MS2 inactivation by TiO2 nanoparticles in the presence of quartz sand

NASA Astrophysics Data System (ADS)

Syngouna, Vasiliki I.; Chrysikopoulos, Constantinos V.

2017-04-01

Virus inactivation by nanoparticles (NPs) is hypothesized to affect virus fate and transport in the subsurface. This study examines the interactions of viruses with titanium dioxide (TiO2) anatase NPs, which is a good disinfectant with unique physiochemical properties, using three different virus concentrations. The bacteriophage MS2 was used as a model virus. A series of batch experiments of MS2 inactivation by TiO2 NPs were conducted at room temperature (25 °C), in the presence of quartz sand, with and without ambient light. The virus inactivation experimental data were satisfactorily fitted with a pseudo-first order expression with a time dependent rate coefficient. Quartz sand was shown to affect MS2 inactivation by TiO2 NPs both in the presence and absence of ambient light, because, under the experimental conditions of this study, the quartz sand offers a protection to the attached MS2 against inactivation. Moreover, in most cases similar inactivation rates were observed in reactor and control tubes (absence of TiO2 NPs) suggesting that low TiO2 concentration (10 mg/L) affects only slightly MS2 inactivation with and without ambient light.

Transport of carboxyl-functionalized carbon black nanoparticles in saturated porous media: Column experiments and model analyses

NASA Astrophysics Data System (ADS)

Kang, Jin-Kyu; Yi, In-Geol; Park, Jeong-Ann; Kim, Song-Bae; Kim, Hyunjung; Han, Yosep; Kim, Pil-Je; Eom, Ig-Chun; Jo, Eunhye

2015-06-01

The aim of this study was to investigate the transport behavior of carboxyl-functionalized carbon black nanoparticles (CBNPs) in porous media including quartz sand, iron oxide-coated sand (IOCS), and aluminum oxide-coated sand (AOCS). Two sets of column experiments were performed under saturated flow conditions for potassium chloride (KCl), a conservative tracer, and CBNPs. Breakthrough curves were analyzed to obtain mass recovery and one-dimensional transport model parameters. The first set of experiments was conducted to examine the effects of metal (Fe, Al) oxides and flow rate (0.25 and 0.5 mL min- 1) on the transport of CBNPs suspended in deionized water. The results showed that the mass recovery of CBNPs in quartz sand (flow rate = 0.5 mL min- 1) was 83.1%, whereas no breakthrough of CBNPs (mass recovery = 0%) was observed in IOCS and AOCS at the same flow rate, indicating that metal (Fe, Al) oxides can play a significant role in the attachment of CBNPs to porous media. In addition, the mass recovery of CBNPs in quartz sand decreased to 76.1% as the flow rate decreased to 0.25 mL min- 1. Interaction energy profiles for CBNP-porous media were calculated using DLVO theory for sphere-plate geometry, demonstrating that the interaction energy for CBNP-quartz sand was repulsive, whereas the interaction energies for CBNP-IOCS and CBNP-AOCS were attractive with no energy barriers. The second set of experiments was conducted in quartz sand to observe the effect of ionic strength (NaCl = 0.1 and 1.0 mM; CaCl2 = 0.01 and 0.1 mM) and pH (pH = 4.5 and 5.4) on the transport of CBNPs suspended in electrolyte. The results showed that the mass recoveries of CBNPs in NaCl = 0.1 and 1.0 mM were 65.3 and 6.4%, respectively. The mass recoveries of CBNPs in CaCl2 = 0.01 and 0.1 mM were 81.6 and 6.3%, respectively. These results demonstrated that CBNP attachment to quartz sand can be enhanced by increasing the electrolyte concentration. Interaction energy profiles demonstrated that the interaction energy profile for CBNP-quartz sand was compressed and that the energy barrier decreased as the electrolyte concentration increased. Furthermore, the mass recovery of CBNPs in the presence of divalent ions (CaCl2 = 0.1 mM) was far lower than that in the presence of monovalent ions (NaCl = 0.1 mM), demonstrating a much stronger effect of Ca2 + than Na+ on CBNP transport. Mass recovery of CBNPs at pH 4.5 was 55.6%, which was lower than that (83.1%) at pH 5.4, indicating that CBNP attachment to quartz sand can be enhanced by decreasing the pH. The sticking efficiencies (α) calculated from the mass recovery by colloid filtration theory were in the range from 2.1 × 10- 2 to 4.5 × 10- 1, which were far greater than the values (2.56 × 10- 6-3.33 × 10- 2) of theoretical sticking efficiencies (αtheory) calculated from the DLVO energy by the Maxwell model.

Interface Modeling for Electro-Osmosis in Subgrade Structures

DTIC Science & Technology

2004-12-01

aggregate and different clays ( kaolinite , montmorillonite , limestone and quartz sands) created to simulate below grade structures. A direct current 30...Quartz Sand 100 Sieve Ca Montmorillonite Na Montmorillonite Kaolinite The test setup used a 0.45 water to cement ratio concrete cylinder... Kaolinite cell Figure 4. Measured pH for Concrete and Na Montmorillonite cell 4 Scaling occurred at the interface between the anode

Analysis of MASTER Thermal Data in the Greeley Area of the Front Range Urban Corridor, Colorado--Delineation of Sites for Infrastructure Resource Characterization

USGS Publications Warehouse

Livo, K. Eric; Watson, Ken

2002-01-01

Sand and soils southwest of Greeley, Colorado, were characterized for mineral composition and industrial quality. Radi-ance data from the thermal channels of the MASTER simulator were calibrated using estimated atmospheric parameters. Chan-nel emissivities were approximated using an estimated ground temperature. Subsequently, a decorrelation algorithm was used to calculate inverse wave emissivity images. Six soil classes, one vegetation class, water, and several small classes were defined using an unsupervised classification algorithm. Ground covered by each of the derived emissivity spectral classes was studied using color-infrared air photos, color-infrared composite MAS-TER data, geologic maps, NASA/JPL Airborne Visible and Infra-red Imaging Spectrometer (AVIRIS) data, and field examination. Spectral classes were characterized by their responses and related to their mineral content through field examination. Classes with a minimum at channel 44, and having a similar spectral shape to quartz, field checked as containing abundant quartz. Classes with a minimum at channel 45, and having a spectral shape similar to the sheet minerals, were found in the field to contain abundant mica and clay. Sandy soil was found to have a positive slope at the longer wavelengths; the more clay rich soils had a negative slope. Spectra with a strong downturn at channel 50 generally indicated low vegetation cover, whereas an upturn indicated more vegetation cover. Mapping revealed a range of classified soils with varying amounts of quartz, silt, clay, and plant humus. Sand and gravel operations along the St. Vrain River, gravel lots, and some fields spectrally classified as quartz-rich sands were confirmed through field examination. Other fields mapped as sandy soils, ranging from quartz-rich sandy soil to quartz-rich silt-sand soil with clay. Flood plains mapped as sandy-silty-organic-rich clay. The city of Greeley contained all classes of materials, with the sand classes mapping as various types of asphalt. Abundant quartz gravel was apparent within the asphalt during field check-ing. The clay classes mapped silt-clay soils in areas of irrigated grass landscaping, some fields, and roofing materials.

Experimental studies of shock-induced particle jetting

NASA Astrophysics Data System (ADS)

Xue, Kun; Du, Kaiyuan; Shi, Xiaoliang

2018-05-01

The dispersion of particle rings or shells by a radially divergent shock front trailed by the pressurized gases takes the form of hierarchical particle jetting. Through a semi-two-dimensional configuration, we characterize the evolution of the jetting pattern using the boundary tracking technique. In contrast to the refined filamentary jetting spread induced by the dispersal of soft and ductile flour particles, the hard and brittle quartz sand particles are dispersed into a finger-like branched pattern with much fewer jets. The interplay between the primary and secondary jets suffices to reverse the flour jetting pattern, which by contrast is negligible in the quartz sand jetting. The distinct jetting patterns displayed by the flour and quartz sand particles are related with the distinguishable networks of force chains invoked in two particles which dictate the nucleation of jets.

Mineralogic maturity of modern sand along a high-energy tropical coast: Baixada de Jacarepaguá, Rio de Janeiro, Brazil

NASA Astrophysics Data System (ADS)

Savage, K. M.; de Cesero, P.; Potter, P. E.

Quarts arenites overlying crystalline basement are fairly common in the geologic record. A modern analog is provided in coastal Brazil where a small tropical lowland is bordered by abrupt, Precambrian granitic and gneissic mountains of the Serra do Mar. Nine different sedimentary environments were sampled, 57 sands were studied petrographically, and 8 complete chemical analyses were made. Here, arkosic river sands pass seaward into well defined, quartz-rich, stranded beach ridges and pure quartz arenites of the modern beach and shelf. Strong inshore wave power combined with tropical weathering seem to be the principal factors for this change. Tropical weathering also converted surface samples of arkosic Pliocene fan deposits into residual quartz arenites. Implications for the paleotectonic and paleoclimatic interpretation of ancient sandstones are also discussed.

Characterization of minerals in natural and manufactured sand in Cauvery River belt, Tamilnadu, India

NASA Astrophysics Data System (ADS)

Gnanasaravanan, S.; Rajkumar, P.

2013-05-01

The present study investigates the characterization of minerals in the River Sand (R - Sand) and the Manufactured sand (M-Sand) through FTIR spectroscopic studies. The R - Sand is collected from seven different locations in Cauvery River and M - Sand is collected from eight different manufactures around the Cauvery River belt in Salem, Erode, Tirupur and Namakkal districts of Tamilnadu, India. To extend the effectiveness of the analysis, the samples were subjected to grain size separation to classify the bulk samples into different grain sizes. All the samples were analyzed using FTIR spectrometer. The number of minerals identified with the help of FTIR spectra in overall (bulk) samples of R - Sand is 14 and of M - Sand is 13. The number has been increased while going for grain size separation, i.e., from 14 to 31 for R - Sand and from 13 to 20 for M - Sand. Among all minerals, quartz plays a major role. The relative distribution and the crystallinity nature of quartz have been discussed based on the extinction co-efficient and the crystallinity index values computed. There is no major variation found in M - Sand while going for grain size separation.

Provenance of sands from the confluence of the Amazon and Madeira rivers based on detrital heavy minerals and luminescence of quartz and feldspar

NASA Astrophysics Data System (ADS)

do Nascimento, Daniel R.; Sawakuchi, André O.; Guedes, Carlos C. F.; Giannini, Paulo C. F.; Grohmann, Carlos H.; Ferreira, Manuela P.

2015-03-01

Source-to-sink systems are poorly known in tropical rivers. For the Amazonian rivers, the majority of the provenance studies remain focused on the suspended load, implying a poor understanding of the processes governing production and distribution of sands. In this study, we perform heavy mineral and optically stimulated luminescence (OSL) analysis to cover the entire spectrum (heavy and light minerals fraction) of 29 sand samples of the Lower Madeira river region (Amazon and Madeira rivers), of which the main goal was to find provenance indicators specific to these rivers. Despite the tropical humid climate, the sands of the Amazon and Lower Madeira rivers are rich in unstable heavy minerals as augite, hypersthene, green hornblende and andalusite. The Madeira river is highlighted by its higher content of andalusite, with source attributed to the Amazon Craton (medium-to-high grade metamorphic rocks), while the Amazon river, upstream of the Madeira river mouth, has a signature of augite and hypersthene, that suggests an Andean provenance (volcanic rocks). Sands from the Madeira river can be tracked in the Amazon river by the increasing concentration in andalusite. OSL analysis of the light minerals fraction was used as an index of feldspar concentration and sedimentary history of quartz grains. Lower feldspar concentration and quartz grains with longer sedimentary history (higher OSL sensitivity) also point to a major contribution of cratonic sources for the sands in the Madeira river. While the sands from the Lower Madeira would be mainly supplied by cratonic rocks, previous work recognised that suspended sediments (silt and clay) are derived from Andean rocks. Therefore, we interpret a decoupling between the sources of sand and mud (silt and clay) under transport in the Madeira river. Andean sands (rich in augite and hypersthene) would be trapped in the foreland zones of the Beni and Mamoré tributaries. In the Amazon river sands, the low OSL sensitivity of the quartz, higher content of feldspar and unstable heavy mineral assemblage dominated by augite and hypersthene suggest both a fast transport from Andean sources with fine sediment bypass over foreland areas.

Water softening by induced crystallization in fluidized bed.

PubMed

Chen, Yuefang; Fan, Rong; An, Danfeng; Cheng, Yujie; Tan, Hazel

2016-12-01

Fluidized bed and induced crystallization technology were combined to design a new type of induced crystallization fluidized bed reactor. The added particulate matter served as crystal nucleus to induce crystallization so that the insoluble material, which was in a saturated state, could precipitate on its surface. In this study, by filling the fluidized bed with quartz sand and by adjusting water pH, precipitation of calcium carbonate was induced on the surface of quartz sand, and the removal of water hardness was achieved. With a reactor influent flow of 60L/hr, a fixed-bed height of 0.5m, pH value of 9.5, quartz sand nuclear diameter of 0.2-0.4mm, and a reflux ratio of 60%, the effluent concentration of calcium hardness was reduced to 60mg/L and 86.6% removal efficiency was achieved. The resulting effluent reached the quality standard set for circulating cooling water. Majority of the material on the surface of quartz sand was calculated to be calcium carbonate based on energy spectrum analysis and moisture content was around 15.994%. With the low moisture content, dewatering treatment is no longer required and this results to cost savings on total water treatment process. Copyright © 2016. Published by Elsevier B.V.

Production of silica gel from Tunisian sands and its adsorptive properties

NASA Astrophysics Data System (ADS)

Lazaar, K.; Hajjaji, W.; Pullar, R. C.; Labrincha, J. A.; Rocha, F.; Jamoussi, F.

2017-06-01

Thanks to its highly absorbent character, silica gel is used in several applications, such as air moisture removal, as a treatment agent for effluents. In this study, silica gels were synthesised from Tunisian sands, collected from the Fortuna and Sidi Aich Formations in northern and central Tunisia. The collected quartz sand raw materials, as well as the prepared silica gels, were characterised by different techniques, such as X-ray diffraction (XRD), X-ray fluorescence (XRF) and scanning electron microscopy (SEM). XRD patterns of quartz sands showed quartz as main phase (86.1-98%), with lower contents of potassic feldspars, along with kaolinite and calcite. These quartz sands presented relatively small quantities of Fe2O3 (0.3%-0.5%) and TiO2 (0.1%-0.6%). The synthesised silica gels exhibited pore diameters exceeding 20 Å and surface areas up to 194 m2/g, comparable with those described in the literature and commercial silica gel. N2 adsorption isotherms showed that the silica gels prepared from Tunisian sands are mesoporous materials with high adsorption capacities. To understand better their adsorbent properties and applicability on an industrial scale, these gels were tested for methylene blue (MB) absorption. Maximum decolourisation rates (up to 96% after a contact time of 180 min) occurred with products synthesised at pH 3. The adsorption mechanism fitted better with a Langmuir model, revealing a monolayer coverage process of MB molecules over the gel surface, and the adsorption kinetics of the dye on these materials is well described by the second order model. The corresponding equilibrium adsorption capacities obtained from experimental data (Qexp = 292-214 mg/g) were close to the estimated maximum adsorption capacities (Qe = 333-250 mg/g), and to that of an industrial silica gel (250 mg/g).

Decolorization of black liquor from bioethanol G2 production using iron oxide coating sands

NASA Astrophysics Data System (ADS)

Barlianti, Vera; Triwahyuni, Eka; Waluyo, Joko; Sari, Ajeng Arum

2017-01-01

Bioethanol G2 production using oil palm empty fruit bunch as raw material consists of four steps, namely pretreatment, hydrolysis, fermentation, and purification process. Pretreatment process generates black liquor that causes serious environmental pollution if it is released to the environment. The objective of this research is studying the ability of iron oxide coating sands to adsorb the color of black liquor. The iron oxide coating sands were synthesized from FeCl3.6H2O with quartz sands as support material. This research was conducted on batch mode using black liquor in various pH values. Result obtained that kind of iron oxide on quartz sands's surface was goethite. The result also indicated decreasing of color intensity of black liquor after adsorption process. This research supports local material utilization in environmental technology development to solve some environmental problems.

Transport of selected bacterial pathogens in agricultural soil and quartz sand.

PubMed

Schinner, Tim; Letzner, Adrian; Liedtke, Stefan; Castro, Felipe D; Eydelnant, Irwin A; Tufenkji, Nathalie

2010-02-01

The protection of groundwater supplies from microbial contamination necessitates a solid understanding of the key factors controlling the migration and retention of pathogenic organisms through the subsurface environment. The transport behavior of five waterborne pathogens was examined using laboratory-scale columns packed with clean quartz at two solution ionic strengths (10 mM and 30 mM). Escherichia coli O157:H7 and Yersinia enterocolitica were selected as representative Gram-negative pathogens, Enterococcus faecalis was selected as a representative Gram-positive organism, and two cyanobacteria (Microcystis aeruginosa and Anabaena flos-aquae) were also studied. The five organisms exhibit differing attachment efficiencies to the quartz sand. The surface (zeta) potential of the microorganisms was characterized over a broad range of pH values (2-8) at two ionic strengths (10 mM and 30 mM). These measurements are used to evaluate the observed attachment behavior within the context of the DLVO theory of colloidal stability. To better understand the possible link between bacterial transport in model quartz sand systems and natural soil matrices, additional experiments were conducted with two of the selected organisms using columns packed with loamy sand obtained from an agricultural field. This investigation highlights the need for further characterization of waterborne pathogen surface properties and transport behavior over a broader range of environmentally relevant conditions. Copyright 2008 Elsevier Ltd. All rights reserved.

Transport and retention of 14C-perfluorooctanoic acid (PFOA) in saturated limestone and sand porous media: Effects of input concentration, ionic strength and cation type

NASA Astrophysics Data System (ADS)

Xueyan, L.; Gao, B.; Sun, Y.; Wu, J.

2017-12-01

Perfluorooctanoic acid (PFOA) has been used in a wide variety of industrial and consumer product applications. PFOA has been detected around the world at ng/L to μg/L levels in groundwater, and at ng/g levels in soil.The physicochemical properties of porous media were proven to play pivotal roles in determining the transport behavior of various pollutants. It is anticipated that physicochemical properties of porous media will strongly influence the transport behavior of PFOA. In addition, previous investigations have revealed that input concentration significantly influence the transport behavior of nanoparticles and antibiotics. Thus, this study was designed experimentally and fundamentally to gain insight into transport and retention of PFOA in various porous medias at different input concentrations, solution IS and cation type. Unlike in quartz sand porous media, the BTCs in limestone porous media exhibited increasing retention rate and high degree of tailing in limestone porous media. Results showed that higher relative retention occurred in limestone porous media than in quartz sand porous media under the same solution chemistry. This result was attributed to the less negative zeta-potentials, rougher surface and larger specific surface area, and the presence of hydroxyl groups and organic matters of limestone grains. Higher ionic strength and Ca2+ had little impact on the mobility of PFOA in quartz sand porous media, but significantly enhanced the retention of PFOA in limestone porous media. The difference is likely due to the compression of the electrical double layer, and the surface-charge neutralization and cation-bridging effect of Ca2+. Higher input concentration resulted in lower relative PFOA retention in limestone porous media, but the influence were insignificant in quartz sand porous media. This effect is likely because attachment sites in limestone responced to the variety of input concentration differently than quartz.

XRD and mineralogical analysis of gypsum dunes at White Sands National Monument, New Mexico and applications to gypsum detection on Mars

NASA Astrophysics Data System (ADS)

Lafuente, B.; Bishop, J. L.; Fenton, L. K.; King, S. J.; Blake, D.; Sarrazin, P.; Downs, R.; Horgan, B. H.

2013-12-01

A field portable X-ray Diffraction (XRD) instrument was used at White Sands National Monument to perform in-situ measurements followed by laboratory analyses of the gypsum-rich dunes and to determine its modal mineralogy. The field instrument is a Terra XRD (Olympus NDT) based on the technology of the CheMin (Chemistry and Mineralogy) instrument onboard the Mars Science Laboratory (MSL) rover Curiosity which is providing the mineralogical and chemical composition of scooped soil samples and drilled rock powders collected at Gale Crater [1]. Using Terra at White Sands will contribute to 'ground truth' for gypsum-bearing environments on Mars. Together with data provided by VNIR spectra [2], this study clarifies our understanding of the origin and history of gypsum-rich sand dunes discovered near the northern polar region of Mars [3]. The results obtained from the field analyses performed by XRD and VNIR spectroscopy in four dunes at White Sands revealed the presence of quartz and dolomite. Their relative abundance has been estimated using the Reference Intensity Ratio (RIR) method. For this study, particulate samples of pure natural gypsum, quartz and dolomite were used to prepare calibration mixtures of gypsum-quartz and gypsum-dolomite with the 90-150μm size fractions. All single phases and mixtures were analyzed by XRD and RIR factors were calculated. Using this method, the relative abundance of quartz and dolomite has been estimated from the data collected in the field. Quartz appears to be present in low amounts (2-5 wt.%) while dolomite is present at percentages up to 80 wt.%. Samples from four dunes were collected and prepared for subsequent XRD analysis in the lab to estimate their composition and illustrate the changes in mineralogy with respect to location and grain size. Gypsum-dolomite mixtures: The dolomite XRD pattern is dominated by an intense diffraction peak at 2θ≈36 deg. which overlaps a peak of gypsum, This makes low concentrations of dolomite difficult to quantify in mixtures with high concentration of gypsum. Dolomite has been detected in some locations at dune 3 as high as 80 wt.%. Gypsum-quartz mixtures: The intensity of the main diffraction peak of quartz at 2θ≈31 deg. decreases progressively with the decrease of the amount of quartz in the mixtures. Samples from dune 1 and 2 show quartz abundance at 5.6 and 2.6 wt.% respectively . [1] Blake et al. Space Sci. Rev. (2012). doi:10.1007/s11214-012-9905-1. [2] King et al. (2013) AGU, submitted. [3] Langevin et al. (2005). Science 307, 1584-1586.

Mineral dissolution and secondary precipitation on quartz sand in simulated Hanford tank solutions affecting subsurface porosity

NASA Astrophysics Data System (ADS)

Wang, Guohui; Um, Wooyong

2012-11-01

Highly alkaline nuclear waste solutions have been released from underground nuclear waste storage tanks and pipelines into the vadose zone at the US Department of Energy's Hanford Site in Washington, causing mineral dissolution and re-precipitation upon contact with subsurface sediments. High pH caustic NaNO3 solutions with and without dissolved Al were reacted with quartz sand through flow-through columns stepwise at 45, 51, and 89 °C to simulate possible reactions between leaked nuclear waste solution and primary subsurface mineral. Upon reaction, Si was released from the dissolution of quartz sand, and nitrate-cancrinite [Na8Si6Al6O24(NO3)2] precipitated on the quartz surface as a secondary mineral phase. Both steady-state dissolution and precipitation kinetics were quantified, and quartz dissolution apparent activation energy was determined. Mineral alteration through dissolution and precipitation processes results in pore volume and structure changes in the subsurface porous media. In this study, the column porosity increased up to 40.3% in the pure dissolution column when no dissolved Al was present in the leachate, whereas up to a 26.5% porosity decrease was found in columns where both dissolution and precipitation were observed because of the presence of Al in the input solution. The porosity change was also confirmed by calculation using the dissolution and precipitation rates and mineral volume changes.

Adhesion kinetics of viable Cryptosporidium parvum oocysts to quartz surfaces.

PubMed

Kuznar, Zachary A; Elimelech, Menachem

2004-12-15

The transport and deposition (adhesion) kinetics of viable Cryptosporidium parvum oocysts onto ultrapure quartz surfaces in a radial stagnation point flow system were investigated. Utilizing an optical microscope and an image-capturing device enabled real time observation of oocyst deposition behavior onto the quartz surface in solutions containing either monovalent (KCl) or divalent (CaCl2) salts. Results showed a significantly lower oocyst deposition rate in the presence of a monovalent salt compared to a divalent salt. With a monovalent salt, oocyst deposition rates and corresponding attachment efficiencies were relatively low, even at high KCl concentrations where Derjaguin-Landau-Verwey-Overbeek (DLVO) theory predicts the absence of an electrostatic energy barrier. On the other hand, in the presence of a divalent salt, oocyst deposition rates increased continuously as the salt concentration was increased over the entire range of ionic strengths investigated. The unusually low deposition rate in a monovalent salt solution is attributed to "electrosteric" repulsion between the Cryptosporidium oocyst and the quartz surface, most likely due to proteins on the oocyst surface that extend into the solution. It is further proposed that specific binding of calcium ions to the oocyst surface functional groups results in charge neutralization and conformational changes of surface proteins that significantly reduce electrosteric repulsion.

Reduced transport potential of a palladium-doped zero valent iron nanoparticle in a water saturated loamy sand.

PubMed

Basnet, Mohan; Di Tommaso, Caroline; Ghoshal, Subhasis; Tufenkji, Nathalie

2015-01-01

Direct in situ injection of palladium-doped nanosized zero valent iron (Pd-NZVI) particles can contribute to remediation of various environmental contaminants. A major challenge encountered is rapid aggregation of Pd-NZVI and hence very limited mobility. To reduce aggregation and concurrently improve particle mobility, the surface of bare Pd-NZVI can be modified with stabilizing surface modifiers. Selected surface-modified Pd-NZVI has shown dramatically improved stability and transport. However, little is known regarding the effects of aquifer grain geochemical heterogeneity on the transport and deposition behavior of surface-modified Pd-NZVI. Herein, the mobility of surface stabilized Pd-NZVI in two granular matrices representative of model ground water environments (quartz sand and loamy sand) was assessed over a wide range of environmentally relevant ionic strengths (IS). Carboxymethyl cellulose (CMC), soybean flour and rhamnolipid biosurfactant were used as Pd-NZVI surface modifiers. Our results show that, both in quartz sand and loamy sand, an increase in solution IS results in reduced Pd-NZVI transport. Moreover, at a given water chemistry, Pd-NZVI transport is notably attenuated in loamy sand implying that geochemical heterogeneity associated with loamy sand is a key factor influencing Pd-NZVI transport potential. Experiments conducted at a higher Pd-NZVI particle concentration, to be more representative of field conditions, show that rhamnolipid and CMC are effective stabilizing agents even when 1 g/L Pd-NZVI is injected into quartz sand. Overall, this study emphasizes the extent to which variation in groundwater chemistry, coupled with changes in aquifer geochemistry, could dramatically alter the transport potential of Pd-NZVI in the subsurface environment.

Investing the temporal and spatial scale variations of luminescence sensitivity of loess in the Chinese Loess Plateau since the last interglacial

NASA Astrophysics Data System (ADS)

Lv, T.; Sun, J.; Gong, Z.

2017-12-01

The provenance of the eolian deposits on the Loess Plateau has long been one of the most important issues. Although the luminescence sensitivity of the quartz grains of desert sands has been used in tracing provenance, and the vertical variation of OSL sensitivity of Loess in the central Chinese Loess plateau (CLP) has been studied, it still remains uncertain about the temporal and spatial scale variations of luminescence sensitivity of loess. This paper chose the eolian deposits of Shimao (SM) section in the northern margin of the Chinese Loess Plateau and of Luochuan (LC) section in the central Chinese Loess Plateau. Firstly, the temporal scale variations of luminescence sensitivity of different quartz grians (38-64 and 64-90μm) from sand/loess of SM section have been studied respectively. Our results indicate that they both have similar trend in the strength of luminescence sensitivity, characterized by lower values in sand/loess beds and higher values in soils. The OSL sensitivity of quartz grains of the sand-loess-soil sequence shows very similar trend to the magnetic susceptibility fluctuations. Secondly, the spatial scale variations of luminescence sensitivity of loess in the Chinese Loess Plateau since the last interglacial were studied by comparing the values of SM section and LC section. The OSL sensitivity of quartz grains from the two sections since the last interglacial change synchronously. However, the OSL sensitivity values of quartz grains from the same loess/paleosol beds of LC section are higher than these values of SM section. We suggest that the temporal variation of OSL sensitivity of SM is main influenced by the retreat-advance of deserts. The spatial variation of OSL sensitivity mainly is due to the different sedimentary history, containing of repeated erosion, transport and deposition cycles which controlled by cyclic climatic change. The higher OSL sensitivity values of quartz grains in LC section relates of longer transport distance and of more sedimentary history than these values in SM section. Keywords: Luminescence sensitivity; Quartz; provenance; Loess Plateau

Thermal conductivity measurements in porous mixtures of methane hydrate and quartz sand

USGS Publications Warehouse

Waite, W.F.; deMartin, B.J.; Kirby, S.H.; Pinkston, J.; Ruppel, C.D.

2002-01-01

Using von Herzen and Maxwell's needle probe method, we measured thermal conductivity in four porous mixtures of quartz sand and methane gas hydrate, with hydrate composing 0, 33, 67 and 100% of the solid volume. Thermal conductivities were measured at a constant methane pore pressure of 24.8 MPa between -20 and +15??C, and at a constant temperature of -10??C between 3.5 and 27.6 MPa methane pore pressure. Thermal conductivity decreased with increasing temperature and increased with increasing methane pore pressure. Both dependencies weakened with increasing hydrate content. Despite the high thermal conductivity of quartz relative to methane hydrate, the largest thermal conductivity was measured in the mixture containing 33% hydrate rather than in hydrate-free sand. This suggests gas hydrate enhanced grain-to-grain heat transfer, perhaps due to intergranular contact growth during hydrate synthesis. These results for gas-filled porous mixtures can help constrain thermal conductivity estimates in porous, gas hydrate-bearing systems.

Investigation of formaldehyde interaction with carbon nanotubes and quartz sand

NASA Astrophysics Data System (ADS)

Georgopoulou, Maria P.; Chrysikopoulos, Constantinos V.

2017-04-01

Assessment of the potential impact of synthetic carbon nanotubes on the fate and transport of common chemical contaminants (pesticides, pharmaceuticals, etc.) in groundwater systems is considered to be an increasingly important aspect of environmental research. This study investigates the interaction of formaldehyde with multi-walled carbon nanotubes (MWCNTs) and quartz sand under static and dynamic conditions. Due to polarity, formaldehyde, is expected to develop strong adsorptive interactions with carbon nanotubes. Several batch adsorption experiments were conducted in test tubes, under controlled conditions. Various initial formaldehyde solution concentration (2, 5, 8 ppm), contact times, and temperatures (8, 18, 25 °C) were considered. Supernatant liquid samples were collected at regular intervals, and centrifuged. Subsequently, the formaldehyde concentration in the supernatant was quantified indirectly, by derivatization with Nash reagent and subsequent measurement of the resulting complex using spectrophotometry in the visible spectral range. Experimental results suggested that formaldehyde has a low affinity for quartz sand, but an enhanced potential for adsorption onto carbon nanotubes. Formaldehyde adsorption onto both absorbents (quartz sand and MWCNTs) was more pronounced under dynamic than static conditions, probably, because agitation improves the mixing of the absorbent within the solution. Also, it was shown that the adsorption data were adequately described by the pseudo-second order kinetic model, suggesting that the primary adsorption mechanism was chemisorption, where two or more (sequential or parallel) processes (e.g. surface chemisorption, intraparticle diffusion) were taking place. Therefore, MWCNTs could be promising adsorbent materials for groundwater remediation.

Remediation of arsenic-contaminated groundwater using media-injected permeable reactive barriers with a modified montmorillonite: sand tank studies.

PubMed

Luo, Ximing; Liu, Haifei; Huang, Guoxin; Li, Ye; Zhao, Yan; Li, Xu

2016-01-01

A modified montmorillonite (MMT) was prepared using an acid activation-sodium activation-iron oxide coating method to improve the adsorption capacities of natural MMTs. For MMT, its interlamellar distance increased from 12.29 to 13.36 Å, and goethite (α-FeOOH) was intercalated into its clay layers. Two novel media-injected permeable reactive barrier (MI-PRB) configurations were proposed for removing arsenic from groundwater. Sand tank experiments were conducted to investigate the performance of the two MI-PRBs: Tank A was filled with quartz sand. Tank B was packed with quartz sand and zero-valent iron (ZVI) in series, and the MMT slurry was respectively injected into them to form reactive zones. The results showed that for tank A, total arsenic (TA) removal of 98.57% was attained within the first 60 mm and subsequently descended slowly to 88.84% at the outlet. For tank B, a similar spatial variation trend was observed in the quartz sand layer, and subsequently, TA removal increased to ≥99.80% in the ZVI layer. TA removal by MMT mainly depended on both surface adsorption and electrostatic adhesion. TA removal by ZVI mainly relied on coagulation/precipitation and adsorption during the iron corrosion. The two MI-PRBs are feasible alternatives for in situ remediation of groundwater with elevated As levels.

A Preliminary Design of a Calibration Chamber for Evaluating the Stability of Unsaturated Soil Slope

NASA Astrophysics Data System (ADS)

Hsu, H.-H.

2012-04-01

The unsaturated soil slopes, which have ground water tables and are easily failure caused by heavy rainfalls, are widely distributed in the arid and semi-arid areas. For analyzing the stability of slope, in situ tests are the direct methods to obtain the test site characteristics. The cone penetration test (CPT) is a popular in situ test method. Some of the CPT empirical equations established from calibration chamber tests. The CPT performed in calibration chamber was commonly used clean quartz sand as testing material in the past. The silty sand is observed in many actual slopes. Because silty sand is relatively compressible than quartz sand, it is not suitable to apply the correlations between soil properties and CPT results built from quartz sand to silty sand. The experience on CPT calibration in silty sand has been limited. CPT calibration tests were mostly performed in dry or saturated soils. The condition around cone tip during penetration is assumed to be fully drained or fully undrained, yet it was observed to be partially drained for unsaturated soils. Because of the suction matrix has a great effect on the characteristics of unsaturated soils, they are much sensitive to the water content than saturated soils. The design of an unsaturated calibration chamber is in progress. The air pressure is supplied from the top plate and the pore water pressure is provided through the high air entry value ceramic disks located at the bottom plate of chamber cell. To boost and uniform distribute the unsaturated effect, four perforated burettes are installed onto the ceramic disks and stretch upwards to the midheight of specimen. This paper describes design concepts, illustrates this unsaturated calibration chamber, and presents the preliminary test results.

Mineral Dissolution and Secondary Precipitation on Quartz Sand in Simulated Hanford Tank Solutions Affecting Subsurface Porosity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Guohui; Um, Wooyong

2012-11-23

Highly alkaline nuclear waste solutions have been released from underground nuclear waste storage tanks and pipelines into the vadose zone at the U.S. Department of Energy’s Hanford Site in Washington, causing mineral dissolution and re-precipitation upon contact with subsurface sediments. High pH caustic NaNO3 solutions with and without dissolved Al were reacted with quartz sand through flow-through columns stepwise at 45, 51, and 89°C to simulate possible reactions between leaked nuclear waste solution and primary subsurface mineral. Upon reaction, Si was released from the dissolution of quartz sand, and nitrate-cancrinite [Na8Si6Al6O24(NO3)2] precipitated on the quartz surface as a secondary mineralmore » phase. Both steady-state dissolution and precipitation kinetics were quantified, and quartz dissolution apparent activation energy was determined. Mineral alteration through dissolution and precipitation processes results in pore volume and structure changes in the subsurface porous media. In this study, the column porosity increased up to 40.3% in the pure dissolution column when no dissolved Al was present in the leachate, whereas up to a 26.5% porosity decrease was found in columns where both dissolution and precipitation were observed because of the presence of Al in the input solution. The porosity change was also confirmed by calculation using the dissolution and precipitation rates and mineral volume changes.« less

Investigation of quartz grain surface textures by atomic force microscopy for forensic analysis.

PubMed

Konopinski, D I; Hudziak, S; Morgan, R M; Bull, P A; Kenyon, A J

2012-11-30

This paper presents a study of quartz sand grain surface textures using atomic force microscopy (AFM) to image the surface. Until now scanning electron microscopy (SEM) has provided the primary technique used in the forensic surface texture analysis of quartz sand grains as a means of establishing the provenance of the grains for forensic reconstructions. The ability to independently corroborate the grain type classifications is desirable and provides additional weight to the findings of SEM analysis of the textures of quartz grains identified in forensic soil/sediment samples. AFM offers a quantitative means of analysis that complements SEM examination, and is a non-destructive technique that requires no sample preparation prior to scanning. It therefore has great potential to be used for forensic analysis where sample preservation is highly valuable. By taking quantitative topography scans, it is possible to produce 3D representations of microscopic surface textures and diagnostic features for examination. Furthermore, various empirical measures can be obtained from analysing the topography scans, including arithmetic average roughness, root-mean-square surface roughness, skewness, kurtosis, and multiple gaussian fits to height distributions. These empirical measures, combined with qualitative examination of the surfaces can help to discriminate between grain types and provide independent analysis that can corroborate the morphological grain typing based on the surface textures assigned using SEM. Furthermore, the findings from this study also demonstrate that quartz sand grain surfaces exhibit a statistically self-similar fractal nature that remains unchanged across scales. This indicates the potential for a further quantitative measure that could be utilised in the discrimination of quartz grains based on their provenance for forensic investigations. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Experimental Study on Stress Monitoring of Sand-Filled Steel Tube during Impact Using Piezoceramic Smart Aggregates.

PubMed

Du, Guofeng; Zhang, Juan; Zhang, Jicheng; Song, Gangbing

2017-08-22

The filling of thin-walled steel tubes with quartz sand can help to prevent the premature buckling of the steel tube at a low cost. During an impact, the internal stress of the quartz sand-filled steel tube column is subjected to not only axial force but also lateral confining force, resulting in complicated internal stress. A suitable sensor for monitoring the internal stress of such a structure under an impact is important for structural health monitoring. In this paper, piezoceramic Smart Aggregates (SAs) are embedded into a quartz Sand-Filled Steel Tube Column (SFSTC) to monitor the internal structural stress during impacts. The piezoceramic smart aggregates are first calibrated by an impact hammer. Tests are conducted to study the feasibility of monitoring the internal stress of a structure. The results reflect that the calibration value of the piezoceramic smart aggregate sensitivity test is in good agreement with the theoretical value, and the output voltage value of the piezoceramic smart aggregate has a good linear relationship with external forces. Impact tests are conducted on the sand-filled steel tube with embedded piezoceramic smart aggregates. By analyzing the output signal of the piezoceramic smart aggregates, the internal stress state of the structure can be obtained. Experimental results demonstrated that, under the action of impact loads, the piezoceramic smart aggregates monitor the compressive stress at different locations in the steel tube, which verifies the feasibility of using piezoceramic smart aggregate to monitor the internal stress of a structure.

Effect of different-sized colloids on the transport and deposition of titanium dioxide nanoparticles in quartz sand.

PubMed

Cai, Li; Peng, Shengnan; Wu, Dan; Tong, Meiping

2016-01-01

Colloids (non-biological and biological) with different sizes are ubiquitous in natural environment. The investigations regarding the influence of different-sized colloids on the transport and deposition behaviors of engineered-nanoparticles in porous media yet are still largely lacking. This study investigated the effects of different-sized non-biological and biological colloids on the transport of titanium dioxide nanoparticles (nTiO2) in quartz sand under both electrostatically favorable and unfavorable conditions. Fluorescent carboxylate-modified polystyrene latex microspheres (CML) with sizes of 0.2-2 μm were utilized as model non-biological colloids, while Gram-negative Escherichia coli (∼ 1 μm) and Gram-positive Bacillus subtilis (∼ 2 μm) were employed as model biological colloids. Under the examined solution conditions, both breakthrough curves and retained profiles of nTiO2 with different-sized CML particles/bacteria were similar as those without colloids under favorable conditions, indicating that the copresence of model colloids in suspensions had negligible effects on the transport and deposition of nTiO2 under favorable conditions. In contrast, higher breakthrough curves and lower retained profiles of nTiO2 with CML particles/bacteria relative to those without copresent colloids were observed under unfavorable conditions. Clearly, the copresence of model colloids increased the transport and decreased the deposition of nTiO2 in quartz sand under unfavorable conditions (solution conditions examined in present study). Both competition of deposition sites on quartz sand surfaces and the enhanced stability/dispersion of nTiO2 induced by copresent colloids were found to be responsible for the increased nTiO2 transport with colloids under unfavorable conditions. Moreover, the smallest colloids had the highest coverage on sand surface and most significant dispersion effect on nTiO2, resulting in the greatest nTiO2 transport. Copyright © 2015. Published by Elsevier Ltd.

Quartz sand as "blank" compound in rehabilitation experience of industrial barren

NASA Astrophysics Data System (ADS)

Gorbacheva, T. T.; Ivanova, L. A.; Kikuchi, R.; Gerardo, R.

2010-05-01

During 2008 the field test was performed near the smelter complex Monchegorsk (67°51'N, 32°48'E) to estimate suitability of innovate method for site remediation in severe conditions such as in industrial barren. The method is based on cultivation of perennial grasses using hydroponics with thermally inflated vermiculite from local deposit (Kovdor) followed by rolled lawn placement on very contaminated sites near Monchegorsk. Growing in very contaminated ground resulted in 50% rolled lawn surface loss during first year but with biodiversity maintenance. Field experiment was carried out in three variants (1- mineral ground - flat site; 2- mineral ground- slope sites; 3- organogenic ground - flat site in depression in five replicates. More comprehensive results were received for mineral ground due to better natural washing compared to organogenic ground. In all variants we observed secondary roots formation. It seems obvious that plant roots choose the best zones of soils to grow, and that they avoided toxic zones. Observations continued during 2009 to follow freezing influence and nutrient loss rate. We observed grass survival of about 20-30% during second year of field test but grass roots proliferated very slowly in contaminated ground. Affinity to the ground is one of most important estimate of rolled lawn efficiency for grass cover creation. One of possible measure to improve rolled lawn affinity is to establish additional permeable barrier for grass roots isolation from toxic ground. Simultaneously with rolled lawn placement litterbag experiment was carried out with quartz sand as filling. Quartz was chosen as blank compound and as possible material for permeable barrier creation. Original quartz have some initial nutritional status: pH 6.87, available forms of K 1.9 mg g-1, Ca 9.5 mg g-1, Mg 2.8 mg g-1, P 0.4 mg g-1. There was both increasing and decreasing of quartz nutritional status during 2008-2009 period. Besides quartz is recognized to be some barrier for pollution load due to organic matter and related heavy metals and Al sorption onto a quartz sand surface. Laboratory pot experiment are planed to be carry out to estimate quartz barrier function efficiency for grass survival.

Effective removal of trace thallium from surface water by nanosized manganese dioxide enhanced quartz sand filtration.

PubMed

Huangfu, Xiaoliu; Ma, Chengxue; Ma, Jun; He, Qiang; Yang, Chun; Zhou, Jian; Jiang, Jin; Wang, Yaan

2017-12-01

Thallium (Tl) has drawn wide concern due to its high toxicity even at extremely low concentrations, as well as its tendency for significant accumulation in the human body and other organisms. The need to develop effective strategies for trace Tl removal from drinking water is urgent. In this study, the removal of trace Tl (0.5 μg L -1 ) by conventional quartz sand filtration enhanced by nanosized manganese dioxide (nMnO 2 ) has been investigated using typical surface water obtained from northeast China. The results indicate that nMnO 2 enhanced quartz sand filtration could remove trace Tl(I) and Tl(III) efficiently through the adsorption of Tl onto nMnO 2 added to a water matrix and onto nMnO 2 attached on quartz sand surfaces. Tl(III)-HA complexes might be responsible for higher residual Tl(III) in the effluent compared to residual Tl(I). Competitive Ca 2+ cations inhibit Tl removal to a certain extent because the Ca 2+ ions will occupy the Tl adsorption site on nMnO 2 . Moreover, high concentrations of HA (10 mgTOC L -1 ), which notably complexes with and dissolves nMnO 2 (more than 78%), resulted in higher residual Tl(I) and Tl(III). Tl(III)-HA complexes might also enhance Tl(III) penetration to a certain extent. Additionally, a higher pH level could enhance the removal of trace Tl from surface water. Finally, a slight increase of residual Tl was observed after backwash, followed by the reduction of the Tl concentration in the effluent to a "steady" state again. The knowledge obtained here may provide a potential strategy for drinking water treatment plants threatened by trace Tl. Copyright © 2017. Published by Elsevier Ltd.

Study on Production of Silicon Nanoparticles from Quartz Sand for Hybrid Solar Cell Applications

NASA Astrophysics Data System (ADS)

Arunmetha, S.; Vinoth, M.; Srither, S. R.; Karthik, A.; Sridharpanday, M.; Suriyaprabha, R.; Manivasakan, P.; Rajendran, V.

2018-01-01

Nano silicon (nano Si) particles were directly prepared from natural mineral quartz sand and thereafter used to fabricate the hybrid silicon solar cells. Here, in this preparation technique, two process stages were involved. In the first stage, the alkaline extraction and acid precipitation processes were applied on quartz sand to fetch silica nanoparticles. In the second stage, magnesiothermic and modified magnesiothermic reduction reactions were applied on nano silica particles to prepare nano Si particles. The effect of two distinct reduction methodologies on nano Si particle preparation was compared. The magnesiothermic and modified magnesiothermic reductions in the silica to silicon conversion process were studied with the help of x-ray diffraction (XRD) with intent to study the phase changes during the reduction reaction as well as its crystalline nature in the pure silicon phase. The particles consist of a combination of fine particles with spherical morphology. In addition to this, the optical study indicated an increase in visible light absorption and also increases the performance of the solar cell. The obtained nano Si particles were used as an active layer to fabricate the hybrid solar cells (HSCs). The obtained results confirmed that the power conversion efficiency (PCE) of the magnesiothermically modified nano Si cells (1.06%) is much higher as compared to the nano Si cells that underwent magnesiothermic reduction (1.02%). Thus, this confirms the increased PCE of the investigated nano Si solar cell up to 1.06%. It also revealed that nano Si behaved as an electron acceptor and transport material. The present study provided valuable insights and direction for the preparation of nano Si particles from quartz sand, including the influence of process methods. The prepared nano Si particles can be utilized for HSCs and an array of portable electronic devices.

Transport, retention, and long-term release behavior of ZnO nanoparticle aggregates in saturated quartz sand: Role of solution pH and biofilm coating

USDA-ARS?s Scientific Manuscript database

The transport, retention, and long-term fate of zinc oxide nanoparticles (ZnO-NPs) were investigated in saturated, bare and biofilm (Pseudomonas putida) coated sand packed columns. Almost complete retention of ZnO-NPs occurred in bare and biofilm coated sand when the influent solution pH was 9 and t...

Metropolitan Washington Area Water Supply Study. Appendix A. Background Information & Problem Identification.

DTIC Science & Technology

1983-09-01

area: the Patuxent, Patapsco, Magothy , and the Aquia Greensand Formations. All of these important water- bearing formations outcrop in the MWA and have...Formation - Glauconitic Silty Quartz Sand, Fine Black Magothy Formation Included at Base Nanjemoy and Wicomico Formations - Glauconitic Sand Interbedded

A Comparison of Streaming and Microelectrophoresis Methods for Obtaining the zeta Potential of Granular Porous Media Surfaces.

PubMed

Johnson

1999-01-01

The electrokinetic behavior of granular quartz sand in aqueous solution is investigated by both microelectrophoresis and streaming potential methods. zeta potentials of surfaces composed of granular quartz obtained via streaming potential methods are compared to electrophoretic mobility zeta potential values of colloid-sized quartz fragments. The zeta values generated by these alternate methods are in close agreement over a wide pH range and electrolyte concentrations spanning several orders of magnitude. Streaming measurements performed on chemically heterogeneous mixtures of physically homogeneous sand are shown to obey a simple mixing model based on the surface area-weighted average of the streaming potentials associated with the individual end members. These experimental results support the applicability of the streaming potential method as a means of determining the zeta potential of granular porous media surfaces. Copyright 1999 Academic Press.

Experimental hypervelocity impact into quartz sand - Distribution and shock metamorphism of ejecta

NASA Technical Reports Server (NTRS)

Stoeffler, D.; Gault, D. E.; Wedekind, J.; Polkowski, G.

1975-01-01

Results are presented for vertical impacts of 0.3-g cylindrical plastic projectiles into noncohesive quartz sand in which vertical and horizontal reference strate were employed by using layers of colored sand. The impacts were performed at velocities of 5.9-6.9 km/sec with a vertical gun ballistic range. The craters, 30-33 cm in diameter, reveal a radial decay of the ejecta mass per unit area with a power of -2.8 to -3.5. Material displaced from the upper 15% of the crater depth d is represented within the whole ejecta blanked, material from deeper than 28% of d is deposited inside 2 crater radii, and no material from deeper than 33% of d was ejected beyond the crater rim. Shock-metamorphosed particles (glassy agglutinates, cataclastic breccias, and comminuted quartz) amount to some 4% of the total displaced mass and indicate progressive zones of decay of shock intensity from a peak pressure of 300 kbar. The shock-metamorphosed particles and the shock-induced change in the grain size distribution of ejected samples have close analogies to the basic characteristics of the lunar regolith. Possible applications to regolith formation and to ejecta formations of large-scale impact craters are discussed.

Pb2+ and Zn2+ adsorption by a natural aluminum- and iron-bearing surface coating on an aquifer sand

USGS Publications Warehouse

Coston, J.A.; Fuller, C.C.; Davis, J.A.

1995-01-01

Pb2+ and Zn2+ adsorption was studied in batch experiments with material collected from a shallow, unconfined aquifer of glacial outwash sand and gravel in Falmouth, Massachusetts, USA. The aquifer solids contain primarily quartz with minor amounts of alkali feldspars and ferromagnetic minerals. Pb2+ and Zn2+ adsorption experiments with various grain size and mineral fractions of the aquifer solids showed that: 1) Zn2+ adsorption was independent of grain size, but Pb2+ was preferentially adsorbed by the <64 ??m size fraction and 2) Pb2+ adsorption decreased after removal of the paramagnetic, Fe-bearing mineral fraction, but Zn2+ adsorption was unaffected. Pb2+ and Zn2+ adsorption on mineral separates from the aquifer material compared with metal adsorption on a purified quartz powder indicated that adsorption of both metal ions was dominated by coatings on the quartz fraction of the sediment. Characterization of the coatings by AES, SEM-EDS, and TOF-SIMS demonstrated that the natural quartz grains were extensively coated with Al- and Fe-bearing minerals of variable composition. -from Authors

Interaction between carboxyl-functionalized carbon black nanoparticles and porous media

NASA Astrophysics Data System (ADS)

Kim, Song-Bae; Kang, Jin-Kyu; Yi, In-Geol

2015-04-01

Carbon nanomaterials, such as carbon nanotubes, fullerene, and graphene, have received considerable attention due to their unique physical and chemical characteristics, leading to mass production and widespread application in industrial, commercial, and environmental fields. During their life cycle from production to disposal, however, carbon nanomaterials are inevitably released into water and soil environments, which have resulted in concern about their health and environmental impacts. Carbon black is a nano-sized amorphous carbon powder that typically contains 90-99% elemental carbon. It can be produced from incomplete combustion of hydrocarbons in petroleum and coal. Carbon black is widely used in chemical and industrial products or applications such as ink pigments, coating plastics, the rubber industry, and composite reinforcements. Even though carbon black is strongly hydrophobic and tends to aggregate in water, it can be dispersed in aqueous media through surface functionalization or surfactant use. The aim of this study was therefore to investigate the transport behavior of carboxyl-functionalized carbon black nanoparticles (CBNPs) in porous media. Column experiments were performed for potassium chloride (KCl), a conservative tracer, and CBNPs under saturated flow conditions. Column experiments was conducted in duplicate using quartz sand, iron oxide-coated sand (IOCS), and aluminum oxide-coated sand (AOCS) to examine the effect of metal (Fe, Al) oxide presence on the transport of CBNPs. Breakthrough curves (BTCs) of CBNPs and chloride were obtained by monitoring effluent, and then mass recovery was quantified from these curves. Additionally, interaction energy profiles for CBNP-porous media were calculated using DLVO theory for sphere-plate geometry. The BTCs of chloride had relative peak concentrations ranging from 0.895 to 0.990. Transport parameters (pore-water velocity v, hydrodynamic dispersion coefficient D) obtained by the model fit from the tracer BTCs were 0.274±0.007 cm min-1 and 0.102±0.025 cm2 min-1, respectively. Mass recoveries of chloride were in the range of 94.7 to 101.9%, indicating that chloride behaved as a conservative tracer and that the column experiments were successful. The BTCs of CBNPs had different relative peak concentrations depending on the porous media used in the experiments. In quartz sand, the relative peak concentration was 0.768±0.005. The mass recovery of CBNPs in quartz sand was 83.1±2.7%, whereas no breakthrough of CBNPs (mass recovery = 0 %) was observed in IOCS or AOCS at the same flow rate, indicating that all CBNPs were retained in the IOCS and AOCS columns under the experimental conditions. These results indicate that metal (Fe, Al) oxides can play a significant role in the attachment of CBNPs to porous media. For the given solution conditions, both CBNPs and quartz sand were negatively charged with zeta potentials of -31.8±0.1 and -39.0±0.6 mV, respectively. Therefore, the electrostatic interactions between CBNPs and quartz sand were repulsive. Meanwhile, both IOCS and ACOS were positively charged with zeta potentials of 10.1±1.3 and 39.9±1.9 mV, respectively, such that the interaction between CBNPs and metal oxide-coated sands was electrostatically attractive, resulting in enhancement of CBNP attachment to the coated sands. Interaction energy profiles for CBNP-porous media were calculated using DLVO theory for sphere-plate geometry. Interaction energy profiles demonstrated that the interaction energy for CBNP-quartz sand was repulsive with a primary maximum (energy barrier) of 63.2 KBT, whereas the interaction energies for CBNP-IOCS and CBNP-AOCS were attractive with no energy barriers. Acknowledgement This research was supported by the National Institute of Environmental Research, Korea Ministry of Environment, in 2014.

Injection of polyelectrolytes enhances mobility of zero-valent iron nanoparticles in carbonate-rich porous media

NASA Astrophysics Data System (ADS)

Laumann, Susanne; Micić, Vesna; Schmid, Doris; Hofmann, Thilo

2013-04-01

The application of nanoscale zero-valent iron (nZVI) for in situ groundwater remediation has received increased attention as a beneficial and novel remediation technique. A precondition for effective nZVI field applications is its delivery to the contaminated source zones. This has proved to be difficult due to the limited mobility of nZVI, which remains one major obstacle to widespread utilization of this remediation approach (O'CAROLL ET AL., 2012). One important factor that controls mobility of nZVI is physical and chemical heterogeneity within the subsurface, such as mineralogical variations (KIM ET AL., 2012). In our previous study we showed that the nZVI transport in carbonate-rich porous media is significantly reduced compared to that in quartz porous media (LAUMANN ET AL., 2012). This is caused by favorable nZVI deposition onto carbonate sand and is attributed to the less negative surface charge of carbonate compared to that of quartz sand under the range of water chemical conditions typically encountered in aquifers. New strategies are therefore required to improve nZVI mobility in carbonate-rich porous media. One approach can be the injection of polyelectrolytes in the subsurface, which are expected to adsorb onto aquifer grains and provide greater repulsion between nZVI and the porous media. In this study the effect of co-injected polyelectrolytes on the transport of polyacrylic acid (PAA) coated nZVI in two model porous media, quartz and carbonate sands was evaluated. Column experiments were carried out aiming to evaluate mobility of PAA-nZVI co-injected with four polyelectrolytes, including natural organic matter (NOM), humic acid, carboxymethyl cellulose (CMC), and lignin sulfonate. The results demonstrated that the co-injection of the chosen polyelectrolytes does not influence mobility of PAA-nZVI in quartz sand; the breakthrough with co-injected polyelectrolytes was similar to that of the pure PAA-nZVI dispersion. This observation can be explained by the strong negative surface charge of the quartz sand, which was apparently not changed in the presence of polyelectrolytes. Conversely, the co-injected polyelectrolytes affected the breakthrough in carbonate sand, increasing nZVI mobility for approximately 15%. This can be explained by the attachment of the polyelectrolytes to the less negatively charged carbonate sand, which then promoted the PAA-nZVI mobility. Even though there are structural differences among the polyelectrolytes applied in this study, our results showed no significant variations in the PAA-nZVI mobility when these polyelectrolytes are present at concentration of 50 mg L-1. Lignin sulfonate was furthermore selected to investigate the effect of different polyelectrolyte concentrations (0, 10, 25, 50, 250, and 500 mg L-1) on the PAA-nZVI mobility. The results showed that higher lignin sulfonate concentrations (250 and 500 mg L-1) do not affect the transport of PAA-nZVI in quartz sand. In carbonate sand, on contrary, increasing mobility due to co-injected lignin sulfonate was observed at concentrations above 25 mg L-1, having the highest value with 500 mg L-1 co-injected with the PAA-nZVI dispersion. Overall, the results demonstrated that lignin sulfonate adsorption onto the carbonate sand reduce PAA-nZVI deposition onto aquifer grains and promote its mobility, the effect which is more pronounced at higher polyelectrolyte concentrations co-injected with the PAA-nZVI dispersion. The project is funded by the Federal Ministry of Agriculture, Forestry, Environment and Water Management (BMLFUW). Management by Kommunalkredit Public Consulting GmbH. Literature O'CAROLL, D. ET AL., (2012): Advances in Water Resources, in press. KIM, H.-J. ET AL., (2012): Journal of Colloid and Interface Science 370, 1-10. LAUMANN, S. ET AL., (2012): Environmental Pollution, submitted.

Mineral resource of the month: industrial sand and gravel

USGS Publications Warehouse

Dolley, Thomas

2007-01-01

With many diverse uses, industrial sand and gravel, also known as silica sand, is one of the most important nonmetallic minerals in the world. Industrial sand and gravel is a mining industry term used for sands that have a very high percentage of silicon dioxide, or greater than 95 percent quartz. Deposits of industrial sand and gravel can be found virtually everywhere on Earth, but are less widespread than deposits of common construction sand and gravel. Industrial sand and gravel is distinctive in grain size, hardness, inertness and resistance to high temperature and chemical action. Beverage containers, fiberglass insulation, fiber-optic cables and light bulbs are just some of today’s many products produced from industrial sand and gravel.

Influence Of Carboxymethyl Cellulose For The Transport Of Titanium Dioxide Nanoparticles In Clean Silica And Mineral-Coated Sands

EPA Science Inventory

The transport properties of titanium dioxide (anatase polymorph) nanoparticles encapsulated by carboxymethyl cellulose (CMC) were evaluated as a function of changes in the solute chemical properties in clean quartz, amorphous aluminum and iron hydroxide-coated sands. While prist...

Sensitivity of Geoelectrical Measurements to the Presence of Bacteria in Porous Media

EPA Science Inventory

We investigated the sensitivity of low frequency electrical measurements (0.1-1000 Hz) to (i) microbial cell density, (ii) live and dead cells, and (iii) microbial attachment onto mineral surfaces of clean quartz sands and iron oxide coated sands. Three strains of Pseudomonas aer...

Tales from a distant swamp: Petrological and paleobotanical clues for the origin of the sand coal lithotype (Mississippian, Valley Fields, Virginia)

USGS Publications Warehouse

Hower, J.C.; O'Keefe, J.M.K.; Eble, C.F.

2008-01-01

Tournasian (Mississippian) Price Formation semianthracites (Rmax = 2.40%) in the Valley Fields of southwestern Virginia contain a lithotype described in an early-20th-century report as a "sand" coal. The Center for Applied Energy Research inherited a collection of coals containing sand coal specimens, making it possible to study the lithotype from the long-closed mines. The sand coal consists of rounded quartz sand and maceral assemblages (secretinite, corpogelinite, and rounded collotelinite) along with banded collotelinite, vitrodetrinite, and inertodetrinite assemblages. The association of rounded macerals and similar-size quartz grains suggests transport. Oxidation rims surrounding the rounded collotelinite provides further evidence for transport. Due to the semianthracite rank, palynology could not be performed. Stratigraphic evidence indicates that the Lepidodendropsis flora would have been the dominant mire vegetation. Pteridosperms in this assemblage could have contributed resin rodlets, subsequently metamorphosed to collogelinite or secretinite. While a resin rodlet origin is an intriguing possibility for the origin of the rounded macerals (at least some of the rounded maceral, the rounded collotelinite clearly has a different origin), we cannot definitively prove this origin. ?? 2008 Elsevier B.V. All rights reserved.

Nitrate-cancrinite precipitation on quartz sand in simulated Hanford tank solutions.

PubMed

Bickmore, B R; Nagy, K L; Young, J S; Drexler, J W

2001-11-15

Caustic NaNO3 solutions containing dissolved Al were reacted with quartz sand at 89 degrees C to simulate possible reactions between leaked nuclear waste and primary subsurface minerals at the U.S. Department of Energy's Hanford site in Washington. Nitrate-cancrinite began to precipitate onto the quartz after 2-10 days, cementing the grains together. Estimates of the equilibrium constant for the precipitation reaction differ for solutions with 0.1 or 1.0 m OH- (log Keq = 30.4 +/- 0.8 and 36.2 +/- 0.6, respectively). The difference in solubility may be attributable to more perfect crystallinity (i.e., fewer stacking faults) in the higher-pH cancrinite structure. This is supported by electron micrographs of crystal morphology and measured rates of Na volatilization under an electron beam. Precipitate crystallinity may affect radionuclide mobility, because stacking faults in the cancrinite structure can diminish its zeolitic cation exchange properties. The precipitation rate near the onset of nucleation depends on the total Al and Si concentrations in solution. The evolution of experimental Si concentrations was modeled by considering the dependence of quartz dissolution rate on AI(OH)4- activity, cancrinite precipitation, and the reduction of reactive surface area of quartz due to coverage by cancrinite.

Luminescence of quartz and feldspar fingerprints provenance and correlates with the source area denudation in the Amazon River basin

NASA Astrophysics Data System (ADS)

Sawakuchi, A. O.; Jain, M.; Mineli, T. D.; Nogueira, L.; Bertassoli, D. J.; Häggi, C.; Sawakuchi, H. O.; Pupim, F. N.; Grohmann, C. H.; Chiessi, C. M.; Zabel, M.; Mulitza, S.; Mazoca, C. E. M.; Cunha, D. F.

2018-06-01

The Amazon region hosts the world's largest watershed spanning from high elevation Andean terrains to lowland cratonic shield areas in tropical South America. This study explores variations in optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL) signals in suspended silt and riverbed sands retrieved from major Amazon rivers. These rivers drain Pre-Cambrian to Cenozoic source rocks in areas with contrasting denudation rates. In contrast to the previous studies, we do not observe an increase in the OSL sensitivity of quartz with transport distance; for example, Tapajós and Xingu Rivers show more sensitive quartz than Solimões and Madeira Rivers, even though the latter have a significantly larger catchment area and longer sediment transport distance. Interestingly, high sensitivity quartz is observed in rivers draining relatively stable Central Brazil and Guiana shield areas (denudation rate ξ = 0.04 mmyr-1), while low sensitivity quartz occurs in less stable Andean terrains (ξ = 0.24 mmyr-1). An apparent linear correlation between quartz OSL sensitivity and denudation rate suggests that OSL sensitivity may be used as a proxy for erosion rates in the Amazon basin. Furthermore, luminescence sensitivity measured in sand or silt arises from the same mineral components (quartz and feldspar) and clearly discriminates between Andean and shield sediments, avoiding the grain size bias in provenance analysis. These results have implications for using luminescence sensitivity as a proxy for Andean and shield contributions in the stratigraphic record, providing a new tool to reconstruct past drainage configurations within the Amazon basin.

Graphene Oxide Affects Mobility and Antibacterial Ability of Levofloxacin and Ciprofloxacin in Saturated and Unsaturated Porous Media

NASA Astrophysics Data System (ADS)

Kaixuan, S.

2017-12-01

Understand the fate and impact of fluoroquinolone antibiotics (FQs) in soil and groundwater systems is critical to the safety of ecosystem and public health. In this work, laboratory batch sorption, column transport, and bacterial growth experiments were conducted to improve current understanding of the interactions between two typical FQs (levofloxacin (LEV) and ciprofloxacin (CIP)) and graphene oxide (GO) in quartz sand media under various conditions. Studies showed that both GO and quartz sand adsorbed LEV and CIP in aqueous solutions and sand was capable to compete with GO for the antibiotics. While GO showed much larger sorption capacity, the sand had stronger sorption affinity to the two antibiotics. As a result, neither LEV nor CIP showed any signs of breakthrough in saturated or unsaturated porous media. When the two antibiotics were premixed with GO, their mobility in porous media increased for both saturate and unsaturated conditions and the amount of LEV or CIP in the effluents increased with the increasing of initial GO concentration. During their transport in saturated porous media, some of the GO-bound antibiotics, especially those sorbed via relatively weak interactions, transferred from GO to the quartz sand. Under unsaturated conditions, GO-bound LEV might also transfer from GO to the air-water interface due to the strong affiliation between LEV and air-water interface. Sorption onto GO reduced the antibacterial ability of LEV and CIP, however, the GO-bound antibiotics still effectively inhibited the growth of E coli. Findings from this work indicated that mobile GO affected not only the mobility but also the ecotoxicity of LEV and CIP in porous media.

Do goethite surfaces really control the transport and retention of multi-walled carbon nanotubes in chemically heterogeneous porous media?

USDA-ARS?s Scientific Manuscript database

Transport and retention behavior of multiwalled carbon nanotubes (MWCNTs) was studied in mixtures of negatively charged quartz sand (QS) and positively charged goethite-coated sand (GQS) to assess the role of chemical heterogeneity. The linear equilibrium sorption model provided a good description o...

Transport, retention, and long-term release behavior of polymer-coated silver nanoparticles in saturated quartz sand: The impact of natural organic matters and electrolyte.

PubMed

Hou, Jun; Zhang, Mingzhi; Wang, Peifang; Wang, Chao; Miao, Lingzhan; Xu, Yi; You, Guoxiang; Lv, Bowen; Yang, Yangyang; Liu, Zhilin

2017-10-01

This study investigated the transport and long-term release of stabilized silver nanoparticles (AgNPs), including polyvinylpyrrolidone-coated AgNPs (PVP-AgNPs) and bare AgNPs (Bare-AgNPs), in the presence of natural organic matters (NOMs; both humic acids (HA) and alginate (Alg)) and an electrolyte (Ca 2+ ) in a sand-packed column. Very low breakthrough rate (C/C 0 ) of AgNPs (below 0.04) occurred in the absence of NOM and the electrolyte. Increasing the concentration of NOM and decreasing the influent NOM solution's ionic strength (IS) reduced the retention of AgNPs. The reduced NP retention at high NOM and low IS was mainly attributed to the increased energy barrier between the AgNPs and the sand grain surface. Notably, the retention of PVP-AgNPs was enhanced at high Alg concentration and low IS, which mainly resulted from the improved hydrophobicity that could increase the interaction between the PVP-AgNPs and the collector. The total release amount of PVP-AgNPs (10.03%, 9.50%, 28.42%, 6.37%) and Bare-AgNPs (3.28%, 2.58%, 10.36%, 1.54%) were gained when exposed to four kinds of NOM solutions, including deionized water, an electrolyte solution (1 mM Ca 2+ ), HA with an electrolyte (1 mM Ca 2+ ), and a Alg (40 mg/L) solution with an electrolyte (1 mM Ca 2+ ). The long-term release of retained silver nanoparticles in the quartz sand was mostly through the form of released Ag NPs. The factors that increased the mobility of AgNPs in quartz sand could improve the release of the AgNPs. The release of AgNPs had no significant change in the presence Ca 2+ but were increased in the presence of HA. The Alg slightly decreased the release of AgNPs by increasing the hydrophobicity of AgNPs. The results of the study indicated that all the tested NOM and Ca 2+ have prominent influence on the transport and long-term release behavior of silver nanoparticles in saturated quartz sand. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sedimentology and composition of sands injected during the seismic crisis of May 2012 (Emilia, Italy): clues for source layer identification and liquefaction regime

NASA Astrophysics Data System (ADS)

Fontana, D.; Lugli, S.; Marchetti Dori, S.; Caputo, R.; Stefani, M.

2015-07-01

In May 2012 widespread sand blows formed along buried channels in the eastern sector of the Po Plain (Northern Italy) as a consequence of a series of seismic events with main shocks of Mw 6.1 and 5.9. At San Carlo (Ferrara) a trench dug a few week after the earthquakes exposed sand dikes cutting through an old Reno River channel-levee system that was diverted in the 18th century and was deposited starting from the 14th century (unit A). This sequence overlies a Holocene muddy floodplain deposits and contains scattered sandy channel deposits (unit B) and a Pleistocene channel sand unit (unit C). Sands with inverse and normal grading, concave layering and vertical lamination coexisting along the dikes suggest multiple rhythmic opening and closing of the fractures that were injected and filled by a slurry of sand during the compression pulses, and emptied during the extension phase. The pulse mechanism may have lasted for several minutes and formed well stratified sand volcanoes structures that formed at the top of the fractures. Sands from dikes and from the various units show well defined compositional fields from lithoarenitic to quartz-feldspar-rich compositions. Sands from the old Reno levee and channel fill (unit A) have abundant lithic fragments derived from the erosion of Apennine sedimentary carbonate and terrigenous successions. Composition of the sand filling the dikes show clear affinities with sand layers of the old Reno River channel (Unit A) and clearly differ from any sand from deeper Holocene and Pleistocene layers (Unit B and C), which are richer in quartz and feldspar and poorer in sedimentary lithic fragments. Sorting related to sediment flux variations did not apparently affect the sand composition across the sedimentary structures. Textural and compositional data indicate that the liquefaction processes originated from a relatively shallow source consisting of channel sands located within Unit A at 6.8.to 7.5 m depth.

Influence of humic acid concentration on nTiO2 attachment to quartz sand and Fe-coated quartz sand

NASA Astrophysics Data System (ADS)

Cheng, T.; Wu, Y.

2016-12-01

The transport of nano-scale or micro-scale titanium dioxide particles (nTiO2) in subsurface environments are strongly influenced by nTiO2 attachment to sediment grains. The objective of this study is to investigate the role of humic acid (HA) in the attachment of nTiO2 to sand at low HA concentrations that are relevant to typical groundwater conditions, so that mechanisms that control nTiO2 immobilization and transport in groundwater can be elucidated. nTiO2 may carry either positive or negative charges in natural water, therefore, environmental factors such as pH, humic substances, and Fe oxyhydroxide coatings on sediment grains, which are known to control the transport of negatively-charged colloids, may influence nTiO2 in different manners. Attachment of nTiO2 to quartz sand and Fe oxyhydroxide coated quartz sand are experimentally measured under a range of HA concentrations at fixed pH. Experimental results show that at pH 5, negatively-charged HA strongly adsorbs to positively-charged nTiO2 and Fe oxyhydroxide, which, at low HA concentrations, partially neutralizes the positive charges on nTiO2 and Fe oxyhydroxide, and therefore decreases the repulsive electrostatic forces between the surfaces, resulting in relatively high nTiO2 attachment. At high HA concentrations, adsorbed HA reverses the surface charges of nTiO2 and Fe oxyhydroxide, and makes nTiO2 and Fe oxyhydroxide strongly negatively charged, resulting in low nTiO2 attachment. At pH 9, HA, nTiO2, and Fe oxyhydroxide are all negatively charged, and HA adsorption is low and does not have a strong impact on the attachment of nTiO2. This study demonstrates that the changes in surface charges of nTiO2 and Fe oxyhydroxide coating caused by HA adsorption could be a key factor that controls the attachment of nTiO2 to sediment grains.

Characterization of dissolved organic matter during reactive transport: A column experiment with spectroscopic detection

NASA Astrophysics Data System (ADS)

Vazquez, A.; Hernández, S.; Rasmussen, C.; Chorover, J.

2010-12-01

Al and Fe oxy-hydroxide minerals have been implicated in dissolved organic matter (DOM) stabilization. DOM solutions from a Pinus ponderosa forest floor (PPDOM) were used to irrigate polypropylene columns, 3.2 cm long by 0.9 cm diameter (total volume 2.0 cm3), that were packed with quartz sand (QS), gibbsite-quartz sand (Al-QS), and goethite-quartz sand (Fe-QS) mixtures. To investigate the mobilization and fractionation of DOM during reactive transport, effluent solutions were characterized by UV-Vis absorbance and excitation-emission matrix (EEM) fluorescence spectroscopies. Magnitude of PPDOM sorption followed the trend Al-QS > Fe-QS > QS during the initial transport. Effluent pH values suggest that ligand exchange is a primary mechanism for PPDOM sorption onto oxy-hydroxide minerals. Low molar absorptivity values were observed in effluent solutions of early pore volumes, indicating preferential mobilization of compounds with low aromatic character. Compounds traditionally characterized by EEM spectroscopy as being more highly humified were favorably absorbed onto the gibbsite and goethite surfaces. Humification index values (HIX) were also correlated with DOM aromaticity. HIX results suggest that the presence of low mass fractions of oxy-hydroxide minerals affect the preferential uptake of high molar mass constituents of PPDOM during reactive transport.

Mineral resource potential map of the Savannah Roadless Area, Liberty County, Florida

USGS Publications Warehouse

Patterson, Sam H.; Schmidt, Walter; Crandall, Thomas M.

1982-01-01

The Savannah Roadless Area is underlain by sedimentary rocks having low potential for oil and gas and minerals. The low potential for oil or gas notwithstanding, the possibilities for discovery cannot be ruled out because the area and nearby lands have not been thoroughly explored. No minerals have been mined within the Savannah Roadless Area, and the only production nearby has been the digging of clayey sand used in stabilizing U.S. Forest Service roads. Fuller's earth, quartz sand and gravel, clayey sand, and common clay presently are produced elsewhere in the region, and limestone and peat have been produced in the past. No clay suitable for structural clay products or fuller's earth is present in the roadless area; however, a bed of quartz sand and gravel of excellent quality was penetrated at a depth interval of 37-50 ft by one drill hole. Although this bed is coarser grained-and therefore is more suitable for many uses-than the sand deposits worked elsewhere in the Big Bend region, its mineral resource potential is reduced by the thickness of overburden above it and by its distance from markets in population centers. The Apalachicola National Forest has been explored for phosphate and reconnoitered for heavy minerals, but no valuable deposits of either have been found.

Quartz cement in sandstones: a review

NASA Astrophysics Data System (ADS)

McBride, Earle F.

Quartz cement as syntaxial overgrowths is one of the two most abundant cements in sandstones. The main factors that control the amount of quartz cement in sandstones are: framework composition; residence time in the "silica mobility window"; and fluid composition, flow volume and pathways. Thus, the type of sedimentary basin in which a sand was deposited strongly controls the cementation process. Sandstones of rift basins (arkoses) and collision-margin basins (litharenites) generally have only a few percent quartz cement; quartzarenites and other quartzose sandstones of intracratonic, foreland and passive-margin basins have the most quartz cement. Clay and other mineral coatings on detrital quartz grains and entrapment of hydrocarbons in pores retard or prevent cementation by quartz, whereas extremely permeable sands that serve as major fluid conduits tend to sequester the greatest amounts of quartz cement. In rapidly subsiding basins, like the Gulf Coast and North Sea basins, most quartz cement is precipitated by cooling, ascending formation water at burial depths of several kilometers where temperatures range from 60° to 100° C. Cementation proceeds over millions of years, often under changing fluid compositions and temperatures. Sandstones with more than 10% imported quartz cement pose special problems of fluid flux and silica transport. If silica is transported entirely as H 4SiO 4, convective recycling of formation water seems to be essential to explain the volume of cement present in most sandstones. Precipitation from single-cycle, upward-migrating formation water is adequate to provide the volume of cement only if significant volumes of silica are transported in unidentified complexes. Modeling suggests that quartz cementation of sandstones in intracratonic basins is effected by advecting meteoric water, although independent petrographic, isotopic or fluid inclusion data are lacking. Silica for quartz cement comes from both shale and sandstone beds within the depositional basin, including possibly deeply buried rocks undergoing low-grade metamorphism, but the relative importance of potential sources remains controversial and likely differs for different formations. The most likely important silica sources within unmetamorphosed shales include clay transformation (chiefly illitization of smectite), dissolution/pressure solution of detrital grains, and dissolution of opal skeletal grains; the most likely important sources of silica within unmetamorphosed sandstones include pressure solution of detrital quartz grains at grain contacts and at stylolites, feldspar alteration/dissolution, and perhaps carbonate replacement of silicate minerals and the margins of some quartz grains. Silica released by pressure solution in many sandstones post-dates the episode of cementation by quartz; thus, this silica must migrate and cement shallower sandstones in the basin or escape altogether. Some quartz-cemented sandstones are separated vertically from potential silica source beds by a kilometer or more, requiring silica transport over long distances. The similarity of diagenetic sequences in sandstones of different composition and ages apparently is the result of the normal temperature and time-dependent maturation of sediments, organic matter and pore fluids during burial in sedimentary basins. Silica that forms overgrowths is released by one or more diagenetic processes that apparently are controlled by temperature and time. Most cementation by quartz takes place when sandstone beds were in the silica mobility window specific to a particular sedimentary basin. Important secondary controls are introduced by compartmentalized domains produced by faults (e.g., North Sea) or overpressure boundaries (e.g., Gulf Coast Tertiary). Shallow meteoric water precipitates only small amounts of silica cement (generally less than 5% in most fluvial and colian sandstones), except in certain soils and at water tables in high-flux sand aquifers. Soil silcretes are chiefly cemented by opal and microcrystalline quartz, whereas water-table silcretes have abundant normal syntaxial quartz overgrowths. Silica for silcrete cements and replacements comes from quartz, silicate minerals, and locally volcanic glass, in alluvium and bedrock.

Effect of Dissolved NaC1 on Freezing Curves of Kaolinite, Montmorillonite, and Sand Pastes,

DTIC Science & Technology

1999-01-01

test this procedure. Pastes of kaolinite clay, montmorillonite , and quartz sand were prepared by washing repeatedly with aque- ous solutions of 0.1...Cold Regions Research & Engineering Laboratory Effect of Dissolved NaCI on Freezing Curves of Kaolinite , Montmorillonite , and Sand Pastes S.A...of kaolinite pastes warmed from -66.6°C to 0°C 8 4. Unfrozen-water contents, as measured by pulsed NMR, of montmorillonite pastes cooled from 0

Facilitated transport of Cu with hydroxyapatite nanoparticles in saturated sand: Effects of solution ionic strength and composition

USDA-ARS?s Scientific Manuscript database

Column experiments were conducted to investigate the facilitated transport of Cu in association with hydroxyapatite nanoparticles (nHAP) in water-saturated quartz sand at different solution concentrations of NaCl (0 to 100 mM) or CaCl2 (0.1 to 1.0 mM). The experimental breakthrough curves and retent...

Transport of biocolloids in water saturated columns packed with sand: Effect of grain size and pore water velocity

NASA Astrophysics Data System (ADS)

Syngouna, Vasiliki I.; Chrysikopoulos, Constantinos V.

2012-03-01

The main objective of this study was to evaluate the combined effects of grain size and pore water velocity on the transport in water saturated porous media of three waterborne fecal indicator organisms (Escherichia coli, MS2, and ΦX174) in laboratory-scale columns packed with clean quartz sand. Three different grain sizes and three pore water velocities were examined and the attachment behavior of Escherichia coli, MS2, and ΦX174 onto quartz sand was evaluated. The mass recoveries of the biocolloids examined were shown to be highest for Escherichia coli and lowest for MS2. However, no obvious relationships between mass recoveries and water velocity or grain size could be established from the experimental results. The observed mean dispersivity values for each sand grain size were smaller for bacteria than coliphages, but higher for MS2 than ΦX174. The single collector removal and collision efficiencies were quantified using the classical colloid filtration theory. Furthermore, theoretical collision efficiencies were estimated only for E. coli by the Interaction-Force-Boundary-Layer, and Maxwell approximations. Better agreement between the experimental and Maxwell theoretical collision efficiencies were observed.

Transport of biocolloids in water saturated columns packed with sand: Effect of grain size and pore water velocity

NASA Astrophysics Data System (ADS)

Syngouna, Vasiliki I.; Chrysikopoulos, Constantinos V.

2011-11-01

The main objective of this study was to evaluate the combined effects of grain size and pore water velocity on the transport in water saturated porous media of three waterborne fecal indicator organisms ( Escherichia coli, MS2, and ΦX174) in laboratory-scale columns packed with clean quartz sand. Three different grain sizes and three pore water velocities were examined and the attachment behavior of Escherichia coli, MS2, and ΦX174 onto quartz sand was evaluated. The mass recoveries of the biocolloids examined were shown to be highest for Escherichia coli and lowest for MS2. However, no obvious relationships between mass recoveries and water velocity or grain size could be established from the experimental results. The observed mean dispersivity values for each sand grain size were smaller for bacteria than coliphages, but higher for MS2 than ΦX174. The single collector removal and collision efficiencies were quantified using the classical colloid filtration theory. Furthermore, theoretical collision efficiencies were estimated only for E. coli by the Interaction-Force-Boundary-Layer, and Maxwell approximations. Better agreement between the experimental and Maxwell theoretical collision efficiencies were observed.

Sequence-stratigraphic controls on sandstone diagenesis: An example from the Williams Fork formation, Piceance Basin, Colorado

NASA Astrophysics Data System (ADS)

Aboktef, Adel

This study documents the distribution of diagenetic alterations in Williams Fork fluvial sandstones, assess sequence stratigraphic controls on diagenetic features, and addresses diagenetic impacts on porosity. Petrographic point counts of 220 thin sections from six wells forms the database. The near absence of potassium feldspar and volcanic rock fragments in the lower Williams Fork interval and increasing plagioclase content upward represent changes in sediment provenance rather than stratigraphic variability in diagenesis. The lower Williams Fork sands are from sedimentary sources whereas middle and upper Williams Fork sands include input from magmatic arcs and basement uplifts. Compaction, early and late cementation, dissolution, and replacement by calcite or clay minerals combined to alter Williams Fork sandstones. Infiltration of clays occurred prior to any burial. Chlorite, quartz, non-ferroan calcite, compaction and dissolution features, and kaolinite formed during eo-diagenesis at <70°C. More quartz, compaction and dissolution features, plus albite, illite, mixed-layer illite/smectite, ferroan calcite, and dolomite formed in the meso-diagenetic realm (>70°C). Four of these features show spatial variability with respect to systems tracts. Infiltrated clays are concentrated in lowstand systems tracts (LST) and highstand systems tracts (HST) because accommodation space rose slow or fell during deposition of those sands, which led to prolonged sand body exposure on floodplain and ample opportunities for downward percolation of mud during flood events. Concentration of pseudomatrix (mud intraclasts) in HST and LST deposits resulted from floodplain erosion when base-level fell with decreasing accommodation space. Authigenic chlorite formed in the HST and transgressive systems tracts (TST) of the upper half of the Williams Fork Formation because volcanic clasts are abundant in that interval. Quartz overgrowths are more likely to exceed 7% in TST deposits for reasons that are unknown. High total clay content (infiltrated, grain coatings, pseudomatrix) does inhibit quartz overgrowths in all systems tracts. Williams Fork sandstones form low-permeability tight-gas reservoirs. Primary porosity was almost entirely destroyed by compaction and cementation. Reservoir rock resulted from one of two pathways. Eogenetic authigenic chlorite and/or calcite inhibited quartz cementation, minimized compaction and protected some primary porosity. Alternately, dissolution of framework grains or cements created secondary porosity. The later pathway tends to be the more dominant.

Paragenesis and reservoir quality within a shallow combination trap: Central West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bell, D.A.; Siegrist, H.G. Jr.; Buurman, J.D.

1993-12-01

Sandstone character and reservoir quality of the Lower Mississippian Pocono Big Injun sandstone were examined in Granny Creek-Stockly field, Clay County, West Virginia. Sixty-three samples from 6 wells were analyzed using transmitted light, x-ray diffraction, and scanning electron microscopy techniques. The Pocono Big Injun formation is divided into four [open quotes]sands[close quotes] (Injun 1 through 4) based on composition and hydrocarbon productivity. The Injun 1 sand is a fine-grained, carbonate-cemented litharenite below the oil-producing zone. The oil-productive Injun 2 and 3 sands are well sorted, fine-grained litharenites which contain more authigenic and allogenic clay minerals than adjacent sands. These sandsmore » have produced more than 3.4 million bbl of oil from the Granny Creek part of the field since 1925. The Injun 4 sand is generally a coarse-grained sublitharenite with marginal gas production limited to the uppermost section of the sand. The paragenetic sequence consists of (1) minor quartz overgrowths, (2) illite and chlorite grain coatings, (3) quartz overgrowths, (4) early carbonate, (5) kaolinite, (6) calcite, (7) dolomite, and (8) pyrite. Porosity and permeability were not preserved once paragenesis progressed past the kaolinite stage. Porosity and permeability are variably preserved when steps in the paragenetic sequence are absent within the Pocono Group. Where any porosity is identified within the Pocono sandstones, primary porosity is dominant. However, secondary porosity and microporosity in clay-rich intervals are also important.« less

Transport and retention of engineered Al2O3, TiO2, and SiO2 nanoparticles through various sedimentary rocks.

PubMed

Bayat, Ali Esfandyari; Junin, Radzuan; Shamshirband, Shahaboddin; Chong, Wen Tong

2015-09-16

Engineered aluminum oxide (Al2O3), titanium dioxide (TiO2), and silicon dioxide (SiO2) nanoparticles (NPs) are utilized in a broad range of applications; causing noticeable quantities of these materials to be released into the environment. Issues of how and where these particles are distributed into the subsurface aquatic environment remain as major challenges for those in environmental engineering. In this study, transport and retention of Al2O3, TiO2, and SiO2 NPs through various saturated porous media were investigated. Vertical columns were packed with quartz-sand, limestone, and dolomite grains. The NPs were introduced as a pulse suspended in aqueous solutions and breakthrough curves in the column outlet were generated using an ultraviolet-visible spectrophotometer. It was found that Al2O3 and TiO2 NPs are easily transported through limestone and dolomite porous media whereas NPs recoveries were achieved two times higher than those found in the quartz-sand. The highest and lowest SiO2-NPs recoveries were also achieved from the quartz-sand and limestone columns, respectively. The experimental results closely replicated the general trends predicted by the filtration and DLVO calculations. Overall, NPs mobility through a porous medium was found to be strongly dependent on NP surface charge, NP suspension stability against deposition, and porous medium surface charge and roughness.

Transport, motility, biofilm forming potential and survival of Bacillus subtilis exposed to cold temperature and freeze-thaw.

PubMed

Asadishad, Bahareh; Olsson, Adam L J; Dusane, Devendra H; Ghoshal, Subhasis; Tufenkji, Nathalie

2014-07-01

In cold climate regions, microorganisms in upper layers of soil are subject to low temperatures and repeated freeze-thaw (FT) conditions during the winter. We studied the effects of cold temperature and FT cycles on the viability and survival strategies (namely motility and biofilm formation) of the common soil bacterium and model pathogen Bacillus subtilis. We also examined the effect of FT on the transport behavior of B. subtilis at two solution ionic strengths (IS: 10 and 100 mM) in quartz sand packed columns. Finally, to study the mechanical properties of the bacteria-surface bond, a quartz crystal microbalance with dissipation monitoring (QCM-D) was used to monitor changes in bond stiffness when B. subtilis attached to a quartz substrate (model sand surface) under different environmental conditions. We observed that increasing the number of FT cycles decreased bacterial viability and that B. subtilis survived for longer time periods in higher IS solution. FT treatment decreased bacterial swimming motility and the transcription of flagellin encoding genes. Although FT exposure had no significant effect on the bacterial growth rate, it substantially decreased B. subtilis biofilm formation and correspondingly decreased the transcription of matrix production genes in higher IS solution. As demonstrated with QCM-D, the bond stiffness between B. subtilis and the quartz surface decreased after FT. Moreover, column transport studies showed higher bacterial retention onto sand grains after exposure to FT. This investigation demonstrates how temperature variations around the freezing point in upper layers of soil can influence key bacterial properties and behavior, including survival and subsequent transport. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fate and Transport of Molybdenum Disulfide Nanomaterials in Sand Columns

PubMed Central

Lanphere, Jacob D.; Luth, Corey J.; Guiney, Linda M.; Mansukhani, Nikhita D.; Hersam, Mark C.; Walker, Sharon L.

2015-01-01

Abstract Research and development of two-dimensional transition metal dichalcogenides (TMDC) (e.g., molybdenum disulfide [MoS2]) in electronic, optical, and catalytic applications has been growing rapidly. However, there is little known regarding the behavior of these particles once released into aquatic environments. Therefore, an in-depth study regarding the fate and transport of two popular types of MoS2 nanomaterials, lithiated (MoS2-Li) and Pluronic PF-87 dispersed (MoS2-PL), was conducted in saturated porous media (quartz sand) to identify which form would be least mobile in aquatic environments. The electrokinetic properties and hydrodynamic diameters of MoS2 as a function of ionic strength and pH were determined using a zeta potential analyzer and dynamic light scattering techniques. Results suggest that the stability is significantly decreased beginning at 10 and 31.6 mM KCl, for MoS2-PL and MoS2-Li, respectively. Transport study results from breakthrough curves, column dissections, and release experiments suggest that MoS2-PL exhibits a greater affinity to be irreversibly bound to quartz surfaces as compared with the MoS2-Li at a similar ionic strength. Derjaguin–Landau–Verwey–Overbeek theory was used to help explain the unique interactions between the MoS2-PL and MoS2-Li surfaces between particles and with the quartz collectors. Overall, the results suggest that the fate and transport of MoS2 is dependent on the type of MoS2 that enters the environment, where MoS2-PL will be least mobile and more likely be deposited in porous media from pluronic–quartz interactions, whereas MoS2-Li will travel greater distances and have a greater tendency to be remobilized in sand columns. PMID:25741176

Parameters estimation for reactive transport: A way to test the validity of a reactive model

NASA Astrophysics Data System (ADS)

Aggarwal, Mohit; Cheikh Anta Ndiaye, Mame; Carrayrou, Jérôme

The chemical parameters used in reactive transport models are not known accurately due to the complexity and the heterogeneous conditions of a real domain. We will present an efficient algorithm in order to estimate the chemical parameters using Monte-Carlo method. Monte-Carlo methods are very robust for the optimisation of the highly non-linear mathematical model describing reactive transport. Reactive transport of tributyltin (TBT) through natural quartz sand at seven different pHs is taken as the test case. Our algorithm will be used to estimate the chemical parameters of the sorption of TBT onto the natural quartz sand. By testing and comparing three models of surface complexation, we show that the proposed adsorption model cannot explain the experimental data.

Effect of goethite coating and humic acid on the transport of bacteriophage PRD1 in columns of saturated sand

NASA Astrophysics Data System (ADS)

Foppen, J. W. A.; Okletey, S.; Schijven, J. F.

2006-05-01

The transport of bacteriophage PRD1, a model virus, was studied in columns containing sediment mixtures of quartz sand with goethite-coated sand and using various solutions consisting of monovalent and divalent salts and humic acid (HA). Without HA and in the absence of sand, the inactivation rate of PRD1 was found to be as low as 0.014 day - 1 (at 5 ± 3 °C), but in the presence of HA it was much lower (0.0009 day - 1 ), indicating that HA helps PRD1 to survive. When the fraction of goethite in the sediment was increased, the removal of PRD1 also increased. However, in the presence of HA, C/ C0 values of PRD1 increased by as much as 5 log units, thereby almost completely eliminating the effect of addition of goethite. The sticking efficiency was not linearly dependent on the amount of goethite added to the quartz sand; this is apparently due to surface charge heterogeneity of PRD1. Our results imply that, in the presence of dissolved organic matter (DOM), viruses can be transported for long distances thanks to two effects: attachment is poor because DOM has occupied favourable sites for attachment and inactivation of virus may have decreased. This conclusion justifies making conservative assumptions about the attachment of viruses when calculating protection zones for groundwater wells.

Influence of Humic Acid on Stability and Attachment of nTiO2 Particles to Sand at Different pH

NASA Astrophysics Data System (ADS)

Cheng, T.

2015-12-01

Stability of nano-scale or micro-scale titanium dioxide particles (nTiO2) and their attachment to sediment grains have important implications to the fate and transport of nTiO2 in subsurface environments. nTiO2 may carry either positive or negative charges in natural water, therefore, environmental factors such as pH, humic substances, and Fe oxyhydroxide coatings on sediment grains, which are known to control the stability and transport of negatively charged colloids, may influence nTiO2 in different manners. The objective of this study is to investigate the effects of pH and humic acid (HA) on the stability and attachment of nTiO2 to sand, with special attention to low HA concentration ranges that are relevant to groundwater conditions. Stability and attachment of nTiO2 to quartz sand and Fe oxyhydroxide coated quartz sand were experimentally measured under a range of low HA concentrations at pH 5 and 9. Results showed that HA can either promote or hinder nTiO2 stability, depending on pH and HA concentration. We also found that HA can either enhance or reduce nTiO2 attachment to Fe oxyhydroxide coating at pH 5, depending on HA concentration. Results further showed that at pH 5, Fe oxyhydroxide coating reduced nTiO2 attachment to sand in the absence of HA but increased nTiO2 attachment in the presence of low concentration of HA. Derjaguin-Landau-Verwey-Overbeek (DLVO) theory was invoked to analyze particle-to-particle and particle-to-sand interactions in order to elucidate the roles of pH, HA, quartz, and Fe coating in nTiO2 stability and attachment. Overall, this study showed that changes in zeta potential of nTiO2 and Fe coating due to pH changes and/or HA adsorption are the key factors that influence stability and attachment of nTiO2.

Mineralogical maturity in dunefields of North America, Africa and Australia

USGS Publications Warehouse

Muhs, D.R.

2004-01-01

Studies of dunefields in central and western North America show that mineralogical maturity can provide new insights into the origin and evolution of aeolian sand bodies. Many of the world's great sand seas in Africa, Asia and Australia are quartz-dominated and thus can be considered to be mineralogically mature. The Algodones (California) and Parker (Arizona) dunes in the southwestern United States are also mature, but have inherited a high degree of mineralogical maturity from quartz-rich sedimentary rocks drained by the Colorado River. In Libya, sediments of the Zallaf sand sea, which are almost pure quartz, may have originated in a similar fashion. The Fort Morgan (Colorado) and Casper (Wyoming) dunefields in the central Great Plains of North America, and the Namib sand sea of southern Africa have an intermediate degree of mineralogical maturity because their sources are large rivers that drained both unweathered plutonic and metamorphic rocks and mature sedimentary rocks. Mojave Desert dunefields in the southwestern United States are quite immature because they are in basins adjacent to plutonic rocks that were their sources. Other dunefields in the Great Plains of North America (those in Nebraska and Texas) are more mature than any possible source sediments and therefore reflect mineralogical evolution over time. Such changes in composition can occur because of either of two opposing long-term states of the dunefield. In one state, dunes are stable for long periods of time and chemical weathering depletes feldspars and other weatherable minerals in the sediment body. In the other state, which is most likely for the Great Plains, abrasion and ballistic impacts deplete the carbonate minerals and feldspars because the dunes are active for longer periods than they are stable. ?? 2003 Elsevier B.V. All rights reserved.

Mineralogical variation in the size fractions of a Ranong kaolin, southern Thailand

NASA Astrophysics Data System (ADS)

Pisutha-Arnond, Visut; Phuvichit, Suraphol; Leepowpanth, Quanchai

A representative crude Ranong kaolin from the Thungkla-Ranong mine was separated into > 2 mm (granule), 2-1 mm (very coarse sand), 1-0.5 mm (coarse sand), 0.5-0.25 mm (medium sand), 0.25-0.125 mm (fine sand), 0.125-0.062 mm (very fine sand) and 62-28, 28-14, 17-7, 7-4, 4-2, 2-1 and < 1 μ m size fractions. Those size fractions were analyzed by X-ray powder diffractometry (XRD), differential thermal analysis (DTA), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) with attached energy dispersive X-ray spectrometer (EDX). Kaolin group minerals were differentiated by using XRD in combination with various chemical and heat treatments together with TEM, SEM and DTA. The Ranong kaolin consists predominantly of tubular halloysite, poorly crystallized kaolinite and quartz with minor amounts of mica and K-feldspars. Other trace constituents include gibbsite, tourmaline, zircon and colored impurities (i.e. extractable iron hydroxide coating on clay mineral surface). The kaolin minerals are found in all size fractions by which their contents and halloysite/kaolinite ratios increase as the particle sizes become finer. Quartz and mica are also detected in almost all size fractions. They are, however, more abundant with coarsening particle size. Gibbsite, K-feldspar and tourmaline are mainly concentrated in the fine sand to silt size fractions. Crystallinity of kaolin minerals as measured by XRD varied moderately with size. Relatively pure kaolin minerals, predominantly halloysite and kaolinite, can be obtained in the particle size below 1 or 2 μm.

