Lifespan estimation of seal welded super stainless steels for water condenser of nuclear power plants

NASA Astrophysics Data System (ADS)

Kim, Young Sik; Park, Sujin; Chang, Hyun Young

2014-01-01

When sea water was used as cooling water for water condenser of nuclear power plants, commercial stainless steels can not be applied because chloride concentration exceeds 20,000 ppm. There are many opinions for the materials selection of tube and tube sheets of a condenser. This work reviewed the application guide line of stainless steels for sea-water facilities and the estimation equations of lifespan were proposed from the analyses of both field data for sea water condenser and experimental results of corrosion. Empirical equations for lifespan estimation were derived from the pit initiation time and re-tubing time of stainless steel tubing in sea water condenser of nuclear power plants. The lifespan of seal-welded super austenitic stainless steel tube/tube sheet was calculated from these equations. Critical pitting temperature of seal-welded PRE 50 grade super stainless steel was evaluated as 60 °C. Using the proposed equation in engineering aspect, tube pitting corrosion time of seal-welded tube/tube sheet was calculated as 69.8 years and re-tubing time was estimated as 82.0 years.

Assessment of the local role of a steel making plant by POPs deposition measurements.

PubMed

Rada, E C; Ragazzi, M; Schiavon, M

2014-09-01

Atmospheric depositions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polychlorinated biphenyls (PCBs) were monitored at three sites in the vicinity of a steel making plant, located in an Italian alpine valley. A high variability in the deposition of PCDD/Fs was observed. The influence of the plant was noticeable at two of the sampling sites. However, as the congener profiles demonstrated, wood burning for domestic heating is an additional source of PCDD/Fs for the area under investigation, and this interferes with the characterization of the emissions from the steel plant. The influence of the plant, in terms of PCDD/F deposition, was not noticeable at the most distant site (2km), where an extremely high peak of PCDD/F deposition was measured during the period from 12 January-22 February 2012. The comparison between the congener distribution of PCDD/Fs observed in this sample and the fingerprints of different sources could justify the attribution of this anomalous peak to a possible episode of domestic waste combustion. In order to find a better correlation between the deposition to soil and emissions from the plant, the congener distribution of PCBs was studied. The PCB profiles observed at the three sites well reproduced the average profile found in samples of ash retained by the bag filter of the plant. Thus the monitoring of PCB deposition is an interesting starting point to calibrate dispersion models to assess the impact of steel making activities. Copyright © 2014 Elsevier Ltd. All rights reserved.

Atmospheric CO2 sequestration in iron and steel slag: Consett, Co. Durham, UK.

PubMed

Mayes, William Matthew; Riley, Alex L; Gomes, Helena I; Brabham, Peter; Hamlyn, Joanna; Pullin, Huw; Renforth, Phil

2018-06-12

Carbonate formation in waste from the steel industry could constitute a non-trivial proportion of global requirements to remove carbon dioxide from the atmosphere at potentially low cost. To constrain this potential, we examined atmospheric carbon dioxide sequestration in a >20 million tonne legacy slag deposit in northern England, UK. Carbonates formed from the drainage water of the heap had stable carbon and oxygen isotopes between -12 and -25 ‰ and -5 and -18 ‰ for δ13C and δ18O respectively, suggesting atmospheric carbon dioxide sequestration in high pH solutions. From analysis of solution saturation state, we estimate that between 280 and 2,900 tCO2 have precipitated from the drainage waters. However, by combining a thirty-seven-year dataset of the drainage water chemistry with geospatial analysis, we estimate that <1 % of the maximum carbon capture potential of the deposit may have been realised. This implies that uncontrolled deposition of slag is insufficient to maximise carbon sequestration, and there may be considerable quantities of unreacted legacy deposits available for atmospheric carbon sequestration.

Exposure to air pollution near a steel plant and effects on cardiovascular physiology: a randomized crossover study.

PubMed

Liu, Ling; Kauri, Lisa Marie; Mahmud, Mamun; Weichenthal, Scott; Cakmak, Sabit; Shutt, Robin; You, Hongyu; Thomson, Errol; Vincent, Renaud; Kumarathasan, Premkumari; Broad, Gayle; Dales, Robert

2014-03-01

Iron and steel industry is an important source of air pollution emissions. Few studies have investigated cardiovascular effects of air pollutants emitted from steel plants. We examined the influence of outdoor air pollution in the vicinity of a steel plant on cardiovascular physiology in Sault Ste. Marie, Canada. Sixty-one healthy, non-smoking subjects (females/males=33/28, median age 22 years) spent 5 consecutive 8-hour days outdoors in a residential area neighbouring a steel plant, or on a college campus approximately 5 kilometres away from the plant, and then crossed over to the other site with a 9-day washout. Mid day, subjects underwent daily 30-minute moderate intensity exercise. Blood pressure (BP) and pulse rate were determined daily and post exercise at both sites. Flow-mediated vasodilation (FMD) was determined at the site near the plant. Air pollution was monitored at both sites. Mixed-effects regressions were run for statistical associations, adjusting for weather variables. Concentrations of ultrafine particles, sulphur dioxide (SO2), nitrogen dioxide (NO2) and carbon monoxide (CO) were 50-100% higher at the site near the plant than at the college site, with minor differences in temperature, humidity, and concentrations of particulate matter ≤2.5 μm in size (PM2.5) and ozone (O3). Resting pulse rate [mean (95% confidence interval)] was moderately higher near the steel plant [+1.53 bpm (0.31, 2.78)] than at the college site, male subjects having the highest pulse rate elevation [+2.77 bpm (0.78, 4.76)]. Resting systolic and diastolic BP and pulse pressure, and post-exercise BP and pulse rate were not significantly different between two sites. Interquartile range concentrations of SO2 (2.9 ppb), NO2 (5.0 ppb) and CO (0.2 ppm) were associated with increased pulse rate [0.19 bpm (-0.00, 0.38), 0.86 bpm (0.03, 1.68), and 0.11 bpm (0.00, 0.22), respectively], ultrafine particles (10,256 count/cm(3)) associated with increased pulse pressure [0.85 mmHg (0

Improved wastewater treatment at Wheeling-Pittsburgh Steel Corporations`s Steubenville East Coke Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goshe, A.J.; Nodianos, M.J.

1995-12-01

Wheeling-Pittsburgh Steel Corporation recently improved its wastewater treatment at it`s by-products coke plant. This has led to greatly improved effluent quality. Excess ammonia liquor, along with wastewater from the light oil recovery plant, desulfurization facility, and coal pile runoff, must be treated prior to being discharged into the Ohio River. This is accomplished using a biological wastewater treatment plant to remove 99.99% of the organic contaminants and ammonia. Biologically treated, clarified wastewater is now polished in the newly constructed tertiary treatment plant.

Heavy metal contamination and ecological risk of farmland soils adjoining steel plants in Tangshan, Hebei, China.

PubMed

Yang, Liyun; Yang, Maomao; Wang, Liping; Peng, Fei; Li, Yuan; Bai, Hao

2018-01-01

The purpose of this study was to determine the heavy metal concentrations and ecological risks to farmland soils caused by atmospheric deposition adjoining five industrial steel districts in Tangshan, Hebei, China. A total of 39 topsoil samples from adjoining these plants were collected and analyzed for Pb, Zn, Cu, Cr, and As. The geo-accumulation index (Igeo) and potential ecological risk index (PERI) were calculated to assess the heavy metal pollution level in soils. The results showed that the levels of Pb and As in farmland soils adjoining all steel plants were more than the background value, with the As content being excessively high. The Cr and Cu contents of some samples were over the background values, but the Zn content was not. In all the research areas, the largest Igeo value of the heavy metals was for As, followed by Pb, and the largest monomial PERI ([Formula: see text]) was As, which showed that the pollution of As in farmland soils was significant and had considerable ecological risk. Additionally, the heavy metal sequential extraction experiments showed that Pb and Cr, which exceeded the background value, were present in about 20% of the exchangeable and carbonate-bound fractions in the soils surrounding some steel plants. This would imply the risk of these heavy metals being absorbed and accumulated by the crops. Therefore, the local government needs to control the pollution of heavy metals in the farmland soils adjoining the steel plant as soon as possible, in order to avoid possible ecological and food safety risks.

New pressure control method of mixed gas in a combined cycle power plant of a steel mill

NASA Astrophysics Data System (ADS)

Xie, Yudong; Wang, Yong

2017-08-01

The enterprise production concept is changing with the development of society. A steel mill requires a combined-cycle power plant, which consists of both a gas turbine and steam turbine. It can recycle energy from the gases that are emitted from coke ovens and blast furnaces during steel production. This plant can decrease the overall energy consumption of the steel mill and reduce pollution to our living environment. To develop a combined-cycle power plant, the pressure in the mixed-gas transmission system must be controlled in the range of 2.30-2.40 MPa. The particularity of the combined-cycle power plant poses a challenge to conventional controllers. In this paper, a composite control method based on the Smith predictor and cascade control was proposed for the pressure control of the mixed gases. This method has a concise structure and can be easily implemented in actual industrial fields. The experiment has been conducted to validate the proposed control method. The experiment illustrates that the proposed method can suppress various disturbances in the gas transmission control system and sustain the pressure of the gas at the desired level, which helps to avoid abnormal shutdowns in the combined-cycle power plant.

Water requirements of the iron and steel industry

USGS Publications Warehouse

Walling, Faulkner B.; Otts, Louis Ethelbert

1967-01-01

Twenty-nine steel plants surveyed during 1957 and 1958 withdrew from various sources about 1,400 billion gallons of water annually and produced 40.8 million tons of ingot steel. This is equivalent to about 34,000 gallons of water per ton of steel. Fifteen iron ore mines and fifteen ore concentration plants together withdrew annually about 89,000 million gallons to produce 15 million tons of iron ore concentrate, or 5,900 gallons per ton of concentrate. About 97 percent of the water used in the steel plants came from surface sources, 2.2 percent was reclaimed sewage, and 1.2 percent was ground water. Steel plants supplied about 96 percent of their own water requirements, although only three plants used self-supplied water exclusively. Water used by the iron ore mines and concentration plants was also predominantly self supplied from surface source. Water use in the iron and steel industry varied widely and depended on the availability of water, age and condition of plants and equipment, kinds of processes, and plant operating procedures. Gross water use in integrated steel plants ranged from 11,200 to 110,000 gallons per ton of steel ingots, and in steel processing plants it ranged from 4,180 to 26,700 gallons per ton. Water reuse also varied widely from 0 to 18 times in integrated steel plants and from 0 to 44 times in steel processing plants. Availability of water seemed to be the principal factor in determining the rate of reuse. Of the units within steel plants, a typical (median) blast furnace required 20,500 gallons of water per ton of pig iron. At the 1956-60 average rate of pig iron consumption, this amounts to about 13,000 gallons per ton of steel ingots or about 40 percent of that required by a typical integrated steel plant 33,200 gallons per ton. Different processes of iron ore concentration are devised specifically for the various kinds of ore. These processes result in a wide range of water use from 124 to 11,300 gallons of water per ton of iron ore

Occupational asthma in a steel coating plant.

PubMed

Venables, K M; Dally, M B; Burge, P S; Pickering, C A; Newman Taylor, A J

1985-08-01

An outbreak of occupational asthma, of unknown cause and extent, was detected in a steel coating plant. In 1979 a cross-sectional study which defined occupational asthma in terms of respiratory symptoms detected 21 people with suggestive symptoms among the 221 studied. They all worked in the coating shop, but the plastic coatings used at the plant contained many potential sensitising agents that might have caused the asthma. All 21 developed their symptoms after 1971, and it was found that in this year a supplier had modified a coating allowing, at the temperatures used in the process, toluene di-isocyanate to be liberated. Two of the symptomatic subjects were tested by inhalation of the isocyanate and showed asthmatic reactions and other subjects were found to have asthma related to periods spent at work by records of peak expiratory flow rate. Over half the 21 had a symptom free latent period after first exposure of three years or less, a pattern not seen in other subjects with respiratory symptoms. After the isocyanate had been removed from the process 17 of these subjects became asymptomatic or improved, a greater proportion than in other subjects with respiratory symptoms.

Ceramic tiles with black pigment made from stainless steel plant dust: Physical properties and long-term leaching behavior of heavy metals.

PubMed

Zhu, Renbo; Ma, Guojun; Cai, Yongsheng; Chen, Yuxiang; Yang, Tong; Duan, Boyu; Xue, Zhengliang

2016-04-01

Stainless steel plant dust is a hazardous by-product of the stainless steelmaking industry. It contains large amounts of Fe, Cr, and Ni, and can be potentially recycled as a raw material of inorganic black pigment in the ceramic industry to reduce environmental contamination and produce value-added products. In this paper, ceramic tiles prepared with black pigment through recycling of stainless steel plant dust were characterized in terms of physical properties, such as bulk density, water absorption, apparent porosity, and volume shrinkage ratio, as well as the long-term leaching behavior of heavy metals (Cr, Ni, Pb, Cd, and Zn). The results show that good physical properties of ceramic tiles can be obtained with 8% pigments addition, sample preparation pressure of 25 MPa, and sintering at 1200 ºC for 30 min. The major controlling leaching mechanism for Cr and Pb from the ceramic tiles is initial surface wash-off, while the leaching behavior of Cd, Ni, and Zn from the stabilized product is mainly controlled by matrix diffusion. The reutilization process is safe and effective to immobilize the heavy metals in the stainless steel plant dust. Stainless steel plant dust is considered as a hazardous material, and it can be potentially recycled for black pigment preparation in the ceramic industry. This paper provides the characteristics of the ceramic tiles with black pigment through recycling stainless steel plant dust, and the long-term leaching behavior and controlling leaching mechanisms of heavy metals from the ceramic tile. The effectiveness of the treatment process is also evaluated.

A preliminary analysis of incident investigation reports of an integrated steel plant: some reflection.

PubMed

Verma, A; Maiti, J; Gaikwad, V N

2018-06-01

Large integrated steel plants employ an effective safety management system and gather a significant amount of safety-related data. This research intends to explore and visualize the rich database to find out the key factors responsible for the occurrences of incidents. The study was carried out on the data in the form of investigation reports collected from a steel plant in India. The data were processed and analysed using some of the quality management tools like Pareto chart, control chart, Ishikawa diagram, etc. Analyses showed that causes of incidents differ depending on the activities performed in a department. For example, fire/explosion and process-related incidents are more common in the departments associated with coke-making and blast furnace. Similar kind of factors were obtained, and recommendations were provided for their mitigation. Finally, the limitations of the study were discussed, and the scope of the research works was identified.

An intensive monitoring campaign of PAHs for assessing the impact of a steel plant.

PubMed

Di Gilio, A; Ventrella, G; Giungato, P; Tutino, M; Giua, R; Assennato, G; de Gennaro, G

2017-02-01

This study provided a useful approach for assessing the impact of industrial sources on surrounding, especially in a sensitive industrial area as Taranto (South of Italy). Taranto is one of the most industrialized Italian towns, where several emission sources operate simultaneously in proximity to the urban settlement. An intensive monitoring campaign of PAHs was carried out from January 28th to July 30th, 2011, in seven sites located in residential settlement around the industrial area and in the city center. The collected data were integrated with the information about wind direction and speed by means bivariate polarplot in order to characterize and localize the industrial sources. High BaP concentrations were detected especially when Benzene to Toluene ratio (B/T ratio) values excedeed 1 and all receptor sites were downwind to the steel plant. Moreover, in order to discriminate among PAH sources and quantify their contributions, a source apportionment analysis of the collected data was provided by means Principal component Analysis (PCA) and Positive Matrix Factorization (PMF) methods. Finally, the processing of PMF5.0 output by bivariate polar plot, confirmed the impact of steel plant on both industrial sites downwind the steel plant and the city center. B[a]P apportionment was quite similar for industrial and urban sites: the traffic source contributed only 11% and 24% to B[a]P measured at two sites, respectively. Therefore, the proximity of Taranto downtown to industrial pole makes negligible all other source contributions to PAH concentrations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Lung Cancer Risk and Past Exposure to Emissions from a Large Steel Plant

PubMed Central

Ameling, Caroline; van de Kassteele, Jan; Lijzen, Johannes; Oosterlee, Arie; Keuken, Rinske; Visser, Otto; van Wiechen, Carla

2013-01-01

We studied the spatial distribution of cancer incidence rates around a large steel plant and its association with historical exposure. The study population was close to 600,000. The incidence data was collected for 1995–2006. From historical emission data the air pollution concentrations for polycyclic aromatic hydrocarbons (PAH) and metals were modelled. Data were analyzed using Bayesian hierarchical Poisson regression models. The standardized incidence ratio (SIR) for lung cancer was up to 40% higher than average in postcodes located in two municipalities adjacent to the industrial area. Increased incidence rates could partly be explained by differences in socioeconomic status (SES). In the highest exposure category (approximately 45,000 inhabitants) a statistically significant increased relative risk (RR) of 1.21 (1.01–1.43) was found after adjustment for SES. The elevated RRs were similar for men and women. Additional analyses in a subsample of the population with personal smoking data from a recent survey suggested that the observed association between lung cancer and plant emission, after adjustment for SES, could still be caused by residual confounding. Therefore, we cannot indisputably conclude that past emissions from the steel plant have contributed to the increased risk of lung cancer. PMID:24324501

Utilization of structural steel in buildings.

PubMed

Moynihan, Muiris C; Allwood, Julian M

2014-08-08

Over one-quarter of steel produced annually is used in the construction of buildings. Making this steel causes carbon dioxide emissions, which climate change experts recommend be reduced by half in the next 37 years. One option to achieve this is to design and build more efficiently, still delivering the same service from buildings but using less steel to do so. To estimate how much steel could be saved from this option, 23 steel-framed building designs are studied, sourced from leading UK engineering firms. The utilization of each beam is found and buildings are analysed to find patterns. The results for over 10 000 beams show that average utilization is below 50% of their capacity. The primary reason for this low value is 'rationalization'-providing extra material to reduce labour costs. By designing for minimum material rather than minimum cost, steel use in buildings could be drastically reduced, leading to an equivalent reduction in 'embodied' carbon emissions.

Utilization of structural steel in buildings

PubMed Central

Moynihan, Muiris C.; Allwood, Julian M.

2014-01-01

Over one-quarter of steel produced annually is used in the construction of buildings. Making this steel causes carbon dioxide emissions, which climate change experts recommend be reduced by half in the next 37 years. One option to achieve this is to design and build more efficiently, still delivering the same service from buildings but using less steel to do so. To estimate how much steel could be saved from this option, 23 steel-framed building designs are studied, sourced from leading UK engineering firms. The utilization of each beam is found and buildings are analysed to find patterns. The results for over 10 000 beams show that average utilization is below 50% of their capacity. The primary reason for this low value is ‘rationalization’—providing extra material to reduce labour costs. By designing for minimum material rather than minimum cost, steel use in buildings could be drastically reduced, leading to an equivalent reduction in ‘embodied’ carbon emissions. PMID:25104911

New UK nickel-plated steel coins constitute an increased allergy and eczema risk.

PubMed

Julander, Anneli; Midander, Klara; Herting, Gunilla; Thyssen, Jacob P; White, Ian R; Odnevall Wallinder, Inger; Lidén, Carola

2013-06-01

Nickel-plated steel coins have recently been introduced in the United Kingdom. To compare the performance and allergy risk of the new nickel-plated coins (five and ten pence) with those of the cupro-nickel coins being replaced. Coin handling studies with assessment of skin exposure and metal release in artificial sweat were performed. Six volunteers participated. The amount of nickel deposited onto skin during the handling of nickel-plated coins for 1 hr was 7.5 µg/cm(2) , four times higher than that from cupro-nickel coins. The nickel content in the oxidized surface of nickel-plated coins was higher, explaining the higher skin dose. Initial nickel release rates were 10-27 times higher than 1-week rates, emphasizing that brief and repeated contact results in significant nickel exposure. Nickel-plated coins deposit higher levels of nickel onto skin than cupro-nickel coins, and hence pose an increased allergy risk. One-week release in artificial sweat is not suitable for determining the risk of handling items with high nickel release that come into short, repeated contact with the skin. The nickel skin dose is recommended for risk assessment. UK citizens are now, because of this change in coinage, unnecessarily exposed to higher levels of nickel on the skin. This is of public health concern. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Effect of Silicon on the Desulfurization of Al-Killed Steels: Part II. Experimental Results and Plant Trials

NASA Astrophysics Data System (ADS)

Roy, Debdutta; Pistorius, Petrus Christiaan; Fruehan, Richard J.

2013-10-01

Recent observations suggest that increased silicon levels improve ladle desulfurization of aluminum-killed steel. A kinetic model was developed and presented in part I of this paper, demonstrating that increased silicon levels in steel suppress the consumption of aluminum by parasitic reactions like silica reduction and FeO/MnO reduction, thus making more aluminum available at the interface for desulfurization. The results are increases in the rate and the extent of desulfurization. Predictions were compared with laboratory induction furnace melts using 1 kg of steel and 0.1 kg slag. The experimental results demonstrate the beneficial effect of silicon on the desulfurization reaction and that alumina can be reduced out of the slag and aluminum picked up by the steel, if the silicon content in the steel is high enough. The experimental results are in close agreement with the model predictions. Plant trials also show that with increased silicon content, both the rate and extent of desulfurization increase; incorporating silicon early into the ladle desulfurization process leads to considerable savings in aluminum consumption.

Great Lakes Steel -- PCI facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eichinger, F.T.; Dake, S.H.; Wagner, E.D.

1997-12-31

This paper discusses the planning, design, and start-up of the 90 tph PCI facility for National Steel`s Great Lakes Steel Division in River Rouge, MI. This project is owned and operated by Edison Energy Services, and was implemented on a fast-track basis by Raytheon Engineers and Constructors, Babcock Material Handling, and Babcock and Wilcox. This paper presents important process issues, basic design criteria, an the challenges of engineering and building a state-of-the-art PCI facility in two existing plants. Pulverized coal is prepared at the River Rouge Power Plant of Detroit Edison, is pneumatically conveyed 6,000 feet to a storage silomore » at Great Lakes Steel, and is injected into three blast furnaces.« less

A Modified HR3C Austenitic Heat-Resistant Steel for Ultra-supercritical Power Plants Applications Beyond 650 °C

NASA Astrophysics Data System (ADS)

Zhu, C. Z.; Yuan, Y.; Zhang, P.; Yang, Z.; Zhou, Y. L.; Huang, J. Y.; Yin, H. F.; Dang, Y. Y.; Zhao, X. B.; Lu, J. T.; Yan, J. B.; You, C. Y.

2018-02-01

A modified HR3C austenitic steel has been designed by optimizing the chemical composition. Compared with a commercial HR3C alloy, the modified steel has comparable oxidation resistance, yield strength, and plasticity, but higher creep rupture strength and impact toughness after long-term thermal exposure. The results suggest that the modified alloy is a promising candidate for the applications of ultra-supercritical power plants operating beyond 650 °C.

Fact Sheet - Final Air Toxics Rule for Steel Pickling and HCI Process Facilities and Hydrochloric Acid Regeneration Plants

EPA Pesticide Factsheets

Fact Sheet summarizing the main points of the national emssions standard for hazaradous air pollutants (NESHAP) for Steel Pickling— HCl Process Facilities and Hydrochloric Acid Regeneration Plants as promulgated on June 22, 1999.

Experiments on rehabilitation of radioactive metallic waste (RMW) of reactor stainless steels of Siberian chemical plant

NASA Astrophysics Data System (ADS)

Kolpakov, G. N.; Zakusilov, V. V.; Demyanenko, N. V.; Mishin, A. S.

2016-06-01

Stainless steel pipes, used to cool a reactor plant, have a high cost, and after taking a reactor out of service they must be buried together with other radioactive waste. Therefore, the relevant problem is the rinse of pipes from contamination, followed by returning to operation.

Studies to overcome the manufacturing problems in blast furnace tap hole clay of Integrated Steel Plants: Experimental approach

NASA Astrophysics Data System (ADS)

Siva kumar, R.; Mohammed, Raffi; Srinivasa Rao, K.

2018-03-01

Integrated Steel Plants commonly uses Blast Furnace route for iron production which accounts for over 60 % of the world iron output. Blast Furnace runs for ten to twenty years without repairing hearth walls and Tap Hole (TH). Tap hole is an outlet for hot metal produced in a Blast Furnace and run from the shell of the furnace into the interior allowing access to the molten material. Tapping is the term used for drilling a hole through the tap hole which allows the molten iron and slag to flow out. In Iron making process, removal of liquid iron from furnace and sending it for steel making is known as cast house practice. For tapping liquid iron and operating the tap hole requires a special type of clay. Tap hole clay (THC) used to stop the flow of liquid iron and slag from the blast furnace. Present work deals with the study on manufacturing of THC at Visakhapatnam Steel Plant and problems related to manufacturing. Experiments were conducted to solve the identified problems and results are furnished in detail. The findings can improve the manufacturing process and improve the productivity of tap hole clay.

Life after Steel

ERIC Educational Resources Information Center

Mangan, Katherine

2013-01-01

Bobby Curran grew up in a working-class neighborhood in Baltimore, finished high school, and followed his grandfather's steel-toed bootprints straight to Sparrows Point, a 3,000-acre sprawl of industry on the Chesapeake Bay. College was not part of the plan. A gritty but well-paying job at the RG Steel plant was Mr. Curran's ticket to a secure…

DNA barcoding for biosecurity: case studies from the UK plant protection program.

PubMed

Hodgetts, Jennifer; Ostojá-Starzewski, Jozef C; Prior, Thomas; Lawson, Rebecca; Hall, Jayne; Boonham, Neil

2016-11-01

Since its conception, DNA barcoding has seen a rapid uptake within the research community. Nevertheless, as with many new scientific tools, progression towards the point of routine deployment within diagnostic laboratories has been slow. In this paper, we discuss the application of DNA barcoding in the Defra plant health diagnostic laboratories, where DNA barcoding is used primarily for the identification of invertebrate pests. We present a series of case studies that demonstrate the successful application of DNA barcoding but also reveal some potential limitations to expanded use. The regulated plant pest, Bursephalenchus xylophilus, and one of its vectors, Monochamus alternatus, were found in dining chairs. Some traded wood products are potentially high risk, allowing the movement of longhorn beetles; Trichoferus campestris, Leptura quadrifasciata, and Trichoferus holosericeus were found in a wooden cutlery tray, a railway sleeper, and a dining chair, respectively. An outbreak of Meloidogyne fallax was identified in Allium ampeloprasum and in three weed species. Reference sequences for UK native psyllids were generated to enable the development of rapid diagnostics to be used for monitoring following the release of Aphalara itadori as a biological control agent for Fallopia japonica.

The use of fixed appliances in the UK: a survey of specialist orthodontists.

PubMed

Banks, Phil; Elton, Victoria; Jones, Yvonne; Rice, Peter; Derwent, Serena; Odondi, Lang'o

2010-03-01

To investigate the use of fixed appliances in the UK. Prospective postal questionnaire. UK. All members of the General Dental Council Specialist List in Orthodontics still in active practice and not in training posts. A preemptive letter of explanation was sent inviting orthodontists to participate in the survey. The questionnaire was subsequently posted to 935 specialists. Data analysis investigated differences in clinical practice related to varying provider groups, level of operator experience and geographical region. The response rate achieved was 66.3%. A majority of orthodontists routinely used the 0.022 inch pre-adjusted edgewise system, standard size Siamese pattern stainless steel brackets, conventionally ligated and bonded using standard etch and light cured composite. Nickel titanium and stainless steel were the most popular archwire materials. Anchorage was supported routinely by palatal and lingual arches in up to 25% and by headgear in over a third of respondents. Newer innovations showed variable popularity. Self-etching primer was used routinely by one-third of respondents with 11% use of self-ligating brackets. Banding of first molars was preferred by over 60% of clinicians. Bone screw implants were used by only 0.2% of respondents. Clinicians with less than 10 years experience used more headgear, light curing, MBT prescription and molar bonding. Operators with over 20 years experience used more chemically cured bonding, Roth prescription, banded first molars, 0.018 inch slot size and Tip-Edge(TM), with less use of headgear. Fixed appliance use differed from that reported in the US with lower use in the UK of standard edgewise and Roth systems, aesthetic, miniaturised and 0.018 inch slot brackets and rapid maxillary expansion. Most UK orthodontic specialists routinely used the 0.022 inch pre-adjusted edgewise system with standard size Siamese steel brackets bonded using standard etch and light cured composite with conventional ligation. Variations

Recent Developments in Niobium Containing Austenitic Stainless Steels for Thermal Power Plants

NASA Astrophysics Data System (ADS)

de Oliveira, Mariana Perez; Zhang, Wei; Yu, Hongyao; Bao, Hansheng; Xie, Xishan

The challenge of growing continuously in a sustainable way is the main driver to improve efficiency in the use of natural resources. The increasing demand for energy has made thermal power based countries to set audacious programs to increase efficiency of thermal power generation. In China, coal-burning accounts nowadays for approximately 65% of the total primary energy supply being responsible for around 25% of the countries' CO2 emission, this coal-based energy supply scenario is believed to continue until 2020. Therefore, the country has invested strongly in the last years in the construction of more efficient power plants. To attend higher operating temperatures and steam pressures, the application of higher performance materials is mandatory, presenting improved mechanical resistance — to stand the higher pressures applied — and having sufficient high temperature and corrosion resistance with the best cost-benefit relation possible. The present work addresses some research developments made in niobium containing austenitic stainless steels for super heaters and re-heater tubes in the past years as a joint effort between industry and academia to understand mechanisms and optimize the steel chemical composition, improving its performance. Niobium role has been studied in detail in heat resistant stainless steels TP347H, Super 304 and HR3C, a summary of such studies is presented in this paper. Niobium improves high temperature properties as it precipitates as nano-size MX and NbCrN, well dispersed in the matrix, hindering dislocation movement, increasing precipitation strengthening and creep resistance.

A&M. Demineralization plant (TAN649). Steel door. Ralph M. Parsons 1480L/ANP/GA3649MS1. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Demineralization plant (TAN-649). Steel door. Ralph M. Parsons 1480-L/ANP/GA-3-649-MS-1. Date: October 1958. Approved by INEEL Classification Office for public release. INEEL index code no. 034-0649-40-693-107443 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

[Prevalence and influence factors of hypertension among the workers exposed to noise in steel making and steel rolling workshop of an iron and steel plant].

PubMed

Li, Yanhong; Chen, Guoshun; Yu, Shanfa

2015-05-01

To investigate the prevalence and influence factors of hypertension among the workers exposed to noise in steel making and steel rolling workshop of an iron and steel plant. Using cluster sampling method, 3 150 workers exposed to noise participated in this study. According to do questionnaire survey and blood pressure measurement, 2 924 workers were tested, among which 1 313 workers were from steel making workshop and 1 611 workers were from steel rolling workshop. The relationships between different demographic characteristics, different habits, and different cumulative noise exposures of workers exposed to noise and hypertension were analyzed. For the hypertension prevalence rate, the total prevalence rate was 27.43% (802/2 924), the male was higher than the female (29.88 % (753/2 520) vs 12.13% (49/404), χ² = 55.13, P < 0.001), married ones were higher than the unmarried (29.84% (718/2 406) vs 16.22% (84/518), χ² = 39.76, P < 0.001), the smoking subjects were higher than the no smoking (30.31% (438/1 445) vs 24.61% (364/1 479), χ² = 11.93, P = 0.001), drinking ones were higher than the no drinking (31.53% (541/1 716) vs 21.61% (261/1 208), χ² = 35.05, P < 0.001). The hypertension prevalence rates among the subjects with education background in junior high school and below, high school (secondary) and university and above were separately 44.96%(125/278), 29.95%(455/1 519) and 19.70%(222/1 127) (χ² = 81.65, P < 0.001), among cumulative exposure groups 77-89, 90-94, 95-99, 100-104 and 105-113 were separately 8.43% (14/166), 14.48% (53/366), 24.28% (297/1 223), 36.65% (335/914) and 40.39%(103/255) (χ² = 127.58, P < 0.001). Multivariate logistic regression analysis showed that workers who exposed to cumulative noise in 95-99, 100-104 and 105-113 dB(A) ·year had the higher risk of hypertension, the OR (95%CI) were 1.84 (95% CI: 1.35-2.51), 1.74 (95% CI: 1.24-2.45) and 1.68 (95% CI: 1.09-2.58). Drinking (OR = 1.60, 95% CI: 1.32-1.95) and BMI ≥ 24.0 kg

Corrosion Mechanism of Low-Carbon Steel in Industrial Water and Adsorption Thermodynamics in the Presence of Some Plant Extracts

NASA Astrophysics Data System (ADS)

Badiea, A. M.; Mohana, K. N.

2009-12-01

The effects of radish leaves and black cumin as plant extracts on the corrosion behavior of low-carbon steel in industrial water in the temperature range of 30 to 80 °C and velocity range of 1.44 to 2.02 m s-1 using potentiodynamic polarization, electrochemical impedance spectroscopy, and mass loss measurements have been investigated. The inhibition efficiency increased with increasing concentration of the plant extracts up to a critical value but it slightly decreased with increasing temperature. Inhibition efficiency values obtained from mass loss and potentiodynamic data were in reasonable agreement. Potentiodynamic polarization clearly indicated that radish leaves and black cumin extracts acted as anodic inhibitors. The adsorption behavior was found to obey the Flory-Huggins isotherm model. The associated activation parameters and thermodynamic data of adsorption were evaluated and discussed. The results show that radish leaves and black cumin could serve as effective inhibitors for low-carbon steel in industrial water media, with black cumin providing better protection than radish leaves.

North and west facades of crucible steel building; looking southeast ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

North and west facades of crucible steel building; looking southeast - Bethlehem Steel Corporation, South Bethlehem Works, Crucible Steel Plant, Along Lehigh River, North of Fourth Street, West of Minsi Trail Bridge, Bethlehem, Northampton County, PA

Assessing dust exposure in an integrated iron and steel manufacturing plant in South India.

PubMed

Ravichandran, B; Krishnamurthy, V; Ravibabu, K; Raghavan, S; Rajan, B K; Rajmohan, H R

2008-01-01

A study to monitor and estimate respirable particulate matter (RPM), toxic trace metal concentrations in the work environment was carried out in different sections of an integrated steel manufacturing industry. The average RPM concentration observed varied according to the section blast furnace was 2.41 mg/m;{3}; energy optimization furnace, 1.87 mg/m;{3}; sintering plant, 0.98 mg/m;{3}; continuous casting machine, 1.93 mg/m;{3}. The average trace metal concentration estimated from the RPM samples like iron, manganese, lead and chromium did not exceed ACGIH prescribed levels.

Determination of the ¹⁴C content in activated steel components from a neutron spallation source and a nuclear power plant.

PubMed

Schumann, Dorothea; Stowasser, Tanja; Volmert, Benjamin; Günther-Leopold, Ines; Linder, Hanspeter; Wieland, Erich

2014-06-03

The (14)C content in activated steel components from the Swiss Nuclear Power Plant (NPP) Gösgen and the Spallation Neutron Source SINQ at the Paul Scherrer Institute is determined using a wet chemistry digestion technique and liquid scintillation counting for (14)C activity measurements. The (14)C activity of an activated fuel assembly steel nut from the NPP is further compared with theoretical predictions made on the basis of a Monte Carlo reactor model for this NPP. Knowledge of the (14)C inventory in these activated steel materials is important in conjunction with future corrosion studies on these materials aimed at identifying the (14)C containing organic compounds possibly formed in the cement-based near field of a repository for radioactive waste.

6. DETAIL VIEW OF SPIN FORM FURNACE FOR STAINLESS STEEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. DETAIL VIEW OF SPIN FORM FURNACE FOR STAINLESS STEEL FABRICATION. STAINLESS STEEL WAS MACHINED IN SIDE A OF THE BUILDING, BEGINNING IN 1957. (4/24/78) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

Nuclear transmutation in steels

NASA Astrophysics Data System (ADS)

Belozerova, A. R.; Shimanskii, G. A.; Belozerov, S. V.

2009-05-01

The investigations of the effects of nuclear transmutation in steels that are widely used in nuclear power and research reactors and in steels that are planned for the application in thermonuclear fusion plants, which are employed under the conditions of a prolonged action of neutron irradiation with different spectra, made it possible to study the effects of changes in the isotopic and chemical composition on the tendency of changes in the structural stability of these steels. For the computations of nuclear transmutation in steels, we used a program complex we have previously developed on the basis of algorithms for constructing branched block-type diagrams of nuclide transformations and for locally and globally optimizing these diagrams with the purpose of minimizing systematic errors in the calculation of nuclear transmutation. The dependences obtained were applied onto a Schaeffler diagram for steels used for structural elements of reactors. For the irradiation in fission reactors, we observed only a weak influence of the effects of nuclear transmutation in steels on their structural stability. On the contrary, in the case of irradiation with fusion neutrons, a strong influence of the effects of nuclear transmutation in steels on their structural stability has been noted.

European developments in the application of structural austenitic and duplex stainless steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cochrane, D.J.

1995-12-31

Stainless steel is increasingly being specified for structural applications. Principally, this is due to the aesthetic appeal of the material, no need for surface protection, durability, and the growing awareness, and use, of Life Cycle Cost analysis for assessing costs over the longer term, However, use of stainless steel in the U.K. offshore oil and gas platforms for fire and blast walls, has highlighted valuable properties of stainless steel that may be unfamiliar to structural designers. It is the purpose of this paper to demonstrate these properties. Additionally, new design guidance has become available in Europe as a result ofmore » a 4 year research program into the structural use of stainless steel. The ``Design Manual for Structural Stainless Steel`` was issued by Euro Inox and the Nickel Development Institute in 1994. This new manual will be outlined in this paper together with its influence on new European Building Standards and new European material standards for structural stainless steel. Currently in preparation, these include high strength grades with significantly higher strength than structural carbon steels. Finally, this paper will address the use of stainless steel for the reinforcement of concrete structures.« less

North façade of crucible steel building; looking southwest Bethlehem ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

North façade of crucible steel building; looking southwest - Bethlehem Steel Corporation, South Bethlehem Works, Crucible Steel Plant, Along Lehigh River, North of Fourth Street, West of Minsi Trail Bridge, Bethlehem, Northampton County, PA

Comparison of the contributions of polychlorinated dibenzo-p-dioxins and dibenzofurans and other unintentionally produced persistent organic pollutants to the total toxic equivalents in air of steel plant areas.

PubMed

Li, Sumei; Liu, Guorui; Zheng, Minghui; Liu, Wenbin; Wang, Mei; Xiao, Ke; Li, Changliang; Wang, Yiwen

2015-05-01

The concentrations of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and the "dioxin-like" (dl) compounds polychlorinated biphenyls (PCBs), polychlorinated naphthalenes (PCNs), polybrominated dibenzo-p-dioxins (PBDDs), and dibenzofurans (PBDFs), were determined in the air samples collected from six steel plants. The toxic equivalent (TEQ) concentrations of the PCDDs, PCDFs, dl-PCBs, dl-PCNs, PBDDs, and PBDFs in the air were 0.01-0.19 pg WHO-TEQ Nm(-3), 0.01-0.69 pg WHO-TEQN m(-3), 0.001-0.089 pg WHO-TEQ Nm(-3), 0.002-0.011 pg TEQ Nm(-3), 0.004-0.02 pg TEQ Nm(-3), and 0.02-0.12 pg TEQ Nm(-3), respectively. The PCNs were the most abundant compounds (by mass concentration), contributing about 87% of the total mass concentrations of the analytes that were found in the air of the steel plant areas. The PCDFs contributed about 47% of the total TEQs, following by the PBDFs (28%) and the PCDDs (18%). The dioxin-like compounds together contributed up to 40% of the total TEQs, so their contributions to the toxic effects that could be caused by exposure to the air of the steel plant areas were significant. The congener profiles in the air were similar to the congener profiles that were found in stack gas emissions, indicating that the steelmaking plants were possible sources of the PCDDs, PCDFs, and dioxin-like compounds that were found in the air of the steel plant areas. Copyright © 2015 Elsevier Ltd. All rights reserved.

Increased energy efficiency of a steel foundry plant by using a cleaner production quick-E-scan methodology

NASA Astrophysics Data System (ADS)

Rasmeni, Zelda; Pan, Xiaowei

2017-07-01

The Quick-E-Scan methodology is a simple and quick method that is used to achieve operational energy efficiency as opposed to detailed energy audits, which therefore offers a no cost or less cost solutions for energy management programs with a limited budget. The quick-E-scan methodology was used to assesses a steel foundry plant based in Benoni through dividing the foundry into production sections which entailed a review of the current processes and usage patterns of energy within the plant and a detailed analysis of options available for improvement and profitable areas in which energy saving measures may be implemented for an increase energy efficiency which can be presented to management of the company.

30. LOOKING SOUTHEAST AT THE CLEAN STEEL PRODUCTION BUILDING WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

30. LOOKING SOUTHEAST AT THE CLEAN STEEL PRODUCTION BUILDING WITH THE BOP SHOP IN BACKGROUND. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Micronutrient availability from steel slag amendment in pine bark substrates

USDA-ARS?s Scientific Manuscript database

Steel slag is a byproduct of the steel industry that can be used as a liming agent, but also has a high mineral nutrient content. While micronutrients are present in steel slag, it is not known if the mineral form of the micronutrients would render them available for plant uptake. The objective of...

Steel Pickling Inspection Checklist

EPA Pesticide Factsheets

Checklist to establish whether a facility or operations within a facility are subject to and are in compliance with 40 C.F.R Part 63 Subpart CCC (Steel Pickling—HCl Process Facilities and Hydrochloric Acid Regeneration Plants NESHAP).

Evaluation of pitting corrosion resistance of high-alloyed stainless steels welds for FGD plants in Korea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baek, K.K.; Sung, H.J.; Im, C.S.

1998-12-31

For successful application of high-alloyed stainless steels for Flue Gas Desulfurization (FGD) plants, pitting corrosion resistance of arc welds of N-added 6%Mo austenitic stainless steels (UNS N 08367) and super duplex stainless steels (UNS S 32550) made with various filler metals were evaluated using the Green Death solution. For Gas Tungsten Arc (GTA) and Gas Metal Arc (GMA) welds of N 08367, Critical Pitting Temperature (CPT) of base metal was 65--70 C, whereas weld made by ERNiCrMo-3 filler metal yielded CPT of 50 C. Welds made by ERNiCrMo-10 or ERNiCrMo-4 filler metals showed CPT of 60--65 C and 65--70C, respectively.more » For GTA and GMA welds of S 32550, CPT of welds made by ERNiCrMo-3 was 45--50 C, indicating that the filler metal can provide pitting corrosion resistance matching the S 32550 alloy. Thus, a proper pitting corrosion resistance of weldments of high-alloy stainless steels can be achieved by selecting filler metals having at least +10 higher Pitting Resistance Equivalent Number (PRE{sub N}) value than the base metal regardless of the type of arc welding process. The over-alloyed filler metals would compensate preferential segregation of Cr, MO along the dendrite boundary, which made the dendrite core more susceptible to pitting. Nitrogen addition to the GTA welds of N 08367 made with ERNiCrMo-3 failed to improve pitting corrosion resistance, which was attributed to the precipitation of nitrogen in the weld metal in the form of Nb-nitride.« less

Mechanical characteristics of welded joints between different stainless steels grades

NASA Astrophysics Data System (ADS)

Topolska, S.; Łabanowski, J.

2017-08-01

Investigation of mechanical characteristics of welded joints is one of the most important tasks that allow determining their functional properties. Due to the very high, still rising, cost of some stainless steels it is justified, on economic grounds, welding austenitic stainless steel with steels that are corrosion-resistant like duplex ones. According to forecasts the price of corrosion resistant steels stil can increase by 26 ÷ 30%. For technical reasons welded joints require appropriate mechanical properties such as: tensile strength, bending, ductility, toughness, and resistance to aggressive media. Such joints are applied in the construction of chemical tankers, apparatus and chemical plants and power steam stations. Using the proper binder makes possible the welds directly between the elements of austenitic stainless steels and duplex ones. It causes that such joits behave satisfactorily in service in such areas like maritime constructions and steam and chemical plants. These steels have high mechanical properties such as: the yield strength, the tensile strength and the ductility as well as the resistance to general corrosion media. They are resistant to both pitting and stress corrosions. The relatively low cost of production of duplex steels, in comparison with standard austenitic steels, is inter alia, the result of a reduced amount of scarce and expensive Nickel, which is seen as a further advantage of these steels.

19. 1500 CUBIC FEET CAPACITY SCRAP STEEL CHARGING BOX ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. 1500 CUBIC FEET CAPACITY SCRAP STEEL CHARGING BOX ON THE CHARGING AISLE OF THE BOP SHOP LOOKING NORTHWEST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Installation and certification of continuous VOC emissions monitoring systems for a steel mill sinter plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, K.L.; Macak, J.J. III; Cioffi, J.

1999-07-01

The counties of Lake, Porter, and LaPorte in Northwest Indiana are classified as severe non-attainment for the ozone National Ambient Air Quality Standard (NAAQS). In response to the non-attainment problem, the Indiana Department of Environmental Management (IDEM) promulgated a number of regulations over the last several years. One of these rules requires steel mills with sinter plants to control and continuously monitor volatile organic compound (VOC) emissions from the facilities. One of the accepted compliance methods is to install and certify Continuous Emission Monitoring Systems (CEMS) to monitor VOC emissions and volumetric flow rate in order to generate a VOCmore » emission number in units of pounds per hour. Compliance with the regulation also requires that the sinter plants accurately monitor sinter production in order to determine compliance during the winter months, when the limits are based on pounds of VOC emissions per ton of sinter produced.« less

Characterization of polycyclic aromatic hydrocarbons in fugitive PM10 emissions from an integrated iron and steel plant.

PubMed

Khaparde, V V; Bhanarkar, A D; Majumdar, Deepanjan; Rao, C V Chalapati

2016-08-15

Fugitive emissions of PM10 (particles <10μm in diameter) and associated polycyclic aromatic hydrocarbons (PAHs) were monitored in the vicinity of coking unit, sintering unit, blast furnace and steel manufacturing unit in an integrated iron and steel plant situated in India. Concentrations of PM10, PM10-bound total PAHs, benzo (a) pyrene, carcinogenic PAHs and combustion PAHs were found to be highest around the sintering unit. Concentrations of 3-ring and 4-ring PAHs were recorded to be highest in the coking unit whereas 5-and 6-ring PAHs were found to be highest in other units. The following indicatory PAHs were identified: indeno (1,2,3-cd) pyrene, dibenzo (a,h) anthracene, benzo (k) fluoranthene in blast furnace unit; indeno (1,2,3-cd) pyrene, dibenzo (a,h) anthracene, chrysene in sintering unit; Anthracene, fluoranthene, chrysene in coking unit and acenaphthene, fluoranthene, fluorene in steel making unit. Total-BaP-TEQ (Total BaP toxic equivalent quotient) and BaP-MEQ (Total BaP mutagenic equivalent quotient) concentration levels ranged from 2.4 to 231.7ng/m(3) and 1.9 to 175.8ng/m(3), respectively. BaP and DbA (dibenzo (a,h) anthracene) contribution to total-BaP-TEQ was found to be the highest. Copyright © 2016 Elsevier B.V. All rights reserved.

A comparative assessment of waste incinerators in the UK.

PubMed

Nixon, J D; Wright, D G; Dey, P K; Ghosh, S K; Davies, P A

2013-11-01

The uptake in Europe of Energy from Waste (EfW) incinerator plants has increased rapidly in recent years. In the UK, 25 municipal waste incinerators with energy recovery are now in operation; however, their waste supply chains and business practices vary significantly. With over a hundred more plant developments being considered it is important to establish best business practices for ensuring efficient environmental and operational performance. By reviewing the 25 plants we identify four suitable case study plants to compare technologies (moving grate, fluidised bed and rotary kiln), plant economics and operations. Using data collected from annual reports and through interviews and site visits we provide recommendations for improving the supply chain for waste incinerators and highlight the current issues and challenges faced by the industry. We find that plants using moving grate have a high availability of 87-92%. However, compared to the fluidised bed and rotary kiln, quantities of bottom ash and emissions of hydrogen chloride and carbon monoxide are high. The uptake of integrated recycling practices, combined heat and power, and post incineration non-ferrous metal collections needs to be increased among EfW incinerators in the UK. We conclude that one of the major difficulties encountered by waste facilities is the appropriate selection of technology, capacity, site, waste suppliers and heat consumers. This study will be of particular value to EfW plant developers, government authorities and researchers working within the sector of waste management. Copyright © 2013 Elsevier Ltd. All rights reserved.

Spatial and seasonal distribution of polychlorinated biphenyls (PCBs) in the vicinity of an iron and steel making plant.

PubMed

Baek, Song-Yee; Choi, Sung-Deuk; Park, Hyokeun; Kang, Jung-Ho; Chang, Yoon-Seok

2010-04-15

Four consecutive passive air samplings (September 2006-July 2007) were conducted at 15 sites around an iron and steel making plant in Pohang, Korea to investigate the spatial and seasonal distributions of polychlorinated biphenyls (PCBs) and ultimately the source-receptor relationships. Annual mean values of Sigma(8)PCBs (IUPAC number 8, 28, 52, 101, 118, 138, 153, 180) were in the range of 15.1-166 pg/m(3) with an average of 53.0 pg/m(3). The spatial distribution of PCBs for each sampling period clearly suggests that the steel complex is a major source of PCBs in this area, and the prevailing winds facilitated the atmospheric transport and dispersion of PCBs from the steel complex to the surrounding areas. Seasonal patterns of PCBs were observed clearly, which were influenced by meteorological conditions; the highest levels of PCBs were observed with the highest average air temperature, and the influence of rainfall (i.e., wet scavenging) was also observed. In addition, PCB 11, a non-Aroclor congener, was detected in high concentrations at all sites, implying that the sources of PCB 11 are both unique and ubiquitous. This study confirms that passive air sampling is a useful tool to obtain seasonal and spatial distributions of time-averaged POPs data at a local scale.

Native Michigan plants stimulate soil microbial species changes and PAH remediation at a legacy steel mill.

PubMed

Thomas, John C; Cable, Edward; Dabkowski, Robert T; Gargala, Stephanie; McCall, Daniel; Pangrazzi, Garett; Pierson, Adam; Ripper, Mark; Russell, Donald K; Rugh, Clayton L

2013-01-01

A 1.3-acre phytoremediation site was constructed to mitigate polyaromatic hydrocarbon (PAH) contamination from a former steel mill in Michigan. Soil was amended with 10% (v/v) compost and 5% (v/v) poultry litter. The site was divided into twelve 11.89 m X 27.13 m plots, planted with approximately 35,000 native Michigan perennials, and soils sampled for three seasons. Soil microbial density generally increased in subplots of Eupatorium perfoliatum (boneset), Aster novae-angliae (New England aster), Andropogon gerardii (big bluestem), and Scirpus atrovirens (green bulrush) versus unplanted subplots. Using enumeration assays with root exudates, PAH degrading bacteria were greatest in soils beneath plants. Initially predominant, Arthrobacter were found capable of degrading a PAH cocktail in vitro, especially upon the addition of root exudate. Growth of some Arthrobacter isolates was stimulated by root exudate. The frequency of Arthrobacter declined in planted subplots with a concurrent increase in other species, including secondary PAH degraders Bacillus and Nocardioides. In subplots supporting only weeds, an increase in Pseudomonas density and little PAH removal were observed. This study supports the notion that a dynamic interplay between the soil, bacteria, and native plant root secretions likely contributes to in situ PAH phytoremediation.

