BVRI Photometric Study of the High Mass Ratio, Detached, Pre-contact W UMa Binary GQ Cancri

NASA Astrophysics Data System (ADS)

Samec, R. G.; Olson, A.; Caton, D.; Faulkner, D. R.

2017-12-01

CCD BVRcIc light curves of GQ Cancri were observed in April 2013 using the SARA North 0.9-meter Telescope at Kitt Peak National Observatory in Arizona in remote mode. It is a high-amplitude (V 0.9 magnitude) K0±V type eclipsing binary (T1 5250 K) with a photometrically-determined mass ratio of M2 / M1 = 0.80. Its spectral color type classifies it as a pre-contact W UMa Binary (PCWB). The Wilson-Devinney Mode 2 solutions show that the system has a detached binary configuration with fill-outs of 94% and 98% for the primary and secondary component, respectively. As expected, the light curve is asymmetric due to spot activity. Three times of minimum light were calculated, for two primary eclipses and one secondary eclipse, from our present observations. In total, some 26 times of minimum light covering nearly 20 years of observation were used to determine linear and quadratic ephemerides. It is noted that the light curve solution remained in a detached state for every iteration of the computer runs. The components are very similar with a computed temperature difference of only 4 K, and the flux of the primary component accounts for 53±55% of the system's light in B, V, Rc, and Ic. A 12-degree radius high latitude white spot (faculae) was iterated on the primary component.

Observations and light curve solutions of a selection of middle-contact W UMa binaries

NASA Astrophysics Data System (ADS)

Kjurkchieva, Diana Petrova; Popov, Velimir Angelov; Lyubenova Vasileva, Doroteya; Petrov, Nikola Ivanov

2018-04-01

Photometric observations in Sloan g‧ and i‧ bands of W UMa binaries NSVS 4340949, T-Dra0–00959, GSC 03950–00707, NSVS 4665041, NSVS 4803568, MM Peg, MM Com and NSVS 4751449 are presented. The light curve solutions revealed that the components of each target are of G and K spectral types. The binaries of the sample have middle-contact configurations whose fillout factors are within the range 0.2–0.4. The only exception is NSVS 4751449 which is in deeper contact (fillout factor of 0.55). It precisely obeys the relation between mass ratio and fillout factor for deep, low mass ratio overcontact binaries. One of the eclipses of almost all targets (except MM Peg) is an occultation and their photometric mass ratios and solutions could be accepted with confidence. We found that the target components have almost equal temperatures but differ considerably in size and mass. The components of the partially-eclipsed MM Peg have close parameters. Our solutions reveal that NSVS 4340949, T-Dra0–00959, NSVS 4803568 and MM Com are of W subtype while GSC 03950–00707, NSVS 4665041, MM Peg and NSVS 4751449 are of A subtype. This subclassification is well-determined for all totally-eclipsed binaries. The targets confirm the trends in which W-subtype systems have smaller periods and lower temperatures than A subtype binaries.

Photometric investigation of a very short period W UMa-type binary - Does CE Leonis have a large superluminous area?

NASA Technical Reports Server (NTRS)

Samec, Ronald G.; Su, Wen; Terrell, Dirk; Hube, Douglas P.

1993-01-01

A complete photometric analysis of BVRI Johnson-Cousins photometry of the high northern latitude galactic variable, CE Leo is presented. These observations were taken at Kitt Peak National Observatory on May 31, 1989-June 7, 1989. Three new precise epochs of minimum light were determined and a linear and a quadratic ephemeris were computed from these and previous data covering 28 years of observation. The light curves reveal that the system undergoes a brief 20 min totality in the primary eclipse, indicating that CE Leo is a W UMa W-type binary. A systemic velocity of about -40 km/s was determined. Standard magnitudes were found and a simultaneous solution of the B, V, R, I light curves was computed using the new Wilson-Devinney synthetic light curve code which has the capability of automatically adjusting star spots. The solution indicates that the system consists of two early K-type dwarfs in marginal contact with a fill-out factor less than 3 percent. Evidence for the presence of a large (45 deg radius) superluminous area on the cooler component is given.

Photometric investigation of the totally eclipsing contact binary V12 in the intermediate-age open cluster NGC 7789

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qian, S.-B.; Wang, J.-J.; Liu, L.

2015-02-01

NGC 7789 is an intermediate-age open cluster with an age similar to the mean age of contact binary stars. V12 is a bright W UMa-type binary star with an orbital period of 0.3917 days. The first complete light curves of V12 in the V, R, and I bands are presented and analyzed with the Wilson–Devinney (W-D) method. The results show that V12 is an intermediate-contact binary (f=43.0(±2.2)%) with a mass ratio of 3.848, and it is a W-type contact binary where the less massive component is slightly hotter than the more massive one. The asymmetry of the light curves ismore » explained by the presence of a dark spot on the more massive component. The derived orbital inclination (i=83{sub .}{sup ∘}6) indicates that it is a totally eclipsing binary, which suggests that the determined parameters are reliable. The orbital period may show a long-term increase at a rate of P-dot =+2.48(±0.17)×10{sup −6} days yr{sup −1} that reveals a rapid mass transfer from the less massive component to the more massive one. However, more observations are needed to confirm this conclusion. The presence of an intermediate-contact binary in an intermediate-age open cluster may suggest that some contact binaries have a very short pre-contact timescale. The presence of a third body and/or stellar collision may help to shorten the pre-contact evolution.« less

First Photometric Investigation of the Neglected EW-type Binary System V502 Her

NASA Astrophysics Data System (ADS)

Zhao, Ergang; Qian, Shengbang; Liao, Wenping; He, Jiajia; Shi, Xiangdong; Zhang, Jia

2018-04-01

V502 Her is a neglected EW-type binary, which has been known for more than 60 years. The first multi-color CCD photometric light curve and spectroscopic observations of contact binary V502 Her was obtained. Based on the LAMOST data, its spectrum can be found to be F5. Together with solutions of light curves by using the Wilson-Devinney code, it infers that V502 Her is an A-type W UMa contact binary system with the mass ratio of q = 0.313 and the filling factor of f = 38.1%. According to all minimum times from the literature and our observations, the orbital period was analyzed and a long-term increase with a periodic change (P 3 = 26.8 years) was computed. The orbital period increase may be caused by the mass transfer from a less-massive component to the more massive one, which indicates that V502 Her is in the thermal relaxation oscillation (TRO) controller stage, while the light-travel time effect (LTTE) through the presence of a cool third body may lead to the periodic variation.

THE FIRST PHOTOMETRIC INVESTIGATION OF THE NEGLECTED W-UMa-TYPE BINARY STAR UZ CMi

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qian, S.-B.; Li, K.; Liao, W.-P.

2013-04-15

UZ CMi was a W-UMa-type binary star found more than 80 years ago. However, it has been neglected in photometric investigations. Here, the first complete light curves in the B, V, R, and I bands are presented and analyzed using the Wilson and Devinney method. It is discovered that UZ CMi is a contact binary (f = 38.4({+-} 2.3)%) with a mass ratio of 0.45. The derived orbital inclination (i = 87 Degree-Sign ) indicates that it is a total eclipsing binary, which suggests that the determined parameters are reliable. By using 17 new eclipse times together with those collectedmore » from the literature, we found that the general trend of the observed-calculated (O - C) curve shows an upward parabolic variation that corresponds to a long-term increase in the orbital period at a rate of P-dot = +4.1 x 10{sup -8} days yr{sup -1}. The continuous increase may be caused by a mass transfer from the less massive component to the more massive one. This suggests that UZ CMi is in the thermal relaxation oscillation controlled stage of the evolutionary scheme proposed by Qian. UZ CMi will oscillate around a critical mass ratio and the contact configuration cannot be broken. After the upward parabolic change was removed, the (O - C){sub 2} curve of the photoelectric and charge-coupled device data revealed a cyclic variation with a small amplitude of 0.0026 days and a period of 21.1 yr. The cyclic change was analyzed for the light-travel time effect via the presence of an extremely cool stellar companion.« less

VizieR Online Data Catalog: Photometric analysis of contact binaries (Lapasset+ 1996)

NASA Astrophysics Data System (ADS)

Lapasset, E.; Gomez, M.; Farinas, R.

1996-09-01

We present BV light-curve synthetic analyses of three short-period contact (W UMa) binaries: HY Pavonis (P=~0.35days), AW Virginis (P=~0.35days), and BP Velorum (P=~0.26days). Different possible configurations for wide range of the mass ratio were explored in each case making use of the Wilson-Devinney code. The photometric parameters of the systems were determined from the synthetic light-curve solutions that best fit the observations. AW Vir has two components of very similar temperatures and therefore the subtype (A or W) remains undetermined. HY Pav and BP Vel are best modeled by W-type configurations and the asymmetries in the light curves are reproduced by introducing cool spots on the more massive secondary components. Although BP Vel lies in the region of the open cluster Cr 173, its distance modulus, in principle, rules it out as a cluster member. (6 data files).

The minimum mass ratio of W Ursae Majoris binaries

NASA Technical Reports Server (NTRS)

Rasio, Frederic A.

1995-01-01

The minimum mass ratio for tidal stability of a contact binary containing two unevolved main-sequence stars is calculated to be q(sub min) approximately =0.09 in the case of a mostly radiative primary, and it is higher if an appreciable fraction of the mass lies in a convective envelope. At least one observed system, AW UMa, has a mass ratio just below this value (q = 0.075), implying that, if the system is stable, the primary must be slightly evolved and must have a very shallow convective envelope. Contact binaries with mass ratios significantly below that of AW UMa should not be observed, since they are tidally unstable and quickly merge into a single, rapidly rotating object, on a timescale approximately 10(exp 3)-10(exp 4) yr.

Study of neglected (near-)contact binaries using small telescopes

NASA Astrophysics Data System (ADS)

Zejda, Miloslav; Zhang, Jia; Qian, Shengbang; Zhu, Liying; Mikulášek, Zdeněk

2016-07-01

We present the first results of our new program aimed at relatively bright neglected (near-)contact binaries. The targets can be observed using small telescopes from several to several tens of centimeters in diameter. Light ephemeris determined by phenomenological modeling and physical parameters of the system obtained by Wilson-Devinney method are given for the first stars V373 Dra, OQ UMa from our program.

CCD photometric analysis of the W UMa-type binary V376 Andromeda

NASA Astrophysics Data System (ADS)

Çiçek, C.

2011-01-01

This study presents the absolute parameters of the contact binary system V376 And. CCD photometric observations were made at the Çanakkale Onsekiz Mart University Observatory in 2004. The instrumental magnitudes of all observed stars were converted into standard magnitudes. New BV light curves of the system were analysed using the Wilson-Devinney method supplemented with a Monte Carlo type algorithm. Since there are large asymmetries between maxima (i.e., O'Connell effect) in these light curves, two different models (one with a cool spot and one with a hot spot) were applied to the photometric data. The best fit, which was obtained with a large hot spot on the secondary component, gives V376 And as an A sub-type contact binary in poor thermal contact and a small value of the filling factor ( f ≈ 0.07). Combining the solutions of our light curves and Rucinski et al. (2001)'s radial velocity curves, the following absolute parameters of the components were determined: M1 = 2.44 ± 0.04 M ⊙, M2 = 0.74 ± 0.03 M ⊙, R1 = 2.60 ± 0.03 R ⊙, R2 = 1.51 ± 0.02 R ⊙, L1 = 40 ± 4 L ⊙ and L2 = 5 ± 1 L ⊙. We also discuss the evolution of the system, which appears to have an age of 1.6 Gyr. The distance to V376 And was calculated as 230 ± 20 pc from this analysis, taking into account interstellar extinction.

Photometric Analyses of the Short-Period Contact Binaries HY Pavonis, AW Virginis, and BP Velorum

NASA Astrophysics Data System (ADS)

Lapasset, Emilio; Gomez, Mercedes; Farinas, Raul

1996-04-01

We present BV light curve synthetic analyses of three short period contact (W UMa) binaries: HY Pavonis (P ~0.35 days), AW Virginis (P ~0.35 days), and BP Velorum (P ~0.26 days). Different possible configurations for a wide range of the mass ratio were explored in each case making use of the Wilson-Divinney code. The photometric parameters of the systems were determined from the synthetic light curve solutions that best fit the observations. AW Vir has two components of very similar temperatures and therefore the subtype (A or W) remains undetermined. HY Pav and BP Vel are best modeled by W-type configurations and the asymmetries in the light curves are reproduced by introducing cool spots on the more massive secondary components. Even when BP Vel lies in the region of the open cluster Cr 173, its distance modulus, in principle, rules it out as a cluster member. (SECTION: Stars)

Physical Parameters of Components in Close Binary Systems. V

NASA Astrophysics Data System (ADS)

Zola, S.; Kreiner, J. M.; Zakrzewski, B.; Kjurkchieva, D. P.; Marchev, D. V.; Baran, A.; Rucinski, S. M.; Ogloza, W.; Siwak, M.; Koziel, D.; Drozdz, M.; Pokrzywka, B.

2005-12-01

The paper presents combined spectroscopic and photometric orbital solutions for ten close binary systems: CN And, V776 Cas, FU Dra, UV Lyn, BB Peg, V592 Per, OU Ser, EQ Tau, HN UMa and HT Vir. The photometric data consist of new multicolor light curves, while the spectroscopy has been recently obtained within the radial velocity program at the David Dunlap Observatory (DDO). Absolute parameters of the components for these binary systems are derived. Our results confirm that CN And is not a contact system. Its configuration is semi-detached with the secondary component filling its Roche lobe. The configuration of nine other systems is contact. Three systems (V776 Cas, V592 Per and OU Ser) have high (44-77%) and six (FU Dra, UV Lyn, BB Peg, EQ Tau, HN UMa and HT Vir) low or intermediate (8-32%) fill-out factors. The absolute physical parameters are derived.

Variability in the Milky Way: Contact Binaries as Diagnostic Tools

NASA Astrophysics Data System (ADS)

de Grijs, R.; Chen, X.; Deng, L.

2017-07-01

We used the 50 cm Binocular Network (50BiN) telescope at Delingha Station (Qinghai Province) of Purple Mountain Observatory (Chinese Academy of Sciences) to obtain simultaneous V- and R-band observations of the old open cluster NGC 188. Our aim was a search for populations of variable stars. We derived light-curve solutions for six W Ursae Majoris (W UMa) eclipsing-binary systems and estimated their orbital parameters. The resulting distance to the W UMas is independent of the physical characteristics of the host cluster. We next determined the current best period-luminosity relations for contact binaries (CBs; scatter σ<0.10 mag). We conclude that CBs can be used as distance tracers with better than 5% uncertainty. We apply our new relations to the 102 CBs in the Large Magellanic Cloud, which yields a distance modulus of (m-M)V,0=18.41±0.20 mag.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Y.-G.; Dai, H.-F.; Zhang, X.-B.

We present new photometry for the eclipsing binary V1241 Tau, which was obtained on six nights between 2011 December and 2012 January using the 85 cm telescope at the Xinglong station of the National Astronomical Observatories of China. By using the updated Wilson-Devinney code, photometric models with third lights were deduced from two sets of light curves. The result implies that V1241 Tau is an Algol-type near-contact binary (NCB), whose mass ratio and filling-out of the primary are q = 0.545 ({+-} 0.003) and f{sub 1} = 82.4% ({+-} 0.2%), respectively. Based on all available times of minimum light spanningmore » over 80 yr, the O - C curve of V1241 Tau appears to show a quasi-sinusoidal oscillation, i.e., a light-time orbit. The modulated period and amplitude are P{sub mod} = 47.4 ({+-} 1.7) yr and A = 0.0087 ({+-} 0.0005) days, respectively. This kind of period variation may be more likely attributed to the light-time effect via a presence of an unseen third body. From an analysis of 23 Algol-type NCBs with EB-type light curves, we determine that the fill-out for the primary f{sub 1} will increase as the orbital period P decreases. With angular momentum loss, the orbit of the binary will shrink, which causes f{sub 1} to increase. The primary component finally fills its Roche lobe, and the binary evolves into contact configuration. Therefore, this kind of Algol-type NCB with EB-type light curves, such as V1241 Tau, may be a progenitor of the A-type W UMa binary.« less

The evolution of the lithium abundances of solar-type stars. II - The Ursa Major Group

NASA Technical Reports Server (NTRS)

Soderblom, David R.; Pilachowski, Catherine A.; Fedele, Stephen B.; Jones, Burton F.

1993-01-01

We draw upon a recent study of the membership of the Ursa Major Group (UMaG) to examine lithium among 0.3 Gyr old solar-type stars. For most G and K dwarfs, Li confirms the conclusions about membership in UMaG reached on the basis of kinematics and chromospheric activity. G and K dwarfs in UMaG have less Li than comparable stars in the Pleiades. This indicates that G and K dwarfs undergo Li depletion while they are on the main sequence, in addition to any pre-main-sequence depletion they may have experienced. Moreover, the Li abundances of the Pleiades K dwarfs cannot be attributed to main-sequence depletion alone, demonstrating that pre-main-sequence depletion of Li also takes place. The sun's Li abundance implies that the main-sequence mechanism becomes less effective with age. The hottest stars in UMaG have Li abundances like those of hot stars in the Pleiades and Hyades and in T Tauris, and the two genuine UMaG members with temperatures near Boesgaard's Li chasm have Li abundances consistent with that chasm developing fully by 0.3 Gyr for stars with UMaG's metallicity. We see differences in the abundance of Li between UMaG members of the same spectral types, indicating that a real spread in the lithium abundance exists within this group.

Survey of Period Variations of Superhumps in SU UMa-Type Dwarf Novae. II The Second Year (2009-2010)

NASA Astrophysics Data System (ADS)

Kato, Taichi; Maehara, Hiroyuki; Uemura, Makoto; Henden, Arne; de Miguel, Enrique; Miller, Ian; Dubovsky, Pavol A.; Kudzej, Igor; Kiyota, Seiichiro; Hambsch, Franz-Josef; Tanabe, Kenji; Imamura, Kazuyoshi; Kunitomi, Nanae; Takagi, Ryosuke; Nose, Mikiha; Akazawa, Hidehiko; Masi, Gianluca; Nakagawa, Shinichi; Iino, Eriko; Noguchi, Ryo; Matsumoto, Katsura; Fujii, Daichi; Kobayashi, Hiroshi; Ogura, Kazuyuki; Ohtomo, Sachi; Yamashita, Kousei; Yanagisawa, Hirofumi; Itoh, Hiroshi; Bolt, Greg; Monard, Berto; Ohshima, Tomohito; Shears, Jeremy; Ruiz, Javier; Imada, Akira; Oksanen, Arto; Nelson, Peter; Gomez, Tomas L.; Staels, Bart; Boyd, David; Voloshina, Irina B.; Krajci, Thomas; Crawford, Tim; Stockdale, Chris; Richmond, Michael; Morelle, Etienne; Novák, Rudolf; Nogami, Daisaku; Ishioka, Ryoko; Brady, Steve; Simonsen, Mike; Pavlenko, Elena P.; Ringwald, Frederick A.; Kuramoto, Tetsuya; Miyashita, Atsushi; Pickard, Roger D.; Hynek, Tomáš; Dvorak, Shawn; Stubbings, Rod; Muyllaert, Eddy

2010-12-01

Continued from Kato et al. (2009, PASJ, 61, S395), we collected the times of superhump maxima for 68 SU UMa-type dwarf novae, mainly observed during the 2009-2010 season. The newly obtained data confirmed the basic findings reported in Kato et al. (ibid.): the presence of stages A-C and the predominance of positive period derivatives during stage B in systems with superhump periods shorter than 0.07 d. There was a systematic difference in the period derivatives for the systems with superhump periods longer than 0.075 d between this study and Kato et al. (ibid.). We suggest that this difference was possibly caused by a relative lack of frequently outbursting SU UMa-type dwarf novae in this period regime in the present study. We recorded a strong beat phenomenon during the 2009 superoutburst of IY UMa. A close correlation between the beat period and the superhump period suggests that the changing angular velocity of the apsidal motion of the elliptical disk is responsible for the variation of the superhump periods. We also described three new WZ Sge-type objects with established early superhumps and one with likely early superhumps. We suggest that two systems, VX For and EL UMa, are WZ Sge-type dwarf novae with multiple rebrightenings. The O - C variation in OT J213806.6+261957 suggests that the frequent absence of rebrightenings in very short-Porb objects can be the result of a sustained superoutburst plateau at the epoch when usual SU UMa-type dwarf novae return to quiescence, preceding a rebrightening. We also present a formulation for a variety of Bayesian extensions to traditional period analyses.

Observations and analysis of the contact binary H 235 in the open cluster NGC 752

NASA Astrophysics Data System (ADS)

Milone, E. F.; Stagg, C. R.; Sugars, B. A.; McVean, J. R.; Schiller, S. J.; Kallrath, J.; Bradstreet, D. H.

1995-01-01

The short-period variable star Heinemann 235 in the open cluster NGC 752 has been identified as a contact binary with a variable period of about 0 d 4118. BVRI light curves and radial velocity curves have been obtained and analyzed with enhanced versions of the Wilson-Devinney light curve program. We find that the system is best modeled as an A-type W UMa system, with a contact parameter of 0.21 +/- 0.11. The masses of the components are found to be 1.18 +/- 0.17 and 0.24 +/- 0.04 solar mass, with bolometric magnitudes of 3.60 +/- 0.10 and 5.21 +/- 0.13, for the hotter (6500 K, assumed) and cooler (6421 K) components, respectively, with Delta T=79 +/- 25 K. The distance to the binary is established at 381 +/- 17 pc. H235 becomes one of a relatively small number of open-cluster contact systems with detailed light curve analysis for which an age may be estimated. If it is coeval with the cluster, and with the detached eclipsing and double-lined spectroscopic binary H219 (DS And), H235 is approximately 1.8 Gyr old, and may provide a fiducial point for the evolution of contact systems. There is, however, evidence for dynamical evolution of the cluster and the likelihood of weak interactions over the age of the binary precludes the determination of its initial state with certainty.

Rotation and activity among solar-type stars of the Ursa Major Group

NASA Technical Reports Server (NTRS)

Soderblom, David R.; Mayor, Michel

1993-01-01

We examine rotation and chromospheric activity among G and K dwarfs recently shown to be members of the Ursa Major Group (UMaG). Rotation periods for UMaG stars are smaller than for stars of the same colors in the Hyades, and by an amount corresponding to the Skumanich relation. Most UMaG stars have about the same level of Ca II and K emission, implying that they also have nearly uniform intrinsic rotation rates. That means that the diversity of rotation rates and levels of activity seen among solar-type stars in the Alpha Persei and Pleiades clusters has largely converged by the age of UMaG (0.3 Gyr).

Is There a Substellar Object Orbiting the Solar-like Stable Contact Binary V2284 Cyg?

NASA Astrophysics Data System (ADS)

Wang, J.-J.; Jiang, L.-Q.; Zhang, B.; Zhao, S.-Q.; Yu, J.

2017-12-01

V2284 Cyg is a neglected W UMa-type binary star for photometric investigations. Monitored by the Kepler Space Telescope from 2009 to 2013, its light curves are continuously stable, suggesting that both components are inactive during this time interval. Based on the short-cadence observations, we determined the photometric solutions by using the 2013 version of the Wilson-Devinney code. These parameters reveal that V2284 Cyg is a W-type system with a degree of contact factor of f = 39.23% and a mass ratio of q = 2.90. Meanwhile, hundreds of times of minimum light were obtained and applied to analyze the orbital period changes. In the O-C diagram, a small-amplitude cyclic oscillation (A 3 = 0.00030 days and T 3 = 2.06 years) superimposed on a secular decreasing was found. The continuous decreasing may be a result from the mass transfer from the more massive component to the less massive one. With the long-term decreasing of the orbital period, this binary will evolve into a deeper contact system. Because the light curve is stable, the cyclic variation is plausibly explained as the light-travel time effect (LTTE) due to the presence of an additional body. The mass of the companion is {M}3\\sin i\\prime =0.036(+/- 0.003) {M}⊙ . If the orbital plane inclination is a random distribution, it is a brown dwarf with 66.7% probability. Therefore, the companion of V2284 Cyg is possibly the first candidate of the brown dwarf orbiting around contact binary, where both component are sharing a common convective envelope.

Three close binaries in different evolutionary stages in the old open cluster NGC 188

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, L. Y.; Qian, S. B.; Liu, L.

2014-02-01

NGC 188 is a good laboratory for studying the formation and evolution of W UMa type contact binaries due to its rich populations of them. We present a detailed photometric study of three short-period close binaries, EP Cep, ES Cep, and V369 Cep, in the old open cluster NGC 188 based on our two-set photometric observations. We discovered that both EP Cep and ES Cep are shallow-contact binaries with continuously decreasing periods. The difference is in their mass ratios. EP Cep has an extremely low-mass ratio, q = 0.15, while ES Cep has a relatively high-mass ratio, q = 0.69,more » indicating that they lie in different evolutionary stages. ES Cep is likely a newly formed contact binary via a Case A mass transfer, while EP Cep is an evolved system and may be on the oscillations caused by the combined effect of the thermal relaxation oscillation and the variable angular momentum loss. For another system, V369 Cep, we found that it is a primary-filling near-contact binary. Both the semidetached configuration and the continuous decrease in the orbital period indicate that it is undergoing a mass transfer from the primary component to the secondary one. This conclusion is in agreement with the excess luminosity seen in the light curves on the ingress of the secondary minimum produced by the impact of the mass transfer. All of the results suggest that V369 Cep is evolving into contact, and a shallow-contact high-mass ratio system similar to ES Cep will be formed. Then, it will evolve into a low-mass ratio contact binary just like EP Cep, and finally merge into a rapidly rotating single star.« less

Detection of the supercycle in V4140 Sagittarii: First eclipsing ER Ursae Majoris-like object

NASA Astrophysics Data System (ADS)

Kato, Taichi; Hambsch, Franz-Josef; Cook, Lewis M.

2018-05-01

We observed the deeply eclipsing SU UMa-type dwarf nova V4140 Sgr and established the very short supercycle of 69.7(3) d. There were several short outbursts between superoutbursts. These values, together with the short orbital period (0.06143 d), were similar to, but not as extreme as, those of ER UMa-type dwarf novae. The object is thus the first, long sought, eclipsing ER UMa-like object. This ER UMa-like nature can naturally explain the high (apparent) quiescent viscosity and unusual temperature profile in quiescence, which were claimed observational features against the thermal-tidal instability model. The apparently unusual outburst behavior can be reasonably explained by a combination of this ER UMa-like nature and the high orbital inclination, and there is no need to introduce mass transfer bursts from its donor star.

Detection of the supercycle in V4140 Sagittarii: First eclipsing ER Ursae Majoris-like object

NASA Astrophysics Data System (ADS)

Kato, Taichi; Hambsch, Franz-Josef; Cook, Lewis M.

2018-06-01

We observed the deeply eclipsing SU UMa-type dwarf nova V4140 Sgr and established the very short supercycle of 69.7(3) d. There were several short outbursts between superoutbursts. These values, together with the short orbital period (0.06143 d), were similar to, but not as extreme as, those of ER UMa-type dwarf novae. The object is thus the first, long sought, eclipsing ER UMa-like object. This ER UMa-like nature can naturally explain the high (apparent) quiescent viscosity and unusual temperature profile in quiescence, which were claimed observational features against the thermal-tidal instability model. The apparently unusual outburst behavior can be reasonably explained by a combination of this ER UMa-like nature and the high orbital inclination, and there is no need to introduce mass transfer bursts from its donor star.

Photometric study and orbital period analysis of the W UMa type contact binary VZ Psc

NASA Astrophysics Data System (ADS)

Ma, S.; Li, K.; Li, Q.-C.; Gao, H.-Y.

2018-02-01

VZ Psc is a W-type contact binary system with a short period of 0.26125897 days. B, V, Rc and Ic light curves of the eclipsing binary system were obtained by using the 1.0 m reflecting telescope at Weihai Observatory of Shandong University. By collecting 136 times of minimum light, we studied the orbital period change of VZ Psc. A sinusoidal variation was discovered in the O - C diagram, and the amplitude of 0.d0023 and the period of 17.7 year were obtained. This can be caused by Applegate mechanism or light-time effect. Both the mechanisms are suited according to our investigation, but we prefer the latter that the light-time effect due to the presence of a third body results in the cyclic variation. By using the W-D program, we analyzed the four color light curves. Because of the asymmetric light curves and the possible third body, we used the spot mode of W-D program with and without L3. We found that a hot spot on the primary component with the third light leads to the best result. A very high filling factor of 94.4% ± 2.8% and orbit inclination of 53.2° were obtained.

Ultraviolet studies of nova-like variables with the IUE

NASA Technical Reports Server (NTRS)

Guinan, E. F.

1983-01-01

KQ Mon is a new UX UMa-type nova-like variable. Optical spectra taken in 1978 reveal very shallow Balmer absorption lines and He I (wavelength 4471) absorption. There was no evidence of orbital variations but the appearance of the optical spectrum and the presence of low amplitude flickering suggested a strong similarity to CD-42 degrees 14462 (=V3885 Sgr) and other members of the UX UMa class. KQ Mon was observed at low dispersion with the IUE satellite. Six spectra taken with the short wavelength prime (SWP) camera are dominated by strong broad absorption lines due to N V, O I, Si III, Si IV, C IV, He II, N IV, and A1 III. There is little evidence of orbital phase modulation over the time baseline of the observations. Unlike UV observations of other UX UMa-type objects, KQ Mon exhibits no emission lines or P Cygni-type profiles and the velocity displacements appear to be smaller, suggesting the absence of a hot, high velocity wind characterizing other UX UMa stars. The relationship of KQ Mon to other UX UMa disk stars is discussed and a model is suggested to explain their observed properties and the lack of major outbursts.

LX Leo: A High Mass-Ratio Totally Eclipsing W-type W UMa System

NASA Astrophysics Data System (ADS)

Gürol, B.; Michel, R.; Gonzalez, C.

2017-10-01

We present the results of our investigation of the geometrical and physical parameters of the binary system LX Leo. Based on CCD BVRc light curves, and their analyses with the Wilson-Devinney code, new times of minima and light elements have been determined. According to our solution, the system is a high mass-ratio, totally eclipsing, W-type W UMa system. Combining our photometric solution with the empirical relation for W UMa type systems by Dimitrow & Kjurkchieva (2015), we derived the masses and radii of the components to be M1=0.43 M⊙, M2=0.81 M⊙, R1=0.58 R⊙ and R2=0.77 R⊙. In addition, the evolutionary condition of the system is discussed.

"Conical Hut": A Basic Form of House Types in Timor Island

NASA Astrophysics Data System (ADS)

Chen, Y. R.; Lim, Y. L.; Wang, M. H.; Chen, C. Y.

2015-08-01

Timor Island situates in the southeast end of Southeast Asia. The island accommodates many ethnic groups, which produce many diverse house types. As visiting East Timor in 2012 and Timor Island in 2014, we found the "Pair- House Type" widely spread over Timor Island. Uma Lulik (holy house), accommodating the ancestry soul, fireplace and elder's bed, and Uma Tidor (house for sleep), containing living, sleeping and working space, compose the pair-house. The research team visited 14 ethnic groups and their houses, some of which were measured and drawn into 3D models as back to Taiwan. Uma Tidors of each ethnic group are quite similar with rectangular volume and hip roof, however, one of the fourteen ethnic groups can build cylinder houses for Uma Tidor. Uma Luliks of different ethnic groups are diversified and special. One group of the Uma Luliks shows a rectangular or square volume sheltered by a hip roof. The other group of Uma Luliks presents a non-specific volume under a conical roof, that we called the "conical hut". Seven ethnic groups, Atoni, Weimua, Makassae, Mambai, Bunaq, Kemak and Bekais, have built "conical huts" for the use of Uma Lulik. People of the seven ethnic groups can construct a reasonable structural system to support the conical roof, and take good advantage of the space under the conical roof to meet their sacred needs and everyday life. "Conical Hut" may be regarded as the basic form of the house types adopted by the seven ethnic groups. It contains the basic spatial limits and the formal properties that the construction systems have to follow. Based on the concise rules of the basic form, people of each ethnic group use their talents, skills and building materials to generate variations of "conical hut", which are different in house scale, spatial layout, construction system and form. The "conical huts" contain the consistency that all the huts come from the basic form, meanwhile, they also present the diversification that each conical hut has differed. "Consistent but diversified", is one of the most interesting issues in typological study that we can observe in Timorese houses.

A new photometric study of the triple star system EF Draconis

NASA Astrophysics Data System (ADS)

Yang, Yuan-Gui

2012-04-01

We present new charge-coupled device (CCD) photometry for the triple star EF Draconis, obtained in 2009 and 2011. Using the updated Wilson-Devinney program, the photometric solutions were deduced from two sets of light curves. The results indicate that EF Dra is an A-type W UMa binary with a contact degree of f = 46.7%(±0.6%) and a third light of l3 ≃ 1.5%. Through analyzing the O — C curve, it is found that the orbital period shows a long-time increase with a light-time orbit. The period, semi-amplitude and eccentricity of the third body are Pmod = 17.20(±0.18) yr, A = 0.0039d(±0.0002d) and e = 0.49(±0.02) respectively. This kind of tertiary companion may extract angular momentum from the central system. The orbital period of EF Dra secularly increases at a rate of dP/dt = +3.72(±0.07) × 10-7 d yr-1, which may be interpreted by mass transfer from the less massive to the more massive component. As period increases, the separation between components may increase, which will cause the contact degree to decrease. With mass transferring, the spin angular momentum will increase, while the orbital angular momentum will decrease. Only if the contact configuration would merge at could this kind of deep-contact binary with period increasing, such as EF Dra, evolve into a rapidly-rotating single star.

Photometric Investigation and Possible Light-Time Effect in the Orbital Period of a Marginal Contact System, CW Cassiopeiae

NASA Astrophysics Data System (ADS)

Jiang, Tian-Yu; Li, Li-Fang; Han, Zhan-Wen; Jiang, Deng-Kai

2010-04-01

The first complete charge-coupled device (CCD) light curves in B and V passbands of a neglected contact binary system, CW Cassiopeiae (CW Cas), are presented. They were analyzed simultaneously by using the Wilson and Devinney (WD) code (1971, ApJ, 166, 605). The photometric solution indicates that CW Cas is a W-type W UMa system with a mass ratio of m2/m1 2.234, and that it is in a marginal contact state with a contact degree of ˜6.5% and a relatively large temperature difference of ˜327K between its two components. Based on the minimum times collected from the literature, together with the new ones obtained in this study, the orbital period changes of CW Cas were investigated in detail. It was found that a periodical variation overlaps with a secular period decrease in its orbital period. The long-term period decrease with a rate of dP/dt = -3.44 × 10-8d yr-1 can be interpreted either by mass transfer from the more-massive component to the less-massive with a rate of dm2/dt = -3.6 × 10-8M⊙ yr-1, or by mass and angular-momentum losses through magnetic braking due to a magnetic stellar wind. A low-amplitude cyclic variation with a period of T = 63.7 yr might be caused by the light-time effect due to the presence of a third body.

PHOTOMETRIC STUDY OF THE VERY SHORT PERIOD SHALLOW CONTACT BINARY DD COMAE BERENICES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, L.; Qian, S.-B.; Mikulasek, Z.

2010-07-15

The first photometric solutions of the very short period (VSP) close binary DD Comae Berenices (P = 0fd26920811) based on our new complete (IR){sub C} light curves are derived by the 2003 version Wilson-Van Hamme code. They show that the system belongs to shallow contact W-type W UMa systems with a degree of overcontact of 8.7%. The observed light curve distortions are explained by employing the spots model due to the late-type nature of both components. We have collected all available photometric data about the system with emphasis on the individual observational data, which we treated simultaneously using our ownmore » method based on the usage of computed model light curves as templates. We recalculated published times of light minimum and added new ones of our own to construct an O - C diagram that spans over 70 years. Using a least squares method orthogonal quadratic model function, we found that the orbital period of DD Com is continuously increasing with P-dot =0.00401(22) s yr{sup -1}. The period increase may be caused by the mass transfer from the less-massive component to the more-massive one. With the period increase, the binary is evolving from the present shallow contact phase to the broken stage predicted by the thermal relaxation oscillation (TRO) theory. Compared with other VSP systems, DD Com is a rare system that lies on the expanding phase of the TRO cycle. Until now, only four such systems including DD Com are found in this stage. Thus, this target is another good observational proof of the TRO theory in a very short period region.« less

Increasing Supercycle Lengths of Active SU UMa-type Dwarf Novae

NASA Astrophysics Data System (ADS)

Otulakowska-Hypka, M.; Olech, A.

2014-12-01

We present observational evidence that supercycle lengths of the most active SU UMa-type stars are increasing during the past decades. We analyzed a large number of photometric measurements from available archives and found that this effect is generic for this class of stars, independently of their evolutionary status. This finding is in agreement with previous predictions and the most recent work of Patterson et al. (2012) on BK Lyn.

A New Look at the Eclipse Timing Variation Diagram Analysis of Selected 3-body W UMa Systems

NASA Astrophysics Data System (ADS)

Christopoulou, P.-E.; Papageorgiou, A.

2015-07-01

The light travel effect produced by the presence of tertiary components can reveal much about the origin and evolution of over-contact binaries. Monitoring of W UMa systems over the last decade and/or the use of publicly available photometric surveys (NSVS, ASAS, etc.) has uncovered or suggested the presence of many unseen companions, which calls for an in-depth investigation of the parameters derived from cyclic period variations in order to confirm or reject the assumption of hidden companion(s). Progress in the analysis of eclipse timing variations is summarized here both from the empirical and the theoretical points of view, and a more extensive investigation of the proposed orbital parameters of third bodies is proposed. The code we have developed for this, implemented in Python, is set up to handle heuristic scanning with parameter perturbation in parameter space, and to establish realistic uncertainties from the least squares fitting. A computational example is given for TZ Boo, a W UMa system with a spectroscopically detected third component. Future options to be implemented include MCMC and bootstrapping.

Preliminary elements of the low mass ratio and moderate fill-out factor VSX J045718.3+405643 (GSC 02898-02901)

NASA Astrophysics Data System (ADS)

Acerbi, F.; Martignoni, M.; Barani, C.

2018-05-01

We present the results of our investigation of the geometrical parameters of the W UMa-type binary system VSX J045718.3+405643 (short name VSX J0457) based on new CCD B, V and Ic light curves. Our observations were carried out during six nights in November and December 2016 using the 0.25 m telescope of the Stazione Astronomica Betelgeuse in Magnago, Northern Italy. Six new times of minima and light elements have been determined and the observed light curves were analysed using the Wilson-Devinney code. The output model reveals that the system is a contact binary of A-Subtype of the W Ursae Majoris systems with a mass ratio of q ∼ 0.26 and a degree of contact factor f ∼ 32%. The primary component is hotter than the secondary by 95 K, this suggests us that the system is under thermal contact. The high orbital inclination (i = 82°.2) implies that VSX J0457 is a total eclipsing binary system and the photometric parameters here obtained are quite reliable. The absolute physical parameters of the two components in VSX J0457 are estimated. Based on these estimated parameters the evolutionary state of the system components is investigated and discussed. Combining our photometric solution with the 3-D correlation obtained for contact binaries by Gazeas (2009) we derive the masses and radii of the components of this eclipsing system as M1 = 1.44M⊙, M2 = 0.38M⊙, R1 = 1.55R⊙ and R2 = 0.87R⊙. The distance to VSX J0457 was calculated as 147 pc from this analysis, taking into account interstellar extinction.

Multi-color light curves and orbital period research of eclipsing binary V1073 Cyg

NASA Astrophysics Data System (ADS)

Tian, Xiao-Man; Zhu, Li-Ying; Qian, Sheng-Bang; Li, Lin-Jia; Jiang, Lin-Qiao

2018-02-01

New multi-color BV RcIc photometric observations are presented for the W UMa type eclipsing binary V1073 Cyg. The multi-color light curve analysis with the Wilson-Devinney procedure yielded the absolute parameters of this system, showing that V1073 Cyg is a shallow contact binary system with a fill-out factor f = 0.124(±0.011). We collected all available times of light minima spanning 119 yr, including CCD data to construct the O ‑ C curve, and performed detailed O ‑ C analysis. The O ‑ C diagram shows that the period change is complex. A long-term continuous decrease and a cyclic variation exist. The period is decreasing at a rate of Ṗ = ‑1.04(±0.18) × 10‑10 d cycle‑1 and, with the period decrease, V1073 Cyg will evolve to the deep contact stage. The cyclic variation with a period of P 3 = 82.7(±3.6) yr and an amplitude of A = 0.028(±0.002)d may be explained by magnetic activity of one or both components or the light travel time effect caused by a distant third companion with M 3(i‧ = 90°) = 0.511 M⊙.

The solar type deep low mass-ratio contact binary V658 Lyr: Photometric solution and preliminary elements

NASA Astrophysics Data System (ADS)

Martignoni, M.; Barani, C.; Acerbi, F.

2018-07-01

We present the first light curve analysis of the eclipsing binary V658 Lyr. B, V and Ic photometric observations made from 2014 to 2017 of this W UMa-type binary star are collected, the complete light curves were obtained in 2015 (4 nights) and 2016 (11 nights) and are used for a detailed photometric analysis to determine orbital and physical parameters using the Wilson-Devinney code. The results obtained indicates that V658 Lyr is an A-type overcontact binary system with both components of spectral type (G2 + G4). Based on our 17 ToM the short orbital period of the eclipsing binary was confirmed and revised to P = 0.3302577 days. The orbital period was found to show a cyclic variations and a decrease rate of dP/dt = - 2.97 × 10 -7 days yr-1 , which can be interpreted as a mass transfer from the more massive component to the less massive one. We have not found an asymmetry of the light curves. The mass of the primary and secondary stars are calculated to be M1 = 1.18M⊙( ± 0.08) and M2 = 0.21M⊙( ± 0.01) indicating the primary to be underluminous for its mass and the secondary to be overluminous for its mass.

THE LEECH EXOPLANET IMAGING SURVEY: ORBIT AND COMPONENT MASSES OF THE INTERMEDIATE-AGE, LATE-TYPE BINARY NO UMa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schlieder, Joshua E.; Skemer, Andrew J.; Hinz, Philip

2016-02-10

We present high-resolution Large Binocular Telescope LBTI/LMIRcam images of the spectroscopic and astrometric binary NO UMa obtained as part of the LBT Interferometer Exozodi Exoplanet Common Hunt exoplanet imaging survey. Our H-, K{sub s}-, and L′-band observations resolve the system at angular separations <0.″09. The components exhibit significant orbital motion over a span of ∼7 months. We combine our imaging data with archival images, published speckle interferometry measurements, and existing spectroscopic velocity data to solve the full orbital solution and estimate component masses. The masses of the K2.0 ± 0.5 primary and K6.5 ± 0.5 secondary are 0.83 ± 0.02 M{sub ⊙} and 0.64 ± 0.02 M{sub ⊙},more » respectively. We also derive a system distance of d = 25.87 ± 0.02 pc and revise the Galactic kinematics of NO UMa. Our revised Galactic kinematics confirm NO UMa as a nuclear member of the ∼500 Myr old Ursa Major moving group, and it is thus a mass and age benchmark. We compare the masses of the NO UMa binary components to those predicted by five sets of stellar evolution models at the age of the Ursa Major group. We find excellent agreement between our measured masses and model predictions with little systematic scatter between the models. NO UMa joins the short list of nearby, bright, late-type binaries having known ages and fully characterized orbits.« less

The Cluster AgeS Experiment (CASE). Variable Stars in the Field of the Globular Cluster M22

NASA Astrophysics Data System (ADS)

Rozyczka, M.; Thompson, I. B.; Pych, W.; Narloch, W.; Poleski, R.; Schwarzenberg-Czerny, A.

2017-09-01

The field of the globular cluster M22 (NGC 6656) was monitored between 2000 and 2008 in a search for variable stars. BV light curves were obtained for 359 periodic, likely periodic, and long-term variables, 238 of which are new detections. 39 newly detected variables, and 63 previously known ones are members or likely members of the cluster, including 20 SX Phe, 10 RRab and 16 RRc type pulsators, one BL Her type pulsator, 21 contact binaries, and 9 detached or semi-detached eclipsing binaries. The most interesting among the identified objects are V112 - a bright multimode SX Phe pulsator, V125 - a β Lyr type binary on the blue horizontal branch, V129 - a blue/yellow straggler with a W UMa-like light curve, located halfway between the extreme horizontal branch and red giant branch, and V134 - an extreme horizontal branch object with P=2.33 d and a nearly sinusoidal light curve. All four of them are proper motion members of the cluster. Among nonmembers, a P=2.83 d detached eclipsing binary hosting a δ Sct type pulsator was found, and a peculiar P=0.93 d binary with ellipsoidal modulation and narrow minimum in the middle of one of the descending shoulders of the sinusoid. We also collected substantial new data for previously known variables. In particular we revise the statistics of the occurrence of the Blazhko effect in RR Lyr type variables of M22.

Observations and light curve solutions of a selection of shallow-contact W UMa binaries

NASA Astrophysics Data System (ADS)

Kjurkchieva, Diana P.; Popov, Velimir A.; Vasileva, Doroteya L.; Petrov, Nikola I.

2018-07-01

Photometric observations in Sloan g‧ and i‧ bands of the W UMa binaries V0951 Per, CSS J062803.2+571604, CSS J222157.2+275308, CSS J075135.6+382028, V0338 Dra, NSVS 2256852, NSVS 4666412, V1355 Tau, NSVS 4808227, NSVS 4726498, CSS J075350.1+264830 and HL Lyn are presented. The light curve solutions revealed that these binaries have overcontact configurations with small fillout factors (within 0.1-0.2). Seven of them undergo total eclipses and their photometric mass ratios should be accepted with confidence. The temperature differences of the components of CSS J062803.2+571604 and NSVS 2256852 exceed 1100 K which is unusual for overcontact binaries. We suspect that NSVS 2256852 is a probable candidate for merger due to its small mass ratio of q = 0.16 and to the registered decreasing of the orbital period.

New precision orbits of bright double-lined spectroscopic binaries. IX. HD 54371, HR 2692, and 16 ursa majoris

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fekel, Francis C.; Williamson, Michael H.; Muterspaugh, Matthew W.

2015-02-01

With extensive sets of new radial velocities we have determined orbital elements for three previously known spectroscopic binaries, HD 54371, HR 2692, and 16 UMa. All three systems have had the lines of their secondaries detected for the first time. The orbital periods range from 16.24 to 113.23 days, and the three binaries have modestly or moderately eccentric orbits. The secondary to primary mass ratios range from 0.50 to 0.64. The orbital dimensions (a{sub 1} sin i and a{sub 2} sin i) and minimum masses (m{sub 1} sin{sup 3} i and m{sub 2} sin{sup 3} i) of the binary componentsmore » all have accuracies of ⩽1%. With our spectroscopic results and the Hipparcos data, we also have determined astrometric orbits for two of the three systems, HR 2692 and 16 UMa. The primaries of HD 54371 and 16 UMa are solar-type stars, and their secondaries are likely K or M dwarfs. The primary of HR 2692 is a late-type subgiant and its secondary is a G or K dwarf. The primaries of both HR 2692 and 16 UMa may be pseudosynchronously rotating, while that of HD 54371 is rotating faster than its pseudosynchronous velocity.« less

Period Variations in the Close Binary BM UMa

NASA Astrophysics Data System (ADS)

Virnina, Natalia A.; Panko, Elena; Sergienko, O. G.; Murnikov, Boris A.; Gubin, E. G.; Klabukova, A. V.; Movchan, A. I.

2010-12-01

We present the results of analysing of the light curve and O-C variations in the eclipsing system BM UMa, based on V-band observations which cover the period from JD 2454933 to 2454961 using two robotic remotely-controlled telescopes of Tzec Maun Observatory (USA) along with observations made with the RK-600 telescope of Odessa Astronomical Observatory. The full light curve displays a total primary eclipse with a duration 0.06 of the period, or 24 minutes, and a partial secondary eclipse, with both maxima of equal magnitude. For our obesrvations, we determined the statistically optimal values of the initial epoch of T0 = 2454944.2814 ± 0.0001 and orbital period of P = 0.d271226± 0.000002. The depths of primary and secondary minima are nearly equal, 0.m838 ± 0.006 and 0.m748 ± 0.006, respectively. The physical parameters of the system were calculated using the Wilson-Devinney code, appended with the Monte Carlo search algorithm. The result establishes BM UMa as a contact system (fillout factor 10.7%) with parameters: mass ratio 0.538 ± 0.001, inclination 86.°815 ± 0.005, and temperatures of components 4700 ± 20 K and 4510 ± 10 K. The more massive component is larger and cooler. The 72 archival and 11 newly-obtained times of light minimum cover the interval 1961-2010 and allowed us to exclude possible systematic period variations in BM UMa and to determine an initial epoch of HJD 2447927.382 and orbital period of P = 0.d2712209± 0.0000006.

THE VARYING LIGHT CURVE AND TIMINGS OF THE ULTRASHORT-PERIOD CONTACT BINARY KIC 9532219

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Jae Woo; Hong, Kyeongsoo; Koo, Jae-Rim

2016-03-20

KIC 9532219 is a W UMa-type eclipsing binary with an orbital period of 0.1981549 days that is below the short-period limit (∼0.22 days) of the period distribution for contact binaries. The Kepler light curve of the system exhibits striking changes in both eclipse depths and light maxima. Applying third-body and spot effects, the light-curve synthesis indicates that the eclipsing pair is currently in a marginal contact stage with a mass ratio of q = 1.20, an orbital inclination of i = 66.°0, a temperature difference of T{sub 1}–T{sub 2} = 172 K, and a third light of l{sub 3} = 75.9%.more » To understand the light variations with time, we divided up the light curve into 312 segments and analyzed them separately. The results reveal that variation of eclipse depth is primarily caused by changing amounts of contamination due to the nearby star KIC 9532228 between the Kepler Quarters and that the variable O’Connell effect originates from the starspot activity on the less massive primary component. Based on our light-curve timings, a period study of KIC 9532219 indicates that the orbital period has varied as a combination of a downward parabola and a light-travel-time (LTT) effect due to a third body, which has a period of 1196 days and a minimum mass of 0.0892 M{sub ⊙} in an orbit of eccentricity 0.150. The parabolic variation could be a small part of a second LTT orbit due to a fourth component in a wider orbit, instead of either mass transfer or angular momentum loss.« less

Photometric Study of the Solar Type Pre-Contact Binary, V2421 Cygni

NASA Astrophysics Data System (ADS)

Hill, Robert L.; Shebs, T.; Samec, R. G.; Kring, J.; Van Hamme, W. V.; Faulkner, D. R.

2013-06-01

We present the first precision BVRI light curves, and synthetic light curve solutions and a period study for the 14th magnitude (V) pre-contact W UMa Binary, V2421 Cygni. Observations were taken with the NURO 0.81-m Lowell reflector on 30 September, 1 and 2 October. Our light curves were premodeled with Binary Maker 3.0, and solved with the Wilson-Devinney program. The observations included 140 B, 149 V, 139 R and 135 I individual and calibrated observations. These were taken with the Lowell CRYOTIGER cooled (-100k) 2KX2K NASACAM. Three mean times of minimum light were determined, including HJDMin I = 2455469.82375±0.00037, and 2455471.72232±0.0012 and HJDMin II = 2455470.77149±0.0012. Eight eclipse timings were taken from the the literature for our calculation of its first precision ephemeris: JD Tmin I = 2455469.8238± 0.0047 + 0.6331290 ± 0.0000015 d*E The light curve has the appearance of an Algol (EA) type, however it is made up of dwarf solar type components in a detached mode with a period of only 0.6331 days. The light curve solution gives a mass ratio of ~0.5, an inclination of 86° and amplitudes of 1.3, 1.1, 0.98, and 0.87 in B,V,R and I, respectively. Flare-like disruptions occur in the light curves following the primary and secondary eclipses. The fill-outs are 83% and 98% for star one (hotter more massive component) and star two, respectively. The model includes two hot spots, possibly, stream spots (one a direct hit and the second, a splash spot). Further observations are needed to determine its orbital evolution. We thank USC, Lancaster for their support of our membership in NURO for the past 8 years, the American Astronomical Society for its support through its small research program and Arizona Space grant for the partial support for our student’s travel.

Long term evolution of surface features on the unusual close binary V361 Lyr

NASA Astrophysics Data System (ADS)

Lister, T. A.

2009-02-01

V361 Lyr has been recognized as an unusual, possibly unique, pre-contact binary which is though to be evolving from a detached binary system into a W UMa contact binary system due to Angular Momentum Loss (AML) and mass transfer. The mass transfer and resulting hot spot on the secondary star allow the physics of accretion to be studied without the normal difficulties of disks and winds that are present in T Tauri stars. I present light curves obtained over a 10 year period as part of long term monitoring program obtained with a variety of telescopes, collect all available times of minima from the literature along with those determined from the light curves and determine the rate of period change.

Survey of period variations of superhumps in SU UMa-type dwarf novae. VIII. The eighth year (2015-2016)

NASA Astrophysics Data System (ADS)

Kato, Taichi; Hambsch, Franz-Josef; Monard, Berto; Vanmunster, Tonny; Maeda, Yutaka; Miller, Ian; Itoh, Hiroshi; Kiyota, Seiichiro; Isogai, Keisuke; Kimura, Mariko; Imada, Akira; Tordai, Tamás; Akazawa, Hidehiko; Tanabe, Kenji; Otani, Noritoshi; Ogi, Minako; Ando, Kazuko; Takigawa, Naoki; Dubovsky, Pavol A.; Kudzej, Igor; Shugarov, Sergey Yu.; Katysheva, Natalia; Golysheva, Polina; Gladilina, Natalia; Chochol, Drahomir; Starr, Peter; Kasai, Kiyoshi; Pickard, Roger D.; de Miguel, Enrique; Kojiguchi, Naoto; Sugiura, Yuki; Fukushima, Daiki; Yamada, Eiji; Uto, Yusuke; Kamibetsunawa, Taku; Tatsumi, Taiki; Takeda, Nao; Matsumoto, Katsura; Cook, Lewis M.; Pavlenko, Elena P.; Babina, Julia V.; Pit, Nikolaj V.; Antonyuk, Oksana I.; Antonyuk, Kirill A.; Sosnovskij, Aleksei A.; Baklanov, Aleksei V.; Kafka, Stella; Stein, William; Voloshina, Irina B.; Ruiz, Javier; Sabo, Richard; Dvorak, Shawn; Stone, Geoff; Andreev, Maksim V.; Antipin, Sergey V.; Zubareva, Alexandra M.; Zaostrojnykh, Anna M.; Richmond, Michael; Shears, Jeremy; Dubois, Franky; Logie, Ludwig; Rau, Steve; Vanaverbeke, Siegfried; Simon, Andrei; Oksanen, Arto; Goff, William N.; Bolt, Greg; Dębski, Bartłomiej; Kochanek, Christopher S.; Shappee, Benjamin; Stanek, Krzysztof Z.; Prieto, José L.; Stubbings, Rod; Muyllaert, Eddy; Hiraga, Mitsutaka; Horie, Tsuneo; Schmeer, Patrick; Hirosawa, Kenji

2016-08-01

Continuing the project described by Kato et al. (2009, PASJ, 61, S395), we collected times of superhump maxima for 128 SU UMa-type dwarf novae observed mainly during the 2015-2016 season and characterized these objects. The data have improved the distribution of orbital periods, the relation between the orbital period and the variation of superhumps, and the relation between period variations and the rebrightening type in WZ Sge-type objects. Coupled with new measurements of mass ratios using growing stages of superhumps, we now have a clearer and statistically greatly improved evolutionary path near the terminal stage of evolution of cataclysmic variables. Three objects (V452 Cas, KK Tel, and ASASSN-15cl) appear to have slowly growing superhumps, which is proposed to reflect the slow growth of the 3 : 1 resonance near the stability border. ASASSN-15sl, ASASSN-15ux, SDSS J074859.55+312512.6, and CRTS J200331.3-284941 are newly identified eclipsing SU UMa-type (or WZ Sge-type) dwarf novae. ASASSN-15cy has a short (˜0.050 d) superhump period and appears to belong to EI Psc-type objects with compact secondaries having an evolved core. ASASSN-15gn, ASASSN-15hn, ASASSN-15kh, and ASASSN-16bu are candidate period bouncers with superhump periods longer than 0.06 d. We have newly obtained superhump periods for 79 objects and 13 orbital periods, including periods from early superhumps. In order that future observations will be more astrophysically beneficial and rewarding to observers, we propose guidelines on how to organize observations of various superoutbursts.

Types of Contact Lenses

MedlinePlus

... Consumer Devices Consumer Products Contact Lenses Types of Contact Lenses Share Tweet Linkedin Pin it More sharing ... Orthokeratology (Ortho-K) Decorative (Plano) Contact Lenses Soft Contact Lenses Soft contact lenses are made of soft, ...

Stellar Kinematic Groups. II. A Reexamination of the Membership, Activity, and Age of the Ursa Major Group

NASA Astrophysics Data System (ADS)

King, Jeremy R.; Villarreal, Adam R.; Soderblom, David R.; Gulliver, Austin F.; Adelman, Saul J.

2003-04-01

Utilizing Hipparcos parallaxes, original radial velocities and recent literature values, new Ca II H and K emission measurements, literature-based abundance estimates, and updated photometry (including recent resolved measurements of close doubles), we revisit the Ursa Major moving group membership status of some 220 stars to produce a final clean list of nearly 60 assured members, based on kinematic and photometric criteria. Scatter in the velocity dispersions and H-R diagram is correlated with trial activity-based membership assignments, indicating the usefulness of criteria based on photometric and chromospheric emission to examine membership. Closer inspection, however, shows that activity is considerably more robust at excluding membership, failing to do so only for <=15% of objects, perhaps considerably less. Our UMa members demonstrate nonzero vertex deviation in the Bottlinger diagram, behavior seen in older and recent studies of nearby young disk stars and perhaps related to Galactic spiral structure. Comparison of isochrones and our final UMa group members indicates an age of 500+/-100 Myr, some 200 Myr older than the canonically quoted UMa age. Our UMa kinematic/photometric members' mean chromospheric emission levels, rotational velocities, and scatter therein are indistinguishable from values in the Hyades and smaller than those evinced by members of the younger Pleiades and M34 clusters, suggesting these characteristics decline rapidly with age over 200-500 Myr. None of our UMa members demonstrate inordinately low absolute values of chromospheric emission, but several may show residual fluxes a factor of >=2 below a Hyades-defined lower envelope. If one defines a Maunder-like minimum in a relative sense, then the UMa results may suggest that solar-type stars spend 10% of their entire main-sequence lives in periods of precipitously low activity, which is consistent with estimates from older field stars. As related asides, we note six evolved stars (among our UMa nonmembers) with distinctive kinematics that lie along a 2 Gyr isochrone and appear to be late-type counterparts to disk F stars defining intermediate-age star streams in previous studies, identify a small number of potentially very young but isolated field stars, note that active stars (whether UMa members or not) in our sample lie very close to the solar composition zero-age main sequence, unlike Hipparcos-based positions in the H-R diagram of Pleiades dwarfs, and argue that some extant transformations of activity indices are not adequate for cool dwarfs, for which Ca II infrared triplet emission seems to be a better proxy than Hα-based values for Ca II H and K indices.

Absolute Parameters and Physical Nature of the Low-amplitude Contact Binary HI Draconis

NASA Astrophysics Data System (ADS)

Papageorgiou, A.; Christopoulou, P.-E.

2015-05-01

We present a detailed investigation of the low-amplitude contact binary HI Dra based on the new VRcIc CCD photometric light curves (LCs) combined with published radial velocity (RV) curves. Our completely covered LCs were analyzed using PHOEBE and revealed that HI Dra is an overcontact binary with low fill-out factor f = 24 ± 4(%) and temperature difference between the components of 330 K. Two spotted models are proposed to explain the LC asymmetry, between which the A subtype of W UMa type eclipsing systems, with a cool spot on the less massive and cooler component, proves to be more plausible on evolutionary grounds. The results and stability of the solutions were explored by heuristic scan and parameter perturbation to provide a consistent and reliable set of parameters and their errors. Our photometric modeling and RV curve solution give the following absolute parameters of the hot and cool components, respectively: Mh = 1.72 ± 0.08 {{M}⊙ } and Mc = 0.43 ± 0.02 {{M}⊙ }, Rh = 1.98 ± 0.03 {{R}⊙ } and Rc = 1.08 ± 0.02 {{R}⊙ }, and Lh = 9.6 ± 0.1 {{L}⊙ } and Lc = 2.4 ± 0.1 {{L}⊙ }. Based on these results the initial masses of the progenitors (1.11 ± 0.03 {{M}⊙ } and 2.25 ± 0.07 {{M}⊙ }, respectively) and a rough estimate of the age of the system of 2.4 Gyr are discussed.

DEEP, LOW-MASS RATIO OVERCONTACT BINARY SYSTEMS. XII. CK BOOTIS WITH POSSIBLE CYCLIC MAGNETIC ACTIVITY AND ADDITIONAL COMPANION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Y.-G.; Qian, S.-B.; Soonthornthum, B., E-mail: yygcn@163.com, E-mail: qsb@ynao.ac.cn

2012-05-15

We present precision CCD photometry, a period study, and a two-color simultaneous Wilson code solution of the short-period contact binary CK Bootis. The asymmetric light curves were modeled by a dark spot on the primary component. The result identifies that CK Boo is an A-type W UMa binary with a high fillout of f = 71.7({+-} 4.4)%. From the O - C curve, it is found that the orbital period changes in a complicated mode, i.e., a long-term increase with two sinusoidal variations. One cyclic oscillation with a period of 10.67({+-} 0.20) yr may result from magnetic activity cycles, whichmore » are identified by the variability of Max. I - Max. II. Another sinusoidal variation (i.e., A = 0.0131 days({+-} 0.0009 days) and P{sub 3} = 24.16({+-} 0.64) yr) may be attributed to the light-time effect due to a third body. This kind of additional companion can extract angular momentum from the central binary system. The orbital period secularly increases at a rate of dP/dt = +9.79 ({+-}0.80) Multiplication-Sign 10{sup -8} days yr{sup -1}, which may be interpreted by conservative mass transfer from the secondary to the primary. This kind of deep, low-mass ratio overcontact binaries may evolve into a rapid-rotating single star, only if the contact configuration do not break down at J{sub spin} > (1/3)J{sub orb}.« less

First photometric study of the W UMa system GSC 1042-2191

NASA Astrophysics Data System (ADS)

Bulut, A.; Bulut, İ.; Demircan, O.

2016-04-01

We present new photometric observations covering eight minima times for the eclipsing binary GSC 1042-2191. The light curves in BVRI colors were analyzed by using WD-code for the system parameters. Eight minima times were obtained from the new observations. The system is found a low mass ratio (q = 0.148), A-type over-contact binary with a fill out parameter of f = 65.01 ± 12.18%. The preliminary absolute dimensions (M1= 1.26 ± 0.06 M⊙, M2 = 0.18 ± 0.06 M⊙, R1 = 1.54 ± 0.20 R⊙, R2 = 0.69 ± 0.01 R⊙, L1 =3.30 ± 0.30 L⊙ and L2 = 0.59 ± 0.20 L⊙) indicate the very much oversized and over-luminous secondary component, by assuming the present luminosity of the secondary is its main sequence luminosity, we predict the original mass is about 0.8 M⊙, this means the present secondary could be transferred and/or lost 77% of its original mass and only its core is left.

Special tinted contact lens on colour-defects.

PubMed

Mutilab, H A; Sharanjeet-Kaur; Keu, L K; Choo, P F

2012-01-01

The objective of this study was to determine the visual function of colour-deficient subjects when wearing special red tint contact lenses. A total of 17 subjects with congenital colour vision deficiency (14 deutans and 3 protans), voluntarily participated in this study. The average age for the subjects was 23.00 ± 4.06 years old. Visual functions tested were visual acuity (LogMAR), contrast sensitivity (FACT Chart) and stereopsis (TNO and Howard Dolman tests). Two types of special red tint lenses were used in this study; Type I (light red) and Type II (dark red). The protans and deutans showed no significant changes in visual acuity and contrast sensitivity when wearing either type of contact lens. Stereopsis testing using the Horward-Dolman test gave no significant changes but significant differences were seen using the TNO test. Stereopsis using the TNO test was significantly poorer with the red tinted contact lenses compared to without for both protons and deutans. Testing binocularly with Ishihara plates showed that 88% (n=15) of patients passed the test with Type I and Type II contact lenses. When D15 test was done, 3 patients (17.6%) were 'normal' when using the Type I contact lenses and 2 patients (11.8%) were 'normal' when using the Type II contact lenses. However, with FM100Hue test, most patients showed deutan responses. Total error scores (TES) were found to be higher with Type I and Type II contact lenses compared to without. The Type I and II special tinted contact lens used in this study did not cause a reduction of visual acuity and contrast sensitivity for the colour defects. Stereopsis was also not reduced with the Type I and Type II contact lenses for the colour defects except when tested with the TNO test. Colour vision defects became difficult to detect using the Ishihara plates but FM100Hue test did not show any improvement with the Type I and Type II contact lenses.

49 CFR 236.560 - Contact element, mechanical trip type; location with respect to rail.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Contact element, mechanical trip type; location... Instructions; Locomotives § 236.560 Contact element, mechanical trip type; location with respect to rail. Contact element of automatic train stop device of the mechanical trip type shall be maintained at a height...

BVR{sub c}I{sub c} observations and analyses on V2421 Cygni, a precontact W UMa binary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samec, R. G.; Shebs, Travis S.; Faulkner, D. R.

2014-01-01

We present the first precision BVRI light curves, synthetic light curve solutions, and a period study for the high amplitude solar type binary, V2421 Cygni. The light curves have the appearance of an Algol (EA) type; however, it is made up of dwarf solar type components in a detached mode with a period of only 0.6331 days with an amplitude of about a full magnitude, i.e., it is a precontact W UMa binary. Flare-like disruptions occur in the light curves following the primary and secondary eclipses possibly due to the line-of-sight track of a gas stream. An associated stream spotmore » and splash spot cause bright equatorial spots on the stellar surface of the primary star. The more massive star is the gainer, making this system a classic, albeit dwarf, Algol.« less

Refined investigation of the low-amplitude contact binary V1003 Her

NASA Astrophysics Data System (ADS)

Papageorgiou, A.; Christopoulou, P.-E.; Pribulla, T.; Vaňko, M.

2015-05-01

We present an extensive analysis of the low amplitude, contact binary V1003 Her, based on the new , CCD photometric light curves in combination with published radial velocity (RV) curves. We investigate the stable configurations for the system with two independent methods and modeling tools: PHOEBE, ROCHE, via heuristic scanning and genetic algorithms, although the very low inclination of the system can place limitations. All methods indicate that V1003 Her is most likely in overcontact state with unequal components with temperature difference of 550 K, a mass ratio of q=0.373 and a contact degree of 36±10 %. As it is viewed at the very low inclination of i˜38∘±1∘, if its configuration is confirmed, it will be among the most massive W-subtype of W UMa systems. This conclusion is also supported by other published models. However, in order to conclude reliable physical properties of the system, the high-precise based-ground photometry (or satellite photometry) and spectroscopic follow-up of V1003 Her is required.

High voltage semiconductor devices and methods of making the devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matocha, Kevin; Chatty, Kiran; Banerjee, Sujit

A multi-cell MOSFET device including a MOSFET cell with an integrated Schottky diode is provided. The MOSFET includes n-type source regions formed in p-type well regions which are formed in an n-type drift layer. A p-type body contact region is formed on the periphery of the MOSFET. The source metallization of the device forms a Schottky contact with an n-type semiconductor region adjacent the p-type body contact region of the device. Vias can be formed through a dielectric material covering the source ohmic contacts and/or Schottky region of the device and the source metallization can be formed in the vias.more » The n-type semiconductor region forming the Schottky contact and/or the n-type source regions can be a single continuous region or a plurality of discontinuous regions alternating with discontinuous p-type body contact regions. The device can be a SiC device. Methods of making the device are also provided.« less

High voltage semiconductor devices and methods of making the devices

DOEpatents

Matocha, Kevin; Chatty, Kiran; Banerjee, Sujit

2017-02-28

A multi-cell MOSFET device including a MOSFET cell with an integrated Schottky diode is provided. The MOSFET includes n-type source regions formed in p-type well regions which are formed in an n-type drift layer. A p-type body contact region is formed on the periphery of the MOSFET. The source metallization of the device forms a Schottky contact with an n-type semiconductor region adjacent the p-type body contact region of the device. Vias can be formed through a dielectric material covering the source ohmic contacts and/or Schottky region of the device and the source metallization can be formed in the vias. The n-type semiconductor region forming the Schottky contact and/or the n-type source regions can be a single continuous region or a plurality of discontinuous regions alternating with discontinuous p-type body contact regions. The device can be a SiC device. Methods of making the device are also provided.

Lithium-drifted silicon detector with segmented contacts

DOEpatents

Tindall, Craig S.; Luke, Paul N.

2006-06-13

A method and apparatus for creating both segmented and unsegmented radiation detectors which can operate at room temperature. The devices include a metal contact layer, and an n-type blocking contact formed from a thin layer of amorphous semiconductor. In one embodiment the material beneath the n-type contact is n-type material, such as lithium compensated silicon that forms the active region of the device. The active layer has been compensated to a degree at which the device may be fully depleted at low bias voltages. A p-type blocking contact layer, or a p-type donor material can be formed beneath a second metal contact layer to complete the device structure. When the contacts to the device are segmented, the device is capable of position sensitive detection and spectroscopy of ionizing radiation, such as photons, electrons, and ions.

Complementary Barrier Infrared Detector (CBIRD) Contact Methods

NASA Technical Reports Server (NTRS)

Ting, David Z.; Hill, Cory J.; Gunapala, Sarath D.