Effect of ferric oxyhydroxide grain coatings on the transport of bacteriophage PRD1 and Cryptosporidium parvum oocysts in saturated porous media

USGS Publications Warehouse

Abudalo, R.A.; Bogatsu, Y.G.; Ryan, J.N.; Harvey, R.W.; Metge, D.W.; Elimelech, M.

2005-01-01

To test the effect of geochemical heterogeneity on microorganism transport in saturated porous media, we measured the removal of two microorganisms, the bacteriophage PRD1 and oocysts of the protozoan parasite Cryptosporidium parvum, in flow-through columns of quartz sand coated by different amounts of a ferric oxyhydroxide. The experiments were conducted over ranges of ferric oxyhydroxide coating fraction of ?? = 0-0.12 for PRD1 and from ?? = 0-0.32 for the oocysts at pH 5.6-5.8 and 10-4 M ionic strength. To determine the effect of pH on the transport of the oocysts, experiments were also conducted over a pH range of 5.7-10.0 at a coating fraction of ?? = 0.04. Collision (attachment) efficiencies increased as the fraction of ferric oxyhydroxide coated quartz sand increased, from ?? = 0.0071 to 0.13 over ?? = 0-0.12 for PRD1 and from ?? = 0.059 to 0.75 over ?? = 0-0.32 for the oocysts. Increasing the pH from 5.7 to 10.0 resulted in a decrease in the oocyst collision efficiency as the pH exceeded the expected point of zero charge of the ferric oxyhydroxide coatings. The collision efficiencies correlated very well with the fraction of quartz sand coated by the ferric oxyhydroxide for PRD1 but not as well for the oocysts. ?? 2005 American Chemical Society.

Sepia ink as a surrogate for colloid transport tests in porous media

NASA Astrophysics Data System (ADS)

Soto-Gómez, Diego; Pérez-Rodríguez, Paula; López-Periago, J. Eugenio; Paradelo, Marcos

2016-08-01

We examined the suitability of the ink of Sepia officinalis as a surrogate for transport studies of microorganisms and microparticles in porous media. Sepia ink is an organic pigment consisted on a suspension of eumelanin, and that has several advantages for its use as a promising material for introducing the frugal-innovation in the fields of public health and environmental research: very low cost, non-toxic, spherical shape, moderate polydispersivity, size near large viruses, non-anomalous electrokinetic behavior, low retention in the soil, and high stability. Electrokinetic determinations and transport experiments in quartz sand columns and soil columns were done with purified suspensions of sepia ink. Influence of ionic strength on the electrophoretic mobility of ink particles showed the typical behavior of polystyrene latex spheres. Breakthrough curve (BTC) and retention profile (RP) in quartz sand columns showed a depth dependent and blocking adsorption model with an increase in adsorption rates with the ionic strength. Partially saturated transport through undisturbed soil showed less retention than in quartz sand, and matrix exclusion was also observed. Quantification of ink in leachate fractions by light absorbance is direct, but quantification in the soil profile with moderate to high organic matter content was rather cumbersome. We concluded that sepia ink is a suitable cheap surrogate for exploring transport of pathogenic viruses, bacteria and particulate contaminants in groundwater, and could be used for developing frugal-innovation related with the assessment of soil and aquifer filtration function, and monitoring of water filtration systems in low-income regions.

Transport and retention of engineered Al2O3, TiO2, and SiO2 nanoparticles through various sedimentary rocks

PubMed Central

Esfandyari Bayat, Ali; Junin, Radzuan; Shamshirband, Shahaboddin; Tong Chong, Wen

2015-01-01

Engineered aluminum oxide (Al2O3), titanium dioxide (TiO2), and silicon dioxide (SiO2) nanoparticles (NPs) are utilized in a broad range of applications; causing noticeable quantities of these materials to be released into the environment. Issues of how and where these particles are distributed into the subsurface aquatic environment remain as major challenges for those in environmental engineering. In this study, transport and retention of Al2O3, TiO2, and SiO2 NPs through various saturated porous media were investigated. Vertical columns were packed with quartz-sand, limestone, and dolomite grains. The NPs were introduced as a pulse suspended in aqueous solutions and breakthrough curves in the column outlet were generated using an ultraviolet-visible spectrophotometer. It was found that Al2O3 and TiO2 NPs are easily transported through limestone and dolomite porous media whereas NPs recoveries were achieved two times higher than those found in the quartz-sand. The highest and lowest SiO2-NPs recoveries were also achieved from the quartz-sand and limestone columns, respectively. The experimental results closely replicated the general trends predicted by the filtration and DLVO calculations. Overall, NPs mobility through a porous medium was found to be strongly dependent on NP surface charge, NP suspension stability against deposition, and porous medium surface charge and roughness. PMID:26373598

Cation-Inhibited Transport of Graphene Oxide Nanomaterials in Saturated Porous Media: The Hofmeister Effects.

PubMed

Xia, Tianjiao; Qi, Yu; Liu, Jing; Qi, Zhichong; Chen, Wei; Wiesner, Mark R

2017-01-17

Transport of negatively charged nanoparticles in porous media is largely affected by cations. To date, little is known about how cations of the same valence may affect nanoparticle transport differently. We observed that the effects of cations on the transport of graphene oxide (GO) and sulfide-reduced GO (RGO) in saturated quartz sand obeyed the Hofmeister series; that is, transport-inhibition effects of alkali metal ions followed the order of Na + < K + < Cs + , and those of alkaline earth metal ions followed the order of Mg 2+ < Ca 2+ < Ba 2+ . With batch adsorption experiments and microscopic data, we verified that cations having large ionic radii (and thus being weakly hydrated) interacted with quartz sand and GO and RGO more strongly than did cations of small ionic radii. In particular, the monovalent Cs + and divalent Ca 2+ and Ba 2+ , which can form inner-sphere complexes, resulted in very significant deposition of GO and RGO via cation bridging between quartz sand and GO and RGO, and possibly via enhanced straining, due to the enhanced aggregation of GO and RGO from cation bridging. The existence of the Hofmeister effects was further corroborated with the interesting observation that cation bridging was more significant for RGO, which contained greater amounts of carboxyl and phenolic groups (i.e., metal-complexing moieties) than did GO. The findings further demonstrate that transport of nanoparticles is controlled by the complex interplay between nanoparticle surface functionalities and solution chemistry constituents.

Lidar characterization of crystalline silica generation and transport from a sand and gravel plant.

PubMed

Trzepla-Nabaglo, Krystyna; Shiraki, Ryoji; Holmén, Britt A

2006-04-30

Light detection and ranging (Lidar) remote sensing two-dimensional vertical and horizontal scans collected downwind of a sand and gravel plant were used to evaluate the generation and transport of geologic fugitive dust emitted by quarry operations. The lidar data give unsurpassed spatial resolution of the emitted dust, but lack quantitative particulate matter (PM) mass concentration data. Estimates of the airborne PM10 and crystalline silica concentrations were determined using linear relationships between point monitor PM10 and quartz content data with the lidar backscatter signal collected from the point monitor location. Lidar vertical profiles at different distances downwind from the plant were used to quantify the PM10 and quartz horizontal fluxes at 2-m vertical resolution as well as off-site emission factors. Emission factors on the order of 65-110 kg of PM10 (10-30 kg quartz) per daily truck activity or 2-4 kg/t product shipped (0.5-1 kg quartz/t) were quantified for this facility. The lidar results identify numerous elevated plumes at heights >30 m and maximum plume heights of 100 m that cannot be practically sampled by conventional point sampler arrays. The PM10 and quartz mass flux was greatest at 10-25 m height and decreased with distance from the main operation. Measures of facility activity were useful for explaining differences in mass flux and emission rates between days. The study results highlight the capabilities of lidar remote sensing for determining the spatial distribution of fugitive dust emitted by area sources with intermittent and spatially diverse dust generation rates.

[Volatile ashes and their biological effect. 2. Fibrogenic effect of volatile ashes].

PubMed

Woźniak, H; Wiecek, E; Lao, I; Wojtczak, J

1989-01-01

In experiments on white Wistar rats fibrogenic effects of 6 samples of fly-ashes collected from electric precipitators in power engineering plants have been evaluated. The coal came from different national deposits. All the ashes have been found to contain: quartz and mullite, 3 ashes contained additionally orthoclase, whereas 1, apart from quartz and mullite, contained kaolinite; naturally radioactive elements (Ra226, K40, Th228) and trace elements (As, Ba, Be, Cd, Ce, Cu, Fe, Pa, Mo, Ni, Pb, Se, U Zu). Experimental pneumoconiosis was induced through intratracheal administration of single doses of 50 mg of dust; the experiment was carried out at 3 time intervals of 3, 6 and 9 months. The fibrogenic activity was evaluated both qualitatively (histopathological methods) and quantitatively (lung weight, hydroxyproline content in lungs, dust elimination from lungs); control groups consisted of animals which obtained NaCl solution and quartz sands. Fly-ashes were found to exhibit different fibrogenic effects, yet, their fibrogenic activity was weaker, compared to quartz sands. No clear correlation was found between fibrogenic effects of ashes and test physico-chemical properties, such as the content of SiO2, trace elements or naturally radioactive elements. Analysis of occupational diseases (for the period section): (1979-1983) demonstrated occupational diseases of dust-related aetiology among power engineering workers, pneumoconioses, constituting 7.8% of 127 cases of occupational diseases.

Sediment Particle Characterization for Acoustic Applications: Coarse Content, Size and Shape Distributions in a Shelly Sand/Mud Environment

DTIC Science & Technology

2009-03-31

Distributions in a Shelly Sand/Mud Environment Anatoliy N. Ivakin M A Ivakin. Particle size and shape distributions 2 Goff et al . [3] came to a...site, 37.0=P and 65.2=sρ g /cm 3 [19], were used for calculations. The sediment volume for calculations was taken to be 1885 cm 3 for each of the...typical values used for densities of quartz (sand) particles and calcium carbonate (shell) particles were taken to be 2.65 g /cm 3 and 2.75 g /cm 3

Discrimination of active and inactive sand from remote sensing - Kelso dunes, Mojave Desert, California

NASA Technical Reports Server (NTRS)

Paisley, Elizabeth C. I.; Lancaster, Nicholas; Gaddis, Lisa R.; Greeley, Ronald

1991-01-01

Landsat TM images, field data, and laboratoray reflectance spectra were examined for the Kelso dunes, Mojave Desert, California to assess the use of visible and near-infrared (VNIR) remote sensing data to discriminate aeolian sand populations on the basis of spectral brightness. Results show that areas of inactive sand have a larger percentage of dark, fine-grained materials compared to those composed of active sand, which contain less dark fines and a higher percentage of quartz sand-size grains. Both areas are spectrally distinct in the VNIR, suggesting that VNIR spectral data can be used to discriminate active and inactive sand populations in the Mojave Desert. Analysis of laboratory spectra was complicated by the presence of magnetite in the active sands, which decreases their laboratory reflectance values to those of inactive sands. For this application, comparison of TM and laboratory spectra suggests that less than 35 percent vegetation cover does not influence the TM spectra.

Evaluating Rotavirus and Norovirus transport processes in standardised and natural soil-water columns experiments

NASA Astrophysics Data System (ADS)

Gamazo, Pablo; Schijven, Jack; Victoria, Matias; Alvareda, Elena; López Tort, Fernando; Ramos, Julián; Lizasoain, Andrés; Sapriza, Gonzalo; Castells, Matias; Colina, Rodney

2017-04-01

In Uruguay, as in many developed and developing countries, rotavirus and norovirus are major causes of diarrhea and others symptoms of acute gastroenteritis. In some areas of Uruguay, groundwater is the only source of water for human consumption. In the rural area of the Salto district, virus contamination has been detected in several groundwater wells. Because sewer coverage is low, the most probable sources of contamination are nearby septic systems. This work aims to evaluate the transport of rotavirus and norovirus from clinic samples in two sets of column experiments under saturated conditions: 6.7-cm columns with quartz sand (ionic strength 1mM, pH 7.0) and with sand from the Salto aquifer (Uruguay) (9,2% coarse sand, 47,8% medium sand, 40,5% fine sand, magnesium/calcium bicarbonate water, Ionic strength 15.1 mM, pH 7.2). Both viruses were seeded for 2 pore volumes onto the columns. Samples were collected at the column outlet and viruses were enumerated by Q-PRCR. Breakthrough curves were constructed and fitted to a two-site kinetic attachment/detachment model, including blocking using Hydrus-1D. In the quartz sand column, both rotavirus and norovirus were removed two orders in magnitude. In the Salto sand column, rotavirus was removed 2 log10 as well, but norovirus was removed 4 log10. The fitting of the breakthrough curves indicated that blocking played a role for rotavirus in the Salto sand column. These results are consistent with the field observation where only rotavirus was detected in the Salto aquifer, while similar concentrations in Salto sewer effluent were measured for both viruses. This work, besides reporting actual parameters values for human virus transport modelling, shows the significant differences in transport that human viruses can have in standardised and natural soil-water systems.

Some problems associated with the analysis and interpretation of mixed carbonate and quartz beach sands, illustrated by examples from North-West Ireland

NASA Astrophysics Data System (ADS)

Carter, R. W. G.

1982-09-01

Mixes of carbonate and quartz sands, which are commonly encountered in Recent coastal sediments, require careful analysis if they are to be correctly interpreted. Grain-size data fall into multimodal or segmented zig-zag distributions which may require some kind of component separation if they are to be summarised by conventional statistics, and before they can be assigned to a particular hydrodynamic depositional process or environment. Unfortunately, separation techniques are only spasmodically applied, usually without due regard to the consequences. Such artificially filtered or truncated distributions are of little subsequent use. Using a range of samples from two beaches in NW Ireland, where carbonate proportions range from nearly zero to over sixty percent, the interrelationships of the two dominant components were examined. Where only a small carbonate proportion is incorporated into a large quartz one, predictable modifications of the size-curve are apparent. However, the components are more independent if mixtures are near equal. The occurrence of a number of distinctive combinations of simple straight lines and complex zig-zag curves probably reflects the relatively dynamic nature of the carbonate fraction.

Characterization of desert sand as a sensible thermal energy storage medium

NASA Astrophysics Data System (ADS)

Diago, Miguel; Iniesta, Alberto Crespo; Delclos, Thomas; Soum-Glaude, Audrey; Shamim, Tariq; Calvet, Nicolas

2016-05-01

Desert sand from the United Arab Emirates (UAE) is considered as a possible sensible heat, thermal energy storage (TES) material. Its thermal stability, specific heat capacity and tendency to agglomerate are studied at high temperatures. The analyses show that it is possible to use desert sand as a TES material up to 800-1000 °C. Above 800 °C, weak agglomeration effects start to become significant. The samples become solid above 1000 °C. This may represent a major operating limit depending on the handling mechanism in place for the possible transport of the sand. The sand chemical composition is analyzed with the XRF and XRD techniques, which reveal the dominance of quartz and carbonates. Finally, the spectral absorptivity of the samples is measured before and after a thermal cycle, as it may be possible to use the desert sand not only as a TES material but also as a direct solar absorber.

Wind-driven particle mobility on Mars: Insights from Mars Exploration Rover observations at "El Dorado" and surroundings at Gusev Crater

USGS Publications Warehouse

Sullivan, R.; Arvidson, R.; Bell, J.F.; Gellert, Ralf; Golombek, M.; Greeley, R.; Herkenhoff, K.; Johnson, J.; Thompson, S.; Whelley, P.; Wray, J.

2008-01-01

The ripple field known as 'El Dorado' was a unique stop on Spirit's traverse where dust-raising, active mafic sand ripples and larger inactive coarse-grained ripples interact, illuminating several long-standing issues of Martian dust mobility, sand mobility, and the origin of transverse aeolian ridges. Strong regional wind events endured by Spirit caused perceptible migration of ripple crests in deposits SSE of El Dorado, erasure of tracks in sandy areas, and changes to dust mantling the site. Localized thermal vortices swept across El Dorado, leaving paths of reduced dust but without perceptibly damaging nearly cohesionless sandy ripple crests. From orbit, winds responsible for frequently raising clay-sized dust into the atmosphere do not seem to significantly affect dunes composed of (more easily entrained) sand-sized particles, a long-standing paradox. This disparity between dust mobilization and sand mobilization on Mars is due largely to two factors: (1) dust occurs on the surface as fragile, low-density, sand-sized aggregates that are easily entrained and disrupted, compared with clay-sized air fall particles; and (2) induration of regolith is pervasive. Light-toned bed forms investigated at Gusev are coarse-grained ripples, an interpretation we propose for many of the smallest linear, light-toned bed forms of uncertain origin seen in high-resolution orbital images across Mars. On Earth, wind can organize bimodal or poorly sorted loose sediment into coarse-grained ripples. Coarse-grained ripples could be relatively common on Mars because development of durable, well-sorted sediments analogous to terrestrial aeolian quartz sand deposits is restricted by the lack of free quartz and limited hydraulic sediment processing. Copyright 2008 by the American Geophysical Union.

Dunes Around Khnifiss Lagoon (Tarfaya, SW of Morocco): Composition, Itinerary In Dune Fields, Effects on Dunes' Colours and Morphodynamic

NASA Astrophysics Data System (ADS)

Adnani, M.; Azzaoui, M. A.; Elbelrhiti, H.; Ahmamou, M.; Masmoudi, L.

2015-12-01

Dunes around Khnifiss lagoon (28° 3'N, 12°13'W) show different colors ranging from black at the beach, whitish yellow in transverse dunes near the beach to reddish at the mega barchans situated few kilometers in the SW. The scientific question is about the abundance of different dunes in the same environmental conditions. The present work aims to investigate the factors that influence dunes color change, and then at which degree these factors could control dunes stability. To highlight the difference in color observed at the dune fields then to characterize dunes mineralogy, Landsat TM images were used in addition to mineralogical analysis that was carried out for the black grains samples originated from megabarchans. Optic Microscope and SEM- EDS data was adopted, in addition to physico-chemical analysis provided by Electronic Microprobe. Grain size and shape analysis were conducted to characterize the different types of grains of sand. 3/1 Landsat image band ratio allowed iron oxide distinction, the results revealed the importance of iron oxide concentration. Furthermore, mineralogical and physico-chemical analysis revealed (i) a high grade of oxides (Rutile, Ilmenite, Magnetite, Ulvöspinel) in samples, (ii) silicates (Quartz, Clinopyroxene, feldspar, Zircon), (iii) phosphate (apatite) and (iv) carbonate (calcite). The grain size analysis of the sand originated from the megabarchans reveals that there are three populations of sand. Black grains with a diameter less than 100μm and dominated by the magnetite, red ones composed mainly by the quartz with diameter between 100 and 180 μm and grains with diameter more than 180 μm are white and composed by carbonates. The threshold of motion of these different grains was calculated. It shows that these different grains have the same threshold of motion, which means that the grain size compensates the density. This explains the abundance of different populations of sand in the same environment. The dominance of iron oxides justified the color black in sand. However, the whitish yellow and reddish color observed in dunes could be attributed to iron oxide clay coating, produced under weathering conditions, covering the grains of quartz. Key words: black sand, Landsat, Iron Oxide, Khnifiss beach, megadunes, Tarfaya, Morocco

Reconnaissance geology of the Jabal Shaqran Quadrangle, sheet 17/44 B, Kingdom of Saudi Arabia

USGS Publications Warehouse

Sable, Edward G.

1982-01-01

The Jabal Shaqran quadrangle lies in the southeastern Asir province, mostly within the westernmost part of the Rub al Khali desert, and is largely covered by Quaternary deposits. Proterozoic crystalline rocks are exposed as inselbergs or rock pediment surfaces along the western border of the quadrangle. The crystalline basement is metavolcanic rock intruded by plutonic to hypabyssal rocks consisting of diorite and gabbro, biotite tonalite gneiss, biotite-hornblende monzogranite, biotite-sodic amphibole granite, and syenogranite to quartz syenite, listed in the inferred order of emplacement. Rhyolite-dacite fels, associated with andesitic to basaltic metavolcanic flow rocks and minor amphibolite, is interpreted to have resulted from metasomatic alteration of the flow rocks during emplacement of granitic plutons. The Wajid Sandstone, of Cambrian to Ordovician age, is largely a coarse-grained quartz arenite with pebbly phases; common crossbedds indicate north-northwest to north-northeast directions of sand transport. Beds are cemented by iron oxide, carbonate, and minor quartz. The Wajid Sandstone is exposed only in the northwestern and northern parts of the quadrangle. Quaternary deposits record a climate that became increasingly more arid. They include Holocene and Pleistocene(?) alluvial and fluvial deposits of sand, gravel, and silt, minor carbonate crusts, and eolian sand and silt. Gravel terraces and gravel plains less than 10 m above the present major wadi channels are widespread and commonly are overlain by marly silt along the wadis. Between major wadis, which discharge into the Rub al Khali basin, gravel-topped surfaces are partly covered by a complex of low, sinuous, discontinuous, generally northwest trending transverse sand dunes. Normal to this trend, higher and more extensive linear dunes and dune complexes, including seif (irq) dunes as high as 50 m, have encroached southwestward. The transverse and linear dunes may represent two stages of advance separated by a pluvial cycle. Studies of aerial photographs indicate that the dunes have not changed appreciably in shape or size between 1951 and 1959, although some seif dunes have advanced their leading edges 15 to 25 m. No potentially economic mineral resources other than sand and gravel were found.

Measurements of the Coefficient of Restitution of Quartz Sand on Basalt: Implications for Abrasion Rates on Earth and Mars

NASA Technical Reports Server (NTRS)

Banks, M.; Bridges, N. T.; Benzit, M.

2005-01-01

Knowledge of the rates at which rocks abrade from the impact of saltating sand provides important input into estimating the age and degree of modification of arid surfaces on Earth and Mars. Previous work has relied on measuring mass loss rates in the field and the laboratory. The susceptibility of rocks and other natural materials has been quantified on a relative scale from laboratory studies.

[Factors affecting biological removal of iron and manganese in groundwater].

PubMed

Xue, Gang; He, Sheng-Bing; Wang, Xin-Ze

2006-01-01

Factors affecting biological process for removing iron and manganese in groundwater were analyzed. When DO and pH in groundwater after aeration were 7.0 - 7.5 mg/L and 6.8 - 7.0 respectively, not only can the activation of Mn2+ oxidizing bacteria be maintained, but also the demand of iron and manganese removal can be satisfied. A novel inoculating approach of grafting mature filter material into filter bed, which is easier to handle than selective culture media, was employed in this research. However, this approach was only suitable to the filter material of high-quality manganese sand with strong Mn2+ adsorption capacity. For the filter material of quartz sand with weak adsorption capacity, only culturing and domesticating Mn2+ oxidizing bacteria by selective culture media can be adopted as inoculation in filter bed. The optimal backwashing rate of biological filter bed filled with manganese sand and quartz sand should be kept at a relatively low level of 6 - 9 L/(m2 x s) and 7 -11 L/( m2 x s), respectively. Then the stability of microbial phase in filter bed was not disturbed, and iron and manganese removal efficiency recovered in less than 5h. Moreover, by using filter material with uniform particle size of 1.0 - 1.2 mm in filter bed, the filtration cycle reached as long as 35 - 38h.

Application of ultrasound and quartz sand for the removal of disinfection byproducts from drinking water.

PubMed

Yang, Wu; Dong, Lili; Luo, Zhen; Cui, Xiaochun; Liu, Jiancong; Liu, Zhongmou; Huo, Mingxin

2014-04-01

To the best of our knowledge, little information is available on the combined use of ultrasound (US) and quartz sand (QS) in the removal of disinfection byproducts (DBPs) from drinking water. This study investigates the removal efficiency for 12 DBPs from drinking water by 20 kHz sonolytic treatment, QS adsorption, and their combination. Results indicate that DBPs with logKow≤1.12 could not be sonolysized; for logKow≥1.97, more than 20% removal efficiency was observed, but the removal efficiency was unrelated to logKow. DBPs containing a nitro group are more sensitive to US than those that comprise nitrile, hydrogen, and hydroxyl groups. Among the 12 investigated DBPs, 9 could be adsorbed by QS adsorption. The adsorption efficiency ranged from 12% for 1,1-dichloro-2-propanone to 80% for trichloroacetonitrile. A synergistic effect was found between the US and QS on DBPs removal, and all the 12 DBPs could be effectively removed by the combined use of US and QS. In the presence of US, part of the QS particles were corroded into small particles which play a role in increasing the number of cavitation bubbles and reducing cavitation bubble size and then improve the removal efficiency of DBPs. On the other hand, the presence of US enhances the DBP mass transfer rate to cavitation bubbles and quartz sand. In addition, sonolytic treatment led to a slight decrease of pH, and TOC values decreased under all the three treatment processes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Aeolian comminution experiments revealing surprising sandball mineral aggregates

NASA Astrophysics Data System (ADS)

Nørnberg, P.; Bak, E.; Finster, K.; Gunnlaugsson, H. P.; Iversen, J. J.; Jensen, S. Knak; Merrison, J. P.

2014-06-01

We have undertaken a set of wind erosion experiments on a simple and well defined mineral, quartz. In these experiments wind action is simulated by end over end tumbling of quartz grains in a sealed quartz flask. The tumbling induces collisions among the quartz grains and the walls of the flask. This process simulates wind action impact speed of ∼1.2 m/s. After several months of tumbling we observed the formation of a large number of spherical sand aggregates, which resemble small snowballs under optical microscopy. Upon mechanical load the aggregates are seen to be more elastic than quartz and their mechanical strength is comparable, though slightly lower than that of sintered silica aerogels. Aggregates of this kind have not been reported from field sites or from closed circulation systems. However, sparse occurrence might explain this, or in nature the concentration of the aggregate building particles is so low that they never meet and just appear as the most fine grained tail of the sediment particle size distribution.

Identification and Purification of Nyalo River Silica Sand as Raw Material for the Synthesis of Sodium Silicate

NASA Astrophysics Data System (ADS)

Aini, S.; Nizar, U. K.; NST, A. Amelia; Efendi, J.

2018-04-01

This research is on identification and purification of silica sand from Nyalo River. It will be used as a raw material for synthesis of sodium silicate. Silica sand was separated from clay by washing it with water, and then the existing alumina and iron oxide were removed by soaking the silica sand with 1 M HNO3 solution. Qualitative and quantitative analysis of the silica sand with X-ray diffraction and X-ray fluorescence revealed that, silica sand existed in quartz form and contained a small amount of impurity oxide such as Al2O3, K2O, MgO, CaO, Fe2O3 with percentage below the minimum threshold. The percentages of silica were 80.59% before purification. After three purificationsteps the silica percentage become 98.38%. It exceedsthe minimum threshold of silica percentage for industry.So, the silica sand from Nyalo River has high potency as a raw material for sodium silicate synthesizing.

Application of hydrometallurgy techniques in quartz processing and purification: a review

NASA Astrophysics Data System (ADS)

Lin, Min; Lei, Shaomin; Pei, Zhenyu; Liu, Yuanyuan; Xia, Zhangjie; Xie, Feixiang

2018-04-01

Although there have been numerous studies on separation and purification of metallic minerals by hydrometallurgy techniques, applications of the chemical techniques in separation and purification of non-metallic minerals are rarely reported. This paper reviews disparate areas of study into processing and purification of quartz (typical non-metallic ore) in an attempt to summarize current work, as well as to suggest potential for future consolidation in the field. The review encompasses chemical techniques of the quartz processing including situations, progresses, leaching mechanism, scopes of application, advantages and drawbacks of micro-bioleaching, high temperature leaching, high temperature pressure leaching and catalyzed high temperature pressure leaching. Traditional leaching techniques including micro-bioleaching and high temperature leaching are unequal to demand of modern glass industry for quality of quartz concentrate because the quartz products has to be further processed. High temperature pressure leaching and catalyzed high temperature pressure leaching provide new ways to produce high-grade quartz sand with only one process and lower acid consumption. Furthermore, the catalyzed high temperature pressure leaching realizes effective purification of quartz with extremely low acid consumption (no using HF or any fluoride). It is proposed that, by integrating the different chemical processes of quartz processing and expounding leaching mechanisms and scopes of application, the research field as a monopolized industry would benefit.

Fungal alteration of organic coatings on sand grains

NASA Astrophysics Data System (ADS)

Rothhardt, S.; Gleixner, G.; Benzerara, K.; Fischer, C.; Gaupp, R.

2012-04-01

We studied the fungal alteration of organically coated sand particles, sampled in Eocene sediments in the open cast mining Profen, near Leipzig (Germany). These organic coatings were formed on sand grains after their sedimentation owing to mobilization of organic matter from younger coal layers. The organic coatings formed non-continuous layers on quartz grains, measuring few micrometers up to 30 µm in thickness. It has been shown that organic coatings on sand grains retain efficiently dissolved metals by adsorption from groundwaters. They consequently might be used as adsorbent to purify low heavy metal contaminated water. However, their stability has not been assessed yet especially in the oxic environment and, more specifically, in the presence of microorganisms. This is important in order to evaluate whether coated sands could act as a reliable tool in remediation. In order to address this question we characterized the fungal alteration of organic coatings on sand grains using several techniques, including scanning electron microscopy (SEM), scanning transmission X-ray microscopy (STXM) and vertical scanning interferometry (VSI). Sand grains coated with organics were incubated on complex yeast medium with and without Schizophyllum commune to estimate changes in heavy metal retention. Formation of biominerals and etch pits is induced by fungal colonization as shown by SEM. Surface topography analysis was performed using VSI technique. Etch pit depth ranges from 0.5 to 1 µm. Pit formation is limited to the organic coating; dissolution of quartz grains was not detected. Using STXM we measured near-edge X-ray absorption fine structure (NEXAFS) spectra at the C K-edge, N-edge, and O K-edge to characterize the different organic compartments (fungi, genuine organic coatings, altered organic coatings) down to the 25-nm scale. We observed in the spectra measured at the C K-edge on the altered organic coatings a decrease in aromatic and phenolic groups as well as an enrichment in amide-rich molecules compared to the genuine organic coatings. Our results suggest heterogeneous biodegradation of organic coatings on sand grains by fungal exudation. An important implication might be the overall decrease in metal retention potential of organically coated sand grains owing to the alteration processes by S. commune.

Aqueous Cleaning and Validation for Space Shuttle Propulsion Hardware at the White Sands Test Facility

NASA Technical Reports Server (NTRS)

Hornung, Steven D.; Biesinger, Paul; Kirsch, Mike; Beeson, Harold; Leuders, Kathy

1999-01-01

The NASA White Sands Test Facility (WSTF) has developed an entirely aqueous final cleaning and verification process to replace the current chlorofluorocarbon (CFC) 113 based process. This process has been accepted for final cleaning and cleanliness verification of WSTF ground support equipment. The aqueous process relies on ultrapure water at 50 C (323 K) and ultrasonic agitation for removal of organic compounds and particulate. The cleanliness is verified bv determining the total organic carbon (TOC) content and filtration with particulate counting. The effectiveness of the aqueous methods for detecting hydrocarbon contamination and particulate was compared to the accepted CFC 113 sampling procedures. Testing with known contaminants, such as hydraulic fluid and cutting and lubricating oils, to establish a correlation between aqueous TOC and CFC 113 nonvolatile residue (NVR) was performed. Particulate sampling on cleaned batches of hardware that were randomly separated and sampled by the two methods was performed. This paper presents the approach and results, and discusses the issues in establishing the equivalence of aqueous sampling to CFC 113 sampling, while describing the approach for implementing aqueous techniques on Space Shuttle Propulsion hardware.

Eolian sand transport pathways in the southwestern United States: Importance of the Colorado River and local sources

USGS Publications Warehouse

Muhs, D.R.; Reynolds, R.L.; Been, J.; Skipp, G.

2003-01-01

Geomorphologists have long recognized that eolian sand transport pathways extend over long distances in desert regions. Along such pathways, sediment transport by wind can surmount topographic obstacles and cross major drainages. Recent studies have suggested that three distinct eolian sand transport pathways exist (or once existed) in the Mojave and Sonoran Desert regions of the southwestern United States. One hypothesized pathway is colian sand transport from the eastern Mojave Desert of California into western Arizona, near Parker, and would require sand movement across what must have been at least a seasonally dry Colorado River valley. We tested this hypothesis by mineralogical, geochemical and magnetic analyses of eolian sands on both sides of the Colorado River, as well as sediment from the river itself. Results indicate that dunes on opposite sides of the Colorado River are mineralogically distinct: eastern California dunes are feldspar-rich whereas western Arizona dunes are quartz-rich, derived from quartz-rich Colorado River sediments. Because of historic vegetation changes, little new sediment from the Colorado River is presently available to supply the Parker dunes. Based on this study and previous work, the Colorado River is now known to be the source of sand for at least three of the major dune fields of the Sonoran Desert of western Arizona and northern Mexico. On the other hand, locally derived alluvium appears to be a more important source of dune fields in the Mojave Desert of California. Although many geomorphologists have stressed the importance of large fluvial systems in the origin of desert dune fields, few empirical data actually exist to support this theory. The results presented here demonstrate that a major river system in the southwestern United States is a barrier to the migration of some dune fields, but essential to the origin of others. Published by Elsevier Science Ltd.

Luminescence quartz dating of lime mortars. A first research approach.

PubMed

Zacharias, N; Mauz, B; Michael, C T

2002-01-01

Lime mortars mixed with sand are well suited for connecting structural materials, like stones and bricks, due to the mechanical properties this material exhibits. Their extensive use in architectural and decorative works during the last 4000 years motivated the introduction of the 'Luminescence clock' for age determination of mortars. The same principles as for quartz optically stimulated luminescence (OSL) dating of sediments were applied for age estimation of a mortar fragment removed from a Byzantine church monument dated by archaeological means to 1050-1100 years ago (the first half of the 10th century). The OSL from the quartz was monitored under blue light stimulation and UV detection, using a single-aliquot-regenerative-dose protocol. The quartz-OSL dating of the mortar resulted in 870 +/- 230 a. TL polymineral fine grain dating was also performed on a brick fragment which was connected to the mortar, resulting in a TL age of 1095 +/- 190 a.

Electric breakdown during the pulsed current spreading in the sand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vasilyak, L. M., E-mail: vasilyak@ihed.ras.ru; Vetchinin, S. P.; Panov, V. A.

2016-03-15

Processes of spreading of the pulsed current from spherical electrodes and an electric breakdown in the quartz sand are studied experimentally. When the current density on the electrode exceeds the critical value, a nonlinear reduction occurs in the grounding resistance as a result of sparking in the soil. The critical electric field strengths for ionization and breakdown are determined. The ionization-overheating instability is shown to develop on the electrode, which leads to the current contraction and formation of plasma channels.

A further study on seismic response of a set of parallel rock fractures filled with viscoelastic materials

NASA Astrophysics Data System (ADS)

Wu, W.; Zhu, J. B.; Zhao, J.

2013-02-01

The purpose of this study is to further investigate the seismic response of a set of parallel rock fractures filled with viscoelastic materials, following the work by Zhu et al. Dry quartz sands are used to represent the viscoelastic materials. The split Hopkinson rock bar (SHRB) technique is modified to simulate 1-D P-wave propagation across the sand-filled parallel fractures. At first, the displacement and stress discontinuity model (DSDM) describes the seismic response of a sand-filled single fracture. The modified recursive method (MRM) then predicts the seismic response of the sand-filled parallel fractures. The SHRB tests verify the theoretical predictions by DSDM for the sand-filled single fracture and by MRM for the sand-filled parallel fractures. The filling sands cause stress discontinuity across the fractures and promote displacement discontinuity. The wave transmission coefficient for the sand-filled parallel fractures depends on wave superposition between the fractures, which is similar to the effect of fracture spacing on the wave transmission coefficient for the non-filled parallel fractures.

The Changing Dunes of Wirtz Crater

NASA Image and Video Library

2017-01-19

The large dark feature is a classic Martian sand dune. Most sand on Earth is made from the mineral quartz, which is white and bright. On Mars, most sand is composed of dark basalt, a volcanic rock. For this reason, dunes on Mars are darker than those on Earth. The dunes in this observation, within Wirtz Crater, are known as "barchans." The steepest slope is on the eastern (right) side, partially in shadow, and represents the direction the dune is migrating as the sand is blown and transported by the wind. Small ripples are visible on much of the dune surface. The dark streaks on the dune are tracks left by passing vortices known to us as dust devils. These raise dust off the dune, revealing a darker substrate. http://photojournal.jpl.nasa.gov/catalog/PIA12289

The chemistry of Saudi Arabian sand: A deposition problem on helicopter turbine airfoils

NASA Technical Reports Server (NTRS)

Smialek, James L.

1991-01-01

Recent operations in the Persian Gulf have exposed military helicopter turbines to excessive amounts of ingested sand. Fine particles, less than 10 microns, are able to bypass the particle separators and enter the cooling and combustion systems. The initial sand chemistry varies by location, but is made up of a calcium aluminum silicate glass, SiO2 low quartz (Ca,Mg) CO3 dolomite, CaCO3 calcite, and occasionally CaCl rocksalt. The sand reacts in the hot combustion gases and deposits onto the turbine vanes as CaSO4, glass, and various crystalline silicates. Deposits up to 0.25 in. thick have been collected. Although cooling hole plugging is a considerable problem, excessive corrosion is not commonly observed due to the high melting point of GaSO4.

The chemistry of Saudi Arabian sand - A deposition problem on helicopter turbine airfoils

NASA Astrophysics Data System (ADS)

Smialek, James L.; Archer, Frances A.; Garlick, Ralph G.

Operations in the Persian Gulf have exposed military helicopter turbines to excessive amounts of ingested sand. Fine particles, less than 10 microns, are able to bypass the particle separators and enter the cooling and combustion systems. The initial sand chemistry varies by location, but is made up of a calcium aluminum silicate glass, SiO2 low quartz, (Ca,Mg)CO3 dolomite, CaCO3 calcite, and occasionally NaCl rocksalt. The sand reacts in the hot combustion gases and deposits onto the turbine vanes as CaSO4, glass, and various crystalline silicates. Deposits up to 5 mm thick have been collected. Although cooling hole plugging is a considerable problem, excessive corrosion is not commonly observed due to the high melting point of CaSO4.

The Chemistry of Saudi Arabian Sand - A Deposition Problem on Helicopter Turbine Airfoils

NASA Technical Reports Server (NTRS)

Smialek, James L.; Archer, Frances A.; Garlick, Ralph G.

1992-01-01

Operations in the Persian Gulf have exposed military helicopter turbines to excessive amounts of ingested sand. Fine particles, less than 10 microns, are able to bypass the particle separators and enter the cooling and combustion systems. The initial sand chemistry varies by location, but is made up of a calcium aluminum silicate glass, SiO2 low quartz, (Ca,Mg)CO3 dolomite, CaCO3 calcite, and occasionally NaCl rocksalt. The sand reacts in the hot combustion gases and deposits onto the turbine vanes as CaSO4, glass, and various crystalline silicates. Deposits up to 5 mm thick have been collected. Although cooling hole plugging is a considerable problem, excessive corrosion is not commonly observed due to the high melting point of CaSO4.

Clastic dikes of the Hatrurim basin (western flank of the Dead Sea) as natural analogues of alkaline concretes: Mineralogy, solution chemistry, and durability

NASA Astrophysics Data System (ADS)

Sokol, E. V.; Gaskova, O. L.; Kozmenko, O. A.; Kokh, S. N.; Vapnik, E. A.; Novikova, S. A.; Nigmatulina, E. N.

2014-11-01

This study shows that the mineral assemblages from clastic dikes in areas adjacent to the Dead Sea graben may be considered as natural analogues of alkaline concretes. The main infilling material of the clastic dikes is composed of well-sorted and well-rounded quartz sand. The cement of these hard rocks contains hydroxylapophyllite, tacharanite, calcium silicate hydrates, opal, calcite, and zeolite-like phases, which is indicative of a similarity of the natural cementation processes and industrial alkaline concrete production from quartz sands and industrial alkaline cements. The quartz grains exhibit a variety of reaction textures reflecting the interaction with alkaline solutions (opal and calcium hydrosilicate overgrowths; full replacement with apophyllite or thomsonite + apophyllite). The physicochemical analysis and reconstruction of the chemical composition of peralkaline Ca, Na, and K solutions that formed these assemblages reveal that the solutions evolved toward a more stable composition of zeolite-like phases, which are more resistant to long-term chemical weathering and atmospheric corrosion. The 40Ar/39Ar age of 6.2 ± 0.7 Ma obtained for apophyllite provides conclusive evidence for the high corrosion resistance of the assemblages consisting of apophyllite and zeolite-like phases.

Map showing high-purity silica sand of Middle Ordovician age in the Midwestern states

USGS Publications Warehouse

Ketner, Keith B.

1979-01-01

Certain quartz sands of Middle Ordovician age in the Midwestern States are well known for their purity and are exploited for a wide variety of industrial uses. The principal Middle Ordovician formations containing high-purity sands are the St. Peter Sandstone which crops out extensively from Minnesota to Arkansas; the Everton Formation principally of Arkansas; and the Oil Creek, McLish, and Tulip Creek Formations (all of the Simpson Group) of Oklahoma. The St. Peter and sandy beds in the other formations are commonly called "sandstones," but a more appropriate term is "sands" for in most fresh exposures they are completely uncemented or very weakly cemented. On exposure to air, uncemented sands usually become "case hardened" where evaporating ground water precipitates mineral matter at the surface; but this is a surficial effect. This report summarizes the available information on the extent of exposures, range of grain size, and chemical composition of the Middle Ordovician sands.

Influence of clay particles on the transport and retention of titanium dioxide nanoparticles in quartz sand.

PubMed

Cai, Li; Tong, Meiping; Wang, Xueting; Kim, Hyunjung

2014-07-01

This study investigated the influence of two representative suspended clay particles, bentonite and kaolinite, on the transport of titanium dioxide nanoparticles (nTiO2) in saturated quartz sand in both NaCl (1 and 10 mM ionic strength) and CaCl2 solutions (0.1 and 1 mM ionic strength) at pH 7. The breakthrough curves of nTiO2 with bentonite or kaolinite were higher than those without the presence of clay particles in NaCl solutions, indicating that both types of clay particles increased nTiO2 transport in NaCl solutions. Moreover, the enhancement of nTiO2 transport was more significant when bentonite was present in nTiO2 suspensions relative to kaolinite. Similar to NaCl solutions, in CaCl2 solutions, the breakthrough curves of nTiO2 with bentonite were also higher than those without clay particles, while the breakthrough curves of nTiO2 with kaolinite were lower than those without clay particles. Clearly, in CaCl2 solutions, the presence of bentonite in suspensions increased nTiO2 transport, whereas, kaolinite decreased nTiO2 transport in quartz sand. The attachment of nTiO2 onto clay particles (both bentonite and kaolinite) were observed under all experimental conditions. The increased transport of nTiO2 in most experimental conditions (except for kaolinite in CaCl2 solutions) was attributed mainly to the clay-facilitated nTiO2 transport. The straining of larger nTiO2-kaolinite clusters yet contributed to the decreased transport (enhanced retention) of nTiO2 in divalent CaCl2 solutions when kaolinite particles were copresent in suspensions.

Spatial patterns in heavy-mineral concentrations along the Curonian Spit coast, southeastern Baltic Sea

NASA Astrophysics Data System (ADS)

Pupienis, Donatas; Buynevich, Ilya; Ryabchuk, Daria; Jarmalavičius, Darius; Žilinskas, Gintautas; Fedorovič, Julija; Kovaleva, Olga; Sergeev, Alexander; Cichoń-Pupienis, Anna

2017-08-01

The 98-km-long Curonian Spit is fronted by beaches mainly composed of quartz sand with minor high-density fractions. In this study heavy-mineral concentration (HMC) trends and grain-size statistical parameters were used to assess their role as indicators of natural processes, human activities, and patterns of longshore transport. A total of 92 surface sand samples were collected at 1 km intervals from the middle of the beach along the Baltic Sea shoreline of the spit between Klaipėda strait in Lithuania and Zelenogradsk in Russia. HMC contribution was assessed in the laboratory using bulk low-field magnetic susceptibility (MS) as a proxy for ferrimagnetic and paramagnetic mineral content. Quartz-dominated (background) sand is generally characterized by low MS values of κ < 50 μSI, whereas higher values κ > 150 μSI are typical for heavy-mineral-rich sand. The greatest MS values along the middle of the beach occur in the southern part of the spit and are 40 times higher than in the northern sector. This pattern suggests the existence of a longshore particle flux with HMC distribution having the potential as a useful tracer of longshore sediment transport. Local anomalously high MS excursions are associated with contribution of iron-rich materials from adjacent man-made structures. Therefore, temporally constrained HMC distribution along the middle of the beach reflects the cumulative effect of antecedent geologic framework, longshore sediment transfer, erosional and accretionary processes, wave and wind climate, and local coastal protective structures.

Natural Silica Sand/Alumina Ceramic Composites: Promising Candidates for Fuel-Cell Sealants

NASA Astrophysics Data System (ADS)

Hidayat, N.; Istiqomah; Widianto, M. Y. H.; Taufiq, A.; Sunaryono; Triwikantoro; Zainuri, M.; Baqiya, M. A.; Aristia, G.; Pratapa, S.

2017-05-01

An attempt has been developed to establish the prospect of the useful application of Indonesian natural silica sand, instead of commercially expensive materials, as a future fuel-cell sealant. The sand was initially washed and ball-milled at 150 rpm for 60 minutes and then heated at 1000 °C for the same duration. The resulting powder was then mixed with alumina powder at various amounts and shaped into discs before sintering at 1150 °C and 1250 °C to produce compact ceramics. The diameter shrinkage, porosity, and density of the ceramics were evaluated by Archimedes method. Their crystalline phase composition was quantified by Rietveld refinement analysis on the X-ray diffraction (XRD) data and the phase weight fraction was then used for coefficient of thermal expansion (CTE) evaluation. It was observed that the bulk density increased while the porosity decreased with alumina addition. The XRD data analysis revealed that the prepared silica sand contains a very high purity of quartz-SiO2, i.e. 97.8(18)%. The sintering temperatures of 1150 °C and 1250 °C transformed some quartz-SiO2 to crystobalite-SiO2. All the calcite-CaCO3 exhibited reaction sintering with SiO2 forming wollastonite-CaSiO3. Therefore, the ceramic composites contained SiO2/Al2O3/CaSiO3. Regarding CTE, all of the composites meet the criteria for fuel-cell sealants, in the range of 9-12 ppm/°C.

A probable martian analogue in muttom in southern india

NASA Astrophysics Data System (ADS)

Wankhede, Tushar; Rajesh, V. J.; Charri, Abhishek

2012-07-01

Mars, a terrestrial planet fourth from the Sun in the solar system, is widely known as the red planet. The iron oxide sand/dust is predominant on its surface and gives the reddish appearance. Recent explorations have exposed abundance of haematite-rich loose materials in the surface of Mars especially at Meridiani Planum. Sedimentary structures like bedding, cross-bedding, ripple marks, gullies, mud cracks etc. are identified in this area. It is essential to look for some terrestrial analogues for the iron oxide rich sand/dust in order to explore their genetic mechanisms in Martian surface. Red sand beds occur above the crystalline basement or younger calcareous sandstone/limestone as isolated patches of partly indurated or unindurated dunes and sheets fringing the south western coastal lands of Tamil Nadu. Calcretes, source of carbonates, also occur at places within these red sand beds. Muttom soils are dark red in color on fresh surfaces. The red sand beds are dominated by iron-bearing minerals such as hematite and ilmenite. Local patches of heavy mineral deposition by the action of wind and water were also observed in the Muttom area. Preliminary spectral analyses confirmed the presence of iron bearing minerals like hematite and ilmenite which are also present in Mars. Many sedimentary structures like gullies, channels, polygonal mud cracks, erosion pits and dunes were present in Muttom area similar to those observed on Martian surface. Meridiani planum outcrops are composed of some siliciclastics grains, and hematite, and only few deposits on Earth match this description. The siliciclastics grains are primarily quartz grain coated with hematite. Quartz is also found in Muttom which, may have been transported by the action of wind while in the Mars siliciclastics is the alteration product of basalt. The structures are more or less similar to those observed at Meridiani Planum. Previous workers interpreted these red sands as `unique' formed either by a mixed beach and dune environment, or as similar to colluvium (formed by mass wasting and fluvial processes). Comparative studies between the red sand beds formations on Martian surface and southern Tamil Nadu can provide valuable insights on the origin, weathering pattern, tectonics and depositional environment of red sand beds in Mars.

Comparison of Rotavirus and Norovirus transport in standardised and natural soil-water systems

NASA Astrophysics Data System (ADS)

Gamazo, P. A.; Schijven, J. F.; Victoria, M.; Alvareda, E.; Lopez, F.; Ramos, J.; Lizasoain, A.; Sapriza-Azuri, G.; Castells, M.; Colina, R.

2016-12-01

Rotavirus and Norovirus are waterborne viruses that are major causes of diarrhea and others symptoms of acute gastroenteritis. An important pathway of these viruses is groundwater. In Uruguay, as in many developed and developing countries, there are areas where the only source of water for human consumption is groundwater. In the rural area of the Salto district, groundwater is commonly used without any treatment, as it is traditionally considered as a safe source. However, virus contamination have been detected in several wells in the area. The most probable source of contamination are nearby septic systems, since the sewer coverage is scarce. This work aims to evaluate and compare the virus transport processes for a standardised soil-water systems and for the Salto aquifer system. For this, the transport of Rotavirus and Norovirus from clinic samples was studied in two sets of column experiments: 6.7 cm columns with quartz sand under saturated conditions (ionic strength 1mM, pH 7.0) and with sand from the Salto aquifer (Uruguay) (9,2% coarse sand, 47,8% medium sand, 40,5% fine sand, magnesium/calcium bicarbonate water, Ionic strength 15.1 mM, pH 7.2). Both viruses were seeded for 2 pore volumes on the columns. Samples were collected at the column outlet and viruses were enumerated by Q-PRCR. Breakthrough curves were constructed and fitted to a two-site kinetic attachment/detachment model, including blocking using Hydrus-1D. In the quartz sand column, both Rotavirus and Norovirus were removed two orders in magnitude. In the Salto sand column, Rotavirus was removed 2 log10 as well, but Norovirus was removed 4 log10. The fitting of the breakthrough curves indicated that blocking played a role for Rotavirus in the Salto sand column. These results are consistent with field observation where only Rotavirus was detected in the Salto aquifer, while similar concentrations in Salto sewer effluent was measured for these two viruses. This work, besides reporting actual parameters values for human virus transport modelling, shows the significant differences in transport that human viruses can have in standardised and natural soil-water systems.

Surface texture analysis of southern Tuli Basin sediments: Implications for Limpopo Valley geoarchaeological contexts

NASA Astrophysics Data System (ADS)

Le Baron, Joel C.; Grab, Stefan W.; Kuman, Kathleen

2011-03-01

The Hackthorne 1 site (southern Tuli Basin, South Africa) is situated on a sand-covered plateau adjacent to the Limpopo River Valley. Although the site is well known for its Stone Age archaeology, the past environmental contexts (particularly sedimentological/geomorphological) are not well known. We examine the Hackthorne sand grain surface textures, so as to provide some insight on the site specific and regional depositional history. Quartz sands at Hackthorne were collected from surface sands and from underlying weathered calcrete. SEM analysis was performed on sand grains, through which several mechanical and chemical microtextures were identified. Microtextures typical of fluvial environments were found only on grains derived from the plateau calcrete host sediment, whilst the surface sands exhibited only textures associated with aeolian environments. The results indicate that the calcrete host sediment is composed of alluvium, and that the surface sands mantling the Hackthorne Plateau are not deflated from the alluvial deposits in the Limpopo Valley, but may rather be derived from distant aeolian sources. The deposition of aeolian sands is consistent with OSL dates which place sand deposition, or remobilization, at 23 and 15 kya, periods in southern Africa associated with increased aridity.

Optical Dating of Holocene Dune Sands in the Ferris Dune Field, Wyoming

NASA Astrophysics Data System (ADS)

Stokes, Stephen; Gaylord, David R.

1993-05-01

Optical dating of late Quaternary quartz dune sands from the Clear Creek portion of Ferris dune field, Wyoming, demonstrates the considerable potential of the technique as a chronostratigraphic tool. A sequence of radiocarbon-dated Holocene interdune strata permit optical dating of the intercalated dune sand to be tested; the concordance is good. The optical dates for the aeolian deposits not datable by radiocarbon suggest that aeolian sedimentation at Clear Creek peaked during two relatively short phases at ca. 8500 and 4000 yr B.P. The dates indicate that aeolian accumulation maxima (at least in the Clear Creek area) may not be synchronous with previously defined phases of marked aridity.

Understanding and Mitigating Reservoir Compaction: an Experimental Study on Sand Aggregates

NASA Astrophysics Data System (ADS)

Schimmel, M.; Hangx, S.; Spiers, C. J.

2016-12-01

Fossil fuels continue to provide a source for energy, fuels for transport and chemicals for everyday items. However, adverse effects of decades of hydrocarbons production are increasingly impacting society and the environment. Production-driven reduction in reservoir pore pressure leads to a poro-elastic response of the reservoir, and in many occasions to time-dependent compaction (creep) of the reservoir. In turn, reservoir compaction may lead to surface subsidence and could potentially result in induced (micro)seismicity. To predict and mitigate the impact of fluid extraction, we need to understand production-driven reservoir compaction in highly porous siliciclastic rocks and explore potential mitigation strategies, for example, by using compaction-inhibiting injection fluids. As a first step, we investigate the effect of chemical environment on the compaction behaviour of sand aggregates, comparable to poorly consolidated, highly porous sandstones. The sand samples consist of loose aggregates of Beaujean quartz sand, sieved into a grainsize fraction of 180-212 µm. Uniaxial compaction experiments are performed at an axial stress of 35 MPa and temperature of 80°C, mimicking conditions of reservoirs buried at three kilometres depth. The chemical environment during creep is either vacuum-dry or CO2-dry, or fluid-saturated, with fluids consisting of distilled water, acid solution (CO2-saturated water), alkaline solution (pH 9), aluminium solution (pH 3) and solution with surfactants (i.e., AMP). Preliminary results show that compaction of quartz sand aggregates is promoted in a wet environment compared to a dry environment. It is inferred that deformation is controlled by subcritical crack growth when dry and stress corrosion cracking when wet, both resulting in grain failure and subsequent grain rearrangement. Fluids inhibiting these processes, have the potential to inhibit aggregate compaction.

Fusion of arkosic sand by intrusive andesite

USGS Publications Warehouse

Bailey, Roy A.

1954-01-01

An andesite dike in the Valles Mountains of northern New Mexico has intruded and partly fused arkosic sediments for a distance of 50 feet from its contacts. The dike is semi-circular in form, has a maximum width of about 100 feet, and is about 500 feet long. Small associated arcuate dikes are arranged in spiral fashion around the main dike, suggesting that they were intruded along shear fractures similar to those described by Burbank (1941). The fused rocks surrounding the andesite dike are of three general types: 1) partly fused arkosic sand, 2) fused clay, and 3) hybrid rocks. The fused arkosic sand consists of relict detrital grains of quartz, orthoclose, and plagioclase, imbedded in colorless glass containing microlites of tridymite, cordierite, and magnetite. The relict quartz grains are corroded and embayed by glass; the orthoclase is sanidinized and partly fused; and the plagioclase is inverted to the high temperature form and is partly fused. The fused clay, which was originally a mixture of montmorillonite and hydromica, consists primarily of cordierite but also contains needle-like crystals of sillimanite (?) or mullite (?). The hybrid rocks originated in part by intermixing of fused arkosic sediments and andesitic liquid and in part by diffusion of mafic constituents through the fused sediments. They are rich in cordierite and magnetite and also contain hypersthene, augite, and plagioclase. The composition of pigeonite in the andesite indicates that the temperature of the andesite at the time of intrusion probably did not exceed 1200?C. Samples of arkosic sand were fused in the presence of water in a Morey bomb at 1050?C. Stability relations of certain minerals in the fused sand suggest that fusion may have taken place at a lower temperature, however, and the fluxing action of volatiles from the andesite are thought to have made this possible.

Comparisons of the film peeling from the composite oxides of quartz sand filters using ozone, hydrogen peroxide and chlorine dioxide.

PubMed

Guo, Yingming; Huang, Tinglin; Wen, Gang; Cao, Xin

2015-08-01

To solve the problem of shortened backwashing intervals in groundwater plants, several disinfectants including ozone (O3), hydrogen peroxide (H2O2) and chlorine dioxide (ClO2) were examined to peel off the film from the quartz sand surface in four pilot-scale columns. An optimized oxidant dosage and oxidation time were determined by batch tests. Subsequently, the optimized conditions were tested in the four pilot-scale columns. The results demonstrated that the backwashing intervals increased from 35.17 to 54.33 (H2O2) and to 53.67 hr (ClO2) after the oxidation treatments, and the increase of backwashing interval after treatment by O3 was much less than for the other two treatments. Interestingly, the treatment efficiency of filters was not affected by O3 or H2O2 oxidation; but after oxidation by ClO2, the treatment efficiency was deteriorated, especially the ammonia removal (from 96.96% to 24.95%). The filter sands before and after the oxidation were characterized by scanning electron microscopy and X-ray photoelectron spectroscopy. Compared with the oxidation by O3 and H2O2, the structures on the surface of filter sands were seriously damaged after oxidation by ClO2. The chemical states of manganese on the surfaces of those treated sands were only changed by ClO2. The damage of the structures and the change of the chemical states of manganese might have a negative effect on the ammonia removal. In summary, H2O2 is a suitable agent for film peeling. Copyright © 2015. Published by Elsevier B.V.

Mobility of multiwalled carbon nanotubes in porous media.

PubMed

Liu, Xueying; O'Carroll, Denis M; Petersen, Elijah J; Huang, Qingguo; Anderson, C Lindsay

2009-11-01

Engineered multiwalled carbon nanotubes (MWCNTs) are the subject of intense research and are expected to gain widespread usage in a broad variety of commercial products. However, concerns have been raised regarding potential environmental and human health risks. The mobility of MWCNTs in porous media is examined in this study using one-dimensional flow-through column experiments under conditions representative of subsurface and drinking water treatment systems. Results demonstrate that pore water velocity strongly influenced MWCNT transport, with high MWCNT mobility at pore water velocities greater than 4.0 m/d. A numerical simulator, which incorporated a newly developed theoretical collector efficiency relationship for MWCNTs in spherical porous media, was developed to model observed column results. The model, which incorporated traditional colloid filtration theory in conjunction with a site-blocking term, yielded good agreement with observed results in quartz sand-packed column experiments. Experiments were also conducted in glass bead-packed columns with the same mean grain size as the quartz sand-packed columns. MWCNTs were more mobile in the glass bead-packed columns.

Hydrothermal deformation of granular quartz sand

NASA Astrophysics Data System (ADS)

Karner, Stephen L.; Kronenberg, Andreas K.; Chester, Frederick M.; Chester, Judith S.; Hajash, Andrew

2008-05-01

Isotropic and triaxial compression experiments were performed on porous aggregates of St Peter quartz sand to explore the influence of temperature (to 225°C). During isotropic stressing, samples loaded at elevated temperature exhibit the same sigmoidal stress-strain curves and non-linear acoustic emission rates as have previously been observed from room temperature studies on sands, sandstones, and soils. However, results from our hydrothermal experiments show that the critical effective pressure (P*) associated with the onset of significant pore collapse and pervasive cataclastic flow is lower at increased temperature. Samples subjected to triaxial loading at elevated temperature show yield behavior resembling that observed from room temperature studies on granular rocks and soils. When considered in terms of distortional and mean stresses, the yield strength data for a given temperature define an elliptical envelope consistent with critical state and CAP models from soil mechanics. For the conditions we tested, triaxial yield data at low effective pressure are essentially temperature-insensitive whereas yield levels at high effective pressure are lowered as a function of elevated temperature. We interpret our yield data in a manner consistent with Arrhenius behavior expected for thermally assisted subcritical crack growth. Taken together, our results indicate that increased stresses and temperatures associated with subsurface burial will significantly alter the yield strength of deforming granular media in systematic and predictable ways.

Processes and kinetics of Cd2+ sorption by a calcareous aquifer sand

USGS Publications Warehouse

Fuller, C.C.; Davis, J.A.

1987-01-01

The rate of Cd2+ sorption by a calcareous aquifer sand was characterized by two reaction steps, with the first step reaching completion in 24 hours. The second step proceeded at a slow and nearly constant rate for at least seven days. The first step includes a fast adsorption reaction which is followed by diffusive transport into either a disordered surface film of hydrated calcium carbonate or into pore spaces. After 24 hours the rate of Cd2+ sorption was constant and controlled by the rate of surface coprecipitation, as a solid solution of CdCO3 in CaCO3 formed in recrystallizing material. Desorption of Cd2+ from the sand was slow. Clean grains of primary minerals, e.g. quartz and aluminosilicates. sorbed much less Cd2+ than grains which had surface patches of secondary minerals, e.g. carbonates, iron and manganese oxides. Calcite grains sorbed the greatest amount of Cd2+ on a weight-normalized basis despite the greater abundance of quartz. A method is illustrated for determining empirical binding constants for trace metals at in situ pH values without introducing the experimental problem of supersaturation. The binding constants are useful for solute transport models which include a computation of aqueous speciation. ?? 1987.

Elemental Characterization of Hardpan Topping Selected Sections of Ajali Sand, Anambra Basin. Nigeria.

NASA Astrophysics Data System (ADS)

Ajidahun, E. J.

2015-12-01

The hardpan cap of selected sections of loose Ajali sand in Anambra Basin of Nigeria was investigated for elemental compositions using Energy Dispersive X-Ray Fluorescence mapping (M4-Tornado ED-XRF); while bulk mineralogy was determined by X-Ray Diffraction and Scanning Electron Microscopy (SEM) at the Federal Institute for Geosciences and Natural Resources (BGR), Hannover, Germany. Elemental maps of Fe, Si, Ti, Al, Cr etc. were used to highlight texture and mineral distribution. The Ajali sands are locally topped by iron rich hardpans. These hardpans consist of rock fragments up to several cm in length in a primary matrix and locally large pores. Besides laminated sandstone fragments, highly altered porphyritic volcanic rocks can be observed. The latter in the SEM appear highly spongeous, and show relics of phenochryts such as biotite, hornblende and pyroxene, corroded magmatic quartz, magnetite, Ilmenite, zircon or voids of former crystals in an almost entirely altered matrix Large pores show several generations of periodic infill of quartz sand / soil mixtures alternating with multiple layers of Fe rich precipitates, locally enriched in Al, P, S, Mn or Sr agglutinating the fines. Volcanic fragments show rims of elevated Cr content, and Cr and V-rich precipitates may separate generations of infill. A number of large open pore channels rimmed by Fe-rich matrix might act as water channels. They are coated by Al, K rich precipitates. Ajali sands can hardly be considered as the source for the agglutination of the hardpan cap. The source of Fe and other elements such as Al, K, Cr, V has to be attributed to the volcanic fragments, mainly to the matrix, but to the altered phenocrysts, too. Toxic elements such as Cr being mobile in the system are in part stabilized as precipitates. EDXRF-micro mapping provides excellent textural, chemical and even mineralogical information to get better insight into the sedimentation and agglutination history of the hardpan cap. Key words: Hardpan Cap, Ajali Sands, Anambra Basin, Agglutination, Volcanic Fragment.

The Late Cambrian SPICE (δ13C) event and the Sauk II-Sauk III regression: new evidence from Laurentian basins in Utah, Iowa, and Newfoundland

USGS Publications Warehouse

Saltzman, Matthew R.; Cowan, Clinton A.; Runkel, Anthony C.; Runnegar, Bruce; Stewart, Michael C.; Palmer, Allison R.

2004-01-01

Carbon isotope data from Upper Cambrian sections in three Laurentian basins in northern Utah, central Iowa, and western Newfoundland record a large positive ??13C excursion (SPICE event) of up to + 5???. Peak ??13C ratios are well dated by trilobite collections to the middle of the Steptoean Stage (Dunderbergia Zone) and occur during maximum regression associated with formation of the Sauk II-Sauk III subsequence boundary on the North American craton. Maximum regression was marked by an influx of quartz sand into carbonate-platform settings in all three widely separated basins. In northern Utah, this quartz sand formed a thick sequence known as the Worm Creek Quartzite, which marks a conspicuous interruption of carbonate deposition during the Middle to Late Cambrian in the region. In western Newfoundland, the thickness of the quartz sand unit is much reduced but still marks a brief shutdown of the carbonate factory that is unique to the Cambrian shelf succession of the area. In the central Iowa area of the cratonic interior, an upward-shallowing carbonate succession culminates in cross-stratified trilobite grainstones at the peak of the SPICE in Dunderbergia Zone time, and the lowest point on the relative-sea-level curve is associated with the occurrence of coarse quartz sand derived from the encroaching shoreface. Although it is difficult to determine precisely the departure from baseline ??13C that marks the beginning of the SPICE excursion in the stratigraphic successions analyzed, our results are consistent with a rise and subsequent fall in ??13C tracking a major regressive-transgressive event recorded across northern Laurentia. The correlation of a major ??13C excursion with regression is similar to that described for the Late Ordovician, for which the pattern has been attributed to either increased carbonate relative to terrigenous weathering rates as ice sheets covered up organic-matter-containing silicates at high latitudes or high productivity and organic-carbon burial driven by oceanic overturn. The lack of known Steptoean-age ice sheets that could have affected the ratio of carbonate to silicate weathering rates suggests that organic-carbon burial was the likely cause of the SPICE event. We suggest that increased weathering and erosion rates during relative sea-level fall (Sauk II-III) increased the burial fraction of organic carbon in an expanded region of fine-grained siliciclastic deposits in shelf and upper slope environments during the Steptoean. ?? 2004, SEPM (Society for Sedimentary Geology).

FILTRATION OF RECOMBINANT NORWALK VIRUS PARTICLES AND BACTERIOPHAGE MS2 IN QUARTZ SAND: IMPORTANCE OF ELECTROSTATIC INTERACTIONS. (R824775)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

PHYSICOCHEMICAL MECHANISMS RESPONSIBLE FOR THE FILTRATION AND MOBILIZATION OF A FILAMENTOUS BACTERIOPHAGE IN QUARTZ SAND. (R824775)

EPA Science Inventory

This study examines the influence of pore water chemistry on the filtration and physicochemical properties of a male-specific filamentous bacteriophage isolated from
chlorinated effluent of the San Jose Creek Water Reclamation Plant in Los Angeles County, California. The isola...

Observation of angular effects on thermal infrared emissivity derived with the MODTES algorithm and MODIS data

NASA Astrophysics Data System (ADS)

García-Santos, Vicente; Niclòs, Raquel; Coll, César; Valor, Enric; Caselles, Vicente

2015-04-01

The MOD21 Land Surface Temperature and Emissivity (LST&E) product will be included in forthcoming MODIS Collection 6. Surface temperature and emissivities for thermal infrared (TIR) bands 29 (8.55 μm), 31 (11 μm) and 32 (12 μm) will be retrieved using the ASTER TES method adapted to MODIS at-sensor spectral radiances, previously corrected with the Water Vapor Scaling method (MODTES algorithm). LSE of most natural surfaces changes with soil moisture content, type of surface cover, surface roughness or sensor viewing geometry. The present study addresses the observation of anisotropy effects on LSE of bare soils using MODIS data and a processor simulator of the MOD21 product, since it is not available yet. Two highly homogeneous and quasi-invariant desert sites were selected to carry out the present study. The first one is the White Sands National Monument, located in Tularosa Valley (South-central New Mexico, USA), which is a dune system desert at 1216 m above sea level, with an area of 704 km2 and a maximum dune height of 10 m. The grain size is considered fine sand and the major mineralogy component is gypsum. The second site selected was the Great Sands National Park, located in the San Luis Valley (Colorado, USA). Great Sands is also a sand dune system desert, created from quartz and volcanic fragments derived from Santa Fe and Alamosa formations. The major mineral is quartz, with minor traces of potassium and feldspar. The grain size of the sand is medium to coarse according to the X-Ray Diffraction measurements. Great Sands covers an area of 104 km2 at 2560 m above sea level and the maximum dune height is 230 m. The obtained LSEs and their dependence on azimuth and zenith viewing angles were analyzed, based on series of MODIS scenes from 2010 to 2013. MODTES nadir and off-nadir LSEs showed a good agreement with laboratory emissivity measurements. Results show that band 29 LSE decreases with the zenithal angle up to 0.041 from its nadir value, while LSEs for bands 31 and 32 do not show significant changes with zenith angle.

Investigation the Effect of the Dispersant Corexit 9500A on the Movement of an Oil-In-Water Emulsion Through an Alabama Beach Sand

NASA Astrophysics Data System (ADS)

Steffy, D. A.; Nichols, A.

2016-02-01

A majority of Alabama's 60 miles of beaches were exposed to the crude oil released from the massive 2010 Deepwater Horizon Oil Spill. To help remediate the spill BP sprayed the dispersant, COREXIT 9500A, over the floating oil in the Gulf and at the subsurface damaged Macondo wellhead. This dispersant could have inadvertently promoted an oil-in-water emulsion to infiltrate deeper into the exposed beaches which are composed of Holocene age, fine-to-medium quartz sand. A series of short-column tests of packed sand in glass columns simulated the arrival of an oil-in-water emulsion at a beach. An emulsion formed by weathered oil penetrated deeper into the sand as compared to oil that has experience little weathering. The penetrations of these emulsions were enhanced when a 2% COREXIT 9500A in saltwater solution was allowed to flush through the sand column. Unfortunately, by adding a dispersant it probably promoted some oil-in-water components to be distributed deeper into coastal sand of Alabama.

Use of bauxite as packing material in steam injection wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scoglio, J.; Joubert, G.; Gallardo, B.

1995-12-31

Cyclic steam injection, also known as steam soak, has proven to be the most efficient method for producing heavy crude oil and bitumen from unconsolidated sands. The application of steam injection may, however, generate sand production, causing, among other things, a decrease in production. The gravel pack technique is the most efficient way to prevent fines production from cold producing wells. But, once they are steam stimulated, a dissolution of quartz containing gravel material takes place reducing greatly the packing permeability and eventually sand production. Different types of packing material have been used to avoid sand production after cyclic steammore » injection, such as gravel, ceramics, bauxite, coated resin, and American sand. This paper presents the results of field test, using sinterized bauxite as a packing material, carried out in Venezuela`s heavy oil operations as a part of a comprehensive program aimed at increasing the packing durability and reducing sand production. This paper also verify the results of laboratory tests in which Bauxite was found to be less soluble than other packing material when steam injected.« less

Recent research on the Chesapeake Bay impact structure, USA - Impact debris and reworked ejecta

USGS Publications Warehouse

Horton, J. Wright; Aleinikoff, John N.; Kunk, Michael J.; Gohn, Gregory S.; Edwards, Lucy E.; Self-Trail, Jean M.; Powars, David S.; Izett, Glen A.

2005-01-01

Four new coreholes in the western annular trough of the buried, late Eocene Chesapeake Bay impact structure provide samples of shocked minerals, cataclastic rocks, possible impact melt, mixed sediments, and damaged microfossils. Parautochthonous Cretaceous sediments show an upward increase in collapse, sand fluidization, and mixed sediment injections. These impact-modified sediments are scoured and covered by the upper Eocene Exmore beds, which consist of highly mixed Cretaceous to Eocene sediment clasts and minor crystalline-rock clasts in a muddy quartz-glauconite sand matrix. The Exmore beds are interpreted as seawater-resurge debris flows. Shocked quartz is found as sparse grains and in rock fragments at all four sites in the Exmore, where these fallback remnants are mixed into the resurge deposit. Crystalline-rock clasts that exhibit shocked quartz or cataclastic fabrics include felsites, granitoids, and other plutonic rocks. Felsite from a monomict cataclasite boulder has a sensitive high-resolution ion microprobe U-Pb zircon age of 613 ± 4 Ma. Leucogranite from a polymict cataclasite boulder has a similar Neoproterozoic age based on muscovite 40Ar/39Ar data. Potassium-feldspar 40Ar/39Ar ages from this leucogranite show cooling through closure (∼150 °C) at ca. 261 Ma without discernible impact heating. Spherulitic felsite is under investigation as a possible impact melt. Types of crystalline clasts, and exotic sediment clasts and grains, in the Exmore vary according to location, which suggests different provenances across the structure. Fractured calcareous nannofossils and fused, bubbled, and curled dinoflagellate cysts coexist with shocked quartz in the Exmore, and this damage may record conditions of heat, pressure, and abrasion due to impact in a shallow-marine environment.

Synchrotron WAXS and XANES studies of silica (SiO2) powders synthesized from Indonesian natural sands

NASA Astrophysics Data System (ADS)

Muchlis, Khairanissa; Aini Fauziyah, Nur; Soontaranon, Siriwat; Limpirat, Wanwisa; Pratapa, Suminar

2017-01-01

In this study, we have investigated polymorphic silica (SiO2) powders using, Wide Angle X-ray Scattering (WAXS) and X-Ray Absorption Near Edge Spectroscopy (XANES), laboratory X-Ray Diffraction (XRD) instruments. The WAXS and XANES spectra were collected using synchrotron radiation at Synchrotron Light Research Institute (SLRI), Nakhon Ratchasima, Thailand. The silica powders were obtained by processing silica sand from Tanah Laut, South Kalimantan, Indonesia. Purification process of silica sand was done by magnetic separation and immersion with HCl. The purification step was needed to reduce impurity or undesirable non Si elements. Three polymorphs of silica were produced, i.e. amorphous phase (A), quartz (B), and cristobalite (C). WAXS profile for each phase was presented in terms of intensity vs. 2θ prior to analyses. Both XRD (λCuKα=1.54056 Å) and WAXS (λ=1.09 Å) patttern show that (1) A sample contains no crystallites, (2) B sample is monophasic, contains only quartz, and (3) C sample contains cristobalite and trydimite. XRD quantitative analysis using Rietica gave 98,8 wt% cristobalite, while the associated WAXS data provided 98.7 wt% cristobalite. Si K-edge XANES spectra were measured at energy range 1840 to 1920 eV. Qualitatively, the pre-edge and edge features for all phases are similar, but their main peaks in the post-edge region are different.

Transport of Strontium and Cesium in Simulated Hanford Tank Waste Leachate through Quartz Sand under Saturated and Unsaturated Flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rod, Kenton A.; Um, Wooyong; Flury, Markus

2010-11-01

We investigated the effects of water saturation and formation of secondary precipitates on transport of Sr and Cs through sand columns under unsaturated water flow. A series of column experiments was run at effective water saturations ranging from 0.2 to 1.0 under steady-state flow using columns filled with quartz sand. The solution phase was either 0.1 M NaNO3 or a simulated tank waste leachate (STWL), mimicking the leaks of tank wastes at the Hanford Site, Washington, USA. In STWL, the mobility of Sr was significantly reduced as the water saturation decreased, because Sr was incorporated into or sorbed to neo-formedmore » secondary precipitates. In contrast, the transport of Cs in STWL was similar to that of a nonreactive tracer. In 0.1 M NaNO3, Sr moved like a conservative tracer, showing no retardation, whereas Cs was retarded relative to Sr. The flow regime for the 0.1 M NaNO3 columns under all water saturations could be described with the equilibrium convection-dispersion equation (CDE). However, for STWL, the Sr and Cs breakthrough curves indicated the presence of non-equilibria under unsaturated flow conditions. Such non-equilibrium conditions, caused by physical and chemical processes can reduce the mobility of radionuclides at the Hanford vadose zone.« less

Geochemical evidence for an Eolian sand dam across the North and South Platte rivers in Nebraska

USGS Publications Warehouse

Muhs, Daniel R.; Swinehart, James B.; Loope, David B.; Been, Josh; Mahan, Shannon; Bush, Charles A.

2000-01-01

Geochemical and geomorphic data from dune fields in southwestern Nebraska provide new evidence that the Nebraska Sand Hills once migrated across the North and South Platte rivers and dammed the largest tributary system to the Missouri River. The Lincoln County and Imperial dune fields, which lie downwind of the South Platte River, have compositions intermediate between the Nebraska Sand Hills (quartz-rich) and northeastern Colorado dunes (K-feldspar-rich). The most likely explanation for the intermediate composition is that the Lincoln County and Imperial dunes are derived in part from the Nebraska Sand Hills and in part from the South Platte River. The only mechanism by which the Nebraska Sand Hills could have migrated this far south is by complete infilling of what were probably perennially dry North Platte and South Platte river valleys. Such a series of events would have required an extended drought, both for activation of eolian sand and decreased discharges in the Platte River system. A nearby major tributary of the North Platte River is postulated to have been blocked by eolian sand about 12,000 14C yr B.P. We propose that an eolian sand dam across the Plattes was constructed at about this same time.

Temperature dependency of virus and nanoparticle transport and retention in saturated porous media

USDA-ARS?s Scientific Manuscript database

The influence of temperature (4 and 20 °C) on virus and nanoparticle attachment in columns packed with quartz sand was studied under various physiochemical conditions. Fitted values of the attachment rate coefficient (katt) and the solid fraction that contributed to attachment (Sf) were found to be...

Fate and Transport of Elemental Copper (Cu0) Nanoparticles through Saturated Porous Media in the Presence of Organic Materials

EPA Science Inventory

Column experiments were performed to assess the fate and transport of nanoscale elemental copper (Cu0) particles in saturated quartz sands. Both effluent concentrations and retention profiles were measured over a broad range of physicochemical conditions, which included pH, ionic...

Decomposition of nitrous oxide and chloromethanes absorbed on particulate matter

NASA Technical Reports Server (NTRS)

Rebbert, R. E.; Ausloos, P. J.

1978-01-01

The effect of pressure on the heterogeneous thermal and pyrolytic decomposition of nitrous oxides adsorbed on sand was studied. Results indicate that N20 adsorbed on certain sand surfaces can be decomposed by photons which nitrous oxide cannot absorb in the gas phase. There is also a thermal heterogeneous decomposition of nitrous oxide which also produces nitrogen. The photolysis of CC14, CFC13, CF2C12 adsorbed on fused quartz and on different types of sand was also investigated. There was no thermal heterogeneous reaction with any of these chloromethanes. Apparently the larger bond energy of approximately 74 kcal for the C-C1 bond compared to approximately 40 kcal for the N-O bond in N2O makes the thermal reaction inoperative for the chloromethanes.

PGEs and Quartz Grains in a Resedimented Late Archean Impact Horizon in the Hamersley Group of Western Australia

NASA Astrophysics Data System (ADS)

Simonson, B. M.; Davies, D.; Wallace, M.; Reeves, S.; Hassler, S.

1996-03-01

The early Precambrian Hamersley Group of Western Australia contains two thick packages of carbonate-rich strata, the Carawine Dolomite and the Wittenoom Formation, that occupy mutually exclusive areas within the Hamersley Basin. Within each of these formations is a single horizon which contains sand- to fine gravel-size particles believed to be distal ejecta from a large bolide impact. In the Carawine Dolomite, the ejecta are restricted to a coarse-grained dolomitic debris flow deposit up to 25 m thick. In the Wittenoom Formation, the ejecta are restricted to a turbidite which is <=1.3 m thick and consists largely of sand-size carbonate and argillite intraclasts. Together, these two horizons constitute a single, unique layer that appears to have been deposited rapidly over an area >= 50,000 km2 by a single high-energy event around 2.5 Ga. Deposition is inferred to have taken place in a series of distinct stages as follows: (1.) ballistic dispersal of mostly sand-size particles from the impact site to the seafloor in the Hamersley Basin, (2.) reworking of the newly deposited ejecta in the Hamersley Basin into large symmetrical ripples by impact-generated tsunami waves, and (3.) subsequent erosion and re-sedimentation of most of the ejecta by one to three large sedimentary gravity flows that moved south and west down the paleoslope of the Hamersley Basin. New data will be presented concerning the two main types of ejecta found in this layer: microkrystites and quartz grains. Specifically, microkrystite-rich samples are enriched in Ir and Ru by an order of magnitude or more relative to the surrounding strata, but other siderophile elements (Pd, Pt, Au, Cr, Co, and Ni) display neither anomalously high concentrations nor chondritic interelement ratios. As for the quartz grains, their petrographic characteristics clearly indicate they are not volcanic in origin, but they do not appear to have planar deformation features like those reported from numerous other impact ejecta horizons.

In situ treatment of arsenic contaminated groundwater by aquifer iron coating: Experimental study.

PubMed

Xie, Xianjun; Wang, Yanxin; Pi, Kunfu; Liu, Chongxuan; Li, Junxia; Liu, Yaqing; Wang, Zhiqiang; Duan, Mengyu

2015-09-15

In situ arsenic removal from groundwater by an aquifer iron coating method has great potential to be a cost effective and simple groundwater remediation technology, especially in rural and remote areas where groundwater is used as the main water source for drinking. The in situ arsenic removal technology was first optimized by simulating arsenic removal in various quartz sand columns under anoxic conditions. The effectiveness was then evaluated in an actual high-arsenic groundwater environment. The arsenic removal mechanism by the coated iron oxide/hydroxide was investigated under different conditions using scanning electron microscopy (SEM)/X-ray absorption spectroscopy, electron probe microanalysis, and Fourier transformation infrared spectroscopy. Aquifer iron coating method was developed via a 4-step alternating injection of oxidant, iron salt and oxygen-free water. A continuous injection of 5.0 mmol/L FeSO4 and 2.5 mmol/L NaClO for 96 h can form a uniform goethite coating on the surface of quartz sand without causing clogging. At a flow rate of 7.2 mL/min of the injection reagents, arsenic (as Na2HAsO4) and tracer fluorescein sodium to pass through the iron-coated quartz sand column were approximately at 126 and 7 column pore volumes, respectively. The retardation factor of arsenic was 23.0, and the adsorption capacity was 0.11 mol As per mol Fe. In situ arsenic removal from groundwater in an aquifer was achieved by simultaneous injections of As(V) and Fe(II) reagents. Arsenic fixation resulted from a process of adsorption/co-precipitation with fine goethite particles by way of bidentate binuclear complexes. Therefore, the study results indicate that the high arsenic removal efficiency of the in situ aquifer iron coating technology likely resulted from the expanded specific surface area of the small goethite particles, which enhanced arsenic sorption capability and/or from co-precipitation of arsenic on the surface of goethite particles. Copyright © 2015 Elsevier B.V. All rights reserved.

A conceptual review of regional-scale controls on the composition of clastic sediment and the co-evolution of continental blocks and their sedimentary cover.

PubMed

Cox, R; Lowe, D R

1995-01-02

Both sediment recycling and first-cycle input influence the composition of clastic material in sedimentary systems. This paper examines conceptually the roles played by these processes in governing the composition of clastic sediment on a regional scale by outlining the expected effects on sediment composition of protracted sediment recycling and of continuous first-cycle input on a maturing continental block. Generally speaking, long-term recycling tends to enrich sediments in the most chemically and mechanically stable components: quartz in the sand and silt size fractions, and illite among the clay minerals. Sandstones trend towards pure quartz arenites, and mudrocks become more potassic and aluminous. The average grain size of clastic sediment decreases by a combination of progressive attrition of sand grains and ongoing breakdown of primary silicate minerals to finer-grained clay minerals and oxides. Sandstones derived by continuous first-cycle input from an evolving continental crustal source also become increasingly rich in quartz, but in addition become more feldspathic as the proportion of granitic material in the upper continental crust increases during crustal stabilization. Associated mudrocks also become richer in potassium and aluminum, but will have higher K2O/Al2O3 ratios than recycled muds. The average grain size of the sediment may increase with time as the proportion of sand-prone granitic source rocks increases at the expense of more mud-prone volcanic sources. In general, except in instances where chemical weathering is extreme, first-cycle sediments lack the compositional maturity of recycled detritus, and are characterized by the presence of a variety of primary silicate minerals. Sedimentary systems are not usually completely dominated by either recycling or first-cycle detritus. Generally, however, sedimentary systems associated with the earliest phases of formation and accretion of continental crust are characterized by first-cycle input from igneous and metamorphic rocks, whereas those associated with more mature cratons tend to be dominated by recycled sedimentary material.

Engineering solutions to improve the removal of fecal indicator bacteria by bioinfiltration systems during intermittent flow of stormwater.

PubMed

Mohanty, Sanjay K; Torkelson, Andrew A; Dodd, Hanna; Nelson, Kara L; Boehm, Alexandria B

2013-10-01

Bioinfiltration systems facilitate the infiltration of urban stormwater into soil and reduce high flow events and flooding. Stormwater carries a myriad of pollutants including fecal indicator bacteria (FIB). Significant knowledge gaps exist about the ability of bioinfiltration systems to remove and retain FIB. The present study investigates the ability of model, simplified bioinfiltration systems containing quartz sand and iron oxide-coated quartz sand (IOCS) to remove two FIB (Enterococcus faecalis and Escherichia coli) suspended in synthetic stormwater with and without natural organic matter (NOM) as well as the potential for accumulated FIB to be remobilized during intermittent flow. The experiments were conducted in two phases: (1) the saturated columns packed with either sand or IOCS were contaminated by injecting stormwater with bacteria followed by injection of sterile stormwater and (2) the contaminated columns were subjected to intermittent infiltration of sterile stormwater preceded by a pause during which columns were either kept saturated or drained by gravity. During intermittent flow, fewer bacteria were released from the saturated column compared to the column drained by gravity: 12% of attached E. coli and 3% of attached Ent. faecalis were mobilized from the drained sand column compared to 3% of attached E. coli and 2% attached Ent. faecalis mobilized from the saturated sand column. Dry and wet cycles introduce moving air-water interfaces that can scour bacteria from grain surfaces. During intermittent flows, less than 0.2% of attached bacteria were mobilized from IOCS, which bound both bacteria irreversibly in the absence of NOM. Addition of NOM, however, increased bacterial mobilization from IOCS: 50% of attached E. coli and 8% of attached Ent. faecalis were released from IOCS columns during draining and rewetting. Results indicate that using geomedia such as IOCS that promote irreversible attachment of bacteria, and maintaining saturated condition, could minimize the mobilization of previous attached bacteria from bioinfiltration systems, although NOM may significantly decrease these benefits.

Marine mesocosm bacterial colonisation of volcanic ash

NASA Astrophysics Data System (ADS)

Witt, Verena; Cimarelli, Corrado; Ayris, Paul; Kueppers, Ulrich; Erpenbeck, Dirk; Dingwell, Donald; Woerheide, Gert

2015-04-01

Volcanic eruptions regularly eject large quantities of ash particles into the atmosphere, which can be deposited via fallout into oceanic environments. Such fallout has the potential to alter pH, light and nutrient availability at local scales. Shallow-water coral reef ecosystems - "rainforests of the sea" - are highly sensitive to disturbances, such as ocean acidification, sedimentation and eutrophication. Therefore, wind-delivered volcanic ash may lead to burial and mortality of such reefs. Coral reef ecosystem resilience may depend on pioneer bacterial colonisation of the ash layer, supporting subsequent establishment of the micro- and ultimately the macro-community. However, which bacteria are involved in pioneer colonisation remain unknown. We hypothesize that physico-chemical properties (i.e., morphology, mineralogy) of the ash may dictate bacterial colonisation. The effect of substrate properties on bacterial colonisation was tested by exposing five substrates: i) quartz sand ii) crystalline ash (Sakurajima, Japan) iii) volcanic glass iv) carbonate reef sand and v) calcite sand of similar grain size, in controlled marine coral reef aquaria under low light conditions for six months. Bacterial communities were screened every month by Automated Ribosomal Intergenic Spacer Analysis of the 16S-23S rRNA Internal Transcribed Spacer region. Multivariate statistics revealed discrete groupings of bacterial communities on substrates of volcanic origin (ash and glass) and reef origin (three sands). Analysis of Similarity supported significantly different communities associated with all substrates (p=0.0001), only quartz did not differ from both carbonate and calcite sands. The ash substrate exhibited the most diverse bacterial community with the most substrate-specific bacterial operational taxonomic units. Our findings suggest that bacterial diversity and community composition during colonisation of volcanic ash in a coral reef-like environment is controlled by the physico-chemical composition of the substrate. Knowledge on pioneer bacterial colonisation may increase our understanding on the resilience of coral reefs to natural "catastrophes", such as volcanic ash fallout.

Evaluation of an improved prototype mini-baghouse to control the release of respirable crystalline silica from sand movers.

PubMed

Alexander, Barbara M; Esswein, Eric J; Gressel, Michael G; Kratzer, Jerry L; Feng, H Amy; Miller, Arthur L; Cauda, Emanuele; Heil, Graeham

2018-01-01

The OSHA final rule on respirable crystalline silica (RCS) will require hydraulic fracturing companies to implement engineering controls to limit workers' exposure to RCS. RCS is generated by pneumatic transfer of quartz-containing sand during hydraulic fracturing operations. Chronic inhalation of RCS can lead to serious disease, including silicosis and lung cancer. NIOSH research identified at least seven sources where RCS aerosols were generated at hydraulic fracturing sites. NIOSH researchers developed an engineering control to address one of the largest sources of RCS aerosol generation, RCS escaping from thief hatches on the top of sand movers. The control, the NIOSH Mini-Baghouse Retrofit Assembly (NMBRA), mounts on the thief hatches. Unlike most commercially available engineering controls, the NMBRA has no moving parts and requires no power source. This article details the results of an evaluation of generation 3 of the NMBRA at a sand mine in Arkansas from May 19-21, 2015. During the evaluation, 168 area air samples were collected at 12 locations on and around a sand mover with and without the NMBRA installed. Analytical results for respirable dust and RCS indicated the use of the NMBRA effectively reduced concentrations of both respirable dust and RCS downwind of the thief hatches. Reductions of airborne respirable dust were estimated at 99+%; reductions in airborne RCS ranged from 98-99%. Analysis of bulk samples of the dust showed the likely presence of freshly fractured quartz, a particularly hazardous form of RCS. Use of an improved filter fabric and a larger area of filter cloth led to substantial improvements in filtration and pressures during these trials, as compared to the generation 2 NMBRA. Planned future design enhancements, including a weather cover, will increase the performance and durability of the NMBRA. Future trials are planned to evaluate the long-term operability of the technology.

Marine Mesocosm Bacterial Colonisation of Volcanic Ash

NASA Astrophysics Data System (ADS)

Witt, V.; Cimarelli, C.; Ayris, P. M.; Kueppers, U.; Erpenbeck, D.; Dingwell, D. B.; Woerheide, G.

2014-12-01

Explosive volcanic eruptions regularly eject large quantities of ash particles into the atmosphere, which can be deposited via fallout into oceanic environments. Such fallout has the potential to alter pH, light and nutrient availability at local or regional scales. Shallow-water coral reef ecosystems - "rainforests of the sea" - are highly sensitive to disturbances, such as ocean acidification, sedimentation and eutrophication. Therefore, ash deposition may lead to burial and mortality of such reefs. Coral reef ecosystem resilience may depend on pioneer bacterial colonisation of the ash layer, supporting subsequent establishment of the micro- and ultimately the macro-community. However, it is currently unknown which bacteria are involved in pioneer colonisation. We hypothesize that physico-chemical properties (i.e., morphology, chemistry, mineralogy) of the ash may dictate bacterial colonisation. We have tested the effect of substrate properties on bacterial diversity and abundance colonising five substrates: i) quartz sand ii) crystalline ash from the Sakurajima volcano (Japan) iii) volcanic glass iv) carbonate reef sand and v) calcite sand of similar grain size - by incubation in a controlled marine mesocosm (coral reef aquarium) under low light conditions for three months. Bacterial communities were screened every month by Automated Ribosomal Intergenic Spacer Analysis of the 16S-23S rRNA Internal Transcribed Spacer region. Multivariate statistics revealed discrete groupings of bacterial communities on substrates of volcanic origin (ash and glass) and reef origin (three sands). Analysis Of Similarity supports significantly different communities associated with all substrates (p=0.0001), only quartz did not differ from both carbonate and calcite sands. The ash substrate exhibited the most diverse bacterial community and carried the most substrate-specific bacterial operational taxonomic units. Our findings suggest that bacterial diversity and community composition during colonisation of volcanic ash in a coral reef-like environment is controlled by the physico-chemical composition of the substrate. Knowledge on pioneer bacterial colonisation may increase our understanding on the resilience of coral reefs to natural "catastrophes", such as volcanic ash fallout.

Assessing the transport potential of polymeric nanocapsules developed for crop protection.

PubMed

Petosa, Adamo Riccardo; Rajput, Faraz; Selvam, Olivia; Öhl, Carolin; Tufenkji, Nathalie

2017-03-15

Nanotechnology is increasingly important in the agricultural sector, with novel products being developed to heighten crop yields and increase pesticide efficacy. Herein, the transport potential of different polymeric nanocapsules (nCAPs) developed as pesticide delivery vehicles was assessed in model soil systems. The nCAPs examined are (i) poly(acrylic acid)-based (nCAP1), (ii) poly(methacrylic acid)-ran-poly(ethyl acrylate) copolymer-based (nCAP2), (iii) poly(methacrylic acid-ran-styrene) copolymer-based (nCAP3), and (iv) poly(methacrylic acid-ran-butylmethacrylate)-based (nCAP4). nCAP mobility was examined in columns packed with agricultural loamy sand saturated with artificial porewater containing Ca 2+ and Mg 2+ cations (10 mM ionic strength, pH 6 and 8). Furthermore, the impact of (i) cation species, (ii) sand type, and (iii) ammonium polyphosphate fertilizer on the transport potential of a nanoformulation combining nCAP4 capsules and the pyrethroid bifenthrin (nCAP4-BIF) was examined and compared to a commercial bifenthrin formulation (Capture ® LFR). Although nCAP4-BIF and Capture ® LFR formulations were highly mobile in quartz sand saturated with 10 mM NaNO 3 (≥95% elution), they were virtually immobile in the presence of 10% ammonium polyphosphate fertilizer. The presence of Ca 2+ and Mg 2+ did not hinder nCAP4-BIF elution in quartz sand saturated with 10 mM standard CIPAC D synthetic porewater; however, limited Capture ® LFR transport (<10% elution) was observed under the same conditions. Capture ® LFR also exhibited limited mobility in the presence or absence of fertilizer in loamy sand saturated with divalent salt solutions, whereas nCAP4-BIF exhibited increased elution with time and enhanced transport upon the addition of fertilizer. Overall, nCAP4 is a promising delivery vehicle in pyrethroid nanoformulations such as nCAP4-BIF. Copyright © 2016 Elsevier Ltd. All rights reserved.

A High Resolution Look at Black Sand Particles from Sand Dunes of Saudi Arabia Using Electron Microscopy

NASA Astrophysics Data System (ADS)

Hussain, M. M.; Aburizaiza, O. S.; Siddique, A.; Hershey, D. L.; Guerrieri, D. A.; Qurashi, J.; Abbass, M.; Blake, D. R.; Khwaja, H. A.

2013-12-01

Particulate air pollution is a problem of health concern. The microscopic make-up of different varieties of sand particles found and collected at a sand dune site in Badr, Saudi Arabia has been determined. Primary emphasis is given to the use of multiple high resolution electron microscopy (viz., Scanning Electron Microscopy with Energy Dispersive X-ray spectrometry (SEM/EDS) and Laser Scanning Microscopy (LSM)) to study the morphologies, emission source types, size, and elemental composition of the particles, and to evaluate the presence of ';coatings or contaminants' adsorbed or carried on by the black sand particles. White sand contains natural coarse particles associated with wind-blown releases from crustal surfaces, weathering of an igneous/metamorphic rock source, and volcanic activities. Silicates (alumino-silicates) and quartz (clear, milky, rose) dominate white sand and rest appears to contain calcite, olivine, feldspar, and magnetite. Black sand particles exhibit very different morphologies and microstructures (surface roughness) compared with white sand and volcanic ash. Morphological analyses have shown that the black sand contain ultrafine particles. Black sand is strongly magnetic, which indicates the mineral magnetite (strongly magnetic) or elemental iron. Iron, C, O, Ti, Si, V, and S particles dominate the black sand. Natural and anthropogenic sources have been implicated for the observed particles. Analysis revealed that the surface of white sand particles is mainly covered with the fine particles. It is known that emissions from combustion contain carbon soot and other contaminants that are easily absorbed by soil particles during a long-range transport.

Origin of the Sinai-Negev erg, Egypt and Israel: mineralogical and geochemical evidence for the importance of the Nile and sea level history

USGS Publications Warehouse

Muhs, Daniel R.; Roskin, Joel; Tsoar, Haim; Skipp, Gary; Budahn, James R.; Sneh, Amihai; Porat, Naomi; Stanley, Jean-Daniel; Katra, Itzhak; Blumberg, Dan G.

