Noninvasive and Real-Time Plasmon Waveguide Resonance Thermometry

PubMed Central

Zhang, Pengfei; Liu, Le; He, Yonghong; Zhou, Yanfei; Ji, Yanhong; Ma, Hui

2015-01-01

In this paper, the noninvasive and real-time plasmon waveguide resonance (PWR) thermometry is reported theoretically and demonstrated experimentally. Owing to the enhanced evanescent field and thermal shield effect of its dielectric layer, a PWR thermometer permits accurate temperature sensing and has a wide dynamic range. A temperature measurement sensitivity of 9.4 × 10−3 °C is achieved and the thermo optic coefficient nonlinearity is measured in the experiment. The measurement of water cooling processes distributed in one dimension reveals that a PWR thermometer allows real-time temperature sensing and has potential to be applied for thermal gradient analysis. Apart from this, the PWR thermometer has the advantages of low cost and simple structure, since our transduction scheme can be constructed with conventional optical components and commercial coating techniques. PMID:25871718

Structural Integrity of Water Reactor Pressure Boundary Components.

DTIC Science & Technology

1981-02-20

environment, and load waveform parameters . A theory of the influence of dissolved oxygen content on the fatigue crack growth results in simulated PWR ...simulated PWR coolant is - (Continues ) DD IJN7 1473 EDITION OF I NOV S ..OSL- -C 2 S/ 0102-LF-014-6601 S1ECURITY CLASSI1FICATION OF THIS PAGE (When...not seem to influence the data, which was produced for a load ratio of 0.2 and a simulated PWR coolant environment. Test results for A106 Grade C piping

Coupled Neutronics Thermal-Hydraulic Solution of a Full-Core PWR Using VERA-CS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clarno, Kevin T; Palmtag, Scott; Davidson, Gregory G

2014-01-01

The Consortium for Advanced Simulation of Light Water Reactors (CASL) is developing a core simulator called VERA-CS to model operating PWR reactors with high resolution. This paper describes how the development of VERA-CS is being driven by a set of progression benchmark problems that specify the delivery of useful capability in discrete steps. As part of this development, this paper will describe the current capability of VERA-CS to perform a multiphysics simulation of an operating PWR at Hot Full Power (HFP) conditions using a set of existing computer codes coupled together in a novel method. Results for several single-assembly casesmore » are shown that demonstrate coupling for different boron concentrations and power levels. Finally, high-resolution results are shown for a full-core PWR reactor modeled in quarter-symmetry.« less

Identification of poor households for premium exemptions in Ghana's National Health Insurance Scheme: empirical analysis of three strategies.

PubMed

Aryeetey, Genevieve Cecilia; Jehu-Appiah, Caroline; Spaan, Ernst; D'Exelle, Ben; Agyepong, Irene; Baltussen, Rob

2010-12-01

To evaluate the effectiveness of three alternative strategies to identify poor households: means testing (MT), proxy means testing (PMT) and participatory wealth ranking (PWR) in urban, rural and semi-urban settings in Ghana. The primary motivation was to inform implementation of the National Health Insurance policy of premium exemptions for the poorest households. Survey of 145-147 households per setting to collect data on consumption expenditure to estimate MT measures and of household assets to estimate PMT measures. We organized focus group discussions to derive PWR measures. We compared errors of inclusion and exclusion of PMT and PWR relative to MT, the latter being considered the gold standard measure to identify poor households. Compared to MT, the errors of exclusion and inclusion of PMT ranged between 0.46-0.63 and 0.21-0.36, respectively, and of PWR between 0.03-0.73 and 0.17-0.60, respectively, depending on the setting. Proxy means testing and PWR have considerable errors of exclusion and inclusion in comparison with MT. PWR is a subjective measure of poverty and has appeal because it reflects community's perceptions on poverty. However, as its definition of the poor varies across settings, its acceptability as a uniform strategy to identify the poor in Ghana may be questionable. PMT and MT are potential strategies to identify the poor, and their relative societal attractiveness should be judged in a broader economic analysis. This study also holds relevance to other programmes that require identification of the poor in low-income countries. © 2010 Blackwell Publishing Ltd.

Evaluation of a Powered Ankle-Foot Prosthesis during Slope Ascent Gait

PubMed Central

2016-01-01

Passive prosthetic feet lack active plantarflexion and push-off power resulting in gait deviations and compensations by individuals with transtibial amputation (TTA) during slope ascent. We sought to determine the effect of active ankle plantarflexion and push-off power provided by a powered prosthetic ankle-foot (PWR) on lower extremity compensations in individuals with unilateral TTA as they walked up a slope. We hypothesized that increased ankle plantarflexion and push-off power would reduce compensations commonly observed with a passive, energy-storing-returning prosthetic ankle-foot (ESR). We compared the temporal spatial, kinematic, and kinetic measures of ten individuals with TTA (age: 30.2 ± 5.3 yrs) to matched abled-bodied (AB) individuals during 5° slope ascent. The TTA group walked with an ESR and separately with a PWR. The PWR produced significantly greater prosthetic ankle plantarflexion and push-off power generation compared to an ESR and more closely matched AB values. The PWR functioned similar to a passive ESR device when transitioning onto the prosthetic limb due to limited prosthetic dorsiflexion, which resulted in similar deviations and compensations. In contrast, when transitioning off the prosthetic limb, increased ankle plantarflexion and push-off power provided by the PWR contributed to decreased intact limb knee extensor power production, lessening demand on the intact limb knee. PMID:27977681

Evaluation of a Powered Ankle-Foot Prosthesis during Slope Ascent Gait.

PubMed

Rábago, Christopher A; Aldridge Whitehead, Jennifer; Wilken, Jason M

2016-01-01

Passive prosthetic feet lack active plantarflexion and push-off power resulting in gait deviations and compensations by individuals with transtibial amputation (TTA) during slope ascent. We sought to determine the effect of active ankle plantarflexion and push-off power provided by a powered prosthetic ankle-foot (PWR) on lower extremity compensations in individuals with unilateral TTA as they walked up a slope. We hypothesized that increased ankle plantarflexion and push-off power would reduce compensations commonly observed with a passive, energy-storing-returning prosthetic ankle-foot (ESR). We compared the temporal spatial, kinematic, and kinetic measures of ten individuals with TTA (age: 30.2 ± 5.3 yrs) to matched abled-bodied (AB) individuals during 5° slope ascent. The TTA group walked with an ESR and separately with a PWR. The PWR produced significantly greater prosthetic ankle plantarflexion and push-off power generation compared to an ESR and more closely matched AB values. The PWR functioned similar to a passive ESR device when transitioning onto the prosthetic limb due to limited prosthetic dorsiflexion, which resulted in similar deviations and compensations. In contrast, when transitioning off the prosthetic limb, increased ankle plantarflexion and push-off power provided by the PWR contributed to decreased intact limb knee extensor power production, lessening demand on the intact limb knee.

Multirecycling of Plutonium from LMFBR Blanket in Standard PWRs Loaded with MOX Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sonat Sen; Gilles Youinou

2013-02-01

It is now well-known that, from a physics standpoint, Pu, or even TRU (i.e. Pu+M.A.), originating from LEU fuel irradiated in PWRs can be multirecycled also in PWRs using MOX fuel. However, the degradation of the isotopic composition during irradiation necessitates using enriched U in conjunction with the MOX fuel either homogeneously or heterogeneously to maintain the Pu (or TRU) content at a level allowing safe operation of the reactor, i.e. below about 10%. The study is related to another possible utilization of the excess Pu produced in the blanket of a LMFBR, namely in a PWR(MOX). In this casemore » the more Pu is bred in the LMFBR, the more PWR(MOX) it can sustain. The important difference between the Pu coming from the blanket of a LMFBR and that coming from a PWR(LEU) is its isotopic composition. The first one contains about 95% of fissile isotopes whereas the second one contains only about 65% of fissile isotopes. As it will be shown later, this difference allows the PWR fed by Pu from the LMFBR blanket to operate with natural U instead of enriched U when it is fed by Pu from PWR(LEU)« less

Performance evaluation of two-stage fuel cycle from SFR to PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fei, T.; Hoffman, E.A.; Kim, T.K.

2013-07-01

One potential fuel cycle option being considered is a two-stage fuel cycle system involving the continuous recycle of transuranics in a fast reactor and the use of bred plutonium in a thermal reactor. The first stage is a Sodium-cooled Fast Reactor (SFR) fuel cycle with metallic U-TRU-Zr fuel. The SFRs need to have a breeding ratio greater than 1.0 in order to produce fissile material for use in the second stage. The second stage is a PWR fuel cycle with uranium and plutonium mixed oxide fuel based on the design and performance of the current state-of-the-art commercial PWRs with anmore » average discharge burnup of 50 MWd/kgHM. This paper evaluates the possibility of this fuel cycle option and discusses its fuel cycle performance characteristics. The study focuses on an equilibrium stage of the fuel cycle. Results indicate that, in order to avoid a positive coolant void reactivity feedback in the stage-2 PWR, the reactor requires high quality of plutonium from the first stage and minor actinides in the discharge fuel of the PWR needs to be separated and sent back to the stage-1 SFR. The electricity-sharing ratio between the 2 stages is 87.0% (SFR) to 13.0% (PWR) for a TRU inventory ratio (the mass of TRU in the discharge fuel divided by the mass of TRU in the fresh fuel) of 1.06. A sensitivity study indicated that by increasing the TRU inventory ratio to 1.13, The electricity generation fraction of stage-2 PWR is increased to 28.9%. The two-stage fuel cycle system considered in this study was found to provide a high uranium utilization (>80%). (authors)« less

Association between gestational weight gain according to body mass index and postpartum weight in a large cohort of Danish women.

PubMed

Rode, Line; Kjærgaard, Hanne; Ottesen, Bent; Damm, Peter; Hegaard, Hanne K

2012-02-01

Our aim was to investigate the association between gestational weight gain (GWG) and postpartum weight retention (PWR) in pre-pregnancy underweight, normal weight, overweight or obese women, with emphasis on the American Institute of Medicine (IOM) recommendations. We performed secondary analyses on data based on questionnaires from 1,898 women from the "Smoke-free Newborn Study" conducted 1996-1999 at Hvidovre Hospital, Denmark. Relationship between GWG and PWR was examined according to BMI as a continuous variable and in four groups. Association between PWR and GWG according to IOM recommendations was tested by linear regression analysis and the association between PWR ≥ 5 kg (11 lbs) and GWG by logistic regression analysis. Mean GWG and mean PWR were constant for all BMI units until 26-27 kg/m(2). After this cut-off mean GWG and mean PWR decreased with increasing BMI. Nearly 40% of normal weight, 60% of overweight and 50% of obese women gained more than recommended during pregnancy. For normal weight and overweight women with GWG above recommendations the OR of gaining ≥ 5 kg (11 lbs) 1-year postpartum was 2.8 (95% CI 2.0-4.0) and 2.8 (95% CI 1.3-6.2, respectively) compared to women with GWG within recommendations. GWG above IOM recommendations significantly increases normal weight, overweight and obese women's risk of retaining weight 1 year after delivery. Health personnel face a challenge in prenatal counseling as 40-60% of these women gain more weight than recommended for their BMI. As GWG is potentially modifiable, our study should be followed by intervention studies focusing on GW.

Recent operating experiences with steam generators in Japanese NPPs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yashima, Seiji

1997-02-01

In 1994, the Genkai-3 of Kyushu Electric Power Co., Inc. and the Ikata-3 of Shikoku Electric Power Co., Inc. started commercial operation, and now 22 PWR plants are being operated in Japan. Since the first PWR plant now 22 PWR plants are being operated in was started to operate, Japanese PWR plants have had an operating experience of approx. 280 reactor-years. During that period, many tube degradations have been experienced in steam generators (SGs). And, in 1991, the steam generator tube rupture (SGTR) occurred in the Mihama-2 of Kansai Electric Power Co., Inc. However, the occurrence of tube degradation ofmore » SGs has been decreased by the instructions of the MITI as regulatory authorities, efforts of Electric Utilities, and technical support from the SG manufacturers. Here the author describes the recent SGs in Japan about the following points. (1) Recent Operating Experiences (2) Lessons learned from Mihama-2 SGTR (3) SG replacement (4) Safety Regulations on SG (5) Research and development on SG.« less

Uniaxial low cycle fatigue behavior for pre-corroded 16MND5 bainitic steel in simulated pressurized water reactor environment

NASA Astrophysics Data System (ADS)

Chen, Xu; Ren, Bin; Yu, Dunji; Xu, Bin; Zhang, Zhe; Chen, Gang

2018-06-01

The effects of uniaxial tension properties and low cycle fatigue behavior of 16MND5 bainitic steel cylinder pre-corroded in simulated pressurized water reactor (PWR) were investigated by fatigue at room temperature in air and immersion test system, scanning electron microscopy (SEM), energy disperse spectroscopy (EDS). The experimental results indicated that the corrosion fatigue lives of 16MND5 specimen were significantly affected by the strain amplitude and simulated PWR environments. The compositions of corrosion products were complexly formed in simulated PWR environments. The porous corrosion surface of pre-corroded materials tended to generate pits as a result of promoting contact area to the fresh metal, which promoted crack initiation. For original materials, the fatigue cracks initiated at inclusions imbedded in the micro-cracks. Moreover, the simulated PWR environments degraded the mechanical properties and low cycle fatigue behavior of 16MND5 specimens remarkably. Pre-corrosion of 16MND5 specimen mainly affected the plastic term of the Coffin-Manson equation.

Design study of long-life PWR using thorium cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subkhi, Moh. Nurul; Su'ud, Zaki; Waris, Abdul

2012-06-06

Design study of long-life Pressurized Water Reactor (PWR) using thorium cycle has been performed. Thorium cycle in general has higher conversion ratio in the thermal spectrum domain than uranium cycle. Cell calculation, Burn-up and multigroup diffusion calculation was performed by PIJ-CITATION-SRAC code using libraries based on JENDL 3.2. The neutronic analysis result of infinite cell calculation shows that {sup 231}Pa better than {sup 237}Np as burnable poisons in thorium fuel system. Thorium oxide system with 8%{sup 233}U enrichment and 7.6{approx} 8%{sup 231}Pa is the most suitable fuel for small-long life PWR core because it gives reactivity swing less than 1%{Delta}k/kmore » and longer burn up period (more than 20 year). By using this result, small long-life PWR core can be designed for long time operation with reduced excess reactivity as low as 0.53%{Delta}k/k and reduced power peaking during its operation.« less

Effects of Thermo-Mechanical Treatments on Deformation Behavior and IGSCC Susceptibility of Stainless Steels in Pwr Primary Water Chemistry

NASA Astrophysics Data System (ADS)

Nouraei, S.; Tice, D. R.; Mottershead, K. J.; Wright, D. M.

Field experience of 300 series stainless steels in the primary circuit of PWR plant has been good. Stress Corrosion Cracking of components has been infrequent and mainly associated with contamination by impurities/oxygen in occluded locations. However, some instances of failures have been observed which cannot necessarily be attributed to deviations in the water chemistry. These failures appear to be associated with the presence of cold-work produced by surface finishing and/or by welding-induced shrinkage. Recent data indicate that some heats of SS show an increased susceptibility to SCC; relatively high crack growth rates were observed even when the crack growth direction is orthogonal to the cold-work direction. SCC of cold-worked SS in PWR coolant is therefore determined by a complex interaction of material composition, microstructure, prior cold-work and heat treatment. This paper will focus on the interactions between these parameters on crack propagation in simulated PWR conditions.

Development of ECT/UT inspection system for bottom mounted instrumentation nozzle of PWR reactor vessels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanaka, H.; Fukui, S.; Iwahashi, Y.

1994-12-31

The development of inspection technique and tool for Bottom Mounted Instrument (BMI) nozzle of PWR plant was performed for countermeasure of leakage accident at incore instrument nozzle of Hamaoka-1 (BWR). MHI achieved the following development, of which object was PWR Plant R/V: (1) development of ECT/UT Multi-sensored Probe; (2) development of Inspection System (3) development of Data Processing System. The Inspection System had been functionally tested using full scale mock-up. As the result of the functional test, this system was confirmed to be very effective, and assumed to be hopeful for the actual application on site.

Plasmon waveguide resonance sensor using an Au-MgF2 structure.

PubMed

Zhou, Yanfei; Zhang, Pengfei; He, Yonghong; Xu, Zihao; Liu, Le; Ji, Yanhong; Ma, Hui

2014-10-01

We report an Au − MgF(2) plasmon waveguide resonance (PWR) sensor in this work. The characteristics of this sensing structure are compared with a surface plasmon resonance (SPR) structure theoretically and experimentally. The transverse-magnetic-polarized PWR sensor has a refractive index resolution of 9.3 × 10(-7) RIU, which is 6 times smaller than that of SPR at the incident light wavelength of 633 nm, and the transverse-electric-polarized PWR sensor has a refractive index resolution of 3.0 × 10(-6) RIU. This high-resolution sensor is easy to build and is less sensitive to film coating deviations.

Suggestion on the safety classification of spent fuel dry storage in China’s pressurized water reactor nuclear power plant

NASA Astrophysics Data System (ADS)

Liu, Ting; Qu, Yunhuan; Meng, De; Zhang, Qiaoer; Lu, Xinhua

2018-01-01

China’s spent fuel storage in the pressurized water reactors(PWR) is stored with wet storage way. With the rapid development of nuclear power industry, China’s NPPs(NPPs) will not be able to meet the problem of the production of spent fuel. Currently the world’s major nuclear power countries use dry storage as a way of spent fuel storage, so in recent years, China study on additional spent fuel dry storage system mainly. Part of the PWR NPP is ready to apply for additional spent fuel dry storage system. It also need to safety classificate to spent fuel dry storage facilities in PWR, but there is no standard for safety classification of spent fuel dry storage facilities in China. Because the storage facilities of the spent fuel dry storage are not part of the NPP, the classification standard of China’s NPPs is not applicable. This paper proposes the safety classification suggestion of the spent fuel dry storage for China’s PWR NPP, through to the study on China’s safety classification principles of PWR NPP in “Classification for the items of pressurized water reactor nuclear power plants (GB/T 17569-2013)”, and safety classification about spent fuel dry storage system in NUREG/CR - 6407 in the United States.

Annual report, FY 1979 Spent fuel and fuel pool component integrity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, A.B. Jr.; Bailey, W.J.; Schreiber, R.E.

International meetings under the BEFAST program and under INFCE Working Group No. 6 during 1978 and 1979 continue to indicate that no cases of fuel cladding degradation have developed on pool-stored fuel from water reactors. A section from a spent fuel rack stand, exposed for 1.5 y in the Yankee Rowe (PWR) pool had 0.001- to 0.003-in.-deep (25- to 75-..mu..m) intergranular corrosion in weld heat-affected zones but no evidence of stress corrosion cracking. A section of a 304 stainless steel spent fuel storage rack exposed 6.67 y in the Point Beach reactor (PWR) spent fuel pool showed no significant corrosion.more » A section of 304 stainless steel 8-in.-dia pipe from the Three Mile Island No. 1 (PWR) spent fuel pool heat exchanger plumbing developed a through-wall crack. The crack was intergranular, initiating from the inside surface in a weld heat-affected zone. The zone where the crack occurred was severely sensitized during field welding. The Kraftwerk Union (Erlangen, GFR) disassembled a stainless-steel fuel-handling machine that operated for 12 y in a PWR (boric acid) spent fuel pool. There was no evidence of deterioration, and the fuel-handling machine was reassembled for further use. A spent fuel pool at a Swedish PWR was decontaminated. The procedure is outlined in this report.« less

Optimization of small long-life PWR based on thorium fuel

NASA Astrophysics Data System (ADS)

Subkhi, Moh Nurul; Suud, Zaki; Waris, Abdul; Permana, Sidik

2015-09-01

A conceptual design of small long-life Pressurized Water Reactor (PWR) using thorium fuel has been investigated in neutronic aspect. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.2, while the multi-energy-group diffusion calculations were optimized in three-dimension X-Y-Z geometry of core by COREBN. The excess reactivity of thorium nitride with ZIRLO cladding is considered during 5 years of burnup without refueling. Optimization of 350 MWe long life PWR based on 5% 233U & 2.8% 231Pa, 6% 233U & 2.8% 231Pa and 7% 233U & 6% 231Pa give low excess reactivity.

78 FR 56752 - Interim Staff Guidance Specific Environmental Guidance for Integral Pressurized Water Reactors...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-13

... (iPWR). This guidance applies to environmental reviews associated with iPWR applications for limited... received on or before this date. ADDRESSES: You may submit comments by any of the following methods (unless... this document. You may access publicly-available information related to this document by any of the...

Neutron Collar Evolution and Fresh PWR Assembly Measurements with a New Fast Neutron Passive Collar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menlove, Howard Olsen; Geist, William H.; Root, Margaret A.

The passive neutron collar approach removes the effect of poison rods when using a 1mm Gd liner. This project sets out to solve the following challenges: BWR fuel assemblies have less mass and less neutron multiplication than PWR; and effective removal of cosmic ray spallation neutron bursts needed via QC tests.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.

Severe accident management can be defined as the use of existing and/or altemative resources, systems and actors to prevent or mitigate a core-melt accident. For each accident sequence and each combination of severe accident management strategies, there may be several options available to the operator, and each involves phenomenological and operational considerations regarding uncertainty. Operational uncertainties include operator, system and instrumentation behavior during an accident. A framework based on decision trees and influence diagrams has been developed which incorporates such criteria as feasibility, effectiveness, and adverse effects, for evaluating potential severe accident management strategies. The framework is also capable ofmore » propagating both data and model uncertainty. It is applied to several potential strategies including PWR cavity flooding, BWR drywell flooding, PWR depressurization and PWR feed and bleed.« less

MC21 analysis of the MIT PWR benchmark: Hot zero power results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly Iii, D. J.; Aviles, B. N.; Herman, B. R.

2013-07-01

MC21 Monte Carlo results have been compared with hot zero power measurements from an operating pressurized water reactor (PWR), as specified in a new full core PWR performance benchmark from the MIT Computational Reactor Physics Group. Included in the comparisons are axially integrated full core detector measurements, axial detector profiles, control rod bank worths, and temperature coefficients. Power depressions from grid spacers are seen clearly in the MC21 results. Application of Coarse Mesh Finite Difference (CMFD) acceleration within MC21 has been accomplished, resulting in a significant reduction of inactive batches necessary to converge the fission source. CMFD acceleration has alsomore » been shown to work seamlessly with the Uniform Fission Site (UFS) variance reduction method. (authors)« less

Secondary Startup Neutron Sources as a Source of Tritium in a Pressurized Water Reactor (PWR) Reactor Coolant System (RCS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaver, Mark W.; Lanning, Donald D.

2010-02-01

The hypothesis of this paper is that the Zircaloy clad fuel source is minimal and that secondary startup neutron sources are the significant contributors of the tritium in the RCS that was previously assigned to release from fuel. Currently there are large uncertainties in the attribution of tritium in a Pressurized Water Reactor (PWR) Reactor Coolant System (RCS). The measured amount of tritium in the coolant cannot be separated out empirically into its individual sources. Therefore, to quantify individual contributors, all sources of tritium in the RCS of a PWR must be understood theoretically and verified by the sum ofmore » the individual components equaling the measured values.« less

Optimization of small long-life PWR based on thorium fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subkhi, Moh Nurul, E-mail: nsubkhi@students.itb.ac.id; Physics Dept., Faculty of Science and Technology, State Islamic University of Sunan Gunung Djati Bandung Jalan A.H Nasution 105 Bandung; Suud, Zaki, E-mail: szaki@fi.itb.ac.id

2015-09-30

A conceptual design of small long-life Pressurized Water Reactor (PWR) using thorium fuel has been investigated in neutronic aspect. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.2, while the multi-energy-group diffusion calculations were optimized in three-dimension X-Y-Z geometry of core by COREBN. The excess reactivity of thorium nitride with ZIRLO cladding is considered during 5 years of burnup without refueling. Optimization of 350 MWe long life PWR based on 5% {sup 233}U & 2.8% {sup 231}Pa, 6% {sup 233}U & 2.8% {sup 231}Pa and 7% {sup 233}U & 6% {supmore » 231}Pa give low excess reactivity.« less

Development a computer codes to couple PWR-GALE output and PC-CREAM input

NASA Astrophysics Data System (ADS)

Kuntjoro, S.; Budi Setiawan, M.; Nursinta Adi, W.; Deswandri; Sunaryo, G. R.

2018-02-01

Radionuclide dispersion analysis is part of an important reactor safety analysis. From the analysis it can be obtained the amount of doses received by radiation workers and communities around nuclear reactor. The radionuclide dispersion analysis under normal operating conditions is carried out using the PC-CREAM code, and it requires input data such as source term and population distribution. Input data is derived from the output of another program that is PWR-GALE and written Population Distribution data in certain format. Compiling inputs for PC-CREAM programs manually requires high accuracy, as it involves large amounts of data in certain formats and often errors in compiling inputs manually. To minimize errors in input generation, than it is make coupling program for PWR-GALE and PC-CREAM programs and a program for writing population distribution according to the PC-CREAM input format. This work was conducted to create the coupling programming between PWR-GALE output and PC-CREAM input and programming to written population data in the required formats. Programming is done by using Python programming language which has advantages of multiplatform, object-oriented and interactive. The result of this work is software for coupling data of source term and written population distribution data. So that input to PC-CREAM program can be done easily and avoid formatting errors. Programming sourceterm coupling program PWR-GALE and PC-CREAM is completed, so that the creation of PC-CREAM inputs in souceterm and distribution data can be done easily and according to the desired format.

Shuttle Engine Designs Revolutionize Solar Power

NASA Technical Reports Server (NTRS)

2014-01-01

The Space Shuttle Main Engine was built under contract to Marshall Space Flight Center by Rocketdyne, now part of Pratt & Whitney Rocketdyne (PWR). PWR applied its NASA experience to solar power technology and licensed the technology to Santa Monica, California-based SolarReserve. The company now develops concentrating solar power projects, including a plant in Nevada that has created 4,300 jobs during construction.

Fourier Transform-Plasmon Waveguide Spectroscopy: A Nondestructive Multifrequency Method for Simultaneously Determining Polymer Thickness and Apparent Index of Refraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bobbitt, Jonathan M; Weibel, Stephen C; Elshobaki, Moneim

2014-12-16

Fourier transform (FT)-plasmon waveguide resonance (PWR) spectroscopy measures light reflectivity at a waveguide interface as the incident frequency and angle are scanned. Under conditions of total internal reflection, the reflected light intensity is attenuated when the incident frequency and angle satisfy conditions for exciting surface plasmon modes in the metal as well as guided modes within the waveguide. Expanding upon the concept of two-frequency surface plasmon resonance developed by Peterlinz and Georgiadis [ Opt. Commun. 1996, 130, 260], the apparent index of refraction and the thickness of a waveguide can be measured precisely and simultaneously by FT-PWR with an averagemore » percent relative error of 0.4%. Measuring reflectivity for a range of frequencies extends the analysis to a wide variety of sample compositions and thicknesses since frequencies with the maximum attenuation can be selected to optimize the analysis. Additionally, the ability to measure reflectivity curves with both p- and s-polarized light provides anisotropic indices of refraction. FT-PWR is demonstrated using polystyrene waveguides of varying thickness, and the validity of FT-PWR measurements are verified by comparing the results to data from profilometry and atomic force microscopy (AFM).« less

Fourier transform-plasmon waveguide spectroscopy: a nondestructive multifrequency method for simultaneously determining polymer thickness and apparent index of refraction.

PubMed

Bobbitt, Jonathan M; Weibel, Stephen C; Elshobaki, Moneim; Chaudhary, Sumit; Smith, Emily A

2014-12-16

Fourier transform (FT)-plasmon waveguide resonance (PWR) spectroscopy measures light reflectivity at a waveguide interface as the incident frequency and angle are scanned. Under conditions of total internal reflection, the reflected light intensity is attenuated when the incident frequency and angle satisfy conditions for exciting surface plasmon modes in the metal as well as guided modes within the waveguide. Expanding upon the concept of two-frequency surface plasmon resonance developed by Peterlinz and Georgiadis [Opt. Commun. 1996, 130, 260], the apparent index of refraction and the thickness of a waveguide can be measured precisely and simultaneously by FT-PWR with an average percent relative error of 0.4%. Measuring reflectivity for a range of frequencies extends the analysis to a wide variety of sample compositions and thicknesses since frequencies with the maximum attenuation can be selected to optimize the analysis. Additionally, the ability to measure reflectivity curves with both p- and s-polarized light provides anisotropic indices of refraction. FT-PWR is demonstrated using polystyrene waveguides of varying thickness, and the validity of FT-PWR measurements are verified by comparing the results to data from profilometry and atomic force microscopy (AFM).

Cyclic and SCC Behavior of Alloy 690 HAZ in a PWR Environment

NASA Astrophysics Data System (ADS)

Alexandreanu, Bogdan; Chen, Yiren; Natesan, Ken; Shack, Bill

The objective of this work is to determine the cyclic and stress corrosion cracking (SCC) crack growth rates (CGRs) in a simulated PWR water environment for Alloy 690 heat affected zone (HAZ). In order to meet the objective, an Alloy 152 J-weld was produced on a piece of Alloy 690 tubing, and the test specimens were aligned with the HAZ. The environmental enhancement of cyclic CGRs for Alloy 690 HAZ was comparable to that measured for the same alloy in the as-received condition. The two Alloy 690 HAZ samples tested exhibited maximum SCC CGR rates of 10-11 m/s in the simulated PWR environment at 320°C, however, on average, these rates are similar or only slightly higher than those for the as-received alloy.

Physics of hydride fueled PWR

NASA Astrophysics Data System (ADS)

Ganda, Francesco

The first part of the work presents the neutronic results of a detailed and comprehensive study of the feasibility of using hydride fuel in pressurized water reactors (PWR). The primary hydride fuel examined is U-ZrH1.6 having 45w/o uranium: two acceptable design approaches were identified: (1) use of erbium as a burnable poison; (2) replacement of a fraction of the ZrH1.6 by thorium hydride along with addition of some IFBA. The replacement of 25 v/o of ZrH 1.6 by ThH2 along with use of IFBA was identified as the preferred design approach as it gives a slight cycle length gain whereas use of erbium burnable poison results in a cycle length penalty. The feasibility of a single recycling plutonium in PWR in the form of U-PuH2-ZrH1.6 has also been assessed. This fuel was found superior to MOX in terms of the TRU fractional transmutation---53% for U-PuH2-ZrH1.6 versus 29% for MOX---and proliferation resistance. A thorough investigation of physics characteristics of hydride fuels has been performed to understand the reasons of the trends in the reactivity coefficients. The second part of this work assessed the feasibility of multi-recycling plutonium in PWR using hydride fuel. It was found that the fertile-free hydride fuel PuH2-ZrH1.6, enables multi-recycling of Pu in PWR an unlimited number of times. This unique feature of hydride fuels is due to the incorporation of a significant fraction of the hydrogen moderator in the fuel, thereby mitigating the effect of spectrum hardening due to coolant voiding accidents. An equivalent oxide fuel PuO2-ZrO2 was investigated as well and found to enable up to 10 recycles. The feasibility of recycling Pu and all the TRU using hydride fuels were investigated as well. It was found that hydride fuels allow recycling of Pu+Np at least 6 times. If it was desired to recycle all the TRU in PWR using hydrides, the number of possible recycles is limited to 3; the limit is imposed by positive large void reactivity feedback.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barry, Kenneth

The Nuclear Energy Institute (NEI) Small Modular Reactor (SMR) Licensing Task Force (TF) has been evaluating licensing issues unique and important to iPWRs, ranking these issues, and developing NEI position papers for submittal to the U.S. Nuclear Regulatory Commission (NRC) during the past three years. Papers have been developed and submitted to the NRC in a range of areas including: Price-Anderson Act, NRC annual fees, security, modularity, and staffing. In December, 2012, NEI completed a draft position paper on SMR source terms and participated in an NRC public meeting presenting a summary of this paper, which was subsequently submitted tomore » the NRC. One important conclusion of the source term paper was the evaluation and selection of high importance areas where additional research would have a significant impact on source terms. The highest ranked research area was iPWR containment aerosol natural deposition. The NRC accepts the use of existing aerosol deposition correlations in Regulatory Guide 1.183, but these were developed for large light water reactor (LWR) containments. Application of these correlations to an iPWR design has resulted in greater than a ten-fold reduction of containment airborne aerosol inventory as compared to large LWRs. Development and experimental justification of containment aerosol natural deposition correlations specifically for the unique iPWR containments is expected to result in a large reduction of design basis and beyond-design-basis accident source terms with concomitantly smaller dose to workers and the public. Therefore, NRC acceptance of iPWR containment aerosol natural deposition correlations will directly support the industry’s goal of reducing the Emergency Planning Zone (EPZ) for SMRs. Based on the results in this work, it is clear that thermophoresis is relatively unimportant for iPWRs. Gravitational settling is well understood, and may be the dominant process for a dry environment. Diffusiophoresis and enhanced settling by particle growth are the dominant processes for determining DFs for expected conditions in an iPWR containment. These processes are dependent on the areato-volume (A/V) ratio, which should benefit iPWR designs because these reactors have higher A/Vs compared to existing LWRs.« less

Report on the PWR-radiation protection/ALARA Committee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malone, D.J.

1995-03-01

In 1992, representatives from several utilities with operational Pressurized Water Reactors (PWR) formed the PWR-Radiation Protection/ALARA Committee. The mission of the Committee is to facilitate open communications between member utilities relative to radiation protection and ALARA issues such that cost effective dose reduction and radiation protection measures may be instituted. While industry deregulation appears inevitable and inter-utility competition is on the rise, Committee members are fully committed to sharing both positive and negative experiences for the benefit of the health and safety of the radiation worker. Committee meetings provide current operational experiences through members providing Plant status reports, and informationmore » relative to programmatic improvements through member presentations and topic specific workshops. The most recent Committee workshop was facilitated to provide members with defined experiences that provide cost effective ALARA performance.« less

Primary water chemistry improvement for radiation exposure reduction at Japanese PWR Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nishizawa, Eiichi

1995-03-01

Radiation exposure during the refueling outages at Japanese Pressurized Water Reactor (PWR) Plants has been gradually decreased through continuous efforts keeping the radiation dose rates at relatively low level. The improvement of primary water chemistry in respect to reduction of the radiation sources appears as one of the most important contributions to the achieved results and can be classified by the plant operation conditions as follows

Comparison of Measures of Vibration Affecting Occupants of Military Vehicles

DTIC Science & Technology

1986-12-01

8217 ,, l I WES equipment 27. The WES equipment consisted of a battery operated absorbed power ( ABS -PW) meter with signal conditioning...West Germany. These will be referred to as the ISO ride meter and the ABS -PWR ridemeter, respectively. The first implemented the vibration measure...the ABS -PWR algorithms were used with each acceleration signal source (analog and digital) to provide a comprehensive basis for comparing the vibration

Fatigue crack growth rates in a pressure vessel steel under various conditions of loading and the environment

NASA Astrophysics Data System (ADS)

Hicks, P. D.; Robinson, F. P. A.

1986-10-01

Corrosion fatigue (CF) tests have been carried out on SA508 Cl 3 pressure vessel steel, in simulated P.W.R. environments. The test variables investigated included air and P.W.R. water environments, frequency variation over the range 1 Hz to 10 Hz, transverse and longitudinal crack growth directions, temperatures of 20 °C and 50 °C, and R-ratios of 0.2 and 0.7. It was found that decreasing the test frequency increased fatigue crack growth rates (FCGR) in P.W.R. environments, P.W.R. environment testing gave enhanced crack growth (vs air tests), FCGRs were greater for cracks growing in the longitudinal direction, slight increases in temperature gave noticeable accelerations in FCGR, and several air tests gave FCGR greater than those predicted by the existing ASME codes. Fractographic evidence indicates that FCGRs were accelerated by a hydrogen embrittlement mechanism. The presence of elongated MnS inclusions aided both mechanical fatigue and hydrogen embrittlement processes, thus producing synergistically fast FCGRs. Both anodic dissolution and hydrogen embrittlement mechanisms have been proposed for the environmental enhancement of crack growth rates. Electrochemical potential measurements and potentiostatic tests have shown that sample isolation of the test specimens from the clevises in the apparatus is not essential during low temperature corrosion fatigue testing.

SAS2H Generated Isotopic Concentrations For B&W 15X15 PWR Assembly (SCPB:N/A)

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.W. Davis

This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) to provide pressurized water reactor (PWR) isotopic composition data as a function of time for use in criticality analyses. The objectives of this evaluation are to generate burnup and decay dependant isotopic inventories and to provide these inventories in a form which can easily be utilized in subsequent criticality calculations.

Astronaut Robinson presents 2010 Silver Snoopy awards

NASA Image and Video Library

2010-06-23

NASA's John C. Stennis Space Center Director Patrick Scheuermann and astronaut Steve Robinson stand with recipients of the 2010 Silver Snoopy awards following a June 23 ceremony. Sixteen Stennis employees received the astronauts' personal award, which is presented by a member of the astronaut corps representing its core principles for outstanding flight safety and mission success. This year's recipients and ceremony participants were: (front row, l to r): Cliff Arnold (NASA), Wendy Holladay (NASA), Kendra Moran (Pratt & Whitney Rocketdyne), Mary Johnson (Jacobs Technology Facility Operating Services Contract group), Cory Beckemeyer (PWR), Dean Bourlet (PWR), Cecile Saltzman (NASA), Marla Carpenter (Jacobs FOSC), David Alston (Jacobs FOSC); (back row, l to r) Scheuermann, Don Wilson (A2 Research), Tim White (NASA), Ira Lossett (Jacobs Technology NASA Test Operations Group), Kerry Gallagher (Jacobs NTOG); Rene LeFrere (PWR), Todd Ladner (ASRC Research and Technology Solutions) and Thomas Jacks (NASA).

Design, Construction and Testing of an In-Pile Loop for PWR (Pressurized Water Reactor) Simulation.

DTIC Science & Technology

1987-06-01

computer modeling remains at best semiempirical (C-i), this large variation in scaling factor makes extrapolation of data impossible. The DIDO Water...in a full scale PWR are not practical. The reactor plant is not controlled to tolerances necessary for research, and utilities are reluctant to vary...MIT Reactor Safeguards Committee, in revision 1 to the PCCL Safety Evaluation Report (SER), for final approval to begin in-pile testing and

MELCOR model for an experimental 17x17 spent fuel PWR assembly.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cardoni, Jeffrey

2010-11-01

A MELCOR model has been developed to simulate a pressurized water reactor (PWR) 17 x 17 assembly in a spent fuel pool rack cell undergoing severe accident conditions. To the extent possible, the MELCOR model reflects the actual geometry, materials, and masses present in the experimental arrangement for the Sandia Fuel Project (SFP). The report presents an overview of the SFP experimental arrangement, the MELCOR model specifications, demonstration calculation results, and the input model listing.

Surrogate fuel assembly multi-axis shaker tests to simulate normal conditions of rail and truck transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

McConnell, Paul E.; Koenig, Greg John; Uncapher, William Leonard

2016-05-01

This report describes the third set of tests (the “DCLa shaker tests”) of an instrumented surrogate PWR fuel assembly. The purpose of this set of tests was to measure strains and accelerations on Zircaloy-4 fuel rods when the PWR assembly was subjected to rail and truck loadings simulating normal conditions of transport when affixed to a multi-axis shaker. This is the first set of tests of the assembly simulating rail normal conditions of transport.

Surrogate fuel assembly multi-axis shaker tests to simulate normal conditions of rail and truck transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

McConnell, Paul E.; Koenig, Greg John; Uncapher, William Leonard

2016-05-12

This report describes the third set of tests (the “DCL a shaker tests”) of an instrumented surrogate PWR fuel assembly. The purpose of this set of tests was to measure strains and accelerations on Zircaloy-4 fuel rods when the PWR assembly was subjected to rail and truck loadings simulating normal conditions of transport when affixed to a multi-axis shaker. This is the first set of tests of the assembly simulating rail normal conditions of transport.

Effects of crack tip plastic zone on corrosion fatigue cracking of alloy 690(TT) in pressurized water reactor environments

NASA Astrophysics Data System (ADS)

Xiao, J.; Qiu, S. Y.; Chen, Y.; Fu, Z. H.; Lin, Z. X.; Xu, Q.

2015-01-01

Alloy 690(TT) is widely used for steam generator tubes in pressurized water reactor (PWR), where it is susceptible to corrosion fatigue. In this study, the corrosion fatigue behavior of Alloy 690(TT) in simulated PWR environments was investigated. The microstructure of the plastic zone near the crack tip was investigated and labyrinth structures were observed. The relationship between the crack tip plastic zone and fatigue crack growth rates and the environment factor Fen was illuminated.

Waterside corrosion of Zircaloy-clad fuel rods in a PWR environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garzarolli, F.; Jorde, D.; Manzel, R.

A data base of Zircaloy corrosion behavior under PWR operating conditions has been established from previously published reports as well as from new Kraftwerk Union (KWU) fuel examinations. The data show that the reactor environment increases the corrosion. ZrO/sub 2/ film thermal conductivity is another major factor that influences corrosion behavior. It was inferred from KWU film thickness data that the oxide film thermal conductivity may decrease once circumferential cracks develop in the layer. 57 refs.

Chemical Agonists of the PML/Daxx Pathway for Prostate Cancer Therapy

DTIC Science & Technology

2011-04-01

positive nuclei. These data suggest that the assay is highly specific and will not suffer from promiscuous reactivity with NIH library compounds...Figure 16B). Strikingly, when we compared Daxx levels in PCa cell lines to a nontumorigenic human prostatic epithelial line, PWR -1E, they were...Lysates from six different cell types ( PWR -1E, ALVA-31 Daxx K/D, ALVA-31 WT, DU145, LNCaP, and PC3) were normalized for total protein content (60 μg

Industry Application ECCS / LOCA Integrated Cladding/Emergency Core Cooling System Performance: Demonstration of LOTUS-Baseline Coupled Analysis of the South Texas Plant Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Hongbin; Szilard, Ronaldo; Epiney, Aaron

Under the auspices of the DOE LWRS Program RISMC Industry Application ECCS/LOCA, INL has engaged staff from both South Texas Project (STP) and the Texas A&M University (TAMU) to produce a generic pressurized water reactor (PWR) model including reactor core, clad/fuel design and systems thermal hydraulics based on the South Texas Project (STP) nuclear power plant, a 4-Loop Westinghouse PWR. A RISMC toolkit, named LOCA Toolkit for the U.S. (LOTUS), has been developed for use in this generic PWR plant model to assess safety margins for the proposed NRC 10 CFR 50.46c rule, Emergency Core Cooling System (ECCS) performance duringmore » LOCA. This demonstration includes coupled analysis of core design, fuel design, thermalhydraulics and systems analysis, using advanced risk analysis tools and methods to investigate a wide range of results. Within this context, a multi-physics best estimate plus uncertainty (MPBEPU) methodology framework is proposed.« less

High-temperature Gas Reactor (HTGR)

NASA Astrophysics Data System (ADS)

Abedi, Sajad

2011-05-01

General Atomics (GA) has over 35 years experience in prismatic block High-temperature Gas Reactor (HTGR) technology design. During this period, the design has recently involved into a modular have been performed to demonstrate its versatility. This versatility is directly related to refractory TRISO coated - particle fuel that can contain any type of fuel. This paper summarized GA's fuel cycle studies individually and compares each based upon its cycle sustainability, proliferation-resistance capabilities, and other performance data against pressurized water reactor (PWR) fuel cycle data. Fuel cycle studies LEU-NV;commercial HEU-Th;commercial LEU-Th;weapons-grade plutonium consumption; and burning of LWR waste including plutonium and minor actinides in the MHR. results show that all commercial MHR options, with the exception of HEU-TH, are more sustainable than a PWR fuel cycle. With LEU-NV being the most sustainable commercial options. In addition, all commercial MHR options out perform the PWR with regards to its proliferation-resistance, with thorium fuel cycle having the best proliferation-resistance characteristics.

Review of PWR fuel rod waterside corrosion behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garzarolli, F.; Jorde, D.; Manzel, R.

Waterside corrosion of Zircaloy has generally not been a problem under normal PWR operating conditions, although some instances of accelerated corrosion have been reported. However, an incentive exists to extend the average fuel rod discharge burnups to about 50,000 MWd/MTU. To minimize corrosion at these extended burnups, the factors which influence Zircaloy corrosion need to be better understood. A data base of Zircaloy corrosion behavior under PWR operating conditions has been established. The data are compiled previously published reports as well as from new Kraftwerk Union examinations. A non-destructive eddy-current technique is used to measure the oxide layer thickness onmore » fuel rods. Comparisons of measuremnts made using this eddy-current technique with those made by usual metallographic methods indicate good agreement. The data were evaluated by defining a fitting factor F which describes the increase in corrosion rate observed in-reactor over that observed from measurements of ex-reactor corrosion coupons.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faidy, C.

Practical applications of the leak-before break concept are presently limited in French Pressurized Water Reactors (PWR) compared to Fast Breeder Reactors. Neithertheless, different fracture mechanic demonstrations have been done on different primary, auxiliary and secondary PWR piping systems based on similar requirements that the American NUREG 1061 specifications. The consequences of the success in different demonstrations are still in discussion to be included in the global safety assessment of the plants, such as the consequences on in-service inspections, leak detection systems, support optimization,.... A large research and development program, realized in different co-operative agreements, completes the general approach.

Effects of Lower Drying-Storage Temperature on the Ductility of High-Burnup PWR Cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Billone, M. C.; Burtseva, T. A.

2016-08-30

The purpose of this research effort is to determine the effects of canister and/or cask drying and storage on radial hydride precipitation in, and potential embrittlement of, high-burnup (HBU) pressurized water reactor (PWR) cladding alloys during cooling for a range of peak drying-storage temperatures (PCT) and hoop stresses. Extensive precipitation of radial hydrides could lower the failure hoop stresses and strains, relative to limits established for as-irradiated cladding from discharged fuel rods stored in pools, at temperatures below the ductile-to-brittle transition temperature (DBTT).

In-situ material-motion diagnostics and fuel radiography in experimental reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeVolpi, A.

1982-01-01

Material-motion monitoring has become a routine part of in-pile transient reactor-safety experiments. Diagnostic systems, such as the fast-neutron hodoscope, were developed for the purpose of providing direct time-resolved data on pre-failure fuel motion, cladding-breach time and location, and post-failure fuel relocation. Hodoscopes for this purpose have been installed at TREAT and CABRI; other types of imaging systems that have been tested are a coded-aperture at ACRR and a pinhole at TREAT. Diagnostic systems that use penetrating radiation emitted from the test section can non-invasively monitor fuel without damage to the measuring instrument during the radiographic images of test sections installedmore » in the reator. Studies have been made of applications of hodoscopes to other experimental reactors, including PBF, FARET, STF, ETR, EBR-II, SAREF-STF, and DMT.« less

ACHILLES: Heat Transfer in PWR Core During LOCA Reflood Phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

2013-11-01

1. NAME AND TITLE OF DATA LIBRARY ACHILLES -Heat Transfer in PWR Core During LOCA Reflood Phase. 2. NAME AND TITLE OF DATA RETRIEVAL PROGRAMS N/A 3. CONTRIBUTOR AEA Technology, Winfrith Technology Centre, Dorchester DT2 8DH United Kingdom through the OECD Nuclear Energy Agency Data Bank, Issy-les-Moulineaux, France. 4. DESCRIPTION OF TEST FACILITY The most important features of the Achilles rig were the shroud vessel, which contained the test section, and the downcomer. These may be thought of as representing the core barrel and the annular downcomer in the reactor pressure vessel. The test section comprises a cluster of 69more » rods in a square array within a circular shroud vessel. The rod diameter and pitch (9.5 mm and 12.6 mm) were typical of PWR dimensions. The internal diameter of the shroud vessel was 128 mm. Each rod was electrically heated over a length of 3.66 m, which is typical of the nuclear heated length in a PWR fuel rod, and each contained 6 internal thermocouples. These were arranged in one of 8 groupings which concentrated the thermocouples in different axial zones. The spacer grids were at prototypic PWR locations. Each grid had two thermocouples attached to its trailing edge at radial locations. The axial power profile along the rods was an 11 step approximation to a "chopped cosine". The shroud vessel had 5 heating zones whose power could be independently controlled. 5. DESCRIPTION OF TESTS The Achilles experiments investigated the heat transfer in the core of a Pressurized Water Reactor during the re-flood phase of a postulated large break loss of coolant accident. The results provided data to validate codes and to improve modeling. Different types of experiments were carried out which included single phase cooling, re-flood under low flow conditions, level swell and re-flood under high flow conditions. Three series of experiments were performed. The first and the third used the same test section but the second used another test section, similar in all respects except that it contained a partial blockage formed by attaching sleeves (or "balloons") to some of the rods. 6. SOURCE AND SCOPE OF DATA Phenomena Tested - Heat transfer in the core of a PWR during a re-flood phase of postulated large break LOCA. Test Designation - Achilles Rig. The programme includes the following types of experiments: - on an unballooned cluster: -- single phase air flow -- low pressure level swell -- low flooding rate re-flood -- high flooding rate re-flood - on a ballooned cluster containing 80% blockage formed by 16 balloon sleeves -- single phase air flow -- low flooding rate re-flood 7. DISCUSSION OF THE DATA RETRIEVAL PROGRAM N/A 8. DATA FORMAT AND COMPUTER Many Computers (M00019MNYCP00). 9. TYPICAL RUNNING TIME N/A 11. CONTENTS OF LIBRARY The ACHILLES package contains test data and associated data processing software as well as the documentation listed above. 12. DATE OF ABSTRACT November 2013. KEYWORDS: DATABASES, BENCHMARKS, HEAT TRANSFER, LOSS-OF-COLLANT ACCIDENT, PWR REACTORS, REFLOODING« less

Dissolution experiments of commercial PWR (52 MWd/kgU) and BWR (53 MWd/kgU) spent nuclear fuel cladded segments in bicarbonate water under oxidizing conditions. Experimental determination of matrix and instant release fraction

NASA Astrophysics Data System (ADS)

González-Robles, E.; Serrano-Purroy, D.; Sureda, R.; Casas, I.; de Pablo, J.

2015-10-01

The denominated instant release fraction (IRF) is considered in performance assessment (PA) exercises to govern the dose that could arise from the repository. A conservative definition of IRF comprises the total inventory of radionuclides located in the gap, fractures, and the grain boundaries and, if present, in the high burn-up structure (HBS). The values calculated from this theoretical approach correspond to an upper limit that likely does not correspond to what it will be expected to be instantaneously released in the real system. Trying to ascertain this IRF from an experimental point of view, static leaching experiments have been carried out with two commercial UO2 spent nuclear fuels (SNF): one from a pressurized water reactor (PWR), labelled PWR, with an average burn-up (BU) of 52 MWd/kgU and fission gas release (FGR) of 23.1%, and one from a boiling water reactor (BWR), labelled BWR, with an average BU of and 53 MWd/kgU and FGR of 3.9%. One sample of each SNF, consisting of fuel and cladding, has been leached in bicarbonate water during one year under oxidizing conditions at room temperature (25 ± 5)°C. The behaviour of the concentration measured in solution can be divided in two according to the release rate. All radionuclides presented an initial release rate that after some days levels down to a slower second one, which remains constant until the end of the experiment. Cumulative fraction of inventory in aqueous phase (FIAPc) values has been calculated. Results show faster release in the case of the PWR SNF. In both cases Np, Pu, Am, Cm, Y, Tc, La and Nd dissolve congruently with U, while dissolution of Zr, Ru and Rh is slower. Rb, Sr, Cs and Mo, dissolve faster than U. The IRF of Cs at 10 and 200 days has been calculated, being (3.10 ± 0.62) and (3.66 ± 0.73) for PWR fuel, and (0.35 ± 0.07) and (0.51 ± 0.10) for BWR fuel.

Preliminary Stratigraphic Basis for Geologic Mapping of Venus

NASA Technical Reports Server (NTRS)

Basilevsky, A. T.; Head, J. W.

1993-01-01

The age relations between geologic formations have been studied at 36 1000x1000 km areas centered at the dark paraboloid craters. The geologic setting in all these sites could be characterized using only 16 types of features and terrains (units). These units form a basic stratigraphic sequence (from older to younger: (1) Tessera (Tt); (2-3) Densely fractured terrains associated with coronae (COdf) and in the form of remnants among plains (Pdf); (4) Fractured and ridged plains (Pfr); (5) Plains with wrinkle ridges (Pwr); (6-7) Smooth and lobate plains (Ps/Pl); and (8) Rift-associated fractures (Fra). The stratigraphic position of the other units is determined by their relation with the units of the basic sequence: (9) Ridge bells (RB), contemporary with Pfr; (10-11) Ridges of coronae and arachnoids annuli (COar/Aar), contemporary with wrinkle ridges of Pwr; (12) Fractures of coronae annuli (COaf) disrupt Pwr and Ps/Pl; (13) Fractures (F) disrupt Pwr or younger units; (14) Craters with associated dark paraboloids (Cdp), which are on top of all volcanic and tectonic units except the youngest episodes of rift-associated fracturing and volcanism; (15-16) Surficial streaks (Ss) and surficial patches (Sp) are approximately contemporary with Cdp. These units may be used as a tentative basis for the geologic mapping of Venus including VMAP. This mapping should test the stratigraphy and answer the question of whether this stratigraphic sequence corresponds to geologic events which were generally synchronous all around the planet or whether the sequence is simply a typical sequence of events which occurred in different places at diffferent times.

Multi-pack Disposal Concepts for Spent Fuel (Rev. 0)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadgu, Teklu; Hardin, Ernest; Matteo, Edward N.

2015-12-01

At the initiation of the Used Fuel Disposition (UFD) R&D campaign, international geologic disposal programs and past work in the U.S. were surveyed to identify viable disposal concepts for crystalline, clay/shale, and salt host media (Hardin et al., 2012). Concepts for disposal of commercial spent nuclear fuel (SNF) and high-level waste (HLW) from reprocessing are relatively advanced in countries such as Finland, France, and Sweden. The UFD work quickly showed that these international concepts are all “enclosed,” whereby waste packages are emplaced in direct or close contact with natural or engineered materials . Alternative “open” modes (emplacement tunnels are keptmore » open after emplacement for extended ventilation) have been limited to the Yucca Mountain License Application Design (CRWMS M&O, 1999). Thermal analysis showed that, if “enclosed” concepts are constrained by peak package/buffer temperature, waste package capacity is limited to 4 PWR assemblies (or 9-BWR) in all media except salt. This information motivated separate studies: 1) extend the peak temperature tolerance of backfill materials, which is ongoing; and 2) develop small canisters (up to 4-PWR size) that can be grouped in larger multi-pack units for convenience of storage, transportation, and possibly disposal (should the disposal concept permit larger packages). A recent result from the second line of investigation is the Task Order 18 report: Generic Design for Small Standardized Transportation, Aging and Disposal Canister Systems (EnergySolution, 2015). This report identifies disposal concepts for the small canisters (4-PWR size) drawing heavily on previous work, and for the multi-pack (16-PWR or 36-BWR).« less

Multi-Pack Disposal Concepts for Spent Fuel (Revision 1)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hardin, Ernest; Matteo, Edward N.; Hadgu, Teklu

2016-01-01

At the initiation of the Used Fuel Disposition (UFD) R&D campaign, international geologic disposal programs and past work in the U.S. were surveyed to identify viable disposal concepts for crystalline, clay/shale, and salt host media. Concepts for disposal of commercial spent nuclear fuel (SNF) and high-level waste (HLW) from reprocessing are relatively advanced in countries such as Finland, France, and Sweden. The UFD work quickly showed that these international concepts are all “enclosed,” whereby waste packages are emplaced in direct or close contact with natural or engineered materials . Alternative “open” modes (emplacement tunnels are kept open after emplacement formore » extended ventilation) have been limited to the Yucca Mountain License Application Design. Thermal analysis showed that if “enclosed” concepts are constrained by peak package/buffer temperature, that waste package capacity is limited to 4 PWR assemblies (or 9 BWR) in all media except salt. This information motivated separate studies: 1) extend the peak temperature tolerance of backfill materials, which is ongoing; and 2) develop small canisters (up to 4-PWR size) that can be grouped in larger multi-pack units for convenience of storage, transportation, and possibly disposal (should the disposal concept permit larger packages). A recent result from the second line of investigation is the Task Order 18 report: Generic Design for Small Standardized Transportation, Aging and Disposal Canister Systems. This report identifies disposal concepts for the small canisters (4-PWR size) drawing heavily on previous work, and for the multi-pack (16-PWR or 36-BWR).« less

Coexistence of insulin resistance and increased glucose tolerance in pregnant rats: a physiological mechanism for glucose maintenance.

PubMed

Carrara, Marcia Aparecida; Batista, Márcia Regina; Saruhashi, Tiago Ribeiro; Felisberto, Antonio Machado; Guilhermetti, Marcio; Bazotte, Roberto Barbosa

2012-06-06

The contribution of insulin resistance (IR) and glucose tolerance to the maintenance of blood glucose levels in non diabetic pregnant Wistar rats (PWR) was investigated. PWR were submitted to conventional insulin tolerance test (ITT) and glucose tolerance test (GTT) using blood sample collected 0, 10 and 60 min after intraperitoneal insulin (1 U/kg) or oral (gavage) glucose (1g/kg) administration. Moreover, ITT, GTT and the kinetics of glucose concentration changes in the fed and fasted states were evaluated with a real-time continuous glucose monitoring system (RT-CGMS) technique. Furthermore, the contribution of the liver glucose production was investigated. Conventional ITT and GTT at 0, 7, 14 and 20 days of pregnancy revealed increased IR and glucose tolerance after 20 days of pregnancy. Thus, this period of pregnancy was used to investigate the kinetics of glucose changes with the RT-CGMS technique. PWR (day 20) exhibited a lower (p<0.05) glucose concentration in the fed state. In addition, we observed IR and increased glucose tolerance in the fed state (PWR-day 20 vs. day 0). Furthermore, our data from glycogenolysis and gluconeogenesis suggested that the liver glucose production did not contribute to these changes in insulin sensitivity and/or glucose tolerance during late pregnancy. In contrast to the general view that IR is a pathological process associated with gestational diabetes, a certain degree of IR may represent an important physiological mechanism for blood glucose maintenance during fasting. Copyright © 2012 Elsevier Inc. All rights reserved.

The pluralistic water research concept - a new human-water system research approach

NASA Astrophysics Data System (ADS)

Evers, Mariele; Höllermann, Britta; Almoradie, Adrian; Taft, Linda; Garcia-Santos, Glenda

2017-04-01

Sustainable water resources management has been and still is a main challenge for decision makers even though for the past number of decades integrative approaches and concepts (e.g. Integrated Water Resources Management - IWRM) have been developed to address problems on floods, droughts, water quality, water quantity, environment and ecology. Although somehow these approaches are aiming to address water related problems in an integrative approach and to some extent include or involve society in the planning and management, they still lack some of the vital components in including the social dimensions and their interaction with water. Understanding these dynamics in a holistic way and how they are shaped by time and space may tackle these shortcomings and provide more effective and sustainable management solutions with respect to a set of potential present social actions and values as well as possible futures. This paper aims to discuss challenges to coherently and comprehensively integrate the social dimensions of different human-water concepts like IWRM, socio-hydrology and waterscape. Against this background it will develop criteria for an integrative approach and present a newly developed concept termed pluralistic water research (PWR) concept. PWR is not only a pluralistic but also an integrative and interdisciplinary approach to acknowledge the social and water dimensions and their interaction and dynamics by considering more than one perspective of a water-related issue, hereby providing a set of multiple (future) developments. Our PWR concept will be illustrated by a case study application of the Canary island La Gomera. Furthermore an outlook on further possible developments of the PWR concept will be presented and discussed.

Tensile and Fatigue Testing and Material Hardening Model Development for 508 LAS Base Metal and 316 SS Similar Metal Weld under In-air and PWR Primary Loop Water Conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohanty, Subhasish; Soppet, William; Majumdar, Saurin

This report provides an update on an assessment of environmentally assisted fatigue for light water reactor components under extended service conditions. This report is a deliverable in September 2015 under the work package for environmentally assisted fatigue under DOE’s Light Water Reactor Sustainability program. In an April 2015 report we presented a baseline mechanistic finite element model of a two-loop pressurized water reactor (PWR) for systemlevel heat transfer analysis and subsequent thermal-mechanical stress analysis and fatigue life estimation under reactor thermal-mechanical cycles. In the present report, we provide tensile and fatigue test data for 508 low-alloy steel (LAS) base metal,more » 508 LAS heat-affected zone metal in 508 LAS–316 stainless steel (SS) dissimilar metal welds, and 316 SS-316 SS similar metal welds. The test was conducted under different conditions such as in air at room temperature, in air at 300 oC, and under PWR primary loop water conditions. Data are provided on materials properties related to time-independent tensile tests and time-dependent cyclic tests, such as elastic modulus, elastic and offset strain yield limit stress, and linear and nonlinear kinematic hardening model parameters. The overall objective of this report is to provide guidance to estimate tensile/fatigue hardening parameters from test data. Also, the material models and parameters reported here can directly be used in commercially available finite element codes for fatigue and ratcheting evaluation of reactor components under in-air and PWR water conditions.« less

Fabrication of simulated DUPIC fuel

NASA Astrophysics Data System (ADS)

Kang, Kweon Ho; Song, Ki Chan; Park, Hee Sung; Moon, Je Sun; Yang, Myung Seung

2000-12-01

Simulated DUPIC fuel provides a convenient way to investigate the DUPIC fuel properties and behavior such as thermal conductivity, thermal expansion, fission gas release, leaching, and so on without the complications of handling radioactive materials. Several pellets simulating the composition and microstructure of DUPIC fuel are fabricated by resintering the powder, which was treated through OREOX process of simulated spent PWR fuel pellets, which had been prepared from a mixture of UO2 and stable forms of constituent nuclides. The key issues for producing simulated pellets that replicate the phases and microstructure of irradiated fuel are to achieve a submicrometre dispersion during mixing and diffusional homogeneity during sintering. This study describes the powder treatment, OREOX, compaction and sintering to fabricate simulated DUPIC fuel using the simulated spent PWR fuel. The homogeneity of additives in the powder was observed after attrition milling. The microstructure of the simulated spent PWR fuel agrees well with the other studies. The leading structural features observed are as follows: rare earth and other oxides dissolved in the UO2 matrix, small metallic precipitates distributed throughout the matrix, and a perovskite phase finely dispersed on grain boundaries.

Development of a new lattice physics code robin for PWR application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, S.; Chen, G.

2013-07-01

This paper presents a description of methodologies and preliminary verification results of a new lattice physics code ROBIN, being developed for PWR application at Shanghai NuStar Nuclear Power Technology Co., Ltd. The methods used in ROBIN to fulfill various tasks of lattice physics analysis are an integration of historical methods and new methods that came into being very recently. Not only these methods like equivalence theory for resonance treatment and method of characteristics for neutron transport calculation are adopted, as they are applied in many of today's production-level LWR lattice codes, but also very useful new methods like the enhancedmore » neutron current method for Dancoff correction in large and complicated geometry and the log linear rate constant power depletion method for Gd-bearing fuel are implemented in the code. A small sample of verification results are provided to illustrate the type of accuracy achievable using ROBIN. It is demonstrated that ROBIN is capable of satisfying most of the needs for PWR lattice analysis and has the potential to become a production quality code in the future. (authors)« less

Logistics Modeling of Emplacement Rate and Duration of Operations for Generic Geologic Repository Concepts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalinina, Elena Arkadievna; Hardin, Ernest

This study identified potential geologic repository concepts for disposal of spent nuclear fuel (SNF) and (2) evaluated the achievable repository waste emplacement rate and the time required to complete the disposal for these concepts. Total repository capacity is assumed to be approximately 140,000 MT of spent fuel. The results of this study provide an important input for the rough-order-of-magnitude (ROM) disposal cost analysis. The disposal concepts cover three major categories of host geologic media: crystalline or hard rock, salt, and argillaceous rock. Four waste package sizes are considered: 4PWR/9BWR; 12PWR/21BWR; 21PWR/44BWR, and dual purpose canisters (DPCs). The DPC concepts assumemore » that the existing canisters will be sealed into disposal overpacks for direct disposal. Each concept assumes one of the following emplacement power limits for either emplacement or repository closure: 1.7 kW; 2.2 kW; 5.5 kW; 10 kW; 11.5 kW, and 18 kW.« less

Regeneratively Cooled Liquid Oxygen/Methane Technology Development Between NASA MSFC and PWR

NASA Technical Reports Server (NTRS)

Robinson, Joel W.; Greene, Christopher B.; Stout, Jeffrey B.

2012-01-01

The National Aeronautics & Space Administration (NASA) has identified Liquid Oxygen (LOX)/Liquid Methane (LCH4) as a potential propellant combination for future space vehicles based upon exploration studies. The technology is estimated to have higher performance and lower overall systems mass compared to existing hypergolic propulsion systems. NASA-Marshall Space Flight Center (MSFC) in concert with industry partner Pratt & Whitney Rocketdyne (PWR) utilized a Space Act Agreement to test an oxygen/methane engine system in the Summer of 2010. PWR provided a 5,500 lbf (24,465 N) LOX/LCH4 regenerative cycle engine to demonstrate advanced thrust chamber assembly hardware and to evaluate the performance characteristics of the system. The chamber designs offered alternatives to traditional regenerative engine designs with improvements in cost and/or performance. MSFC provided the test stand, consumables and test personnel. The hot fire testing explored the effective cooling of one of the thrust chamber designs along with determining the combustion efficiency with variations of pressure and mixture ratio. The paper will summarize the status of these efforts.

VERA Core Simulator Methodology for PWR Cycle Depletion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kochunas, Brendan; Collins, Benjamin S; Jabaay, Daniel

2015-01-01

This paper describes the methodology developed and implemented in MPACT for performing high-fidelity pressurized water reactor (PWR) multi-cycle core physics calculations. MPACT is being developed primarily for application within the Consortium for the Advanced Simulation of Light Water Reactors (CASL) as one of the main components of the VERA Core Simulator, the others being COBRA-TF and ORIGEN. The methods summarized in this paper include a methodology for performing resonance self-shielding and computing macroscopic cross sections, 2-D/1-D transport, nuclide depletion, thermal-hydraulic feedback, and other supporting methods. These methods represent a minimal set needed to simulate high-fidelity models of a realistic nuclearmore » reactor. Results demonstrating this are presented from the simulation of a realistic model of the first cycle of Watts Bar Unit 1. The simulation, which approximates the cycle operation, is observed to be within 50 ppm boron (ppmB) reactivity for all simulated points in the cycle and approximately 15 ppmB for a consistent statepoint. The verification and validation of the PWR cycle depletion capability in MPACT is the focus of two companion papers.« less

Irradiation performance of (Th,Pu)O2 fuel under Pressurized Water Reactor conditions

NASA Astrophysics Data System (ADS)

Boer, B.; Lemehov, S.; Wéber, M.; Parthoens, Y.; Gysemans, M.; McGinley, J.; Somers, J.; Verwerft, M.

2016-04-01

This paper examines the in-pile safety performance of (Th,Pu)O2 fuel pins under simulated Pressurized Water Reactor (PWR) conditions. Both sol-gel and SOLMAS produced (Th,Pu)O2 fuels at enrichments of 7.9% and 12.8% in Pu/HM have been irradiated at SCK·CEN. The irradiation has been performed under PWR conditions (155 bar, 300 °C) in a dedicated loop of the BR-2 reactor. The loop is instrumented with flow and temperature monitors at inlet and outlet, which allow for an accurate measurement of the deposited enthalpy.

PWR Facility Dose Modeling Using MCNP5 and the CADIS/ADVANTG Variance-Reduction Methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blakeman, Edward D; Peplow, Douglas E.; Wagner, John C

2007-09-01

The feasibility of modeling a pressurized-water-reactor (PWR) facility and calculating dose rates at all locations within the containment and adjoining structures using MCNP5 with mesh tallies is presented. Calculations of dose rates resulting from neutron and photon sources from the reactor (operating and shut down for various periods) and the spent fuel pool, as well as for the photon source from the primary coolant loop, were all of interest. Identification of the PWR facility, development of the MCNP-based model and automation of the run process, calculation of the various sources, and development of methods for visually examining mesh tally filesmore » and extracting dose rates were all a significant part of the project. Advanced variance reduction, which was required because of the size of the model and the large amount of shielding, was performed via the CADIS/ADVANTG approach. This methodology uses an automatically generated three-dimensional discrete ordinates model to calculate adjoint fluxes from which MCNP weight windows and source bias parameters are generated. Investigative calculations were performed using a simple block model and a simplified full-scale model of the PWR containment, in which the adjoint source was placed in various regions. In general, it was shown that placement of the adjoint source on the periphery of the model provided adequate results for regions reasonably close to the source (e.g., within the containment structure for the reactor source). A modification to the CADIS/ADVANTG methodology was also studied in which a global adjoint source is weighted by the reciprocal of the dose response calculated by an earlier forward discrete ordinates calculation. This method showed improved results over those using the standard CADIS/ADVANTG approach, and its further investigation is recommended for future efforts.« less

PWR FLECHT SEASET 163-Rod Bundle Flow Blockage Task data report. NRC/EPRI/Westinghouse report No. 13, August-October 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loftus, M J; Hochreiter, L E; McGuire, M F

This report presents data from the 163-Rod Bundle Blow Blockage Task of the Full-Length Emergency Cooling Heat Transfer Systems Effects and Separate Effects Test Program (FLECHT SEASET). The task consisted of forced and gravity reflooding tests utilizing electrical heater rods with a cosine axial power profile to simulate PWR nuclear core fuel rod arrays. These tests were designed to determine effects of flow blockage and flow bypass on reflooding behavior and to aid in the assessment of computational models in predicting the reflooding behavior of flow blockage in rod bundle arrays.