2013-01-01

The performance of the CBIRD detector is enhanced by using new device contacting methods that have been developed. The detector structure features a narrow gap adsorber sandwiched between a pair of complementary, unipolar barriers that are, in turn, surrounded by contact layers. In this innovation, the contact adjacent to the hole barrier is doped n-type, while the contact adjacent to the electron barrier is doped p-type. The contact layers can have wider bandgaps than the adsorber layer, so long as good electrical contacts are made to them. If good electrical contacts are made to either (or both) of the barriers, then one could contact the barrier(s) directly, obviating the need for additional contact layers. Both the left and right contacts can be doped either n-type or ptype. Having an n-type contact layer next to the electron barrier creates a second p-n junction (the first being the one between the hole barrier and the adsorber) over which applied bias could drop. This reduces the voltage drop over the adsorber, thereby reducing dark current generation in the adsorber region.

Ultra-thin ohmic contacts for p-type nitride light emitting devices

DOEpatents

Raffetto, Mark [Raleigh, NC; Bharathan, Jayesh [Cary, NC; Haberern, Kevin [Cary, NC; Bergmann, Michael [Chapel Hill, NC; Emerson, David [Chapel Hill, NC; Ibbetson, James [Santa Barbara, CA; Li, Ting [Ventura, CA

2012-01-03

A semiconductor based Light Emitting Device (LED) can include a p-type nitride layer and a metal ohmic contact, on the p-type nitride layer. The metal ohmic contact can have an average thickness of less than about 25 .ANG. and a specific contact resistivity less than about 10.sup.-3 ohm-cm.sup.2.

Ultraviolet colors of W Ursae Majoris - Gravity darkening, temperature differences, and the cause of W-type light curves

NASA Technical Reports Server (NTRS)

Eaton, J. A.; Wu, C.-C.; Rucinski, S. M.

1980-01-01

The paper presents photometry of the prototype W UMa binary system in three ultraviolet bands with the ANS satellite. It was found that W UMa has low-gravity darkening beta of 0.03; that temperature differences between the components not established by gravity darkening are insignificant; and that the bolometric albedo is not very large. It was also found that W UMa is limb-darkened in the ultraviolet region, and that the inner hemisphere of the less massive component is hotter than that predicted by gravity darkening and the reflection effect. It was concluded that about 20% of the surface area of the component responsible for large gravity darkening is covered by dark spots distributed uniformly in the longitudinal direction. An observational value of the convective darkening exponent of 0.054 plus or minus 0.02 is proposed.

Recent Observations of the Neglected Southern Eclipsing Binary Systems V343 Cen, UY Mus, HT Aps, and V1961 Sgr

NASA Astrophysics Data System (ADS)

Faulkner, D. R.; Samec, R. G.; Stoddard, M. L.; McKenzie, R.; Rebar, D.; Lavoie, G. D.; Moody, S.; Miller, J.; Van Hamme, W.

2002-12-01

As a part of our continuing search for solar type binaries with impacting gas streams, we present light curves of V343 Cen, UY Mus, HT Aps, and V1961 Sgr. These are all neglected variables whose observing histories show little or no observations since their discovery. The CCD observations were taken at the 0.9-m at CTI0 in the UBVRI Johnson-Cousins system. The observations were taken in on 2002, May 31-June 8 and 2001, May 16 - 23 respectively. UY Mus is a near contact binary with a large difference in eclipse depths of V = 0.67 mag. Otherwise the curve appears symmetric. The times of minimum light determined from our data are HJD Min I = 242047.62316(6) and Min II = 2452050.4874(3) where the value in parentheses is the standard error in the last decimal place. V1961 Sgr (GCVS 6848 485) is a W UMa binary with a difference in eclipse depths of V = 0.11 mag and a possible variable spot area causing a V = 0.04 mag variation in MAX I from night to night. HT Aps is a near contact solar type binary with a large difference in eclipse depths of V= 0.47 mag and a somewhat asymmetric (difference in maxima, V= 0.4 mag) light curve. It is a possibly a candidate for a binary with a gas stream. One time of minimum light determined from our data is HJD Min I = 2452331.63725 (12). V343 Cen is a near contact binary with a large difference in eclipse depths of V= 0.42 mag and distortions that give evidence of a gas stream collision. The difference in maxima is V = 0.07 mag. The curve shows little variation over the 4 day interval of observation. Light curves analyses, new period determinations and photometric data will be presented for these variables. Acknowledgements: We wish to thank the American Astronomical Society for their continued support of our undergraduate research programs through their small research grants. Faulkner and Samec were visiting Astronomers, Cerro Tololo InterAmerican Observatory, National Optical Astronomical Observatories, which are operated by the Association of Universities for Research in Astronomy, Inc. under contract with the National Science Foundation.

Method of forming contacts for a back-contact solar cell

DOEpatents

Manning, Jane

2013-07-23

Methods of forming contacts for back-contact solar cells are described. In one embodiment, a method includes forming a thin dielectric layer on a substrate, forming a polysilicon layer on the thin dielectric layer, forming and patterning a solid-state p-type dopant source on the polysilicon layer, forming an n-type dopant source layer over exposed regions of the polysilicon layer and over a plurality of regions of the solid-state p-type dopant source, and heating the substrate to provide a plurality of n-type doped polysilicon regions among a plurality of p-type doped polysilicon regions.

Dual ohmic contact to N- and P-type silicon carbide

NASA Technical Reports Server (NTRS)

Okojie, Robert S. (Inventor)

2013-01-01

Simultaneous formation of electrical ohmic contacts to silicon carbide (SiC) semiconductor having donor and acceptor impurities (n- and p-type doping, respectively) is disclosed. The innovation provides for ohmic contacts formed on SiC layers having n- and p-doping at one process step during the fabrication of the semiconductor device. Further, the innovation provides a non-discriminatory, universal ohmic contact to both n- and p-type SiC, enhancing reliability of the specific contact resistivity when operated at temperatures in excess of 600.degree. C.

Ultra-thin ohmic contacts for p-type nitride light emitting devices

DOEpatents

Raffetto, Mark; Bharathan, Jayesh; Haberern, Kevin; Bergmann, Michael; Emerson, David; Ibbetson, James; Li, Ting

2014-06-24

A flip-chip semiconductor based Light Emitting Device (LED) can include an n-type semiconductor substrate and an n-type GaN epi-layer on the substrate. A p-type GaN epi-layer can be on the n-type GaN epi-layer and a metal ohmic contact p-electrode can be on the p-type GaN epi-layer, where the metal ohmic contact p-electrode can have an average thickness less than about 25 .ANG.. A reflector can be on the metal ohmic contact p-electrode and a metal stack can be on the reflector. An n-electrode can be on the substrate opposite the n-type GaN epi-layer and a bonding pad can be on the n-electrode.

Photometric study of the W UMa eclipsing binaries VW LMi and BX Dra

NASA Astrophysics Data System (ADS)

Sánchez-Bajo, F.; García-Melendo, E.; Gómez-Forrellad, J. M.

2007-12-01

New ephemeris and the absolute parameters—masses, radii and luminosities—of the contact systems VW LMi and BX Dra have been obtained, by means of the analysis of the minima data available in the literature (for the determination of the ephemeris) and combining the previously published spectroscopic information and the results of the Wilson-Devinney method using photometric data (for the determination of the absolute parameters). The VW LMi O- C analysis confirms the multiplicity of the system detected previously from the spectroscopic data. Masses of the VW LMi contact system primary and secondary components are 1.67 ± 0.02 M ⊙ and 0.70 ± 0.02 M ⊙, respectively. The corresponding radii are 1.709 ± 0.007 R ⊙ and 1.208 ± 0.006 R ⊙, respectively. For the BX Dra contact system the masses are 2.19 ± 0.13 M ⊙ and 0.63 ± 0.06 M ⊙, and the radii, 2.13 ± 0.04 R ⊙ and 1.26 ± 0.03 R ⊙, for the primary and secondary, respectively. In both cases, the estimated luminosities seem to be slightly greater that the values derived from the Hipparcos distances.

Contribution of Primordial Binary Evolution to the Two Blue-straggler Sequences in Globular Cluster M30

NASA Astrophysics Data System (ADS)

Jiang, Dengkai; Chen, Xuefei; Li, Lifang; Han, Zhanwen

2017-11-01

Two blue-straggler sequences discovered in globular cluster M30 provide a strong constraint on the formation mechanisms of blue stragglers. We study the formation of blue-straggler binaries through binary evolution, and find that binary evolution can contribute to the blue stragglers in both of the sequences. Whether a blue-straggler is located in the blue sequence or red sequence depends on the contribution of the mass donor to the total luminosity of the binary, which is generally observed as a single star in globular clusters. The blue stragglers in the blue sequence have a cool white dwarf companion, while the majority (˜60%) of the objects in the red sequence are binaries that are still experiencing mass transfer. However, there are also some objects for which the donors have just finished the mass transfer (the stripped-core stars, ˜10%) or the blue stragglers (the accretors) have evolved away from the blue sequence (˜30%). Meanwhile, W UMa contact binaries found in both sequences may be explained by various mass ratios, that is, W UMa contact binaries in the red sequence have two components with comparable masses (e.g., mass ratio q ˜ 0.3-1.0), while those in the blue sequence have low mass ratios (e.g., q< 0.3). However, the fraction of the blue sequence in M30 cannot be reproduced by binary population synthesis if we assumed the initial parameters of a binary sample to be the same as those of the field. This possibly indicates that dynamical effects on binary systems are very important in globular clusters.

Fabrication of back-contacted silicon solar cells using thermomigration to create conductive vias

DOEpatents

Gee, James M; Schmit, Russell R.

2007-01-30

Methods of manufacturing back-contacted silicon solar cells fabricated using a gradient-driven solute transport process, such as thermomigration or electromigration, to create n-type conductive vias connecting the n-type emitter layer on the front side to n-type ohmic contacts located on the back side.

Effects of different computer typing speeds on acceleration and peak contact pressure of the fingertips during computer typing.

PubMed

Yoo, Won-Gyu

2015-01-01

[Purpose] This study showed the effects of different computer typing speeds on acceleration and peak contact pressure of the fingertips during computer typing. [Subjects] Twenty-one male computer workers voluntarily consented to participate in this study. They consisted of 7 workers who could type 200-300 characteristics/minute, 7 workers who could type 300-400 characteristics/minute, and 7 workers who could type 400-500 chracteristics/minute. [Methods] This study was used to measure the acceleration and peak contact pressure of the fingertips for different typing speed groups using an accelerometer and CONFORMat system. [Results] The fingertip contact pressure was increased in the high typing speed group compared with the low and medium typing speed groups. The fingertip acceleration was increased in the high typing speed group compared with the low and medium typing speed groups. [Conclusion] The results of the present study indicate that a fast typing speed cause continuous pressure stress to be applied to the fingers, thereby creating pain in the fingers.

Method of fabricating a back-contact solar cell and device thereof

DOEpatents

Li, Bo; Smith, David; Cousins, Peter

2014-07-29

Methods of fabricating back-contact solar cells and devices thereof are described. A method of fabricating a back-contact solar cell includes forming an N-type dopant source layer and a P-type dopant source layer above a material layer disposed above a substrate. The N-type dopant source layer is spaced apart from the P-type dopant source layer. The N-type dopant source layer and the P-type dopant source layer are heated. Subsequently, a trench is formed in the material layer, between the N-type and P-type dopant source layers.

Method of fabricating a back-contact solar cell and device thereof

DOEpatents

Li, Bo; Smith, David; Cousins, Peter

2016-08-02

Methods of fabricating back-contact solar cells and devices thereof are described. A method of fabricating a back-contact solar cell includes forming an N-type dopant source layer and a P-type dopant source layer above a material layer disposed above a substrate. The N-type dopant source layer is spaced apart from the P-type dopant source layer. The N-type dopant source layer and the P-type dopant source layer are heated. Subsequently, a trench is formed in the material layer, between the N-type and P-type dopant source layers.

Contact urticaria, allergic contact dermatitis, and photoallergic contact dermatitis from oxybenzone.

PubMed

Landers, Maeran; Law, Sandra; Storrs, Frances J

2003-03-01

There is little literature regarding conventional patch tests and photopatch tests to oxybenzone resulting in both immediate- and delayed-type hypersensitivity reactions. A patient was patch-tested and photopatch-tested to various sunscreen chemicals. Both immediate- and delayed-type hypersensitivity reactions were observed with oxybenzone. The positive patch tests were also photoaccentuated. Oxybenzone, a common sunscreen allergen, can result in both contact urticaria and delayed-type hypersensitivity on both conventional patch testing and photopatch testing. Allergic contact dermatitis to sunscreen chemicals has traditionally included contact urticaria, allergic contact dermatitis, and photoallergic contact dermatitis. Due to the recognition of p-aminobenzoic acid (PABA) and its esters as sensitizers, the presence of benzophenones in "PABA-free" sunscreens has become more prevalent, especially in sunscreens with a sun protection factor (SPF) greater than 8. In our patient, immediate- and delayed-type hypersensitivity reactions were seen to oxybenzone (2-hydroxy-4-methoxybenzophenone, 2-benzoyl-5-methoxyphenol, benzophenone-3, Eusolex 4360, Escalol 567, EUSORB 228, Spectra-Sorb UV-9, Uvinul M-40) upon conventional patch testing and photopatch testing.

Distance of the contact glide in the closing masticatory stroke during mastication of three types of food.

PubMed

Rilo, B; Fernández-Formoso, N; Mora, M J; Cadarso-Suárez, C; Santana, U

2009-08-01

This study was designed to characterize the distance of the contact glide in the closing masticatory stroke in healthy adult subjects, during chewing of three types of food (crustless bread, chewing gum and peanuts). Mandibular movements (masticatory movements and laterality movements with dental contact) were registered using a gnathograph (MK-6I Diagnostic System) on the right and left side during unilateral chewing of the three food types. Length of dental contact was measured in masticatory cycle, which is defined as where the terminal part of the chewing cycles could be superimposed on the pathways taken by the mandible during lateral excursions with occlusal contacts. The length of dental contact during mastication of chewing gum is 1.46 +/- 1 mm, during chewing of soft bread is 1.38 +/- 0.7 mm and during chewing of peanuts is 1.45 +/- 0.9 mm. There is no significant difference in the lengths of dental contact during mastication of three types of foods that enable direct tooth gliding.

Effect of direct and indirect contact with mental illness on dangerousness and social distance.

PubMed

Lee, Minhwa; Seo, Mikyung

2018-03-01

This study is based on the contact hypothesis that contact with mental illness is the most effective anti-stigma strategy. This study aims to analyze which form of contact can most effectively decrease the dangerousness and social distance associated with schizophrenia, depression and alcoholism. In total, 573 Korean adults ( M age  = 43.71 years, standard deviation ( SD) = 13.41; 54.1% male, 45.9% female) were surveyed about randomly assigned vignettes of schizophrenia, depression and alcoholism. The participants were questioned on the dangerousness and social distance associated with the assigned vignette, as well as direct and indirect contact experience with the mental illness. Two-way analysis of variance (ANOVA) was used to determine the main effect and interaction effect that the type of mental illness and contact experience have on the two dependent variables (dangerousness and social distance). The findings show that the type of mental illness has a significant main effect on dangerousness and social distance, but contact type only has a significant main effect on social distance. Moreover, the two independent variables (mental illness subtype and contact experience) have an interaction effect on two dependent variables (dangerousness and social distance). Therefore, the anti-stigma effect of contact varies according to the type of mental illness. Our findings suggest that appropriate anti-stigma strategies are required for each type of mental illness. Considering that opportunities for direct contact with persons with mental illness are highly limited, it is necessary to actively utilize indirect contact.

Photometric study and absolute parameters of the short-period eclipsing binary HH Bootis

NASA Astrophysics Data System (ADS)

Gürol, B.; Bradstreet, D. H.; Demircan, Y.; Gürsoytrak, S. H.

2015-11-01

We present the results of our investigation on the geometrical and physical parameters of the W UMa type binary system HH Bootis from new CCD (BVRI) light curves and published radial velocity data. The photometric data were obtained in 2011 and 2012 at Ankara University Observatory (AUO). Light and radial velocity observations were analyzed simultaneously using the Wilson-Devinney (2013 revision) code to obtain absolute and geometrical parameters. The system was determined to be a W-type W UMa system of a type different from that suggested by Dal and Sipahi (2013). An interesting cyclic period variation in the time intervals between primary and secondary eclipses ("half-period variation") was discovered and analyzed and its possible cause is discussed. Combining our photometric solution with the spectroscopic data we derived masses and radii of the eclipsing system to be M1 = 0.627M⊙ , M2 = 1.068M⊙ , R1 = 0.782R⊙ and R2 = 0.997R⊙ . New light elements were derived and finally the evolutionary status of the system is discussed.

Nano-scaled Pt/Ag/Ni/Au contacts on p-type GaN for low contact resistance and high reflectivity.

PubMed

Kwon, Y W; Ju, I C; Kim, S K; Choi, Y S; Kim, M H; Yoo, S H; Kang, D H; Sung, H K; Shin, K; Ko, C G

2011-07-01

We synthesized the vertical-structured LED (VLED) using nano-scaled Pt between p-type GaN and Ag-based reflector. The metallization scheme on p-type GaN for high reflectance and low was the nano-scaled Pt/Ag/Ni/Au. Nano-scaled Pt (5 A) on Ag/Ni/Au exhibited reasonably high reflectance of 86.2% at the wavelength of 460 nm due to high transmittance of light through nano-scaled Pt (5 A) onto Ag layer. Ohmic behavior of contact metal, Pt/Ag/Ni/Au, to p-type GaN was achieved using surface treatments of p-type GaN prior to the deposition of contact metals and the specific contact resistance was observed with decreasing Pt thickness of 5 A, resulting in 1.5 x 10(-4) ohms cm2. Forward voltages of Pt (5 A)/Ag/Ni contact to p-type GaN showed 4.19 V with the current injection of 350 mA. Output voltages with various thickness of Pt showed the highest value at the smallest thickness of Pt due to its high transmittance of light onto Ag, leading to high reflectance. Our results propose that nano-scaled Pt/Ag/Ni could act as a promising contact metal to p-type GaN for improving the performance of VLEDs.

Contact Dermatitis in Pediatrics.

PubMed

Pelletier, Janice L; Perez, Caroline; Jacob, Sharon E

2016-08-01

Contact dermatitis is an umbrella term that describes the skin's reaction to contacted noxious or allergenic substances. The two main categories of contact dermatitis are irritant type and allergic type. This review discusses the signs, symptoms, causes, and complications of contact dermatitis. It addresses the testing, treatment, and prevention of contact dermatitis. Proper management of contact dermatitis includes avoidance measures for susceptible children. Implementation of a nickel directive (regulating the use of nickel in jewelry and other products that come into contact with the skin) could further reduce exposure to the most common allergens in the pediatric population. [Pediatr Ann. 2016;45(8):e287-e292.]. Copyright 2016, SLACK Incorporated.

Post-Cam Design and Contact Stress on Tibial Posts in Posterior-Stabilized Total Knee Prostheses: Comparison Between a Rounded and a Squared Design.

PubMed

Watanabe, Toshifumi; Koga, Hideyuki; Horie, Masafumi; Katagiri, Hiroki; Sekiya, Ichiro; Muneta, Takeshi

2017-12-01

The post-cam mechanism in posterior stabilized (PS) prostheses plays an important role in total knee arthroplasty (TKA). The purpose of this study is to clarify the difference of the contact stress on the tibial post between a rounded post-cam design and a squared design during deep knee flexion and at hyperextension using the three-dimensional (3D) finite element models. We created 2 types of 3D, finite element models of PS prostheses (types A and B), whose surfaces were identical except for the post-cam geometries: type A has a rounded post-cam design, while type B has a squared design. Both types have a similar curved-shape intercondylar notch of the femoral component. Stress distributions, peak contact stresses, and contact areas on the tibial posts at 90°, 120°, and 150° flexion with/without 10° tibial internal rotation and at 10° hyperextension were compared between the 2 models. Type B demonstrated more concentrated stress distribution compared to type A. The peak contact stresses were similar in both groups during neutral flexion; however, the stresses were much higher in type B during flexion with 10° rotation and at hyperextension. The higher peak contact stresses corresponded to the smaller contact areas in the tibial post. A rounded post-cam design demonstrated less stress concentration during flexion with rotation and at hyperextension compared with a squared design. The results would be useful for development of implant designs and prediction of the contact stress on the tibial post in PS total knee arthroplasty. Copyright © 2017 Elsevier Inc. All rights reserved.

Single nucleotide polymorphism-based molecular typing of M. leprae from multicase families of leprosy patients and their surroundings to understand the transmission of leprosy.

PubMed

Turankar, R P; Lavania, M; Chaitanya, V S; Sengupta, U; Darlong, J; Darlong, F; Siva Sai, K S R; Jadhav, R S

2014-03-01

The exact mode of transmission of leprosy is not clearly understood; however, many studies have demonstrated active transmission of leprosy around a source case. Families of five active leprosy cases and their household contacts were chosen from a high endemic area in Purulia. Fifty-two soil samples were also collected from different areas of their houses. DNA was extracted from slit-skin smears (SSS) and soil samples and the Mycobacterium leprae-specific RLEP (129 bp) region was amplified using PCR. Molecular typing of M. leprae was performed for all RLEP PCR-positive samples by single nucleotide polymorphism (SNP) typing and confirmation by DNA sequencing. SSS of these five patients and six out of the total 28 contacts were PCR positive for RLEP whereas 17 soil samples out of 52 showed the presence of M. leprae DNA. SNP typing of M. leprae from all RLEP PCR-positive subjects (patients and smear-positive contacts) and 10 soil samples showed the SNP type 1 genotype. M. leprae DNA from the five leprosy patients and the six contacts was further subtyped and the D subtype was noted in all patients and contacts, except for one contact where the C subtype was identified. Typing followed by subtyping of M. leprae clearly revealed that either the contacts were infected by the patients or both patients and contacts had the same source of infection. It also revealed that the type of M. leprae in the soil in the inhabited areas where patients resided was also of the same type as that found in patients. © 2013 The Authors Clinical Microbiology and Infection © 2013 European Society of Clinical Microbiology and Infectious Diseases.

Effect of reflective p-type ohmic contact on thermal reliability of vertical InGaN/GaN LEDs

NASA Astrophysics Data System (ADS)

Son, Jun Ho; Song, Yang Hee; Kim, Buem Joon; Lee, Jong-Lam

2014-11-01

We report on the enhanced thermal reliability of vertical-LEDs (VLEDs) using novel reflective p-type ohmic contacts with good thermal stability. The reflective p-type ohmic contacts with Ni/Ag-Cu alloy multi-layer structure shows low contact resistivity, as low as 9.3 × 10-6 Ωcm2, and high reflectance of 86% after annealing at 450°C. The V-LEDs with Ni/Ag-Cu alloy multi-layer structure show good thermal reliability with stress time at 300°C in air ambient. The improved thermal stability of the reflective ohmic contacts to p-type GaN is believed to play a critical role in the thermal reliability of V-LEDs. [Figure not available: see fulltext.

The effects of two different types of bandage contact lenses on the healthy canine eye.

PubMed

Braus, Barbara Katharina; Riedler, Daniela; Tichy, Alexander; Spergser, Joachim; Schwendenwein, Ilse

2018-02-06

To compare two types of bandage contact lenses on the healthy canine eye. Six healthy Beagles. Two different types of bandage contact lenses (single sized human silicone contact lens 'PureVision 2' (Bausch & Lomb Incorporated, Rochester, NY, USA) and specially designed veterinary hydrogel contact lens 'AcriVet Pat D' (Bausch & Lomb Incorporated) were placed in 12 eyes of healthy Beagle dogs. Retention times and the effects of the lenses regarding irritation of the eye, changes in tear production, impact of contact lenses on tonometric readings, and cytologic and microbiological alterations of the canine eye were investigated. Mean retention times for veterinary hydrogel lenses with special dimensions were significantly shorter (2 days) than for one size human silicon lenses (8.8 days). Irritation scores were overall low for both types of lenses apart from one human lens causing severe irritation and keratoconjunctivitis as a sequel to folding and displacement. Tear production remained stable in human contact lenses. Intraocular pressure readings with a contact lens in place were only slightly altered; the most accurate readings were obtained through a human lens with an applanation tonometer. Cytology revealed a slight, nonsignificant increase in neutrophilic granulocytes with both types of lenses; the microflora did not change significantly. Human silicone lenses have significantly longer retention times and are less expensive than veterinary hydrogel lenses. In regard to irritation, bacterial growth and inflammation, both types of lenses can be recommended for use in canine eyes. © 2018 American College of Veterinary Ophthalmologists.

Out-of-plane strain and electric field tunable electronic properties and Schottky contact of graphene/antimonene heterostructure

NASA Astrophysics Data System (ADS)

Phuc, Huynh V.; Hieu, Nguyen N.; Hoi, Bui D.; Phuong, Le T. T.; Hieu, Nguyen V.; Nguyen, Chuong V.

2017-12-01

In this paper, the electronic properties of graphene/monolayer antimonene (G/m-Sb) heterostructure have been studied using the density functional theory (DFT). The effects of out-of-plane strain (interlayer coupling) and electric field on the electronic properties and Schottky contact of the G/m-Sb heterostructure are also investigated. The results show that graphene is bound to m-Sb layer by a weak van-der-Waals interaction with the interlayer distance of 3.50 Å and the binding energy per carbon atom of -39.62 meV. We find that the n-type Schottky contact is formed at the G/m-Sb heterostructure with the Schottky barrier height (SBH) of 0.60 eV. By varying the interlayer distance between graphene and the m-Sb layer we can change the n-type and p-type SBH at the G/m-Sb heterostructure. Especially, we find the transformation from n-type to p-type Schottky contact with decreasing the interlayer distance. Furthermore, the SBH and the Schottky contact could be controlled by applying the perpendicular electric field. With the positive electric field, electrons can easily transfer from m-Sb to graphene layer, leading to the transition from n-type to p-type Schottky contact.

Social contact patterns can buffer costs of forgetting in the evolution of cooperation.

PubMed

Stevens, Jeffrey R; Woike, Jan K; Schooler, Lael J; Lindner, Stefan; Pachur, Thorsten

2018-06-13

Analyses of the evolution of cooperation often rely on two simplifying assumptions: (i) individuals interact equally frequently with all social network members and (ii) they accurately remember each partner's past cooperation or defection. Here, we examine how more realistic, skewed patterns of contact-in which individuals interact primarily with only a subset of their network's members-influence cooperation. In addition, we test whether skewed contact patterns can counteract the decrease in cooperation caused by memory errors (i.e. forgetting). Finally, we compare two types of memory error that vary in whether forgotten interactions are replaced with random actions or with actions from previous encounters. We use evolutionary simulations of repeated prisoner's dilemma games that vary agents' contact patterns, forgetting rates and types of memory error. We find that highly skewed contact patterns foster cooperation and also buffer the detrimental effects of forgetting. The type of memory error used also influences cooperation rates. Our findings reveal previously neglected but important roles of contact pattern, type of memory error and the interaction of contact pattern and memory on cooperation. Although cognitive limitations may constrain the evolution of cooperation, social contact patterns can counteract some of these constraints. © 2018 The Author(s).

The modulation of Schottky barriers of metal-MoS2 contacts via BN-MoS2 heterostructures.

PubMed

Su, Jie; Feng, Liping; Zhang, Yan; Liu, Zhengtang

2016-06-22

Using first-principles calculations within density functional theory, we systematically studied the effect of BN-MoS2 heterostructure on the Schottky barriers of metal-MoS2 contacts. Two types of FETs are designed according to the area of the BN-MoS2 heterostructure. Results show that the vertical and lateral Schottky barriers in all the studied contacts, irrespective of the work function of the metal, are significantly reduced or even vanish when the BN-MoS2 heterostructure substitutes the monolayer MoS2. Only the n-type lateral Schottky barrier of Au/BN-MoS2 contact relates to the area of the BN-MoS2 heterostructure. Notably, the Pt-MoS2 contact with n-type character is transformed into a p-type contact upon substituting the monolayer MoS2 by a BN-MoS2 heterostructure. These changes of the contact natures are ascribed to the variation of Fermi level pinning, work function and charge distribution. Analysis demonstrates that the Fermi level pinning effects are significantly weakened for metal/BN-MoS2 contacts because no gap states dominated by MoS2 are formed, in contrast to those of metal-MoS2 contacts. Although additional BN layers reduce the interlayer interaction and the work function of the metal, the Schottky barriers of metal/BN-MoS2 contacts still do not obey the Schottky-Mott rule. Moreover, different from metal-MoS2 contacts, the charges transfer from electrodes to the monolayer MoS2, resulting in an increment of the work function of these metals in metal/BN-MoS2 contacts. These findings may prove to be instrumental in the future design of new MoS2-based FETs with ohmic contact or p-type character.

Germanium- and tellurium-doped GaAs for non-alloyed p-type and n-type ohmic contacts

NASA Astrophysics Data System (ADS)

Park, Joongseo; Barnes, Peter A.; Lovejoy, Michael L.

1995-08-01

Epitaxial ohmic contacts to GaAs were grown by liquid phase epitaxy. Heavily Ge-doped GaAs was grown to prepare ohmic contacts to p-GaAs while Te was used for the n-type contacts. Hall measurements were carried out for the samples grown from melts in which the mole fraction of Ge was varied between 1.55 atomic % and 52.2 atomic %, while the Te mole fractions varied between 0.03% and 0.5%. Specific contact resistance, rc, as low as rcp=2.9×10-6 ohm-cm 2 for Ge doping of p=(Na-Nd)=6.0×1019 holes/cm3 was measured for p-contacts and rcn=9.6×10-5 ohm-cm2 was measured for Te doping of n=(Nd-Na)=8.9×1018 electrons/cm3 for GaAs metallized with non-alloyed contacts of Ti/Al.

Method of forming contacts for a back-contact solar cell

DOEpatents

Manning, Jane

2015-10-20

Methods of forming contacts for solar cells are described. In one embodiment, a method includes forming a silicon layer above a substrate, forming and patterning a solid-state p-type dopant source on the silicon layer, forming an n-type dopant source layer over exposed regions of the silicon layer and over a plurality of regions of the solid-state p-type dopant source, and heating the substrate to provide a plurality of n-type doped silicon regions among a plurality of p-type doped silicon regions.

Method of forming contacts for a back-contact solar cell

DOEpatents

Manning, Jane

2014-07-15

Methods of forming contacts for solar cells are described. In one embodiment, a method includes forming a silicon layer above a substrate, forming and patterning a solid-state p-type dopant source on the silicon layer, forming an n-type dopant source layer over exposed regions of the silicon layer and over a plurality of regions of the solid-state p-type dopant source, and heating the substrate to provide a plurality of n-type doped silicon regions among a plurality of p-type doped silicon regions.

Holding the baby: early mother-infant contact after childbirth and outcomes.

PubMed

Redshaw, Maggie; Hennegan, Julie; Kruske, Sue

2014-05-01

to describe the timing, type and duration of initial infant contact and associated demographic and clinical factors in addition to investigating the impact of early contact on breastfeeding and maternal health and well being after birth. data from a recent population survey of women birthing in Queensland, Australia were used to describe the nature of the first hold and associated demographic characteristics. Initial comparisons, with subsequent adjustment for type of birthing facility and mode of childbirth, were used to assess associations between timing, type and duration of initial contact and outcomes. Further analyses were conducted to investigate a dose-response relationship between duration of first contact and outcomes. women who had an unassisted vaginal birth held their infant sooner, and for longer than women who had an assisted vaginal birth or caesarean and were more satisfied with their early contact. Multivariate models showed a number of demographic and clinical interventions contributing to timing, duration and type of first contact with type of birthing facility (public/private), area of residence, and assisted birth as prominent factors. For women who had a vaginal birth; early, skin-to-skin, and longer duration of initial contact were associated with high rates of breastfeeding initiation and breastfeeding at discharge, but not breastfeeding at 13 weeks. Some aspects of early contact were associated with improved maternal well being. However, these associations were not found for women who had a caesarean birth. With longer durations of first contact, a dose-response effect was found for breastfeeding. results of the study provide a description of current practice in Queensland, Australia and factors impacting on early contact. For vaginal births, findings add to the evidence in support of early skin-to-skin contact for an extended period. It is suggested that all research in this area should consider the effects of early contact separately for women having vaginal and caesarean births. care providers should consider extending the period of early contact in routine care following vaginal birth and explore the way in which women having a caesarean birth might be better supported in benefitting from early contact with their infant. Copyright © 2014. Published by Elsevier Ltd.

Design and application of ion-implanted polySi passivating contacts for interdigitated back contact c-Si solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Guangtao; Ingenito, Andrea; Hameren, Nienke van

2016-01-18

Ion-implanted passivating contacts based on poly-crystalline silicon (polySi) are enabled by tunneling oxide, optimized, and used to fabricate interdigitated back contact (IBC) solar cells. Both n-type (phosphorous doped) and p-type (boron doped) passivating contacts are fabricated by ion-implantation of intrinsic polySi layers deposited via low-pressure chemical vapor deposition and subsequently annealed. The impact of doping profile on the passivation quality of the polySi doped contacts is studied for both polarities. It was found that an excellent surface passivation could be obtained by confining as much as possible the implanted-and-activated dopants within the polySi layers. The doping profile in the polySimore » was controlled by modifying the polySi thickness, the energy and dose of ion-implantation, and the temperature and time of annealing. An implied open-circuit voltage of 721 mV for n-type and 692 mV for p-type passivating contacts was achieved. Besides the high passivating quality, the developed passivating contacts exhibit reasonable high conductivity (R{sub sh n-type} = 95 Ω/□ and R{sub sh p-type} = 120 Ω/□). An efficiency of 19.2% (V{sub oc} = 673 mV, J{sub sc} = 38.0 mA/cm{sup 2}, FF = 75.2%, and pseudo-FF = 83.2%) was achieved on a front-textured IBC solar cell with polySi passivating contacts as both back surface field and emitter. By improving the front-side passivation, a V{sub OC} of 696 mV was also measured.« less

Contact Lens Solutions and Contact Lens Discomfort: Examining the Correlations Between Solution Components, Keratitis, and Contact Lens Discomfort.

PubMed

Kuc, Christopher J; Lebow, Kenneth A

2018-06-13

This article will examine the current literature, as it relates to contact lens discomfort (CLD) secondary to contact lens solutions. The reader will better understand the characteristics of contact lenses, as they uniquely interact with each type of contact lens solution and also gain a better comprehension of the components of contact lens solution such as preservatives, surfactants, and chelating agents, which may contribute to discomfort. By investigating corneal staining theory and the mechanisms that contribute to its presence, the reader will gain insight into this clinical finding, which relates to selection of contact lens solutions. The FDA standards for testing solutions and how this relates to contact lens keratitis will also be appraised in regards to current ISO recommendations. Finally, better selection of multipurpose contact lens solution (MPS) and hydrogen peroxide-based solutions for patients should be accessible to the clinician based on this review and preexisting clinical findings or diagnoses. A review of current published literature from peer reviewed journals and online journals was conducted to gain an understanding of contact lens solution's impact on contact lens discomfort. Many studies have been conducted comparing comfort between various types of contact lens solutions. It is challenging to decipher this information and apply it clinically when selecting solutions for patients. By comparing solution components, how contact lens solutions interact with different types of lenses, keratitis related to contact lenses, and preexisting ocular conditions, this review will improve a clinician's ability to eliminate CLD.

Children of divorce: the differential diagnosis of contact refusal.

PubMed

Freeman, Bradley W

2011-07-01

Contact refusal is a common phenomenon that can occur during the course of, or after, divorce, which affects the relationship between a child and the parent. This article defines the concept of contact refusal and discusses the importance of its recognition. The concept is further narrowed to focus on the child as the one refusing contact, not the parent, which can happen as well. Various types of contact refusals are illustrated in the article through clinical vignettes, and an approach to categorizing the various types of contact refusal is presented. Copyright © 2011 Elsevier Inc. All rights reserved.

What we learn from eclipsing binaries in the ultraviolet

NASA Technical Reports Server (NTRS)

Guinan, Edward F.

1990-01-01

Recent results on stars and stellar physics from IUE (International Ultraviolet Explorer) observations of eclipsing binaries are discussed. Several case studies are presented, including V 444 Cyg, Aur stars, V 471 Tau and AR Lac. Topics include stellar winds and mass loss, stellar atmospheres, stellar dynamos, and surface activity. Studies of binary star dynamics and evolution are discussed. The progress made with IUE in understanding the complex dynamical and evolutionary processes taking place in W UMa-type binaries and Algol systems is highlighted. The initial results of intensive studies of the W UMa star VW Cep and three representative Algol-type binaries (in different stages of evolution) focused on gas flows and accretion, are included. The future prospects of eclipsing binary research are explored. Remaining problems are surveyed and the next challenges are presented. The roles that eclipsing binaries could play in studies of stellar evolution, cluster dynamics, galactic structure, mass luminosity relations for extra galactic systems, cosmology, and even possible detection of extra solar system planets using eclipsing binaries are discussed.

Photometric Study of The Solar Type, Total Eclipsing Binary, TYC 2853-18-1

NASA Astrophysics Data System (ADS)

Samec, Ronald G.; Figg, E. R.; Faulkner, D.; Van Hamme, W.

2009-12-01

We present an analysis of the Solar-Type eclipsing binary, TYC 2853-18-1 (Persei), based on observations taken at the National Undergraduate Research Observatory (NURO) and the Southeastern Association for Research in Astronomy (SARA) in the Fall, 2007 and Spring, 2008. Light curves, a period study and a synthetic light curve solution are presented for this variable which was recently discovered by TYCHO as an eclipsing binary (2006, IBVS 5700). Our CCD observations of TYC 2853-18-1 [GSC 2853 0018, RA(2000) = 02h 47m 07.996s, DEC(2000) = +41° 22’ 32.80"] were taken on 20,27 December, 2007 at Lowell Observatory with the 0.81-m reflector with NURO time and 25 November, 3 December, 2007 and 19 February, 2008 via remote observing from Kitt Peak with SARA. NURO observations were take with the thermoelectrically cooled (<-100C) 2KX2K CCD NASACAM. Standard BVRcIc Johnson-Cousins filters were used. Our light curve solution was calculated with the 2004 Wilson code. Mean times of eclipse include, HJDMinI = 2454516.6131(±0.0005), 2454440.52974(±0.00008), 2454438.7605 (±0.0001), 2454462.6464 (±0.0003), HJDMinII = 2454455.71985 (±0.00060), 255462.7943 (±0.0002). These, including the epoch by ROTSE (2006, IBVS 5699) and the epoch calculated by the Wilson code, yielded the following ephemeris: HJD Hel Min I =2451370.8753(±.0.0010)d + 0.2949039 (±0.0000001)E Our unspotted Wilson code solution reveals TYC 2853-18-1 to be a W-type W UMa contact binary with unequal eclipse depths (amplitudes are 0.72 and 0.61 mags in V). It has shallow contact (8% fill-out) and a brief, but total eclipse. Its curves dictate a mass ratio of 2.62±0.01, a component temperature difference of only 73±5 ° K and an inclination of 82.0±0.2°. Spot activity is indicated by night to night variations. We wish to thank the NURO and SARA for their allocation of observing time, as well as NASA and the AAS for their support in paying for travel and publication expenses.

Chromium Trioxide Hole-Selective Heterocontacts for Silicon Solar Cells.

PubMed

Lin, Wenjie; Wu, Weiliang; Liu, Zongtao; Qiu, Kaifu; Cai, Lun; Yao, Zhirong; Ai, Bin; Liang, Zongcun; Shen, Hui

2018-04-25

A high recombination rate and high thermal budget for aluminum (Al) back surface field are found in the industrial p-type silicon solar cells. Direct metallization on lightly doped p-type silicon, however, exhibits a large Schottky barrier for the holes on the silicon surface because of Fermi-level pinning effect. As a result, low-temperature-deposited, dopant-free chromium trioxide (CrO x , x < 3) with high stability and high performance is first applied in a p-type silicon solar cell as a hole-selective contact at the rear surface. By using 4 nm CrO x between the p-type silicon and Ag, we achieve a reduction of the contact resistivity for the contact of Ag directly on p-type silicon. For further improvement, we utilize a CrO x (2 nm)/Ag (30 nm)/CrO x (2 nm) multilayer film on the contact between Ag and p-type crystalline silicon (c-Si) to achieve a lower contact resistance (40 mΩ·cm 2 ). The low-resistivity Ohmic contact is attributed to the high work function of the uniform CrO x film and the depinning of the Fermi level of the SiO x layer at the silicon interface. Implementing the advanced hole-selective contacts with CrO x /Ag/CrO x on the p-type silicon solar cell results in a power conversion efficiency of 20.3%, which is 0.1% higher than that of the cell utilizing 4 nm CrO x . Compared with the commercialized p-type solar cell, the novel CrO x -based hole-selective transport material opens up a new possibility for c-Si solar cells using high-efficiency, low-temperature, and dopant-free deposition techniques.

Infectious disease transmission: survey of contacts between hospital-based healthcare workers and working adults from the general population.

PubMed

Jiang, Lili; Ng, Isabel Hui Leng; Hou, Yan'an; Li, Dunli; Tan, Linda Wei Lin; Ho, Hanley Jian An; Chen, Mark I-Cheng

2018-04-01

Healthcare workers (HCWs) may be the inadvertent interface between the healthcare setting and the community for infectious diseases transmission. To investigate HCWs' contacts during a work day and compare these against working adults from the general population. Prospective survey of contacts through 24 h self-reported diary in three public sector tertiary care hospitals and community-based working adults in Singapore. Participants were HCWs and working adults from the community. In all, 211 HCWs and 1028 working adults reported a total of 4066 and 9206 contacts. HCWs reported more work-related contacts than community-based working adults (median of 13 versus 4), and more contacts that were neither household nor work-related (1 versus 0) but fewer household contacts (2 versus 3). HCWs reported more work-related contacts involving physical contacts, and more new contacts particularly with short duration (≤15 min) compared to community-based working adults. Among different HCW types, doctors reported the highest whereas ward-based nurses reported the lowest total work-related contacts. Around half of ward-based and clinic-based nurses' contacts involved physical touch. Work-related contacts reported by clinic-based nurses, doctors, and assorted HCWs were shorter than in ward-based nurses, with a substantial number effectively occurring with new contacts. Institutional effects significant on univariate analyses were much reduced and non-significant after adjusting for confounding by HCW type. HCWs' contacts differ substantially from those of community-based working adults. HCWs may thus be at higher risk of acquiring and spreading contact-transmissible and respiratory infections due to the nature of their work. Whereas total number of contacts was fairly similar between HCW types, the characteristics of their contacts differed substantively. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Chromospheric activity on late-type star DM UMa using high-resolution spectroscopic observations

NASA Astrophysics Data System (ADS)

Zhang, LiYun; Pi, QingFeng; Han, Xianming L.; Chang, Liang; Wang, Daimei

2016-06-01

We present new 14 high-resolution echelle spectra to discuss the level of chromospheric activity of DM UMa in {He I} D3, {Na I} D1, D2, Hα, and {Ca II} infrared triplet lines (IRT). It is the first time to discover the emissions above the continuum in the {He I} D3 lines on 2015 February 9 and 10. The emission on February 9 is the strongest one ever detected for DM UMa. We analysed these chromospheric active indicators by employing the spectral subtraction technique. The subtracted spectra reveal weak emissions in the {Na I} D1, D2 lines, strong emission in the Hα line, and clear excess emissions in the {Ca II} IRT lines. Our values for the EW8542/EW8498 ratio are on the low side, in the range of 1.0-1.7. There are also clear phase variations of the level of chromospheric activity in equivalent width (EW) light curves in these chromospheric active lines (especially the Hα line). These phenomena might be explained by flare events or rotational modulations of the level of chromospheric activity.

Investigation of aluminium ohmic contacts to n-type GaN grown by molecular beam epitaxy

NASA Astrophysics Data System (ADS)

Kribes, Y.; Harrison, I.; Tuck, B.; Kim, K. S.; Cheng, T. S.; Foxon, C. T.

1997-11-01

Using epi-layers of different doping concentrations, we have investigated aluminium contacts on n-type gallium nitride grown by plasma source molecular beam epitaxy. To achieve repeatable and reliable results it was found that the semiconductor needed to be etched in aqua-regia before the deposition of the contact metallization. Scanning electron micrographs of the semiconductor surface show a deterioration of the semiconductor surface on etching. The specific contact resistivity of the etched samples were, however, superior. Annealing the contacts at 0268-1242/12/11/030/img9 produced contacts with the lowest specific contact resistance of 0268-1242/12/11/030/img10. The long-term aging of these contacts was also investigated. The contacts and the sheet resistance were both found to deteriorate over a three-month period.

Occupant-to-occupant contact injury in motor vehicle crashes.

PubMed

Viano, David C; Parenteau, Chantal S

2017-10-03

This is a descriptive study of the frequency and risk of occupant-to-occupant contact injury by crash type and occupant age. It focused on rear impacts because of a recent Senate inquiry. 1994-2013 NASS-CDS data were used to investigate the effects of occupant-to-occupant contact on the risk of serious-to-fatal injury (Abbreviated Injury Scale [AIS] 3+) by crash type and age group. NASS-CDS in-depth cases were analyzed to identify crash circumstances for AIS 3+ occupant-to-occupant contact injury in rear crashes. Serious injury (AIS 3+) due to occupant-to-occupant contact was uncommon. It represented only 0.84% of all AIS 3+ injury for all age groups. The overall risk of AIS 3+ occupant-to-occupant contact injury was 0.042 ± 0.007%. The highest incidence was in side impacts (69.8%) followed by rollovers (22.9%). Occupant-to-occupant contact injury risk was lower in rear impacts than in other crash types, at 0.0078 ± 0.0054%. The highest risk of AIS 3+ injury with occupant-to-occupant was for the <9-year-old age group when compared to other age groups for all crash types. The risk was 0.051 ± 0.026%, representing 2.69% of all AIS 3+ injury in the <9-year-old age group. Only 4.2% of AIS 3+ occupant-to-occupant contact injury occurred to children <9 years old in rear impacts. The corresponding injury risk was lowest in rear impacts, at 0.014 ± 0.014%%, when compared to other crash types. The analysis of in-depth NASS-CDS cases of occupant-to-occupant contact injury in children< 9 years old involved in rear impacts identified very severe collisions in older model vehicles with deformation of the occupant compartment and yielding front seats as main factors for the contact injury. Front seat occupants injuring rear-seated children was not identified in the in-depth NASS-CDS cases. AIS 3+ occupant-to-occupant contact injury occurs primarily in side impacts and rollovers. Most contact injury is to adults (89.4% incidence). Occupant-to-occupant contact injury to children is rare in rear impacts.

Encapsulant Characterization and Doped Passivated Contacts for Use in a Luminescent Solar Concentrator

NASA Astrophysics Data System (ADS)

Fogel, Derek

We report progress towards encapsulant characterization and the fabrication of passivated interdigitated back contact silicon solar cells using spin-on dopants for use in a luminescent solar concentrator. For the luminescent solar concentrator to be successful, the encapsulants used to assemble the final device must not contribute to optical losses and the tandem cell must exhibit excellent passivation and low contact resistivity values. The index of refraction of polydimethylsiloxane (PDMS) is calculated to be 1.405-1.415 for 600-800 nm and 1.475-1.505 is calculated for ethylene vinyl acetate (EVA). The absorption coefficient is calculated to be less than 0.1 cm-1 for PDMS and less than 0.5 cm-1 for EVA at wavelengths less than 1000 nm. Polysilicon / SiOx passivated contact symmetric structures grown using plasma-enhanced chemical vapor deposition (PECVD) and low pressure chemical vapor deposition (LPCVD) and subsequently doped using P, B, and Ga spin-on dopants are fabricated, and their passivation and contact properties are analyzed. The n-type, P-doped passivated contact gives an implied open circuit voltage (iVOC) of 708 mV in PECVD and 727 mV in LPCVD. The p-type, B-doped passivated contact gives an iVOC of 667 mV in PECVD and 689 mV in LPCVD. The p-type, Ga-doped passivated contact, which has not been previously reported, gives an iVOC of 731 mV in PECVD and 714 mV in LPCVD. For the n-type, P-doped contact a low metal to polysilicon contact resistivity of 23.8 mO-cm2 was measured for Al on PECVD and 15.8 mO-cm2 was measured for Al on LPCVD. For the p-type, B-doped contact a low metal to polysilicon contact resistivity of 0.3 mO-cm2 was measured for Al on LPCVD. These results are encouraging for the processing of passivated interdigitated back contact solar cells, and present a route towards high-efficiency Si PV at low cost.

Handling times and saturating transmission functions in a snail-worm symbiosis.

PubMed

Hopkins, Skylar R; McGregor, Cari M; Belden, Lisa K; Wojdak, Jeremy M

2018-06-16

All dynamic species interaction models contain an assumption that describes how contact rates scale with population density. Choosing an appropriate contact-density function is important, because different functions have different implications for population dynamics and stability. However, this choice can be challenging, because there are many possible functions, and most are phenomenological and thus difficult to relate to underlying ecological processes. Using one such phenomenological function, we described a nonlinear relationship between field transmission rates and host density in a common snail-oligochaete symbiosis. We then used a well-known contact function from predator-prey models, the Holling Type II functional response, to describe and predict host snail contact rates in the laboratory. The Holling Type II functional response accurately described both the nonlinear contact-density relationship and the average contact duration that we observed. Therefore, we suggest that contact rates saturate with host density in this system because each snail contact requires a non-instantaneous handling time, and additional possible contacts do not occur during that handling time. Handling times and nonlinear contact rates might also explain the nonlinear relationship between symbiont transmission and snail density that we observed in the field, which could be confirmed by future work that controls for other potential sources of seasonal variation in transmission rates. Because most animal contacts are not instantaneous, the Holling Type II functional response might be broadly relevant to diverse host-symbiont systems.

Ohmic contacts for laser diodes

NASA Technical Reports Server (NTRS)

Ladany, I.; Marinelli, D. P.

1983-01-01

Requirements for ohmic contacts to laser diodes are discussed, and properties of Schottky barrier tunneling contacts are reviewed. A procedure is described for measuring contact resistance on fabricated laser material without the need for specially constructed samples and contact configurations. Measurements of contact resistance and estimates of specific contact resistance are given for Ti/Pt/Au contacts to surfaces with three different doping levels. It was found that below a p-type carrier concentration of 1 x 10 to the 19th per cu cm the contact resistance is likely to be too high for good device performance. At higher doping levels, a specific contact resistance as low as 2 x 10 to the -6th ohm sq cm was obtained. Oxide stripe lasers provided with the type of contact discussed in this paper have been operated without failures for periods up to 7 years at a current density at the contact of 6-8 kA/sq cm. It appears therefore that these contacts satisfy the need for low resistance and durability and that, at the same time, they do not cause any obvious material degradation.

Carrier Selective, Passivated Contacts for High Efficiency Silicon Solar Cells based on Transparent Conducting Oxides

DOE PAGES

Young, David L.; Nemeth, William; Grover, Sachit; ...

2014-01-01

We describe the design, fabrication and results of passivated contacts to n-type silicon utilizing thin SiO 2 and transparent conducting oxide layers. High temperature silicon dioxide is grown on both surfaces of an n-type wafer to a thickness <50 Å, followed by deposition of tin-doped indium oxide (ITO) and a patterned metal contacting layer. As deposited, the thin-film stack has a very high J0, contact, and a non-ohmic, high contact resistance. However, after a forming gas anneal, the passivation quality and the contact resistivity improve significantly. The contacts are characterized by measuring the recombination parameter of the contact (J0, contact)more » and the specific contact resistivity (ρ contact) using a TLM pattern. The best ITO/SiO 2 passivated contact in this study has J 0,contact = 92.5 fA/cm 2 and ρ contact = 11.5 mOhm-cm 2. These values are placed in context with other passivating contacts using an analysis that determines the ultimate efficiency and the optimal area fraction for contacts for a given set of (J0, contact, ρ contact) values. The ITO/SiO 2 contacts are found to have a higher J0, contact, but a similar ρ contact compared to the best reported passivated contacts.« less

Allergic Skin Conditions

MedlinePlus

... most common types are atopic dermatitis (often called eczema) and contact dermatitis. Atopic Dermatitis (Eczema) Eczema is a chronic ... contact with your skin, they may cause a rash called contact dermatitis. There are two kinds of contact dermatitis: ...

First Precision Photometric Observations and Analyses of The Totally Eclipsing, Solar Type Binary, V573 Pegasi

NASA Astrophysics Data System (ADS)

Samec, Ronald G.; Caton, Daniel B.; Faulkner, Danny R.

2018-06-01

CCD, VRI light curves of V573 Peg were taken in 26,27 September and 2, 4 and 6 October, 2017 at the Dark Sky Observatory in North Carolina with the 0.81-m reflector of Appalachian State University by D. Caton. V573 Peg was discovered by the SAVS survey which classified it as a V= 0.51 amplitude, EW variable. They included a rough spectrum identifying the binary was about a type G, although the period would indicate it is an F-type contact binary. Five times of minimum light were calculated, two primary eclipses and three secondary, from our present observations:HJD I = 2458023.6420±0.0012, 2458028.6522±0.0021,HJD II = 2458022.5991±0.0011, 2458023.8510±0.0010 and 2458028.8608±0.0005,The following linear and quadratic ephemerides were determined from all available times of minimum light.JD Hel MinI = 2456876.49437±0.00078d + 0.41745021±0. 00000017 × E, -JD Hel MinI = 2456876.49580±0.00023d + 0. 417448601±0.000000083× E - 0.000000000274±0.000000000012 X E2A 14-year period study (24 times of minimum light) revealed that the orbital period decreasing with a high level of confidence, possibly due to magnetic braking. The mass ratio is found to be somewhat extreme, M2/M1=0.2629±0.0006.Its Roche Lobe fill-out is 25%. The solution had no need of spots. The temperature difference of the components is about ~130 K, with the secondary as the hotter star, so it is a W-type W UMa Binary. The inclination is 80.4±0.1° . The secondary eclipse shows a time of constant light with an eclipse duration of 24 minutes. More details of our results will be given at the meeting.

Large area tunnel oxide passivated rear contact n -type Si solar cells with 21.2% efficiency: Large area tunnel oxide passivated rear contact n -type Si solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tao, Yuguo; Upadhyaya, Vijaykumar; Chen, Chia-Wei

This paper reports on the implementation of carrier-selective tunnel oxide passivated rear contact for high-efficiency screen-printed large area n-type front junction crystalline Si solar cells. It is shown that the tunnel oxide grown in nitric acid at room temperature (25°C) and capped with n+ polysilicon layer provides excellent rear contact passivation with implied open-circuit voltage iVoc of 714mV and saturation current density J0b of 10.3 fA/cm2 for the back surface field region. The durability of this passivation scheme is also investigated for a back-end high temperature process. In combination with an ion-implanted Al2O3-passivated boron emitter and screen-printed front metal grids,more » this passivated rear contact enabled 21.2% efficient front junction Si solar cells on 239 cm2 commercial grade n-type Czochralski wafers.« less

Allergic manifestations of contact lens wearing.

PubMed

Solomon, Abraham

2016-10-01

Contact lens-induced papillary conjunctivitis (CLPC) is a common ocular allergic disease in contact lens wearers. In its more severe form, it can cause giant papillary conjunctivitis, resulting in contact lens intolerance and the need to discontinue the use of contact lenses. This review presents the pathogenesis, clinical manifestations and management guidelines of this common disorder. Different types of contact lenses are associated with differences in the severity of CLPC. Refitting patients with silicone hydrogel contact lenses or with daily disposable contact lenses may improve the signs and symptoms of CLPC. The recent introduction of the topical immunomodulatory agent tacrolimus in other severe allergic eye diseases may apply in suppressing the allergic inflammation in CLPC as well. CLPC is a common ocular disorder in contact lens wearers, with a significant impact on the quality of vision. It should be promptly recognized by healthcare practitioners and managed by modifications of the types and wearing schedules of contact lenses, as well as novel treatment options with topical immunomodulators.

The effect of trochlear dysplasia on patellofemoral biomechanics: a cadaveric study with simulated trochlear deformities.

PubMed

Van Haver, Annemieke; De Roo, Karel; De Beule, Matthieu; Labey, Luc; De Baets, Patrick; Dejour, David; Claessens, Tom; Verdonk, Peter

2015-06-01

Trochlear dysplasia appears in different geometrical variations. The Dejour classification is widely used to grade the severity of trochlear dysplasia and to decide on treatment. To investigate the effect of trochlear dysplasia on patellofemoral biomechanics and to determine if different types of trochlear dysplasia have different effects on patellofemoral biomechanics. Controlled laboratory study. Trochlear dysplasia was simulated in 4 cadaveric knees by replacing the native cadaveric trochlea with different types of custom-made trochlear implants, manufactured with 3-dimensional printing. For each knee, 5 trochlear implants were designed: 1 implant simulated the native trochlea (control condition), and 4 implants simulated 4 types of trochlear dysplasia. The knees were subjected to 3 biomechanical tests: a squat simulation, an open chain extension simulation, and a patellar stability test. The patellofemoral kinematics, contact area, contact pressure, and stability were compared between the control condition (replica implants) and the trochlear dysplastic condition and among the subgroups of trochlear dysplasia. The patellofemoral joint in the trochlear dysplastic group showed increased internal rotation, lateral tilt, and lateral translation; increased contact pressures; decreased contact areas; and decreased stability when compared with the control group. Within the trochlear dysplastic group, the implants graded as Dejour type D showed the largest deviations for the kinematical parameters, and the implants graded as Dejour types B and D showed the largest deviations for the patellofemoral contact areas and pressures. Patellofemoral kinematics, contact area, contact pressure, and stability are significantly affected by trochlear dysplasia. Of all types of trochlear dysplasia, the models characterized with a pronounced trochlear bump showed the largest deviations in patellofemoral biomechanics. Investigating the relationship between the shape of the trochlea and patellofemoral biomechanics can provide insight into the short-term effects (maltracking, increased pressures, and instability) and long-term effects (osteoarthritis) of different types of trochlear dysplasia. Furthermore, this investigation provides an empirical explanation for better treatment outcomes of trochleoplasty for Dejour types B and D dysplasia. © 2015 The Author(s).

Statistical radii associated with amino acids to determine the contact map: fixing the structure of a type I cohesin domain in the Clostridium thermocellum cellulosome

NASA Astrophysics Data System (ADS)

Chwastyk, Mateusz; Poma Bernaola, Adolfo; Cieplak, Marek

2015-07-01

We propose to improve and simplify protein refinement procedures through consideration of which pairs of amino acid residues should form native contacts. We first consider 11 330 proteins from the CATH database to determine statistical distributions of contacts associated with a given type of amino acid. The distributions are set across the distances between the α-C atoms that are in contact. Based on this data, we determine typical radii of effective spheres that can be placed on the α-C atoms in order to reconstruct the distribution of the contact lengths. This is done by checking for overlaps with enlarged van der Waals spheres associated with heavy atoms on other amino acids. The resulting contacts can be used to identify non-native contacts that may arise during the time evolution of structure-based models. Here, the radii are used to guide reconstruction of nine missing side chains in a type I cohesin domain with the Protein Data Bank code 1AOH. We first identify the likely missing contacts and then sculpt the corresponding side chains by standard refinement tools to achieve consistency with the expected contact map. One ambiguity in refinement is resolved by determining all-atom conformational energies.

Correlation between the electrical properties and the interfacial microstructures of TiAl-based ohmic contacts to p-type 4H-SiC

NASA Astrophysics Data System (ADS)

Tsukimoto, S.; Nitta, K.; Sakai, T.; Moriyama, M.; Murakami, Masanori

2004-05-01

In order to understand a mechanism of TiAl-based ohmic contact formation for p-type 4H-SiC, the electrical properties and microstructures of Ti/Al and Ni/Ti/Al contacts, which provided the specific contact resistances of approximately 2×10-5 Ω-cm2 and 7×10-5 Ω-cm2 after annealing at 1000°C and 800°C, respectively, were investigated using x-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). Ternary Ti3SiC2 carbide layers were observed to grow on the SiC surfaces in both the Ti/Al and the Ni/Ti/Al contacts when the contacts yielded low resistance. The Ti3SiC2 carbide layers with hexagonal structures had an epitaxial orientation relationship with the 4H-SiC substrates. The (0001)-oriented terraces were observed periodically at the interfaces between the carbide layers and the SiC, and the terraces were atomically flat. We believed the Ti3SiC2 carbide layers primarily reduced the high Schottky barrier height at the contact metal/p-SiC interface down to about 0.3 eV, and, thus, low contact resistances were obtained for p-type TiAl-based ohmic contacts.

Relationship between healthcare worker surface contacts, care type and hand hygiene: an observational study in a single-bed hospital ward.

PubMed

King, M-F; Noakes, C J; Sleigh, P A; Bale, S; Waters, L

2016-09-01

This study quantifies the relationship between hand hygiene and the frequency with which healthcare workers (HCWs) touch surfaces in patient rooms. Surface contacts and hand hygiene were recorded in a single-bed UK hospital ward for six care types. Surface contacts often formed non-random patterns, but hygiene before or after patient contact depends significantly on care type (P=0.001). The likelihood of hygiene correlated with the number of surface contacts (95% confidence interval 1.1-5.8, P=0.002), but not with time spent in the room. This highlights that a potential subconscious need for hand hygiene may have developed in HCWs, which may support and help focus future hygiene education programmes. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

RZ Leonis Minoris bridging between ER Ursae Majoris-type dwarf nova and nova-like system

NASA Astrophysics Data System (ADS)

Kato, Taichi; Ishioka, Ryoko; Isogai, Keisuke; Kimura, Mariko; Imada, Akira; Miller, Ian; Masumoto, Kazunari; Nishino, Hirochika; Kojiguchi, Naoto; Kawabata, Miho; Sakai, Daisuke; Sugiura, Yuki; Furukawa, Hisami; Yamamura, Kenta; Kobayashi, Hiroshi; Matsumoto, Katsura; Wang, Shiang-Yu; Chou, Yi; Ngeow, Chow-Choong; Chen, Wen-Ping; Panwar, Neelam; Lin, Chi-Sheng; Hsiao, Hsiang-Yao; Guo, Jhen-Kuei; Lin, Chien-Cheng; Omarov, Chingis; Kusakin, Anatoly; Krugov, Maxim; Starkey, Donn R.; Pavlenko, Elena P.; Antonyuk, Kirill A.; Sosnjvskij, Aleksei A.; Antonyuk, Oksana I.; Pit, Nikolai V.; Baklanov, Alex V.; Babina, Julia V.; Itoh, Hiroshi; Padovan, Stefano; Akazawa, Hidehiko; Kafka, Stella; de Miguel, Enrique; Pickard, Roger D.; Kiyota, Seiichiro; Shugarov, Sergey Yu.; Chochol, Drahomir; Krushevska, Viktoriia; Sekeráš, Matej; Pikalova, Olga; Sabo, Richard; Dubovsky, Pavol A.; Kudzej, Igor; Ulowetz, Joseph; Dvorak, Shawn; Stone, Geoff; Tordai, Tamás; Dubois, Franky; Logie, Ludwig; Rau, Steve; Vanaverbeke, Siegfried; Vanmunster, Tonny; Oksanen, Arto; Maeda, Yutaka; Kasai, Kiyoshi; Katysheva, Natalia; Morelle, Etienne; Neustroev, Vitaly V.; Sjoberg, George

2016-12-01

We observed RZ LMi, which is renowned for its extremely short (˜19 d) supercycle and is a member of a small, unusual class of cataclysmic variables called ER UMa-type dwarf novae, in 2013 and 2016. In 2016, the supercycles of this object substantially lengthened in comparison to the previous measurements to 35, 32, and 60 d for three consecutive superoutbursts. We consider that the object virtually experienced a transition to the nova-like state (permanent superhumper). This observed behavior reproduced the prediction of the thermal-tidal instability model extremely well. We detected a precursor in the 2016 superoutburst and detected growing (stage A) superhumps with a mean period of 0.0602(1) d in 2016 and in 2013. Combined with the period of superhumps immediately after the superoutburst, the mass ratio is not as small as in WZ Sge-type dwarf novae, having orbital periods similar to RZ LMi. By using least absolute shrinkage and selection operator (Lasso) two-dimensional power spectra, we detected possible negative superhumps with a period of 0.05710(1) d. We estimated an orbital period of 0.05792 d, which suggests a mass ratio of 0.105(5). This relatively large mass ratio is even above that of ordinary SU UMa-type dwarf novae, and it is also possible that the exceptionally high mass-transfer rate in RZ LMi may be a result of a stripped secondary with an evolved core in a system evolving toward an AM CVn-type object.

Contact variables for exposure to avian influenza H5N1 virus at the human-animal interface.

PubMed

Rabinowitz, P; Perdue, M; Mumford, E

2010-06-01

Although the highly pathogenic avian influenza H5N1 virus continues to cause infections in both avian and human populations, the specific zoonotic risk factors remain poorly understood. This review summarizes available evidence regarding types of contact associated with transmission of H5N1 virus at the human-animal interface. A systematic search of the published literature revealed five analytical studies and 15 case reports describing avian influenza transmission from animals to humans for further review. Risk factors identified in analytical studies were compared, and World Health Organization-confirmed cases, identified in case reports, were classified according to type of contact reported using a standardized algorithm. Although cases were primarily associated with direct contact with sick/unexpectedly dead birds, some cases reported only indirect contact with birds or contaminated environments or contact with apparently healthy birds. Specific types of contacts or activities leading to exposure could not be determined from data available in the publications reviewed. These results support previous reports that direct contact with sick birds is not the only means of human exposure to avian influenza H5N1 virus. To target public health measures and disease awareness messaging for reducing the risk of zoonotic infection with avian influenza H5N1 virus, the specific types of contacts and activities leading to transmission need to be further understood. The role of environmental virus persistence, shedding of virus by asymptomatic poultry and disease pathophysiology in different avian species relative to human zoonotic risk, as well as specific modes of zoonotic transmission, should be determined.

Engineering few-layer MoTe2 devices by Co/hBN tunnel contacts

NASA Astrophysics Data System (ADS)

Zhu, Mengjian; Luo, Wei; Wu, Nannan; Zhang, Xue-ao; Qin, Shiqiao

2018-04-01

2H phase Molybdenum ditelluride (MoTe2) is a layered two-dimensional (2D) semiconductor that has recently gained extensive attention for its intriguing properties, demonstrating great potential for nanoelectronics and optoelectronics. Optimizing the electric contacts to MoTe2 is a critical step for realizing high performance devices. Here, we demonstrate Co/hBN tunnel contacts to few-layer MoTe2. In sharp contrast to the p-type conduction of Co contacted MoTe2, Co/hBN tunnel contacted MoTe2 devices show clear n-type transport properties. Our first principles calculation reveals that the inserted few-layer hBN strongly interacts with Co and significantly reduces its work-function by ˜1.2 eV, while MoTe2 itself has a much weaker influence on the work-function of Co. This allows us to build MoTe2 diodes using the mixed Co/hBN and Co contact architecture, which can be switched from p-n type to n-p type by changing the gate-voltage, paving the way for engineering multi-functional devices based on atomically thin 2D semiconductors.

Tuning the electronic properties and Schottky barrier height of the vertical graphene/MoS2 heterostructure by an electric gating

NASA Astrophysics Data System (ADS)

Nguyen, Chuong V.

2018-04-01

In this paper, the electronic properties and Schottky contact in graphene/MoS2 (G/MoS2) heterostructure under an applied electric field are investigated by means of the density functional theory. It can be seen that the electronic properties of the G/MoS2 heterostructure are preserved upon contacting owing to the weak van der Waals interaction. We found that the n-type Schottky contact is formed in the G/MoS2 heterostructure with the Schottky barrier height of 0.49 eV. Furthermore, both Schottky contact and Schottky barrier height in the G/MoS2 heterostructure could be controlled by the applied electric field. If a positive electric field of 4 V/nm is applied to the system, a transformation from the n-type Schottky contact to the p-type one was observed, whereas the system keeps an n-type Schottky contact when a negative electric field is applied. Our results may provide helpful information to design, fabricate, and understand the physics mechanism in the graphene-based two-dimensional van der Waals heterostructures like as G/MoS2 heterostructure.

Highly reflective Ag-Cu alloy-based ohmic contact on p-type GaN using Ru overlayer.

PubMed

Son, Jun Ho; Jung, Gwan Ho; Lee, Jong-Lam

2008-12-15

We report on a metallization scheme of high reflectance, low resistance, and smooth surface morphology ohmic contact on p-type GaN. Ag-Cu alloy/Ru contact showed low contact resistivity as low as 6.2 x 10(-6) Ohms cm(2) and high reflectance of 91% at 460 nm after annealing at 400 degrees C in air ambient. The oxidation annealing promoted the out-diffusion of Ga atoms to dissolve in an Ag-Cu layer with the formation of an Ag-Ga solid solution, lowering the contact resistivity. The Ru overlayer acts as a diffusion barrier for excessive oxygen incorporation during oxidation annealing, resulting in high reflectance, good thermal stability, and smooth surface quality of the contact.

Electrical Characteristics of 10-kV 4H-SiC MPS Rectifiers with High Schottky Barrier Height

NASA Astrophysics Data System (ADS)

Jiang, Yifan; Sung, Woongje; Baliga, Jayant; Wang, Sizhen; Lee, Bongmook; Huang, Alex

2018-02-01

This paper reports the study of the fabrication and characterization results of 10-kilo-volt (kV) 4H-SiC merged PiN/Schottky rectifiers. A metal contact process was developed to make the Schottky contact on n-type SiC and ohmic contact on p-type SiC at the same time. The diodes with different Schottky contact width were fabricated and characterized for comparison. With the improvement quality of the Schottky contact and the passivation layer, the devices show low leakage current up to 10 kV. The on-state characteristics from room temperature to elevated temperature (423 K) were demonstrated and compared between structures with different Schottky contact width.

Epitaxially grown collagen fibrils reveal diversity in contact guidance behavior among cancer cells.

