a) General... compliance with the Acid Rain emission limitation for NOX under the plan only if the following requirements...

40 CFR 76.11 - Emissions averaging.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.11 Emissions averaging. (a) General... compliance with the Acid Rain emission limitation for NOX under the plan only if the following requirements...

Medicalization of global health 4: The universal health coverage campaign and the medicalization of global health.

PubMed

Clark, Jocalyn

2014-01-01

Universal health coverage (UHC) has emerged as the leading and recommended overarching health goal on the post-2015 development agenda, and is promoted with fervour. UHC has the backing of major medical and health institutions, and is designed to provide patients with universal access to needed health services without financial hardship, but is also projected to have 'a transformative effect on poverty, hunger, and disease'. Multiple reports and resolutions support UHC and few offer critical analyses; but among these are concerns with imprecise definitions and the ability to implement UHC at the country level. A medicalization lens enriches these early critiques and identifies concerns that the UHC campaign contributes to the medicalization of global health. UHC conflates health with health care, thus assigning undue importance to (biomedical) health services and downgrading the social and structural determinants of health. There is poor evidence that UHC or health care alone improves population health outcomes, and in fact health care may worsen inequities. UHC is reductionistic because it focuses on preventative and curative actions delivered at the individual level, and ignores the social and political determinants of health and right to health that have been supported by decades of international work and commitments. UHC risks commodifying health care, which threatens the underlying principles of UHC of equity in access and of health care as a collective good.

Greenhouse gas and air pollutant emission reduction potentials of renewable energy--case studies on photovoltaic and wind power introduction considering interactions among technologies in Taiwan.

PubMed

Kuo, Yu-Ming; Fukushima, Yasuhiro

2009-03-01

To achieve higher energy security and lower emission of greenhouse gases (GHGs) and pollutants, the development of renewable energy has attracted much attention in Taiwan. In addition to its contribution to the enhancement of reliable indigenous resources, the introduction of renewable energy such as photovoltaic (PV) and wind power systems reduces the emission of GHGs and air pollutants by substituting a part of the carbon- and pollutant-intensive power with power generated by methods that are cleaner and less carbon-intensive. To evaluate the reduction potentials, consequential changes in the operation of different types of existing power plants have to be taken into account. In this study, a linear mathematical programming model is constructed to simulate a power mix for a given power demand in a power market sharing a cost-minimization objective. By applying the model, the emission reduction potentials of capacity extension case studies, including the enhancement of PV and wind power introduction at different scales, were assessed. In particular, the consequences of power mix changes in carbon dioxide, nitrogen oxides, sulfur oxides, and particulates were discussed. Seasonally varying power demand levels, solar irradiation, and wind strength were taken into account. In this study, we have found that the synergetic reduction of carbon dioxide emission induced by PV and wind power introduction occurs under a certain level of additional installed capacity. Investigation of a greater variety of case studies on scenario development with emerging power sources becomes possible by applying the model developed in this study.

Greenhouse gas and air pollutant emission reduction potentials of renewable energy - case studies on photovoltaic and wind power introduction considering interactions among technologies in Taiwan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu-Ming Kuo; Yasuhiro Fukushima

2009-03-15

To achieve higher energy security and lower emission of greenhouse gases (GHGs) and pollutants, the development of renewable energy has attracted much attention in Taiwan. In addition to its contribution to the enhancement of reliable indigenous resources, the introduction of renewable energy such as photovoltaic (PV) and wind power systems reduces the emission of GHGs and air pollutants by substituting a part of the carbon- and pollutant-intensive power with power generated by methods that are cleaner and less carbon-intensive. To evaluate the reduction potentials, consequential changes in the operation of different types of existing power plants have to be takenmore » into account. In this study, a linear mathematical programming model is constructed to simulate a power mix for a given power demand in a power market sharing a cost-minimization objective. By applying the model, the emission reduction potentials of capacity extension case studies, including the enhancement of PV and wind power introduction at different scales, were assessed. In particular, the consequences of power mix changes in carbon dioxide, nitrogen oxides, sulfur oxides, and particulates were discussed. Seasonally varying power demand levels, solar irradiation, and wind strength were taken into account. In this study, we have found that the synergetic reduction of carbon dioxide emission induced by PV and wind power introduction occurs under a certain level of additional installed capacity. Investigation of a greater variety of case studies on scenario development with emerging power sources becomes possible by applying the model developed in this study. 15 refs., 8 figs., 11 tabs.« less

Reduction of zinc emissions from buildings; the policy of Amsterdam.

PubMed

Gouman, E

2004-01-01

In Amsterdam zinc coming from the roofs and gutters of the buildings accounts for about 50% of the zinc emissions into the surface water (i.e. canals and rivers). This causes water and sediment pollution. Dumping strongly polluted sediment costs ten times more then dumping less polluted mud. Therefore the City of Amsterdam has developed a policy for reducing the zinc emissions from buildings based on the current environmental legislation and the current national targets for surface water quality. Zinc roofs on new and renovated buildings are not permitted. Run off water from zinc roofs of existing buildings is allowed to contain a maximum of 200 microg/l zinc. For the zinc gutters of houses, Amsterdam will promote measures to reduce zinc emissions. To investigate the feasibility of measures, research has been carried out on the zinc emissions of gutters and the effect of covering gutters with an impermeable foil. This research shows clearly that covering zinc gutters with EPDM foil reduces the zinc emissions by 90% from 8.5 to 0.88 gram per square metre per year including the atmospheric deposition.

Experimental study of the effect of cycle pressure on lean combustion emissions

NASA Technical Reports Server (NTRS)

Roffe, G.; Venkataramani, K. S.

1978-01-01

Experiments were conducted in which a stream of premixed propane and air was burned under conditions representative of gas turbine operation. Emissions of NOx, CO, and unburned hydrocarbons (UHC) were measured over a range of combustor inlet temperature, pressure, and residence time at equivalence ratios from 0.7 down to the lean stability limit. At an inlet temperature of 600 K, observed NOx levels dropped markedly with decreasing pressure for pressures below 20 atm. The NOx levels are proportional to combustor residence time and formation rates were principally a function of adiabatic flame temperature. For adiabatic flame temperatures of 2050 K and higher, CO reached chemical equilibrium within 2 msec. Unburned hydrocarbon species dropped to a negligible level within 2 msec regardless of inlet temperature, pressure, or equivalence ratio. For a combustor residence time of 2.5 msec, combustion inefficiency became less than 0.01% at an adiabatic flame temperature of 2050 K. The maximum combustion inefficiency observed was on the order of 1% and corresponded to conditions near the lean stability limit. Using a perforated plate flameholder, this limit is well represented by the condition of 1800 K adiabatic flame temperature.

Exhaust emission reduction for intermittent combustion aircraft engines

NASA Technical Reports Server (NTRS)

Moffett, R. N.

1979-01-01

Three concepts for optimizing the performance, increasing the fuel economy, and reducing exhaust emission of the piston aircraft engine were investigated. High energy-multiple spark discharge and spark plug tip penetration, ultrasonic fuel vaporization, and variable valve timing were evaluated individually. Ultrasonic fuel vaporization did not demonstrate sufficient improvement in distribution to offset the performance loss caused by the additional manifold restriction. High energy ignition and revised spark plug tip location provided no change in performance or emissions. Variable valve timing provided some performance benefit; however, even greater performance improvement was obtained through induction system tuning which could be accomplished with far less complexity.

40 CFR 76.11 - Emissions averaging.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.11 Emissions averaging. (a) General... averaging plan is in compliance with the Acid Rain emission limitation for NOX under the plan only if the...

40 CFR 76.11 - Emissions averaging.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.11 Emissions averaging. (a) General... averaging plan is in compliance with the Acid Rain emission limitation for NOX under the plan only if the...

Pricing, Carbon Emission Reduction, Low-Carbon Promotion and Returning Decision in a Closed-Loop Supply Chain under Vertical and Horizontal Cooperation.

PubMed

Li, Hui; Wang, Chuanxu; Shang, Meng; Ou, Wei

2017-11-01

In this paper, we examine the influences of vertical and horizontal cooperation models on the optimal decisions and performance of a low-carbon closed-loop supply chain (CLSC) with a manufacturer and two retailers, and study optimal operation in the competitive pricing, competitive the low-carbon promotion, the carbon emission reduction, the used-products collection and the profits. We consider the completely decentralized model, M-R vertical cooperation model, R-R horizontal cooperation model, M-R-R vertical and horizontal cooperation model and completely centralized model, and also identify the optimal decision results and profits. It can be observed from a systematic comparison and numerical analysis that the completely centralized model is best in all optimal decision results among all models. In semi-cooperation, the M-R vertical cooperation model is positive, the R-R horizontal cooperation model is passive, and the positivity of the M-R-R vertical and horizontal cooperation model decreases with competitive intensity increasing in the used-products returning, carbon emissions reduction level, low-carbon promotion effort and the profits of the manufacturer and the entire supply chain.

Effect of advanced aftertreatment for PM and NOx reduction on heavy-duty diesel engine ultrafine particle emissions.