2013-01-01

The Sinai–Negev erg occupies an area of 13,000 km2 in the deserts of Egypt and Israel. Aeolian sand of this erg has been proposed to be derived from the Nile Delta, but empirical data supporting this view are lacking. An alternative source sediment is sand from the large Wadi El Arish drainage system in central and northern Sinai. Mineralogy of the Negev and Sinai dunes shows that they are high in quartz, with much smaller amounts of K-feldspar and plagioclase. Both Nile Delta sands and Sinai wadi sands, upstream of the dunes, also have high amounts of quartz relative to K-feldspar and plagioclase. However, Sinai wadi sands have abundant calcite, whereas Nile Delta sands have little or no calcite. Overall, the mineralogical data suggest that the dunes are derived dominantly from the Nile Delta, with Sinai wadi sands being a minor contributor. Geochemical data that proxy for both the light mineral fraction (SiO2/10–Al2O3 + Na2O + K2O–CaO) and heavy mineral fraction (Fe2O3–MgO–TiO2) also indicate a dominant Nile Delta source for the dunes. Thus, we report here the first empirical evidence that the Sinai–Negev dunes are derived dominantly from the Nile Delta. Linkage of the Sinai–Negev erg to the Nile Delta as a source is consistent with the distribution of OSL ages of Negev dunes in recent studies. Stratigraphic studies show that during the Last Glacial period, when dune incursions in the Sinai–Negev erg began, what is now the Nile Delta area was characterized by a broad, sandy, minimally vegetated plain, with seasonally dry anastomosing channels. Such conditions were ideal for providing a ready source of sand for aeolian transport under what were probably much stronger glacial-age winds. With the post-glacial rise in sea level, the Nile River began to aggrade. Post-glacial sedimentation has been dominated by fine-grained silts and clays. Thus, sea level, along with favorable climatic conditions, emerges as a major influence on the timing of dune activity in the Sinai–Negev erg, through its control on the supply of sand from the Nile Delta. The mineralogy of the Sinai–Negev dunes is also consistent with a proposed hypothesis that these sediments are an important source of loess in Israel.

Effects of Aging Quartz Sand and Hanford Site Sediment with Sodium Hydroxide on Radionuclide Sorption Coefficients and Sediment Physical and Hydrologic Properties: Final Report for Subtask 2a

DOE Office of Scientific and Technical Information (OSTI.GOV)

DI Kaplan; JC Ritter; KE Parker

1998-12-04

Column and batch experiments were conducted in fiscal year 1998 at Pacific Northwest National Laboratory to evaluate the effect of varying concentrations of NaOH on the sorptive, physical, and hydraulic properties of two media, a quartz sand and a composite subsurface sediment from the 200-East Area of the Hanford Site. The NaOH solutions were used as a simplified effluent from a low-activity glass waste form. These experiments were conducted over a limited (O-to 10-month) contact time, with respect to the 10,000-to 100,000-year scenarios described in the Immobilized Low-Activity Waste- Performance Assessment (ILAW-PA). Wheq these two solids were put in contactmore » with the NaOH solutions, dissolution was evident by a substantial increase in dissolved Si concentrations in the leachates. Incremental increases in NaOH con- centrations, resulted in corresponding increases in Si concentrations. A number of physical and hydraulic properties also changed as the NaOH concentrations were changed. It was observed that quartz sand was less reactive than the composite sediment. Further, moisture- retention measurements were made on the quartz sand and composite sedimen$ which showed that the NaOH-treated solids retained more water than the non-NaOH-treated solids. Because the other chemical, physical, and hydraulic measurements did not change dramatically after the high-NaOH treatments, the greater moisture retention of the high-NaOH treatments was attributed to a "salt effect" and not to the formation of small particles during the dissolution (weathering). The distribution coefficients (IQ) for Cs and Sr were measured on the NaOH-treated sediments, with decreases from -3,000 to 1,000 and 1,300 to 300 mL/g noted, respectively, at the 0.01-to 1.O-M NaOH levels. There was no apparent trend for the Sr & values with contact time. The lack of such a trend sug- gests that dissolution of sediment particles is not controlling the drop in IQ rather, it is the competition of the added Na in the various treatment solutions. It is clear from these experiments that the background chemistry of the waste-glass Ieachate is likely to have a significant effect on the hydrology and radionuclide geochemistry in the near-field environment of the ILAW.' These experiments provided an important f~st approximation of several chemical and physical processes. Future research, together with the data presented in this repo~ will provide important guidance for the selection of near-field hydraulic and geochemical input data for the ILAW-PA.« less

Synthesis and characterization of mangan oxide coated sand from Capkala kaolin

NASA Astrophysics Data System (ADS)

Destiarti, Lia; Wahyuni, Nelly; Prawatya, Yopa Eka; Sasri, Risya

2017-03-01

Synthesis and characterization of mangan oxide coated sand from quartz sand fraction of Capkala kaolin has been conducted. There were two methods on synthesis of Mangan Oxide Coated Sand (MOCS) from Capkala Kaolin compared in this research. Characterization of MOCS was done by using Scanning Electron Microscope/Energy Dispersive X-Ray Spectrometer (SEM/EDX) and X-Ray Diffraction (XRD). The MOCS was tested to reduce phosphate in laundry waste. The result showed that the natural sand had bigger agregates and a relatively uniform structural orientation while both MOCS had heterogen structural orientation and manganese oxide formed in cluster. Manganese in first and second methods were 1,93% and 2,63%, respectively. The XRD spectrum showed clear reflections at 22,80°, 36,04°, 37,60° and a broad band at 26,62° (SiO2). Based on XRD spectrum, it can be concluded that mineral constituents of MOCS was verified corresponding to pyrolusite (MnO2). The former MOCS could reduce almost 60% while the later could reduce 70% phosphate in laundry waste.

Detrital minerals from source to sink : tracing Orange River sand from Lesotho to Angola

NASA Astrophysics Data System (ADS)

Garzanti, Eduardo; Vermeesch, Pieter; Andò, Sergio; Resentini, Alberto; Vezzoli, Giovanni; Lustrino, Michele; Padoan, Marta; Pereira, Alcides

2015-04-01

Quantitative provenance analysis based on high-resolution bulk-petrography and heavy-mineral data on beach and dune sands, integrated with detrital-zircon geochronology and chemical analyses of pyroxene, garnet and staurolite, demonstrates that sand carried by the Orange River and derived from Lesotho and South Africa is carried by powerful and persistent longshore currents as far as southern Angola (Garzanti et al., 2014a). This is the longest cell of littoral sand transport documented so far on Earth, and a great test case for investigating physical controls on sand texture and composition. We have monitored textural, mineralogical and geochemical variability of beach and eolian-dune sands along a 1750 km stretch of the Atlantic coast of southern Africa by using an integrated set of techniques, including image analysis, laser granulometry, optical microscopy, Raman spectroscopy and bulk-sediment geochemistry (Garzanti et al., 2014b). Our results contrast with previous reports that feldspars and volcanic detritus break down during transport, that sand grains are rounded rapidly in shallow-marine environments, and that quartzose sands may be produced by physical processes alone. We demonstrate that basaltic rock fragments and pyroxenes, traditionally believed to be rapidly destroyed, survive healthily the 4000 km-long multistep hazardous journey from Lesotho volcanic highlands to Angola. Feldspar abundance remains remarkably constant from the Orange mouth to southern Angola, and quartz increases only very slightly, possibly as a result of local recycling. Among sedimentary and metasedimentary rock fragments, unconsolidated or strongly foliated types are readily comminuted when they enter the high-energy marine environment, but cemented sandstone/siltstone grains can survive the travel from the Karoo Basin of South Africa to northern Namibia and beyond. No detrital mineral displays a significant increase in grain roundness after 300-350 km of longshore transport in high-energy littoral environments from the Orange mouth to south of the Namib Erg, but all minerals get rapidly rounded after passing into the Namib dunefield. Pyroxene and opaques get rounded faster than harder quartz and garnet, but sand mineralogy remains unchanged. Excepting strong transient selective-entrainment effects, physical processes are unable to modify sand composition significantly. Mechanical wear and selective mechanical breakdown can thus be largely neglected in provenance studies even in the case of ultra-long distance transport in high-energy environments dominated by waves or winds. This is particularly true for ancient sandstones, where chemical dissolution during diagenesis exerts an incomparably stronger control on mineralogical assemblages. REFERENCES Garzanti. E., Vermeesch, P., Andò, S., Lustrino, M., Padoan, M., Vezzoli, G., 2014a. Ultra-long distance littoral transport of Orange sand and provenance of the Skeleton Coast Erg (Namibia). Marine Geology, 357, 25-36. Garzanti, E., Resentini, A., Andò, S., Vezzoli, G., Vermeesch, P., 2014b. Physical controls on sand composition and relative durability of detrital minerals during long-distance littoral and eolian transport (coastal Namibia). Sedimentology, DOI: 10.1111/sed.12169.

DOE/SC0001389 Final technical report: Investigation of uranium attenuation and release at column and pore scales in response to advective geochemical gradients

DOE Office of Scientific and Technical Information (OSTI.GOV)

Savage, Kaye S.; Zhu, Wenyi; Barnett, Mark O.

2013-05-13

Experimental approach Column experiments were devised to investigate the role of changing fluid composition on mobility of uranium through a sequence of geologic media. Fluids and media were chosen to be relevant to the ground water plume emanating from the former S-3 ponds at the Oak Ridge Integrated Field Research Challenge (ORIFC) site. Synthetic ground waters were pumped upwards at 0.05 mL/minute for 21 days through layers of quartz sand alternating with layers of uncontaminated soil, quartz sand mixed with illite, quartz sand coated with iron oxides, and another soil layer. Increases in pH or concentration of phosphate, bicarbonate, ormore » acetate were imposed on the influent solutions after each 7 pore volumes while uranium (as uranyl) remained constant at 0.1mM. A control column maintained the original synthetic groundwater composition with 0.1mM U. Pore water solutions were extracted to assess U retention and release in relation to the advective ligand or pH gradients. Following the column experiments, subsamples from each layer were characterized using microbeam X-ray absorption spectroscopy (XANES) in conjunction with X-ray fluorescence mapping and compared to sediment core samples from the ORIFC, at SSRL Beam Line 2-3. Results U retention of 55-67mg occurred in phosphate >pH >control >acetate >carbonate columns. The mass of U retained in the first-encountered quartz layer in all columns was highest and increased throughout the experiment. The rate of increase in acetate- and bicarbonate-bearing columns declined after ligand concentrations were raised. U also accumulated in the first soil layer; the pH-varied column retained most, followed by the increasing-bicarbonate column. The mass of U retained in the upper layers was far lower. Speciation of U, interpreted from microbeam XANES spectra and XRF maps, varied within and among the columns. Evidence of minor reduction to U(IV) was observed in the first-encountered quartz layer in the phosphate, bicarbonate, and pH columns while only U(VI) was observed in the control and acetate columns. In the soil layer, the acetate and bicarbonate columns both indicate minor reduction to U(IV), but U(VI) predominated in all columns. In the ORIFC soils, U was consistently present as U(VI); sorption appears to be the main mechanism of association for U present with Fe and/or Mn, while U occurring with P appears in discrete particles consistent with a U mineral phase. U in soil locations with no other elemental associations shown by XRF are likely uranium oxide phases.« less

Production of mineral aggregates in quartz tumbling experiments

NASA Astrophysics Data System (ADS)

Nørnberg, Per; Finster, Kai; Pall Gunnlaugsson, Haraldur; Knak Jensen, Svend; Merrison, Jonathan Peter

2013-04-01

Introduction Tumbling experiments with quartz sand with the purpose of tracing the effect of broken bonds in mineral surfaces resulted in an unexpected production of aggregates. These aggregates are a few microns in diameter, spherical and resembling tiny white "snowballs." Particle comminution by aeolian and other natural weathering processes are known in soil science and is often seen as an increase of fine particles towards the top of soil profiles (Nørnberg, P. 1987, 1988, 2002, J.S. Wright 2007). When mineral grains collide in aeolian processes they break up along weakness zones in the crystal lattice. This mechanism causes broken bonds between atoms in the crystal lattice and results in reactive groups in the mineral surface. This mechanism provides the background for experiments to investigate the oxidation processes of magnetite on the planet Mars. The primary magnetic iron oxide phase on Mars is to day known to be magnetite and the colour of the dust on Mars is most likely due to hematite. To investigate if the oxidation process could take place without going over dissolution and precipitation in water, experiments with tumbling of quartz grains in sealed glass containers along with magnetite were started. The idea was that activated bonds at the surface of quartz could oxidize magnetite and convert it to hematite over time. This proved to be the case (Merrison, J.P. et al. 2010). However, in these experiments we observed the formation of the white aggregates which has been the subject of the study that we present here. Results of tumbling experiments Commercially available quarts (Merck) was sieved to obtain the fraction between 125 and 1000 µm. This fraction was tumbled in glass containers for months and resulted in production of a significant amount of fine grained material (Merrison, J.P et al. 2010). A part of this fine fraction consists of the "snowball"-like aggregates which is a fragile element with relatively high specific surface. The physical properties of these structures will be discussed in this paper. Nørnberg, P. 1977: Soil Profile Development in Sands of Varying Age in Vendsyssel, Denmark. Catena, 4, 165-179. Nørnberg, P. 1980: Mineralogy of a podzol formed in sandy materials in Northern Denmark. Geoderma, 24, 25-43. Nørnberg, P. 2002: Particle comminution and aeolian addition in young dune sand soils. Transactions, 17th World Congress of Soil Science, Bangkok, Thailand, Symp. 25, pp. 9. Janet S. Wright, Janet S. 2007: An overview of the role of weathering in the production of quartz silt Sedimentary Geology, 202, 337-351 Merrison, J.P., Gunnlaugsson, H.P., Nørnberg, P., Jensen, A.E., Rasmussen, K.R. 2007: Determination of the Wind Induced Detachment Threshold for Granular Material on Mars using Wind Tunnel Simulations. Icarus, 191, 568-580.

Impacts into quartz sand: Crater formation, shock metamorphism, and ejecta distribution in laboratory experiments and numerical models

NASA Astrophysics Data System (ADS)

Wünnemann, Kai; Zhu, Meng-Hua; Stöffler, Dieter

2016-10-01

We investigated the ejection mechanics by a complementary approach of cratering experiments, including the microscopic analysis of material sampled from these experiments, and 2-D numerical modeling of vertical impacts. The study is based on cratering experiments in quartz sand targets performed at the NASA Ames Vertical Gun Range. In these experiments, the preimpact location in the target and the final position of ejecta was determined by using color-coded sand and a catcher system for the ejecta. The results were compared with numerical simulations of the cratering and ejection process to validate the iSALE shock physics code. In turn the models provide further details on the ejection velocities and angles. We quantify the general assumption that ejecta thickness decreases with distance according to a power-law and that the relative proportion of shocked material in the ejecta increase with distance. We distinguish three types of shock metamorphic particles (1) melt particles, (2) shock lithified aggregates, and (3) shock-comminuted grains. The agreement between experiment and model was excellent, which provides confidence that the models can predict ejection angles, velocities, and the degree of shock loading of material expelled from a crater accurately if impact parameters such as impact velocity, impactor size, and gravity are varied beyond the experimental limitations. This study is relevant for a quantitative assessment of impact gardening on planetary surfaces and the evolution of regolith layers on atmosphereless bodies.

Aerolian erosion, transport, and deposition of volcaniclastic sands among the shifting sand dunes, Christmas Lake Valley, Oregon: TIMS image analysis

NASA Technical Reports Server (NTRS)

Edgett, Kenneth S.; Ramsey, Michael S.; Christensen, Philip R.

1995-01-01

Remote sensing is a tool that, in the context of aeolian studies, offers a synoptic view of a dune field, sand sea, or entire desert region. Blount et al. (1990) presented one of the first studies demonstrating the power of multispectral images for interpreting the dynamic history of an aeolian sand sea. Blount's work on the Gran Desierto of Mexico used a Landsat TM scene and a linear spectral mixing model to show where different sand populations occur and along what paths these sands may have traveled before becoming incorporated into dunes. Interpretation of sand transport paths and sources in the Gran Desierto led to an improved understanding of the origin and Holocene history of the dunes. With the anticipated advent of the EOS-A platform and ASTER thermal infrared capability in 1998, it will become possible to look at continental sand seas and map sand transport paths using 8-12 mu m bands that are well-suited to tracking silicate sediments. A logical extension of Blount's work is to attempt a similar study using thermal infrared images. One such study has already begun by looking at feldspar, quartz, magnetite, and clay distributions in the Kelso Dunes of southern California. This paper describes the geology and application of TIMS image analysis of a less-well known Holocene dune field in south central Oregon using TIMS data obtained in 1991.

Experimental study on mix proportion of fiber reinforced cementitious composites

NASA Astrophysics Data System (ADS)

Jia, Yi; Zhao, Renda; Liao, Ping; Li, Fuhai; Yuan, Yuan; Zhou, Shuang

2017-10-01

To study the mechanical property of fiber reinforced cementations composites influenced by the fiber length, quartz sand diameter, matrix of water cement ratio, volume fraction of fiber and magnesium acrylate solution. Several 40×40×160 mm standard test specimens, "8" specimens and long "8" specimens and 21 groups of fiber concrete specimens were fabricated. The flexural, compressive and uniaxial tensile strength were tested by using the bending resistance, compression resistance and electronic universal testing machine. The results show that flexural and compressive strength of fiber reinforced cementations composites increases along with the increase of quartz sand diameter, with the growth of the PVA fiber length increases; When the water-binder ratio is 0.25 and powder-binder ratio is 0.3, the PVA fiber content is 1.5% of the mass of cementations materials, there is a phenomenon of strain hardening; The addition of magnesium acrylate solution reduces the tensile strength of PVA fiber reinforced cementations composites, the tensile strength of the specimens in the curing age of 7d is decreased by about 21% and the specimens in curing age of 28d is decreased by more than 50%.

Soda-based glass fabricated from Thailand quartz sands doped with silver compound

NASA Astrophysics Data System (ADS)

Won-in, Krit; Dararutana, Pisutti

2012-10-01

Yellow colored glass which used for luxury art glass in ancient time was fabricated by the addition of silver compound into the molten glass. It was proved that it was actually silver nanoparticle technology. In this work, the SiO2-(Na2O,K2O)-CaO-B2O3-Al2O3-MgO glass system was prepared in the laboratory scale based on local quartz sands from Trat Province, eastern area of Thailand as the silica raw material. Various concentrations of silver nitrate were added. After the complete conventional melting process, the bubble-free yellow glasses were yielded. Physical and optical properties such as density, refractive index and optical absorption spectra were measured. Scanning electron microscope coupled with energy dispersive spectroscopy was carried out to study their morphology. The refractive indices and densities were increased as the increase of the silver contents. Electron micrographs showed the presence of silver nanoparticle in the glass matrix. UV-VIS spectra were in good agreement with that found from SEM measurements and corresponded with the universally accepted. It was also showed that the more brilliance on the surface of the glass products was obtained after firing with a gas torch.

Optical dating of eolian deposits since the last interglacial along the northern margin of the Chinese Loess Plateau

NASA Astrophysics Data System (ADS)

Lü, Tongyan; Sun, Jimin; Gong, Zhijun

2018-04-01

Understanding the chronology of eolian sand-loess-paleosol sequences along the northern margin of the Chinese Loess Plateau (CLP) is crucial for comprehending climate change and the advance and retreat of the adjacent Mu Us desert. In this study, a sand-loess-soil sequence from the northern margin of the CLP was studied by applying the single aliquot regenerative (SAR) protocol to quartz grains, and the multi-elevated-temperature post-IR IRSL (MET-pIRIR) protocol to K-feldspar grains. For equivalent dose (De) determination, 63-90 μm quartz and K-feldspar grains were used. Our results indicate that the MET-pIRIR ages of K-feldspar grains in this sequence range from 94.4 ± 7.0 ka to 148.3 ± 13.3 ka for the last interglacial paleosol (S1); for the upper part of the section, quartz-based SAR-OSL dating was used, yielding ages spanning from 5.8 ± 0.4 ka to 35.9 ± 4.1 ka. After cross-checking these results with previously-reported isochron OSL and TL ages, the reliability of the MET-pIRIR protocol when applied to the last interglacial paleosol was confirmed. Based on a new OSL chronology of the Shimao profile, the studied eolian deposits can be broadly correlated with the last glacial-interglacial cycle, but their dating also points to sedimentary hiatuses occurring at 94.4 ka, 35.9 ka and 5.8 ka, due most probably to strong wind erosion caused by intensified cold-dry winter monsoonal circulations during the last glacial maxima.

Silica dust exposures during selected construction activities.

PubMed

Flanagan, Mary Ellen; Seixas, Noah; Majar, Maria; Camp, Janice; Morgan, Michael

2003-01-01

This study characterized exposure for dust-producing construction tasks. Eight common construction tasks were evaluated for quartz and respirable dust exposure by collecting 113 personal task period samples for cleanup; demolition with handheld tools; concrete cutting; concrete mixing; tuck-point grinding; surface grinding; sacking and patching concrete; and concrete floor sanding using both time-integrating filter samples and direct-reading respirable dust monitors. The geometric mean quartz concentration was 0.10 mg/m(3) (geometric standard deviation [GSD]=4.88) for all run time samples, with 71% exceeding the threshold limit value. Activities with the highest exposures were surface grinding, tuck-point grinding, and concrete demolition (GM[GSD] of 0.63[4.12], 0.22[1.94], and 0.10[2.60], respectively). Factors recorded each minute were task, tool, work area, respiratory protection and controls used, estimated cross draft, and whether anyone nearby was making dust. Factors important to exposure included tool used, work area configuration, controls employed, cross draft, and in some cases nearby dust. More protective respirators were employed as quartz concentration increased, although respiratory protection was found to be inadequate for 42% of exposures. Controls were employed for only 12% of samples. Exposures were reduced with three controls: box fan for surface grinding and floor sanding, and vacuum/shroud for surface grinding, with reductions of 57, 50, and 71%, respectively. Exposures were higher for sweeping compound, box fan for cleanup, ducted fan dilution, and wetted substrate. Construction masons and laborers are frequently overexposed to silica. The usual protection method, respirators, was not always adequate, and engineering control use was infrequent and often ineffective.

The Influence of Hydrophilic Interactions on the Sorption and Mobility of Naproxen at Environmentally-Relevant Concentrations

NASA Astrophysics Data System (ADS)

Muller, K.; Ramsburg, C. A.

2011-12-01

Managed underground storage of reclaimed wastewater is currently one viable option for meeting increasing demands on water resources, yet the attenuation of many emerging contaminants within the subsurface environment is not well understood. Pharmaceuticals are of particular concern due to the rapid increase in development and use of these compounds, observations of incomplete removal during wastewater treatment, and emerging concerns over ecosystem effects. Assessment of the subsurface attenuation of pharmaceuticals is difficult because the compounds are polar, pH-active, and present at low-concentration (ng/L). Predictions of sorption that only consider hydrophobic interactions with soil organic matter may not fully describe the extent to which reversible sequestration influences pharmaceutical attenuation. In fact, hydrophilic interactions (i.e. ion exchange, cation-induced sorption, hydrogen bonding, etc) may represent important contributions to total sorption, especially when aqueous solutes are present at low concentration. Here we assess the sorption of naproxen - an acidic pharmaceutical - to three subsurface materials using equilibrium batch experiments and 1-d column experiments. Subsurface materials evaluated include Ottawa sand (quartz with negligible organic carbon and negligible iron oxide), Aplite sand (quartz and feldspar with negligible organic carbon, 0.2% wt iron oxide), and a Hinckley series silty-sand (quartz and feldspar with 0.95% wt organic carbon, and 0.4% wt iron oxides). Sorption of naproxen to the Ottawa sand was negligible and did not result in measurable retardation when naproxen was introduced to the porous medium at a concentration of 275 ng/L. Batch experiments suggest that Aplite sand offers quantifiable interaction (52% of the mass introduced is associated with the solid phase when the aqueous concentration is 1000 ng/L and the solid to liquid ratio is 1.4:1 v/v); however, column data are indicative of markedly less interaction and retardation. Naproxen sorption to the Hinckley series material was considerable (99% of the mass introduced is associated with the solid phase when the aqueous concentration is 1000 ng/L and the solid to liquid ratio is 1:1 v/v). Predictions of naproxen sorption based upon the fraction of organic carbon and the organic-carbon partitioning coefficient (Koc) greatly underestimated the sorption observed in all experiments conducted with the Hinckley series material. Assessment of sorption under 1 mM NaH2PO4 (a sorbant with a strong affinity for hydrophilic sites) suggests that hydrophobic interactions account for approximately 45% of the total interaction. Breakthrough of naproxen (C0 ~ 20 ug/L) was substantially retarded in experiments conducted with the Hinckley material and a thermally-treated Hinckley material (negligible organic carbon). These results highlight the potential role of hydrophilic interactions during the transport and attenuation of acidic pharmaceuticals at solute concentrations typical of water reuse applications.

The effect of chrome adhesion layer on quartz resonator aging.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wessendorf, Kurt O.; Ohlhausen, James Anthony

2011-03-01

This SAND report documents a late start LDRD designed to determine the possible aging effects of a quartz resonator gold adhesion layer. Sandia uses quartz resonators for applications. These applications require a very stable frequency source with excellent aging (low drift) characteristics. These parts are manufactured by one of our qualified vendors outside Sandia Laboratories, Statek Corp. Over the years we, Sandia and the vendor, have seen aging variations that have not been completely explained by the typical mechanisms known in the industry. One theory was that the resonator metallization may be contributing to the resonator aging. This LDRD wouldmore » allow us to test and analyze a group of resonators with known differentiating metallization and via accelerated aging determine if a chrome adhesion layer used to accept the final gold plating may contribute to poor aging. We worked with our main vendor to design and manufacture a set of quartz resonators with a wide range of metallization thickness ratios between the chrome and gold that will allow us determine the cause of this aging and which plating thickness ratios provide the best aging performance while not degrading other key characteristics.« less

Influence of organic matter on the transport of Cryptosporidium parvum oocysts in a ferric oxyhydroxide-coated quartz sand saturated porous medium

USGS Publications Warehouse

Abudalo, R.A.; Ryan, J.N.; Harvey, R.W.; Metge, D.W.; Landkamer, Lee L.

2010-01-01

To assess the effect of organic matter on the transport of Cryptosporidium parvum oocysts in a geochemically heterogeneous saturated porous medium, we measured the breakthrough and collision efficiencies of oocysts as a function of dissolved organic matter concentration in a flow-through column containing ferric oxyhydroxide-coated sand. We characterized the surface properties of the oocysts and ferric oxyhydroxide-coated sand using microelectrophoresis and streaming potential, respectively, and the amount of organic matter adsorbed on the ferric oxyhydroxide-coated sand as a function of the concentration of dissolved organic matter (a fulvic acid isolated from Florida Everglades water). The dissolved organic matter had no significant effect on the zeta potential of the oocysts. Low concentrations of dissolved organic matter were responsible for reversing the charge of the ferric oxyhydroxide-coated sand surface from positive to negative. The charge reversal and accumulation of negative charge on the ferric oxyhydroxide-coated sand led to increases in oocyst breakthrough and decreases in oocyst collision efficiency with increasing dissolved organic matter concentration. The increase in dissolved organic matter concentration from 0 to 20 mg L-1 resulted in a two-fold decrease in the collision efficiency. ?? 2009 Elsevier Ltd.

Investigation of Physico-Chemical Properties of Sand-Lime Products Modified of Diabase Aggregate and Chalcedonite Meal

NASA Astrophysics Data System (ADS)

Dachowski, Ryszard; Komisarczyk, Katarzyna

2017-10-01

In the era of rapid development in the construction industry, particular attention is focused on harmless and natural materials. Some of the best materials for building masonry walls are sand-lime products. Silicates are obtained from a mixture of quartz, sand and a small amount of water. They emerge as a result of the hydrothermal treatment conducted under high pressure and at a temperature of app. 203 °C. Silicates were modified of different kinds of aggregates, glass or plastics, and the content of dry ingredients was changed because of this fact. The paper describes the studies where the combination of diabase aggregate and chalcedonite meal was used. Microstructure of the products was analyzed with the use of mercury intrusion porosimetry, SEM and XRD methods. Variable content of chalcedonite meal changes the internal structure and the physico-chemical properties.

Effects of substrate mineralogy on the biodegradability of fuel components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Apitz, S.E.; Meyers-Schulte, K.J.

1996-11-01

Experiments were carried out to determine the effects of mineralogy on the biodegradability of components of a whole fuel by a soil microbial consortium. Samples of quartz sand (Fischer Sea Sand) and illite clay (API 35) were spiked with marine diesel fuel, aged, slurried, and inoculated, and concentrations of fuel components were monitored over time. To help distinguish biotic from abiotic processes, identical samples were poisoned with mercuric chloride and were run in parallel. While there was a chromatographic and biomarker evidence of n-alkane biodegradation in the sand samples, illite samples showed no evidence of biogenic loss of aliphatic components.more » Polycyclic aromatic hydrocarbons, on the other hand, were lost equivalently on both minerals and in both cases were lost to a much greater extent than were total petroleum hydrocarbons (TPHs). These results suggest that under experimental conditions, illite inhibited the bioavailability of some TPH components to the soil microbial consortium.« less

The Development and Testing of a Prototype Mini-Baghouse to Control the Release of Respirable Crystalline Silica from Sand Movers

PubMed Central

Alexander, Barbara M.; Esswein, Eric J.; Gressel, Michael G.; Kratzer, Jerry L.; Feng, H. Amy; King, Bradley; Miller, Arthur L.; Cauda, Emanuele

2016-01-01

Inhalation of respirable crystalline silica (RCS) is a significant risk to worker health during well completions operations (which include hydraulic fracturing) at conventional and unconventional oil and gas extraction sites. RCS is generated by pneumatic transfer of quartz-containing sand during hydraulic fracturing operations. National Institute for Occupational Safety and Health (NIOSH) researchers identified concentrations of RCS at hydraulic fracturing sites that exceed 10 times the Occupational Safety and Health Administration (OSHA) Permissible Exposure Limit (PEL) and up to 50 times the NIOSH Recommended Exposure Limit (REL). NIOSH research identified at least seven point sources of dust release at contemporary oil and gas extraction sites where RCS aerosols were generated. NIOSH researchers recommend the use of engineering controls wherever they can be implemented to limit the RCS released. A control developed to address one of the largest sources of RCS aerosol generation is the NIOSH mini-baghouse assembly, mounted on the thief hatches on top of the sand mover. This manuscript details the results of a trial of the NIOSH mini-baghouse at a sand mine in Arkansas, November 18 – 21, 2013. During the trial, area air samples were collected at 12 locations on and around a sand mover with and without the mini-baghouse control installed. Analytical results for respirable dust and RCS indicate the use of the mini-baghouse effectively reduced both respirable dust and RCS downwind of the thief hatches. Reduction of airborne respirable dust ranged from 85% to 98%; reductions in airborne RCS ranged from 79% to 99%. A bulk sample of dust collected by the baghouse assembly showed the likely presence of freshly fractured quartz, a particularly hazardous form of RCS. Planned future design enhancements will increase the performance and durability of the mini-baghouse, including an improved bag clamp mechanism and upgraded filter fabric with a modified air-to-cloth ratio. Future trials are planned to determine additional respirable dust and RCS concentration reductions achieved through these design changes. PMID:27003622

Soil Water Content Sensor Response to Organic Matter Content under Laboratory Conditions

PubMed Central

Fares, Ali; Awal, Ripendra; Bayabil, Haimanote K.

2016-01-01

Studies show that the performance of soil water content monitoring (SWCM) sensors is affected by soil physical and chemical properties. However, the effect of organic matter on SWCM sensor responses remains less understood. Therefore, the objectives of this study are to (i) assess the effect of organic matter on the accuracy and precision of SWCM sensors using a commercially available soil water content monitoring sensor; and (ii) account for the organic matter effect on the sensor’s accuracy. Sand columns with seven rates of oven-dried sawdust (2%, 4%, 6%, 8%, 10%, 12% and 18% v/v, used as an organic matter amendment), thoroughly mixed with quartz sand, and a control without sawdust were prepared by packing quartz sand in two-liter glass containers. Sand was purposely chosen because of the absence of any organic matter or salinity, and also because sand has a relatively low cation exchange capacity that will not interfere with the treatment effect of the current work. Sensor readings (raw counts) were monitored at seven water content levels (0, 0.02, 0.04, 0.08, 0.12, 0.18, 0.24, and 0.30 cm3 cm−3) by uniformly adding the corresponding volumes of deionized water in addition to the oven-dry one. Sensor readings were significantly (p < 0.05) affected by the organic matter level and water content. Sensor readings were strongly correlated with the organic matter level (R2 = 0.92). In addition, the default calibration equation underestimated the water content readings at the lower water content range (<0.05 cm3 cm−3), while it overestimated the water content at the higher water content range (>0.05 cm3 cm−3). A new polynomial calibration equation that uses raw count and organic matter content as covariates improved the accuracy of the sensor (RMSE = 0.01 cm3 cm−3). Overall, findings of this study highlight the need to account for the effect of soil organic matter content to improve the accuracy and precision of the tested sensor under different soils and environmental conditions. PMID:27527185

Soil Water Content Sensor Response to Organic Matter Content under Laboratory Conditions.

PubMed

Fares, Ali; Awal, Ripendra; Bayabil, Haimanote K

2016-08-05

Studies show that the performance of soil water content monitoring (SWCM) sensors is affected by soil physical and chemical properties. However, the effect of organic matter on SWCM sensor responses remains less understood. Therefore, the objectives of this study are to (i) assess the effect of organic matter on the accuracy and precision of SWCM sensors using a commercially available soil water content monitoring sensor; and (ii) account for the organic matter effect on the sensor's accuracy. Sand columns with seven rates of oven-dried sawdust (2%, 4%, 6%, 8%, 10%, 12% and 18% v/v, used as an organic matter amendment), thoroughly mixed with quartz sand, and a control without sawdust were prepared by packing quartz sand in two-liter glass containers. Sand was purposely chosen because of the absence of any organic matter or salinity, and also because sand has a relatively low cation exchange capacity that will not interfere with the treatment effect of the current work. Sensor readings (raw counts) were monitored at seven water content levels (0, 0.02, 0.04, 0.08, 0.12, 0.18, 0.24, and 0.30 cm³ cm(-3)) by uniformly adding the corresponding volumes of deionized water in addition to the oven-dry one. Sensor readings were significantly (p < 0.05) affected by the organic matter level and water content. Sensor readings were strongly correlated with the organic matter level (R² = 0.92). In addition, the default calibration equation underestimated the water content readings at the lower water content range (<0.05 cm³ cm(-3)), while it overestimated the water content at the higher water content range (>0.05 cm³ cm(-3)). A new polynomial calibration equation that uses raw count and organic matter content as covariates improved the accuracy of the sensor (RMSE = 0.01 cm³ cm(-3)). Overall, findings of this study highlight the need to account for the effect of soil organic matter content to improve the accuracy and precision of the tested sensor under different soils and environmental conditions.

In situ treatment of arsenic contaminated groundwater by aquifer iron coating: Experimental Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Xianjun; Wang, Yanxin; Pi, Kunfu

In situ arsenic removal from groundwater by an iron coating method has great potential to be a cost effective and simple groundwater remediation technique, especially in rural and remote areas where groundwater is used as the main source of drinking water. The in situ arsenic removal technique was first optimized by simulating arsenic removal in various quartz sand columns under anoxic conditions., Its effectiveness was then evaluated in an actual high-arsenic groundwater environment. The mechanism of arsenic removal by the iron coating was investigated under different conditions using scanning electron microscopy (SEM)/X-ray absorption spectroscopy, an electron microprobe, and Fourier transformationmore » infrared spectroscopy. A 4-step alternative cycle aquifer iron coating method was developed. A continuous injection of 5 mmol/L FeSO4 and 2.5 mmol/L NaClO for 96 hours can create a uniform coating of crystalline goethite on the surface of quartz sand in the columns without causing clogging. At a flow rate of 0.45 cm/min of the injection reagents (vi), the time for arsenic (as Na2HAsO4) to pass through the iron-coated quartz sand column was approximately 35 hours, which was much longer than that for tracer fluorescein sodium (approximately 2 hours). The retardation factor of arsenic was 23, and its adsorption capacity was 0.11 mol As per mol Fe, leading to an excellent arsenic removal. In situ arsenic removal from groundwater in an aquifer was achieved by simultaneous injections of As (V) and Fe (II) reagents. When the arsenic content in the groundwater was 233 μg/L, the aqueous phase arsenic was completely removed with an arsenic adsorption of 0.05 mol As per mol Fe. Arsenic fixation resulted from a process of adsorption/co-precipitation, in which arsenic and iron likely formed the arsenic-bearing iron mineral phases with poor crystallinity by way of bidentate binuclear complexes. Thus, the high arsenic removal efficiency of the technique likely resulted from the expanded specific iron oxide/hydroxide surface area with poor crystallinity and from coprecipitation.« less

Provenance and depositional conditions of Cretaceous-Paleogene boundary sandstones from northeastern Mexico

NASA Astrophysics Data System (ADS)

Rehrmann, Stephanie; Augustsson, Carita; Izaguirre Valdez, Rocio Nereyda; Jenchen, Uwe; Schulte, Peter

2012-12-01

We compare Late Maastrichtian siliciclastic sandstone in northeastern Mexico with those representing the Cretaceous-Paleogene (K-Pg) boundary to reveal differences in provenance and depositional conditions between background sedimentation and K-Pg sand. Lithology and compositional variations are presented for the deep-water Burgos Basin and the shallow-water La Popa Basin. The Late Maastrichtian sandstones in the Burgos Basin have sharp lower contacts, contain abundant trace fossils and are separated by meter-thick marl layers. They represent sporadic mass flows from coastal areas separated by long phases of hemipelagic sedimentation. The K-Pg sandstone layers are amalgamated, contain thin marl intercalations only in the uppermost part and trace fossils are present in the top sandstone layer only. Also this succession represents mass-flow deposits, but the sand may have been deposited during a very short period. The La Popa Basin sandstones represent deltaic sedimentation interrupted by submarine channel deposition during the K-Pg boundary transition with abundant rip-up clasts and bioclasts at the base. The sandstones of the Burgos Basin are quartz to akosic wacke dominated by quartz (> 90%) and some feldspar (< 10%) in calcite cement and matrix. Lithic fragments are rare and dominated by chert and bioclasts. Ultra-stable heavy minerals (ZTR = 50-80) and plutonic quartz grains (ca. 40% of the total quartz population) are particularly common in the K-Pg sandstones. In the Maastrichtian sandstones, metamorphic heavy minerals, particularly chlorite, clinozoisite, and tourmaline (20-50% of the heavy mineral population), and metamorphic quartz (80% of the quartz population) have higher abundances. The La Popa sandstones are subarkose to arkose and arkosic wacke and have a high abundance of feldspar (15-30%) and lithic fragments (5-20%), mainly of siltstone and carbonate. The sandstones from both basins have chemical compositions typical for recycling (Zr/Sc = 12-27 and 17-140 in the Burgos and La Popa Basin, respectively) and influences from mafic source rocks (Th/Sc = 0.4-1.1; Ti/Nb = 350-510). Therefore we suggest that all studied successions share a common provenance with transport of recycled orogenic metasedimentary components from northwestern Mexico and magmatic arc material from western Mexico. Subsequently, longshore currents mixed the detritus with limestone clasts derived from the tectonically active Sierra Madre Oriental, which probably is the cause for compositional changes in the sandstones. Due to increased sediment input from western Mexico at the K-Pg boundary, provenance changes cannot be related to the Chicxulub impact.

Rate laws for water-assisted compaction and stress-induced water-rock interaction in sandstones

NASA Astrophysics Data System (ADS)

Dewers, Thomas; Hajash, Andrew

1995-07-01

Mineral-water interactions under conditions of nonhydrostatic stress play a role in subjects as diverse as ductile creep in fault zones, phase relations in metamorphic rocks, mass redistribution and replacement reactions during diagenesis, and loss of porosity in deep sedimentary basins. As a step toward understanding the fundamental geochemical processes involved, using naturally rounded St. Peter sand, we have investigated the kinetics of pore volume loss and quartz-water reactions under nonhydrostatic, hydrothermal conditions in flow-through reactors. Rate laws for creep and mineral-water reaction are derived from the time rate of change of pore volume, sand-water dissolution kinetics, and (flow rate independent) steady state silica concentrations, and reveal functional dependencies of rates on grain size, volume strain, temperature, effective pressure (confining minus pore pressure), and specific surface areas. Together the mechanical and chemical rate laws form a self-consistent model for coupled deformation and water-rock interaction of porous sands under nonhydrostatic conditions. Microstructural evidence shows a progressive widening of nominally circular and nominally flat grain-grain contacts with increasing strain or, equivalently, porosity loss, and small quartz overgrowths occurring at grain contact peripheries. The mechanical and chemical data suggest that the dominant creep mechanism is due to removal of mass from grain contacts (termed pressure solution or solution transfer), with a lesser component of time-dependent crack growth and healing. The magnitude of a stress-dependent concentration increase is too large to be accounted for by elastic or dislocation strain energy-induced supersaturations, favoring instead the normal stress dependence of molar Gibbs free energy associated with grain-grain interfaces.

Volcanic ash supports a diverse bacterial community in a marine mesocosm

USGS Publications Warehouse

Verena Witt,; Paul M Ayris,; Damby, David; Corrado Cimarelli,; Ulrich Kueppers,; Donald B Dingwell,; Gert Wörheide,

2017-01-01

Shallow-water coral reef ecosystems, particularly those already impaired by anthropogenic pressures, may be highly sensitive to disturbances from natural catastrophic events, such as volcanic eruptions. Explosive volcanic eruptions expel large quantities of silicate ash particles into the atmosphere, which can disperse across millions of square kilometres and deposit into coral reef ecosystems. Following heavy ash deposition, mass mortality of reef biota is expected, but little is known about the recovery of post-burial reef ecosystems. Reef regeneration depends partly upon the capacity of the ash deposit to be colonised by waterborne bacterial communities and may be influenced to an unknown extent by the physiochemical properties of the ash substrate itself. To determine the potential for volcanic ash to support pioneer bacterial colonisation, we exposed five well-characterised volcanic and coral reef substrates to a marine aquarium under low light conditions for 3 months: volcanic ash, synthetic volcanic glass, carbonate reef sand, calcite sand and quartz sand. Multivariate statistical analysis of Automated Ribosomal Intergenic Spacer Analysis (ARISA) fingerprinting data demonstrates clear segregation of volcanic substrates from the quartz and coral reef substrates over 3 months of bacterial colonisation. Overall bacterial diversity showed shared and substrate-specific bacterial communities; however, the volcanic ash substrate supported the most diverse bacterial community. These data suggest a significant influence of substrate properties (composition, granulometry and colour) on bacterial settlement. Our findings provide first insights into physicochemical controls on pioneer bacterial colonisation of volcanic ash and highlight the potential for volcanic ash deposits to support bacterial diversity in the aftermath of reef burial, on timescales that could permit cascading effects on larval settlement.

The geology of the Florida land-pebble phosphate deposits

USGS Publications Warehouse

Cathcart, J.B.; Blade, L.V.; Davidson, D.F.; Ketner, K.B.

1952-01-01

The land-pebble phosphate district is on the Gulf Coastal Plain of Florida. The phosphate deposits are in the Bone Valley formation, dated Pliocene by most writers. These strata overlie the Miocene Hawthorn formation and are overlain by consolidated sands 3 to 20 feet thick. The minable phosphate deposits, called “matrix” in the district, range from a featheredge to about 50 feet in thickness and consist of phosphatic pellets and nodules, quartz sand, and montmorillonitic clay in about equal proportions. Locally the matrix displays cross-bedding and horizontal laminations, but elsewhere it is structureless. The phosphorite particles, composed largely of carbonate-fluorapatite, range in diameter from less than 0.1 mm to about 60 cm and in P2O5 content from 30 to 36 percent. Coarse-pebble deposits, containing 30 to 34 percent P2O5 are found mainly on basement highs; and fine-pebble deposits, containing 32 to 36 percent P2O5 are, are found in basement lows. Deposits in the northern part of the field contain more phosphate particles and their P2O5 content is higher than those in the southern part. The upper part of the phosphatic strata is leached to an advanced degree and consists of quartz sand and clay-sized particules of pseudowavellite and wavellite. The leached zone ranges in thickness from a featheredge to 60 feet. The origin of the land-pebble deposits is incompletely known. Possible modes of origin are a residuum of Miocene age, or a reworked residuum of Pliocene or Quaternary age.

Sand dunes on the central Delmarva Peninsula, Maryland and Delaware

USGS Publications Warehouse

Denny, Charles Storrow; Owens, James Patrick

1979-01-01

Inconspicuous ancient sand dunes are present in parts of the central Delmarva Peninsula, Maryland and Delaware. Many dunes are roughly V-shaped, built by northwest winds, especially on the east sides of some of the large rivers. On the uplands, the form and spacing of the dunes are variable. A surficial blanket composed mainly of medium and fine-grained sand-the Parsonsburg Sand-forms both the ancient dunes and the broad plains between the dunes. The sand that forms the dunes is massive and intensely burrowed in the upper part; traces of horizontal or slightly inclined bedding appear near the base. Quartz is the dominant mineral constituent of the sand. Microline is abundant in the very fine to fine sand fraction. The heavy-mineral assemblages (high zircon, tourmaline, rutile) are more mature than in most of the possible source rocks. The most abundant minerals in the clay-sized fraction are dioctahedral vermiculite, kaolinite, illite, montmorillonite, and gibbsite. The first four minerals are common in deposits of late Wisconsin and Holocene age. The gibbsite may be detrital, coming from weathered rocks of Tertiary age. The soil profile in the dune sand is weakly to moderately developed. At or near the base of the Parsonsburg Sand are peaty beds that range in age from about 30,000 to about 13,000 radiocarbon years B.P. Microfloral assemblages in the peaty beds suggest that the dunes on the uplands formed in a spruce parkland during the late Wisconsin glacial maximum. The river dunes may also be of late Wisconsin age, but could be Holocene.

Lower Jurassic Navaho-Aztec-Equivalent Sandstones in southern Arizona and their paleogeographic significance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bilodeau, W.L.; Keith, S.B.

1986-06-01

Thick sequences of Lower Jurassic rhyolitic and andesitic volcanic rocks in several mountain ranges of southern Arizona contain interbedded quartzarenites. Locally up to 250 m thick, these sandstone lenses, composed of well-sorted and well-rounded quartz grains, commonly contain large-scale cross-stratification and are considered to be eolian sand deposits. The eolian sands were blown up against the continental side of the Early Jurassic volcanic arc that trended northwest-southeast across the southwestern margin of the North American continent and/or plate at that time. Paleocurrent data suggest southerly eolian transport of the sands from the Colorado Plateau area. Correlation of these sandstones withmore » the Lower Jurassic Navaho and Aztec Sandstones is indicated by the paleocurrent data as well as radiometric dating of the interbedded volcanics. Eolian sand transport southward across central Arizona in the Early Jurassic indicates that the Mogollon highlands either did not then exist, or were merely low, discontinuous inselbergs on a broad back-arc ramp, more appropriately called the Mogollon slope.« less

Self assembly, mobilization, and flotation of crude oil contaminated sand particles as granular shells on gas bubbles in water.

PubMed

Tansel, Berrin; Boglaienko, Daria

2017-01-01

Contaminant fate and transport studies and models include transport mechanisms for colloidal particles and dissolved ions which can be easily moved with water currents. However, mobilization of much larger contaminated granular particles (i.e., sand) in sediments have not been considered as a possible mechanism due to the relatively larger size of sand particles and their high bulk density. We conducted experiments to demonstrate that oil contaminated granular particles (which exhibit hydrophobic characteristics) can attach on gas bubbles to form granular shells and transfer from the sediment phase to the water column. The interactions and conditions necessary for the oil contaminated granular particles to self assemble as tightly packed granular shells on the gas bubbles which transfer from sediment phase to the water column were evaluated both experimentally and theoretically for South Louisiana crude oil and quartz sand particles. Analyses showed that buoyancy forces can be adequate to move the granular shell forming around the air bubbles if the bubble radius is above 0.001mm for the sand particles with 0.28mm diameter. Relatively high magnitude of the Hamaker constant for the oil film between sand and air (5.81×10 -20 J for air-oil-sand) indicates that air bubbles have high affinity to attach on the oil film that is on the sand particles in comparison to attaching to the sand particles without the oil film in water (1.60×10 -20 J for air-water-sand). The mobilization mechanism of the contaminated granular particles with gas bubbles can occur in natural environments resulting in transfer of granular particles from sediments to the water column. Copyright © 2016 Elsevier B.V. All rights reserved.

Source versus depositional controls on sandstone composition in a foreland basin: The El Imperial Formation (Mid Carboniferous-Lower Permian), San Rafael basin, western Argentina

DOE Office of Scientific and Technical Information (OSTI.GOV)

Espejo, E.S.; Lopez-Gamundi, O.R.

1994-01-01

The El Imperial Formation (mid-Carboniferous-Lower Permian) constitutes a progradational sandstone-rich succession deposited in the San Rafael foreland basin of western Argentina. Four facies associations have been identified: a basal glacial marine association, a shallow marine association, a deltaic association, and an uppermost fluvial association. Sand-prone deposits in the deltaic association, a shallow marine association, a deltaic association, and an uppermost fluvial association. Sand-prone deposits in the deltaic association are represented by prodelta and delta-front shales and subordinate fine sandstones (Facies A), deltaic platform, wave-reworked channel mouth-bar sandstones (Facies B), and fluvial-dominated distributary channel sandstones (Facies C). Analysis of framework grainsmore » of sandstone samples from Facies B and C shows two distinct mineral assemblages or petrofacies. The quartzose petrofacies is characterized by high contents of quartz and low percentages of feldspar and lithic grains. The quartzolithic petrofacies shows an increase in labile components, in particular lithic fragments, and a concomitant decrease in quartz. The quartzolithic petrofacies shows a source signature. Average detrital modes of sandstones from this petrofacies are similar to those from overlying fluvial sandstones. All wave-reworked, channel mouth-bar sandstones (Facies B) correspond compositionally to the quartzose petrofacies, whereas detrital modes from the distributary-channel sandstones (Facies C) fall into the quartzolithic petrofacies. This correspondence between depositional environment and petrofacies suggests a strong depositional influence on composition (depositional signature). Abrasion (mechanical breakdown) by wave action in shallow marine environments accounts for the quartz-rich nature and paucity of labile grains in the quartzose petrofacies.« less

The significance of stylolitization and intergranular pressure solution in the formation of pressure compartment seals in the St. Peter Sandstone, Ordovician, Michigan basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Drzewiecki, P.A.; Simo, T.; Moline, G.

1991-03-01

The Middle to Late Ordovician St. Peter Sandstone of the Michigan basin is a fine- to medium-grained quartz sandstone. Extensive stylolitization and intergranular pressure solution have been major factors in reducing the porosity of certain horizons within the St. Peter, resulting in pressure compartmentation of the reservoir. Pressure versus depth data for various Michigan basin wells indicate that the basin contains compartments that are overpressured by as much as 500 psi. Horizons bounding these compartments are often affected by intense stylolitization (or intergranular pressure solution) and quartz cementation and have been correlated with zones of low porosity and permeability ({phi}more » = 0-3%, k = <50 {mu}d). These tight zones can be correlated within single gas fields, and some may extend across the Michigan basin. The St. Peter Sandstone has been buried to depths of about 3,500 m in the central part of the basin and 1,500 m at the margins. Intensely stylolitized zones are found at all depths throughout the basin and do not appear to change in abundance or style with depths. Factors that influence the formation, morphology, and abundance of stylolites in the St. Peter include (1) clay intraclasts, (2) intergranular clay, and (3) fine-grained, feldspar-rich sand. Stylolites also occur at contacts between quartz-cemented and carbonate-cemented zones and within well-cemented sands. Intergranular pressure solution and stylolites may be responsible for the formation of a compartment seal. Understanding their genesis can allow prediction of variations in porosity in Michigan basin well cores.« less

The effect of surface characteristics on the transport of multiple Escherichia coli isolates in large scale columns of quartz sand.

PubMed

Lutterodt, G; Basnet, M; Foppen, J W A; Uhlenbrook, S

2009-02-01

Bacteria properties play an important role in the transport of bacteria in groundwater, but their role, especially for longer transport distances (>0.5 m) has not been studied. Thereto, we studied the effects of cell surface hydrophobicity, outer surface potential (OSP), cell sphericity, motility, and Ag43 protein expression on the outer cell surface for a number of E. coli strains, obtained from the environment on their transport behavior in columns of saturated quartz sand of 5 m height in two solutions: demineralized (DI) water and artificial groundwater (AGW). In DI water, sticking efficiencies ranged between 0.1 and 0.4 at the column inlet, and then decreased with transport distance to 0.02-0.2. In AGW, sticking efficiencies were on average 1log-unit higher than those in DI (water). Bacteria motility and Ag43 expression affected attachment with a (high) statistical significance. In contrast, hydrophobicity, OSP and cell sphericity did not significantly correlate with sticking efficiency. However, for transport distances more than 0.33 m, the correlation between sticking efficiency, Ag43 expression, and motility became insignificant. We concluded that Ag43 and motility played an important role in E. coli attachment to quartz grain surfaces, and that the transport distance dependent sticking efficiency reductions were caused by motility and Ag43 expression variations within a population. The implication of our findings is that less motile bacteria with little or no Ag43 expression may travel longer distances once they enter groundwater environments. In future studies, the possible effect of bacteria surface structures, like fimbriae, pili and surface proteins on bacteria attachment need to be considered more systematically in order to arrive at more meaningful inter-population comparisons of the transport behavior of E. coli strains in aquifers.

Linking Spectral Induced Polarization (SIP) and Subsurface Microbial Processes: Results from Sand Column Incubation Experiments.

PubMed

Mellage, Adrian; Smeaton, Christina M; Furman, Alex; Atekwana, Estella A; Rezanezhad, Fereidoun; Van Cappellen, Philippe

2018-02-20

Geophysical techniques, such as spectral induced polarization (SIP), offer potentially powerful approaches for in situ monitoring of subsurface biogeochemistry. The successful implementation of these techniques as monitoring tools for reactive transport phenomena, however, requires the deconvolution of multiple contributions to measured signals. Here, we present SIP spectra and complementary biogeochemical data obtained in saturated columns packed with alternating layers of ferrihydrite-coated and pure quartz sand, and inoculated with Shewanella oneidensis supplemented with lactate and nitrate. A biomass-explicit diffusion-reaction model is fitted to the experimental biogeochemical data. Overall, the results highlight that (1) the temporal response of the measured imaginary conductivity peaks parallels the microbial growth and decay dynamics in the columns, and (2) SIP is sensitive to changes in microbial abundance and cell surface charging properties, even at relatively low cell densities (<10 8 cells mL -1 ). Relaxation times (τ) derived using the Cole-Cole model vary with the dominant electron accepting process, nitrate or ferric iron reduction. The observed range of τ values, 0.012-0.107 s, yields effective polarization diameters in the range 1-3 μm, that is, 2 orders of magnitude smaller than the smallest quartz grains in the columns, suggesting that polarization of the bacterial cells controls the observed chargeability and relaxation dynamics in the experiments.

Umbrisols at Lower Altitudes, Case Study from Borská lowland (Slovakia)

NASA Astrophysics Data System (ADS)

Jenčo, Marián; Matečný, Igor; Putiška, René; Burian, Libor; Tančárová, Kristína; Kušnirák, Dávid

2018-05-01

Umbrisols generally develop in a cool and humid climate. Therefore, occurrence of these soils in the Borská lowland of southwestern Slovakia is very uncommon, and this inspired the aim of this paper: Analysis of the natural conditions suitable for Umbrisol development. Umbrisols in the Borská lowland developed from aeolian quartz sands accumulated on Neogenne marine clay sediments. Their occurrence is connected with the groundwater table relatively close to the ground surface and this particularly determines Umbrisol genesis in this area. Sufficient input via organic matter is an important factor for formation of the umbric horizon, and only the rich herbaceous undergrowth of the prevailing planted pine and mixed pine-oak forests is capable of providing it. A growth of diep-rooted grass is closely connected with higher soil moisture content, and quite moist areas occur in the deeper inter-dunes depressions. Constant soil moisture in these sites is facilitated by water capillary elevation. While Umbrisols are transformed to Arenosols at increased altitude, they can be transformed to Gleysols in deep depressions. Herein, induced polarization provided suitable geophysical method for detection of arenic Umbrisol inclusions. Sharp transformation of the humus layer to dry non-polarized aeolian quartz sands enabled the surface horizon to be distinguished by induced polarization

Dynamic and impact contact mechanics of geologic materials: Grain-scale experiments and modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cole, David M.; Hopkins, Mark A.; Ketcham, Stephen A.

2013-06-18

High fidelity treatments of the generation and propagation of seismic waves in naturally occurring granular materials is becoming more practical given recent advancements in our ability to model complex particle shapes and their mechanical interaction. Of particular interest are the grain-scale processes that are activated by impact events and the characteristics of force transmission through grain contacts. To address this issue, we have developed a physics based approach that involves laboratory experiments to quantify the dynamic contact and impact behavior of granular materials and incorporation of the observed behavior indiscrete element models. The dynamic experiments do not involve particle damagemore » and emphasis is placed on measured values of contact stiffness and frictional loss. The normal stiffness observed in dynamic contact experiments at low frequencies (e.g., 10 Hz) are shown to be in good agreement with quasistatic experiments on quartz sand. The results of impact experiments - which involve moderate to extensive levels of particle damage - are presented for several types of naturally occurring granular materials (several quartz sands, magnesite and calcium carbonate ooids). Implementation of the experimental findings in discrete element models is discussed and the results of impact simulations involving up to 5 Multiplication-Sign 105 grains are presented.« less

Removal of ammonium and heavy metals by cost-effective zeolite synthesized from waste quartz sand and calcium fluoride sludge.

PubMed

Zhang, Qian; Lin, Bing; Hong, Junming; Chang, Chang-Tang

2017-02-01

This study focuses on the effectiveness of zeolite (10% CF-Z [0.5]) hydrothermally synthesized from waste quartz sand and calcium fluoride (CF) for ammonium ion and heavy metal removal. Zeolite was characterized through powder X-ray diffraction, Fourier-transform infrared spectroscopy, micromeritics N 2 adsorption/desorption analysis, and field emission scanning electron microscopy. The effects of CF addition, Si/Al ratio, initial ammonium concentration, solution pH, and temperature on the adsorption of ammonium on 10% CF-Z (0.5) were further examined. Results showed that 10% CF-Z (0.5) was a single-phase zeolite A with cubic-shaped crystals and 10% CF-Z (0.5) efficiently adsorbs ammonium and heavy metals. For instance, 91% ammonium (10 mg L -1 ) and 93% lead (10 mg L -1 ) are removed. The adsorption isotherm, kinetics, and thermodynamics of ammonium adsorption on 10% CF-Z (0.5) were also theoretically analyzed. The adsorption isotherm of ammonium and lead on 10% CF-Z (0.5) in single systems indicated that Freundlich model provides the best fit for the equilibrium data, whereas pseudo-second-order model best describes the adsorption kinetics. The adsorption degree of ions on 10% CF-Z (0.5) in mixed systems exhibits the following pattern: lead > ammonium > cadmium > chromium.

Valorisation of different types of boron-containing wastes for the production of lightweight aggregates.

PubMed

Kavas, T; Christogerou, A; Pontikes, Y; Angelopoulos, G N

2011-01-30

Four boron-containing wastes (BW), named as Sieve (SBW), Dewatering (DBW), Thickener (TBW) and Mixture (MBW) waste, from Kirka Boron plant in west Turkey were investigated for the formation of artificial lightweight aggregates (LWA). The characterisation involved chemical, mineralogical and thermal analyses as well as testing of their bloating behaviour by means of heating microscopy. It was found that SBW and DBW present bloating behaviour whereas TBW and MBW do not. Following the above results two mixtures M1 and M2 were prepared with (in wt.%): 20 clay mixture, 40 SBW, 40 DBW and 20 clay mixture, 35 SBW, 35 DBW, 10 quartz sand, respectively. Two different firing modes were applied: (a) from room temperature till 760 °C and (b) abrupt heating at 760 °C. The obtained bulk density for M1 and M2 pellets is 1.2g/cm(3) and 0.9 g/cm(3), respectively. The analysis of microstructure with electron microscopy revealed a glassy phase matrix and an extended formation of both interconnected and isolated, closed pores. The results indicate that SBW and DBW boron-containing wastes combined with a clay mixture and quartz sand can be valorised for the manufacturing of lightweight aggregates. Copyright © 2010 Elsevier B.V. All rights reserved.

Dependence the Integrated Energy of the Electromagnetic Response from Excitation Pulse Duration for Epoxy Samples With Sand Filler

NASA Astrophysics Data System (ADS)

Surzhikov, V. P.; Demikhova, A. A.

2017-01-01

Results of research of influence of the excitation pulse duration on the parameters of the electromagnetic response of epoxy samples with filler the quartz sand presented in the paper. The electric component of a response was registered by the capacitive sensors using a differential amplifier. Measurements were carried out at two frequencies of the master generator of 65 kHz and 74 kHz. The pulse duration was changing from 10 to 100 microseconds. The stepped sort of dependence of the integrated oscillations energy in the response from duration of the excitation pulse was discovered. The conclusion was made about the determining role of the normal oscillations in formation of such dependence.

Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

NASA Astrophysics Data System (ADS)

Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

2017-04-01

Sandstones represent a traditional natural stones which are widely used in Czech architecture and sculpture over a long time. Thanks to their relatively easy workability, sandstones provide a wide range of stone products and also represent a popular material for architectural and sculptural purposes. In the field of restoration of artworks, they are therefore often used for manufacturing stone statue copies originally made from the same or similar type of stone. Despite a relatively common and varied occurrence of natural sandstones, the method of the artificial stone facsimiles creation in the form of various cast elements is also often applied in restoration practice. The history of application of artificial stones in civil engineering and architecture goes back to the ancient times, i.e. to Roman antiquity and possibly up to the time of ancient Egypt. The lack of appropriate natural rock, suitable in the view of colour, grain size or texture is the main reason of manufacturing copies based on synthetic mixtures. The other reason is high financial costs to create a sculpture copy from natural materials. Mixtures made from white and/or grey cements, sands, carefully selected crushed stone or well graded natural gravels, and mineral coloring pigments or mixtures with acrylate, polyester, and epoxy resins binder are the most frequently used artificial materials for cast stone manufacturing. This paper aims to bring information about composition and properties of artificial sandstones made from alkali-activated binder mixtures based on metakaolin and granulated blast furnace slag. The filler of this artificial stone is represented by fine-grained sand generated during kaolin wet processing. Used sand is mainly formed by quartz, feldspars, micas (muscovite > biotite), residual kaolin, and to a lesser extent also by Fe oxyhydroxides ("limonite"), titanium dioxide mineral (probably anatase), and carbonate mineral unidentified in detail. Annual Czech production of this sand from kaolin-washing process is of several hundred thousand tonnes and it thus represent so far a relatively rarely used natural building material which is currently usually deposited in worked-out areas of kaolin quarries. One of the main reasons of very difficult usability of this sands in building material industry is their behavior when exposed to the weather. In only a very short time of exposure in outdoor condition they may change in colour from greyish white to yellow-brown or golden yellow. This colour change is accompanied by significant decrease of pH values of sand leachate up to pH ranging between 3.5 and 5.5, in extreme cases even up to 2.0. Despite these extreme chemical properties of sands under study, the artificial sandstone, very similar in the physical and mechanical properties to natural ones, was successfully prepared in the laboratory. Due to the mineralogical composition of applied sands (i.e. the presence not only of quartz, but also of feldspar and muscovite), the artificial sandstone is characterized by relatively true natural appearance.

Quartz grains reveal sedimentary palaeoenvironment and past storm events: A case study from eastern Baltic

NASA Astrophysics Data System (ADS)

Kalińska-Nartiša, Edyta; Stivrins, Normunds; Grudzinska, Ieva

2018-01-01

Sediment record collected from the coastal lake serves as a powerful tool for reconstructing changes in palaeoenvironment and understanding the potential signals of past storminess. In this study, we use several proxies from sediment of the Holocene Thermal Maximum at coastal Lake Lilaste, Latvia. We focus on surface texture of quartz grains from the mineral inorganic fraction as indicators of depositional environments. We then use this as a proxy for potential storm transport and combine with information on granulometry, diatom stratigraphy and chronology to answer the question whether flux of quartz grains in the lake originated from the sea or from the land. Analyses in a binocular and scanning electron microscope reveal that most of the investigated quartz grains originate from dwelling in the seawater and wave action in the nearshore zone. Grains representing very energetic subaqueous environment similar to storm events are also present. Terrestrial record is of minor significance and visible through occurrence of aeolian quartz grains. During drier and colder conditions, an influx of sand with aeolian imprint was delivered to the lake between 8500 and 7800 cal yr BP. Marine and terrestrial conditions alternated between 7800 and 6000 cal yr BP. Storm-induced grains were likely deposited three times: at 7300 cal yr BP, 6600-6400 cal yr BP, and 6200-6000 cal yr BP. Overall stable marine environmental conditions prevailed between 6000 and 4000 cal yr BP except of the last portion of terrestrial-induced sediment at 4100 cal yr BP.

Experimental study on the ejecta-velocity distributions caused by low-velocity impacts on quartz sand

NASA Astrophysics Data System (ADS)

Tsujido, S.; Arakawa, M.; Suzuki, A. I.; Yasui, M.

2014-07-01

Introduction: Regolith formation on asteroids is caused by successive impacts of small bodies. The ejecta velocity distribution during the crater formation process is one of the most important physical properties related to the surface-evolution process, and the distribution is also necessary to reconstruct the planetary-accretion process among planetesimals. The surface of small bodies, such as asteroids and planetesimals in the solar system, could have varying porosity, strength, and density, and the impact velocity could vary across a wide range from a few tens of m/s to several km/s. Therefore, it is necessary to conduct impact experiments by changing the physical properties of the target and the projectile in a wide velocity range in order to constrain the crater-formation process applicable to the small bodies in the solar system. Housen and Holsapple (2011) compiled the data of ejecta velocity distribution with various impact velocities, porosities, grain sizes, grain shapes, and strengths of the targets, and they improved their ejecta scaling law. But the ejecta velocity data is not enough for varying projectile densities and for impact velocities less than 1 km/s. In this study, to investigate the projectile density dependence of the ejecta velocity distribution at a low velocity region, we conducted impact experiments with projectile densities from 1.1 to 11.3 g/cm^3. Then, we try to determine the effect of projectile density on the ejecta velocity distribution by means of the observation of each individual ejecta grain. Experimental methods: We made impact cratering experiments by using a vertical-type one-stage light-gas gun (V-LGG) set at Kobe University. Targets were quartz sand (irregular shape) and glass beads (spherical shape) with the grain size of 500 μ m (porosity 44.7 %). The target container with the size of 30 cm was set in a large vacuum chamber with air pressure less than 10^3 Pa. The projectile materials that we used were lead, copper, iron, titanium, zirconia, alumina, glass, and nylon (11.3-1.1 g/cm^3). The projectile shape was spherical with a diameter 2a = 3 mm. The projectile was launched at the impact velocity, V_i, from 24 to 217 m/s. We made impact experiments using 8 types of projectiles and observed each ejecta grain by using a high-speed digital video camera taken at 2000-10000 FPS. Then, we measured the ejection velocity and ejection angle of each grain varying with the initial position. We successfully obtained the relationship between the initial position and the initial ejection velocity for the quartz sand grains and the glass beads. Results: From the high-speed camera observation, we found that, for higher projectile density, the angle of ejecta curtain from the horizontal plane increases from 50° for nylon to 58° for zirconia. The ejection angle of each grain was observed to change with the initial position, x, from 50° near the impact point to 40° near the crater rim, and this relationship does not depend on the projectile density. Thus, the ejection angle of each grain cannot explain the change in the angle of ejecta curtain for each projectile. When the ejecta velocity distribution, V_e, is written in the form of V_e/V_i=c(x/a)^{-b}, c is seen to somewhat change in each projectile. Meanwhile, b depends on the projectile density, and it was revealed that, for increasing projectile densities, b decreases from 0.43 of nylon to 0.68 of zirconia. It is assumed that b depending on the projectile density could cause the difference of ejecta curtain formed by each projectile. When comparing the results of Housen and Holsapple (2011), who made experiments for a quartz sand target at high speeds of 1000-1900 m/s, with the results of this study for quartz sand or 500 μ m glass beads target at low velocities of 24-217 m/s, the two sets of results were found to be consistent, even though our velocity range was an order of magnitude smaller than their velocity range. In addition, when the velocity distributions are written in the form V_i/√{gR}=k(x/R)^{-b}, where R is a crater radius, g is the gravitational acceleration of planet, k is obtained to be approximately a constant of 0.78±0.17, irrespective of projectile density. Our results in low-velocity experiments for 500 μ m glass beads target are also roughly consistent with the results for the quartz sand target. In other words, we found that the shape of the target grain does not affect the velocity distribution so much, and the current scaling law can explain the effect of the impact velocity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doebrich, J.L.; Murchey, B.L.; Theodore, T.G.

Recently completed 1:24,000-scale geologic mapping and biostratigraphic studies of the Mississippian, Pennsylvanian, and Permian Havallah sequence in the Valmy, North Peak, and Antler Peak quadrangles of the Battle Mountain area have documented a significant amount of imbricate thrusting in the Golconda allochthon (GA) and defined depositional environments that existed in the Havallah basin. Furthermore, the Willow Creek thrust (WCT) is identified as a major N-striking W-dipping structure, fairly continuous through the quadrangles, that tectonically subdivides the allochthon into two lithotectonic units. Pennsylvanian and Permian slope deposits comprise lithotectonic unit 1 (LT1), the footwall of the WCT. LT1 consists of amore » coarsening upward sequence of sponge-spicule chert and argillite, and cherty shale, which are tectonically cut out near Trenton Canyon such that the WCT becomes the sole of the GA. Mississippian basin deposits and Pennsylvanian and Permian turbidites comprise lithotectonic unit 2 (LT2), the hanging wall of the WCT. LT2 consists of a coarsening and shallowing upward sequence of Mississippian radiolarian chert and shale, overlain by Pennsylvanian and Permian calcareous siltstone and sandstone, pebble conglomerate, and pebbly to micritic limestone. Oncolitic coatings on fossil fragments in some calcareous sands high in the stacking pattern suggest environments as shallow as 20 m. Most modes of quartz- and calcite-framework dominant sands plot in quartzose recycled orogen fields; however, compositional facies with abundant chert fragments are rare in contrast with quartz-chert petrofacies sands reported for the GA in the Mount Tobin area. Extrabasinal carbonate grains at framework sites may have been derived from elevated fault blocks or platforms west of the Antler highlands. These studies confirm that turbiditic rocks in the GA show ample evidence in their provenance for having attachments to a nearby continental margin.« less

Volcanic ash supports a diverse bacterial community in a marine mesocosm.

PubMed

Witt, V; Ayris, P M; Damby, D E; Cimarelli, C; Kueppers, U; Dingwell, D B; Wörheide, G

2017-05-01

Shallow-water coral reef ecosystems, particularly those already impaired by anthropogenic pressures, may be highly sensitive to disturbances from natural catastrophic events, such as volcanic eruptions. Explosive volcanic eruptions expel large quantities of silicate ash particles into the atmosphere, which can disperse across millions of square kilometres and deposit into coral reef ecosystems. Following heavy ash deposition, mass mortality of reef biota is expected, but little is known about the recovery of post-burial reef ecosystems. Reef regeneration depends partly upon the capacity of the ash deposit to be colonised by waterborne bacterial communities and may be influenced to an unknown extent by the physiochemical properties of the ash substrate itself. To determine the potential for volcanic ash to support pioneer bacterial colonisation, we exposed five well-characterised volcanic and coral reef substrates to a marine aquarium under low light conditions for 3 months: volcanic ash, synthetic volcanic glass, carbonate reef sand, calcite sand and quartz sand. Multivariate statistical analysis of Automated Ribosomal Intergenic Spacer Analysis (ARISA) fingerprinting data demonstrates clear segregation of volcanic substrates from the quartz and coral reef substrates over 3 months of bacterial colonisation. Overall bacterial diversity showed shared and substrate-specific bacterial communities; however, the volcanic ash substrate supported the most diverse bacterial community. These data suggest a significant influence of substrate properties (composition, granulometry and colour) on bacterial settlement. Our findings provide first insights into physicochemical controls on pioneer bacterial colonisation of volcanic ash and highlight the potential for volcanic ash deposits to support bacterial diversity in the aftermath of reef burial, on timescales that could permit cascading effects on larval settlement. © 2017 The Authors. Geobiology Published by John Wiley & Sons Ltd.

The Dependence of Water Permeability in Quartz Sand on Gas Hydrate Saturation in the Pore Space

NASA Astrophysics Data System (ADS)

Kossel, E.; Deusner, C.; Bigalke, N.; Haeckel, M.

2018-02-01

Transport of fluids in gas hydrate bearing sediments is largely defined by the reduction of the permeability due to gas hydrate crystals in the pore space. Although the exact knowledge of the permeability behavior as a function of gas hydrate saturation is of crucial importance, state-of-the-art simulation codes for gas production scenarios use theoretically derived permeability equations that are hardly backed by experimental data. The reason for the insufficient validation of the model equations is the difficulty to create gas hydrate bearing sediments that have undergone formation mechanisms equivalent to the natural process and that have well-defined gas hydrate saturations. We formed methane hydrates in quartz sand from a methane-saturated aqueous solution and used magnetic resonance imaging to obtain time-resolved, three-dimensional maps of the gas hydrate saturation distribution. These maps were fed into 3-D finite element method simulations of the water flow. In our simulations, we tested the five most well-known permeability equations. All of the suitable permeability equations include the term (1-SH)n, where SH is the gas hydrate saturation and n is a parameter that needs to be constrained. The most basic equation describing the permeability behavior of water flow through gas hydrate bearing sand is k = k0 (1-SH)n. In our experiments, n was determined to be 11.4 (±0.3). Results from this study can be directly applied to bulk flow analysis under the assumption of homogeneous gas hydrate saturation and can be further used to derive effective permeability models for heterogeneous gas hydrate distributions at different scales.

Mineralogy, morphology, and textural relationships in coatings on quartz grains in sediments in a quartz-sand aquifer

USGS Publications Warehouse

Zhang, Shouliang; Kent, Douglas B.; Elbert, David C.; Shi, Zhi; Davis, James A.; Veblen, David R.

2011-01-01

Mineralogical studies of coatings on quartz grains and bulk sediments from an aquifer on Western Cape Cod, Massachusetts, USA were carried out using a variety of transmission electron microscopy (TEM) techniques. Previous studies demonstrated that coatings on quartz grains control the adsorption properties of these sediments. Samples for TEM characterization were made by a gentle mechanical grinding method and focused ion beam (FIB) milling. The former method can make abundant electron-transparent coating assemblages for comprehensive and quantitative X-ray analysis and the latter technique protects the coating texture from being destroyed. Characterization of the samples from both a pristine area and an area heavily impacted by wastewater discharge shows similar coating textures and chemical compositions. Major constituents of the coating include Al-substituted goethite and illite/chlorite clays. Goethite is aggregated into well-crystallized domains through oriented attachment resulting in increased porosity. Illite/chlorite clays with various chemical compositions were observed to be mixed with goethite aggregates and aligned sub-parallel to the associated quartz surface. The uniform spatial distribution of wastewater-derived phosphorus throughout the coating from the wastewater-contaminated site suggests that all of the coating constituents, including those adjacent to the quartz surface, are accessible to groundwater solutes. Both TEM characterization and chemical extraction results indicate there is a significantly greater amount of amorphous iron oxide in samples from wastewater discharge area compared to those from the pristine region, which might reflect the impact of redox cycling of iron under the wastewater-discharge area. Coating compositions are consistent with the moderate metal and oxy-metalloid adsorption capacities, low but significant cation exchange capacities, and control of iron(III) solubility by goethite observed in reactive transport experimental and modeling studies conducted at the site.

Time/Frequency Relationships for an FFT-Based Acoustic Modem

DTIC Science & Technology

2010-09-01

Jenkins II 5. FUNDING NUMBERS 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Naval Postgraduate School Monterey, CA 93943-5000 8. PERFORMING... seawater , and a fluid- like bottom composed of quartz sand. From [11] ............................................18  Table 3.  Transmission loss at the...in St. Andrew’s Bay, Florida [4]. The goal of this sea testing was to observe the effects of natural and man-made noise on network performance in a

The influence of groundwater chemistry on arsenic concentrations and speciation in a quartz sand and gravel aquifer

USGS Publications Warehouse

Kent, D.B.; Fox, P.M.

2004-01-01

We examined the chemical reactions influencing dissolved concentrations, speciation, and transport of naturally occurring arsenic (As) in a shallow, sand and gravel aquifer with distinct geochemical zones resulting from land disposal of dilute sewage effluent. The principal geochemical zones were: (1) the uncontaminated zone above the sewage plume [350 ??M dissolved oxygen (DO), pH 5.9]; (2) the suboxic zone (5 ??M DO, pH 6.2, elevated concentrations of sewage-derived phosphate and nitrate); and (3) the anoxic zone [dissolved iron(II) 100-300 ??M, pH 6.5-6.9, elevated concentrations of sewage-derived phosphate]. Sediments are comprised of greater than 90% quartz but the surfaces of quartz and other mineral grains are coated with nanometer-size iron (Fe) and aluminum (Al) oxides and/or silicates, which control the adsorption properties of the sediments. Uncontaminated groundwater with added phosphate (620 ??M) was pumped into the uncontaminated zone while samples were collected 0.3 m above the injection point. Concentrations of As(V) increased from below detection (0.005 ??M) to a maximum of 0.07 ??M during breakthrough of phosphate at the sampling port; As(III) concentrations remained below detection. These results are consistent with the hypothesis that naturally occurring As(V) adsorbed to constituents of the coatings on grain surfaces was desorbed by phosphate in the injected groundwater. Also consistent with this hypothesis, vertical profiles of groundwater chemistry measured prior to the tracer test showed that dissolved As(V) concentrations increased along with dissolved phosphate from below detection in the uncontaminated zone to approximately 0.07 and 70 ??M, respectively, in the suboxic zone. Concentrations of As(III) were below detection in both zones. The anoxic zone had approximately 0.07 ??M As(V) but also had As(III) concentrations of 0.07-0.14 ??M, suggesting that release of As bound to sediment grains occurred by desorption by phosphate, reductive dissolution of Fe oxides, and reduction of As(V) to As(III), which adsorbs only weakly to the Fe-oxide-depleted material in the coatings. Results of reductive extractions of the sediments suggest that As associated with the coatings was relatively uniformly distributed at approximately 1 nmol/g of sediment (equivalent to 0.075 ppm As) and comprised 20%-50% of the total As in the sediments, determined from oxidative extractions. Quartz sand aquifers provide high-quality drinking water but can become contaminated when naturally occurring arsenic bound to Fe and Al oxides or silicates on sediment surfaces is released by desorption and dissolution of Fe oxides in response to changing chemical conditions. ?? 2004 American Institute of Physics.

Glass Microbeads in Analog Models of Thrust Wedges.

PubMed

D'Angelo, Taynara; Gomes, Caroline J S

2017-01-01

Glass microbeads are frequently used in analog physical modeling to simulate weak detachment zones but have been neglected in models of thrust wedges. Microbeads differ from quartz sand in grain shape and in low angle of internal friction. In this study, we compared the structural characteristics of microbeads and sand wedges. To obtain a better picture of their mechanical behavior, we determined the physical and frictional properties of microbeads using polarizing and scanning electron microscopy and ring-shear tests, respectively. We built shortening experiments with different basal frictions and measured the thickness, slope and length of the wedges and also the fault spacings. All the microbeads experiments revealed wedge geometries that were consistent with previous studies that have been performed with sand. However, the deformation features in the microbeads shortened over low to intermediate basal frictions were slightly different. Microbeads produced different fault geometries than sand as well as a different grain flow. In addition, they produced slip on minor faults, which was associated with distributed deformation and gave the microbeads wedges the appearance of disharmonic folds. We concluded that the glass microbeads may be used to simulate relatively competent rocks, like carbonates, which may be characterized by small-scale deformation features.

Mineral resources and land use in Stanislaus County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higgins, C.T.; Dupras, D.L.; Chapman, R.H.

1993-04-01

Stanislaus County covers portions of 3 geologic provinces: Coast Ranges, Great Valley, and Sierra Nevada. Each has been exploited for a distinct set of mineral resources, which include sand and gravel, ball and fire clay, placer gold, manganese, chromite, magnesite, mercury, diatomite, building stone, and mineral pigment. Of these, sand and gravel, clay, and diatomite have been the most important commodities produced recently. Sand and gravel, particularly that along the Tuolumne River, is and will continue to be the county's main mineral product; other potentially important areas include alluvial fans along the west side of the Great Valley. Clay andmore » diatomite could resume importance in the future. There is also potential for quartz-rich specialty sands. Although the county is largely rural, it is undergoing one of the highest growth rates in California. Several new residential communities are being proposed in the county, which would have two major effects on mineral resources: (1) large sources of aggregate will be required for construction, and (2) development of residential areas may preclude mining of resources in those areas. Maps of mineral resources produced by this study, will assist decisions on such potential conflicts in land use.« less

Low temperature processing of ultra-pure cellulose fibers into nylon 6 and other thermoplastics

Treesearch

Rod Jacobson; Dan Caulfield; Karl Sears; John Underwood

2002-01-01

The objective of this research was to develop a stable process for compound ultra-pure cellulose fibers into polyamides. This has been a difficult procedure and has taken years of trial and error to understand the viscosity shear heating effects associated with compounding cellulose into high-melting point engineering thermoplastics. The evolution of the low...

Origin and prospectivity of heavy mineral enriched sand deposits along the Somaliland coastal areas

NASA Astrophysics Data System (ADS)

Ali, M. Y.; Hibberd, P.; Stoikovich, B.

2018-04-01

Sixty-one heavy mineral enriched samples along the Somaliland coast from Eil Sheikh to Ras Khatib, a distance of about 130 km, were analyzed using X-ray Fluorescence, X-ray Diffraction and SEM-EDS techniques. This study reveals that a considerable amount of heavy minerals is present along the Somaliland coast and confirms the presence of high concentration titanium and iron bearing minerals. However, the backshore deposits in the mouths of Waaheen and Biyo Gure ephemeral rivers as well as raised paleo-beaches in the east of port city of Berbera demonstrate the highest level of titaniferous heavy minerals with most samples showing concentration greater than 50 wt %. The titanium detected in geochemical analysis occurs in the form of ilmenite, rutile, titanite and titaniferous magnetite. Also, present in minor or trace amounts, are garnet, zircon and monazite. Heavy mineral accumulations in the east and west of Berbera have different mineralogical assemblages. The east of Berbera is dominated by quartz with moderate concentration of plagioclase, K-feldspar, magnetite, hematite and titanium bearing minerals, whereas in the west of Berbera, the dominant minerals are quartz, K-feldspar and plagioclase with variable proportions of ilmenite, rutile, mica, amphibole and pyroxene. These variations in mineral assemblages suggest different composition of the catchment areas that supply sediment to these deposits. The catchment area in the east of Berbera consists mainly of Proterozoic crystalline basement of the Qabri Bahar complex, Gabbro-Synenite belt and granitic intrusions that outcrop in Hudiso, Tulo Dibijo and surrounding areas. The primary sources of heavy minerals in the west of Berbera comprise of high-grade metamorphic rocks of the Mora and Qabri Bahar complexes as well as the Miocene volcanics that outcrop in Laferug and Hagabo areas. The heavy mineral sand deposits observed along the Somaliland coast have the potential to provide commercially important heavy minerals, in particular ilmenite. It appears that prospects for development of the heavy mineral sands in the east of Berbera are better than those to the west of Berbera. In general, east of Berbera has wider beaches, better heavy mineral sands in the upper horizons and dune areas with heavier mineral sands. Furthermore, a series of raised paleo-beaches with high concentrations of heavy mineral sands are observed 1-2 km behind the shoreline. However, further investigation, including drilling and laboratory analyses, still needs to be carried out, particularly close to the entrance of Waaheen and Biyo Gure ephemeral rivers to evaluate the potential quality and scale of the deposits.

Method of purifying metallurgical grade silicon employing reduced pressure atmospheric control

NASA Technical Reports Server (NTRS)

Ingle, W. M.; Thompson, S. W.; Chaney, R. E. (Inventor)

1979-01-01

A method in which a quartz tube is charged with chunks of metallurgical grade silicon and/or a mixture of such chunks and high purity quartz sand, and impurities from a class including aluminum, boron, as well as certain transition metals including nickel, iron, and manganese is described. The tube is then evacuated and heated to a temperature within a range of 800 C to 1400 C. A stream of gas comprising a reactant, such as silicon tetrafluoride, is continuously delivered at low pressures through the charge for causing a metathetical reaction of impurities of the silicon and the reactant to occur for forming a volatile halide and leaving a residue of silicon of an improved purity. The reactant which included carbon monoxide gas and impurities such as iron and nickel react to form volatile carbonyls.

The chronology of Late Pleistocene thermal contraction cracking derived from sand wedge OSL dating in central and southern France

NASA Astrophysics Data System (ADS)

Andrieux, Eric; Bateman, Mark D.; Bertran, Pascal

2018-03-01

Much of France remained unglaciated during the Late Quaternary and was subjected to repeated phases of periglacial activity. Numerous periglacial features have been reported but disentangling the environmental and climatic conditions they formed under, the timing and extent of permafrost and the role of seasonal frost has remained elusive. The primary sandy infillings of relict sand-wedges and composite-wedge pseudomorphs record periglacial activity. As they contain well-bleached quartz-rich aeolian material they are suitable for optically stimulated luminescence dating (OSL). This study aims to reconstruct when wedge activity took place in two regions of France; Northern Aquitaine and in the Loire valley. Results from single-grain OSL measurements identify multiple phases of activity within sand wedges which suggest that wedge activity in France occurred at least 11 times over the last 100 ka. The most widespread events of thermal contraction cracking occurred between ca. 30 and 24 ka (Last Permafrost Maximum) which are concomitant with periods of high sand availability (MIS 2). Although most phases of sand-wedge growth correlate well with known Pleistocene cold periods, the identification of wedge activity during late MIS 5 and the Younger Dryas strongly suggests that these features do not only indicate permafrost but also deep seasonal ground freezing in the context of low winter insolation. These data also suggest that the overall young ages yielded by North-European sand-wedges likely result from poor record of periglacial periods concomitant with low sand availability and/or age averaging inherent with standard luminescence methods.

Quantitative structure property relationships for the adsorption of pharmaceuticals onto activated carbon.

PubMed

Dickenson, E R V; Drewes, J E

2010-01-01

Isotherms were determined for the adsorption of five pharmaceutical residues, primidone, carbamazepine, ibuprofen, naproxen and diclofenac, to Calgon Filtrasorb 300 powdered activated carbon (PAC). The sorption behavior was examined in ultra-pure and wastewater effluent organic matter (EfOM) matrices, where more sorption was observed in the ultra-pure water for PAC doses greater than 10 mg/L suggesting the presence of EfOM hinders the sorption of the pharmaceuticals to the PAC. Adsorption behaviors were described by the Freundlich isotherm model. Quantitative structure property relationships (QSPRs) in the form of polyparameter linear solvation energy relationships were developed for simulating the Freundlich adsorption capacity in both ultra-pure and EfOM matrices. The significant 3D-based descriptors for the QSPRs were the molar volume, polarizability and hydrogen-bond donor parameters.

Laboratory studies of dune sand for the use of construction industry in Sri Lanka

NASA Astrophysics Data System (ADS)

de Silva Jayawardena, Upali; Wijesuriya, Roshan; Abayaweera, Gayan; Viduranga, Tharaka

2015-04-01

With the increase of the annual sand demand for the construction industry the excessive excavation of river sand is becoming a serious environmental problem in Sri Lanka. Therefore, it is necessary to explore the possibility for an alternative to stop or at least to minimize river sand mining activities. Dune sand is one of the available alternative materials to be considered instead of river sand in the country. Large quantities of sand dunes occur mainly along the NW and SE coastal belt which belong to very low rainfall Dry Zone coasts. The height of dune deposits, vary from 1m to about 30 meters above sea level. The objective of this paper is to indicate some studies and facts on the dune sand deposits of Sri Lanka. Laboratory studies were carried out for visual observations and physical properties at the initial stage and then a number of tests were carried out according to ASTM standards to obtain the compressive strength of concrete cylinders and mortar cubes mixing dune sand and river sand in different percentages keeping a constant water cement ratio. Next the water cement ratio was changed for constant dune sand and river sand proportion. Microscopic analysis shows that the dune sand consist of 95 % of quartz and 5 % of garnet, feldspar, illmenite and other heavy minerals with clay, fine dust, fine shell fragments and organic matters. Grains are sub-rounded to angular and tabular shapes. The grain sizes vary from fine to medium size of sand with silt. The degree of sorting and particle size observed with dune sands are more suited with the requirement of fine aggregates in the construction industry. The test result indicates that dune sand could be effectively used in construction work without sieving and it is ideal for wall plastering due to its'-uniformity. It could also be effectively used in concrete and in mortars mixing with river sand. The best mixing ratio is 75% dune sand and 25% river sand as the fine aggregate of concrete. For mortar the mixing percentage is 50%. The best water cement ratio for mix proportion is 0.45. It was observed that the available amount of dune sand can be extracted to meet the demand for sand in construction industry. However, the extraction of dune sand from the areas close to the sea will cause several social, environmental and legal problems. Therefore sand mining from dunes must be commenced after making a detailed Environmental Impact Assessment.

Directional optical transmission through a sand layer: a preliminary laboratory experiment

NASA Astrophysics Data System (ADS)

Tian, Jia; Philpot, William D.

2017-10-01

Given the importance of penetration of light in the soil for seed germination, soil warming, and the photolytic degradation of pesticides, directional transmission of thin sand samples are studied in this paper under both dry and saturated conditions. The detector views upward through a glass-bottom sample holder, filled to 3 or 4 mm with a coarse, translucent, quartz sand sample. Transmission through the samples was measured as the illumination zenith angle moved from 0 to 70° in 5° intervals. In the most cases, transmission decreased monotonically, but slowly with increasing illumination angle at all wavelengths. A peak in transmission only appeared at 0° illumination for the low bulk density, dry sample at 3 mm depth. The 0° peak disappeared when the sample was wetted, when the bulk density increased, or when the depth of the sample increased, which indicates that the radiation transmitting through a sand layer can be diffused thoroughly with a millimeters-thin sand layer. For the saturated samples, water influences light transmission in contrasting ways in shorter and longer wavelength. Transmission increased in the VNIR when saturated relative to dry, while transmission decreased sharply after 1300 nm, with spectral absorption features characteristic of water absorption. In VNIR region, water absorption is low and the low relative index of refraction enhanced transmission through sand sample. In contrast, water absorption became dominant at longer wavelengths region leading to the strongly reduced transmission.

The effect of adsorbed liquid and material density on saltation threshold: Insight from laboratory and wind tunnel experiments

NASA Astrophysics Data System (ADS)

Yu, Xinting; Hörst, Sarah M.; He, Chao; Bridges, Nathan T.; Burr, Devon M.; Sebree, Joshua A.; Smith, James K.

2017-11-01

Saltation threshold, the minimum wind speed for sediment transport, is a fundamental parameter in aeolian processes. Measuring this threshold using boundary layer wind tunnels, in which particles are mobilized by flowing air, for a subset of different planetary conditions can inform our understanding of physical processes of sediment transport. The presence of liquid, such as water on Earth or methane on Titan, may affect the threshold values to a great extent. Sediment density is also crucial for determining threshold values. Here we provide quantitative data on density and water content of common wind tunnel materials (including chromite, basalt, quartz sand, beach sand, glass beads, gas chromatograph packing materials, walnut shells, iced tea powder, activated charcoal, instant coffee, and glass bubbles) that have been used to study conditions on Earth, Titan, Mars, and Venus. The measured density values for low density materials are higher compared to literature values (e.g., ∼30% for walnut shells), whereas for the high density materials, there is no such discrepancy. We also find that low density materials have much higher water content and longer atmospheric equilibration timescales compared to high density sediments. We used thermogravimetric analysis (TGA) to quantify surface and internal water and found that over 80% of the total water content is surface water for low density materials. In the Titan Wind Tunnel (TWT), where Reynolds number conditions similar to those on Titan can be achieved, we performed threshold experiments with the standard walnut shells (125-150 μm, 7.2% water by mass) and dried walnut shells, in which the water content was reduced to 1.7%. The threshold results for the two scenarios are almost the same, which indicates that humidity had a negligible effect on threshold for walnut shells in this experimental regime. When the water content is lower than 11.0%, the interparticle forces are dominated by adsorption forces, whereas at higher values the interparticle forces are dominated by much larger capillary forces. For materials with low equilibrium water content, like quartz sand, capillary forces dominate. When the interparticle forces are dominated by adsorption forces, the threshold does not increase with increasing relative humidity (RH) or water content. Only when the interparticle forces are dominated by capillary forces does the threshold start to increase with increasing RH/water content. Since tholins have a low methane content (0.3% at saturation, [Curtis, D. B., Hatch, C. D., Hasenkopf, C. A., et al., 2008. Laboratory studies of methane and ethane adsorption and nucleation onto organic particles: Application to Titan's clouds. Icarus, 195, 792. http://dx.doi.org/10.1016/j.icarus.2008.02.003]), we believe tholins would behave similarly to quartz sand when subjected to methane moisture.

Petrography, mineralogy, and geochemistry of deep gravelly sands in the Eyreville B core, Chesapeake Bay impact structure

USGS Publications Warehouse

Bartosova, Katerina; Gier, Susanne; Horton, J. Wright; Koeberl, Christian; Mader, Dieter; Dypvik, Henning

2010-01-01

The ICDP–USGS Eyreville drill cores in the Chesapeake Bay impact structure reached a total depth of 1766 m and comprise (from the bottom upwards) basement-derived schists and granites/pegmatites, impact breccias, mostly poorly lithified gravelly sand and crystalline blocks, a granitic slab, sedimentary breccias, and postimpact sediments. The gravelly sand and crystalline block section forms an approximately 26 m thick interval that includes an amphibolite block and boulders of cataclastic gneiss and suevite. Three gravelly sands (basal, middle, and upper) are distinguished within this interval. The gravelly sands are poorly sorted, clast supported, and generally massive, but crude size-sorting and subtle, discontinuous layers occur locally. Quartz and K-feldspar are the main sand-size minerals and smectite and kaolinite are the principal clay minerals. Other mineral grains occur only in accessory amounts and lithic clasts are sparse (only a few vol%). The gravelly sands are silica rich (~80 wt% SiO2). Trends with depth include a slight decrease in SiO2 and slight increase in Fe2O3. The basal gravelly sand (below the cataclasite boulder) has a lower SiO2 content, less K-feldspar, and more mica than the higher sands, and it contains more lithic clasts and melt particles that are probably reworked from the underlying suevite. The middle gravelly sand (below the amphibolite block) is finer-grained, contains more abundant clay minerals, and displays more variable chemical compositions than upper gravelly sand (above the block). Our mineralogical and geochemical results suggest that the gravelly sands are avalanche deposits derived probably from the nonmarine Potomac Formation in the lower part of the target sediment layer, in contrast to polymict diamictons higher in the core that have been interpreted as ocean-resurge debris flows, which is in agreement with previous interpretations. The mineralogy and geochemistry of the gravelly sands are typical for a passive continental margin source. There is no discernible mixing with marine sediments (no glauconite or Paleogene marine microfossils noted) during the impact remobilization and redeposition. The unshocked amphibolite block and cataclasite boulder might have originated from the outer parts of the transient crater.

[SUVA (Swiss Accident Insurance Fund) and silicosis. Silicosis in Switzerland. Development of technological dust control].

PubMed

Bachofen, G

1983-01-01

In Switzerland the technical measures against quartz dust started in 1948 when wet drilling was compulsoryly introduced, initially in underground mining. The miners using the first wet drilling machines had serious problems with water, and only with the introduction of carriage drilling machines in 1963 did the method fully break through. Dust caused by blasting operations and by loading of the resultant material was limited by ventilation and sprinkling of water. In 1966 the first full-face cutting machines were used, and it was necessary to install a dust chamber behind the drill from which dust could be taken to a dust arrester. The problem of dust limitation when using boom cutters at sectional areas of more than 20 sq. meters without a pilot tunnel has not been resolved. Since 1970, dust in quarries and stone-cutter workshops has been successfully combated by the use of exhaust pumps in combination with filters. The use of quartz sand to clean metal pieces (sandblast) was forbidden in 1960. Today, materials of the same value, but quartz-free, are available. In foundries, dust production can be limited by continuous automation and installation of exhaust pumps in moulding units. For more than 30 years now the technical equipment has been available for successful prevention of quartz dust emissions. However, at some plants it is still difficult to persuade the personnel to use the protective equipment.