PubMed

Wang, Juan; Petefish, Joseph W; Hillier, Andrew C; Schneider, Ian C

2015-01-01

Invasion of cancer cells into the surrounding tissue is an important step during cancer progression and is driven by cell migration. Cell migration can be random, but often it is directed by various cues such as aligned fibers composed of extracellular matrix (ECM), a process called contact guidance. During contact guidance, aligned fibers bias migration along the long axis of the fibers. These aligned fibers of ECM are commonly composed of type I collagen, an abundant structural protein around tumors. In this paper, we epitaxially grew several different patterns of organized type I collagen on mica and compared the morphology and contact guidance behavior of two invasive breast cancer cell lines (MDA-MB-231 and MTLn3 cells). Others have shown that these cells randomly migrate in qualitatively different ways. MDA-MB-231 cells exert large traction forces, tightly adhere to the ECM, and migrate with spindle-shaped morphology and thus adopt a mesenchymal mode of migration. MTLn3 cells exert small traction forces, loosely adhere to the ECM, and migrate with a more rounded morphology and thus adopt an amoeboid mode of migration. As the degree of alignment of type I collagen fibrils increases, cells become more elongated and engage in more directed contact guidance. MDA-MB-231 cells perceive the directional signal of highly aligned type I collagen fibrils with high fidelity, elongating to large extents and migrating directionally. Interestingly, behavior in MTLn3 cells differs. While highly aligned type I collagen fibril patterns facilitate spreading and random migration of MTLn3 cells, they do not support elongation or directed migration. Thus, different contact guidance cues bias cell migration differently and the fidelity of contact guidance is cell type dependent, suggesting that ECM alignment is a permissive cue for contact guidance, but requires a cell to have certain properties to interpret that cue.

Metal contact engineering and registration-free fabrication of complementary metal-oxide semiconductor integrated circuits using aligned carbon nanotubes.

PubMed

Wang, Chuan; Ryu, Koungmin; Badmaev, Alexander; Zhang, Jialu; Zhou, Chongwu

2011-02-22

Complementary metal-oxide semiconductor (CMOS) operation is very desirable for logic circuit applications as it offers rail-to-rail swing, larger noise margin, and small static power consumption. However, it remains to be a challenging task for nanotube-based devices. Here in this paper, we report our progress on metal contact engineering for n-type nanotube transistors and CMOS integrated circuits using aligned carbon nanotubes. By using Pd as source/drain contacts for p-type transistors, small work function metal Gd as source/drain contacts for n-type transistors, and evaporated SiO(2) as a passivation layer, we have achieved n-type transistor, PN diode, and integrated CMOS inverter with an air-stable operation. Compared with other nanotube n-doping techniques, such as potassium doping, PEI doping, hydrazine doping, etc., using low work function metal contacts for n-type nanotube devices is not only air stable but also integrated circuit fabrication compatible. Moreover, our aligned nanotube platform for CMOS integrated circuits shows significant advantage over the previously reported individual nanotube platforms with respect to scalability and reproducibility and suggests a practical and realistic approach for nanotube-based CMOS integrated circuit applications.

Can simultaneous contact allergies to phenyl glycidyl ether and epoxy resins of the bisphenol A/F-types be explained by contamination of the epoxy resins?

PubMed

Pontén, Ann; Zimerson, Erik; Bruze, Magnus

2008-11-01

Simultaneous contact allergies to epoxy resins based on diglycidyl ether of bisphenol A (DGEBA-R) or epoxy resins of the bisphenol F-type and the reactive diluent phenyl glycidyl ether (PGE) have been reported. The reason might be cross-reactivity, exposure to an epoxy resin system with PGE as a component, or contamination by PGE in the epoxy resin. To study contamination by PGE, 20 commercial epoxy resins were analysed for the presence of PGE. To study contact allergy to PGE and its relation to epoxy resins by inserting PGE in the standard series. Among 2227 patients, 7 reacted to PGE. Of 23 (30%) patients, 7 with contact allergy to DGEBA-R and 7/19 (37%) with contact allergy to an epoxy resin of the bisphenol F-type reacted to PGE. All 7 patients with contact allergy to PGE reacted both to the DGEBA-R and to the epoxy resin of the bisphenol F-type. PGE was found in 90% of the investigated resins. The amounts of PGE ranged between 0.004% w/w and 0.18% w/w. Most probably, the presence of PGE as a contaminant in epoxy resins is of minor importance for the sensitization, but possibly the contamination of PGE might elicit contact dermatitis in individuals with a high reactivity to PGE.

The Palomar Transient Factory Orion Project: Eclipsing Binaries and Young Stellar Objects

NASA Astrophysics Data System (ADS)

van Eyken, Julian C.; Ciardi, David R.; Rebull, Luisa M.; Stauffer, John R.; Akeson, Rachel L.; Beichman, Charles A.; Boden, Andrew F.; von Braun, Kaspar; Gelino, Dawn M.; Hoard, D. W.; Howell, Steve B.; Kane, Stephen R.; Plavchan, Peter; Ramírez, Solange V.; Bloom, Joshua S.; Cenko, S. Bradley; Kasliwal, Mansi M.; Kulkarni, Shrinivas R.; Law, Nicholas M.; Nugent, Peter E.; Ofek, Eran O.; Poznanski, Dovi; Quimby, Robert M.; Grillmair, Carl J.; Laher, Russ; Levitan, David; Mattingly, Sean; Surace, Jason A.

2011-08-01

The Palomar Transient Factory (PTF) Orion project is one of the experiments within the broader PTF survey, a systematic automated exploration of the sky for optical transients. Taking advantage of the wide (3fdg5 × 2fdg3) field of view available using the PTF camera installed at the Palomar 48 inch telescope, 40 nights were dedicated in 2009 December to 2010 January to perform continuous high-cadence differential photometry on a single field containing the young (7-10 Myr) 25 Ori association. Little is known empirically about the formation of planets at these young ages, and the primary motivation for the project is to search for planets around young stars in this region. The unique data set also provides for much ancillary science. In this first paper, we describe the survey and the data reduction pipeline, and present some initial results from an inspection of the most clearly varying stars relating to two of the ancillary science objectives: detection of eclipsing binaries and young stellar objects. We find 82 new eclipsing binary systems, 9 of which are good candidate 25 Ori or Orion OB1a association members. Of these, two are potential young W UMa type systems. We report on the possible low-mass (M-dwarf primary) eclipsing systems in the sample, which include six of the candidate young systems. Forty-five of the binary systems are close (mainly contact) systems, and one of these shows an orbital period among the shortest known for W UMa binaries, at 0.2156509 ± 0.0000071 days, with flat-bottomed primary eclipses, and a derived distance that appears consistent with membership in the general Orion association. One of the candidate young systems presents an unusual light curve, perhaps representing a semi-detached binary system with an inflated low-mass primary or a star with a warped disk, and may represent an additional young Orion member. Finally, we identify 14 probable new classical T-Tauri stars in our data, along with one previously known (CVSO 35) and one previously reported as a candidate weak-line T-Tauri star (SDSS J052700.12+010136.8).

Modeling of contact theories for the manipulation of biological micro/nanoparticles in the form of circular crowned rollers based on the atomic force microscope

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korayem, M. H.; Khaksar, H.; Taheri, M.

2013-11-14

This article has dealt with the development and modeling of various contact theories for biological nanoparticles shaped as cylinders and circular crowned rollers for application in the manipulation of different biological micro/nanoparticles based on Atomic Force Microscope. First, the effective contact forces were simulated, and their impact on contact mechanics simulation was investigated. In the next step, the Hertz contact model was simulated and compared for gold and DNA nanoparticles with the three types of spherical, cylindrical, and circular crowned roller type contact geometries. Then by reducing the length of the cylindrical section in the circular crowned roller geometry, themore » geometry of the body was made to approach that of a sphere, and the results were compared for DNA nanoparticles. To anticipatory validate the developed theories, the results of the cylindrical and the circular crowned roller contacts were compared with the results of the existing spherical contact simulations. Following the development of these contact models for the manipulation of various biological micro/nanoparticles, the cylindrical and the circular crowned roller type contact theories were modeled based on the theories of Lundberg, Dowson, Nikpur, Heoprich, and Hertz for the manipulation of biological micro/nanoparticles. Then, for a more accurate validation, the results obtained from the simulations were compared with those obtained by the finite element method and with the experimental results available in previous articles. The previous research works on the simulation of nanomanipulation have mainly investigated the contact theories used in the manipulation of spherical micro/nanoparticles. However since in real biomanipulation situations, biological micro/nanoparticles of more complex shapes need to be displaced in biological environments, this article therefore has modeled and compared, for the first time, different contact theories for use in the biomanipulation of cylindrical and circular crowned roller shaped micro/nanoparticles. The results of models indicate that the contact model of Hertz achieves the largest amount of deformation for the DNA nanoparticle in cylindrical form and the contact model of Heoprich achieves the largest deformation for the circular crowned roller shaped DNA. Of course, this finding is not always true for the other nanoparticles; and considering the mechanical and environmental characteristics, different results can be obtained. Also, by comparing the deformations of different types of nanoparticles, it was determined that the platelet type nanoparticles display the highest degree of deformation in all the considered models, due to their particular mechanical characteristics.« less

Taking advantage of local structure descriptors to analyze interresidue contacts in protein structures and protein complexes.

PubMed

Martin, Juliette; Regad, Leslie; Etchebest, Catherine; Camproux, Anne-Claude

2008-11-15

Interresidue protein contacts in proteins structures and at protein-protein interface are classically described by the amino acid types of interacting residues and the local structural context of the contact, if any, is described using secondary structures. In this study, we present an alternate analysis of interresidue contact using local structures defined by the structural alphabet introduced by Camproux et al. This structural alphabet allows to describe a 3D structure as a sequence of prototype fragments called structural letters, of 27 different types. Each residue can then be assigned to a particular local structure, even in loop regions. The analysis of interresidue contacts within protein structures defined using Voronoï tessellations reveals that pairwise contact specificity is greater in terms of structural letters than amino acids. Using a simple heuristic based on specificity score comparison, we find that 74% of the long-range contacts within protein structures are better described using structural letters than amino acid types. The investigation is extended to a set of protein-protein complexes, showing that the similar global rules apply as for intraprotein contacts, with 64% of the interprotein contacts best described by local structures. We then present an evaluation of pairing functions integrating structural letters to decoy scoring and show that some complexes could benefit from the use of structural letter-based pairing functions.

Pure silver ohmic contacts to N- and P- type gallium arsenide materials

DOEpatents

Hogan, Stephen J.

1986-01-01

Disclosed is an improved process for manufacturing gallium arsenide semiconductor devices having as its components an n-type gallium arsenide substrate layer and a p-type gallium arsenide diffused layer. The improved process comprises forming a pure silver ohmic contact to both the diffused layer and the substrate layer, wherein the n-type layer comprises a substantially low doping carrier concentration.

Improving the ohmic properties of contacts to P-GaN by adding p-type dopants into the metallization layer

NASA Astrophysics Data System (ADS)

Liday, Jozef; Vogrinčič, Peter; Vincze, Andrej; Breza, Juraj; Hotový, Ivan

2012-12-01

The work investigates an increase of the density of free charge carriers in the sub-surface region of p-GaN by adding p-type dopants into the Ni-O layer of an Au/Ni-O metallization structure. We have examined electrical properties and concentration depth profiles of contact structures Au/Ni-Mg-O/p-GaN and Au/Ni-Zn-O/p-GaN, thus with magnesium and zinc as p-type dopants. The metallization layers were deposited on p-GaN by DC reactive magnetron sputtering in an atmosphere with a low concentration of oxygen (0.2 at%). The contacts were annealed in N2 . We have found that the structures containing magnesium or zinc exhibit lower values of contact resistivity in comparison with otherwise identical contacts without Mg or Zn dopants. In our opinion, the lower values of contact resistivity of the structures containing of Mg or Zn are caused by an increased density of holes in the sub-surface region of p-GaN due to diffusion of Mg or Zn from the deposited doped contact layers.

Separation of distinct adhesion complexes and associated cytoskeleton by a micro-stencil-printing method.

PubMed

Caballero, David; Osmani, Naël; Georges-Labouesse, Elisabeth; Labouesse, Michel; Riveline, Daniel

2012-01-01

Adhesion between cells and the extracellular matrix is mediated by different types of transmembraneous proteins. Their associations to specific partners lead to the assembly of contacts such as focal adhesions and hemidesmosomes. The spatial overlap between both contacts within cells has however limited the study of each type of contact. Here we show that with "stampcils" focal contacts and hemidesmosomes can be spatially separated: cells are plated within the cavities of a stencil and the grids of the stencil serve as stamps for grafting an extracellular matrix protein-fibronectin. Cells engage new contacts on stamped zones leading to the segregation of adhesions and their associated cytoskeletons, i.e., actin and intermediate filaments of keratins. This new method should provide new insights into cell contacts compositions and dynamics.

[Measurement of external pressure of peroneal nerve tract coming in contact with lithotomy leg holders using pressure distribution measurement system BIG-MAT®].

PubMed

Mizuno, Ju; Namba, Chikara; Takahashi, Toru

2014-10-01

We investigated external pressure on peroneal nerve tract coming in contact with two kinds of leg holders using pressure distribution measurement system BIG- MAT® (Nitta Corp., Osaka) in the lithotomy position Peak contact (active) pressure at the left fibular head region coming in contact with knee-crutch-type leg holder M® (Takara Belmont Corp., Osaka), which supports the left popliteal fossa, was 78.0 ± 26.4 mmHg. On the other hand, peak contact pressure at the left lateral lower leg region coming in contact with boot-support-type leg holder Bel Flex® (Takara Belmont Corp., Osaka), which supports the left lower leg and foot was 26.3±7.9 mmHg. These results suggest that use of knee-crutch-type leg holder is more likely to induce common peroneal nerve palsy at the fibular head region, but use of boot-support-type leg holder dose not easily induce superficial peroneal nerve palsy at the lateral lower leg region, because capillary blood pressure is known to be 32 mmHg. Safer holders for positioning will be developed to prevent nerve palsy based on the analysis of chronological change in external pressure using BIG-MAT® system during anesthesia.

Tuning the Schottky contacts in the phosphorene and graphene heterostructure by applying strain.

PubMed

Liu, Biao; Wu, Li-Juan; Zhao, Yu-Qing; Wang, Lin-Zhi; Caii, Meng-Qiu

2016-07-20

The structures and electronic properties of the phosphorene and graphene heterostructure are investigated by density functional calculations using the hybrid Heyd-Scuseria-Ernzerhof (HSE) functional. The results show that the intrinsic properties of phosphorene and graphene are preserved due to the weak van der Waals contact. But the electronic properties of the Schottky contacts in the phosphorene and graphene heterostructure can be tuned from p-type to n-type by the in-plane compressive strains from -2% to -4%. After analyzing the total band structure and density of states of P atom orbitals, we find that the Schottky barrier height (SBH) is determined by the P-pz orbitals. What is more, the variation of the work function of the phosphorene monolayer and the graphene electrode and the Fermi level shift are the nature of the transition of Schottky barrier from n-type Schottky contact to p-type Schottky contact in the phosphorene and graphene heterostructure under different in-plane strains. We speculate that these are general results of tuning of the electronic properties of the Schottky contacts in the phosphorene and graphene heterostructure by controlling the in-plane compressive strains to obtain a promising method to design and fabricate a phosphorene-graphene based field effect transistor.

Contact-Allergic Reactions to Cosmetics

PubMed Central

Goossens, An

2011-01-01

Contact-allergic reactions to cosmetics may be delayed-type reactions such as allergic and photo-allergic contact dermatitis, and more exceptionally also immediate-type reactions, that is, contact urticaria. Fragrances and preservative agents are the most important contact allergens, but reactions also occur to category-specific products such as hair dyes and other hair-care products, nail cosmetics, sunscreens, as well as to antioxidants, vehicles, emulsifiers, and, in fact, any possible cosmetic ingredient. Patch and prick testing to detect the respective culprits remains the golden standard for diagnosis, although additional tests might be useful as well. Once the specific allergens are identified, the patients should be informed of which products can be safely used in the future. PMID:21461388

Electronic Properties of Graphene-PtSe2 Contacts.

PubMed

Sattar, Shahid; Schwingenschlögl, Udo

2017-05-10

In this article, we study the electronic properties of graphene in contact with monolayer and bilayer PtSe 2 using first-principles calculations. It turns out that there is no charge transfer between the components because of the weak van der Waals interaction. We calculate the work functions of monolayer and bilayer PtSe 2 and analyze the band bending at the contact with graphene. The formation of an n-type Schottky contact with monolayer PtSe 2 and a p-type Schottky contact with bilayer PtSe 2 is demonstrated. The Schottky barrier height is very low in the bilayer case and can be reduced to zero by 0.8% biaxial tensile strain.

Method and apparatus for improving heat transfer in a fluidized bed

DOEpatents

Lessor, Delbert L.; Robertus, Robert J.

1990-01-01

An apparatus contains a fluidized bed that includes particles of different triboelectrical types, each particle type acquiring an opposite polarity upon contact. The contact may occur between particles of the two types or between particles of etiher type and structure or fluid present in the apparatus. A fluidizing gas flow is passed through the particles to produce the fluidized bed. Immersed within the bed are electrodes. An alternating EMF source connected to the electrodes applies an alternating electric field across the fluidized bed to cause particles of the first type to move relative to particles of the second type and relative to the gas flow. In a heat exchanger incorporating the apparatus, the electrodes are conduits conveying a fluid to be heated. The two particle types alternately contact each conduit to transfer heat from a hot gas flow to the second fluid within the conduit.

The steady-state tangential contact problem for a falling drop type of contact area on corrugated rail by simplified theory of rolling contact

NASA Astrophysics Data System (ADS)

Piotrowski, Jerzy

1991-10-01

Investigation of contact mechanical nonlinearities of a mathematical model of corrugation revealed that the typical shape of contact patch resembles a falling drop of water. A contact patch of that shape was approximated with a figure composed of two parts of ellipses with different eccentricities. The contact pressure distribution was assumed as a smoothing ensemble of two paraboloidal distributions. The description of a general case of double half elliptical contact area was given but a special case of double half elliptical contact is more interesting as it possesses some Hertzian properties. It was shown how three geometrical parameters of double half elliptical contact can be chosen when actual, non-Hertzian contact is known. A linear theory was written which indicates that the lateral vibrations of the rail may be excited only due to shape variation on corrugation even if any other cause for these vibrations does not exist. For nonlinear theory a computer program, based on FASTSIM algorithm by Kalker, was written. The aim is to calculate the creep forces and frictional power density distribution over the contact area. Also, a graphic program visualizing the solution was written. Numerical results are not provided; unattended and unsolved problems relevant for this type of contact are listed.

Self-aligned Ni-P ohmic contact scheme for silicon solar cells by electroless deposition

NASA Astrophysics Data System (ADS)

Lee, Eun Kyung; Lim, Dong Chan; Lee, Kyu Hwan; Lim, Jae-Hong

2012-08-01

We report a Ni-P metallization scheme for low resistance ohmic contacts to n-type Si for silicon solar cells. As-deposited Ni-P contacts to n-type Si showed a specific contact resistance of 6.42 × 10-4 Ω·cm2. The specific contact resistance decreased with increasing thermal annealing temperature. When the Ni-P contact was annealed at 600°C for 30 min in ambient air, the specific contact resistance was greatly decreased, to 6.37 × 10-5Ω·cm2. The improved ohmic property was attributed to the decrease in the work function due to the formation of Ni-silicides from Ni in-diffusion during the thermal annealing process. Effects of the annealing process on the electrical and crystal properties of the contacts were investigated by means of various resistivity measurements (circular transmission line method (c-TLM), 4-point probe), glancing angle x-ray diffraction (GAXRD), and x-ray photoelectron spectroscopy (XPS).

On summary measure analysis of linear trend repeated measures data: performance comparison with two competing methods.

PubMed

Vossoughi, Mehrdad; Ayatollahi, S M T; Towhidi, Mina; Ketabchi, Farzaneh

2012-03-22

The summary measure approach (SMA) is sometimes the only applicable tool for the analysis of repeated measurements in medical research, especially when the number of measurements is relatively large. This study aimed to describe techniques based on summary measures for the analysis of linear trend repeated measures data and then to compare performances of SMA, linear mixed model (LMM), and unstructured multivariate approach (UMA). Practical guidelines based on the least squares regression slope and mean of response over time for each subject were provided to test time, group, and interaction effects. Through Monte Carlo simulation studies, the efficacy of SMA vs. LMM and traditional UMA, under different types of covariance structures, was illustrated. All the methods were also employed to analyze two real data examples. Based on the simulation and example results, it was found that the SMA completely dominated the traditional UMA and performed convincingly close to the best-fitting LMM in testing all the effects. However, the LMM was not often robust and led to non-sensible results when the covariance structure for errors was misspecified. The results emphasized discarding the UMA which often yielded extremely conservative inferences as to such data. It was shown that summary measure is a simple, safe and powerful approach in which the loss of efficiency compared to the best-fitting LMM was generally negligible. The SMA is recommended as the first choice to reliably analyze the linear trend data with a moderate to large number of measurements and/or small to moderate sample sizes.

Process for forming pure silver ohmic contacts to N- and P-type gallium arsenide materials

DOEpatents

Hogan, S.J.

1983-03-13

Disclosed is an improved process for manufacturing gallium arsenide semiconductor devices having as its components a n-type gallium arsenide substrate layer and a p-type gallium arsenide diffused layer. The improved process comprises forming a pure silver ohmic contact to both the diffuse layer and the substrate layer wherein the n-type layer comprises a substantially low doping carrier concentration.

75 FR 63502 - Sonny Bono Salton Sea National Wildlife Refuge Complex (Sonny Bono Salton Sea National Wildlife...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-15

...- toed lizard (Uma inornata), as well as other desert-dwelling species adapted to living in the sand dune...., conversion of habitat types, dust management, degraded water quality); predation in seabird nesting areas... sand on adjacent properties; public use; and impacts to Refuge resources as a result of illegal...

A Long Term Study of the Water Content Changes in Three Types of Hydrogel Contact Lenses.

DTIC Science & Technology

1987-05-01

7RD-R1BS 579 A LONG TERM STUDY OF THE HATER CONTENT CHANGES IN THREE 1/2 TYPES OF HYDROGEL ..(U) AIR FORCE INST OF TECH URIGHT-PATTERSON AFI OH L 0...The Water Content Changes THESIS/Dl$$XF$T$77q Ln ~In Three Types Of Hydrogel Contact Lenses G EFRIGI EOTNME IO 7. AUTHOR(.) S. CONTRACT OR GRANT NUMBER...SECURITY CLASSIFICATION OF THIS PAGE ("o~tn Date Entered) ABSTRACT A" Sufficient oxygen is required to pass through a hydrogel contact lens for proper

Back wall solar cell

NASA Technical Reports Server (NTRS)

Brandhorst, H. W., Jr. (Inventor)

1978-01-01

A solar cell is disclosed which comprises a first semiconductor material of one conductivity type with one face having the same conductivity type but more heavily doped to form a field region arranged to receive the radiant energy to be converted to electrical energy, and a layer of a second semiconductor material, preferably highly doped, of opposite conductivity type on the first semiconductor material adjacent the first semiconductor material at an interface remote from the heavily doped field region. Instead of the opposite conductivity layer, a metallic Schottky diode layer may be used, in which case no additional back contact is needed. A contact such as a gridded contact, previous to the radiant energy may be applied to the heavily doped field region of the more heavily doped, same conductivity material for its contact.

Drug prescriptions in Danish out-of-hours primary care: a 1-yearpopulation-based study

PubMed Central

Christensen, Morten Bondo; Nørøxe, Karen Busk; Moth, Grete; Vedsted, Peter; Huibers, Linda

2016-01-01

Objective General practitioners are the first point of contact in Danish out-of-hours (OOH) primary care. The large number of contacts implies that prescribing behaviour may have considerable impact on health-care expenditures and quality of care. The aim of this study was to examine the prevailing practices for medication prescription in Danish OOH with a particular focus on patient characteristics and contact type. Design and setting A one-year population-based retrospective observational study was performed of all contacts to OOH primary care in the Central Denmark Region using registry data. Main outcome measures Prescriptions were categorised according to Anatomical Therapeutic Chemical Classification (ATC) codes and stratified for patient age, gender and contact type (telephone consultation, clinic consultation or home visit). Prescription rates were calculated as number of prescriptions per 100 contacts. Results Of 644,777 contacts, 154,668 (24.0%) involved medication prescriptions; 21.9% of telephone consultations, 32.9% of clinic consultations and 14.3% of home visits. Around 53% of all drug prescriptions were made in telephone consultations. Anti-infective medications for systemic use accounted for 45.5% of all prescriptions and were the most frequently prescribed drug group for all contact types, although accounting for less than 1/3 of telephone prescriptions. Other frequently prescribed drugs were ophthalmological anti-infectives (10.5%), NSAIDs (6.4%), opioids (3.9%), adrenergic inhalants (3.0%) and antihistamines (2.3%). Conclusion About 25% of all OOH contacts involved one or more medication prescriptions. The highest prescription rate was found for clinic consultations, but more than half of all prescriptions were made by telephone. KEY POINTSAs the out-of-hours (OOH) primary care services cover more than 75% of all hours during a normal week, insight into the extent and type of OOH drug prescription is important.General practitioners (GPs) are responsible for more than 80% of all drug prescriptions in Denmark.Of all contacts 24.0% involved medication prescriptions; 21.9% of telephone consultations, 32.9% of clinic consultations and 14.3% of home visits.Of all prescriptions, 53% were made in telephone consultations.Anti-infective medications for systemic use accounted for 45.5% of all prescriptions, thereby being the most frequently prescribed drug group for all three contact types. PMID:27804314

Drug prescriptions in Danish out-of-hours primary care: a 1-yearpopulation-based study.

PubMed

Christensen, Morten Bondo; Nørøxe, Karen Busk; Moth, Grete; Vedsted, Peter; Huibers, Linda

2016-12-01

General practitioners are the first point of contact in Danish out-of-hours (OOH) primary care. The large number of contacts implies that prescribing behaviour may have considerable impact on health-care expenditures and quality of care. The aim of this study was to examine the prevailing practices for medication prescription in Danish OOH with a particular focus on patient characteristics and contact type. A one-year population-based retrospective observational study was performed of all contacts to OOH primary care in the Central Denmark Region using registry data. Prescriptions were categorised according to Anatomical Therapeutic Chemical Classification (ATC) codes and stratified for patient age, gender and contact type (telephone consultation, clinic consultation or home visit). Prescription rates were calculated as number of prescriptions per 100 contacts. Of 644,777 contacts, 154,668 (24.0%) involved medication prescriptions; 21.9% of telephone consultations, 32.9% of clinic consultations and 14.3% of home visits. Around 53% of all drug prescriptions were made in telephone consultations. Anti-infective medications for systemic use accounted for 45.5% of all prescriptions and were the most frequently prescribed drug group for all contact types, although accounting for less than 1/3 of telephone prescriptions. Other frequently prescribed drugs were ophthalmological anti-infectives (10.5%), NSAIDs (6.4%), opioids (3.9%), adrenergic inhalants (3.0%) and antihistamines (2.3%). About 25% of all OOH contacts involved one or more medication prescriptions. The highest prescription rate was found for clinic consultations, but more than half of all prescriptions were made by telephone. KEY POINTS As the out-of-hours (OOH) primary care services cover more than 75% of all hours during a normal week, insight into the extent and type of OOH drug prescription is important. General practitioners (GPs) are responsible for more than 80% of all drug prescriptions in Denmark. Of all contacts 24.0% involved medication prescriptions; 21.9% of telephone consultations, 32.9% of clinic consultations and 14.3% of home visits. Of all prescriptions, 53% were made in telephone consultations. Anti-infective medications for systemic use accounted for 45.5% of all prescriptions, thereby being the most frequently prescribed drug group for all three contact types.

Effect of Exposure Type and Timing of Injuries in Division I College Football: A 4-year Single Program Analysis.

PubMed

Krill, Michael K; Borchers, James R; Hoffman, Joshua T; Tatarski, Rachel L; Hewett, Timothy E

2017-02-01

Football players compete with a high risk of injury due to the sport. With the recent efforts to improve safety, the National Collegiate Athletic Association (NCAA) established new terminology to clearly define exposure types and reduce the number of high contact exposures. To compare football injury rates (IR) with a focus on game versus practice, time in season of injury, mechanism of injury and utilizing recent exposure types defined by the NCAA (live contact, full-pads and non-contact). Licensed medical professionals monitored a college football program regular season from 2012-2015. Each injury was classified by timing of the injury, mechanism of injury, and whether it occurred in game or practice. Player attendance and type of exposure (non-contact, full-pad or live contact, which involves live tackling to the ground and/or full-speed blocking and can occur in full-pad or half-pad ('shell') equipment) was documented. IR were calculated per 1000 athlete-exposures (AE). Mid-exact P tests compared rates between variables. The game IR was over three times as high as the practice IR (p < .001). Live contact exposures had the greatest IR of 5.702/1000 AE and were seven times more likely to produce an injury compared to non-contact exposures (p < .001); whereas, live contact exposures were about two times more likely to produce an injury compared to full-pad exposures (p = .004). The majority of injuries observed occurred from a contact mechanism (IR: 2.508/1000 AE). The highest IR during the fall football season occurred in the pre-season at 5.769/1000 AE. Overall IR observed in this cohort were lower than prior studies published before recent NCAA rule changes and guideline implementation to improve athlete safety. Athletes in this cohort were at significantly increased risk of injury from live contact exposures.

Mouthpiece ventilation in Duchenne muscular dystrophy: a rescue strategy for noncompliant patients.

PubMed

Fiorentino, Giuseppe; Annunziata, Anna; Cauteruccio, Rosa; Frega, Gianfranco Scotto di; Esquinas, Antonio

2016-01-01

To evaluate mouthpiece ventilation (MPV) in patients with Duchenne muscular dystrophy (DMD) who are noncompliant with noninvasive ventilation (NIV). We evaluated four young patients with DMD who had previously refused to undergo NIV. Each patient was reassessed and encouraged to try MPV. The four patients tolerated MPV well and were compliant with NIV at home. MPV proved to be preferable and more comfortable than NIV with any other type of interface. Two of the patients required overnight NIV and eventually agreed to use a nasal mask during the night. The advantages of MPV over other types of NIV include fewer speech problems, better appearance, and less impact on the patient, eliminating the risk of skin breakdown, gastric distension, conjunctivitis, and claustrophobia. The use of a mouthpiece interface should be always considered in patients with DMD who need to start NIV, in order to promote a positive approach and a rapid acceptance of NIV. Using MPV during the daytime makes patients feel safe and more likely to use NIV at night. In addition, MPV increases treatment compliance for those who refuse to use other types of interfaces. Avaliar a ventilação bucal (VB) em pacientes com distrofia muscular de Duchenne (DMD) não aderentes à ventilação não invasiva (VNI). Foram avaliados quatro pacientes jovens com DMD que anteriormente recusaram-se a se submeter à VNI. Cada paciente foi reavaliado e encorajado a tentar VB. Os quatro pacientes toleraram bem a VB e aderiram ao uso de VNI em casa. O uso de VB provou ser uma alternativa preferível e mais confortável que o uso de VNI com qualquer outro tipo de interface. Dois dos pacientes necessitaram de VNI noturna e eventualmente aceitaram utilizar uma máscara nasal durante a noite. As vantagens da VB sobre outros tipos de VNI incluem menores problemas na fala, melhor aparência e menor impacto no paciente, eliminando o risco de lesões na pele, distensão gástrica, conjuntivite e claustrofobia. O uso da interface bucal sempre deve ser considerado em pacientes com DMD que necessitam iniciar VNI a fim de promover uma abordagem positiva e uma rápida aceitação da VNI. O uso diurno de VB faz com que os pacientes sintam-se seguros e mais propensos a utilizar VNI à noite. Além disso, a VB aumenta a adesão ao tratamento naqueles pacientes que se recusam a utilizar outros tipos de interfaces.

Contact Lenses in the Laboratory.

ERIC Educational Resources Information Center

Kingston, David W.

1981-01-01

Summarizes results of a three-item questionnaire returned by 43 Michigan institutions expressing views on wearing contact lenses in chemical laboratories. Questions focused on eye protection, type of protection, and use of contact lenses. (SK)

Artificial muscles with adjustable stiffness

NASA Astrophysics Data System (ADS)

Mutlu, Rahim; Alici, Gursel

2010-04-01

This paper reports on a stiffness enhancement methodology based on using a suitably designed contact surface with which cantilevered-type conducting polymer bending actuators are in contact during operation. The contact surface constrains the bending behaviour of the actuators. Depending on the topology of the contact surface, the resistance of the polymer actuators to deformation, i.e. stiffness, is varied. As opposed to their predecessors, these polymer actuators operate in air. Finite element analysis and modelling are used to quantify the effect of the contact surface on the effective stiffness of a trilayer cantilevered beam, which represents a one-end-free, the-other-end-fixed polypyrrole (PPy) conducting polymer actuator under a uniformly distributed load. After demonstrating the feasibility of the adjustable stiffness concept, experiments were conducted to determine the stiffness of bending-type conducting polymer actuators in contact with a range (20-40 mm in radius) of circular contact surfaces. The numerical and experimental results presented demonstrate that the stiffness of the actuators can be varied using a suitably profiled contact surface. The larger the radius of the contact surface is, the higher is the stiffness of the polymer actuators. The outcomes of this study suggest that, although the stiffness of the artificial muscles considered in this study is constant for a given geometric size, and electrical and chemical operation conditions, it can be changed in a nonlinear fashion to suit the stiffness requirement of a considered application. The stiffness enhancement methodology can be extended to other ionic-type conducting polymer actuators.

[Comparative analysis of visual function and the quality of life index with eyeglasses or a progressive contact lens].

PubMed

Sant'Anna, Neusa Vidal; Schor, Paulo; Lipener, César; Uras, Ricardo

2006-01-01

To compare the visual function and the answers to a questionnaire of quality of life of patients wearing a progressive contact lens or eyeglasses. The Focus Progressive contact lens had been fitted in 35 patients with far visual acuity with progressive-addition eyeglasses equal to zero (log MAR) and near J1 (Jaeger). The far and near visual acuities and the measurement of contrast sensitivity were compared when the patients were wearing the eyeglasses or the contact lens and the patients' results of the scores of the quality of life questionnaire (NEI VFQ-25) were analyzed statistically considering the type of ametropy and the age. The far and near visual acuities and the contrast sensitivity measurement were worse with the contact lens than with eyeglasses. The answers to the questionnaire did not differ when were comparing the same patients wearing eyeglasses or contact lens, no matter the type of ametropy. The myopic and the hyperopic subgroups had worse answers to the quality of life questionnaire when corrected with the contact lens than with eyeglasses, both with age equal to or less than their median. The visual function was worse with the contact lens. The type of ametropy did not influence the answers to the quality of life questionnaire considering the optical correction, but age did.

Bacterial adhesion to conventional hydrogel and new silicone-hydrogel contact lens materials.

PubMed

Kodjikian, Laurent; Casoli-Bergeron, Emmanuelle; Malet, Florence; Janin-Manificat, Hélène; Freney, Jean; Burillon, Carole; Colin, Joseph; Steghens, Jean-Paul

2008-02-01

As bacterial adhesion to contact lenses may contribute to the pathogenesis of keratitis, the aim of our study was to investigate in vitro adhesion of clinically relevant bacteria to conventional hydrogel (standard HEMA) and silicone-hydrogel contact lenses using a bioluminescent ATP assay. Four types of unworn contact lenses (Etafilcon A, Galyfilcon A, Balafilcon A, Lotrafilcon B) were incubated with Staphylococcus epidermidis (two different strains) and Pseudomonas aeruginosa suspended in phosphate buffered saline (PBS). Lenses were placed with the posterior surface facing up and were incubated in the bacterial suspension for 4 hours at 37 degrees C. Bacterial binding was then measured and studied by bioluminescent ATP assay. Six replicate experiments were performed for each lens and strain. Adhesion of all species of bacteria to standard HEMA contact lenses (Etafilcon A) was found to be significantly lower than that of three types of silicone-hydrogel contact lenses, whereas Lotrafilcon B material showed the highest level of bacterial binding. Differences between species in the overall level of adhesion to the different types of contact lenses were observed. Adhesion of P. aeruginosa was typically at least 20 times greater than that observed with both S. epidermidis strains. Conventional hydrogel contact lenses exhibit significantly lower bacterial adhesion in vitro than silicone-hydrogel ones. This could be due to the greater hydrophobicity but also to the higher oxygen transmissibility of silicone-hydrogel lenses.

Fe-Si particles on the surface of blast furnace coke

NASA Astrophysics Data System (ADS)

Gornostayev, Stanislav S.; Heikkinen, Eetu-Pekka; Heino, Jyrki J.; Fabritius, Timo M. J.

2015-07-01

This study investigates the surface of unpolished samples of blast furnace (BF) coke drilled from the tuyere zone, which hosts Fe-Si particles (mostly Fe3Si) that vary in size, shape, depth of submersion (penetration) into the coke matrix, and contact features with the surface. Based on the shape of the particles and the extent of their contact with the coke matrix, they have been grouped into three major types: (I) sphere-like droplets with limited contact area, (II) semi-spheres with a larger contact area, and (III) irregular segregations with a spherical surface, which exhibit the largest contact area among the three types of particles. Considering the ratio between the height ( h) of the particles and half of their length at the surface level ( l) along the cross-section, these three types can be characterized as follows: (I) h > l, (II) h ≈ l, and (III) h < l. All the three types of particles can be found near each other. The shape and the extent of the contact depend on the degree of penetration of the material into the matrix, which is a function of the composition of the particles. Type (I) particles were initially saturated with Si at an earlier stage and, for that reason, they can react less with carbon in the coke matrix than type (II) and (III), thereby moving faster through the coke cone. Thermodynamic calculations have shown that the temperature interval of 1250-1300°C can be considered the starting point for Si entering into molten iron under quartz-dominated coke ash. Accordingly, the initial pick-up of Si by molten iron can be assumed to be mineral-related. In terms of BF practice, better conditions for sliding Fe-Si droplets through the coke cone are available when they come into contact with free SiO2 concentrated into small grains, and when the SiO2/ΣMe x O y mass ratio in the coke ash is high.

In situ ohmic contact formation for n-type Ge via non-equilibrium processing

NASA Astrophysics Data System (ADS)

Prucnal, S.; Frigerio, J.; Napolitani, E.; Ballabio, A.; Berencén, Y.; Rebohle, L.; Wang, M.; Böttger, R.; Voelskow, M.; Isella, G.; Hübner, R.; Helm, M.; Zhou, S.; Skorupa, W.

2017-11-01

Highly scaled nanoelectronics requires effective channel doping above 5 × 1019 cm-3 together with ohmic contacts with extremely low specific contact resistivity. Nowadays, Ge becomes very attractive for modern optoelectronics due to the high carrier mobility and the quasi-direct bandgap, but n-type Ge doped above 5 × 1019 cm-3 is metastable and thus difficult to be achieved. In this letter, we report on the formation of low-resistivity ohmic contacts in highly n-type doped Ge via non-equilibrium thermal processing consisting of millisecond-range flash lamp annealing. This is a single-step process that allows for the formation of a 90 nm thick NiGe layer with a very sharp interface between NiGe and Ge. The measured carrier concentration in Ge is above 9 × 1019 cm-3 with a specific contact resistivity of 1.2 × 10-6 Ω cm2. Simultaneously, both the diffusion and the electrical deactivation of P are fully suppressed.

Protein contact dermatitis: allergens, pathogenesis, and management.

PubMed

Levin, Cheryl; Warshaw, Erin

2008-01-01

Protein contact dermatitis is an allergic skin reaction induced principally by proteins of either animal or plant origin. The clinical presentation is that of a chronic dermatitis, and it is often difficult to differentiate between allergic contact dermatitis and other eczematous dermatoses. One distinguishing clinical feature is that acute flares of pruritus, urticaria, edema, or vesiculation are noted minutes after contact with the causative substances. Additionally, the patch-test result is typically negative, and the scratch- or prick-test result is positive. The pathogenesis of protein contact dermatitis is unclear but may involve a type I (immunoglobulin E [IgE], immediate) hypersensitivity reaction, type IV (cell-mediated delayed) hypersensitivity reaction, and/or a delayed reaction due to IgE-bearing Langerhans' cells. Management involves avoidance of the allergen.

Front contact solar cell with formed emitter

DOEpatents

Cousins, Peter John

2014-11-04

A bipolar solar cell includes a backside junction formed by an N-type silicon substrate and a P-type polysilicon emitter formed on the backside of the solar cell. An antireflection layer may be formed on a textured front surface of the silicon substrate. A negative polarity metal contact on the front side of the solar cell makes an electrical connection to the substrate, while a positive polarity metal contact on the backside of the solar cell makes an electrical connection to the polysilicon emitter. An external electrical circuit may be connected to the negative and positive metal contacts to be powered by the solar cell. The positive polarity metal contact may form an infrared reflecting layer with an underlying dielectric layer for increased solar radiation collection.

Front contact solar cell with formed emitter

DOEpatents

Cousins, Peter John [Menlo Park, CA

2012-07-17

A bipolar solar cell includes a backside junction formed by an N-type silicon substrate and a P-type polysilicon emitter formed on the backside of the solar cell. An antireflection layer may be formed on a textured front surface of the silicon substrate. A negative polarity metal contact on the front side of the solar cell makes an electrical connection to the substrate, while a positive polarity metal contact on the backside of the solar cell makes an electrical connection to the polysilicon emitter. An external electrical circuit may be connected to the negative and positive metal contacts to be powered by the solar cell. The positive polarity metal contact may form an infrared reflecting layer with an underlying dielectric layer for increased solar radiation collection.

The Oakland Conglomerate: a Hayward Fault Teconite?

NASA Astrophysics Data System (ADS)

Strayer, L. M.; Allen, J. R.

2008-12-01

The Late Cretaceous Oakland Conglomerate (OC), a coarse-grained cobble and sandstone unit of the Great Valley Sequence is a tectonite. Faulted and shattered cobbles and well developed grain-on-grain contact features between clasts are ubiquitous and penetrative throughout conglomeratic lenses. The OC outcrops east of the Hayward fault (HF) and adjacent to the Chabot fault in the East Bay Hills. It overlies the Knoxville Formation and may have been buried beneath 4-6 km of younger units. The OC is a proximal submarine fan deposit with sediment sourced to the ancestral Klamath and Sierra Nevada. Clast types are dominated by volcanics, granitoids, as well as numerous quartzites, perhaps reflecting complex provenance:Klamath and pre-Sierran arc and pre-Cretaceous Basin and Range. And although there was a significant interval between the Late-K deposition of the OC and the inception of San Andreas faulting in the Bay Area, its 1-2 km proximity to the HF in the Oakland Metropolitan area strongly suggests that much of the brittle-plastic deformation within the OC may be due to earthquakes upon the nearby Hayward fault. Clasts with the OC are frequently shattered, fractured or faulted. Most have grain-on-grain contact features on their surfaces regardless of whether they are matrix or grain supported. Faulting in the cobbles ranges from outcrop scale, penetrative and often conjugate shear fracture sets that run through both cobbles and matrix (if present), to closely spaced en-echelon faults that clearly deform cobbles, and radially shattered specimens with nearly conical conjugate shear fractures that are clearly the result of point loading due to grain-on-grain contact. There are at least 3 types of contact structures, ranging from: 1) Type-H, bright circular halos with little or no surface dimpling, likely the result of intense microfracture at the contact; 2) Type-S, shattered, rounded 'firing-pin' structures that have pulverized, depressed contact that is the locus of radial and conjugate shear fractures that offset the surface of the clasts. Cross-cutting relationships suggest that pulverized dimpling and faulting are synchronous. These appear to form both with and without matrix involvement. 3) Type-P, clean, well formed, pressure solution pits, often rimmed by a discrete lip of adjacent matrix, likely cemented by locally available quartz. These are often cut by the faults of Type-S above. Type-S and Type-P contact features can and often do occur in the same specimen. Type-H and some Type-S contacts appear to be products of 'clean' grain-on-grain contact without matrix involvement. Differences between the bright halo and the pressure solution pits may be due to the presence of a thin layer of matrix sand, which appears to facilitate wholesale pressure solution. Faults within the matrix and cobbles are often conjugate, and penetrative at the outcrop scale. Initial structural analysis suggests these faults might lend themselves to stress inversion techniques if enough examples are available. Since many of the cobbles were re-cemented after they were faulted, there may be potential to gain insight into their burial depths during these events by investigating their geochemistry. The OC, given its very close proximity to the HF, may provide a record of the shortening direction and stress orientations directly adjacent to this important plate boundary.

Adoptees' Contact with Birth Relatives in Emerging Adulthood

ERIC Educational Resources Information Center

Farr, Rachel H.; Grant-Marsney, Holly A.; Musante, Danila S.; Grotevant, Harold D.; Wrobel, Gretchen Miller

2014-01-01

While openness in adoption has become more common in the United States, little research has examined contact between birth and adoptive families as adoptees become adults. Using quantitative and qualitative data from 167 emerging adult adoptees, factors characterizing contact (e.g., type, frequency, with whom), satisfaction with contact, and the…

Electrical contacts to individual SWCNTs: A review

PubMed Central

Hierold, Christofer; Haluska, Miroslav

2014-01-01

Summary Owing to their superior electrical characteristics, nanometer dimensions and definable lengths, single-walled carbon nanotubes (SWCNTs) are considered as one of the most promising materials for various types of nanodevices. Additionally, they can be used as either passive or active elements. To be integrated into circuitry or devices, they are typically connected with metal leads to provide electrical contacts. The properties and quality of these electrical contacts are important for the function and performance of SWCNT-based devices. Since carbon nanotubes are quasi-one-dimensional structures, contacts to them are different from those for bulk semiconductors. Additionally, some techniques used in Si-based technology are not compatible with SWCNT-based device fabrication, such as the contact area cleaning technique. In this review, an overview of the investigations of metal–SWCNT contacts is presented, including the principle of charge carrier injection through the metal–SWCNT contacts and experimental achievements. The methods for characterizing the electrical contacts are discussed as well. The parameters which influence the contact properties are summarized, mainly focusing on the contact geometry, metal type and the cleanliness of the SWCNT surface affected by the fabrication processes. Moreover, the challenges for widespread application of CNFETs are additionally discussed. PMID:25551048

Geometrical effects of conventional and digital prosthodontic planning wax-ups on lateral occlusal contact number, contact area, and steepness.

PubMed

Abduo, Jaafar

2017-01-01

This study evaluated and compared the effect of conventional and digital wax-ups on three lateral occlusion variables: contact number, contact area, and steepness. Dental casts of 10 patients with Angle Class I relationship were included in the study. All patients required fixed prosthodontic treatment that would affect lateral occlusion. The casts of all patients received conventional and digital wax-ups. For pretreatment, conventional wax-up, and digital wax-up casts, contact number, contact area, and occlusion steepness were measured at four lateral positions, that is, at excursions of 0.5, 1.0, 2.0, and 3.0 mm from maximal intercuspation. Lateral occlusion scheme variables were affected by use of diagnostic wax-ups. For all types of casts, contact number decreased as excursion increased. The two types of wax-ups had similar contact number patterns, and contact number was significantly greater for these casts than for pretreatment casts in the earlier stages of excursion. Similarly, contact area gradually decreased with increasing excursion in the pretreatment and conventional and digital wax-up casts. There was only a minimal decrease in occlusion steepness as excursion increased. However, lateral occlusion was generally steeper for digital wax-up casts.

Nanoscale roughness contact in a slider-disk interface.

PubMed

Hua, Wei; Liu, Bo; Yu, Shengkai; Zhou, Weidong

2009-07-15

The nanoscale roughness contact between molecularly smooth surfaces of a slider-disk interface in a hard disk drive is analyzed, and the lubricant behavior at very high shear rate is presented. A new contact model is developed to study the nanoscale roughness contact behavior by classifying various forms of contact into slider-lubricant contact, slider-disk elastic contact and plastic contact. The contact pressure and the contact probabilities of the three types of contact are investigated. The new contact model is employed to explain and provide insight to an interesting experimental result found in a thermal protrusion slider. The protrusion budget for head surfing in the lubricant, which is the ideal state for contact recording, is also discussed.

Models of epidemics: when contact repetition and clustering should be included

PubMed Central

Smieszek, Timo; Fiebig, Lena; Scholz, Roland W

2009-01-01

Background The spread of infectious disease is determined by biological factors, e.g. the duration of the infectious period, and social factors, e.g. the arrangement of potentially contagious contacts. Repetitiveness and clustering of contacts are known to be relevant factors influencing the transmission of droplet or contact transmitted diseases. However, we do not yet completely know under what conditions repetitiveness and clustering should be included for realistically modelling disease spread. Methods We compare two different types of individual-based models: One assumes random mixing without repetition of contacts, whereas the other assumes that the same contacts repeat day-by-day. The latter exists in two variants, with and without clustering. We systematically test and compare how the total size of an outbreak differs between these model types depending on the key parameters transmission probability, number of contacts per day, duration of the infectious period, different levels of clustering and varying proportions of repetitive contacts. Results The simulation runs under different parameter constellations provide the following results: The difference between both model types is highest for low numbers of contacts per day and low transmission probabilities. The number of contacts and the transmission probability have a higher influence on this difference than the duration of the infectious period. Even when only minor parts of the daily contacts are repetitive and clustered can there be relevant differences compared to a purely random mixing model. Conclusion We show that random mixing models provide acceptable estimates of the total outbreak size if the number of contacts per day is high or if the per-contact transmission probability is high, as seen in typical childhood diseases such as measles. In the case of very short infectious periods, for instance, as in Norovirus, models assuming repeating contacts will also behave similarly as random mixing models. If the number of daily contacts or the transmission probability is low, as assumed for MRSA or Ebola, particular consideration should be given to the actual structure of potentially contagious contacts when designing the model. PMID:19563624

Ultrananocrystalline diamond contacts for electronic devices

DOEpatents

Sumant, Anirudha V.; Smedley, John; Muller, Erik

2016-11-01

A method of forming electrical contacts on a diamond substrate comprises producing a plasma ball using a microwave plasma source in the presence of a mixture of gases. The mixture of gases include a source of a p-type or an n-type dopant. The plasma ball is disposed at a first distance from the diamond substrate. The diamond substrate is maintained at a first temperature. The plasma ball is maintained at the first distance from the diamond substrate for a first time, and a UNCD film, which is doped with at least one of a p-type dopant and an n-type dopant, is disposed on the diamond substrate. The doped UNCD film is patterned to define UNCD electrical contacts on the diamond substrate.

Ultrananocrystalline diamond contacts for electronic devices

DOEpatents

Sumant, Anirudha V.; Smedley, John; Muller, Erik

2017-12-12

A method of forming electrical contacts on a diamond substrate comprises producing a plasma ball using a microwave plasma source in the presence of a mixture of gases. The mixture of gases include a source of a p-type or an n-type dopant. The plasma ball is disposed at a first distance from the diamond substrate. The diamond substrate is maintained at a first temperature. The plasma ball is maintained at the first distance from the diamond substrate for a first time, and a UNCD film, which is doped with at least one of a p-type dopant and an n-type dopant, is disposed on the diamond substrate. The doped UNCD film is patterned to define UNCD electrical contacts on the diamond substrate.

ON Bipolar Cells in Macaque Retina: Type-Specific Synaptic Connectivity with Special Reference to OFF Counterparts

PubMed Central

Tsukamoto, Yoshihiko; Omi, Naoko

2016-01-01

To date, 12 macaque bipolar cell types have been described. This list includes all morphology types first outlined by Polyak (1941) using the Golgi method in the primate retina and subsequently identified by other researchers using electron microscopy (EM) combined with the Golgi method, serial section transmission EM (SSTEM), and immunohistochemical imaging. We used SSTEM for the rod-dense perifoveal area of macaque retina, reconfirmed ON (cone) bipolar cells to be classified as invaginating midget bipolar (IMB), diffuse bipolar (DB)4, DB5, DB6, giant bipolar (GB), and blue bipolar (BB) types, and clarified their type-specific connectivity. DB4 cells made reciprocal synapses with a kind of ON-OFF lateral amacrine cell, similar to OFF DB2 cells. GB cells contacted rods and cones, similar to OFF DB3b cells. Retinal circuits formed by GB and DB3b cells are thought to substantiate the psychophysical finding of fast rod signals in mesopic vision. DB6 cell output synapses were directed to ON midget ganglion (MG) cells at 70% of ribbon contacts, similar to OFF DB1 cells that directed 60% of ribbon contacts to OFF MG cells. IMB cells contacted medium- or long-wavelength sensitive (M/L-) cones but not short-wavelength sensitive (S-) cones, while BB cells contacted S-cones but not M/L-cones. However, IMB and BB dendrites had similar morphological architectures, and a BB cell contacting a single S-cone resembled an IMB cell. Thus, both IMB and BB may be the ON bipolar counterparts of the OFF flat midget bipolar (FMB) type, likewise DB4 of DB2, DB5 of DB3a, DB6 of DB1, and GB of DB3b OFF bipolar type. The ON DB plus GB, and OFF DB cells predominantly contacted M/L-cones and their outputs were directed mainly to parasol ganglion (PG) cells but also moderately to MG cells. BB cells directed S-cone-driven outputs almost exclusively to small bistratified ganglion (SBG) cells. Some FMB cells predominantly contacted S-cones and their outputs were directed to OFF MG cells. Thus, two-step synaptic connections largely narrowed down the S-cone component to SBG and some OFF MG cells. The other OFF MG cells, ON MG cells, and ON and OFF PG cells constructed M/L-cone dominant pathways. PMID:27833534

Schottky barrier tuning of the graphene/SnS2 van der Waals heterostructures through electric field

NASA Astrophysics Data System (ADS)

Zhang, Fang; Li, Wei; Ma, Yaqiang; Dai, Xianqi

2018-03-01

Combining the electronic structures of two-dimensional monolayers in ultrathin hybrid nanocomposites is expected to display new properties beyond their single components. The effects of external electric field (Eext) on the electronic structures of monolayer SnS2 with graphene hybrid heterobilayers are studied by using the first-principle calculations. It is demonstrated that the intrinsic electronic properties of SnS2 and graphene are quite well preserved due to the weak van der Waals (vdW) interactions. We find that the n-type Schottky contacts with the significantly small Schottky barrier are formed at the graphene/SnS2 interface. In the graphene/SnS2 heterostructure, the vertical Eext can control not only the Schottky barriers (n-type and p-type) but also contact types (Schottky contact or Ohmic contact) at the interface. The present study would open a new avenue for application of ultrathin graphene/SnS2 heterostructures in future nano- and optoelectronics.

GaN-based flip-chip LEDs with highly reflective ITO/DBR p-type and via hole-based n-type contacts for enhanced current spreading and light extraction

NASA Astrophysics Data System (ADS)

Zhou, Shengjun; Zheng, Chenju; Lv, Jiajiang; Gao, Yilin; Wang, Ruiqing; Liu, Sheng

2017-07-01

We demonstrate GaN-based double-layer electrode flip-chip light-emitting diodes (DLE-FCLED) with highly reflective indium-tin oxide (ITO)/distributed bragg reflector (DBR) p-type contact and via hole-based n-type contacts. Transparent thin ITO in combination with TiO2/SiO2 DBR is used for reflective p-type ohmic contact, resulting in a significant reduction in absorption of light by opaque metal electrodes. The finely distributed via hole-based n-type contacts are formed on the n-GaN layer by etching via holes through p-GaN and multiple quantum well (MQW) active layer, leading to reduced lateral current spreading length, and hence alleviated current crowding effect. The forward voltage of the DLE-FCLED is 0.31 V lower than that of the top-emitting LED at 90 mA. The light output power of DLE-FCLED is 15.7% and 80.8% higher than that of top-emitting LED at 90 mA and 300 mA, respectively. Compared to top- emitting LED, the external quantum efficiency (EQE) of DLE-FCLED is enhanced by 15.4% and 132% at 90 mA and 300 mA, respectively. The maximum light output power of the DLE-FCLED obtained at 195.6 A/cm2 is 1.33 times larger than that of the top-emitting LED obtained at 93 A/cm2.

Transmission events revealed in tuberculosis contact investigations in London.

PubMed

Cavany, Sean M; Vynnycky, Emilia; Sumner, Tom; Macdonald, Neil; Thomas, H Lucy; White, Jacqui; White, Richard G; Maguire, Helen; Anderson, Charlotte

2018-04-27

Contact tracing is a key part of tuberculosis prevention and care, aiming to hasten diagnosis and prevent transmission. The proportion of case-contact pairs for which recent transmission occurred and the typical timespans between the index case and their contact accessing care are not known; we aimed to calculate these. We analysed individual-level TB contact tracing data, collected in London from 20/01/2011-31/12/2015, linked to tuberculosis surveillance and MIRU-VNTR 24-locus strain-typing information. Of pairs of index cases and contacts diagnosed with active tuberculosis, 85/314 (27%) had strain typing data available for both. Of these pairs, 79% (67/85) shared indistinguishable isolates, implying probable recent transmission. Of pairs in which both contact and the index case had a social risk factor, 11/11 (100%) shared indistinguishable isolates, compared to 55/75 (75%) of pairs in which neither had a social risk factor (P = 0.06). The median time interval between the index case and their contact accessing care was 42 days (IQR: 16, 96). As over 20% of pairs did probably not involve recent transmission between index case and contact, the effectiveness of contact tracing is not necessarily limited to those circumstances where the index case has transmitted disease to their close contacts.

Copper-Based OHMIC Contracts for the Si/SiGe Heterojunction Bipolar Transistor Structure

NASA Technical Reports Server (NTRS)

Das, Kalyan; Hall, Harvey

1999-01-01

Silicon based heterojunction bipolar transistors (HBT) with SiGe base are potentially important devices for high-speed and high-frequency microelectronics. These devices are particularly attractive as they can be fabricated using standard Si processing technology. However, in order to realize the full potential of devices fabricated in this material system, it is essential to be able to form low resistance ohmic contacts using low thermal budget process steps and have full compatibility with VLSI/ULSI processing. Therefore, a study was conducted in order to better understand the contact formation and to develop optimized low resistance contacts to layers with doping densities corresponding to the p-type SiGe base and n-type Si emitter regions of the HBTS. These as-grown doped layers were implanted with BF(sub 2) up to 1 X 10(exp 16)/CM(exp 2) and As up to 5 x 10(exp 15)/CM2, both at 30 keV for the p-type SiGe base and n-type Si emitter layers, respectively, in order to produce a low sheet resistance surface layer. Standard transfer length method (TLM) contact pads on both p and n type layers were deposited using an e-beam evaporated trilayer structure of Ti/CufTi/Al (25)A/1500A/250A/1000A). The TLM pads were delineated by a photoresist lift-off procedure. These contacts in the as-deposited state were ohmic, with specific contact resistances for the highest implant doses of the order of 10(exp -7) ohm-CM2 and lower.

Nanoscale electro-structural characterisation of ohmic contacts formed on p-type implanted 4H-SiC

NASA Astrophysics Data System (ADS)

Frazzetto, Alessia; Giannazzo, Filippo; Lo Nigro, Raffaella; di Franco, Salvatore; Bongiorno, Corrado; Saggio, Mario; Zanetti, Edoardo; Raineri, Vito; Roccaforte, Fabrizio

2011-12-01

This work reports a nanoscale electro-structural characterisation of Ti/Al ohmic contacts formed on p-type Al-implanted silicon carbide (4H-SiC). The morphological and the electrical properties of the Al-implanted layer, annealed at 1700°C with or without a protective capping layer, and of the ohmic contacts were studied using atomic force microscopy [AFM], transmission line model measurements and local current measurements performed with conductive AFM. The characteristics of the contacts were significantly affected by the roughness of the underlying SiC. In particular, the surface roughness of the Al-implanted SiC regions annealed at 1700°C could be strongly reduced using a protective carbon capping layer during annealing. This latter resulted in an improved surface morphology and specific contact resistance of the Ti/Al ohmic contacts formed on these regions. The microstructure of the contacts was monitored by X-ray diffraction analysis and a cross-sectional transmission electron microscopy, and correlated with the electrical results.

Study on the deterioration origin of thermomechanical contact fatigue

NASA Astrophysics Data System (ADS)

Tudose-Sandu-Ville, O. F.

2016-08-01

Thermomechanical wear is a complex phenomenon present in a number of industrial domains, such as rolling bearings, gears, friction wheels, rolling mill rollers. In this type of surface tribological deterioration, both fundamental and some peculiar wears are combined (abrasive, adhesive, corrosive wear and contact fatigue), with mechanical ant thermal causes. The present paper takes into account the contact fatigue type of deterioration, with both causes in mechanical variable load and the thermal tide action on the contact surface. There are some theories synthetically presented regarding the location of critical stresses in rolling contact fatigue. The Jacq thermal effect is briefly presented with some considerations concerning the temperature gradient in the metallic wall. The connection between the Jacq thermal anomaly and the thermomechanical contact fatigue is considered to be a new approach. Also, the same location for both mechanical and thermal critical stresses gives a strong support for the thermomechanical contact fatigue primary deterioration, according to the results obtained during the author's PhD research.

Computerized Generation and Simulation of Meshing and Contact of New Type of Novikov-Wildhaber Helical Gears

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Feng, Pin-Hao; Lagutin, Sergei A.

2000-01-01

In this report, we propose a new geometry for low-noise, increased-strength helical gears of the Novikov-Wildhaber type. Contact stresses are reduced as a result of their convex-concave gear tooth surfaces. The gear tooth surfaces are crowned in the profile direction to localize bearing contact and in the longitudinal direction to obtain a parabolic function of transmission errors. Such a function results in the reduction of noise and vibrations. Methods for the generation of the proposed gear tooth surfaces by grinding and hobbing are considered, and a tooth contact analysis (TCA) computer program to simulate meshing and contact is applied. The report also investigates the influence of misalignment on transmission errors and shift of bearing contact. Numerical examples to illustrate the developed approaches are proposed. The proposed geometry was patented by Ford/UIC (Serial Number 09-340-824, pending) on June 28, 1999.

Characteristics of signals originating near the lithium-diffused N+ contact of high purity germanium p-type point contact detectors

DOE PAGES

Aguayo, E.; Amman, M.; Avignone, F. T.; ...

2012-11-09

A study of signals originating near the lithium-diffused n+ contact of p-type point contact (PPC) high purity germanium detectors (HPGe) is presented. The transition region between the active germanium and the fully dead layer of the n+ contact is examined. Energy depositions in this transition region are shown to result in partial charge collection. This provides a mechanism for events with a well defined energy to contribute to the continuum of the energy spectrum at lower energies. A novel technique to quantify the contribution from this source of background is introduced. Furthermore, experiments that operate germanium detectors with a verymore » low energy threshold may benefit from the methods presented herein.« less

Patello-femoral and tibio-femoral contact forces during kicking type of activity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Engin, A.E.; Tumer, S.T.

1996-12-31

In this paper patello-femoral and tibia-femoral contact forces during kicking type of activity is presented by means of a dynamic model of the knee joint which includes tibio-femoral and patello-femoral articulations, and the major ligaments of the joint. The model shows that the patella can be subjected to very large transient patello-femoral contact forces during a strenuous lower limb activity such as kicking even under conditions of small knee-flexion angles.

Atomistic study of the electronic contact resistivity between the half-Heusler alloys (HfCoSb, HfZrCoSb, HfZrNiSn) and the metal Ag

NASA Astrophysics Data System (ADS)

He, Yuping; Léonard, François; Spataru, Catalin D.

2018-06-01

Half-Heusler (HH) alloys have shown promising thermoelectric properties in the medium- and high-temperature range. To harness these material properties for thermoelectric applications, it is important to realize electrical contacts with low electrical contact resistivity. However, little is known about the detailed structural and electronic properties of such contacts and the expected values of contact resistivity. Here, we employ atomistic ab initio calculations to study electrical contacts in a subclass of HH alloys consisting of the compounds HfCoSb, HfZrCoSb, and HfZrNiSn. By using Ag as a prototypical metal, we show that the termination of the HH material critically determines the presence or absence of strong deformations at the interface. Our study includes contacts to doped materials, and the results indicate that the p -type materials generally form ohmic contacts while the n -type materials have a small Schottky barrier. We calculate the temperature dependence of the contact resistivity in the low- to medium-temperature range and provide quantitative values that set lower limits for these systems.

UMA/GAN network architecture analysis

NASA Astrophysics Data System (ADS)

Yang, Liang; Li, Wensheng; Deng, Chunjian; Lv, Yi

2009-07-01

This paper is to critically analyze the architecture of UMA which is one of Fix Mobile Convergence (FMC) solutions, and also included by the third generation partnership project(3GPP). In UMA/GAN network architecture, UMA Network Controller (UNC) is the key equipment which connects with cellular core network and mobile station (MS). UMA network could be easily integrated into the existing cellular networks without influencing mobile core network, and could provides high-quality mobile services with preferentially priced indoor voice and data usage. This helps to improve subscriber's experience. On the other hand, UMA/GAN architecture helps to integrate other radio technique into cellular network which includes WiFi, Bluetooth, and WiMax and so on. This offers the traditional mobile operators an opportunity to integrate WiMax technique into cellular network. In the end of this article, we also give an analysis of potential influence on the cellular core networks ,which is pulled by UMA network.

Thin film photovoltaic device

DOEpatents

Catalano, Anthony W.; Bhushan, Manjul

1982-01-01

A thin film photovoltaic solar cell which utilizes a zinc phosphide semiconductor is of the homojunction type comprising an n-type conductivity region forming an electrical junction with a p-type region, both regions consisting essentially of the same semiconductor material. The n-type region is formed by treating zinc phosphide with an extrinsic dopant such as magnesium. The semiconductor is formed on a multilayer substrate which acts as an opaque contact. Various transparent contacts may be used, including a thin metal film of the same chemical composition as the n-type dopant or conductive oxides or metal grids.

A Student Profile.

ERIC Educational Resources Information Center

Maine Univ., Augusta.

A survey of graduates and students from the University of Maine at Augusta (UMA) was conducted in Spring 1980 to provide a profile of new and continuing students and to assess the vocational success of recent UMA graduates. The survey sample included: (1) 461 students selected from the entire UMA population; (2) 49 students enrolled in UMA's…

Observations and light curve solutions of three ultrashort-period W UMa binaries

NASA Astrophysics Data System (ADS)

Kjurkchieva, Diana P.; Michel, Raul; Popov, Velimir A.; Deras, Dan

2018-07-01

Photometric observations in V, Rc and Ic bands of the ultrashort-period W UMa binaries 1SWASP J044132.96+440613.7, 1SWASP J052926.88+461147.5 and NSVS 2175434 are presented. The results from the modeling and analysis of our observations reveal that: (i) All targets undergo total eclipses and their photometric mass ratios should be accepted with confidence; (ii) All stellar components are late-type dwarfs; (iii) The temperature difference of target components does not exceed 150 K; (iv) All targets have overcontact configurations with fill-out factor around 0.24; (v) The orbit of NSVS 2175434 is slightly eccentric which is unusual for such an ultrashort-period binary; (vi) The orbital periods of all targets were improved. Masses, radii and luminosities of the stellar components were estimated by the empirical relation "period, orbital axis" for short- and ultrashort-period binaries.

Classification of Domain Movements in Proteins Using Dynamic Contact Graphs

PubMed Central

Taylor, Daniel; Cawley, Gavin; Hayward, Steven

2013-01-01

A new method for the classification of domain movements in proteins is described and applied to 1822 pairs of structures from the Protein Data Bank that represent a domain movement in two-domain proteins. The method is based on changes in contacts between residues from the two domains in moving from one conformation to the other. We argue that there are five types of elemental contact changes and that these relate to five model domain movements called: “free”, “open-closed”, “anchored”, “sliding-twist”, and “see-saw.” A directed graph is introduced called the “Dynamic Contact Graph” which represents the contact changes in a domain movement. In many cases a graph, or part of a graph, provides a clear visual metaphor for the movement it represents and is a motif that can be easily recognised. The Dynamic Contact Graphs are often comprised of disconnected subgraphs indicating independent regions which may play different roles in the domain movement. The Dynamic Contact Graph for each domain movement is decomposed into elemental Dynamic Contact Graphs, those that represent elemental contact changes, allowing us to count the number of instances of each type of elemental contact change in the domain movement. This naturally leads to sixteen classes into which the 1822 domain movements are classified. PMID:24260562

Tuning the Schottky barrier in the arsenene/graphene van der Waals heterostructures by electric field

NASA Astrophysics Data System (ADS)

Li, Wei; Wang, Tian-Xing; Dai, Xian-Qi; Wang, Xiao-Long; Ma, Ya-Qiang; Chang, Shan-Shan; Tang, Ya-Nan

2017-04-01

Using density functional theory calculations, we investigate the electronic properties of arsenene/graphene van der Waals (vdW) heterostructures by applying external electric field perpendicular to the layers. It is demonstrated that weak vdW interactions dominate between arsenene and graphene with their intrinsic electronic properties preserved. We find that an n-type Schottky contact is formed at the arsenene/graphene interface with a Schottky barrier of 0.54 eV. Moreover, the vertical electric field can not only control the Schottky barrier height but also the Schottky contacts (n-type and p-type) and Ohmic contacts (n-type) at the interface. Tunable p-type doping in graphene is achieved under the negative electric field because electrons can transfer from the Dirac point of graphene to the conduction band of arsenene. The present study would open a new avenue for application of ultrathin arsenene/graphene heterostructures in future nano- and optoelectronics.

Genotypic characteristics of Mycobacterium tuberculosis isolated from household contacts of tuberculosis patients in the Philippines.

