Ground resistivity method and DCIP2D forward and inversion modelling to identify alteration at the Midwest uranium deposit, northern Saskatchewan, Canada

NASA Astrophysics Data System (ADS)

Long, Samuel R. M.; Smith, Richard S.; Hearst, Robert B.

2017-06-01

Resistivity methods are commonly used in mineral exploration to map lithology, structure, sulphides and alteration. In the Athabasca Basin, resistivity methods are used to detect alteration associated with uranium. At the Midwest deposit, there is an alteration zone in the Athabasca sandstones that is above a uraniferous conductive graphitic fault in the basement and below a conductive lake at surface. Previous geophysical work in this area has yielded resistivity sections that we feel are ambiguous in the area where the alteration is expected. Resolve® and TEMPEST sections yield an indistinct alteration zone, while two-dimensional (2D) inversions of the ground resistivity data show an equivocal smeared conductive feature in the expected location between the conductive graphite and the conductive lake. Forward modelling alone cannot identify features in the pseudosections that are clearly associated with alteration, as the section is dominated by the feature associated with the near-surface conductive lake; inverse modelling alone produces sections that are smeared and equivocal. We advocate an approach that uses a combination of forward and inverse modelling. We generate a forward model from a synthetic geoelectric section; this forward data is then inverse modelled and compared with the inverse model generated from the field data using the same inversion parameters. The synthetic geoelectric section is then adjusted until the synthetic inverse model closely matches the field inverse model. We found that this modelling process required a conductive alteration zone in the sandstone above the graphite, as removing the alteration zone from the sandstone created an inverse section very dissimilar to the inverse section derived from the field data. We therefore conclude that the resistivity method is able to identify conductive alteration at Midwest even though it is below a conductive lake and above a conductive graphitic fault. We also concluded that resistivity inversions suggest a conductive paleoweathering surface on the top of the basement rocks at the basin/basement unconformity.

Percolation of diagenetic fluids in the Archaean basement of the Franceville basin

NASA Astrophysics Data System (ADS)

Mouélé, Idalina Moubiya; Dudoignon, Patrick; Albani, Abderrazak El; Cuney, Michel; Boiron, Marie-Christine; Gauthier-Lafaye, François

2014-01-01

The Palaeoproterozoic Franceville basin, Gabon, is mainly known for its high-grade uranium deposits, which are the only ones known to act as natural nuclear fission reactors. Previous work in the Kiéné region investigated the nature of the fluids responsible for these natural nuclear reactors. The present work focuses on the top of the Archaean granitic basement, specifically, to identify and date the successive alteration events that affected this basement just below the unconformity separating it from the Palaeoproterozoic basin. Core from four drill holes crosscutting the basin-basement unconformity have been studied. Dating is based on U-Pb isotopic analyses performed on monazite. The origin of fluids is discussed from the study of fluid inclusion planes (FIP) in quartz from basement granitoids. From the deepest part of the drill holes to the unconformable boundary with the basin, propylitic alteration assemblages are progressively replaced by illite and locally by a phengite + Fe chlorite ± Fe oxide assemblage. Illitic alteration is particularly strong along the sediment-granitoid contact and is associated with quartz dissolution. It was followed by calcite and anhydrite precipitation as fracture fillings. U-Pb isotopic dating outlines three successive events: a 3.0-2.9-Ga primary magmatic event, a 2.6-Ga propylitic alteration and a late 1.9-Ga diagenetic event. Fluid inclusion microthermometry suggests the circulation of three types of fluids: (1) a Na-Ca-rich diagenetic brine, (2) a moderately saline (diagenetic + meteoric) fluid, and (3) a low-salinity fluid of probable meteoric origin. These fluids are similar to those previously identified within the overlying sedimentary rocks of the Franceville basin. Overall, the data collected in this study show that the Proterozoic-Archaean unconformity has operated as a major flow corridor for fluids circulation, around 1.9 Ga. highly saline diagenetic brines; hydrocarbon-rich fluids derived from organic matter-rich formations; a low-salinity fluid likely of meteoric origin migrating through the granitic basement; mineralizing fluids resulting from the mixing of fluids 1 and 3; high-temperature fluids resulting from the natural nuclear reactor environment (Mathieu et al., 2000). The present paper attempts to characterize the succession of alteration events that have affected the top of the basement below the Palaeoproterozoic sediment unconformity. Are these alterations related to early post-magmatic to hydrothermal events, to palaeoweathering, or to late infiltration of diagenetic brines from the overlying basin? Our study, carried out on drill core samples from Kiéné, is supported by petrographic investigation, new fluid inclusion data and U-Pb geochronology on monazite.

Geology of uranium in the Chadron area, Nebraska and South Dakota

USGS Publications Warehouse

Dunham, Robert Jacob

1961-01-01

The Chadron area covers 375 square miles about 25 miles southeast of the Black Hills. Recurrent mild tectonic activity and erosion on the Chadron arch, a compound anticlinal uplift of regional extent, exposed 1900 feet of Upper Cretaceous rocks, mostly marine shale containing pyrite and organic matter, and 600 feet of Oligocene and Miocene rocks, mostly terrestrial fine-grained sediment containing volcanic ash. Each Cretaceous formation truncated by the sub-Oligocene unconformity is stained yellow and red, leached, kaolinized, and otherwise altered to depths as great as 55 feet. The composition and profile of the altered material indicate lateritic soil; indirect evidence indicates Eocene(?) age. In a belt through the central part of the area, the Brule formation of Oligocene age is a sequence of bedded gypsum, clay, dolomite, and limestone more than 300 feet thick. Uranium in Cretaceous shale in 58 samples averages 0.002 percent, ten times the average for the earths crust. Association with pyrite and organic matter indicates low valency. The uranium probably is syngenetic or nearly so. Uranium in Eocene(?) soil in 43 samples averages 0.054 percent, ranging up to 1.12 percent. The upper part of the soil is depleted in uranium; enriched masses in the basal part of the soil consist of remnants of bedrock shale and are restricted to the highest reaches of the ancient oxidation-reduction interface. The uranium is probably in the from of a low-valent mineral, perhaps uraninite. Modern weathering of Cretaceous shale is capable of releasing as much as 0.780 ppm uranium to water. Eocene(?) weathering probably caused enrichment of the ancient soil through 1) leaching of Cretaceous shale, 2) downward migration of uranyl complex ions, and 3) reduction of hydrogen sulfide at the water table. Uranium minerals occur in the basal 25 feet of the gypsum facies of the Brule formation at the two localities where the gypsum is carbonaceous; 16 samples average 0.066 percent uranium and range up to 0.43 percent. Elsewhere uranium in dolomite and limestone in the basal 25 feet of the gypsum facies in 10 samples averages 0.007 percent, ranging up to 0.12 percent. Localization of the uranium at the base of the gypsum facies suggests downward moving waters; indirect evidence that the water from which the gypsum was deposited was highly alkaline suggests that the uranium was leached from volcanic ash in Oligocene time.

Deciphering the mid-Carboniferous eustatic event in the central Appalachian foreland basin, southern West Virginia, USA

USGS Publications Warehouse

Blake, B.M.; Beuthin, J.D.

2008-01-01

A prominent unconformity, present across shallow shelf areas of the Euramerican paleoequatorial basins, is used to demark the boundary between the Mississippian and Pennsylvanian subsystems. This unconformity, the mid-Carboniferous eustatic event, is generally attributed to a major glacio-eustatic sea-level fall. Although a Mississippian-Pennsylvanian unconformity is recognized throughout most of the Appalachian region, the record of the mid-Carboniferous eustatic event in the structurally deepest part of the basin has been controversial. Based on early reports that suggested the most complete Pennsylvanian section was present in southern West Virginia, various conceptual depositional models postulated continuous sedimentation between the youngest Mississippian Bluestone Formation and the oldest Penn-sylvanian Pocahontas Formation. In contrast, tabular-erosion models envisioned axial drainage systems that evolved in response to changing basin dynamics. These models predicted a Mississippian-Pennsylvanian unconformity. All these models suffered from a lack of biostratigraphic control. The presence of a sub-Pocahontas paleovalley, herein named the Lashmeet paleovalley, has been confirmed in southern West Virginia. The Lashmeet paleovalley was incised over 35 m into Bluestone strata and filled by lithic sands derived from the Appalachian orogen to the northeast and east. The polygenetic Green Valley paleosol complex marks the Bluestone-Pocahontas contact on associated interfluves. Together, these features indicate a substantial period of subaerial exposure and argue strongly in favor of a Mississippian-Pennsylvanian unconformity. Paleontologic data from the Bluestone Formation, including marine invertebrates and conodonts from the marine Bramwell Member and paleofloral data, support a late, but not latest, Arnsbergian age assignment. Marine fossils are not known from the Pocahontas Formation, but macrofloral and palynomorph taxa support a Langsettian age for most of the Poca-hontas. The biostratigraphic, sedimentologic, and paleogeographic data support the presence of an early Pennsylvanian (middle to late Namurian) disconformity in the Appalachian Basin that corresponds to the mid-Carboniferous eustatic event. ?? 2008 Geological Society of America.

Unconformity-related oil entrapment in Muddy Sandstone: comparison of Kitty and Amos Draw fields, Powder River basin, Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Odland, S.K.; Gardner, M.H.; Gustason, E.R.

1986-08-01

It has long been known that an unconformity plays a critical role in trapping oil in the Muddy Sandstone in the Powder River basin, but opinions have varied as to exactly where in the section that unconformity is located. Their work indicates that there are, in fact, two unconformities associated with the Muddy in the northern part of the basin. The older of these occurs on top of the Skull Creek Shale, whereas the younger is largely intraformational. In places, the younger unconformity has truncated the older one. It is the younger unconformity that is responsible for creating favorable settingsmore » for stratigraphic entrapment of oil. Two types of unconformity-related oil traps result from fluvial downcutting into and through the strand-plain sandstones of the oldest member of the Muddy during a major sea level drop. In cases where the unconformity cuts through the Muddy into the underlying Skull Creek Shale, permeable valley-fill sediments, deposited during the Muddy transgression, are juxtaposed against the impermeable Skull Creek Shale along the valley walls. Where valleys are oriented roughly perpendicular to regional structure, as at Kitty field, the updip portion of the valley wall can form a permeability barrier to the fluvial reservoir sandstones of the adjacent valley fill. In cases where the unconformity is intraformational, such as at Amos Draw field, early diagenetic clay, associated with the weathered horizon directly beneath the unconformity, can create a seal on top of the strand-plain sandstones of the oldest member of the Muddy.« less

Reconnaissance geology of the Ghazzalah Quadrangle, sheet 26/41 A, Kingdom of Saudi Arabia

USGS Publications Warehouse

Quick, James E.

1983-01-01

The Ghazzalah quadrangle is located in the northern Precambrian shield of Saudi Arabia between lat 26?30' and 27?00' N. and long 41?00' and 41?30' E. The area is underlain by two lithologically distinct, Precambrian volcanosedimentary units and a wide range of dioritoid and granitoid plutonic intrusive rocks. The only Phanerozoic rocks consist of one outcrop of Tertiary(?) basalt and widespread but thin deposits of Quaternary detritus. The Banana greenstone, the oldest rock in the quadrangle, consists of intermediate volcanic and subvolcanic rocks and minor interbedded marble, which have been metamorphosed to greenschist-facies assemblages. Volcanic rocks mainly range in composition from basalt to andesite, and subvolcanic rocks consist of diorite and diabase. The Banana greenstone is unconformably overlain by silicic volcanic rocks and minor arkosic sandstone and breccia of the Hadn formation. Preservation of delicate volcanic textures suggests that the rocks have been only incipiently metamorphosed. Unpublished rubidium/strontium isotopic data for the Hadn formation suggest an age of 620 to 610 Ma. Intrusive rocks are separable according to their ages relative to the Hadn formation. Those that are unconformably overlain by the Hadn formation consist of hornblende quartz diorite and gabbro, which may be consanguineous with the Banana greenstone, and younger tonalite, biotite-hornblende granodiorite, syenogranite, and monzogranite. Plutons of monzogranite, alkali-feldspar g,ranite, syenbgranite, peralkaline granite, and hypabyssal intrusions of granophyre were probably emplaced during a period coincident with and (or) following Hadn volcanism. Uranium-lead and rubidium/strontium isotopic data for two plutons in the adjacent Al Qasr quadrangle suggest that plutonic activity persisted in the region until about 580 to 570 Ma. Faulting appears to postdate all of the plutonic rocks. The dominant faults belong to a northeast-trending system of right-lateral shears; a subordinant system consists of mainly north- to northwest-trending faults. The peralkaline-granite plutons underlying Jibal Ba'gham and Jibal ar Rumman have the most economic potential. Wadi samples from these areas show an anomalous concentrations of tin, lead, niobium, and yttrium. Localized, intense radiometric anomalies in the Ba'gham intrusive complex are associated with high concentrations )f thorium, uranium, andrare-earth elements.

Development of multiple unconformities during the Devonian-Carboniferous transition on parts of Laurussia

USGS Publications Warehouse

Ettensohn, F.R.; Pashin, J.C.

1997-01-01

The Devonian-Carboniferous transition on Laurussia was a time of diverse geologic activity associated with the assembly of Pangea, including episodes of Late Devonian glacial-eustatic lowstand and active orogeny on four margins. Six widespread unconformities are present in the Devonian-Carboniferous (Mississippian) interval on southern parts of Laurussia. We suggest that attention to the timing and plan of the unconformities may provide ways of discerning tectonic and climatic controls on their respective origins. Indeed, unconformities generated by pure eustasy are ideally of interregional extent, whereas unconformities generated by tectonism reflect more local factors associated with the evolution of sedimentary basins. Each of the six unconformities analyzed provides evidence for concurrent eustasy and tectonism. Glaciation was apparently the dominant factor driving the development of unconformities during the latest Devonian. During the Early Carboniferous, however, the volume of glacial ice available to drive eustasy was limited and, at times, tectonism may have been the source of a subordinate eustatic signal. Development of unconformities in southern Laurussia appear to be local manifestations of tectonic and climatic processes associated with supercontinent assembly. Thus, the time may be at hand for construction of a new global stratigraphic paradigm that is based on the plate tectonic supercycle affecting continentality and climate.

Integrated geophysical and geological study and petroleum appraisal of Cretaceous plays in the Western Gulf of Gabes, Tunisia

NASA Astrophysics Data System (ADS)

Dkhaili, Noomen; Bey, Saloua; El Abed, Mahmoud; Gasmi, Mohamed; Inoubli, Mohamed Hedi

2015-09-01

An integrated study of available seismic and calibrated wells has been conducted in order to ascertain the structural development and petroleum potential of the Cretaceous Formations of the Western Gulf of Gabes. This study has resulted in an understanding of the controls of deep seated Tethyan tectonic lineaments by analysis of the Cretaceous deposits distribution. Three main unconformities have been identified in this area, unconformity U1 between the Jurassic and Cretaceous series, unconformity U2 separating Early from Late Cretaceous and known as the Austrian unconformity and the major unconformity U3 separating Cretaceous from Tertiary series. The seismic analysis and interpretation have confirmed the existence of several features dominated by an NE-SW extensive tectonic regime evidenced by deep listric faults, asymmetric horst and graben and tilted blocks structures. Indeed, the structural mapping of these unconformities, displays the presence of dominant NW-SE fault system (N140 to N160) bounding a large number of moderate sized basins. A strong inversion event related to the unconformity U3 can be demonstrated by the mapping of the unconformities consequence of the succession of several tectonic manifestations during the Cretaceous and post-Cretaceous periods. These tectonic events have resulted in the development of structural and stratigraphic traps further to the porosity and permeability enhancement of Cretaceous reservoirs.

Seismic stratigraphy of sedimentary cover in Amerasian Basin based on the results of Russian High Arctic expeditions

NASA Astrophysics Data System (ADS)

Poselov, Viktor; Kireev, Artem; Smirnov, Oleg; Butsenko, Viktor; Zholondz, Sergey; Savin, Vasily

2016-04-01

Massive amount of multichannel seismic (MCS) data were obtained by Russian High Arct ic expeditions "Arctica-2011", "Acrtica-2012" and "Arctica-2014". More than 40 MCS lines are located in the Amerasian basin and help to substantiate the seismic stratigraphy model of its sedimentary cover. The proposed seismic stratigraphy model was successively determined for the Cenozoic and pre-Cenozoic parts of the sedimentary section and was based on correlation of the Russian MCS data and seismic data documented by boreholes. Cenozoic part of the sedimentary cover is based on correlation of the Russian MCS data and AWI91090 section calibrated by ACEX-2004 boreholes on the Lomonosov Ridge. Two major unconformities are traced. The upper regional unconformity (RU) is associated with a major pre-Miocene hiatus. Another major hiatus is recorded in the borehole section between the Campanian and the Upper Paleocene units. It is recognized as the post-Campanian unconformity (pCU) in the seismic sections. Formation of the regional unconformities is associated with a fundamental change in depositional environment. Formation of RU was initiated by opening of the Fram Strait gateway at the Paleogene/Neogene boundary. Post-Campanian unconformity is linked with the initial stage of the Eurasian Basin opening between the Cretaceous and the Paleogene. Cenozoic sedimentary units are continuously traced from the East-Siberian and Chukchi sea shelves across the transit zone to the Amerasian basin. Paleogene unit (between pCU and RU) is formed under the neritic depositional environment and it is characterized by an extremely small thickness on the Lomonosov Ridge (less than 200 m), on the Mendeleev Rise and in the Podvodnikov Basin (not more than 300-400 m). Neogene unit (above RU) consists of hemipelagic deposits and occupies the essential part of thickness of the Cenozoic section in Podvodnikov and Makarov Basins. Interval velocities in the Paleogene unit vary within 2.8-3.2 km/s, in the Neogene unit they vary within 1.8-2.7 km/s. Pre-Cenozoic part of the sedimentary cover is based on tracing major unconformities from boreholes on the Chukchi shelf (Crackerjack, Klondike, Popcorn) to the North-Chuckchi Trough and further to the Mendeleev Rise as well as to the Vilkitsky Trough and the adjacent Podvodnikov Basin. Three regional unconformities are correlated: Jurassic (JU - top of the Upper Ellesmerian unit), Lower Cretaceous (LCU) and Brookian (BU - base of the Lower Brookian unit). Above the acoustic basement the pre-Cenozoic section is mainly represented by terrigenous units. Two major unconformities: RU and pCU are allocated on all MCS lines intersecting the Mendeleev Rise along its entire extent. BU is traced nearly everywhere along the rise excepting certain acoustic basement highs. All unconformities are also traced from the Mendeleev Rise to the continental structure of the Chuckchi Borderland. Sedimentary sequence between pCU and JU which underlies deposits of the Upper Ellesmerian unit is recorded as a synrift unit of the entire area of the Podvodnikov Basin. MCS data show a natural prolongation of the sedimentary cover from the shelf to the Podvodnikov Basin without any breaks and tectonic movements. Interval velocities in the Upper Cretaceous unit (between pCU and BU) vary within 3.2-3.9 km/s, in the pre-Upper Cretaceous units (between BU and the acoustic basement) vary within 4.1-4.8 km/s.

Miocene unconformities in the Central Apennines: geodynamic significance and sedimentary basin evolution

NASA Astrophysics Data System (ADS)

Cipollari, Paola; Cosentino, Domenico

1995-12-01

This paper shows the results obtained from an integrated study (geology, biostratigraphy and geochemistry) carried out on the Miocene edimentary deposits in Central Italy in order to define the timing of the sedimentary basin evolution. This paper deals also with the causes of the unconformities recorded in these basins. In the Miocene deposits of the Latina Valley and the Ernici-Simbruini Mts. several unconformities which distinguish different stratigraphic sequences have been recognized (D 0, D 1, D 2 D 3 and D 4). For each unconformity a general description together with a geodynamical significance is provided. In particular, D 0 unconformity appears to be related to a regional tectonic event (Adria-Europe collision). As a consequence, the Adria lithosphere folded and the area underwent a regional erosive event. D 1, D 2 and D 3 unconformities have had a more local tectonic control since they represent the stratigraphic record of the migration of the Apennines thrust belt/foredeep system. D 1 and D 2 unconformities are related to the late Tortonian foredeep stage, whereas D 3 is linked to the early Messinian piggy-back stage. Moreover, the D 4 unconformity, which took place during the Messinian piggy-back stage, is strictly linked to the sea-level drop of the Messinian salinity crisis. In this paper the genesis and evolution of a late Tortonian foreland basin is also stressed (Latina Valley foredeep basin). Finally, taking into account sequence boundaries, nannofossil biostratigraphy and geochemistry isotopic data, a comparison with the curve of the 3rd order of the relative coastal onlap (Haq et al., 1988) has been attempted in order to distinguish the unconformities controlled either by tectonic or eustatic processes.

Age and paragenesis of mineralisation at Coronation Hill uranium deposit, Northern Territory, Australia

NASA Astrophysics Data System (ADS)

Orth, Karin; Meffre, Sebastien; Davidson, Garry

2014-06-01

Coronation Hill is a U + Au + platinum group elements deposit in the South Alligator Valley (SAV) field in northern Australia, south of the better known unconformity-style U East Alligator Rivers (EAR) field. The SAV field differs from the EAR by having a more complex basin-basement architecture. A volcanically active fault trough (Jawoyn Sub-basin) developed on older basement and then was disrupted by renewed faulting, before being buried beneath regional McArthur Basin sandstones that are also the main hanging wall to the EAR deposits. Primary mineralisation at Coronation Hill formed at 1607 ± 26 Ma (rather than 600-900 Ma as previously thought), and so it is likely that the SAV was part of a single west McArthur Basin dilational event. Most ore is hosted in sub-vertical faults and breccias in the competent volcanic cover sequence. This favoured fluid mixing, acid buffering (forming illite) and oxidation of Fe2+ and reduced C-rich assemblages as important uranium depositional mechanisms. However, reduction of U in fractured older pyrite (Pb model age of 1833 ± 67 Ma) is an important trap in diorite. Some primary ore was remobilised at 675 ± 21 Ma to form coarse uraninite + Ni-Co pyrite networks containing radiogenic Pb. Coronation Hill is polymetallic, and in this respect resembles the `egress'-style U deposits in the Athabascan Basin (Canada). However, these are all cover-hosted. A hypothesis for further testing is that Coronation Hill is also egress-style, with ores formed by fluids rising through basement-hosted fault networks (U reduction by diorite pyrite and carbonaceous shale), and into veins and breccias in the overlying Jawoyn Sub-basin volcano-sedimentary succession.

Re-evaluation of the petrogenesis of the Proterozoic Jabiluka unconformity-related uranium deposit, Northern Territory, Australia

NASA Astrophysics Data System (ADS)

Polito, Paul A.; Kurt Kyser, T.; Thomas, David; Marlatt, Jim; Drever, Garth

2005-11-01

The world class Jabiluka unconformity-related uranium deposit in the Alligator Rivers Uranium Field, Australia, contains >163,000 tons of contained U3O8. Mineralization is hosted by shallow-to-steeply dipping basement rocks comprising graphitic units of chlorite-biotite-muscovite schist. These rocks are overlain by flat-lying coarse-grained sandstones belonging to the Kombolgie Subgroup. The deposit was discovered in 1971, but has never been mined. The construction of an 1,150 m decline into the upper eastern sector of the Jabiluka II deposit combined with closely spaced underground drilling in 1998 and 1999 allowed mapping and sampling from underground for the first time. Structural mapping, drill core logging and petrographic studies on polished thin sections established a detailed paragenesis that provided the framework for subsequent electron microprobe and X-ray diffraction, fluid inclusion, and O-H, U-Pb and 40Ar/39Ar isotope analysis. Uranium mineralization is structurally controlled within semi-brittle shears that are sub-conformable to the basement stratigraphy, and breccias that are developed within the hinge zone of fault-related folds adjacent to the shears. Uraninite is intimately associated with chlorite, sericite, hematite ± quartz. Electron microprobe and X-ray diffraction analysis of syn-ore illite and chlorite indicates a mineralization temperature of 200°C. Pre- and syn-ore minerals extracted from the Kombolgie Subgroup overlying the deposit and syn-ore alteration minerals in the Cahill Formation have δ18Ofluid and δ D fluid values of 4.0±3.7 and -27±17‰, respectively. These values are indistinguishable from illite separates extracted from diagenetic aquifers in the Kombolgie Subgroup up to 70 km to the south and east of the deposit and believed to be the source of the uraniferous fluid. New fluid inclusion microthermometry data reveal that the mineralising brine was saline, but not saturated. U-Pb and 207Pb/206Pb ratios of uraninite by laser-ablation ICP-MS suggest that massive uraninite first precipitated at ca. 1,680 Ma, which is coincident with the timing of brine migration out from the Kombolgie Subgroup as indicated by 40Ar/39Ar ages of 1,683±11 Ma from sandstone-hosted illite. Unmineralized breccias cemeted by chlorite, quartz and sericite cross-cut the mineralized breccias and are in turn cut by straight-sided, high-angle veins of drusy quartz, sulphide and dolomite. U-Pb and 207Pb/206Pb ratios combined with fluid inclusion and stable isotope data indicate that these post-ore minerals formed when mixing between two fluids occurred sometime between ca. 1,450 and 550 Ma. Distinct 207Pb/206Pb age populations occur at ca. 1,302±37, 1,191±27 and 802±57 Ma, which respectively correlate with the intrusion of the Maningkorrirr/Mudginberri phonolitic dykes and the Derim Derim Dolerite between 1,370 and 1,316 Ma, the amalgamation of Australia and Laurentia during the Grenville Orogen at ca. 1,140 Ma, and the break-up of Rodinia between 1,000 and 750 Ma.

2D and 3D separate and joint inversion of airborne ZTEM and ground AMT data: Synthetic model studies

NASA Astrophysics Data System (ADS)

Sasaki, Yutaka; Yi, Myeong-Jong; Choi, Jihyang

2014-05-01

The ZTEM (Z-axis Tipper Electromagnetic) method measures naturally occurring audio-frequency magnetic fields and obtains the tipper function that defines the relationship among the three components of the magnetic field. Since the anomalous tipper responses are caused by the presence of lateral resistivity variations, the ZTEM survey is most suited for detecting and delineating conductive bodies extending to considerable depths, such as graphitic dykes encountered in the exploration of unconformity type uranium deposit. Our simulations shows that inversion of ZTEM data can detect reasonably well multiple conductive dykes placed 1 km apart. One important issue regarding ZTEM inversion is the effect of the initial model, because homogeneous half-space and (1D) layered structures produce no responses. For the 2D model with multiple conductive dykes, the inversion results were useful for locating the dykes even when the initial model was not close to the true background resistivity. For general 3D structures, however, the resolution of the conductive bodies can be reduced considerably depending on the initial model. This is because the tipper magnitudes from 3D conductors are smaller due to boundary charges than the 2D responses. To alleviate this disadvantage of ZTEM surveys, we combined ZTEM and audio-frequency magnetotelluric (AMT) data. Inversion of sparse AMT data was shown to be effective in providing a good initial model for ZTEM inversion. Moreover, simultaneously inverting both data sets led to better results than the sequential approach by enabling to identify structural features that were difficult to resolve from the individual data sets.

In Review (Geology): Alpine Landscape Evolution Dominated by Cirque Retreat

NASA Technical Reports Server (NTRS)

Oskin, Michael; Burbank, Doug

2005-01-01

Despite the abundance in alpine terrain of glacially dissected landscapes, the magnitude and geometry of glacial erosion can rarely be defined. In the eastern Kyrgyz Range, a widespread unconformity exhumed as a geomorphic surface provides a regional datum with which to calibrate erosion. As tectonically driven surface uplift has progressively pushed this surface into the zone of ice accumulation, glacial erosion has overprinted the landscape. With as little as 500 m of incision into rocks underlying the unconformity, distinctive glacial valleys display their deepest incision adjacent to cirque headwalls. The expansion of north-facing glacial cirques at the expense of south-facing valleys has driven the drainage divide southwards at rates up to 2 to 3 times the rate of valley incision. Existing ice-flux-based glacial erosion rules incompletely model expansion of glacial valleys via cirque retreat into the low-gradient unconformity remnants. Local processes that either directly sap cirque headwalls or inhibit erosion down-glacier appear to control, at least initially, alpine landscape evolution.

Arctic Ocean Sedimentary Cover Structure, Based on 2D MCS Seismic Data.

NASA Astrophysics Data System (ADS)

Kireev, A.; Kaminsky, V.; Poselov, V.; Poselova, L.; Kaminsky, D.

2016-12-01

In 2016 the Russian Federation has submitted its partial revised Submission for establishment of the OLCS (outer limit of the continental shelf) in the Arctic Ocean. In order to prepare the Submission, in 2005 - 2014 the Russian organizations carried out a wide range of geological and geophysical studies, so that today over 23000 km of MCS lines and 4000 km of deep seismic sounding are accomplished. For correct time/depth conversion of seismic sections obtained with a short streamer in difficult ice conditions wide-angle reflection/refraction seismic sonobuoy soundings were used. All of these seismic data were used to refine the stratigraphy model, to identify sedimentary complexes and to estimate the total thickness of the sedimentary cover. Seismic stratigraphy model was successively determined for the Cenozoic and pre-Cenozoic parts of the sedimentary section and was based on correlation of the Russian MCS data and seismic data documented by boreholes. Cenozoic part of the sedimentary cover is based on correlation of the Russian MCS data and AWI91090 section calibrated by ACEX-2004 boreholes on the Lomonosov Ridge for Amerasia basin and by correlation of onlap contacts onto oceanic crust with defined magnetic anomalies for Eurasia basin. Pre-Cenozoic part of the sedimentary cover is based on tracing major unconformities from boreholes on the Chukchi shelf (Crackerjack, Klondike, Popcorn) to the North-Chuckchi Trough and further to the Mendeleev Rise as well as to the Vilkitsky Trough and the adjacent Podvodnikov Basin. Six main unconformities were traced: regional unconformity (RU), Eocene unconformity (EoU) (for Eurasia basin only), post-Campanian unconformity (pCU), Brookian (BU - base of the Lower Brookian unit), Lower Cretaceous (LCU) and Jurassic (JU - top of the Upper Ellesmerian unit). The final step in our research was to generalize all seismic surveys (top of acoustic basement correlation data) and bathymetry data in the sedimentary cover thickness map of the Arctic Ocean and adjacent Eurasian shelf, on which the structural prolongation of the shallow shelf into deep-water is obviously seen.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Handford, C.R.

Exploration is increasingly dependent upon obtaining credible stratigraphic interpretations of seismic data. With respect to carbonate platforms, two of the most important seismic-imaging and interpretation problems are (1) distinguishing between lowstand unconformities and drowning unconformities, and (2) recognizing paleokarst reservoirs. Lowstand unconformities vs. drowning unconformities. Many contend that onlapping wedges of strata above sequence boundaries but below the previous shelf break comprise the lowstand systems tract. An alternative view is that onlapping wedges do not record sea level falls, but instead chronicle sea level rises and platform demise. A Mississippian carbonate ramp exposed along the southern margin of North Americamore » is flanked by a siliciclastic lowstand wedge and overlain by a drowning succession of black shales. This dual history of lowstand exposure and drowning formed two baselap surfaces, which lie so close to each other on the shelf that seismic dissemination is almost impossible. The paradox is that although the ramp was terminated by drowning, the visible seismic baselap was due to low-stand exposure. Numerous large fields around the world produce from carbonate reservoirs with a moderate to strong paleokarst overprint. Their discoveries, however, were structurally driven and rarely based upon predrill knowledge of paleokarst systems. In fact, there has been little effort to determine how to recognize paleocave systems in seismic reflection data. To narrow this gap, the sedimentary fill and stratal geometries of modern cave systems were examined and modeled seismically. The models show a passage from continuous reflections in the undisturbed country rock to discontinuous reflections inclined toward the cavern core. Velocity pull-ups and pull-downs are significant where velocity and density contrasts between the country rock and collapsed chamber are important.« less

The stratigraphy of the Steep Rock Group, N.W. Ontario, with evidence of a major unconformity

NASA Technical Reports Server (NTRS)

Wilks, M. E.; Nisbet, E. G.

1986-01-01

The Steep Rock Group is exposed 6 km north of Atikokan, 200 km west of Thunder Bay. It is situated on the southern margin of the Wabigoon Belt of the Archaean Superior Province, N. W. Ontario. Reinvestigation of the geology of the Group has shown that the Group lies unconformably on the Tonalite Complex to the east. This unconformity has been previously suspected, from regional and ine mapping but no conclusive outcrop evidence for its existence has as yet been published. The strike of the group, comprised of Basal Conglomerate, Carbonate Member, Ore Zone and Ashrock is generally north-northwest dipping steeply to the southwest. Of the 7 contacts between the Steep Rock Group and the Tonalite Complex, 3 expose the unconformity (The Headland, S. Roberts Pit, Trueman Point), and 4 are faulted. These three outcrops demonstrate unequivocally that the Steep Rock group was laid down unconformably on the underlying Tonalite Complex, which is circa 3 Ga old.

3D implicit modeling of the Sishen Mine: new resolution of the geometry and origin of Fe mineralization

NASA Astrophysics Data System (ADS)

Stoch, B.; Anthonissen, C. J.; McCall, M.-J.; Basson, I. J.; Deacon, J.; Cloete, E.; Botha, J.; Britz, J.; Strydom, M.; Nel, D.; Bester, M.

2017-12-01

The Sishen deposit is one of the largest iron ore concentrations in current production. Hematite mineralization occurs along a strike length of 14 km, with a width of 3.2 km and a maximum vertical extent of 400 m below the original surface. The 986-Mt reserve incorporates a suite of individual orebodies, beneath a locally preserved tectonized unconformity, with a wide range of geometries, depths, and orientations. Fully constrained, implicit 3D modeling of the entire mining volume (> 70 km3), was undertaken to the original, pre-mining topography. The model incorporates 5287 mapping points and > 21,000 drillholes and provides exceptional insight into the original configuration of ore and its relationship to contacts, unconformities, and structures in the enclosing country rock. The bulk of ore occurs to the west of a strike-extensive, partially inverted normal fault (Sloep Fault), within an asymmetrical synclinal structure on its western flank. This linear, N-S distribution of deep, thick ore is punctuated by palaeosinkholes, wherein base-of-ore dips of greater than 45°, are concentrically arranged. Localized ore volumes also occur along faults and in fault-bounded, downthrown blocks, to the north of NW-SE- and NE-SW-trending strike-slip faults that show relatively minor uplift to the south, probably due to the Lomanian Namaqua-Natal Orogeny. The revised model demonstrates the proximity of ore to a tectonized unconformity and highlights the structural control on ore volumes, implying that Fe mineralization at Sishen cannot be exclusively attributed to supergene enrichment and concentric palaeosinkhole formation.

Permo Triassic unconformity-related Au-Pd mineralisation, South Devon, UK: new insights and the European perspective

NASA Astrophysics Data System (ADS)

Shepherd, Tom J.; Bouch, Jon E.; Gunn, Andrew G.; McKervey, John A.; Naden, Jonathan; Scrivener, Richard C.; Styles, Michael T.; Large, Duncan E.

2005-07-01

An integrated mineralogical-geochemical study of unconformity-related Au-Pd occurrences within and around the Permo Triassic basins of southwest England, UK, has confirmed the importance of low temperature (86±13°C), hydrothermal carbonate veins as hosts for the mineralisation. Fluid inclusion data for the carbonate gangue, supported by stable isotope (13C and 18O) and radiogenic (87Sr/86Sr) data, have identified three principal fluids: (1) a reducing calcic brine [>25 wt% salinity, <0.5 NaCl/(NaCl+CaCl2)] originating in the sub-unconformity basement and an expression of advanced mineral fluid interaction; (2) an oxidising sodic brine [~16 wt% salinity, >0.9 NaCl/(NaCl+CaCl2)] originating in the post-unconformity red beds under evaporitic conditions, and (3) an oxygenated, low salinity groundwater (<3 wt% salinity). The sodic brine is reasoned to be the parent metalliferous fluid and to have acquired its enrichment in Au and Pd by the leaching of immature sediments and intra-rift volcanic rocks within the local Permo Triassic basins. Metal precipitation is linked to the destabilisation of Au and Pd chloride complexes by either mixing with calcic brines, dilution by groundwaters or interaction with reduced lithologies. This explains the diversity of mineralised settings below and above the unconformity and their affinity with red bed brines. The paucity of sulphide minerals, the development of selenides (as ore minerals and as mineral inclusion in gold grains), the presence of rhodochrosite and manganoan calcites (up to 2.5 wt% Mn in calcite) and the co-precipitation of hematite and manganese oxides are consistent with the overall high oxidation state of the ore fluids. A genetic model is proposed linking Permo Triassic red beds, the mixing of oxidising and reducing brines, and the development of unconformity-related precious metal mineralisation. Comparison with other European Permo Triassic basins reveals striking similarities in geological setting, mineralogy and geochemistry with Au, Au-Pd and selenide occurrences in Germany (Tilkerode, Korbach-Goldhausen), Poland (Lubin) and the Czech Republic (Svoboda nad Úpou and Stupná). Though the known Au-Pd occurrences are sub-economic, several predictive criteria are proposed for further exploration.

Stratigraphic framework and evolution of the Cretaceous continental sequences of the Bauru, Sanfranciscana, and Parecis basins, Brazil

NASA Astrophysics Data System (ADS)

Batezelli, Alessandro; Ladeira, Francisco Sergio Bernardes

2016-01-01

With the breakup of the supercontinent Gondwana, the South American Plate has undergone an intense process of tectonic restructuring that led to the genesis of the interior basins that encompassed continental sedimentary sequences. The Brazilian Bauru, Sanfranciscana and Parecis basins during Late Cretaceous have had their evolution linked to this process of structuring and therefore have very similar sedimentary characteristics. The purpose of this study is to establish a detailed understanding of alluvial sedimentary processes and architecture within a stratigraphic sequence framework using the concept of the stratigraphic base level or the ratio between the accommodation space and sediment supply. The integration of the stratigraphic and facies data contributed to defining the stratigraphic architecture of the Bauru, Sanfranciscana and Parecis Basins, supporting a model for continental sequences that depicts qualitative changes in the sedimentation rate (S) and accommodation space (A) that occurred during the Cretaceous. This study discusses the origin of the unconformity surfaces (K-0, K-1 and K-1A) that separate Sequences 1, 2A and 2B and the sedimentary characteristics of the Bauru, Sanfranciscana and Parecis Basins from the Aptian to the Maastrichtian, comparing the results with other Cretaceous Brazilian basins. The lower Cretaceous Sequence 1 (Caiuá and Areado groups) is interpreted as a low-accommodation systems tract compound by fluvial and aeolian systems. The upper Cretaceous lacustrine, braided river-dominated alluvial fan and aeolian systems display characteristics of the evolution from high-to low-accommodation systems tracts (Sequences 2A and 2B). Unconformity K-0 is related to the origin of the Bauru Basin itself in the Early Cretaceous. In Sanfranciscana and Parecis basins, the unconformity K-0 marks the contact between aeolian deposits from Lower Cretaceous and Upper Cretaceous alluvial systems (Sequences 1 and 2). Unconformity K-1, which was generated in the Late Cretaceous, is related to an increase of the A/S ratio, whereas Unconformity K-1A is the result of the decrease in the A/S ratio. Unconformity K-1A bound Sequence 2A (lacustrine and fluvial systems) and Sequence 2B (alluvial deposits) in Bauru Basin whereas in the Sanfranciscana and Parecis basins this unconformity marks the transition from alluvial system to aeolian system (Sequences 2A and 2B). Changes in depositional style in both basins correspond to two distinct tectonic moments occurring within the South American plate. The first associated with post-volcanic thermal subsidence of the Early Cretaceous (Serra Geral and Tapirapuã volcanismos), and the second moment associated with the uplift occurred in the Late Cretaceous (Alto Paranaíba, Vilhena and Serra Formosa Arcs).

Sedimentary Cover of the Central Arctic

NASA Astrophysics Data System (ADS)

Kireev, Artem; Poselov, Viktor; Butsenko, Viktor; Smirnov, Oleg

2017-04-01

Partial revised Submission of the Russian Federation for establishment of the OLCS (outer limit of the continental shelf) in the Arctic Ocean is made to include in the extended continental shelf of the Russian Federation, in accordance with article 76 of the Convention, the seabed and its subsoil in the central Arctic Ocean which is natural prolongation of the Russian land territory. To submit partial revised Submission in 2016, in 2005 - 2014 the Russian organizations carried out a wide range of geophysical studies, so that today over 23000 km of MCS lines, over hundreds of wide-angle reflection/refraction seismic sonobuoy soundings and 4000 km of deep seismic sounding are accomplished. All of these MCS and seismic soundings data were used to establish the seismic stratigraphy model of the Arctic region. Stratigraphy model of the sedimentary cover was successively determined for the Cenozoic and pre-Cenozoic parts of the section and was based on correlation of the Russian MCS data and seismic data documented by existing boreholes. Interpretation of the Cenozoic part of the sedimentary cover was based on correlation of the Russian MCS data and AWI91090 section calibrated by ACEX-2004 boreholes on the Lomonosov Ridge for Amerasia basin and by correlation of onlap contacts onto oceanic crust with defined magnetic anomalies for Eurasia basin, while interpretation of the Pre-Cenozoic part of the sedimentary cover was based on correlation with MCS and boreholes data from Chukchi sea shelf. Six main unconformities were traced: regional unconformity (RU), Eocene unconformity (EoU) (for Eurasia basin only), post-Campanian unconformity (pCU), Brookian (BU - base of the Lower Brookian unit), Lower Cretaceous (LCU) and Jurassic (JU - top of the Upper Ellesmerian unit). The final step in our research was to estimate the total thickness of the sedimentary cover of the Arctic Ocean and adjacent Eurasian shelf using top of acoustic basement correlation data and bathymetry data. Structural prolongation of the shallow shelf into deep-water could be observed on this sedimentary map.

Analysis of some seismic expressions of Big Injun sandstone and its adjacent interval

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiangdong, Zou; Wilson, T.A.; Donaldson, A.C.

1991-08-01

The Big Injun sandstone is an important oil and gas reservoir in western West Virginia. The pre-Greenbrier unconformity has complicated correlations, and hydrocarbon explorationists commonly have misidentified the Big Injun in the absence of a regional stratigraphic study. Paleogeologic maps on this unconformity show the West Virginia dome, with the Price/Pocono units truncated resulting in pinch-outs of different sandstones against the overlying Big Lime (Greenbrier Limestone). Drillers have named the first sandstone below the Big Lime as Big Injun, and miscorrelated the real Big Injun with Squaw, upper Weir, and even the Berea sandstone. In this report, an 8-mi (13-km)more » seismic section extending from Kanawha to Clay counties was interpreted. The study area is near the pinch-out of the Big Injun sandstone. A stratigraphic cross section was constructed from gamma-ray logs for comparison with the seismic interpretation. The modeling and interpretation of the seismic section recognized the relief on the unconformity and the ability to determine facies changes, too. Both geophysical wireline and seismic data can be used for detailed stratigraphic analysis within the Granny Creek oil field of Clay and Roane countries.« less

Foraminiferal, lithic, and isotopic changes across four major unconformities at Deep Sea Drilling Project Site 548, Goban Spur: Chapter 14 in Initial reports of the Deep Sea Drilling Project

USGS Publications Warehouse

Poag, C. Wylie; Reynolds, Leslie A.; Mazzullo, James M.; Keigwin, Loyd D.

1985-01-01

Sediment samples taken at close intervals across four major unconformities (middle Miocene/upper Miocene, lower Oligocene/upper Oligocene, lower Eocene/upper Eocene, lower Paleocene/upper Paleocene) at DSDP-IPOD Site 548, Goban Spur, reveal that coeval biostratigraphic gaps, sediment discontinuities, and seismic unconformities coincide with postulated low stands of sea level. Foraminiferal, lithic, and isotopic analyses demonstrate that environments began to shift prior to periods of marine erosion, and that sedimentation resumed in the form of turbidites derived from nearby upper-slope sources. The unconformities appear to have developed where a water-mass boundary intersected the continental slope, rhythmically crossing the drill site in concert with sea-level rise and fall.

Geochemical Models of Water-Quality Changes During Aquifer Storage Recovery (ASR) Cycle Tests, Phase 1: Geochemical Models Using Existing Data

DTIC Science & Technology

2006-09-01

Richardson, in review). Figure 1 shows the lithostratigraphic setting for Eocene through Miocene strata, and the occurrence of hydrostratigraphic units of...basal Haw- thorn unit lies unconformably on lithologies informally called “ Eocene limestones,” which consist of Suwannee Limestone, Ocala Limestone

Morphological development of the Florida Escarpment: Observations on the generation of time transgressive unconformities in carbonate terrains

USGS Publications Warehouse

Paull, C.K.; Twichell, D.C.; Spiess, Fred N.; Curray, Joseph R.

1991-01-01

An unconformity of 100 m.yr magnitude continues to form on the western edge of the Florida-Bahama Platform, near 26??N, where distal Mississippi Fan sediments are progressively burying the Florida Escarpment. Multiple perspectives of the developing unconformity's morphology are revealed using available technologies including GLORIA images of the entire platform's edge, Seabeam bathymetric contours, and Deep-Tow's high resolution side-scan data calibrated with bottom photographs. The structure and stratigraphy of the buried escarpment and the associated unconformity are resolved by airgun, sparker, and Deep-Tow's 4 kHz seismic reflection data; we summarize the morphological data on the exposed part of the unconformity and the sedimentary deposits accumulating in the basin above the unconformity. The exposed cliff face is composed of a staircase of bedding-plane terraces which are developed along joint planes. The terraces extend 100-1000 m along the escarpment's face, and the intervening vertical walls are up to 100 m high. The jointed morphology of this Mesozoic limestone cliff apparently reflects erosional exposure of its interior anatomy rather than its accretionary shape. The change in slope between the platform face and the abyssal plain is very abrupt. In places along the contact between the escarpment and fan sediments, reduced chemical-charged brine seeps occur, which locally cause carbonate dissolution and precipitation, sulfide mineralization, and the deposition of a fossiliferous and organic carbon-rich lens associated with chemosynthetic communities. These seep deposits and escarpment-derived megabreccias intercalate with basinal sediments that overlie the unconformity. Because surface seismic reflection data do not produce images of the escarpment's face that closely reflect the exposed escarpment's morphology, they must also be of limited value in characterizing the surface of similar steeply dipping buried escarpments. Thus, the downslope extent of the heavily eroded platform edge is unclear. 

Rift-drift transition in the Dangerous Grounds, South China Sea

NASA Astrophysics Data System (ADS)

Peng, Xi; Shen, Chuanbo; Mei, Lianfu; Zhao, Zhigang; Xie, Xiaojun

2018-04-01

The South China Sea (SCS) has a long record of rifting before and after subsequent seafloor spreading, affecting the wide continent of the Dangerous Grounds, and its scissor-shape opening manner results in the rifting structures that vary along this margin. Some 2000 km of regional multichannel seismic data combined with borehole and dredge data are interpreted to analyze the multistage rifting process, structural architecture and dynamic evolution across the entire Dangerous Grounds. Key sequence boundaries above the Cenozoic basement are identified and classified into the breakup unconformity and the rift end unconformity, which consist of the rift-related unconformities. Reflector T70 in the east of the Dangerous Grounds represents the breakup unconformity, which is likely corresponding to the spreading of the East Subbasin. T60 formed on the top of carbonate platform is time equivalent to the spreading of the Southwest Subbasin, marking the breakup unconformity of the central Dangerous Grounds. The termination of the spreading of the SCS is manifested by the rift end unconformity of T50 in the southwest and the final rift occurring in the northwest of the Dangerous Grounds is postponed to the rift end unconformity of T40. On the basis of the stratigraphic and structural analysis, distinct segments in the structural architecture of the syn-rift units and the ages of rift-drift transition show obvious change from the proximal zone to the distal zone. Three domains, which are the Reed Bank-Palawan Rift domain, the Dangerous Grounds Central Detachment domain and Nam Con Son Exhumation domain, reflect the propagation of the margin rifting developed initially by grabens formed by high angle faults, then large half-grabens controlled by listric faults and detachments and finally rotated fault blocks in the hyper-extended upper crust associated with missing lower crust or exhumed mantle revealing a migration and stepwise rifting process in the south margin of the SCS.

The Middle Ordovician Knox unconformity in the Black Warrior Basin

USGS Publications Warehouse

Dwyer, Gary S.; Repetski, John E.

2012-01-01

Based on conodont biostratigraphy from four cores and from a previous study on cuttings from a nearby well, the unconformity is middle Whiterockian in age and likely spans most or all of the Histiodella holodentata Biozone.

Uranium Hydride Nucleation and Growth Model FY'16 ESC Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, Mary Ann; Richards, Andrew Walter; Holby, Edward F.

2016-12-20

Uranium hydride corrosion is of great interest to the nuclear industry. Uranium reacts with water and/or hydrogen to form uranium hydride which adversely affects material performance. Hydride nucleation is influenced by thermal history, mechanical defects, oxide thickness, and chemical defects. Information has been gathered from past hydride experiments to formulate a uranium hydride model to be used in a Canned Subassembly (CSA) lifetime prediction model. This multi-scale computer modeling effort started in FY’13, and the fourth generation model is now complete. Additional high-resolution experiments will be run to further test the model.

Is the Cameron River greenstone belt allochthonous?

NASA Technical Reports Server (NTRS)

Kusky, T. M.

1986-01-01

Many tectonic models for the Slave Province, N.W.T., Canada, and for Archean granite - greenstone terranes in general, are implicitly dependent on the assumption that greenstone belt lithologies rest unconformably upon older gneissic basement. Other models require originally large separations between gneissic terranes and greenstone belts. A key question relating to the tectonics of greenstone belts is therefore the original spatial relationship between the volcanic assemblages and presumed-basement gneisses, and how this relationship has been modified by subsequent deformation. What remains unclear in these examples is the significance of the so-called later faulting of the greenstone - gneiss contacts. Where unconformities between gneisses and overlying sediments are indisputable, such as at Point Lake, the significance of faults which occur below the base of the volcanic succession also needs to be evaluated. As part of an on-going investigation aimed at answering these and other questions, the extremely well-exposed Cameron River Greenstone Belt and the Sleepy Dragon Metamorphic Complex in the vicinity of Webb Lake and Sleepy Dragon Lake was mapped.

Using Pb isotopes in surface media to distinguish anthropogenic sources from undercover uranium sources

NASA Astrophysics Data System (ADS)

Kyser, Kurt; Lahusen, Larry; Drever, Garth; Dunn, Colin; Leduc, Evelyne; Chipley, Don

2015-09-01

The response in elemental concentrations and Pb isotopes in various surface media from the Cigar West unconformity-type uranium deposit located at a depth of 450 m were measured to ascertain if element migration from the deposit can be detected at the surface. The media included clay-size fractions separated from the A2, B and C soil horizons, and tree cores and twigs from black spruce (Picea mariana) and jack pine (Pinus banksiana) trees. Lead isotopes were used to trace any effect on the surface media from the deposit at depth because the 207Pb/206Pb ratios in the ore are < 0.1, whereas the background values in the basin are > 0.7 and modern anthropogenic Pb from aerosols are near 0.9. The tree cores record their lowest and therefore most radiogenic 207Pb/206Pb ratios of < 0.7 near the surface projection of the deposit and associated structures, particularly in tree rings that predate any exploration and drilling activity in the area. The median 207Pb/206Pb ratios increase in the order C, B soil horizon clays, tree cores, A2 soil clays and twigs because of the increasing contribution of common Pb with high ratios from anthropogenic sources that affect the shallowest media the most. Although this anthropogenic Pb as well as that from the background dominates the composition of all media at the surface and the contribution from the deposit at depth is diminished toward the surface, ore-related Pb is still present as a few percent of the composition of pathfinder elements and Pb isotopes.