Unusual holocene alluvial record from Rio Del Osos, Jemez Mountains, New Mexico: Paleoclimatic and archaeologic significance

Treesearch

Stephen A. Hall; Richard D. Periman

2007-01-01

The lower Rio del Oso valley is characterized by a single Holocene terrace that is formed by 3 to 5 m of largely overbank fine quartz sand dated by 22 radiocarbon dates between 4610 and 640 14C yrs BP making this one of the best dated sequences in the region. The alluvium contains seven cumulic A horizon paleosols, 5 to 62 cm thick, a remarkable feature seldom seen in...

Transport of strontium and cesium in simulated hanford tank waste leachate through quartz sand under saturated and unsaturated flow.

PubMed

Rod, Kenton A; Um, Wooyong; Flury, Markus

2010-11-01

We investigated the effects of water saturation and secondary precipitate formation on Sr and Cs transport through quartz sand columns under saturated and unsaturated flow. Column experiments were conducted at effective water saturation ranging from 0.2 to 1.0 under steady-state flow using either 0.1 M NaNO(3) or simulated tank waste leachate (STWL; 1 M NaNO(3) and 1 M NaOH) mimicking Hanford (Washington, USA) tank waste. In 0.1 M NaNO(3) columns, Sr transported like a conservative tracer, whereas Cs was retarded relative to Sr. The transport of Sr and Cs in the 0.1 M NaNO(3) columns under all water saturations could be described with the equilibrium convection-dispersion equation (CDE). In STWL columns, Sr mobility was significantly reduced compared to the 0.1 M NaNO(3) column, because Sr was incorporated into or sorbed to neo-formed secondary precipitates. Strontium sequestration by precipitates was confirmed by additional batch and electron micrograph analyses. In contrast(,) the transport of Cs was less affected by the STWL; retardation of Cs in STWL columns was similar to that found in 0.1 M NaNO(3) columns. Analysis of STWL column data revealed that both Sr and Cs breakthrough curves showed nonideal behavior that suggest nonequilibrium conditions, although nonlinear geochemical behavior cannot be ruled out.

Variations in dissolved organic nitrogen concentration in biofilters with different media during drinking water treatment.

PubMed

Zhang, Huining; Zhang, Kefeng; Jin, Huixia; Gu, Li; Yu, Xin

2015-11-01

Dissolved organic nitrogen (DON) is potential precursor of disinfection byproducts (DBPs), especially nitrogenous DBPs. In this study, we investigated the impact of biofilters on DON concentration changes in a drinking water plant. A small pilot plant was constructed next to a sedimentation tank in a drinking water plant and included activated carbon, quartz sand, anthracite, and ceramsite biofilters. As the biofilter layer depth increased, the DON concentration first decreased and then increased, and the variation in DON concentration differed among the biofilters. In the activated carbon biofilter, the DON concentration was reduced by the largest amount in the first part of the column and increased by the largest amount in the second part of the column. The biomass in the activated carbon filter was less than that in the quartz sand filter in the upper column. The heterotrophic bacterial proportion among bacterial flora in the activated carbon biofilter was the largest, which might be due to the significant reduction in DON in the first part of the column. Overall, the results indicate that the DON concentration in biofiltered water can be controlled via the selection of appropriate biofilter media. We propose that a two-layer biofilter with activated carbon in the upper layer and another media type in the lower layer could best reduce the DON concentration. Copyright © 2014 Elsevier Ltd. All rights reserved.

A note on the effect of fault gouge composition on the stability of frictional sliding

USGS Publications Warehouse

Summers, R.; Byerlee, J.

1977-01-01

The frictional properties of fault gouge have been studied at confining pressures to 6 kbars. If the gouge is composed of strong materials such as crushed granite or quartz sand, the frictional strength is high, and violent stick-slip occurs at confining pressures above approximately 1.5 kbars. If the gouge is composed of minerals such as illite, kaolinite, chlorite, or antigorite, which have weak bonding forces between the structural layers, the frictional strength is slightly lower, but violent stick-slip still occurs under high confining pressure. The expanding clays, montmorillonite and vermiculite, which have free water between their structural layers, slide stably at confining pressures as high as 6.25 kbars and exhibit low friction. A similar stable behavior with lowered strength is observed in water-saturated quartz sand when the water is confined within the fault zone during deformation. The results of this series of experiments support water being the stabilizing influence when it is either (1) trapped within or between rocks of low permeability and can provide a high pore pressure when the rocks are deformed, or (2) loosely bonded in a mineral structure, as in the hydrated clays, where it can produce a pseudo-pore pressure when the clay is compressed. In both these cases, the effective stress can be reduced and the deformation stabilized. ?? 1977.

Transport of the Pathogenic Prion Protein through Landfill Materials

PubMed Central

Jacobson, Kurt H.; Lee, Seunghak; McKenzie, Debbie; Benson, Craig H.; Pedersen, Joel A.

2009-01-01

Transmissible spongiform encephalopathies (TSEs, prion diseases) are a class of fatal neurodegenerative diseases affecting a variety of mammalian species including humans. A misfolded form of the prion protein (PrPTSE) is the major, if not sole, component of the infectious agent. Recent TSE outbreaks in domesticated and wild animal populations has created the need for safe and effective disposal of large quantities of potentially infected materials. Here, we report the results of a study to evaluate the potential for transport of PrPTSE derived from carcasses and associated wastes in a municipal solid waste (MSW) landfill. Column experiments were conducted to evaluate PrPTSE transport in quartz sand, two fine-textured burial soils currently used in landfill practice, a green waste residual material (a potential burial material), and fresh and aged MSW. PrPTSE was retained by quartz sand and the fine-textured burial soils, with no detectable PrPTSE eluted over more than 40 pore volumes. In contrast, PrPTSE was more mobile in MSW and green waste residual. Transport parameters were estimated from the experimental data and used to model PrPTSE migration in a MSW landfill. To the extent that the PrPTSE used mimics that released from decomposing carcasses, burial of CWD-infected materials at MSW landfills could provide secure containment of PrPTSE provided reasonable burial strategies (e.g., encasement in soil) are used. PMID:19368208

Remagnetization and Cementation of Unconsolidated Sediments in the Mallik 5L-38 Well (Canadian Arctic) by Solute Exclusion During Gas Hydrate Formation

NASA Astrophysics Data System (ADS)

Hamilton, T. S.; Enkin, R. J.; Esteban, L.

2007-05-01

Bulk magnetic properties provide a sensitive measure of sedimentary diagenesis related to the stability and growth of gas hydrates. The deposit at Mallik (Mackenzie Delta, Canadian Arctic) occurs in unconsolidated Tertiary sands, but is absent in interstratified silt layers. A detailed sampling of the JAPEX/JNOC/GSC Mallik 5L-38 core tested the use of magnetic properties for detecting diagenetic changes related to the hydrate. Petrographic studies reveal that the sands are well sorted and clean, with quartz > chert >> muscovite and little fines content. Excepting a few rare bands of indurated dolomite in the midst of the gas hydrate zone, there is little or no cementation in the sands. Detrital magnetite is the dominant magnetic mineral, comprising up to a few percent of the sand grain population. In contrast, the muddier layers have a somewhat different detrital grain composition, richer in lithic (sedimentary and metamorphic) grains, feldspar, and clays. They are extensively diagenetically altered (to as much as 30- 40%) and cemented with carbonates, clays, chlorite and the iron sulphide greigite (the dominant magnetic mineral). The greigite is recognized by its isotropic creamy-white reflectance, cubic to prismatic habit, and characteristic tarnish to faintly bluish bireflectant mackinawite. Habits range from disseminated cubes and colliform masses to inflationary massive sulphide veins and clots. Rare detrital grains of magnetite were observed among the silt grains, but never in a reaction relationship or overgrown. Instead the greigite has nucleated separately, in tensional fractures and granular masses up to 4 mm across. In this particular sediment sequence, being so quartz and chert rich, there is insufficient local source for the introduced cements (calcite, dolomite, greigite, clays, jarosite), so ions must have been introduced by fluid flow. Magnetic studies reveal a bi-modal character related to the lithology (sands versus silts) and their magnetic mineralogy. Silt samples are significantly stronger than sand samples in saturation magnetization and magnetic susceptibility. The silt samples have single-domain to pseudo-single domain coercivity ratios whereas the gas hydrate bearing sands have a more multi-domain nature. Sands with current gas hydrate concentrations > 80% have less magnetic material and single domain characteristics. The source of the greigite, carbonates, and other diagenetic minerals was apparently concentrated solutes excluded from formation waters by the freezing and formation of the water dominated gas hydrate. The hydrates served as a cementing agent for the unconsolidated sediments, allowing them to fracture. Some layers have been so inflated by the introduction carbonate and sulfide cements that they resemble hydrothermal tufa and skarns with floating sand grains. In the silts, the magnetic properties reflect the mixture of primary detrital magnetite and diagenetic greigite in various grain sizes and concentrations. At Mallik, the magnetic properties are sensitive to the diagenetic mineralogy and redox state associated with the transport of methane and pore fluids and the creation of gas hydrates. Hypersaline brines, produced by solute exclusion from pore waters, fractured and inflated less permeable sediments and forced rapid disequilibrium growth of greigite without dissolving primary detrital magnetite grains.

The Impact of Membrane Permeability and Dialysate Purity on Cardiovascular Outcomes

PubMed Central

Tӧz, Huseyin; Ozkahya, Mehmet; Duman, Soner; Demirci, Meltem Sezis; Cirit, Mustafa; Sipahi, Savas; Dheir, Hamad; Bozkurt, Devrim; Kircelli, Fatih; Ok, Ebru Sevinc; Erten, Sinan; Ertilav, Muhittin; Kose, Timur; Basci, Ali; Raimann, Jochen G.; Levin, Nathan W.; Ok, Ercan

2013-01-01

The effects of high-flux dialysis and ultrapure dialysate on survival of hemodialysis patients are incompletely understood. We conducted a randomized controlled trial to investigate the effects of both membrane permeability and dialysate purity on cardiovascular outcomes. We randomly assigned 704 patients on three times per week hemodialysis to either high- or low-flux dialyzers and either ultrapure or standard dialysate using a two-by-two factorial design. The primary outcome was a composite of fatal and nonfatal cardiovascular events during a minimum 3 years follow-up. We did not detect statistically significant differences in the primary outcome between high- and low-flux (HR=0.73, 95% CI=0.49 to 1.08, P=0.12) and between ultrapure and standard dialysate (HR=0.90, 95% CI=0.61 to 1.32, P=0.60). Posthoc analyses suggested that cardiovascular event-free survival was significantly better in the high-flux group compared with the low-flux group for the subgroup with arteriovenous fistulas, which constituted 82% of the study population (adjusted HR=0.61, 95% CI=0.38 to 0.97, P=0.03). Furthermore, high-flux dialysis associated with a lower risk for cardiovascular events among diabetic subjects (adjusted HR=0.49, 95% CI=0.25 to 0.94, P=0.03), and ultrapure dialysate associated with a lower risk for cardiovascular events among subjects with more than 3 years of dialysis (adjusted HR=0.55, 95% CI=0.31 to 0.97, P=0.04). In conclusion, this trial did not detect a difference in cardiovascular event-free survival between flux and dialysate groups. Posthoc analyses suggest that high-flux hemodialysis may benefit patients with an arteriovenous fistula and patients with diabetes and that ultrapure dialysate may benefit patients with longer dialysis vintage. PMID:23620396

Timing of lake-level changes for a deep last-glacial Lake Missoula: optical dating of the Garden Gulch area, Montana, USA

NASA Astrophysics Data System (ADS)

Smith, Larry N.; Sohbati, Reza; Buylaert, Jan-Pieter; Lian, Olav B.; Murray, Andrew; Jain, Mayank

2018-03-01

Glaciolacustrine sediments in the Clark Fork River valley at Garden Gulch, near Drummond, Montana, USA record highstand positions of the ice-dammed glacial Lake Missoula and repeated subaerial exposure. During these highstands the lake was at greater than 65% of its recognized maximum capacity. The initial lake transgression deposited a basal sand unit. Subsequent cycles of lake-level fluctuations are recorded by sequences of laminated and cross laminated silt, sand, and clay deformed by periglacial processes during intervening periods of lower lake levels. Optically stimulated luminescence (OSL) dating of quartz sand grains, using single-aliquot regenerative-dose procedures, was carried out on 17 samples. Comparison of infrared stimulated luminescence (IRSL) from K-rich feldspar to OSL from quartz for all the samples suggests that they were well bleached prior to deposition and burial. Ages for the basal sand and overlying glaciolacustrine exposure surfaces are indistinguishable within one standard deviation, and give a weighted mean age of 20.9 ± 1.3 ka (n = 11). Based on sedimentological and stratigraphic analysis we infer that the initial transgression, and at least six cycles of lake-level fluctuation, occurred over time scales of decades to ∼2 ka. Bioturbated sandy slopewash dated at 10.6 ± 0.9 ka and 11.9 ± 1.2 ka unconformably overlies the upper glaciolacustrine deposits. The uppermost sediments, above the glaciolacustrine section, are younger than the Glacier Peak tephra (13.7-13.4 cal ka B.P.), which was deposited across parts of the drained lake basin, but has not been found at Garden Gulch. Our study indicates that glacial Lake Missoula reached >65 percent of maximum capacity by about 20.9 ± 1.3 ka and either partially or completely drained twelve times from this position. Rapid lowering from the lake's highstand position due to ice-dam failure likely led to scour in the downstream portions of the glacial Lake Missoula basin and megafloods in the Channeled Scabland.

Imaging, Mapping and Monitoring Environmental Radionuclide Transport Using Compton-Geometry Gamma Camera

NASA Astrophysics Data System (ADS)

Bridge, J. W.; Dormand, J.; Cooper, J.; Judson, D.; Boston, A. J.; Bankhead, M.; Onda, Y.

2014-12-01

The legacy to-date of the nuclear disaster at Fukushima Dai-ichi, Japan, has emphasised the fundamental importance of high quality radiation measurements in soils and plant systems. Current-generation radiometers based on coded-aperture collimation are limited in their ability to locate sources of radiation in three dimensions, and require a relatively long measurement time due to the poor efficiency of the collimation system. The quality of data they can provide to support biogeochemical process models in such systems is therefore often compromised. In this work we report proof-of-concept experiments demonstrating the potential of an alternative approach in the measurement of environmentally-important radionuclides (in particular 137Cs) in quartz sand and soils from the Fukushima exclusion zone. Compton-geometry imaging radiometers harness the scattering of incident radiation between two detectors to yield significant improvements in detection efficiency, energy resolution and spatial location of radioactive sources in a 180° field of view. To our knowledge we are reporting its first application to environmentally-relevant systems at low activity, dispersed sources, with significant background radiation and, crucially, movement over time. We are using a simple laboratory column setup to conduct one-dimensional transport experiments for 139Ce and 137Cs in quartz sand and in homogenized repacked Fukushima soils. Polypropylene columns 15 cm length with internal diameter 1.6 cm were filled with sand or soil and saturated slowly with tracer-free aqueous solutions. Radionuclides were introduced as 2mL pulses (step-up step-down) at the column inlet. Data were collected continuously throughout the transport experiment and then binned into sequential time intervals to resolve the total activity in the column and its progressive movement through the sand/soil. The objective of this proof-of-concept work is to establish detection limits, optimise image reconstruction algorithms, and develop a novel approach to time-lapse quantification of radionuclide dynamics in the soil-plant system. The aim is to underpin the development of a new generation of Compton radiometers equipped to provide high resolution, dynamic measurements of radionuclides in terrestrial biogeochemical environments.

Central Asian sand seas climate change as inferred from OSL dating

NASA Astrophysics Data System (ADS)

Maman, Shimrit; Tsoar, Haim; Blumberg, Dan; Porat, Naomi

2014-05-01

Luminescence dating techniques have become more accessible, widespread, more accurate and support studies of climate change. Optically stimulated luminescence (OSL) is used to determine the time elapsed since quartz grains were last exposed to sunlight, before they were buried and the dune stabilized. Many sand seas have been dated extensively by luminescence, e.g., the Kalahari, Namib the Australian linear dunes and the northwestern Negev dune field, Israel. However, no ages were published so far from the central Asian sand seas. The lack of dune stratigraphy and numerical ages precluded any reliable assessment of the paleoclimatic significance of dunes in central Asia. Central Asian Sand seas (ergs) have accumulated in the Turan basin, north-west of the Hindu Kush range, and span from south Turkmenistan to the Syr-Darya River in Kazakhstan. These ergs are dissected by the Amu-Darya River; to its north lies the Kyzylkum (red sands) and to its south lies the Karakum (black sands). Combined, they form one of the largest sand seas in the world. This area is understudied, and little information has been published regarding the sands stabilization processes and deposition ages. In this study, OSL ages for the Karakum and Kyzylkum sands are presented and analysis of the implications of these results is provided. Optical dates obtained in this study are used to study the effects climatic changes had on the mobility and stability of the central Asian sand seas. Optically stimulated luminescence ages derived from the upper meter of the interdune of 14 exposed sections from both ergs, indicate extensive sand and dune stabilization during the mid-Holocene. This stabilization is understood to reflect a transition to a warmer, wetter, and less windy climate that generally persisted until today. The OSL ages, coupled with a compilation of regional paleoclimatic data, corroborate and reinforce the previously proposed Mid-Holocene Liavliakan phase, known to reflect a warmer, wetter, and less windy climate that persists until today and resulted in dune stabilization around the Mid-Holocene. This study, solidifies our results regarding the Kyzylkum and Karakum sand seas dynamics, ages, and emphasizes the importance of regional climatic control on aeolian activity.

Photolytic and photocatalytic degradation of quinclorac in ultrapure and paddy field water: identification of transformation products and pathways.

PubMed

Pareja, Lucía; Pérez-Parada, Andrés; Agüera, Ana; Cesio, Verónica; Heinzen, Horacio; Fernández-Alba, Amadeo R

2012-05-01

Quinclorac (QNC) is an effective but rather persistent herbicide commonly used in rice production. This herbicide presents a mean persistence in the environment so its residues are considered of environmental relevance. However, few studies have been conducted to investigate its environmental behavior and degradation. In the present work, direct photolysis and TiO(2) photocatalysis of the target compound in ultrapure and paddy field water were investigated. After 10h photolysis in ultrapure water, the concentration of QNC declined 26% and 54% at 250 and 700 W m(-2), respectively. However, the amount of quinclorac in paddy field water remained almost constant under the same irradiation conditions. QNC dissipated completely after 40 min of TiO(2) photocatalysis in ultrapure water, whereas 130 min were necessary to degrade 98% of the initial concentration in paddy field water. Possible QNC photolytic and photocatalytic degradation pathways are proposed after structure elucidation of the main transformation products, through liquid chromatography-electrospray ionization-quadrupole time-of-flight mass spectrometry and exact mass measurements. Pyridine ring hydroxylation at C-9 followed by ring opening and/or oxidative dechlorination were the key steps of QNC degradation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Sedimentary Framework of an Inner Continental Shelf Sand-Ridge System, West-Central Florida

NASA Astrophysics Data System (ADS)

Locker, S. D.; Hine, A. C.; Wright, A. K.; Duncan, D. S.

2002-12-01

The west-central Florida inner continental shelf is a dynamic environment subject to current flows on a variety of temporal and spatial scales. A site survey program, undertaken in support of the Office of Naval Research's Mine Burial prediction program, is focused on the sedimentary framework and sediment accumulation patterns in 10-18 meters water depth. Our specific goals are to image the shallow subsurface and to monitor changes in bedform distribution patterns that coincide with physical processes studies ongoing in the area. Methods of study include side-scan sonar imaging, boomer and chirp subbottom profiling, and sedimentary facies analysis using surface sediment sampling and vibracoring. A well-defined sand-ridge system was imaged, trending oblique to the west-Florida coastline. The side-scan clearly shows that there is extensive three-dimensional structure within these large-scale NW-SE trending sedimentary bedforms. The sand ridges commonly are approximately 1 km wide and 4-8 km in length. The characteristics of these ridges are distinctly different than the sand ridges in < 8 m water that we have previously studied. Ridges in the offshore area tend to be thicker, have a flatter morphology, and exhibit fewer smaller-scale sand waves. Sand-ridge thickness ranges 2-3 meters, and typically consists of fining upward medium to fine quartz sand facies with occasional centimeter-scale coarser-grained carbonate-rich intervals. Time series investigations tracking the shift in position of the sand ridge margins have found undetectable net annual movement. However significant resuspension and bedform development accompanies high-energy events such as winter cold front passage. Thus the large-scale bedforms (sand ridges) are in a state of dynamic equilibrium with the average annual hydrodynamic regime. Repeated field surveys will focus on monitoring small-scale sedimentological and stratal framework changes that will be integrated with the quantitative process studies.

Chemistry of sands from the modern Indus River and the Archean Witwatersrand basin: Implications for the composition of the Archean atmosphere

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maynard, J.B.; Ritger, S.D.; Sutton, S.J.

1991-03-01

Both the Indus River and the Witwatersrand basin contain sand with grains of detrital uraninite. Because this mineral is easily oxidized, its presence in Archean strata as a detrital particle has been used as evidence for a low-oxygen atmosphere before 2.5 Ga. However, its presence in modern sand from the Indus River system has been used to argue that detrital uraninite does not provide information about the oxygen concentration of Earth's early atmosphere. Petrographic and chemical study of sand from these two sources reveals differences that suggest the modern Indus sand cannot be used as an analog for the Archeanmore » Witwatersrand occurrences. The Witwatersrand quartzites are depleted in Ca, Mg, and Na, indicating that the original sand from which they formed had been subjected to intense weathering. The chemical index of alteration (CIA), a commonly used indicator of degree of weathering, yields an average value of about 0.80 for Witwatersrand quartzites, comparable to modern tropical streams such as the Orinoco that drain deeply weathered terrains under tropical conditions (CIA=0.75). In contrast, the CIA for Indus sand is 0.45, indicating virtually no chemical weathering. The significance of Archean quartz-pebble conglomerates is not just that they contain unstable detrital phases like uraninite and pyrite, but that these particles are associated with rocks whose compositions suggest intense weathering. These conglomerates must have been subjected to intense weathering under tropical conditions, either in their source area or at the site of deposition, and the preservation of minerals like uraninite such conditions is indeed strong evidence for a low-oxygen atmosphere.« less

Characterization and constructive utilization of sludge produced in clari-flocculation unit of water treatment plant

NASA Astrophysics Data System (ADS)

Ahmad, Tarique; Ahmad, Kafeel; Alam, Mehtab

2018-03-01

All water treatment plants produce waste/residue amid the treatment of raw water. This study selectively investigates the clariflocculator sludge for its physicochemical characteristics and potential reuse options. Sieve analysis, XRF, SEM, XRD, FTIR, and TG-DTA instrumental techniques have been used to characterize the sludge sample. Results show that clariflocculator sludge contains about 78% fine sand having grain size range 150-75 μm. SiO2, Al2O3, Fe2O3 and CaO constitute the maximum percentage of chemical compounds present in the sludge and quartz is the main crystalline phase of the sludge. Recycling and reuse of this sludge, especially, as fine sand in preparing mortar, concrete mix and other civil engineering products would pave the way for constructive utilization with safe and sustainable sludge management strategies.

Compressor cascade performance deterioration caused by sand ingestion

NASA Technical Reports Server (NTRS)

Tabakoff, W.; Balan, C.

1982-01-01

Airfoil cascade erosion and performance deterioration was investigated in a gas particle cascade tunnel. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand. The results of the experimental measurements are presented to show the change in the blade surface erosion, pressure distribution and the total loss coefficient with erosion. The surface quality of the blades exposed to particulate flows are changing the material surfaces. With time, the surface roughness increases and leads to a decrease in engine performance. It was found that the surface roughness values increase asymptotically to a maximum value with increased erosion. The experimental results indicate that the roughness parameters correlate well against the mass of particles impacting unit area of the surface. Such a correlation is useful in aerodynamics and performance computations in turbomachinery.

Phosphorus Elimination at Sodium Silicate from Quartz Sand Roasted with Complexation using Chitosan-EDTA

NASA Astrophysics Data System (ADS)

Wahyuningsih, S.; Ramelan, A. H.; Suharty, N. S.; Handayani, M.; Firdiyono, F.; Sulistiyono, E.; Munawaroh, H.; Sari, P. P.; Kristiawan, Y. R.

2018-03-01

A phosphorus elimination from sodium silicate solution has been studied. Phosphorus elimination was performed by adding chitosan-EDTA to remove cation phosphorus. Characterization of chitosan-EDTA material was performed using FT-IR, while the decreasing level of phosphorus content was analyzed by quantitative analysis using spectrophotometer UV-Vis refers to SNI 06-6989-2004. The results showed that the content of the sodium silicate can be reduced up to 67.1% through Chitosan-EDTA complexation with phosphorus.

Desorption and Transformation of Nitroaromatic (TNT) and Nitramine (RDX and HMX) Explosive Residues on Detonated Pure Mineral Phases

DTIC Science & Technology

2011-11-01

surface area measurements were used to compare the pristine and detonated mineral surfaces and to determine if the extreme heat and/or pressures of...gas (N2) in a liquid nitrogen atmosphere (−194.8°C). Results from six relative pressure points were reduced to surface area values applying BET theory...include the minerals quartz, calcite, and dolomite . However, in some detonated Ottawa sand samples the highest intensity peak for calcite at 29° 2Θ

A Wind Dependent Desert Aerosol Model: Radiative Properties

DTIC Science & Technology

1988-04-19

Source Regions and Transport Characteristics 5 2.2 Size Distributions 6 2.3 Composition 8 2.4 Effects of Wind 10 2.5 Indices of Refraction 12 2.5.1 An...Hematite Concentrations of 0, 5, and 10 %, (a) O-Ray and (b) E-Ray 44 8 . Imaginary Part of the Index of Refraction for Sand Having Hematite...rarbonaceous Material 31 8 . Indices of Refraction "or Ammonium Sulfate 32 9. Indices of Refraction for the 0-Ray of Quartz 35 10 . Indices of Refraction for the

Installation Restoration Program. Phase 2. Confirmation/Quantification Stage 2, Moody Air Force Base, Georgia. Appendices. Volume 1

DTIC Science & Technology

1988-11-01

Light gray NB, clayey (kaolin). Poetv al - quartz mad to fine sand, mod. (0 Locking Cap plastic , saturated. 3 COMPILED BY B. Painter (EWM) t DATE 11-21...Painter (EUM) -SAMPLE PNTAINSOIL DESCRIIPTION COMMENTS ZTEST NAME. GRADATION OR PLASTICITY ,. DEPTH Of CASING, W ~ 1NPARTICLE SIZE DISTRIBUTION. COLOR...L. Grayish orange 10 YR 7/4. quart. RNDEVAI: very tine Sandy clay, dense, DIAMETER: 2-inrh Srhe So PVC moderately plastics dry. DEPTH: 2 - fenot[ 1

Demonstration of the Attributes of Multi-increment Sampling and Proper Sample Processing Protocols for the Characterization of Metals on DoD Facilities

DTIC Science & Technology

2013-06-01

lenses of unconsolidated sand and rounded river gravel overlain by as much as 5 m of silt. Gravel consists mostly of quartz and metamorphic rock with...iii LIST OF FIGURES Page Figure 1. Example of multi-increment sampling using a systematic-random sampling design for collecting two separate...The small arms firing Range 16 Record berms at Fort Wainwright. .................... 25 Figure 9. Location of berms sampled using ISM and grab

Abrasion by aeolian particles: Earth and Mars

NASA Technical Reports Server (NTRS)

Greeley, R.; Marshall, J. R.; White, B. R.; Pollack, J. B.; Marshall, J.; Krinsley, D.

1984-01-01

Estimation of the rate of aeolian abrasion of rocks on Mars requires knowledge of: (1) particle flux, (2) susceptibilities to abrasion of various rocks, and (3) wind frequencies on Mars. Fluxes and susceptibilities for a wide range of conditions were obtained in the laboratory and combined with wind data from the Viking meteorology experiment. Assuming an abundant supply of sand-sized particles, estimated rates range up to 2.1 x 10 to the minus 2 power cm of abrasion per year in the vicinity of Viking Lander 1. This rate is orders of magnitude too great to be in agreement with the inferred age of the surface based on models of impact crater flux. The discrepancy in the estimated rate of abrasion and the presumed old age of the surface cannot be explained easily by changes in climate or exhumation of ancient surfaces. The primary reason is thought to be related to the agents of abrasion. At least some sand-sized (approx. 100 micrometers) grains appear to be present, as inferred from both lander and orbiter observations. High rates of abrasion occur for all experimental cases involving sands of quartz, basalt, or ash. However, previous studies have shown that sand is quickly comminuted to silt- and clay-sized grains in the martian aeolian regime. Experiments also show that these fine grains are electrostatically charged and bond together as sand-sized aggregates. Laboratory simulations of wind abrasion involving aggregates show that at impact velocities capable of destroying sand, aggregates from a protective veneer on the target surface and can give rise to extremely low abrasion rates.

Bioburden control for Space Station Freedom's Ultrapure Water System

NASA Technical Reports Server (NTRS)

Snodgrass, Donald W.; Rodgers, Elizabeth B.; Obenhuber, Don; Huff, Tim

1991-01-01

Bioburden control is one of the challenges for the Ultrapure Water System on Space Station Freedom. Bioburden control must enable the system to deliver water with a low bacterial count as well as maintain biological contamination at a manageable level, to permit continued production of quality water. Ozone has been chosen as the primary means of Bioburden control. Planned tests to determine the effectiveness of ozone on free-floating microbes and biofilms are described.

Effects of Full-Scale Beach Renovation on Fecal Indicator Levels in Shoreline Sand and Water

PubMed Central

Hernandez, Rafael J.; Hernandez, Yasiel; Jimenez, Nasly H.; Piggot, Alan M.; Klaus, James S.; Feng, Zhixuan; Reniers, Ad; Solo-Gabriele, Helena M.

2013-01-01

Recolonization of enterococci, at a non-point source beach known to contain high background levels of bacteria, was studied after a full-scale beach renovation project. The renovation involved importation of new exogenous sand, in addition to infrastructure improvements. The study's objectives were to document changes in sand and water quality and to evaluate the relative contribution of different renovation activities towards these changes. These objectives were addressed: by measuring enterococci levels in the sand and fecal indicator bacteria levels (enterococci and fecal coliform) in the water, by documenting sediment characteristics (mineralogy and biofilm levels), and by estimating changes in observable enterococci loads. Analysis of enterococci levels on surface sand and within sediment depth cores were significantly higher prior to beach renovation (6.3 to 72 CFU/g for each sampling day) when compared to levels during and after beach renovation (0.8 CFU/g to 12 CFU/g) (p<0.01). During the renovation process, sand enterococci levels were frequently below detection limits (<0.1 CFU/g). For water, exceedances in the regulatory thresholds that would trigger a beach advisory decreased by 40% for enterococci and by 90% for fecal coliform. Factors that did not change significantly between pre- and post- renovation included the enterococci loads from animals (approx. 3 × 1011 CFU per month). Factors that were observed to change between pre- and post- renovation activities included: the composition of the beach sand (64% versus 98% quartz, and a significant decrease in biofilm levels) and loads from direct stormwater inputs (reduction of 3 × 1011 CFU per month). Overall, this study supports that beach renovation activities contributed to improved sand and water quality resulting in a 50% decrease of observable enterococci loads due to upgrades to the stormwater infrastructure. Of interest was that the change in the sand mineralogy also coincided with changes in biofilm levels. More work is needed to evaluate the relationships between beach sand mineralogy, biofilm characteristics, and the retention of fecal indicator bacteria in sand. PMID:24183401

Effects of full-scale beach renovation on fecal indicator levels in shoreline sand and water.

PubMed

Hernandez, Rafael J; Hernandez, Yasiel; Jimenez, Nasly H; Piggot, Alan M; Klaus, James S; Feng, Zhixuan; Reniers, Ad; Solo-Gabriele, Helena M

2014-01-01

Recolonization of enterococci, at a non-point source beach known to contain high background levels of bacteria, was studied after a full-scale beach renovation project. The renovation involved importation of new exogenous sand, in addition to infrastructure improvements. The study's objectives were to document changes in sand and water quality and to evaluate the relative contribution of different renovation activities towards these changes. These objectives were addressed: by measuring enterococci levels in the sand and fecal indicator bacteria levels (enterococci and fecal coliform) in the water, by documenting sediment characteristics (mineralogy and biofilm levels), and by estimating changes in observable enterococci loads. Analysis of enterococci levels on surface sand and within sediment depth cores were significantly higher prior to beach renovation (6.3-72 CFU/g for each sampling day) when compared to levels during and after beach renovation (0.8-12 CFU/g) (P < 0.01). During the renovation process, sand enterococci levels were frequently below detection limits (<0.1 CFU/g). For water, exceedances in the regulatory thresholds that would trigger a beach advisory decreased by 40% for enterococci and by 90% for fecal coliform. Factors that did not change significantly between pre- and post- renovation included the enterococci loads from animals (approx. 3 × 10(11) CFU per month). Factors that were observed to change between pre- and post- renovation activities included: the composition of the beach sand (64% versus 98% quartz, and a significant decrease in biofilm levels) and loads from direct stormwater inputs (reduction of 3 × 10(11) CFU per month). Overall, this study supports that beach renovation activities contributed to improved sand and water quality resulting in a 50% decrease of observable enterococci loads due to upgrades to the stormwater infrastructure. Of interest was that the change in the sand mineralogy also coincided with changes in biofilm levels. More work is needed to evaluate the relationships between beach sand mineralogy, biofilm characteristics, and the retention of fecal indicator bacteria in sand. Copyright © 2013 Elsevier Ltd. All rights reserved.

Gold placer and Quaternary stratigraphy of the Jabal Mokhyat area, southern Najd Province, Kingdom of Saudi Arabia

USGS Publications Warehouse

Schmidt, D.L.; Puffett, W.P.; Campbell, W.L.; Al-Koulak, Z. H.

1981-01-01

An ancient gold placer at Jabal Mokhyat (lat 20?12.2'N., long 43?28'E.), about 90 km east of Qalat Bishah in the southern Najd Province, Kingdom of Saudi Arabia, was studied in 1973. Seven hundred and twenty-eight samples in 25 measured sections were collected along trenches and pits 2.5 m in depth and 2,600 m in total length. Alluvium was thicker than the excavation depth along about 50 percent of the trench length. The average gold content was 4.4 mg per m3, and the highest grade trench contained 40 mg gold per m 3. Because fine particulate gold is rare in the alluvium, a few large particles, 1 to 5 mm in diameter, greatly affected the sampling results. The ancient placer diggings are in small headwater wadis distributed over a 30-km 2 area, and the total dug area is about 1.2 km2. The placer produced an estimated 50 kg of gold and was worked about 2,600 + 250 years ago. The potential for a present-day placer operation is small. The gold is sparsely distributed in locally derived, flood-deposited, immature gravels throughout a stratigraphic section that consists of 1) calichified, saprolitic bedrock of Precambrian age; 2) basal, intensely calichified, saprolitic gravel (0-3 m thick) of Pleistocene age; 3) disconformable, slightly consolidated gravel and sand (0-1 m thick) of late Pleistocene age containing sparse, disseminated caliche; 4) firm loessic silt (0-1 m thick) of early Holocene age; and 5) loose sand and gravel (0.3-1 m thick) of late Holocene age. The loessic silt accumulated during the Holocene pluvial. The top of the loessic silt unit is dated at about 6,000 years B.P. by using charcoal from hearths of ancient man. Following the Holocene pluvial, the climate became arid, and extreme desiccation resulted in abundant eolian sand that progressively diluted the late Holocene gravels. The remnants of the pre-Holocene stratigraphy suggest similar climatic cycles during the Pleistocene. Abundant, sparsely mineralized, gold-bearing quartz veins (0-1 m wide) were the source of the placer gold. These late Proterozoic veins have hydrothermally altered wall-rock zones (1-5 m wide). The veins are dispersed over an area of 50 km 2. Though many veins were prospected in ancient times and some were slightly worked, only the Mokhyat ancient mine, located on a quartz-vein zone 30 m wide by 200 m long, was extensively worked. The quartz contains chalcopyrite, galena, sphalerite, tetrahedrite, an unidentified bismuth mineral, and small amounts of dispersed gold. The fissure quartz veins lie at the complexly splayed, terminal end of a small northwest-trending Najd fault that elsewhere along strike has ii km of left-lateral displacement. Most large veins are in north-trending vertical fractures where the stresses were distributed along an older, north-trending structural grain in andesitic greenstone terrane. Subhorizontal fracture sets contain conspicuous, well-developed gold-bearing quartz veins and associated alteration zones. These attest to the shallowness and youthfulness of mineralization during latest Precambrian time. Late Precambrian granitic plutons (625-600 m.y. old) had been deeply eroded before the gold minerals were emplaced; hence, the gold is not related to granitic plutonism. Abundant, widely distributed diabasic dikes associated with the Najd faulting event of latest Precambrian age were probably the heat source for the hydrothermal convection system and possibly the source of the gold.

Genesis Ultrapure Water Megasonic Wafer Spin Cleaner

NASA Technical Reports Server (NTRS)

Allton, Judith H.; Stansbery, Eileen K.; Calaway, Michael J.; Rodriquez, Melissa C.

2013-01-01

A device removes, with high precision, the majority of surface particle contamination greater than 1-micron-diameter in size from ultrapure semiconductor wafer materials containing implanted solar wind samples returned by NASA's Genesis mission. This cleaning device uses a 1.5-liter/minute flowing stream of heated ultrapure water (UPW) with 1- MHz oscillating megasonic pulse energy focused at 3 to 5 mm away from the wafer surface spinning at 1,000 to 10,000 RPM, depending on sample size. The surface particle contamination is removed by three processes: flowing UPW, megasonic cavitations, and centripetal force from the spinning wafer. The device can also dry the wafer fragment after UPW/megasonic cleaning by continuing to spin the wafer in the cleaning chamber, which is purged with flowing ultrapure nitrogen gas at 65 psi (.448 kPa). The cleaner also uses three types of vacuum chucks that can accommodate all Genesis-flown array fragments in any dimensional shape between 3 and 100 mm in diameter. A sample vacuum chuck, and the manufactured UPW/megasonic nozzle holder, replace the human deficiencies by maintaining a consistent distance between the nozzle and wafer surface as well as allowing for longer cleaning time. The 3- to 5-mm critical distance is important for the ability to remove particles by megasonic cavitations. The increased UPW sonication time and exposure to heated UPW improve the removal of 1- to 5-micron-sized particles.

Evolution of crystalline target rocks and impactites in the chesapeake bay impact structure, ICDP-USGS eyreville B core

USGS Publications Warehouse

Horton, J. Wright; Kunk, Michael J.; Belkin, Harvey E.; Aleinikoff, John N.; Jackson, John C.; Chou, I.-Ming

2009-01-01

The 1766-m-deep Eyreville B core from the late Eocene Chesapeake Bay impact structure includes, in ascending order, a lower basement-derived section of schist and pegmatitic granite with impact breccia dikes, polymict impact breccias, and cataclas tic gneiss blocks overlain by suevites and clast-rich impact melt rocks, sand with an amphibolite block and lithic boulders, and a 275-m-thick granite slab overlain by crater-fill sediments and postimpact strata. Graphite-rich cataclasite marks a detachment fault atop the lower basement-derived section. Overlying impactites consist mainly of basement-derived clasts and impact melt particles, and coastal-plain sediment clasts are underrepresented. Shocked quartz is common, and coesite and reidite are confirmed by Raman spectra. Silicate glasses have textures indicating immiscible melts at quench, and they are partly altered to smectite. Chrome spinel, baddeleyite, and corundum in silicate glass indicate high-temperature crystallization under silica undersaturation. Clast-rich impact melt rocks contain α-cristobalite and monoclinic tridymite. The impactites record an upward transition from slumped ground surge to melt-rich fallback from the ejecta plume. Basement-derived rocks include amphibolite-facies schists, greenschist(?)-facies quartz-feldspar gneiss blocks and subgreenschist-facies shale and siltstone clasts in polymict impact breccias, the amphibolite block, and the granite slab. The granite slab, underlying sand, and amphibolite block represent rock avalanches from inward collapse of unshocked bedrock around the transient crater rim. Gneissic and massive granites in the slab yield U-Pb sensitive high-resolution ion microprobe (SHRIMP) zircon dates of 615 ± 7 Ma and 254 ± 3 Ma, respectively. Postimpact heating was <~350 °C in the lower basement-derived section based on undisturbed 40Ar/39Ar plateau ages of muscovite and <~150 °C in sand above the suevite based on 40Ar/39Ar age spectra of detrital microcline.

Depostional systems, provenance, and sequence stratigraphy, Carter and [open quotes]Millerella[close quotes] sandstones of northeast Mississippi

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cleaves, A.W. II

1993-09-01

The subsurface [open quotes]Millerella[close quotes] and Carter sandstones (middle Chesterian) of the Black Warrior basin represent the highest units of the thick Muldon clastics deltaic facies tract. Lowstand marine conditions during Carter deposition allowed for southeastwardly progradation of five distinct deltaic lobe complexes onto the stable northern shelf of the basin. With each of these lobes, both an [open quotes]A[close quotes] (upper) and a [open quotes]B[close quotes] (lower) reservoir unit can be identified. The [open quotes]B[close quotes] sandstone produces from delta-front sheet sands, channel-mouth bars, and possible bar fingers of river-dominated deltas. The more prolific [open quotes]A[close quotes] subdivision containsmore » reservoirs in upper delta-plain point bars, crevasse splays, and distributary channel fills. The most easterly of the lobes, preserved in the Bean's Ferry field of Itawamba County, comprises an amalgamated valley-fill facies that removed a maximum of 250 ft (76 m) of lower Bangor platform carbonates. In contrast, the [open quotes]Millerella[close quotes] sandstone is a series of unconnected pods that formed as marine-reworked sand bodies during a eustatic rise in sea level. The average detrital sand grain composition for four cores taken in Monroe County is 94.7% monocrystalline quartz, 2.9% polycrystalline quartz, 1.6% albite feldspar, 0.1% low-rank metamorphic rock fragments, 0.5 chert, and 0.2% muscovite. These data indicate that neither the Ozark uplift nor the Ouachita orogen could have acted as the principal source area for the Carter and [open quotes]Millerella[close quotes] sandstones. More likely, the sedimentary-igneous terrains along the northern margin of the Illinois basin served this function. A major eustatic lowstand brought this mineralogically mature sediment across the Illinois basin through incised valleys to the northern self of the Black Warrior basin.« less

Influence of gravity on transport and retention of representative engineered nanoparticles in quartz sand.

PubMed

Cai, Li; Zhu, Jinghan; Hou, Yanglong; Tong, Meiping; Kim, Hyunjung

2015-10-01

Four types of NPs: carbon nanotubes and graphene oxide (carbon-based NPs), titanium dioxide and zinc oxide metal-oxide NPs, were utilized to systematically determine the influence of gravity on the transport of NPs in porous media. Packed column experiments for two types of carbon-based NPs were performed under unfavorable conditions in both up-flow (gravity-negative) and down-flow (gravity-positive) orientations, while for two types of metal-oxide NPs, experiments were performed under both unfavorable and favorable conditions in both up-flow and down-flow orientations. Both breakthrough curves and retained profiles of two types of carbon-based NPs in up-flow orientation were equivalent to those in down-flow orientation, indicating that gravity had negligible effect on the transport and retention of carbon-based NPs under unfavorable conditions. In contrast, under both unfavorable and favorable conditions, the breakthrough curves for two types of metal-oxide NPs in down-flow orientation were lower relative to those in up-flow orientation, indicating that gravity could decrease the transport of metal-oxide NPs in porous media. The distinct effect of gravity on the transport and retention of carbon-based and metal-oxide NPs was mainly attributed to the contribution of gravity to the force balance on the NPs in quartz sand. The contribution of gravity was determined by the interplay of the density and sizes of NP aggregates under examined solution conditions. Copyright © 2015 Elsevier B.V. All rights reserved.

Diagenesis of an 'overmature' gas reservoir: The Spiro sand of the Arkoma Basin, USA

USGS Publications Warehouse

Spotl, C.; Houseknecht, D.W.; Burns, S.J.

1996-01-01

The Spiro sand is a laterally extensive thin sandstone of earliest Atokan (Pennsylvanian) age that forms a major natural gas reservoir in the western Arkoma Basin, Oklahoma. Petrographic analysis reveals a variety of diagenetic alterations, the majority of which occurred during moderate to deep burial. Early diagenetic processes include calcite cementation and the formation of Fe-clay mineral peloids and coatings around quartz framework grains. These clays, which underwent transformation to well-crystallized chamosite [polytype Ib(?? = 90??)] on burial, are particularly abundant in medium-grained channel sandstones, whereas illitic clays are predominant in fine-grained interchannel sandstones. Subsequent to mechanical compaction, saddle ankerite precipitated in the reservoir at temperatures in excess of 70??C. Crude oil collected in favourable structural locations during and after ankeritization. Whereas hydrocarbons apparently halted inorganic diagenesis in oil-saturated zones, cementation continued in the underlying water-saturated zones. As reservoir temperatures increased further, hydrocarbons were cracked and a solid pyrobitumen residue remained in the reservoir. At temperatures exceeding ???140-150??C, non-syntaxial quartz cement, ferroan calcite and traces of dickite(?) locally reduced the reservoir quality. Local secondary porosity was created by carbonate cement dissolution. This alteration post-dated hydrocarbon emplacement and is probably related to late-stage infiltration of freshwater along 'leaky' faults. The study shows that the Spiro sandstone locally retained excellent porosities despite deep burial and thermal conditions that correspond to the zone of incipient very low grade metamorphism.

Laboratory-scale study of possible use of residual sludge from glass sand beneficiation

NASA Astrophysics Data System (ADS)

Prikryl, Richard; Weishauptova, Zuzana; Zach, Jaroslav; Kozlovcev, Petr

2016-04-01

Beneficiation of quartz sand from sedimentary deposits for glass sands results in significant amounts of under-size fraction, a sludge rich in clay minerals. This sludge is considered as a waste and is returned in mined-out spaces for a simple rehabilitation, which is also the case of one of the largest glass sand production areas in the Czech Republic. The amount of produced waste sludge in the studied area (glass sand works in Provodín area, Bohemian Cretaceous Basin) is about 20 kt per year. In the recent study, we have focused on possible employment of this waste material for three applications: (1) a clay component in a raw material mixture for making of hydraulic lime, (2) a kaolinite absorbent, and (3) a geotechnical material. The sampled sludge was primarily analysed for mineralogical and chemical composition, mechanical and physical properties, the specific surface area, and parameters of pore space. X-ray analysis proved the presence of kaolinite, illite (both WCI and PCI), quartz, and accessory microcline. According to silicate analysis, the material is composed of SiO2 (80.52 wt. %), Al2O3 (11.36 wt. %), and K2O (2.14 wt. %). For its potential use as an artificial admixture for hydraulic lime production, the studied material was mixed with pure limestone in ratio of 10, 15, 20, and/or 25 wt. %. The experimental mixtures were burnt in the temperature range from 850 to 1,200°C. XRD was employed for the detection of newly formed phases showing formation of hydraulic phase such as C2S, C3A, C4AF starting from the 1050°C burning temperature. Peak burning temperature significantly influenced amount of individual phases in the burnt product. Second possible mode of use of the investigated waste material focused on its application as a sorbent. Pore space and specific surface area characteristics (SBET 7.4 sq. m/g) range this material to the group of low grade kaolinite-dominated adsorbents. Thermal treatment (burning of raw waste material at temperatures of 500°C and/or 900°C) lead to rapid deterioration of specific surface area, probably due to the structural and phase changes of dominant clay minerals. The latest considered use in the field of geotechnical applications proved possible employment of the studied material as a sealing clay for smaller dams, ponds and/or as a geotechnical barrier for waste dumps.

Coastal geology and recent origins for Sand Point, Lake Superior

USGS Publications Warehouse

Fisher, Timothy G.; Krantz, David E.; Castaneda, Mario R.; Loope, Walter L.; Jol, Harry M.; Goble, Ronald J.; Higley, Melinda C.; DeWald, Samantha; Hansen, Paul

2014-01-01

Sand Point is a small cuspate foreland located along the southeastern shore of Lake Superior within Pictured Rocks National Lakeshore near Munising, Michigan. Park managers’ concerns for the integrity of historic buildings at the northern periphery of the point during the rising lake levels in the mid-1980s greatly elevated the priority of research into the geomorphic history and age of Sand Point. To pursue this priority, we recovered sediment cores from four ponds on Sand Point, assessed subsurface stratigraphy onshore and offshore using geophysical techniques, and interpreted the chronology of events using radiocarbon and luminescence dating. Sand Point formed at the southwest edge of a subaqueous platform whose base is probably constructed of glacial diamicton and outwash. During the post-glacial Nipissing Transgression, the base was mantled with sand derived from erosion of adjacent sandstone cliffs. An aerial photograph time sequence, 1939–present, shows that the periphery of the platform has evolved considerably during historical time, infl uenced by transport of sediment into adjacent South Bay. Shallow seismic refl ections suggest slump blocks along the leading edge of the platform. Light detection and ranging (LiDAR) and shallow seismic refl ections to the northwest of the platform reveal large sand waves within a deep (12 m) channel produced by currents fl owing episodically to the northeast into Lake Superior. Ground-penetrating radar profi les show transport and deposition of sand across the upper surface of the platform. Basal radiocarbon dates from ponds between subaerial beach ridges range in age from 540 to 910 cal yr B.P., suggesting that Sand Point became emergent during the last ~1000 years, upon the separation of Lake Superior from Lakes Huron and Michigan. However, optically stimulated luminescence (OSL) ages from the beach ridges were two to three times as old as the radiocarbon ages, implying that emergence of Sand Point may have begun earlier, ~2000 years ago. The age discrepancy appears to be the result of incomplete bleaching of the quartz grains and an exceptionally low paleodose rate for the OSL samples. Given the available data, the younger ages from the radiocarbon analyses are preferred, but further work is necessary to test the two age models.

Modern sedimentary facies, depositional environments, and major controlling processes on an arid siliciclastic coast, Al qahmah, SE Red Sea, Saudi Arabia

NASA Astrophysics Data System (ADS)

Nabhan, Abdullah I.; Yang, Wan

2018-04-01

The facies and environments along the arid siliciclastic coast of Red Sea in Al Qahmah, Saudi Arabia are studied to establish a depositional model for interpretation of ancient rocks deposited in rift settings. Field and petrographic studies of 151 sediment samples in an area of 20 km2 define seven main facies types: beach, washover fan, tidal channel, dune, sabkha, delta, and wadi (seasonal stream). The wadi and delta facies are composed of poorly to moderately well-sorted, gravelly, medium-to-fine sands. Delta-front sands are redistributed by southward longshore currents to form a beach. Beach facies is composed of well-to-moderately sorted fine sands with minor gravels, which contain high concentrations of magnetite, ilmenite, garnet, pyroxene, amphibole, epidote, titanite, and apatite grains, indicating strong winnowing. Crabs and other burrowers destroy primary sedimentary structures and mix sediments in foreshore and backshore of the beaches. Wind and storm surge rework foreshore and backshore sediments to form washover fans. Sabkha facies occurs extensively in supratidal depressions behind beach, are flooded by rainstorms and spring tide, and capped by a 5-cm-thick crust composed of interlaminated halite, quartz, albite, minor gypsum and biotite, and rarely calcium carbonate. Halite occurs as thin sheets and gypsum as nodules with a chicken-wire structure. Clastic fraction in sabkha sediments ranges from coarse silt to coarse sand with moderate sorting, and is transported by currents and wind. Tidal inlets and tidal creeks assume abandoned wadis and are filled by muddy sand. Sand dunes and sand sheets are 1-7 m high and widely distributed due to variable wind directions. Fine-grained dune sands are moderately well sorted, whereas sheet sands are coarser and poorly sorted due to vegetation baffling. Most eolian sands are sourced from beach deposits. This suite of complex riverine, wave, tidal, wind, chemical, and biological processes form the facies mosaic along the arid Al Qahmah coast, which is strongly affected by climate-driven evaporation and wind action.

Control technology for crystalline silica exposures in construction: wet abrasive blasting.

PubMed

Golla, Vijay; Heitbrink, William

2004-03-01

This study was designed to document the effect that wet abrasive blasting has on reducing worker exposure to crystalline silica, which has been associated with silicosis and premature death. In this study, worker exposure to respirable crystalline silica was monitored during wet abrasive blasting on the exterior walls of a parking garage to remove surface concrete and expose the underlying aggregate. In this process a wet sand mix comprised of 80% dry sand and 20% water was used. Sampling and analysis revealed that the geometric mean respirable quartz concentration was 0.2 mg/m(3) for workers conducting abrasive blasting and 0.06 mg/m(3) for helpers. When abrasive blasting was conducted in areas that apparently had reduced natural ventilation, dust exposures appeared to increase. When compared with other published data, this case study suggests that wet abrasive blasting causes less exposure to crystalline silica than dry abrasive blasting.

'Micro-hole' optical dating of quartz from HOTRAX-05 Arctic Ocean cores

NASA Astrophysics Data System (ADS)

Berger, G. W.; Polyak, L. V.

2011-12-01

For Quaternary Arctic Ocean cores, numeric dating methods are needed spanning and exceeding the age range of the widely used radiocarbon (C-14) method. Previously, luminescence sediment dating of 4-11 μm diameter quartz and feldspar grains from core tops has often produced large burial-age overestimates (e.g., by >7 kyr) due to failure to resolve mixed-age histories. However, application of micro-focused-laser ('micro-hole') photon-stimulated-luminescence (PSL) applied to quartz grains of 11-90 μm diameters from the tops (upper 2 cm) of high-sedimentation- rate HOTRAX-05 multi-cores at the Alaska margin provides expected near zero ages (0-200 a), thus overcoming the earlier problem of large PSL age over-estimation. This micro-hole PSL dating approach has also been applied to >11 μm quartz grains from multi-cores at two sites on the central Lomonosov Ridge. For a core top within a perched basin, a burial-age estimate of ~2 ka for 11-62 μm quartz was obtained, in accord with published C-14 age estimates from foraminifera, demonstrating the efficacy of the micro-hole approach to this ridge area. At a nearby 'erosive' ridge-top site, the micro-hole PSL approach paradoxically produces two different burial-age estimates from the same core-top horizon. The >90 μm quartz grains yield a burial age of ~25 ka, in accord with a C-14 age estimate of ~26 ka from >250 μm foraminifers from the same horizon. However, the 11-90 μm quartz produces a burial-age estimate of ~9 ka, indicating a differently preserved burial history for the medium silt grains than for the sand grains within a single horizon. This unexpected result provides a unique insight into past, complicated, depositional processes on this ridge top over a time range spanning the LGM. These results from the micro-hole PSL approach thus indicate a clear potential for dating times of detrital quartz deposition at other ridge tops in the Arctic Ocean, and for providing perhaps new insights into local preservation of burial ages. These PSL procedures are being applied also to sediment above and below a diamicton in a HOTRAX-05 core from the Northwind Ridge, with the aim of dating indirectly the diamicton. Preliminary results from this core will be presented.

Ultrapure glass optical waveguide development in microgravity by the sol-gel process

NASA Technical Reports Server (NTRS)

Mukherjee, S. P.

1980-01-01

The alkali-borosilicate system was selected as the glass system for the preparation of ultrapure low loss glasses suitable for optical communication. The effect of different oxide contents on the absorption loss was critically reviewed. One composition was chosen to develop the gel preparation procedure in the alkali-borosilicate system. In addition, several procedures for the preparation of gels based on two different approaches were developed. The influence of different preparation parameters were investigated qualitatively. Several conclusions are drawn from the results.

Quantitative comparisons of analogue models of brittle wedge dynamics

NASA Astrophysics Data System (ADS)

Schreurs, Guido

2010-05-01

Analogue model experiments are widely used to gain insights into the evolution of geological structures. In this study, we present a direct comparison of experimental results of 14 analogue modelling laboratories using prescribed set-ups. A quantitative analysis of the results will document the variability among models and will allow an appraisal of reproducibility and limits of interpretation. This has direct implications for comparisons between structures in analogue models and natural field examples. All laboratories used the same frictional analogue materials (quartz and corundum sand) and prescribed model-building techniques (sieving and levelling). Although each laboratory used its own experimental apparatus, the same type of self-adhesive foil was used to cover the base and all the walls of the experimental apparatus in order to guarantee identical boundary conditions (i.e. identical shear stresses at the base and walls). Three experimental set-ups using only brittle frictional materials were examined. In each of the three set-ups the model was shortened by a vertical wall, which moved with respect to the fixed base and the three remaining sidewalls. The minimum width of the model (dimension parallel to mobile wall) was also prescribed. In the first experimental set-up, a quartz sand wedge with a surface slope of ˜20° was pushed by a mobile wall. All models conformed to the critical taper theory, maintained a stable surface slope and did not show internal deformation. In the next two experimental set-ups, a horizontal sand pack consisting of alternating quartz sand and corundum sand layers was shortened from one side by the mobile wall. In one of the set-ups a thin rigid sheet covered part of the model base and was attached to the mobile wall (i.e. a basal velocity discontinuity distant from the mobile wall). In the other set-up a basal rigid sheet was absent and the basal velocity discontinuity was located at the mobile wall. In both types of experiments, models accommodated initial shortening by a forward- and a backward-verging thrust. Further shortening was taken up by in-sequence formation of forward-verging thrusts. In all experiments, boundary stresses created significant drag of structures along the sidewalls. We therefore compared the surface slope and the location, dip angle and spacing of thrusts in sections through the central part of the model. All models show very similar cross-sectional evolutions demonstrating reproducibility of first-order experimental observations. Nevertheless, there are significant along-strike variations of structures in map view highlighting the limits of interpretations of analogue model results. These variations may be related to the human factor, differences in model width and/or differences in laboratory temperature and especially humidity affecting the mechanical properties of the granular materials. GeoMod2008 Analogue Team: Susanne Buiter, Caroline Burberry, Jean-Paul Callot, Cristian Cavozzi, Mariano Cerca, Ernesto Cristallini, Alexander Cruden, Jian-Hong Chen, Leonardo Cruz, Jean-Marc Daniel, Victor H. Garcia, Caroline Gomes, Céline Grall, Cecilia Guzmán, Triyani Nur Hidayah, George Hilley, Chia-Yu Lu, Matthias Klinkmüller, Hemin Koyi, Jenny Macauley, Bertrand Maillot, Catherine Meriaux, Faramarz Nilfouroushan, Chang-Chih Pan, Daniel Pillot, Rodrigo Portillo, Matthias Rosenau, Wouter P. Schellart, Roy Schlische, Andy Take, Bruno Vendeville, Matteo Vettori, M. Vergnaud, Shih-Hsien Wang, Martha Withjack, Daniel Yagupsky, Yasuhiro Yamada

The White Nile sedimentary system

NASA Astrophysics Data System (ADS)

Garzanti, Eduardo; Andò, Sergio; Padoan, Marta; Resentini, Alberto; Vezzoli, Giovanni; Villa, Igor

2014-05-01

The Nile River flows for ~6700 km from south of the Equator to finally reach the Mediterranean Sea at northern subtropical latitudes (Woodward et al. 2007). This is the longest sedimentological laboratory on Earth, a unique setting in which we are investigating changes in sediment composition associated with diverse chemical and physical processes, including weathering and hydraulic sorting. The present study focuses on the southern branch of the Nile across 20° of latitude, from hyperhumid Burundi and Rwanda highlands in central Africa to Khartoum, the capital city of Sudan at the southern edge of the Sahara. Our study of the Kagera basin emphasizes the importance of weathering in soils at the source rather than during stepwise transport, and shows that the transformation of parent rocks into quartzose sand may be completed in one sedimentary cycle (Garzanti et al. 2013a). Micas and heavy minerals, less effectively diluted by recycling than main framework components, offer the best key to identify the original source-rock imprint. The different behaviour of chemical indices such as the CIA (a truer indicator of weathering) and the WIP (markedly affected by quartz dilution) helps us to distinguish strongly weathered first-cycle versus polycyclic quartz sands (Garzanti et al. 2013b). Because sediment is efficiently trapped in East African Rift lakes, the composition of Nile sediments changes repeatedly northwards across Uganda. Downstream of both Lake Kyoga and Lake Albert, quartzose sands are progressively enriched in metamorphiclastic detritus supplied from tributaries draining amphibolite-facies basements. The evolution of White Nile sediments across South Sudan, a scarcely accessible region that suffered decades of civil war, was inferred from the available information (Shukri 1950), integrated by original petrographic, heavy-mineral and geochemical data (Padoan et al. 2011). Mineralogical and isotopic signatures of Bahr-el-Jebel and Sobat sediments, derived respectively from Archean gneisses of Uganda and Neoproterozoic basements of Ethiopia, become gradually homogenized and enriched in quartz, and remain finally unchanged down to Khartoum. This suggests massive sediment dumping in the Sudd and Machar Marshes, and explains why White Nile sediment contribution to the main Nile is negligible (Garzanti et al. 2006). REFERENCES Garzanti E., Andò S., Vezzoli G., Megid A.A.A., El Kammar A., 2006. Petrology of Nile River sands (Ethiopian and Sudan): sediment budgets and erosion patterns. EPSL 252:327-341. Garzanti E., Padoan M., Setti M., Peruta L., Najman Y., Villa I.M., 2013. Weathering geochemistry and Sr-Nd fingerprints of equatorial upper Nile and Congo muds. Geochem. Geophys. Geosyst. 14:292-316. Garzanti E., Padoan M., Andò S., Resentini A., Vezzoli G., Lustrino M., 2013. Weathering and relative durability of detrital minerals in equatorial climate: sand petrology and geochemistry in the East African Rift. J.Geol. 121:547-580. Padoan M., Garzanti E., Harlavan Y., Villa I.M., 2011. Tracing Nile sediment sources by Sr and Nd isotope signatures (Uganda, Ethiopia, Sudan). Geochim. Cosmochim. Acta 75:3627-3644. Shukri N.M., 1950. The mineralogy of some Nile sediments. Quart. J. Geol. Soc. London 105:511-534. Woodward J.C., Macklin M.G., Krom M.D., Williams M.A.J. 2007. The Nile: Evolution, quaternary river environments and material fluxes. In: Large Rivers, Avijit Gupta (Ed.), Wiley, 261-292.

Identification of Radar Facies and Linked Process-Based Palaeo-environmental Interpretations, Cooloola Sand Mass, Queensland, Australia

NASA Astrophysics Data System (ADS)

Gontz, A. M.; McCallum, A. B.; Moss, P. T.; Shulmeister, J.

2015-12-01

During 2015 and 2014, nearly 60 km of high-resolution ground penetrating radar data were acquired on the Cooloola Sand Mass (CSM) in southeastern coastal Queensland. The CSM is part of the world's largest downdrift sand system. It contains three of the world's largest sand islands, several National Parks, a UNESCO World Heritage Site and covers 500 km of the eastern Australian coastline in northern New South Wales and southern Queensland. The large (>200 m) composite dunes of the CSM exhibit multiple activation phases, coastally eroding bluffs and dune development is not obvious from surficial exposures. This provides an ideal environment for ground penetrating radar. The dune sequences have been provisionally dated to the mid Quaternary through present and represent the potential for a large palaeo-environmental proxy dataset. GPR imagery was collected using a MALA GeoSciences Ground Explorer (GX) system with 160 and 450 MHz antennae from the numerous physiographic and ecological provinces as well as mapped surficial soil units at the CSM. These data were used to determine the subsurface architecture, identify radar facies and develop environmental interpretations. In the clean, aeolian quartz-rich sands, radar wave penetration exceeded 30 m (radar velocity = 0.07 m/ns) with the 160 MHz antenna. From the interpreted environmental units including palaeosol, dune slip face, dune stoss face, sand blow, beach, estuarine and fluvial, we are developing maps to relate the units and focus a detailed sampling regime that includes OSL, sediment geochemistry and sedimentology, The interpreted units, stratigraphic correlation and spatial distribution of the facies is the first step in a broader project to unravel the Quaternary environmental and climate records that are archived within the sediments of the CSM.

Direct Measurement of Interparticle Forces of Titan Aerosol Analogs ("Tholin") Using Atomic Force Microscopy

NASA Astrophysics Data System (ADS)

Yu, Xinting; Hörst, Sarah M.; He, Chao; McGuiggan, Patricia; Bridges, Nathan T.

2017-12-01

To understand the origin of the dunes on Titan, it is important to investigate the material properties of Titan's organic sand particles on Titan. The organic sand may behave distinctively compared to the quartz/basaltic sand on terrestrial planets (Earth, Venus, and Mars) due to differences in interparticle forces. We measured the surface energy (through contact angle measurements) and elastic modulus (through Atomic Force Microscopy) of the Titan aerosol analog (tholin). We find that the surface energy of a tholin thin film is about 70.9 mN/m, and its elastic modulus is about 3.0 GPa (similar to hard polymers like PMMA and polystyrene). For two 20 μm diameter particles, the theoretical cohesion force is therefore 3.3 μN. We directly measured interparticle forces for relevant materials: tholin particles are 0.8 ± 0.6 μN, while the interparticle cohesion between walnut shell particles (a typical model materials for the Titan Wind Tunnel, TWT) is only 0.4 ± 0.1 μN. The interparticle cohesion forces are much larger for tholins and presumably Titan sand particles than materials used in the TWT. This suggests that we should increase the interparticle force in both analog experiments (TWT) and threshold models to correctly translate the results to real Titan conditions. The strong cohesion of tholins may also inform us how the small aerosol particles (˜1 μm) in Titan's atmosphere are transformed into large sand particles (˜200 μm). It may also support the cohesive sand formation mechanism suggested by Rubin and Hesp (2009), where only unidirectional wind is needed to form linear dunes on Titan.

Effects of clay minerals on transport of graphene oxide in saturated porous media.

PubMed

Lu, Taotao; Xia, Tianjiao; Qi, Yu; Zhang, Chengdong; Chen, Wei

2017-03-01

The presence of kaolinite, montmorillonite, and illite in packed quartz sand inhibited the transport of graphene oxide to different degrees. Transport inhibition was exerted mainly by the presence of positively charged sites on clay edges (which served as favorable deposition sites), whereas the effects on the overall particle-collector interaction energy and flow path were small. Kaolinite exhibited the most significant transport-inhibition effects because of its high percentage of edge area. Environ Toxicol Chem 2017;36:655-660. © 2016 SETAC. © 2016 SETAC.

Stability of nTiO2 particles and their attachment to sand: Effects of humic acid at different pH.

PubMed

Wu, Yang; Cheng, Tao

2016-01-15

The fate and transport of nano-scale or micro-scale titanium dioxide particles (nTiO2) in subsurface environments are strongly influenced by the stability of nTiO2 and their attachment to sediment grains. nTiO2 may carry either positive or negative charges in natural water, therefore, environmental factors such as pH, humic substances, and Fe oxyhydroxide coatings on sediment grains, which are known to control the stability and transport of negatively-charged colloids, may influence nTiO2 in different manners. The objective of this study is to investigate the effects of pH and humic acid (HA) on the stability and attachment of nTiO2 to sand at HA concentrations that are relevant to typical groundwater conditions, so that mechanisms that control nTiO2 immobilization and transport in natural systems can be elucidated. Stability and attachment of nTiO2 to quartz sand and Fe oxyhydroxide coated quartz sand are experimentally measured under a range of HA concentrations at pH5 and 9. Results show that at pH5, negatively-charged HA strongly adsorbs to positively-charged nTiO2 and Fe oxyhydroxide, which, at low HA concentrations, partially neutralizes the positive charges on nTiO2 and Fe oxyhydroxide, and therefore decreases the repulsive electrostatic forces between the surfaces, resulting in nTiO2 aggregation and attachment. At high HA concentrations, adsorbed HA reverses the surface charges of nTiO2 and Fe oxyhydroxide, and makes nTiO2 and Fe oxyhydroxide strongly negatively charged, resulting in stable nTiO2 suspension and low nTiO2 attachment. At pH9, HA, nTiO2, and Fe oxyhydroxide are all negatively charged, and HA adsorption is low and does not have a strong impact on the stability and attachment of nTiO2. Overall, this study shows that changes in surface charges of nTiO2 and Fe oxyhydroxide coating caused by HA adsorption is a key factor that influences the stability and attachment of nTiO2. Copyright © 2015 Elsevier B.V. All rights reserved.

Comparing geophysical measurements to theoretical estimates for soil mixtures at low pressures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wildenschild, D; Berge, P A; Berryman, K G

1999-01-15

The authors obtained good estimates of measured velocities of sand-peat samples at low pressures by using a theoretical method, the self-consistent theory of Berryman (1980), using sand and porous peat to represent the microstructure of the mixture. They were unable to obtain useful estimates with several other theoretical approaches, because the properties of the quartz, air and peat components of the samples vary over several orders of magnitude. Methods that are useful for consolidated rock cannot be applied directly to unconsolidated materials. Instead, careful consideration of microstructure is necessary to adapt the methods successfully. Future work includes comparison of themore » measured velocity values to additional theoretical estimates, investigation of Vp/Vs ratios and wave amplitudes, as well as modeling of dry and saturated sand-clay mixtures (e.g., Bonner et al., 1997, 1998). The results suggest that field data can be interpreted by comparing laboratory measurements of soil velocities to theoretical estimates of velocities in order to establish a systematic method for predicting velocities for a full range of sand-organic material mixtures at various pressures. Once the theoretical relationship is obtained, it can be used to estimate the soil composition at various depths from field measurements of seismic velocities. Additional refining of the method for relating velocities to soil characteristics is useful for development inversion algorithms.« less

Nivelstein sandstone, weakly lithified pure silica sands from the Dutch-German border area, intermittently used in architecture for two millennia

NASA Astrophysics Data System (ADS)

Nijland, Timo G.; Wim Dubelaar, C.

2017-04-01

The current paper provides a concise overview of the geological setting of the Nivelstein sandstone in broad sense, its petrographic and physical characteristics, and its use as natural stone. Miocene pure silica sands occur around Heerlen in the southeastern part of the Dutch province of Limburg and Herzogenrath in adjacent Germany, as well as in the Belgian province of Limburg near Opgrimbie. In Dutch Limburg and in Germany are three large active exploitations, quarrying the sands for industrial purposes. On top of the unconsolidated sands in the Herzogenrath quarry, lithified banks of sandstone occur, known as Nivelstein (or more rarely Herzogenrath) sandstone. This sandstone has been used as dimension stone and ornamental stone since Roman times. In the 11th century the quarry was reopened and after a long period of disuse sandstone blocks were again quarried in the second half of the 19th century. The lithification of the Nivelstein sandstone usually is very weak, with grain to grain contacts and some newly formed quartz rims only. The clay content is extremely low and is restricted to tiny booklets of kaolinite. Despite the weak cementation the Nivelstein sandstone has proved to be very time-resistant building stone that forms a major element in the stone cultural heritage of the Dutch- German border area.

Sand and clay mineralogy of sal forest soils of the Doon Siwalik Himalayas

NASA Astrophysics Data System (ADS)

Mukesh; Manhas, R. K.; Tripathi, A. K.; Raina, A. K.; Gupta, M. K.; Kamboj, S. K.

2011-02-01

The peteromineralogical characterization of the soil was carried out for the 12 soil profiles exposed in the Shorea robusta dominated forests of the Siwalik forest division, Dehradun. The quartz was observed as the dominating light mineral fraction (64-80%) in all the profiles studied. Biotite, hornblende, zircon, tourmaline, rutile and opaques comprising of iron minerals constituted the heavy mineral fraction (20%). The mineralogy of both the sand and clay fractions revealed a mixed mineralogy. The clay minerals in the order of their dominance were vermiculite, illite, kaolinite and mixed layer minerals. The presence of vermiculite and illite in appreciable quantities indicates that these were synthesized from the K-rich soil solution, as orthoclase and micas were present in significant quantities in the sand minerals. The mineral suites identified in the study shows that the geological, climatological and topographical factors of the region collectively played a dominant role in their formation and transformation. After critical appraisal of the results, it may be deduced that the mineralogical composition, physicochemical properties and total elemental analysis of the soils do not show any deficiency of the bases and other plant nutrients in general. The inherent fertility of the soil is good as indicated by the sand and clay mineralogy of the soil and the biotite and feldspar together with the mica is an important source of nutrients for the vegetation in the soils of the Doon valley.

Concurrent agglomeration and straining govern the transport of 14C-labeled few-layer graphene in saturated porous media.

PubMed

Su, Yu; Gao, Bin; Mao, Liang

2017-05-15

Deposition of graphene on environmental surfaces will dictate its transport and risks. In this work, the deposition, mobilization, and transport of 14 C-labeled few-layer graphene (FLG) in saturated quartz sand were systematically examined. Increasing solution ionic strength (IS) (1-100 mmol/L NaCl) resulted in greater retention of FLG (33-89%) in the sand and more hyper-exponential distribution of FLG along the sand column. Only a small fraction (≤7.4%) of the retained FLG was remobilized due to perturbation of IS by deionized water. These results indicate that trapping in pore spaces (i.e., physical straining) plays a dominant role in FLG deposition rather than attachment onto the surfaces of the sand. When IS, FLG input concentration, and flow velocity favor particle-particle interaction over particle-collector interaction, concurrent agglomeration within the pores promotes straining. In addition, electrostatic and steric repulsion that derived from the adsorbed organic macromolecules on FLG effectively reduced agglomeration and thereby enhanced transport and release of FLG. Moreover, the recovery of FLG (that deposited at 100 mmol/L NaCl) in the effluent reached 33% after speeding up the deionized water flushing rate. These findings highlight the need for FLG management in view of variations in transport behavior when assessing water quality and associated risks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Separability studies of construction and demolition waste recycled sand.

PubMed

Ulsen, Carina; Kahn, Henrique; Hawlitschek, Gustav; Masini, Eldon A; Angulo, Sérgio C

2013-03-01

The quality of recycled aggregates from construction and demolition waste (CDW) is strictly related to the content of porous and low strength phases, and specifically to the patches of cement that remain attached to the surface of natural aggregates. This phase increases water absorption and compromises the consistency and strength of concrete made from recycled aggregates. Mineral processing has been applied to CDW recycling to remove the patches of adhered cement paste on coarse recycled aggregates. The recycled fine fraction is usually disregarded due to its high content of porous phases despite representing around 50% of the total waste. This paper focus on laboratory mineral separability studies for removing particles with a high content of cement paste from natural fine aggregate particles (quartz/feldspars). The procedure achieved processing of CDW by tertiary impact crushing to produce sand, followed by sieving and density and magnetic separability studies. The attained results confirmed that both methods were effective in reducing cement paste content and producing significant mass recovery (80% for density concentration and 60% for magnetic separation). The production of recycled sand contributes to the sustainability of the construction environment by reducing both the consumption of raw materials and disposal of CDW, particularly in large Brazilian centers with a low quantity of sand and increasing costs of this material due to long transportation distances. Copyright © 2012 Elsevier Ltd. All rights reserved.

Transformation kinetics of corn and clover residues in mineral substrates of different composition

NASA Astrophysics Data System (ADS)

Pinskii, D. L.; Maltseva, A. N.; Zolotareva, B. N.; Dmitrieva, E. D.

2017-06-01

Mineralization kinetics of corn and clover residues in quartz sand, loam, sand + 15% bentonite, and sand + 30% kaolinite have been studied. A scheme has been proposed for the transformation of plant residues in mineral substrates. Kinetic parameters of mineralization have been calculated with the use of a first-order two-term exponential polynomial. It has been shown that the share of labile organic carbon pool in the clover biomass is higher (57-63%) than in the corn biomass (47-49%), which is related to the biochemical composition of plant residues. The mineralization constants of clover residues generally significantly exceed those of corn because of the stronger stabilization of the decomposition products of corn residues. The turnover time of the labile clover pool (4-9 days) in all substrates and that of the labile corn pool (8-10 days) in sands and substrates containing kaolinites and bentonite are typical for organic acids, amino acids, and simple sugars. In the loamy substrate, the turnover time of labile corn pool is about 46 days due to the stronger stabilization of components of the labile pool containing large amounts of organic acids. The turnover time of the stable clover pool (0.95 years) is significantly lower than that of the stable corn pool (1.60 years) and largely corresponds to the turnover time of plant biomass.

Transport of Cryptosporidium oocysts in porous media: Role of straining and physicochemical filtration

USGS Publications Warehouse

Tufenkji, N.; Miller, G.F.; Ryan, J.N.; Harvey, R.W.; Elimelech, M.

2004-01-01

The transport and filtration behavior of Cryptosporidium parvum oocysts in columns packed with quartz sand was systematically examined under repulsive electrostatic conditions. An increase in solution ionic strength resulted in greater oocyst deposition rates despite theoretical predictions of a significant electrostatic energy barrier to deposition. Relatively high deposition rates obtained with both oocysts and polystyrene latex particles of comparable size at low ionic strength (1 mM) suggest that a physical mechanism may play a key role in oocyst removal. Supporting experiments conducted with latex particles of varying sizes, under very low ionic strength conditions where physicochemical filtration is negligible, clearly indicated that physical straining is an important capture mechanism. The results of this study indicate that irregularity of sand grain shape (verified by SEM imaging) contributes considerably to the straining potential of the porous medium. Hence, both straining and physicochemical filtration are expected to control the removal of C. parvum oocysts in settings typical of riverbank filtration, soil infiltration, and slow sand filtration. Because classic colloid filtration theory does not account for removal by straining, these observations have important implications with respect to predictions of oocyst transport.

Modern sands of South America: composition, provenance and global significance

NASA Astrophysics Data System (ADS)

Potter, P. E.

1994-03-01

Standard petrographic methods were used to study 604 modern sands from South America, of which 351 came from rivers and 253 from beaches. In spite of the wide geomorphic contrasts, these sands belong to only three great families: (1) an immature Andean family of lithic arenites rich in volcanic and metamorphic grains that covers about 30% of South America; (2) a cratonic association rich in quartz that covers about 62% of the continent; and (3) a transitional, molasse association, which occurs between these two and covers only about 8% of the continent. The grand arithmetic average Q:F: Rf ratio for the entire continent is 60:11:29 and the area-weighted, carbonate-free average Qa:Fa:Rfa is 68:10:22, a superior continental estimate, and the first ever for an entire continent. Rock fragments are the most informative of all the provenance indicators and in South America they range from tropical alterites of the cratonic family through the dominant volcanic and metamorphic grains of the Andean family to biogenic carbonate in beach sands. Carbonate grains are almost totally absent in modern South American rivers because of present day tropical weathering and a long geological evolution that has favored sand production. They are present in many of the beach sands, however, and are most abundant along the tropical Brazilian and Caribbean coasts. Metamorphic grains rival volcanics as earmarks of the Andean family and survive tropical weathering far better than volcanic grains. There is a strong association between continental soil types and the composition of river sand, but the ultimate controls are tectonic history — the ancient landscapes preserved on the Gondwana shields of South America versus the tectonically young landscapes of the Andes — and climate. Climate can either cause ‘leaks’ to a far distant ocean where weathering is retarded by aridity or it can serve as a barrier to continental sand dispersion, where tropical weathering eliminates unstable grains in transit to the sea. When provenance studies are conducted across an entire, unglaciated continent, events in the far distant past need to be considered when seeking fundamental explanations of its contemporary, surficial sands.

Exceptional marine sand bodies in the Paleozoic of Oklahoma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fritz, R.D.; Kuykendall, M.D.; Hooker, E.O.

Of the wide variety of sandstone reservoirs in Oklahoma, the most unusual types of sand bodies are present in the Atokan Spiro Sandstone, Devonian Misener Sandstone, and Morrowan lower Morrow Sandstone. The common factors are that upon correlation and mapping these units are channel-like (fluvial-deltaic) in geometry, but from petrographic evidence are quartz-rich shallow-marine units, with the exclusion of intraclastic and diagenetic constituents. Stratigraphic mapping of the Spiro Sandstone of the Arkoma basin indicates two types of sand bodies: channel and sheet. The marine channel-like deposits, 10-150 ft thick, probably were deposited on a paleosurface produced by a pre-Atokan unconformity.more » Examination of cores and outcrop indicate that both the channel and sheet Spiro sands contain shallow-marine fossils, limestones, peloidal chamosite, burrows, and bioturbation, all indicative of a shallow-marine setting. The Misener Sandstone of north-central Oklahoma ranges from 10 to 100 ft thick with sharp boundaries. It was deposited in pre-Frisco/Woodford eroded paleochannels. Core evidence for shallow-marine deposition is glauconite, phosphatic fossils and clasts, burrows, and bioturbation. These were probably deposited in an embayed, estuary-like environment. The lower Morrow Sandstone of the Anadarko basin is similar in geometry, except that the sand bodies are multistoried and multilateral and do not appear to be associated with a regional unconformity. The lower Morrow sandstones, usually 30-60 ft thick. commonly are elongated and deposited parallel to the shoreline. Deposition is inferred to be shallow-marine from marine fossils and glauconite.« less

Microstructural and petrophysical characterization of a "structurally oversimplified" fault zone in poorly lithified sands: evidence for a coseismic rupture?

NASA Astrophysics Data System (ADS)

Balsamo, Fabrizio; Storti, Fabrizio

2010-05-01

We studied an extensional fault zone developed in poorly lithified, quartz-rich high porosity sandy sediments of the seismically active Crotone basin (southern Italy). The fault zone cuts across interlayered fine- to coarse-grained sands and consists of a cm-thick, discrete fault core embedded in virtually undeformed wall sediments. Consequently, it can be described as "structurally oversimplified" due to the lack of footwall and hanging wall damage zones. We acquired microstructural, grain size, grain shape, porosity, mineralogical and permeability data to investigate the influence of initial sedimentological characteristics of sands on the final faulted granular products and related hydrologic properties. Faulting evolves by a general grain size and porosity reduction with a combination of intragranular fracturing, spalling, and flaking of grain edges, irrespective of grain mineralogy. The dominance of cataclasis, also confirmed by fractal dimensions >2.6, is generally not expected at a deformation depth <1 km. Coarse-grained sand shows a much higher comminution intensity, grain shape variations and permeability drop than fine-grained sands. This is because coarser aggregates have (i) fewer grain-to-grain contacts for a given area, which results in higher stress concentration at contact points, and (ii) a higher probability of pre-existing intragranular microstructural defects that result in a lower grain strength. The peculiar structural architecture, the dominance of cataclasis over non-destructive particulate flow, and the compositional variations of clay minerals in the fault core, strongly suggest that the studied fault zone developed by a coseismic rupture.

Radon, radionuclides and the Cretaceous Folkestone Sands - gamma spectroscopy and geochemical analysis of silver sands and associated deposits in the SE of England.

NASA Astrophysics Data System (ADS)

Gillmore, Gavin; Al-Rafai, Yousef; Flowers, Alan

2017-04-01

Radon concentrations in a historic sand mine in Surrey, UK (Reigate Caves), have been measured by both real-time and time-averaged methods over a number of years. These mines are not identified as being in a 'Radon Affected Area' as defined by Public Health England, although concentrations show a summer level of 640 Bqm3 +-44 Bqm3. Average radon concentrations (September 2013 to January 2014) in Reigate caves were above the UK 200 Bqm3 domestic Action Level, above the UK domestic Target Level (of 100 Bqm3) but below the current workplace Action Level of 400 Bqm3. By way of a comparison radon has also been measured in nearby Dorking (South Street Caves). These enigmatic caves were not mined for sand for glass manufacture as Reigate Caves were and there is speculation on why the caves were created. Both are visited by tourists on a semi-regular basis. Dorking caves have a different morphology with radon concentrations in Autumn 2016 of up to 1940 +/- 230 Bqm3. The caves in Reigate are situated along Tunnel Road. These mines were also used as air raid shelters and wine stores. They consist of an East and West system and an older cave (Barons cave) which may have a medieval origin. As the Western Caves are now a shooting range our work has been carried out in the Eastern section at Reigate. Where Dorking is concerned the shops and houses in the town have extensive interconnected cellars and galleries cut into these sands. The caves probably date from the 17th century but were used quite extensively for wine storage in the 19th century due to their constant 140C air temperatures. Real-time measurements were taken with a Durridge Rad7 with time-averaged CR39 SSNTDs being placed throughout the cave systems to assess radon distribution and compare results with the real-time detector. Both caves contain marine shallow-water deposited locking (having tensile and compressive strength) silica sands of the Cretaceous Lower Greensand Group, Folkestone Formation, with little cement holding the grains together (typical porosity being around 30%). Microscope analysis shows that this material contains mostly angular to sub-angular quartz grains, some with undulose extinction under cross-polarised light. This suggests a metamorphic origin for the quartz. There are also some relatively rare rock fragments present. These silver sands are a mixture of fine to medium grain sizes (0.10 to 0.5 mm) with small proportions of finer and coarser grades and are in the order of 30 - 36 metres thick at Reigate. These beds show lateral and vertical variability in their grain size, mineralogy and geochemical make up such as iron oxide content and are heavily faulted in places. In view of these radon results, in order to determine whether these levels are supported or unsupported, samples were collected and subjected to laboratory-based Gamma spectrometry. This indicated the presence of U235 (186keV) and Pb212 (238keV) in sands from these caves. We will shortly be in a position to also report in-situ gamma spectrometry and ICPMS analysis of samples taken from these beds.

Inland aeolian deposits of the Iberian Peninsula: Sand dunes and clay dunes of the Duero Basin and the Manchega Plain. Palaeoclimatic considerations

NASA Astrophysics Data System (ADS)

Bernat Rebollal, M.; Pérez-González, A.

2008-12-01

This paper describes the latest research on the geomorphological characteristics, formation environment and chronology of the main inland aeolian deposits from the south-eastern Duero Basin (DB) and the Manchega Plain (MP) of the Iberian Peninsula. Similarities and differences between the aeolian deposits of these two locations are summarised. Wind deflation from the Guadiana and Júcar alluvial systems created the aeolian deposits of the MP. These deposits are mainly composed of quartz sands. However, in the San Juan alluvial plain (MP) there is a large extent of clay dunes formed by exposure to prevalent winds of seasonal playa-lakes with salt and clay sediments. In the DB, wind remobilisation of the small particles from Quaternary terraces and Tertiary arkosic sediments left aeolian deposits of quartz-feldspar sands. Textural parameters of the aeolian deposits show large variations depending on the location and the original deposit. Thus, in the DB the aeolian sands derived from the deflation of fluvial sediments are better sorted and smaller in grain size than those created by the deflation of arkosic sediments. Morphologically, simple and compound parabolic dunes (U-V forms, hemicyclic, lobate and elongate), crescentic and linear dunes, climbing dunes and blowout dunes have been recognized at both sites. Barchan and dome dunes are present only in the DB while "lunette lunette-clay dunes" are found only in the MP. In both locations, the large extent of aeolian sand sheets and the predominance of simple and compound parabolic dunes indicates the active role of sparse vegetation cover in the formation of this aeolian system. In the DB, dunes were formed by southwest and west winds, while in the MP the aeolian morphologies indicate that the prevalent winds were west and northwest. The chronology of the dune deposits is being determined with luminescence (TL-OSL) dating and Mass Spectrometry Analysis ( 14C-AMS). In this way, the aeolian activity and stabilisation stages can be established, the latter well marked in the DB through soil A horizon development. Thus, the main sand dune formation in the DB and the eastern regions of the MP occurred between 13.5 and 7 ka BP, during the cold and arid Younger Dryas episode and the Early Holocene. The clay dunes of the MP accumulated mainly from 29 to 19 ka BP that corresponds with Heinrich events HE-3 and HE-2 and the Last Glacial Maximum. However, clay dunes were also formed between 13.5 and 7 ka BP. In both locations, there have been reactivations of some sand deposits in the recent Holocene, with maximum activity around 5-2 ka BP and 0.5-0.2 ka BP. On the other hand, three marked stages of stabilisation of the DB aeolian system have been established with 14C-AMS, around 10.2, 6.2 and 1.2 ka BP. Finally, the main winds contributing to dune construction were also responsible for the deflation processes with the formation of erosional depressions.

Occupational exposures to respirable crystalline silica during hydraulic fracturing.

PubMed

Esswein, Eric J; Breitenstein, Michael; Snawder, John; Kiefer, Max; Sieber, W Karl

2013-01-01

This report describes a previously uncharacterized occupational health hazard: work crew exposures to respirable crystalline silica during hydraulic fracturing. Hydraulic fracturing involves high pressure injection of large volumes of water and sand, and smaller quantities of well treatment chemicals, into a gas or oil well to fracture shale or other rock formations, allowing more efficient recovery of hydrocarbons from a petroleum-bearing reservoir. Crystalline silica ("frac sand") is commonly used as a proppant to hold open cracks and fissures created by hydraulic pressure. Each stage of the process requires hundreds of thousands of pounds of quartz-containing sand; millions of pounds may be needed for all zones of a well. Mechanical handling of frac sand creates respirable crystalline silica dust, a potential exposure hazard for workers. Researchers at the National Institute for Occupational Safety and Health collected 111 personal breathing zone samples at 11 sites in five states to evaluate worker exposures to respirable crystalline silica during hydraulic fracturing. At each of the 11 sites, full-shift samples exceeded occupational health criteria (e.g., the Occupational Safety and Health Administration calculated permissible exposure limit, the NIOSH recommended exposure limit, or the ACGIH threshold limit value), in some cases, by 10 or more times the occupational health criteria. Based on these evaluations, an occupational health hazard was determined to exist for workplace exposures to crystalline silica. Seven points of dust generation were identified, including sand handling machinery and dust generated from the work site itself. Recommendations to control exposures include product substitution (when feasible), engineering controls or modifications to sand handling machinery, administrative controls, and use of personal protective equipment. To our knowledge, this represents the first systematic study of work crew exposures to crystalline silica during hydraulic fracturing. Companies that conduct hydraulic fracturing using silica sand should evaluate their operations to determine the potential for worker exposure to respirable crystalline silica and implement controls as necessary to protect workers.

Aggregation and transport of rutile titanium dioxide nanoparticles with montmorillonite and diatomite in the presence of phosphate in porous sand.

PubMed

Guo, Peng; Xu, Nan; Li, Duo; Huangfu, Xinxing; Li, Zuling

2018-08-01

Crop soil is inevitably contaminated by the excess of phosphate (P) fertilizers. A large amount of nanoparticle titanium dioxide (nTiO 2 ) entered soils as well due to the wide use of engineered nanomaterials. It is of great urgency and a high priority to investigate the mechanisms of nTiO 2 deposition with the presence of P in crop soils. This study investigated the transport behavior of (1.0 g L -1 ) rutile nTiO 2 with two representative clay particles (montmorillonite or diatomite) in the presence of P through the saturated quartz sand. In 10 mM NaCl electrolyte solution at pH 6.0, the recovery percentage of nTiO 2 was 36.3% from sand column. Nevertheless, it was reduced to 18.6% and 11.1% while montmorillonite and diatomite present in suspensions, respectively. Obviously, the improvement of nTiO 2 retention in sand was more pronounced by diatomite than montmorillonite. The likely mechanism for this result was that large aggregates were formed due to the attachment of nTiO 2 to montmorillonite and diatomite. Moreover, the surface of diatomite with the larger hydrodynamic radius was less negatively charged by comparison with montmorillonite. However, this phenomenon disappeared with the addition of P. P adsorption increases the repulsive force between particles and sand and the fast release of attached nTiO 2 -montmorillonite and diatomite from sand. The two-site kinetic retention model and the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory suggested that the combination of k 1/ k 1d , k 2 and secondary minimum energy can be used to accurately describe the attachment of nTiO 2 -montmorillonite and diatomite to sand in the presence of P. Copyright © 2018 Elsevier Ltd. All rights reserved.

Decontaminating Solar Wind Samples with the Genesis Ultra-Pure Water Megasonic Wafer Spin Cleaner

NASA Technical Reports Server (NTRS)

Calaway, Michael J.; Rodriquez, M. C.; Allton, J. H.; Stansbery, E. K.

2009-01-01

The Genesis sample return capsule, though broken during the landing impact, contained most of the shattered ultra-pure solar wind collectors comprised of silicon and other semiconductor wafers materials. Post-flight analysis revealed that all wafer fragments were littered with surface particle contamination from spacecraft debris as well as soil from the impact site. This particulate contamination interferes with some analyses of solar wind. In early 2005, the Genesis science team decided to investigate methods for removing the surface particle contamination prior to solar wind analysis.

Environmental Consequences of Nanotechnologies: Nanoparticle Dispersion in Aqueous Media: SOP-T-1

DTIC Science & Technology

2015-02-01

containing ice • Bath sonicator • Weighing dish (aluminum) • Stainless steel spatula • Analytical balance • Lab jack for lifting sample • Volumetric...balance and an aluminum dish, weigh an adequate mass of dry powder under a fume hood to achieve the desired concentration into ultrapure water (<T>, <R...0.025 0.5 0.05 1 0.5 10 1 20 2. Add ultra-pure water in a glass beaker with NP powder to /flask under fume hood (<T>, <R>). 3. Degas the bath

Real-time gamma imaging of technetium transport through natural and engineered porous materials for radioactive waste disposal.

PubMed

Corkhill, Claire L; Bridge, Jonathan W; Chen, Xiaohui C; Hillel, Phil; Thornton, Steve F; Romero-Gonzalez, Maria E; Banwart, Steven A; Hyatt, Neil C

2013-12-03

We present a novel methodology for determining the transport of technetium-99m, a γ-emitting metastable isomer of (99)Tc, through quartz sand and porous media relevant to the disposal of nuclear waste in a geological disposal facility (GDF). Quartz sand is utilized as a model medium, and the applicability of the methodology to determine radionuclide transport in engineered backfill cement is explored using the UK GDF candidate backfill cement, Nirex Reference Vault Backfill (NRVB), in a model system. Two-dimensional distributions in (99m)Tc activity were collected at millimeter-resolution using decay-corrected gamma camera images. Pulse-inputs of ~20 MBq (99m)Tc were introduced into short (<10 cm) water-saturated columns at a constant flow of 0.33 mL min(-1). Changes in calibrated mass distribution of (99m)Tc at 30 s intervals, over a period of several hours, were quantified by spatial moments analysis. Transport parameters were fitted to the experimental data using a one-dimensional convection-dispersion equation, yielding transport properties for this radionuclide in a model GDF environment. These data demonstrate that (99)Tc in the pertechnetate form (Tc(VII)O4(-)) does not sorb to cement backfill during transport under model conditions, resulting in closely conservative transport behavior. This methodology represents a quantitative development of radiotracer imaging and offers the opportunity to conveniently and rapidly characterize transport of gamma-emitting isotopes in opaque media, relevant to the geological disposal of nuclear waste and potentially to a wide variety of other subsurface environments.

Real-Time Gamma Imaging of Technetium Transport through Natural and Engineered Porous Materials for Radioactive Waste Disposal

PubMed Central

2013-01-01

We present a novel methodology for determining the transport of technetium-99m, a γ-emitting metastable isomer of 99Tc, through quartz sand and porous media relevant to the disposal of nuclear waste in a geological disposal facility (GDF). Quartz sand is utilized as a model medium, and the applicability of the methodology to determine radionuclide transport in engineered backfill cement is explored using the UK GDF candidate backfill cement, Nirex Reference Vault Backfill (NRVB), in a model system. Two-dimensional distributions in 99mTc activity were collected at millimeter-resolution using decay-corrected gamma camera images. Pulse-inputs of ∼20 MBq 99mTc were introduced into short (<10 cm) water-saturated columns at a constant flow of 0.33 mL min–1. Changes in calibrated mass distribution of 99mTc at 30 s intervals, over a period of several hours, were quantified by spatial moments analysis. Transport parameters were fitted to the experimental data using a one-dimensional convection–dispersion equation, yielding transport properties for this radionuclide in a model GDF environment. These data demonstrate that 99Tc in the pertechnetate form (Tc(VII)O4–) does not sorb to cement backfill during transport under model conditions, resulting in closely conservative transport behavior. This methodology represents a quantitative development of radiotracer imaging and offers the opportunity to conveniently and rapidly characterize transport of gamma-emitting isotopes in opaque media, relevant to the geological disposal of nuclear waste and potentially to a wide variety of other subsurface environments. PMID:24147650

Capillary pressure-saturation relations in quartz and carbonate sands: Limitations for correlating capillary and wettability influences on air, oil, and supercritical CO2 trapping

NASA Astrophysics Data System (ADS)

Wang, Shibo; Tokunaga, Tetsu K.; Wan, Jiamin; Dong, Wenming; Kim, Yongman

2016-08-01

Capillary pressure (Pc)-saturation (Sw) relations are essential for predicting equilibrium and flow of immiscible fluid pairs in soils and deeper geologic formations. In systems that are difficult to measure, behavior is often estimated based on capillary scaling of easily measured Pc-Sw relations (e.g., air-water, and oil-water), yet the reliability of such approximations needs to be examined. In this study, 17 sets of brine drainage and imbibition curves were measured with air-brine, decane-brine, and supercritical (sc) CO2-brine in homogeneous quartz and carbonate sands, using porous plate systems under ambient (0.1 MPa, 23°C) and reservoir (12.0 MPa, 45°C) conditions. Comparisons between these measurements showed significant differences in residual nonwetting phase saturation, Snw,r. Through applying capillary scaling, changes in interfacial properties were indicated, particularly wettability. With respect to the residual trapping of the nonwetting phases, Snwr, CO2 > Snwr, decane > Snwr, air. Decane-brine and scCO2-brine Pc-Sw curves deviated significantly from predictions assuming hydrophilic interactions. Moreover, neither the scaled capillary behavior nor Snw,r for scCO2-brine were well represented by decane-brine, apparently because of differences in wettability and viscosities, indicating limitations for using decane (and other organic liquids) as a surrogate fluid in studies intended to apply to geological carbon sequestration. Thus, challenges remain in applying scaling for predicting capillary trapping and multiphase displacement processes across such diverse fields as vadose zone hydrology, enhanced oil recovery, and geologic carbon sequestration.