PubMed

Sia, Irene G; Buckwalter, Seanne P; Doerr, Kelly A; Lugos, Sonia; Kramer, Rebecca; Orillaza-Chi, Ruth; Quelapio, Maria Imelda; Tupasi, Thelma E; Wengenack, Nancy L

2013-12-05

The Philippines has an extremely high rate of tuberculosis but little is known about M. tuberculosis genotypes and transmission dynamics in this country. The aim of this study was to determine the proportion of household contacts who develop active TB due to direct transmission from an index case in that household. Mycobacterium tuberculosis isolates from household contacts of tuberculosis patients in the Philippines were characterized using restriction-fragment-length polymorphism analysis, spoligotyping, and mycobacterial interspersed repetitive units - variable number tandem repeats typing (12-loci) to determine their utility in elucidating transmission in an area of high tuberculosis prevalence. Drug susceptibility patterns for these isolates were also determined. Spoligotyping and MIRU-VNTR typing results matched in 10 (62.5%) of 16 index patient-household contact pairs while IS6110 fingerprints matched in only six (37.5%) pairs. Only 3/16 (18.8%) index patient-household contact pairs had identical drug susceptibility results. Strain typing of M. tuberculosis isolates from household contacts in the Philippines indicates that transmission of strains does not necessarily occur directly from the index patient living in close proximity in the same household but rather that community-based transmission also frequently occurs. Accurate susceptibility testing of all isolates is necessary to insure optimal care of both the index patients and any culture-positive household contacts.

Direct physical contact between intercalated cells in the distal convoluted tubule and the afferent arteriole in mouse kidneys.

PubMed

Ren, Hao; Liu, Ning-Yu; Andreasen, Arne; Thomsen, Jesper S; Cao, Liu; Christensen, Erik I; Zhai, Xiao-Yue

2013-01-01

Recent physiological studies in the kidney proposed the existence of a secondary feedback mechanism termed 'crosstalk' localized after the macula densa. This newly discovered crosstalk contact between the nephron tubule and its own afferent arteriole may potentially revolutionize our understanding of renal vascular resistance and electrolyte regulation. However, the nature of such a crosstalk mechanism is still debated due to a lack of direct and comprehensive morphological evidence. Its exact location along the nephron, its prevalence among the different types of nephrons, and the type of cells involved are yet unknown. To address these issues, computer assisted 3-dimensional nephron tracing was applied in combination with direct immunohistochemistry on plastic sections and electron microscopy. 'Random' contacts in the cortex were identified by the tracing and excluded. We investigated a total of 168 nephrons from all cortical regions. The results demonstrated that the crosstalk contact existed, and that it was only present in certain nephrons (90% of the short-looped and 75% of the long-looped nephrons). The crosstalk contacts always occurred at a specific position--the last 10% of the distal convoluted tubule. Importantly, we demonstrated, for the first time, that the cells found in the tubule wall at the contact site were always type nonA-nonB intercalated cells. In conclusion, the present work confirmed the existence of a post macula densa physical crosstalk contact.

Unipolar n-Type Black Phosphorus Transistors with Low Work Function Contacts.

PubMed

Wang, Ching-Hua; Incorvia, Jean Anne C; McClellan, Connor J; Yu, Andrew C; Mleczko, Michal J; Pop, Eric; Wong, H-S Philip

2018-05-09

Black phosphorus (BP) is a promising two-dimensional (2D) material for nanoscale transistors, due to its expected higher mobility than other 2D semiconductors. While most studies have reported ambipolar BP with a stronger p-type transport, it is important to fabricate both unipolar p- and n-type transistors for low-power digital circuits. Here, we report unipolar n-type BP transistors with low work function Sc and Er contacts, demonstrating a record high n-type current of 200 μA/μm in 6.5 nm thick BP. Intriguingly, the electrical transport of the as-fabricated, capped devices changes from ambipolar to n-type unipolar behavior after a month at room temperature. Transmission electron microscopy analysis of the contact cross-section reveals an intermixing layer consisting of partly oxidized metal at the interface. This intermixing layer results in a low n-type Schottky barrier between Sc and BP, leading to the unipolar behavior of the BP transistor. This unipolar transport with a suppressed p-type current is favorable for digital logic circuits to ensure a lower off-power consumption.

Formation of gallium vacancies and their effects on the nanostructure of Pd/Ir/Au ohmic contact to p-type GaN.

PubMed

Kim, Kyong Nam; Kim, Tae Hyung; Seo, Jin Seok; Kim, Ki Seok; Bae, Jeong Woon; Yeom, Geun Young

2013-12-01

The properties of Pd/Ir/Au ohmic metallization on p-type GaN have been investigated. Contacts annealed at 400 degrees C in O2 atmosphere demonstrated excellent ohmic characteristics with a specific contact resistivity of 1.5 x 10(-5) Omega-cm2. This is attributed to the formation of Ga vacancies at the contact metal-semiconductor interfacial region due to the out-diffusion of Ga atoms. The out-diffusion of Ga atoms was confirmed by X-ray photoelectron spectroscopy depth profiles, high-resolution transmission electron microscopy, and electron energy loss spectroscopy using a scanning transmission electron microscope.

Photovoltaic solar cell

DOEpatents

Nielson, Gregory N; Cruz-Campa, Jose Luis; Okandan, Murat; Resnick, Paul J

2014-05-20

A photovoltaic solar cell for generating electricity from sunlight is disclosed. The photovoltaic solar cell comprises a plurality of spaced-apart point contact junctions formed in a semiconductor body to receive the sunlight and generate the electricity therefrom, the plurality of spaced-apart point contact junctions having a first plurality of regions having a first doping type and a second plurality of regions having a second doping type. In addition, the photovoltaic solar cell comprises a first electrical contact electrically connected to each of the first plurality of regions and a second electrical contact electrically connected to each of the second plurality of regions, as well as a passivation layer covering major surfaces and sidewalls of the photovoltaic solar cell.

Photovoltaic solar cell

DOEpatents

Nielson, Gregory N; Okandan, Murat; Cruz-Campa, Jose Luis; Resnick, Paul J

2013-11-26

A photovoltaic solar cell for generating electricity from sunlight is disclosed. The photovoltaic solar cell comprises a plurality of spaced-apart point contact junctions formed in a semiconductor body to receive the sunlight and generate the electicity therefrom, the plurality of spaced-apart point contact junctions having a first plurality of regions having a first doping type and a second plurality of regions having a second doping type. In addition, the photovoltaic solar cell comprises a first electrical contact electrically connected to each of the first plurality of regions and a second electrical contact electrically connected to each of the second plurality of regions, as well as a passivation layer covering major surfaces and sidewalls of the photovoltaic solar cell.

Formation and characterization of Ni/Al Ohmic contact on n+-type GeSn

NASA Astrophysics Data System (ADS)

Zhang, Xu; Zhang, Dongliang; Zheng, Jun; Liu, Zhi; He, Chao; Xue, Chunlai; Zhang, Guangze; Li, Chuanbo; Cheng, Buwen; Wang, Qiming

2015-12-01

In this study, a Ni/Al Ohmic contact on a highly doped n-type GeSn has been investigated. A specific contact resistivity as low as (2.26 ± 0.11) × 10-4 Ω cm2 was obtained with the GeSn sample annealed at a temperature of 450 °C for 30 s. The linear Ohmic behavior was attributed to the low resistance of the Ni(GeSn) phase; this behavior was determined using glancing-angle X-ray diffraction, and the quantum tunneling current through the Schottky barrier narrowed because of high doping; this phenomenon was confirmed from the contact resistance characteristics at different temperatures from 45 to 205 K.

Compression and contact area of anterior strut grafts in spinal instrumentation: a biomechanical study.

PubMed

Pizanis, Antonius; Holstein, Jörg H; Vossen, Felix; Burkhardt, Markus; Pohlemann, Tim

2013-08-26

Anterior bone grafts are used as struts to reconstruct the anterior column of the spine in kyphosis or following injury. An incomplete fusion can lead to later correction losses and compromise further healing. Despite the different stabilizing techniques that have evolved, from posterior or anterior fixating implants to combined anterior/posterior instrumentation, graft pseudarthrosis rates remain an important concern. Furthermore, the need for additional anterior implant fixation is still controversial. In this bench-top study, we focused on the graft-bone interface under various conditions, using two simulated spinal injury models and common surgical fixation techniques to investigate the effect of implant-mediated compression and contact on the anterior graft. Calf spines were stabilised with posterior internal fixators. The wooden blocks as substitutes for strut grafts were impacted using a "pressfit" technique and pressure-sensitive films placed at the interface between the vertebral bone and the graft to record the compression force and the contact area with various stabilization techniques. Compression was achieved either with posterior internal fixator alone or with an additional anterior implant. The importance of concomitant ligament damage was also considered using two simulated injury models: pure compression Magerl/AO fracture type A or rotation/translation fracture type C models. In type A injury models, 1 mm-oversized grafts for impaction grafting provided good compression and fair contact areas that were both markedly increased by the use of additional compressing anterior rods or by shortening the posterior fixator construct. Anterior instrumentation by itself had similar effects. For type C injuries, dramatic differences were observed between the techniques, as there was a net decrease in compression and an inadequate contact on the graft occurred in this model. Under these circumstances, both compression and the contact area on graft could only be maintained at high levels with the use of additional anterior rods. Under experimental conditions, we observed that ligamentous injury following type C fracture has a negative influence on the compression and contact area of anterior interbody bone grafts when only an internal fixator is used for stabilization. Because of the loss of tension banding effects in type C injuries, an additional anterior compressing implant can be beneficial to restore both compression to and contact on the strut graft.

Wear of seal materials used in aircraft propulsion systems

NASA Technical Reports Server (NTRS)

Bill, R. C.; Ludwig, L. P.

1978-01-01

The various types of seal locations in a gas turbine engine are described, and the significance of wear to each type is reviewed. Starting with positive contact shaft seals, existing material selection guidelines are reviewed, and the existing PV (contact pressure X sliding velocity) criteria for selecting seal materials are discussed, along with the theoretical background for these criteria. Examples of wear mechanisms observed to operate in positive contact seals are shown. Design features that can extend the operating capabilities of positive contact seals, including pressure balancing and incorporation of hydrodynamic lift are briefly discussed. It is concluded that, despite the benefits arising from these design features, improved positive contact seal materials from the standpoint of wear, erosion and oxidation resistance will be necessary for further improvements in seal performance and durability, and to meet stringent future challenges.

Controlling interface oxygen for forming Ag ohmic contact to semi-polar (1 1 -2 2) plane p-type GaN

NASA Astrophysics Data System (ADS)

Park, Jae-Seong; Han, Jaecheon; Seong, Tae-Yeon

2014-11-01

Low-resistance Ag ohmic contacts to semi-polar (1 1 -2 2) p-GaN were developed by controlling interfacial oxide using a Zn layer. The 300 °C-annealed Zn/Ag samples showed ohmic behavior with a contact resistivity of 6.0 × 10-4 Ω cm2 better than that of Ag-only contacts (1.0 × 10-3 Ω cm2). The X-ray photoemission spectroscopy (XPS) results showed that annealing caused the indiffusion of oxygen at the contact/GaN interface, resulting in the formation of different types of interfacial oxides, viz. Ga-oxide and Ga-doped ZnO. Based on the XPS and electrical results, the possible mechanisms underlying the improved electrical properties of the Zn/Ag samples are discussed.

Metamorphic assemblages and the direction of flow of metamorphic fluids in four instances of serpentinization

USGS Publications Warehouse

Barnes, I.; Rapp, J.B.; O'Neil, J.R.; Sheppard, R.A.; Gude, A.J.

1972-01-01

Fluids related to Serpentinization are of at least three types. The first reported (Barnes and O'Neil, 1969) is a fluid of local meteoric origin, the chemical and thermodynamic properties of which are entirely controlled by olivine, orthopyroxene, brucite, and serpentine reactions. It is a Ca+2-OH-1 type and is shown experimentally to be capable of reacting with albite to yield calcium hydroxy silicates. Rodingites may form where the Ca+2-OH-1 type waters flow across the ultramafic contact and react with siliceous country rock. The second type of fluid has its chemical composition largely controlled before it enters the ultramafic rocks, but reactions within the ultramafic rocks fix the thermodynamic properties by reactions of orthopyroxene, olivine, calcite, brucite, and serpentine. The precipitation of brucite from this fluid clearly shows that fluid flow allows reaction products to be deposited at a distance from the point of solution. Thus, textural evidence for volume relations during Serpentinization may not be valid. The third type of fluid has its chemical properties fixed in part before the reactions with ultramafic rocks, in part by the reactions of orthopyroxene, olivine, and serpentine and in part by reactions with siliceous country rock at the contact. The reactions of the ultramafic rock and country rock with the fluid must be contemporaneous and require flow to be along the contact. This third type of fluid is grossly supersaturated with talc and tremolite, both found along the contact. The occurrence of magadiite, kenyaite, mountainite, and rhodesite along the contact is probably due to a late stage low-temperature reaction of fluids of the same thermodynamic properties as those that formed the talc and tremolite at higher temperatures. Oxygen isotope analyses of some of these minerals supports this conclusion. Rodingites form from Ca+2-rich fluids flowing across the contact; talc and tremolite form from silica-rich fluids flowing along the contact. Isotopic analyses of the fluids indicate varied origins including unaltered local meteoric water and connate water. Complexion Spring water may be a sample of only slightly altered Jurassic or Cretaceous sea water. ?? 1972 Springer-Verlag.

49 CFR 236.560 - Contact element, mechanical trip type; location with respect to rail.

Code of Federal Regulations, 2011 CFR

2011-10-01

... INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Rules and.... Contact element of automatic train stop device of the mechanical trip type shall be maintained at a height...

Structure of welded joints obtained by contact weld in nanostructured titanium

NASA Astrophysics Data System (ADS)

Klimenov, V. A.; Klopotov, A. A.; Gnysov, S. F.; Vlasov, V. A.; Lychagin, D. V.; Chumaevskii, A. V.

2015-10-01

The paper presents the research of the weld structure of two Ti specimens of the type VT6 that have nano- and submicrocrystalline structures. Electrical contact welding is used to obtain welds. The acicular structure is formed in the weld area. Two types of defects are detected, namely micropores and microcracks.

Studies of intercellular invasion in vitro using rabbit peritoneal neutrophil granulocytes (PMNS). I. Role of contact inhibition of locomotion

PubMed Central

1975-01-01

Intercellular invasion is the active migration of cells on one type into the interiors of tissues composed of cells of dissimilar cell types. Contact paralysis of locomotion is the cessation of forward extension of the pseudopods of a cell as a result of its collision with another cell. One hypothesis to account for intercellular invasion proposes that a necessary condition for a cell type to be invasive to a given host tissue is that it lack contact paralysis of locomotion during collision with cells of that host tissue. The hypothesis has been tested using rabbit peritoneal neutrophil granulocytes (PMNs) as the invasive cell type and chick embryo fibroblasts as the host tissue. In organ culture, PMNs rapidly invade aggregates of fibroblasts. The behavior of the pseudopods of PMNs during collision with fibroblasts was analyzed for contact paralysis by a study of time-lapse films of cells in mixed monolayer culture. In monolayer culture, PMNs show little sign of paralysis of the pseudopods upon collision with fibroblasts and thus conform in their behavior to that predicted by the hypothesis. PMID:1092702

IX Draconis - a curious ER UMa-type dwarf nova

NASA Astrophysics Data System (ADS)

Otulakowska-Hypka, M.; Olech, A.; de Miguel, E.; Rutkowski, A.; Koff, R.; Bąkowska, K.

2013-02-01

We report results of an extensive worldwide observing campaign devoted to a very active dwarf nova star - IX Draconis. We investigated photometric behaviour of the system to derive its basic outburst properties and understand peculiarities of IX Draconis as well as other active cataclysmic variables, in particular dwarf novae of the ER UMa type. In order to measure fundamental parameters of the system, we carried out analyses of the light curve, O - C diagram, and power spectra. During over two months of observations, we detected two superoutbursts and several normal outbursts. The V magnitude of the star varied in the range 14.6-18.2 mag. Superoutbursts occur regularly with the supercycle length (Psc) of 58.5 ± 0.5 d. When analysing data over the past 20 years, we found that Psc is increasing at a rate of dot{P} = 1.8 × 10^{-3}. Normal outbursts appear to be irregular, with typical occurrence times in the range 3.1-4.1 d. We detected a double-peaked structure of superhumps during superoutburst, with the secondary maximum becoming dominant near the end of the superoutburst. The mean superhump period observed during superoutbursts is Psh = 0.066982(36) d (96.45 ± 0.05 min), which is constant over the last two decades of observations. Based on the power spectrum analysis, the evaluation of the orbital period was problematic. We found two possible values: the first one, 0.066 41(3) d (95.63 ± 0.04 min), which is in agreement with previous studies and our O - C analysis [0.06646(2) d, 95.70 ± 0.03 min], and the second one, 0.06482(3) d (93.34 ± 0.04 min), which is less likely. The evolutionary status of the object depends dramatically on the choice between these two values. A spectroscopic determination of the orbital period is needed. We updated available information on ER UMa-type stars and present a new set of their basic statistics. Thereby, we provide evidence that this class of stars is not uniform.

Electrical, structural and surface morphological properties of thermally stable low-resistance W/Ti/Au multilayer ohmic contacts to n-type GaN

NASA Astrophysics Data System (ADS)

Jyothi, I.; Reddy, V. Rajagopal

2010-10-01

A W/Ti/Au multilayer scheme has been fabricated for achieving thermally stable low-resistance ohmic contact to n-type GaN (4.0 × 10 18 cm -3). It is shown that the as-deposited W/Ti/Au contact exhibits near linear I- V behaviour. However, annealing at temperature below 800 °C the contacts exhibit non-linear behaviour. After annealing at a temperature in excess of 850 °C, the W/Ti/Au contact showed ohmic behaviour. The W/Ti/Au contact produced specific contact resistance as low as 6.7 × 10 -6 Ω cm 2 after annealing at 900 °C for 1 min in a N 2 ambient. It is noted that the specific contact resistance decreases with increase in annealing temperature. It is also noted that annealing the contacts at 900 °C for 30 min causes insignificant degradation of the electrical and thermal properties. It is further shown that the overall surface morphology of the W/Ti/Au stayed fairly smooth even after annealing at 900 °C. The W/Ti/Au ohmic contact showed good edge sharpness after annealing at 900 °C for 30 min. Based on the Auger electron spectroscopy and glancing angle X-ray diffraction results, possible explanation for the annealing dependence of the specific contact resistance of the W/Ti/Au contacts are described and discussed.

Development of high temperature stable Ohmic and Schottky contacts on n-gallium nitride

NASA Astrophysics Data System (ADS)

Khanna, Rohit

In this work the effort was made to towards develop and investigate high temperature stable Ohmic and Schottky contacts for n type GaN. Various borides and refractory materials were incorporated in metallization scheme to best attain the desired effect of minimal degradation of contacts when placed at high temperatures. This work focuses on achieving a contact scheme using different borides which include two Tungsten Borides (namely W2B, W2B 5), Titanium Boride (TiB2), Chromium Boride (CrB2) and Zirconium Boride (ZrB2). Further a high temperature metal namely Iridium (Ir) was evaluated as a potential contact to n-GaN, as part of continuing improved device technology development. The main goal of this project was to investigate the most promising boride-based contact metallurgies on GaN, and finally to fabricate a High Electron Mobility Transistor (HEMT) and compare its reliability to a HEMT using present technology contact. Ohmic contacts were fabricated on n GaN using borides in the metallization scheme of Ti/Al/boride/Ti/Au. The characterization of the contacts was done using current-voltage measurements, scanning electron microscopy (SEM) and Auger Electron Spectroscopy (AES) measurements. The contacts formed gave specific contact resistance of the order of 10-5 to 10-6 Ohm-cm2. A minimum contact resistance of 1.5x10-6 O.cm 2 was achieved for the TiB2 based scheme at an annealing temperature of 850-900°C, which was comparable to a regular ohmic contact of Ti/Al/Ni/Au on n GaN. When some of borides contacts were placed on a hot plate or in hot oven for temperature ranging from 200°C to 350°C, the regular metallization contacts degraded before than borides ones. Even with a certain amount of intermixing of the metallization scheme the boride contacts showed minimal roughening and smoother morphology, which, in terms of edge acuity, is crucial for very small gate devices. Schottky contacts were also fabricated and characterized using all the five boride compounds. The barrier height obtained on n GaN was ˜0-5-0.6 eV which was low compared to those obtained by Pt or Ni. This barrier height is too low for use as a gate contact and they can only have limited use, perhaps, in gas sensors where large leakage current can be tolerated in exchange for better thermal reliability. AlGaN/GaN High Electron Mobility Transistors (HEMTs) were fabricated with Ti/Al/TiB2/Ti/Au source/drain ohmic contacts and a variety of gate metal schemes (Pt/Au, Ni/Au, Pt/TiB2/Au or Ni/TiB 2/Au) and were subjected to long-term annealing at 350°C. By comparison with companion devices with conventional Ti/Al/Pt/Au ohmic contacts and Pt/Au gate contacts, the HEMTs with boride-based ohmic metal and either Pt/Au, Ni/Au or Ni/TiB2/Au gate metal showed superior stability of both source-drain current and transconductance after 25 days aging at 350°C. The need for sputter deposition of the borides causes' problem in achieving significantly lower specific contact resistance than with conventional schemes deposited using e-beam evaporation. The borides also seem to be, in general, good getters for oxygen leading to sheet resistivity issues. Ir/Au Schottky contacts and Ti/Al/Ir/Au ohmic contacts on n-type GaN were investigated as a function of annealing temperature and compared to their more common Ni-based counterparts. The Ir/Au ohmic contacts on n-type GaN with n˜1017 cm-3 exhibited barrier heights of 0.55 eV after annealing at 700°C and displayed less intermixing of the contact metals compared to Ni/Au. A minimum specific contact resistance of 1.6 x 10-6 O.cm2 was obtained for the ohmic contacts on n-type GaN with n˜1018 cm-3 after annealing at 900°C. The measurement temperature dependence of contact resistance was similar for both Ti/Al/Ir/Au and Ti/Al/Ni/Au, suggesting the same transport mechanism was present in both types of contacts. The Ir-based ohmic contacts displayed superior thermal aging characteristics at 350°C. Auger Electron Spectroscopy showed that Ir is a superior diffusion barrier at these moderate temperatures than Ni.

Analysis of charge injection and contact resistance as a function of electrode surface treatment in ambipolar polymer transistors

NASA Astrophysics Data System (ADS)

Lee, Seon Jeng; Kim, Chaewon; Jung, Seok-Heon; Di Pietro, Riccardo; Lee, Jin-Kyun; Kim, Jiyoung; Kim, Miso; Lee, Mi Jung

2018-01-01

Ambipolar organic field-effect transistors (OFETs) have both of hole and electron enhancements in charge transport. The characteristics of conjugated diketopyrrolopyrrole ambipolar OFETs depend on the metal-contact surface treatment for charge injection. To investigate the charge-injection characteristics of ambipolar transistors, these devices are processed via various types of self-assembled monolayer treatments and annealing. We conclude that treatment by the self-assembled monolayer 1-decanethiol gives the best enhancement of electron charge injection at both 100 and 300 °C annealing temperature. In addition, the contact resistance is calculated by using two methods: One is the gated four-point probe (gFPP) method that gives the voltage drop between channels, and the other is the simultaneous contact resistance extraction method, which extracts the contact resistance from the general transfer curve. We confirm that the gFPP method and the simultaneous extraction method give similar contact resistance, which means that we can extract contact resistance from the general transfer curve without any special contact pattern. Based on these characteristics of ambipolar p- and n-type transistors, we fabricate inverter devices with only one active layer. [Figure not available: see fulltext.

Allergic Contact Dermatitis (Type IV Hypersensitivity) and Type I Hypersensitivity Following Aromatherapy with Ayurvedic Oils (Dhanwantharam Thailam, Eladi Coconut Oil) Presenting as Generalized Erythema and Pruritus with Flexural Eczema.

PubMed

Lakshmi, Chembolli

2014-05-01

Herbal and Ayurvedic medications, believed to be "mild" and "natural" are usually sought as the first line of treatment before resorting to "stronger" allopathic medication. There are very few reports of adverse reactions to either topical and/or systemic Ayurvedic medications. Massage aromatherapy with ayurvedic oils plays an important role in alleviation of pain, but may cause allergic contact dermatitis. This is the second case report of allergic contact dermatitis to ayurvedic oil.

INTERNATIONAL CONFERENCE ON SEMICONDUCTOR INJECTION LASERS SELCO-87: Multilayer CrPtCr/NiAu ohmic contacts with p-type GaAs in heterojunction laser structures

NASA Astrophysics Data System (ADS)

Wójcik, I.; Stareev, G.; Barcz, A.; Domański, M.

1988-11-01

Multilayer CrPtCr/NiAu metallization was deposited by sputtering in a magnetron on the p-type side of GaAs in a pulsed laser heterostructure. Heat treatment at 490 °C for 3 min produced a reliable ohmic contact with a specific resistance of 10- 6-10- 5 Ω · cm2, depending on the substrate doping. Secondary-ion mass spectroscopy and Rutherford backscattering methods were used to study the mechanism of formation of a contact.

Thin film photovoltaic device

DOEpatents

Catalano, A.W.; Bhushan, M.

1982-08-03

A thin film photovoltaic solar cell which utilizes a zinc phosphide semiconductor is of the homojunction type comprising an n-type conductivity region forming an electrical junction with a p-type region, both regions consisting essentially of the same semiconductor material. The n-type region is formed by treating zinc phosphide with an extrinsic dopant such as magnesium. The semiconductor is formed on a multilayer substrate which acts as an opaque contact. Various transparent contacts may be used, including a thin metal film of the same chemical composition as the n-type dopant or conductive oxides or metal grids. 5 figs.

Poor correlation between the removal or deposition of pollen grains and frequency of pollinator contact with sex organs

NASA Astrophysics Data System (ADS)

Sakamoto, Ryota L.; Morinaga, Shin-Ichi

2013-09-01

Pollinators deposit pollen grains on stigmas and remove pollen grains from anthers. The mechanics of these transfers can now be quantified with the use of high-speed video. We videoed hawkmoths, carpenter bees, and swallowtail butterflies pollinating Clerodendrum trichotomum. The number of grains deposited on stigmas did not vary significantly with the number of times pollinators contacted stigmas. In contrast, pollen removal from the anthers increased significantly with the number of contacts to anthers. Pollen removal varied among the three types of pollinators. Also, the three types carried pollen on different parts of their bodies. In hawkmoths and carpenter bees, a large number of contacted body part with anthers differed significantly from the body part that attached a large number of pollen grains. Our results indicate that a large number of contacts by pollinators does not increase either the male or female reproductive success of plants compared to a small number of contacts during a visit.

Mixed ternary heterojunction solar cell

DOEpatents

Chen, Wen S.; Stewart, John M.

1992-08-25

A thin film heterojunction solar cell and a method of making it has a p-type layer of mixed ternary I-III-VI.sub.2 semiconductor material in contact with an n-type layer of mixed binary II-VI semiconductor material. The p-type semiconductor material includes a low resistivity copper-rich region adjacent the back metal contact of the cell and a composition gradient providing a minority carrier mirror that improves the photovoltaic performance of the cell. The p-type semiconductor material preferably is CuInGaSe.sub.2 or CuIn(SSe).sub.2.

CCD Photometry and Roche Modeling of the Eclipsing Deep Low Mass, Overcontact Binary Star System TYC 2058-753-1

NASA Astrophysics Data System (ADS)

Alton, K. B.

2018-06-01

Abstract TYC 2058-753-1 (NSVS 7903497; ASAS 165139+2255.7) is a W UMa binary system (P = 0.353205 d) which has not been rigorously studied since first being detected nearly 15 years ago by the ROTSE-I telescope. Other than the unfiltered ROTSE-I and monochromatic All Sky Automated Survey (ASAS) survey data, no multi-colored light curves (LC) have been published. Photometric data collected in three bandpasses (B, V, and Ic) at Desert Bloom Observatory in June 2017 produced six times-of-minimum for TYC 2058-753-1 which were used to establish a linear ephemeris from the first directly measured Min I epoch (HJD0). No published radial velocity data are available for this system, however, since this W UMa binary undergoes a very obvious total eclipse, Roche modeling produced a well-constrained photometric value for the mass ratio (qph = 0.103 ± 0.001). This low-mass ratio binary star system also exhibits a high degree of contact (f > 56%). There is a suggestion from the ROTSE-I and ASAS survey data as well as from the new LCs reported herein that maximum light during quadrature (Max I and Max II) is often not equal. As a result, Roche modeling of the TYC 2058-753-1 LCs was investigated with and without surface spots to address this asymmetry as well as a diagonally-aligned flat bottom during Min I that was observed in 2017.

Blocking contacts for N-type cadmium zinc telluride

NASA Technical Reports Server (NTRS)

Stahle, Carl M. (Inventor); Parker, Bradford H. (Inventor); Babu, Sachidananda R. (Inventor)

2012-01-01

A process for applying blocking contacts on an n-type CdZnTe specimen includes cleaning the CdZnTe specimen; etching the CdZnTe specimen; chemically surface treating the CdZnTe specimen; and depositing blocking metal on at least one of a cathode surface and an anode surface of the CdZnTe specimen.

Separation negatives from Kodak film types SO-368 and SO-242

NASA Technical Reports Server (NTRS)

Weinstein, M. S.

1972-01-01

Two master resolution friskets were produced on Kodak film types SO-368 and SO-242. These target masters consisted of 21 density steps with three-bar resolution targets at five modulation levels within each step. The target masters were contact printed onto Kodak separation negative film, type 4131, using both a contact printing frame and enlarger as one method of exposure, and a Miller-Holzwarth contact printer as the other exposing device. Red, green, and blue Wratten filters were used to filter the exposing source. Tray processing was done with DK-50 developer diluted 1:2 at a temperature of 70 F. The resolution values were read for the SO-368 and SO-242 target masters, and the red, green, and blue separation negatives.

Halogen bonds in some dihalogenated phenols: applications to crystal engineering.

PubMed

Mukherjee, Arijit; Desiraju, Gautam R

2014-01-01

3,4-Dichlorophenol (1) crystallizes in the tetragonal space group I41/a with a short axis of 3.7926 (9) Å. The structure is unique in that both type I and type II Cl⋯Cl interactions are present, these contact types being distinguished by the angle ranges of the respective C-Cl⋯Cl angles. The present study shows that these two types of contacts are utterly different. The crystal structures of 4-bromo-3-chlorophenol (2) and 3-bromo-4-chlorophenol (3) have been determined. The crystal structure of (2) is isomorphous to that of (1) with the Br atom in the 4-position participating in a type II interaction. However, the monoclinic P21/c packing of compound (3) is different; while the structure still has O-H⋯O hydrogen bonds, the tetramer O-H⋯O synthon seen in (1) and (2) is not seen. Rather than a type I Br⋯Br interaction which would have been mandated if (3) were isomorphous to (1) and (2), Br forms a Br⋯O contact wherein its electrophilic character is clearly evident. Crystal structures of the related compounds 4-chloro-3-iodophenol (4) and 3,5-dibromophenol (5) were also determined. A computational survey of the structural landscape was undertaken for (1), (2) and (3), using a crystal structure prediction protocol in space groups P21/c and I41/a with the COMPASS26 force field. While both tetragonal and monoclinic structures are energetically reasonable for all compounds, the fact that (3) takes the latter structure indicates that Br prefers type II over type I contacts. In order to differentiate further between type I and type II halogen contacts, which being chemically distinct are expected to have different distance fall-off properties, a variable-temperature crystallography study was performed on compounds (1), (2) and (4). Length variations with temperature are greater for type II contacts compared with type I. The type II Br⋯Br interaction in (2) is stronger than the corresponding type II Cl⋯Cl interaction in (1), leading to elastic bending of the former upon application of mechanical stress, which contrasts with the plastic deformation of (1). The observation of elastic deformation in (2) is noteworthy; in that it finds an explanation based on the strengths of the respective halogen bonds, it could also be taken as a good starting model for future property design. Cl/Br isostructurality is studied with the Cambridge Structural Database and it is indicated that this isostructurality is based on shape and size similarity of Cl and Br, rather than arising from any chemical resemblance.

Disease-avoidance processes and stigmatization: cues of substandard health arouse heightened discomfort with physical contact.

PubMed

Park, Justin H; van Leeuwen, Florian; Chochorelou, Ypapanti

2013-01-01

An evolutionary approach to stigmatization suggests that disease-avoidance processes contribute to some instances of social exclusion. Disease-avoidance processes are over-inclusive, targeting even non-threatening individuals who display cues of substandard health. We investigated whether such cues motivate avoidance of physical contact in particular. In Studies 1 and 2, targets with disease (e.g., leprosy) or atypical morphologies (e.g., amputated leg, obesity) were found to arouse differentially heightened discomfort with physical (versus nonphysical) contact, whereas a criminal target (stigmatized for disease-irrelevant reasons) was found to arouse elevated discomfort for both types of contact. Study 3 used a between-subjects design that eliminated the influence of extraneous factors. A diseased target was found to arouse differentially heightened discomfort with physical (versus nonphysical) contact, and to do so more strongly than any other type of target.

Au-Doped Indium Tin Oxide Ohmic Contacts to p-Type GaN

NASA Astrophysics Data System (ADS)

Guo, H.; Andagana, H. B.; Cao, X. A.

2010-05-01

Indium tin oxide (ITO) thin films doped with Au, Ni, or Pt (3.5 at.% to 10.5 at.%) were deposited on p-GaN epilayers (Mg ~4 × 1019 cm-3) using direct-current (DC) sputter codeposition. It was found that undoped ITO con- tacts to p-GaN exhibited leaky Schottky behavior, whereas the incorporation of a small amount of Au (3.5 at.% to 10.5 at.%) significantly improved their ohmic characteristics. Compared with standard Ni/ITO contacts, the Au-doped ITO contacts had a similar specific contact resistance in the low 10-2 Ω cm-2 range, but were more stable above 600°C and more transparent at blue wavelengths. These results provide support for the use of Au-doped ITO ohmic contact to p-type GaN in high-brightness blue light-emitting diodes.

Low resistance Ohmic contact to p-type crystalline silicon via nitrogen-doped copper oxide films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Xinyu, E-mail: xinyu.zhang@anu.edu.au; Wan, Yimao; Bullock, James

2016-08-01

This work explores the application of transparent nitrogen doped copper oxide (CuO{sub x}:N) films deposited by reactive sputtering to create hole-selective contacts for p-type crystalline silicon (c-Si) solar cells. It is found that CuO{sub x}:N sputtered directly onto crystalline silicon is able to form an Ohmic contact. X-ray photoelectron spectroscopy and Raman spectroscopy measurements are used to characterise the structural and physical properties of the CuO{sub x}:N films. Both the oxygen flow rate and the substrate temperature during deposition have a significant impact on the film composition, as well as on the resulting contact resistivity. After optimization, a low contactmore » resistivity of ∼10 mΩ cm{sup 2} has been established. This result offers significant advantages over conventional contact structures in terms of carrier transport and device fabrication.« less

Fast radio bursts: the observational case for a Galactic origin

NASA Astrophysics Data System (ADS)

Maoz, Dan; Loeb, Abraham; Shvartzvald, Yossi; Sitek, Monika; Engel, Michael; Kiefer, Flavien; Kiraga, Marcin; Levi, Amir; Mazeh, Tsevi; Pawlak, Michał; Rich, R. Michael; Tal-Or, Lev; Wyrzykowski, Lukasz

2015-12-01

There are by now ten published detections of fast radio bursts (FRBs) - single bright GHz-band millisecond pulses of unknown origin. Proposed explanations cover a broad range from exotic processes at cosmological distances to atmospheric and terrestrial sources. Loeb, Maoz, and Shvartzvald have previously suggested that FRB sources could be nearby flare stars, and pointed out the presence of a W-UMa-type contact binary within the beam of one out of three FRB fields that they examined. To further test the flare-star hypothesis, we use time-domain optical photometry and spectroscopy, and now find possible flare stars in additional FRB fields, with one to three such cases among all eight FRB fields studied. We evaluate the chance probabilities of these possible associations to be in the range ˜0.1 per cent to 9 per cent, depending on the input assumptions. Further, we re-analyse the probability that two FRBs recently discovered three years apart within the same radio beam are unrelated. Contrary to other claims, we conclude with 99 per cent confidence that the two events are from the same repeating source. The different dispersion measures between the two bursts then rule out a cosmological intergalactic-medium origin for the dispersion measure, but are consistent with the flare-star scenario with a varying plasma blanket between bursts. Finally, we review some theoretical objections that have been raised against a local flare-star FRB origin, and show that they are incorrect.

Pattern Laser Annealing by a Pulsed Laser

NASA Astrophysics Data System (ADS)

Komiya, Yoshio; Hoh, Koichiro; Murakami, Koichi; Takahashi, Tetsuo; Tarui, Yasuo

1981-10-01

Preliminary experiments with contact-type pattern laser annealing were made for local polycrystallization of a-Si, local evaporation of a-Si and local formation of Ni-Si alloy. These experiments showed that the mask patterns can be replicated as annealed regions with a resolution of a few microns on substrates. To overcome shortcomings due to the contact type pattern annealing, a projection type reduction pattern laser annealing system is proposed for resistless low temperature pattern forming processes.

Design rules for vertical interconnections by reverse offset printing

NASA Astrophysics Data System (ADS)

Kusaka, Yasuyuki; Kanazawa, Shusuke; Ushijima, Hirobumi

2018-03-01

Formation of vertical interconnections by reverse offset printing was investigated, particularly focusing on the transfer step, in which an ink pattern is transferred from a polydimethylsiloxane (PDMS) sheet for the step coverage of contact holes. We systematically examined the coverage of contact holes made of a tapered photoresist layer by varying the hole size, the hole depth, PDMS elasticity, PDMS thickness, printing speed, and printing indentation depth. Successful ink filling was achieved when the PDMS was softer, and the optimal PDMS thickness varied depending on the size of the contact holes. This behaviour is related to the bell-type uplift deformation of incompressible PDMS, which can be described by contact mechanics numerical simulations. Based on direct observation of PDMS/resist-hole contact behaviour, the step coverage of contact holes typically involves two steps of contact area growth: (i) the PDMS first touches the bottom of the holes and then (ii) the contact area gradually and radially widens toward the tapered sidewall. From an engineering perspective, it is pointed out that mechanical synchronisation mismatch in the roll-to-sheet type printing invokes the cracking of ink layers at the edges of contact holes. According to the above design rule, ink filling into a contact hole with thickness of 2.5 µm and radius of 10 µm was achieved. Contact chain patterns with 1386 points of vertical interconnections with the square hole size of up to 10 µm successfully demonstrated the validity of the technique presented herein.

The number of satellite cells in slow and fast fibres from human vastus lateralis muscle.

PubMed

Kadi, Fawzi; Charifi, Nadia; Henriksson, Jan

2006-07-01

The aim of this investigation was to study the distribution of satellite cells in slow (type I fibres) and fast (type II fibres) fibres from human vastus lateralis muscle. This muscle is characterised by a mixed fibre type composition and is considered as the site of choice for biopsies in research work and for clinical diagnosis. Biopsy samples were obtained from five healthy young volunteers and a total of 1,747 type I fibres and 1,760 type II fibres were assessed. Satellite cells and fibre type composition were studied on serial muscle cross-sections stained with specific monoclonal antibodies. From a total of 218 satellite cells, 116 satellite cells were found in contact with type I fibres (53.6+/-8% of the satellite cells associated to type I fibres) and 102 satellite cells in contact with type II fibres (46.4+/-8% of the satellite cells associated to type II fibres). There was no significant difference (P=0.4) between the percentages of satellite cells in contact with type I and with type II fibres. Additionally, there was no relationship between the mean number of satellite cells per fibre and the mean cross-sectional area of muscle fibres. In conclusion, our results show that there is no fibre type-specific distribution of satellite cells in a human skeletal muscle with mixed fibre type composition.

Ocular surface and tear film status among contact lens wearers and non-wearers who use VDT at work: comparing three different lens types.

PubMed

Tauste, Ana; Ronda, Elena; Baste, Valborg; Bråtveit, Magne; Moen, Bente E; Seguí Crespo, María-Del-Mar

2018-04-01

To analyze differences in the ocular surface appearance and tear film status of contact lens wearers and non-wearers in a group of visual display terminals (VDT) workers and additionally to assess differences between lens materials. Cross-sectional study of 236 office workers, of whom 92 were contact lens wearers. Workers provided information on their contact lenses (conventional hydrogel, silicone hydrogel or rigid gas permeable lenses) and exposure to VDT at work. Ocular surface and tear film status were determined by the presence of bulbar, limbal and lid redness, lid roughness and corneal staining type, and by Schirmer's and tear break-up time tests (TBUT). A generalized linear model was used to calculate the crude (cRR) and age- and sex-adjusted (aRR) relative risk to measure the association between ocular surface and tear film abnormalities and contact lens use and type. The aRR of ocular surface abnormalities was higher in contact lens wearers compared to non-wearers: bulbar redness (aRR 1.69; 95% CI 1.25-2.30), limbal redness (aRR 2.87; 1.88-4.37), lid redness (aRR 2.53; 1.35-4.73) and lid roughness (aRR 7.03; 1.31-37.82). VDT exposure > 4 h/day increased wearers' risk of limbal and lid redness. Conventional hydrogel wearers had the highest risk of ocular surface abnormalities, followed by silicone hydrogel wearers. Both contact and non-contact lens wearers had a high prevalence of altered TBUT (77.3 and 75.7% respectively) and Schirmer (51.8 and 41.3%). Regular contact lens use during VDT exposure at work increases risk of bulbar, limbal and lid redness, and lid roughness, especially in soft contact lens wearers. The high prevalence of altered TBUT and Schirmer's results in all participants suggests that VDT use greatly affects tear film characteristics.

The impact of nanocontact on nanowire based nanoelectronics.

PubMed

Lin, Yen-Fu; Jian, Wen-Bin

2008-10-01

Nanowire-based nanoelectronic devices will be innovative electronic building blocks from bottom up. The reduced nanocontact area of nanowire devices magnifies the contribution of contact electrical properties. Although a lot of two-contact-based ZnO nanoelectronics have been demonstrated, the electrical properties bringing either from the nanocontacts or from the nanowires have not been considered yet. High quality ZnO nanowires with a small deviation and an average diameter of 38 nm were synthesized to fabricate more than thirty nanowire devices. According to temperature behaviors of current-voltage curves and resistances, the devices could be grouped into three types. Type I devices expose thermally activated transport in ZnO nanowires and they could be considered as two Ohmic nanocontacts of the Ti electrode contacting directly on the nanowire. For those nanowire devices having a high resistance at room temperatures, they can be fitted accurately with the thermionic-emission theory and classified into type II and III devices according to their rectifying and symmetrical current-voltage behaviors. The type II device has only one deteriorated nanocontact and the other one Ohmic contact on single ZnO nanowire. An insulating oxide layer with thickness less than 20 nm should be introduced to describe electron hopping in the nanocontacts, so as to signalize one- and high-dimensional hopping conduction in type II and III devices.

American Contact Dermatitis Society Contact Allergy Management Program: An Epidemiologic Tool to Quantify Ingredient Usage.

PubMed

Scheman, Andrew; Severson, David

2016-01-01

The usage prevalence of ingredients in topical products is important to dermatologists and industry. To determine the prevalence of methylisothiazolinone (MI) in various types of consumer products The Contact Allergy Management Program (CAMP) database was mapped and sorted in spreadsheet format to determine the prevalence of MI in various types of consumer products. Methylisothiazolinone was found in 13.2% of 4660 total products in CAMP. High usage of MI was seen in dishwashing products (64%), shampoos (53%), bathroom/kitchen/all-purpose cleaners (47%), hair conditioners (45%), hair dyes (43%), laundry additives/fresheners/softeners (30%), soaps/cleansers (29%), and surface cleaners/disinfectants (27%). Of the products containing MI, MI alone (without methylchloroisothiazolinone) was most common in makeup products (100%), cleaning/dish/laundry products (>99%), moisturizers (82%), shaving products (78%), sunscreens (71%), and antiaging products (67%). The American Contact Dermatitis Society's CAMP is a valuable tool to collect epidemiologic data on the incidence of specific ingredient usage in various types of topical products.

Competitive Sport Involvement and Substance Use among Adolescents: A Nationwide Study

PubMed Central

Veliz, Philip Todd; Boyd, Carol J.; McCabe, Sean Esteban

2015-01-01

Background The empirical research examining the impact of sports participation on alcohol and other drug use has produced mixed results. Part of this problem may be the result of how different types of sports participation create different experiences that shape certain types of behaviors that either facilitate or deter substance use. Objectives We examined the association between different types of competitive sports participation and substance use among a nationally representative sample of adolescents. Methods Two recent cross-sections from the Monitoring the Future were merged to capture a large subsection of adolescents who participate in either high-contact sports (football, wrestling, hockey and lacrosse), semi-contact sports (baseball, basketball, field hockey and soccer), and non-contact sports (cross-country, gymnastics, swimming, tennis, track, and volleyball). Results Multivariate analyses revealed that adolescents who participated in high-contact sports had higher odds of using substances during the past 30 days and initiating substance use at early ages. Further, adolescents who participated in non-contact sports had lower odds to indicate smoking cigarettes and marijuana during the past 30 days. Conclusions Parents, educators, and policy makers need to consider that some sporting contexts may be a catalyst to engage in risky behaviors like substance use. PMID:25290659

Occupational protein contact dermatitis in food handlers.

PubMed

Hjorth, N; Roed-Petersen, J

1976-02-01

The preparation of food in restaurant kitchens carries a high risk of occupational dermatoses. Analysis of 33 cases revealed four different etiological types. Simple irritant dermatitis was rare (2 cases), plain contact dermatitis was more common (6 cases). Fifteen patients had relevant patch tests and scratch tests; ten had positive scratch tests only to explain the cause of their dermatitis. The last type was termed protein contact dermatitis. The major type IV allergens incriminated were metals, onion and garlic. The major proteinaceous allergens indicated by history and test results were fish and shell-fish. Open patch tests with the incriminated foods may cause erythema or oedema on normal skin after 20 minutes. Previously eczematous, now normal looking, skin often responds with a crop of dyshidrotic vesicles preceded by erythema and itching 30 minutes after the application of an open test. Examination for specific IgE is not always positive in such cases. Inhalant allergy was rare. The results indicate that food handlers are sensitized by the protein they touch, and then react to later contact with the proteins. Protein contact dermatitis is similarly common among veterinary surgeons, while the importance in other occupational groups remains to be studied.

Use of separate ZnTe interface layers to form ohmic contacts to p-CdTe films

DOEpatents

Gessert, T.A.

1999-06-01

A method of is disclosed improving electrical contact to a thin film of a p-type tellurium-containing II-VI semiconductor comprising: depositing a first undoped layer of ZnTe on a thin film of p-type tellurium containing II-VI semiconductor with material properties selected to limit the formation of potential barriers at the interface between the p-CdTe and the undoped layer, to a thickness sufficient to control diffusion of the metallic-doped ZnTe into the p-type tellurium-containing II-VI semiconductor, but thin enough to minimize affects of series resistance; depositing a second heavy doped p-type ZnTe layer to the first layer using an appropriate dopant; and depositing an appropriate metal onto the outer-most surface of the doped ZnTe layer for connecting an external electrical conductor to an ohmic contact. 11 figs.

Use of separate ZnTe interface layers to form OHMIC contacts to p-CdTe films

DOEpatents

Gessert, Timothy A.

1999-01-01

A method of improving electrical contact to a thin film of a p-type tellurium-containing II-VI semiconductor comprising: depositing a first undoped layer of ZnTe on a thin film of p-type tellurium containing II-VI semiconductor with material properties selected to limit the formation of potential barriers at the interface between the p-CdTe and the undoped layer, to a thickness sufficient to control diffusion of the metallic-doped ZnTe into the p-type tellurim-containing II-VI semiconductor, but thin enough to minimize affects of series resistance; depositing a second heavy doped p-type ZnTe layer to the first layer using an appropriate dopant; and depositing an appropriate metal onto the outer-most surface of the doped ZnTe layer for connecting an external electrical conductor to an ohmic contact.

Contact dermatitis following sustained exposure to pecans (Carya illinoensis): a case report.

PubMed

Joyce, Kathleen M; Boyd, Jason; Viernes, Jay L

2006-04-01

Type I hypersensitivity reactions following ingestion of peanuts and tree nuts are well characterized. Cutaneous hypersensitivity reactions are less well characterized, yet they remain the second most common reaction pattern to contact with or ingestion of such nuts. We present a case of a patient who experienced an acute vesicular cutaneous reaction after prolonged contact with pecans. This case illustrates the salient features of contact dermatitis and serves as a reminder that contact with allergenic foods can lead to hypersensitivity reactions.

Review on prevention of bacterial adhesion on contact lens using plasma treatment

NASA Astrophysics Data System (ADS)

Ramli, N. A. H.; Zaaba, S. K.; Mustaffa, M. T.; Zakaria, A.; Shahriman A., B.

2017-03-01

Many researches had been conducted to enhance the properties of contact lens. Most of the research conducted discussed on the factors that affect the adhesion process to contact lenses, rate of contact lens contamination, and type of microbe that adhere on the contact lens surface and contact lens casing. Studies on the proposed strategies or technology that can be used to slower down the formation of bacteria on contact lens are being explored. New technologies or strategies to prevent or slow down the adhesion of bacteria on contact lens have become a priority in this area. This review paper covers two main aspects, namely factor that affect the bacteria adhesion on contact lens and also the introduction of plasma treatment as a potential method for contact lens treatment.

Occupational Dermatoses by Type of Work in Greece

PubMed Central

Zorba, Eleni; Karpouzis, Antony; Zorbas, Alexandros; Bazas, Theodore; Zorbas, Sam; Alexopoulos, Elias; Zorbas, Ilias; Kouskoukis, Konstantinos; Konstandinidis, Theodoros

2013-01-01

Background To elucidate the relationship between seven occupational dermatoses (ODs) and 20 types of work in Greece. Methods This was a prevalence epidemiologic study of certain ODs among 4,000 workers employed in 20 types of enterprise, in 104 companies, in 2006–2012, using data from company medical records, questionnaires, occupational medical, and special examinations. The χ2 test was applied to reveal statistically significant relationships between types of enterprises and occurrence of ODs. Results A high percentage (39.9%) of employees included in the study population suffered from ODs. The highest prevalence rates were noted among hairdressers (of contact dermatitis: 30%), cooks (of contact dermatitis: 29.5%), bitumen workers (of acne: 23.5%), car industry workers (of mechanical injury: 15%), construction workers (of contact urticaria: 29.5%), industrial cleaning workers (of chemical burns: 13%), and farmers (of malignant tumors: 5.5%). We observed several statistical significant correlations between ODs (acute and chronic contact dermatitis, urticaria, mechanical injury, acne, burns, skin cancer) and certain types of enterprises. There was no statistically significant correlation between gender and prevalence of ODs, except for dermatoses caused by mechanical injuries afflicting mainly men [χ2 (1) = 13.40, p < 0.001] and for chronic contact dermatitis [χ2 (1) = 5.53, p = 0.019] afflicting mainly women. Conclusion Prevalence of ODs is high in Greece, contrary to all official reports by the Greek National Institute of Health. There is a need to introduce a nationwide voluntary surveillance system for reporting ODs and to enhance skin protection measures at work. PMID:24106644

Occupational dermatoses by type of work in Greece.

PubMed

Zorba, Eleni; Karpouzis, Antony; Zorbas, Alexandros; Bazas, Theodore; Zorbas, Sam; Alexopoulos, Elias; Zorbas, Ilias; Kouskoukis, Konstantinos; Konstandinidis, Theodoros

2013-09-01

To elucidate the relationship between seven occupational dermatoses (ODs) and 20 types of work in Greece. This was a prevalence epidemiologic study of certain ODs among 4,000 workers employed in 20 types of enterprise, in 104 companies, in 2006-2012, using data from company medical records, questionnaires, occupational medical, and special examinations. The χ(2) test was applied to reveal statistically significant relationships between types of enterprises and occurrence of ODs. A high percentage (39.9%) of employees included in the study population suffered from ODs. The highest prevalence rates were noted among hairdressers (of contact dermatitis: 30%), cooks (of contact dermatitis: 29.5%), bitumen workers (of acne: 23.5%), car industry workers (of mechanical injury: 15%), construction workers (of contact urticaria: 29.5%), industrial cleaning workers (of chemical burns: 13%), and farmers (of malignant tumors: 5.5%). We observed several statistical significant correlations between ODs (acute and chronic contact dermatitis, urticaria, mechanical injury, acne, burns, skin cancer) and certain types of enterprises. There was no statistically significant correlation between gender and prevalence of ODs, except for dermatoses caused by mechanical injuries afflicting mainly men [χ(2) (1) = 13.40, p < 0.001] and for chronic contact dermatitis [χ(2) (1) = 5.53, p = 0.019] afflicting mainly women. Prevalence of ODs is high in Greece, contrary to all official reports by the Greek National Institute of Health. There is a need to introduce a nationwide voluntary surveillance system for reporting ODs and to enhance skin protection measures at work.

Allergic Contact Dermatitis (Type IV Hypersensitivity) and Type I Hypersensitivity Following Aromatherapy with Ayurvedic Oils (Dhanwantharam Thailam, Eladi Coconut Oil) Presenting as Generalized Erythema and Pruritus with Flexural Eczema

PubMed Central

Lakshmi, Chembolli

2014-01-01

Herbal and Ayurvedic medications, believed to be “mild” and “natural” are usually sought as the first line of treatment before resorting to “stronger” allopathic medication. There are very few reports of adverse reactions to either topical and/or systemic Ayurvedic medications. Massage aromatherapy with ayurvedic oils plays an important role in alleviation of pain, but may cause allergic contact dermatitis. This is the second case report of allergic contact dermatitis to ayurvedic oil. PMID:24891661

Investigation into the effects of surface stripping ZnO nanosheets.

PubMed

Barnett, Chris J; Jackson, Georgina; Jones, Daniel R; Lewis, Aled R; Welsby, Kathryn; Evans, Jon E; McGettrick, James D; Watson, Trystan; Maffeis, Thierry G G; Dunstan, Peter R; Barron, Andrew R; Cobley, Richard J

2018-04-20

ZnO nanosheets are polycrystalline nanostructures that are used in devices including solar cells and gas sensors. However, for efficient and reproducible device operation and contact behaviour the conductivity characteristics must be controlled and surface contaminants removed. Here we use low doses of argon bombardment to remove surface contamination and make reproducible lower resistance contacts. Higher doses strip the surface of the nanosheets altering the contact type from near-ohmic to rectifying by removing the donor-type defects, which photoluminescence shows to be concentrated in the near-surface. Controlled doses of argon treatments allow nanosheets to be customised for device formation.

Investigation into the effects of surface stripping ZnO nanosheets

NASA Astrophysics Data System (ADS)

Barnett, Chris J.; Jackson, Georgina; Jones, Daniel R.; Lewis, Aled R.; Welsby, Kathryn; Evans, Jon E.; McGettrick, James D.; Watson, Trystan; Maffeis, Thierry G. G.; Dunstan, Peter R.; Barron, Andrew R.; Cobley, Richard J.

2018-04-01

ZnO nanosheets are polycrystalline nanostructures that are used in devices including solar cells and gas sensors. However, for efficient and reproducible device operation and contact behaviour the conductivity characteristics must be controlled and surface contaminants removed. Here we use low doses of argon bombardment to remove surface contamination and make reproducible lower resistance contacts. Higher doses strip the surface of the nanosheets altering the contact type from near-ohmic to rectifying by removing the donor-type defects, which photoluminescence shows to be concentrated in the near-surface. Controlled doses of argon treatments allow nanosheets to be customised for device formation.

The long-term experiences of surrogates: relationships and contact with surrogacy families in genetic and gestational surrogacy arrangements.

PubMed

Imrie, Susan; Jadva, Vasanti

2014-10-01

This study examined the contact arrangements and relationships between surrogates and surrogacy families and whether these outcomes differed according to the type of surrogacy undertaken. Surrogates' motivations for carrying out multiple surrogacy arrangements were also examined, and surrogates' psychological health was assessed. Semi-structured interviews were administered to 34 women who had given birth to a child conceived through surrogacy approximately 7 years prior to interview. Some surrogates had carried out multiple surrogacy arrangements, and data were collected on the frequency, type of contact, and surrogate's feelings about the level of contact in each surrogacy arrangement, the surrogate's relationship with each child and parent, and her experience of, and motivation for, each surrogacy. Questionnaire measures of psychological health were administered. Surrogates had completed a total of 102 surrogacy arrangements and remained in contact with the majority of families, and reported positive relationships in most cases. Surrogates were happy with their level of contact in the majority of arrangements and most were viewed as positive experiences. Few differences were found according to surrogacy type. The primary motivation given for multiple surrogacy arrangements was to help couples have a sibling for an existing child. Most surrogates showed no psychological health problems at the time of data collection. Copyright © 2014 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

Localization of acetylcholine receptors and synaptic ultrastructure at nerve-muscle contacts in culture: dependence on nerve type

PubMed Central

Cohen, MW; Weldon, PR

1980-01-01

In cultures of xenopus myotomal muscle cells and spinal cord (SC) some of the nerve-muscle contacts exhibit a high density of acetylcholine receptors (AchRs [Anderson et al., 1977, J. Physiol. (Lond.). 268:731- 756,757-773]) and synaptic ultrastructure (Weldon and Cohen, 1979, J. Neurocytol. 8:239-259). We have examined whether similarly specialized contacts are established when the muscle cells are cultured with explants of xenopus dorsal root ganglia (DRG) or sympathetic ganglia (SG). The outgrowth from the ganglionic explants contained neuronal and non- neuronal cell processes. Although both types of processes approached within 100 A of muscle cells, synaptic ultrastructure was rarely observed at these contacts. Because patches of postsynaptic ultrastructure also develop on noncontacted muscle cells, the very few examples of contacts with such specializations probably occurred by chance. AChRs were stained with fluroscent α-bungarotoxin. More than 70 percent of the SC-contacted muscle cells exhibited a high receptor density along the path of contact. The corresponding values for DRG- and SG- contacted muscle cells were 10 and 6 percent. Similar values were obtained when the ganlionic and SC explants were cultured together in the same chamber. The few examples of high receptor density at ganglionic-muscle contacts resembled the characteristic receptor patches of noncontacted muscle cells rather than the narrow bands of high receptor density seen at SC-muscle contacts. In addition, more than 90 percent of these ganglionic- contacted muscle cells had receptor patches elsewhere, compared to less than 40 percent for the SC-contacted muscle cells. These findings indicate that the SC neurites possess a specific property which is important for the establishment of synaptically specialized contacts with muscle and that this property is lacking in the DRG and SG neurites. PMID:7400212

Asymmetries in the individual distinctiveness and maternal recognition of infant contact calls and distress screams in baboons

PubMed Central

Rendall, Drew; Notman, Hugh; Owren, Michael J.

2009-01-01

A key component of nonhuman primate vocal communication is the production and recognition of clear cues to social identity that function in the management of these species’ individualistic social relationships. However, it remains unclear how ubiquitous such identity cues are across call types and age-sex classes and what the underlying vocal production mechanisms responsible might be. This study focused on two structurally distinct call types produced by infant baboons in contexts that place a similar functional premium on communicating clear cues to caller identity: (1) contact calls produced when physically separated from, and attempting to relocate, mothers and (2) distress screams produced when aggressively attacked by other group members. Acoustic analyses and field experiments were conducted to examine individual differentiation in single vocalizations of each type and to test mothers’ ability to recognize infant calls. Both call types showed statistically significant individual differentiation, but the magnitude of the differentiation was substantially higher in contact calls. Mothers readily discriminated own-offspring contact calls from those of familiar but unrelated infants, but did not do so when it came to distress screams. Several possible explanations for these asymmetries in call differentiation and recognition are considered. PMID:19275336

ZnO Schottky barriers and Ohmic contacts

NASA Astrophysics Data System (ADS)

Brillson, Leonard J.; Lu, Yicheng

2011-06-01

ZnO has emerged as a promising candidate for optoelectronic and microelectronic applications, whose development requires greater understanding and control of their electronic contacts. The rapid pace of ZnO research over the past decade has yielded considerable new information on the nature of ZnO interfaces with metals. Work on ZnO contacts over the past decade has now been carried out on high quality material, nearly free from complicating factors such as impurities, morphological and native point defects. Based on the high quality bulk and thin film crystals now available, ZnO exhibits a range of systematic interface electronic structure that can be understood at the atomic scale. Here we provide a comprehensive review of Schottky barrier and ohmic contacts including work extending over the past half century. For Schottky barriers, these results span the nature of ZnO surface charge transfer, the roles of surface cleaning, crystal quality, chemical interactions, and defect formation. For ohmic contacts, these studies encompass the nature of metal-specific interactions, the role of annealing, multilayered contacts, alloyed contacts, metallization schemes for state-of-the-art contacts, and their application to n-type versus p-type ZnO. Both ZnO Schottky barriers and ohmic contacts show a wide range of phenomena and electronic behavior, which can all be directly tied to chemical and structural changes on an atomic scale.

Immersed finger-type indium tin oxide ohmic contacts on p-GaN photoelectrodes for photoelectrochemical hydrogen generation.

PubMed

Liu, Shu-Yen; Sheu, J K; Lee, M L; Lin, Yu-Chuan; Tu, S J; Huang, F W; Lai, W C

2012-03-12

In this study, we demonstrated photoelectrochemical (PEC) hydrogen generation using p-GaN photoelectrodes associated with immersed finger-type indium tin oxide (IF-ITO) ohmic contacts. The IF-ITO/p-GaN photoelectrode scheme exhibits higher photocurrent and gas generation rate compared with p-GaN photoelectrodes without IF-ITO ohmic contacts. In addition, the critical external bias for detectable hydrogen generation can be effectively reduced by the use of IF-ITO ohmic contacts. This finding can be attributed to the greatly uniform distribution of the IF-ITO/p-GaN photoelectrode applied fields over the whole working area. As a result, the collection efficiency of photo-generated holes by electrode contacts is higher than that of p-GaN photoelectrodes without IF-ITO contacts. Microscopy revealed a tiny change on the p-GaN surfaces before and after hydrogen generation. In contrast, photoelectrodes composed of n-GaN have a short lifetime due to n-GaN corrosion during hydrogen generation. Findings of this study indicate that the ITO finger contacts on p-GaN layer is a potential candidate as photoelectrodes for PEC hydrogen generation.

Interdigitated back contact solar cells with polycrystalline silicon on oxide passivating contacts for both polarities

NASA Astrophysics Data System (ADS)

Haase, Felix; Kiefer, Fabian; Schäfer, Sören; Kruse, Christian; Krügener, Jan; Brendel, Rolf; Peibst, Robby

2017-08-01

We demonstrate an independently confirmed 25.0%-efficient interdigitated back contact silicon solar cell with passivating polycrystalline silicon (poly-Si) on oxide (POLO) contacts that enable a high open circuit voltage of 723 mV. We use n-type POLO contacts with a measured saturation current density of J 0n = 4 fA cm-2 and p-type POLO contacts with J 0p = 10 fA cm-2. The textured front side and the gaps between the POLO contacts on the rear are passivated by aluminum oxide (AlO x ) with J 0AlO x = 6 fA cm-2 as measured after deposition. We analyze the recombination characteristics of our solar cells at different process steps using spatially resolved injection-dependent carrier lifetimes measured by infrared lifetime mapping. The implied pseudo-efficiency of the unmasked cell, i.e., cell and perimeter region are illuminated during measurement, is 26.2% before contact opening, 26.0% after contact opening and 25.7% for the finished cell. This reduction is due to an increase in the saturation current density of the AlO x passivation during chemical etching of the contact openings and of the rear side metallization. The difference between the implied pseudo-efficiency and the actual efficiency of 25.0% as determined by designated-area light current-voltage (I-V) measurements is due to series resistance and diffusion of excess carriers into the non-illuminated perimeter region.

Busca de estruturas em grandes escalas em altos redshifts

NASA Astrophysics Data System (ADS)

Boris, N. V.; Sodré, L., Jr.; Cypriano, E.

2003-08-01

A busca por estruturas em grandes escalas (aglomerados de galáxias, por exemplo) é um ativo tópico de pesquisas hoje em dia, pois a detecção de um único aglomerado em altos redshifts pode por vínculos fortes sobre os modelos cosmológicos. Neste projeto estamos fazendo uma busca de estruturas distantes em campos contendo pares de quasares próximos entre si em z Â3 0.9. Os pares de quasares foram extraídos do catálogo de Véron-Cetty & Véron (2001) e estão sendo observados com os telescópios: 2,2m da University of Hawaii (UH), 2,5m do Observatório de Las Campanas e com o GEMINI. Apresentamos aqui a análise preliminar de um par de quasares observado nos filtros i'(7800 Å) e z'(9500 Å) com o GEMINI. A cor (i'-z') mostrou-se útil para detectar objetos "early-type" em redshifts menores que 1.1. No estudo do par 131046+0006/J131055+0008, com redshift ~ 0.9, o uso deste método possibilitou a detecção de sete objetos candidatos a galáxias "early-type". Num mapa da distribuição projetada dos objetos para 22 < i' < 25 observou-se que estas galáxias estão localizadas próximas a um dos quasares e há indícios de que estejam aglomeradas dentro de um área de ~ 6 arcmin2. Se esse for o caso, estes objetos seriam membros de uma estrutura em grande escala. Um outro argumento em favor dessa hipótese é que eles obedecem uma relação do tipo Kormendy (raio equivalente X brilho superficial dentro desse raio), como a apresentada pelas galáxias elípticas em z = 0.

Fermi level de-pinning of aluminium contacts to n-type germanium using thin atomic layer deposited layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gajula, D. R., E-mail: dgajula01@qub.ac.uk; Baine, P.; Armstrong, B. M.

Fermi-level pinning of aluminium on n-type germanium (n-Ge) was reduced by insertion of a thin interfacial dielectric by atomic layer deposition. The barrier height for aluminium contacts on n-Ge was reduced from 0.7 eV to a value of 0.28 eV for a thin Al{sub 2}O{sub 3} interfacial layer (∼2.8 nm). For diodes with an Al{sub 2}O{sub 3} interfacial layer, the contact resistance started to increase for layer thicknesses above 2.8 nm. For diodes with a HfO{sub 2} interfacial layer, the barrier height was also reduced but the contact resistance increased dramatically for layer thicknesses above 1.5 nm.

Front contact solar cell with formed electrically conducting layers on the front side and backside

DOEpatents

Cousins, Peter John

2012-06-26

A bipolar solar cell includes a backside junction formed by a silicon substrate and a first doped layer of a first dopant type on the backside of the solar cell. A second doped layer of a second dopant type makes an electrical connection to the substrate from the front side of the solar cell. A first metal contact of a first electrical polarity electrically connects to the first doped layer on the backside of the solar cell, and a second metal contact of a second electrical polarity electrically connects to the second doped layer on the front side of the solar cell. An external electrical circuit may be electrically connected to the first and second metal contacts to be powered by the solar cell.

Family Contact and Recidivism: A Longitudinal Study of Adjudicated Delinquents in Residential Care

ERIC Educational Resources Information Center

Ryan, Joseph P.; Yang, Huilan

2005-01-01

Families are critical to understanding and interrupting patterns of delinquent and criminal behavior. The objective of this study was to determine whether specific types of contact with family members are associated with a reduced risk of recidivism after a long-term residential program for juvenile delinquents. Family contact reports were…

[Type IV contact allergies in the food processing industry: an update].

PubMed

Bauer, A; Schubert, S; Geier, J; Mahler, V

2018-06-01

The food sector is one of the high-risk areas for occupational irritative and allergic contact eczema. The present work provides an overview of the main allergens as well as sensitization frequencies and risk in various food industry occupations. The literature on type IV sensitization in the food sector is summarized. The relative risk of developing a work-related eczema in food processing is increased by more than 3 times. The comparison group was calculated on the basis of the proportion of documented cases in the IVDK (Informationsverbund Dermatologischer Kliniken) network per 100,000 working persons in relation to the average of the years 2005 and 2010. For this purpose, the average risk of all patients was set as reference to 1. Bakers, pastry chefs, cooks and meat and fish processors are mainly affected. In addition to irritant contact eczema, allergic contact eczema and protein contact dermatitis often occur. Leading haptens (main allergens) are rubber ingredients, but also disinfectants and compositae. Only a few contact allergens are responsible for the majority of job-relevant sensitizations in the food industry.

Novel contact hole reticle design for enhanced lithography process window in IC manufacturing

NASA Astrophysics Data System (ADS)

Chang, Chung-Hsing

2005-01-01

For 90nm node generation, 65nm, and beyond, dark field mask types such as contact-hole, via, and trench patterns that all are very challenging to print with satisfactory process windows for day-to-day lithography manufacturing. Resolution enhancement technology (RET) masks together with ArF high numerical aperture (NA) scanners have been recognized as the inevitable choice of method for 65nm node manufacturing. Among RET mask types, the alternating phase shifting mask (AltPSM) is one of the well-known strong enhancement techniques. However AltPSM can have a very strong optical proximity effect that comes with the use of small on-axis illumination sigma setting. For very dense contact features, it may be possible for AltPSM to overcome the phase conflict by limiting the mask design rules. But it is not feasible to resolve the inherent phase conflict for the semi-dense, semi-isolated and isolated contact areas. Hence the adoption of this strong enhancement technique for dark filed mask types in today"s IC manufacturing has been very limited. In this paper, we present a novel yet a very powerful design method to achieve contact and via masks printing for 90nm, 65nm, and beyond. We name our new mask design as: Novel Improved Contact-hole pattern Exposure PSM (NICE PSM) with off-axis illumination, such as QUASAR. This RET masks design can enhance the process window of isolated, semi-isolated contact hole and via hole patterns. The main concepts of NICE PSM with QUASAR off-axis illumination are analogous to the Super-FLEX pupil filter technology.