75 FR 13 - Alternate Fracture Toughness Requirements for Protection Against Pressurized Thermal Shock Events

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-04

...The Nuclear Regulatory Commission (NRC) is amending its regulations to provide alternate fracture toughness requirements for protection against pressurized thermal shock (PTS) events for pressurized water reactor (PWR) pressure vessels. This final rule provides alternate PTS requirements based on updated analysis methods. This action is desirable because the existing requirements are based on unnecessarily conservative probabilistic fracture mechanics analyses. This action reduces regulatory burden for those PWR licensees who expect to exceed the existing requirements before the expiration of their licenses, while maintaining adequate safety, and may choose to comply with the final rule as an alternative to complying with the existing requirements.

Performance testing and analyses of the VSC-17 ventilated concrete cask. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKinnon, M.A.; Dodge, R.E.; Schmitt, R.C.

1992-05-01

This document details performance test which was conducted on a Pacific Sierra Nuclear VSC-17 ventilated concrete storage cask configured for pressurized-water reactor (PWR) spent fuel. The performance test consisted of loading the VSC-17 cask with 17 canisters of consolidated PWR spent fuel from Virginia Power`s Surry and Florida Power & Light Turkey Point reactors. Cask surface, concrete, air channel surfaces, and fuel canister guide tube temperatures were measured, as were cask surface gamma and neutron dose rates. Testing was performed with vacuum, nitrogen, and helium backfill environments in a vertical cask orientation. Data on spent fuel integrity were also obtained.

Validation of the new code package APOLLO2.8 for accurate PWR neutronics calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santamarina, A.; Bernard, D.; Blaise, P.

2013-07-01

This paper summarizes the Qualification work performed to demonstrate the accuracy of the new APOLLO2.S/SHEM-MOC package based on JEFF3.1.1 nuclear data file for the prediction of PWR neutronics parameters. This experimental validation is based on PWR mock-up critical experiments performed in the EOLE/MINERVE zero-power reactors and on P.I. Es on spent fuel assemblies from the French PWRs. The Calculation-Experiment comparison for the main design parameters is presented: reactivity of UOX and MOX lattices, depletion calculation and fuel inventory, reactivity loss with burnup, pin-by-pin power maps, Doppler coefficient, Moderator Temperature Coefficient, Void coefficient, UO{sub 2}-Gd{sub 2}O{sub 3} poisoning worth, Efficiency ofmore » Ag-In-Cd and B4C control rods, Reflector Saving for both standard 2-cm baffle and GEN3 advanced thick SS reflector. From this qualification process, calculation biases and associated uncertainties are derived. This code package APOLLO2.8 is already implemented in the ARCADIA new AREVA calculation chain for core physics and is currently under implementation in the future neutronics package of the French utility Electricite de France. (authors)« less

Best estimate plus uncertainty analysis of departure from nucleate boiling limiting case with CASL core simulator VERA-CS in response to PWR main steam line break event

DOE PAGES

Brown, Cameron S.; Zhang, Hongbin; Kucukboyaci, Vefa; ...

2016-09-07

VERA-CS (Virtual Environment for Reactor Applications, Core Simulator) is a coupled neutron transport and thermal-hydraulics subchannel code under development by the Consortium for Advanced Simulation of Light Water Reactors (CASL). VERA-CS was used to simulate a typical pressurized water reactor (PWR) full core response with 17x17 fuel assemblies for a main steam line break (MSLB) accident scenario with the most reactive rod cluster control assembly stuck out of the core. The accident scenario was initiated at the hot zero power (HZP) at the end of the first fuel cycle with return to power state points that were determined by amore » system analysis code and the most limiting state point was chosen for core analysis. The best estimate plus uncertainty (BEPU) analysis method was applied using Wilks’ nonparametric statistical approach. In this way, 59 full core simulations were performed to provide the minimum departure from nucleate boiling ratio (MDNBR) at the 95/95 (95% probability with 95% confidence level) tolerance limit. The results show that this typical PWR core remains within MDNBR safety limits for the MSLB accident.« less

Neutronics Studies of Uranium-bearing Fully Ceramic Micro-encapsulated Fuel for PWRs

DOE PAGES

George, Nathan M.; Maldonado, G. Ivan; Terrani, Kurt A.; ...

2014-12-01

Our study evaluated the neutronics and some of the fuel cycle characteristics of using uranium-based fully ceramic microencapsulated (FCM) fuel in a pressurized water reactor (PWR). Specific PWR lattice designs with FCM fuel have been developed that are expected to achieve higher specific burnup levels in the fuel while also increasing the tolerance to reactor accidents. The SCALE software system was the primary analysis tool used to model the lattice designs. A parametric study was performed by varying tristructural isotropic particle design features (e.g., kernel diameter, coating layer thicknesses, and packing fraction) to understand the impact on reactivity and resultingmore » operating cycle length. Moreover, to match the lifetime of an 18-month PWR cycle, the FCM particle fuel design required roughly 10% additional fissile material at beginning of life compared with that of a standard uranium dioxide (UO 2) rod. Uranium mononitride proved to be a favorable fuel for the fuel kernel due to its higher heavy metal loading density compared with UO 2. The FCM fuel designs evaluated maintain acceptable neutronics design features for fuel lifetime, lattice peaking factors, and nonproliferation figure of merit.« less

Best estimate plus uncertainty analysis of departure from nucleate boiling limiting case with CASL core simulator VERA-CS in response to PWR main steam line break event

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Cameron S.; Zhang, Hongbin; Kucukboyaci, Vefa

VERA-CS (Virtual Environment for Reactor Applications, Core Simulator) is a coupled neutron transport and thermal-hydraulics subchannel code under development by the Consortium for Advanced Simulation of Light Water Reactors (CASL). VERA-CS was used to simulate a typical pressurized water reactor (PWR) full core response with 17x17 fuel assemblies for a main steam line break (MSLB) accident scenario with the most reactive rod cluster control assembly stuck out of the core. The accident scenario was initiated at the hot zero power (HZP) at the end of the first fuel cycle with return to power state points that were determined by amore » system analysis code and the most limiting state point was chosen for core analysis. The best estimate plus uncertainty (BEPU) analysis method was applied using Wilks’ nonparametric statistical approach. In this way, 59 full core simulations were performed to provide the minimum departure from nucleate boiling ratio (MDNBR) at the 95/95 (95% probability with 95% confidence level) tolerance limit. The results show that this typical PWR core remains within MDNBR safety limits for the MSLB accident.« less

OLIGOCELLULA1/HIGH EXPRESSION OF OSMOTICALLY RESPONSIVE GENES15 Promotes Cell Proliferation With HISTONE DEACETYLASE9 and POWERDRESS During Leaf Development in Arabidopsis thaliana

PubMed Central

Suzuki, Marina; Shinozuka, Nanae; Hirakata, Tomohiro; Nakata, Miyuki T.; Demura, Taku; Tsukaya, Hirokazu; Horiguchi, Gorou

2018-01-01

Organ size regulation is dependent on the precise spatial and temporal regulation of cell proliferation and cell expansion. A number of transcription factors have been identified that play a key role in the determination of aerial lateral organ size, but their functional relationship to various chromatin modifiers has not been well understood. To understand how leaf size is regulated, we previously isolated the oligocellula1 (oli1) mutant of Arabidopsis thaliana that develops smaller first leaves than the wild type (WT) mainly due to a reduction in the cell number. In this study, we further characterized oli1 leaf phenotypes and identified the OLI1 gene as well as interaction partners of OLI1. Detailed characterizations of leaf development suggested that the cell proliferation rate in oli1 leaf primordia is lower than that in the WT. In addition, oli1 was associated with a slight delay of the progression from the juvenile to adult phases of leaf traits. A classical map-based approach demonstrated that OLI1 is identical to HIGH EXPRESSION OF OSMOTICALLY RESPONSIVE GENES15 (HOS15). HOS15/OLI1 encodes a homolog of human transducin β-like protein1 (TBL1). TBL1 forms a transcriptional repression complex with the histone deacetylase (HDAC) HDAC3 and either nuclear receptor co-repressor (N-CoR) or silencing mediator for retinoic acid and thyroid receptor (SMRT). We found that mutations in HISTONE DEACETYLASE9 (HDA9) and a switching-defective protein 3, adaptor 2, N-CoR, and transcription factor IIIB-domain protein gene, POWERDRESS (PWR), showed a small-leaf phenotype similar to oli1. In addition, hda9 and pwr did not further enhance the oli1 small-leaf phenotype, suggesting that these three genes act in the same pathway. Yeast two-hybrid assays suggested physical interactions, wherein PWR probably bridges HOS15/OLI1 and HDA9. Earlier studies suggested the roles of HOS15, HDA9, and PWR in transcriptional repression. Consistently, transcriptome analyses showed several genes commonly upregulated in the three mutants. From these findings, we propose a possibility that HOS15/OLI1, PWR, and HDA9 form an evolutionary conserved transcription repression complex that plays a positive role in the regulation of final leaf size. PMID:29774040

Zebra: An advanced PWR lattice code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, L.; Wu, H.; Zheng, Y.

2012-07-01

This paper presents an overview of an advanced PWR lattice code ZEBRA developed at NECP laboratory in Xi'an Jiaotong Univ.. The multi-group cross-section library is generated from the ENDF/B-VII library by NJOY and the 361-group SHEM structure is employed. The resonance calculation module is developed based on sub-group method. The transport solver is Auto-MOC code, which is a self-developed code based on the Method of Characteristic and the customization of AutoCAD software. The whole code is well organized in a modular software structure. Some numerical results during the validation of the code demonstrate that this code has a good precisionmore » and a high efficiency. (authors)« less

Estimating probable flaw distributions in PWR steam generator tubes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorman, J.A.; Turner, A.P.L.

1997-02-01

This paper describes methods for estimating the number and size distributions of flaws of various types in PWR steam generator tubes. These estimates are needed when calculating the probable primary to secondary leakage through steam generator tubes under postulated accidents such as severe core accidents and steam line breaks. The paper describes methods for two types of predictions: (1) the numbers of tubes with detectable flaws of various types as a function of time, and (2) the distributions in size of these flaws. Results are provided for hypothetical severely affected, moderately affected and lightly affected units. Discussion is provided regardingmore » uncertainties and assumptions in the data and analyses.« less

Optimization of burnable poison design for Pu incineration in fully fertile free PWR core

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fridman, E.; Shwageraus, E.; Galperin, A.

2006-07-01

The design challenges of the fertile-free based fuel (FFF) can be addressed by careful and elaborate use of burnable poisons (BP). Practical fully FFF core design for PWR reactor has been reported in the past [1]. However, the burnable poison option used in the design resulted in significant end of cycle reactivity penalty due to incomplete BP depletion. Consequently, excessive Pu loading were required to maintain the target fuel cycle length, which in turn decreased the Pu burning efficiency. A systematic evaluation of commercially available BP materials in all configurations currently used in PWRs is the main objective of thismore » work. The BP materials considered are Boron, Gd, Er, and Hf. The BP geometries were based on Wet Annular Burnable Absorber (WABA), Integral Fuel Burnable Absorber (IFBA), and Homogeneous poison/fuel mixtures. Several most promising combinations of BP designs were selected for the full core 3D simulation. All major core performance parameters for the analyzed cases are very close to those of a standard PWR with conventional UO{sub 2} fuel including possibility of reactivity control, power peaking factors, and cycle length. The MTC of all FFF cores was found at the full power conditions at all times and very close to that of the UO{sub 2} core. The Doppler coefficient of the FFF cores is also negative but somewhat lower in magnitude compared to UO{sub 2} core. The soluble boron worth of the FFF cores was calculated to be lower than that of the UO{sub 2} core by about a factor of two, which still allows the core reactivity control with acceptable soluble boron concentrations. The main conclusion of this work is that judicial application of burnable poisons for fertile free fuel has a potential to produce a core design with performance characteristics close to those of the reference PWR core with conventional UO{sub 2} fuel. (authors)« less

Analysis of steam generator tube rupture transients with single failure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trambauer, K.

The Gesellschaft fuer Reaktorsicherheit is engaged in the collection and evaluation of light water reactor operating experience as well as analyses for the risk study of the pressurized water reactor (PWR). Within these activities, thermohydraulic calculations have been performed to show the influence of different boundary conditions and disturbances on the steam generator tube rupture (SGTR) transients. The analyses of these calculations have focused on the measures and systems needed to cope with an SGTR. The reference plant for this analysis is a 1300-MW(e) PWR of Kraftwerk Union design with four loops, each containing a U-tube steam generator (SG) andmore » a reactor cooling pump (RCP). The thermal-hydraulic code DRUFAN-02 was used for the transient calculations.« less

SCC Initiation Behavior of Alloy 182 in PWR Primary Water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toloczko, Mychailo B.; Zhai, Ziqing; Bruemmer, Stephen M.

SCC initiation behavior of 15% cold forged specimens cut from four different alloy 182 weldments was investigated in 360°C simulated PWR primary water under constant load at the yield stress using direct current potential drop to perform in-situ monitoring of SCC initiation time. Within each weldment, one or more specimens underwent SCC initiation within 24 hours of reaching full load while some specimens had much longer initiation times, in a few cases exceeding 2500 hours. Detailed examinations were conducted on these specimens with a focus on different microstructural features such as preexisting defects, grain orientation and second phases, highlighting anmore » important role of microstructure in crack initiation of alloy 182.« less

76 FR 41783 - Combined Notice of Filings #2

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-15

... Commodities Group, Constellation Pwr Source Generation LLC, Constellation NewEnergy, Inc., CER Generation II..., CER Generation, LLC, Constellation Energy Commodities Group M, Constellation Mystic Power, LLC...

A Novel Strategy to Inhibit Hedgehog Signaling and Control Growth of Androgen-Independent Prostate Cancer Cells

DTIC Science & Technology

2013-12-01

M TIME PPC1 Volume of Spheroid Ctrl (respective media) .2% DMSO 10 uM Free Curcumin 20 uM Free Curcumin 10 uM Tagged Curcumin 20 uM Tagged... Curcumin FIGURE 6 Ctrl media 10uM FC 20uM FC 20uM TC 10uM TC 2% DMSO PC3 t0 Div 8 FIGURE 7 Phospho-p65 NFκB subunit expression decreased In

Experimental validation of the DARWIN2.3 package for fuel cycle applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

San-Felice, L.; Eschbach, R.; Bourdot, P.

2012-07-01

The DARWIN package, developed by the CEA and its French partners (AREVA and EDF) provides the required parameters for fuel cycle applications: fuel inventory, decay heat, activity, neutron, {gamma}, {alpha}, {beta} sources and spectrum, radiotoxicity. This paper presents the DARWIN2.3 experimental validation for fuel inventory and decay heat calculations on Pressurized Water Reactor (PWR). In order to validate this code system for spent fuel inventory a large program has been undertaken, based on spent fuel chemical assays. This paper deals with the experimental validation of DARWIN2.3 for the Pressurized Water Reactor (PWR) Uranium Oxide (UOX) and Mixed Oxide (MOX) fuelmore » inventory calculation, focused on the isotopes involved in Burn-Up Credit (BUC) applications and decay heat computations. The calculation - experiment (C/E-1) discrepancies are calculated with the latest European evaluation file JEFF-3.1.1 associated with the SHEM energy mesh. An overview of the tendencies is obtained on a complete range of burn-up from 10 to 85 GWd/t (10 to 60 GWcVt for MOX fuel). The experimental validation of the DARWIN2.3 package for decay heat calculation is performed using calorimetric measurements carried out at the Swedish Interim Spent Fuel Storage Facility for Pressurized Water Reactor (PWR) assemblies, covering a large burn-up (20 to 50 GWd/t) and cooling time range (10 to 30 years). (authors)« less

Fuel cycle cost, reactor physics and fuel manufacturing considerations for Erbia-bearing PWR fuel with > 5 wt% U-235 content

DOE Office of Scientific and Technical Information (OSTI.GOV)

Franceschini, F.; Lahoda, E. J.; Kucukboyaci, V. N.

2012-07-01

The efforts to reduce fuel cycle cost have driven LWR fuel close to the licensed limit in fuel fissile content, 5.0 wt% U-235 enrichment, and the acceptable duty on current Zr-based cladding. An increase in the fuel enrichment beyond the 5 wt% limit, while certainly possible, entails costly investment in infrastructure and licensing. As a possible way to offset some of these costs, the addition of small amounts of Erbia to the UO{sub 2} powder with >5 wt% U-235 has been proposed, so that its initial reactivity is reduced to that of licensed fuel and most modifications to the existingmore » facilities and equipment could be avoided. This paper discusses the potentialities of such a fuel on the US market from a vendor's perspective. An analysis of the in-core behavior and fuel cycle performance of a typical 4-loop PWR with 18 and 24-month operating cycles has been conducted, with the aim of quantifying the potential economic advantage and other operational benefits of this concept. Subsequently, the implications on fuel manufacturing and storage are discussed. While this concept has certainly good potential, a compelling case for its short-term introduction as PWR fuel for the US market could not be determined. (authors)« less

Posttest analysis of international standard problem 10 using RELAP4/MOD7. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsu, M.; Davis, C.B.; Peterson, A.C. Jr.

RELAP4/MOD7, a best estimate computer code for the calculation of thermal and hydraulic phenomena in a nuclear reactor or related system, is the latest version in the RELAP4 code development series. This paper evaluates the capability of RELAP4/MOD7 to calculate refill/reflood phenomena. This evaluation uses the data of International Standard Problem 10, which is based on West Germany's KWU PKL refill/reflood experiment K9A. The PKL test facility represents a typical West German four-loop, 1300 MW pressurized water reactor (PWR) in reduced scale while maintaining prototypical volume-to-power ratio. The PKL facility was designed to specifically simulate the refill/reflood phase of amore » hypothetical loss-of-coolant accident (LOCA).« less

Grid-to-rod flow-induced impact study for PWR fuel in reactor

DOE PAGES

Jiang, Hao; Qu, Jun; Lu, Roger Y.; ...

2016-06-10

The source for grid-to-rod fretting in a pressurized water nuclear reactor (PWR) is the dynamic contact impact from hydraulic flow-induced fuel assembly vibration. In order to support grid-to-rod fretting wear mitigation research, finite element analysis (FEA) was used to evaluate the hydraulic flow-induced impact intensity between the fuel rods and the spacer grids. Three-dimensional FEA models, with detailed geometries of the dimple and spring of the actual spacer grids along with fuel rods, were developed for flow impact simulation. The grid-to-rod dynamic impact simulation provided insights of the contact phenomena at grid-rod interface. Finally, it is an essential and effectivemore » way to evaluate contact forces and provide guidance for simulative bench fretting-impact tests.« less

PWR design for low doses in the United Kingdom: The present and the future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zodiates, A.M.; Willcock, A.

1995-03-01

The Pressurizer Water Reactor (PWR) design chosen for adoption by Nuclear Electric plc was based on the Westinghouse Standard Nuclear Unit Power Plant System (SNUPPS). This design was developed to meet the United Kingdom (UK) requirements and those improvements are embodied in the Sizewell B plant. Nuclear Electric plc is now looking to the design of the future PWRs to be built in the UK. These PWRs will be based as replicas of the Sizewell B design, but attention will be given to reducing operator doses further. This paper details the approach in operator protection improvements incorporated at Sizewall B,more » presents the estimated annual collective dose, and identifies the approach being adopted to reduce further operator doses in future plants.« less

Development of on-line monitoring system for Nuclear Power Plant (NPP) using neuro-expert, noise analysis, and modified neural networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subekti, M.; Center for Development of Reactor Safety Technology, National Nuclear Energy Agency of Indonesia, Puspiptek Complex BO.80, Serpong-Tangerang, 15340; Ohno, T.

2006-07-01

The neuro-expert has been utilized in previous monitoring-system research of Pressure Water Reactor (PWR). The research improved the monitoring system by utilizing neuro-expert, conventional noise analysis and modified neural networks for capability extension. The parallel method applications required distributed architecture of computer-network for performing real-time tasks. The research aimed to improve the previous monitoring system, which could detect sensor degradation, and to perform the monitoring demonstration in High Temperature Engineering Tested Reactor (HTTR). The developing monitoring system based on some methods that have been tested using the data from online PWR simulator, as well as RSG-GAS (30 MW research reactormore » in Indonesia), will be applied in HTTR for more complex monitoring. (authors)« less

Electrochemical study of pre- and post-transition corrosion of Zr alloys in PWR coolant

NASA Astrophysics Data System (ADS)

Macák, Jan; Novotný, Radek; Sajdl, Petr; Renčiuková, Veronika; Vrtílková, Věra

Corrosion properties of Zr-Sn and Zr-Nb zirconium alloys were studied under simulated PWR conditions (or, more exactly, VVER conditions — boric acid, potassium hydroxide, lithium hydroxide) at temperatures up to 340°C and 15MPa using in-situ electrochemical impedance spectroscopy (EIS) and polarization measurements. EIS spectra were obtained in a wide range of frequencies (typically 100kHz — 100μHz). It enabled to gain information of both dielectric properties of oxide layers developing on the Zr-alloys surface and of the kinetics of the corrosion process and the associated charge and mass transfer phenomena. Experiments were run for more than 380 days; thus, the study of all the corrosion stages (pre-transition, transition, post-transition) was possible.

Conceptual design study of small long-life PWR based on thorium cycle fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subkhi, M. Nurul; Su'ud, Zaki; Waris, Abdul

2014-09-30

A neutronic performance of small long-life Pressurized Water Reactor (PWR) using thorium cycle based fuel has been investigated. Thorium cycle which has higher conversion ratio in thermal region compared to uranium cycle produce some significant of {sup 233}U during burn up time. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.3, while the multi-energy-group diffusion calculations were optimized in whole core cylindrical two-dimension R-Z geometry by SRAC-CITATION. this study would be introduced thorium nitride fuel system which ZIRLO is the cladding material. The optimization of 350 MWt small long life PWRmore » result small excess reactivity and reduced power peaking during its operation.« less

Attenuation of midinfrared free electron laser energy with eyewear

NASA Astrophysics Data System (ADS)

Joos, Karen M.; Gabella, William

2005-04-01

Purpose: To determine the attenuation of free electron laser (FEL) energy at several wavelengths through microscope objective and eyeglass lenses. Materials and Methods: The FEL at wavelengths of 2.3 um, 2.5 um, 3.0 um, 3.5 um, 4.0 um, 4.5 um, 5.0 um, 6.45 um, 7.0 um, 7.5 um, and 8.0 um was telescoped using a 500 mm nominal focal length lens and a 200 mm focal length lens. The beam had a final spot of about 3 mm and was passed through a 3 mm aperture and onto the 8 mm active area of a J9LP Molectron detector. The eyeglass sample was placed 3 cm in front of the detector. Energy readings were averaged over multiple pulses. Results: Attenuation varied greatly with wavelength and sample from a low attenuation of 0.46 dB, 90% transmission, for short wavelengths through common glass to greater than 60 dB attenuation (transmission at the detector noise level) for IR safe glass by Aura, Inc. Conclusion: Only the designated laser safety goggles effectively attenuate free electron laser energy at 2.3 um and 2.5 um. A microscope objective lens, polycarbonate, and silica glass eyewear is capable of effectively attenuating FEL energy at wavelengths greater than 4.5 um, but the polycarbonate lenses demonstrated material damage.

Effects of the weld thermal cycle on the microstructure of alloy 690

NASA Astrophysics Data System (ADS)

Tuttle, James R.

Alloy 690 has been introduced as a material for use as the heat exchanger tubes in the steam generators (SGs) of pressurised water reactor (PWR) nuclear power plant. Its immediate predecessor, alloy 600, suffered from a number of degradation modes and another alternative, alloy 800, has also had in-service problems. In laboratory tests, alloy 690 in both mill annealed (MA) and special thermally treated (STT) condition has shown a high degree of resistance to degradation in simulated PWR primary side environments and other test media.Limited research has previously been undertaken to investigate the effects of welding on alloy 690, when the material is used in SG applications. It was deemed important to increase knowledge in this area since fabrication of PWR SGs involves gas tungsten arc welding (GTAW) of the heat exchanger tubes to a clad tubeplate. For this research investigation welded samples of alloy 690 have been produced in the laboratory using a range of thermal cycles based around recommended weld parameters for SG fabrication. These samples have been compared with archive welds from PWR SG manufacturers. A number of welds incorporating alloy 600 and a number using alloy 800 tubing material have also been fabricated in the laboratory for comparative purposes. Two experimental melts have been produced to study the effects of Nb substitution for Ti in alloy 690 type materials.Welded and unwelded specimens have been studied, analysed and tested using a variety of methods and techniques. A method of metallographic sample preparation for transmission electron microscope (TEM) thin foil specimens has been developed and documented which ensures foil perforation in a specific region. The effects of Nb substitution for Ti have been discussed. Chemical balances and microstructures in the fusion zone of welds manufactured from alloy 690 tubing incorporating alloy 82 weld consumable have been shown to be non-ideal. Within the heat affected zone (HAZ) of both laboratory produced and archive welds the microstructures have been identified as detrimentally altered from the STT condition original tubing material(s). A number of conclusions have been drawn and recommendations have been made for future work.

PRESSURIZED WATER REACTOR PROGRAM TECHNICAL PROGRESS REPORT FOR THE PERIOD MAY 5, 1955 TO JUNE 16, 1955

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The current PWR plant and core parameters are listed. Resign requirements are briefly summarized for a radiation monitoring system, a fuel handling water system, a coolant purification system, an electrical power distribution system, and component shielding. Results of studies on thermal bowing and stressing of UO/sub 2/ are reported. A graph is presented of reactor power vs. reactor flow for various hot channel conditions. Development of U-- Mo and U-Nb alloys has been stopped because of the recent selection of UO/sub 2/ fuel material for the PWR core and blanket. The fabrication characteristics of UO/sub 2/ powders are being studied.more » Seamless Zircaloy-2 tubing has been tested to determine elastic limits, bursting pressures, and corrosion resistance. Fabrication techniques and tests for corrosion and defects in Zircaloy-clad U-Mo and UO/sub 2/ fuel rods are described. The preparation of UO/sub 2/ by various methods is being studied to determine which method produces a material most suitable for PWR fuel elements. The stability of UO/sub 2/ compacts in high temperature water and steam is being determined. Surface area and density measurements have been performed on samples of UO/sub 2/ powder prepared by various methods. Revelopment work on U-- Mo and U--Nb alloys has included studies of the effect on corrosion behavior of additions to the test water, additions to the alloys, homogenization of the alloys, annealing times, cladding, and fabrication techniques. Data are presented on relaxation in spring materials after exposure to a corrosive environment. Results are reported from loop and autoclave tests on fission product and crud deposition. Results of irradiation and corrosion testing of clad and unclad U--Mo and U-Nh alloys are described. The UO/sub 2/ irradiation program has included studies of dimensional changes, release of fission gases, and activity in the water surrounding the samples. A review of the methods of calculating reactor physics parameters has been completed, and the established procedures have been applied to determination of PWR reference design parameters. Critical experiments and primary loop shielding analyses are described. (D.E.B.)« less

Heuristic rules embedded genetic algorithm for in-core fuel management optimization

NASA Astrophysics Data System (ADS)

Alim, Fatih

The objective of this study was to develop a unique methodology and a practical tool for designing loading pattern (LP) and burnable poison (BP) pattern for a given Pressurized Water Reactor (PWR) core. Because of the large number of possible combinations for the fuel assembly (FA) loading in the core, the design of the core configuration is a complex optimization problem. It requires finding an optimal FA arrangement and BP placement in order to achieve maximum cycle length while satisfying the safety constraints. Genetic Algorithms (GA) have been already used to solve this problem for LP optimization for both PWR and Boiling Water Reactor (BWR). The GA, which is a stochastic method works with a group of solutions and uses random variables to make decisions. Based on the theories of evaluation, the GA involves natural selection and reproduction of the individuals in the population for the next generation. The GA works by creating an initial population, evaluating it, and then improving the population by using the evaluation operators. To solve this optimization problem, a LP optimization package, GARCO (Genetic Algorithm Reactor Code Optimization) code is developed in the framework of this thesis. This code is applicable for all types of PWR cores having different geometries and structures with an unlimited number of FA types in the inventory. To reach this goal, an innovative GA is developed by modifying the classical representation of the genotype. To obtain the best result in a shorter time, not only the representation is changed but also the algorithm is changed to use in-core fuel management heuristics rules. The improved GA code was tested to demonstrate and verify the advantages of the new enhancements. The developed methodology is explained in this thesis and preliminary results are shown for the VVER-1000 reactor hexagonal geometry core and the TMI-1 PWR. The improved GA code was tested to verify the advantages of new enhancements. The core physics code used for VVER in this research is Moby-Dick, which was developed to analyze the VVER by SKODA Inc. The SIMULATE-3 code, which is an advanced two-group nodal code, is used to analyze the TMI-1.

ADDITIONAL STRESS AND FRACTURE MECHANICS ANALYSES OF PRESSURIZED WATER REACTOR PRESSURE VESSEL NOZZLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walter, Matthew; Yin, Shengjun; Stevens, Gary

2012-01-01

In past years, the authors have undertaken various studies of nozzles in both boiling water reactors (BWRs) and pressurized water reactors (PWRs) located in the reactor pressure vessel (RPV) adjacent to the core beltline region. Those studies described stress and fracture mechanics analyses performed to assess various RPV nozzle geometries, which were selected based on their proximity to the core beltline region, i.e., those nozzle configurations that are located close enough to the core region such that they may receive sufficient fluence prior to end-of-life (EOL) to require evaluation of embrittlement as part of the RPV analyses associated with pressure-temperaturemore » (P-T) limits. In this paper, additional stress and fracture analyses are summarized that were performed for additional PWR nozzles with the following objectives: To expand the population of PWR nozzle configurations evaluated, which was limited in the previous work to just two nozzles (one inlet and one outlet nozzle). To model and understand differences in stress results obtained for an internal pressure load case using a two-dimensional (2-D) axi-symmetric finite element model (FEM) vs. a three-dimensional (3-D) FEM for these PWR nozzles. In particular, the ovalization (stress concentration) effect of two intersecting cylinders, which is typical of RPV nozzle configurations, was investigated. To investigate the applicability of previously recommended linear elastic fracture mechanics (LEFM) hand solutions for calculating the Mode I stress intensity factor for a postulated nozzle corner crack for pressure loading for these PWR nozzles. These analyses were performed to further expand earlier work completed to support potential revision and refinement of Title 10 to the U.S. Code of Federal Regulations (CFR), Part 50, Appendix G, Fracture Toughness Requirements, and are intended to supplement similar evaluation of nozzles presented at the 2008, 2009, and 2011 Pressure Vessels and Piping (PVP) Conferences. This work is also relevant to the ongoing efforts of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel (B&PV) Code, Section XI, Working Group on Operating Plant Criteria (WGOPC) efforts to incorporate nozzle fracture mechanics solutions into a revision to ASME B&PV Code, Section XI, Nonmandatory Appendix G.« less

Postpartum weight trajectories in overweight and lean women.

PubMed

Bogaerts, Annick; De Baetselier, Elyne; Ameye, Lieveke; Dilles, Tinne; Van Rompaey, Bart; Devlieger, Roland

2017-06-01

overweight and obesity in women of reproductive age are increasing and are often linked with excessive weight gain in pregnancy and weight retention after birth. Studies on spontaneous maternal weight trajectory after childbirth are scarce. we describe women's spontaneous weight trajectory during the first six weeks of the postpartum period and its relationship between Body Mass Index and socio-demographical, behavioural and psychological variables. data from 212 women who gave birth in three regional hospitals were collected prospectively between December 2015 and February 2016. Potential determinants were examined during pregnancy and the postpartum period at four and six weeks after childbirth. Descriptive statistics and a linear multivariate regression model were used. Early postnatal weight retention (PWR) was defined as the difference between the maternal weight six weeks after childbirth and the pre-pregnancy weight (kg). mean PWR at six weeks after childbirth was 3.3kg (SD 4.1), with a range between -7 and +16.2kg; 81% reported some weight retention (PWR>0kg), and 36% showed a high weight retention (PWR≥5kg). Women with a BMI <25kg/m 2 showed a significantly higher mean PWR six weeks after childbirth compared to women with a BMI ≥25kg/m 2 (4.0kg versus 1.6kg, p=0.002). There was a significant correlation between maternal weight retention and gestational weight gain (GWG) (B=0.65, p<0.001) and pre-pregnancy body mass index <25kg/m 2 (B=1.12, p=0.017), six weeks after childbirth. weight retention six weeks after childbirth is associated with pre-pregnancy BMI and GWG, but contrary to expectations, lean women with excessive GWG tended to retain most weight after childbirth. No significant associations with several socio-demographical, behavioural and psychological variables were found. weight management strategies around pregnancy should not be limited to overweight and obese mothers. Women with pre-pregnancy BMI <25kg/m 2 require equal attention to prevent postnatal weight retention. Copyright © 2016 Elsevier Ltd. All rights reserved.

Reactor Physics Assessment of Thick Silicon Carbide Clad PWR Fuels

DTIC Science & Technology

2013-06-01

Densities ............................................................................................................ 21 2.3 Fuel Mass (Core Total...70 7.1 Geometry, Material Density, and Mass Summary for All Cores...21 Table 3: Fuel Rod Masses for Different Clads

Experiment data report for Semiscale Mod-1 Test S-05-1 (alternate ECC injection test)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, E. M.; Patton, Jr., M. L.; Sackett, K. E.

Recorded test data are presented for Test S-05-1 of the Semiscale Mod-1 alternate ECC injection test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-05-1 was conducted from initial conditions of 2263 psia and 544/sup 0/F to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the cold leg broken loop piping. During the test, cooling water was injected into the vessel lower plenum to simulatemore » emergency core coolant injection in a PWR, with the flow rate based on system volume scaling.« less

Self-referenced directional enhanced Raman scattering using plasmon waveguide resonance for surface and bulk sensing

NASA Astrophysics Data System (ADS)

Wan, Xiu-mei; Gao, Ran; Lu, Dan-feng; Qi, Zhi-mei

2018-01-01

Surface plasmon-coupled emission has been widely used in fluorescence imaging, biochemical sensing, and enhanced Raman spectroscopy. A self-referenced directional enhanced Raman scattering for simultaneous detection of surface and bulk effects by using plasmon waveguide resonance (PWR) based surface plasmon-coupled emission has been proposed and experimentally demonstrated. Raman scattering was captured on the prism side in Kretschmann-surface plasmon-coupled emission. The distinct penetration depths (δ) of the evanescent field for the transverse electric (TE) and transverse magnetic (TM) modes result in different detected distances of the Raman signal. The experimental results demonstrate that the self-referenced directional enhanced Raman scattering of the TE and TM modes based on the PWR can detect and distinguish the surface and bulk effects simultaneously, which appears to have potential applications in researches of chemistry, medicine, and biology.

Full-scale 3-D finite element modeling of a two-loop pressurized water reactor for heat transfer, thermal–mechanical cyclic stress analysis, and environmental fatigue life estimation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohanty, Subhasish; Soppet, William K.; Majumdar, Saurindranath

This paper discusses a system-level finite element model of a two-loop pressurized water reactor (PWR). Based on this model, system-level heat transfer analysis and subsequent sequentially coupled thermal-mechanical stress analysis were performed for typical thermal-mechanical fatigue cycles. The in-air fatigue lives of example components, such as the hot and cold legs, were estimated on the basis of stress analysis results, ASME in-air fatigue life estimation criteria, and fatigue design curves. Furthermore, environmental correction factors and associated PWR environment fatigue lives for the hot and cold legs were estimated by using estimated stress and strain histories and the approach described inmore » US-NRC report: NUREG-6909.« less

IMPACT OF FISSION PRODUCTS IMPURITY ON THE PLUTONIUM CONTENT IN PWR MOX FUELS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilles Youinou; Andrea Alfonsi

2012-03-01

This report presents the results of a neutronics analysis done in response to the charter IFCA-SAT-2 entitled 'Fuel impurity physics calculations'. This charter specifies that the separation of the fission products (FP) during the reprocessing of UOX spent nuclear fuel assemblies (UOX SNF) is not perfect and that, consequently, a certain amount of FP goes into the Pu stream used to fabricate PWR MOX fuel assemblies. Only non-gaseous FP have been considered (see the list of 176 isotopes considered in the calculations in Appendix 1). This mixture of Pu and FP is called PuFP. Note that, in this preliminary analysis,more » the FP losses are considered element-independent, i.e., for example, 1% of FP losses mean that 1% of all non-gaseous FP leak into the Pu stream.« less

The Impact of Operating Parameters and Correlated Parameters for Extended BWR Burnup Credit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ade, Brian J.; Marshall, William B. J.; Ilas, Germina

Applicants for certificates of compliance for spent nuclear fuel (SNF) transportation and dry storage systems perform analyses to demonstrate that these systems are adequately subcritical per the requirements of Title 10 of the Code of Federal Regulations (10 CFR) Parts 71 and 72. For pressurized water reactor (PWR) SNF, these analyses may credit the reduction in assembly reactivity caused by depletion of fissile nuclides and buildup of neutron-absorbing nuclides during power operation. This credit for reactivity reduction during depletion is commonly referred to as burnup credit (BUC). US Nuclear Regulatory Commission (NRC) staff review BUC analyses according to the guidancemore » in the Division of Spent Fuel Storage and Transportation Interim Staff Guidance (ISG) 8, Revision 3, Burnup Credit in the Criticality Safety Analyses of PWR Spent Fuel in Transportation and Storage Casks.« less

Development of cement solidification process for sodium borate waste generated from PWR plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirofumi Okabe; Tatsuaki Sato; Yuichi Shoji

2013-07-01

A cement solidification process for treating sodium borate waste produced in pressurized water reactor (PWR) plants was studied. To obtain high volume reduction and high mechanical strength of the waste, simulated concentrated borate liquid waste with a sodium / boron (Na/B) mole ratio of 0.27 was dehydrated and powdered by using a wiped film evaporator. To investigate the effect of the Na/B mole ratio on the solidification process, a sodium tetraborate decahydrate reagent with a Na/B mole ratio of 0.5 was also used. Ordinary portland cement (OPC) and some additives were used for the solidification. Solidified cement prepared from powderedmore » waste with a Na/B mole ratio 0.24 and having a high silica sand content (silica sand/cement>2) showed to improved uniaxial compressive strength. (authors)« less

Analysis of the return to power scenario following a LBLOCA in a PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macian, R.; Tyler, T.N.; Mahaffy, J.H.

1995-09-01

The risk of reactivity accidents has been considered an important safety issue since the beginning of the nuclear power industry. In particular, several events leading to such scenarios for PWR`s have been recognized and studied to assess the potential risk of fuel damage. The present paper analyzes one such event: the possible return to power during the reflooding phase following a LBLOCA. TRAC-PF1/MOD2 coupled with a three-dimensional neutronic model of the core based on the Nodal Expansion Method (NEM) was used to perform the analysis. The system computer model contains a detailed representation of a complete typical 4-loop PWR. Thus,more » the simulation can follow complex system interactions during reflooding, which may influence the neutronics feedback in the core. Analyses were made with core models bases on cross sections generated by LEOPARD. A standard and a potentially more limiting case, with increased pressurizer and accumulator inventories, were run. In both simulations, the reactor reaches a stable state after the reflooding is completed. The lower core region, filled with cold water, generates enough power to boil part of the incoming liquid, thus preventing the core average liquid fraction from reaching a value high enough to cause a return to power. At the same time, the mass flow rate through the core is adequate to maintain the rod temperature well below the fuel damage limit.« less

Community concepts of poverty: an application to premium exemptions in Ghana’s National Health Insurance Scheme

PubMed Central

2013-01-01

Background Poverty is multi dimensional. Beyond the quantitative and tangible issues related to inadequate income it also has equally important social, more intangible and difficult if not impossible to quantify dimensions. In 2009, we explored these social and relativist dimension of poverty in five communities in the South of Ghana with differing socio economic characteristics to inform the development and implementation of policies and programs to identify and target the poor for premium exemptions under Ghana’s National Health Insurance Scheme. Methods We employed participatory wealth ranking (PWR) a qualitative tool for the exploration of community concepts, identification and ranking of households into socioeconomic groups. Key informants within the community ranked households into wealth categories after discussing in detail concepts and indicators of poverty. Results Community defined indicators of poverty covered themes related to type of employment, educational attainment of children, food availability, physical appearance, housing conditions, asset ownership, health seeking behavior, social exclusion and marginalization. The poverty indicators discussed shared commonalities but contrasted in the patterns of ranking per community. Conclusion The in-depth nature of the PWR process precludes it from being used for identification of the poor on a large national scale in a program such as the NHIS. However, PWR can provide valuable qualitative input to enrich discussions, development and implementation of policies, programs and tools for large scale interventions and targeting of the poor for social welfare programs such as premium exemption for health care. PMID:23497484

Hydrothermal synthesis of Ni 2FeBO 5 in near-supercritical PWR coolant and possible effects of neutron-induced 10B fission in fuel crud

NASA Astrophysics Data System (ADS)

Sawicki, Jerzy A.

2011-08-01

The hydrothermal synthesis of a nickel-iron oxyborate, Ni 2FeBO 5, known as bonaccordite, was investigated at pressures and temperatures that might occur at the surface of high-power fuel rods in PWR cores and in supercritical water reactors, especially during localized departures from nucleate boiling and dry-outs. The tests were performed using aqueous mixtures of nickel and iron oxides with boric acid or boron oxide, and as a function of lithium hydroxide addition, temperature and time of heating. At subcritical temperatures nickel ferrite NiFe 2O 4 was always the primary reaction product. High yield of Ni 2FeBO 5 synthesis started near critical water temperature and was strongly promoted by additions of LiOH up to Li/Fe and Li/B molar ratios in a range 0.1-1. The synthesis of bonaccordite was also promoted by other alkalis such as NaOH and KOH. The bonaccordite particles were likely formed by dissolution and re-crystallization by means of an intermediate nickel ferrite phase. It is postulated that the formation of Ni 2FeBO 5 in deposits of borated nickel and iron oxides on PWR fuel cladding can be accelerated by lithium produced in thermal neutron capture 10B(n,α) 7Li reactions. The process may also be aided in the reactor core by kinetic energy of α-particles and 7Li ions dissipated in the crud layer.

Community concepts of poverty: an application to premium exemptions in Ghana's National Health Insurance Scheme.

PubMed

Aryeetey, Genevieve C; Jehu-Appiah, Caroline; Kotoh, Agnes M; Spaan, Ernst; Arhinful, Daniel K; Baltussen, Rob; van der Geest, Sjaak; Agyepong, Irene A

2013-03-14

Poverty is multi dimensional. Beyond the quantitative and tangible issues related to inadequate income it also has equally important social, more intangible and difficult if not impossible to quantify dimensions. In 2009, we explored these social and relativist dimension of poverty in five communities in the South of Ghana with differing socio economic characteristics to inform the development and implementation of policies and programs to identify and target the poor for premium exemptions under Ghana's National Health Insurance Scheme. We employed participatory wealth ranking (PWR) a qualitative tool for the exploration of community concepts, identification and ranking of households into socioeconomic groups. Key informants within the community ranked households into wealth categories after discussing in detail concepts and indicators of poverty. Community defined indicators of poverty covered themes related to type of employment, educational attainment of children, food availability, physical appearance, housing conditions, asset ownership, health seeking behavior, social exclusion and marginalization. The poverty indicators discussed shared commonalities but contrasted in the patterns of ranking per community. The in-depth nature of the PWR process precludes it from being used for identification of the poor on a large national scale in a program such as the NHIS. However, PWR can provide valuable qualitative input to enrich discussions, development and implementation of policies, programs and tools for large scale interventions and targeting of the poor for social welfare programs such as premium exemption for health care.

Electron Microscopy Characterizations and Atom Probe Tomography of Intergranular Attack in Alloy 600 Exposed to PWR Primary Water

NASA Astrophysics Data System (ADS)

Olszta, Matthew J.; Schreiber, Daniel K.; Thomas, Larry E.; Bruemmer, Stephen M.

Detailed examinations of intergranular attack (IGA) in alloy 600 were performed after exposure to simulated PWR primary water at 325°C for 500 h. High-resolution analyses of IGA characteristics were conducted on specimens with either a 1 µm diamond or 1200-grit SiC surface finish using scanning electron microscopy, transmission electron microscopy and atom probe tomography techniques. The diamond-polish finish with very little preexisting subsurface damage revealed attack of high-energy grain boundaries that intersected the exposed surface to depths approaching 2 µm. In all cases, IGA from the surface is localized oxidation consisting of porous, nanocrystalline MO-structure and spinel particles along with regions of faceted wall oxidation. Surprisingly, this continuous IG oxidation transitions to discontinuous, discrete Cr-rich sulfide particles up to 50 nm in diameter. In the vicinity of the sulfides, the grain boundaries were severely Cr depleted (to <1 at%) and enriched in S. The 1200 grit SiC finish surface exhibited a preexisting highly strained recrystallized layer of elongated nanocrystalline matrix grains. Similar IG oxidation and leading sulfide particles were found, but the IGA depth was typically confined to the near-surface ( 400 nm) recrystallized region. Difference in IGA for the two surface finishes indicates that the formation of grain boundary sulfides occurs during the exposure to PWR primary water. The source of S remains unclear, however it is not present as sulfides in the bulk alloy nor is it segregated to bulk grain boundaries.

76 FR 66090 - Facility Operating License Amendment From Virginia Electric and Power Company, Surry Power...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-25

... operating pressures, leakage from primary water stress corrosion cracking below the proposed limited... discussed in Regulatory Guide (RG) 1.121, ``Bases for Plugging Degraded PWR [Pressurized-Water Reactor...

A comparison of the CHF between tubes and annuli under PWR thermal-hydraulic conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herer, C.; Souyri, A.; Garnier, J.

1995-09-01

Critical Heat Flux (CHF) tests were carried out in three tubes with inside diameters of 8, 13, and 19.2 mm and in two annuli with an inner tube of 9.5 mm and an outer tube of 13 or 19.2 mm. All axial heat flux distributions in the test sections were uniform. The coolant fluid was Refrigerant 12 (Freon-12) under PWR thermal-hydraulic conditions (equivalent water conditions - Pressure: 7 to 20 MPa, Mass Velocity: 1000 to 6000 kg/m2/s, Local Quality: -75% to +45%). The effect of tube diameter is correlated for qualities under 15%. The change from the tube to themore » annulus configuration is correctly taken into account by the equivalent hydraulic diameter. Useful information is also provided concerning the effect of a cold wall in an annulus.« less

International Space Station United States Orbital Segment Oxygen Generation System On-Orbit Operational Experience

NASA Technical Reports Server (NTRS)

Erickson, Robert J.; Howe, John, Jr.; Kulp, Galen W.; VanKeuren, Steven P.

2008-01-01

The International Space Station (ISS) United States Orbital Segment (USOS) Oxygen Generation System (OGS) was originally intended to be installed in ISS Node 3. The OGS rack delivery was accelerated, and it was launched to ISS in July of 2006 and installed in the US Laboratory Module. Various modification kits were installed to provide its interfaces, and the OGS was first activated in July of 2007 for 15 hours, In October of 2007 it was again activated for 76 hours with varied production rates and day/night cycling. Operational time in each instance was limited by the quantity of feedwater in a Payload Water Reservoir (PWR) bag. Feedwater will be provided by PWR bag until the USOS Water Recovery System (WRS) is delivered to SS in fall of 2008. This paper will discuss operating experience and characteristics of the OGS, as well as operational issues and their resolution.

A flooding induced station blackout analysis for a pressurized water reactor using the RISMC toolkit

DOE PAGES

Mandelli, Diego; Prescott, Steven; Smith, Curtis; ...

2015-05-17

In this paper we evaluate the impact of a power uprate on a pressurized water reactor (PWR) for a tsunami-induced flooding test case. This analysis is performed using the RISMC toolkit: the RELAP-7 and RAVEN codes. RELAP-7 is the new generation of system analysis codes that is responsible for simulating the thermal-hydraulic dynamics of PWR and boiling water reactor systems. RAVEN has two capabilities: to act as a controller of the RELAP-7 simulation (e.g., component/system activation) and to perform statistical analyses. In our case, the simulation of the flooding is performed by using an advanced smooth particle hydrodynamics code calledmore » NEUTRINO. The obtained results allow the user to investigate and quantify the impact of timing and sequencing of events on system safety. The impact of power uprate is determined in terms of both core damage probability and safety margins.« less

Bio-knowledge based filters improve residue-residue contact prediction accuracy.

PubMed

Wozniak, P P; Pelc, J; Skrzypecki, M; Vriend, G; Kotulska, M

2018-05-29

Residue-residue contact prediction through direct coupling analysis has reached impressive accuracy, but yet higher accuracy will be needed to allow for routine modelling of protein structures. One way to improve the prediction accuracy is to filter predicted contacts using knowledge about the particular protein of interest or knowledge about protein structures in general. We focus on the latter and discuss a set of filters that can be used to remove false positive contact predictions. Each filter depends on one or a few cut-off parameters for which the filter performance was investigated. Combining all filters while using default parameters resulted for a test-set of 851 protein domains in the removal of 29% of the predictions of which 92% were indeed false positives. All data and scripts are available from http://comprec-lin.iiar.pwr.edu.pl/FPfilter/. malgorzata.kotulska@pwr.edu.pl. Supplementary data are available at Bioinformatics online.

Pretest analysis of natural circulation on the PWR model PACTEL with horizontal steam generators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kervinen, T.; Riikonen, V.; Ritonummi, T.

A new tests facility - parallel channel tests loop (PACTEL)- has been designed and built to simulate the major components and system behavior of pressurized water reactors (PWRs) during postulated small- and medium-break loss-of-coolant accidents. Pretest calculations have been performed for the first test series, and the results of these calculations are being used for planning experiments, for adjusting the data acquisition system, and for choosing the optimal position and type of instrumentation. PACTEL is a volumetrically scaled (1:305) model of the VVER-440 PWR. In all the calculated cases, the natural circulation was found to be effective in removing themore » heat from the core to the steam generator. The loop mass flow rate peaked at 60% mass inventory. The straightening of the loop seals increased the mass flow rate significantly.« less

PWR steam generator chemical cleaning, Phase I. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rothstein, S.

1978-07-01

United Nuclear Industries (UNI) entered into a subcontract with Consolidated Edison Company of New York (Con Ed) on August 8, 1977, for the purpose of developing methods to chemically clean the secondary side tube to tube support crevices of the steam generators of Indian Point Nos. 1 and 2 PWR plants. This document represents the first reporting on activities performed for Phase I of this effort. Specifically, this report contains the results of a literature search performed by UNI for the purpose of determining state-of-the-art chemical solvents and methods for decontaminating nuclear reactor steam generators. The results of the searchmore » sought to accomplish two objectives: (1) identify solvents beyond those proposed at present by UNI and Con Ed for the test program, and (2) confirm the appropriateness of solvents and methods of decontamination currently in use by UNI.« less

Development of an extended-burnup Mark B design. First semi-annual progress report, July-December 1978. Report BAW-1532-1. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1979-10-01

The primary objective of this program is to develop and demonstrate an improved PWR fuel assembly design capable of batch average burnups of 45,000-50,000 MWd/mtU. To accomplish this, a number of technical areas must be investigated to verify acceptable extended-burnup fuel performance. This report is the first semi-annual progress report for the program, and it describes work performed during the July-December 1978 time period. Efforts during this period included the definition of a preliminary design for a high-burnup fuel rod, physics analyses of extended-burnup fuel cycles, studies of the physics characteristics of changes in fuel assembly metal-to-water ratios, and developmentmore » of a design concept for post-irradiation examination equipment to be utilized in examining high-burnup lead-test assemblies.« less

Modeling local chemistry in PWR steam generator crevices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Millett, P.J.

1997-02-01

Over the past two decades steam generator corrosion damage has been a major cost impact to PWR owners. Crevices and occluded regions create thermal-hydraulic conditions where aggressive impurities can become highly concentrated, promoting localized corrosion of the tubing and support structure materials. The type of corrosion varies depending on the local conditions, with stress corrosion cracking being the phenomenon of most current concern. A major goal of the EPRI research in this area has been to develop models of the concentration process and resulting crevice chemistry conditions. These models may then be used to predict crevice chemistry based on knowledgemore » of bulk chemistry, thereby allowing the operator to control corrosion damage. Rigorous deterministic models have not yet been developed; however, empirical approaches have shown promise and are reflected in current versions of the industry-developed secondary water chemistry guidelines.« less

Simulation of German PKL refill/reflood experiment K9A using RELAP4/MOD7. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsu, M.T.; Davis, C.B.; Behling, S.R.

This paper describes a RELAP4/MOD7 simulation of West Germany's Kraftwerk Union (KWU) Primary Coolant Loop (PKL) refill/reflood experiment K9A. RELAP4/MOD7, a best-estimate computer program for the calculation of thermal and hydraulic phenomena in a nuclear reactor or related system, is the latest version in the RELAP4 code development series. This study was the first major simulation using RELAP4/MOD7 since its release by the Idaho National Engineering Laboratory (INEL). The PKL facility is a reduced scale (1:134) representation of a typical West German four-loop 1300 MW pressurized water reactor (PWR). A prototypical scale of the total volume to power ratio wasmore » maintained. The test facility was designed specifically for an experiment simulating the refill/reflood phase of a Loss-of-Coolant Accident (LOCA).« less

Progress in understanding fission-product behaviour in coated uranium-dioxide fuel particles

NASA Astrophysics Data System (ADS)

Barrachin, M.; Dubourg, R.; Kissane, M. P.; Ozrin, V.

2009-03-01

Supported by results of calculations performed with two analytical tools (MFPR, which takes account of physical and chemical mechanisms in calculating the chemical forms and physical locations of fission products in UO2, and MEPHISTA, a thermodynamic database), this paper presents an investigation of some important aspects of the fuel microstructure and chemical evolutions of irradiated TRISO particles. The following main conclusions can be identified with respect to irradiated TRISO fuel: first, the relatively low oxygen potential within the fuel particles with respect to PWR fuel leads to chemical speciation that is not typical of PWR fuels, e.g., the relatively volatile behaviour of barium; secondly, the safety-critical fission-product caesium is released from the urania kernel but the buffer and pyrolytic-carbon coatings could form an important chemical barrier to further migration (i.e., formation of carbides). Finally, significant releases of fission gases from the urania kernel are expected even in nominal conditions.

Effective dominance of resistance of Spodoptera frugiperda to Bt maize and cotton varieties: implications for resistance management

PubMed Central

Horikoshi, Renato J.; Bernardi, Daniel; Bernardi, Oderlei; Malaquias, José B.; Okuma, Daniela M.; Miraldo, Leonardo L.; Amaral, Fernando S. de A. e; Omoto, Celso

2016-01-01

The resistance of fall armyworm (FAW), Spodoptera frugiperda, has been characterized to some Cry and Vip3A proteins of Bacillus thuringiensis (Bt) expressed in transgenic maize in Brazil. Here we evaluated the effective dominance of resistance based on the survival of neonates from selected Bt-resistant, heterozygous, and susceptible (Sus) strains of FAW on different Bt maize and cotton varieties. High survival of strains resistant to the Cry1F (HX-R), Cry1A.105/Cry2Ab (VT-R) and Cry1A.105/Cry2Ab/Cry1F (PW-R) proteins was detected on Herculex, YieldGard VT PRO and PowerCore maize. Our Vip3A-resistant strain (Vip-R) exhibited high survival on Herculex, Agrisure Viptera and Agrisure Viptera 3 maize. However, the heterozygous from HX-R × Sus, VT-R × Sus, PW-R × Sus and Vip-R × Sus had complete mortality on YieldGard VT PRO, PowerCore, Agrisure Viptera, and Agrisure Viptera 3, whereas the HX-R × Sus and Vip-R × Sus strains survived on Herculex maize. On Bt cotton, the HX-R, VT-R and PW-R strains exhibited high survival on Bollgard II. All resistant strains survived on WideStrike, but only PW-R and Vip-R × Sus survived on TwinLink. Our study provides useful data to aid in the understanding of the effectiveness of the refuge strategy for Insect Resistance Management of Bt plants. PMID:27721425

Modeling of a Flooding Induced Station Blackout for a Pressurized Water Reactor Using the RISMC Toolkit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mandelli, Diego; Prescott, Steven R; Smith, Curtis L

2011-07-01

In the Risk Informed Safety Margin Characterization (RISMC) approach we want to understand not just the frequency of an event like core damage, but how close we are (or are not) to key safety-related events and how might we increase our safety margins. The RISMC Pathway uses the probabilistic margin approach to quantify impacts to reliability and safety by coupling both probabilistic (via stochastic simulation) and mechanistic (via physics models) approaches. This coupling takes place through the interchange of physical parameters and operational or accident scenarios. In this paper we apply the RISMC approach to evaluate the impact of amore » power uprate on a pressurized water reactor (PWR) for a tsunami-induced flooding test case. This analysis is performed using the RISMC toolkit: RELAP-7 and RAVEN codes. RELAP-7 is the new generation of system analysis codes that is responsible for simulating the thermal-hydraulic dynamics of PWR and boiling water reactor systems. RAVEN has two capabilities: to act as a controller of the RELAP-7 simulation (e.g., system activation) and to perform statistical analyses (e.g., run multiple RELAP-7 simulations where sequencing/timing of events have been changed according to a set of stochastic distributions). By using the RISMC toolkit, we can evaluate how power uprate affects the system recovery measures needed to avoid core damage after the PWR lost all available AC power by a tsunami induced flooding. The simulation of the actual flooding is performed by using a smooth particle hydrodynamics code: NEUTRINO.« less

Spelling Well Despite Developmental Language Disorder: What Makes it Possible?

PubMed Central

Rakhlin, Natalia; Cardoso-Martins, Cláudia; Kornilov, Sergey A.; Grigorenko, Elena L.

2013-01-01

The goal of the study was to investigate the overlap between Developmental Language Disorder (DLD) and Developmental Dyslexia, identified through spelling difficulties (SD), in Russian-speaking children. In particular, we studied the role of phoneme awareness (PA), rapid automatized naming (RAN), pseudoword repetition (PWR), morphological (MA) and orthographic awareness (OA) in differentiating between children with DLD who have SD from children with DLD who are average spellers by comparing the two groups to each other, to typically developing children as well as children with SD but without spoken language deficits. One hundred forty nine children, aged 10.40 to 14.00, participated in the study. The results indicated that the SD, DLD, and DLD/SD groups did not differ from each other on PA and RAN Letters and underperformed in comparison to the control groups. However, whereas the children with written language deficits (SD and DLD/SD groups) underperformed on RAN Objects and Digits, PWR, OA and MA, the children with DLD and no SD performed similarly to the children from the control groups on these measures. In contrast, the two groups with spoken language deficits (DLD and DLD/SD) underperformed on RAN Colors in comparison to the control groups and the group of children with SD only. The results support the notion that those children with DLD who have unimpaired PWR and RAN skills are able to overcome their weaknesses in spoken language and PA and acquire basic literacy on a par with their age peers with typical language. We also argue that our findings support a multifactorial model of developmental language disorders (DLD). PMID:23860907

EMERALD REV.1. PWR Accident Activity Release

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brunot, W.K.; Fray, R.R.; Gillespie, S.G.

1975-10-01

The EMERALD program is designed for the calculation of radiation releases and exposures resulting from abnormal operation of a large pressurized water reactor (PWR). The approach used in EMERALD is similar to an analog simulation of a real system. Each component or volume in the plant which contains a radioactive material is represented by a subroutine which keeps track of the production, transfer, decay and absorption of radioactivity in that volume. During the course of the analysis of an accident, activity is transferred from subroutine to subroutine in the program as it would be transferred from place to place inmore » the plant. For example, in the calculation of the doses resulting from a loss-of-coolant accident the program first calculates the activity built up in the fuel before the accident, then releases some of this activity to the containment volume. Some of this activity is then released to the atmosphere. The rates of transfer, leakage, production, cleanup, decay, and release are read in as input to the program. Subroutines are also included which calculate the on-site and off-site radiation exposures at various distances for individual isotopes and sums of isotopes. The program contains a library of physical data for the twenty-five isotopes of most interest in licensing calculations, and other isotopes can be added or substituted. Because of the flexible nature of the simulation approach, the EMERALD program can be used for most calculations involving the production and release of radioactive materials during abnormal operation of a PWR. These include design, operational, and licensing studies.« less

Effective dominance of resistance of Spodoptera frugiperda to Bt maize and cotton varieties: implications for resistance management

NASA Astrophysics Data System (ADS)

Horikoshi, Renato J.; Bernardi, Daniel; Bernardi, Oderlei; Malaquias, José B.; Okuma, Daniela M.; Miraldo, Leonardo L.; Amaral, Fernando S. De A. E.; Omoto, Celso

2016-10-01

The resistance of fall armyworm (FAW), Spodoptera frugiperda, has been characterized to some Cry and Vip3A proteins of Bacillus thuringiensis (Bt) expressed in transgenic maize in Brazil. Here we evaluated the effective dominance of resistance based on the survival of neonates from selected Bt-resistant, heterozygous, and susceptible (Sus) strains of FAW on different Bt maize and cotton varieties. High survival of strains resistant to the Cry1F (HX-R), Cry1A.105/Cry2Ab (VT-R) and Cry1A.105/Cry2Ab/Cry1F (PW-R) proteins was detected on Herculex, YieldGard VT PRO and PowerCore maize. Our Vip3A-resistant strain (Vip-R) exhibited high survival on Herculex, Agrisure Viptera and Agrisure Viptera 3 maize. However, the heterozygous from HX-R × Sus, VT-R × Sus, PW-R × Sus and Vip-R × Sus had complete mortality on YieldGard VT PRO, PowerCore, Agrisure Viptera, and Agrisure Viptera 3, whereas the HX-R × Sus and Vip-R × Sus strains survived on Herculex maize. On Bt cotton, the HX-R, VT-R and PW-R strains exhibited high survival on Bollgard II. All resistant strains survived on WideStrike, but only PW-R and Vip-R × Sus survived on TwinLink. Our study provides useful data to aid in the understanding of the effectiveness of the refuge strategy for Insect Resistance Management of Bt plants.

Hopkins during ITCS PWR Retrieval

NASA Image and Video Library

2014-01-31

ISS038-E-040140 (31 Jan. 2014) --- NASA astronaut Mike Hopkins, Expedition 38 flight engineer, uses the Fluid Servicing System (FSS) to refill Internal Thermal Control System (ITCS) loops with fresh coolant in the Destiny laboratory of the International Space Station.

Hopkins during ITCS PWR Retrieval

NASA Image and Video Library

2014-01-31

ISS038-E-040139 (31 Jan. 2014) --- NASA astronaut Mike Hopkins, Expedition 38 flight engineer, uses the Fluid Servicing System (FSS) to refill Internal Thermal Control System (ITCS) loops with fresh coolant in the Destiny laboratory of the International Space Station.

BME Estimation of Residential Exposure to Ambient PM10 and Ozone at Multiple Time Scales

PubMed Central

Yu, Hwa-Lung; Chen, Jiu-Chiuan; Christakos, George; Jerrett, Michael

2009-01-01

Background Long-term human exposure to ambient pollutants can be an important contributing or etiologic factor of many chronic diseases. Spatiotemporal estimation (mapping) of long-term exposure at residential areas based on field observations recorded in the U.S. Environmental Protection Agency’s Air Quality System often suffer from missing data issues due to the scarce monitoring network across space and the inconsistent recording periods at different monitors. Objective We developed and compared two upscaling methods: UM1 (data aggregation followed by exposure estimation) and UM2 (exposure estimation followed by data aggregation) for the long-term PM10 (particulate matter with aerodynamic diameter ≤ 10 μm) and ozone exposure estimations and applied them in multiple time scales to estimate PM and ozone exposures for the residential areas of the Health Effects of Air Pollution on Lupus (HEAPL) study. Method We used Bayesian maximum entropy (BME) analysis for the two upscaling methods. We performed spatiotemporal cross-validations at multiple time scales by UM1 and UM2 to assess the estimation accuracy across space and time. Results Compared with the kriging method, the integration of soft information by the BME method can effectively increase the estimation accuracy for both pollutants. The spatiotemporal distributions of estimation errors from UM1 and UM2 were similar. The cross-validation results indicated that UM2 is generally better than UM1 in exposure estimations at multiple time scales in terms of predictive accuracy and lack of bias. For yearly PM10 estimations, both approaches have comparable performance, but the implementation of UM1 is associated with much lower computation burden. Conclusion BME-based upscaling methods UM1 and UM2 can assimilate core and site-specific knowledge bases of different formats for long-term exposure estimation. This study shows that UM1 can perform reasonably well when the aggregation process does not alter the spatiotemporal structure of the original data set; otherwise, UM2 is preferable. PMID:19440491

Resistance of uveal melanoma to the interstrand cross-linking agent mitomycin C is associated with reduced expression of CYP450R

PubMed Central

Gravells, P; Hoh, L; Canovas, D; Rennie, I G; Sisley, K; Bryant, H E

2011-01-01

Background: Uveal melanoma (UM) is the most common primary intraocular tumour of adults, frequently metastasising to the liver. Hepatic metastases are difficult to treat and are mainly unresponsive to chemotherapy. To investigate why UM are so chemo-resistant we explored the effect of interstrand cross-linking agents mitomycin C (MMC) and cisplatin in comparison with hydroxyurea (HU). Methods: Sensitivity to MMC, cisplatin and HU was tested in established UM cell lines using clonogenic assays. The response of UM to MMC was confirmed in MTT assays using short-term cultures of primary UM. The expression of cytochrome P450 reductase (CYP450R) was analysed by western blotting, and DNA cross-linking was assessed using COMET analysis supported by γ-H2AX foci formation. Results: Both established cell lines and primary cultures of UM were resistant to the cross-linking agent MMC (in each case P<0.001 in Student's t-test compared with controls). In two established UM cell lines, DNA cross-link damage was not induced by MMC (in both cases P<0.05 in Students's t-test compared with damage induced in controls). In all, 6 out of 6 UMs tested displayed reduced expression of the metabolising enzyme CYP450R and transient expression of CYP450R increased MMC sensitivity of UM. Conclusion: We suggest that reduced expression of CYP450R is responsible for MMC resistance of UM, through a lack of bioactivation, which can be reversed by complementing UM cell lines with CYP450R. PMID:21386838

Monte Carlo characterization of PWR spent fuel assemblies to determine the detectability of pin diversion

NASA Astrophysics Data System (ADS)

Burdo, James S.

This research is based on the concept that the diversion of nuclear fuel pins from Light Water Reactor (LWR) spent fuel assemblies is feasible by a careful comparison of spontaneous fission neutron and gamma levels in the guide tube locations of the fuel assemblies. The goal is to be able to determine whether some of the assembly fuel pins are either missing or have been replaced with dummy or fresh fuel pins. It is known that for typical commercial power spent fuel assemblies, the dominant spontaneous neutron emissions come from Cm-242 and Cm-244. Because of the shorter half-life of Cm-242 (0.45 yr) relative to that of Cm-244 (18.1 yr), Cm-244 is practically the only neutron source contributing to the neutron source term after the spent fuel assemblies are more than two years old. Initially, this research focused upon developing MCNP5 models of PWR fuel assemblies, modeling their depletion using the MONTEBURNS code, and by carrying out a preliminary depletion of a ¼ model 17x17 assembly from the TAKAHAMA-3 PWR. Later, the depletion and more accurate isotopic distribution in the pins at discharge was modeled using the TRITON depletion module of the SCALE computer code. Benchmarking comparisons were performed with the MONTEBURNS and TRITON results. Subsequently, the neutron flux in each of the guide tubes of the TAKAHAMA-3 PWR assembly at two years after discharge as calculated by the MCNP5 computer code was determined for various scenarios. Cases were considered for all spent fuel pins present and for replacement of a single pin at a position near the center of the assembly (10,9) and at the corner (17,1). Some scenarios were duplicated with a gamma flux calculation for high energies associated with Cm-244. For each case, the difference between the flux (neutron or gamma) for all spent fuel pins and with a pin removed or replaced is calculated for each guide tube. Different detection criteria were established. The first was whether the relative error of the difference was less than 1.00, allowing for the existence of the difference within the margin of error. The second was whether the difference between the two values was big enough to prevent their error bars from overlapping. Error analysis was performed both using a one second count and pseudo-Maxwell statistics for a projected 60 second count, giving four criteria for detection. The number of guide tubes meeting these criteria was compared and graphed for each case. Further analysis at extremes of high and low enrichment and long and short burnup times was done using data from assemblies at the Beaver Valley 1 and 2 PWR. In all neutron flux cases, at least two guide tube locations meet all the criteria for detection of pin diversion. At least one location in almost all of the gamma flux cases does. These results show that placing detectors in the empty guide tubes of spent fuel bundles to identify possible pin diversion is feasible.