Capillary pressure - saturation relations in quartz and carbonate sands: Limitations for correlating capillary and wettability influences on air, oil, and supercritical CO2 trapping

NASA Astrophysics Data System (ADS)

Tokunaga, T. K.; Wang, S.; Wan, J.; Dong, W.; Kim, Y.

2016-12-01

Capillary pressure (Pc) - saturation (Sw) relations are essential for predicting equilibrium and flow of immiscible fluid pairs in soils and deeper geologic formations. In systems that are difficult to measure, behavior is often estimated based on capillary scaling of easily measured Pc-Sw relations (e.g., air-water, and oil-water), yet the reliability of such approximations needs to be examined. In this study, seventeen sets of brine drainage and imbibition curves were measured with air-brine, decane-brine, and supercritical (sc) CO2-brine in homogeneous quartz and carbonate sands, using porous plate systems under ambient (0.1 MPa, 23 °C) and reservoir (12.0 MPa, 45 °C) conditions. Comparisons between these measurements showed significant differences in residual nonwetting phase saturation, Snw,r. Through applying capillary scaling, changes in interfacial properties were indicated, particularly wettability. With respect to the residual trapping of the nonwetting phases, Snwr, CO2 > Snwr, decane > Snwr, air. Decane-brine and scCO2-brine Pc-Sw curves deviated significantly from predictions assuming hydrophilic interactions. Moreover, neither the scaled capillary behavior nor Snw,r for scCO2-brine were well represented by decane-brine, apparently because of differences in wettability and viscosities, indicating limitations for using decane (and other organic liquids) as a surrogate fluid in studies intended to apply to geological carbon sequestration. Thus, challenges remain in applying scaling for predicting capillary trapping and multiphase displacement processes across such diverse fields as vadose zone hydrology, enhanced oil recovery, and geologic carbon sequestration.

Direct geoelectrical evidence of mass transfer at the laboratory scale

NASA Astrophysics Data System (ADS)

Swanson, Ryan D.; Singha, Kamini; Day-Lewis, Frederick D.; Binley, Andrew; Keating, Kristina; Haggerty, Roy

2012-10-01

Previous field-scale experimental data and numerical modeling suggest that the dual-domain mass transfer (DDMT) of electrolytic tracers has an observable geoelectrical signature. Here we present controlled laboratory experiments confirming the electrical signature of DDMT and demonstrate the use of time-lapse electrical measurements in conjunction with concentration measurements to estimate the parameters controlling DDMT, i.e., the mobile and immobile porosity and rate at which solute exchanges between mobile and immobile domains. We conducted column tracer tests on unconsolidated quartz sand and a material with a high secondary porosity: the zeolite clinoptilolite. During NaCl tracer tests we collected nearly colocated bulk direct-current electrical conductivity (σb) and fluid conductivity (σf) measurements. Our results for the zeolite show (1) extensive tailing and (2) a hysteretic relation between σf and σb, thus providing evidence of mass transfer not observed within the quartz sand. To identify best-fit parameters and evaluate parameter sensitivity, we performed over 2700 simulations of σf, varying the immobile and mobile domain and mass transfer rate. We emphasized the fit to late-time tailing by minimizing the Box-Cox power transformed root-mean square error between the observed and simulated σf. Low-field proton nuclear magnetic resonance (NMR) measurements provide an independent quantification of the volumes of the mobile and immobile domains. The best-fit parameters based on σf match the NMR measurements of the immobile and mobile domain porosities and provide the first direct electrical evidence for DDMT. Our results underscore the potential of using electrical measurements for DDMT parameter inference.

Depositional environment, sand provenance, and diagenesis of the Basal Salina Formation (lower Eocene), northwestern Peru

NASA Astrophysics Data System (ADS)

Marsaglia, K. M.; Carozzi, A. V.

The Basal Salina Formation is a lower Eocene transgressive sequence consisting of interbedded shales, siltstones, and conglomeratic sandstones. This formation occurs in the Talara basin of northwestern Peru and is one of a series of complexly faulted hydrocarbon-producing formations within this extensional forearc basin. These sediments were probably deposited in a fan-delta complex that developed along the ancestral Amotape Mountains during the early Eocene. Most of the sediment was derived from the low-grade metamorphic and plutonic rocks that comprise the Amotape Mountains, and their sedimentary cover. Detrital modes of these sandstones reflect the complex tectonic history of the area, rather than the overall forearc setting. Unlike most forearc sediments, these are highly quartzose, with only minor percentages of volcanic detritus. This sand is variably indurated and cemented by chlorite, quartz, calcite, and kaolinite. Clay-mineral matrix assemblages show gradational changes with depth, from primarily detrital kaolinite to diagenetic chlorite and mixed-layered illite/smectite. Basal Salina sandstones exhibit a paragenetic sequence that may be tied to early meteoric influx or late-stage influx of thermally driven brines associated with hydrocarbon migration. Much of the porosity is secondary, resulting from a first-stage dissolution of silicic constituents (volcanic lithic fragments, feldspar, and fibrous quartz) and a later dissolution of surrounding carbonate cement. Types of pores include skeletal grains, grain molds, elongate pores, and fracture porosity. Measured porosity values range up to 24% and coarser samples tend to be more porous. Permeability is enhanced by fractures and deterred by clay-mineral cements and alteration residues.

Major, trace and REE geochemistry of recent sediments from lower Catumbela River (Angola)

NASA Astrophysics Data System (ADS)

Vinha, Manuela; Silva, M. G.; Cabral Pinto, Marina M. S.; Carvalho, Paula Cristina S.

2016-03-01

The mineralogy, texture, major, trace and rare earth elements, from recent sediment samples collected in the lower Catumbela River, were analysed in this study to characterize and discuss the factors controlling its geochemistry and provide data that can be used as tracers of Catumbela River inputs to the Angolan continental shelf. The sediments are mainly sands and silty-sands, but sandy-silt also occurs and the mineralogy is composed of quartz, feldspar, phyllosilicates, magnetite, ilmenite and also carbonates when the river crosses limestones and marls in the downstream sector. The hydraulic sorting originates magnetite-ilmenite and REE-enriched minerals placers. The mineralogy of the sediments is controlled by the source rocks and the degree of chemical weathering is lower than erosion. The texture is mainly controlled by location. There is enrichment in all the analysed trace elements in the fine grained, clay minerals and Fe-oxy-hydroxides rich sediments, compared to the coarse grained and quartz plus feldspar rich ones. The coarse grained sediments (without the placers) are impoverished in ΣREE when compared with UCC and NASC compositions, while the fine grained sediments have ΣREE contents similar to UCC and NASC. The placers have ΣREE contents up to 959.59 mg/kg. The source composition is the dominant factor controlling the REE geochemistry of the analysed sediments as there is no difference in the (La/Yb)N, (La/Sm)N and (Gd/Yb)N ratios in coarse and fine grained sediments. The sorting of magnetite, ilmenite, zircon, throrite, thorianite, rutile and titanite explain the HREE/LREE enriched patterns of the coarse grained sediments.

Direct geoelectrical evidence of mass transfer at the laboratory scale

USGS Publications Warehouse

Swanson, Ryan D.; Singha, Kamini; Day-Lewis, Frederick D.; Binley, Andrew; Keating, Kristina; Haggerty, Roy

2012-01-01

Previous field-scale experimental data and numerical modeling suggest that the dual-domain mass transfer (DDMT) of electrolytic tracers has an observable geoelectrical signature. Here we present controlled laboratory experiments confirming the electrical signature of DDMT and demonstrate the use of time-lapse electrical measurements in conjunction with concentration measurements to estimate the parameters controlling DDMT, i.e., the mobile and immobile porosity and rate at which solute exchanges between mobile and immobile domains. We conducted column tracer tests on unconsolidated quartz sand and a material with a high secondary porosity: the zeolite clinoptilolite. During NaCl tracer tests we collected nearly colocated bulk direct-current electrical conductivity (σb) and fluid conductivity (σf) measurements. Our results for the zeolite show (1) extensive tailing and (2) a hysteretic relation between σf and σb, thus providing evidence of mass transfer not observed within the quartz sand. To identify best-fit parameters and evaluate parameter sensitivity, we performed over 2700 simulations of σf, varying the immobile and mobile domain and mass transfer rate. We emphasized the fit to late-time tailing by minimizing the Box-Cox power transformed root-mean square error between the observed and simulated σf. Low-field proton nuclear magnetic resonance (NMR) measurements provide an independent quantification of the volumes of the mobile and immobile domains. The best-fit parameters based on σf match the NMR measurements of the immobile and mobile domain porosities and provide the first direct electrical evidence for DDMT. Our results underscore the potential of using electrical measurements for DDMT parameter inference.

Comparison of four advanced oxidation processes for the removal of naphthenic acids from model oil sands process water.

PubMed

Liang, Xiaoming; Zhu, Xingdong; Butler, Elizabeth C

2011-06-15

Four advanced oxidation processes (UV/TiO(2), UV/IO(4)(-), UV/S(2)O(8)(2-), and UV/H(2)O(2)) were tested for their ability to mineralize naphthenic acids to inorganic carbon in a model oil sands process water containing high dissolved and suspended solids at pH values ranging from 8 to 12. A medium pressure mercury (Hg) lamp was used, and a Quartz immersion well surrounded the lamp. The treatment goal of 5mg/L naphthenic acids (3.4 mg/L total organic carbon (TOC)) was achieved under four conditions: UV/S(2)O(8)(2-) (20mM) at pH 8 and 10, and UV/H(2)O(2) (50mM) at pH 8 (all with the Quartz immersion well). Values of electrical energy required to meet the treatment goal were about equal for UV/S(2)O(8)(2-) (20mM) and UV/H(2)O(2) (50mM) at pH 8, but three to four times larger for treatment by UV/S(2)O(8)(2-) (20mM) at pH 10. The treatment goal was also achieved using UV/S(2)O(8)(2-) (20mM) at pH 10 when using a Vycor filter that transmits light primarily in the mid and near UV, suggesting that that treatment of naphthenic acids by UV/S(2)O(8)(2-) using low pressure Hg lamps may be feasible. Copyright © 2011 Elsevier B.V. All rights reserved.

First documentation of tidal-channel sponge biostromes (upper Pleistocene, southeastern Florida)

USGS Publications Warehouse

Cunningham, K.J.; Rigby, J.K.; Wacker, M.A.; Curran, H.A.

2007-01-01

Sponges are not a common principal component of Cenozoic reefs and are more typically dominant in deep-water and/or cold-water localities. Here we report the discovery of extensive upper Pleistocene shallow-marine, tropical sponge biostromes from the Mami Limestone of southeastern Florida built by a new ceractinomorph demosponge. These upright, barrel- to vase-shaped sponges occur in monospecific aggregations constructed within the tidal channels of an oolitic tidal-bar belt similar to modern examples on the Great Bahama Bank. The biostromes appear to have a ribbon-like geometry, with densely spaced sponges populating a paleochannel along a 3.5 km extent in the most lengthy biostrome. These are very large (as high as 2 m and 1.8 m in diameter), particularly well-preserved calcified sponges with walls as hard as concrete. Quartz grains are the most common particles agglutinated in the structure of the sponge walls. Where exposed, sediment fill between the sponges is commonly a highly burrowed or cross-bedded ooid-bearing grainstone and, locally, quartz sand. It is postulated that the dense, localized distribution of these particular sponges was due to a slight edge over competitors for food or energy supply and space in a stressed environment of tidal-influenced salinity and nutrient changes, strong currents, and frequently shifting submarine sand dunes. To our knowledge, this represents the first documentation of sponge biostromes composed of very large upright sponges within high-energy tidal channels between ooid shoals. The remarkably well-preserved accumulations provide an alternative example of sponge reefs for comparative paleoenvironmental studies. ?? 2007 The Geological Society of America.

Micro X-ray CT Imaging of Sediments under Confining Pressure

NASA Astrophysics Data System (ADS)

Schindler, M.; Prasad, M.

2016-12-01

We developed a pressure and temperature control system for use inside the micro X-ray CT scanner Xradia 400. We succeeded in building a pressure vessel that can be pressurized to 34.5 MPa (5000 psi) while being transparent to X-rays. The setup can currently be cooled to -5°C and heated to 40°C. We were able to observe grain damage and porosity reduction due to applied confining pressure in clean quartz sand samples and quartz sand and bentonite samples. By comparing micro CT images at atmospheric pressure and 13.8 MPa (2000 psi) confining pressure, we observed compaction of the samples resulting in grain damage and fracturing of sediment grains (Figure 1). When the confining pressure was decreased some grains experienced further fracturing. The grain damage appears irreversible. Further fracturing of grains in pre-compacted sediment was observed upon repeated confining pressure cycling. We are currently working on feed-throughs for fluid lines and electric wiring to use ultrasonic transducers and pressure control in combination. Further we plan to include pore pressure in addition to confining pressure into the system. The pressure control system in combination with ultrasonic transducers will allow us to visually observe pore scale changes in rock samples while simultaneously identifying their influence on ultrasonic velocities. Such pore-scale changes are usually not taken into account by rock physics models and could help to identify why laboratory data diverges from theoretical models. Further, it is possible to compute compressibility from mCT images at different stress states by image correlation

Analyzing the Deposition of Titanium Dioxide Nanoparticles at Model Rough Mineral Surfaces Using a Quartz Crystal Microbalance with Dissipation Monitoring

NASA Astrophysics Data System (ADS)

Li, Y.; Kananizadeh, N.; Rodenhausen, K. B.; Schubert, M.; Bartelt-Hunt, S.

2015-12-01

Titanium dioxide nanoparticles (nTiO2) is the most extensively manufactured engineered materials. nTiO2 from sunscreens was found to enter sediments after released into a lake. nTiO2 may also enter the subsurface via irrigation using effluents from wastewater treatment plants. Interaction of nTiO2 with soils and sediments will largely influence their fate, transport, and ecotoxicity. Measuring the interaction between nTiO2 and natural substrates (e.g. such as sands) is particularly challenging due to highly heterogeneous and rough natural sand surfaces. In this study, an engineered controllable rough surface known as three dimensional nanostructured sculptured columnar thin films (SCTFs) has been used to mimic surface roughness. SCTFs were fabricated by glancing angle deposition (GLAD), a physical vapor deposition technique facilitated by electron beam evaporation. Interaction between nTiO2 and SCTF coated surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). In parallel, a Generalized Ellipsometry (GE) was coupled with the QCM-D to measure the deposition of nTiO2. We found that the typical QCM-D modeling approach, e.g. viscoelastic model, would largely overestimate the mass of deposited nTiO2, because the frequency drops due to particle deposition or water entrapment in rough areas were not differentiated. Here, we demonstrate a new approach to model QCM-D data for nTiO2 deposition on rough surfaces, which couples the viscoelastic model with a model of flow on the non-uniform surface.

Petrological and geochemical compositions of beach sands of the Barton and Weaver peninsulas of King George Island, West Antarctica: implications for provenance and deglacial history

NASA Astrophysics Data System (ADS)

Lee, Y. I.; Lim, H. S.; Choi, T.

2017-12-01

We studied the provenance of beach sediments of the Baton and Weaver peninsulas of King George Island, the South Shetland Islands of West Antarctica. The studied beach sand sediments of the both peninsulas are predominantly composed of volcanic-rock fragment, followed by altered grain and plutonic rock fragment in that order. In rock fragments, the volcanic rock fragments are about four times more than the plutonic rock fragments. The median quartz-feldspar-rock fragment (Q-F-R) ratios of the beach sands of the Weaver and Barton peninsulas are Q3.4-F5.5-R99.1 and Q0.5-F2.7-R96.8, respectively. These beach sands may have been originated from basaltic andesite-andesite distributed in the ice-free areas of the Barton and Weaver peninsulas and granodiorite of the Barton Peninsula. According to the geochemistry of the beach sand sediments of the two peninsulas, most of the sand samples are interpreted as originating from intermediate rocks that have experienced little chemical weathering. Taking together the modal composition and geochemical composition of the beach sand samples, the tectonic setting of the source area is interpreted as a magmatic arc setting. This interpretation is consistent with geology of the ice-free areas of the Barton and Weaver peninsulas and the tectonic setting of King George Island. However, the sand samples of the Barton Peninsula southern beach and the Weaver Peninsula beach were not derived from basement rocks currently exposed in the ice-free areas of the corresponding peninsula, but were formerly glaciomarine sediments derived from erosion of ice-covered subglacial basement rocks and transported to the submerged glacier grounding line prior to deglaciation. Sand sediments derived from wave erosion of basement rocks of paleoshoreline might have been mixed with these glaciomarine sediments. King George Island became uplifted due to deglaciation 6,000 years ago. The studied beach sediments might have been reworked after the uplift of the King George Island to the present level. Accordingly, the studied beach sand sediments of the Barton and Weaver peninsulas are interpreted to be a palimpsest deposit comprising a mixture of originally glaciomarine sediments accumulated in the shallow fjord post the Last Glacial Maximum and some detritus supplied to the beaches since deglaciation.

Foundations of Forensic Meteoritics

NASA Astrophysics Data System (ADS)

Treiman, A. H.

1992-07-01

It may be useful to know if a meteorite was found at the site where it fell. For instance, the polymict ureilites North Haig and Nilpena were found 1100 km apart, yet are petrologically identical [1]. Could this distance represent transport from a single strewn field, or does it represent distinct fall sites? A meteorite may contain sufficient clues to suggest some characteristics of its fall site. If these inferences are inconsistent with the find site, one may infer that the meteorite has been transported. It will likely be impossible to determine the exact fall site of a transported meteorite. Data relevant to a meteorite's fall site may be intrinsic to the meteorite, or acquired at the site. For instance, an intrinsic property is terrestrial residence age (from abundances of cosmogenic radioisotopes and their decay products); a meteorite's terrestrial residence age must be the same or less than that of the surface on which it fell. After falling, a meteorite may acquire characteristic telltales of terrestrial geological, geochemical, and biological processes. These telltale clues may include products of chemical weathering, adhering geological materials, biological organisms living (or once living) on the meteorite, and biological materials adhering to (but never living on) the meteorite. The effects of chemical weathering, present in all but the freshest finds, range from slight rusting to extensive decomposition and veining The ages of weathering materials and veins, as with terrestrial residence ages above, must be less than the age of the fall surface. The mineralogy and chemistry, elemental and isotopic, of weathering materials will differ according to the mineralogy and composition of the meteorite, and the mineralogy, geochemistry, hydrology, and climate of the fall site. Weathering materials may also vary as climate changes and may vary among the microenvironments associated with a meteorite on the Earth's surface. Geological materials (rock, sediment, soil) adhering to a meteorite are samples of the actual physical environment in which the meteorite rested. Adhesion may derive from chemical cementation (incl. rust from the meteorite), biologic activity (incl. desert varnish?), or impact processes [2]. Given the wide diversity of geological materials and processes on the Earth, adhering geological materials may be useful forensic tools. For instance, fall in a volcanic terrane may be inconsistent with adhering sediments of clean quartz sand. Biologic matter on meteorites includes animal and vegetable matter mixed with the adhering geological materials, lichens and other plants growing in place, and purposefully attached animal matter (e.g. insect eggs). The most useful biological data may be provided by pollen, which can often be referred unambiguously to genera and species of plants. For example, sediments adhering to meteorites from the central Nullabor Plain (W. Australia) are different from sediments from the Plain's margin in S. Australia. Sediment on meteorites from the central Nullabor (e.g. Mundrabilla) lacks quartz sand and consists almost entirely of clay-sized particles, consistent with derivation from the local saprolitic soil. Sediment on meteorites from the eastern Nullabor (e.g. Hughes and Cook, S.A.) contains a significant fraction of quartz sand, 1/4- to 1/2-mm grains, probably blown from the Great Victoria Desert to the north and northwest. However, sedimentologic data alone may be misleading. For instance, sediments adhering to Nuevo Mercurio stones (H5; Zacatecas, Mexico) are clay-sized and lack coarser material. But sediment on Nuevo Mercurio (b), a ureilite found in the Nuevo Mercurio strewn field, consists of quartz sand and clay pellets, 1/4 to 1/2 mm diameter. Clearly, local environments may affect the character of sediment adhering to a meteorite, and careful detailed study may be required to determine whether a meteorite has been transported. I am grateful to R. Farrell and D. New for availability of samples. References: 1. Prinz et al. (1986) Lunar Planet. Sci. XVII, 681. [2] Koeberl and Schultz (1992) Lunar Planet. Sci. XXIII, 707.

The Enigmatic Longevity of Granular Materials on Mars: The Case for Geologically Episodic Dune Formation

NASA Technical Reports Server (NTRS)

Marshall, J.

1999-01-01

Martian sand dunes are concentrated in vast sand seas in the circumpolar belt of the planet's northern hemisphere, but they are also pervasive over the whole planet. Their occurrence is to be expected on a super-arid planetary surface subjected to boundary layer drag from a continually active atmosphere. Whilst their occurrence is to be expected, their survival is enigmatic. But the enigma only arises if the martian system is considered similar to Earth's --where sand is moved highly frequently, more or less on a seasonal basis. Experimentally it is readily demonstrated that active sand will soon wear down to small grains and eventually diminish to below the critical sand size required to sustain dune formation. According to conventional wisdom, sand moves at higher speeds on Mars than on Earth, and if it were to move as frequently as it does on Earth, then the dune-forming sand population should have long since disappeared, given the great longevity of the martian aeolian system (Sagan coined the term "kamikaze" grains to express this disappearance). No supply of sand could keep pace with this depletion, especially in light of the fact that Mars does not have very active weathering, nor significant crustal differentiation. On Earth, plate tectonics, magmatic activity, and general crustal differentiation over geological time have produced great concentrations of quartz crystals in the continental crustal masses. Not only are these quartz grains chemically and mechanically resilient, they are about the right size for being transported by either wind or water. Add to this, the geologically recent contribution of glacial grinding, and it is easy to see why there are dune field on Earth. So what are the martian dunes composed of, and how does the material survive the eons of attrition? In addition to experimental demonstrations of sand comminution in laboratory aeolian simulations, the problem can be approached from first principles. Sagan showed that by simple considerations of material strength versus mechanical work applied to the material, comminution to sub-sand size would be inevitable. Another semi-analytical approach might be taken by considering that the archetypal aeolian sand surface texture is an irregularly pitted ("frosted") surface composed of chipping hollows approximately 10 microns in diameter, 5 microns deep. Their volume = about 250 cubic microns, or about 1/25000 of the volume of a 100 micron diameter dune grain. Because a saltating grain always strikes another grain, then two surfaces are impacted. Thus each grain undergoes two impacts for every one saltation leap, when the impact statistics are considered for a closed dune system (it can be calculated that a grain can never undergo <1 impact, and never >2 per saltation leap). Hence, if we conservatively assume that there is damage to a grain each time it bounces, but with the minimum damage of only 2 microscopic craters per impact, then approximately 12,500 impacts are required to completely eliminate the grain. Of course, it would require only a fraction of this amount to reduce the grain to below sand size. A grain will make only several tens of saltation leaps on the stoss side of a dune before becoming buried on the lee slope. The dune then has to move its full length before the grain is exhumed again for abrasion. Even with this hiatus in transport, it is easy to see that terrestrial dunes need resupplying with sand in order to survive. In recent theoretical work it has been shown that martian aeolian transport may be initiated with high-speed grains, but this converts to a lower energy dynamic transport equilibrium in which a reptation population dominates grain transport (on Earth, at least half of the flux is by reptation and creep). On Mars, therefore, average grain speeds may be lower than those on Earth, or at least comparable. This would permit greater longevity for martian sands, but it would not go far enough to solve the survival problem. It may, however, explain why martian dunes are about the same size as terrestrial dunes. If martian saltation leaps were significantly longer than on Earth (as usually assumed), then a dune's lee slope would have to be correspondingly longer in order to trap the sand; this would scale up the whole dune structure. But with shorter trajectories in a reptation population, larger dunes would be unnecessary. Additional information is contained in the original.

The timing of sediment transport down Monterey Submarine Canyon, offshore California

USGS Publications Warehouse

Stevens, Thomas; Paull, Charles K.; Ussler, William III; McGann, Mary; Buylaert, Jan-Pieter; Lundsten, Eve M.

2013-01-01

While submarine canyons are the major conduits through which sediments are transported from the continents out into the deep sea, the time it takes for sediment to pass down through a submarine canyon system is poorly constrained. Here we report on the first study to couple optically stimulated luminescence (OSL) ages of quartz sand deposits and accelerator mass spectrometry 14C ages measured on benthic foraminifera to examine the timing of sediment transport through the axial channel of Monterey Submarine Canyon and Fan, offshore California. The OSL ages date the timing of sediment entry into the canyon head while the 14C ages of benthic foraminifera record the deposition of hemipelagic sediments that bound the sand horizons. We use both single-grain and small (∼2 mm area) single-aliquot regeneration approaches on vibracore samples from fining-upward sequences at various water depths to demonstrate relatively rapid, decadal-scale sand transport to at least 1.1 km depth and more variable decadal- to millennial-scale transport to a least 3.5 km depth on the fan. Significant differences between the time sand was last exposed at the canyon head (OSL age) and the timing of deposition of the sand (from 14C ages of benthic foraminifera in bracketing hemipelagic sediments) are interpreted as indicating that the sand does not pass through the entire canyon instantly in large individual events, but rather moves multiple times before emerging onto the fan. The increased spread in single-grain OSL dates with water depth provides evidence of mixing and temporary storage of sediment as it moves through the canyon system. The ages also indicate that the frequency of sediment transport events decreases with distance down the canyon channel system. The amalgamated sands near the canyon head yield OSL ages that are consistent with a sub-decadal recurrence frequency while the fining-upward sand sequences on the fan indicate that the channel is still experiencing events with a 150–250 year recurrence frequency out to 3.5 km water depths.    

Lower and lower Middle Pennsylvanian fluvial to estuarine deposition, central Appalachian basin: Effects of eustasy, tectonics, and climate

USGS Publications Warehouse

Greb, S.F.; Chesnut, D.R.

1996-01-01

Interpretations of Pennsylvanian sedimentation and peat accumulation commonly use examples from the Appalachian basin because of the excellent outcrops and large reserve of coal (>100 billion metric tons) in the region. Particularly controversial is the origin of Lower and lower Middle Pennsylvanian quartzose sandstones; beach-barrier, marine-bar, tidalstrait, and fluvial models all have been applied to a series of sand bodies along the western outcrop margin of the basin. Inter-pretations of these sandstones and their inferred lateral relationships are critical for understanding the relative degree of eustatic, tectonic, and climatic controls on Early Pennsylvanian sedimentation. Cross sections utilizing >1000 subsurface records and detailed sedimentological analysis of the Livingston Conglomerate, Rockcastle Sandstone, Corbin Sandstone, and Pine Creek sandstone (an informal member) of the Breathitt Group were used to show that each of the principal quartzose sandstones on the margin of the central Appalachian basin contains both fluvial and marginal marine facies. The four sandstones are fluvially dominated and are inferred to represent successive bed-load trunk systems of the Appalachian foreland. Base-level rise and an associated decrease in extra-basinal sediment at the end of each fluvial episode led to the development of local estuaries and marine reworking of the tops of the sand belts. Each of the sand belts is capped locally by a coal, regardless of whether the upper surfaces of the sand belts are of fluvial or estuarine origin, suggesting allocyclic controls on deposition. Peats were controlled by a tropical ever-wet climate, which also influenced sandstone composition through weathering of stored sands in slowly aggrading braidplains. Recurrent stacking of thick, coarse-grained, fluvial deposits with extra-basinal quartz pebbles; dominance of bed-load fluvial-lowstand deposits over mixed-load, estuarine-transgressive deposits; thinning of sand belts around tectonic highs and along faults; cratonward shift and amalgamation of successive sand belts on the margin of the basin; and truncation of successive sand belts toward the fault-bound margin of the basin are interpreted as regional responses to Alleghenian tectonism, inferred to have been the dominant control on accommodation space and sediment flux in the Early Pennsylvanian basin.

Thermal properties of alkali-activated aluminosilicates

NASA Astrophysics Data System (ADS)

Florian, Pavel; Valentova, Katerina; Fiala, Lukas; Zmeskal, Oldrich

2017-07-01

The paper is focused on measurements and evaluation of thermal properties of alkali-activated aluminosilicates (AAA) with various carbon admixtures. Such composites consisting of blast-furnace slag, quartz sand, water glass as alkali activator and small amount of electrically conductive carbon admixture exhibit better electric and thermal properties than the reference material. Such enhancement opens up new practical applications, such as designing of snow-melting, de-icing or self-sensing systems that do not need any external sensors to detect current condition of building material. Thermal properties of the studied materials were measured by the step-wise transient method and mutually compared.

Quality evaluation of carbonaceous industrial by-products and its effect on properties of autoclave aerated concrete

NASA Astrophysics Data System (ADS)

Fomina, E. V.; Lesovik, V. S.; Fomin, A. E.; Kozhukhova, N. I.; Lebedev, M. S.

2018-03-01

Argillite is a carbonaceous industrial by-product that is a potential source in environmentally friendly and source-saving construction industry. In this research, chemical and mineral composition as well as particle size distribution of argillite were studied and used to develop autoclave aerated concrete as partial substitute of quartz sand. Effect of the argillite as a mineral admixture in autoclave aerated concrete was investigated in terms of compressive and tensile strength, density, heat conductivity etc. The obtained results demonstrated an efficiency of argillite as an energy-saving material in autoclave construction composites.

Hydrogeology and flow of water in a sand and gravel aquifer contaminated by wood-preserving compounds, Pensacola, Florida

USGS Publications Warehouse

Franks, B.J.

1988-01-01

The sand and gravel aquifer in southern Escambia County, Florida , is a typical surficial aquifer composed of quartz sands and gravels interbedded locally with silts and clays. Problems of groundwater contamination from leaking surface impoundments are common in surficial aquifers and are a subject of increasing concern and attention. A potentially widespread contamination problem involves organic chemicals from wood-preserving processes. Because creosote is the most extensively used industrial preservative in the United States, an abandoned wood-treatment plant near Pensacola was chosen for investigation. This report describes the hydrogeology and groundwater flow system of the sand and gravel aquifer near the plant. A three-dimensional simulation of groundwater flow in the aquifer was evaluated under steady-state conditions. The model was calibrated on the basis of observed water levels from January 1986. Calibration criteria included reproducing all water levels within the accuracy of the data (one-half contour interval in most cases). Sensitivity analysis showed that the simulations were most sensitive to recharge and vertical leakance of the confining units between layers 1 and 2, and relatively insensitive to changes in hydraulic conductivity and transmissivity and to other changes in vertical leakance. Applications of the results of the calibrated flow model in evaluation of solute transport may require further discretization of the contaminated area, including more sublayers, than were needed for calibration of the groundwater flow system itself. (USGS)

Electrical properties of methane hydrate + sediment mixtures

USGS Publications Warehouse

Du Frane, Wyatt L.; Stern, Laura A.; Constable, Steven; Weitemeyer, Karen A.; Smith, Megan M; Roberts, Jeffery J.

2015-01-01

Knowledge of the electrical properties of multicomponent systems with gas hydrate, sediments, and pore water is needed to help relate electromagnetic (EM) measurements to specific gas hydrate concentration and distribution patterns in nature. Toward this goal, we built a pressure cell capable of measuring in situ electrical properties of multicomponent systems such that the effects of individual components and mixing relations can be assessed. We first established the temperature-dependent electrical conductivity (σ) of pure, single-phase methane hydrate to be ~5 orders of magnitude lower than seawater, a substantial contrast that can help differentiate hydrate deposits from significantly more conductive water-saturated sediments in EM field surveys. Here we report σ measurements of two-component systems in which methane hydrate is mixed with variable amounts of quartz sand or glass beads. Sand by itself has low σ but is found to increase the overall σ of mixtures with well-connected methane hydrate. Alternatively, the overall σ decreases when sand concentrations are high enough to cause gas hydrate to be poorly connected, indicating that hydrate grains provide the primary conduction path. Our measurements suggest that impurities from sand induce chemical interactions and/or doping effects that result in higher electrical conductivity with lower temperature dependence. These results can be used in the modeling of massive or two-phase gas-hydrate-bearing systems devoid of conductive pore water. Further experiments that include a free water phase are the necessary next steps toward developing complex models relevant to most natural systems.

Bacteriological Evaluation of an Ultra-Pure Water-Distilling System

PubMed Central

Kayser, W. V.; Hickman, K. C. D.; Bond, W. W.; Favero, M. S.; Carson, L. A.

1975-01-01

A prototype distillation and storage system with recycle for producing ultrapure water was monitored for bacteriological contamination during a period of 24 months. Naturally occurring Pseudomonas aeruginosa and P. cepacia were found to grow rapidly to levels of about 105/ml in water taken from the storage reservoir and also in commercially prepared distilled water. The system was found to eliminate bacterial contaminants introduced into the still with the feed water, but the reservoir, once contaminated, remained contaminated during prolonged recycle. After a single treatment with free chlorine, the entire system remained uncontaminated until accidental or purposeful shutdown. PMID:811168

A Fossilized Energy Distribution of Lightning.

PubMed

Pasek, Matthew A; Hurst, Marc

2016-07-28

When lightning strikes soil, it may generate a cylindrical tube of glass known as a fulgurite. The morphology of a fulgurite is ultimately a consequence of the energy of the lightning strike that formed it, and hence fulgurites may be useful in elucidating the energy distribution frequency of cloud-to-ground lightning. Fulgurites from sand mines in Polk County, Florida, USA were collected and analyzed to determine morphologic properties. Here we show that the energy per unit length of lightning strikes within quartz sand has a geometric mean of ~1.0 MJ/m, and that the distribution is lognormal with respect to energy per length and frequency. Energy per length is determined from fulgurites as a function of diameter, and frequency is determined both by cumulative number and by cumulative length. This distribution parallels those determined for a number of lightning parameters measured in actual atmospheric discharge events, such as charge transferred, voltage, and action integral. This methodology suggests a potential useful pathway for elucidating lightning energy and damage potential of strikes.

A Fossilized Energy Distribution of Lightning

PubMed Central

Pasek, Matthew A.; Hurst, Marc

2016-01-01

When lightning strikes soil, it may generate a cylindrical tube of glass known as a fulgurite. The morphology of a fulgurite is ultimately a consequence of the energy of the lightning strike that formed it, and hence fulgurites may be useful in elucidating the energy distribution frequency of cloud-to-ground lightning. Fulgurites from sand mines in Polk County, Florida, USA were collected and analyzed to determine morphologic properties. Here we show that the energy per unit length of lightning strikes within quartz sand has a geometric mean of ~1.0 MJ/m, and that the distribution is lognormal with respect to energy per length and frequency. Energy per length is determined from fulgurites as a function of diameter, and frequency is determined both by cumulative number and by cumulative length. This distribution parallels those determined for a number of lightning parameters measured in actual atmospheric discharge events, such as charge transferred, voltage, and action integral. This methodology suggests a potential useful pathway for elucidating lightning energy and damage potential of strikes. PMID:27466230

Gravity flow and solute dispersion in variably saturated sand

NASA Astrophysics Data System (ADS)

Kumahor, Samuel K.; de Rooij, Gerrit H.; Vogel, Hans-Joerg

2014-05-01

Solute dispersion in porous media depends on the structure of the velocity field at the pore scale. Hence, dispersion is expected to change with water content and with mean flow velocity. We performed laboratory experiments using a column of repacked fine-grained quartz sand (0.1-0.3 mm grain size) with a porous plate at the bottom to controle the water potential at the lower boundary. We established gravity flow conditions - i.e. constant matric potential and water content throughout the column - for a number of different irrigation rates. We measured breakthrough curves during unit gradient flow for an inert tracer which could be described by the convection-dispersion equation. As the soil water content decreased we observed an initially gradual increase in dispersivity followed by an abrupt increase below a threshold water content (0.19) and pressure head (-38 hPa). This phenomena can be explained by the geometry of phase distribution which was simulated based on Xray-CT images of the porous structure.

Small-scale modelling of cementation by descending silica-bearing fluids: Explanation of the origin of arenitic caves in South American tepuis

NASA Astrophysics Data System (ADS)

Aubrecht, R.; Lánczos, T.; Schlögl, J.; Audy, M.

2017-12-01

Geoscientific research was performed on South American table mountains (tepuis) and in their sandstone cave systems. To explain speleogenesis in these poorly soluble rocks, two theories were introduced: a) arenization theory implying selective weathering of quartz along grain boundaries and releasing of sand grains, b) selective lithification theory implying cementation by descending silica-bearing fluid flow. The latter theory presumes that the descending fluid flow becomes unstable on the interface between two layers with different porosity and splits to separate flow channels (so-called ;finger flow;). The arenites outside these channels remain uncemented. To verify the latter theory, small-scale modelling was performed, using layered sands and sodium-silicate solution. Fine to medium sand was used (0.08-0.5 mm), along with a coarse sand fraction (0.5-1.5 mm). The sands were layered and compacted in a transparent plastic boxes. Three liters of sodium-silicate solution (so-called water glass) were left to drip for several hours to the top of the sediment. The fine-grained layers were perfectly laterally impregnated, whereas the descending fluid flows split to ;fingers; in the coarse-grained layers due their higher hydraulic conductivity. This small-scale laboratory simulation mimics the real diagenesis by descending silica-bearing fluids and matches the real phenomena observed on the tepuis. The resulting cemented constructions closely mimic many geomorphological features observed on tepuis and inside their caves, e.g. ;finger-flow; pillars, overhangs, imperfectly formed (aborted) pillars in forms of hummocks hanging from ceilings, locally also thicker central pillars that originated by merging of smaller fluid-flow channels. The modelling showed that selective lithification theory can explain most of the geomorphological aspects related to the speleogenesis in tepuis.

Testing portable luminescence reader signals against late Pleistocene to modern OSL ages of coastal and desert dunefield sand in Israel

NASA Astrophysics Data System (ADS)

Roskin, Joel; Sivan, Dorit; Bookman, Revital; Porat, Naomi; López, Gloria I.

2017-04-01

Rapid assessment of luminescence signals of poly-mineral samples by a pulsed-photon portable OSL reader (PPSL) is useful for interpreting sedimentary sections during fieldwork, and can assist with targeted field sampling for later full OSL dating and prioritize laboratory work. This study investigates PPSL signal intensities in order to assess its usefulness in obtaining relative OSL ages from linear regressions created by interpolating newly generated PPSL values of samples with existing OSL ages from two extensive Nilotic-sourced dunefields. Eighteen OSL-dated sand samples from two quartz-dominated sand systems in Israel were studied:(1) the Mediterranean littoral-sourced coastal dunefields that formed since the middle Holocene; and (2) the inland north-western Negev desert dunefield that rapidly formed between the Last Glacial Maximum and the Holocene. Samples from three coastal dune profiles were also measured. Results show that the PPSL signals differ by several orders of magnitude between modern and late Pleistocene sediments. The coastal and desert sand have different OSL age - PPSL signal ratios. Coastal sand show better correlations between PPSL values and OSL ages. However, using regression curves for each dunefield to interpolate ages is less useful than expected as samples with different ages exhibit similar PPSL signals. The coastal dune profiles yielded low luminescence signal values depicting a modern profile chronology. This study demonstrates that a rapid assessment of the relative OSL ages across different and extensive dunefields is useful and may be achieved. However, the OSL ages obtained by linear regression are only a very rough age estimate. The reasons for not obtaining more reliable ages need to be better understood, as several variables can affect the PPSL signal such as mineral provenance, intrinsic grain properties, micro-dosimetry and moisture content.

Phenomenological Description of Acoustic Emission Processes Occurring During High-Pressure Sand Compaction

NASA Astrophysics Data System (ADS)

Delgado-Martín, Jordi; Muñoz-Ibáñez, Andrea; Grande-García, Elisa; Rodríguez-Cedrún, Borja

2016-04-01

Compaction, pore collapse and grain crushing have a significant impact over the hydrodynamic properties of sand formations. The assessment of the crushing stress threshold constitutes valuable information in order to assess the behavior of these formations provided that it can be conveniently identified. Because of the inherent complexities of the direct observation of sand crushing, different authors have developed several indirect methods, being acoustic emission a promising one. However, previous researches have evidenced that there are different processes triggering acoustic emissions which need to be carefully accounted. Worth mentioning among them are grain bearing, grain to container friction, intergranular friction and crushing. The work presented here addresses this purpose. A broadband acoustic emission sensor (PA MicroHF200) connected to a high-speed data acquisition system and control software (AeWIN for PCI1 2.10) has been attached to a steel ram and used to monitor the different processes occurring during the oedometric compaction of uniform quartz sand up to an axial load of about 110 MPa and constant temperature. Load was stepwise applied using a servocontrolled hydraulic press acting at a constant load rate. Axial strain was simultaneously measured with the aid of a LDT device. Counts, energy, event duration, rise time and amplitude were recorded along each experiment and after completion selected waveforms were transformed from the time to the frequency domain via FFT transform. Additional simplified tests were performed in order to isolate the frequency characteristics of the dominant processes occurring during sand compaction. Our results show that, from simple tests, it is possible to determine process-dependent frequency components. When considering more complex experiments, many of the studied processes overlap but it is still possible to identify when a particular one dominates as well as the likely onset of crushing.

Laboratory observations of artificial sand and oil agglomerates

USGS Publications Warehouse

Jenkins, Robert L.; Dalyander, P. Soupy; Penko, Allison; Long, Joseph W.

2018-04-27

Sand and oil agglomerates (SOAs) form when weathered oil reaches the surf zone and combines with suspended sediments. The presence of large SOAs in the form of thick mats (up to 10 centimeters [cm] in height and up to 10 square meters [m2] in area) and smaller SOAs, sometimes referred to as surface residual balls (SRBs), may lead to the re-oiling of beaches previously affected by an oil spill. A limited number of numerical modeling and field studies exist on the transport and dynamics of centimeter-scale SOAs and their interaction with the sea floor. Numerical models used to study SOAs have relied on shear-stress formulations to predict incipient motion. However, uncertainty exists as to the accuracy of applying these formulations, originally developed for sand grains in a uniformly sorted sediment bed, to larger, nonspherical SOAs. In the current effort, artificial sand and oil agglomerates (aSOAs) created with the size, density, and shape characteristics of SOAs were studied in a small-oscillatory flow tunnel. These experiments expanded the available data on SOA motion and interaction with the sea floor and were used to examine the applicability of shear-stress formulations to predict SOA mobility. Data collected during these two sets of experiments, including photographs, video, and flow velocity, are presented in this report, along with an analysis of shear-stress-based formulations for incipient motion. The results showed that shear-stress thresholds for typical quartz sand predicted the incipient motion of aSOAs with 0.5–1.0-cm diameters, but were inaccurate for aSOAs with larger diameters (>2.5 cm). This finding implies that modified parameterizations of incipient motion may be necessary under certain combinations of aSOA characteristics and environmental conditions.

Dynamics of sediments along with their core properties in the Monastir-Bekalta coastline (Tunisia, Central Mediterranean)

NASA Astrophysics Data System (ADS)

Khiari, Nouha; Atoui, Abdelfattah; Khalil, Nadia; Charef, Abdelkrim; Aleya, Lotfi

2017-10-01

The authors report on two campaigns of high-resolution samplings along the shores of Monastir Bay in Tunisia: the first being a study of sediment dynamics, grain size and mineral composition in surface sediment, and the second, eight months later, using four sediment cores to study grain-size distribution in bottom sediments. Particle size analysis of superficial sediment shows that the sand in shallow depths is characterized by S-shaped curves, indicating a certain degree of agitation, possible transport by rip currents near the bottom and hyperbolic curves illustrating heterogeneity of sand stock. The sediments settle in a relatively calm environment. Along the bay shore (from 0 to 2 m depth), the bottom is covered by medium sand. Sediment transport is noted along the coast; from north to south and from south to north, caused by longshore drift and a rip current in the middle of the bay. These two currents are generated by wind and swell, especially by north to northeast waves which transport the finest sediment. Particle size analysis of bottom sediment indicates a mean grain size ranging from coarse to very fine sands while vertical distribution of grain size tends to decrease from surface to depth. The increase in particle size of sediment cores may be due to the coexistence of terrigenous inputs along with the sedimentary transit parallel to the coast due to the effect of longshore drift. Mineralogical analysis shows that Monastir's coastal sands and bottom sediment are composed of quartz, calcite, magnesium calcite, aragonite and hematite. The existence of a low energy zone with potential to accumulate pollutants indicates that managerial action is necessary to help preserve Monastir Bay.

Detrital shocked minerals: microstructural provenance indicators of impact craters

NASA Astrophysics Data System (ADS)

Cavosie, A. J.

2014-12-01

The study of detrital shocked minerals (DSMs) merges planetary science, sedimentology, mineralogy/crystallography, accessory mineral geochemistry, and geochronology, with the goal of identifying and determining provenance of shock metamorphosed sand grains. Diagnostic high-pressure impact-generated microstructures (planar fractures, planar deformation features) are readily identified on external grain surfaces using standard SEM imaging methods (BSE), and when found, unambiguously confirm an impact origin for a given sand grain. DSMs, including quartz, zircon, monazite, and apatite, have thus far been documented at the Vredefort Dome [1,2,3], Sudbury [4], Rock Elm [5], and Santa Fe [6,7] impact structures. DSMs have been identified in alluvium, colluvium, beach sand, and glacial deposits. Two main processes are recognized that imply the global siliciclastic record contains DSMs: they survive extreme distal transport, and they survive 'deep time' lithification. Distal transport: In South Africa, shocked minerals are preserved in alluvium from the Vaal River >750 km downstream from the Vredefort impact; SHRIMP U-Pb geochronology has confirmed the origin of detrital shocked zircon and monazite from shocked Vredefort bedrock [2]. Vredefort-derived shocked zircons have also been found at the mouth of the Orange River on the Atlantic coast, having travelled ~2000 km downriver from Vredefort [8]. Deep time preservation: Vredefort-derived shocked zircon and quartz has been documented in glacial diamictite from the 300 Myr-old Dwyka Group in South Africa. Shocked minerals were thus entrained and transported in Paleozoic ice sheets that passed over Vredefort [9]. An impact crater can thus be viewed as a unique 'point source', in some cases for billions of years [2,4]; DSMs thus have applications in studying eroded impact craters, sedimentary provenance, landscape evolution, and long-term sediment transport processes throughout the geologic record. This work was supported by NSF (EAR-1145118) and NASA Astrobiology [1] Cavosie et al. 2010 GSA Bulletin. [2] Erickson et al. 2013 GCA. [3] Erickson et al. 2013 Am. Min. [4] Thomson et al. 2014 GSA Bulletin. [5] Roig et al. 2013 LPSC. [6] Lugo and Cavosie 2014 LPSC. [7] Cavosie and Lugo, 2014 LPSC. [8] Montalvo and Cavosie, 2014 GSA. [9] Pincus et al. 2014 GSA.

Distribution of hydrothermally altered rocks in the Reko Diq, Pakistan mineralized area based on spectral analysis of ASTER data

USGS Publications Warehouse

Rowan, L.C.; Schmidt, R.G.; Mars, J.C.

2006-01-01

The Reko Diq, Pakistan mineralized study area, approximately 10??km in diameter, is underlain by a central zone of hydrothermally altered rocks associated with Cu-Au mineralization. The surrounding country rocks are a variable mixture of unaltered volcanic rocks, fluvial deposits, and eolian quartz sand. Analysis of 15-band Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data of the study area, aided by laboratory spectral reflectance and spectral emittance measurements of field samples, shows that phyllically altered rocks are laterally extensive, and contain localized areas of argillically altered rocks. In the visible through shortwave-infrared (VNIR + SWIR) phyllically altered rocks are characterized by Al-OH absorption in ASTER band 6 because of molecular vibrations in muscovite, whereas argillically altered rocks have an absorption feature in band 5 resulting from alunite. Propylitically altered rocks form a peripheral zone and are present in scattered exposures within the main altered area. Chlorite and muscovite cause distinctive absorption features at 2.33 and 2.20????m, respectively, although less intense 2.33????m absorption is also present in image spectra of country rocks. Important complementary lithologic information was derived by analysis of the spectral emittance data in the 5 thermal-infrared (TIR) bands. Silicified rocks were not distinguished in the 9 VNIR + SWIR bands because of the lack of diagnostic spectral absorption features in quartz in this wavelength region. Quartz-bearing surficial deposits, as well as hydrothermally silicified rocks, were mapped in the TIR bands by using a band 13/band 12 ratio image, which is sensitive to the intensity of the quartz reststrahlen feature. Improved distinction between the quartzose surficial deposits and silicified bedrock was achieved by using matched-filter processing with TIR image spectra for reference. ?? 2006 Elsevier Inc. All rights reserved.

Impact of agglomeration state of nano- and submicron sized gold particles on pulmonary inflammation

PubMed Central

2010-01-01

Background Nanoparticle (NP) toxicity testing comes with many challenges. Characterization of the test substance is of crucial importance and in the case of NPs, agglomeration/aggregation state in physiological media needs to be considered. In this study, we have addressed the effect of agglomerated versus single particle suspensions of nano- and submicron sized gold on the inflammatory response in the lung. Rats were exposed to a single dose of 1.6 mg/kg body weight (bw) of spherical gold particles with geometric diameters of 50 nm or 250 nm diluted either by ultrapure water or by adding phosphate buffered saline (PBS). A single dose of 1.6 mg/kg bw DQ12 quartz was used as a positive control for pulmonary inflammation. Extensive characterization of the particle suspensions has been performed by determining the zetapotential, pH, gold concentration and particle size distribution. Primary particle size and particle purity has been verified using transmission electron microscopy (TEM) techniques. Pulmonary inflammation (total cell number, differential cell count and pro-inflammatory cytokines), cell damage (total protein and albumin) and cytotoxicity (alkaline phosphatase and lactate dehydrogenase) were determined in bronchoalveolar lavage fluid (BALF) and acute systemic effects in blood (total cell number, differential cell counts, fibrinogen and C-reactive protein) 3 and 24 hours post exposure. Uptake of gold particles in alveolar macrophages has been determined by TEM. Results Particles diluted in ultrapure water are well dispersed, while agglomerates are formed when diluting in PBS. The particle size of the 50 nm particles was confirmed, while the 250 nm particles appear to be 200 nm using tracking analysis and 210 nm using TEM. No major differences in pulmonary and systemic toxicity markers were observed after instillation of agglomerated versus single gold particles of different sizes. Both agglomerated as well as single nanoparticles were taken up by macrophages. Conclusion Primary particle size, gold concentration and particle purity are important features to check, since these characteristics may deviate from the manufacturer's description. Suspensions of well dispersed 50 nm and 250 nm particles as well as their agglomerates produced very mild pulmonary inflammation at the same mass based dose. We conclude that single 50 nm gold particles do not pose a greater acute hazard than their agglomerates or slightly larger gold particles when using pulmonary inflammation as a marker for toxicity. PMID:21126342

[The preparation and characterization of fine dusts carried out in the Clinica del Lavoro di Milano in support of experimental studies].

PubMed

Occella, E; Maddalon, G; Peruzzo, G F; Foà, V

1999-01-01

This paper aims to illustrate the conditions selected at the Clinica del Lavoro of the University of Milan to prepare and analyze a large number of fine dust samples produced over a period of about 50 years, that were initially used for studies within the Clinic performed in its own facilities, and since 1956 were sent to other Italian and overseas laboratories (Luxembourg, UK, Germany, Norway, Sweden, South Korea, USA). The total quantity of material distributed (with maximum size 7-10 microns) was about 2 kg and consisted of the following mineral and artificial compounds: quartz, HF-treated quartz, tridymite, HF-treated tridymite, cristobalite, chromite, anthracite, quartz sand for foundry moulds, sand from the Lybian desert, vitreous silica, pumice, cement, as well small quantities of metallic oxides, organic resins, chrysotile, crocidolite, fibres (vitreous, cotton and polyamidic). About half of the entire quantity of dusts produced consisted of partially HF-treated tridymite. Initially, research on the etiology of silicosis used quartz dust samples, simply sieved or ventilated (consisting of classes finer than 0.04 mm, containing a 15-20% respirable fraction). From 1956 to 1960 the dusts were produced by manual grinding in an agate mortar, below about 10 microns, starting from quartz from Quincinetto (near Ivrea, Province of Turin), containing about 99.5% quartz: particle size and composition were checked using an optical-petrographic technique, with identification of the free and total silica content. Subsequently, the dusts used for biological research were obtained by grinding coarse material with a cast iron pestle and planetary mills, agate and corundum jars. The grinding products were sized by means of centrifugal classification, using the selector developed by N. Zurlo, ensuring control of dust size both optically and by means of wet levigators and hydraulic classifiers (in cooperation with the Institute of Mines of Turin Polytechnic School). After 1990 pestles and rotating drum mills with autogenic grinding load were used for grinding: the size of the treated samples was reduced to 0.05 mm and an extremely fine fraction was extracted, smaller than 7-10 microns, which was used for pneumoconioses research. The characterization of the dust produced was in any case achieved by means of preliminary examination under the optical microscope (polarized light, sometimes supplemented with phase contrast), followed by quantitative analysis using chemical/petrographic, chemical diffraction or, more commonly, petrographic/diffraction techniques. Microscopic examination, if necessary supplemented with photo-micrography, was also used for particle size control, for numerical counting and subsequent reference to weight proportion. For all operational procedures the essential data on instruments and methods are reported. During studies on production, separation of fine dusts and their characterization, partly performed with support from the European Community (EEC/European Coal and Steel Commission), the following topics in particular were addressed: connections between particle size and free silica content in the measurable dust size fraction of the grinding products and in airborne dusts; characteristics of the dusts and risk indices in Italian iron and pyrite mines; possibility of abatement of the ultrafine classes of airborne dusts in pneumatically filled stopes by the addition of salts; comparison of the latest dust selectors used within the European Community; influence of the grinding methods on the results of fibrous and soft mineral measurement using X-ray diffraction analysis.

Relationship between sediment morphology and oil pollution along the Suez Canal beaches, Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barakat, M.A.K.; Shimy, T.M.; Mostafa, Y.M.

1996-10-01

In this study, marine surface sediments are collected from nine locations along the Suez Canal in order to investigate the relationship between the morphology of sands in the studied beaches and pollution by oil. Basically, the studied samples were analyzed by three techniques: grains-size analysis, microscopic examination, and gas chromatographic (GC) analysis. This study concluded that medium sand is the major class represented in the studied marine sediments. Pollution in these sand grains increases in the irregular grains more so than in the more rounded grains. Also, deep surface points, pitting, and fissures are considered to be good sites tomore » precipitate oil contamination. Also, the presence of iron oxides may be taken as evidence for tanker ballast washings. The heavy fraction (zircon) shows more contamination than the light fraction (quartz) in these samples. Finally, GC profiles have shown two types of samples: one typical of weathered or highly weathered crude oil patterns and the other for samples with very highly weathered profiles. The relationship obtained between morphology studies and both oil content and GC chromatogram profiles indicates that all of the studied locations are suffering from pollution of oil that is spilled while shipping petroleum through the Suez Canal.« less

Respiratory disease among military personnel in Saudi Arabia during Operation Desert Shield.

PubMed Central

Richards, A L; Hyams, K C; Watts, D M; Rozmajzl, P J; Woody, J N; Merrell, B R

1993-01-01

OBJECTIVES. The purpose of this study was to determine whether respiratory disease due to crowded living conditions and high levels of suspended and blowing sand had a major adverse impact on US military personnel during Operation Desert Shield. METHODS. A questionnaire survey was administered to 2598 combat troops stationed in Northeast Saudi Arabia for a mean of 102 days. Samples of surface sand from seven different locations were analyzed by scanning electron microscopy and x-ray diffraction. RESULTS. Among surveyed troops, 34.4% reported a sore throat, 43.1% complained of a cough, 15.4% complained of chronic rhinorrhea, and 1.8% were unable to perform their routine duties because of upper respiratory symptoms. Evaluation of sleeping accommodations indicated that complaints of a sore throat and cough were most closely associated with sleeping in air-conditioned buildings; in contrast, complaints of rhinorrhea were associated with exposure to the outdoor environment while living in tents. Sand samples consisted mostly of quartz, with just 0.21% by weight of respirable size (< 10 microns in diameter). CONCLUSIONS. These findings indicate that upper respiratory complaints were frequent among Operation Desert Shield troops and were related both to the troops' housing and to their exposure to the outside environment. PMID:8363011

Research on Annular Frictional Pressure Loss of Hydraulic-Fracturing in Buckling Coiled Tubing

NASA Astrophysics Data System (ADS)

Liu, Bin; Cai, Meng; Li, Junliang; Xu, Yongquan; Wang, Peng

2018-01-01

Compared with conventional hydraulic fracturing, coiled tubing (CT) annular delivery sand fracturing technology is a new method to enhance the recovery ratio of low permeability reservoir. Friction pressure loss through CT has been a concern in fracturing. The small diameter of CT limits the cross-sectional area open to flow, therefore, to meet large discharge capacity, annular delivery sand technology has been gradually developed in oilfield. Friction pressure is useful for determining the required pump horsepower and fracturing construction design programs. Coiled tubing can buckle when the axial compressive load acting on the tubing is greater than critical buckling load, then the geometry shape of annular will change. Annular friction pressure loss elevates dramatically with increasing of discharge capacity, especially eccentricity and CT buckling. Despite the frequency occurrence of CT buckling in oilfield operations, traditionally annular flow frictional pressure loss considered concentric and eccentric annuli, not discussing the effects of for discharge capacity and sand ratio varying degree of CT buckling. The measured data shows that the factors mentioned above cannot be ignored in the prediction of annular pressure loss. It is necessary to carry out analysis of annulus flow pressure drop loss in coiled tubing annular with the methods of theoretical analysis and numerical simulation. Coiled tubing buckling has great influence on pressure loss of fracturing fluid. Therefore, the correlations have been developed for turbulent flow of Newtonian fluids and Two-phase flow (sand-liquid), and that improve the friction pressure loss estimation in coiled tubing operations involving a considerable level of buckling. Quartz sand evidently increases pressure loss in buckling annular, rising as high as 40%-60% more than fresh water. Meanwhile, annulus flow wetted perimeter increases with decreasing helical buckling pitch of coiled tubing, therefore, the annulus flow frictional pressure loss rapidly increases with decreasing helical buckling pitch. The research achievement provides theoretical guidance for coiled tubing annular delivery sand fracturing operation and design.

Fault gouge rheology under confined, high-velocity conditions

NASA Astrophysics Data System (ADS)

Reches, Z.; Madden, A. S.; Chen, X.

2012-12-01

We recently developed the experimental capability to investigate the shear properties of fine-grain gouge under confined conditions and high-velocity. The experimental system includes a rotary apparatus that can apply large displacements of tens of meters, slip velocity of 0.001- 2.0 m/s, and normal stress of 35 MPa (Reches and Lockner, 2010). The key new component is a Confined ROtary Cell (CROC) that can shear a gouge layer either dry or under pore-pressure. The pore pressure is controlled by two syringe pumps. CROC includes a ring-shape gouge chamber of 62.5 mm inner diameter, 81.25 mm outer diameter, and up to 3 mm thick gouge sample. The lower, rotating part of CROC contains the sample chamber, and the upper, stationary part includes the loading, hollow cylinder and setting for temperature, and dilation measurements, and pore-pressure control. Each side of the gouge chamber has two pairs of industrial, spring-energized, self-lubricating, teflon-graphite seals, built for particle media and can work at temperature up to 250 ded C. The space between each of the two sets of seals is pressurized by nitrogen. This design generates 'zero-differential pressure' on the inner seal (which is in contact with the gouge powder), and prevents gouge leaks. For the preliminary dry experiments, we used ~2.0 mm thick layers of room-dry kaolinite powder. Total displacements were on the order of meters and normal stress up to 4 MPa. The initial shear was accommodated by multiple internal slip surfaces within the kaolinite layer accommodated as oriented Riedel shear structures. Later, the shear was localized within a thin, plate-parallel Y-surface. The kaolinite layer was compacted at a quasi-asymptotic rate, and displayed a steady-state friction coefficient of ~ 0.5 with no clear dependence on slip velocity up to 0.15 m/s. Further experiments with loose quartz sand (grain size ~ 125 micron) included both dry runs and pore-pressure (distilled water) controlled runs. The sand was pressurized through a porous metal (Mott) plug. Comparison with effective stress calculations indicates the same friction coefficient of ~ 1.0 for the sand layer under dry and pressurized conditions. Both kaolinite and quartz sand experiments developed localized shear zones that were examined at the nano- and micro- scales with AFM, SEM and TEM. These zones displayed reduced grain sizes and cementation by local agglomeration. Kaolinite grains sheared in CROC experiment; scale bar = 1 micron.

Test well DO-CE 88 at Cambridge, Dorchester County, Maryland

USGS Publications Warehouse

Trapp, Henry; Knobel, LeRoy L.; Meisler, Harold; Leahy, P. Patrick

1984-01-01

Test well DO-CE 88 at Cambridge, Maryland, penetrated 3,299 feet of unconsolidated Quaternary, Tertiary and Cretaceous sediments and bottomed in quartz-monzonite gneiss. The well was drilled to provide data for a study of the aquifer system of the northern Atlantic Coastal Plain. Twenty-one core samples were collected. Six sand zones were tested for aquifer properties and sampled for ground-water chemistry. Point-water heads were measured at seven depths. Environmental heads (which ranged from - 18.33 to + 44.16 feet relative to sea level)indicate an upward component of flow. A temperature log showed a maximum temperature of 41.9 degrees Celsius and a mean temperature gradient of 0.00838 degrees Celsius per foot. The water analyses delineated the freshwater-saltwater transition zone between 2,650 and 3,100 feet. The ground water changes progressively downward from a sodium bicarbonate to a sodium chloride character. Clays in the analyzed core samples belong to the montmorillonite and kaolinite groups, and mean cation exchange capacity ranged from 8.3 to 38.9 milliequivalents per 100 grams. Vertical and horizontal hydraulic conductivities measured in cores ranged from 1.5 x 10 6 to 1.3 feet per day and from 7.3 x 10 -6 to 1.3 feet per day, respectively, but the most permeable sands were not cored. Porosity was 1.5 percent in the quartz monzonite bedrock and ranged from 22.4 to 41 percent in the overlying sediments. Transmissivities from aquifer tests ranged from 25 to 850 feet squared per day; horizontal hydraulic conductivities ranged from.2.5 to 85 feet squared per day, and intrinsic permeabilities ranged from 0.8 to 23 micrometers squared. Fossils identified in core samples include palynomorphs, dinoflagellates, and foraminifers.

In situ Fe-sulfide coating for arsenic removal under reducing conditions

NASA Astrophysics Data System (ADS)

Xie, Xianjun; Liu, Yaqing; Pi, Kunfu; Liu, Chongxuan; Li, Junxia; Duan, Mengyu; Wang, Yanxin

2016-03-01

An in situ Fe-sulfide coating approach has been developed for As-contaminated groundwater remediation. Alternate injection of Fe(II), O2-free water and S2- can realize Fe-sulfide coating onto quartz sands with minor changes in porosity. As(III) uptake experiment indicated that the retardation factor for As(III) was 37 and dynamic retention capacity was 44.94 mg As(III)/g Fe, which was much higher than the maximum adsorption capacity for As(III) by FeS and FeS2. This result indicated that adsorption cannot be the only mechanism for As(III) uptake by Fe-sulfide coating layer. The SEM image and FTIR spectra results suggested that interaction between As(III) and Fe-sulfides and formation of As-sulfide precipitates could significantly contribute to As(III) uptake by Fe-sulfide coating layer. Alternate injection of Fe(II) + As(III) and S2- was conducted to simulate in situ As immobilization from real groundwater. The SEM image showed that the quartz sands were mainly covered by crystalline framboidal pyrite after such amendment. The breakthrough of As(III) was not observed during this experiment and the removal capacity for As(III) was 109.7 mg As/g Fe. The As(III) immobilization mechanism during alternate injection of Fe(II) + As(III) and S2- was significantly different from that of As(III) uptake by Fe-sulfide coating. The direct interaction between As(III) and S2- produced As-sulfides contributed to the high As(III) removal capacity during alternate injection of Fe(II) + As(III) and S2-. This result indicated that alternate injection of Fe(II) and S2- approach has an attractive application for As-contaminated groundwater remediation under strongly reducing environment.

Pheromone disruption of Argentine ant trail integrity.

PubMed

Suckling, D M; Peck, R W; Manning, L M; Stringer, L D; Cappadonna, J; El-Sayed, A M

2008-12-01

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m(2)) to 1- and 4-m(2) plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected.

Twenty years of sedimentary change and diagenesis, Qatar Peninsula, Arabian Gulf

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shinn, E.A.

Re-examination in February 1986 of areas studied by the author in 1966 and 1967 revealed rapid rates of sedimentation and diagenesis along the east coast of the Qatar Peninsula. At Ras Um Sa on the north-east side of Qatar, a series of chenier-like beaches and curved spits is building southward under the influence of longshore currents. Beach and spit growth increasingly protects the shoreline and allows tidal flats to form in their lee. As these spits accrete, they become armored on their lagoonal side by beachrock formation. In the last 20 years a spit approximately 1/2 km long has grown,more » and beachrock has already armored its recurved lagoonal side. At Umm Said on the southeast side of Qatar, seawardly accreting barchan dunes composed of quartz sand have built a 40-km long, 10-km wide sabkha as thick as 30 m. Aerial and ground photographs show that certain dunes near the seaward edge of the sabkha have migrated into the sea and have contributed to shoreline accretion. The observed rate of dune migration suggests that within approximately 100 years the remaining quartz sands will be depleted and blown into the sea because there is no replenishment of the dune field. Subsequently, the area will revert to one of carbonate deposition. Fine-grained dolomite is presently precipitating in interstitial brines in the landwardmost portions of this unusual sabkha. In the geologic record, such a deposit would be an anomalous, porous and permeable, cross-bedded, linear, 30-m thick, dolomite-cemented sandstone body encased in carbonate sediments. A modern model such as the one at Umm Said can provide useful clues for determining the origin of similar deposits in ancient rocks.« less

Twenty years of sedimentary change and diagenesis, Qatar Peninsula, Arabian Gulf

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shinn, E.A.

Re-examination in February 1986 of areas studied by the author in 1966 and 1967 revealed rapid rates of sedimentation and diagenesis along the east coast of the Qatar Peninsula. At Ras UmSa on the northeast side of Qatar, a series of chenier-like beaches and curved spits is building southward under the influence of longshore currents. Beach and spit growth increasingly protects the shoreline and allows tidal flats to form in their lee. As these spits accrete, they become armored on their lagoonal side by beachrock formation. In the last 20 years a spit approximately 1/2 km long has grown, andmore » beachrock has already armored its recurved lagoonal side. At Umm Said on the southeast side of Qatar, seawardly accreting barchan dunes composed of quartz sand have built a 40-km long, 10-km wide sabkha as thick as 30 m. Aerial and ground photographs show that certain dunes near the seaward edge of the sabkha have migrated into the sea and have contributed to shoreline accretion. The observed rate of dune migration suggests that within approximately 100 years the remaining quartz sands are depleted and blown into the sea because there is no replenishment of the dune field. Subsequently, the area reverts to one of carbonate deposition. Fine-grained dolomite is presently precipitating in interstitial brines in the landwardmost portions of this unusual sabkha. In the geologic record, such a deposit would be an anomalous, porous and permeable, cross-bedded, linear, 30-m thick, dolomite-cemented sandstones body encased in carbonate sediments. A modern model such as the one at Umm Said can provide useful clues for determining the origin of similar deposits in ancient rocks.« less

Petrographic and reservoir features of Hauterivian (Lower Cretaceous) Shatlyk horizon in the Malay gas field, Amu-Darya basin, east Turkmenia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naz, H.; Ersan, A.

1996-08-01

Malay gas field in Amu-Darya basin, eastern Turkmenia, is located on the structural high that is on the Malay-Bagadzha arch north of the Repetek-Kelif structure zone. With 500 km{sup 2} areal coverage, 16 producing wells and 200 billion m{sup 3} estimated reserves, the field was discovered in 1978 and production began in 1987 from 2400-m-deep Hauterivian-age (Early Cretaceous) Shatlyk horizon. The Shatlyk elastic sequence shows various thickness up to 100 m in the Malay structural closure and is studied through E-log, core, petrographic data and reservoir characteristics. The Shatlyk consists of poorly indurated, reddish-brown and gray sandstones, and sandy graymore » shales. The overall sand-shale ratio increases up and the shales interleave between the sand packages. The reservoir sandstones are very fine to medium grained, moderately sorted, compositionally immature, subarkosic arenites. The framework grains include quartz, feldspar and volcanic lithic fragments. Quartz grains are monocrystalline in type and most are volcanic in origin. Feldspars consist of K- Feldspar and plagioclase. The orthoclases are affected by preferential alteration. The sandstones show high primary intergranular porosity and variations in permeability. Patch-like evaporate cement and the iron-rich grain coatings are reducing effects in permeability. The coats are pervasive in reddish-brown sandstones but are not observed in the gray sandstones. The evaporate cement is present in all the sandstone samples examined and, in places, follows the oxidation coats. The petrographic evidences and the regional facies studies suggest the deposition in intersection area from continental to marine nearshore deltaic environment.« less

Geochemical hosts of solubilized radionuclides in uranium mill tailings

USGS Publications Warehouse

Landa, E.R.; Bush, C.A.

1990-01-01

The solubilization and subsequent resorption of radionuclides by ore components or by reaction products during the milling of uranium ores may have both economic and environmental consequences. Particle-size redistribution of radium during milling has been demonstrated by previous investigators; however, the identification of sorbing components in the tailings has received little experimental attention. In this study, uranium-bearing sandstone ore was milled, on a laboratory scale, with sulfuric acid. At regular intervals, filtrate from this suspension was placed in contact with mixtures of quartz sand and various potential sorbents which occur as gangue in uranium ores; the potential sorbents included clay minerals, iron and aluminum oxides, feldspar, fluorspar, barite, jarosite, coal, and volcanic glass. After equilibration, the quartz sand-sorbent mixtures were separated from the filtrate and radioassayed by gamma-spectrometry to determine the quantities of 238U, 230Th, 226Ra, and 210Pb sorbed, and the radon emanation coefficients. Sorption of 238U was low in all cases, with maximal sorptions of 1-2% by the bentonite- and coal-bearing samples. 230Th sorption also was generally less than 1%; maximal sorption here was observed in the fluorspar-bearing sample and appears to be associated with the formation of gypsum during milling. 226Ra and 210 Pb generally showed higher sorption than the other nuclides - more than 60% of the 26Ra solubilized from the ore was sorbed on the barite-bearing sample. The mechanism (s) for this sorption by a wide variety of substrates is not yet understood. Radon emanation coefficients of the samples ranged from about 5 to 30%, with the coal-bearing samples clearly demonstrating an emanating power higher than any of the other materials. ?? 1990.

Pheromone disruption of Argentine ant trail integrity

USGS Publications Warehouse

Suckling, D.M.; Peck, R.W.; Manning, L.M.; Stringer, L.D.; Cappadonna, J.; El-Sayed, A. M.

2008-01-01

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m2) to 1- and 4-m2 plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected. ?? 2008 Springer Science+Business Media, LLC.

Critical bed shear stress and threshold of motion of maerl biogenic gravel

NASA Astrophysics Data System (ADS)

Joshi, Siddhi; Duffy, Garret Patrick; Brown, Colin

2017-07-01

A determination of the critical bed shear stress of maerl is a prerequisite for quantifying its mobility, rate of erosion and deposition in conservation management. The critical bed shear stress for incipient motion has been determined for the first time for samples from biogenic free-living maerl beds in three contrasting environments (open marine, intertidal and beach) in Galway Bay, west of Ireland. The bed shear stress was determined using two methods, Law of the Wall and Turbulent Kinetic Energy, in a rotating annular flume and in a linear flume. The velocity profile of flowing water above a bed of natural maerl grains was measured in four runs of progressively increasing flow velocity until the flow exceeded the critical shear stress of grains on the bed. The critical Shields parameter and the mobility number are estimated and compared with the equivalent curves for natural quartz sand. The critical Shields parameters for the maerl particles from all three environments fall below the Shields curve. Along with a previously reported correlation between maerl grain shape and settling velocity, these results suggest that the highly irregular shapes also allow maerl grains to be mobilised more easily than quartz grains with the same sieve diameter. The intertidal beds with the roughest particles exhibit the greatest critical shear stress because the particle thalli interlock and resist entrainment. In samples with a high percentage of maerl and low percentage of siliciclastic sand, the lower density, lower settling velocity and lower critical bed shear stress of maerl results in its preferential transport over the siliciclastic sediment. At velocities ∼10 cm s-1 higher than the threshold velocity of grain motion, rarely-documented subaqueous maerl dunes formed in the annular flume.

In situ Fe-sulfide coating for arsenic removal under reducing conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Xianjun; Liu, Yaqing; Pi, Kunfu

2016-03-01

An in situ Fe-sulfide coating approach has been developed for As-contaminated groundwater remediation. Alternate injection of Fe(II), O 2-free water and S 2$-$ can realize Fe-sulfide coating onto quartz sands with minor changes in porosity. As(III) uptake experiment indicated that the retardation factor for As(III) was 37 and dynamic retention capacity was 44.94 mg As(III)/g Fe, which was much higher than the maximum adsorption capacity for As(III) by FeS and FeS 2. This result indicated that adsorption cannot be the only mechanism for As(III) uptake by Fe-sulfide coating layer. The SEM image and FTIR spectra results suggested that interaction betweenmore » As(III) and Fe-sulfides and formation of As-sulfide precipitates could significantly contribute to As(III) uptake by Fe-sulfide coating layer. Alternate injection of Fe(II) + As(III) and S 2$-$ was conducted to simulate in situ As immobilization from real groundwater. The SEM image showed that the quartz sands were mainly covered by crystalline framboidal pyrite after such amendment. The breakthrough of As(III) was not observed during this experiment and the removal capacity for As(III) was 109.7 mg As/g Fe. The As(III) immobilization mechanism during alternate injection of Fe(II) + As(III) and S 2$-$ was significantly different from that of As(III) uptake by Fe-sulfide coating. The direct interaction between As(III) and S 2$-$ produced As-sulfides contributed to the high As(III) removal capacity during alternate injection of Fe(II) + As(III) and S 2$-$. This result indicated that alternate injection of Fe(II) and S 2$-$ approach has an attractive application for As-contaminated groundwater remediation under strongly reducing environment.« less

Semi-conducting single-walled carbon nanotubes are detrimental when compared to metallic single-walled carbon nanotubes for electrochemical applications.

PubMed

Dong, Qi; Nasir, Muhammad Zafir Mohamad; Pumera, Martin

2017-10-18

As-synthetized single walled carbon nanotubes (SWCNTs) contain both metallic and semiconducting nanotubes. For the electronics, it is desirable to separate semiconducting SWCNTs (s-SWCNTs) from the metallic ones as s-SWCNTs provide desirable electronic properties. Here we test whether ultrapure semi-conducting single-walled carbon nanotubes (s-SWCNTs) provide advantageous electrochemical properties over the as prepared SWCNTs which contain a mixture of semiconducting and metallic CNTs. We test them as a transducer platform which enhanced the detection of target analytes (ascorbic acid, dopamine, uric acid) when compared to a bare glassy carbon (GC) electrode. Despite that, the two materials exhibit significantly different electrochemical properties and performances. A mixture of m-SWCNTs and s-SWCNTs demonstrated superior performance over ultrapure s-SWCNTs with greater peak currents and pronounced shift in peak potentials to lower values in cyclic and differential pulse voltammetry for the detection of target analytes. The mixture of m- and s-SWCNTs displayed about a 4 times improved heterogeneous electron transfer rate as compared to bare GC and a 2 times greater heterogeneous electron transfer rate than s-SWCNTs, demonstrating that ultrapure SWCNTs do not provide any major enhancement over the as prepared SWCNTs.

The Karakum and Kyzylkum sand seas dynamics; mapping and palaeoclimatic interpretations

NASA Astrophysics Data System (ADS)

Maman, Shimrit; Blumberg, Dan G.; Tsoar, Haim; Porat, Naomi

2015-04-01

Sand seas are large basins in deserts that are mantled by wind-swept sand and that exhibit varying degrees of vegetation cover. Wilson (1973) was the first to globally map and classify sand seas. Beyond Wilson's maps, however, little research has been published regarding the Karakum and Kyzylkum sand seas of Central Asia. Wilson's maps delineate active ergs from inactive ergs based solely on precipitation. His assumption of annual average rainfall as a factor determining mobility vs. stability of sand seas is too simplistic and does not take into consideration other factors such as biogenic soil crusts and wind power, both of which are known to have major effects on the dynamics of sand dunes. Literature related to mapping and classifying the Central Asian ergs by remote sensing or sand sea classification state (stable/active) is lacking. Moreover, the palaeoclimatic significance of dunes in Central Asia is difficult to assess, as there has been few studies of dune stratigraphy and numerical ages are lacking. Optically stimulated luminescence (OSL) is a firm optical dating method that is used to determine the elapsed time since quartz grains were last exposed to sunlight, thus, their burial. Yet, absolute ages indicating mobilization and stabilization of these sands, are still inadequately known and are here under discussion. The broad concern of this research was to determine the dynamics of the Central Asian sand seas and study the palaeoclimatic changes that brought to their stabilization. As there are no reliable maps or aeolian discussion of these sands, establishment of a digital data base was initially conducted, focusing on identifying and mapping these sand seas. The vast area and inaccessibility make traditional mapping methods virtually impossible. A variety of space-borne imagery both optical and radar, with varying spectral and spatial resolutions was used. These images provided the basis for mapping sand distribution, dune forms, and vegetation cover. GIS analysis was performed in parallel with field work to obtain validation and verification. The remote sensing and GIS results show that these ergs are mostly stabilized, with the estimated sand mantled area for the Karakum desert ~260,000 km2, and for the Kyzylkum it is ~195,500 km2. Meteorological analysis of wind and precipitation data indicate a low wind power environment (DP< 200) and sufficient rainfall (>100 mm) to support vegetation. Thus, these sands are indicative of past periods during which the climate in this region was different than today, enabling aeolian sand activity. Optically stimulated luminescence ages derived from the upper meter of the interdune of 14 exposed sections from both ergs, indicate sand stabilization during the mid-Holocene. This stabilization is understood to reflect a transition to a warmer, wetter, and less windy climate that generally persisted until today. The OSL ages, coupled with a compilation of regional palaeoclimatic data, corroborate and reinforce the previously proposed Mid-Holocene Liavliakan phase, known to reflect a warmer, wetter, and less windy climate that persists until today and resulted in dune stabilization around the Mid-Holocene.

Hydrogeology of the gray limestone aquifer in southern Florida

USGS Publications Warehouse

Reese, Ronald S.; Cunningham, Kevin J.

2000-01-01

Results from 35 new test coreholes and aquifer-test, water-level, and water-quality data were combined with existing hydrogeologic data to define the extent, thickness, hydraulic properties, and degree of confinement of the gray limestone aquifer in southern Florida. This aquifer, previously known to be present only in southeastern Florida (Miami-Dade, Broward, and Palm Beach Counties) below, and to the west of, the Biscayne aquifer, extends over most of central-south Florida, including eastern and central Collier County and southern Hendry County; it is the same as the lower Tamiami aquifer to the north, and it becomes the water-table aquifer and the upper limestone part of the lower Tamiami aquifer to the west. The aquifer generally is composed of gray, shelly, lightly to moderately cemented limestone with abundant shell fragments or carbonate sand, abundant skeletal moldic porosity, and minor quartz sand. The gray limestone aquifer comprises the Ochopee Limestone of the Tamiami Formation, and, in some areas, the uppermost permeable part of an unnamed formation principally composed of quartz sand. Underlying the unnamed formation is the Peace River Formation of the upper Hawthorn Group, the top of which is the base of the surficial aquifer system. Overlying the aquifer and providing confinement in much of the area is the Pinecrest Sand Member of the Tamiami Formation. The thickness of the aquifer is comparatively uniform, generally ranging from 30 to 100 feet. The unnamed formation part of the aquifer is up to 20 feet thick. The Ochopee Limestone accumulated in a carbonate ramp depositional system and contains a heterozoan carbonate-particle association. The principal rock types of the aquifer are pelecypod lime rudstones and floatstones and permeable quartz sands and sandstones. The pore types are mainly intergrain and separate vug (skeletal-moldic) pore spaces. The rock fabric and associated primary and secondary pore spaces combine to form a dual diffuse-carbonate and conduit flow system capable of producing high values of hydraulic conductivity. Transmissivity values of the aquifer are commonly greater than 50,000 feet squared per day to the west of Miami-Dade and Broward Counties. Hydraulic conductivity ranges from about 200 to 12,000 feet per day and generally increases from east to west; an east-to-west shallowing of the depositional profile of the Ochopee Limestone carbonate ramp contributes to this spatial trend. The aquifer contains two areas of high transmissivity, both of which trend northwest-southeast. One area extends through southern Hendry County. The other area extends through eastern Collier County, with a transmissivity as high as 300,000 feet squared per day; in this area, the aquifer is structurally high, the top of the aquifer is close to land surface, and it is unconfined to semiconfined. The confinement of the aquifer is good to the north and east in parts of southern Hendry, Palm Beach, Collier, Broward, and Miami-Dade Counties. In these areas, the upper confining unit approaches or is greater than 50 feet thick, and vertical leakance is less than 1.0 x 10-3 l/day. In most of the study area, the specific conductance in water from the gray limestone aquifer is 1,500 microsiemens per centimeter or less (chloride concentration of about 250 milligrams per liter or less). Areas where specific conductance is greater than 3,000 microsiemens per centimeter are found where there is a low horizontal-head gradient and the upper confining unit is greater than 50 feet thick. An area with specific conductance less than 1,500 microsiemens per centimeter extends from southern Hendry County to the southeast into western Broward County and coincides with an area of high transmissivity. However, much of this area has good confinement. The potentiometric gradient also is to the southeast in much of the area, and this area of low specific conductance is probably caused by a relatively rapid downgradient movement of fres

Spectral characterization of surface emissivities in the thermal infrared

NASA Astrophysics Data System (ADS)

Niclòs, Raquel; Mira, Maria; Valor, Enric; Caselles, Diego; García-Santos, Vicente; Caselles, Vicente; Sánchez, Juan M.

2015-04-01

Thermal infrared (TIR) remote sensing trends to hyperspectral sensors on board satellites in the last decades, e.g., the current EOS-MODIS and EOS-ASTER and future missions like HyspIRI, ECOSTRESS, THIRSTY and MISTIGRI. This study aims to characterize spectrally the emissive properties of several surfaces, mostly soils. A spectrometer ranging from 2 to 16 μm, D&P Model 102, has been used to measure samples with singular spectral features, e.g. a sandy soil rich in gypsum sampled in White Sands (New Mexico, USA), salt samples, powdered quartz, and powdered calcite. These samples were chosen for their role in the assessment of thermal emissivity of soils, e.g., the calcite and quartz contents are key variables for modeling TIR emissivities of bare soils, along with soil moisture and organic matter. Additionally, the existence of large areas in the world with abundance of these materials, some of them used for calibration/validation activities of satellite sensors and products, makes the chosen samples interesting. White Sands is the world's largest gypsum dune field encompassing 400 km^2; the salt samples characterize the Salar of Uyuni (Bolivia), the largest salt flat in the world (up to 10,000 km^2), as well as the Jordanian and Israeli salt evaporation ponds at the south end of the Dead Sea, or the evaporation lagoons in Aigües-Mortes (France); and quartz is omnipresent in most of the arid regions of the world such as the Algodones Dunes or Kelso Dunes (California, USA), with areas around 700 km2 and 120 km^2, respectively. Measurements of target leaving radiance, hemispherical radiance reflected by a diffuse reflectance panel, and the radiance from a black body at different temperatures were taken to obtain thermal spectra with the D&P spectrometer. The good consistency observed between our measurements and laboratory spectra of similar samples (ASTER and MODIS spectral libraries) indicated the validity of the measurement protocol. Further, our study showed the high precision achieved by in situ spectra of real covers (instead of laboratory measurements over microscopic portions of samples). Several spectral features were observed: 1) the high spectral contrast of gypsum in the TIR, which emissivity decreases from 0.98 up to 0.70 around 8.6 μm, 2) the broad absorption band of salt in the infrared (low emissivity at wavelengths lower than 16.7 μm), 3) the weak absorption feature of the quartz Reststrahlen bands (low emissivity between 7.7 and 9.7 μm, and near 12.6 μm), and 4) the absorption features near 11.4 μm and 14.0 μm characteristics of calcite.

Application of fluid-rock reaction studies to in situ recovery from oil sand deposits, Alberta, Canada - I. Aqueous phase results for an experimental-statistical study of water-bitumen-shale reactions

NASA Astrophysics Data System (ADS)

Boon, J. A.; Hitchon, Brian

1983-02-01

In situ recovery operations in oil sand deposits effectively represent man-imposed low to intermediate temperature metamorphism of the sediments in the deposit. In order to evaluate some of the reactions which occur, a factorial experiment was earned out in which a shale from the Lower Cretaceous McMurray Formation in the Athabasca oil sand deposit of Alberta, in the presence or absence of bitumen, was subjected to hydrothermal treatment with aqueous fluids of varying pH and salinity, at two different temperatures, for periods up to 92 hours. The aqueous fluid was analyzed and the analytical data subjected to statistical factor analysis and analysis of variance, which enabled identification of the main processes, namely, cation exchange, the production of two types of colloidal material, and the dissolution of quartz There is also saturation of the aqueous phase by. as yet unidentified, "total organic carbon" and complete conversion and removal of all nitrogen in the shale to the aqueous phase. These reactions have implications with regards to the economics of the in situ recovery process, specifically with respect to the reuse and/or disposal of the produced water and the plugging of the pore space and hence of reduction of permeability between the injection and production wells. As a result of these experiments it is suggested that monitoring of the composition of the produced water from in situ recovery operations in oil sand deposits would be advisable.

Electrical properties of methane hydrate + sediment mixtures: The σ of CH 4 Hydrate + Sediment

DOE PAGES

Du Frane, Wyatt L.; Stern, Laura A.; Constable, Steven; ...

2015-07-30

Knowledge of the electrical properties of multicomponent systems with gas hydrate, sediments, and pore water is needed to help relate electromagnetic (EM) measurements to specific gas hydrate concentration and distribution patterns in nature. We built a pressure cell capable of measuring in situ electrical properties of multicomponent systems such that the effects of individual components and mixing relations can be assessed. We first established the temperature-dependent electrical conductivity (σ) of pure, single-phase methane hydrate to be ~5 orders of magnitude lower than seawater, a substantial contrast that can help differentiate hydrate deposits from significantly more conductive water-saturated sediments in EMmore » field surveys. We report σ measurements of two-component systems in which methane hydrate is mixed with variable amounts of quartz sand or glass beads. Sand by itself has low σ but is found to increase the overall σ of mixtures with well-connected methane hydrate. Alternatively, the overall σ decreases when sand concentrations are high enough to cause gas hydrate to be poorly connected, indicating that hydrate grains provide the primary conduction path. Our measurements suggest that impurities from sand induce chemical interactions and/or doping effects that result in higher electrical conductivity with lower temperature dependence. Finally, these results can be used in the modeling of massive or two-phase gas-hydrate-bearing systems devoid of conductive pore water. Further experiments that include a free water phase are the necessary next steps toward developing complex models relevant to most natural systems.« less

4D Imaging of Salt Precipitation during Evaporation from Saline Porous Media Influenced by the Particle Size Distribution

NASA Astrophysics Data System (ADS)

Norouzi Rad, M.; Shokri, N.

2014-12-01

Understanding the physics of water evaporation from saline porous media is important in many processes such as evaporation from porous media, vegetation, plant growth, biodiversity in soil, and durability of building materials. To investigate the effect of particle size distribution on the dynamics of salt precipitation in saline porous media during evaporation, we applied X-ray micro-tomography technique. Six samples of quartz sand with different grain size distributions were used in the present study enabling us to constrain the effects of particle and pore sizes on salt precipitation patterns and dynamics. The pore size distributions were computed using the pore-scale X-ray images. The packed beds were saturated with NaCl solution of 3 Molal and the X-ray imaging was continued for one day with temporal resolution of 30 min resulting in pore scale information about the evaporation and precipitation dynamics. Our results show more precipitation at the early stage of the evaporation in the case of sand with the larger particle size due to the presence of fewer evaporation sites at the surface. The presence of more preferential evaporation sites at the surface of finer sands significantly modified the patterns and thickness of the salt crust deposited on the surface such that a thinner salt crust was formed in the case of sand with smaller particle size covering larger area at the surface as opposed to the thicker patchy crusts in samples with larger particle sizes. Our results provide new insights regarding the physics of salt precipitation in porous media during evaporation.

Electrical properties of methane hydrate + sediment mixtures: The σ of CH 4 Hydrate + Sediment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Du Frane, Wyatt L.; Stern, Laura A.; Constable, Steven

Knowledge of the electrical properties of multicomponent systems with gas hydrate, sediments, and pore water is needed to help relate electromagnetic (EM) measurements to specific gas hydrate concentration and distribution patterns in nature. We built a pressure cell capable of measuring in situ electrical properties of multicomponent systems such that the effects of individual components and mixing relations can be assessed. We first established the temperature-dependent electrical conductivity (σ) of pure, single-phase methane hydrate to be ~5 orders of magnitude lower than seawater, a substantial contrast that can help differentiate hydrate deposits from significantly more conductive water-saturated sediments in EMmore » field surveys. We report σ measurements of two-component systems in which methane hydrate is mixed with variable amounts of quartz sand or glass beads. Sand by itself has low σ but is found to increase the overall σ of mixtures with well-connected methane hydrate. Alternatively, the overall σ decreases when sand concentrations are high enough to cause gas hydrate to be poorly connected, indicating that hydrate grains provide the primary conduction path. Our measurements suggest that impurities from sand induce chemical interactions and/or doping effects that result in higher electrical conductivity with lower temperature dependence. Finally, these results can be used in the modeling of massive or two-phase gas-hydrate-bearing systems devoid of conductive pore water. Further experiments that include a free water phase are the necessary next steps toward developing complex models relevant to most natural systems.« less

Silicon material development for terrestrial solar cells. Phase of exploration

NASA Astrophysics Data System (ADS)

Sirtl, E.

1983-03-01

A material project based on a multicrystalline silicon is reported. It consists of refining the metallurgical grade silicon via hydro and pyrometallurgical processes, preparation of square shaped ingots by (inert) gas protected or open hearth casting methods, and high speed slicing, using a multiple blade slurry saw. Second generation pilot equipment was constructed. Aluminothermic reduction of quartz sand into silicon and the foil casting process were tested. It is concluded that the production of silicon thru the gaseous phase depends upon the marketing of very cheap basic material (SG-Si 10 dollar/Kg) and that the purification of metallurgical grade silicon by refining is the most promising method.

Highway pavement performance test for colored thin anti-skidding layers

NASA Astrophysics Data System (ADS)

Gao, Wei; Cui, Wei; Xu, Ming

2018-03-01

Based on the actual service condition of highway pavement colored thin anti-skidding layers, with materials of color quartz sand and two-component acrylic resin as basis, we designed such tests as the bond strength, shearing strength, tear strength, fatigue performance and aggregate polished value, and included the freeze-thaw cycle and de-icing salt and other factors in the experiment, connecting with the climate characteristics of circumpolar latitude and low altitude in Heilongjiang province. Through the pavement performance test, it is confirmed that the colored thin anti-skidding layers can adapt to cold and humid climate conditions, and its physical mechanical properties are good.

Cotransport of microorganisms and metallic colloids in quartz sand or iron oxide-coated sand under real site hydrogeological conditions

NASA Astrophysics Data System (ADS)

Yu, Tong; Wen, Yujuan; Yang, Xinyao; Yang, Yuesuo

2017-04-01

The need for studying the fate and transport of engineered and naturally-occurring nanoparticles is of great concern in the past decade. Wudalianchi scenic spot as a famous International Geological Park has the biggest cold spring in China, which is also one of the three biggest cold spring in the world, with a history of over 200 years using in drinking and medical purpose. Thousands of tourists all over the world travelling here each year to enjoy the high quality mineral water and take a bath in the cold spring and "mud-bath" with special medication purposes. Recreation activities gave rise to the engineered nanomaterials (ENMs) releasing into the water environment and increase the risk of contamination. Therefore, it is necessary to evaluate the effect of ENMs-exposure in natural environment and how it influences the transport of microorganisms of Wudalianchi in/without the presence of natural colloids (humic acid) under a series of ion strength. A thorough critical literature review of both work in the study site and the bio/nano-particle transport in porous media was a kick-off of the study. With support of the site investigations and sampling of groundwater, surface water and surface mud/soils, further numerical modelling of the hydrogeochemical speciation of the groundwater was carried out, indicating comprehensive water-rock interactions of this particular region. Metallic nanoparticles (MNPs), including metals, metal oxides and other metal-containing nanoparticles, are produced and ubiquitously applied to medical, cosmetic, photonics and catalysis industries, etc. TiO2, a widely used raw material for cosmetic industries (e.g., sunscreens), was used in this study to represent MNPs. The microorganisms used in this study were extracted from the soil in Wudalianchi. Humic acid (HA), a key component of dissolved organic matter (DOM) chosen as the natural colloids in this study, are ubiquitous and significant constituents in soils and water environment that plays an important part in many soil and water processes. The column experiments were carried out using homogeneously charged (quartz sand) and heterogeneously charged (iron oxide-coated sand) porous media. References: Yang, X., Zhang, Y., Chen, F., & Yang, Y. (2015). Interplay of natural organic matter with flow rate and particle size on colloid transport: Experimentation, visualization, and modeling. Environmental science & technology, 49(22), 13385-13393. Yang, X., Yin, Z., Chen, F., Hu, J., & Yang, Y. (2015). Organic matter induced mobilization of polymer-coated silver nanoparticles from water-saturated sand. Science of the Total Environment, 529, 182-190. Wen, Y. J., Yang, Y. S., Ren, H. J., Du, X. Q., Yang, X. Y., Zhang, L. Y., & Wang, X. S. (2015). Chemical-biological hybrid reactive zones and their impact on biodiversity of remediation of the nitrobenzene and aniline contaminated groundwater. Chemical Engineering Journal, 280, 233-240.

Mesoproterozoic graphite deposits, New Jersey Highlands: Geologic and stable isotopic evidence for possible algal origins

USGS Publications Warehouse

Volkert, R.A.

2000-01-01

Graphite deposits of Mesoproterozoic age are locally abundant in the eastern New Jersey Highlands, where they are hosted by sulphidic biotite-quartz-feldspar gneiss, metaquartzite, and anatectic pegmatite. Gneiss and metaquartzite represent a shallow marine shelf sequence of locally organic-rich sand and mud. Graphite from massive deposits within metaquartzite yielded ??13C values of -26 ?? 2??? (1??), and graphite from massive deposits within biotite-quartz-feldspar gneiss yielded ??13C values of -23 ??4???. Disseminated graphite from biotite-quartz-feldspar gneiss country rock was -22 ??3???, indistinguishable from the massive deposits hosted by the same lithology. Anatectic pegmatite is graphitic only where generated from graphite-bearing host rocks; one sample gave a ??13C value of -15???. The ??34S values of trace pyrrhotite are uniform within individual deposits, but vary from 0 to 9??? from one deposit to another. Apart from pegmatitic occurrences, evidence is lacking for long-range mobilization of carbon during Grenvillian orogenesis or post-Grenvillian tectonism. The field, petrographic, and isotope data suggest that massive graphite was formed by granulite-facies metamorphism of Proterozoic accumulations of sedimentary organic matter, possibly algal mats. Preservation of these accumulations in the sedimentary environment requires anoxic basin waters or rapid burial. Anoxia would also favour the accumulation of dissolved ferrous iron in basin waters, which may explain some of the metasediment-hosted massive magnetite deposits in the New Jersey Highlands. ?? 2000 NRC.