Novel contact hole reticle design for enhanced lithography process window in IC manufacturing

NASA Astrophysics Data System (ADS)

Chang, Chung-Hsing

2004-10-01

For 90nm node generation, 65nm, and beyond, dark field mask types such as contact-hole, via, and trench patterns that all are very challenging to print with satisfactory process windows for day-to-day lithography manufacturing. Resolution enhancement technology (RET) masks together with ArF high numerical aperture (NA) scanners have been recognized as the inevitable choice of method for 65nm node manufacturing. Among RET mask types, the alternating phase shifting mask (AltPSM) is one of the well-known strong enhancement techniques. However, AltPSM can have a very strong optical proximity effect that comes with the use of small on-axis illumination sigma setting. For very dense contact features, it may be possible for AltPSM to overcome the phase conflict by limiting the mask design rules. But it is not feasible to resolve the inherent phase conflict for the semi-dense, semi-isolated and isolated contact areas. Hence the adoption of this strong enhancement technique for dark filed mask types in today"s IC manufacturing has been very limited. In this paper, we report a novel yet a very powerful design method to achieve contact and via masks printing for 90nm, 65nm, and beyond. We name our new mask design as: Novel Improved Contact-hole pattern Exposure PSM (NICE PSM) with off-axis illumination, such as QUASAR. This RET masks design can enhance the process window of isolated, semi-isolated contact hole and via hole patterns. The main concepts of NICE PSM with QUASAR off-axis illumination are analogous to the Super-FLEX pupil filter technology.

Descriptive analysis of the type and design of contact lenses fitted according to keratoconus severity and morphology.

PubMed

Lunardi, Letícia Helena; Arroyo, Danielle; Andrade Sobrinho, Marcelo Vicente de; Lipener, César; Rosa, Juliana Maria da Silva

2016-04-01

Keratoconus is characterized by bilateral asymmetrical corneal ectasia that leads to inferior stromal thinning and corneal protrusion. There is currently a lack of consensus regarding the most efficacious method for fitting contact lenses in patients with keratoconus, given the various topographical patterns and evolution grades observed in affected populations. The purpose of the present study was to evaluate the association between keratoconus evolution grade and topography pattern and the type and design of fitted contact lens. We performed a retrospective analysis of contact lenses fitted in a total of 185 patients with keratoconus (325 eyes). Keratoconus was classified as either grade I, II, III, or IV based on keratometry and cone morphology (nipple, oval, globus, or indeterminate) results. A total of 325 eyes were evaluated in the present study. Of the 62 eyes classified as grade I, 66.1% were fitted with monocurve contact lenses. Of the 162 eyes classified as grade I and II, 51%, 30%, and 19% were fitted with adapted monocurve rigid gas-permeable contact lenses (RGPCL), bicurve lenses, and others lens types, respectively. Bicurve lenses were fitted in 52.1% and 62.2% of eyes classified as grade III and IV, respectively. Of the eyes classified as grade III and IV, monocurve and bicurve RGPCL were fitted in 26% and 55%, respectively. In eyes with oval keratoconus, 45%, 35%, and 20% were fitted with monocurve lenses, bicurve lenses, and other lens types, respectively. In eyes with round cones (nipple morphology), 55%, 30%, and 15% were fitted with bicurve lenses, monocurve lenses, and other lens types, respectively. Monocurve RGPCL were most frequently fitted in patients with mild to moderate keratoconus and oval cones morphology, while bicurve lenses were more frequently fitted in patients with severe and advanced keratoconus. This was probably because bicurve lenses are more appropriate for round cones due to increased corneal asphericity.

Rashes

MedlinePlus

... is called dermatitis, meaning inflammation of the skin. Contact dermatitis is caused by things your skin touches, such ... sumac, as well as for other types of contact dermatitis. Hydrocortisone cream (1%) is available without a prescription ...

SAM Technical Contacts

EPA Pesticide Factsheets

These technical contacts are available to help with questions regarding method deviations, modifications, sample problems or interferences, quality control requirements, the use of alternative methods, or the need to address analytes or sample types.

Influence of the transition region between p- and n-type polycrystalline silicon passivating contacts on the performance of interdigitated back contact silicon solar cells

NASA Astrophysics Data System (ADS)

Reichel, Christian; Müller, Ralph; Feldmann, Frank; Richter, Armin; Hermle, Martin; Glunz, Stefan W.

2017-11-01

Passivating contacts based on thin tunneling oxides (SiOx) and n- and p-type semi-crystalline or polycrystalline silicon (poly-Si) enable high passivation quality and low contact resistivity, but the integration of these p+/n emitter and n+/n back surface field junctions into interdigitated back contact silicon solar cells poses a challenge due to high recombination at the transition region from p-type to n-type poly-Si. Here, the transition region was created in different configurations—(a) p+ and n+ poly-Si regions are in direct contact with each other ("pn-junction"), using a local overcompensation (counterdoping) as a self-aligning process, (b) undoped (intrinsic) poly-Si remains between the p+ and n+ poly-Si regions ("pin-junction"), and (c) etched trenches separate the p+ and n+ poly-Si regions ("trench")—in order to investigate the recombination characteristics and the reverse breakdown behavior of these solar cells. Illumination- and injection-dependent quasi-steady state photoluminescence (suns-PL) and open-circuit voltage (suns-Voc) measurements revealed that non-ideal recombination in the space charge regions with high local ideality factors as well as recombination in shunted regions strongly limited the performance of solar cells without a trench. In contrast, solar cells with a trench allowed for open-circuit voltage (Voc) of 720 mV, fill factor of 79.6%, short-circuit current (Jsc) of 41.3 mA/cm2, and a conversion efficiencies (η) of 23.7%, showing that a lowly conducting and highly passivating intermediate layer between the p+ and n+ poly-Si regions is mandatory. Independent of the configuration, no hysteresis was observed upon multiple stresses in reverse direction, indicating a controlled and homogeneously distributed breakdown, but with different breakdown characteristics.

Contact angle hysteresis on doubly periodic smooth rough surfaces in Wenzel's regime: The role of the contact line depinning mechanism

NASA Astrophysics Data System (ADS)

Iliev, Stanimir; Pesheva, Nina; Iliev, Pavel

2018-04-01

We report here on the contact angle hysteresis, appearing when a liquid meniscus is in contact with doubly sinusoidal wavelike patterned surfaces in Wenzel's wetting regime. Using the full capillary model we obtain numerically the contact angle hysteresis as a function of the surface roughness factor and the equilibrium contact angle for a block case and a kink case contact line depinning mechanism. We find that the dependencies of the contact angle hysteresis on the surface roughness factor are different for the different contact line depinning mechanisms. These dependencies are different also for the two types of rough surfaces we studied. The relations between advancing, receding, and equilibrium contact angles are investigated. A comparison with the existing asymptotical, numerical, and experimental results is carried out.

Contact angle hysteresis on doubly periodic smooth rough surfaces in Wenzel's regime: The role of the contact line depinning mechanism.

PubMed

Iliev, Stanimir; Pesheva, Nina; Iliev, Pavel

2018-04-01

We report here on the contact angle hysteresis, appearing when a liquid meniscus is in contact with doubly sinusoidal wavelike patterned surfaces in Wenzel's wetting regime. Using the full capillary model we obtain numerically the contact angle hysteresis as a function of the surface roughness factor and the equilibrium contact angle for a block case and a kink case contact line depinning mechanism. We find that the dependencies of the contact angle hysteresis on the surface roughness factor are different for the different contact line depinning mechanisms. These dependencies are different also for the two types of rough surfaces we studied. The relations between advancing, receding, and equilibrium contact angles are investigated. A comparison with the existing asymptotical, numerical, and experimental results is carried out.

The (in)stability of 21st century orthopedic patient contact information and its implications on clinical research: a cross-sectional study

PubMed Central

London, Daniel A; Stepan, Jeffrey G; Goldfarb, Charles A; Boyer, Martin I; Calfee, Ryan P

2016-01-01

Background In clinical research, minimizing patients lost to follow-up is essential for data validity. Researchers can employ better methodology to prevent patient loss. We examined how orthopedic surgery patients’ contact information changes over time to optimize data collection for long-term outcomes research. Methods Patients presenting to orthopedic outpatient clinics completed questionnaires regarding methods of contact: home phone, cell phone, mailing address, and e-mail address. They reported currently available methods of contact, if they changed in the past five and ten years, and when they changed. Differences in the rates of change amongst methods were assessed via Fisher exact tests. Whether participants changed any of their contact information in the past five and ten years was determined via multivariate modeling, controlling for demographic variables. Results Among 152 patients, 51% changed at least one form of contact information within 5 years, and 66% changed at least one form within 10 years. The rate of change for each contact method was similar over five (15-28%) and ten years (26-41%). One patient changed all 4 methods of contact within the past five years, and seven within the past ten years. Females and younger patients were more likely to change some type of contact information. Conclusions The type of contact information least likely to change over five to ten years is influenced by demographic factors such as sex and age, with females and younger participants more likely to change some aspect of their contact information. Collecting all contact methods appears necessary to minimize patients lost to follow-up, especially as technological norms evolve. PMID:28359191

The (in)stability of 21st century orthopedic patient contact information and its implications on clinical research: A cross-sectional study.

PubMed

London, Daniel A; Stepan, Jeffrey G; Goldfarb, Charles A; Boyer, Martin I; Calfee, Ryan P

2017-04-01

In clinical research, minimizing patients lost to follow-up is essential for data validity. Researchers can employ better methodology to prevent patient loss. We examined how orthopedic surgery patients' contact information changes over time to optimize data collection for long-term outcomes research. Patients presenting to orthopedic outpatient clinics completed questionnaires regarding methods of contact: home phone, cell phone, mailing address, and e-mail address. They reported currently available methods of contact, if they changed in the past 5 and 10 years, and when they changed. Differences in the rates of change among methods were assessed via Fisher's exact tests. Whether participants changed any of their contact information in the past 5 and 10 years was determined via multivariate modeling, controlling for demographic variables. Among 152 patients, 51% changed at least one form of contact information within 5 years, and 66% changed at least one form within 10 years. The rate of change for each contact method was similar over 5 (15%-28%) and 10 years (26%-41%). One patient changed all four methods of contact within the past 5 years and seven within the past 10 years. Females and younger patients were more likely to change some type of contact information. The type of contact information least likely to change over 5-10 years is influenced by demographic factors such as sex and age, with females and younger participants more likely to change some aspect of their contact information. Collecting all contact methods appears necessary to minimize patients lost to follow-up, especially as technological norms evolve.

Self-Limiting Oxides on WSe2 as Controlled Surface Acceptors and Low-Resistance Hole Contacts.

PubMed

Yamamoto, Mahito; Nakaharai, Shu; Ueno, Keiji; Tsukagoshi, Kazuhito

2016-04-13

Transition metal oxides show much promise as effective p-type contacts and dopants in electronics based on transition metal dichalcogenides. Here we report that atomically thin films of under-stoichiometric tungsten oxides (WOx with x < 3) grown on tungsten diselenide (WSe2) can be used as both controlled charge transfer dopants and low-barrier contacts for p-type WSe2 transistors. Exposure of atomically thin WSe2 transistors to ozone (O3) at 100 °C results in self-limiting oxidation of the WSe2 surfaces to conducting WOx films. WOx-covered WSe2 is highly hole-doped due to surface electron transfer from the underlying WSe2 to the high electron affinity WOx. The dopant concentration can be reduced by suppressing the electron affinity of WOx by air exposure, but exposure to O3 at room temperature leads to the recovery of the electron affinity. Hence, surface transfer doping with WOx is virtually controllable. Transistors based on WSe2 covered with WOx show only p-type conductions with orders of magnitude better on-current, on/off current ratio, and carrier mobility than without WOx, suggesting that the surface WOx serves as a p-type contact with a low hole Schottky barrier. Our findings point to a simple and effective strategy for creating p-type devices based on two-dimensional transition metal dichalcogenides with controlled dopant concentrations.

Photometric studies of two solar type marginal contact binaries in the Small Magellanic Cloud

NASA Astrophysics Data System (ADS)

Shanti Priya, Devarapalli; Rukmini, Jagirdar

2018-04-01

Using the Optical Gravitational Lensing Experiment catalogue, two contact binaries were studied using data in the V and I bands. The photometric solutions for the V and I bands are presented for two contact binaries OGLE 003835.24-735413.2 (V1) and OGLE 004619.65-725056.2 (V2) in Small Maglellanic Cloud. The presented light curves are analyzed using the Wilson-Devinney code. The results show that the variables are in good thermal and marginal geometrical contact with features like the O’Connell effect in V1. The absolute dimensions are estimated and its dynamical evolution is inferred. They tend to be solar type marginal contact binaries. The 3.6-m Devasthal Optical Telescope and the 4.0-m International Liquid Mirror Telescope of the Aryabhatta Research Institute of Observational Sciences (ARIES, Nainithal) can facilitate the continuous monitoring of such kind of objects which will help in finding the reasons behind their period changes and their impact on the evolution of the clusters.

Low Temperature Ohmic Contact Formation of Ni2Si on N-type 4H-SiC and 6H-SiC

NASA Technical Reports Server (NTRS)

Elsamadicy, A. M.; Ila, D.; Zimmerman, R.; Muntele, C.; Evelyn, L.; Muntele, I.; Poker, D. B.; Hensley, D.; Hirvonen, J. K.; Demaree, J. D.;

Derivation of a continuum model and the energy law for moving contact lines with insoluble surfactants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Zhen, E-mail: matzz@nus.edu.sg; Xu, Shixin, E-mail: matxs@nus.edu.sg; Ren, Weiqing, E-mail: matrw@nus.edu.sg

2014-06-15

A continuous model is derived for the dynamics of two immiscible fluids with moving contact lines and insoluble surfactants based on thermodynamic principles. The continuum model consists of the Navier-Stokes equations for the dynamics of the two fluids and a convection-diffusion equation for the evolution of the surfactant on the fluid interface. The interface condition, the boundary condition for the slip velocity, and the condition for the dynamic contact angle are derived from the consideration of energy dissipations. Different types of energy dissipations, including the viscous dissipation, the dissipations on the solid wall and at the contact line, as wellmore » as the dissipation due to the diffusion of surfactant, are identified from the analysis. A finite element method is developed for the continuum model. Numerical experiments are performed to demonstrate the influence of surfactant on the contact line dynamics. The different types of energy dissipations are compared numerically.« less

Who's holding the baby? A prospective diary study of the contact patterns of mothers with an infant.

PubMed

Campbell, Patricia Therese; McVernon, Jodie; Shrestha, Niraj; Nathan, Paula M; Geard, Nicholas

2017-09-20

Models of infectious disease are increasingly utilising empirical contact data to quantify the number of potentially infectious contacts between age groups. While a growing body of data is being collected on contact patterns across many populations, less attention has been paid to the social contacts of young infants. We collected information on the social contacts of primary carers of young infants and investigated their potential for use as a proxy for contacts made by their infant. We recruited primary carers of infants under one year of age residing in two geographically, demographically and socioeconomically distinct local government areas of Melbourne, Australia - Boroondara and Hume - including a sub-group of Turkish-speaking participants. Participants recorded their own contacts in a paper diary and noted whether their infant was present or absent. Information collected included times at an address; description of location; and details on people contacted at the location. Descriptive summary measures and distributions of contacts by location type, intensity, day of contact and by age are reported. Of the 226 participants recruited, 220 completed diaries were returned. Participant contact patterns were similar across all groups, with respect to the types of locations, intensity and day of contact, with some variation in the number of unique daily contacts. The infant was present at around 85% of locations at which the primary carer contacted other individuals. The majority of contacts occurring when the infant was present were in Own Home (32%), Retail and Hospitality (18%) and Transport (18%) settings. The mean daily number of unique contacts by infants was estimated as 9.1, 8.7 and 6.5 in Boroondara, Hume (English) and Hume (Turkish), respectively, with a similar age distribution across each of our surveyed groups. Our demonstration that contact patterns of mothers with infants are reasonably robust to socioeconomic and cultural differences is a step forward in modelling infectious disease transmission. With infants spending most of their time in the company of their mother, contact patterns of mothers are a useful proxy measure of infant contact patterns. The age distribution of contacts made by infants estimated in this study may be used to supplement population-wide contact information commonly used in infectious disease transmission models.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chanana, Anuja; Mahapatra, Santanu, E-mail: santanu@dese.iisc.ernet.in

Investigation of a transition metal dichalcogenide (TMD)-metal interface is essential for the effective functioning of monolayer TMD based field effect transistors. In this work, we employ the Density Functional Theory calculations to analyze the modulation of the electronic structure of monolayer WS{sub 2} with chlorine doping and the relative changes in the contact properties when interfaced with gold and palladium. We initially examine the atomic and electronic structures of pure and doped monolayer WS{sub 2} supercell and explore the formation of midgap states with band splitting near the conduction band edge. Further, we analyze the contact nature of the puremore » supercell with Au and Pd. We find that while Au is physiosorbed and forms n-type contact, Pd is chemisorped and forms p-type contact with a higher valence electron density. Next, we study the interface formed between the Cl-doped supercell and metals and observe a reduction in the Schottky barrier height (SBH) in comparison to the pure supercell. This reduction found is higher for Pd in comparison to Au, which is further validated by examining the charge transfer occurring at the interface. Our study confirms that Cl doping is an efficient mechanism to reduce the n-SBH for both Au and Pd, which form different types of contact with WS{sub 2}.« less

Transmittance of tinted and UV-blocking disposable contact lenses.

PubMed

Harris, M G; Haririfar, M; Hirano, K Y

1999-03-01

Tinted and ultraviolet (UV)-blocking disposable contact lenses have become increasingly popular over the last decade. Wearers of UV-blocking contact lenses could benefit greatly by protecting their eyes from potential UV radiation damage. A Uvikon 930 dual beam spectrophotometer was used to measure three enhancement-tinted lenses (royal blue, evergreen, and aqua), two types of UV-blocking lenses, and two types of non-UV-blocking lenses. Enhancement-tinted lenses did show a decrease in transmittance at certain wavelengths on the visible spectrum, but they did not reduce the transmittance of UV radiation to the extent of the UV-blocking lenses designed specifically for this purpose.

Types of Eczema (Dermatitis)

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...

Observations, Roche Lobe Analysis, and Period Study of the Eclipsing Contact Binary System GM Canum Venaticorum

NASA Astrophysics Data System (ADS)

Alton, K. B.; Nelson, R. H.

2018-06-01

GM CVn is an eclipsing W UMa binary system (P = 0.366984 d) which has been largely neglected since its variability was first detected during the ROTSE campaign (1999-2000). Other than a single unfiltered light curve (LC) no other photometric data have been published. LC data collected in three bandpasses (B, V, and Rc) at UnderOak Observatory (UO) produced three new times of minimum for GM CVn. These along with other eclipse timings from the literature were used to update the linear ephemeris. Roche modeling to produce synthetic LC fits to the observed data was accomplished using binary maker 3, wdwint56a, and phoebe v.31a. Newly acquired radial velocity data were pivotal to defining the absolute and geometric parameters for this partially eclipsing binary system. An unspotted solution achieved the best Roche model fits for the multi-color LCs collected in 2013.

Effect of keyswitch design of desktop and notebook keyboards related to key stiffness and typing force.

PubMed

Bufton, Marcia J; Marklin, Richard W; Nagurka, Mark L; Simoneau, Guy G

2006-08-15

This study aimed to compare and analyse rubber-dome desktop, spring-column desktop and notebook keyboards in terms of key stiffness and fingertip typing force. The spring-column keyboard resulted in the highest mean peak contact force (0.86N), followed by the rubber dome desktop (0.68N) and the notebook (0.59N). All these differences were statistically significant. Likewise, the spring-column keyboard registered the highest fingertip typing force and the notebook keyboard the lowest. A comparison of forces showed the notebook (rubber dome) keyboard had the highest fingertip-to-peak contact force ratio (overstrike force), and the spring-column generated the least excess force (as a ratio of peak contact force). The results of this study could aid in optimizing computer key design that could possibly reduce subject discomfort and fatigue.

Impact of air-drying lens cases in various locations and positions.

PubMed

Wu, Yvonne T; Zhu, Hua; Willcox, Mark; Stapleton, Fiona

2010-07-01

To determine the rate and type of microbial contamination when contact lens cases are air-dried in two different positions (face up and face down) and in four different locations (toilet, bathroom, office, and bedroom). Unused contact lens cases (n = 97) were rinsed with 2-ml sterile phosphate buffered saline and then placed on facial tissue paper in different locations: humid (toilet and bathroom) and non-humid (office and bedroom) and air-dried at room temperature. After 24 h, the contact lens cases were collected and sampled for microbial numbers and microbial types identified using standard techniques. The microbial profile and the rate of contamination between different locations and positions were compared. Irrespective of the air-drying location, contact lens cases positioned face up had a significantly higher contamination rate (34/48, 71%) compared with contact lens cases air-dried face down (6/49, 12%) (p < 0.001). For those contact lens cases air-dried face up, there was more contamination when placed in humid environments (toilet and bathroom) than in the non-humid environments (office and bedroom) (p = 0.01). However, the contact lens case contamination rate among various locations was similar when contact lens cases were air-dried face down. Total microorganisms recovered from contact lens cases ranged from 0 to 275 colony forming unit per well. The most frequently recovered microorganisms from the contaminated contact lens cases were coagulase-negative Staphylococci, fungi, and Bacillus spp. Thirty-three percent (13/40) of contact lens cases were contaminated with multiple species. Small numbers of microorganisms from the environment may contaminate contact lens cases while cases are air-dried face up. Cases air-dried in humid environments have higher levels of microbial contamination; this is particularly true when contact lens cases are positioned face up. On the basis of this limited study, we would recommend contact lens cases be air-dried face down.

Planar varactor frequency multiplier devices with blocking barrier

NASA Technical Reports Server (NTRS)

Lieneweg, Udo (Inventor); Frerking, Margaret A. (Inventor); Maserjian, Joseph (Inventor)

1994-01-01

The invention relates to planar varactor frequency multiplier devices with a heterojunction blocking barrier for near millimeter wave radiation of moderate power from a fundamental input wave. The space charge limitation of the submillimeter frequency multiplier devices of the BIN(sup +) type is overcome by a diode structure comprising an n(sup +) doped layer of semiconductor material functioning as a low resistance back contact, a layer of semiconductor material with n-type doping functioning as a drift region grown on the back contact layer, a delta doping sheet forming a positive charge at the interface of the drift region layer with a barrier layer, and a surface metal contact. The layers thus formed on an n(sup +) doped layer may be divided into two isolated back-to-back BNN(sup +) diodes by separately depositing two surface metal contacts. By repeating the sequence of the drift region layer and the barrier layer with the delta doping sheet at the interfaces between the drift and barrier layers, a plurality of stacked diodes is formed. The novelty of the invention resides in providing n-type semiconductor material for the drift region in a GaAs/AlGaAs structure, and in stacking a plurality of such BNN(sup +) diodes stacked for greater output power with and connected back-to-back with the n(sup +) GaAs layer as an internal back contact and separate metal contact over an AlGaAs barrier layer on top of each stack.

Thermal Interaction of Contact Lens Eyewear and 94 GHz Ocular Exposures

DTIC Science & Technology

2008-09-01

AFRL-RH-BR-TR-2008-0071 ` Thermal Interaction of Contact Lens Eyewear and 94 GHz Ocular Exposures John D’Andrea Carrie C. Crane...THERMAL INTERACTION OF CONTACT LENS EYEWEAR AND 94 GHz OCULAR EXPOSURES D’Andrea JA 1, Crane CC1, Hatcher DJ1, Marchello DR1, Ziriax JM1...MM-YYYY) 12-20-2005 2. REPORT TYPE Technical Report 3. DATES COVERED (From - To) 2004-2005 THERMAL INTERACTION OF CONTACT LENS EYEWEAR AND 94

Transient and steady state viscoelastic rolling contact

NASA Technical Reports Server (NTRS)

Padovan, J.; Paramadilok, O.

1985-01-01

Based on moving total Lagrangian coordinates, a so-called traveling Hughes type contact strategy is developed. Employing the modified contact scheme in conjunction with a traveling finite element strategy, an overall solution methodology is developed to handle transient and steady viscoelastic rolling contact. To verify the scheme, the results of both experimental and analytical benchmarking is presented. The experimental benchmarking includes the handling of rolling tires up to their upper bound behavior, namely the standing wave response.

Influence of Thermal Contact Resistance of Aluminum Foams in Forced Convection: Experimental Analysis

PubMed Central

Venettacci, Simone

2017-01-01

In this paper, the heat transfer performances of aluminum metal foams, placed on horizontal plane surface, was evaluated in forced convection conditions. Three different types of contacts between the sample and the heated base plate have been investigated: simple contact, brazed contact and grease paste contact. First, in order to perform the study, an ad hoc experimental set-up was built. Second, the value of thermal contact resistance was estimated. The results show that both the use of a conductive paste and the brazing contact, realized by means of a copper electro-deposition, allows a great reduction of the global thermal resistance, increasing de facto the global heat transfer coefficient of almost 80%, compared to the simple contact case. Finally, it was shown that, while the contribution of thermal resistance is negligible for the cases of brazed and grease paste contact, it is significantly high for the case of simple contact. PMID:28783052

Effects of communication media choice on the quality and efficacy of emergency calls assisted by a mobile nursing protocol tool.

PubMed

Castro, Luis A; Favela, Jesus; Garcia-Peña, Carmen

2014-11-01

The transition from paper to electronic-based records in the healthcare industry has posed several challenges to conventional medical practices. The introduction of technology in day-to-day medical and nursing practices deserves careful consideration. In this work, we report the results of a controlled experiment to compare nurses' consultation in emergency calls in six different conditions. We studied the effect that the type of communication media (face-to-face, telephone, videoconference) and type of nursing protocol media (paper-based, electronic-based) can have on consultation time, mistakes made, pauses during consultation, eye contact, and efficacy of the consultation. We found that the type of communication media has an effect on consultation time; on average, fewer mistakes were made during telephone-based consultations; for eye contact, there were significantly fewer eye contacts during face-to-face than during videoconference consultations; finally, the type of communication media or protocol media did not have any effect in the efficacy of the consultation.

The differential relationship between mental contamination and the core dimensions of contact contamination fear.

PubMed

Melli, Gabriele; Bulli, Francesco; Carraresi, Claudia; Tarantino, Federica; Gelli, Simona; Poli, Andrea

2017-01-01

Two types of contamination fear are recognized: contact and mental contamination. Contact contamination appears to be motivated both by harm avoidance and disgust avoidance. This study aimed to examine the relationships between disgust propensity, mental contamination and contact contamination while differentiating between harm avoidance and disgust avoidance in contact contamination. 169 OCD patients completed a set of questionnaires assessing mental contamination, contact contamination, disgust propensity, OCD, anxiety and depression. 1) Contact contamination based on disgust avoidance was more strongly associated with mental contamination and disgust propensity than contact contamination based on harm avoidance; 2) mental contamination significantly predicted contact contamination based on disgust avoidance, while it did not predict contact contamination based on harm avoidance; 3) mental contamination had a significant mediational role in the relationship between disgust propensity and contact contamination motivated by disgust avoidance. Mental contamination plays a role in contact contamination fear when disgust is primarily experienced. Copyright © 2016 Elsevier Ltd. All rights reserved.

Project Execution Plan for the Near Shore Survey SOCAL ASW (Southern California Anti-Submarine Warfare) Range,

DTIC Science & Technology

1985-01-01

closest source and availability of vehicles for transport of personnel and gear? (a) Type_______ (b) Location________ (c) Contact_____ I ~ ~~~(d) Phone No...c) Contact_________ -. ~~~(d) Phone No.________ (5) Is portable electrical power generation equipment available? Type: (a) AC ___Volts ___Capacity...military diving unit nearby? -* ~ ~ ~ ~ a Location____ _____ (b) Distance ___ _____ (c) Phone No.___ ______ (d) CO __ _ _ _ _ _ _ _ _ (e) MDV k (2) Are

Ultra-Low Power Fiber-Coupled Gallium Arsenide Photonic Crystal Cavity Electro-Optical Modulator

DTIC Science & Technology

2011-04-11

1185 (2009). 6. B. R. Bennett, R. A. Soref, and J. A. Del Alamo, “Carrier-induced change in refractive index of InP , GaAs, and InGaAsP,” IEEE J...Finally, a Au/Ge/Ni/Au n-type contact and a Au/ Zn /Au p-type contact were deposited and the membranes were released by wet etching the sacrificial

Mast Cells Limit the Exacerbation of Chronic Allergic Contact Dermatitis in Response to Repeated Allergen Exposure.

PubMed

Gimenez-Rivera, Vladimir-Andrey; Siebenhaar, Frank; Zimmermann, Carolin; Siiskonen, Hanna; Metz, Martin; Maurer, Marcus

2016-12-01

Allergic contact dermatitis is a chronic T cell-driven inflammatory skin disease that is caused by repeated exposure to contact allergens. Based on murine studies of acute contact hypersensitivity, mast cells (MCs) are believed to play a role in its pathogenesis. The role of MCs in chronic allergic contact dermatitis has not been investigated, in part because of the lack of murine models for chronic contact hypersensitivity. We developed and used a chronic contact hypersensitivity model in wild-type and MC-deficient mice and assessed skin inflammatory responses to identify and characterize the role of MCs in chronic allergic contact dermatitis. Ear swelling chronic contact hypersensitivity responses increased markedly, up to 4-fold, in MC-deficient Kit W-sh/W-sh (Sash) and MCPT5-Cre + iDTR + mice compared with wild-type mice. Local engraftment with MCs protected Sash mice from exacerbated ear swelling after repeated oxazolone challenge. Chronic contact hypersensitivity skin of Sash mice exhibited elevated levels of IFN-γ, IL-17α, and IL-23, as well as increased accumulation of Ag-specific IFN-γ-producing CD8 + tissue-resident memory T (T RM ) cells. The CD8 + T cell mitogen IL-15, which was increased in oxazolone-challenged skin of Sash mice during the accumulation of cutaneous T RM cells, was efficiently degraded by MCs in vitro. MCs protect from the exacerbated allergic skin inflammation induced by repeated allergen challenge, at least in part, via effects on CD8 + T RM cells. MCs may notably influence the course of chronic allergic contact dermatitis. A better understanding of their role and the underlying mechanisms may lead to better approaches for the treatment of this common, disabling, and costly condition. Copyright © 2016 by The American Association of Immunologists, Inc.

Pinning of the Contact Line during Evaporation on Heterogeneous Surfaces: Slowdown or Temporary Immobilization? Insights from a Nanoscale Study.

PubMed

Zhang, Jianguo; Müller-Plathe, Florian; Leroy, Frédéric

2015-07-14

The question of the effect of surface heterogeneities on the evaporation of liquid droplets from solid surfaces is addressed through nonequilibrium molecular dynamics simulations. The mechanism behind contact line pinning which is still unclear is discussed in detail on the nanoscale. Model systems with the Lennard-Jones interaction potential were employed to study the evaporation of nanometer-sized cylindrical droplets from a flat surface. The heterogeneity of the surface was modeled through alternating stripes of equal width but two chemical types. The first type leads to a contact angle of 67°, and the other leads to a contact angle of 115°. The stripe width was varied between 2 and 20 liquid-particle diameters. On the surface with the narrowest stripes, evaporation occurred at constant contact angle as if the surface was homogeneous, with a value of the contact angle as predicted by the regular Cassie-Baxter equation. When the width was increased, the contact angle oscillated during evaporation between two boundaries whose values depend on the stripe width. The evaporation behavior was thus found to be a direct signature of the typical size of the surface heterogeneity domains. The contact angle both at equilibrium and during evaporation could be predicted from a local Cassie-Baxter equation in which the surface composition within a distance of seven fluid-particle diameters around the contact line was considered, confirming the local nature of the interactions that drive the wetting behavior of droplets. More importantly, we propose a nanoscale explanation of pinning during evaporation. Pinning should be interpreted as a drastic slowdown of the contact line dynamics rather than a complete immobilization of it during a transition between two contact angle boundaries.

Frequency-risk and duration-risk relations between occupational livestock contact and methicillin-resistant Staphylococcus aureus carriage among workers in Guangdong, China.

PubMed

Ye, Xiaohua; Liu, Weidong; Fan, Yanping; Wang, Xiaolin; Zhou, Junli; Yao, Zhenjiang; Chen, Sidong

2015-07-01

Increasing evidence indicates a strong association between occupational livestock contact and methicillin-resistant Staphylococcus aureus (MRSA) carriage. However, it remains unclear whether there are frequency-risk and duration-risk relations between occupational livestock contact and human MRSA carriage. A cross-sectional survey was conducted in Guangdong, China, using a multistage sampling method. Participants were interviewed and provided a nasal swab for S aureus analysis. All MRSA isolates were genotyped by multilocus sequence typing. The dose-response relation was examined using logistic regression models. Among the 1,860 participants, 1.4% of controls tested positive for MRSA (characterized as sequence type [ST] 59 and ST7), and 7% of workers with livestock contact tested positive for MRSA (characterized as ST9, ST59, and ST7). There was a 5.31 times increased risk of MRSA carriage corresponding to occupational livestock contact (odds ratio = 6.31; 95% confidence interval, 3.44-11.57) using no contact as reference. We found frequency and short-term duration of occupational livestock contact were associated with increased risk of MRSA carriage in a dose-response manner. These significant trends were observed consistently among workers with occupational pig contact. However, no long-term duration-risk increasing trend was observed for occupational livestock or pig contact. Our findings suggest that there may be dose-response relations between occupational livestock contact and human MRSA carriage. Nasal MRSA clonal complex 9 is not found in controls, but it is found in workers with livestock contact. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Relationship between social network, social support and health behaviour in people with type 1 and type 2 diabetes: cross-sectional studies.

PubMed

Hempler, Nana F; Joensen, Lene E; Willaing, Ingrid

2016-02-29

Psychosocial and behavioural aspects of diabetes may differ according to diabetes type. This study compared people with type 1 and type 2 diabetes with respect to social relations (cohabitation status, contact with the social network and social support) and health behaviours (diet and physical activity). Furthermore, we examined whether potential differences in health behaviour between people with type 1 and type 2 diabetes were influenced by education level and social relations. We conducted two cross-sectional surveys consisting of people with type 2 diabetes (N = 1081) and type 1 diabetes (N = 2419) from a specialist diabetes clinic. Gender-stratified stepwise multiple regression models assessed differences by diabetes type and other variables of interest. Significant associations were found between diabetes type and social network, social support and health behaviour. No differences were observed regarding cohabitation status. People with type 2 diabetes were less physically active, less likely to follow recommended diet (men), had fewer contacts with family and friends and were less certain of counting on help in case of severe illness than people with type 1 diabetes. No impact of education level, social network and social support were observed concerning differences in health behaviours by diabetes type; however, in women, the association between physical activity and diabetes type was not significant after adjustment for social relations and education level. People with type 2 diabetes had less contact with the social network, less certainty about support in case of severe illness and fewer healthy behaviours than people with type 1 diabetes. It may be important to draw attention to differences in health behaviours and social relations between people with type 1 and type 2 diabetes in diabetes care, patient education and support initiatives.

Electron-selective contacts via ultra-thin organic interface dipoles for silicon organic heterojunction solar cells

NASA Astrophysics Data System (ADS)

Reichel, Christian; Würfel, Uli; Winkler, Kristina; Schleiermacher, Hans-Frieder; Kohlstädt, Markus; Unmüssig, Moritz; Messmer, Christoph A.; Hermle, Martin; Glunz, Stefan W.

2018-01-01

In the last years, novel materials for the formation of electron-selective contacts on n-type crystalline silicon (c-Si) heterojunction solar cells were explored as an interfacial layer between the metal electrode and the c-Si wafer. Besides inorganic materials like transition metal oxides or alkali metal fluorides, also interfacial layers based on organic molecules with a permanent dipole moment are promising candidates to improve the contact properties. Here, the dipole effect plays an essential role in the modification of the interface and effective work function of the contact. The amino acids L-histidine, L-tryptophan, L-phenylalanine, glycine, and sarcosine, the nucleobase adenine, and the heterocycle 4-hydroxypyridine were investigated as dipole materials for an electron-selective contact on the back of p- and n-type c-Si with a metal electrode based on aluminum (Al). Furthermore, the effect of an added fluorosurfactant on the resulting contact properties was examined. The performance of n-type c-Si solar cells with a boron diffusion on the front was significantly increased when L-histidine and/or the fluorosurfactant was applied as a full-area back surface field. This improvement was attributed to the modification of the interface and the effective work function of the contact by the dipole material which was corroborated by numerical device simulations. For these solar cells, conversion efficiencies of 17.5% were obtained with open-circuit voltages (Voc) of 625 mV and fill factors of 76.3%, showing the potential of organic interface dipoles for silicon organic heterojunction solar cells due to their simple formation by solution processing and their low thermal budget requirements.

Concentrating Solar Power Projects - ISCC Kuraymat | Concentrating Solar

Science.gov Websites

: 20.0 MW Gross: 20.0 MW Status: Operational Start Year: 2011 Do you have more information, corrections . Contact(s): Bothayna Rashed Company: NREA Start Production: June 2011 Project Type: Commercial

Unexpected Languages: Multilingualism and Contact in Eighteenth- and Nineteenth-Century North America

ERIC Educational Resources Information Center

Phillips, Lisa

2011-01-01

This exploration of the languages of contact in the North American British-US borderlands in the period between 1783 and 1860 provides insights into the types of extended contact that occurred in the areas north of 42[degrees] and south of 50[degrees]. Although multilingualism was the norm in the Old Northwest and the old Oregon Territory during…

Birth Family Contact for Children in Care: How Much? How Often? Who with?

ERIC Educational Resources Information Center

Atwool, Nicola

2013-01-01

Irrespective of type of placement, contact with the birth family is one of the more contentious issues in decision-making for children in care. Despite widespread belief that contact with the birth family is beneficial for children and young people in care, this aspect of children's care experience has not received a great deal of attention. In…

The Role of Language Contact in Semantic Change: "Ser" and "Estar"--A Response to Geeslin and Guijarro-Fuentes

ERIC Educational Resources Information Center

Klee, Carol A.

2008-01-01

The role of language contact in linguistic change remains a polemic issue in the field of contact linguistics. Many researchers (Weinreich, 1953; Lefebvre, 1985; Prince, 1988; Silva-Corvalan, 1994; King, 2000; Sankoff, 2002; Labov, 2007) believe that there are limits on the types of linguistic patterns that can be transmitted across languages,…

Computerized Design and Analysis of Face-Milled, Uniform Tooth Height Spiral Bevel Gear Drives

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Wang, Anngwo; Handschuh, R. F.

1996-01-01

Face-milled spiral bevel gears with uniform tooth height are considered. An approach is proposed for the design of low noise and localized bearing contact of such gears. The approach is based on the mismatch of contacting surfaces and permits two types of bearing contact either directed longitudinally or across the surface to be obtained. A Tooth Contact Analysis (TCA) computer program was developed. This analysis was used to determine the influence of misalignment on meshing and contact of the spiral bevel gears. A numerical example that illustrates the developed theory is provided.

A Simulation Study Comparing Epidemic Dynamics on Exponential Random Graph and Edge-Triangle Configuration Type Contact Network Models

PubMed Central

Rolls, David A.; Wang, Peng; McBryde, Emma; Pattison, Philippa; Robins, Garry

2015-01-01

We compare two broad types of empirically grounded random network models in terms of their abilities to capture both network features and simulated Susceptible-Infected-Recovered (SIR) epidemic dynamics. The types of network models are exponential random graph models (ERGMs) and extensions of the configuration model. We use three kinds of empirical contact networks, chosen to provide both variety and realistic patterns of human contact: a highly clustered network, a bipartite network and a snowball sampled network of a “hidden population”. In the case of the snowball sampled network we present a novel method for fitting an edge-triangle model. In our results, ERGMs consistently capture clustering as well or better than configuration-type models, but the latter models better capture the node degree distribution. Despite the additional computational requirements to fit ERGMs to empirical networks, the use of ERGMs provides only a slight improvement in the ability of the models to recreate epidemic features of the empirical network in simulated SIR epidemics. Generally, SIR epidemic results from using configuration-type models fall between those from a random network model (i.e., an Erdős-Rényi model) and an ERGM. The addition of subgraphs of size four to edge-triangle type models does improve agreement with the empirical network for smaller densities in clustered networks. Additional subgraphs do not make a noticeable difference in our example, although we would expect the ability to model cliques to be helpful for contact networks exhibiting household structure. PMID:26555701

The role of type III secretion system and lens material on adhesion of Pseudomonas aeruginosa to contact lenses.

PubMed

Shen, Elizabeth P; Tsay, Ruey-Yug; Chia, Jean-San; Wu, Semon; Lee, Jing-Wen; Hu, Fung-Rong

2012-09-21

To determine the distribution of invasive and cytotoxic genotypes among ocular isolates of P. aeruginosa and investigate the influence of the type III secretion system (T3SS) on adhesion to conventional, cosmetic, and silicone hydrogel contact lenses (CL). Clinical isolates from 2001 to 2010 were analyzed by multiplex PCR for exoS, exoU, and exoT genes. Bacterial adhesion to etafilcon, nelfilcon (gray colored), balafilcon, and galyfilcon CL with or without artificial tear fluid (ATF) incubation were compared. Surface characteristics were determined with scanning electron microscopy (SEM). Among 87 total isolates, 64 strains were from microbial keratitis cases. CL-related microbial keratitis (CLMK) isolates were mostly of the cytotoxic genotype (expressing exoU) (P = 0.002). No significant differences were found in bacterial adhesion to all types of CL between the genotypes under T3SS-inducing conditions. A trend for least bacterial adhesion of galyfilcon compared to the other CL was noted for both genotypes. Needle complex pscC mutants adhered less to all materials than the wild type (P < 0.05), indicating a role of the T3SS in contact lens adhesion. ATF-incubated CL had significantly more bacterial adhesion (P < 0.05). SEM showed most of the bacteria adhering on CL surfaces. CLMK isolates were mostly of cytotoxic genotype. Different genotypes did not significantly differ in its adhesion to various CL. T3SS and other adhesins are involved in bacteria-contact lens adhesion through complex interactions. Contact lens materials may also play an important role in the adherence of both genotypes of P. aeruginosa.

Fine structural survey of the intermediate subnucleus of the nucleus tractus solitarii and its glossopharyngeal afferent terminals.

PubMed

Hayakawa, Tetsu; Maeda, Seishi; Tanaka, Koichi; Seki, Makoto

2005-10-01

The intermediate subnucleus of the nucleus tractus solitarii (imNTS) receives somatosensory inputs from the soft palate and pharynx, and projects onto the nucleus ambiguus, thus serving as a relay nucleus for swallowing. The ultrastructure and synaptology of the rat imNTS, and its glossopharyngeal afferent terminals, have been examined with cholera toxin-conjugated horseradish peroxidase (CT-HRP) as an anterograde tracer. The imNTS contained oval or ellipsoid-shaped, small to medium-sized neurons (18.2 x 11.4 microm) with little cytoplasm, few cell organelles and an irregularly shaped nucleus. The cytoplasm often contained one or two nucleolus-like stigmoid bodies. The average number of axosomatic terminals was 1.8 per profile. About 83% of them contained round vesicles and formed asymmetric synaptic contacts (Gray's type I), while about 17% contained pleomorphic vesicles and formed symmetric synaptic contacts (Gray's type II). The neuropil contained small or large axodendritic terminals, and about 92% of them were Gray's type I. When CT-HRP was injected into the nodose ganglion, many labeled terminals were found in the imNTS. All anterogradely labeled terminals contacted dendrites but not somata. The labeled terminals were usually large (2.69+/-0.09 mum) and exclusively of Gray's type I. They often contacted more than two dendrites, were covered with glial processes, and formed synaptic glomeruli. A small unlabeled terminal occasionally made an asymmetric synaptic contact with a large labeled terminal. The large glossopharyngeal afferent terminals and the neurons containing stigmoid bodies characterized the imNTS neurons that received pharyngeal afferents.

Tuberculosis

USGS Publications Warehouse

Friend, Milton

1999-01-01

Avian tuberculosis is usually caused by the bacterium Mycobacterium avium. At least 20 different types of M. avium have been identified, only three of which are known to cause disease in birds. Other types of Mycobacterium rarely cause tuberculosis in most avian species; however, parrots, macaws, and other large perching birds are susceptible to human and bovine types of tuberculosis bacilli. Avian tuberculosis generally is transmitted by direct contact with infected birds, ingestion of contaminated feed and water, or contact with a contaminated environment. Inhalation of the bacterium can cause respiratory tract infections. Wild bird studies in the Netherlands disclosed tuberculosis-infected puncture-type injuries in birds of prey that fight at the nest site (kestrels) or on the ground (buteo-type buzzards), but tuberculosisinfected injuries were not found in accipiters (falco

Inferring Epidemic Contact Structure from Phylogenetic Trees

PubMed Central

Leventhal, Gabriel E.; Kouyos, Roger; Stadler, Tanja; von Wyl, Viktor; Yerly, Sabine; Böni, Jürg; Cellerai, Cristina; Klimkait, Thomas; Günthard, Huldrych F.; Bonhoeffer, Sebastian

2012-01-01

Contact structure is believed to have a large impact on epidemic spreading and consequently using networks to model such contact structure continues to gain interest in epidemiology. However, detailed knowledge of the exact contact structure underlying real epidemics is limited. Here we address the question whether the structure of the contact network leaves a detectable genetic fingerprint in the pathogen population. To this end we compare phylogenies generated by disease outbreaks in simulated populations with different types of contact networks. We find that the shape of these phylogenies strongly depends on contact structure. In particular, measures of tree imbalance allow us to quantify to what extent the contact structure underlying an epidemic deviates from a null model contact network and illustrate this in the case of random mixing. Using a phylogeny from the Swiss HIV epidemic, we show that this epidemic has a significantly more unbalanced tree than would be expected from random mixing. PMID:22412361

Friction drive position transducer

NASA Astrophysics Data System (ADS)

Waclawik, Ronald E.; Cayer, James L.; Lapointe, Kenneth M.

1991-10-01

A spring force loaded contact wheel mounted in a stationary position relative to a reciprocating shaft is disclosed. The apparatus of the present invention includes a tensioning assembly for maintaining absolute contact between the contact wheel and the reciprocating shaft wherein the tensioning assembly urges the contact wheel against the shaft to maintain contact therebetween so that the wheel turns as the shaft is linearly displaced. A rotary encoding device is coupled to the wheel for translating the angular and rotational movement thereof into an electronic signal for providing linear displacement information and derivative data with respect to displacement of the shaft. Absolute friction contact and cooperative interaction between the shaft and the contact wheel is further enhanced in the preferred embodiment by advantageously selecting the types of surface finish and the amount of surface area of the contact wheel relative to the surface condition of the shaft as well as by reducing the moment of inertia of the contact wheel.

Friction drive position transducer

NASA Astrophysics Data System (ADS)

Waclawik, Ronald E.; Cayer, James L.; Lapointe, Kenneth M.

1993-06-01

A spring force loaded contact wheel mounted in a stationary position relative to a reciprocating shaft is disclosed. The apparatus of the present invention includes a tensioning assembly for maintaining absolute contact between the contact wheel and the reciprocating shaft wherein the tensioning assembly urges the contact wheel against the shaft to maintain contact there between so that the wheel turn as the shaft is linearly displaced. A rotary encoding device is coupled to the wheel for translating the angular and rotational movement thereof into an electronic signal for providing linear displacement information and derivative data with respect to displacement of the shaft. Absolute friction contact and cooperative interaction between the shaft and the contact wheel is further enhanced in the preferred embodiment by advantageously selecting the type of surface finish and the amount of surface area of the contact wheel relative to the surface condition of the shaft as well as by reducing the moment of inertia of the contact wheel.

Low resistivity contacts to YBa2Cu3O(7-x) superconductors

NASA Technical Reports Server (NTRS)

Hsi, Chi-Shiung; Haertling, Gene H.

1991-01-01

Silver, gold, platinum, and palladium metals were investigated as electroding materials for the YBa2Cu3O(7-x) superconductors. Painting, embedding, and melting techniques were used to apply the electrodes. Contact resistivities were determined by: (1) type of electrode; (2) firing conditions; and (3) application method. Electrodes fired for long times exhibited lower contact resistivities than those fired for short times. Low-resistivity contacts were found for silver and gold electrodes. Silver, which made good ohmic contact to the YBa2Cu3O(7-x) superconductor with low contact resistivities was found to be the best electroding material among the materials evaluated in this investigation.

Investigation on Plasma Jet Flow Phenomena During DC Air Arc Motion in Bridge-Type Contacts

NASA Astrophysics Data System (ADS)

Zhai, Guofu; Bo, Kai; Chen, Mo; Zhou, Xue; Qiao, Xinlei

2016-05-01

Arc plasma jet flow in the air was investigated under a bridge-type contacts in a DC 270 V resistive circuit. We characterized the arc plasma jet flow appearance at different currents by using high-speed photography, and two polished contacts were used to search for the relationship between roughness and plasma jet flow. Then, to make the nature of arc plasma jet flow phenomena clear, a simplified model based on magnetohydrodynamic (MHD) theory was established and calculated. The simulated DC arc plasma was presented with the temperature distribution and the current density distribution. Furthermore, the calculated arc flow velocity field showed that the circular vortex was an embodiment of the arc plasma jet flow progress. The combined action of volume force and contact surface was the main reason of the arc jet flow. supported by National Natural Science Foundation of China (Nos. 51307030, 51277038)

Reliability improvements in tunable Pb1-xSnxSe diode lasers

NASA Technical Reports Server (NTRS)

Linden, K. J.; Butler, J. F.; Nill, K. W.; Reeder, R. E.

1980-01-01

Recent developments in the technology of Pb-salt diode lasers which have led to significant improvements in reliability and lifetime, and to improved operation at very long wavelengths are described. A combination of packaging and contacting-metallurgy improvements has led to diode lasers that are stable both in terms of temperature cycling and shelf-storage time. Lasers cycled over 500 times between 77 K and 300 K have exhibited no measurable changes in either electrical contact resistance or threshold current. Utilizing metallurgical contacting process, both lasers and experimental n-type and p-type bulk materials are shown to have electrical contact resistance values that are stable for shelf storage periods well in excess of one year. Problems and experiments which have led to devices with improved performance stability are discussed. Stable device configurations achieved for material compositions yielding lasers which operate continuously at wavelengths as long as 30.3 micrometers are described.

Method for fabricating solar cells having integrated collector grids

NASA Technical Reports Server (NTRS)

Evans, J. C., Jr. (Inventor)

1979-01-01

A heterojunction or Schottky barrier photovoltaic device comprising a conductive base metal layer compatible with and coating predominately the exposed surface of the p-type substrate of the device such that a back surface field region is formed at the interface between the device and the base metal layer, a transparent, conductive mixed metal oxide layer in integral contact with the n-type layer of the heterojunction or Schottky barrier device having a metal alloy grid network of the same metal elements of the oxide constituents of the mixed metal oxide layer embedded in the mixed metal oxide layer, an insulating layer which prevents electrical contact between the conductive metal base layer and the transparent, conductive metal oxide layer, and a metal contact means covering the insulating layer and in intimate contact with the metal grid network embedded in the transparent, conductive oxide layer for conducting electrons generated by the photovoltaic process from the device.

Is email a reliable means of contacting authors of previously published papers? A study of the Emergency Medicine Journal for 2001.

PubMed

O'Leary, F

2003-07-01

To determine whether it is possible to contact authors of previously published papers via email. A cross sectional study of the Emergency Medicine Journal for 2001. 118 articles were included in the study. The response rate from those with valid email addresses was 73%. There was no statistical difference between the type of email address used and the address being invalid (p=0.392) or between the type of article and the likelihood of a reply (p=0.197). More responses were obtained from work addresses when compared with Hotmail addresses (86% v 57%, p=0.02). Email is a valid means of contacting authors of previously published articles, particularly within the emergency medicine specialty. A work based email address may be a more valid means of contact than a Hotmail address.

Allergic contact dermatitis to nickel: modified in vitro test protocols for better detection of allergen-specific response.

PubMed

Spiewak, Radoslaw; Moed, Heleen; von Blomberg, Brigitta Mary E; Bruynzeel, Derk P; Scheper, Rik J; Gibbs, Susan; Rustemeyer, Thomas

2007-02-01

To date, no in vitro test is suitable for routine diagnosis of contact allergy. The aim of our study was to establish improved in vitro test protocol for the detection of antigen-specific responses of lymphocytes from patients with allergic contact dermatitis to nickel (Ni-ACD). Blood leucocytes from 14 Ni-ACD patients and 14 controls were cultured in the presence of 'cytokine cocktails' skewing lymphocytes towards 'type 1' [interferon-gamma (IFN-gamma)-secreting] or 'type 2' [interleukin (IL)-5 and IL-13-secreting] phenotypes. The cocktails consisted of IL-7 and, respectively, either IL-12 or IL-4. Cell responses to nickel were measured with enzyme-linked immunospot assay (ELISpot), enzyme-linked immunosorbent assay (ELISA), and lymphocyte proliferation test (LPT). Significant differences between patients with Ni-ACD and controls were found for the 'type 2' cytokines IL-13 and IL-5, with further increase of allergen-specific responses occurring when cultures were supplemented with IL-7 and IL-4. No significant differences were found for IFN-gamma. The best correlate to clinical diagnosis was LPT with 'type 2' skewing (r= 0.739, P < 0.001), followed by IL-13 ELISpot with 'type 2' skewing (r= 0.654, P < 0.001). The non-radioactive method that correlated best with LPT was IL-2 ELISpot (r= 0.809, P < 0.001). Overall, we conclude that combining ELISpot assay with proposed modifications of culture conditions improves detection of specific lymphocyte responses in contact allergy to nickel.

Three cases of paralytic poliomyelitis associated with type 3 vaccine poliovirus strains in Bulgaria.

PubMed

Korsun, Neli; Kojouharova, Mira; Vladimirova, Nadezhda; Fiore, Lucia; Litvinenko, Ivan; Buttinelli, Gabriele; Fiore, Stefano; Voynova-Georgieva, Violeta; Mladenova, Zornitsa; Georgieva, Daniela

2009-09-01

Oral poliovirus vaccine (OPV) can cause, in extremely rare cases vaccine-associated paralytic poliomyelitis in recipients, or contacts of vaccinees. Three cases of vaccine-associated paralytic poliomyelitis (two contacts and one recipient) occurred in the Bourgas region of Bulgaria in the spring of 2006. The first two cases, notified as acute flaccid paralysis, were 55 days old unvaccinated twin brothers, having been in contact with vaccinees. The third case concerned a 4-month-old infant who had received the first OPV dose 37 days prior to the onset of illness. Complete clinical, epidemiological, virological, serological and molecular investigations of the children with paralysis and their contacts were undertaken. In all the three cases type 3 polioviruses were isolated from fecal samples and characterized as Sabin-like poliovirus strains. Type 3 polioviruses isolated from the twin brothers demonstrated by sequence analysis U-to-C back mutation at nt 472 of the 5' UTR, known to correlate with neurovirulence, and mutation in the VP1 region. Type 3 poliovirus isolated from the third child demonstrated in the 3D sequenced region a recombination with Sabin type 1 poliovirus. In the latter region, three silent mutations and one, resulting in amino acid substitution, were also observed. The clinical, epidemiological and virological data and the neurological sequelae observed 60 days following the onset of paralysis, confirmed the diagnosis of vaccine-associated paralytic poliomyelitis in all the three patients.

Process for recovering hydrocarbons from a diatomite-type ore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, B.W.

1983-02-15

A process for recovering hydrocarbons from a diatomite-type ore which comprises contacting the diatomite ore with a C/sub 4/-C/sub 10/ alcohol and thereafter contacting the diatomite ore-alcohol mixture with an aqueous alkaline solution to separate a hydrocarbon-alcohol phase and an alkaline aqueous phase containing the stripped diatomite ore. Thereafter, the alcohol is distilled off from the hydrocarbon phase and recycled back into the initial process.

Limits on Spin-independent Couplings of Light Dark Matter WIMPs with a p-type Point-contact Germanium Detector

NASA Astrophysics Data System (ADS)

Lin, S. T.; Wong, H. T.

New limits on spin-independent WIMP-nucleon coupling using 39.5 kg-days of data taken with a p-type point-contact germanium detector with fiducial mass of 840 g at the Kuo-Sheng Reactor Neutrino Laboratory (KSNL) is presented. Charactering and understanding the anomalous surface behaviour is of particular significance to this study. The slow rise-time of surface events is identified via software pulse shape analysis techniques. In addition, the signal-retaining and background-rejecting efficiencies are implied to clarify the actual bulk and surface events in the mixed regime at sub-keV range. Both efficiencies are evaluated with calibration sources and a novel n-type point-contact germanium detector. Efficiencies-corrected background spectra from the low-background facility at KSNL are derived. Part of the parameter space in cross-section versus WIMP-mass is probed and excluded.

Aspects of tests and assessment of filtering materials used for respiratory protection against bioaerosols. Part I: type of active substance, contact time, microorganism species.

PubMed

Majchrzycka, Katarzyna; Gutarowska, Beata; Brochocka, Agnieszka

2010-01-01

This paper presents the results of a study on antimicrobial activity of polymer filter nonwovens produced by needle-punching or melt-blowing with an addition of disinfecting agents. The first part of the paper discusses how the biocidal activity of nonwovens is a function of the active agent added to the nonwovens, the duration of the contact of microorganisms with nonwovens and the type of microorganisms. The types of fibres and disinfecting agents had a considerable effect on the biocidal activity of nonwovens. The biocidal effect of nonwovens increased with the duration of their contact with microorganisms. Fibre activity differed considerably depending on the species of the microorganism. The microorganisms most sensitive to biocidal activity of the active filter nonwoven were S. aureus, M. flavus and E. coli. There were no biocidal effects on spore-forming bacterium B. subtilis.

Electrical contact of wurtzite GaN mircrodisks on p-type GaN template

NASA Astrophysics Data System (ADS)

Tsai, Cheng-Da; Lo, Ikai; Wang, Ying-Chieh; Hsu, Yu-Chi; Shih, Cheng-Hung; Pang, Wen-Yuan; You, Shuo-Ting; Hu, Chia-Hsuan; Chou, Mitch M. C.; Yang, Chen-Chi; Lin, Yu-Chiao

2015-03-01

We developed a back processing to fabricate a secure electrical contact of wurtzite GaN microdisk on a transparent p-type GaN template with the orientation, [10-10]disk // [10-10]template. GaN microdisks were grown on LiAlO2 substrate by using plasma-assisted molecular beam epitaxy. In the further study, we analyzed the TEM specimen of a sample with annealed GaN microdisk/p-typed GaN template by selection area diffraction (SAD) to confirm the alignment of the microdisks with the template at the interface. From the I-V measurements performed on the samples, we obtained a threshold voltage of ~ 5.9 V for the current passing through the GaN microdisks with a resistance of ~ 45 K Ω. The electrical contact can be applied to the nanometer-scaled GaN light-emitting diode.

Current knowledge on biomarkers for contact sensitization and allergic contact dermatitis.

PubMed

Koppes, Sjors A; Engebretsen, Kristiane A; Agner, Tove; Angelova-Fischer, Irena; Berents, Teresa; Brandner, Johanna; Brans, Richard; Clausen, Maja-Lisa; Hummler, Edith; Jakasa, Ivone; Jurakić-Tončic, Ružica; John, Swen M; Khnykin, Denis; Molin, Sonja; Holm, Jan O; Suomela, Sari; Thierse, Hermann-Josef; Kezic, Sanja; Martin, Stefan F; Thyssen, Jacob P

2017-07-01

Contact sensitization is common and affects up to 20% of the general population. The clinical manifestation of contact sensitization is allergic contact dermatitis. This is a clinical expression that is sometimes difficult to distinguish from other types of dermatitis, for example irritant and atopic dermatitis. Several studies have examined the pathogenesis and severity of allergic contact dermatitis by measuring the absence or presence of various biomarkers. In this review, we provide a non-systematic overview of biomarkers that have been studied in allergic contact dermatitis. These include genetic variations and mutations, inflammatory mediators, alarmins, proteases, immunoproteomics, lipids, natural moisturizing factors, tight junctions, and antimicrobial peptides. We conclude that, despite the enormous amount of data, convincing specific biomarkers for allergic contact dermatitis are yet to be described. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Newborns' temperature submitted to radiant heat and to the Top Maternal device at birth.

PubMed

Albuquerque, Rosemeire Sartori de; Mariani, Corintio; Bersusa, Ana Aparecida Sanches; Dias, Vanessa Macedo; Silva, Maria Izabel Mota da

2016-08-08

to compare the axillar temperatures of newborns that are put immediately after birth in skin-to-skin contact under the Top Maternal device, as compared to those in a radiant heat crib. comparatives observational study of the case-control type about temperature of 60 babies born at the Obstetric Center and Normal Delivery Center of a public hospital of the municipality of Sao Paulo, being them: 29 receiving assistance in heated crib and 31 in skin-to skin contact, shielded by a cotton tissue placed on mother's thorax, called Top Maternal. the temperature of the babies of the skin-to-skin contact group presented higher values in a larger share of the time measures verified, as compared to those that were placed in radiant heat crib, independently from the place of birth. Differences between the two groups were not statistically significant. the study contributes to generate new knowledge, supporting the idea of keeping babies with their mothers immediately after birth protected with the Maternal Top, without harming their wellbeing, as it keeps the axillar temperature in recommendable levels. comparar a temperatura axilar dos recém-nascidos acomodados - imediatamente após o nascimento - em contato pele a pele, sob o Top Maternal, em berço de calor radiante. estudo comparativo observacional do tipo Caso-Controle sobre a temperatura de 60 bebês nascidos no Centro Obstétrico e Centro de Parto Normal de um hospital público do município de São Paulo, sendo: 29 assistidos em berço aquecido e 31 em contato pele a pele, protegidos por uma malha de algodão colocada sobre o tórax da mãe, denominada Top Maternal. a temperatura dos bebês do grupo de contato pele a pele teve maior valor na maioria dos tempos verificados comparada à dos que foram colocados em berço de calor radiante, independentemente do local de nascimento. A diferença entre os grupos não foi estatisticamente significante. o estudo contribui com a geração de um novo conhecimento que sustenta a manutenção dos bebês com suas mães imediatamente após o nascimento por meio do contato pele a pele protegidos pelo Top Maternal, sem prejuízos ao seu bem-estar, uma vez que a temperatura axilar se manteve em níveis recomendáveis. comparar la temperatura axilar de los recién nacidos (Rn) acomodados, inmediatamente después del nacimiento, en contacto piel con piel, bajo el Top Maternal, en cuna de calor radiante. estudio comparativo observacional del tipo Caso Control sobre la temperatura de 60 bebés nacidos en el Centro Obstétrico y Centro de Parto Normal de un hospital público del municipio de Sao Paulo, siendo: 29 asistidos en cuna calentada y 31 en contacto piel con piel, protegidos por un tejido de algodón colocado sobre el tórax de la madre, denominado Top Maternal. la temperatura de los bebés del grupo de contacto piel con piel fue más alta en la mayoría de los tiempos verificados, ello comparado con los que fueron colocados en cuna de calor radiante, independientemente del local de nacimiento. La diferencia entre los grupos no fue estadísticamente significativa. el estudio contribuye con la generación de un nuevo conocimiento que sustenta que se debe mantener a los bebés con sus madres inmediatamente después del nacimiento por medio del contacto piel con piel protegidos por el Top Maternal, sin perjuicios a su bienestar, una vez que la temperatura axilar se mantuvo en niveles recomendables.

Oscillations of Accretion Disks in Cataclysmic Variable Stars

NASA Astrophysics Data System (ADS)

Osaki, Y.

2013-12-01

The disk instability model for the outbursts of dwarf novae is reviewed, with particular attention given to the superoutburst of SU UMa stars. Two intrinsic instabilities in accretion disks of dwarf novae are known; the thermal instability and the tidal instability. The thermal-tidal instability model (abbreviated the TTI model), which combines these two instabilities, was first proposed in 1989 by Osaki (1989) to explain the superoutburst phenomenon of SU UMa stars. Recent Kepler observations of one SU UMa star, V1504 Cyg, have dramatically demonstrated that the superoutburst phenomenon of the SU UMa stars is explained by the thermal-tidal instability model.

Sequential ultrasound-microwave assisted acid extraction (UMAE) of pectin from pomelo peels.

PubMed

Liew, Shan Qin; Ngoh, Gek Cheng; Yusoff, Rozita; Teoh, Wen Hui

2016-12-01

This study aims to optimize sequential ultrasound-microwave assisted extraction (UMAE) on pomelo peel using citric acid. The effects of pH, sonication time, microwave power and irradiation time on the yield and the degree of esterification (DE) of pectin were investigated. Under optimized conditions of pH 1.80, 27.52min sonication followed by 6.40min microwave irradiation at 643.44W, the yield and the DE value of pectin obtained was respectively at 38.00% and 56.88%. Based upon optimized UMAE condition, the pectin from microwave-ultrasound assisted extraction (MUAE), ultrasound assisted extraction (UAE) and microwave assisted extraction (MAE) were studied. The yield of pectin adopting the UMAE was higher than all other techniques in the order of UMAE>MUAE>MAE>UAE. The pectin's galacturonic acid content obtained from combined extraction technique is higher than that obtained from sole extraction technique and the pectin gel produced from various techniques exhibited a pseudoplastic behaviour. The morphological structures of pectin extracted from MUAE and MAE closely resemble each other. The extracted pectin from UMAE with smaller and more regular surface differs greatly from that of UAE. This has substantiated the highest pectin yield of 36.33% from UMAE and further signified their compatibility and potentiality in pectin extraction. Copyright © 2016 Elsevier B.V. All rights reserved.

Disease Risk Mitigation: The Equivalence of Two Selective Mixing Strategies on Aggregate Contact Patterns & Resulting Epidemic Spread☆

PubMed Central

Morin, Benjamin R; Perrings, Charles; Levin, Simon; Kinzig, Ann

2014-01-01

The personal choices affecting the transmission of infectious diseases include the number of contacts an individual makes, and the risk-characteristics of those contacts. We consider whether these different choices have distinct implications for the course of an epidemic. We also consider whether choosing contact mitigation (how much to mix) and affinity mitigation (with whom to mix) strategies together has different epidemiological effects than choosing each separately. We use a set of differential equation compartmental models of the spread of disease, coupled with a model of selective mixing. We assess the consequences of varying contact or affinity mitigation as a response to disease risk. We do this by comparing disease incidence and dynamics under varying contact volume, contact type, and both combined across several different disease models. Specifically, we construct a change of variables that allows one to transition from contact mitigation to affinity mitigation, and vice versa. In the absence of asymptomatic infection we find no difference in the epidemiological impacts of the two forms of disease risk mitigation. Furthermore, since models that include both mitigation strategies are under-determined, varying both results in no outcome that could not be reached by choosing either separately. Which strategy is actually chosen then depends not on their epidemiological consequences, but on the relative cost of reducing contact volume versus altering contact type. Although there is no fundamental epidemiological difference between the two forms of mitigation, the social cost of alternative strategies can be very different. From a social perspective, therefore, whether one strategy should be promoted over another depends on economic not epidemiological factors. PMID:25150459

Disease risk mitigation: the equivalence of two selective mixing strategies on aggregate contact patterns and resulting epidemic spread.

PubMed

Morin, Benjamin R; Perrings, Charles; Levin, Simon; Kinzig, Ann

2014-12-21

The personal choices affecting the transmission of infectious diseases include the number of contacts an individual makes, and the risk-characteristics of those contacts. We consider whether these different choices have distinct implications for the course of an epidemic. We also consider whether choosing contact mitigation (how much to mix) and affinity mitigation (with whom to mix) strategies together has different epidemiological effects than choosing each separately. We use a set of differential equation compartmental models of the spread of disease, coupled with a model of selective mixing. We assess the consequences of varying contact or affinity mitigation as a response to disease risk. We do this by comparing disease incidence and dynamics under varying contact volume, contact type, and both combined across several different disease models. Specifically, we construct a change of variables that allows one to transition from contact mitigation to affinity mitigation, and vice versa. In the absence of asymptomatic infection we find no difference in the epidemiological impacts of the two forms of disease risk mitigation. Furthermore, since models that include both mitigation strategies are underdetermined, varying both results in no outcome that could not be reached by choosing either separately. Which strategy is actually chosen then depends not on their epidemiological consequences, but on the relative cost of reducing contact volume versus altering contact type. Although there is no fundamental epidemiological difference between the two forms of mitigation, the social cost of alternative strategies can be very different. From a social perspective, therefore, whether one strategy should be promoted over another depends on economic not epidemiological factors. Copyright © 2014 Elsevier Ltd. All rights reserved.

Higher parental occupational social contact is associated with a reduced risk of incident pediatric type 1 diabetes: Mediation through molecular enteroviral indices

PubMed Central

Pezic, Angela; Cameron, Fergus J.; Rodda, Christine; Kemp, Andrew S.; Carlin, John B.; Hyoty, Heikki; Sioofy-Khojine, Amirbabak; Dwyer, Terence; Ellis, Justine A.; Craig, Maria E.

2018-01-01

We aimed to examine the association between parental occupational social contact and hygiene factors on type 1 diabetes (T1D) risk and possible mediation of these effects through child enteroviral infection. We interviewed 333 incident T1D cases and 660 controls from 2008–2011 in Melbourne, Australia. Enteroviral indices (ribonucleic acid by reverse transcription polymerase chain reaction and Coxsackie B virus antibody levels) in peripheral blood were measured in nested case control samples. Parent occupational social contact was assessed by the number of well or sick children, adults or animals contacted daily through work. Higher parental occupational social contact was strongly associated with reduced T1D risk with evidence of dose response (contact with the well or sick score, Adjusted odds ratio (AOR) per category: 0.73 (95% Confidence Interval (CI): 0.66, 0.81); P<0.001 or AOR 0.63 (95% CI: 0.53, 0.75); P<0.001) respectively). Nine of the ten parental social contact indices, were significant mediated through one or more enteroviral indices. The strength of association between enterovirus presence and T1D onset increased with child age (1.2 fold increase per year; P = 0.05). Lower child hand hygiene enhanced the adverse effect of low parental occupational contact with the sick; Synergy Index 5.16 (95% CI: 3.61, 7.36). The interaction between hand washing and parental occupational contact is more consistent with protection against parental enteroviral shedding than the sharing of a protective infectious agent or microbiome. PMID:29664909

Higher parental occupational social contact is associated with a reduced risk of incident pediatric type 1 diabetes: Mediation through molecular enteroviral indices.