PubMed

Herner, Jorn Dinh; Hu, Shaohua; Robertson, William H; Huai, Tao; Chang, M-C Oliver; Rieger, Paul; Ayala, Alberto

2011-03-15

Four heavy-duty and medium-duty diesel vehicles were tested in six different aftertreament configurations using a chassis dynamometer to characterize the occurrence of nucleation (the conversion of exhaust gases to particles upon dilution). The aftertreatment included four different diesel particulate filters and two selective catalytic reduction (SCR) devices. All DPFs reduced the emissions of solid particles by several orders of magnitude, but in certain cases the occurrence of a volatile nucleation mode could increase total particle number emissions. The occurrence of a nucleation mode could be predicted based on the level of catalyst in the aftertreatment, the prevailing temperature in the aftertreatment, and the age of the aftertreatment. The particles measured during nucleation had a high fraction of sulfate, up to 62% of reconstructed mass. Additionally the catalyst reduced the toxicity measured in chemical and cellular assays suggesting a pathway for an inverse correlation between particle number and toxicity. The results have implications for exposure to and toxicity of diesel PM.

EPA and Port Everglades Partnership: Emission Inventories and Reduction Strategies

EPA Pesticide Factsheets

EPA’s Office of Transportation and Air Quality and Port Everglades announced a voluntary partnership to study mobile source emissions. Through this partnership, EPA and PEV agreed to work together to develop baseline and future year emission inventories.

What Do Core Obligations under the Right to Health Bring to Universal Health Coverage?

PubMed

Forman, Lisa; Beiersmann, Claudia; Brolan, Claire E; Mckee, Martin; Hammonds, Rachel; Ooms, Gorik

2016-12-01

Can the right to health, and particularly the core obligations of states specified under this right, assist in formulating and implementing universal health coverage (UHC), now included in the post-2015 Sustainable Development Goals? In this paper, we examine how core obligations under the right to health could lead to a version of UHC that is likely to advance equity and rights. We first address the affinity between the right to health and UHC as evinced through changing definitions of UHC and the health domains that UHC explicitly covers. We then engage with relevant interpretations of the right to health, including core obligations. We turn to analyze what core obligations might bring to UHC, particularly in defining what and who is covered. Finally, we acknowledge some of the risks associated with both UHC and core obligations and consider potential avenues for mitigating these risks.

A simplified approach to analyze the effectiveness of NO2 and SO2 emission reduction of coal-fired power plant from OMI retrievals

NASA Astrophysics Data System (ADS)

Bai, Yang; Wu, Lixin; Zhou, Yuan; Li, Ding

2017-04-01

Nitrogen oxides (NOX) and sulfur dioxide (SO2) emissions from coal combustion, which is oxidized quickly in the atmosphere resulting in secondary aerosol formation and acid deposition, are the main resource causing China's regional fog-haze pollution. Extensive literature has estimated quantitatively the lifetimes and emissions of NO2 and SO2 for large point sources such as coal-fired power plants and cities using satellite measurements. However, rare of these methods is suitable for sources located in a heterogeneously polluted background. In this work, we present a simplified emission effective radius extraction model for point source to study the NO2 and SO2 reduction trend in China with complex polluted sources. First, to find out the time range during which actual emissions could be derived from satellite observations, the spatial distribution characteristics of mean daily, monthly, seasonal and annual concentration of OMI NO2 and SO2 around a single power plant were analyzed and compared. Then, a 100 km × 100 km geographical grid with a 1 km step was established around the source and the mean concentration of all satellite pixels covered in each grid point is calculated by the area weight pixel-averaging approach. The emission effective radius is defined by the concentration gradient values near the power plant. Finally, the developed model is employed to investigate the characteristic and evolution of NO2 and SO2 emissions and verify the effectiveness of flue gas desulfurization (FGD) and selective catalytic reduction (SCR) devices applied in coal-fired power plants during the period of 10 years from 2006 to 2015. It can be observed that the the spatial distribution pattern of NO2 and SO2 concentration in the vicinity of large coal-burning source was not only affected by the emission of coal-burning itself, but also closely related to the process of pollutant transmission and diffusion caused by meteorological factors in different seasons. Our proposed

The Application Of Biofilter System For Reduction Of Methane Emissions From Modern Sanitary Landfills

NASA Astrophysics Data System (ADS)

Sung, K.; Park, S.

2007-12-01

Increased atmospheric concentrations of greenhouse gases (GHG) caused by anthropogenic activities has been related to global climate change. Methane, the second most important GHG after CO2, is 21 times more effective at trapping heat than CO2. Therefore, methane emission control is of utmost importance for global warming reduction. To minimize leachate production and protect groundwater resources, modern sanitary landfills are equipped with composite covers and gas collection systems. Methane from modern sanitary landfills is vented directly to the atmosphere, except for some of the largest landfills where it is recovered as energy and burned at the site. However, the efficiency of energy recovery systems in larger landfills is reduced as the amount of CH4 generated from landfill begins to decrease. In this study, the performance of a lab-scale model biofilter system was investigated to treat CH4 gas emitted from modern sanitary landfills by conducting batch and column experiments using landfill cover soil amended with earthworm cast as the filter bed medium. From the batch experiments to measure the influence of moisture content and temperature of the filter medium on CH4 removal capacity of a biofilter system, the optimum moisture content and temperature were found to be 10-15% by weight and 25-35°C, respectively. The column experiment was conducted to measure the influence of inlet CH4 concentration and CH4 loading rate on CH4 removal capacity of a biofilter system. As the inlet CH4 concentration decreased, the percentage of CH4 oxidized increased. Up to a CH4 loading rate of 2785 g CH4 m3 h- 1 (EBRT = 7.7 min), the CH4 removal efficiency of the biofilter was able to reach 100%. Based on the results of the study, the installation of a properly managed biofilter system should be capable of achieving a reduction in atmospheric CH4 emissions from modern sanitary landfills at low CH4 generation stage.

Modeling travel choices to assess potential greenhouse gas emissions reductions.

DOT National Transportation Integrated Search

2015-06-01

The transportation sector is the source of approximately 27% of total U.S. greenhouse gas : (GHG) emissions (EPA, 2015), and these emissions are projected to increase in the future : (NHTSA, 2011). Given the potentially severe impacts of climate chan...

Emissions control for ground power gas turbines

NASA Technical Reports Server (NTRS)

Rudney, R. A.; Priem, R. J.; Juhasz, A. J.; Anderson, D. N.; Mroz, T. S.; Mularz, E. J.

1977-01-01

The similarities and differences of emissions reduction technology for aircraft and ground power gas turbines is described. The capability of this technology to reduce ground power emissions to meet existing and proposed emissions standards is presented and discussed. Those areas where the developing aircraft gas turbine technology may have direct application to ground power and those areas where the needed technology may be unique to the ground power mission are pointed out. Emissions reduction technology varying from simple combustor modifications to the use of advanced combustor concepts, such as catalysis, is described and discussed.

Chloropicrin Emission Reduction by Soil Amendment with Biochar

PubMed Central

Wang, Qiuxia; Yan, Dongdong; Liu, Pengfei; Mao, Liangang; Wang, Dong; Fang, Wensheng; Li, Yuan; Ouyang, Canbin; Guo, Meixia; Cao, Aocheng

2015-01-01

Biochar has sorption capacity, and can be used to enhance the sequestration of volatile organic contaminants such as pesticides in soil. Chloropicrin (CP) is an important soil fumigant for the production of many fruit and vegetable crops, but its emissions must be minimized to reduce exposure risks and air pollution. The objective of this study was to determine the capacity of biochar to adsorb CP and the effect of biochar amendments to soil on CP emission, concentration in the soil gas phase, degradation in soil and CP bioactivity for controlling soil borne pests. CP emission and concentration in the soil air phase were measured from packed soil columns after fumigant injection at 20-cm depth and application of selected doses of biocharto the surface 5 cm soil. Laboratory incubation and fumigation experiments were conducted to determine the capacity of biochar to adsorb CP, the effects on CP degradation and, separately, CP’s bioactivity on soil borne pests in soil amended with biochar. Biochar amendment at 2% to 5% (w/w) greatly reduced total CP emission losses by 85.7% - 97.7% compared to fumigation without biochar. CP concentrations in the soil gas-phase, especially in the top 5 cm of soil, were reduced within 48 h following application. The half-life of CP decreased from 13.6 h to 6.4 h as the biochar rate increased from 0% to 5%. CP and its metabolite (dichloronitromethane) both degraded more rapidly in pure biochar than in soil. The biochar used in the present study had a maximum adsorption capacity for CP of less than 5 mg g-1. There were no negative effects on pathogen and nematode control when the biochar used in this study was less than 1% (on a weight basis) in soil. Biochar amendment to soil reduced the emissions of CP. CP concentrations in the top 5 cm of soil gas-phase were reduced. CP degradation was accelerated with the addition of biochar. The biochar used in the present study had a low adsorption capacity for CP. There were no negative effects

China CO2 emission accounts 1997-2015

NASA Astrophysics Data System (ADS)

Shan, Yuli; Guan, Dabo; Zheng, Heran; Ou, Jiamin; Li, Yuan; Meng, Jing; Mi, Zhifu; Liu, Zhu; Zhang, Qiang

2018-01-01

China is the world's top energy consumer and CO2 emitter, accounting for 30% of global emissions. Compiling an accurate accounting of China's CO2 emissions is the first step in implementing reduction policies. However, no annual, officially published emissions data exist for China. The current emissions estimated by academic institutes and scholars exhibit great discrepancies. The gap between the different emissions estimates is approximately equal to the total emissions of the Russian Federation (the 4th highest emitter globally) in 2011. In this study, we constructed the time-series of CO2 emission inventories for China and its 30 provinces. We followed the Intergovernmental Panel on Climate Change (IPCC) emissions accounting method with a territorial administrative scope. The inventories include energy-related emissions (17 fossil fuels in 47 sectors) and process-related emissions (cement production). The first version of our dataset presents emission inventories from 1997 to 2015. We will update the dataset annually. The uniformly formatted emission inventories provide data support for further emission-related research as well as emissions reduction policy-making in China.