Nature and significance of Austin-Taylor unconformity on western margin of east Texas basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Surles, M.A. Jr.

1984-04-01

The Taylor Marl unconformably overlies the Austin Chalk on the western margin of the East Texas basin. Along this contact, up to 275 ft (84 m) of upper Austin is missing in the Waco area and up to 450 ft (137 m) in Bell County. However, the Austin Chalk appears to have been more-or-less uniformly deposited throughout the study area. Apparently regional uplift caused a regression that terminated Austin deposition and was related to the erosion of the upper Chalk. While the unconformity is areally extensive, slightly angular, and accounts for a relatively long period of time, the mechanism ofmore » erosion that caused the unconformity is still uncertain. Erosion was terminated by the deposition of the lower Taylor Marl. Taylor A, the lowermost subdivision of the lower Taylor, was deposited in a near-shore environment that was highly variable. Of particular interest is the relationship of this unconformity to structure and probably to oil occurrence in the Austin Chalk in McLennan and Falls Counties. Major Austin fracturing, which apparently does not extend into the Taylor in Falls County, clearly indicates that structure in the Chalk, at least in part, antedates Taylor deposition. Oil occurrence in the Chalk is clearly related to fracturing and probably is localized by post-Austin-pre-Taylor fracture systems.« less

The Middle Jurassic Entrada Sandstone near Gallup, New Mexico

USGS Publications Warehouse

Robertson, J.F.; O'Sullivan, R. B.

2001-01-01

Near Gallup, New Mexico, the Middle Jurassic Entrada Sandstone consists of, in ascending order, the Iyanbito Member, the Rehoboth Member, and an upper sandstone member. The Rehoboth Member is named herein to replace the middle siltstone member, with a type section located 26 km east of Gallup. The Iyanbito Member has been erroneously equated with the Wingate Sandstone of northeast Arizona, and the Rehoboth Member has been miscorrelated with the Dewey Bridge Member of the Entrada in Utah. The Dewey Bridge is an older unit that does not extend into New Mexico. The Iyanbito Member, east of Gallup, overlies the J-2 unconformity and the eroded tops of the Owl Rock and Petrified Forest Members of the Chinle Formation. The Wingate Sandstone of the Lower Jurassic Glen Canyon Group overlies the J-0 unconformity and the underlying Rock Point Member (topmost unit) of the Chinle Formation in northeast Arizona. Both the Wingate Sandstone and the Rock Point Member are missing east of Gallup below the J-2 unconformity. Similarly, the Wingate is missing southwest of Gallup, near Lupton, Arizona, but the Rock Point Member is present and underlies the Iyanbito from Zuni northward to Toadlena, New Mexico. The Wingate and other formations of the Glen Canyon Group thin and wedge out southward and eastward in northeast Arizona. The J-2 unconformity truncates the Wingate Sandstone and the underlying J-0 unconformity, 5 km north of Toadlena.

Development of a mathematical model for the dissolution of uranium dioxide. II. Statistical model for the dissolution of uranium dioxide tablets in nitric acid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhukovskii, Yu.M.; Luksha, O.P.; Nenarokomov, E.A.

1988-03-01

We have derived a statistical model for the dissolution of uranium dioxide tablets for the 6 to 12 M concentration range and temperatures from 80/sup 0/C to the boiling point. The model differs qualitatively from the dissolution model for ground uranium dioxide. In the indicated range of experimental conditions, the mean-square deviation of the curves for the model from the experimental curves is not greater than 6%.

Reactive transport modeling at uranium in situ recovery sites: uncertainties in uranium sorption on iron hydroxides

USGS Publications Warehouse

Johnson, Raymond H.; Tutu, Hlanganani; Brown, Adrian; Figueroa, Linda; Wolkersdorfer, Christian

2013-01-01

Geochemical changes that can occur down gradient from uranium in situ recovery (ISR) sites are important for various stakeholders to understand when evaluating potential effects on surrounding groundwater quality. If down gradient solid-phase material consists of sandstone with iron hydroxide coatings (no pyrite or organic carbon), sorption of uranium on iron hydroxides can control uranium mobility. Using one-dimensional reactive transport models with PHREEQC, two different geochemical databases, and various geochemical parameters, the uncertainties in uranium sorption on iron hydroxides are evaluated, because these oxidized zones create a greater risk for future uranium transport than fully reduced zones where uranium generally precipitates.

Laboratory column experiments and transport modeling to evaluate retardation of uranium in an aquifer downgradient of a uranium in-situ recovery site

DOE PAGES

Dangelmayr, Martin A.; Reimus, Paul W.; Wasserman, Naomi L.; ...

2017-05-01

The purpose of this study was to determine the attenuation potential and retardation of uranium in sediments taken from boreholes at the Smith-Ranch Highland in-situ recovery (ISR) site. Five column experiments with four different sediments were conducted to study the effects of variable mineralogy and alkalinity on uranium breakthrough. Uranium transport was modeled with PHREEQC using a generalized composite surface complexation model (GC SCM) with one, two, and, three generic surfaces, respectively. Reactive surface areas were approximated with PEST using BET derived surface areas to constrain fitting parameters. Uranium breakthrough was delayed by a factor of 1.68, 1.69 and 1.47more » relative to the non-reactive tracer for three of the 5 experiments at an alkalinity of 540 mg/l. A sediment containing smectite and kaolinite retained uranium by a factor of 2.80 despite a lower measured BET surface area. Decreasing alkalinity to 360 mg/l from 540 mg/l increased retardation by a factor of 4.26. Model fits correlated well to overall BET surface area in the three columns where clay content was less than 1%. For the sediment with clay, models consistently understated uranium retardation when reactive surface sites were restricted by BET results. Calcite saturation was shown to be a controlling factor for uranium desorption as the pH of the system changes. A pH of 6 during a secondary background water flush remobilized previously sorbed uranium resulting in a secondary uranium peak at twice the influent concentrations. Furthermore, this study demonstrates the potential of GC SCM models to predict uranium transport in sediments with homogenous mineral composition, but highlights the need for further research to understand the role of sediment clay composition and calcite saturation in uranium transport.« less

Laboratory column experiments and transport modeling to evaluate retardation of uranium in an aquifer downgradient of a uranium in-situ recovery site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dangelmayr, Martin A.; Reimus, Paul W.; Wasserman, Naomi L.

The purpose of this study was to determine the attenuation potential and retardation of uranium in sediments taken from boreholes at the Smith-Ranch Highland in-situ recovery (ISR) site. Five column experiments with four different sediments were conducted to study the effects of variable mineralogy and alkalinity on uranium breakthrough. Uranium transport was modeled with PHREEQC using a generalized composite surface complexation model (GC SCM) with one, two, and, three generic surfaces, respectively. Reactive surface areas were approximated with PEST using BET derived surface areas to constrain fitting parameters. Uranium breakthrough was delayed by a factor of 1.68, 1.69 and 1.47more » relative to the non-reactive tracer for three of the 5 experiments at an alkalinity of 540 mg/l. A sediment containing smectite and kaolinite retained uranium by a factor of 2.80 despite a lower measured BET surface area. Decreasing alkalinity to 360 mg/l from 540 mg/l increased retardation by a factor of 4.26. Model fits correlated well to overall BET surface area in the three columns where clay content was less than 1%. For the sediment with clay, models consistently understated uranium retardation when reactive surface sites were restricted by BET results. Calcite saturation was shown to be a controlling factor for uranium desorption as the pH of the system changes. A pH of 6 during a secondary background water flush remobilized previously sorbed uranium resulting in a secondary uranium peak at twice the influent concentrations. Furthermore, this study demonstrates the potential of GC SCM models to predict uranium transport in sediments with homogenous mineral composition, but highlights the need for further research to understand the role of sediment clay composition and calcite saturation in uranium transport.« less

A compartmental model of uranium in human hair for protracted ingestion of natural uranium in drinking water.

PubMed

Li, W B; Karpas, Z; Salonen, L; Kurttio, P; Muikku, M; Wahl, W; Höllriegl, V; Hoeschen, C; Oeh, U

2009-06-01

To predict uranium in human hair due to chronic exposure through drinking water, a compartment representing human hair was added into the uranium biokinetic model developed by the International Commission on Radiological Protection (ICRP). The hair compartmental model was used to predict uranium excretion in human hair as a bioassay indicator due to elevated uranium intakes. Two excretion pathways, one starting from the compartment of plasma and the other from the compartment of intermediate turnover soft tissue, are assumed to transfer uranium to the compartment of hair. The transfer rate was determined from reported uranium contents in urine and in hair, taking into account the hair growth rate of 0.1 g d(-1). The fractional absorption in the gastrointestinal tract of 0.6% was found to fit best to describe the measured uranium levels among the users of drilled wells in Finland. The ingestion dose coefficient for (238)U, which includes its progeny of (234)Th, (234m)Pa, and (234)Pa, was calculated equal to 1.3 x 10(-8) Sv Bq(-1) according to the hair compartmental model. This estimate is smaller than the value of 4.5 x 10(-8) Sv Bq(-1) published by ICRP for the members of the public. In this new model, excretion of uranium through urine is better represented when excretion to the hair compartment is accounted for and hair analysis can provide a means for assessing the internal body burden of uranium. The model is applicable for chronic exposure as well as for an acute exposure incident. In the latter case, the hair sample can be collected and analyzed even several days after the incident, whereas urinalysis requires sample collection shortly after the exposure. The model developed in this study applies to ingestion intakes of uranium.

Amidoxime Polymers for Uranium Adsorption: Influence of Comonomers and Temperature

PubMed Central

Wiechert, Alexander I.; Das, Sadananda; Yiacoumi, Sotira

2017-01-01

Recovering uranium from seawater has been the subject of many studies for decades, and has recently seen significant progress in materials development since the U.S. Department of Energy (DOE) has become involved. With DOE direction, the uranium uptake for amidoxime-based polymer adsorbents has more than tripled in capacity. In an effort to better understand how these new adsorbent materials behave under different environmental stimuli, several experimental and modeling based studies have been employed to investigate impacts of competing ions, salinity, pH, and other factors on uranium uptake. For this study, the effect of temperature and type of comonomer on uranium adsorption by three different amidoxime adsorbents (AF1, 38H, AI8) was examined. Experimental measurements of uranium uptake were taken in 1−L batch reactors from 10 to 40 °C. A chemisorption model was developed and applied in order to estimate unknown system parameters through optimization. Experimental results demonstrated that the overall uranium chemisorption process for all three materials is endothermic, which was also mirrored in the model results. Model simulations show very good agreement with the data and were able to predict the temperature effect on uranium adsorption as experimental conditions changed. This model may be used for predicting uranium uptake by other amidoxime materials. PMID:29113060

Sensitivity of geological, geochemical and hydrologic parameters in complex reactive transport systems for in-situ uranium bioremediation

NASA Astrophysics Data System (ADS)

Yang, G.; Maher, K.; Caers, J.

2015-12-01

Groundwater contamination associated with remediated uranium mill tailings is a challenging environmental problem, particularly within the Colorado River Basin. To examine the effectiveness of in-situ bioremediation of U(VI), acetate injection has been proposed and tested at the Rifle pilot site. There have been several geologic modeling and simulated contaminant transport investigations, to evaluate the potential outcomes of the process and identify crucial factors for successful uranium reduction. Ultimately, findings from these studies would contribute to accurate predictions of the efficacy of uranium reduction. However, all these previous studies have considered limited model complexities, either because of the concern that data is too sparse to resolve such complex systems or because some parameters are assumed to be less important. Such simplified initial modeling, however, limits the predictive power of the model. Moreover, previous studies have not yet focused on spatial heterogeneity of various modeling components and its impact on the spatial distribution of the immobilized uranium (U(IV)). In this study, we study the impact of uncertainty on 21 parameters on model responses by means of recently developed distance-based global sensitivity analysis (DGSA), to study the main effects and interactions of parameters of various types. The 21 parameters include, for example, spatial variability of initial uranium concentration, mean hydraulic conductivity, and variogram structures of hydraulic conductivity. DGSA allows for studying multi-variate model responses based on spatial and non-spatial model parameters. When calculating the distances between model responses, in addition to the overall uranium reduction efficacy, we also considered the spatial profiles of the immobilized uranium concentration as target response. Results show that the mean hydraulic conductivity and the mineral reaction rate are the two most sensitive parameters with regard to the overall uranium reduction. But in terms of spatial distribution of immobilized uranium, initial conditions of uranium concentration and spatial uncertainty in hydraulic conductivity also become important. These analyses serve as the first step of further prediction practices of the complex uranium transport and reaction systems.

In situ stress conditions at IODP Site C0002 reflecting the tectonic evolution of the sedimentary system near the seaward edge of the Kumano basin, offshore from SW Japan

NASA Astrophysics Data System (ADS)

Song, Insun; Chang, Chandong

2017-05-01

This paper presents a complete set of in situ stress calculations for depths of 200-1400 meters below seafloor at Integrated Ocean Drilling Program (IODP) Site C0002, near the seaward margin of the Kumano fore-arc basin, offshore from southwest Japan. The vertical stress component was obtained by integrating bulk density calculations from moisture and density logging data, and the two horizontal components were stochastically optimized by minimizing misfits between a probabilistic model and measured breakout widths for every 30 m vertical segment of the wellbore. Our stochastic optimization process reveals that the in situ stress regime is decoupled across an unconformity between an accretionary complex and the overlying Kumano fore-arc basin. The stress condition above the unconformity is close to the critical condition for normal faulting, while below the unconformity the geologic system is stable in a normal to strike-slip fault stress regime. The critical state of stress demonstrates that the tectonic evolution of the sedimentary system has been achieved mainly by the regionally continuous action of a major out-of-sequence thrust fault during sedimentation in the fore-arc basin. The stable stress condition in the accretionary prism is interpreted to have resulted from mechanical decoupling by the accommodation of large displacement along the megasplay fault.

Nature and regional significance of unconformities associated with the Middle Ordovician Hagan K-bentonite complex in the North American midcontinent

USGS Publications Warehouse

Kolata, Dennis R.; Huff, W.D.; Bergstrom, Stig M.

1998-01-01

Stratal patterns of the Middle Ordovician Hagan K-bentonite complex and associated rocks show that the Black River-Trenton unconformity in the North American midcontinent formed through the complex interplay of eustasy, sediment accumulation rates, siliciclastic influx, bathymetry, seawater chemistry, and perhaps local tectonic uplift. The unconformity is diachronous and is an amalgamated surface that resulted from local late Turinian lowstand exposure followed by regional early Chatfieldian transgressive drowning and sediment starvation. The duration of the unconformity is greatest in southern Wisconsin, northern Illinois, and northern Indiana, where the Deicke and Millbrig K-bentonite Beds converge at the unconformity. On the basis of published isotopic ages for the Deicke and Millbrig beds, it is possible that in these regions erosion and non-deposition spanned a period of as much as 3.2 m.y. Two broad coeval depositional settings are recognized within the North American midcontinent during early Chatfieldian time. 1) An inner shelf, subtidal facies of fossiliferous shale (Spechts Ferry Shale Member and Ion Shale Member of the Decorah Formation) and argillaceous lime mudstone and skeletal wackestone (Guttenberg and Kings Lake Limestone Members) extended from the Canadian shield and Transcontinental arch southeastward through Minnesota, Wisconsin, Iowa, and Missouri. 2) A seaward, relatively deep subtidal, sediment-starved, middle shelf extended eastward from the Mississippi Valley region to the Taconian foreland basins in the central and southern Appalachians and southward through the pericratonic Arkoma and Black Warrior basins. In the inner shelf region, the Black River-Trenton unconformity is a composite of at least two prominent hardground omission surfaces, one at the top of the Castlewood and Carimona Limestone Members and the other at the top of the Guttenberg and Kings Lake Limestone Members, both merging to a single surface in the middle shelf region. The inner and middle shelves redeveloped later in approximately the same regions during Devonian and Mississippian time.

Development of a Kelp-type Structure Module in a Coastal Ocean Model to Assess the Hydrodynamic Impact of Seawater Uranium Extraction Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Taiping; Khangaonkar, Tarang; Long, Wen

2014-02-07

In recent years, with the rapid growth of global energy demand, the interest in extracting uranium from seawater for nuclear energy has been renewed. While extracting seawater uranium is not yet commercially viable, it serves as a “backstop” to the conventional uranium resources and provides an essentially unlimited supply of uranium resource. With recent advances in seawater uranium extraction technology, extracting uranium from seawater could be economically feasible when the extraction devices are deployed at a large scale (e.g., several hundred km2). There is concern however that the large scale deployment of adsorbent farms could result in potential impacts tomore » the hydrodynamic flow field in an oceanic setting. In this study, a kelp-type structure module was incorporated into a coastal ocean model to simulate the blockage effect of uranium extraction devices on the flow field. The module was quantitatively validated against laboratory flume experiments for both velocity and turbulence profiles. The model-data comparison showed an overall good agreement and validated the approach of applying the model to assess the potential hydrodynamic impact of uranium extraction devices or other underwater structures in coastal oceans.« less

Quartz-pebble-conglomerate gold deposits: Chapter P in Mineral deposit models for resource assessment

USGS Publications Warehouse

Taylor, Ryan D.; Anderson, Eric D.

2018-05-17

Quartz-pebble-conglomerate gold deposits represent the largest repository of gold on Earth, largely due to the deposits of the Witwatersrand Basin, which account for nearly 40 percent of the total gold produced throughout Earth’s history. This deposit type has had a controversial history in regards to genetic models. However, most researchers conclude that they are paleoplacer deposits that have been modified by metamorphism and hydrothermal fluid flow subsequent to initial sedimentation.The deposits are found exclusively within fault-bounded depositional basins. The periphery of these basins commonly consists of granite-greenstone terranes, classic hosts for lode gold that source the detrital material infilling the basin. The gold reefs are typically located along unconformities or, less commonly, at the top of sedimentary beds. Large quartz pebbles and heavy-mineral concentrates are found associated with the gold. Deposits that formed prior to the Great Oxidation Event (circa 2.4 giga-annum [Ga]) contain pyrite, whereas younger deposits contain iron oxides. Uranium minerals and hydrocarbons are also notable features of some deposits.Much of the gold in these types of deposits forms crystalline features that are the product of local remobilization. However, some gold grains preserve textures that are undoubtedly of detrital origin. Other heavy minerals, such as pyrite, contain growth banding that is truncated along broken margins, which indicates that they were transported into place as opposed to forming by in situ growth in a hydrothermal setting.The ore tailings associated with these deposits commonly contain uranium-rich minerals and sulfides. Oxidation of the sulfides releases sulfuric acid and mobilizes various metals into the environment. The neutralizing potential of the tailings is minimal, since carbonate minerals are rare. The continuity of the tabular ore bodies, such as those of the Witwatersrand Basin, has allowed these mines to be the deepest in the world. The extreme depths create engineering complications and safety issues for the miners, such as rock bursts as a result of pressure release.The richness of these deposits makes them a desirable exploration target. However, the likelihood of future discoveries is minimal. Small deposits found in the United States include those found at Nemo in the Black Hills of South Dakota and Deep Lake in the Sierra Madre of Wyoming.

Seismic stratigraphy of sedimentary cover in the southern Amerasia Basin between 140E and 170W

NASA Astrophysics Data System (ADS)

Poselov, V.; Butsenko, V.; Kaminskiy, V.; Kireev, A.; Grikurov, G.

2013-12-01

Seismic reflection data (MCS) acquired by Russian expeditions in 2007, 2009, 2011 and 2012 are correlated with earlier Polarstern (AWI-91090) and US (78AR_808) lines calibrated by drilling on the Lomonosov Ridge (LR) and in the Chukchi Sea (ACEX hole and POPCORN well, respectively). In the absence of direct intersections between those and Russian lines, the correlation is based on analysis of wave fields. Main seismic horizons and their intervening units are traced throughout the entire study area. The uppermost unconformity in both holes is related to pre-Miocene depositional hiatus at the base of essentially hemipelagic unit. Specific wave characteristics of both the unconformity and overlying sediments are persistently recorded on seismic lines. Hemipelagic drape is typically relatively thin (few hundred meters) but may thicken to ~1,500-2,000 m in some deepwater basins. Another major depositional hiatus spanning ~20 Ma is interpreted in the ACEX hole between the lowermost drilled Campanian and Upper Paleocene units. On seismic records it is recognized as post-Campanian unconformity (pCU) traced along the length of the near-Siberia segment of LR and in deep shelf/margin sedimentary basins of the East Siberian and western Chukchi Seas. Farther east pCU correlates with Mid-Brookian unconformity (MBU) separating the Lower and Upper Brookian terrigenous sequences. In Popcorn well the Upper Brookian is about 1,300 m thick; on the Russian margin a comparable thickness of equivalent Upper Paleocene-Eocene units sandwiched between pCU and pre-Miocene unconformity is observed only in structural lows. Older cover units on the Russian East Arctic margin are not sampled by drilling. Among them only one displays particular wave field features clearly comparable to those observed in the carbonate-dominated Carboniferous-Permian Lisburne Group (LG) of the US Chukchi Sea. This marker sequence is confidently recognized on seismic sections in the North Chukchi Trough (NCT) and the Vilkitsky Basin as relatively thick (1,500-3,000 m) unit whose much thinner (~300 m) continuation can also be traced over the southern Mendeleev Rise. A thick (~5000 m) well stratified sedimentary pile mapped in NCT between LG-type unit and the acoustic basement is likely to represent a counterpart of the D3-C1 base of the Lower Ellesmerian Sequence. Like in the US Chukchi Sea, the latter is also truncated here by Permian(?) unconformity and buried under 5,000-7,000 m of inferred Late Permian to Early Cretaceous strata probably corresponding to Upper Ellesmerian, 'Rift' and Lower Brookian Sequences and separated by respective (presumably Jurassic and Early Cretaceous) unconformities. The thickness of pre-Cenozoic units in NCT and the relief of intervening unconformities are highly variable suggesting syndepositional rifting.

Geologic map of the Pinedale quadrangle, McKinley County, New Mexico

USGS Publications Warehouse

Robertson, Jacques F.

2005-01-01

The 1:24,000-scale geologic map of the Pinedale 7.5' quadrangle lies in the western part of the Grants uranium mineral belt, which was mapped and studied under a cooperative agreement between the USGS and the U.S. Department of Energy. A spectacular panoramic view of the southern half of the Pinedale quadrangle is obtained looking northward from Interstate Highway 40, particularly from the New Mexico State travelers' rest stop near the Shell Oil Company's Ciniza Refinery, 28.5 kilometers (17.8 miles) east of Gallup. A west-trending escarpment, 200 meters high, of massive red sandstone, rises above a broad valley, its continuity broken only by a few deep and picturesque canyons in the western half of the quadrangle. The escarpment is formed by the eolian Entrada Sandstone of Late Jurassic age. The Entrada unconformably overlies the Chinle Formation of Late Triassic age, which occupies the valley below. The Chinle Formation consists of cherty mottled limestone and mudstone of the Owl Rock Member and underlying, poorly consolidated, red to purple fluvial siltstone, mudstone, and sandstone beds of the Petrified Forest Member. The pinyon- and juniper-covered bench that tops the escarpment is underlain by the Todilto Limestone. A quarry operation, located just north of the Indian community of Iyanbito in the southwestern part of the quadrangle, produces crushed limestone aggregate for highway construction and railroad ballast. Beyond the escarpment to the north and rising prominently above it, is the northwest-trending Fallen Timber Ridge. Near the west side of the quadrangle lie the peaks of Midget Mesa, and Mesa Butte, the latter of which has the highest altitude in the area at 2,635 meters (8,030 feet) above sea level. The prominences are capped by buff-colored resistant beds of the Dakota Sandstone of Late Cretaceous age, containing some interbedded coal. These beds unconformably overlie the uranium-bearing Morrison Formation, which consists of red, green, and gray shale, orange feldspathic sandstone, and green tuffaceous mudstone, deposited in ancient lakes, alluvial fans, and rivers during the Upper Jurassic Period. Thick, crossbedded, white beds of the Cow Springs Sandstone, derived from ancient windblown desert sands, underlie the Morrison. In the northern part of the quadrangle, the Dakota Sandstone is overlain by gray Mancos Shale and yellowish-gray Two Wells and Gallup Sandstones that were deposited in Late Cretaceous seas. Unconsolidated deposits of Quaternary age are found throughout the quadrangle in talus, slope wash, fans, valley alluviums, pediments, and as windblown sands in dunes and blanket deposits. The strata conform to the regional dip of about three degrees to north, except where they are down-folded some 200 meters along the Pinedale monocline, whose limbs follow a sinuous west-northwest trend across the northern half of the quadrangle. The monocline is beautifully exposed at Pinedale, where it shows as much as 20 degrees dip on the pine-studded bare rock slope of the Two Wells Sandstone. A north-plunging broad anticline and accompanying syncline is developed in the east-central part of the quadrangle but dies out against the monocline. A minor fault, with barely 3 meters of vertical displacement, extends several kilometers westward across the Todilto Limestone bench. A large landslide mass, 1.5 kilometers long by 0.7 kilometers wide occurs in the Mancos Shale west of Pinedale. Exploration drilling for uranium in the Morrison Formation has been extensive in the quadrangle, particularly north of the monocline, which adjoins the Old Church Rock mine area, west northwest of the quadrangle.

Seismic Stratigraphic Evidence From SE Ross Sea for Late Oligocene Glaciers and ice Streams Issuing From Marie Byrd Land

NASA Astrophysics Data System (ADS)

Sorlien, C. C.; Luyendyk, B. P.; Wilson, D. S.; Decesari, R. C.; Bartek, L. R.; Diebold, J. B.

2006-12-01

The extent of the West Antarctic ice sheet during mid-Cenozoic time is controversial and important to climate models. High-resolution multichannel seismic reflection data were acquired using the RVIB Palmer along the edge of the Ross Ice Shelf across the Eastern Basin of Ross Sea, in an area where calving of the ice shelf has exposed seafloor that has not been accessible to marine geophysics in several decades. A sub-basin in the far southeast corner of Ross Sea contains a succession of sediment-filled troughs, each capped by an unconformity. These troughs range between 2 and 20 km across, are 100 to 150 m-deep, with the narrower ones bounded by flat-topped ridges interpreted as moraines. We interpret the troughs interval to slightly predate 25 Ma. Reflections just 100 m below the troughs interval can be directly correlated to near DSDP270 where they underlie strata dated at ~25 Ma. A deeper stack of prograding sequences associated with a flat- topped ridge are interpreted as pre-25 Ma, possibly early Oligocene, deltas formed adjacent to the grounding line of a glacier, and the flat-topped ridge to be a moraine. The shallowest of the stack of unconformities capping the broad troughs can be projected across a basement ridge on trend with Roosevelt Island to a regional angular unconformity ("Red"), present across 70 km to deep sedimentary Eastern Basin. This unconformity represents about 1 km of missing stratigraphic section, is smooth and level, and splits into several major sequence boundaries within deep Eastern Basin. The second shallowest of these boundaries is dated about 14 Ma at DSDP-270. We interpret this unconformity to be cut by regional thick, grounded ice at depths several hundred meters below sea level. Pre-25 Ma strata show evidence of narrow erosional troughs and reflective mounds or ridges on the west flank of the basement ridge, but such features are not present in southern deep Eastern Basin near the ice shelf edge. This is evidence that the troughs were carved by glaciers issuing from distant highlands of Marie Byrd Land and not from East Antarctica. Late Oligocene through mid Miocene and younger prograding and unconformities farther north in Eastern Basin indicate grounded ice there. One possible interpretation is that "Red" was cut by thick, grounded ice that affected all of the Eastern Ross Sea paleo-shelf, while the pre-25 Ma glaciers affected only the area proximal to Marie Byrd Land. Late Oligocene glaciation on the outer shelf above deep Eastern Basin may have been sourced from East Antarctica and/or Central High. Evidence for pre-25 Ma glaciation proximal to Marie Byrd Land, combined with evidence for Oligocene ice caps at widely-separated localities of West Antarctica, allow the interpretation that portions of the West Antarctic Ice Sheet developed during Oligocene time. The broad troughs and the stack of prograding sequences may be related to dynamic ice caps and sea level falls in mid Oligocene and earliest Oligocene time. The Middle Miocene Red unconformity may be related to development of polar (cold-base) ice sheets. Oligocene glaciation implies that Marie Byrd Land and eastern Ross Sea have subsided from higher elevation due to cooling after late Cretaceous crustal thinning.

Controlling intake of uranium in the workplace: Applications of biokinetic modeling and occupational monitoring data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leggett, Richard Wayne; Eckerman, Keith F; McGinn, Wilson

2012-01-01

This report provides methods for interpreting and applying occupational uranium monitoring data. The methods are based on current international radiation protection guidance, current information on the chemical toxicity of uranium, and best available biokinetic models for uranium. Emphasis is on air monitoring data and three types of bioassay data: the concentration of uranium in urine; the concentration of uranium in feces; and the externally measured content of uranium in the chest. Primary Reference guidance levels for prevention of chemical effects and limitation of radiation effects are selected based on a review of current scientific data and regulatory principles for settingmore » standards. Generic investigation levels and immediate action levels are then defined in terms of these primary guidance levels. The generic investigation and immediate actions levels are stated in terms of radiation dose and concentration of uranium in the kidneys. These are not directly measurable quantities, but models can be used to relate the generic levels to the concentration of uranium in air, urine, or feces, or the total uranium activity in the chest. Default investigation and immediate action levels for uranium in air, urine, feces, and chest are recommended for situations in which there is little information on the form of uranium taken into the body. Methods are prescribed also for deriving case-specific investigation and immediate action levels for uranium in air, urine, feces, and chest when there is sufficient information on the form of uranium to narrow the range of predictions of accumulation of uranium in the main target organs for uranium: kidneys for chemical effects and lungs for radiological effects. In addition, methods for using the information herein for alternative guidance levels, different from the ones selected for this report, are described.« less

Tectonic controls on deposition of Middle Jurassic strata in a retroarc foreland basin, Utah-Idaho trough, western interior, United States

NASA Astrophysics Data System (ADS)

Bjerrum, Christian J.; Dorsey, Rebecca J.

1995-08-01

An electronic supplement of this material may be obtained on a diskette or Anonymous FTP from KOSMOS.AGU.ORG. (LOGIN to AGU's FTP account using ANONYMOUS as the username and GUEST as the password. Go to the right directory by typing CD APEND. Type LS to see what files are available. Type GET and the name of the file to get it. Finally, type EXIT to leave the system.) (Paper 95TC01448, Tectonic controls on deposition of Middle Jurassic strata in a retroarc foreland basin, Utah-Idaho trough, western interior, United States, Christian J. Bjerrum and Rebecca J. Dorsey). Diskette may be ordered from American Geophysical Union, 2000 Florida Avenue, N. W., Washington, DC 20009; $15.00. Payment must accompany order. A thick succession of Jurassic nonmarine and marine sedimentary rocks is exposed in a large area from northern Arizona to eastern Idaho and western Wyoming. These sediments accumulated in the Utah-Idaho trough, a deep elongate cratonal basin whose origin has recently been debated. Detailed stratigraphic analysis, subsidence analysis, and first-order flexural modeling of these deposits (this study) provide new insights into the timing and mechanisms of subsidence in the Utah-Idaho trough. Lower and Middle Jurassic strata are divided into six unconformity-bounded sequences. In contrast to the overall uniform thickness of Lower Jurassic sequences (1 and 2), Middle Jurassic strata (sequences 3 through 6) consist of distinctly westward thickening sedimentary packages in which basal shallow marine deposits onlap eastward onto bounding unconformities. Basal strata of sequences 3 through 6 pass upward into widespread progradational continental deposits that are truncated progressively toward the east (cratonward) by the next unconformity. Decompacted total subsidence curves show that the rate of subsidence in most sections increased sharply at the end of sequence 2 time (J-2 unconformity; ˜170 Ma). This is interpreted to record the onset of Middle Jurassic deposition in the distal part of a retroarc foreland basin. The unconformities and distinctive stratal geometries may have formed in response to forebulge migration caused by episodic thrusting in the Cordilleran orogen to the west. First-order flexural modeling was carried out to test the hypothesis of flexural subsidence in the Utah-Idaho trough. Trial-and-error comparisons produce a close match between decompacted stratigraphic profiles and model deflection profiles. The best fit is obtained using an infinite elastic plate (D = 1 × 1024 Nm), a moderate load topography, elevated base level, and an overfilled basin. Using recently published tectonic reconstructions for Nevada and Utah, we find close spatial agreement between a large Middle Jurassic fold-thrust belt and the supracrustal load inferred from model simulations. Our integrated basin analysis thus supports the interpretation of some previous studies that the Middle Jurassic Utah-Idaho trough was a retroarc foreland basin that formed east of a belt of regional contractile deformation and crustal thickening in western and central Nevada and southeastern California. Late Jurassic extension and normal faulting in northeastern Nevada may have been related to gravitational collapse of overthickened crust in the Cordilleran orogen. This coincides with a period of slowed subsidence in the Utah-Idaho trough that began at about 157 Ma.

Quantitative palaeodrainage analysis in the Pleistocene of the Po Plain (Italy)

NASA Astrophysics Data System (ADS)

Vezzoli, G.; Garzanti, E.; Sciunnach, D.

2009-04-01

During the Pleistocene, Po Plain deposits recorded repeated waxing and waning of Alpine ice caps, and thus provide an excellent opportunity to investigate the interactions between pronounced climatic fluctuations and background tectonic activity (Scardia et al., 2006), resulting in frequent changes of drainage patterns. A high-resolution Pleistocene stratigraphy, with a complete sedimentological, paleontological, petrographic-mineralogical, magneto-stratigraphic, and seismic data base, was recently obtained from eleven continuous cores drilled in the Lombardy Po Plain north of the Po River (ENI and Regione Lombardia, 2002). In the present study we focus on two cores in the proximal (Cilavegna) and distal plain (Pianengo), which best exemplify the drastic change in sedimentary systems and drainage patterns associated with the onset of major Pleistocene glaciations in the Alps (˜870ky; Muttoni et al., 2003). This climatic event is recorded by a regional unconformity (named R-unconformity by Muttoni et al., 2003), traced all across the Po Basin and encountered at -81 m depth in the Pianengo Core and at -98 m depth in the Cilavegna Core. The Cilavegna Core consists of metamorphiclastic floodplain sediments, capped by the R-unconformity and overlain by quartzofeldspathic braidplain deposits. The Pianengo Core consists of metamorphiclastic deltaic to floodpain sediments, capped by the R-unconformity and overlain by alluvial-fan gravels rich in carbonate pebbles; another unconformity at -39 m depth is overlain by metamorphiclastic braidplain deposits. Our quantitative approach to paleodrainage analysis is based on comprehensive information obtained from modern settings (Garzanti et al., 2004; 2006). End-member modelling and similarity analysis allows us to objectively compare detrital modes from modern and ancient deposits, and to reconstruct the evolution of sediment pathways through geologic time (Vezzoli and Garzanti 2009). The Cilavegna Core documents stepwise south-westward shifts of major tributaries draining the axial belt. The Pianengo Core records the rapid southward progradation of transverse alluvial fans fed locally from the Southern Alps, followed by progressive establishment of the modern Adda river system. Evolving drainage patterns and river avulsions represent a major cause of compositional change in foreland-basin deposits. Lateral shifts of river courses, commonly associated with unconformities and favoured by an increase in the ratio between sediment fluxes and subsidence, provide crucial information on tectonic or climatic events, and should be given full consideration in provenance studies. ENI and Regione Lombardia. 2002. Geologia degli acquiferi padani della Regione Lombardia. Firenze, Società Elaborazioni Cartografiche s.r.l., 130 p. Muttoni G., Carcano C., Garzanti E., Ghielmi M., Piccin A., Pini R., Rogledi S., and Sciunnach D. 2003. Onset of major Pleistocene glaciations in the Alps. Geology, 31, 989-992. Scardia G., Muttoni G., and Sciunnach D. 2006. Subsurface magnetostratigraphy of Pleistocene sediments from the Po Plain (Italy): constraints on rates of sedimentation and rock uplift. Geological Society of America Bulletin, 118, 1299-1312. Vezzoli G. and Garzanti E. 2009. Tracking paleodrainage in foreland-basin sequences. Journal of Geology, In press.

First-Principles Integrated Adsorption Modeling for Selective Capture of Uranium from Seawater by Polyamidoxime Sorbent Materials

DOE PAGES

Ladshaw, Austin P.; Ivanov, Alexander S.; Das, Sadananda; ...

2018-03-27

Nuclear power is a relatively carbon-free energy source that has the capacity to be utilized today in an effort to stem the tides of global warming. The growing demand for nuclear energy, however, could put significant strain on our uranium ore resources, and the mining activities utilized to extract that ore can leave behind long-term environmental damage. A potential solution to enhance the supply of uranium fuel is to recover uranium from seawater using amidoximated adsorbent fibers. This technology has been studied for decades but is currently plagued by the material’s relatively poor selectivity of uranium over its main competitormore » vanadium. In this work, we investigate the binding schemes between uranium, vanadium, and the amidoxime functional groups on the adsorbent surface. Using quantum chemical methods, binding strengths are approximated for a set of complexation reactions between uranium and vanadium with amidoxime functionalities. Those approximations are then coupled with a comprehensive aqueous adsorption model developed in this work to simulate the adsorption of uranium and vanadium under laboratory conditions. Experimental adsorption studies with uranium and vanadium over a wide pH range are performed, and the data collected are compared against simulation results to validate the model. It was found that coupling ab initio calculations with process level adsorption modeling provides accurate predictions of the adsorption capacity and selectivity of the sorbent materials. Furthermore, this work demonstrates that this multiscale modeling paradigm could be utilized to aid in the selection of superior ligands or ligand compositions for the selective capture of metal ions. Furthermore, this first-principles integrated modeling approach opens the door to the in silico design of next-generation adsorbents with potentially superior efficiency and selectivity for uranium over vanadium in seawater.« less

First-Principles Integrated Adsorption Modeling for Selective Capture of Uranium from Seawater by Polyamidoxime Sorbent Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ladshaw, Austin P.; Ivanov, Alexander S.; Das, Sadananda

Nuclear power is a relatively carbon-free energy source that has the capacity to be utilized today in an effort to stem the tides of global warming. The growing demand for nuclear energy, however, could put significant strain on our uranium ore resources, and the mining activities utilized to extract that ore can leave behind long-term environmental damage. A potential solution to enhance the supply of uranium fuel is to recover uranium from seawater using amidoximated adsorbent fibers. This technology has been studied for decades but is currently plagued by the material’s relatively poor selectivity of uranium over its main competitormore » vanadium. In this work, we investigate the binding schemes between uranium, vanadium, and the amidoxime functional groups on the adsorbent surface. Using quantum chemical methods, binding strengths are approximated for a set of complexation reactions between uranium and vanadium with amidoxime functionalities. Those approximations are then coupled with a comprehensive aqueous adsorption model developed in this work to simulate the adsorption of uranium and vanadium under laboratory conditions. Experimental adsorption studies with uranium and vanadium over a wide pH range are performed, and the data collected are compared against simulation results to validate the model. It was found that coupling ab initio calculations with process level adsorption modeling provides accurate predictions of the adsorption capacity and selectivity of the sorbent materials. Furthermore, this work demonstrates that this multiscale modeling paradigm could be utilized to aid in the selection of superior ligands or ligand compositions for the selective capture of metal ions. Furthermore, this first-principles integrated modeling approach opens the door to the in silico design of next-generation adsorbents with potentially superior efficiency and selectivity for uranium over vanadium in seawater.« less

First-Principles Integrated Adsorption Modeling for Selective Capture of Uranium from Seawater by Polyamidoxime Sorbent Materials.

PubMed

Ladshaw, Austin P; Ivanov, Alexander S; Das, Sadananda; Bryantsev, Vyacheslav S; Tsouris, Costas; Yiacoumi, Sotira

2018-04-18

Nuclear power is a relatively carbon-free energy source that has the capacity to be utilized today in an effort to stem the tides of global warming. The growing demand for nuclear energy, however, could put significant strain on our uranium ore resources, and the mining activities utilized to extract that ore can leave behind long-term environmental damage. A potential solution to enhance the supply of uranium fuel is to recover uranium from seawater using amidoximated adsorbent fibers. This technology has been studied for decades but is currently plagued by the material's relatively poor selectivity of uranium over its main competitor vanadium. In this work, we investigate the binding schemes between uranium, vanadium, and the amidoxime functional groups on the adsorbent surface. Using quantum chemical methods, binding strengths are approximated for a set of complexation reactions between uranium and vanadium with amidoxime functionalities. Those approximations are then coupled with a comprehensive aqueous adsorption model developed in this work to simulate the adsorption of uranium and vanadium under laboratory conditions. Experimental adsorption studies with uranium and vanadium over a wide pH range are performed, and the data collected are compared against simulation results to validate the model. It was found that coupling ab initio calculations with process level adsorption modeling provides accurate predictions of the adsorption capacity and selectivity of the sorbent materials. Furthermore, this work demonstrates that this multiscale modeling paradigm could be utilized to aid in the selection of superior ligands or ligand compositions for the selective capture of metal ions. Therefore, this first-principles integrated modeling approach opens the door to the in silico design of next-generation adsorbents with potentially superior efficiency and selectivity for uranium over vanadium in seawater.

Multielement statistical evidence for uraniferous hydrothermal activity in sandstones overlying the Phoenix uranium deposit, Athabasca Basin, Canada

NASA Astrophysics Data System (ADS)

Chen, Shishi; Hattori, Keiko; Grunsky, Eric C.

2018-04-01

The Phoenix U deposit, with indicated resources of 70.2 M lb U3O8, occurs along the unconformity between the Proterozoic Athabasca Group sandstones and the crystalline basement rocks. Principal component analysis (PCA) is applied to the compositions of sandstones overlying the deposit. Among PCs, PC1 accounts for the largest variability of U and shows a positive association of U with rare earth elements (REEs) + Y + Cu + B + Na + Mg + Ni + Be. The evidence suggests that U was dispersed into sandstones together with these elements during the uraniferous hydrothermal activity. Uranium shows an inverse association with Zr, Hf, Th, Fe, and Ti. Since they are common in detrital heavy minerals, such heavy minerals are not the major host of U. The elements positively associated with U are high in concentrations above the deposit, forming a "chimney-like" or "hump-like" distribution in a vertical section. Their enrichment patterns are explained by the ascent of basement fluids through faults to sandstones and the circulation of basinal fluids around the deposit. The Pb isotope compositions of whole rocks are similar to expected values calculated from the concentrations of U, Th, and Pb except for sandstones close to the deposit. The data suggest that in situ decay of U and Th is responsible for the Pb isotope compositions of most sandstones and that highly radiogenic Pb dispersed from the deposit to the proximal sandstones long after the mineralization. This secondary dispersion is captured in PC8, which has low eigenvalue. The data suggests that the secondary dispersion has minor effect on the overall lithogeochemistry of sandstones.

Amidoxime Polymers for Uranium Adsorption: Influence of Comonomers and Temperature

DOE PAGES

Ladshaw, Austin P.; Wiechert, Alexander I.; Das, Sadananda; ...

2017-11-04

Recovering uranium from seawater has been the subject of many studies for decades, and has recently seen significant progress in materials development since the U.S. Department of Energy (DOE) has become involved. With DOE direction, the uranium uptake for amidoxime-based polymer adsorbents has more than tripled in capacity. In an effort to better understand how these new adsorbent materials behave under different environmental stimuli, several experimental and modeling based studies have been employed to investigate impacts of competing ions, salinity, pH, and other factors on uranium uptake. For this study, the effect of temperature and type of comonomer on uraniummore » adsorption by three different amidoxime adsorbents (AF1, 38H, AI8) was examined. Experimental measurements of uranium uptake were taken in 1–L batch reactors from 10 to 40 °C. A chemisorption model was developed and applied in order to estimate unknown system parameters through optimization. Experimental results demonstrated that the overall uranium chemisorption process for all three materials is endothermic, which was also mirrored in the model results. Model simulations show very good agreement with the data and were able to predict the temperature effect on uranium adsorption as experimental conditions changed. Here, this model may be used for predicting uranium uptake by other amidoxime materials.« less

Amidoxime Polymers for Uranium Adsorption: Influence of Comonomers and Temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ladshaw, Austin P.; Wiechert, Alexander I.; Das, Sadananda

Recovering uranium from seawater has been the subject of many studies for decades, and has recently seen significant progress in materials development since the U.S. Department of Energy (DOE) has become involved. With DOE direction, the uranium uptake for amidoxime-based polymer adsorbents has more than tripled in capacity. In an effort to better understand how these new adsorbent materials behave under different environmental stimuli, several experimental and modeling based studies have been employed to investigate impacts of competing ions, salinity, pH, and other factors on uranium uptake. For this study, the effect of temperature and type of comonomer on uraniummore » adsorption by three different amidoxime adsorbents (AF1, 38H, AI8) was examined. Experimental measurements of uranium uptake were taken in 1–L batch reactors from 10 to 40 °C. A chemisorption model was developed and applied in order to estimate unknown system parameters through optimization. Experimental results demonstrated that the overall uranium chemisorption process for all three materials is endothermic, which was also mirrored in the model results. Model simulations show very good agreement with the data and were able to predict the temperature effect on uranium adsorption as experimental conditions changed. Here, this model may be used for predicting uranium uptake by other amidoxime materials.« less

A Major Unconformity Between Permian and Triassic Strata at Cape Kekurnoi, Alaska Peninsula: Old and New Observations on Stratigraphy and Hydrocarbon Potential

USGS Publications Warehouse

Blodgett, Robert B.; Sralla, Bryan

2008-01-01

A major angular unconformity separates carbonates and shales of the Upper Triassic Kamishak Formation from an underlying unnamed sequence of Permian agglomerate, volcaniclastic rocks (sandstone), and limestone near Puale Bay on the Alaska Peninsula. For the first time, we photographically document the angular unconformity in outcrop, as clearly exposed in a seacliff ~1.3 mi (2.1 km) west of Cape Kekurnoi in the Karluk C?4 and C?5 1:63,360-scale quadrangles. This unconformity is also documented by examination of core chips, ditch cuttings, and (or) open-hole electrical logs in two deep oil-and-gas-exploration wells (Humble Oil & Refining Co.?s Bear Creek No. 1 and Standard Oil Co. of California?s Grammer No. 1) drilled along the Alaska Peninsula southwest of Puale Bay. A third well (Richfield Oil Corp.?s Wide Bay Unit No. 1), south of and structurally on trend with the other two wells, probed deeply into the Paleozoic basement, but Triassic strata are absent, owing to either a major unconformity or a large fault. Here we briefly review current and newly acquired data on Permian and Triassic rocks of the Puale Bay-Becharof Lake-Wide Bay area on the basis of an examination of surface and subsurface materials. The resulting reinterpretation of the Permian and Triassic stratigraphy has important economic ramifications for oil and gas exploration on the Alaska Peninsula and in the Cook Inlet basin. We also present a history of petroleum exploration targeting Upper Triassic reservoirs in the region.

Late Jurassic – early Cretaceous inversion of rift structures, and linkage of petroleum system elements across post-rift unconformity, U.S. Chukchi Shelf, arctic Alaska

USGS Publications Warehouse

Houseknecht, David W.; Connors, Christopher D.

2015-01-01

Oil-prone source rocks, reservoir-quality sandstone, migration pathways, and structural closure are linked intimately across the Jurassic unconformity, which reflects inversion. Thus, all these key petroleum systems elements were in place when Triassic source rocks entered the oil generation window during Cretaceous–Cenozoic stratigraphic burial.

Uranium Associations with Kidney Outcomes Vary by Urine Concentration Adjustment Method

PubMed Central

Shelley, Rebecca; Kim, Nam-Soo; Parsons, Patrick J.; Lee, Byung-Kook; Agnew, Jacqueline; Jaar, Bernard G.; Steuerwald, Amy J.; Matanoski, Genevieve; Fadrowski, Jeffrey; Schwartz, Brian S.; Todd, Andrew C.; Simon, David; Weaver, Virginia M.

2017-01-01

Uranium is a ubiquitous metal that is nephrotoxic at high doses. Few epidemiologic studies have examined the kidney filtration impact of chronic environmental exposure. In 684 lead workers environmentally exposed to uranium, multiple linear regression was used to examine associations of uranium measured in a four-hour urine collection with measured creatinine clearance, serum creatinine- and cystatin-C-based estimated glomerular filtration rates, and N-acetyl-β-D-glucosaminidase (NAG). Three methods were utilized, in separate models, to adjust uranium levels for urine concentration - μg uranium/g creatinine; μg uranium/L and urine creatinine as separate covariates; and μg uranium/4 hr. Median urine uranium levels were 0.07 μg/g creatinine and 0.02 μg/4 hr and were highly correlated (rs =0.95). After adjustment, higher ln-urine uranium was associated with lower measured creatinine clearance and higher NAG in models that used urine creatinine to adjust for urine concentration but not in models that used total uranium excreted (μg/4 hr). These results suggest that, in some instances, associations between urine toxicants and kidney outcomes may be statistical, due to the use of urine creatinine in both exposure and outcome metrics, rather than nephrotoxic. These findings support consideration of non-creatinine-based methods of adjustment for urine concentration in nephrotoxicant research. PMID:23591699

Experiments and Modeling of Uranium Adsorption in the Presence of Other Ions in Simulated Seawater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ladshaw, Austin; Das, Sadananda; Liao, Wei-Po

2015-11-19

Seawater contains uranium at an average concentration of 3.3 ppb, as well as a variety of other ions at either overwhelmingly higher or similar concentrations, which complicate the recovery of uranium. This report describes an investigation of the effects of various factors such as uranium speciation and presence of salts including sodium, calcium, magnesium, and bicarbonate, as well as trace elements such as vanadium on uranium adsorption kinetics in laboratory experiments. Adsorption models are also developed to describe the experimental data of uranium extraction from seawater. Results show that the presence of calcium and magnesium significantly slows down the uraniummore » adsorption kinetics. Vanadium can replace uranium from amidoxime-based adsorbent in the presence of sodium in the solution. Results also show that bicarbonate in the solution strongly competes with amidoxime for binding uranium, and thus slows down the uranium adsorption kinetics. Developed on the basis of the experimental findings, the model is capable of describing the effects of pH, ionic strength, temperature, and concentration of various species. The results of this work are useful in the understanding of the important factors that control the adsorbent capacity and kinetics of uranium uptake by amidoxime-based adsorbents.« less

Allostratigraphy of the U.S. middle Atlantic continental margin; characteristics, distribution, and depositional history of principal unconformity-bounded upper Cretaceous and Cenozoic sedimentary units

USGS Publications Warehouse

Poag, C. Wylie; Ward, Lauck W.