PubMed

Ponsonby, Anne-Louise; Pezic, Angela; Cameron, Fergus J; Rodda, Christine; Kemp, Andrew S; Carlin, John B; Hyoty, Heikki; Sioofy-Khojine, Amirbabak; Dwyer, Terence; Ellis, Justine A; Craig, Maria E

2018-01-01

We aimed to examine the association between parental occupational social contact and hygiene factors on type 1 diabetes (T1D) risk and possible mediation of these effects through child enteroviral infection. We interviewed 333 incident T1D cases and 660 controls from 2008-2011 in Melbourne, Australia. Enteroviral indices (ribonucleic acid by reverse transcription polymerase chain reaction and Coxsackie B virus antibody levels) in peripheral blood were measured in nested case control samples. Parent occupational social contact was assessed by the number of well or sick children, adults or animals contacted daily through work. Higher parental occupational social contact was strongly associated with reduced T1D risk with evidence of dose response (contact with the well or sick score, Adjusted odds ratio (AOR) per category: 0.73 (95% Confidence Interval (CI): 0.66, 0.81); P<0.001 or AOR 0.63 (95% CI: 0.53, 0.75); P<0.001) respectively). Nine of the ten parental social contact indices, were significant mediated through one or more enteroviral indices. The strength of association between enterovirus presence and T1D onset increased with child age (1.2 fold increase per year; P = 0.05). Lower child hand hygiene enhanced the adverse effect of low parental occupational contact with the sick; Synergy Index 5.16 (95% CI: 3.61, 7.36). The interaction between hand washing and parental occupational contact is more consistent with protection against parental enteroviral shedding than the sharing of a protective infectious agent or microbiome.

Bacterial and fungal biofilm formation on contact lenses and their susceptibility to lens care solutions.

PubMed

Kackar, Siddharth; Suman, Ethel; Kotian, M Shashidhar

2017-01-01

Microbial biofilm formation on contact lenses and lens storage cases may be a risk factor for contact lens-associated corneal infections. Various types of contact lens care solutions are used to reduce microbial growths on lenses. The present study aimed at comparing the growths of biofilms on the different contact lenses and lens cases. The study also aimed at determining the effect of lens care solutions and bacteriophage on these biofilms. One type of hard lens and two types of soft lenses were used for the study. The organisms used were Staphylococcus aureus ATCC 25923, Pseudomonas aeruginosa ATCC 27853, Candida albicans ATCC 60193 and Escherichia coli ATCC 25922. Biofilm production was performed by modified O'Toole and Kolter method and effect of lens cleaning solutions and a crude coliphage on biofilms was also studied. Results were visualised using scanning electron microscopy and quantitated by colony counting method and spectrophotometric measurement of optical density (OD). Statistical analysis was done by SPSS 11.5, Kruskal-Wallis test and Chi-square test. Soft lens cleaning solutions had a significant inhibitory effect (P = 0.020) on biofilm formation on soft lenses and also lens cases (P < 0.001). Soft lens cleaning solution 2 was more efficient than solution 1. However, no such inhibitory effect was observed with regard to hard lens cleaning solution, but for a significant reduction in the OD values (P < 0.001). There was no significant inhibitory effect by bacteriophages. This study showed the importance of selecting the appropriate lens cleaning solution to prevent biofilm production on contact lenses.

Ultrastructure of the central subnucleus of the nucleus tractus solitarii and the esophageal afferent terminals in the rat.

PubMed

Hayakawa, Tetsu; Takanaga, Akinori; Tanaka, Koichi; Maeda, Seishi; Seki, Makoto

2003-03-01

The central subnucleus of the nucleus tractus solitarii (ceNTS) receives afferent projections from the esophageal wall and projects to the nucleus ambiguus, thus serving as a relay nucleus for peristalsis of the esophagus. Here we examine the synaptic organization of the ceNTS, and its esophageal afferents by using transganglionic anterograde transport of cholera toxin-conjugated horseradish peroxidase (CT-HRP). When CT-HRP was injected into the subdiaphragmatic esophagus, many anterogradely labeled terminals were found only in the ceNTS. The ceNTS was composed of round or oval-shaped, small neurons (14.7x8.7 micro m) containing sparse organelles and an irregularly shaped nucleus. The average number of axosomatic terminals was only 1.3 per section cut through the nucleolus. Most of them (92%) contained round vesicles and formed asymmetric synaptic contacts (Gray's type I), and a few (8%) contained pleomorphic vesicles and formed symmetric synaptic contacts (Gray's type II). All anterogradely labeled terminals contacted dendrites but not the neuronal somata. The labeled terminals were large (2.55+/-0.07 micro m) and exclusively Gray's type I. More than half of them (60%) contacted small dendrites (less than 1 micro m in diameter), and contained dense-cored vesicles. More than 40% of the labeled terminals contacted two to four dendrites, thus forming a synaptic glomerulus. Sometimes a labeled terminal that contacted an unlabeled terminal by an adherent junction was found within the glomerulus. The large terminals and these complex synaptic relations appeared to characterize the esophageal afferent projections in the ceNTS.

Atomic force microscopy and scanning electron microscopy analysis of daily disposable limbal ring contact lenses.

PubMed

Lorenz, Kathrine Osborn; Kakkassery, Joseph; Boree, Danielle; Pinto, David

2014-09-01

Limbal ring (also known as 'circle') contact lenses are becoming increasingly popular, especially in Asian markets because of their eye-enhancing effects. The pigment particles that give the eye-enhancing effects of these lenses can be found on the front or back surface of the contact lens or 'enclosed' within the lens matrix. The purpose of this research was to evaluate the pigment location and surface roughness of seven types of 'circle' contact lenses. Scanning electron microscopic (SEM) analysis was performed using a variable pressure Hitachi S3400N instrument to discern the placement of lens pigments. Atomic force microscopy (Dimension Icon AFM from Bruker Nano) was used to determine the surface roughness of the pigmented regions of the contact lenses. Atomic force microscopic analysis was performed in fluid phase under contact mode using a Sharp Nitride Lever probe (SNL-10) with a spring constant of 0.06 N/m. Root mean square (RMS) roughness values were analysed using a generalised linear mixed model with a log-normal distribution. Least square means and their corresponding 95% confidence intervals were estimated for each brand, location and pigment combination. SEM cross-sectional images at 500× and 2,000× magnification showed pigment on the surface of six of the seven lens types tested. The mean depth of pigment for 1-DAY ACUVUE DEFINE (1DAD) lenses was 8.1 μm below the surface of the lens, while the remaining lens types tested had pigment particles on the front or back surface. Results of the atomic force microscopic analysis indicated that 1DAD lenses had significantly lower root mean square roughness values in the pigmented area of the lens than the other lens types tested. SEM and AFM analysis revealed pigment on the surface of the lens for all types tested with the exception of 1DAD. Further research is required to determine if the difference in pigment location influences on-eye performance. © 2014 The Authors. Clinical and Experimental Optometry © 2014 Optometrists Association Australia.

Atomic force microscopy and scanning electron microscopy analysis of daily disposable limbal ring contact lenses

PubMed Central

Lorenz, Kathrine Osborn; Kakkassery, Joseph; Boree, Danielle; Pinto, David

2014-01-01

Background Limbal ring (also known as ‘circle’) contact lenses are becoming increasingly popular, especially in Asian markets because of their eye-enhancing effects. The pigment particles that give the eye-enhancing effects of these lenses can be found on the front or back surface of the contact lens or ‘enclosed’ within the lens matrix. The purpose of this research was to evaluate the pigment location and surface roughness of seven types of ‘circle’ contact lenses. Methods Scanning electron microscopic (SEM) analysis was performed using a variable pressure Hitachi S3400N instrument to discern the placement of lens pigments. Atomic force microscopy (Dimension Icon AFM from Bruker Nano) was used to determine the surface roughness of the pigmented regions of the contact lenses. Atomic force microscopic analysis was performed in fluid phase under contact mode using a Sharp Nitride Lever probe (SNL-10) with a spring constant of 0.06 N/m. Root mean square (RMS) roughness values were analysed using a generalised linear mixed model with a log-normal distribution. Least square means and their corresponding 95% confidence intervals were estimated for each brand, location and pigment combination. Results SEM cross-sectional images at 500× and 2,000× magnification showed pigment on the surface of six of the seven lens types tested. The mean depth of pigment for 1-DAY ACUVUE DEFINE (1DAD) lenses was 8.1 μm below the surface of the lens, while the remaining lens types tested had pigment particles on the front or back surface. Results of the atomic force microscopic analysis indicated that 1DAD lenses had significantly lower root mean square roughness values in the pigmented area of the lens than the other lens types tested. Conclusions SEM and AFM analysis revealed pigment on the surface of the lens for all types tested with the exception of 1DAD. Further research is required to determine if the difference in pigment location influences on-eye performance. PMID:24689948

The zero-bias anomaly of point contacts with ferromagnetic Ni and with the heavy-fermion antiferromagnet CeAl2

NASA Astrophysics Data System (ADS)

Gloos, Kurt; Huupponen, Jouko

2010-01-01

We have investigated spear-anvil type point-contacts between ferromagnetic nickel as well as the heavy-fermion antiferromagnet CeAl2 and various simple metals (Cu, Ta, Nb). Contacts with small resistance usually showed electron-phonon scattering, Andreev reflection in case of superconducting counter-electrodes, as well as anomalies due to magnetic ordering. With increasing contact resistance (decreasing contact size) a zero-bias anomaly appeared in both Ni and CeAl2 contacts. It is conventionally attributed to resonant scattering at two-level systems or at magnetic impurities (Kondo effect). At contacts of ~ 1 nm diameter it suppressed completely all other spectral features. We discuss whether those mechanisms are relevant here and what alternatives there might be.

An Interview Study of Inter-Cultural Contact and Its Role in Language Learning in a Foreign Language Environment

ERIC Educational Resources Information Center

Kormos, Judit; Csizer, Kata

2007-01-01

The research reported in this paper investigates what types of inter-cultural contact Hungarian schoolchildren have, what kind of language-related attitudes they can give account of and how they see the role of contact situations in affecting their attitudinal and motivational dispositions towards the L2, the L2 speaking communities and the…

An Analytical Solution and Numerical Modeling Study of Gas Hydrate Saturation Effects on Porosity and Permeability of Porous Media

NASA Astrophysics Data System (ADS)

Zerpa, L.; Gao, F.; Wang, S.

2017-12-01

There are two major types of natural gas hydrate distributions in porous media: pore filling and contact cementing. The difference between these two distribution types is related to hydrate nucleation and growth processes. In the pore filling distribution, hydrate nucleates from a gas-dissolved aqueous phase at the grain boundary and grows away from grain contacts and surfaces into the pore space. In the contact cementing distribution, hydrate nucleates and grows at the gas-water interface and at intergranular contacts. Previous attempts to correlate changes on porosity and permeability during hydrate formation/dissociation were based on the length difference between the pore body and pore throat, and only considered contact cementing hydrate distribution. This work consists of a study of mathematical models of permeability and porosity as a function of gas hydrate saturation during formation and dissociation of gas hydrates in porous media. In this work, first we derive the permeability equation for the pore filling hydrate deposition as a function of hydrate saturation. Then, a more comprehensive model considering both types of gas hydrate deposition is developed to represent changes in permeability and porosity during hydrate formation and dissociation. This resulted in a model that combines pore filling and contact cementing deposition types in the same reservoir. Finally, the TOUGH+Hydrate numerical reservoir simulator was modified to include these models to analyze the response of production and saturation during a depressurization process, considering different combinations of pore filling and contact cementing hydrate distributions. The empirical exponent used in the permeability adjustment factor model influences both production profile and saturation results. This empirical factor describes the permeability dependence to changes in porosity caused by solid phase formation in the porous medium. The use of the permeability exponent decreases the permeability of the system for a given hydrate saturation, which affects the hydraulic performance of the system. However, from published experimental work, there is only a rough estimation of this permeability exponent. This factor could be represented with an empirical equation if more laboratory and field data becomes available.

Some economic aspects of recreational injuries.

PubMed

Arundel, J T

1974-06-01

This paper deals with some basic features of accidents in recreation and will attempt to throw some light on their economic consequences. Let us examine sport as one aspect of recreation. As Williams (1973) put it, "Sport is a phenomenon of simple definition, but with well recognised features. It is essentially recreational, essentially physical, frequently competitive and always contrived." The number and type of participants has increased, along with the range of activities available. Classifications of sport, at best, are arbitrary but nevertheless are useful for analysis. These divisions may be land/air/water types; indoor/outdoor; team/individual; body contact/non-contact/vehicular; amateur/professional. Sports injuries are of two types, intrinsic or self-inflicted (Williams, 1973) and extrinsic. Intrinsic injuries refer to those as a result of over-use (leading, for example, to stress fractures) and to specific incidents not involving outside agents. Extrinsic injuries are caused by contact with external objects and form the bulk of injuries sustained in body-contact, vehicular (horses, cars, skis) and environmental-type sports. Extrinsic injuries are generally more severe because greater forces and velocities are involved. Appendix 1 lists the main sporting activities according to location of sport; individual or team participation; likelihood of extensive body contact; and professional status. Professional players not only suffer loss of earning capacity but may reflect a bad investment for an entrepreneur or reduce spectator attendance and gate taking. It is apparent that team sports, having substantial body contact, face a higher risk of moderate to serious injury than do individual, non-contact sports, although major injuries can be sustained in the latter, for example, sprains and dislocations in athletics, golf, tennis, etc. Other sports must be classed as dangerous because of the nature of competition, for example, motor racing and flying. These particulars were collated during a survey on economic aspects of sport undertaken by the author in 1971-72 in Queensland. Some indication of the proportion of sport participants in the total Queensland population is given in Table 1. Copyright © 1974 Australian Physiotherapy Association. Published by . All rights reserved.

Contact Us

Science.gov Websites

Other types of pesticides Disponible en español Contact Us NPIC staff Call us (toll free): 800-858-7378 We have trained pesticide specialists available to help you free of charge from 8:00am to 12:00pm

Rolling contact fatigue : a comprehensive review.

DOT National Transportation Integrated Search

2011-11-01

"Rolling contact fatigue (RCF) is a pervasive and insidious problem on all types of railway systems. Although it is a dominant cause of maintenance and replacements on heavy haul rail lines, it is also a significant economic and safety challenge for ...

The Extended Contact Hypothesis: A Meta-Analysis on 20 Years of Research.

PubMed

Zhou, Shelly; Page-Gould, Elizabeth; Aron, Arthur; Moyer, Anne; Hewstone, Miles

2018-04-01

According to the extended contact hypothesis, knowing that in-group members have cross-group friends improves attitudes toward this out-group. This meta-analysis covers the 20 years of research that currently exists on the extended contact hypothesis, and consists of 248 effect sizes from 115 studies. The aggregate relationship between extended contact and intergroup attitudes was r = .25, 95% confidence interval (CI) = [.22, .27], which reduced to r = .17, 95% CI = [.14, .19] after removing direct friendship's contribution; these results suggest that extended contact's hypothesized relationship to intergroup attitudes is small-to-medium and exists independently of direct friendship. This relationship was larger when extended contact was perceived versus actual, highlighting the importance of perception in extended contact. Current results on extended contact mostly resembled their direct friendship counterparts, suggesting similarity between these contact types. These unique insights about extended contact and its relationship with direct friendship should enrich and spur growth within this literature.

An electric contact method to measure contact state between stator and rotor in a traveling wave ultrasonic motor.

PubMed

Qu, Jianjun; Zhou, Tieying

2003-09-01

Performances of ultrasonic motor (USM) depend considerably on contact state between stator and rotor. To measure the contact state in a traveling wave ultrasonic motor (TWUSM), a special test method is necessary. This paper develops a new method named electric contact method to measure contact state of stator and rotor in traveling wave type USM. The effects of pre-load and exciting voltage (amplitude) of stator on contact state between stator and rotor are studied with this method. By a simulating tester of friction properties of TWUSM, the variations of stalling torque and no-load speed against the pre-load and the exciting voltage have been measured. The relative contact length that describes the contact characteristic of stator and rotor is proposed. The relation between the properties of TWUSM and the contact state of stator and rotor are presented. Additionally, according to a theoretical contact model of stator and rotor in TWUSM, the contact lengths at given conditions are calculated and compared with the experimental results.

Restoration of the contact surface in FORCE-type centred schemes I: Homogeneous two-dimensional shallow water equations

NASA Astrophysics Data System (ADS)

Canestrelli, Alberto; Toro, Eleuterio F.

2012-10-01

Recently, the FORCE centred scheme for conservative hyperbolic multi-dimensional systems has been introduced in [34] and has been applied to Euler and relativistic MHD equations, solved on unstructured meshes. In this work we propose a modification of the FORCE scheme, named FORCE-Contact, that provides improved resolution of contact and shear waves. This paper presents the technique in full detail as applied to the two-dimensional homogeneous shallow water equations. The improvements due to the new method are particularly evident when an additional equation is solved for a tracer, since the modified scheme exactly resolves isolated and steady contact discontinuities. The improvement is considerable also for slowly moving contact discontinuities, for shear waves and for steady states in meandering channels. For these types of flow fields, the numerical results provided by the new FORCE-Contact scheme are comparable with, and sometimes better than, the results obtained from upwind schemes, such as Roes scheme for example. In a companion paper, a similar approach to restoring the missing contact wave and preserving well-balanced properties for non-conservative one- and two-layer shallow water equations is introduced. However, the procedure is general and it is in principle applicable to other multidimensional hyperbolic systems in conservative and non-conservative form, such as the Euler equations for compressible gas dynamics.

Influence of Asymmetric Contact Form on Contact Resistance and Schottky Barrier, and Corresponding Applications of Diode.

PubMed

Zhao, Yudan; Xiao, Xiaoyang; Huo, Yujia; Wang, Yingcheng; Zhang, Tianfu; Jiang, Kaili; Wang, Jiaping; Fan, Shoushan; Li, Qunqing

2017-06-07

We have fabricated carbon nanotube and MoS 2 field-effect transistors with asymmetric contact forms of source-drain electrodes, from which we found the current directionality of the devices and different contact resistances under the two current directions. By designing various structures, we can conclude that the asymmetric electrical performance was caused by the difference in the effective Schottky barrier height (Φ SB ) caused by the different contact forms. A detailed temperature-dependent study was used to extract and compare the Φ SB for both contact forms of CNT and MoS 2 devices; we found that the Φ SB for the metal-on-semiconductor form was much lower than that of the semiconductor-on-metal form and is suitable for all p-type, n-type, or ambipolar semiconductors. This conclusion is meaningful with respect to the design and application of nanomaterial electronic devices. Additionally, using the difference in barrier height caused by the contact forms, we have also proposed and fabricated Schottky barrier diodes with a current ratio up to 10 4 ; rectifying circuits consisting of these diodes were able to work in a wide frequency range. This design avoided the use of complex chemical doping or heterojunction methods to achieve fundamental diodes that are relatively simple and use only a single material; these may be suitable for future application in nanoelectronic radio frequency or integrated circuits.

Colonisation with toxigenic Corynebacterium diphtheriae in a Scottish burns patient, June 2015.

PubMed

Deshpande, Ashutosh; Inkster, Teresa; Hamilton, Kate; Litt, David; Fry, Norman; Kennedy, Iain T R; Shookhye-Dickson, Jacqueline; Hill, Robert L R

2015-01-01

On 12 June 2015, Corynebacterium diphtheriae was identified in a skin swab from a burns patient in Scotland. The isolate was confirmed to be genotypically and phenotypically toxigenic. Multilocus sequence typing of three patient isolates yielded sequence type ST 125. The patient was clinically well. We summarise findings of this case, and results of close contact identification and screening: 12 family and close contacts and 32 hospital staff have been found negative for C. diphtheriae.

Evaluation of Three Swabbing Devices for Detection of Listeria monocytogenes on Different Types of Food Contact Surfaces

PubMed Central

Lahou, Evy; Uyttendaele, Mieke

2014-01-01

Listeria monocytogenes can adhere to different types of food contact surfaces within a food processing environment. Therefore, environmental sampling devices should be capable of detecting unacceptable contamination. In this study, a sponge-stick, foam spatula and an environmental swab were evaluated on their ability to detect low concentrations of L. monocytogenes on different types of food contact surfaces. A cocktail of four L. monocytogenes serotypes was inoculated with a concentration of 100 CFU/250 cm2 onto stainless steel (SS), high density polyethylene (HDPE) and rubber surfaces in a 250 cm2 area. Immediately after inoculation and after 1 h exposure, the surfaces were swabbed with the different swabbing devices. The results of the study show only minor differences in the ability of the swabbing devices to detect L. monocytogenes. All devices were capable to detect the contamination immediately after inoculation. However, when the surfaces were allowed to air-dry for 1 h, L. monocytogenes was undetected in 11.1% of the samples (n = 27) with the sponge stick, in 7.4% of the samples (n = 27) with the foam spatula and in 3.7% of the samples (n = 27) with the environmental swab, especially on SS surfaces. The detection ability of the different devices for L. monocytogenes can be concluded to be rather high on different types of food contact surfaces. PMID:24406663

Evolutionarily conserved regions and hydrophobic contacts at the superfamily level: The case of the fold-type I, pyridoxal-5′-phosphate-dependent enzymes

PubMed Central

Paiardini, Alessandro; Bossa, Francesco; Pascarella, Stefano

2004-01-01

The wealth of biological information provided by structural and genomic projects opens new prospects of understanding life and evolution at the molecular level. In this work, it is shown how computational approaches can be exploited to pinpoint protein structural features that remain invariant upon long evolutionary periods in the fold-type I, PLP-dependent enzymes. A nonredundant set of 23 superposed crystallographic structures belonging to this superfamily was built. Members of this family typically display high-structural conservation despite low-sequence identity. For each structure, a multiple-sequence alignment of orthologous sequences was obtained, and the 23 alignments were merged using the structural information to obtain a comprehensive multiple alignment of 921 sequences of fold-type I enzymes. The structurally conserved regions (SCRs), the evolutionarily conserved residues, and the conserved hydrophobic contacts (CHCs) were extracted from this data set, using both sequence and structural information. The results of this study identified a structural pattern of hydrophobic contacts shared by all of the superfamily members of fold-type I enzymes and involved in native interactions. This profile highlights the presence of a nucleus for this fold, in which residues participating in the most conserved native interactions exhibit preferential evolutionary conservation, that correlates significantly (r = 0.70) with the extent of mean hydrophobic contact value of their apolar fraction. PMID:15498941

The impact of vaccine success and awareness on epidemic dynamics

NASA Astrophysics Data System (ADS)

Juang, Jonq; Liang, Yu-Hao

2016-11-01

The role of vaccine success is introduced into an epidemic spreading model consisting of three states: susceptible, infectious, and vaccinated. Moreover, the effect of three types, namely, contact, local, and global, of infection awareness and immunization awareness is also taken into consideration. The model generalizes those considered in Pastor-Satorras and Vespignani [Phys. Rev. E 63, 066117 (2001)], Pastor-Satorras and Vespignani [Phys. Rev. E 65, 036104 (2002)], Moreno et al. [Eur. Phys. J. B 26, 521-529 (2002)], Wu et al. [Chaos 22, 013101 (2012)], and Wu et al. [Chaos 24, 023108 (2014)]. Our main results contain the following. First, the epidemic threshold is explicitly obtained. In particular, we show that, for any initial conditions, the epidemic eventually dies out regardless of what other factors are whenever some type of immunization awareness is considered, and vaccination has a perfect success. Moreover, the threshold is independent of the global type of awareness. Second, we compare the effect of contact and local types of awareness on the epidemic thresholds between heterogeneous networks and homogeneous networks. Specifically, we find that the epidemic threshold for the homogeneous network can be lower than that of the heterogeneous network in an intermediate regime for intensity of contact infection awareness while it is higher otherwise. In summary, our results highlight the important and crucial roles of both vaccine success and contact infection awareness on epidemic dynamics.

Contact reflectivity effects on thin p-clad InGaAs single quantum-well lasers

NASA Astrophysics Data System (ADS)

Wu, C. H.; Zory, P. S.; Emanuel, M. A.

1994-12-01

Thin p-clad InGaAs quantum-well (QW) lasers with either Au or Ni as the p-contact metal have been fabricated. Due to reduced contact reflectivity, the Ni contact lasers have significantly higher threshold currents and lower slope efficiencies than the Au contact lasers. In addition, operating wavelength differences greater than 50 nm are observed for cavity lengths between 250 and 700 microns, with large wavelength jumps occurring at shorter and longer cavity lengths. The measured wavelength effects are explained by incorporating the optical mode loss difference between the two laser types into quantum-well laser theory.

A contact layer element for large deformations

NASA Astrophysics Data System (ADS)

Weißenfels, C.; Wriggers, P.

2015-05-01

In many contact situations the material behavior of one contact member strongly influences the force acting between the two bodies. Unfortunately standard friction models cannot reproduce all of these material effects at the contact layer and often continuum interface elements are used instead. These elements are intrinsically tied to the fixed grid and hence cannot be used in large sliding simulations. Due to the shortcomings of the standard contact formulations and of the interface elements a new type of a contact layer element is developed in this work. The advantages of this element are the direct implementation of continuum models into the contact formulation and the application to arbitrary large deformations. Showing a relation between continuum and contact kinematics based on the solid-shell concept the new contact element is at the end a natural extension of the standard contact formulations into 3D. Two examples show that the continuum behavior can be exactly reproduced at the contact surface even in large sliding situations using this contact layer element. For the discretization of the new contact element the Mortar method is chosen exemplary, but it can be combined with all kinds of contact formulations.

Nanoparticle embedded p-type electrodes for GaN-based flip-chip light emitting diodes.

PubMed

Kwak, Joon Seop; Song, J O; Seong, T Y; Kim, B I; Cho, J; Sone, C; Park, Y

2006-11-01

We have investigated high-quality ohmic contacts for flip-chip light emitting diodes using Zn-Ni nanoparticles/Ag schemes. The Zn-Ni nanoparticles/Ag contacts produce specific contact resistances of 10(-5)-10(-6) omegacm2 when annealed at temperatures of 330-530 degrees C for 1 min in air ambient, which are much better than those obtained from the Ag contacts. It is shown that blue InGaN/GaN multi-quantum well light emitting diodes fabricated with the annealed Zn-Ni nanoparticles/Ag contacts give much lower forward-bias voltages at 20 mA compared with those of the multi-quantum well light emitting diodes made with the as-deposited Ag contacts. It is further presented that the multi-quantum well light emitting diodes made with the Zn-Ni nanoparticles/Ag contacts show similar output power compared to those fabricated with the Ag contact layers.

Pseudophakodonesis and corneal endothelial contact: direct observations by high-speed cinematography.

PubMed

Jacobs, P M; Cheng, H; Price, N C

1983-10-01

High-speed cinematography was used to observe the movement of Federov type I lens implants within the anterior chamber. Our measurements suggest that in most patients contact between the lens implant and corneal endothelium does not occur.

Database of amino acid-nucleotide contacts in contacts in DNA-homeodomain protein

NASA Astrophysics Data System (ADS)

Grokhlina, T. I.; Zrelov, P. V.; Ivanov, V. V.; Polozov, R. V.; Chirgadze, Yu. N.; Sivozhelezov, V. S.

2013-09-01

The analysis of amino acid-nucleotide contacts in interfaces of the protein-DNA complexes, intended to find consistencies in the protein-DNA recognition, is a complex problem that requires an analysis of the physicochemical characteristics of these contacts and the positions of the participating amino acids and nucleotides in the chains of the protein and the DNA, respectively, as well as conservatism of these contacts. Thus, those heterogeneous data should be systematized. For this purpose we have developed a database of amino acid-nucleotide contacts ANTPC (Amino acid Nucleotide Type Position Conservation) following the archetypal example of the proteins in the homeodomain family. We show that it can be used to compare and classify the interfaces of the protein-DNA complexes.

Non-smooth Hopf-type bifurcations arising from impact–friction contact events in rotating machinery

PubMed Central

Mora, Karin; Budd, Chris; Glendinning, Paul; Keogh, Patrick

2014-01-01

We analyse the novel dynamics arising in a nonlinear rotor dynamic system by investigating the discontinuity-induced bifurcations corresponding to collisions with the rotor housing (touchdown bearing surface interactions). The simplified Föppl/Jeffcott rotor with clearance and mass unbalance is modelled by a two degree of freedom impact–friction oscillator, as appropriate for a rigid rotor levitated by magnetic bearings. Two types of motion observed in experiments are of interest in this paper: no contact and repeated instantaneous contact. We study how these are affected by damping and stiffness present in the system using analytical and numerical piecewise-smooth dynamical systems methods. By studying the impact map, we show that these types of motion arise at a novel non-smooth Hopf-type bifurcation from a boundary equilibrium bifurcation point for certain parameter values. A local analysis of this bifurcation point allows us a complete understanding of this behaviour in a general setting. The analysis identifies criteria for the existence of such smooth and non-smooth bifurcations, which is an essential step towards achieving reliable and robust controllers that can take compensating action. PMID:25383034

Type-inversion as a working mechanism of high voltage MAPbBr3(Cl)-based halide perovskite solar cells.

PubMed

Kedem, Nir; Kulbak, Michael; Brenner, Thomas M; Hodes, Gary; Cahen, David

2017-02-22

Using several metals with different work functions as solar cell back contact we identify majority carrier type inversion in methylammonium lead bromide (MAPbBr3, without intentional doping) as the basis for the formation of a p-n junction. MAPbBr 3 films deposited on TiO 2 are slightly n-type, whereas in a full device they are strongly p-type. The charge transfer between the metal electrode and the halide perovskite (HaP) film is shown to determine the dominant charge carrier type of the HaP and, thus, also of the final cells. Usage of Pt, Au and Pb as metal electrodes shows the effects of metal work function on minority carrier diffusion length and majority carrier concentration in the HaP, as well as on built-in voltage, band bending, and open circuit voltage (V OC ) within a solar cell. V OC > 1.5 V is demonstrated. The higher the metal WF, the higher the carrier concentration induced in the HaP, as indicated by a narrower space charge region and a smaller minority carrier diffusion length. From the analysis of bias-dependent electron beam-induced currents, the HaP carrier concentrations are estimated to be ∼ 1 × 10 17 cm -3 with Au and 2-3 × 10 18 cm -3 with Pt. A model in which type-inversion stretches across the entire film width implies formation of the p-n junction away from the interface, near the back-contact metal electrode. This work highlights the importance of the contact metal on device performance in that contact engineering can also serve to control the carrier concentration in HaP.

Comparison of adverse events with daily disposable hydrogels and spectacle wear: results from a 12-month prospective clinical trial.

PubMed

Sankaridurg, Padmaja R; Sweeney, Deborah F; Holden, Brien A; Naduvilath, Thomas; Velala, Indira; Gora, Rashmi; Krishnamachary, Murali; Rao, Gullapalli N

2003-12-01

To evaluate the type and incidence of adverse events seen with daily disposable hydrogel contact lens wear compared with a control (spectacle) group over 12 months. Prospective, randomized, observer-masked, comparative clinical trial. Two hundred eighty-one myopes with no prior contact lens wear experience were enrolled from August to December 1996. Subjects were 16 to 35 years old and had refractive errors ranging from a -0.75-diopter (D) sphere to a -6.00-D sphere with a cylinder less than -1.00 D. Each subject was randomly assigned to wear either bilateral disposable hydrogels on a daily disposable wear schedule or spectacles. Type and incidence of adverse events from each group. Adverse events were categorized as serious, significant, and nonsignificant based on the potential to cause vision impairment, severity at event, and level of clinical concern. At baseline, 1.6% of eyes had asymptomatic infiltrates that were nonsignificant. During the study, asymptomatic infiltrates were seen in both contact lens and spectacle groups at 20.5 events versus 11.3 events per 100 eyes per year of wear. No significant events were seen with the spectacle group. With the contact lens group, the type and incidence of significant events per 100 eyes per year of lens wear were corneal peripheral ulcer, 2.5 events; infiltrative keratitis, 1.5 events; and papillary conjunctivitis, 1 event. The incidence of both significant and nonsignificant events was greater with the contact lens group (P<0.05). No serious events (i.e., microbial keratitis) were seen in either group. A greater number of subjects were lost to follow-up or permanently discontinued from the contact lens group relative to the spectacle group (33% vs. 17%, P = 0.002). Lens-related problems such as dryness, discomfort, and difficulty with insertion and removal accounted for 27% of discontinuations from the contact lens group. Poor compliance (40%) was the greatest reason for discontinuations from the spectacle group. No clinically serious events were seen with either group. Only a small percentage of contact lens-wearing eyes presented with significant events, which is promising for daily disposable lens wear. Far more contact lens subjects were lost to follow-up or discontinued. Small, asymptomatic, subepithelial corneal infiltrates of unknown significance were seen in both contact lens- and spectacle-wearing eyes.

N-SCAN: new vibromodulation system for detection and monitoring of cracks and other contact-type defects

NASA Astrophysics Data System (ADS)

Donskoy, Dmitri; Ekimov, Alexander; Luzzato, Emile; Lottiaux, Jean-Louis; Stoupin, Stanislav; Zagrai, Andrei

2003-08-01

In recent years, innovative vibro-modulation technique has been introduced for detection of contact-type interfaces such as cracks, debondings, and delaminations. The technique utilizes the effect of nonlinear interaction of ultrasound and vibrations at the interface of the defect. Vibration varies on the contact area of the interface modulating passing through ultrasonic wave. The modulation manifests itself as additional side-band spectral components with the combination frequencies in the spectrum of the received signal. The presence of these components allows for detection and differentiation of the contact-type defects from other structural and material inhomogeneities. Vibro-modulation technique has been implemented in N-SCAN damage detection system. The system consists of a digital synthesizer, high and low frequency amplifiers, a magnetostrictive shaker, ultrasonic transducers and a PC-based data acquisition/processing station with N-SCAN software. The ability of the system to detect contact-type defects was experimentally verified using specimens of simple and complex geometries made of steel, aluminum, composites and other structural materials. N-SCAN proved to be very effective for nondestructive testing of full-scale structures ranging from 24 foot-long gun barrels to stainless steel pipes used in nuclear power plants. Among advantages of the system are applicability for the wide range of structural materials and for structures with complex geometries, real time data processing, convenient interface for system operation, simplicity of interpretation of results, no need for sensor scanning along structure, onsite inspection of large structures at a fraction of time as compared with conventional techniques. This paper describes the basic principles of nonlinear vibro-modulation NDE technique, some theoretical background for nonlinear interaction and justification of signal processing algorithm. It is also presents examples of practical implementation and application of the technique.

Analysis for Material Behavior of Sabot/Rods During Launch by Finite Element Method

NASA Astrophysics Data System (ADS)

Kim, Jin Bong; Kim, Man Geun

This study has been investigated to predict the deformation and states of stress and strain by axial and lateral acceleration during launch. Because a gun tube is not perfectly straight at its initial state while under gravity loading, the projectile deforms due to the change of contacts points with the flexible gun tube. Numerical simulations were used for gravity loading and the other type is initial shape and gravity loading. The ANSYS engineering analysis code was used to generate a parametric model of the projectile and conduct finite element analyses. Four types of nonlinear material and contact elements were incorporated into the model to account for the plastic deformation and contact between the penetrator, sabot, and tube.

Interictal spike detection comparing subdural and depth electrodes during electrocorticography.

PubMed

Privitera, M D; Quinlan, J G; Yeh, H S

1990-11-01

We compared the ability of subdural and depth electrodes to detect and localize interictal epileptiform discharges (IEDs) in the temporal lobe. Sixteen patients had simultaneous intraoperative recordings with depth and subdural electrodes while undergoing anterior temporal lobe resections under local anesthesia for medically intractable seizures. IEDs that were focal (detected at just 1 or 2 electrode contacts) typically registered at the nearest contact, regardless of type. IEDs that were regional (engaging more than 2 electrode contacts) typically appeared simultaneously at both electrode types. Neither method was better able to indicate whether an IED was mesial or lateral, posterior or anterior. Subdural and depth electrodes seem to provide complementary information on the location of IEDs within the temporal lobe.

Friction Mapping as a Tool for Measuring the Elastohydrodynamic Contact Running-in Process

DTIC Science & Technology

2015-10-01

ARL-TR-7501 ● OCT 2015 US Army Research Laboratory Friction Mapping as a Tool for Measuring the Elastohydrodynamic Contact...Research Laboratory Friction Mapping as a Tool for Measuring the Elastohydrodynamic Contact Running-in Process by Stephen Berkebile Vehicle...YYYY) October 2015 2. REPORT TYPE Final 3. DATES COVERED (From - To) 1 January–30 June 2015 4. TITLE AND SUBTITLE Friction Mapping as a Tool for

Contact electrification induced interfacial reactions and direct electrochemical nanoimprint lithography in n-type gallium arsenate wafer.

PubMed

Zhang, Jie; Zhang, Lin; Wang, Wei; Han, Lianhuan; Jia, Jing-Chun; Tian, Zhao-Wu; Tian, Zhong-Qun; Zhan, Dongping

2017-03-01

Although metal assisted chemical etching (MacEtch) has emerged as a versatile micro-nanofabrication method for semiconductors, the chemical mechanism remains ambiguous in terms of both thermodynamics and kinetics. Here we demonstrate an innovative phenomenon, i.e. , the contact electrification between platinum (Pt) and an n-type gallium arsenide (100) wafer (n-GaAs) can induce interfacial redox reactions. Because of their different work functions, when the Pt electrode comes into contact with n-GaAs, electrons will move from n-GaAs to Pt and form a contact electric field at the Pt/n-GaAs junction until their electron Fermi levels ( E F ) become equal. In the presence of an electrolyte, the potential of the Pt/electrolyte interface will shift due to the contact electricity and induce the spontaneous reduction of MnO 4 - anions on the Pt surface. Because the equilibrium of contact electrification is disturbed, electrons will transfer from n-GaAs to Pt through the tunneling effect. Thus, the accumulated positive holes at the n-GaAs/electrolyte interface make n-GaAs dissolve anodically along the Pt/n-GaAs/electrolyte 3-phase interface. Based on this principle, we developed a direct electrochemical nanoimprint lithography method applicable to crystalline semiconductors.

On the non-proportionality between wheel/rail contact forces and speed during wheelset passage over specific welds

NASA Astrophysics Data System (ADS)

Correa, Nekane; Vadillo, Ernesto G.; Santamaria, Javier; Blanco-Lorenzo, Julio

2018-01-01

This study investigates the influence on the wheel-rail contact forces of the running speed and the shape and position of weld defects along the track. For this purpose, a vertical dynamic model in the space domain is used. The model is obtained from the transformation between the domains of frequency and space using a Rational Fraction Polynomials (RFP) method, which is modified with multiobjective genetic algorithms in order to improve the fitting of track receptance and to assist integration during simulations. This produces a precise model with short calculation times, which is essential to this study. The wheel-rail contact is modelled using a non-linear Hertz spring. The contact forces are studied for several types of characteristic welds. The way in which forces vary as a function of weld position and running speed is studied for each type of weld. This paper studies some of the factors that affect the maximum forces when the vehicle moves over a rail weld, such as weld geometry, parametric excitation and contact stiffness. It is found that the maximum force in the wheel-rail contact when the vehicle moves over a weld is not always proportional to the running speed. The paper explains why it is not proportional in specific welds.

Effect of microstructure and surface features on wetting angle of a Fe-3.2 wt%C.E. cast iron with water

NASA Astrophysics Data System (ADS)

Riahi, Samira; Niroumand, Behzad; Dorri Moghadam, Afsaneh; Rohatgi, Pradeep K.

2018-05-01

In the present study, variation in surface wetting behavior of a hypoeutectic cast iron with its microstructural features and surface roughness was investigated. Samples with an identical composition, i.e. Fe-3.2 wt%C.E., and different microstructures (a gray cast iron with A-type flake graphite and a white cast iron) were fabricated by gravity casting of molten cast iron in a chill mold at different cooling rates. A variation of surface roughness was also developed by polishing, a four-stage electroetching and a four-stage mechanical abrading on the samples. Roughness and water contact angles of all surfaces were then measured. The surface roughness factor and the solid fraction in contact with water by the Wenzel and Cassie-Baxter contact models were also calculated and compared with the corresponding measured contact angles to find out which regime was active. Results indicated that the surface microstructure and the type of constituents present at the surface influenced the cast iron surface wettability and that it was possible to change the surface contact angle by modification of the surface microstructure. The mechanically abraded gray cast iron followed the Wenzel-type regime while the electroetched surfaces of gray cast iron exhibited a transition from Wenzel to Cassie-Baxter type regime. In white cast iron, the results indicated Wenzel type behavior in the electroetched samples while for the mechanically abraded samples, none of these two models could predict the wetting behavior. Furthermore, the wetting angles of both gray and white cast irons were measured after 1, 2, 3 and 4 weeks of air exposure. The results showed that the wetting angles of both samples increased to above 90° after one week of air exposure which was likely due to adsorption of low surface energy hydrocarbons on the surfaces.

[Determination of contact angle of pharmaceutical excipients and regulating effect of surfactants on their wettability].

PubMed

Hua, Dong-dong; Li, He-ran; Yang, Bai-xue; Song, Li-na; Liu, Tiao-tiao; Cong, Yu-tang; Li, San-ming

2015-10-01

To study the effects of surfactants on wettability of excipients, the contact angles of six types of surfactants on the surface of two common excipients and mixture of three surfactants with excipients were measured using hypsometry method. The results demonstrated that contact angle of water on the surface of excipients was associated with hydrophilcity of excipients. Contact angle was lowered with increase in hydrophilic groups of excipient molecules. The sequence of contact angle from small to large was starch < sodium benzoate < polyvinylpyrrolidone < sodium carboxymethylcellulose < sodium alginate < chitosan < hydroxypropyl methyl cellulose

Curva de rotação óptica de ESO-LV 5100550

NASA Astrophysics Data System (ADS)

Carvalho, D. B.; Soares, D. S. L.

2003-08-01

ESO-LV 5100550 é o membro mais fraco do par de galáxias austral SBG 357 (Soares et al. 1995). É classificada no catálogo RC3 como uma espiral ordinária de tipo inicial (early-type); porém, uma análise morfológica sugere que ela tenha uma grande barra. O objetivo do estudo é determinar sua cinemática de tal modo que possamos inferir mais a respeito de sua dinâmica, provavelmente perturbada, já que se espera que esteja sob forte influência da companheira ESO-LV 5100560. Apresentarei resultados parciais determinados a partir de espectros obtidos com o instrumento Double Spectrograph montado no telescópio Hale do Monte Palomar, EUA. As observações foram realizadas por D.S.L. Soares, P.M.V. Veiga e T.E. Nordgren, em 1998. Foram tomados espectros de fenda longa posicionada sobre a linha dos nodos do disco e ao longo da suposta barra. Os dados foram reduzidos com uso do pacote IRAF. Obtivemos o perfil de velocidades radiais na linha de visada ao longo das fendas e calculamos o desvio para o vermelho cosmológico do sistema, com base no espectro central. Determinamos as curvas de rotação deprojetadas, com base em cálculos para os valores teóricos esperados das componentes de velocidades puramente circulares em um disco inclinado. A inclinação do disco, dado fundamental nesta deprojeção, foi estimada através da média das elipticidades das isofotas mais externas.

Effect of two types of latex gloves and surfactants on polymerization inhibition of three polyvinylsiloxane impression materials.

PubMed

Peregrina, Alejandro; Land, Martin F; Feil, Phillip; Price, Connie

2003-09-01

Polymerization inhibition of polyvinylsiloxane impression materials has been reported when in sustained contact with some types of latex gloves. This study examined the polymerization inhibition of 3 polyvinylsiloxane impression materials placed in contact with surfaces subjected to prior contact with gloves or commonly used surfactants. A 2 x 3 x 4 x 2 design was used (n = 20), with 2 types of gloves (powdered and unpowdered), 3 types of polyvinylsiloxane impression materials (Aquasil, Extrude, and Affinis), 4 surfactant conditions (water, soap/water-rinse, alcohol, and unexposed), and 2 ambient temperatures of 22 degrees C and 36 degrees C. After glove exposure to surfactants, a glass surface was subjected to rubbing contact with the treated glove for a standardized time. After drying, automixed polyvinylsiloxane impression materials were dispensed onto the treated surface. Specimens were removed and evaluated for polymerization inhibition at the manufacturer's recommended polymerization time (36 degrees C), or after 15 minutes at 22 degrees C. Specimens were rated as polymerized, or as inhibited if any polyvinylsiloxane residue remained on the slab. A chi-square analysis was used to evaluate the results (alpha=.05). Setting inhibition was found only with one of the polyvinylsiloxane materials when alcohol was used as a surfactant. At 22 degrees C, the inhibition rate ranged from 95% to 100% for both glove types; at 36 degrees C inhibition ranged from 40% (unpowdered gloves) to 75% (powdered gloves), respectively. Under these in vitro conditions, glove exposure to alcohol resulted in polymerization inhibition of 1 of 3 tested polyvinylsiloxane impression materials (Extrude).

Pediatric Emergency Department Resource Utilization among Children with Primary Care Clinic Contact in the Preceding 2 Days: A Cross-Sectional Study.

PubMed

Grech, Christina K; Laux, Molly A; Burrows, Heather L; Macy, Michelle L; Pomeranz, Elaine S

2017-09-01

To characterize pediatric patient contacts with their primary care clinic in the 2 days preceding a visit to the emergency department (ED) and explore how the type of clinic contact relates to ED resource use. We conducted a retrospective chart review of 368 pediatric ED visits in the first 7 days of each month, from September 2012 to August 2013. Visits were included if the family contacted their child's general pediatric clinic in the study health system in the 2 days preceding the ED visit. Descriptive statistics were calculated. Primary outcomes were ED resource use (tests, treatments) and disposition (admission or discharge). Outcomes by type of clinic contact were compared with χ 2 statistics. Of 1116 records with ED visits in the 12 study weeks extracted from the electronic medical record, 368 ED visits met inclusion criteria. Most ED visits followed a single clinic contact (78.8%). Of the 474 clinic contacts, 149 were in-person visits, 216 phone calls when clinic was open, and 109 phone calls when clinic was closed. ED visits that followed an in-person clinic contact with advice to go to the ED had significantly greater rates of testing and admission than those advised to go to the ED after phone contact and those never advised to go to the ED. In-person clinic visits with advice to go to the ED were associated with the greatest ED resource use. Limitations include a study of a single health system without a uniform process for triaging patients to the ED across clinics. Copyright © 2017 Elsevier Inc. All rights reserved.

Pneumococcal serotypes in adult non-invasive and invasive pneumonia in relation to child contact and child vaccination status.

PubMed

Rodrigo, Chamira; Bewick, Thomas; Sheppard, Carmen; Greenwood, Sonia; Macgregor, Vanessa; Trotter, Caroline; Slack, Mary; George, Robert; Lim, Wei Shen

2014-02-01

On a population level, pneumococcal conjugate vaccination in children has reduced the incidence of vaccine-type disease in all age groups, including older adults. Few individual level studies have been performed describing the pneumococcal serotypes associated with adult community acquired pneumonia (CAP) and quantifying associations with child contact and child vaccination status. Pneumococcal serotypes were determined using a validated multiplex immunoassay (Bio-Plex) in a large prospective cohort of adults hospitalised with CAP. Child (<16 years old) contact history and child pneumococcal vaccination status were obtained from patients and public health records, respectively. Of 1130 participants, 329 (29.1%) reported child contact, and pneumococcal infection was identified in 410 (36.3%). Pneumococcal CAP was commoner in adults with child contact (148/329 (45.0%) vs 262/801 (32.7%); adjusted OR 1.63, CI 1.25 to 2.14; p<0.001). A serotype was determined in 263 of 410 (64.1%) adults with pneumococcal CAP; 112 (42.6%) reported child contact, 38 (33.9%) with a vaccinated child. Adults in contact with a vaccinated child were significantly less likely to have vaccine-type CAP compared with adults in contact with an unvaccinated child (6 of 38 (15.8%) vs 25 of 74 (33.8%), respectively; OR 0.37, 95% CI 0.14 to 0.99; p=0.044). Pneumococcal aetiology in adult CAP is independently associated with child contact and implicated serotypes are influenced by child vaccination status. This is the first study to demonstrate these associations at an individual rather than population level; it affirms that 'herd protection' from childhood vaccination extends beyond adult invasive disease to pneumococcal CAP.

Exploring contacts facilitating transmission of influenza A(H5N1) virus between poultry farms in West Java, Indonesia: A major role for backyard farms?

PubMed

Wibawa, Hendra; Karo-Karo, Desniwaty; Pribadi, Eko Sugeng; Bouma, Annemarie; Bodewes, Rogier; Vernooij, Hans; Diyantoro; Sugama, Agus; Muljono, David H; Koch, Guus; Tjatur Rasa, Fadjar Sumping; Stegeman, Arjan

2018-08-01

Highly pathogenic avian influenza virus (HPAIV) H5N1 has been reported in Asia, including Indonesia since 2003. Although several risk factors related to the HPAIV outbreaks in poultry in Indonesia have been identified, little is known of the contact structure of farms of different poultry production types (backyard chickens, broilers, layers, and ducks). This study aims to quantify the contact rates associated with the movement of people, and movements of live birds and products and equipment that affect the risk of HPAIV H5N1 transmission between poultry farms in Indonesia. On 124 poultry farms in 6 districts in West Java, logbooks were distributed to record the movements of farmers/staff and visitors and their poultry contacts. Most movements in backyard chicken, commercial native chicken, broiler and duck farms were visits to and from other poultry farms, whilst in layer farms visits to and from poultry companies, visits to egg collection houses and visit from other poultry farms were most frequent. Over 75% of persons visiting backyard chicken and duck farms had previously visited other poultry farms on the same day. Visitors of backyard chicken farms had the highest average contact rate, either direct contact with poultry on other farms before the visits (1.35 contact/day) or contact during their visits in the farms (10.03 contact/day). These results suggest that backyard chicken farms are most at risk for transmission of HPAIV compared to farms of the other poultry production types. Since visits of farm-to-farm were high, backyard farms could also a potential source for HPAIV transmission to commercial poultry farms. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

Magmatic ore deposits in layered intrusions - Descriptive model for reef-type PGE and contact-type Cu-Ni-PGE deposits

USGS Publications Warehouse

Zientek, Michael L.

2012-01-01

Layered, ultramafic to mafic intrusions are uncommon in the geologic record, but host magmatic ore deposits containing most of the world's economic concentrations of platinum-group elements (PGE) (figs. 1 and 2). These deposits are mined primarily for their platinum, palladium, and rhodium contents (table 1). Magmatic ore deposits are derived from accumulations of crystals of metallic oxides, or immiscible sulfide, or oxide liquids that formed during the cooling and crystallization of magma, typically with mafic to ultramafic compositions. "PGE reefs" are stratabound PGE-enriched lode mineralization in mafic to ultramafic layered intrusions. The term "reef" is derived from Australian and South African literature for this style of mineralization and used to refer to (1) the rock layer that is mineralized and has distinctive texture or mineralogy (Naldrett, 2004), or (2) the PGE-enriched sulfide mineralization that occurs within the rock layer. For example, Viljoen (1999) broadly defined the Merensky Reef as "a mineralized zone within or closely associated with an unconformity surface in the ultramafic cumulate at the base of the Merensky Cyclic Unit." In this report, we will use the term PGE reef to refer to the PGE-enriched mineralization, not the host rock layer. Within a layered igneous intrusion, reef-type mineralization is laterally persistent along strike, extending for the length of the intrusion, typically tens to hundreds of kilometers. However, the mineralized interval is thin, generally centimeters to meters thick, relative to the stratigraphic thickness of layers in an intrusion that vary from hundreds to thousands of meters. PGE-enriched sulfide mineralization is also found near the contacts or margins of layered mafic to ultramafic intrusions (Iljina and Lee, 2005). This contact-type mineralization consists of disseminated to massive concentrations of iron-copper-nickel-PGE-enriched sulfide mineral concentrations in zones that can be tens to hundreds of meters thick. The modes and textures of the igneous rocks hosting the mineralization vary irregularly on the scale of centimeters to meters; autoliths and xenoliths are common. Mineralization occurs in the igneous intrusion and in the surrounding country rocks. Mineralization can be preferentially localized along contact with country rocks that are enriched in sulfur-, iron-, or CO2-bearing lithologies. Reef-type and contact-type deposits, in particular those in the Bushveld Complex, South Africa, are the world's primary source of platinum and rhodium (tables 2 and 3; fig. 2). Reef-type PGE deposits are mined only in the Bushveld Complex (Merensky Reef and UG2), the Stillwater Complex (J-M Reef), and the Great Dyke (Main Sulphide Layer). PGE-enriched contact-type deposits are only mined in the Bushveld Complex. The other deposits in tables 2 and 3 are undeveloped; some are still under exploration.

Poison Ivy Rash

MedlinePlus

... Poison ivy rash is a type of allergic contact dermatitis caused by an oily resin called urushiol. It's ... so can help reduce the severity of the rash. If you think your pet may be ... think you've come into contact with poison ivy, wash your clothing promptly with ...

Microbial biofilm detection on food contact surfaces by macro-scale fluorescence imaging

USDA-ARS?s Scientific Manuscript database

Hyperspectral fluorescence imaging methods were utilized to evaluate the potential of multispectral fluorescence methods for detection of pathogenic biofilm formations on four types of food contact surface materials: stainless steel, high density polyethylene (HDPE) commonly used for cutting boards,...

Pseudophakodonesis and corneal endothelial contact: direct observations by high-speed cinematography.

PubMed Central

Jacobs, P M; Cheng, H; Price, N C

1983-01-01

High-speed cinematography was used to observe the movement of Federov type I lens implants within the anterior chamber. Our measurements suggest that in most patients contact between the lens implant and corneal endothelium does not occur. Images PMID:6615750

Contact Tracing Activities during the Ebola Virus Disease Epidemic in Kindia and Faranah, Guinea, 2014

PubMed Central

Taylor, Melanie M.; Dee, Jacob; Hakim, Avi; Cantey, Paul; Lim, Travis; Bah, Hawa; Camara, Sékou Mohamed; Ndongmo, Clement B.; Togba, Mory; Touré, Leonie Yvonne; Bilivogui, Pepe; Sylla, Mohammed; Kinzer, Michael; Coronado, Fátima; Tongren, Jon Eric; Swaminathan, Mahesh; Mandigny, Lise; Diallo, Boubacar; Seyler, Thomas; Rondy, Marc; Rodier, Guénaël; Perea, William A.; Dahl, Benjamin

2015-01-01

The largest recorded Ebola virus disease epidemic began in March 2014; as of July 2015, it continued in 3 principally affected countries: Guinea, Liberia, and Sierra Leone. Control efforts include contact tracing to expedite identification of the virus in suspect case-patients. We examined contact tracing activities during September 20–December 31, 2014, in 2 prefectures of Guinea using national and local data about case-patients and their contacts. Results show less than one third of case-patients (28.3% and 31.1%) were registered as contacts before case identification; approximately two thirds (61.1% and 67.7%) had no registered contacts. Time to isolation of suspected case-patients was not immediate (median 5 and 3 days for Kindia and Faranah, respectively), and secondary attack rates varied by relationships of persons who had contact with the source case-patient and the type of case-patient to which a contact was exposed. More complete contact tracing efforts are needed to augment control of this epidemic. PMID:26488116

Contact Tracing Activities during the Ebola Virus Disease Epidemic in Kindia and Faranah, Guinea, 2014.

PubMed

Dixon, Meredith G; Taylor, Melanie M; Dee, Jacob; Hakim, Avi; Cantey, Paul; Lim, Travis; Bah, Hawa; Camara, Sékou Mohamed; Ndongmo, Clement B; Togba, Mory; Touré, Leonie Yvonne; Bilivogui, Pepe; Sylla, Mohammed; Kinzer, Michael; Coronado, Fátima; Tongren, Jon Eric; Swaminathan, Mahesh; Mandigny, Lise; Diallo, Boubacar; Seyler, Thomas; Rondy, Marc; Rodier, Guénaël; Perea, William A; Dahl, Benjamin

2015-11-01

The largest recorded Ebola virus disease epidemic began in March 2014; as of July 2015, it continued in 3 principally affected countries: Guinea, Liberia, and Sierra Leone. Control efforts include contact tracing to expedite identification of the virus in suspect case-patients. We examined contact tracing activities during September 20-December 31, 2014, in 2 prefectures of Guinea using national and local data about case-patients and their contacts. Results show less than one third of case-patients (28.3% and 31.1%) were registered as contacts before case identification; approximately two thirds (61.1% and 67.7%) had no registered contacts. Time to isolation of suspected case-patients was not immediate (median 5 and 3 days for Kindia and Faranah, respectively), and secondary attack rates varied by relationships of persons who had contact with the source case-patient and the type of case-patient to which a contact was exposed. More complete contact tracing efforts are needed to augment control of this epidemic.

Highly reliable contacts for lead-salt diode lasers

NASA Astrophysics Data System (ADS)

Lo, W.

1981-02-01

In order to improve the long term reliability of lead-salt diode lasers, ohmic contacts of multilayer, thin-film structures consisting of In plus Au, Pt, Ni, and Pd have been studied. Diode lasers of PbSnTe fabricated with a variety of contacts were tested during room-temperature storage and during accelerated aging tests. The results show that contact reliability can be improved when multiple overlapping films are used. After 4500 h of baking at 60 C, lasers with In-Au-Pd-Au contacts on both sides showed the least resistance increase (10%). For lasers with In-Au-Pt-Au contacts, 1 h of baking at 60 C is equivalent to 2 d storage at room temperature. Extrapolating these results, a 70% increase in contact resistance is expected for this type of laser after 9000 d of storage at room temperature. The data also suggests that a smaller increase in contact resistance can be expected for lasers fabricated with In-Au-Ni and In-Au-Pd-Au contacts.

Carbon-Fiber Brush Heat Exchangers

NASA Technical Reports Server (NTRS)

Knowles, Timothy R.

2004-01-01

Velvetlike and brushlike pads of carbon fibers have been proposed for use as mechanically compliant, highly thermally conductive interfaces for transferring heat. A pad of this type would be formed by attaching short carbon fibers to either or both of two objects that one desires to place in thermal contact with each other. The purpose of using a thermal-contact pad of this or any other type is to reduce the thermal resistance of an interface between a heat source and a heat sink.

Contact stresses modeling at the Panda-type fiber single-layer winding and evaluation of their impact on the fiber optic properties

NASA Astrophysics Data System (ADS)

Lesnikova, Yu I.; Smetannikov, O. Yu; Trufanov, A. N.; Trufanov, N. A.

2017-02-01

The impact of contact transverse forces on the birefringence of the single-mode polarization-maintaining Panda-type fiber is numerically modeled. It has been established that with a single-row power winding on a cylindrical mandrel, the fiber tension at winding is the principal factor that influences birefringence. When coiling the fiber based on the local defect microbending, the birefringence at the microbending point differs from that of the free fiber by 1.3%.

Analysis by rotavirus gene 6 reverse transcriptase-polymerase chain reaction assay of rotavirus-positive gastroenteritis cases observed during the vaccination phase of the Rotavirus Efficacy and Safety Trial (REST)

PubMed Central

Matson, David O; Vesikari, Timo; Dennehy, Penelope; Dallas, Michael D; Goveia, Michelle G; Itzler, Robbin F; Ciarlet, Max

2014-01-01

During the vaccination phase of the Rotavirus Efficacy and Safety Trial (REST), the period between the administration of dose 1 through 13 days after the administration of dose 3, there were more wild-type rotavirus gastroenteritis (RVGE) cases among vaccine recipients compared with placebo recipients using the protocol-specified microbiological plaque assay in the clinical-efficacy cohort, a subset of subjects where vaccine efficacy against RVGE of any severity was assessed. In this study, a rotavirus genome segment 6-based reverse transcriptase–polymerase chain reaction assay was applied post hoc to clarify the accuracy of type categorization of all these RVGE cases in vaccine recipients during the vaccination phase of REST. The assay characterized 147 (90%) of 163 re-assayed RVGE cases or rotavirus-associated health care contacts as type-determinable: either wild-type or vaccine-type rotavirus strains. In the clinical-efficacy cohort (N = 5673), 19 (18.8%) of 101 samples from RVGE cases contained wild-type rotavirus, 70 (69.3%) vaccine virus, and 12 (11.9%) were indeterminable. In the large-scale cohort (N = 68,038), 10 (34.5%) of 29 samples from RVGE-related health care contacts contained wild-type rotavirus strains, 15 (51.7%) vaccine-type rotavirus strains, and 4 (13.8%) were indeterminable. Of the 33 samples from RVGE cases in placebo recipients, all were confirmed to contain wild-type rotaviruses. Altogether, this post-hoc re-evaluation showed that the majority (75%) of type-determinable RVGE cases or health care contacts that occurred during the vaccination phase of REST in vaccine recipients were associated with vaccine-type rotavirus strains rather than wild-type rotavirus strains. PMID:25424931

Analysis by rotavirus gene 6 reverse transcriptase-polymerase chain reaction assay of rotavirus-positive gastroenteritis cases observed during the vaccination phase of the Rotavirus Efficacy and Safety Trial (REST).

PubMed

Matson, David O; Vesikari, Timo; Dennehy, Penelope; Dallas, Michael D; Goveia, Michelle G; Itzler, Robbin F; Ciarlet, Max

2014-01-01

During the vaccination phase of the Rotavirus Efficacy and Safety Trial (REST), the period between the administration of dose 1 through 13 days after the administration of dose 3, there were more wild-type rotavirus gastroenteritis (RVGE) cases among vaccine recipients compared with placebo recipients using the protocol-specified microbiological plaque assay in the clinical-efficacy cohort, a subset of subjects where vaccine efficacy against RVGE of any severity was assessed. In this study, a rotavirus genome segment 6-based reverse transcriptase-polymerase chain reaction assay was applied post hoc to clarify the accuracy of type categorization of all these RVGE cases in vaccine recipients during the vaccination phase of REST. The assay characterized 147 (90%) of 163 re-assayed RVGE cases or rotavirus-associated health care contacts as type-determinable: either wild-type or vaccine-type rotavirus strains. In the clinical-efficacy cohort (N = 5673), 19 (18.8%) of 101 samples from RVGE cases contained wild-type rotavirus, 70 (69.3%) vaccine virus, and 12 (11.9%) were indeterminable. In the large-scale cohort (N = 68,038), 10 (34.5%) of 29 samples from RVGE-related health care contacts contained wild-type rotavirus strains, 15 (51.7%) vaccine-type rotavirus strains, and 4 (13.8%) were indeterminable. Of the 33 samples from RVGE cases in placebo recipients, all were confirmed to contain wild-type rotaviruses. Altogether, this post-hoc re-evaluation showed that the majority (75%) of type-determinable RVGE cases or health care contacts that occurred during the vaccination phase of REST in vaccine recipients were associated with vaccine-type rotavirus strains rather than wild-type rotavirus strains.

Tunnel oxide passivated contacts formed by ion implantation for applications in silicon solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reichel, Christian, E-mail: christian.reichel@ise.fraunhofer.de; National Renewable Energy Laboratory; Feldmann, Frank

Passivated contacts (poly-Si/SiO{sub x}/c-Si) doped by shallow ion implantation are an appealing technology for high efficiency silicon solar cells, especially for interdigitated back contact (IBC) solar cells where a masked ion implantation facilitates their fabrication. This paper presents a study on tunnel oxide passivated contacts formed by low-energy ion implantation into amorphous silicon (a-Si) layers and examines the influence of the ion species (P, B, or BF{sub 2}), the ion implantation dose (5 × 10{sup 14 }cm{sup −2} to 1 × 10{sup 16 }cm{sup −2}), and the subsequent high-temperature anneal (800 °C or 900 °C) on the passivation quality and junction characteristics using double-sided contacted silicon solar cells.more » Excellent passivation quality is achieved for n-type passivated contacts by P implantations into either intrinsic (undoped) or in-situ B-doped a-Si layers with implied open-circuit voltages (iV{sub oc}) of 725 and 720 mV, respectively. For p-type passivated contacts, BF{sub 2} implantations into intrinsic a-Si yield well passivated contacts and allow for iV{sub oc} of 690 mV, whereas implanted B gives poor passivation with iV{sub oc} of only 640 mV. While solar cells featuring in-situ B-doped selective hole contacts and selective electron contacts with P implanted into intrinsic a-Si layers achieved V{sub oc} of 690 mV and fill factor (FF) of 79.1%, selective hole contacts realized by BF{sub 2} implantation into intrinsic a-Si suffer from drastically reduced FF which is caused by a non-Ohmic Schottky contact. Finally, implanting P into in-situ B-doped a-Si layers for the purpose of overcompensation (counterdoping) allowed for solar cells with V{sub oc} of 680 mV and FF of 80.4%, providing a simplified and promising fabrication process for IBC solar cells featuring passivated contacts.« less

The type of mat (Contact vs. Photocell) affects vertical jump height estimated from flight time.

PubMed

García-López, Juan; Morante, Juan C; Ogueta-Alday, Ana; Rodríguez-Marroyo, Jose A

2013-04-01

The purposes of this study were to analyze the validity and reliability of 2 photocell mats and to probe the possible influence of the type of mat (contact vs. photocell) on vertical jump height estimated from flight time. In 2 separate studies, 89 and 92 physical students performed 3 countermovement jumps that were simultaneously registered by a Force Plate (gold standard method), 2 photocell mats (SportJump System Pro and ErgoJump Plus), and a contact mat (SportJump-v1.0). The first study showed that the 2 photocell mats underestimated the vertical jump height (1.3 ± 0.2 cm and 5.9 ± 5.2 cm, respectively), but only SportJump System Pro showed a high correlation with the Force Plate (r = 0.999 and 0.676, respectively) and good intraday reliability (coefficient of variation = 2.98 and 15.94%, intraclass correlation coefficients = 0.95-0.97 and 0.45-0.57, respectively). The second study demonstrated a strong correlation (r = 0.994) between the 2 technologies (contact vs. photocell mats) with differences in vertical jump height of 2.0 ± 0.8 cm (95% confidence interval = 1.9-2.1 cm), which depended on both flight time and subjects' body mass. In conclusion, SportJump System Pro was a valid and reliable device. The new devices to measure vertical jump height from flight time should be validated. The type of mat (contact vs. photocell) affected approximately 6% the vertical jump height (approximately 2 cm in this study), which should be considered in further studies. The use of validated photocell mats instead of the contact mats was recommended.

Contact formation and patterning approaches for group-III nitride light emitters

NASA Astrophysics Data System (ADS)

Hou, Wenting

Solid state lighting via light emitting diodes (LEDs) and laser diodes (LDs) is a rapidly progressing technology with the potential to greatly exceed the efficiency of traditional lighting systems. This dissertation focuses on the development of electrical contacts and patterning schemes for highly efficient green LEDs and LD structures. Efficiency of LEDs can be greatly improved by means of nano-patterning processes. LEDs grown on nano-imprint patterned sapphire substrates showed promising performance, with improvement in both internal quantum efficiency and light extraction efficiency. As an alternative to nano-imprint lithography, this study utilized a simple method to generate irregular nano-patterns by a Ni self-assembly process and applied the process to both sapphire substrate and n-GaN template. In both approaches, the nano-patterned LEDs showed an improvement in light output power. For the device fabrication of LEDs and LDs, low-resistance ohmic contacts are essential for high efficiency. In search of a highly transparent ohmic contact to p-type GaN, I analyzed various metal/indium-tin-oxide (ITO) (Ag/ITO, AgCu/ITO, Ni/ITO, and NiZn/ITO) contact schemes and compared them with Ni/Au, NiZn/Ag, and ITO contacts. For ITO-based contacts, the inserted metal layer can boost conductivity while the ITO thickness can be optimized for constructive transmission interference on GaN exceeding the extraction from bare GaN. The best compromise was obtained for an Ag/ITO (3 nm /67 nm) ohmic contact, with a relative transmittance of 97% of the bare GaN near 530 nm, and a specific contact resistance of 3x10-2 O·cm 2. The contact proved particularly suitable for green light emitting diodes in epi-up geometry. Graphene as another alternative transparent p-contact was also evaluated. Furthermore, this dissertation offered a pre-deposition treatment to contact schemes on undoped and n-doped GaN, rendering a standard post-deposition annealing step unnecessary. As-deposited Ti/Al/Ti/Au usually forms a Schottky contact. By means of oxygen rapid thermal annealing prior to the metal deposition, the contact developed an ohmic behavior with a specific contact resistance of 3.8x10-5 O cm2. X-ray photoelectron spectroscopy characterization showed that the Ga 3d electron binding energy increased with the pre-treatment, indicating a shift of the Fermi level closer to the conduction band edge. This explained the improvement in contact performance. While low contact resistance to GaN-based devices has been achieved to p-type and n-type layers separately, contacts are likely to degrade when both types need to be integrated into a single fabrication process in bipolar devices. This dissertation presents a solution to the problem by the pre-deposition oxygen thermal treatment on n-GaN. By utilizing this process, an important gain in device fabrication flexibility was realized. LEDs with the integrated process for both n- and p-contacts showed lower series resistance and lower voltage drop compared to those with separately optimized contacts. In addition to the fabrication of LEDs, the development of green LDs was studied. To extend the emission wavelength of AlGaInN-based LDs to a 500 nm green spectral region, both highly efficient active layers and suitable optical confinement are critical. This work presents the development progress by first identifying active regions that show stimulated emission at 450 nm under optical excitation. Then such layers were embedded in an etched cavity. Under electrical injection, the same transition appeared as a short-wavelength shoulder of a broader band. By using a silver mirror on the p-side, an enhanced optical confinement was obtained, and the 450 nm emission showed an even better dominance over the long-wavelength contribution. As an alternative, an optical confinement was implemented by applying AlGaN cladding layers in ridge wave-guided structures. A superior optical confinement was achieved in an epitaxial ridge re-growth approach. Under pulsed electrical injection, narrow-peak emission in the 510--520 nm range was achieved, rendering the approach suitable for the further development of blue and green laser diodes.

Reasons for encounter and disease patterns in Danish primary care: changes over 16 years.