Joint carbon footprint assessment and data envelopment analysis for the reduction of greenhouse gas emissions in agriculture production.

PubMed

Rebolledo-Leiva, Ricardo; Angulo-Meza, Lidia; Iriarte, Alfredo; González-Araya, Marcela C

2017-09-01

Operations management tools are critical in the process of evaluating and implementing action towards a low carbon production. Currently, a sustainable production implies both an efficient resource use and the obligation to meet targets for reducing greenhouse gas (GHG) emissions. The carbon footprint (CF) tool allows estimating the overall amount of GHG emissions associated with a product or activity throughout its life cycle. In this paper, we propose a four-step method for a joint use of CF assessment and Data Envelopment Analysis (DEA). Following the eco-efficiency definition, which is the delivery of goods using fewer resources and with decreasing environmental impact, we use an output oriented DEA model to maximize production and reduce CF, taking into account simultaneously the economic and ecological perspectives. In another step, we stablish targets for the contributing CF factors in order to achieve CF reduction. The proposed method was applied to assess the eco-efficiency of five organic blueberry orchards throughout three growing seasons. The results show that this method is a practical tool for determining eco-efficiency and reducing GHG emissions. Copyright © 2017 Elsevier B.V. All rights reserved.

Dramatic reduction of sulfur dioxide emission in Northeastern China in the last decade

NASA Astrophysics Data System (ADS)

Yuan, J.

2017-12-01

Analysis of spatial and temporal variations of sulfur dioxide concentration in planetary boundary layer were conducted. The data were generated by NASA satellite daily from October of 2004 and were obtained through NASA Giovanni. The global monthly mean spatial distribution of sulfur dioxide showed several hot spots including: several spots on some islands in the Pacific Ocean, several spots in central America, and central Africa. Most of these hot spots of sulfur dioxide are related to known active volcanos. The biggest hot spot of sulfur dioxide were observed in Northeastern China. While high concentration sulfur dioxide was still observed in Northeastern China in 2017. The area averaged concentration of sulfur dioxide declined dramatically since its peak in 2008. This temporal trend indicates that sulfur reduction effort has been effective in the last decade or post 2008 financial crisis recovery lead an industry less sulfur dioxide emission.

The importance of health co-benefits in macroeconomic assessments of UK Greenhouse Gas emission reduction strategies.

PubMed

Jensen, Henning Tarp; Keogh-Brown, Marcus R; Smith, Richard D; Chalabi, Zaid; Dangour, Alan D; Davies, Mike; Edwards, Phil; Garnett, Tara; Givoni, Moshe; Griffiths, Ulla; Hamilton, Ian; Jarrett, James; Roberts, Ian; Wilkinson, Paul; Woodcock, James; Haines, Andy

We employ a single-country dynamically-recursive Computable General Equilibrium model to make health-focussed macroeconomic assessments of three contingent UK Greenhouse Gas (GHG) mitigation strategies, designed to achieve 2030 emission targets as suggested by the UK Committee on Climate Change. In contrast to previous assessment studies, our main focus is on health co-benefits additional to those from reduced local air pollution. We employ a conservative cost-effectiveness methodology with a zero net cost threshold. Our urban transport strategy (with cleaner vehicles and increased active travel) brings important health co-benefits and is likely to be strongly cost-effective; our food and agriculture strategy (based on abatement technologies and reduction in livestock production) brings worthwhile health co-benefits, but is unlikely to eliminate net costs unless new technological measures are included; our household energy efficiency strategy is likely to breakeven only over the long term after the investment programme has ceased (beyond our 20 year time horizon). We conclude that UK policy makers will, most likely, have to adopt elements which involve initial net societal costs in order to achieve future emission targets and longer-term benefits from GHG reduction. Cost-effectiveness of GHG strategies is likely to require technological mitigation interventions and/or demand-constraining interventions with important health co-benefits and other efficiency-enhancing policies that promote internalization of externalities. Health co-benefits can play a crucial role in bringing down net costs, but our results also suggest the need for adopting holistic assessment methodologies which give proper consideration to welfare-improving health co-benefits with potentially negative economic repercussions (such as increased longevity).

Analysis of CO2, CO and HC emission reduction in automobiles

NASA Astrophysics Data System (ADS)

Balan, K. N.; Valarmathi, T. N.; Reddy, Mannem Soma Harish; Aravinda Reddy, Gireddy; Sai Srinivas, Jammalamadaka K. M. K.; Vasan

2017-05-01

In the present scenario, the emission from automobiles is becoming a serious problem to the environment. Automobiles, thermal power stations and Industries majorly constitute to the emission of CO2, CO and HC. Though the CO2 available in the atmosphere will be captured by oceans, grasslands; they are not enough to control CO2 present in the atmosphere completely. Also advances in engine and vehicle technology continuously to reduce the emission from engine exhaust are not sufficient to reduce the HC and CO emission. This work concentrates on design, fabrication and analysis to reduce CO2, CO and HC emission from exhaust of automobiles by using molecular sieve 5A of 1.5mm. In this paper, the details of the fabrication, results and discussion about the process are discussed.

Diesel Emissions Quantifier (DEQ)

EPA Pesticide Factsheets

.The Diesel Emissions Quantifier (Quantifier) is an interactive tool to estimate emission reductions and cost effectiveness. Publications EPA-420-F-13-008a (420f13008a), EPA-420-B-10-035 (420b10023), EPA-420-B-10-034 (420b10034)

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

Evaluating the effectiveness of joint emission control policies on the reduction of ambient VOCs: Implications from observation during the 2014 APEC summit in suburban Beijing

NASA Astrophysics Data System (ADS)

Li, Kun; Li, Junling; Wang, Weigang; Tong, Shengrui; Liggio, John; Ge, Maofa

2017-09-01

Ambient volatile organic compounds (VOCs) at a suburban Beijing site were on-line detected using proton transfer reaction-mass spectrometry (PTR-MS) during autumn of 2014, near the location of the Asia-Pacific Economic Cooperation (APEC) summit. During the APEC summit, the Chinese government enacted strict emission control policies. It was found that VOC concentrations only slightly decreased during the first emission control period (EC I), when control policies were performed in Beijing and 5 cities along the Tai-hang Mountains. However, most of the VOCs (10 out of 12 non-biogenic species) significantly decreased (more than 40%) during the second emission control period (EC II), when control policies were carried out in 16 cities including Beijing, Tianjin, 8 cities of Hebei province and 6 cities of Shandong province. Also the ratio of toluene and benzene decreased during EC II, likely because the emission control policies changed the proportions of different anthropogenic sources. Using the positive matrix factorization (PMF) source apportionment method, five factors are analyzed: (1) vehicle + fuel, (2) solvent, (3) biomass burning, (4) secondary, and (5) background + long-lived. Among them, vehicle + fuel, solvent and biomass burning contribute most of the VOCs concentrations (60%-80%) during the polluted periods and are affected most by emission control policies. During EC II, the reductions of vehicle + fuel, solvent, biomass burning and secondary species were all no less than 50%. Overall, when emission control policies were carried out in many North China Plain (NCP) cities (i.e. EC II), the VOC concentrations of suburban Beijing markedly decreased. This indicates the cross-regional joint-control policies have a large influence on reductions of organic gas species. The findings of this study have vital implications for helping formulate effective emission control policies in China and other countries.

500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide emissions from coal-fired boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sorge, J.N.; Larrimore, C.L.; Slatsky, M.D.

1997-12-31

This paper discusses the technical progress of a US Department of Energy Innovative Clean Coal Technology project demonstrating advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NOx) emissions from coal-fired boilers. The primary objectives of the demonstration is to determine the long-term NOx reduction performance of advanced overfire air (AOFA), low NOx burners (LNB), and advanced digital control optimization methodologies applied in a stepwise fashion to a 500 MW boiler. The focus of this paper is to report (1) on the installation of three on-line carbon-in-ash monitors and (2) the design and results to date from the advancedmore » digital control/optimization phase of the project.« less

Model assessment of atmospheric pollution control schemes for critical emission regions

NASA Astrophysics Data System (ADS)

Zhai, Shixian; An, Xingqin; Liu, Zhao; Sun, Zhaobin; Hou, Qing

2016-01-01

In recent years, the atmospheric environment in portions of China has become significantly degraded and the need for emission controls has become urgent. Because more international events are being planned, it is important to implement air quality assurance targeted at significant events held over specific periods of time. This study sets Yanqihu (YQH), Beijing, the location of the 2014 Beijing APEC (Asia-Pacific Economic Cooperation) summit, as the target region. By using the atmospheric inversion model FLEXPART, we determined the sensitive source zones that had the greatest impact on the air quality of the YQH region in November 2012. We then used the air-quality model Models-3/CMAQ and a high-resolution emissions inventory of the Beijing-Tianjian-Hebei region to establish emission reduction tests for the entire source area and for specific sensitive source zones. This was achieved by initiating emission reduction schemes at different ratios and different times. The results showed that initiating a moderate reduction of emissions days prior to a potential event is more beneficial to the air quality of Beijing than initiating a high-strength reduction campaign on the day of the event. The sensitive source zone of Beijing (BJ-Sens) accounts for 54.2% of the total source area of Beijing (BJ), but its reduction effect reaches 89%-100% of the total area, with a reduction efficiency 1.6-1.9 times greater than that of the entire area. The sensitive source zone of Huabei (HuaB-Sens.) only represents 17.6% of the total area of Huabei (HuaB), but its emission reduction effect reaches 59%-97% of the entire area, with a reduction efficiency 4.2-5.5 times greater than that of the total area. The earlier that emission reduction measures are implemented, the greater the effect they have on preventing the transmission of pollutants. In addition, expanding the controlling areas to sensitive provinces and cities around Beijing (HuaB-sens) can significantly accelerate the reduction

Comparative estimation of soil and plant pollution in the impact area of air emissions from an aluminium plant after technogenic load reduction.