PWR and BWR spent fuel assembly gamma spectra measurements

NASA Astrophysics Data System (ADS)

Vaccaro, S.; Tobin, S. J.; Favalli, A.; Grogan, B.; Jansson, P.; Liljenfeldt, H.; Mozin, V.; Hu, J.; Schwalbach, P.; Sjöland, A.; Trellue, H.; Vo, D.

2016-10-01

A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative-Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. To compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

EMERALD REVISION 1; PWR accident activity release. [IBM360,370; FORTRAN IV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fowler, T.B.; Tobias, M.L.; Fox, J.N.

The EMERALD program is designed for the calculation of radiation releases and exposures resulting from abnormal operation of a large pressurized water reactor (PWR). The approach used in EMERALD is similar to an analog simulation of a real system. Each component or volume in the plant which contains a radioactive material is represented by a subroutine which keeps track of the production, transfer, decay and absorption of radioactivity in that volume. During the course of the analysis of an accident, activity is transferred from subroutine to subroutine in the program as it would be transferred from place to place inmore » the plant. For example, in the calculation of the doses resulting from a loss-of-coolant accident the program first calculates the activity built up in the fuel before the accident, then releases some of this activity to the containment volume. Some of this activity is then released to the atmosphere. The rates of transfer, leakage, production, cleanup, decay, and release are read in as input to the program. Subroutines are also included which calculate the on-site and off-site radiation exposures at various distances for individual isotopes and sums of isotopes. The program contains a library of physical data for the twenty-five isotopes of most interest in licensing calculations, and other isotopes can be added or substituted. Because of the flexible nature of the simulation approach, the EMERALD program can be used for most calculations involving the production and release of radioactive materials during abnormal operation of a PWR. These include design, operational, and licensing studies.IBM360,370; FORTRAN IV; OS/360,370 (IBM360,370); 520K bytes of memory are required..« less

PWR and BWR spent fuel assembly gamma spectra measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaccaro, S.; Tobin, Stephen J.; Favalli, Andrea

A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detectmore » the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. As a result, to compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.« less

Effects of materials and design on the criticality and shielding assessment of canister concepts for the disposal of spent nuclear fuel.

PubMed

Gutiérrez, Miguel Morales; Caruso, Stefano; Diomidis, Nikitas

2018-05-19

According to the Swiss disposal concept, the safety of a deep geological repository for spent nuclear fuel (SNF) is based on a multi-barrier system. The disposal canister is an important component of the engineered barrier system, aiming to provide containment of the SNF for thousands of years. This study evaluates the criticality safety and shielding of candidate disposal canister concepts, focusing on the fulfilment of the sub-criticality criterion and on limiting radiolysis processes at the outer surface of the canister which can enhance corrosion mechanisms. The effective neutron multiplication factor (k-eff) and the surface dose rates are calculated for three different canister designs and material combinations for boiling water reactor (BWR) canisters, containing 12 spent fuel assemblies (SFA), and pressurized water reactor (PWR) canisters, with 4 SFAs. For each configuration, individual criticality and shielding calculations were carried out. The results show that k-eff falls below the defined upper safety limit (USL) of 0.95 for all BWR configurations, while staying above USL for the PWR ones. Therefore, the application of a burnup credit methodology for the PWR case is required, being currently under development. Relevant is also the influence of canister material and internal geometry on criticality, enabling the identification of safer fuel arrangements. For a final burnup of 55MWd/kgHM and 30y cooling time, the combined photon-neutron surface dose rate is well below the threshold of 1 Gy/h defined to limit radiation-induced corrosion of the canister in all cases. Copyright © 2018 Elsevier Ltd. All rights reserved.

PWR and BWR spent fuel assembly gamma spectra measurements

DOE PAGES

Vaccaro, S.; Tobin, Stephen J.; Favalli, Andrea; ...

2016-07-17

A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detectmore » the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. As a result, to compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.« less

Implementing a Nuclear Power Plant Model for Evaluating Load-Following Capability on a Small Grid

NASA Astrophysics Data System (ADS)

Arda, Samet Egemen

A pressurized water reactor (PWR) nuclear power plant (NPP) model is introduced into Positive Sequence Load Flow (PSLF) software by General Electric in order to evaluate the load-following capability of NPPs. The nuclear steam supply system (NSSS) consists of a reactor core, hot and cold legs, plenums, and a U-tube steam generator. The physical systems listed above are represented by mathematical models utilizing a state variable lumped parameter approach. A steady-state control program for the reactor, and simple turbine and governor models are also developed. Adequacy of the isolated reactor core, the isolated steam generator, and the complete PWR models are tested in Matlab/Simulink and dynamic responses are compared with the test results obtained from the H. B. Robinson NPP. Test results illustrate that the developed models represents the dynamic features of real-physical systems and are capable of predicting responses due to small perturbations of external reactivity and steam valve opening. Subsequently, the NSSS representation is incorporated into PSLF and coupled with built-in excitation system and generator models. Different simulation cases are run when sudden loss of generation occurs in a small power system which includes hydroelectric and natural gas power plants besides the developed PWR NPP. The conclusion is that the NPP can respond to a disturbance in the power system without exceeding any design and safety limits if appropriate operational conditions, such as achieving the NPP turbine control by adjusting the speed of the steam valve, are met. In other words, the NPP can participate in the control of system frequency and improve the overall power system performance.

Probabilistic analysis on the failure of reactivity control for the PWR

NASA Astrophysics Data System (ADS)

Sony Tjahyani, D. T.; Deswandri; Sunaryo, G. R.

2018-02-01

The fundamental safety function of the power reactor is to control reactivity, to remove heat from the reactor, and to confine radioactive material. The safety analysis is used to ensure that each parameter is fulfilled during the design and is done by deterministic and probabilistic method. The analysis of reactivity control is important to be done because it will affect the other of fundamental safety functions. The purpose of this research is to determine the failure probability of the reactivity control and its failure contribution on a PWR design. The analysis is carried out by determining intermediate events, which cause the failure of reactivity control. Furthermore, the basic event is determined by deductive method using the fault tree analysis. The AP1000 is used as the object of research. The probability data of component failure or human error, which is used in the analysis, is collected from IAEA, Westinghouse, NRC and other published documents. The results show that there are six intermediate events, which can cause the failure of the reactivity control. These intermediate events are uncontrolled rod bank withdrawal at low power or full power, malfunction of boron dilution, misalignment of control rod withdrawal, malfunction of improper position of fuel assembly and ejection of control rod. The failure probability of reactivity control is 1.49E-03 per year. The causes of failures which are affected by human factor are boron dilution, misalignment of control rod withdrawal and malfunction of improper position for fuel assembly. Based on the assessment, it is concluded that the failure probability of reactivity control on the PWR is still within the IAEA criteria.

Uveal melanoma hepatic metastases mutation spectrum analysis using targeted next-generation sequencing of 400 cancer genes.

PubMed

Luscan, A; Just, P A; Briand, A; Burin des Roziers, C; Goussard, P; Nitschké, P; Vidaud, M; Avril, M F; Terris, B; Pasmant, E

2015-04-01

Uveal melanoma (UM) is the most common malignant tumour of the eye. Diagnosis often occurs late in the course of disease, and prognosis is generally poor. Recently, recurrent somatic mutations were described, unravelling additional specific altered pathways in UM. Targeted next-generation sequencing (NGS) can now be applied to an accurate and fast identification of somatic mutations in cancer. The aim of the present study was to characterise the mutation pattern of five UM hepatic metastases with well-defined clinical and pathological features. We analysed the UM mutation spectrum using targeted NGS on 409 cancer genes. Four previous reported genes were found to be recurrently mutated. All tumours presented mutually exclusive GNA11 or GNAQ missense mutations. BAP1 loss-of-function mutations were found in three UMs. SF3B1 missense mutations were found in the two UMs with no BAP1 mutations. We then searched for additional mutation targets. We identified the Arg505Cys mutation in the tumour suppressor FBXW7. The same mutation was previously described in different cancer types, and FBXW7 was recently reported to be mutated in UM exomes. Further studies are required to confirm FBXW7 implication in UM tumorigenesis. Elucidating the molecular mechanisms underlying UM tumorigenesis holds the promise for novel and effective targeted UM therapies. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

78 FR 35960 - Minor Boundary Revision at Mojave National Preserve

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-14

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-MOJA-12321; PS.SMOJA0003] Minor Boundary Revision at Mojave National Preserve AGENCY: National Park Service, Interior. ACTION: Notification of... following locations: National Park Service, Land Resources Program Center, Pacific West Region, 333 Bush...

Grain boundary damage evolution and SCC initiation of cold-worked alloy 690 in simulated PWR primary water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhai, Ziqing; Toloczko, Mychailo B.; Kruska, Karen

Long-term grain boundary (GB) damage evolution and stress corrosion crack initiation in alloy 690 are being investigated by constant load tensile testing in high-temperature, simulated PWR primary water. Six commercial alloy 690 heats are being tested in various cold work conditions loaded at their yield stress. This paper reviews the basic test approach and detailed characterizations performed on selected specimens after an exposure time of ~1 year. Intergranular crack nucleation was observed under constant stress in certain highly cold-worked (CW) alloy 690 heats and was found to be associated with the formation of GB cavities. Somewhat surprisingly, the heats mostmore » susceptible to cavity formation and crack nucleation were thermally treated materials with most uniform coverage of small GB carbides. Microstructure, % cold work and applied stress comparisons are made among the alloy 690 heats to better understand the factors influencing GB cavity formation and crack initiation.« less

Microstructural Effects on SCC Initiation PWR Primary Water Cold-Worked Alloy 600

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhai, Ziqing; Toloczko, Mychailo B.; Bruemmer, Stephen M.

SCC initiation behavior of one mill annealed alloy 600 plate heat was investigated in simulated PWR primary water under constant load at yield stress with in-situ direct current potential drop (DCPD) monitoring for crack initiation. Twelve specimens were tested at similar cold work levels among which three showed much shorter SCC initiation times (<400 hrs) than the others (>1200 hrs). Post-test examinations revealed that these three specimens all feature an inhomogeneous microstructure where the primary crack always nucleated along the boundary of large elongated grains protruding normally into the gauge. In contrast, such microstructure was either not observed or didmore » not extend deep enough into the gauge in the other specimens exhibiting ~3-6X longer initiation times. In order to better understand the role of this microstructural inhomogeneity in SCC initiation, high-resolution microscopy was performed to compare carbide morphology and strain distribution between the long grains and normal grains, and their potential effects on SCC initiation are discussed in this paper.« less

Reactor antineutrino detector iDREAM.

NASA Astrophysics Data System (ADS)

Gromov, M. B.; Lukyanchenko, G. A.; Novikova, G. J.; Obinyakov, B. A.; Oralbaev, A. Y.; Skorokhvatov, M. D.; Sukhotin, S. V.; Chepurnov, A. S.; Etenko, A. V.

2017-09-01

Industrial Detector for Reactor Antineutrino Monitoring (iDREAM) is a compact (≈ 3.5m 2) industrial electron antineutrino spectrometer. It is dedicated for remote monitoring of PWR reactor operational modes by neutrino method in real-time. Measurements of antineutrino flux from PWR allow to estimate a fuel mixture in active zone and to check the status of the reactor campaign for non-proliferation purposes. LAB-based gadolinium doped scintillator is exploited as a target. Multizone architecture of the detector with gamma-catcher surrounding fiducial volume and plastic muon veto above and below ensure high efficiency of IBD detection and background suppression. DAQ is based on Flash ADC with PSD discrimination algorithms while digital trigger is programmable and flexible due to FPGA. The prototype detector was started up in 2014. Preliminary works on registration Cerenkov radiation produced by cosmic muons were established with distilled water inside the detector in order to test electronic and slow control systems. Also in parallel a long-term measurements with different scintillator samples were conducted.

Regeneratively Cooled Liquid Oxygen/Methane Technology Development

NASA Technical Reports Server (NTRS)

Robinson, Joel W.; Greene, Christopher B.; Stout, Jeffrey

2012-01-01

The National Aeronautics & Space Administration (NASA) has identified Liquid Oxygen (LOX)/Liquid Methane (LCH4) as a potential propellant combination for future space vehicles based upon exploration studies. The technology is estimated to have higher performance and lower overall systems mass compared to existing hypergolic propulsion systems. NASA-Marshall Space Flight Center (MSFC) in concert with industry partner Pratt & Whitney Rocketdyne (PWR) utilized a Space Act Agreement to test an oxygen/methane engine system in the Summer of 2010. PWR provided a 5,500 lbf (24,465 N) LOX/LCH4 regenerative cycle engine to demonstrate advanced thrust chamber assembly hardware and to evaluate the performance characteristics of the system. The chamber designs offered alternatives to traditional regenerative engine designs with improvements in cost and/or performance. MSFC provided the test stand, consumables and test personnel. The hot fire testing explored the effective cooling of one of the thrust chamber designs along with determining the combustion efficiency with variations of pressure and mixture ratio. The paper will summarize the status of these efforts.

On the condition of UO2 nuclear fuel irradiated in a PWR to a burn-up in excess of 110 MWd/kgHM

NASA Astrophysics Data System (ADS)

Restani, R.; Horvath, M.; Goll, W.; Bertsch, J.; Gavillet, D.; Hermann, A.; Martin, M.; Walker, C. T.

2016-12-01

Post-irradiation examination results are presented for UO2 fuel from a PWR fuel rod that had been irradiated to an average burn-up of 105 MWd/kgHM and showed high fission gas release of 42%. The radial distribution of xenon and the partitioning of fission gas between bubbles and the fuel matrix was investigated using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and electron probe microanalysis. It is concluded that release from the fuel at intermediate radial positions was mainly responsible for the high fission gas release. In this region thermal release had occurred from the high burn-up structure (HBS) at some point after the sixth irradiation cycle. The LA-ICP-MS results indicate that gas release had also occurred from the HBS in the vicinity of the pellet periphery. It is shown that the gas pressure in the HBS pores is well below the pressure that the fuel can sustain.

Development code for sensitivity and uncertainty analysis of input on the MCNPX for neutronic calculation in PWR core

NASA Astrophysics Data System (ADS)

Hartini, Entin; Andiwijayakusuma, Dinan

2014-09-01

This research was carried out on the development of code for uncertainty analysis is based on a statistical approach for assessing the uncertainty input parameters. In the butn-up calculation of fuel, uncertainty analysis performed for input parameters fuel density, coolant density and fuel temperature. This calculation is performed during irradiation using Monte Carlo N-Particle Transport. The Uncertainty method based on the probabilities density function. Development code is made in python script to do coupling with MCNPX for criticality and burn-up calculations. Simulation is done by modeling the geometry of PWR terrace, with MCNPX on the power 54 MW with fuel type UO2 pellets. The calculation is done by using the data library continuous energy cross-sections ENDF / B-VI. MCNPX requires nuclear data in ACE format. Development of interfaces for obtaining nuclear data in the form of ACE format of ENDF through special process NJOY calculation to temperature changes in a certain range.

Effects of iron content in Ni-Cr-xFe alloys and immersion time on the oxide films formed in a simulated PWR water environment

NASA Astrophysics Data System (ADS)

Ru, Xiangkun; Lu, Zhanpeng; Chen, Junjie; Han, Guangdong; Zhang, Jinlong; Hu, Pengfei; Liang, Xue

2017-12-01

The iron content in Ni-Cr-xFe (x = 0-9 at.%) alloys strongly affected the properties of oxide films after 978 h of immersion in the simulated PWR primary water environment at 310 °C. Increasing the iron content in the alloys increased the amount of iron-bearing polyhedral spinel oxide particles in the outer oxide layer and increased the local oxidation penetrations into the alloy matrix from the chromium-rich inner oxide layer. The effects of iron content in the alloys on the oxide film properties after 500 h of immersion were less significant than those after 978 h. Iron content increased, and chromium content decreased, in the outer oxide layer with increasing iron content in the alloys. Increasing the immersion time facilitated the formation of the local oxidation penetrations along the matrix/film interface and the nickel-bearing spinel oxides in the outer oxide layer.

Corrosion fatigue characterization of reactor pressure vessel steels. [PWR; BWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Der Sluys, W.A.

1982-12-01

During routine operation, light water reactor (LWR) pressure vessels are subjected to a variety of transients that result in time-varying stresses. Consequently, fatigue and environmentally-assisted fatigue are mechanisms of growth relevant to flaws in these pressure vessels. To provide a better understanding of the resistance of nuclear pressure vessel steels to these flaw growth processes, fracture mechanics data were generated on the rates of fatigue crack growth for SA508-2 and SA533B-1 steels in both room temperature air and 288/sup 0/C water. Areas investigated were: the relationship of crack growth rate to prior loading history; the effects of loading frequency andmore » R ratio (K/sub min//K/sub max/) on crack growth rate as a function of the stress intensity factor range (..delta..K); transient aspects of the fatigue crack growth behavior; the effect of material chemistry (sulphur content) on fatigue crack; and growth rate; water chemistry effects (high-purity water versus simulated pressurized water reactotr (PWR) primary coolant).« less

Development code for sensitivity and uncertainty analysis of input on the MCNPX for neutronic calculation in PWR core

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartini, Entin, E-mail: entin@batan.go.id; Andiwijayakusuma, Dinan, E-mail: entin@batan.go.id

2014-09-30

This research was carried out on the development of code for uncertainty analysis is based on a statistical approach for assessing the uncertainty input parameters. In the butn-up calculation of fuel, uncertainty analysis performed for input parameters fuel density, coolant density and fuel temperature. This calculation is performed during irradiation using Monte Carlo N-Particle Transport. The Uncertainty method based on the probabilities density function. Development code is made in python script to do coupling with MCNPX for criticality and burn-up calculations. Simulation is done by modeling the geometry of PWR terrace, with MCNPX on the power 54 MW with fuelmore » type UO2 pellets. The calculation is done by using the data library continuous energy cross-sections ENDF / B-VI. MCNPX requires nuclear data in ACE format. Development of interfaces for obtaining nuclear data in the form of ACE format of ENDF through special process NJOY calculation to temperature changes in a certain range.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shin, Yong-Hoon, E-mail: chaotics@snu.ac.kr; Park, Sangrok; Kim, Byong Sup

Since the first nuclear power was engaged in Korean electricity grid in 1978, intensive research and development has been focused on localization and standardization of large pressurized water reactors (PWRs) aiming at providing Korean peninsula and beyond with economical and safe power source. With increased priority placed on the safety since Chernobyl accident, Korean nuclear power R and D activity has been diversified into advanced PWR, small modular PWR and generation IV reactors. After the outbreak of Fukushima accident, inherently safe small modular reactor (SMR) receives growing interest in Korea and Europe. In this paper, we will describe recent statusmore » of evolving designs of SMR, their advantages and challenges. In particular, the conceptual design of lead-bismuth cooled SMR in Korea, URANUS with 40∼70 MWe is examined in detail. This paper will cover a framework of the program and a strategy for the successful deployment of small modular reactor how the goals would entail and the approach to collaboration with other entities.« less

Test prediction for the German PKL Test K5A using RELAP4/MOD6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Y.S.; Haigh, W.S.; Sullivan, L.H.

RELAP4/MOD6 is the most recent modification in the series of RELAP4 computer programs developed to describe the thermal-hydraulic conditions attendant to postulated transients in light water reactor systems. The major new features in RELAP4/MOD6 include best-estimate pressurized water reactor (PWR) reflood transient analytical models for core heat transfer, local entrainment, and core vapor superheat, and a new set of heat transfer correlations for PWR blowdown and reflood. These new features were used for a test prediction of the Kraftwerk Union three-loop PRIMAR KREISLAUF (PKL) Reflood Test K5A. The results of the prediction were in good agreement with the experimental thermalmore » and hydraulic system data. Comparisons include heater rod surface temperature, system pressure, mass flow rates, and core mixture level. It is concluded that RELAP4/MOD6 is capable of accurately predicting transient reflood phenomena in the 200% cold-leg break test configuration of the PKL reflood facility.« less

Application of a Simple Model to Predict Environmental Radionuclide Levels and Consequential Dose Rates on the South Welsh Coast, U.K.

NASA Astrophysics Data System (ADS)

Halliwell, C. M.; McKay, W. A.

1994-02-01

The impact of liquid effluent discharges, from both existing nuclear power stations and from a possible future pressurized water reactor (PWR), on the levels of radioactivity in Welsh Severn coastal waters has been addressed in this study through the use of a simple box model. If a PWR was in operation at Hinkley Point, and assuming that the existing discharges into the estuary remained the same as in 1989, the levels of the most radiologically significant radionuclide, 137Cs, in seawater along the Welsh shoreline are predicted to increase by 7% (inner estuary), 7% (Welsh outer estuary) and 5% (inner channel) and in sediment by 0·3, 1·3 and 2% respectively. The radiation dose rate from 137Cs to members of the coastal population alone would show only a marginal increase due to these changes, and would remain less than 1% of the internationally recognized limit.

Improved Biomolecular Thin-Film Sensor based on Plasmon Waveguide Resonance

NASA Astrophysics Data System (ADS)

Byard, Courtney; Aslan, Mustafa; Mendes, Sergio

2009-05-01

The design, fabrication, and characterization of a plasmon waveguide resonance (PWR) sensor are presented. Glass substrates are coated with a 35 nm gold film using electron beam evaporation, and then covered with a 143 nm aluminum oxide waveguide using an atomic layer deposition process, creating a smooth, highly transparent dielectric film. When probed in the Kretschmann configuration, the structure allows for an efficient conversion of an incident optical beam into a surface wave, which is mainly confined in the dielectric layer and exhibits a deep and narrow angular resonance. The performance (reflectance vs. incidence angle in TE polarization) is modeled using a transfer-matrix approach implemented into a Mathematica code. Our simulations and experimental data are compared with that of surface plasmon resonance (SPR) sensor using the same criteria. We show that the resolution of PWR is approximately ten times better than SPR, opening opportunities for more sensitive studies in various applications including research in protein interactions, pharmaceutical drug development, and food analysis.

Common cause evaluations in applied risk analysis of nuclear power plants. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taniguchi, T.; Ligon, D.; Stamatelatos, M.

1983-04-01

Qualitative and quantitative approaches were developed for the evaluation of common cause failures (CCFs) in nuclear power plants and were applied to the analysis of the auxiliary feedwater systems of several pressurized water reactors (PWRs). Key CCF variables were identified through a survey of experts in the field and a review of failure experience in operating PWRs. These variables were classified into categories of high, medium, and low defense against a CCF. Based on the results, a checklist was developed for analyzing CCFs of systems. Several known techniques for quantifying CCFs were also reviewed. The information provided valuable insights inmore » the development of a new model for estimating CCF probabilities, which is an extension of and improvement over the Beta Factor method. As applied to the analysis of the PWR auxiliary feedwater systems, the method yielded much more realistic values than the original Beta Factor method for a one-out-of-three system.« less

Inhibition of selenocysteine tRNA[Ser]Sec aminoacylation provides evidence that aminoacylation is required for regulatory methylation of this tRNA

PubMed Central

Kim, Jin Young; Carlson, Bradley A.; Xu, Xue-Ming; Zeng, Yu; Chen, Shawn; Gladyshev, Vadim N.; Lee, Byeong Jae; Hatfield, Dolph L.

2011-01-01

There are two isoforms of selenocysteine (Sec) tRNA[Ser]Sec that differ by a single methyl group, Um34. The non-Um34 isoform supports the synthesis of a subclass of selenoproteins, designated housekeeping, while the Um34 isoform supports the expression of another subclass, designated stress-related selenoproteins. Herein, we investigated the relationship between tRNA[Ser]Sec aminoacylation and Um34 synthesis which is the last step in the maturation of this tRNA. Mutation of the discriminator base at position 73 in tRNA[Ser]Sec dramatically reduced aminoacylation with serine, as did an inhibitor of seryl-tRNA synthetase, SB-217452. Although both the mutation and the inhibitor prevented Um34 synthesis, neither precluded the synthesis of any other of the known base modifications on tRNA[Ser]Sec following microinjection and incubation of the mutant tRNA[Ser]Sec transcript, or the wild type transcript along with inhibitor, in Xenopus oocytes. The data demonstrate that Sec tRNA[Ser]Sec must be aminoacylated for Um34 addition. The fact that selenium is required for Um34 methylation suggests that Sec must be attached to its tRNA for Um34 methylation. This would explain why selenium is essential for the function of Um34 methylase and provides further insights into the hierarchy of selenoprotein expression. PMID:21624347

77 FR 16270 - Updated Aging Management Criteria for Reactor Vessel Internal Components of Pressurized Water...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-20

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0070] Updated Aging Management Criteria for Reactor Vessel Internal Components of Pressurized Water Reactors AGENCY: Nuclear Regulatory Commission. ACTION: Draft..., ``Updated Aging Management Criteria for PWR Reactor Vessel Internal Components.'' This draft LR-ISG revises...

77 FR 23513 - Updated Aging Management Criteria for Reactor Vessel Internal Components of Pressurized Water...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-19

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0070] Updated Aging Management Criteria for Reactor Vessel Internal Components of Pressurized Water Reactors AGENCY: Nuclear Regulatory Commission. ACTION: Draft...-ISG), LR-ISG-2011-04, ``Updated Aging Management Criteria for PWR Reactor Vessel Internal Components...

Proceedings: 2002 Workshop on Pressurized Water Reactor Elevated Feedwater Iron Transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2002-11-01

Some pressurized water reactor (PWR) stations have experienced difficulty with maintaining feedwater (FW) iron concentrations below recommended concentration on a regular basis. A workshop held on September 17-18 in Dana Point, California, addressed the challenge of elevated feedwater iron transport in PWRs.

75 FR 15752 - Sunshine Act Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-30

...)--191, Assessment of Debris Accumulation on Pressurized Water Reactor (PWR) Sump Performance (Public... Fuel Cycle Oversight Process Revisions (Public Meeting). (Contact: Michael Raddatz, 301-492-3108.) This..., Employee/Labor Relations and Work Life Branch, at 301-492-2230, TDD: 301-415-2100, or by e-mail at angela...

75 FR 18907 - Sunshine Federal Register Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-13

...)-191, Assessment of Debris Accumulation on Pressurized Water Reactor (PWR) Sump Performance (Public... Fuel Cycle Oversight Process Revisions (Public Meeting). (Contact: Michael Raddatz, 301-492-3108.) This... Bolduc, Chief, Employee/Labor Relations and Work Life Branch, at 301-492-2230, TDD: 301-415-2100, or by e...

Thermodynamics of Anharmonic Systems: Uncoupled Mode Approximations for Molecules

DOE PAGES

Li, Yi-Pei; Bell, Alexis T.; Head-Gordon, Martin

2016-05-26

The partition functions, heat capacities, entropies, and enthalpies of selected molecules were calculated using uncoupled mode (UM) approximations, where the full-dimensional potential energy surface for internal motions was modeled as a sum of independent one-dimensional potentials for each mode. The computational cost of such approaches scales the same with molecular size as standard harmonic oscillator vibrational analysis using harmonic frequencies (HO hf). To compute thermodynamic properties, a computational protocol for obtaining the energy levels of each mode was established. The accuracy of the UM approximation depends strongly on how the one-dimensional potentials of each modes are defined. If the potentialsmore » are determined by the energy as a function of displacement along each normal mode (UM-N), the accuracies of the calculated thermodynamic properties are not significantly improved versus the HO hf model. Significant improvements can be achieved by constructing potentials for internal rotations and vibrations using the energy surfaces along the torsional coordinates and the remaining vibrational normal modes, respectively (UM-VT). For hydrogen peroxide and its isotopologs at 300 K, UM-VT captures more than 70% of the partition functions on average. By con trast, the HO hf model and UM-N can capture no more than 50%. For a selected test set of C2 to C8 linear and branched alkanes and species with different moieties, the enthalpies calculated using the HO hf model, UM-N, and UM-VT are all quite accurate comparing with reference values though the RMS errors of the HO model and UM-N are slightly higher than UM-VT. However, the accuracies in entropy calculations differ significantly between these three models. For the same test set, the RMS error of the standard entropies calculated by UM-VT is 2.18 cal mol -1 K -1 at 1000 K. By contrast, the RMS error obtained using the HO model and UM-N are 6.42 and 5.73 cal mol -1 K -1, respectively. For a test set composed of nine alkanes ranging from C5 to C8, the heat capacities calculated with the UM-VT model agree with the experimental values to within a RMS error of 0.78 cal mol -1 K -1 , which is less than one-third of the RMS error of the HO hf (2.69 cal mol -1 K -1) and UM-N (2.41 cal mol -1 K -1) models.« less

STS-40 Exp. No. 192 urine monitoring system (UMS) on OV-102's middeck

NASA Technical Reports Server (NTRS)

1991-01-01

STS-40 Experiment No. 192, Fluid-Electrolyte Regulation During Space Flight, urine monitoring system (UMS) is set up on the middeck of Columbia, Orbiter Vehicle (OV) 102, at the side hatch. The UMS is attached to OV-102's waste collection system (WCS). The urine specimen tray with sample tubes appears to the right of the UMS equipment.

In vitro investigation of head and neck cancer stem cell proportions and their changes following X-ray irradiation as a function of HPV status.

PubMed

Reid, Paul; Wilson, Puthenparampil; Li, Yanrui; Marcu, Loredana G; Staudacher, Alexander H; Brown, Michael P; Bezak, Eva

2017-01-01

Some head and neck squamous cell carcinomas (HNSCC) have a distinct aetiology, which depends on the presence of oncogenic human papilloma virus (HPV). Also, HNSCC contains cancer stem cells (CSCs) that have greater radioresistance and capacity to change replication dynamics in response to irradiation compared to non-clonogenic cells. Since there is limited data on CSCs in HNSCC as a function of HPV status, better understanding of their radiobiology may enable improved treatment outcome. Baseline and post-irradiation changes in CSC proportions were investigated by flow cytometry in a HPV-negative (UM-SCC-1) and a HPV-positive (UM-SCC-47) HNSCC cell line, using fluorescent staining with CD44/ALDH markers. CSC proportions in both irradiated and unirradiated cultures were compared for the two cell lines at various times post-irradiation. To assess repopulation of CSCs, untreated cultures were depleted of CD44+/ALDH+ cells and re-cultured for 3 weeks before flow cytometry analysis. CSC proportions in untreated cell lines were 0.57% (UM-SCC-1) and 2.87% (UM-SCC-47). Untreated cell lines depleted of CD44+/ALDH+ repopulated this phenotype to a mean of 0.15% (UM-SCC-1) and 6.76% (UM-SCC-47). All UM-SCC-47 generations showed elevated CSC proportions after irradiation, with the most significant increase at 2 days post-irradiation. The highest elevation in UM-SCC-1 CSCs was observed at 1 day post-irradiation in the 2nd generation and at 3 days after irradiation in the 3rd generation. When measured after 10 days, only the 3rd generation of UM-SCC-1 showed elevated CSCs. CSC proportions in both cell lines were elevated after exposure and varied with time post irradiation. UM-SCC-47 displayed significant plasticity in repopulating the CSC phenotype in depleted cultures, which was not seen in UM-SCC-1.

Final Prep on SSME

NASA Image and Video Library

2005-10-25

Alvin Pittman Sr., lead electronics technician with Pratt & Whitney Rocketdyne, and Janine Cuevas, a mechanical technician with PWR, perform final preparations on the space shuttle main engine tested Oct. 25, 2005, at NASA's Stennis Space Center. It was the first main engine test since Hurricane Katrina hit the Gulf Coast on Aug. 29.

Final Prep on SSME

NASA Technical Reports Server (NTRS)

2005-01-01

Alvin Pittman Sr., lead electronics technician with Pratt & Whitney Rocketdyne, and Janine Cuevas, a mechanical technician with PWR, perform final preparations on the space shuttle main engine tested Oct. 25, 2005, at NASA's Stennis Space Center. It was the first main engine test since Hurricane Katrina hit the Gulf Coast on Aug. 29.

DEVELOPMENT OF WELDED SEAL FOR S3G REACTOR VESSEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rogers, J.W.

1958-01-01

The development program consisted of preliminary design, welding accessibility and feasibility, pressure and displacement cycling, theoretical analysis and life computation, photoelastic analysis, and comparison of PWR straight sample cycling. Design ''C'' of the three primary designs considered proved more satisfactory from a fatigue life standpoint. (W.D. M.)

76 FR 40937 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses Involving No...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-12

... Generator Water Level High-High'' instrument setpoint and associated allowable value. The proposed change is... [Pressurized-Water Reactor] PWR Operability Requirements and Actions for RCS Leakage Instrumentation''. Basis... monitor is the containment atmospheric gaseous radiation monitor. The monitoring of RCS leakage is not a...

76 FR 21917 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses Involving No...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-19

... SGTR accident. At normal operating pressures, leakage from primary water stress corrosion cracking... PWR [pressurized- water reactor] Operability Requirements and Actions for RCS Leakage Instrumentation... water inventory can be obtained. Therefore, it is concluded that the proposed changes do not involve a...

76 FR 1644 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses Involving No...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-11

... tubesheet in that region. At normal operating pressures, leakage from primary water stress corrosion... cause failure. The EDG reliability will thereby be potentially increased by reducing the stresses on the..., ``Bases for Plugging Degraded PWR [pressurized-water reactor] Steam Generator Tubes,'' margins against...

Spelling well Despite Developmental Language Disorder: What Makes It Possible?

ERIC Educational Resources Information Center

Rakhlin, Natalia; Cardoso-Martins, Cláudia; Kornilov, Sergey A.; Grigorenko, Elena L.

2013-01-01

The goal of the study was to investigate the overlap between developmental language disorder (DLD) and developmental dyslexia, identified through spelling difficulties (SD), in Russian-speaking children. In particular, we studied the role of phoneme awareness (PA), rapid automatized naming (RAN), pseudoword repetition (PWR), morphological (MA),…

Liquid level, void fraction, and superheated steam sensor for nuclear-reactor cores. [PWR; BWR

DOEpatents

Tokarz, R.D.

1981-10-27

This disclosure relates to an apparatus for monitoring the presence of coolant in liquid or mixed liquid and vapor, and superheated gaseous phases at one or more locations within an operating nuclear reactor core, such as pressurized water reactor or a boiling water reactor.

78 FR 44596 - Minor Boundary Revision at Yosemite National Park

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-24

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-YOSE-13178; PS.SPWLA0028.00.1] Minor Boundary Revision at Yosemite National Park AGENCY: National Park Service, Interior. ACTION: Notification of Boundary Revision. SUMMARY: The boundary of Yosemite National Park is modified to include 80 acres...

78 FR 4477 - Review of Safety Analysis Reports for Nuclear Power Plants, Introduction

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-22

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0268] Review of Safety Analysis Reports for Nuclear Power... Analysis Reports for Nuclear Power Plants: LWR Edition.'' The new subsection is the Standard Review Plan... Nuclear Power Plants: Integral Pressurized Water Reactor (iPWR) Edition.'' DATES: Comments must be filed...

77 FR 63343 - Biweekly Notice: Applications and Amendments to Facility Operating Licenses and Combined Licenses...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-16

... PWR [Pressurized-Water Reactor] Steam Generator Tubes'' (Reference 32) and [Nuclear Energy Institute... maintains the required structural margins of the SG tubes for both normal and accident conditions. Nuclear Energy Institute 97-06, ``Steam Generator Program Guidelines'' (Reference 8), and NRC Regulatory Guide 1...

Counterfeit Parts Prevention Strategy Guide Product Overview

DTIC Science & Technology

2014-05-08

pwr.utc.com Mark King Micopac markking@micropac.com Andrew King Boeing andrew.m.king@boeing.com Byron Knight NRO knightby@nro.mil Hans Koenigsmann SpaceX ...Marvin VanderWeg SpaceX marvin.vanderwag@spacex.com Gerrit VanOmmering SSL gerrit.vanommering@sslmda.com Michael Verzuh Ball mverzuh@ball.com John Vilja

In-situ Condition Monitoring of Components in Small Modular Reactors Using Process and Electrical Signature Analysis. Final report, volume 1. Development of experimental flow control loop, data analysis and plant monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upadhyaya, Belle; Hines, J. Wesley; Damiano, Brian

The research and development under this project was focused on the following three major objectives: Objective 1: Identification of critical in-vessel SMR components for remote monitoring and development of their low-order dynamic models, along with a simulation model of an integral pressurized water reactor (iPWR). Objective 2: Development of an experimental flow control loop with motor-driven valves and pumps, incorporating data acquisition and on-line monitoring interface. Objective 3: Development of stationary and transient signal processing methods for electrical signatures, machinery vibration, and for characterizing process variables for equipment monitoring. This objective includes the development of a data analysis toolbox. Themore » following is a summary of the technical accomplishments under this project: - A detailed literature review of various SMR types and electrical signature analysis of motor-driven systems was completed. A bibliography of literature is provided at the end of this report. Assistance was provided by ORNL in identifying some key references. - A review of literature on pump-motor modeling and digital signal processing methods was performed. - An existing flow control loop was upgraded with new instrumentation, data acquisition hardware and software. The upgrading of the experimental loop included the installation of a new submersible pump driven by a three-phase induction motor. All the sensors were calibrated before full-scale experimental runs were performed. - MATLAB-Simulink model of a three-phase induction motor and pump system was completed. The model was used to simulate normal operation and fault conditions in the motor-pump system, and to identify changes in the electrical signatures. - A simulation model of an integral PWR (iPWR) was updated and the MATLAB-Simulink model was validated for known transients. The pump-motor model was interfaced with the iPWR model for testing the impact of primary flow perturbations (upsets) on plant parameters and the pump electrical signatures. Additionally, the reactor simulation is being used to generate normal operation data and data with instrumentation faults and process anomalies. A frequency controller was interfaced with the motor power supply in order to vary the electrical supply frequency. The experimental flow control loop was used to generate operational data under varying motor performance characteristics. Coolant leakage events were simulated by varying the bypass loop flow rate. The accuracy of motor power calculation was improved by incorporating the power factor, computed from motor current and voltage in each phase of the induction motor.- A variety of experimental runs were made for steady-state and transient pump operating conditions. Process, vibration, and electrical signatures were measured using a submersible pump with variable supply frequency. High correlation was seen between motor current and pump discharge pressure signal; similar high correlation was exhibited between pump motor power and flow rate. Wide-band analysis indicated high coherence (in the frequency domain) between motor current and vibration signals. - Wide-band operational data from a PWR were acquired from AMS Corporation and used to develop time-series models, and to estimate signal spectrum and sensor time constant. All the data were from different pressure transmitters in the system, including primary and secondary loops. These signals were pre-processed using the wavelet transform for filtering both low-frequency and high-frequency bands. This technique of signal pre-processing provides minimum distortion of the data, and results in a more optimal estimation of time constants of plant sensors using time-series modeling techniques.« less

Study of factors affecting growth and cold acclimation of Vitis callus cultures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, L.

1987-01-01

In vitro grape tissue culture initiation, growth, and cold acclimation were studied. Factors involved were genotypes, media, plant growth regulators, age, light, temperature, antioxidant, clearing and adsorbing agents, sucrose level, osmotic potential, ABA, chilling and freezing treatments. Murashige and Skoog (MS) medium containing 1 ..mu..M 2,4-d + 0.1 uM Ba, MS containing 1 uM 2,4-D, and woody plant medium containing 1 uM 2,4-D + 0.1 uM BA produced abundant callus tissue for most grape genotypes; either WPM or MS containing 1 uM BA stimulated shoot growth in all the 12 genotypes tested. Adding 1 uM abscisic acid (ABA) to themore » B5 medium with 1 uM 2,4-D and 0.5 uM BA enhanced growth and quality of Chancellor callus. /sup 3/H-ABA was taken up actively by callus tissue at 12 days after subculture, but by 20 d this effect disappeared. When /sup 14/C-sucrose was added to the medium. /sup 14/C level of cells reached a plateau after 48 h; this plateau was higher if ABA was also present in the medium. Cells on media containing ABA were larger in size, lighter in color, and more loosely connected.« less

Three-frequency Nd:YAG laser for dental treatment

NASA Astrophysics Data System (ADS)

Kadlecová, Martina; Dostálová, Tat'jana; Jelínková, Helena; Němec, Michal; Å ulc, Jan; Fibrich, Martin; Bradna, Pavel; Nejezchleb, Karel; Kapitch, Nickalai; Å koda, Václav

2018-02-01

In the last decade, lasers found a number of indications in dentistry. However, there is still one problem: the narrow spectrum of usefulness for individual radiation wavelengths. The aim of our study is to demonstrate the use of a compact three-frequency pulsed Nd-YAG laser for more than one treatment, namely disinfection, coagulation, selective ablation, and soft tissue removal. The laser wavelengths and the maximal energies achieved were the following: 1.06 um, 1.32 um, 1.44 um and 830 mJ, 425 mJ, and 200 mJ, respectively. It has been found that all of the investigated wavelengths exhibit disinfection properties. Moreover, radiation of 1.06 um wavelength removes soft tissue and exhibits also coagulation properties. Radiation of 1.44 um is most useful for selective ablation of initial caries and disinfection, and 1.32 um radiation can be used for precise ablation when higher energy is applied.

Recovery Act: Novel Kerf-Free PV Wafering that provides a low-cost approach to generate wafers from 150um to 50um in thickness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fong, Theodore E.

2013-05-06

The technical paper summarizes the project work conducted in the development of Kerf-Free silicon wafering equipment for silicon solar wafering. This new PolyMax technology uses a two step process of implantation and cleaving to exfoliate 50um to 120um wafers with thicknesses ranging from 50um to 120um from a 125mm or 156mm pseudo-squared silicon ingot. No kerf is generated using this method of wafering. This method of wafering contrasts with the current method of making silicon solar wafers using the industry standard wire saw equipment. The report summarizes the activity conducted by Silicon Genesis Corporation in working to develop this technologymore » further and to define the roadmap specifications for the first commercial proto-type equipment for high volume solar wafer manufacturing using the PolyMax technology.« less

Towards reducing the impacts of unwanted movements on identification of motion intentions.

PubMed

Li, Xiangxin; Chen, Shixiong; Zhang, Haoshi; Samuel, Oluwarotimi Williams; Wang, Hui; Fang, Peng; Zhang, Xiufeng; Li, Guanglin

2016-06-01

Surface electromyogram (sEMG) has been extensively used as a control signal in prosthesis devices. However, it is still a great challenge to make multifunctional myoelectric prostheses clinically available due to a number of critical issues associated with existing EMG based control strategy. One such issue would be the effect of unwanted movements (UMs) that are inadvertently done by users on the performance of movement classification in EMG pattern recognition based algorithms. Since UMs are not considered in training a classifier, they would decay the performance of a trained classifier in identifying the target movements (TMs), which would cause some undesired actions in control of multifunctional prostheses. In this study, the impact of UMs was systemically investigated in both able-bodied subjects and transradial amputees. Our results showed that the UMs would be unevenly classified into all classes of the TMs. To reduce the impact of the UMs on the performance of a classifier, a new training strategy that would categorize all possible UMs into a new movement class was proposed and a metric called Reject Ratio that is a measure of how many UMs is rejected by a trained classifier was adopted. The results showed that the average Reject Ratio across all the participants was greater than 91%, meanwhile the average classification accuracy of TMs was above 99% when UMs occurred. This suggests that the proposed training strategy could greatly reduce the impact of UMs on the performance of the trained classifier in identifying the TMs and may enhance the robustness of myoelectric control in clinical applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Histone deacetylase inhibitors induce growth arrest and differentiation in uveal melanoma

PubMed Central

Landreville, Solange; Agapova, Olga A.; Matatall, Katie A.; Kneass, Zachary T.; Onken, Michael D.; Lee, Ryan S.; Bowcock, Anne M.; Harbour, J. William

2011-01-01

Purpose Metastasis is responsible for the death of most cancer patients, yet few therapeutic agents are available which specifically target the molecular events that lead to metastasis. We recently showed that inactivating mutations in the tumor suppressor gene BAP1 are closely associated with loss of melanocytic differentiation in uveal melanoma and metastasis (UM). The purpose of this study was to identify therapeutic agents that reverse the phenotypic effects of BAP1 loss in UM. Experimental Design In silico screens were performed to identify therapeutic compounds predicted to differentiate UM cells using Gene Set Enrichment Analysis and Connectivity Map databases. Valproic acid, trichostatin A, LBH-589 and suberoylanilide hydroxamic acid were evaluated for their effects on UM cells using morphologic evaluation, MTS viability assays, BrdU incorporation, flow cytometry, clonogenic assays, gene expression profiling, histone acetylation and ubiquitination assays, and a murine xenograft tumorigenicity model. Results HDAC inhibitors induced morphologic differentiation, cell cycle exit, and a shift to a differentiated, melanocytic gene expression profile in cultured UM cells. Valproic acid inhibited the growth of UM tumors in vivo. Conclusions These findings suggest that HDAC inhibitors may have therapeutic potential for inducing differentiation and prolonged dormancy of micrometastatic disease in UM. PMID:22038994

77 FR 60479 - Burnup Credit in the Criticality Safety Analyses of Pressurized Water Reactor Spent Fuel in...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-03

... Pressurized Water Reactor Spent Fuel in Transportation and Storage Casks AGENCY: Nuclear Regulatory Commission... 3, entitled, ``Burnup Credit in the Criticality Safety Analyses of PWR [Pressurized Water Reactor... water reactor spent nuclear fuel (SNF) in transportation packages and storage casks. SFST-ISG-8...

76 FR 79708 - Draft Environmental Impact Statement/General Management Plan, Golden Gate National Recreation...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-22

...). The Plan/DEIS evaluates four alternatives for updating the current approach to management in Golden.... In recognition of the complexity of the proposed plan alternatives, and with deference to interest... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-PWRO-1108-8862; 2031-A038-409] Draft...

78 FR 33120 - Final Interim Staff Guidance LR-ISG-2011-04; Updated Aging Management Criteria for Reactor Vessel...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-03

..., ``Generic Aging Lessons Learned Report'' (GALL Report), for the aging management of Pressurized Water... communicate insights and lessons learned and to address emergent issues not covered in license renewal... ensure that PWR license renewal applicants will adequately address age-related degradation and aging...

LOFT. Reactor arrives at containment building (TAN650), now being pushed ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LOFT. Reactor arrives at containment building (TAN-650), now being pushed by locomotive. Camera facing northerly. Note "Hello Dolly" and "PWR MTA No. 1" (pressurized water reactor mobile test assembly) signs. Date: 1973. INEEL negative no. 73-3710 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

40 CFR 59.505 - How do I demonstrate compliance with the reactivity limits?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL VOLATILE ORGANIC COMPOUND EMISSION STANDARDS FOR CONSUMER AND COMMERCIAL PRODUCTS National Volatile Organic Compound Emission Standards for Aerosol Coatings § 59.505 How..., 2B, or 2C. WFi = weight fraction of component i in the product, (2) Calculate the PWR of each product...

40 CFR 59.505 - How do I demonstrate compliance with the reactivity limits?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL VOLATILE ORGANIC COMPOUND EMISSION STANDARDS FOR CONSUMER AND COMMERCIAL PRODUCTS National Volatile Organic Compound Emission Standards for Aerosol Coatings § 59.505 How..., 2B, or 2C. WFi = weight fraction of component i in the product, (2) Calculate the PWR of each product...

40 CFR 59.505 - How do I demonstrate compliance with the reactivity limits?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL VOLATILE ORGANIC COMPOUND EMISSION STANDARDS FOR CONSUMER AND COMMERCIAL PRODUCTS National Volatile Organic Compound Emission Standards for Aerosol Coatings § 59.505 How..., 2B, or 2C. WFi = weight fraction of component i in the product, (2) Calculate the PWR of each product...

75 FR 13800 - Sunshine Federal Register Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-23

..., Assessment of Debris Accumulation on Pressurized Water Reactor (PWR) Sump Performance (Public Meeting..., 2010. Week of April 26, 2010--Tentative Thursday, April 29, 2010 9:30 a.m. Briefing on the Fuel Cycle... and Work Life Branch, at 301-492-2230, TDD: 301-415-2100, or by e-mail at [email protected

77 FR 65906 - Minor Boundary Revision at Minidoka National Historic Site

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-31

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-MIIN-11234; 9360-726] Minor Boundary Revision at Minidoka National Historic Site AGENCY: National Park Service, Interior. ACTION: Notification of boundary revision. SUMMARY: Notice is hereby given that, pursuant to 16 U.S.C. 460l- 9(c)(1)(ii...

78 FR 64027 - Preoperational Testing of Emergency Core Cooling Systems for Pressurized-Water Reactors

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-25

...The U.S. Nuclear Regulatory Commission (NRC) is issuing a revision to regulatory guide (RG), 1.79, ``Preoperational Testing of Emergency Core Cooling Systems for Pressurized-Water Reactors.'' This RG is being revised to incorporate guidance for preoperational testing of new pressurized water reactor (PWR) designs.

76 FR 24514 - Honouliuli Special Resource Study, Honolulu, Maui, Hawaii, and Kauai Counties, HI

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-02

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-PWRO-0308-6923;9082-HONO-420] Honouliuli.... Background: As authorized by the Department of the Interior, Environment, and Related Agencies Appropriations... State of Hawaii with respect to (1) Their significance as components of World War II; (2) significance...

76 FR 22917 - Dog Management Plan/Draft Environmental Impact Statement, Golden Gate National Recreation Area...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-PWRO--0315-696; 8145-8B90-SZM] Dog... Impact Statement/Dog Management Plan, Golden Gate National Recreation Area. SUMMARY: The National Park Service has prepared a Draft Dog Management Plan and Environmental Impact Statement (Plan/DEIS). The Plan...

Amorphous and Nanocrystalline High Temperature Magnetic Material for PWR

DTIC Science & Technology

2006-03-01

FOR PUBLICATION. //Signature// //Signature// ______________________________________ __________________________________ JOHN C ...times that of conventional ferrites at room temperature); 2) Frequency: 200 kHz to 1 MHz; 3) Temperature: 200 ° C and above. The goals of the DUST...NAME OF RESPONSIBLE PERSON (Monitor) a. REPORT Unclassified b. ABSTRACT Unclassified c . THIS PAGE Unclassified 17. LIMITATION OF ABSTRACT

Mixed Legendre moments and discrete scattering cross sections for anisotropy representation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calloo, A.; Vidal, J. F.; Le Tellier, R.

2012-07-01

This paper deals with the resolution of the integro-differential form of the Boltzmann transport equation for neutron transport in nuclear reactors. In multigroup theory, deterministic codes use transfer cross sections which are expanded on Legendre polynomials. This modelling leads to negative values of the transfer cross section for certain scattering angles, and hence, the multigroup scattering source term is wrongly computed. The first part compares the convergence of 'Legendre-expanded' cross sections with respect to the order used with the method of characteristics (MOC) for Pressurised Water Reactor (PWR) type cells. Furthermore, the cross section is developed using piecewise-constant functions, whichmore » better models the multigroup transfer cross section and prevents the occurrence of any negative value for it. The second part focuses on the method of solving the transport equation with the above-mentioned piecewise-constant cross sections for lattice calculations for PWR cells. This expansion thereby constitutes a 'reference' method to compare the conventional Legendre expansion to, and to determine its pertinence when applied to reactor physics calculations. (authors)« less

Linking Grain Boundary Microstructure to Stress Corrosion Cracking of Cold Rolled Alloy 690 in PWR Primary Water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruemmer, Stephen M.; Olszta, Matthew J.; Toloczko, Mychailo B.

2012-10-01

Grain boundary microstructures and microchemistries are examined in cold-rolled alloy 690 tubing and plate materials and comparisons are made to intergranular stress corrosion cracking (IGSCC) behavior in PWR primary water. Chromium carbide precipitation is found to be a key aspect for materials in both the mill annealed and thermally treated conditions. Cold rolling to high levels of reduction was discovered to produce small IG voids and cracked carbides in alloys with a high density of grain boundary carbides. The degree of permanent grain boundary damage from cold rolling was found to depend directly on the initial IG carbide distribution. Formore » the same degree of cold rolling, alloys with few IG precipitates exhibited much less permanent damage. Although this difference in grain boundary damage appears to correlate with measured SCC growth rates, crack tip examinations reveal that cracked carbides appeared to blunt propagation of IGSCC cracks in many cases. Preliminary results suggest that the localized grain boundary strains and stresses produced during cold rolling promote IGSCC susceptibility and not the cracked carbides and voids.« less

Neutron-gamma flux and dose calculations in a Pressurized Water Reactor (PWR)

NASA Astrophysics Data System (ADS)

Brovchenko, Mariya; Dechenaux, Benjamin; Burn, Kenneth W.; Console Camprini, Patrizio; Duhamel, Isabelle; Peron, Arthur

2017-09-01

The present work deals with Monte Carlo simulations, aiming to determine the neutron and gamma responses outside the vessel and in the basemat of a Pressurized Water Reactor (PWR). The model is based on the Tihange-I Belgian nuclear reactor. With a large set of information and measurements available, this reactor has the advantage to be easily modelled and allows validation based on the experimental measurements. Power distribution calculations were therefore performed with the MCNP code at IRSN and compared to the available in-core measurements. Results showed a good agreement between calculated and measured values over the whole core. In this paper, the methods and hypotheses used for the particle transport simulation from the fission distribution in the core to the detectors outside the vessel of the reactor are also summarized. The results of the simulations are presented including the neutron and gamma doses and flux energy spectra. MCNP6 computational results comparing JEFF3.1 and ENDF-B/VII.1 nuclear data evaluations and sensitivity of the results to some model parameters are presented.

On the Solidification and Structure Formation during Casting of Large Inserts in Ferritic Nodular Cast Iron

NASA Astrophysics Data System (ADS)

Tadesse, Abel; Fredriksson, Hasse

2018-06-01

The graphite nodule count and size distributions for boiling water reactor (BWR) and pressurized water reactor (PWR) inserts were investigated by taking samples at heights of 2160 and 1150 mm, respectively. In each cross section, two locations were taken into consideration for both the microstructural and solidification modeling. The numerical solidification modeling was performed in a two-dimensional model by considering the nucleation and growth in eutectic ductile cast iron. The microstructural results reveal that the nodule size and count distribution along the cross sections are different in each location for both inserts. Finer graphite nodules appear in the thinner sections and close to the mold walls. The coarser nodules are distributed mostly in the last solidified location. The simulation result indicates that the finer nodules are related to a higher cooling rate and a lower degree of microsegregation, whereas the coarser nodules are related to a lower cooling rate and a higher degree of microsegregation. The solidification time interval and the last solidifying locations in the BWR and PWR are also different.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Overman, Nicole R.; Toloczko, Mychailo B.; Olszta, Matthew J.

High chromium, nickel-base Alloy 690 exhibits an increased resistance to stress corrosion cracking (SCC) in pressurized water reactor (PWR) primary water environments over lower chromium alloy 600. As a result, Alloy 690 has been used to replace Alloy 600 for steam generator tubing, reactor pressure vessel nozzles and other pressure boundary components. However, recent laboratory crack-growth testing has revealed that heavily cold-worked Alloy 690 materials can become susceptible to SCC. To evaluate reasons for this increased SCC susceptibility, detailed characterizations have been performed on as-received and cold-worked Alloy 690 materials using electron backscatter diffraction (EBSD) and Vickers hardness measurements. Examinationsmore » were performed on cross sections of compact tension specimens that were used for SCC crack growth rate testing in simulated PWR primary water. Hardness and the EBSD integrated misorientation density could both be related to the degree of cold work for materials of similar grain size. However, a microstructural dependence was observed for strain correlations using EBSD and hardness which should be considered if this technique is to be used for gaining insight on SCC growth rates« less

Management of thermal peaking factors in CONFU-B PWR assemblies using neutron poisons and tailored enrichment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Visosky, M.; Hejzlar, P.; Kazimi, M.

2006-07-01

CONFU-B assemblies are PWR assemblies containing standard Uranium fuel rods and TRU bearing inert material fuel rods and are designed to achieve net TRU destruction over a 4.5-year irradiation. These highly heterogeneous assemblies tend to exhibit large intra-assembly power peaking factors (IAPPF). Neutronic strategies to reduce IAPPF are developed. The IAPPF are calculated at the assembly level using CASMO4, and these are used to calculate the most restrictive thermal margin (the Minimum Departure from Nucleate Boiling Ratio, MDNBR) using a whole-core VIPRE-01 model. This paper examines two strategies to manage the thermal margin of a CONFU-B assembly while retaining themore » TRU destruction performance: use of neutron poisons and tailored enrichment schemes. Burnable poisons can be used to suppress BOL reactivity of fresh CONFU-B assemblies with only minor impact on MDNBR and TRU destruction performance. Tailored enrichment, along with the use of soluble boron, can achieve significant improvements in MDNBR, but at some cost to TRU destruction performance. (authors)« less

Risk-Informed External Hazards Analysis for Seismic and Flooding Phenomena for a Generic PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parisi, Carlo; Prescott, Steve; Ma, Zhegang

This report describes the activities performed during the FY2017 for the US-DOE Light Water Reactor Sustainability Risk-Informed Safety Margin Characterization (LWRS-RISMC), Industry Application #2. The scope of Industry Application #2 is to deliver a risk-informed external hazards safety analysis for a representative nuclear power plant. Following the advancements occurred during the previous FYs (toolkits identification, models development), FY2017 focused on: increasing the level of realism of the analysis; improving the tools and the coupling methodologies. In particular the following objectives were achieved: calculation of buildings pounding and their effects on components seismic fragility; development of a SAPHIRE code PRA modelsmore » for 3-loops Westinghouse PWR; set-up of a methodology for performing static-dynamic PRA coupling between SAPHIRE and EMRALD codes; coupling RELAP5-3D/RAVEN for performing Best-Estimate Plus Uncertainty analysis and automatic limit surface search; and execute sample calculations for demonstrating the capabilities of the toolkit in performing a risk-informed external hazards safety analyses.« less

Probability of in-vessel steam explosion-induced containment failure for a KWU PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Esmaili, H.; Khatib-Rahbar, M.; Zuchuat, O.

During postulated core meltdown accidents in light water reactors, there is a likelihood for an in-vessel steam explosion when the melt contacts the coolant in the lower plenum. The objective of the work described in this paper is to determine the conditional probability of in-vessel steam explosion-induced containment failure for a Kraftwerk Union (KWU) pressurized water reactor (PWR). The energetics of the explosion depends on the mass of the molten fuel that mixes with the coolant and participates in the explosion and on the conversion of fuel thermal energy into mechanical work. The work can result in the generation ofmore » dynamic pressures that affect the lower head (and possibly lead to its failure), and it can cause acceleration of a slug (fuel and coolant material) upward that can affect the upper internal structures and vessel head and ultimately cause the failure of the upper head. If the upper head missile has sufficient energy, it can reach the containment shell and penetrate it. The analysis, must therefore, take into account all possible dissipation mechanisms.« less

Mathematisches Bewusstsein

NASA Astrophysics Data System (ADS)

Kaenders, Rainer; Kvasz, Ladislav

Wenn jemand sagt, dass ein Bus um 9 Uhr abfährt - weiß man es dann? Angenommen, man ist darüber unterrichtet, dass die Busse unter der Woche immer zur vollen Stunde abfahren - von 7 Uhr morgens bis 7 Uhr abends, weiß man es dann mit dem Wissen um diese allgemeine Regel besser, dass der Bus um 9 Uhr abfährt? Macht es einen Unterschied, ob man den Fahrplan erstellt, den Bus lenkt oder nur mitfährt, um sich dieser Tatsache bewusst zu sein?

VizieR Online Data Catalog: YSOs in California Molecular Cloud (Lada+, 2017)

NASA Astrophysics Data System (ADS)

Lada, C. J.; Lewis, J. A.; Lombardi, M.; Alves, J.

2018-01-01

The CMC was observed by the all-sky Planck observatory and by the Herschel Space Observatory as part of the "Auriga-California" program (Harvey et al. 2013, Cat J/ApJ/764/133). The Herschel data we used consisted of observations obtained in parallel mode simultaneously using the PACS and SPIRE instruments. For the purposes of this study we use Herschel observations made in the PACS 160um band, and the SPIRE 250um, 350um and 500um bands. (1 data file).

An ethical leadership program for nursing unit managers.

PubMed

Jeon, Sang Hee; Park, Mihyun; Choi, Kyungok; Kim, Mi Kyoung

2018-03-01

The aims of this study were to evaluate the effect of an ethical leadership program (ELP) on ethical leadership, organizational citizenship behavior (OCB), and job outcomes of nursing unit managers (UMs) and to examine changes in staff nurses' perception about UMs' EL, OCB, job outcomes, and ethical work environments (EWEs) post-ELP. A quasi-experimental (pre- and post-test design) study conducted six-month intervention (ELP) using self-reported UM survey (n=44), and staff nurses (n=158) were randomly extracted by two steps. The Korean version of Ethical Leadership at Work for UMs' self-ethical leadership, the Ethical Leadership Scale for staff nurses' perceived ethical leadership, a 19-item OCB scale, and six dimensions of the medium-sized Copenhagen Psychosocial Questionnaire II for job outcomes and EWEs were administered at baseline and post-intervention. UMs' ethical leadership scores differed significantly over time in people orientation (p=0.041) and concern for ethical leadership sustainability (p=0.002) adjusting for UM experience duration and nursing unit type. Total mean and level of power-sharing of ethical leadership among UMs with <5years of UM experience improved significantly over time. Of staff nurses' perception changes about UMs' ethical leadership, OCB, job outcomes, and EWEs, significant improvement over time appeared only in EWEs' work influence level (p=0.007). This study provides useful information for clinical ELP development and examining the program's effect on leadership skills and followers' outcomes. Program facilitation relies on practical training methods, participant motivation, and assessment outcome designs by controlling clinical confounding factors. Findings have implications as an attempt for intervention to promote competencies related to ethical leadership of nursing unit managers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Transport and mixing of a volume of fluid in a complex geometry

NASA Astrophysics Data System (ADS)

Gavelli, Filippo

This work presents the results of the experimental investigation of an entire sequence of events, leading to an unwanted injection of boron-depleted water into the core of a PWR. The study is subdivided into three tasks: the generation of a dilute volume in the primary system, its transport to the core, and the mixing encountered along the path. Experiments conducted at the University of Maryland (UM) facility show that, during a Small-Break LOCA transient, volumes of dilute coolant are segregated in the system, by means of phase-separating energy transport from the core to the steam generators (Boiler Condenser Mode). Two motion-initiating mechanisms are considered: the resumption of natural circulation during the recovery of the primary liquid inventory, and the reactor coolant pump startup under BCM conditions. During the inventory recovery, various phenomena are observed, that contribute to the mixing of the dilute volumes prior to the resumption of flow. The pump activation, instead, occurs in a stagnant system, therefore, no mixing of the unborated liquid has occurred. Since an unmixed slug has the potential for a larger reactivity excursion than a partially mixed one, the pump-initiated flow resumption represents the worst-case scenario. The impulse - response method is applied, for the first time, to the problem of mixing in the downcomer. This allows to express the mixing in terms of two parameters, the dispersion number and the residence time, characteristics of the flow distribution in the complex annular geometry. Other important results are obtained from the analysis of the experimental data with this procedure. It is shown that the turbulence generated by the pump impeller has a significant impact on the overall mixing. Also, the geometric discontinuities in the downcomer (in particular, the gap enlargement below the cold leg elevation) are shown to be the cause of vortex structures that highly enhance the mixing process.

Laminar flow assisted anisotropic bacteria absorption for chemotaxis delivery of bacteria-attached microparticle

NASA Astrophysics Data System (ADS)

Huh, Keon; Oh, Darong; Son, Seok Young; Yoo, Hyung Jung; Song, Byeonghwa; Cho, Dong-il Dan; Seo, Jong-Mo; Kim, Sung Jae

2016-12-01

The concepts of microrobots has been drawn significant attentions recently since its unprecedented applicability in nanotechnology and biomedical field. Bacteria attached microparticles presented in this work are one of pioneering microrobot technology for self-propulsion or producing kinetic energy from ambient for their motions. Microfluidic device, especially utilizing laminar flow characteristics, were employed for anisotropic attachment of Salmonella typhimurium flagellated chemotactic bacteria to 30 um × 30 um and 50 um × 50 um microparticles that made of biodegradable polymer. Any toxic chemicals or harmful treatments were excluded during the attachment process and it finished within 100 s for the anisotropic attachment. The attachments were directly confirmed by fluorescent intensity changes and SEM visualization. Chemotaxis motions were tracked using aspartate and the maximum velocity of the bacteria-attached microrobot was measured to be 5 um/s which is comparable to prior state of art technologies. This reusable and scalable method could play a key role in chemotaxis delivery of functional microparticles such as drug delivery system.

PWR-related integral safety experiments in the PKL 111 test facility SBLOCA under beyond-design-basis accident conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weber, P.; Umminger, K.J.; Schoen, B.

1995-09-01

The thermal hydraulic behavior of a PWR during beyond-design-basis accident scenarios is of vital interest for the verification and optimization of accident management procedures. Within the scope of the German reactor safety research program experiments were performed in the volumetrically scaled PKL 111 test facility by Siemens/KWU. This highly instrumented test rig simulates a KWU-design PWR (1300 MWe). In particular, the latest tests performed related to a SBLOCA with additional system failures, e.g. nitrogen entering the primary system. In the case of a SBLOCA, it is the goal of the operator to put the plant in a condition where themore » decay heat can be removed first using the low pressure emergency core cooling system and then the residual heat removal system. The experimental investigation presented assumed the following beyond-design-basis accident conditions: 0.5% break in a cold leg, 2 of 4 steam generators (SGs) isolated on the secondary side (feedwater- and steam line-valves closed), filled with steam on the primary side, cooldown of the primary system using the remaining two steam generators, high pressure injection system only in the two loops with intact steam generators, if possible no operator actions to reach the conditions for residual heat removal system activation. Furthermore, it was postulated that 2 of the 4 hot leg accumulators had a reduced initial water inventory (increased nitrogen inventory), allowing nitrogen to enter the primary system at a pressure of 15 bar and nearly preventing the heat transfer in the SGs ({open_quotes}passivating{close_quotes} U-tubes). Due to this the heat transfer regime in the intact steam generators changed remarkably. The primary system showed self-regulating system effects and heat transfer improved again (reflux-condenser mode in the U-tube inlet region).« less

Characterization of carbon-14 generated by the nuclear power industry. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eabry, S.; Vance, J.N.; Cline, J.E.

1995-11-01

This report describes an evaluation of C-14 production rates in light-water reactors (LWRs) and characterization of its chemical speciation and environmental behavior. The study estimated the total production rate of the nuclide in operating PWRs and BWRs along with the assessment of the C-14 content of solid radwaste. The major source of production of C-14 in both PWR`s and BWRs was the activation of 0-17 in the water molecule and of N-14 dissolved in reactor coolant. The production of C-14 was estimated to range from 7 Ci/GW(e)-year to 11 Ci/GW(e)-year. The estimated range of the quantity of C-14 in LLWmore » was 1-2 Ci/ reactor-year which compares favorably with data obtained from shipping manifests. The environmental behavior of C-14 associated with low-level waste (LLW) disposal is greatly dependent upon its chemical speciation. This scoping study was performed to help identify the occurrence of inorganic and organic forms of C-14 in reactor coolant water and in primary coolant demineralization resins. These represent the major source for C-14 in LLW from nuclear power stations. Also, the behavior of inorganic and two of the organic forms of C-14 on soil uptake was determined by measuring distribution coefficients (Kd`s) on two soil types and a cement, using two different groundwater types. This study confirms that C-14 concentrations are significantly higher in the primary coolant from PWR stations compared to BWR stations. The C-14 followed trends of Co-60 generation during primary coolant demineralization at all but one of the stations examined. However, the C-14/Co-60 activity ratios measured by this study in resin samples through which samples of coolant were drawn were about 8 to 42 times higher than those reported for waste samples in the industry data base for PWR stations, and 15 to 730 times lower for the BWR stations.« less

Bias estimates used in lieu of validation of fission products and minor actinides in MCNP K eff calculations for PWR burnup credit casks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mueller, Don E.; Marshall, William J.; Wagner, John C.