PubMed

Moth, Grete; Olesen, Frede; Vedsted, Peter

2012-06-01

Approximately 98% of Danish citizens are listed with a general practice which they consult for medical advice. Although 85% of the population contact their general practitioner (GP) every year, little is known about these contacts. The aim of the present paper is to gain updated knowledge about patients' reasons for encounter and the GP activities and to make comparisons with a similar study from 1993. All GPs in the Central Denmark Region were invited to register all contacts during one randomly chosen day within a year. The registration included questions about patients' reasons for encounter, the types and contents of the contacts, referrals, and distribution between new episodes and follow-up contacts. Aggregated data were compared with the results from 1993. A total of 404 (46%) GPs participated. The number of contacts per 1000 inhabitants had risen by 19.7%. The reasons for encounter and final diagnoses resembled those in 1993. Musculoskeletal, psychological, and respiratory problems were the most common reasons for encounter, psychological problems being the only type to increase over the period. Interestingly, the proportion of diagnoses within the ICPC 'A' chapter rose from 13.5 to 19.7%. The referral rate rose by 2% (relative: 18.7%) from 10.7% to 12.7% and the share of follow-up contacts rose from 45.9% to 50.4% (relative: 8.7%). Quite small changes were seen in the patterns of reasons for encounter and diagnoses from 1993 to 2009. However, an increase was found in contacts with general practice and referrals and in the proportion of follow-ups.

Ultrasonic model and system for measurement of corneal biomechanical properties and validation on phantoms.

PubMed

Liu, Jun; He, Xiaoyin; Pan, Xueliang; Roberts, Cynthia J

2007-01-01

Non-invasive measurement of biomechanical properties of corneas may provide important information for ocular disease management and therapeutic procedures. An ultrasonic non-destructive evaluation method with a wave propagation model was developed to determine corneal biomechanical properties in vivo. In this study, we tested the feasibility of the approach in differentiating the mechanical properties of soft contact lenses as corneal phantoms. Three material types of soft contact lenses (six samples in each group) were measured using a broadband ultrasound transducer. The ultrasonic reflections from the contact lenses were recorded by a 500MHz/8-bit digitizer, and displayed and processed by a PC. A reference signal was recorded to compute the normalized power spectra using Fast Fourier Transformation. An inverse algorithm based on least-squares minimization was used to reconstruct three parameters of the contact lenses: density, thickness, and elastic constants lambda+2micro. The thickness of each sample was verified using an electronic thickness gauge, and the averaged density for each type of lenses was verified using Archimedes' principle and manufacturer's report. Our results demonstrated that the ultrasonic system was able to differentiate the elastic properties of the three types of the soft contact lenses with statistical significance (P-value<0.001). The reconstructed thicknesses and densities agreed well with the independent measurements. Our studies on corneal phantoms indicated that the ultrasonic system was sensitive and accurate in measuring the material properties of cornea-like structures. It is important to optimize the system for in vivo measurements.

2D halide perovskite-based van der Waals heterostructures: contact evaluation and performance modulation

NASA Astrophysics Data System (ADS)

Guo, Yaguang; Saidi, Wissam A.; Wang, Qian

2017-09-01

Halide perovskites and van der Waals (vdW) heterostructures are both of current interest owing to their novel properties and potential applications in nano-devices. Here, we show the great potential of 2D halide perovskite sheets (C4H9NH3)2PbX4 (X  =  Cl, Br and I) that were synthesized recently (Dou et al 2015 Science 349 1518-21) as the channel materials contacting with graphene and other 2D metallic sheets to form van der Waals heterostructures for field effect transistor (FET). Based on state-of-the-art theoretical simulations, we show that the intrinsic properties of the 2D halide perovskites are preserved in the heterojunction, which is different from the conventional contact with metal surfaces. The 2D halide perovskites form a p-type Schottky barrier (Φh) contact with graphene, where tunneling barrier exists, and a negative band bending occurs at the lateral interface. We demonstrate that the Schottky barrier can be turned from p-type to n-type by doping graphene with nitrogen atoms, and a low-Φh or an Ohmic contact can be realized by doping graphene with boron atoms or replacing graphene with other high-work-function 2D metallic sheets such as ZT-MoS2, ZT-MoSe2 and H-NbS2. This study not only predicts a 2D halide perovskite-based FETs, but also enhances the understanding of tuning Schottky barrier height in device applications.

Study and optimization of the macroscopic electrical response of carbon based nanocomposites for advanced applications

NASA Astrophysics Data System (ADS)

Silva, Jaime Pedro Oliveira da

A presente tese centrou-se no estudo da resposta da constante dieletrica e condutividade eletrica em materiais compositos nos quais o reforco tinha uma elevada proporcao entre comprimento e diametro. O objeto de estudo foi o efeito de um reforco com uma elevada razao entre comprimento e diametro, concentracao e orientacao na resposta eletrica e dieletrica de um composito. Estes compositos tem uma grande importancia no desenvolvimento de materiais para sensores e atuadores. Num primeiro momento da dissertacao, explorou-se a resposta da constante dieletrica de um composito constituido por nanotubos de carbono como reforco e uma matriz polimerica. Verificou-se que um aumento da razao entre comprimento e diametro do reforco tem o efeito de aumentar a constante dieletrica do composito para uma igual fracao volumetrica de reforco. Constatou-se tambem que materiais na fase nematica demonstram uma constante dieletrica mais baixa quando comparados com materiais onde o reforco esta distribuido aleatoriamente. Ficou ainda demonstrado nesta dissertacao que materiais na fase nematica com razoes entre o comprimento e diametro diferentes a constante dieletrica segue uma lei de potencia. Numa segunda fase do trabalho, foi explorada a condutividade de nanocompositos polimericos reforcados com nanotubos de carbono, atraves de um modelo baseado em cilindros impenetraveis. Ficou demonstrado que o modelo e apropriado para descrever a condutividade eletrica de um nanocomposito polimerico reforcado com nanotubos. As simulacoes desenvolvidas demonstram que, aumentando a razao entre o comprimento e o diametro dos nanotubos de carbono, aumenta a condutividade eletrica do nanocomposito. No entanto, verifica-se que aumentando a anisotropia diminui a condutividade, sendo este efeito mais evidente para fracoes volumetricas maiores. Nesta dissertacao comprovou-se ainda que uma microestrutura gerada por um algoritmo de empacotamento sequencial pode ser descrita por um grafo aleatorio e que a condutividade num composito reforcado com nanofibras de carbono pode ser descrito por uma rede de Bethe. Atraves do uso da teoria das redes complexas, chegou-se a uma expressao para o limite de percolacao e, do mesmo modo, demonstrou-se que “hopping” entre fibras adjacentes resulta numa expressao que corresponde a um regime de desordem fraca. No trabalho desenvolvido tambem foi calculado os expoentes criticos, atraves da teoria das redes, para um sistema 3D composto por cilindros impenetraveis com uma interacao de curto alcance, demonstrando que os expoentes criticos estao relacionados por uma relacao de hiperescala comum para 3D e nao pertencem a mesma classe de universalidade como a percolacao numa rede. A aplicacao do modelo desenvolvido a compositos de epoxy reforcada, com diferentes metodos de dispersao de nanofibras de carbono, revelou que os metodos de dispersao usados para preparar os compositos tem uma forte influencia nas propriedades eletricas que podem ser capturadas pelo modelo. Neste contexto, ficou ainda demonstrado que a condutividade eletrica pode ser descrita por um regime de desordem fraca, isto ´e, um regime onde todas as conexoes fibra-fibra participam na condutividade do composito. O modelo desenvolvido foi aplicado igualmente a compositos de poly (vinylidene fluoride) reforcado com nanotubos de carbono com diferentes tratamentos de termicos de oxidacao. Verificou-se que os tratamentos de superficie aumentam o limite de percolacao e diminuem a condutividade. Nesta dissertacao provamos ainda que a condutividade do composito pode ser atribuida a um mecanismo de “hopping”, fortemente afetado pelos tratamentos de superficie dos reforcos.

Fabrication of stable electrode/diffusion barrier layers for thermoelectric filled skutterudite devices

DOEpatents

Jie, Qing; Ren, Zhifeng; Chen, Gang

2015-12-08

Disclosed are methods for the manufacture of n-type and p-type filled skutterudite thermoelectric legs of an electrical contact. A first material of CoSi.sub.2 and a dopant are ball-milled to form a first powder which is thermo-mechanically processed with a second powder of n-type skutterudite to form a n-type skutterudite layer disposed between a first layer and a third layer of the doped-CoSi.sub.2. In addition, a plurality of components such as iron, and nickel, and at least one of cobalt or chromium are ball-milled form a first powder that is thermo-mechanically processed with a p-type skutterudite layer to form a p-type skutterudite layer "second layer" disposed between a first and a third layer of the first powder. The specific contact resistance between the first layer and the skutterudite layer for both the n-type and the p-type skutterudites subsequent to hot-pressing is less than about 10.0 .mu..OMEGA.cm.sup.2.

Fabrication of stable electrode/diffusion barrier layers for thermoelectric filled skutterudite devices

DOEpatents

Jie, Qing; Ren, Zhifeng; Chen, Gang

2017-08-01

Disclosed are methods for the manufacture of n-type and p-type filled skutterudite thermoelectric legs of an electrical contact. A first material of CoSi.sub.2 and a dopant are ball-milled to form a first powder which is thermo-mechanically processed with a second powder of n-type skutterudite to form a n-type skutterudite layer disposed between a first layer and a third layer of the doped-CoSi.sub.2. In addition, a plurality of components such as iron, and nickel, and at least one of cobalt or chromium are ball-milled form a first powder that is thermo-mechanically processed with a p-type skutterudite layer to form a p-type skutterudite layer "second layer" disposed between a first and a third layer of the first powder. The specific contact resistance between the first layer and the skutterudite layer for both the n-type and the p-type skutterudites subsequent to hot-pressing is less than about 10.0 .mu..OMEGA.cm.sup.2.

Alternative methods to model frictional contact surfaces using NASTRAN

NASA Technical Reports Server (NTRS)

Hoang, Joseph

1992-01-01

Elongated (slotted) holes have been used extensively for the integration of equipment into Spacelab racks. In the past, this type of interface has been modeled assuming that there is not slippage between contact surfaces, or that there is no load transfer in the direction of the slot. Since the contact surfaces are bolted together, the contact friction provides a load path determined by the normal applied force (bolt preload) and the coefficient of friction. Three alternate methods that utilize spring elements, externally applied couples, and stress dependent elements are examined to model the contacted surfaces. Results of these methods are compared with results obtained from methods that use GAP elements and rigid elements.

Contact centers, pervasive computing and telemedicine: a quality health care triangle.

PubMed

Maglaveras, Nicos

2004-01-01

The Citizen Health System (CHS) is a European Commission (CEC) funded project in the field of IST for Health. Its main goal is to develop a generic contact center which in its pilot stage can be used in the monitoring, treatment and management of chronically ill patients at home in Greece, Spain, and Germany. Such contact centers, using any type of communication technology, and providing timely and preventive prompting to the patients are envisaged in the future to evolve into well-being contact centers providing services to all citizens. In this paper, we present the structure of such a generic contact center and present its major achievements, and their impact to the quality of health delivery.

Non-contact plant growth measurement method and system based on ubiquitous sensor network technologies.

PubMed

Suk, Jinweon; Kim, Seokhoon; Ryoo, Intae

2011-01-01

This paper proposes a non-contact plant growth measurement system using infrared sensors based on the ubiquitous sensor network (USN) technology. The proposed system measures plant growth parameters such as the stem radius of plants using real-time non-contact methods, and generates diameter, cross-sectional area and thickening form of plant stems using this measured data. Non-contact sensors have been used not to cause any damage to plants during measurement of the growth parameters. Once the growth parameters are measured, they are transmitted to a remote server using the sensor network technology and analyzed in the application program server. The analyzed data are then provided for administrators and a group of interested users. The proposed plant growth measurement system has been designed and implemented using fixed-type and rotary-type infrared sensor based measurement methods and devices. Finally, the system performance is compared and verified with the measurement data that have been obtained by practical field experiments.

Plant dermatitis. Possible culprits go far beyond poison ivy.

PubMed

Juckett, G

1996-09-01

Given the variety of existing plant species in the environment, it is remarkable that people have adjusted as well as they have to the many plants that can cause uncomfortable skin reactions. With a basic understanding of the types of reaction and the common plants that cause each type, physicians can help patients discover the source of the dermatitis and thus prevent reexposure. In immediate contact dermatitis, welts form rapidly after patients brush against an offending plant, but the urticarial rash is short-lived. In irritant contact dermatitis, the skin is traumatized mechanically (eg, with cactus spines) or chemically (eg, with capsaicin from hot peppers), producing a more persistent skin reaction. Phytophotodermatitis occurs when the skin is exposed to sunlight after contact with an offending plant; reactions are erythema, pruritus, vesiculation, and subsequent hyperpigmentation. Allergic contact dermatitis, typified by the rash of poison ivy, is a cell-mediated immune response that occurs in previously sensitized persons. Erythema, vesiculation, and pruritus, which usually heal without causing pigmentary changes, may last for several weeks.

Structure of a bacterial type III secretion system in contact with a host membrane in situ

NASA Astrophysics Data System (ADS)

Nans, Andrea; Kudryashev, Mikhail; Saibil, Helen R.; Hayward, Richard D.

2015-12-01

Many bacterial pathogens of animals and plants use a conserved type III secretion system (T3SS) to inject virulence effector proteins directly into eukaryotic cells to subvert host functions. Contact with host membranes is critical for T3SS activation, yet little is known about T3SS architecture in this state or the conformational changes that drive effector translocation. Here we use cryo-electron tomography and sub-tomogram averaging to derive the intact structure of the primordial Chlamydia trachomatis T3SS in the presence and absence of host membrane contact. Comparison of the averaged structures demonstrates a marked compaction of the basal body (4 nm) occurs when the needle tip contacts the host cell membrane. This compaction is coupled to a stabilization of the cytosolic sorting platform-ATPase. Our findings reveal the first structure of a bacterial T3SS from a major human pathogen engaged with a eukaryotic host, and reveal striking `pump-action' conformational changes that underpin effector injection.

Multi-Layer SnSe Nanoflake Field-Effect Transistors with Low-Resistance Au Ohmic Contacts

NASA Astrophysics Data System (ADS)

Cho, Sang-Hyeok; Cho, Kwanghee; Park, No-Won; Park, Soonyong; Koh, Jung-Hyuk; Lee, Sang-Kwon

2017-05-01

We report p-type tin monoselenide (SnSe) single crystals, grown in double-sealed quartz ampoules using a modified Bridgman technique at 920 °C. X-ray powder diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX) measurements clearly confirm that the grown SnSe consists of single-crystal SnSe. Electrical transport of multi-layer SnSe nanoflakes, which were prepared by exfoliation from bulk single crystals, was conducted using back-gated field-effect transistor (FET) structures with Au and Ti contacts on SiO2/Si substrates, revealing that multi-layer SnSe nanoflakes exhibit p-type semiconductor characteristics owing to the Sn vacancies on the surfaces of SnSe nanoflakes. In addition, a strong carrier screening effect was observed in 70-90-nm-thick SnSe nanoflake FETs. Furthermore, the effect of the metal contacts to multi-layer SnSe nanoflake-based FETs is also discussed with two different metals, such as Ti/Au and Au contacts.

Few-Layer WSe2 Schottky Junction-Based Photovoltaic Devices through Site-Selective Dual Doping.

PubMed

Ko, Seungpil; Na, Junhong; Moon, Young-Sun; Zschieschang, Ute; Acharya, Rachana; Klauk, Hagen; Kim, Gyu-Tae; Burghard, Marko; Kern, Klaus

2017-12-13

Ultrathin sheets of two-dimensional (2D) materials like transition metal dichalcogenides have attracted strong attention as components of high-performance light-harvesting devices. Here, we report the implementation of Schottky junction-based photovoltaic devices through site-selective surface doping of few-layer WSe 2 in lateral contact configuration. Specifically, whereas the drain region is covered by a strong molecular p-type dopant (NDP-9) to achieve an Ohmic contact, the source region is coated with an Al 2 O 3 layer, which causes local n-type doping and correspondingly an increase of the Schottky barrier at the contact. By scanning photocurrent microscopy using green laser light, it could be confirmed that photocurent generation is restricted to the region around the source contact. The local photoinduced charge separation is associated with a photoresponsivity of up to 20 mA W -1 and an external quantum efficiency of up to 1.3%. The demonstrated device concept should be easily transferrable to other van der Waals 2D materials.

Validity of Gō models: comparison with a solvent-shielded empirical energy decomposition.

PubMed

Paci, Emanuele; Vendruscolo, Michele; Karplus, Martin

2002-12-01

Do Gō-type model potentials provide a valid approach for studying protein folding? They have been widely used for this purpose because of their simplicity and the speed of simulations based on their use. The essential assumption in such models is that only contact interactions existing in the native state determine the energy surface of a polypeptide chain, even for non-native configurations sampled along folding trajectories. Here we use an all-atom molecular mechanics energy function to investigate the adequacy of Gō-type potentials. We show that, although the contact approximation is accurate, non-native contributions to the energy can be significant. The assumed relation between residue-residue interaction energies and the number of contacts between them is found to be only approximate. By contrast, individual residue energies correlate very well with the number of contacts. The results demonstrate that models based on the latter should give meaningful results (e.g., as used to interpret phi values), whereas those that depend on the former are only qualitative, at best.

Structure of a bacterial type III secretion system in contact with a host membrane in situ.

PubMed

Nans, Andrea; Kudryashev, Mikhail; Saibil, Helen R; Hayward, Richard D

2015-12-11

Many bacterial pathogens of animals and plants use a conserved type III secretion system (T3SS) to inject virulence effector proteins directly into eukaryotic cells to subvert host functions. Contact with host membranes is critical for T3SS activation, yet little is known about T3SS architecture in this state or the conformational changes that drive effector translocation. Here we use cryo-electron tomography and sub-tomogram averaging to derive the intact structure of the primordial Chlamydia trachomatis T3SS in the presence and absence of host membrane contact. Comparison of the averaged structures demonstrates a marked compaction of the basal body (4 nm) occurs when the needle tip contacts the host cell membrane. This compaction is coupled to a stabilization of the cytosolic sorting platform-ATPase. Our findings reveal the first structure of a bacterial T3SS from a major human pathogen engaged with a eukaryotic host, and reveal striking 'pump-action' conformational changes that underpin effector injection.

Evaluation of metal/indium-tin-oxide for transparent low-resistance contacts to p-type GaN.

PubMed

Hou, Wenting; Stark, Christoph; You, Shi; Zhao, Liang; Detchprohm, Theeradetch; Wetzel, Christian

2012-08-10

In search of a better transparent contact to p-GaN, we analyze various metal/indium-tin-oxide (ITO) (Ag/ITO, AgCu/ITO, Ni/ITO, and NiZn/ITO) contact schemes and compare to Ni/Au, NiZn/Ag, and ITO. The metal layer boosts conductivity while the ITO thickness can be adjusted to constructive transmission interference on GaN that exceeds extraction from bare GaN. We find a best compromise for an Ag/ITO (3 nm/67 nm) ohmic contact with a relative transmittance of 97% of the bare GaN near 530 nm and a specific contact resistance of 0.03 Ω·cm2. The contact proves suitable for green light-emitting diodes in epi-up geometry.

The effect of bottom boundary condition type on the behavior of adhesive contact of spherical probe on an elastic film

NASA Astrophysics Data System (ADS)

Zhu, X.; Xu, W.

2017-11-01

This study presents an investigation on the behavior of adhesive contact between a rigid sphere and an elastic film which is either perfectly bonded (case I) or in frictionless contact (case II) with a rigid substrate. By using linear fracture mechanics, we formulate an convenient semi-analytical approach to develop relations between the applied force, penetration depth and contact radius. Finite element analysis (FEA) is used to verify the relationships. Our results reveal that the interfacial boundary conditions between the film and substrate have distinct effects on the adhesive contact behavior between the sphere and the film. The aim of the present study is to provide an instructive inspiration for controlling adhesion strength of the thin film subject to adhesive contact.

Laser method for forming low-resistance ohmic contacts on semiconducting oxides

DOEpatents

Narayan, Jagdish

1981-01-01

This invention is a new method for the formation of high-quality ohmic contacts on wide-band-gap semiconducting oxides. As exemplified by the formation of an ohmic contact on n-type BaTiO.sub.3 containing a p-n junction, the invention entails depositing a film of a metallic electroding material on the BaTiO.sub.3 surface and irradiating the film with a Q-switched laser pulse effecting complete melting of the film and localized melting of the surface layer of oxide immediately underlying the film. The resulting solidified metallic contact is ohmic, has unusually low contact resistance, and is thermally stable, even at elevated temperatures. The contact does not require cleaning before attachment of any suitable electrical lead. This method is safe, rapid, reproducible, and relatively inexpensive.

Method for forming low-resistance ohmic contacts on semiconducting oxides

DOEpatents

Narayan, J.

1979-10-01

The invention provides a new method for the formation of high-quality ohmic contacts on wide-band-gap semiconducting oxides. As exemplified by the formation of an ohmic contact on n-type BaTiO/sub 3/ containing a p-n junction, the invention entails depositing a film of a metallic electroding material on the BaTiO/sub 3/ surface and irradiating the film with a Q-switched laser pulse effecting complete melting of the film and localized melting of the surface layer of oxide immediately underlying the film. The resulting solidified metallic contact is ohmic, has unusually low contact resistance, and is thermally stable, even at elevated temmperatures. The contact does not require cleaning before attachment of any suitable electrical lead. This method is safe, rapid, reproducible, and relatively inexpensive.

Search for Pauli exclusion principle violating atomic transitions and electron decay with a p-type point contact germanium detector

DOE PAGES

Abgrall, N.; Arnquist, I. J.; Avignone, F. T.; ...

2016-11-11

Here, a search for Pauli-exclusion-principle-violating K α electron transitions was performed using 89.5 kg-d of data collected with a p-type point contact high-purity germanium detector operated at the Kimballton Underground Research Facility. A lower limit on the transition lifetime of 5.8 × 10 30 s at 90% C.L. was set by looking for a peak at 10.6 keV resulting from the X-ray and Auger electrons present following the transition. A similar analysis was done to look for the decay of atomic K-shell electrons into neutrinos, resulting in a lower limit of 6.8 × 10 30 s at 90% C.L. Itmore » is estimated that the Majorana Demonstrator, a 44 kg array of p-type point contact detectors that will search for the neutrinoless double-beta decay of 76Ge, could improve upon these exclusion limits by an order of magnitude after three years of operation.« less

Effect of load, area of contact, and contact stress on the wear mechanisms of a bonded solid lubricant film

NASA Technical Reports Server (NTRS)

Fusaro, R. L.

1980-01-01

A pin on disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically tipped riders. Different projected contact stresses were obtained by applying loads of 2.5- to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build up of thick rider transfer films.

Effect of load, area of contact, and contact stress on the tribological properties of polyimide bonded graphite fluoride films

NASA Technical Reports Server (NTRS)

Fusaro, R. L.

1981-01-01

A pin-on-disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide-bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically-tipped riders. Different projected contact stresses were obtained by applying loads of 2.5-to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build-up of thick rider transfer films.

Contact effects analyzed by a parameter extraction method based on a single bottom-gate/top-contact organic thin-film transistor

NASA Astrophysics Data System (ADS)

Takagaki, Shunsuke; Yamada, Hirofumi; Noda, Kei

2018-03-01

Contact effects in organic thin-film transistors (OTFTs) were examined by using our previously proposed parameter extraction method from the electrical characteristics of a single staggered-type device. Gate-voltage-dependent contact resistance and channel mobility in the linear regime were evaluated for bottom-gate/top-contact (BGTC) pentacene TFTs with active layers of different thicknesses, and for pentacene TFTs with contact-doped layers prepared by coevaporation of pentacene and tetrafluorotetracyanoquinodimethane (F4TCNQ). The extracted parameters suggested that the influence of the contact resistance becomes more prominent with the larger active-layer thickness, and that contact-doping experiments give rise to a drastic decrease in the contact resistance and a concurrent considerable improvement in the channel mobility. Additionally, the estimated energy distributions of trap density in the transistor channel probably reflect the trap filling with charge carriers injected into the channel regions. The analysis results in this study confirm the effectiveness of our proposed method, with which we can investigate contact effects and circumvent the influences of characteristic variations in OTFT fabrication.

Subperiosteal and intraosseous connective tissue grafts for pocket reduction: a 9- to 13-year retrospective case series report.

PubMed

Nelson, S W

2001-10-01

Recent histological evidence has documented that grafted palatal connective tissue is capable of forming a new attachment to previously exposed roots in the treatment of gingival recession. No clinical studies have tested the ability of connective tissue that has been implanted beneath the periosteum into periodontal osseous defects to reduce probing depth and increase clinical attachment levels. This study reports the long-term clinical effect of subperiosteal and intraosseous connective tissue grafts on deep periodontal pockets. Connective tissue (CT) grafts were placed in 32 periodontal pockets on 27 patients. Grafts were classified into 3 groups. Type I grafts had 50% or more vascular surface contact and were < or = 2.5 mm thick. Type II grafts had 50% or more contact but were > 2.5 mm thick, and Type III grafts had less than 50% vascular contact regardless of thickness. Twelve of 14 Type I sites, 9 of 15 Type II sites, and 3 of 3 Type III sites were analyzed 9 to 13 years following treatment. Clinical attachment level change differed significantly between the graft types on survivor teeth (P < 0.05): Type III had 2 mm loss (95% confidence interval [CI]: 0.4 to 3.6), while Type II and Type I grafts had a 2.7 mm gain (95% CI: 2.0 to 3.4) and 4.3 mm gain (95% CI: 3.3 to 5.2), respectively. Similar substantial differences were presented for changes in probing depth and recession. This long-term (9 to 13 years) retrospective case-series analysis suggests substantial improvements in periodontal clinical measures for Type I CT grafts in deep periodontal pockets. Randomized trials are required to evaluate this promising procedure.

Contact between the acetabulum and dome of a Kerboull-type plate influences the stress on the plate and screw.

PubMed

Hara, Katsutoshi; Kaku, Nobuhiro; Tabata, Tomonori; Tsumura, Hiroshi

2015-07-01

We used a three-dimensional finite element method to investigate the conditions behind the Kerboull-type (KT) dome. The KT plate dome was divided into five areas, and 14 models were created to examine different conditions of dome contact with the acetabulum. The maximum stress on the KT plate and screws was estimated for each model. Furthermore, to investigate the impact of the contact area with the acetabulum on the KT plate, a multiple regression analysis was conducted using the analysis results. The dome-acetabulum contact area affected the maximum equivalent stress on the KT plate; good contact with two specific areas of the vertical and horizontal beams (Areas 3 and 5) reduced the maximum equivalent stress. The maximum equivalent stress on the hook increased when the hardness of the bone representing the acetabulum varied. Thus, we confirmed the technical importance of providing a plate with a broad area of appropriate support from the bone and cement in the posterior portion of the dome and also proved the importance of supporting the area of the plate in the direction of the load at the center of the cross-plate and near the hook.

Evaluation of the occlusal contact of crowns fabricated with the bite impression method.

PubMed

Makino, Sachi; Okada, Daizo; Shin, Chiharu; Ogura, Reiko; Ikeda, Masaomi; Miura, Hiroyuki

2013-09-30

In prosthodontic treatment, reconstruction of a proper occlusal contact relationship is very important as well as reconstruction of a proper interproximal relationship and marginal fitness. Unfortunately, occlusal relationships are sometimes lost in the process of occlusal adjustment of crowns. The purpose of this study was to compare the occlusal contacts of single crown fabricated by two different types of impression techniques. Nine subjects, whose molars required treatment with crown restoration, were enrolled in this study. Full cast crowns were fabricated using two types of impression techniques: the conventional impression method (CIM) and the bite impression method (BIM). The occlusal contacts of crowns were precisely evaluated at the following stages: after occlusal adjustment on the articulator (Step 0), before occlusal adjustment in the mouth (Step 1), after occlusal adjustment at the intercuspal position (Step 2), and after occlusal adjustment during lateral and protrusive excursions (Step 3). The number of occlusal contacts of the crowns on the functional cusps fabricated with BIM was significantly greater than that with CIM after occlusal adjustment. For this reason, the crowns fabricated with BIM might have a more functionally desirable occlusal surface compared to the crowns fabricated with CIM.

Development of Non-contact Respiratory Monitoring System for Newborn Using a FG Vision Sensor

NASA Astrophysics Data System (ADS)

Kurami, Yoshiyuki; Itoh, Yushi; Natori, Michiya; Ohzeki, Kazuo; Aoki, Yoshimitsu

In recent years, development of neonatal care is strongly hoped, with increase of the low-birth-weight baby birth rate. Especially respiration of low-birth-weight baby is incertitude because central nerve and respiratory function is immature. Therefore, a low-birth-weight baby often causes a disease of respiration. In a NICU (Neonatal Intensive Care Unit), neonatal respiration is monitored using cardio-respiratory monitor and pulse oximeter at all times. These contact-type sensors can measure respiratory rate and SpO2 (Saturation of Peripheral Oxygen). However, because a contact-type sensor might damage the newborn's skin, it is a real burden to monitor neonatal respiration. Therefore, we developed the respiratory monitoring system for newborn using a FG (Fiber Grating) vision sensor. FG vision sensor is an active stereo vision sensor, it is possible for non-contact 3D measurement. A respiratory waveform is calculated by detecting the vertical motion of the thoracic and abdominal region with respiration. We attempted clinical experiment in the NICU, and confirmed the accuracy of the obtained respiratory waveform was high. Non-contact respiratory monitoring of newborn using a FG vision sensor enabled the minimally invasive procedure.

A Laboratory Assessment of Factors That Affect Bacterial Adhesion to Contact Lenses

PubMed Central

Dutta, Debarun; Willcox, Mark DP

2013-01-01

Adhesion of pathogenic microbes, particularly bacteria, to contact lenses is implicated in contact lens related microbial adverse events. Various in vitro conditions such as type of bacteria, the size of initial inoculum, contact lens material, nutritional content of media, and incubation period can influence bacterial adhesion to contact lenses and the current study investigated the effect of these conditions on bacterial adhesion to contact lenses. There was no significant difference in numbers of bacteria that adhered to hydrogel etafilcon A or silicone hydrogel senofilcon A contact lenses. Pseudomonas aeruginosa adhered in higher numbers compared to Staphylococcus aureus. Within a genera/species, adhesion of different bacterial strains did not differ appreciably. The size of initial inoculum, nutritional content of media, and incubation period played significant roles in bacterial adhesion to lenses. A set of in vitro assay conditions to help standardize adhesion between studies have been recommended. PMID:24833224

Controle orbital de satélites artificiais com propulsão e uso de gravidade lunar

NASA Astrophysics Data System (ADS)

Torres, K. S.; de Almeida Prado, A. F. B.

2003-08-01

A redução do custo de combustível de uma manobra é atualmente a grande prioridade de todos os programas espaciais existentes no mundo. As manobras assistidas pela gravidade são uma ótima forma de se contornar o problema pois proporcionam economias com vasto impacto no custo final da missão. Neste trabalho é feito um estudo particular do controle orbital de um satélite artificial da Terra usando a gravidade da Lua. O objetivo é estudar uma técnica econômica para uma mudança de plano de um satélite que está em órbita em volta da Terra. A idéia principal desta abordagem é enviar primeiramente o veículo espacial em direção à Lua usando uma manobra mono-impulsiva para que assim o campo gravitacional da Lua possa fazer a mudança de plano desejada (sem custo de combustível) e só então retornar o veículo aos valores iniciais de semi-eixo e excentricidade usando uma manobra bi-impulsiva tipo Hohmann. Para tanto, é assumido que a espaçonave inicia em uma órbita circular coplanar à órbita da lua em torno da Terra e a meta é colocá-la em uma órbita similar que difere da órbita inicial somente pela inclinação. São usadas equações analíticas baseadas na abordagem Patched Conics para se calcular a variação na velocidade, momento angular, energia e inclinação do veículo espacial que realiza esta manobra. Várias simulações são feitas para se avaliar as economias de combustível envolvidas.

An Orbital Period Study of the W UMa-Type Binary RZ Comae Berenicis

NASA Astrophysics Data System (ADS)

Qian, Sheng-Bang; He, Jia-Jia

2005-12-01

New photoelectric and CCD photometry observations of a short-period W UMa-type binary system, RZ Com, are presented. The light curves of Broglia (1960, Contr. Milano-Merate, 165) were symmetric in V band, while the present light curve shows a typical O'Connell effect, with Maximum I brighter than Maximum II by 0.015mag. It is found that the light curve of the binary star has changed from W-subtype to A-subtype according to Binnendijk's classification. This variation may be caused by the activity of dark spot on the primary component. Combining four newly determined times of the light minimum with others published in the literature, the orbital period change of the system was investigated. A small-amplitude oscillation (A = 0.0058 d), with a period of 44.8yr has been discovered to be superimposed on a long-term period increase with a rate of dP/dt = +4.12 × 10-8 d yr-1. The period oscillation can be explained either by the light-time effect via the presence of an unseen third body or by magnetic-activity cycles of the components. The mass ratio of RZ Com is q = 0.43. The secular period variation is in agreement with the conclusions of Qian (2001, MNRAS, 328, 914; 2003, MNRAS, 342, 1260). This indicates that it is on the TRO-controlled stage of the evolutionary scheme proposed by Qian.

Device for coupling a first vehicle to a second vehicle

NASA Technical Reports Server (NTRS)

Rudmann, A. A. (Inventor)

1980-01-01

A device is disclosed, carried by a first vehicle such as an orbiting space shuttle, having a plurality of contact members for engaging and holding an annular ring on a second vehicle such as an orbiting payload. The contact members are connected to manipulator arms which are mounted at a fulcrum point and which are moved by an iris type mechanism. Movement of the manipulator arms causes the contact members to grasp or release the annular ring. Bumper devices are provided to axially align the annular ring and draw the contact members into engagement therewith.

[Investigations on the tolerance and reliability of contact lenses in air and space travel (author's transl)].

PubMed

Draeger, J; Schröder, U; Vogt, L

1980-03-01

It is still forbidden by German law for cockpit aircrew to wear contact lenses. This is due in particular to experience gathered in the past with older types of contact lenses, especially those made of glass or PMMA. Meanwhile, technological progress has brought improvements in respect of material, size, tolerance and particularly the optical result. Investigations were carried out with regard to the tolerance of contact lenses in condition of low humidity, high g and sudden compression. The results are given and the consequences for cockpit aircrew and passengers are discussed.

A contact-force regulated photoplethysmography (PPG) platform

NASA Astrophysics Data System (ADS)

Sim, Jai Kyoung; Ahn, Bongyoung; Doh, Il

2018-04-01

A photoplethysmography (PPG) platform integrated with a miniaturized force-regulator is proposed in this study. Because a thermo-pneumatic type regulator maintains a consistent contact-force between the PPG probe and the measuring site, a consistent and stable PPG signal can be obtained. We designed and fabricated a watch-type PPG platform with an overall size of 35 mm × 19 mm. In the PPG measurement on the radial artery wrist while posture of the wrist is changed to extension, neutral, or flexion, regulation of the contact-force provides consistent PPG measurements for which the variations in the PPG amplitude (PPGA) was 7.2 %. The proposed PPG platform can be applied to biosignal measurements in various fields such as PPG-based ANS monitoring to estimate nociception, sleep apnea syndrome, and psychological stress.

Physical Parameters of Components in Close Binary Systems: IV

NASA Astrophysics Data System (ADS)

Gazeas, K. D.; Baran, A.; Niarchos, P.; Zola, S.; Kreiner, J. M.; Ogloza, W.; Rucinski, S. M.; Zakrzewski, B.; Siwak, M.; Pigulski, A.; Drozdz, M.

2005-03-01

The paper presents new geometric, photometric and absolute parameters, derived from combined spectroscopic and photometric solutions, for ten contact binary systems. The analysis shows that three systems (EF Boo, GM Dra and SW Lac) are of W-type with shallow to moderate contact. Seven systems (V417 Aql, AH Aur, YY CrB, UX Eri, DZ Psc, GR Vir and NN Vir) are of A-type in a deep contact configuration. For six systems (V417 Aql, YY CrB, GM Dra, UX Eri, SW Lac and GR Vir) a spot model is introduced to explain the O'Connell effect in their light curves. The photometric and geometric elements of the systems are combined with the spectroscopic data taken at David Dunlap Observatory to yield the absolute parameters of the components.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samec, R. G.; Melton, R. A.; Figg, E. R.

GSC 3355 0394 has an EB-type light curve, which is dominated by hot and cool spot activities. It displays night-to-night variations in light-curve shapes. The period study yields six new times of minimum light and the first precision ephemeris, HJD T{sub min}I = 2, 454, 408.9547 {+-} 0.0017 + 0.4621603 {+-} 0.0000008d*E. VR{sub c}I{sub c} standard magnitudes are presented. BVRI Wilson synthetic light-curve solutions are calculated for both a Mode 4 (V1010 Oph-type, semidetached, more massive component filling its Roche lobe) configuration and a Mode 3, contact configuration (fill-out 100% or critical contact). The critical contact is the lowest residualmore » solution. Four major spot regions are needed to model this binary, at least one is evidently a stream spot.« less

Low p-type contact resistance by field-emission tunneling in highly Mg-doped GaN

NASA Astrophysics Data System (ADS)

Okumura, Hironori; Martin, Denis; Grandjean, Nicolas

2016-12-01

Mg-doped GaN with a net acceptor concentration (NA-ND) in the high 1019 cm-3 range was grown using ammonia molecular-beam epitaxy. Electrical properties of NiO contact on this heavily doped p-type GaN were investigated. A potential-barrier height of 0.24 eV was extracted from the relationship between NA-ND and the specific contact resistivity (ρc). We found that there is an optimum NA-ND value of 5 × 1019 cm-3 for which ρc is as low as 2 × 10-5 Ω cm2. This low ρc is ascribed to hole tunneling through the potential barrier at the NiO/p+-GaN interface, which is well accounted for by the field-emission model.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, David L.; Lee, Benjamin G.; Fogel, Derek

Here, we form gallium-doped poly-Si:Ga/SiO 2 passivated contacts on n-type Czochralski (n-Cz) wafers using ion implantation of Ga and Ga-containing spin-on dopants. After annealing and passivation with Al 2O 3, the contacts exhibit i Voc values of >730 mV with corresponding Joe values of <5 fA/cm 2. These are among the best-reported values for p-type poly-Si/SiO 2 contacts. Secondary ion mass spectroscopic depth profile data show that, in contrast to B, Ga does not pileup at the SiO 2 interface in agreement with its known high diffusivity in SiO 2. This lack of Ga pileup may imply fewer dopant-related defectsmore » in the SiO 2, compared with B dopants, and account for the excellent passivation.« less

Power profiles and short-term visual performance of soft contact lenses.

PubMed

Papas, Eric; Dahms, Anne; Carnt, Nicole; Tahhan, Nina; Ehrmann, Klaus

2009-04-01

To investigate the manner in which contemporary soft contact lenses differ in the distribution of optical power within their optic zones and establish if these variations affect the vision of wearers or the prescribing procedure for back vertex power (BVP). By using a Visionix VC 2001 contact lens power analyzer, power profiles were measured across the optic zones of the following contemporary contact lenses ACUVUE 2, ACUVUE ADVANCE, O2OPTIX, NIGHT & DAY and PureVision. Single BVP measures were obtained using a Nikon projection lensometer. Visual performance was assessed in 28 masked subjects who wore each lens type in random order. Measurements taken were high and low contrast visual acuity in normal illumination (250 Cd/m), high contrast acuity in reduced illumination (5 Cd/m), subjective visual quality using a numerical rating scale, and visual satisfaction rating using a Likert scale. Marked differences in the distribution of optical power across the optic zone were evident among the lens types. No significant differences were found for any of the visual performance variables (p > 0.05, analysis of variance with repeated measures and Friedman test). Variations in power profile between contemporary soft lens types exist but do not, in general, result in measurable visual performance differences in the short term, nor do they substantially influence the BVP required for optimal correction.

Tunnel-injected sub 290 nm ultra-violet light emitting diodes with 2.8% external quantum efficiency

NASA Astrophysics Data System (ADS)

Zhang, Yuewei; Jamal-Eddine, Zane; Akyol, Fatih; Bajaj, Sanyam; Johnson, Jared M.; Calderon, Gabriel; Allerman, Andrew A.; Moseley, Michael W.; Armstrong, Andrew M.; Hwang, Jinwoo; Rajan, Siddharth

2018-02-01

We report on the high efficiency tunnel-injected ultraviolet light emitting diodes (UV LEDs) emitting at 287 nm. Deep UV LED performance has been limited by the severe internal light absorption in the p-type contact layers and low electrical injection efficiency due to poor p-type conduction. In this work, a polarization engineered Al0.65Ga0.35N/In0.2Ga0.8N tunnel junction layer is adopted for non-equilibrium hole injection to replace the conventionally used direct p-type contact. A reverse-graded AlGaN contact layer is further introduced to realize a low resistance contact to the top n-AlGaN layer. This led to the demonstration of a low tunnel junction resistance of 1.9 × 10-3 Ω cm2 obtained at 1 kA/cm2. Light emission at 287 nm with an on-wafer peak external quantum efficiency of 2.8% and a wall-plug efficiency of 1.1% was achieved. The measured power density at 1 kA/cm2 was 54.4 W/cm2, confirming the efficient hole injection through interband tunneling. With the benefits of the minimized internal absorption and efficient hole injection, a tunnel-injected UV LED structure could enable future high efficiency UV emitters.

Estrogenic activities of chemicals related to food contact plastics and rubbers tested by the yeast two-hybrid assay.

PubMed

Ogawa, Yuko; Kawamura, Yoko; Wakui, Chiseko; Mutsuga, Motoh; Nishimura, Tetsuji; Tanamoto, Kenichi

2006-04-01

Food contact plastics and rubbers possibly contain many kinds of chemicals such as monomers, oligomers, additives, degradation products of polymers and additives, and impurities. Among them, bisphenol A, nonylphenol, benzylbutyl phthalate, styrene oligomers and hydroxylated benzophenones have been reported to possess estrogenic activities. In this study, other chemicals related to food contact plastics and rubbers, and their metabolites induced by the S9-mixture were tested for their estrogenic activities using the yeast two-hybrid assay. Among the 150 chemicals, 10 chemicals such as bis(4-hydroxyphenyl) methane, 4-cyclohexylphenol, 4-phenylphenol, 4,4'-isopropylidenediphenol alkylphosphite, two type of styrenated phenol (including mono type), tris(nonylphenyl) phosphite, 2,2'-dihydroxy-4-methoxybenzophenone, 2-hydroxy-4-methoxybenzophenone and 2,4-diphenyl-4-methyl-1-pentene, their metabolites and the metabolites of 6 other chemicals, such as 2-(phenylmethyl) phenol, styrenated phenol (di and tri type), 1-(N-phenylamino)naphthalene, 4-tert-butylphenylsalicylate, nonylphenol ethoxylates and 2-methyl-6-tert-butylphenol, displayed estrogenic activities. All of them contained a phenol group in their chemical structures or formed one easily by hydrolysis or metabolism. However, most of the chemicals related to food contact plastics and rubbers, and their metabolites did not show any estrogenicity.

76 FR 22680 - Procurement List; Proposed Addition

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-22

... (41 U.S.C. 46- 48c) in connection with the service proposed for addition to the Procurement List... Type/Location: Contact Center Service. Human Resources Command Contact Center, Fort Knox, KY. NPAs...). Contracting Activity: Department of the Army, Human Resource Command, Fort Knox, KY. Barry S. Lineback...

78 FR 13882 - Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-01

... site, http://nac.samhsa.gov/ , or by contacting Crystal C. Saunders, Acting Designated Federal Official.... Date/Time/Type: April 10, 2013, 9:00 a.m.-5:30 p.m. EST: (OPEN). Place: SAMHSA Building, Sugarloaf Conference Room. Contact: Crystal C. Saunders, Acting, Designated Federal Official, SAMHSA, CMHS, National...

77 FR 46444 - Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-03

... meeting by accessing the SAMHSA Committee Web site, http://nac.samhsa.gov/ , or by contacting Crystal C... Services National Advisory Council. Date/Time/Type: August 16, 2012, 8:30-5:00 (OPEN). Place: Live meeting webcast. Contact: Crystal C. Saunders, Acting Designated Federal Official, SAMHSA, Center for Mental...

78 FR 49527 - Agency Information Collection Activities; Submission for Office of Management and Budget Review...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-14

...: Submitter type, company name, address, country, company headquarters Dun and Bradstreet number, and company headquarters Facility Establishment Identifier number; Submitter point of contact: Contact name, title... and signature of submitter including name, company name, address, position title, email, telephone...

High-performance multilayer WSe 2 field-effect transistors with carrier type control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pudasaini, Pushpa Raj; Oyedele, Akinola; Zhang, Cheng

In this paper, high-performance multilayer WSe 2 field-effect transistor (FET) devices with carrier type control are demonstrated via thickness modulation and a remote oxygen plasma surface treatment. Carrier type control in multilayer WSe 2 FET devices with Cr/Au contacts is initially demonstrated by modulating the WSe 2 thickness. The carrier type evolves with increasing WSe 2 channel thickness, being p-type, ambipolar, and n-type at thicknesses <3, ~4, and >5 nm, respectively. The thickness-dependent carrier type is attributed to changes in the bandgap of WSe 2 as a function of the thickness and the carrier band offsets relative to the metalmore » contacts. Furthermore, we present a strong hole carrier doping effect via remote oxygen plasma treatment. It non-degenerately converts n-type characteristics into p-type and enhances field-effect hole mobility by three orders of magnitude. Finally, this work demonstrates progress towards the realization of high-performance multilayer WSe 2 FETs with carrier type control, potentially extendable to other transition metal dichalcogenides, for future electronic and optoelectronic applications.« less

High-performance multilayer WSe 2 field-effect transistors with carrier type control

DOE PAGES

Pudasaini, Pushpa Raj; Oyedele, Akinola; Zhang, Cheng; ...

2017-07-06

In this paper, high-performance multilayer WSe 2 field-effect transistor (FET) devices with carrier type control are demonstrated via thickness modulation and a remote oxygen plasma surface treatment. Carrier type control in multilayer WSe 2 FET devices with Cr/Au contacts is initially demonstrated by modulating the WSe 2 thickness. The carrier type evolves with increasing WSe 2 channel thickness, being p-type, ambipolar, and n-type at thicknesses <3, ~4, and >5 nm, respectively. The thickness-dependent carrier type is attributed to changes in the bandgap of WSe 2 as a function of the thickness and the carrier band offsets relative to the metalmore » contacts. Furthermore, we present a strong hole carrier doping effect via remote oxygen plasma treatment. It non-degenerately converts n-type characteristics into p-type and enhances field-effect hole mobility by three orders of magnitude. Finally, this work demonstrates progress towards the realization of high-performance multilayer WSe 2 FETs with carrier type control, potentially extendable to other transition metal dichalcogenides, for future electronic and optoelectronic applications.« less

Power Profiles of Commercial Multifocal Soft Contact Lenses.

PubMed

Kim, Eon; Bakaraju, Ravi C; Ehrmann, Klaus

2017-02-01

To evaluate the optical power profiles of commercially available soft multifocal contact lenses and compare their optical designs. The power profiles of 38 types of multifocal contact lenses-three lenses each-were measured in powers +6D, +3D, +1D, -1D, -3D, and -6D using NIMO TR1504 (Lambda-X, Belgium). All lenses were measured in phosphate buffered saline across 8 mm optic zone diameter. Refractive index of each lens material was measured using CLR 12-70 (Index Instruments, UK), which was used for converting measured power in the medium to in-air radial power profiles. Three basic types of power profiles were identified: center-near, center-distance, and concentric-zone ring-type designs. For most of the lens types, the relative plus with respect to prescription power was lower than the corresponding spectacle add. For some lens types, the measured power profiles were shifted by up to 1D across the power range relative to their labeled power. Most of the lenses were designed with noticeable amounts of spherical aberration. The sign and magnitude of spherical aberration can either be power dependent or consistent across the power range. Power profiles can vary widely between the different lens types; however, certain similarities were also observed between some of the center-near designs. For the more recently released lens types, there seems to be a trend emerging to reduce the relative plus with respect to prescription power, include negative spherical aberration, and keep the power profiles consistent across the power range.

High performance MoS2 TFT using graphene contact first process

NASA Astrophysics Data System (ADS)

Chang Chien, Chih-Shiang; Chang, Hsun-Ming; Lee, Wei-Ta; Tang, Ming-Ru; Wu, Chao-Hsin; Lee, Si-Chen

2017-08-01

An ohmic contact of graphene/MoS2 heterostructure is determined by using ultraviolet photoelectron spectroscopy (UPS). Since graphene shows a great potential to replace metal contact, a direct comparison of Cr/Au contact and graphene contact on the MoS2 thin film transistor (TFT) is made. Different from metal contacts, the work function of graphene can be modulated. As a result, the subthreshold swing can be improved. And when Vg

Droplet sliding on inclined superhydrophobic surfaces: the effect of anisotropic contact line

NASA Astrophysics Data System (ADS)

Jiang, Youhua; Cao, Lile; Guo, Zongqi; Choi, Chang-Hwan

2017-11-01

Although the effects of solid structures on droplet retention on superhydrophobic surfaces have been studied extensively, the investigation has been restricted to the sessile droplets on horizontal surfaces where the contact line motions are axisymmetric or isotropic (either advancing or receding). In the droplet retention on inclined surfaces, the contact line motions are asymmetric or anisotropic; the advancing and receding motions coexist. In this study, we investigate the correlation between the droplet boundary pinning and the surface morphology on inclined superhydrophobic surfaces. The evolution of the droplet contact angle and width show contrary behaviors between pillar- and pore-structured surfaces due to the distinctive microscopic contact line motions. Therefore, the visualizations of the contact line motions at different locations of the boundary on inclined superhydrophobic surfaces are performed and the averaged contact line density of the boundary is quantified. The result shows that the droplet retentive force monotonously increase with the increase in contact line density, regardless of the surface morphological types, dimensions, or the direction of contact line motion (advancing, receding, or both). The result indicates that the droplet retentive force on superhydrophobic surfaces is mainly determined by the contact line density, regardless of the isotropy of the contact line.

A highly accurate dynamic contact angle algorithm for drops on inclined surface based on ellipse-fitting.

PubMed

Xu, Z N; Wang, S Y

2015-02-01

To improve the accuracy in the calculation of dynamic contact angle for drops on the inclined surface, a significant number of numerical drop profiles on the inclined surface with different inclination angles, drop volumes, and contact angles are generated based on the finite difference method, a least-squares ellipse-fitting algorithm is used to calculate the dynamic contact angle. The influences of the above three factors are systematically investigated. The results reveal that the dynamic contact angle errors, including the errors of the left and right contact angles, evaluated by the ellipse-fitting algorithm tend to increase with inclination angle/drop volume/contact angle. If the drop volume and the solid substrate are fixed, the errors of the left and right contact angles increase with inclination angle. After performing a tremendous amount of computation, the critical dimensionless drop volumes corresponding to the critical contact angle error are obtained. Based on the values of the critical volumes, a highly accurate dynamic contact angle algorithm is proposed and fully validated. Within nearly the whole hydrophobicity range, it can decrease the dynamic contact angle error in the inclined plane method to less than a certain value even for different types of liquids.

Ferrographic analysis of wear debris generated in a sliding elastohydrodynamic contact

NASA Technical Reports Server (NTRS)

Jones, W. R., Jr.; Nagaraj, H. S.; Winer, W. O.

1977-01-01

The ferrograph was used to analyze wear debris generated in a sliding elastohydrodynamic contact. The amount of wear debris correlates well with the ratio of film thickness to composite surface roughness. Essentially all of the generated wear particles were of the normal rubbing wear type.

FEASIBILITY STUDY OF AIR BEARING ROCKET SLED SLIPPERS

DTIC Science & Technology

a simple self-acting type of bearing can support a typical monorail rocket sled, without contact between the slipper and the rail, at speeds between...slipper bearing is capable of preventing slipper-rail contact over the entire speed range of typical monorail and dual rail sleds. However, the weight and

Atrial rhythm influences catheter tissue contact during radiofrequency catheter ablation of atrial fibrillation: comparison of contact force between sinus rhythm and atrial fibrillation.

PubMed

Matsuda, Hisao; Parwani, Abdul Shokor; Attanasio, Philipp; Huemer, Martin; Wutzler, Alexander; Blaschke, Florian; Haverkamp, Wilhelm; Boldt, Leif-Hendrik

2016-09-01

Catheter tissue contact force (CF) is an important factor for durable lesion formation during radiofrequency catheter ablation (RFCA) of atrial fibrillation (AF). Since CF varies in the beating heart, atrial rhythm during RFCA may influence CF. A high-density map and RFCA points were obtained in 25 patients undergoing RFCA of AF using a CF-sensing catheter (Tacticath, St. Jude Medical). The operators were blinded to the CF information. Contact type was classified into three categories: constant, variable, and intermittent contact. Average CF and contact type were analyzed according to atrial rhythm (SR vs. AF) and anatomical location. A total of 1364 points (891 points during SR and 473 points during AF) were analyzed. Average CFs showed no significant difference between SR (17.2 ± 11.3 g) and AF (17.2 ± 13.3 g; p = 0.99). The distribution of points with an average CF of ≥20 and <10 g also showed no significant difference. However, the distribution of excessive CF (CF ≥40 g) was significantly higher during AF (7.4 %) in comparison with SR (4.2 %; p < 0.05). At the anterior area of the right inferior pulmonary vein (RIPV), the average CF during AF was significantly higher than during SR (p < 0.05). Constant contact was significantly higher during AF (32.2 %) when compared to SR (9.9 %; p < 0.01). Although the average CF was not different between atrial rhythms, constant contact was more often achievable during AF than it was during SR. However, excessive CF also seems to occur more frequently during AF especially at the anterior part of RIPV.

Descriptive study of enteric zoonoses in Ontario, Canada, from 2010 - 2012.

PubMed

Whitfield, Yvonne; Johnson, Karen; Hobbs, Leigh; Middleton, Dean; Dhar, Badal; Vrbova, Linda

2017-02-21

Contact with animals and their environment has long been recognized as an important source of enteric zoonoses. However, there are limited data available on the burden of illness associated with specific types of animals in Canada. This study describes the overall burden of enteric zoonoses in Ontario, Canada from 2010 to 2012. Confirmed cases of seven enteric zoonotic diseases (campylobacteriosis, cryptosporidiosis, giardiasis, listeriosis, salmonellosis, verotoxin-producing E. coli (VTEC) infection, and yersiniosis) with episode dates from 2010 to 2012 were extracted from the integrated Public Health Information System (iPHIS). Reported exposures were categorized as animal contact, foodborne, waterborne and 'other', with animal contact grouped into nine sub-categories based on the type of animal or transmission setting. Overall incidence rates and proportions by animal exposure categories, age and sex-specific incidence rates and hospitalization and death proportions were calculated and sex proportions compared. Our study found that approximately 26% of the enteric pathogens assessed during the 2010 to 2012 period reported contact with animals and their environments as the mode of transmission. Of enteric disease cases reporting animal contact, farm exposures were reported for 51.3%, dog or cat exposures for 26.3%, and reptile or amphibian exposures for 8.9%. Contact with animals was reported more frequently during the period 2010 to 2012 in comparison to the period 1997 to 2003 when 6% or less of enteric cases were associated with animal contact. Public health professionals, stakeholders associated with animals and their related industries (e.g., pet treats, mobile zoos, abattoirs), and the public should recognize that animal contact is an important source of enteric illnesses in order to take measures to reduce the burden of illness from animal sources.

Development of technologies for welding interconnects to fifty-micron thick silicon solar cells

NASA Technical Reports Server (NTRS)

Patterson, R. E.

1982-01-01

A program was conducted to develop technologies for welding interconnects to 50 microns thick, 2 by 2 cm solar cells. The cells were characterized with respect to electrical performance, cell thickness, silver contact thickness, contact waviness, bowing, and fracture strength. Weld schedules were independently developed for each of the three cell types and were coincidentally identical. Thermal shock tests (100 cycles from 100 C to -180 C) were performed on 16 cell coupons for each cell type without any weld joint failures or electrical degradation. Three 48 cell modules (one for each cell type) were assembled with 50 microns thick cells, frosted fused silica covers, silver clad Invar interconnectors, and Kapton substrates.

Welding interconnects to 50-micron silicon solar cells

NASA Technical Reports Server (NTRS)

Patterson, R. E.; Mesch, H. G.

1983-01-01

A program was conducted to develop technologies for welding interconnects to 50-micron thick, 2 by 2 cm solar cells obtained from three suppliers. The cells were characterized with respect to electrical performance, cell thickness, silver contact thickness, contact waviness, bowing, and fracture strength. Weld schedules were independently developed for each of the three cell types and were coincidentally identical. Thermal shock tests (100 cycles from 100 deg to -180 deg C) were performed on 16-cell coupons for each cell type without any weld joint failures or electrical degradation. Three 48-cell modules (one for each cell type) were assembled with 50-micron thick cells, frosted fused silica covers, silver clad Invar interconnectors, and Kapton substrates.

Spin injection and detection in lateral spin valves with hybrid interfaces

NASA Astrophysics Data System (ADS)

Wang, Le; Liu, Wenyu; Ying, Hao; Chen, Luchen; Lu, Zhanjie; Han, Shuo; Chen, Shanshan; Zhao, Bing; Xu, Xiaoguang; Jiang, Yong

2018-06-01

Spin injection and detection in lateral spin valves with hybrid interfaces comprising a Co/Ag transparent contact and a Co/MgO/Ag junction (III) are investigated at room temperature in comparison with pure Co/Ag transparent contacts (I) and Co/MgO/Ag junctions (II). The measured spin-accumulation signals of a type III device are five times higher than those for type I. The extracted spin diffusion length in Ag is 180 nm for all three types of devices. The enhancement of the spin signal of the hybrid structure is mainly attributed to the increase of the interfacial spin polarization from the Co/MgO/Ag junction.

Tyre contact length on dry and wet road surfaces measured by three-axial accelerometer

NASA Astrophysics Data System (ADS)

Matilainen, Mika; Tuononen, Ari

2015-02-01

We determined the tyre contact length on dry and wet roads by measuring the accelerations of the inner liner with a three-axial accelerometer. The influence of the tyre pressure, driving velocity, and tread depth on the contact length was studied in both types of road surface conditions. On dry asphalt the contact length was almost constant, regardless of the driving velocity. On wet asphalt the presence of water could be detected even at low driving velocities (e.g. 20 km/h for a worn tyre) as the contact length began to decrease from that found in the dry asphalt situation. In addition to improving the performance of active safety systems and driver warning systems, the contact length information could be beneficial for classifying and studying the aquaplaning behaviour of tyres.

Examining the role of Scotland's telephone advice service (NHS 24) for managing health in the community: analysis of routinely collected NHS 24 data

PubMed Central

Elliott, Alison M; McAteer, Anne; Heaney, David; Ritchie, Lewis D; Hannaford, Philip C

2015-01-01

Objectives To examine the type, duration and outcome of the symptoms and health problems Scotland's nurse-led telephone advice service (NHS 24) is contacted about and explore whether these vary by time of contact and patient characteristics. Design Analysis of routinely collected NHS 24 data. Setting Scotland, UK. Participants Users of NHS 24 during 2011. Main outcome measures Proportion of the type, duration and outcome of the symptoms and health problems NHS 24 is contacted about. Results 82.6% of the calls were made out-of-hours and 17.4% in-hours. Abdominal problems accounted for the largest proportion of calls (12.2%) followed by dental (6.8%) and rash/skin problems (6.0%). There were differences in the type of problems presented in-hours and out-of-hours. Most problems (62.9%) had lasted <24 h before people contacted NHS 24. Out-of-hours calls tended to be for problems of shorter duration. Problems reported out-of-hours most commonly resulted in advice to visit an out-of-hours centre and in-hours advice to contact a general practitioner. Most of the service users were female and from more affluent areas. Use of the service declined with age in those over 35 years. The characteristics of users varied according to when NHS 24 was contacted. The number of calls made by an individual in the year ranged from 1 to 866, although most users (69.2%) made only one call. The type of problem presented varied by age and deprivation, but was broadly similar by gender, rural/urban status and geographic area. Call outcomes also varied by user characteristics. Conclusions This is the first study to examine how the public uses NHS 24. It has identified the patterns of problems which the service must be equipped to deal with. It has also provided important information about who uses the service and when. This information will help future planning and development of the service. PMID:26310396

Characterization of very-long-period seismicity accompanying summit activity at Kīlauea Volcano, Hawai'i: 2007-2013

USGS Publications Warehouse

Dawson, Phillip; Chouet, Bernard

2014-01-01

Eruptive activity returned to the summit region of Kīlauea Volcano, Hawai'i with the formation of the “Overlook crater” within the Halema'uma'u Crater in March 2008. The new crater continued to grow through episodic collapse of the crater walls and as of late 2013 had grown into an approximately elliptical opening with dimensions of ~ 160 × 215 m extending to a depth of ~ 200 m. Occasional weak explosive events and a persistent gas plume continued to occur through 2013. Lava was first observed in the new crater in September 2008, and through 2009 the lava level remained deep in the crater and was only occasionally observed. Since early 2010 a lava lake with fluctuating level within the Overlook crater has been nearly continuously present, and has reached to within 22 m of the Overlook crater rim. Volcanic activity at Kīlauea Volcano is episodic at all time scales and the characterization of very-long-period seismicity in the band 2–100 s for the years 2007–2013 illuminates a portion of this broad spectrum of volcanic behavior. Three types of very-long-period events have been observed over this time and each is associated with distinct processes. Type 1 events are associated with vigorous degassing and occurred primarily between 2007 and 2009. Type 2 events are associated with rockfalls onto the lava lake and occurred primarily after early 2010. Both of these event types are induced by pressure and momentum changes at the top of the magma column that are transmitted downward to a source centroid ~ 1 km below the northeast corner of the Halema'uma'u Crater where the energy couples to the solid Earth at a geometrical discontinuity in the underlying dike system. Type 3 events are not related to surficial phenomena but are associated with transients in mass transfer that occur within the dike system. Very-long-period tremor has also accompanied the return of eruptive activity, with increasing amplitude associated with hours- to months-long changes in gas emission rates and summit deformation.

Novel Contact Materials for Improved Performance CdTe Solar Cells Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rockett, Angus; Marsillac, Sylvain; Collins, Robert

This program has explored a number of novel materials for contacts to CdTe solar cells in order to reduce the back contact Schottky barrier to zero and produce an ohmic contact. The project tested a wide range of potential contact materials including TiN, ZrN, CuInSe 2:N, a-Si:H and alloys with C, and FeS2. Improved contacts were achieved with FeS 2. As part of understanding the operation of the devices and controlling the deposition processes, a number of other important results were obtained. In the process of this project and following its conclusion it led to research that resulted in sevenmore » journal articles, nine conference publications, 13 talks presented at conferences, and training of eight graduate students. The seven journal articles were published in 2015, 2016, and 2017 and have been cited, as of March 2018, 52 times (one cited 19 times and two cited 11 times). We demonstrated high levels of doping of CIS with N but electrical activity of the resulting N was not high and the results were difficult to reproduce. Furthermore, even with high doping the contacts were not good. Annealing did not improve the contacts. A-Si:H was found to produce acceptable but unstable contacts, degrading even over a day or two, apparently due to H incorporation into the CdTe. Alloying with C did not improve the contacts or stability. The transition metal nitrides produced Schottky type contacts for all materials tested. While these contacts were found to be unsatisfactory, we investigated FeS 2 and found this material to be effective and comparable to the best contacts currently available. The contacts were found to be chemically stable under heat treatment and preferable to Cu doped contacts. Thus, we demonstrated an improved contact material in the course of this project. In addition, we developed new ways of controlling the deposition of CdTe and other materials, demonstrated the nature of defects in CdTe, and studied the distribution of conductivity and carrier type in CdTe devices. We demonstrated the conduction mechanism by which CdTe polycrystals improve the performance of the devices relative to single crystal devices. The mechanism shows that grain boundaries are conduction pathways for photogenerated electrons and that the corresponding holes are confined to the grains and therefore do not contribute to recombination.« less

Design, Generation and Tooth Contact Analysis (TCA) of Asymmetric Face Gear Drive With Modified Geometry

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Fuentes, Alfonso; Hawkins, J. M.; Handschuh, Robert F.

2001-01-01

A new type of face gear drive for application in transmissions, particularly in helicopters, has been developed. The new geometry differs from the existing geometry by application of asymmetric profiles and double-crowned pinion of the face gear mesh. The paper describes the computerized design, simulation of meshing and contact, and stress analysis by finite element method. Special purpose computer codes have been developed to conduct the analysis. The analysis of this new type of face gear is illustrated with a numerical example.

Ferrographic analysis of wear debris generated in accelerated rolling element fatigue tests

NASA Technical Reports Server (NTRS)

Jones, W. R., Jr.; Parker, R. J.

1977-01-01

Ferrographic analysis was used to determine the types and quantities of wear particles generated during accelerated rolling contact fatigue tests. The NASA five-ball rolling contact fatigue tester was used. Ball specimens were made of AMS 5749, a corrosion-resistant high-temperature bearing steel. The lubricant was a super-refined naphthenic mineral oil. Conditions included a maximum Hertz stress of 5.52 billion Pa and a shaft speed of 10,000 rpm. Four types of wear particles were observed: normal rubbing wear particles, fatigue spall particles, spheres, and friction polymer.

Back contact buffer layer for thin-film solar cells

DOEpatents

Compaan, Alvin D.; Plotnikov, Victor V.

2014-09-09

A photovoltaic cell structure is disclosed that includes a buffer/passivation layer at a CdTe/Back contact interface. The buffer/passivation layer is formed from the same material that forms the n-type semiconductor active layer. In one embodiment, the buffer layer and the n-type semiconductor active layer are formed from cadmium sulfide (CdS). A method of forming a photovoltaic cell includes the step of forming the semiconductor active layers and the buffer/passivation layer within the same deposition chamber and using the same material source.

Young children's contact with the elderly.

PubMed

Sheehan, R

1978-07-01

The present research is an investigation of the frequency and type of contact which young children have had with elderly persons. It is also an examination of the relationship between this contact and children's ability to identify or discriminate elderly persons. Interview data were gathered from children's parents pertaining to experiences which the children had with persons 70 years or older. The same children were also exposed to a series of stimulus discrimination tasks in which they were asked to identify the oldest man from a range of pictures. The research yielded descriptive data pertaining to the contact which children have with the elderly. It also revealed a statistically significant relationship between children's frequency of contact with elderly persons and their ability to identify the elderly.

Electron transport in extended carbon-nanotube/metal contacts: Ab initio based Green function method

NASA Astrophysics Data System (ADS)

Fediai, Artem; Ryndyk, Dmitry A.; Cuniberti, Gianaurelio

2015-04-01

We have developed a new method that is able to predict the electrical properties of the source and drain contacts in realistic carbon nanotube field effect transistors (CNTFETs). It is based on large-scale ab initio calculations combined with a Green function approach. For the first time, both internal and external parts of a realistic CNT-metal contact are taken into account at the ab initio level. We have developed the procedure allowing direct calculation of the self-energy for an extended contact. Within the method, it is possible to calculate the transmission coefficient through a contact of both finite and infinite length; the local density of states can be determined in both free and embedded CNT segments. We found perfect agreement with the experimental data for Pd and Al contacts. We have explained why CNTFETs with Pd electrodes are p -type FETs with ohmic contacts, which can carry current close to the ballistic limit (provided contact length is large enough), whereas in CNT-Al contacts transmission is suppressed to a significant extent, especially for holes.

Selective Requirement for Maintenance of Synaptic Contacts onto Motoneurons by Target-Derived trkB Receptors

PubMed Central

2016-01-01

Synaptic contacts onto motoneurons were studied in mice in which the gene for the trkB neurotrophin receptor was knocked out selectively in a subset of spinal motoneurons. The extent of contacts by structures immunoreactive for either of two different vesicular glutamate transporters (VGLUT1 and VGLUT2), the vesicular GABA transporter, or glutamic acid decarboxylase 67 (GAD67) with the somata of motoneurons, was studied in wild type and trkB knockout cells in tamoxifen treated male and female SLICK-trkB−/− mice. Selective knockout of the trkB gene resulted in a marked reduction in contacts made by VGLUT2- and GAD67-immunoreactive structures in both sexes and a significant reduction in contacts containing only glycine in male mice. No reduction was found for glycinergic contacts in female mice or for VGLUT1 immunoreactive contacts in either sex. Signaling through postsynaptic trkB receptors is considered to be an essential part of a cellular mechanism for maintaining the contacts of some, but not all, synaptic contacts onto motoneurons. PMID:27433358

Towards an optimal contact metal for CNTFETs.

PubMed

Fediai, Artem; Ryndyk, Dmitry A; Seifert, Gotthard; Mothes, Sven; Claus, Martin; Schröter, Michael; Cuniberti, Gianaurelio

2016-05-21

Downscaling of the contact length Lc of a side-contacted carbon nanotube field-effect transistor (CNTFET) is challenging because of the rapidly increasing contact resistance as Lc falls below 20-50 nm. If in agreement with existing experimental results, theoretical work might answer the question, which metals yield the lowest CNT-metal contact resistance and what physical mechanisms govern the geometry dependence of the contact resistance. However, at the scale of 10 nm, parameter-free models of electron transport become computationally prohibitively expensive. In our work we used a dedicated combination of the Green function formalism and density functional theory to perform an overall ab initio simulation of extended CNT-metal contacts of an arbitrary length (including infinite), a previously not achievable level of simulations. We provide a systematic and comprehensive discussion of metal-CNT contact properties as a function of the metal type and the contact length. We have found and been able to explain very uncommon relations between chemical, physical and electrical properties observed in CNT-metal contacts. The calculated electrical characteristics are in reasonable quantitative agreement and exhibit similar trends as the latest experimental data in terms of: (i) contact resistance for Lc = ∞, (ii) scaling of contact resistance Rc(Lc); (iii) metal-defined polarity of a CNTFET. Our results can guide technology development and contact material selection for downscaling the length of side-contacts below 10 nm.