PubMed

Evdokimova, Galina A; Mozgova, Natalya P

2015-01-01

The work provides a comparative analysis of changes in soil properties in the last 10-13 years along the pollution gradient of air emissions from Kandalaksha aluminium plant in connection with the reduction of their volume. The content of the priority pollutant fluorine (F) in atmospheric precipitation and in the organic horizon of soil in the plant impact zone significantly decreased in 2011-2013 compared to 2001. The aluminium concentrations reduced only in immediate proximity to the plant (2 km). The fluorine, calcium (Ca) and magnesium (Mg) concentrations are higher in liquid phase compared to solid phase thus these elements can migrated to greater distances from the pollution source (up to 15-20 km). Silicon (Si), aluminium (Al), iron (Fe) and phosphorus (P) can be found only in solid phases and in fall-out within the 5 km. The acidity of soil litter reduced by 2 pH units in the proximity to the plot within the 2 km. The zone of maximum soil contamination decreased from 2.5 km to 1.5 km from the emission source, the zones of heavy and moderate pollution reduced by 5 km in connection with the reduction of pollutant emissions in the plant. A high correlation between the fluorine concentrations in vegetables and litter was found. Higher fluorine concentrations in the soil result in its accumulation in plants. Mosses accumulate fluorine most intensively.

Impact of alternative fuels on emissions characteristics of a gas turbine engine - part 1: gaseous and particulate matter emissions.

PubMed

Lobo, Prem; Rye, Lucas; Williams, Paul I; Christie, Simon; Uryga-Bugajska, Ilona; Wilson, Christopher W; Hagen, Donald E; Whitefield, Philip D; Blakey, Simon; Coe, Hugh; Raper, David; Pourkashanian, Mohamed

2012-10-02

Growing concern over emissions from increased airport operations has resulted in a need to assess the impact of aviation related activities on local air quality in and around airports, and to develop strategies to mitigate these effects. One such strategy being investigated is the use of alternative fuels in aircraft engines and auxiliary power units (APUs) as a means to diversify fuel supplies and reduce emissions. This paper summarizes the results of a study to characterize the emissions of an APU, a small gas turbine engine, burning conventional Jet A-1, a fully synthetic jet fuel, and other alternative fuels with varying compositions. Gas phase emissions were measured at the engine exit plane while PM emissions were recorded at the exit plane as well as 10 m downstream of the engine. Five percent reduction in NO(x) emissions and 5-10% reduction in CO emissions were observed for the alternative fuels. Significant reductions in PM emissions at the engine exit plane were achieved with the alternative fuels. However, as the exhaust plume expanded and cooled, organic species were found to condense on the PM. This increase in organic PM elevated the PM mass but had little impact on PM number.

Reduction of Greenhouse Gas and Criteria Pollutant Emissions by Direct Conversion of Associated Flare Gas to Synthetic Fuels at Oil Wellheads

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, Eric C; Zhang, Yi Min; Schuetzle, Dennis

This study describes the results of a 'well-to-wheel' life cycle assessment (LCA) carried out to determine the potential greenhouse gas and criteria pollutant emission reductions that could be achieved by converting associated flare gas directly to synthetic fuels at oil wellheads in the US and globally. A Greyrock Flare Gas-to-Fuels(TM) conversion process at an Ohio oil well was used as the base case for this LCA. The liquid fuel produced directly from associated gas is comprised primarily of premium synthetic diesel with a small amount of synthetic gasoline. In this LCA scenario, the synthetic diesel and synthetic gasoline are blendedmore » at 20 and 10 vol% with petroleum diesel and gasoline, respectively. While the synthetic diesel fuel can be used as is (100%), the 20 vol% synthetic diesel blend (with petroleum diesel) was found to significantly improve engine performance, increase fuel economy, and reduce emissions. The direct conversion of associated gas to synthetic diesel fuels globally could reduce emissions of CO2 and CH4 by up to 356 and 5.96 million metric tons/year, respectively, resulting in the reduction of greenhouse gases (GHGs) by about 113.3 and 92.2% (20 year global warming potential) and 73.8 and 50.7% (100 year global warming potential) for synthetic diesel and gasoline fuels when compared to petroleum-derived gasoline fuels, respectively. Likewise, diesel criteria emissions could be reduced globally by up to 23.3, 0.374, 42.4, and 61.3 million metric tons/year globally for CO, particulates, NOx, and hydrocarbons, respectively. The potential economic benefit of this approach is that up to 5.30 and 71.1 billion liters of synthetic fuels could be produced each year in the US and globally from associated gas, respectively.« less

How Well Do We Know the Future of CO2 Emissions? Projecting Fleet Emissions from Light Duty Vehicle Technology Drivers.

PubMed

Martin, Niall P D; Bishop, Justin D K; Boies, Adam M

2017-03-07

While the UK has committed to reduce CO 2 emissions to 80% of 1990 levels by 2050, transport accounts for nearly a fourth of all emissions and the degree to which decarbonization can occur is highly uncertain. We present a new methodology using vehicle and powertrain parameters within a Bayesian framework to determine the impact of engineering vehicle improvements on fuel consumption and CO 2 emissions. Our results show how design changes in vehicle parameters (e.g., mass, engine size, and compression ratio) result in fuel consumption improvements from a fleet-wide mean of 5.6 L/100 km in 2014 to 3.0 L/100 km by 2030. The change in vehicle efficiency coupled with increases in vehicle numbers and fleet-wide activity result in a total fleet-wide reduction of 41 ± 10% in 2030, relative to 2012. Concerted internal combustion engine improvements result in a 48 ± 10% reduction of CO 2 emissions, while efforts to increase the number of diesel vehicles within the fleet had little additional effect. Increasing plug-in and all-electric vehicles reduced CO 2 emissions by less (42 ± 10% reduction) than concerted internal combustion engines improvements. However, if the grid decarbonizes, electric vehicles reduce emissions by 45 ± 9% with further reduction potential to 2050.

Project identification for methane reduction options

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerr, T.

1996-12-31

This paper discusses efforts directed at reduction in emission of methane to the atmosphere. Methane is a potent greenhouse gas, which on a 20 year timeframe may present a similar problem to carbon dioxide. In addition, methane causes additional problems in the form of smog and its longer atmospheric lifetime. The author discusses strategies for reducing methane emission from several major sources. This includes landfill methane recovery, coalbed methane recovery, livestock methane reduction - in the form of ruminant methane reduction and manure methane recovery. The author presents examples of projects which have implemented these ideas, the economics of themore » projects, and additional gains which come from the projects.« less

MODELING ASSESSMENT OF THE IMPACT OF NITROGEN OXIDES EMISSION REDUCTIONS ON OZONE AIR QUALITY IN THE EASTERN UNITED STATES: OFFSETTING INCREASES IN ENERGY USE

EPA Science Inventory

The objective of this study is to examine changes in ambient ozone concentrations estimated by a photochemical air quality model in response to the NOx emission reductions imposed on the utility sector. To accomplish this task, CMAQ air quality model simulations were performe...

Priority-setting for achieving universal health coverage

PubMed Central

Chalkidou, Kalipso; Glassman, Amanda; Marten, Robert; Vega, Jeanette; Tritasavit, Nattha; Gyansa-Lutterodt, Martha; Seiter, Andreas; Kieny, Marie Paule; Hofman, Karen; Culyer, Anthony J

2016-01-01

Abstract Governments in low- and middle-income countries are legitimizing the implementation of universal health coverage (UHC), following a United Nation’s resolution on UHC in 2012 and its reinforcement in the sustainable development goals set in 2015. UHC will differ in each country depending on country contexts and needs, as well as demand and supply in health care. Therefore, fundamental issues such as objectives, users and cost–effectiveness of UHC have been raised by policy-makers and stakeholders. While priority-setting is done on a daily basis by health authorities – implicitly or explicitly – it has not been made clear how priority-setting for UHC should be conducted. We provide justification for explicit health priority-setting and guidance to countries on how to set priorities for UHC. PMID:27274598

A study of cooling time reduction of interferometric cryogenic gravitational wave detectors using a high-emissivity coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakakibara, Y.; Yamamoto, K.; Chen, D.

In interferometric cryogenic gravitational wave detectors, there are plans to cool mirrors and their suspension systems (payloads) in order to reduce thermal noise, that is, one of the fundamental noise sources. Because of the large payload masses (several hundred kg in total) and their thermal isolation, a cooling time of several months is required. Our calculation shows that a high-emissivity coating (e.g. a diamond-like carbon (DLC) coating) can reduce the cooling time effectively by enhancing radiation heat transfer. Here, we have experimentally verified the effect of the DLC coating on the reduction of the cooling time.