New Nano-Particle-Strengthened Ferritic/Martensitic Steels By Conventional Thermomechanical Treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klueh, Ronald L; Hashimoto, Naoyuki; Maziasz, Philip J

2007-01-01

For increased fusion power plant efficiency, steels for operation at 650 C and higher are sought. Based on the science of precipitate strengthening, a thermo-mechanical treatment (TMT) was developed that increased the strength from room temperature to 700 C of commercial nitrogen-containing steels and new steels designed for the TMT. At 700 C increases in yield stress of 80 and 200% were observed for a commercial steel and a new steel, respectively, compared to commercial normalized-and-tempered steels. Creep-rupture strength was similarly improved. Depending on the TMT, precipitates were up to eight-times smaller at a number density four orders of magnitudemore » greater than those in a conventionally heat treated steel of similar composition.« less

[Characteristics of working conditions at metallurgy-related plants].

PubMed

Egorova, A M

2008-01-01

Working conditions at more versus less advanced technology steel plants of the Volgograd Region are analyzed. The working conditions at the less advanced technology plants are referred to as a very high occupational risk. It is necessary to work out measures to lower the poor impact of microclimate, dust, noise, to improve illumination, and to regulate labor at steel plants.

Mortality of iron and steel workers in Korea.

PubMed

Park, Robert M; Ahn, Yeon-Soon; Stayner, Leslie T; Kang, Seong-Kyu; Jang, Jae-Kil

2005-09-01

The mortality experience of iron and steel workers from modern plants in developing countries has not been extensively described. Mortality at two Korean iron and steel manufacturing complexes was analyzed using Poisson regression methods with both direct and indirect standardization. Work histories were linked with a national mortality registry. Workers (44,974) hired beginning in 1968 were followed from 1992 to 2001. The 806 deaths observed during 10 years of follow-up comprised 2% of the population at risk and represented a large healthy worker effect (HWE) for all causes (SMR = 0.59, 95% CI = 0.55-0.63) and for cancer (SMR = 0.79, 95% CI = 0.70-0.90). Mortality at subsidiaries was considerably higher than at the parent plants (SRR = 1.71, 95% CI = 1.47-1.99). Relative mortality rates declined with employment duration: > 20 years had significantly reduced mortality (SRR = 0.59, 95% CI = 0.43-0.82) compared to duration < 1 year (test for trend: P = 0.0006). Fatal injury deaths in the first year were highly elevated (SMR = 3.10, 95% CI = 2.17-4.26) declining to less than that expected after 5 years. Cancer mortality was elevated in stainless steel production (SRR = 3.26, 95% CI = 1.37-6.49) and overall mortality was elevated for work in plant maintenance departments (SRR = 1.17, 95% CI = 1.00-1.37), particularly for fatal injuries (SRR = 1.67, 95% CI = 1.29-2.14). All-cause mortality increased with employment duration in the steel-production departments, as did fatal injuries in material handling/construction. This steelworker cohort exhibits excess mortality in some process areas. More detailed retrospective exposure assessment and future follow-up of this cohort will better define health risks in the modern iron and steel manufacturing.

Study of spatiotemporal variation of atmospheric mercury and its human exposure around an integrated steel plant, India

NASA Astrophysics Data System (ADS)

Pervez, S.; Koshle, A.; Pervez, Y.

2010-01-01

Mercury release by coal combustion has been significantly increased in India. Mercury content in coal has been analyzed to 0.272 ppm by Central Pollution Control Board. Toxicological effects of elemental Hg (Hg0) exposure include respiratory and renal failures, cardiac arrest, and cerebral oedema, while subclinical exposure may induce kidney, behavioral, and cognitive dysfunctions. The present work is focused on dispersion pattern and inter-phase exchange phenomena of ambient mercury between air-particulate matter evaluations of alongwith dominance of various major routes of human exposure-dose response using regression analysis around an integrated steel plant in central India. Source-downwind type stratified random sampling plan using longitudinal study design has been adopted for ambient monitoring of total mercury, while representative sampling plant has been adopted for persona exposure-dose response study In space-time framework. Control sites and subjects have been chosen from uncontaminated area (100 km away from any industrial activities). 06 ambient air monitoring stations and 17 subjects from workers, non-workers but local residents' categories and from controlled sites have been chosen for the study. Samples of mercury biomarkers (blood, breast milk and urine) have also been collected from same subjects in each month during sampling period. The sampling period was March 2005 to February 2006 . Samples of 30% acidified KMnO4 for air-Hg absorption, PM10, RPM and biological samples were analyzed for total mercury by ICP-AES using standard methods. Local soils and ground water were also monitored for total mercury content during the sampling period. Results have shown that mercury concentration is very high compared to prescribed limits in all receptors. Results of exchange phenomenon have shown the higher transfer of mercury from air to particulate during combustion in steel plant environment due to presence of huge amount of iron particles, in contrast to

Study of spatiotemporal variation of atmospheric mercury and its human exposure around an integrated steel plant, India

NASA Astrophysics Data System (ADS)

Pervez, S.; Koshle, A.; Pervez, Y.

2010-06-01

Mercury release by coal combustion has been significantly increased in India. Mercury content in coal has been analyzed to 0.272 ppm by Central Pollution Control Board. Toxicological effects of elemental Hg (Hg0) exposure include respiratory and renal failures, cardiac arrest, and cerebral oedema, while subclinical exposure may induce kidney, behavioral, and cognitive dysfunctions. The present work is focused on dispersion pattern and inter-phase exchange phenomena of ambient mercury between air-particulate matter evaluations of alongwith dominance of various major routes of human exposure-dose response using regression analysis around an integrated steel plant in central India. Source-downwind type stratified random sampling plan using longitudinal study design has been adopted for ambient monitoring of total mercury, while representative sampling plant has been adopted for persona exposure-dose response study In space-time framework. Control sites and subjects have been chosen from uncontaminated area (100 km away from any industrial activities). 06 ambient air monitoring stations and 17 subjects from workers, non-workers but local residents' categories and from controlled sites have been chosen for the study. Samples of mercury biomarkers (blood, breast milk and urine) have also been collected from same subjects in each month during sampling period. The sampling period was March 2005 to February 2006 . Samples of 30% acidified KMnO4 for air-Hg absorption, PM10, RPM and biological samples were analyzed for total mercury by ICP-AES using standard methods. Local soils and ground water were also monitored for total mercury content during the sampling period. Results have shown that mercury concentration is very high compared to prescribed limits in all receptors. Results of exchange phenomenon have shown the higher transfer of mercury from air to particulate during combustion in steel plant environment due to presence of huge amount of iron particles, in contrast to

J-R fracture characteristics of ferritic steels for RPVs and RCS piping of nuclear power plants

NASA Astrophysics Data System (ADS)

Yoon, Ji-Hyun; Lee, Bong-Sang; Hong, Jun-Hwa

2001-10-01

J-R fracture resistance tests have been performed on 3 heats of SA508-Gr.3 nuclear reactor pressure vessel (RPV) steel as well as 2 heats of SA516-Gr.70 and a heat of SA508-Gr.1a steels for nuclear reactor coolant system (RCS) piping. For the latter two steels, dynamic in addition to static J-R fracture resistances were investigated. From the test results of the SA508-Gr.3 steels, the J-R fracture resistance was superior in the following order: Si-killing steel, modified VCD steel and VCD steel. Microstructural analyses were carried out to correlate J-R fracture resistances with microstructural characteristics. According to the test results for SA508-Gr.1a and SA516-Gr.70 steels, all of the tested steels showed steep drops in fracture resistance at certain temperature and loading rate combinations. One heat of SA516-Gr.70 steel was very sensitive to dynamic strain aging and its fracture resistance was significantly low. It was concluded that microstructural and chemical factors affect the J-R fracture and DSA characteristics of SA516-Gr.70 steels.

Management of MSW in Spain and recovery of packaging steel scrap.

PubMed

Tayibi, Hanan; Peña, Carmen; López, Félix A; López-Delgado, Aurora

2007-01-01

Packaging steel is more advantageously recovered and recycled than other packaging material due to its magnetic properties. The steel used for packaging is of high quality, and post-consumer waste therefore produces high-grade ferrous scrap. Recycling is thus an important issue for reducing raw material consumption, including iron ore, coal and energy. Household refuse management consists of collection/disposal, transport, and processing and treatment - incineration and composting being the most widely used methods in Spain. Total Spanish MSW production exceeds 21 million tons per year, of which 28.1% and 6.2% are treated in compost and incineration plants, respectively. This paper presents a comprehensive study of incineration and compost plants in Spain, including a review of the different processes and technologies employed and the characteristics and quality of the recovered ferrous scrap. Of the total amount of packaging steel scrap recovered from MSW, 38% comes from compost plants and 14% from incineration plants. Ferrous scrap from incineration plants presents a high degree of chemical alteration as a consequence of the thermal process to which the MSW is subjected, particularly the conditions in which the slag is cooled, and accordingly its quality diminishes. Fragmentation and magnetic separation processes produce an enhancement of the scrap quality. Ferrous scrap from compost plants has a high tin content, which negatively affects its recycling. Cleaning and detinning processes are required prior to recycling.

Steels with controlled hardenability for induction hardening

NASA Astrophysics Data System (ADS)

Shepelyakovskii, K. Z.

1980-07-01

Steels of the CH and LH type developed in the Soviet Union permit the use of a new method of induction hardening — bulk-surface hardening — and efficient utilization of the high-strength conditions (σb = 230-250 kgf/mm2). These steels make it possible to improve the structural strength, operating characteristics, service life, and reliability of critical heavily loaded machine parts. At the same time, CH steels make it possible to reduce by a factor of 2-3 the quantity of alloying elements, reduce the electrical energy for heat treatment, and completely exclude the cost of quenching oil for heat treatment in automatic equipment with high labor productivity, while retaining good working conditions. All this leads to substantial savings in production and operation. For example, when transmission gears (cylindrical and conical) are manufactured from LH steels the annual savings amount to more than 700,000 rubles at two automobile plants. Machine parts of CH steels — half axles and bearings in railway cars —have saved respectively six and four million rubles annually. The introduction of controlled-hardenability steels for induction hardening is a necessary condition for technological progress in machine construction and metallurgy.

Generation of Electricity Using Spartina Patens with Stainless Steel Current Collectors in a Plant-Microbial Fuel Cell

NASA Astrophysics Data System (ADS)

Narula, Deep

At present, the global energy infrastructure is highly dependent on (i) non-renewable fossil fuels with significant emissions of greenhouse gasses (ii) green fuels such as bioethanol and biodiesel with impact on current agricultural practices competing with food production for arable lands, fertilizers, also requiring additional energy input. Plant-based microbial fuel cell (PMFC) technology can be found as a promising alternative to produce electricity without any side effects with an advantage of using sunlight as an energy source. In the present study, we developed PMFCs using Spartina patens, a marshland grass, abundantly available in the coastal regions of the USA. Figure 1 is a schematic for a PMFC with the anode and cathode compartments where others have used carbon-based electrodes for current collection. In contrast, we attempted to utilize stainless steel wires with more surface area to enhance the current collection in the anode compartment as well as to increase the rate of reduction in the cathode chamber and thereby increase the amount of electricity produced. The study will give results on the periodic use of Spartina patens in PMFC along with the porous stainless steel electrodes which have never been employed in PMFCs before.

Transuranic contamination of stainless steel in nitric acid

NASA Astrophysics Data System (ADS)

Kerry, Timothy; Banford, Anthony W.; Thompson, Olivia R.; Carey, Thomas; Schild, Dieter; Geist, Andreas; Sharrad, Clint A.

2017-09-01

Stainless steels coupons have been exposed to transuranic species in conditions representative of those found in a spent nuclear fuel reprocessing plant. Stainless steel was prepared to different surface finishes and exposed to nitric acid of varying concentrations containing 237Np, 239Pu or 243Am for one month at 50 °C. Contamination by these transuranics has been observed on all surfaces exposed to the solution through the use of autoradiography. This technique showed that samples held in 4 M HNO3 bind 2-3 times as much radionuclide as those held in 10.5 M HNO3. It was also found that the polished steel surfaces generally took up more transuranic contamination than the etched and "as received" steel finishes. The extent of corrosion on the steel surfaces was found, by scanning electron microscopy, to be greater in solutions containing Np and Pu in comparison to that observed from contact with Am containing solutions, indicating that redox activity of transuranics can influence the mechanism of stainless steel corrosion.

High-temperature creep properties and life predictions for T91 and T92 steels

NASA Astrophysics Data System (ADS)

Pan, J. P.; Tu, S. H.; Sun, G. L.; Zhu, X. W.; Tan, L. J.; Hu, B.

2018-01-01

9-11%Cr heat-resistant steels are widely used in high-temperature and high-pressure boilers of advanced power plants. In the current paper, high-temperature creep behaviors of T91 and T92 steels have been investigated. Creep tests were performed for both steels at varied temperatures. The creep mechanisms of T91 and T92 steels were elucidated by analyzing the creep rupture data of the two steels. In addition, Manson-Haferd model was employed to predict the creep life of T91 and T92 steels, the results of which indicate that the Manson-Haferd model works well for the two steels.

Bioremediation of steel plant wastewater and enhanced electricity generation in microbial desalination cell.

PubMed

Shinde, Omkar A; Bansal, Ankita; Banerjee, Angela; Sarkar, Supriya

2018-05-01

Microbial desalination cell (MDC) is a propitious technology towards water desalination by utilizing wastewater as an energy source. In this study, a multi-chambered MDC was used to bioremediate steel plant wastewater using the same wastewater as a fuel for anodic bacteria. A pure culture of Pseudomonas putida MTCC 1194 was isolated and inoculated to remove toxic phenol. Three different inoculum conditions, namely P. putida (INC-A), a mixture of P. putida and activated sludge (INC-B), and activated sludge alone (INC-C) were employed in an anodic chamber to mainly compare the electricity generation and phenol degradation in MDCs. The study revealed the maximum phenol removal of 82 ± 2.4%, total dissolved solids (TDS) removal of 68 ± 1.5%, and power generation of 10.2 mW/m 2 using INC-B. The synergistic interactions between microorganisms, can enhance the toxic phenol degradation and also electricity generation in MDC for onsite wastewater application.

Constructed wetlands in UK urban surface drainage systems.

PubMed

Shutes, B; Ellis, J B; Revitt, D M; Scholes, L N L

2005-01-01

This paper presents the outcome of an inventory of planted wetland systems in the UK which are classified according to land use type and are all examples of sustainable drainage systems. The introduction of constructed wetlands to treat surface runoff essentially followed a 1997 Environment Agency for England and Wales report advocating the use of "soft engineered" facilities including wetlands in the context of sustainable development and Agenda 21. Subsequently published reports by the UK Construction Industry Research and Information Association (CIRIA) have promoted the potential benefits to both developer and the community of adopting constructed wetlands and other vegetated systems as a sustainable drainage approach. In addition, the UK Environment Agency and Highways Agency (HA) have recently published their own design criteria and requirements for vegetative control and treatment of road runoff. A case study of the design and performance of a constructed wetland system for the treatment of road runoff is discussed. The performance of these systems will be assessed in terms of their design criteria, runoff loadings as well as vegetation and structure maintenance procedures. The differing design approaches in guidance documents published in the UK by the Environment Agency, CIRIA and HA will also be evaluated.

65. Neg. No. F99, Dec 27, 1931, INTERIORPRESSED STEEL BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

65. Neg. No. F-99, Dec 27, 1931, INTERIOR-PRESSED STEEL BUILDING FACING SOUTH TOWARD WAREHOUSE AND ASSEMBLY BUILDING 1ST FLOOR, EAST SIDE FACING SOUTH, SHOWING PRESSED STEEL MACHINERY AND RAILROAD CARS - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

Effect of heat treatment on microstructure and hardness of Grade 91 steel

DOE PAGES

Shrestha, Triratna; Alsagabi, Sultan; Charit, Indrajit; ...

2015-01-21

The modified 9Cr-1Mo steel (Grade 91) is a material of choice in fossil-fuel-fired power plants with increased efficiency, service life, and reduction in emission of greenhouse gases. It is also considered a prospective material for the Next Generation Nuclear Power Plant for application in reactor pressure vessels at temperatures up to 650°C. In this paper, heat treatment of the modified 9Cr-1Mo steel was studied by normalizing and tempering the steel at various temperatures and times, with the ultimate goal of improving its creep resistance and optimizing material hardness. The microstructural evolution of the heat treated steels was correlated with themore » differential scanning calorimetric results. Optical microscopy, scanning and transmission electron microscopy in conjunction with microhardness profiles and calorimetric plots were used to understand the evolution of microstructure including precipitate structures in modified 9Cr-1Mo steel and relate it to the mechanical behavior of the steel. Thermo-CalcTM calculations were used to support experimental work and provide guidance in terms of the precipitate stability and microstructural evolution. Furthermore, the carbon isopleth and temperature dependencies of the volume fraction of different precipitates were constructed. The predicted and experimentally observed results were found to be in good agreement.« less

Metal distribution in urban soil around steel industry beside Queen Alia Airport, Jordan.

PubMed

Al-Khashman, Omar A; Shawabkeh, Reyad A

2009-12-01

The objective of this study was to assess the extent and severity of metal contamination in urban soil around Queen Alia Airport, Jordan. Thirty-two soil samples were collected around steel manufacturing plants located in the Al-Jiza area, south Jordan, around the Queen Alia Airport. The samples were obtained at two depths, 0-10 and 10-20 cm, and were analyzed by atomic absorption spectrophotometry for lead (Pb), zinc (Zn), cadmium (Cd), iron (Fe), copper (Cu) and chromium (Cr) levels. The physicochemical factors believed to affect the mobility of metals in the soil of the study area were also examined, including pH, electrical conductivity, total organic matter, calcium carbonate (CaCO(3)) content and cation exchange capacity. The high concentrations of Pb, Zn and Cd in the soil samples were found to be related to anthropogenic sources, such as the steel manufacturing plants, agriculture and traffic emissions, with the highest concentrations of these metals close to the site of the steel plants; in contrast the concentration of Cr was low in the soil sampled close to the steel plants. The metals were concentrated in the surface soil, and concentrations decreased with increasing depth, reflecting the physical properties of the soil and its alkaline pH. The mineralogical composition of the topsoil, identified by X-ray diffraction, was predominantly quartz, calcite, dolomite and minor minerals, such as gypsum and clay minerals. Metal concentrations were compared using one-way analysis of variance (ANOVA) to compute the statistical significance of the mean. The results of the ANOVA showed significant differences between sites for Pb, Cd and Cu, but no significant differences for the remaining metals tested. Factor analysis revealed that polluted soil occurs predominantly at sites around the steel plants and that there is no significant variation in the characteristics of the unpolluted soil, which are uniform in the study area.

Creep Deformation, Rupture Analysis, Heat Treatment and Residual Stress Measurement of Monolithic and Welded Grade 91 Steel for Power Plant Components

NASA Astrophysics Data System (ADS)

Shrestha, Triratna

Modified 9Cr-1 Mo (Grade 91) steel is currently considered as a candidate material for reactor pressure vessels (RPVs) and reactor internals for the Very High Temperature Reactor (VHTR), and in fossil-fuel fired power plants at higher temperatures and stresses. The tensile creep behavior of Grade 91 steel was studied in the temperature range of 600°C to 750°C and stresses between 35 MPa and 350 MPa. Heat treatment of Grade 91 steel was studied by normalizing and tempering the steel at various temperatures and times. Moreover, Thermo-Ca1c(TM) calculation was used to predict the precipitate stability and their evolution, and construct carbon isopleths of Grade 91 steel. Residual stress distribution across gas tungsten arc welds (GTAW) in Grade 91 steel was measured by the time-of-flight neutron diffraction using the Spectrometer for Materials Research at Temperature and Stress (SMARTS) diffractometer at Lujan Neutron Scattering Center, Los Alamos National Laboratory, Los Alamos, NM, USA. Analysis of creep results yielded stress exponents of ˜9-11 in the higher stress regime and ˜1 in the lower stress regime. The creep behavior of Grade 91 steel was described by the modified Bird-Mukherjee-Dorn relation. The rate-controlling creep deformation mechanism in the high stress regime was identified as the edge dislocation climb with a stress exponent of n = 5. On the other hand, the deformation mechanism in the Newtonian viscous creep regime (n = 1) was identified as the Nabarro-Herring creep. Creep rupture data were analyzed in terms of Monkman-Grant relation and Larson-Miller parameter. Creep damage tolerance factor and stress exponent were used to identify the cause of creep damage. The fracture surface morphology of the ruptured specimens was studied by scanning electron microscopy to elucidate the failure mechanisms. Fracture mechanism map for Grade 91 steel was developed based on the available material parameters and experimental observations. The microstructural

Assessment of exposure to PCDD/F, PCB, and PAH at a basic oxygen Steelmaking (BOS) and an iron ore sintering plant in the UK.

PubMed

Jackson, Kevin; Aries, Eric; Fisher, Raymond; Anderson, David R; Parris, Adrian

2012-01-01

An assessment was carried out at a UK integrated steelworks to investigate the exposure of workers via inhalation to dioxins [polychlorinated dibenzo-p-dioxins (PCDD/F)], polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAH) including benzo[a]pyrene (B[a]P). Investigations focused on a basic oxygen steelmaking (BOS) plant and an iron ore sintering plant. The highest concentrations of PCDD/F and dioxin-like PCB were found at the BOS vessels and sinter strand area at the BOS and sinter plant, respectively. A risk assessment was carried out by comparing the daily intake of PCDD/F and PCB via inhalation with the recommended tolerable daily intake (TDI) proposed by the World Health Organisation (WHO). For the most exposed category of worker in this study (i.e. sinter plant workers inside the strand area), the estimated daily intake via inhalation was estimated to be 0.25 pg WHO-toxic equivalent concentrations (TEQ) kg(-1) body weight (bw). Considering that the average UK adult exposure to PCDD/F from the diet is 1.8 pg WHO-TEQ kg(-1) bw day(-1), the results indicated that the estimated daily intake of PCDD/F and PCB via inhalation for sinter plant workers would not result in the recommended range of the TDI (1-4 pg WHO-TEQ kg(-1) bw day(-1)) being exceeded. Cancer risks for a 40-year occupational exposure period were determined by multiplying the estimated intake by the inhalation cancer potency factor for 2,3,7,8-tetrachlorodibenzo-p-dioxin. For the most exposed category of worker, cancer risks from exposure to PCDD/F and PCB ranged from 2.5 × 10(-6) to 5.2 × 10(-5). Under most regulatory programmes, excess cancer risks between 1.0 × 10(-6) and 1.0 × 10(-4) indicate an acceptable range of cancer risk, suggesting a limited risk from PCDD/F and PCB exposure for workers in the sinter plant. With regard to PAH, B[a]P concentrations were typically <10 ng m(-3) at all locations at both the sinter plant and the BOS plant. In several cases

Heavy-Section Steel Irradiation Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosseel, T.M.

2000-04-01

Maintaining the integrity of the reactor pressure vessel (RPV) in a light-water-cooled nuclear power plant is crucial in preventing and controlling severe accidents that have the potential for major contamination release. Because the RPV is the only key safety-related component of the plant for which a redundant backup system does not exist, it is imperative to fully understand the degree of irradiation-induced degradation of the RPV's fracture resistance that occurs during service. For this reason, the Heavy-Section Steel Irradiation (HSSI) Program has been established.

Steel selection for UBC steel bridge

NASA Astrophysics Data System (ADS)

Liu, Haoyu

2018-03-01

This report conducts a material selection of different types of steel for UBC Steel Bridge Team. I am a third-year material engineering student, so the result from this material selection can only be taken into consideration but not fully adopted. As part of my academic journey, it is possible for technical mistakes in this material selection process. The mechanic properties are the most effective category of properties, making it necessary to be justified from the steel bridge design and chosen in accordance with the objective of the team. An introduction for currently-used steel properties and the expected steel properties is provided. The examination focus on how different alloy compositions of steel changes its properties. The properties of the steel are examined in three main aspects: hardness, strength, and toughness. The results suggest that more nickel, manganese, and chromium in the steel provide better steel for the team to use. Further research is needed if a more precise material selection is required.

The use of solid wastes as a fuel in the cement industry in the UK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haley, C.A.C.; Chatterton, M.H.

1985-01-01

Blue Circle has installed a commercial plant for processing and firing MSW as a fuel in cement kilns. The plant, a world first, has operated successfully since 1979 at Wiltshire, UK. By the end of January 1984, 173,000 tonnes of refuse had been processed.

Prediction of stress corrosion of carbon steel by nuclear process liquid wastes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ondrejcin, R.S.

1978-08-01

Radioactive liquid wastes are produced as a consequence of processing fuel from Savannah River Plant (SRP) production reactors. These wastes are stored in mild steel waste tanks, some of which have developed cracks from stress corrosion. A laboratory test was developed to determine the relative agressiveness of the wastes for stress corrosion cracking of mild steel. Tensile samples were strained to fracture in synthetic waste solutions in an electrochemical cell with the sample as the anode. Crack initiation is expected if total elongation of the steel in the test is less than its uniform elongation in air. Cracking would bemore » anticipated in a plant waste tank if solution conditions were equivalent to test conditions that cause a total elongation that is less than uniform elongation. The electrochemical tensile tests showed that the supernates in salt receiver tanks at SRP have the least aggressive compositions, and wastes newly generated during fuel repocessing have the most aggressive ones. Test data also verified that ASTM A 516-70 steel used in the fabrication of the later design waste tanks is less susceptible to cracking than the ASTM A 285-B steel used in earlier designs.« less

Thallium contamination in arable soils and vegetables around a steel plant-A newly-found significant source of Tl pollution in South China.

PubMed

Liu, Juan; Luo, Xuwen; Wang, Jin; Xiao, Tangfu; Chen, Diyun; Sheng, Guodong; Yin, Meiling; Lippold, Holger; Wang, Chunlin; Chen, Yongheng

2017-05-01

Thallium (Tl) is a highly toxic rare element. Severe Tl poisoning can cause neurological brain damage or even death. The present study was designed to investigate contents of Tl and other associated heavy metals in arable soils and twelve common vegetables cultivated around a steel plant in South China, a newly-found initiator of Tl pollution. Potential health risks of these metals to exposed population via consumption of vegetables were examined by calculating hazard quotients (HQ). The soils showed a significant contamination with Tl at a mean concentration of 1.34 mg/kg. The Tl levels in most vegetables (such as leaf lettuce, chard and pak choy) surpassed the maximum permissible level (0.5 mg/kg) according to the environmental quality standards for food in Germany. Vegetables like leaf lettuce, chard, pak choy, romaine lettuce and Indian beans all exhibited bioconcentration factors (BCF) and transfer factors (TF) for Tl higher than 1, indicating a hyperaccumulation of Tl in these plants. Although the elevated Tl levels in the vegetables at present will not immediately pose significant non-carcinogenic health risks to residents, it highlights the necessity of a permanent monitoring of Tl contamination in the steel-making areas. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hydrogen Embrittlement of Automotive Advanced High-Strength Steels

NASA Astrophysics Data System (ADS)

Lovicu, Gianfranco; Bottazzi, Mauro; D'Aiuto, Fabio; De Sanctis, Massimo; Dimatteo, Antonella; Santus, Ciro; Valentini, Renzo

2012-11-01

Advanced high-strength steels (AHSS) have a better combination between strength and ductility than conventional HSS, and higher crash resistances are obtained in concomitance with weight reduction of car structural components. These steels have been developed in the last few decades, and their use is rapidly increasing. Notwithstanding, some of their important features have to be still understood and studied in order to completely characterize their service behavior. In particular, the high mechanical resistance of AHSS makes hydrogen-related problems a great concern for this steel grade. This article investigates the hydrogen embrittlement (HE) of four AHSS steels. The behavior of one transformation induced plasticity (TRIP), two martensitic with different strength levels, and one hot-stamping steels has been studied using slow strain rate tensile (SSRT) tests on electrochemically hydrogenated notched samples. The embrittlement susceptibility of these AHSS steels has been correlated mainly to their strength level and to their microstructural features. Finally, the hydrogen critical concentrations for HE, established by SSRT tests, have been compared to hydrogen contents absorbed during the painting process of a body in white (BIW) structure, experimentally determined during a real cycle in an industrial plant.

Comparison of Geometric Design of a Brand of Stainless Steel K-Files: An In Vitro Study.

PubMed

Saeedullah, Maryam; Husain, Syed Wilayat

2018-04-01

The purpose of this experimental study was to determine the diametric variations of a brand of handheld stainless-steel K-files, acquired from different countries, in accordance with the available standards. 20 Mani stainless-steel K-files of identical size (ISO#25) were acquired from Pakistan and were designated as Group A while 20 Mani K-files were purchased from London, UK and designated as Group B. Files were assessed using profile projector Nikon B 24V. Data was statistically compared with ISO 3630:1 and ADA 101 by one sample T test. Significant difference was found between Groups A and B. Average discrepancy of Group A fell within the tolerance limit while that of Group B exceeded the limit. Findings in this study call attention towards adherence to the dimensional standards of stainless-steel endodontic files.

Determination of toughness and embrittlement for reactor pressure vessel steels using ultrasonic measurements

NASA Astrophysics Data System (ADS)

Hiser, Allen Lee, Jr.

Neutron irradiation embrittlement of nuclear reactor pressure vessel (RPV) steels results in a loss of fracture toughness (e.g., reduction in load carrying capacity of the steel). For the setting of operational limits and assuring the continued safe operation of the plant, current procedures estimate the effects of neutron embrittlement using empirical relations or the results of small samples irradiated in the plant. These procedures account for uncertainties in the estimates through the use of margin terms to ensure the conservatism of the resultant estimate vis-a-vis the "real" material toughness. Therefore, the ability to develop non destructive measurements that can estimate the actual RPV steel fracture toughness in situ would provide more accurate evaluations of operating limits for plants. This study was undertaken to evaluate the suitability of ultrasonic attenuation measurements for estimating the fracture toughness of RPV steels. Ultrasonic measurements were made on samples in three distinct phases: (1) a heat treated RPV steel to induce changes in its fracture toughness; (2) several irradiated RPV steels to assess actual neutron embrittlement changes in fracture toughness; and (3) a matrix of unirradiated RPV steels with a range of as fabricated toughness levels. The results indicate that ultrasonic attenuation is generally able to identify differences in responses for samples with different toughness levels, although in some cases the differences in ultrasonic responses are small. The results from the three phases are not consistent, as in some cases reduced toughness results in higher attenuation and in other cases lower attenuation. This trend is not surprising given the different types of microstructural changes that result in the toughness changes for each phase of this work. In addition, different trends were identified for plate and weld materials.

Mapping allergenic pollen vegetation in UK to study environmental exposure and human health.

PubMed

McInnes, Rachel N; Hemming, Deborah; Burgess, Peter; Lyndsay, Donna; Osborne, Nicholas J; Skjøth, Carsten Ambelas; Thomas, Sam; Vardoulakis, Sotiris

2017-12-01

Allergenic pollen is produced by the flowers of a number of trees, grasses and weeds found throughout the UK. Exposure to such pollen grains can exacerbate pollen-related asthma and allergenic conditions such as allergic rhinitis (hay fever). Maps showing the location of these allergenic taxa have many applications: they can be used to provide advice on risk assessments; combined with health data to inform research on health impacts such as respiratory hospital admissions; combined with weather data to improve pollen forecasting systems; or as inputs to pollen emission models. In this study we present 1km resolution maps of 12 taxa of trees, grass and weeds found in the UK. We have selected the main species recorded by the UK pollen network. The taxa mapped in this study were: Alnus (alder), Fraxinus (ash), Betula (birch), Corylus (hazel), Quercus (oak), Pinus (pine) and Salix (willow), Poaceae (grass), Artemisia (mugwort), Plantago (plantain), Rumex (dock, sorrels) and Urtica (nettle). We also focus on one high population centre and present maps showing local level detail around the city of London. Our results show the different geographical distributions of the 12 taxa of trees, weeds and grass, which can be used to study plants in the UK associated with allergy and allergic asthma. These maps have been produced in order to study environmental exposure and human health, although there are many possible applications. This novel method not only provides maps of many different plant types, but also at high resolution across regions of the UK, and we uniquely present 12 key plant taxa using a consistent methodology. To consider the impact on human health due to exposure of the pollen grains, it is important to consider the timing of pollen release, and its dispersal, as well as the effect on air quality, which is also discussed here. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

An Introduction to ESERO-UK, the UK Space Education Office

ERIC Educational Resources Information Center

Clements, Allan; Mather, Edward

2012-01-01

This article introduces the UK branch of the European Space Education Resource Office (ESERO-UK), also known as the UK Space Education Office. It is a teaching project designed to use space to enthuse primary and secondary students to study science, technology, engineering and mathematics (STEM) subjects. The office is funded by the European Space…

Improved representation of plant functional types and physiology in the Joint UK Land Environment Simulator (JULES v4.2) using plant trait information

NASA Astrophysics Data System (ADS)

Harper, Anna B.; Cox, Peter M.; Friedlingstein, Pierre; Wiltshire, Andy J.; Jones, Chris D.; Sitch, Stephen; Mercado, Lina M.; Groenendijk, Margriet; Robertson, Eddy; Kattge, Jens; Bönisch, Gerhard; Atkin, Owen K.; Bahn, Michael; Cornelissen, Johannes; Niinemets, Ülo; Onipchenko, Vladimir; Peñuelas, Josep; Poorter, Lourens; Reich, Peter B.; Soudzilovskaia, Nadjeda A.; van Bodegom, Peter

2016-07-01

Dynamic global vegetation models are used to predict the response of vegetation to climate change. They are essential for planning ecosystem management, understanding carbon cycle-climate feedbacks, and evaluating the potential impacts of climate change on global ecosystems. JULES (the Joint UK Land Environment Simulator) represents terrestrial processes in the UK Hadley Centre family of models and in the first generation UK Earth System Model. Previously, JULES represented five plant functional types (PFTs): broadleaf trees, needle-leaf trees, C3 and C4 grasses, and shrubs. This study addresses three developments in JULES. First, trees and shrubs were split into deciduous and evergreen PFTs to better represent the range of leaf life spans and metabolic capacities that exists in nature. Second, we distinguished between temperate and tropical broadleaf evergreen trees. These first two changes result in a new set of nine PFTs: tropical and temperate broadleaf evergreen trees, broadleaf deciduous trees, needle-leaf evergreen and deciduous trees, C3 and C4 grasses, and evergreen and deciduous shrubs. Third, using data from the TRY database, we updated the relationship between leaf nitrogen and the maximum rate of carboxylation of Rubisco (Vcmax), and updated the leaf turnover and growth rates to include a trade-off between leaf life span and leaf mass per unit area.Overall, the simulation of gross and net primary productivity (GPP and NPP, respectively) is improved with the nine PFTs when compared to FLUXNET sites, a global GPP data set based on FLUXNET, and MODIS NPP. Compared to the standard five PFTs, the new nine PFTs simulate a higher GPP and NPP, with the exception of C3 grasses in cold environments and C4 grasses that were previously over-productive. On a biome scale, GPP is improved for all eight biomes evaluated and NPP is improved for most biomes - the exceptions being the tropical forests, savannahs, and extratropical mixed forests where simulated NPP is too

75 FR 17692 - Foreign-Trade Zone 82; Application for Subzone Authority; ThyssenKrupp Steel and Stainless USA...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-07

... use FTZ procedures for their operations, the structure of many existing U.S. steel plants could make...; Application for Subzone Authority; ThyssenKrupp Steel and Stainless USA, LLC; Invitation for Public Comment on...Krupp Steel and Stainless USA, LLC (ThyssenKrupp) facility in Calvert, Alabama. The staff's preliminary...

Dissolution of steel slags in aqueous media.

PubMed

Yadav, Shashikant; Mehra, Anurag

2017-07-01

Steel slag is a major industrial waste in steel industries, and its dissolution behavior in water needs to be characterized in the larger context of its potential use as an agent for sequestering CO 2 . For this purpose, a small closed system batch reactor was used to conduct the dissolution of steel slags in an aqueous medium under various dissolution conditions. In this study, two different types of steel slags were procured from steel plants in India, having diverse structural features, mineralogical compositions, and particle sizes. The experiment was performed at different temperatures for 240 h of dissolution at atmospheric pressure. The dissolution rates of major and minor slag elements were quantified through liquid-phase elemental analysis using an inductively coupled plasma atomic emission spectroscopy at different time intervals. Advanced analytical techniques such as field emission gun-scanning electron microscope, energy-dispersive X-ray, BET, and XRD were also used to analyze mineralogical and structural changes in the slag particles. High dissolution of slags was observed irrespective of the particle size distribution, which suggests high carbonation potential. Concentrations of toxic heavy metals in the leachate were far below maximum acceptable limits. Thus, the present study investigates the dissolution behavior of different mineral ions of steel slag in aqueous media in light of its potential application in CO 2 sequestration.

Thermal Aging Phenomena in Cast Duplex Stainless Steels

DOE PAGES

Byun, T. S.; Yang, Y.; Overman, N. R.; ...

2015-11-12

We used cast stainless steels (CASSs)for the large components of light water reactor (LWR) power plants such as primary coolant piping and pump casing. The thermal embrittlement of CASS components is one of the most serious concerns related to the extended-term operation of nuclear power plants. Many past researches have concluded that the formation of Cr-rich alpha-phase by Spinodal decomposition of delta-ferrite phase is the primary mechanism for the thermal embrittlement. Cracking mechanism in the thermally-embrittled duplex stainless steels consists of the formation of cleavage at ferrite and its propagation via separation of ferrite-austenite interphase. This article intends to providemore » an introductory overview on the thermal aging phenomena in LWR-relevant conditions. Firstly, the thermal aging effect on toughness is discussed in terms of the cause of embrittlement and influential parameters. Moreover, an approximate analysis of thermal reaction using Arrhenius equation was carried out to scope the aging temperatures for the accelerated aging experiments to simulate the 60 and 80 years of services. Further, an equilibrium precipitation calculation was performed for model CASS alloys using the CALPHAD program, and the results are used to describe the precipitation behaviors in duplex stainless steels. Our results are also to be used to guide an on-going research aiming to provide knowledge-based conclusive prediction for the integrity of the CASS components of LWR power plants during the service life extended up to and beyond 60 years.« less

Thermal Aging Phenomena in Cast Duplex Stainless Steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Byun, T. S.; Yang, Y.; Overman, N. R.

Cast stainless steels (CASSs) have been extensively used for the large components of light water reactor (LWR) power plants such as primary coolant piping and pump casing. The thermal embrittlement of CASS components is one of the most serious concerns related to the extended-term operation of nuclear power plants. Many past researches have concluded that the formation of Cr–rich α'-phase by Spinodal decomposition of δ-ferrite phase is the primary mechanism for the thermal embrittlement. Cracking mechanism in the thermally-embrittled duplex stainless steels consists of the formation of cleavage at ferrite and its propagation via separation of ferrite-austenite interphase. This articlemore » intends to provide an introductory overview on the thermal aging phenomena in LWR relevant conditions. Firstly, the thermal aging effect on toughness is discussed in terms of the cause of embrittlement and influential parameters. An approximate analysis of thermal reaction using Arrhenius equation was carried out to scope the aging temperatures for the accelerated aging experiments to simulate the 60 and 80 years of services. Further, equilibrium precipitation calculation was performed for model CASS alloys using the CALPHAD program and the results are used to describe the precipitation behaviors in duplex stainless steels. These results are also to be used to guide an on-going research aiming to provide knowledge-based conclusive prediction for the integrity of the CASS components of LWR power plants during the service life extended up to and beyond 60 years.« less

From flint to stainless steel: observations on surgical instrument composition.

PubMed Central

Kirkup, J.

1993-01-01

Man's failure to extract deeply embedded thorns and arrowheads, with bare hands and teeth, stimulated 'instrument substitutes' mimicking these appendages. Evidence from primitive communities suggest animal, plant and mineral items were employed, both before and after metal became the standard material of today's armamentarium. Changing surgical instrument composition has mirrored concurrent technology and manufacturing methods both of which are reviewed. Particular significance is accorded flint, bronze, crucible steel, thermal sterilisation, nickel-plate, stainless steel and disposable plastics. The paper is based on an exhibition From Flint to Stainless Steel on display at the College. Images Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 PMID:8215156

Direct gas-solid carbonation kinetics of steel slag and the contribution to in situ sequestration of flue gas CO(2) in steel-making plants.

PubMed

Tian, Sicong; Jiang, Jianguo; Chen, Xuejing; Yan, Feng; Li, Kaimin

2013-12-01

Direct gas-solid carbonation of steel slag under various operational conditions was investigated to determine the sequestration of the flue gas CO2 . X-ray diffraction analysis of steel slag revealed the existence of portlandite, which provided a maximum theoretical CO2 sequestration potential of 159.4 kg CO 2 tslag (-1) as calculated by the reference intensity ratio method. The carbonation reaction occurred through a fast kinetically controlled stage with an activation energy of 21.29 kJ mol(-1) , followed by 10(3) orders of magnitude slower diffusion-controlled stage with an activation energy of 49.54 kJ mol(-1) , which could be represented by a first-order reaction kinetic equation and the Ginstling equation, respectively. Temperature, CO2 concentration, and the presence of SO2 impacted on the carbonation conversion of steel slag through their direct and definite influence on the rate constants. Temperature was the most important factor influencing the direct gas-solid carbonation of steel slag in terms of both the carbonation conversion and reaction rate. CO2 concentration had a definite influence on the carbonation rate during the kinetically controlled stage, and the presence of SO2 at typical flue gas concentrations enhanced the direct gas-solid carbonation of steel slag. Carbonation conversions between 49.5 % and 55.5 % were achieved in a typical flue gas at 600 °C, with the maximum CO2 sequestration amount generating 88.5 kg CO 2 tslag (-1) . Direct gas-solid carbonation of steel slag showed a rapid CO2 sequestration rate, high CO2 sequestration amounts, low raw-material costs, and a large potential for waste heat utilization, which is promising for in situ carbon capture and sequestration in the steel industry. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Employing the Disadvantaged: Inland Steel's Experience.

ERIC Educational Resources Information Center

Campbell, Ralph

1969-01-01

Among the various approaches used by the Inland Steel Company in training ghetto youth for jobs, greatest promise has been shown by the Work Experience and Training Program initiated in 1965 at the Joseph T. Ryerson and Son plant, an Inland subsidiary located in the Lawndale (West Side) area of Chicago near the scene of the 1966 riots. Results…

4. NHP, Water Turbine Section, showing steel standpipe bases, tailrace ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. NHP, Water Turbine Section, showing steel standpipe bases, tailrace and west wall of Powerhouse Section. View is to the North. - Nunn Hydroelectric Plant, On Madison River, Ennis, Madison County, MT

A Goal Programming Optimization Model for The Allocation of Liquid Steel Production

NASA Astrophysics Data System (ADS)

Hapsari, S. N.; Rosyidi, C. N.

2018-03-01

This research was conducted in one of the largest steel companies in Indonesia which has several production units and produces a wide range of steel products. One of the important products in the company is billet steel. The company has four Electric Arc Furnace (EAF) which produces liquid steel which must be procesed further to be billet steel. The billet steel plant needs to make their production process more efficient to increase the productvity. The management has four goals to be achieved and hence the optimal allocation of the liquid steel production is needed to achieve those goals. In this paper, a goal programming optimization model is developed to determine optimal allocation of liquid steel production in each EAF, to satisfy demand in 3 periods and the company goals, namely maximizing the volume of production, minimizing the cost of raw materials, minimizing maintenance costs, maximizing sales revenues, and maximizing production capacity. From the results of optimization, only maximizing production capacity goal can not achieve the target. However, the model developed in this papare can optimally allocate liquid steel so the allocation of production does not exceed the maximum capacity of the machine work hours and maximum production capacity.

PLAB and UK graduates' performance on MRCP(UK) and MRCGP examinations: data linkage study.

PubMed

McManus, I C; Wakeford, Richard

2014-04-17

To assess whether international medical graduates passing the two examinations set by the Professional and Linguistic Assessments Board (PLAB1 and PLAB2) of the General Medical Council (GMC) are equivalent to UK graduates at the end of the first foundation year of medical training (F1), as the GMC requires, and if not, to assess what changes in the PLAB pass marks might produce equivalence. Data linkage of GMC PLAB performance data with data from the Royal Colleges of Physicians and the Royal College of General Practitioners on performance of PLAB graduates and UK graduates at the MRCP(UK) and MRCGP examinations. Doctors in training for internal medicine or general practice in the United Kingdom. 7829, 5135, and 4387 PLAB graduates on their first attempt at MRCP(UK) Part 1, Part 2, and PACES assessments from 2001 to 2012 compared with 18,532, 14,094, and 14,376 UK graduates taking the same assessments; 3160 PLAB1 graduates making their first attempt at the MRCGP AKT during 2007-12 compared with 14,235 UK graduates; and 1411 PLAB2 graduates making their first attempt at the MRCGP CSA during 2010-12 compared with 6935 UK graduates. Performance at MRCP(UK) Part 1, Part 2, and PACES assessments, and MRCGP AKT and CSA assessments in relation to performance on PLAB1 and PLAB2 assessments, as well as to International English Language Testing System (IELTS) scores. MRCP(UK), MRCGP, and PLAB results were analysed as marks relative to the pass mark at the first attempt. PLAB1 marks were a valid predictor of MRCP(UK) Part 1, MRCP(UK) Part 2, and MRCGP AKT (r=0.521, 0.390, and 0.490; all P<0.001). PLAB2 marks correlated with MRCP(UK) PACES and MRCGP CSA (r=0.274, 0.321; both P<0.001). PLAB graduates had significantly lower MRCP(UK) and MRCGP assessments (Glass's Δ=0.94, 0.91, 1.40, 1.01, and 1.82 for MRCP(UK) Part 1, Part 2, and PACES and MRCGP AKT and CSA), and were more likely to fail assessments and to progress more slowly than UK medical graduates. IELTS scores correlated

PLAB and UK graduates’ performance on MRCP(UK) and MRCGP examinations: data linkage study

PubMed Central

Wakeford, Richard

2014-01-01

Objectives To assess whether international medical graduates passing the two examinations set by the Professional and Linguistic Assessments Board (PLAB1 and PLAB2) of the General Medical Council (GMC) are equivalent to UK graduates at the end of the first foundation year of medical training (F1), as the GMC requires, and if not, to assess what changes in the PLAB pass marks might produce equivalence. Design Data linkage of GMC PLAB performance data with data from the Royal Colleges of Physicians and the Royal College of General Practitioners on performance of PLAB graduates and UK graduates at the MRCP(UK) and MRCGP examinations. Setting Doctors in training for internal medicine or general practice in the United Kingdom. Participants 7829, 5135, and 4387 PLAB graduates on their first attempt at MRCP(UK) Part 1, Part 2, and PACES assessments from 2001 to 2012 compared with 18 532, 14 094, and 14 376 UK graduates taking the same assessments; 3160 PLAB1 graduates making their first attempt at the MRCGP AKT during 2007-12 compared with 14 235 UK graduates; and 1411 PLAB2 graduates making their first attempt at the MRCGP CSA during 2010-12 compared with 6935 UK graduates. Main outcome measures Performance at MRCP(UK) Part 1, Part 2, and PACES assessments, and MRCGP AKT and CSA assessments in relation to performance on PLAB1 and PLAB2 assessments, as well as to International English Language Testing System (IELTS) scores. MRCP(UK), MRCGP, and PLAB results were analysed as marks relative to the pass mark at the first attempt. Results PLAB1 marks were a valid predictor of MRCP(UK) Part 1, MRCP(UK) Part 2, and MRCGP AKT (r=0.521, 0.390, and 0.490; all P<0.001). PLAB2 marks correlated with MRCP(UK) PACES and MRCGP CSA (r=0.274, 0.321; both P<0.001). PLAB graduates had significantly lower MRCP(UK) and MRCGP assessments (Glass’s Δ=0.94, 0.91, 1.40, 1.01, and 1.82 for MRCP(UK) Part 1, Part 2, and PACES and MRCGP AKT and CSA), and were more likely to fail assessments

Chance UK

ERIC Educational Resources Information Center

McGrath, Gracia

2003-01-01

Chance UK is a unique charity in the UK that specialises in mentoring programmes for primary schoolchildren with behavioural problems. It was founded in 1995 by a policeman, Chief Superintendent Paul Mathias, who believed that by stepping in early, young children with behavioural difficulties could be given the chance to develop the necessary…

Detection and evaluation of weld defects in stainless steel using alternating current field measurement

NASA Astrophysics Data System (ADS)

Wei-Li, Ma, Weiping; Pan-Qi, Wen-jiao, Dou; Yuan, Xin'an; Yin, Xiaokang

2018-04-01

Stainless steel is widely used in nuclear power plants, such as various high-radioactive pool, tools storage and fuel transportation channel, and serves as an important barrier to stop the leakage of high-radioactive material. NonDestructive Evaluation (NDE) methods, eddy current testing (ET), ultrasonic examination (UT), penetration testing (PT) and hybrid detection method, etc., have been introduced into the inspection of a nuclear plant. In this paper, the Alternating Current Field Measurement (ACFM) was fully applied to detect and evaluate the defects in the welds of the stainless steel. Simulations were carried out on different defect types, crack lengths, and orientation to reveal the relationship between the signals and dimensions to determine whether methods could be validated by the experiment. A 3-axis ACFM probe was developed and three plates including 16 defects, which served in nuclear plant before, were examined by automatic detection equipment. The result shows that the minimum detectable crack length on the surface is 2mm and ACFM shows excellent inspection results for a weld in stainless steel and gives an encouraging prospect of broader application.

Use of Niobium High Strength Steels with 450 MPA Yield Strength for Construction

NASA Astrophysics Data System (ADS)

Silvestre, Leonardo; Langenberg, Peter; Amaral, Thiago; Carboni, Marcelo; Meira, Marcos; Jordão, Alexandre

This paper presents an actual case of a new industrial building at CBMM's plant in Araxá, Brazil as an example of lean design using microalloyed steels. The structure consists mostly of microalloyed ASTM A572 steel grades 65 and 50 instead of the conventional carbon manganese ASTM A36 steel. The application of grade 65 with more than 450 MPa of yield strength is an innovative solution for this type of construction in South America. A complete welding evaluation performed on the low carbon, niobium microalloyed grade 65 steel showed the welding properties and benefits. Niobium's effect of increasing strength and toughness simultaneously resulted in relevant savings in total steel consumption for the project. The paper also quantifies the expected savings in costs, energy and carbon dioxide emissions.

Automatic Detection of Pearlite Spheroidization Grade of Steel Using Optical Metallography.

PubMed

Chen, Naichao; Chen, Yingchao; Ai, Jun; Ren, Jianxin; Zhu, Rui; Ma, Xingchi; Han, Jun; Ma, Qingqian

2016-02-01

To eliminate the effect of subjective factors during manually determining the pearlite spheroidization grade of steel by analysis of optical metallography images, a novel method combining image mining and artificial neural networks (ANN) is proposed. The four co-occurrence matrices of angular second moment, contrast, correlation, and entropy are adopted to objectively characterize the images. ANN is employed to establish a mathematical model between the four co-occurrence matrices and the corresponding spheroidization grade. Three materials used in coal-fired power plants (ASTM A315-B steel, ASTM A335-P12 steel, and ASTM A355-P11 steel) were selected as the samples to test the validity of our proposed method. The results indicate that the accuracies of the calculated spheroidization grades reach 99.05, 95.46, and 93.63%, respectively. Hence, our newly proposed method is adequate for automatically detecting the pearlite spheroidization grade of steel using optical metallography.