Testing hypotheses for the use of Icelandic volcanic ashes as low cost, natural fertilizers

NASA Astrophysics Data System (ADS)

Seward, W.; Edwards, B.

2012-04-01

Andisols are soils derived from tephra/volcanic bedrock and are generally considered to be fertile for plant growth (cf. University of Hawaii at Manoa, CTAHR). However, few studies have been published examining the immediate effects of the addition of volcanic ash to soils immediately after an eruption. Our research is motivated by unpublished accounts from Icelandic farmers that the growing season following the 2010 Eyjafjallajökull eruption ended with unusually high yields in areas that were covered by ash from the eruption early in the spring. To test the hypothesis that addition of volcanic ash to soil would have no immediate effect on plant growth, we conducted a ~6 week growth experiment in at controlled environment at the Dickinson College Farm. The experiment used relatively fast growing grain seeds as a test crop, controlled watering, known quantities of peat as an organic base, and the following general experimental design: peat was mixed in known but systematically differing proportions with 1) commercial quartz sand, 2) basaltic ash from the 2004 Grimsvötn eruption, and 3) trachyandesite ash from the 2010 Eyjafjallajökull eruption. For all experiments, the seeds growing in the simulated soil created with the two different composition volcanic ash had higher germination rates, higher growth rates, and produced plants that were healthier in appearance than the soil made from peat mixed with quartz sand. Some differences were also noted between the germination and grow rates between the basaltic and trachyandesitic ash experiments as well. Working hypotheses to explain these results include (1) shard shapes and vesicles from volcanic ash provide better water retention than quartz, allowing water to be stored longer and increasing average soil moisture, and (2) chemical nutrients from the ash facilitate germination and growth of plants. Documenting the potential benefits of fresh volcanic ash as a fertilizer is important as use of fresh ash fertlizer could lower the cost of raising crops in countries disrupted by explosive volcanic eruptions and turn a short-term negative associated with volcanic eruptions (ash fall) into a societal benefit (local source of inexpensive fertilizer). However, long term studies are also important to document how changes to ash during pedogenesis might affect long term soil structure and fertility.

Synthesis and photoluminescence of ultra-pure germanium nanoparticles

NASA Astrophysics Data System (ADS)

Chivas, R.; Yerci, S.; Li, R.; Dal Negro, L.; Morse, T. F.

2011-09-01

We have used aerosol deposition to synthesize defect and micro-strain free, ultra-pure germanium nanoparticles. Transmission electron microscopy images show a core-shell configuration with highly crystalline core material. Powder X-ray diffraction measurements verify the presence of highly pure, nano-scale germanium with average crystallite size of 30 nm and micro-strain of 0.058%. X-ray photoelectron spectroscopy demonstrates that GeO x ( x ⩽ 2) shells cover the surfaces of the nanoparticles. Under optical excitation, these nanoparticles exhibit two separate emission bands at room temperature: a visible emission at 500 nm with 0.5-1 ns decay times and an intense near-infrared emission at 1575 nm with up to ˜20 μs lifetime.

Cleaning Genesis Solar Wind Collectors with Ultrapure Water: Residual Contaminant Particle Analysis

NASA Technical Reports Server (NTRS)

Allton, J. H.; Wentworth, S. J.; Rodriquez, M. C.; Calaway, M. J.

2008-01-01

Additional experience has been gained in removing contaminant particles from the surface of Genesis solar wind collectors fragments by using megasonically activated ultrapure water (UPW)[1]. The curatorial facility has cleaned six of the eight array collector material types to date: silicon (Si), sapphire (SAP), silicon-on-sapphire (SOS), diamond-like carbon-on-silicon (DOS), gold-on-sapphire (AuOS), and germanium (Ge). Here we make estimates of cleaning effectiveness using image analysis of particle size distributions and an SEM/EDS reconnaissance of particle chemistry on the surface of UPW-cleaned silicon fragments (Fig. 1). Other particle removal techniques are reported by [2] and initial assessment of molecular film removal is reported by [3].

Single-Grain OSL Dating of Early Middle Palaeolithic Deposits at Cuesta de la Bajada, Ebro Basin, Spain

NASA Astrophysics Data System (ADS)

Arnold, L. J.; Demuro, M.; Santonja, M.; Perez-Gonzalez, A.

2012-12-01

The open-air site of Cuesta de la Bajada comprises a 2-2.5 m-thick sequence of fluvial-lacustrine sediments inset into the +50-60 m terrace deposits preserved along the south-eastern margins of the Alfambra river valley, Teruel, Spain. The main archaeological horizons lie ~20 m above the present-day river level and consists of an upward-fining sequence of massive fluvial silts and fine sands with dispersed gravels, detritic marls and shales that collectively overlie a series of planar bedded fluvial gravels. These units have yielded ~3000 lithic artefacts displaying reduction techniques characteristic of an early Middle Palaeolithic techno-complex, as well as a multitude of faunal remains indicative of a late Middle Pleistocene origin. The paucity of open-air Palaeolithic sites in the interior eastern sector of the Iberian Peninsula, and the relatively low number of documented early Middle Palaeolithic archives in this region, means that Cuesta de la Bajada is of key importance for understanding the coexistence/transition of Iberian Acheulean and Mousterian techno-complexes during the Middle Pleistocene period. Establishing reliable absolute chronologies at Cuesta de la Bajada remains essential for understanding the regional significance of this site. In an attempt to redress the existing chronological uncertainty we are undertaking an interdisciplinary dating study of the Middle Palaeolithic deposits using OSL dating, ESR/U-series dating of teeth and ESR dating of sedimentary quartz. Here we present results obtained using quartz single-grain OSL dating of 4 samples collected from a 7 m vertical profile bracketing the archaeological horizons. 2 samples were collected from the archaeology-bearing silt and fine sand horizons, while the remaining samples were obtained from well-bedded fine-sands and silts 3.5 m above and 3 m below the main excavation. The measured quartz grains are characterised by relatively bright OSL signals and typically display dose-response curves with very high saturation limits. The latter offers the advantage of extending the age range over which single-grain techniques can be applied in this Middle Pleistocene context. Dose-recovery tests performed at high doses of 470 Gy yielded accurate equivalent dose (De) results with low overdispersion, providing reasonable confidence in the chosen measurement conditions. 3 of the samples display single-grain De distributions with low levels of dispersion indicating that the sediments were adequately bleached prior to burial and remained undisturbed thereafter. The fourth sample displays higher De dispersion and a younger subpopulation of grains, which could be explained by beta-dose heterogeneity associated with interspersed gravels within the basal archaeological horizon. We apply various statistical age models to derive final chronologies and compare the resultant single-grain ages with those obtained using different absolute dating methods. We also report on experiments performed using 'synthetic multi-grain aliquots' created from the single-grain De datasets, and discuss their implications for the reliability of multi-grain OSL dating techniques in this context.

Single-grain OSL dating of Early Middle Palaeolithic deposits at Cuesta de la Bajada, Ebro Basin, Spain

NASA Astrophysics Data System (ADS)

Arnold, Lee; Demuro, Martina; Santonja, Manuel; Perez-Gonzalez, Alfredo; Pares, Josep

2013-04-01

The open-air site of Cuesta de la Bajada comprises a 2-2.5 m-thick sequence of fluvial-lacustrine sediments inset into the +50-60 m terrace deposits preserved along the south-eastern margins of the Alfambra river valley, Teruel, Spain. The main archaeological horizons lie ~20 m above the present-day river level and consists of an upward-fining sequence of massive fluvial silts and fine sands with dispersed gravels, detritic marls and shales that collectively overlie a series of planar bedded fluvial gravels. These units have yielded ~3000 lithic artefacts displaying reduction techniques characteristic of an early Middle Palaeolithic techno-complex, as well as a multitude of faunal remains indicative of a late Middle Pleistocene origin. The paucity of open-air Palaeolithic sites in the interior eastern sector of the Iberian Peninsula, and the relatively low number of documented early Middle Palaeolithic archives in this region, means that Cuesta de la Bajada is of key importance for understanding the coexistence/transition of Iberian Acheulean and Mousterian techno-complexes during the Middle Pleistocene period. Establishing reliable absolute chronologies at Cuesta de la Bajada remains essential for understanding the regional significance of this site. In an attempt to redress the existing chronological uncertainty we are undertaking an interdisciplinary dating study of the Middle Palaeolithic deposits using OSL dating, ESR/U-series dating of teeth and ESR dating of sedimentary quartz. Here we present results obtained using quartz single-grain OSL dating of 4 samples collected from a 7 m vertical profile bracketing the archaeological horizons. 2 samples were collected from the archaeology-bearing silt and fine sand horizons, while the remaining samples were obtained from well-bedded fine-sands and silts 3.5 m above and 3 m below the main excavation. The measured quartz grains are characterised by relatively bright OSL signals and typically display dose-response curves with very high saturation limits. The latter offers the advantage of extending the age range over which single-grain techniques can be applied in this Middle Pleistocene context. Dose-recovery tests performed at high doses of 470 Gy yielded accurate equivalent dose (De) results with low overdispersion, providing reasonable confidence in the chosen measurement conditions. Three of the samples display single-grain De distributions with low levels of dispersion indicating that the sediments were adequately bleached prior to burial and remained undisturbed thereafter. The fourth sample displays higher De dispersion and a younger subpopulation of grains, which could be explained by beta-dose heterogeneity associated with interspersed gravels within the basal archaeological horizon. We apply various statistical age models to derive final chronologies and compare the resultant single-grain ages with those obtained using different absolute dating methods. We also report on experiments performed using 'synthetic multi-grain aliquots' created from the single-grain De datasets, and discuss their implications for the reliability of multi-grain OSL dating techniques in this context.

Pore-Scale Transport of Strontium During Dynamic Water Content Changes in the Unsaturated Zone

NASA Astrophysics Data System (ADS)

Weaver, W.; Kibbey, T. C. G.; Papelis, C.

2016-12-01

Dynamic water content changes in the unsaturated zone caused by natural and manmade processes, such as evaporation, rainfall, and irrigation, have an effect on contaminant mobility. In general, in the unsaturated zone, evaporation causes an increase in contaminant concentrations, potentially leading to sorption of contaminants on aquifer materials or precipitation of crystalline or amorphous phases. On the other hand, increase of water content may result in dissolution of precipitated phases and increased mobility of contaminants. The objective of this study was to develop a quantitative model for the transport of strontium through sand under dynamic water content conditions, as a function of strontium concentration, pH, and ionic strength. Strontium was selected as a surrogate for strontium-90, a by-product of nuclear reactions. The dynamic water content was determined using an automated device for rapidly measuring the hysteretic capillary pressure—saturation relationship, followed by ambient air evaporation, and gravimetric water content measurement. Strontium concentrations were measured using inductively coupled plasma mass spectrometry (ICP-MS). Flow interruption experiments were conducted to determine whether equilibrium conditions existed for a given flowrate. Scanning electron microscopy (SEM) was used to visualize the treated quartz sand particles and the distribution of strontium on sand grains was determined using elemental maps created by energy-dispersive x-ray spectroscopy (EDX). Strontium behavior appears to be pH dependent as well as ionic strength dependent under these conditions.

Role of Grain Crushing in the Alteration of Mechanical and Flow Properties of Sandstones during Mechanical Failure

NASA Astrophysics Data System (ADS)

Mirabolghasemi, M.; Prodanovic, M.; Choens, R. C., II; Dewers, T. A.

2016-12-01

We present a workflow to study the alteration of flow and mechanical characteristics of sandstones after shear failure, specifically modeling weakening of the formation due to CO2 injection. We use discrete elements method (DEM) to represent each sand grain as a cluster of bonded sub-particles, and model their potential crushing. We also introduce bonds between sand grain clusters to enable the modeling of the mechanical behavior of consolidated sandstones. The model is tuned by comparing our numerical compression tests on single sand grains with the experimental results reported in the literature. Once the mechanical behavior of individual grains is adequately captured by the model, a packing of such grains is subjected to shear stress. Once the packing fails under the imposed shear stress, its mechanical properties, permeability, and porosity are calculated. This test is repeated for various conditions by varying parameters such as the brittleness of single grains (the relative quartz-feldspar content of the grains), normal stress, and cement strength (assuming (chemical) weakening of the inter- and intra-grain-cluster bonds due to CO2 injection). We specifically compare the effect of cement/bond strength weakening on mechanical properties to triaxial compression experimental measurements before and after hydrous scCO2 and CO2-saturated brine injection in Boise sandstone performed in Sandia National Laboratory.

Transport and retention of zinc oxide nanoparticles in porous media: effects of natural organic matter versus natural organic ligands at circumneutral pH.

PubMed

Jones, Edward H; Su, Chunming

2014-06-30

The potential toxicity of nanoparticles (NPs) has received considerable attention, but there is little knowledge relating to the fate and transport of engineered ZnO NPs in the environment. Column experiments were performed at pH 7.3-7.6 to generate effluent concentrations and retention profiles for assessing the fate and transport of ZnO NPs (PZC=9.3, nominal size 20 nm) in saturated quartz sands (256 μm) in the presence of low natural organic matter (NOM) concentrations (1 mg/L humic and fulvic acids) and millimolar natural organic ligands (NOL) levels (formic, oxalic, and citric acids). At circumneutral pHs, ZnO NPs were positively charged and immobile in sand. The presence of NOM decreased the attachment efficiency facilitating ZnO transport through sand columns. Conversely, ZnO transport in the presence of formic and oxalic acids was only slightly improved when compared to ZnO in DI water; whereas, citric acid showed no improvement. The distinct difference between NOM and NOL may have important implications with regard to ZnO transport in the subsurface environment. Experimental results suggested the presence of both favorable and unfavorable nanoparticle interactions causes significant deviations from classical colloid filtration theory (CFT). Copyright © 2014 Elsevier B.V. All rights reserved.

Influence of fillers on the alkali activated chamotte

NASA Astrophysics Data System (ADS)

Dembovska, L.; Bumanis, G.; Vitola, L.; Bajare, D.

2017-10-01

Alkali-activated materials (AAM) exhibit remarkable high-temperature resistance which makes them perspective materials for high-temperature applications, for instance as fire protecting and insulating materials in industrial furnaces. Series of experiments were carried out to develop optimum mix proportions of AAM based on chamotte with quartz sand (Q), olivine sand (OL) and firebrick sawing residues (K26) as fillers. Aluminium scrap recycling waste was considered as a pore forming agent and 6M NaOH alkali activation solution has been used. Lightweight porous AAM have been obtained with density in range from 600 to 880 kg/m3 and compressive strength from 0.8 to 2.7 MPa. The XRD and high temperature optical microscopy was used to characterize the performance of AAM. The mechanical, physical and structural properties of the AAM were determined after the exposure to elevated temperatures at 800 and 1000°C. The results indicate that most promising results for AAM were with K26 filler where strength increase was observed while Q and OL filler reduced mechanical properties due to structure deterioration caused by expansive nature of selected filler.

Efficient HOMO-LUMO separation by multiple resonance effect toward ultrapure blue thermally activated delayed fluorescence

NASA Astrophysics Data System (ADS)

Hatakeyama, Takuji; Ikuta, Toshiaki; Shiren, Kazushi; Nakajima, Kiichi; Nomura, Shintaro; Ni, Jingping

2016-09-01

Organic light-emitting diodes (OLEDs) play an important role in the new generation of flat-panel displays. Conventional OLEDs employing fluorescent materials together with triplet-triplet annihilation suffer from a relatively low internal quantum efficiency (IQE) of 62.5%. On the other hand, the IQE of OLEDs employing phosphorescent or thermally activated delayed fluorescence (TADF) materials can reach 100%. However, these materials exhibit very broad peaks with a full-width at half-maximum (FWHM) of 70-100 nm and cannot satisfy the color-purity requirements for displays. Therefore, the latest commercial OLED displays employ blue fluorescent materials with a relatively low IQE, and efficient blue emitters with a small FWHM are highly needed. In our manuscript, we present organic molecules that exhibit ultrapure blue fluorescence based on TADF. These molecules consist of three benzene rings connected by one boron and two nitrogen atoms, which establish a rigid polycyclic framework and significant localization of the highest occupied and lowest unoccupied molecular orbitals by a multiple resonance effect. An OLED device based on the new emitter exhibits ultrapure blue emission at 467 nm with an FWHM of 28 nm, Commission Internationale de l'Eclairage (CIE) coordinates of (0.12, 0.13), and an IQE of 100%, which represent record-setting performance for blue OLED devices.

Stability Characterization of Quinazoline Derivative BG1188 by Optical Methods

NASA Astrophysics Data System (ADS)

Militaru, Andra; Smarandache, Adriana; Mahamoud, Abdallah; Damian, Victor; Ganea, Paul; Alibert, Sandrine; Pagès, Jean-Marie; Pascu, Mihail-Lucian

2011-08-01

3-[2-(dimethylamino)ethyl]-6-nitroquinazolin-4(3H)-one, labeled BG1188, is a new synthesized compound, out of a series of quinazoline derivatives developed to fight the multidrug resistance of antibiotics acquired by bacteria. A characterization of the BG1188 powder was made using FTIR spectra in order to evidence the functional groups in the medicine's molecule. The ultraviolet-visible (UV-Vis) absorption spectra were used to study the stability of the BG1188 solutions in two solvents and at different temperatures. BG1188 concentration in ultrapure water was varied between 2×10-3 M (stock solution) and 10-6 M. The concentration recommended by higher activity on bacteria was 10-3 M. For the same reason, this was the utilized concentration of BG1188 in dimethyl sulfoxide (DMSO). Time stability was characterized by comparing the time evolution of the UV-Vis absorption spectra of the BG1188 solutions in ultrapure de-ionized water or in DMSO. The spectra were recorded daily for about 4 months after the preparation for the BG1188 solutions in ultrapure water. Generally, samples are stable within the experimental errors at concentrations higher than 10-5 M, but the stability time interval may vary from 119 days at 10-4 M to 34 days at 10-5 M. Time evolution of the absorption spectra at 10-3 M in ultrapure water shows reproducibility within the measuring errors (±1.045%) for time intervals up to 1032 hours (more than 40 days) after preparation. On the other hand, BG1188 solutions in DMSO may be considered unstable because the absorption spectra modify in terms of peak shapes and intensities, indicating that the samples exhibit modifications immediately after preparation. Regardless the solvent used, some aggregation phenomena took place and wire-like aggregates were observed in all the solutions with the naked eye. These aggregates were analyzed, tentatively, using optical microscopy and FTIR.

The jammed-to-mobile transition in frozen sand under stress

NASA Astrophysics Data System (ADS)

Durham, W. B.; Pathare, A.; Stern, L. A.; Lenferink, H. J.

2009-12-01

We conducted laboratory deformation experiments on sand-rich mixtures of sand + ice under sufficient confinement to inhibit macroscopic dilation. Dry sand packs constrained not to dilate when they are under a shearing load reach an immobile or “jammed” state, as load-supporting “force chains” of sand particles form after a small amount of strain and cannot be broken without volume expansion. Our research objective here was to find the minimum volume fraction of ice required to overcome the jammed state. The result surprised us: the required volume fraction is not a fixed number, but depends on the packing characteristics of the sand in question. Experiments were carried out in a triaxial gas deformation rig at confining pressures (60 - 200 MPa) always at least twice the level of differential stresses (11 - 50 MPa) in order to suppress dilatancy. Run temperatures were 223 - 243 K. We used two kinds of quartz sand, one well-sorted, with a maximum dry packing density (MDPD) of about 0.68 sand by volume, and the other a mixture of two sizes, having a higher MDPD of 0.75. Ice volume fraction ranged from well below saturation (where unfilled porosity necessarily remained) to slightly greater than the value of porosity at MDPD. We tested these frozen sands in compression under constant applied differential stress (creep). Strain rates were very low at these conditions, and runs took days or weeks to complete. The amount of strain required to reach the jammed state in ice-undersaturated samples was approximately 0.04, and did not show an obvious dependence on ice content. For both sands, the onset of mobility occurred at approximately 5% above the value of pore volume at MDPD. Furthermore, viscosity of mobile frozen sand near the transition point was extremely sensitive to ice fraction, which implies that at geologic strain rates, far slower than we can reach in the lab, the ice fraction at transition may lie closer to that at MDPD. Cryogenic scanning electron microscopy shows that fracturing of sand grains occurs in ice-undersaturated samples, but gradually disappears as saturation is reached. There are no fractured sand grains in deforming mobile frozen sand packs. One application of this work is to the regolith of Mars at mid-latitudes and poleward, where significant ice is expected to be present. Partially relaxed (“softened”) landforms such as craters require the presence of ice, but also suggest strengths far higher than that of ice. The extreme sensitivity of viscosity to ice content near the mobility boundary, and the near coincidence of mobility and saturation at MDPD together suggest a plausible explanation for partial landform softening on Mars that does not require a fortuitous ice content or an unrealistically brief period of saturation; namely, that the water content of the Martian regolith lies at or near saturation. If true, we can estimate the historical water content of the Martian regolith for reasonable soil densities as being between 120 and 240 global meters of water for the upper kilometer of crust. This is somewhat lower than previous estimates.

Microbial mineral colonization across a subsurface redox transition zone

DOE PAGES

Converse, Brandon J.; McKinley, James P.; Resch, Charles T.; ...

2015-08-28

Here our study employed 16S rRNA gene amplicon pyrosequencing to examine the hypothesis that chemolithotrophic Fe(II)-oxidizing bacteria (FeOB) would preferentially colonize the Fe(II)-bearing mineral biotite compared to quartz sand when the minerals were incubated in situ within a subsurface redox transition zone (RTZ) at the Hanford 300 Area site in Richland, WA, USA. The work was motivated by the recently documented presence of neutral-pH chemolithotrophic FeOB capable of oxidizing structural Fe(II) in primary silicate and secondary phyllosilicate minerals in 300 Area sediments and groundwater (Benzine et al., 2013). Sterilized portions of sand+biotite or sand alone were incubated in situ formore » 5 months within a multilevel sampling (MLS) apparatus that spanned a ca. 2-m interval across the RTZ in two separate groundwater wells. Parallel MLS measurements of aqueous geochemical species were performed prior to deployment of the minerals. Contrary to expectations, the 16S rRNA gene libraries showed no significant difference in microbial communities that colonized the sand+biotite vs. sand-only deployments. Both mineral-associated and groundwater communities were dominated by heterotrophic taxa, with organisms from the Pseudomonadaceae accounting for up to 70% of all reads from the colonized minerals. These results are consistent with previous results indicating the capacity for heterotrophic metabolism (including anaerobic metabolism below the RTZ) as well as the predominance of heterotrophic taxa within 300 Area sediments and groundwater. Although heterotrophic organisms clearly dominated the colonized minerals, several putative lithotrophic (NH 4 +, H 2, Fe(II), and HS - oxidizing) taxa were detected in significant abundance above and within the RTZ. Such organisms may play a role in the coupling of anaerobic microbial metabolism to oxidative pathways with attendant impacts on elemental cycling and redox-sensitive contaminant behavior in the vicinity of the RTZ.« less

Testing the ISP method with the PARIO device: Accuracy of results and influence of homogenization technique

NASA Astrophysics Data System (ADS)

Durner, Wolfgang; Huber, Magdalena; Yangxu, Li; Steins, Andi; Pertassek, Thomas; Göttlein, Axel; Iden, Sascha C.; von Unold, Georg

2017-04-01

The particle-size distribution (PSD) is one of the main properties of soils. To determine the proportions of the fine fractions silt and clay, sedimentation experiments are used. Most common are the Pipette and Hydrometer method. Both need manual sampling at specific times. Both are thus time-demanding and rely on experienced operators. Durner et al. (Durner, W., S.C. Iden, and G. von Unold (2017): The integral suspension pressure method (ISP) for precise particle-size analysis by gravitational sedimentation, Water Resources Research, doi:10.1002/2016WR019830) recently developed the integral suspension method (ISP) method, which is implemented in the METER Group device PARIOTM. This new method estimates continuous PSD's from sedimentation experiments by recording the temporal evolution of the suspension pressure at a certain measurement depth in a sedimentation cylinder. It requires no manual interaction after start and thus no specialized training of the lab personnel. The aim of this study was to test the precision and accuracy of new method with a variety of materials, to answer the following research questions: (1) Are the results obtained by PARIO reliable and stable? (2) Are the results affected by the initial mixing technique to homogenize the suspension, or by the presence of sand in the experiment? (3) Are the results identical to the one that are obtained with the Pipette method as reference method? The experiments were performed with a pure quartz silt material and four real soil materials. PARIO measurements were done repetitively on the same samples in a temperature-controlled lab to characterize the repeatability of the measurements. Subsequently, the samples were investigated by the pipette method to validate the results. We found that the statistical error for silt fraction from replicate and repetitive measurements was in the range of 1% for the quartz material to 3% for soil materials. Since the sand fractions, as in any sedimentation method, must be measured explicitly and are used as fixed parameters in the PARIO evaluation, the error of the clay fraction is determined by error propagation from the sand and silt fraction. Homogenization of the suspension by overhead shaking gave lower reproducibility and smaller silt fractions than vertical stirring. However, it turned out that vertical stirring must be performed with sufficient rigour to obtain a fully homogeneous initial distribution. Analysis of material sieved to < 2000 μm and to < 200 μm gave equal results, i.e., there was no hint towards dragging effects of large particles. Complete removal of the sand fraction, i.e. sieving to < 63 μm lead to less silt, probably due to a loss of fine material by the sieving process. The PSD's obtained with the PARIO corresponded very well with the results of the Pipette method.

Biochemical distributions (amino acids, neutral sugars, and lignin phenols) among size-classes of modern marine sediments from the Washington coast

NASA Astrophysics Data System (ADS)

Keil, Richard G.; Tsamakis, Elizabeth; Giddings, J. Calvin; Hedges, John I.

1998-04-01

In order to examine relationships of organic matter source, composition, and diagenesis with particle size and mineralogy in modern marine depositional regimes, sediments from the continental shelf and slope along the Northwest Pacific rim (Washington coast, USA) were sorted into hydrodynamic size fractions (sand: >250, 63-250 μm; silt: 35-63, 17-35, 8-17, 3-8 μm; and clay-sized: 1-3, 0.5-1, <0.5 μm). The size fractions were then density fractionated to separate distinct organic debris from mineral-associated organic matter, and the various separates were analyzed for their amino acid, aldose, and lignin compositions. The composition of organic matter in the separates changes markedly as a function of particle size and density. Large compositional differences were observed between the clay-sized fractions (dominated mineralogically by smectites), the sand-sized mineral-associated isolates (quartz-rich), and floated coarse organic matter (dominated by vascular plant debris). Organic matter intimately associated with the clay-sized fractions shows the most extensive diagenetic alteration, as reflected in high abundances of nonprotein amino acids (especially β-alanine), elevated lignin phenol acid/aldehyde ratios, and high relative concentrations of the deoxyhexoses fucose and rhamnose. Organic matter in the silt fractions, though degraded, is not as diagenetically altered as in the clay fractions. Enrichment of pollen grains in the silt-size material is reflected by high cinnamic acid to ferulic acid lignin phenol ratios. The highest pollen biochemical signal is observed in the silt fractions of the deepest station (1835 m), where pollen abundances are also highest. Organic matter tightly bound in the silt and sand-sized fractions are enriched in aldoses and show indications of enhanced microbial biomass as reflected by high weight percentages of ribose. Distinct organic debris was composed of relatively unaltered vascular plant remains as reflected by high lignin phenol yields and low acid/aldehyde ratios. Clay-size fractions are enriched in nitrogenous components, as reflected by elevated yields of total and basic amino acids (especially lysine). Silt- and sand-size fractions rich in quartz and albite show slightly higher yields of neutral amino acids. Consistent trends across all size classes and among the different depositional settings illustrates that only a small portion of the organic matter is present as distinct organic debris (e.g. pollen, vascular plant tissues, etc.), but that this debris can be isolated in specific size classes. The data for surface-associated organic matter are consistent with, but not conclusive of, selective partitioning of some organic matter to specific mineral surfaces. The dominant size class-specific trends in organic matter composition are due to changes in both source and diagenetic alteration.

Impact of matric potential and pore size distribution on growth dynamics of filamentous and non-filamentous soil bacteria.

PubMed

Wolf, Alexandra B; Vos, Michiel; de Boer, Wietse; Kowalchuk, George A

2013-01-01

The filamentous growth form is an important strategy for soil microbes to bridge air-filled pores in unsaturated soils. In particular, fungi perform better than bacteria in soils during drought, a property that has been ascribed to the hyphal growth form of fungi. However, it is unknown if, and to what extent, filamentous bacteria may also display similar advantages over non-filamentous bacteria in soils with low hydraulic connectivity. In addition to allowing for microbial interactions and competition across connected micro-sites, water films also facilitate the motility of non-filamentous bacteria. To examine these issues, we constructed and characterized a series of quartz sand microcosms differing in matric potential and pore size distribution and, consequently, in connection of micro-habitats via water films. Our sand microcosms were used to examine the individual and competitive responses of a filamentous bacterium (Streptomyces atratus) and a motile rod-shaped bacterium (Bacillus weihenstephanensis) to differences in pore sizes and matric potential. The Bacillus strain had an initial advantage in all sand microcosms, which could be attributed to its faster growth rate. At later stages of the incubation, Streptomyces became dominant in microcosms with low connectivity (coarse pores and dry conditions). These data, combined with information on bacterial motility (expansion potential) across a range of pore-size and moisture conditions, suggest that, like their much larger fungal counterparts, filamentous bacteria also use this growth form to facilitate growth and expansion under conditions of low hydraulic conductivity. The sand microcosm system developed and used in this study allowed for precise manipulation of hydraulic properties and pore size distribution, thereby providing a useful approach for future examinations of how these properties influence the composition, diversity and function of soil-borne microbial communities.

The Utility of Using a Near-Infrared (NIR) Camera to Measure Beach Surface Moisture

NASA Astrophysics Data System (ADS)

Nelson, S.; Schmutz, P. P.

2017-12-01

Surface moisture content is an important factor that must be considered when studying aeolian sediment transport in a beach environment. A few different instruments and procedures are available for measuring surface moisture content (i.e. moisture probes, LiDAR, and gravimetric moisture data from surface scrapings); however, these methods can be inaccurate, costly, and inapplicable, particularly in the field. Near-infrared (NIR) spectral band imagery is another technique used to obtain moisture data. NIR imagery has been predominately used through remote sensing and has yet to be used for ground-based measurements. Dry sand reflects infrared radiation given off by the sun and wet sand absorbs IR radiation. All things considered, this study assesses the utility of measuring surface moisture content of beach sand with a modified NIR camera. A traditional point and shoot digital camera was internally modified with the placement of a visible light-blocking filter. Images were taken of three different types of beach sand at controlled moisture content values, with sunlight as the source of infrared radiation. A technique was established through trial and error by comparing resultant histogram values using Adobe Photoshop with the various moisture conditions. The resultant IR absorption histogram values were calibrated to actual gravimetric moisture content from surface scrapings of the samples. Overall, the results illustrate that the NIR spectrum modified camera does not provide the ability to adequately measure beach surface moisture content. However, there were noted differences in IR absorption histogram values among the different sediment types. Sediment with darker quartz mineralogy provided larger variations in histogram values, but the technique is not sensitive enough to accurately represent low moisture percentages, which are of most importance when studying aeolian sediment transport.

Mixing of biogenic siliceous and terrigenous clastic sediments: South Belridge field and Beta field, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schwartz, D.E.

1990-05-01

The intermixing and interbedding of biogenically derived siliceous sediment with terrigenous clastic sediment in reservoirs of upper Miocene age provides both reservoir rock and seal and influences productivity by affecting porosity and permeability. Miocene reservoirs commonly contain either biogenic-dominated cyclic diatomite, porcelanite, or chert (classic Monterey Formation) or clastic-dominated submarine fan sequences with interbedded or intermixed siliceous members of biogenic origin. Biogenic-clastic cycles, 30-180 ft thick, at South Belridge field were formed by episodic influx of clastic sediment from distant submarine fans mixing with slowly accumulating diatomaceous ooze. The cycles consist of basal silt and pelletized massive diatomaceous mudstone, overlainmore » by burrowed, faintly bedded clayey diatomite and topped by laminated diatomite. Cycle tops have higher porosity and permeability, lower grain density, and higher oil saturation than clay and silt-rich portions of the cycles. Submarine fan sediments forming reservoirs at the Beta field are comprised of interbedded sands and silts deposited in a channelized middle fan to outer fan setting. Individual turbidites display fining-upward sequences, with oil-bearing sands capped by wet micaceous silts. Average sands are moderately to poorly sorted, fine- to medium-grained arkosic arenites. Sands contain pore-filling carbonate and porcelaneous cements. Porcelaneous cement consists of a mixture of opal-A, opal-CT, and chert with montmorillonite and minor zeolite. This cement is an authigenic material precipitated in intergranular pore space. The origin of the opal is biogenic, with recrystallization of diatom frustules (opal-A) into opal-CT lepispheres and quartz crystals. Porcelaneous cement comprises 4-21% of the bulk volume of the rock. Seventy percent of the bulk volume of the cement is micropore space.« less

Sedimentary sulfides in dune sands of Spiekeroog Island, southern North Sea: A biogeochemical study of sulfur isotope partitioning

NASA Astrophysics Data System (ADS)

Seibert, Stephan; Schubert, Florian; Schmiedinger, Iris; Böttcher, Michael E.; Massmann, Gudrun

2017-04-01

The formation of iron sulfides in sandy sediments and the associated development of stable isotope signatures is still mechanistically not understood. In dune sands under impact of both fresh and saline water several physico-chemical gradients may develop leading to distinctly different biogeochemical zones. In the present study, a 10 m long core from a dune base at the North Eastern part of Spiekeroog Island, southern North Sea, was investigated for the elemental and stable isotope composition. The pyrite (TRIS) content was quantitatively extracted via an acidic Cr(II) distillation procedure and the stable sulfur isotope composition was determined by means of C-irmMS. The pore waters display a downcore increase in salt contents and a mixing between fresh and salt water. The accumulation of metabolites at depth indicate an increasing superimposition of mixing by microbial decomposition of dissolved organic matter with only limited net sulfate reduction. This indicates an essential open system with respect to dissolved sulfate. The sands were found to be very low in TOC, TIC, and TRIS and dominated by quartz minerals. Under the assumption that North Sea water sulfate was the only substantial sulfate source (d34S = + 21per mil), the sedimentary sulfides indicate an overall sulfur isotope discrimination upon microbial sulfate reduction between 39 and 52 per mil, which is within the range of results from other fully marine sands from the Spiekeroog area and laboratory studies with pure cultures of sulfate-reducing bacteria under low cellular sulfate reduction rates. Further investigations are on the way to understand the processes leading to the iron sulfide formation in these organic-poor substrates.

Three magnetic reversals recorded in an 80-m organic-rich core from a sinkhole east of Tampa, FL

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCartan, L.; Rubin, M.; Liddicoat, J.C.

1994-03-01

Preliminary analysis of a continuous 80-m core from a phosphate mines at Bartow, Fla., indicates as many as three magnetically reversed and five normal sections and five upward-fining depositional sequences. The paleomagnetic data are based on analysis of 16 samples; 100 additional samples have been taken for more detailed analysis. The authors estimate the maximum age to be 1.1--2.6 Ma. The core is composed of massive to faintly laminated beds of black to dark-brown, organic-rich, fine quartz sand and silt, kaolinitic and organic clay, and peat, Only the top meter is within the 40 Ka range of [sup 14]C; amore » sample at 8.5 m yielded an age estimate close to 350,000 years, the limit of the open-system U/Th dating technique. Rates of deposition are 2--7.5 cm/1,000 years, which is much slower than rates in late Quaternary lakes elsewhere in Florida. There is no clear relation between the magnetic stratigraphy and the depositional stratigraphy. The authors assume that most of the sand was derived from dissolved limestone around the sinkhole, but some of the sand as well as the silt and clay may be windborne. Textural variations may be coincident with differences in rainfall, and this concept will be investigated through pollen analysis of approximately 800 samples. The one sample examined so far is from the bottom of the core, and it has an equivocal biostratigraphic age. The high grass pollen content indicates a drier climate than at present; it is from a long interval of peat with sand, which is typically windborne in dry climates.« less

The White Nile as a source for Nile sediments: Assessment using U-Pb geochronology of detrital rutile and monazite

NASA Astrophysics Data System (ADS)

Be'eri-Shlevin, Yaron; Avigad, Dov; Gerdes, Axel

2018-04-01

Basement terranes exposed at the headwaters of the White Nile include Archean-Paleoproterozoic rocks of the Congo Craton, whose northern sectors were severely reworked during Neoproterozoic orogeny. New U-Pb analyses of detrital rutile and monazite from early Quaternary to Recent coastal quartz sands of Israel, at the northeast extension of the Nile sedimentary system, yield mostly late Neoproterozoic ages, with a dominant peak at ca. 600 Ma. While derivation from the reworked sectors of the Craton cannot be negated, the absence of pre-Neoproterozoic rutile and monazite indicates that the detrital contribution from the Congo cratonic nuclei into the main Nile was insignificant. The near absence of White Nile basement-derived heavy minerals from the Nile sands arriving at the Eastern Mediterranean may be explained by a number of factors such as relatively minor erosion of the Cratonic basement nuclei during the Quaternary, late connection of the White Nile to the main Nile system with a possibility that northern segments connected prior to more southerly ones, and a long-term effective sediment blockage mechanism at the mouth of White Nile. Likewise, our previous study demonstrated that Nile sands display a detrital zircon U-Pb-Hf pattern consistent with significant recycling of NE African Paleozoic sediments. It is thus plausible that any detrital contribution from White Nile basement rocks was thoroughly diluted by eroded Paleozoic sediments, or their recycled products, which were likely the greatest sand reservoir in the region. This study adds to previous studies showing the advantage of a multi mineral U-Pb geochronology strategy in constraining sediment provenance patterns.

Ultrapure glass optical waveguide development in microgravity by the sol-gel process

NASA Technical Reports Server (NTRS)

Mukherjee, S. P.; Holman, R. A.

1981-01-01

Multicomponent, homogeneous, noncrystalline oxide gels can be prepared by the sol-gel process and these gels are promising starting materials for melting glasses in the space environment. The sol-gel process referred to here is based on the polymerization reaction of alkoxysilane with other metal alkoxy compounds or suitable metal salts. Many of the alkoxysilanes or other metal alkoxides are liquids and thus can be purified by distillation. The use of gels offers several advantages such as high purity and lower melting times and temperatures. The sol-gel process is studied for utilization in the preparation of multicomponent ultrapure glass batches for subsequent containerless melting of the batches in space to prepare glass blanks for optical waveguides.

Ultra-pure, water-dispersed Au nanoparticles produced by femtosecond laser ablation and fragmentation

PubMed Central

Kubiliūtė, Reda; Maximova, Ksenia A; Lajevardipour, Alireza; Yong, Jiawey; Hartley, Jennifer S; Mohsin, Abu SM; Blandin, Pierre; Chon, James WM; Sentis, Marc; Stoddart, Paul R; Kabashin, Andrei; Rotomskis, Ričardas; Clayton, Andrew HA; Juodkazis, Saulius

2013-01-01

Aqueous solutions of ultra-pure gold nanoparticles have been prepared by methods of femtosecond laser ablation from a solid target and fragmentation from already formed colloids. Despite the absence of protecting ligands, the solutions could be (1) fairly stable and poly size-dispersed; or (2) very stable and monodispersed, for the two fabrication modalities, respectively. Fluorescence quenching behavior and its intricacies were revealed by fluorescence lifetime imaging microscopy in rhodamine 6G water solution. We show that surface-enhanced Raman scattering of rhodamine 6G on gold nanoparticles can be detected with high fidelity down to micromolar concentrations using the nanoparticles. Application potential of pure gold nanoparticles with polydispersed and nearly monodispersed size distributions are discussed. PMID:23888114

Luminescence and Radiocarbon dating of roman time harbour sediments from Cologne - A comparison of different methods

NASA Astrophysics Data System (ADS)

Lauer, Tobias; Frechen, Manfred; Fuchs, Magret C.; Trier, Marcus; Tsukamoto, Sumiko

2010-05-01

Optically stimulated luminescence (OSL) dating was applied to fluvial and colluvial deposits which were taken from a roman time harbour basin in Cologne. Hence, independent age control was given by roman artefacts (coins, bricks) of known age and by three radiocarbon data. For one sample (well sorted fluvial sand), a single aliquot regenerative (SAR) protocol was applied to coarse grain quartz. A large number of equivalent doses (80) were collected and after De-measurements, different statistical approaches were tested. The results show, that calculating the age by using the Mean or Median of all accepted De-values yields OSL ages of 3.5 ± 0.3 ka and 2.8 ± 0.3 ka, respectively, what would be significantly too old. The application of the Leading Edge Method (Lepper & McKeever 2002), the statistical approach after Fuchs & Lang (2001) or the Minimum Age Method (MAM3) after Galbraith et al. (1999) yield OSL age estimates of 2.0 ± 0.1 ka, 2.1 ± 0.1 ka and 1.7 ± 0.6 ka, respectively. Those ages fit very well to the 14C-ages and are in better agreement with the known archaeological background. For the colluvial sample, the quartz OSL signal was effected by feldspar impurities. For this sample, different methodological approaches were tested to see which one has the best potential to minimize the feldspar contribution. Therefore the post-IR blue stimulated quartz luminescence was recorded. The quartz signal was measured using continuous wave (CW) and pulsed OSL (POSL). For the CW measurements, it was tested if a prior IR-bleach @ 50°C or @ 225°C has better potential for minimizing the feldspar signal. In this case, an IR-bleach @ 225°C (Buylaert et al. in press) was the most effective way to obtain a higher purity of the quartz OSL signal. Buylaert, J.P., Murray, A.S., Thomsen, K.J., Jain, M.: The effect of preheating on the IRSL signal from feldspar. In press. - Radiat. Meas., special issue, LED08. Fuchs, M. & Lang, A. (2001): OSL dating of coarse-grain fluvial quartz using single-aliquot protocols on sediments from NE Peloponnese, Greece. - Quaternary Science Reviews, 20: 783-787. Galbraith, R. F., Roberts, R. G., Laslett, G. M., Yoshida, H. & Olley, J. M. (1999): Optical dating of single and multiple grains of quartz from Jinmium Rock Shelter, northern Australia: Part 1, experimental design and statistical models. - Archaeometry, 41: 339-364. Lepper, K. & McKeever, S.W.S. (2002): An objective methodology for dose distribution analysis. Radiation Protection Dosimetry. - Solid State Dosimetry, 101: 349-352.

Origin of karst conduits in calcareous sandstone and carbonate-silicate rocks: Complex role of insoluble material

NASA Astrophysics Data System (ADS)

Bruthans, Jiri; Balak, Frantisek; Schweigstillova, Jana; Vojtisek, Jan

2017-04-01

Carbonate karst is best developed in high-grade limestones and majority of the studies is focused on these rocks. Features developed by dissolution of calcite cement in quartz sandstones and dissolution of various carbonate-silicate rocks are studied far less frequently. Unlike in common karst, the insoluble residuum has to be washed out after dissolution to create high-permeability conduits in these rocks. Aquifers in a Bohemian Cretaceous Basin (BCB), the most important hydrogeological basin in the Czech Republic, consist mainly of quartz and calcareous sandstones to siltstones. These rocks are intercalated by thin layers of calcite-cemented sandstone and low-grade limestone, the latter sometimes partly impregnated by a secondary silica. Results of tracer tests show a high flow velocity in some of the aquifers. Springs with flow rate up to 500 l/s and wells with yield up to 200 l/s occur in these rocks. Dissolution features in BCB were however not yet studied in detail. For identification and characterization of rocks prone to karstification, 350 cores were sampled mostly from boreholes but also from rock outcrops in several areas of BCB. Cores were taken from intervals where: (i) high carbonate content was expected, (ii) conduits and enlarged porosity was observed in rock outcrops or wells, (iii) inflows to boreholes were determined by well logging. Calcium carbonate content was determined by calcimetry in all cores. All cores were leached in hydrochloric acid to observe the degree of disintegration after removal of calcite, which was far dominating portion of total carbonate. Polished sections were prepared from selected cores and Ca, Si, Na, K, Al content was automatically mapped by microprobe to visualize the calcium, silica, feldspar and clay mineral distribution in cores. Conduits were photo documented in the field. Two types of sediments with distinct disintegration characteristics were observed: (i) In sandstone composed of quartz grains cemented by calcite the complete disintegration occurs when calcite content exceeds 30-50%. Such calcite-rich layers are mostly few tens of cms thick and are enclosed in quartz sandstone. Groundwater flow dissolves calcite cement and turns the rock into cohesion-less sand. Sand is consequently washed out by headward erosion in drainage areas forming high capacity conduits within the sandstone. (ii) In carbonates containing secondary silica which form reinforcing structure, even 70-80% calcite content may not be sufficient for rock disintegration during leaching. Disintegration occurs only on tectonically heavily fractured zones, where secondary silica structure is fragmented. It was found that inflows into wells are often associated with zones prone to karstification. Results clearly show that form of insoluble material is critical for karstification potential. Insoluble grain size defines minimum flow velocity needed to excavate the conduits in dissolved residuum. Impregnation by secondary silica needs to be tectonically fragmented prior conduits can occur. Research was funded by the Czech Science Foundation (GA CR No. 16-19459S) and Review of groundwater resources (Ident. No. 155996).

Treatment of groundwater containing Mn(II), Fe(II), As(III) and Sb(III) by bioaugmented quartz-sand filters.

PubMed

Bai, Yaohui; Chang, Yangyang; Liang, Jinsong; Chen, Chen; Qu, Jiuhui

2016-12-01

High concentrations of iron (Fe(II)) and manganese (Mn(II)) often occur simultaneously in groundwater. Previously, we demonstrated that Fe(II) and Mn(II) could be oxidized to biogenic Fe-Mn oxides (BFMO) via aeration and microbial oxidation, and the formed BFMO could further oxidize and adsorb other pollutants (e.g., arsenic (As(III)) and antimony (Sb(III))). To apply this finding to groundwater remediation, we established four quartz-sand columns for treating groundwater containing Fe(II), Mn(II), As(III), and Sb(III). A Mn-oxidizing bacterium (Pseudomonas sp. QJX-1) was inoculated into two parallel bioaugmented columns. Long-term treatment (120 d) showed that bioaugmentation accelerated the formation of Fe-Mn oxides, resulting in an increase in As and Sb removal. The bioaugmented columns also exhibited higher overall treatment effect and anti-shock load capacity than that of the non-bioaugmented columns. To clarify the causal relationship between the microbial community and treatment effect, we compared the biomass of active bacteria (reverse-transcribed real-time PCR), bacterial community composition (Miseq 16S rRNA sequencing) and community function (metagenomic sequencing) between the bioaugmented and non-bioaugmented columns. Results indicated that the QJX1 strain grew steadily and attached onto the filter material surface in the bioaugmented columns. In general, the inoculated strain did not significantly alter the composition of the indigenous bacterial community, but did improve the relative abundances of xenobiotic metabolism genes and Mn oxidation gene. Thus, bioaugmentation intensified microbial degradation/utilization for the direct removal of pollutants and increased the formation of Fe-Mn oxides for the indirect removal of pollutants. Our study provides an alternative method for the treatment of groundwater containing high Fe(II), Mn(II) and As/Sb. Copyright © 2016 Elsevier Ltd. All rights reserved.

Natural radioactivity in, and inorganic chemistry of, ground water in the Kirkwood-Cohansey aquifer system, southern New Jersey, 1983-89

USGS Publications Warehouse

Kozinski, Jane; Szabo, Zoltan; Zapecza, O.S.; Barringer, T.H.

1995-01-01

The distribution of naturally occurring radionuclides in ground water of the Kirkwood- Cohansey aquifer system in southern New Jersey was assessed during 1988-89. The Kirkwood-Cohansey aquifer system consists of quartz-sand formations overlain by a feldspar-rich quartz-sand formation, the Bridgeton Formation, that is heavily developed agriculturally. The sum of the concentrations of radium-226 and radium-228 exceeded the U.S. Environmental Protection Agency maximum contaminant level (MCL) of 5 pCi/L (picocuries per liter) in 26 of 81 wells from which water samples were analyzed, and gross alpha-particle activity exceeded the MCL of 15 pCi/L in 5 of the 81 samples. The median concentrations of radon-222 and uranium were 280 pCi/L and 0.03 micrograms per liter, respectively. Water in the Kirkwood-Cohansey aquifer system generally is dilute (median dissolved solids concentration, 55 milligrams per liter) and acidic (median pH, 4.90), but concentrations of major ions and acidity are higher in water from wells in areas where the Bridgeton Formation outcrop and agricultural land use are present than in areas where they are absent. Concentrations and activities of radionuclides also were greatest in these areas. Results of statistical analyses indicate that these relations are significant and nonrandom. The positive relation of radionuclide concentration or activity to the presence of geologic outcrop and agricultural land, and a similar relation of the concentration of inorganic constituents to the presence of geologic outcrop and agricultural land, indicate that geochemical processes enhance mobilization of radionuclides in these areas relative to areas where the Bridgeton Formation and agricultural land are absent. The sum of the ocncentrations of radium-226 and radium-228 most likely exceeds the MCL in ground-water samples with nitrate concentrations greater than 5 milligrams per liter.

Mineral and energy resources of the BLM Roswell Resource Area, east-central New Mexico

USGS Publications Warehouse

Bartsch-Winkler, Susan B.

1992-01-01

The sedimentary formations of the Roswell Resource Area have significant mineral and energy resources. Some of the pre-Pennsylvanian sequences in the Northwestern Shelf of the Permian Basin are oil and gas reservoirs, and Pennsylvanian rocks in Tucumcari basin are reservoirs of oil and gas as well as source rocks for oil and gas in Triassic rocks. Pre-Permian rocks also contain minor deposits of uranium and vanadium, limestone, and associated gases. Hydrocarbon reservoirs in Permian rocks include associated gases such as carbon dioxide, helium, and nitrogen. Permian rocks are mineralized adjacent to the Lincoln County porphyry belt, and include deposits of copper, uranium, manganese, iron, polymetallic veins, and Mississippi-valley-type (MVT) lead-zinc. Industrial minerals in Permian rocks include fluorite, barite, potash, halite, polyhalite, gypsum, anhydrite, sulfur, limestone, dolomite, brine deposits (iodine and bromine), aggregate (sand), and dimension stone. Doubly terminated quartz crystals, called "Pecos diamonds" and collected as mineral specimens, occur in Permian rocks along the Pecos River. Mesozoic sedimentary rocks are hosts for copper, uranium, and small quantities of gold-silver-tellurium veins, as well as significant deposits of oil and gas, COa, asphalt, coal, and dimension stone. Mesozoic rocks contain limited amounts of limestone, gypsum, petrified wood, dinosaur remains, and clays. Tertiary rocks host ore deposits commonly associated with intrusive rocks, including platinum group elements, iron skarns, manganese, uranium and vanadium, molybdenum, polymetallic vein deposits, gold-silver- tellurium veins, and thorium-rare earth veins. Museum-quality quartz crystals in Lincoln County were formed in association with intrusive rocks in the Lincoln County porphyry belt. Industrial minerals in Tertiary rocks include fluorite, vein- and bedded-barite, caliche, limestone, and aggregate. Tertiary and Quaternary sediments host important placer deposits of gold and titanium, and minor silver, uranium occurrences, as well as important industrial commodities, including caliche, limestone and dolomite, and aggregate (sand). Quaternary basalt contains sub-ore-grade uranium, scoria, and clay deposits.

Lower Cretaceous smarl turbidites of the Argo Abyssal Plain, Indian Ocean

USGS Publications Warehouse

Dumoulin, Julie A.; Stewart, Sondra K.; Kennett, Diana; Mazzullo, Elsa K.

1992-01-01

Sediments recovered during Ocean Drilling Program (ODP) Leg 123 from the Argo Abyssal Plain (AAP) consist largely of turbidites derived from the adjacent Australian continental margin. The oldest abundant turbidites are Valanginian-Aptian in age and have a mixed (smarl) composition; they contain subequal amounts of calcareous and siliceous biogenic components, as well as clay and lesser quartz. Most are thin-bedded, fine sand to mud-sized, and best described by Stow and Piper's model (1984) for fine-grained biogenic turbidites. Thicker (to 3 m), coarser-grained (medium-to-coarse sand-sized) turbidites fit Bouma's model (1962) for sandy turbidites; these generally are base-cut-out (BCDE, BDE) sequences, with B-division parallel lamination as the dominant structure. Parallel laminae most commonly concentrate quartz and/or calcispheres vs. lithic clasts or clay, but distinctive millimeter to centimeter-thick, radiolarian-rich laminae occur in both fine and coarse-grained Valanginian-Hauterivian turbidites.AAP turbidites were derived from relatively deep parts of the continental margin (outer shelf, slope, or rise) that lay below the photic zone, but above the calcite compensation depth (CCD). Biogenic components are largely pelagic (calcispheres, foraminifers, radiolarians, nannofossils); lesser benthic foraminifers are characteristic of deep-water (abyssal to bathyal) environments. Abundant nonbiogenic components are mostly clay and clay clasts; smectite is the dominant clay species, and indicates a volcanogenic provenance, most likely the Triassic-Jurassic volcanic suite exposed along the northern Exmouth Plateau.Lower Cretaceous smarl turbidites were generated during eustatic lowstands and may have reached the abyssal plain via Swan Canyon, a submarine canyon thought to have formed during the Late Jurassic. In contrast to younger AAP turbidites, however, Lower Cretaceous turbidites are relatively fine-grained and do not contain notably older reworked fossils. Early in its history, the northwest Australian margin provided mainly contemporaneous slope sediment to the AAP; marginal basins adjacent to the continent trapped most terrigenous detritus, and pronounced canyon incisement did not occur until Late Cretaceous and, especially, Cenozoic time.

Stratigraphic analysis of the Paleocene Beaufort Formation, Lenoir and Craven Counties, North Carolina

DOE Office of Scientific and Technical Information (OSTI.GOV)

McLaurin, B.T.

The Beaufort Formation (BF) occurs in the inner coastal plain in a fault-bounded basin associated with the Graingers wrench zone. The unit disconformably overlies the Cretaceous Peedee Fm., and is overlain disconformably by either the Eocene Castle Hayne Limestone or younger units. Although the BF is only known to crop out along the western margin of the basin, approximately 36 core-holes penetrate the unit in the basin. Core-hole analysis indicates that the BF rapidly varies in thickness from 0--85 feet over a distance of several hundred feet. The BF is divided into the lower Jericho Run Member of Danian agemore » and an upper unnamed member of Thanetian age. The Jericho Run Member (JRM) is principally a light-gray to gray siliceous mudstone which in some places contains interbeds of very fine to coarse glauconitic quartz sand. The mudstone is often burrowed and can contain as much as 40% quartz and 15% glauconite usually concentrated in thin laminae or burrows. The JRM is the most widespread member of the BF obtaining a maximum thickness of 53 feet. Where present, it always lies disconformably on the Peedee Formation and is either overlain disconformably by the unnamed member or younger sediments. Planktic foraminifera assigned to the P1 zone indicate that the JRM is Danian in age. The unnamed member is characterized by a gray-green to dark green glauconitic sand with minor thin sandy carbonates. When the JRM is absent, the unnamed member disconformably overlies the Peedee Formation with the contact marked by a thin phosphate-pebble conglomerate. The unnamed member is not as widely distributed as the Danian member, but its thickness in some areas exceeds 78 feet. The unnamed member contains up to 10% more glauconite and larger amounts of phosphatic material than the JRM. Planktic foraminifera (P4) and calcareous nannofossils (NP6) indicate that the unnamed member is Thanetian in age.« less

East Louisiana continental shelf sediments: a product of delta reworking

USGS Publications Warehouse

Brooks, Gregg R.; Kingdinger, Jack L.; Penland, Shea; Williams, S. Jeffress

1995-01-01

Data from 77 vibracores were integrated with 6,700 line-km of high- resolution seismic reflection profiles collected off the eastern Louisiana coast in the region of the St. Bernard Delta, the first of the Holocene highstand deltas of the Mississippi River. Seismic fades and sediment facies were integrated in order to establish the stratigraphic details within this relict delta. Results provide a regional geologic framework from which comparisons can be made with other areas. Holocene deposits in the study area overlie a heavily dissected surface interpreted to represent a lowstand erosional surface. Resting on this surface is a thin unit of relatively clean, quartz sand interpreted to have been deposited during early transgression. This unit is overlain by sediments of the St. Bernard Delta, a seaward-prograding, coarsening-upward wedge of sands and muds that contain vertically-stacked units of deltaic succession. Two or more prograding units separated by an unconformity, delineated from regional seismic profiles, may represent laterally shifting subdelta lobes. Surficial sediments consist of a thin unit of sands and muds derived from and reflecting the individual subenvirons of the underlying delta. Holocene inner-shelf development off eastern Louisiana has been controlled by relative sea-level rise and sediment supply. Sediment supply and deposition are a product of delta progradation and delta-lobe switching. The modern shelf configuration and surficial sediment distribution patterns reflect reworking of underlying deltaic deposits. The lack of modern sediment input helps to maintain the imprint of this ancient delta on the modern shelf surface.

Characterization of metal adsorption variability in a sand and gravel aquifer, Cape Cod, Massachusetts, U.S.A

USGS Publications Warehouse

Fuller, C.C.; Davis, J.A.; Coston, J.A.; Dixon, E.

1996-01-01

Several geochemical properties of an aquifer sediment that control metal-ion adsorption were investigated to determine their potential use as indicators of the spatial variability of metal adsorption. Over the length of a 4.5-m-long core from a sand and gravel aquifer, lead (Pb2+) and zinc (Zn2+) adsorption at constant chemical conditions (pH 5.3) varied by a factor of 2 and 4, respectively. Pb2+ and Zn2+ were adsorbed primarily by Fe- and Al-oxide coatings on quartz-grain surfaces. Per unit surface area, both Pb2+ and Zn2+ adsorption were significantly correlated with the amount of Fe and Al that dissolved from the aquifer material in a partial chemical extraction. The variability in conditional binding constants for Pb2+ and Zn2+ adsorption (log KADS) derived from a simple non-electrostatic surface complexation model were also predicted by extracted Fe and Al normalized to surface area. Because the abundance of Fe- and Al-oxide coatings that dominate adsorption does not vary inversely with grain size by a simple linear relationship, only a weak, negative correlation was found between the spatial variability of Pb2+ adsorption and grain size in this aquifer. The correlation between Zn2+ adsorption and grain size was not significant. Partial chemical extractions combined with surface-area measurements have potential use for estimating metal adsorption variability in other sand and gravel aquifers of negligible carbonate and organic carbon content.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Busch, M.; Abgrall, N.; Alvis, S. I.

Here, the Majorana Collaboration is searching for the neutrinoless double-beta decay of the nucleus 76Ge. The Majorana Demonstrator is an array of germanium detectors deployed with the aim of implementing background reduction techniques suitable for a tonne scale 76Ge-based search (the LEGEND collaboration). In the Demonstrator, germanium detectors operate in an ultra-pure vacuum cryostat at 80 K. One special challenge of an ultra-pure environment is to develop reliable cables, connectors, and electronics that do not significantly contribute to the radioactive background of the experiment. This paper highlights the experimental requirements and how these requirements were met for the Majorana Demonstrator,more » including plans to upgrade the wiring for higher reliability in the summer of 2018. Also described are requirements for LEGEND R&D efforts underway to meet these additional requirements« less

Cleaning Surface Particle Contamination with Ultrapure Water (UPW) Megasonic Flow on Genesis Array Collectors

NASA Technical Reports Server (NTRS)

Allton, J. H.; Calaway, Michael J.; Hittle, J. D.; Rodriquez, M. C.; Stansbery, E. K.; McNamara, K. M.

2006-01-01

The hard landing experienced by the Genesis sample return capsule breached the science canister containing the solar wind collectors. This impact into the damp lakebed contaminated collector surfaces with pulverized collector and spacecraft materials and Utah sediment and brine residue. The gold foil, polished aluminum, and bulk metallic glass remained intact, but the solar wind bulk and regime-specific array collectors were jarred loose from their frames and fractured into greater than 10,000 specimens. After a year of investigation and cleaning experimentation, the Genesis Science Team determined that array collectors had 4 classes of contaminants: particles, molecular film, submicron inorganic particulate ("aerosol"), and pre-launch surface contamination. We discuss here use of megasonically energized ultrapure water (UPW) for removing particulate debris from array collector fragments.

Grain Size Distribution in Mudstones: A Question of Nature vs. Nurture

NASA Astrophysics Data System (ADS)

Schieber, J.

2011-12-01

Grain size distribution in mudstones is affected by the composition of the source material, the processes of transport and deposition, and post-depositional diagenetic modification. With regard to source, it does make a difference whether for example a slate belt is eroded vs a stable craton. The former setting tends to provide a broad range of detrital quartz in the sub 62 micron size range in addition to clays and greenschist grade rock fragments, whereas the latter may be biased towards coarser quartz silt (30-60 microns), in addition to clays and mica flakes. In flume experiments, when fine grained materials are transported in turbulent flows at velocities that allow floccules to transfer to bedload, a systematic shift of grain size distribution towards an increasingly finer grained suspended load is observed as velocity is lowered. This implies that the bedload floccules are initially constructed of only the coarsest clay particles at high velocities, and that finer clay particles become incorporated into floccules as velocity is lowered. Implications for the rock record are that clay beds deposited from decelerating flows should show subtle internal grading of coarser clay particles; and that clay beds deposited from continuous fast flows should show a uniform distribution of coarse clays. Still water settled clays should show a well developed lower (coarser) and upper (finer) subdivision. A final complication arises when diagenetic processes, such as the dissolution of biogenic silica, give rise to diagenetic quartz grains in the silt to sand size range. This diagenetic silica precipitates in fossil cavities and pore spaces of uncompacted muds, and on casual inspection can be mistaken for detrital quartz. In distal mudstone successions close to 100 % of "apparent" quartz silt can be of that origin, and reworking by bottom currents can further enhance a detrital perception by producing rippled and laminated silt beds. Although understanding how size distributions in mudstones evolve is considered central to problems in hillslope, fluvial, aeolian, coastal, and submarine systems, one can not simply measure distributions and hope to arrive at an answer. The complex origins of mudstones are reflected in their very broad compositional range, and multiple overprinted processes have to be considered in order to make sense out of observed grain size distributions.

Characterization of Mechanical and Bactericidal Properties of Cement Mortars Containing Waste Glass Aggregate and Nanomaterials

PubMed Central

Sikora, Pawel; Augustyniak, Adrian; Cendrowski, Krzysztof; Horszczaruk, Elzbieta; Rucinska, Teresa; Nawrotek, Pawel; Mijowska, Ewa

2016-01-01

The recycling of waste glass is a major problem for municipalities worldwide. The problem concerns especially colored waste glass which, due to its low recycling rate as result of high level of impurity, has mostly been dumped into landfills. In recent years, a new use was found for it: instead of creating waste, it can be recycled as an additive in building materials. The aim of the study was to evaluate the possibility of manufacturing sustainable and self-cleaning cement mortars with use of commercially available nanomaterials and brown soda-lime waste glass. Mechanical and bactericidal properties of cement mortars containing brown soda-lime waste glass and commercially available nanomaterials (amorphous nanosilica and cement containing nanocrystalline titanium dioxide) were analyzed in terms of waste glass content and the effectiveness of nanomaterials. Quartz sand is replaced with brown waste glass at ratios of 25%, 50%, 75% and 100% by weight. Study has shown that waste glass can act as a successful replacement for sand (up to 100%) to produce cement mortars while nanosilica is incorporated. Additionally, a positive effect of waste glass aggregate for bactericidal properties of cement mortars was observed. PMID:28773823

Water Flow Investigation on Quartz Sand with 13-interval Stimulated Echo Multi Slice Imaging

NASA Astrophysics Data System (ADS)

Spindler, Natascha; Pohlmeier, Andreas; Galvosas, Petrik

2011-03-01

Understanding root water uptake in soils is of high importance for securing nutrition in the context of climate change and linked phenomena like stronger varying weather conditions (draught, strong rain). One step to understand how root water uptake occurs is the knowledge of the water flow in soil towards plant roots. Magnetic Resonance Imaging (MRI) in combination with q-space imaging is potentially the most powerful analytical tool for non-invasive three dimensional visualization of flow and transport in porous media. Numerous attempts have been made to measure local velocity in porous media by combining velocity phase encoding with fast imaging methods, where flow velocities in the vascular bundles of plant stems were investigated. In contrast to water situated in the cellular structure of plants, NMR signal arising from water in the pore space in soil may be much more affected by the presence of internal magnetic field gradients. In this work we account for the existence of these gradients by employing bipolar pulsed field magnetic gradients for velocity encoding. This enables one to study flow through sand (as a model system for soil) at flow rates relevant for the water uptake of plant roots.

Characterization of Mechanical and Bactericidal Properties of Cement Mortars Containing Waste Glass Aggregate and Nanomaterials.

PubMed

Sikora, Pawel; Augustyniak, Adrian; Cendrowski, Krzysztof; Horszczaruk, Elzbieta; Rucinska, Teresa; Nawrotek, Pawel; Mijowska, Ewa

2016-08-18

The recycling of waste glass is a major problem for municipalities worldwide. The problem concerns especially colored waste glass which, due to its low recycling rate as result of high level of impurity, has mostly been dumped into landfills. In recent years, a new use was found for it: instead of creating waste, it can be recycled as an additive in building materials. The aim of the study was to evaluate the possibility of manufacturing sustainable and self-cleaning cement mortars with use of commercially available nanomaterials and brown soda-lime waste glass. Mechanical and bactericidal properties of cement mortars containing brown soda-lime waste glass and commercially available nanomaterials (amorphous nanosilica and cement containing nanocrystalline titanium dioxide) were analyzed in terms of waste glass content and the effectiveness of nanomaterials. Quartz sand is replaced with brown waste glass at ratios of 25%, 50%, 75% and 100% by weight. Study has shown that waste glass can act as a successful replacement for sand (up to 100%) to produce cement mortars while nanosilica is incorporated. Additionally, a positive effect of waste glass aggregate for bactericidal properties of cement mortars was observed.

Assessment of Envi-Carb™ as a passive sampler binding phase for acid herbicides without pH adjustment.

PubMed

Seen, Andrew; Bizeau, Oceane; Sadler, Lachlan; Jordan, Timothy; Nichols, David

2014-05-01

The graphitised carbon solid phase extraction (SPE) sorbent Envi-Carb has been used to fabricate glass fibre filter- Envi-Carb "sandwich" disks for use as a passive sampler for acid herbicides. Passive sampler uptake of a suite of herbicides, including the phenoxyacetic acid herbicides 4-chloro-o-tolyloxyacetic acid (MCPA), 2,4-dichlorophenoxyacetic acid (2,4-D) and 3,6-dichloro-2-methoxybenzoic acid (Dicamba), was achieved without pH adjustment, demonstrating for the first time a suitable binding phase for passive sampling of acid herbicides at neutral pH. Passive sampling experiments with Duck River (Tasmania, Australia) water spiked at 0.5 μg L(-1) herbicide concentration over a 7 d deployment period showed that sampling rates in Duck River water decreased for seven out of eight herbicides, and in the cases of 3,6-dichloro-2-pyridinecarboxylic acid (Clopyralid) and Dicamba no accumulation of the herbicides occurred in the Envi-Carb over the deployment period. Sampling rates for 4-amino-3,5,6-trichloro-2-pyridinecarboxylic acid (Picloram), 2,4-D and MCPA decreased to approximately 30% of the sampling rates in ultrapure water, whilst sampling rates for 2-(4,6-dimethylpyrimidin-2-ylcarbamoylsulfamoyl) benzoic acid, methyl ester (Sulfometuron-methyl) and 3,5,6-Trichloro-2-pyridinyloxyacetic acid (Triclopyr) were approximately 60% of the ultrapure water sampling rate. For methyl N-(2,6-dimethylphenyl)-N-(methoxyacetyl)-D-alaninate (Metalaxyl-M) there was little variation in sampling rate between passive sampling experiments in ultrapure water and Duck River water. SPE experiments undertaken with Envi-Carb disks using ultrapure water and filtered and unfiltered Duck River water showed that not only is adsorption onto particulate matter in Duck River water responsible for a reduction in herbicide sampling rate, but interactions of herbicides with dissolved or colloidal matter (matter able to pass through a 0.2 μm membrane filter) also reduces the herbicide sampling rate. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Mineralogical characterization of rendering mortars from decorative details of a baroque building in Kozuchow (SW Poland)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartz, W., E-mail: wojciech.bartz@ing.uni.wroc.pl; Filar, T.

Optical microscopic observations, scanning electron microscopy and microprobe with energy dispersive X-ray analysis, X-ray diffraction and differential thermal/thermogravimetric analysis allowed detailed characterization of rendering mortars from decorative details (figures of Saints) of a baroque building in Kozuchow (Lubuskie Voivodship, Western Poland). Two separate coats of rendering mortars have been distinguished, differing in composition of their filler. The under coat mortar has filler composed of coarse-grained siliceous sand, whereas the finishing one has much finer grained filler, dominated by a mixture of charcoal and Fe-smelting slag, with minor amounts of quartz grains. Both mortars have air-hardening binder composed of gypsum andmore » micritic calcite, exhibiting microcrystalline structure.« less

Characteristics Of Basaltic Sand: Size, Shape, And Composition As A Function Of Transport Process And Distance

NASA Astrophysics Data System (ADS)

Craddock, R. A.; Needell, Z. A.; Rose, T. R.

2012-04-01

Overview: The chemical and physical characteristics of sedimentary material can provide valuable clues about transport processes, distance traveled, and provenance, all of which are aspects of Martian geography that we would like to better understand. For a typical sedimentary deposit on Earth, for example, it has been shown that the ratio of feldspar to quartz can be used to assess the maturity (or transport distance) of a terrestrial deposit, because feldspar is more vulnerable to weathering than quartz. Further, chemical analysis can also be used to determine potential sediment sources, and grain-size sorting can be used to distinguish aeolian sediments (typically well-sorted) from fluvial sediments (poorly sorted in high energy environments). It is also common to use the shapes of individual quartz particles to determine transport process and distance, all of which can help us better understand the history of a sample of sedimentary material and the geological processes that created and emplaced it. These traditional sedimentological concepts are now being applied to our interpretation of Martian surface materials. Sullivan et al. [2008], for example, used grain-size and shape to assess eolian processes and to qualify transport distances of deposits found at the Spirit landing site in Gusev Crater. Stockstill-Cahill et al. [62008 used variations in mineral abundances observed in multispectral data to determine the provenance of dark dunes found in Amazonis Planitia craters. While applying our understanding of terrestrial sedimentary materials to Martian surface materials is intuitively sound and logical, the problem is that most of our current understanding is based on sediments derived from felsic materials (e.g., granite) primarily because that is the composition of most of the landmass on the Earth. However, the Martian surface is composed primarily of mafic material, or basalt, which generates much different sedimentary particles as it weathers. Instead of quartz, feldspar, and heavy minerals commonly found in most terrestrial sedimentary deposits, basaltic sediments are composed of varying amounts of olivine, pyroxene, plagioclase, and vitric and lithic fragments. One of the few locations on Earth containing such material is the Ka'u Desert of Hawaii. This area is unique in that both eolian and fluvial sediment pathways occur in the same area, thus allowing a direct comparison of particles transported by different processes over identical distances (~20 km). We are currently documenting the physical and chemical changes that take place in basaltic sediments as they are transported by wind and water over increasing distances. This will result in an improvement in our understanding of traditional sedimentological concepts when applying them to Martian surface materials. Process: The Ka'u Desert is ~350 km2 and contains the largest basaltic dune fields on Earth. We have identified several different dune types located in various parts of the desert, including climbing and falling dunes, sand sheets, parabolic dunes (that were initially barchans), and crescentic dunes. Fluvial sediments occur as floodout deposits where ephemeral streams go from confined to unconfined flow outside the continuous Keanakako'i Formation [7]. There are also a number of sand bottom streams and playas that occur along a series of channels that extend from the Keanakako'i Formation ~20 km to the sea. We have collected samples from dunes and fluvial deposits at various locations in the Ka'u Desert, at varying distances from sources and subject to different environmental processes. In the lab, we have begun to use optical and scanning electron microscopic images to assess how grain size, shape, and angularity of individual particles change with increasing transport distances. We are also conducting point counts of particles contained within each sample to better understand how olivine, pyroxene, feldspar, and lithic and vitric fragments weather with increasing transport distances. Selected samples are being analyzed for changes in chemistry. The results from this study will help us to understand how basaltic sediments may weather physically and chemically on Mars, and it may provide additional insights into the formation of Martian soils and dust. In addition, we are conducting statistical analyses of our samples using photographs from an optical microscope; analyses that could be easily performed in situ by a rover. By spreading the loose material on a blank background and photographing from above, we are obtaining 2-D projections of grain sizes and shapes. Using simple morphological operations to separate touching grains, we are obtaining grain size distribution weighted by number fraction, area fraction, or estimated volume fraction—giving much better grain size resolution and requiring much less labor than sieving. Further, we are using the resulting 2-D images to perform Fourier grain shape analyses, similar to those proposed by Ehrlich and Weinberg [1970], where the perimeter of each grain is broken down into its fourier components and the weights of each harmonic are averaged over a large number of grains. This averaged spectrum gives a quantitative measure of the roughness and angularity of the grain shape and has been used to determine the sources of mixed populations of quartz particles. The results from our study will provide information needed to determine provenance and transport distances of sedimentary material imaged by MER, MSL and the 2018 lander. Observations: To date, our results have been mostly qualitative. From exposed cross sections and test augers, we know that the stratigraphy within the dunes is complicated, and generally reflects the stratigraphy of the Keanakako'i Formation itself (e.g., more vitric-rich sands are generally in the lower part of the sections). It is not immediately clear if layers within the dunes are the result of local reworking of the tephra, or if the material was transported several to tens of kilometers. There is also the basic question of when and how the dunes actually formed. This requires a better understanding of both the lithology and timing of events, which will come with further analysis. Our preliminary grain size studies have also shown expected results. We found stratification of the sand in a climbing dune, with the material composing the lower part of the dune being bimodal, made up of a fine dust and coarse, dark lithic grains, while the material from the upper part of the dune is better sorted, consisting of relatively fine grained dark sand.

The influence of oxidation reduction potential and water treatment processes on quartz lamp sleeve fouling in ultraviolet disinfection reactors.

PubMed

Wait, Isaac W; Johnston, Cliff T; Blatchley, Ernest R

2007-06-01

Ultraviolet (UV) disinfection systems are incorporated into drinking water production facilities because of their broad-spectrum antimicrobial capabilities, and the minimal disinfection by-product formation that generally accompanies their use. Selection of an optimal location for a UV system within a drinking water treatment facility depends on many factors; a potentially important consideration is the effect of system location on operation and maintenance issues, including the potential for fouling of quartz surfaces. To examine the effect of system location on fouling, experiments were conducted at a groundwater treatment facility, wherein aeration, chlorination, and sand filtration were applied sequentially for treatment. In this facility, access to the water stream was available prior to and following each of the treatment steps. Therefore, it was possible to examine the effects of each of these unit operations on fouling dynamics within a UV system. Results indicated zero-order formation kinetics for the fouling reactions at all locations. Increases in oxidation reduction potential, caused by water treatment steps such as aeration and chlorination, increased the rate of sleeve fouling and the rate of irradiance loss within the reactor. Analysis of metals in the sleeve foulant showed that calcium and iron predominate, and relative comparisons of foulant composition to water chemistry highlighted a high affinity for incorporation into the foulant matrix for both iron and manganese, particularly after oxidizing treatment steps. Fouling behavior was observed to be in qualitative agreement with representations of the degree of saturation, relative to the metal:ligand combinations that are believed to comprise a large fraction of the foulants that accumulate on the surfaces of quartz jackets in UV systems used to treat water.

Respiratory exposures associated with silicon carbide production: estimation of cumulative exposures for an epidemiological study.

PubMed Central

Smith, T J; Hammond, S K; Laidlaw, F; Fine, S

1984-01-01

Silicon carbide is produced by heating a mixture of petroleum coke and silica sand to approximately 2000 degrees C in an electric furnace for 36 hours. During heating, large amounts of carbon monoxide are released, sulphur dioxide is produced from residual sulphur in the coke, and hydrocarbon fume is produced by pyrolysis of the coke. Loading and unloading furnaces causes exposures to respirable dust containing crystalline silica, silicon carbide, and hydrocarbons. In the autumn of 1980 extensive measurements were made of personal exposures to air contaminants. Eight hour time weighted exposures to sulphur dioxide ranged from less than 0.1 ppm to 1.5 ppm and respirable participate exposures ranged from 0.01 mg/m3 to 9.0 mg/m3. Geometric mean particulate exposures for jobs ranged from 0.1 mg/m3 to 1.46 mg/m3. The particulate contained varying amounts of alpha-quartz, ranging from less than 1% to 17%, and most quartz exposures were substantially below the threshold limit value of 100 micrograms/m3. Only traces of cristobalite (less than 1%) were found in the particulate. Median exposures to air contaminants in each job were estimated. Since the operations at the plant had been stable over the past 30 years, it was possible to estimate long term exposures of workers to sulphur dioxide, respirable particulate, quartz, total inorganic material, and extractable organic material. Cumulative exposure (average concentration times exposure duration) for each of the air contaminants was estimated for each worker using his job history. There was sufficient independent variability in the sulphur dioxide and respirable particulate cumulative exposures to make an assessment of their independent effects feasible. The theoretical basis for using the cumulative exposure index and its shortcomings for epidemiological applications were presented. PMID:6691927

The Effect of Interfacial Chemical Bonding in TiO2-SiO2 Composites on Their Photocatalytic NOx Abatement Performance

PubMed Central

Hakki, Amer; Yang, Lu; Wang, Fazhou; Macphee, Donald E.

2017-01-01

The chemical bonding of particulate photocatalysts to supporting material surfaces is of great importance in engineering more efficient and practical photocatalytic structures. However, the influence of such chemical bonding on the optical and surface properties of the photocatalyst and thus its photocatalytic activity/reaction selectivity behavior has not been systematically studied. In this investigation, TiO2 has been supported on the surface of SiO2 by means of two different methods: (i) by the in situ formation of TiO2 in the presence of sand quartz via a sol-gel method employing tetrabutyl orthotitanium (TBOT); and (ii) by binding the commercial TiO2 powder to quartz on a surface silica gel layer formed from the reaction of quartz with tetraethylorthosilicate (TEOS). For comparison, TiO2 nanoparticles were also deposited on the surfaces of a more reactive SiO2 prepared by a hydrolysis-controlled sol-gel technique as well as through a sol-gel route from TiO2 and SiO2 precursors. The combination of TiO2 and SiO2, through interfacial Ti-O-Si bonds, was confirmed by FTIR spectroscopy and the photocatalytic activities of the obtained composites were tested for photocatalytic degradation of NO according to the ISO standard method (ISO 22197−1). The electron microscope images of the obtained materials showed that variable photocatalyst coverage of the support surface can successfully be achieved but the photocatalytic activity towards NO removal was found to be affected by the preparation method and the nitrate selectivity is adversely affected by Ti-O-Si bonding. PMID:28715384

Ultrapure glass optical waveguide development in microgravity by the sol-gel process

NASA Technical Reports Server (NTRS)

1982-01-01

Containerless melting of glasses in space for the preparation of ultrapure homogeneous glass for optical waveguides is discussed. The homogenization of the glass using conventional raw materials is normally achieved on Earth either by the gravity induced convection currents or by the mechanical stirring of the melt. Because of the absence of gravity induced convection currents, the homogenization of glass using convectional raw materials is difficult in the space environment. Multicomponent, homogeneous, noncrystalline oxide gels can be prepared by the sol-gel process and these gels are promising starting materials for melting glasses in the space environment. The sol-gel process is based on the polymerization reaction of alkoxysilane with other metal alkoxy compounds or suitable metal salts. Many of the alkoxysilanes or other metal alkoxides are liquids and thus can be purified by distillation.

Low background materials and fabrication techniques for cables and connectors in the Majorana Demonstrator

NASA Astrophysics Data System (ADS)

Busch, M.; Abgrall, N.; Alvis, S. I.; Arnquist, I. J.; Avignone, F. T.; Barabash, A. S.; Barton, C. J.; Bertrand, F. E.; Bode, T.; Bradley, A. W.; Brudanin, V.; Buuck, M.; Caldwell, T. S.; Chan, Y.-D.; Christofferson, C. D.; Chu, P.-H.; Cuesta, C.; Detwiler, J. A.; Dunagan, C.; Efremenko, Yu.; Ejiri, H.; Elliott, S. R.; Gilliss, T.; Giovanetti, G. K.; Green, M. P.; Gruszko, J.; Guinn, I. S.; Guiseppe, V. E.; Haufe, C. R.; Hehn, L.; Henning, R.; Hoppe, E. W.; Howe, M. A.; Keeter, K. J.; Kidd, M. F.; Konovalov, S. I.; Kouzes, R. T.; Lopez, A. M.; Martin, R. D.; Massarczyk, R.; Meijer, S. J.; Mertens, S.; Myslik, J.; O'Shaughnessy, C.; Othman, G.; Poon, A. W. P.; Radford, D. C.; Rager, J.; Reine, A. L.; Rielage, K.; Robertson, R. G. H.; Rouf, N. W.; Shanks, B.; Shirchenko, M.; Suriano, A. M.; Tedeschi, D.; Trimble, J. E.; Varner, R. L.; Vasilyev, S.; Vetter, K.; Vorren, K.; White, B. R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Yu, C.-H.; Yumatov, V.; Zhitnikov, I.; Zhu, B. X.

2018-01-01

The Majorana Collaboration is searching for the neutrinoless double-beta decay of the nucleus 76Ge. The Majorana Demonstrator is an array of germanium detectors deployed with the aim of implementing background reduction techniques suitable for a tonne scale 76Ge-based search (the LEGEND collaboration). In the Demonstrator, germanium detectors operate in an ultra-pure vacuum cryostat at 80 K. One special challenge of an ultra-pure environment is to develop reliable cables, connectors, and electronics that do not significantly contribute to the radioactive background of the experiment. This paper highlights the experimental requirements and how these requirements were met for the Majorana Demonstrator, including plans to upgrade the wiring for higher reliability in the summer of 2018. Also described are requirements for LEGEND R&D efforts underway to meet these additional requirements

Ultrapure Green Light-Emitting Diodes Using Two-Dimensional Formamidinium Perovskites: Achieving Recommendation 2020 Color Coordinates.

PubMed

Kumar, Sudhir; Jagielski, Jakub; Kallikounis, Nikolaos; Kim, Young-Hoon; Wolf, Christoph; Jenny, Florian; Tian, Tian; Hofer, Corinne J; Chiu, Yu-Cheng; Stark, Wendelin J; Lee, Tae-Woo; Shih, Chih-Jen

2017-09-13

Pure green light-emitting diodes (LEDs) are essential for realizing an ultrawide color gamut in next-generation displays, as is defined by the recommendation (Rec.) 2020 standard. However, because the human eye is more sensitive to the green spectral region, it is not yet possible to achieve an ultrapure green electroluminescence (EL) with a sufficiently narrow bandwidth that covers >95% of the Rec. 2020 standard in the CIE 1931 color space. Here, we demonstrate efficient, ultrapure green EL based on the colloidal two-dimensional (2D) formamidinium lead bromide (FAPbBr 3 ) hybrid perovskites. Through the dielectric quantum well (DQW) engineering, the quantum-confined 2D FAPbBr 3 perovskites exhibit a high exciton binding energy of 162 meV, resulting in a high photoluminescence quantum yield (PLQY) of ∼92% in the spin-coated films. Our optimized LED devices show a maximum current efficiency (η CE ) of 13.02 cd A -1 and the CIE 1931 color coordinates of (0.168, 0.773). The color gamut covers 97% and 99% of the Rec. 2020 standard in the CIE 1931 and the CIE 1976 color space, respectively, representing the "greenest" LEDs ever reported. Moreover, the device shows only a ∼10% roll-off in η CE (11.3 cd A -1 ) at 1000 cd m -2 . We further demonstrate large-area (3 cm 2 ) and ultraflexible (bending radius of 2 mm) LEDs based on 2D perovskites.

Is Kissamos Bay in NW Crete, Greece worth to be exploited as a marine aggregates deposit? An integrated approach

NASA Astrophysics Data System (ADS)

Anastasatou, Marianthi; Tsoutsia, Antonia; Petrakis, Stelios; Rousakis, Grigoris; Karditsa, Aikaterini; Hasiotis, Thomas; Kapsimalis, Vasilios; Poulos, Serafim; Stamatakis, Michael

2017-04-01

This study uses an integrated approach to investigate the offshore area of Kissamos Bay, NW Crete Island, Greece, as a prospective marine aggregate (MA) deposit. Non-fuel marine minerals and especially marine aggregates (sand and gravel) are reviewed from the perspective of resources during the last decades. The possible MA deposit of Kissamos Bay was explored during the implementation of the research project THALES-MARE, considering existing information of previous extraction activities in the wider area. Kissamos Bay is located at the inner continental shelf off NW Crete. The onshore basement rocks are composed of Mesozoic to Eocene limestones, shale and sandstone units, along with Neogene sediments such as marls, sandstones and claystones, which locally host Messinian gypsum layers. Sixteen sea-bottom sediment samples were collected with a Smith-McIntyretype grab along four transects, vertical to the shoreline, at water depths of 11 to 44m. A sub-bottom acoustic profiler survey was conducted in order to quantitatively determine the deposit (dimensions and structure). Mineralogical, geochemical, sedimentological and benthic analyses of the samples were carried out, in order to determine the quality of the reservoir and the environmental impact of a potential exploitation. Mineralogical results indicated that the bulk samples consist predominantly of quartz, while calcite occurs as a second significant phase. Chemical analysis of major and trace elements revealed that the average SiO2 content is around 55% with samples closer to the beach (depths <15m) reaching 70%. SO3 content, attributed to the presence of gypsum, is lower than 1%. The Cl- content of the unwashed material reflected mainly the presence of halite and is approximately 0.2%. The results of the benthic analysis indicated that no pressure will occur at the local ecosystem due to a potential exploitation of the deposit. Granulometric analysis of the sediments indicated that the main particle size composition is sand with extended spots of coarser material (gravel) in the western part of the bay, while the finer fraction (mud) increases in greater depths ( 40m). After the analysis of the seismic profiles, it was estimated that the surface area of the deposit is approximately 12.25 km2 and the volume of the sand and gravels is about 0.4 km3, whereas the average specific weight of the sediments in the study area is 2.5-3 g/cm3. The aforementioned results support the idea that Kissamos Bay can be a promising area for marine aggregate exploitation, regarding beach replenishment and the wider construction industry. However, with respect to silica content, a better quality (quartz sand) is required for cement applications. Acknowledgments: This work was supported by the research program THALES-MARE (MIS: 375655), funded by the Operational Programme "Education and lifelong learning, 2007-2013" of the Ministry of Education and Religious Affairs, Culture and Sports.

The influence of wetting dynamics on the residual air distribution

NASA Astrophysics Data System (ADS)

Sacha, J.; Snehota, M.; Trtik, P.; Vontobel, P.

2016-12-01

The amount and distribution of the residual air during the infiltration into a porous soil system has a strong influence on the infiltration rate. Concurrently, the amount of residual air is dependent on the wetting dynamics. In the presented study, two experiments were conducted on the same sample. The first experiment was performed under the constant water level condition (CWL) and the second under the constant water flux condition (CWF) at the top of the sample. The sample that composed of coarse and medium coarse fractions of sand and fine porous ceramics was packed into the quartz glass columns of the inner diameter of 29 mm. The coarse sand represented a highly conductive region connected from the top to the bottom of the sample with the exception of three low (2-3 mm) separation layers made up of the medium coarse sand. Three discs of fine ceramic formed slow flow regions. Infiltration experiments were monitored by neutron radiography on two different beamlines to produce two-dimensional (2D) projections. The CWL experiment was monitored by NEUTRA station with an acquisition time of 16 seconds per projection and the CWF experiment was visualized at BOA station with an acquisition time of 0.25 seconds per projection. Both stations are located at the Paul Scherrer Institut, Switzerland. The acquired radiograms of the dry sample were subtracted from all subsequent radiograms to determine the water thickness in projections. From series of corrected radiograms taken at the different angles three-dimensional (3D) image was reconstructed for steady state part of the experiment CWL and for entire experiment CWF. Then the series of 3D images mapped the wetting of the porous system over the corresponding phase of infiltration process. The results showed a faster steady state infiltration rate during the CWL. In this case, the air was mostly pushed out from the sample by moving wetting front. On the contrary, during the CWF the water infiltrated into the fine ceramics first and then into the medium coarse sand attracted by stronger capillary forces in comparison to the coarse sand. Due to this effect a significant amount of air was trapped in preferential pathways, and consequently blocking the water flow. The presence of medium coarse sand regions had a crucial impact on the water flow and amount of air trapping.

Direct Measurements of Surface Energy, Elastic Modulus and Interparticle Forces of Titan Aerosol Analog (`Tholin') Using Atomic Force Microscopy

NASA Astrophysics Data System (ADS)

Yu, X.; Horst, S. M.; He, C.; McGuiggan, P.; Bridges, N. T.

2017-12-01

To understand the origin of the dunes on Titan, it is important to investigate the material properties of the sand particles on Titan, which are mainly made of organics deposited from the atmosphere [1]. The organic sand may behave differently compared to the quartz/basaltic sand on terrestrial planets (Earth, Venus, Mars) in terms of interparticle forces. We measured the surface energy (through contact angle measurements) and elastic modulus (through Atomic Force Microscopy, AFM) of Titan aerosol analog (tholins) produced in our lab. Tholins may be compositionally similar to sand on Titan. We directly measured the interparticle forces between a tholin particle adhered to an AFM cantilver and tholin particles on a substrate. We also measured the properties of walnut shells, a typical material used in the Titan Wind Tunnel (TWT, [2, 3]). We find the surface energy of a tholin thin film is about 70.9 mN/m and its elastic modulus is about 3.5 GPa (similar to hard polymers like PMMA and polystyrene). We used the two measured material properties of tholin to calculate its interparticle cohesion assuming simple sphere-sphere geometry [4]. For two 20 µm particles, the theoretical cohesion force is about 6682 nN. Under dry nitrogen (RH<1%), the directly measured interparticle forces using AFM was approximately 4000 nN, which is smaller than theoretical predictions but still relatively strong under dry conditions. The interparticle cohesion between walnut shell particles is only 200 nN, which is much lower than between tholin particles. The key finding of this study is that the interparticle cohesion forces are much larger for tholins and presumably Titan sand particles than for terrestrial sand and materials used in the wind tunnel. This suggests we should increase the interparticle force in both analog experiments (TWT) and threshold models (e.g. [5]) to correctly translate the results to real Titan conditions. The strong cohesion of tholins may also inform us how the small aerosol particles ( 1 µm) in Titan's atmosphere are transformed into large sand particles ( 200 µm). References: [1] J. W. Barnes et al. Icarus, 195, 400, 2008. [2] D. M. Burr, et al. Nat., 517, 60, 2015. [3] X. Yu et al., Icarus, 297, 97, 2017. [4] K. L. Johnson et al., Proc. R. Soc. Lond., A 324, 301, 1971. [5] Y. Shao & H. Lu, J. Geophys. Res., 105, 22437, 2000.

Shear dilatancy and acoustic emission in dry and saturated granular materials

NASA Astrophysics Data System (ADS)

Brodsky, E. E.; Siman-Tov, S.

2017-12-01

Shearing of granular materials plays a strong role in naturally sheared systems as landslides and faults. Many works on granular flows have concentrated on dry materials, but relatively little work has been done on water saturated sands. Here we experimentally investigate dry versus saturated quartz-rich sand to understand the effect of the fluid medium on the rheology and acoustic waves emission of the sheared sand. The sand was sheared in a rotary shear rheometer under applied constant normal stress boundary at low (100 µm/s) to high (1 m/s) velocities. Mechanical, acoustic data and deformation were continuously recorded and imaged. For dry and water saturated experiments the granular volume remains constant for low shear velocities ( 10-3 m/s) and increases during shearing at higher velocities ( 1 m/s). Continuous imaging of the sheared sand show that the steady state shear band thickness is thicker during the high velocity steps. No significant change observed in the shear band thickness between dry and water saturated experiments. In contrast, the amount of dilation during water saturated experiments is about half the value measured for dry material. The measured decrease cannot be explained by shear band thickness change as such is not exist. However, the reduced dilation is supported by our acoustic measurements. In general, the event rate and acoustic event amplitudes increase with shear velocity. While isolated events are clearly detected during low velocities at higher the events overlap, resulting in a noisy signal. Although detection is better for saturated experiments, during the high velocity steps the acoustic energy measured from the signal is lower compared to that recorded for dry experiments. We suggest that the presence of fluid suppresses grain motion and particles impacts leading to mild increase in the internal pressure and therefore for the reduced dilation. In addition, the viscosity of fluids may influence the internal pressure via hydrodynamic lubrication which increases the fluid pressure and therefore increases the dilation compared to dry material. The effect is particularly strong for high viscosity fluids, as observed in the silicon oil experiment. Therefore, fluid viscosity can play a crucial role in determining the physics that controls the rheology of the sheared material.

Submarine fans: Characteristics, models, classification, and reservoir potential

NASA Astrophysics Data System (ADS)

Shanmugam, G.; Moiola, R. J.

1988-02-01

Submarine-fan sequences are important hydrocarbon reservoirs throughout the world. Submarine-fan sequences may be interpreted from bed-thickness trends, turbidite facies associations, log motifs, and seismic-reflection profiles. Turbidites occurring predominantly in channels and lobes (or sheet sands) constitute the major portion of submarine-fan sequences. Thinning- and thickening-upward trends are suggestive of channel and lobe deposition, respectively. Mounded seismic reflections are commonly indicative of lower-fan depositional lobes. Fan models are discussed in terms of modern and ancient fans, attached and detached lobes, highly efficient and poorly efficient systems, and transverse and longitudinal fans. In general, depositional lobes are considered to be attached to feeder channels. Submarine fans can be classified into four types based on their tectonic settings: (1) immature passive-margin fans (North Sea type); (2) mature passive-margin fans (Atlantic type); (3) active-margin fans (Pacific type); and (4) mixed-setting fans. Immature passive-margin fans (e.g., Balder, North Sea), and active-margin fans (e.g., Navy, Pacific Ocean) are usually small, sand-rich, and possess well developed lobes. Mature passive-margin fans (e.g., Amazon, Atlantic Ocean) are large, mud-rich, and do not develop typical lobes. However, sheet sands are common in the lower-fan regions of mature passive-margin fans. Mixed-setting fans display characteristics of either Atlantic type (e.g., Bengal, Bay of Bengal), or Pacific type (Orinoco, Caribbean), or both. Conventional channel-lobe models may not be applicable to fans associated with mature passive margins. Submarine fans develop primarily during periods of low sea level on both active- and passive-margin settings. Consequently, hydrocarbon-bearing fan sequences are associated generally with global lowstands of sea level. Channel-fill sandstones in most tectonic settings are potential reservoirs. Lobes exhibit the most favorable reservoir quality in terms of sand content, lateral continuity, and porosity development. Lower-fan sheet sands may also make good reservoirs. Quartz-rich sandstones of mature passive-margin fans are most likely to preserve depositional porosity, whereas lithic sandstones of active-margin fans may not.

The Late Holocene Stratigraphy of an Inlet-Dominated Barrier Island, Pea Island, North Carolina.

NASA Astrophysics Data System (ADS)

Smith, C. G.; Ames, D.; Corbett, D. R.; Culver, S.; Mallinson, D.; Riggs, S. R.; Vance, D.