Evaluation of the Impact of Low Emission Zone and Heavy Traffic Ban in Munich (Germany) on the Reduction of PM10 in Ambient Air

PubMed Central

Fensterer, Veronika; Küchenhoff, Helmut; Maier, Verena; Wichmann, Heinz-Erich; Breitner, Susanne; Peters, Annette; Gu, Jianwei; Cyrys, Josef

2014-01-01

Concentrations of ambient fine particles (PM10: particles with an aerodynamic diameter ≤ 10 µm) are still exceeding current air quality standards in many European cities. In Munich (Germany), low emission zone and transit bans for heavy-duty vehicles were introduced in 2008 aiming at reduction of traffic emissions contribution to PM10. The effects of those measures on PM10 mass concentrations in Munich were investigated with a semiparametric regression model for modeling PM10 levels adjusted for time, background pollution, public holidays and wind direction. The reduction of PM10 concentration after the introduction of the measures was larger at a traffic monitoring site (13.0 %, 19.6 % in summer, and 6.8 % in winter) and smaller in urban background (4.5 %, 5.7 % in summer, and 3.2 % in winter). The effect was most pronounced on Fridays and on the weekends in summer. PMID:24828081

50% REDUCTION IN GLOBAL GHG EMISSION BY 2050 AND ITS IMPLICATION

NASA Astrophysics Data System (ADS)

Fujimori, Shinichiro; Masui, Toshihiko; Matsuoka, Yuzuru

To prevent the global temperature increase by two degrees, global greenhouse gas emission in 2050 should be cut by half relative to its 1990 level. This study shows following three things by using multi regions and sectors recursive dynamic type computable general equilibrium model. One is the feasibility of that global emission target. The others are the counter measures and the impact on the macro economy, if that target were feasible. In addition, the scenarios with and without international emission trading are implemented and the effect of the trading is analyzed. As a result, that target can be achieved. The marginal abatement cost is 750/tCO2-eq in 2050. Energy efficiency improvement, renewable energy and carbon capture and storage technologies are the main players as counter measures. If the emission trading is available freely, GDP loss is 4.5% globally in 2050. Otherwise, the loss is increased to 6.1%. The emission trading mechanism is also one of the important measures.

Combined heat and power systems for commercial buildings: investigating cost, emissions, and primary energy reduction based on system components

NASA Astrophysics Data System (ADS)

Smith, Amanda D.

Combined heat and power (CHP) systems produce electricity and useful heat from fuel. When power is produced near a building which consumes power, transmission losses are averted, and heat which is a byproduct of power production may be useful to the building. That thermal energy can be used for hot water or space heating, among other applications. This dissertation focuses on CHP systems using natural gas, a common fuel, and systems serving commercial buildings in the United States. First, the necessary price difference between purchased electricity and purchased fuel is analyzed in terms of the efficiencies of system components by comparing CHP with a conventional separate heat and power (SHP) configuration, where power is purchased from the electrical grid and heat is provided by a gas boiler. Similarly, the relationship between CDE due to electricity purchases and due to fuel purchases is analyzed as well as the relationship between primary energy conversion factors for electricity and fuel. The primary energy conversion factor indicates the quantity of source energy necessary to produce the energy purchased at the site. Next, greenhouse gas emissions are investigated for a variety of commercial buildings using CHP or SHP. The relationship between the magnitude of the reduction in emissions and the parameters of the CHP system is explored. The cost savings and reduction in primary energy consumption are evaluated for the same buildings. Finally, a CHP system is analyzed with the addition of a thermal energy storage (TES) component, which can store excess thermal energy and deliver it later if necessary. The potential for CHP with TES to reduce cost, emissions, and primary energy consumption is investigated for a variety of buildings. A case study is developed for one building for which TES does provide additional benefits over a CHP system alone, and the requirements for a water tank TES device are examined.

Pricing, Carbon Emission Reduction, Low-Carbon Promotion and Returning Decision in a Closed-Loop Supply Chain under Vertical and Horizontal Cooperation

PubMed Central

Li, Hui; Wang, Chuanxu; Shang, Meng; Ou, Wei

2017-01-01

In this paper, we examine the influences of vertical and horizontal cooperation models on the optimal decisions and performance of a low-carbon closed-loop supply chain (CLSC) with a manufacturer and two retailers, and study optimal operation in the competitive pricing, competitive the low-carbon promotion, the carbon emission reduction, the used-products collection and the profits. We consider the completely decentralized model, M-R vertical cooperation model, R-R horizontal cooperation model, M-R-R vertical and horizontal cooperation model and completely centralized model, and also identify the optimal decision results and profits. It can be observed from a systematic comparison and numerical analysis that the completely centralized model is best in all optimal decision results among all models. In semi-cooperation, the M-R vertical cooperation model is positive, the R-R horizontal cooperation model is passive, and the positivity of the M-R-R vertical and horizontal cooperation model decreases with competitive intensity increasing in the used-products returning, carbon emissions reduction level, low-carbon promotion effort and the profits of the manufacturer and the entire supply chain. PMID:29104268

Analysis of a long-term measurement of air pollutants (2007-2011) in North China Plain (NCP); Impact of emission reduction during the Beijing Olympic Games.

PubMed

Xu, Ruiguang; Tang, Guiqian; Wang, Yuesi; Tie, Xuexi

2016-09-01

Five years measurements were used to evaluate the effect of emission controls on the changes of air pollutants in Beijing and its surroundings in the NCP during 2008 Olympic Games (2008OG). The major challenge of this study was to filter out the effect of variability of meteorological conditions, when compared the air pollutants during the game to non-game period. We used four-year (2007, 2009-2011) average as the Non-2008OG to smooth the temporal variability caused by meteorological parameters. To study the spatial variability and regional transport, 6 sites (urban, rural, a mega city, a heavy industrial city, and a remote site) were selected. The result showed that the annually meteorological variability was significantly reduced. Such as, in BJ the differences between 2008OG and 5-years averaged values were 2.7% for relative humidity and 0.6% for wind speed. As a result, the anomaly of air pollutants between 2008OG and Non-2008OG can largely attribute to the emission control. The comparison showed that the major pollutants (PM10, PM2.5, NO, NOx) at the 6 sites in 2008OG were consistently lowered. For example, PM2.5 in BJ decreased from 75 to 45 μg/m(3) (40% reduction). However, the emission controls had minor effect on O3 concentrations (1% reduction). In contrast, the O3 precursor (NOx) reduced from 19.7 to 13.2 ppb (33% reduction). The in-sensitivity between NOx and O3 suggested that the O3 formation was under VOCs control condition in NCP, showing that strong VOC emission control is needed in order to significantly reduce O3 concentration in the region. Copyright © 2016 Elsevier Ltd. All rights reserved.

Estimates of ozone response to various combinations of NO(x) and VOC emission reductions in the eastern United States

NASA Technical Reports Server (NTRS)

Roselle, Shawn J.; Schere, Kenneth L.; Chu, Shao-Hang

1994-01-01

There is increasing recognition that controls on NO(x) emissions may be necessary, in addition to existing and future Volatile Organic Compounds (VOC) controls, for the abatement of ozone (O3) over portions of the United States. This study compares various combinations of anthropogenic NO(x) and VOC emission reductions through a series of model simulations. A total of 6 simulations were performed with the Regional Oxidant Model (ROM) for a 9-day period in July 1988. Each simulation reduced anthropogenic NO(x) and VOC emissions across-the-board by different amounts. Maximum O3 concentrations for the period were compared between the simulations. Comparison of the simulations suggests that: (1) NO(x) controls may be more effective than VOC controls in reducing peak O3 over most of the eastern United States; (2) VOC controls are most effective in urban areas having large sources of emissions; (3) NO(x) controls may increase O3 near large point sources; and (4) the benefit gained from increasing the amount of VOC controls may lessen as the amount of NO(x) control is increased. This paper has been reviewed in accordance with the U.S. Environmental Protection Agency's peer and administrative review policies and approved for presentation and publication. Mention of trade names or commercial products does not constitute endorsement or recommendation for use.

Spatial analysis on China's regional air pollutants and CO2 emissions: emission pattern and regional disparity

NASA Astrophysics Data System (ADS)

Dong, Liang; Liang, Hanwei

2014-08-01

China has suffered from serious air pollution and CO2 emission. Challenges of emission reduction policy not only come from technology advancement, but also generate from the fact that, China has pronounced disparity between regions, in geographical and socioeconomic. How to deal with regional disparity is important to achieve the reduction target effectively and efficiently. This research conducts a spatial analysis on the emission patterns of three air pollutants named SO2, NOx and PM2.5, and CO2, in China's 30 provinces, applied with spatial auto-correlation and multi regression modeling. We further analyze the regional disparity and inequity issues with the approach of Lorenz curve and Gini coefficient. Results highlight that: there is evident cluster effect for the regional air pollutants and CO2 emissions. While emission amount increases from western regions to eastern regions, the emission per GDP is in inverse trend. The Lorenz curve shows an even larger unequal distribution of GDP/emissions than GDP/capita in 30 regions. Certain middle and western regions suffers from a higher emission with lower GDP, which reveal the critical issue of emission leakage. Future policy making to address such regional disparity is critical so as to promote the emission control policy under the “equity and efficiency” principle.