1993-01-01

Publication of Volumes 93 and 95 ('The New Jersey Transect') of the Deep Sea Drilling Project's Initial Reports completed a major phase of geological and geophysical research along the middle segment of the U. S. Atlantic continental margin. Relying heavily on data from these and related published records, we have integrated outcrop, borehole, and seismic-reflection data from this large area (500,000 km^2 ) to define the regional allostratigraphic framework for Upper Cretaceous and Cenozoic sedimentary rocks. The framework consists of 12 alloformations, which record the Late Cretaceous and Cenozoic depositional history of the contiguous Baltimore Canyon trough (including its onshore margin) and Hatteras basin (northern part). We propose stratotype sections for each alloformation and present a regional allostratigraphic reference section, which crosses these basins from the inner edge of the coastal plain to the inner edge of the abyssal plain. Selected supplementary reference sections on the coastal plain allow observation of the alloformations and their bounding unconformities in outcrop. Our analyses show that sediment supply and its initial dispersal on the middle segment of the U. S. Atlantic margin have been governed, in large part, by hinterland tectonism and subsequently have been modified by paleoclimate, sea-level changes, and oceanic current systems. Notable events in the Late Cretaceous to Holocene sedimentary evolution of this margin include (1) development of continental-rise depocenters in the northern part of the Hatteras basin during the Late Cretaceous; (2) the appear ance of a dual shelf-edge system, a marked decline in siliciclastic sediment accumulation rates, and widespread acceleration of carbonate production during high sea levels of the Paleogene; (3) rapid deposition and progradation of thick terrigenous delta complexes and development of abyssal depocenters during the middle Miocene to Quaternary interval; and (4) deep incision of the shelf edge by submarine canyons, especially during the Pleistocene. Massive downslope gravity flows have dominated both the depositional and erosional history of the middle segment of the U. S. Atlantic Continental Slope and Rise during most of the last 84 million years. The importance of periodic widespread erosion is recorded by well-documented unconformities, many of which can be traced from coastal-plain outcrops to coreholes on the continental slope and lower continental rise. These unconformities form the boundaries of the 12 allostratigraphic units we formally propose herein. Seven of the unconformities correlate with supercycle boundaries (sequence boundaries) that characterize the Exxon sequence-stratigraphy model.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nibbelink, K.A.; Sorgenfrei, M.C.; Rice, D.E.

Yombo field in the Congo is sourced from the lacustrine shales of the presalt rift stage and produces from the Albian and Cenomanian, postsalt, Sendji carbonate and Tchala Sandstone. The Yombo prospect exploration model included an upper Sendji stratigraphic trap with two components and a structural nose. The buried hill component of the trap is formed by topographic relief on the reservoir below the top Sendji unconformity. The lower Sendji slump blocks provide a high on which the upper Sendji grainstone shoal facies develop. Both depositional relief and erosion during the top Sendji unconformity contribute to the topography. An isochronmore » thick in the overlying Tchala valley-fill sediments defined a drainage pattern on the unconformity around the buried hill of the underlying upper Sendji. The facies change component is formed by the pinch-out of the grainstone shoal reservoir facies into porous, but impermeable lagoonal dolomite interbedded with anhydrite and shale. Capillary pressure measurements on the 16% porosity, 0.1 md permeability lagoonal dolomite, along with pore throat radius and buoyancy calculations, demonstrated this facies could trap a significant column of low-gravity oil at shallow depth. The Tchala Sandstone contains several separate hydrocarbon accumulations. A stratigraphic trap in the lower Tchala is formed by marine and tidal channel sandstones pinching out into lagoonal shales. The nearshore marine sandstones of the upper Tchala contain additional hydrocarbons in structural and stratigraphic traps. The stratigraphic pinch-out that cross the Yombo nose trap a significant hydrocarbon accumulation, even though the four-way structural closure is relatively small.« less

A model of early formation of uranium molecular oxides in laser-ablated plasmas

NASA Astrophysics Data System (ADS)

Finko, Mikhail S.; Curreli, Davide; Weisz, David G.; Crowhurst, Jonathan C.; Rose, Timothy P.; Koroglu, Batikan; Radousky, Harry B.; Armstrong, Michael R.

2017-12-01

In this work, we present a newly constructed U x O y reaction mechanism that consists of 30 reaction channels (21 of which are reversible channels) for 11 uranium molecular species (including ions). Both the selection of reaction channels and calculation of corresponding rate coefficients is accomplished via a comprehensive literature review and application of basic reaction rate theory. The reaction mechanism is supplemented by a detailed description of oxygen plasma chemistry (19 species and 142 reaction channels) and is used to model an atmospheric laser ablated uranium plume via a 0D (global) model. The global model is used to analyze the evolution of key uranium molecular species predicted by the reaction mechanism, and the initial stage of formation of uranium oxide species.

Spatial analysis techniques applied to uranium prospecting in Chihuahua State, Mexico

NASA Astrophysics Data System (ADS)

Hinojosa de la Garza, Octavio R.; Montero Cabrera, María Elena; Sanín, Luz H.; Reyes Cortés, Manuel; Martínez Meyer, Enrique

2014-07-01

To estimate the distribution of uranium minerals in Chihuahua, the advanced statistical model "Maximun Entropy Method" (MaxEnt) was applied. A distinguishing feature of this method is that it can fit more complex models in case of small datasets (x and y data), as is the location of uranium ores in the State of Chihuahua. For georeferencing uranium ores, a database from the United States Geological Survey and workgroup of experts in Mexico was used. The main contribution of this paper is the proposal of maximum entropy techniques to obtain the mineral's potential distribution. For this model were used 24 environmental layers like topography, gravimetry, climate (worldclim), soil properties and others that were useful to project the uranium's distribution across the study area. For the validation of the places predicted by the model, comparisons were done with other research of the Mexican Service of Geological Survey, with direct exploration of specific areas and by talks with former exploration workers of the enterprise "Uranio de Mexico". Results. New uranium areas predicted by the model were validated, finding some relationship between the model predictions and geological faults. Conclusions. Modeling by spatial analysis provides additional information to the energy and mineral resources sectors.

A new species of Dyoros (Brachiopoda; Chonetoidea) from Nevada (United States) and stratigraphic implications for the Pennsylvanian and Permian Antler Overlap assemblage [Une nouvelle espèce de Dyoros (Brachiopoda; Chonetoidea) du Nevada (États-Unis) et implications stratigraphiques pour le Complexe chevauchant d'Antler (Pennsylvanien et Permien)

USGS Publications Warehouse

Racheboeuf, Patrick R.; Moore, Thomas E.; Blodgett, Robert B.

2004-01-01

Newly discovered fossil localities in coarse-grained deposits of the Pennsylvanian and Permian Antler overlap assemblage in the southern Shoshone Range, north-central Nevada have yielded a low-diversity assemblage consisting chiefly of a new species of chonetoidean brachiopod: Dyoros (Lissosia) nevadaensis nov. sp. The subgenus Dyoros (Lissosia), is known from Leonardian and lower Guadalupian strata in North America, mainly in Texas. The coarse-grained lithology of the host strata, their unconformable relation on deformed lower Paleozoic rocks, and the Leonardian and(or) lower Guadalupian age indicated by Dyoros (Lissosia) provide evidence that host strata are younger than strata of the Antler overlap assemblage in nearby areas of the southern Shoshone Range and suggest that an unconformity of local extent may be present within the overlap assemblage. The fossil age ranges and lithologic data suggest that the host strata may be correlative with the Guadalupian Edna Mountain Formation, an unconformity-bounded unit that forms the upper part of the Antler sequence in the Battle Mountain area to the north. This correlation suggests that the unconformity beneath these strata may have regional extent in north-central Nevada. The origin of the inferred regional unconformity is unknown and may have resulted from relative changes of sea level or regional extensional or contractional tectonism in the area of the former Antler highlands, which forms the substrate for the Antler overlap assemblage. ?? 2004 Elsevier SAS. All rights reserved.

A 3-D morphometric analysis of erosional features in a contourite drift from offshore SE Brazil

NASA Astrophysics Data System (ADS)

Alves, Tiago M.

2010-12-01

A contourite drift from offshore Brazil is mapped in detail and investigated using state-of-the-art 3-D seismic data. The aim was to review the relevance of erosional features in contourite drifts accumulated on continental slopes. Topographically confined by growing salt diapirs, the mapped contourite ridge is limited by two erosional features, a contourite moat and a turbidite channel, showing multiple slide scars on it flanks. Associated with the latter features are thick accumulations of high-amplitude strata, probably comprising sandy/silty sediment of Miocene to Holocene age. The erosional unconformities are mostly observed in a region averaging 3.75km away from the axes of a channel and a moat, whose deposits interfinger with continuous strata in central parts of the contourite drift. The multiple unconformities observed are mostly related to slide scars and local erosion on the flanks of the drift. This work demonstrates that the existence of widespread unconformities within contourite drifts on continental slopes: (1) may not be as prominent as often documented, (2) are often diachronic and interfinger with correlative hiatuses or aggraded strata in axial regions of contourite drifts. Although less widespread than regional, or ocean-scale unconformities, these diachronous features result in significant hiatuses within contourite drifts and are, therefore, potentially mappable as relevant (regional-scale) unconformities on 2-D/3-D seismic data. Thus, without a full 3-D morphometric analysis of contourite drifts, significant errors may occur when estimating major changes in the dynamics of principal geostrophic currents based on single-site core data, or on direct correlations between stratigraphic surfaces of distinct contourite bodies.

Model-Based Analysis of the Role of Biological, Hydrological and Geochemical Factors Affecting Uranium Bioremediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Jiao; Scheibe, Timothy D.; Mahadevan, Radhakrishnan

2011-01-24

Uranium contamination is a serious concern at several sites motivating the development of novel treatment strategies such as the Geobacter-mediated reductive immobilization of uranium. However, this bioremediation strategy has not yet been optimized for the sustained uranium removal. While several reactive-transport models have been developed to represent Geobacter-mediated bioremediation of uranium, these models often lack the detailed quantitative description of the microbial process (e.g., biomass build-up in both groundwater and sediments, electron transport system, etc.) and the interaction between biogeochemical and hydrological process. In this study, a novel multi-scale model was developed by integrating our recent model on electron capacitancemore » of Geobacter (Zhao et al., 2010) with a comprehensive simulator of coupled fluid flow, hydrologic transport, heat transfer, and biogeochemical reactions. This mechanistic reactive-transport model accurately reproduces the experimental data for the bioremediation of uranium with acetate amendment. We subsequently performed global sensitivity analysis with the reactive-transport model in order to identify the main sources of prediction uncertainty caused by synergistic effects of biological, geochemical, and hydrological processes. The proposed approach successfully captured significant contributing factors across time and space, thereby improving the structure and parameterization of the comprehensive reactive-transport model. The global sensitivity analysis also provides a potentially useful tool to evaluate uranium bioremediation strategy. The simulations suggest that under difficult environments (e.g., highly contaminated with U(VI) at a high migration rate of solutes), the efficiency of uranium removal can be improved by adding Geobacter species to the contaminated site (bioaugmentation) in conjunction with the addition of electron donor (biostimulation). The simulations also highlight the interactive effect of initial cell concentration and flow rate on U(VI) reduction.« less

Progress report on geologic studies of the Ranger orebodies, Northern Territory, Australia

USGS Publications Warehouse

Nash, J.T.; Frishman, David

1982-01-01

The Ranger No. 1 and No. 3 orebodies contain about 124,000 tonnes U3O8 in highly chloritized metasediments of the lower Proterozoic Cahill Formation within about 500 m of the projected sub-Kombolgie Formation unconformity. In both orebodies, oxidized and reduced uranium minerals occur chiefly in quartzose schists that have highly variable amounts of muscovite, sericite, and chlorite. The effects of several periods of alteration are pervasive in the vicinity of orebodies where biotite and garnet are altered to chlorite, and feldspars to white mica or chlorite. Oxidized uranium minerals, associated with earthy iron oxides, occur from the surface to a depth of about 60 m. Below the oxidized zone, uranium occurs chiefly as uraninite and pitchblende disseminated through thick sections of quartz-chlorite-muscovite schist and has no apparent association with graphite or sulfides. In fact, graphite is rare and sulfides are generally low in abundance (<0.5 percent). Higher ore grades occur in disrupted zones a few centimeters thick and in some quartz-chlorite vein-like zones of uncertain origin. Uranium correlates strongly with chlorite, but not all of the many ages of chlorite have associated uranium. At least five textural varieties of chlorite are present and represent at least 3 ages. Preliminary microprobe analyses suggest that Mg-Fe-Al contents are relatively uniform. Apatite commonly occurs with chlorite. Uranium is not common in carbonate rocks and seems to occur only in disrupted zones that have chlorite alteration. Chloritization and silicification are more widespread and intense in the No. 1 orebody than in the No. 3. In both orebodies, hematite occurs tens to hundreds of meters below the weathered zone, in both altered and largely unaltered rocks, with and without uranium. The structure of the orebodies is outwardly simple, particularly in No. 3; dips are less than 40? on most lithologic contacts. The No. 1 orebody is in a basin-like structure about 400 m wide that probably formed in part by progressive removal of carbonate rocks that are as much as 200 m thick adjacent to the No. 1 orebody and below the No. 3 orebody. Quartz-chlorite breccias have formed in the zone of carbonate thinning; uranium is spotty and low grade in these breccias. Chloritized and uraniferous broken and sheared zones, a few centimeters to a few meters thick, have an unknown attitude but must have small displacement. Blocks of altered Kombolgie sandstone are downfaulted into the No. 3 orebody and locally contain reduced uranium minerals. One or more shear zones 5-30 m thick of crushed and smeared fine to coarse rock fragments occur below the orebodies, and other low-angle shears probably occur in the orebodies. The shear zone dips about 40 o and displacement on it is not known. The footwall rocks generally are less retrograded than those in the hanging wall (orebody) and consist of quartz-biotite-feldspar schists and gneisses flanking the Nanambu Complex. A few scattered fractures in the footwall sequence contain pitchblende of unknown age and origin. Major element chemical analyses confirm the lithologic observations of large changes in composition during multiple stages of alteration. Granitic dikes and pelitic schists have gained Fe and Mg and lost Si, Ca, Na, and K during chloritization. Marbles have gained Si, Al, Fe, and P, and lost Mg, Ca, and K during jasperoid-chlorite alteration. Total net chemical gains and losses in the Ranger No. 1 orebody were huge: equal to about 37 percent of the mass of the ore-bearing rock that will be mined. There were net gains in Si and P and net losses in Al, Fe, Mg, Ca, K, and Na. The geologic age(s) of uranium emplacement are obscure because there are few age criteria. Reduced uranium minerals are younger than 1.8-b.y.-old granite dikes, and some occur locally in 1.65-b.y.-old Kombolgie Formation. Diabase dikes (age not known) are thoroughly chloritized and contain sparse ore minerals. Oxidized ura

Chronic Exposure to Uranium from Gestation: Effects on Behavior and Neurogenesis in Adulthood

PubMed Central

Dinocourt, Céline; Culeux, Cécile; Legrand, Marie; Elie, Christelle; Lestaevel, Philippe

2017-01-01

Uranium exposure leads to cerebral dysfunction involving for instance biochemical, neurochemical and neurobehavioral effects. Most studies have focused on mechanisms in uranium-exposed adult animals. However, recent data on developing animals have shown that the developing brain is also sensitive to uranium. Models of uranium exposure during brain development highlight the need to improve our understanding of the effects of uranium. In a model in which uranium exposure began from the first day of gestation, we studied the neurobehavioral consequences as well as the progression of hippocampal neurogenesis in animals from dams exposed to uranium. Our results show that 2-month-old rats exposed to uranium from gestational day 1 displayed deficits in special memory and a prominent depressive-like phenotype. Cell proliferation was not disturbed in these animals, as shown by 5-bromo-2′deoxyuridine (BrdU)/neuronal specific nuclear protein (NeuN) immunostaining in the dentate gyrus. However, in some animals, the pyramidal cell layer was dispersed in the CA3 region. From our previous results with the same model, the hypothesis of alterations of neurogenesis at prior stages of development is worth considering, but is probably not the only one. Therefore, further investigations are needed to correlate cerebral dysfunction and its underlying mechanistic pathways. PMID:28513543

Chronic Exposure to Uranium from Gestation: Effects on Behavior and Neurogenesis in Adulthood.

PubMed

Dinocourt, Céline; Culeux, Cécile; Legrand, Marie; Elie, Christelle; Lestaevel, Philippe

2017-05-17

Uranium exposure leads to cerebral dysfunction involving for instance biochemical, neurochemical and neurobehavioral effects. Most studies have focused on mechanisms in uranium-exposed adult animals. However, recent data on developing animals have shown that the developing brain is also sensitive to uranium. Models of uranium exposure during brain development highlight the need to improve our understanding of the effects of uranium. In a model in which uranium exposure began from the first day of gestation, we studied the neurobehavioral consequences as well as the progression of hippocampal neurogenesis in animals from dams exposed to uranium. Our results show that 2-month-old rats exposed to uranium from gestational day 1 displayed deficits in special memory and a prominent depressive-like phenotype. Cell proliferation was not disturbed in these animals, as shown by 5-bromo-2'deoxyuridine (BrdU)/neuronal specific nuclear protein (NeuN) immunostaining in the dentate gyrus. However, in some animals, the pyramidal cell layer was dispersed in the CA3 region. From our previous results with the same model, the hypothesis of alterations of neurogenesis at prior stages of development is worth considering, but is probably not the only one. Therefore, further investigations are needed to correlate cerebral dysfunction and its underlying mechanistic pathways.

Descriptive models of major uranium deposits in China - Some results of the Workshop on Uranium Resource Assessment sponsored by the International Atomic Energy Agency, Vienna, Austria, in cooperation with China National Nuclear Corporation, Beijing, and the U.S. Geological Survey, Denver, Colorado, and Reston, Virginia

USGS Publications Warehouse

Finch, W.I.; Feng, S.; Zuyi, C.; McCammon, R.B.

1993-01-01

Four major types of uranium deposits occur in China: granite, volcanic, sandstone, and carbonaceous-siliceous-pelitic rock. These types are major sources of uranium in many parts of the world and account for about 95 percent of Chinese production. Descriptive models for each of these types record the diagnostic regional and local geologic features of the deposits that are important to genetic studies, exploration, and resource assessment. A fifth type of uranium deposit, metasomatite, is also modeled because of its high potential for production. These five types of uranium deposits occur irregularly in five tectonic provinces distributed from the northwest through central to southern China. ?? 1993 Oxford University Press.

Cryostratigraphy and the Sublimation Unconformity in Permafrost from an Ultraxerous Environment, University Valley, McMurdo Dry Valleys of Antarctica

NASA Technical Reports Server (NTRS)

Lapalme, Caitlin M.; Fortier, Daniel; Pollard, Wayne; Lacelle, Denis; Davila, Alfonso; McKay, Christopher P.

2017-01-01

The cryostratigraphy of permafrost in ultraxerous environments is poorly known. In this study, icy permafrost cores from University Valley (McMurdo Dry Valleys, Antarctica) were analyzed for sediment properties, ground-ice content, types and distribution of cryostructures, and presence of unconformities. No active layer exists in the valley, but the ice table, a sublimation unconformity, ranges from 0 to 60 cm depth. The sediments are characterized as a medium sand, which classifies them as low to non-frost susceptible. Computed tomography (CT) scan images of the icy permafrost cores revealed composite cryostructures that included the structureless, porous visible, suspended and crustal types. These cryostructures were observed irrespective of ground-ice origin (vapour deposited and freezing of snow meltwater), suggesting that the type and distribution of cryostructures could not be used as a proxy to infer the mode of emplacement of ground ice. Volumetric ice content derived from the CT scan images underestimated measured volumetric ice content, but approached measured excess ice content. A palaeo-sublimation unconformity could not be detected from a change in cryostructures, but could be inferred from an increase in ice content at the maximum predicted ice table depth. This study highlights some of the unique ground-ice processes and cryostructures in ultraxerous environments.

A model of early formation of uranium molecular oxides in laser-ablated plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finko, Mikhail S.; Curreli, Davide; Weisz, David G.

Here, in this work, we present a newly constructed U xO y reaction mechanism that consists of 30 reaction channels (21 of which are reversible channels) for 11 uranium molecular species (including ions). Both the selection of reaction channels and calculation of corresponding rate coefficients is accomplished via a comprehensive literature review and application of basic reaction rate theory. The reaction mechanism is supplemented by a detailed description of oxygen plasma chemistry (19 species and 142 reaction channels) and is used to model an atmospheric laser ablated uranium plume via a 0D (global) model. Finally, the global model is usedmore » to analyze the evolution of key uranium molecular species predicted by the reaction mechanism, and the initial stage of formation of uranium oxide species.« less

A model of early formation of uranium molecular oxides in laser-ablated plasmas

DOE PAGES

Finko, Mikhail S.; Curreli, Davide; Weisz, David G.; ...

2017-10-12

Here, in this work, we present a newly constructed U xO y reaction mechanism that consists of 30 reaction channels (21 of which are reversible channels) for 11 uranium molecular species (including ions). Both the selection of reaction channels and calculation of corresponding rate coefficients is accomplished via a comprehensive literature review and application of basic reaction rate theory. The reaction mechanism is supplemented by a detailed description of oxygen plasma chemistry (19 species and 142 reaction channels) and is used to model an atmospheric laser ablated uranium plume via a 0D (global) model. Finally, the global model is usedmore » to analyze the evolution of key uranium molecular species predicted by the reaction mechanism, and the initial stage of formation of uranium oxide species.« less

A model of early formation of uranium molecular oxides in laser-ablated plasmas

NASA Astrophysics Data System (ADS)

Finko, Mikhail; Curreli, Davide; Azer, Magdi; Weisz, David; Crowhurst, Jonathan; Rose, Timothy; Koroglu, Batikan; Radousky, Harry; Zaug, Joseph; Armstrong, Mike

2017-10-01

An important problem within the field of nuclear forensics is fractionation: the formation of post-detonation nuclear debris whose composition does not reflect that of the source weapon. We are investigating uranium fractionation in rapidly cooling plasma using a combined experimental and modeling approach. In particular, we use laser ablation of uranium metal samples to produce a low-temperature plasma with physical conditions similar to a condensing nuclear fireball. Here we present a first plasma-chemistry model of uranium molecular species formation during the early stage of laser ablated plasma evolution in atmospheric oxygen. The system is simulated using a global kinetic model with rate coefficients calculated according to literature data and the application of reaction rate theory. The model allows for a detailed analysis of the evolution of key uranium molecular species and represents the first step in producing a uranium fireball model that is kinetically validated against spatially and temporally resolved spectroscopy measurements. This project was sponsored by the DoD, Defense Threat Reduction Agency, Grant HDTRA1-16- 1-0020. This work was performed in part under the auspices of the U.S. DoE by Lawrence Livermore National Laboratory under Contract DE-AC52- 07NA27344.

Conceptual Model of Uranium in the Vadose Zone for Acidic and Alkaline Wastes Discharged at the Hanford Site Central Plateau

DOE Office of Scientific and Technical Information (OSTI.GOV)

Truex, Michael J.; Szecsody, James E.; Qafoku, Nikolla

2014-09-01

Historically, uranium was disposed in waste solutions of varying waste chemistry at the Hanford Site Central Plateau. The character of how uranium was distributed in the vadose zone during disposal, how it has continued to migrate through the vadose zone, and the magnitude of potential impacts on groundwater are strongly influenced by geochemical reactions in the vadose zone. These geochemical reactions can be significantly influenced by the disposed-waste chemistry near the disposal location. This report provides conceptual models and supporting information to describe uranium fate and transport in the vadose zone for both acidic and alkaline wastes discharged at amore » substantial number of waste sites in the Hanford Site Central Plateau. The conceptual models include consideration of how co-disposed acidic or alkaline fluids influence uranium mobility in terms of induced dissolution/precipitation reactions and changes in uranium sorption with a focus on the conditions near the disposal site. This information, when combined with the extensive information describing uranium fate and transport at near background pH conditions, enables focused characterization to support effective fate and transport estimates for uranium in the subsurface.« less

Uranium Fate and Transport Modeling, Guterl Specialty Steel Site, New York - 13545

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frederick, Bill; Tandon, Vikas

2013-07-01

The Former Guterl Specialty Steel Corporation Site (Guterl Site) is located 32 kilometers (20 miles) northeast of Buffalo, New York, in Lockport, Niagara County, New York. Between 1948 and 1952, up to 15,875 metric tons (35 million pounds) of natural uranium metal (U) were processed at the former Guterl Specialty Steel Corporation site in Lockport, New York. The resulting dust, thermal scale, mill shavings and associated land disposal contaminated both the facility and on-site soils. Uranium subsequently impacted groundwater and a fully developed plume exists below the site. Uranium transport from the site involves legacy on-site pickling fluid handling, themore » leaching of uranium from soil to groundwater, and the groundwater transport of dissolved uranium to the Erie Canal. Groundwater fate and transport modeling was performed to assess the transfer of dissolved uranium from the contaminated soils and buildings to groundwater and subsequently to the nearby Erie Canal. The modeling provides a tool to determine if the uranium contamination could potentially affect human receptors in the vicinity of the site. Groundwater underlying the site and in the surrounding area generally flows southeasterly towards the Erie Canal; locally, groundwater is not used as a drinking water resource. The risk to human health was evaluated outside the Guterl Site boundary from the possibility of impacted groundwater discharging to and mixing with the Erie Canal waters. This condition was evaluated because canal water is infrequently used as an emergency water supply for the City of Lockport via an intake located approximately 122 meters (m) (400 feet [ft]) southeast of the Guterl Site. Modeling was performed to assess whether mixing of groundwater with surface water in the Erie Canal could result in levels of uranium exceeding the U.S. Environmental Protection Agency (USEPA) established drinking water standard for total uranium; the Maximum Concentration Limit (MCL). Geotechnical test data indicate that the major portion of uranium in the soil will adsorb or remain bound to soil, yet leaching to groundwater appears as an on-site source. Soil leaching was modeled using low adsorption factors to replicate worst-case conditions where the uranium leaches to the groundwater. Results indicate that even after several decades, which is the period of time since uranium was processed at the Guterl Site, leaching from soil does not fully account for the currently observed levels of groundwater contamination. Modeling results suggest that there were historic releases of uranium from processing operations directly to the shallow fractured rock and possibly other geochemical conditions that have produced the current groundwater contamination. Groundwater data collected at the site between 1997 and 2011 do not indicate an increasing level of uranium in the main plume, thus the uranium adsorbed to the soil is in equilibrium with the groundwater geochemistry and transport conditions. Consequently, increases in the overall plume concentration or size are not expected. Groundwater flowing through fractures under the Guterl Site transports dissolved uranium from the site to the Erie Canal, where the groundwater has been observed to seep from the northern canal wall at some locations. The seeps discharge uranium at concentrations near or below the MCL to the Erie Canal. Conservative mixing calculations were performed using two worst-case assumptions: 1) the seeps were calculated as contiguous discharges from the Erie Canal wall and 2) the uranium concentration of the seepage is 274 micrograms per liter (μg/L) of uranium, which is the highest on-site uranium concentration in groundwater and nearly ten-fold the actual seep concentrations. The results indicate that uranium concentrations in the seep water would have to be more than 200 times greater than the highest observed on-site groundwater concentrations (or nearly 55,000 μg/L) to potentially exceed the drinking water standard (the MCL) for total uranium in the Erie Canal. (authors)« less

Relation of the lower Pennsylvanian unconformity to a mid-carboniferous eustatic event in the eastern United States

USGS Publications Warehouse

Englund, K.J.; Thomas, R.E.

1997-01-01

Two contrasting concepts specifying the age and duration of the hiatus resulting from a mid-Carboniferous eustatic event in the eastern United States are based on different evidence. The original model indicated that the hiatus is at an unconformity in cratonic areas that was assumed to coincide with the Mississippian-Pennsylvanian boundary at the contact between the Mississippian Bluestone Formation and the Pennsylvanian Pocahontas Formation in the Appalachian foreland basin. This concept was adhered to exclusively until 1969 and continues to reappear in reports dealing with global correlations and division of the Carboniferous into the Mississippian and Pennsylvanian Systems. This division is at a major eustatic event that supposedly occurred at about 330 Ma in scattered parts of the world, including the Appalachian basin. An alternative concept, fully supported by geologic mapping and biostratigraphic studies, indicates that the unconformity and associated hiatus are much younger because they originate in the Appalachian foreland basin in the lower part (upper Namurian) of the Lower Pennsylvanian New River Formation, about 260 m above the Mississippian-Pennsylvanian boundary. The duration of this hiatus increases in a northwesterly direction onto the cratonic shelf because the unconformity progressively truncated the underlying Lower Pennsylvanian and Upper Mississippian successions. The westward onlap of Pennsylvanian strata onto the eroded surface resulted in a hiatus from the Early Mississippian (Tournaisian) to the Middle Pennsylvanian (Westphalian B). The systemic boundary, which is in a depositional continuous sequence of strata in the Appalachian foreland basin, was correlated biostratigraphically by Pfefferkorn and Gillespie in 1982 with Gothan's "Florensprung" (floral break) described in 1913 at the Namurian A-B boundary in the Upper Silesian basin. An intra-Namurian erosive event was noted also in the Upper Silesian basin by Havlena, who reported in 1982 that an intra-Namurian erosive contact occurs well above the Florensprung. The origin of the Florensprung in depositional continuous strata has been attributed to tectonism, environment, or climate. However, spherules found in depositional continuous strata near the Mississippian-Pennsylvanian boundary in the Appalachian basin indicate that the effect of an asteroid impact may be the underlying cause for the biodiversity noted at the systemic boundary.

Principal unconformities in Triassic and Jurassic rocks, western interior United States; a preliminary survey

USGS Publications Warehouse

Pipiringos, G.N.; O'Sullivan, Robert Brett

1978-01-01

The Triassic and Jurassic rocks in Western Interior United States contain nine unconformities each of which was destroyed to some extent by a younger unconformity. Regardless of extent, all are useful for correlation of rock sequences in areas where fossils or age dates are lacking. The purpose of this report is to call attention to the presence, significance, and value for correlation of these unconformities. The Triassic unconformities are designated from oldest to youngest, Tr-1, Tr-2, and Tr-3; the Jurassic ones similarly are designated J-0, J-l, J-2, J-3, J-4, and J-5. Of these, the J-2 surface is the best preserved and most widespread. It extends throughout the Western Interior and truncates the older unconformities in different parts of this area. Consequently, the J-2 surface is discussed and illustrated in much more detail than the others. Identification of these unconformities throughout large areas where their presence hitherto had been unknown results in some new unexpected correlations and conclusions. Principal among these are: (1) The Red Draw Member of the Jelm Formation of southeastern Wyoming equals the lower part of the Crow Mountain Sandstone of central Wyoming. The Sips Creek Member of the Jelm Formation of southeastern Wyoming equals the upper part of the Crow Mountain Sandstone of central Wyoming and the Gartra Member of the Chinle Formation in the Uinta Mountains of northeastern Utah and northwestern Colorado. The Chinle Formation of the Colorado Plateau and the Uinta Mountains equals the upper part of the Crow Mountain plus the Popo Agie Formation of central Wyoming. (2) The Nugget Sandstone of northern Utah and southwestern Wyoming approximately equals the Glen Canyon Group of the Colorado Plateau. The Temple Cap Sandstone of southwestern Utah equals the Gypsum Spring Formation and the Gypsum Spring Member of the Twin Creek Limestone of Wyoming and the Nesson Formation of Nordquist in the subsurface of the Williston basin. The Sawtooth and Piper Formations at their type sections in Montana and the lower parts of the Twin Creek Limestone (including only the Sliderock, Rich, and Boundary Ridge Members) in western Wyoming and of the Carmel Formation in the Colorado Plateau, at their respective type localities, are equivalent, but none of these correlate with any part of the Gypsum Spring Formation of Wyoming. The Curtis Formation at its type locality in the San Rafael Swell, Utah, equals only the lower part of the Curtis Formation of the Uinta Mountains. The upper part of the Curtis in the Uinta Mountains and the Redwater Shale Member of the Sundance Formation of Wyoming and South Dakota are equivalent. Estimates of the length of time in millions of years (m.y.) required for uplift and erosion of an unconformity range from less than 1 to as much as 10 m.y.; the average is about 1.8 m.y. if the extremes in time are excluded. The length of time for burial of the surfaces by transgression ranges from less than 1 to about 10 m.y.; the average is less than 1 m.y. if the extremes in time are disregarded.

Uranium removal from aqueous solution by coir pith: equilibrium and kinetic studies.

PubMed

Parab, Harshala; Joshi, Shreeram; Shenoy, Niyoti; Verma, Rakesh; Lali, Arvind; Sudersanan, M

2005-07-01

Basic aspects of uranium adsorption by coir pith have been investigated by batch equilibration. The influence of different experimental parameters such as final solution pH, adsorbent dosage, sorption time, temperature and various concentrations of uranium on uptake were evaluated. Maximum uranium adsorption was observed in the pH range 4.0-6.0. The Freundlich and Langmuir adsorption models were used for the mathematical description of the adsorption equilibrium. The equilibrium data fitted well to both the equilibrium models in the studied concentration range of uranium (200-800 mg/l) and temperatures (305-336 K). The coir pith exhibited the highest uptake capacity for uranium at 317 K, at the final solution pH value of 4.3 and at the initial uranium concentration of 800 mg/l. The kinetics of the adsorption process followed a second-order adsorption. The adsorbent used proved to be suitable for removal of uranium from aqueous solutions. 0.2 N HCl was effective in uranium desorption. The results indicated that the naturally abundant coir pith of otherwise nuisance value exhibited considerable potential for application in removal of uranium from aqueous solution.

Depositional systems and stratigraphy of Paleozoic and Lower Mesozoic rocks in outcrop, Tassili region, southwest Algeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hertig, S.P.; Tye, R.S.; Coffield, D.Q.

1991-08-01

Paleozoic to Lower Mesozoic strata of the southeastern Algerian Tassili are traditionally subdivided by regionally extensive unconformities such as the Pan African, Taconic, Caledonian, and Hercynian. Using outcrop data from southeastern Algeria, this classic approach is modified by reinterpreting the genesis of these unconformities and rock sequences. Five prominent sequences, defined within the Paleozoic and lower Mesozoic section, usually consist of a succession of lowstand, transgressive, and highstand system tracts separated by sequence boundaries or transgressive surfaces. The Pan-African, Taconic, Caledonian, and Hercynian unconformities are sequence boundaries. Important sequence boundaries also occur within the Ordovician and Silurian sections. These sequencesmore » correlate with subsurface data in the Illizi basin and provide a framework for renewed exploration in the subsurface of the Algerian Sahara, where more than 30 billion bbl of recoverable oil and oil equivalent have been generated and trapped.« less

The art of maturity modeling. Part 2. Alternative models and sensitivity analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waples, D.W.; Suizu, Masahiro; Kamata, Hiromi

1992-01-01

The sensitivity of exploration decisions to variations in several input parameters for maturity modeling was examined for the MITI Rumoi well, Hokkaido, Japan. Decisions were almost completely insensitive to uncertainties about formation age and erosional removal across some unconformities, but were more sensitive to changes in removal during unconformities which occurred near maximum paleotemperatures. Exploration decisions were not very sensitive to the choice of a particular kinetic model for hydrocarbon generation. Uncertainties in kerogen type and the kinetics of different kerogen types are more serious than differences among the various kinetic models. Results of modeling using the TTI method weremore » unsatisfactory. Thermal history and timing and amount of hydrocarbon generation estimated or calculated using the TTI method were greatly different from those obtained using a purely kinetic model. The authors strongly recommend use of the kinetic R{sub o} method instead of the TTI method. If they had lacked measured R{sub o} data, subsurface temperature data, or both, their confidence in the modeling results would have been sharply reduced. Conceptual models for predicting heat flow and thermal conductivity are simply too weak at present to allow one to carry out highly meaningful modeling unless the input is constrained by measured data. Maturity modeling therefore requires the use of more, not fewer, measured temperature and maturity data. The use of sensitivity analysis in maturity modeling is very important for understanding the geologic system, for knowing what level of confidence to place on the results, and for determining what new types of data would be most necessary to improve confidence. Sensitivity analysis can be carried out easily using a rapid, interactive maturity-modeling program.« less

Equilibrium, kinetic and thermodynamic studies of uranium biosorption by calcium alginate beads.

PubMed

Bai, Jing; Fan, Fangli; Wu, Xiaolei; Tian, Wei; Zhao, Liang; Yin, Xiaojie; Fan, Fuyou; Li, Zhan; Tian, Longlong; Wang, Yang; Qin, Zhi; Guo, Junsheng

2013-12-01

Calcium alginate beads are potential biosorbent for radionuclides removal as they contain carboxyl groups. However, until now limited information is available concerning the uptake behavior of uranium by this polymer gel, especially when sorption equilibrium, kinetics and thermodynamics are concerned. In present work, batch experiments were carried out to study the equilibrium, kinetics and thermodynamics of uranium sorption by calcium alginate beads. The effects of initial solution pH, sorbent amount, initial uranium concentration and temperature on uranium sorption were also investigated. The determined optimal conditions were: initial solution pH of 3.0, added sorbent amount of 40 mg, and uranium sorption capacity increased with increasing initial uranium concentration and temperature. Equilibrium data obtained under different temperatures were fitted better with Langmuir model than Freundlich model, uranium sorption was dominated by a monolayer way. The kinetic data can be well depicted by the pseudo-second-order kinetic model. The activation energy derived from Arrhenius equation was 30.0 kJ/mol and the sorption process had a chemical nature. Thermodynamic constants such as ΔH(0), ΔS(0) and ΔG(0) were also evaluated, results of thermodynamic study showed that the sorption process was endothermic and spontaneous. Copyright © 2013 Elsevier Ltd. All rights reserved.

Innovative mathematical modeling in environmental remediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeh, Gour T.; National Central Univ.; Univ. of Central Florida

2013-05-01

There are two different ways to model reactive transport: ad hoc and innovative reaction-based approaches. The former, such as the Kd simplification of adsorption, has been widely employed by practitioners, while the latter has been mainly used in scientific communities for elucidating mechanisms of biogeochemical transport processes. It is believed that innovative mechanistic-based models could serve as protocols for environmental remediation as well. This paper reviews the development of a mechanistically coupled fluid flow, thermal transport, hydrologic transport, and reactive biogeochemical model and example-applications to environmental remediation problems. Theoretical bases are sufficiently described. Four example problems previously carried out aremore » used to demonstrate how numerical experimentation can be used to evaluate the feasibility of different remediation approaches. The first one involved the application of a 56-species uranium tailing problem to the Melton Branch Subwatershed at Oak Ridge National Laboratory (ORNL) using the parallel version of the model. Simulations were made to demonstrate the potential mobilization of uranium and other chelating agents in the proposed waste disposal site. The second problem simulated laboratory-scale system to investigate the role of natural attenuation in potential off-site migration of uranium from uranium mill tailings after restoration. It showed inadequacy of using a single Kd even for a homogeneous medium. The third example simulated laboratory experiments involving extremely high concentrations of uranium, technetium, aluminum, nitrate, and toxic metals (e.g.,Ni, Cr, Co).The fourth example modeled microbially-mediated immobilization of uranium in an unconfined aquifer using acetate amendment in a field-scale experiment. The purposes of these modeling studies were to simulate various mechanisms of mobilization and immobilization of radioactive wastes and to illustrate how to apply reactive transport models for environmental remediation.The second problem simulated laboratory-scale system to investigate the role of natural attenuation in potential off-site migration of uranium from uranium mill tailings after restoration. It showed inadequacy of using a single Kd even for a homogeneous medium.« less

Tertiary stratigraphy and basin evolution, southern Sabah (Malaysian Borneo)

NASA Astrophysics Data System (ADS)

Balaguru, Allagu; Nichols, Gary

2004-08-01

New mapping and dating of strata in the southern part of the Central Sabah Basin in northern Borneo has made it possible to revise the lithostratigraphy and chronostratigraphy of the area. The recognition in the field of an Early Miocene regional unconformity, which may be equivalent to the Deep Regional Unconformity recognised offshore, has allowed the development of a stratigraphic framework of groups and formations, which correspond to stages in the sedimentary basin development of the area. Below the Early Miocene unconformity lies ophiolitic basement, which is overlain by an accretionary complex of Eocene age and a late Paleogene deep water succession which formed in a fore-arc basin. The late Paleogene deposits underwent syn-depositional deformation, including the development of extensive melanges, all of which can be demonstrated to lie below the unconformity in this area. Some localised limestone deposition occurred during a period of uplift and erosion in the Early Miocene, following which there was an influx of clastic sediments deposited in delta and pro-deltaic environments in the Middle Miocene. These deltaic to shallow marine deposits are now recognised as forming two coarsening-upward successions, mapped as the Tanjong and Kapilit Formations. The total thickness of these two formations in the Central Sabah Basin amounts to 6000 m, only half of the previous estimates, although the total stratigraphic thickness of Cenozoic clastic strata in Sabah may be more than 20,000 m.

A physical model for evaluating uranium nitride specific heat

NASA Astrophysics Data System (ADS)

Baranov, V. G.; Devyatko, Yu. N.; Tenishev, A. V.; Khlunov, A. V.; Khomyakov, O. V.

2013-03-01

Nitride fuel is one of perspective materials for the nuclear industry. But unlike the oxide and carbide uranium and mixed uranium-plutonium fuel, the nitride fuel is less studied. The present article is devoted to the development of a model for calculating UN specific heat on the basis of phonon spectrum data within the solid state theory.

US Transuranium and Uranium Registries case study on accidental exposure to uranium hexafluoride.

PubMed

Avtandilashvili, Maia; Puncher, Matthew; McComish, Stacey L; Tolmachev, Sergei Y

2015-03-01

The United States Transuranium and Uranium Registries' (USTUR) whole-body donor (Case 1031) was exposed to an acute inhalation of uranium hexafluoride (UF6) produced from an explosion at a uranium processing plant 65 years prior to his death. The USTUR measurements of tissue samples collected at the autopsy indicated long-term retention of inhaled slightly enriched uranium material (0.85% (235)U) in the deep lungs and thoracic lymph nodes. In the present study, the authors combined the tissue measurement results with historical bioassay data, and analysed them with International Commission on Radiological Protection (ICRP) respiratory tract models and the ICRP Publication 69 systemic model for uranium using maximum likelihood and Bayesian statistical methods. The purpose of the analysis was to estimate intakes and model parameter values that best describe the data, and evaluate their effect on dose assessment. The maximum likelihood analysis, which used the ICRP Publication 66 human respiratory tract model, resulted in a point estimate of 79 mg of uranium for the occupational intake composed of 86% soluble, type F material and 14% insoluble, type S material. For the Bayesian approach, the authors applied the Markov Chain Monte Carlo method, but this time used the revised human respiratory tract model, which is currently being used by ICRP to calculate new dose coefficients for workers. The Bayesian analysis estimated that the mean uranium intake was 160 mg, and calculated the case-specific lung dissolution parameters with their associated uncertainties. The parameters were consistent with the inhaled uranium material being predominantly soluble with a small but significant insoluble component. The 95% posterior range of the rapid dissolution fraction (the fraction of deposited material that is absorbed to blood rapidly) was 0.12 to 0.91 with a median of 0.37. The remaining fraction was absorbed slowly, with a 95% range of 0.000 22 d(-1) to 0.000 36 d(-1) and a median of 0.000 31 d(-1). The effective dose per unit intake calculated using the dissolution parameters derived from the maximum likelihood and the Bayesian analyses was higher than the current ICRP dose coefficient for type F uranium by a factor of 2 or 7, respectively; the higher value of the latter was due to use of the revised respiratory tract model. The dissolution parameter values obtained here may be more appropriate to use for radiation protection purposes when individuals are exposed to a UF6 mixture that contains an insoluble uranium component.

Thermodynamic properties of selected uranium compounds and aqueous species at 298.15 K and 1 bar and at higher temperatures; preliminary models for the origin of coffinite deposits

USGS Publications Warehouse

Hemingway, B.S.

1982-01-01

Thermodynamic values for 110 uranium-bearing phases and 28 aqueous uranium solution species (298.15 K and l bar) are tabulated based upon evaluated experimental data (largely from calorimetric experiments) and estimated values. Molar volume data are given for most of the solid phases. Thermodynamic values for 16 uranium-bearing phases are presented for higher temperatures in the form of and as a supplement to U.S. Geological Survey Bulletin 1452 (Robie et al., 1979). The internal consistency of the thermodynamic values reported herein is dependent upon the reliability of the experimental results for several uranium phases that have been used as secondary calorimetric reference phases. The data for the reference phases and for those phases evaluated with respect to the secondary reference phases are discussed. A preliminary model for coffinite formation has been proposed together with an estimate of the free energy of formation of coffinite. Free energy values are estimated for several other uranium-bearing silicate phases that have been reported as secondary uranium phases associated with uranium ore deposits and that could be expected to develop wherever uranium is leached by groundwaters.

Enhanced uranium immobilization and reduction by Geobacter sulfurreducens biofilms.

PubMed

Cologgi, Dena L; Speers, Allison M; Bullard, Blair A; Kelly, Shelly D; Reguera, Gemma

2014-11-01

Biofilms formed by dissimilatory metal reducers are of interest to develop permeable biobarriers for the immobilization of soluble contaminants such as uranium. Here we show that biofilms of the model uranium-reducing bacterium Geobacter sulfurreducens immobilized substantially more U(VI) than planktonic cells and did so for longer periods of time, reductively precipitating it to a mononuclear U(IV) phase involving carbon ligands. The biofilms also tolerated high and otherwise toxic concentrations (up to 5 mM) of uranium, consistent with a respiratory strategy that also protected the cells from uranium toxicity. The enhanced ability of the biofilms to immobilize uranium correlated only partially with the biofilm biomass and thickness and depended greatly on the area of the biofilm exposed to the soluble contaminant. In contrast, uranium reduction depended on the expression of Geobacter conductive pili and, to a lesser extent, on the presence of the c cytochrome OmcZ in the biofilm matrix. The results support a model in which the electroactive biofilm matrix immobilizes and reduces the uranium in the top stratum. This mechanism prevents the permeation and mineralization of uranium in the cell envelope, thereby preserving essential cellular functions and enhancing the catalytic capacity of Geobacter cells to reduce uranium. Hence, the biofilms provide cells with a physically and chemically protected environment for the sustained immobilization and reduction of uranium that is of interest for the development of improved strategies for the in situ bioremediation of environments impacted by uranium contamination. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

Enhanced Uranium Immobilization and Reduction by Geobacter sulfurreducens Biofilms

PubMed Central

Cologgi, Dena L.; Speers, Allison M.; Bullard, Blair A.; Kelly, Shelly D.

2014-01-01

Biofilms formed by dissimilatory metal reducers are of interest to develop permeable biobarriers for the immobilization of soluble contaminants such as uranium. Here we show that biofilms of the model uranium-reducing bacterium Geobacter sulfurreducens immobilized substantially more U(VI) than planktonic cells and did so for longer periods of time, reductively precipitating it to a mononuclear U(IV) phase involving carbon ligands. The biofilms also tolerated high and otherwise toxic concentrations (up to 5 mM) of uranium, consistent with a respiratory strategy that also protected the cells from uranium toxicity. The enhanced ability of the biofilms to immobilize uranium correlated only partially with the biofilm biomass and thickness and depended greatly on the area of the biofilm exposed to the soluble contaminant. In contrast, uranium reduction depended on the expression of Geobacter conductive pili and, to a lesser extent, on the presence of the c cytochrome OmcZ in the biofilm matrix. The results support a model in which the electroactive biofilm matrix immobilizes and reduces the uranium in the top stratum. This mechanism prevents the permeation and mineralization of uranium in the cell envelope, thereby preserving essential cellular functions and enhancing the catalytic capacity of Geobacter cells to reduce uranium. Hence, the biofilms provide cells with a physically and chemically protected environment for the sustained immobilization and reduction of uranium that is of interest for the development of improved strategies for the in situ bioremediation of environments impacted by uranium contamination. PMID:25128347

Metal-rich fluid inclusions provide new insights into unconformity-related U deposits (Athabasca Basin and Basement, Canada)

NASA Astrophysics Data System (ADS)

Richard, Antonin; Cathelineau, Michel; Boiron, Marie-Christine; Mercadier, Julien; Banks, David A.; Cuney, Michel

2016-02-01

The Paleoproterozoic Athabasca Basin (Canada) hosts numerous giant unconformity-related uranium deposits. The scope of this study is to establish the pressure, temperature, and composition (P-T-X conditions) of the brines that circulated at the base of the Athabasca Basin and in its crystalline basement before, during and after UO2 deposition. These brines are commonly sampled as fluid inclusions in quartz- and dolomite-cementing veins and breccias associated with alteration and U mineralization. Microthermometry and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) data from five deposits (Rabbit Lake, P-Patch, Eagle Point, Millennium, and Shea Creek) complement previously published data for the McArthur River deposit. In all of the deposits investigated, fluid inclusion salinity is between 25 and 40 wt.% NaCl equiv., with compositions displaying a continuum between a "NaCl-rich brine" end-member (Cl > Na > Ca > Mg > K) and a "CaCl2-rich brine" end-member (Cl > Ca ≈ Mg > Na > K). The CaCl2-rich brine has the highest salinity and shows evidence for halite saturation at the time of trapping. The continuum of compositions between the NaCl-rich brine and the CaCl2-rich brine end-members combined with P-T reconstructions suggest anisothermal mixing of the two brines (NaCl-rich brine, 180 ± 30 °C and 800 ± 400 bars; CaCl2-rich brine, 120 ± 30 °C and 600 ± 300 bars) that occurred under fluctuating pressure conditions (hydrostatic to supra-hydrostatic). However, because the two brines were U bearing and therefore oxidized, brine mixing was probably not the driving force for UO2 deposition. Several scenarios are put forward to account for the Cl-Na-Ca-Mg-K composition of the brines, involving combinations of seawater evaporation, halite dissolution, mixing with a halite-dissolution brine, Mg/Ca exchange by dolomitization, Na/Ca exchange by albitization of plagioclase, Na/K exchange by albitization of K-feldspar, and Mg loss by Mg-rich alteration. Finally, the metal concentrations in the NaCl-rich and CaCl2-rich brines are among the highest recorded compared to present-day sedimentary formation waters and fluid inclusions from basin-hosted base metal deposits (up to 600 ppm U, 3000 ppm Mn, 4000 ppm Zn, 6000 ppm Cu, 8000 ppm Pb, and 10,000 ppm Fe). The CaCl2-rich brine carries up to one order of magnitude more metal than the NaCl-rich brine. Though the exact origin of major cations and metals of the two brines remains uncertain, their contrasting compositions indicate that the two brines had distinct flow paths and fluid-rock interactions. Large-scale circulation of the brines in the Athabasca Basin and Basement was therefore a key parameter for metal mobility (including U) and formation of unconformity-related U deposits.

Uranium levels in the diet of São Paulo City residents.

PubMed

Garcia, F; Barioni, A; Arruda-Neto, J D T; Deppman, A; Milian, F; Mesa, J; Rodriguez, O

2006-07-01

Natural levels of uranium in the diet of São Paulo City residents were studied, and radionuclide concentrations were measured by the fission track method on samples of typical adult food items. This information was used to evaluate the daily intake of uranium in individuals living in São Paulo City which is, according to our findings, around 0.97 microg U/day. Using the ICRP Uranium-model, we estimated the uranium accumulation and committed doses in some tissues and organs, as function of time. We compared the output of the ICRP uranium biokinetic model, tailored for the conditions prevailing in São Paulo, with experimental data from other localities. Such comparison was possible by means of a simple method we developed, which allows normalization among experimental results from different regions where distinct values of chronic daily intake are observed.

The Impact of Mass Movement and Fluid Flow during Ridge Subduction inferred from Physical Properties and Zeolite Assemblage in the Upper Plate Slope of the Costa Rica Subduction Zone

NASA Astrophysics Data System (ADS)

Hamahashi, M.; Screaton, E.; Tanikawa, W.; Hashimoto, Y.; Martin, K. M.; Saito, S.; Kimura, G.