2002-12-01

Sedimentological, foraminiferal, geochemical, and geophysical data sets as well as aerial photographs have been used to investigate the natural processes (inlet dynamics, ocean/estuarine washover, and sea-level change) responsible for the late Holocene units preserved in the barrier island subsurface at Pea Island National Wildlife Refuge. Historic nautical charts indicate that three inlets characterized Pea Island between early European exploration (1590) and the late 19th century; aerial photographs show New Inlet open in 1932 and 1940. Vibracores (up to 5.5 m) collected along three transects across Pea Island extend our knowledge of the geological evolution of this region to pre-historic times. The section in the longest core (PI01S6) consists of four fining-upwards depositional sequences. The basal unit of each sequence is a bedded, medium to fine, clean quartz sand with increasing concentrations of organic matter (3-4 % detrital and 5-7 % in situ Spartina alterniflora roots) or irregular mud clasts (2-5 cm) to spherical mud balls (1-2 cm) up core. The clean sand units have so far proven to be barren of foraminifera except for a shelly unit at ca. 220 cm below MSL. The foraminiferal assemblage in this unit is of open shelf character (Elphidium excavatum, Hanzawaia strattoni, and Buccella inusitata). A 14C age on a disarticulated Chione cancellata valve from this unit is cal. 930+/-60 BP. The sand grades into a gray, tight mud in the first two sequences and into an inter-laminated mud and in situ peat in the third sequence. The peat contains leaf fragments and rhizomes of the marsh plants Juncus roemarianus, Spartina cynosuroides, and/or Phragmites spp. The peat and muddy sand units contain marsh foraminifera (Trochammina spp., Miliammina fusca, Arenoparrella mexicana), which are also found in modern marsh deposits. A peat sample from the third fining upward sequence (the only one to grade into a true peat) has a 14C age of cal. 395+/-35 BP, cal. 295+/-35 BP, or cal 180+/-40 BP. The four fining-upwards sequences have sharp erosional basal contacts. These deposits appear to reflect back-barrier processes including sequential deposition of flood-tide delta sands and/or sound sands adjacent to marshes. The shelly sands, containing open shelf foraminiferal assemblages, represent oceanic overwash, inlet deposits, or open embayment sands deposited behind a laterally extensive breach in the barrier island. The sequences are capped by the deposits of modern environments that include algal flats, tidal creeks, high and low marshes, back-barrier berms, overwash fans, and aeolian dunes. Several of the modern environments became covered with marsh vegetation after the construction of barrier dune ridges in the late 1930?s.

Arsenic, metals, and nutrients in runoff from two detention basins to Raccoon Creek, New Jersey Coastal Plain, 2008

USGS Publications Warehouse

Barringer, Julia L.; Szabo, Zoltan; Bonin, Jennifer L.; McGee, Craig K.

2011-01-01

Arsenic (As) concentrations in the waters of Raccoon Creek in southern New Jersey commonly exceed the State\\'s Surface Water Quality Standard (SWQS) for freshwater of 0.017 microgram per liter (mu or ug/L). In order to assess contributions of As from residential runoff to the creek, samples of runoff water were collected from a detention basin in each of two residential developments underlain by different geologic formations and at the outlets of those basins. Samples of streamwater also were collected from Raccoon Creek adjacent to the developments. The samples were analyzed to determine concentrations of As, selected metals, organic carbon, and nutrients. Soil samples in and downgradient from the basins also were collected and analyzed. Concentrations of As in unfiltered water samples of runoff from the basin underlain by glauconitic clays generally were higher (up to 4.35 mu or ug/L) than in runoff from the basin underlain by predominantly quartz sands and silts (up to 2.68 mu or ug/L). Chromium (Cr) concentrations also were higher in runoff from the basin underlain by glauconitic clays than in runoff from the basin underlain by quartz sand and silt. In addition, Cr concentrations were higher in the glauconitic soils than in the quartz-rich soils. Metals such as aluminum (Al), iron (Fe), lead (Pb), and manganese (Mn) in the runoff and in the streamwater were mostly in particulate form. Arsenic, most metals, and phosphorus (P) however, were mostly in dissolved form in runoff but in particulate form in the streamwater. Total organic carbon concentrations in the runoff ranged from about 10 to nearly 16 milligrams per liter (mg/L). Given such levels of organic carbon and strong correlations between concentrations of some metals and organic carbon, it may be that many of the metals were complexed with dissolved organic carbon and transported in that form in the runoff. Although underlying geologic materials and soils appear to be major contributors of As to the streamwater, As also could have been contributed from lead arsenate pesticide residues. The residential development underlain by quartz-rich sediments formerly had been an orchard where such pesticides may have been used. The substantial inputs of As to runoff at this site may be attributable to this former land use, although Pb concentrations were about the same in runoff from both sites. The streamwater at both sites, however, contained Pb concentrations well above those in runoff, indicating that there are additional inputs of Pb, perhaps from roadside soils, upstream from the two sampling sites in this study. Positive relations between concentrations of As and some metals with dissolved organic carbon in runoff and streamwater indicate that complexation with organic carbon may provide a mechanism by which these constituents can be transported. Sorption of As, Pb, and P to Fe hydroxides may be indicated by the observed positive relation of particulate As, Pb, and P to particulate Fe, however, representing an additional mechanism for transport of these constituents.

On extracting sediment transport information from measurements of luminescence in river sediment

USGS Publications Warehouse

Gray, Harrison J.; Tucker, Gregory E.; Mahan, Shannon; McGuire, Chris; Rhodes, Edward J.

2017-01-01

Accurately quantifying sediment transport rates in rivers remains an important goal for geomorphologists, hydraulic engineers, and environmental scientists. However, current techniques for measuring long-time scale (102–106 years) transport rates are laborious, and formulae to predict transport are notoriously inaccurate. Here we attempt to estimate sediment transport rates by using luminescence, a property of common sedimentary minerals that is used by the geoscience community for geochronology. This method is advantageous because of the ease of measurement on ubiquitous quartz and feldspar sand. We develop a model from first principles by using conservation of energy and sediment mass to explain the downstream pattern of luminescence in river channel sediment. We show that the model can accurately reproduce the luminescence observed in previously published field measurements from two rivers with very different sediment transport styles. The model demonstrates that the downstream pattern of river sand luminescence should show exponential-like decay in the headwaters which asymptotes to a constant value with further downstream distance. The parameters from the model can then be used to estimate the time-averaged virtual velocity, characteristic transport lengthscale, storage time scale, and floodplain exchange rate of fine sand-sized sediment in a fluvial system. The sediment transport values predicted from the luminescence method show a broader range than those reported in the literature, but the results are nonetheless encouraging and suggest that luminescence demonstrates potential as a sediment transport indicator. However, caution is warranted when applying the model as the complex nature of sediment transport can sometimes invalidate underlying simplifications.

Laboratory assessment of the mobility of water-dispersed engineered nanoparticles in a red soil (Ultisol)

NASA Astrophysics Data System (ADS)

Wang, Dengjun; Su, Chunming; Zhang, Wei; Hao, Xiuzhen; Cang, Long; Wang, Yujun; Zhou, Dongmei

2014-11-01

Soils are major sinks of engineered nanoparticles (ENPs) as results of land applications of sewage sludge, accidental spills, or deliberate applications of ENPs (e.g., nano-pesticides). In this study, the transport behaviors of four widely used ENPs (i.e., titanium dioxide [TiO2], buckminsterfullerene [C60], single-walled carbon nanotube [SWNT], and elemental silver [Ag0]) were investigated in water-saturated columns packed with either a quartz sand, a red soil (Ultisol), or sand/soil mixtures with soil mass fraction (λ) from 0% to 100% at slightly acidic solution pH (4.0-5.0). The mobility of tested ENPs decreased significantly with increasing λ, which was attributed to increased surface area and/or retention sites imparted by iron oxides, clay minerals, and organic matter in the red soil. Breakthrough curves of all ENPs exhibited blocking effects (decreasing deposition rate over time) and were well-described using an unfavorable and favorable, two-site kinetic attachment model accounting for random sequential adsorption on the favorable site. Modeled maximum retention capacity and first-order attachment rate coefficient on the favorable site both increased linearly with increasing λ, suggesting that transport parameters of ENPs in natural soils may be accurately extrapolated from transport parameters in the sand/soil mixtures. In addition, the mobility of three negatively charged ENPs (C60, SWNT, and Ag0 NPs) was reversely correlated with their average hydrodynamic diameters, highlighting that the average hydrodynamic diameter of negatively charged ENPs is the dominant physicochemical characteristics controlling their mobility in the Ultisol.

Effects of Monovalent and Divalent Salt Solutions on the Transport of Toxoplasma gondii in Saturated Porous Media

NASA Astrophysics Data System (ADS)

Darnault, C. J. G.; Pullano, C. P.; Mutty, T.; L'Ollivier, C.; Dubey, J. P.; Dumetre, A.

2017-12-01

The pathogenic microorganism Toxoplasma gondii is a current public health threat. Knowledge of the fate and transport of T. gondii in the environment, especially the subsurface, is critical to evaluate the risk of soil and groundwater contaminations. The physico-chemcial properties of groundwater systems, i.e. solution chemistry and aquifer materials, play a key role in the interaction of biocolloids with surfaces and therefore their mobility. This research examines how different salt solutions alter the mobility of T. gondii through saturated porous media. Salt solutions containing varying ionic strengths and concentrations of sodium chloride, calcium chloride, and magnesium chloride were used to test the transport of the T. gondii oocysts. These tests were performed using quartz silica sand columns fed by a peristaltic pump in order to generate flow and transport of the biocolloids. The salt solution was pumped though the column followed by a pulse of the T. gondii oocysts, then a pulse of salt solution without oocysts, and then lastly a pulse of distilled water. Sampling of the solution exiting the columns was tested for T. gondii oocysts using qPCR in order to quantify the oocysts present. The breakthough curve results were then compared to a conservative bromide tracer test in order to determine the factors associated with the movement of these biocolloids through the sand columns. A model of the flow of the toxoplasma colloids through the sand matrix was made in order to characterize the parameters affecting the transport and retention of T. gondii occysts though saturated porous media.

Sand petrology and focused erosion in collision orogens: the Brahmaputra case

NASA Astrophysics Data System (ADS)

Garzanti, Eduardo; Vezzoli, Giovanni; Andò, Sergio; France-Lanord, Christian; Singh, Sunil K.; Foster, Gavin

2004-03-01

The high-relief and tectonically active Himalayan range, characterized by markedly varying climate but relatively homogeneous geology along strike, is a unique natural laboratory in which to investigate several of the factors controlling the composition of orogenic sediments. Coupling of surface and tectonic processes is most evident in the eastern Namche Barwa syntaxis, where the Tsangpo-Siang-Brahmaputra River, draining a large elevated area in south Tibet, plunges down the deepest gorge on Earth. Here composition of river sands changes drastically from lithic to quartzofeldspathic. After confluence with the Lohit River, draining the Transhimalayan-equivalent Mishmi arc batholiths, sediment composition remains remarkably constant across Assam, indicating subordinate contributions from Himalayan tributaries. Independent calculations based on petrographical, mineralogical, and geochemical data indicate that the syntaxis, representing only ∼4% of total basin area, contributes 35±6% to the total Brahmaputra sediment flux, and ∼20% of total detritus reaching the Bay of Bengal. Such huge anomalies in erosion patterns have major effects on composition of orogenic sediments, which are recorded as far as the Bengal Fan. In the Brahmaputra basin, in spite of very fast erosion and detrital evacuation, chemical weathering is not negligible. Sand-sized carbonate grains are dissolved partially in mountain reaches and completely in monsoon-drenched Assam plains, where clinopyroxenes are selectively altered. Plagioclase, instead, is preferentially weathered only in detritus from the Shillong Plateau, which is markedly enriched in microcline. Most difficult to assess is the effect of hydraulic sorting in Bangladesh, where quartz, garnet and epidote tend to be sequestered in the bedload and trapped on the coastal plain, whereas cleavable feldspars and amphiboles are concentrated in the suspended load and eventually deposited in the deep sea. High-resolution petrographic and dense-mineral studies of fluvial sands provide a basis for calculating sediment budgets, for tracing patterns of erosion in mountain belts, and for better understanding the complex dynamic feedback between surface processes and crustal-scale tectonics.

A modeling study of the long-term mineral trapping in deep saline marine sands aquifers (Invited)

NASA Astrophysics Data System (ADS)

Aagaard, P.; Pham, V.; Hellevang, H.

2009-12-01

Simulation of geochemical processes due to CO2 injection and storage are dependent on sediment petrography and the kinetics of mineral fluid reactions. Mineral trapping of CO2 in the Utsira sand and similar marine sand reservoirs have been revisited based on critical review of rate data and geochemical constraints on formation waters. Reaction paths calculations were done with the PHREEQC modeling software at relevant reservoir conditions covering a temperature range of 30-100 °C and corresponding reservoir pressures. Initial CO2 saturation was determined by the fluid fugacity corresponding with reservoir conditions. The mineral dissolution kinetics was expressed with a chemical affinity term (Aagaard & Helgeson,1982) while a critical super-saturation for mineral growth was included in the precipitation rate expression. The redox conditions and the H2S fugacity in the simulations were constrained by the acetic/propionic acid buffer trend and the magnetite-pyrite buffer (Aagaard et al. 2001) respectively. We used a revised mineralogical composition for the Utsira sand also performed a sensitivity analyses with respect to mineral content. The simulations were run over a period of 10000 years. The main simulation results included dissolution of glauconite, smectite, pyrite, muscovite and albite, with precipitation of the carbonates siderite, ankerite, and minor dawsonite, as well as kaolinite, silica (either chalcedony or quartz), and K-feldspar. The uncertainties in the simulations are specially connected with initial mineral abundances. The effect of critical super-saturation and reactive surface area for precipitation needs to be further evaluated and tested. Aagaard, P. and H.C. Helgeson (1982). Thermodynamic and Kinetic Constraints on Reaction Rates among Minerals and Aqueous Solutions. I. Theoretical Considerations. Am. J. Sci., v. 282, p. 257-285. P. Aagaard, J. Jahren & S.N. Ehrenberg (2001) H2S controling reactions in clastic hydrocarbon reservoirs from the Norwegian Shelf and Gulf Coast, in Cidu, R.(ed) Water-Rock Interaction, WRI-10, Balkema, p. 129-132.

Properties of Desert Sand and CMAS Glass

NASA Technical Reports Server (NTRS)

Bansal, Narottam P.; Choi, Sung R.

2014-01-01

As-received desert sand from a Middle East country has been characterized for its phase composition and thermal stability. X-ray diffraction analysis showed the presence of quartz (SiO2), calcite (CaCO3), gypsum (CaSO4.2H2O), and NaAlSi3O8 phases in as-received desert sand and showed weight loss of approx. 35 percent due to decomposition of CaCO3 and CaSO4.2H2O when heated to 1400 C. A batch of as-received desert sand was melted into calcium magnesium aluminosilicate (CMAS) glass at approx. 1500 C. From inductively coupled plasma-atomic emission spectrometry, chemical composition of the CMAS glass was analyzed to be 27.8CaO-4MgO-5Al2O3-61.6SiO2-0.6Fe2O3-1K2O (mole percent). Various physical, thermal and mechanical properties of the glass have been evaluated. Bulk density of CMAS glass was 2.69 g/cc, Young's modulus 92 GPa, Shear modulus 36 GPa, Poisson's ratio 0.28, dilatometric glass transition temperature (T (sub g)) 706 C, softening point (T (sub d)) 764 C, Vickers microhardness 6.3 +/- 0.4 GPa, indentation fracture toughness 0.75 +/- 0.15 MPa.m (sup 1/2), and coefficient of thermal expansion (CTE) 9.8 x 10 (exp -6)/degC in the temperature range 25 to 700 C. Temperature dependence of viscosity has also been estimated from various reference points of the CMAS glass using the Vogel-Fulcher-Tamman (VFT) equation. The glass remained amorphous after heat treating at 850 C for 10 hr but crystallized into CaSiO3 and Ca-Mg-Al silicate phases at 900 C or higher temperatures. Crystallization kinetics of the CMAS glass has also been investigated by differential thermal analysis (DTA). Activation energies for the crystallization of two different phases in the glass were calculated to be 403 and 483 kJ/mol, respectively.

Clogging of an Alpine streambed by silt-sized particles - Insights from laboratory and field experiments.

PubMed

Fetzer, Jasmin; Holzner, Markus; Plötze, Michael; Furrer, Gerhard

2017-12-01

Clogging of streambeds by suspended particles (SP) can cause environmental problems, as it can negatively influence, e.g., habitats for macrozoobenthos, fish reproduction and groundwater recharge. This especially applies in the case of silt-sized SP. Until now, most research has dealt with coarse SP and was carried out in laboratory systems. The aims of this study are to examine (1) whether physical clogging by silt-sized SP exhibits the same dynamics and patterns as by sand-sized SP, and (2) the comparability of results between laboratory and field experiments. We carried out vertical column experiments with sand-sized bed material and silt-sized SP, which are rich in mica minerals. In laboratory experiments, we investigated the degree of clogging quantified by the reduction of porosity and hydraulic conductivity and the maximum clogging depth as a function of size and shape of bed material, size of SP, pore water flow velocity, and concentration of calcium cations. The SP were collected from an Alpine sedimentation basin, where our field experiments were carried out. To investigate the clogging process in the field, we buried columns filled with sand-sized quartz in the stream bed. We found that the maximal bed-to-grain ratio where clogging still occurs is larger for silt-sized SP than for sand-sized SP. The observed clogging depths and the reduction of flow rate through the column from our laboratory experiments were comparable to those from the field. However, our field results showed that the extent of clogging strongly depends on the naturally-occurring hydrological dynamics. The field location was characterized by a more polydisperse suspension, a strongly fluctuating water regime, and high SP concentrations at times, leading to more heterogeneous and more pronounced clogging when compared to laboratory results. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Ultrapure Water System for Hemodialysis Therapy

ClinicalTrials.gov

2011-07-21

The Change of Biomarkers CRP, CBC With the Use of Ultra Pure Water System for; Hemodialysis.; The Rate of Adverse Events Such as Hypotension During Hemodialysis Therapy With Ultra Pure Water; System as Compared to Conventional Water System.

INTERACTION OF LASER RADIATION WITH MATTER: Influence of Ca and Pb impurities on the bulk optical strength of ultrapure NaCl and KCl crystals

NASA Astrophysics Data System (ADS)

Vinogradov, An V.; Voszka, R.; Kovalev, Valerii I.; Faĭzullov, F. S.; Janszky, J.

1987-06-01

A significant increase (by a factor of about 3) of the bulk damage threshold in the case of interaction of CO2 laser radiation pulses with ultrapure NaCl and KCl crystals grown in a reactive atmosphere was observed on introduction of divalent metal ions Ca and Pb in concentrations of 10-5-10-6 mol/mol. Impurities were introduced in concentrations of 10-8-10-3 and 2×10-7-10-4 mol/mol into the melts of KCl and NaCl, respectively. The concentration of other impurities (including OH) did not exceed ~10-6 mol/mol. A physical model was developed to account for the observed dependence on the basis of an analogy between a system of colloidal particles and F centers in a crystal and a liquid-vapor system.

Cytocompatibility evaluation of gum Arabic-coated ultra-pure boron nitride nanotubes on human cells.

PubMed

Ciofani, Gianni; Del Turco, Serena; Rocca, Antonella; de Vito, Giuseppe; Cappello, Valentina; Yamaguchi, Maho; Li, Xia; Mazzolai, Barbara; Basta, Giuseppina; Gemmi, Mauro; Piazza, Vincenzo; Golberg, Dmitri; Mattoli, Virgilio

2014-05-01

Boron nitride nanotubes (BNNTs) are tubular nanoparticles with a structure analogous to that of carbon nanotubes, but with B and N atoms that completely replace the C atoms. Many favorable results indicate BNNTs as safe nanomaterials; however, important concerns have recently been raised about ultra-pure, long (~10 µm) BNNTs tested on several cell types. Here, we propose additional experiments with the same BNNTs, but shortened (~1.5 µm) with a homogenization/sonication treatment that allows for their dispersion in gum Arabic aqueous solutions. Obtained BNNTs are tested on human endothelial and neuron-like cells with several independent biocompatibility assays. Moreover, for the first time, their strong sum-frequency generation signal is exploited to assess the cellular uptake. Our data demonstrate no toxic effects up to concentrations of 20 µg/ml, once more confirming biosafety of BNNTs, and again highlighting that nanoparticle aspect ratio plays a key role in the biocompatibility evaluation.

Low background materials and fabrication techniques for cables and connectors in the Majorana Demonstrator

DOE PAGES

Busch, M.; Abgrall, N.; Alvis, S. I.; ...

2018-01-03

Here, the Majorana Collaboration is searching for the neutrinoless double-beta decay of the nucleus 76Ge. The Majorana Demonstrator is an array of germanium detectors deployed with the aim of implementing background reduction techniques suitable for a tonne scale 76Ge-based search (the LEGEND collaboration). In the Demonstrator, germanium detectors operate in an ultra-pure vacuum cryostat at 80 K. One special challenge of an ultra-pure environment is to develop reliable cables, connectors, and electronics that do not significantly contribute to the radioactive background of the experiment. This paper highlights the experimental requirements and how these requirements were met for the Majorana Demonstrator,more » including plans to upgrade the wiring for higher reliability in the summer of 2018. Also described are requirements for LEGEND R&D efforts underway to meet these additional requirements« less

Ultra-pure soft water ameliorates atopic skin disease by preventing metallic soap deposition in NC/Tnd mice and reduces skin dryness in humans.

PubMed

Tanaka, Akane; Matsuda, Akira; Jung, Kyungsook; Jang, Hyosun; Ahn, Ginnae; Ishizaka, Saori; Amagai, Yosuke; Oida, Kumiko; Arkwright, Peter D; Matsuda, Hiroshi

2015-09-01

Mineral ions in tap water react with fatty acids in soap, leading to the formation of insoluble precipitate (metallic soap) on skin during washing. We hypothesised that metallic soap might negatively alter skin conditions. Application of metallic soap onto the skin of NC/Tnd mice with allergic dermatitis further induced inflammation with elevation of plasma immunoglobulin E and proinflammatory cytokine expression. Pruritus and dryness were ameliorated when the back of mice was washed with soap in Ca2+- and Mg2+-free ultra-pure soft water (UPSW). Washing in UPSW, but not tap water, also protected the skin of healthy volunteers from the soap deposition. Furthermore, 4 weeks of showering with UPSW reduced dryness and pruritus of human subjects with dry skin. Washing with UPSW may be therapeutically beneficial in patients with skin troubles.

Oscillatory bedload transport: Data review and simple formulation

NASA Astrophysics Data System (ADS)

Hallermeier, Robert J.

1982-11-01

This review displays over 700 rates of sediment transport by oscillatory flow from 20 sources. Sediments include fine sands to pebbles, both of quartz and of lightweight materials, and the transport rates in water range over seven orders of magnitude. Most data are average gross (to and fro) bedload rates collinear with laboratory flow over a horizontal sediment bed, although other situations with net transport, suspended load, or oblique field waves are considered. As peak flow velocity nears twice the threshold velocity for sediment motion, bedload appears to be fully developed and the transport rate is near that given by a simple formula including flow frequency and peak velocity, and sediment size and density. At lesser peak velocities, bedload rates are markedly smaller and distinctly different regimes of sediment mobilization and transport may be identified.

A Large Lunar Surface Testbed from Low Cost Material

NASA Technical Reports Server (NTRS)

Rickman, Douglas

2014-01-01

For users needing to simulate the lunar surface, several distinct avenues have been used. Numerous volcanic areas, including Hawaii, have been used. While providing very large areas and scenic interest, field parties to such an area is expensive and limits testing time. An alternative is to build test facilities locally. This has been done many ways, contrast GRC-1, GSC-1, BP-1 and the KSC Morpheus facility [1-4]. GRC-1 is a mixture of sand and clay; GSC-1 and BP-1 are waste materials created in the process of crushing basaltic rock. The Morpheus field used salvaged concrete and crushed quartz rock [5]. Here I report about a 30 m X 30 m test area at MSFC which was both low cost and relatively high fidelity [6].

The regulation of crystalline silica: an industry perspective.

PubMed

Elzea, J M

1997-01-01

Silica is ubiquitous in the earth's crust. It occurs in trace to large quantities in rocks and soil. Because it is so common, the regulation of silica has affected a large number of industries, including the mining industry and any industry that uses quartz in the manufacture of a products. Mineral commodities that contain silica include diatomite, bentonite, kaolinite, talc, pyrophyllite, sand and gravel, perlite, pumice, dimension stone, and barite. Products that contain minerals, many of which are associated with silica, include paint, paper, rubber, plastic, pharmaceuticals, food, cement, plaster, cat litter, potting soil, plaster board, and miscellaneous construction materials. In collaboration with some agencies and academic centers, the silica industry is supporting research to lower health risks and to improve the methods of detecting this common material.

Effect of natural aquatic humic substances on the photodegradation of estrone.

PubMed

Silva, Carla Patrícia; Lima, Diana L D; Groth, Milena B; Otero, Marta; Esteves, Valdemar I

2016-02-01

Photodegradation of estrone (E1) was investigated under simulated solar radiation in absence and presence of the different fractions of humic substances (HS), namely humic acids (HA), fulvic acids (FA) and XAD-4 fraction. The pseudo-first order photodegradation rate constants increased from 0.1137 h(-1), in ultrapure (MQ) water, to 0.1774, 0.1943 and 0.3109 h(-1), in presence of HA, FA and XAD-4, respectively. Half-life time decreased from 6.10 h in MQ water to 3.91, 3.57 and 2.23 h in presence of HA, FA and XAD-4, respectively. These results evidence the relevant photosensitizing effect of XAD-4 fraction of HS on the degradation of E1, which, to the best of our knowledge have never been studied. Photodegradation studies were also conducted in organic matter-rich environmental aquatic matrices, namely fresh, estuarine and waste water. After 2 h, photodegradation achieved values ranged between 35.6 and 57.1% in natural water samples, compared with 26.4% in ultrapure water. The higher photodegradation occurred in an estuarine water sample, known to be rich in XAD-4 fraction and poor in HA, indicating that not only the presence of organic matter, but also its type, are determinant in the E1 photodegradation rate. Finally, the use of sodium azide as singlet oxygen ((1)O2) scavenger during the phototransformation of E1 in ultrapure and in two wastewater samples allowed to conclude that (1)O2 has an important role in the E1 photodegradation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Degradation of progestagens by oxidation with potassium permanganate in wastewater effluents.

PubMed

Fayad, Paul B; Zamyadi, Arash; Broseus, Romain; Prévost, Michèle; Sauvé, Sébastien

2013-01-01

This study investigated the oxidation of selected progestagenic steroid hormones by potassium permanganate at pH 6.0 and 8.0 in ultrapure water and wastewater effluents, using bench-scale assays. Second order rate constants for the reaction of potassium permanganate with progestagens (levonorgestrel, medroxyprogesterone, norethindrone and progesterone) was determined as a function of pH, presence of natural organic matter and temperature. This work also illustrates the advantages of using a novel analytical method, the laser diode thermal desorption (LDTD-APCI) interface coupled to tandem mass spectrometry apparatus, allowing for the quick determination of oxidation rate constants and increasing sample throughput. The second-order rate constants for progestagens with permanganate determined in bench-scale experiments ranged from 23 to 368 M(-1) sec(-1) in both wastewater and ultrapure waters with pH values of 6.0 and 8.0. Two pairs of progestagens exhibited similar reaction rate constants, i.e. progesterone and medroxyprogesterone (23 to 80 M(-1) sec(-1) in ultrapure water and 26 to 149 M(-1) sec(-1) in wastewaters, at pH 6.0 and 8.0) and levonorgestrel and norethindrone (179 to 224 M(-1) sec(-1) in ultrapure water and 180 to 368 M(-1) sec(-1) in wastewaters, at pH 6.0 and 8.0). The presence of dissolved natural organic matter and the pH conditions improved the oxidation rate constants for progestagens with potassium permanganate only at alkaline pH. Reaction rates measured in Milli-Q water could therefore be used to provide conservative estimates for the oxidation rates of the four selected progestagens in wastewaters when exposed to potassium permanganate. The progestagen removal efficiencies was lower for progesterone and medroxyprogesterone (48 to 87 %) than for levonorgestrel and norethindrone (78 to 97%) in Milli-Q and wastewaters at pH 6.0-8.2 using potassium permanganate dosages of 1 to 5 mg L(-1) after contact times of 10 to 60 min. This work presents the first results on the permanganate-promoted oxidation of progestagens, as a function of pH, temperature as well as NOM. Progestagen concentrations used to determine rate constants were analyzed using an ultrafast laser diode thermal desorption interface coupled to tandem mass spectrometry for the analysis of water sample for progestagens.

Qualitative and quantitative changes in detrital reservoir rocks caused by CO2-brine-rock interactions during first injection phases (Utrillas sandstones, Northern Spain)

NASA Astrophysics Data System (ADS)

Berrezueta, E.; Ordóñez-Casado, B.; Quintana, L.

2015-08-01

The aim of this article is to describe and interpret qualitative and quantitative changes at rock matrix scale of Lower-Upper Cretaceous sandstones exposed to supercritical (SC) CO2 and brine. The effects of experimental injection of SC CO2 during the first injection phases were studied at rock matrix scale, in a potential deep sedimentary reservoir in Northern Spain (Utrillas unit, at the base of the Cenozoic Duero Basin). Experimental wet CO2 injection was performed in a reactor chamber under realistic conditions of deep saline formations (P ≈ 78 bar, T ≈ 38 °C and 24 h exposure time). After the experiment, exposed and non-exposed equivalent sample sets were compared with the aim of assessing possible changes due to the effect of the CO2-brine exposure. Optical microscopy (OpM) and scanning electron microscopy (SEM) aided by optical image analysis (OIA) were used to compare the rock samples and get qualitative and quantitative information about mineralogy, texture and porous network distribution. Chemical analyses were performed to refine the mineralogical information and to obtain whole rock geochemical data. Brine composition was also analysed before and after the experiment. The results indicate an evolution of the pore network (porosity increase ≈ 2 %). Intergranular quartz matrix detachment and partial removal from the rock sample (due to CO2 input/release dragging) are the main processes that may explain the porosity increase. Primary mineralogy (≈ 95 % quartz) and rock texture (heterogeneous sand with interconnected framework of micro-channels) are important factors that seem to enhance textural/mineralogical changes in this heterogeneous system. The whole rock and brine chemical analyses after interaction with SC CO2-brine do not present important changes in the mineralogical, porosity and chemical configuration of the rock with respect to initial conditions, ruling out relevant precipitation or dissolution at these early stages. These results, simulating the CO2 injection near the injection well during the first phases (24 h) indicate that, in this environment where CO2 displaces the brine, the mixture principally generates local mineralogical/textural re-adjustments due to physical detachment of quartz grains. Consequences deriving from these changes are variable. Possible porosity and permeability increases could facilitate further CO2 injection but textural re-adjustment could also affect the rock physically. However, it is not clear yet what effect the quartz (solid suspension) could provoke in more distant areas of the rock. Quartz could be transported in the fluid flow path and probably accumulated at pore throats.

Mineralogical Characterization of the Miocene Olcese Formation, Southern San Joaquin Valley, California

NASA Astrophysics Data System (ADS)

Lopez, K. A.; Baron, D.; Guo, J.; Woolford, J. M.

2016-12-01

The early to middle Miocene Olcese Formation in the southern San Joaquin Valley of California consists of shallow marine shelf sands in its lower and upper parts, and non-marine, frequently pumiceous sands in its middle part, and varies in thickness up to 1800 ft. There is little known as to the origin, nature, quantity, and distribution of clay minerals throughout the formation. This study examined 95 sidewall core samples from three wells, as well as 388 cutting samples from four wells and 12 samples from 3 outcrops. Well samples were from depths between 1,800 and 4,000 ft. Qualitative and quantitative mineralogy including clay minerals of the sidewall samples and selected cutting samples was determined by powder X-ray diffraction (XRD). XRD analyses were supplemented by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) and petrographic microscopy of selected samples. The main minerals of bulk samples include composite clay, quartz, potassium feldspar/plagioclase, calcite, and clinoptilolite. Content of composite clay varies between 17% and 51%. The clay-size fraction is predominantly composed of smectite, illite, kaolinite and chlorite with smectite being the most abundant. Smectite and clinoptilolite may be the alteration products of deeper burial of volcanic materials. The formation permeability could be significantly lowered by these authigenic minerals.

Graphene oxide-facilitated transport of levofloxacin and ciprofloxacin in saturated and unsaturated porous media.

PubMed

Sun, Kaixuan; Dong, Shunan; Sun, Yuanyuan; Gao, Bin; Du, Wenchao; Xu, Hongxia; Wu, Jichun

2018-04-15

In this work, effects of graphene oxide (GO) on the co-transport of the two typical Fluoroquinolones (FQs) - levofloxacin (LEV) and ciprofloxacin (CIP) in saturated and unsaturated quartz sand media were studied. The adsorption isotherms showed that GO had much larger sorption capacities to LEV and CIP than sand with the largest Langmuir adsorption capacity of 409 mg g -1 (CIP-GO); while the sorption affinity of the two FQs onto the two adsorbents might follow the order of CIP-sand > LEV-sand > LEV-GO > CIP-GO. GO promoted the mobility of the two FQs in both saturated and unsaturated porous media due to its strong mobility and sorption capacity. The GO-bound LEV/CIP was responsible for the LEV/CIP transport in the porous media, and transport of GO-bound FQs increased with the increasing of initial GO concentration. Under unsaturated conditions, moisture showed little effect on the transport of GO-bound CIP; however, the mobility of GO-bound LEV reduced with the decreasing of moisture content, suggesting the transport of adsorbed LEV from GO to air-water interface. GO sorption reduced the antibacterial ability of the two FQs, but they were still effective in inhibiting E. coli growth. Copyright © 2018 Elsevier B.V. All rights reserved.

Impact of Fish Farming on Phosphorus in Reservoir Sediments

PubMed Central

Jia, Binyang; Tang, Ya; Tian, Liyan; Franz, Leander; Alewell, Christine; Huang, Jen-How

2015-01-01

Fish farming has seriously influenced the aquatic environment in Sancha reservoir in SW China since 1985 and has been strongly restricted since 2005. Thus, phosphorus speciation in a sediment core dated between 1945 and 2010 at cm-resolution and in surface sediments from Sancha reservoir may allow us track how fish farming impacts phosphorus dynamics in lake sediments. Fish farming shifts the major binding forms of phosphorus in sediments from organic to residual phosphorus, which mostly originated from fish feed. Sorption to metal oxides and association with organic matters are important mechanisms for phosphorus immobilisation with low fish farming activities, whereas calcium-bound phosphorous had an essential contribution to sediment phosphorus increases under intensive fish framing. Notwithstanding the shifting, the aforementioned phosphorus fractions are usually inert in the lake environment, therefore changing phosphorus mobility little. The use of fish feed and water-purification reagents, the most important additives for fish farming, introduce not only phosphorus but also large amounts of sand-sized minerals such as quartz into the lake, to which phosphorus weakly sorbs. The sand-sized minerals as additional sorbents increase the pool of easily mobilisable phosphorus in sediments, which will slow down the recovery of reservoir water due to its rapid re-mobilisation. PMID:26577441

Transport of Escherichia coli in 25 m quartz sand columns

NASA Astrophysics Data System (ADS)

Lutterodt, G.; Foppen, J. W. A.; Maksoud, A.; Uhlenbrook, S.

2011-01-01

To help improve the prediction of bacteria travel distances in aquifers laboratory experiments were conducted to measure the distant dependent sticking efficiencies of two low attaching Escherichia coli strains (UCFL-94 and UCFL-131). The experimental set up consisted of a 25 m long helical column with a diameter of 3.2 cm packed with 99.1% pure-quartz sand saturated with a solution of magnesium sulfate and calcium chloride. Bacteria mass breakthrough at sampling distances ranging from 6 to 25.65 m were observed to quantify bacteria attachment over total transport distances ( αL) and sticking efficiencies at large intra-column segments ( αi) (> 5 m). Fractions of cells retained ( Fi) in a column segment as a function of αi were fitted with a power-law distribution from which the minimum sticking efficiency defined as the sticking efficiency of 0.001% bacteria fraction of the total input mass retained that results in a 5 log removal were extrapolated. Low values of αL in the order 10 - 4 and 10 - 3 were obtained for UCFL-94 and UCFL-131 respectively, while αi-values ranged between 10 - 6 to 10 - 3 for UCFL-94 and 10 - 5 to 10 - 4 for UCFL-131. In addition, both αL and αi reduced with increasing transport distance, and high coefficients of determination (0.99) were obtained for power-law distributions of αi for the two strains. Minimum sticking efficiencies extrapolated were 10 - 7 and 10 - 8 for UCFL-94 and UCFL-131, respectively. Fractions of cells exiting the column were 0.19 and 0.87 for UCFL-94 and UCL-131, respectively. We concluded that environmentally realistic sticking efficiency values in the order of 10 - 4 and 10 - 3 and much lower sticking efficiencies in the order 10 - 5 are measurable in the laboratory, Also power-law distributions in sticking efficiencies commonly observed for limited intra-column distances (< 2 m) are applicable at large transport distances(> 6 m) in columns packed with quartz grains. High fractions of bacteria populations may possess the so-called minimum sticking efficiency, thus expressing their ability to be transported over distances longer than what might be predicted using measured sticking efficiencies from experiments with both short (< 1 m) and long columns (> 25 m). Also variable values of sticking efficiencies within and among the strains show heterogeneities possibly due to variations in cell surface characteristics of the strains. The low sticking efficiency values measured express the importance of the long columns used in the experiments and the lower values of extrapolated minimum sticking efficiencies makes the method a valuable tool in delineating protection areas in real-world scenarios.

Experimental study on impact-induced seismic wave propagating through quartz sand simulating asteroid regolith

NASA Astrophysics Data System (ADS)

Matsue, Kazuma; Arakawa, Masahiko; Yasui, Minami; Matsumoto, Rie; Tsujido, Sayaka; Takano, Shota; Hasegawa, Sunao

2015-08-01

Introduction: Recent spacecraft surveys clarified that asteroid surfaces were covered with regolith made of boulders and pebbles such as that found on the asteroid Itokawa. It was also found that surface morphologies of asteroids formed on the regolith layer were modified. For example, the high-resolution images of the asteroid Eros revealed the evidence of the downslope movement of the regolith layer, then it could cause the degradation and the erasure of small impact crater. One possible process to explain these observations is the regolith layer collapse caused by seismic vibration after projectile impacts. The impact-induced seismic wave might be an important physical process affecting the morphology change of regolith layer on asteroid surfaces. Therefore, it is significant for us to know the relationship between the impact energy and the impact-induced seismic wave. So in this study, we carried out impact cratering experiments in order to observe the seismic wave propagating through the target far from the impact crater.Experimental method: Impact cratering experiments were conducted by using a single stage vertical gas gun set at Kobe Univ and a two-stage vertical gas gun set at ISAS. We used quartz sands with the particle diameter of 500μm, and the bulk density of 1.48g/cm3. The projectile was a ball made of polycarbonate with the diameter of 4.75mm and aluminum, titan, zirconia, stainless steel, cupper, tungsten carbide projectile with the diameter of 2mm. These projectiles were launched at the impact velocity from 0.2 to 7km/s. The target was set in a vacuum chamber evacuated below 10 Pa. We measured the seismic wave by using a piezoelectric uniaxial accelerometer.Result: The impact-induced seismic wave was measured to show a large single peak and found to attenuate with the propagation distance. The maximum acceleration of the seismic wave was recognized to have a good relationship with the normalized distance x/R, where x is the propagation distance and R is the crater radius, irrespective of the impact velocities: gmax = 160(x/R)-2.98.

Ultrasonic investigation of granular materials subjected to compression and crushing.

PubMed

Gheibi, Amin; Hedayat, Ahmadreza

2018-07-01

Ultrasonic wave propagation measurement has been used as a suitable technique for studying the granular materials and investigating the soil fabric structure, the grain contact stiffness, frictional strength, and inter-particle contact area. Previous studies have focused on the variations of shear and compressional wave velocities with effective stress and void ratio, and lesser effort has been made in understanding the variation of amplitude and dominant frequency of transmitted compressional waves with deformation of soil packing. In this study, continuous compressional wave transmission measurements during compaction of unconsolidated quartz sand are used to investigate the impact of soil layer deformation on ultrasonic wave properties. The test setup consisted of a loading machine to apply constant loading rate to a sand layer (granular quartz) of 6 mm thickness compressed between two forcing blocks, and an ultrasonic wave measurement system to continuously monitor the soil layer during compression up to 48 MPa normal stress. The variations in compressional wave attributes such as wave velocity, transmitted amplitude, and dominant frequency were studied as a function of the applied normal stress and the measured normal strain as well as void ratio and particle size. An increasing trend was observed for P-wave velocity, transmitted amplitude and dominant frequency with normal stress. In specimen with the largest particle size (D 50  = 0.32 mm), the wave velocity, amplitude and dominant frequency were found to increase about 230%, 4700% and 320% as the normal stress reached the value of 48 MPa. The absolute values of transmitted wave amplitude and dominant frequency were greater for specimens with smaller particle sizes while the normalized values indicate an opposite trend. The changes in the transmitted amplitude were linked to the changes in the true contact area between the particles with a transitional point in the slope of normalized amplitude, coinciding with the yield stress of the granular soil layer. The amount of grain crushing as a result of increase in the normal stress was experimentally measured and a linear correlation was found between the degree of grain crushing and the changes in the normalized dominant frequency of compressional waves. Copyright © 2018 Elsevier B.V. All rights reserved.

The mobility of indium and gallium in groundwater systems: constraining the role of sorption in sand column experiments

NASA Astrophysics Data System (ADS)

Dror, I.; Ringering, K.; Yecheskel, Y.; Berkowitz, B.

2017-12-01

The mobility of indium and gallium in groundwater environments was studied via laboratory experiments using quartz sand as a porous medium. Indium and gallium are metals of very low abundance in the Earth's crust and, correspondingly, the biosphere is only adapted to very small concentrations of these elements. However, in modern semiconductor industries, both elements play a central role and are incorporated in devices of mass production such as smartphones and digital cameras. The resulting considerable increase in production, use and discharge of indium and gallium throughout the last two decades, with a continuous and fast increase in the near future, raises questions regarding the fate of both elements in the environment. However, the transport behavior of these two metals in soils and groundwater systems remains poorly understood to date. Because of the low solubility of both elements in aqueous solutions, trisodium citrate was used as a complexation agent to stabilize the solutions, enabling investigation of the transport of these metals at neutral pH. Column experiments showed different binding capacities for indium and gallium, where gallium is much more mobile compared to indium and both metals are substantially retarded in the column. Different affinities were also confirmed by examining sorption isotherms of indium and gallium in equilibrium batch systems. The effect of natural organic matter on the mobility of indium and gallium was also studied, by addition of humic acid. For both metals, the presence of humic acid affects the sorption dynamics: for indium, sorption is strongly inhibited leading to much higher mobility, whereas gallium showed a slightly higher sorption affinity and very similar mobility compared to the same setup without humic acid addition. However, in all cases, the binding capacity of gallium to quartz is much weaker than that of indium. These results are consistent with the assumption that indium and gallium form different types of complexes with organic ligands. It was further observed that the complexes of gallium appear to be more stable than those of indium.

Ball clay and bentonite deposits of the central and western Gulf of Mexico Coastal Plain, United States

USGS Publications Warehouse

Hosterman, John W.

1984-01-01

The Gulf of Mexico Coastal Plain produces approximately 85 percent of the ball clay used in the United States. The best commercial-grade clay deposits are composed of poorly crystalline kaolinite and small amounts of Md illite and (or) smectite. Sand and silt and iron oxide minerals are virtually absent, but quartz is present in the clay-size fraction. The best grade ball clays are found as lenses limited to the Wilcox Group (Paleocene and lower Eocene) and Claiborne Group (middle Eocene). Reserves of ball clay are sufficient for the present, but because of the lenticular nature of the clay bodies, close-spaced drilling, detailed sampling, mineralogic analyses, and ceramic testing are needed to prove future reserves.Approximately 11 percent of the total bentonite produced in the United States comes from the Gulf Coast region. The commercial-grade bentonites are composed primarily of smectite with little or no Md illite and kaolinite. The nonclay impurities are quartz, feldspar, muscovite, biotite, calcite, dolomite, gypsum, and heulandite. Commercial bentonites occur in the Upper Cretaceous formations in Alabama and Mississippi, in Paleocene formations in Mississippi and Tennessee, and in Eocene and Miocene formations in Texas. The demand for low-swelling bentonite of the Gulf Coastal Plain has not increased along with the demand for swelling bentonite; therefore the reserves are adequate.

Thermodynamic properties of methane hydrate in quartz powder.

PubMed

Voronov, Vitaly P; Gorodetskii, Evgeny E; Safonov, Sergey S

2007-10-04

Using the experimental method of precision adiabatic calorimetry, the thermodynamic (equilibrium) properties of methane hydrate in quartz sand with a grain size of 90-100 microm have been studied in the temperature range of 260-290 K and at pressures up to 10 MPa. The equilibrium curves for the water-methane hydrate-gas and ice-methane hydrate-gas transitions, hydration number, latent heat of hydrate decomposition along the equilibrium three-phase curves, and the specific heat capacity of the hydrate have been obtained. It has been experimentally shown that the equilibrium three-phase curves of the methane hydrate in porous media are shifted to the lower temperature and high pressure with respect to the equilibrium curves of the bulk hydrate. In these experiments, we have found that the specific heat capacity of the hydrate, within the accuracy of our measurements, coincides with the heat capacity of ice. The latent heat of the hydrate dissociation for the ice-hydrate-gas transition is equal to 143 +/- 10 J/g, whereas, for the transition from hydrate to water and gas, the latent heat is 415 +/- 15 J/g. The hydration number has been evaluated in the different hydrate conditions and has been found to be equal to n = 6.16 +/- 0.06. In addition, the influence of the water saturation of the porous media and its distribution over the porous space on the measured parameters has been experimentally studied.

Dust Fertilization of the Western Atlantic Biota: a Biochemical Model

NASA Astrophysics Data System (ADS)

Holmes, C. W.

2017-12-01

Every year an estimated 50 million tons of African dust reaches the Western Atlantic. This dust is composed of quartz sand, clay, and a mixture of quartz and clay particles agglutinated with micronutrient enriched ferruginous cement. However, whether it is friend or foe to biochemical systems is a matter of conjecture. Corals are ideal recorders of changing conditions as the layers can be dated so that the record of chemical changes is easily assessed. There is extensive shallow-and deep water coral development bordering the Florida Straits. The changes in trace element chemistry within these corals show a positive relationship with the African dust record. Recently, it has been demonstrated that many of the metals contained within the dust are necessary micronutrients in the fertilization of plankton. Using the results of these studies, a biochemical model has been constructed. This model suggests a path from inorganic dust through microbial transformation to micronutrient enzymes (i.e. Cd-enriched carbonic anahydrase) and carbonate precipitation on the Bahamian Banks. It is estimated that more than ten million metric tons of this fine, metal-rich sediment is formed each year. However, for much of this sediment, its deposition is temporary, as it is transported into the Florida Straits yearly by tropical cyclones. This metal-enriched fine carbonate becomes nutrients for phytoplankton, providing food for the corals, both shallow and deep.

Facies identification based on conventional core-log integration: Middle Ordovician St. Peter sandstone, Michigan basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wieczorek, L.M.; Barnes, D.A.

1989-08-01

Lithofacies comprising the massive sand in the Michigan basin are very similar to the lithofacies of the St. Peter Sandstone in parts of the adjacent Midwestern basin and arches region. Lithostratigraphic and biostratigraphic correlations justify application of the name St. Peter Sandstone to the gas-productive massive sand in the Michigan basin. Four lithofacies have been determined by core-log integration. The two lowermost lithofacies (1 and 2) were deposited in marginal-marine peritidal shoreface to sand-flat environments. Lithofacies 1A comprises cross-bedded, quartz-cemented quartzarenites. Lithofacies 1B comprises dolomitic, cross-bedded, subfeldspathic arenites. Lithofacies 1A is recognized in logs by low gamma-ray response (less thanmore » 20-25 API units) and photoelectric effect (Pe) of 1.8. Lithofacies 1B log characteristics include low gamma ray response (15-30 API units) and Pe of 2-2.5. Lithofacies 2 log signatures include moderate to high gamma-ray (30-120 API units) and Pe values that range from 2.5-3.5. The uppermost two lithofacies (3 and 4) were deposited in storm-dominated lower shoreface, to offshore, to distal marine shelf environments. Lithofacies 3 consists of burrowed, massive, wavy to planar stratified quartzarenites to subfeldspathic arenites. Log signature is generally low gamma-ray response (15-30 API units) and Pe that ranges from 1.8 to 2.5. Lithofacies 4 consists of massive, burrowed and bioturbated, dominantly authigenic clay and dolomite-cemented subfeldspathic arenite. Lithofacies 4 log response is moderate to high gamma-ray response (30-105 API units) and Pe ranging from 2.25 to 3.5.« less

Digital data sets that describe aquifer characteristics of the alluvial and terrace deposits along the North Canadian River from Canton Lake to Lake Overholser in Central Oklahoma

USGS Publications Warehouse

Adams, G.P.; Rea, Alan; Runkle, D.L.

1997-01-01

ARC/INFO export and nonproprietary format files This diskette contains digitized aquifer boundaries and maps of of hydraulic conductivity, recharge, and ground-water level elevation contours for the alluvial and terrace deposits along the alluvial and terrace deposits along the North Canadian River from Canton Lake to Lake Overholser in central Oklahoma. Ground water in approximately 400 square miles of Quaternary-age alluvial and terrace aquifer is an important source of water for irrigation, industrial, municipal, stock, and domestic supplies. The aquifer consists of clay, silt, sand, and gravel. Sand-sized sediments dominate the poorly sorted, fine to coarse, unconsolidated quartz grains in the aquifer. The hydraulically connected alluvial and terrace deposits unconformably overlie Permian-age formations. The aquifer is overlain by a layer of wind-blown sand in parts of the area. Most of the lines in the aquifer boundary, hydraulic conductivity, and recharge data sets were extracted from published digital surficial geology data sets based on a scale of 1:250,000. The ground-water elevation contours and some of the lines for the aquifer boundary, hydraulic conductivity, and recharge data sets were digitized from a ground-water modeling report about the aquifer published at a scale of 1:250,000. The hydraulic conductivity values and recharge rates also are from the ground-water modeling report. Ground-water flow models are numerical representations that simplify and aggregate natural systems. Models are not unique; different combinations of aquifer characteristics may produce similar results. Therefore, values of hydraulic conductivity and recharge used in the model and presented in this data set are not precise, but are within a reasonable range when compared to independently collected data.

Digital data sets that describe aquifer characteristics of the Elk City Aquifer in western Oklahoma

USGS Publications Warehouse

Becker, C.J.; Runkle, D.L.; Rea, Alan

1997-01-01

ARC/INFO export and nonproprietary format files This diskette contains digitized aquifer boundaries and maps of hydraulic conductivity, recharge, and ground-water level elevation contours for the Elk City aquifer in western Oklahoma. The aquifer covers an area of approximately 193,000 acres and supplies ground water for irrigation, domestic, and industrial purposes in Beckham, Custer, Roger Mills, and Washita Counties along the divide between the Washita and Red River basins. The Elk City aquifer consists of the Elk City Sandstone and overlying terrace deposits, made up of clay, silt, sand and gravel, and dune sands in the eastern part and sand and gravel of the Ogallala Formation (or High Plains aquifer) in the western part of the aquifer. The Elk City aquifer is unconfined and composed of very friable sandstone, lightly cemented with clay, calcite, gypsum, or iron oxide. Most of the grains are fine-sized quartz but the grain size ranges from clay to cobble in the aquifer. The Doxey Shale underlies the Elk City aquifer and acts as a confining unit, restricting the downward movement of ground water. All of the data sets were digitized and created from information and maps in a ground-water modeling thesis and report of the Elk City aquifer. The maps digitized were published at a scale of 1:63,360. Ground-water flow models are numerical representations that simplify and aggregate natural systems. Models are not unique; different combinations of aquifer characteristics may produce similar results. Therefore, values of hydraulic conductivity and recharge used in the model and presented in this data set are not precise, but are within a reasonable range when compared to independently collected data.

Time-Fractional Advection-Dispersion Equation (tFADE) to Quantify Aqueous Phase Contaminant Elution from a Trichloroethene (TCE) NAPL Source Zone in Sand Columns

NASA Astrophysics Data System (ADS)

Tick, G. R.; Wei, S.; Sun, H.; Zhang, Y.

2016-12-01

Pore-scale heterogeneity, NAPL distribution, and sorption/desorption processes can significantly affect aqueous phase elution and mass flux in porous media systems. The application of a scale-independent fractional derivative model (tFADE) was used to simulate elution curves for a series of columns (5 cm, 7 cm, 15 cm, 25 cm, and 80 cm) homogeneously packed with 20/30-mesh sand and distributed with uniform saturations (7-24%) of NAPL phase trichloroethene (TCE). An additional set of columns (7 cm and 25 cm) were packed with a heterogeneous distribution of quartz sand upon which TCE was emplaced by imbibing the immiscible liquid, under stable displacement conditions, to simulate a spill-type process. The tFADE model was able to better represent experimental elution behavior for systems that exhibited extensive long-term concentration tailing requiring much less parameters compared to typical multi-rate mass transfer models (MRMT). However, the tFADE model was not able to effectively simulate the entire elution curve for such systems with short concentration tailing periods since it assumes a power-law distribution for the dissolution rate for TCE. Such limitations may be solved using the tempered fractional derivative model, which can capture the single-rate mass transfer process and therefore the short elution concentration tailing behavior. Numerical solution for the tempered fractional-derivative model in bounded domains however remains a challenge and therefore requires further study. However, the tFADE model shows excellent promise for understanding impacts on concentration elution behavior for systems in which physical heterogeneity, non-uniform NAPL distribution, and pronounced sorption-desorption effects dominate or are present.

Geologic columns for the ICDP-USGS Eyreville B core, Chesapeake Bay impact structure: Impactites and crystalline rocks, 1766 to 1096 m depth

USGS Publications Warehouse

Horton, J. Wright; Gibson, R.L.; Reimold, W.U.; Wittmann, A.; Gohn, G.S.; Edwards, L.E.

2009-01-01

The International Continental Scientific Drilling Program (ICDP)-U.S. Geological Survey (USGS) Eyreville drill cores from the Chesapeake Bay impact structure provide one of the most complete geologic sections ever obtained from an impact structure. This paper presents a series of geologic columns and descriptive lithologic information for the lower impactite and crystalline-rock sections in the cores. The lowermost cored section (1766-1551 m depth) is a complex assemblage of mica schists that commonly contain graphite and fibrolitic sillimanite, intrusive granite pegmatites that grade into coarse granite, and local zones of mylonitic deformation. This basement-derived section is variably overprinted by brittle cataclastic fabrics and locally cut by dikes of polymict impact breccia, including several suevite dikes. An overlying succession of suevites and lithic impact breccias (1551-1397 m) includes a lower section dominated by polymict lithic impact breccia with blocks (up to 17 m) and boulders of cataclastic gneiss and an upper section (above 1474 m) of suevites and clast-rich impact melt rocks. The uppermost suevite is overlain by 26 m (1397-1371 m) of gravelly quartz sand that contains an amphibolite block and boulders of cataclasite and suevite. Above the sand, a 275-m-thick allochthonous granite slab (1371-1096 m) includes gneissic biotite granite, fine- and medium-to-coarse-grained biotite granites, and red altered granite near the base. The granite slab is overlain by more gravelly sand, and both are attributed to debris-avalanche and/or rockslide deposition that slightly preceded or accompanied seawater-resurge into the collapsing transient crater. ?? 2009 The Geological Society of America.

Concentration/time-dependent dissipation, partitioning and plant accumulation of hazardous current-used pesticides and 2-hydroxyatrazine in sand and soil.

PubMed

Neuwirthová, Natália; Bílková, Zuzana; Vašíčková, Jana; Hofman, Jakub; Bielská, Lucie

2018-07-01

The dissipation, partitioning dynamics and biouptake was measured for selected hazardous current-used pesticides (conazole fungicides: epoxiconazole, flusilazole, tebuconazole; prochloraz, chlorpyrifos, pendimethalin) and for a transformation product (2-hydroxyatrazine) in agricultural soil and quartz sand as representatives of a real and a worst-case scenario. Dissipation, uptake to Lactuca sativa and the freely dissolved concentration along with the organic carbon-normalized sorption coefficients (K oc ) were determined on days 12, 40, and 90 following the application of compounds at three fortification levels (0.1-1.0-10 mg/kg). Conazole fungicides showed similar dissipation patterns and were more persistent in soil than prochloraz, chlorpyrifos and pendimethalin. 2-Hydroxyatrazine showed a concentration-depended decrease in persistency in soil. Lettuce roots were shown to accumulate higher amounts than shoots where the extent of root uptake was driven by compound partitioning. This was evidenced by the ability of freely dissolved concentration (C free ) to reliably (r 2  = 0.94) predict root uptake. Concentration in leaves did not exceed the maximum residue levels (MRLs) for lettuce, which was likely given by the low root-to-shoot translocation factors (TFs) of the tested compounds varying between 0.007 and 0.14. K oc values were in the range of literature values. Sorption to soil was higher than to sand for all compounds, yet following the K oc dynamics compounds did not appear to be sequestered in soil with increasing residence time. From these results, it follows that the tested compounds may persist in soil but since they did not accumulate in lettuce above MRLs, contamination of the food web is unlikely. Copyright © 2018 Elsevier Ltd. All rights reserved.

Source-to-Sink System Evolution as Recorded in Clastic Facies in Two New Zealand Examples: the Bounty System of South Island and the Waipaoa System of North Island

NASA Astrophysics Data System (ADS)

Marsaglia, K. M.

2010-12-01

New Zealand river sources and their submarine sinks are excellent examples for modeling source-to-sink systems. In particular, the sand fractions of these systems can be used as tracers to document links and/or disconnects between fluvial, shelf, slope, and bathyal components. Within any given system, the ability to use sand as a tracer depends on the nature of the rocks exposed in source river drainage basins. In evolving systems, the potential for erosional unroofing, change of outcrop lithology through time, can be important. Additionally, the ability of a given lithology to generate sediment of a certain size may also vary. For example in the New Zealand examples, Cenozoic mudstones generate mostly mud but can liberate recycled sand grains (if present), as well as a smaller proportion of mudstone lithic fragments depending on degree of mudstone induration; schist generates copious sand and quartz-vein pebbles; and thin-bedded sandy turbidites can generate significant gravel, as well as mud and sand. Sediment production mode also comes into play with glacial processes (South Island) generating rock flour, as well as coarser debris. The major outcropping unit across both islands is a sedimentary to metasedimentary forearc succession, the Torlesse Terrane. It served as the protolith of the Otago schist (South Island) and the source of detritus for Cretaceous and Cenozoic sedimentary units on both islands. Local magmatism also supplied sand-sized material: intraplate (South Island) volcanism produced intrabasinal epiclastic debris and magmatic arc (North Island) volcanism produced extrabasinal pyroclastic debris. Various lithologies have characteristic detrital signatures. For example, in the Cenozoic units of the Waipaoa system, Pliocene calcareous mudstone fragments are key lithic components in tracing sediment transport from source-to sink, whereas the major fingerprint of Otago schist input into the Bounty System of South Island is mica. Critical to defining sedimentary budgets in both New Zealand systems is defining the net proportion of dip-fed vs. strike-fed clastic components. The former are supplied directly to the system by coast-perpendicular rivers, and the latter are transported into or out of the system by coast-parallel currents (e.g., longshore, shelf, slope). Tectonic events in the fluvial drainage basin can also have major influences on the supply of sediment to offshore basins. There is evidence for lacustrine sediment traps in each New Zealand system and evidence, in at least one case, that they modified sediment input to the marine part of the system (Bounty Fan).

ISOLATION AND IDENTIFICATION OF NONTUBERCULOUS MYCOBACTERIA FROM FOODS AS POSSIBLE EXPOSURE SOURCES

EPA Science Inventory

A variety of foods collected from local supermarkets and produce stands were examined as possible sources of nontuberculous mycobacterial exposure. Food samples were combined with sterile ultrapure water and manually shaken. To remove large particles, the suspensions were filtere...

Enhancement of OVA-induced murine lung eosinophilia by co-exposure to contamination levels of LPS in Asian sand dust and heated dust

PubMed Central

2014-01-01

Background A previous study has shown that the aggravation of Asian sand dust (ASD) on ovalbumin (OVA)-induced lung eosinphilia was more severe in lipopolysaccharide (LPS)-rich ASD than in SiO2-rich ASD. Therefore, the effects of different LPS contamination levels in ASD on the aggravation of OVA-induced lung eosinophilia were investigated in the present study. Methods Before beginning the in vivo experiment, we investigated whether the ultra-pure LPS would act only on TLR4 or not using bone marrow-derived macrophages (BMDMs) of wild–type, TLR2-/-, TLR4-/- and MyD88-/- BALB/c mice. ASD collected from the desert was heated to remove toxic organic substances (H-ASD). BALB/c mice were instilled intratracheally with 12 different testing samples prepared with LPS (1 ng and 10 ng), H-ASD, and OVA in a normal saline solution. The lung pathology, cytological profiles in the bronchoalveolar lavage fluid (BALF), the levels of inflammatory cytokines/chemokines in BALF and OVA-specific immunoglobulin in serum were investigated. Results The LPS exhibited no response to the production of TNF-α and IL-6 in BMDMs from TLR4-/-, but did from TLR2-/-. H-ASD aggravated the LPS-induced neutrophilic lung inflammation. In the presence of OVA, LPS increased the level of eosinophils slightly and induced trace levels of Th2 cytokines IL-5 and IL-13 at the levels of 1 ng and 10 ng. In the presence of OVA and H-ASD, LPS induced severe eosinophil infiltration and proliferation of goblet cells in the airways as well as remarkable increases in Th2 cytokines IL-5 and IL-13 in BALF. The mixture containing LPS (1 ng) showed adjuvant activity on OVA-specific IgE and IgG1 production. Conclusions The results suggest that H-ASD with naturally-occurring levels of LPS enhances OVA-induced lung eosinophilia via increases in Th2-mediated cytokines and antigen-specific immunoglobulin. These results indicate that LPS is a strong candidate for being a major aggravating substance in ASD. PMID:24982682

Enhancement of OVA-induced murine lung eosinophilia by co-exposure to contamination levels of LPS in Asian sand dust and heated dust.

PubMed

Ren, Yahao; Ichinose, Takamichi; He, Miao; Song, Yuan; Yoshida, Yasuhiro; Yoshida, Seiichi; Nishikawa, Masataka; Takano, Hirohisa; Sun, Guifan; Shibamoto, Takayuki

2014-01-01

A previous study has shown that the aggravation of Asian sand dust (ASD) on ovalbumin (OVA)-induced lung eosinphilia was more severe in lipopolysaccharide (LPS)-rich ASD than in SiO2-rich ASD. Therefore, the effects of different LPS contamination levels in ASD on the aggravation of OVA-induced lung eosinophilia were investigated in the present study. Before beginning the in vivo experiment, we investigated whether the ultra-pure LPS would act only on TLR4 or not using bone marrow-derived macrophages (BMDMs) of wild-type, TLR2-/-, TLR4-/- and MyD88-/- BALB/c mice. ASD collected from the desert was heated to remove toxic organic substances (H-ASD). BALB/c mice were instilled intratracheally with 12 different testing samples prepared with LPS (1 ng and 10 ng), H-ASD, and OVA in a normal saline solution. The lung pathology, cytological profiles in the bronchoalveolar lavage fluid (BALF), the levels of inflammatory cytokines/chemokines in BALF and OVA-specific immunoglobulin in serum were investigated. The LPS exhibited no response to the production of TNF-α and IL-6 in BMDMs from TLR4-/-, but did from TLR2-/-. H-ASD aggravated the LPS-induced neutrophilic lung inflammation. In the presence of OVA, LPS increased the level of eosinophils slightly and induced trace levels of Th2 cytokines IL-5 and IL-13 at the levels of 1 ng and 10 ng. In the presence of OVA and H-ASD, LPS induced severe eosinophil infiltration and proliferation of goblet cells in the airways as well as remarkable increases in Th2 cytokines IL-5 and IL-13 in BALF. The mixture containing LPS (1 ng) showed adjuvant activity on OVA-specific IgE and IgG1 production. The results suggest that H-ASD with naturally-occurring levels of LPS enhances OVA-induced lung eosinophilia via increases in Th2-mediated cytokines and antigen-specific immunoglobulin. These results indicate that LPS is a strong candidate for being a major aggravating substance in ASD.

Aquifer modification: an approach to improve the mobility of nanoscale zero-valent iron particles used for in situ groundwater remediation

NASA Astrophysics Data System (ADS)

MicicBatka, Vesna; Schmid, Doris; Marko, Florian; Velimirovic, Milica; Wagner, Stephan; von der Kammer, Frank; Hofmann, Thilo

2015-04-01

Successful emplacement of nanoscale zero-valent iron (nZVI) within the contaminated source zone is a prerequisite for the use of nZVI technology in groundwater remediation. Emplacement of nZVI is influenced i.e., by the injection technique and the injection velocity applied, as well as by the mobility of nZVI in the subsurface. Whereas processes linked to the injection can be controlled by the remediation practitioners, the mobility of nZVI in the subsurface remains limited. Even though mobility of nZVI is somewhat improved by surface coating with polyelectrolytes, it is still greatly affected by the groundwater composition and physical and chemical heterogeneities of aquifer grains. In order to promote mobility of nZVI it is needed to alter the surface charge heterogeneities of aquifer grains. Modifying the aquifer grain's surfaces by means of polyelectrolyte coating is an approach proposed to increase the overall negative surface charge of the aquifer grain surfaces, hinder deposition of nZVI onto aquifer grains, and finally promote nZVI mobility. In this study the effect of different polyelectrolytes on the nZVI mobility is tested in natural sands deriving from real brownfield sites that are proposed to be remediated using the nZVI technology. Sands collected from brownfield sites were characterized in terms of grain size distribution, mineralogical and chemical composition, and organic carbon content. Furthermore, surface charge of these sands was determined in both, low- and high ionic strength background solutions. Finally, changes of the sand's surface charges were examined after addition of the proposed aquifer modifiers, lignin sulfonate and humic acid. Surface charge of brownfield sands in low ionic strength background solution is more negative compared to that in high ionic strength background solution. An increase in negative surface potential of brownfield sand was recorded when aquifer modifiers were applied in a background solution with low ionic strength, indicating their potential to improve nZVI mobility under comparable environmental conditions. In contrast, no significant change of the surface potential of brownfield sand was observed when aquifer modifiers were applied in a background solution with high ionic strength. The potential of the aquifer modifiers to promote the mobility of nZVI was furthermore tested in flow-through columns, starting with the one filled with natural quartz sand with rough surface, low ionic strength background solutions and pre-injecting lignin sulfonate in concentration of 50 mg/L. The preliminary results showed that the pre-injection of lignin sulfonate does increase mobility of nZVI under this experimental condition. Further mobility tests will be carried out in order to elucidate the potential of the aquifer modifiers to promote the mobility of nZVI in sands with a complex mineralogy and in the background solutions with varying ionic strength, in order to account for the condition that resemble those at polluted sites. This research receives funding from the European Union's Seventh Framework Programme FP7/2007-2013 under grant agreement n°309517.

Mechanochemical pre-treatment for viable recycling of plastic waste containing haloorganics.

PubMed

Cagnetta, Giovanni; Zhang, Kunlun; Zhang, Qiwu; Huang, Jun; Yu, Gang

2018-05-01

Chemical recycling technologies are the most promising for a waste-to-energy/material recovery of plastic waste. However, 30% of such waste cannot be treated in this way due to the presence of halogenated organic compounds, which are often utilized as flame retardants. In fact, high quantities of hydrogen halides and dioxin would form. In order to enabling such huge amount of plastic waste as viable feedstock for recycling, an investigation on mechanochemical pre-treatment by high energy ball milling is carried out on polypropylene containing decabromodiphenyl ether. Results demonstrate that co-milling with zero valent iron and quartz sand ensures complete debromination and mineralization of the flame retardant. Furthermore, a comparative experiment demonstrates that the mechanochemical debromination kinetics is roughly proportional to the polymer-to-haloorganics mass ratio. Copyright © 2018 Elsevier Ltd. All rights reserved.

Quantitative Phase Analysis of Plasma-Treated High-Silica Materials

NASA Astrophysics Data System (ADS)

Kosmachev, P. V.; Abzaev, Yu. A.; Vlasov, V. A.

2018-06-01

The paper presents the X-ray diffraction (XRD) analysis of the crystal structure of SiO2 in two modifications, namely quartzite and quartz sand before and after plasma treatment. Plasma treatment enables the raw material to melt and evaporate after which the material quenches and condenses to form nanoparticles. The Rietveld refinement method is used to identify the lattice parameters of SiO2 phases. It is found that after plasma treatment SiO2 oxides are in the amorphous state, which are modeled within the microcanonical ensemble. Experiments show that amorphous phases are stable, and model X-ray reflection intensities approximate the experimental XRD patterns with fine precision. Within the modeling, full information is obtained for SiO2 crystalline and amorphous phases, which includes atom arrangement, structural parameters, atomic population of silicon and oxygen atoms in lattice sites.

36Cl: A tracer in groundwater in the aquia formation of Southern Maryland

USGS Publications Warehouse

Purdy, C.B.; Mignerey, A.C.; Helz, G.R.; Drummond, D.D.; Kubik, P.W.; Elmore, D.; Hemmick, T.

1987-01-01

The Aquia Formation (Paleocene) of Southern Maryland, a marine unit consisting predominantly of quartz sands, but containing 20-40% glauconite, represents one of the many productive, heavily pumped aquifers of the Southeastern Coastal Plain. An unusually high 36Cl activity ( ~ 15 ?? modem water) measured in an outcrop sample is interpreted as a result of the bomb pulse input. About 25 km downdip from the recharge area, a minimum in total chloride concentration occurs. This minimum is thought to correlate with the latest low-stand of sea-level, and thus to provide time information which is in general agreement with ages calculated from hydrodynamic data. However, significant increases in the 36Cl concentrations are observed along the flow path which may be due to ion filtration or to leakage of modem, bomb-contaminated water into the Aquia aquifer. ?? 1987.

Bacteriophage PRD1 batch experiments to study attachment, detachment and inactivation processes

NASA Astrophysics Data System (ADS)

Sadeghi, Gholamreza; Schijven, Jack F.; Behrends, Thilo; Hassanizadeh, S. Majid; van Genuchten, Martinus Th.

2013-09-01

Knowledge of virus removal in subsurface environments is pivotal for assessing the risk of viral contamination of water resources and developing appropriate protection measures. Columns packed with sand are frequently used to quantify attachment, detachment and inactivation rates of viruses. Since column transport experiments are very laborious, a common alternative is to perform batch experiments where usually one or two measurements are done assuming equilibrium is reached. It is also possible to perform kinetic batch experiments. In that case, however, it is necessary to monitor changes in the concentration with time. This means that kinetic batch experiments will be almost as laborious as column experiments. Moreover, attachment and detachment rate coefficients derived from batch experiments may differ from those determined using column experiments. The aim of this study was to determine the utility of kinetic batch experiments and investigate the effects of different designs of the batch experiments on estimated attachment, detachment and inactivation rate coefficients. The experiments involved various combinations of container size, sand-water ratio, and mixing method (i.e., rolling or tumbling by pivoting the tubes around their horizontal or vertical axes, respectively). Batch experiments were conducted with clean quartz sand, water at pH 7 and ionic strength of 20 mM, and using the bacteriophage PRD1 as a model virus. Values of attachment, detachment and inactivation rate coefficients were found by fitting an analytical solution of the kinetic model equations to the data. Attachment rate coefficients were found to be systematically higher under tumbling than under rolling conditions because of better mixing and more efficient contact of phages with the surfaces of the sand grains. In both mixing methods, more sand in the container yielded higher attachment rate coefficients. A linear increase in the detachment rate coefficient was observed with increased solid-water ratio using tumbling method. Given the differences in the attachment rate coefficients, and assuming the same sticking efficiencies since chemical conditions of the batch and column experiments were the same, our results show that collision efficiencies of batch experiments are not the same as those of column experiments. Upscaling of the attachment rate from batch to column experiments hence requires proper understanding of the mixing conditions. Because batch experiments, in which the kinetics are monitored, are as laborious as column experiments, there seems to be no major advantage in performing batch instead of column experiments.

Sedimentary controls on modern sand grain coat formation

NASA Astrophysics Data System (ADS)

Dowey, Patrick J.; Worden, Richard H.; Utley, James; Hodgson, David M.

2017-05-01

Coated sand grains can influence reservoir quality evolution during sandstone diagenesis. Porosity can be reduced and fluid flow restricted where grain coats encroach into pore space. Conversely pore-lining grain coats can restrict the growth of pore-filling quartz cement in deeply buried sandstones, and thus can result in unusually high porosity in deeply buried sandstones. Being able to predict the distribution of coated sand grains within petroleum reservoirs is thus important to help find good reservoir quality. Here we report a modern analogue study of 12 sediment cores from the Anllóns Estuary, Galicia, NW Spain, collected from a range of sub-environments, to help develop an understanding of the occurrence and distribution of coated grains. The cores were described for grain size, bioturbation and sedimentary structures, and then sub-sampled for electron and light microscopy, laser granulometry, and X-ray diffraction analysis. The Anllóns Estuary is sand-dominated with intertidal sand flats and saltmarsh environments at the margins; there is a shallowing/fining-upwards trend in the estuary-fill succession. Grain coats are present in nearly every sample analysed; they are between 1 μm and 100 μm thick and typically lack internal organisation. The extent of grain coat coverage can exceed 25% in some samples with coverage highest in the top 20 cm of cores. Samples from muddy intertidal flat and the muddy saltmarsh environments, close to the margins of the estuary, have the highest coat coverage (mean coat coverage of 20.2% and 21.3%, respectively). The lowest mean coat coverage occurs in the sandy saltmarsh (10.4%), beyond the upper tidal limit and sandy intertidal flat environments (8.4%), close to the main estuary channel. Mean coat coverage correlates with the concentration of clay fraction. The primary controls on the distribution of fine-grained sediment, and therefore grain coat distribution, are primary sediment transport and deposition processes that concentrate the clay fraction in the sediment towards the margins of the estuary. Bioturbation and clay illuviation/mechanical infiltration are secondary processes that may redistribute fine-grained sediment and produce grain coats. Here we have shown that detrital grain coats are more likely in marginal environments of ancient estuary-fills, which are typically found in the fining-upward part of progradational successions.

Density-lag anomaly patterns in backshore sands along a paraglacial barrier spit

NASA Astrophysics Data System (ADS)

Pupienis, Donatas; Buynevich, Ilya; Jarmalavičius, Darius; Fedorovič, Julija; Žilinskas, Gintautas; Ryabchuk, Daria; Kovaleva, Olga; Sergeev, Alexander; Cichon-Pupienis, Anna

2016-04-01

The Curonian Spit, located along the southeast Baltic Sea coast, is one of the longest paraglacial mega-barriers in the world (~100 km) and is characteried by microtidal sandy beaches and unbroken foredune ridge emplaced by human activities in historical times. Both are dominated by quartzo-feldpathic sand, with various fractions of heavy minerals that may be concentrated as density lag. Such heavy-mineral concentrations (HMCs) may be distributed weither randomly or regularly along the coast, depending on the geological framework, hydro-aeolian processes, and human activities (e.g., steel elements of coastal engineering structures, military installations, etc.). In this study, we focus on the longshore patterns in HMC distribution and relative magnitude (mainly the concentration of ferrimagnetic components). Along the entire Curonian Spit coast (Russia-Lithuania), a total of 184 surface sand samples were collected at 1 km interval from the berm and foredune toe (seaward base). HMCs were characterized in the laboratory using bulk low-field magnetic susceptibility (MS). The Wavelength and Lomb spectral analysis were used to assess the spatial rhythmicity of their longshore distribution. Generally, quartz sand is characterised by low MS values of ĸ<50 μSI, whereas higher values ĸ>150 μSI are typical for heavy mineral-rich sand. MS values on the berm and foredune toe range from 11.2-4977.9 μSI and from 9.2-3153.0 μSI, respectively. Density lag anomalies had MS values exceeding an average value by ≥3 times. Wavelength and Lomb spectral analysis allowed to identify several clusters of periodicities with wavelength varying from 2-12 km, with power spectra having statistically significant values (>95 % CI). Along the modern Curonian Spit coast, two scales of rhythmic pattern variation are evident: macroscale (≤12 km) and mesoscale (2-3 km). The former can be attributed to localized expressions of geological framework (iron-rich components) and engineering structures (especially within the southern part of the spit), whereas the mesoscale patterns reflect spatial distribution of short-term hydro-aeolian forcing (erosional-accretionary cells) that may shift temporally. This research was supported by Lithuanian Science Council (Grant No. MIP-039/2014), the Internationalization Program Award, Temple University and Russian Scientific Fund (Grant No. 14-37-00047).

Process for preparing fluorine-18

DOEpatents

Winchell, Harry S.; Wells, Dale K.; Lamb, James F.; Beaudry, Samuel B.

1976-09-21

An improved process for preparation of fluorine-18 by a neon (deuteron, alpha particle) fluorine-18 nuclear reaction in a non-reactive enclosed reaction zone wherein a ultrapure product is recovered by heating the reaction zone to a high temperature and removing the product with an inert gas.

Growth and Identification of Bacteria in N-Halamine Dental Unit Waterline Tubing Using an Ultrapure Water Source

PubMed Central

Porteous, Nuala; Luo, Jie; Hererra, Monica; Schoolfield, John; Sun, Yuyu

2011-01-01

This study examined bacterial growth and type on biofilm-controlling dental unit waterline (DUWL) tubing (T) and control manufacturer's tubing (C) in a laboratory DUWL model using ultrapure source water that was cycled through the lines. Sections of tubing lines were detached and examined for biofilm growth using SEM imaging at six sampling periods. Bacteria from inside surfaces of T and C, source unit, and reservoir were cultured and enumerated. At six months, organisms were molecularly identified from the alignment matches obtained from the top three BLAST searches for the 16S region. There was a 1–3 log increase in organism growth in a clean, nonsterile reservoir within an hour. Biofilm was established on the inside surfaces of C within three weeks, but not on T. Proteobacteria, and Sphingomonas spp. were identified in the source reservoir and C line, and a variation of the genera was found in T line. PMID:22220171

Sol-Gel Glasses

NASA Technical Reports Server (NTRS)

Mukherjee, S. P.

1985-01-01

Multicomponent homogeneous, ultrapure noncrystalline gels/gel derived glasses are promising batch materials for the containerless glass melting experiments in microgravity. Hence, ultrapure, homogeneous gel precursors could be used to: (1) investigate the effect of the container induced nucleation on the glass forming ability of marginally glass forming compositions; and (2) investigate the influence of gravity on the phase separation and coarsening behavior of gel derived glasses in the liquid-liquid immiscibility zone of the nonsilicate systems having a high density phase. The structure and crystallization behavior of gels in the SiO2-GeO2 as a function of gel chemistry and thermal treatment were investigated. As are the chemical principles involved in the distribution of a second network former in silica gel matrix being investigated. The procedures for synthesizing noncrystalline gels/gel-monoliths in the SiO2-GeO2, GeO2-PbO systems were developed. Preliminary investigations on the levitation and thermal treatment of germania silicate gel-monoliths in the Pressure Facility Acoustic Levitator were done.

Standard on microbiological management of fluids for hemodialysis and related therapies by the Japanese Society for Dialysis Therapy 2008.

PubMed

Kawanishi, Hideki; Akiba, Takashi; Masakane, Ikuto; Tomo, Tadashi; Mineshima, Michio; Kawasaki, Tadayuki; Hirakata, Hideki; Akizawa, Tadao

2009-04-01

The Committee of Scientific Academy of the Japanese Society for Dialysis Therapy (JSDT) proposes a new standard on microbiological management of fluids for hemodialysis and related therapies. This standard is within the scope of the International Organization for Standardization (ISO), which is currently under revision. This standard is to be applied to the central dialysis fluid delivery systems (CDDS), which are widely used in Japan. In this standard, microbiological qualities for dialysis water and dialysis fluids are clearly defined by endotoxin level and bacterial count. The qualities of dialysis fluids were classified into three levels: standard, ultrapure, and online prepared substitution fluid. In addition, the therapeutic application of each dialysis fluid is clarified. Since high-performance dialyzers are frequently used in Japan, the standard recommends that ultrapure dialysis fluid be used for all dialysis modalities at all dialysis facilities. It also recommends that the dialysis equipment safety management committee at each facility should validate the microbiological qualities of online prepared substitution fluid.

Blueberries on Earth and Mars: Correlations Between Concretions in Navajo Sandstone and Terra Meridiani on Mars.

NASA Astrophysics Data System (ADS)

Mahaney, W. C.; Milner, M. W.; Netoff, D.; Dohm, J.; Kalm, V.; Krinsley, D.; Sodhi, R. N.; Anderson, R. C.; Boccia, S.; Malloch, D.; Kapran, B.; Havics, A.

2008-12-01

Concretionary Fe-Mn-rich nodular authigenic constituents of Jurassic Navajo sandstone (moki marbles) bear a certain relationship to similar concretionary forms ('blueberries') observed on Mars. Their origin on Earth is considered to invoke variable redox conditions with underground fluids penetrating porous quartz-rich sandstone leading to precipitation of hematite and goethite-rich material from solution, generally forming around a central nucleus of fine particles of quartz and orthoclase, recently verified by XRD and SEM-EDS analyses. At the outer rim/inner nucleus boundary, bulbous lobes of fine-grained quartz often invade and fracture the outer rim armored matrix. The bulbous forms are interpreted to result from fluid explusion from the inner concretionary mass, a response to pressure changes accompanying overburden loading. Moki marbles, harder than enclosing rock, often weather out of in situ sandstone outcrops that form a surface lag deposit of varnished marbles that locally resemble desert pavement. The marbles appear morphologically similar to 'blueberries' identified on the martian surface in Terra Meridiani through the MER-1 Opportunity rover. On Earth, redox fluids responsible for the genesis of marbles may have emanated from deep in the crust (often influenced by magmatic processes). These fluids, cooling to ambient temperatures, may have played a role in the genesis of the cemented outer rim of the concretions. The low frequency of fungi filaments in the marbles, contrasts with a high occurrence in Fe-encrusted sands of the Navajo formation [1], indicating that microbial content is of secondary importance in marble genesis relative to the fluctuating influx of ambient groundwater. Nevertheless, the presence of filaments in terrestrial concretions hints at the possibility of discovering fossil/extant life on Mars, and thus should be considered as prime targets for future reconnaissance missions to Mars. 1] Mahaney, W.C., et al. (2004), Icarus, 171, 39-53.

Percutaneous multiple electrode connector, design parameters and fabrication (biomedical)

NASA Technical Reports Server (NTRS)

Myers, L. A.

1977-01-01

A percutaneous multielectrode connector was designed which utilizes an ultrapure carbon collar to provide an infection free biocompatible passage through the skin. The device provides reliable electrical continuity, mates and demates readily with the implant, and is fabricated with processes and materials oriented to commercial production.

Degradation of progestagens by oxidation with potassium permanganate in wastewater effluents

PubMed Central

2013-01-01

Background This study investigated the oxidation of selected progestagenic steroid hormones by potassium permanganate at pH 6.0 and 8.0 in ultrapure water and wastewater effluents, using bench-scale assays. Second order rate constants for the reaction of potassium permanganate with progestagens (levonorgestrel, medroxyprogesterone, norethindrone and progesterone) was determined as a function of pH, presence of natural organic matter and temperature. This work also illustrates the advantages of using a novel analytical method, the laser diode thermal desorption (LDTD-APCI) interface coupled to tandem mass spectrometry apparatus, allowing for the quick determination of oxidation rate constants and increasing sample throughput. Results The second-order rate constants for progestagens with permanganate determined in bench-scale experiments ranged from 23 to 368 M-1 sec-1 in both wastewater and ultrapure waters with pH values of 6.0 and 8.0. Two pairs of progestagens exhibited similar reaction rate constants, i.e. progesterone and medroxyprogesterone (23 to 80 M-1 sec-1 in ultrapure water and 26 to 149 M-1 sec-1 in wastewaters, at pH 6.0 and 8.0) and levonorgestrel and norethindrone (179 to 224 M-1 sec-1 in ultrapure water and 180 to 368 M-1 sec-1 in wastewaters, at pH 6.0 and 8.0). The presence of dissolved natural organic matter and the pH conditions improved the oxidation rate constants for progestagens with potassium permanganate only at alkaline pH. Reaction rates measured in Milli-Q water could therefore be used to provide conservative estimates for the oxidation rates of the four selected progestagens in wastewaters when exposed to potassium permanganate. The progestagen removal efficiencies was lower for progesterone and medroxyprogesterone (48 to 87 %) than for levonorgestrel and norethindrone (78 to 97%) in Milli-Q and wastewaters at pH 6.0-8.2 using potassium permanganate dosages of 1 to 5 mg L-1 after contact times of 10 to 60 min. Conclusion This work presents the first results on the permanganate-promoted oxidation of progestagens, as a function of pH, temperature as well as NOM. Progestagen concentrations used to determine rate constants were analyzed using an ultrafast laser diode thermal desorption interface coupled to tandem mass spectrometry for the analysis of water sample for progestagens. PMID:23675917

Comparison of homeopathic globules prepared from high and ultra-high dilutions of various starting materials by ultraviolet light spectroscopy.

PubMed

Klein, Sabine D; Wolf, Ursula

2016-02-01

Homeopathic globules are commonly used in clinical practice, while research focuses on liquid potencies. Sequential dilution and succussion in their production process has been proposed to change the physico-chemical properties of the solvent(s). It has been reported that aqueous potencies of various starting materials showed significant differences in ultraviolet light transmission compared to controls and between different dilution levels. The aim of the present study was to repeat and expand these experiments to homeopathic globules. Globules were specially produced for this study by Spagyros AG (Gümligen, Switzerland) from 6 starting materials (Aconitum napellus, Atropa belladonna, phosphorus, sulfur, Apis mellifica, quartz) and for 6 dilution levels (6x, 12x, 30c, 200c, 200CF (centesimal discontinuous fluxion), 10,000CF). Native globules and globules impregnated with solvents were used as controls. Globules were dissolved in ultrapure water, and absorbance in the ultraviolet range was measured. The average absorbance from 200 to 340nm was calculated and corrected for differences between measurement days and instrumental drift. Statistically significant differences were found for A. napellus, sulfur, and A. mellifica when normalized average absorbance of the various dilution levels from the same starting material (including control and solvent control globules) was compared. Additionally, absorbance within dilution levels was compared among the various starting materials. Statistically significant differences were found among 30c, 200c and 200CF dilutions. This study has expanded previous findings from aqueous potencies to globules and may indicate that characteristics of aqueous high dilutions may be preserved and detectable in dissolved globules. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Analysis of nutrition-relevant trace elements in human blood and serum by means of total reflection X-ray fluorescence (TXRF) spectroscopy

NASA Astrophysics Data System (ADS)

Stosnach, Hagen; Mages, Margarete

2009-04-01

In clinical service laboratories, one of the most common analytical tasks with regard to inorganic traces is the determination of the nutrition-relevant elements Fe, Cu, Zn, and Se. Because of the high numbers of samples and the commercial character of these analyses, a time-consuming sample preparation must be avoided. In this presentation, the results of total reflection X-ray fluorescence measurements with a low-power system and different sample preparation procedures are compared with those derived from analysis with common methods like Atomic Absorption Spectroscopy (AAS) and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS). The results of these investigations indicate that the optimal total reflection X-ray fluorescence analysis of the nutrition-relevant elements Fe, Cu, Zn, and Se can be performed by preparing whole blood and serum samples after dilution with ultrapure water and transferring 10 μl of internally standardized sample to an unsiliconized quartz glass sample carrier with subsequent drying in a laboratory oven. Suitable measurement time was found to be 600 s. The enhanced sample preparation by means of microwave or open digestion, in parts combined with cold plasma ashing, led to an improvement of detection limits by a factor of 2 for serum samples while for whole blood samples an improvement was only observed for samples prepared by means of microwave digestion. As the matrix elements P, S, Cl, and for whole blood Fe have a major influence on the detection limits, most probably a further enhancement of analytical quality requires the removal of the organic matrix. However, for the routine analysis of the nutrition-relevant elements, the dilution preparation was found to be sufficient.

Imaging the Transport of Silver Nanoparticles Through Soil With Synchrotron X-ray Microtomography

NASA Astrophysics Data System (ADS)

Molnar, I. L.; Gerhard, J.; O'Carroll, D. M.; Willson, C. S.

2012-12-01

Synchrotron x-ray computed microtomography (SXCMT) offers the ability to examine the spatial distribution of contaminants within the pore space of a porous medium; examples include the distribution of nonaqueous phase liquids (NAPLs) and micro-sized colloids. Recently presented was a method, based upon the application of the Beer-Lambert law and K-edge imaging, for using SXCMT to accurately determine the distribution of silver nanoparticles in a porous medium (Molnar et al., AGU Fall Meeting, H53B-1418, 2011). By capturing a series of SXCMT images of a single sample evolving over time, this technique can study the changing distribution of nanoparticles throughout the pore-network and even within individual pores. While previous work on this method focused on accuracy, precision and its potential applications, this study will provide an in-depth analysis of the results of multiple silver nanoparticle transport experiments imaged using this new technique. SXCMT images were collected at various stages of silver nanoparticle injection into columns packed with well graded and poorly graded quartz sand, iron oxide sand and glass bead porous media. The collected images were used to explore the influences of grain type, size and shape on the transport of silver nanoparticles through soil. The results of this analysis illustrate how SXCMT can collect hitherto unobtainable data which can yield valuable insights into the factors affecting nanoparticle transport through soil.

Transport and recovery of bacteriophage PRD1 in a sand and gravel aquifer: Effect of sewage-derived organic matter

USGS Publications Warehouse

Pieper, A.P.; Ryan, J.N.; Harvey, R.W.; Amy, G.L.; Illangasekare, T.H.; Metge, D.W.

1997-01-01

To test the effects of sewage-derived organic matter on virus attachment, 32P-labeled bacteriophage PRD1, linear alkylbenzene sulfonates (LAS), and tracers were injected into sewage-contaminated (suboxic, elevated organic matter) and uncontaminated (oxic, low organic matter) zones of an iron oxide-coated quartz sand and gravel aquifer on Cape Cod, MA. In the uncontaminated zone, 83% of the PRD1 were attenuated over the first meter of transport by attachment to aquifer grains. In the contaminated zone, 42% of the PRD1 were attenuated over the first meter of transport. Sewage-derived organic matter contributed to the difference in PRD1 attenuation by blocking attachment sites in the contaminated zone. At greater distances down gradient (to a total transport distance of 3.6 m), a near-constant amount of PRD1 continued to break through, suggesting that aquifer grain heterogeneities allowed a small amount of reversible attachment. Injection of an LAS mixture (25 mg L-1), a common sewage constituent, remobilized 87% of the attached PRD1 in the contaminated zone, but only 2.2% in the uncontaminated zone. LAS adsorption promoted virus recovery in the contaminated zone by altering the PRD1-surface interactions; however, the amount of LAS adsorbed was not sufficient to promote release of the attached PRD1 in the uncontaminated zone.

Composition of Eocene Ice-Rafted Debris, Central Arctic Ocean

NASA Astrophysics Data System (ADS)

Ramstad, C.; St. John, K.

2007-12-01

IODP Expedition 302 drilled a 400-m sediment record which contains physical evidence of ice-rafting in the Eocene and Neogene in the Arctic (Backman et al., 2006; Moran et al., 2006, St. John, in press). An increase in the terrigenous sand abundance occurs above 246 mcd (~46 Ma), with a flux similar to that in the Neogene. Higher resolution sampling in an interval of good recovery from 246-236 mcd shows evidence of cyclic input of IRD and biogenic components that fits with Milankovitch forcing at the obliquity period (Sangiorgi et al., in press). The question remains - what areas of the Arctic were ice-covered at this early stage in the Cenozoic? To address this provenance issue the composition of the terrigenous sands (250 micron fraction) in cores 55-56X is being quantified. Grains in 75 samples are being point-counted and their compositions categorized. Quartz grains are the dominant component (greater than 10,000 grains per gram), with some being hematite-stained, and there are lesser amounts of mafic minerals. No carbonate grains are identified so far in this study. Possible sources areas for Eocene IRD are the Eastern European and Russian Arctic margins. Tracking compositional variations of the IRD over the interval of cyclic deposition, should indicate whether the cyclic IRD deposition was consistently derived from one source region or multiple regions during this time.

DLVO, hydrophobic, capillary and hydrodynamic forces acting on bacteria at solid-air-water interfaces: Their relative impact on bacteria deposition mechanisms in unsaturated porous media.

PubMed

Bai, Hongjuan; Cochet, Nelly; Pauss, André; Lamy, Edvina

2017-02-01

Experimental and modeling studies were performed to investigate bacteria deposition behavior in unsaturated porous media. The coupled effect of different forces, acting on bacteria at solid-air-water interfaces and their relative importance on bacteria deposition mechanisms was explored by calculating Derjaguin-Landau-Verwey-Overbeek (DLVO) and non-DLVO interactions such as hydrophobic, capillary and hydrodynamic forces. Negatively charged non-motile bacteria and quartz sands were used in packed column experiments. The breakthrough curves and retention profiles of bacteria were simulated using the modified Mobile-IMmobile (MIM) model, to identify physico-chemical attachment or physical straining mechanisms involved in bacteria retention. These results indicated that both mechanisms might occur in both sand. However, the attachment was found to be a reversible process, because attachment coefficients were similar to those of detachment. DLVO calculations supported these results: the primary minimum did not exist, suggesting no permanent retention of bacteria to solid-water and air-water interfaces. Calculated hydrodynamic and resisting torques predicted that bacteria detachment in the secondary minimum might occur. The capillary potential energy was greater than DLVO, hydrophobic and hydrodynamic potential energies, suggesting that film straining by capillary forces might largely govern bacteria deposition under unsaturated conditions. Copyright © 2016 Elsevier B.V. All rights reserved.

Middle Pleistocene palaeoenvironmental changes of the eastern Canary Islands - revealed by the Mála dune-palaeosol-sequence at Lanzarote (Canary Islands)

NASA Astrophysics Data System (ADS)

von Suchodoletz, H.; Zöller, L.; Hilgers, A.; Radtke, U.; Faust, D.

2012-04-01

The Canary Islands are located at the transition between the Mediterranean and the Saharan climate off NW-Africa. Thus, they are a key area for the investigation of palaeoenvironmental changes. Several terrestrial studies investigated the palaeoenvironmental development of that region during the later part of the last glacial cycle. However, apart from recent investigations of "vega" sediments on Lanzarote Island (Suchodoletz et al. 2010) the palaeoenvironmental evolution during the Middle Pleistocene is hardly studied yet, basically due to the lack of reliable geochronological data. The Mála dune-palaeosol-sequence is located in the north of Lanzarote. It consists of marine shell detritus originally blown out from the insular shelf during periods of low global sea level, and to a small part of Saharan dust and fine quartz sand. The aeolian layers are intercalated with up to eight silty-clayey palaeosol horizons. Unlike the dune sands, the soils indicate stable landscape conditions with trapping of Saharan dust. Using a combination of ESR and luminescence dating techniques, we are able to place this sequence into the Middle Pleistocene, in contrast to former investigations based on 14C datings postulating a Late Pleistocene age (Ortiz et al. 2006). As a consequence, clayey-silty palaeosols represent periods of stable landscape conditions in the Canarian region during the Middle Pleistocene, which we compare with marine palaeoclimatic studies from the area.

Superhot fluids circulating close to magma intrusions: a contribution from analogue modelling

NASA Astrophysics Data System (ADS)

Montanari, Domenico; Agostini, Andrea; Bonini, Marco; Corti, Giacomo

2017-04-01

Magma overpressure at the time of the emplacement at shallow crustal levels may lead to deformation (i.e. forced folding, fracturing and faulting) in the country rock, both at local and regional scale. To get insights into this process, we reproduced and analysed in the laboratory the fracture/fault network associated with the emplacement of magma at shallow crustal levels. We used a mixture of quartz sand and K-feldspar fine sand as an analogue for the brittle crust, and polyglycerols for the magma. The models were able to reproduce complex 3D architectures of deformation resulting from magma emplacement, with different deformation patterns -invariably dominated by forced folding and associated brittle faulting/fracturing- resulting from variable parameters. These results provide useful hints into geothermal researches. Fractures and faults associated with magma emplacement are indeed expected to significantly influence the distribution and migration of superhot geothermal fluids near the edge of the magma intrusion. These structures can therefore be considered as potential targets for geothermal or mineral deposits exploration. In this perspective, the results of analogue models may provide useful geometric and conceptual constraints for field work, numerical modeling, and particularly seismic interpretation for achieving a better understanding and tuning of the integrated conceptual model concerning the circulation of supercritical fluids. The research leading to these results has received funding from the European Community's Seventh Framework Programme under grant agreement No. 608553 (Project IMAGE).

Noninvasive quantitative measurement of colloid transport in mesoscale porous media using time lapse fluorescence imaging.