Use of Nitrocarburizing for Strengthening Threaded Joints of Drill Pipes from Medium-Carbon Alloy Steels

NASA Astrophysics Data System (ADS)

Priymak, E. Yu.; Stepanchukova, A. V.; Yakovleva, I. L.; Tereshchenko, N. A.

2015-05-01

Nitrocarburizing is tested at the Drill Equipment Plant for reinforcing threaded joints of drill pipes for units with retrievable core receiver (RCR). The effect of the nitrocarburizing on the mechanical properties of steels of different alloying systems is considered. Steels for the production of threaded joints of drill pipes are recommended.

77 FR 30589 - SteelRiver Infrastructure Partners LP, SteelRiver Infrastructure Associates LLC, SteelRiver...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35622] SteelRiver Infrastructure Partners LP, SteelRiver Infrastructure Associates LLC, SteelRiver Infrastructure Fund North America LP, and Patriot Funding LLC--Control Exemption--Patriot Rail Corp., et al. SteelRiver...

UK-trained junior doctors' intentions to work in UK medicine: questionnaire surveys, three years after graduation

PubMed Central

Surman, Geraldine; Goldacre, Michael J

2017-01-01

Objective To report on the career intentions, three years after qualification, of 12 national cohorts of UK-trained doctors who qualified between 1974 and 2012, and, specifically, to compare recent UK medical graduates’ intentions to work in medicine in the UK with earlier graduates. Design Questionnaire surveys of cohorts of UK medical graduates defined by year of graduation. Setting UK. Participants 30,272 UK medical graduates. Main outcome measures Stated level of intention to pursue a long-term career in medicine in the UK. Results The response rate was 62% (30,272/48,927). We examined responses to the question ‘Apart from temporary visits abroad, do you intend to practise medicine in the United Kingdom for the foreseeable future?' Of doctors from UK homes, 90% had specified that they would ‘definitely or probably’ practise medicine in the UK in the surveys of 1977–1986, 81% in 1996–2011 and 64% in 2015. Those who said that they would probably or definitely not practise medicine in the UK comprised 5% in 1977–1986, 8% in 1996–2011 and 15% in 2015. Most who were not definite about a future career in UK medicine indicated that they would wish to practise medicine outside the UK rather than to leave medicine. Conclusions The wish to remain in UK medical practice in the 2015 survey was unprecedentedly low in this unique series of 40 years of surveys. PMID:29116902

UK-trained junior doctors' intentions to work in UK medicine: questionnaire surveys, three years after graduation.

PubMed

Surman, Geraldine; Goldacre, Michael J; Lambert, Trevor W

2017-12-01

Objective To report on the career intentions, three years after qualification, of 12 national cohorts of UK-trained doctors who qualified between 1974 and 2012, and, specifically, to compare recent UK medical graduates' intentions to work in medicine in the UK with earlier graduates. Design Questionnaire surveys of cohorts of UK medical graduates defined by year of graduation. Setting UK. Participants 30,272 UK medical graduates. Main outcome measures Stated level of intention to pursue a long-term career in medicine in the UK. Results The response rate was 62% (30,272/48,927). We examined responses to the question ' Apart from temporary visits abroad, do you intend to practise medicine in the United Kingdom for the foreseeable future?' Of doctors from UK homes, 90% had specified that they would 'definitely or probably' practise medicine in the UK in the surveys of 1977-1986, 81% in 1996-2011 and 64% in 2015. Those who said that they would probably or definitely not practise medicine in the UK comprised 5% in 1977-1986, 8% in 1996-2011 and 15% in 2015. Most who were not definite about a future career in UK medicine indicated that they would wish to practise medicine outside the UK rather than to leave medicine. Conclusions The wish to remain in UK medical practice in the 2015 survey was unprecedentedly low in this unique series of 40 years of surveys.

Design Optimization of Microalloyed Steels Using Thermodynamics Principles and Neural-Network-Based Modeling

NASA Astrophysics Data System (ADS)

Mohanty, Itishree; Chintha, Appa Rao; Kundu, Saurabh

2018-06-01

The optimization of process parameters and composition is essential to achieve the desired properties with minimal additions of alloying elements in microalloyed steels. In some cases, it may be possible to substitute such steels for those which are more richly alloyed. However, process control involves a larger number of parameters, making the relationship between structure and properties difficult to assess. In this work, neural network models have been developed to estimate the mechanical properties of steels containing Nb + V or Nb + Ti. The outcomes have been validated by thermodynamic calculations and plant data. It has been shown that subtle thermodynamic trends can be captured by the neural network model. Some experimental rolling data have also been used to support the model, which in addition has been applied to calculate the costs of optimizing microalloyed steel. The generated pareto fronts identify many combinations of strength and elongation, making it possible to select composition and process parameters for a range of applications. The ANN model and the optimization model are being used for prediction of properties in a running plant and for development of new alloys, respectively.

Exposure to air pollution near a steel plant is associated with reduced heart rate variability: a randomised crossover study.

PubMed

Shutt, Robin H; Kauri, Lisa Marie; Weichenthal, Scott; Kumarathasan, Premkumari; Vincent, Renaud; Thomson, Errol M; Liu, Ling; Mahmud, Mamun; Cakmak, Sabit; Dales, Robert

2017-01-28

Epidemiological studies have shown that as ambient air pollution (AP) increases the risk of cardiovascular mortality also increases. The mechanisms of this effect may be linked to alterations in autonomic nervous system function. We wished to examine the effects of industrial AP on heart rate variability (HRV), a measure of subtle changes in heart rate and rhythm representing autonomic input to the heart. Sixty healthy adults were randomized to spend five consecutive 8-h days outdoors in one of two locations: (1) adjacent to a steel plant in the Bayview neighbourhood in Sault Ste Marie Ontario or (2) at a College campus, several kilometers from the plant. Following a 9-16 day washout period, participants spent five consecutive days at the other site. Ambient AP levels and ambulatory electrocardiogram recordings were collected daily. HRV analysis was undertaken on a segment of the ambulatory ECG recording during a 15 min rest period, near the end of the 8-h on-site day. Standard HRV parameters from both time and frequency domains were measured. Ambient AP was measured with fixed site monitors at both sites. Statistical analysis was completed using mixed-effects models. Compared to the College site, HRV was statistically significantly reduced at the Bayview site by 13% (95%CI 3.6,19.2) for the standard deviation of normal to normal, 8% (95%CI 0.1, 4.9) for the percent normal to normal intervals differing by more than 50 ms, and 15% (95%CI 74.9, 571.2) for low frequency power. Levels of carbon monoxide, sulphur dioxide, nitrogen dioxide, and fine and ultrafine particulates were slightly, but statistically significantly, elevated at Bayview when compared to College. Interquartile range changes in individual air pollutants were significantly associated with reductions in HRV measured on the same day. The patterns of effect showed a high degree of consistency, with nearly all pollutants significantly inversely associated with at least one measure of HRV. The significant

13. Building H9; view of stainless steel probes and vacuum ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. Building H-9; view of stainless steel probes and vacuum line, looking W. (Ryan and Harms) - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

NASA Astrophysics Data System (ADS)

Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

2015-07-01

The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

Promoting SETI in the UK

NASA Astrophysics Data System (ADS)

Penny, Alan

2013-10-01

MEETING REPORT What does the UK presently do in the search for extraterrestrial intelligence and what are the plans for the future? Alan Penny reports on a meeting of UK academics active in SETI, held as sessions in the recent National Astronomy Meeting in Scotland - and the formation of the UK SETI Research Network to promote UK academic work.

Design and implementation of ergonomic performance measurement system at a steel plant in India.

PubMed

Ray, Pradip Kumar; Tewari, V K

2012-01-01

Management of Tata Steel, the largest steel making company of India in the private sector, felt the need to develop a framework to determine the levels of ergonomic performance at its different workplaces. The objectives of the study are manifold: to identify and characterize the ergonomic variables for a given worksystem with regard to work efficiency, operator safety, and working conditions, to design a comprehensive Ergonomic Performance Indicator (EPI) for quantitative determination of the ergonomic status and maturity of a given worksystem. The study team of IIT Kharagpur consists of three faculty members and the management of Tata Steel formed a team of eleven members for implementation of EPI model. In order to design and develop the EPI model with total participation and understanding of the concerned personnel of Tata Steel, a three-phase action plan for the project was prepared. The project consists of three phases: preparation and data collection, detailed structuring and validation of EPI model. Identification of ergonomic performance factors, development of interaction matrix, design of assessment tool, and testing and validation of assessment tool (EPI) in varied situations are the major steps in these phases. The case study discusses in detail the EPI model and its applications.

72. SECOND FLOOR, HEATER ROOM ENTRANCE (UPPER RIGHT) AND STEEL, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

72. SECOND FLOOR, HEATER ROOM ENTRANCE (UPPER RIGHT) AND STEEL, CONCRETE, BRICK, AND SPRING AIR CONDITIONER BASE, BAY 31-32/4 SOUTH, TO WEST - Ford Motor Company Edgewater Assembly Plant, Assembly Building, 309 River Road, Edgewater, Bergen County, NJ

Inhibitive effect of Xylopia ferruginea extract on the corrosion of mild steel in 1M HCl medium

NASA Astrophysics Data System (ADS)

Raja, Pandian Bothi; Rahim, Afidah Abdul; Osman, Hasnah; Awang, Khalijah

2011-08-01

The alkaloid content of the leaves and stem bark of Xylopia ferruginea plant was isolated and tested for its anticorrosion potential on mild steel corrosion in a hydrochloric acid medium by using electrochemical impedance spectroscopy, potentiodynamic polarization measurement, scanning electron microscopy (SEM), and Fourier transform infra red (FTIR) analysis. The experimental results reveal the effective anticorrosion potential of the plant extract. The mixed mode of action exhibited by the plant extract is evidenced from the polarization study. SEM images proof the formation of a protective layer over the mild steel surface, and this is supported by the FTIR study. The possible mode of the corrosion inhibition mechanism has also been discussed.

Developing the radiation protection safety culture in the UK.

PubMed

Cole, P; Hallard, R; Broughton, J; Coates, R; Croft, J; Davies, K; Devine, I; Lewis, C; Marsden, P; Marsh, A; McGeary, R; Riley, P; Rogers, A; Rycraft, H; Shaw, A

2014-06-01

In the UK, as elsewhere, there is potential to improve how radiological challenges are addressed through improvement in, or development of, a strong radiation protection (RP) safety culture. In preliminary work in the UK, two areas have been identified as having a strong influence on UK society: the healthcare and nuclear industry sectors. Each has specific challenges, but with many overlapping common factors. Other sectors will benefit from further consideration.In order to make meaningful comparisons between these two principal sectors, this paper is primarily concerned with cultural aspects of RP in the working environment and occupational exposures rather than patient doses.The healthcare sector delivers a large collective dose to patients each year, particularly for diagnostic purposes, which continues to increase. Although patient dose is not the focus, it must be recognised that collective patient dose is inevitably linked to collective occupational exposure, especially in interventional procedures.The nuclear industry faces major challenges as work moves from operations to decommissioning on many sites. This involves restarting work in the plants responsible for the much higher radiation doses of the 1960/70s, but also performing tasks that are considerably more difficult and hazardous than those original performed in these plants.Factors which influence RP safety culture in the workplace are examined, and proposals are considered for a series of actions that may lead to an improvement in RP culture with an associated reduction in dose in many work areas. These actions include methods to improve knowledge and awareness of radiation safety, plus ways to influence management and colleagues in the workplace. The exchange of knowledge about safety culture between the nuclear industry and medical areas may act to develop RP culture in both sectors, and have a wider impact in other sectors where exposures to ionising radiations can occur.

Aircraft Steels

DTIC Science & Technology

2009-02-19

component usage. PH 13-8Mo is a precipitation-hardenable martensitic stainless steel combining excellent corrosion resistance with strength. Custom 465 is...a martensitic , age-hardenable stainless steel capable of about 1,724 MPa (250 ksi) UTS when peak-aged (H900 condition). Especially, this steel can...NOTES 14. ABSTRACT Five high strength steels (4340, 300M, AerMet 100, Ferrium S53, and Hy-Tuf) and four stainless steels (High Nitrogen, 13

4. DETAIL VIEW (SIDE A) OF HANDMADE STEEL BOX ASSOCIATED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. DETAIL VIEW (SIDE A) OF HANDMADE STEEL BOX ASSOCIATED WITH THE DEPLETED URANIUM ALLOY DEVELOPMENT AND COMPONENT FABRICATION PROCESS. THE BOX WAS USED TO TRANSFER HEATED BLOCKS OF METAL (SHOWN IN THE OPENED DOOR) FROM THE MOLTEN SALT BATH TO THE ROLLER LINES. (4/28/62) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

CONSTRUCTION PROGRESS PHOTO SHOWING EMPLACEMENT STEEL BEAMS FUEL STORAGE BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CONSTRUCTION PROGRESS PHOTO SHOWING EMPLACEMENT STEEL BEAMS FUEL STORAGE BUILDING (CPP-603) LOOKING EAST. INL PHOTO NUMBER NRTS-51-1371. Unknown Photographer, 1/31/1951 - Idaho National Engineering Laboratory, Idaho Chemical Processing Plant, Fuel Reprocessing Complex, Scoville, Butte County, ID

Microbiological corrosion of ASTM SA105 carbon steel pipe for industrial fire water usage

NASA Astrophysics Data System (ADS)

Chidambaram, S.; Ashok, K.; Karthik, V.; Venkatakrishnan, P. G.

2018-02-01

The large number of metallic systems developed for last few decades against both general uniform corrosion and localized corrosion. Among all microbiological induced corrosion (MIC) is attractive, multidisciplinary and complex in nature. Many chemical processing industries utilizes fresh water for fire service to nullify major/minor fire. One such fire water service line pipe attacked by micro-organisms leads to leakage which is industrially important from safety point of view. Also large numbers of leakage reported in similar fire water service of nearby food processing plant, paper & pulp plant, steel plant, electricity board etc…In present investigation one such industrial fire water service line failure analysis of carbon steel line pipe was analyzed to determine the cause of failure. The water sample subjected to various chemical and bacterial analyses. Turbidity, pH, calcium hardness, free chlorine, oxidation reduction potential, fungi, yeasts, sulphide reducing bacteria (SRB) and total bacteria (TB) were measured on water sample analysis. The corrosion rate was measured on steel samples and corrosion coupon measurements were installed in fire water for validating non flow assisted localized corrosion. The sulphide reducing bacteria (SRB) presents in fire water causes a localized micro biological corrosion attack of line pipe.

Development of Custom 465® Corrosion-Resisting Steel for Landing Gear Applications

NASA Astrophysics Data System (ADS)

Daymond, Benjamin T.; Binot, Nicolas; Schmidt, Michael L.; Preston, Steve; Collins, Richard; Shepherd, Alan

2016-04-01

Existing high-strength low-alloy steels have been in place on landing gear for many years owing to their superior strength and cost performance. However, there have been major advances in improving the strength of high-performance corrosion-resisting steels. These materials have superior environmental robustness and remove the need for harmful protective coatings such as chromates and cadmium now on the list for removal under REACH legislation. A UK government-funded collaborative project is underway targeting a refined specification Custom 465® precipitation hardened stainless steel to replace the current material on Airbus A320 family aircraft main landing gear, a main fitting component developed by Messier-Bugatti-Dowty. This is a collaborative project between Airbus, Messier-Bugatti-Dowty, and Carpenter Technology Corporation. An extensive series of coupon tests on four production Heats of the material have been conducted, to obtain a full range of mechanical, fatigue, and corrosion properties. Custom 465® is an excellent replacement to the current material, with comparable tensile strength and fracture toughness, better ductility, and very good general corrosion and stress corrosion cracking resistance. Fatigue performance is the only significant area of deficit with respect to incumbent materials, fatigue initiation being often related to carbo-titanium-nitride particles and cleavage zones.

Performance of the JULES land surface model for UK Biogenic VOC emissions

NASA Astrophysics Data System (ADS)

Hayman, Garry; Comyn-Platt, Edward; Vieno, Massimo; Langford, Ben

2017-04-01

Emissions of biogenic non-methane volatile organic compounds (NMVOCs) are important for air quality and tropospheric composition. Through their contribution to the production of tropospheric ozone and secondary organic aerosol (SOA), biogenic VOCs indirectly contribute to climate forcing and climate feedbacks [1]. Biogenic VOCs encompass a wide range of compounds and are produced by plants for growth, development, reproduction, defence and communication [2]. There are both biological and physico-chemical controls on emissions [3]. Only a few of the many biogenic VOCs are of wider interest and only two or three (isoprene and the monoterpenes, α- and β-pinene) are represented in chemical transport models. We use the Joint UK Land Environment Simulator (JULES), the UK community land surface model, to estimate biogenic VOC emission fluxes. JULES is a process-based model that describes the water, energy and carbon balances and includes temperature, moisture and carbon stores [4, 5]. JULES currently provides emission fluxes of the 4 largest groups of biogenic VOCs: isoprene, terpenes, methanol and acetone. The JULES isoprene scheme uses gross primary productivity (GPP), leaf internal carbon and the leaf temperature as a proxy for the electron requirement for isoprene synthesis [6]. In this study, we compare JULES biogenic VOC emission estimates of isoprene and terepenes with (a) flux measurements made at selected sites in the UK and Europe and (b) gridded estimates for the UK from the EMEP/EMEP4UK atmospheric chemical transport model [7, 8], using site-specific or EMEP4UK driving meteorological data, respectively. We compare the UK-scale emission estimates with literature estimates. We generally find good agreement in the comparisons but the estimates are sensitive to the choice of the base or reference emission potentials. References (1) Unger, 2014: Geophys. Res. Lett., 41, 8563, doi:10.1002/2014GL061616; (2) Laothawornkitkul et al., 2009: New Phytol., 183, 27, doi

Energy efficiency technologies in cement and steel industry

NASA Astrophysics Data System (ADS)

Zanoli, Silvia Maria; Cocchioni, Francesco; Pepe, Crescenzo

2018-02-01

In this paper, Advanced Process Control strategies aimed at energy efficiency achievement and improvement in cement and steel industry are proposed. A flexible and smart control structure constituted by several functional modules and blocks has been developed. The designed control strategy is based on Model Predictive Control techniques, formulated on linear models. Two industrial control solutions have been developed, oriented to energy efficiency and process control improvement in cement industry clinker rotary kilns (clinker production phase) and in steel industry billets reheating furnaces. Tailored customization procedures for the design of ad hoc control systems have been executed, based on the specific needs and specifications of the analysed processes. The installation of the developed controllers on cement and steel plants produced significant benefits in terms of process control which resulted in working closer to the imposed operating limits. With respect to the previous control systems, based on local controllers and/or operators manual conduction, more profitable configurations of the crucial process variables have been provided.

Antibacterial effect of silver nanofilm modified stainless steel surface

NASA Astrophysics Data System (ADS)

Fang, F.; Kennedy, J.; Dhillon, M.; Flint, S.

2015-03-01

Bacteria can attach to stainless steel surfaces, resulting in the colonization of the surface known as biofilms. The release of bacteria from biofilms can cause contamination of food such as dairy products in manufacturing plants. This study aimed to modify stainless steel surfaces with silver nanofilms and to examine the antibacterial effectiveness of the modified surface. Ion implantation was applied to produce silver nanofilms on stainless steel surfaces. 35 keV Ag ions were implanted with various fluences of 1 × 1015 to 1 × 1017 ions•cm-2 at room temperature. Representative atomic force microscopy characterizations of the modified stainless steel are presented. Rutherford backscattering spectrometry spectra revealed the implanted atoms were located in the near-surface region. Both unmodified and modified stainless steel coupons were then exposed to two types of bacteria, Pseudomonas fluorescens and Streptococcus thermophilus, to determine the effect of the surface modification on bacterial attachment and biofilm development. The silver modified coupon surface fluoresced red over most of the surface area implying that most bacteria on coupon surface were dead. This study indicates that the silver nanofilm fabricated by the ion implantation method is a promising way of reducing the attachment of bacteria and delay biofilm formation.

5. NHP, Water Turbine Section, southernmost steel standpipe base with ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. NHP, Water Turbine Section, southern-most steel standpipe base with concrete curbing, constructed in 1908-1909, and turbine shaft entry portals in west wall of Powerhouse Section. View is to the Northeast. - Nunn Hydroelectric Plant, On Madison River, Ennis, Madison County, MT

6. NHP, Water Turbine Section, northernmost steel standpipe base with ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. NHP, Water Turbine Section, northern-most steel standpipe base with concrete curbing, constructed in 1908-1909, and turbine shaft entry portal in west wall of Powerhouse Section. View is to the Northeast. - Nunn Hydroelectric Plant, On Madison River, Ennis, Madison County, MT

Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels

NASA Astrophysics Data System (ADS)

Brusewicz, Krzysztof; Sterpejkowicz-Wersocki, Witold; Jankowski, Robert

2017-06-01

With the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steelwater locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including earthquakes, may also occur in our country, although their incidence is relatively low. However, given the unpredictable nature of such events, as well as serious consequences they might cause, the study of the seismic resistance of the steel water gate, as one of the most vulnerable elements of a hydroelectric power plant, seems to be important. In this study, a steel radial gate has been analyzed. As far as water gates are concerned, it is among the most popular solutions because of its relatively small weight, compared to plain gates. A modal analysis of the steel radial gate was conducted with the use of the FEM in the ABAQUS software. All structural members were modelled using shell elements with detailed geometry representing a real structure.Water was modelled as an added mass affecting the structure. Different water levels were used to determine the most vulnerable state of the working steel water gate. The results of the modal analysis allowed us to compare the frequencies and their eigenmodes in response to different loads, which is one of the first steps in researching the dynamic properties of steel water gates and their behaviour during extreme dynamic loads, including earthquakes.

Lightweight steel tidal power barrages with minimal environmental impact: application to the Severn Barrage.

PubMed

Rainey, R C T

2018-01-01

For tidal power barrages, a breast-shot water wheel, with a hydraulic transmission, has significant advantages over a conventional Kaplan turbine. It is better suited to combined operations with pumping that maintain the tidal range upstream of the barrage (important in reducing the environmental impact), and is much less harmful to fish. It also does not require tapered entry and exit ducts, making the barrage much smaller and lighter, so that it can conveniently be built in steel. For the case of the Severn Estuary, UK, it is shown that a barrage at Porlock would generate an annual average power of 4 GW (i.e. 35 TWh yr -1 ), maintain the existing tidal ranges upstream of it and reduce the tidal ranges downstream of it by only about 10%. The weight of steel required, in relation to the annual average power generated, compares very favourably with a recent offshore wind farm.

Lightweight steel tidal power barrages with minimal environmental impact: application to the Severn Barrage

NASA Astrophysics Data System (ADS)

Rainey, R. C. T.

2018-01-01

For tidal power barrages, a breast-shot water wheel, with a hydraulic transmission, has significant advantages over a conventional Kaplan turbine. It is better suited to combined operations with pumping that maintain the tidal range upstream of the barrage (important in reducing the environmental impact), and is much less harmful to fish. It also does not require tapered entry and exit ducts, making the barrage much smaller and lighter, so that it can conveniently be built in steel. For the case of the Severn Estuary, UK, it is shown that a barrage at Porlock would generate an annual average power of 4 GW (i.e. 35 TWh yr-1), maintain the existing tidal ranges upstream of it and reduce the tidal ranges downstream of it by only about 10%. The weight of steel required, in relation to the annual average power generated, compares very favourably with a recent offshore wind farm.

Air quality assessment of benzo(a)pyrene from asphalt plant operation.

PubMed

Gibson, Nigel; Stewart, Robert; Rankin, Erika

2012-01-01

A study has been carried out to assess the contribution of Polycyclic Aromatic Hydrocarbons (PAHs) from asphalt plant operation, utilising Benzo(a)pyrene (BaP) as a marker for PAHs, to the background air concentration around asphalt plants in the UK. The purpose behind this assessment was to determine whether the use of published BaP emission factors based on the US Environmental Protection Agency (EPA) methodology is appropriate in the context of the UK, especially as the EPA methodology does not give BaP emission factors for all activities. The study also aimed to improve the overall understanding of BaP emissions from asphalt plants in the UK, and determine whether site location and operation is likely to influence the contribution of PAHs to ambient air quality. In order to establish whether the use of US EPA emissions factors is appropriate, the study has compared the BaP emissions measured and calculated emissions rates from two UK sites with those estimated using US EPA emission factors. A dispersion modelling exercise was carried out to show the BaP contribution to ambient air around each site. This study showed that, as the US EPA methodology does not provide factors for all emission sources on asphalt plants, their use may give rise to over- or under-estimations, particularly where sources of BaP are temperature dependent. However, the contribution of both the estimated and measured BaP concentrations to environmental concentration were low, averaging about 0.05 ng m(-3) at the boundary of the sites, which is well below the UK BaP assessment threshold of 0.25 ng m(-3). Therefore, BaP concentrations, and hence PAH concentrations, from similar asphalt plant operations are unlikely to contribute negatively to ambient air quality.

A case study of machinery maintenance protocols and procedures within the UK utilities sector.

PubMed

Edwards, David J; Love, Peter E D

2016-08-01

Failure to conduct periodic fixed-time-to (or scheduled) maintenance on off-highway plant and equipment represents a significant health and safety hazard and major litigation risk for utility contractors completing service excavation and reinstatement works on public highways. Mini-excavators are a ubiquitous mobile plant item used for such tasks and have recently been responsible for several major injuries and fatalities involving workers and members of the public in the United Kingdom (UK). The research utilises the method of triangulation to examine the maintenance practices of utility contractors in the UK. Findings from the research reveal that a combination of prevailing market forces and internal 'company' pressures have inadvertently removed knowledgeable and trained operators, site foremen and managerial supervisors from hands-on maintenance inspections. Rather, 'virtual' maintenance protocols and procedures are adopted by head office but rarely fully implemented on-site. The research concludes with pragmatic recommendations and direction for future research. Copyright © 2015 Elsevier Ltd. All rights reserved.

1. GENERAL EXTERIOR VIEW OF THE ELECTRIC FURNACE STEELMAKING PLANT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. GENERAL EXTERIOR VIEW OF THE ELECTRIC FURNACE STEELMAKING PLANT LOOKING NORTHEAST. - U.S. Steel Duquesne Works, Electric Furnace Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

The experimental verification on the shear bearing capacity of exposed steel column foot

NASA Astrophysics Data System (ADS)

Xijin, LIU

2017-04-01

In terms of the shear bearing capacity of the exposed steel column foot, there are many researches both home and abroad. However, the majority of the researches are limited to the theoretical analysis sector and few of them make the experimental analysis. In accordance with the prototype of an industrial plant in Beijing, this paper designs the experimental model. The experimental model is composed of six steel structural members in two groups, with three members without shear key and three members with shear key. The paper checks the shear bearing capacity of two groups respectively under different axial forces. The experiment shows: The anchor bolt of the exposed steel column foot features relatively large shear bearing capacity which could not be neglected. The results deducted through calculation methods proposed by this paper under two situations match the experimental results in terms of the shear bearing capacity of the steel column foot. Besides, it also proposed suggestions on revising the Code for Design of Steel Structure in the aspect of setting the shear key in the steel column foot.

GENERAL VIEW OF WESTERN PART OF PLANT INCLUDING (LEFT TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

GENERAL VIEW OF WESTERN PART OF PLANT INCLUDING (LEFT TO RIGHT) BETHLEHEM RAIL MILL, GENERAL OFFICE BUILDING, MACHINE SHOP, BAR MILL, BLOOMING MILL & OPEN HEARTH PLANT. - Pittsburgh Steel Company, Monessen Works, Open Hearth Plant, Donner Avenue, Monessen, Westmoreland County, PA

Toughness of 2,25Cr-1Mo steel and weld metal

NASA Astrophysics Data System (ADS)

Acarer, Mustafa; Arici, Gökhan; Acar, Filiz Kumdali; Keskinkilic, Selcuk; Kabakci, Fikret

2017-09-01

2,25Cr-1Mo steel is extensively used at elevated temperature structural applications in fossil fire power plants for steam pipes, nozzle chambers and petrochemical industry for hydrocracking unit due to its excellent creep resistance and good redundant to oxidation. Also they should have acceptable weldability and toughness. The steels are supplied in quenched and tempered condition and their welded components are subjected to post-weld heat treatment (PWHT). Tempering process is carried out at 690-710°C to improve toughness properties. However they are sensitive to reheat cracking and temper embrittlement. To measure temper embrittlement of the steels and their weld metal, temper embrittlement factor and formula (J factor - Watanabe and X formula- Bruscato) are used. Step cooling heat treatment is also applied to determine temper embrittlement. In this study, toughness properties of Cr Mo (W) steels were reviewed. Also transition temperature curves of 2,25Cr-1Mo steel and its weld metal were constructed before and after step cool heat treatment as experimental study. While 2,25Cr-1Mo steel as base metal was supplied, all weld metal samples were produced in Gedik Welding Company. Hardness measurements and microstructure evaluation were also carried out.

Source apportionment of aerosol particles near a steel plant by electron microscopy.

PubMed

Ebert, Martin; Müller-Ebert, Dörthe; Benker, Nathalie; Weinbruch, Stephan

2012-12-01

The size, morphology and chemical composition of 37,715 individual particles collected over 22 sampling days in the vicinity of a large integrated steel production were studied by scanning and transmission electron microscopy. Based on the morphology, chemistry and beam stability the particles were classified into the following fourteen groups: silicates, sea salt, calcium sulfates, calcium carbonates, carbonate-silicate mixtures, sulfate-silicate mixtures, iron oxides, iron mixtures, metal oxide-metals, complex secondary particles, soot, Cl-rich particles, P-rich particles, and other particles. The majority of iron oxide (≈85%) and metal oxide-metal (≈70%) particles as well as ≈20% of the silicate particles are fly ashes from high temperature processes. The emissions from the steel work are dominated by iron oxide particles. For source apportionment, seven source categories and two sectors of local wind direction (industrial and urban background) were distinguished. In both sectors PM₁₀ consists of four major source categories: 35% secondary, 20% industrial, 17% soil and 16% soot in the urban background sector compared to 45% industrial, 20% secondary, 13% soil, and 9% soot in the industrial sector. As the secondary and the soot components are higher in the urban background sector than in the industrial sector, it is concluded that both components predominantly originate from urban background sources (traffic, coal burning, and domestic heating). Abatement measures should not only focus on the steel work but should also include the urban background aerosol.

The research on delayed fracture behavior of high-strength bolts in steel structure

NASA Astrophysics Data System (ADS)

Li, Guo dong; Li, Nan

2017-07-01

High-strength bolts have been widely used in power plants. However, the high-strength bolts which being employed in pumping station, steel structure and pipeline anti-whip structure have been found delayed fracture for many times in a power plant, this will affect the reliability of steel fracture and bring blow risk caused by falling objects. The high-strength bolt with delayed fracture was carried out fracture analysis, metallurgical analysis, chemical analysis, mechanical analysis, as well as bolts installation analysis, it can be comprehensively confirmed that the direct cause of high-strength bolts delayed fracture is the stress corrosion, and the root cause of high-strength bolts delayed fracture should be the improper installation at the initial and the imperfect routine anti-corrosion maintenance.

74. Neg. No. F116A, May 22, 1931, INTERIORPRESSED STEEL BUILDING, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

74. Neg. No. F-116A, May 22, 1931, INTERIOR-PRESSED STEEL BUILDING, SHOWING FENDER CRATE - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

Advances in Energy Conservation of China Steel Industry

PubMed Central

Sun, Wenqiang; Cai, Jiuju; Ye, Zhu

2013-01-01

The course, technical progresses, and achievements of energy conservation of China steel industry (CSI) during 1980–2010 were summarized. Then, the paper adopted e-p method to analyze the variation law and influencing factors of energy consumptions of large- and medium-scale steel plants within different stages. It is pointed out that energy consumption per ton of crude steel has been almost one half lower in these thirty years, with 60% as direct energy conservation owing to the change of process energy consumption and 40% as indirect energy conservation attributed to the adjustment of production structure. Next, the latest research progress of some key common technologies in CSI was introduced. Also, the downtrend of energy consumption per ton of crude steel and the potential energy conservation for CSI during 2011–2025 were forecasted. Finally, it is indicated that the key topic of the next 15 years' research on the energy conservation of CSI is the synergistic operation of material flow and energy flow. It could be achieved by the comprehensive study on energy flow network optimization, such as production, allocation, utilization, recovery, reuse, and resource, according to the energy quantity, quality, and user demand following the first and second laws of thermodynamics. PMID:23533344

Advances in energy conservation of China steel industry.

PubMed

Sun, Wenqiang; Cai, Jiuju; Ye, Zhu

2013-01-01

The course, technical progresses, and achievements of energy conservation of China steel industry (CSI) during 1980-2010 were summarized. Then, the paper adopted e-p method to analyze the variation law and influencing factors of energy consumptions of large- and medium-scale steel plants within different stages. It is pointed out that energy consumption per ton of crude steel has been almost one half lower in these thirty years, with 60% as direct energy conservation owing to the change of process energy consumption and 40% as indirect energy conservation attributed to the adjustment of production structure. Next, the latest research progress of some key common technologies in CSI was introduced. Also, the downtrend of energy consumption per ton of crude steel and the potential energy conservation for CSI during 2011-2025 were forecasted. Finally, it is indicated that the key topic of the next 15 years' research on the energy conservation of CSI is the synergistic operation of material flow and energy flow. It could be achieved by the comprehensive study on energy flow network optimization, such as production, allocation, utilization, recovery, reuse, and resource, according to the energy quantity, quality, and user demand following the first and second laws of thermodynamics.

Update on the Status of Bemisia tabaci in the UK and the Use of Entomopathogenic Fungi within Eradication Programmes

PubMed Central

Cuthbertson, Andrew G. S.

2013-01-01

The sweetpotato whitefly Bemisia tabaci (Gennadius) (Hemiptera: Aleyrodidae) continues to be a serious threat to crops worldwide. The UK holds Protected Zone status against this pest and, as a result, B. tabaci entering on plant material is subjected to a policy of eradication. Both B and Q Bemisia biotypes are now regularly intercepted entering the UK. With increasing reports of neonicotinoid resistance in both these biotypes, it is becoming more problematic to control/eradicate. Therefore, alternative means of control are necessary. Entomopathogenic fungi (Lecanicilllium muscarium and Beauveria bassiana) offer much potential as control agents of B. tabaci within eradication programmes in the UK. PMID:26464385

Nickel: makes stainless steel strong

USGS Publications Warehouse

Boland, Maeve A.

2012-01-01

Nickel is a silvery-white metal that is used mainly to make stainless steel and other alloys stronger and better able to withstand extreme temperatures and corrosive environments. Nickel was first identified as a unique element in 1751 by Baron Axel Fredrik Cronstedt, a Swedish mineralogist and chemist. He originally called the element kupfernickel because it was found in rock that looked like copper (kupfer) ore and because miners thought that "bad spirits" (nickel) in the rock were making it difficult for them to extract copper from it. Approximately 80 percent of the primary (not recycled) nickel consumed in the United States in 2011 was used in alloys, such as stainless steel and superalloys. Because nickel increases an alloy's resistance to corrosion and its ability to withstand extreme temperatures, equipment and parts made of nickel-bearing alloys are often used in harsh environments, such as those in chemical plants, petroleum refineries, jet engines, power generation facilities, and offshore installations. Medical equipment, cookware, and cutlery are often made of stainless steel because it is easy to clean and sterilize. All U.S. circulating coins except the penny are made of alloys that contain nickel. Nickel alloys are increasingly being used in making rechargeable batteries for portable computers, power tools, and hybrid and electric vehicles. Nickel is also plated onto such items as bathroom fixtures to reduce corrosion and provide an attractive finish.

Mercury mass flow in iron and steel production process and its implications for mercury emission control.

PubMed

Wang, Fengyang; Wang, Shuxiao; Zhang, Lei; Yang, Hai; Gao, Wei; Wu, Qingru; Hao, Jiming

2016-05-01

The iron and steel production process is one of the predominant anthropogenic sources of atmospheric mercury emissions worldwide. In this study, field tests were conducted to study mercury emission characteristics and mass flows at two iron and steel plants in China. It was found that low-sulfur flue gas from sintering machines could contribute up to 41% of the total atmospheric mercury emissions, and desulfurization devices could remarkably help reduce the emissions. Coal gas burning accounted for 17%-49% of the total mercury emissions, and therefore the mercury control of coal gas burning, specifically for the power plant burning coal gas to generate electricity, was significantly important. The emissions from limestone and dolomite production and electric furnaces can contribute 29.3% and 4.2% of the total mercury emissions from iron and steel production. More attention should be paid to mercury emissions from these two processes. Blast furnace dust accounted for 27%-36% of the total mercury output for the whole iron and steel production process. The recycling of blast furnace dust could greatly increase the atmospheric mercury emissions and should not be conducted. The mercury emission factors for the coke oven, sintering machine and blast furnace were 0.039-0.047gHg/ton steel, and for the electric furnace it was 0.021gHg/ton steel. The predominant emission species was oxidized mercury, accounting for 59%-73% of total mercury emissions to air. Copyright © 2016. Published by Elsevier B.V.

High temperature oxidation in boiler environment of chromized steel

NASA Astrophysics Data System (ADS)

Alia, F. F.; Kurniawan, T.; Asmara, Y. P.; Ani, M. H. B.; Nandiyanto, A. B. D.

2017-10-01

The demand for increasing efficiency has led to the development and construction of higher operating temperature power plant. This condition may lead to more severe thickness losses in boiler tubes due to excessive corrosion process. Hence, the research to improve the corrosion resistance of the current operated material is needed so that it can be applied for higher temperature application. In this research, the effect of chromizing process on the oxidation behaviour of T91 steel was investigated under steam condition. In order to deposit chromium, mixture of chromium (Cr) powder as master alloy, halide salt (NH4Cl) powder as activator and alumina (Al2O3) powder as inert filler were inserted into alumina retort together with the steel sample and heated inside furnace at 1050°C for ten hours under argon gas environment. Furthermore, for the oxidation process, steels were exposed at 700°C at different oxidation time (6h-24h) under steam condition. From FESEM/EDX analysis, it was found that oxidation rate of pack cemented steel was lower than the un-packed steel. These results show that Cr from chromizing process was able to become reservoir for the formation of Cr2O3 in high temperature steam oxidation, and its existence can be used for a longer oxidation time.

Occult exposure to asbestos in steel workers revealed by bronchoalveolar lavage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corhay, J.-L.; Delavignette, J.-P.; Bury, T.

To investigate the asbestos burden in a steelplant environment, we counted asbestos bodies (ABs) in the bronchoalveolar lavage fluid (BALF) of 65 steel workers who had retired during the previous 5 y. They had worked for at least 15 y in the same area of the plant (coke oven or blast furnace) as maintenance or production workers. On the basis of occupational anamnesis, 28 had occasional past professional exposure to asbestos; the remaining 37 workers denied any contact with asbestos. A total of 54 white-collar workers who had no occupational exposure to asbestos were included in the study as controls.more » An increased prevalence and concentration of ABs was found in the BALF of steel workers. Electron microscopy and EDAX analysis of AB from steel workers revealed that the core fibers were mainly amphiboles. More ABs were found in the BALF of maintenance workers than in production workers. However, the BALF from steel workers who denied any contact with asbestos revealed an increased AB burden v. controls. This demonstrates that steel workers may be subject to an occult exposure to amphiboles in the steelplant environment.« less

46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The repairs...

46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The repairs...

46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The repairs...

46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The repairs...

46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The repairs...

Irradiation Microstructure of Austenitic Steels and Cast Steels Irradiated in the BOR-60 Reactor at 320°C

NASA Astrophysics Data System (ADS)

Yang, Yong; Chen, Yiren; Huang, Yina; Allen, Todd; Rao, Appajosula

Reactor internal components are subjected to neutron irradiation in light water reactors, and with the aging of nuclear power plants around the world, irradiation-induced material degradations are of concern for reactor internals. Irradiation-induced defects resulting from displacement damage are critical for understanding degradation in structural materials. In the present work, microstructural changes due to irradiation in austenitic stainless steels and cast steels were characterized using transmission electron microscopy. The specimens were irradiated in the BOR-60 reactor, a fast breeder reactor, up to 40 dpa at 320°C. The dose rate was approximately 9.4x10-7 dpa/s. Void swelling and irradiation defects were analyzed for these specimens. A high density of faulted loops dominated the irradiated-altered microstructures. Along with previous TEM results, a dose dependence of the defect structure was established at 320°C.

Respiratory status of stainless steel and mild steel welders.

PubMed

Kalliomäki, P L; Kalliomäki, K; Korhonen, O; Nordman, H; Rahkonen, E; Vaaranen, V

1982-01-01

Eighty-three full-time stainless steel and 29 mild steel welders from one shipyard were examined clinically, and their lung function was measured. The stainless steel welders had used both tungsten inert-gas (low-fume concentration) and manual metal-arc (MMA) (high-fume concentration) welding methods. The individual exposure of the welders was estimated based on the time spent doing MMA welding, the amount of retained contaminants in the lungs (magnetopulmography), and urinary chromium excretion. The results suggest that there is a greater prevalence of small airway disease among shipyard mild steel MMA welders than among stainless steel welders. Among the stainless steel welders the impairment of lung function parameters was associated with the MMA welding method. The type of welding, then, is important when the health hazards of welders are studied, and welders cannot be regarded as a single, homogeneous group.

Vision-based surface defect inspection for thick steel plates

NASA Astrophysics Data System (ADS)

Yun, Jong Pil; Kim, Dongseob; Kim, KyuHwan; Lee, Sang Jun; Park, Chang Hyun; Kim, Sang Woo

2017-05-01

There are several types of steel products, such as wire rods, cold-rolled coils, hot-rolled coils, thick plates, and electrical sheets. Surface stains on cold-rolled coils are considered defects. However, surface stains on thick plates are not considered defects. A conventional optical structure is composed of a camera and lighting module. A defect inspection system that uses a dual lighting structure to distinguish uneven defects and color changes by surface noise is proposed. In addition, an image processing algorithm that can be used to detect defects is presented in this paper. The algorithm consists of a Gabor filter that detects the switching pattern and employs the binarization method to extract the shape of the defect. The optics module and detection algorithm optimized using a simulator were installed at a real plant, and the experimental results conducted on thick steel plate images obtained from the steel production line show the effectiveness of the proposed method.

Pitting and stress corrosion cracking of stainless steel

NASA Astrophysics Data System (ADS)

Saithala, Janardhan R.

An investigation has been performed to determine the pitting resistance of stainless steels and stress corrosion cracking of super duplex stainless steels in water containing chloride ions from 25 - 170°C. The steels studied are 12% Cr, FV520B, FV566, 304L, Uranus65, 2205, Ferallium Alloy 255, and Zeron 100. All these commercial materials used in very significant industrial applications and suffer from pitting and stress corrosion failures. The design of a new experimental setup using an autoclave enabled potentiodynamic polarisation experiments and slow strain rate tests in dilute environments to be conducted at elevated temperatures. The corrosion potentials were controlled using a three electrode cell with computer controlled potentiostat.The experimental programme to determine pitting potentials was designed to simulate the service conditions experienced in most industrial plants and develop mathematical model equations to help a design engineer in material selection decision. Stress corrosion resistance of recently developed Zeron100 was evaluated in dilute environments to propose a mechanism in chloride solutions at high' temperatures useful for the nuclear and power generation industry. Results have shown the significance of the composition of alloying elements across a wide range of stainless steels and its influence on pitting. Nitrogen and molybdenum added to modern duplex stainless steels was found to be unstable at higher temperatures. The fractographic results obtained using the scanning electron microscope (SEM) has given insight in the initiation of pitting in modem duplex and super duplex stainless steels. A mathematical model has been proposed to predict pitting in stainless steels based on the effect of environmental factors (temperature, chloride concentration, and chemical composition). An attempt has been made to identify the mechanism of SCC in Zeron100 super duplex stainless steel.The proposed empirical models have shown good correlation

EMISSION FACTORS FOR IRON AND STEEL SOURCES: CRITERIA AND TOXIC POLLUTANTS

EPA Science Inventory

The report provides a comprehensive set of emission factors for sources of both criteria and toxic air pollutants in integrated iron and steel plants and specialty electric arc shops (minimills). Emission factors are identified for process sources, and process and open source fug...

Looking southwest toward the basic oxygen steelmaking plant from a ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking southwest toward the basic oxygen steelmaking plant from a neighborhodd in Braddock by Eleventh Street. - U.S. Steel Edgar Thomson Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Braddock, Allegheny County, PA

Creep Tests and Modeling Based on Continuum Damage Mechanics for T91 and T92 Steels

NASA Astrophysics Data System (ADS)

Pan, J. P.; Tu, S. H.; Zhu, X. W.; Tan, L. J.; Hu, B.; Wang, Q.

2017-12-01

9-11%Cr ferritic steels play an important role in high-temperature and high-pressure boilers of advanced power plants. In this paper, a continuum damage mechanics (CDM)-based creep model was proposed to study the creep behavior of T91 and T92 steels at high temperatures. Long-time creep tests were performed for both steels under different conditions. The creep rupture data and creep curves obtained from creep tests were captured well by theoretical calculation based on the CDM model over a long creep time. It is shown that the developed model is able to predict creep data for the two ferritic steels accurately up to tens of thousands of hours.

Creep modeling for life evaluation and strengthening mechanism of tungsten alloyed 9-12% Cr steels

NASA Astrophysics Data System (ADS)

Park, Kyu-Seop; Bae, Dong-Sik; Lee, Sung-Keun; Lee, Goo-Hyun; Kim, Jung-Ho; Endo, Takao

2006-10-01

Recently, high strength tungsten (W) alloyed steels have been developed for use in power plants with higher steam conditions for environmental reasons as well as the improvement of thermal efficiency resulting in lower fuel costs. In order to establish a creep modeling of high strength martensitic steel and to understand the basic role of W in tungsten alloyed 9-12Cr steels, conventional martensitic steels (X20CrMoV121, X20CrMoWV121, and Mod9Cr-1Mo) and tungsten alloyed steels (NF616 and HCM12A) were employed for creep tests and creep behavior analyses by the Ω method. The proposed creep model, which takes into account both primary and tertiary creep, satisfactorily described the creep curves and accurately predicted creep life, as martensitic steel undergoes a relatively large amount of primary creep, up to nearly 30%, over its normal life. The tungsten alloyed steels exhibited a smaller minimum creep rate and a larger stress exponent compared to the conventional steels. In addition, in tungsten alloyed steel, the Ω value features strong stress dependence such that creep life is prolonged at lower stresses due to high Ω values. The importance of the Ω value from the standpoint of creep strengthening in primary and tertiary creep is discussed.

Ergonomic design of crane cabins: a case study from a steel plant in India.

PubMed

Ray, Pradip Kumar; Tewari, V K

2012-01-01

The study, carried out at the Batch Annealing Furnace (BAF) shop of Cold Rolling Mill (CRM) at an integrated steel plant of India, concerns ergonomic evaluation and redesign of a manually-operated Electrical Overhead Travelling (EOT) crane cabin. The crane cabin is a complex worksystem consisting of the crane operator and twelve specific machine components embedded in a closed workspace. A crane operator has to perform various activities, such as loading and unloading of coils, setting and removal of convector plates, and routine maintenance work. Initially, an operator had to work in standing posture with bent back most of the time. Ergonomically poor design of the chair and the controls, awkward work postures, and insufficient vision angle resulting in musculoskeletal disorders (MSDs) are some of the critical problems observed.. The study, conceived as an industry-academia joint initiative, was undertaken by a design team, the members of which were drawn from both the company concerned and the institute. With the project executed successfully, a number of lessons, such as how to minimize the anthropometric mismatch, how to improve the layout of the components and controls within enclosed workspace, and how to improve work posture minimizing risk of MSDs have been learned.

Connections: Superplasticity, Damascus Steels, Laminated Steels, and Carbon Dating

NASA Astrophysics Data System (ADS)

Wadsworth, Jeffrey

2016-12-01

In this paper, a description is given of the connections that evolved from the initial development of a family of superplastic plain carbon steels that came to be known as Ultra-High Carbon Steels (UHCS). It was observed that their very high carbon contents were similar, if not identical, to those of Damascus steels. There followed a series of attempts to rediscover how the famous patterns found on Damascus steels blades were formed. At the same time, in order to improve the toughness at room temperature of the newly-developed UHCS, laminated composites were made of alternating layers of UHCS and mild steel (and subsequently other steels and other metals). This led to a study of ancient laminated composites, the motives for their manufacture, and the plausibility of some of the claims relating to the number of layers in the final blades. One apparently ancient laminated composite, recovered in 1837 from the great pyramid of Giza which was constructed in about 2750 B.C., stimulated a carbon dating study of ancient steels. The modern interest in "Bladesmithing" has connections back to many of these ancient weapons.

Have women born outside the U.K. driven the rise in U.K. births since 2001?

PubMed

Tromans, Nicola; Natamba, Eva; Jefferie, Julie

2009-01-01

The number of births in the U.K. has increased each year since 2001. This article examines the demographic drivers underlying this rise, assessing the contribution of U.K. born and foreign born women. It brings together key information from across the U.K. to provide a coherent picture of childbearing trends among U.K. born and foreign born women since 2001. Geographical variations in the proportion of births to foreign born women are also explored at the local authority level.

Transmutation and activation of reduced activation ferritic martensitic steel in molten salt cooled fusion power plants

NASA Astrophysics Data System (ADS)

Cheng, E. T.

2004-08-01

Neutron activation analysis was conducted for the reduced activation ferritic/martensitic (RAFM) steel used in flibe molten-salt cooled fusion blankets. After 22.4 MW yr/m 2 of neutron exposure, the RAFM steel first wall in a molten salt blanket with 40% lithium-6 enrichment in lithium was found to be within 1 mSv/h in contact dose rate after 100 yr of cooling. The contact dose rate drops to 30 and 20 μSv/h or less, respectively, when the cooling times are 300 and 500 yr after discharge. The RAFM steel discharged from the high-temperature shield component would be allowed for hands-on recycling after 100 yr of cooling, when the contact dose rate is 10 μSv/h or less. The most significant changes found in the RAFM steel first wall due to nuclear transmutation, are 10% decrease in W and 10% increase in Ti. Additionally, there are minor elements produced: Mn - <1.2%, V - <0.26%, Re - <0.2%, Ta - <0.08%, and Os - <0.1%, all in weight percent. The gaseous elements generated are H and He, and the, respectively, accumulated quantities are about 260 and 190 wppm.

Hardness of AISI type 410 martensitic steels after high temperature irradiation via nanoindentation

NASA Astrophysics Data System (ADS)

Waseem, Owais Ahmed; Jeong, Jong-Ryul; Park, Byong-Guk; Maeng, Cheol-Soo; Lee, Myoung-Goo; Ryu, Ho Jin

2017-11-01

The hardness of irradiated AISI type 410 martensitic steel, which is utilized in structural and magnetic components of nuclear power plants, is investigated in this study. Proton irradiation of AISI type 410 martensitic steel samples was carried out by exposing the samples to 3 MeV protons up to a 1.0 × 1017 p/cm2 fluence level at a representative nuclear reactor coolant temperature of 350 °C. The assessment of deleterious effects of irradiation on the micro-structure and mechanical behavior of the AISI type 410 martensitic steel samples via transmission electron microscopy-energy dispersive spectroscopy and cross-sectional nano-indentation showed no significant variation in the microscopic or mechanical characteristics. These results ensure the integrity of the structural and magnetic components of nuclear reactors made of AISI type 410 martensitic steel under high-temperature irradiation damage levels up to approximately 5.2 × 10-3 dpa.