2015-12-01

The Costa Rica subduction zone offshore Osa Peninsula is known as an erosive margin with active seismicity and the subduction of the Cocos Ridge. One of the major unknowns in this margin is the nature of the unconformity at the base of the slope sediments in the upper plate and the high velocity materials below. To investigate the geologic processes across the unconformity, we examined the consolidation state and mineral assemblages of the sediments at the mid-slope Site 1380 drilled during IODP Expedition 344 by conducting microstructural observation, particle size analysis, X-ray fluorescence/diffraction analysis and resistivity measurement. The general compaction trend is controlled primarily by grain-size sorting and the physical property transition is likely caused by massive sediment removal under normal fault regime, thickness of which range between ~600-850 m determined from the composite porosity-depth curve. Across the unconformity between the late Pliocene~late Pleistocene silty clay (Unit 1) and late Pliocene~early Pleistocene clayey siltstone (Unit 2), the mineral/element components of the sediments is marked by the transitions in zeolite compositions; Unit 1 consists of laumontite and heulandite, whereas below the unconformity, Unit 2 sediments contain analcime, laumontite, and heulandite, but laumontite become less abundant at lower depth. The experienced temperature of the sediments in Unit 2 is estimated to have reached between ~86 and 122℃ as inferred from analcime burial diagenesis. This may correspond with the greater depth range prior to mass movement and normal faulting. The initial analcime burial diagenetic zone was likely cut off by the sediment removal across the unconformity, and later overprinted by high temperature fluid along the boundary forming laumontite and heulandite in the vicinity. These results illustrate that ridge subduction has substantial potential to cause mass movement, an extensional stress regime, and fluid flow from depth.

Early Mesozoic history and petroleum potential of formations in Wyoming and northern Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Picard, M.D.

1993-08-01

During the Triassic and Jurassic, over what is now Wyoming and northern Utah, roughly equal amounts of sediment were being deposited in continental settings-lake, stream, and eolian-and in shallow-marine or deltaic-plain settings-delta, beach, marsh, tidal flat, and shallow shelf. Clastic rocks dominate. In order of decreasing abundance, the rocks are fine-grained clastics (siltstone, claystone, mudstone), sandstone, carbonates, evaporites, and claystone- and carbonate-pebble conglomerate. Approximately four-fifths of the succession contains red beds or variegated layers-purple, maroon, lavender, olive, green. Unconformities bound Jurassic formations in Wyoming-Nugget, Gypsum Spring, Sundance, and Morrison. Unconformities also bound the continental Upper Triassic section-unnamed red bed unit,more » Jelm, Popo Agie-separating it from the underlying shallow-marine formations-Dinwoody, Red Peak, Alcova, Crow Mountain. Within the marine sequence, an unconformity occurs at the top of the Alcova and, quite likely, shorter periods of erosion took place at the top and below the base of the sandy faces that underlies the Alcova. The postulate duration of the principal unconformities totals about 18 m.y., at least one-sixth of early Mesozoic time. The bulk of the remaining 80-100 m.y. may be represented by a large number of smaller unconformities. For the lower Mesozoic, as for most stratigraphic intervals, a few beds contain the story of what has taken place during the abyss of geologic time. Like other places in the world where evaporites occur in the Triassic, the Wyoming section produces little crude oil. No significant sequence in the early Mesozoic shows source-bed characteristics. The Crow Mountain Sandstone contains the best reservoirs. The Lower( ) Jurassic Nugget Sandstone produces the most oil and gas in the thrust belt of southwestern Wyoming and northern Utah. Cretaceous claystones below the thrusts contain the source beds.« less

Investigation of a Major Stratigraphic Unconformity with the Curiosity Rover

NASA Astrophysics Data System (ADS)

Lewis, K. W.; Grotzinger, J. P.; Gupta, S.; Rubin, D. M.

2015-12-01

Since its departure from the plains of Aeolis Palus, the Curiosity rover has traversed through a number of new geologic units at the base of Mount Sharp in Gale crater. These have included both units inferred to comprise the lower strata of Mount Sharp itself, along with units that appear to superpose Mount Sharp. Over the last 100 sols, Curiosity has documented several occurrences of a stratigraphic contact between fine-grained mudstones of the Murray Formation, and coarser sandstones of the overlying Stimson Unit. Detailed mapping from both orbital and rover image and topographic data suggests an unconformable relationship between the two units. From orbit, inferred exposures of the unconformity span at least several tens of meters, climbing up the lowermost slopes of Mount Sharp. Although the absolute timing of the two units is poorly constrained, this unconformity between likely represents a geologically significant gap in time. Deposition of the overlying Stimson Unit is inferred to post-date the large-scale erosion of Mount Sharp, likely requiring late stage aqueous interaction in the lithification of the Stimson Unit. From the rover, stereo imaging reveals the small-scale topography preserved at the Murray-Stimson contact, and allows the determination of bedding geometries within the units. Where laminations are expressed, the basal Mount Sharp rocks exhibit planar stratification at low angles to horizontal. In contrast, the coarser-grained Stimson Unit exhibits large-scale cross stratification. Three dimensional bedding geometry within this unit indicates a predominant southward transport direction uphill towards Mount Sharp. The observation of rounded calcium sulfate clasts in the lowermost Stimson Unit, interpreted to be reworked veins from the underlying Murray formation, supports the interpretation of an erosional unconformity. Investigations at the boundary between these two distinct units present a unique opportunity to probe the long-term environmental history of the Gale crater basin.

Experiments in anodic film effects during electrorefining of scrap U-10Mo fuels in support of modeling efforts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Kleeck, M.; Chemical Sciences and Engineering Division, Argonne National Laboratory, Argonne, IL 60439; Willit, J.

A monolithic uranium molybdenum alloy clad in zirconium has been proposed as a low enriched uranium (LEU) fuel option for research and test reactors, as part of the Reduced Enrichment for Research and Test Reactors program. Scrap from the fuel's manufacture will contain a significant portion of recoverable LEU. Pyroprocessing has been identified as an option to perform this recovery. A model of a pyroprocessing recovery procedure has been developed to assist in refining the LEU recovery process and designing the facility. Corrosion theory and a two mechanism transport model were implemented on a Mat-Lab platform to perform the modeling.more » In developing this model, improved anodic behavior prediction became necessary since a dense uranium-rich salt film was observed at the anode surface during electrorefining experiments. Experiments were conducted on uranium metal to determine the film's character and the conditions under which it forms. The electro-refiner salt used in all the experiments was eutectic LiCl/KCl containing UCl{sub 3}. The anodic film material was analyzed with ICP-OES to determine its composition. Both cyclic voltammetry and potentiodynamic scans were conducted at operating temperatures between 475 and 575 C. degrees to interrogate the electrochemical behavior of the uranium. The results show that an anodic film was produced on the uranium electrode. The film initially passivated the surface of the uranium on the working electrode. At high over potentials after a trans-passive region, the current observed was nearly equal to the current observed at the initial active level. Analytical results support the presence of K{sub 2}UCl{sub 6} at the uranium surface, within the error of the analytical method.« less

Column Testing and 1D Reactive Transport Modeling to Evaluate Uranium Plume Persistence Processes

NASA Astrophysics Data System (ADS)

Johnson, R. H.; Morrison, S.; Morris, S.; Tigar, A.; Dam, W. L.; Dayvault, J.

2015-12-01

At many U.S. Department of Energy Office of Legacy Management sites, 100 year natural flushing was selected as a remedial option for groundwater uranium plumes. However, current data indicate that natural flushing is not occurring as quickly as expected and solid-phase and aqueous uranium concentrations are persistent. At the Grand Junction, Colorado office site, column testing was completed on core collected below an area where uranium mill tailings have been removed. The total uranium concentration in this core was 13.2 mg/kg and the column was flushed with laboratory-created water with no uranium and chemistry similar to the nearby Gunnison River. The core was flushed for a total of 91 pore volumes producing a maximum effluent uranium concentration of 6,110 μg/L at 2.1 pore volumes and a minimum uranium concentration of 36.2 μg/L at the final pore volume. These results indicate complex geochemical reactions at small pore volumes and a long tailing affect at greater pore volumes. Stop flow data indicate the occurrence of non-equilibrium processes that create uranium concentration rebound. These data confirm the potential for plume persistence, which is occurring at the field scale. 1D reactive transport modeling was completed using PHREEQC (geochemical model) and calibrated to the column test data manually and using PEST (inverse modeling calibration routine). Processes of sorption, dual porosity with diffusion, mineral dissolution, dispersion, and cation exchange were evaluated separately and in combination. The calibration results indicate that sorption and dual porosity are major processes in explaining the column test data. These processes are also supported by fission track photographs that show solid-phase uranium residing in less mobile pore spaces. These procedures provide valuable information on plume persistence and secondary source processes that may be used to better inform and evaluate remedial strategies, including natural flushing.

Modeling and experimental examination of water level effects on radon exhalation from fragmented uranium ore.

PubMed

Ye, Yong-Jun; Dai, Xin-Tao; Ding, De-Xin; Zhao, Ya-Li

2016-12-01

In this study, a one-dimensional steady-state mathematical model of radon transport in fragmented uranium ore was established according to Fick's law and radon transfer theory in an air-water interface. The model was utilized to obtain an analytical solution for radon concentration in the air-water, two-phase system under steady state conditions, as well as a corresponding radon exhalation rate calculation formula. We also designed a one-dimensional experimental apparatus for simulating radon diffusion migration in the uranium ore with various water levels to verify the mathematical model. The predicted results were in close agreement with the measured results, suggesting that the proposed model can be readily used to determine radon concentrations and exhalation rates in fragmented uranium ore with varying water levels. Copyright © 2016. Published by Elsevier Ltd.

Precambrian uranium-bearing quartz-pebble conglomerates: exploration model and United States resource potential

DOE Office of Scientific and Technical Information (OSTI.GOV)

Houston, R.S.; Karlstrom, K.E.

1979-11-01

Uranium has been discovered in fluvial quartz-pebble conglomerates in most of the Precambrian shield areas of the world, including the Canadian, African, South American, Indian, Baltic, and Australian shields. Occurrences in these and other areas are shown. Two of these occurrences, the Huronian supergroup of Canada and the Witwatersrand deposit of South Africa contain 20 to 30 percent of the planet's known uranium reserves. Thus it is critical that we understand the origin of these deposits and develop exploration models that can aid in finding new deposits. Inasmuch as these uranium-bearing conglomerates are confined almost entirely to rocks of Precambrianmore » age, Part I of this review begins with a discussion of Precambrian geology as it applies to the conglomerates. This is followed by a discussion of genetic concepts, a discussion of unresolved problems, and finally a suggested exploration model. Part II summarizes known and potential occurrences of Precambrian fossil placers in the world and evaluates them in terms of the suggested exploration model. Part III discusses the potential for important Precambrian fossil-placer uranium deposits in the United States and includes suggestions that may be helpful in establishing an exploration program in this country. Part III also brings together new (1975-1978) data on uranium occurrences in the Precambrian of the Wyoming Province. Part IV is a complete bibliography of Precambrian fossil placers, divided according to geographical areas. In total, this paper is designed to be a comprehensive review of Precambrian uranium-bearing fossil placers which will be of use to uranium explorationists and to students of Precambrian geology.« less

Stratigraphy of Aeolis Dorsa, Mars: Stratigraphic context of the great river deposits

NASA Astrophysics Data System (ADS)

Kite, Edwin S.; Howard, Alan D.; Lucas, Antoine S.; Armstrong, John C.; Aharonson, Oded; Lamb, Michael P.

2015-06-01

Unraveling the stratigraphic record is the key to understanding ancient climate and past climate changes on Mars (Grotzinger, J. et al. [2011]. Astrobiology 11, 77-87). Stratigraphic records of river deposits hold particular promise because rain or snowmelt must exceed infiltration plus evaporation to allow sediment transport by rivers. Therefore, river deposits when placed in stratigraphic order could constrain the number, magnitudes, and durations of the wettest (and presumably most habitable) climates in Mars history. We use crosscutting relationships to establish the stratigraphic context of river and alluvial-fan deposits in the Aeolis Dorsa sedimentary basin, 10°E of Gale crater. At Aeolis Dorsa, wind erosion has exhumed a stratigraphic section of sedimentary rocks consisting of at least four unconformity-bounded rock packages, recording three or more distinct episodes of surface runoff. Early deposits (>700 m thick) are embayed by river deposits (>400 m thick), which are in turn unconformably draped by fan-shaped deposits (<100 m thick) which we interpret as alluvial fans. Yardang-forming layered deposits (>900 m thick) unconformably drape all previous deposits. River deposits embay a dissected landscape formed of sedimentary rock. The river deposits are eroding out of at least two distinguishable units. There is evidence for pulses of erosion during the interval of river deposition. The total interval spanned by river deposits is >(1 × 106-2 × 107) yr, and this is extended if we include alluvial-fan deposits. Alluvial-fan deposits unconformably postdate thrust faults which crosscut the river deposits. This relationship suggests a relatively dry interval of >4 × 107 yr after the river deposits formed and before the fan-shaped deposits formed, based on probability arguments. Yardang-forming layered deposits unconformably postdate all of the earlier deposits. They contain rhythmite and their induration suggests a damp or wet (near-) surface environment. The time gap between the end of river deposition and the onset of yardang-forming layered deposits is constrained to >1 × 108 yr by the high density of impact craters embedded at the unconformity. The time gap between the end of alluvial-fan deposition and the onset of yardang-forming layered deposits was at least long enough for wind-induced saltation abrasion to erode 20-30 m into the alluvial-fan deposits. We correlate the yardang-forming layered deposits to the upper layers of Gale crater's mound (Mt. Sharp/Aeolis Mons), and the fan-shaped deposits to Peace Vallis fan in Gale crater. Alternations between periods of low mean obliquity and periods of high mean obliquity may have modulated erosion-deposition cycling in Aeolis. This is consistent with the results from an ensemble of simulations of Solar System orbital evolution and the resulting history of the obliquity of Mars. 57 of our 61 simulations produce one or more intervals of continuously low mean Mars obliquity that are long enough to match our Aeolis Dorsa unconformity data.

Investigation of uranium binding forms in selected German mineral waters.

PubMed

Osman, Alfatih A A; Geipel, Gerhard; Bernhard, Gert; Worch, Eckhard

2013-12-01

Cryogenic time-resolved laser-induced fluorescence spectroscopy was successfully used to identify uranium binding forms in selected German mineral waters of extremely low uranium concentrations (<2.0 μg/L). The measurements were performed at a low temperature of 153 K. The spectroscopic data showed a prevalence of aquatic species Ca2UO2(CO3)3 in all investigated waters, while other uranyl-carbonate complexes, viz, UO2CO3(aq) and UO2(CO3)2 (2-), only existed as minor species. The pH value, alkalinity (CO3 (2-)), and the main water inorganic constituents, specifically the Ca(2+) concentration, showed a clear influence on uranium speciation. Speciation modeling was performed using the most recent thermodynamic data for aqueous complexes of uranium. The modeling results for the main uranium binding form in the investigated waters indicated a good agreement with the spectroscopy measurements.

Lattice constant in nonstoichiometric uranium dioxide from first principles

NASA Astrophysics Data System (ADS)

Bruneval, Fabien; Freyss, Michel; Crocombette, Jean-Paul

2018-02-01

Nonstoichiometric uranium dioxide experiences a shrinkage of its lattice constant with increasing oxygen content, in both the hypostoichiometric and the hyperstoichiometric regimes. Based on first-principles calculations within the density functional theory (DFT)+U approximation, we have developed a point defect model that accounts for the volume of relaxation of the most significant intrinsic defects of UO2. Our point defect model takes special care of the treatment of the charged defects in the equilibration of the model and in the determination of reliable defect volumes of formation. In the hypostoichiometric regime, the oxygen vacancies are dominant and explain the lattice constant variation with their surprisingly positive volume of relaxation. In the hyperstoichiometric regime, the uranium vacancies are predicted to be the dominating defect,in contradiction with experimental observations. However, disregarding uranium vacancies allows us to recover a good match for the lattice-constant variation as a function of stoichiometry. This can be considered a clue that the uranium vacancies are indeed absent in UO2 +x, possibly due to the very slow diffusion of uranium.

Uraniferous opal, Virgin Valley, Nevada: conditions of formation and implications for uranium exploration

USGS Publications Warehouse

Zielinski, R.A.

1982-01-01

Uraniferous, fluorescent opal, which occurs in tuffaceous sedimentary rocks at Virgin Valley, Nevada, records the temperature and composition of uranium-rich solutions as well as the time of uranium-silica coprecipitation. Results are integrated with previous geologic and geochronologic data for the area to produce a model for uranium mobility that may be used to explore for uranium deposits in similar geologic settings. Uraniferous opal occurs as replacements of diatomite, or silicic air-fall ash layers in tuffaceous lakebeds of the Virgin Valley Formation (Miocene) of Merriam (1907). Fission-track radiography shows uranium to be homogeneously dispersed throughout the opal structure, suggesting coprecipitation of dissolved uranium and silica gel. Fluid inclusions preserved within opal replacements of diatomite have homogenization temperatures in the epithermal range and are of low salinity. Four samples of opal from one locality all have U-Pb apparent ages which suggest uraniferous opal precipitation in late Pliocene time. These ages correspond to a period of local, normal faulting, and highangle faults may have served as vertical conduits for transport of deep, thermalized ground water to shallower levels. Lateral migration of rising solutions occurred at intersections of faults with permeable strata. Silica and some uranium were dissolved from silica-rich host strata of 5-20 ppm original uranium content and reprecipitated as the solutions cooled. The model predicts that in similar geologic settings, ore-grade concentrations of uranium will occur in permeable strata that intersect high-angle faults and that contain uranium source rocks as well as efficient reductant traps for uranium. In the absence of sufficient quantities of reductant materials, uranium will be flushed from the system or will accumulate in low-grade disseminated hosts such as uraniferous opal. ?? 1982.

Nuclear fuel requirements for the American economy - A model

NASA Astrophysics Data System (ADS)

Curtis, Thomas Dexter

A model is provided to determine the amounts of various fuel streams required to supply energy from planned and projected nuclear plant operations, including new builds. Flexible, user-defined scenarios can be constructed with respect to energy requirements, choices of reactors and choices of fuels. The model includes interactive effects and extends through 2099. Outputs include energy provided by reactors, the number of reactors, and masses of natural Uranium and other fuels used. Energy demand, including electricity and hydrogen, is obtained from US DOE historical data and projections, along with other studies of potential hydrogen demand. An option to include other energy demand to nuclear power is included. Reactor types modeled include (thermal reactors) PWRs, BWRs and MHRs and (fast reactors) GFRs and SFRs. The MHRs (VHTRs), GFRs and SFRs are similar to those described in the 2002 DOE "Roadmap for Generation IV Nuclear Energy Systems." Fuel source choices include natural Uranium, self-recycled spent fuel, Plutonium from breeder reactors and existing stockpiles of surplus HEU, military Plutonium, LWR spent fuel and depleted Uranium. Other reactors and fuel sources can be added to the model. Fidelity checks of the model's results indicate good agreement with historical Uranium use and number of reactors, and with DOE projections. The model supports conclusions that substantial use of natural Uranium will likely continue to the end of the 21st century, though legacy spent fuel and depleted uranium could easily supply all nuclear energy demand by shifting to predominant use of fast reactors.

Stratigraphic relations and U-Pb geochronology of the Upper Cretaceous upper McCoy Mountains Formation, southwestern Arizona

USGS Publications Warehouse

Tosdal, R.M.; Stone, P.

1994-01-01

A previously unrecognized angular unconformity divides the Jurassic and Cretaceous McCoy Mountains Formation into a lower and an upper unit in the Dome Rock Mountains and Livingston Hills of western Arizona. The intraformation unconformity in the McCoy Mountains Formation developed where rocks of the lower unit were deformed adjacent to the southern margin of the Maria fold and thrust belt. The upper unit of the formation is interpreted as a foreland-basin deposit that was shed southward from the actively rising and deforming fold and thrust belt. The apparent absence of an equivalent unconformity in the McCoy Mountains Formation in adjacent California is presumably a consequence of the observed westward divergence of the outcrop belt from the fold and thrust belt. Tectonic burial beneath the north-vergent Mule Mountains thrust system in the latest Late Cretaceous (~70 Ma) marked the end of Mesozoic contractile deformation in the area. -from Authors

Modelling land use/cover changes with markov-cellular automata in Komering Watershed, South Sumatera

NASA Astrophysics Data System (ADS)

Kusratmoko, E.; Albertus, S. D. Y.; Supriatna

2017-01-01

This research has a purpose to study and develop a model that can representing and simulating spatial distribution pattern of land use change in Komering watershed. The Komering watershed is one of nine sub Musi river basin and is located in the southern part of Sumatra island that has an area of 8060,62 km2. Land use change simulations, achieved through Markov-cellular automata (CA) methodologies. Slope, elevation, distance from road, distance from river, distance from capital sub-district, distance from settlement area area were driving factors that used in this research. Land use prediction result in 2030 also shows decrease of forest acreage up to -3.37%, agricultural land decreased up to -2.13%, and open land decreased up to -0.13%. On the other hand settlement area increased up to 0.07%, and plantation land increased up to 5.56%. Based on the predictive result, land use unconformity percentage to RTRW in Komering watershed is 18.62 % and land use conformity is 58.27%. Based on the results of the scenario, where forest in protected areas and agriculture land are maintained, shows increase the land use conformity amounted to 60.41 % and reduce unconformity that occur in Komering watershed to 17.23 %.

Major variation of paleo-maximum temperature and consolidation state within post Miocene forearc basin, central Japan

NASA Astrophysics Data System (ADS)

Kamiya, N.; Yamamoto, Y.; Takemura, T.

2015-12-01

Since forearc-basin evolve associated with development of the accretionary prisms, their geologic structures have clues to understanding the tectonic processes associated with plate subduction. We found a major difference in paleo-geothermal structure and consolidation states between the unconformity in the forearc basin in the Boso Peninsula, central Japan. The geology of the Boso Peninsula, central Japan is divided into three parts; Early Miocene and Late Miocene accretionary prisms in the southern part, the Hayama-Mineoka tectonic belt mainly composed of ophiolite in the middle part, and post-Middle Miocene forearc basin in the northern part. Sediments in the forearc basin are composed of 15-3Ma Miura Group and 3-0.6Ma Kazusa Group. Boundary of the two groups is the Kurotaki Unconformity formed about 3Ma, when convergent direction of the Philippine Sea Plate has been changed (Takahashi, 2006). Vitrinite reflectance (Ro) analyses were conducted and revealed that major variation of paleo-maximum temperature between the Miura and Kazusa groups. The maximum paleo-temperature in the Miura Group is estimated as 70-95˚C, whereas in the lower part of the Kazusa Group is less than 10-35˚C. Given 20˚C/km (Sakai et al, 2011) paleo-geothermal gradient, approximately 2000 m uplifting/erosion of the Miura Group is expected when the unconformity formed. To verify the amount of this uplifting/erosion, we are performing consolidation test of mudstone. [Reference] Takahashi, M., 2006, Tectonic Development of the Japanese Islands Controlled by Philippine Sea Plate Motion, Journal of Geography, 115, 116-123. Sakai R., Munakata M., Kimura H., Ichikawa Y., and Nakamura M., 2011, Study on Validation Method of Regional Groundwater Flow Model : Case Study for Boso Peninsula, JAEA-research 2010(66), 1-20, 1-2.

Composition and stable-isotope geochemistry of natural gases from Kansas, Midcontinent, U.S.A.

USGS Publications Warehouse

Jenden, P.D.; Newell, K.D.; Kaplan, I.R.; Watney, W.L.

1988-01-01

More than 28??1012 ft.3 (79??1010 m3) of natural gas and 5.3??109 bbl (8.4??108 m3) of oil have been produced in Kansas, U.S.A., from Paleozoic carbonate and sandstone reservoirs on structural uplifts and shallow embayments along the northern margin of the Anadarko basin. A heavily-explored, geologically well-characterized state, Kansas is an excellent place to study hydrocarbon migration and to test geochemical models for the origin of natural gases. Immature to marginally-mature rocks of eastern Kansas (Cherokee and Forest City basins) produce mixed microbial and thermogenic gases. Gases in this region have wetness = 0.03-51%, methane ??13C = -65 to -43??? and methane ??D = -260 to -150???. Gases from central and western Kansas (Nemaha uplift to Hugoton embayment) are entirely thermogenic and have wetness =4-51%, methane ??13C = -48 to -39??? and methane ??D = -195 to -140???. Ethane and propane ??13C-values throughout Kansas vary from -38 to -28??? and from -35 to -24???, respectively. Mature thermogenic gas (generated from source rocks in southwestern Kansas and the Anadarko basin with 1.0% ??? Ro ??? 1.4%) is recognized throughout the state. Lateral migration into shallow reservoirs on the Central Kansas and northern Nemaha uplifts and in the Cherokee basin probably occurred along basal Pennsylvanian conglomerates and weathered Lower Paleozoic carbonates at the regional sub-Pennsylvanian unconformity. Early thermogenic gas (generated by local source rocks with Ro ??? 0.7%) is recognized in isolated fields in the Salina and Forest City basins, in Ordovician reservoirs beneath the sub-Pennsylvanian unconformity in the Cherokee basin, and in reservoirs generally above the unconformity in the Cherokee and Sedgwick basins, the eastern Central Kansas uplift and the Hugoton embayment. ?? 1988.

Kinetic study of the thermal decomposition of uranium metaphosphate, U(PO3)4, into uranium pyrophosphate, UP2O7

NASA Astrophysics Data System (ADS)

Yang, Hee-Chul; Kim, Hyung-Ju; Lee, Si-Young; Yang, In-Hwan; Chung, Dong-Yong

2017-06-01

The thermochemical properties of uranium compounds have attracted much interest in relation to thermochemical treatments and the safe disposal of radioactive waste bearing uranium compounds. The characteristics of the thermal decomposition of uranium metaphosphate, U(PO3)4, into uranium pyrophosphate, UP2O7, have been studied from the view point of reaction kinetics and acting mechanisms. A mixture of U(PO3)4 and UP2O7 was prepared from the pyrolysis residue of uranium-bearing spent TBP. A kinetic analysis of the reaction of U(PO3)4 into UP2O7 was conducted using an isoconversional method and a master plot method on the basis of data from a non-isothermal thermogravimetric analysis. The thermal decomposition of U(PO3)4 into UP2O7 followed a single-step reaction with an activation energy of 175.29 ± 1.58 kJ mol-1. The most probable kinetic model was determined as a type of nucleation and nuclei-growth models, the Avrami-Erofeev model (A3), which describes that there are certain restrictions on nuclei growth of UP2O7 during the solid-state decomposition of U(PO3)4.

Cambrian Sauk transgression in the Grand Canyon region redefined by detrital zircons

NASA Astrophysics Data System (ADS)

Karlstrom, Karl; Hagadorn, James; Gehrels, George; Matthews, William; Schmitz, Mark; Madronich, Lauren; Mulder, Jacob; Pecha, Mark; Giesler, Dominique; Crossey, Laura

2018-06-01

The Sauk transgression was one of the most dramatic global marine transgressions in Earth history. It is recorded by deposition of predominantly Cambrian non-marine to shallow marine sheet sandstones unconformably above basement rocks far into the interiors of many continents. Here we use dating of detrital zircons sampled from above and below the Great Unconformity in the Grand Canyon region to bracket the timing of the Sauk transgression at this classic location. We find that the Sixtymile Formation, long considered a Precambrian unit beneath the Great Unconformity, has maximum depositional ages that get younger up-section from 527 to 509 million years old. The unit contains angular unconformities and soft-sediment deformation that record a previously unknown period of intracratonic faulting and epeirogeny spanning four Cambrian stages. The overlying Tapeats Sandstone has youngest detrital zircon ages of 505 to 501 million years old. When linked to calibrated trilobite zone ages of greater than 500 million years old, these age constraints show that the marine transgression across a greater than 300-km-wide cratonic region took place during an interval 505 to 500 million years ago—more recently and more rapidly than previously thought. We redefine this onlap as the main Sauk transgression in the region. Mechanisms for this rapid flooding of the continent include thermal subsidence following the final breakup of Rodinia, combined with abrupt global eustatic changes driven by climate and/or mantle buoyancy modifications.

Stratigraphy and sedimentology of the Upper Cretaceous (Campanian) Anacacho Limestone, Texas, USA

USGS Publications Warehouse

Swezey, C.S.; Sullivan, E.C.

2004-01-01

The Upper Cretaceous Anacacho Limestone is exposed in outcrops between the cities of San Antonio and Del Rio, Texas. A detailed study of four outcrops (Blanco Creek section, Sabinal River section, Seco Creek section, Hondo Creek section) shows that the Anacacho Limestone rests on the Upson Clay (which contains fauna of early Campanian age) and is overlain by the Corsicana Marl (which contains fauna of early Maastrichtian age). An unconformity within the Anacacho Limestone is used herein to separate the limestone into a lower member and an upper member. The lower Anacacho member contains fauna of early Campanian age, whereas the upper Anacacho member contains fauna of middle Campanian age. The lower Anacacho member consists predominantly of wackestones to packstones, which are overlain by packstones to grainstones capped by the unconformity. This unconformity is interpreted as a marine flooding surface, delineating a transition from carbonate grainstones deposited in shallow water (<30 m depth) to a chalk deposited in deeper water. Above the unconformity, the upper Anacacho member is characterized by a chalk, overlain by wackestones and packstones. The uppermost section of the Anacacho Limestone consists of packstones and grainstones with abundant and diverse fossils. Most of the Anacacho Limestone developed in relatively shallow water (<50 m depth) leeward of a large carbonate build-up (possibly a rudistid reef) that now comprises the Anacacho Mountains. The environment, however, was open to marine water throughout deposition of the Anacacho Limestone. ?? 2004 Elsevier Ltd. All rights reserved.

Exposure assessment of natural uranium from drinking water.

PubMed

Jakhu, Rajan; Mehra, Rohit; Mittal, H M

2016-12-08

The uranium concentration in the drinking water of the residents of the Jaipur and Ajmer districts of Rajasthan has been measured for exposure assessment. The daily intake of uranium from the drinking water for the residents of the study area is found to vary from 0.4 to 123.9 μg per day. For the average uranium ingestion rate of 35.2 μg per day for a long term exposure period of 60 years, estimations have been made for the retention of uranium in different body organs and its excretion with time using ICRP's biokinetic model of uranium. Radioactive and chemical toxicity of uranium has been reported and discussed in detail in the present manuscript.

Southwest USA Exhumation History Recorded Below the Great Unconformity

NASA Astrophysics Data System (ADS)

Heizler, M. T.; Karlstrom, K. E.

2002-05-01

The Southwestern USA Precambrian terranes preserve a long and variable exhumation history that can be tracked using thermochronological methods. This exhumation history is controlled on two interrelated scales. At first order, it is recognized that 1.7 to 1.4 Ga mid-crustal (10 km, 2-4 kbar) rocks were ultimately exhumed and reside below unconformities of variable age. In Arizona, Mesoproterozoic Apache Group and Neoproterozoic Supergroup sedimentary rocks lie directly on basement and thus indicate exhumation of some regions relatively soon following the 1.4 Ga events. In the Rocky Mountains of Colorado and the Rio Grande rift uplifts of New Mexico, basement is generally overlain by Cambrian to Mississippian strata. The unconformities are useful markers of net exhumation; however do not reveal a time-integrated path. Using published, and hundreds of new 40Ar/39Ar analyses of hornblende, muscovite, biotite and K-feldspar, and a growing U/Pb accessory mineral thermochronology database, we are extracting exhumation information with great detail. The thermochronological data continue to support the claim that relatively low net exhumation occurred following 1.7 to 1.6 Ga accretion of volcanic arc terranes to the southern margin of Laurentia. Mid-crustal (2-4 kbar) rocks stabilized soon after accretion, whereas in some regions like the Upper Granite Gorge, Grand Canyon deeper (6 kbar) metamorphic terranes decompressed to 3 kbar before stabilization. The cooling history of these mid-crustal rocks post 1.65 Ga remains somewhat unknown. Overall slow-cooling models (550 \\deg C to 300 \\deg C from 1.7 to 1.4 Ga) require high geothermal gradients in order to maintain 10 km deep rocks at high temperatures for 100's of Ma. Alternatively, isobaric cooling models to more normal geothermal gradients (i.e. 25 \\deg C/km) at ca. 1.65 Ga require later (1.4 Ga) thermal pulses and/or Mesoproterozoic vertical displacements to explain highly discordant thermochronological data. Either model supports relatively normal crustal thickness during 1.8-1.6 Ga arc accretion. In the Grand Canyon, cooling and exhumation are recorded at 1.4 Ga and 1.25 Ga. 1.4 Ga tectonism is shown by a sharp contrast in mica ages (1.4 vs. 1.6 Ga) across the 96-mile shear zone. The 1.25 Ga denudation is required by 1.25-1.30 Ga K-feldspar argon ages from basement that is unconformably overlain by a 1253 Ma volcanic ash horizon in the Unkar Group sediments. Arizona transition zone rocks of similar metamorphic pressure yield highly variable argon ages and indicate that small differences in exposed paleodepth can yield significantly different data. This is supported by cooling ages that systematically decrease with increase in paleodepth in the Gold Butte block, NV. Combined, the thermochronological data from the SW USA record a complex exhumation history that is characterized by discrete block uplift superimposed on an overall billion year erosional history that brings mid-crustal rocks to the surface a variable times.

Deposit model for volcanogenic uranium deposits

USGS Publications Warehouse

Breit, George N.; Hall, Susan M.

2011-01-01

The International Atomic Energy Agency's tabulation of volcanogenic uranium deposits lists 100 deposits in 20 countries, with major deposits in Russia, Mongolia, and China. Collectively these deposits are estimated to contain uranium resources of approximately 500,000 tons of uranium, which amounts to 6 percent of the known global resources. Prior to the 1990s, these deposits were considered to be small (less than 10,000 tons of uranium) with relatively low to moderate grades (0.05 to 0.2 weight percent of uranium). Recent availability of information on volcanogenic uranium deposits in Asia highlighted the large resource potential of this deposit type. For example, the Streltsovskoye district in eastern Russia produced more than 100,000 tons of uranium as of 2005; with equivalent resources remaining. Known volcanogenic uranium deposits within the United States are located in Idaho, Nevada, Oregon, and Utah. These deposits produced an estimated total of 800 tons of uranium during mining from the 1950s through the 1970s and have known resources of 30,000 tons of uranium. The most recent estimate of speculative resources proposed an endowment of 200,000 tons of uranium.

Development of evaluation models of manpower needs for dismantling the dry conversion process-related equipment in uranium refining and conversion plant (URCP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sari Izumo; Hideo Usui; Mitsuo Tachibana

Evaluation models for determining the manpower needs for dismantling various types of equipment in uranium refining and conversion plant (URCP) have been developed. The models are widely applicable to other uranium handling facilities. Additionally, a simplified model was developed for easily and accurately calculating the manpower needs for dismantling dry conversion process-related equipment (DP equipment). It is important to evaluate beforehand project management data such as manpower needs to prepare an optimized decommissioning plan and implement effective dismantling activity. The Japan Atomic Energy Agency (JAEA) has developed the project management data evaluation system for dismantling activities (PRODIA code), which canmore » generate project management data using evaluation models. For preparing an optimized decommissioning plan, these evaluation models should be established based on the type of nuclear facility and actual dismantling data. In URCP, the dry conversion process of reprocessed uranium and others was operated until 1999, and the equipment related to the main process was dismantled from 2008 to 2011. Actual data such as manpower for dismantling were collected during the dismantling activities, and evaluation models were developed using the collected actual data on the basis of equipment classification considering the characteristics of uranium handling facility. (authors)« less

Uranium resource assessment through statistical analysis of exploration geochemical and other data. Final report. [Codes EVAL, SURE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koch, G.S. Jr.; Howarth, R.J.; Schuenemeyer, J.H.

1981-02-01

We have developed a procedure that can help quadrangle evaluators to systematically summarize and use hydrogeochemical and stream sediment reconnaissance (HSSR) and occurrence data. Although we have not provided an independent estimate of uranium endowment, we have devised a methodology that will provide this independent estimate when additional calibration is done by enlarging the study area. Our statistical model for evaluation (system EVAL) ranks uranium endowment for each quadrangle. Because using this model requires experience in geology, statistics, and data analysis, we have also devised a simplified model, presented in the package SURE, a System for Uranium Resource Evaluation. Wemore » have developed and tested these models for the four quadrangles in southern Colorado that comprise the study area; to investigate their generality, the models should be applied to other quandrangles. Once they are calibrated with accepted uranium endowments for several well-known quadrangles, the models can be used to give independent estimates for less-known quadrangles. The point-oriented models structure the objective comparison of the quandrangles on the bases of: (1) Anomalies (a) derived from stream sediments, (b) derived from waters (stream, well, pond, etc.), (2) Geology (a) source rocks, as defined by the evaluator, (b) host rocks, as defined by the evaluator, and (3) Aerial radiometric anomalies.« less

Using proteomic data to assess a genome-scale "in silico" model of metal reducing bacteria in the simulation of field-scale uranium bioremediation

NASA Astrophysics Data System (ADS)

Yabusaki, S.; Fang, Y.; Wilkins, M. J.; Long, P.; Rifle IFRC Science Team

2011-12-01

A series of field experiments in a shallow alluvial aquifer at a former uranium mill tailings site have demonstrated that indigenous bacteria can be stimulated with acetate to catalyze the conversion of hexavalent uranium in a groundwater plume to immobile solid-associated uranium in the +4 oxidation state. While this bioreduction of uranium has been shown to lower groundwater concentrations below actionable standards, a viable remediation methodology will need a mechanistic, predictive and quantitative understanding of the microbially-mediated reactions that catalyze the reduction of uranium in the context of site-specific processes, properties, and conditions. At the Rifle IFRC site, we are investigating the impacts on uranium behavior of pulsed acetate amendment, acetate-oxidizing iron and sulfate reducing bacteria, seasonal water table variation, spatially-variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. The simulation of three-dimensional, variably saturated flow and biogeochemical reactive transport during a uranium bioremediation field experiment includes a genome-scale in silico model of Geobacter sp. to represent the Fe(III) terminal electron accepting process (TEAP). The Geobacter in silico model of cell-scale physiological metabolic pathways is comprised of hundreds of intra-cellular and environmental exchange reactions. One advantage of this approach is that the TEAP reaction stoichiometry and rate are now functions of the metabolic status of the microorganism. The linkage of in silico model reactions to specific Geobacter proteins has enabled the use of groundwater proteomic analyses to assess the accuracy of the model under evolving hydrologic and biogeochemical conditions. In this case, the largest predicted fluxes through in silico model reactions generally correspond to high abundances of proteins linked to those reactions (e.g. the condensation reaction catalyzed by the protein citrate synthase that generates citrate from acetyl-CoA and oxaloacetate). Model discrepancies with the proteomic data, such as the prediction of shifts associated with nitrogen limitation, revealed pathways in the in silico code that could be modified to more accurately predict metabolic processes that occur in the subsurface. The potential outcome of this approach is the engineering of electron donor (e.g., acetate), terminal electron acceptor [e.g., U(VI)], and biogeochemical conditions that enhance the desired metabolic pathways of the target microorganism(s) to effect cost-effective uranium bioreduction.

Weathering and evaporation controls on dissolved uranium concentrations in groundwater - A case study from northern Burundi.

PubMed

Post, V E A; Vassolo, S I; Tiberghien, C; Baranyikwa, D; Miburo, D

2017-12-31

The potential use of groundwater for potable water supply can be severely compromised by natural contaminants such as uranium. The environmental mobility of uranium depends on a suite of factors including aquifer lithology, redox conditions, complexing agents, and hydrological processes. Uranium concentrations of up to 734μg/L are found in groundwater in northern Burundi, and the objective of the present study was to identify the causes for these elevated concentrations. Based on a comprehensive data set of groundwater chemistry, geology, and hydrological measurements, it was found that the highest dissolved uranium concentrations in groundwater occur near the shores of Lake Tshohoha South and other smaller lakes nearby. A model is proposed in which weathering and evapotranspiration during groundwater recharge, flow and discharge exert the dominant controls on the groundwater chemical composition. Results of PHREEQC simulations quantitatively confirm this conceptual model and show that uranium mobilization followed by evapo-concentration is the most likely explanation for the high dissolved uranium concentrations observed. The uranium source is the granitic sand, which was found to have a mean elemental uranium content of 14ppm, but the exact mobilization process could not be established. Uranium concentrations may further be controlled by adsorption, especially where calcium-uranyl‑carbonate complexes are present. Water and uranium mass balance calculations for Lake Tshohoha South are consistent with the inferred fluxes and show that high‑uranium groundwater represents only a minor fraction of the overall water input to the lake. These findings highlight that the evaporation effects that cause radionuclide concentrations to rise to harmful levels in groundwater discharge areas are not only confined to arid regions, and that this should be considered when selecting suitable locations for water supply wells. Copyright © 2017 Elsevier B.V. All rights reserved.

Uranium hexafluoride public risk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisher, D.R.; Hui, T.E.; Yurconic, M.

1994-08-01

The limiting value for uranium toxicity in a human being should be based on the concentration of uranium (U) in the kidneys. The threshold for nephrotoxicity appears to lie very near 3 {mu}g U per gram kidney tissue. There does not appear to be strong scientific support for any other improved estimate, either higher or lower than this, of the threshold for uranium nephrotoxicity in a human being. The value 3 {mu}g U per gram kidney is the concentration that results from a single intake of about 30 mg soluble uranium by inhalation (assuming the metabolism of a standard person).more » The concentration of uranium continues to increase in the kidneys after long-term, continuous (or chronic) exposure. After chronic intakes of soluble uranium by workers at the rate of 10 mg U per week, the concentration of uranium in the kidneys approaches and may even exceed the nephrotoxic limit of 3 {mu}g U per gram kidney tissue. Precise values of the kidney concentration depend on the biokinetic model and model parameters assumed for such a calculation. Since it is possible for the concentration of uranium in the kidneys to exceed 3 {mu}g per gram tissue at an intake rate of 10 mg U per week over long periods of time, we believe that the kidneys are protected from injury when intakes of soluble uranium at the rate of 10 mg U per week do not continue for more than two consecutive weeks. For long-term, continuous occupational exposure to low-level, soluble uranium, we recommend a reduced weekly intake limit of 5 mg uranium to prevent nephrotoxicity in workers. Our analysis shows that the nephrotoxic limit of 3 {mu}g U per gram kidney tissues is not exceeded after long-term, continuous uranium intake at the intake rate of 5 mg soluble uranium per week.« less

Stromatolites at ~3,500 Myr and a greenstone-granite unconformity in the Zimbabwean Archaean

NASA Astrophysics Data System (ADS)

Orpen, J. L.; Wilson, J. F.

1981-05-01

Two controversial areas of geological endeavour are the establishment of the antiquity of life and the tectonic setting of greenstone sequences. We record here the recent discoveries in the Fort Victoria greenstone belt of stromatolites in limestones assigned to ~3,500 Myr (minimum age) Sebakwian Group rocks of the Rhodesian Archaean Craton within Zimbabwe, and a nearby outcrop of a thin sedimentary formation, basal to a thick ~2,700 Myr volcanic pile, resting with definite unconformity on ~3,500 Myr Mushandike Granite.

Global Modeling of Uranium Molecular Species Formation Using Laser-Ablated Plasmas

NASA Astrophysics Data System (ADS)

Curreli, Davide; Finko, Mikhail; Azer, Magdi; Armstrong, Mike; Crowhurst, Jonathan; Radousky, Harry; Rose, Timothy; Stavrou, Elissaios; Weisz, David; Zaug, Joseph

2016-10-01

Uranium is chemically fractionated from other refractory elements in post-detonation nuclear debris but the mechanism is poorly understood. Fractionation alters the chemistry of the nuclear debris so that it no longer reflects the chemistry of the source weapon. The conditions of a condensing fireball can be simulated by a low-temperature plasma formed by vaporizing a uranium sample via laser heating. We have developed a global plasma kinetic model in order to model the chemical evolution of U/UOx species within an ablated plasma plume. The model allows to track the time evolution of the density and energy of an uranium plasma plume moving through an oxygen atmosphere of given fugacity, as well as other relevant quantities such as average electron and gas temperature. Comparison of model predictions with absorption spectroscopy of uranium-ablated plasmas provide preliminary insights on the key chemical species and evolution pathways involved during the fractionation process. This project was sponsored by the DoD, Defense Threat Reduction Agency, Grant HDTRA1-16-1-0020. This work was performed in part under the auspices of the U.S. DoE by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Modelling of the dissolution and reprecipitation of uranium under oxidising conditions in the zone of shallow groundwater circulation.

PubMed

Dutova, Ekaterina M; Nikitenkov, Aleksei N; Pokrovskiy, Vitaly D; Banks, David; Frengstad, Bjørn S; Parnachev, Valerii P

2017-11-01

Generic hydrochemical modelling of a grantoid-groundwater system, using the Russian software "HydroGeo", has been carried out with an emphasis on simulating the accumulation of uranium in the aqueous phase. The baseline model run simulates shallow granitoid aquifers (U content 5 ppm) under conditions broadly representative of southern Norway and southwestern Siberia: i.e. temperature 10 °C, equilibrated with a soil gas partial CO 2 pressure (P CO2 , open system) of 10 -2.5 atm. and a mildly oxidising redox environment (Eh = +50 mV). Modelling indicates that aqueous uranium accumulates in parallel with total dissolved solids (or groundwater mineralisation M - regarded as an indicator of degree of hydrochemical evolution), accumulating most rapidly when M = 550-1000 mg L -1 . Accumulation slows at the onset of saturation and precipitation of secondary uranium minerals at M = c. 1000 mg L -1 (which, under baseline modelling conditions, also corresponds approximately to calcite saturation and transition to Na-HCO 3 hydrofacies). The secondary minerals are typically "black" uranium oxides of mixed oxidation state (e.g. U 3 O 7 and U 4 O 9 ). For rock U content of 5-50 ppm, it is possible to generate a wide variety of aqueous uranium concentrations, up to a maximum of just over 1 mg L -1 , but with typical concentrations of up to 10 μg L -1 for modest degrees of hydrochemical maturity (as indicated by M). These observations correspond extremely well with real groundwater analyses from the Altai-Sayan region of Russia and Norwegian crystalline bedrock aquifers. The timing (with respect to M) and degree of aqueous uranium accumulation are also sensitive to Eh (greater mobilisation at higher Eh), uranium content of rocks (aqueous concentration increases as rock content increases) and P CO2 (low P CO2 favours higher pH, rapid accumulation of aqueous U and earlier saturation with respect to uranium minerals). Copyright © 2017 Elsevier Ltd. All rights reserved.

Study on kinetics of adsorption of humic acid modified by ferric chloride on U(VI)

NASA Astrophysics Data System (ADS)

Zhang, Y. Y.; Lv, J. W.; Song, Y.; Dong, X. J.; Fang, Q.

2017-11-01

In order to reveal the adsorption mechanism of the ferric chloride modified humic acid on uranium, the influence of pH value and contact time of adsorption on uranium was studied through a series of batch experiments. Meanwhile, the adsorption kinetics was analyzed with pseudo-first order kinetic model and pseudo-second order kinetic model. The results show that adsorption is affected by the pH value of the solution and by contract time, and the best condition for adsorption on uranium is at pH=5 and the adsorption equilibrium time is about 80 min. Kinetics of HA-Fe adsorption on uranium accords with pseudo-second order kinetic model. The adsorption is mainly chemical adsorption, and complexes were produced by the reaction between uranium ions and the functional groups on the surface of HA-Fe, which can provide reference for further study of humic acid effecting on the migration of U(VI) in soil.

Novel Sensor for the In Situ Measurement of Uranium Fluxes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hatfield, Kirk

2015-02-10

The goal of this project was to develop a sensor that incorporates the field-tested concepts of the passive flux meter to provide direct in situ measures of flux for uranium and groundwater in porous media. Measurable contaminant fluxes [J] are essentially the product of concentration [C] and groundwater flux or specific discharge [q ]. The sensor measures [J] and [q] by changes in contaminant and tracer amounts respectively on a sorbent. By using measurement rather than inference from static parameters, the sensor can directly advance conceptual and computational models for field scale simulations. The sensor was deployed in conjunction withmore » DOE in obtaining field-scale quantification of subsurface processes affecting uranium transport (e.g., advection) and transformation (e.g., uranium attenuation) at the Rifle IFRC Site in Rifle, Colorado. Project results have expanded our current understanding of how field-scale spatial variations in fluxes of uranium, groundwater and salient electron donor/acceptors are coupled to spatial variations in measured microbial biomass/community composition, effective field-scale uranium mass balances, attenuation, and stability. The coupling between uranium, various nutrients and micro flora can be used to estimate field-scale rates of uranium attenuation and field-scale transitions in microbial communities. This research focuses on uranium (VI), but the sensor principles and design are applicable to field-scale fate and transport of other radionuclides. Laboratory studies focused on sorbent selection and calibration, along with sensor development and validation under controlled conditions. Field studies were conducted at the Rifle IFRC Site in Rifle, Colorado. These studies were closely coordinated with existing SBR (formerly ERSP) projects to complement data collection. Small field tests were conducted during the first two years that focused on evaluating field-scale deployment procedures and validating sensor performance under controlled field conditions. In the third and fourth year a suite of larger field studies were conducted. For these studies, the uranium flux sensor was used with uranium speciation measurements and molecular-biological tools to characterize microbial community and active biomass at synonymous wells distributed in a large grid. These field efforts quantified spatial changes in uranium flux and field-scale rates of uranium attenuation (ambient and stimulated), uranium stability, and quantitatively assessed how fluxes and effective reaction rates were coupled to spatial variations in microbial community and active biomass. Analyses of data from these field experiments were used to generate estimates of Monod kinetic parameters that are ‘effective’ in nature and optimal for modeling uranium fate and transport at the field-scale. This project provided the opportunity to develop the first sensor that provides direct measures of both uranium (VI) and groundwater flux. A multidisciplinary team was assembled to include two geochemists, a microbiologist, and two quantitative contaminant hydrologists. Now that the project is complete, the sensor can be deployed at DOE sites to evaluate field-scale uranium attenuation, source behavior, the efficacy of remediation, and off-site risk. Because the sensor requires no power, it can be deployed at remote sites for periods of days to months. The fundamental science derived from this project can be used to advance the development of predictive models for various transport and attenuation processes in aquifers. Proper development of these models is critical for long-term stewardship of contaminated sites in the context of predicting uranium source behavior, remediation performance, and off-site risk.« less

Innovative mathematical modeling in environmental remediation.

PubMed

Yeh, Gour-Tsyh; Gwo, Jin-Ping; Siegel, Malcolm D; Li, Ming-Hsu; Fang, Yilin; Zhang, Fan; Luo, Wensui; Yabusaki, Steve B

2013-05-01

There are two different ways to model reactive transport: ad hoc and innovative reaction-based approaches. The former, such as the Kd simplification of adsorption, has been widely employed by practitioners, while the latter has been mainly used in scientific communities for elucidating mechanisms of biogeochemical transport processes. It is believed that innovative mechanistic-based models could serve as protocols for environmental remediation as well. This paper reviews the development of a mechanistically coupled fluid flow, thermal transport, hydrologic transport, and reactive biogeochemical model and example-applications to environmental remediation problems. Theoretical bases are sufficiently described. Four example problems previously carried out are used to demonstrate how numerical experimentation can be used to evaluate the feasibility of different remediation approaches. The first one involved the application of a 56-species uranium tailing problem to the Melton Branch Subwatershed at Oak Ridge National Laboratory (ORNL) using the parallel version of the model. Simulations were made to demonstrate the potential mobilization of uranium and other chelating agents in the proposed waste disposal site. The second problem simulated laboratory-scale system to investigate the role of natural attenuation in potential off-site migration of uranium from uranium mill tailings after restoration. It showed inadequacy of using a single Kd even for a homogeneous medium. The third example simulated laboratory experiments involving extremely high concentrations of uranium, technetium, aluminum, nitrate, and toxic metals (e.g., Ni, Cr, Co). The fourth example modeled microbially-mediated immobilization of uranium in an unconfined aquifer using acetate amendment in a field-scale experiment. The purposes of these modeling studies were to simulate various mechanisms of mobilization and immobilization of radioactive wastes and to illustrate how to apply reactive transport models for environmental remediation. Copyright © 2011 Elsevier Ltd. All rights reserved.