PubMed

Bridge, Jonathan W; Banwart, Steven A; Heathwaite, A Louise

2006-10-01

We demonstrate noninvasive quantitative imaging of colloid and solute transport at millimeter to decimeter (meso-) scale. Ultraviolet (UV) excited fluorescent solute and colloid tracers were independently measured simultaneously during co-advection through saturated quartz sand. Pulse-input experiments were conducted at constant flow rates and ionic strengths 10(-3), 10(-2) and 10(-1) M NaCl. Tracers were 1.9 microm carboxylate latex microspheres and disodium fluorescein. Spatial moments analysis was used to quantify relative changes in mass distribution of the colloid and solute tracers over time. The solute advected through the sand at a constant velocity proportional to flow rate and was described well by a conservative transport model (CXTFIT). In unfavorable deposition conditions increasing ionic strength produced significant reduction in colloid center of mass transport velocity over time. Velocity trends correlated with the increasing fraction of colloid mass retained along the flowpath. Attachment efficiencies (defined by colloid filtration theory) calculated from nondestructive retained mass data were 0.013 +/- 0.03, 0.09 +/- 0.02, and 0.22 +/- 0.05 at 10(-3), 10(-2), and 10(-1) M ionic strength, respectively, which compared well with previously published data from breakthrough curves and destructive sampling. Mesoscale imaging of colloid mass dynamics can quantify key deposition and transport parameters based on noninvasive, nondestructive, spatially high-resolution data.

SINTERING OF NASCENT CALCIUM OXIDE

EPA Science Inventory

The paper discusses the measurement of the sintering rate of CaO in a nitrogen atmosphere at temperatures of 700-1100 C. CaO prepared from ultrapure CaCO3 was compared with an impure CaO derived from limestone. Both materials yielded an initial surface area of 104 sq m/g. The rat...

Intensity of quartz cathodoluminescence and trace-element content in quartz from the porphyry copper deposit at Butte, Montana

USGS Publications Warehouse

Rusk, B.G.; Reed, M.H.; Dilles, J.H.; Kent, A.J.R.

2006-01-01

Textures of hydrothermal quartz revealed by cathodoluminescence using a scanning electron microscope (SEM-CL) reflect the physical and chemical environment of quartz formation. Variations in intensity of SEM-CL can be used to distinguish among quartz from superimposed mineralization events in a single vein. In this study, we present a technique to quantify the cathodoluminescent intensity of quartz within individual and among multiple samples to relate luminescence intensity to specific mineralizing events. This technique has been applied to plutonic quartz and three generations of hydrothermal veins at the porphyry copper deposit in Butte, Montana. Analyzed veins include early quartz-molybdenite veins with potassic alteration, pyrite-quartz veins with sericitic alteration, and Main Stage veins with intense sericitic alteration. CL intensity of quartz is diagnostic of each mineralizing event and can be used to fingerprint quartz and its fluid inclusions, isotopes, trace elements, etc., from specific mineralizing episodes. Furthermore, CL intensity increases proportional to temperature of quartz formation, such that plutonic quartz from the Butte quartz monzonite (BQM) that crystallized at temperatures near 750 ??C luminesces with the highest intensity, whereas quartz that precipitated at ???250 ??C in Main Stage veins luminesces with the least intensity. Trace-element analyses via electron microprobe and laser ablation-ICP-MS indicate that plutonic quartz and each generation of hydrothermal quartz from Butte is dominated by characteristic trace amounts of Al, P, Ti, and Fe. Thus, in addition to CL intensity, each generation of quartz can be distinguished based on its unique trace-element content. Aluminum is generally the most abundant element in all generations of quartz, typically between 50 and 200 ppm, but low-temperature, Main Stage quartz containing 400 to 3600 ppm Al is enriched by an order of magnitude relative to all other quartz generations. Phosphorous is present in abundances between 25 and 75 ppm, and P concentrations in quartz show little variation among quartz generations. Iron is the least abundant of these elements in most quartz types and is slightly enriched in CL-dark quartz in pyrite-quartz veins with sericitic alteration. Titanium is directly correlated with both temperature of quartz precipitation, and intensity of quartz luminescence, such that BQM quartz contains hundreds of ppm Ti, whereas Main Stage quartz contains less than 10 ppm Ti. Our results suggest that Ti concentration in quartz is controlled by temperature of quartz precipitation and that increased Ti concentrations in quartz may be responsible for increased CL intensities.

Late Cenozoic Deformation in the Western Tarim Basin, NW China

NASA Astrophysics Data System (ADS)

Thompson, J. A.; Burbank, D. W.; Chen, J.; Li, T.

2009-12-01

The Tian Shan in NW China is one of the most active regions of intracontinental deformation in the world, accommodating a large fraction (~40%) of the shortening from the Indo-Eurasian collision. The western Tarim Basin, situated between the southern Tian Shan and Pamir Mountains, manifests this deformation through a series of east-west trending fault-related folds that have formed during the late Cenozoic. Previous studies in this region have focused on the kinematics, style, and timing of detachment folds related to folding within the foreland basin of the southern Tian Shan. In contrast, this study focuses on the deformation caused by fault-propagation folding resulting from the northward movement of the Pamir. The rates of deformation are calculated using a combination of optically stimulated luminescence (OSL) ages, structural mapping and differential GPS surveys of fault scarps and deformed terrace surfaces crossing active folds. OSL dating provides the time since the sediment was last exposed to daylight, i.e., time since burial. Consequently, OSL is useful for dating the abandonment of terrace surfaces due to tectonic (fold growth) or climatic events. OSL quartz samples were collected from silt lenses within gravel topping the terraces. Most of the quartz OSL signals are weak, thus several grain sizes (silt (4-11 µm, 8-15 µm) and sand (90-125 µm)) were analyzed and different integrations of the shine-down curves were explored to calculate equivalent doses. The implications for different equivalent doses and ages on the calculation of rates of deformation are also addressed.

Micromorphological difference between glacial and glaciofluvial quartz grain, evidence from Svalbard

NASA Astrophysics Data System (ADS)

Krbcová, Klára

2017-04-01

Micromorphology of glaciofluvial sediments were only partially shown by Mahaney et al. (2001). This paper deals with the main diagnostic textures of glaciofluvial sediments and changes of their micromorphology caused fluvial transport. All samples were collected in Svalbard in August 2012. Two glacial samples and six glaciofluvial samples were taken near the glacier Bertilbreen and one glacial sample and seven glaciofluvial samples were taken near the glacier Hørbyebreen. Samples were prepared according to the Mahaney (2002) and examined under electron microscope. The correlation analyses was used to set the main glaciofluvial microtextures. Similarity of the samples was tested by one-way ANOVA by F-test. Increasing numbers of V-shaped pits, rounded grains, meandering ridges and microblocks are typical for characteristic microtextures of glaciofluvial grains which had greater rate of fluvial transport. But the grains mainly transported by glacier had a greater percentage occurence of subangular grains, straight steps, straight and curved grooves, adhering particles, pitting and V-shaped etch pits. The fastest change in variability was set during the first kilometre of fluvial transport. The study was funded by the Grant Agency of Charles University (GAUK 1314214). Keywords: exoscopy, quartz grains micromorphology, glaciofluvial sediments References: MAHANEY, W. C. (2002): Atlas of sand grain surface textures and applications. Oxford University Press, USA, 237 s. MAHANEY, W. C., STEWART A., KALM, V. (2001): Quantification of SEM microtextures useful in sedimentary environmental discrimination. Boreas, 30, s. 165 - 171.

Mechanochemical destruction of mirex co-ground with iron and quartz in a planetary ball mill.

PubMed

Yu, Yunfei; Huang, Jun; Zhang, Wang; Zhang, Kunlun; Deng, Shubo; Yu, Gang

2013-02-01

Mechanochemical destruction (MCD) has been recognized as a promising non-combustion technology for the disposal of obsolete pesticides belonging to the persistent organic pollutants (POPs). Mirex, a termiticide ever used for many years in China, was ball milled in the presence of various reagent(s) in a planetary ball mill at room temperature to investigate the destruction efficiency. The ground samples were characterized and analyzed by Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, gas chromatography (GC), and ion chromatography (Martins, Bicego et al.). Under the same conditions of mill rotary rate and charge ratio, the mixture of iron powder and quartz sand (Fe/SiO(2)) was found best in promoting the mirex destruction. Mirex was completed destroyed after 2 h grinding at a charge ratio of 36:1 (reagent/mirex, m/m) and a mill rotation speed of 550 rpm. No organic compound was detected by GC/μECD screening. The yield of water-soluble chlorine determined by ion chromatography (Martins, Bicego et al.) in the final residue accounted for 90.7% of chlorine in the original mirex, which indicated a nearly complete dechlorination. Signals of both graphite and amorphous carbon were found in the Raman spectra of the co-ground powder samples. With the main final degradation products of water soluble Cl and carbon, the mechanism of the mechanochemical destruction approach should be dechlorination followed by the carbonization. Copyright © 2012 Elsevier Ltd. All rights reserved.

Analysis of the Importance of Oxides and Clays in Cd, Cr, Cu, Ni, Pb and Zn Adsorption and Retention with Regression Trees

PubMed Central

González-Costa, Juan José; Reigosa, Manuel Joaquín; Matías, José María; Fernández-Covelo, Emma

2017-01-01

This study determines the influence of the different soil components and of the cation-exchange capacity on the adsorption and retention of different heavy metals: cadmium, chromium, copper, nickel, lead and zinc. In order to do so, regression models were created through decision trees and the importance of soil components was assessed. Used variables were: humified organic matter, specific cation-exchange capacity, percentages of sand and silt, proportions of Mn, Fe and Al oxides and hematite, and the proportion of quartz, plagioclase and mica, and the proportions of the different clays: kaolinite, vermiculite, gibbsite and chlorite. The most important components in the obtained models were vermiculite and gibbsite, especially for the adsorption of cadmium and zinc, while clays were less relevant. Oxides are less important than clays, especially for the adsorption of chromium and lead and the retention of chromium, copper and lead. PMID:28072849

Clay deposits of the Tierra Colorado district, southern Orange County, California

USGS Publications Warehouse

Daviess, Steven Norman; Bramlette, M.N.

1953-01-01

The clay of this district is being mined for fire brick by the Vitrofrax Corporation. Much of the clay contains 35 percent or more of alumina and between 1 and 2 percent of iron oxide. Production is largely from an underground mine as the best clay deposit known in the district occurs on the side of a steep hill with more than 100 feet of sandstone overlying most of it. The good clay deposits occur at the base of an Eocene sandstone formation, and overlie mottled clays with a high iron content that are residual deposits formed on an old weathered surface. Mapping indicates that the clay deposits are very lenticular, though all occur at the same stratigraphic position, and they grade laterally into sandy clay and quartz sand. Topographic relief and the dip of the strata preclude finding large areas where the clay strata have relatively little overburden.

Environmental solid particle effects on compressor cascade performance

NASA Technical Reports Server (NTRS)

Tabakoff, W.; Balan, C.

1982-01-01

The effect of suspended solid particles on the performance of the compressor cascade was investigated experimentally in a specially built cascade tunnel, using quartz sand particles. The cascades were made of NACA 65(10)10 airfoils. Three cascades were tested, one accelerating cascade and two diffusing cascades. The theoretical analysis assumes inviscid and incompressible two dimensional flow. The momentum exchange between the fluid and the particle is accounted for by the interphase force terms in the fluid momentum equation. The modified fluid phase momentum equations and the continuity equation are reduced to the conventional stream function vorticity formulation. The method treats the fluid phase in the Eulerian system and the particle phase in Lagrangian system. The experimental results indicate a small increase in the blade surface static pressures, while the theoretical results indicate a small decrease. The theoretical analysis, also predicts the loss in total pressure associated with the particulate flow through the cascade.

Measuring air-water interfacial area for soils using the mass balance surfactant-tracer method.

PubMed

Araujo, Juliana B; Mainhagu, Jon; Brusseau, Mark L

2015-09-01

There are several methods for conducting interfacial partitioning tracer tests to measure air-water interfacial area in porous media. One such approach is the mass balance surfactant tracer method. An advantage of the mass-balance method compared to other tracer-based methods is that a single test can produce multiple interfacial area measurements over a wide range of water saturations. The mass-balance method has been used to date only for glass beads or treated quartz sand. The purpose of this research is to investigate the effectiveness and implementability of the mass-balance method for application to more complex porous media. The results indicate that interfacial areas measured with the mass-balance method are consistent with values obtained with the miscible-displacement method. This includes results for a soil, for which solid-phase adsorption was a significant component of total tracer retention. Copyright © 2015 Elsevier Ltd. All rights reserved.

Abrasion resistance of muscovite in aeolian and subaqueous transport experiments

NASA Astrophysics Data System (ADS)

Anderson, Calvin J.; Struble, Alexander; Whitmore, John H.

2017-02-01

Complementary aeolian and subaqueous transport experiments showed a trend in muscovite abrasion that may be useful for identifying ancient sandstones as aeolian or subaqueous in origin. We found that our experimental aeolian processes pulverized the micas quickly, while our subaqueous processes did not. In a pair of abrasion resistance experiments conducted with micaceous quartz sand, it was found that large muscovite grains were (1) reduced by aeolian processes to less than 500 μm in just 4 days, and (2) preserved by subaqueous processes to 610 ± 90 μm even after 356 days. At 20 days of aeolian transport no loose micas could be found even under the microscope, but after a year of subaqueous transport loose muscovite grains could still be seen with the naked eye. Thus, the occurrence and character of micas in a sandstone, particularly muscovite, may be helpful in determining the ancient depositional process.

An improved biofilter to control the dissolved organic nitrogen concentration during drinking water treatment.

PubMed

Zhang, Huining; Gu, Li; Liu, Bing; Gan, Huihui; Zhang, Kefeng; Jin, Huixia; Yu, Xin

2016-09-01

Dissolved organic nitrogen (DON) is a key precursor of numerous disinfection by-products (DBPs), especially nitrogenous DBPs (N-DBPs) formed during disinfection in drinking water treatment. To effectively control DBPs, reduction of the DON concentration before the disinfection process is critical. Traditional biofilters can increase the DON concentration in the effluent, so an improved biofilter is needed. In this study, an improved biofilter was set up with two-layer columns using activated carbon and quartz sand under different influent patterns. Compared with the single-layer filter, the two-layer biofilter controlled the DON concentration more efficiently. The two-point influent biofilter controlled the DON concentration more effectively than the single-point influent biofilter. The improved biofilter resulted in an environment (including matrix, DO, and pH) suitable for microbial growth. Along the depth of the biofilter column, the environment affected the microbial biomass and microbial activity and thus affected the DON concentration.

Wind ripples in low density atmospheres

NASA Technical Reports Server (NTRS)

Miller, J. S.; Marshall, J. R.; Greeley, R.

1987-01-01

The effect of varying fluid density (rho) on particle transport was examined by conducting tests at atmospheric pressures between 1 and 0.004 bar in the Martian Surface Wind Tunnel (MARSWIT). This study specifically concerns the effect of varying rho on the character of wind ripples, and elicits information concerning generalized ripple models as well as specific geological circumstances for ripple formation such as those prevailing on Mars. Tests were conducted primarily with 95 micron quartz sand, and for each atmospheric pressure chosen, tests were conducted at two freestream wind speeds: 1.1 U*(t) and 1.5 U*(t), where U*(t) is saltation threshold. Preliminary analysis of the data suggests: (1) ballistic ripple wavelength is not at variance with model predictions; (2) an atmospheric pressure of approximately 0.2 bar could represent a discontinuity in ripple behavior; and (4) ripple formation on Mars may not be readily predicted by extrapolation of terrestrial observations.

Exposure Assessment Suggests Exposure to Lung Cancer Carcinogens in a Painter Working in an Automobile Bumper Shop

PubMed Central

Kim, Boowook; Yoon, Jin-Ha; Choi, Byung-Soon; Shin, Yong Chul

2013-01-01

A 46-year-old man who had worked as a bumper spray painter in an automobile body shop for 15 years developed lung cancer. The patient was a nonsmoker with no family history of lung cancer. To determine whether the cancer was related to his work environment, we assessed the level of exposure to carcinogens during spray painting, sanding, and heat treatment. The results showed that spray painting with yellow paint increased the concentration of hexavalent chromium in the air to as much as 118.33 μg/m3. Analysis of the paint bulk materials showed that hexavalent chromium was mostly found in the form of lead chromate. Interestingly, strontium chromate was also detected, and the concentration of strontium chromate increased in line with the brightness of the yellow color. Some paints contained about 1% crystalline silica in the form of quartz. PMID:24422178

The Geomorphic System and the Effects of Human Interference at Gold Coast Beach in Tainan, Taiwan

NASA Astrophysics Data System (ADS)

Lin, Tsung-Yi

2017-04-01

The Gold Coast beach in Tainan, Taiwan, located between Anping harbor and Ur-Jen river mouth, is the subject of this study, which characterizes the beach's geomorphic system through the analysis of information such as sediment grain size, mineral composition, and periodic measurements of morphological changes of the beach. Based upon such characterizations, further analysis is conducted on the effects that human activities of the last 15 years have upon the geomorphic changes within the Gold Coast beach. The study shows that the median grain size of the Gold Coast beach's sediment is medium sand. The mineral composition includes mainly slate fragments and quartz grains, with small amounts of feldspar, sandstone and shell fragments. Based on a comprehensive study of the longshore distribution of beach sediment size and mineral composition of southwestern coast of Taiwan, as well as, the long-term, monitored data of waves, tides, and currents in this region, we conclude that the main process responsible for the sand accumulation at Gold Coast beach is the prevailing longshore sand transport from south to north. The southern breakwater of Anping harbor plays a role in intercepting the longshore transport sand and helps form the beach. Since the Ur-Jen river flows through a mudstone region, the suspended sediment plume during the flood season does not provide much sediment source to the sandy beach. A monthly beach profile survey project conducted between the years 1999 to 2000 revealed that the beach elevation and width had experienced an obvious seasonal change. The beach widened during the winter, but narrowed in the summer due to typhoon wave erosion. When the subaerial beach was eroded, a submerged longshore bar that was oriented almost parallel to the shoreline had formed at a distance about 400-600 meter away. With this observation, we can conclude that beach morphology is also influenced by various seasonal wave actions that affect onshore and offshore sand transport. An astonishing morphologic change at Gold Coast was observed as a 1500-meter reach of sandy beach at the southern end, near the Ur-Jen river mouth, disappeared in just a few years after the year 2005. The beach was not recovered the way it used to be in the winter season. The main reason for this geomorphic change could be the construction of a series of detached breakwaters on the coastal reach that is at the south side of Ur-Jen river mouth. Salients formed behind the detached breakwaters, which could have interrupted the south-to-north longshore sand transport. The Gold Coast became a sand-starved beach recently in the past 10 years, despite efforts of the government to construct more groins in this erosion area. Keywords: beach system, beach sediment, beach morphology, geomorphic processes, geomorphic change

A long record of extreme wave events in coastal Lake Hamana, Japan

NASA Astrophysics Data System (ADS)

Boes, Evelien; Yokoyama, Yusuke; Schmidt, Sabine; Riedesel, Svenja; Fujiwara, Osamu; Nakamura, Atsunori; Garrett, Ed; Heyvaert, Vanessa; Brückner, Helmut; De Batist, Marc

2017-04-01

Coastal Lake Hamana is located near the convergent tectonic boundary of the Nankai-Suruga Trough, along which the Philippine Sea slab is subducted underneath the Eurasian Plate, giving rise to repeated tsunamigenic megathrust earthquakes (Mw ≥ 8). A good understanding of the earthquake- and tsunami-triggering mechanisms is crucial in order to better estimate the complexity of seismic risks. Thanks to its accommodation space, Lake Hamana may represent a good archive for past events, such as tsunamis and tropical storms (typhoons), also referred to as "extreme wave" events. Characteristic event layers, consisting of sediment entrained by these extreme waves and their backwash, are witnesses of past marine incursions. By applying a broad range of surveying methods (reflection-seismic profiling, gravity coring, piston coring), sedimentological analyses (CT-scanning, XRF-scanning, multi-sensor core logging, grain size, microfossils etc.) and dating techniques (210Pb/137Cs, 14C, OSL, tephrochronology), we attempt to trace extreme wave event deposits in a multiproxy approach. Seismic imagery shows a vertical stacking of stronger reflectors, interpreted to be coarser-grained sheets deposited by highly energetic waves. Systematic sampling of lake bottom sediments along a transect from ocean-proximal to ocean-distal sites enables us to evaluate vertical and lateral changes in stratigraphy. Ocean-proximal, we observe a sequence of eight sandy units separated by silty background sediments, up to a depth of 8 m into the lake bottom. These sand layers quickly thin out and become finer-grained land-inward. Seismic-to-core correlations show a good fit between the occurrence of strong reflectors and sandy deposits, hence confirming presumptions based on acoustic imagery alone. Sand-rich intervals typically display a higher magnetic susceptibility, density and stronger X-ray attenuation. However, based on textural and structural differences, we can make the distinction between different types of sand units: i) massive to layered sands with a sharp, erosive lower contact, ii) thin, discontinuous sand lenses with a sharp lower contact and iii) inter-fingered sand-rich and silt-rich intervals with a gradual lower contact. Variability in appearance suggests a variety in triggering events too, going from tsunamis, over storm surges (typhoons) to the impact of sea-level changes on the interaction between tidal delta and lacustrine sedimentation. Preliminary dating (210Pb/137Cs) results in sedimentation rates of 0.4 cm/yr for the last 100-150 yr. Two closely-spaced tephra layers are tentatively linked with the reported Osawa Fuji scoria (3090 BP) and Kawago-daira pumice (3150 BP). However, more absolute ages (14C and OSL) are essential in order to obtain an accurate age-depth model and to position events in time. We are proceeding with the age determination of event sand beds based on single-grain OSL dating of feldspars. Whereas quartz appeared to be not suitable for dating, research in onshore archives close to Lake Hamana already proved the suitability of the IRSL50 signal of feldspar.

The Importance of Actualistic Source-to-Sink Sand Provenance Studies in Illuminating the Nature of Ancient Fluvial Systems From the Deep-Marine Clastic Successions They Sourced

NASA Astrophysics Data System (ADS)

Marsaglia, K. M.; Parra, J. G.; Dawson, S.

2006-12-01

Successions of gravity-flow deposits in deep-marine fan systems have the potential to record the evolution of their fluvial source region as well as specific tectonic, climatic, eustatic and anthropogenic events. Deciphering these signals involves the description and quantification of key sediment attributes such as fan volume, the rate of sediment accumulation, the frequency of depositional events, sediment texture, and sediment composition. Sediment composition/provenance provides insight into the nature of the fluvial source, including drainage basin geology and drainage development. For example, Marsaglia et al. (1995) demonstrated a connection between source river lengthening owing to eustatic change and sand composition in Quaternary turbidite successions of the Santa Barbara Basin at Ocean Drilling Program (ODP) Site 893. In contrast, longer-term compositional trends recognized in the Mesozoic to Cenozoic rift-to-drift successions cored by various ODP legs on the North Atlantic margins are more likely associated with continental margin drainage development and fluvial system evolution (Marsaglia et al., in press). These two connections between sink and source were made possible by well-documented petrologic data sets for both modern onshore fluvial systems and older offshore deep-marine successions, but in each case different workers collected the onshore and offshore data sets. In the Waipaoa River Sedimentary System of North Island, New Zealand we have taken a different, more holistic approach, with a limited and linked group of researchers and sample data base covering the complete system. The study area is an active forearc margin characterized by uplifted and deformed sedimentary successions and periodic input of arc-derived ash. Recently, the modern onshore system has been thoroughly documented via studies of the petrology of outcropping Mesozoic to Cenozoic units, fluvial terrace deposits, and modern fluvial sediments (e.g., James et al., in press). Now we are building on that data set and moving from source-to-sink to trace sandy sediment through the system out onto the shelf and slope where it has been encountered in shallow cores. Lessons learned onshore, such as a distinct compositional dependence on grain size and the relationships of bedrock geology to certain sand grain types, also apply to these offshore core samples. Many of the sandy intervals are largely composed of reworked tephra from Taupo eruptions, whereas quartz and feldspar dominate finer sand samples. Lithic-dominated sands are less common and coarser grained. Isolated greywacke gravel clasts indicate that at some point coarse sediment "leaked" into the basin from the south. The volumetric importance of this extrabasinal input can be assessed by looking at the types and proportions of lithic fragments within the finer sand fraction.

Removal of bromide and bromate from drinking water using granular activated carbon.

PubMed

Zhang, Yong-Qing; Wu, Qing-Ping; Zhang, Ju-Mei; Yang, Xiu-Hua

2015-03-01

Granular activated carbon (GAC) was used to remove bromide (Br⁻) and bromate (BrO(3)(-)) from drinking water in both bench- and pilot-scale experiments. The present study aims to minimize BrO(3)(-) formation and eliminate BrO(3)(-) generated during the ozonation of drinking water, particularly in packaged drinking water. Results show that the Br⁻ and BrO(3)(-) levels in GAC-treated water decreased in both bench- and pilot-scale experiments. In the bench-scale experiments, when the empty bed contact time (EBCT) was 5 min, the highest reduction rates of Br(-) in the mineral and ultrapure water were found to be 74.9% and 91.2%, respectively, and those of BrO(3)(-) were 94.4% and 98.8%, respectively. The GAC capacity for Br⁻ and BrO(3)(-) removal increased with the increase in EBCT. Reduction efficiency was better in ultrapure water than in mineral water. In the pilot-scale experiments, the minimum reduction rates of Br⁻ and BrO(3)(-) were 38.5% and 73.2%, respectively.

Toward industrial scale synthesis of ultrapure singlet nanoparticles with controllable sizes in a continuous gas-phase process

NASA Astrophysics Data System (ADS)

Feng, Jicheng; Biskos, George; Schmidt-Ott, Andreas

2015-10-01

Continuous gas-phase synthesis of nanoparticles is associated with rapid agglomeration, which can be a limiting factor for numerous applications. In this report, we challenge this paradigm by providing experimental evidence to support that gas-phase methods can be used to produce ultrapure non-agglomerated “singlet” nanoparticles having tunable sizes at room temperature. By controlling the temperature in the particle growth zone to guarantee complete coalescence of colliding entities, the size of singlets in principle can be regulated from that of single atoms to any desired value. We assess our results in the context of a simple analytical model to explore the dependence of singlet size on the operating conditions. Agreement of the model with experimental measurements shows that these methods can be effectively used for producing singlets that can be processed further by many alternative approaches. Combined with the capabilities of up-scaling and unlimited mixing that spark ablation enables, this study provides an easy-to-use concept for producing the key building blocks for low-cost industrial-scale nanofabrication of advanced materials.

Rapid Percolation of Water through Soil Macropores Affects Reading and Calibration of Large Encapsulated TDR Sensors

NASA Astrophysics Data System (ADS)

Matula, Svatopluk; Dolezal, Frantisek; Moreira Barradas, Joao Manuel

2015-04-01

The electromagnetic soil water content sensors are invaluable tools because of their selective sensitivity to water, versatility, ease of automation and large resolution. A common drawback of most their types is their preferential sensitivity to water near to their surfaces. The ways in which the drawback manifests itself were explored for the case of large Time-Domain Reflectometry (TDR) sensors Aqua-Tel-TDR (Automata, Inc., now McCrometer CONNECT). Their field performance was investigated and compared with the results of field and laboratory calibration. The field soil was loamy Chernozem on a carbonate-rich loess substrate, while the laboratory calibration was done in fine quartz sand. In the field, the sensors were installed horizontally into pre-bored holes after being wrapped in slurry of native soil or fine earth. Large sensor-to-sensor variability of readings was observed. It was partially removed by field calibration. The occurrence of percolation events could be easily recognised, because they made the TDR readings suddenly rising and sometimes considerably exceeding the saturated water content. After the events, the TDR readings fell, usually equally suddenly, remaining afterwards at the levels somewhat higher than those before the event. These phenomena can be explained by the preferential flow of water in natural and artificial soil macropores around the sensors. It is hypothesised that the percolating water which enters the gaps and other voids around the sensors accumulates there for short time, being hindered by the sensors themselves. This water also has a enlarged opportunity to get absorbed by the adjacent soil matrix. The variance of TDR readings obtained during the field calibration does not differ significantly from the variance of the corresponding gravimetric sampling data. This suggests that the slope of the field calibration equation is close to unity, in contrast to the laboratory calibration in quartz sand. This difference in slopes can be explained by the presence or absence, respectively, of gaps around the sensors. A typical percolation event and dry period records are presented and analysed. Sensors of this type can be used for qualitative detection of preferential flow and perhaps also for its quantification. The readings outside the percolation events indicate that the sensor environment imitates the native soil reasonably well and that the field-calibrated sensors can provide us with quantitative information about the actual soil water content.

Influence of climate on deep-water clastic sedimentation: application of a modern model, Peru-Chile Trough, to an ancient system, Ouachita Trough

USGS Publications Warehouse

Edgar, N. Terence; Cecil, C. Blaine

2003-01-01

Traditionally, an abrupt and massive influx of siliciclastic sediments into an area of deposition has been attributed to tectonic uplift without consideration of the influence of climate or climatic change on rates of weathering, erosion, transportation, and deposition. With few exceptions, fluvial sediment transport is minimal in both extremely arid climates and in perhumid (everwet) climates. Maximum sediment transport occurs in climates characterized by strongly seasonal rainfall, where the effect of vegetation on erosion is minimal. The Peru–Chile trench and Andes Mountain system (P–CT/AMS) of the eastern Pacific Ocean clearly illustrates the effects of climate on rates of weathering, erosion, transport, and deep-sea sedimentation. Terrigenous sediment is virtually absent in the arid belt north of lat. 30° S in the P–CT, but in the belt of seasonal rainfall south of lat. 30° S terrigenous sediment is abundant. Spatial variations in the amount and seasonality of annual precipitation are now generally accepted as the cause for this difference. The spatial variation in sediment supply to the P–CT appears to be an excellent modern analogue for the temporal variation in sediment supply to certain ancient systems, such as the Ouachita Trough in the southern United States. By comparison, during the Ordovician through the early Mississippian, sediment was deposited at very slow rates as the Ouachita Trough moved northward through the southern hemisphere dry belt (lat. 10° S to lat. 30° S). The deposystem approached the tropical humid zone during the Mississippian, coincident with increased coarse clastic sedimentation. By the Middle Pennsylvanian (Atokan), the provenance area and the deposystem moved well into the tropical humid zone, and as much as 8,500 m of mineralogically mature (but texturally immature) quartz sand was introduced and deposited. This increase in clastic sediment deposition traditionally has been attributed solely to tectonic activity. However, we contend that the principal control on the introduction of abundant terrigenous sediment was the movement of the deposystem from an arid or semiarid climate into a seasonally wetter climatic regime. The physical and mineralogical maturity of the quartz sand is the result of tropical weathering in provenance areas.

Bacteriophage PRD1 batch experiments to study attachment, detachment and inactivation processes.

PubMed

Sadeghi, Gholamreza; Schijven, Jack F; Behrends, Thilo; Hassanizadeh, S Majid; van Genuchten, Martinus Th

2013-09-01

Knowledge of virus removal in subsurface environments is pivotal for assessing the risk of viral contamination of water resources and developing appropriate protection measures. Columns packed with sand are frequently used to quantify attachment, detachment and inactivation rates of viruses. Since column transport experiments are very laborious, a common alternative is to perform batch experiments where usually one or two measurements are done assuming equilibrium is reached. It is also possible to perform kinetic batch experiments. In that case, however, it is necessary to monitor changes in the concentration with time. This means that kinetic batch experiments will be almost as laborious as column experiments. Moreover, attachment and detachment rate coefficients derived from batch experiments may differ from those determined using column experiments. The aim of this study was to determine the utility of kinetic batch experiments and investigate the effects of different designs of the batch experiments on estimated attachment, detachment and inactivation rate coefficients. The experiments involved various combinations of container size, sand-water ratio, and mixing method (i.e., rolling or tumbling by pivoting the tubes around their horizontal or vertical axes, respectively). Batch experiments were conducted with clean quartz sand, water at pH 7 and ionic strength of 20 mM, and using the bacteriophage PRD1 as a model virus. Values of attachment, detachment and inactivation rate coefficients were found by fitting an analytical solution of the kinetic model equations to the data. Attachment rate coefficients were found to be systematically higher under tumbling than under rolling conditions because of better mixing and more efficient contact of phages with the surfaces of the sand grains. In both mixing methods, more sand in the container yielded higher attachment rate coefficients. A linear increase in the detachment rate coefficient was observed with increased solid-water ratio using tumbling method. Given the differences in the attachment rate coefficients, and assuming the same sticking efficiencies since chemical conditions of the batch and column experiments were the same, our results show that collision efficiencies of batch experiments are not the same as those of column experiments. Upscaling of the attachment rate from batch to column experiments hence requires proper understanding of the mixing conditions. Because batch experiments, in which the kinetics are monitored, are as laborious as column experiments, there seems to be no major advantage in performing batch instead of column experiments. Copyright © 2013 Elsevier B.V. All rights reserved.

Potential of the Thermal Infrared Wavelength Region to predict semi-arid Soil Surface Properties for Remote Sensing Monitoring

NASA Astrophysics Data System (ADS)

Eisele, Andreas; Chabrillat, Sabine; Lau, Ian; Hecker, Christoph; Hewson, Robert; Carter, Dan; Wheaton, Buddy; Ong, Cindy; Cudahy, Thomas John; Kaufmann, Hermann

2014-05-01

Digital soil mapping with the means of passive remote sensing basically relies on the soils' spectral characteristics and an appropriate atmospheric window, where electromagnetic radiation transmits without significant attenuation. Traditionally the atmospheric window in the solar-reflective wavelength region (visible, VIS: 0.4 - 0.7 μm; near infrared, NIR: 0.7 - 1.1 μm; shortwave infrared, SWIR: 1.1 - 2.5 μm) has been used to quantify soil surface properties. However, spectral characteristics of semi-arid soils, typically have a coarse quartz rich texture and iron coatings that can limit the prediction of soil surface properties. In this study we investigated the potential of the atmospheric window in the thermal wavelength region (long wave infrared, LWIR: 8 - 14 μm) to predict soil surface properties such as the grain size distribution (texture) and the organic carbon content (SOC) for coarse-textured soils from the Australian wheat belt region. This region suffers soil loss due to wind erosion processes and large scale monitoring techniques, such as remote sensing, is urgently required to observe the dynamic changes of such soil properties. The coarse textured sandy soils of the investigated area require methods, which can measure the special spectral response of the quartz dominated mineralogy with iron oxide enriched grain coatings. By comparison, the spectroscopy using the solar-reflective region has limitations to discriminate such arid soil mineralogy and associated coatings. Such monitoring is important for observing potential desertification trends associated with coarsening of topsoil texture and reduction in SOC. In this laboratory study we identified the relevant LWIR wavelengths to predict these soil surface properties. The results showed the ability of multivariate analyses methods (PLSR) to predict these soil properties from the soil's spectral signature, where the texture parameters (clay and sand content) could be predicted well in the models using the LWIR-window (sand content: R2 = 0.84 and RMSECV = 1.09 %, and for clay content: R2 = 0.77 and RMSECV = 1.0 %, both with 3 factor models). In comparison, the quantification from the solar-reflective window showed its limitations in its relative complex PLSR models and a lower prediction accuracy (sand content: R2 = 0.69 and RMSECV = 1.5 % with 7 factors, and for clay content: R2 = 0.64 and RMSECV = 1.26 % with 9 factors). The prediction of the SOC content, on the other hand, showed minor disparity between the two atmospheric windows (LWIR: R2 = 0.73 and RMSECV = 0.1 % with 6 factors, VNIR-SWIR: R2 = 0.69 and RMSECV = 0.11 %, with 9 factors). The prospect of the LWIR for determining soil texture was demonstrated to be even more impressive when reduced to the spectral band specifications of airborne (TASI-600) and spaceborne (ASTER) sensors. The results demonstrate the high potential of the LWIR to detect and quantify soil surface properties in the future for a monitoring via LWIR hyperspectral remote sensing.

Transport Behavior of Functionalized Multi-Wall Carbon Nanotubes in Water-Saturated Quartz Sand as a Function of Tube Length

PubMed Central

Wang, Yonggang; Kim, Jae-Hong; Baek, Jong-Beom; Miller, Gary W.; Pennell, Kurt D.

2012-01-01

A series of one-dimensional column experiments was conducted to examine the effects of tube length on the transport and deposition of 4-ethoxybenzoic acid functionalized multi-wall carbon nanotubes (MWCNTs) in water-saturated porous media. Aqueous MWCNTs suspensions were prepared to yield three distributions of tube lengths; 0.02–1.3 μm (short), 0.2–7.5 μm (medium), and 0.2–21.4 μm (long). Results of the column studies showed that MWCNT retention increased with increasing tube length. Nevertheless, more than 76% of the MWCNT mass delivered to the columns was detected in effluent samples under all experimental conditions, indicating that the functionalized MWCNTs were readily transported through 40–50 mesh Ottawa sand. Examination of MWCNT length distributions in the effluent samples revealed that nanotubes with lengths greater than 8 μm were preferentially deposited. In addition, measured retention profiles exhibited the greatest MWCNT deposition near the column inlet, which was most pronounced for the long MWCNTs, and decreased sharply with travel distance. Scanning electron microscope (SEM) images showed that MWCNTs were deposited on sand surfaces over the entire column length, while larger MWCNT bundles were retained at grain intersections and near the column inlet. A mathematical model based on clean bed filtration theory (CBFT) was unable to accurately simulate the measured retention profile data, even after varying the weighting function and incorporating a nonuniform attachment rate coefficient expression. Modification of the mathematical model to account for physical straining greatly improved predictions of MWCNT retention, yielding straining rate coefficients that were four orders-of-magnitude greater than corresponding attachment rate coefficients. Taken in concert, these experimental and modeling results demonstrate the potential importance of, and need to consider, particle straining and tube length distribution when describing MWCNT transport in water-saturated porous media. PMID:22704927

Transport behavior of functionalized multi-wall carbon nanotubes in water-saturated quartz sand as a function of tube length.

PubMed

Wang, Yonggang; Kim, Jae-Hong; Baek, Jong-Beom; Miller, Gary W; Pennell, Kurt D

2012-09-15

A series of one-dimensional column experiments was conducted to examine the effects of tube length on the transport and deposition of 4-ethoxybenzoic acid functionalized multi-wall carbon nanotubes (MWCNTs) in water-saturated porous media. Aqueous MWCNTs suspensions were prepared to yield three distributions of tube lengths; 0.02-1.3 μm (short), 0.2-7.5 μm (medium), and 0.2-21.4 μm (long). Results of the column studies showed that MWCNT retention increased with increasing tube length. Nevertheless, more than 76% of the MWCNT mass delivered to the columns was detected in effluent samples under all experimental conditions, indicating that the functionalized MWCNTs were readily transported through 40-50 mesh Ottawa sand. Examination of MWCNT length distributions in the effluent samples revealed that nanotubes with lengths greater than 8 μm were preferentially deposited. In addition, measured retention profiles exhibited the greatest MWCNT deposition near the column inlet, which was most pronounced for the long MWCNTs, and decreased sharply with travel distance. Scanning electron microscope (SEM) images showed that MWCNTs were deposited on sand surfaces over the entire column length, while larger MWCNT bundles were retained at grain intersections and near the column inlet. A mathematical model based on clean bed filtration theory (CBFT) was unable to accurately simulate the measured retention profile data, even after varying the weighting function and incorporating a nonuniform attachment rate coefficient expression. Modification of the mathematical model to account for physical straining greatly improved predictions of MWCNT retention, yielding straining rate coefficients that were four orders-of-magnitude greater than corresponding attachment rate coefficients. Taken in concert, these experimental and modeling results demonstrate the potential importance of, and need to consider, particle straining and tube length distribution when describing MWCNT transport in water-saturated porous media. Copyright © 2012 Elsevier Ltd. All rights reserved.

Sediment characteristics and provenance of the Taiwan Shoal in the southern Taiwan Strait

NASA Astrophysics Data System (ADS)

Koo, W. S.; Lin, A. T.; Kuo, L. W.; Lee, Y. H.

2016-12-01

The Taiwan Shoal in the southern Taiwan Strait exhibits a lobe-shaped shallow water area, with a depth less than around 40 m and an area approximately of 13,000 km2. The Shoal consists of relict sediments remnant from deltaic deposits during the last glacial period and associated with the paleo-Min River. We collected seafloor sediments in and around the Taiwan Shoal to study the sediment characteristics and provenance of the Shoal as well as Taiwanese river sediments to characterize sediment sourced from southern Taiwan. Our results help to understand possible sediment delivery pathways in a source-to-sink context from the southern Taiwan Strait to the northern South China Sea. The method of X-ray diffraction is used to identify mineral compositions for muds and mineral compositions are examined under polarized microscope for sands. Zircon grains are separated from heavy minerals for U-Pb dating in order to understand the sediment source terranes. Sediments of the Taiwan Shoal are mostly tawny-colored, medium to coarse-grained sands with abundant shell fragments and shallow-water benthic foraminifera. Sediments to the south of the Taiwan Shoal and in the outer shelf consist of dark brown-colored and fine-grained sands with rare shell fragments. Siliciclastic compositions of the Taiwan Shoal sediments are mostly quartz. The second abundant composition is rock fragments with more occurrences near the Chinese coastline and the Penghu archipelago. Slate fragments are found to occur near Taiwan, especially in the Penghu Channel area. Clay minerals from the Penghu Channels and south of the Taiwan Shoal are dominated by illite and chlorite with minor smectite and kaolinite. The sediment colors and mineral species are very different for the sediments of the Taiwan Shoal and outer shelf, revealing that these two areas featuring different oceanographic processes and sediment provenance.

Characterization and origin of spongillite-hosting sediment from João Pinheiro, Minas Gerais, Brazil

NASA Astrophysics Data System (ADS)

Almeida, A. C. S.; Varajão, A. F. D. C.; Gomes, N. S.; Varajão, C. A. C.; Volkmer-Ribeiro, C.

2010-03-01

Spongillite from João Pinheiro, Minas Gerais, Brazil is mainly known for its use in brick production and in the refractory industry. Very few studies have focused on its geological context. Spongillite-rich deposits occur in shallow ponds on a karstic planation surface developed on rocks of the Neoproterozoic São Francisco Supergroup. Cenozoic siliciclastic sediments are related to this surface. A field study of these deposits and analysis of multispectral images showed a SE-NW preferential drainage system at SE, suggesting that Mesozoic Areado Group sandstones were the source area of the spongillite-hosting sediments. Mineralogical and textural characterization by optical microscopic analysis, X-ray diffraction (XRD), differential and gravimetric thermal analysis (DTA-GTA), infrared spectroscopy (IR) and scanning electron microscopy (SEM) of seven open-pit spongillite-rich deposits (Avião, Carvoeiro, Vânio, Preguiça, Divisa, Severino, Feijão) showed a sedimentological similarity between the deposits. They are lens-shaped and are characterized at the bottom by sand facies, in the middle by spicules-rich muddy-sand facies and at the top by organic matter-rich muddy-sand facies. Petrographically, the spongillite-hosting sediments and the siliclastic sediments of the Areado Group show detrital phases with similar mineralogical and textural features, such as the presence of well-sorted quartz grains and surface features of abrasion typical of aeolian reworking that occurred in the depositional environment in which the sandstones of the Areado Group were formed. Detrital heavy minerals, such as staurolite, zircon, tourmaline, and clay minerals, such as kaolinite, low amounts of illite, scarce chlorite and mixed-layer chlorite/smectite and illite/smectite occur in the spongillite-hosting sediments and in sandstones from the Areado Group. In both formations, staurolite has similar chemical composition. These mineralogical and textural features show that the sediments of the Areado Group constitute the main source of the pond sediments that host spongillite.

Mohawk Lake or Mohawk meadow Sedimentary facies and stratigraphy of Quaternary deposits in Mohawk Valley, upper Middle Fork of the Feather River, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yount, J.C.; Harwood, D.S.; Bradbury, J.P.

1993-04-01

Mohawk Valley (MV) contain thick, well-exposed sections of Quaternary basin-fill sediments, with abundant interbedded tephra and a diverse assemblage of sedimentary facies. The eastern arm of MV, extending from Clio to Portola, contains as much as 100 m of trough cross-bedded cobble to pebble gravel and planar and trough cross-bedded coarse and medium sand, interpreted as braided stream deposits. Sections exposed in the western arm of MV consist in their lower parts of massive organic-rich silt and clay interbedded with blocky to fissile peat beds up to 1 m thick. Diatom assemblages are dominated by benthic species indicating fresh marshmore » environments with very shallow water depths of one meter or less. Proglacial lacustrine deposits of limited lateral extent are present within the outwash complexes as evidenced by varved fine sand and silt couplets, poorly sorted quartz-rich silt beds containing dropstones, and contorted beds of diamict grading laterally into slump blocks surrounded by wood-bearing silt and silty sand. The Rockland Ash (400 ka) is a prominent marker in the middle or lower part of many sections throughout MV, indicating that at least half of the basin-fill sequence is Late Quaternary in age. A log buried in diamict slumped into a proglacial lake lying approximately 3 km downstream from the Tioga Stage ice termini in Jamison and Gray Eagle Creeks yields an age of 18,715 [+-]235 C[sup 14] years BP. Previous interpretations of MV deposits originating in a large, deep lake with water depths in excess of 150 m are untenable given the sedimentary facies and diatom floras that dominate the valley. Unexhumed valleys such as Sierra Valley to the east and Long Valley to the northwest which contain large meadows traversed by braided streams are probably good analogs for the conditions that existed during the accumulation of the Mohawk Valley deposits.« less

Eolian depositional phases during the past 50 ka and inferred climate variability for the Pampean Sand Sea, western Pampas, Argentina

NASA Astrophysics Data System (ADS)

Tripaldi, Alfonsina; Forman, Steven L.

2016-05-01

The Pampean Sand Sea, which occurs from the Argentinian Pampas to the eastern Andean piedmont, hosts presently stabilized dune fields spanning the late Quaternary. This study integrates previous results and presents new geomorphic, stratigraphic, sedimentological, and chronologic data for nineteen >2 m-thick eolian successions for the San Luis paleo-dune field, western Pampas, to better constrain the depositional history. Six eolian depositional phases are identified spanning the past 50 ka, interposed with paleosols and/or bounded by erosive surfaces. Age control was from 61 OSL ages of small aliquots of quartz grains from eolian stratigraphic units. The inferred timing of eolian phases are at ca. 70 ± 10 yr, 190 ± 20 yr, 12 to 1 ka, 22 to 17 ka, 29 to 24 ka, and 40 to 32 ka. A maximum span for periods of pedogenesis at ca. 12 to 17 ka, 22 to 24 ka, and 29 to 32 ka was provided by bounding OSL ages, which broadly overlap with high stands of pluvial lakes and glacier advances in the central Andes. We infer that the added precipitation may reflect expansion of the Southern Hemisphere monsoon, associated with Northern Hemisphere Heinrich events, leading to episodes of significantly wetter conditions (>350 mm MAP) to at least 35° S. Most of the Holocene (12 ka to 0.8 ka) was characterized by sand sheet deposit under drier than present conditions (100-450 mm MAP), associated with Monte-type vegetation (shrub steppe). The latest two eolian depositional phases, occurred at ca. 190 and 70 yr ago, during the historic period with European settlement and are related to anthropogenic landscape disturbance, though the youngest phase was concomitant with 1930s drought. Wet conditions dominated since ca. AD 1970 with new lakes and rivers forming across this eolian terrain; an incongruous environmental response in reference to drier conditions for most of the Holocene.

26Al - 10Be cosmogenic nuclide isochron burial dating in combination with luminescence dating of two Danube terraces

NASA Astrophysics Data System (ADS)

Neuhuber, Stephanie; Braumann, Sandra; Lüthgens, Christopher; Fiebig, Markus; Häuselmann, Philipp; Schäfer, Jörg

2016-04-01

The Quaternary sediment record in the Vienna Basin is influenced by two main factors: (1) the tectonic development of a pull apart basin along a sinistral strike slip fault system between the Eastern Alps and the West Carpathians and by (2) strongly varying sediment supply during the Plio- and Pleistocene. From the Late Pannonian (8.8 Ma) onward a large-scale regional uplift (Decker et al., 2005) controls terrace formation in the Vienna Basin. The main sediment supply into the Vienna Basin originates from the Danube, and subordinately from tributaries to the south such as Piesting, Fischa, Leitha and from the north by the river March. Today the Danube forms a large floodplain that is bordered to the north by one large Pleistocene terrace, the Gänserndorf Terrace that is situated 17 m above todays water level. Farther to the east a smaller terrace, the Schlosshof Terrace, reaches 25 m above todays water level. These terrace levels are tilted by movement of underlying blocks (Peresson, 2006). Both, the Schlosshof and Gänserndorf terraces consist of successions of up to 2 m thick gravel beds with intercalated sand layers or -lenses that may locally reach thicknesses up to 0.8 m. At each terrace one gavel pit was selected to calculate the time of terrace deposition by luminescence dating in combination with 26Al/10Be cosmogenic nuclide isochrone dating (Balco and Rovery, 2008). Five quartz stones from the base of each terrace were physically and chemically processed to obtain Al and Be oxides for Acceleration Mass Spectrometry. Sand samples for luminescence dating were taken above the cosmogenic nuclide samples from the closest suitable sand body. Decker et al., 2005. QSR 24, 307-322 Peresson, 2006 Geologie der österreichischen Bundesländer Niederösterreich 255-258 Balco and Rovey, 2008. AJS 908, 1083-1114 Thanks to FWF P 23138-N19, OMAA 90öu17

Measurement of Polycyclic Aromatic Hydrocarbons in Airborne Particulate Matter at Low Concentrations

DTIC Science & Technology

2012-03-01

Soil & Water Colorimetric (diphenylcarbazide) 7199 Hexavalent Chromium by Ion Chromatography 218.6 Low level chelation & extraction NATTS...Hexane:Dichloromethane:Methanol Dionex ASE 200 Sample Concentration Evaporation in Ultrapure Nitrogen Stream Zymark Turbovap Solid Phase Extraction Supelco Custom...Glass Silica SPE Cartridge 1% Dichloromethane + 1% Acetone in Hexane GCMS Analysis Conventional Splitless Injection Selective Ion Monitoring

A mixed carbonate/clastic example in a restricted bay in a temperate carbonate shelf (Cala Fornells, northern Minorca Spain)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fornos, J.J.; Forteza, V.; Jaume, C.

1990-05-01

Cala Fornells is a restricted bay located in the northern section of the island Minorca. Cala Fornells has a surface area of 4 km{sup 2} and a maximum depth of 25 m at the mouth, which connects with the northern Minorca platform. Due to ephemeral streams with very fine textural inflow, the sedimentary facies present in the floor of the bay are primarily controlled by the bioclastic carbonate ecosystem production and the terrigenous input. The distribution of the facies is related to three major factors: (1) bathymetry, which controls the ecosystem distribution (Cymodocea nodosa-Caulerpa prolifera, Posidonia oceanica, and maeerl communities,more » from shallowest to deepest); (2) hydrodynamic conditions due to northern winds (locally called Tramuntana), which control the grain size distribution; and (3) local ephemeral streams, which control the terrigenous input. In the coarser fractions of the sediment (gravel and sand), the main component in the deepest zones are skeletal fragments of red algae. The shallowest zones contain fragments of the green alga Halimeda tuna, which may represent up to 50% of the total bioclastic fraction. The terrigenous components are mostly shales and only locally do they find a sand fragment of limestone and quartz grains. The organic matter content is very high (over 6% in the finest fractions), whereas in the more hydrodynamic and deeper facies (25 m) where the bioclastic fractions are predominant, the organic carbon content is below 0.5%.« less

Physical abrasion of mafic minerals and basalt grains: application to Martian aeolian deposits

USGS Publications Warehouse

Cornwall, Carin; Bandfield, Joshua L.; Titus, Timothy N.; Schreiber, B. C.; Montgomery, D.R.

2015-01-01

Sediment maturity, or the mineralogical and physical characterization of sediment deposits, has been used to locate sediment source, transport medium and distance, weathering processes, and paleoenvironments on Earth. Mature terrestrial sands are dominated by quartz, which is abundant in source lithologies on Earth and is physically and chemically stable under a wide range of conditions. Immature sands, such as those rich in feldspars or mafic minerals, are composed of grains that are easily physically weathered and highly susceptible to chemical weathering. On Mars, which is predominately mafic in composition, terrestrial standards of sediment maturity are not applicable. In addition, the martian climate today is cold, dry and sediments are likely to be heavily influenced by physical weathering rather than chemical weathering. Due to these large differences in weathering processes and composition, martian sediments require an alternate maturity index. Abrason tests have been conducted on a variety of mafic materials and results suggest that mature martian sediments may be composed of well sorted, well rounded, spherical basalt grains. In addition, any volcanic glass present is likely to persist in a mechanical weathering environment while chemically altered products are likely to be winnowed away. A modified sediment maturity index is proposed that can be used in future studies to constrain sediment source, paleoclimate, mechanisms for sediment production, and surface evolution. This maturity index may also provide details about erosional and sediment transport systems and preservation processes of layered deposits.

Drought drove forest decline and dune building in eastern upper Michigan, USA, as the upper Great Lakes became closed basins

USGS Publications Warehouse

Loope, Walter L.; Loope, Henry M.; Goble, Ronald J.; Fisher, Timothy G.; Lytle, David E.; Legg, Robert J.; Wysocki, Douglas A.; Hanson, Paul R.; Young, Aaron R.

2012-01-01

Current models of landscape response to Holocene climate change in midcontinent North America largely reconcile Earth orbital and atmospheric climate forcing with pollen-based forest histories on the east and eolian chronologies in Great Plains grasslands on the west. However, thousands of sand dunes spread across 12,000 km2 in eastern upper Michigan (EUM), more than 500 km east of the present forest-prairie ecotone, present a challenge to such models. We use 65 optically stimulated luminescence (OSL) ages on quartz sand deposited in silt caps (n = 8) and dunes (n = 57) to document eolian activity in EUM. Dune building was widespread ca. 10–8 ka, indicating a sharp, sustained decline in forest cover during that period. This decline was roughly coincident with hydrologic closure of the upper Great Lakes, but temporally inconsistent with most pollen-based models that imply canopy closure throughout the Holocene. Early Holocene forest openings are rarely recognized in pollen sums from EUM because faint signatures of non-arboreal pollen are largely obscured by abundant and highly mobile pine pollen. Early Holocene spikes in nonarboreal pollen are recorded in cores from small ponds, but suggest only a modest extent of forest openings. OSL dating of dune emplacement provides a direct, spatially explicit archive of greatly diminished forest cover during a very dry climate in eastern midcontinent North America ca. 10–8 ka.

A 7.2 keV spherical crystal backlighter system for Sandia's Z Pulsed Power Facility

NASA Astrophysics Data System (ADS)

Schollmeier, M.; Knapp, P. F.; Ampleford, D. J.; Loisel, G. P.; Robertson, G.; Shores, J. E.; Smith, I. C.; Speas, C. S.; Porter, J. L.; McBride, R. D.

2016-10-01

Many experiments on Sandia's Z facility, a 30 MA, 100 ns rise-time, pulsed-power driver, use a monochromatic Quartz crystal imaging backlighter system at 1.865 keV (Si Heα) or 6.151 keV (Mn Heα) x-ray energy to radiograph an imploding liner (cylindrical tube) or wire array. The x-ray source is generated by the Z-Beamlet Laser (ZBL), which provides up to 4.5 kJ at 527 nm during a 6 ns window. Radiographs of an imploding thick-walled Beryllium liner at a convergence ratio of about 20 [CR =Rin . (0) /Rin . (t) ] were too opaque to identify the inner surface of the liner with high confidence, demonstrating the need for a higher-energy x-ray backlighter between 6 and 10 keV. We present the design, test and first application of a Ge (335) spherical crystal x-ray backlighter system using the 7.242 keV Co Heα resonance line. The system operates at an almost identical Bragg angle as the existing 1.865 and 6.151 keV backlighters, enhancing our capabilities such as two-color, two-frame radiography, without changing detector shielding hardware. SAND No: SAND2016-6724 A. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corp., a wholly owned subsidiary of Lockheed Martin Corp., for the U.S. DoE NNSA under contract DE-AC04-94AL85000.

Influence of Clay Content, Mineralogy and Fabric On Radar Frequency Response of Aquifer Materials

NASA Astrophysics Data System (ADS)

West, L. J.; Handley, K.

High frequency electromagnetic methods such as ground penetrating radar (GPR) and time domain reflectometry (TDR) are widely employed to measure water saturation in the vadose zone and water filled porosity in the saturated zone. However, previous work has shown that radar frequency dielectric properties are strongly influenced by clay as well as by water content. They have also shown that that the dielectric response of clay minerals is strongly frequency dependent, and that even a small proportion of clay such as that present in many sandstone aquifers can have a large effect at typi- cal GPR frequencies (around 100MHz). Hence accurate water content/porosity deter- mination requires clay type and content to be taken into account. Reported here are dielectric measurements on clay-sand mixtures, aimed at investigating the influence of clay mineralogy, particle shape, and the geometrical arrangement of the mixture constituents on GPR and TDR response. Dielectric permittivity (at 50-1000MHz) was measured for mixtures of Ottawa Sand and various clay minerals or clay size quartz rock flour, using a specially constructed dielectric cell. Both homogeneous and layered mixtures were tested. The influence of pore water salinity, clay type, and particle arrangement on the dielectric response is interpreted in terms of dielectric dispersion mechanisms. The appropriateness of var- ious dielectric mixing rules such as the Complex Refractive Index Method (CRIM) for determination of water content or porosity from field GPR and TDR data are dis- cussed.

Middle-Late Pleistocene marine terraces and fault activity in the Sant'Agata di Militello coastal area (north-eastern Sicily)

NASA Astrophysics Data System (ADS)

Giunta, Giuseppe; Gueli, Anna M.; Monaco, Carmelo; Orioli, Silvia; Ristuccia, Gloria M.; Stella, Giuseppe; Troja, Sebastiano O.

2012-04-01

The coastal sector of Sant'Agata di Militello (north-eastern Sicily) is characterized by a flight of raised Middle-Upper Pleistocene marine terraces occurring at different heights with respect to present sea level. In particular, the geomorphological survey and the analysis of stereo-pairs of aerial photographs allowed to recognize at least five main orders of well preserved Quaternary surfaces and relative deposits mostly located at the hanging wall and at the footwall of the Pleistocene northwest-dipping Capo d'Orlando normal fault, which controlled the geomorphological evolution of the coastal area. The marine terraces show an overall good morphological continuity and are formed by marine platforms overlain by littoral deposits made up of yellow littoral sand and gravels in a sandy matrix. The continental sedimentary cover of the 3rd order terrace contains mammal-bearing deposits that were previously dated 200 ± 40 ka BP by isoleucine epimerization method, allowing to relate them to MIS 7.1 high-stand. In order to better define the whole terrace chronology, deposit samples were analyzed by Optically Stimulated Luminescence (OSL) methodology, a conventional SAR protocol used with sand-sized quartz. New datings, together with the detailed morphostructural analysis, allow to relate the 2nd and 4th order terraces to MIS 5.5 and 8.5, respectively, and to reconstruct the tectonic evolution of this coastal area, constraining the activity of the Capo d'Orlando fault.

Ion Diffusion Within Water Films in Unsaturated Porous Media.

PubMed

Tokunaga, Tetsu K; Finsterle, Stefan; Kim, Yongman; Wan, Jiamin; Lanzirotti, Antonio; Newville, Matthew

2017-04-18

Diffusion is important in controlling local solute transport and reactions in unsaturated soils and geologic formations. Although it is commonly assumed that thinning of water films controls solute diffusion at low water contents, transport under these conditions is not well understood. We conducted experiments in quartz sands at low volumetric water contents (θ) to quantify ion diffusion within adsorbed films. At the lowest water contents, we employed fixed relative humidities to control water films at nm thicknesses. Diffusion profiles for Rb + and Br - in unsaturated sand packs were measured with a synchrotron X-ray microprobe, and inverse modeling was used to determine effective diffusion coefficients, D e, as low as ∼9 × 10 -15 m 2 s -1 at θ = 1.0 × 10 -4 m 3 m -3 , where the film thickness = 0.9 nm. Given that the diffusion coefficients (D o ) of Rb + and Br - in bulk water (30 °C) are both ∼2.4 × 10 -9 m 2 s -1 , we found the impedance factor f = D e /(θD o ) is equal to 0.03 ± 0.02 at this very low saturation, in agreement with the predicted influence of interface tortuosity (τ a ) for diffusion along grain surfaces. Thus, reduced cross-sectional area (θ) and tortuosity largely accounted for the more than 5 orders of magnitude decrease in D e relative to D o as desaturation progressed down to nanoscale films.

Geologic map of the greater Denver area, Front Range urban corridor, Colorado

USGS Publications Warehouse

Trimble, Donald E.; Machette, Michael N.

1979-01-01

This digital map shows the areal extent of surficial deposits and rock stratigraphic units (formations) as compiled by Trimble and Machette from 1973 to 1977 and published in 1979 under the Front Range Urban Corridor Geology Program. Trimble and Machette compiled their geologic map from published geologic maps and unpublished geologic mapping having varied map unit schemes. A convenient feature of the compiled map is its uniform classification of geologic units that mostly matches those of companion maps to the north (USGS I-855-G) and to the south (USGS I-857-F). Published as a color paper map, the Trimble and Machette map was intended for land-use planning in the Front Range Urban Corridor. This map recently (1997-1999) was digitized under the USGS Front Range Infrastructure Resources Project. In general, the mountainous areas in the western part of the map exhibit various igneous and metamorphic bedrock units of Precambrian age, major faults, and fault brecciation zones at the east margin (5-20 km wide) of the Front Range. The eastern and central parts of the map (Colorado Piedmont) depict a mantle of unconsolidated deposits of Quaternary age and interspersed outcroppings of Cretaceous or Tertiary-Cretaceous sedimentary bedrock. The Quaternary mantle comprises eolian deposits (quartz sand and silt), alluvium (gravel, sand, and silt of variable composition), colluvium, and a few landslides. At the mountain front, north-trending, dipping Paleozoic and Mesozoic sandstone, shale, and limestone bedrock formations form hogbacks and intervening valleys.

Electrical conductivity of lab-formed methane hydrate + sand mixtures; technical developments and new results

NASA Astrophysics Data System (ADS)

Stern, L.; Du Frane, W. L.; Weitemeyer, K. A.; Constable, S.; Roberts, J. J.

2012-12-01

Electromagnetic (EM) measurement techniques used in permafrost and marine wells show that electrical conductivity (σ) of gas-hydrate-bearing zones is typically lower than that of surrounding sediments. However, while σ has been measured on analogue materials, it has seldom been studied on methane hydrate, the most common gas hydrate in the shallow geosphere. Additional petrophysical information - such as mixing relations and/or compositions of individual components - is also needed to more accurately relate σ to quantitative estimates of gas hydrate in EM-surveyed regions. To help address these needs, we first quantified the electrical properties of lab-formed methane hydrate at geologically relevant temperatures and pressures (Du Frane et al. GRL, 2011; also AGU 2011). A high-pressure cell was constructed to form hydrate from melting granular ice (made from distilled-deionized water) in the presence of pressurized CH4 gas, while measuring frequency-dependent impedance (Z) and σ. Final samples were pure, polycrystalline methane hydrate with excess CH4 gas but no excess H2O. The hydrate was then either quenched for grain-scale assessment by cryogenic SEM imaging, or dissociated in situ for further Z and σ measurement. Du Frane et al. [GRL, 2011] reported σ of methane hydrate to range from 10-5 to 10-4 S/m between -15 and 15°C, with activation energy (Ea) of 30.6 kJ/mol. In comparison, σ of the dissociated ice byproduct was ~400% higher with ~50% higher Ea. Measurements were then performed on methane hydrate mixed with known amounts of a standard quartz sand (Oklahoma #1, ~125 μm grain size) or similarly-sized silica glass beads in proportions ranging 10 to 90 vol. % relative to the hydrate phase. Several samples were dissociated at temperatures below -3°C for Z and σ measurement of the resulting ice/sand mixtures, and all samples were imaged for phase distribution. Adding sand complicated Z spectra for frequencies < 1 kHz and > 1MHz. However, the impedance at the frequency associated with the highest phase angle (typically 100 kHz) could be used to effectively isolate the electrical response of the sample from system contributions, enabling determination of σ. Surprisingly, the addition of sand, a nominal insulator, served to increase the overall σ of mixtures with sand fractions up through ~50 vol. % (i.e. those samples with well-connected methane hydrate), while Ea significantly decreased relative to single-phase methane hydrate. The reduced Ea suggests that a separate conduction mechanism operates when sand is present. One possible explanation is that ionic impurities from sand surfaces chemically diffuse into the hydrate grains, increasing their concentration of mobile charge-carrying defects. The fact that the addition of glass beads did not produce the same results supports this hypothesis. Geometrical mixing laws alone may therefore not sufficiently describe complicated mixing relationships between gas hydrate and sediment. Further tests are needed to resolve the competing effects, particularly if results are to be applied to systems that are not dominated by the presence of seawater. Work was performed under the auspices of U.S. DOE contracts DE-NT0005668 and DE-AC52-07NA27344, and DOE/USGS Interagency Agreement DE-NT0006147.

Luminescence dating of Holocene dune complexes along the shore of northern France (Picardy)

NASA Astrophysics Data System (ADS)

Lauer, Tobias; Frechen, Manfred; Meurisse-Fort, Murielle; Gosselin, Guillaume; van Vliet-Lanoë, Brigitte

2010-05-01

The Holocene dune and peat complexes along the shore of northern France (Picardy) had already been studied in detail by Meurisse et al. (2005) and Meurisse-Fort (2009). Information about the palaeodevelopment of those dune fields is hence given due to existing 14C data as well as by sedimentological and morphological analyses. Due to the results from radiocarbon dating, different types of aeolian bodies could be correlated along the Picardy coastline and a regional stratigraphic sequence could be established (Meurisse-Fort, 2009). The aim of the ongoing study is to get a higher chronological resolution for the different phases of dune activity in Picardy by luminescence dating what is a powerful tool to determine the time of last sunlight exposure of grains before burial (this information yields important information about dune movement). Samples for OSL dating were taken from dune bodies located in Tardinghen, Hardelot, Saint-Frieux and Saint-Gabriel. For dating, a single aliquot regenerative dose (SAR) protocol (Murray & Wintle 2003) is applied to coarse grained quartz. First tests concerning the signal intensity, the purity of the quartz OSL signal and the bleaching properties showed that quartz OSL dating works well for the dunes of the northern France coastline. The new luminescence ages will help to better unravel the phases of sand dune activity and stabilisation mainly controlled by climate changes and human impact. References: Meurisse, M., Van Vliet-Lanoë, B., Talon, B. & Recourt, P. (2005): Complexes dunaires et tourbeux holocènes du littoral du Nord de la France. - Geoscience, 337 : 675-684. Meurisse-Fort, M. (2009): Enregistrement haute résolution des massifs dunaires ; Manche, mer du Nord et Atlantique - Le rôle des tempêtes. Thèse de Doctorat soutenue en juin 2007, Université de Lille1. Coll. Recherches - Sciences (Sciences de la Terre). EPU-Publibook (ed.), Paris, 310 pp. Murray, A.S. & Wintle, A.G. (2003): The single aliquot regenerative dose protocol: potential for improvements in reliability. - Radiat. Meas., 37: 377-381.

Role of light and heavy minerals on natural radioactivity level of high background radiation area, Kerala, India.

PubMed

Ramasamy, V; Sundarrajan, M; Suresh, G; Paramasivam, K; Meenakshisundaram, V

2014-02-01

Natural radionuclides ((238)U, (232)Th and (40)K) concentrations and eight different radiological parameters have been analyzed for the beach sediments of Kerala with an aim of evaluating the radiation hazards. Activity concentrations ((238)U and (232)Th) and all the radiological parameters in most of the sites have higher values than recommended values. The Kerala beach sediments pose significant radiological threat to the people living in the area and tourists going to the beaches for recreation or to the sailors and fishermen involved in their activities in the study area. In order to know the light mineral characterization of the present sediments, mineralogical analysis has been carried out using Fourier transform infrared (FTIR) spectroscopic technique. The eight different minerals are identified and they are characterized. Among the various observed minerals, the minerals such as quartz, microcline feldspar, kaolinite and calcite are major minerals. The relative distribution of major minerals is determined by calculating extinction co-efficient and the values show that the amount of quartz is higher than calcite and much higher than microcline feldspar. Crystallinity index is calculated to know the crystalline nature of quartz present in the sediments. Heavy mineral separation analysis has been carried out to know the total heavy mineral (THM) percentage. This analysis revealed the presence of nine heavy minerals. The minerals such as monazite, zircon, magnetite and illmenite are predominant. Due to the rapid and extreme changes occur in highly dynamic environments of sandy beaches, quantities of major light and heavy minerals are widely varied from site to site. Granulometric analysis shows that the sand is major content. Multivariate statistical (Pearson correlation, cluster and factor) analysis has been carried out to know the effect of mineralogy on radionuclide concentrations. The present study concluded that heavy minerals induce the (238)U and (232)Th concentrations. Whereas, light mineral (calcite) controls the (40)K concentration. In addition to the heavy minerals, clay content also induces the important radioactive variables. © 2013 Published by Elsevier Ltd.

The Role of Source Material in Basin Sedimentation, as Illustrated within Eureka Valley, Death Valley National Park, CA.

NASA Astrophysics Data System (ADS)

Lawson, M. J.; Yin, A.; Rhodes, E. J.

2015-12-01

Steep landscapes are known to provide sediment to sink regions, but often petrological factors can dominate basin sedimentation. Within Eureka Valley, in northwestern Death Valley National Park, normal faulting has exposed a steep cliff face on the western margin of the Last Chance range with four kilometers of vertical relief from the valley floor and an angle of repose of nearly 38 degrees. The cliff face is composed of Cambrian limestone and dolomite, including the Bonanza King, Carrara and Wood Canyon formations. Interacting with local normal faulting, these units preferentially break off the cliff face in coherent blocks, which result in landslide deposits rather than as finer grained material found within the basin. The valley is well known for a large sand dune, which derives its sediment from distal sources to the north, instead of from the adjacent Last Chance Range cliff face. During the Holocene, sediment is sourced primary from the northerly Willow Wash and Cucomungo canyon, a relatively small drainage (less than 80 km2) within the Sylvan Mountains. Within this drainage, the Jurassic quartz monzonite of Beer Creek is heavily fractured due to motion of the Fish Valley Lake - Death Valley fault zone. Thus, the quartz monzonite is more easily eroded than the well-consolidated limestone and dolomite that forms the Last Change Range cliff face. As well, the resultant eroded material is smaller grained, and thus more easily transported than the limestone. Consequently, this work highlights an excellent example of the strong influence that source material can have on basin sedimentation.

Identification and characterization of tsunami deposits off southeast coast of India from the 2004 Indian Ocean tsunami: Rock magnetic and geochemical approach

NASA Astrophysics Data System (ADS)

Veerasingam, S.; Venkatachalapathy, R.; Basavaiah, N.; Ramkumar, T.; Venkatramanan, S.; Deenadayalan, K.

2014-06-01

The December 2004 Indian Ocean Tsunami (IOT) had a major impact on the geomorphology and sedimentology of the east coast of India. Estimation of the magnitude of the tsunami from its deposits is a challenging topic to be developed in studies on tsunami hazard assessment. Two core sediments (C1 and C2) from Nagapattinam, southeast coast of India were subjected to textural, mineral, geochemical and rock-magnetic measurements. In both cores, three zones (zone I, II and III) have been distinguished based on mineralogical, geochemical and magnetic data. Zone II is featured by peculiar rock-magnetic, textural, mineralogical and geochemical signatures in both sediment cores that we interpret to correspond to the 2004 IOT deposit. Textural, mineralogical, geochemical and rock-magnetic investigations showed that the tsunami deposit is featured by relative enrichment in sand, quartz, feldspar, carbonate, SiO 2, TiO 2, K 2O and CaO and by a depletion in clay and iron oxides. These results point to a dilution of reworked ferromagnetic particles into a huge volume of paramagnetic materials, similar to what has been described in other nearshore tsunami deposits (Font et al. 2010). Correlation analysis elucidated the relationships among the textural, mineral, geochemical and magnetic parameters, and suggests that most of the quartz-rich coarse sediments have been transported offshore by the tsunami wave. These results agreed well with the previously published numerical model of tsunami induced sediment transport off southeast coast of India and can be used for future comparative studies on tsunami deposits.

Mixed siliciclastic and carbonate sedimentation within Spar Mountain Member of Ste. Genevieve Limestone, Hamilton County, Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, M.J.; Pryor, W.A.

1985-02-01

The Spar Mountain Member of the Ste. Genevieve Limestone (middle Mississippian) in Hamilton County, Illinois, consists of 40-60 ft (12-18 m) of interbedded limestones, shales, and sandstones. Five cores and 1400 electric logs were used to delineate two shallowing-upward carbonate cycles and 2 major clastic pulses within the Spar Mountain. Eight lithofacies representing 6 depositional environments were identified. They are: (A) echinoderm-brachiopod dolostone to packstone (outer ramp), (B) ooid-peloidal grainstone (intermediate ramp), (C) skeletal grainstone (intermediate ramp), (D) ooid-molluscan-intraclastic wackestone to grainstone (inner ramp), (E) pelletal-skeletal wackestone (inner ramp), (F) quartzarenite (channelized nearshore), (G) quartz-sublithic arenite to wacke (delta platform),more » and (H) quartz mudstone (prodelta, delta platform). Deposition occurred on a southwest-dipping carbonate ramp, with siliciclastic sediments originating from the northeast. The sequence of facies and their inferred depositional environments record 2 major progradational episodes. Oolitic facies are interpreted to be of tidal-bar belt origin and quartzarenite facies are interpreted to be of delta-distributary channel origin. Their distribution is partially controlled by antecedent and syndepositional topography. Many of these paleotopographic highes are positive features today and yield pinch-out stratigraphic relationships. Paleogeographic reconstructions demonstrate that the primary control on facies distribution was the position of the delta proper along strike. However, depositional topography also influenced sedimentation, particularly in the sand-sized fraction. Using this concept, better prediction of underlying porous buildups (ooid shoals) is possible if thickness of the overlying siliciclastic is known. Within buildups, a complex diagenetic history complicates the distribution of porosity.« less

Experimental heat treatment of silcrete implies analogical reasoning in the Middle Stone Age.

PubMed

Wadley, Lyn; Prinsloo, Linda C

2014-05-01

Siliceous rocks that were not heated to high temperatures during their geological formation display improved knapping qualities when they are subjected to controlled heating. Experimental heat treatment of South African silcrete, using open fires of the kind used during the Middle Stone Age, shows that the process needed careful management, notwithstanding recent arguments to the contrary. Silcrete blocks fractured when heated on the surface of open fires or on coal beds, but were heated without mishap when buried in sand below a fire. Three silcrete samples, a control, a block heated underground with maximum temperature between 400 and 500 °C and a block heated in an open fire with maximum temperature between 700 and 800 °C, were analysed with X-ray powder diffraction (XRD), X-ray fluorescence (XRF), optical microscopy, and both Fourier transform infrared (FTIR) and Raman spectroscopy. The results show that the volume expansion during the thermally induced α- to β-quartz phase transformation and the volume contraction during cooling play a major role in the heat treatment of silcrete. Rapid heating or cooling through the phase transformation at 573 °C will cause fracture of the silcrete. Successful heat treatment requires controlling surface fire temperatures in order to obtain the appropriate underground temperatures to stay below the quartz inversion temperature. Heat treatment of rocks is a transformative technology that requires skilled use of fire. This process involves analogical reasoning, which is an attribute of complex cognition. Copyright © 2014 Elsevier Ltd. All rights reserved.

Direct Measurement of the Wettability of Minerals Using Atomic Force Microscopy

NASA Astrophysics Data System (ADS)

Deng, Y.; Xu, L.; Lu, H.; Wang, H.; Shi, Y.

2016-12-01

The wettability of reservoir rock plays an essential role in affecting the states of fluids (water, oil, etc) in pores which are constructed with various minerals. The contact angle method, which is based on the optical microscope photographs of millimeter-sized droplets on a smooth mineral surface, is one of the most widely employed methods to evaluate the wettability of a rock. However, the real reservoir rocks are composed of several kinds of minerals and thus nonhomogeneous, which leads to different wettability at different location of the rock. The mineral grains are usually micrometer-sized so that the traditional optical contact angle method cannot obtain the wettability of different minerals in the rock. Here we used a tapping-mode atomic force microscopy (TM-AFM, MFP-3D-BIO, Asylum Research) to measure the contact angles of micrometer-sized water droplets on different minerals in a tight sand rock which is mainly composed of quartz, albite, potash feldspar and anorthite. The water droplets varied from submicron to several tens micron in diameter. With the optimization of tool and operation parameters, the AFM tip was well controlled so that the nanoscale morphology of the contact configuration between water film and the mineral surface can be obtained at high resolution without disturbing the liquid surface. The AFM results showed that the contact angles of water on quartz and albite were 30-40 ° and 37-45 °, respectively. The AFM method provides a new measure for the wettability evaluation of reservoir rocks, and it is with potential to be applied to oil and gas hydrate studies.

Thermal signature characteristics of vehicle/terrain interaction disturbances: implications for battlefield vehicle classification.

PubMed

Eastes, John W; Mason, George L; Kusinger, Alan E

2004-05-01

Thermal emissivity spectra (8-14 microm) of track impressions/background were determined in conjunction with operation of six military vehicle types, T-72 and M1 Tanks, an M2 Bradley Fighting Vehicle, a 5-ton truck, a D7 tractor, and a High Mobility Multipurpose Wheeled Vehicle (HMMWV), over diverse soil surfaces to determine if vehicle type could be related to track thermal signatures. Results suggest soil compaction and fragmentation/pulverization are primary parameters affecting track signatures and that soil and vehicle/terrain-contact type determine which parameter dominates. Steel-tracked vehicles exert relatively low ground-contact pressure but tend to fragment/pulverize soil more so than do rubber-tired vehicles, which tend mainly to compact. In quartz-rich, lean clay soil tracked vehicles produced impressions with spectral contrast of the quartz reststrahlen features decreased from that of the background. At the same time, 5-ton truck tracks exhibited increased contrast on the same surface, suggesting that steel tracks fragmented soil while rubber tires mainly produced compaction. The structure of materials such as sand and moist clay-rich river sediment makes them less subject to further fragmentation/pulverization; thus, compaction was the main factor affecting signatures in these media, and both tracked and wheeled vehicles created impressions with increased spectral contrast on these surfaces. These results suggest that remotely sensed thermal signatures could differentiate tracked and wheeled vehicles on terrain in many areas of the world of strategic interest. Significant applications include distinguishing visually/spectrally identical lightweight decoys from actual threat vehicles.

U.S. Geological survey program on toxic waste--ground-water contamination; proceedings of the Second technical meeting, Cape Cod, Massachusetts, October 21-25, 1985

USGS Publications Warehouse

Ragone, S.E.

1988-01-01

This study characterizes the clay minerals in sediments associated with a plume of creosote-contaminated groundwater. The plume of contaminated groundwater near Pensacola, FL, is in shallow, permeable, Miocene to Holocene quartz sand and flows southward toward Pensacola Bay. Clay-size fractions were separated from 41 cores, chiefly split-spoon samples at 13 drill sites. The most striking feature of the chemical analyses of the clay fractions from uncontaminated site 2 and contaminated sites 4,5,6, and 7 is the variability of iron oxide (species in some samples as Fe2O3); total iron oxide abundance is lowest (2.5%) in uncontaminated sample 2-40, but is > 4.5% (4.5 to 8.5%) in the remaining assemblages. One feature suggesting interaction between the indigenous clays and the waste plume is the presence of nontronite-rich smectite. Nontronite commonly has been identified as the product of hydrothermal alteration and deep-sea weathering of submarine basalts; it is not a common constituent of Cenozoic Gulf Coast sediments. At the Pensacola site, relatively abundant nontronitic smectite is confined to contaminated sands or associated muds; it is least abundant or absent in sands and muds peripheral to the waste plume. The geochemistry of the waste plume, its substantial dissolved, (chiefly ferrous iron), mildly acidic (pH 5-6), and low redox composition, provides an environment similar to that previously determined for the low-temperature synthesis of nontronite. Data from clay-size fractions confirm conclusions that neoformed pyrite in some grain coatings occurs in an assemblage with excess iron over that required in the pyrite. Continuing studies to evaluate these tentative conclusions include: (1) chemical analysis of clay fractions from remaining sites to further examine the apparent relation between iron content and abundance of nontronitic smectite; (2) clay separation and analysis, and pore fluid extraction (squeezing or ultracentrifugation) and analysis from a continuous core through the mud lens to determine pore fluid composition (presence or absence of waste fluid), and character of associated clay minerals; and (3) clay separation and analysis in both permeable sands and the intervening mud lens that are clearly outside the limits of the waste plume to further document the effects of the plume. (See also W90-00022) (Lantz-PTT)

Effect of the particle to fluid density ratio on bedform development: An application of PTV

NASA Astrophysics Data System (ADS)

McKenna Neuman, C. L.; Gordon, M. D.

2009-05-01

The particle to fluid density ratio plays a key role in sediment transport and strongly governs the relative importance of the transport mode. In aeolian systems, this ratio is three orders of magnitude larger than for the transport of sedimentary particles in water, such that saltation is the dominant mode for diameters (250 microns) commonly found in ripples and dunes. The partitioning of fluid momentum to saltators, and therefore to the surface upon impact, is extremely important to the entrainment of sediment, the maintenance of transport, and the scaling of aeolian bedforms. This paper demonstrates the use of Particle Tracking Velocimetry in measuring the partitioning of momentum associated with particle collisions on beds of quartz sand (2630 kg m-3) typical of aeolian dunes, and acrylic particles (1210 kg m-3) similar to blowing snow (920 kg m-3). The experiments were carried out in the boundary layer wind tunnel at Trent University on full beds that were 13.8 m in length and 0.71 m in width. In the majority of experiments, the wind speeds were either at or just above the threshold for saltation so that we could distinguish discrete particle trajectories. Surface ripples formed in the majority of experiments and passed through the camera's field of view so that the height, length and rate of migration could be measured in relation to the distributions of particle impact speed and angle, as well as those for the number, speed and angle of the particles ejected. Although similar in height, the ripples comprised of acrylic particles were 2 to 4 times longer, much more asymmetric, and migrated significantly faster than those in sand. The particle impact and ejection speeds were very similar, although the sand particles approached and left the bed at substantially larger angles than observed for the lighter acrylic particles of similar diameter. In a separate experiment, glass beads were flung onto each bed material at 4 ms-1 in still air. It was discovered that 90 per cent of the impact energy was lost to the acrylic bed, as compared to 78 per cent for the sand bed. This evidence suggests that at smaller density ratios than investigated here, ballistic ripples likely cannot be maintained in air.

Physical and chemical effects of grain aggregates on the Palos Verdes margin, southern California

USGS Publications Warehouse

Drake, D.E.; Eganhouse, R.; McArthur, W.

2002-01-01

Large discharges of wastewater and particulate matter from the outfalls of the Los Angeles County Sanitation Districts onto the Palos Verdes shelf since 1937 have produced an effluent-affected sediment deposit characterized by low bulk density, elevated organic matter content, and a high percentage of fine silt and clay particles relative to underlying native sands and sandy silts. Comparison of the results of grain-size analyses using a gentle wet-sieving technique that preserves certain grain aggregates to the results of standard size analyses of disaggregated particles shows that high percentages (up to 50%) of the silt and clay fractions of the effluent-affected mud are incorporated in aggregates having intermediate diameters in the fine-to-medium sand size range (63-500 ??m), Scanning electron microscope images of the aggregates show that they are predominantly oval fecal pellets or irregularly shaped fragments of pellets. Deposit-feeding polychaete worms such as Capitella sp. and Mediomastus sp., abundant in the mud-rich effluent-affected sediment on Palos Verdes shelf, are probably responsible for most of the grain aggregates through fecal pellet production. Particle settling rates and densities, and the concentrations of organic carbon and p,p???-DDE, a metabolite of the hydrophobic pesticide DDT, were determined for seven grain-size fractions in the effluent-affected sediment. Fecal pellet grain densities ranged from about 1.2 to 1.5 g/cc, and their average settling rates were reduced to the equivalent of about one phi size relative to spherical quartz grains of the same diameter. However, repackaging of fine silt and clay grains into the sand-sized fecal pellets causes an effective settling rate increase of up to 3 orders of magnitude for the smallest particles incorporated in the pellets. Moreover, organic carbon and p,p???-DDE exhibit a bimodal distribution with relatively high concentrations in the finest size fraction (0-20 ??m), as expected, and a second concentration peak associated with the sand-sized fecal pellets. The repackaging of fine-grained particles along with their adsorbed chemical compounds into relatively fast-settling pellets has important implications for the mobilization and transport of the sediment and the desorption of chemicals from grain surfaces. ?? 2002 Published by Elsevier Science Ltd.

Surficial Geologic Map of the Evansville, Indiana, and Henderson, Kentucky, Area

USGS Publications Warehouse

Moore, David W.; Lundstrom, Scott C.; Counts, Ronald C.; Martin, Steven L.; Andrews, William M.; Newell, Wayne L.; Murphy, Michael L.; Thompson, Mark F.; Taylor, Emily M.; Kvale, Erik P.; Brandt, Theodore R.

2009-01-01

The geologic map of the Evansville, Indiana, and Henderson, Kentucky, area depicts and describes surficial deposits according to their origin and age. Unconsolidated alluvium and outwash fill the Ohio River bedrock valley and attain maximum thickness of 33-39 m under Diamond Island, Kentucky, and Griffith Slough, south of Newburgh, Indiana. The fill is chiefly unconsolidated, fine- to medium-grained, lithic quartz sand, interbedded with clay, clayey silt, silt, coarse sand, granules, and gravel. Generally, the valley fill fines upward from the buried bedrock surface: a lower part being gravelly sand to sandy gravel, a middle part mostly of sand, and a surficial veneer of silt and clay interspersed with sandy, natural levee deposits at river's edge. Beneath the unconsolidated fill are buried and discontinuous, lesser amounts of consolidated fill unconformably overlying the buried bedrock surface. Most of the glaciofluvial valley fill accumulated during the Wisconsin Episode (late Pleistocene). Other units depicted on the map include creek alluvium, slackwater lake (lacustrine) deposits, colluvium, dune sand, loess, and sparse bedrock outcrops. Creek alluvium underlies creek floodplains and consists of silt, clayey silt, and subordinate interbedded fine sand, granules, and pebbles. Lenses and beds of clay are present locally. Silty and clayey slackwater lake (lacustrine) deposits extensively underlie broad flats northeast of Evansville and around Henderson and are as thick as 28 m. Fossil wood collected from an auger hole in the lake and alluvial deposits of Little Creek, at depths of 10.6 m and 6.4 m, are dated 16,650+-50 and 11,120+-40 radiocarbon years, respectively. Fossil wood collected from lake sediment 16 m below the surface in lake sediment was dated 33,100+-590 radiocarbon years. Covering the hilly bedrock upland is loess (Qel), 3-7.5 m thick in Indiana and 9-15 m thick in Kentucky, deposited about 22,000-12,000 years before present. Most mapped surficial deposits in the quadrangle are probably no older than about 55,000 years. Lithologic logs, shear-wave velocities, and other cone penetrometer data are used to interpret depositional environments and geologic history of the surficial deposits. This map, which includes an area of slightly more than seven 7.5-minute quadrangles, serves several purposes. It is a tool for assessing seismic and flood hazards of a major urban area; aids urban planning; conveys geologic history; and locates aggregate resources. The map was produced concurrently with research by seismologists to determine places where the surficial deposits may tend to liquefy and (or) to amplify ground motions during strong earthquakes. Such hazardous responses to shaking are related to the characteristics of the geologic materials and topographic position, which the geologic map depicts. The geologic map is an element in the cooperative seismic hazard assessment program among the States of Indiana, Kentucky, and Illinois and the U.S. Geological Survey, funded by the National Earthquake Hazards Reduction Program and National Cooperative Geologic Mapping Program of the U.S. Geological Survey.

How does the wetting dynamics affect capillary trapping in heterogeneous soil: Neutron imaging study

NASA Astrophysics Data System (ADS)

Sacha, Jan; Snehota, Michal; Trtik, Pavel; Vontobel, Peter

2017-04-01

The wetting dynamics of the water infiltration into a porous soil system has a strong influence on the amount of entrapped air inside the soil. Simultaneously, a higher volume of entrapped air obstructs a water flow in the medium. This effect is more noticeable in soils with preferential pathways because the soil matrix has a higher capillary forces and therefore the air is accumulated in preferential pathways. In the presented study, two experiments were conducted on the same sample. The first experiment was performed under the constant water level condition (CWL) and the second experiment was carried out under the constant water flux condition (CWF) at the top of the sample. The sample was composed of coarse and medium coarse fractions of sand and fine porous ceramics. Materials were packed into the quartz glass column of the inner diameter of 29 mm. The coarse sand represented a highly conductive region connected from the top to the bottom of the sample with the exception of three thin (2-3 mm) separation layers made up of the medium coarse sand. Three discs of fine ceramics formed slow flow regions. Infiltration experiments were monitored by neutron radiography at two different beamlines to produce two-dimensional (2D) projections. The CWL experiment was monitored at NEUTRA station with an acquisition time of 16 seconds per projection and the CWF experiment was visualized at BOA station with an acquisition time of 0.25 seconds per projection. Both stations are located at the Paul Scherrer Institut, Switzerland. The acquired radiograms of the dry sample were subtracted from all subsequent radiograms to determine the water thickness in projections. From series of corrected radiograms taken at the different angles three-dimensional (3D) image was reconstructed for steady state stage of the CWL experiment and for the entire CWF experiment. Then the series of 3D images mapped the wetting of the porous system over the corresponding phase of infiltration process. The results show a higher steady state infiltration rate during the CWL experiment. In this case, the air was mostly pushed out from the sample by the moving wetting front. The infiltration rate was continuously decreasing during the infiltration up to the value of steady state infiltration rate. When the wetting front has reached the bottom of the sample the air was moving from matrix domain to preferential domain. Infiltration rate was still higher than during CWF. On the contrary, during the CWF the water infiltrated into the fine ceramics first and then into the medium coarse sand attracted by forces that were stronger in comparison to the coarse sand. Due to this effect a significant amount of air was trapped in preferential pathways, and consequently blocked the water flow primarily due to the presence of medium coarse sand regions.

A straightforward method for measuring the range of apparent density of microplastics.

PubMed

Li, Lingyun; Li, Mengmeng; Deng, Hua; Cai, Li; Cai, Huiwen; Yan, Beizhan; Hu, Jun; Shi, Huahong

2018-10-15

Density of microplastics has been regarded as the primary property that affect the distribution and bioavailability of microplastics in the water column. For measuring the density of microplastis, we developed a simple and rapid method based on density gradient solutions. In this study, we tested four solvents to make the density gradient solutions, i.e., ethanol (0.8 g/cm 3 ), ultrapure water (1.0 g/cm 3 ), saturated NaI (1.8 g/cm 3 ) and ZnCl 2 (1.8 g/cm 3 ). Density of microplastics was measured via observing the float or sink status in the density gradient solutions. We found that density gradient solutions made from ZnCl 2 had a larger uncertainty in measuring density than that from NaI, most likely due to a higher surface tension of ZnCl 2 solution. Solutions made from ethanol, ultrapure water, and NaI showed consistent density results with listed densities of commercial products, indicating that these density gradient solutions were suitable for measuring microplastics with a density range of 0.8-1.8 g/cm 3 . Copyright © 2018 Elsevier B.V. All rights reserved.

Ultrasensitive and selective gold film-based detection of mercury (II) in tap water using a laser scanning confocal imaging-surface plasmon resonance system in real time.

PubMed

Zhang, Hongyan; Yang, Liquan; Zhou, Bingjiang; Liu, Weimin; Ge, Jiechao; Wu, Jiasheng; Wang, Ying; Wang, Pengfei

2013-09-15

An ultrasensitive and selective detection of mercury (II) was investigated using a laser scanning confocal imaging-surface plasmon resonance system (LSCI-SPR). The detection limit was as low as 0.01ng/ml for Hg(2+) ions in ultrapure and tap water based on a T-rich, single-stranded DNA (ssDNA)-modified gold film, which can be individually manipulated using specific T-Hg(2+)-T complex formation. The quenching intensity of the fluorescence images for rhodamine-labeled ssDNA fitted well with the changes in SPR. The changes varied with the Hg(2+) ion concentration, which is unaffected by the presence of other metal ions. The coefficients obtained for ultrapure and tap water were 0.99902 and 0.99512, respectively, for the linear part over a range of 0.01-100ng/ml. The results show that the double-effect sensor has potential for practical applications with ultra sensitivity and selectivity, especially in online or real-time monitoring of Hg(2+) ions pollution in tap water with the further improvement of portable LSCI-SPR instrument. Copyright © 2013 Elsevier B.V. All rights reserved.

The release of nickel from orthodontic NiTi wires is increased by dynamic mechanical loading but not constrained by surface nitridation.

PubMed

Peitsch, T; Klocke, A; Kahl-Nieke, B; Prymak, O; Epple, M

2007-09-01

The influence of dynamic mechanical loading and of surface nitridation on the nickel release from superelastic nickel-titanium orthodontic wires was investigated under ultrapure conditions. Commercially available superelastic NiTi arch wires (size 0.018 x 0.025'') without surface modification (Neo Sentalloy) and with nitrogen ion implantation surface treatment (Neo Sentalloy Ionguard) were analyzed. Mechanical loading of wire segments with a force similar to the physiological situation was performed with a frequency of 5 Hz in ultrapure water and saline solution, respectively. The release of nickel was monitored by atomic absorption spectroscopy for up to 36 days. The mechanically loaded wires released significantly more nickel ( approximately 45 ng cm(-2) d(-1)) than did nonloaded wires (<1 ng cm(-2) d(-1)). There was no statistically significant effect of the testing solution (water or NaCl) or of the surface nitridation. The total amount of released nickel was small in all cases, but may nevertheless account for the occasional clinical observations of adverse reactions during application of NiTi-based orthodontic appliances. The surface nitridation did not constrain the release of nickel from NiTi under continuous mechanical stress.

Approaching behavior of a pair of spherical bubbles in quiescent liquids

NASA Astrophysics Data System (ADS)

Sanada, Toshiyuki; Kusuno, Hiroaki

2015-11-01

Some unique motions related bubble-bubble interaction, such as equilibrium distance, wake induced lift force, have been proposed by theoretical analysis or numerical simulations. These motions are different from the solid spheres like DKT model (Drafting, Kissing and Tumbling). However, there is a lack of the experimental verification. In this study, we experimentally investigated the motion of a pair of bubbles initially positioned in-line configuration in ultrapure water or an aqueous surfactant solution. The bubble motion were observed by two high speed video cameras. The bubbles Reynolds number was ranged from 50 to 300 and bubbles hold the spherical shape in this range. In ultrapure water, initially the trailing bubble deviated from the vertical line on the leading bubble owing to the wake of the leading bubble. And then, the slight difference of the bubble radius changed the relative motion. When the trailing bubble slightly larger than the leading bubble, the trailing bubble approached to the leading bubble due to it's buoyancy difference. The bubbles attracted and collided only when the bubbles rising approximately side by side configuration. In addition, we will also discuss the motion of bubbles rising in an aqueous surfactant solution.

Fabrication and characterisation of ligand-functionalised ultrapure monodispersed metal nanoparticle nanoassemblies employing advanced gas deposition technique

NASA Astrophysics Data System (ADS)

Geremariam Welearegay, Tesfalem; Cindemir, Umut; Österlund, Lars; Ionescu, Radu

2018-02-01

Here, we report for the first time the fabrication of ligand-functionalised ultrapure monodispersed metal nanoparticles (Au, Cu, and Pt) from their pure metal precursors using the advanced gas deposition technique. The experimental conditions during nanoparticle formation were adjusted in order to obtain ultrafine isolated nanoparticles on different substrates. The morphology and surface analysis of the as-deposited metal nanoparticles were investigated using scanning electron microscopy, x-ray diffraction and Fourier transform infra-red spectroscopy, which demonstrated the formation of highly ordered pure crystalline nanoparticles with a relatively uniform size distribution of ∼10 nm (Au), ∼4 nm (Cu) and ∼3 nm (Pt), respectively. A broad range of organic ligands containing thiol or amine functional groups were attached to the nanoparticles to form continuous networks of nanoparticle-ligand nanoassemblies, which were characterised by scanning electron microscopy and x-ray photoelectron spectroscopy. The electrical resistance of the functional nanoassemblies deposited in the gap spacing of two microfabricated parallel Au electrodes patterned on silicon substrates ranged between tens of kΩ and tens of MΩ, which is suitable for use in many applications including (bio)chemical sensors, surface-enhanced Raman spectroscopy and molecular electronic rectifiers.