The U.S. Nuclear Regulatory Commission (NRC) Division of Spent Fuel Storage and Transportation recently issued Interim Staff Guidance (ISG) 8, Revision 3. This ISG provides guidance for burnup credit (BUC) analyses supporting transport and storage of PWR pressurized water reactor (PWR) fuel in casks. Revision 3 includes guidance for addressing validation of criticality (k eff) calculations crediting the presence of a limited set of fission products and minor actinides (FP&MA). Based on previous work documented in NUREG/CR-7109, recommendation 4 of ISG-8, Rev. 3, includes a recommendation to use 1.5 or 3% of the FP&MA worth to conservatively cover the biasmore » due to the specified FP&MAs. This bias is supplementary to the bias and bias uncertainty resulting from validation of k eff calculations for the major actinides in SNF and does not address extension to actinides and fission products beyond those identified herein. The work described in this report involves comparison of FP&MA worths calculated using SCALE and MCNP with ENDF/B-V, -VI, and -VII based nuclear data and supports use of the 1.5% FP&MA worth bias when either SCALE or MCNP codes are used for criticality calculations, provided the other conditions of the recommendation 4 are met. The method used in this report may also be applied to demonstrate the applicability of the 1.5% FP&MA worth bias to other codes using ENDF/B V, VI or VII based nuclear data. The method involves use of the applicant s computational method to generate FP&MA worths for a reference SNF cask model using specified spent fuel compositions. The applicant s FP&MA worths are then compared to reference values provided in this report. The applicants FP&MA worths should not exceed the reference results by more than 1.5% of the reference FP&MA worths.« less

Subsurface Hybrid Power Options for Oil & Gas Production at Deep Ocean Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, J C; Haut, R; Jahn, G

2010-02-19

An investment in deep-sea (deep-ocean) hybrid power systems may enable certain off-shore oil and gas exploration and production. Advanced deep-ocean drilling and production operations, locally powered, may provide commercial access to oil and gas reserves otherwise inaccessible. Further, subsea generation of electrical power has the potential of featuring a low carbon output resulting in improved environmental conditions. Such technology therefore, enhances the energy security of the United States in a green and environmentally friendly manner. The objective of this study is to evaluate alternatives and recommend equipment to develop into hybrid energy conversion and storage systems for deep ocean operations.more » Such power systems will be located on the ocean floor and will be used to power offshore oil and gas exploration and production operations. Such power systems will be located on the oceans floor, and will be used to supply oil and gas exploration activities, as well as drilling operations required to harvest petroleum reserves. The following conceptual hybrid systems have been identified as candidates for powering sub-surface oil and gas production operations: (1) PWR = Pressurized-Water Nuclear Reactor + Lead-Acid Battery; (2) FC1 = Line for Surface O{sub 2} + Well Head Gas + Reformer + PEMFC + Lead-Acid & Li-Ion Batteries; (3) FC2 = Stored O2 + Well Head Gas + Reformer + Fuel Cell + Lead-Acid & Li-Ion Batteries; (4) SV1 = Submersible Vehicle + Stored O{sub 2} + Fuel Cell + Lead-Acid & Li-Ion Batteries; (5) SV2 = Submersible Vehicle + Stored O{sub 2} + Engine or Turbine + Lead-Acid & Li-Ion Batteries; (6) SV3 = Submersible Vehicle + Charge at Docking Station + ZEBRA & Li-Ion Batteries; (7) PWR TEG = PWR + Thermoelectric Generator + Lead-Acid Battery; (8) WELL TEG = Thermoelectric Generator + Well Head Waste Heat + Lead-Acid Battery; (9) GRID = Ocean Floor Electrical Grid + Lead-Acid Battery; and (10) DOC = Deep Ocean Current + Lead-Acid Battery.« less

New core-reflector boundary conditions for transient nodal reactor calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, E.K.; Kim, C.H.; Joo, H.K.

1995-09-01

New core-reflector boundary conditions designed for the exclusion of the reflector region in transient nodal reactor calculations are formulated. Spatially flat frequency approximations for the temporal neutron behavior and two types of transverse leakage approximations in the reflector region are introduced to solve the transverse-integrated time-dependent one-dimensional diffusion equation and then to obtain relationships between net current and flux at the core-reflector interfaces. To examine the effectiveness of new core-reflector boundary conditions in transient nodal reactor computations, nodal expansion method (NEM) computations with and without explicit representation of the reflector are performed for Laboratorium fuer Reaktorregelung und Anlagen (LRA) boilingmore » water reactor (BWR) and Nuclear Energy Agency Committee on Reactor Physics (NEACRP) pressurized water reactor (PWR) rod ejection kinetics benchmark problems. Good agreement between two NEM computations is demonstrated in all the important transient parameters of two benchmark problems. A significant amount of CPU time saving is also demonstrated with the boundary condition model with transverse leakage (BCMTL) approximations in the reflector region. In the three-dimensional LRA BWR, the BCMTL and the explicit reflector model computations differ by {approximately}4% in transient peak power density while the BCMTL results in >40% of CPU time saving by excluding both the axial and the radial reflector regions from explicit computational nodes. In the NEACRP PWR problem, which includes six different transient cases, the largest difference is 24.4% in the transient maximum power in the one-node-per-assembly B1 transient results. This difference in the transient maximum power of the B1 case is shown to reduce to 11.7% in the four-node-per-assembly computations. As for the computing time, BCMTL is shown to reduce the CPU time >20% in all six transient cases of the NEACRP PWR.« less

J-2X Turbopump Cavitation Diagnostics

NASA Technical Reports Server (NTRS)

Santi, I. Michael; Butas, John P.; Tyler, Thomas R., Jr.; Aguilar, Robert; Sowers, T. Shane

2010-01-01

The J-2X is the upper stage engine currently being designed by Pratt & Whitney Rocketdyne (PWR) for the Ares I Crew Launch Vehicle (CLV). Propellant supply requirements for the J-2X are defined by the Ares Upper Stage to J-2X Interface Control Document (ICD). Supply conditions outside ICD defined start or run boxes can induce turbopump cavitation leading to interruption of J-2X propellant flow during hot fire operation. In severe cases, cavitation can lead to uncontained engine failure with the potential to cause a vehicle catastrophic event. Turbopump and engine system performance models supported by system design information and test data are required to predict existence, severity, and consequences of a cavitation event. A cavitation model for each of the J-2X fuel and oxidizer turbopumps was developed using data from pump water flow test facilities at Pratt & Whitney Rocketdyne (PWR) and Marshall Space Flight Center (MSFC) together with data from Powerpack 1A testing at Stennis Space Center (SSC) and from heritage systems. These component models were implemented within the PWR J-2X Real Time Model (RTM) to provide a foundation for predicting system level effects following turbopump cavitation. The RTM serves as a general failure simulation platform supporting estimation of J-2X redline system effectiveness. A study to compare cavitation induced conditions with component level structural limit thresholds throughout the engine was performed using the RTM. Results provided insight into system level turbopump cavitation effects and redline system effectiveness in preventing structural limit violations. A need to better understand structural limits and redline system failure mitigation potential in the event of fuel side cavitation was indicated. This paper examines study results, efforts to mature J-2X turbopump cavitation models and structural limits, and issues with engine redline detection of cavitation and the use of vehicle-side abort triggers to augment the engine redline system.

Unique Spectroscopy and Imaging of Terrestrial Planets with JWST

NASA Astrophysics Data System (ADS)

Villanueva, Geronimo Luis; JWST Mars Team

2017-06-01

In this talk, I will present the main capabilities of the James Webb Space Telescope (JWST) for performing observations of terrestrial planets, using Mars as a test case. The distinctive vantage point of JWST at the Sun-Earth Lagrange point (L2) will allow sampling the full observable disk, permitting the study of short-term phenomena, diurnal processes (across the East-West axis) and latitudinal processes between the hemispheres (including seasonal effects) with excellent spatial resolutions (0.07 arcsec at 2 um). Spectroscopic observations will be achievable in the 0.7-5 um spectral region with NIRSpec at a maximum resolving power of 2700, and with 8000 in the 1-1.25 um range. Imaging will be attainable with NIRCam at 4.3 um and with two narrow filters near 2 um, while the nightside will be accessible with several filters in the 0.5 to 2 um. Such a powerful suite of instruments will be a major asset for the exploration and characterization of Mars, and terrestrial planets in general. Some science cases include the mapping of the water D/H ratio, investigations of the Martian mesosphere via the characterization of the non-LTE CO2 emission at 4.3 um, studies of chemical transport via observations of the O2 nightglow at 1.27 um, high cadence mapping of the variability dust and water ice clouds, and sensitive searches for trace species and hydrated features on the planetary surface.

Development and External Validation of a Prognostic Nomogram for Metastatic Uveal Melanoma

PubMed Central

Valpione, Sara; Moser, Justin C.; Parrozzani, Raffaele; Bazzi, Marco; Mansfield, Aaron S.; Mocellin, Simone; Pigozzo, Jacopo; Midena, Edoardo; Markovic, Svetomir N.; Aliberti, Camillo; Campana, Luca G.; Chiarion-Sileni, Vanna

2015-01-01

Background Approximately 50% of patients with uveal melanoma (UM) will develop metastatic disease, usually involving the liver. The outcome of metastatic UM (mUM) is generally poor and no standard therapy has been established. Additionally, clinicians lack a validated prognostic tool to evaluate these patients. The aim of this work was to develop a reliable prognostic nomogram for clinicians. Patients and Methods Two cohorts of mUM patients, from Veneto Oncology Institute (IOV) (N=152) and Mayo Clinic (MC) (N=102), were analyzed to develop and externally validate, a prognostic nomogram. Results The median survival of mUM was 17.2 months in the IOV cohort and 19.7 in the MC cohort. Percentage of liver involvement (HR 1.6), elevated levels of serum LDH (HR 1.6), and a WHO performance status=1 (HR 1.5) or 2–3 (HR 4.6) were associated with worse prognosis. Longer disease-free interval from diagnosis of UM to that of mUM conferred a survival advantage (HR 0.9). The nomogram had a concordance probability of 0.75 (SE .006) in the development dataset (IOV), and 0.80 (SE .009) in the external validation (MC). Nomogram predictions were well calibrated. Conclusions The nomogram, which includes percentage of liver involvement, LDH levels, WHO performance status and disease free-interval accurately predicts the prognosis of mUM and could be useful for decision-making and risk stratification for clinical trials. PMID:25780931

VizieR Online Data Catalog: A dust model for bet Pic from 0.58 to 870um (Ballering+, 2016)

NASA Astrophysics Data System (ADS)

Ballering, N. P.; Su, K. Y. L.; Rieke, G. H.; Gaspar, A.

2016-08-01

β Pic was imaged with the HST/STIS CCD in coronagraphic (50CORON) mode under program GO-12551 (PI: Apai), and the results of these observations were published in Apai et al. (2015ApJ...800..136A). The instrument bandpass is set by the response of the CCD and centered at 0.58um. We searched the HST archive and found previously unpublished observations of β Pic with the WFC3 instrument in the IR channel (filter F110W at ~1.16um) from program GO-11150 (PI: Graham). The Spitzer/MIPS observations of β Pic were taken under the Spitzer Guaranteed Time Observing Program 90 (PI: M. Werner). The data at all three bands (24, 70, and 160um) are published here for the first time. Two sets of 24um observations were obtained. The first set was obtained on 2004 March 20, the second set of data was obtained on 2004 April 11. Two sets of 70um observations were obtained. The first set was obtained on 2004 April 12. The second set was obtained on 2005 April 4. Herschel/PACS 70um scan map observations of β Pic (PI G. Olofsson, observation IDs 1342186612 and 1342186613) were published by Vandenbussche et al. (2010A&A...518L.133V). We used the ALMA 870um continuum image previously published by Dent et al. (2014Sci...343.1490D). (1 data file).

The gut microbiota metabolism of pomegranate or walnut ellagitannins yields two urolithin-metabotypes that correlate with cardiometabolic risk biomarkers: Comparison between normoweight, overweight-obesity and metabolic syndrome.

PubMed

Selma, María V; González-Sarrías, Antonio; Salas-Salvadó, Jordi; Andrés-Lacueva, Cristina; Alasalvar, Cesarettin; Örem, Asım; Tomás-Barberán, Francisco A; Espín, Juan C

2018-06-01

Urolithins are microbial metabolites produced after consumption of ellagitannin-containing foods such as pomegranates and walnuts. Parallel to isoflavone-metabolizing phenotypes, ellagitannin-metabolizing phenotypes (urolithin metabotypes A, B and 0; UM-A, UM-B and UM-0, respectively) can vary among individuals depending on their body mass index (BMI), but correlations between urolithin metabotypes (UMs) and cardiometabolic risk (CMR) factors are unexplored. We investigated the association between UMs and CMR factors in individuals with different BMI and health status. UM was identified using UPLC-ESI-qToF-MS in individuals consuming pomegranate or nuts. The associations between basal CMR factors and the urine urolithin metabolomic signature were explored in 20 healthy normoweight individuals consuming walnuts (30 g/d), 49 healthy overweight-obese individuals ingesting pomegranate extract (450 mg/d) and 25 metabolic syndrome (MetS) patients consuming nuts (15 g-walnuts, 7.5 g-hazelnuts and 7.5 g-almonds/d). Correlations between CMR factors and urolithins were found in overweight-obese individuals. Urolithin-A (mostly present in UM-A) was positively correlated with apolipoprotein A-I (P ≤ 0.05) and intermediate-HDL-cholesterol (P ≤ 0.05) while urolithin-B and isourolithin-A (characteristic from UM-B) were positively correlated with total-cholesterol, LDL-cholesterol (P ≤ 0.001), apolipoprotein B (P ≤ 0.01), VLDL-cholesterol, IDL-cholesterol, oxidized-LDL and apolipoprotein B:apolipoprotein A-I ratio (P ≤ 0.05). In MetS patients, urolithin-A only correlated inversely with glucose (P ≤ 0.05). Statin-treated MetS patients with UM-A showed a lipid profile similar to that of healthy normoweight individuals while a poor response to lipid-lowering therapy was observed in MB patients. UMs are potential CMR biomarkers. Overweight-obese individuals with UM-B are at increased risk of cardiometabolic disease, whereas urolithin-A production could protect against CMR factors. Further research is warranted to explore these associations in larger cohorts and whether the effect of lipid-lowering drugs or ellagitannin-consumption on CMR biomarkers depends on individuals' UM. NCT01916239 (https://clinicaltrials.gov/ct2/show/NCT01916239) and ISRCTN36468613 (http://www.isrctn.com/ISRCTN36468613). Copyright © 2017 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Downar, Thomas

This report summarizes the current status of VERA-CS Verification and Validation for PWR Core Follow operation and proposes a multi-phase plan for continuing VERA-CS V&V in FY17 and FY18. The proposed plan recognizes the hierarchical nature of a multi-physics code system such as VERA-CS and the importance of first achieving an acceptable level of V&V on each of the single physics codes before focusing on the V&V of the coupled physics solution. The report summarizes the V&V of each of the single physics codes systems currently used for core follow analysis (ie MPACT, CTF, Multigroup Cross Section Generation, and BISONmore » / Fuel Temperature Tables) and proposes specific actions to achieve a uniformly acceptable level of V&V in FY17. The report also recognizes the ongoing development of other codes important for PWR Core Follow (e.g. TIAMAT, MAMBA3D) and proposes Phase II (FY18) VERA-CS V&V activities in which those codes will also reach an acceptable level of V&V. The report then summarizes the current status of VERA-CS multi-physics V&V for PWR Core Follow and the ongoing PWR Core Follow V&V activities for FY17. An automated procedure and output data format is proposed for standardizing the output for core follow calculations and automatically generating tables and figures for the VERA-CS Latex file. A set of acceptance metrics is also proposed for the evaluation and assessment of core follow results that would be used within the script to automatically flag any results which require further analysis or more detailed explanation prior to being added to the VERA-CS validation base. After the Automation Scripts have been completed and tested using BEAVRS, the VERA-CS plan proposes the Watts Bar cycle depletion cases should be performed with the new cross section library and be included in the first draft of the new VERA-CS manual for release at the end of PoR15. Also, within the constraints imposed by the proprietary nature of plant data, as many as possible of the FY17 AMA Plant Core Follow cases should also be included in the VERA-CS manual at the end of PoR15. After completion of the ongoing development of TIAMAT for fully coupled, full core calculations with VERA-CS / BISON 1.5D, and after the completion of the refactoring of MAMBA3D for CIPS analysis in FY17, selected cases from the VERA-CS validation based should be performed, beginning with the legacy cases of Watts Bar and BEAVRS in PoR16. Finally, as potential Phase III future work some additional considerations are identified for extending the VERA-CS V&V to other reactor types such as the BWR.« less

Unit 5, STA. 50+00+RB, Orner Building, First U.M. Church Rectory, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Unit 5, STA. 50+00+RB, Orner Building, First U.M. Church Rectory, & First U.M. Church-context - Johnstown Local Flood Protection Project, Beginning on Conemaugh River approx 3.8 miles downstream from confluence of Little Conemaugh & Stony Creek Rivers at Johnstown, Johnstown, Cambria County, PA

VizieR Online Data Catalog: 24um excesses in clusters & membership of NGC2244 (Meng+, 2017)

NASA Astrophysics Data System (ADS)

Meng, H. Y. A.; Rieke, G. H.; Su, K. Y. L.; Gaspar, A.

2017-09-01

We re-measured the Spitzer/MIPS 24um photometry for all the clusters except for a few noted in Appendix A. We obtained the 24um data from the Spitzer Heritage Archive between 2004 Jan 28 and 2008 Oct 23. (3 data files).

VizieR Online Data Catalog: X-ray AGNs with Subaru/FMOS NIR observations (Suh+, 2015)

NASA Astrophysics Data System (ADS)

Suh, H.; Hasinger, G.; Steinhardt, C.; Silverman, J. D.; Schramm, M.

2016-03-01

We performed NIR spectroscopic observations for the AGN sources with the FMOS high-resolution spectrographs on the Subaru telescope; in J-short (0.92-1.12um), J-long (1.11-1.35um), H-short (1.40-1.60um), and H-long (1.60-1.80um) coverage with a spectral resolution of R~2200. The data span the 2012 Mar 25-2013 Oct 24 period. In addition to NIR spectra, we use existing optical spectroscopy (see section 3.2). (2 data files).

VizieR Online Data Catalog: MILO. I. HD 7449 radial velocities (Rodigas+, 2016)

NASA Astrophysics Data System (ADS)

Rodigas, T. J.; Arriagada, P.; Faherty, J.; Anglada-Escude, G.; Kaib, N.; Butler, R. P.; Shectman, S.; Weinberger, A.; Males, J. R.; Morzinski, K. M.; Close, L. M.; Hinz, P. M.; Crane, J. D.; Thompson, I.; Teske, J.; Diaz, M.; Minniti, D.; Lopez-Morales, M.; Adams, F. C.; Boss, A. P.

2016-04-01

We observed HD 7449 using the Magellan Clay Telescope at the Las Campanas Observatory in Chile on the nights of UT 2014 November 5 and 22. We observed the star with VisAO at Ys (0.99um) and with Clio-2 at H (1.65um) and Ks (2.15um) on the first night and with VisAO at r' (0.63um), i' (0.77um), z' (0.91um), and with Clio-2 at J (1.1um) on the second night. RV data on HD 7449 were first acquired as part of the Magellan Planet Search Program, which originally made use of the MIKE echelle spectrometer (R~70000 in the blue and ~50000 in the red; wavelength coverage ranges from 3900 to 6200Å) on the Magellan Clay telescope until 2009 September. HD 7449 was subsequently observed using the Carnegie Magellan/PFS (3880-6680Å with R~80000 in the iodine region). We also included in our analysis RVs measured with HARPS and CORALIE. These RVs were originally reported in Dumusque et al. (2011, J/A+A/535/A55). HARPS data on HD 7449 has been supplemented by the ESO archive. See section 2.2 for further explanations. (1 data file).

User Data Package - Energy-Efficient Windows and Window Coverings for Naval Housing

DTIC Science & Technology

1990-07-01

1765 33 Savannah 1819 32 Tucson 1800 32 Winslow 4782 35 Idaho Yuma 974 33 Boise 5809 44 Lewiston 5542 46 Arkansas Pocatello 7033 43 Fort Smith 3292 35...Alexandria, VA DODDS Pac, FAC, Okinawa, Japan DOE Fed Energy Mgt Program, Wash, DC: INEL Tech Lib Reports Sta. Idaho Falls. ID; Knolls Atomic Pwr Lab

77 FR 9960 - Final Environmental Impact Statement for Extension of F-Line Streetcar Service to Fort Mason...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-21

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-PWRO-1103-8840; 2051-P580-579] Final... AGENCY: National Park Service, Department of the Interior. ACTION: Notice of Availability of the Final... resources. Many also suggested various design ideas and other measures to help reduce these impacts. In...

78 FR 38359 - Approval of Record of Decision for Relocation of Cattle Point Road, San Juan Island National...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-26

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-PWR-PWRO-12863; PPPWSAJHA0 PPMPSAS1Z.Y00000... Park, San Juan County, Washington AGENCY: National Park Service, Interior. ACTION: Notice of Record of....2), the Department of the Interior, National Park Service has prepared and approved a Record of...

77 FR 31655 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses and Combined Licenses...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-29

... controverted. In addition, the requestor/petitioner shall provide a brief explanation of the bases for the... against burst, as discussed in Regulatory Guide (RG) 1.121, ``Bases for Plugging Degraded PWR [Pressurized... Institute] 97-06, Revision 3, ``Steam Generator Program Guidelines'' (Reference 1) and RG 1.121, ``Bases for...

Manufacturing Methods and Technology Measure for Fabrication of Silicon Transcalent Rectifier.

DTIC Science & Technology

1980-09-01

Prod Test/Eval’, z HA Kotler a Patent- Power & E 1 RM Roderick Env. Eng. & Test 1 JB Grosh Iron Mouptain - .l TUBE PARTS MFG. 5 RL SPALDING...AFAL/PODI ATTN: Working Group on Pwr. Devices (Mr. Philip Herron) 201 Varick Street Wright Patterson AFB, OH 45433 New York, NY 10014 Commander Mr

Utility of Serum Creatinine, Creatine Kinase and Urinary Myoglobin in Detecting Acute Renal Failure due to Rhabdomyolysis in Trauma and Electrical Burns Patients.

PubMed

Bhavsar, Preetish; Rathod, Kirtikumar Jagdish; Rathod, Darshana; Chamania, C S

2013-02-01

Rhabdomyolysis due to trauma and burns is an important cause of acute renal failure (ARF) secondary to myoglobinuria. To prevent morbidity and mortality from ARF due to rhabdomyolysis, early detection of ARF by monitoring the biochemical parameters such as serum creatinine, serum creatine kinase (CK), and urinary myoglobin (UM) can be helpful. The aims of the study were (1) to detect ARF due to rhabdomyolysis using serum creatinine, serum CK, and UM in trauma and electrical burn patients (2) to compare utility of these parameters in early prediction of ARF in patients of rhabdomyolysis. A total of 50 patients with trauma and electrical burns were included in the study. Serum creatinine, serum CK, and UM measurements were done at the time of admission and after 48 h. Diagnosis of ARF was made in the patients by Rifle's criteria. The presence of significant elevation of creatinine, serum CK, and UM at the time of admission and after 48 h was compared in patients developing ARF by Fisher's exact test. Fifteen of the 50 patients developed ARF as per the defined criteria. Of these, 9 patients (60 %) had raised level of serum creatinine above 1.4 mg% at admission and 14 patients (93.33 %) had CK level >1250 U/L at admission, whereas UM was positive in 6 (40 %) patients. Serum creatinine was significantly raised in all of the 15 ARF patients (100 %) after 48 h of admission and serum CK was raised in 14 of the 15 ARF patients (93.33 %). UM was negative in all the patients after 48 h of admission. Statistical analysis showed that rise in serum CK on admission was significantly increased in patients developing ARF as compared with serum creatinine and UM (P < 0.0001). On admission, CK is a better predictor of ARF due to rhabdomyolysis than creatinine and UM. Initial creatinine is a better predictor of ARF due to rhabdomyolysis than UM. UM assay is not a good investigation for early prediction of ARF in rhabdomyolysis.

Ga Lithography in Sputtered Niobium for Superconductive Micro and Nanowires.

DOE PAGES

Henry, Michael David; Lewis, Rupert M.; Wolfley, Steven L.; ...

2014-08-18

This work demonstrates the use of FIB implanted Ga as a lithographic mask for plasma etching of Nb films. Using a highly collimated Ga beam of a FIB, Nb is implanted 12 nm deep with a 14 nm thick Ga layer providing etch selectivity better than 15:1 with fluorine based etch chemistry. Implanted square test patterns, both 10 um by and 10 um and 100 um by 100 um, demonstrate that doses above than 7.5 x 1015 cm-2 at 30 kV provide adequate mask protection for a 205 nm thick, sputtered Nb film. The resolution of this dry lithographic techniquemore » is demonstrated by fabrication of nanowires 75 nm wide by 10 um long connected to 50 um wide contact pads. The residual resistance ratio of patterned Nb films was 3. The superconducting transition temperature, Tc =7.7 K, was measured using MPMS. This nanoscale, dry lithographic technique was extended to sputtered TiN and Ta here and could be used on other fluorine etched superconductors such as NbN, NbSi, and NbTi.« less

VizieR Online Data Catalog: Reflectance spectra of 12 Trojans and Hildas (Marsset+, 2014)

NASA Astrophysics Data System (ADS)

Marsset, M.; Vernazza, P.; Gourgeot, F.; Dumas, C.; Birlan, M.; Lamy, P.; Binzel, R. P.

2014-07-01

We present 17 reflectance spectra of 12 high albedo (pv>0.14) Trojans (8 objects) and Hildas (4 objects) obtained with the ESO/VLT Echelle spectrograph X-SHOOTER in the 0.3-2.2um spectral range (14 spectra) and with the NASA/IRTF spectrograph SpeX in the 0.8-2.5um spectral range (3 spectra). X-SHOOTER spectra were normalized to unity at 0.55um and SpeX spectra were normalized to unity at 2.2um . The spectra presented in this work were collected between April and December 2013. (18 data files).

BCR ligation induced by IgM stimulation results in gene expression and functional changes only in IgV H unmutated chronic lymphocytic leukemia (CLL) cells.

PubMed

Guarini, Anna; Chiaretti, Sabina; Tavolaro, Simona; Maggio, Roberta; Peragine, Nadia; Citarella, Franca; Ricciardi, Maria Rosaria; Santangelo, Simona; Marinelli, Marilisa; De Propris, Maria Stefania; Messina, Monica; Mauro, Francesca Romana; Del Giudice, Ilaria; Foà, Robert

2008-08-01

Chronic lymphocytic leukemia (CLL) patients exhibit a variable clinical course. To investigate the association between clinicobiologic features and responsiveness of CLL cells to anti-IgM stimulation, we evaluated gene expression changes and modifications in cell-cycle distribution, proliferation, and apoptosis of IgV(H) mutated (M) and unmutated (UM) samples upon BCR cross-linking. Unsupervised analysis highlighted a different response profile to BCR stimulation between UM and M samples. Supervised analysis identified several genes modulated exclusively in the UM cases upon BCR cross-linking. Functional gene groups, including signal transduction, transcription, cell-cycle regulation, and cytoskeleton organization, were up-regulated upon stimulation in UM cases. Cell-cycle and proliferation analyses confirmed that IgM cross-linking induced a significant progression into the G(1) phase and a moderate increase of proliferative activity exclusively in UM patients. Moreover, we observed only a small reduction in the percentage of subG(0/1) cells, without changes in apoptosis, in UM cases; contrariwise, a significant increase of apoptotic levels was observed in stimulated cells from M cases. These results document that a differential genotypic and functional response to BCR ligation between IgV(H) M and UM cases is operational in CLL, indicating that response to antigenic stimulation plays a pivotal role in disease progression.

"Uh" and "Um" Revisited: Are They Interjections for Signaling Delay?

ERIC Educational Resources Information Center

O'Connell, Daniel C.; Kowal, Sabine

2005-01-01

Clark and Fox Tree (2002) have presented empirical evidence, based primarily on the London-Lund corpus (LL; Svartvik & Quirk, 1980), that the fillers "uh" and "um" are conventional English words that signal a speaker's intention to initiate a minor and a major delay, respectively. We present here empirical analyses of "uh" and "um" and of silent…

The attitudes, role & knowledge of mental health nurses towards euthanasia because of unbearable mental suffering in Belgium: a pilot study.

PubMed

Demedts, Dennis; Roelands, Marc; Libbrecht, Julien; Bilsen, Johan

2018-05-26

Euthanasia because of unbearable mental suffering (UMS euthanasia) has been legal in Belgium since 2002, under certain circumstances that govern careful practice. Despite the legal framework, there are specific difficulties and concerns regarding UMS euthanasia. Mental health nurses are often involved in the process, but little is known about their attitudes towards UMS euthanasia, their role and their knowledge. To determine the attitudes, role and knowledge of mental health nurses regarding UMS euthanasia. A cross-sectional survey was performed at a convenience sample of four psychiatric hospitals in Belgium (n=133) as a pilot study. Self-administered questionnaires were provided to mental health nurses. Half the nurses in our sample had been involved at least once in the process of UMS euthanasia. A large majority of mental health nurses were supportive of UMS euthanasia. Nurses show differences in attitudes related to the different psychiatric pathologies of the patients, and in whether or not minors are involved. In some cases, they believed that the mental suffering of psychiatric patients can be unbearable and irreversible and that psychiatric patients can be competent to voluntarily request UMS euthanasia. Nurses stated that they have an important role in the UMS euthanasia process, but also demanded more knowledge and clear guidelines to implement the procedure. Nurses have a key role regarding UMS euthanasia but face several challenges: the recent process, resistance to a multidisciplinary approach by psychiatrists and an unclear role defined by the legal framework. Nurses do not appear to have a common voice on the topic and the development of clear guidelines appears to be essential. Social recovery can offer a way out of an UMS euthanasia request, but it will not always offer a solution. Sufficient attention must be paid to how mental health nurses can be involved in the process of UMS euthanasia at various levels: bedside practice, healthcare management, education and policy. A form of systematic cooperation between nurses, physicians and patients can contribute to the utmost careful decision-making process needed in these cases. There is a need for proper training in: knowledge of psychiatric pathologies and remaining treatment options; communication skills; the legal framework and all its difficulties; transdisciplinary and multicultural approaches; ethical reflection and how nurses handle their own emotions. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

The short form of the recombinant CAL-A-type lipase UM03410 from the smut fungus Ustilago maydis exhibits an inherent trans-fatty acid selectivity.

PubMed

Brundiek, Henrike; Saß, Stefan; Evitt, Andrew; Kourist, Robert; Bornscheuer, Uwe T

2012-04-01

The Ustilago maydis lipase UM03410 belongs to the mostly unexplored Candida antarctica lipase (CAL-A) subfamily. The two lipases with [corrected] the highest identity are a lipase from Sporisorium reilianum and the prototypic CAL-A. In contrast to the other CAL-A-type lipases, this hypothetical U. maydis lipase is annotated to possess a prolonged N-terminus of unknown function. Here, we show for the first time the recombinant expression of two versions of lipase UM03410: the full-length form (lipUMf) and an Nterminally truncated form (lipUMs). For comparison to the prototype, the expression of recombinant CAL-A in E. coli was investigated. Although both forms of lipase UM03410 could be expressed functionally in E. coli, the N-terminally truncated form (lipUMs) demonstrated significantly higher activities towards p-nitrophenyl esters. The functional expression of the N-terminally truncated lipase was further optimized by the appropriate choice of the E. coli strain, lowering the cultivation temperature to 20 °C and enrichment of the cultivation medium with glucose. Primary characteristics of the recombinant lipase are its pH optimum in the range of 6.5-7.0 and its temperature optimum at 55 °C. As is typical for lipases, lipUM03410 shows preference for long chain fatty acid esters with myristic acid ester (C14:0 ester) being the most preferred one.More importantly, lipUMs exhibits an inherent preference for C18:1Δ9 trans and C18:1Δ11 trans-fatty acid esters similar to CAL-A. Therefore, the short form of this U. maydis lipase is the only other currently known lipase with a distinct trans-fatty acid selectivity.

Uh and um revisited: are they interjections for signaling delay?

PubMed

O'Connell, Daniel C; Kowal, Sabine

2005-11-01

Clark and Fox Tree (2002) have presented empirical evidence, based primarily on the London-Lund corpus (LL; Svartvik & Quirk, 1980), that the fillers uh and um are conventional English words that signal a speaker's intention to initiate a minor and a major delay, respectively. We present here empirical analyses of uh and um and of silent pauses (delays) immediately following them in six media interviews of Hillary Clinton. Our evidence indicates that uh and um cannot serve as signals of upcoming delay, let alone signal it differentially: In most cases, both uh and um were not followed by a silent pause, that is, there was no delay at all; the silent pauses that did occur after um were too short to be counted as major delays; finally, the distributions of durations of silent pauses after uh and um were almost entirely overlapping and could therefore not have served as reliable predictors for a listener. The discrepancies between Clark and Fox Tree's findings and ours are largely a consequence of the fact that their LL analyses reflect the perceptions of professional coders, whereas our data were analyzed by means of acoustic measurements with the PRAAT software (www.praat.org). A comparison of our findings with those of O'Connell, Kowal, and Ageneau (2005) did not corroborate the hypothesis of Clark and Fox Tree that uh and um are interjections: Fillers occurred typically in initial, interjections in medial positions; fillers did not constitute an integral turn by themselves, whereas interjections did; fillers never initiated cited speech, whereas interjections did; and fillers did not signal emotion, whereas interjections did. Clark and Fox Tree's analyses were embedded within a theory of ideal delivery that we find inappropriate for the explication of these phenomena.

Clustering according to urolithin metabotype explains the interindividual variability in the improvement of cardiovascular risk biomarkers in overweight-obese individuals consuming pomegranate: A randomized clinical trial.

PubMed

González-Sarrías, Antonio; García-Villalba, Rocío; Romo-Vaquero, María; Alasalvar, Cesarettin; Örem, Asim; Zafrilla, Pilar; Tomás-Barberán, Francisco A; Selma, María V; Espín, Juan Carlos

2017-05-01

The pomegranate lipid-lowering properties remain controversial, probably due to the interindividual variability in polyphenol (ellagitannins) metabolism. We aimed at investigating whether the microbially derived ellagitannin-metabolizing phenotypes, i.e. urolithin metabotypes A, (UM-A), B (UM-B), and 0 (UM-0), influence the effects of pomegranate extract (PE) consumption on 18 cardiovascular risk biomarkers in healthy overweight-obese individuals. A double-blind, crossover, dose-response, randomized, placebo-controlled trial was conducted. The study (POMEcardio) consisted of two test phases (dose-1 and dose-2, lasting 3 weeks each) and a 3-week washout period between each phase. Forty-nine participants (BMI > 27 kg/m 2 ) daily consumed one (dose-1, 160 mg phenolics/day) or four (dose-2, 640 mg phenolics/day) PE or placebo capsules. Notably, UM-B individuals showed the highest baseline cardiovascular risk. After dose-2, total cholesterol (-15.5 ± 3.7%), LDL-cholesterol (-14.9 ± 2.1%), small LDL-cholesterol (-47 ± 7%), non-HDL-cholesterol (-11.3 ± 2.5%), apolipoprotein-B (-12 ± 2.2%), and oxidized LDL-cholesterol -24 ± 2.5%) dose dependently decreased (P < 0.05) but only in UM-B subjects. These effects were partially correlated with urolithin production and the increase in Gordonibacter levels. Three (50%) nonproducers (UM-0) became producers following PE consumption. UM clustering suggests a personalized effect of ellagitannin-containing foods and could explain the controversial pomegranate benefits. Research on the specific role of urolithins and the microbiota associated with each UM is warranted. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Medical condition and care of undocumented migrants in ambulatory clinics in Tel Aviv, Israel: assessing unmet needs.

PubMed

Mor, Zohar; Raveh, Yuval; Lurie, Ido; Leventhal, Alex; Gamzu, Roni; Davidovitch, Nadav; Benari, Orel; Grotto, Itamar

2017-07-14

Approximately 150,000 undocumented migrants (UM) who are medically uninsured reside in Israel, including ~50,000 originating from the horn of Africa (MHA). Free medical-care is provided by two walk-in clinics in Tel-Aviv. This study aims to compare the medical complaints of UM from different origins, define their community health needs and assess gaps between medical needs and available services. This cross-sectional study included a random sample of 610 UM aged 18-64 years, who were treated in these community clinics between 2008 and 2011. The study compared UM who had complex medical conditions which necessitated referral to more equipped medical settings with UM having mild/simple medical conditions, who were treated at the clinics. MHA were younger, unemployed and more commonly males compared with UM originating from other countries. MHA also had longer referral-delays and visited the clinics less frequently. UM with complex medical conditions were more commonly females, had chronic diseases and demonstrated longer referral-delays than those who had mild/simple medical conditions. The latter more commonly presented with complained of respiratory, muscular and skeletal discomfort. In multivariate analysis, the variables which predicted complex medical conditions included female gender, chronic illnes and self-referral to the clinics. The ambulatory clinics were capable of responding to mild/simple medical conditions. Yet, the health needs of women and migrants suffering from complex medical conditions and chronic diseases necessitated referrals to secondary/tertiary medical settings, while jeopardizing the continuity of care. The health gaps can be addressed by a more holistic social approach, which includes integration of UM in universal health insurance.

High-speed, large-area, p-i-n InGaAs photodiode linear array at 2-micron wavelength

NASA Astrophysics Data System (ADS)

Joshi, Abhay; Datta, Shubhashish

2012-06-01

We present 16-element and 32-element lattice-mismatched InGaAs photodiode arrays having a cut-off wavelength of ~2.2 um. Each 100 um × 200 um large pixel of the 32-element array has a capacitance of 2.5 pF at 5 V reverse bias, thereby allowing a RC-limited bandwidth of ~1.3 GHz. At room temperature, each pixel demonstrates a dark current of 25 uA at 5 V reverse bias. Corresponding results for the 16-element array having 200 um × 200 um pixels are also reported. Cooling the photodiode array to 150K is expected to reduce its dark current to < 50 nA per pixel at 5 V reverse bias. Additionally, measurement results of 2-micron single photodiodes having 16 GHz bandwidth and corresponding PIN-TIA photoreceiver having 6 GHz bandwidth are also reported.

Development of a non-contextual model for determining the autonomy level of intelligent unmanned systems

NASA Astrophysics Data System (ADS)

Durst, Phillip J.; Gray, Wendell; Trentini, Michael

2013-05-01

A simple, quantitative measure for encapsulating the autonomous capabilities of unmanned systems (UMS) has yet to be established. Current models for measuring a UMS's autonomy level require extensive, operational level testing, and provide a means for assessing the autonomy level for a specific mission/task and operational environment. A more elegant technique for quantifying autonomy using component level testing of the robot platform alone, outside of mission and environment contexts, is desirable. Using a high level framework for UMS architectures, such a model for determining a level of autonomy has been developed. The model uses a combination of developmental and component level testing for each aspect of the UMS architecture to define a non-contextual autonomous potential (NCAP). The NCAP provides an autonomy level, ranging from fully non- autonomous to fully autonomous, in the form of a single numeric parameter describing the UMS's performance capabilities when operating at that level of autonomy.

76 FR 23577 - Combined Notice of Filings #1

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-27

... Interconnection, L.L.C. submits tariff filing per 35.13(a)(2)(iii: Queue No. W3-124--Original Service Agreement No... Transmission Agreement with Auburndale Pwr Partners to be effective 5/1/2011. Filed Date: 04/21/2011. Accession... tariff filing per 35.13(a)(1): 04--21--11 Paris Rate Schedule 407 Settlement to be effective 3/31/2011...

Steam generators regulatory practices and issues in Spain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendoza, C.; Castelao, C.; Ruiz-Colino, J.

1997-02-01

This paper presents the actual status of Spanish Steam Generator tubes, actions developed by PWR plant owners and submitted to CSN, and regulatory activities related to tube degradation mechanisms analysis; NDT tube inspection techniques; tube, tubesheet and TSPs integrity studies; tube plugging/repair criteria; preventive and corrective measures including whole SGs replacement; tube leak measurement methods and other operational aspects.

Nuclear Engineering Computer Modules, Thermal-Hydraulics, TH-1: Pressurized Water Reactors.

ERIC Educational Resources Information Center

Reihman, Thomas C.

This learning module is concerned with the temperature field, the heat transfer rates, and the coolant pressure drop in typical pressurized water reactor (PWR) fuel assemblies. As in all of the modules of this series, emphasis is placed on developing the theory and demonstrating its use with a simplified model. The heart of the module is the PWR…

Organometallics in High Energy Chemistry.

DTIC Science & Technology

1983-10-31

Luines Physeical ftaenc Chemistry DepatneWu. SJI International. Menlo PWr *. CaiOwrnia M10 Rceived Nouvber 8. 1IM The otslytic formation of6nw carbon...support the idea that the metalloazocyclopropane intermediate is the reactive intermediate that leads to transalkylation. A discussion of the...exceptionally good correlation between the catalytic reactivity patterns of palladium black in its reactions with tertiary amines and those of homogeneous

Feasibility of recycling thorium in a fusion-fission hybrid/PWR symbiotic system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Josephs, J.M.

1980-12-31

A study was made of the economic impact of high levels of radioactivity in the thorium fuel cycle. The sources of this radioactivity and means of calculating the radioactive levels at various stages in the fuel cycle are discussed and estimates of expected levels are given. The feasibility of various methods of recycling thorium is discussed. These methods include direct recycle, recycle after storage for 14 years to allow radioactivity to decrease, shortening irradiation times to limit radioactivity build up, and the use of the window in time immediately after reprocessing where radioactivity levels are diminished. An economic comparison ismore » made for the first two methods together with the throwaway option where thorium is not recycled using a mass energy flow model developed for a CTHR (Commercial Tokamak Hybrid Reactor), a fusion fission hybrid reactor which serves as fuel producer for several PWR reactors. The storage option is found to be most favorable; however, even this option represents a significant economic impact due to radioactivity of 0.074 mills/kW-h which amounts to $4 x 10/sup 9/ over a 30 year period assuming a 200 gigawatt supply of electrical power.« less

Effect of surface state on the oxidation behavior of welded 308L in simulated nominal primary water of PWR

NASA Astrophysics Data System (ADS)

Ming, Hongliang; Zhang, Zhiming; Wang, Jiazhen; Zhu, Ruolin; Ding, Jie; Wang, Jianqiu; Han, En-Hou; Ke, Wei

2015-05-01

The oxidation behavior of 308L weld metal (WM) with different surface state in the simulated nominal primary water of pressurized water reactor (PWR) was studied by scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) analyzer and X-ray photoelectron spectroscopy (XPS). After 480 h immersion, a duplex oxide film composed of a Fe-rich outer layer (Fe3O4, Fe2O3 and a small amount of NiFe2O4, Ni(OH)2, Cr(OH)3 and (Ni, Fe)Cr2O4) and a Cr-rich inner layer (FeCr2O4 and NiCr2O4) can be formed on the 308L WM samples with different surface state. The surface state has no influence on the phase composition of the oxide films but obviously affects the thickness of the oxide films and the morphology of the oxides (number & size). With increasing the density of dislocations and subgrain boundaries in the cold-worked superficial layer, the thickness of the oxide film, the number and size of the oxides decrease.

Fundamental metallurgical aspects of axial splitting in zircaloy cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, H. M.

Fundamental metallurgical aspects of axial splitting in irradiated Zircaloy cladding have been investigated by microstructural characterization and analytical modeling, with emphasis on application of the results to understand high-burnup fuel failure under RIA situations. Optical microscopy, SEM, and TEM were conducted on BWR and PWR fuel cladding tubes that were irradiated to fluence levels of 3.3 x 10{sup 21} n cm{sup {minus}2} to 5.9 x 10{sup 21} n cm{sup {minus}2} (E > 1 MeV) and tested in hot cell at 292--325 C in Ar. The morphology, distribution, and habit planes of macroscopic and microscopic hydrides in as-irradiated and posttest claddingmore » were determined by stereo-TEM. The type and magnitude of the residual stress produced in association with oxide-layer growth and dense hydride precipitation, and several synergistic factors that strongly influence axial-splitting behavior were analyzed. The results of the microstructural characterization and stress analyses were then correlated with axial-splitting behavior of high-burnup PWR cladding reported for simulated-RIA conditions. The effects of key test procedures and their implications for the interpretation of RIA test results are discussed.« less

CHF considerations for highly moderated 100% MOX fuels PWRs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saphier, D.; Raymond, P.

1995-09-01

A feasibility study on using 100% MOX fuel in a PWR with increased moderating ratio, RMA, was initiated. In the proposed design all the parameters were chosen identical to the French 1450MW PWR, except the fuel pin diameter which was reduced to achieve higher moderating ratios, V{sub M}/V{sub F}, where V{sub M} and V{sub F} are the moderator and fuel volume respectively. Moderating ratios from 2 to 4 were considered. In the present study the thermal-hydraulic feasibility of using fuel assemblies with smaller diameter fuel pins was investigated. The major design constrain in this study was the critical heat fluxmore » (CHF). In order to maintain the fuel pin integrity under nominal operating and transient conditions, the minimum DNBR, (Departure from Nucleate Boiling Ratio given by CHF/q{close_quotes}{sub local}, where q{close_quotes}{sub local} is the local heat flux), has to be above a given value. The limitations of the existing CHF correlations for the present study are outlined. Two designs based on the conventional 17x17 fuel assembly and on the advanced 19x19 assembly meeting the MDNBR criteria and satisfying the control margin requirements, are proposed.« less

Development of new UV-I. I. Cerenkov Viewing Device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuribara, Masayuki; Nemoto, Koshichi

1994-02-01

The Cerenkov glow images from boiling-water reactors (BWR) and pressurized-water reactors (PWR) irradiated fuel assemblies are generally used for inspections. However, sometimes it is difficult or impossible to identify the image by the conventional Cerenkov Viewing Device (CVD), because of the long cooling time and/or low burnup. Now a new UV-I.I. (Ultra-Violet light Image Intensifier) CVD has been developed, which can detect the very weak Cerenkov glow from spent fuel assemblies. As this new device uses the newly developed proximity focused type UV-I.I., Cerenkov photons are used efficiently, producing better quality Cerenkov glow images. Moreover, since the image is convertedmore » to a video signal, it is easy to improve the signal to noise ratio (S/N) by an image processor. The new CVD was tested at BWR and PWR power plants in Japan, with fuel burnups ranging from 6,200--33,000 MWD/MTU (megawatt days per metric ton of uranium) and cooling times ranging from 370 to 6,200 d. The tests showed that the new CVD is superior to the conventional STA/CRIEPI CVD, and could detect very feeble Cerenkov glow images using an image processor.« less

Crack opening area estimates in pressurized through-wall cracked elbows under bending

DOE Office of Scientific and Technical Information (OSTI.GOV)

Franco, C.; Gilles, P.; Pignol, M.

1997-04-01

One of the most important aspects in the leak-before-break approach is the estimation of the crack opening area corresponding to potential through-wall cracks at critical locations during plant operation. In order to provide a reasonable lower bound to the leak area under such loading conditions, numerous experimental and numerical programs have been developed in USA, U.K. and FRG and widely discussed in literature. This paper aims to extend these investigations on a class of pipe elbows characteristic of PWR main coolant piping. The paper is divided in three main parts. First, a new simplified estimation scheme for leakage area ismore » described, based on the reference stress method. This approach mainly developed in U.K. and more recently in France provides a convenient way to account for the non-linear behavior of the material. Second, the method is carried out for circumferential through-wall cracks located in PWR elbows subjected to internal pressure. Finite element crack area results are presented and comparisons are made with our predictions. Finally, in the third part, the discussion is extended to elbows under combined pressure and in plane bending moment.« less

Joining dissimilar stainless steels for pressure vessel components

NASA Astrophysics Data System (ADS)

Sun, Zheng; Han, Huai-Yue

1994-03-01

A series of studies was carried out to examine the weldability and properties of dissimilar steel joints between martensitic and austenitic stainless steels - F6NM (OCr13Ni4Mo) and AISI 347, respectively. Such joints are important parts in, e.g. the primary circuit of a pressurized water reactor (PWR). This kind of joint requires both good mechanical properties, corrosion resistance and a stable magnetic permeability besides good weldability. The weldability tests included weld thermal simulation of the martensitic steel for investigating the influence of weld thermal cycles and post-weld heat treatment (PWHT) on the mechanical properties of the heat-affected zone (HAZ); implant testing for examining the tendency for cold cracking of martensitic steel; rigid restraint testing for determining hot crack susceptibility of the multi-pass dissimilar steel joints. The joints were subjected to various mechanical tests including a tensile test, bending test and impact test at various temperatures, as well as slow strain-rate test for examining the stress corrosion cracking tendency in the simulated environment of a primary circuit of a PWR. The results of various tests indicated that the quality of the tube/tube joints is satisfactory for meeting all the design requirements.

Characterization of interfacial reactions and oxide films on 316L stainless steel in various simulated PWR primary water environments

NASA Astrophysics Data System (ADS)

Chen, Junjie; Xiao, Qian; Lu, Zhanpeng; Ru, Xiangkun; Peng, Hao; Xiong, Qi; Li, Hongjuan

2017-06-01

The effect of water chemistry on the electrochemical and oxidizing behaviors of 316L SS was investigated in hydrogenated, deaerated and oxygenated PWR primary water at 310 °C. Water chemistry significantly influenced the electrochemical impedance spectroscopy parameters. The highest charge-transfer resistance and oxide-film resistance occurred in oxygenated water. The highest electric double-layer capacitance and constant phase element of the oxide film were in hydrogenated water. The oxide films formed in deaerated and hydrogenated environments were similar in composition but different in morphology. An oxide film with spinel outer particles and a compact and Cr-rich inner layer was formed in both hydrogenated and deaerated water. Larger and more loosely distributed outer oxide particles were formed in deaerated water. In oxygenated water, an oxide film with hematite outer particles and a porous and Ni-rich inner layer was formed. The reaction kinetics parameters obtained by electrochemical impedance spectroscopy measurements and oxidation film properties relating to the steady or quasi-steady state conditions in the time-period of measurements could provide fundamental information for understanding stress corrosion cracking processes and controlling parameters.

Determination of uncertainties of PWR spent fuel radionuclide inventory based on real operational history data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fast, Ivan; Bosbach, Dirk; Aksyutina, Yuliya

A requisite for the official approval of the safe final disposal of SNF is a comprehensive specification and declaration of the nuclear inventory in SNF by the waste supplier. In the verification process both the values of the radionuclide (RN) activities and their uncertainties are required. Burn-up (BU) calculations based on typical and generic reactor operational parameters do not encompass any possible uncertainties observed in real reactor operations. At the same time, the details of the irradiation history are often not well known, which complicates the assessment of declared RN inventories. Here, we have compiled a set of burnup calculationsmore » accounting for the operational history of 339 published or anonymized real PWR fuel assemblies (FA). These histories were used as a basis for a 'SRP analysis', to provide information about the range of the values of the associated secondary reactor parameters (SRP's). Hence, we can calculate the realistic variation or spectrum of RN inventories. SCALE 6.1 has been employed for the burn-up calculations. The results have been validated using experimental data from the online database - SFCOMPO-1 and -2. (authors)« less

Multidimensional Mixing Behavior of Steam-Water Flow in a Downcomer Annulus During LBLOCA Reflood Phase with a Direct Vessel Injection Mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kwon, Tae-Soon; Yun, Byong-Jo; Euh, Dong-Jin

Multidimensional thermal-hydraulic behavior in the downcomer annulus of a pressurized water reactor (PWR) vessel with a direct vessel injection mode is presented based on the experimental observation in the MIDAS (multidimensional investigation in downcomer annulus simulation) steam-water test facility. From the steady-state test results to simulate the late reflood phase of a large-break loss-of-coolant accident (LBLOCA), isothermal lines show the multidimensional phenomena of a phasic interaction between steam and water in the downcomer annulus very well. MIDAS is a steam-water separate effect test facility, which is 1/4.93 linearly scaled down to a 1400-MW(electric) PWR type of a nuclear reactor, focusedmore » on understanding multidimensional thermal-hydraulic phenomena in a downcomer annulus with various types of safety injection during the refill or reflood phase of an LBLOCA. The initial and the boundary conditions are scaled from the pretest analysis based on the preliminary calculation using the TRAC code. The superheated steam with a superheating degree of 80 K at a given downcomer pressure of 180 kPa is injected equally through three intact cold legs into the downcomer.« less

On-line detection of key radionuclides for fuel-rod failure in a pressurized water reactor.

PubMed

Qin, Guoxiu; Chen, Xilin; Guo, Xiaoqing; Ni, Ning

2016-08-01

For early on-line detection of fuel rod failure, the key radionuclides useful in monitoring must leak easily from failing rods. Yield, half-life, and mass share of fission products that enter the primary coolant also need to be considered in on-line analyses. From all the nuclides that enter the primary coolant during fuel-rod failure, (135)Xe and (88)Kr were ultimately chosen as crucial for on-line monitoring of fuel-rod failure. A monitoring system for fuel-rod failure detection for pressurized water reactor (PWR) based on the LaBr3(Ce) detector was assembled and tested. The samples of coolant from the PWR were measured using the system as well as a HPGe γ-ray spectrometer. A comparison showed the method was feasible. Finally, the γ-ray spectra of primary coolant were measured under normal operations and during fuel-rod failure. The two peaks of (135)Xe (249.8keV) and (88)Kr (2392.1keV) were visible, confirming that the method is capable of monitoring fuel-rod failure on-line. Copyright © 2016 Elsevier Ltd. All rights reserved.

Annual progress report on the NSRR experiments, (21)

NASA Astrophysics Data System (ADS)

1992-05-01

Fuel behavior studies under simulated reactivity-initiated accident (RIA) conditions have been performed in the Nuclear Safety Research Reactor (NSRR) since 1975. This report gives the results of experiments performed from April, 1989 through March, 1990 and discussions of them. A total of 41 tests were carried out during this period. The tests are distinguished into pre-irradiated fuel tests and fresh fuel tests; the former includes 2 JMTR pre-irradiated fuel tests, 2 PWR pre-irradiated fuel tests, and 2 BWR pre-irradiated fuel tests, and the latter includes 6 standard fuel tests (6 SP(center dot)CP scoping tests), 7 power and cooling condition parameter tests (4 flow shrouded fuel tests, 1 bundle simulation test, 1 fully water-filled vessel test, 1 high pressure/high temperature loop test), 12 special fuel tests (3 stainless steel clad fuel tests, 3 improved PWR fuel tests, 6 improved BWR fuel tests), 3 severe fuel damage tests (1 high temperature flooding test, 1 flooding behavior observation test, 1 debris coolability test), 3 fast breeder reactor fuel tests (2 moderator material characteristic measurement tests, 1 fuel behavior observation test), and 2 miscellaneous tests (2 preliminary tests for pre-irradiated fuel tests).

PRESSURIZED WATER REACTOR (PWR) PROJECT TECHNICAL PROGRESS REPORT FOR THE PERIOD DECEMBER 24, 1959 TO FEBRUARY 23, 1960

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

< 9 A < 2 6 < 7 4 8 9 6 2 6 equalizing vent valves on air locks 2, 4, and 5 was completed. An evaluation of the failed main coolant pump No. 1-80-F-737 was completed. The design for installing combination ball check and manual stop valves on the boiler water level sight glasses, to prevent the escape of steam should a defective sight glass develop, was completed. The main coolant pumps No. 80 and No. 79 were modified by increasing the radial clearance of the impeller wear ring and by removing the upper labyrinth ring. A designmore » for relocating the cooling water flow orifice 17-J4-17 was completed. Metallurgy: Preliminary data from the Bett 69-1 in-pile thermal conductivity capsules indicate that the thermal conductivity of as-sintered ZrO/sub 2/ 34 wt.% UO/sub 2/ appears to decrease from an initial value of about 1.6 Btu/hr-ft- deg F to about 0.7 Btu/hr-ft- deg F after 17 days irradiation in an estimated perturbed flux of 4 x 10/sup 13/. The thermal conductivities of UO/sub 2/ and BeO 51 wt.% UO/sub 2/ fuel remained unchanged during this time. Examination of the two failed X-3-1 fuel plates and the two failed CR-V-m fuel plates showed that a definite burnup limitation exists for bulk UO/sub 2/i of about 16 x 10/sup 20/ to 21.5 x 10/sup 20/ fissions/cc at which point the fuel increases in volume about 4- -5%. Irradiation of both fine and coarse dis-persions of 28 wt.% UO/sub 2/in BeO to exposures of about 11 x 10/sup 20/ fissions/cc shows this material has very poor dimensional stabllity and poor fission gas retention ability. The fine particles dispersion showed approximately 4.8 times the thickness increase as did the coarse particles. Interim examination of a bulk B/sub 4/ burnable poison plate irradiated in the HB-1 loop to about 60 at.% B/sup 10/ burnup showed a 17% increase in plate thickness. The technical feasibility of fabricating blanket receptacles with full length fuel channels and an integral cover plate by form rolling was established. Hack-pressure-bonding appears to be a suitable means of incorporating void volume in fuel compartments of oxide plates. High density (99% T.D.) and improved microstructure of B/sub 4/C-SiC burnable poisons are achieved when small (2 micron) B/sub 4/C particle size powder is used ia hot pressing compacts. Measurements of the self-diffusion coefficients of uranium in UO/sub 2/ by the method of surface activity decrease were completed. Experiments on the diffusion of Xe/sup 133/ in Core 2--type UO/sup 2/ fuel platelets were completed. Diffusion anaeals carried out at 1000 deg C on samples from the X-3-1 and the 14-28 irradiation tests show that the apparent diffusion coefficient for Kr/sup 85/ incresses considerably with burnup. An average activation energy for thoron emanation in UO/sub 2/ was estimated to be 44 kcal/mole. An initial experiment on the release of helium from slightly irradiated B/sub 4/C at 900 deg C resulted in a diffusion coefficient for helium of 3.5 x 10/sup -8/ Physics: Calculatad values for seed-blanket power sharing as a function of PWR-1 Seed 1 life were compared with measured data obtained from thermal instrumentation at Shippingport. Two-dimensional depletion studies in the PWR-2 "composite cell" geometry were completed for seed assembly configurations having different radial fuel zoning. An eighth core representation is being employed for a two- dimensional depletion calculation of PWR-2. An analysis of the effect on the axial power distribution of the nonuniform temperature distribution in an 8 ft PWR-2 core loaded with 295 kg of U/sup 235/ indicated that local variations in power density of as much as 15% may occur, relative to the distribution that would exist if the axial temperature distribution were uniform. A technique was developed which makes possible an approximately correct description of the neutron capture rate within small rectangular boron wafers in diffusion theory calculations. Seed peaking factors measured in a five-cluster slab of PWR-2 mock- up materials were measured and compared with calculated peaking factors obtained using the nuclear« less

REDUCTIVE DEHALOGENATION OF HEXACHLOROETHANE, CARBON TETRACHLORIDE, AND BROMOFORM BY ANAHYDROQUINONE DISULFONATE AND HUMIC ACID

EPA Science Inventory

The reductive dehalogenation of hexachloroethane (C2CI6), carbon tetrachloride (CC14), and bromoform (CHBr3) was examined at 50 degrees C in aqueous solutions containing either (1) 500 uM of 2,6-anthrahydroquinone disulfonate (AHQDS), (2) 250 uM Fe2+, or (3) 250 uM HS. The pH ran...

Assessment of Teams and Teamwork in the University of Maryland Libraries

ERIC Educational Resources Information Center

Baughman, M. Sue

2008-01-01

Teams play an important role in the University of Maryland (UM) Libraries. Since 1998, teams and collaborative teamwork have become the way librarians address the myriad of issues affecting the needs of UM's faculty, students, and staff. There has been much change in the UM Libraries over the past nine years, and the development is ongoing.…

Somatic embryogenesis in immature cotyledons of Manchurian ash (Fraxinus mandshurica Rupr.)

USDA-ARS?s Scientific Manuscript database

Somatic embryogenesis was obtained from immature cotyledon explants that were cultured on half-strength Murashige and Skoog (MS) salts and vitamins with 5.4 uM naphthaleneacetic acid (NAA) and 0.2 uM thidiazuron (TDZ) plus a 4x4 factorial combination of 0,9.8, 34.6, or 49.2 uM indole-3-butyric acid ...

VizieR Online Data Catalog: Young clumps embedded in IRDC (Traficante+, 2015)

NASA Astrophysics Data System (ADS)

Traficante, A.; Fuller, G. A.; Peretto, N.; Pineda, J. E.; Molinari, S.

2015-06-01

Photometric parameters for 667 starless clumps (sources identified at 160um with a counterpart at 250 and 350um) and 1056 protostellar clumps (sources identified at 160um with a counterpart at 70, 250 and 350um). Photometric parameters obtained with Hyper photometry code (2015A&A...574A.119T). The photometry is corrected for aperture and colour corrections. The parameter list is the standard Hyper output (see description below). SED fit parameters for 650 starless clumps and 1034 protostellar clumps (all clumps with good SED fitting: Chi2<10, Temperature<40K. See the paper for details) (4 data files).

VizieR Online Data Catalog: Draco nebula Herschel 250um map (Miville-Deschenes+, 2017)

NASA Astrophysics Data System (ADS)

Miville-Deschenes, M.-A.; Salome, Q.; Martin, P. G.; Joncas, G.; Blagrave, K.; Dassas, K.; Abergel, A.; Beelen, A.; Boulanger, F.; Lagache, G.; Lockman, F. J.; Marshall, D. J.

2017-03-01

Draco was observed with Herschel PACS (110 and 170um) and SPIRE (250, 350 and 500um) as part of the open-time program "First steps toward star formation: unveiling the atomic to molecular transition in the diffuse interstellar medium" (P.I. M-A Miville-Deschenes). A field of 3.85x3.85 was observed in parallel mode. Unfortunately, an error occurred during the acquisition of the PACS data making them unusable. Therefore, the results presented here are solely based on SPIRE data, especially the 250um map that has the highest angular resolution. (2 data files).

High Frequency GaAs Bulk Acousto-Optic Devices For Modulators And Frequency Shifters At 1.3um And 1.5um In Fiber-Optics

NASA Astrophysics Data System (ADS)

Soos, J. I.; Rosemeier, R. G.

1989-02-01

The edge of a transmission window for a GaAs Bragg cell starts about lum, which allows this material to be used for infrared fiber-optic applications, especially at 1.3um and 1.5um. The single crystal of GaAs is acoustically anisotropic and has the highest figure of merit, M2, along <111> direction for a longitudinal mode sound wave. Recently, Brimrose has designed and fabricated an acousto-optic modulator from GaAs operating at a carrier frequency of 2.3 GHz with a diffraction efficiency of 4%/RF watt.

VizieR Online Data Catalog: LRLL54361 protostar Herschel/PACS fluxes (Balog+, 2014)

NASA Astrophysics Data System (ADS)

Balog, Z.; Muzerolle, J.; Flaherty, K.; Detre, O. H.; Bouwmann, J.; Furlan, E.; Gutermuth, R.; Juhasz, A.; Bally, J.; Nielbock, M.; Klaas, U.; Krause, O.; Henning, T.; Marton, G.

2017-03-01

We observed a 14'x14' area in IC348 with the Photodetector Array Camera and Spectrometer (PACS; Poglitsch et al. 2010A&A...518L...2P) Herschel Space Observatory (Pilbratt et al. 2010A&A...518L...1P) simultaneously at 70 and 160um 24 times in scan map mode. An additional five epoch were observed during a later pulse phase of LRLL54361 in all three PACS photometer bands. The PACS spectrograph consists of a 5x5 array of 9.4" x 9.4" spatial pixels (hereafter referred to as spaxels) covering the spectral range from 52-210 um with λ/δλ ~1000-3000. Spectra were obtained in two spectral orders simultaneously, with the second order ranging from 51 to 105um and the first order from 102 to 210um. The spatial resolution of PACS-S ranges from ~9'' at 50um to ~18'' at 210um. Our target was observed in the standard range-scan spectroscopy mode with a grating step size corresponding to Nyquist sampling (see further Poglitsch et al. 2010A&A...518L...2P). (1 data file).

[Estimation of uncertainty of measurement in clinical biochemistry].

PubMed

Enea, Maria; Hristodorescu, Cristina; Schiriac, Corina; Morariu, Dana; Mutiu, Tr; Dumitriu, Irina; Gurzu, B

2009-01-01

The uncertainty of measurement (UM) or measurement uncertainty is known as the parameter associated with the result of a measurement. Repeated measurements usually reveal slightly different results for the same analyte, sometimes a little higher, sometimes a little lower, because the results of a measurement are depending not only by the analyte itself, but also, by a number of error factors that could give doubts about the estimate. The uncertainty of the measurement represent the quantitative, mathematically expression of this doubt. UM is a range of measured values which is probably to enclose the true value of the measured. Calculation of UM for all types of laboratories is regularized by the ISO Guide to the Expression of Uncertainty in Measurement (abbreviated GUM) and the SR ENV 13005 : 2003 (both recognized by European Accreditation). Even if the GUM rules about UM estimation are very strictly, the offering of the result together with UM will increase the confidence of customers (patients or physicians). In this study the authors are presenting the possibilities of UM assessing in labs from our country by using the data obtained in the procedures of methods validation, during the internal and external quality control.

VizieR Online Data Catalog: Spectrophotometric distances of HII regions (Moises+, 2011)

NASA Astrophysics Data System (ADS)

Moises, A. P.; Damineli, A.; Figueredo, E.; Blum, R. D.; Conti, P. S.; Barbosa, C. L.

2011-11-01

The J-band (λ1.28um, δλ=0.3um), H-band (λ1.63um, δλ=0.3um) and Ks-band (λ2.19um, δλ=0.4um) images were obtained on the nights of 1999 May 1, 4 and 20, 2000 May 19 and 21 and 2001 July 10 and 12, at the Cerro Tololo Inter-American Observatory (CTIO) 4-m Blanco telescope, using the facility's infrared imager OSIRIS, which has a field of view (FOV) of 93x93arcsec2 and a pixel scale of 0.161arcsec/pixel. On the nights of 2005 Jult 3-6 and 11 and 2006 June 3-7, we obtained images using the facility's infrared imager ISPI (with a FOV of 10.25x10.25arcmin2 and a pixel scale of 0.3arcsec/pix), also at the 4-m Blanco telescope. Also, on the nights of 1998 August 28 and 29, we obtained images on the CTIO 4-m telescope using the facility's infrared imager CIRIM (with a FOV of 102x102arcsec2 and a pixel scale of 0.40arcsec/pix). (3 data files).

Unconsummated marriage: can it still be considered a consequence of vaginismus?

PubMed

Michetti, P M; Silvaggi, M; Fabrizi, A; Tartaglia, N; Rossi, R; Simonelli, C

2014-01-01

Unconsummated marriage (UM) is the failure to perform successful sexual intercourse at the beginning of the marriage. Vaginismus has been traditionally reported as the leading cause. ED is also a leading cause for UM. This appears to be a significant problem in the conservative middle-Eastern societies and in the developing countries, where couples are strongly prevented by religious rules and cultural taboos from sexual experiences before wedding. One could think that according to major sexual freedom and information, in Western countries UM is now disappearing, but the number of observed cases by the authors in 2008-2012 was relevant. The aim of this study is to compare the literature data from non-Western countries with the features of UM in Western ones, focusing on cases observed by the authors, and to verify whether the etiology of UM proposed in the '70s is still relevant, outlining any changes that occur in current reality. In our series, traditional appearance of UM is no more effective, while the role of man is undervalued, because of his frailty, lack of self-confidence and ignorance, expressing a social and cultural change of man's role in the couple.

Elucidating the role of the FoxO3a transcription factor in the IGF-1-induced migration and invasion of uveal melanoma cancer cells.

PubMed

Yan, Fengxia; Liao, Rifang; Farhan, Mohd; Wang, Tinghuai; Chen, Jiashu; Wang, Zhong; Little, Peter J; Zheng, Wenhua

2016-12-01

Uveal melanoma (UM) is the most common primary intraocular malignant tumor of adults. It has high mortality rate due to liver metastasis. However, the epidemiology and pathogenesis of liver metastasis in UM are not elucidated and there is no effective therapy available for preventing the development of this disease. IGF-1 is a growth factor involved in cell proliferation, malignant transformation and inhibition of apoptosis. In previous report, IGF-1 receptor was found to be highly expressed in UM and this was related to tumor prognosis. FoxO3a is a Forkhead box O (FOXO) transcription factor and a downstream target of the IGF-1R/PI3K/Akt pathway involved in a number of physiological and pathological processes including cancer. However, the role of FoxO3a in UM is unknown. In the present study, we investigated fundamental mechanisms in the growth, migration and invasion of UM and the involvement of FoxO3a. IGF-1 increased the cell viability, invasion, migration and S-G2/M cell cycle phase accumulation of UM cells. Western blot analysis showed that IGF-1 led to activation of Akt and concomitant phosphorylation of FoxO3a. FoxO3a phosphorylation was associated with its translocation into the cytoplasm from the nucleus and its functional inhibition led to the inhibition of expression of Bim and p27, but an increase in the expression of Cyclin D1. The effects of IGF-1 on UM cells were reversed by LY294002 (a PI3K inhibitor) or Akt siRNA, and the overexpression of FoxO3a also attenuated basal invasion and migration of UM. Taken all together, these results suggest that inhibition of FoxO3a by IGF-1 via the PI3K/Akt pathway has an important role in IGF-1 induced proliferation and invasion of UM cells. These findings also support FoxO3a and IGF signaling may represent a valid target for investigating the development of new strategies for the treatment and prevention of the pathology of UM. Copyright © 2016. Published by Elsevier Masson SAS.

Undermethylated DNA as a source of microsatellites from a conifer genome.