Health Cobenefits and Transportation-Related Reductions in Greenhouse Gas Emissions in the San Francisco Bay Area

PubMed Central

Woodcock, James; Co, Sean; Ostro, Bart; Fanai, Amir; Fairley, David

2013-01-01

Objectives. We quantified health benefits of transportation strategies to reduce greenhouse gas emissions (GHGE). Methods. Statistics on travel patterns and injuries, physical activity, fine particulate matter, and GHGE in the San Francisco Bay Area, California, were input to a model that calculated the health impacts of walking and bicycling short distances usually traveled by car or driving low-emission automobiles. We measured the change in disease burden in disability-adjusted life years (DALYs) based on dose–response relationships and the distributions of physical activity, particulate matter, and traffic injuries. Results: Increasing median daily walking and bicycling from 4 to 22 minutes reduced the burden of cardiovascular disease and diabetes by 14% (32 466 DALYs), increased the traffic injury burden by 39% (5907 DALYS), and decreased GHGE by 14%. Low-carbon driving reduced GHGE by 33.5% and cardiorespiratory disease burden by less than 1%. Conclusions: Increased physical activity associated with active transport could generate a large net improvement in population health. Measures would be needed to minimize pedestrian and bicyclist injuries. Together, active transport and low-carbon driving could achieve GHGE reductions sufficient for California to meet legislative mandates. PMID:23409903

Work Truck Idling Reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2017-03-01

Hybrid utility trucks, with auxiliary power sources for on-board equipment, significantly reduce unnecessary idling resulting in fuel costs savings, less engine wear, and reduction in noise and emissions.

A Method to Exchange Air Nitrogen Emission Reductions for Watershed Nitrogen Load Reductions

EPA Science Inventory

Presentation of the method developed for the Chesapeake Bay Program to estimate changes in nitrogen loading to Chesapeake due to changes in Bay State state-level nitrogen oxide emissions to support air-water trading by the Bay States. Type for SticsUnder AMAD Application QAPP, QA...

China CO2 emission accounts 1997–2015

PubMed Central

Shan, Yuli; Guan, Dabo; Zheng, Heran; Ou, Jiamin; Li, Yuan; Meng, Jing; Mi, Zhifu; Liu, Zhu; Zhang, Qiang

2018-01-01

China is the world’s top energy consumer and CO2 emitter, accounting for 30% of global emissions. Compiling an accurate accounting of China’s CO2 emissions is the first step in implementing reduction policies. However, no annual, officially published emissions data exist for China. The current emissions estimated by academic institutes and scholars exhibit great discrepancies. The gap between the different emissions estimates is approximately equal to the total emissions of the Russian Federation (the 4th highest emitter globally) in 2011. In this study, we constructed the time-series of CO2 emission inventories for China and its 30 provinces. We followed the Intergovernmental Panel on Climate Change (IPCC) emissions accounting method with a territorial administrative scope. The inventories include energy-related emissions (17 fossil fuels in 47 sectors) and process-related emissions (cement production). The first version of our dataset presents emission inventories from 1997 to 2015. We will update the dataset annually. The uniformly formatted emission inventories provide data support for further emission-related research as well as emissions reduction policy-making in China. PMID:29337312

Power Plant Emission Reductions Using a Generation Performance Standard

EIA Publications

2001-01-01

In an earlier analysis completed in response to a request received from Representative David McIntosh, Chairman of the Subcommittee on National Economic Growth, Natural Resources, and Regulatory Affairs, the Energy Information Administration analyzed the impacts of power sector caps on nitrogen oxides, sulfur dioxide, and carbon dioxide emissions, assuming a policy instrument patterned after the sulfur dioxide allowance program created in the Clean Air Act Amendments of 1990. This paper compares the results of that work with the results of an analysis that assumes the use of a dynamic generation performance standard as an instrument for reducing carbon dioxide emissions.

Transportation Energy Futures Series: Effects of Travel Reduction and Efficient Driving on Transportation: Energy Use and Greenhouse Gas Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porter, C. D.; Brown, A.; DeFlorio, J.

2013-03-01

Since the 1970s, numerous transportation strategies have been formulated to change the behavior of drivers or travelers by reducing trips, shifting travel to more efficient modes, or improving the efficiency of existing modes. This report summarizes findings documented in existing literature to identify strategies with the greatest potential impact. The estimated effects of implementing the most significant and aggressive individual driver behavior modification strategies range from less than 1% to a few percent reduction in transportation energy use and GHG emissions. Combined strategies result in reductions of 7% to 15% by 2030. Pricing, ridesharing, eco-driving, and speed limit reduction/enforcement strategiesmore » are widely judged to have the greatest estimated potential effect, but lack the widespread public acceptance needed to accomplish maximum results. This is one of a series of reports produced as a result of the Transportation Energy Futures (TEF) project, a Department of Energy-sponsored multi-agency project initiated to pinpoint underexplored strategies for abating GHGs and reducing petroleum dependence related to transportation.« less

Transportation Energy Futures Series. Effects of Travel Reduction and Efficient Driving on Transportation. Energy Use and Greenhouse Gas Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porter, C. D.; Brown, A.; DeFlorio, J.

2013-03-01

Since the 1970s, numerous transportation strategies have been formulated to change the behavior of drivers or travelers by reducing trips, shifting travel to more efficient modes, or improving the efficiency of existing modes. This report summarizes findings documented in existing literature to identify strategies with the greatest potential impact. The estimated effects of implementing the most significant and aggressive individual driver behavior modification strategies range from less than 1% to a few percent reduction in transportation energy use and GHG emissions. Combined strategies result in reductions of 7% to 15% by 2030. Pricing, ridesharing, eco-driving, and speed limit reduction/enforcement strategiesmore » are widely judged to have the greatest estimated potential effect, but lack the widespread public acceptance needed to accomplish maximum results. This is one of a series of reports produced as a result of the Transportation Energy Futures (TEF) project, a Department of Energy-sponsored multi-agency project initiated to pinpoint underexplored strategies for abating GHGs and reducing petroleum dependence related to transportation.« less

Can the AYUSH system be instrumental in achieving universal health coverage in India?

PubMed

Samal, Janmejaya; Dehury, Ranjit Kumar

2018-01-01

Universal health coverage (UHC) in the Indian context is understood as easily accessible and affordable health services for all citizens. The Planning Commission of India constituted a High Level Expert Group (HLEG) in October 2010 for the purpose of drafting the guidelines of UHC. While the primary focus of UHC is to provide financial protection to all citizens, its delivery requires an adequate health infrastructure, skilled health human resources, and access to affordable drugs and technologies so that all people receive the level and quality of care they are entitled to. This paper attempts to link the ayurveda, yoga and naturopathy, unani, siddha and homoeopathy (AYUSH) systems of medicine with UHC. Here, the AYUSH system refers to the AYUSH workforce, therapeutics and principles, and their individual role in delivering UHC to the citizens of India. In outlining the role of AYUSH, the paper lays stress on the 10 guiding principles of UHC, as proposed by the HLEG. However, as the AYUSH system is not the principal health service provider in India, the dominant system being that of allopathic medicine, a few components of UHC may not fit neatly into the AYUSH system. This paper has adopted the definition of UHC quoted by the HLEG.

An Overview of Low-Emission Combustion Research

NASA Technical Reports Server (NTRS)

DelRosario, Ruben

2014-01-01

An overview of research efforts at NASA Glenn Research Center (GRC) in low-emission combustion technology that have made a significant impact on the Nitrogen Oxides (NOx) emission reduction in aircraft propulsion will be presented. The technology advancements and their impact on aircraft emissions will be discussed in the context of NASAs Aeronautics Research Mission Directorate (ARMD) high-level goals in fuel burn, noise and emission reductions. The highlights of the research presented will show how the past and current efforts have laid the foundation for the engines that are flying today as well as how the continued technology advancements will significantly influence the next generation of aviation propulsion system designs.

Overview of the U.S. Environmental Protection Agency's Hazardous Air Pollutant Early Reduction Program.

PubMed

Laznow, J; Daniel, J

1992-01-01

Under provision of the Clean Air Act Amendments of 1990 Title III, the EPA has proposed a regulation (Early Reduction Program) to allow a six-year compliance extension from Maximum Achievable Control Technology (MACT) standards for sources that voluntarily reduce emissions of Hazardous Air Pollutants (HAPs) by 90 percent or more (95 percent or more for particulates) from a base year of 1987 or later. The emission reduction must be made before the applicable MACT standard is proposed for the source category or be subject to an enforceable commitment to achieve the reduction by January 1, 1994 for sources subject to MACT standards prior to 1994. The primary purpose of this program is to encourage reduction of HAPs emissions sooner than otherwise required. Industry would be allowed additional time in evaluating emission reduction options and developing more cost-effective compliance strategies, although, under strict guidelines to ensure actual, significant and verifiable emission reductions occur.

Supplementation with whole cottonseed causes long-term reduction of methane emissions from lactating dairy cows offered a forage and cereal grain diet.