Optimization of Ionic Liquid Based Simultaneous Ultrasonic- and Microwave-Assisted Extraction of Rutin and Quercetin from Leaves of Velvetleaf (Abutilon theophrasti) by Response Surface Methodology

PubMed Central

Zhao, Chunjian; Lu, Zhicheng; He, Xin; Li, Zhao; Shi, Kunming; Yang, Lei; Fu, Yujie; Zu, Yuangang

2014-01-01

An ionic liquids based simultaneous ultrasonic and microwave assisted extraction (ILs-UMAE) method has been proposed for the extraction of rutin (RU), quercetin (QU), from velvetleaf leaves. The influential parameters of the ILs-UMAE were optimized by the single factor and the central composite design (CCD) experiments. A 2.00 M 1-butyl-3-methylimidazolium bromide ([C4mim]Br) was used as the experimental ionic liquid, extraction temperature 60°C, extraction time 12 min, liquid-solid ratio 32 mL/g, microwave power of 534 W, and a fixed ultrasonic power of 50 W. Compared to conventional heating reflux extraction (HRE), the RU and QU extraction yields obtained by ILs-UMAE were, respectively, 5.49 mg/g and 0.27 mg/g, which increased, respectively, 2.01-fold and 2.34-fold with the recoveries that were in the range of 97.62–102.36% for RU and 97.33–102.21% for QU with RSDs lower than 3.2% under the optimized UMAE conditions. In addition, the shorter extraction time was used in ILs-UMAE, compared with HRE. Therefore, ILs-UMAE was a rapid and an efficient method for the extraction of RU and QU from the leaves of velvetleaf. PMID:25243207

An Isotope Study of Hydrogenation of poly-Si/SiOx Passivated Contacts for Si Solar Cells: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schnabel, Manuel; Nemeth, William; van de Loo, Bas, W.H.

2017-06-26

For many years, the record Si solar cell efficiency stood at 25.0%. Only recently have several companies and institutes managed to produce more efficient cells, using passivated contacts of made doped poly-Si or a-Si:H and a passivating intrinsic interlayer in all cases. Common to these designs is the need to passivate the layer stack with hydrogen. In this contribution, we perform a systematic study of passivated contact passivation by hydrogen, using poly-Si/SiOx passivated contacts on n-Cz-Si, and ALD Al2O3 followed by a forming gas anneal (FGA) as the hydrogen source. We study p-type and n-type passivated contacts with implied Vocmore » exceeding 690 and 720 mV, respectively, and perform either the ALD step or the FGA with deuterium instead of hydrogen in order to separate the two processes via SIMS. By examining the deuterium concentration at the SiOx in both types of samples, we demonstrate that the FGA supplies negligible hydrogen species to the SiOx, regardless of whether the FGA is hydrogenated or deuterated. Instead, it supplies the thermal energy needed for hydrogen species in the Al2O3 to diffuse there. Furthermore, the concentration of hydrogen species at the SiOx can saturate while implied Voc continues to increase, showing that the energy from the FGA is also required for hydrogen species already at the SiOx to find recombination-active defects to passivate.« less

Physical contact between human vascular endothelial and smooth muscle cells modulates cytosolic and nuclear calcium homeostasis.

PubMed

Hassan, Ghada S; Jacques, Danielle; D'Orléans-Juste, Pedro; Magder, Sheldon; Bkaily, Ghassan

2018-05-14

The interaction between vascular endothelial cells (VECs) and vascular smooth muscle cells (VSMCs) plays an important role in the modulation of vascular tone. There is, however, no information on whether direct physical communication regulates the intracellular calcium levels of human VECs (hVECs) and (or) human VSMCs (hVSMCs). Thus, the objective of the study is to verify whether co-culture of hVECs and hVSMCs modulates cytosolic ([Ca 2+ ] c ) and nuclear calcium ([Ca 2+ ] n ) levels via physical contact and (or) factors released by both cell types. Quantitative 3D confocal microscopy for [Ca 2+ ] c and [Ca 2+ ] n measurement was performed in cultured hVECs or hVSMCs or in co-culture of hVECs-hVSMCs. Our results show that: (1) physical contact between hVECs-hVECs or hVSMCs-hVSMCs does not affect [Ca 2+ ] c and [Ca 2+ ] n in these 2 cell types; (2) physical contact between hVECs and hVSMCs induces a significant increase only of [Ca 2+ ] n of hVECs without affecting the level of [Ca 2+ ] c and [Ca 2+ ] n of hVSMCs; and (3) preconditioned culture medium of hVECs or hVSMCs does not affect [Ca 2+ ] c and [Ca 2+ ] n of both types of cells. We concluded that physical contact between hVECs and hVSMCs only modulates [Ca 2+ ] n in hVECs. The increase of [Ca 2+ ] n in hVECs may modulate nuclear functions that are calcium dependent.

Is Contact with Children Related to Legitimizing Beliefs Toward Sex with Children Among Men with Pedophilia?

PubMed

Geradt, Max; Jahnke, Sara; Heinz, Julia; Hoyer, Jürgen

2018-02-01

Among pedophilic men, social contact with children has been discussed as creating a risk situation for sexual abuse. Also, pedophilic men searching for such contact are seen as harboring more beliefs legitimizing sexual contact with children. However, social contact may also decrease false beliefs. We tested these competing views in an anonymous Internet survey with a non-forensic, non-clinical sample of 104 self-classified pedophilic men. Results showed that both increased social and physical contact were significantly linked to fewer legitimizing beliefs toward sex with children, even when controlling for past psychotherapy, educational level, social desirability, and age. Controlling for previous conviction for child sexual offenses reduced the effect for physical contact, but not for social contact. Exploratory analyses showed that either type of contact had no significant effect on total self-perceived risk of offending. However, pedophilic men with physical contact with children perceived a higher risk of more direct (i.e., child abuse) than indirect offenses (i.e., child pornography offenses) compared to pedophilic men without physical contact. Despite limitations of the correlational design and the only small to moderate effects, the results challenge the assumption that complete avoidance of contact with children is necessary for persons with pedophilia to reduce the risk of abusive behavior.

Nature Contacts: Employee Wellness in Healthcare.

PubMed

Trau, Deborah; Keenan, Kimberly A; Goforth, Meggan; Large, Vernon

2016-04-01

This study was designed to ascertain the amount of outdoor, indoor, and indirect nature contact exposures hospital employees have in a workweek. Hospital employees have been found particularly vulnerable to work-related stress. Increasing the nature contact exposure for hospital employees can reduce perceived stress; stress-related health behaviors; and stress-related health outcomes from outdoor, indoor, and indirect exposures to nature. Staff on the fourth floor postsurgical unit of a large hospital (N = 42) were ask to participate in an employee questionnaire "nature contact questionnaire". This 16-item nature environment questionnaire measures the amount and types of nature contact exposures employees have during a workweek. Majority of employees reported few, if any, nature contact exposures, specifically in the area of outdoor nature contacts with limited indoor and indirect contacts. These results indicated that employees on the fourth floor postsurgical floor have limited ability to reduce stress through nature contact exposures which could impact their perceived levels of work stress and stress-related behaviors and health outcomes. Nature contact exposures are both a relatively easy and an inexpensive way to improve employee stress. These findings indicate limitations to employees' exposure to nature contacts. Healthcare environments would benefit from a concerted effort to provide increased outdoor, indoor, and indirect nature contact exposures for employees. © The Author(s) 2015.

Inferring a District-Based Hierarchical Structure of Social Contacts from Census Data

PubMed Central

Yu, Zhiwen; Liu, Jiming; Zhu, Xianjun

2015-01-01

Researchers have recently paid attention to social contact patterns among individuals due to their useful applications in such areas as epidemic evaluation and control, public health decisions, chronic disease research and social network research. Although some studies have estimated social contact patterns from social networks and surveys, few have considered how to infer the hierarchical structure of social contacts directly from census data. In this paper, we focus on inferring an individual’s social contact patterns from detailed census data, and generate various types of social contact patterns such as hierarchical-district-structure-based, cross-district and age-district-based patterns. We evaluate newly generated contact patterns derived from detailed 2011 Hong Kong census data by incorporating them into a model and simulation of the 2009 Hong Kong H1N1 epidemic. We then compare the newly generated social contact patterns with the mixing patterns that are often used in the literature, and draw the following conclusions. First, the generation of social contact patterns based on a hierarchical district structure allows for simulations at different district levels. Second, the newly generated social contact patterns reflect individuals social contacts. Third, the newly generated social contact patterns improve the accuracy of the SEIR-based epidemic model. PMID:25679787

The evolution of in-plane magnetic anisotropy in CoFeB/GaAs(001) films annealed at different temperatures

NASA Astrophysics Data System (ADS)

Tu, Hongqing; Wang, Ji; Wei, Lujun; Yuan, Yuan; Zhang, W.; You, Biao; Du, Jun

2018-05-01

A considerable in-plane uniaxial magnetic anisotropy (UMA) field (Hu ˜ 300 Oe) could be achieved when the amorphous CoFeB film was deposited on the GaAs(001) wafer by magnetron-sputtering after proper etch-annealed procedure. In order to get deep insights into the mechanism of the UMA, the film was annealed at different temperatures and the evolution of the in-plane magnetic anisotropy was investigated carefully. With increasing the annealing temperature (TA), the UMA could be maintained well when TA reached 250°C, but became very weak at 300°C. However, when TA was elevated to 400°C, another UMA (Hu ˜ 130 Oe) was built accompanied with a fourfold magnetic anisotropy with its strength of about 50 Oe. In terms of the magnetic anisotropy evolution along with TA, the anelastic strain, which is thought to be resulted from the interfacial interaction between CoFeB and GaAs, may play a dominant role in producing the enhanced UMA based on the `bond-orientational' anisotropy (BOA) model.

Genital and Extragenital Gonorrhea and Chlamydia in Children and Adolescents Evaluated for Sexual Abuse.

PubMed

Kellogg, Nancy D; Melville, John D; Lukefahr, James L; Nienow, Shalon M; Russell, Edward L

2017-01-09

The aim of this study was to describe the use of a nucleic acid amplification test in detecting genital and extragenital Neisseria gonorrhoeae (NG) and Chlamydia trachomatis (CT) in children and adolescents assessed for sexual abuse/assault. The charts of children aged 0 to 17 years, consecutively evaluated for sexual victimization, in emergency department and outpatient settings were reviewed. Data extracted included age, sex, type of sexual contact, anogenital findings, previous sexual contact, toxicology results, and sites tested for NG and CT. Of the 1319 patients who were tested, 579 were tested at more than 1 site, and 120 had at least 1 infected site. Chlamydia trachomatis was identified in 104 patients, and NG was found in 33. In bivariate analysis, a positive test was associated with female sex, age older than 11 years, previous sexual contact, acute or healed genital injury, drug/alcohol intoxication, and examination within 72 hours of sexual contact. Fifty-one patients had positive anal tests, and 24 had positive oral tests. More than 75% of patients with positive extragenital tests had additional positive tests or anogenital injury. Most with a positive anal (59%) or oral (77%) test did not report that the assailant's genitals came into contact with that site. Positive tests for NG and CT in patients evaluated for sexual victimization may represent infection from sexual contact, contiguous spread of infection, or the presence of infected assailant secretions. Relying on patient reports of symptoms, or types of sexual contact, to determine need for testing may miss NG and CT infections in patients evaluated for sexual victimization.

Assessment of modifications in thickness, curvatures, and volume upon the cornea caused by disposable soft contact lens wear.

PubMed

Del Águila-Carrasco, Antonio J; Domínguez-Vicent, Alberto; Pérez-Vives, Cari; Ferrer-Blasco, Teresa; Montés-Micó, Robert

2015-01-01

To assess the effect of different disposable soft contact lenses on several corneal parameters-thickness, anterior and posterior curvature, and volume-by means of a Scheimpflug imaging-based device (Pentacam HR). Diurnal variations of these parameters were taken into account. Twenty-one young, healthy subjects wore 4 different types of daily disposable soft contact lenses on 4 different days: Dailies AquaComfort Plus, SofLens, Dailies Total1, and Acuvue TruEye. The lenses had different material and water content. Pachymetry and curvature maps and corneal volume values were obtained using the Pentacam HR twice a day: one before putting the lens on and one after an 8-hour period of contact lens wear. Measurements were also taken without any contact lenses being worn. Regarding corneal thickness, the lens with the most similar behavior to the naked eye scenario was the Dailies Total1, causing a thickening of 0.2 ± 0.1% in the central zone and 0.6 ± 0.2% in the periphery. All 4 lenses caused a slight but not significant flattening in the anterior corneal curvature, whereas the posterior corneal curvature only experienced a significant but small steepening with the SofLens. The use of these lenses increased corneal volume slightly. Variations in corneal parameters seem to depend on the type of contact lens used (material, oxygen transmissibility, water content). However, the magnitude of the changes introduced by the use of soft contact lenses over the 8-hour period was small and probably not large enough to influence either visual acuity or comfort.

Contact electrification induced interfacial reactions and direct electrochemical nanoimprint lithography in n-type gallium arsenate wafer† †Electronic supplementary information (ESI) available: Electrochemical measurements of the interfaces, optimization of the contact force and temperature of ECNL, XPS analysis, and more examples of ECNL on n-GaAs. See DOI: 10.1039/c6sc04091h Click here for additional data file.

PubMed Central

Zhang, Jie; Zhang, Lin; Wang, Wei; Han, Lianhuan; Jia, Jing-Chun; Tian, Zhao-Wu; Tian, Zhong-Qun

2017-01-01

Although metal assisted chemical etching (MacEtch) has emerged as a versatile micro-nanofabrication method for semiconductors, the chemical mechanism remains ambiguous in terms of both thermodynamics and kinetics. Here we demonstrate an innovative phenomenon, i.e., the contact electrification between platinum (Pt) and an n-type gallium arsenide (100) wafer (n-GaAs) can induce interfacial redox reactions. Because of their different work functions, when the Pt electrode comes into contact with n-GaAs, electrons will move from n-GaAs to Pt and form a contact electric field at the Pt/n-GaAs junction until their electron Fermi levels (E F) become equal. In the presence of an electrolyte, the potential of the Pt/electrolyte interface will shift due to the contact electricity and induce the spontaneous reduction of MnO4 – anions on the Pt surface. Because the equilibrium of contact electrification is disturbed, electrons will transfer from n-GaAs to Pt through the tunneling effect. Thus, the accumulated positive holes at the n-GaAs/electrolyte interface make n-GaAs dissolve anodically along the Pt/n-GaAs/electrolyte 3-phase interface. Based on this principle, we developed a direct electrochemical nanoimprint lithography method applicable to crystalline semiconductors. PMID:28451347

Ohmic contacts to n-GaN formed by ion-implanted Si into p-GaN

NASA Astrophysics Data System (ADS)

Bao, Xichang; Xu, Jintong; Zhang, Wenjing; Wang, Ling; Chu, Kaihui; Li, Chao; Li, Xiangyang

2009-07-01

In this paper, we report the ohmic contact to n-GaN fabricated by implanting silicon into Mg-doped GaN using an alloy of Ti/Al/Ti/Au metallization. The used materials were grown on (001) sapphire substrates by metal-organic chemical-vapor deposition (MOCVD). The layer structure was comprised of a GaN buffer layer and followed by a 2 μm thickness Mg-doped GaN (Na=5×1017cm-3) and then double silicon implantation was performed in order to convert p-type GaN into n-type GaN films. The as-implanted samples were then thermal annealed at 1150 °C for 5 min in N2 ambient. The carrier concentration and Hall mobility were 3.13×1018 cm3 and 112 cm2/ (VÂ.s) measured by Hall method. Multilayer electrode of Ti (50 nm)/Al (50 nm)/Ti (30 nm)/Au (30 nm) was deposited on n-GaN using an electron-beam evaporation and contacts were formed by a N2 annealing technique ranging from 600 to 900 °C. After annealing lower than 700 °C, the contacts exhibited a rectifying behavior and became ohmic contact only after high temperature processes (>=700 °C). Specific contact resistance was as low as 9.58×10-4 ΩÂ.cm2 after annealing at 800 °C for 60 seconds. While annealing temperature is higher than 800 °C, the specific contact resistance becomes worse. This phenomenon is caused by the surface morphology degradation.

Concentration Levels of Particulate Matter of Common Dental Lab Materials in a Military Dental Lab

DTIC Science & Technology

2016-05-01

to cause contact type dermatitis in some dental laboratory technicans. 22 In both experimental animals and humans, methyl methacrylate is rapidly...being measured out and mixed. As cases of generalized neuropathy, asthma and contact dermatitis have been documented in dental laboratory technicians... contact .45 The sampling for paraffin wax particulate in the current study resulted in a REL 8-TWA of 0.2056 mg/m 3 which is well below the 2 mg/m 3

Improved ion detector

DOEpatents

Tullis, A.M.

1986-01-30

An improved ion detector device of the ionization detection device chamber type comprises an ionization chamber having a central electrode therein surrounded by a cylindrical electrode member within the chamber with a collar frictionally fitted around at least one of the electrodes. The collar has electrical contact means carried in an annular groove in an inner bore of the collar to contact the outer surface of the electrode to provide electrical contact between an external terminal and the electrode without the need to solder leads to the electrode.

Operational Use Of Contact Lenses By Military Aircrew (L’Utilisation Operationnelle des Lentilles de Contact)

DTIC Science & Technology

1992-10-01

Astigmatism 1 I Accommodation and Convergence 12 Advantages and Disadvantages of Contact Lenses 12 Optical Performance 12 Compliance 13 Supervision 13...absence of parallel tear lens, especially advantages of dealing with only one type of lens and accompanying astigmatism ) support system. - discomfort...Polcon I low. provides an explanation for the failure of high Dk Potycon 1I 8 a materials in fitting a cornea with astigmatism and the Si-02-•• ex need

Oxygen-Free Welding Contact Tips

NASA Technical Reports Server (NTRS)

Pike, James F.

1993-01-01

Contact tips for gas/metal arc welding (GMAW) fabricated from oxygen-free copper. Prototype tips tested in robotic welding, for which application intended. Reduces electrical erosion, increases electrical conductivity, and reduces mechanical wear. Productivity of robotic welding increases while time during welding interrupted for removal and replacement of contact tips minimal. Improves alignment of joints and filler metal, reducing rate of rejection and repair of unacceptable weldments. Utility extends beyond aerospace industry to mass production of various types of hardware, including heavy off-highway construction equipment.

Association of contact urticaria and allergic contact dermatitis to rubber.

PubMed

Fernadez, Ohalis Luanda; Canosa, Juliana Macedo; Lazzarini, Rosana; Duarte, Ida

2009-01-01

We present a case of a healthcare professional that developed type I and IV hypersensitivity reactions to rubber. During the clinical examination the patient showed eczematous dermatitis of the hands. The patch test was positive for thiuram group and an open test with a piece of glove was positive after 20 minutes of exposure. Allergen-specific IgE test (RAST) was relevant. Reactions to rubber allergens are frequent among healthcare professionals due to constant contact with this material.

On Ni/Au Alloyed Contacts to Mg-Doped GaN

NASA Astrophysics Data System (ADS)

Sarkar, Biplab; Reddy, Pramod; Klump, Andrew; Kaess, Felix; Rounds, Robert; Kirste, Ronny; Mita, Seiji; Kohn, Erhard; Collazo, Ramon; Sitar, Zlatko

2018-01-01

Ni/Au contacts to p-GaN were studied as a function of free hole concentration in GaN using planar transmission line measurement structures. All contacts showed a nonlinear behavior, which became stronger for lower doping concentrations. Electrical and structural analysis indicated that the current conduction between the contact and the p-GaN was through localized nano-sized clusters. Thus, the non-linear contact behavior can be well explained using the alloyed contact model. Two contributions to the contact resistance were identified: the spreading resistance in the semiconductor developed by the current crowding around the electrically active clusters, and diode-type behavior at the interface of the electrically active clusters with the semiconductor. Hence, the equivalent Ni/Au contact model consists of a diode and a resistor in series for each active cluster. The reduced barrier height observed in the measurements is thought to be generated by the extraction of Ga from the crystalline surface and localized formation of the Au:Ga phase. The alloyed contact analyses presented in this work are in good agreement with some of the commonly observed behavior of similar contacts described in the literature.

Rescore protein-protein docked ensembles with an interface contact statistics.

PubMed

Mezei, Mihaly

2017-02-01

The recently developed statistical measure for the type of residue-residue contact at protein complex interfaces, based on a parameter-free definition of contact, has been used to define a contact score that is correlated with the likelihood of correctness of a proposed complex structure. Comparing the proposed contact scores on the native structure and on a set of model structures the proposed measure was shown to generally favor the native structure but in itself was not able to reliably score the native structure to be the best. Adjusting the scores of redocking experiments with the contact score showed that the adjusted score was able to move up the ranking of the native-like structure among the proposed complexes when the native-like was not ranked the best by the respective program. Tests on docking of unbound proteins compared the contact scores of the complexes with the contact score of the crystal structure again showing the tendency of the contact score to favor native-like conformations. The possibility of using the contact score to improve the determination of biological dimers in a crystal structure was also explored. Proteins 2017; 85:235-241. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

One Thousand New Dwarf Novae from the OGLE Survey

NASA Astrophysics Data System (ADS)

Mróz, P.; Udalski, A.; Poleski, R.; Pietrukowicz, P.; Szymański, M. K.; Soszyński, I.; Wyrzykowski, Ł.; Ulaczyk, K.; Kozłowski, S.; Skowron, J.

2015-12-01

We present one of the largest collections of dwarf novae (DNe) containing 1091 objects that have been discovered in the long-term photometric data from the Optical Gravitational Lensing Experiment (OGLE) survey. They were found in the OGLE fields toward the Galactic bulge and the Magellanic Clouds. We analyze basic photometric properties of all systems and tentatively find a population of DNe from the Galactic bulge. We identify several dozen of WZ Sge-type DN candidates, including two with superhump periods longer than 0.09 d. Other interesting objects include SU UMa-type stars with "early" precursor outbursts or a Z Cam-type star showing outbursts during standstills. We also provide a list of DNe which will be observed during the K2 Campaign 9 microlensing experiment in 2016. Finally, we present the new OGLE-IV real-time data analysis system: CVOM, which has been designed to provide continuous real time photometric monitoring of selected CVs.

Asymmetrically interacting spreading dynamics on complex layered networks.

PubMed

Wang, Wei; Tang, Ming; Yang, Hui; Younghae Do; Lai, Ying-Cheng; Lee, GyuWon

2014-05-29

The spread of disease through a physical-contact network and the spread of information about the disease on a communication network are two intimately related dynamical processes. We investigate the asymmetrical interplay between the two types of spreading dynamics, each occurring on its own layer, by focusing on the two fundamental quantities underlying any spreading process: epidemic threshold and the final infection ratio. We find that an epidemic outbreak on the contact layer can induce an outbreak on the communication layer, and information spreading can effectively raise the epidemic threshold. When structural correlation exists between the two layers, the information threshold remains unchanged but the epidemic threshold can be enhanced, making the contact layer more resilient to epidemic outbreak. We develop a physical theory to understand the intricate interplay between the two types of spreading dynamics.

Asymmetrically interacting spreading dynamics on complex layered networks

PubMed Central

Wang, Wei; Tang, Ming; Yang, Hui; Younghae Do; Lai, Ying-Cheng; Lee, GyuWon

2014-01-01

The spread of disease through a physical-contact network and the spread of information about the disease on a communication network are two intimately related dynamical processes. We investigate the asymmetrical interplay between the two types of spreading dynamics, each occurring on its own layer, by focusing on the two fundamental quantities underlying any spreading process: epidemic threshold and the final infection ratio. We find that an epidemic outbreak on the contact layer can induce an outbreak on the communication layer, and information spreading can effectively raise the epidemic threshold. When structural correlation exists between the two layers, the information threshold remains unchanged but the epidemic threshold can be enhanced, making the contact layer more resilient to epidemic outbreak. We develop a physical theory to understand the intricate interplay between the two types of spreading dynamics. PMID:24872257

Contact integrity testing of stress-tested silicon terrestrial solar cells

NASA Technical Reports Server (NTRS)

Prince, J. L.; Lathrop, J. W.; Witter, G. W.

1980-01-01

A test procedure was developed and applied to terrestrial silicon solar cells in order to determine the effect of accelerated environmental and time-temperature aging on metal contact integrity. Quantities of cells of four different manufacturers were given the contact integrity test after being subjected to accelerated stress tests that included forward bias-temperature, thermal cycle and thermal shock, power cycle, and bias-temperature humidity tests at two temperature-humidity levels. Significant effects due to certain stress tests were found for some cell types. It is concluded that cells fabricated using plated nickel/solder metallization showed significantly more serious contact integrity degradation than silver-metallized cells.

Evaluation of Contact Heat Transfer Coefficient and Phase Transformation during Hot Stamping of a Hat-Type Part

PubMed Central

Kim, Heung-Kyu; Lee, Seong Hyeon; Choi, Hyunjoo

2015-01-01

Using an inverse analysis technique, the heat transfer coefficient on the die-workpiece contact surface of a hot stamping process was evaluated as a power law function of contact pressure. This evaluation was to determine whether the heat transfer coefficient on the contact surface could be used for finite element analysis of the entire hot stamping process. By comparing results of the finite element analysis and experimental measurements of the phase transformation, an evaluation was performed to determine whether the obtained heat transfer coefficient function could provide reasonable finite element prediction for workpiece properties affected by the hot stamping process. PMID:28788046

Break-junction experiments on the zero-bias anomaly of non-magnetic and ferromagnetically ordered metals

NASA Astrophysics Data System (ADS)

Gloos, Kurt; Tuuli, Elina

2012-12-01

We have investigated break junctions of normal non-magnetic metals as well as ferromagnets at low temperatures. The point contacts with radii 0.15—15 nm showed zero-bias anomalies which can be attributed to Kondo scattering at a single Kondo impurity at the contact or to the switching of a single conducting channel. The Kondo temperatures derived from the width of the anomalies varied between 10 and 1000 K. These results agree well with literature data on atomic-size contacts of the ferromagnets as well as with spear-anvil type contacts on a wide variety of metals.

Modeling environmental contamination in hospital single- and four-bed rooms.

PubMed

King, M-F; Noakes, C J; Sleigh, P A

2015-12-01

Aerial dispersion of pathogens is recognized as a potential transmission route for hospital acquired infections; however, little is known about the link between healthcare worker (HCW) contacts' with contaminated surfaces, the transmission of infections and hospital room design. We combine computational fluid dynamics (CFD) simulations of bioaerosol deposition with a validated probabilistic HCW-surface contact model to estimate the relative quantity of pathogens accrued on hands during six types of care procedures in two room types. Results demonstrate that care type is most influential (P < 0.001), followed by the number of surface contacts (P < 0.001) and the distribution of surface pathogens (P = 0.05). Highest hand contamination was predicted during Personal care despite the highest levels of hand hygiene. Ventilation rates of 6 ac/h vs. 4 ac/h showed only minor reductions in predicted hand colonization. Pathogens accrued on hands decreased monotonically after patient care in single rooms due to the physical barrier of bioaerosol transmission between rooms and subsequent hand sanitation. Conversely, contamination was predicted to increase during contact with patients in four-bed rooms due to spatial spread of pathogens. Location of the infectious patient with respect to ventilation played a key role in determining pathogen loadings (P = 0.05). We present the first quantitative model predicting the surface contacts by HCW and the subsequent accretion of pathogenic material as they perform standard patient care. This model indicates that single rooms may significantly reduce the risk of cross-contamination due to indirect infection transmission. Not all care types pose the same risks to patients, and housekeeping performed by HCWs may be an important contribution in the transmission of pathogens between patients. Ventilation rates and positioning of infectious patients within four-bed rooms can mitigate the accretion of pathogens, whereby reducing the risk of missed hand hygiene opportunities. The model provides a tool to quantitatively evaluate the influence of hospital room design on infection risk. © 2015 The Authors. Indoor Air Published by John Wiley & Sons Ltd.

Impact of Cosmetics on the Surface Properties of Silicone Hydrogel Contact Lenses.

PubMed

Srinivasan, Sruthi; Otchere, Heinz; Yu, Mili; Yang, Jeffery; Luensmann, Doerte; Jones, Lyndon

2015-07-01

This study evaluated the impact of various cosmetics on the surface properties of silicone hydrogel (SiHy) contact lens materials. In this in vitro experiment, 7 SiHy contact lens materials were coated with 1 of 9 cosmetics, including common hand creams (3), eye makeup removers (3), and mascaras (3). Dark-field microscopy images were taken to determine pixel brightness (PB) after cosmetic exposure, which describes the visible surface deposition (n=6 for each lens type), with a higher PB indicating increased deposition. The sessile drop technique was used to determine the advancing contact angle (CA). Measurements were repeated for both methods after a single peroxide-based cleaning cycle. Pixel brightness was significantly higher for mascara-coated lenses compared with the other cosmetic products (P<0.01). The peroxide-based lens care solution removed most deposits from the nonwaterproof mascara for 4 lens types, whereas deposits remained relatively unchanged for 1 waterproof mascara (P>0.05). Hand creams and makeup remover had minimal impact on PB. Changes in CA measurements after cosmetic application were highly lens dependent. Hand creams caused primarily a decrease in CA for 5 of the 7 lens types, whereas 1 of the waterproof mascaras caused a significant increase of 30 to 50° for 3 lens types. Some mascara-lens combinations resulted in increased CA and PB, which could have an impact on in vivo lens performance. Nonwaterproof mascara was mostly removed after a cleaning cycle. Further research is needed to understand the clinical implications for SiHy lens wearers using cosmetics.

Schottky barrier detection devices having a 4H-SiC n-type epitaxial layer

DOEpatents

Mandal, Krishna C.; Terry, J. Russell

2016-12-06

A detection device, along with methods of its manufacture and use, is provided. The detection device can include: a SiC substrate defining a substrate surface cut from planar to about 12.degree.; a buffer epitaxial layer on the substrate surface; a n-type epitaxial layer on the buffer epitaxial layer; and a top contact on the n-type epitaxial layer. The buffer epitaxial layer can include a n-type 4H--SiC epitaxial layer doped at a concentration of about 1.times.10.sup.15 cm.sup.-3 to about 5.times.10.sup.18 cm.sup.-3 with nitrogen, boron, aluminum, or a mixture thereof. The n-type epitaxial layer can include a n-type 4H--SiC epitaxial layer doped at a concentration of about 1.times.10.sup.13 cm.sup.-3 to about 5.times.10.sup.15 cm.sup.-3 with nitrogen. The top contact can have a thickness of about 8 nm to about 15 nm.

Biomechanical consequences of a posterior root tear of the lateral meniscus: stabilizing effect of the meniscofemoral ligament.

PubMed

Forkel, Philipp; Herbort, Mirco; Schulze, Martin; Rosenbaum, Dieter; Kirstein, Lars; Raschke, Michael; Petersen, Wolf

2013-05-01

The purpose of this study was to evaluate the effects of different types of lateral meniscus root tears in terms of tibiofemoral contact stress. Ten porcine knees each underwent five different testing conditions with the menisci intact, a simulated lateral posterior root tear with and without cutting the meniscofemoral ligament and with an artificial tear of the posterior root of the medial meniscus. Biomechanical testing was performed at 30° of flexion with an axial load of 100 N. A pressure sensor (st Sensor Type S2042, Novel, Munich) was used to measure the tibiofemoral contact area and the tibiofemoral contact pressure. Data were analyzed to assess the differences in contact area and tibiofemoral peak contact pressure among the five meniscal conditions. There was no significant difference in mean contact pressure between the state with the menisci intact and an isolated posterior root tear of the lateral meniscus. In case of a root tear and a tear of the meniscofemoral ligament, the contact area decreased in comparison with the intact state of the menisci. After additional cutting of the meniscofemoral ligament, the tibiofemoral contact pressure was significantly higher in comparison with the intact state and the avulsion injury. In the medial compartment, joint compression forces were significantly increased in comparison with the intact state after cutting the posterior root of the medial meniscus (P < 0.05). The consequence of a medial meniscus root tear is well known and was verified by this analysis. The results of the present study show that the biomechanical consequences of a lateral meniscus root tear depend on the state of the meniscofemoral ligament. An increase in tibiofemoral contact pressure is only to be expected in combined injuries of the meniscus root and the meniscofemoral ligaments. Posterior lateral meniscus root tear might have a better prognosis in terms of the development of osteoarthritis when the meniscofemoral ligament is intact.

Influence of axial self-magnetic field component on arcing behavior of spiral-shaped contacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Dingyu; Xiu, Shixin, E-mail: xsx@mail.xjtu.edu.cn; Wang, Yi

2015-10-15

The transverse magnetic field (TMF) contact design is commonly used in vacuum interrupters. When arcing occurs between the TMF contacts, the contact structure can create a self-induced magnetic field that drives the arc to move and rotate on the contact, and thus local overheating and severe erosion can be avoided. However, TMF contacts could also create an axial self-magnetic component, and the influence of this component on the arc behavior has not been considered to date. In this paper, five different types of Cu-Cr spiral-shaped TMF contacts with three different structures are investigated in a demountable vacuum chamber that containsmore » a high-speed charge-coupled device video camera. It was found that the contact structure greatly influenced the arc behavior, especially in terms of arc rotation and the effective contact area, while contacts with the same slot structure but different diameters showed similar arc behavior and arc motion. The magnetic field distribution and the Lorentz force of each of the three different contact structures are simulated, and the axial self-magnetic field was first taken into consideration for investigation of the TMF contact design. It was found that contact designs that have higher axial self-magnetic field components tend to have arc columns with larger diameters and show poorer arc motion and rotation performance in the experiments.« less

A Thermally Stable NiZn/Ta/Ni Scheme to Replace AuBe/Au Contacts in High-Efficiency AlGaInP-Based Light-Emitting Diodes

NASA Astrophysics Data System (ADS)

Kim, Dae-Hyun; Park, Jae-Seong; Kang, Daesung; Seong, Tae-Yeon

2017-08-01

We developed NiZn/(Ta/)Ni ohmic contacts to replace expensive AuBe/Au contacts commonly used in high-efficiency AlGaInP-based light-emitting diodes (LEDs), and compared the electrical properties of the two contact types. Unlike the AuBe/Au (130 nm/100 nm) contact, the NiZn/Ta/Ni (130 nm/20 nm/100 nm) contact shows improved electrical properties after being annealed at 500°C, with a contact resistivity of 5.2 × 10-6 Ω cm2. LEDs with the NiZn/Ta/Ni contact exhibited a 4.4% higher output power (at 250 mW) than LEDs with the AuBe/Au contact. In contrast to the trend for the AuBe/Au contact, the Ga 2 p core level for the NiZn/Ta/Ni contact shifted toward lower binding energies after being annealed at 500°C. Auger electron spectroscopy (AES) depth profiles showed that annealing the AuBe/Au samples caused the outdiffusion of both Be and P atoms into the metal contact, whereas in the NiZn/Ta/Ni samples, Zn atoms indiffused into the GaP layer. The annealing-induced electrical degradation and ohmic contact formation mechanisms are described and discussed on the basis of the results of x-ray photoemission spectroscopy and AES.

The Quantified Characterization Method of the Micro-Macro Contacts of Three-Dimensional Granular Materials on the Basis of Graph Theory.

PubMed

Guan, Yanpeng; Wang, Enzhi; Liu, Xiaoli; Wang, Sijing; Luan, Hebing

2017-08-03

We have attempted a multiscale and quantified characterization method of the contact in three-dimensional granular material made of spherical particles, particularly in cemented granular material. Particle contact is defined as a type of surface contact with voids in its surroundings, rather than a point contact. Macro contact is a particle contact set satisfying the restrictive condition of a two-dimensional manifold with a boundary. On the basis of graph theory, two dual geometrical systems are abstracted from the granular pack. The face and the face set, which satisfies the two-dimensional manifold with a boundary in the solid cell system, are extracted to characterize the particle contact and the macro contact, respectively. This characterization method is utilized to improve the post-processing in DEM (Discrete Element Method) from a micro perspective to describe the macro effect of the cemented granular material made of spherical particles. Since the crack has the same shape as its corresponding contact, this method is adopted to characterize the crack and realize its visualization. The integral failure route of the sample can be determined by a graph theory algorithm. The contact force is assigned to the weight value of the face characterizing the particle contact. Since the force vectors can be added, the macro contact force can be solved by adding the weight of its corresponding faces.

78 FR 12058 - Information Collection Being Reviewed by the Federal Communications Commission Under Delegated...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-21

... to [email protected] and Cathy.Williams@fcc.gov . FOR FURTHER INFORMATION CONTACT: For additional information about the information collection, contact Cathy Williams at (202) 418-2918. SUPPLEMENTARY INFORMATION: OMB Number: 3060-0180. Title: Section 73.1610, Equipment Tests. Form Number: N/A. Type of Review...

English as a Minority Language in Quebec

ERIC Educational Resources Information Center

Boberg, Charles

2012-01-01

The variety of English spoken by about half a million people in the Canadian province of Quebec is a minority language in intensive contact with French, the local majority language. This unusual contact situation has produced a unique variety of English which displays many instances of French influence that distinguish it from other types of…

Mechanical properties of cellulose nanomaterials studied by contact resonance atomic force microscopy

Treesearch

Ryan Wagner; Robert J. Moon; Arvind Raman

2016-01-01

Quantification of the mechanical properties of cellulose nanomaterials is key to the development of new cellulose nanomaterial based products. Using contact resonance atomic force microscopy we measured and mapped the transverse elastic modulus of three types of cellulosic nanoparticles: tunicate cellulose nanocrystals, wood cellulose nanocrystals, and wood cellulose...

Vincenzo LaSalvia | NREL

Science.gov Websites

;Utilization of Tabula Rasa to stabilize bulk lifetimes in n-Cz silicon for high-performance solar cell /SiOx/pc-Si passivated contacts to n-type Si solar cells." Presented at the 40th IEEE Photovoltaic , and P. Stradins. "Heterojunction rear passivated contact for high efficiency n-Cz Si solar cells

Concentrating Solar Power Projects - Extresol-2 | Concentrating Solar Power

Science.gov Websites

Sesmero (Badajoz) Owner(s): ACS/Cobra Group (100%) Technology: Parabolic trough Turbine Capacity: Net : 158,000 MWh/yr (Expected/Planned) Contact(s): Manuel Cortes; Ana Salazar Company: ACS/Cobra Group Break Project Type: Commercial Participants Developer(s): ACS/Cobra Group Owner(s) (%): ACS/Cobra Group (100

Concentrating Solar Power Projects - Extresol-3 | Concentrating Solar Power

Science.gov Websites

Sesmero (Badajoz) Owner(s): ACS/Cobra Group (100%) Technology: Parabolic trough Turbine Capacity: Net : 158,000 MWh/yr (Expected/Planned) Contact(s): Manuel Cortes; Ana Salazar Company: ACS/Cobra Group Break years Project Type: Commercial Participants Developer(s): ACS/Cobra Group Owner(s) (%): ACS/Cobra Group

Deconstructing Pediatric Depression Trials: An Analysis of the Effects of Expectancy and Therapeutic Contact

ERIC Educational Resources Information Center

Rutherford, Bret R.; Sneed, Joel R.; Tandler, Jane M.; Rindskopf, David; Peterson, Bradley S.; Roose, Steven P.

2011-01-01

Objective: This study investigated how study type, mean patient age, and amount of contact with research staff affected response rates to medication and placebo in acute antidepressant trials for pediatric depression. Method: Data were extracted from nine open, four active comparator, and 18 placebo-controlled studies of antidepressants for…

Influence of typical faults over the dynamic behavior of pantograph-catenary contact force in electric rail transport

NASA Astrophysics Data System (ADS)

Rusu-Anghel, S.; Ene, A.

2017-05-01

The quality of electric energy capture and also the equipment operational safety depend essentially of the technical state of the contact line (CL). The present method for determining the technical state of CL based on advance programming is no longer efficient, due to the faults which can occur into the not programmed areas. Therefore, they cannot be remediated. It is expected another management method for the repairing and maintenance of CL based on its real state which must be very well known. In this paper a new method for determining the faults in CL is described. It is based on the analysis of the variation of pantograph-CL contact force in dynamical regime. Using mathematical modelling and also experimental tests, it was established that each type of fault is able to generate ‘signatures’ into the contact force diagram. The identification of these signatures can be accomplished by an informatics system which will provide the fault location, its type and also in the future, the probable evolution of the CL technical state. The measuring of the contact force is realized in optical manner using a railway inspection trolley which has appropriate equipment. The analysis of the desired parameters can be accomplished in real time by a data acquisition system, based on dedicated software.

Nanoscale electrical characteristics of metal (Au, Pd)-graphene-metal (Cu) contacts

NASA Astrophysics Data System (ADS)

Ruffino, F.; Meli, G.; Grimaldi, M. G.

2016-01-01

Free-standing graphene presents exceptional physical properties (as a high carrier mobility) making it the ideal candidate for the next generation nanoelectronics. However, when graphene layers are inserted in real electronics devices, metal contacting is required. The metal-graphene interaction significantly affects the graphene electrical properties, drastically changing its behavior with respect to the free-standing configuration. So, this work presents an experimental study on the nanoscale electric characteristics of metal/graphene/metal contacts. In particular, starting from single-layer graphene grown on Cu foil we deposited on the graphene surface two different metal films (Au or Pd) and the Au/graphene/Cu and Pd/graphene/Cu current-voltage characteristics are acquired, on the nanometric scale, by the conductive atomic force microscopy. Both systems presented a current voltage rectifying behavior. However, the Au/graphene/Cu system conducts significantly at negative applied bias (graphene behaves as a p-type semiconductor in a meta/semiconductor contact), while in the Pd/graphene/Cu at positive applied bias (graphene behaves as a n-type semiconductor in a metal/semiconductor contact). This difference is discussed on the basis of the band energy diagram at the metal/graphene interface and the modification of the graphene Fermi level due to the Au/graphene or Pd/graphene interaction.

Platelet lysate and chondroitin sulfate loaded contact lenses to heal corneal lesions.

PubMed

Sandri, Giuseppina; Bonferoni, Maria Cristina; Rossi, Silvia; Delfino, Alessio; Riva, Federica; Icaro Cornaglia, Antonia; Marrubini, Giorgio; Musitelli, Giorgio; Del Fante, Claudia; Perotti, Cesare; Caramella, Carla; Ferrari, Franca

2016-07-25

Hemoderivative tear substitutes contain various ephiteliotrophic factors, such as growth factors (GF), involved in ocular surface homeostasis without immunogenic properties. The aim of the present work was the loading of platelet lysate into contact lenses to improve the precorneal permanence of platelet lysate growth factors on the ocular surface to enhance the treatment of corneal lesions. To this purpose, chondroitin sulfate, a sulfated glycosaminoglycan, which is normally present in the extracellular matrix, was associated with platelet lysate. In fact, chondroitin sulfate is capable of electrostatic interaction with positively charged growth factors, in particular, with bFGF, IGF, VEGF, PDGF and TGF-β, resulting in their stabilization and reduced degradation in solution. In the present work, various types of commercially available contact lenses have been loaded with chondroitin sulfate or chondroitin sulfate in association with platelet lysate to achieve a release of growth factors directly onto the corneal surface lesions. One type of contact lenses (PureVision(®)) showed in vitro good proliferation properties towards corneal cells and were able to enhance cut closure in cornea constructs. Copyright © 2016 Elsevier B.V. All rights reserved.

Differentiation of Wines Treated with Wood Chips Based on Their Phenolic Content, Volatile Composition, and Sensory Parameters.

PubMed

Kyraleou, Maria; Kallithraka, Stamatina; Chira, Kleopatra; Tzanakouli, Eleni; Ligas, Ioannis; Kotseridis, Yorgos

2015-12-01

The effects of both wood chips addition and contact time on phenolic content, volatile composition, color parameters, and organoleptic character of red wine made by a native Greek variety (Agiorgitiko) were evaluated. For this purpose, chips from American, French, Slavonia oak, and Acacia were added in the wine after fermentation. A mixture consisting of 50% French and 50% Americal oak chips was also evaluated. In an attempt to categorize wine samples, various chemical parameters of wines and sensory parameters were studied after 1, 2, and 3 mo of contact time with chips. The results showed that regardless of the type of wood chips added in the wines, it was possible to differentiate the samples according to the contact time based on their phenolic composition and color parameters. In addition, wood-extracted volatile compounds seem to be the critical parameter that could separate the samples according to the wood type. The wines that were in contact with Acacia and Slavonia chips could be separated from the rest mainly due to their distinct sensory characters. © 2015 Institute of Food Technologists®

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, L.; Qian, S.-B.; Liao, W.-P.

This paper analyzes the first obtained four-color light curves of V396 Mon using the 2003 version of the W-D code. It is confirmed that V396 Mon is a shallow W-type contact binary system with a mass ratio q = 2.554({+-}0.004) and a degree of contact factor f = 18.9%({+-}1.2%). A period investigation based on all available data shows that the period of the system includes a long-term decrease (dP/dt = -8.57 x 10{sup -8} days yr{sup -1}) and an oscillation (A{sub 3} = 0.0160 day, T{sub 3} = 42.4 yr). They are caused by angular momentum loss and light-time effect,more » respectively. The suspect third body is possibly a small M-type star (about 0.31 solar mass). Though some observations indicate that this system has strong magnetic activity, by our analysis we found that the Applegate mechanism cannot explain the periodic changes. This binary is an especially important system according to Qian's statistics of contact binaries as its mass ratio lies near the proposed pivot point about which the physical structure of contact binaries supposedly oscillates.« less

Current Quality-of-Life Tools Available for Use in Contact Dermatitis.

PubMed

Swietlik, Jacquelyn; Reeder, Margo

2016-01-01

Contact dermatitis is a common dermatologic condition that can cause significant impairment in patients' overall quality of life (QoL). This impact is separate and potentially more clinically relevant than one's disease "severity" in contact dermatitis and should be consistently addressed by dermatologists. Despite this, QoL tools specific to contact dermatitis are lacking, and there is little consistency in the literature regarding the tool used to evaluate clinical response to therapies. Measurements currently available to evaluate disease-related QoL in contact dermatitis fit into 1 of the following 3 general types: generic health-related QoL measures, dermatology-related QoL measures, or specific dermatologic disease-related QoL measures. This article reviews the strengths and weaknesses of existing QoL tools used in contact dermatitis including: Short Form Survey 36, Dermatology Life Quality Index, Skindex-29, Skindex-16, Dermatology-Specific Quality of Life, and Fragrance Quality of Life Index.

Age, gender, social contacts, and psychological distress: findings from the 45 and up study.

PubMed

Phongsavan, Philayrath; Grunseit, Anne C; Bauman, Adrian; Broom, Dorothy; Byles, Julie; Clarke, Judith; Redman, Sally; Nutbeam, Don

2013-09-01

The study examined the relationships between social contact types and psychological distress among mid-older adults. Self-completed data from 236,490 Australian adults aged 45+ years. There was a consistent relationship between increased frequency in phone contacts, social visits, and social group contacts and reduced risk of psychological distress adjusted for demographic and health factors. However, stratified analyses by age showed, with one exception, that no significant associations were found between social group contact frequency and risk of psychological distress for those aged 85 years and older. Furthermore, significant interaction terms revealed that women experience a steeper reduction in risk than men at age 65 to 74 years and 75 to 84 years compared with those aged 45 to 64 years. Social contacts have age and gender differential effects on psychological distress of mid-older Australian adults. Interventions addressing social interaction need to be sensitive to gender and age differences.

Small nanoparticles, surface geometry and contact forces.

PubMed

Takato, Yoichi; Benson, Michael E; Sen, Surajit

2018-03-01

In this molecular dynamics study, we examine the local surface geometric effects of the normal impact force between two approximately spherical nanoparticles that collide in a vacuum. Three types of surface geometries-(i) crystal facets, (ii) sharp edges, and (iii) amorphous surfaces of small nanoparticles with radii R <10 nm-are considered. The impact forces are compared with their macroscopic counterparts described by nonlinear contact forces based on Hertz contact mechanics. In our simulations, edge and amorphous surface contacts with weak surface energy reveal that the average impact forces are in excellent agreement with the Hertz contact force. On the other hand, facet collisions show a linearly increasing force with increasing compression. Our results suggest that the nearly spherical nanoparticles are likely to enable some nonlinear dynamic phenomena, such as breathers and solitary waves observed in granular materials, both originating from the nonlinear contact force.

Fabricating Ohmic contact on Nb-doped SrTiO{sub 3} surface in nanoscale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yuhang; National Key Laboratory of Shock Wave and Detonation Physics, Institute of Fluid Physics, Chinese Academy of Engineering Physics, Mianyang, Sichuan 621999; Shi, Xiaolan

2016-05-09

Fabricating reliable nano-Ohmic contact on wide gap semiconductors is an important yet difficult step in oxide nanoelectronics. We fabricated Ohmic contact on the n-type wide gap oxide Nb-doped SrTiO{sub 3} in nanoscale by mechanically scratching the surface using an atomic force microscopy tip. Although contacted to high work function metal, the scratched area exhibits nearly linear IV behavior with low contact resistance, which maintains for hours in vacuum. In contrast, the unscratched area shows Fowler–Nordheim tunneling dominated Schottky rectifying behavior with high contact resistance. It was found that the Ohmic conductivity in the scratched area was drastically suppressed by oxygenmore » gas indicating the oxygen vacancy origin of the Ohmic behavior. The surface oxygen vacancy induced barrier width reduction was proposed to explain the phenomena. The nanoscale approach is also applicable to macroscopic devices and has potential application in all-oxide devices.« less

Influence of tyre-road contact model on vehicle vibration response

NASA Astrophysics Data System (ADS)

Múčka, Peter; Gagnon, Louis

2015-09-01

The influence of the tyre-road contact model on the simulated vertical vibration response was analysed. Three contact models were compared: tyre-road point contact model, moving averaged profile and tyre-enveloping model. In total, 1600 real asphalt concrete and Portland cement concrete longitudinal road profiles were processed. The linear planar model of automobile with 12 degrees of freedom (DOF) was used. Five vibration responses as the measures of ride comfort, ride safety and dynamic load of cargo were investigated. The results were calculated as a function of vibration response, vehicle velocity, road quality and road surface type. The marked differences in the dynamic tyre forces and the negligible differences in the ride comfort quantities were observed among the tyre-road contact models. The seat acceleration response for three contact models and 331 DOF multibody model of the truck semi-trailer was compared with the measured response for a known profile of test section.

Comparison of self-reported and observed water contact in an S. mansoni endemic village in Brazil.

PubMed

Friedman, J F; Kurtis, J D; McGarvey, S T; Fraga, A L; Silveira, A; Pizziolo, V; Gazzinelli, G; LoVerde, P; Corrêa-Oliveira, R

2001-03-30

Estimates of exposure are critical for immuno-epidemiologic and intervention studies in human schistosomiasis. Direct observation of human water contact patterns is both costly and time consuming. To address these issues, we determined whether individuals residing in a Schistosoma mansoni endemic village in Brazil could accurately self-report their water contact patterns. We compared the results of a water contact questionnaire to the present gold standard, direct observation of water contact in 86 volunteers, aged 8--29. We administered a survey to estimate volunteers' frequency and type of water contact and directly measured each volunteers' water contact patterns during 5 weeks of detailed water contact observations. We found a poor correlation between self reported frequency of contact and directly observed exposure (rho=0.119, P=NS). The questionnaire data was supplemented by information about average body surface area of exposure and duration of contact for specific activities derived from observations of this cohort. This 'supplemented questionnaire' data was significantly correlated with their exposure index (rho=0.227, P=0.05). It provides a starting point from which questionnaires may develop to provide a more cost-effective and less labor intensive method of assessing water contact exposure at the level of the individual.

Stabilization of Wide Band-Gap p-Type Wurtzite MnTe Thin Films on Amorphous Substrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zakutayev, Andriy A; Siol, Sebastian; Han, Yanbing

An important challenge in the development of optoelectronic devices for energy conversion applications is the search for suitable p-type contact materials. For example, p-type MnTe would be a promising alternative back contact to due to their chemical compatibility, but at normal conditions it has too narrow band gap due to octahedrally coordinated nickeline (NC) structure. The tetrahedrally coordinated wurtzite (WZ) polymorph of MnTe has not been reported, but it is especially interesting due to its predicted wider band gap, and because of better structural compatibility with CdTe and related II-VI semiconductor materials. Here, we report on the stabilization of WZ-MnTemore » thin films on amorphous indium zinc oxide (a-IZO) substrates relevant to photovoltaic applications. Optical spectroscopy of the WZ-MnTe films shows a wide direct band gap of Eg = 2.7 eV, while PES measurements reveal weak p-type doping with the Fermi level 0.6 eV above the valence band maximum. The results of electron microscopy and photoelectron spectroscopy (PES) measurements indicate that the WZ-MnTe is stabilized due to interdiffusion at the interface with IZO. The results of this work introduce a substrate stabilized WZ-MnTe polymorph as a potential p-type contact material candidate for future applications in CdTe devices for solar energy conversion and other optoelectronic technologies.« less

Analysis of the surface effects on adhesion in MEMS structures

NASA Astrophysics Data System (ADS)

Rusu, F.; Pustan, M.; Bîrleanu, C.; Müller, R.; Voicu, R.; Baracu, A.

2015-12-01

One of the main failure causes in microelectromechanical systems (MEMS) is stiction. Stiction is the adhesion of contacting surfaces due to surface forces. Adhesion force depends on the operating conditions and is influenced by the contact area. In this study, the adhesion force between MEMS materials and the AFM tips is analyzed using the spectroscopy in point mode of the AFM. The aim is to predict the stiction failure mode in MEMS. The investigated MEMS materials are silicon, polysilicon, platinum, aluminum, and gold. Three types of investigations were conducted. The first one aimed to determine the variation of the adhesion force with respect to the variation of the roughness. The roughness has a strong influence on the adhesion because the contact area between components increases if the roughness decreases. The second type of investigation aimed to determine the adhesion force in multiple points of each considered sample. The values obtained experimentally for the adhesion force were also validated using the JKR and DMT models. The third type of investigation was conducted with the purpose of determining the influence of the temperature on the adhesion force.

WZ Cygni: A Marginal Contact Binary in a Triple System?

NASA Astrophysics Data System (ADS)

Lee, Jae Woo; Kim, Seung-Lee; Lee, Chung-Uk; Kim, Ho-Il; Park, Jang-Ho; Hinse, Tobias Cornelius

2011-07-01

We present new multiband CCD photometry for WZ Cyg made on 22 nights in two observing seasons of 2007 and 2008. Our light-curve synthesis indicates that the system is in poor thermal contact with a fill-out factor of 4.8% and a temperature difference of 1447 K. Including our 40 timing measurements, a total of 371 times of minimum light spanning more than 112 yr were used for a period study. Detailed analysis of the O-C diagram showed that the orbital period has varied by a combination of an upward parabola and a sinusoid. The upward parabola means continuous period increase and indicates that some stellar masses are thermally transferred to the more massive primary star at a rate of about 5.80 × 10-8 M sun yr-1. The sinusoidal variation with a period of 47.9 yr and a semi-amplitude of 0.008 days can most likely be interpreted as the light-travel-time effect due to the existence of a low-mass M-type tertiary companion with a projected mass of M 3sin i 3 = 0.26 M sun. We examined the evolutionary status of WZ Cyg from the absolute dimensions of the eclipsing pair. It belongs to the marginal contact binary systems before the broken contact phase, consisting of a massive primary star with spectral type F4 and a secondary star with type K1.

The helical domain of the EcoR124I motor subunit participates in ATPase activity and dsDNA translocation

PubMed Central

Shamayeva, Katsiaryna; Guzanova, Alena; Řeha, David; Csefalvay, Eva; Carey, Jannette; Weiserova, Marie

2017-01-01

Type I restriction-modification enzymes are multisubunit, multifunctional molecular machines that recognize specific DNA target sequences, and their multisubunit organization underlies their multifunctionality. EcoR124I is the archetype of Type I restriction-modification family IC and is composed of three subunit types: HsdS, HsdM, and HsdR. DNA cleavage and ATP-dependent DNA translocation activities are housed in the distinct domains of the endonuclease/motor subunit HsdR. Because the multiple functions are integrated in this large subunit of 1,038 residues, a large number of interdomain contacts might be expected. The crystal structure of EcoR124I HsdR reveals a surprisingly sparse number of contacts between helicase domain 2 and the C-terminal helical domain that is thought to be involved in assembly with HsdM. Only two potential hydrogen-bonding contacts are found in a very small contact region. In the present work, the relevance of these two potential hydrogen-bonding interactions for the multiple activities of EcoR124I is evaluated by analysing mutant enzymes using in vivo and in vitro experiments. Molecular dynamics simulations are employed to provide structural interpretation of the functional data. The results indicate that the helical C-terminal domain is involved in the DNA translocation, cleavage, and ATPase activities of HsdR, and a role in controlling those activities is suggested. PMID:28133570

PALS, MIR and UV-vis-NIR spectroscopy studies of pHEMA hydrogel, silicon- and fluoro-containing contact lens materials

NASA Astrophysics Data System (ADS)

Filipecka, Katarzyna; Budaj, Mariusz; Chamerski, Kordian; Miedziński, Rafał; Sitarz, Maciej; Miskowiak, Bogdan; Makowska-Janusik, Małgorzata; Filipecki, Jacek

2017-11-01

Studies on polymeric materials used in contactology for manufacturing of contact lenses are presented in the paper. Different types of brand new contact lenses were investigated: hydrogel, silicone-hydrogel and rigid gas permeable. Positron annihilation lifetime spectroscopy (PALS) was used to characterize geometrical sizes and fraction of the free volume holes in the investigated samples. Measurements reveal significant differences between the materials. Namely differences in size and fraction of free volume were observed. These changes are strongly correlated with oxygen permeability in contact lenses. Middle infrared (MIR) spectroscopy was carried out in order to investigate the internal structure of materials. Furthermore, UV-vis-NIR studies were performed in order to determine the transmittance properties of contact lenses.

[Sport injuries in full contact and semi-contact karate].

PubMed

Greier, K; Riechelmann, H; Ziemska, J

2014-03-01

Karate enjoys great popularity both in professional and recreational sports and can be classified into full, half and low contact styles. The aim of this study was the analysis of sports injuries in Kyokushinkai (full contact) and traditional Karate (semi-contact). In a retrospective study design, 215 active amateur karateka (114 full contact, 101 semi-contact) were interviewed by means of a standardised questionnaire regarding typical sport injuries during the last 36 months. Injuries were categorised into severity grade I (not requiring medical treatment), grade II (single medical treatment), grade III (several outpatient medical treatments) and grade IV (requiring hospitalisation). In total, 217 injuries were reported in detail. 125 injuries (58%) occurred in full contact and 92 (42%) in semi-contact karate. The time related injury rate of full contact karateka was 1.9/1000 h compared to 1.3/1000 h of semi-contact karateka (p < 0.05). The most common types of injuries were musculoskeletal contusions (33% full contact, 20% semi-contact), followed by articular sprains with 19% and 16%. The lower extremity was affected twice as often in full contact (40%) as in semi-contact (20%) karate. Training injuries were reported by 80% of the full contact and 77% of the semi-contact karateka. Most injuries, both in training and competition, occurred in kumite. 75% of the reported injuries of full contact and 70% of semi-contact karateka were classified as low grade (I or II). The high rate of injuries during training and kumite (sparring) points to specific prevention goals. The emphasis should be put on proprioceptive training and consistent warm-up. In the actual competition the referees play a vital role regarding prevention. © Georg Thieme Verlag KG Stuttgart · New York.

Overutilization of ambulatory medical care in the elderly German population?--An empirical study based on national insurance claims data and a review of foreign studies.

PubMed

van den Bussche, Hendrik; Kaduszkiewicz, Hanna; Schäfer, Ingmar; Koller, Daniela; Hansen, Heike; Scherer, Martin; Schön, Gerhard

2016-04-14

By definition, high utilizers receive a large proportion of medical services and produce relatively high costs. The authors report the results of a study on the utilization of ambulatory medical care by the elderly population in Germany in comparison to other OECD countries. Evidence points to an excessive utilization in Germany. It is important to document these utilization figures and compare them to those in other countries since the healthcare system in Germany stopped recording ambulatory healthcare utilization figures in 2008. The study is based on the claims data of all insurants aged ≥ 65 of a statutory health insurance company in Germany (n = 123,224). Utilization was analyzed by the number of contacts with physicians in ambulatory medical care and by the number of different practices contacted over one year. Criteria for frequent attendance were ≥ 50 contacts with practices or contacts with ≥ 10 different practices or ≥ 3 practices of the same discipline per year. Descriptive statistical analysis and logistic regression were applied. Morbidity was analyzed by prevalence and relative risk for frequent attendance for 46 chronic diseases. Nineteen percent of the elderly were identified as high utilizers, corresponding to approximately 3.5 million elderly people in Germany. Two main types were identified. One type has many contacts with practices, belongs to the oldest age group, suffers from severe somatic diseases and multimorbidity, and/or is dependent on long-term care. The other type contacts large numbers of practices, consists of younger elderly who often suffer from psychiatric and/or psychosomatic complaints, and is less frequently multimorbid and/or nursing care dependent. We found a very high rate of frequent attendance among the German elderly, which is unique among the OECD countries. Further research should clarify its reasons and if this degree of utilization is beneficial for elderly people.

Mucins in contact lens wear and dry eye conditions.

PubMed

Ramamoorthy, Padmapriya; Nichols, Jason J

2008-08-01

Ocular mucins are thought to play integral roles in ocular surface lubrication, anchoring of the aqueous, stabilizing the lipid components of the tear film, eliminating foreign bodies and pathogens, and with potential involvement in cell cycle mediation and apoptotic activity of ocular surface epithelia. Ocular mucins are of secreted and membrane-associated types. Secreted mucins may be of large gel-forming type or small soluble mucins (e.g., MUC5AC and MUC7). Membrane-associated mucins such as MUCs 1 and 4 are a major component of the glycocalyx. They are thought to render structural support to the microplicae and mediate epithelial cell cycle and apoptotic activity. The alterations in ocular mucins with contact lens wear are unclear. Recent work shows mucin expression may be up-regulated during the early years of contact lens wear, and with long-term lens wear, mucin expression may return to normal levels or sub-normal levels, although this is not well understood. Further, the polar nature of mucins may be associated with their affinity for contact lens surfaces making them a component of contact lens deposition. This has potential implications in the wettability and tolerability of contact lenses, and may be impacted by surface coatings, polymer characteristics, or care solutions. Conjunctival mucin gene expression and secretion may be deficient in several ocular surface disorders associated with dry eye. Deficiency and alterations in glycosylation characteristics of MUC5AC and MUC2 have been reported in both Sjögren and non-Sjögren dry eye types. Decreased binding of the membrane-associated mucin MUC16 to the conjunctival epithelium has been reported in Sjögren dry eye while MUC1 alterations have been reported in Sjögren and non-Sjögren dry eye states. In view of the mucin involvement in dry eye conditions, stimulation of mucus secretion pathways may hold promise in the pharmaceutical treatment of dry eye.

The Clusters AgeS Experiment (CASE). Variable Stars in the Field of the Globular Cluster NGC 6362

NASA Astrophysics Data System (ADS)

Kaluzny, J.; Thompson, I. B.; Rozyczka, M.; Pych, W.; Narloch, W.

2014-12-01

The field of the globular cluster NGC 6362 was monitored between 1995 and 2009 in a search for variable stars. BV light curves were obtained for 69 periodic variable stars including 34 known RR Lyr stars, 10 known objects of other types and 25 newly detected variable stars. Among the latter we identified 18 proper-motion members of the cluster: seven detached eclipsing binaries (DEBs), six SX Phe stars, two W UMa binaries, two spotted red giants, and a very interesting eclipsing binary composed of two red giants - the first example of such a system found in a globular cluster. Five of the DEBs are located at the turnoff region, and the remaining two are redward of the lower main sequence. Eighty-four objects from the central 9×9 arcmin2 of the cluster were found in the region of cluster blue stragglers. Of these 70 are proper motion (PM) members of NGC 6362 (including all SX Phe and two W UMa stars), and five are field stars. The remaining nine objects lacking PM information are located at the very core of the cluster, and as such they are likely genuine blue stragglers.

Occupational protein contact dermatitis from spices in a butcher: a new presentation of the mugwort-spice syndrome.

PubMed

Anliker, Mark David; Borelli, Siegfried; Wüthrich, Brunello

2002-02-01

Protein contact dermatitis to meat is well known in butchers; spices are another source of potential contact allergy and usually are not recognized. We present a first case of contact-dermatitis to spice mix in a 39-year-old-butcher. The patient underwent skin prick testing (SPT) with standard allergens (ALK) and different meat and spice extracts (Stallergènes), scratch-patch testing with spice mix containing glutamate, paprika and other spices. Specific serum-IgE was measured with CAP-FEIA. SPT only showed an immediate-type sensitization to mugwort (+ +), as well as different spices (paprika +, curry +, cumin +) and camomile (+ + +). Scratch-patch tests were negative for different meat, but strongly positive for spice mix (+ + +) after 30 min (wheal and flare) and (+ +) after 48 h (infiltration and vesiculation). Two healthy controls were tested negative for spice mix used from that patient (scratch-patch). Specific IgE was slightly elevated for paprika 0.47 kU/L (CAP class 1), anise 0.43 kU/L, curry 0.36 kU/L and mugwort 3.83 kU/L. Sx1 atopy-multiscreen was 3.8 kU/L due to a sensitization to mugwort alone. The tests performed demonstrate an IgE-mediated contact allergy to spices but also a delayed type allergy to spice mix as a manifestation of the mugwort-spice syndrome in this individual. When testing for occupational dermatitis in butchers, protein contact allergy to spices must also be taken into consideration.

ACHP | News

Science.gov Websites

taxpayer resources." Common bridge types like this concrete girder bridge will not require individual bridge types, including those covered by the Program Comment, check out the NCHRP Publication: "A Context for Common Historic Bridge Types." Please contact Carol Legard at 202-606-8522 or via e-mail

Tear analysis in contact lens wearers.

PubMed Central

Farris, R L

1985-01-01

Tear analysis in contact lens wearers was compared with tear analysis in aphakics without contact lens wear and normal phakic patients. Subjects were divided into five groups: group 1, aphakic without contact lens; group 2, phakic with daily-wear hard contact lens; group 3, phakic with daily-wear soft contact lens; group 4, phakic with extended-wear soft contact lens; and group 5, aphakic with extended-wear soft contact lens. The experimental groups were compared with age- and sex-matched control groups for statistical analysis of tear variables by means of the Student's t-test. The variables measured were tear osmolarity, tear albumin, and lysozyme and lactoferrin concentrations in basal and reflex tears. Highly significant elevations of tear osmolarity were found in aphakic subjects without contact lenses. Less significant differences in tear osmolarity were found in phakic subjects with hard daily-wear lenses or with extended-wear soft lenses. Tear albumin, lysozyme, and lactoferrin in basal and reflex tears were not significantly different in the different groups of contact lens wearers or in the group of aphakic subjects without contact lenses compared with their control groups. Individual variations in tear albumin, lysozyme, and lactoferrin appeared to be responsible for the inability to demonstrate significant differences in tear composition in association with the wearing of different types of contact lenses. Older and aphakic patients demonstrated a tendency to have increased concentrations of proteins in the tears compared with younger, phakic contact lens wearers and normal controls without contact lenses. PMID:3914131

A method for improved accuracy in three dimensions for determining wheel/rail contact points

NASA Astrophysics Data System (ADS)

Yang, Xinwen; Gu, Shaojie; Zhou, Shunhua; Zhou, Yu; Lian, Songliang

2015-11-01

Searching for the contact points between wheels and rails is important because these points represent the points of exerted contact forces. In order to obtain an accurate contact point and an in-depth description of the wheel/rail contact behaviours on a curved track or in a turnout, a method with improved accuracy in three dimensions is proposed to determine the contact points and the contact patches between the wheel and the rail when considering the effect of the yaw angle and the roll angle on the motion of the wheel set. The proposed method, with no need of the curve fitting of the wheel and rail profiles, can accurately, directly, and comprehensively determine the contact interface distances between the wheel and the rail. The range iteration algorithm is used to improve the computation efficiency and reduce the calculation required. The present computation method is applied for the analysis of the contact of rails of CHINA (CHN) 75 kg/m and wheel sets of wearing type tread of China's freight cars. In addition, it can be proved that the results of the proposed method are consistent with that of Kalker's program CONTACT, and the maximum deviation from the wheel/rail contact patch area of this two methods is approximately 5%. The proposed method, can also be used to investigate static wheel/rail contact. Some wheel/rail contact points and contact patch distributions are discussed and assessed, wheel and rail non-worn and worn profiles included.

Thermally stable ohmic contacts to n-type GaAs. VII. Addition of Ge or Si to NiInW ohmic contacts

NASA Astrophysics Data System (ADS)

Murakami, Masanori; Price, W. H.; Norcott, M.; Hallali, P.-E.

1990-09-01

The effects of Si or Ge addition to NiInW ohmic contacts on their electrical behavior were studied, where the samples were prepared by evaporating Ni(Si) or Ni(Ge) pellets with In and W and annealed by a rapid thermal annealing method. An addition of Si affected the contact resistances of NiInW contacts: the resistances decreased with increasing the Si concentrations in the Ni(Si) pellets and the lowest value of ˜0.1 Ω mm was obtained in the contact prepared with the Ni-5 at. % Si pellets after annealing at temperatures around 800 °C. The contact resistances did not deteriorate during isothermal annealing at 400 °C for more than 100 h, far exceeding process requirements for self-aligned GaAs metal-semiconductor field-effect-transistor devices. In addition, the contacts were compatible with TiAlCu interconnects which have been widely used in the current Si process. Furthermore, the addition of Si to the NiInW contacts eliminated an annealing step for activation of implanted dopants and low resistance (˜0.2 Ω mm) contacts were fabricated for the first time by a ``one-step'' anneal. In contrast, an addition of Ge to the NiInW contacts did not significantly reduce the contact resistances.