PubMed

Zhou, Y; Bui, T; Auckland, L D; Williams, C G

2002-02-01

Developing microsatellites from the large, highly duplicated conifer genome requires special tools. To improve the efficiency of developing Pinus taeda L. microsatellites, undermethylated (UM) DNA fragments were used to construct a microsatellite-enriched copy library. A methylation-sensitive restriction enzyme, McrBC, was used to enrich for UM DNA before library construction. Digested DNA fragments larger than 9 kb were then excised and digested with RsaI and used to construct nine dinucleotide and trinucleotide libraries. A total of 1016 microsatellite-positive clones were detected among 11 904 clones and 620 of these were unique. Of 245 primer sets that produced a PCR product, 113 could be developed as UM microsatellite markers and 70 were polymorphic. Inheritance and marker informativeness were tested for a random sample of 36 polymorphic markers using a three-generation outbred pedigree. Thirty-one microsatellites (86%) had single-locus inheritance despite the highly duplicated nature of the P. taeda genome. Nineteen UM microsatellites had highly informative intercross mating type configurations. Allele number and frequency were estimated for eleven UM microsatellites using a population survey. Allele numbers for these UM microsatellites ranged from 3 to 12 with an average of 5.7 alleles/locus. Frequencies for the 63 alleles were mostly in the low-common range; only 14 of the 63 were in the rare allele (q < 0.05) class. Enriching for UM DNA was an efficient method for developing polymorphic microsatellites from a large plant genome.

VizieR Online Data Catalog: UKIDSS-DR8 LAS, GCS and DXS Surveys (Lawrence+ 2012)

NASA Astrophysics Data System (ADS)

Lawrence, A.; Warren, S. J.; Almaini, O.; Edge, A. C.; Hambly, N. C.; Jameson, R. F.; Lucas, P.; Casali, M.; Adamson, A.; Dye, S.; Emerson, J. P.; Foucaud, S.; Hewett, P.; Hirst, P.; Hodgkin, S. T.; Irwin, M. J.; Lodieu, N.; McMahon, R. G.; Simpson, C.; Smail, I.; Mortlock, D.; Folger, M.

2012-03-01

The UKIRT Infrared Deep Sky Survey (UKIDSS) is a large-scale near-IR survey which aim is to cover 7500 square degrees of the Northern sky. The survey is carried out using the Wide Field Camera (WFCAM), with a field of view of 0.21 square degrees, mounted on the 3.8m United Kingdom Infra-red Telescope (UKIRT) in Hawaii. The project comprises five surveys (LAS, GCS, DXS, GPS and UDS). The Large Area Survey (LAS) covers an area of 4000 square degrees in high Galactic latitudes (extragalactic) in the four bands Y(1.0um) J(1.2um) H(1.6um) and K(2.2um) to a depth of K=18.4. The Galactic Clusters Survey (GCS) aims to survey ten large open star clusters and star formation associations, covering a total of 1067 square degrees in the five bands Z (0.9um), Y(1.0um) J(1.2um) H(1.6um) and K(2.2um), plus a second pass in K for proper motions, to a depth of Z=20.4, Y=20.3, J=19.5, H=18.6, K=18.6. The Deep Extragalactic Survey (DXS) aims to map 35 square degrees of sky to a 5-σ point-source sensitivity of J=22.3 and K=20.8 in four carefully selected, multi-wavelength survey areas. The central regions of each field will also be mapped to H=21.8. The primary aim of the survey is to produce a photometric galaxy sample at a redshift of 1-2, within a volume comparable to that of the SDSS, selected in the same passband (rest frame optical). Details of the surveys can be found in the in the paper by Lawrence et al. (2007MNRAS.379.1599L), and at the UKIDSS Surveys site (http://www.ukidss.org/surveys/surveys.html). The data described here represent a subset of the UKIDSS data, limited to the public data and most representative columns. In the "Byte-by-byte Description" below the original names of the columns are given as bracketed names. (3 data files).

Study on extrusion process of SiC ceramic matrix

NASA Astrophysics Data System (ADS)

Dai, Xiao-Yuan; Shen, Fan; Ji, Jia-You; Wang, Shu-Ling; Xu, Man

2017-11-01

In this thesis, the extrusion process of SiC ceramic matrix has been systematically studied.The effect of different cellulose content on the flexural strength and pore size distribution of SiC matrix was discussed.Reselts show that with the increase of cellulose content, the flexural strength decreased.The pore size distribution in the sample was 1um-4um, and the 1um-2um concentration was more concentrated. It is found that the cellulose content has little effect on the pore size distribution.When the cellulose content is 7%, the flexural strength of the sample is 40.9Mpa. At this time, the mechanical properties of the sample are the strongest.

Study and optimization of the macroscopic electrical response of carbon based nanocomposites for advanced applications

NASA Astrophysics Data System (ADS)

Silva, Jaime Pedro Oliveira da

A presente tese centrou-se no estudo da resposta da constante dieletrica e condutividade eletrica em materiais compositos nos quais o reforco tinha uma elevada proporcao entre comprimento e diametro. O objeto de estudo foi o efeito de um reforco com uma elevada razao entre comprimento e diametro, concentracao e orientacao na resposta eletrica e dieletrica de um composito. Estes compositos tem uma grande importancia no desenvolvimento de materiais para sensores e atuadores. Num primeiro momento da dissertacao, explorou-se a resposta da constante dieletrica de um composito constituido por nanotubos de carbono como reforco e uma matriz polimerica. Verificou-se que um aumento da razao entre comprimento e diametro do reforco tem o efeito de aumentar a constante dieletrica do composito para uma igual fracao volumetrica de reforco. Constatou-se tambem que materiais na fase nematica demonstram uma constante dieletrica mais baixa quando comparados com materiais onde o reforco esta distribuido aleatoriamente. Ficou ainda demonstrado nesta dissertacao que materiais na fase nematica com razoes entre o comprimento e diametro diferentes a constante dieletrica segue uma lei de potencia. Numa segunda fase do trabalho, foi explorada a condutividade de nanocompositos polimericos reforcados com nanotubos de carbono, atraves de um modelo baseado em cilindros impenetraveis. Ficou demonstrado que o modelo e apropriado para descrever a condutividade eletrica de um nanocomposito polimerico reforcado com nanotubos. As simulacoes desenvolvidas demonstram que, aumentando a razao entre o comprimento e o diametro dos nanotubos de carbono, aumenta a condutividade eletrica do nanocomposito. No entanto, verifica-se que aumentando a anisotropia diminui a condutividade, sendo este efeito mais evidente para fracoes volumetricas maiores. Nesta dissertacao comprovou-se ainda que uma microestrutura gerada por um algoritmo de empacotamento sequencial pode ser descrita por um grafo aleatorio e que a condutividade num composito reforcado com nanofibras de carbono pode ser descrito por uma rede de Bethe. Atraves do uso da teoria das redes complexas, chegou-se a uma expressao para o limite de percolacao e, do mesmo modo, demonstrou-se que “hopping” entre fibras adjacentes resulta numa expressao que corresponde a um regime de desordem fraca. No trabalho desenvolvido tambem foi calculado os expoentes criticos, atraves da teoria das redes, para um sistema 3D composto por cilindros impenetraveis com uma interacao de curto alcance, demonstrando que os expoentes criticos estao relacionados por uma relacao de hiperescala comum para 3D e nao pertencem a mesma classe de universalidade como a percolacao numa rede. A aplicacao do modelo desenvolvido a compositos de epoxy reforcada, com diferentes metodos de dispersao de nanofibras de carbono, revelou que os metodos de dispersao usados para preparar os compositos tem uma forte influencia nas propriedades eletricas que podem ser capturadas pelo modelo. Neste contexto, ficou ainda demonstrado que a condutividade eletrica pode ser descrita por um regime de desordem fraca, isto ´e, um regime onde todas as conexoes fibra-fibra participam na condutividade do composito. O modelo desenvolvido foi aplicado igualmente a compositos de poly (vinylidene fluoride) reforcado com nanotubos de carbono com diferentes tratamentos de termicos de oxidacao. Verificou-se que os tratamentos de superficie aumentam o limite de percolacao e diminuem a condutividade. Nesta dissertacao provamos ainda que a condutividade do composito pode ser atribuida a um mecanismo de “hopping”, fortemente afetado pelos tratamentos de superficie dos reforcos.

Modulation of GABA-stimulated chloride influx into membrane vesicles from rat cerebral cortex by triazolobenzodiazepines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Obata, T.; Yamamura, H.I.

1988-01-01

The effects of triazolobenzodiazepines of GABA-stimulated /sup 36/Cl/sup -/ uptake by membrane vesicles from rat cerebral cortex were examined. Triazolam and alprazolam showed a significant enhancement of GABA-stimulated /sup 36/Cl/sup -/ uptake at 0.01-10 uM. On the other hand, adinazolam showed a small enhancement at 0.1-1 uM followed by a significant inhibition of GABA-stimulated /sup 36/Cl/sup -/ uptake at 100 uM. The enhancement of GABA-stimulated /sup 36/Cl/sup -/ uptake by 1 uM alprazolam was antagonized by Ro15-1788, a benzodiazepine antagonist, but the inhibition of this response by 30 uM adinazolam was not antagonized by Ro15-1788. These results indicate that triazolobenzodiazepinesmore » enhanced GABA-stimulated /sup 36/Cl/sup -/ uptake through benzodiazepine receptors. High concentrations of adinazolam inhibit GABA-stimulated /sup 36/Cl/sup -/ uptake which may be due to the direct blockade of GABA-gated chloride channel. 23 references, 4 figures.« less

Selumetinib-based therapy in uveal melanoma patient-derived xenografts

PubMed Central

Decaudin, Didier; El Botty, Rania; Diallo, Béré; Massonnet, Gerald; Fleury, Justine; Naguez, Adnan; Raymondie, Chloé; Davies, Emma; Smith, Aaron; Wilson, Joanne; Howes, Colin; Smith, Paul D.; Cassoux, Nathalie; Piperno-Neumann, Sophie; Roman-Roman, Sergio; Némati, Fariba

2018-01-01

The prognosis of metastatic uveal melanoma (UM) is among the worst of all human cancers. The identification of near-ubiquitous GNAQ/GNA11 mutations and the activation of MAPK signaling in UM have raised hopes of more effective, targeted therapies, based on MEK inhibition, for example. We evaluated the potential of drug combinations to increase the efficacy of the MEK inhibitor selumetinib (AZD6244, ARRY-142886), in UM cell lines and Patient-Derived Xenografts. We first evaluated the combination of selumetinib and DTIC. We found that DTIC did not improve the in vitro or in vivo antitumor efficacy of selumetinib, consistent with the outcome of the SUMIT clinical trial assessing the efficacy of this combination in UM. We then tested additional selumetinib combinations with the chemotherapy agent docetaxel, the ERK inhibitor AZ6197, and the mTORC1/2 inhibitor, vistusertib (AZD2014). Combinations of selumetinib with ERK and mTORC1/2 inhibitors appeared to be the most effective in UM PDX models. PMID:29774094

Immunostaining, dehydration, and clearing of mouse embryos for ultramicroscopy.

PubMed

Becker, Klaus; Jährling, Nina; Saghafi, Saiedeh; Dodt, Hans-Ulrich

2013-08-01

This protocol describes the preparation of mouse embryos for ultramicroscopy (UM), a powerful imaging technique that achieves precise and accurate three-dimensional (3D) reconstructions of intact macroscopic specimens with micrometer resolution. In UM, a specimen in the size range of ∼1-15 mm is illuminated perpendicular to the observation pathway by two thin counterpropagating sheets of laser light. In combination with fluorescein isothiocyanate (FITC) immunostaining, UM allows visualization of somatic motor and sensorial nerve fibers in whole mouse embryos. Even the fine branches of the sensomotoric fibers can be visualized over a distance of up to several millimeters. In this protocol, mouse embryos are fixed and immunostained in preparation for UM. Because UM requires the excitation light sheet to travel throughout the entire horizontal width of the specimen, specimens usually have to be rendered transparent before microscope inspection. Here, the embryos are dehydrated in ethanol and then cleared in a solution of benzyl alcohol and benzyl benzoate.

The mental health of unaccompanied refugee minors on arrival in the host country.

PubMed

Vervliet, Marianne; Meyer Demott, Melinda A; Jakobsen, Marianne; Broekaert, Eric; Heir, Trond; Derluyn, Ilse

2014-02-01

Despite increasing numbers of unaccompanied refugee minors (UM) in Europe and heightened concerns for this group, research on their mental health has seldom included the factor "time since arrival." As a result, our knowledge of the mental health statuses of UM at specific points in time and over periods in their resettlement trajectories in European host countries is limited. This study therefore examined the mental health of UM shortly after their arrival in Norway (n = 204) and Belgium (n = 103) through the use of self-report questionnaires (HSCL-37A, SLE, RATS, HTQ). High prevalence scores of anxiety, depression and posttraumatic stress disorder (PTSD) symptoms were found. In addition, particular associations were found with the number of traumatic events the UM reported. The results indicate that all UM have high support needs on arrival in the host country. Longitudinal studies following up patterns of continuity and change in their mental health during their trajectories in the host country are necessary. © 2014 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

Driving bubbles out of glass

NASA Technical Reports Server (NTRS)

Mattox, D. M.

1981-01-01

Surface tension gradient in melt forces gas bubbles to surface, increasing glass strength and transparency. Conventional chemical and buoyant fining are extremely slow in viscous glasses, but tension gradient method moves 250 um bubbles as rapidly as 30 um/s. Heat required for high temperature part of melt is furnished by stationary electrical or natural-gas heater; induction and laser heating are also possible. Method has many applications in industry processes.

10 CFR 50.75 - Reporting and recordkeeping for decommissioning planning.

Code of Federal Regulations, 2010 CFR

2010-01-01

... investing or otherwise, that a prudent investor would use in the same circumstances. The term “prudent... than or equal to 3400 MWt $105 between 1200 MWt and 3400 MWt (For a PWR of less than 1200 MWt, use P... 3400 MWt (For a BWR of less than 1200 MWt, use P=1200 MWt) $(104+0.009P) (2) An adjustment factor at...

Experimental and Analytical Development of the Application of a Transit Laser Velocimeter

DTIC Science & Technology

1980-11-01

from 0.005" brass shim stock with carefully finished edges and chemically blackened surface and is slightly adjustable in position to compensate for...personnel by Mr. T. V. C i e l , ETF . Mr. V i r g i l Cline, PWr, and t h e f a c i l i t y technic ians . A 1" diameter underexpanded unheated

40 CFR 59.507 - What are the labeling requirements for aerosol coatings?

Code of Federal Regulations, 2010 CFR

2010-07-01

... in Table 1 of this subpart or a company-specific code, if that code is explained as required by § 59.511(a); (2) The applicable PWR limit for the product specified in Table 1 of this subpart; (3) The day... this subpart. (b) The label on the product must be displayed in such a manner that it is readily...

Analysis of Coolant Options for Advanced Metal Cooled Nuclear Reactors

DTIC Science & Technology

2006-12-01

24 Table 3.3 Hazards of Sodium Reaction Products, Hydride And Oxide...........................26 Table 3.4 Chemical Reactivity Of Selected...Liquid Metal Fast Breeder Reactor ORIGEN Oak Ridge Isotope Generator ORIGENARP Oak Ridge Isotope Generator Automated Rapid Processing PWR ...nuclear reactors, both because of the possibility of increased reactivity due to boiling and the potential loss of effectiveness of coolant heat transfer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vidal, Jean-Marc; Eschbach, Romain; Launay, Agnes

CEA and AREVA-NC have developed and used a depletion code named CESAR for 30 years. This user-friendly industrial tool provides fast characterizations for all types of nuclear fuel (PWR / UOX or MOX or reprocess Uranium, BWR / UOX or MOX, MTR and SFR) and the wastes associated. CESAR can evaluate 100 heavy nuclides, 200 fission products and 150 activation products (with Helium and Tritium formation). It can also characterize the structural material of the fuel (Zircalloy, stainless steel, M5 alloy). CESAR provides depletion calculations for any reactor irradiation history and from 3 months to 1 million years of coolingmore » time. CESAR5.3 is based on the latest calculation schemes recommended by the CEA and on an international nuclear data base (JEFF-3.1.1). It is constantly checked against the CEA referenced and qualified depletion code DARWIN. CESAR incorporates the CEA qualification based on the dissolution analyses of fuel rod samples and the 'La Hague' reprocessing plant feedback experience. AREVA-NC uses CESAR intensively at 'La Hague' plant, not only for prospective studies but also for characterizations at different industrial facilities all along the reprocessing process and waste conditioning (near 150 000 calculations per year). CESAR is the reference code for AREVA-NC. CESAR is used directly or indirectly with other software, data bank or special equipment in many parts of the La Hague plants. The great flexibility of CESAR has rapidly interested other projects. CESAR became a 'tool' directly integrated in some other softwares. Finally, coupled with a Graphical User Interface, it can be easily used independently, responding to many needs for prospective studies as a support for nuclear facilities or transport. An English version is available. For the principal isotopes of U and Pu, CESAR5 benefits from the CEA experimental validation for the PWR UOX fuels, up to a burnup of 60 GWd/t and for PWR MOX fuels, up to 45 GWd/t. CESAR version 5.3 uses the CEA reference calculation codes for neutron physics with the JEFF-3.1.1 nuclear data set. (authors)« less

The benefits of a fast reactor closed fuel cycle in the UK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gregg, R.; Hesketh, K.

2013-07-01

The work has shown that starting a fast reactor closed fuel cycle in the UK, requires virtually all of Britain's existing and future PWR spent fuel to be reprocessed, in order to obtain the plutonium needed. The existing UK Pu stockpile is sufficient to initially support only a modest SFR 'closed' fleet assuming spent fuel can be reprocessed shortly after discharge (i.e. after two years cooling). For a substantial fast reactor fleet, most Pu will have to originate from reprocessing future spent PWR fuel. Therefore, the maximum fast reactor fleet size will be limited by the preceding PWR fleet size,more » so scenarios involving fast reactors still require significant quantities of uranium ore indirectly. However, once a fast reactor fuel cycle has been established, the very substantial quantities of uranium tails in the UK would ensure there is sufficient material for several centuries. Both the short and long term impacts on a repository have been considered in this work. Over the short term, the decay heat emanating from the HLW and spent fuel will limit the density of waste within a repository. For scenarios involving fast reactors, the only significant heat bearing actinide content will be present in the final cores, resulting in a 50% overall reduction in decay energy deposited within the repository when compared with an equivalent open fuel cycle. Over the longer term, radiological dose becomes more important. Total radiotoxicity (normalised by electricity generated) is lower for scenarios with Pu recycle after 2000 years. Scenarios involving fast reactors have the lowest radiotoxicity since the quantities of certain actinides (Np, Pu and Am) eventually stabilise. However, total radiotoxicity as a measure of radiological risk does not account for differences in radionuclide mobility once in repository. Radiological dose is dominated by a small number of fission products so is therefore not affected significantly by reactor type or recycling strategy (since the fission product will primarily be a function of nuclear energy generated). However, by reprocessing spent fuel, it is possible to immobilise the fission product in a more suitable waste form that has far more superior in-repository performance. (authors)« less

Development of Hplc Techniques for the Analysis of Trace Metal Species in the Primary Coolant of a Pressurised Water Reactor.

NASA Astrophysics Data System (ADS)

Barron, Keiron Robert Philip

Available from UMI in association with The British Library. The need to monitor corrosion products in the primary circuit of a pressurised water reactor (PWR), at a concentration of 10pg ml^{-1} is discussed. A review of trace and ultra-trace metal analysis, relevant to the specific requirements imposed by primary coolant chemistry, indicated that high performance liquid chromatography (HPLC), coupled with preconcentration of sample was an ideal technique. A HPLC system was developed to determine trace metal species in simulated PWR primary coolant. In order to achieve the desired detection limit an on-line preconcentration system had to be developed. Separations were performed on Aminex A9 and Benson BC-X10 analytical columns. Detection was by post column reaction with Eriochrome Black T and Calmagite Linear calibrations of 2.5-100ng of cobalt (the main species of interest), were achieved using up to 200ml samples. The detection limit for a 200ml sample was 10pg ml^{-1}. In order to achieve the desired aim of on-line collection of species at 300^circ C, the use of inorganic ion-exchangers is essential. A novel application, utilising the attractive features of the inorganic ion-exchangers titanium dioxide, zirconium dioxide, zirconium arsenophosphate and pore controlled glass beads, was developed for the preconcentration of trace metal species at temperature and pressure. The performance of these exchangers, at ambient and 300^ circC was assessed by their inclusion in the developed analytical system and by the use of radioisotopes. The particular emphasis during the development has been upon accuracy, reproducibility of recovery, stability of reagents and system contamination, studied by the use of radioisotopes and response to post column reagents. This study in conjunction with work carried out at Winfrith, resulted in a monitoring system that could follow changes in coolant chemistry, on deposition and release of metal species in simulated PWR water loops. On -line detection of cobalt at 11pg ml^{ -1} was recorded, something which previously could not be performed by other techniques.

Genetic heterogeneity in uveal melanoma assessed by multiplex ligation-dependent probe amplification.

PubMed

Dopierala, Justyna; Damato, Bertil E; Lake, Sarah L; Taktak, Azzam F G; Coupland, Sarah E

2010-10-01

To determine intratumor genetic heterogeneity in uveal melanoma (UM) by multiplex ligation-dependent probe amplification (MLPA) in formalin-fixed, paraffin-embedded (FFPE) tumor tissues. DNA was extracted from whole tumor sections and from two to nine different areas microdissected from 32 FFPE UMs. Thirty-one loci on chromosomes 1, 3, 6, and 8 were tested with MLPA for copy number changes. The tumor was considered heterogeneous at a locus if (1) the difference in dosage quotients (DQs) of any two areas was 0.2 or more, and (2) the DQs of the areas belonged to different ranges. Comparison of MLPA data obtained from microdissected areas of the UMs showed heterogeneity in 1 to 26 examined loci in 24 (75%) tumors, with only 25% of the tumors being homogeneous. Intratumor heterogeneity of 3p12.2, 6p21.2, and 8q11.23 was most common, occurring in >30% of the UMs. Gains of chromosome 3 were observed in four UMs, with three of these tumors showing the highest degree of heterogeneity. Copy number variation was associated with differences in tumor cell type, but not with differences in tumor pigmentation or reactive inflammation. UMs with genetic heterogeneity across multiple sample sites showed equivocal MLPA results when the whole tumor section was examined. These results suggest that different clones dilute MLPA results. Heterogeneity of chromosomal abnormalities of chromosomes 1, 3, 6, and 8 is present in most UMs. This heterogeneity causes equivocal MLPA results. One random tumor sample may not be representative of the whole tumor and, therefore, may be insufficient for prognostic testing.

Genomic insight into pathogenicity of dematiaceous fungus Corynespora cassiicola

PubMed Central

Looi, Hong Keat; Toh, Yue Fen; Yew, Su Mei; Na, Shiang Ling; Tan, Yung-Chie; Chong, Pei-Sin; Khoo, Jia-Shiun; Yee, Wai-Yan; Ng, Kee Peng

2017-01-01

Corynespora cassiicola is a common plant pathogen that causes leaf spot disease in a broad range of crop, and it heavily affect rubber trees in Malaysia (Hsueh, 2011; Nghia et al., 2008). The isolation of UM 591 from a patient’s contact lens indicates the pathogenic potential of this dematiaceous fungus in human. However, the underlying factors that contribute to the opportunistic cross-infection have not been fully studied. We employed genome sequencing and gene homology annotations in attempt to identify these factors in UM 591 using data obtained from publicly available bioinformatics databases. The assembly size of UM 591 genome is 41.8 Mbp, and a total of 13,531 (≥99 bp) genes have been predicted. UM 591 is enriched with genes that encode for glycoside hydrolases, carbohydrate esterases, auxiliary activity enzymes and cell wall degrading enzymes. Virulent genes comprising of CAZymes, peptidases, and hypervirulence-associated cutinases were found to be present in the fungal genome. Comparative analysis result shows that UM 591 possesses higher number of carbohydrate esterases family 10 (CE10) CAZymes compared to other species of fungi in this study, and these enzymes hydrolyses wide range of carbohydrate and non-carbohydrate substrates. Putative melanin, siderophore, ent-kaurene, and lycopene biosynthesis gene clusters are predicted, and these gene clusters denote that UM 591 are capable of protecting itself from the UV and chemical stresses, allowing it to adapt to different environment. Putative sterigmatocystin, HC-toxin, cercosporin, and gliotoxin biosynthesis gene cluster are predicted. This finding have highlighted the necrotrophic and invasive nature of UM 591. PMID:28149676

Origins Space Telescope: The Far Infrared Imager and Polarimeter FIP

NASA Astrophysics Data System (ADS)

Staguhn, Johannes G.; Chuss, David; Howard, Joseph; Meixner, Margaret; Vieira, Joaquin; Amatucci, Edward; Bradley, Damon; Carter, Ruth; Cooray, Asantha; Flores, Anel; Leisawitz, David; Moseley, Samuel Harvey; Wollack, Edward; Origins Space Telescope Study Team

2018-01-01

The Origins Space Telescope (OST)* is the mission concept for the Far-Infrared Surveyor, one of the four science and technology definition studies of NASA Headquarters for the 2020 Astronomy and Astrophysics Decadal survey. The current "concept 1", which envisions a cold (4K) 9m space telescope, includes 5 instruments, providing a wavelength coverage ranging from 6um and 667um. The achievable sensitivity of the observatory will provide three to four orders of magnitude of improvement in sensitivity over current observational capabilities, allowing to address a wide range of new and so far inaccessible scientific questions, ranging from bio-signatures on exo-planets to mapping primordial H_2 from the "dark ages" before the universe went through the phase of re-ionization.Here we present the Far Infrared Imager and Polarimeter (FIP) for OST. The cameral will cover four bands, 40um, 80um, 120um, and 240um. It will allow for differential polarimetry in those bands with the ability to observe two colors in polarimtery mode simultaneously, while all four bands can be observed simultaneously in total power mode. While the confusion limit will be reached in only 32ms at 240um, at 40um the source density on the sky is so low, that at the angular resolution of 1" of OST at this wavelength there will be no source confusion, even for the longest integration times. Science topics that can be addressed by FIP include but are not limited to galactic and extragalactic magnetic field studies, Deep Galaxy Surveys, and Outer Solar System objects..*Origins will enable flagship-quality general observing programs led by the astronomical community in the 2030s. We welcome you to contact the Science and Technology Definition Team (STDT) with your science needs and ideas by emailing us at ost_info@lists.ipac.caltech.edu

Measuring Broadband IR Irradiance in the Direct Solar Beam and Recent Developments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reda, Ibrahim; Andreas, Afshin; Dooraghi, Mike

2016-12-14

Solar and atmospheric science radiometers such as pyranometers, pyrheliometers, and photovoltaic cells are calibrated with traceability to a consensus reference which is maintained by Absolute Cavity Radiometers (ACRs). An ACR is an open cavity with no window, developed to measure the extended broadband spectrum of the terrestrial direct solar beam irradiance that extends beyond the ultraviolet and infrared bands; i.e. below 0.2 um and above 50 um, respectively. On the other hand, the pyranometers and pyrheliometers were developed to measure broadband shortwave irradiance from approximately 0.3 um to 3 um, while the present photovoltaic cells are limited to the spectralmore » range of approximately 0.3 um to 1 um. The broadband mismatch of ACR versus such radiometers causes discrepancy in radiometers' calibration methods that has not been discussed or addressed in the solar and atmospheric science literature. Pyrgeometers, which measure the atmospheric longwave irradiance, are also used for solar and atmospheric science applications and calibrated with traceability to a consensus reference, yet they are calibrated during nighttime only, because no consensus reference has been established for the daytime longwave irradiance. This poster describes a method to measure the broadband longwave irradiance in the terrestrial direct solar beam from 3 um to 50 um, as a first step that might be used to help develop calibration methods to address the mismatch between broadband ACR and shortwave radiometers, and the lack of a daytime reference for pyrgeometers. The described method is used to measure the irradiance from sunrise to sunset; the irradiance varied from approximately 1 Wm-2 to 16 Wm-2 with an estimated uncertainty of 1.5 Wm-2, for a solar zenith angle range from 80 degrees to 16 degrees, respectively. Recent development shows that there is greater than 1.1 percent bias in measuring shortwave solar irradiance.« less

UM-PRS: An implementation of the procedural reasoning system for multirobot applications

NASA Technical Reports Server (NTRS)

Lee, Jaeho; Huber, Marcus J.; Durfee, Edmund H.; Kenny, Patrick G.

1994-01-01

The Procedural Reasoning System (PRS) is used in applications where predetermined situations might arise. The UM-PRS provides a reasoning system that represents robotic applications even in unpredictable domains, such as the robotic reconnaissance task domain outlined here. UM-PRS incorporates a changing context, rather than relying solely on a prearranged plan. The UM-PRS here provides representation important in the reasoning and interface between a mission plan and the executable map of an outdoor vehicle that changes its behavior based on what it comes in contact with in its environment. PRS is thus used in the dynamic control of such a vehicle, providing the basis for coordinating the joint task of multiple robotic vehicles by the their individual observations and representation.

VizieR Online Data Catalog: FIR spectra of AGNs from Herschel (Fernandez-Ontiveros+, 2016)

NASA Astrophysics Data System (ADS)

Fernandez-Ontiveros, J. A.; Spinoglio, L.; Pereira-Santaella, M.; Malkan, M. A.; Andreani, P.; Dasyra, K. M.

2016-11-01

The combination of Herschel/PACS during its 3.5yr of operational life and Spitzer/IRS allows us to cover the fine-structure emission lines from the mid- to the far-IR (10-200um in the rest-frame) for all the galaxies in the sample. This database was completed with the Herschel/SPIRE published values of the [NII]205um, and [CI]371,609um line fluxes (mainly from Kamenetzky+ 2016ApJ...829...93K). Table 8 collects published mid-IR (10-35um) fine-structure line fluxes measured with Spitzer/IRS for our samples of AGN and starburst galaxies. These values were complemented with unpublished IRS observations from the Spitzer archive. (10 data files).

Monitoring the Near-infrared Volcanic Flux from Io's Jupiter-facing Hemisphere from Fan Mountain Observatory

NASA Astrophysics Data System (ADS)

Skrutskie, Michael F.; Nelson, Matthew J.; Schmidt, Carl

2016-10-01

Fan Mountain Observatory, near Charlottesville, Virginia, is a dark-sky site that supports a number of telescopes including a 31-inch reflecting telescope equipped with a 1024x1024 HgCdTe 1-2.5 um (YJHK) imager. Reflected sunlight ordinarily overwhelms Io's comparatively weak K-band (2.0-2.4 um) volcanic emission in unresolved observations, however when Io is eclipsed in Jupiter's shadow even a small infrared-equipped telescope can detect Io's volcanic emission. The Fan Mountain Infrared Camera observed Io in eclipse at regular intervals, typically weekly, during the few months before and after Jupiter's March 2016 opposition. When in eclipse Io's Jupiter-facing hemisphere is oriented toward Earth with sub-Earth longitudes at the time of observation ranging from 345 - 360 degrees (pre-opposition) to 0 - 15 degrees (post-opposition). A K-band filter (2.04-2.42 um) provided a bulk measurement of Io's volcanic flux weighted largely toward the 2.4 um end of this filter given the typical 500K color temperature of the volcanic emission. Most epochs also included observation in a narrowband filter centered at 2.12 um that, when combined with the broadband "long" wavelength measurement, provided a proxy for color temperature. The K-band flux of Io varied by more than 2 magnitudes during the 7 month observation interval. The [2.12 um - K-band] color of the emission strongly correlated with the K-band flux in the expected sense that the color temperature of the emission increased when Io's broadband volcanic flux was the greatest. One epoch of TripleSpec near-IR Io eclipse spectroscopy (0.90 - 2.45 um; R~3000) from the Apache Point Observatory 3.5-meter telescope provided ground truth for transforming the filter photometry into quantitative temperatures.

Genome analysis of Daldinia eschscholtzii strains UM 1400 and UM 1020, wood-decaying fungi isolated from human hosts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chan, Chai Ling; Yew, Su Mei; Ngeow, Yun Fong

Background: Daldinia eschscholtzii is a wood-inhabiting fungus that causes wood decay under certain conditions. It has a broad host range and produces a large repertoire of potentially bioactive compounds. However, there is no extensive genome analysis on this fungal species. Results: Two fungal isolates (UM 1400 and UM 1020) from human specimens were identified as Daldinia eschscholtzii by morphological features and ITS-based phylogenetic analysis. Both genomes were similar in size with 10,822 predicted genes in UM 1400 (35.8 Mb) and 11,120 predicted genes in UM 1020 (35.5 Mb). A total of 751 gene families were shared among both UM isolates,more » including gene families associated with fungus-host interactions. In the CAZyme comparative analysis, both genomes were found to contain arrays of CAZyme related to plant cell wall degradation. Genes encoding secreted peptidases were found in the genomes, which encode for the peptidases involved in the degradation of structural proteins in plant cell wall. In addition, arrays of secondary metabolite backbone genes were identified in both genomes, indicating of their potential to produce bioactive secondary metabolites. Both genomes also contained an abundance of gene encoding signaling components, with three proposed MAPK cascades involved in cell wall integrity, osmoregulation, and mating/filamentation. Besides genomic evidence for degrading capability, both isolates also harbored an array of genes encoding stress response proteins that are potentially significant for adaptation to living in the hostile environments. In conclusion: Our genomic studies provide further information for the biological understanding of the D. eschscholtzii and suggest that these wood-decaying fungi are also equipped for adaptation to adverse environments in the human host.« less

Activation pathways of synovial T lymphocytes. Expression and function of the UM4D4/CDw60 antigen.

PubMed Central

Fox, D A; Millard, J A; Kan, L; Zeldes, W S; Davis, W; Higgs, J; Emmrich, F; Kinne, R W

1990-01-01

Accumulating evidence implicates a central role for synovial T cells in the pathogenesis of rheumatoid arthritis, but the activation pathways that drive proliferation and effector function of these cells are not known. We have recently generated a novel monoclonal antibody against a rheumatoid synovial T cell line that recognizes an antigen termed UM4D4 (CDw60). This antigen is expressed on a minority of peripheral blood T cells, and represents the surface component of a distinct pathway of human T cell activation. The current studies were performed to examine the expression and function of UM4D4 on T cells obtained from synovial fluid and synovial membranes of patients with rheumatoid arthritis and other forms of inflammatory joint disease. The UM4D4 antigen is expressed at high surface density on about three-fourths of synovial fluid T cells and on a small subset of synovial fluid natural killer cells; in synovial tissue it is present on more than 90% of T cells in lymphoid aggregates, and on approximately 50% of T cells in stromal infiltrates In addition, UM4D4 is expressed in synovial tissue on a previously undescribed population of HLA-DR/DP-negative non-T cells with a dendritic morphology. Anti-UM4D4 was co-mitogenic for both RA and non-RA synovial fluid mononuclear cells, and induced IL-2 receptor expression. The UM4D4/CDw60 antigen may represent a functional activation pathway for synovial compartment T cells, which could play an important role in the pathogenesis of inflammatory arthritis. Images PMID:2212003

Mental health problems of undocumented migrants (UMs) in the Netherlands: a qualitative exploration of help-seeking behaviour and experiences with primary care

PubMed Central

Teunissen, Erik; Sherally, Jamilah; van den Muijsenbergh, Maria; Dowrick, Chris; van Weel-Baumgarten, Evelyn; van Weel, Chris

2014-01-01

Objective To explore health-seeking behaviour and experiences of undocumented migrants (UMs) in general practice in relation to mental health problems. Design Qualitative study using semistructured interviews and thematic analysis. Participants 15 UMs in the Netherlands, varying in age, gender, country of origin and education; inclusion until theoretical saturation was reached. Setting 4 cities in the Netherlands. Results UMs consider mental health problems to be directly related to their precarious living conditions. For support, they refer to friends and religion first, the general practitioner (GP) is their last resort. Barriers for seeking help include taboo on mental health problems, lack of knowledge of and trust in GPs competencies regarding mental health and general barriers in accessing healthcare as an UM (lack of knowledge of the right to access healthcare, fear of prosecution, financial constraints and practical difficulties). Once access has been gained, satisfaction with care is high. This is primarily due to the attitude of the GPs and the effectiveness of the treatment. Reasons for dissatisfaction with GP care are an experienced lack of time, lack of personal attention and absence of physical examination. Expectations of the GP vary, medication for mental health problems is not necessarily seen as a good practice. Conclusions UMs often see their precarious living conditions as an important determinant of their mental health; they do not easily seek help for mental health problems and various barriers hamper access to healthcare for them. Rather than for medication, UMs are looking for encouragement and support from their GP. We recommend that barriers experienced in seeking professional care are tackled at an institutional level as well as at the level of GP. PMID:25416057

Comparison of gene delivery techniques for therapeutic angiogenesis ultrasound-mediated destruction of carrier microbubbles versus direct intramuscular injection.

PubMed

Kobulnik, Jeremy; Kuliszewski, Michael A; Stewart, Duncan J; Lindner, Jonathan R; Leong-Poi, Howard

2009-10-27

This study was designed to compare the efficacy of angiogenic gene delivery by ultrasound-mediated (UM) destruction of intravenous carrier microbubbles to direct intramuscular (IM) injections. Current trials of gene therapy for angiogenesis remain limited by suboptimal, invasive delivery techniques. Hind-limb ischemia was produced by iliac artery ligation in 99 rats. In 32 rats, UM delivery of green fluorescent protein (GFP)/vascular endothelial growth factor-165 (VEGF(165)) plasmid deoxyribonucleic acid was performed. Thirty-five animals received IM injections of VEGF(165)/GFP plasmid. Remaining rats received no treatment. Before delivery (day 14 after ligation) and at days 17, 21, and 28 and week 8 after ligation, microvascular blood volume and microvascular blood flow to the proximal hind limbs were assessed by contrast-enhanced ultrasound (n = 8 per group). Total transfection was assessed by reverse transcriptase-polymerase chain reaction, and localization of transfection was determined by immunohistochemistry. By day 28, both IM and UM delivery of VEGF(165) produced significant increases in microvascular blood volume and microvascular blood flow. Whereas increases in microvascular blood volume were similar between treatment groups, microvascular blood flow was greater (p < 0.005) in UM-treated animals as compared with IM-treated animals, persisting to week 8. The VEGF(165)/GFP messenger ribonucleic acid expression was greater (p < 0.05) for IM-treated animals. A strong GFP signal was detected for both groups and was localized to focal perivascular regions and myocytes around injection sites for IM and to the vascular endothelium of arterioles/capillaries in a wider distribution for UM delivery. Despite lower transfection levels, UM delivery of VEGF(165) is as effective as IM injections. The UM delivery results in directed vascular transfection over a wider distribution, which may account for the more efficient angiogenesis.

Mental health problems of undocumented migrants in the Netherlands: A qualitative exploration of recognition, recording, and treatment by general practitioners.

PubMed

Teunissen, Erik; Van Bavel, Eric; Van Den Driessen Mareeuw, Francine; Macfarlane, Anne; Van Weel-Baumgarten, Evelyn; Van Den Muijsenbergh, Maria; Van Weel, Chris

2015-06-01

To explore the views and experiences of general practitioners (GPs) in relation to recognition, recording, and treatment of mental health problems of undocumented migrants (UMs), and to gain insight in the reasons for under-registration of mental health problems in the electronic medical records. Qualitative study design with semi-structured interviews using a topic guide. Sixteen GPs in the Netherlands with clinical expertise in the care of UMs. GPs recognized many mental health problems in UMs. Barriers that prevented them from recording these problems and from delivering appropriate care were their low consultation rates, physical presentation of mental health problems, high number of other problems, the UM's lack of trust towards health care professionals, and cultural differences in health beliefs and language barriers. Referrals to mental health care organizations were often seen as problematic by GPs. To overcome these barriers, GPs provided personalized care as far as possible, referred to other primary care professionals such as social workers or mental health care nurses in their practice, and were a little less restrictive in prescribing psychotropics than guidelines recommended. GPs experienced a variety of barriers in engaging with UMs when identifying or suspecting mental health problems. This explains why there is a gap between the high recognition of mental health problems and the low recording of these problems in general practice files. It is recommended that GPs address mental health problems more actively, strive for continuity of care in order to gain trust of the UMs, and look for opportunities to provide mental care that is accessible and acceptable for UMs.

Protective Effects of Ultramicronized Palmitoylethanolamide (PEA-um) in Myocardial Ischaemia and Reperfusion Injury in VIVO.

PubMed

Di Paola, Rosanna; Cordaro, Marika; Crupi, Rosalia; Siracusa, Rosalba; Campolo, Michela; Bruschetta, Giuseppe; Fusco, Roberta; Pugliatti, Pietro; Esposito, Emanuela; Cuzzocrea, Salvatore

2016-08-01

Myocardial infarction is the leading cause of death, occurs after prolonged ischemia of the coronary arteries. Restore blood flow is the first intervention help against heart attack. However, reperfusion of the arteries leads to ischemia/reperfusion injury (I/R). The fatty acid amide palmitoylethanolamide (PEA) is an endogenous compound widely present in living organisms, with analgesic and anti-inflammatory properties. The present study evaluated the effect of ultramicronized palmitoylethanolamide (PEA-um) treatment on the inflammatory process associated with myocardial I/R. Myocardial ischemia reperfusion injury was induced by occlusion of the left anterior descending coronary artery for 30 min followed by 2 h of reperfusion. PEA-um, was administered (10 mg/kg) 15 min after ischemia and 1 h after reperfusion. In this study, we demonstrated that PEA-um treatment reduces myocardial tissue injury, neutrophil infiltration, adhesion molecules (ICAM-1, P-selectin) expression, proinflammatory cytokines (TNF-α, IL-1β) production, nitrotyrosine and PAR formation, nuclear factor kB expression, and apoptosis (Fas-L, Bcl-2) activation. In addition to study whether the protective effect of PEA-um on myocardial ischemia reperfusion injury is also related to the activation of PPAR-α, in a separate set of experiments it has been performed myocardial I/R in PPARα mice. Genetic ablation of peroxisome proliferator activated receptor (PPAR)-α in PPAR-αKO mice exacerbated Myocardial ischemia reperfusion injury when compared with PPAR-αWT mice. PEA-um induced cardioprotection in PPAR-α wild-type mice, but the same effect cannot be observed in PPAR-αKO mice. Our results have clearly shown a modulation of the inflammatory process, associated with myocardial ischemia reperfusion injury, following administration of PEA-um.

Contralateral prophylactic mastectomy rate stable at major Canadian breast cancer center.

PubMed

Roberts, Amanda; Sandhu, Lakhbir; Cil, Tulin D; Hofer, Stefan O P; Zhong, Toni

2016-06-10

To examine trends of contralateral prophylactic mastectomy (CPM) rates at a Canadian academic breast cancer center. A single-institution retrospective cohort study was completed. Women of any age who underwent at least a unilateral mastectomy (UM) for primary unilateral breast carcinoma between January 1, 2004 and December 31, 2010 were included. Patients who underwent CPM on the same day as UM were isolated to create two distinct cohorts. Patient and procedure characteristics were compared across groups using R software (version 3.1.0). The percentage of CPMs per year was determined. The Cochrane-Armitage test was used to assess the trend of CPMs over time. A P value of < 0.05 was considered significant. A total of 811 women met the inclusions/exclusion criteria; 759 (93.6%) underwent UM alone and 52 (6.4%) underwent UM with immediate CPM. The absolute number of procedures (UM and UM + CPM) increased over time, from 83 in 2004 to 147 in 2010 reflecting an increase in mastectomy volume. Annual CPM rates did not increase over time (P = 0.7) and varied between 2.6% to 10.7%. Family history of breast cancer [OR 3.6 (1.8-7.3)] and immediate reconstruction [10.0 (5.2-19.3)] were both significantly associated with CPM. Women who underwent CPM were younger (median age CPM 49 years vs UM 52 years, P < 0.0001) but age less than 50 years was not statistically associated with increased rates of CPM. CPM rates from 2004 to 2010 at a high-volume Canadian breast cancer center did not increase over time, in contrast to trends observed in the United States.

First Asteroid Spectrometric Observations with BTA: 3045 Alois

NASA Astrophysics Data System (ADS)

Busarev, V. V.; Burenkov, A. N.; Pramskij, A. G.

2001-11-01

BTA, Russian 6-m telescope, was mainly used for faint stars and extragalactic objects observations. We have firstly performed with the telescope spectrometric observations of a main belt asteroid, 3045 Alois, and are planning to use it for Centaurs and Kuiper Belt objects spectrometry. We have obtained some results of the observations. Spectra of Alois were recorded on two nights of March 2001 (29/30 and 30/31) with a long slit spectrograph (UAGS + CCD) in the .38-.80 um spectral range. HD105633 (G5) [1] considered as a solar analog was also observed, and the data were used for calculation the asteroid reflectance spectra. It was found that reflectance spectra of Alois obtained on different nights have various continuum slopes and absorption features. The reflectance spectrum on 29/30 March had a flat continuum in the range .44-.65 um and absorption bands at .5 um (ab. 7 % with respect to the continuum) similar to that found on the E-type asteroid 2035 Stearns [2], and at .80 um (ab. 25 %). Another one on 30/31 March had a red continuum in the range .40-.67 um and absorption bands at .43 um (ab. 6 %) resembling absorption features found on some C-, M- and S-type asteroids [3, 4], and at .80 um (ab. 17 %). From the data and taking into account the mean heliocentric distance of 3045 Alois (3.13 AU) we suppose that the asteroid having irregular spectral characteristics may be of M- or E-type and possibly hydrated. Unfortunately, its albedo and rotational period remain still unknown. [1] Mermilliod J.-C. (1994) Bull. Inf. CDS 45, 3. [2] Fornasier S. and Lazzarine M. (2001) Icarus 152, 127-133. [3] Vilas F. et al. (1993) Icarus 102, 225-231. [4] Busarev V. V. (2001) LPSC XXXII, abs. 1927.

Genome analysis of Daldinia eschscholtzii strains UM 1400 and UM 1020, wood-decaying fungi isolated from human hosts

DOE PAGES

Chan, Chai Ling; Yew, Su Mei; Ngeow, Yun Fong; ...

2015-11-18

Background: Daldinia eschscholtzii is a wood-inhabiting fungus that causes wood decay under certain conditions. It has a broad host range and produces a large repertoire of potentially bioactive compounds. However, there is no extensive genome analysis on this fungal species. Results: Two fungal isolates (UM 1400 and UM 1020) from human specimens were identified as Daldinia eschscholtzii by morphological features and ITS-based phylogenetic analysis. Both genomes were similar in size with 10,822 predicted genes in UM 1400 (35.8 Mb) and 11,120 predicted genes in UM 1020 (35.5 Mb). A total of 751 gene families were shared among both UM isolates,more » including gene families associated with fungus-host interactions. In the CAZyme comparative analysis, both genomes were found to contain arrays of CAZyme related to plant cell wall degradation. Genes encoding secreted peptidases were found in the genomes, which encode for the peptidases involved in the degradation of structural proteins in plant cell wall. In addition, arrays of secondary metabolite backbone genes were identified in both genomes, indicating of their potential to produce bioactive secondary metabolites. Both genomes also contained an abundance of gene encoding signaling components, with three proposed MAPK cascades involved in cell wall integrity, osmoregulation, and mating/filamentation. Besides genomic evidence for degrading capability, both isolates also harbored an array of genes encoding stress response proteins that are potentially significant for adaptation to living in the hostile environments. In conclusion: Our genomic studies provide further information for the biological understanding of the D. eschscholtzii and suggest that these wood-decaying fungi are also equipped for adaptation to adverse environments in the human host.« less

Aircraft Natural/Artificial Icing

DTIC Science & Technology

2009-02-12

LWC are 0.1 to 0.8 g/m3 for stratiform clouds and 0.2 to 2.5 g/m3 for cumuliform clouds. The drop size distribution in the cloud is usually...cloud hydrometeor size distributions from 0.5 to 50 um, particle shape (discrimination between water and ice), particle optical properties (refractive...index), precipitation size distributions from 25 um to 1550 um, liquid water content from 0.01 to 3 gm-3 and aircraft velocity and atmospheric

Novel Preclinical Testing Strategies for Treatment of Metastatic Pheochromocytoma

DTIC Science & Technology

2013-09-01

proliferation using this protocol as reported or with any modifications tested Medium Y27632 (uM) Hydrocortisone (ug/mL) Insulin (ug/mL) rhEGF...0 + + 0 + + 0 + 0 Medium Y27632 (uM) Hydrocortisone (ug/mL) Insulin (ug/mL) rhEGF (ng/mL) Adenine (ug/mL) Result...reported (1) except for cholera toxin, which was toxic to this tumor under these conditions 17 Medium Y27632 (uM) Hydrocortisone (ug/mL

BRD4-targeted therapy induces Myc-independent cytotoxicity in Gnaq/11-mutatant uveal melanoma cells.

PubMed

Ambrosini, Grazia; Sawle, Ashley D; Musi, Elgilda; Schwartz, Gary K

2015-10-20

Uveal melanoma (UM) is an aggressive intraocular malignancy with limited therapeutic options. Both primary and metastatic UM are characterized by oncogenic mutations in the G-protein alpha subunit q and 11. Furthermore, nearly 40% of UM has amplification of the chromosomal arm 8q and monosomy of chromosome 3, with consequent anomalies of MYC copy number. Chromatin regulators have become attractive targets for cancer therapy. In particular, the bromodomain and extra-terminal (BET) inhibitor JQ1 has shown selective inhibition of c-Myc expression with antiproliferative activity in hematopoietic and solid tumors. Here we provide evidence that JQ1 had cytotoxic activity in UM cell lines carrying Gnaq/11 mutations, while in cells without the mutations had little effects. Using microarray analysis, we identified a large subset of genes modulated by JQ1 involved in the regulation of cell cycle, apoptosis and DNA repair. Further analysis of selected genes determined that the concomitant silencing of Bcl-xL and Rad51 represented the minimal requirement to mimic the apoptotic effects of JQ1 in the mutant cells, independently of c-Myc. In addition, administration of JQ1 to mouse xenograft models of Gnaq-mutant UM resulted in significant inhibition of tumor growth.Collectively, our results define BRD4 targeting as a novel therapeutic intervention against UM with Gnaq/Gna11 mutations.

Unsaponifiable matter from oil of green coffee beans: cosmetic properties and safety evaluation.

PubMed

Wagemaker, Tais A L; Campos, Patrícia M B G Maia; Fernandes, Ana Sofia; Rijo, Patrícia; Nicolai, Marisa; Roberto, Amílcar; Rosado, Catarina; Reis, Catarina; Rodrigues, Luis M; Carvalho, Cássia Regina Limonta; Maia, Nilson Borlina; Guerreiro Filho, Oliveiro

2016-10-01

Unsaponifiable matter (UM), a fraction of green coffee oil (GCO) contains functional compounds responsible for desirable cosmetic properties such as UV-B absorption. To evaluate oil content and sun protection factor (SPF) variability of the two most important species of coffee and, the toxic and cytotoxic effects, as well as cosmetic properties, including antioxidant and antimicrobial activities of UM obtained from green Coffea arabica seed oil. The safety and potential cosmetic properties of UM extracted from green coffee oil (GCO) were evaluated by the brine shrimp viability and the MTT cytotoxicity assays. The SPF and antioxidant activity were evaluated using in vitro methods. Relevant cytotoxicity was found against keratinocytes for concentrations ≥25 µg/mL and in the brine shrimp assay (LC50 24 µg/mL). Antimicrobial and antioxidant activities (IC50 1448 µg/mL) were low in UM but SPF was 10 times higher than in GCO. UM is a novel potential UV-B absorbent but its use as a cosmetic ingredient should be better considered due to the considerable cytotoxicity shown in the experimental conditions described.

Medusa consumption and prey selection of silver pomfret Pampus argenteus juveniles

NASA Astrophysics Data System (ADS)

Liu, Chunsheng; Zhuang, Zhimeng; Chen, Siqing; Shi, Zhaohong; Yan, Jingping; Liu, Changlin

2014-01-01

The current study explored Aurelia aurita and Rhopilema esculent um consumption by silver pomfret juveniles, as well as their prey selection between the two jellyfish species. Silver pomfret juveniles weighing 1±0.1 g actively preyed on both the species. Their daily A. aurita consumption was 11.6 times their own body weights regardless of the size of A. aurita medusae. Their daily R. esculent um consumption was 13, 9.1, 5, and 4.1 times their own body weights when the R. esculentum medusae were 10, 20, 30, and 40 mm in bell diameter, respectively. The survival rates of the R. esculent um were higher than those of the A. aurita. When the R. esculent um medusae were more than 30 mm in bell diameter, their survival rate exceeded 92%. Silver pomfrets serve as a type of potential predators on A. aurita in coastal waters, and they have little influence on R. esculent um with a size exceeding 30 mm. Besides, A. aurita may be able to be used as fish prey in silver pomfret artificial breeding.

Posttest analysis of LOFT LOCE L2-3 using the ESA RELAP4 blowdown model. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perryman, J.L.; Samuels, T.K.; Cooper, C.H.

A posttest analysis of the blowdown portion of Loss-of-Coolant Experiment (LOCE) L2-3, which was conducted in the Loss-of-Fluid Test (LOFT) facility, was performed using the experiment safety analysis (ESA) RELAP4/MOD5 computer model. Measured experimental parameters were compared with the calculations in order to assess the conservatisms in the ESA RELAP4/MOD5 model.

Fusion Helmet: Electronic Analysis

DTIC Science & Technology

2014-04-01

Table 1: LYR203-101B Board Feature P1 (SEC MODULE) DM648 GPIO PORn Video Ports (2) Bootmode SPI/UART I2C CLKIN MDIO DDR2 128MB/16bit SPI Flash 16...McASP EMAC-SGMII /2 MDIO I2C GPIO DDR2 128MB/16bit JTAG Memory CLKGEN I2C PGoodPGood PORn Pwr LED Power DSP SPI/UART DSP SPI/UARTSPI/UART Video Display

PWR PRELIMINARY DESIGN FOR PL-3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Humphries, G. E.

1962-02-28

The pressurized water reactor preliminary design, the preferred design developed under Phase I of the PL-3 contract, is presented. Plant design criteria, summary of plant selection, plant description, reactor and primary system description, thermal and hydraulic analysis, nuclear analysis, control and instrumentatlon description, shielding description, auxiliary systems, power plant equipment, waste dispusal, buildings and tunnels, services, operation and maintenance, logistics, erection, cost information, and a training program outline are given. (auth)

Solar Photovoltaic and Liquid Natural Gas Opportunities for Command Naval Region Hawaii

DTIC Science & Technology

2014-12-01

Utilities Commission xii PV Photovoltaic Pwr Power RE Renewable Energy Re-gas Regasification RFP Request For Proposal RMI Rocky... forecasted LS diesel price and the forecasted LNG delivered-to-the- power -plant cost. The forecast for LS diesel by FGE from year 2020–2030 is seen...annual/html/epa_08_01.html Electric Power Research Institute. (July, 2010). Addressing solar photovoltaic operations and maintenance challenges: A

Statistical evaluation of the metallurgical test data in the ORR-PSF-PVS irradiation experiment. [PWR; BWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stallmann, F.W.

1984-08-01

A statistical analysis of Charpy test results of the two-year Pressure Vessel Simulation metallurgical irradiation experiment was performed. Determination of transition temperature and upper shelf energy derived from computer fits compare well with eyeball fits. Uncertainties for all results can be obtained with computer fits. The results were compared with predictions in Regulatory Guide 1.99 and other irradiation damage models.

Two-phase Fluid Selection for High-temperature Automotive Platforms

DTIC Science & Technology

2012-09-01

cases, extra work by researchers can be done to uprate the device, either by parameter conformance, parameter re-characterization, or stress balancing...chemical reactivity , noble metal oxidization, intermetallic growth, CTE mismatch and other failure mechanisms are an issue with wide bandgap...21005-1852 1 US ARMY TARDEC ATTN AMSRD TAR E/ PWR C SPANGLER 6501 E 11 MILE RD, BLDG 212 WARREN MI 48397-5000 1 UNIV OF MARYLAND

CH-47C Vulnerability Reduction Modification Program - Fly-by-Wire Backup Demonstration

DTIC Science & Technology

1976-08-01

Actuator Position for Combined Axis Input ............................. 91 4 Systems Assessment Summary................... 95 C-1 Instrumentation Parameters ...SERVO CARD jEETO FROM MIXERS SUfEV __________ HYLIC AMPL AMPLVLE SHUT-O- DOWN DC PWR LOGIC REA MIONITOR SUMMER *O:EO SWITCH- BUFFER OVER 1 NETWORK...and ranels (Figures 12 and 13). The existing DELS preflight test set, which provides access to the system parameters , was installed along with the

Reactor Dosimetry Applications Using RAPTOR-M3G:. a New Parallel 3-D Radiation Transport Code

NASA Astrophysics Data System (ADS)

Longoni, Gianluca; Anderson, Stanwood L.

2009-08-01

The numerical solution of the Linearized Boltzmann Equation (LBE) via the Discrete Ordinates method (SN) requires extensive computational resources for large 3-D neutron and gamma transport applications due to the concurrent discretization of the angular, spatial, and energy domains. This paper will discuss the development RAPTOR-M3G (RApid Parallel Transport Of Radiation - Multiple 3D Geometries), a new 3-D parallel radiation transport code, and its application to the calculation of ex-vessel neutron dosimetry responses in the cavity of a commercial 2-loop Pressurized Water Reactor (PWR). RAPTOR-M3G is based domain decomposition algorithms, where the spatial and angular domains are allocated and processed on multi-processor computer architectures. As compared to traditional single-processor applications, this approach reduces the computational load as well as the memory requirement per processor, yielding an efficient solution methodology for large 3-D problems. Measured neutron dosimetry responses in the reactor cavity air gap will be compared to the RAPTOR-M3G predictions. This paper is organized as follows: Section 1 discusses the RAPTOR-M3G methodology; Section 2 describes the 2-loop PWR model and the numerical results obtained. Section 3 addresses the parallel performance of the code, and Section 4 concludes this paper with final remarks and future work.

Fretting wear behaviors of a dual-cooled nuclear fuel rod under a simulated rod vibration

NASA Astrophysics Data System (ADS)

Lee, Young-Ho; Kim, Hyung-Kyu; Kang, Heung-Seok; Yoon, Kyung-Ho; Kim, Jae-Yong; Lee, Kang-Hee

2012-06-01

Recently, a dual-cooled fuel (i.e., annular fuel) that is compatible with current operating PWR plants has been proposed in order to realize both a considerable amount of power uprating and an increase of safety margins. As the design concept should be compatible with current operating PWR plants, however, it shows a narrow gap between the fuel rods when compared with current solid nuclear fuel arrays and needs to modify the spacer grid shapes and their positions. In this study, fretting wear tests have been performed to evaluate the wear resistance of a dual-cooled fuel by using a proposed spring and dimple of spacer grids that have a cantilever type and hemispherical shape, respectively. As a result, the wear volume of the spring specimen gradually increases as the contact condition is changed from a certain gap, just contact to positive force. However, in the dimple specimen, just contact condition shows a large wear volume. In addition, a circular rod motion at upper region of contact surface is gradually increased and its diametric size depends on the wear depth increase. Based on the test results, the fretting wear resistance of the proposed spring and dimple is analyzed by comparing the wear measurement results and rod motion in detail.

Hybrid parallel code acceleration methods in full-core reactor physics calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Courau, T.; Plagne, L.; Ponicot, A.

2012-07-01

When dealing with nuclear reactor calculation schemes, the need for three dimensional (3D) transport-based reference solutions is essential for both validation and optimization purposes. Considering a benchmark problem, this work investigates the potential of discrete ordinates (Sn) transport methods applied to 3D pressurized water reactor (PWR) full-core calculations. First, the benchmark problem is described. It involves a pin-by-pin description of a 3D PWR first core, and uses a 8-group cross-section library prepared with the DRAGON cell code. Then, a convergence analysis is performed using the PENTRAN parallel Sn Cartesian code. It discusses the spatial refinement and the associated angular quadraturemore » required to properly describe the problem physics. It also shows that initializing the Sn solution with the EDF SPN solver COCAGNE reduces the number of iterations required to converge by nearly a factor of 6. Using a best estimate model, PENTRAN results are then compared to multigroup Monte Carlo results obtained with the MCNP5 code. Good consistency is observed between the two methods (Sn and Monte Carlo), with discrepancies that are less than 25 pcm for the k{sub eff}, and less than 2.1% and 1.6% for the flux at the pin-cell level and for the pin-power distribution, respectively. (authors)« less

Current training initiatives at Nuclear Electric plc

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fowler, C.D.

1993-01-01

Nuclear Electric, one of the three generating companies to emerge from the demise of the U.K.'s Central Electricity Generating Board (CEGB), owns and operates the commercial nuclear power stations in England and Wales. The U.K. government proscribed further construction beyond Sizewell B, the United Kingdom's first pressurized water reactor (PWR) station, pending the outcome of a review of the future of nuclear power to be held in 1994. The major challenges facing Nuclear Electric at its formation in 1990 were therefore to demonstrate that nuclear power is safe, economical, and environmentally acceptable and to complete the PWR station under constructionmore » on time and within budget. A significant number of activities were started that were designed to increase output, reduce costs, and ensure that the previous excellent safety standards were maintained. A major activity was to reduce the numbers of staff employed, with a recognition from the outset that this reduction could only be achieved with a significant human resource development program. Future company staff would have to be competent in more areas and more productive. This paper summarizes some of the initiatives currently being pursued throughout the company and the progress toward ensuring that staff with the required competences are available to commission and operate the Sizewell B program in 1994.« less

System Engineering for J-2X Development: The Simpler, the Better

NASA Technical Reports Server (NTRS)

Kelly, William M.; Greasley, Paul; Greene, William D.; Ackerman, Peter

2008-01-01

The Ares I and Ares V Vehicles will utilize the J-2X rocket engine developed for NASA by the Pratt and Whitney Rocketdyne Company (PWR) as the upper stage engine (USE). The J-2X is an improved higher power version of the original J-2 engine used for Apollo. System Engineering (SE) facilitates direct and open discussions of issues and problems. This simple idea is often overlooked in large, complex engineering development programs. Definition and distribution of requirements from the engine level to the component level is controlled by Allocation Reports which breaks down numerical design objectives (weight, reliability, etc.) into quanta goals for each component area. Linked databases of design and verification requirements help eliminate redundancy and potential mistakes inherent in separated systems. Another tool, the Architecture Design Description (ADD), is used to control J-2X system architecture and effectively communicate configuration changes to those involved in the design process. But the proof of an effective process is in successful program accomplishment. SE is the methodology being used to meet the challenge of completing J-2X engine certification 2 years ahead of any engine program ever developed at PWR. This paper describes the simple, better SE tools and techniques used to achieve this success.

Investigation into the effect of water chemistry on corrosion product formation in areas of accelerated flow

NASA Astrophysics Data System (ADS)

McGrady, John; Scenini, Fabio; Duff, Jonathan; Stevens, Nicholas; Cassineri, Stefano; Curioni, Michele; Banks, Andrew

2017-09-01

The deposition of CRUD (Chalk River Unidentified Deposit) in the primary circuit of a Pressurised Water Reactor (PWR) is known to preferentially occur in regions of the circuit where flow acceleration of coolant occurs. A micro-fluidic flow cell was used to recreate accelerated flow under simulated PWR conditions, by flowing water through a disc with a central micro-orifice. CRUD deposition was reproduced on the disc, and CRUD Build-Up Rates (BUR) in various regions of the disc were analysed. The effect of the local environment on BUR was investigated. In particular, the effect of flow velocity, specimen material and Fe concentration were considered. The morphology and composition of the deposits were analysed with respect to experimental conditions. The BUR of CRUD was found to be sensitive to flow velocity and Fe concentration, suggesting that mass transfer is an important factor. The morphology of the deposit was affected by the specimen material indicating a dependence on surface/particle electrostatics meaning surface chemistry plays an important role in deposition. The preferential deposition of CRUD in accelerated flow regions due to electrokinetic effects was observed and it was shown that higher Fe concentrations in solution increased BURs within the orifice whereas increased flow velocity reduced BURs.

Penetrative Internal Oxidation from Alloy 690 Surfaces and Stress Corrosion Crack Walls during Exposure to PWR Primary Water

NASA Astrophysics Data System (ADS)

Olszta, Matthew J.; Schreiber, Daniel K.; Thomas, Larry E.; Bruemmer, Stephen M.

Analytical electron microscopy and three-dimensional atom probe tomography (ATP) examinations of surface and near-surface oxidation have been performed on Ni-30%Cr alloy 690 materials after exposure to high-temperature, simulated PWR primary water. The oxidation nanostructures have been characterized at crack walls after stress-corrosion crack growth tests and at polished surfaces of unstressed specimens for the same alloys. Localized oxidation was discovered for both crack walls and surfaces as continuous filaments (typically <10 nm in diameter) extending from the water interface into the alloy 690 matrix reaching depths of 500 nm. These filaments consisted of discrete, plate-shaped Cr2O3 particles surrounded by a distribution of nanocrystalline, rock-salt (Ni-Cr-Fe) oxide. The oxide-containing filament depth was found to increase with exposure time and, at longer times, the filaments became very dense at the surface leaving only isolated islands of metal. Individual dislocations were oxidized in non-deformed materials, while the oxidation path appeared to be along more complex dislocation substructures in heavily deformed materials. This paper will highlight the use of high resolution scanning and transmission electron microscopy in combination with APT to better elucidate the microstructure and microchemistry of the filamentary oxidation.

TRIGA MARK-II source term

DOE Office of Scientific and Technical Information (OSTI.GOV)

Usang, M. D., E-mail: mark-dennis@nuclearmalaysia.gov.my; Hamzah, N. S., E-mail: mark-dennis@nuclearmalaysia.gov.my; Abi, M. J. B., E-mail: mark-dennis@nuclearmalaysia.gov.my

ORIGEN 2.2 are employed to obtain data regarding γ source term and the radio-activity of irradiated TRIGA fuel. The fuel composition are specified in grams for use as input data. Three types of fuel are irradiated in the reactor, each differs from the other in terms of the amount of Uranium compared to the total weight. Each fuel are irradiated for 365 days with 50 days time step. We obtain results on the total radioactivity of the fuel, the composition of activated materials, composition of fission products and the photon spectrum of the burned fuel. We investigate the differences ofmore » results using BWR and PWR library for ORIGEN. Finally, we compare the composition of major nuclides after 1 year irradiation of both ORIGEN library with results from WIMS. We found only minor disagreements between the yields of PWR and BWR libraries. In comparison with WIMS, the errors are a little bit more pronounced. To overcome this errors, the irradiation power used in ORIGEN could be increased a little, so that the differences in the yield of ORIGEN and WIMS could be reduced. A more permanent solution is to use a different code altogether to simulate burnup such as DRAGON and ORIGEN-S. The result of this study are essential for the design of radiation shielding from the fuel.« less

Sub-Scale Testing and Development of the J-2X Fuel Turbopump Inducer

NASA Technical Reports Server (NTRS)

Sargent, Scott R.; Becht, David G.

2011-01-01

In the early stages of the J-2X upper stage engine program, various inducer configurations proposed for use in the fuel turbopump (FTP) were tested in water. The primary objectives of this test effort were twofold. First, to obtain a more comprehensive data set than that which existed in the Pratt & Whitney Rocketdyne (PWR) historical archives from the original J-2S program, and second, to supplement that data set with information regarding the cavitation induced vibrations for both the historical J-2S configuration as well as those tested for the J-2X program. The J-2X FTP inducer, which actually consists of an inducer stage mechanically attached to a kicker stage, underwent 4 primary iterations utilizing sub-scaled test articles manufactured and tested in PWR's Engineering Development Laboratory (EDL). The kicker remained unchanged throughout the test series. The four inducer configurations tested retained many of the basic design features of the J-2S inducer, but also included variations on leading edge blade thickness and blade angle distribution, primarily aimed at improving suction performance at higher flow coefficients. From these data sets, the effects of the tested design variables on hydrodynamic performance and cavitation instabilities were discerned. A limited comparison of impact to the inducer efficiency was determined as well.

Development Status of the CECE Cryogenic Deep Throttling Demonstrator Engine

NASA Technical Reports Server (NTRS)

2008-01-01

As one of the first technology development programs awarded by NASA under the U.S. Space Exploration Policy (USSEP), the Pratt & Whitney Rocketdyne (PWR) Deep Throttling, Common Extensible Cryogenic Engine (CECE) program was selected by NASA in November 2004 to begin technology development and demonstration toward a deep throttling, cryogenic engine supporting ongoing trade studies for NASA's Lunar Lander descent stage. The CECE program leverages the maturity and previous investment of a flight-proven hydrogen/oxygen expander cycle engine, the PWR RLI0, to develop and demonstrate an unprecedented combination of reliability, safety, durability, throttlability, and restart capabilities in a high-energy, cryogenic engine. The testbed selected for the deep throttling demonstration phases of this program was a minimally modified RL10 engine, allowing for maximum current production engine commonality and extensibility with minimum program cost. Two series of demonstrator engine tests, the first in April-May 2006 and the second in March-April 2007, have demonstrated in excess of 10:1 throttling of the hydrogen/oxygen expander cycle engine. Both test series have explored a combustion instability ("chug") environment at low throttled power levels. These tests have provided an early demonstration of an enabling cryogenic propulsion concept with invaluable system-level technology data acquisition toward design and development risk mitigation for future CECE Demonstrator engine tests.