Innovative UK Approaches to Acquisition Management

DTIC Science & Technology

2009-05-01

Financial and Operational Imperatives Size of UK armed forces UK Industry ? Political influence PFI / PPP Increased Scrutiny - NAO “ Commercialisation “ of the...acquisition KNOWLEDGE (EXPERIENCE – Lessons learned) KNOWLEDGE (Training) KNOWLEDGE ( Education ) OPTIMAL OPERATIONAL PERFORMANCE Operational Capability UK

The factors influencing urinary arsenic excretion and metabolism of workers in steel and iron smelting foundry.

PubMed

Shuhua, Xi; Qingshan, Sun; Fei, Wang; Shengnan, Liu; Ling, Yan; Lin, Zhang; Yingli, Song; Nan, Yan; Guifan, Sun

2014-01-01

In order to evaluate the degree of arsenic (As) exposure and the factors influencing urinary As excretion and metabolism, 192 workers from a steel and iron smelting plant, with different type of work in production such as roller, steel smelting, iron smelting and metallic charge preparation, were recruited. Information about characteristics of each subject was obtained by questionnaire and inorganic As (iAs), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA) in urine were determined. The results showed that steel smelters had significantly higher concentrations of DMA and total As (TAs) than rollers and metallic charge preparation workers, and iron and steel smelters had a higher value of primary methylation index and lower proportion of the iAs (iAs%) than rollers and metallic charge preparation workers. In steel smelters, urinary As level exceeded the biological exposure index (BEI) limit for urinary As of 35 μg/l by 65.52%, and higher than metallic charge preparation workers (35.14%). The individuals consumed seafood in recent 3 days had a higher TAs than the individuals without seafood consumption. Multivariate logistic regression analysis showed that different jobs, taken Chinese medicine of bezoar and seafood consumption in recent 3 days were significantly associated with urinary TAs exceeded BEI limit value 35 μg/l. Our results suggest that workers in steel and iron smelting plant had a lower level of As exposure, and seafood consumption and taking Chinese medicine of bezoar also could increase the risk of urinary TAs exceeded BEI limit value.

Looking south at the open hearth steelmaking plant; open hearth ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking south at the open hearth steelmaking plant; open hearth stockhouse in foreground and open hearth furnace building in background - U.S. Steel Edgar Thomson Works, Open Hearth Steelmaking Plant, Along Monongahela River, Braddock, Allegheny County, PA

32. SOUTHEASTERN VIEW OF GAS CLEANING PLANT, WITH BOP SHOP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. SOUTHEASTERN VIEW OF GAS CLEANING PLANT, WITH BOP SHOP IN BACKGROUND AND OPEN HEARTH STEELMAKING OFFICE BUILDING TO THE RIGHT. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Report on primate supply for biomedical scientific work in the UK. EUPREN UK Working Party.

PubMed

Owen, S; Thomas, C; West, P; Wolfensohn, S; Wood, M

1997-10-01

A Working Party of the UK group of European Primate Resources Network (EUPREN) considered primate supply for scientific work in the UK. Through a questionnaire, which achieved a very good response, it obtained details of primate use, sources and breeding in the UK and it put forward options to ensure that animal welfare is the best possible whilst ensuring continued supply. The questionnaire showed that contract research laboratories and pharmaceutical companies use about 80% of the 4233 primates used annually at the moment, with the rest accounted for by academic establishments and public sector laboratories. Fifty-four per cent are cynomolgus macaques (Macaca fascicularis), of which nearly 90% are captive-bred outside the European Union (EU), the remainder being bred in the UK. Nearly 90% of cynomolgus macaques are used by only five institutions. Thirty-seven per cent of primates used are marmosets (Callithrix jacchus jacchus), all of which are bred in the UK. Most of the rest are rhesus macaques (Macaca mulatta), about half of which are captive-bred outside the EU, the other half being bred in the UK. Overall primate use has increased from about 3000 per year in 1990 and users predict that requirements for all species except baboons (Papio sp.) will be maintained or increase. Marmoset breeding in the UK is already closely matched to use, and it could be increased reasonably easily if necessary. Some of the existing breeding centres of macaques in the UK would be prepared to consider expanding to supply others, although investment and imported breeding stock would be needed and it is likely that a large investment would be needed to breed a significant fraction of the macaque use in the UK. A further problem is that the users of only about 10% of the cynomolgus macaques said that they could replace this species by rhesus macaques, which are easier to breed in the UK. The questionnaire showed that much of the use of macaques would be transferred to other countries

Effect of Heat Treatment Technique on the Low Temperature Impact Toughness of Steel EQ70 for Offshore Structure

NASA Astrophysics Data System (ADS)

Tao, Su-Fen; Xia, Yun-Jin; Wang, Fu-Ming; Li, Jie; Fan, Ding-Dong

2017-09-01

Circle quenching and tempering (CQ&T), intercritical quenching and tempering (IQ&T) and regular quenching and tempering (Q&T) were used to study the influence of heat treatment techniques on the low temperature impact toughness of steel EQ70 for offshore structure. The steels with 2.10 wt. % Ni (steel A) and 1.47 wt. % Ni (steel B) were chosen to analyze the effect of Ni content on the low temperature impact toughness of steel EQ70 for offshore structure. The fracture morphologies were examined by using a scanning electron microscope (SEM, JSM-6480LV), and microstructures etched by 4 vol. % nitric acid were observed on a type 9XB-PC optical microscope. The results show that the impact toughness of steel A is higher than that of steel B at the same test temperature and heat treatment technique. For steel B, the energy absorbed is, in descending order, CQ&T, Q&T and IQ&T, while for steel A, that is CQ&T, IQ&T and Q&T. The effects of heat treatment on the low temperature impact toughness are different for steels A and B, the absorbed energy changes more obviously for steel A. The results can be significant references for actual heat treatment techniques in steel plant.

Promising Sparingly Alloyed Boron-Bearing Steels for the Production of High-Strength Fasteners

NASA Astrophysics Data System (ADS)

Bobylev, M. V.; Koroleva, E. G.; Shtannikov, P. A.

2005-05-01

The main advantages of boron-bearing steels used for production of rolled sections at cold upset shops of Russian automotive plants are considered. A thermodynamic model for the majority of boron-bearing steels for high-strength fasteners is used to plot nomograms characterizing the effect of titanium, aluminum, nitrogen, and boron on the amount of nitrides and oxides segregated in crystallization and on the content of effective boron. The effect of effective boron on the characteristics of hardenability is estimated. The studies conducted are used for determining the range of permissible contents of titanium and aluminum ensuring through hardenability of rolled bars from steels 12G1R, 20G2R, and 30G1R up to 25 mm in diameter.

Changes needed to medicine in the UK before senior UK-trained doctors, working outside the UK, will return: questionnaire surveys undertaken between 2004 and 2015.

PubMed

Lambert, Trevor W; Smith, Fay; Goldacre, Michael J

2017-12-01

To report the changes to UK medicine which doctors who have emigrated tell us would increase their likelihood of returning to a career in UK medicine. Questionnaire survey. UK-trained medical graduates. Questionnaires were sent 11 years after graduation to 7158 doctors who qualified in 1993 and 1996 in the UK: 4763 questionnaires were returned. Questionnaires were sent 17 and 19 years after graduation to the same cohorts: 4554 questionnaires were returned. Comments from doctors working abroad about changes needed to UK medicine before they would return. Eleven years after graduation, 290 (6%) of respondents were working in medicine abroad; 277 (6%) were doing so 17/19 years after graduation. Eleven years after graduation, 53% of doctors working abroad indicated that they did not intend to return, and 71% did so 17/19 years after graduation. These respondents reported a number of changes which would need to be made to UK medicine in order to increase the likelihood of them returning. The most frequently mentioned changes cited concerned 'politics/management/funding', 'pay/pension', 'posts/security/opportunities', 'working conditions/hours', and 'factors outside medicine'. Policy attention to factors including funding, pay, management and particularly the clinical-political interface, working hours, and work-life balance may pay dividends for all, both in terms of persuading some established doctors to return and, perhaps more importantly, encouraging other, younger doctors to believe that the UK and the National Health Service can offer them a satisfying and rewarding career.

Bond characteristics of steel fiber and deformed reinforcing steel bar embedded in steel fiber reinforced self-compacting concrete (SFRSCC)

NASA Astrophysics Data System (ADS)

Aslani, Farhad; Nejadi, Shami

2012-09-01

Steel fiber reinforced self-compacting concrete (SFRSCC) is a relatively new composite material which congregates the benefits of the self-compacting concrete (SCC) technology with the profits derived from the fiber addition to a brittle cementitious matrix. Steel fibers improve many of the properties of SCC elements including tensile strength, ductility, toughness, energy absorption capacity, fracture toughness and cracking. Although the available research regarding the influence of steel fibers on the properties of SFRSCC is limited, this paper investigates the bond characteristics between steel fiber and SCC firstly. Based on the available experimental results, the current analytical steel fiber pullout model (Dubey 1999) is modified by considering the different SCC properties and different fiber types (smooth, hooked) and inclination. In order to take into account the effect of fiber inclination in the pullout model, apparent shear strengths ( τ ( app)) and slip coefficient ( β) are incorporated to express the variation of pullout peak load and the augmentation of peak slip as the inclined angle increases. These variables are expressed as functions of the inclined angle ( ϕ). Furthurmore, steel-concrete composite floors, reinforced concrete floors supported by columns or walls and floors on an elastic foundations belong to the category of structural elements in which the conventional steel reinforcement can be partially replaced by the use of steel fibers. When discussing deformation capacity of structural elements or civil engineering structures manufactured using SFRSCC, one must be able to describe thoroughly both the behavior of the concrete matrix reinforced with steel fibers and the interaction between this composite matrix and discrete steel reinforcement of the conventional type. However, even though the knowledge on bond behavior is essential for evaluating the overall behavior of structural components containing reinforcement and steel fibers

Moving toward the circular economy: the role of stocks in the Chinese steel cycle.

PubMed

Pauliuk, Stefan; Wang, Tao; Müller, Daniel B

2012-01-03

As the world's largest CO(2) emitter and steel producer, China has set the ambitious goal of establishing a circular economy which aims at reconciling economic development with environmental protection and sustainable resource use. This work applies dynamic material flow analysis to forecast production, recycling, and iron ore consumption in the Chinese steel cycle until 2100 by using steel services in terms of in-use stock per capita as driver of future development. The whole cycle is modeled to determine possible responses of the steel industry in light of the circular economy concept. If per-capita stock saturates at 8-12 tons as evidence from industrialized countries suggests, consumption may peak between 2015 and 2020, whereupon it is likely to drop by up to 40% until 2050. A slower growing in-use stock could mitigate this peak and hence reduce overcapacity in primary production. Old scrap supply will increase substantially and it could replace up to 80% of iron ore as resource for steel making by 2050. This would require advanced recycling technologies as manufacturers of machinery and transportation equipment would have to shift to secondary steel as well as new capacities in secondary production which could, however, make redundant already existing integrated steel plants.

Recent Niobium Developments for High Strength Steel Energy Applications

NASA Astrophysics Data System (ADS)

Jansto, Steven G.

Niobium-containing high strength steel materials have been developed for oil and gas pipelines, offshore platforms, nuclear plants, boilers and alternative energy applications. Recent research and the commercialization of alternative energy applications such as windtower structural supports and power transmission gear components provide enhanced performance. Through the application of these Nb-bearing steels in demanding energy-related applications, the designer and end user experience improved toughness at low temperature, excellent fatigue resistance and fracture toughness and excellent weldability. These enhancements provide structural engineers the opportunity to further improve the structural design and performance. For example, through the adoption of these Nb-containing structural materials, several design-manufacturing companies are initiating new windtower designs operating at higher energy efficiency, lower cost, and improved overall material design performance.

Assessment of Land and Water Resource Implications of the UK 2050 Carbon Plan

NASA Astrophysics Data System (ADS)

Konadu, D. D.; Sobral Mourao, Z.; Skelton, S.; Lupton, R.

2015-12-01

The UK Carbon Plan presents four low-carbon energy system pathways that achieves 80% GHG emission targets by 2050, stipulated in the UK Climate Change Act (2008). However, some of the energy technologies prescribed under these pathways are land and water intensive; but would the increase demand for land and water under these pathways lead to increased competition and stress on agricultural land, and water resources in the UK? To answer the above question, this study uses an integrated modelling approach, ForeseerTM, which characterises the interdependencies and evaluates the land and water requirement for the pathways, based on scenarios of power plant location, and the energy crop yield projections. The outcome is compared with sustainable limits of resource appropriation to assess potential stresses and competition for water and land by other sectors of the economy. The results show the Carbon Plan pathways have low overall impacts on UK water resources, but agricultural land use and food production could be significantly impacted. The impact on agricultural land use is shown to be mainly driven by projections for transport decarbonisation via indigenously sourced biofuels. On the other hand, the impact on water resources is mainly associated with increased inland thermal electricity generation capacity, which would compete with other industrial and public water demands. The results highlight the need for a critical appraisal of UK's long term low-carbon energy system planning, in particular bioenergy sourcing strategy, and the siting of thermal power generation in order to avert potential resource stress and competition.

Development of Creep-Resistant and Oxidation-Resistant Austenitic Stainless Steels for High Temperature Applications

NASA Astrophysics Data System (ADS)

Maziasz, Philip J.

2018-01-01

Austenitic stainless steels are cost-effective materials for high-temperature applications if they have the oxidation and creep resistance to withstand prolonged exposure at such conditions. Since 1990, Oak Ridge National Laboratory (ORNL) has developed advanced austenitic stainless steels with creep resistance comparable to Ni-based superalloy 617 at 800-900°C based on specially designed "engineered microstructures" utilizing a microstructure/composition database derived from about 20 years of radiation effect data on steels. The wrought high temperature-ultrafine precipitate strengthened (HT-UPS) steels with outstanding creep resistance at 700-800°C were developed for supercritical boiler and superheater tubing for fossil power plants in the early 1990s, the cast CF8C-Plus steels were developed in 1999-2001 for land-based gas turbine casing and diesel engine exhaust manifold and turbocharger applications at 700-900°C, and, in 2015-2017, new Al-modified cast stainless steels with oxidation and creep resistance capabilities up to 950-1000°C were developed for automotive exhaust manifold and turbocharger applications. This article reviews and summarizes their development and their properties and applications.

Occupational health risk assessment of volatile organic compounds emitted from the coke production unit of a steel plant.

PubMed

Dehghani, Fateme; Omidi, Fariborz; Heravizadeh, Omidreza; Barati Chamgordani, Saied; Gharibi, Vahid; Sotoudeh Manesh, Akbar

2018-03-27

In this study, cancer and non-cancer risks of exposure to volatile organic compounds in the coke production unit of a steel plant were evaluated. To determine individual exposure to benzene, toluene, xylene and ethylbenzene, personal samples were taken from the breathing zone of workers according to National Institute for Occupational Safety and Health (NIOSH) method 1501. Cancer and non-cancer risk assessment was performed, using US Environmental Protection Agency (US EPA) methods. Samples analysis showed that the concentration of benzene in the energy and biochemistry and the benzol refinement sections was higher than occupational exposure limits. The cancer risk for benzene in all sections was significantly higher than allowable limit; the non-cancer risk for benzene in all sections and toluene in the benzol refinement section was also higher than 1.0. In conclusion, the current control measures are not sufficient and should be improved for efficient control of occupational exposures.

Enhancing the Biodiversity of Ditches in Intensively Managed UK Farmland

PubMed Central

Shaw, Rosalind F.; Johnson, Paul J.; Macdonald, David W.; Feber, Ruth E.

2015-01-01

Drainage ditches, either seasonally flooded or permanent, are commonly found on intensively managed lowland farmland in the UK. They are potentially important for wetland biodiversity but, despite their ubiquity, information on their biodiversity and management in the wider countryside is scarce. We surveyed 175 ditches for their physical and chemical characteristics, spatial connectivity, plant communities and aquatic invertebrates in an area of intensively managed farmland in Oxfordshire, UK and collected information on ditch management from farmer interviews. Water depth and shade had a small impact on the diversity of plant and invertebrate communities in ditches. Increased shade over the ditch channel resulted in reduced taxonomic richness of both channel vegetation and aquatic invertebrates and channel vegetation cover was lower at shaded sites. Invertebrate taxonomic richness was higher when water was deeper. Spatial connectivity had no detectable impact on the aquatic invertebrate or plant communities found in ditches. The number of families within the orders Ephemeroptera, Plecoptera and Trichoptera (EPT), which contain many pollution-sensitive species, declined with decreasing pH of ditch water. As time since dredging increased, the number of EPT families increased in permanent ditches but decreased in temporary ditches. Whether or not a ditch was in an agri-environment scheme had little impact on the reported management regime or biodiversity value of the ditch. Measures for increasing the amount of water in ditches, by increasing the water depth or promoting retention of water in ditches, could increase the biodiversity value of ditches in agricultural land. Some temporary ditches for specialised species should be retained. Reducing the amount of shade over narrow ditches by managing adjacent hedgerows is also likely to increase the species diversity of plant and invertebrate communities within the ditch. We recommend that to preserve or enhance the

Enhancing the Biodiversity of Ditches in Intensively Managed UK Farmland.

PubMed

Shaw, Rosalind F; Johnson, Paul J; Macdonald, David W; Feber, Ruth E

2015-01-01

Drainage ditches, either seasonally flooded or permanent, are commonly found on intensively managed lowland farmland in the UK. They are potentially important for wetland biodiversity but, despite their ubiquity, information on their biodiversity and management in the wider countryside is scarce. We surveyed 175 ditches for their physical and chemical characteristics, spatial connectivity, plant communities and aquatic invertebrates in an area of intensively managed farmland in Oxfordshire, UK and collected information on ditch management from farmer interviews. Water depth and shade had a small impact on the diversity of plant and invertebrate communities in ditches. Increased shade over the ditch channel resulted in reduced taxonomic richness of both channel vegetation and aquatic invertebrates and channel vegetation cover was lower at shaded sites. Invertebrate taxonomic richness was higher when water was deeper. Spatial connectivity had no detectable impact on the aquatic invertebrate or plant communities found in ditches. The number of families within the orders Ephemeroptera, Plecoptera and Trichoptera (EPT), which contain many pollution-sensitive species, declined with decreasing pH of ditch water. As time since dredging increased, the number of EPT families increased in permanent ditches but decreased in temporary ditches. Whether or not a ditch was in an agri-environment scheme had little impact on the reported management regime or biodiversity value of the ditch. Measures for increasing the amount of water in ditches, by increasing the water depth or promoting retention of water in ditches, could increase the biodiversity value of ditches in agricultural land. Some temporary ditches for specialised species should be retained. Reducing the amount of shade over narrow ditches by managing adjacent hedgerows is also likely to increase the species diversity of plant and invertebrate communities within the ditch. We recommend that to preserve or enhance the

Castings, Steel, Homogenization of Steel Castings

DTIC Science & Technology

1942-12-05

concerninr.. the ef- fe~ct of homogenizing herat-- treAment u-non the ballistic prop- erties -%f cLast steel armo--iercinr nrro jectilt:s. .arden.YD- 1 t...of hLmogenizing- treAments upon the3 corrosi;.A -.f quenched- Lr(- t c,-.rnered. c-.st steel. Harich, Riffin, -ri Bolotsk-2 .. ade two-bec-d weldahtil

Advanced Carbon Materials Center Established At UK

Science.gov Websites

UK Home Academics Athletics Medical Center Research Site Index Search UK University Master ] [research at UK] Advanced Carbon Materials Center Established At UK The tiny but mighty nanotube will continue to be the subject of several research projects at the University of Kentucky, thanks in part to a

Corrosion of stainless steels in the riser during co-processing of bio-oils in a fluid catalytic cracking pilot plant

DOE PAGES

Brady, M. P.; Keiser, J. R.; Leonard, D. N.; ...

2017-01-31

Co-processing of bio-oils with conventional petroleum-based feedstocks is an attractive initial option to make use of renewable biomass as a fuel source while leveraging existing refinery infrastructures. But, bio-oils and their processing intermediates have high concentrations of organic oxygenates, which, among their other negative qualities, can result in increased corrosion issues. A range of stainless steel alloys (409, 410, 304L, 316L, 317L, and 201) was exposed at the base of the riser in a fluid catalytic cracking pilot plant while co-processing vacuum gas oil with pine-derived pyrolysis bio-oils that had been catalytically hydrodeoxygenated to ~ 2 to 28% oxygen. Wemore » studied the processing using a catalyst temperature of 704 °C, a reaction exit temperature of 520 °C, and total co-processing run times of 57–75 h. External oxide scaling 5–30 μm thick and internal attack 1–5 μm deep were observed in these short-duration exposures. The greatest extent of internal attack was observed for co-processing with the least stabilized bio-oil, and more so for types 409, 410, 304L, 316L, 317L stainless steel than for type 201. Finally, the internal attack involved porous Cr-rich oxide formation, associated with local Ni-metal enrichment and S-rich nanoparticles, primarily containing Cr or Mn. Implications for alloy selection and corrosion are discussed.« less

Corrosion of stainless steels in the riser during co-processing of bio-oils in a fluid catalytic cracking pilot plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brady, M. P.; Keiser, J. R.; Leonard, D. N.

Co-processing of bio-oils with conventional petroleum-based feedstocks is an attractive initial option to make use of renewable biomass as a fuel source while leveraging existing refinery infrastructures. But, bio-oils and their processing intermediates have high concentrations of organic oxygenates, which, among their other negative qualities, can result in increased corrosion issues. A range of stainless steel alloys (409, 410, 304L, 316L, 317L, and 201) was exposed at the base of the riser in a fluid catalytic cracking pilot plant while co-processing vacuum gas oil with pine-derived pyrolysis bio-oils that had been catalytically hydrodeoxygenated to ~ 2 to 28% oxygen. Wemore » studied the processing using a catalyst temperature of 704 °C, a reaction exit temperature of 520 °C, and total co-processing run times of 57–75 h. External oxide scaling 5–30 μm thick and internal attack 1–5 μm deep were observed in these short-duration exposures. The greatest extent of internal attack was observed for co-processing with the least stabilized bio-oil, and more so for types 409, 410, 304L, 316L, 317L stainless steel than for type 201. Finally, the internal attack involved porous Cr-rich oxide formation, associated with local Ni-metal enrichment and S-rich nanoparticles, primarily containing Cr or Mn. Implications for alloy selection and corrosion are discussed.« less

57. Neg. No. F161D, Mar 18, 1933, INTERIORPRESSED STEEL AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

57. Neg. No. F-161D, Mar 18, 1933, INTERIOR-PRESSED STEEL AND WAREHOUSE BUILDINGS, 1ST FLOOR, SHOWING DAMAGE TO FREIGHT ELEVATOR SHAFT FROM EARTHQUAKE - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

Changes needed to medicine in the UK before senior UK-trained doctors, working outside the UK, will return: questionnaire surveys undertaken between 2004 and 2015

PubMed Central

Lambert, Trevor W; Goldacre, Michael J

2017-01-01

Objective To report the changes to UK medicine which doctors who have emigrated tell us would increase their likelihood of returning to a career in UK medicine. Design Questionnaire survey. Setting UK-trained medical graduates. Participants Questionnaires were sent 11 years after graduation to 7158 doctors who qualified in 1993 and 1996 in the UK: 4763 questionnaires were returned. Questionnaires were sent 17 and 19 years after graduation to the same cohorts: 4554 questionnaires were returned. Main outcome measures Comments from doctors working abroad about changes needed to UK medicine before they would return. Results Eleven years after graduation, 290 (6%) of respondents were working in medicine abroad; 277 (6%) were doing so 17/19 years after graduation. Eleven years after graduation, 53% of doctors working abroad indicated that they did not intend to return, and 71% did so 17/19 years after graduation. These respondents reported a number of changes which would need to be made to UK medicine in order to increase the likelihood of them returning. The most frequently mentioned changes cited concerned ‘politics/management/funding’, ‘pay/pension’, ‘posts/security/opportunities’, ‘working conditions/hours’, and ‘factors outside medicine’. Conclusions Policy attention to factors including funding, pay, management and particularly the clinical–political interface, working hours, and work–life balance may pay dividends for all, both in terms of persuading some established doctors to return and, perhaps more importantly, encouraging other, younger doctors to believe that the UK and the National Health Service can offer them a satisfying and rewarding career. PMID:29230305

Life cycle assessment of energy from waste via anaerobic digestion: a UK case study.

PubMed

Evangelisti, Sara; Lettieri, Paola; Borello, Domenico; Clift, Roland

2014-01-01

Particularly in the UK, there is potential for use of large-scale anaerobic digestion (AD) plants to treat food waste, possibly along with other organic wastes, to produce biogas. This paper presents the results of a life cycle assessment to compare the environmental impacts of AD with energy and organic fertiliser production against two alternative approaches: incineration with energy production by CHP and landfill with electricity production. In particular the paper investigates the dependency of the results on some specific assumptions and key process parameters. The input Life Cycle Inventory data are specific to the Greater London area, UK. Anaerobic digestion emerges as the best treatment option in terms of total CO2 and total SO2 saved, when energy and organic fertiliser substitute non-renewable electricity, heat and inorganic fertiliser. For photochemical ozone and nutrient enrichment potentials, AD is the second option while incineration is shown to be the most environmentally friendly solution. The robustness of the model is investigated with a sensitivity analysis. The most critical assumption concerns the quantity and quality of the energy substituted by the biogas production. Two key issues affect the development and deployment of future anaerobic digestion plants: maximising the electricity produced by the CHP unit fuelled by biogas and to defining the future energy scenario in which the plant will be embedded. Copyright © 2013 Elsevier Ltd. All rights reserved.

The steel scrap age.

PubMed

Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

2013-04-02

Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

UK Announces Intention to Join ESO

NASA Astrophysics Data System (ADS)

2000-11-01

Summary The Particle Physics and Astronomy Research Council (PPARC) , the UK's strategic science investment agency, today announced that the government of the United Kingdom is making funds available that provide a baseline for this country to join the European Southern Observatory (ESO) . The ESO Director General, Dr. Catherine Cesarsky , and the ESO Community warmly welcome this move towards fuller integration in European astronomy. "With the UK as a potential member country of ESO, our joint opportunities for front-line research and technology will grow significantly", she said. "This announcement is a clear sign of confidence in ESO's abilities, most recently demonstrated with the construction and operation of the unique Very Large Telescope (VLT) on Paranal. Together we will look forward with confidence towards new, exciting projects in ground-based astronomy." It was decided earlier this year to place the 4-m UK Visible and Infrared Survey Telescope (VISTA) at Paranal, cf. ESO Press Release 03/00. Following negotiations between ESO and PPARC, a detailed proposal for the associated UK/ESO Agreement with the various entry modalities will now be presented to the ESO Council for approval. Before this Agreement can enter into force, the ESO Convention and associated protocols must also be ratified by the UK Parliament. Research and key technologies According to the PPARC press release, increased funding for science, announced by the UK government today, will enable UK astronomers to prepare for the next generation of telescopes and expand their current telescope portfolio through membership of the European Southern Observatory (ESO). The uplift to its baseline budget will enable PPARC to enter into final negotiations for UK membership of the ESO. This will ensure that UK astronomers, together with their colleagues in the ESO member states, are actively involved in global scale preparations for the next generation of astronomy facilities. among these are ALMA

Effect of Annealing Temperature on Microstructure and Mechanical Properties of Hot-Dip Galvanizing DP600 Steel

NASA Astrophysics Data System (ADS)

Hai-yan, Sun; Zhi-li, Liu; Yang, Xu; Jian-qiang, Shi; Lian-xuan, Wang

Hot-dip galvanizing dual phase steel DP600 steel grade with low Si was produced by steel plant and experiments by simulating galvanizing thermal history. The microstructure was observed and analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The effect of different annealing temperatures on the microstructure and mechanical properties of dual-phase steel was also discussed. The experimental results show that the dual-phase steel possesses excellent strength and elongation that match EN10346 600MPa standards. The microstructure is ferrite and martensite. TEM micrograph shows that white ferrite with black martensite islands inlay with a diameter of around 1um and the content of 14 18%. The volume will expand and phase changing take the form of shear transformation when ferrite converted to martensite. So there are high density dislocations in ferrite crystalline grain near martensite. The martensite content growing will be obvious along with annealing temperature going up. But the tendency will be weak when temperature high.

Thermomechanical processing of microalloyed powder forged steels and a cast vanadium steel

NASA Astrophysics Data System (ADS)

Dogan, B.; Davies, T. J.

1985-09-01

The effects of controlled rolling on transformation behavior of two powder forged (P/F) microalloyed vanadium steels and a cast microalloyed vanadium steel were investigated. Rolling was carried out in the austenitic range below the recrystallization temperature. Equiaxed grain structures were produced in specimens subjected to different reductions and different cooling rates. The ferrite grain size decreased with increasing deformation and cooling rate. Ferrite nucleated on second phase particles, deformation bands, and on elongated prior austenite grain boundaries; consequently a high fractional ferrite refinement was achieved. Deformation raised the ferrite transformation start temperature while the time to transformation from the roll finish temperature decreased. Cooling rates in the cast steel were higher than in P/F steels for all four cooling media used, and the transformation start temperatures of cast steels were lower than that of P/F steel. Intragranular ferrite nucleation, which played a vital role in grain refinement, increased with cooling rate. Fully bainitic microstructures were formed at higher cooling rates in the cast steel. In the P/F steels inclusions and incompletely closed pores served as sites for ferrite nucleation, often forming a ‘secondary’ ferrite. The rolling schedule reduced the size of large pores and particle surface inclusions and removed interconnected porosity in the P/F steels.

Superstrength of nanograined steel with nanoscale intermetallic precipitates transformed from shock-compressed martensitic steel

PubMed Central

Yu, Hailiang; Yan, Ming; Lu, Cheng; Tieu, Anh Kiet; Li, Huijun; Zhu, Qiang; Godbole, Ajit; Li, Jintao; Su, Lihong; Kong, Charlie

2016-01-01

An increasing number of industrial applications need superstrength steels. It is known that refined grains and nanoscale precipitates can increase strength. The hardest martensitic steel reported to date is C0.8 steel, whose nanohardness can reach 11.9 GPa through incremental interstitial solid solution strengthening. Here we report a nanograined (NG) steel dispersed with nanoscale precipitates which has an extraordinarily high hardness of 19.1 GPa. The NG steel (shock-compressed Armox 500T steel) was obtained under these conditions: high strain rate of 1.2 μs−1, high temperature rise rate of 600 Kμs−1 and high pressure of 17 GPa. The mean grain size achieved was 39 nm and reinforcing precipitates were indexed in the NG steel. The strength of the NG steel is expected to be ~3950 MPa. The discovery of the NG steel offers a general pathway for designing new advanced steel materials with exceptional hardness and excellent strength. PMID:27892460

7. TYPICAL INTERIOR AND BOTTOM OF EMPTY 14.5FOOTDIAMETER RIVETED STEEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. TYPICAL INTERIOR AND BOTTOM OF EMPTY 14.5-FOOT-DIAMETER RIVETED STEEL SOAP KETTLE, WITH STEAM COILS; VIEW DOWN FROM KETTLE TOP, FIFTH FLOOR, EAST BAY, THIRD KETTLE FROM SOUTH - Colgate & Company Jersey City Plant, Building No. B-13, 48-50 Grand Street, Jersey City, Hudson County, NJ

Corrosion behavior of a superduplex stainless steel in chloride aqueous solution

NASA Astrophysics Data System (ADS)

Dabalà, Manuele; Calliari, Irene; Variola, Alessandra

2004-04-01

Super duplex stainless steels (SDSS) have been widely used as structural materials for chemical plants (especially in those engaged in phosphoric acid production), in the hydrometallurgy industries, and as materials for offshore applications due to their excellent corrosion resistance in chloride environments, compared with other commercial types of ferritic stainless steels. These alloys also possess superior weldability and better mechanical properties than austenitic stainless steels. However, due to their two-phase structure, the nature of which is very dependent on their composition and thermal history, the behavior of SDSS regarding localized corrosion appears difficult to predict, especially in chloride environments. To improve their final properties, the effect of the partition of the alloying elements between the two phases, and the composition and microstructure of each phase are the key to understanding the localized corrosion phenomena of SDSS. This paper concerns the effects of the SDSS microstructure and heat treatment on the SDSS corrosion resistance in aqueous solutions, containing different amounts of NaCl at room temperature.

The UK population: how does it compare?

PubMed

Matheson, Jil

2010-01-01

This is the fourth demographic report for the UK, providing an overview of the latest statistics on the population. This year's article compares the UK with other European countries and a range of nations from around the world. Statistical comparisons are made for fertility, mortality, ageing, migration and population density. The UK has an ageing population, but one that is not ageing as rapidly as some other countries such as Germany, Italy and Japan. Although life expectation in the UK is improving in line with most western European countries, relatively high levels of fertility ensure that the proportion of the population that is young remains high. Around one in ten residents of the UK are foreign born, a lower proportion than many developed countries. UK population density has increased steadily and is the fourth highest in the EU.

Creep Rupture of the Simulated HAZ of T92 Steel Compared to that of a T91 Steel.

PubMed

Peng, Yu-Quan; Chen, Tai-Cheng; Chung, Tien-Jung; Jeng, Sheng-Long; Huang, Rong-Tan; Tsay, Leu-Wen

2017-02-08

The increased thermal efficiency of fossil power plants calls for the development of advanced creep-resistant alloy steels like T92. In this study, microstructures found in the heat-affected zone (HAZ) of a T92 steel weld were simulated to evaluate their creep-rupture-life at elevated temperatures. An infrared heating system was used to heat the samples to 860 °C (around A C1 ), 900 °C (slightly below A C3 ), and 940 °C (moderately above A C3 ) for one minute, before cooling to room temperature. The simulated specimens were then subjected to a conventional post-weld heat treatment (PWHT) at 750 °C for two hours, where both the 900 °C and 940 °C simulated specimens had fine grain sizes. In the as-treated condition, the 900 °C simulated specimen consisted of fine lath martensite, ferrite subgrains, and undissolved carbides, while residual carbides and fresh martensite were found in the 940 °C simulated specimen. The results of short-term creep tests indicated that the creep resistance of the 900 °C and 940 °C simulated specimens was poorer than that of the 860 °C simulated specimens and the base metal. Moreover, simulated T92 steel samples had higher creep strength than the T91 counterpart specimens.

Creep Rupture of the Simulated HAZ of T92 Steel Compared to that of a T91 Steel

PubMed Central

Peng, Yu-Quan; Chen, Tai-Cheng; Chung, Tien-Jung; Jeng, Sheng-Long; Huang, Rong-Tan; Tsay, Leu-Wen

2017-01-01

The increased thermal efficiency of fossil power plants calls for the development of advanced creep-resistant alloy steels like T92. In this study, microstructures found in the heat-affected zone (HAZ) of a T92 steel weld were simulated to evaluate their creep-rupture-life at elevated temperatures. An infrared heating system was used to heat the samples to 860 °C (around AC1), 900 °C (slightly below AC3), and 940 °C (moderately above AC3) for one minute, before cooling to room temperature. The simulated specimens were then subjected to a conventional post-weld heat treatment (PWHT) at 750 °C for two hours, where both the 900 °C and 940 °C simulated specimens had fine grain sizes. In the as-treated condition, the 900 °C simulated specimen consisted of fine lath martensite, ferrite subgrains, and undissolved carbides, while residual carbides and fresh martensite were found in the 940 °C simulated specimen. The results of short-term creep tests indicated that the creep resistance of the 900 °C and 940 °C simulated specimens was poorer than that of the 860 °C simulated specimens and the base metal. Moreover, simulated T92 steel samples had higher creep strength than the T91 counterpart specimens. PMID:28772500

40 CFR 63.7782 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2014 CFR

2014-07-01

... oxygen process furnace (BOPF) shop at your integrated iron and steel manufacturing facility. (c) This... blast furnace casthouse; and the BOPF shop including each individual BOPF and shop ancillary operations... plant, blast furnace, or BOPF shop at your integrated iron and steel manufacturing facility is existing...

40 CFR 63.7782 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2013 CFR

2013-07-01

... oxygen process furnace (BOPF) shop at your integrated iron and steel manufacturing facility. (c) This... blast furnace casthouse; and the BOPF shop including each individual BOPF and shop ancillary operations... plant, blast furnace, or BOPF shop at your integrated iron and steel manufacturing facility is existing...

40 CFR 63.7782 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2012 CFR

2012-07-01

... oxygen process furnace (BOPF) shop at your integrated iron and steel manufacturing facility. (c) This... blast furnace casthouse; and the BOPF shop including each individual BOPF and shop ancillary operations... plant, blast furnace, or BOPF shop at your integrated iron and steel manufacturing facility is existing...

40 CFR 63.7782 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2011 CFR

2011-07-01

... oxygen process furnace (BOPF) shop at your integrated iron and steel manufacturing facility. (c) This... blast furnace casthouse; and the BOPF shop including each individual BOPF and shop ancillary operations... plant, blast furnace, or BOPF shop at your integrated iron and steel manufacturing facility is existing...

40 CFR 63.7782 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2010 CFR

2010-07-01

... oxygen process furnace (BOPF) shop at your integrated iron and steel manufacturing facility. (c) This... blast furnace casthouse; and the BOPF shop including each individual BOPF and shop ancillary operations... plant, blast furnace, or BOPF shop at your integrated iron and steel manufacturing facility is existing...

Articles comprising ferritic stainless steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rakowski, James M.

An article of manufacture comprises a ferritic stainless steel that includes a near-surface region depleted of silicon relative to a remainder of the ferritic stainless steel. The article has a reduced tendency to form an electrically resistive silica layer including silicon derived from the steel when the article is subjected to high temperature oxidizing conditions. The ferritic stainless steel is selected from the group comprising AISI Type 430 stainless steel, AISI Type 439 stainless steel, AISI Type 441 stainless steel, AISI Type 444 stainless steel, and E-BRITE.RTM. alloy, also known as UNS 44627 stainless steel. In certain embodiments, the articlemore » of manufacture is a fuel cell interconnect for a solid oxide fuel cell.« less

Preparation and characterization of 304 stainless steel/Q235 carbon steel composite material

NASA Astrophysics Data System (ADS)

Shen, Wenning; Feng, Lajun; Feng, Hui; Cao, Ying; Liu, Lei; Cao, Mo; Ge, Yanfeng

The composite material of 304 stainless steel reinforced Q235 carbon steel has been prepared by modified hot-rolling process. The resulted material was characterized by scanning electron microscope, three-electrode method, fault current impact method, electrochemical potentiodynamic polarization curve measurement and electrochemical impedance spectroscopy. The results showed that metallurgical bond between the stainless steel layer and carbon steel substrate has been formed. The composite material exhibited good electrical conductivity and thermal stability. The average grounding resistance of the composite material was about 13/20 of dip galvanized steel. There has no surface crack and bubbling formed after fault current impact. The composite material led to a significant decrease in the corrosion current density in soil solution, compared with that of hot dip galvanized steel and bare carbon steel. On the basis polarization curve and EIS analyses, it can be concluded that the composite material showed improved anti-corrosion property than hot-dip galvanized steel.

Methods of forming steel

DOEpatents

Branagan, Daniel J.; Burch, Joseph V.

2001-01-01

In one aspect, the invention encompasses a method of forming a steel. A metallic glass is formed and at least a portion of the glass is converted to a crystalline steel material having a nanocrystalline scale grain size. In another aspect, the invention encompasses another method of forming a steel. A molten alloy is formed and cooled the alloy at a rate which forms a metallic glass. The metallic glass is devitrified to convert the glass to a crystalline steel material having a nanocrystalline scale grain size. In yet another aspect, the invention encompasses another method of forming a steel. A first metallic glass steel substrate is provided, and a molten alloy is formed over the first metallic glass steel substrate to heat and devitrify at least some of the underlying metallic glass of the substrate.

Experimental Verification of Steel Pipe Collapse under Vacuum Pressure Conditions

NASA Astrophysics Data System (ADS)

Autrique, R.; Rodal, E.

2016-11-01

Steel pipes are used widely in hydroelectric systems and in pumping systems. Both systems are subject to hydraulic transient effects caused by changes in boundary conditions, such as sudden valve closures, pump failures, or accidents. Water column separation, and its associated vaporization pressure inside the pipe, can cause the collapse of thin walled steel pipes subject to atmospheric pressure, as happened during the well known Oigawa Power Plant accident in Japan, in 1950. The conditions under which thin walled pipes subject to external pressure can collapse have been studied mathematically since the second half of the XIX century, with classical authors Southwell and Von Mises obtaining definitive equations for long and short pipes in the second decade of the XX century, in which the fundamental variables are the diameter to thickness ratio D/t and the length to diameter ratio L/D. In this paper, the predicted critical D/t ratio for steel pipe collapse is verified experimentally, in a physical model able to reproduce hydraulic transients, generating vacuum pressures through rapid upstream valve closures.

Steel Containment Vessel Model Test: Results and Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Costello, J.F.; Hashimote, T.; Hessheimer, M.F.

A high pressure test of the steel containment vessel (SCV) model was conducted on December 11-12, 1996 at Sandia National Laboratories, Albuquerque, NM, USA. The test model is a mixed-scaled model (1:10 in geometry and 1:4 in shell thickness) of an improved Mark II boiling water reactor (BWR) containment. A concentric steel contact structure (CS), installed over the SCV model and separated at a nominally uniform distance from it, provided a simplified representation of a reactor shield building in the actual plant. The SCV model and contact structure were instrumented with strain gages and displacement transducers to record the deformationmore » behavior of the SCV model during the high pressure test. This paper summarizes the conduct and the results of the high pressure test and discusses the posttest metallurgical evaluation results on specimens removed from the SCV model.« less

An Experimental Investigation on Hardness and Microstructure of Heat Treated EN 9 Steel

NASA Astrophysics Data System (ADS)

Biswas, Palash; Kundu, Arnab; Mondal, Dhiraj

2017-08-01

In the modern engineering world, extensive research has led to the development of some special grades of steel, often suited for enhanced functions. EN 9 steel is one such grade, having major applications in power plants, automobile and aerospace industry. Different heat treatment processes are employed to achieve high hardness and high wear resistance, but machinability subsequently decreases. Existing literature is not sufficient to achieve a balance between hardness and machinability. The aim of this experimental work is to determine the hardness values and observe microstructural changes in EN9 steel, when it is subjected to annealing, normalizing and quenching. Finally, the effects of tempering after each of these heat treatments on hardness and microstructure have also been shown. It is seen that the tempering after normalizing the specimen achieved satisfactory results. The microstructure was also observed to be consisting of fine grains.

Application of Various NDT Methods for the Evaluation of Building Steel Structures for Reuse

PubMed Central

Fujita, Masanori; Masuda, Tomoya

2014-01-01

The reuse system proposed by the authors is an overall business system for realizing a cyclic reuse flow through the processes of design, fabrication, construction, maintenance, demolition and storage. The reuse system is one of the methods to reduce the environmental burden in the field of building steel structures. These buildings are assumed to be demolished within approximately 30 years or more for physical, architectural, economic and social reasons in Japan. In this paper, focusing on building steel structures used for plants, warehouses and offices without fire protection, the performance of steel structural members for reuse is evaluated by a non-destructive test. First, performance evaluation procedures for a non-destructive test, such as mechanical properties, chemical compositions, dimension and degradation, are shown. Tensile strengths are estimated using Vickers hardness measured by a portable ultrasonic hardness tester, and chemical compositions are measured by a portable optical emission spectrometer. The weldability of steel structural members is estimated by carbon equivalent and weld crack sensitivity composition using chemical compositions. Finally, the material grade of structural members of the building steel structure for reuse is estimated based on the proposed procedures. PMID:28788237

Application of Various NDT Methods for the Evaluation of Building Steel Structures for Reuse.

PubMed

Fujita, Masanori; Masuda, Tomoya

2014-10-22

The reuse system proposed by the authors is an overall business system for realizing a cyclic reuse flow through the processes of design, fabrication, construction, maintenance, demolition and storage. The reuse system is one of the methods to reduce the environmental burden in the field of building steel structures. These buildings are assumed to be demolished within approximately 30 years or more for physical, architectural, economic and social reasons in Japan. In this paper, focusing on building steel structures used for plants, warehouses and offices without fire protection, the performance of steel structural members for reuse is evaluated by a non-destructive test. First, performance evaluation procedures for a non-destructive test, such as mechanical properties, chemical compositions, dimension and degradation, are shown. Tensile strengths are estimated using Vickers hardness measured by a portable ultrasonic hardness tester, and chemical compositions are measured by a portable optical emission spectrometer. The weldability of steel structural members is estimated by carbon equivalent and weld crack sensitivity composition using chemical compositions. Finally, the material grade of structural members of the building steel structure for reuse is estimated based on the proposed procedures.

Air ion exposure system for plants

NASA Technical Reports Server (NTRS)

Morrow, R. C.; Tibbitts, T. W.

1987-01-01

A system was developed for subjecting plants to elevated air ion levels. This system consisted of a rectangular Plexiglas chamber lined with a Faraday cage. Air ions were generated by corona discharge from frayed stainless steel fibers placed at one end of the chamber. This source was capable of producing varying levels of either positive or negative air ions. During plant exposures, environmental conditions were controlled by operating the unit in a growth chamber.

Air ion exposure system for plants.

PubMed

Morrow, R C; Tibbitts, T W

1987-02-01

A system was developed for subjecting plants to elevated air ion levels. This system consisted of a rectangular Plexiglas chamber lined with a Faraday cage. Air ions were generated by corona discharge from frayed stainless steel fibers placed at one end of the chamber. This source was capable of producing varying levels of either positive or negative air ions. During plant exposures, environmental conditions were controlled by operating the unit in a growth chamber.

Precipitate design for creep strengthening of 9% Cr tempered martensitic steel for ultra-supercritical power plants

PubMed Central

Abe, Fujio

2008-01-01

It is crucial for the carbon concentration of 9% Cr steel to be reduced to a very low level, so as to promote the formation of MX nitrides rich in vanadium as very fine and thermally stable particles to enable prolonged periods of exposure at elevated temperatures and also to eliminate Cr-rich carbides M23C6. Sub-boundary hardening, which is inversely proportional to the width of laths and blocks, is shown to be the most important strengthening mechanism for creep and is enhanced by the fine dispersion of precipitates along boundaries. The suppression of particle coarsening during creep and the maintenance of a homogeneous distribution of M23C6 carbides near prior austenite grain boundaries, which precipitate during tempering and are less fine, are effective for preventing the long-term degradation of creep strength and for improving long-term creep strength. This can be achieved by the addition of boron. The steels considered in this paper exhibit higher creep strength at 650 °C than existing high-strength steels used for thick section boiler components. PMID:27877920

ELWIRA "Plants, wood, steel, concrete - a lifecycle as construction materials": University meets school - science meets high school education

NASA Astrophysics Data System (ADS)

Strauss-Sieberth, Alexandra; Strauss, Alfred; Kalny, Gerda; Rauch, Hans Peter; Loiskandl, Willibald

2016-04-01

The research project "Plants, wood, steel, concrete - a lifecycle as construction materials" (ELWIRA) is in the framework of the Sparkling Science programme performed by the University of Natural Resources and Life Sciences together with the Billroth Gymnasium in Vienna. The targets of a Sparkling Science project are twofold (a) research and scientific activities should already be transferred in the education methods of schools in order to fascinate high school students for scientific methods and to spark young people's interest in research, and (b) exciting research questions not solved and innovative findings should be addressed. The high school students work together with the scientists on their existing research questions improve the school's profile and the high school student knowledge in the investigated Sparkling Science topic and can lead to a more diverse viewing by the involvement of the high school students. In the project ELWIRA scientists collaborate with the school to quantify and evaluate the properties of classical building materials like concrete and natural materials like plants and woodlogs in terms of their life cycle through the use of different laboratory and field methods. The collaboration with the high school students is structured in workshops, laboratory work and fieldworks. For an efficient coordination/communication, learning and research progress new advanced electronic media like "Moodle classes/courses" have been used and utilized by the high school students with great interest. The Moodle classes are of high importance in the knowledge transfer in the dialogue with the high school students. The research project is structured into four main areas associated with the efficiencies of building materials: (a) the aesthetic feeling of people in terms of the appearance of materials and associated structures will be evaluated by means of jointly developed and collected questionnaires. The analysis, interpretation and evaluation are carried

Steel Industry Analysis Brief

EIA Publications

2009-01-01

The steel industry is critical to the U.S. economy. Steel is the material of choice for many elements of construction, transportation, manufacturing, and a variety of consumer products. It is the backbone of bridges, skyscrapers, railroads, automobiles, and appliances. Most grades of steel used today - particularly high-strength steels that are lighter and more versatile - were not available a decade ago.

Supertough Stainless Bearing Steel

NASA Technical Reports Server (NTRS)

Olson, Gregory B.

1995-01-01

Composition and processing of supertough stainless bearing steel designed with help of computer-aided thermodynamic modeling. Fracture toughness and hardness of steel exceeds those of other bearing steels like 440C stainless bearing steel. Developed for service in fuel and oxidizer turbopumps on Space Shuttle main engine. Because of strength and toughness, also proves useful in other applications like gears and surgical knives.

Growth and Cd uptake by rice (Oryza sativa) in acidic and Cd-contaminated paddy soils amended with steel slag.

PubMed

He, Huaidong; Tam, Nora F Y; Yao, Aijun; Qiu, Rongliang; Li, Wai Chin; Ye, Zhihong

2017-12-01

Contamination of rice (Oryza sativa) by Cd is of great concern. Steel slag could be used to amend Cd-contaminated soils and make them safe for cereal production. This work was conducted to study the effects of steel slag on Cd uptake and growth of rice plants in acidic and Cd-contaminated paddy soils and to determine the possible mechanisms behind these effects. Pot (rhizobag) experiments were conducted using rice plants grown on two acidic and Cd-contaminated paddy soils with or without steel slag amendment. Steel slag amendment significantly increased grain yield by 36-45% and root catalase activity, and decreased Cd concentrations in brown rice by 66-77% compared with the control, in both soils. Steel slag amendment also markedly decreased extractable soil Cd, Cd concentrations in pore-water and Cd translocation from roots to above-ground parts. It also significantly increased soil pH, extractable Si and Ca in soils and Ca concentrations in roots. Significant positive correlations were found between extractable soil Cd and Cd concentrations in rice tissues, but it was negatively correlated with soil pH and extractable Si. Calcium in root tissues significantly and negatively correlated with Cd translocation factors from roots to straw. Overall, steel slag amendment not only significantly promoted rice growth but decreased Cd accumulation in brown rice. These benefits appear to be related to improvements in soil conditions (e.g. increasing pH, extractable Si and Ca), a reduction in extractable soil Cd, and suppression of Cd translocation from roots to above-ground parts. Copyright © 2017 Elsevier Ltd. All rights reserved.

The influence of cooling parameters on the speed of continuous steel casting

NASA Astrophysics Data System (ADS)

Tirian, G. O.; Gheorghiu, C. A.; Hepuţ, T.; Chioncel, C. P.