PubMed

Grainger, C; Williams, R; Clarke, T; Wright, A-D G; Eckard, R J

2010-06-01

The objective of our work was to supplement a forage and cereal diet of lactating dairy cows with whole cottonseed (WCS) for 12 wk and to determine whether the expected reduction in CH(4) would persist. A secondary objective was to determine the effect of supplementing the diet with WCS on milk yield and rumen function over the 12-wk feeding period. Fifty lactating cows were randomly allocated to 1 of 2 diets (control or WCS). The 2 separate groups were each offered, on average, 4.2 kg of DM/cow per day of alfalfa hay (a.m.) and 6.6 kg of DM/cow per day of ryegrass silage (p.m.) on the ground in bare paddocks each day for 12 wk. Cows in each group were also individually offered dietary supplements for 12 wk in a feed trough at milking times of 5.4 kg of DM/cow per day of cracked wheat grain and 0.5 kg of DM/cow per day of cottonseed meal (control) or 2.8 kg of DM/cow per day of cracked wheat grain and 2.61 kg of DM/cow per day of WCS. The 2 diets were formulated to be similar in their concentrations of CP and ME, but the WCS diet was designed to have a higher fat concentration. Samples of rumen fluid were collected per fistula from the rumen approximately 4 h after grain feeding in the morning. Samples were taken from 8 cows (4 cows/diet) on 2 consecutive days in wk 2 of the covariate and wk 3, 6, 10, and 12 of treatment and analyzed for volatile fatty acids, ammonia-N, methanogens, and protozoa. The reduction in CH(4) emissions (g/d) because of WCS supplementation increased from 13% in wk 3 to 23% in wk 12 of treatment. Similarly, the reduction in CH(4) emissions (g/kg of DMI) increased from 5.1% in wk 3 to 14.5% in wk 12 of treatment. It was calculated that the average reduction in CH(4) emissions over the 12-wk period was 2.9% less CH(4) per 1% added fat, increasing from 1.5% in wk 3 to 4.4% less CH(4) in wk 12. There was no effect of WCS supplementation on rumen ammonia-N, rumen volatile fatty acids, rumen methanogens, and rumen protozoa. On average over the 12

Options for lowering U.S. carbon dioxide emissions

NASA Astrophysics Data System (ADS)

Bierbaum, Rosina M.; Friedman, Robert M.; Levenson, Howard; Rapoport, Richard D.; Sundt, Nick

1992-03-01

The United States can decrease its emissions of carbon dioxide (CO2) to as much as 35 percent below 1987 levels within the next 25 years by adopting an aggressive package of policies crossing all sectors of the economy. Such emissions reductions will be difficult to achieve and may be costly, but no major technological breakthroughs are needed. In this paper, we identify a ``Tough'' package of energy conservation, energy supply, and forest managment practices to accomplish this level of emissions reductions. We also present a package of cost-effective, ``Moderate'' technical options, which if adopted, would hold CO2 emissions to about 15-percent increase over 1987 levels by 2015. In constrast, if the United State takes not new actions to curb energy use, CO2 emissions will likely rise 50 percent during that time. A variety of Federal policy initiatives will be required to achieve large reductions in U.S. CO2 emissions. Such policy actions will have to include both regulatory ``push'' and market ``pull'' mechanisms--including performance standards, tax incentive programs, carbon-emission or energy taxes, labeling and efficiency ratings, and research, development, and demostration activities.

Energy consumption and CO{sub 2} emissions in Iran, 2025

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mirzaei, Maryam

Climate change and global warming as the key human societies' threats are essentially associated with energy consumption and CO{sub 2} emissions. A system dynamic model was developed in this study to model the energy consumption and CO{sub 2} emission trends for Iran over 2000–2025. Energy policy factors are considered in analyzing the impact of different energy consumption factors on environmental quality. The simulation results show that the total energy consumption is predicted to reach 2150 by 2025, while that value in 2010 is 1910, which increased by 4.3% yearly. Accordingly, the total CO{sub 2} emissions in 2025 will reach 985more » million tonnes, which shows about 5% increase yearly. Furthermore, we constructed policy scenarios based on energy intensity reduction. The analysis show that CO{sub 2} emissions will decrease by 12.14% in 2025 compared to 2010 in the scenario of 5% energy intensity reduction, and 17.8% in the 10% energy intensity reduction scenario. The results obtained in this study provide substantial awareness regarding Irans future energy and CO{sub 2} emission outlines. - Highlights: • Creation of an energy consumption model using system dynamics. • The effect of different policies on energy consumption and emission reductions. • An ascending trend for the environmental costs caused by CO{sub 2} emissions is observed. • An urgent need for energy saving and emission reductions in Iran.« less

Emerging Community Noise Reduction Approaches

NASA Technical Reports Server (NTRS)

Envia, Edmane

2012-01-01

An overview of the current NASA research portfolio in the area of aircraft noise reduction is presented. The emphasis of the research described herein is on meeting the aggressive near- and mid-term national goals for reducing aircraft noise emissions, which NASA internal studies have shown to be feasible using noise reduction technologies currently being developed in-house or in partnership with NASA s industry and academic partners. While NASA has an active research effort in airframe noise reduction, this overview focuses on propulsion noise reduction only.

Acoustic-Emission Weld-Penetration Monitor

NASA Technical Reports Server (NTRS)

Maram, J.; Collins, J.

1986-01-01

Weld penetration monitored by detection of high-frequency acoustic emissions produced by advancing weld pool as it melts and solidifies in workpiece. Acoustic emission from TIG butt weld measured with 300-kHz resonant transducer. Rise in emission level coincides with cessation of weld penetration due to sudden reduction in welding current. Such monitoring applied to control of automated and robotic welders.

Control strategies for nitrous oxide emissions reduction on wastewater treatment plants operation.

PubMed

Santín, I; Barbu, M; Pedret, C; Vilanova, R

2017-11-15

The present paper focused on reducing greenhouse gases emissions in wastewater treatment plants operation by application of suitable control strategies. Specifically, the objective is to reduce nitrous oxide emissions during the nitrification process. Incomplete nitrification in the aerobic tanks can lead to an accumulation of nitrite that triggers the nitrous oxide emissions. In order to avoid the peaks of nitrous oxide emissions, this paper proposes a cascade control configuration by manipulating the dissolved oxygen set-points in the aerobic tanks. This control strategy is combined with ammonia cascade control already applied in the literature. This is performed with the objective to take also into account effluent pollutants and operational costs. In addition, other greenhouse gases emissions sources are also evaluated. Results have been obtained by simulation, using a modified version of Benchmark Simulation Model no. 2, which takes into account greenhouse gases emissions. This is called Benchmark Simulation Model no. 2 Gas. The results show that the proposed control strategies are able to reduce by 29.86% of nitrous oxide emissions compared to the default control strategy, while maintaining a satisfactory trade-off between water quality and costs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Greenhouse gas emissions reduction in different economic sectors: Mitigation measures, health co-benefits, knowledge gaps, and policy implications.

PubMed

Gao, Jinghong; Hou, Hongli; Zhai, Yunkai; Woodward, Alistair; Vardoulakis, Sotiris; Kovats, Sari; Wilkinson, Paul; Li, Liping; Song, Xiaoqin; Xu, Lei; Meng, Bohan; Liu, Xiaobo; Wang, Jun; Zhao, Jie; Liu, Qiyong

2018-09-01

To date, greenhouse gas (GHG) emissions, mitigation strategies and the accompanying health co-benefits in different economic sectors have not been fully investigated. The purpose of this paper is to review comprehensively the evidence on GHG mitigation measures and the related health co-benefits, identify knowledge gaps, and provide recommendations to promote further development and implementation of climate change response policies. Evidence on GHG emissions, abatement measures and related health co-benefits has been observed at regional, national and global levels, involving both low- and high-income societies. GHG mitigation actions have mainly been taken in five sectors: energy generation, transport, food and agriculture, household and industry, consistent with the main sources of GHG emissions. GHGs and air pollutants to a large extent stem from the same sources and are inseparable in terms of their atmospheric evolution and effects on ecosystem; thus, GHG reductions are usually, although not always, estimated to have cost effective co-benefits for public health. Some integrated mitigation strategies involving multiple sectors, which tend to create greater health benefits. The pros and cons of different mitigation measures, issues with existing knowledge, priorities for research, and potential policy implications were also discussed. Findings from this study can play a role not only in motivating large GHG emitters to make decisive changes in GHG emissions, but also in facilitating cooperation at international, national and regional levels, to promote GHG mitigation policies that protect public health from climate change and air pollution simultaneously. Copyright © 2018 Elsevier Ltd. All rights reserved.

Reduction of PM emissions from specific sources reflected on key components concentrations of ambient PM10

NASA Astrophysics Data System (ADS)

Minguillon, M. C.; Querol, X.; Monfort, E.; Alastuey, A.; Escrig, A.; Celades, I.; Miro, J. V.

2009-04-01

The relationship between specific particulate emission control and ambient levels of some PM10 components (Zn, As, Pb, Cs, Tl) was evaluated. To this end, the industrial area of Castellón (Eastern Spain) was selected, where around 40% of the EU glazed ceramic tiles and a high proportion of EU ceramic frits (middle product for the manufacture of ceramic glaze) are produced. The PM10 emissions from the ceramic processes were calculated over the period 2000 to 2007 taking into account the degree of implementation of corrective measures throughout the study period. Abatement systems (mainly bag filters) were implemented in the majority of the fusion kilns for frit manufacture in the area as a result of the application of the Directive 1996/61/CE, leading to a marked decrease in PM10 emissions. On the other hand, ambient PM10 sampling was carried out from April 2002 to July 2008 at three urban sites and one suburban site of the area and a complete chemical analysis was made for about 35 % of the collected samples, by means of different techniques (ICP-AES, ICP-MS, Ion Chromatography, selective electrode and elemental analyser). The series of chemical composition of PM10 allowed us to apply a source contribution model (Principal Component Analysis), followed by a multilinear regression analysis, so that PM10 sources were identified and their contribution to bulk ambient PM10 was quantified on a daily basis, as well as the contribution to bulk ambient concentrations of the identified key components (Zn, As, Pb, Cs, Tl). The contribution of the sources identified as the manufacture and use of ceramic glaze components, including the manufacture of ceramic frits, accounted for more than 65, 75, 58, 53, and 53% of ambient Zn, As, Pb, Cs and Tl levels, respectively (with the exception of Tl contribution at one of the sites). The important emission reductions of these sources during the study period had an impact on ambient key components levels, such that there was a high