Nuclear fuel performance: Trends, remedies and challenges

NASA Astrophysics Data System (ADS)

Rusch, C. A.

2008-12-01

It is unacceptable to have nuclear power plants unavailable or power restricted due to fuel reliability issues. 'Fuel reliability' has a much broader definition than just maintaining mechanical integrity and being leaker free - fuel must fully meet the specifications, impose no adverse impacts on plant operation and safety, and maintain quantifiable margins within design and operational envelopes. The fuel performance trends over the last decade are discussed and the significant contributors to reduced reliability experienced with commercial PWR and BWR designs are identified and discussed including grid-to-rod fretting and debris fretting in PWR designs and accelerated corrosion, debris fretting and pellet-cladding interaction in BWR designs. In many of these cases, the impacts have included not only fuel failures but also plant operating restrictions, forced shutdowns, and/or enhanced licensing authority oversight. Design and operational remedies are noted. The more demanding operating regimes and the constant quest to improve fuel performance require enhancements to current designs and/or new design features. Fuel users must continue to and enhance interaction with fuel suppliers in such areas as oversight of supplier design functions, lead test assembly irradiation programs and quality assurance oversight and surveillance. With the implementation of new designs and/or features, such fuel user initiatives can help to minimize the potential for performance problems.

Probabilistic pipe fracture evaluations for leak-rate-detection applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rahman, S.; Ghadiali, N.; Paul, D.

1995-04-01

Regulatory Guide 1.45, {open_quotes}Reactor Coolant Pressure Boundary Leakage Detection Systems,{close_quotes} was published by the U.S. Nuclear Regulatory Commission (NRC) in May 1973, and provides guidance on leak detection methods and system requirements for Light Water Reactors. Additionally, leak detection limits are specified in plant Technical Specifications and are different for Boiling Water Reactors (BWRs) and Pressurized Water Reactors (PWRs). These leak detection limits are also used in leak-before-break evaluations performed in accordance with Draft Standard Review Plan, Section 3.6.3, {open_quotes}Leak Before Break Evaluation Procedures{close_quotes} where a margin of 10 on the leak detection limit is used in determining the crackmore » size considered in subsequent fracture analyses. This study was requested by the NRC to: (1) evaluate the conditional failure probability for BWR and PWR piping for pipes that were leaking at the allowable leak detection limit, and (2) evaluate the margin of 10 to determine if it was unnecessarily large. A probabilistic approach was undertaken to conduct fracture evaluations of circumferentially cracked pipes for leak-rate-detection applications. Sixteen nuclear piping systems in BWR and PWR plants were analyzed to evaluate conditional failure probability and effects of crack-morphology variability on the current margins used in leak rate detection for leak-before-break.« less

Fatigue limit and Hysteresis Behavior of Type 304L Stainless Steel in Air and PWR Water, at 150°C and 300°C

NASA Astrophysics Data System (ADS)

Solomon, H. D.; Amzallag, C.; Vallee, A. J.; DeLair, R. E.

This is a study of the 107 cycle fatigue limit of Type 304L Stainless Steel, as measured in fully reversed (R=-1) load-controlled tests, at 150°C and 300°C, in air and PWR water. The staircase method was used to determine the fatigue limit. The tests run here utilized a cycle frequency of 1.818Hz and are compared to other tests from the literature that were run at 30Hz. The fatigue limit measured in the tests run at the high frequency was higher than that measured here. This is explained by measurements of the strain developed during cycling, using the different cycle frequencies. The tests run at the higher frequencies yielded lower strains for a given stress and, as expected, this resulted in higher fatigue limits. Using 107 cycles to define a run-out also led to a lower fatigue limit. These results are important as most previous fatigue limit measurements utilized 106 cycles or less to define a run-out, and when lives as long as 107 cycles are used the tests are generally run at high cycle frequencies, thus leading to higher fatigue limits than those measured here.

Influence of Localized Plasticity on IASCC Sensitivity of Austenitic Stainless Steels under PWR Primary Water

NASA Astrophysics Data System (ADS)

Cissé, Sarata; Tanguy, Benoit; Laffont, Lydia; Lafont, Marie-Christine; Guerre, Catherine; Andrieu, Eric

The sensibility of precipitation-strengthened A286 austenitic stainless steel to Stress Corrosion Cracking (SCC) is studied by means of Slow Strain Rate Tests (SSRT). First, alloy cold working by Low Cycle Fatigue (LCF) is investigated. Fatigue tests under plastic strain control are performed at different strain levels (Δ ɛp/2=0.2%, 0.5% and 0.8%) in order to establish correlation between stress softening and deformation microstructure resulting from LCF tests. Deformed microstructures have been identified through TEM investigations. Three states of cyclic behaviour for precipitation-strengthened A286 have been identified: hardening, cyclic softening and finally saturation of softening. It is shown that the A286 alloy cyclic softening is due to microstructural features such as defects — free deformation bands resulting from dislocations motion along family plans <111>, that swept defects or γ' precipitates and lead to deformation localization. In order to quantify effects of plastic localized deformation on intergranular stress corrosion cracking (IGSCC) of the A286 alloy in PWR primary water, slow strain rate tests are conducted. For each cycling conditions, two specimens at a similar stress level are tested: the first containing free precipitate deformation bands, the other not significant of a localized deformation state. SSRT tests are still in progress.

Influence of localized deformation on A-286 austenitic stainless steel stress corrosion cracking in PWR primary water

NASA Astrophysics Data System (ADS)

Fournier, L.; Savoie, M.; Delafosse, D.

2007-06-01

The low cycle fatigue (LCF) behaviour of precipitation-strengthened A-286 austenitic stainless steel was first investigated at room temperature under 0.2% plastic strain control. LCF led to hardening for the first 20 cycles and then to significant softening. LCF-induced dislocation microstructure was characterized using both bright and dark-field imaging techniques in transmission electron microscopy. Cycling softening was correlated with the formation of precipitate-free localized deformation bands. The effect of these precipitate-free localized deformation bands on A-286 stress corrosion cracking (SCC) behaviour in PWR primary water was then examined by means of constant extension rate tensile (CERT) tests at 320 °C and 360 °C. Comparative CERT tests were performed on companion specimens with similar yield stress but pre-fatigued to a few cycles (4-8) or between 125 and 200 cycles. Specimens pre-fatigued to a few cycles with no precipitate-free localized deformation bands exhibited little susceptibility to intergranular SCC (IGSCC). In contrast, the presence of precipitate-free localized deformation bands formed by pre-fatigue to between 125 and 200 cycles strongly promoted IGSCC. The interest of the approach used in this study is to provide insight into the role of localized deformation in irradiation assisted stress corrosion cracking.

Characterization of ion irradiation effects on the microstructure, hardness, deformation and crack initiation behavior of austenitic stainless steel:Heavy ions vs protons

NASA Astrophysics Data System (ADS)

Gupta, J.; Hure, J.; Tanguy, B.; Laffont, L.; Lafont, M.-C.; Andrieu, E.

2018-04-01

Irradiation Assisted Stress Corrosion Cracking (IASCC) is a complex phenomenon of degradation which can have a significant influence on maintenance time and cost of core internals of a Pressurized Water Reactor (PWR). Hence, it is an issue of concern, especially in the context of lifetime extension of PWRs. Proton irradiation is generally used as a representative alternative of neutron irradiation to improve the current understanding of the mechanisms involved in IASCC. This study assesses the possibility of using heavy ions irradiation to evaluate IASCC mechanisms by comparing the irradiation induced modifications (in microstructure and mechanical properties) and cracking susceptibility of SA 304 L after both type of irradiations: Fe irradiation at 450 °C and proton irradiation at 350 °C. Irradiation-induced defects are characterized and quantified along with nano-hardness measurements, showing a correlation between irradiation hardening and density of Frank loops that is well captured by Orowan's formula. Both irradiations (iron and proton) increase the susceptibility of SA 304 L to intergranular cracking on subjection to Constant Extension Rate Tensile tests (CERT) in simulated nominal PWR primary water environment at 340 °C. For these conditions, cracking susceptibility is found to be quantitatively similar for both irradiations, despite significant differences in hardening and degree of localization.

ADVANCEMENTS IN TIME-SPECTRA ANALYSIS METHODS FOR LEAD SLOWING-DOWN SPECTROSCOPY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Leon E.; Anderson, Kevin K.; Gesh, Christopher J.

2010-08-11

Direct measurement of Pu in spent nuclear fuel remains a key challenge for safeguarding nuclear fuel cycles of today and tomorrow. Lead slowing-down spectroscopy (LSDS) is an active nondestructive assay method that has the potential to provide independent, direct measurement of Pu and U isotopic mass with an uncertainty lower than the approximately 10 percent typical of today’s confirmatory assay methods. Pacific Northwest National Laboratory’s (PNNL) previous work to assess the viability of LSDS for the assay of pressurized water reactor (PWR) assemblies indicated that the method could provide direct assay of Pu-239 and U-235 (and possibly Pu-240 and Pu-241)more » with uncertainties less than a few percent, assuming suitably efficient instrumentation, an intense pulsed neutron source, and improvements in the time-spectra analysis methods used to extract isotopic information from a complex LSDS signal. This previous simulation-based evaluation used relatively simple PWR fuel assembly definitions (e.g. constant burnup across the assembly) and a constant initial enrichment and cooling time. The time-spectra analysis method was founded on a preliminary analytical model of self-shielding intended to correct for assay-signal nonlinearities introduced by attenuation of the interrogating neutron flux within the assembly.« less

Extension of the Bgl Broad Group Cross Section Library

NASA Astrophysics Data System (ADS)

Kirilova, Desislava; Belousov, Sergey; Ilieva, Krassimira

2009-08-01

The broad group cross-section libraries BUGLE and BGL are applied for reactor shielding calculation using the DOORS package based on discrete ordinates method and multigroup approximation of the neutron cross-sections. BUGLE and BGL libraries are problem oriented for PWR or VVER type of reactors respectively. They had been generated by collapsing the problem independent fine group library VITAMIN-B6 applying PWR and VVER one-dimensional radial model of the reactor middle plane using the SCALE software package. The surveillance assemblies (SA) of VVER-1000/320 are located on the baffle above the reactor core upper edge in a region where geometry and materials differ from those of the middle plane and the neutron field gradient is very high which would result in a different neutron spectrum. That is why the application of the fore-mentioned libraries for the neutron fluence calculation in the region of SA could lead to an additional inaccuracy. This was the main reason to study the necessity for an extension of the BGL library with cross-sections appropriate for the SA region. Comparative analysis of the neutron spectra of the SA region calculated by the VITAMIN-B6 and BGL libraries using the two-dimensional code DORT have been done with purpose to evaluate the BGL applicability for SA calculation.

LWR pressure vessel surveillance dosimetry improvement program: LWR power reactor surveillance physics-dosimetry data base compendium

DOE Office of Scientific and Technical Information (OSTI.GOV)

McElroy, W.N.

1985-08-01

This NRC physics-dosimetry compendium is a collation of information and data developed from available research and commercial light water reactor vessel surveillance program (RVSP) documents and related surveillance capsule reports. The data represents the results of the HEDL least-squares FERRET-SAND II Code re-evaluation of exposure units and values for 47 PWR and BWR surveillance capsules for W, B and W, CE, and GE power plants. Using a consistent set of auxiliary data and dosimetry-adjusted reactor physics results, the revised fluence values for E > 1 MeV averaged 25% higher than the originally reported values. The range of fluence values (new/old)more » was from a low of 0.80 to a high of 2.38. These HEDL-derived FERRET-SAND II exposure parameter values are being used for NRC-supported HEDL and other PWR and BWR trend curve data development and testing studies. These studies are providing results to support Revision 2 of Regulatory Guide 1.99. As stated by Randall (Ra84), the Guide is being updated to reflect recent studies of the physical basis for neutron radiation damage and efforts to correlate damage to chemical composition and fluence.« less

Plasmon Spectroscopy Applied to Biomolecular Interactions in Membranes

NASA Astrophysics Data System (ADS)

Tollin, Gordon

2010-03-01

Plasmon-waveguide resonance (PWR) is an optical spectroscopy method that can provide information about materials immobilized on the surface of a plasmon resonator consisting of a right angle prism coated with thin layers of a metal (approx. 50 nm; usually silver) and a dielectric (approx. 500 nm; usually silica). The technique has been developed in our laboratory and is an extension of the more commonly used surface plasmon resonance (SPR) method, having higher sensitivity (20-50 fold) and resolution (10-20 fold). The dielectric layer allows plasmon excitation by light whose electric vector is polarized both perpendicular and parallel to the sensor surface, in contrast to SPR that can only utilize perpendicular polarized excitation. This allows both mass density and mass distribution to be characterized in uniaxially oriented deposited materials, such as biomembranes. We have utilized this technique to investigate binding interactions between membrane-incorporated protein receptors and their ligands (both proteins and small molecules), using both purified receptors inserted into lipid bilayers and membranes derived from cells expressing these receptors. Such studies have provided many new insights into biological signaling events. Inasmuch as many of these receptors are targets for approximately 50 percent of ethical drugs, PWR can be a useful methodology for drug discovery in the pharmaceutical industry. Examples of these experiments will be presented.

Conceptual Core Analysis of Long Life PWR Utilizing Thorium-Uranium Fuel Cycle

NASA Astrophysics Data System (ADS)

Rouf; Su'ud, Zaki

2016-08-01

Conceptual core analysis of long life PWR utilizing thorium-uranium based fuel has conducted. The purpose of this study is to evaluate neutronic behavior of reactor core using combined thorium and enriched uranium fuel. Based on this fuel composition, reactor core have higher conversion ratio rather than conventional fuel which could give longer operation length. This simulation performed using SRAC Code System based on library SRACLIB-JDL32. The calculation carried out for (Th-U)O2 and (Th-U)C fuel with uranium composition 30 - 40% and gadolinium (Gd2O3) as burnable poison 0,0125%. The fuel composition adjusted to obtain burn up length 10 - 15 years under thermal power 600 - 1000 MWt. The key properties such as uranium enrichment, fuel volume fraction, percentage of uranium are evaluated. Core calculation on this study adopted R-Z geometry divided by 3 region, each region have different uranium enrichment. The result show multiplication factor every burn up step for 15 years operation length, power distribution behavior, power peaking factor, and conversion ratio. The optimum core design achieved when thermal power 600 MWt, percentage of uranium 35%, U-235 enrichment 11 - 13%, with 14 years operation length, axial and radial power peaking factor about 1.5 and 1.2 respectively.

VizieR Online Data Catalog: Multiwavelength study of HII region S311 (Yadav+, 2016)

NASA Astrophysics Data System (ADS)

Yadav, R. K.; Pandey, A. K.; Sharma, S.; Ojha, D. K.; Samal, M. R.; Mallick, K. K.; Jose, J.; Ogura, K.; Richichi, A.; Irawati, P.; Kobayashi, N.; Eswaraiah, C.

2017-11-01

We observed the HII region S311 (centred on RA(2000)=07:52:24, DE(2000)=-26:24:58.40) in NIR broad-bands J (1.25um), H (1.63um) and Ks (2.14um) on 2010 March 3 using the Infrared Side Port Imager (ISPI) camera mounted on the CTIO Blanco 4-m telescope. We consider only those sources having error <0.1mag in all three bands, resulting in a final catalogue of 2671 point sources. The Spitzer-IRAC observations for the S311 region (PID 20726) were made on 2006 May 3 using the 3.6, 4.5, 5.8 and 8.0um bands and were downloaded from the Spitzer heritage archive (SHA). (4 data files).

Wideband response of a terahertz-millimeter imager based on a 384x288 pixel uncooled bolometric detector

NASA Astrophysics Data System (ADS)

Terroux, Marc; Marchese, Linda; Bolduc, Martin; Mercier, Luc; Chevalier, Claude; Gagnon, Lucie; Tremblay, Bruno; Généreux, Francis; Paultre, Jacques-Edmond; Provençal, Francis; Beaupré, Patrick; Desroches, Yan; Châteauneuf, François; Bergeron, Alain

2017-11-01

In the past, bolometer-based imagers have been used for earth observation. Uncooled-bolometer based imagers are especially well suited for this due to their low power consumption. NIRST (New Infra-Red Sensor Technology), an example of an imager based on uncooled bolometers, monitors high temperature events on the ground related to fires and volcanic events, and will measure their physical parameters and takes measurements of sea surface temperatures mainly off the coast of South America as well as other targeted opportunities. NIRST has one band in the mid-wave infrared centered at 3.8 um with a bandwidth of 0.8 um, and two bands in the thermal infrared, centered respectively at 10.85 and 11.85 um with a bandwidth of 0.9 um.

Urine Monitoring System

NASA Technical Reports Server (NTRS)

Feedback, Daniel L.; Cibuzar, Branelle R.

2009-01-01

The Urine Monitoring System (UMS) is a system designed to collect an individual crewmember's void, gently separate urine from air, accurately measure void volume, allow for void sample acquisition, and discharge remaining urine into the Waste Collector Subsystem (WCS) onboard the International Space Station. The Urine Monitoring System (UMS) is a successor design to the existing Space Shuttle system and will resolve anomalies such as: liquid carry-over, inaccurate void volume measurements, and cross contamination in void samples. The crew will perform an evaluation of airflow at the ISS UMS urinal hose interface, a calibration evaluation, and a full user interface evaluation. o The UMS can be used to facilitate non-invasive methods for monitoring crew health, evaluation of countermeasures, and implementation of a variety of biomedical research protocols on future exploration missions.

VizieR Online Data Catalog: UKIDSS-DR7 Large Area Survey (Lawrence+ 2011)

NASA Astrophysics Data System (ADS)

UKIDSS Consortium

2012-03-01

The UKIRT Infrared Deep Sky Survey (UKIDSS) is a large-scale near-IR survey which aim is to cover 7500 square degrees of the Northern sky. The survey is carried out using the Wide Field Camera (WFCAM), with a field of view of 0.21 square degrees, mounted on the 3.8m United Kingdom Infra-red Telescope (UKIRT) in Hawaii. The Large Area Survey (LAS) covers an area of 4000 square degrees in high Galactic latitudes (extragalactic) in the four bands Y(1.0um) J(1.2um) H(1.6um) and K(2.2um) to a depth of K = 18.4. Details of the survey can be found in the in the paper by Lawrence et al. (2007MNRAS.379.1599L) (1 data file).

Use of the University of Minnesota Biocatalysis/Biodegradation Database for study of microbial degradation

PubMed Central

2012-01-01

Microorganisms are ubiquitous on earth and have diverse metabolic transformative capabilities important for environmental biodegradation of chemicals that helps maintain ecosystem and human health. Microbial biodegradative metabolism is the main focus of the University of Minnesota Biocatalysis/Biodegradation Database (UM-BBD). UM-BBD data has also been used to develop a computational metabolic pathway prediction system that can be applied to chemicals for which biodegradation data is currently lacking. The UM-Pathway Prediction System (UM-PPS) relies on metabolic rules that are based on organic functional groups and predicts plausible biodegradative metabolism. The predictions are useful to environmental chemists that look for metabolic intermediates, for regulators looking for potential toxic products, for microbiologists seeking to understand microbial biodegradation, and others with a wide-range of interests. PMID:22587916

Misalignment tolerant efficient inverse taper coupler for silicon waveguide

NASA Astrophysics Data System (ADS)

Wang, Peng; Michael, Aron; Kwok, Chee Yee; Chen, Ssu-Han

2015-12-01

This paper describes an efficient fiber to submicron silicon waveguide coupling based on an inversely tapered silicon waveguide embedded in a SiO2 waveguide that is suspended in air. The inverse taper waveguide consist of a 50um long and 240nm thick silicon that linearly taper in width from 500nm to 120nm, which is embedded in SiO2. The SiO2 waveguide is 6um wide and 10um long. The simulation results show that the coupling loss of this new approach is 2.7dB including the interface loss at the input and output. The tolerance to fiber misalignment at the input of the coupler is 2um in both horizontal and vertical directions for only 1.5dB additional loss.

A Group of 500 Women Whose Health May Depart Notably From the Norm: Protocol for a Cross-Sectional Survey.

PubMed

Schnelle, Christoph; Minford, Eunice J; McHardy, Vanessa; Keep, Jane

2017-11-23

Longitudinal studies of women's health often seek to identify predictors of good health. Research has shown that following simple guidelines can halve women's mortality. The ongoing Australian Longitudinal Study of Women's Health (ALSWH) shows that Australian women are getting better at reducing their smoking and alcohol use, and are generally diligent about attending recommended health screenings, but are becoming less successful at dealing with obesity. There are communities of women who live unusually healthy lives (Rosetans, Seventh-Day Adventists, traditional Japanese women), but their lifestyles are unlikely to be adopted widely. Universal Medicine (UM) is a complementary-to-medicine approach that emphasizes personal empowerment and the importance of menstrual health symptoms. This survey investigates whether the approximately 500 women associated with UM exhibit health status significantly above the norm. As part of this investigation, questions for a newly developed menstrual attitudes questionnaire will also be evaluated. A quantitative cross-sectional survey of women in a UM cohort was designed with the help of three focus groups of women at three life stages: in menses, peri-menopausal, and menopausal. The menstrual attitudes portion of the survey incorporates the insights of these women regarding female health issues. The survey also includes 41 questions taken from the ALSWH. Focus groups generated additional questions about symptoms experienced and attitudes toward female health issues. ALSWH questions, including a range of health scales like the Short Form 36 (SF-36), Center for Epidemiologic Studies Depression Scale, Perceived Control Scale, Kessler Psychological Distress Scale, and the Multi-Item Summed Score for Perceived Stress, along with questions about experienced major health events, were investigated and incorporated if considered suitable. The validity of the menstrual attitudes questionnaire will be evaluated with Cohen's kappa. ALSWH respondents and UM participants will be compared, using unweighted regression or regression weighted or normalized by age, education, and interest in alternative treatments (to increase comparability), as appropriate. Analyses will determine whether UM-related variables (being a UM participant, length of UM participation, number of UM events attended) are associated with: differences in the number of major health events and health symptoms experienced; SF-36 physical and mental health scores; body mass index; and consumption of alcohol, tobacco, sugar, salt, caffeine, and dairy. If women in the UM cohort are truly in substantially better health than the norm, further investigations may be worthwhile to see whether UM plays a causal role, and whether the women's practices are generalizable. ©Christoph Schnelle, Eunice J Minford, Vanessa McHardy, Jane Keep. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 23.11.2017.

Hypermethylation of AP-2Alpha as a Prognostic Marker for DCIS

DTIC Science & Technology

2008-05-01

Unfortunately, among the methylation status of the AP2, CYCLIN D, ECAD , GSTP, and SSOCS genes, either as individual genes, or in combinations, no...0.61 to 4.10) 1.00 (referent) 0.35 ECAD M UM 0 100 3 97 GSTP M UM 40 60 24 76 2.02 (0.72 to 5.64) 1.00...Missing data: 1.4% for AP2, CYCLIN D, ECAD , GSTP; 4.2% for SSOCS; 2.8% for nuclear grade. §M=methylated; UM=unmethylated; +Two-sided

Attache Extraordinaire: Vernon A. Walters and Brazil

DTIC Science & Technology

2009-03-01

contudo, o primeiro encontro com um brasileiro. De acordo com uma entrevista que Walters concedeu, em 1966, ao Jornal O Globo, o primeiro brasileiro...21 de fevereiro de 1964, às 18 h, Lincoln Gordon enviou um telegrama ao Departamento de Estado. A mensagem dava conta de um encontro que o...disposição de Goulart em assumir riscos extremos, por meio do incentivo a violência esporádica no interior, encontros de grandes multidões e greves com o

Development of a universal metabolome-standard method for long-term LC-MS metabolome profiling and its application for bladder cancer urine-metabolite-biomarker discovery.

PubMed

Peng, Jun; Chen, Yi-Ting; Chen, Chien-Lun; Li, Liang

2014-07-01

Large-scale metabolomics study requires a quantitative method to generate metabolome data over an extended period with high technical reproducibility. We report a universal metabolome-standard (UMS) method, in conjunction with chemical isotope labeling liquid chromatography-mass spectrometry (LC-MS), to provide long-term analytical reproducibility and facilitate metabolome comparison among different data sets. In this method, UMS of a specific type of sample labeled by an isotope reagent is prepared a priori. The UMS is spiked into any individual samples labeled by another form of the isotope reagent in a metabolomics study. The resultant mixture is analyzed by LC-MS to provide relative quantification of the individual sample metabolome to UMS. UMS is independent of a study undertaking as well as the time of analysis and useful for profiling the same type of samples in multiple studies. In this work, the UMS method was developed and applied for a urine metabolomics study of bladder cancer. UMS of human urine was prepared by (13)C2-dansyl labeling of a pooled sample from 20 healthy individuals. This method was first used to profile the discovery samples to generate a list of putative biomarkers potentially useful for bladder cancer detection and then used to analyze the verification samples about one year later. Within the discovery sample set, three-month technical reproducibility was examined using a quality control sample and found a mean CV of 13.9% and median CV of 9.4% for all the quantified metabolites. Statistical analysis of the urine metabolome data showed a clear separation between the bladder cancer group and the control group from the discovery samples, which was confirmed by the verification samples. Receiver operating characteristic (ROC) test showed that the area under the curve (AUC) was 0.956 in the discovery data set and 0.935 in the verification data set. These results demonstrated the utility of the UMS method for long-term metabolomics and discovering potential metabolite biomarkers for diagnosis of bladder cancer.

In vivo monitoring of nanosphere onsite delivery using fiber optic microprobe

NASA Astrophysics Data System (ADS)

Lo, Leu-Wei; Yang, Chung-Shi

2005-02-01

To recognize the information of ischemia-induced blood vessel permeability would be valuable to formulate the drugs for optimal local delivery, we constructed an implantable needle type fiber-optic microprobe for the monitoring of in vivo fluorescent substances in anesthetized rats. This fiber-optic microprobe was composed of coaxial optical fibers and catheterized using a thin wall tubing of stainless steel (~400 um O.D. and ~300 um I.D.). The central fiber, with 100 um core diameter and 20 um cladding, coated with a 30 um layer of gold, was surrounded by 10 fibers with 50 um cores. The central fiber carried the light from the 488 nm Argon laser to the tissue while the surrounding fibers collected the emitted fluorescence to the detector. When the fiber-optic microprobe was placed in the solutions containing various concentrations of fluorescent nanospheres (20 nm), either with or without 10% lipofundin as optical phantom, nanosphere concentration-dependent responses of the fluorescence intensity were observed. The microprobe was then implanted into the liver and the brain of anesthetized rats to monitor the in situ extravasation of pre-administered fluorescent nanospheres from vasculature following the ischemic insults. Both the hepatic and cerebral ischemic insults showed immediate increases of the extracellular 20 nm fluorescent nanospheres. The implantable fiber-optic microprobe constructed in present study provides itself as a minimally-invasive technique capable of investigating the vascular permeability for in vivo nanosphere delivery in both ischemic liver and brain.

Targeted sections in either XY or XZ plane with dual-axes confocal endomicroscope (Conference Presentation)

NASA Astrophysics Data System (ADS)

Li, Gaoming; Li, Haijun; Duan, Xiyu; Zhou, Quan; Zhou, Juan; Oldham, Kenn R.; Wang, Thomas D.

2017-02-01

We demonstrate a dual axes confocal architecture, which can be used to collect horizontal(XY-plane) or vertical cross-sectional(XZ-plane) images for tissue. This scanner head is 5.5mm in outer diameter(OD), and integrates a 3D MEMS scanner with a compact chip size of 3.2×2.9mm2. To realize the miniaturization, there are some obstacles of the small size of 3D MEMS scanner, MEMS wire bundle, the air pressure effect for MEMS motion, the processing of parabolic mirror, and optical alignment to come over. In our probe, separation mechanical structure for optical alignment was adopted and a step shape MEMS holder was designed to deal with the difficult of MEMS wire bundle. Peptides have been demonstrated tremendous potential for in vivo use to detect colonic dysplasia. This class of in vivo molecular probe can be labeled with near-infrared (NIR) dyes for visualizing the full depth of the epithelium in small animals. To confirm our probe performance, we take use of USAF 1951 resolution target to test its lateral and axial resolution. It has lateral and axial resolution of 2.49um and 4.98um, respectively. When we collect the fluorescence imaging of colon, it shows that the field of view are 1000um×1000um (horizontal) and 1000um×430um (vertical). The horizontal and vertical cross-sectional images of fresh mouse colonic mucosa demonstrate imaging performance with this miniature instrument.

Waves of the Future (for Mars): In-Situ Mid-infrared, Near-infrared, and Visible Spectroscopic Analysis of Antarctic Cryptoendolithic Communities.

NASA Astrophysics Data System (ADS)

Hand, K. P.; Calrson, R.; Sun, H.; Anderson, M.; Wynn, W.; Levy, R.

2005-12-01

We have analyzed both the surface expression and depth profile of cryptoendolithic microbial communities at Battleship Promontory, in the Dry Valleys of Antarctica. Data was collected on site with an active mid-infrared Fourier transform microspectrometer (2.6 - 15 um), a near-infrared spectrometer (0.9-1.8 um), and a visible spectrometer (0.4-1 um). The trio of instruments are connected to microscopes that yield ~1 mm2 spatial resolution on the sample and they are mounted on two perpendicular motorized stages that allow for spatial scanning over an area of ~2cm2. Here we present results on the surface expression of the subsurface microbes in these three spectral regions and we present results on the analysis of a colonized sample examined in cross section. The former case has direct application to the remote, robotic detection of life within the rocks of Mars and the later case provides fundamental insights into the geological and biological interactions that make the Antarctic cryptoendolithic ecosystems possible. Non-invasive surface detection of cyanobacterial dominated communities was possible through the observation of several distinct bands: the carbon-hydrogen stretching modes (symmetric and asymmetric) for CH, CH2, and CH3 in the regions of 3.3-3.6 um and 3.6-3.7 um; the NH2 scissoring and C=O stretch near 6.0 um; the amide I of beta-pleated structures at ~6.1 um; and the 6.4 um - 6.6 um bands of N-H in plane bend of the amide II functional group. In combination, these bands make a strong case for carbohydrates and proteins associated with life. Not surprisingly, as the integrity of the amorphous silica surface varnish improved, our ability to detected the subsurface biosignature decreased. We note, however, that by utilizing the JPL rock crusher in Antarctica, a device designed to fly on the Mars Science Laboratory mission, the mid-infrared biosignature was easily detected. In the cross-section analysis the mid-infrared data provide a depth profile tracking the presence of hydrocarbons, amide bonds, and the mineralogical transition from amorphous quartz to crystalline sandstone. Mapped onto this are the changes in the oxidation states of iron, as recorded by the visible and near-infrared spectrometers. Together, this data set allows us to track the role of biologically produced compounds, such as oxalic acid, in the chelation and leaching of iron compounds from the surface through the rock and into the deposition zone below the colonized subsurface region.

Conclusions and Recommendations Regarding the Deep Sea Hybrid Power Systems Initial Study

DTIC Science & Technology

2010-06-01

proton-exchange membrane fuel cells ( PEMFC ) powered with hydrogen and oxygen, similar to that used on proven subsurface vessels; (2) fuel-cells...AND STORAGE OPTIONS CONSIDERED FOR INITIAL STUDY NO. NOMENCLATURE DESCRIPTION 1 PWR Nuclear Reactor + Battery 2 FC1 PEMFC + Line for surface O2...Wellhead Gas + Reformer + Battery 3 FC2 PEMFC + Stored O2 + Wellhead Gas + Reformer + Battery 4 SV1 PEMFC + Submersible Vehicle for O2 Transport

VizieR Online Data Catalog: 70um-1.2mm and N2H+ maps of IRDC18454 (W43) (Beuther+,

NASA Astrophysics Data System (ADS)

Beuther, H.; Tackenberg, J.; Linz, H.; Henning, T.; Krause, O.; Ragan, S.; Nielbock, M.; Launhardt, R.; Schmiedeke, A.; Schuller, F.; Carlhoff, P.; Nguyen-Luong, Q.; Sakai, T.

2011-11-01

The cloud complex with a size of ~6'x6' was observed with PACS on Herschel on 2010 March 9. Maps at 250, 350, and 500um were obtained with SPIRE 2010) on 2010 March 11. We observed IRDC18454-1 with the Plateau de Bure Interferometer during five nights in October and November 2009 at 93GHz in the C and D configurations. The N2H+ data has been observed using the BEARS receiver at the NRO 45m telescope in Nobeyama, Japan. The different velocity components have been observed one in April 2010 with an average system temperature of Tsys=206K, the second in June, at slightly lower Tsys. The MIPS 24um data (from MIPSGAL) as well as the IRAC 8um observations (from GLIMPSE) are taken from the Spitzer archive. The 1.2mm continuum data were first presented in Beuther et al. (2002, Cat. J/ApJ/566/945) and the APEX 870um data are part of the ATLASGAL survey of the Galactic plane (Schuller et al., 2009A&A...504..415S). (2 data files).

Heterologous production and characterization of a chlorogenic acid esterase from Ustilago maydis with a potential use in baking.

PubMed

Nieter, Annabel; Kelle, Sebastian; Takenberg, Meike; Linke, Diana; Bunzel, Mirko; Popper, Lutz; Berger, Ralf G

2016-10-15

Ustilago maydis, an edible mushroom growing on maize (Zea mays), is consumed as the food delicacy huitlacoche in Mexico. A chlorogenic acid esterase from this basidiomycete was expressed in good yields cultivating the heterologous host Pichia pastoris on the 5L bioreactor scale (reUmChlE; 45.9UL(-1)). In contrast to previously described chlorogenic acid esterases, the reUmChlE was also active towards feruloylated saccharides. The enzyme preferred substrates with the ferulic acid esterified to the O-5 position of arabinose residues, typical of graminaceous monocots, over the O-2 position of arabinose or the O-6 position of galactose residues. Determination of kcat/Km showed that the reUmChlE hydrolyzed chlorogenic acid 18-fold more efficiently than methyl ferulate, p-coumarate or caffeate. Phenolic acids were released by reUmChlE from natural substrates, such as destarched wheat bran, sugar beet pectin and coffee pulp. Treatment of wheat dough using reUmChlE resulted in a noticeable softening indicating a potential application of the enzyme in bakery and confectionery. Copyright © 2016 Elsevier Ltd. All rights reserved.

3D brain oxygenation measurements in awake hypertensive mice using two photon phosphorescence lifetime imaging

NASA Astrophysics Data System (ADS)

Lu, Xuecong; Moeini, Mohammad; Li, Baoqiang; Zhang, Cong; Sakadžić, Sava; Lesage, Frédéric

2018-02-01

Cardiovascular risk factors, such as hypertension, have been associated with cognitive decline, potentially due to their impact on brain tissue oxygenation. In this study, high spatial resolution imaging in three dimensions was used to understand changes in brain oxygenation with hypertension. Experiments were performed on Young (WT_Y, 3-4 months, n=8), Old (WT_O, 6-7 months, n=8), and Old with hypertension (HP_O, 6-7 months, n=8) C57bL/6 awake mice. Two photon phosphorescence lifetime microscopy using an O2-sensitive phosphorescent dye PtPC343 was employed to measure two dimensional grids of PO2 in capillary beds (400um*400um, 25*25 pixels, acquired in 4 mins) and decays from arterioles. Scans were obtained continuously at depths from 50 um to 300 um under the brain surface. Using 3D measurements and a 250 um depth stack, we removed the compounding effects on brain oxygenation diffusion from surrounding brain vessels. The entire measurement of each vasculature stack required less than 30 minutes. This study indicates that among vascular risk factors, hypertension can reduce oxygen delivery and could potentially contribute to cognition decline.

Spitzer/IRS spectroscopy of the 12um Seyferts

NASA Astrophysics Data System (ADS)

Wu, Yanling; Charmandaris, V.; Huang, J.; Houck, J.

2009-01-01

The extended 12um galaxy sample is a flux-limited sample of 893 galaxies selected from the IRAS Faint Source Catalog 2. A total of 118 objects from this sample have been classified optically as Seyfert galaxies, providing one of the largest infrared selected unbiased sample of active galactic nuclei (AGN). We present our prelimary results from our analysis of mid-infrared Spitzer/IRS spectra of 102 12um Seyferts (that is 86 % of the 12um Seyfert sample) which have been observed by various Spitzer programs and are available in the Spitzer archive. A number of mid-infared diagnostics have been developed to study the nature of nuclear dust enshrouded emission from AGNs, in order to disentangle the starburst-AGN connection. Since PAH emission is a tracer of star formation activity we have measured the 11.3um PAH feature for our Seyfert sample. We find that as the strength of the radiation field in AGNs increases the PAH molecules are destroyed, while the PAH EWs increase with the IRAS f60/f25 ratios of the host galaxies. We further probe this warm/cold color diagnostic, by contrasting our findings with those of we starbust galaxies, ULIRGs, as well as blue compact dwarf galaxies.

(QC Themes) Type-Two Quantum Computing in PBG-Based Cavities for Efficient Simulation of Lattice Gas Dynamics

DTIC Science & Technology

2008-04-26

substrate Si3N4 Diameter : 540 nm Pitch : 760 nm Diamond Holes in Diamond (HID) Pillars of Diamond (POD) POD with Electrooptic Polymer at Center 3D ...Diamond film : 2 um Si- substrate Al : 0.2 um PMMA : 0.5um 1. Deposit UNCD film 2. Deposit Al metal 3. Deposit PMMA on Al 4. E-beam Lithography 5...band-gap (PBG) based cavities. The cavities are etched directly on to the diamond substrate . The set of coupled qubits in each spot represents an

Direct hip joint distraction during acetabular fracture surgery using the AO universal manipulator.

PubMed

Calafi, L Afshin; Routt, M L Chip

2010-02-01

Certain acetabular fractures may necessitate distraction of the hip joint for removal of intra-articular debris and assessment of reduction. Distraction can be accomplished by manual traction, using a traction table or an AO universal manipulator (UM). The UM is a relatively simple and an inexpensive device that can provide focal distraction in a controlled manner without the risks associated with the use of a traction table. We describe a technique using the UM for hip joint distraction during acetabular fracture surgery through a Kocher-Langenbeck surgical exposure.

PERSONALITY TRAITS AND STRESS LEVELS AMONG SENIOR DENTAL STUDENTS: EVIDENCE FROM MALAYSIA AND SINGAPORE.

PubMed

Yusof, Zamros Y M; Hassan, Wan Nurazreena Wan; Razak, Ishak A; Hashim, Siti Marini N; Tahir, Mohd Khairul A M; Keng, Siong Beng

2016-11-01

This study aimed to evaluate the association between dental students’ personality traits and stress levels in relation to dental education programs among senior dental students in University Malaya (UM) in Malaysia and National University of Singapore (NUS). A cross-sectional survey using a self-administered questionnaire was conducted on UM and NUS senior dental students. The questionnaire comprised items on demographic background, the Big Five Inventory Personality Traits (BFIPT) test and a modified Dental Environment Stress (DES) scale. Rasch analysis was used to convert raw data to interval scores. Analyses were done by t-test, Pearson correlation, and Hierarchical regression statistics. The response rate was 100% (UM=132, NUS=76). Personality trait Agreeableness (mean=0.30) was significantly more prevalent among UM than NUS students (mean=0.15, p=0.016). In NUS, Neuroticism (mean=0.36) was significantly more prevalent than in UM (mean=0.14, p=0.002). The DES mean score was higher among NUS (mean=0.23) than UM students (mean=0.07). In UM, Neuroticism was significantly correlated with stress levels (r=0.338, p<0.001). In NUS, these were Neuroticism (r=0.278, p=0.015), Agreeableness (r=0.250, p=0.029) and Conscientiousness (r=-0.242, p=0.035) personality traits. The correlation was strongest for personality trait Neuroticism in both schools. Hierarchical regression analysis showed that gender and Neuroticism were significant predictors for students’ stress levels (p<0.05) with the latter exerting a bigger effect size (R2=0.18) than gender (R2=004). This study showed that gender and Neuroticism personality trait were significant predictors for stress levels among selected groups of dental students in Southeast Asia. Information on students’ personality may be useful in new students’ intake, stress management counseling and future program reviews.

Development of an In-line Urine Monitoring System for the International Space Station

NASA Technical Reports Server (NTRS)

Broyan, James Lee, Jr.; Cibuzar, Branelle R.

2009-01-01

Exposure to microgravity during space flight causes bone loss when calcium and other metabolic by-products are excreted in urine voids. Frequent and accurate measurement of urine void volume and constituents is thus essential in determining crew bone loss and the effectiveness of the countermeasures that are taken to minimize this loss. Earlier space shuttle Urine Monitoring System (UMS) technology was unable to accurately measure urine void volumes due to the cross-contamination that took place between users, as well as to fluid system instabilities. Crew urine voids are currently collected manually in a flexible plastic bag that contains a known tracer quantity. A crew member must completely mix the contents of this bag before withdrawing a representative syringe sample for later ground analysis. The existing bag system accuracy is therefore highly dependent on mixing technique. The International Space Station (ISS) UMS has been developed as an automated device that collects urine from the Waste and Hygiene Compartment (WHC) urinal funnel interface, separates the urine, measures void volume, and allows for syringe sampling. After the ISS UMS has been used by a crew member, it delivers urine to the WHC for normal processing. The UMS plumbing is then flushed with a small volume of water. The current ISS UMS design incorporates an innovative rotary separator that minimizes foaming, consequently greatly reducing cross-contamination among urine voids (less than 0.5 mL urine) while also providing accurate volume measurements (less than 2 percent error for 100 to 1,000 mL void volumes). ISS UMS performance has been validated through extensive ground tests and reduced-gravity aircraft flights. The locker-sized ISS UMS is currently undergoing a design modification that will permit it to interface with the ISS Node 3 WHC Russian toilet (ACY) hardware. The operating principles, characteristics, and results of this design modification are outlined here.

An indirect continuous running multistage field test: the Université de Montréal track test.

PubMed

Léger, L; Boucher, R

1980-06-01

The object of this study was to report on the validity and reliability of the Université de Montréal Track Test (UM-TT). The UM-TT is a continuous maximal indirect multistage running field test based on the energy cost of running. The first stage is set at a walking speed that requires 5 Mets; thereafter the speed is increased by 1 Met every two minutes. In order to assess the validity of the UM-TT, 25 subjects, 24.4 +/- 2.8 years old (X +/- SD) had their VO2max predicted with the UM-TT and measured directly with a running multistage treadmill test. Averages (+/- SD) were not significantly different (61.5 +/- 10.6 and 61.4 +/- 10.9 ml O2 . kg-1 . min-1, respectively), other statistics being r = 0.96, delta = 0.09 +/- 2.90 ml O2 . kg-1 . min-1 and Syx = 2.81 ml O2 . kg-1 . min-1. Seven males, 20.6 +/- 1.0 years old, had also their VO2max measured directly during the UM-TT. Comparison of predicted and directly measured VO2max yielded similar results: 70.0 +/- 4.5 and 70.7 +/- 6.0 ml O2 . kg-1 . min-1, respectively with r = 0.66, delta = 0.67 +/- 4.53 and Syx = 3.71. Reliability of the UM-TT was assessed by repeating the test twice on 60 subjects (49 males and 11 females; 39 subjects below 30 years old and 21, above; and 30 subjects below and above 15 Mets). Results were as follows: X +/- SD = 54.1 +/- 8.2 and 54.2 +/- 8.5, r = 0.97, delta 0.11 +/- 1.92, and Syx = 1.92. Similar reliability trends were observed for each one of the subgroups of subjects. It is concluded that the UM-TT is valid and reliable to estimate the VO2max of trained and untrained young and middle-age males and females.

Long-Term Satisfaction and Body Image After Contralateral Prophylactic Mastectomy

PubMed Central

Anderson, Chelsea; Islam, Jessica Y.; Hodgson, M. Elizabeth; Sabatino, Susan A.; Rodriguez, Juan L.; Lee, Clara N.; Sandler, Dale P.; Nichols, Hazel B.

2017-01-01

Background Contralateral prophylactic mastectomy (CPM) rates have been increasing in the U.S. Though some studies have reported high overall satisfaction among women who undergo CPM, it is unclear how long-term satisfaction differs from that of women who undergo unilateral mastectomy (UM). Furthermore, few studies have assessed whether the effects of CPM on body image differ from those of breast conserving surgery (BCS) or UM. Methods We analyzed responses from a survey of women with both a personal and family history of breast cancer who were enrolled in the Sister Study (n=1176). Among women who underwent mastectomy, satisfaction with mastectomy decision and reconstruction was compared between women who underwent CPM and UM. We also evaluated responses on 5 items related to body image according to surgery type (BCS, UM without reconstruction, CPM without reconstruction, UM with reconstruction, and CPM with reconstruction). Results Participants were, on average, 60.8 years old at diagnosis (SD=8.7) and 3.6 years post-diagnosis at the time of survey (SD=1.7). BCS was the most common surgical treatment reported (63%), followed by CPM (22%) and UM (15%). Satisfaction with mastectomy decision was reported by 97% of women who underwent CPM and 89% of those who underwent UM. Compared to other surgery types, women who underwent CPM without reconstruction reported feeling more self-conscious, less feminine, less whole, and less satisfied with the appearance of their breasts. Body image was consistently highest among women who underwent BCS. Conclusions In our sample of women with both a personal and family history of breast cancer, most were highly satisfied with their mastectomy decision, including those who elected to undergo CPM. However, body image was lowest among women who underwent CPM without reconstruction. Our findings may inform decisions among women considering various courses of surgical treatment. PMID:28058563

Colors and Compositional Characteristics of Kuiper Belt Objects and Centaurs

NASA Astrophysics Data System (ADS)

Lederer, S. M.; Vilas, F.; Jarvis, K. S.; French, L.

2001-11-01

We present a study designed by Painter et al. (DPS 2000) to search for evidence of aqueous alteration in the surface material of solar system objects. Using VRI broadband photometry, we will search for the presence of the 0.7 um absorption feature (indicative of Fe-bearing hydrated silicates) in KBOs and Centaurs. Vilas (Icarus 111, 1994) found a strong correlation between the presence of the 0.7-um feature in low-albedo asteroids with solar-like colors and the 3-um water of hydration feature, indicative of phyllosilicates. Recent work by Howell et al. (LPSC, 2001) confirms that the presence of the 0.7 um feature in low-albedo asteroids definitely indicates the presence of the 3.0-um water of hydration absorption feature, suggesting the action of aqueous alteration in asteroids. In addition, Feierberg et al. (Icarus 63, 1985) showed that when the U - B color difference is > 0.12 in ECAS photometry, the 3.0-um absorption feature is often present in low albedo asteroids. Therefore, if the U-B color difference is > 0.12 and the 0.7-um feature is present in UBVRI reflectance photometry, water of hydration is implied in KBOs and Centaurs. We pursue these studies based on the mixed flat or steeply reddened photometry of these objects: Water ice has been identified in near-IR dark, flat spectra of some Centaurs, providing a source for the action of aqueous alteration. The complex collisional history proposed for these objects suggests a potential source of heating that would melt water ice, providing a mechanism for aqueous alteration to occur. Finally, we will use BVR photometry to determine the B-V and V-R colors, as has been done by Tegler and Romanishin (Nature, 407). We will compare our results with colors of KBOs and Centaurs published in the literature. This research was supported by the National Research Council and the NASA Planetary Astronomy Program.

VizieR Online Data Catalog: Galactic CHaMP. II. Dense gas clumps. (Ma+, 2013)

NASA Astrophysics Data System (ADS)

Ma, B.; Tan, J. C.; Barnes, P. J.

2015-04-01

A total of 303 dense gas clumps have been detected using the HCO+(1-0) line in the CHaMP survey (Paper I, Barnes et al. 2011, J/ApJS/196/12). In this article we have derived the SED for these clumps using Spitzer, MSX, and IRAS data. The Midcourse Space Experiment (MSX) was launched in 1996 April. It conducted a Galactic plane survey (0

High frequency of CYP2D6 ultrarapid metabolizer genotypes in an Ashkenazi Jewish population from Argentina.

PubMed

Moya, G; Dorado, P; Ferreiro, V; Naranjo, M E G; Peñas-Lledó, E M; LLerena, A

2017-07-01

A twofold higher frequency of CYP2D6 ultrarapid metabolizers (estimated from genotype: gUMs) was reported among Ashkenazi Jews (AJ) living in New York (USA) than in other North American Caucasians, which might be important to guide the prescription for CYP2D6 substrates in AJ communities around the world. This study was aimed to determine whether the high frequency of CYP2D6 gUMs described in AJ from USA was replicated in AJ from Argentina when compared with other multiethnic admixture Argentines (GA). The frequency of the most common allelic variants and of CYP2D6 gUMs (>2 active genes) and poor metabolizers (0 active genes, gPMs) was also compared among the studied Argentine populations. CYP2D6 genotyping was performed in 173 AJ and 246 GA DNA samples of unrelated donors from the metropolitan area of Buenos Aires. CYP2D6 alleles (*2, *3, *4, *5, *6, *10, *17, *35, *41 and multiple copies), genotypes and functional phenotype frequencies were determined. The frequencies of gUMs and gPMs in AJ from Argentina were 11.5% and 5.2%, respectively, whereas in GA, the frequencies of gUM and gPMs were 6.5% and 4.9%, respectively. Comparisons between AJ and GA showed that gUMs frequencies were twofold higher (P<0.05) in AJ than GA. CYP2D6*35 allele was more frequent in GA than AJ, whereas CYP2D6*41 and *1xN were more frequent in AJ than in GA (P<0.05). This study supports the previously reported high frequency of gUMs on another Ashkenazi population in New York. The present findings also support the interethnic variability of CYP2D6 genetic polymorphism in the overall Argentine population.

VizieR Online Data Catalog: [CII] emission in the ISM of 20 nearby galaxies (Croxall+, 2017)

NASA Astrophysics Data System (ADS)

Croxall, K. V.; Smith, J. D.; Pellegrini, E.; Groves, B.; Bolatto, A.; Herrera-Camus, R.; Sandstrom, K. M.; Draine, B.; Wolfire, M. G.; Armus, L.; Boquien, M.; Brandl, B.; Dale, D.; Galametz, M.; Hunt, L.; Kennicutt, R.; Kreckel, K.; Rigopoulou, D.; van der Werf, P.; Wilson, C.

2018-04-01

Our observations include photometric and spectral-line observations from both the PACS and SPIRE instruments onboard Herschel, obtained as part of the large KINGFISH (Key Insights on Nearby Galaxies: a Far- Infrared Survey with Herschel, Kennicutt+ 2011PASP..123.1347K) and BtP (Beyond the Peak; OT1_jsmith1; P.I. J.D. Smith) projects. [NII]205um BtP observations were performed with SPIRE-FTS intermediate mapping, which is a 4-point dither. E. Pellegrini et al. (2017, in preparation) will contain a full description of the observations and reductions. [CII]158um and [NII]122um emission lines, and 70 and 160um continuum maps have been observed as part the Herschel Open Time Key Program KINGFISH. The data and the associated reduction are described in Kennicutt+ (2011PASP..123.1347K) and Croxall+ (2013ApJ...777...96C). (2 data files).

Development of a compact E ? B microchannel plate detector for beam imaging

DOE PAGES

Wiggins, B. B.; Singh, Varinderjit; Vadas, J.; ...

2017-06-17

A beam imaging detector was developed by coupling a multi-strip anode with delay line readout to an E×B microchannel plate (MCP) detector. This detector is capable of measuring the incident position of the beam particles in one-dimension. To assess the spatial resolution, the detector was illuminated by an α-source with an intervening mask that consists of a series of precisely-machined slits. The measured spatial resolution was 520 um source FWHM, which was improved to 413 um FWHM by performing an FFT of the signals, rejecting spurious signals on the delay line, and requiring a minimum signal amplitude. This measured spatialmore » resolution of 413 um FWHM corresponds to an intrinsic resolution of 334 um FWHM when the effect of the finite slit width is de-convoluted. To understand the measured resolution, the performance of the detector is simulated with the ion-trajectory code SIMION.« less

Development of a compact E ? B microchannel plate detector for beam imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiggins, B. B.; Singh, Varinderjit; Vadas, J.

A beam imaging detector was developed by coupling a multi-strip anode with delay line readout to an E×B microchannel plate (MCP) detector. This detector is capable of measuring the incident position of the beam particles in one-dimension. To assess the spatial resolution, the detector was illuminated by an α-source with an intervening mask that consists of a series of precisely-machined slits. The measured spatial resolution was 520 um source FWHM, which was improved to 413 um FWHM by performing an FFT of the signals, rejecting spurious signals on the delay line, and requiring a minimum signal amplitude. This measured spatialmore » resolution of 413 um FWHM corresponds to an intrinsic resolution of 334 um FWHM when the effect of the finite slit width is de-convoluted. To understand the measured resolution, the performance of the detector is simulated with the ion-trajectory code SIMION.« less

Dysregulated GPCR Signaling and Therapeutic Options in Uveal Melanoma

PubMed Central

Chua, Vivian; Lapadula, Dominic; Randolph, Clinita; Benovic, Jeffrey L.; Wedegaertner, Philip; Aplin, Andrew E.

2017-01-01

Uveal melanoma (UM) is the most common primary intraocular malignant tumor in adults and arises from the transformation of melanocytes in the uveal tract. Even after treatment of the primary tumor, up to 50% of patients succumb to metastatic disease. The liver is the predominant organ of metastasis. There is an important need to provide effective treatment options for advanced stage UM. In order to provide the preclinical basis for new treatments, it is important to understand the molecular underpinnings of the disease. Recent genomic studies have shown that mutations within components of G protein-coupled receptor (GPCR) signaling are early events associated with ~98% of UMs. Implications This review discusses the alterations in GPCR signaling components (GNAQ and GNA11), dysregulated GPCR signaling cascades, and viable targeted therapies with the intent to provide insight into new therapeutic strategies in UM. PMID:28223438

A Student Authored Online Medical Education Textbook: Editing Patterns and Content Evaluation of a Medical Student Wiki

PubMed Central

Thompson, CL; Schulz1, Wade L.; Terrence, Adam

2011-01-01

The University of Minnesota medical student wiki (UMMedWiki) allows students to collaboratively edit classroom notes to support medical education. Since 2007, UMMedWiki has grown to include 1,591 articles that have collectively received 1.2 million pageviews. Although small-scale wikis have become increasingly important, little is known about their dynamics compared to large wikis, such as Wikipedia. To better understand UMMedWiki’s management and its potential reproducibility at other medical schools, we used an edit log with 28,000 entries to evaluate the behavior of its student editors. The development of tools to survey UMMedwiki allows for quality comparisons that improve both the wiki and the curriculum itself. We completed a content survey by comparing the UMMedWiki with two types of rubric data: TIME, a medical education taxonomy consisting of 1500 terms and national epidemiological data on 2,100 diseases. PMID:22195202

Whole-Genome Sequencing and Comparative Analysis of Mycobacterium brisbanense Reveals a Possible Soil Origin and Capability in Fertiliser Synthesis.

PubMed

Wee, Wei Yee; Tan, Tze King; Jakubovics, Nicholas S; Choo, Siew Woh

2016-01-01

Mycobacterium brisbanense is a member of Mycobacterium fortuitum third biovariant complex, which includes rapidly growing Mycobacterium spp. that normally inhabit soil, dust and water, and can sometimes cause respiratory tract infections in humans. We present the first whole-genome analysis of M. brisbanense UM_WWY which was isolated from a 70-year-old Malaysian patient. Molecular phylogenetic analyses confirmed the identification of this strain as M. brisbanense and showed that it has an unusually large genome compared with related mycobacteria. The large genome size of M. brisbanense UM_WWY (~7.7Mbp) is consistent with further findings that this strain has a highly variable genome structure that contains many putative horizontally transferred genomic islands and prophage. Comparative analysis showed that M. brisbanense UM_WWY is the only Mycobacterium species that possesses a complete set of genes encoding enzymes involved in the urea cycle, suggesting that this soil bacterium is able to synthesize urea for use as plant fertilizers. It is likely that M. brisbanense UM_WWY is adapted to live in soil as its primary habitat since the genome contains many genes associated with nitrogen metabolism. Nevertheless, a large number of predicted virulence genes were identified in M. brisbanense UM_WWY that are mostly shared with well-studied mycobacterial pathogens such as Mycobacterium tuberculosis and Mycobacterium abscessus. These findings are consistent with the role of M. brisbanense as an opportunistic pathogen of humans. The whole-genome study of UM_WWY has provided the basis for future work of M. brisbanense.

Patterns of morphological variation in enamel–dentin junction and outer enamel surface of human molars

PubMed Central

Morita, Wataru; Yano, Wataru; Nagaoka, Tomohito; Abe, Mikiko; Ohshima, Hayato; Nakatsukasa, Masato

2014-01-01

Tooth crown patterning is governed by the growth and folding of the inner enamel epithelium (IEE) and the following enamel deposition forms outer enamel surface (OES). We hypothesized that overall dental crown shape and covariation structure are determined by processes that configurate shape at the enamel–dentine junction (EDJ), the developmental vestige of IEE. This this hypothesis was tested by comparing patterns of morphological variation between EDJ and OES in human permanent maxillary first molar (UM1) and deciduous second molar (um2). Using geometric morphometric methods, we described morphological variation and covariation between EDJ and OES, and evaluated the strength of two components of phenotypic variability, canalization and morphological integration, in addition to the relevant evolutionary flexibility, i.e. the ability to respond to selective pressure. The strength of covariation between EDJ and OES was greater in um2 than in UM1, and the way that multiple traits covary between EDJ and OES was different between these teeth. The variability analyses showed that EDJ had less shape variation and a higher level of morphological integration than OES, which indicated that canalization and morphological integration acted as developmental constraints. These tendencies were greater in UM1 than in um2. On the other hand, EDJ and OES had a comparable level of evolvability in these teeth. Amelogenesis could play a significant role in tooth shape and covariation structure, and its influence was not constant among teeth, which may be responsible for the differences in the rate and/or period of enamel formation. PMID:24689536

Delivering informatics capabilities to an AHC research community through public/private partnerships (PPP).

PubMed

Smith, Kevin A; Athey, Brian D; Chahal, Amar P S; Sahai, Priti

2008-11-06

Velos eResearch is a commercially-developed, regulatory-compliant, web-based clinical research information system from Velos Inc. Aithent Inc. is a software development services company. The University of Michigan (UM) has public/private partnerships with Velos and Aithent to collaborate on development of additional capabilities, modules, and new products to better support the needs of clinical and translational research communities. These partnerships provide UM with a mechanism for obtaining high-quality functionally comprehensive capabilities more quickly and at lower cost, while the corporate partners get a quality advisory and development partner--this benefits all parties. The UM chose to partner with Velos in part because of its commitment to interoperability. Velos is an active participant in the NCI caBIG project and is committed to caBIG compatibility. Velos already provides interoperability with other Velos sites in the CTSA context. One example of the partnership is co-development of integrated specimen management capabilities. UM spent more than a year defining business requirements and technical specifications for, and is funding development of, this capability. UM also facilitates an autonomous user community (20+ institutions, 7 CTSA awardees); the broad goal of the group is to share experiences, expertise, identify collaborative opportunities, and support one another as well as provide a source of future needs identification to Velos. Advantages and risks related to delivering informatics capabilities to an AHC research community through a public/private partnership will be presented. The UM, Velos and Aithent will discuss frameworks, agreements and other factors that have contributed to a successful partnership.

Clinical analysis of a large kindred with the pallister ulnar-mammary syndrome

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bamshad, M.; Root, S.; Carey, J.C.

1996-11-11

The ulnar-mammary syndrome (UMS) is an autosomal dominant disorder characterized by posterior limb deficiencies or duplications, apocrine/mammary gland hypoplasia and/or dysfunction, abnormal dentition, delayed puberty in males, and genital anomalies. We present the clinical descriptions of 33 members of a six generation kindred with UMS. The number of affected individuals in this family is more than the sum of all previously reported cases of UMS. The clinical expression of UMS is highly variable. While most patients have limb deficiencies, the range of abnormalities extends from hypoplasia of the terminal phalanx of the 5th digit to complete absence of the ulnamore » and 3rd, 4th, and 5th digits. Moreover, affected individuals may have posterior digital duplications with or without contralateral limb deficiencies. Apocrine gland abnormalities range from diminished axillary perspiration with normal breast development and lactation, to complete absence of the breasts and no axillary perspiration. Dental abnormalities include misplaced or absent teeth. Affected males consistently undergo delayed puberty, and both sexes have diminished to absent axillary hair. Imperforate hymen were seen in some affected women. A gene for UMS was mapped to chromosome area 12q23-q24.1. A mutation in the gene causing UMS can interfere with limb patterning in the proximal/distal, anterior/posterior, and dorsal/ventral axes. This mutation disturbs development of the posterior elements of forearm, wrist, and hand while growth and development of the anterior elements remain normal. 24 refs., 4 figs., 1 tab.« less

Effect of lifestyle interventions of pregnant women on their dietary habits, lifestyle behaviors, and weight gain: a randomized controlled trial.

PubMed

Aşcı, Özlem; Rathfisch, Gülay

2016-02-24

Although it is known that lifestyle behaviors of pregnant women are closely related to maternal and fetal health, number of data concerning efficacy of intervention on lifestyle during pregnancy is limited. The purpose of this study is to determine the effect of lifestyle interventions on improving dietary habits and lifestyle behaviors, ensuring gestational weight gain (GWG) within recommended levels and limiting postpartum weight retention (PWR). The study was conducted as a randomized controlled trial in a family health center located in Istanbul, Turkey, between June 2011 and July 2012. The primary outcomes were GWG, and the proportion of pregnant women whose GWG was within the Institute of Medicine (IOM) guidelines. One hundred two pregnant women with gestation ≤12 weeks, age ≥18 years, gravidity ≤2, and who did not intend to lose weight in prepregnancy period were randomly included in this study as intervention (n = 51) and control (n = 51) groups. The study was completed with 45 women for each group. The control group received routine antenatal care. The intervention group was received an individualized lifestyle intervention focusing on healthy lifestyle, diet, exercise, and weight monitoring as four sessions at 12-15, 16-18, 20-24, and 37 weeks gestation. Lifestyle behaviors were evaluated with Health-Promoting Lifestyle Profile-II. Dietary habits were assessed by 3-day dietary recalls, and weight was followed from pregnancy until 6 weeks postpartum. The lifestyle interventions had a significant effect on improving lifestyle behaviors, protein intake, percentage of energy from protein, calcium, magnesium, iron, zinc, and vegetable intakes when adjusted for confounders (p < 0.05). The proportion of women who were within the IOM recommendations was higher in the intervention group (51.1 %) than in the control group (28.9 %) The odds ratio for GWG within IOM was statistically significant between the groups (OR = 0.59, 95 % CI, 0.45-0.72). There were no difference between groups in terms of the other dietary intakes, total GWG, and PWR (p > 0.05). Lifestyle intervention improves the lifestyle behaviors during pregnancy and increases the appropriate GWG for prepregnancy body mass index (BMI), but it has a limited effect in terms of improving dietary habits and has no effect on PWR.

Xenon-induced power oscillations in a generic small modular reactor

NASA Astrophysics Data System (ADS)

Kitcher, Evans Damenortey

As world demand for energy continues to grow at unprecedented rates, the world energy portfolio of the future will inevitably include a nuclear energy contribution. It has been suggested that the Small Modular Reactor (SMR) could play a significant role in the spread of civilian nuclear technology to nations previously without nuclear energy. As part of the design process, the SMR design must be assessed for the threat to operations posed by xenon-induced power oscillations. In this research, a generic SMR design was analyzed with respect to just such a threat. In order to do so, a multi-physics coupling routine was developed with MCNP/MCNPX as the neutronics solver. Thermal hydraulic assessments were performed using a single channel analysis tool developed in Python. Fuel and coolant temperature profiles were implemented in the form of temperature dependent fuel cross sections generated using the SIGACE code and reactor core coolant densities. The Power Axial Offset (PAO) and Xenon Axial Offset (XAO) parameters were chosen to quantify any oscillatory behavior observed. The methodology was benchmarked against results from literature of startup tests performed at a four-loop PWR in Korea. The developed benchmark model replicated the pertinent features of the reactor within ten percent of the literature values. The results of the benchmark demonstrated that the developed methodology captured the desired phenomena accurately. Subsequently, a high fidelity SMR core model was developed and assessed. Results of the analysis revealed an inherently stable SMR design at beginning of core life and end of core life under full-power and half-power conditions. The effect of axial discretization, stochastic noise and convergence of the Monte Carlo tallies in the calculations of the PAO and XAO parameters was investigated. All were found to be quite small and the inherently stable nature of the core design with respect to xenon-induced power oscillations was confirmed. Finally, a preliminary investigation into excess reactivity control options for the SMR design was conducted confirming the generally held notion that existing PWR control mechanisms can be used in iPWR SMRs with similar effectiveness. With the desire to operate the SMR under the boron free coolant condition, erbium oxide fuel integral burnable absorber rods were identified as a possible means to retain the dispersed absorber effect of soluble boron in the reactor coolant in replacement.

The International Space Station Urine Monitoring System (UMS)

NASA Technical Reports Server (NTRS)

Feeback, Daniel L.; Cibuzar, Branelle R.; Milstead, Jeffery R.; Pietrzyk,, Robert A.; Clark, Mark S.F.

2009-01-01

A device capable of making in-flight volume measurements of single void urine samples, the Urine Monitoring System (UMS), was developed and flown on seven U.S. Space Shuttle missions. This device provided volume data for each urine void from multiple crewmembers and allowed samples of each to be taken and returned to Earth for post-flight analysis. There were a number of design flaws in the original instrument including the presence of liquid carry-over producing invalid "actual" micturition volumes and cross-contamination between successive users from residual urine in "dead" spots". Additionally, high or low volume voids could not be accurately measured, the on-orbit calibration and nominal use sequence was time intensive, and the unit had to be returned and disassembled to retrieve the volume data. These problems have been resolved in a new version, the International Space Station (ISS) UMS, that has been designed to provide real-time in-flight volume data with accuracy and precision equivalent to measurements made on Earth and the ability to provide urine samples that are unadulterated by the device. Originally conceived to be interfaced with a U.S.-built Waste Collection System (WCS), the unit now has been modified to interface with the Russian-supplied Sanitary Hygiene Device (ASY). The ISS UMS provides significant advantages over the current method of collecting urine samples into Urine Collection Devices (UCDs), from which samples are removed and returned to Earth for analyses. A significant future advantage of the UMS is that it can provide an interface to analytical instrumentation that will allow real-time measurement of urine bioanalytes allowing monitoring of crewmember health status during flight and the ability to provide medical interventions based on the results of these measurements. Currently, the ISS UMS is scheduled to launch along with Node-3 on STS-130 (20A) in December 2009. UMS will be installed and scientific/functional verification completed prior to placing the instrument into operation. Samples collected during the verification sequence will be returned for analyses on STS-131 (19A) currently scheduled for launch in March 2010. The presence of a UMS on ISS will provide the capability to conduct additional collaborative human life science investigations among the ISS International Partners.

Performance of juvenile steelhead trout (Oncorhynchus mykiss) produced from untreated and cryopreserved milt

USGS Publications Warehouse

Hayes, Michael C.; Rubin, Stephen P.; Hensleigh, Jay E.; Reisenbichler, Reginald R.; Wetzel, Lisa A.

2005-01-01

Despite the expanding use of milt cryopreservation in aquaculture, the performance of fish produced from this technique has not been fully explored beyond initial rearing stages. We compared the performance of juvenile steelhead Oncorhynchus mykiss produced from untreated (UM) and cryopreserved milt (CM) and reared for 4–9 months. For the 1996 brood, CM alevins were heavier (∼ 1.7%, P < 0.01) than UM alevins and length was influenced by a significant milt-by-family interaction (P < 0.03) suggesting a greater treatment effect for some families. No significant differences were found in length or weight (P > 0.05) for 1997 brood alevins and percent yolk was similar for both broods (P > 0.34). In growth and survival experiment I (GSE-I, 1996), UM and CM juveniles reared in separate tanks and fed to satiation (130 days) showed no significant differences in survival, length or weight (P > 0.05) between milt groups. In contrast, for UM and CM siblings reared in the same tank for 210 days on a low food ration (GSE-II), survival was similar (P > 0.05), but length (UM 4% > CM, P < 0.05) and possibly weight (UM 15% > CM, P = 0.08), were influenced by cryopreservation. Fish from the 1997 brood (GSE-III) were reared for 313 days in a repeat of GSE-II and no differences were found in survival (P = 0.47), length (P = 0.75) or weight (P = 0.76) suggesting considerable heterogeneity between broods. Performance of the 1996 brood was also tested for response to stress and a disease challenge. Cortisol responses of juveniles exposed to acute stress were not significantly different (P = 0.19), but mean cortisol was consistently and significantly greater (P < 0.01) for CM than UM fish exposed to a 48-h stress (increased density). After exposure to three dosages of the bacteria, Listonella anguillarum, we found similar mortality proportions (P = 0.72) for UM and CM fish. Variable juvenile performance for the parameters tested indicated significant differences among broods and families and suggests a cautionary approach to the widespread use of cryopreservation for steelhead.