Nevada Test and Training Range Depleted Uranium Target Disposal Environmental Assessment

DTIC Science & Technology

2005-03-01

to establish the probability and scope of such transport. Long-Term Fate of Depleted Uranium at Aberdeen and Yuma Proving Grounds Phase II: Human...1990. Long-Term Fate of Depleted Uranium at Aberdeen and Yuma Proving Grounds Final Report, Phase 1: Geochemical Transport and Modeling. Los...of Depleted Uranium at Aberdeen and Yuma Proving Grounds , Phase II: Human Health and Ecological Risk Assessments. Los Alamos National Laboratory

Mesozoic­ and Cenozoic Tectono-depositional History of the Southwestern Chukchi Borderland: Implications of Pre-Brookian Passive-margin Slope Deposits for the Jurassic Extensional Deformation of the Amerasia Basin, Arctic Ocean

NASA Astrophysics Data System (ADS)

Ilhan, I.; Coakley, B.

2016-12-01

A stratigraphic framework for offshore northwest of Alaska has been developed from multi-channel seismic reflection data and direct seismic-well ties to the late 80's Crackerjack and Popcorn exploration wells along the late Cretaceous middle Brookian unconformity. This unconformity is characterized by downlap, onlap, and bi-directional onlap of the overlying upper Brookian strata in high accommodation, and erosional incision of the underlying lower Brookian strata in low accommodation. This surface links multiple basins across the southwestern Chukchi Borderland, Arctic Ocean. The lower Brookian strata are characterized by pinch out basin geometry in which parallel-continuous reflectors show north-northeasterly progressive onlap of the younger strata onto a lower Cretaceous unconformity. These strata are subdivided into Aptian-Albian and Upper Cretaceous sections along a middle Cretaceous unconformity. The north-northeasterly thinning-by-onlap is consistent across hundreds of kilometers along the southwestern Chukchi Borderland. While this suggests a south-southwesterly regional source of sediment and transport from the Early Cretaceous Arctic Alaska-Chukotka orogens, pre-Brookian clinoform strata, underlying the lower Cretaceous unconformity angularly, have been observed for the first time in southeastern margin of the Chukchi Abyssal Plain. This suggests a change in sediment source and transport direction between the pre-Brookian and the lower Brookian strata. Although the mechanism for the accommodation is not well understood, we interpret the pre-Brookian strata as passive-margin slope deposits due to the fact that we have not observed any evidence for upper crustal tectonic deformation or syn-tectonic "growth" strata in the area. Thus, this implies that depositional history of the southwestern Chukchi Borderland post-dates the accommodation. This interpretation puts a new substantial constrain on the pre-Valanginian clockwise rotation of the Chukchi Borderland away from the East Siberian continental shelf, associated with the antecedent counter-clockwise rotation of the Arctic Alaska-Chukotka microplate away from the Canadian Arctic Islands and extensional deformation of the Amerasia Basin.

Record of Subducting Topography revealed in 3D Seismic Imaging of Pleistocene unconformities, offshore Southern Costa Rica

NASA Astrophysics Data System (ADS)

Edwards, J. H.; Kluesner, J. W.; Silver, E. A.

2015-12-01

3D seismic reflection data (CRISP) collected across the southern Costa Rica forearc reveals broad, survey-wide erosional events in the upper ~1 km of slope sediments in the mid-slope to outer shelf. The upper 0-280 m of continuous, weakly deformed sediments, designated by IODP Expedition 344 as structural domain I, is bounded by a major erosional event, (CRISP-U1, dated near 1 Ma), suggesting wave-plain erosion from the present shelf break out to 25 km seaward, to a present-day water depth of 900-1300 m. The eastern toe of its surface is characterized by a large drainage system, likely including submarine channels that eroded to depths >1500 m below present-day water depth. CRISP-U1 is variably uplifted by a series of fault propagation folds and cut by an intersecting array of normal faults. Another, major erosional event, (CRISP-M1, approximately 2 Ma) extended from the outer shelf to the mid slope and removed 500-1000 m of material. Overlying CRISP-M1 is up to 1 km of sediments that are more deformed by fault propagation folds, back thrusts, and intersecting arrays of normal faults. Unconformities with smaller areal extent are variably found in these overlying sediments across the mid-slope to outer shelf, at present-day water depths >220 m. Below CRISP-M1, sediments are more densely deformed and also contain major unconformities that extend survey-wide. Both unconformities, CRISP-U1 and CRISP-M1, are encountered in well U1413 and are demarcated by major benthic foraminifera assemblage changes at 149 mbsf and ~504 mbsf (Harris et al., 2013, Proceeding of the IODP, Volume 344).CRISP-M1 is likely correlative to the major sediment facies and benthic foraminifera assemblage change found in U1379 at ~880 mbsf (Vannuchi et al., 2013). The unconformities and intersecting array of normal faults may demarcate the passing of topography on the downgoing Cocos plate, episodically lifting and then subsiding the Costa Rica margin, with amplitudes up to about 1 km.

The Rajang Unconformity: Major provenance change between the Eocene and Miocene sequences in NW Borneo

NASA Astrophysics Data System (ADS)

Breitfeld, H. T.; Hennig, J.; BouDagher-Fadel, M.; Hall, R.

2017-12-01

The offshore Sarawak Basin NW of North Sarawak is a major hydrocarbon province in SE Asia. A very thick sedimentary sequence of Oligocene to ?Early Miocene age, named Cycle 1, is an important hydrocarbon source and reservoir. Despite numerous wells the stratigraphy and tectonic history is not very well understood. The Nyalau Formation of onshore North Sarawak is the supposed equivalent of the offshore Cycle 1 sequence. The Nyalau Formation is a thick sedimentary sequence of mainly tidal to deltaic deposits. The formation is dominated by well-bedded sandstone-mudstone alternations and thicker sandstones with abundant bioturbation. The sandstones are predominantly arenaceous. Various lithic fragments and feldspar indicate multiple sources and fresh input from igneous and metamorphic rocks. Interbedded thin limestone beds and marls yielded Early Miocene foraminifera for the upper part of the succession. Zircons separated from the sandstones yielded mainly Cretaceous and Triassic ages. The Triassic is the dominant age population. The Nyalau Formation conformably overlies the Buan Shale and the Tatau Formation, and in places unconformably overlies the Belaga Formation. The Belaga Formation is part of the Rajang Group that represents remnants of a large submarine fan deposited in the Late Cretaceous to Eocene in Central Sarawak. In contrast to the Nyalau Formation, the majority of zircons from the Rajang Group have Cretaceous ages. This marks an important change in provenance at the major unconformity separating the Belaga and Nyalau Formations. This unconformity was previously interpreted as the result of an orogeny in the Late Eocene. However, there is no evidence for a subduction or collision event at this time in Sarawak. We interpret it to mark plate reorganisation in the Middle Eocene and name it the Rajang Unconformity. Borneo is the principal source of Cretaceous zircons which were derived from the Schwaner Mountains and West Sarawak. The dominant Triassic zircon age population in the Nyalau Formation indicates either major input from the Malay Peninsula (Malay-Thai Tin belt) or Indochina (SE Vietnam). It also suggests that Borneo supplied little or no sediment to Sarawak in the Oligocene to Early Miocene.

Removal of uranium and fluorine from wastewater by double-functional microsphere adsorbent of SA/CMC loaded with calcium and aluminum

NASA Astrophysics Data System (ADS)

Wu, Liping; Lin, Xiaoyan; Zhou, Xingbao; Luo, Xuegang

2016-10-01

A novel dual functional microsphere adsorbent of alginate/carboxymethyl cellulose sodium composite loaded with calcium and aluminum (SA/CMC-Ca-Al) is prepared by an injection device to remove fluoride and uranium, respectively, from fluoro-uranium mixed aqueous solution. Batch experiments are performed at different conditions: pH, temperature, initial concentration and contact time. The results show that the maximum adsorption amount for fluoride is 35.98 mg/g at pH 2.0, 298.15 K concentration 100 mg/L, while that for uranium is 101.76 mg/g at pH 4.0, 298.15 K concentration 100 mg/L. Both of the adsorption process could be well described by Langmuir model. The adsorption kinetic data is fitted well with pseudo-first-order model for uranium and pseudo-second-order model for fluoride. Thermodynamic parameters are also evaluated, indicating that the adsorption of uranium on SA/CMC-Ca-Al is a spontaneous and exothermic process, while the removal of fluoride is non-spontaneous and endothermic process. The mechanism of modification and adsorption process on SA/CMC-Ca-Al is characterized by FT-IR, SEM, EDX and XPS. The results show that Ca (II) and Al (III) are loaded on SA/CMC through ion-exchange of sodium of SA/CMC. The coordination reaction and ion-exchange happen during the adsorption process between SA/CMC-Ca-Al and uranium, fluoride. Results suggest that the SA/CMC-Ca-Al adsorbent has a great potential in removing uranium and fluoride from aqueous solution.

Geologic framework of lower Cook Inlet, Alaska

USGS Publications Warehouse

Fisher, M.A.; Magoon, L.B.

1978-01-01

Three seismic reflectors are present throughout the lower Cook Inlet basin and can be correlated with onshore geologic features. The reflections come from unconformities at the base of the Tertiary sequence, at the base of Upper Cretaceous rocks, and near the base of Upper Jurassic strata. A contour map of the deepest horizon shows that Mesozoic rocks are formed into a northeast-trending syncline. Along the southeast flank of the basin, the northwest-dipping Mesozoic rocks are truncated at the base of Tertiary rocks. The Augustine-Seldovia arch trends across the basin axis between Augustine Island and Seldovia. Tertiary rocks thin onto the arch from the north and south. Numerous anticlines, smaller in structural relief and breadth than the Augustine-Seldovia arch, trend northeast parallel with the basin, and intersect the arch at oblique angles. The stratigraphic record shows four cycles of sedimentation and tectonism that are bounded by three regional unconformities in lower Cook Inlet and by four thrust faults and the modern Benioff zone in flysch rocks of the Kenai Peninsula and the Gulf of Alaska. The four cycles of sedimentation are, from oldest to youngest, the early Mesozoic, late Mesozoic, early Cenozoic, and late Cenozoic. Data on organic geochemistry of the rocks from one well suggest that Middle Jurassic strata may be a source of hydrocarbons. Seismic data show that structural traps are formed by northeast-trending anticlines and by structures formed at the intersections of these anticlines with the transbasin arch. Stratigraphic traps may be formed beneath the unconformity at the base of Tertiary strata and beneath unconformities within Mesozoic strata.

Lomonosov Ridge, Arctic Ocean: New MCS Data for the Definition of Targets for Scientific Drilling

NASA Astrophysics Data System (ADS)

Kristoffersen, Y.; Coakley, B.; Hall, J. K.

2001-12-01

The 1500 km long and 50-150 km wide Lomonosov Ridge rises more than 3000 m above the adjacent abyssal plains, separating the Mesozoic-aged Amerasian basin from the Cenozoic-Recent Eurasian basin. Multichannel seismic reflection data collected from icebreakers on four cruises together with swath bathymetry and high resolution chirp sonar data collected by nuclear submarines across the central ridge show a cap of hemipelagic drape (c. 450 m thick) on top of normal faulted and peneplained sedimentary sequences, the remnants of the Mesozoic Barents margin, which pre-dates the opening of the Eurasian Basin. A new multichannel seismic survey to augment the site survey data base for ODP proposal 533 was carried out on the Lomonosov Ridge under difficult ice conditions in late July 2001 from the Swedish icebreaker Oden. The primary objectives of ODP Proposal 533 are to obtain continuous paleoceanographic records for most of the Cenozoic from the hemipelagic sequence and to sample the underlying passive margin sequence below the regional unconformity, which would provide the first direct constraints on the early tectonic history of the ridge. Of particular interest is the extent of mass wasting along the ridge perimeter. This regional unconformity offers an opportunity for implementing a strategy of offset shallow drill holes to obtain a complete hemi-pelagic section as well as to penetrate the regional unconformity. The new data, which will, in conjunction with the existing MCS data base, provide the first 3-D control on the passive margin structures and overlying unconformity, will be presented.

Major unconformities/termination of extension events and associated surfaces in the South China Seas: Review and implications for tectonic development

NASA Astrophysics Data System (ADS)

Morley, C. K.

2016-04-01

The distribution of unconformities and end of Cenozoic rifting events in the South China Seas (SCS) reflects both the modes of rift development, and the effects of driving mechanisms. Continental rifting began in the eastern basins during the Paleocene, and propagated westwards to the Vietnam basin margin in the Late Eocene. Continental breakup around 32-28 Ma caused a regional reduction or cessation in extensional activity, particularly affecting basins furthest from the spreading centre. Basins in the slope and deepwater area north of the spreading centre exhibit reduced fault activity until 21-20 Ma. Propagation of oceanic crust westwards between ∼25 and 23 Ma, and termination of seafloor spreading sometime between 20.5 and 16 Ma affected fault activity in the Qiongdongnan, and Nam Con Song basins. In the Phu Khanh Basin and South, in the Dangerous Grounds area, extension continued until about 16 Ma, ending at the Red Unconformity. The end of seafloor spreading around 20.5 Ma reflects loss of extensional driving force as thinned continental crust entered the NW Borneo subduction zone. Controversially, a key component of the driving force maybe attributed to slab-pull. A transitional period of about 5-7 my between the onset of subduction of continental crust, and final jamming of the subduction zone (Deep Regional Unconformity, DRU) is inferred. The last pulse of extension was focussed in the western SCS, and terminated around 10.5 Ma. Detailed understanding of proto South China Seas development remains uncertain and controversial.

Alpha spectrometric characterization of process-related particle size distributions from active particle sampling at the Los Alamos National Laboratory uranium foundry

NASA Astrophysics Data System (ADS)

Plionis, A. A.; Peterson, D. S.; Tandon, L.; LaMont, S. P.

2010-03-01

Uranium particles within the respirable size range pose a significant hazard to the health and safety of workers. Significant differences in the deposition and incorporation patterns of aerosols within the respirable range can be identified and integrated into sophisticated health physics models. Data characterizing the uranium particle size distribution resulting from specific foundry-related processes are needed. Using personal air sampling cascade impactors, particles collected from several foundry processes were sorted by activity median aerodynamic diameter onto various Marple substrates. After an initial gravimetric assessment of each impactor stage, the substrates were analyzed by alpha spectrometry to determine the uranium content of each stage. Alpha spectrometry provides rapid non-distructive isotopic data that can distinguish process uranium from natural sources and the degree of uranium contribution to the total accumulated particle load. In addition, the particle size bins utilized by the impactors provide adequate resolution to determine if a process particle size distribution is: lognormal, bimodal, or trimodal. Data on process uranium particle size values and distributions facilitate the development of more sophisticated and accurate models for internal dosimetry, resulting in an improved understanding of foundry worker health and safety.

Rheological implications of sediment transport for continental rifting and its impact in margin geometry and major unconformities

NASA Astrophysics Data System (ADS)

Andres-Martinez, Miguel; Perez-Gussinye, Marta; Armitage, John; Morgan, Jason

2016-04-01

The inner dynamics of the Earth such as mantle convection, geochemical reactions and isostasy have been typically interpreted as the main engine of plate tectonics and crustal deformation. However, nowadays it is well established that processes transporting material along the surface of the Earth influence the inner dynamics. Surface processes play a key role particularly during rifting, where great subsidence rates occur at synrift basins while shoulder uplift provides rock to be eroded for later infilling of these basins. Erosion implies unloading of the crust which favours uplift, and sedimentation at basins results in loading which favours subsidence. Consequently, erosion and sedimentation amplify stresses and the flexural response of the lithosphere in situations with extensive faulting. These changes to the stress field may be large enough to result in changes in the evolution of rifting and its modes of extension. Additionally, higher subsidence rates and thermal blanketing due to sediments may result in higher geotherms and consequently, a weaker/more-viscous behaviour of the crustal rocks. This would also have a large impact on the deformation style during extension. Here, we explore the interactions between surface processes and tectonics using numerical modelling. Experiments are run with the absence of sediment transport and with different sediment transport regimes for 35 and 40 km crustal thicknesses. Tests with higher transport coefficient show more effective localization of deformation into upper crustal faults which results in effective crustal thinning, larger blocks and longer-lived faults. Our experiments also prove that more effective surface processes reduce the length of margins generated by sequential faulting. For our end member situations, high sedimentation rates lead to pure shear extension of the crust induced by high temperatures, which finally results in broad extension and symmetric margins. Furthermore, our model allows for the recovery of predicted sediment stratigraphic patterns. Major unconformities that separate synrift from sag-basin-type sediments are observed in these pseudo-strata patterns. Here, we also address the meaning of these major unconformities and their relationship to the time of breakup.

Regional stratigraphic cross sections of Cretaceous rocks from east-central Arizona to the Oklahoma Panhandle

USGS Publications Warehouse

Molenaar, C.M.; Cobban, W.A.; Merewether, E.A.; Pillmore, C.L.; Wolfe, D.G.; Holbrook, J.M.

2002-01-01

Sedimentary rocks of Cretaceous age along Transect DD'' in eastern Arizona, northern New Mexico, southern Colorado, and western Oklahoma consist mainly of sandstone, siltstone, shale, limestone, and bentonite. They accumulated as sediments in continental, nearshore marine, and offshore marine environments on the west side of a north-trending epicontinental sea. The rocks record intermittent deposition and erosion as well as regional and local subsidence and uplift possibly beginning in Aptian time (about 121-112 Ma) and occurring in Albian through Maastrichtian time (about 112-65.4 Ma). Most of the Lower Cretaceous (Berriasian through Aptian, 142-112 Ma) in this transect is represented by a basal unconformity. The Cretaceous rocks and unconformities along the transect are depicted on the attached lithostratigraphic cross sections (sheets 1 and 2); one extending from the Mogollon Rim in eastern Arizona to Pagosa Springs in southwestern Colorado and the other from Pagosa Springs, Colorado, to Kenton in western Oklahoma. The same rocks and unconformities are also represented on the attached chronostratigraphic profile (sheet 3), which was prepared mainly from surface and subsurface data shown on the lithostratigraphic cross sections.

Can we predict uranium bioavailability based on soil parameters? Part 2: soil solution uranium concentration is not a good bioavailability index.

PubMed

Vandenhove, H; Van Hees, M; Wannijn, J; Wouters, K; Wang, L

2007-01-01

The present study aimed to quantify the influence of soil parameters on uranium uptake by ryegrass. Ryegrass was established on eighteen distinct soils, spiked with (238)U. Uranium soil-to-plant transfer factors (TF) ranged from 0.0003 to 0.0340kgkg(-1). There was no significant relation between the U soil-to-plant transfer (or total U uptake or flux) and the uranium concentration in the soil solution or any other soil factor measured, nor with the U recovered following selective soil extractions. Multiple linear regression analysis resulted in a significant though complex model explaining up to 99% of variation in TF. The influence of uranium speciation on uranium uptake observed was featured: UO(2)(+2), uranyl carbonate complexes and UO(2)PO(4)(-) seem the U species being preferentially taken up by the roots and transferred to the shoots. Improved correlations were obtained when relating the uranium TF with the summed soil solution concentrations of mentioned uranium species.

Sorption of uranium (VI) on homoionic sodium smectite experimental study and surface complexation modeling.

PubMed

Korichi, Smain; Bensmaili, Aicha

2009-09-30

This paper is an extension of a previous paper where the natural and purified clay in the homoionic Na form were physico-chemically characterized (doi:10.1016/j.clay.2008.04.014). In this study, the adsorption behavior of U (VI) on a purified Na-smectite suspension is studied using batch adsorption experiments and surface complexation modeling (double layer model). The sorption of uranium was investigated as a function of pH, uranium concentration, solid to liquid ratio, effect of natural organic matter (NOM) and NaNO(3) background electrolyte concentration. Using the MINTEQA2 program, the speciation of uranium was calculated as a function of pH and uranium concentration. Model predicted U (VI) aqueous speciation suggests that important aqueous species in the [U (VI)]=1mg/L and pH range 3-7 including UO(2)(2+), UO(2)OH(+), and (UO(2))(3)(OH)(5)(+). The concentration of UO(2)(2+) decreased and that of (UO(2))(3)(OH)(5)(+) increased with increasing pH. The potentiometric titration values and uptake of uranium in the sodium smectite suspension were simulated by FITEQL 4.0 program using a two sites model, which is composed of silicate and aluminum reaction sites. We compare the acidity constants values obtained by potentiometric titration from the purified sodium smectite with those obtained from single oxides (quartz and alpha-alumina), taking into account the surface heterogeneity and the complex nature of natural colloids. We investigate the uranium sorption onto purified Na-smectite assuming low, intermediate and high edge site surfaces which are estimated from specific surface area percentage. The sorption data is interpreted and modeled as a function of edge site surfaces. A relationship between uranium sorption and total site concentration was confirmed and explained through variation in estimated edge site surface value. The modeling study shows that, the convergence during DLM modeling is related to the best estimation of the edge site surface from the N(2)-BET specific surface area, SSA(BET) (thus, total edge site concentrations). The specific surface area should be at least 80-100m(2)/g for smectite clays in order to reach convergence during the modeling. The range of 10-20% SSA(BET) was used to estimate the values of edge site surfaces that led to the convergence during modeling. An agreement between the experimental data and model predictions is found reasonable when 15% SSA(BET) was used as edge site surface. However, the predicted U (VI) adsorption underestimated and overestimated the experimental observations at the 10 and 20% of the measured SSA(BET), respectively. The dependence of uranium sorption modeling results on specific surface area and edge site surface is useful to describe and predict U (VI) retardation as a function of chemical conditions in the field-scale reactive transport simulations. Therefore this approach can be used in the environmental quality assessment.

Application of the 226Ra– 230Th– 234U and 227Ac– 231Pa– 235U radiochronometers to uranium certified reference materials

DOE PAGES

Rolison, John M.; Treinen, Kerri C.; McHugh, Kelly C.; ...

2017-11-06

Uranium certified reference materials (CRM) issued by New Brunswick Laboratory were subjected to dating using four independent uranium-series radiochronometers. In all cases, there was acceptable agreement between the model ages calculated using the 231Pa– 235U, 230Th– 234U, 227Ac– 235U or 226Ra– 234U radiochronometers and either the certified 230Th– 234U model date (CRM 125-A and CRM U630), or the known purification date (CRM U050 and CRM U100). Finally, the agreement between the four independent radiochronometers establishes these uranium certified reference materials as ideal informal standards for validating dating techniques utilized in nuclear forensic investigations in the absence of standards with certifiedmore » model ages for multiple radiochronometers.« less

Application of the 226Ra– 230Th– 234U and 227Ac– 231Pa– 235U radiochronometers to uranium certified reference materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rolison, John M.; Treinen, Kerri C.; McHugh, Kelly C.

Uranium certified reference materials (CRM) issued by New Brunswick Laboratory were subjected to dating using four independent uranium-series radiochronometers. In all cases, there was acceptable agreement between the model ages calculated using the 231Pa– 235U, 230Th– 234U, 227Ac– 235U or 226Ra– 234U radiochronometers and either the certified 230Th– 234U model date (CRM 125-A and CRM U630), or the known purification date (CRM U050 and CRM U100). Finally, the agreement between the four independent radiochronometers establishes these uranium certified reference materials as ideal informal standards for validating dating techniques utilized in nuclear forensic investigations in the absence of standards with certifiedmore » model ages for multiple radiochronometers.« less

Fermentation and Hydrogen Metabolism Affect Uranium Reduction by Clostridia

DOE PAGES

Gao, Weimin; Francis, Arokiasamy J.

2013-01-01

Previously, it has been shown that not only is uranium reduction under fermentation condition common among clostridia species, but also the strains differed in the extent of their capability and the pH of the culture significantly affected uranium(VI) reduction. In this study, using HPLC and GC techniques, metabolic properties of those clostridial strains active in uranium reduction under fermentation conditions have been characterized and their effects on capability variance of uranium reduction discussed. Then, the relationship between hydrogen metabolism and uranium reduction has been further explored and the important role played by hydrogenase in uranium(VI) and iron(III) reduction by clostridiamore » demonstrated. When hydrogen was provided as the headspace gas, uranium(VI) reduction occurred in the presence of whole cells of clostridia. This is in contrast to that of nitrogen as the headspace gas. Without clostridia cells, hydrogen alone could not result in uranium(VI) reduction. In alignment with this observation, it was also found that either copper(II) addition or iron depletion in the medium could compromise uranium reduction by clostridia. In the end, a comprehensive model was proposed to explain uranium reduction by clostridia and its relationship to the overall metabolism especially hydrogen (H 2 ) production.« less

Drowning unconformities: Palaeoenvironmental significance and involvement of global processes

NASA Astrophysics Data System (ADS)

Godet, Alexis

2013-07-01

Drowning unconformities are stratigraphic key surfaces in the history of carbonate platforms. They mostly consist in the deposition of deep marine facies on top of shallow marine limestones. Although large-scale depositional geometries mimic lowstand systems track architecture, these sedimentary turnovers are developed in relation with major sea level rise, inducing an increase in the rate of creation of accommodation space that outpaces the capacity of carbonate to keep up. This so-called paradox of carbonate platform drowning implies that parameters other than purely eustatic fluctuations are involved in the demise of shallow marine ecosystems. Worldwide and at different times during Earth history, in-depth studies of drowning unconformities revealed that changes in nutrient input, clastic delivery, temperature, or a combination of them may be responsible for a decrease in light penetration in the water column and the progressive suffocation and poisoning of photosynthetic carbonate producers. The examination of such case examples from various stratigraphic intervals and palaeogeographical settings thus helps in identifying and hierarchizing potential triggering mechanisms for drowning unconformities. This is complemented by new data from Early Cretaceous successions from the Helvetic Alps. During this time period, the Helvetic carbonate platform developed along the northern Tethyan margin using both photozoan and heterozoan communities. Phases of healthy production were interrupted by several drowning episodes. The latter are marked in the sedimentary record by condensation and associated phosphogenesis and glauconitisation. From the earliest Valanginian to the early to late Barremian, three drowning unconformities reflect the intermittent installation of a more humid climate and subsequent enhanced trophic conditions, which first induced a switch from photozoan to heterozoan communities and then to long-lasting drowning phases. The latter encompass several sea level rise and fall cycles, and may be linked to strengthened upwelling currents. With the return to more oligotrophic conditions during the late Barremian, photozoan, Urgonian-type communities took up again. Their development has been abruptly stopped at the end of the early Aptian by a major emersion phase. The subsequent drowning is documented in various peritethyan areas. This initial crisis is followed by three other drowning phases that ultimately led to the replacement of shallow ecosystems by a deeper marine sedimentation in the Cenomanian. This long-term trend in the evolution of the Helvetic carbonate platform and of other peritethyan ecosystems may have been driven by more global phenomena. In particular, the progressive opening of the northern and equatorial Atlantic may have impacted sea level by creating new oceanic basins. The emplacement of submarine volcanic plateaus may have triggered sea level rise and fertilized deep oceanic waters through hydrothermal processes. Drowning unconformities thus record the interplay of local with long-term processes, and constitute regional sedimentary archives of global phenomena.

Cellular localization of uranium in the renal proximal tubules during acute renal uranium toxicity.

PubMed

Homma-Takeda, Shino; Kitahara, Keisuke; Suzuki, Kyoko; Blyth, Benjamin J; Suya, Noriyoshi; Konishi, Teruaki; Terada, Yasuko; Shimada, Yoshiya

2015-12-01

Renal toxicity is a hallmark of uranium exposure, with uranium accumulating specifically in the S3 segment of the proximal tubules causing tubular damage. As the distribution, concentration and dynamics of accumulated uranium at the cellular level is not well understood, here, we report on high-resolution quantitative in situ measurements by high-energy synchrotron radiation X-ray fluorescence analysis in renal sections from a rat model of uranium-induced acute renal toxicity. One day after subcutaneous administration of uranium acetate to male Wistar rats at a dose of 0.5 mg uranium kg(-1) body weight, uranium concentration in the S3 segment of the proximal tubules was 64.9 ± 18.2 µg g(-1) , sevenfold higher than the mean renal uranium concentration (9.7 ± 2.4 µg g(-1) ). Uranium distributed into the epithelium of the S3 segment of the proximal tubules and highly concentrated uranium (50-fold above mean renal concentration) in micro-regions was found near the nuclei. These uranium levels were maintained up to 8 days post-administration, despite more rapid reductions in mean renal concentration. Two weeks after uranium administration, damaged areas were filled with regenerating tubules and morphological signs of tissue recovery, but areas of high uranium concentration (100-fold above mean renal concentration) were still found in the epithelium of regenerating tubules. These data indicate that site-specific accumulation of uranium in micro-regions of the S3 segment of the proximal tubules and retention of uranium in concentrated areas during recovery are characteristics of uranium behavior in the kidney. Copyright © 2015 John Wiley & Sons, Ltd.

Rapid removal of uranium from aqueous solutions using magnetic Fe3O4@SiO2 composite particles.

PubMed

Fan, Fang-Li; Qin, Zhi; Bai, Jing; Rong, Wei-Dong; Fan, Fu-You; Tian, Wei; Wu, Xiao-Lei; Wang, Yang; Zhao, Liang

2012-04-01

Rapid removal of U(VI) from aqueous solutions was investigated using magnetic Fe(3)O(4)@SiO(2) composite particles as the novel adsorbent. Batch experiments were conducted to study the effects of initial pH, amount of adsorbent, shaking time and initial U(VI) concentrations on uranium sorption efficiency as well as the desorbing of U(VI). The sorption of uranium on Fe(3)O(4)@SiO(2) composite particles was pH-dependent, and the optimal pH was 6.0. In kinetics studies, the sorption equilibrium can be reached within 180 min, and the experimental data were well fitted by the pseudo-second-order model, and the equilibrium sorption capacities calculated by the model were almost the same as those determined by experiments. The Langmuir sorption isotherm model correlates well with the uranium sorption equilibrium data for the concentration range of 20-200 mg/L. The maximum uranium sorption capacity onto magnetic Fe(3)O(4)@SiO(2) composite particles was estimated to be about 52 mg/g at 25 °C. The highest values of uranium desorption (98%) was achieved using 0.01 M HCl as the desorbing agent. Fe(3)O(4)@SiO(2) composite particles showed a good selectivity for uranium from aqueous solution with other interfering cation ions. Present study suggested that magnetic Fe(3)O(4)@SiO(2) composite particles can be used as a potential adsorbent for sorption uranium and also provided a simple, fast separation method for removal of heavy metal ion from aqueous solution. Copyright © 2011 Elsevier Ltd. All rights reserved.

Aftermath of Uranium Ore Processing on Floodplains: Lasting Effects of Uranium on Soil and Microbes

NASA Astrophysics Data System (ADS)

Tang, H.; Boye, K.; Bargar, J.; Fendorf, S. E.

2016-12-01

A former uranium ore processing site located between the Wind River and the Little Wind River near the city of Riverton, Wyoming, has generated a uranium plume in the groundwater within the floodplain. Uranium is toxic and poses a threat to human health. Thus, controlling and containing the spread of uranium will benefit the human population. The primary source of uranium was removed from the processing site, but a uranium plume still exists in the groundwater. Uranium in its reduced form is relatively insoluble in water and therefore is retained in organic rich, anoxic layers in the subsurface. However, with the aid of microbes uranium becomes soluble in water which could expose people and the environment to this toxin, if it enters the groundwater and ultimately the river. In order to better understand the mechanisms controlling uranium behavior in the floodplains, we examined sediments from three sediment cores (soil surface to aquifer). We determined the soil elemental concentrations and measured microbial activity through the use of several instruments (e.g. Elemental Analyzer, X-ray Fluorescence, MicroResp System). Through the data collected, we aim to obtain a better understanding of how the interaction of geochemical factors and microbial metabolism affect uranium mobility. This knowledge will inform models used to predict uranium behavior in response to land use or climate change in floodplain environments.

New Technique for Speciation of Uranium in Sediments Following Acetate-Stimulated Bioremediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2011-06-22

Acetate-stimulated bioremediation is a promising new technique for sequestering toxic uranium contamination from groundwater. The speciation of uranium in sediments after such bioremediation attempts remains unknown as a result of low uranium concentration, and is important to analyzing the stability of sequestered uranium. A new technique was developed for investigating the oxidation state and local molecular structure of uranium from field site sediments using X-Ray Absorption Spectroscopy (XAS), and was implemented at the site of a former uranium mill in Rifle, CO. Glass columns filled with bioactive Rifle sediments were deployed in wells in the contaminated Rifle aquifer and amendedmore » with a hexavalent uranium (U(VI)) stock solution to increase uranium concentration while maintaining field conditions. This sediment was harvested and XAS was utilized to analyze the oxidation state and local molecular structure of the uranium in sediment samples. Extended X-Ray Absorption Fine Structure (EXAFS) data was collected and compared to known uranium spectra to determine the local molecular structure of the uranium in the sediment. Fitting was used to determine that the field site sediments did not contain uraninite (UO{sub 2}), indicating that models based on bioreduction using pure bacterial cultures are not accurate for bioremediation in the field. Stability tests on the monomeric tetravalent uranium (U(IV)) produced by bioremediation are needed in order to assess the efficacy of acetate-stimulation bioremediation.« less

Improving gross count gamma-ray logging in uranium mining with the NGRS probe

NASA Astrophysics Data System (ADS)

Carasco, C.; Pérot, B.; Ma, J.-L.; Toubon, H.; Dubille-Auchère, A.

2018-01-01

AREVA Mines and the Nuclear Measurement Laboratory of CEA Cadarache are collaborating to improve the sensitivity and precision of uranium concentration measurement by means of gamma ray logging. The determination of uranium concentration in boreholes is performed with the Natural Gamma Ray Sonde (NGRS) based on a NaI(Tl) scintillation detector. The total gamma count rate is converted into uranium concentration using a calibration coefficient measured in concrete blocks with known uranium concentration in the AREVA Mines calibration facility located in Bessines, France. Until now, to take into account gamma attenuation in a variety of boreholes diameters, tubing materials, diameters and thicknesses, filling fluid densities and compositions, a semi-empirical formula was used to correct the calibration coefficient measured in Bessines facility. In this work, we propose to use Monte Carlo simulations to improve gamma attenuation corrections. To this purpose, the NGRS probe and the calibration measurements in the standard concrete blocks have been modeled with MCNP computer code. The calibration coefficient determined by simulation, 5.3 s-1.ppmU-1 ± 10%, is in good agreement with the one measured in Bessines, 5.2 s-1.ppmU-1. Based on the validated MCNP model, several parametric studies have been performed. For instance, the rock density and chemical composition proved to have a limited impact on the calibration coefficient. However, gamma self-absorption in uranium leads to a nonlinear relationship between count rate and uranium concentration beyond approximately 1% of uranium weight fraction, the underestimation of the uranium content reaching more than a factor 2.5 for a 50 % uranium weight fraction. Next steps will concern parametric studies with different tubing materials, diameters and thicknesses, as well as different borehole filling fluids representative of real measurement conditions.

Uranium and the Central Nervous System: What Should We Learn from Recent New Tools and Findings?

PubMed

Dinocourt, Céline

2017-01-01

Increasing industrial and military use of uranium has led to environmental pollution, which may result in uranium reaching the brain and causing cerebral dysfunction. A recent literature review has discussed data published over the last 10 years on uranium and its effects on brain function (Dinocourt C, Legrand M, Dublineau I, et al., Toxicology 337:58-71, 2015). New models of uranium exposure during neonatal brain development and the emergence of new technologies (omics and epigenetics) are of value in identifying new specific targets of uranium. Here we review the latest studies of neurogenesis, epigenetics, and metabolic dysfunctions and the identification of new biomarkers used to establish potential pathophysiological states of neurodevelopmental and neurodegenerative diseases.

Genetic approach to reconstruct complex regional geological setting of the Baltic basin in 3D geological model

NASA Astrophysics Data System (ADS)

Popovs, K.; Saks, T.; Ukass, J.; Jatnieks, J.

2012-04-01

Interpretation of geological structures in 3D geological models is a relatively new research topic that is already standardized in many geological branches. Due to its wide practical application, these models are indispensable and become one of the dominant interpretation methods in reducing geological uncertainties in many geology fields. Traditionally, geological concepts complement quantitative as much as qualitative data to obtain a model deemed acceptable, however, available data very often is insufficient and modeling methods primarily focus on spatial data but geological history usually is mostly neglected for the modeling of large sedimentary basins. A need to better integrate the long and often complex geological history and geological knowledge into modeling procedure is very acute to gain geological insight and improve the quality of geological models. During this research, 3D geological model of the Baltic basin (BB) was created. Because of its complex regional geological setting - wide range of the data sources with multiple scales, resolution and density as well as its various source formats, the study area provides a challenge for the 3D geological modeling. In order to create 3D regional geometrical model for the study area algorithmic genetic approach for model geometry reconstruction was applied. The genetic approach is based on the assumption that post-depositional deformation produce no significant change in sedimentary strata volume, assuming that the strata thickness and its length in a cross sectional plane remains unchanged except as a result of erosion. Assuming that the tectonic deformation occurred in sequential cycles and subsequent tectonic stage strata is separated by regional unconformity as is the case of the BB, there is an opportunity for algorithmic approach in reconstructing these conditions by sequentially reconstructing the layer original thickness. Layer thicknesses were sliced along fault lines, where applicable layer thickness was adjusted by taking into account amount of erosion by the presence of the regional unconformities. Borehole data and structural maps of some surfaces were used in creating geological model of the BB. Used approach allowed creating geologically sound geometric model. At first borehole logs were used to reconstruct initial thicknesses of different strata in every tectonic stage, where topography of each strata was obtained sequentially summing thickness to the initial reference surface from structural maps. Thereby each layer reflects the topography and amount of slip along the fault of the overlying layer. Overlying tectonic cycle sequence is implemented into the model structure by using unconformity surface as an initial reference surface. Applied techniques made possible reliably reconstructing and predicting in areas of sparse data layer surface geometry, its thickness distribution and evaluating displacements along the fault planes. Overall results indicate that the used approach has a good potential in development of regional geological models for the sedimentary basins and is valid for spatial interpretation of geological structures, subordinating this process to geological evolution prerequisites. This study is supported by the European Social Fund project No. 2009/0212/1DP/1.1.1.2.0/09/APIA/VIAA/060.

Feasibility Study on the Use of On-line Multivariate Statistical Process Control for Safeguards Applications in Natural Uranium Conversion Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ladd-Lively, Jennifer L

2014-01-01

The objective of this work was to determine the feasibility of using on-line multivariate statistical process control (MSPC) for safeguards applications in natural uranium conversion plants. Multivariate statistical process control is commonly used throughout industry for the detection of faults. For safeguards applications in uranium conversion plants, faults could include the diversion of intermediate products such as uranium dioxide, uranium tetrafluoride, and uranium hexafluoride. This study was limited to a 100 metric ton of uranium (MTU) per year natural uranium conversion plant (NUCP) using the wet solvent extraction method for the purification of uranium ore concentrate. A key component inmore » the multivariate statistical methodology is the Principal Component Analysis (PCA) approach for the analysis of data, development of the base case model, and evaluation of future operations. The PCA approach was implemented through the use of singular value decomposition of the data matrix where the data matrix represents normal operation of the plant. Component mole balances were used to model each of the process units in the NUCP. However, this approach could be applied to any data set. The monitoring framework developed in this research could be used to determine whether or not a diversion of material has occurred at an NUCP as part of an International Atomic Energy Agency (IAEA) safeguards system. This approach can be used to identify the key monitoring locations, as well as locations where monitoring is unimportant. Detection limits at the key monitoring locations can also be established using this technique. Several faulty scenarios were developed to test the monitoring framework after the base case or normal operating conditions of the PCA model were established. In all of the scenarios, the monitoring framework was able to detect the fault. Overall this study was successful at meeting the stated objective.« less

Gamma-ray spectroscopy measurements and simulations for uranium mining

NASA Astrophysics Data System (ADS)

Marchais, T.; Pérot, B.; Carasco, C.; Allinei, P.-G.; Chaussonnet, P.; Ma, J.-L.; Toubon, H.

2018-01-01

AREVA Mines and the Nuclear Measurement Laboratory of CEA Cadarache are collaborating to improve the sensitivity and precision of uranium concentration evaluation by means of gamma measurements. This paper reports gamma-ray spectra, recorded with a high-purity coaxial germanium detector, on standard cement blocks with increasing uranium content, and the corresponding MCNP simulations. The detailed MCNP model of the detector and experimental setup has been validated by calculation vs. experiment comparisons. An optimization of the detector MCNP model is presented in this paper, as well as a comparison of different nuclear data libraries to explain missing or exceeding peaks in the simulation. Energy shifts observed between the fluorescence X-rays produced by MCNP and atomic data are also investigated. The qualified numerical model will be used in further studies to develop new gamma spectroscopy approaches aiming at reducing acquisition times, especially for ore samples with low uranium content.

Estimating terrestrial uranium and thorium by antineutrino flux measurements.

PubMed

Dye, Stephen T; Guillian, Eugene H

2008-01-08

Uranium and thorium within the Earth produce a major portion of terrestrial heat along with a measurable flux of electron antineutrinos. These elements are key components in geophysical and geochemical models. Their quantity and distribution drive the dynamics, define the thermal history, and are a consequence of the differentiation of the Earth. Knowledge of uranium and thorium concentrations in geological reservoirs relies largely on geochemical model calculations. This article describes the methods and criteria to experimentally determine average concentrations of uranium and thorium in the continental crust and in the mantle by using site-specific measurements of the terrestrial antineutrino flux. Optimal, model-independent determinations involve significant exposures of antineutrino detectors remote from nuclear reactors at both a midcontinental and a midoceanic site. This would require major, new antineutrino detection projects. The results of such projects could yield a greatly improved understanding of the deep interior of the Earth.

Estimating terrestrial uranium and thorium by antineutrino flux measurements

PubMed Central

Dye, Stephen T.; Guillian, Eugene H.

2008-01-01

Uranium and thorium within the Earth produce a major portion of terrestrial heat along with a measurable flux of electron antineutrinos. These elements are key components in geophysical and geochemical models. Their quantity and distribution drive the dynamics, define the thermal history, and are a consequence of the differentiation of the Earth. Knowledge of uranium and thorium concentrations in geological reservoirs relies largely on geochemical model calculations. This article describes the methods and criteria to experimentally determine average concentrations of uranium and thorium in the continental crust and in the mantle by using site-specific measurements of the terrestrial antineutrino flux. Optimal, model-independent determinations involve significant exposures of antineutrino detectors remote from nuclear reactors at both a midcontinental and a midoceanic site. This would require major, new antineutrino detection projects. The results of such projects could yield a greatly improved understanding of the deep interior of the Earth. PMID:18172211

Mixture Model for Determination of Shock Equation of State

DTIC Science & Technology

2012-07-25

not considered in this paper. III. COMPARISON WITH EXPERIMENTAL DATA A. Two-constituent composites 1. Uranium- rhodium composite Uranium- rhodium (U...sound speed, Co, and S were determined from linear least squares fit to the available data22 as shown in Figs. 1(a) and 1(b) for uranium and rhodium ...overpredicts the experimental data, with an average deviation, dUs,/Us of 0.05, shown in Fig. 2(b). The linear fits for uranium and rhodium are shown for

Upper Cretaceous and Lower Jurassic strata in shallow cores on the Chukchi Shelf, Arctic Alaska: Chapter C in Studies by the U.S. Geological Survey in Alaska, vol. 15

USGS Publications Warehouse

Houseknecht, David W.; Craddock, William H.; Lease, Richard O.

2016-02-12

Shallow cores collected in the 1980s on the Chukchi Shelf of western Arctic Alaska sampled pre-Cenozoic strata whose presence, age, and character are poorly known across the region. Five cores from the Herald Arch foreland contain Cenomanian to Coniacian strata, as documented by biostratigraphy, geochronology, and thermochronology. Shallow seismic reflection data collected during the 1970s and 1980s show that these Upper Cretaceous strata are truncated near the seafloor by subtle angular unconformities, including the Paleogene mid-Brookian unconformity in one core and the Pliocene-Pleistocene unconformity in four cores. Sedimentary structures and lithofacies suggest that Upper Cretaceous strata were deposited in a low accommodation setting that ranged from low-lying coastal plain (nonmarine) to muddy, shallow-marine environments near shore. These observations, together with sparse evidence from the adjacent western North Slope, suggest that Upper Cretaceous strata likely were deposited across all of Arctic Alaska.A sixth core from the Herald Arch contains lower Toarcian marine strata, indicated by biostratigraphy, truncated by a Neogene or younger unconformity. These Lower Jurassic strata evidently were deposited south of the arch, buried structurally to high levels of thermal maturity during the Early Cretaceous, and uplifted on the Herald thrust-fault system during the mid to Late Cretaceous. These interpretations are based on regional stratigraphy and apatite fission-track data reported in a complementary report and are corroborated by the presence of recycled palynomorphs of Early Jurassic age and high thermal maturity found in Upper Cretaceous strata in two of the foreland cores. This dataset provides evidence that uplift and exhumation of the Herald thrust belt provided sediment to the foreland during the Late Cretaceous.

Stratigraphy of the Neogene Sahabi units in the Sirt Basin, northeast Libya

NASA Astrophysics Data System (ADS)

El-Shawaihdi, M. H.; Mozley, P. S.; Boaz, N. T.; Salloum, F.; Pavlakis, P.; Muftah, A.; Triantaphyllou, M.

2016-06-01

A revision of the nomenclature of lithostratigraphic units of Neogene strata at As Sahabi, northeast Libya, is presented, based on new fieldwork conducted during 2006-2008. The Sahabi units are correlated across the Ajdabya Sheet (NH 34-6) in northeastern Libya. Major conclusions are: (1) Miocene (Langhian through Messinian) strata are predominantly carbonate and should be referred to as formation "M"; (2) A local unconformity of Miocene (early Messinian) age overlies strata of the formation "M"; (3) This unconformity is overlain by Messinian gypsiferous sand and mud (formerly formation "P" and partially member "T"), which are designated as the "lower member" (gypsiferous) of the Sahabi Formation; (4) The "lower member" is overlain by sand and mud of late Messinian age (formerly partially member "T" and members "U1", "UD", and "U2") in a generally fining-upwards sequence, and are designated as the "upper member" (non-gypsiferous) of the Sahabi Formation; (5) The latest Miocene sand and mud of the "upper member" are capped by an unconformity that is correlated with the regression and desiccation of the Mediterranean Sea during the Messinian Salinity Crisis and with Eosahabi Channel cutting; (6) The unconformity is overlain by Pliocene medium, coarse, and pebbly sands, which are referred to as the Qarat Weddah Formation (formerly Garet Uedda Formation); (7) The Pliocene sands of Qarat Weddah Formation are overlain by carbonate soil (calcrete) of Late Pliocene age, which is referred to as formation "Z" (formerly member "Z"). The major outcome of this study is a revised stratigraphic description and nomenclature of the Sahabi units that helps to provide a formal and unified context for understanding paleontological discoveries in northeastern Libya, which will serve to facilitate a broader correlation of the Sahabi units with their equivalents elsewhere in Africa and in Europe and Asia.

The Miocene-Pliocene unconformity in the North Betic corridor. The expression of the reflector "M" in the Atlantic

NASA Astrophysics Data System (ADS)

Sierro, Francisco J.; Ledesma, Santiago; A: Flores, Jose; Garcia-Castellanos, Daniel; Hernandez-Molina, Javier

2014-05-01

The Miocene Pliocene boundary is associated in the Mediterranean to a major flooding of Atlantic water that terminated with the Messinian salinity crisis. In many seismic profiles all over the Mediterranean margins this event is linked to an erosion surface that separates the Messinian evaporitic units from the overlying open marine Pliocene sediments. This unconformity originally identified as reflector "M" can be traced to the deep basins as a paraconformity / local erosional surface that has been usually named as Horizon M. This erosive surface in Mediterranean continental margins has been linked to a pronounced drawdown of base level triggered during the Messinian. In consequence, this unconformity should be only expressed in the Mediterranean. However, a significant unconformity has been recognized in the Guadalquivir basin and in the Gulf of Cadiz in the Atlantic side of Iberia that is identified as a Messinian canyon deepening towards the Atlantic. Recently, the cyclostratigraphic and biostratigraphic analyses of various logs recovered by different oil and gas exploration companies over the last decades allowed us to accurately date this major discontinuity in the Guadalquivir basin and the Gulf of Cadiz, as well as to compare sedimentary cycles in the Atlantic with those of the Mediterranean. The astronomical tuning of these cycles unambiguously links this discontinuity in the Atlantic with the Miocene Pliocene boundary, raising important questions about the origin of this major event. We explore the potential origins for this discontinuity, including the tectonic vertical motions of the Betic-Guadalquivir system, or the presence of a seaway undergoing intense bottom-current circulation between the Mediterranean and the Atlantic.

Characteristics of uranium biosorption from aqueous solutions on fungus Pleurotus ostreatus.

PubMed

Zhao, Changsong; Liu, Jun; Tu, Hong; Li, Feize; Li, Xiyang; Yang, Jijun; Liao, Jiali; Yang, Yuanyou; Liu, Ning; Sun, Qun

2016-12-01

Uranium(VI) biosorption from aqueous solutions was investigated in batch studies by using fungus Pleurotus ostreatus biomass. The optimal biosorption conditions were examined by investigating the reaction time, biomass dosage, pH, temperature, and uranium initial concentration. The interaction between fungus biomass and uranium was confirmed using Fourier transformed infrared (FT-IR), scanning electronic microscopy energy dispersive X-ray (SEM-EDX), and X-ray photoelectron spectroscopy (XPS) analysis. Results exhibited that the maximum biosorption capacity of uranium on P. ostreatus was 19.95 ± 1.17 mg/g at pH 4.0. Carboxylic, amine, as well as hydroxyl groups were involved in uranium biosorption according to FT-IR analysis. The pseudo-second-order model properly evaluated the U(VI) biosorption on fungus P. ostreatus biomass. The Langmuir equation provided better fitting in comparison with Freundlich isotherm models. The obtained thermodynamic parameters suggested that biosorption is feasible, endothermic, and spontaneous. SEM-EDX and XPS were additionally conducted to comprehend the biosorption process that could be described as a complex process involving several mechanisms of physical adsorption, chemisorptions, and ion exchange. Results obtained from this work indicated that fungus P. ostreatus biomass can be used as potential biosorbent to eliminate uranium or other radionuclides from aqueous solutions.