2018-01-01

This paper analyzes the cooling parameters of the continuous casting speed. In the researches carried out we aimed to establish some correlation equations between the parameters characterizing the continuous casting process, the temperature of the steel at the entrance to the crystallizer, the superheating of the steel and the flow of the cooling water in the crystallizer and different zones of the secondary cooling. Parallel to these parameters were also the values for the casting speed. The research was made for the casting of round ϕ270mm semi-finished steel products. The steel was developed in an electric EBT furnace with a capacity of 100t, treated in L.F. (Ladle - Furnace) and VD (Vacuum-Degassing) and poured in a 5-wire continuous casting plant. The obtained data was processed in MATLAB using three types of correlation equations. The obtained results are presented both in the analytical and graphical form, each correlation being analyzed from the technological point of view, indicating the optimal values for the independent parameters monitored. In the analysis we present a comparison between the results obtained after the three types of equations for each correlation.

The impact of radioactive steel recycling on the public and professionals.

PubMed

Hrncir, Tomas; Panik, Michal; Ondra, Frantisek; Necas, Vladimir

2013-06-15

The decommissioning of nuclear power plants represents a complex process resulting in the generation of large amounts of waste materials, e.g. steel scrap containing various concentrations of radionuclides. Recycling some of these materials is highly desirable due to numerous reasons. Herein presented scenarios of recycling of radioactive steel within the nuclear as well as civil engineering industry are analyzed from the radiation protection point of view. An approach based on the dose constraints principle is chosen. The aim of the study is to derive conditional clearance levels (maximal specific mass activity of material allowing its recycling/clearance) for analyzed radionuclides ensuring that the detrimental impact on human health is kept on a negligible level. Determined conditional clearance levels, as the result of performed software calculations, are valid for the reuse of radioactive steel in four selected scenarios. Calculation results indicate that the increase of the amount of recyclable radioactive steel due to its reuse in specific applications may be feasible considering the radiation impact on the public and professionals. However, issues connected with public acceptance, technical difficulties and financing of potential realization are still open and they have to be examined in more detail. Copyright © 2013 Elsevier B.V. All rights reserved.

Supporting UK adaptation: building services for the next set of UK climate projections

NASA Astrophysics Data System (ADS)

Fung, Fai; Lowe, Jason

2016-04-01

As part of the Climate Change Act 2008, the UK Government sets out a national adaptation programme to address the risks and opportunities identified in a national climate change risk assessment (CCRA) every five years. The last risk assessment in 2012 was based on the probabilistic projections for the UK published in 2009 (UKCP09). The second risk assessment will also use information from UKCP09 alongside other evidence on climate projections. However, developments in the science of climate projeciton, and evolving user needs (based partly on what has been learnt about the diverse user requirements of the UK adaptation community from the seven years of delivering and managing UKCP09 products, market research and the peer-reviewed literature) suggest now is an appropriate time to update the projections and how they are delivered. A new set of UK climate projections are now being produced to upgrade UKCP09 to reflect the latest developments in climate science, the first phase of which will be delivered in 2018 to support the third CCRA. A major component of the work is the building of a tailored service to support users of the new projections during their development and to involve users in key decisions so that the projections are of most use. We will set out the plan for the new climate projections that seek to address the evolving user need. We will also present a framework which aims to (i) facilitate the dialogue between users, boundary organisations and producers, reflecting their different decision-making roles (ii) produce scientifically robust, user-relevant climate information (iii) provide the building blocks for developing further climate services to support adaptation activities in the UK.

Thermoelectric System Absorbing Waste Heat from a Steel Ladle

NASA Astrophysics Data System (ADS)

Lu, Baiyi; Meng, Xiangning; Zhu, Miaoyong; Suzuki, Ryosuke O.

2018-06-01

China's iron and steel industry has made great progress in energy savings and emission reductions with the application of many waste heat recovery technologies. However, most of the medium and low temperature waste heat and radiant waste heat has not been effectively utilized. This paper proposes a thermoelectric system that generates electricity by absorbing the radiant heat from the surface of steel ladles in a steel plant. The thermoelectric behavior of modules in this system is analyzed by a numerical simulation method. The effects of external resistance and module structure on thermoelectric performance are also discussed in the temperature range of the wall surface of a steel ladle. The results show that the wall temperature has a significant influence on the thermoelectric behavior of the module, so its uniformity and stability should be considered in practical application. The ratio of the optimum external resistance to the internal resistance of the thermoelectric module is in the range of 1.6-2.0, which indicates the importance of external load optimization for a given thermoelectric system. In addition, the output power and the conversion efficiency of the module can be significantly improved by increasing the length of the thermoelectric legs and adopting a double-layer structure. Finally, through the optimization of external resistance and structure, the power output can reach 83-304 W/m2. This system is shown to be a promising approach for energy recovery.

Thermoelectric System Absorbing Waste Heat from a Steel Ladle

NASA Astrophysics Data System (ADS)

Lu, Baiyi; Meng, Xiangning; Zhu, Miaoyong; Suzuki, Ryosuke O.

2018-01-01

China's iron and steel industry has made great progress in energy savings and emission reductions with the application of many waste heat recovery technologies. However, most of the medium and low temperature waste heat and radiant waste heat has not been effectively utilized. This paper proposes a thermoelectric system that generates electricity by absorbing the radiant heat from the surface of steel ladles in a steel plant. The thermoelectric behavior of modules in this system is analyzed by a numerical simulation method. The effects of external resistance and module structure on thermoelectric performance are also discussed in the temperature range of the wall surface of a steel ladle. The results show that the wall temperature has a significant influence on the thermoelectric behavior of the module, so its uniformity and stability should be considered in practical application. The ratio of the optimum external resistance to the internal resistance of the thermoelectric module is in the range of 1.6-2.0, which indicates the importance of external load optimization for a given thermoelectric system. In addition, the output power and the conversion efficiency of the module can be significantly improved by increasing the length of the thermoelectric legs and adopting a double-layer structure. Finally, through the optimization of external resistance and structure, the power output can reach 83-304 W/m2. This system is shown to be a promising approach for energy recovery.

A porous stainless steel membrane system for extraterrestrial crop production

NASA Technical Reports Server (NTRS)

Koontz, H. V.; Prince, R. P.; Berry, W. L.; Knott, W. M. (Principal Investigator)

1990-01-01

A system was developed in which nutrient flow to plant roots is controlled by a thin (0.98 or 1.18 mm) porous (0.2 or 0.5 microns) stainless steel sheet membrane. The flow of nutrient solution through the membrane is controlled by adjusting the relative negative pressure on the nutrient solution side of the membrane. Thus, the nutrient solution is contained by the membrane and cannot escape from the compartment even under microgravity conditions if the appropriate pressure gradient across the membrane is maintained. Plant roots grow directly on the top surface of the membrane and pull the nutrient solution through this membrane interface. The volume of nutrient solution required by this system for plant growth is relatively small, since the plenum, which contains the nutrient solution in contact with the membrane, needs only to be of sufficient size to provide for uniform flow to all parts of the membrane. Solution not passing through the membrane to the root zone is recirculated through a reservoir where pH and nutrient levels are controlled. The size of the solution reservoir depends on the sophistication of the replenishment system. The roots on the surface of the membrane are covered with a polyethylene film (white on top, black on bottom) to maintain a high relative humidity and also limit light to prevent algal growth. Seeds are sown directly on the stainless steel membrane under the holes in the polyethylene film that allow a pathway for the shoots.

Technologies for decreasing the tap temperature to save energy in steel foundries

NASA Astrophysics Data System (ADS)

Biswas, Siddhartha

Steel foundries are one of the most energy intensive industries. The increasing concerns over volatile energy cost and carbon dioxide emission have pushed foundries to improve efficiency and hence decrease electrical energy consumption. Statistical analysis of industrial survey data was combined with computational fluid dynamics (CFD) modeling to investigate the best industrial practices and opportunities to improve energy efficiency. Reducing tap temperature was identified as one of the important ways of reducing energy consumption. Steel foundries typically tap at 1650-1800°C (3000-3300°F) which is 100-250°C (150-450°F) higher than the pouring temperature. The steel temperature is elevated to compensate for the temperature loss associated with tapping, holding and transporting the liquid steel from the furnace to the pouring floor. Based on experimental investigations and CFD modeling of heat losses during holding in the ladle for different foundry practices, a spreadsheet calculator has been developed to calculate the optimum tap temperature for the specific foundry practices which will eliminate unnecessary superheating. The calculated results were compared and validated with industrial measurements. Improving the lining refractory is one significant way of reducing heat losses during holding of the steel in ladle. Silica sand linings are being used in steel foundries as an inexpensive and convenient material for short holding times and small volumes. The possibilities of improvements of silica sand linings by the addition of lower density cenospheres (hollow spheres), a byproduct of coal fired power plants, was studied through property measurements and laboratory trials.

View northwest, wharf A, sheet steel bulkhead, steel lift tower ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View northwest, wharf A, sheet steel bulkhead, steel lift tower - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

The medline UK filter: development and validation of a geographic search filter to retrieve research about the UK from OVID medline.

PubMed

Ayiku, Lynda; Levay, Paul; Hudson, Tom; Craven, Jenny; Barrett, Elizabeth; Finnegan, Amy; Adams, Rachel

2017-07-13

A validated geographic search filter for the retrieval of research about the United Kingdom (UK) from bibliographic databases had not previously been published. To develop and validate a geographic search filter to retrieve research about the UK from OVID medline with high recall and precision. Three gold standard sets of references were generated using the relative recall method. The sets contained references to studies about the UK which had informed National Institute for Health and Care Excellence (NICE) guidance. The first and second sets were used to develop and refine the medline UK filter. The third set was used to validate the filter. Recall, precision and number-needed-to-read (NNR) were calculated using a case study. The validated medline UK filter demonstrated 87.6% relative recall against the third gold standard set. In the case study, the medline UK filter demonstrated 100% recall, 11.4% precision and a NNR of nine. A validated geographic search filter to retrieve research about the UK with high recall and precision has been developed. The medline UK filter can be applied to systematic literature searches in OVID medline for topics with a UK focus. © 2017 Crown copyright. Health Information and Libraries Journal © 2017 Health Libraries GroupThis article is published with the permission of the Controller of HMSO and the Queen's Printer for Scotland.

Identification and determination of the contribution of iron-steel manufacturing industry to sediment-associated polycyclic aromatic hydrocarbons (PAHs) in a large shallow lake of eastern China.

PubMed

Zhang, Liu; Bai, Ya-Shu; Wang, Ji-Zhong; Peng, Shu-Chuan; Chen, Tian-Hu; Yin, Da-Qiang

2016-11-01

Seventeen polycyclic aromatic hydrocarbon (PAH) compounds were determined in surface sediments collected from the Chaohu Lake (a large shallow lake in eastern China) and its tributaries. Both diagnostic ratios and a receptor model (positive matrix factorization, PMF) were applied to identify and determine the contribution of a local iron-steel manufacturing plant located in the Nanfei River (NFR) to the Chaohu Lake basin. The results show that sites located in the downstream of the steel plant contained concentrations of 17 PAH (Σ 17 PAH) approximately two orders of magnitudes higher than those from other sites. Five factors were identified by the PMF model, including industrial waste, wood/biomass burning, diagenetic origin, domestic coal combustion, and industrial combustion. Our findings suggest that sediments in the downstream of the plant and in the western part of the Chaohu Lake were predominantly affected by industrial coal combustion. A mixture of pyrolytic origins impacted urban sediments in the upstream of the plant, whereas diagenetic origins along with coal and biomass burning were suggested to influence the eastern part and rural tributaries of the lake. To assess the potential ecological risk and toxicity caused by the iron-steel plant, sediment toxicity was evaluated by the PMF model, sediment quality guideline, and toxic equivalent factors. All of the three approaches suggested PAH accumulation in the NFR sediments could produce significant adverse ecological effects and half of the sediment toxicity in the NFR may be attributed to the emissions from the iron-steel plant. Some rural locations also exhibited PAH concentrations above probable effects, most likely contributed by wood/biomass burning.

5. SOUTH ELEVATION OF POWER PLANT BUILDING. GRATE COVERED 'TRASH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. SOUTH ELEVATION OF POWER PLANT BUILDING. GRATE COVERED 'TRASH RACK' VISIBLE IN CENTER. THE STEEL FRAME STRUCTURE SUPPORTS MACHINES TO CLEAR DEBRIS CAUGHT ON THE TRASH RACK. - Potomac Power Plant, On West Virginia Shore of Potomac River, about 1 mile upriver from confluence with Shenandoah River, Harpers Ferry, Jefferson County, WV

Process for dezincing galvanized steel

DOEpatents

Morgan, W.A.; Dudek, F.J.; Daniels, E.J.

1998-07-14

A process is described for removing zinc from galvanized steel. The galvanized steel is immersed in an electrolyte containing at least about 15% by weight of sodium or potassium hydroxide and having a temperature of at least about 75 C and the zinc is galvanically corroded from the surface of the galvanized steel. The material serving as the cathode is principally a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series. The corrosion rate may be accelerated by (1) increasing the number density of corrosion sites in the galvanized steel by mechanically abrading or deforming the galvanized steel, (2) heating the galvanized steel to form an alloy of zinc on the surface of the galvanized steel, (3) mixing the galvanized steel with a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series, or (4) moving the galvanized steel relative to itself and to the electrolyte while immersed in the electrolyte. 1 fig.

Process for dezincing galvanized steel

DOEpatents

Morgan, William A.; Dudek, Frederick J.; Daniels, Edward J.

1998-01-01

A process for removing zinc from galvanized steel. The galvanized steel is immersed in an electrolyte containing at least about 15% by weight of sodium or potassium hydroxide and having a temperature of at least about 75.degree. C. and the zinc is galvanically corroded from the surface of the galvanized steel. The material serving as the cathode is principally a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series. The corrosion rate may be accelerated by (i) increasing the number density of corrosion sites in the galvanized steel by mechanically abrading or deforming the galvanized steel, (ii) heating the galvanized steel to form an alloy of zinc on the surface of the galvanized steel, (iii) mixing the galvanized steel with a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series, or (iv) moving the galvanized steel relative to itself and to the electrolyte while immersed in the electrolyte.

NUCLEAR POWER PLANT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Preece, G.E.; Bell, F.R.

1963-06-26

A protective arrangement is designed for shielding the environment and for preventing the leakage of radioactive gases from a ship nuclear power plant. In this arrangement, the core has inner and outer pressure vessels and a biological shielding around the outer pressure vessel. The shielding comprises a series of steel cylindrical shells immersed in water, and its inner wall may comprise part of the outer pressure vessel. (D.L.C.)

Finite element simulation and experimental verification of steel cord extraction of steel cord conveyor belt splice

NASA Astrophysics Data System (ADS)

Li, X. G.; Long, X. Y.; Jiang, H. Q.; Long, H. B.

2018-05-01

The splice is the weakest part of the entire steel cord conveyor belt. And it occurs steel cord twitch fault frequently. If this fault cannot be dealt with timely and accurately, broken belt accidents would be occurred that affecting the safety of production seriously. In this paper, we investigate the steel cord pullout of the steel cord conveyor belt splice by using ABAQUS software. We selected the strength of steel cord conveyor belt ST630, the same as experiment sample in type specification. The finite element model consists of rubber, steel cord and failure unit. And the failure unit is used to simulate the bonding relationship between the steel cord and the rubber. Mooney-Rivlin hyper-elastic model for rubber was employed in the numerical simulations. The pullout force of length 50.0 mm single steel cord, on both sides of a single steel cord and on both sides of the double steel cords each impacted at steel cord conveyor belt splice were numerically computer and typical results obtained have been validated by experimental result. It shows that the relative error between simulation results and experimental results is within 10% and can be considered that the simulation model is reliable. A new method is provided for studying the steel cord twitch fault of the steel cord conveyor belt splice.

The Geomatics.org.UK Project

ERIC Educational Resources Information Center

Bramald, Tom; Powell, Jonathan

2006-01-01

In this article, the authors describe how pupils can benefit from some unusual and exciting free resources of geomatics.org.uk. Geomatics.org.uk is a project that provides free resources to support teaching and learning in a variety of subjects including maths and geography, often in a cross-curricular way. Via the project website, it is possible,…

Steel-reinforced concrete-filled steel tubular columns under axial and lateral cyclic loading

NASA Astrophysics Data System (ADS)

Farajpourbonab, Ebrahim; Kute, Sunil Y.; Inamdar, Vilas M.

2018-03-01

SRCFT columns are formed by inserting a steel section into a concrete-filled steel tube. These types of columns are named steel-reinforced concrete-filled steel tubular (SRCFT) columns. The current study aims at investigating the various types of reinforcing steel section to improve the strength and hysteresis behavior of SRCFT columns under axial and lateral cyclic loading. To attain this objective, a numerical study has been conducted on a series of composite columns. First, FEM procedure has been verified by the use of available experimental studies. Next, eight composite columns having different types of cross sections were analyzed. For comparison purpose, the base model was a CFT column used as a benchmark specimen. Nevertheless, the other specimens were SRCFT types. The results indicate that reinforcement of a CFT column through this method leads to enhancement in load-carrying capacity, enhancement in lateral drift ratio, ductility, preventing of local buckling in steel shell, and enhancement in energy absorption capacity. Under cyclic displacement history, it was observed that the use of cross-shaped reinforcing steel section causes a higher level of energy dissipation and the moment of inertia of the reinforcing steel sections was found to be the most significant parameter affecting the hysteresis behavior of SRCFT columns.

Structural Amorphous Steels

NASA Astrophysics Data System (ADS)

Lu, Z. P.; Liu, C. T.; Thompson, J. R.; Porter, W. D.

2004-06-01

Recent advancement in bulk metallic glasses, whose properties are usually superior to their crystalline counterparts, has stimulated great interest in fabricating bulk amorphous steels. While a great deal of effort has been devoted to this field, the fabrication of structural amorphous steels with large cross sections has remained an alchemist’s dream because of the limited glass-forming ability (GFA) of these materials. Here we report the discovery of structural amorphous steels that can be cast into glasses with large cross-section sizes using conventional drop-casting methods. These new steels showed interesting physical, magnetic, and mechanical properties, along with high thermal stability. The underlying mechanisms for the superior GFA of these materials are discussed.

Long Term Large Scale river nutrient changes across the UK

NASA Astrophysics Data System (ADS)

Bell, Victoria; Naden, Pam; Tipping, Ed; Davies, Helen; Davies, Jessica; Dragosits, Ulli; Muhammed, Shibu; Quinton, John; Stuart, Marianne; Whitmore, Andy; Wu, Lianhai

2017-04-01

During recent decades and centuries, pools and fluxes of Carbon, Nitrogen and Phosphorus (C, N and P) in UK rivers and ecosystems have been transformed by the spread and fertiliser-based intensification of agriculture (necessary to sustain human populations), by atmospheric pollution, by human waste (rising in line with population growth), and now by climate change. The principal objective of the UK's NERC-funded Macronutrients LTLS research project has been to account for observable terrestrial and aquatic pools, concentrations and fluxes of C, N and P on the basis of past inputs, biotic and abiotic interactions, and transport processes. More specifically, over the last 200 years, what have been the temporal responses of plant and soil nutrient pools in different UK catchments to nutrient enrichment, and what have been the consequent effects on nutrient transfers from land to the atmosphere, freshwaters and estuaries? The work described here addresses the second question by providing an integrated quantitative description of the interlinked land and water pools and annual fluxes of C, N and P for UK catchments over time. A national-scale modelling environment has been developed, combining simple physically-based gridded models that can be parameterised using recent observations before application to long timescales. The LTLS Integrated Model (LTLS-IM) uses readily-available driving data (climate, land-use, nutrient inputs, topography), and model estimates of both terrestrial and freshwater nutrient loads have been compared with measurements from sites across the UK. Here, the focus is on the freshwater nutrient component of the LTLS-IM, but the terrestrial nutrient inputs required for this are provided by models of nutrient processes in semi-natural and agricultural systems, and from simple models of nutrients arising from human waste. In the freshwater model, lateral routing of dissolved and particulate nutrients and within-river processing such as

17. Baltimore through truss steel bridge (1905), built by the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. Baltimore through truss steel bridge (1905), built by the American Bridge Company. The bridge is 15 to 20 feet wide, with a wooden deck, and connects the Sullivan Machine Co. with the Foundry. The enclosed bridge in the background was constructed ca. 1920, and connects the Chain Machine Building with its power plant, foundry, and pattern shop. - Sullivan Machinery Company, Main Street between Pearl & Water Streets, Claremont, Sullivan County, NH

Damascus steel ledeburite class

NASA Astrophysics Data System (ADS)

Sukhanov, D. A.; Arkhangelsky, L. B.; Plotnikova, N. V.

2017-02-01

Discovered that some of blades Damascus steel has an unusual nature of origin of the excess cementite, which different from the redundant phases of secondary cementite, cementite of ledeburite and primary cementite in iron-carbon alloys. It is revealed that the morphological features of separate particles of cementite in Damascus steels lies in the abnormal size of excess carbides having the shape of irregular prisms. Considered three hypotheses for the formation of excess cementite in the form of faceted prismatic of excess carbides. The first hypothesis is based on thermal fission of cementite of a few isolated grains. The second hypothesis is based on the process of fragmentation cementite during deformation to the separate the pieces. The third hypothesis is based on the transformation of metastable cementite in the stable of angular eutectic carbide. It is shown that the angular carbides are formed within the original metastable colony ledeburite, so they are called “eutectic carbide”. It is established that high-purity white cast iron is converted into of Damascus steel during isothermal soaking at the annealing. It was revealed that some of blades Damascus steel ledeburite class do not contain in its microstructure of crushed ledeburite. It is shown that the pattern of carbide heterogeneity of Damascus steel consists entirely of angular eutectic carbides. Believe that Damascus steel refers to non-heat-resistant steel of ledeburite class, which have similar structural characteristics with semi-heat-resistant die steel or heat-resistant high speed steel, differing from them only in the nature of excess carbide phase.

Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

NASA Astrophysics Data System (ADS)

Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

2017-11-01

The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

Austenitic-ferritic stainless steels: A state-of-the-art review

NASA Astrophysics Data System (ADS)

Voronenko, B. I.

1997-10-01

Austenitic-ferritic stainless steels, more commonly known as duplex stainless steels, or DSS for short, consist of two basic phases. One is austenite, A, and the other is ferrite, F, present in about equal amounts (but not less than 30% each). The two phases owe their corrosion resistance to the high chromium content. Compared to austenitic stainless steels, ASS, they are stronger (without sacrificing ductility), resist corrosion better, and cost less due to their relatively low nickel content. DSS can be used in an environment where standard ASS are not durable enough, such as chloride solutions (ships, petrochemical plant, etc.). Due to their low nickel content and the presence of nickel, DSS have good weldability. However, they have a limited service temperature range (from -40 to 300°) because heating may cause them to give up objectionable excess phases and lower the threshold of cold brittleness in the heat-affected zone of welded joints. State-of-the art DSS are alloyed with nitrogen to stabilize their austenite, and in this respect the nitrogen does the job of nickel. Also, nitrogen enhances the strength and resistance to pitting and improves the structure of welds.

Adaptive Granulation-Based Prediction for Energy System of Steel Industry.

PubMed

Wang, Tianyu; Han, Zhongyang; Zhao, Jun; Wang, Wei

2018-01-01

The flow variation tendency of byproduct gas plays a crucial role for energy scheduling in steel industry. An accurate prediction of its future trends will be significantly beneficial for the economic profits of steel enterprise. In this paper, a long-term prediction model for the energy system is proposed by providing an adaptive granulation-based method that considers the production semantics involved in the fluctuation tendency of the energy data, and partitions them into a series of information granules. To fully reflect the corresponding data characteristics of the formed unequal-length temporal granules, a 3-D feature space consisting of the timespan, the amplitude and the linetype is designed as linguistic descriptors. In particular, a collaborative-conditional fuzzy clustering method is proposed to granularize the tendency-based feature descriptors and specifically measure the amplitude variation of industrial data which plays a dominant role in the feature space. To quantify the performance of the proposed method, a series of real-world industrial data coming from the energy data center of a steel plant is employed to conduct the comparative experiments. The experimental results demonstrate that the proposed method successively satisfies the requirements of the practically viable prediction.

Comminuting irradiated ferritic steel

DOEpatents

Bauer, Roger E.; Straalsund, Jerry L.; Chin, Bryan A.

1985-01-01

Disclosed is a method of comminuting irradiated ferritic steel by placing the steel in a solution of a compound selected from the group consisting of sulfamic acid, bisulfate, and mixtures thereof. The ferritic steel is used as cladding on nuclear fuel rods or other irradiated components.

Health, safety, and environmental risk assessment of steel production complex in central Iran using TOPSIS.

PubMed

Jozi, S A; Majd, N Moradi

2014-10-01

This research was carried out with the aim of presenting an environmental management plan for steel production complex (SPC) in central Iran. Following precise identification of the plant activities as well as the study area, possible sources of environmental pollution and adverse impacts on the air quality, water, soil, biological environment, socioeconomic and cultural environment, and health and safety of the employees were determined considering the work processes of the steel complex. Afterwards, noise, wastewater, and air pollution sources were measured. Subsequently, factors polluting the steel complex were identified by TOPSIS and then prioritized using Excel Software. Based on the obtained results, the operation of the furnaces in hot rolling process with the score 1, effluent derived from hot rolling process with the score 0.565, nonprincipal disposal and dumping of waste at the plant enclosure with the score 0.335, walking beam process with the score 1.483 respectively allocated themselves the highest priority in terms of air, water, soil and noise pollution. In terms of habitats, land cover and socioeconomic and cultural environment, closeness to the forest area and the existence of four groups of wildlife with the score 1.106 and proximity of villages and residential areas to the plant with the score 3.771 respectively enjoyed the highest priorities while impressibility and occupational accidents with the score 2.725 and cutting and welding operations with score 2.134 had the highest priority among health and safety criteria. Finally, strategies for the control of pollution sources were identified and Training, Monitoring and environmental management plan of the SPC was prepared.

Ultrahigh Carbon Steel.

DTIC Science & Technology

1984-10-01

The unique mechanical properties achieved in UHC steels are due to the presence of micron-size ferrite grains and ultrafine spheroidized carbides. SN...unique mechanical properties achieved in UHC [0 steels are due to the presence of micron-size ferrite grains and ultrafine spheroidized carbides. 0... steel is that it has a low resistance to plastic flow upon deformation in the superplastic range at low strain rates (e.g., 2000 psi at 4 1041 e 10 s

POLLUTION EFFECTS OF ABNORMAL OPERATIONS IN IRON AND STEEL MAKING. VOLUME II. SINTERING, MANUAL OF PRACTICE

EPA Science Inventory

The report is one in a six-volume series considering abnormal operating conditions (AOCs) in the primary section (sintering, blast furnace ironmaking, open hearth, electric furnace, and basic oxygen steelmaking) of an integrated iron and steel plant. Pollution standards, generall...

The corrosion performance of high chromium stainless steels and titanium alloys at a reverse osmosis plant in Arabian Gulf seawater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Al-Odwani, A.; Al-Tabatabaei, M.; Carew, J.

1997-08-01

Electrochemical impedance spectroscopy (EIS) was used to evaluate the corrosion performance of four high chromium stainless steels and Grade 2 titanium in flowing Arabian Gulf natural seawater. The EIS provided information concerning the changes to the interfacial impedance as a function of exposure time for these alloys. The impedance spectra for all the alloys showed slight changes at the low frequency region over the exposure period. The open-circuit potentials (OCP) of these alloys were also monitored as a function of exposure time. The stainless steel alloys exhibited slight fluctuation in potential around the initial exposure potential. However, Grade 2 titaniummore » initial potential was more active and then gradually shifted towards the noble direction. The linear polarization resistance (LPR) method indicated that Grade 2 titanium exhibited the lowest corrosion rate with respect to the stainless steel alloys. The results of the EIS analysis and OCP indicated that Grade 2 titanium performed better than the four high chromium stainless steel alloys.« less

Methods of making bainitic steel materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bakas, Michael Paul; Chu, Henry Shiu-Hung; Zagula, Thomas Andrew

Methods of making bainitic steels may involve austenitizing a quantity of steel by exposing the quantity of steel to a first temperature. A composition of the quantity of steel may be configured to impede formation of non-bainite ferrite, pearlite, and Widmanstatten ferrite. The quantity of steel may be heat-treated to form bainite by exposing the quantity of steel to a second, lower temperature. The second, lower temperature may be stabilized by exposing the quantity of steel to the second, lower temperature in the presence of a thermal ballast.

Paediatric home care in the UK.

PubMed Central

Tatman, M A; Woodroffe, C

1993-01-01

Paediatric home care services in the UK were ascertained in 1991 and 1992. Respondents from 209 (97%) UK health districts and boards identified 62 general and 124 specialist paediatric home care services by January 1993, 15% having opened in the previous year. Of all UK children, 30% lived in a district with a general home care service. Five health regions had only specialist services. Districts differed widely in the availability of home care for different disorders. The home care services were small, general services employing a mean (SD) of 2.5 (1.6) whole time equivalent (WTE) nurses, and specialist services 1.3 (0.8) WTE nurses. Few services were available 24 hours a day. Funding arrangements were diverse and some services had difficulties in obtaining consumables and equipment for home use. Despite rapid growth there remains considerable scope for the development of paediatric home care throughout the UK. PMID:8285782

Optimization of BI test parameters to investigate mechanical properties of Grade 92 steel

NASA Astrophysics Data System (ADS)

Barbadikar, Dipika R.; Vincent, S.; Ballal, Atul R.; Peshwe, Dilip R.; Mathew, M. D.

2018-04-01

The ball indentation (BI) testing is used to evaluate the tensile properties of materials namely yield strength, strength coefficient, ultimate tensile strength, and strain hardening exponent. The properties evaluated depend on a number of BI test parameters. These parameters include the material constants like yield slope (YS), constraint factor (CF), yield offset parameter (YOP). Number of loading/unloading cycles, preload, indenter size and depth of penetration of indenter also affects the properties. In present investigation the effect of these parameters on the stress-strain curve of normalized and tempered Grade 92 steel is evaluated. Grade 92 is a candidate material for power plant application over austenitic stainless steel and derives its strength from M23C6, MX precipitates and high dislocation density. CF, YS and YOP changed the strength properties considerably. Indenter size effect resulted in higher strength for smaller indenter. It is suggested to use larger indenter diameter and higher number of loading cycles for GRADE 92 steel to get best results using BI technique.

The Gatsby Plant Science Summer School: inspiring the next generation of plant science researchers.

PubMed

Levesley, Aurora; Jopson, Juliet; Knight, Celia

2012-04-01

We provide evidence from a 5-year study to show that a single concerted effort at the start of undergraduate study can have a clear and lasting effect on the attitudes of students toward plant science. Attendance at a week-long residential plant science summer school in the first year of an undergraduate degree resulted in many students changing courses to include more plant science and increased numbers of graduates selecting plant-based PhDs. The evidence shows that the Gatsby Plant Science Summer School has increased the pool of high-quality plant science related PhD applicants in the UK and has had a positive impact on students' career aspirations. The results are discussed within the context of enhancing the pipeline of future plant scientists and reversing the decline of this vulnerable and strategically important subject relevant to addressing food security and other major global challenges. We have shown that a single well-designed and timely intervention can influence future student behavior and as such offers a framework of potential use to other vulnerable disciplines.

13. INTERIOR OF POWER PLANT LOOKING EASTNORTHEAST. 1925 GE GENERATOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. INTERIOR OF POWER PLANT LOOKING EAST-NORTHEAST. 1925 GE GENERATOR IN FOREGROUND, WITH C. 1910 GENERATOR COVER IN BACKGROUND. STEEL FRAME SUPPORTS HOISTING MECHANISM USED TO MOVE, REPAIR, OR REPLACE GENERATORS. - Potomac Power Plant, On West Virginia Shore of Potomac River, about 1 mile upriver from confluence with Shenandoah River, Harpers Ferry, Jefferson County, WV

The Returns to UK Degrees for Foreign-Educated Graduates

ERIC Educational Resources Information Center

Valbuena, Javier; Zhu, Yu

2018-01-01

Exploiting information on foreign qualifications for the first time, we estimate the returns to obtaining UK higher degrees for foreign graduates who migrated to the UK in their 20s. Accounting for direct measures of foreign and UK qualifications and country-of-origin fixed effects, we find substantial returns to obtaining UK (higher) degrees on…

Preconditioning with cations increases the attachment of Anoxybacillus flavithermus and Geobacillus species to stainless steel.

PubMed

Somerton, Ben; Flint, Steve; Palmer, Jon; Brooks, John; Lindsay, Denise

2013-07-01

Preconditioning of Anoxybacillus flavithermus E16 and Geobacillus sp. strain F75 with cations prior to attachment often significantly increased (P ≤ 0.05) the number of viable cells that attached to stainless steel (by up to 1.5 log CFU/cm(2)) compared with unconditioned bacteria. It is proposed that the transition of A. flavithermus and Geobacillus spp. from milk formulations to stainless steel product contact surfaces in milk powder manufacturing plants is mediated predominantly by bacterial physiological factors (e.g., surface-exposed adhesins) rather than the concentrations of cations in milk formulations surrounding bacteria.

Preconditioning with Cations Increases the Attachment of Anoxybacillus flavithermus and Geobacillus Species to Stainless Steel

PubMed Central

Flint, Steve; Palmer, Jon; Brooks, John; Lindsay, Denise

2013-01-01

Preconditioning of Anoxybacillus flavithermus E16 and Geobacillus sp. strain F75 with cations prior to attachment often significantly increased (P ≤ 0.05) the number of viable cells that attached to stainless steel (by up to 1.5 log CFU/cm2) compared with unconditioned bacteria. It is proposed that the transition of A. flavithermus and Geobacillus spp. from milk formulations to stainless steel product contact surfaces in milk powder manufacturing plants is mediated predominantly by bacterial physiological factors (e.g., surface-exposed adhesins) rather than the concentrations of cations in milk formulations surrounding bacteria. PMID:23645192

Effect of Silicon on Desulfurization of Aluminum-killed Steels

NASA Astrophysics Data System (ADS)

Roy, Debdutta

Recent reports have suggested that silicon has a beneficial effect on the rate of desulfurization of Al-killed steel. This effect is difficult to understand looking at the overall desulfurization reaction which does not include silicon. However an explanation is proposed by taking into account the (SiO2)/[Si] equilibrium in which some Al reaching the slag-metal interface is used in reducing the SiO2 in the slag. This reaction can be suppressed to some extent if the silicon content of the metal is increased and in doing so, more Al will be available at the slag-metal interface for the desulfurization reaction and this would increase the rate of the desulfurization reaction. A model was developed, assuming the rates are controlled by mass transfer, taking into account the coupled reactions of the reduction of silica, and other unstable oxides, namely iron oxide and manganese oxide, in the slag and desulfurization reaction in the steel by aluminum. The model predicts that increasing silicon increases the rate and extent of desulfurization. Plant data was analyzed to obtain rough estimates of ladle desulfurization rates and also used to validate the model predictions. Experiments have been conducted on a kilogram scale of material in an induction furnace to test the hypothesis. The major conclusions of the study are as follows: The rate and extent of desulfurization improve with increasing initial silicon content in the steel; the effect diminishes at silicon contents higher than approximately 0.2% and with increasing slag basicity. This was confirmed with kilogram-scale laboratory experiments. The effects of the silicon content in the steel (and of initial FeO and MnO in the slag) largely arise from the dominant effects of these reactions on the equilibrium aluminum content of the steel: as far as aluminum consumption or pick-up is concerned, the Si/SiO2 reaction dominates, and desulfurization has only a minor effect on aluminum consumption. The rate is primarily

High temperature corrosion of austenitic stainless steel coils in a direct reduction plant in Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Juarez-Islas, J.A.; Campillo, B.; Chaudhary, N.

1996-08-01

The subject of this study is related to the performance of austenitic steels coils and tubes, in a range of temperatures between 425 to 870 C for the transport of reducing gases, in an installation involving the direct reduction of iron-ore by reforming natural gas. Evidence is presented that metal dusting is not the only unique high temperature corrosion mechanism that caused catastrophic failures of austenitic 304 (UNS S30400) coils and HK-40 (UNS J94204) tubes. Sensitization as well as stress corrosion cracking occurred in 304 stainless steel coils, and metal dusting occurred in tubes of HK-40, a high resistance alloy.more » The role of a continuous injection of H{sub 2}S to the process is suggested to avoid the high temperature metal dusting corrosion mechanism found in these kind of installations.« less

Microstructural characterization in dissimilar friction stir welding between 304 stainless steel and st37 steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jafarzadegan, M.; State Key Laboratory of Advanced Welding Production Technology, School of Materials Science and Eng., Harbin Institute of Technology, P.O. Box: 150001, Harbin; Feng, A.H.

2012-12-15

In the present study, 3 mm-thick plates of 304 stainless steel and st37 steel were welded together by friction stir welding at a welding speed of 50 mm/min and tool rotational speed of 400 and 800 rpm. X-ray diffraction test was carried out to study the phases which might be formed in the welds. Metallographic examinations, and tensile and microhardness tests were used to analyze the microstructure and mechanical properties of the joint. Four different zones were found in the weld area except the base metals. In the stir zone of the 304 stainless steel, a refined grain structure withmore » some features of dynamic recrystallization was evidenced. A thermomechanically-affected zone was characterized on the 304 steel side with features of dynamic recovery. In the other side of the stir zone, the hot deformation of the st37 steel in the austenite region produced small austenite grains and these grains transformed to fine ferrite and pearlite and some products of displacive transformations such as Widmanstatten ferrite and martensite by cooling the material after friction stir welding. The heat-affected zone in the st37 steel side showed partially and fully refined microstructures like fusion welding processes. The recrystallization in the 304 steel and the transformations in the st37 steel enhanced the hardness of the weld area and therefore, improved the tensile properties of the joint. - Highlights: Black-Right-Pointing-Pointer FSW produced sound welds between st37 low carbon steel and 304 stainless steel. Black-Right-Pointing-Pointer The SZ of the st37 steel contained some products of allotropic transformation. Black-Right-Pointing-Pointer The material in the SZ of the 304 steel showed features of dynamic recrystallization. Black-Right-Pointing-Pointer The finer microstructure in the SZ increased the hardness and tensile strength.« less

SSTL UK-DMC SLIM-6 data quality assessment

USGS Publications Warehouse

Chander, G.; Saunier, S.; Choate, M.J.; Scaramuzza, P.L.

2009-01-01

Satellite data from the Surrey Satellite Technology Limited (SSTL) United Kingdom (UK) Disaster Monitoring Constellation (DMC) were assessed for geometric and radiometric quality. The UK-DMC Surrey Linear Imager 6 (SLIM-6) sensor has a 32-m spatial resolution and a ground swath width of 640 km. The UK-DMC SLIM-6 design consists of a three-band imager with green, red, and near-infrared bands that are set to similar bandpass as Landsat bands 2, 3, and 4. The UK-DMC data consisted of imagery registered to Landsat orthorectified imagery produced from the GeoCover program. Relief displacements within the UK-DMC SLIM-6 imagery were accounted for by using global 1-km digital elevation models available through the Global Land One-km Base Elevation (GLOBE) Project. Positional accuracy and relative band-to-band accuracy were measured. Positional accuracy of the UK-DMC SLIM-6 imagery was assessed by measuring the imagery against digital orthophoto quadrangles (DOQs), which are designed to meet national map accuracy standards at 1 : 24 000 scales; this corresponds to a horizontal root-mean-square accuracy of about 6 m. The UK-DMC SLIM-6 images were typically registered to within 1.0-1.5 pixels to the DOQ mosaic images. Several radiometric artifacts like striping, coherent noise, and flat detector were discovered and studied. Indications are that the SSTL UK-DMC SLIM-6 data have few artifacts and calibration challenges, and these can be adjusted or corrected via calibration and processing algorithms. The cross-calibration of the UK-DMC SLIM-6 and Landsat 7 Enhanced Thematic Mapper Plus was performed using image statistics derived from large common areas observed by the two sensors.

High Nitrogen Stainless Steel

DTIC Science & Technology

2011-07-19

STAINLESS STEEL by E. U. Lee R. Taylor 19 July 2011 Approved for...NAWCADPAX/TR-2011/162 19 July 2011 HIGH NITROGEN STAINLESS STEEL by E. U. Lee R. Taylor RELEASED BY...REPORT TYPE Technical Report 3. DATES COVERED 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER High Nitrogen Stainless Steel 5b. GRANT

Comparison of the performance of concrete-filled steel tubular and hollow steel diagrid buildings

NASA Astrophysics Data System (ADS)

Peter, Minu Ann; S, Sajith A.; Nagarajan, Praveen

2018-03-01

In the recent construction scenario, diagrid structures are becoming a popular high-rise building structural system. Diagrid structures consist of diagonals in the perimeter and an interior core. The corner and interior vertical columns are not required due to the structural efficiency of diagrid structural systems. Steel and concrete are commonly used material for diagrid. An alternate material for diagrid is concrete-filled steel tube (CFST). CFST incorporates the advantages of both steel and concrete. In CFST, the inward buckling of the steel tube is effectively prevented by the filled concrete. The compressive strength of concrete increases due to the tri-axial state of stress in concrete induced by the steel tube. The longitudinal as well as lateral reinforcement to the concrete core is also provided by the steel tube. This paper compares the performance of CFST and steel diagrid buildings using linear static analysis. For this purpose, a 12 storey and 36 storey building are analysed using finite element method and CFST diagrid building is found to perform better.

Molecular Diversity of Anthracnose Pathogen Populations Associated with UK Strawberry Production Suggests Multiple Introductions of Three Different Colletotrichum Species

PubMed Central

Baroncelli, Riccardo; Zapparata, Antonio; Sarrocco, Sabrina; Sukno, Serenella A.; Lane, Charles R.; Thon, Michael R.; Vannacci, Giovanni; Holub, Eric; Sreenivasaprasad, Surapareddy

2015-01-01

Fragaria × ananassa (common name: strawberry) is a globally cultivated hybrid species belonging to Rosaceae family. Colletotrichum acutatum sensu lato (s.l.) is considered to be the second most economically important pathogen worldwide affecting strawberries. A collection of 148 Colletotrichum spp. isolates including 67 C. acutatum s.l. isolates associated with the phytosanitary history of UK strawberry production were used to characterize multi-locus genetic variation of this pathogen in the UK, relative to additional reference isolates that represent a worldwide sampling of the diversity of the fungus. The evidence indicates that three different species C. nymphaeae, C. godetiae and C. fioriniae are associated with strawberry production in the UK, which correspond to previously designated genetic groups A2, A4 and A3, respectively. Among these species, 12 distinct haplotypes were identified suggesting multiple introductions into the country. A subset of isolates was also used to compare aggressiveness in causing disease on strawberry plants and fruits. Isolates belonging to C. nymphaeae, C. godetiae and C. fioriniae representative of the UK anthracnose pathogen populations showed variation in their aggressiveness. Among the three species, C. nymphaeae and C. fioriniae appeared to be more aggressive compared to C. godetiae. This study highlights the genetic and pathogenic heterogeneity of the C. acutatum s.l. populations introduced into the UK linked to strawberry production. PMID:26086351

A comprehensive emission inventory of multiple air pollutants from iron and steel industry in China: Temporal trends and spatial variation characteristics.

PubMed

Wang, Kun; Tian, Hezhong; Hua, Shenbing; Zhu, Chuanyong; Gao, Jiajia; Xue, Yifeng; Hao, Jiming; Wang, Yong; Zhou, Junrui

2016-07-15

China has become the largest producer of iron and steel throughout the world since 1996. However, as an energy-and-pollution intensive manufacturing sector, a detailed comprehensive emission inventory of air pollutants for iron and steel industry of China is still not available. To obtain and better understand the temporal trends and spatial variation characteristics of typical hazardous air pollutants (HAPs) emissions from iron and steel production in China, a comprehensive emission inventory of multiple air pollutants, including size segregated particulate matter (TSP/PM10/PM2.5), gaseous pollutants (SO2, NOx, CO), heavy metals (Pb, Cd, Hg, As, Cr, Ni etc.), as well as the more dangerous PCDD/Fs, is established with the unit-based annual activity, specific dynamic emission factors for the historical period of 1978-2011, and the future potential trends till to 2050 are forecasted by using scenario analysis. Our results show that emissions of gaseous pollutants and particulate matter have experienced a gradual increase tendency since 2000, while emissions of priority-controlled heavy metals (Hg, Pb, As, Cd, Cr, and Ni) have exhibited a short-term fluctuation during the period of 1990 to 2005. With regard to the spatial distribution of HAPs emissions in base year 2011, Bohai economic circle is identified as the top emission intensity region where iron and steel smelting plants are densely built; within iron and steel industry, blast furnaces contribute the majority of PM emissions, sinter plants account for most of gaseous pollutants and the majority of PCDD/Fs, whereas steel making processes are responsible for the majority of heavy metal emissions. Moreover, comparisons of future emission trends under three scenarios indicate that advanced technologies and integrated whole process management strategies are in great need to further diminish various hazardous air pollutants from iron and steel industry in the future. Copyright © 2016 Elsevier B.V. All rights

Challenges in Special Steel Making

NASA Astrophysics Data System (ADS)

Balachandran, G.

2018-02-01

Special bar quality [SBQ] is a long steel product where an assured quality is delivered by the steel mill to its customer. The bars have enhanced tolerance to higher stress application and it is demanded for specialised component making. The SBQ bars are sought for component making processing units such as closed die hot forging, hot extrusion, cold forging, machining, heat treatment, welding operations. The final component quality of the secondary processing units depends on the quality maintained at the steel maker end along with quality maintained at the fabricator end. Thus, quality control is ensured at every unit process stages. The various market segments catered to by SBQ steel segment is ever growing and is reviewed. Steel mills need adequate infrastructure and technological capability to make these higher quality steels. Some of the critical stages of processing SBQ and the critical quality maintenance parameters at the steel mill in the manufacture has been brought out.

[Stainless steels for medical instruments].

PubMed

Feofilov, R N

1981-01-01

Both in the USSR and abroad similar types of martensitic and austenitic stainless steel are used for the manufacture of medical instruments. Martensitic steel, the cheapest and most economically alloyed, has the best combination of properties necessary for medical instruments. The analysis of the Soviet and foreign experience in using different grades of steel for the production of medical instruments demonstrates the expediency and possibility of improving the quality of martensitic steel and rolled stock, as well as that of medical instruments manufactured from these materials, by improving, the operations of the metallurgical and technological processes and by specifying more precisely the requirements for medical instruments. The possibility and expediency of using, in some technically justified cases, lower grades of alloyed steel instead of grade 12X18H9T for clamps and other instruments made of stainless steel, as well as highly corrosive grades of steel for microinstruments, have been established.

Plant Line Trial Evaluation of Viable Non-Chromium Passivation Systems for Electrolytin Tinplate, ETP (TRP 9911)

DOE Office of Scientific and Technical Information (OSTI.GOV)

John A. Sinsel

2003-06-30

Plant trial evaluations have been completed for two zirconium-based, non-chromium passivation systems previously identified as possible alternatives to cathodic dichromate (CDC) passivation for electrolytic tinplate (ETP). These trials were done on a commercial electrolytic tin plating line at Weirton Steel and extensive evaluations of the materials resulting from these trials have been completed. All this was accomplished as a collaborative effort under the AISI Technology Roadmap Program and was executed by seven North American Tin Mill Products producers [Bethlehem Steel (now acquired by International Steel Group (ISG)), Dofasco Inc., National Steel (now acquired by U.S. Steel), U.S. Steel, USS-Posco, Weirtonmore » Steel, and Wheeling-Pittsburgh Steel] with funding partially from the Department of Energy (DOE) and partially on an equal cost sharing basis among project participants. The initial phases of this project involved optimization of application procedures for the non-chromium systems in the laboratories at Bethlehem Steel and Betz Dearborn followed by extensive testing with various lacquer formulations and food simulants in the laboratories at Valspar and PPG. Work was also completed at Dofasco and Weirton Steel to develop methods to prevent precipitation of insoluble solids as a function of time from the zirconate system. The results of this testing indicated that sulfide staining characteristics for the non-chromium passivation systems could be minimized but not totally eliminated and neither system was found to perform quite as good, in this respect, as the standard CDC system. As for the stability of zirconate treatment, a method was developed to stabilize this system for a sufficient period of time to conduct plant trial evaluations but, working with a major supplier of zirconium orthosulfate, a method for long term stabilization is still under development.« less

The Gatsby Plant Science Summer School: Inspiring the Next Generation of Plant Science Researchers[OA

PubMed Central

Levesley, Aurora; Jopson, Juliet; Knight, Celia

2012-01-01

We provide evidence from a 5-year study to show that a single concerted effort at the start of undergraduate study can have a clear and lasting effect on the attitudes of students toward plant science. Attendance at a week-long residential plant science summer school in the first year of an undergraduate degree resulted in many students changing courses to include more plant science and increased numbers of graduates selecting plant-based PhDs. The evidence shows that the Gatsby Plant Science Summer School has increased the pool of high-quality plant science related PhD applicants in the UK and has had a positive impact on students’ career aspirations. The results are discussed within the context of enhancing the pipeline of future plant scientists and reversing the decline of this vulnerable and strategically important subject relevant to addressing food security and other major global challenges. We have shown that a single well-designed and timely intervention can influence future student behavior and as such offers a framework of potential use to other vulnerable disciplines. PMID:22534129

Thermal Plasma Spheroidization of High-Nitrogen Stainless Steel Powder Alloys Synthesized by Mechanical Alloying

NASA Astrophysics Data System (ADS)

Razumov, Nikolay G.; Popovich, Anatoly A.; Wang, QingSheng

2018-03-01

This paper presents the results of experimental studies on the treatment of Fe-23Cr-11Mn-1N high-nitrogen stainless steel powder alloys, synthesized by the mechanical alloying (MA) of elemental powders in the flow of a thermal plasma. Fe-23Cr-11Mn-1N high-nitrogen stainless steel powder alloys were prepared by MA in the attritor under an argon atmosphere. For spheroidization of Fe-23Cr-11Mn-1N high-nitrogen stainless steel powder alloys, the TekSphero 15 plant manufactured by Tekna Plasma Systems Inc was used. The studies have shown the possibility of obtaining Fe-23Cr-11Mn-1N high-nitrogen spherical powders steel alloys from the powder obtained by MA. According to the results of a series of experiments, it was found that the results of plasma spheroidization of powders essentially depend on the size of the fraction due to some difference in the particle shape and flowability, and on the gas regime of the plasma torch. It is established that during the plasma spheroidization process, some of the nitrogen leaves the alloy. The loss rate of nitrogen depends on the size of the initial particles.

29 CFR 1926.754 - Structural steel assembly.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing bars...

29 CFR 1926.754 - Structural steel assembly.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing bars...

Science education reforms in the UK.

PubMed

2012-10-01

As children return to school at the end of the summer in the UK, planned reforms aim to increase their science and maths literacy. A comprehensive foundation in these essential subjects is necessary to ensure that the UK remains at the forefront of science and technology for decades to come.

1. LOOKING NORTH AT THE BASIC OXYGEN STEELMAKING PLANT. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. LOOKING NORTH AT THE BASIC OXYGEN STEELMAKING PLANT. THE FLUX HANDLING BUILDING IS ON THE RIGHT, THE MOULD CONDITIONING BUILDING IS IN THE CENTER, THE BASIC OXYGEN PROCESS (BOP) SHOP IS IN THE CENTER BACKGROUND, AND OPEN HEARTH No. 2 BUILDING IS ON THE LEFT. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Steel Industry Wastes.