A Comparative Study of Various Electric Propulsion Systems and their Impact on a Nominal Ship Design

DTIC Science & Technology

1987-06-01

Permanent Magnet Motors ," Advanced Mechanical Technology, Inc., 1983. 20. Marshall, McMurray, Richter, Webster, and...December 1977. 21. Triezenbarg, Greene, Hannan, and Dvorsky, "Study of Permanent Magnet Motors for Naval Propulsion," Westinghcuse Research Report 80=9B2...34 Paper 71 CP 155-PWR, IEEE Winter Power Meeting, New York, February 1971. 34. Ireland, James R., Ceramic Permanent - Magnet Motors , McGraw-Hill, New York, 1968. 206

Automotive Test Rig Final Design Report. Volume 2. Control System.

DTIC Science & Technology

1986-01-01

Pressure Switch Status P27 Low Brake Release Pressure Switch Status P26 Low Brake...Supply Pressure Switch Status P25 Low Port Charge Pump Pressure Switch Status P24 Low Starboard Charge Pump Pressure Switch Status P23 Hydraulic Filter By...Sensed Switch Status P31 Low Scavenge Pump Pressure Switch Status P30 P37 Signal Return for Computer J21 Not Used J22 P A +24 B Pwr Rtn C Ground C

Nuclear Fuel Depletion Analysis Using Matlab Software

NASA Astrophysics Data System (ADS)

Faghihi, F.; Nematollahi, M. R.

Coupled first order IVPs are frequently used in many parts of engineering and sciences. In this article, we presented a code including three computer programs which are joint with the Matlab software to solve and plot the solutions of the first order coupled stiff or non-stiff IVPs. Some engineering and scientific problems related to IVPs are given and fuel depletion (production of the 239Pu isotope) in a Pressurized Water Nuclear Reactor (PWR) are computed by the present code.

Limited Artificial and Natural Icing Tests Production UH-60A Helicopter (Re-Evaluation).

DTIC Science & Technology

1981-08-01

parameters , and definitions of icing types and severities are presented in appendix D. 2 RESULTS AND DISCUSSION GENERAL 9. Artificial and natural icing flight...anti-ice off, the system may be reactivated by cycling the appropriate windshield anti-ice switch. The windshield anti-ice system is fully operational...is off, then the fault monitor illuminates the respective PWR light on its front panel. The light informs the crew that further action is requied to

A NIST Kinetic Data Base for PAH Reaction and Soot Particle Inception During Combusion

DTIC Science & Technology

2007-12-01

in Computational Fluid Dynamics (CFD) codes hat have lead to the capability of describing complex reactive flow problems and thus simulating... parameters . However in the absence of data estimates must be made. Since the chemistry of combustion is extremely complex and for proper description...118:381-389 9. Babushok, V. and Tsang, W., J. Prop. and Pwr . 20 (2004) 403-414. 10. . Fournet, R., Warth, V., Glaude, P.A., Battin-Leclerc, F

Efficiency, equity and feasibility of strategies to identify the poor: an application to premium exemptions under National Health Insurance in Ghana.

PubMed

Jehu-Appiah, Caroline; Aryeetey, Genevieve; Spaan, Ernst; Agyepong, Irene; Baltussen, Rob

2010-05-01

This paper outlines the potential strategies to identify the poor, and assesses their feasibility, efficiency and equity. Analyses are illustrated for the case of premium exemptions under National Health Insurance (NHI) in Ghana. A literature search in Medline search was performed to identify strategies to identify the poor. Models were developed including information on demography and poverty, and costs and errors of in- and exclusion of these strategies in two regions in Ghana. Proxy means testing (PMT), participatory welfare ranking (PWR), and geographic targeting (GT) are potentially useful strategies to identify the poor, and vary in terms of their efficiency, equity and feasibility. Costs to exempt one poor individual range between US$11.63 and US$66.67, and strategies may exclude up to 25% of the poor. Feasibility of strategies is dependent on their aptness in rural/urban settings, and administrative capacity to implement. A decision framework summarizes the above information to guide policy making. We recommend PMT as an optimal strategy in relative low poverty incidence urbanized settings, PWR as an optimal strategy in relative low poverty incidence rural settings, and GT as an optimal strategy in high incidence poverty settings. This paper holds important lessons not only for NHI in Ghana but also for other countries implementing exemption policies. Copyright (c) 2009 Elsevier Ireland Ltd. All rights reserved.

Costs, equity, efficiency and feasibility of identifying the poor in Ghana's National Health Insurance Scheme: empirical analysis of various strategies.

PubMed

Aryeetey, Genevieve Cecilia; Jehu-Appiah, Caroline; Spaan, Ernst; Agyepong, Irene; Baltussen, Rob

2012-01-01

To analyse the costs and evaluate the equity, efficiency and feasibility of four strategies to identify poor households for premium exemptions in Ghana's National Health Insurance Scheme (NHIS): means testing (MT), proxy means testing (PMT), participatory wealth ranking (PWR) and geographic targeting (GT) in urban, rural and semi-urban settings in Ghana. We conducted the study in 145-147 households per setting with MT as our gold standard strategy. We estimated total costs that included costs of household surveys and cost of premiums paid to the poor, efficiency (cost per poor person identified), equity (number of true poor excluded) and the administrative feasibility of implementation. The cost of exempting one poor individual ranged from US$15.87 to US$95.44; exclusion of the poor ranged between 0% and 73%. MT was most efficient and equitable in rural and urban settings with low-poverty incidence; GT was efficient and equitable in the semi-urban setting with high-poverty incidence. PMT and PWR were less equitable and inefficient although feasible in some settings. We recommend MT as optimal strategy in low-poverty urban and rural settings and GT as optimal strategy in high-poverty semi-urban setting. The study is relevant to other social and developmental programmes that require identification and exemptions of the poor in low-income countries. © 2011 Blackwell Publishing Ltd.

Calculation and benchmarking of an azimuthal pressure vessel neutron fluence distribution using the BOXER code and scraping experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holzgrewe, F.; Hegedues, F.; Paratte, J.M.

1995-03-01

The light water reactor BOXER code was used to determine the fast azimuthal neutron fluence distribution at the inner surface of the reactor pressure vessel after the tenth cycle of a pressurized water reactor (PWR). Using a cross-section library in 45 groups, fixed-source calculations in transport theory and x-y geometry were carried out to determine the fast azimuthal neutron flux distribution at the inner surface of the pressure vessel for four different cycles. From these results, the fast azimuthal neutron fluence after the tenth cycle was estimated and compared with the results obtained from scraping test experiments. In these experiments,more » small samples of material were taken from the inner surface of the pressure vessel. The fast neutron fluence was then determined form the measured activity of the samples. Comparing the BOXER and scraping test results have maximal differences of 15%, which is very good, considering the factor of 10{sup 3} neutron attenuation between the reactor core and the pressure vessel. To compare the BOXER results with an independent code, the 21st cycle of the PWR was also calculated with the TWODANT two-dimensional transport code, using the same group structure and cross-section library. Deviations in the fast azimuthal flux distribution were found to be <3%, which verifies the accuracy of the BOXER results.« less

Korean standard nuclear plant ex-vessel neutron dosimetry program Ulchin 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duo, J.I.; Chen, J.; Kulesza, J.A.

2011-07-01

A comprehensive ex-vessel neutron dosimetry (EVND) surveillance program has been deployed in 16 pressurized water reactors (PWR) in South Korea and EVND dosimetry sets have already been installed and analyzed in Westinghouse reactor designs. In this paper, the unique features of the design, training, and installation in the Korean standard nuclear plant (KSNP) Ulchin Unit 4 are presented. Ulchin Unit 4 Cycle 9 represents the first dosimetry analyzed from the EVND design deployed in KSNP plants: Yonggwang Units 3 through 6 and Ulchin Units 3 through 6. KSNP's cavity configuration precludes a conventional installation from the cavity floor. The solution,more » requiring the installation crew to access the cavity at an elevation of the active core, places a premium on rapid installation due to high area dose rates. Numerous geometrical features warranted the use of a detailed design in true 3D mechanical design software to control interferences. A full-size training mockup maximized the crew ability to correctly install the instrument in minimum time. The analysis of the first dosimetry set shows good agreements between measurement and calculation within the associated uncertainties. A complete EVND system has been successfully designed, installed, and analyzed for a KNSP plant. Current and future EVND analyses will continue supporting the successful operation of PWR units in South Korea. (authors)« less

The role of Hydrogen and Creep in Intergranular Stress Corrosion Cracking of Alloy 600 and Alloy 690 in PWR Primary Water Environments ? a Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rebak, R B; Hua, F H

2004-07-12

Intergranular attack (IGA) and intergranular stress corrosion cracking (IGSCC) of Alloy 600 in PWR steam generator environment has been extensively studied for over 30 years without rendering a clear understanding of the essential mechanisms. The lack of understanding of the IGSCC mechanism is due to a complex interaction of numerous variables such as microstructure, thermomechanical processing, strain rate, water chemistry and electrochemical potential. Hydrogen plays an important role in all these variables. The complexity, however, significantly hinders a clearer and more fundamental understanding of the mechanism of hydrogen in enhancing intergranular cracking via whatever mechanism. In this work, an attemptmore » is made to review the role of hydrogen based on the current understanding of grain boundary structure and chemistry and intergranular fracture of nickel alloys, effect of hydrogen on electrochemical behavior of Alloy 600 and Alloy 690 (e.g. the passive film stability, polarization behavior and open-circuit potential) and effect of hydrogen on PWSCC behavior of Alloy 600 and Alloy 690. Mechanistic studies on the PWSCC are briefly reviewed. It is concluded that further studies on the role of hydrogen on intergranular cracking in both inert and primary side environments are needed. These studies should focus on the correlation of the results obtained at different laboratories by different methods on materials with different metallurgical and chemical parameters.« less

Finite Element Stress Analysis of Spent Nuclear Fuel Disposal Canister in a Deep Geological Repository

NASA Astrophysics Data System (ADS)

Kwon, Young Joo; Choi, Jong Won

This paper presents the finite element stress analysis of a spent nuclear fuel disposal canister to provide basic information for dimensioning the canister and configuration of canister components and consequently to suggest the structural analysis methodology for the disposal canister in a deep geological repository which is nowadays very important in the environmental waste treatment technology. Because of big differences in the pressurized water reactor (PWR) and the Canadian deuterium and uranium reactor (CANDU) fuel properties, two types of canisters are conceived. For manufacturing, operational reasons and standardization, however, both canisters have the same outer diameter and length. The construction type of canisters introduced here is a solid structure with a cast insert and a corrosion resistant overpack. The structural stress analysis is carried out using a finite element analysis code, NISA, and focused on the structural strength of the canister against the expected external pressures due to the swelling of the bentonite buffer and the hydrostatic head. The canister must withstand these large pressure loads. Consequently, canisters presented here contain 4 PWR fuel assemblies and 33×9 CANDU fuel bundles. The outside diameter of the canister for both fuels is 122cm and the cast insert diameter is 112cm. The total length of the canister is 483cm with the lid/bottom and the outer shell of 5cm.

Nuclear Data Uncertainties for Typical LWR Fuel Assemblies and a Simple Reactor Core

NASA Astrophysics Data System (ADS)

Rochman, D.; Leray, O.; Hursin, M.; Ferroukhi, H.; Vasiliev, A.; Aures, A.; Bostelmann, F.; Zwermann, W.; Cabellos, O.; Diez, C. J.; Dyrda, J.; Garcia-Herranz, N.; Castro, E.; van der Marck, S.; Sjöstrand, H.; Hernandez, A.; Fleming, M.; Sublet, J.-Ch.; Fiorito, L.

2017-01-01

The impact of the current nuclear data library covariances such as in ENDF/B-VII.1, JEFF-3.2, JENDL-4.0, SCALE and TENDL, for relevant current reactors is presented in this work. The uncertainties due to nuclear data are calculated for existing PWR and BWR fuel assemblies (with burn-up up to 40 GWd/tHM, followed by 10 years of cooling time) and for a simplified PWR full core model (without burn-up) for quantities such as k∞, macroscopic cross sections, pin power or isotope inventory. In this work, the method of propagation of uncertainties is based on random sampling of nuclear data, either from covariance files or directly from basic parameters. Additionally, possible biases on calculated quantities are investigated such as the self-shielding treatment. Different calculation schemes are used, based on CASMO, SCALE, DRAGON, MCNP or FISPACT-II, thus simulating real-life assignments for technical-support organizations. The outcome of such a study is a comparison of uncertainties with two consequences. One: although this study is not expected to lead to similar results between the involved calculation schemes, it provides an insight on what can happen when calculating uncertainties and allows to give some perspectives on the range of validity on these uncertainties. Two: it allows to dress a picture of the state of the knowledge as of today, using existing nuclear data library covariances and current methods.

Task related doses in Spanish pressurized water reactors over the period 1988-1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

O`Donnell, P.; Labarta, T.; Amor, I.

1995-03-01

In order to evaluate in depth the collective dose trend and its correlation with the effectiveness of the practical application of the ALARA principle in Spanish nuclear facilities, and base the different policy lines to promote this criteria, the CSN has fullfilled an analysis of the task related doses data over the period 1988-1992. Previously, the CSN had required to the utilities the compilation of their refuelling outage collective dose from 1988 according with a predeterminate number of tasks, in order to have available a representative and retrospective set of data in an homogeneous way and coherent with the internationalmore » data banks on occupational exposure in NPP, as the CEC and the NEA ones. The scope of this analysis was the following: first, the collective dose summaries for outage tasks and departments for PWR and for BWR, including the minimum, maximum and average dose (and statistics data) for 18 different refuelling outage tasks and 12 personal departments for each generation of each type of rector, the task and department related collective dose trends in each plant and in each generation, and second, the dose reduction techniques having been used during that period in each plant and the relative level of adoption. In this presentation the main results and conclusions of the first part of the study are reviewed for PWR.« less

Measurement and Analysis of Structural Integrity of Reactor Core Support Structure in Pressurized Water Reactor (PWR) Plant

NASA Astrophysics Data System (ADS)

Ansari, Saleem A.; Haroon, Muhammad; Rashid, Atif; Kazmi, Zafar

2017-02-01

Extensive calculation and measurements of flow-induced vibrations (FIV) of reactor internals were made in a PWR plant to assess the structural integrity of reactor core support structure against coolant flow. The work was done to meet the requirements of the Fukushima Response Action Plan (FRAP) for enhancement of reactor safety, and the regulatory guide RG-1.20. For the core surveillance measurements the Reactor Internals Vibration Monitoring System (IVMS) has been developed based on detailed neutron noise analysis of the flux signals from the four ex-core neutron detectors. The natural frequencies, displacement and mode shapes of the reactor core barrel (CB) motion were determined with the help of IVMS. The random pressure fluctuations in reactor coolant flow due to turbulence force have been identified as the predominant cause of beam-mode deflection of CB. The dynamic FIV calculations were also made to supplement the core surveillance measurements. The calculational package employed the computational fluid dynamics, mode shape analysis, calculation of power spectral densities of flow & pressure fields and the structural response to random flow excitation forces. The dynamic loads and stiffness of the Hold-Down Spring that keeps the core structure in position against upward coolant thrust were also determined by noise measurements. Also, the boron concentration in primary coolant at any time of the core cycle has been determined with the IVMS.

Evaluation of on-line chelant addition to PWR steam generators. Steam generator cleaning project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tvedt, T.J.; Wallace, S.L.; Griffin, F. Jr.

1983-09-01

The investigation of chelating agents for continuous water treatment of secondary loops of PWR steam generators were conducted in two general areas: the study of the chemistry of chelating agents and the study of materials compatability with chelating agents. The thermostability of both EDTA and HEDTA metal chelates in All Volatile Treatment (AVT) water chemistry were shown to be greater than or equal to the thermostability of EDTA metal chelates in phosphate-sulfite water chemistry. HEDTA metal chelates were shown to have a much greater stability than EDTA metal chelates. Using samples taken from the EDTA metal chelate thermostability study andmore » from the Commonwealth Research Corporation (CRC) model steam generators (MSG), EDTA decomposition products were determined. Active metal surfaces were shown to become passivated when exposed to EDTA and HEDTA concentrations as high as 0.1% w/w in AVT. Trace amounts of iron in the water were found to increase the rate of passivation. Material balance and visual inspection data from CRC model steam generators showed that metal was transported through and cleaned from the MSG's. The Inconel 600 tubes of the salt water fouled model steam generators experienced pitting corrosion. Results of this study demonstrates the feasibility of EDTA as an on-line water treatment additive to maintain nuclear steam generators in a clean condition.« less

System-Level Heat Transfer Analysis, Thermal- Mechanical Cyclic Stress Analysis, and Environmental Fatigue Modeling of a Two-Loop Pressurized Water Reactor. A Preliminary Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohanty, Subhasish; Soppet, William; Majumdar, Saurin

This report provides an update on an assessment of environmentally assisted fatigue for light water reactor components under extended service conditions. This report is a deliverable in April 2015 under the work package for environmentally assisted fatigue under DOE's Light Water Reactor Sustainability program. In this report, updates are discussed related to a system level preliminary finite element model of a two-loop pressurized water reactor (PWR). Based on this model, system-level heat transfer analysis and subsequent thermal-mechanical stress analysis were performed for typical design-basis thermal-mechanical fatigue cycles. The in-air fatigue lives of components, such as the hot and cold legs,more » were estimated on the basis of stress analysis results, ASME in-air fatigue life estimation criteria, and fatigue design curves. Furthermore, environmental correction factors and associated PWR environment fatigue lives for the hot and cold legs were estimated by using estimated stress and strain histories and the approach described in NUREG-6909. The discussed models and results are very preliminary. Further advancement of the discussed model is required for more accurate life prediction of reactor components. This report only presents the work related to finite element modelling activities. However, in between multiple tensile and fatigue tests were conducted. The related experimental results will be presented in the year-end report.« less

Impact of Reprocessed Uranium Management on the Homogeneous Recycling of Transuranics in PWRs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Youinou, Gilles J.

This article presents the results of a neutronics analysis related to the homogeneous recycling of transuranics (TRU) in PWRs with a MOX fuel using enriched uranium instead of depleted uranium. It also addresses an often, if not always, overlooked aspect related to the recycling of TRU in PWRs, namely the use of reprocessed uranium. From a neutronics point of view, it is possible to multi-recycle the entirety of the plutonium with or without neptunium and americium in a PWR fleet using MOX-EU fuel in between one third and two thirds of the fleet. Recycling neptunium and americium with plutonium significantlymore » decreases the decay heat of the waste stream between 100 to 1,000 years compared to those of an open fuel cycle or when only plutonium is recycled. The uranium present in MOX-EU used fuel still contains a significant amount of 235uranium and recycling it makes a major difference on the natural uranium needs. For example, a PWR fleet recycling its plutonium, neptunium and americium in MOXEU needs 28 percent more natural uranium than a reference UO 2 open cycle fleet generating the same energy if the reprocessed uranium is not recycled and 19 percent less if the reprocessed uranium is recycled back in the reactors, i.e. a 47 percent difference.« less

Impact of Reprocessed Uranium Management on the Homogeneous Recycling of Transuranics in PWRs

DOE PAGES

Youinou, Gilles J.

2017-05-04

This article presents the results of a neutronics analysis related to the homogeneous recycling of transuranics (TRU) in PWRs with a MOX fuel using enriched uranium instead of depleted uranium. It also addresses an often, if not always, overlooked aspect related to the recycling of TRU in PWRs, namely the use of reprocessed uranium. From a neutronics point of view, it is possible to multi-recycle the entirety of the plutonium with or without neptunium and americium in a PWR fleet using MOX-EU fuel in between one third and two thirds of the fleet. Recycling neptunium and americium with plutonium significantlymore » decreases the decay heat of the waste stream between 100 to 1,000 years compared to those of an open fuel cycle or when only plutonium is recycled. The uranium present in MOX-EU used fuel still contains a significant amount of 235uranium and recycling it makes a major difference on the natural uranium needs. For example, a PWR fleet recycling its plutonium, neptunium and americium in MOXEU needs 28 percent more natural uranium than a reference UO 2 open cycle fleet generating the same energy if the reprocessed uranium is not recycled and 19 percent less if the reprocessed uranium is recycled back in the reactors, i.e. a 47 percent difference.« less

PRELIMINARY COUPLING OF THE MONTE CARLO CODE OPENMC AND THE MULTIPHYSICS OBJECT-ORIENTED SIMULATION ENVIRONMENT (MOOSE) FOR ANALYZING DOPPLER FEEDBACK IN MONTE CARLO SIMULATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matthew Ellis; Derek Gaston; Benoit Forget

In recent years the use of Monte Carlo methods for modeling reactors has become feasible due to the increasing availability of massively parallel computer systems. One of the primary challenges yet to be fully resolved, however, is the efficient and accurate inclusion of multiphysics feedback in Monte Carlo simulations. The research in this paper presents a preliminary coupling of the open source Monte Carlo code OpenMC with the open source Multiphysics Object-Oriented Simulation Environment (MOOSE). The coupling of OpenMC and MOOSE will be used to investigate efficient and accurate numerical methods needed to include multiphysics feedback in Monte Carlo codes.more » An investigation into the sensitivity of Doppler feedback to fuel temperature approximations using a two dimensional 17x17 PWR fuel assembly is presented in this paper. The results show a functioning multiphysics coupling between OpenMC and MOOSE. The coupling utilizes Functional Expansion Tallies to accurately and efficiently transfer pin power distributions tallied in OpenMC to unstructured finite element meshes used in MOOSE. The two dimensional PWR fuel assembly case also demonstrates that for a simplified model the pin-by-pin doppler feedback can be adequately replicated by scaling a representative pin based on pin relative powers.« less

Raízes pós-mitológicas da Astronomia Clássica

NASA Astrophysics Data System (ADS)

di Bartolo, L.; Villas da Rocha, J. F.

2004-02-01

Apresentamos como a invenção de um modelo astronômico e cosmológico fundado em causas naturais foi um processo gestado num ambiente cultural específico, o do advento do pensamento pós-mitológico, que tem como sua raiz mais funda a trajetória particular da Grécia Antiga, com ênfase na resolução de uma grave crise social e a evolução do mundo clássico para o contexto espiritual de um império universal.

Dehydration and clearing of adult Drosophila for ultramicroscopy.

PubMed

Becker, Klaus; Jährling, Nina; Saghafi, Saiedeh; Dodt, Hans-Ulrich

2013-07-01

This protocol describes the preparation of adult flies for ultramicroscopy (UM), a powerful imaging technique that achieves precise and accurate three-dimensional (3D) reconstructions of intact macroscopic specimens with micrometer resolution. In UM, a specimen in the size range of ∼1-15 mm is illuminated perpendicular to the observation pathway by two thin counterpropagating sheets of laser light. Thus, specimens for UM need to be sufficiently transparent, which requires chemical clearing in most cases. In this protocol, Drosophila melanogaster adults are fixed, dehydrated in ethanol, and then cleared in a solution of benzyl alcohol and benzyl benzoate.

VizieR Online Data Catalog: GJ 1214b optical and near-IR transit phot. (Angerhausen+, 2017)

NASA Astrophysics Data System (ADS)

Angerhausen, D.; Dreyer, C.; Placek, B.; Csizmadia, Sz.; Eigmueller, P.; Godolt, M.; Kitzmann, D.; Mallonn, M.; Becklin, E.; Collins, P.; Dunham, E. W.; Grenfell, J. L.; Hamilton, R. T.; Kabath, P.; Logsdon, S. E.; Mandell, A.; Mandushev, G.; McElwain, M.; McLean, I. S.; Pfueller, E.; Rauer, H.; Savage, M.; Shenoy, S.; Vacca, W. D.; van Cleve, J. E.; Wiedemann, M.; Wolf, J.

2017-11-01

The joint US-German Cycle 2 Guest Investigator (GI) programme - US-proposal: Angerhausen (2013); Germanproposal: Dreyer (2013) - was performed on SOFIAs flight number 149 on UT February 27, 2014. Observations were simultaneously conducted in two optical HIPO channels: open blue at 0.3-0.6um and Sloan z' at 0.9-m; and one infrared FLITECAM fiter: Paschen-α cont. at 1.9um. Complementary data were also obtained with the optical focal plane guiding camera FPI+ in the Sloan i' band (0.8um). (5 data files).

Landsat 7 - First Cloud-free Image of Yellowstone National Park

NASA Technical Reports Server (NTRS)

2002-01-01

This image of Yellowstone Lake, in the center of Yellowstone National Park, was taken by Landsat 7 on July 13, 1999. Bands 5 (1.65um),4 (.825um), and 2 (.565um) were used for red, green, and blue, respectively. Water appears blue/black, snow light blue, mature forest red/green, young forest pink, and grass and fields appear light green. Southwest of the lake is young forest that is growing in the wake of the widespread fires of 1988. For more information, see: Landsat 7 Fact Sheet Landsat 7 in Mission Control Image by Rich Irish, NASA GSFC

VizieR Online Data Catalog: ISOCAM survey of Serpens/G3-G6 (Djupvik+, 2006)

NASA Astrophysics Data System (ADS)

Djupvik, A. A.; Andre, P.; Bontemps, S.; Motte, F.; Olofsson, G.; Gaalfalk, M.; Floren, H.-G.

2006-08-01

We present results from an ISOCAM survey in the two broadband filters LW2 (5-8.5um) and LW3 (12-18um) of a 19'x16' field called Serp_NH3 centred on the optical group Serpens/G3-G6. A total of 186 sources were detected in the 6.7um band and/or the 14.3um band to a limiting sensitivity of ~2mJy. These have been cross-correlated with the 2MASS catalogue and are all listed in table1. Deep follow-up photometry in the Ks band obtained with Arnica at the Nordic Optical Telescope (NOT) is listed in table2. Deep L' band photometry of selected sources using SIRCA at the NOT is listed in table3. Continuum emission at 1.3mm and 3.6cm was observed with IRAM and VLA, respectively, and deep imaging in the 2.12um S(1) line of H2 was obtained with NOTCam at the NOT. We find strong evidence for a stellar population of 31 Class II sources (listed in table5), 5 flat-spectrum sources, 5 Class I sources (listed in table4), and two Class 0 sources. Our method does not sample the Class III sources. (3 data files).

Ultramicroscopy as a novel tool to unravel the tropism of AAV gene therapy vectors in the brain.

PubMed

Alves, Sandro; Bode, Julia; Bemelmans, Alexis-Pierre; von Kalle, Christof; Cartier, Nathalie; Tews, Björn

2016-06-20

Recombinant adeno-associated viral (AAV) vectors have advanced to the vanguard of gene therapy. Numerous naturally occurring serotypes have been used to target cells in various tissues. There is a strong need for fast and dynamic methods which efficiently unravel viral tropism in whole organs. Ultramicroscopy (UM) is a novel fluorescence microscopy technique that images optically cleared undissected specimens, achieving good resolutions at high penetration depths while being non-destructive. UM was applied to obtain high-resolution 3D analysis of AAV transduction in adult mouse brains, especially in the hippocampus, a region of interest for Alzheimer's disease therapy. We separately or simultaneously compared transduction efficacies for commonly used serotypes (AAV9 and AAVrh10) using fluorescent reporter expression. We provide a detailed comparative and quantitative analysis of the transduction profiles. UM allowed a rapid analysis of marker fluorescence expression in neurons with intact projections deep inside the brain, in defined anatomical structures. Major hippocampal neuronal transduction was observed with both vectors, with slightly better efficacy for AAV9 in UM. Glial response and synaptic marker expression did not change post transduction.We propose UM as a novel valuable complementary tool to efficiently and simultaneously unravel tropism of different viruses in a single non-dissected adult rodent brain.

Kinome-wide transcriptional profiling of uveal melanoma reveals new vulnerabilities to targeted therapeutics.

PubMed

Bailey, Fiona P; Clarke, Kim; Kalirai, Helen; Kenyani, Jenna; Shahidipour, Haleh; Falciani, Francesco; Coulson, Judy M; Sacco, Joseph J; Coupland, Sarah E; Eyers, Patrick A

2018-03-01

Metastatic uveal melanoma (UM) is invariably fatal, usually within a year of diagnosis. There are currently no effective therapies, and clinical studies employing kinase inhibitors have so far demonstrated limited success. This is despite common activating mutations in GNAQ/11 genes, which trigger signalling pathways that might predispose tumours to a variety of targeted drugs. In this study, we have profiled kinome expression network dynamics in various human ocular melanomas. We uncovered a shared transcriptional profile in human primary UM samples and across a variety of experimental cell-based models. The poor overall response of UM cells to FDA-approved kinase inhibitors contrasted with much higher sensitivity to the bromodomain inhibitor JQ1, a broad transcriptional repressor. Mechanistically, we identified a repressed FOXM1-dependent kinase subnetwork in JQ1-exposed cells that contained multiple cell cycle-regulated protein kinases. Consistently, we demonstrated vulnerability of UM cells to inhibitors of mitotic protein kinases within this network, including the investigational PLK1 inhibitor BI6727. We conclude that analysis of kinome-wide signalling network dynamics has the potential to reveal actionable drug targets and inhibitors of potential therapeutic benefit for UM patients. © 2017 The Authors. Pigment Cell & Melanoma Research Published by John Wiley & Sons.

VizieR Online Data Catalog: Water masers in M31. I. Recombination lines (Darling+, 2016)

NASA Astrophysics Data System (ADS)

Darling, J.; Gerard, B.; Amiri, N.; Lawrence, K.

2016-09-01

We constructed a catalog of 506 unresolved 24um sources from the Spitzer 24um map of M31 (Gordon et al. 2006ApJ...638L..87G); see Figure 1. Darling (2011ApJ...732L...2D) observed 206 24um sources in M31 using the Green Bank Telescope (GBT) in 2010 October through December. The 616-523 22.23508GHz ortho-water maser line observations were reported in Darling (2011ApJ...732L...2D), but simultaneous observations of the para-ammonia (NH3) rotational ground-state inversion transitions in the metastable states (J,K)=(1,1) and (2,2) at 23.6945 and 23.72263GHz, respectively, and the hydrogen recombination line H66α at 22.36417GHz were not. We subsequently observed all four of these lines toward an additional 300 24um sources in 2011 October through 2012 January. The resolution of the 24um Spitzer image is 6" (Gordon et al. 2006ApJ...638L..87G), so the unresolved IR sources remained within the 33" GBT beam even during the largest pointing drifts. The 33" beam (FWHM) at 22GHz spans 125pc in M31. (1 data file).

The Athenæum Club, the Royal Society and the reform of dentistry in nineteenth-century Britain: A research report

PubMed Central

Bishop, Malcolm G. H.

2017-01-01

In 1978 M. J. Peterson examined the role played by the Royal College of Surgeons (RCS) in nineteenth-century dental reform, noting the establishment of its Licence in Dental Surgery (LDS) in 1859. In a paper published in Notes and Records in 2010, the present author described the influential role played by Fellows of the Royal Society during the nineteenth-century campaign for dental reform led by Sir John Tomes. Key players in this campaign, including the dentists Samuel Cartwright, Thomas Bell and James Salter, were, as well as being Fellows of the Royal Society, members of the Athenæum Club. The present research report indicates the roles played by those members of the Athenæum Club who were also Fellows of the Royal Society in the scientific and professional reform of nineteenth-century dentistry. Although it does not attempt to document meetings at the Club, it suggests the potential for a symbiotic effect between the Royal Society and the Athenæum. Where the previous paper proposed an active scientific role for the Royal Society in reforming dentistry, this paper presents the Athenæum as a significant extension of the sphere of influence into the cultural realm for those who did enjoy membership of both organizations.

543 N McClurg, October 2010, Lindsay Light Radiological Survey

EPA Pesticide Factsheets

The field gamma measurements within the excavation andthe spoil materials generated during the excavation process did not exceed the respective thresholdvalues previously stated and ranged from a minim um of 1,020 cpm to a maxim um of 7,150 cpm.

Constraints on silicates formation in the Si-Al-Fe system: Application to hard deposits in steam generators of PWR nuclear reactors

NASA Astrophysics Data System (ADS)

Berger, Gilles; Million-Picallion, Lisa; Lefevre, Grégory; Delaunay, Sophie

2015-04-01

Introduction: The hydrothermal crystallization of silicates phases in the Si-Al-Fe system may lead to industrial constraints that can be encountered in the nuclear industry in at least two contexts: the geological repository for nuclear wastes and the formation of hard sludges in the steam generator of the PWR nuclear plants. In the first situation, the chemical reactions between the Fe-canister and the surrounding clays have been extensively studied in laboratory [1-7] and pilot experiments [8]. These studies demonstrated that the high reactivity of metallic iron leads to the formation of Fe-silicates, berthierine like, in a wide range of temperature. By contrast, the formation of deposits in the steam generators of PWR plants, called hard sludges, is a newer and less studied issue which can affect the reactor performance. Experiments: We present here a preliminary set of experiments reproducing the formation of hard sludges under conditions representative of the steam generator of PWR power plant: 275°C, diluted solutions maintained at low potential by hydrazine addition and at alkaline pH by low concentrations of amines and ammoniac. Magnetite, a corrosion by-product of the secondary circuit, is the source of iron while aqueous Si and Al, the major impurities in this system, are supplied either as trace elements in the circulating solution or by addition of amorphous silica and alumina when considering confined zones. The fluid chemistry is monitored by sampling aliquots of the solution. Eh and pH are continuously measured by hydrothermal Cormet© electrodes implanted in a titanium hydrothermal reactor. The transformation, or not, of the solid fraction was examined post-mortem. These experiments evidenced the role of Al colloids as precursor of cements composed of kaolinite and boehmite, and the passivation of amorphous silica (becoming unreactive) likely by sorption of aqueous iron. But no Fe-bearing was formed by contrast to many published studies on the Fe-clay interactions in the nuclear waste storage, and by contrast with basic thermodynamic predictions. Conclusion: The Fe-clays and steam generators contexts imply relatively close aqueous environments: hydrothermal, reduced, diluted, neutral to slightly alkaline. The main difference is the status of iron: ferric/ferrous (magnetite) in the steam generators, metallic in the Fe-clay experiments. The concentration of aqueous iron when supplied by magnetite is low and does not allow its incorporation in secondary phases. By contrast, aqueous ferrous iron released by the corrosion of steel is not limited by the source, rather by the sink, and produces Fe-rich silicates. This example illustrates the discrepancy between complex mineral reactions and oversimplified predictions when sorption/passivation and nucleation/growth constraints are ignored. Reference: [1] Lanson et al. (2012) Amer. Min. 97, 864-871. [2] Lantenois et al. (2005) Clays & Clay Min. 53, 597-612. [3] Mosser-Ruck et al. (2010) Clays & Clay Min. 58, 280-291. [4] Perronnet et al. (2008) App. Clay Sci. 38, 187-202. [5] Osacky et al. (2010) App. Clay Sci. 50, 237-244. [6] Guillaume et al. (2003) Clay Min. 38, 281-302. [7] Rivard et al. (2013) Amer. Mineral. 98, 163-180. [8] Svensson and Hansen (2013) Clays & Clay Min. 61, 566-579.

Development of burnup dependent fuel rod model in COBRA-TF

NASA Astrophysics Data System (ADS)

Yilmaz, Mine Ozdemir

The purpose of this research was to develop a burnup dependent fuel thermal conductivity model within Pennsylvania State University, Reactor Dynamics and Fuel Management Group (RDFMG) version of the subchannel thermal-hydraulics code COBRA-TF (CTF). The model takes into account first, the degradation of fuel thermal conductivity with high burnup; and second, the fuel thermal conductivity dependence on the Gadolinium content for both UO2 and MOX fuel rods. The modified Nuclear Fuel Industries (NFI) model for UO2 fuel rods and Duriez/Modified NFI Model for MOX fuel rods were incorporated into CTF and fuel centerline predictions were compared against Halden experimental test data and FRAPCON-3.4 predictions to validate the burnup dependent fuel thermal conductivity model in CTF. Experimental test cases from Halden reactor fuel rods for UO2 fuel rods at Beginning of Life (BOL), through lifetime without Gd2O3 and through lifetime with Gd 2O3 and a MOX fuel rod were simulated with CTF. Since test fuel rod and FRAPCON-3.4 results were based on single rod measurements, CTF was run for a single fuel rod surrounded with a single channel configuration. Input decks for CTF were developed for one fuel rod located at the center of a subchannel (rod-centered subchannel approach). Fuel centerline temperatures predicted by CTF were compared against the measurements from Halden experimental test data and the predictions from FRAPCON-3.4. After implementing the new fuel thermal conductivity model in CTF and validating the model with experimental data, CTF model was applied to steady state and transient calculations. 4x4 PWR fuel bundle configuration from Purdue MOX benchmark was used to apply the new model for steady state and transient calculations. First, one of each high burnup UO2 and MOX fuel rods from 4x4 matrix were selected to carry out single fuel rod calculations and fuel centerline temperatures predicted by CTF/TORT-TD were compared against CTF /TORT-TD /FRAPTRAN predictions. After confirming that the new fuel thermal conductivity model in CTF worked and provided consistent results with FRAPTRAN predictions for a single fuel rod configuration, the same type of analysis was carried out for a bigger system which is the 4x4 PWR bundle consisting of 15 fuel pins and one control guide tube. Steady- state calculations at Hot Full Power (HFP) conditions for control guide tube out (unrodded) were performed using the 4x4 PWR array with CTF/TORT-TD coupled code system. Fuel centerline, surface and average temperatures predicted by CTF/TORT-TD with and without the new fuel thermal conductivity model were compared against CTF/TORT-TD/FRAPTRAN predictions to demonstrate the improvement in fuel centerline predictions when new model was used. In addition to that constant and CTF dynamic gap conductance model were used with the new thermal conductivity model to show the performance of the CTF dynamic gap conductance model and its impact on fuel centerline and surface temperatures. Finally, a Rod Ejection Accident (REA) scenario using the same 4x4 PWR array was run both at Hot Zero Power (HZP) and Hot Full Power (HFP) condition, starting at a position where half of the control rod is inserted. This scenario was run using CTF/TORT-TD coupled code system with and without the new fuel thermal conductivity model. The purpose of this transient analysis was to show the impact of thermal conductivity degradation (TCD) on feedback effects, specifically Doppler Reactivity Coefficient (DRC) and, eventually, total core reactivity.

VizieR Online Data Catalog: FourStar galaxy evolution survey (ZFOURGE) (Straatman+, 2016)

NASA Astrophysics Data System (ADS)

Straatman, C. M. S.; Spitler, L. R.; Quadri, R. F.; Labbe, I.; Glazebrook, K.; Persson, S. E.; Papovich, C.; Tran, K.-V.; Brammer, G. B.; Cowley, M.; Tomczak, A.; Nanayakkara, T.; Alcorn, L.; Allen, R.; Broussard, A.; van Dokkum, P.; Forrest, B.; van Houdt, J.; Kacprzak, G. G.; Kawinwanichakij, L.; Kelson, D. D.; Lee, J.; McCarthy, P. J.; Mehrtens, N.; Monson, A.; Murphy, D.; Rees, G.; Tilvi, V.; Whitaker, K. E.

2017-03-01

We present the FourStar galaxy evolution survey (ZFOURGE) photometric catalogs comprising >70000 galaxies, selected from ultradeep Ks-band detection images (25.5-26.5 AB mag, 5σ, total). We use 5 near-IR medium-bandwidth filters (J1, J2, J3, Hs, Hl) as well as broad-band Ks at 1.05-2.16 micron to 25-26 AB at a seeing of ~0.5 arcsec. Each field has ancillary imaging in 26-40 filters at 0.3-8 micron. We derive photometric redshifts, rest-frame U-V and V-J colors, and stellar population properties from SED fitting. The photometric redshifts have uncertainty σz=0.010, 0.009, and 0.011 in CDFS, COSMOS and UDS, respectively, if compared with spectroscopic redshifts. A pair test indicates σz,pairs=0.01-0.02 at 1

Parylene supported 20um*20um uncooled thermoelectric infrared detector with high fill factor

NASA Astrophysics Data System (ADS)

Modarres-Zadeh, Mohammad J.; Carpenter, Zachary S.; Rockley, Mark G.; Abdolvand, Reza

2012-06-01

Presented is a novel design for an uncooled surface-micromachined thermoelectric (TE) infrared (IR) detector. The detector features a P-doped polysilicon/Nichrome (Cr20-Ni80) thermocouple, which is embedded into a thin layer of Parylene-N to provide structural support. The low thermal conductivity (~0.1W/m.K), chemical resistance, and ease of deposition/patterning of Parylene-N make it an excellent choice of material for use in MEMS thermal detectors. This detector also features an umbrella-like IR absorber composed of a three layer stack of NiCr/SiN/NiCr to optimize IR absorption. The total device area is 20 um * 20 um per pixel with an absorber area of ~19 um * 19 um resulting in a fill factor of 90%. At room temperature, a DC responsivity of ~170V/W with a rise time of less than 8 ms is measured from the fabricated devices in vacuum when viewing a 500K blackbody without any concentrating optics. The dominant source of noise in thermoelectric IR detectors is typically Johnson noise when the detectors are operating in an open circuit condition. The fabricated detectors have resistances about 85KOhm which results in Johnson noise of about 38nV/Hz^0.5. The D* is calculated to be 9 * 106 cm*Hz0.5/ W. Preliminary finite element analysis indicates that the thermal conduction from the hot junction to the substrate through the TE wires is dominant ( GTE >> Gparylene) considering the fabricated dimensions of the parylene film and the TE wires. Thus, by further reducing the size of the TE wires, GTE can be decreased and hence, responsivity can be improved while the parylene film sustains the structural integrity of the cell.

Activation of the Constitutive Androstane Receptor Inhibits Gluconeogenesis without Affecting Lipogenesis or Fatty Acid Synthesis in Human Hepatocytes

PubMed Central

Lynch, Caitlin; Pan, Yongmei; Li, Linhao; Heyward, Scott; Moeller, Timothy; Swaan, Peter W.; Wang, Hongbing

2014-01-01

Objective Accumulating evidence suggests that activation of mouse constitutive androstane receptor (mCAR) alleviates type 2 diabetes and obesity by inhibiting hepatic gluconeogenesis, lipogenesis, and fatty acid synthesis. However, the role of human (h) CAR in energy metabolism is largely unknown. The present study aims to investigate the effects of selective hCAR activators on hepatic energy metabolism in human primary hepatocytes (HPH). Methods Ligand-based structure-activity models were used for virtual screening of the Specs database (www.specs.net) followed by biological validation in cell-based luciferase assays. The effects of two novel hCAR activators (UM104 and UM145) on hepatic energy metabolism were evaluated in HPH. Results Real-time PCR and Western blotting analyses reveal that activation of hCAR by UM104 and UM145 significantly repressed the expression of glucose-6-phosphatase and phosphoenolpyruvate carboxykinase, two pivotal gluconeogenic enzymes, while exerting negligible effects on the expression of genes associated with lipogenesis and fatty acid synthesis. Functional experiments show that UM104 and UM145 markedly inhibit hepatic synthesis of glucose but not triglycerides in HPH. In contrast, activation of mCAR by 1,4-bis[2-(3,5-dichloropyridyloxy)]benzene, a selective mCAR activator, repressed the expression of genes associated with gluconeogenesis, lipogenesis, and fatty acid synthesis in mouse primary hepatocytes, which were consistent with previous observations in mouse model in vivo. Conclusion Our findings uncover an important species difference between hCAR and mCAR in hepatic energy metabolism, where hCAR selectively inhibits gluconeogenesis without suppressing fatty acid synthesis. Implications Such species selectivity should be considered when exploring CAR as a potential therapeutic target for metabolic disorders. PMID:24878338

Microwave-Assisted Extraction, Chemical Structures, and Chain Conformation of Polysaccharides from a Novel Cordyceps Sinensis Fungus UM01.

PubMed

Cheong, Kit-Leong; Wang, Lan-Ying; Wu, Ding-Tao; Hu, De-Jun; Zhao, Jing; Li, Shao-Ping

2016-09-01

Cordyceps sinensis is a well-known tonic food with broad medicinal properties. The aim of the present study was to investigate the optimization of microwave-assisted extraction (MAE) and characterize chemical structures and chain conformation of polysaccharides from a novel C. sinensis fungus UM01. Ion-exchange and gel filtration chromatography were used to purify the polysaccharides. The chemical structure of purified polysaccharide was determined through gas chromatography-mass spectrometry. Moreover, high performance size exclusion chromatography combined with refractive index detector and multiangle laser light scattering were conducted to analyze the molecular weight (Mw ) and chain conformation of purified polysaccharide. Based on the orthogonal design L9 , optimal MAE conditions could be obtained through 1300 W of microwave power, with a 5-min irradiation time at a solid to water ratio of 1:60, generating the highest extraction yield of 6.20%. Subsequently, the polysaccharide UM01-S1 was purified. The UM01-S1 is a glucan-type polysaccharide with a (1→4)-β-d-glucosyl backbone and branching points located at O-3 of Glcp with a terminal-d-Glcp. The Mw , radius of gyration (Rg ) and hydrodynamic radius (Rh ) of UM01-S1 were determined as 5.442 × 10(6)  Da, 21.8 and 20.2 nm, respectively. Using the polymer solution theory, the exponent (ν) value of the power law function was calculated as 0.38, and the shape factor (ρ = Rg /Rh ) was 1.079, indicating that UM01-S1 has a sphere-like conformation with a branched structure in an aqueous solution. These results provide fundamental information for the future application of polysaccharides from cultured C. sinensis in health and functional food area. © 2016 Institute of Food Technologists®

Chromosomal rearrangements in uveal melanoma: Chromothripsis.

PubMed

van Poppelen, Natasha M; Yavuzyigitoglu, Serdar; Smit, Kyra N; Vaarwater, Jolanda; Eussen, Bert; Brands, Tom; Paridaens, Dion; Kiliç, Emine; de Klein, Annelies

2018-05-04

Uveal melanoma (UM) is the most common primary intraocular malignancy in the Western world. Recurrent mutations in GNAQ, GNA11, CYSLTR2, PLCB4, BAP1, EIF1AX and SF3B1 are described as well as non-random chromosomal aberrations. Chromothripsis is a rare event in which chromosomes are shattered and rearranged and has been reported in a variety of cancers including UM. SNP arrays of 249 UM from patients who underwent enucleation, biopsy or endoresection were reviewed for the presence of chromothripsis. Chromothripsis was defined as ten or more breakpoints per chromosome involved. Genetic analysis of GNAQ, GNA11, BAP1, SF3B1 and EIF1AX was conducted using Sanger and next-generation sequencing. In addition, immunohistochemistry for BAP1 was performed. Chromothripsis was detected in seven out of 249 tumors and the affected chromosomes were chromosomes 3, 5, 6, 8, 12 and 13. The mean total of fragments per chromosome was 39.8 (range 12 - 116). In one UM, chromothripsis was present in two different chromosomes. GNAQ, GNA11 or CYSLTR2 mutations were present in six of these tumors and five tumors harbored a BAP1 mutation and/or lacked BAP1 protein expression by immunohistochemistry. Four of these tumors metastasized and for the fifth only short follow-up data are available. One of these metastatic tumors tumor harbored an SF3B1 mutation. No EIF1AX mutations were detected in any of the tumors. To conclude, chromothripsis is a rare event in UM, occurring in 2.8% of samples and without significant association with mutations in any of the common UM driver genes. This article is protected by copyright. All rights reserved. © 2018 Wiley Periodicals, Inc.

Ultramicronized palmitoylethanolamide (PEA-um(®)) in the treatment of idiopathic pulmonary fibrosis.

PubMed

Di Paola, Rosanna; Impellizzeri, Daniela; Fusco, Roberta; Cordaro, Marika; Siracusa, Rosalba; Crupi, Rosalia; Esposito, Emanuela; Cuzzocrea, Salvatore

2016-09-01

Pulmonary fibrosis is a chronic condition characterized by progressive scarring of lung parenchyma. The aim of this study was to examine the effects of an ultramicronized preparation of palmitoylethanolamide (PEA-um(®)), an endogenous fatty acid amide, in mice subjected to idiopathic pulmonary fibrosis. Idiopathic pulmonary fibrosis was induced in male mice by a single intratracheal administration of saline with bleomycin sulphate (1mg/kg body weight) in a volume of 100μL. PEA-um(®) was injected intraperitoneally at 1, 3 or 10mg/kg 1h after bleomycin instillation and daily thereafter. Animals were sacrificed after 7 and 21days by pentobarbitone overdose. One cohort of mice was sacrificed after seven days of bleomycin administration, followed by bronchoalveloar lavage and determination of myeloperoxidase activity, lung edema and histopathology features. In the 21-day cohort, mortality was assessed daily, and surviving mice were sacrificed followed by the above analyses together with immunohistochemical localization of CD8, tumor necrosis factor-α, CD4, interleukin-1β, transforming growth factor-β, inducible nitric oxide synthase and basic fibroblast growth factor. Compared to bleomycin-treated mice, animals that received also PEA-um(®) (3 or 10mg/kg) had significantly decreased weight loss, mortality, inflammation, lung damage at the histological level, and lung fibrosis at 7 and 21days. PEA-um(®) (1mg/kg) did not significantly inhibit the inflammation response and lung fibrosis. This study demonstrates that PEA-um(®) (3 and 10mg/kg) reduces the extent of lung inflammation in a mouse model of idiopathic pulmonary fibrosis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Targeting Bcl-2/Bcl-XL induces antitumor activity in uveal melanoma patient-derived xenografts.

PubMed

Némati, Fariba; de Montrion, Catherine; Lang, Guillaume; Kraus-Berthier, Laurence; Carita, Guillaume; Sastre-Garau, Xavier; Berniard, Aurélie; Vallerand, David; Geneste, Olivier; de Plater, Ludmilla; Pierré, Alain; Lockhart, Brian; Desjardins, Laurence; Piperno-Neumann, Sophie; Depil, Stéphane; Decaudin, Didier

2014-01-01

Uveal melanoma (UM) is associated with a high risk of metastases and lack of efficient therapies. Reduced capacity for apoptosis induction by chemotherapies is one obstacle to efficient treatments. Human UM is characterized by high expression of the anti-apoptotic protein Bcl-2. Consequently, regulators of apoptosis such as Bcl-2 family inhibitors may constitute an attractive approach to UM therapeutics. In this aim, we have investigated the efficacy of the Bcl-2/Bcl-XL inhibitor S44563 on 4 UM Patient-Derived Xenografts (PDXs) and derived-cell lines. Four well characterized UM PDXs were used for in vivo experiments. S44563 was administered alone or combined with fotemustine either concomitantly or after the alkylating agent. Bcl-2, Bcl-XL, and Mcl-1 expressions after S44563 administration were evaluated by immunohistochemistry (IHC). S44563 administered alone by at 50 and 100 mg/kg i.p. induced a significant tumour growth inhibition in only one xenograft model with a clear dose effect. However, when S44563 was concomitantly administered with fotemustine, we observed a synergistic activity in 3 out of the 4 tested models. In addition, S44563 administered after fotemustine induced a tumour growth delay in 2 out of 3 tested xenografts. Finally, IHC analyses showed that Bcl-2, Bcl-XL, and Mcl-1 expression were not modified after S44563 administration. The novel anti-apoptotic experimental compound S44563, despite a relative low efficacy when administered alone, increased the efficacy of fotemustine in either concomitant or sequential combinations or indeed subsequent to fotemustine. These data support further exploration of potential therapeutic effect of Bcl-2/Bcl-xl inhibition in human UM.

VizieR Online Data Catalog: Herschel FIR spectra of GOALS galaxies (Diaz-Santos+, 2017)

NASA Astrophysics Data System (ADS)

Diaz-Santos, T.; Armus, L.; Charmandaris, V.; Lu, N.; Stierwalt, S.; Stacey, G.; Malhotra, S.; van der Werf, P. P.; Howell, J. H.; Privon, G. C.; Mazzarella, J. M.; Goldsmith, P. F.; Murphy, E. J.; Barcos-Munoz, L.; Linden, S. T.; Inami, H.; Larson, K. L.; Evans, A. S.; Appleton, P.; Iwasawa, K.; Lord, S.; Sanders, D. B.; Surace, J. A.

2018-04-01

We have obtained FIR spectroscopic observations for 200 luminous infrared galaxies (LIRG) systems from the Great Observatories All-Sky LIRG Survey (GOALS; Armus+ 2009PASP..121..559A) using the Integral Field Spectrometer (IFS) of the PACS instrument on board Herschel. Since some targets contain multiple components, there are 241 individual galaxies with available spectra in at least one emission line. Most of the data were collected as part of our OT1 and OT2 programs (OT1larmus1, OT2larmus1; P.I.: L. Armus), accounting for more than 200hr of observing time in total. Additional observations that are publicly available in the Herschel archive were included from various projects. The main programs from where these complementary data were gathered are KPGTesturm1 (P.I.: E. Sturm), KPOTpvanderw1 (PI: P. van der Werf), and OT1dweedman1 (P.I.: D. Weedman). The IFS on PACS is able to perform simultaneous spectroscopy in the 51-73 or 70-105um and the 102-210um ranges. In addition to the PACS/IFS spectra, we obtained observations of the [NII]205 emission line using the SPIRE FTS for 121 galaxies in the GOALS sample (Lu+ 2017, J/ApJS/230/1 ; OT1nlu1; P.I.: N. Lu). As part of the Spitzer GOALS legacy program, all galaxies observed with Herschel/PACS have available Spitzer/IRS low-resolution, R~60-120 (SL module: 5.2-14.5um; LL module: 14-38um), and medium-resolution, R~600 (SH module: 9.9-19.6um; LH module: 18.7-37.2um), slit spectroscopy. (3 data files).

University of Malaya dental students' attitudes towards communication skills learning: implications for dental education.

PubMed

Nor, Nor Azlida M; Yusof, Zamros Y M; Shahidan, Mohd Noor F M

2011-12-01

The Ministry of Higher Education in Malaysia has called for the implementation of a soft skills module in all public universities in Malaysia. In response to this and as part of curriculum development efforts for a new integrated program for 2011, a study was undertaken to improve the University of Malaya (UM) Faculty of Dentistry's communication skills course. One of the study objectives was to investigate dental students' attitudes towards communication skills learning and the association between their attitudes and demographic and education-related characteristics. A cross-sectional survey--using a self-administered twenty-four-item adapted Communication Skills Attitude Scale (CSAS) that contained both positive (PAS) and negative (NAS) attitude subscales--was carried out targeting all final-year dental students at the UM and the Universiti Kebangsaan Malaysia (UKM). A total of 148 students completed the survey, yielding a response rate of 88.1 percent. Overall, UKM students had significantly more positive attitudes towards communication skills learning (PAS score: mean=48.69, SD=4.48, p<0.001) than UM students (mean=46.03, SD=4.22). There was no statistically significant difference in negative attitudes between the two groups. UKM students with more positive attitudes tended to be female (p<0.05). UM students with more negative attitudes perceived themselves as poor communicators (p<0.05), and UKM students with more negative attitudes tended to have poor English proficiency (p<0.05). This study found that both UM and UKM final-year dental students have positive and negative attitudes towards learning communication skills. These attitudes were significantly associated with certain background and education-related attributes. Outcomes of this study served as a valuable guide in strengthening the communication skills course for the UM's new, integrated dental curriculum.

406 E Grand, October 2010, Lindsay Light Radiological Survey

EPA Pesticide Factsheets

The field gamma measurements within the excavation and the spoil materials generated during the excavation process did not exceed the respective threshold values previously stated and ranged from a minim um of 1, 120 cpm to a maxim um of 6,640 cpm.

VizieR Online Data Catalog: SCUBA-2 high-redshift galaxies sample (Barger+, 2014)

NASA Astrophysics Data System (ADS)

Barger, A. J.; Cowie, L. L.; Chen, C.-C.; Owen, F. N.; Wang, W.-H.; Casey, C. M.; Lee, N.; Sanders, D. B.; Williams, J. P.

2017-05-01

We obtained 25.4 hr of observations on the CDF-N with SCUBA-2 on the JCMT during observing runs in 2012 and 2013. The data were obtained using a mixture of scanning modes and under a variety of weather conditions. Using the CV Daisy scanning mode (detailed information about the SCUBA-2 scan patterns can be found in Holland et al. 2013MNRAS.430.2513H), we obtained a 2.2 hr observation in band 1 weather (225 GHz opacity<0.05) and a 16.5 hr observation in band 2 weather (225 GHz opacity ~0.05-0.08). We also obtained a 6.7 hr observation in band 2 weather using the pong-900 scanning mode. While SCUBA-2 observes at both 450 um and 850 um simultaneously, there are too few sources directly detected at 450 um in our data to be interesting. Thus, we only use the 850 um data in our subsequent analysis. (1 data file).

Utilization management affects health care practices at Walter Reed Army Medical Center: analytical methods applied to decrease length of stay and assign appropriate level of care.

PubMed

Phillips, J S; Hamm, C K; Pierce, J R; Kussman, M J

1999-12-01

The Department of Defense has embraced utilization management (UM) as an important tool to control and possibly decrease medical costs. Budgetary withholds have been taken by the Office of the Assistant Secretary of Defense (Health Affairs) to encourage the military services to implement UM programs. In response, Walter Reed Army Medical Center implemented a UM program along with other initiatives to effect changes in the delivery of inpatient care. This paper describes this UM program and other organizational initiatives, such as the introduction of new levels of care in an attempt to effect reductions in length of stay and unnecessary admissions. We demonstrate the use of a diversity of databases and analytical methods to quantify improved utilization and management of resources. The initiatives described significantly reduced hospital length of stay and inappropriate inpatient days. Without solid command and clinical leadership support and empowerment of the professional staffs, these significant changes and improvements could not have occurred.

Differences in Hospital Managers’, Unit Managers’, and Health Care Workers’ Perceptions of the Safety Climate for Respiratory Protection

PubMed Central

Peterson, Kristina; Rogers, Bonnie M. E.; Brosseau, Lisa M.; Payne, Julianne; Cooney, Jennifer; Joe, Lauren; Novak, Debra

2017-01-01

This article compares hospital managers’ (HM), unit managers’ (UM), and health care workers’ (HCW) perceptions of respiratory protection safety climate in acute care hospitals. The article is based on survey responses from 215 HMs, 245 UMs, and 1,105 HCWs employed by 98 acute care hospitals in six states. Ten survey questions assessed five of the key dimensions of safety climate commonly identified in the literature: managerial commitment to safety, management feedback on safety procedures, coworkers’ safety norms, worker involvement, and worker safety training. Clinically and statistically significant differences were found across the three respondent types. HCWs had less positive perceptions of management commitment, worker involvement, and safety training aspects of safety climate than HMs and UMs. UMs had more positive perceptions of management’s supervision of HCWs’ respiratory protection practices. Implications for practice improvements indicate the need for frontline HCWs’ inclusion in efforts to reduce safety climate barriers and better support effective respiratory protection programs and daily health protection practices. PMID:27056750

Differences in Hospital Managers', Unit Managers', and Health Care Workers' Perceptions of the Safety Climate for Respiratory Protection.

PubMed

Peterson, Kristina; Rogers, Bonnie M E; Brosseau, Lisa M; Payne, Julianne; Cooney, Jennifer; Joe, Lauren; Novak, Debra

2016-07-01

This article compares hospital managers' (HM), unit managers' (UM), and health care workers' (HCW) perceptions of respiratory protection safety climate in acute care hospitals. The article is based on survey responses from 215 HMs, 245 UMs, and 1,105 HCWs employed by 98 acute care hospitals in six states. Ten survey questions assessed five of the key dimensions of safety climate commonly identified in the literature: managerial commitment to safety, management feedback on safety procedures, coworkers' safety norms, worker involvement, and worker safety training. Clinically and statistically significant differences were found across the three respondent types. HCWs had less positive perceptions of management commitment, worker involvement, and safety training aspects of safety climate than HMs and UMs. UMs had more positive perceptions of management's supervision of HCWs' respiratory protection practices. Implications for practice improvements indicate the need for frontline HCWs' inclusion in efforts to reduce safety climate barriers and better support effective respiratory protection programs and daily health protection practices. © 2016 The Author(s).

Unconsummated marriages: a separate and different clinical entity.

PubMed

Gindin, Leon Roberto; Resnicoff, Diana

2002-01-01

We bring our experience in the treatment of unconsummated marriages (UM). We postulate that it is an independent clinical entity. Since 1991, 199 couples with UM have sought treatment in our center in Buenos Aires. A new approach to this problem is based on an intensive treatment session that lasts a whole day and a pledge to pay only if therapy succeeds. The outcome was a success (97%) with coitus consummation. We make a long-term follow up. The advantages are the brevity of the treatment and lack of desertions. We postulate that UM cannot be approached with an individual perspective or with the usual psychotherapy techniques.

An Overview of Reactor Concepts, a Survey of Reactor Designs.

DTIC Science & Technology

1985-02-01

may be very different. HTGRs may use highly enriched uranium, thereby yielding better fuel economy and a reduc- tion of the actual core size for a...specific power level. The HTGR core may have fuel and control rods placed in graphite arrays similar to PWR core con- figuration, or they may have fuel ...rods are pulled out. A Peach Bottom core design is another HTGR design. This design is featured by the fuel pin’s ability to purge itself of fission

TRAC-PD2 posttest analysis of the CCTF Evaluation-Model Test C1-19 (Run 38). [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Motley, F.

The results of a Transient Reactor Analysis Code posttest analysis of the Cylindral Core Test Facility Evaluation-Model Test agree very well with the results of the experiment. The good agreement obtained verifies the multidimensional analysis capability of the TRAC code. Because of the steep radial power profile, the importance of using fine noding in the core region was demonstrated (as compared with poorer results obtained from an earlier pretest prediction that used a coarsely noded model).

Methods and benefits of experimental seismic evaluation of nuclear power plants. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-07-01

This study reviews experimental techniques, instrumentation requirements, safety considerations, and benefits of performing vibration tests on nuclear power plant containments and internal components. The emphasis is on testing to improve seismic structural models. Techniques for identification of resonant frequencies, damping, and mode shapes, are discussed. The benefits of testing with regard to increased damping and more accurate computer models are oulined. A test plan, schedule and budget are presented for a typical PWR nuclear power plant.

BNL severe-accident sequence experiments and analysis program. [PWR; BWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greene, G.A.; Ginsberg, T.; Tutu, N.K.

1983-01-01

In the analysis of degraded core accidents, the two major sources of pressure loading on light water reactor containments are: steam generation from core debris-water thermal interactions; and molten core-concrete interactions. Experiments are in progress at BNL in support of analytical model development related to aspects of the above containment loading mechanisms. The work supports development and evaluation of the CORCON (Muir, 1981) and MARCH (Wooton, 1980) computer codes. Progress in the two programs is described.

Crack growth testing on Cold Worked Alloy 690 in Primary Water Environment

NASA Astrophysics Data System (ADS)

Tice, David R.; Medway, Stuart L.; Platts, Norman; Stairmand, John W.

While plant experience so far has shown excellent resistance of Alloy 690 to stress corrosion cracking in PWR primary water environments, laboratory tests have reported that susceptibility may be enhanced substantially by non-uniform cold working, particularly when the plane of crack growth is in the plane of rolling or forging. The Alloy 690 program aims to further the understanding of the mechanisms behind this susceptibility and the heat-to-heat variability reported for different materials.

Advanced Information Systems Design: Technical Basis and Human Factors Review Guidance

DTIC Science & Technology

2000-03-01

D ., Wise, J ., and Hanes, L., "An Evaluation of Nuclear Power Plant Safety Parameter Display Systems," Proceedings of the Human Factors Society 25th...Reactor (PWR) (Source: Reprinted with permission from Woods, D ., Wise, J ., and Hanes, L., "An Evaluation of Nuclear Power Plant Safety Parameter...Dials display rpCJni?3 (b) Fluid-Tanks display B (c) Seesaw display I 72 CF \\^- J B ’ V ’II ’ ( d ) Mimic display B E * • \\ ^r 7

Hot zero power reactor calculations using the Insilico code

DOE PAGES

Hamilton, Steven P.; Evans, Thomas M.; Davidson, Gregory G.; ...

2016-03-18

In this paper we describe the reactor physics simulation capabilities of the insilico code. A description of the various capabilities of the code is provided, including detailed discussion of the geometry, meshing, cross section processing, and neutron transport options. Numerical results demonstrate that the insilico SP N solver with pin-homogenized cross section generation is capable of delivering highly accurate full-core simulation of various PWR problems. Comparison to both Monte Carlo calculations and measured plant data is provided.

33 CFR 208.11 - Regulations for use of storage allocated for flood control or navigation and/or project operation...

Code of Federal Regulations, 2011 CFR

2011-07-01

... VA Pwr. Glen Elder Dam & Waconda Lk KS Mitchel Solomon R FIM 722.3204.8 1488.31455.6 1455.61428.0... 820 PL 78-534 USBR. Kirwin Dam & Res KS Phillips N Fork Solomon R F ICR 215.1 89.6 1757.3 1729.2 1729... Webster Dam & Res KS Rocks S Fork Solomon R F IRC 183.4 72.1 1923.7 1892.5 1892.5 1860.0 8480 3772 3772...

33 CFR 208.11 - Regulations for use of storage allocated for flood control or navigation and/or project operation...

Code of Federal Regulations, 2010 CFR

2010-07-01

... VA Pwr. Glen Elder Dam & Waconda Lk KS Mitchel Solomon R FIM 722.3204.8 1488.31455.6 1455.61428.0... 820 PL 78-534 USBR. Kirwin Dam & Res KS Phillips N Fork Solomon R F ICR 215.1 89.6 1757.3 1729.2 1729... Webster Dam & Res KS Rocks S Fork Solomon R F IRC 183.4 72.1 1923.7 1892.5 1892.5 1860.0 8480 3772 3772...

Determination of tube-to-tube support interaction characteristics. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haslinger, K.H.

Tube-to-tube support interaction characteristics were determined on a multi-span tube geometry representative of the hot-leg side of the C-E, System 80 steam generator design. Results will become input for an autoclave type wear test program on steam generator tubes, performed by Kraftwerk Union (KWU). Correlation of test data reported here with similar data obtained from the wear tests will be performed in an attempt to make predictions about the long-term fretting behavior of steam generator tubes.

Advanced techniques for repair of irradiated PWR fuel assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knaab, H.; Westphal, M.

Kraftwerk union has recently designed and built a portable repair unit for use in nuclear power plants for repair of defective fuel assemblies where space limitations do not allow permanent installation of repair equipment. This new equipment is designed to be easily disassembled and decontaminated. The main component of the equipment is the fuel assembly reconstitution unit (FARU) which is placed on the floor of the spent fuel pool. The use of the FARU is described in the paper.

Survey and Analysis of Environmental Requirements for Shipboard Electronic Equipment Applications. Appendix A. Volume 2.

DTIC Science & Technology

1991-07-31

INTELLIGENT SCSI DMV-719 MAS MIL CONTROLLER DY-4 SYSTEMS BYTE-WIDE MEMORY CARD DMV-536 MEM MIL DY-4 SYSTEMS POWER SUPPLY UNIT DMV-870 PWR MIL P age No. 5 06/10...FORCE COMPUTERS PROCESSOR CPU-386 SERIES SBC COM FORCE COMPUTERS ADVANCED SYSTEM CONTROL ASCU -1/2 SBC COM UNITI FORCE COMPUTERS GRAPHICS CONTROLLER AGC...RECORD VENDOR: JANZ COMPUTER AG DIVISION: VENDOR ADDRESS: Im Doerener Feld 3 D-4790 Paderborn Germany MARKETING: Johannes Kunz TECHNICAL: Arnulf

Application of the TEMPEST computer code for simulating hydrogen distribution in model containment structures. [PWR; BWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trent, D.S.; Eyler, L.L.

In this study several aspects of simulating hydrogen distribution in geometric configurations relevant to reactor containment structures were investigated using the TEMPEST computer code. Of particular interest was the performance of the TEMPEST turbulence model in a density-stratified environment. Computed results illustrated that the TEMPEST numerical procedures predicted the measured phenomena with good accuracy under a variety of conditions and that the turbulence model used is a viable approach in complex turbulent flow simulation.

JPRS Report Science & Technology Japan

DTIC Science & Technology

1989-03-02

Oxychlorides MOCln_2 (Organic Metal Salts) Alkoxides M(OR)n Acetylacetonate M(C5H702)n Acetates M(C2H302)n Oxalates M(C204)n/2 2.2 Hydrolysis and Gel...more deeply understanding hydrothermal dynamics during not only a major rupture LOCA but also a minor rupture LOCA and clarifying the combination of... hydrothermal dynamics of the coolant from the beginning of LOCA to its end, using a scale model of PWR (pressurized water reactor). Under the ROSA-III Plan

NUTRIENT LIMITATION OF PHYTOPLANKTON GROWTH AND PHYSIOLOGY IN A SUBTROPICAL ESTUARY (PENSACOLA BAY, FL)

EPA Science Inventory

Phytoplankton nutrient limitation was studied in a sub-estuary of lower Pensacola Bay using several techniques. Results for <5 um and . 5 um phytoplankton were similar. Nutrient-addition bioassays indicated year-round nutrient limitation, in contrast to seasonal patterns often ...