A top-down assessment of energy, water and land use in uranium mining, milling, and refining

DOE Office of Scientific and Technical Information (OSTI.GOV)

E. Schneider; B. Carlsen; E. Tavrides

2013-11-01

Land, water and energy use are key measures of the sustainability of uranium production into the future. As the most attractive, accessible deposits are mined out, future discoveries may prove to be significantly, perhaps unsustainably, more intensive consumers of environmental resources. A number of previous attempts have been made to provide empirical relationships connecting these environmental impact metrics to process variables such as stripping ratio and ore grade. These earlier attempts were often constrained by a lack of real world data and perform poorly when compared against data from modern operations. This paper conditions new empirical models of energy, watermore » and land use in uranium mining, milling, and refining on contemporary data reported by operating mines. It shows that, at present, direct energy use from uranium production represents less than 1% of the electrical energy produced by the once-through fuel cycle. Projections of future energy intensity from uranium production are also possible by coupling the empirical models with estimates of uranium crustal abundance, characteristics of new discoveries, and demand. The projections show that even for the most pessimistic of scenarios considered, by 2100, the direct energy use from uranium production represents less than 3% of the electrical energy produced by the contemporary once-through fuel cycle.« less

High Useful Yield and Isotopic Analysis of Uranium by Resonance Ionization Mass Spectrometry

DOE PAGES

Savina, Michael R.; Isselhardt, Brett H.; Kucher, Andrew; ...

2017-05-09

Useful yields from resonance ionization mass spectrometry can be extremely high compared to other mass spectrometry techniques, but uranium analysis shows strong matrix effects arising from the tendency of uranium to form strongly bound oxide molecules that do not dissociate appreciably on energetic ion bombardment. Here, we demonstrate a useful yield of 24% for metallic uranium. Modeling the laser ionization and ion transmission processes shows that the high useful yield is attributable to a high ion fraction achieved by resonance ionization. We quantify the reduction of uranium oxide surface layers by Ar + and Ga + sputtering. The useful yieldmore » for uranium atoms from a uranium dioxide matrix is 0.4% and rises to 2% when the surface is in sputter equilibrium with the ion beam. The lower useful yield from the oxide is almost entirely due to uranium oxide molecules reducing the neutral atom content of the sputtered flux. We also demonstrate rapid isotopic analysis of solid uranium oxide at a precision of <0.5% relative standard deviation using relatively broadband lasers to mitigate spectroscopic fractionation.« less

High Useful Yield and Isotopic Analysis of Uranium by Resonance Ionization Mass Spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Savina, Michael R.; Isselhardt, Brett H.; Kucher, Andrew

Useful yields from resonance ionization mass spectrometry can be extremely high compared to other mass spectrometry techniques, but uranium analysis shows strong matrix effects arising from the tendency of uranium to form strongly bound oxide molecules that do not dissociate appreciably on energetic ion bombardment. Here, we demonstrate a useful yield of 24% for metallic uranium. Modeling the laser ionization and ion transmission processes shows that the high useful yield is attributable to a high ion fraction achieved by resonance ionization. We quantify the reduction of uranium oxide surface layers by Ar + and Ga + sputtering. The useful yieldmore » for uranium atoms from a uranium dioxide matrix is 0.4% and rises to 2% when the surface is in sputter equilibrium with the ion beam. The lower useful yield from the oxide is almost entirely due to uranium oxide molecules reducing the neutral atom content of the sputtered flux. We also demonstrate rapid isotopic analysis of solid uranium oxide at a precision of <0.5% relative standard deviation using relatively broadband lasers to mitigate spectroscopic fractionation.« less

Molecular dynamics analysis of diffusion of uranium and oxygen ions in uranium dioxide

NASA Astrophysics Data System (ADS)

Arima, T.; Yoshida, K.; Idemitsu, K.; Inagaki, Y.; Sato, I.

2010-03-01

Diffusion behaviours of oxygen and uranium were evaluated for bulk and grain-boundaries of uranium dioxide using the molecular dynamics (MD) simulation. It elucidated that oxygen behaved like liquid in superionic state at high temperatures and migrated on sub-lattice sites accompanying formation of lattice defects such as Frenkel defects at middle temperatures. Formation energies of Frenkel and Shottky defects were compared to literature data, and migration energies of oxygen and uranium were estimated by introducing vacancies into the supercell. For grain-boundaries (GB) modelled by the coincidence-site lattice theory, MD calculations showed that GB energy and diffusivities of oxygen and uranium increased with the misorientation angle. By analysing GB structures such as pair-correlation functions, it also showed that the disordered phase was observed for uranium as well as oxygen in GBs especially for a large misorientation angle such as S5 GB. Hence, GB diffusion was much larger than bulk diffusion for oxygen and uranium.

Hydrogeology of an ancient arid closed basin: implications for tabular sandstone-hosted uranium deposits

USGS Publications Warehouse

Sanford, R.F.

1990-01-01

Hydrogeologic modeling shows that tabular-type uranium deposits in the Grants uranium region of the San Juan basin, New Mexico, formed in zones of ascending and discharging regional ground-water flow. The association of either lacustrine mudstone or actively subsiding structures and uranium deposits can best be explained by the occurrence of lakes at topographic depressions where ground water having different sources and compositions is likely to converge, mix, and discharge. Ascending and discharging flow also explains the association of uranium deposits with underlying evaporites and suggests a brine interface. The simulations contradict previous suggestions that ground water moved downward in the mudflat. -Author

A two-dimensional, finite-difference model of the oxidation of a uranium carbide fuel pellet

NASA Astrophysics Data System (ADS)

Shepherd, James; Fairweather, Michael; Hanson, Bruce C.; Heggs, Peter J.

2015-12-01

The oxidation of spent uranium carbide fuel, a candidate fuel for Generation IV nuclear reactors, is an important process in its potential reprocessing cycle. However, the oxidation of uranium carbide in air is highly exothermic. A model has therefore been developed to predict the temperature rise, as well as other useful information such as reaction completion times, under different reaction conditions in order to help in deriving safe oxidation conditions. Finite difference-methods are used to model the heat and mass transfer processes occurring during the reaction in two dimensions and are coupled to kinetics found in the literature.

Adsorption of uranium(VI) to manganese oxides: X-ray absorption spectroscopy and surface complexation modeling.

PubMed

Wang, Zimeng; Lee, Sung-Woo; Catalano, Jeffrey G; Lezama-Pacheco, Juan S; Bargar, John R; Tebo, Bradley M; Giammar, Daniel E

2013-01-15

The mobility of hexavalent uranium in soil and groundwater is strongly governed by adsorption to mineral surfaces. As strong naturally occurring adsorbents, manganese oxides may significantly influence the fate and transport of uranium. Models for U(VI) adsorption over a broad range of chemical conditions can improve predictive capabilities for uranium transport in the subsurface. This study integrated batch experiments of U(VI) adsorption to synthetic and biogenic MnO(2), surface complexation modeling, ζ-potential analysis, and molecular-scale characterization of adsorbed U(VI) with extended X-ray absorption fine structure (EXAFS) spectroscopy. The surface complexation model included inner-sphere monodentate and bidentate surface complexes and a ternary uranyl-carbonato surface complex, which was consistent with the EXAFS analysis. The model could successfully simulate adsorption results over a broad range of pH and dissolved inorganic carbon concentrations. U(VI) adsorption to synthetic δ-MnO(2) appears to be stronger than to biogenic MnO(2), and the differences in adsorption affinity and capacity are not associated with any substantial difference in U(VI) coordination.

Factoring uncertainty into restoration modeling of in-situ leach uranium mines

USGS Publications Warehouse

Johnson, Raymond H.; Friedel, Michael J.

2009-01-01

Postmining restoration is one of the greatest concerns for uranium in-situ leach (ISL) mining operations. The ISL-affected aquifer needs to be returned to conditions specified in the mining permit (either premining or other specified conditions). When uranium ISL operations are completed, postmining restoration is usually achieved by injecting reducing agents into the mined zone. The objective of this process is to restore the aquifer to premining conditions by reducing the solubility of uranium and other metals in the ground water. Reactive transport modeling is a potentially useful method for simulating the effectiveness of proposed restoration techniques. While reactive transport models can be useful, they are a simplification of reality that introduces uncertainty through the model conceptualization, parameterization, and calibration processes. For this reason, quantifying the uncertainty in simulated temporal and spatial hydrogeochemistry is important for postremedial risk evaluation of metal concentrations and mobility. Quantifying the range of uncertainty in key predictions (such as uranium concentrations at a specific location) can be achieved using forward Monte Carlo or other inverse modeling techniques (trial-and-error parameter sensitivity, calibration constrained Monte Carlo). These techniques provide simulated values of metal concentrations at specified locations that can be presented as nonlinear uncertainty limits or probability density functions. Decisionmakers can use these results to better evaluate environmental risk as future metal concentrations with a limited range of possibilities, based on a scientific evaluation of uncertainty.

Elevated Uranium in Aquifers of the Jacobsville Sandstone

NASA Astrophysics Data System (ADS)

Sherman, H.; Gierke, J.

2003-12-01

The EPA has announced a new standard for uranium in drinking water of 30 parts per billion (ppb). This maximum contaminant level (MCL) takes effect for community water supplies December 2003. The EPA's ruling has heightened awareness among residential well owners that uranium in drinking water may increase the risk of kidney disease and cancer and has created a need for a quantified, scientific understanding of the occurrence and distribution of uranium isotopes in aquifers. The authors are investigating the occurrence of elevated uranium in northern Michigan aquifers of the Middle Proterozoic Jacobsville sandstone, a red to mottled sequence of sandstones, conglomerates, siltstones and shales deposited as basin fill in the 1.1 Ga Midcontinent rift. Approximately 25% of 300 well water samples tested for isotopic uranium have concentrations above the MCL. Elevated uranium occurrences are distributed throughout the Jacobsville sandstone aquifers stretching across Michigan's Upper Peninsula. However, there is significant variation in well water uranium concentrations (from 0.01 to 190 ppb) and neighboring wells do not necessarily have similar concentrations. The authors are investigating hydrogeologic controls on ground water uranium concentrations in the Jacobsville sandstone, e.g. variations in lithology, mineralogy, groundwater residence time and geochemistry. Approximately 2000' of Jacobsville core from the Amoco St. Amour well was examined in conjunction with the spectral gamma ray log run in the borehole. Spikes in equivalent uranium (eU) concentration from the log are frequently associated with clay and heavy mineral layers in the sandstone core. The lithology and mineralogy of these layers will be determined by analysis of thin sections and x-ray diffraction. A portable spectrometer, model GRS-2000/BL, will be used on the sandstone cliffs along Lake Superior to characterize depositional and lithologic facies of the Jacobsville sandstone in terms of concentrations and ratios of eU, eTh and K. Equipped with borehole accessories, the spectrometer will be used to log residential drinking wells to determine a relationship between the uranium concentration of well water and the eU concentration in the sandstone. Tritium/helium-3 dating will be used to determine whether ground water uranium concentrations increase with residence time. PHREEQCI will be used to model dominate aqueous species of uranium and saturation indices of uranium minerals.

Newburg-South Westhope oil fields, North Dakota

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marafi, H.

1972-01-01

The Newburg and South Westhope oil fields, located in Bottineau County, North Dak., in the NE. part of the Williston Basin, are excellent examples of stratigraphic traps, although structural elements are involved in trapping of the accumulations. The oil is produced from 2 adjacent zones separated by a major unconformity, and they are considered to be a common reservoir. The productive units are the ''Ratcliffe'' interval of the Mississippian Charles Formation and the Saude Member of the Triassic Spearfish Formation. Post-Paleozoic migration of the oil is indicated because, even though the Ratcliffe was exposed to considerable erosion, it is productivemore » at the unconformity.« less

Influence of uranium hydride oxidation on uranium metal behaviour

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patel, N.; Hambley, D.; Clarke, S.A.

2013-07-01

This work addresses concerns that the rapid, exothermic oxidation of active uranium hydride in air could stimulate an exothermic reaction (burning) involving any adjacent uranium metal, so as to increase the potential hazard arising from a hydride reaction. The effect of the thermal reaction of active uranium hydride, especially in contact with uranium metal, does not increase in proportion with hydride mass, particularly when considering large quantities of hydride. Whether uranium metal continues to burn in the long term is a function of the uranium metal and its surroundings. The source of the initial heat input to the uranium, ifmore » sufficient to cause ignition, is not important. Sustained burning of uranium requires the rate of heat generation to be sufficient to offset the total rate of heat loss so as to maintain an elevated temperature. For dense uranium, this is very difficult to achieve in naturally occurring circumstances. Areas of the uranium surface can lose heat but not generate heat. Heat can be lost by conduction, through contact with other materials, and by convection and radiation, e.g. from areas where the uranium surface is covered with a layer of oxidised material, such as burned-out hydride or from fuel cladding. These rates of heat loss are highly significant in relation to the rate of heat generation by sustained oxidation of uranium in air. Finite volume modelling has been used to examine the behaviour of a magnesium-clad uranium metal fuel element within a bottle surrounded by other un-bottled fuel elements. In the event that the bottle is breached, suddenly, in air, it can be concluded that the bulk uranium metal oxidation reaction will not reach a self-sustaining level and the mass of uranium oxidised will likely to be small in relation to mass of uranium hydride oxidised. (authors)« less

3D seismic investigation of the structural and stratigraphic characteristics of the Pagasa Wedge, Southwest Palawan Basin, Philippines, and their tectonic implications

NASA Astrophysics Data System (ADS)

Ilao, Kimberly A.; Morley, Christopher K.; Aurelio, Mario A.

2018-04-01

The Pagasa Wedge is a poorly imaged deepwater orogenic wedge that has been variously interpreted as representing an accretionary prism, a former accretionary prism modified by thrusting onto a thinned continental margin, and a gravity-driven fold-thrust belt. This study, using 2D and 3D seismic data, together with well information indicates that at least the external part of the wedge is dominantly composed of mass transport complexes, capped by syn-kinematic sediments that have thrusts and normal faults superimposed upon them. Drilling shows that despite stratigraphic repetition of Eocene Middle Miocene units, there is stratigraphic omission of Oligocene and Early Miocene units. This absence suggests that mass transport processes have introduced the Eocene section into the wedge rather than tectonic thrusting. The accretionary prism stage (Oligocene) of the Central Palawan Ophiolite history appears to be marked by predominantly north-vergent deformation. The Deep Regional Unconformity (∼17 Ma) likely indicates the approximate time when obduction ceased in Palawan. The Pagasa Wedge is a late-stage product of the convergence history that was active in its final phase sometime above the top of the Nido Limestone (∼16 Ma) and the base of the Tabon Limestone in the Aboabo-A1X well (∼9 Ma). The top of the wedge is traditionally associated with the Middle Miocene Unconformity (MMU), However the presence of multiple unconformities, diachronous formation tops, local tectonic unconformities and regional diachronous events (e.g. migrating forebulges) all suggest simply giving a single age (or assigning a single unconformity, such as the MMU as defining the top of the Pagasa Wedge is inappropriate. The overall NE-SW trend of the wedge, and the dominant NW transport of structures within the wedge diverge from the more northerly transport direction determined from outcrops in Palawan, and also from the Nido Limestone in the SW part of the Pagasa Wedge. Possibly this NW transport direction is more related to gravity-driven structures responding to uplift of NE-SW Dangerous Grounds margin during the Middle Miocene (related to slab breakoff?) than it is to thrusting rooted in a plate boundary. The final modification of the wedge occurred when the effects of compression deformation on the wedge had largely ended, but gravity processes (in particular mass transport and normal faulting) still operated.

Statistical analysis and isotherm study of uranium biosorption by Padina sp. algae biomass.

PubMed

Khani, Mohammad Hassan

2011-06-01

The application of response surface methodology is presented for optimizing the removal of U ions from aqueous solutions using Padina sp., a brown marine algal biomass. Box-Wilson central composite design was employed to assess individual and interactive effects of the four main parameters (pH and initial uranium concentration in solutions, contact time and temperature) on uranium uptake. Response surface analysis showed that the data were adequately fitted to second-order polynomial model. Analysis of variance showed a high coefficient of determination value (R (2)=0.9746) and satisfactory second-order regression model was derived. The optimum pH and initial uranium concentration in solutions, contact time and temperature were found to be 4.07, 778.48 mg/l, 74.31 min, and 37.47°C, respectively. Maximized uranium uptake was predicted and experimentally validated. The equilibrium data for biosorption of U onto the Padina sp. were well represented by the Langmuir isotherm, giving maximum monolayer adsorption capacity as high as 376.73 mg/g.

Why Nuclear Forensics Needs New Plasma Chemistry Data

NASA Astrophysics Data System (ADS)

Rose, T.; Armstrong, M.; Chernov, A.; Crowhurst, J.; Dai, Z.; Knight, K.; Koroglu, B.; Radousky, H.; Stavrou, E.; Weisz, D.; Zaug, J.; Azer, M.; Finko, M.; Curreli, D.

2016-10-01

The mechanisms that control the distribution of radionuclides in fallout after a nuclear detonation are not adequately constrained. Current capabilities for assessing post-detonation scenarios often rely on empirical observations and approximations. Deeper insight into chemical condensation requires a coupled experimental, theoretical, and modeling approach. The behavior of uranium during plasma condensation is perplexing. Two independent methods are being developed to investigate gas phase uranium chemistry and speciation during plasma condensation: (1) laser-induced breakdown spectroscopy and (2) a unique steady-state ICP flow reactor. Both methods use laser absorption spectroscopy to obtain in situ data for vapor phase molecular species as they form. We are developing a kinetic model to describe the relative abundance of uranium species in the evolving plasma. Characterization of the uranium-oxygen system will be followed by other chemical components, including `carrier' materials such as silica. The goal is to develop a semi-empirical model to describe the chemical fractionation of uranium during fallout formation. Prepared by LLNL under Contract DE-AC52-07NA27344. This project was sponsored in part by the Department of the Defense, Defense Threat Reduction Agency, under Grant Number HDTRA1-16-1-0020.

A Point Kinetics Model for Estimating Neutron Multiplication of Bare Uranium Metal in Tagged Neutron Measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tweardy, Matthew C.; McConchie, Seth; Hayward, Jason P.

An extension of the point kinetics model is developed in this paper to describe the neutron multiplicity response of a bare uranium object under interrogation by an associated particle imaging deuterium-tritium (D-T) measurement system. This extended model is used to estimate the total neutron multiplication of the uranium. Both MCNPX-PoliMi simulations and data from active interrogation measurements of highly enriched and depleted uranium geometries are used to evaluate the potential of this method and to identify the sources of systematic error. The detection efficiency correction for measured coincidence response is identified as a large source of systematic error. If themore » detection process is not considered, results suggest that the method can estimate total multiplication to within 13% of the simulated value. Values for multiplicity constants in the point kinetics equations are sensitive to enrichment due to (n, xn) interactions by D-T neutrons and can introduce another significant source of systematic bias. This can theoretically be corrected if isotopic composition is known a priori. Finally, the spatial dependence of multiplication is also suspected of introducing further systematic bias for high multiplication uranium objects.« less

A Point Kinetics Model for Estimating Neutron Multiplication of Bare Uranium Metal in Tagged Neutron Measurements

DOE PAGES

Tweardy, Matthew C.; McConchie, Seth; Hayward, Jason P.

2017-06-13

An extension of the point kinetics model is developed in this paper to describe the neutron multiplicity response of a bare uranium object under interrogation by an associated particle imaging deuterium-tritium (D-T) measurement system. This extended model is used to estimate the total neutron multiplication of the uranium. Both MCNPX-PoliMi simulations and data from active interrogation measurements of highly enriched and depleted uranium geometries are used to evaluate the potential of this method and to identify the sources of systematic error. The detection efficiency correction for measured coincidence response is identified as a large source of systematic error. If themore » detection process is not considered, results suggest that the method can estimate total multiplication to within 13% of the simulated value. Values for multiplicity constants in the point kinetics equations are sensitive to enrichment due to (n, xn) interactions by D-T neutrons and can introduce another significant source of systematic bias. This can theoretically be corrected if isotopic composition is known a priori. Finally, the spatial dependence of multiplication is also suspected of introducing further systematic bias for high multiplication uranium objects.« less

Statistical sampling of the distribution of uranium deposits using geologic/geographic clusters

USGS Publications Warehouse

Finch, W.I.; Grundy, W.D.; Pierson, C.T.

1992-01-01

The concept of geologic/geographic clusters was developed particularly to study grade and tonnage models for sandstone-type uranium deposits. A cluster is a grouping of mined as well as unmined uranium occurrences within an arbitrary area about 8 km across. A cluster is a statistical sample that will reflect accurately the distribution of uranium in large regions relative to various geologic and geographic features. The example of the Colorado Plateau Uranium Province reveals that only 3 percent of the total number of clusters is in the largest tonnage-size category, greater than 10,000 short tons U3O8, and that 80 percent of the clusters are hosted by Triassic and Jurassic rocks. The distributions of grade and tonnage for clusters in the Powder River Basin show a wide variation; the grade distribution is highly variable, reflecting a difference between roll-front deposits and concretionary deposits, and the Basin contains about half the number in the greater-than-10,000 tonnage-size class as does the Colorado Plateau, even though it is much smaller. The grade and tonnage models should prove useful in finding the richest and largest uranium deposits. ?? 1992 Oxford University Press.

Redox Roll-Front Mobilization of Geogenic Uranium by Nitrate Input into Aquifers: Risks for Groundwater Resources.

PubMed

van Berk, Wolfgang; Fu, Yunjiao

2017-01-03

Redox conditions are seen as the key to controlling aqueous uranium concentrations (cU (aq) ). Groundwater data collected by a state-wide groundwater quality monitoring study in Mecklenburg-Western Pomerania (Germany) reveal peak cU (aq) up to 75 μg L -1 but low background uranium concentrations (median cU (aq) < 0.5 μg L -1 ). To characterize the hydrogeochemical processes causing such groundwater contamination by peak cU (aq) , we reanalyzed measured redox potentials and total concentrations of aqueous uranium, nitrate, and sulfate species in groundwater together with their distribution across the aquifer depth and performed semigeneric 2D reactive mass transport modeling which is based on chemical thermodynamics. The combined interpretation of modeling results and measured data reveals that high cU (aq) and its depth-specific distribution depending on redox conditions is a result of a nitrate-triggered roll-front mobilization of geogenic uranium in the studied aquifers which are unaffected by nuclear activities. The modeling results show that groundwater recharge containing (fertilizer-derived) nitrate drives the redox shift from originally reducing toward oxidizing environments, when nitrate input has consumed the reducing capacity of the aquifers, which is present as pyrite, degradable organic carbon, and geogenic U(IV) minerals. This redox shift controls the uranium roll-front mobilization and results in high cU (aq) within the redoxcline. Moreover, the modeling results indicate that peak cU (aq) occurring at this redox front increase along with the temporal progress of such redox conversion within the aquifer.

Lung Cancer Mortality (1950–1999) among Eldorado Uranium Workers: A Comparison of Models of Carcinogenesis and Empirical Excess Risk Models

PubMed Central

Eidemüller, Markus; Jacob, Peter; Lane, Rachel S. D.; Frost, Stanley E.; Zablotska, Lydia B.

2012-01-01

Lung cancer mortality after exposure to radon decay products (RDP) among 16,236 male Eldorado uranium workers was analyzed. Male workers from the Beaverlodge and Port Radium uranium mines and the Port Hope radium and uranium refinery and processing facility who were first employed between 1932 and 1980 were followed up from 1950 to 1999. A total of 618 lung cancer deaths were observed. The analysis compared the results of the biologically-based two-stage clonal expansion (TSCE) model to the empirical excess risk model. The spontaneous clonal expansion rate of pre-malignant cells was reduced at older ages under the assumptions of the TSCE model. Exposure to RDP was associated with increase in the clonal expansion rate during exposure but not afterwards. The increase was stronger for lower exposure rates. A radiation-induced bystander effect could be a possible explanation for such an exposure response. Results on excess risks were compared to a linear dose-response parametric excess risk model with attained age, time since exposure and dose rate as effect modifiers. In all models the excess relative risk decreased with increasing attained age, increasing time since exposure and increasing exposure rate. Large model uncertainties were found in particular for small exposure rates. PMID:22936975

First-principles study on oxidation effects in uranium oxides and high-pressure high-temperature behavior of point defects in uranium dioxide

NASA Astrophysics Data System (ADS)

Geng, Hua Y.; Song, Hong X.; Jin, K.; Xiang, S. K.; Wu, Q.

2011-11-01

Formation Gibbs free energy of point defects and oxygen clusters in uranium dioxide at high-pressure high-temperature conditions are calculated from first principles, using the LSDA+U approach for the electronic structure and the Debye model for the lattice vibrations. The phonon contribution on Frenkel pairs is found to be notable, whereas it is negligible for the Schottky defect. Hydrostatic compression changes the formation energies drastically, making defect concentrations depend more sensitively on pressure. Calculations show that, if no oxygen clusters are considered, uranium vacancy becomes predominant in overstoichiometric UO2 with the aid of the contribution from lattice vibrations, while compression favors oxygen defects and suppresses uranium vacancy greatly. At ambient pressure, however, the experimental observation of predominant oxygen defects in this regime can be reproduced only in a form of cuboctahedral clusters, underlining the importance of defect clustering in UO2+x. Making use of the point defect model, an equation of state for nonstoichiometric oxides is established, which is then applied to describe the shock Hugoniot of UO2+x. Furthermore, the oxidization and compression behavior of uranium monoxide, triuranium octoxide, uranium trioxide, and a series of defective UO2 at 0 K are investigated. The evolution of mechanical properties and electronic structures with an increase of the oxidation degree are analyzed, revealing the transition of the ground state of uranium oxides from metallic to Mott insulator and then to charge-transfer insulator due to the interplay of strongly correlated effects of 5f orbitals and the shift of electrons from uranium to oxygen atoms.

Modeling of the dispersion of depleted uranium aerosol.

PubMed

Mitsakou, C; Eleftheriadis, K; Housiadas, C; Lazaridis, M

2003-04-01

Depleted uranium is a low-cost radioactive material that, in addition to other applications, is used by the military in kinetic energy weapons against armored vehicles. During the Gulf and Balkan conflicts concern has been raised about the potential health hazards arising from the toxic and radioactive material released. The aerosol produced during impact and combustion of depleted uranium munitions can potentially contaminate wide areas around the impact sites or can be inhaled by civilians and military personnel. Attempts to estimate the extent and magnitude of the dispersion were until now performed by complex modeling tools employing unclear assumptions and input parameters of high uncertainty. An analytical puff model accommodating diffusion with simultaneous deposition is developed, which can provide a reasonable estimation of the dispersion of the released depleted uranium aerosol. Furthermore, the period of the exposure for a given point downwind from the release can be estimated (as opposed to when using a plume model). The main result is that the depleted uranium mass is deposited very close to the release point. The deposition flux at a couple of kilometers from the release point is more than one order of magnitude lower than the one a few meters near the release point. The effects due to uncertainties in the key input variables are addressed. The most influential parameters are found to be atmospheric stability, height of release, and wind speed, whereas aerosol size distribution is less significant. The output from the analytical model developed was tested against the numerical model RPM-AERO. Results display satisfactory agreement between the two models.

Hydrologic and Temporal Influences of Evaporite Minerals on the Vertical Distribution, Storage, and Mobility of Uranium

NASA Astrophysics Data System (ADS)

Roycroft, S. J.; Noel, V.; Boye, K.; Besancon, C.; Weaver, K. L.; Johnson, R. H.; Dam, W. L.; Fendorf, S. E.; Bargar, J.

2016-12-01

Uranium contaminated groundwater in Riverton, Wyoming persists despite anticipated natural attenuation outside of a former uranium ore processing facility. The inability of natural flushing to dilute the uranium below the regulatory threshold indicates that sediments act as secondary sources likely (re)supplying uranium to groundwater. Throughout the contaminated floodplain, uranium rich-evaporites are readily abundant in the upper 2 m of sediments and are spatially coincident with the location of the plume, which suggests a likely link between evaporites and increased uranium levels. Knowledge of where and how uranium is stored within evaporite-associated sediments is required to understand processes controlling the mobility of uranium. We expect that flooding and seasonal changes in hydrologic conditions will affect U phase partitioning, and thus largely control U mobility. The primary questions we are addressing in this project are: What is the relative abundance of uranium incorporated in various mineral complexes throughout the evaporite sediments? How do the factors of depth, location, and seasonality influence the relative incorporation, mobility and speciation of uranium?We have systematically sampled from two soil columns over three dates in Riverton. The sampling dates span before and after a significant flooding event, providing insight into the flood's impact on local uranium mobility. Sequential chemical extractions are used to decipher the reactivity of uranium and approximate U operationally defined within reactants targeting carbonate, silicate, organic, and metal oxide bound or water and exchangeable phases. Extractions throughout the entirety of the sediment cores provide a high-resolution vertical profile of the distribution of uranium in various extracted phases. Throughout the profile, the majority (50-60%) of uranium is bound within carbonate-targeted extracts, a direct effect of the carbonate-rich evaporite sediments. The sum of our analyses provide a dynamic model of uranium incorporation within evaporite sediments holding implications for the fate of uranium throughout contaminated sites across the Colorado River Basin.

Bone as a Possible Target of Chemical Toxicity of Natural Uranium in Drinking Water

PubMed Central

Kurttio, Päivi; Komulainen, Hannu; Leino, Aila; Salonen, Laina; Auvinen, Anssi; Saha, Heikki

2005-01-01

Uranium accumulates in bone, affects bone metabolism in laboratory animals, and when ingested in drinking water increases urinary excretion of calcium and phosphate, important components in the bone structure. However, little is known about bone effects of ingested natural uranium in humans. We studied 146 men and 142 women 26–83 years of age who for an average of 13 years had used drinking water originating from wells drilled in bedrock, in areas with naturally high uranium content. Biochemical indicators of bone formation were serum osteocalcin and amino-terminal propeptide of type I procollagen, and a marker for bone resorption was serum type I collagen carboxy-terminal telopeptide (CTx). The primary measure of uranium exposure was uranium concentration in drinking water, with additional information on uranium intake and uranium concentration in urine. The data were analyzed separately for men and women with robust regression (which suppresses contributions of potential influential observations) models with adjustment for age, smoking, and estrogen use. The median uranium concentration in drinking water was 27 μg/L (interquartile range, 6–116 μg/L). The median of daily uranium intake was 36 μg (7–207 μg) and of cumulative intake 0.12 g (0.02–0.66 g). There was some suggestion that elevation of CTx (p = 0.05) as well as osteocalcin (p = 0.19) could be associated with increased uranium exposure (uranium in water and intakes) in men, but no similar relationship was found in women. Accordingly, bone may be a target of chemical toxicity of uranium in humans, and more detailed evaluation of bone effects of natural uranium is warranted. PMID:15626650

Dynamic Computer Model of a Stirling Space Nuclear Power System

DTIC Science & Technology

2006-05-04

diagram of electric propulsion…………………………………. 17 Figure 2-1. General NEP structure……………………………………………………….20 Figure 2-2. Fission of uranium -235...Figure 2-1. General NEP structure. [20] 21 Figure 2-2. Fission of uranium -235. In a fast reactor, the average number of neutrons...that is modeled for this project is a 600 kW(t) fast fission reactor consisting of uranium nitride fuel and sodium potassium coolant. Its dynamic

Radium and uranium concentrations and associated hydrogeochemistry in ground water in southwestern Pueblo County, Colorado

USGS Publications Warehouse

Felmlee, J. Karen; Cadigan, Robert Allen

1979-01-01

Radium and uranium concentrations in water from 37 wells tapping the aquifer system of the Dakota Sandstone and Purgatoire Formation in southwestern Pueblo County, Colorado, have a wide range of values and define several areas of high radioactivity in the ground water. Radium ranges from 0.3 to 420 picocuries per liter and has a median value of 8.8, and uranium ranges from 0.02 to 180 micrograms per liter and has a median value of 2.4. Radon concentrations, measured in 32 of the 37 wells, range from less than 100 picocuries per liter to as much as 27,000 and have a median value of 580. Relationships among the radioactive elements and 28 other geochemical parameters were studied by using correlation coefficients and R-mode factor analysis. Five factor groups were determined to represent major influences on water chemistry: (1) short-term solution reactions, (2) oxidation reactions, (3) hydrolysis reactions, (4) uranium distribution, and (5) long-term solution reactions. Uranium concentrations are most strongly influenced by oxidation reactions but also are affected by solution reactions and distribution of uranium in the rocks of the aquifer system. Radon and radium concentrations are mostly controlled by uranium distribution; radium also shows a moderate negative relationship with oxidation. To explain the statistical and spatial relationships among the parameters, a model was developed involving the selective leaching of uranium-bearing phases and metal sulfides which occur in discontinuous zones in sandstone and shale. When reducing conditions prevail, uranium is immobile, but radium can be taken into solution. When faults and associated fractured rocks allow oxidizing conditions to dominate, uranium can be taken into solution; radium can also be taken into solution, or it may become immobilized by coprecipitation with iron and manganese oxides or with barite. Several areas within the study area are discussed in terms of the model.

Evaluating the risk from depleted uranium after the Boeing 747-258F crash in Amsterdam, 1992.

PubMed

Uijt de Haag, P A; Smetsers, R C; Witlox, H W; Krüs, H W; Eisenga, A H

2000-08-28

On 4 October 1992, a large cargo plane crashed into an apartment building in the Bijlmermeer quarter of Amsterdam. In the years following the accident, an increasing number of people started reporting health complaints, which they attributed to exposure to dangerous substances after the crash. Since the aircraft had been carrying depleted uranium as counterbalance weights and about 150 kg uranium had been found missing after clearance of the crash site, exposure to uranium oxide particles was pointed out as the possible cause of their health complaints. Six years after the accident, a risk analysis was therefore carried out to investigate whether the health complaints could be attributed to exposure to uranium oxide set free during the accident. The scientific challenge was to come up with reliable results, knowing that - considering the late date - virtually no data were available to validate any calculated result. The source term of uranium was estimated using both generic and specific data. Various dispersion models were applied in combination with the local setting and the meteorological conditions at the time of the accident to estimate the exposure of bystanders during the fire caused by the crash. Emphasis was given to analysing the input parameters, inter-comparing the various models and comparing model results with the scarce information available. Uranium oxide formed in the fire has a low solubility, making the chemical toxicity to humans less important than the radiotoxicity. Best-estimate results indicated that bystanders may have been exposed to a radiation dose of less than 1 microSv, whereas a worst-case approach indicated an upper limit of less than 1 mSv. This value is considerably less than the radiation dose for which acute effects are to be expected. It is therefore considered to be improbable that the missing uranium had indeed led to the health complaints reported.

β-decay Rates for Exotic Nuclei and r-process Nucleosynthesis up to Thorium and Uranium

NASA Astrophysics Data System (ADS)

Suzuki, Toshio; Shibagaki, Shota; Yoshida, Takashi; Kajino, Toshitaka; Otsuka, Takaharu

2018-06-01

Beta-decay rates for exotic nuclei with neutron magic number of N = 126 relevant to r-process nucleosynthesis are studied up to Z = 78 by shell-model calculations. The half-lives for the waiting-point nuclei obtained, which are short compared to a standard finite-range-droplet model, are used to study r-process nucleosynthesis in core-collapse supernova (CCSN) explosions and binary neutron star mergers. The element abundances are obtained up to the third peak as well as beyond the peak region up to thorium and uranium. The position of the third peak is found to be shifted toward a higher mass region in both CCSN explosions and neutron star mergers. We find that thorium and uranium elements are produced more with the shorter shell-model half-lives and their abundances come close to the observed values in CCSN explosions. In the case of binary neutron star mergers, thorium and uranium are produced consistently with the observed values independent of the half-lives.

Illicit Trafficking of Natural Radionuclides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friedrich, Steinhaeusler; Lyudmila, Zaitseva

2008-08-07

Natural radionuclides have been subject to trafficking worldwide, involving natural uranium ore (U 238), processed uranium (yellow cake), low enriched uranium (<20% U 235) or highly enriched uranium (>20% U 235), radium (Ra 226), polonium (Po 210), and natural thorium ore (Th 232). An important prerequisite to successful illicit trafficking activities is access to a suitable logistical infrastructure enabling an undercover shipment of radioactive materials and, in case of trafficking natural uranium or thorium ore, capable of transporting large volumes of material. Covert en route diversion of an authorised uranium transport, together with covert diversion of uranium concentrate from anmore » operating or closed uranium mines or mills, are subject of case studies. Such cases, involving Israel, Iran, Pakistan and Libya, have been analyzed in terms of international actors involved and methods deployed. Using international incident data contained in the Database on Nuclear Smuggling, Theft and Orphan Radiation Sources (DSTO) and international experience gained from the fight against drug trafficking, a generic Trafficking Pathway Model (TPM) is developed for trafficking of natural radionuclides. The TPM covers the complete trafficking cycle, ranging from material diversion, covert material transport, material concealment, and all associated operational procedures. The model subdivides the trafficking cycle into five phases: (1) Material diversion by insider(s) or initiation by outsider(s); (2) Covert transport; (3) Material brokerage; (4) Material sale; (5) Material delivery. An Action Plan is recommended, addressing the strengthening of the national infrastructure for material protection and accounting, development of higher standards of good governance, and needs for improving the control system deployed by customs, border guards and security forces.« less

Illicit Trafficking of Natural Radionuclides

NASA Astrophysics Data System (ADS)

Friedrich, Steinhäusler; Lyudmila, Zaitseva

2008-08-01

Natural radionuclides have been subject to trafficking worldwide, involving natural uranium ore (U 238), processed uranium (yellow cake), low enriched uranium (<20% U 235) or highly enriched uranium (>20% U 235), radium (Ra 226), polonium (Po 210), and natural thorium ore (Th 232). An important prerequisite to successful illicit trafficking activities is access to a suitable logistical infrastructure enabling an undercover shipment of radioactive materials and, in case of trafficking natural uranium or thorium ore, capable of transporting large volumes of material. Covert en route diversion of an authorised uranium transport, together with covert diversion of uranium concentrate from an operating or closed uranium mines or mills, are subject of case studies. Such cases, involving Israel, Iran, Pakistan and Libya, have been analyzed in terms of international actors involved and methods deployed. Using international incident data contained in the Database on Nuclear Smuggling, Theft and Orphan Radiation Sources (DSTO) and international experience gained from the fight against drug trafficking, a generic Trafficking Pathway Model (TPM) is developed for trafficking of natural radionuclides. The TPM covers the complete trafficking cycle, ranging from material diversion, covert material transport, material concealment, and all associated operational procedures. The model subdivides the trafficking cycle into five phases: (1) Material diversion by insider(s) or initiation by outsider(s); (2) Covert transport; (3) Material brokerage; (4) Material sale; (5) Material delivery. An Action Plan is recommended, addressing the strengthening of the national infrastructure for material protection and accounting, development of higher standards of good governance, and needs for improving the control system deployed by customs, border guards and security forces.

Evaluation of depleted uranium in the environment at Aberdeen Proving Grounds, Maryland and Yuma Proving Grounds, Arizona. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kennedy, P.L.; Clements, W.H.; Myers, O.B.

1995-01-01

This report represents an evaluation of depleted uranium (DU) introduced into the environment at the Aberdeen Proving Grounds (APG), Maryland and Yuma Proving Grounds (YPG) Arizona. This was a cooperative project between the Environmental Sciences and Statistical Analyses Groups at LANL and with the Department of Fishery and Wildlife Biology at Colorado State University. The project represents a unique approach to assessing the environmental impact of DU in two dissimilar ecosystems. Ecological exposure models were created for each ecosystem and sensitivity/uncertainty analyses were conducted to identify exposure pathways which were most influential in the fate and transport of DU inmore » the environment. Research included field sampling, field exposure experiment, and laboratory experiments. The first section addresses DU at the APG site. Chapter topics include bioenergetics-based food web model; field exposure experiments; bioconcentration by phytoplankton and the toxicity of U to zooplankton; physical processes governing the desorption of uranium from sediment to water; transfer of uranium from sediment to benthic invertebrates; spead of adsorpion by benthic invertebrates; uptake of uranium by fish. The final section of the report addresses DU at the YPG site. Chapters include the following information: Du transport processes and pathway model; field studies of performance of exposure model; uptake and elimination rates for kangaroo rates; chemical toxicity in kangaroo rat kidneys.« less

Nuclear energy in Europe: uranium flow modeling and fuel cycle scenario trade-offs from a sustainability perspective.

PubMed

Tendall, Danielle M; Binder, Claudia R

2011-03-15

The European nuclear fuel cycle (covering the EU-27, Switzerland and Ukraine) was modeled using material flow analysis (MFA).The analysis was based on publicly available data from nuclear energy agencies and industries, national trade offices, and nongovernmental organizations. Military uranium was not considered due to lack of accessible data. Nuclear fuel cycle scenarios varying spent fuel reprocessing, depleted uranium re-enrichment, enrichment assays, and use of fast neutron reactors, were established. They were then assessed according to environmental, economic and social criteria such as resource depletion, waste production, chemical and radiation emissions, costs, and proliferation risks. The most preferable scenario in the short term is a combination of reduced tails assay and enrichment grade, allowing a 17.9% reduction of uranium demand without significantly increasing environmental, economic, or social risks. In the long term, fast reactors could theoretically achieve a 99.4% decrease in uranium demand and nuclear waste production. However, this involves important costs and proliferation risks. Increasing material efficiency is not systematically correlated with the reduction of other risks. This suggests that an overall optimization of the nuclear fuel cycle is difficult to obtain. Therefore, criteria must be weighted according to stakeholder interests in order to determine the most sustainable solution. This paper models the flows of uranium and associated materials in Europe, and provides a decision support tool for identifying the trade-offs of the alternative nuclear fuel cycles considered.

Comprehensive Evaluation of Soil Near Uranium Tailings, Beishan City, China.

PubMed

Xun, Yan; Zhang, Xinjia; Chaoliang, Chen; Luo, Xuegang; Zhang, Yu

2018-06-01

To evaluate the impact of uranium tailings on soil composition and soil microbial, six soil samples at different distance from the uranium tailings (Beishan City, China) were collected for further analysis. Concentrations of radionuclides ( 238 U and 232 Th), heavy metals (Mn, Cd, Cr, Ni, Zn, and Pb) and organochlorine pesticide were determined by ICP-MS and GC, they were significantly higher than those of the control. And the Average Well Color Development as well as the Shannon, the Evenness, and the Simpson index were calculated to evaluate the soil microbial diversity. The carbon utilization model of soil microbial community was also analyzed by Biolog-eco. All results indicated that uranium tailings leaded to excessive radionuclides and heavy metals, and decreased the diversity of the soil microbial community. Our study will provide a valuable basis for soil quality evaluation around uranium tailing repositories and lay a foundation for the management and recovery of uranium tailings.

The new nuclear west: Uranium milling as community on Colorado's western slope

NASA Astrophysics Data System (ADS)

Tidwell, Abraham S. D.

In mid-2007, Energy Fuels, a Toronto-based uranium mining and milling company, announced their intent to build Piñon Ridge, the first new conventional uranium mill in the United States in 30 years. The prospect of a return to uranium milling has mobilized community support to bring back an industry some see as both familiar and capable of supporting and growing their communities. Using transcripts generated during the Colorado Department of Public Health and Environment's public meetings and hearings during 2010 and 2012, this study examines how proponents of the mill frame the socioeconomic advantages of bringing the industry back. Applying Kinsella's bounded constitutive model of communication, this study shows that the community and the uranium mill are bound in a "sorge-enframing" duality where the care generated by each binds the other to the recalcitrant nature of the uranium industry and preconceived notions of socioeconomic development, respectively.

Distribution and timing of thick transient air-fall deposits in Electris: Implications for the nature of the upland plains

NASA Technical Reports Server (NTRS)

Grant, J. A.; Schultz, P. H.

1987-01-01

A large area in the Electris region of Mars is (or once was) covered by an unconformable and etched deposit. Although interpreted as lava filling volcano-tectonic depressions or fluvial deposits filling large degraded craters, more recent work has shown the deposit is more likely the result of air-fall deposition. Crater densities on both the surface of the deposit and on exhumed, underlying ridged plains indicate that the deposit was emplaced and eroded over a relatively short time. These crater statistics also demonstate that the relative age of the Electris deposit is similar to those obtained for other unconformable deposits, thereby suggesting they may be related.

quantifying and Predicting Reactive Transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peter C. Burns, Department of Civil Engineering and Geological Sciences, University of Notre Dame

2009-12-04

This project was led by Dr. Jiamin Wan at Lawrence Berkeley National Laboratory. Peter Burns provided expertise in uranium mineralogy and in identification of uranium minerals in test materials. Dr. Wan conducted column tests regarding uranium transport at LBNL, and samples of the resulting columns were sent to Dr. Burns for analysis. Samples were analyzed for uranium mineralogy by X-ray powder diffraction and by scanning electron microscopy, and results were provided to Dr. Wan for inclusion in the modeling effort. Full details of the project can be found in Dr. Wan's final reports for the associated effort at LBNL.

A phase-field simulation of uranium dendrite growth on the cathode in the electrorefining process

NASA Astrophysics Data System (ADS)

Shibuta, Yasushi; Unoura, Seiji; Sato, Takumi; Shibata, Hiroki; Kurata, Masaki; Suzuki, Toshio

2011-07-01

The uranium dendrite growth on the cathode during the pyroprocessing of uranium is investigated using a novel phase-field model, in which electrodeposition of uranium and zirconium from the molten-salt is taken into account. The threshold concentration of zirconium in the molten salt demarcating the dendritic and planar growth is then estimated as a function of the current density. Moreover, the growth process of both the dendritic and planar electrodeposits has been demonstrated by way of varying the mobility of the phase field, which consists of the effect of attachment kinetics and diffusion.

Influence of Large Igneous Provinces on Svalbard tectonics and sedimentation from the Late Mesozoic through Cenozoic: Insight from (U-Th)/He zircon and apatite thermochronology

NASA Astrophysics Data System (ADS)

Barnes, Christopher; Schneider, David; Majka, Jaroslaw

2016-04-01

Svalbard, the northwestern sub-aerial exposure of the Barents Shelf, offers significant insight into the geodynamics of the High Arctic. The tectonics and sedimentation on Svalbard from the Late Mesozoic through Cenozoic can be attributed to two Large Igneous Provinces: the High Arctic Large Igneous Province (HALIP; 130-90 Ma) and the North Atlantic Large Igneous Province (NAIP; 62-55 Ma). The relationship between the HALIP and the tectonics of the High Arctic remains somewhat unclear, whereas the NAIP is directly linked to opening of the North Atlantic Ocean. This study attempts to establish links between the HALIP and geodynamics of the High Arctic, and reveals the far-field tectonic consequences of the NAIP on Svalbard and the High Arctic. We focus on the Southwestern Caledonian Basement Terrane of Svalbard, characterized by the West Spitsbergen Fold and Thrust Belt, formed during the Eurekan Orogeny (c. 55-33 Ma). Crystalline basement was sampled from four regions (Prins Karls Forland, Oscar II Land, Wedel Jarlsberg Land, and Sørkapp Land) for the purpose of zircon and apatite (U-Th)/He thermochronometry which allows for resolution of thermal events below 200°C. We forward model our datasets using HeFTy software to produce temperature-time histories for each of these regions, and compare these thermal models with Svalbard stratigraphy to resolve the geodynamics of Svalbard from the Late Mesozoic through Cenozoic. The Cretaceous stratigraphy of Svalbard is characterized by a short-lived Mid-Cretaceous sub-aerial unconformity (c. 129 Ma) and a significant Late Cretaceous unconformity (c. 105-65 Ma). Our thermal models reveal a Mid-Cretaceous heating event, suggesting an increasing geothermal gradient coeval with development of the first unconformity. This may indicate that short-lived domal-uplift, related to the arrival of the HALIP plume, was a primary control on Svalbard tectonics and sedimentary deposition throughout the Mid-Cretaceous. Late Cretaceous cooling (85-65 Ma), coeval with development of the Late Cretaceous unconformity, is indicative of moderate uplift on Svalbard during this time. We interpret this as rift-flank uplift, related to opening in the Lincoln Sea north of Svalbard. Given the location of the HALIP plume on the southern Alpha Ridge, we suggest that HALIP emplacement contributed to a stress-field facilitating rifting in the Lincoln Sea (a precursor to rifting of the southern Eurasian Basin; c. 56 Ma). A change in paleoflow direction of Svalbard sediments from Paleogene NNE-sourced to Eocene W-sourced sediments denotes a change from HALIP-influenced to NAIP-influenced tectonics and sedimentation on Svalbard. An Eocene heating event (55-40 Ma) is the result of tectonic burial via overthrusting during the Eurekan Orogeny, providing the western sediment source. Eurekan tectonism on Svalbard is the result of the northward movement of the Greenland microplate, a consequence of spreading in the North Atlantic Ocean. The most recent cooling event (40-20 Ma) is primarily attributed to rift-flank uplift resulting from northward propagation of the North Atlantic Ocean and opening of the Fram Strait. Low-temperature (U-Th)/He low-temperature thermochronometry allow us to document shallow crustal processes that, which are linked to Large Igneous Provinces and other mantle dynamics.

Uranium speciation and stability after reductive immobilization in aquifer sediments

NASA Astrophysics Data System (ADS)

Sharp, Jonathan O.; Lezama-Pacheco, Juan S.; Schofield, Eleanor J.; Junier, Pilar; Ulrich, Kai-Uwe; Chinni, Satya; Veeramani, Harish; Margot-Roquier, Camille; Webb, Samuel M.; Tebo, Bradley M.; Giammar, Daniel E.; Bargar, John R.; Bernier-Latmani, Rizlan

2011-11-01

It has generally been assumed that the bioreduction of hexavalent uranium in groundwater systems will result in the precipitation of immobile uraninite (UO 2). In order to explore the form and stability of uranium immobilized under these conditions, we introduced lactate (15 mM for 3 months) into flow-through columns containing sediments derived from a former uranium-processing site at Old Rifle, CO. This resulted in metal-reducing conditions as evidenced by concurrent uranium uptake and iron release. Despite initial augmentation with Shewanella oneidensis, bacteria belonging to the phylum Firmicutes dominated the biostimulated columns. The immobilization of uranium (˜1 mmol U per kg sediment) enabled analysis by X-ray absorption spectroscopy (XAS). Tetravalent uranium associated with these sediments did not have spectroscopic signatures representative of U-U shells or crystalline UO 2. Analysis by microfocused XAS revealed concentrated micrometer regions of solid U(IV) that had spectroscopic signatures consistent with bulk analyses and a poor proximal correlation (μm scale resolution) between U and Fe. A plausible explanation, supported by biogeochemical conditions and spectral interpretations, is uranium association with phosphoryl moieties found in biomass; hence implicating direct enzymatic uranium reduction. After the immobilization phase, two months of in situ exposure to oxic influent did not result in substantial uranium remobilization. Ex situ flow-through experiments demonstrated more rapid uranium mobilization than observed in column oxidation studies and indicated that sediment-associated U(IV) is more mobile than biogenic UO 2. This work suggests that in situ uranium bioimmobilization studies and subsurface modeling parameters should be expanded to account for non-uraninite U(IV) species associated with biomass.

Uranium uptake history, open-system behaviour and uranium-series ages of fossil Tridacna gigas from Huon Peninsula, Papua New Guinea

NASA Astrophysics Data System (ADS)

Ayling, Bridget F.; Eggins, Stephen; McCulloch, Malcolm T.; Chappell, John; Grün, Rainer; Mortimer, Graham

2017-09-01

Molluscs incorporate negligible uranium into their skeleton while they are living, with any uranium uptake occurring post-mortem. As such, closed-system U-series dating of molluscs is unlikely to provide reliable age constraints for marine deposits. Even the application of open-system U-series modelling is challenging, because uranium uptake and loss histories can affect time-integrated uranium distributions and are difficult to constrain. We investigate the chemical and isotopic distribution of uranium in fossil Tridacna gigas (giant clams) from Marine Isotope Stage (MIS) 5e (128-116 ka) and MIS 11 (424-374 ka) reefs at Huon Peninsula in Papua New Guinea. The large size of the clams enables detailed chemical and isotopic mapping of uranium using LA-ICPMS and LA-MC-ICPMS techniques. Within each fossil Tridacna specimen, marked differences in uranium concentrations are observed across the three Tridacna growth zones (outer, inner, hinge), with the outer and hinge zones being relatively enriched. In MIS 5e and MIS 11 Tridacna, the outer and hinge zones contain approximately 1 ppm and 5 ppm uranium respectively. In addition to uptake of uranium, loss of uranium appears prevalent, especially in the MIS 11 specimens. The effect of uranium loss is to elevate measured [230Th/238U] values with little effect on [234U/238U] values. Closed-system age estimates are on average 50% too young for the MIS 5e Tridacna, and 25% too young for the MIS 11 Tridacna. A complex, multi-stage uptake and loss history is interpreted for the fossil Tridacna and we demonstrate that they cannot provide independent, reliable geochronological controls on the timing of past reef growth at Huon Peninsula.