ERIC Educational Resources Information Center

Schmidtke, N. W.; Averill, D. W.

1978-01-01

Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

Small scale spatial gradients of outdoor and indoor benzene in proximity of an integrated steel plant.

PubMed

Licen, Sabina; Tolloi, Arianna; Briguglio, Sara; Piazzalunga, Andrea; Adami, Gianpiero; Barbieri, Pierluigi

2016-05-15

Benzene is known as a human carcinogen, whose annual mean concentration exceeded the EU limit value (5 μg/m(3)) only in very few locations in Europe during 2012. Nevertheless 10% to 12% of the EU-28 urban population was still exposed to benzene concentrations above the WHO reference level of 1.7 μg/m(3). WHO recommended a wise choice of monitoring stations positioning in proximity of "hot spots" to define and assess the representativeness of each site paying attention to micro-scale conditions. In this context benzene and other VOCs of health concern (toluene, ethylbenzene, xylenes) concentrations have been investigated, with weekly passive sampling for one year, both in outdoor and indoor air in inhabited buildings in close proximity (180 m far up to 1100 m) of an integrated steel plant in NE of Italy. Even though the outdoor mean annual benzene concentration was below the EU limit in every site, in the site closest to the works the benzene concentration was above 5 μg/m(3) in 14 weeks. These events were related to a benzene over toluene ratio above one, which is diagnostic for the presence of an industrial source, and to meteorological factors. These information pointed at the identification of the coke ovens of the plant as the dominant outdoor source of benzene. Benzene gradients with the increasing distance from coke ovens have been found for both outdoor and indoor air. Linear models linking outdoor to indoor benzene concentrations have been then identified, allowing to estimate indoor exposure from ambient air benzene data. In the considered period, a narrow area of about 250 m appeared impacted at a higher degree than the other sites both considering outdoor and indoor air. Passive BTEX sampling permits to collect information on both ambient air and daily life settings, allowing to assemble a valuable data support for further environmental cost-benefit analyses. Copyright © 2016 Elsevier B.V. All rights reserved.

Modeling of Liquid Steel/Slag/Argon Gas Multiphase Flow During Tundish Open Eye Formation in a Two-Strand Tundish

NASA Astrophysics Data System (ADS)

Chatterjee, Saikat; Li, Donghui; Chattopadhyay, Kinnor

2018-04-01

Multiphase flows are frequently encountered in metallurgical operations. One of the most effective ways to understand these processes is by flow modeling. The process of tundish open eye (TOE) formation involves three-phase interaction between liquid steel, slag, and argon gas. The two-phase interaction involving argon gas bubbles and liquid steel can be modeled relatively easily using the discrete phase modeling technique. However, the effect of an upper slag layer cannot be captured using this approach. The presence of an upper buoyant phase can have a major effect on the behavior of TOEs. Hence, a multiphase model, including three phases, viz. liquid steel, slag, and argon gas, in a two-strand slab caster tundish, was developed to study the formation and evolution of TOEs. The volume of fluid model was used to track the interphase between liquid steel and slag phases, while the discrete phase model was used to trace the movement of the argon gas bubbles in liquid steel. The variation in the TOE areas with different amounts of aspirated argon gas was examined in the presence of an overlying slag phase. The mathematical model predictions were compared against steel plant measurements.

Stress Corrosion Behavior of 12Cr Martensite Steel for Steam Turbine LP Blade

NASA Astrophysics Data System (ADS)

Tianjian, Wang; Yubing, Pei; Zhenhuan, Gao; Hua, Fan; Gongxian, Yang

With the development of capacity and efficiency of coal-fired thermal power plant, the length of Low Pressure (LP) last-stage blade of steam turbine became longer. Therefore, the design static stress of blade gets closer or even higher than the yield strength of material. Because of the special operation condition of LP last stage blade, the stress corrosion crack of 12Cr-Ni-Mo-V-N Martensite stainless steel may happen especially at the root of the blade where designed the highest static stress. In this paper, the stress corrosion behavior of 12Cr-Ni-Mo-V-N Martensite stainless steels used for steam turbine LP last stage blade in 3vol% NaCl solution was studied, the constant stress is about 95%, 85%, 65% and 35% of yield stress respectively and the test was lasted for 3000 hours, the stress corrosion behavior was studied and then, the effect of shot penning strengthen for anti-stress corrosion property of 12Cr-Ni-Mo-V-N Martensitic steel was studied. The results showed that the purity of steel affects the stress corrosion behavior huge especially at the high and medium stress condition. The shot penning cannot enhances the anti-stress corrosion property of the 12Cr-Ni-Mo-V-N steel at high tensile constant stress condition, however it will make the anti-stress corrosion property better when the stress is low.

Does carbonation of steel slag particles reduce their toxicity? An in vitro approach.

PubMed

Ibouraadaten, Saloua; van den Brule, Sybille; Lison, Dominique

2015-06-01

Mineral carbonation can stabilize industrial residues and, in the steel industry, may contribute to simultaneously valorize CO2 emissions and slag. We hypothesized that, by restricting the leaching of metals of toxicological concern such as Cr and V, carbonation can suppress the toxicity of these materials. The cytotoxic activity (WST1 assay) of slag dusts collected from a stainless and a Linz-Donawitz (LD) steel plant, before and after carbonation, was examined in J774 macrophages. The release of Cr, V, Fe, Mn and Ni was measured after incubation in artificial lung fluids mimicking the extracellular and phagolysosomal milieu to which particles are confronted after inhalation. LD slag had the higher Fe, Mn and V content, and was more cytotoxic than stainless steel slag. The cytotoxic activity of LD but not of stainless dusts was reduced after carbonation. The cytotoxic activity of the dusts toward J774 macrophages necessitated a direct contact with the cells and was reduced in the presence of inhibitors of phagocytosis (cytochalasin D) or phagolysosome acidification (bafilomycin), pointing to a key role of metallic constituents released in phagolysosomes. This in vitro study supports a limited reduction of the cytotoxic activity of LD, but not of stainless, steel dusts upon carbonation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Stainless steel reinforcement as a replacement for epoxy coated steel in bridge decks : final report.

DOT National Transportation Integrated Search

2013-08-01

The corrosion resistance of 2304 stainless steel reinforcement and stainless steel clad reinforcement was compared to conventional and epoxy-coated reinforcement (ECR). 2304 stainless steel was tested in both the as-received condition (dark mottled f...

Impacts of Steel-Slag-Based Silicate Fertilizer on Soil Acidity and Silicon Availability and Metals-Immobilization in a Paddy Soil

PubMed Central

Ning, Dongfeng; Liang, Yongchao; Liu, Zhandong; Xiao, Junfu; Duan, Aiwang

2016-01-01

Slag-based silicate fertilizer has been widely used to improve soil silicon- availability and crop productivity. A consecutive early rice-late rice rotation experiment was conducted to test the impacts of steel slag on soil pH, silicon availability, rice growth and metals-immobilization in paddy soil. Our results show that application of slag at a rate above higher or equal to 1 600 mg plant-available SiO2 per kg soil increased soil pH, dry weight of rice straw and grain, plant-available Si concentration and Si concentration in rice shoots compared with the control treatment. No significant accumulation of total cadmium (Cd) and lead (Pb) was noted in soil; rather, the exchangeable fraction of Cd significantly decreased. The cadmium concentrations in rice grains decreased significantly compared with the control treatment. In conclusion, application of steel slag reduced soil acidity, increased plant–availability of silicon, promoted rice growth and inhibited Cd transport to rice grain in the soil-plant system. PMID:27973585

The use and impact of intraplant trading in the iron and steel industry to reduce water pollution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kashmanian, R.M.; Podar, M.K.; Luttner, M.A.

1995-12-01

Economists have long proposed that market forces could be harnessed to achieve environmental goals more efficiently than regulations typically used. However, there have been few opportunities to test this concept in practice. The authors investigate the use and impact of one example of incentive-based environmental regulation. For more than ten years, the US Environmental Protection Agency has permitted iron and steel plants to distribute facility-wide water pollutant discharge limits among outfalls in whatever manner is determined by the plant to be least expensive. Although this intra-plant trading system is highly regulated to ensure environmental goals are achieved, it nonetheless servesmore » as an excellent test case of the economic theory. At least ten iron and steel facilities have incorporated intra-plant trading in their discharge permits, with five trades still active. Estimates obtained from seven facilities indicate trading resulted in accumulated total savings compared to traditional technology-based limits of at least $122.7 million (1993 dollars), including capital and annual operation and maintenance costs. The net pollutant reductions permitted under trading range from less than one pound per day for most trades involving lead and zinc to several thousand pounds per day for some trades involving total suspended solids.« less

The future of learning disabilities nursing in the UK.

PubMed

Clapham, Anthony

2014-07-02

This article appraises the report Strengthening the Commitment, which is a UK-wide review of learning disabilities nursing by the UK's four chief nursing officers. Strengthening the Commitment has strategic importance in reviewing progress in the care of people with learning disabilities in the UK. It also has a role in helping to guide future strategies and initiatives addressing the continuing health inequalities experienced by people with learning disabilities throughout the UK.

Grade Inflation in UK Higher Education

ERIC Educational Resources Information Center

Bachan, Ray

2017-01-01

This paper examines the continual increase in the proportion of "good" honour degrees awarded by UK universities since the mid-2000s. This trend has brought with it the charge of "grade inflation" that may reflect falling standards in UK higher education. This issue has been raised in the national press and in government which…

Review on cold-formed steel connections.

PubMed

Lee, Yeong Huei; Tan, Cher Siang; Mohammad, Shahrin; Tahir, Mahmood Md; Shek, Poi Ngian

2014-01-01

The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed.

Review on Cold-Formed Steel Connections

PubMed Central

Tan, Cher Siang; Mohammad, Shahrin; Md Tahir, Mahmood; Shek, Poi Ngian

2014-01-01

The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed. PMID:24688448

Molten salt thermal energy storage subsystem for Solar Thermal Central Receiver plants

NASA Astrophysics Data System (ADS)

Wells, P. B.; Nassopoulos, G. P.

The development of a low-cost thermal energy storage subsystem for large solar plants is analyzed. Molten nitrate salt is used as both the plant's working fluid and as the storage medium. The storage system comprises a specially designed hot tank to hold salt at a storage temperature of 839 K (1050 F) and a separate carbon steel cold tank to hold the salt after its thermal energy has been extracted to generate steam. The hot tank is lined with insulating firebrick to lower the shell temperature to 561 K (550 F) so that a low-cost carbon steel shell can be used. A preliminary design is described for a large commercial-size plant (1200 MWht). Also described are a laboratory test program for the critical components and the design, construction, and test of a small-scale research experiment at the Central Receiver Test Facility in Albuquerque, New Mexico.

The risk of hydraulic fracturing on public health in the UK and the UK's fracking legislation.

PubMed

Reap, Elisabeth

2015-01-01

Hydraulic fracturing to extract natural gas from shale rock is a new, rapidly expanding industry in the United States (US). However, there is concern that these operations could be having large negative impacts such as groundwater contamination, increased air pollution and seismic events. The United Kingdom (UK) is looking at the potential for emulating the success of 'shale gas' in the US. Differences in population density and geological conditions mean that the public health impacts recorded in the US cannot be directly extrapolated to the UK. There is limited academic literature available but findings suggest that the UK government is not fully recognising the inherent risks of hydraulic fracturing exposed by this literature. Government reports suggest a reliance on engineering solutions and better practice to overcome problems found in the US when evidence suggests that there are inherent risks and impacts that cannot be eliminated. This study applies US results to approximate the impact of one exposure pathway, inhalation of hydrocarbons by the public from operational air emissions over the 30 year lifetime of a well and finds that 7.2 extra cancer cases from exposure to air contamination would be expected in the UK if all test sites, approved test sites and test sites awaiting approval as of January 2015 went on to extract gas. In conclusion, limited assessment of the public health implications of hydraulic fracturing operations is available but the UK government appears to not be applying the precautionary principle to potentially significant legislation.

A Sustainable Approach for Optimal Steel Sheet Pile Structure Assessment, Maintenance, and Rehabilitation

DTIC Science & Technology

2011-09-30

plants, electrical transmission network, pipelines) • public buildings (e.g., schools, hospitals, post offices, police stations, fire houses, court...developed under REMR focused on concrete and steel materials, along with geotechnical, hydraulic, electrical and mechanical, environmental, and coastal...between the wet or dry kilning processes in ce- ment production cannot be discerned from the overall impacts associ- ated with concrete production. The

Cold resistant nickel-alloy steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Legostaev, Yu.L.; Karchevskaya, N.I.; Karchevnikov, V.P.

1988-05-01

Low-alloy cold-resistant steel 10GNB was developed for the construction of ships and floating drill rigs. The optimal heat-treatment regime for the steel was refinement. Reducing the carbon content improved its weldability and toughness properties. Optical metallography and electron microscopy established that the optimal structure was a tempered martensitic-bainitic mixture with uniformly distributed particles of disperse special niobium carbides NbC. The substructure and the processes of carbide and carbonitride phase segregation were studied by transmission and extraction electron microscopy. In mechanical tests the steel exhibited high resistance to brittle failure. In terms of corrosion resistance the steel corresponds to the requirementsmore » set forth for shipbuilding steels.« less

Investigation of the magnetic properties of Si-gradient steel sheet by comparison with 6.5%Si steel sheet

NASA Astrophysics Data System (ADS)

Hiratani, T.; Zaizen, Y.; Oda, Y.; Yoshizaki, S.; Senda, K.

2018-05-01

In this study, we investigated the magnetic properties of Si-gradient steel sheet produced by CVD (chemical vapor deposition) siliconizing process, comparing with 6.5% Si steel sheet. The Si-gradient steel sheet having silicon concentration gradient in the thickness direction, has larger hysteresis loss and smaller eddy current loss than the 6.5% Si steel sheet. In such a loss configuration, the iron loss of the Si-gradient steel sheet becomes lower than that of the 6.5% Si steel sheet at high frequencies. The experiment suggests that tensile stress is formed at the surface layer and compressive stress is formed at the inner layer in the Si gradient steel sheet. The magnetic anisotropy is induced by the internal stress and it is considered to affect the magnetization behavior of the Si-gradient steel sheet. The small eddy current loss of Si-gradient steel sheet can be explained as an effect of magnetic flux concentration on the surface layer.

POLLUTION EFFECTS OF ABNORMAL OPERATIONS IN IRON AND STEEL MAKING. VOLUME V. ELECTRIC ARC FURNACE, MANUAL OF PRACTICE

EPA Science Inventory

The report is one in a six-volume series considering abnormal operating conditions (AOCs) in the primary section (sintering, blast furnace ironmaking, open hearth, electric furnace, and basic oxygen steelmaking) of an integrated iron and steel plant. Pollution standards, generall...

POLLUTION EFFECTS OF ABNORMAL OPERATIONS IN IRON AND STEEL MAKING. VOLUME III. BLAST FURNACE IRONMAKING, MANUAL OF PRACTICE

EPA Science Inventory

The report is one in a six-volume series considering abnormal operating conditions (AOCs) in the primary section (sintering, blast furnace ironmaking, open hearth, electric furnace, and basic oxygen steelmaking) of an integrated iron and steel plant. Pollution standards, generall...

POLLUTION EFFECTS OF ABNORMAL OPERATIONS IN IRON AND STEEL MAKING. VOLUME IV. OPEN HEARTH FURNACE, MANUAL OF PRACTICE

EPA Science Inventory

The report is one in a six-volume series considering abnormal operating conditions (AOCs) in the primary section (sintering, blast furnace ironmaking, open hearth, electric furnace, and basic oxygen steelmaking) of an integrated iron and steel plant. Pollution standards, generall...

POLLUTION EFFECTS OF ABNORMAL OPERATIONS IN IRON AND STEEL MAKING. VOLUME VI. BASIC OXYGEN PROCESS, MANUAL OF PRACTICE

EPA Science Inventory

The report is one in a six-volume series considering abnormal operating conditions (AOCs) in the primary section (sintering, blast furnace ironmaking, open hearth, electric furnace, and basic oxygen steelmaking) of an integrated iron and steel plant. Pollution standards, generall...

Processing and refinement of steel microstructure images for assisting in computerized heat treatment of plain carbon steel

NASA Astrophysics Data System (ADS)

Gupta, Shubhank; Panda, Aditi; Naskar, Ruchira; Mishra, Dinesh Kumar; Pal, Snehanshu

2017-11-01

Steels are alloys of iron and carbon, widely used in construction and other applications. The evolution of steel microstructure through various heat treatment processes is an important factor in controlling properties and performance of steel. Extensive experimentations have been performed to enhance the properties of steel by customizing heat treatment processes. However, experimental analyses are always associated with high resource requirements in terms of cost and time. As an alternative solution, we propose an image processing-based technique for refinement of raw plain carbon steel microstructure images, into a digital form, usable in experiments related to heat treatment processes of steel in diverse applications. The proposed work follows the conventional steps practiced by materials engineers in manual refinement of steel images; and it appropriately utilizes basic image processing techniques (including filtering, segmentation, opening, and clustering) to automate the whole process. The proposed refinement of steel microstructure images is aimed to enable computer-aided simulations of heat treatment of plain carbon steel, in a timely and cost-efficient manner; hence it is beneficial for the materials and metallurgy industry. Our experimental results prove the efficiency and effectiveness of the proposed technique.

High Level Manpower and Technological Change in the Steel Industry: Implications for Corporate Manpower Planning.

ERIC Educational Resources Information Center

Hiestand, Dale L.

The purpose of this study was to examine the role that high level manpower plays in the establishment of new technologies at the plant and industry level. The steel industry was selected as an appropriate industry to approach these questions due to: its considerable technological changes; its straightforward, easier-to-understand technology; its…

The carbon component of the UK power price

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kris Voorspools

2006-08-01

CO{sub 2} emissions trading is in full swing in Europe and is already having an impact on the price of power in the UK. If EU allowances (EUAs) trade at euro 20/t-CO{sub 2}, the EUA component in the power price is estimated to be slightly < euro 10/MW.h. In the case of UK power for delivery 1 year ahead, this is {approximately} 10% of the market price of power. The introduction of a carbon components into the UK power prices took place along before the 'official' start of ETS in 2005. Analysis of historical data of the price of power,more » gas, coal and EUAs shows that the first trace of a CO{sub 2} component in UK power dates back to August 2003, shortly after EUAs first started to trade. In April 2004, CO{sub 2} was fully integrated into the UK power price. 4 refs., 5 figs.« less

Development of the UK Engagement Survey

ERIC Educational Resources Information Center

Kandiko Howson, Camille; Buckley, Alex

2017-01-01

Student engagement has become a key feature of UK higher education, but until recently there has been a lack of data to track, benchmark and drive enhancement. In 2015 the first full administration ran in the UK a range of survey items drawn from the US-based National Survey of Student Engagement (NSSE). This is the latest example of international…

Current forgings and their properties for steam generator of nuclear plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsukada, Hisashi; Suzuki, Komei; Kusuhashi, Mikio

1997-12-31

Current steel forgings for steam generator (SG) of PWR plant are reviewed in the aspect of design and material improvement. The following three items are introduced. The use of integral type steel forgings for the fabrication of steam generator enhances the structural integrity and makes easier fabrication and inspection including in-service inspection. The following examples of current integral type forgings developed by the Japan Steel Works, Ltd. (JSW) are introduced: (1) primary head integrated with nozzles, manways and supports; (2) steam drum head integrated with nozzle and handhole; (3) conical shell integrated with cylindrical sections and handholes. In order tomore » decrease the weight of steam generator, the high strength materials such as SA508, Cl.3a steel have been adopted in some cases. The properties of this steel are introduced and the chemistry and heat treatment condition are discussed. As one of the methods to minimize the macro- and micro-segregations, the use of vacuum carbon deoxidation (VCD), i.e. deoxidization of steel by gaseous CO reaction, with addition of Al for grain refining was investigated. The properties of SA508, Cl.3 steels with Low Si content are compared with those of conventional one.« less

US Steel Gary Works land based pushing emissions control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Randolph, R.A.; Price, C.A.

1983-01-01

To meet air quality standards at its Gary Works Coke Plant in Gary, Indiana, US Steel Corporation has installed pushing emission control systems for its five (77) oven, three meter coke batteries. The pushing emission control system consists of a hooded coke guide, single spot catch car, stationary emission capture ducts and remote gas cleaning baghouse with precoat capabilities. The system is providing effective emission control. In addition, there are corollary benefits. The operation of the single spot catch cars is easier and safer and coke moisture variables have been reduced.

"Legal highs" on the net-Evaluation of UK-based Websites, products and product information.

PubMed

Schmidt, Martin M; Sharma, Akhilesh; Schifano, Fabrizio; Feinmann, Charlotte

2011-03-20

A vast array of substances are marketed as "legal highs" in the UK. These products are mainly marketed online and are packaged and produced to mimic illicit drugs. Little is known about the full range of products available at present and no studies have evaluated the product information provided to consumers. AIMS & HYPOTHESIS: To describe the available legal high products marketed by UK-based Internet retailers and evaluate the product information provided to consumers. Websites were identified using the terms "buy legal highs+UK" and two search engines. The first 100 hits and a random sample of 5% of the remaining results were screened. Websites based in the UK were included and all products were entered on a database. Information on product name, list price, claimed effects, side effects, contraindications and interactions was extracted. A descriptive analysis was conducted using SPSS v14. 115 Websites met the inclusion criteria but due to duplicate listings this was reduced to 39 unique Websites. 1308 products were found and evaluated. The average product price was 9.69 British pounds. Products took the form of pills (46.6%), smoking material (29.7%) and single plant material/extract (18.1%). Most products claimed to be stimulants (41.7%), sedatives (32.3%), or hallucinogens (12.9%). 40.1% of products failed to list ingredients, 91.9% failed to list side effects, 81.9% failed to list contraindications and 86.3% failed to list drug interactions. Top 5 products (with active ingredients in brackets) by frequency were Salvia divinorum (Salivinorin A), Kratom (Mitragynine), Hawaiian Baby Woodrose Seeds (Lysergic Acid Amide), Fly Agaric (Ibotenic Acid, Muscimol) and Genie (JWH018, CP47497). Products marketed as "legal highs" are easily available from UK-based Internet retailers and are reasonably affordable. Safety information provided to consumers is poor. Uninformed users risk serious adverse effects. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Prediction of external corrosion for steel cylinders at the Paducah Gaseous Diffusion Plant: Application of an empirical method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyon, B.F.

1996-02-01

During the summer of 1995, ultrasonic wall thickness data were collected for 100 steel cylinders containing depleted uranium (DU) hexafluoride located at Paducah Gaseous Diffusion Plant (PGDP) in Paducah, Kentucky. The cylinders were selected for measurement to assess the condition of the more vulnerable portion of the cylinder inventory at PGDP. The purpose of this report is to apply the method used in Lyon to estimate the effects of corrosion for larger unsampled populations as a function of time. The scope of this report is limited and is not intended to represent the final analyses of available data. Future effortsmore » will include continuing analyses of available data to investigate defensible deviations from the conservative assumptions made to date. For each cylinder population considered, two basic types of analyses were conducted: (1) estimates were made of the number of cylinders as a function of time that will have a minimum wall thickness of either 0 mils (1 mil = 0.00 1 in.) or 250 mils and (2) the current minimum wall thickness distributions across cylinders were estimated for each cylinder population considered. Additional analyses were also performed investigating comparisons of the results for F and G yards with the results presented in Lyon (1995).« less

Biofortification of UK food crops with selenium.

PubMed

Broadley, Martin R; White, Philip J; Bryson, Rosie J; Meacham, Mark C; Bowen, Helen C; Johnson, Sarah E; Hawkesford, Malcolm J; McGrath, Steve P; Zhao, Fang-Jie; Breward, Neil; Harriman, Miles; Tucker, Mark

2006-05-01

Se is an essential element for animals. In man low dietary Se intakes are associated with health disorders including oxidative stress-related conditions, reduced fertility and immune functions and an increased risk of cancers. Although the reference nutrient intakes for adult females and males in the UK are 60 and 75 microg Se/d respectively, dietary Se intakes in the UK have declined from >60 microg Se/d in the 1970s to 35 microg Se/d in the 1990s, with a concomitant decline in human Se status. This decline in Se intake and status has been attributed primarily to the replacement of milling wheat having high levels of grain Se and grown on high-Se soils in North America with UK-sourced wheat having low levels of grain Se and grown on low-Se soils. An immediate solution to low dietary Se intake and status is to enrich UK-grown food crops using Se fertilisers (agronomic biofortification). Such a strategy has been adopted with success in Finland. It may also be possible to enrich food crops in the longer term by selecting or breeding crop varieties with enhanced Se-accumulation characteristics (genetic biofortification). The present paper will review the potential for biofortification of UK food crops with Se.

UK114, a YjgF/Yer057p/UK114 family protein highly conserved from bacteria to mammals, is localized in rat liver peroxisomes.

PubMed

Antonenkov, Vasily D; Ohlmeier, Steffen; Sormunen, Raija T; Hiltunen, J Kalervo

2007-05-25

Mammalian UK114 belongs to a highly conserved family of proteins with unknown functions. Although it is believed that UK114 is a cytosolic or mitochondrial protein there is no detailed study of its intracellular localization. Using analytical subcellular fractionation, electron microscopic colloidal gold technique, and two-dimensional gel electrophoresis of peroxisomal matrix proteins combined with mass spectrometric analysis we show here that a large portion of UK114 is present in rat liver peroxisomes. The peroxisomal UK114 is a soluble matrix protein and it is not inducible by the peroxisomal proliferator clofibrate. The data predict involvement of UK114 in peroxisomal metabolism.

A-3 steel work completed

NASA Image and Video Library

2009-04-09

Stennis Space Center engineers celebrated a key milestone in construction of the A-3 Test Stand on April 9 - completion of structural steel work. Workers with Lafayette (La.) Steel Erector Inc. placed the last structural steel beam atop the stand during a noon ceremony attended by more than 100 workers and guests.

A-3 steel work completed

NASA Technical Reports Server (NTRS)

2009-01-01

Stennis Space Center engineers celebrated a key milestone in construction of the A-3 Test Stand on April 9 - completion of structural steel work. Workers with Lafayette (La.) Steel Erector Inc. placed the last structural steel beam atop the stand during a noon ceremony attended by more than 100 workers and guests.

A nondestructive method for estimation of the fracture toughness of CrMoV rotor steels based on ultrasonic nonlinearity.

PubMed

Jeong, Hyunjo; Nahm, Seung-Hoon; Jhang, Kyung-Young; Nam, Young-Hyun

2003-09-01

The objective of this paper is to develop a nondestructive method for estimating the fracture toughness (K(IC)) of CrMoV steels used as the rotor material of steam turbines in power plants. To achieve this objective, a number of CrMoV steel samples were heat-treated, and the fracture appearance transition temperature (FATT) was determined as a function of aging time. Nonlinear ultrasonics was employed as the theoretical basis to explain the harmonic generation in a damaged material, and the nonlinearity parameter of the second harmonic wave was the experimental measure used to be correlated to the fracture toughness of the rotor steel. The nondestructive procedure for estimating the K(IC) consists of two steps. First, the correlations between the nonlinearity parameter and the FATT are sought. The FATT values are then used to estimate K(IC) using the K(IC) versus excess temperature (i.e., T-FATT) correlation that is available in the literature for CrMoV rotor steel.

Development of Advanced 9Cr Ferritic-Martensitic Steels and Austenitic Stainless Steels for Sodium-Cooled Fast Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sham, Sam; Tan, Lizhen; Yamamoto, Yukinori

2013-01-01

Ferritic-martensitic (FM) steel Grade 92, with or without thermomechanical treatment (TMT), and austenitic stainless steels HT-UPS (high-temperature ultrafine precipitate strengthening) and NF709 were selected as potential candidate structural materials in the U.S. Sodium-cooled Fast Reactor (SFR) program. The objective is to develop advanced steels with improved properties as compared with reference materials such as Grade 91 and Type 316H steels that are currently in nuclear design codes. Composition modification and/or processing optimization (e.g., TMT and cold-work) were performed to improve properties such as resistance to thermal aging, creep, creep-fatigue, fracture, and sodium corrosion. Testings to characterize these properties for themore » advanced steels were conducted by the Idaho National Laboratory, the Argonne National Laboratory and the Oak Ridge National Laboratory under the U.S. SFR program. This paper focuses on the resistance to thermal aging and creep of the advanced steels. The advanced steels exhibited up to two orders of magnitude increase in creep life compared to the reference materials. Preliminary results on the weldment performance of the advanced steels are also presented. The superior performance of the advanced steels would improve reactor design flexibility, safety margins and economics.« less

Larson-Miller Constant of Heat-Resistant Steel

NASA Astrophysics Data System (ADS)

Tamura, Manabu; Abe, Fujio; Shiba, Kiyoyuki; Sakasegawa, Hideo; Tanigawa, Hiroyasu

2013-06-01

Long-term rupture data for 79 types of heat-resistant steels including carbon steel, low-alloy steel, high-alloy steel, austenitic stainless steel, and superalloy were analyzed, and a constant for the Larson-Miller (LM) parameter was obtained in the current study for each material. The calculated LM constant, C, is approximately 20 for heat-resistant steels and alloys except for high-alloy martensitic steels with high creep resistance, for which C ≈ 30 . The apparent activation energy was also calculated, and the LM constant was found to be proportional to the apparent activation energy with a high correlation coefficient, which suggests that the LM constant is a material constant possessing intrinsic physical meaning. The contribution of the entropy change to the LM constant is not small, especially for several martensitic steels with large values of C. Deformation of such martensitic steels should accompany a large entropy change of 10 times the gas constant at least, besides the entropy change due to self-diffusion.

Cost viability of 3D printed house in UK

NASA Astrophysics Data System (ADS)

Tobi, A. L. Mohd; Omar, S. A.; Yehia, Z.; Al-Ojaili, S.; Hashim, A.; Orhan, O.

2018-03-01

UK has been facing housing crisis due to the rising price of the property on sale. This paper will look into the viability of 3D printing technology as an alternative way for house construction on UK. The analysis will be carried out based on the data until the year of 2014 due to limited resources availability. Details cost breakdown on average size house construction cost in UK were analysed and relate to the cost viability of 3D printing technology in reducing the house price in UK. It is found that the 3D printing generates saving of up to around 35% out of total house price in UK. This cost saving comes from the 3D printed construction of walls and foundations for material and labour cost.

Scientific and Technological Principles of Development of New Cold-Resistant Arc-Steels (Steels for Arctic Applications)

NASA Astrophysics Data System (ADS)

Sych, O. V.; Khlusova, E. I.; Yashin, E. A.

2017-12-01

The paper presents the results of quantitative analysis of C, Mn, Ni and Cu content on strength and cold-resistance of rolled plates. Relations between the ferritic-bainitic structure morphology and anisotropy and steel performance characteristics have been established. Influence of thermal and deformation rolling patterns on steel structure has been studied. The steel chemical composition has been improved and precision thermomechanical processing conditions for production of cold-resistant Arc-steel plates have been developed.

Project SEARCH UK - Evaluating Its Employment Outcomes.

PubMed

Kaehne, Axel

2016-11-01

The study reports the findings of an evaluation of Project SEARCH UK. The programme develops internships for young people with intellectual disabilities who are about to leave school or college. The aim of the evaluation was to investigate at what rate Project SEARCH provided employment opportunities to participants. The evaluation obtained data from all sites operational in the UK at the time of evaluation (n = 17) and analysed employment outcomes. Data were available for 315 young people (n = 315) in the programme and pay and other employment related data were available for a subsample. The results of the analysis suggest that Project SEARCH achieves on average employment rates of around 50 per cent. Project SEARCH UK represents a valuable addition to the supported employment provision in the UK. Its unique model should inform discussions around best practice in supported employment. Implications for other supported employment programmes are discussed. © 2015 John Wiley & Sons Ltd.

Superhard Nanocrystalline Homometallic Stainless Steel on Steel for Seamless Coatings

NASA Technical Reports Server (NTRS)

Tobin, Eric J.; Hafley, R. (Technical Monitor)

2002-01-01

The objective of this work is to deposit nanocrystalline stainless steel onto steel substrates (homometallic) for enhanced wear and corrosion resistance. Homometallic coatings provide superior adhesion, and it has been shown that ultrafine-grained materials exhibit the increased hardness and decreased permeability desired for protective coatings. Nanocrystals will be produced by controlling nucleation and growth and use of an ion beam during deposition by e-beam evaporation or sputtering. Phase I is depositing 31 6L nanocrystalline stainless steel onto 31 6L stainless steel substrates. These coatings exhibit hardnesses comparable to those normally obtained for ceramic coatings such ZrO2, and possess the superior adhesion of seamless, homometallic coatings. Hardening the surface with a similar material also enhances adhesion, by avoiding problems associated with thermal and lattice mismatch. So far we have deposited nanocrystalline homometallic 316L stainless steel coatings by varying the ions and the current density of the ion beams. For all deposition conditions we have produced smooth, uniform, superhard coatings. All coatings exhibit hardness of at least 200% harder than that of bulk materials. Our measurements indicate that there is a direct relationship between nanohardness and the current density of the ion beam. Stress measurements indicate that stress in the films is increasingly proportional to current density of the ion beam. TEM, XPS, and XRD results indicate that the coated layers consist of FCC structure nanocrystallites with a dimension of about 10 to 20 nm. The Ni and Mo concentration of these coating are lower than those of bulk 316L but the concentration of Cr is higher.

Use of cold-bonded, waste oxide briquettes at U.S. Steel Mon Valley BOP shop

DOE Office of Scientific and Technical Information (OSTI.GOV)

DiCaprio, V.; Howell, K.; Harris, R.

1995-09-01

In attempts to avoid the escalated costs and environmental concerns associated with taking waste oxide materials to a landfill, National Recovery Systems Inc., in conjunction with US Steel, built a waste oxide briquetting facility at the USS Mon Valley works (Edgar Thomson plant) to recycle various sludges and scales. The waste oxide briquette is currently a blend of BOP classifier sludge, BOP filter drum sludge, casterscale and hot strip mill scale. In addition to the landfill cost avoidance, the waste oxide briquette is also a low cast, steel scrap supplement. This paper describes the production of the waste oxide briquettemore » and the use of the recycled material at the Edgar Thomson BOP shop.« less

Heavy-section steel irradiation program. Semiannual progress report, October 1995--March 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corwin, W.R.

1997-04-01

Maintaining the integrity of the reactor pressure vessel (RPV) in a light-water-cooled nuclear power plant is crucial in preventing and controlling severe accidents which have the potential for major contamination release. The RPV is the only key safety-related component of the plant for which a duplicate or redundant backup system does not exist. It is therefore imperative to understand and be able to predict the capabilities and limitations of the integrity inherent in the RPV. In particular, it is vital to fully understand the degree of irradiation-induced degradation of the RPVs fracture resistance which occurs during service, since without thatmore » radiation damage, it is virtually impossible to postulate a realistic scenario that would result in RPV failure. For this reason, the Heavy-Section Steel Irradiation (HSSI) Program has been established with its primary goal to provide a thorough, quantitative assessment of the effects of neutron irradiation on the material behavior and, in particular, the fracture toughness properties of typical pressure-vessel steels as they relate to light-water RPV integrity. Effects of specimen size; material chemistry; product form and microstructure; irradiation fluence, flux, temperature, and spectrum; and postirradiation annealing are being examined on a wide range of fracture properties.« less

Finite element residual stress analysis of induction heating bended ferritic steel piping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kima, Jong Sung; Kim, Kyoung-Soo; Oh, Young-Jin

2014-10-06

Recently, there is a trend to apply the piping bended by induction heating process to nuclear power plants. Residual stress can be generated due to thermo-mechanical mechanism during the induction heating bending process. It is well-known that the residual stress has important effect on crack initiation and growth. The previous studies have focused on the thickness variation. In part, some studies were performed for residual stress evaluation of the austenitic stainless steel piping bended by induction heating. It is difficult to find the residual stresses of the ferritic steel piping bended by the induction heating. The study assessed the residualmore » stresses of induction heating bended ferriticsteel piping via finite element analysis. As a result, it was identified that high residual stresses are generated on local outersurface region of the induction heating bended ferritic piping.« less

Leadership Practices in German and UK Organisations

ERIC Educational Resources Information Center

McCarthy, Grace

2005-01-01

Purpose: The aim of this research was to determine whether leadership practices vary between German and UK organisations. Design/methodology/approach: The author used self-assessment documents submitted by German and UK organisations to the European Foundation for Quality Management (EFQM), to identify leadership practices in both countries. A…

Semen quality and sex hormones among mild steel and stainless steel welders: a cross sectional study.

PubMed Central

Bonde, J P

1990-01-01

Welding may be detrimental to the male reproductive system. To test this hypothesis, semen quality was examined in 35 stainless steel welders, 46 mild steel welders, and 54 non-welding metal workers and electricians. These figures represent a participation rate of 37.1% in welders and 36.7% in non-welding subjects. The mean exposure to welding fume particulates was 1.3 mg/m3 (SD 0.8) in stainless steel welders using tungsten inert gas, 3.2 mg/m3 (SD 1.0) in low exposed mild steel welders using manual metal arc or metal active gas (n = 31), and 4.7 mg/m3 (SD 2.1) in high exposed mild steel welders (n = 15). The semen quality of each participant was defined in terms of the mean values of the particular semen parameters in three semen samples delivered at monthly intervals in a period with occupational exposure in a steady state. The sperm concentration was not reduced in either mild steel or stainless steel welders. The sperm count per ejaculate, the proportion of normal sperm forms, the degree of sperm motility, and the linear penetration rate of the sperm were significantly decreased and the sperm concentration of follicle stimulating hormone (FSH) was non-significantly increased in mild steel welders. A dose response relation between exposure to welding fumes and these semen parameters (sperm count excepted) was found. Semen quality decreased and FSH concentrations increased with increasing exposure. Significant deteriorations in some semen parameters were also observed in stainless steel welders. An analysis of information from questionnaires obtained from the whole population including subjects who declined to participate indicated an underestimation of effects due to selection bias. Potential confounding was treated by restriction and statistical analysis. The results support the hypothesis that mild steel welding and to a lesser extent stainless steel welding with tungsten inert gas is associated with reduced semen quality at exposure in the range of the

Semen quality and sex hormones among mild steel and stainless steel welders: a cross sectional study.

PubMed

Bonde, J P

1990-08-01

Welding may be detrimental to the male reproductive system. To test this hypothesis, semen quality was examined in 35 stainless steel welders, 46 mild steel welders, and 54 non-welding metal workers and electricians. These figures represent a participation rate of 37.1% in welders and 36.7% in non-welding subjects. The mean exposure to welding fume particulates was 1.3 mg/m3 (SD 0.8) in stainless steel welders using tungsten inert gas, 3.2 mg/m3 (SD 1.0) in low exposed mild steel welders using manual metal arc or metal active gas (n = 31), and 4.7 mg/m3 (SD 2.1) in high exposed mild steel welders (n = 15). The semen quality of each participant was defined in terms of the mean values of the particular semen parameters in three semen samples delivered at monthly intervals in a period with occupational exposure in a steady state. The sperm concentration was not reduced in either mild steel or stainless steel welders. The sperm count per ejaculate, the proportion of normal sperm forms, the degree of sperm motility, and the linear penetration rate of the sperm were significantly decreased and the sperm concentration of follicle stimulating hormone (FSH) was non-significantly increased in mild steel welders. A dose response relation between exposure to welding fumes and these semen parameters (sperm count excepted) was found. Semen quality decreased and FSH concentrations increased with increasing exposure. Significant deteriorations in some semen parameters were also observed in stainless steel welders. An analysis of information from questionnaires obtained from the whole population including subjects who declined to participate indicated an underestimation of effects due to selection bias. Potential confounding was treated by restriction and statistical analysis. The results support the hypothesis that mild steel welding and to a lesser extent stainless steel welding with tungsten inert gas is associated with reduced semen quality at exposure in the range of the

CONSTRUCTION PROGRESS PHOTO OF HOT PILOT PLANT (CP640) LOOKING NORTHWEST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CONSTRUCTION PROGRESS PHOTO OF HOT PILOT PLANT (CP-640) LOOKING NORTHWEST SHOWING FORMING AND PLACEMENT OF REINFORCING STEEL FOR SOUTH WALLS OF CELLS 1, 3, 4 AND 5 AND WEST WALL FOR CELLS 1 AND 2; CONSTRUCTION 13 PERCENT COMPLETE. INL PHOTO NUMBER NRTS 59-6436. J. Anderson, Photographer, 12/18/1959 - Idaho National Engineering Laboratory, Idaho Chemical Processing Plant, Fuel Reprocessing Complex, Scoville, Butte County, ID

The cost of pressure ulcers in the UK.

PubMed

Bennett, Gerry; Dealey, Carol; Posnett, John

2004-05-01

To estimate the annual cost of treating pressure ulcers in the UK. Costs were derived from a bottom-up methodology, based on the daily resources required to deliver protocols of care reflecting good clinical practice. Health and social care system in the UK. Patients developing a pressure ulcer. A bottom-up costing approach is used to estimate treatment cost per episode of care and per patient for ulcers of different grades and level of complications. Also, total treatment cost to the health and social care system in the UK. The cost of treating a pressure ulcer varies from pound 1,064 (Grade 1) to pound 10,551 (Grade 4). Costs increase with ulcer grade because the time to heal is longer and because the incidence of complications is higher in more severe cases. The total cost in the UK is pound 1.4- pound 2.1 billion annually (4% of total NHS expenditure). Most of this cost is nurse time. Pressure ulcers represent a very significant cost burden in the UK. Without concerted effort this cost is likely to increase in the future as the population ages. To the extent that pressure ulcers are avoidable, pressure damage may be indicative of clinical negligence and there is evidence that litigation could soon become a significant threat to healthcare providers in the UK, as it is in the USA.

Research investments for UK infectious disease research 1997-2013: A systematic analysis of awards to UK institutions alongside national burden of disease.

PubMed

Head, Michael G; Brown, Rebecca J; Clarke, Stuart C

2018-01-01

Infectious disease remains a significant burden in the UK and the focus of significant amounts of research investment each year. The Research Investments in Global Health study has systematically assessed levels of funding for infection research, and here considers investment alongside UK burden of individual infectious diseases. The study included awards to UK institutions between 1997 and 2013 that were related to infectious disease. Awards related to global health projects were excluded here. UK burden data (mortality, years lived with disability, and disability adjusted life years) was sourced from the Global Burden of Disease study (IHME, USA). Awards were categorised by pathogen, disease, disease area and by type of science along the research pipeline (pre-clinical, phase I-III trials, product development, public health, cross-disciplinary research). New metrics present relative levels of funding by comparing sum investment with measures of disease burden. There were 5685 relevant awards comprising investment of £2.4 billion. By disease, HIV received most funding (£369.7m; 15.6% of the total investment). Pre-clinical science was the predominant type of science (£1.6 billion, 68.7%), with the UK Medical Research Council (MRC) the largest funder (£714.8 million, 30.1%). There is a broad temporal trend to increased fundingper annum. Antimicrobial resistance received (£102.8 million, 4.2%), whilst sepsis received £23.6 million (1.0%). Compared alongside disease burden, acute hepatitis C and measles typically were relatively well-funded, whilst pneumonia, syphilis and gonorrhoea were poorly-funded. The UK has a broad research portfolio across a wide range of infectious diseases and disciplines. There are notable strengths including HIV, some respiratory infections and in pre-clinical science, though there was less funding for UK-relevant trials and public health research. Compared to the UK burden of disease, syphilis, gonorrhoea and pneumonia appear

Steel Shear Walls, Behavior, Modeling and Design

NASA Astrophysics Data System (ADS)

Astaneh-Asl, Abolhassan

2008-07-01

In recent years steel shear walls have become one of the more efficient lateral load resisting systems in tall buildings. The basic steel shear wall system consists of a steel plate welded to boundary steel columns and boundary steel beams. In some cases the boundary columns have been concrete-filled steel tubes. Seismic behavior of steel shear wall systems during actual earthquakes and based on laboratory cyclic tests indicates that the systems are quite ductile and can be designed in an economical way to have sufficient stiffness, strength, ductility and energy dissipation capacity to resist seismic effects of strong earthquakes. This paper, after summarizing the past research, presents the results of two tests of an innovative steel shear wall system where the boundary elements are concrete-filled tubes. Then, a review of currently available analytical models of steel shear walls is provided with a discussion of capabilities and limitations of each model. We have observed that the tension only "strip model", forming the basis of the current AISC seismic design provisions for steel shear walls, is not capable of predicting the behavior of steel shear walls with length-to-thickness ratio less than about 600 which is the range most common in buildings. The main reasons for such shortcomings of the AISC seismic design provisions for steel shear walls is that it ignores the compression field in the shear walls, which can be significant in typical shear walls. The AISC method also is not capable of incorporating stresses in the shear wall due to overturning moments. A more rational seismic design procedure for design of shear walls proposed in 2000 by the author is summarized in the paper. The design method, based on procedures used for design of steel plate girders, takes into account both tension and compression stress fields and is applicable to all values of length-to-thickness ratios of steel shear walls. The method is also capable of including the effect of

The UK Haemophilia Doctors Organisation triennial audit of UK Comprehensive Care Haemophilia Centres.

PubMed

Wilde, J T

2012-07-01

Under the auspices of the United Kingdom Haemophilia Doctors Organisation (UKHCDO) the UK Comprehensive Care Haemophilia Centres (CCCs) have undergone a three yearly formal audit assessment since 1993. This report describes the evolution of the audit process and details the findings of the most recent audit round, the sixth since inception. The audit reports from the 2009 audit round were reviewed by the audit organizing group and a structured analysis of the data was compiled. CCCs in the UK offer a high standard of comprehensive care services. The main areas of concern were the state of the premises (seven centres), lack of dental services (seven centres), physiotherapy (seven centres) and social work support (11 centres). Major concerns were identified at eight centres requiring a formal letter from the chairman of UKHCDO to the chief executive of the host trust. Since inception of the triennial audit process centre report recommendations have resulted in major improvements in the services available at UK CCCs. The audit process is considered to be a highly effective means of improving the quality of care for patients with bleeding disorders and can be used as a model for the introduction of a similar process in other countries. © 2012 Blackwell Publishing Ltd.

Microstructure and Mechanical Properties of Plasma Arc Brazed AISI 304L Stainless Steel and Galvanized Steel Plates

NASA Astrophysics Data System (ADS)

Jin, Yajuan; Li, Ruifeng; Yu, Zhishui; Wang, Yu

2016-04-01

Plasma arc brazing is used to join the AISI 304L stainless steel and galvanized steel plate butt joints with the CuSi3Mn1 filler wire. The effect of parameters on weld surface appearance, interfacial microstructure, and composition distribution in the joint was studied. The microhardness and mechanical tests were conducted to determine the mechanical properties of the welded specimens. The results indicated that good appearance, bead shape, and sufficient metallurgical bonding could be obtained when the brazing process was performed with a wire feeding speed of 0.8 m/min, plasma gas flow rate of 3.0 l/min, welding current of 100 A, and welding speed of 27 cm/min. During plasma arc brazing process, the top corner of the stainless steel and galvanized steel plate were heated and melted, and the melted quantity of stainless steel was much more than that of the galvanized steel due to the thermal conductivity coefficient difference between the dissimilar materials. The microhardness test results shows that the microhardness value gradually increased from the side of the galvanized steel to the stainless steel in the joint, and it is good for improving the mechanical properties of joint. The tensile strength was a little higher than that of the brazing filler, and the fracture position of weld joint was at the base metal of galvanized steel plate.

Dietary Intake of High-Protein Foods and Other Major Foods in Meat-Eaters, Poultry-Eaters, Fish-Eaters, Vegetarians, and Vegans in UK Biobank.

PubMed

Bradbury, Kathryn E; Tong, Tammy Y N; Key, Timothy J

2017-12-02

Vegetarian diets are defined by the absence of meat and fish, but differences in the intake of other foods between meat-eaters and low or non-meat eaters are also important to document. We examined intakes of high-protein foods (meat, poultry, fish, legumes, nuts, vegetarian protein alternatives, dairy products, and eggs) and other major food groups (fruit, vegetables, bread, pasta, rice, snack foods, and beverages) in regular meat-eaters, low meat-eaters, poultry-eaters, fish-eaters, vegetarians, and vegans of white ethnicity participating in UK Biobank who had completed at least one web-based 24-h dietary assessment ( n = 199,944). In regular meat-eaters, around 25% of total energy came from meat, fish, dairy and plant milk, cheese, yogurt, and eggs. In vegetarians, around 20% of energy came from dairy and plant milk, cheese, yoghurt, eggs, legumes, nuts, and vegetarian protein alternatives, and in vegans around 15% came from plant milk, legumes, vegetarian alternatives, and nuts. Low and non-meat eaters had higher intakes of fruit and vegetables and lower intakes of roast or fried potatoes compared to regular meat-eaters. The differences in the intakes of meat, plant-based high-protein foods, and other foods between meat-eaters and low and non-meat eaters in UK Biobank may contribute to differences in health outcomes.

Dietary Intake of High-Protein Foods and Other Major Foods in Meat-Eaters, Poultry-Eaters, Fish-Eaters, Vegetarians, and Vegans in UK Biobank

PubMed Central

2017-01-01

Vegetarian diets are defined by the absence of meat and fish, but differences in the intake of other foods between meat-eaters and low or non-meat eaters are also important to document. We examined intakes of high-protein foods (meat, poultry, fish, legumes, nuts, vegetarian protein alternatives, dairy products, and eggs) and other major food groups (fruit, vegetables, bread, pasta, rice, snack foods, and beverages) in regular meat-eaters, low meat-eaters, poultry-eaters, fish-eaters, vegetarians, and vegans of white ethnicity participating in UK Biobank who had completed at least one web-based 24-h dietary assessment (n = 199,944). In regular meat-eaters, around 25% of total energy came from meat, fish, dairy and plant milk, cheese, yogurt, and eggs. In vegetarians, around 20% of energy came from dairy and plant milk, cheese, yoghurt, eggs, legumes, nuts, and vegetarian protein alternatives, and in vegans around 15% came from plant milk, legumes, vegetarian alternatives, and nuts. Low and non-meat eaters had higher intakes of fruit and vegetables and lower intakes of roast or fried potatoes compared to regular meat-eaters. The differences in the intakes of meat, plant-based high-protein foods, and other foods between meat-eaters and low and non-meat eaters in UK Biobank may contribute to differences in health outcomes. PMID:29207491

Modern steels for light automobiles (review)

NASA Astrophysics Data System (ADS)

Tikhonov, A. K.

1994-10-01

The article considers the directions of work at VAZ together with metallurgists of the CIS for creating highly efficient economically-alloyed and microalloyed steels; highly ductile forged steels with improved corrosion resistance coated with zinc and with good stamping, welding, and painting capacity. Steels are created for petrol tanks with aluminum-zinc coatings instead of lead, and new heat and corrosion-resistant steels are developed for automobile exhaust gas systems.

A Comparison of Iron and Steel Production Energy Use and Energy Intensity in China and the U.S.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasanbeigi, Ali; Price, Lynn; Aden, Nathaniel

steel industry, and final steel product mix in both countries. The share of lower energy intensity electric arc furnace production in each country was a key determinant of total steel sector energy efficiency. Overall steel sector structure, in terms of average plant vintage and production capacity, is also an important variable though data were not available to quantify this in a scenario. The methodology developed in this report, along with the accompanying quantitative and qualitative analyses, provides a foundation for comparative international assessment of steel sector energy intensity.« less

Equine uveitis: a UK perspective.