Unit 5, STA. 50+00+RB, retaining wall at First U.M. Churchdetail ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Unit 5, STA. 50+00+RB, retaining wall at First U.M. Church-detail - Johnstown Local Flood Protection Project, Beginning on Conemaugh River approx 3.8 miles downstream from confluence of Little Conemaugh & Stony Creek Rivers at Johnstown, Johnstown, Cambria County, PA

DIRECT-DEPOSITION INFRARED SPECTROMETRY WITH GAS AND SUPERCRITICAL FLUID CHROMATOGRAPHY

EPA Science Inventory

A direct-deposition Fourier transform infrared (FT-IR) system has been evaluated for applicability to gas chromatography (GC) and supercritical fluid chromatography (SFC) of environmental analytes. A 100-um i.d. fused-silica transfer line was used for GC, and a 50-um transfer lin...

Linguistic camouflage in girls with autism spectrum disorder.

PubMed

Parish-Morris, Julia; Liberman, Mark Y; Cieri, Christopher; Herrington, John D; Yerys, Benjamin E; Bateman, Leila; Donaher, Joseph; Ferguson, Emily; Pandey, Juhi; Schultz, Robert T

2017-01-01

Autism spectrum disorder (ASD) is diagnosed more frequently in boys than girls, even when girls are equally symptomatic. Cutting-edge behavioral imaging has detected "camouflaging" in girls with ASD, wherein social behaviors appear superficially typical, complicating diagnosis. The present study explores a new kind of camouflage based on language differences. Pauses during conversation can be filled with words like UM or UH, but research suggests that these two words are pragmatically distinct (e.g., UM is used to signal longer pauses, and may correlate with greater social communicative sophistication than UH). Large-scale research suggests that women and younger people produce higher rates of UM during conversational pauses than do men and older people, who produce relatively more UH. Although it has been argued that children and adolescents with ASD use UM less often than typical peers, prior research has not included sufficient numbers of girls to examine whether sex explains this effect. Here, we explore UM vs. UH in school-aged boys and girls with ASD, and ask whether filled pauses relate to dimensional measures of autism symptom severity. Sixty-five verbal school-aged participants with ASD (49 boys, 16 girls, IQ estimates in the average range) participated, along with a small comparison group of typically developing children (8 boys, 9 girls). Speech samples from the Autism Diagnostic Observation Schedule were orthographically transcribed and time-aligned, with filled pauses marked. Parents completed the Social Communication Questionnaire and the Vineland Adaptive Behavior Scales. Girls used UH less often than boys across both diagnostic groups. UH suppression resulted in higher UM ratios for girls than boys, and overall filled pause rates were higher for typical children than for children with ASD. Higher UM ratios correlated with better socialization in boys with ASD, but this effect was driven by increased use of UH by boys with greater symptoms. Pragmatic language markers distinguish girls and boys with ASD, mirroring sex differences in the general population. One implication of this finding is that typical-sounding disfluency patterns (i.e., reduced relative UH production leading to higher UM ratios) may normalize the way girls with ASD sound relative to other children, serving as "linguistic camouflage" for a naïve listener and distinguishing them from boys with ASD. This first-of-its-kind study highlights the importance of continued commitment to understanding how sex and gender change the way that ASD manifests, and illustrates the potential of natural language to contribute to objective "behavioral imaging" diagnostics for ASD.

Telescópio de patrulhamento solar em 12 GHz

NASA Astrophysics Data System (ADS)

Utsumi, F.; Costa, J. E. R.

2003-08-01

O telescópio de patrulhamento solar é um instrumento dedicado à observação de explosões solares com início de suas operações em janeiro de 2002, trabalhando próximo ao pico de emissão do espectro girossincrotrônico (12 GHz). Trata-se de um arranjo de três antenas concebido para a detecção de explosões e determinação em tempo real da localização da região emissora. Porém, desde sua implementação em uma montagem equatorial movimentada por um sistema de rotação constante (15 graus/hora) o rastreio apresentou pequenas variações de velocidade e folgas nas caixas de engrenagens. Assim, tornou-se necessária a construção de um sistema de correção automática do apontamento que era de fundamental importância para os objetivos do projeto. No segundo semestre de 2002 empreendemos uma série de tarefas com o objetivo de automatizar completamente o rastreio, a calibração, a aquisição de dados, controle de ganhos, offsets e transferência dos dados pela internet através de um projeto custeado pela FAPESP. O rastreio automático é realizado através de um inversor que controla a freqüência da rede de alimentação do motor de rastreio podendo fazer micro-correções na direção leste-oeste conforme os radiômetros desta direção detectem uma variação relativa do sinal. Foi adicionado também um motor na direção da declinação para correção automática da variação da direção norte-sul. Após a implementação deste sistema a precisão do rastreio melhorou para um desvio máximo de 30 segundos de arco, o que está muito bom para este projeto. O Telescópio se encontra em funcionamento automático desde março de 2003 e já conta com várias explosões observadas após a conclusão desta fase de automação. Estamos apresentando as explosões mais intensas do período e com as suas respectivas posições no disco solar.

Evaluation of Unified Model Microphysics in High-resolution NWP Simulations Using Polarimetric Radar Observations

NASA Astrophysics Data System (ADS)

Johnson, Marcus; Jung, Youngsun; Dawson, Daniel; Supinie, Timothy; Xue, Ming; Park, Jongsook; Lee, Yong-Hee

2018-07-01

The UK Met Office Unified Model (UM) is employed by many weather forecasting agencies around the globe. This model is designed to run across spatial and time scales and known to produce skillful predictions for large-scale weather systems. However, the model has only recently begun running operationally at horizontal grid spacings of ˜1.5 km [e.g., at the UK Met Office and the Korea Meteorological Administration (KMA)]. As its microphysics scheme was originally designed and tuned for large-scale precipitation systems, we investigate the performance of UM microphysics to determine potential inherent biases or weaknesses. Two rainfall cases from the KMA forecasting system are considered in this study: a Changma (quasi-stationary) front, and Typhoon Sanba (2012). The UM output is compared to polarimetric radar observations in terms of simulated polarimetric radar variables. Results show that the UM generally underpredicts median reflectivity in stratiform rain, producing high reflectivity cores and precipitation gaps between them. This is partially due to the diagnostic rain intercept parameter formulation used in the one-moment microphysics scheme. Model drop size is generally both underand overpredicted compared to observations. UM frozen hydrometeors favor generic ice (crystals and snow) rather than graupel, which is reasonable for Changma and typhoon cases. The model performed best with the typhoon case in terms of simulated precipitation coverage.

International Space Station Urine Monitoring System Functional Integration and Science Testing

NASA Technical Reports Server (NTRS)

Rodriquez, Branelle R.; Broyan, James Lee, Jr.

2011-01-01

Exposure to microgravity during human spaceflight needs to be better understood as the human exploration of space requires longer duration missions. It is known that long term exposure to microgravity causes bone loss. Measuring the calcium and other metabolic byproducts in a crew member s urine can evaluate the effectiveness of bone loss countermeasures. The International Space Station (ISS) Urine Monitoring System (UMS) is an automated urine collection device designed to collect urine, separate the urine and air, measure the void volume, and allow for syringe sampling. Accurate measuring and minimal cross-contamination is essential to determine bone loss and the effectiveness of countermeasures. The ISS UMS provides minimal cross-contamination (<0.7 mL urine) and has volume accuracy of 2% between 100 to 1000 mL urine voids. Designed to provide a non-invasive means to collect urine samples from crew members, the ISS UMS operates in-line with the Node 3 Waste and Hygiene Compartment (WHC). The ISS UMS has undergone modifications required to interface with the WHC, including material changes, science algorithm improvements, and software platform revisions. Integrated functional testing was performed to determine the pressure drop, air flow rate, and the maximum amount of fluid capable of being discharged from the UMS to the WHC. This paper will detail the results of the science and the functional integration tests.

Darwin als Sehhilfe für die Psychologie - Evolutionspsychologie

NASA Astrophysics Data System (ADS)

Schwab, Frank

Im Folgenden geht es um Einäugige, stereoskopisches Sehen, weite und enge Horizonte, Monokel und Sonnenbrillen. Der Beitrag versucht die Metapher des Sehens und der Sehhilfen anzuwenden, um so zu verdeutlichen, welchen Gewinn die herkömmliche Psychologie durch die Verwendung einer Darwin'schen Brille erlangen kann.

Application of LEED (trademark) and SPiRiT to a Proposed Building Design

DTIC Science & Technology

2003-03-01

TOTAL AREA S CAT ARLOC INSTALLATION NO CODE C QTY UM OCPD F CODE 1) 24004 Aberdeen Provi E1890...ARLOC INSTALLATION NO CODE C QTY UM OCPD F CODE 1) 24004 Aberdeen Provi E3832 31010 P 13,000 SF 13,000 R

Evolution and Persistence of 5-um Hot Spots at the Galileo Probe entry Latitude

NASA Technical Reports Server (NTRS)

Fisher, B. M.

1997-01-01

We present a study on the longtudinal locations, morphology and evolution of the 5-um hot spots at 6.5 deg. N latitude (planetocentric), from an extensive IRTF-NSFCAM data set spanning more that 3 years, which includes the date of the Galileo Probe entry.

Antimalarial and antileishmanial activities of phytophenolics and their synthetic analogues

USDA-ARS?s Scientific Manuscript database

Thirty-seven phytophenolics and their synthetic analogues were evaluated for activity against two protozoal pathogens, Leishmania donovani and Plasmodium falciparum (D6 and W2 clone), respectively. 4,6-Dimethoxyaurone demonstrated the highest activity with IC50 values of 13.2 uM and 16.9 uM against ...

VizieR Online Data Catalog: PACS photometry of FIR faint stars (Klaas+, 2018)

NASA Astrophysics Data System (ADS)

Klaas, U.; Balog, Z.; Nielbock, M.; Mueller, T. G.; Linz, H.; Kiss, Cs.

2018-01-01

70, 100 and 160um photometry of FIR faint stars from PACS scan map and chop/nod measurements. For scan maps also the photometry of the combined scan and cross-scan maps (at 160um there are usually two scan and cross-scan maps each as complements to the 70 and 100um maps) is given. Note: Not all stars have measured fluxes in all three filters. Scan maps: The main observing mode was the point-source mini-scan-map mode; selected scan map parameters are given in column mparam. An outline of the data processing using the high-pass filter (HPF) method is presented in Balog et al. (2014ExA....37..129B). Processing proceeded from Herschel Science Archive SPG v13.1.0 level 1 products with HIPE version 15 build 165 for 70 and 100um maps and from Herschel Science Archive SPG v14.2.0 level 1 products with HIPE version 15 build 1480 for 160um maps. Fluxes faper were obtained by aperture photometry with aperture radii of 5.6, 6.8 and 10.7 arcsec for the 70, 100 and 160um filter, respectively. Noise per pixel sigpix was determined with the histogram method, described in this paper, for coverage values greater than or equal to 0.5*maximum coverage. The number of map pixels (1.1, 1.4, and 2.1 arcsec pixel size, respectively) inside the photometric aperture is Naper = 81.42, 74.12, and 81.56, respectively. The corresponding correction factors for correlated noise are fcorr = 3.13, 2.76, and 4.12, respectively. The noise for the photometric aperture is calculated as sig_aper=sqrt(Naper)*fcorr*sigpix. Signal-to-noise ratios are determined as S/N=faper/sigaper. Aperture-correction factors to derive the total flux are caper = 1.61, 1.56 and 1.56 for the 70, 100 and 160um filter, respectively. Applied colour-correction factors for a 5000K black-body SED are cc = 1.016, 1.033, and 1.074 for the 70, 100, and 160um filter, respectively. The final stellar flux is derived as fstar=faper*caper/cc. Maximum and minimum FWHM of the star PSF are determined by an elliptical fit of the intensity profile. Chop/nod observations: The chop/nod point-source mode is described in this paper. An outline of the data processing is presented in Nielbock et al. (2013ExA....36..631N). Processing proceeded from Herschel Science Archive SPG v11.1.0 level 1 products with HIPE version 13 build 2768. Gyro correction was applied for most of the cases to improve the pointing reconstruction performance. Fluxes faper were obtained by aperture photometry with aperture radii of 5.6, 6.8 and 10.7 arcsec for the 70, 100 and 160um filter, respectively. Noise per pixel sigpix was determined with the histogram method, described in this paper, for coverage values greater than or equal to 0.5*maximum coverage. The number of map pixels (1.1, 1.4, and 2.1 arcsec pixel size, respectively) inside the photometric aperture is Naper = 81.42, 74.12, and 81.56, respectively. The corresponding correction factors for correlated noise are fcorr = 6.33, 4.22, and 7.81, respectively. The noise for the photometric aperture is calculated as sigaper=sqrt(Naper)*fcorr*sigpix. Signal-to-noise ratios are determined as S/N=faper/sigaper. Aperture-correction factors to derive the total flux are caper = 1.61, 1.56 and 1.56 for the 70, 100 and 160um filter, respectively. Applied colour-correction factors for a 5000K black-body SED are cc = 1.016, 1.033, and 1.074 for the 70, 100, and 160um filter, respectively. Maximum and minimum FWHM of the star PSF are determined by an elliptical fit of the intensity profile. (7 data files).

Representing metabolic pathway information: an object-oriented approach.

PubMed

Ellis, L B; Speedie, S M; McLeish, R

1998-01-01

The University of Minnesota Biocatalysis/Biodegradation Database (UM-BBD) is a website providing information and dynamic links for microbial metabolic pathways, enzyme reactions, and their substrates and products. The Compound, Organism, Reaction and Enzyme (CORE) object-oriented database management system was developed to contain and serve this information. CORE was developed using Java, an object-oriented programming language, and PSE persistent object classes from Object Design, Inc. CORE dynamically generates descriptive web pages for reactions, compounds and enzymes, and reconstructs ad hoc pathway maps starting from any UM-BBD reaction. CORE code is available from the authors upon request. CORE is accessible through the UM-BBD at: http://www. labmed.umn.edu/umbbd/index.html.

VizieR Online Data Catalog: Herschel FIR observations of NGC3603 (Di Cecco+, 2015)

NASA Astrophysics Data System (ADS)

di Cecco, A.; Faustini, F.; Paresce, F.; Correnti, M.; Calzoletti, L.

2015-06-01

The cloud complex surrounding NGC 3603 YC was observed by Herschel SPIRE/PACS during the Hi-GAL Survey (Molinari et al. 2010A&A...518L.100M, 2010PASP..122..314M), a Key Programme that mapped the Galactic plane in five photometric bands (70, 160, 250, 350, and 500um). The MSX (Egan et al. 2003AAS...203.5708E) images were taken at (wavelengths) 8.3, 12.1, 14.7, and 21.3um using the scan observing mode, and the WISE (Wright et al. 2010AJ....140.1868W) images were acquired in freeze-frame scan mode at 3.4, 4.6, 12, and 22um. (2 data files).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schulz, H.

In the updating of the Guidelines for PWR`s of the {open_quotes}Reaktor-Sicherheitskommission{close_quotes} (RSK) in 1981 the requirements on the design have been changed with respect to the postulated leaks and breaks in the primary pressure boundary. The major change was a revision in the requirements for pipe whip protection. As a logical consequence of the {open_quotes}concept of basic safety{close_quotes} a guillotine type break or any other break type resulting in a large opening is not postulated any longer for the calculation of reaction and jet forces. As an upper limit for a leak an area of 0, 1 A (A =more » open cross section of the pipe) is postulated. This decision was based on a general assessment of the present PWR system design in Germany. Since then a number of piping systems have been requalified in the older nuclear power plants to comply with the break preclusion concept. Also a number of extensions of the concept have been developed to cover also leak-assumptions for branch pipes. Furthermore due considerations have been given to other aspects which could contribute to a leak development in the primary circuit, like vessel penetrations, manhole covers, flanges, etc. Now the break preclusion concept originally applied to the main piping has been developed into an integrated concept for the whole pressure boundary within the containment and will be applied also in the periodic safety review of present nuclear power plants.« less

Design and Laboratory Evaluation of Future Elongation and Diameter Measurements at the Advanced Test Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

K. L. Davis; D. L. Knudson; J. L. Rempe

New materials are being considered for fuel, cladding, and structures in next generation and existing nuclear reactors. Such materials can undergo significant dimensional and physical changes during high temperature irradiations. In order to accurately predict these changes, real-time data must be obtained under prototypic irradiation conditions for model development and validation. To provide such data, researchers at the Idaho National Laboratory (INL) High Temperature Test Laboratory (HTTL) are developing several instrumented test rigs to obtain data real-time from specimens irradiated in well-controlled pressurized water reactor (PWR) coolant conditions in the Advanced Test Reactor (ATR). This paper reports the status ofmore » INL efforts to develop and evaluate prototype test rigs that rely on Linear Variable Differential Transformers (LVDTs) in laboratory settings. Although similar LVDT-based test rigs have been deployed in lower flux Materials Testing Reactors (MTRs), this effort is unique because it relies on robust LVDTs that can withstand higher temperatures and higher fluxes than often found in other MTR irradiations. Specifically, the test rigs are designed for detecting changes in length and diameter of specimens irradiated in ATR PWR loops. Once implemented, these test rigs will provide ATR users with unique capabilities that are sorely needed to obtain measurements such as elongation caused by thermal expansion and/or creep loading and diameter changes associated with fuel and cladding swelling, pellet-clad interaction, and crud buildup.« less

Pretest analysis of Semiscale Mod-3 baseline test S-07-8 and S-07-9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fineman, C.P.; Steiner, J.L.; Snider, D.M.

This document contains a pretest analysis of the Semiscale Mod-3 system thermal-hydraulic response for the second and third integral tests in Test Series 7 (Tests S-07-8 and S-07-9). Test Series 7 is the first test series to be conducted with the Semiscale Mod-3 system. The design of the Mod-3 system includes an improved representation of certain portions of a pressurized water reactor (PWR) when compared to the previously operated Semiscale Mod-1 system. The improvements include a new vessel which contains a full length (3.66 m) core, a full length upper plenum and upper head, and an external downcomer. An activemore » pump and active steam generator scaled to their pressurized water reactor (PWR) counterparts have been added to the broken loop. The upper head design includes the capability to simulate emergency core coolant (ECC) injection into this region. Test Series 7 is divided into three groups of tests that emphasize the evaluation of the Mod-3 system performance during different phases of the loss-of-coolant experiment (LOCE) transient. The last test group, which includes Tests S-07-8 and S-07-9, will be used to evaluate the integral behavior of the system. The previous two test groups were used to evaluate the blowdown behavior and the reflood behavior of the system. 3 refs., 35 figs., 12 tabs.« less

Development of modified MDA (M-MDA), PWR fuel cladding tube for high duty operation in future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watanabe, Seiichi; Kido, Toshiya; Arakawa, Yasushi

2007-07-01

A new cladding material of M-MDA has been developed in order to prepare for a strong growing demand for advanced fuel which can maintain its integrity even under high duties due to more efficient operation such as higher burnup, higher LHR, and longer operation cycle which will contribute the suppression of environmental burdens like CO{sub 2} emission. The main aim of M-MDA is to have excellent corrosion resistance while the other properties are inherited from MDA, which has been adopted to the step 2 fuel, instead of Zry-4, of Japanese PWR plant whose upper limit of assembly discharged burnup ismore » 55 MWd/kgU. And we could confirm that the main aim of M-MDA was achieved by means of out-of-pile tests. In order to confirm improvement of corrosion resistance of M-MDA in the actual operation, irradiation test of M-MDA in the commercial reactor of Vandellos II is ongoing. The latest results of on-site examination after every end of cycle showed that oxide thickness of M-MDA-SR was much smaller than that of MDA at rod discharged burnup of approximately 60 MWd/kgU. The final irradiation cycle was completed on April 2007 and then we will obtain corrosion data of M-MDA over 70 MWd/kgU. M-MDA is a candidate alloy for advanced fuel under higher duty usage. (authors)« less

Demonstration of optimum fuel-to-moderator ratio in a PWR unit fuel cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feltus, M.A.; Pozsgai, C.

1992-01-01

Nuclear engineering students at The Pennsylvania State University develop scaled-down [[approx]350 MW(thermal)] pressurized water reactors (PWRs) using actual plants as references. The design criteria include maintaining the clad temperature below 2200[degree]F, fuel temperature below melting point, sufficient departure from nucleate boiling ratio (DNBR) margin, a beginning-of-life boron concentration that yields a negative moderator temperature coefficient, an adequate cycle power production (330 effective full-power days), and a batch loading scheme that is economical. The design project allows for many degrees of freedom (e.g., assembly number, pitch and height and batch enrichments) so that each student's result is unique. The iterative naturemore » of the design process is stressed in the course. The LEOPARD code is used for the unit cell depletion, critical boron, and equilibrium xenon calculations. Radial two-group diffusion equations are solved with the TWIDDLE-DEE code. The steady-state ZEBRA thermal-hydraulics program is used for calculating DNBR. The unit fuel cell pin radius and pitch (fuel-to-moerator ratio) for the scaled-down design, however, was set equal to the already optimized ratio for the reference PWR. This paper describes an honors project that shows how the optimum fuel-to-moderator ratio is found for a unit fuel cell shown in terms of neutron economics. This exercise illustrates the impact of fuel-to-moderator variations on fuel utilization factor and the effect of assuming space and energy separability.« less

Analytical methods in the high conversion reactor core design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeggel, W.; Oldekop, W.; Axmann, J.K.

High conversion reactor (HCR) design methods have been used at the Technical University of Braunschweig (TUBS) with the technological support of Kraftwerk Union (KWU). The present state and objectives of this cooperation between KWU and TUBS in the field of HCRs have been described using existing design models and current activities aimed at further development and validation of the codes. The hard physical and thermal-hydraulic boundary conditions of pressurized water reactor (PWR) cores with a high degree of fuel utilization result from the tight packing of the HCR fuel rods and the high fissionable plutonium content of the fuel. Inmore » terms of design, the problem will be solved with rod bundles whose fuel rods are adjusted by helical spacers to the proposed small rod pitches. These HCR properties require novel computational models for neutron physics, thermal hydraulics, and fuel rod design. By means of a survey of the codes, the analytical procedure for present-day HCR core design is presented. The design programs are currently under intensive development, as design tools with a solid, scientific foundation and with essential parameters that are widely valid and are required for a promising optimization of the HCR core. Design results and a survey of future HCR development are given. In this connection, the reoptimization of the PWR core in the direction of an HCR is considered a fascinating scientific task, with respect to both economic and safety aspects.« less

Automatic treatment of the variance estimation bias in TRIPOLI-4 criticality calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dumonteil, E.; Malvagi, F.

2012-07-01

The central limit (CLT) theorem States conditions under which the mean of a sufficiently large number of independent random variables, each with finite mean and variance, will be approximately normally distributed. The use of Monte Carlo transport codes, such as Tripoli4, relies on those conditions. While these are verified in protection applications (the cycles provide independent measurements of fluxes and related quantities), the hypothesis of independent estimates/cycles is broken in criticality mode. Indeed the power iteration technique used in this mode couples a generation to its progeny. Often, after what is called 'source convergence' this coupling almost disappears (the solutionmore » is closed to equilibrium) but for loosely coupled systems, such as for PWR or large nuclear cores, the equilibrium is never found, or at least may take time to reach, and the variance estimation such as allowed by the CLT is under-evaluated. In this paper we first propose, by the mean of two different methods, to evaluate the typical correlation length, as measured in cycles number, and then use this information to diagnose correlation problems and to provide an improved variance estimation. Those two methods are based on Fourier spectral decomposition and on the lag k autocorrelation calculation. A theoretical modeling of the autocorrelation function, based on Gauss-Markov stochastic processes, will also be presented. Tests will be performed with Tripoli4 on a PWR pin cell. (authors)« less

DEVELOPMENT OF A SAMPLING PROCEDURE FOR LARGE NITROGEN- AND SULFUR-BEARING AEROSOLS

EPA Science Inventory

A single-stage impactor was modified to utilize a removable TFE impaction surface mounted on the end of an annular denuder. hen used with a polycarbonate filter coated with silicone oil, its cut point was 2.5 um and bounce was <1% for 8-um particles. ignificant bounce occurred wi...

First Results from the ISO-IRAS Faint Galaxy Survey

NASA Technical Reports Server (NTRS)

Wolstencroft, R. D.; Wehrle, A. E.; Levine, D. A.

1997-01-01

We present the first result from the ISO-IRAS Faint Galaxy Survey (IIFGS), a program designed to obtain ISO observations of the most distant and luminous galaxies in the IRAS Faint Source Survey by filling short gaps in the ISO observing schedule with pairs of 12um ISOCAM AND 90um ISOPHOT observation.

Students' Perceptions of Blackboard and Moodle in a Portuguese University

ERIC Educational Resources Information Center

Carvalho, Ana; Areal, Nelson; Silva, Joaquim

2011-01-01

The use of learning management systems (LMS) has grown considerably in universities around the world. The University of Minho (UM) has pioneered in this area in Portugal, adopting Blackboard as its official LMS. Moodle is also used in UM in scattered initiatives, allowing for interesting comparisons. Previous studies comparing Blackboard and…

Use of "um" in the Deceptive Speech of a Convicted Murderer

ERIC Educational Resources Information Center

Villar, Gina; Arciuli, Joanne; Mallard, David

2012-01-01

Previous studies have demonstrated a link between language behaviors and deception; however, questions remain about the role of specific linguistic cues, especially in real-life high-stakes lies. This study investigated use of the so-called filler, "um," in externally verifiable truthful versus deceptive speech of a convicted murderer. The data…

Closing the Math Achievement Gap: Institutions Find Success with MyMathLab

ERIC Educational Resources Information Center

Stewart, Pearl

2012-01-01

Institutions find success with Pearson Education's MyMathLab. The Department of Mathematical Sciences at the University of Memphis (UM) reported a narrowing of the achievement gap between Black and White students. According to the study conducted by UM professors and titled "The Effectiveness of Blended Instruction in Postsecondary General…

DETERMINING COARSE PARTICULATE MATTER CONCENTRATIONS: A PERFORMANCE EVALUATION OF CANDIDATE METHODOLOGIES UNDER WINTERTIME CONDITIONS

EPA Science Inventory

The main objective of this study is to evaluate the performance of sampling methods for potential use as a Federal Reference Method (FRM) capable of providing an estimate of coarse particle (PMc: particulate matter with an aerodynamic diameter between 2.5 um and 10 um) mass con...

TRIBUTYLTIN AND DEXAMETHASONE INDUCE APOPTOSIS IN RAT THYMOCYTES BY MUTUALLY ANTAGONISTIC MECHANISMS

EPA Science Inventory

We observed that rat thymocyte cultures exposed to 1.O'- 2. 5 uM tri-n-butyltin methoxide (TBT) exhibiteda rapid time- and concentration-dependent induction of apoptosis, with > 85% of cells exhibiting reduced DNAcontent within 1 hr after ensure to 2.0 - 2,5 uM TBT. Moreover, wit...

Nonlinear THz Plamonic Disk Resonators

NASA Astrophysics Data System (ADS)

Seren, Huseyin; Zhang, Jingdi; Keiser, George; Maddox, Scott; Fan, Kebin; Cao, Lingyue; Bank, Seth; Zhang, Xin; Averitt, Richard

2013-03-01

Particle surface plasmons (PPSs) at visible wavelengths continue to be actively investigated with the goal of nanoscale control of light. In contrast, terahertz (THz) surface plasmon experiments are at a nascent stage of investigation. Doped semiconductors with proper carrier density and mobility support THz PSPs. One approach is to utilize thick doped films etched into subwavelength disks. Given the ease of tuning the semiconductor carrier density, THz PSPs are tunable and exhibit interesting nonlinear THz plasmonic effects. We created THz PSP structures using MBE grown 2um thick InAs films with a doping concentration of 1e17cm-3 on 500um thick semi-insulating GaAs substrate. We patterned 40um diameter disks with a 60um period by reactive ion etching. Our THz time-domain measurements reveal a resonance at 1.1THz which agrees well with simulation results using a Drude model. A nonlinear response occurs at high THz electric field strengths (>50kV/cm). In particular, we observed a redshift and quenching of the resonance due to impact ionization which resulted in changes in the carrier density and effective mass due to inter-valley scattering.

Cartilage ablation studies using mid-IR free electron laser

NASA Astrophysics Data System (ADS)

Youn, Jong-In; Peavy, George M.; Venugopalan, Vasan

2005-04-01

The ablation rate of articular cartilage and fibrocartilage (meniscus), were quantified to examine wavelength and tissue-composition dependence of ablation efficiency for selected mid-infrared wavelengths. The wavelengths tested were 2.9 um (water dominant absorption), 6.1 (protein and water absorption) and 6.45 um (protein dominant absorption) generated by the Free Electron Laser (FEL) at Vanderbilt University. The measurement of tissue mass removal using a microbalance during laser ablation was conducted to determine the ablation rates of cartilage. The technique can be accurate over methods such as profilometer and histology sectioning where tissue surface and the crater morphology may be affected by tissue processing. The ablation efficiency was found to be dependent upon the wavelength. Both articular cartilage and meniscus (fibrocartilage) ablations at 6.1 um were more efficient than those at the other wavelengths evaluated. We observed the lowest ablation efficiency of both types of cartilage with the 6.45 um wavelength, possibly due to the reduction in water absorption at this wavelength in comparison to the other wavelengths that were evaluated.

VizieR Online Data Catalog: Spitzer observations of Taurus members (Luhman+, 2010)

NASA Astrophysics Data System (ADS)

Luhman, K. L.; Allen, P. R.; Espaillat, C.; Hartmann, L.; Calvet, N.

2016-03-01

For our census of the disk population in Taurus, we use images at 3.6, 4.5, 5.8, and 8.0um obtained with Spitzer's Infrared Array Camera (IRAC) and images at 24um obtained with the Multiband Imaging Photometer for Spitzer (MIPS). The cameras produced images with FWHM=1.6"-1.9" from 3.6 to 8.0um and FWHM=5.9" at 24um. The available data were obtained through Guaranteed Time Observations for PID = 6, 36, 37 (G. Fazio), 53 (G. Rieke), 94 (C. Lawrence), 30540 (G. Fazio, J. Houck), and 40302 (J. Houck), Director's Discretionary Time for PID = 462 (L. Rebull), Legacy programs for PID = 139, 173 (N. Evans), and 30816 (D. Padgett), and General Observer programs for PID = 3584 (D. Padgett), 20302 (P. Andre), 20386 (P. Myers), 20762 (J. Swift), 30384 (T. Bourke), 40844 (C. McCabe), and 50584 (D. Padgett). The IRAC and MIPS observations were performed through 180 and 137 Astronomical Observation Requests (AORs), respectively. The characteristics of the resulting images are summarized in Tables 1 and 2. (6 data files).

Cascaded Ga1-xAlxAs/GaAs solar cell with graded i-region

NASA Astrophysics Data System (ADS)

Mil'shtein, Sam; Halilov, Samed

2018-02-01

In current study we designed p-i-n junction with extended intrinsic layer, where linearly graded Alx Ga1-x As presents variable energy gap so needed for effective harvesting of sun radiation. The design realization involves two regions of compositional structure in the stacking direction. The top AlxGa1-xAs layer of 1 um total thickness has stoichiometric structure x=0.3-0.2d, where depth d runs from 0 to 1 um, topmost 200 nm of which is Be-doped. Bottom AlxGa1-xAs layer of 3 um total thickness has a variable composition of x=0.133-0.033d, d runs from 1 to 4 um, the very bottom of which with 10 nm thickness is Si-doped. On the top surface, there is a 50 nm layer of p+ doped GaAs as a spacer for growing AuGe/Ni anode electrode of 20% surface area, the bottom is coated with AuGe/Ni cathode electrode. The designed cell demonstrates 89% fill factor and 30% conversion efficiency without anti-reflection coating.

Removal of sudan dyes from water with C18-functional ultrafine magnetic silica nanoparticles.

PubMed

Jiang, Chunzhu; Sun, Ying; Yu, Xi; Zhang, Lei; Sun, Xiumin; Gao, Yan; Zhang, Hanqi; Song, Daqian

2012-01-30

In this study, the new C(18)-functionalized ultrafine magnetic silica nanoparticles (C(18)-UMS NPs) were successfully synthesized and applied for extraction of sudan dyes in water samples based on the magnetic solid-phase extraction (MSPE). The extraction and concentration were carried out in one step by blending C(18)-UMS NPs and water samples. The sudan dyes adsorbed C(18)-UMS NPs were isolated from the matrix easily with an external magnetic field. After desorption the quantitation of sudan dyes was done by ultra fast liquid chromatography (UFLC). Satisfactory extraction recovery can be obtained with only 50 mg C(18)-UMS NPs. The effects of experimental parameters, including the amount of the nanoparticles, extraction time, pH value, desorption solvent, volume of desorption solvent and desorption time were investigated. The limits of detection for sudan I, II, III and IV were 0.066, 0.070, 0.12 and 0.12 ng mL(-1), respectively. Recoveries obtained by analyzing the six spiked water samples were between 68% and 103%. Copyright © 2011 Elsevier B.V. All rights reserved.

Optimization of microphysics in the Unified Model, using the Micro-genetic algorithm.

NASA Astrophysics Data System (ADS)

Jang, J.; Lee, Y.; Lee, H.; Lee, J.; Joo, S.

2016-12-01

This study focuses on parameter optimization of microphysics in the Unified Model (UM) using the Micro-genetic algorithm (Micro-GA). We need the optimization of microphysics in UM. Because, Microphysics in the Numerical Weather Prediction (NWP) model is important to Quantitative Precipitation Forecasting (QPF). The Micro-GA searches for optimal parameters on the basis of fitness function. The five parameters are chosen. The target parameters include x1, x2 related to raindrop size distribution, Cloud-rain correlation coefficient, Surface droplet number and Droplet taper height. The fitness function is based on the skill score that is BIAS and Critical Successive Index (CSI). An interface between UM and Micro-GA is developed and applied to three precipitation cases in Korea. The cases are (ⅰ) heavy rainfall in the Southern area because of typhoon NAKRI, (ⅱ) heavy rainfall in the Youngdong area, and (ⅲ) heavy rainfall in the Seoul metropolitan area. When the optimized result is compared to the control result (using the UM default value, CNTL), the optimized result leads to improvements in precipitation forecast, especially for heavy rainfall of the late forecast time. Also, we analyze the skill score of precipitation forecasts in terms of various thresholds of CNTL, Optimized result, and experiments on each optimized parameter for five parameters. Generally, the improvement is maximized when the five optimized parameters are used simultaneously. Therefore, this study demonstrates the ability to improve Korean precipitation forecasts by optimizing microphysics in UM.

Using a home blood pressure monitor: do accompanying instructional materials meet low literacy guidelines?

PubMed

Wallace, Lorraine S; Keenum, Amy J

2008-08-01

To evaluate the readability and related features of English language Quick Reference Guides (QRGs) and User Manuals (UMs) accompanying home blood pressure monitors (HBPMs). We evaluated QRGs and UMs for 22 HBPMs [arm (n=12); wrist (n=10)]. Using established criteria, we evaluated reading grade level, language availability, dimensions, text point size, use of illustrations, layout/formatting characteristics, and emphasis of key points of English-language patient instructions accompanying HBPMs. Readability was calculated using McLaughlin's Simplified Measure of Gobbledygoop. Items from the Suitability of Materials Assessment and User-Friendliness Tool were used to assess various layout features. Simplified Measure of Gobbledygoop scores of both QRGs (mean+/-SD=9.1+/-0.8) and UMs (9.3+/-0.8) ranged from 8th to 10th grade. QRGs and UMs presented steps in chronological order, used active voice throughout, avoided use of specialty fonts, focused on need to know, and used realistic illustrations. Seven sets of instructions included all seven key points related to proper HPBM use, whereas three sets of instructions included less than or equal to three key points (mean=4.8+/-1.9). Although most QRGs and UMs met at least some recommended low-literacy formatting guidelines, all instructional materials should be developed and tested to meet the needs of the patient population at large. Key points related to proper HBPM use should not only be included within these instructions, but highlighted to emphasize their importance.

Jupiter-Io Montage

NASA Technical Reports Server (NTRS)

2007-01-01

This is a montage of New Horizons images of Jupiter and its volcanic moon Io, taken during the spacecraft's Jupiter flyby in early 2007. The Jupiter image is an infrared color composite taken by the spacecraft's near-infrared imaging spectrometer, the Linear Etalon Imaging Spectral Array (LEISA) at 1:40 UT on Feb. 28, 2007. The infrared wavelengths used (red: 1.59 um, green: 1.94 um, blue: 1.85 um) highlight variations in the altitude of the Jovian cloud tops, with blue denoting high-altitude clouds and hazes, and red indicating deeper clouds. The prominent bluish-white oval is the Great Red Spot. The observation was made at a solar phase angle of 75 degrees but has been projected onto a crescent to remove distortion caused by Jupiter's rotation during the scan. The Io image, taken at 00:25 UT on March 1st 2007, is an approximately true-color composite taken by the panchromatic Long-Range Reconnaissance Imager (LORRI), with color information provided by the 0.5 um ('blue') and 0.9 um ('methane') channels of the Multispectral Visible Imaging Camera (MVIC). The image shows a major eruption in progress on Io's night side, at the northern volcano Tvashtar. Incandescent lava glows red beneath a 330-kilometer high volcanic plume, whose uppermost portions are illuminated by sunlight. The plume appears blue due to scattering of light by small particles in the plume

This montage appears on the cover of the Oct. 12, 2007, issue of Science magazine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenfeld, Daniel; Wang, Hailong; Rasch, Philip J.

Numerical simulations described in previous studies showed that adding cloud condensation nuclei to marine stratocumulus can prevent their breakup from closed into open cells. Additional analyses of the same simulations show that the suppression of rain is well described in terms of cloud drop effective radius (re). Rain is initiated when re near cloud top is around 12-14 um. Cloud water starts to get depleted when column-maximum rain intensity (Rmax) exceeds 0.1 mm h-1. This happens when cloud-top re reaches 14 um. Rmax is mostly less than 0.1 mm h-1 at re<14 um, regardless of the cloud water path, butmore » increases rapidly when re exceeds 14 um. This is in agreement with recent aircraft observations and theoretical observations in convective clouds so that the mechanism is not limited to describing marine stratocumulus. These results support the hypothesis that the onset of significant precipitation is determined by the number of nucleated cloud drops and the height (H) above cloud base within the cloud that is required for cloud drops to reach re of 14 um. In turn, this can explain the conditions for initiation of significant drizzle and opening of closed cells providing the basis for a simple parameterization for GCMs that unifies the representation of both precipitating and non-precipitating clouds as well as the transition between them. Furthermore, satellite global observations of cloud depth (from base to top), and cloud top re can be used to derive and validate this parameterization.« less

Busca de estruturas em grandes escalas em altos redshifts

NASA Astrophysics Data System (ADS)

Boris, N. V.; Sodré, L., Jr.; Cypriano, E.

2003-08-01

A busca por estruturas em grandes escalas (aglomerados de galáxias, por exemplo) é um ativo tópico de pesquisas hoje em dia, pois a detecção de um único aglomerado em altos redshifts pode por vínculos fortes sobre os modelos cosmológicos. Neste projeto estamos fazendo uma busca de estruturas distantes em campos contendo pares de quasares próximos entre si em z Â3 0.9. Os pares de quasares foram extraídos do catálogo de Véron-Cetty & Véron (2001) e estão sendo observados com os telescópios: 2,2m da University of Hawaii (UH), 2,5m do Observatório de Las Campanas e com o GEMINI. Apresentamos aqui a análise preliminar de um par de quasares observado nos filtros i'(7800 Å) e z'(9500 Å) com o GEMINI. A cor (i'-z') mostrou-se útil para detectar objetos "early-type" em redshifts menores que 1.1. No estudo do par 131046+0006/J131055+0008, com redshift ~ 0.9, o uso deste método possibilitou a detecção de sete objetos candidatos a galáxias "early-type". Num mapa da distribuição projetada dos objetos para 22 < i' < 25 observou-se que estas galáxias estão localizadas próximas a um dos quasares e há indícios de que estejam aglomeradas dentro de um área de ~ 6 arcmin2. Se esse for o caso, estes objetos seriam membros de uma estrutura em grande escala. Um outro argumento em favor dessa hipótese é que eles obedecem uma relação do tipo Kormendy (raio equivalente X brilho superficial dentro desse raio), como a apresentada pelas galáxias elípticas em z = 0.

Variation in aluminum, iron, and particle concentrations in oxic groundwater samples collected by use of tangential-flow ultrafiltration with low-flow sampling

NASA Astrophysics Data System (ADS)

Szabo, Zoltan; Oden, Jeannette H.; Gibs, Jacob; Rice, Donald E.; Ding, Yuan

2002-02-01

Particulates that move with ground water and those that are artificially mobilized during well purging could be incorporated into water samples during collection and could cause trace-element concentrations to vary in unfiltered samples, and possibly in filtered samples (typically 0.45-um (micron) pore size) as well, depending on the particle-size fractions present. Therefore, measured concentrations may not be representative of those in the aquifer. Ground water may contain particles of various sizes and shapes that are broadly classified as colloids, which do not settle from water, and particulates, which do. In order to investigate variations in trace-element concentrations in ground-water samples as a function of particle concentrations and particle-size fractions, the U.S. Geological Survey, in cooperation with the U.S. Air Force, collected samples from five wells completed in the unconfined, oxic Kirkwood-Cohansey aquifer system of the New Jersey Coastal Plain. Samples were collected by purging with a portable pump at low flow (0.2-0.5 liters per minute and minimal drawdown, ideally less than 0.5 foot). Unfiltered samples were collected in the following sequence: (1) within the first few minutes of pumping, (2) after initial turbidity declined and about one to two casing volumes of water had been purged, and (3) after turbidity values had stabilized at less than 1 to 5 Nephelometric Turbidity Units. Filtered samples were split concurrently through (1) a 0.45-um pore size capsule filter, (2) a 0.45-um pore size capsule filter and a 0.0029-um pore size tangential-flow filter in sequence, and (3), in selected cases, a 0.45-um and a 0.05-um pore size capsule filter in sequence. Filtered samples were collected concurrently with the unfiltered sample that was collected when turbidity values stabilized. Quality-assurance samples consisted of sequential duplicates (about 25 percent) and equipment blanks. Concentrations of particles were determined by light scattering.

Impact of Tile Drainage on the Distribution of Concentration and Age of Inorganic Soil Nitrogen.

NASA Astrophysics Data System (ADS)

Woo, D.; Kumar, P.

2017-12-01

Extensive network of tile drainage network across the Midwestern United States, northern Europe and other regions of the world have enhanced agricultural productivity. Because of its impact on sub-surface flow patterns and moisture and temperature dynamics, it controls the nitrogen cycle in agricultural systems, and its influence on nitrogen dynamics plays a key role in determining the short- and long-term evolution of soil inorganic nitrogen concentration and age. The spatial mapping of nitrogen concentration and age under tile-drained fields has, therefore, the potential to open up novel solution to the vexing challenge of reducing environmental impacts while at the same time maintaining agricultural productivity. The objective of this study is to explore the impacts of tile drains on the age dynamics of nitrate, immobile ammonium, mobile ammonia/um, and non-reactive tracer (such as chloride) by implementing two mobile interacting pore domains to capture matrix and preferential flow paths in a coupled ecohydrology and biogeochemistry model, Dhara. We applied this model to an agricultural farm supporting a corn-soybean rotation in the Midwestern United States. It should be expected that the installation of tile drains decrease the age of soil nutrient due to nutrient losses through tile drainage. However, an increase in the age of mobile ammonia/um is observed in contrast to the cases for nitrate, immobile ammonium, and non-reactive tracer. These results arise because the depletion of mobile ammonia/um due to tile drainage causes a high mobility flux from immobile ammonium to mobile ammonia/um, which also carries a considerable amount of relatively old age of immobile ammonium to mobile ammonia/um. In addition, the ages of nitrate and mobile ammonia/um in tile drainage range from 1 to 3 years, and less than a year, respectively, implying that not considering age transformations between nitrogen species would result in substantial underestimation of nitrogen ages, possibly leading to an erroneous conclusion.

Evaluation of Laser Stabilization and Imaging Systems for LCLS-II - Final Paper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barry, Matthew

2015-08-20

By combining the top performing commercial laser beam stabilization system with the most ideal optical imaging configuration, the beamline for the Linear Accelerator Coherent Light Source II (LCLS-II) will deliver the highest quality and most stable beam to the cathode. To determine the optimal combination, LCLS-II beamline conditions were replicated and the systems tested with a He-Ne laser. The Guidestar-II and MRC active laser beam stabilization systems were evaluated for their ideal positioning and stability. Both a two and four lens optical imaging configuration was then evaluated for beam imaging quality, magnification properties, and natural stability. In their best performancesmore » when tested over fifteen hours, Guidestar-II kept the beam stable over approximately 70-110um while the MRC system kept it stable over approximately 90-100um. During short periods of time, Guidestar-II kept the beam stable between 10-20um, but was more susceptible to drift over time, while the MRC system maintained the beam between 30-50um with less overall drift. The best optical imaging configuration proved to be a four lens system that images to the iris located in the cathode room and from there, imaged to the cathode. The magnification from the iris to the cathode was 2:1, within an acceptable tolerance to the expected 2.1:1 magnification. The two lens configuration was slightly more stable in small periods of time (less than 10 minutes) without the assistance of a stability system, approximately 55um compared to approximately 70um, but the four lens configurations beam image had a significantly flatter intensity distribution compared to the two lens configuration which had a Gaussian distribution. A final test still needs to be run with both stability systems running at the same time through the four lens system. With this data, the optimal laser beam stabilization system can be determined for the beamline of LCLS-II.« less

Ultrasonic location system =

NASA Astrophysics Data System (ADS)

Albuquerque, Daniel Filipe

Esta tese apresenta um sistema de localizacao baseado exclusivamente em ultrassons, nao necessitando de recorrer a qualquer outra tecnologia. Este sistema de localizacao foi concebido para poder operar em ambientes onde qualquer outra tecnologia nao pode ser utilizada ou o seu uso esta condicionado, como sao exemplo aplicacoes subaquaticas ou ambientes hospitalares. O sistema de localizacao proposto faz uso de uma rede de farois fixos permitindo que estacoes moveis se localizem. Devido a necessidade de transmissao de dados e medicao de distancias foi desenvolvido um pulso de ultrassons robusto a ecos que permite realizar ambas as tarefas com sucesso. O sistema de localizacao permite que as estacoes moveis se localizem escutando apenas a informacao em pulsos de ultrassons enviados pelos farois usando para tal um algoritmo baseado em diferencas de tempo de chegada. Desta forma a privacidade dos utilizadores e garantida e o sistema torna-se completamente independente do numero de utilizadores. Por forma a facilitar a implementacao da rede de farois apenas sera necessario determinar manualmente a posicao de alguns dos farois, designados por farois ancora. Estes irao permitir que os restantes farois, completamente autonomos, se possam localizar atraves de um algoritmo iterativo de localizacao baseado na minimizacao de uma funcao de custo. Para que este sistema possa funcionar como previsto sera necessario que os farois possam sincronizar os seus relogios e medir a distancia entre eles. Para tal, esta tese propoe um protocolo de sincronizacao de relogio que permite tambem obter as medidas de distancia entre os farois trocando somente tres mensagens de ultrassons. Adicionalmente, o sistema de localizacao permite que farois danificados possam ser substituidos sem comprometer a operabilidade da rede reduzindo a complexidade na manutencao. Para alem do mencionado, foi igualmente implementado um simulador de ultrassons para ambientes fechados, o qual provou ser bastante preciso e uma ferramenta de elevado valor para simular o comportamento do sistema de localizacao sobre condicoes controladas.

Scoping Study Investigating PWR Instrumentation during a Severe Accident Scenario

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rempe, J. L.; Knudson, D. L.; Lutz, R. J.

The accidents at the Three Mile Island Unit 2 (TMI-2) and Fukushima Daiichi Units 1, 2, and 3 nuclear power plants demonstrate the critical importance of accurate, relevant, and timely information on the status of reactor systems during a severe accident. These events also highlight the critical importance of understanding and focusing on the key elements of system status information in an environment where operators may be overwhelmed with superfluous and sometimes conflicting data. While progress in these areas has been made since TMI-2, the events at Fukushima suggests that there may still be a potential need to ensure thatmore » critical plant information is available to plant operators. Recognizing the significant technical and economic challenges associated with plant modifications, it is important to focus on instrumentation that can address these information critical needs. As part of a program initiated by the Department of Energy, Office of Nuclear Energy (DOE-NE), a scoping effort was initiated to assess critical information needs identified for severe accident management and mitigation in commercial Light Water Reactors (LWRs), to quantify the environment instruments monitoring this data would have to survive, and to identify gaps where predicted environments exceed instrumentation qualification envelop (QE) limits. Results from the Pressurized Water Reactor (PWR) scoping evaluations are documented in this report. The PWR evaluations were limited in this scoping evaluation to quantifying the environmental conditions for an unmitigated Short-Term Station BlackOut (STSBO) sequence in one unit at the Surry nuclear power station. Results were obtained using the MELCOR models developed for the US Nuclear Regulatory Commission (NRC)-sponsored State of the Art Consequence Assessment (SOARCA) program project. Results from this scoping evaluation indicate that some instrumentation identified to provide critical information would be exposed to conditions that significantly exceeded QE limits for extended time periods for the low frequency STSBO sequence evaluated in this study. It is recognized that the core damage frequency (CDF) of the sequence evaluated in this scoping effort would be considerably lower if evaluations considered new FLEX equipment being installed by industry. Nevertheless, because of uncertainties in instrumentation response when exposed to conditions beyond QE limits and alternate challenges associated with different sequences that may impact sensor performance, it is recommended that additional evaluations of instrumentation performance be completed to provide confidence that operators have access to accurate, relevant, and timely information on the status of reactor systems for a broad range of challenges associated with risk important severe accident sequences.« less

High-temperature compatibility between liquid metal as PWR fuel gap filler and stainless steel and high-density concrete

NASA Astrophysics Data System (ADS)

Wongsawaeng, Doonyapong; Jumpee, Chayanit; Jitpukdee, Manit

2014-08-01

In conventional nuclear fuel rods for light-water reactors, a helium-filled as-fabricated gap between the fuel and the cladding inner surface accommodates fuel swelling and cladding creep down. Because helium exhibits a very low thermal conductivity, it results in a large temperature rise in the gap. Liquid metal (LM; 1/3 weight portion each of lead, tin, and bismuth) has been proposed to be a gap filler because of its high thermal conductivity (∼100 times that of He), low melting point (∼100 °C), and lack of chemical reactivity with UO2 and water. With the presence of LM, the temperature drop across the gap is virtually eliminated and the fuel is operated at a lower temperature at the same power output, resulting in safer fuel, delayed fission gas release and prevention of massive secondary hydriding. During normal reactor operation, should an LM-bonded fuel rod failure occurs resulting in a discharge of liquid metal into the bottom of the reactor pressure vessel, it should not corrode stainless steel. An experiment was conducted to confirm that at 315 °C, LM in contact with 304 stainless steel in the PWR water chemistry environment for up to 30 days resulted in no observable corrosion. Moreover, during a hypothetical core-melt accident assuming that the liquid metal with elevated temperature between 1000 and 1600 °C is spread on a high-density concrete basement of the power plant, a small-scale experiment was performed to demonstrate that the LM-concrete interaction at 1000 °C for as long as 12 h resulted in no penetration. At 1200 °C for 5 h, the LM penetrated a distance of ∼1.3 cm, but the penetration appeared to stop. At 1400 °C the penetration rate was ∼0.7 cm/h. At 1600 °C, the penetration rate was ∼17 cm/h. No corrosion based on chemical reactions with high-density concrete occurred, and, hence, the only physical interaction between high-temperature LM and high-density concrete was from tiny cracks generated from thermal stress. Moreover, for as high as 1600 °C, the non-reactive LM was experimentally confirmed not to show any chemical reaction with air or moisture in the air. This experimental work confirmed the excellent compatibility behaviors between the LM as a PWR fuel gap filler and stainless steel and high-density concrete in the high-temperature regime.

Development and Application of Laser Peening System for PWR Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masaki Yoda; Itaru Chida; Satoshi Okada

2006-07-01

Laser peening is a process to improve residual stress from tensile to compressive in surface layer of materials by irradiating high-power laser pulses on the material in water. Toshiba has developed a laser peening system composed of Q-switched Nd:YAG laser oscillators, laser delivery equipment and underwater remote handling equipment. We have applied the system for Japanese operating BWR power plants as a preventive maintenance measure for stress corrosion cracking (SCC) on reactor internals like core shrouds or control rod drive (CRD) penetrations since 1999. As for PWRs, alloy 600 or 182 can be susceptible to primary water stress corrosion crackingmore » (PWSCC), and some cracks or leakages caused by the PWSCC have been discovered on penetrations of reactor vessel heads (RVHs), reactor bottom-mounted instrumentation (BMI) nozzles, and others. Taking measures to meet the unconformity of the RVH penetrations, RVHs themselves have been replaced in many PWRs. On the other hand, it's too time-consuming and expensive to replace BMI nozzles, therefore, any other convenient and less expensive measures are required instead of the replacement. In Toshiba, we carried out various tests for laser-peened nickel base alloys and confirmed the effectiveness of laser peening as a preventive maintenance measure for PWSCC. We have developed a laser peening system for PWRs as well after the one for BWRs, and applied it for BMI nozzles, core deluge line nozzles and primary water inlet nozzles of Ikata Unit 1 and 2 of Shikoku Electric Power Company since 2004, which are Japanese operating PWR power plants. In this system, laser oscillators and control devices were packed into two containers placed on the operating floor inside the reactor containment vessel. Laser pulses were delivered through twin optical fibers and irradiated on two portions in parallel to reduce operation time. For BMI nozzles, we developed a tiny irradiation head for small tubes and we peened the inner surface around J-groove welds after laser ultrasonic testing (LUT) as the remote inspection, and we peened the outer surface and the weld for Ikata Unit 2 supplementary. For core deluge line nozzles and primary water inlet nozzles, we peened the inner surface of the dissimilar metal welding, which is of nickel base alloy, joining a safe end and a low alloy metal nozzle. In this paper, the development and the actual application of the laser peening system for PWR power plants will be described. (authors)« less

Development and Testing of Neutron Cross Section Covariance Data for SCALE 6.2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marshall, William BJ J; Williams, Mark L; Wiarda, Dorothea

2015-01-01

Neutron cross-section covariance data are essential for many sensitivity/uncertainty and uncertainty quantification assessments performed both within the TSUNAMI suite and more broadly throughout the SCALE code system. The release of ENDF/B-VII.1 included a more complete set of neutron cross-section covariance data: these data form the basis for a new cross-section covariance library to be released in SCALE 6.2. A range of testing is conducted to investigate the properties of these covariance data and ensure that the data are reasonable. These tests include examination of the uncertainty in critical experiment benchmark model k eff values due to nuclear data uncertainties, asmore » well as similarity assessments of irradiated pressurized water reactor (PWR) and boiling water reactor (BWR) fuel with suites of critical experiments. The contents of the new covariance library, the testing performed, and the behavior of the new covariance data are described in this paper. The neutron cross-section covariances can be combined with a sensitivity data file generated using the TSUNAMI suite of codes within SCALE to determine the uncertainty in system k eff caused by nuclear data uncertainties. The Verified, Archived Library of Inputs and Data (VALID) maintained at Oak Ridge National Laboratory (ORNL) contains over 400 critical experiment benchmark models, and sensitivity data are generated for each of these models. The nuclear data uncertainty in k eff is generated for each experiment, and the resulting uncertainties are tabulated and compared to the differences in measured and calculated results. The magnitude of the uncertainty for categories of nuclides (such as actinides, fission products, and structural materials) is calculated for irradiated PWR and BWR fuel to quantify the effect of covariance library changes between the SCALE 6.1 and 6.2 libraries. One of the primary applications of sensitivity/uncertainty methods within SCALE is the assessment of similarities between benchmark experiments and safety applications. This is described by a c k value for each experiment with each application. Several studies have analyzed typical c k values for a range of critical experiments compared with hypothetical irradiated fuel applications. The c k value is sensitive to the cross-section covariance data because the contribution of each nuclide is influenced by its uncertainty; large uncertainties indicate more likely bias sources and are thus given more weight. Changes in c k values resulting from different covariance data can be used to examine and assess underlying data changes. These comparisons are performed for PWR and BWR fuel in storage and transportation systems.« less

Application of MELCOR Code to a French PWR 900 MWe Severe Accident Sequence and Evaluation of Models Performance Focusing on In-Vessel Thermal Hydraulic Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Rosa, Felice

2006-07-01

In the ambit of the Severe Accident Network of Excellence Project (SARNET), funded by the European Union, 6. FISA (Fission Safety) Programme, one of the main tasks is the development and validation of the European Accident Source Term Evaluation Code (ASTEC Code). One of the reference codes used to compare ASTEC results, coming from experimental and Reactor Plant applications, is MELCOR. ENEA is a SARNET member and also an ASTEC and MELCOR user. During the first 18 months of this project, we performed a series of MELCOR and ASTEC calculations referring to a French PWR 900 MWe and to themore » accident sequence of 'Loss of Steam Generator (SG) Feedwater' (known as H2 sequence in the French classification). H2 is an accident sequence substantially equivalent to a Station Blackout scenario, like a TMLB accident, with the only difference that in H2 sequence the scram is forced to occur with a delay of 28 seconds. The main events during the accident sequence are a loss of normal and auxiliary SG feedwater (0 s), followed by a scram when the water level in SG is equal or less than 0.7 m (after 28 seconds). There is also a main coolant pumps trip when {delta}Tsat < 10 deg. C, a total opening of the three relief valves when Tric (core maximal outlet temperature) is above 603 K (330 deg. C) and accumulators isolation when primary pressure goes below 1.5 MPa (15 bar). Among many other points, it is worth noting that this was the first time that a MELCOR 1.8.5 input deck was available for a French PWR 900. The main ENEA effort in this period was devoted to prepare the MELCOR input deck using the code version v.1.8.5 (build QZ Oct 2000 with the latest patch 185003 Oct 2001). The input deck, completely new, was prepared taking into account structure, data and same conditions as those found inside ASTEC input decks. The main goal of the work presented in this paper is to put in evidence where and when MELCOR provides good enough results and why, in some cases mainly referring to its specific models (candling, corium pool behaviour, etc.) they were less good. A future work will be the preparation of an input deck for the new MELCOR 1.8.6. and to perform a code-to-code comparison with ASTEC v1.2 rev. 1. (author)« less

Desenvolvimento das câmeras de raios-X duros do satélite MIRAX

NASA Astrophysics Data System (ADS)

Braga, J.; Rothschild, R.; Staubert, R.; Heise, J.; Remillard, R.; D'Amico, F.; Jablonski, F.; Mejía, J.; Carvalho, H.; Heindl, B.; Matteson, J.; Kendziorra, E.; Wilms, J.; in't Zand, J.; Kuulkers, E.

2003-08-01

O MIRAX (Monitor e Imageador de RAios-X) é um projeto de desenvolvimento de um pequeno satélite astronômico de raios-X (~200 kg, ~240 W). A estratégia básica da missão será observar continuamente (~9 meses por ano) a região central (~1000 graus2) do plano Galáctico e realizar estudos espectroscópicos de banda larga (2-200 keV) e alta sensibilidade de um grande conjunto de fontes através de imagens com resolução de ~6'. Isso proporcionará uma cobertura inédita do "espaço de descobertas" através da detecção, localização, identificação e estudo detalhado de fenômenos imprevisíveis, tais como transientes fracos de raios-X, novas rápidas de raios-X e bursts de raios gama, assim como o estudo de fontes com emissão persistente. Neste trabalho apresentamos o projeto das duas câmeras de raios-X duros (CXDs) do MIRAX, que irão operar na faixa de 10 a 200 keV. Cada CXD consistirá de um plano de detectores CZT (Cd0,9Zn0,1Te) de 0,5 mm de resolução espacial e 370 cm2 de área total, e de uma máscara codificada com elementos quadrados de 1,3 mm de lado e 0,5 cm de espessura. A máscara terá dimensões de 315 cm ´ 275 cm e será montada a 700 cm de distância dos detectores. Com essa configuração as CXDs terão 6' de resolução angular e, quando colocadas a um ângulo de 29° entre si, as duas câmeras propiciam um campo totalmente codificado de 39° ´ 6°12' e um campo total de 76° ´ 44°. Serão apresentadas simulações de observações da região do plano Galáctico com o conjunto formado pelas duas CXDs.

Transient deep-water oxygenation in the early Cambrian Nanhua Basin, South China

NASA Astrophysics Data System (ADS)

Cheng, Meng; Li, Chao; Zhou, Lian; Feng, LianJun; Algeo, Thomas J.; Zhang, FeiFei; Romaniello, Stephen; Jin, ChengSheng; Ling, HongFei; Jiang, ShaoYong

2017-08-01

Many late Neoproterozoic to early Cambrian fossils of multicellular eukaryotes, including those of benthic animals, are found preserved under anoxic and even euxinic bottom-water conditions, which is contradictory to the consensus that oxygen is essential to eukaryotes. To investigate this conundrum, we conducted an integrated study of iron speciation, redox-sensitive trace elements, and Mo isotopes (δ98Mo) on the black shale interval of the lower Cambrian Hetang Formation (∼535-521 Ma) at Lantian, South China, in which benthic sponge fossils are abundant in the lower member (LM) but absent in the upper member (UM). Iron speciation data point to uniformly anoxic-ferruginous conditions in the LM and euxinic conditions in the UM, whereas the trace-element and δ98Mo data show greater secular variation in redox conditions. The LM shows higher mean trace element concentrations (Mo: 108 ppm, U: 36 ppm, V: 791 ppm) and lower and more variable δ98Mo (+0.13 to +1.76‰) relative to the UM (Mo: 45 ppm, U: 18 ppm, V: 265 ppm, δ98Mo: +1.59 to +1.67‰), and ratios of redox-sensitive trace element concentrations to total organic carbon are significantly more variable and higher on average in the LM relative to the UM. The appearance of sponge fossils and lower δ98Mo values correlate strongly with gray (i.e., lighter-colored) layers in the LM. These patterns can best be interpreted as recording mainly euxinic conditions throughout deposition of the study units, with more intense background euxinia in the LM relative to the UM, but also with frequent transient oxygenation events in the LM that do not appear in the UM. The transient oxygenation events of the LM led to the initial colonization of the deep Nanhua Basin by sponges, and the termination of these events in the UM caused sponge faunas to disappear until a general rise in O2 levels later in the Cambrian permitted their return to deeper-water habitats. Our study also illustrates that multiple geochemical and paleobiological proxies exhibit different responses in 'poikiloredox' environments (i.e., characterized by small-scale spatial and high-frequency temporal variations), which can lead to apparent contradictions between metazoan fossil occurrences and their inferred watermass redox conditions.

A teoria da percolação aplicada às galáxias aneladas peculiares

NASA Astrophysics Data System (ADS)

Poppe, P. C. R.; Martin, V. A. F.; de Medeiros, N. G. F.; Faúndez-Abans, M.; Oliveira-Abans, M.

2003-08-01

Formulado no final da década de 50, o modelo de percolação concentra-se em descrever o meio poroso, que será visto neste trabalho como uma rede de canais aleatórios, por onde escoa um fluido determinístico. Se o número de canais for suficientemente grande, então eles estarão ligados e o meio se tornará permeável à passagem do fluido. Neste caso, dizemos que houve a percolação do fluido. Reformulando o modelo acima, podemos escrever um código particularmente adaptado para simulações em Galáxias, onde iremos supor que os canais formam um reticulado, e que cada sítio da rede representa um poro que será interpretado como uma região ativa de formação estelar. Para cada elo teremos um pequeno canal ligando dois sítios vizinhos, que poderá, após um tempo "t", induzir ou não a formação de uma região ativa no poro vizinho. Para simular a passagem desta região ativa através dos poros, diremos que um elo está aberto com probabilidade p e fechado com probabilidade 1-p. Dessa forma, passamos a imaginar configurações de elos abertos e fechados, onde cada configuração ocorre com uma certa probabilidade, dada por p|A|(1-p)|F|, onde |A| é o número de elos abertos e |F| o número de elos fechados da configuração. A expressão anterior só tem importância física se |A| e |F| forem ambos finitos, pois, caso contrário, a probabilidade de ocorrência de uma dada configuração será sempre nula. Neste trabalho, foram considerados dados cinemáticos publicados na literatura bem como aqueles obtidos pelos autores a partir de observações fotométricas realizadas no Observatório de Las Campanãs, em 1994, para a Galáxia Anelada Peculiar HRG 03401. Mostraremos que para certos valores de p, situados entre 0,5 e 0,6, os clusters assim formados irão simular, de maneira coerente, o referido objeto.

Análise dos Conceitos Astronômicos Apresentados por Professores de Algumas Escolas Estaduais Brasileiras

NASA Astrophysics Data System (ADS)

Voelzke, Marcos Rincon; Gonzaga, Edson Pereira

2011-12-01

A razão para o desenvolvimento deste trabalho baseia-se no fato de que muitos professores da Educação Básica (EB) não lidam com conceitos relacionados à astronomia, e quando o fazem eles simplesmente seguem livros didáticos que podem conter erros conceituais. Como é de conhecimento geral a astronomia é um dos conteúdos a serem ensinados na EB fazendo parte dos Parâmetros Curriculares Nacionais e das Propostas Curriculares do Estado de São Paulo, mas é um fato, que vários pesquisadores apontam, a existência de muitos problemas no ensino da astronomia. Com o propósito de minimizar algumas dessas deficiências foi realizado um trabalho de pesquisa com a utilização de questionários pré e pós pesquisa, para tanto foi desenvolvido um Curso de Extensão Universitária para professores da Diretoria de Ensino Regional (DE) que abrange Mauá, Ribeirão Pires e Rio Grande da Serra (no Estado de São Paulo) com os seguintes objetivos: levantar concepções alternativas; subsidiar os professores por meio de palestras, debates e workshops, e verificar o sucesso da aprendizagem após o curso, adotando-se como referência, para a análise dos resultados, os dicionários de Língua Portuguesa (FERREIRA, 2004) e Enciclopédico de Astronomia e Astronáutica (MOURĀO, 1995). Portanto, dezesseis questões foram aplicadas antes e após o curso, assim pode-se verificar após a pesquisa que 100,0% dos professores sabiam os nomes das fases da Lua, 97,0% entenderam que o Sistema Solar é composto por oito planetas, 78,1% foram capazes de explicar como ocorre um eclipse lunar, um eclipse solar e um solstício, 72,7% sabiam como explicar a ocorrência das estações do ano; 64,5% explicaram corretamente a ocorrência do equinócio, 89,7% foram capazes de definir adequadamente o termo cometa; 63,6% definiram asteróide, 54,5% meteoro, 58,1% galáxia, e 42,4% planeta. Os resultados obtidos indicam uma aprendizagem significativa por parte dos participantes.

Size Distribution and First Flush Effects of Mercury Containing Particles in Highway Runoff Water

NASA Astrophysics Data System (ADS)

Ferguson, K.; Green, P.

2007-12-01

Human and environmental health concerns have recently prompted many California water quality control boards to lower the Total Maximum Daily Loads (TMDL) of Mercury into their water systems. A size distribution study of mercury containing particles was conducted in order to begin to understand the possible sources of the contamination in highway storm water runoff. Four storms were studied from a monitoring site in the Los Angeles area near the crossing of highways 605 and 91. Storm water ran through an extended detention basin made of earthen material with a maximum water depth of 1.17m. Grab samples were collected manually starting at the beginning of the runoff, continuing at every fifteen minutes for the first hour, followed by a collection every hour after that for the duration of the storm. The particle sizes were separated into five size ranges (larger than 100um, 20-100um, 8-20um, 0.45-8um, and 0-0.45um) by sequential filtration. The samples were then acid digested for further analysis. Five standard Mercury solutions ranging from 5 to 100 parts per trillion were prepared in nitric acid immediately before analysis. Samples were analyzed for both the Hg-199 and the Hg-202 isotopes using an Agilent 7500i Inductively Coupled Plasma Mass Spectrometer. Substantial sub-micron concentrations of mercury were detected from all four storms, and in all five particle size ranges studied. The total amount of Mercury detected from each of the storms ranged from 8.5 to 35.5 pptr. Bursts of rain correlate well with increases of influent Hg concentration. Although a First Flush effect can be seen in the first storm, it is not as strong and/or not shown at all in the remaining three. The detention basin used at the site was shown to be an efficient BMP, reducing the amount of Hg in the effluent runoff as much as 30 pptr and down to as little as 2 pptr. The majority of Hg was found in either the 8-20um or the 0-0.45um particle size ranges. Mitigation of either portion will be challenging, but necessary to meet proposed 50 percent reductions.