NASA Glenn High Pressure Low NOx Emissions Research

NASA Technical Reports Server (NTRS)

Tacina, Kathleen M.; Wey, Changlie

2008-01-01

In collaboration with U.S. aircraft engine companies, NASA Glenn Research Center has contributed to the advancement of low emissions combustion systems. For the High Speed Research Program (HSR), a 90% reduction in nitrogen oxides (NOx) emissions (relative to the then-current state of the art) has been demonstrated in sector rig testing at General Electric Aircraft Engines (GEAE). For the Advanced Subsonic Technology Program (AST), a 50% reduction in NOx emissions relative to the 1996 International Civil Aviation Organization (ICAO) standards has been demonstrated in sector rigs at both GEAE and Pratt & Whitney (P&W). During the Ultra Efficient Engine Technology Program (UEET), a 70% reduction in NOx emissions, relative to the 1996 ICAO standards, was achieved in sector rig testing at Glenn in the world class Advanced Subsonic Combustion Rig (ASCR) and at contractor facilities. Low NOx combustor development continues under the Fundamental Aeronautics Program. To achieve these reductions, experimental and analytical research has been conducted to advance the understanding of emissions formation in combustion processes. Lean direct injection (LDI) concept development uses advanced laser-based non-intrusive diagnostics and analytical work to complement the emissions measurements and to provide guidance for concept improvement. This paper describes emissions results from flametube tests of a 9-injection-point LDI fuel/air mixer tested at inlet pressures up to 5500 kPa. Sample results from CFD and laser diagnostics are also discussed.

Emission Abatement System

DOEpatents

Bromberg, Leslie; Cohn, Daniel R.; Rabinovich, Alexander

2003-05-13

Emission abatement system. The system includes a source of emissions and a catalyst for receiving the emissions. Suitable catalysts are absorber catalysts and selective catalytic reduction catalysts. A plasma fuel converter generates a reducing gas from a fuel source and is connected to deliver the reducing gas into contact with the absorber catalyst for regenerating the catalyst. A preferred reducing gas is a hydrogen rich gas and a preferred plasma fuel converter is a plasmatron. It is also preferred that the absorber catalyst be adapted for absorbing NO.sub.x.

Universal health coverage from multiple perspectives: a synthesis of conceptual literature and global debates.

PubMed

Abiiro, Gilbert Abotisem; De Allegri, Manuela

2015-07-04

There is an emerging global consensus on the importance of universal health coverage (UHC), but no unanimity on the conceptual definition and scope of UHC, whether UHC is achievable or not, how to move towards it, common indicators for measuring its progress, and its long-term sustainability. This has resulted in various interpretations of the concept, emanating from different disciplinary perspectives. This paper discusses the various dimensions of UHC emerging from these interpretations and argues for the need to pay attention to the complex interactions across the various components of a health system in the pursuit of UHC as a legal human rights issue. The literature presents UHC as a multi-dimensional concept, operationalized in terms of universal population coverage, universal financial protection, and universal access to quality health care, anchored on the basis of health care as an international legal obligation grounded in international human rights laws. As a legal concept, UHC implies the existence of a legal framework that mandates national governments to provide health care to all residents while compelling the international community to support poor nations in implementing this right. As a humanitarian social concept, UHC aims at achieving universal population coverage by enrolling all residents into health-related social security systems and securing equitable entitlements to the benefits from the health system for all. As a health economics concept, UHC guarantees financial protection by providing a shield against the catastrophic and impoverishing consequences of out-of-pocket expenditure, through the implementation of pooled prepaid financing systems. As a public health concept, UHC has attracted several controversies regarding which services should be covered: comprehensive services vs. minimum basic package, and priority disease-specific interventions vs. primary health care. As a multi-dimensional concept, grounded in international human

Research to Support California Greenhouse Gas Reduction Programs

NASA Astrophysics Data System (ADS)

Croes, B. E.; Charrier-Klobas, J. G.; Chen, Y.; Duren, R. M.; Falk, M.; Franco, G.; Gallagher, G.; Huang, A.; Kuwayama, T.; Motallebi, N.; Vijayan, A.; Whetstone, J. R.

2016-12-01

Since the passage of the California Global Warming Solutions Act in 2006, California state agencies have developed comprehensive programs to reduce both long-lived and short-lived climate pollutants. California is already close to achieving its goal of reducing greenhouse (GHG) emissions to 1990 levels by 2020, about a 30% reduction from business as usual. In addition, California has developed strategies to reduce GHG emissions another 40% by 2030, which will put the State on a path to meeting its 2050 goal of an 80% reduction. To support these emission reduction goals, the California Air Resources Board (CARB) and the California Energy Commission have partnered with NASA's Carbon Monitoring System (CMS) program on a comprehensive research program to identify and quantify the various GHG emission source sectors in the state. These include California-specific emission studies and inventories for carbon dioxide (CO2), methane (CH4), and nitrous oxide (N2O) emission sources; a Statewide GHG Monitoring Network for these pollutants integrated with the Los Angeles Megacities Carbon Project funded by several federal agencies; efforts to verify emission inventories using inversion modeling and other techniques; mobile measurement platforms and flux chambers to measure local and source-specific emissions; and a large-scale statewide methane survey using a tiered monitoring and measurement program, which will include satellite, airborne, and ground-level measurements of the various regions and source sectors in the State. In addition, there are parallel activities focused on black carbon (BC) and fluorinated gases (F-gases) by CARB. This presentation will provide an overview of results from inventory, monitoring, data analysis, and other research efforts on Statewide, regional, and local sources of GHG emissions in California.

Catalysts for cleaner combustion of coal, wood and briquettes sulfur dioxide reduction options for low emission sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, P.V.

1995-12-31

Coal fired, low emission sources are a major factor in the air quality problems facing eastern European cities. These sources include: stoker-fired boilers which feed district heating systems and also meet local industrial steam demand, hand-fired boilers which provide heat for one building or a small group of buildings, and masonary tile stoves which heat individual rooms. Global Environmental Systems is marketing through Global Environmental Systems of Polane, Inc. catalysts to improve the combustion of coal, wood or fuel oils in these combustion systems. PCCL-II Combustion Catalysts promotes more complete combustion, reduces or eliminates slag formations, soot, corrosion and somemore » air pollution emissions and is especially effective on high sulfur-high vanadium residual oils. Glo-Klen is a semi-dry powder continuous acting catalyst that is injected directly into the furnace of boilers by operating personnel. It is a multi-purpose catalyst that is a furnace combustion catalyst that saves fuel by increasing combustion efficiency, a cleaner of heat transfer surfaces that saves additional fuel by increasing the absorption of heat, a corrosion-inhibiting catalyst that reduces costly corrosion damage and an air pollution reducing catalyst that reduces air pollution type stack emissions. The reduction of sulfur dioxides from coal or oil-fired boilers of the hand fired stoker design and larger, can be controlled by the induction of the Glo-Klen combustion catalyst and either hydrated lime or pulverized limestone.« less

Setting priorities to address cardiovascular diseases through universal health coverage in low- and middle-income countries.

PubMed

Watkins, David A; Nugent, Rachel A

2017-01-01

Over the past decade, universal health coverage (UHC) has emerged as a major policy goal for many low- and middle-income country governments. Yet, despite the high burden of cardiovascular diseases (CVD), relatively little is known about how to address CVD through UHC. This review covers three major topics. First, we define UHC and provide some context for its importance, and then we illustrate its relevance to CVD prevention and treatment. Second, we discuss how countries might select high-priority CVD interventions for a UHC health benefits package drawing on economic evaluation methods. Third, we explore some implementation challenges and identify research gaps that, if addressed, could improve the inclusion of CVD into UHC.

Measuring Greenhouse Gas Emissions and Sinks Across California Land Cover

NASA Astrophysics Data System (ADS)

Fischer, M. L.

2017-12-01

Significant reductions in greenhouse gas (GHG) emissions are needed to limit rising planetary temperatures that will otherwise limit Earth's capacity to support life, introducing geopolitical instability. To help mitigate this threat, California has legislated landmark reductions in state-level greenhouse gas (GHG) emissions that set an example for broader action. Beginning with relatively assured reduction of current emissions to 1990 levels by 2020, future goals are much more challenging with 40% and 80% reductions below 1990 emissions by 2030 and 2050, respectively. While the majority of the reductions must focus on fossil fuels, inventory estimates of non-CO2 GHG emissions (i.e., CH4, N2O, and industrial compounds) constitute 15% of the total, suggesting reductions are required across multiple land use sectors. However, recent atmospheric inversion studies show methane and nitrous oxide (CH4 & N2O) emissions exceed current inventory estimates by factors of 1.2-1.8 and 1.6-2.6 (at 95% confidence), respectively, perhaps constituting up to 30% of State total emissions. The discrepancy is likely because current bottom-up models used for inventories do not accurately capture important management or biophysical factors. In the near term, process level experiments and sector-specific inversions are being planned to quantify the factors controlling non-CO2 GHG emissions for several of the dominant emission sectors. For biosphere carbon, California forests lands, which also depend on the combination of management, climate, and weather, lost above ground carbon from 2001-2010, and may be expected to lose soil and root carbon as a longer-term result. Here, it is important to identify and apply the best principles in forestry and agriculture to increase carbon stocks in depleted forest and agricultural areas, focusing on approaches that provide resilience to future climate and weather variations. Taken together, improved atmospheric, plant, and soil observations, together