Numerical simulation of migration behavior of uranium ore dust particles in the human respiratory tract

NASA Astrophysics Data System (ADS)

Ye, Yong-jun; Yin, An-song; Li, Zhi; Lei, Bo; Ding, De-xin

2017-04-01

There is a certain concentration of radioactive dust particles in the air of workplace of underground uranium mines. Some small diameter particles will pass through the masks and enter the respiratory tract which will cause radiation damage to the human body. In order to study deposition regularity of uranium dust in the human respiratory tract, in this paper, we firstly use the RNG turbulence model to simulate the gas flow field in the human respiratory tract Z0 ∼ Z3 level under different respiratory intensity. Then we use DPM discrete phase model to simulate the concentration, particle size distribution, deposition rate and deposition share of uranium dust particles after being filtered through the masks in the human respiratory tract Z0 to Z3 bronchus. According to the simulation results, we have got the following conclusions: the particles’ number concentration of uranium dust after being filtered through the mask in the human respiratory tract basically decreases with the increasing of particle size under different respiratory intensities on the environment of uranium mine. In addition, the intensity of respiration and the mass concentration of particles have an important influence on the deposition rate and the deposition of particles in the respiratory tract.

Rapid and efficient uranium(VI) capture by phytic acid/polyaniline/FeOOH composites.

PubMed

Wei, Xintao; Liu, Qi; Zhang, Hongsen; Liu, Jingyuan; Chen, Rongrong; Li, Rumin; Li, Zhangshuang; Liu, Peili; Wang, Jun

2018-02-01

Uranium plays an indispensable role in nuclear energy, but there are limited land resources to meet the ever growing demand; therefore, a need exists to develop efficient materials for capturing uranium from water. Herein, we synthesize a promising adsorbent of phytic acid/polyaniline/FeOOH composites (PA/PANI/FeOOH) by oxidative polymerization. Phytic acid, acting asa gelator and dopant, plays an important role in the formation of polyaniline (PANI). The PA/PANI/FeOOH exhibites high adsorption capacity (q m =555.8mgg -1 , T=298K), rapid adsorption rate (within 5min), excellent selectivity and cyclic stability. In addition, the results show that the adsorption isotherm is well fitted to the Langmuir isotherm model, and the adsorption kinetics agree with a pseudo-second order model. XPS analysis indicates that the removal of uranium is mainly attributed to abundant amine and imine groups on the surface of PA/PANI/FeOOH. Importantly, the removal of uranium from low concentrations of simulated seawater is highly efficient with a removal rate exceeding 92%. From our study, superior adsorption capacities, along with a low-cost, environmentally friendly and facile synthesis, reveal PA/PANI/FeOOH asa promising material for uranium capture. Copyright © 2017. Published by Elsevier Inc.

Corridors of crestal and radial faults linking salt diapirs in the Espírito Santo Basin, SE Brazil

NASA Astrophysics Data System (ADS)

Mattos, Nathalia H.; Alves, Tiago M.

2018-03-01

This work uses high-quality 3D seismic data to assess the geometry of fault families around salt diapirs in SE Brazil (Espírito Santo Basin). It aims at evaluating the timings of fault growth, and suggests the generation of corridors for fluid migration linking discrete salt diapirs. Three salt diapirs, one salt ridge, and five fault families were identified based on their geometry and relative locations. Displacement-length (D-x) plots, Throw-depth (T-z) data and structural maps indicate that faults consist of multiple segments that were reactivated by dip-linkage following a preferential NE-SW direction. This style of reactivation and linkage is distinct from other sectors of the Espírito Santo Basin where the preferential mode of reactivation is by upwards vertical propagation. Reactivation of faults above a Mid-Eocene unconformity is also scarce in the study area. Conversely, two halokinetic episodes dated as Cretaceous and Paleogene are interpreted below a Mid-Eocene unconformity. This work is important as it recognises the juxtaposition of permeable strata across faults as marking the generation of fault corridors linking adjacent salt structures. In such a setting, fault modelling shows that fluid will migrate towards the shallower salt structures along the fault corridors first identified in this work.

Estimates of radiological risk from depleted uranium weapons in war scenarios.

PubMed

Durante, Marco; Pugliese, Mariagabriella

2002-01-01

Several weapons used during the recent conflict in Yugoslavia contain depleted uranium, including missiles and armor-piercing incendiary rounds. Health concern is related to the use of these weapons, because of the heavy-metal toxicity and radioactivity of uranium. Although chemical toxicity is considered the more important source of health risk related to uranium, radiation exposure has been allegedly related to cancers among veterans of the Balkan conflict, and uranium munitions are a possible source of contamination in the environment. Actual measurements of radioactive contamination are needed to assess the risk. In this paper, a computer simulation is proposed to estimate radiological risk related to different exposure scenarios. Dose caused by inhalation of radioactive aerosols and ground contamination induced by Tomahawk missile impact are simulated using a Gaussian plume model (HOTSPOT code). Environmental contamination and committed dose to the population resident in contaminated areas are predicted by a food-web model (RESRAD code). Small values of committed effective dose equivalent appear to be associated with missile impacts (50-y CEDE < 5 mSv), or population exposure by water-independent pathways (50-y CEDE < 80 mSv). The greatest hazard is related to the water contamination in conditions of effective leaching of uranium in the groundwater (50-y CEDE < 400 mSv). Even in this worst case scenario, the chemical toxicity largely predominates over radiological risk. These computer simulations suggest that little radiological risk is associated to the use of depleted uranium weapons.

U-Pb (zircon) and geochemical constraints on the age, origin, and evolution of Paleozoic arc magmas in the Oyu Tolgoi porphyry Cu-Au district, southern Mongolia

USGS Publications Warehouse

Wainwright, A.J.; Tosdal, R.M.; Wooden, J.L.; Mazdab, F.K.; Friedman, R.M.

2011-01-01

Uranium-Pb (zircon) ages are linked with geochemical data for porphyry intrusions associated with giant porphyry Cu-Au systems at Oyu Tolgoi to place those rocks within the petrochemical framework of Devonian and Carboniferous rocks of southern Mongolia. In this part of the Gurvansayhan terrane within the Central Asian Orogenic Belt, the transition from Devonian tholeiitic marine rocks to unconformably overlying Carboniferous calc-alkaline subaerial to shallow marine volcanic rocks reflects volcanic arc thickening and maturation. Radiogenic Nd and Pb isotopic compositions (??Nd(t) range from +3.1 to +7.5 and 206Pb/204Pb values for feldspars range from 17.97 to 18.72), as well as low high-field strength element (HFSE) contents of most rocks (mafic rocks typically have <1.5% TiO2) are consistent with magma derivation from depleted mantle in an intra-oceanic volcanic arc. The Late Devonian and Carboniferous felsic rocks are dominantly medium- to high-K calc-alkaline and characterized by a decrease in Sr/Y ratios through time, with the Carboniferous rocks being more felsic than those of Devonian age. Porphyry Cu-Au related intrusions were emplaced in the Late Devonian during the transition from tholeiitic to calc-alkaline arc magmatism. Uranium-Pb (zircon) geochronology indicates that the Late Devonian pre- to syn-mineral quartz monzodiorite intrusions associated with the porphyry Cu-Au deposits are ~372Ma, whereas granodiorite intrusions that post-date major shortening and are associated with less well-developed porphyry Cu-Au mineralization are ~366Ma. Trace element geochemistry of zircons in the Late Devonian intrusions associated with the porphyry Cu-Au systems contain distinct Th/U and Yb/Gd ratios, as well as Hf and Y concentrations that reflect mixing of magma of distinct compositions. These characteristics are missing in the unmineralized Carboniferous intrusions. High Sr/Y and evidence for magma mixing in syn- to late-mineral intrusions distinguish the Late Devonian rocks associated with giant Cu-Au deposits from younger magmatic suites in the district. ?? 2010 Elsevier B.V.

Dynamic Passage of Topography Beneath the Southern Costa Rica Forearc seen with Seismic Stratigraphy

NASA Astrophysics Data System (ADS)

Edwards, J. H.; Kluesner, J. W.; Silver, E. A.

2014-12-01

3D seismic reflection data (CRISP) collected across the southern Costa Rica margin reveals that a thick, deforming sedimentary wedge underlies the younger slope sediments (Silver et al., this meeting). The older wedge material and younger slope sediments are separated by a high-amplitude regional unconformity. Seismic stratigraphy of the sedimentary strata overlying this regional unconformity reflects a dynamic deformation history of the margin. The younger slope sediments contain series of more localized unconformities, separating sedimentary units as thick as 1 km that reveal a dynamically changing set of inverted, overlapping basins. The geometry of these overlapping, inverted basins indicate sequential uplift events. The direction of basin thickening varies upsection, and these basins are cut by both thrust and normal faults and are deformed by folding. Structural development appears to be controlled by relief on the subducting plate interface, which induces uplift and subsidence and thereby controls the pattern of erosion and deposition. We interpret the evolution of these inverted stratigraphic packages as forming from subducting topography. Correlating these seismic-stratigraphic packages to recent drilling based on preliminary magnetostratigraphy from IODP site U1413 (Expedition 344 Scientists, 2013), allows us to date the passage of the subducting plate topography beginning ~2 Ma.

Devonian-Carboniferous unconformity in Argentina and its relation to the Eo-Hercynian orogeny in southern South America

NASA Astrophysics Data System (ADS)

López-Gamundí, O. R.; Rossello, E. A.

1993-04-01

The Devonian-Carboniferous contact in southern South America, characterized by a sharp unconformity, has been related to the Late Devonian-Early Carboniferous Eo-Hercynian orogeny. The Calingasta-Uspallata basin of western Argentina and the Sauce-Grande basin (Ventana Foldbelt) of eastern Argentina have been selected to characterize this unconformity. The Eo-Hercynian movements were accompanied in western Argentina by igneous activity related to a Late Devonian—Early Carboniferous magmatic arc mainly exposed today along the Andean Cordillera. This magmatic activity is partly reflected also in eastern Argentina (Ventana Foldbelt), where isotopic dates suggest a thermal event also related to the intrusions present to the west in the North Patagonian Massif and Sierras Pampeanas. The scarcity of Lower Carboniferous deposits in the stratigraphic record of southern South America suggests that the Early Carboniferous was a time interval dominated by uplift and erosion followed by widespread subsidence during the Middle and Late Carboniferous. The origin of the Eo-Hercynian orogeny can be linked with the convergence between the Arequipa Massif, and its southern extension, and the South American continent. Its effects are best represented along the ‘Palaeo-Pacific’ margin, although distant effects are discernible in the cratonic areas of eastern South America.

Raoultella sp. SM1, a novel iron-reducing and uranium-precipitating strain.

PubMed

Sklodowska, Aleksandra; Mielnicki, Sebastian; Drewniak, Lukasz

2018-03-01

The main aim of this study was the characterisation of novel Raoutella isolate, an iron-reducing and uranium-precipitating strain, originating from microbial mats occurring in the sediments of a closed down uranium mine in Kowary (SW Poland). Characterisation was done in the context of its potential role in the functioning of these mats and the possibility to use them in uranium removal/recovery processes. In our experiment, we observed the biological precipitation of iron and uranium's secondary minerals containing oxygen, potassium, sodium and phosphor, which were identified as ningyoite-like minerals. The isolated strain, Raoultella sp. SM1, was also able to dissimilatory reduce iron (III) and uranium (VI) in the presence of citrate as an electron donor. Our studies allowed us to characterise a new strain which may be used as a model microorganism in the study of Fe and U respiratory processes and which may be useful in the bioremediation of uranium-contaminated waters and sediments. During this process, uranium may be immobilised in ningyoite-like minerals and can then be recovered in nano/micro-particle form, which may be easily transformed to uraninite. Copyright © 2017 Elsevier Ltd. All rights reserved.

Uptake of uranium from seawater by amidoxime-based polymeric adsorbent marine testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsouris, C.; Kim, J.; Oyola, Y.

2013-07-01

Amidoxime-based polymer adsorbents in the form of functionalized fibers were prepared at the Oak Ridge National Laboratory (ORNL) and screened in laboratory experiments, in terms of uranium uptake capacity, using spiked uranium solution and seawater samples. Batch laboratory experiments conducted with 5-gallon seawater tanks provided equilibrium information. Based on results from 5-gallon experiments, the best adsorbent was selected for field-testing of uranium adsorption from seawater. Flow-through column tests have been performed at different marine sites to investigate the uranium uptake rate and equilibrium capacity under diverse biogeochemistry. The maximum amount of uranium uptake from seawater tests at Sequim, WA, wasmore » 3.3 mg U/g adsorbent after eight weeks of contact of the adsorbent with seawater. This amount was three times higher than the maximum adsorption capacity achieved in this study by a leading adsorbent developed by the Japan Atomic Energy Agency (JAEA), which was 1.1 mg U/g adsorbent at equilibrium. The initial uranium uptake rate of the ORNL adsorbent was 2.6 times higher than that of the JAEA adsorbent under similar conditions. A mathematical model derived from the mass balance of uranium was employed to describe the data. (authors)« less

Organic matter diagenesis as the key to a unifying theory for the genesis of tabular uranium-vanadium deposits in the Morrison Formation, Colorado Plateau

USGS Publications Warehouse

Hansley, P.L.; Spirakis, C.S.

1992-01-01

Interstitial, epigenetic amorphous organic matter is intimately associated with uranium in the Grants uranium region and is considered essential to genetic models for these deposits. In contrast, uranium minerals are intimately associated with authigenic vanadium chlorite and vanadium oxides in amorphous organic matter-poor ores of the Slick Rock and Henry Mountains mining districts and therefore, in some genetic models amorphous organic matter is not considered crucial to the formation of these deposits. Differences in organic matter content can be explained by recognizing that amorphous organic matter-poor deposits have been subjected to more advanced stages of diagenesis than amorphous organic matter-rich deposits. Evidence that amorphous organic matter was involved in the genesis of organic matter-poor, as well as organic matter-rich, deposits is described. -from Authors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eppich, Gary R.; Williams, Ross W.; Gaffney, Amy M.

Here, age dating of nuclear material can provide insight into source and suspected use in nuclear forensic investigations. We report here a method for the determination of the date of most recent chemical purification for uranium materials using the 235U- 231Pa chronometer. Protactinium is separated from uranium and neptunium matrices using anion exchange resin, followed by sorption of Pa to an SiO 2 medium. The concentration of 231Pa is measured by isotope dilution mass spectrometry using 233Pa spikes prepared from an aliquot of 237Np and calibrated in-house using the rock standard Table Mountain Latite and the uranium isotopic standard U100.more » Combined uncertainties of age dates using this method are 1.5 to 3.5 %, an improvement over alpha spectrometry measurement methods. Model ages of five uranium standard reference materials are presented; all standards have concordant 235U- 231Pa and 234U- 230Th model ages.« less

Theoretical analysis of uranium-doped thorium dioxide: Introduction of a thoria force field with explicit polarization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shields, A. E.; Ruiz Hernandez, S. E.; Leeuw, N. H. de, E-mail: DeLeeuwN@Cardiff.ac.uk

2015-08-15

Thorium dioxide is used industrially in high temperature applications, but more insight is needed into the behavior of the material as part of a mixed-oxide (MOX) nuclear fuel, incorporating uranium. We have developed a new interatomic potential model including polarizability via a shell model, and commensurate with a prominent existing UO{sub 2} potential, to conduct configurational analyses and to investigate the thermophysical properties of uranium-doped ThO{sub 2}. Using the GULP and Site Occupancy Disorder (SOD) computational codes, we have analyzed the distribution of low concentrations of uranium in the bulk material, where we have not observed the formation of uraniummore » clusters or the dominance of a single preferred configuration. We have calculated thermophysical properties of pure thorium dioxide and Th{sub (1−x)}U{sub x}O{sub 2} which generated values in very good agreement with experimental data.« less

Paleobathymetric Reconstruction of Ross Sea: seismic data processing and regional reflectors mapping

NASA Astrophysics Data System (ADS)

Olivo, Elisabetta; De Santis, Laura; Wardell, Nigel; Geletti, Riccardo; Busetti, Martina; Sauli, Chiara; Bergamasco, Andrea; Colleoni, Florence; Vanzella, Walter; Sorlien, Christopher; Wilson, Doug; De Conto, Robert; Powell, Ross; Bart, Phil; Luyendyk, Bruce

2017-04-01

PURPOSE: New maps of some major unconformities of the Ross Sea have been reconstructed, by using seismic data grids, combined with the acoustic velocities from previous works, from new and reprocessed seismic profiles. This work is carried out with the support of PNRA and in the frame of the bilateral Italy-USA project GLAISS (Global Sea Level Rise & Antarctic Ice Sheet Stability predictions), funded by the Ministry of Foreign Affairs. Paleobathymetric maps of 30, 14 and 4 million years ago, three 'key moments' for the glacial history of the Antarctic Ice Sheet, coinciding with global climatic changes. The paleobathymetric maps will then be used for numeric simulations focused on the width and thickness of the Ross Sea Ice Sheet. PRELIMINARY RESULTS: The first step was to create TWT maps of three main unconformity (RSU6, RSU4, and RSU2) of Ross Sea, revisiting and updating the ANTOSTRAT maps, through the interpretation of sedimentary bodies and erosional features, used to infer active or old processes along the slope, we identified the main seismic unconformities. We used the HIS Kingdom academic license. The different groups contribution was on the analysis of the Eastern Ross Sea continental slope and rise (OGS), of the Central Basin (KOPRI) of the western and central Ross Sea (Univ. of Santa Barbara and OGS), where new drill sites and seismic profiles were collected after the publication of the ANTOSTRAT maps. Than we joined our interpretation with previous interpretations. We examined previous processing of several seismic lines and all the old acoustic velocity analysis. In addiction we reprocessed some lines in order to have a higher data coverage. Then, combining the TWT maps of the unconformity with the old and new speed data we created new depth maps of the study area. The new depth maps will then be used for reconstructing the paleobathymetry of the Ross Sea by applying backstripping technique.

Paleontology and physical stratigraphy of the USGS-Pregnall No. 1 core (DOR-208), Dorchester County, South Carolina

USGS Publications Warehouse

Edwards, L.E.; Bybell, L.M.; Gohn, G.S.; Frederiksen, N.O.

1997-01-01

Pregnall No. 1, a 346-ft-deep corehole in northern Dorchester County, South Carolina, recovered sediments of late Paleocene, middle and late Eocene, and late Oligocene age. The core bottomed in the Chicora Member of the Williamsburg Formation (Black Mingo Group) of late Paleocene age (calcareous nannofossil Zones NP 7/8 (?) and NP 9). The Chicora (346 to 258 ft depth) consists of two contrasting lithologic units, a lower siliciclastic section of terrigenous sand, silt, and clay, and an upper carbonate section of moldic pelecypod limestone. The Chicora is overlain unconformably by the middle Eocene Moultrie Member of the Santee Limestone (Orangeburg Group). The Moultrie (258.0 to 189.4 ft) consists primarily of bryozoan-pelecypod-peloid packstones and grainstones, which are assigned to calcareous nannofossil Zone NP 16. Unconformably above the Moultrie are the locally shelly, microfossiliferous limestones of the Cross Member of the Santee Limestone (Orangeburg Group), which are assigned to middle Eocene Zone NP 17 and upper Eocene Zone NP 18. The Cross Member (189.4 to 90.9 ft) is unconformably overlain by a very thin, basal section of the upper Eocene Harleyville Formation (Cooper Group). The thin Harleyville section consists of fossiliferous limestone, primarily pelecypod-foraminifer-peloid packstones (90.9 to 85.8 ft), and is assigned to Zone NP 18, although samples from thicker Harleyville sections in the region typically are assigned to upper Eocene Zone NP 19/20. The Harleyville is overlain unconformably by the upper Oligocene Ashley Formation (Cooper Group). The Ashley Formation (85.8 to 30.0 ft) consists of a relatively homogeneous section of calcareous, microfossiliferous, silty and sandy clays assigned to Zones NP 24 and NP 25 (?). Neogene and (or) Quaternary deposits present in the upper 30 ft of the Pregnall section are assigned provisionally to an unnamed unit (30 to 22 ft) and to the Waccamaw Formation(?)(22 to 0 ft).

The sequence stratigraphy of the latest Cretaceous sediments of northern Wyoming: The interplay of tectonic and eustatic controls on foreland basin sedimentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hicks, J.F.; Tauxe, L.

1992-01-01

A west-east chronostratigraphic correlation has been made of the latest Cretaceous sediments of northern Wyoming. Five sections from Jackson Hole to Red Bird have been dated magnetostratigraphically (C34N-C26R) and radiometrically (81-68 Ma), and integrated with the ammonite biostratigraphy of the Niobrara and Pierre Shale. Four major sequence surfaces have been identified in section and the time missing within the unconformities has been measured and traced laterally. These bounding unconformities define six alloformations. The lowest straddles the C34N/C33R chronic boundary and contains the Cody, Telegraph Creek and Eagle Fms. The second ranges from the mid- to upper part of C33N ofmore » C32R and contains the Claggett and Judith River/Mesaverde Fms. The third (C32R ) is the Teapot Sandstone Member of the Mesaverde Fm. The fourth extends from the lower to upper part of C32N or to mid-C31R and includes the Bearpaw Shale and Meeteetse Fm. The fifth extends from C31N to C30N or C29N and includes the Harebell and Lance Fms. The base of the uppermost alloformation has been identified within C26R in the uppermost alloformation has been identified within C26R in the lowermost Fort Union. The unconformable surfaces are angular adjacent to the Sevier Thrust Belt but form paraconformities or hiatuses in the marine units to the east. The unconformities are eustatically controlled throughout the Campanian, but become tectonically driven in the Maastrichtian with the onset of rapid foredeep subsidence in Jackson Hole, and forebulge uplift in the Bighorn and Wind River Basin region which correlates exactly to the rapid regression of the Bearpaw Sea from the area in the range of Baculites clinolobatus.« less

A new model for tabular-type uranium deposits

USGS Publications Warehouse

Sanford, R.F.

1992-01-01

Tabular-type uranium deposits occur as tabular, originally subhorizontal bodies entirely within reduced fluvial sandstones of Late Silurian age or younger. This paper proposes that belts of tabular-type uranium deposits formed in areas of mixed local and regional groundwater discharge shortly after deposition of the host sediments. The general characteristics of tabular-type uranium deposits indicate that their essential feature was the formation at a density-stratified ground-water interface in areas of local and regional ground-water discharge. Reconstruction of the paleohydrogeology is the key to understanding the formation of these deposits. Geologic ground-water controls that favor discharge, such as the pinch-out of major aquifers, are also favorable for uranium ore. The combination of topographic and geologic features that both cause discharge is most favorable for ore deposition. -from Author

Neogene stratigraphy, foraminifera, diatoms, and depositional history of Maria Madre Island, Mexico: Evidence of early Neogene marine conditions in the southern Gulf of California

USGS Publications Warehouse

McCloy, C.; Ingle, J.C.; Barron, J.A.

1988-01-01

Foraminifera and diatoms have been analyzed from an upper Miocene through Pleistocene(?) sequence of marine sediments exposed on Maria Madre Island, largest of the Tre??s Marias Islands off the Pacific coast of Mexico. The Neogene stratigraphic sequence exposed on Maria Madre Island includes a mid-Miocene(?) non-marine and/or shallow marine sandstone unconformably overlain by a lower upper Miocene to uppermost Miocene upper to middle bathyal laminated and massive diatomite, mudstone, and siltstone unit. This unit is unconformably overlain by lower Pliocene middle to lower bathyal sandstones and siltstones which, in turn, are unconformably overlain by upper Pliocene through Pleistocene(?) upper bathyal to upper middle bathyal foraminiferal limestones and siltstones. These beds are unconformably capped by Pleistocene terrace deposits. Basement rocks on the island include Cretaceous granite and granodiorite, and Tertiary(?) andesites and rhyolites. The upper Miocene diatomaceous unit contains a low diversity foraminiferal fauna dominated by species of Bolivina indicating low oxygen conditions in the proto-Gulf Maria Madre basin. The diatomaceous unit grades into a mudstone that contains a latest Miocene upper to middle bathyal biofacies characterized by Baggina californica and Uvigerina hootsi along with displaced neritic taxa. An angular unconformity separates the upper Miocene middle bathyal sediments from overlying lower Pliocene siltstones and mudstones that contain a middle to lower bathyal biofacies and abundant planktonic species including Neogloboquadrina acostaensis and Pulleniatina primalis indicating an early Pliocene age. Significantly, this Pliocene unit contains common occurrences of benthic species restricted to Miocene sediments in California including Bulimina uvigerinaformis. Pliocene to Pleistocene(?) foraminiferal limestones and siltstones characterize submarine bank accumulations formed during uplift of the Tre??s Marias Island area, and include abundant planktonic foraminifera such as Pulleniatina obliquiloculata and Neogloboquadrina duterteri. Common benthic foraminifera in this unit are indicative of upper bathyal water depths. The Neogene depositional history recorded on Maria Madre Island involves an early late Miocene subsidence event marking formation of the Tre??s Marias Basin with relatively undiluted diatomaceous sediment deposited in a low oxygen setting. Subsidence and deepening of the basin continued into the early Pliocene along with rapid deposition of terrigenous clastics. Uplift of the basinal sequence began in late Pliocene time accompanied by deposition of upper Pliocene-Pleistocene foraminiferal limestones on a rising submarine bank. Continued episodic uplift of the Neogene deposits brought the island above sea level by late Pleistocene time. ?? 1988.

The Influence of Oxygen and Sulfur on Uranium Partitioning Into the Core

NASA Astrophysics Data System (ADS)

Moore, R. D., Jr.; Van Orman, J. A.; Hauck, S. A., II

2017-12-01

Uranium, along with K and Th, may provide substantial long-term heating in planetary cores, depending on the magnitude of their partitioning into the metal during differentiation. In general, non-metallic light elements are known to have a large influence on the partitioning of trace elements, and the presence of sulfur is known to enhance the partitioning of uranium into the metal. Data from the steelmaking literature indicate that oxygen also enhances the solubility of oxygen in liquid iron alloys. Here we present experimental data on the partitioning of U between immiscible liquids in the Fe-S-O system, and use these data along with published metal-silicate partitioning data to calibrate a quantitative activity model for U in the metal. We also determined partition coefficients for Th, K, Nb, Nd, Sm, and Yb, but were unable to fully constrain activity models for these elements with available data. A Monte Carlo fitting routine was used to calculate U-S, U-O, and U-S-O interaction coefficients, and their associated uncertainties. We find that the combined interaction of uranium with sulfur and oxygen is predominant, with S and O together enhancing the solubility of uranium to a far greater degree than either element in isolation. This suggests that uranium complexes with sulfite or sulfate species in the metal. For a model Mars core composition containing 14 at% S and 5 at% O, the metal/silicate partition coefficient for U is predicted to be an order of magnitude larger than for a pure Fe-Ni core.

System-Scale Model of Aquifer, Vadose Zone, and River Interactions for the Hanford 300 Area - Application to Uranium Reactive Transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rockhold, Mark L.; Bacon, Diana H.; Freedman, Vicky L.

2013-10-01

This report represents a synthesis and integration of basic and applied research into a system-scale model of the Hanford 300 Area groundwater uranium plume, supported by the U.S. Department of Energy’s Richland Operations (DOE-RL) office. The report integrates research findings and data from DOE Office of Science (DOE-SC), Office of Environmental Management (DOE-EM), and DOE-RL projects, and from the site remediation and closure contractor, Washington Closure Hanford, LLC (WCH). The three-dimensional, system-scale model addresses water flow and reactive transport of uranium for the coupled vadose zone, unconfined aquifer, and Columbia River shoreline of the Hanford 300 Area. The system-scale modelmore » of the 300 Area was developed to be a decision-support tool to evaluate processes of the total system affecting the groundwater uranium plume. The model can also be used to address “what if” questions regarding different remediation endpoints, and to assist in design and evaluation of field remediation efforts. For example, the proposed cleanup plan for the Hanford 300 Area includes removal, treatment, and disposal of contaminated sediments from known waste sites, enhanced attenuation of uranium hot spots in the vadose and periodically rewetted zone, and continued monitoring of groundwater with institutional controls. Illustrative simulations of polyphosphate infiltration were performed to demonstrate the ability of the system-scale model to address these types of questions. The use of this model in conjunction with continued field monitoring is expected to provide a rigorous basis for developing operational strategies for field remediation and for defining defensible remediation endpoints.« less

Modeling of point defects and rare gas incorporation in uranium mono-carbide

NASA Astrophysics Data System (ADS)

Chartier, A.; Van Brutzel, L.

2007-02-01

An embedded atom method (EAM) potential has been established for uranium mono-carbide. This EAM potential was fitted on structural properties of metallic uranium and uranium mono-carbide. The formation energies of point defects, as well as activation energies for self migration, have been evaluated in order to cross-check the suitability of the potential. Assuming that the carbon vacancies are the main defects in uranium mono-carbide compounds, the migration paths and energies are consistent with experimental data selected by Catlow[C.R.A. Catlow, J. Nucl. Mater. 60 (1976) 151]. The insertion and migration energies for He, Kr and Xe have also been evaluated with available inter-atomic potentials [H.H. Andersen, P. Sigmund, Nucl. Instr. and Meth. B 38 (1965) 238]. Results show that the most stable defect configuration for rare gases is within uranium vacancies. The migration energy of an interstitial Xe is 0.5 eV, in agreement with the experimental value of 0.5 eV [Hj. Matzke, Science of advanced LMFBR fuels, Solid State Physics, Chemistry and Technology of Carbides, Nitrides and Carbonitrides of Uranium and Plutonium, North-Holland, 1986].

Cenozoic tectonic reorganizations of the Death Valley region, southeast California and southwest Nevada

USGS Publications Warehouse

Fridrich, Christopher J.; Thompson, Ren A.

2011-01-01

The Death Valley region, of southeast California and southwest Nevada, is distinct relative to adjacent regions in its structural style and resulting topography, as well as in the timing of basin-range extension. Cenozoic basin-fill strata, ranging in age from greater than or equal to 40 to approximately 2 million years are common within mountain-range uplifts in this region. The tectonic fragmentation and local uplift of these abandoned basin-fills indicate a multistage history of basin-range tectonism. Additionally, the oldest of these strata record an earlier, pre-basin-range interval of weak extension that formed broad shallow basins that trapped sediments, without forming basin-range topography. The Cenozoic basin-fill strata record distinct stratigraphic breaks that regionally cluster into tight age ranges, constrained by well-dated interbedded volcanic units. Many of these stratigraphic breaks are long recognized formation boundaries. Most are angular unconformities that coincide with abrupt changes in depositional environment. Deposits that bound these unconformities indicate they are weakly diachronous; they span about 1 to 2 million years and generally decrease in age to the west within individual basins and regionally, across basin boundaries. Across these unconformities, major changes are found in the distribution and provenance of basin-fill strata, and in patterns of internal facies. These features indicate rapid, regionally coordinated changes in strain patterns defined by major active basin-bounding faults, coincident with step-wise migrations of the belt of active basin-range tectonism. The regionally correlative unconformities thus record short intervals of radical tectonic change, here termed "tectonic reorganizations." The intervening, longer (about 3- to 5-million-year) interval of gradual, monotonic evolution in the locus and style of tectonism are called "tectonic stages." The belt of active tectonism in the Death Valley region has abruptly stepped westward during three successive tectonic reorganizations that intervened between four stages of basin-range tectonism, the youngest of which is ongoing. These three tectonic reorganizations also intervened between four stages of volcanic activity, each of which has been distinct in the compositions of magmas erupted, in eruption rates, and in the locus of volcanic activity—which has stepped progressively westward, in close coordination with the step-wise migrations in the locus of basin-range extension. The timing of the Cenozoic tectonic reorganizations in the Death Valley region correlates closely with the documented timing of episodic reorganizations of the boundary between the Pacific and North American plates, to the west and southwest. This supports models that explain the widely distributed transtensional tectonism in southwestern North America since approximately 40 million years ago as resulting from traction imposed by the adjacent, divergent Pacific plate.

The role of extracellular DNA in uranium precipitation and biomineralisation.

PubMed

Hufton, Joseph; Harding, John H; Romero-González, Maria E

2016-10-26

Bacterial extra polymeric substances (EPS) have been associated with the extracellular precipitation of uranium. Here we report findings on the biomineralisation of uranium, with extracellular DNA (eDNA) used as a model biomolecule representative of EPS. The complexation and precipitation of eDNA with uranium were investigated as a function of pH, ionic strength and varying concentrations of reactants. The role of phosphate moieties in the biomineralisation mechanism was studied by enzymatically releasing phosphate (ePO 4 ) from eDNA compared to abiotic phosphate (aPO 4 ). The eDNA-uranium precipitates and uranium minerals obtained were characterised by Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FT-IR) spectroscopy, Scanning Electron Microscopy-Energy Dispersive X-Ray analysis (SEM-EDX), X-Ray Powder Diffraction (XRD) and X-Ray Photoelectron Spectroscopy (XPS). ATR-FT-IR showed that at pH 5, the eDNA-uranium precipitation mechanism was predominantly mediated by interactions with phosphate moieties from eDNA. At pH 2, the uranium interactions with eDNA occur mainly through phosphate. The solubility equilibrium was dependent on pH with the formation of precipitate reduced as the pH increased. The XRD data confirmed the formation of a uranium phosphate precipitate when synthesised using ePO 4 . XPS and SEM-EDX studies showed the incorporation of carbon and nitrogen groups from the enzymatic orthophosphate hydrolysis on the obtained precipitated. These results suggested that the removal of uranium from solution occurs via two mechanisms: complexation by eDNA molecules and precipitation of a uranium phosphate mineral of the type (UO 2 HPO 4 )·xH 2 O by enzymatic orthophosphate hydrolysis. This demonstrated that eDNA from bacterial EPS is a key contributor to uranium biomineralisation.

Mortality (1968-2008) in a French cohort of uranium enrichment workers potentially exposed to rapidly soluble uranium compounds.

PubMed

Zhivin, Sergey; Guseva Canu, Irina; Samson, Eric; Laurent, Olivier; Grellier, James; Collomb, Philippe; Zablotska, Lydia B; Laurier, Dominique

2016-03-01

Until recently, enrichment of uranium for civil and military purposes in France was carried out by gaseous diffusion using rapidly soluble uranium compounds. We analysed the relationship between exposure to soluble uranium compounds and exposure to external γ-radiation and mortality in a cohort of 4688 French uranium enrichment workers who were employed between 1964 and 2006. Data on individual annual exposure to radiological and non-radiological hazards were collected for workers of the AREVA NC, CEA and Eurodif uranium enrichment plants from job-exposure matrixes and external dosimetry records, differentiating between natural, enriched and depleted uranium. Cause-specific mortality was compared with the French general population via standardised mortality ratios (SMR), and was analysed via Poisson regression using log-linear and linear excess relative risk models. Over the period of follow-up, 131 161 person-years at risk were accrued and 21% of the subjects had died. A strong healthy worker effect was observed: all causes SMR=0.69, 95% CI 0.65 to 0.74. SMR for pleural cancer was significantly increased (2.3, 95% CI 1.06 to 4.4), but was only based on nine cases. Internal uranium and external γ-radiation exposures were not significantly associated with any cause of mortality. This is the first study of French uranium enrichment workers. Although limited in statistical power, further follow-up of this cohort, estimation of internal uranium doses and pooling with similar cohorts should elucidate potential risks associated with exposure to soluble uranium compounds. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

National Uranium Resource Evaluation. Volume 1. Summary of the geology and uranium potential of Precambrian conglomerates in southeastern Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karlstrom, K.E.; Houston, R.S.; Flurkey, A.J.

1981-02-01

A series of uranium-, thorium-, and gold-bearing conglomerates in Late Archean and Early Proterozoic metasedimentary rocks have been discovered in southern Wyoming. The mineral deposits were found by applying the time and strata bound model for the origin of uranium-bearing quartz-pebble conglomerates to favorable rock types within a geologic terrane known from prior regional mapping. No mineral deposits have been discovered that are of current (1981) economic interest, but preliminary resource estimates indicate that over 3418 tons of uranium and over 1996 tons of thorium are present in the Medicine Bow Mountains and that over 440 tons of uranium andmore » 6350 tons of thorium are present in Sierra Madre. Sampling has been inadequate to determine gold resources. High grade uranium deposits have not been detected by work to date but local beds of uranium-bearing conglomerate contain as much as 1380 ppM uranium over a thickness of 0.65 meters. This project has involved geologic mapping at scales from 1/6000 to 1/50,000 detailed sampling, and the evaluation of 48 diamond drill holes, but the area is too large to fully establish the economic potential with the present information. This first volume summarizes the geologic setting and geologic and geochemical characteristics of the uranium-bearing conglomerates. Volume 2 contains supporting geochemical data, lithologic logs from 48 drill holes in Precambrian rocks, and drill site geologic maps and cross-sections from most of the holes. Volume 3 is a geostatistical resource estimate of uranium and thorium in quartz-pebble conglomerates.« less

Uranium chemistry in stack solutions and leachates of phosphogypsum disposed at a coastal area in Cyprus.

PubMed

Lysandrou, M; Pashalidis, I

2008-02-01

The effect of the matrix composition (main constituents) on the concentration and chemical behavior of uranium in phosphogypsum stack solutions and leachates has been investigated. Solid and aqueous samples were taken from three different sub-areas of a phosphogypsum stack at a coastal area in Vasilikos (Cyprus). The sub-areas are characterized whether by their acidity (e.g. "aged" and "non-aged" phosphogypsum) or by their salt content, originating from pulping water during wet stacking or (after deposition) from the adjacent sea. Measurements in stack solutions and leachates showed that phosphogypsum characteristics affect both, the concentration and the chemical behavior of uranium in solution. Uranium concentration in solutions of increased salinity is up to three orders of magnitude higher than in solutions of low salinity and this is attributed to the effect of ionic strength on the solubility of phosphogypsum. Modelling showed that uranium in stack solutions is predominantly present in the form of uranium(VI) phosphate complexes (e.g. UO(2)(H(2)PO(4))(2), UO(2)HPO(4)), whereas in leachates uranium(VI) fluoro complexes (e.g. UO(2)F(2), UO(2)F(3)(-)) are predominant in solution. The latter indicates that elution of uranium from phosphogypsum takes places most probably in the form of fluoro complexes. Both, effective elution by saline water and direct migration of uranium to the sea, where it forms very stable uranium(VI) carbonato complexes, indicate that the adjacent sea will be the final receptor of uranium released from Vasilikos phosphogypsum.

Francis Perrin's 1939 Analysis of Uranium Criticality

NASA Astrophysics Data System (ADS)

Reed, Cameron

2012-03-01

In May 1939, French physicist Francis Perrin published the first numerical estimate of the fast-neutron critical mass of a uranium compound. While his estimate of about 40 metric tons (12 tons if tamped) pertained to uranium oxide of natural isotopic composition as opposed to the enriched uranium that would be required for a nuclear weapon, it is interesting to examine Perrin's physics and to explore the subsequent impact of his paper. In this presentation I will discuss Perrin's model, the likely provenance of his parameter values, and how his work compared to the approach taken by Robert Serber in his 1943 Los Alamos Primer.

Uranium Release from Acidic Weathered Hanford Sediments: Single-Pass Flow-Through and Column Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Guohui; Um, Wooyong; Wang, Zheming

The reaction of acidic radioactive waste with sediments can induce mineral transformation reactions that, in turn, control contaminant fate. Here, sediment weathering by synthetic uranium-containing acid solutions was investigated using bench-scale experiments to simulate waste disposal conditions at Hanford’s cribs, USA. During acid weathering, the presence of phosphate exerted a strong influence over uranium mineralogy and a rapidly precipitated, crystalline uranium phosphate phase (meta-ankoleite [K(UO2)(PO4)·3H2O]) was identified using spectroscopic and diffraction-based techniques. In phosphate-free system, uranium oxyhydroxide minerals such as K-compreignacite [K2(UO2)6O4(OH)6·7H2O] were formed. Single-pass flow-through (SPFT) and column leaching experiments using synthetic Hanford pore water showed that uranium precipitatedmore » as meta-ankoleite during acid weathering was strongly retained in the sediments, with an average release rate of 2.67E-12 mol g-1 s-1. In the absence of phosphate, uranium release was controlled by dissolution of uranium oxyhydroxide (compreignacite-type) mineral with a release rate of 1.05-2.42E-10 mol g-1 s-1. The uranium mineralogy and release rates determined for both systems in this study support the development of accurate U-release models for prediction of contaminant transport. These results suggest that phosphate minerals may be a good candidate for uranium remediation approaches at contaminated sites.« less

Uranium Release from Acidic Weathered Hanford Sediments: Single-Pass Flow-Through and Column Experiments.

PubMed

Wang, Guohui; Um, Wooyong; Wang, Zheming; Reinoso-Maset, Estela; Washton, Nancy M; Mueller, Karl T; Perdrial, Nicolas; O'Day, Peggy A; Chorover, Jon

2017-10-03

The reaction of acidic radioactive waste with sediments can induce mineral transformation reactions that, in turn, control contaminant fate. Here, sediment weathering by synthetic uranium-containing acid solutions was investigated using bench-scale experiments to simulate waste disposal conditions at Hanford's cribs (Hanford, WA). During acid weathering, the presence of phosphate exerted a strong influence over uranium mineralogy and a rapidly precipitated, crystalline uranium phosphate phase (meta-ankoleite [K(UO 2 )(PO 4 )·3H 2 O]) was identified using spectroscopic and diffraction-based techniques. In phosphate-free system, uranium oxyhydroxide minerals such as K-compreignacite [K 2 (UO 2 ) 6 O 4 (OH) 6 ·7H 2 O] were formed. Single-pass flow-through (SPFT) and column leaching experiments using synthetic Hanford pore water showed that uranium precipitated as meta-ankoleite during acid weathering was strongly retained in the sediments, with an average release rate of 2.67 × 10 -12 mol g -1 s -1 . In the absence of phosphate, uranium release was controlled by dissolution of uranium oxyhydroxide (compreignacite-type) mineral with a release rate of 1.05-2.42 × 10 -10 mol g -1 s -1 . The uranium mineralogy and release rates determined for both systems in this study support the development of accurate U-release models for the prediction of contaminant transport. These results suggest that phosphate minerals may be a good candidate for uranium remediation approaches at contaminated sites.

Sensitivity Analysis and Parameter Estimation for a Reactive Transport Model of Uranium Bioremediation

NASA Astrophysics Data System (ADS)

Meyer, P. D.; Yabusaki, S.; Curtis, G. P.; Ye, M.; Fang, Y.

2011-12-01

A three-dimensional, variably-saturated flow and multicomponent biogeochemical reactive transport model of uranium bioremediation was used to generate synthetic data . The 3-D model was based on a field experiment at the U.S. Dept. of Energy Rifle Integrated Field Research Challenge site that used acetate biostimulation of indigenous metal reducing bacteria to catalyze the conversion of aqueous uranium in the +6 oxidation state to immobile solid-associated uranium in the +4 oxidation state. A key assumption in past modeling studies at this site was that a comprehensive reaction network could be developed largely through one-dimensional modeling. Sensitivity analyses and parameter estimation were completed for a 1-D reactive transport model abstracted from the 3-D model to test this assumption, to identify parameters with the greatest potential to contribute to model predictive uncertainty, and to evaluate model structure and data limitations. Results showed that sensitivities of key biogeochemical concentrations varied in space and time, that model nonlinearities and/or parameter interactions have a significant impact on calculated sensitivities, and that the complexity of the model's representation of processes affecting Fe(II) in the system may make it difficult to correctly attribute observed Fe(II) behavior to modeled processes. Non-uniformity of the 3-D simulated groundwater flux and averaging of the 3-D synthetic data for use as calibration targets in the 1-D modeling resulted in systematic errors in the 1-D model parameter estimates and outputs. This occurred despite using the same reaction network for 1-D modeling as used in the data-generating 3-D model. Predictive uncertainty of the 1-D model appeared to be significantly underestimated by linear parameter uncertainty estimates.

Electron transfer at the cell-uranium interface in Geobacter spp.

PubMed

Reguera, Gemma

2012-12-01

The in situ stimulation of Fe(III) oxide reduction in the subsurface stimulates the growth of Geobacter spp. and the precipitation of U(VI) from groundwater. As with Fe(III) oxide reduction, the reduction of uranium by Geobacter spp. requires the expression of their conductive pili. The pili bind the soluble uranium and catalyse its extracellular reductive precipitation along the pili filaments as a mononuclear U(IV) complexed by carbon-containing ligands. Although most of the uranium is immobilized by the pili, some uranium deposits are also observed in discreet regions of the outer membrane, consistent with the participation of redox-active foci, presumably c-type cytochromes, in the extracellular reduction of uranium. It is unlikely that cytochromes released from the outer membrane could associate with the pili and contribute to the catalysis, because scanning tunnelling microscopy spectroscopy did not reveal any haem-specific electronic features in the pili, but, rather, showed topographic and electronic features intrinsic to the pilus shaft. Pili not only enhance the rate and extent of uranium reduction per cell, but also prevent the uranium from traversing the outer membrane and mineralizing the cell envelope. As a result, pili expression preserves the essential respiratory activities of the cell envelope and the cell's viability. Hence the results support a model in which the conductive pili function as the primary mechanism for the reduction of uranium and cellular protection in Geobacter spp.

Uranium plume persistence impacted by hydrologic and geochemical heterogeneity in the groundwater and river water interaction zone of Hanford site

NASA Astrophysics Data System (ADS)

Chen, X.; Zachara, J. M.; Vermeul, V. R.; Freshley, M.; Hammond, G. E.

2015-12-01

The behavior of a persistent uranium plume in an extended groundwater- river water (GW-SW) interaction zone at the DOE Hanford site is dominantly controlled by river stage fluctuations in the adjacent Columbia River. The plume behavior is further complicated by substantial heterogeneity in physical and geochemical properties of the host aquifer sediments. Multi-scale field and laboratory experiments and reactive transport modeling were integrated to understand the complex plume behavior influenced by highly variable hydrologic and geochemical conditions in time and space. In this presentation we (1) describe multiple data sets from field-scale uranium adsorption and desorption experiments performed at our experimental well-field, (2) develop a reactive transport model that incorporates hydrologic and geochemical heterogeneities characterized from multi-scale and multi-type datasets and a surface complexation reaction network based on laboratory studies, and (3) compare the modeling and observation results to provide insights on how to refine the conceptual model and reduce prediction uncertainties. The experimental results revealed significant spatial variability in uranium adsorption/desorption behavior, while modeling demonstrated that ambient hydrologic and geochemical conditions and heterogeneities in sediment physical and chemical properties both contributed to complex plume behavior and its persistence. Our analysis provides important insights into the characterization, understanding, modeling, and remediation of groundwater contaminant plumes influenced by surface water and groundwater interactions.

Effects of aqueous uranyl speciation on the kinetics of microbial uranium reduction

DOE PAGES

Belli, Keaton M.; DiChristina, Thomas J.; Van Cappellen, Philippe; ...

2015-02-16

The ability to predict the success of the microbial reduction of soluble U(VI) to highly insoluble U(IV) as an in situ bioremediation strategy is complicated by the wide range of geochemical conditions at contaminated sites and the strong influence of aqueous uranyl speciation on the bioavailability and toxicity of U(VI) to metal-reducing bacteria. In order to determine the effects of aqueous uranyl speciation on uranium bioreduction kinetics, incubations and viability assays with Shewanella putrefaciens strain 200 were conducted over a range of pH and dissolved inorganic carbon (DIC), Ca 2+, and Mg 2+ concentrations. A speciation-dependent kinetic model was developedmore » to reproduce the observed time series of total dissolved uranium concentration over the range of geochemical conditions tested. The kinetic model yielded the highest rate constant for the reduction of uranyl non-carbonate species (i.e., the ‘free’ hydrated uranyl ion, uranyl hydroxides, and other minor uranyl complexes), indicating that they represent the most readily reducible fraction of U(VI) despite being the least abundant uranyl species in solution. In the presence of DIC, Ca 2+, and Mg 2+ is suppressed during the formation of more bioavailable uranyl non-carbonate species and resulted in slower bioreduction rates. At high concentrations of bioavailable U(VI), however, uranium toxicity to S. putrefaciens inhibited bioreduction, and viability assays confirmed that the concentration of non-carbonate uranyl species best predicts the degree of toxicity. The effect of uranium toxicity was accounted for by incorporating the free ion activity model of metal toxicity into the bioreduction rate law. These results demonstrate that, in the absence of competing terminal electron acceptors, uranium bioreduction kinetics can be predicted over a wide range of geochemical conditions based on the bioavailability and toxicity imparted on U(VI) by solution composition. Finally, these findings also imply that the concentration of uranyl non-carbonate species, despite being extremely low, is a determining factor controlling uranium bioreduction at contaminated sites.« less

Monte Carlo modeling of recrystallization processes in α-uranium

DOE PAGES

Steiner, M. A.; McCabe, R. J.; Garlea, E.; ...

2017-08-01

In this study, starting with electron backscattered diffraction (EBSD) data obtained from a warm clock-rolled α-uranium deformation microstructure, a Potts Monte Carlo model was used to simulate static site-saturated recrystallization while testing a number of different conditions for the assignment of recrystallized nuclei within the microstructure. The simulations support observations that recrystallized nuclei within α-uranium form preferentially on non-twin high-angle grain boundary sites at 450 °C, and demonstrate that the most likely nucleation sites on these boundaries can be identified by the surrounding degree of Kernel Average Misorientation (KAM), which may be considered as a proxy for the local geometricallymore » necessary dislocation (GND) density.« less

Development and Validation of Capabilities to Measure Thermal Properties of Layered Monolithic U-Mo Alloy Plate-Type Fuel

NASA Astrophysics Data System (ADS)

Burkes, Douglas E.; Casella, Andrew M.; Buck, Edgar C.; Casella, Amanda J.; Edwards, Matthew K.; MacFarlan, Paul J.; Pool, Karl N.; Smith, Frances N.; Steen, Franciska H.

2014-07-01

The uranium-molybdenum (U-Mo) alloy in a monolithic form has been proposed as one fuel design capable of converting some of the world's highest power research reactors from the use of high enriched uranium to low enriched uranium. One aspect of the fuel development and qualification process is to demonstrate appropriate understanding of the thermal-conductivity behavior of the fuel system as a function of temperature and expected irradiation conditions. The purpose of this paper is to verify functionality of equipment installed in hot cells for eventual measurements on irradiated uranium-molybdenum (U-Mo) monolithic fuel specimens, refine procedures to operate the equipment, and validate models to extract the desired thermal properties. The results presented here demonstrate the adequacy of the equipment, procedures, and models that have been developed for this purpose based on measurements conducted on surrogate depleted uranium-molybdenum (DU-Mo) alloy samples containing a Zr diffusion barrier and clad in aluminum alloy 6061 (AA6061). The results are in excellent agreement with thermal property data reported in the literature for similar U-Mo alloys as a function of temperature.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamlin, H.S.; Dutton, S.P.; Tyler, N.