PubMed

Lowe, R C

2010-03-01

Uveitis in the equine population of the UK does not appear to be as prevalent or disastrous as seen across regions of Europe and the USA. Some cases perceived to be recurrent uveitis may be poorly resolved single episodes of uveitis and care should be taken not to make the diagnosis of recurrence without ensuring effective control of the initial episode. Leptospira spp. appear to play only a minor role ERU in the UK which is probably the main reason for the prevalence of the disease being much lower compared to the USA and mainland Europe. Actual data are relatively few on the ground as far as disease surveillance in concerned. This has 2 implications. Firstly unless we are able to effectively monitor the levels of uveitic disease, it will be difficult to pick up early changes in the trend which may allow quicker intervention. Secondly, it is difficult to secure funding for further research if the prevalence of the problem is poorly defined. This may leave the UK equine population at risk should the disease profile suddenly alter for the worse.

Efficient anti-corrosive coating of cold-rolled steel in a seawater environment using an oil-based graphene oxide ink.

PubMed

Singhbabu, Y N; Sivakumar, B; Singh, J K; Bapari, H; Pramanick, A K; Sahu, Ranjan K

2015-05-07

We report the production of an efficient anti-corrosive coating of cold-rolled (CR) steel in a seawater environment (∼3.5 wt% NaCl aqueous solution) using an oil-based graphene oxide ink. The graphene oxide was produced by heating Aeschynomene aspera plant as a carbon source at 1600 °C in an argon atmosphere. The ink was prepared by cup-milling the mixture of graphene oxide and sunflower oil for 10 min. The coating of ink on the CR steel was made using the dip-coating method, followed by curing at 350 °C for 10 min in air atmosphere. The results of the potentiodynamic polarization show that the corrosion rate of bare CR steel decreases nearly 10,000-fold by the ink coating. Furthermore, the salt spray test results show that the red rusting in the ink-coated CR steel is initiated after 100 h, in contrast to 24 h and 6 h in the case of oil-coated and bare CR steel, respectively. The significant decrease in the corrosion rate by the ink-coating is discussed based on the impermeability of graphene oxide to the corrosive ions.

UK Schools, CCTV and the Data Protection Act 1998

ERIC Educational Resources Information Center

Taylor, Emmeline

2011-01-01

The use of CCTV in schools is now commonplace in the UK. It is estimated that 85% of all UK secondary schools currently have CCTV systems in operation. The introduction of the Data Protection Act 1998 (DPA) (enacted in March 2000) meant that for the first time CCTV had direct legislation governing its use in the UK. This paper attempts to apply…

[Studies on the recovery of pharmaceutical drug substances from surfaces made of defined stainless-steel alloys].

PubMed

Kloss, S; Müller, U; Oelschläger, H

2005-09-01

Facilities for the manufacturing of pharmaceutical drug substances on the pilot-plant and the industrial scale as well as chemical reactors and vessels used for chemical work-up mainly consist of alloyed stainless steel. The influence of the alloy composition and the surface condition, i.e. of the roughness of the stainless-steel materials, on the adsorption of structurally diverse steroidal substances and, hence, on the quality of the products was studied. In general, stainless-steel alloys with smooth, not so rough surfaces are to be favored as reactor material. However, it was demonstrated in this study that, on account of the weak interaction between active substances and steel materials, mechanically polished materials of a medium roughness up to approx. 0.4 microm can be employed instead of the considerably more cost-intensive electrochemically polished stainless-steel surfaces. The type of surface finishing up to a defined roughness, then, has no influence on the quality of these pharmaceutical products. Substances that, because of their molecular structure, can function as "anions" in the presence of polar solvents, are adsorbed on very smooth surfaces prepared by electrochemical methods, forming an amorphous surface film. For substances with this structural characteristics, the lower-cost mechanically polished reactor materials of a medium roughness up to approx. 0.5 microm should be used exclusively.

Performance Steel Castings

DTIC Science & Technology

2012-09-30

Development of Sand Properties 103 Advanced Modeling Dataset.. 105 High Strength Low Alloy (HSLA) Steels 107 Steel Casting and Engineering Support...to achieve the performance goals required for new systems. The dramatic reduction in weight and increase in capability will require high performance...for improved weapon system reliability. SFSA developed innovative casting design and manufacturing processes for high performance parts. SFSA is

Development of a parent version of the Manchester-Minneapolis quality of life survey for use by parents and carers of UK children: MMQL-UK (PF)

PubMed Central

Hutchings, Hayley A; Upton, Penney; Cheung, Wai-Yee; Maddocks, Alison; Eiser, Christine; Williams, John G; Russell, Ian T; Jackson, Sonia; Jenney, Meriel EM

2008-01-01

Background Although it is now widely endorsed that children should as far as possible rate their own health related quality of life (HRQL), there are situations where proxy information on child HRQL may be useful, especially where a child is too ill or young to provide their own HRQL assessment. There is limited availability of generic HRQL scales that have a parallel child and parent version and that are reliable, valid, brief, comprehensible and suitable for use in UK populations. The aims of this study were therefore to develop and validate a parent version of the anglicised Manchester-Minneapolis Quality of Life child form (MMQL-UK (CF)) and to determine the level of association between the child and parent versions of this form. Methods This study was undertaken concurrently with the anglicisation and validation of the MMQL, a measure of HRQL developed for use with children in North America. At that time, no parent version existed, so the MMQL form for children (MMQL-UK (CF)) was used as the basis for the development of the MMQL-UK parent form (PF). The sample included a control group of healthy children and their parents and five exemplar groups; children diagnosed with asthma, diabetes or inflammatory bowel disease and their parents, children in remission from cancer and their parents and children in public care and their carers. Consistency of the MMQL-UK (PF) components were assessed by calculating Cronbach's alpha. Validation of the parent questionnaire was undertaken by comparing MMQL-UK (PF) component scores with comparable components on the proxy PedsQL™ quality of life scales, comparing MMQL-UK (PF) component scores between parents of healthy and chronic disease children and by comparison of component scores from children and their parents or carers. Reproducibility and responsiveness were assessed by retesting parents by follow-up questionnaires. Results A total of 874 children (completing MMQL-UK (CF)) and 572 parents or carers (completing MMQL-UK

High strength, tough alloy steel

DOEpatents

Thomas, Gareth; Rao, Bangaru V. N.

1979-01-01

A high strength, tough alloy steel is formed by heating the steel to a temperature in the austenite range (1000.degree.-1100.degree. C.) to form a homogeneous austenite phase and then cooling the steel to form a microstructure of uniformly dispersed dislocated martensite separated by continuous thin boundary films of stabilized retained austenite. The steel includes 0.2-0.35 weight % carbon, at least 1% and preferably 3-4.5% chromium, and at least one other substitutional alloying element, preferably manganese or nickel. The austenite film is stable to subsequent heat treatment as by tempering (below 300.degree. C.) and reforms to a stable film after austenite grain refinement.

Learning the law: practical proposals for UK medical education.

PubMed

Margetts, J K

2016-02-01

Ongoing serious breaches in medical professionalism might be avoided if UK doctors rethink their approach to law. UK medical education has a role in creating a climate of change by re-examining how law is taught to medical students. Adopting a more insightful approach in the UK to the impact of The Human Rights Act and learning to manipulate legal concepts, such as conflict of interest, need to be taught to medical students now if UK doctors are to manage complex decision-making in the NHS of the future. The literature is reviewed from a unique personal perspective of a doctor and lawyer, and practical proposals for developing medical education in law in the UK are suggested. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Development of High Heat Input Welding High Strength Steel Plate for Oil Storage Tank in Xinyu Steel Company

NASA Astrophysics Data System (ADS)

Zhao, Hemin; Dong, Fujun; Liu, Xiaolin; Xiong, Xiong

This essay introduces the developed high-heat input welding quenched and tempered pressure vessel steel 12MnNiVR for oil storage tank by Xinyu Steel, which passed the review by the Boiler and Pressure Vessel Standards Technical Committee in 2009. The review comments that compared to the domestic and foreign similar steel standard, the key technical index of enterprise standard were in advanced level. After the heat input of 100kJ/cm electro-gas welding, welded points were still with excellent low temperature toughness at -20°C. The steel plate may be constructed for oil storage tank, which has been permitted by thickness range from 10 to 40mm, and design temperature among -20°C-100°C. It studied microstructure genetic effects mechanical properties of the steel. Many production practices indicated that the mechanical properties of products and the steel by stress relief heat treatment of steel were excellent, with pretreatment of hot metal, converter refining, external refining, protective casting, TMCP and heat treatment process measurements. The stability of performance and matured technology of Xinyu Steel support the products could completely service the demand of steel constructed for 10-15 million cubic meters large oil storage tank.

Corrosion behavior of 2205 duplex stainless steel.

PubMed

Platt, J A; Guzman, A; Zuccari, A; Thornburg, D W; Rhodes, B F; Oshida, Y; Moore, B K

1997-07-01

The corrosion of 2205 duplex stainless steel was compared with that of AISI type 316L stainless steel. The 2205 stainless steel is a potential orthodontic bracket material with low nickel content (4 to 6 wt%), whereas the 316L stainless steel (nickel content: 10 to 14 wt%) is a currently used bracket material. Both stainless steels were subjected to electrochemical and immersion (crevice) corrosion tests in 37 degrees C, 0.9 wt% sodium chloride solution. Electrochemical testing indicates that 2205 has a longer passivation range than 316L. The corrosion rate of 2205 was 0.416 MPY (milli-inch per year), whereas 316L exhibited 0.647 MPY. When 2205 was coupled to 316L with equal surface area ratio, the corrosion rate of 2205 reduced to 0.260 MPY, indicating that 316L stainless steel behaved like a sacrificial anode. When 316L is coupled with NiTi, TMA, or stainless steel arch wire and was subjected to the immersion corrosion test, it was found that 316L suffered from crevice corrosion. On the other hand, 2205 stainless steel did not show any localized crevice corrosion, although the surface of 2205 was covered with corrosion products, formed when coupled to NiTi and stainless steel wires. This study indicates that considering corrosion resistance, 2205 duplex stainless steel is an improved alternative to 316L for orthodontic bracket fabrication when used in conjunction with titanium, its alloys, or stainless steel arch wires.

Tobacco imagery on prime time UK television.

PubMed

Lyons, Ailsa; McNeill, Ann; Britton, John

2014-05-01

Smoking in films is a common and well documented cause of youth smoking experimentation and uptake and hence a significant health hazard. The extent of exposure of young people to tobacco imagery in television programming has to date been far less investigated. We have therefore measured the extent to which tobacco content occurs in prime time UK television, and estimated exposure of UK youth. The occurrence of tobacco, categorised as actual tobacco use, implied tobacco use, tobacco paraphernalia, other reference to tobacco, tobacco brand appearances or any of these, occurring in all prime time broadcasting on the five most popularly viewed UK television stations during 3 separate weeks in 2010 were measured by 1-minute interval coding. Youth exposure to tobacco content in the UK was estimated using media viewing figures. Actual tobacco use, predominantly cigarette smoking, occurred in 73 of 613 (12%) programmes, particularly in feature films and reality TV. Brand appearances were rare, occurring in only 18 programmes, of which 12 were news or other factual genres, and 6 were episodes of the same British soap opera. Tobacco occurred with similar frequency before as after 21:00, the UK watershed for programmes suitable for youth. The estimated number of incidences of exposure of the audience aged less than 18 years for any tobacco, actual tobacco use and tobacco branding were 59 million, 16 million and 3 million, respectively on average per week. Television programming is a source of significant exposure of youth to tobacco imagery, before and after the watershed. Tobacco branding is particularly common in Coronation Street, a soap opera popular among youth audiences. More stringent controls on tobacco in prime time television therefore have the potential to reduce the uptake of youth smoking in the UK.

Tobacco imagery on prime time UK television

PubMed Central

Lyons, Ailsa; McNeill, Ann; Britton, John

2014-01-01

Background Smoking in films is a common and well documented cause of youth smoking experimentation and uptake and hence a significant health hazard. The extent of exposure of young people to tobacco imagery in television programming has to date been far less investigated. We have therefore measured the extent to which tobacco content occurs in prime time UK television, and estimated exposure of UK youth. Methods The occurrence of tobacco, categorised as actual tobacco use, implied tobacco use, tobacco paraphernalia, other reference to tobacco, tobacco brand appearances or any of these, occurring in all prime time broadcasting on the five most popularly viewed UK television stations during 3 separate weeks in 2010 were measured by 1-minute interval coding. Youth exposure to tobacco content in the UK was estimated using media viewing figures. Findings Actual tobacco use, predominantly cigarette smoking, occurred in 73 of 613 (12%) programmes, particularly in feature films and reality TV. Brand appearances were rare, occurring in only 18 programmes, of which 12 were news or other factual genres, and 6 were episodes of the same British soap opera. Tobacco occurred with similar frequency before as after 21:00, the UK watershed for programmes suitable for youth. The estimated number of incidences of exposure of the audience aged less than 18 years for any tobacco, actual tobacco use and tobacco branding were 59 million, 16 million and 3 million, respectively on average per week. Conclusions Television programming is a source of significant exposure of youth to tobacco imagery, before and after the watershed. Tobacco branding is particularly common in Coronation Street, a soap opera popular among youth audiences. More stringent controls on tobacco in prime time television therefore have the potential to reduce the uptake of youth smoking in the UK. PMID:23479113

Accelerated technology transfer: the UK quantum initiative

NASA Astrophysics Data System (ADS)

Bennett, Simon D.

2016-10-01

A new generation of quantum technology based systems, exploiting effects such as superposition and entanglement, will enable widespread, highly disruptive applications which are expected to be of great economic significance. However, the technology is only just emerging from the physics laboratory and generally remains at low TRLs. The question is: where, and when, will this impact be first manifest? The UK, with substantial Government backing, has embarked on an ambitious national program to accelerate the process of technology transfer with the objective of seizing a significant and sustainable share of the future economic benefit for the UK. Many challenges and uncertainties remain but the combined and co-ordinated efforts of Government, Industry and Academia are making great progress. The level of collaboration is unusually high and the goal of embedding a "QT Ecosystem" in the UK looks to be attainable. This paper describes the UK national programme, its key players, and their respective roles. It will illustrate some of the likely first commercial applications and provide a status update. Some of the challenges that might prevent realisation of the goal will be highlighted.

Spatial mapping of lead, arsenic, iron, and polycyclic aromatic hydrocarbon soil contamination in Sydney, Nova Scotia: community impact from the coke ovens and steel plant.

PubMed

Lambert, Timothy W; Boehmer, Jennifer; Feltham, Jason; Guyn, Lindsay; Shahid, Rizwan

2011-01-01

This paper presents spatial maps of the arsenic, lead, and polycyclic aromatic hydrocarbon (PAH) soil contamination in Sydney, Nova Scotia, Canada. The spatial maps were designed to create exposure cohorts to help understand the observed increase in health effects. To assess whether contamination can be a proxy for exposures, the following hypothesis was tested: residential soils were impacted by the coke oven and steel plant industrial complex. The spatial map showed contaminants are centered on the industrial facility, significantly correlated, and exceed Canadian health risk-based soil quality guidelines. Core samples taken at 5-cm intervals suggest a consistent deposition over time. The concentrations in Sydney significantly exceed background Sydney soil concentrations, and are significantly elevated compared with North Sydney, an adjacent industrial community. The contaminant spatial maps will also be useful for developing cohorts of exposure and guiding risk management decisions.

Different types of stainless steel used in equipment in meat plants do not affect the initial microbial transfer, including pathogens, from pork skin.

PubMed

Larivière-Gauthier, Guillaume; Quessy, Sylvain; Fournaise, Sylvain; Letellier, Ann; Fravalo, Philippe

2015-07-01

This study describes and measures the impact of different compositions and finishes of stainless steel used in equipment in the meat industry on the transfer of natural flora and selected pathogens from artificially contaminated pork skin. It is known that the adhesion to surfaces of Listeria monocytogenes and Salmonella, 2 pathogens frequently found in contaminated pork meat, depends on the nature and roughness of the surface. Our results show no statistically significant differences in microbial transfer regardless of the types of stainless steel considered, with the highest measured transfer difference being 0.18 log colony-forming units (CFUs)/800 cm(2). Moreover, no differences in total microbial community were observed after transfer on the 5 types of stainless steel using single-strand conformation polymorphism (SSCP). It was concluded that the different characteristics of the stainless steel tested did not affect the initial bacterial transfer in this study.

High temperature oxidation behavior of ODS steels

NASA Astrophysics Data System (ADS)

Kaito, T.; Narita, T.; Ukai, S.; Matsuda, Y.

2004-08-01

Oxide dispersion strengthened (ODS) steels are being developing for application as advanced fast reactor cladding and fusion blanket materials, in order to allow increased operation temperature. Oxidation testing of ODS steel was conducted under a controlled dry air atmosphere to evaluate the high temperature oxidation behavior. This showed that 9Cr-ODS martensitic steels and 12Cr-ODS ferritic steels have superior high temperature oxidation resistance compared to 11 mass% Cr PNC-FMS and 17 mass% Cr ferritic stainless steel. This high temperature resistance is attributed to earlier formation of the protective α-Cr 2O 3 on the outer surface of ODS steels.

Mechanical Properties and Microstructure of Dissimilar Friction Stir Welds of 11Cr-Ferritic/Martensitic Steel to 316 Stainless Steel

NASA Astrophysics Data System (ADS)

Sato, Yutaka S.; Kokawa, Hiroyuki; Fujii, Hiromichi T.; Yano, Yasuhide; Sekio, Yoshihiro

2015-12-01

Dissimilar joints between ferritic and austenitic steels are of interest for selected applications in next generation fast reactors. In this study, dissimilar friction-stir welding of an 11 pct Cr ferritic/martensitic steel to a 316 austenitic stainless steel was attempted and the mechanical properties and microstructure of the resulting welds were examined. Friction-stir welding produces a stir zone without macroscopic weld-defects, but the two dissimilar steels are not intermixed. The two dissimilar steels are interleaved along a sharp zigzagging interface in the stir zone. During small-sized tensile testing of the stir zone, this sharp interface did not act as a fracture site. Furthermore, the microstructure of the stir zone was refined in both the ferritic/martensitic steel and the 316 stainless steel resulting in improved mechanical properties over the adjacent base material regions. This study demonstrates that friction-stir welding can produce welds between dissimilar steels that contain no macroscopic weld-defects and display suitable mechanical properties.

Application of positron annihilation lineshape analysis to fatigue damage and thermal embrittlement for nuclear plant materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uchida, M.; Ohta, Y.; Nakamura, N.

1995-08-01

Positron annihilation (PA) lineshape analysis is sensitive to detect microstructural defects such as vacancies and dislocations. The authors are developing a portable system and applying this technique to nuclear power plant material evaluations; fatigue damage in type 316 stainless steel and SA508 low alloy steel, and thermal embrittlement in duplex stainless steel. The PA technique was found to be sensitive in the early fatigue life (up to 10%), but showed a little sensitivity for later stages of the fatigue life in both type 316 stainless steel and SA508 ferritic steel. Type 316 steel showed a higher PA sensitivity than SA508more » since the initial SA508 microstructure already contained a high dislocation density in the as-received state. The PA parameter increased as a fraction of aging time in CF8M samples aged at 350 C and 400 C, but didn`t change much in CF8 samples.« less

22. ORE STORAGE BRIDGE AT PLANT'S LOWER DOCK, LOOKING SOUTH. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. ORE STORAGE BRIDGE AT PLANT'S LOWER DOCK, LOOKING SOUTH. THE WELLMAN ORE BRIDGE (THERE ARE TWO AT THIS DOCK) WERE ERECTED IN 1908 BY THE CORRIGAN, McKINNEY COMPANY. - Corrigan, McKinney Steel Company, 3100 East Forty-fifth Street, Cleveland, Cuyahoga County, OH

Occupational Profiles in the European Steel Industry.

ERIC Educational Resources Information Center

Franz, Hans-Werner; And Others

The steel industry in Europe has faced great changes, with resulting layoffs and restructuring. Now that the most basic changes seem to be over, it has become evident that the remaining steel industry requires more highly trained workers than was the case previously. Although steel maintenance employees were always highly skilled, steel production…

Gas-fired power in the UK: Bridging supply gaps and implications of domestic shale gas exploitation for UK climate change targets.

PubMed

Turk, Jeremy K; Reay, David S; Haszeldine, R Stuart

2018-03-01

There is a projected shortcoming in the fourth carbon budget of 7.5%. This shortfall may be increased if the UK pursues a domestic shale gas industry to offset projected decreases in traditional gas supply. Here we estimate that, if the project domestic gas supply gap for power generation were to be met by UK shale gas with low fugitive emissions (0.08%), an additional 20.4MtCO 2 e 1 would need to be accommodated during carbon budget periods 3-6. We find that a modest fugitive emissions rate (1%) for UK shale gas would increase global emissions compared to importing an equal quantity of Qatari liquefied natural gas. Additionally, we estimate that natural gas electricity generation would emit 420-466MtCO 2 e (460 central estimate) during the same time period within the traded EU emissions cap. We conclude that domestic shale gas production with even a modest 1% fugitive emissions rate would risk exceedance of UK carbon budgets. We also highlight that, under the current production-based greenhouse gas accounting system, the UK is incentivized to import natural gas rather than produce it domestically. Copyright © 2017 Elsevier B.V. All rights reserved.

Population Development of Tuta absoluta (Meyrick) (Lepidoptera: Gelechiidae) under Simulated UK Glasshouse Conditions

PubMed Central

Cuthbertson, Andrew G.S.; Mathers, James J.; Blackburn, Lisa F.; Korycinska, Anastasia; Luo, Weiqi; Jacobson, Robert J.; Northing, Phil

2013-01-01

Tomato leafminer Tuta absoluta (Meyrick) is a major pest of tomato plants in South America. It was first recorded in the UK in 2009 where it has been subjected to eradication policies. The current work outlines T. absoluta development under various UK glasshouse temperatures. The optimum temperature for Tuta development ranged from 19–23 °C. At 19 °C, there was 52% survival of T. absoluta from egg to adult. As temperature increased (23 °C and above) development time of the moth would appear to decrease. Population development ceases between 7 and 10 °C. Only 17% of eggs hatched at 10 °C but no larvae developed through to adult moths. No eggs hatched when maintained at 7 °C. Under laboratory conditions the total lifespan of the moth was longest (72 days) at 13 °C and shortest (35 days) at both 23 and 25 °C. Development from egg to adult took 58 days at 13 °C; 37 days at 19 °C and 23 days at 25 °C. High mortality of larvae occurred under all temperatures tested. First instar larvae were exposed on the leaf surface for approximately 82 minutes before fully tunnelling into the leaf. Adult longevity was longest at 10 °C with moths living for 40 days and shortest at 19 °C where they survived for 16 days. Generally more males than females were produced. The potential of Tuta absoluta to establish populations within UK protected horticulture is discussed. PMID:26464384

Motivation Types and Mental Health of UK Hospitality Workers.

PubMed

Kotera, Yasuhiro; Adhikari, Prateek; Van Gordon, William

2018-01-01

The primary purposes of this study were to (i) assess levels of different types of work motivation in a sample of UK hospitality workers and make a cross-cultural comparison with Chinese counterparts and (ii) identify how work motivation and shame-based attitudes towards mental health explain the variance in mental health problems in UK hospitality workers. One hundred three UK hospitality workers completed self-report measures, and correlation and multiple regression analyses were conducted to identify significant relationships. Findings demonstrate that internal and external motivation levels were higher in UK versus Chinese hospitality workers. Furthermore, external motivation was more significantly associated with shame and mental health problems compared to internal motivation. Motivation accounted for 34-50% of mental health problems. This is the first study to explore the relationship between motivation, shame, and mental health in UK hospitality workers. Findings suggest that augmenting internal motivation may be a novel means of addressing mental health problems in this worker population.

The development of regulatory expectations for computer-based safety systems for the UK nuclear programme

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hughes, P. J.; Westwood, R.N; Mark, R. T.

2006-07-01

The Nuclear Installations Inspectorate (NII) of the UK's Health and Safety Executive (HSE) has completed a review of their Safety Assessment Principles (SAPs) for Nuclear Installations recently. During the period of the SAPs review in 2004-2005 the designers of future UK naval reactor plant were optioneering the control and protection systems that might be implemented. Because there was insufficient regulatory guidance available in the naval sector to support this activity the Defence Nuclear Safety Regulator (DNSR) invited the NII to collaborate with the production of a guidance document that provides clarity of regulatory expectations for the production of safety casesmore » for computer based safety systems. A key part of producing regulatory expectations was identifying the relevant extant standards and sector guidance that reflect good practice. The three principal sources of such good practice were: IAEA Safety Guide NS-G-1.1 (Software for Computer Based Systems Important to Safety in Nuclear Power Plants), European Commission consensus document (Common Position of European Nuclear Regulators for the Licensing of Safety Critical Software for Nuclear Reactors) and IEC nuclear sector standards such as IEC60880. A common understanding has been achieved between the NII and DNSR and regulatory guidance developed which will be used by both NII and DNSR in the assessment of computer-based safety systems and in the further development of more detailed joint technical assessment guidance for both regulatory organisations. (authors)« less

[Characteristic of Mercury Emissions and Mass Balance of the Typical Iron and Steel Industry].

PubMed

Zhang, Ya-hui; Zhang, Cheng; Wang, Ding-yong; Luo, Cheng-zhong; Yang, Xi; Xu, Feng

2015-12-01

To preliminarily discuss the mercury emission characteristics and its mass balance in each process of the iron and steel production, a typical iron and steel enterprise was chosen to study the total mercury in all employed materials and estimate the input and output of mercury during the steel production process. The results showed that the mercury concentrations of input materials in each technology ranged 2.93-159.11 µg · kg⁻¹ with the highest level observed in ore used in blast furnace, followed by coal of sintering and blast furnace. The mercury concentrations of output materials ranged 3.09-18.13 µg · kg⁻¹ and the mercury concentration of dust was the highest, followed by converter slag. The mercury input and the output in the coking plant were 1346.74 g · d⁻¹ ± 36.95 g · d⁻¹ and 177.42 g · d⁻¹ ± 13.73 g · d⁻¹, respectively. In coking process, mercury mainly came from the burning of coking coal. The sintering process was the biggest contributor for mercury input during the iron and steel production with the mercury input of 1075. 27 g · d⁻¹ ± 60.89 g · d⁻¹ accounting for 68.06% of the total mercury input during this production process, and the ore powder was considered as the main mercury source. For the solid output material, the output in the sintering process was 14.15 g · d⁻¹ ± 0.38 g · d⁻¹, accounting for 22.61% of the total solid output. The mercury emission amount from this studied iron and steel enterprise was estimated to be 553.83 kg in 2013 with the emission factor of 0.092 g · t⁻¹ steel production. Thus, to control the mercury emissions, iron and steel enterprises should combine with production practice, further reduce energy consumption of coking and sintering, or improve the quality of raw materials and reduce the input of mercury.

Globalisation of Researcher Mobility within the UK Higher Education: Explaining the Presence of Overseas Academics in the UK Academia

ERIC Educational Resources Information Center

Khattab, Nabil; Fenton, Steve

2016-01-01

In this paper, we argue that the power structure that lies within the UK elite universities dictates a division of labour through which the inflows of overseas academics into the UK academic labour markets are skewed towards these elite academic institutions where they are employed primarily in research-only posts. These posts, are less valued and…

Characterization of friction stir welded joint of low nickel austenitic stainless steel and modified ferritic stainless steel

NASA Astrophysics Data System (ADS)

Mondal, Mounarik; Das, Hrishikesh; Ahn, Eun Yeong; Hong, Sung Tae; Kim, Moon-Jo; Han, Heung Nam; Pal, Tapan Kumar

2017-09-01

Friction stir welding (FSW) of dissimilar stainless steels, low nickel austenitic stainless steel and 409M ferritic stainless steel, is experimentally investigated. Process responses during FSW and the microstructures of the resultant dissimilar joints are evaluated. Material flow in the stir zone is investigated in detail by elemental mapping. Elemental mapping of the dissimilar joints clearly indicates that the material flow pattern during FSW depends on the process parameter combination. Dynamic recrystallization and recovery are also observed in the dissimilar joints. Among the two different stainless steels selected in the present study, the ferritic stainless steels shows more severe dynamic recrystallization, resulting in a very fine microstructure, probably due to the higher stacking fault energy.

Solar wind modulation of UK lightning

NASA Astrophysics Data System (ADS)

Davis, Chris; Harrison, Giles; Lockwood, Mike; Owens, Mathew; Barnard, Luke

2013-04-01

The response of lightning rates in the UK to arrival of high speed solar wind streams at Earth is investigated using a superposed epoch analysis. The fast solar wind streams' arrivals are determined from modulation of the solar wind Vy component, measured by the Advanced Composition Explorer (ACE) spacecraft. Lightning rate changes around these event times are then determined from the very low frequency Arrival Time Difference (ATD) system of the UK Met Office. Arrival of high speed streams at Earth is found to be preceded by a decrease in total solar irradiance and an increase in sunspot number and Mg II emissions. These are consistent with the high speed stream's source being co-located with an active region appearing on the Eastern solar limb and rotating at the 27 day rate of the Sun. Arrival of the high speed stream at Earth also coincides with a rapid decrease in cosmic ray flux and an increase in lightning rates over the UK, persisting for around 40 days. The lightning rate increase is corroborated by an increase in the total number of thunder days observed by UK Met stations, again for around 40 days after the arrival of a high speed solar wind stream. This increase in lightning may be beneficial to medium range forecasting of hazardous weather.

Nickel-free austenitic stainless steels for medical applications.

PubMed

Yang, Ke; Ren, Yibin

2010-02-01

The adverse effects of nickel ions being released into the human body have prompted the development of high-nitrogen nickel-free austenitic stainless steels for medical applications. Nitrogen not only replaces nickel for austenitic structure stability but also much improves steel properties. Here we review the harmful effects associated with nickel in medical stainless steels, the advantages of nitrogen in stainless steels, and emphatically, the development of high-nitrogen nickel-free stainless steels for medical applications. By combining the benefits of stable austenitic structure, high strength and good plasticity, better corrosion and wear resistances, and superior biocompatibility compared to the currently used 316L stainless steel, the newly developed high-nitrogen nickel-free stainless steel is a reliable substitute for the conventional medical stainless steels.

Nickel-free austenitic stainless steels for medical applications

PubMed Central

Yang, Ke; Ren, Yibin

2010-01-01

The adverse effects of nickel ions being released into the human body have prompted the development of high-nitrogen nickel-free austenitic stainless steels for medical applications. Nitrogen not only replaces nickel for austenitic structure stability but also much improves steel properties. Here we review the harmful effects associated with nickel in medical stainless steels, the advantages of nitrogen in stainless steels, and emphatically, the development of high-nitrogen nickel-free stainless steels for medical applications. By combining the benefits of stable austenitic structure, high strength and good plasticity, better corrosion and wear resistances, and superior biocompatibility compared to the currently used 316L stainless steel, the newly developed high-nitrogen nickel-free stainless steel is a reliable substitute for the conventional medical stainless steels. PMID:27877320

Effect of Spreading Time on Contact Angle of Nanofluid on the Surface of Stainless Steel AISI 316 and Zircalloy 4

NASA Astrophysics Data System (ADS)

Prajitno, D. H.; Trisnawan, V.; Syarif, D. G.

2017-05-01

The solid surface tension plays an important role in the heat and mass transfer system for heat exchanger equipment. In the nuclear power plant industry, the stainless steel AISI 316 and Zircalloy 4 have been used for long time as structure materials. The purpose of the experimental is to study solid state surface tension behavior by measure contact angle Nano fluid contain nano particle alumina on metal surface of stainless steel AISI 316 and Zircalloy 4 by sessile drop method. The experiment is to measure the static contact angle and drop nano fluid contains nano particle alumina on stainless steel 316 and zircalloy 4 with different spreading time from 1 to 30 minute. It was observed that stainless steel 316 and zircalloy 4 lose their hydrophobic properties with increasing elapsed time during drop of nano fluid on the surface of alloy. As a result the contact angle of nano fluid on surface of metal is decrease with increasing elapsed time. While the magnitude diameter of drop nano fluid and wetting surface is increase with increasing elapsed time on the surface of the stainless steel SS 316 and Zircalloy 4.

Food advertising during children's television in Canada and the UK.

PubMed

Adams, J; Hennessy-Priest, K; Ingimarsdóttir, S; Sheeshka, J; Ostbye, T; White, M

2009-09-01

Television advertisements for less healthy foods are thought to contribute to overweight and obesity in children. In the UK, new regulations on television food advertising to children came into effect in April 2007. These prohibit advertisements for "less healthy" foods during or around programmes "of particular appeal to" (OPAT) children. In Canada, self-regulated codes of practice on television food advertising to children were recently strengthened. To document the nutritional content of food advertised and number of advertisements OPAT children broadcast in the UK and central Canada before the introduction of the new UK regulations. All food advertisements broadcast on four popular channels in Canada and the three terrestrial commercial channels in the UK during 1 week in 2006 were identified and linked to relevant nutritional data. Food advertisements OPAT children and for "less healthy" products were identified using the criteria in the UK regulations. 2315 food related advertisements broadcast in Canada and 1365 broadcast in the UK were included. 52-61% were for "less healthy" products; 5-11% were OPAT children. Around 5% of food advertisements would have been prohibited under the new UK regulations. There were few differences in the nutritional content of food described in advertisements that were and were not OPAT children. There was little evidence that food described in advertisements OPAT children were any less healthy than those that were not. Few food advertisements are likely to be prohibited by the new UK regulations.

UK Renal Registry 16th annual report: chapter 9 adequacy of haemodialysis in UK adult patients in 2012: national and centre-specific analyses.

PubMed

Shaw, Catriona; Steenkamp, Retha; Davenport, Andrew

2013-01-01

Outcomes in patients treated with haemodialysis (HD) are influenced by the delivered dose of dialysis. The UK Renal Association (RA) publishes clinical practice guidelines which include recommendations for dialysis dose. The urea reduction ratio (URR) is a widely used measure of dialysis dose and has historically been the measure of adequacy reported by the UKRR. This chapter aims to determine the extent to which patients achieved the recommended UK target. All 71 UK renal centres submitted data to the UK Renal Registry (UKRR). Two groups of patients were included in the analyses: the prevalent HD patient population on 30st September 2012 and the incident HD patient population for 2011. Centres returning data on <50% of their patient population or centres with <20 patients were excluded from centrespecific comparisons. Data regarding URR were available from 63 renal centres in the UK. Forty nine centres provided URR data on more than 90% of prevalent HD patients. The proportion of patients in the UK who met the UK clinical practice guideline for URR (>65%) increased from 69% in 2000 to 88% in 2012. There was persistent variation observed between centres, with 21 centres attaining the RA clinical practice guideline in >90% of patients, 38 centres attaining the guideline in 70-90% of patients and one centre in less than 70% of patients. The overall proportion of prevalent HD patients with a URR >65% has continued to improve over time. The delivered dose of HD, as measured by URR for patients with established renal failure, has increased over the last decade. Whilst the majority of UK patients achieved the target URR there was considerable variation between centres in the percentage of patients achieving the current guideline. © 2014 S. Karger AG, Basel.

Nutritional Knowledge of UK Coaches

PubMed Central

Cockburn, Emma; Fortune, Alistair; Briggs, Marc; Rumbold, Penny

2014-01-01

Athletes obtain nutritional information from their coaches, yet their competency in this area is lacking. Currently, no research exists in the UK which has a different coach education system to many other countries. Therefore, the aim of this study was to evaluate the sports nutrition knowledge of UK coaching certificate (UKCC) level 2 and 3, hockey and netball qualified coaches. All coaches (n = 163) completed a sports nutrition questionnaire to identify: (a) if they provided nutritional advice; (b) their level of sport nutrition knowledge; and (c) factors that may have contributed to their level of knowledge. Over half the coaches provided advice to their athletes (n = 93, 57.1%), even though they were not competent to do so. Coaches responded correctly to 60.3 ± 10.5% of all knowledge questions with no differences between those providing advice and those who did not (p > 0.05). Those coaches who had undertaken formal nutrition training achieved higher scores than those who had not (p < 0.05). In conclusion, UK sports coaches would benefit from continued professional development in sports nutrition to enhance their coaching practice. PMID:24727434

Aerosol filtration with steel fiber filters

NASA Astrophysics Data System (ADS)

Bergman, W.; Wilson, K.; Larsen, G.; Lopez, R.

1993-04-01

An experimental study has been conducted of aerosol penetration through a new high efficiency steel fiber filter and filter media that was developed in cooperation with Pall Corporation. Previous studies have shown that sintered steel fiber media have significant improvements in higher filter efficiency and lower pressure drop than the previous steel filter technology based on sintered powder metal media. In the present study, measurements were made of the penetration of dioctyl sebacate (DOS) aerosols through flat sheet samples, pleated cartridge filters, and a 1000 cfm filter having 64 cartridges housed in a 2 x 2 x 1 ft. frame. The steel fiber media used in our study consists of 2 micron diameter stainless steel (316 L) fibers sintered together into sheets.

Design of Fully Austenitic Medium Manganese Steels

NASA Astrophysics Data System (ADS)

Luan, G.; Volkova, O.; Mola, J.

2018-06-01

Due to their higher ferrite potential compared to high Mn twinning-induced plasticity (TWIP) steels, medium Mn steels usually exhibit austenitic-ferritic microstructures, which makes them suitable for third-generation advanced high-strength steel applications. Nevertheless, the strain hardening characteristics of medium Mn steels are inferior to those of fully austenitic high Mn steels. The present work introduces alloy design strategies to obtain fully austenitic medium Mn steels capable of the TWIP effect. To achieve a fully austenitic microstructure, the martensite start temperature is reduced by raising the C concentration to above 1 mass-%, which in turn facilitates the formation of cementite. The formation of cementite during cooling from austenitization temperature is counteracted by alloying with Al. Microstructural examination of slowly-cooled Fe‑Mn‑Al‑C and Fe‑Mn‑C steels indicated that Al changes the morphology of intergranular cementite from plate-shaped to equiaxed.

Incorporation of organic tritium (3H) by marine organisms and sediment in the severn estuary/Bristol channel (UK).

PubMed

McCubbin, D; Leonard, K S; Bailey, T A; Williams, J; Tossell, P

2001-10-01

Discharges of tritium (3H) into the Severn estuary/Bristol Channel (UK) arise from the authorized release of wastes from nuclear power plants at Hinkley Point and Berkley/Oldbury and from the Nycomed-Amersham radiochemical plant, via the sewer system, at Cardiff. The wastes from the nuclear power plants probably consist almost entirely of 3H2O, whereas those from the radiochemical plant also include uncharacterized 3H labelled organic compounds. The total 3H concentrations in demersal fish and other benthic organisms in the vicinity of the Cardiff Eastern sewer outfall are significantly elevated compared to those observed around other UK nuclear establishments. Concentrations in filtered seawater were approximately 10 Bq kg(-1) whilst levels in surface sediment, seaweed (Fucus vesiculosis) and mussels (Mytilus edulis)/flounder (Platichthys flesus) were in the order of 6 x 10(2), 2 x 10(3), and 10(5) Bq kg(-1) (dry weight), respectively. Almost all the 3H found in sediment and biota were organically bound tritium (OBT). The high concentration in these materials, relative to that in seawater, is due to the presence of bioavailable organic 3H labelled compounds in the radiochemical waste. It is suggested that bioaccumulation of 3H by benthic organisms and demersal fish occurs primarily via a pathway of physico-chemical sorption/bacterial transformation of dissolved 3H labelled organic compounds into particulate organic matter, and subsequent transfer up a web of sediment dwelling microbes and meiofauna. Variations in 3H accumulation between individual organisms have been interpreted in terms of their different feeding behaviour. Relatively low concentrations were observed in the herbivorous winkle (Littorina littorea) and the pelagic Sprat (Spratus spratus) compared with other benthic organisms and demersal fish. The elevated 3H concentrations in seafood, due to bioaccumulation of OBT, have low radiological significance even for the local critical group of seafood

13. View northeast of boiler plant (Building 39), engineering work ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. View northeast of boiler plant (Building 39), engineering work order building/former tin shop (Building 129), laundry MAT workshop (Building 28), pipe shop/former water softening plant (Building 81), paint spray shop/former blacksmith shop (Building 95), fuel oil storage tank building (Building 103), mason's shop (Building 77), and carpenter shop (Building 97) with steel water tank (Building 124) in background - National Home for Disabled Volunteer Soldiers Western Branch, 4101 South Fourth Street, Leavenworth, Leavenworth County, KS

On the Constitutive Model of Nitrogen-Containing Austenitic Stainless Steel 316LN at Elevated Temperature

PubMed Central

Zhang, Lei; Feng, Xiao; Wang, Xin; Liu, Changyong

2014-01-01

The nitrogen-containing austenitic stainless steel 316LN has been chosen as the material for nuclear main-pipe, which is one of the key parts in 3rd generation nuclear power plants. In this research, a constitutive model of nitrogen-containing austenitic stainless steel is developed. The true stress-true strain curves obtained from isothermal hot compression tests over a wide range of temperatures (900–1250°C) and strain rates (10−3–10 s−1), were employed to study the dynamic deformational behavior of and recrystallization in 316LN steels. The constitutive model is developed through multiple linear regressions performed on the experimental data and based on an Arrhenius-type equation and Zener-Hollomon theory. The influence of strain was incorporated in the developed constitutive equation by considering the effect of strain on the various material constants. The reliability and accuracy of the model is verified through the comparison of predicted flow stress curves and experimental curves. Possible reasons for deviation are also discussed based on the characteristics of modeling process. PMID:25375345

46 CFR 56.60-5 - Steel (High temperature applications).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel, and...

46 CFR 56.60-5 - Steel (High temperature applications).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel, and...

46 CFR 56.60-5 - Steel (High temperature applications).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel, and...

46 CFR 56.60-5 - Steel (High temperature applications).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel, and...

46 CFR 56.60-5 - Steel (High temperature applications).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel, and...

Updated atmospheric speciated mercury emissions from iron and steel production in China during 2000-2015

NASA Astrophysics Data System (ADS)

Wu, Qingru; Gao, Wei; Wang, Shuxiao; Hao, Jiming

2017-09-01

Iron and steel production (ISP) is one of the significant atmospheric Hg emission sources in China. Atmospheric mercury (Hg) emissions from ISP during 2000-2015 were estimated by using a technology-based emission factor method. To support the application of this method, databases of Hg concentrations in raw materials, technology development trends, and Hg removal efficiencies of air pollution control devices (APCDs) were constructed through national sampling and literature review. Hg input to ISP increased from 21.6 t in 2000 to 94.5 t in 2015. In the various types of raw materials, coking coal and iron concentrates contributed 35-46 and 25-32 % of the total Hg input. Atmospheric Hg emissions from ISP increased from 11.5 t in 2000 to 32.7 t in 2015 with a peak of 35.6 t in 2013. Pollution control promoted the increase in average Hg removal efficiency, from 47 % in 2000 to 65 % in 2015. During the study period, sinter/pellet plants and blast furnaces were the largest two emission processes. However, emissions from roasting plants and coke ovens cannot be ignored, which accounted for 22-34 % of ISP's emissions. Overall, Hg speciation shifted from 50/44/6 (gaseous elemental Hg (Hg0)/gaseous oxidized Hg (HgII)/particulate-bound Hg (Hgp)) in 2000 to 40/59/1 in 2015, which indicated a higher proportion of Hg deposition around the emission points. Future emissions of ISP were expected to decrease based on the comprehensive consideration crude-steel production, steel scrap utilization, energy saving, and pollution control measures.

Marine Atmospheric Corrosion of Carbon Steel: A Review.

PubMed

Alcántara, Jenifer; Fuente, Daniel de la; Chico, Belén; Simancas, Joaquín; Díaz, Iván; Morcillo, Manuel

2017-04-13

The atmospheric corrosion of carbon steel is an extensive topic that has been studied over the years by many researchers. However, until relatively recently, surprisingly little attention has been paid to the action of marine chlorides. Corrosion in coastal regions is a particularly relevant issue due the latter's great importance to human society. About half of the world's population lives in coastal regions and the industrialisation of developing countries tends to concentrate production plants close to the sea. Until the start of the 21st century, research on the basic mechanisms of rust formation in Cl - -rich atmospheres was limited to just a small number of studies. However, in recent years, scientific understanding of marine atmospheric corrosion has advanced greatly, and in the authors' opinion a sufficient body of knowledge has been built up in published scientific papers to warrant an up-to-date review of the current state-of-the-art and to assess what issues still need to be addressed. That is the purpose of the present review. After a preliminary section devoted to basic concepts on atmospheric corrosion, the marine atmosphere, and experimentation on marine atmospheric corrosion, the paper addresses key aspects such as the most significant corrosion products, the characteristics of the rust layers formed, and the mechanisms of steel corrosion in marine atmospheres. Special attention is then paid to important matters such as coastal-industrial atmospheres and long-term behaviour of carbon steel exposed to marine atmospheres. The work ends with a section dedicated to issues pending, noting a series of questions in relation with which greater research efforts would seem to be necessary.

Marine Atmospheric Corrosion of Carbon Steel: A Review

PubMed Central

Alcántara, Jenifer; de la Fuente, Daniel; Chico, Belén; Simancas, Joaquín; Díaz, Iván; Morcillo, Manuel

2017-01-01

The atmospheric corrosion of carbon steel is an extensive topic that has been studied over the years by many researchers. However, until relatively recently, surprisingly little attention has been paid to the action of marine chlorides. Corrosion in coastal regions is a particularly relevant issue due the latter’s great importance to human society. About half of the world’s population lives in coastal regions and the industrialisation of developing countries tends to concentrate production plants close to the sea. Until the start of the 21st century, research on the basic mechanisms of rust formation in Cl−-rich atmospheres was limited to just a small number of studies. However, in recent years, scientific understanding of marine atmospheric corrosion has advanced greatly, and in the authors’ opinion a sufficient body of knowledge has been built up in published scientific papers to warrant an up-to-date review of the current state-of-the-art and to assess what issues still need to be addressed. That is the purpose of the present review. After a preliminary section devoted to basic concepts on atmospheric corrosion, the marine atmosphere, and experimentation on marine atmospheric corrosion, the paper addresses key aspects such as the most significant corrosion products, the characteristics of the rust layers formed, and the mechanisms of steel corrosion in marine atmospheres. Special attention is then paid to important matters such as coastal-industrial atmospheres and long-term behaviour of carbon steel exposed to marine atmospheres. The work ends with a section dedicated to issues pending, noting a series of questions in relation with which greater research efforts would seem to be necessary. PMID:28772766

Assisted dying - should the UK change its stance?

PubMed

Gordon, Daniel; Raphael, Claire E; Vassiliou, Vassilios

2015-04-01

Along with an increasing interest in assisted dying by many European and North American countries, some of which have already modified their existing laws to accommodate this, the interest in assisted dying in the UK has increased once again following Lord Falconer's Assisted Dying for the Terminally Ill Bill. Drawing on examples from countries where similar assisted dying laws are already in place, this article analyses and contextualises the proposed bill and discusses its potential pitfalls and benefits for the UK. © The European Society of Cardiology 2015 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Questions raised over future of UK research council

NASA Astrophysics Data System (ADS)

Banks, Michael

2010-02-01

Five senior physicists have written to the UK science minister, Lord Drayson, about the "dismal future" for researchers in the country in the wake of a £40m shortfall in the budget of the Science and Technology Facilities Council (STFC). The physicists, who chair the STFC's five advisory panels, have also called for structural reforms to be made to the council. They warn that unless the government takes action to reverse the situation, the UK will be "perceived as an untrustworthy partner in global projects" and predict that a brain drain of the best UK scientists to positions overseas will ensue.

OBLIQUE/EXTERIOR VIEW, LOOKING NORTHEAST, WITH SINTERING PLANT RUINS AND TRACES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OBLIQUE/EXTERIOR VIEW, LOOKING NORTHEAST, WITH SINTERING PLANT RUINS AND TRACES OF L. & N. RAILROAD EXTENDING THROUGH GRACE'S GAP TOWARD THE BIRMINGHAM CITY CENTER. - Republic Steel, Spaulding Red Ore Mine (Ruins), Spanning Grace's Pass at Louisville & Nashville Railroad, Birmingham, Jefferson County, AL

The Attainment of Ethnic Minority Students in UK Higher Education

ERIC Educational Resources Information Center

Richardson, John T. E.

2008-01-01

Recent studies have suggested that academic attainment by ethnic minority graduates at UK institutions of higher education is lower than that by White graduates. This was confirmed using a database of all UK-domiciled graduates from UK higher education institutions in 2004-05. The trend was greater in older students than in younger students, in…

Molten salt thermal energy storage subsystem for solar thermal central receiver plants

NASA Astrophysics Data System (ADS)

Wells, P. B.; Nassopoulos, G. P.

1982-02-01

The development of a low cost thermal energy storage subsystem for large solar plants is described. Molten nitrate salt is used as both the solar plant working fluid and the storage medium. The storage system consists of a specially designed hot tank to hold salt at a storage temperature of 839K (1050 deg F) and a separate carbon steel cold tank to hold the salt after its thermal energy has been extracted to generate steam. The hot tank is lined with insulating firebrick to reduce the shell temperature to 561K (550 deg F) so that a low cost carbon steel shell is used. The internal insulation is protected from the hot salt by a unique metal liner with orthogonal corrugations to allow for numerous cycles of thermal expansion and contraction. A preliminary design for a large commercial size plant (1200 MWh sub +), a laboratory test program for the critical components, and the design, construction, and test of a small scale (7 MWH sub t) research experiment at the Central Receiver Test Facility in Albuquerque, New Mexico is described.

Development of high purity large forgings for nuclear power plants

NASA Astrophysics Data System (ADS)

Tanaka, Yasuhiko; Sato, Ikuo

2011-10-01

The recent increase in the size of energy plants has been supported by the development of manufacturing technology for high purity large forgings for the key components of the plant. To assure the reliability and performance of the large forgings, refining technology to make high purity steels, casting technology for gigantic ingots, forging technology to homogenize the material and consolidate porosity are essential, together with the required heat treatment and machining technologies. To meet these needs, the double degassing method to reduce impurities, multi-pouring methods to cast the gigantic ingots, vacuum carbon deoxidization, the warm forging process and related technologies have been developed and further improved. Furthermore, melting facilities including vacuum induction melting and electro slag re-melting furnaces have been installed. By using these technologies and equipment, large forgings have been manufactured and shipped to customers. These technologies have also been applied to the manufacture of austenitic steel vessel components of the fast breeder reactors and components for fusion experiments.

A Comparative Study on Formability of the Third-Generation Automotive Medium-Mn Steel and 22MnB5 Steel

NASA Astrophysics Data System (ADS)

Zheng, Guojun; Li, Xiaodong; Chang, Ying; Wang, Cunyu; Dong, Han

2018-02-01

Third-generation advanced automotive medium-Mn steel, which can replace 22MnB5 steel, was newly developed to improve the lightweight and crashworthiness of automobile. Studies on the formability and simulation method of medium-Mn steel have just been initiated. In this study, finite element simulation models of square-cup deep drawing were established based on various material property experiments and validated by experiments. The effects of blank holder force (BHF), fillet radii of tools (die and punch) on the maximum drawing depth (MDD), thickness distribution of the formed products, and the microstructure before and after forming were investigated and compared with those on 22MnB5 steel. Results show that the MDD of the two steels decreased with increased BHF but increased with the fillet radius of punch; however, the fillet radius of die showed no significant effect on the MDD for both steels. Compared with hot-formed 22MnB5 steel, the martensitic transformation of the hot-formed medium-Mn steel is rarely influenced by the process parameters; thus, it holds the complete, fine-grained, and uniform martensitic microstructure. Moreover, the medium-Mn has better formability, lower initial blank temperature, and smaller impact of BHF and fillet radius of tools on the hot-formed product. Thus, a theoretical basis for the replacement of 22MnB5 steel by medium-Mn steel in hot forming process is provided.

Measurement of Outgassing Rates of Steels.

PubMed

Park, Chongdo; Kim, Se-Hyun; Ki, Sanghoon; Ha, Taekyun; Cho, Boklae

2016-12-13

Steels are commonly used materials in the fabrication of vacuum systems because of their good mechanical, corrosion, and vacuum properties. A variety of steels meet the criterion of low outgassing required for high or ultrahigh vacuum applications. However, a given material can present different outgassing rates depending on its manufacturing process or the various pretreatment processes involved during the fabrication. Thus, the measurement of outgassing rates is highly desirable for a specific vacuum application. For this reason, the rate-of-pressure rise (RoR) method is often used to measure the outgassing of hydrogen after bakeout. In this article, a detailed description of the design and execution of the experimental protocol involved in the RoR method is provided. The RoR method uses a spinning rotor gauge to minimize errors that stem from outgassing or the pumping action of a vacuum gauge. The outgassing rates of two ordinary steels (stainless steel and mild steel) were measured. The measurements were made before and after the heat pretreatment of the steels. The heat pretreatment of steels was performed to reduce the outgassing. Extremely low rates of outgassing (on the order of 10 - 11 Pa m 3 sec - 1 m - 2 ) can be routinely measured using relatively small samples.

Hydrogen attack in Cr-Mo steels. [3Cr-1. 5Mo and 2. 25Cr-1Mo steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruoff, S.; Stone, D.; Wanagel, J.

Experiments conducted upon 3Cr-1.5Mo steel at elevated temperatures (600 C), and high pressure hydrogen (2000 psi), have shown a greater resistence to hydrogen attack compared with similar studies of 2.25Cr-lMo steels. Hydrogen exposure tests with and without an applied stress have been performed on both types of steels. Results of similar conditions show clear evidence of hydrogen attack in 2.25Cr-lMo steel, however, for the 3Cr-1.5Mo steel with exposure time up to 80 days without an applied stress no evidence of hydrogen attack is observed. For stress-rupture tests using stresses of 14 and 16 ksi, the 3Cr-1.5Mo steel showed no effectsmore » of hydrogen attack, and no damage was observed using a SEM.« less

Steeling and Resilience in Art Education

ERIC Educational Resources Information Center

Heise, Donalyn

2014-01-01

Steel is an incredibly strong alloy of iron and carbon. Due to its incredible strength and durability, this resilient material is commonly used for constructing buildings. The transitive verb "steeling" is defined in Miriam-Webster dictionary as "to fill with resolution or determination, as in, she 'steeled herself to face the…

Heavy-section steel irradiation program. Semiannual progress report, October 1996--March 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosseel, T.M.

1998-02-01

Maintaining the integrity of the reactor pressure vessel (RPV) in a light-water-cooled nuclear power plant is crucial in preventing and controlling severe accidents that have the potential for major contamination release. Because the RPV is the only key safety-related component of the plant for which a redundant backup system does not exist, it is imperative to fully understand the degree of irradiation-induced degradation of the RPV`s fracture resistance that occurs during service. For this reason, the Heavy-Section Steel Irradiation (HSSI) Program has been established. Its primary goal is to provide a thorough, quantitative assessment of the effects of neutron irradiationmore » on the material behavior and, in particular, the fracture toughness properties of typical pressure-vessel steels as they relate to light-water RPV integrity. Effects of specimen size; material chemistry; product form and microstructure; irradiation fluence, flux, temperature, and spectrum; and postirradiation annealing are being examined on a wide range of fracture properties. The HSSI Program is arranged into eight tasks: (1) program management, (2) irradiation effects in engineering materials, (3) annealing, (4) microstructural analysis of radiation effects, (5) in-service irradiated and aged material evaluations, (6) fracture toughness curve shift method, (7) special technical assistance, and (8) foreign research interactions. The work is performed by the Oak Ridge National Laboratory.« less

Effectiveness of the United Steel Workers of America Coke Oven Intervention Program.

PubMed

Parkinson, D K; Bromet, E J; Dew, M A; Dunn, L O; Barkman, M; Wright, M

1989-05-01

This paper describes the implementation and evaluation of the Coke Oven Intervention Program developed jointly by the United Steel Workers of America and the University of Pittsburgh. The program was offered on four occasions at each of seven coke oven plants over a 2-year period. Participants were compared with nonparticipating co-workers and controls from matched plants on knowledge of the Coke Oven Standard and workplace behaviors. Few baseline differences were found among participants, nonparticipants, and controls. Participants improved significantly as a result of the program, with those attending multiple programs accruing the greatest benefits. Panel controls interviewed on six occasions throughout the 2-year period showed little improvement. Reasons for and implications of the effectiveness of the program are discussed.

[A cohort study on occupational noise induced hearing loss in workers at an iron and steel plant].

PubMed

Yu, S F; Chen, G S; Jiao, J; Gu, G Z; Zhang, H L; Wang, X M; Zhou, W H; Wu, H; Li, Y H; Zheng, Y X

2017-01-06

Objective: To analyze the incidence rate of occupational noise-induced hearing loss in noise-exposed workers in an iron and steel plant from 2006 to 2015. Methods: Using a cohort study method, workers exposed to occupational noise from Jan 1, 2006 to Dec 12, 2015 were followed up and the pure tone hearing test was conducted. In total, 6 297 subjects completed two or more physical checks and the pure tone hearing test and were included in the analysis. The noise exposure level at the workplace and the equivalent continuous A-weighted sound pressure level for workers was monitored and the cumulative noise exposure dose was evaluated. The subjects were divided into low, middle and high exposure groups according to the noise exposure level, and the equivalent continuous A-weighted sound pressure level for 8 hours for each group was 80.6-85.0, 85.1-90.0 and 90.1-103.4 dB (A), respectively. While the RR and 95% CI were derived from unconditional logistic regression models. In logistic regression analysis, confounding factors such as age, gender, smoking habit, drinking habit, high temperature exposure and chemical hazards exposure level were controlled. Results: During the follow-up period, 392 cases of occupational noise-induced hearing loss were diagnosed among the 6 297 subjects, with an incidence rate of 6.23%; 318 cases of high-frequency hearing loss were diagnosed, with an incidence rate of 5.05%; and 74 cases of occupational noise-induced deafness were diagnosed, with an incidence rate of 1.18% . The incidence rates of hearing loss among the high, medium and low exposure groups were 9.22% (158/1 737), 6.49% (204/3 142) and 2.08% (30/1 442), respectively; the rates of high-frequency hearing loss were 7.41% (127/1 737), 5.25% (165/3 142) and 1.80% (26/1 442), respectively; and the rates of occupational noise-induced deafness were 1.81% (31/1 737), 1.24% (39/3 142) and 0.28% (4/1 442), respectively. For the groups corresponding to cumulative noise exposure doses of �

History of UK contribution to astronautics: Politics and government

NASA Astrophysics Data System (ADS)

Hicks CB, Colin

2009-12-01

In all developed countries, once it emerged from the amateur era, Space (and especially rocketry) moved on the public agenda because of its potential significance for both the civil and military policies of governments (coupled with its appetite for new money). In the UK the policy treatment of Space broadly paralleled that in other countries until the post-Empire trauma, the burn-out of the White-Hot Technological revolution of Harold Wilson, and the financial crises of the 1970s exhausted the public appetite for large scale publicly funded projects in high technology. The culmination for Space of these pressures came in 1986-1987 when the UK rejected the emerging international consensus and, almost alone, stayed outside the manned space commitments which developed into the International Space Station. In this paper, Colin Hicks will review the UK political developments which led up to the 1986-1987 decision and how the politics and organisation of UK space activity have developed since then to the point where in 2008 a major government review of the UK involvement in manned space was commissioned.

Simple Heat Treatment for Production of Hot-Dip Galvanized Dual Phase Steel Using Si-Al Steels

NASA Astrophysics Data System (ADS)

Equihua-Guillén, F.; García-Lara, A. M.; Muñíz-Valdes, C. R.; Ortíz-Cuellar, J. C.; Camporredondo-Saucedo, J. E.

2014-01-01

This work presents relevant metallurgical considerations to produce galvanized dual phase steels from low cost aluminum-silicon steels which are produced by continuous strip processing. Two steels with different contents of Si and Al were austenized in the two-phase field ferrite + austenite (α + γ) in a fast manner to obtain dual phase steels, suitable for hot-dip galvanizing process, under typical parameters of continuous annealing processing line. Tensile dual phase properties were obtained from specimens cooled from temperature below Ar3, held during 3 min, intermediate cooling at temperature above Ar1 and quenching in Zn bath at 465 °C. The results have shown typical microstructure and tensile properties of galvanized dual phase steels. Finally, the synergistic effect of aluminum, silicon, and residual chromium on martensite start temperature ( M s), critical cooling rate ( C R), volume fraction of martensite, and tensile properties has been studied.

Corrosion of carbon steels, stainless steels, and titanium in aqueous lithium bromide solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guinon, J.L.; Garcia-Anton, J.; Perez-Herranz, V.

1994-03-01

Effects of lithium bromide (LiBr) concentration, pH, temperature, exposure time, and the action of some inhibitors on corrosion of several carbon (C) steels, stainless steels (SS), and a titanium (Ti) alloy were studied. Corrosion rates were determined by the polarization resistance method and compared to rates determined by weight-loss measurements. Pitting potentials (E[sub p]) were evaluated in neutral LiBr solution and with different inhibitors. Pit density and average pit depth depended on the metal tested, with lowest values for Ti, the next lowest values for type 316 SS (UNS S31600), and the highest values for UNS G41350 tempered steel.

High Fragmentation Steel Production Process

DTIC Science & Technology

1981-08-01

Hsv j , —U -I* : -’ 1 . ’ ; - * - 1 "^Sv i ! :.:.; 1 HEBUCTIOK AHU.,, .../y?.;-’" • jttoireAnoi..|..r!.5^«. ::^;;;i:^l^~!’in...on rmrerae aide 11 neceaaary and Identity by block number) HF- 1 Steel Metallurgical Evaluation MMT-Process improvement 20. ABSTRACT ("ContfBu...ao reraram attba tt n*c*aaMey and. IderUlty by block numbat) Two heats of B0F HF- 1 steel were purchased, one from Republic Steel and one from

Persistence of deposited metals in the lungs after stainless steel and mild steel welding fume inhalation in rats.

PubMed

Antonini, James M; Roberts, Jenny R; Stone, Samuel; Chen, Bean T; Schwegler-Berry, Diane; Chapman, Rebecca; Zeidler-Erdely, Patti C; Andrews, Ronnee N; Frazer, David G

2011-05-01

Welding generates complex metal fumes that vary in composition. The objectives of this study were to compare the persistence of deposited metals and the inflammatory potential of stainless and mild steel welding fumes, the two most common fumes used in US industry. Sprague-Dawley rats were exposed to 40 mg/m(3) of stainless or mild steel welding fumes for 3 h/day for 3 days. Controls were exposed to filtered air. Generated fume was collected, and particle size and elemental composition were determined. Bronchoalveolar lavage was done on days 0, 8, 21, and 42 after the last exposure to assess lung injury/inflammation and to recover lung phagocytes. Non-lavaged lung samples were analyzed for total and specific metal content as a measure of metal persistence. Both welding fumes were similar in particle morphology and size. Following was the chemical composition of the fumes-stainless steel: 57% Fe, 20% Cr, 14% Mn, and 9% Ni; mild steel: 83% Fe and 15% Mn. There was no effect of the mild steel fume on lung injury/inflammation at any time point compared to air control. Lung injury and inflammation were significantly elevated at 8 and 21 days after exposure to the stainless steel fume compared to control. Stainless steel fume exposure was associated with greater recovery of welding fume-laden macrophages from the lungs at all time points compared with the mild steel fume. A higher concentration of total metal was observed in the lungs of the stainless steel welding fume at all time points compared with the mild steel fume. The specific metals present in the two fumes were cleared from the lungs at different rates. The potentially more toxic metals (e.g., Mn, Cr) present in the stainless steel fume were cleared from the lungs more quickly than Fe, likely increasing their translocation from the respiratory system to other organs.

Learning from history, predicting the future: the UK Dutch elm disease outbreak in relation to contemporary tree disease threats

PubMed Central

Potter, Clive; Harwood, Tom; Knight, Jon; Tomlinson, Isobel

2011-01-01

Expanding international trade and increased transportation are heavily implicated in the growing threat posed by invasive pathogens to biodiversity and landscapes. With trees and woodland in the UK now facing threats from a number of disease systems, this paper looks to historical experience with the Dutch elm disease (DED) epidemic of the 1970s to see what can be learned about an outbreak and attempts to prevent, manage and control it. The paper draws on an interdisciplinary investigation into the history, biology and policy of the epidemic. It presents a reconstruction based on a spatial modelling exercise underpinned by archival research and interviews with individuals involved in the attempted management of the epidemic at the time. The paper explores what, if anything, might have been done to contain the outbreak and discusses the wider lessons for plant protection. Reading across to present-day biosecurity concerns, the paper looks at the current outbreak of ramorum blight in the UK and presents an analysis of the unfolding epidemiology and policy of this more recent, and potentially very serious, disease outbreak. The paper concludes by reflecting on the continuing contemporary relevance of the DED experience at an important juncture in the evolution of plant protection policy. PMID:21624917

Formulation and Assessment of a Wash-Primer Containing Lanthanum "Tannate" for Steel Temporary Protection

NASA Astrophysics Data System (ADS)

D'Alessandro, Oriana; Selmi, Gonzalo J.; Deyá, Cecilia; Di Sarli, Alejandro; Romagnoli, Roberto

2018-02-01

Tannins are polyphenols synthesized by plants and useful for the coating industry as corrosion inhibitors. In addition, lanthanum salts have a great inhibitory effect on steel corrosion. The aim of this study was to obtain lanthanum "tannate" with adequate solubility to be incorporated as the corrosion inhibitor in a wash-primer. The "tannate" was obtained from commercial "Quebracho" tannin and 0.1 M La(NO3)3. The soluble tannin was determined by the Folin-Denis reagent, while the concentration of Lanthanum was obtained by a gravimetric procedure. The protective action of "tannate" on SAE 1010 steel was evaluated by linear polarization curves and corrosion potential measurements. Lanthanum "tannate" was incorporated in a wash-primer formulation and tested by corrosion potential and ionic resistance measurements. The corrosion rate was also determined by the polarization resistance technique. Besides, the primer was incorporated in an alkyd paint system and its anticorrosion performance assessed in the salt spray cabinet and by electrochemical impedance spectroscopy. Results showed that lanthanum "tannate" primer inhibits the development of deleterious iron oxyhydroxides on the steel substrate and incorporated into a paint system had a similar behavior to the primer formulated with zinc tetroxychromate.

Performance of weathered steel guardrail in NC.

DOT National Transportation Integrated Search

2011-05-23

Weathered steel beam guardrail is a popular alternative to galvanized steel guardrail as an aesthetic solution that blends in with the surrounding natural environment. A research study from New Hampshire found that weathered steel guardrail deteriora...

What's in a name? Nominative determinism in the UK dental workforce.

PubMed

Sleigh, J

2016-12-16

Background Nominative determinism describes the theory that people are more likely to pursue careers that are connected to their names. Compelling research has been carried out across the medical professions that provides strong evidence for this phenomenon, but as yet its applicability to the UK dental workforce remains unknown.Aim The aim of this study was to establish the prevalence of dentally-related surnames in the UK dental workforce (dentists and dental care professionals) and compare this to the UK population.Results Dentistry may provide a surprising counter-example to prevailing theories of nominative determinism, as UK dentists are significantly less likely than the UK general population to have dentally-related surnames. This new phenomenon of 'nominative antideterminism' was not observed in the dental care professional (DCP) cohort, for whom the prevalence of dentally-related surnames was similar to that in the wider UK population.

UK medical selection: lottery or meritocracy?

PubMed

Harris, Benjamin H L; Walsh, Jason L; Lammy, Simon

2015-02-01

From senior school through to consultancy, a plethora of assessments shape medical careers. Multiple methods of assessment are used to discriminate between applicants. Medical selection in the UK appears to be moving increasingly towards non-knowledge-based testing at all career stages. We review the evidence for non-knowledge-based tests and discuss their perceived benefits. We raise the question: is the current use of non-knowledge-based tests within the UK at risk of undermining more robust measures of medical school and postgraduate performance? © 2015 Royal College of Physicians.

Advances in genome studies in plants and animals.

PubMed

Appels, R; Nystrom-Persson, J; Keeble-Gagnere, G

2014-03-01

The area of plant and animal genomics covers the entire suite of issues in biology because it aims to determine the structure and function of genetic material. Although specific issues define research advances at an organism level, it is evident that many of the fundamental features of genome structure and the translation of encoded information to function share common ground. The Plant and Animal Genome (PAG) conference held in San Diego (California), in January each year provides an overview across all organisms at the genome level, and often it is evident that investments in the human area provide leadership, applications, and discoveries for researchers studying other organisms. This mini-review utilizes the plenary lectures as a basis for summarizing the trends in the genome-level studies of organisms, and the lectures include presentations by Ewan Birney (EBI, UK), Eric Green (NIH, USA), John Butler (NIST, USA), Elaine Mardis (Washington, USA), Caroline Dean (John Innes Centre, UK), Trudy Mackay (NC State University, USA), Sue Wessler (UC Riverside, USA), and Patrick Wincker (Genoscope, France). The work reviewed is based on published papers. Where unpublished information is cited, permission to include the information in this manuscript was obtained from the presenters.

Patterns and Trends in UK Higher Education 2016

ERIC Educational Resources Information Center

Universities UK, 2016

2016-01-01

This report provides an interim update to the Universities UK "Patterns" series, before the publication of the full "Patterns and Trends" publication in spring 2017. It includes updates of the main charts included in the 2015 publication, covering trends in student and staff numbers and finances of the UK higher education…

Is Communications a Strategic Activity in UK Education?

ERIC Educational Resources Information Center

Chapleo, Chris

2006-01-01

This qualitative exploratory paper investigates whether communications/public relations is regarded by opinion formers in UK education as a strategic business activity or a tactical marketing tool. It is based upon depth interviews with 16 senior managers with strategic roles in UK higher or further education, or Government bodies, conducted…

The IB Diploma and UK University Degree Qualifications

ERIC Educational Resources Information Center

Frank-Gemmill, Gerda

2013-01-01

In recent years the International Baccalaureate (IB) Diploma has become widely accepted as a university-entry qualification in the UK, but there has been little quantitative research into the achievements of IB students at degree level. This study investigates IB students from one selective independent school who entered UK universities between…

UK Hazard Assessment for a Laki-type Volcanic Eruption

NASA Astrophysics Data System (ADS)

Witham, Claire; Felton, Chris; Daud, Sophie; Aspinall, Willy; Braban, Christine; Loughlin, Sue; Hort, Matthew; Schmidt, Anja; Vieno, Massimo

2014-05-01

Following the impacts of the Eyjafjallajokull eruption in 2010, two types of volcanic eruption have been added to the UK Government's National Risk Register for Civil Emergencies. One of these, a large gas-rich volcanic eruption, was identified as a high impact natural hazard, one of the three highest priority natural hazards faced by the UK. This eruption scenario is typified by the Laki eruption in Iceland in 1783-1784. The Civil Contingency Secretariat (CCS) of the UK's Cabinet Office, responsible for Civil Protection in the UK, has since been working on quantifying the risk and better understanding its potential impacts. This involves cross-cutting work across UK Government departments and the wider scientific community in order to identify the capabilities needed to respond to an effusive eruption, to exercise the response and develop increased resilience where possible. As part of its current work, CCS has been working closely with the UK Met Office and other UK agencies and academics (represented by the co-authors and others) to generate and assess the impacts of a 'reasonable worst case scenario', which can be used for decision making and preparation in advance of an eruption. Information from the literature and the findings of an expert elicitation have been synthesised to determine appropriate eruption source term parameters and associated uncertainties. This scenario is then being used to create a limited ensemble of model simulations of the dispersion and chemical conversion of the emissions of volcanic gases during such an eruption. The UK Met Office's NAME Lagrangian dispersion model and the Centre for Ecology and Hydrology's EMEP4UK Eulerian model are both being used. Modelling outputs will address the likelihood of near-surface concentrations of sulphur and halogen species being above specified health thresholds. Concentrations at aviation relevant altitudes will also be evaluated, as well as the effects of acid deposition of volcanic species on

Continuous steel production and apparatus

DOEpatents

Peaslee, Kent D [Rolla, MO; Peter, Jorg J [McMinnville, OR; Robertson, David G. C. [Rolla, MO; Thomas, Brian G [Champaign, IL; Zhang, Lifeng [Trondheim, NO

2009-11-17

A process for continuous refining of steel via multiple distinct reaction vessels for melting, oxidation, reduction, and refining for delivery of steel continuously to, for example, a tundish of a continuous caster system, and associated apparatus.

Risk of lung cancer according to mild steel and stainless steel welding.

PubMed

Sørensen, Anita Rath; Thulstrup, Ane Marie; Hansen, Johnni; Ramlau-Hansen, Cecilia Høst; Meersohn, Andrea; Skytthe, Axel; Bonde, Jens Peter

2007-10-01

Whether the elevated risk of lung cancer observed among welders is caused by welding emissions or by confounding from smoking or asbestos exposure is still not resolved. This question was addressed in a cohort with a long follow-up and quantified estimates of individual exposure to welding fume particulates. Male metal workers employed at least 1 year at one or more Danish stainless or mild steel industrial companies from 1964 through 1984 were enrolled in a cohort. Data on occupational and smoking history were obtained by questionnaire in 1986. Welders in the cohort who started welding in 1960 or later (N=4539) were followed from April 1968 until December 2003, when information on cancer diagnosis was obtained from the Danish Cancer Registry. During the follow-up, 75 cases of primary lung cancer were identified. Lifetime accumulated exposure to welding fume particulates was estimated by combining questionnaire information and more than 1000 welding-process-specific measurements of fume particulates in the Danish welding industry. The standardized incidence ratio (SIR) for lung cancer was increased among the welders [SIR 1.35, 95% confidence interval (95% CI) 1.06-1.70)]. Among the stainless steel welders, the risk increased significantly with increasing accumulative welding particulate exposure, while no exposure-response relation was found for mild steel welders, even after adjustment for tobacco smoking and asbestos exposure. The study corroborates earlier findings that welders have an increased risk of lung cancer. While exposure-response relations indicate carcinogenic effects related to stainless steel welding, it is still unresolved whether the mild steel welding process carries a carcinogenic risk.

New Generation Energy Efficient Refractory Application in Soaking Pits of Bhilai Steel Plant, Sail

NASA Astrophysics Data System (ADS)

Roy, Indranil; Chintaiah, Perumetla; Bhattacharya, Ajoy Kr.; Garai, Swapan Kr.; Ray Choudhury, Pankaj Kr.; Tiwari, Laksman

In Bhilai Steel Plant (BSP), soaking pits are used for heating ingots for successive rolling into blooms. Pits are operated at a temperature of around 1350°C. Mixed gas (Mixture of Blast Furnace gas & Coke Oven gas) of calorific value around 2040 kcal/Nm3 is used as fuel. The walls of soaking pits were lined with traditional 38% Al2O3 firebricks and top 500mm was cast with 70% Al2O3 low cement castable (LCC). This type of lining results in frequent damages due to hitting by ingots while being lifted from pit by overhead cranes thus affecting the availability of pit. Life of pits was 2 to 2.5 years in BSP with 3-4 cold repairs and 3-4 hot repairs. Energy loss through the wall is also quite high in this type of lining. To triumph over the limitations of the conventional lining, a lining design was developed for the walls which consist of special 70% Al2O3 LCC having high hot strength (HMOR) in combination with specially design flexible SS-304 anchors. Ceramic fiber blanket and insulation bricks were provided between castable and the metallic shell of the pit to minimize the heat loss. A heating schedule was developed and introduced based on available infrastructure at BSP for proper curing of modified LCC based lining. After introduction of modified lining, pit no. 14/2 is running for more than 2.5 years without any repair. To capitalize the success, two more pits i.e. 12/1 and 9/2 were converted to modified lining. These pits are also running satisfactorily for more than 1.5 years. The modification has resulted in higher availability with substantial increase in production. Shell temperature of the modified pits reduced to 90° - 140°C from 120° - 200°C of conventional pits. This shows reduction in heat loss through walls, resulting less fuel consumption and energy saving of about 18%.

Preformed posterior stainless steel crowns: an update.

PubMed

Croll, T P

1999-02-01

For almost 50 years, dentists have used stainless steel crowns for primary and permanent posterior teeth. No other type of restoration offers the convenience, low cost, durability, and reliability of such crowns when interim full-coronal coverage is required. Preformed stainless steel crowns have improved over the years. Better luting cements have been developed and different methods of crown manipulation have evolved. This article reviews stainless steel crown procedures for primary and permanent posterior teeth. Step-by-step placement of a primary molar stainless steel crown is documented and permanent molar stainless steel crown restoration is described. A method for repairing a worn-through crown also is reviewed.

High yttria ferritic ODS steels through powder forging

NASA Astrophysics Data System (ADS)

Kumar, Deepak; Prakash, Ujjwal; Dabhade, Vikram V.; Laha, K.; Sakthivel, T.

2017-05-01

Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y2O3 (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility.

Fracture Characteristics of Structural Steels: Reference Manual

DTIC Science & Technology

1979-04-01

materials were fractured undcr tensile, fatigue, and impact loading con- ditions. The effects of hydrogen embrittlement on the steels ’ behavior when...years after paint failure. The composition and the heat treatment of 4160 steel results in a steel extremely susceptible to stress corrosion cracking and...A35 Fracture Surface of Tensile Specimen No. 3 322 22 IL TABLES Number Page 1 Chemical Composition of Steels and Weld Metal 32 2 Welding Parameters 33

Stress among UK Academics: Identifying Who Copes Best

ERIC Educational Resources Information Center

Darabi, Mitra; Macaskill, Ann; Reidy, Lisa

2017-01-01

This article examined levels of stress and associated coping strategies among UK academics. Adopting a positive psychology approach, the influence of the character strengths of hope, optimism, gratitude and self-efficacy on stress, subjective well-being (SWB), and mental health was examined in 216 academics in a UK university. The study explored…

Monitoring of hot pipes at the power plant Neurath using guided waves

NASA Astrophysics Data System (ADS)

Weihnacht, Bianca; Klesse, Thomas; Neubeck, Robert; Schubert, Lars

2013-04-01

In order to reduce the CO2-emissions and to increase the energy efficiency, the operating temperatures of power plants will be increased up to 720°C. This demands for novel high-performance steels in the piping systems. Higher temperatures lead to a higher risk of damage and have a direct impact on the structure stability and the deposition structure. Adequately trusted results for the prediction of the residual service life of those high strength steels are not available so far. To overcome these problems the implementation of an online monitoring system in addition to periodic testing is needed. RWE operates the lignite power plant Neurath. All test and research activities have to be checked regarding their safety and have to be coordinated with the business operation of the plant. An extra bypass was established for this research and made the investigations independent from the power plant operating. In order to protect the actuators and sensors from the heat radiated from the pipe, waveguides were welded to the bypass. The data was evaluated regarding their dependencies on the environmental influences like temperature and correction algorithms were developed. Furthermore, damages were introduced into the pipe with diameters of 8 mm to 10 mm and successfully detected by the acoustic method.

Antimicrobial thin films based on ayurvedic plants extracts embedded in a bioactive glass matrix

NASA Astrophysics Data System (ADS)

Floroian, L.; Ristoscu, C.; Candiani, G.; Pastori, N.; Moscatelli, M.; Mihailescu, N.; Negut, I.; Badea, M.; Gilca, M.; Chiesa, R.; Mihailescu, I. N.

2017-09-01

Ayurvedic medicine is one of the oldest medical systems. It is an example of a coherent traditional system which has a time-tested and precise algorithm for medicinal plant selection, based on several ethnopharmacophore descriptors which knowledge endows the user to adequately choose the optimal plant for the treatment of certain pathology. This work aims for linking traditional knowledge with biomedical science by using traditional ayurvedic plants extracts with antimicrobial effect in form of thin films for implant protection. We report on the transfer of novel composites from bioactive glass mixed with antimicrobial plants extracts and polymer by matrix-assisted pulsed laser evaporation into uniform thin layers onto stainless steel implant-like surfaces. The comprehensive characterization of the deposited films was performed by complementary analyses: Fourier transformed infrared spectroscopy, glow discharge optical emission spectroscopy, scanning electron microscopy, atomic force microscopy, electrochemical impedance spectroscopy, UV-VIS absorption spectroscopy and antimicrobial tests. The results emphasize upon the multifunctionality of these coatings which allow to halt the leakage of metal and metal oxides into the biological fluids and eventually to inner organs (by polymer use), to speed up the osseointegration (due to the bioactive glass use), to exert antimicrobial effects (by ayurvedic plants extracts use) and to decrease the implant price (by cheaper stainless steel use).

A mortality study among mild steel and stainless steel welders.

PubMed Central

Moulin, J J; Wild, P; Haguenoer, J M; Faucon, D; De Gaudemaris, R; Mur, J M; Mereau, M; Gary, Y; Toamain, J P; Birembaut, Y

1993-01-01

A mortality study was carried out in conjunction with the European mortality study among welders coordinated by the International Agency for Research on Cancer (IARC). The study was aimed at assessing risks for lung cancer in relation to exposure to asbestos, welding fumes containing chromium and nickel, and tobacco smoke. The study included a cohort of 2721 welders and an internal comparison group of 6683 manual workers employed in 13 factories in France. The mortality of the two cohorts was studied from 1975 to 1988 by the historical prospective method. Job histories of welders were traced including welding processes used, metals welded, and proportion of worktime spent in welding. Data on smoking habits were collected from medical records. The observed number of deaths were compared with those expected (standardised mortality ratio (SMR)) based on national rates with adjustments for age, sex, and calendar time. The smoking habits of 87% of the whole study population were known. The distribution of welders and controls according to smoking was not statistically different. The overall mortality was slightly higher for welders (SMR = 1.02, 95% confidence interval (95% CI) 0.89-1.18) than for controls (SMR = 0.91, 95% CI 0.84-0.99). For lung cancer, the SMR was 1.24 (95% CI 0.75-1.94) for welders, whereas the corresponding value was lower for controls (SMR = 0.94, 95% CI 0.68-1.26). The SMR for lung cancer was 1.59 among non-shipyard mild steel welders (95% CI 0.73-3.02). This contrasted with the results for all stainless steel welders (SMR = 0.92, 95% CI 0.19-2.69), and for stainless steel welders predominantly exposed to chromium VI (SMR = 1.03, 95% CI 0.12-3.71). Moreover, SMRs for lung cancer for mild steel welders tended to increase with duration of exposure and time since first exposure, leading to significant excesses for duration > or = 20 years and latency > or = 20 years. Such a pattern was not found for stainless steel welders. PMID:8457490

Anodized Steel Electrodes for Supercapacitors.

PubMed

Sagu, Jagdeep S; Wijayantha, K G Upul; Bohm, Mallika; Bohm, Siva; Kumar Rout, Tapan

2016-03-09

Steel was anodized in 10 M NaOH to enhance its surface texture and internal surface area for application as an electrode in supercapacitors. A mechanism was proposed for the anodization process. Field-emission gun scanning electron microscopy (FEGSEM) studies of anodized steel revealed that it contains a highly porous sponge like structure ideal for supercapacitor electrodes. X-ray photoelectron spectroscopy (XPS) measurements showed that the surface of the anodized steel was Fe2O3, whereas X-ray diffraction (XRD) measurements indicated that the bulk remained as metallic Fe. The supercapacitor performance of the anodized steel was tested in 1 M NaOH and a capacitance of 18 mF cm(-2) was obtained. Cyclic voltammetry measurements showed that there was a large psueudocapacitive contribution which was due to oxidation of Fe to Fe(OH)2 and then further oxidation to FeOOH, and the respective reduction of these species back to metallic Fe. These redox processes were found to be remarkably reversible as the electrode showed no loss in capacitance after 10000 cycles. The results demonstrate that anodization of steel is a suitable method to produce high-surface-area electrodes for supercapacitors with excellent cycling lifetime.

Fatigue life assessment of 316L stainless steel and DIN-1.4914 martensitic steel before and after TEXTOR exposure

NASA Astrophysics Data System (ADS)

Shakib, J. I.; Ullmaier, H.; Little, E. A.; Schmitz, W.; Faulkner, R. G.; Chung, T. E.

1992-09-01

The effects of plasma exposure in the TEXTOR tokomak on elevated temperature fatigue lifetime and failure micromechanisms of 316L austenitic stainless steel and DIN 1.4914 martensitic steel (NET reference heats) have been evaluated. Fatigue tests were carried out in vacuum in the temperature range 150°-450°C and compared with data from reference specimens.Plasma-induced surface modifications lead to significant deterioration in fatigue life of 316L steel, whereas the lifetime of 1.4914 steel is unaffected. Fatigue in the 1.4914 steel is surface-initiated only at high stresses. At low stress amplitudes internal fatigue initiation at inclusions was observed.

Determination of beryllium concentrations in UK ambient air

NASA Astrophysics Data System (ADS)

Goddard, Sharon L.; Brown, Richard J. C.; Ghatora, Baljit K.

2016-12-01

Air quality monitoring of ambient air is essential to minimise the exposure of the general population to toxic substances such as heavy metals, and thus the health risks associated with them. In the UK, ambient air is already monitored under the UK Heavy Metals Monitoring Network for a number of heavy metals, including nickel (Ni), arsenic (As), cadmium (Cd) and lead (Pb) to ensure compliance with legislative limits. However, the UK Expert Panel on Air Quality Standards (EPAQS) has highlighted a need to limit concentrations of beryllium (Be) in air, which is not currently monitored, because of its toxicity. The aim of this work was to analyse airborne particulate matter (PM) sampled onto filter papers from the UK Heavy Metals Monitoring Network for quantitative, trace level beryllium determination and compare the results to the guideline concentration specified by EPAQS. Samples were prepared by microwave acid digestion in a matrix of 2% sulphuric acid and 14% nitric acid, verified by the use of Certified Reference Materials (CRMs). The digested samples were then analysed by Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The filters from the UK Heavy Metals Monitoring Network were tested using this procedure and the average beryllium concentration across the network for the duration of the study period was 7.87 pg m-3. The highest site average concentration was 32.0 pg m-3 at Scunthorpe Low Santon, which is significantly lower than levels that are thought to cause harm. However the highest levels were observed at sites monitoring industrial point sources, indicating that beryllium is being used and emitted, albeit at very low levels, from these point sources. Comparison with other metals concentrations and data from the UK National Atmospheric Emissions Inventory suggests that current emissions of beryllium may be significantly overestimated.

Comparative Review of UK-USA Industry-University Relationships

ERIC Educational Resources Information Center

Decter, Moira H.

2009-01-01

Purpose: The purpose of this paper is to explore significant historical changes, legislation and policy in the UK and USA from the 1960s to present day relating to university-industry relationships. Design/methodology/approach: The paper presents a review of papers, reports and policy documents from the UK and USA drawing comparisons of…

Mapping the Information Systems Curricula in UK Universities

ERIC Educational Resources Information Center

Stefanidis, Angelos; Fitzgerald, Guy

2010-01-01

Information Systems (IS) undergraduate student numbers in the UK have reduced by half in the last five years. An increasing number of researchers have been pondering the possible relationship between the modernity of IS curricula and its attractiveness to potential students. To support the debate about IS curricula in the UK and elsewhere, this…

Universities UK Submission to the 2010 Spending Review

ERIC Educational Resources Information Center

Universities UK, 2010

2010-01-01

This document represents the submission of Universities UK to the 2010 Spending Review. It sets out why the authors believe universities are critical to the UK's future economic growth, what the impact of cuts to the budget for higher education would be, and the activities which universities are currently pursuing to secure national economic…

Spark Plasma Co-Sintering of Mechanically Milled Tool Steel and High Speed Steel Powders

PubMed Central

Pellizzari, Massimo; Fedrizzi, Anna; Zadra, Mario

2016-01-01

Hot work tool steel (AISI H13) and high speed steel (AISI M3:2) powders were successfully co-sintered to produce hybrid tool steels that have properties and microstructures that can be modulated for specific applications. To promote co-sintering, which is made difficult by the various densification kinetics of the two steels, the particle sizes and structures were refined by mechanical milling (MM). Near full density samples (>99.5%) showing very fine and homogeneous microstructure were obtained using spark plasma sintering (SPS). The density of the blends (20, 40, 60, 80 wt % H13) was in agreement with the linear rule of mixtures. Their hardness showed a positive deviation, which could be ascribed to the strengthening effect of the secondary particles altering the stress distribution during indentation. A toughening of the M3:2-rich blends could be explained in view of the crack deviation and crack arrest exerted by the H13 particles. PMID:28773603

Spark Plasma Co-Sintering of Mechanically Milled Tool Steel and High Speed Steel Powders.

PubMed

Pellizzari, Massimo; Fedrizzi, Anna; Zadra, Mario

2016-06-16

Hot work tool steel (AISI H13) and high speed steel (AISI M3:2) powders were successfully co-sintered to produce hybrid tool steels that have properties and microstructures that can be modulated for specific applications. To promote co-sintering, which is made difficult by the various densification kinetics of the two steels, the particle sizes and structures were refined by mechanical milling (MM). Near full density samples (>99.5%) showing very fine and homogeneous microstructure were obtained using spark plasma sintering (SPS). The density of the blends (20, 40, 60, 80 wt % H13) was in agreement with the linear rule of mixtures. Their hardness showed a positive deviation, which could be ascribed to the strengthening effect of the secondary particles altering the stress distribution during indentation. A toughening of the M3:2-rich blends could be explained in view of the crack deviation and crack arrest exerted by the H13 particles.

UK parliamentary debate analysis: bombing ISIL in Syria.

PubMed

Rashed, Haifa

2016-01-01

This paper examines the arguments presented for and against the UK government's motion for the UK to intervene militarily in Syria in the House of Commons debate on ISIL in Syria that took place on 2 December 2015. It considers what the most common arguments were in favour of and in opposition to the motion as well as which arguments were given the most emphasis, in order to understand the prime justifications given that led to the decision to approve the motion. It suggests that due to the shadow of the 2003 Iraq war, politicians in the debate placed a considerable emphasis on the legal justification for military intervention. It argues that the focus on the national security of the UK and its allies in this particular debate seems to contrast with previous military interventions where humanitarian motives were more widely stated. This paper calls for further comparative research of parliamentary debates in order to track such changes in the rhetoric used by UK politicians to defend their support for military intervention.

An Experimental Study on the Shear Hysteresis and Energy Dissipation of the Steel Frame with a Trapezoidal-Corrugated Steel Plate.

PubMed

Shon, Sudeok; Yoo, Mina; Lee, Seungjae

2017-03-06

The steel frame reinforced with steel shear wall is a lateral load resisting system and has higher strength and shear performance than the concrete shear wall system. Especially, using corrugated steel plates in these shear wall systems improves out-of-plane stiffness and flexibility in the deformation along the corrugation. In this paper, a cyclic loading test of this steel frame reinforced with trapezoidal-corrugated steel plate was performed to evaluate the structural performance. The hysteresis behavior and the energy dissipation capacity of the steel frame were also compared according to the corrugated direction of the plate. For the test, one simple frame model without the wall and two frame models reinforced with the plate are considered and designed. The test results showed that the model reinforced with the corrugated steel plate had a greater accumulated energy dissipation capacity than the experimental result of the non-reinforced model. Furthermore, the energy dissipation curves of two reinforced frame models, which have different corrugated directions, produced similar results.

Effect of Welding Processes on the Microstructure, Mechanical Properties and Residual Stresses of Plain 9Cr-1Mo Steel Weld Joints

NASA Astrophysics Data System (ADS)

Nagaraju, S.; Vasantharaja, P.; Brahadees, G.; Vasudevan, M.; Mahadevan, S.

2017-12-01

9Cr-1Mo steel designated as P9 is widely used in the construction of power plants and high-temperature applications. It is chosen for fabricating hexcan fuel subassembly wrapper components of fast breeder reactors. Arc welding processes are generally used for fabricating 9Cr-1Mo steel weld joints. A-TIG welding process is increasingly being adopted by the industries. In the present study, shielded metal arc (SMA), tungsten inert gas (TIG) and A-TIG welding processes are used for fabricating the 9Cr-1Mo steel weld joints of 10 mm thickness. Effect of the above welding processes on the microstructure evolution, mechanical properties and residual stresses of the weld joints has been studied in detail. All the three weld joints exhibited comparable strength and ductility values. 9Cr-1Mo steel weld joint fabricated by SMAW process exhibited lower impact toughness values caused by coarser grain size and inclusions. 9Cr-1Mo steel weld joint fabricated by TIG welding exhibited higher toughness due to finer grain size, while the weld joint fabricated by A-TIG welding process exhibited adequate toughness values. SMA steel weld joint exhibited compressive residual stresses in the weld metal and HAZ, while TIG and A-TIG weld joint exhibited tensile residual stresses in the weld metal and HAZ.

Use of natural radionuclides to determine the time range of the accidental melting of an orphan radioactive source in a steel recycling plant.

PubMed

Cantaluppi, Chiara; Ceccotto, Federica; Cianchi, Aldo

2012-02-01

In the rare event that an orphan radioactive source is melted in an Electric Arc Furnace steel recycling plant, the radionuclides present are partitioned in the different products, by-products and waste. As a consequence of an unforeseen melting of a radiocesium source, cesium radioisotopes can be found in the dust, together with many natural radionuclides from the decay of radon and thoron, which are present in the atmosphere, picked up from the off-gas evacuation system and associated with the dust of the air filtration system ("baghouse"). In this work we verified that the activity concentration of ²¹²Pb in this dust is essentially constant in a specific factory so that it is possible to use it to date back to the time of the accidental melting of the orphan radioactive source. The main features of this method are described below, together with the application to a particular case in which this method was used for dating the moment in which the dust was contaminated with ¹³⁷Cs. Copyright © 2011 Elsevier Ltd. All rights reserved.

The effect of steel chemistry on the formation of Fe-Zn intermetallic compounds of galvanneal-coated steel sheets

NASA Astrophysics Data System (ADS)

Lin, C. S.; Meshii, M.

1994-10-01

The effects of steel chemistry on the formation of Fe-Zn intermetallic compounds in the galvanneal coatings have been investigated by examining the microstructure of galvanneal coat-ings on extra-low-carbon (ELC) steel, interstitial-free (IF) steel, and interstitial-free rephos-phorized (IFP) steel. The layer structure of the coatings was revealed by chemical etching. Phases present in each layer were then identified using electron diffraction in transmission elec-tron microscopy (TEM). A two-layer structure, one consisting of the δ phase with a small fraction of the ζ, phase dispersed on the surface and Γ phases and another consisting of the δ and Γ1 phases, was observed in the ELC sample and the IFP sample, respectively. A three-layer structure consisting of the δ, Γ1 + δ, and Γ phases was observed in the IF sample. The presence of C in the steel substrate retarded the alloying between Fe and Zn; while P in the steel favored the formation of the Γ1, phase over the Γ phase by its surface segregation in the steel substrate. The orientation relationship between coating and substrate was also studied by electron diffraction. Three α-Fe/Γ orientation relationships were frequently observed.

The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes.

PubMed

Kelly, Jack; Knottenbelt, William

2015-01-01

Many countries are rolling out smart electricity meters. These measure a home's total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the 'ground truth' demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset.

Patterns and Trends in UK Higher Education, 2011

ERIC Educational Resources Information Center

Universities UK, 2011

2011-01-01

This report builds on the time series data produced annually since 2001 under the title "Patterns of higher education institutions in the UK." It offers a unique overview of provision at publicly-funded higher education institutions in the UK. All charts and tables in the report are now also available to download from the Universities UK…

Safer Schools in the UK--A Case Study

ERIC Educational Resources Information Center

Hayden, Carol; Holt, Amanda; Martin, Denise; Nee, Claire

2011-01-01

This article reports a research that is based on a European Safer Schools Partnership that included ten countries and specifically the UK case study which was located in London. The initiators of this partnership had been involved in early SSPs in the UK and the educationalists were very much focussed on work that would address problematic…

UK report on waste management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferguson, J.

1995-09-01

Arising jointly from the National and European Union requirements for more intensive attention to be paid to the environment, the United Kingdom (UK) has taken many strides forward in protecting the environment from pollution and preventing harm to human health arising from the handling, transport and disposal of wastes. Major adjustments are taking place in Europe following the opening up of the Eastern European countries. The consequences of the illegal movement of wastes and its mistreatment and disposal are now recognised within the European Union. The UK as a member State is well aware of the consequences which arise frommore » the lack of proper waste management. This paper discusses waste management and legislation pertaining to waste management in the United Kingdom.« less

29 CFR 1926.757 - Open web steel joists.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Open web steel joists. 1926.757 Section 1926.757 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.757 Open web steel joists. (a) General. (1) Except as provided in paragraph (a)(2) of this section, where steel joists are used...

29 CFR 1926.757 - Open web steel joists.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Open web steel joists. 1926.757 Section 1926.757 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.757 Open web steel joists. (a) General. (1) Except as provided in paragraph (a)(2) of this section, where steel joists are used...

The influence of fire exposure on austenitic stainless steel for pressure vessel fitness-for-service assessment: Experimental research

NASA Astrophysics Data System (ADS)

Li, Bo; Shu, Wenhua; Zuo, Yantian

2017-04-01

The austenitic stainless steels are widely applied to pressure vessel manufacturing. The fire accident risk exists in almost all the industrial chemical plants. It is necessary to make safety evaluation on the chemical equipment including pressure vessels after fire. Therefore, the present research was conducted on the influences of fire exposure testing under different thermal conditions on the mechanical performance evolution of S30408 austenitic stainless steel for pressure vessel equipment. The metallurgical analysis described typical appearances in micro-structure observed in the material suffered by fire exposure. Moreover, the quantitative degradation of mechanical properties was investigated. The material thermal degradation mechanism and fitness-for-service assessment process of fire damage were further discussed.

Tobacco industry manipulation of data on and press coverage of the illicit tobacco trade in the UK.

PubMed

Rowell, A; Evans-Reeves, K; Gilmore, A B

2014-05-01

In the UK, transnational tobacco companies (TTCs) have been arguing that levels of illicit trade are high and increasing and will rise further if standardised packaging is implemented. This paper examines trends in and accuracy of media reporting of, and industry data on, illicit tobacco in the UK. Quantification of the volume, nature and quality of press articles citing industry data on illicit tobacco in UK newspapers from March 2008 to March 2013. Examination of published TTC data on illicit, including a comparison with independent data and of TTC reporting of Her Majesty's Revenue and Customs data on illicit. Media stories citing industry data on illicit tobacco began in June 2011, 2 months after the Tobacco Control Plan for England, which heralded standardised packaging, was published. The majority of data cited are based on industry Empty Pack Surveys for which no methodology is available. For almost all parts of the country where repeat data were cited in press stories, they indicated an increase, often substantial, in non-domestic/illicit cigarettes that is not supported by independent data. Similarly, national data from two published industry sources show a sudden large increase in non-domestic product between 2011 and 2012. Yet the methodology of one report changes over this period and the other provides no published methodology. In contrast, independent data show steady declines in non-domestic and illicit cigarette penetration from 2006 to 2012 and either a continued decline or small increase to 2013. Industry claims that use of Non-UK Duty Paid/illicit cigarettes in the UK is sharply increasing are inconsistent with historical trends and recent independent data. TTCs are exaggerating the threat of illicit tobacco by commissioning surveys whose methodology and validity remain uncertain, planting misleading stories and misquoting government data. Industry data on levels of illicit should be treated with extreme caution. Published by the BMJ Publishing

Tobacco industry manipulation of data on and press coverage of the illicit tobacco trade in the UK

PubMed Central

Rowell, A; Evans-Reeves, K; Gilmore, A B

2014-01-01

Background In the UK, transnational tobacco companies (TTCs) have been arguing that levels of illicit trade are high and increasing and will rise further if standardised packaging is implemented. This paper examines trends in and accuracy of media reporting of, and industry data on, illicit tobacco in the UK. Methods Quantification of the volume, nature and quality of press articles citing industry data on illicit tobacco in UK newspapers from March 2008 to March 2013. Examination of published TTC data on illicit, including a comparison with independent data and of TTC reporting of Her Majesty's Revenue and Customs data on illicit. Results Media stories citing industry data on illicit tobacco began in June 2011, 2 months after the Tobacco Control Plan for England, which heralded standardised packaging, was published. The majority of data cited are based on industry Empty Pack Surveys for which no methodology is available. For almost all parts of the country where repeat data were cited in press stories, they indicated an increase, often substantial, in non-domestic/illicit cigarettes that is not supported by independent data. Similarly, national data from two published industry sources show a sudden large increase in non-domestic product between 2011 and 2012. Yet the methodology of one report changes over this period and the other provides no published methodology. In contrast, independent data show steady declines in non-domestic and illicit cigarette penetration from 2006 to 2012 and either a continued decline or small increase to 2013. Conclusions Industry claims that use of Non-UK Duty Paid/illicit cigarettes in the UK is sharply increasing are inconsistent with historical trends and recent independent data. TTCs are exaggerating the threat of illicit tobacco by commissioning surveys whose methodology and validity remain uncertain, planting misleading stories and misquoting government data. Industry data on levels of illicit should be treated with extreme

19 CFR 360.104 - Steel import monitoring.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 3 2010-04-01 2010-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing requirement...

19 CFR 360.104 - Steel import monitoring.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 3 2011-04-01 2011-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing requirement...

19 CFR 360.104 - Steel import monitoring.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 3 2014-04-01 2014-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing requirement...

19 CFR 360.104 - Steel import monitoring.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 3 2012-04-01 2012-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing requirement...

19 CFR 360.104 - Steel import monitoring.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 3 2013-04-01 2013-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing requirement...

Malnutrition in the UK.

PubMed

Blades, Mabel

2013-05-01

Malnutrition is estimated to cost the UK twice that of obesity every year, but it is still an often overlooked problem. Dr Mabel Blades, a freelance Registered Dietician and Nutritionist, looks at the problems that malnutrition presents and the solutions that we can use to combat it.

46 CFR 154.172 - Contiguous steel hull structure.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for the...

46 CFR 154.172 - Contiguous steel hull structure.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for the...

46 CFR 154.172 - Contiguous steel hull structure.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for the...

46 CFR 154.172 - Contiguous steel hull structure.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for the...

49 CFR 178.504 - Standards for steel drums.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for steel drums. 178.504 Section 178.504...-bulk Performance-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for...

49 CFR 178.504 - Standards for steel drums.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable head...

49 CFR 178.504 - Standards for steel drums.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable head...