The Tirrawarra Sandstone contains 146 million bbl of oil in Tirrawarra field in the Cooper basin of South Australia. We used core, well logs, and petro-physical data to construct a depositional-facies-based flow-unit model of the reservoir, which describes rock properties and hydrocarbon saturations in three dimensions. Using the model to calculate volumes and residency of original and remaining oil in place, we identified an additional 36 million bbl of oil in place and improved understanding of past production patterns. The Tirrawarra Sandstone reservoir was deposited in a Carboniferous-Permian proglacial intracratonic setting and is composed of lacustrine and fluvial facies assemblages.more » The stratigraphic framework of these nonmarine facies is defined by distinctive stacking patterns and erosional unconformities. Mudstone dominated zones that are analogous to marine maximum flooding surfaces bound the reservoir. At its base a progradational lacustrine-delta system, composed of lenticular mud-clast-rich sandstones enclosed in mudstone, is truncated by an unconformity. Sandstones in these lower deltaic facies lost most of their porosity by mechanical compaction of ductile grains. Sediment reworking by channel migration and locally shore-zone processes created by quartz-rich, multilateral sandstones, which retained the highest porosity and permeability of all the reservoir facies and contained most of the original oil in place. Braided-channel sandstones, however, are overlain by lenticular meandering-channel sandstones, which in turn grade upward into widespread mudstones and coals. Thus, this uppermost part of the reservoir displays a retrogradational stacking pattern and upward-decreasing reservoir quality. Our results demonstrate that depositional variables are the primary controls on reservoir quality and productivity in the Tirrawarra Sandstone.« less

Simplified behaviors from increased heterogeneity: I. 2-D uranium transport experiments at the decimeter scale.

PubMed

Miller, Andrew W; Rodriguez, Derrick R; Honeyman, Bruce D

2013-05-01

Intermediate scale tank studies were conducted to examine the effects of physical heterogeneity of aquifer material on uranium desorption and subsequent transport in order to bridge the scaling gap between bench and field scale systems. Uranium contaminated sediment from a former uranium mill field site was packed into two 2-D tanks with internal dimensions of 2.44×1.22×0.076 m (tank 1) and 2.44×0.61×0.076 m (tank 2). Tank 1 was packed in a physically homogenous manner, and tank 2 was packed with long lenses of high and low conductivities resulting in different flow fields within the tanks. Chemical gradients within the flow domain were altered by temporal changes in influent water chemistry. The uranium source was desorption from the sediment. Despite the physical differences in the flow fields, there were minimal differences in global uranium leaching behavior between the two tanks. The dominant uranium species in both tanks over time and space was Ca2UO2(CO3)3(0). However, the uranium/alkalinity relationships varied as a function of time in tank 1 and were independent of time in tank 2. After planned stop-flow events, small, short-lived rebounds were observed in tank 1 while no rebound of uranium concentrations was observed in tank 2. Despite appearing to be in local equilibrium with respect to uranium desorption, a previously derived surface complexation model was insufficient to describe uranium partitioning within the flow domain. This is the first in a pair of papers; the companion paper presents an intermediate scale 3-D tank experiment and inter-tank comparisons. For these systems, physical heterogeneity at or above the decimeter scale does not affect global scale uranium desorption and transport. Instead, uranium fluxes are controlled by chemistry dependent desorption patterns induced by changing the influent ionic composition. Published by Elsevier B.V.

Simplified behaviors from increased heterogeneity: I. 2-D uranium transport experiments at the decimeter scale

NASA Astrophysics Data System (ADS)

Miller, Andrew W.; Rodriguez, Derrick R.; Honeyman, Bruce D.

2013-05-01

Intermediate scale tank studies were conducted to examine the effects of physical heterogeneity of aquifer material on uranium desorption and subsequent transport in order to bridge the scaling gap between bench and field scale systems. Uranium contaminated sediment from a former uranium mill field site was packed into two 2-D tanks with internal dimensions of 2.44 × 1.22 × 0.076 m (tank 1) and 2.44 × 0.61 × 0.076 m (tank 2). Tank 1 was packed in a physically homogenous manner, and tank 2 was packed with long lenses of high and low conductivities resulting in different flow fields within the tanks. Chemical gradients within the flow domain were altered by temporal changes in influent water chemistry. The uranium source was desorption from the sediment. Despite the physical differences in the flow fields, there were minimal differences in global uranium leaching behavior between the two tanks. The dominant uranium species in both tanks over time and space was Ca2UO2(CO3)30. However, the uranium/alkalinity relationships varied as a function of time in tank 1 and were independent of time in tank 2. After planned stop-flow events, small, short-lived rebounds were observed in tank 1 while no rebound of uranium concentrations was observed in tank 2. Despite appearing to be in local equilibrium with respect to uranium desorption, a previously derived surface complexation model was insufficient to describe uranium partitioning within the flow domain. This is the first in a pair of papers; the companion paper presents an intermediate scale 3-D tank experiment and inter-tank comparisons. For these systems, physical heterogeneity at or above the decimeter scale does not affect global scale uranium desorption and transport. Instead, uranium fluxes are controlled by chemistry dependent desorption patterns induced by changing the influent ionic composition.

Variably Saturated Flow and Multicomponent Biogeochemical Reactive Transport Modeling of a Uranium Bioremediation Field Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yabusaki, Steven B.; Fang, Yilin; Williams, Kenneth H.

2011-11-01

Field experiments at a former uranium mill tailings site have identified the potential for stimulating indigenous bacteria to catalyze the conversion of aqueous uranium in the +6 oxidation state to immobile solid-associated uranium in the +4 oxidation state. This effectively removes uranium from solution resulting in groundwater concentrations below actionable standards. Three-dimensional, coupled variably-saturated flow and biogeochemical reactive transport modeling of a 2008 in situ uranium bioremediation field experiment is used to better understand the interplay of transport rates and biogeochemical reaction rates that determine the location and magnitude of key reaction products. A comprehensive reaction network, developed largely throughmore » previous 1-D modeling studies, was used to simulate the impacts on uranium behavior of pulsed acetate amendment, seasonal water table variation, spatially-variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. A principal challenge is the mechanistic representation of biologically-mediated terminal electron acceptor process (TEAP) reactions whose products significantly alter geochemical controls on uranium mobility through increases in pH, alkalinity, exchangeable cations, and highly reactive reduction products. In general, these simulations of the 2008 Big Rusty acetate biostimulation field experiment in Rifle, Colorado confirmed previously identified behaviors including (1) initial dominance by iron reducing bacteria that concomitantly reduce aqueous U(VI), (2) sulfate reducing bacteria that become dominant after {approx}30 days and outcompete iron reducers for the acetate electron donor, (3) continuing iron-reducer activity and U(VI) bioreduction during dominantly sulfate reducing conditions, and (4) lower apparent U(VI) removal from groundwater during dominantly sulfate reducing conditions. New knowledge on simultaneously active metal and sulfate reducers has been incorporated into the modeling. In this case, an initially small population of slow growing sulfate reducers is active from the initiation of biostimulation. Three-dimensional, variably saturated flow modeling was used to address impacts of a falling water table during acetate injection. These impacts included a significant reduction in aquifer saturated thickness and isolation of residual reactants and products, as well as unmitigated uranium, in the newly unsaturated vadose zone. High permeability sandy gravel structures resulted in locally high flow rates in the vicinity of injection wells that increased acetate dilution. In downgradient locations, these structures created preferential flow paths for acetate delivery that enhanced local zones of TEAP reactivity and subsidiary reactions. Conversely, smaller transport rates associated with the lower permeability lithofacies (e.g., fine) and vadose zone were shown to limit acetate access and reaction. Once accessed by acetate, however, these same zones limited subsequent acetate dilution and provided longer residence times that resulted in higher concentrations of TEAP products when terminal electron donors and acceptors were not limiting. Finally, facies-based porosity and reactive surface area variations were shown to affect aqueous uranium concentration distributions; however, the ranges were sufficiently small to preserve general trends. Large computer memory and high computational performance were required to simulate the detailed coupled process models for multiple biogeochemical components in highly resolved heterogeneous materials for the 110-day field experiment and 50 days of post-biostimulation behavior. In this case, a highly-scalable subsurface simulator operating on 128 processor cores for 12 hours was used to simulate each realization. An equivalent simulation without parallel processing would have taken 60 days, assuming sufficient memory was available.« less

Systemic Lupus Erythematosus is Associated with Uranium Exposure in a Community Living Near a Uranium Processing Plant: A Nested Case-Control Study

PubMed Central

Lu-Fritts, Pai-Yue; Kottyan, Leah C.; James, Judith A.; Xie, Changchung; Buckholz, Jeanette M.; Pinney, Susan M.; Harley, John B.

2014-01-01

Objective Explore the hypothesis that cases of SLE will be found more frequently in community members with high prior uranium exposure in the Fernald Community Cohort (FCC). Methods A nested case control study was performed. The FCC is a volunteer population that lived near a uranium ore processing plant in Fernald, Ohio, USA during plant operation and members were monitored for 18 years. Uranium plant workers were excluded. SLE cases were identified using American College of Rheumatology classification criteria, laboratory testing, and medical record review. Each case was matched to four age-, race-, and sex-matched controls. Sera from potential cases and controls were screened for autoantibodies. Cumulative uranium particulate exposure was calculated using a dosimetry model. Logistic regression with covariates was used to calculate odds ratios (OR) with 95% confidence intervals (CI). Results The FCC includes 4,187 individuals with background uranium exposure, 1,273 with moderate exposure, and 2,756 with higher exposure. SLE was confirmed in 23 of 31 individuals with a lupus ICD9 code, and in 2 of 43 other individuals prescribed hydroxychloroquine. The female:male ratio was 5.25:1. Of the 25 SLE cases, 12 were in the higher exposure group. SLE was associated with higher uranium exposure (OR 3.92, 95% CI 1.131-13.588, p = 0.031). Conclusion High uranium exposure is associated with SLE relative to matched controls in this sample of uranium exposed individuals. Potential explanations for this relationship include possible autoimmune or estrogen effects of uranium, somatic mutation, epigenetic effects, or effects of some other unidentified accompanying exposure. PMID:25103365

Background and Source Term Identification in Active Neutron Interrogation Methods

DTIC Science & Technology

2011-03-24

interactions occurred to observe gamma ray peaks and not unduly increase simulation time. Not knowing the uranium enrichment modeled by Gozani, pure U...neutron interactions can occur. The uranium targets, though, should have increased neutron fluencies as the energy levels become below 2 MeV. This is...Assessment Monitor Site (TEAMS) at Kirtland AFB, NM. Iron (Fe-56), lead (Pb-207), polyethylene (C2H4 –– > C-12 & H-1), and uranium (U-235 and U-238) were

Investigation of uranium molecular species using laser ablation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curreli, Davide

2017-07-12

The goal of this project is to investigate the dynamic evolution of uranium oxide (UOx) molecular species in a rapidly cooling low-temperature plasma using a coupled experimental and modeling approach. Our purpose is to develop quantitative constraints on the UOx phase chemistry under physical conditions similar to that of a nuclear fireball at the time of debris condensation. This work is motivated by a need to better understand the factors controlling uranium chemical fractionation in post-detonation nuclear debris.

Uranium biosorption by Padina sp. algae biomass: kinetics and thermodynamics.

PubMed

Khani, Mohammad Hassan

2011-11-01

Kinetic, thermodynamic, and equilibrium isotherms of the biosorption of uranium ions onto Padina sp., a brown algae biomass, in a batch system have been studied. The kinetic data were found to follow the pseudo-second-order model. Intraparticle diffusion is not the sole rate-controlling factor. The equilibrium experimental results were analyzed in terms of Langmuir isotherm depending with temperature. Equilibrium data fitted very well to the Langmuir model. The maximum uptakes estimated by using the Langmuir model were 434.8, 416.7, 400.0, and 370.4 mg/g at 10°C, 20°C, 30°C, and 40°C, respectively. Gibbs free energy was spontaneous for all interactions, and the adsorption process exhibited exothermic enthalpy values. Padina sp. algae were shown to be a favorable biosorbent for uranium removal from aqueous solutions.

Round-robin 230Th– 234U age dating of bulk uranium for nuclear forensics

DOE PAGES

Gaffney, Amy M.; Hubert, Amélie; Kinman, William S.; ...

2015-07-30

We report that in an inter-laboratory measurement comparison study, four laboratories determined 230Th– 234U model ages of uranium certified reference material NBL U050 using isotope dilution mass spectrometry. The model dates determined by the participating laboratories range from 9 March 1956 to 19 October 1957, and are indistinguishable given the associated measurement uncertainties. These model ages are concordant with to slightly older than the known production age of NBL U050.

Round-robin 230Th– 234U age dating of bulk uranium for nuclear forensics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaffney, Amy M.; Hubert, Amélie; Kinman, William S.

We report that in an inter-laboratory measurement comparison study, four laboratories determined 230Th– 234U model ages of uranium certified reference material NBL U050 using isotope dilution mass spectrometry. The model dates determined by the participating laboratories range from 9 March 1956 to 19 October 1957, and are indistinguishable given the associated measurement uncertainties. These model ages are concordant with to slightly older than the known production age of NBL U050.

Long lasting paleolandscapes stability of the French Massif Central during the Mesozoic

NASA Astrophysics Data System (ADS)

Ricordel-Prognon, C.; Thiry, M.; Theveniaut, H.; Lagroix, F.

2009-04-01

Regional geodynamical evolution is mainly constrained by the sedimentary record in the basins. Usually, little is known about geodynamics of the peripheral areas and even less on the evolution of the basement areas. Continental unconformities are essential to estimate erosion rates of basement and to model the crustal dynamics that control subsidence of surrounding sedimentary basins but also uplift and erosion on their edges. Dating such unconformities has always been the stumbling block while it is a prerequisite to constrain geodynamical models. Paleomagnetism has been proven as a suitable tool to date ferrugineous paleoweathering features. The method has been applied to paleoweathering occurrences resting on the Massif Central crystalline basement as well as to paleoweathering features affecting the crystalline basement itself. The remanence measurements were obtained at the Paleomagnetic Laboratory of the Institut Physique du Globe de Paris and data analyses were carried out using PaleoMac 5 software (Cogné, 2003). Relative dating of the paleoweathering profiles have been acquired by comparing the recorded paleomagnetic poles from the analysed samples to the apparent polar wandering path of the Eurasian plate (Edel et Duringer, 1997 ; Besse and Courtillot, 2003). Thick red kaolinitic formations rest locally on the Massif Central basement. They are generally bounded by the Tertiary grabens and buried by the Oligocene formations. Thus these azoic red formations have classically been ascribed to the "Siderolithic" formations of Eocene-Oligocene age. They show many pedogenic features (termites burrows, illuviation and hydromorphic features and nodules) and strong relationships with paleolandscape organisation (leaned against fault scarps, infilling paleovalleys, etc.). Macro and micromorphological arrangements show that these formations are in situ paleosols. Paleomagnetic ages range from 160 Ma (Late Jurassic) in the centre of the Massif Central to 140 Ma (Early Cretaceous) in the northern parts of the massif (Ricordel et al., 2005; Ricordel, 2007;). These new ages, fairly older than the expected ones, bring considerable changes in the palaeogeographic evolution of the Massif Central during Mesozoic and Cenozoic. Basement rocks (granites, gneiss, rhyolites and even Permo-Carboniferous sediments) show often pinkish facies throughout the Massif Central. It has been shown that these pink facies are albitised (mainly pseudomorphic replacement of the primary plagioclases into albite and alteration of the biotite into chlorite) (Schmitt, 1992; Parcerisa et al., 2009). These albitised facies are arranged in a clear succession against (?) the Triassic unconformity that gives significant constraints about their development in relation with the Triassic palaeosurface. Secondary albite and chlorite contain minute hematite inclusions, which have been dated, using paleomagnetism, to be Triassic in age (245 Ma) (Ricordel et al., 2007). Given that the alterations are of the same age as the unconformity, it then follows that the albitised facies be related to the Triassic palaeosurface and be used to track back the Triassic palaeosurface through wide crystalline areas, even far away from the Mesozoic cover. Palaeomagnetic analyses allowed dating a large range of paleoweathering features for which no objective datings were previously available. Spatial and temporal distributions of the paleoweathering features and related unconformities provide key arguments to unravel the geodynamic evolution of the Massif Central. Triassic, Late Jurassic and Tertiary unconformities are superimposed on large areas of the Massif Centrall. This implies very little erosion of the crystalline basement since Triassic time, as shown by the widespread preservation of the Triassic albitized facies. Since the red kaolinitic paleosols of Late Jurassic/Early Cretaceous age rest directly on the basement rocks, large areas of the Massif Central were uncovered at this period, and more importantly no Jurassic cover was preserved (if such a cover was even deposited?) on the massif. Consequently, the Massif Central probably never did support an important (more than 500 m) sedimentary cover during the Mesozoic. These paleosurface ages provide important constraints to crustal dynamics modeling. Identification and dating of the successive continental unconformities are evidence for long lasting continental evolution and landscape stability of large areas of the Massif Central during the Mesozoic. The alternative hypothesis was that the Massif Central was subsidizing during Mesozoic time and covered with a 2,000 m thick sedimentary series, which was fairly quickly eroded during early Tertiary (Barbarand et al., 2001). In the future, making substantial progress in paleoweathering profiles dating, especially in the scope of improving time resolution, will allow attempting efficient correlation between the continental records and the diverse processes involved in their development (eustatism, climate, global and regional tectonics). Moreover, progress in dating paleoweathering features and continental azoic deposits, will allow to develop a "continental stratigraphy" of climatic and geomorphological events and to establish a mass balances between weathering/erosion weathering/erosion on land and deposition in basins. References Barbarand J., Lucazeau F., Pagel M., Séranne M., 2001, Burial and exhumation history of the south-eastern Massif Central (France) constrained by apatite fission track thermochronology. Tectonophysics, 335, 3-4, p. 275-290. Besse, J., Courtillot, V., 2003. Apparent true polar wander and the geometry of the geomagnetic field over the last 200 Myr: Correction: Journal of Geophysical Research, 108, p. 2300. Cogné, J.P., 2003. PaleoMac: a MacintoshTM application for treating paleomagnetic data and making plate reconstructions. Geochemistry Geophysics Geosystems, 4 (1), 1007. Edel J.B., Duringer P., 1997, The apparent polar wander path of the European plate in Upper Triassic-Lower Jurassic times and the Liassic intraplate fracturing of the Pangea : New palaeomagnetic constraints from NW France and SW Germany. Geophysical Journal International 128 (2), 331-344. Parcerisa D., Thiry M., Schmitt J.-M., 2009, Albitization related to the Triassic unconformity in igneous rocks of the Morvan Massif (France), International Journal of Earth Sciences, DOI: 10.1007/s00531-008-0405-1 Ricordel C, Parcerisa D, Thiry M, Moreau M-G, Gómez-Gras D (2007) Triassic magnetic overprints related to albitization in granites from the Morvan massif (France). Palaeogeogr Palaeoclimatol Palaeoecol 251: 268-282 Ricordel C. (2007) - Datations par paléomagnétisme des paléoaltérations du Massif central et de ses bordures : implications géodynamiques. Thèse Ecole Nat. Sup. Des Mines de Paris, Paris, 172 p. Ricordel C., Thiry M., Moreau M.-G., Théveniaut H. (2005) Paleomagnetic datings on "Siderolithic" paleoweathering profiles along French Massif Central. European Geosciences Union, Vienne, Autriche, 24-29 avril, Geophysical Research Abstracts, vol. 7, 06631, 6 p. Schmitt J.M. (1992) Triassic albitization in southern France: an unusual mineralogical record from a major continental paleosurface In: Schmitt JM, Gall Q (eds). Mineralogical and geochemical records of paleoweathering. Paris, ENSMP, Mem Sci Terre 18, pp 115-131

Groundwater uranium and cancer incidence in South Carolina

PubMed Central

Wagner, Sara E.; Burch, James B.; Bottai, Matteo; Puett, Robin; Porter, Dwayne; Bolick-Aldrich, Susan; Temples, Tom; Wilkerson, Rebecca C.; Vena, John E.; Hébert, James R.

2012-01-01

Objective This ecologic study tested the hypothesis that census tracts with elevated groundwater uranium and more frequent groundwater use have increased cancer incidence. Methods Data sources included: incident total, leukemia, prostate, breast, colorectal, lung, kidney, and bladder cancers (1996–2005, SC Central Cancer Registry); demographic and groundwater use (1990 US Census); and groundwater uranium concentrations (n = 4,600, from existing federal and state databases). Kriging was used to predict average uranium concentrations within tracts. The relationship between uranium and standardized cancer incidence ratios was modeled among tracts with substantial groundwater use via linear or semiparametric regression, with and without stratification by the proportion of African Americans in each area. Results A total of 134,685 cancer cases were evaluated. Tracts with ≥50% groundwater use and uranium concentrations in the upper quartile had increased risks for colorectal, breast, kidney, prostate, and total cancer compared to referent tracts. Some of these relationships were more likely to be observed among tracts populated primarily by African Americans. Conclusion SC regions with elevated groundwater uranium and more groundwater use may have an increased incidence of certain cancers, although additional research is needed since the design precluded adjustment for race or other predictive factors at the individual level. PMID:21080052

Types of stratigraphic traps in Lower Cretaceous Muddy Formation, northern Powder River Basin, Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lovekin, J.R.; Odland, S.K.; Quartarone, T.S. Gardner, M.H.

1986-08-01

Stratigraphic traps account for most of the oil produced from the Muddy Sandstone in the northern Powder River basin. Two categories of traps exist. The first trap type is the result of lateral and vertical facies changes. Reservoir facies include tidal channels, point bars, bayhead deltas, barrier islands, and strand-plain sandstones; trapping facies include bay-fill and estuarine sediments, mud-filled tidal channels, and flood-plain deposits. The second of the two categories of traps results from an unconformity that juxtaposes permeable and impermeable sediments of quite different ages. Structural and diagenetic factors often modify and locally enhance reservoir quality within both categoriesmore » of stratigraphic traps. The various types of traps are demonstrated by studies of six field areas: (1) barrier-island sandstones, sealed updip by back-barrier shales, produce at Ute and Kitty fields; (2) tidal channels produce at Collums and Kitty fields; (3) bayhead deltas, encased in estuarine sediments, form traps at Oedekoven and Kitty fields; (4) fluvial point-bar sandstones form traps at Oedekoven, Store, and Kitty fields; (5) unconformity-related traps exist where Muddy fluvial valley-fill sediments lap out against impermeable valley walls of Skull Creek Shale on the updip side at Store, Oedekoven, and Kitty fields; and (6) the clay-rich weathered zone, directly beneath an intraformational unconformity, forms the seal to the reservoirs at Amos Draw field.« less

Uranium-series constraints on radionuclide transport and groundwater flow at the Nopal I uranium deposit, Sierra Pena Blanca, Mexico.

PubMed

Goldstein, Steven J; Abdel-Fattah, Amr I; Murrell, Michael T; Dobson, Patrick F; Norman, Deborah E; Amato, Ronald S; Nunn, Andrew J

2010-03-01

Uranium-series data for groundwater samples from the Nopal I uranium ore deposit were obtained to place constraints on radionuclide transport and hydrologic processes for a nuclear waste repository located in fractured, unsaturated volcanic tuff. Decreasing uranium concentrations for wells drilled in 2003 are consistent with a simple physical mixing model that indicates that groundwater velocities are low ( approximately 10 m/y). Uranium isotopic constraints, well productivities, and radon systematics also suggest limited groundwater mixing and slow flow in the saturated zone. Uranium isotopic systematics for seepage water collected in the mine adit show a spatial dependence which is consistent with longer water-rock interaction times and higher uranium dissolution inputs at the front adit where the deposit is located. Uranium-series disequilibria measurements for mostly unsaturated zone samples indicate that (230)Th/(238)U activity ratios range from 0.005 to 0.48 and (226)Ra/(238)U activity ratios range from 0.006 to 113. (239)Pu/(238)U mass ratios for the saturated zone are <2 x 10(-14), and Pu mobility in the saturated zone is >1000 times lower than the U mobility. Saturated zone mobility decreases in the order (238)U approximately (226)Ra > (230)Th approximately (239)Pu. Radium and thorium appear to have higher mobility in the unsaturated zone based on U-series data from fractures and seepage water near the deposit.

Leukemia and exposure to ionizing radiation among German uranium miners.

PubMed

Möhner, Matthias; Lindtner, Manfred; Otten, Heinz; Gille, Hans-G

2006-04-01

It is well known that uranium miners are at an increased risk of lung cancer. Whether they also have an increased risk for other cancer sites remains under discussion. The aim of this study was to examine the leukemia risk among miners. An individually matched case-control study of former uranium miners in East Germany was conducted with 377 cases and 980 controls. Using conditional logistic regression models, a dose-response relationship between leukemia risk and radon progeny could not be confirmed. Yet, a significantly elevated risk is seen in the category > or = 400 mSv when combining gamma-radiation and long-lived radionuclides. The results suggest that an elevated risk for leukemia is restricted to employees with a very long occupational career in underground uranium mining or uranium processing. Moreover, the study does not support the hypothesis of an association between exposure to short-lived radon progeny and leukemia risk. Copyright 2006 Wiley-Liss, Inc.

1-D/3-D geologic model of the Western Canada Sedimentary Basin

USGS Publications Warehouse

Higley, D.K.; Henry, M.; Roberts, L.N.R.; Steinshouer, D.W.

2005-01-01

The 3-D geologic model of the Western Canada Sedimentary Basin comprises 18 stacked intervals from the base of the Devonian Woodbend Group and age equivalent formations to ground surface; it includes an estimated thickness of eroded sediments based on 1-D burial history reconstructions for 33 wells across the study area. Each interval for the construction of the 3-D model was chosen on the basis of whether it is primarily composed of petroleum system elements of reservoir, hydrocarbon source, seal, overburden, or underburden strata, as well as the quality and areal distribution of well and other data. Preliminary results of the modeling support the following interpretations. Long-distance migration of hydrocarbons east of the Rocky Mountains is indicated by oil and gas accumulations in areas within which source rocks are thermally immature for oil and (or) gas. Petroleum systems in the basin are segmented by the northeast-trending Sweetgrass Arch; hydrocarbons west of the arch were from source rocks lying near or beneath the Rocky Mountains, whereas oil and gas east of the arch were sourced from the Williston Basin. Hydrocarbon generation and migration are primarily due to increased burial associated with the Laramide Orogeny. Hydrocarbon sources and migration were also influenced by the Lower Cretaceous sub-Mannville unconformity. In the Peace River Arch area of northern Alberta, Jurassic and older formations exhibit high-angle truncations against the unconformity. Potential Paleozoic though Mesozoic hydrocarbon source rocks are in contact with overlying Mannville Group reservoir facies. In contrast, in Saskatchewan and southern Alberta the contacts are parallel to sub-parallel, with the result that hydrocarbon source rocks are separated from the Mannville Group by seal-forming strata within the Jurassic. Vertical and lateral movement of hydrocarbons along the faults in the Rocky Mountains deformed belt probably also resulted in mixing of oil and gas from numerous source rocks in Alberta.

Translocation of uranium from water to foodstuff while cooking.

PubMed

Krishnapriya, K C; Baksi, Ananya; Chaudhari, Swathi; Gupta, Soujit Sen; Pradeep, T

2015-10-30

The present work report the unusual uranium uptake by foodstuff, especially those rich in carbohydrates like rice when they are cooked in water, contaminated with uranium. The major staple diet in South Asia, rice, was chosen to study its interaction with UO2(2+), the active uranium species in water, using inductively coupled plasma mass spectrometry. Highest uptake limit was checked by cooking rice at very high uranium concentration and it was found to be good scavenger of uranium. To gain insight into the mechanism of uptake, direct interaction of UO2(2+) with monosaccharides was also studied, using electrospray ionization mass spectrometry taking mannose as a model. The studies have been done with dissolved uranium salt, uranyl nitrate hexahydrate (UO2(NO3)2·6H2O), as well as the leachate of a stable oxide of uranium, UO2(s), both of which exist as UO2(2+) in water. Among the eight different rice varieties investigated, Karnataka Ponni showed the maximum uranium uptake whereas unpolished Basmati rice showed the minimum. Interaction with other foodstuffs (potato, carrot, peas, kidney beans and lentils) with and without NaCl affected the extent of chemical interaction but was not consistent with the carbohydrate content. Uranium interaction with D-mannose monitored through ESI-MS, under optimized instrumental parameters, identified the peaks corresponding to uranyl adduct with mannose monomer, dimer and trimer and the species were confirmed by MS/MS studies. The product ion mass spectra showed peaks illustrating water loss from the parent ion as the collision energy was increased, an evidence for the strong interaction of uranium with mannose. This study would constitute the essential background for understanding interaction of uranium with various foods. Extension of this work would involve identification of foodstuff as green heavy metal scavengers. Copyright © 2015. Published by Elsevier B.V.

Hypertension and hematologic parameters in a community near a uranium processing facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, Sara E., E-mail: swagner@uga.edu; Burch, James B.; South Carolina Statewide Cancer Prevention and Control Program, Columbia, SC

Background: Environmental uranium exposure originating as a byproduct of uranium processing can impact human health. The Fernald Feed Materials Production Center functioned as a uranium processing facility from 1951 to 1989, and potential health effects among residents living near this plant were investigated via the Fernald Medical Monitoring Program (FMMP). Methods: Data from 8216 adult FMMP participants were used to test the hypothesis that elevated uranium exposure was associated with indicators of hypertension or changes in hematologic parameters at entry into the program. A cumulative uranium exposure estimate, developed by FMMP investigators, was used to classify exposure. Systolic and diastolicmore » blood pressure and physician diagnoses were used to assess hypertension; and red blood cells, platelets, and white blood cell differential counts were used to characterize hematology. The relationship between uranium exposure and hypertension or hematologic parameters was evaluated using generalized linear models and quantile regression for continuous outcomes, and logistic regression or ordinal logistic regression for categorical outcomes, after adjustment for potential confounding factors. Results: Of 8216 adult FMMP participants 4187 (51%) had low cumulative uranium exposure, 1273 (15%) had moderate exposure, and 2756 (34%) were in the high (>0.50 Sievert) cumulative lifetime uranium exposure category. Participants with elevated uranium exposure had decreased white blood cell and lymphocyte counts and increased eosinophil counts. Female participants with higher uranium exposures had elevated systolic blood pressure compared to women with lower exposures. However, no exposure-related changes were observed in diastolic blood pressure or hypertension diagnoses among female or male participants. Conclusions: Results from this investigation suggest that residents in the vicinity of the Fernald plant with elevated exposure to uranium primarily via inhalation exhibited decreases in white blood cell counts, and small, though statistically significant, gender-specific alterations in systolic blood pressure at entry into the FMMP.« less

Formation of the Shelf-edge Cretaceous-Tertiary contact off the southeastern U.S. Coast

USGS Publications Warehouse

Poppe, L.J.; Hathaway, J.C.; Hall, R.E.; Commeau, R.F.

1986-01-01

Submarine erosion, associated with changes in position of the proto-Gulf Stream, was the dominant mechanism controlling the formation of the Cretaceous-Tertiary unconformity in AMCOR borehole 6004. Paleontologic evidence indicates that this unconformity, which is marked by a gravelly-sand enriched in glauconitic and phosphoritic concretions, represents a hiatus of about 7 m.y. Both Cretaceous and Paleocene sediments contain middle-outer neritic foraminiferal assemblages that become more diverse with distance from the contact. Of the elemental abundances measured, Al, Ba, Co, Fe, Ga, K, Mg/Ca, Mo, Ni, P, Sr/Ca, V, Y, and Zn show a strong positive correlation with proximity to the contact, probably as a result of the concentration of authigenic and heavy minerals present as lag sediments on the erosion surface. ?? 1986.

Actual and Idealized Crystal Field Parameterizations for the Uranium Ions in UF 4

NASA Astrophysics Data System (ADS)

Gajek, Z.; Mulak, J.; Krupa, J. C.

1993-12-01

The crystal field parameters for the actual coordination symmetries of the uranium ions in UF 4, C2 and C1, and for their idealizations to D2, C2 v , D4, D4 d , and the Archimedean antiprism point symmetries are given. They have been calculated by means of both the perturbative ab initio model and the angular overlap model and are referenced to the recent results fitted by Carnall's group. The equivalency of some different sets of parameters has been verified with the standardization procedure. The adequacy of several idealized approaches has been tested by comparison of the corresponding splitting patterns of the 3H 4 ground state. Our results support the parameterization given by Carnall. Furthermore, the parameterization of the crystal field potential and the splitting diagram for the symmetryless uranium ion U( C1) are given. Having at our disposal the crystal field splittings for the two kinds of uranium ions in UF 4, U( C2) and U( C1), we calculate the model plots of the paramagnetic susceptibility χ( T) and the magnetic entropy associated with the Schottky anomaly Δ S( T) for UF 4.

Model for dolomite formation in northwest Florida

USGS Publications Warehouse

Cooper, C.R.; Tindall, J.A.

1994-01-01

Petrographic methods are used to examine the nature of the Floridan post-Oligocene unconformity and diagenetic responses in the associated carbonate units. The study addresses the depositional environment and the character of sediments associated with the unconformity, types and timing of diagenetic changes, and mode of dolomitization for the Suwannee Limestone dolomites and basal Hawthorn Group dolosilts. The purpose of the study is to determine if the original texture of geologic materials is preserved more frequently in rocks deposited in a supratidal environment in the uppermost Floridan carbonates, to examine possible sources of magnesium for the dolomitization that has occurred in the Floridan aquifer, and to determine the chemical environment of dolomite formation. On the basis of lithology, the tri-county study area can be divided into two regions; one in which the uppermost Floridan carbonate is calcareous or locally silicified, and one in which the aquifer system is capped with dolomite. Lateral interfingering between the two regions is apparent, and it is inferred that the boundary between the limestone and dolomite represents a geochemical boundary between a mixed marine and freshwater environment and a subaerially exposed freshwater environment. Where dolomite has replaced the uppermost Suwannee Limestone, the dolomite is overlain by a thin unit of dolosilt. The predominant source of magnesium for the dolomitization that occurred in the study area is probably seawater. ?? 1994.

Updated Conceptual Model for the 300 Area Uranium Groundwater Plume

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zachara, John M.; Freshley, Mark D.; Last, George V.

2012-11-01

The 300 Area uranium groundwater plume in the 300-FF-5 Operable Unit is residual from past discharge of nuclear fuel fabrication wastes to a number of liquid (and solid) disposal sites. The source zones in the disposal sites were remediated by excavation and backfilled to grade, but sorbed uranium remains in deeper, unexcavated vadose zone sediments. In spite of source term removal, the groundwater plume has shown remarkable persistence, with concentrations exceeding the drinking water standard over an area of approximately 1 km2. The plume resides within a coupled vadose zone, groundwater, river zone system of immense complexity and scale. Interactionsmore » between geologic structure, the hydrologic system driven by the Columbia River, groundwater-river exchange points, and the geochemistry of uranium contribute to persistence of the plume. The U.S. Department of Energy (DOE) recently completed a Remedial Investigation/Feasibility Study (RI/FS) to document characterization of the 300 Area uranium plume and plan for beginning to implement proposed remedial actions. As part of the RI/FS document, a conceptual model was developed that integrates knowledge of the hydrogeologic and geochemical properties of the 300 Area and controlling processes to yield an understanding of how the system behaves and the variables that control it. Recent results from the Hanford Integrated Field Research Challenge site and the Subsurface Biogeochemistry Scientific Focus Area Project funded by the DOE Office of Science were used to update the conceptual model and provide an assessment of key factors controlling plume persistence.« less

Can we predict uranium bioavailability based on soil parameters? Part 1: effect of soil parameters on soil solution uranium concentration.

PubMed

Vandenhove, H; Van Hees, M; Wouters, K; Wannijn, J

2007-01-01

Present study aims to quantify the influence of soil parameters on soil solution uranium concentration for (238)U spiked soils. Eighteen soils collected under pasture were selected such that they covered a wide range for those parameters hypothesised as being potentially important in determining U sorption. Maximum soil solution uranium concentrations were observed at alkaline pH, high inorganic carbon content and low cation exchange capacity, organic matter content, clay content, amorphous Fe and phosphate levels. Except for the significant correlation between the solid-liquid distribution coefficients (K(d), L kg(-1)) and the organic matter content (R(2)=0.70) and amorphous Fe content (R(2)=0.63), there was no single soil parameter significantly explaining the soil solution uranium concentration (which varied 100-fold). Above pH=6, log(K(d)) was linearly related with pH [log(K(d))=-1.18 pH+10.8, R(2)=0.65]. Multiple linear regression analysis did result in improved predictions of the soil solution uranium concentration but the model was complex.

Carbothermic synthesis of 820 μm uranium nitride kernels: Literature review, thermodynamics, analysis, and related experiments

NASA Astrophysics Data System (ADS)

Lindemer, T. B.; Voit, S. L.; Silva, C. M.; Besmann, T. M.; Hunt, R. D.

2014-05-01

The US Department of Energy is developing a new nuclear fuel that would be less susceptible to ruptures during a loss-of-coolant accident. The fuel would consist of tristructural isotropic coated particles with uranium nitride (UN) kernels with diameters near 825 μm. This effort explores factors involved in the conversion of uranium oxide-carbon microspheres into UN kernels. An analysis of previous studies with sufficient experimental details is provided. Thermodynamic calculations were made to predict pressures of carbon monoxide and other relevant gases for several reactions that can be involved in the conversion of uranium oxides and carbides into UN. Uranium oxide-carbon microspheres were heated in a microbalance with an attached mass spectrometer to determine details of calcining and carbothermic conversion in argon, nitrogen, and vacuum. A model was derived from experiments on the vacuum conversion to uranium oxide-carbide kernels. UN-containing kernels were fabricated using this vacuum conversion as part of the overall process. Carbonitride kernels of ∼89% of theoretical density were produced along with several observations concerning the different stages of the process.

An atomic model for neutral and singly ionized uranium

NASA Technical Reports Server (NTRS)

Maceda, E. L.; Miley, G. H.

1979-01-01

A model for the atomic levels above ground state in neutral, U(0), and singly ionized, U(+), uranium is described based on identified atomic transitions. Some 168 states in U(0) and 95 in U(+) are found. A total of 1581 atomic transitions are used to complete this process. Also discussed are the atomic inverse lifetimes and line widths for the radiative transitions as well as the electron collisional cross sections.

Application of the DART Code for the Assessment of Advanced Fuel Behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rest, J.; Totev, T.

2007-07-01

The Dispersion Analysis Research Tool (DART) code is a dispersion fuel analysis code that contains mechanistically-based fuel and reaction-product swelling models, a one dimensional heat transfer analysis, and mechanical deformation models. DART has been used to simulate the irradiation behavior of uranium oxide, uranium silicide, and uranium molybdenum aluminum dispersion fuels, as well as their monolithic counterparts. The thermal-mechanical DART code has been validated against RERTR tests performed in the ATR for irradiation data on interaction thickness, fuel, matrix, and reaction product volume fractions, and plate thickness changes. The DART fission gas behavior model has been validated against UO{sub 2}more » fission gas release data as well as measured fission gas-bubble size distributions. Here DART is utilized to analyze various aspects of the observed bubble growth in U-Mo/Al interaction product. (authors)« less

Effects of uranium mining, Puerco River, New Mexico

USGS Publications Warehouse

Lopes, Thomas J.

1991-01-01

Effluent from uranium-mine dewatering and acidic water released by a tailings-pond dike failure increased radionuclide activities in streamflow in the Puerco River in New Mexico and Arizona. Median dissolved gross-alpha activity in the streamflow was 1,130 picocuries per liter from 1975 to 1986 when mine discharges ceased and 6.2 picocuries per liter from 1986 to 1989. From 1975 to July 1979, major ions in streamflow at the Puerco River at Gallup streamflow-gaging station were sodium, bicarbonate, and sulfate. On July 16, 1979, the day of the tailing spill, major ions in streamflow were magnesium, calcium, and sulfate. From 1979 to 1984, major ions in streamflow had a greater proportion of calcium and sulfate than prior to the spill, indicating flushing of residual tailings solution. Geochemical modeling of mine effluent indicates that uranium was unlikely to precipitate from effluent between the mines and Gallup or when mixed with wastewater downstream from Gallup. Geochemical modeling of acidic-tailings solution indicates that uranium was in solution as far downstream as Gallup. When the acidic-tailings solution mixed with 10- to 40-percent wastewater, uranium may have precipitated from solution as carnotite [K2(UO2)2(VO4)2] and tyuyamunite [Ca(UO2)2(VO4)2].

Sandstone type uranium deposits in the Ordos Basin, Northwest China: A case study and an overview

NASA Astrophysics Data System (ADS)

Akhtar, Shamim; Yang, Xiaoyong; Pirajno, Franco

2017-09-01

This paper provides a comprehensive review on studies of sandstone type uranium deposits in the Ordos Basin, Northwest China. As the second largest sedimentary basin, the Ordos Basin has great potential for targeting sandstone type U mineralization. The newly found and explored Dongsheng and Diantou sandstone type uranium deposits are hosted in the Middle Jurassic Zhilou Formation. A large number of investigations have been conducted to trace the source rock compositions and relationship between lithic subarkose sandstone host rock and uranium mineralization. An optical microscopy study reveals two types of alteration associated with the U mineralization: chloritization and sericitization. Some unusual mineral structures, with compositional similarity to coffinite, have been identified in a secondary pyrite by SEM These mineral phases are proposed to be of bacterial origin, following high resolution mapping of uranium minerals and trace element determinations in situ. Moreover, geochemical studies of REE and trace elements constrained the mechanism of uranium enrichment, displaying LREE enrichment relative to HREE. Trace elements such as Pb, Mo and Ba have a direct relationship with uranium enrichment and can be used as index for mineralization. The source of uranium ore forming fluids and related geological processes have been studied using H, O and C isotope systematics of fluid inclusions in quartz veins and the calcite cement of sandstone rocks hosting U mineralization. Both H and O isotopic compositions of fluid inclusions reveal that ore forming fluids are a mixture of meteoric water and magmatic water. The C and S isotopes of the cementing material of sandstone suggest organic origin and bacterial sulfate reduction (BSR), providing an important clue for U mineralization. Discussion of the ore genesis shows that the greenish gray sandstone plays a crucial role during processes leading to uranium mineralization. Consequently, an oxidation-reduction model for sandstone-type uranium deposit is proposed, which can elucidate the source of uranium in the deposits of the Ordos Basin, based on the role of organic materials and sulfate reducing bacteria. We discuss the mechanism of uranium deposition responsible for the genesis of these large sandstone type uranium deposits in this unique sedimentary basin.

Health Risk Assessment of Embedded Depleted Uranium: Behavior, Physiology, Histology and Biokenetic Modeling

DTIC Science & Technology

1997-10-01

mg/in) (or in dogs or monkeys exposed for 5 years). Yet uranium concentrations in the kidney were as high as 1.1 tg U/g kidney wet weight in the rat...8.3 in the dog and 17.0 in the monkey), levels reported to cause acute renal toxicity (e.g., 2). Thus the chronic effects of uranium exposure remain...Anesthesia is induced with ketamine hydrochloride (80 mg/kg) in combination with xylazine hydrochloride (4 mg/kg), given i.p. Fragments are implanted within

Pena blanca natural analogue project: summary of activities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levy, Schon S; Goldstein, Steven J; Abdel - Fattah, Amr I

2010-12-08

The inactive Nopal I uranium mine in silicic tuff north of Chihuahua City, Chihuahua, Mexico, was studied as a natural analogue for an underground nuclear-waste repository in the unsaturated zone. Site stratigraphy was confirmed from new drill core. Datafrom site studies include chemical and isotopic compositions of saturated- and unsaturated-zone waters. A partial geochronology of uranium enrichment and mineralization was established. Evidence pertinent to uranium-series transport in the soil zone and changing redox conditions was collected. The investigations contributed to preliminary, scoping-level performance assessment modeling.

The subsurface geology of the Florida-Hatteras shelf, slope, and inner Blake Plateau

USGS Publications Warehouse

Paull, Charles K.; Dillon, William P.

1979-01-01

The structure and stratigraphy of the Florida-Hatteras Slope and inner Blake Plateau was studied by means of 4,780 km of single-channel air gun seismic reflection profiles. Control for the seismic stratigraphy is provided by correlating reflecting units and paleontologically dated stratigraphic units identified in offshore wells and dredge hauls. Many Tertiary unconformities exist, and major regional unconformities at the end of the Oligocene and in the late Paleocene are mapped. Reflecting surfaces believed to represent the tops of the Cretaceous, Paleocene, and Oligocene extend throughout the region. Upper Cretaceous (pre-Maastrichtian) rocks on the southeastern side of the Carolina Platform form a large seaward-facing progradational wedge. The Upper Cretaceous rocks in the Southeast Georgia Embayment, are seismically transparent and on the inner Blake Plateau are cut by numerous small faults, perhaps due to compaction. Within the survey area relatively flat-lying Maastrichtian and Paleocene strata show no evidence that a feature similar to the present Florida-Hatteras Slope existed at the beginning of the Tertiary. Late Paleocene erosion, related to the initiation of the Gulf Stream flow, probably developed this regional unconformity. Eocene and Oligocene sediments landward of the present Gulf Stream form a thick sequence of seaward-dipping progradational beds. A seaward progradational wedge of Miocene to Holocene age covers a regionally traceable unconformity, which separates the Oligocene from the Miocene sediments. Under and seaward of the present Gulf Stream, the Eocene and younger sediment supply was much smaller and the buildup is comparatively insignificant. The difference in accumulation rates in the Eocene and younger sediments, landward and seaward of the Gulf Stream, is responsible for the Florida-Hatteras Slope. Tertiary isopach maps suggest that there is a well developed triangular depocenter under the shelf. The edges of the depocenter correspond with magnetic anomalies and it is suggested that the depocenter is related to differential subsidence during the Tertiary across older crustal structures. The Eocene and Oligocene units contain the aquifer onshore, and the aquifer probably remains in these units offshore. With this assumption the potential aquifer has been identified and traced under the shelf and slope.

DART model for irradiation-induced swelling of uranium silicide dispersion fuel elements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rest, J.; Hofman, G.L.

1999-04-01

Models for the interaction of uranium silicide dispersion fuels with an aluminum matrix, for the resultant reaction product swelling, and for the calculation of the stress gradient within the fuel particles are described within the context of DART fission-gas-induced swelling models. The effects of an aluminide shell on fuel particle swelling are evaluated. Validation of the model is demonstrated by comparing DART calculations with irradiation data for the swelling of U{sub 3}SiAl-Al and U{sub 3}Si{sub 2}-Al in variously designed dispersion fuel elements.

Modeling non-steady state radioisotope transport in the vadose zone--A case study using uranium isotopes at Pena Blanca, Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ku, T. L.; Luo, S.; Goldstein, S. J.

2009-06-01

Current models using U- and Th-series disequilibria to study radioisotope transport in groundwater systems mostly consider a steady-state situation. These models have limited applicability to the vadose zone (UZ) where the concentration and migratory behavior of radioisotopes in fluid are often transitory. We present here, as a first attempt of its kind, a model simulating the non-steady state, intermittent fluid transport in vadose layers. It provides quantitative constraints on in-situ migration of dissolved and colloidal radioisotopes in terms of retardation factor and rock-water interaction (or water transit) time. For uranium, the simulation predicts that intermittent flushing in the UZ leadsmore » to a linear relationship between reciprocal U concentration and {sup 234}U/{sup 238}U ratio in percolating waters, with the intercept and slope bearing information on the rates of dissolution and {alpha}-recoil of U isotopes, respectively. The general validity of the model appears to be borne out by the measurement of uranium isotopes in UZ waters collected at various times over a period during 1995-2006 from a site in the Pena Blanca mining district, Mexico, where the Nopal I uranium deposit is located. Enhanced {sup 234}U/{sup 238}U ratios in vadose-zone waters resulting from lengthened non-flushing time as prescribed by the model provide an interpretative basis for using {sup 234}U/{sup 238}U in cave calcites to reconstruct the regional changes in hydrology and climate. We also provide a theoretical account of the model's potential applications using radium isotopes.« less

Modeling non-steady state radioisotope transport in the vadose zone - A case study using uranium isotopes at Peña Blanca, Mexico

NASA Astrophysics Data System (ADS)

Ku, T. L.; Luo, S.; Goldstein, S. J.; Murrell, M. T.; Chu, W. L.; Dobson, P. F.

2009-10-01

Current models using U- and Th-series disequilibria to study radioisotope transport in groundwater systems mostly consider a steady-state situation. These models have limited applicability to the vadose zone (UZ) where the concentration and migratory behavior of radioisotopes in fluid are often transitory. We present here, as a first attempt of its kind, a model simulating the non-steady state, intermittent fluid transport in vadose layers. It provides quantitative constraints on in-situ migration of dissolved and colloidal radioisotopes in terms of retardation factor and rock-water interaction (or water transit) time. For uranium, the simulation predicts that intermittent flushing in the UZ leads to a linear relationship between reciprocal U concentration and 234U/ 238U ratio in percolating waters, with the intercept and slope bearing information on the rates of dissolution and α-recoil of U isotopes, respectively. The general validity of the model appears to be borne out by the measurement of uranium isotopes in UZ waters collected at various times over a period during 1995-2006 from a site in the Peña Blanca mining district, Mexico, where the Nopal I uranium deposit is located. Enhanced 234U/ 238U ratios in vadose-zone waters resulting from lengthened non-flushing time as prescribed by the model provide an interpretative basis for using 234U/ 238U in cave calcites to reconstruct the regional changes in hydrology and climate. We also provide a theoretical account of the model's potential applications using radium isotopes.

The separation of uranium ions by natural and modified diatomite from aqueous solution.

PubMed

Sprynskyy, Myroslav; Kovalchuk, Iryna; Buszewski, Bogusław

2010-09-15

In this work the natural and the surfactant modified diatomite has been tested for ability to remove uranium ions from aqueous solutions. Such controlling factors of the adsorption process as initial uranium concentration, pH, contact time and ionic strength have been investigated. Effect of ionic strength of solution has been examined using the solutions of NaCl, Na(2)CO(3) and K(2)SO(4). The pseudo-first order and the pseudo-second order models have been used to analyze the adsorption kinetic results, whereas the Langmuir and the Freundlich isotherms have been used to the equilibrium adsorption data. The effects of the adsorbent modification as well as uranium adsorption on the diatomite surface have been studied using X-ray powder diffraction, scanning electron microscopy and FTIR spectroscopy. The maximum adsorption capacities of the natural and the modified diatomite towards uranium were 25.63 micromol/g and 667.40 micromol/g, respectively. The desorptive solutions of HCl, NaOH, Na(2)CO(3), K(2)SO(4), CaCO(3), humic acid, cool and hot water have been tested to recover uranium from the adsorbent. The highest values of uranium desorption (86%) have been reached using 0.1M HCl. Copyright 2010 Elsevier B.V. All rights reserved.

Bioaccumulation characterization of uranium by a novel Streptomyces sporoverrucosus dwc-3.

PubMed

Li, Xiaolong; Ding, Congcong; Liao, Jiali; Du, Liang; Sun, Qun; Yang, Jijun; Yang, Yuanyou; Zhang, Dong; Tang, Jun; Liu, Ning

2016-03-01

The biosorption mechanisms of uranium on an aerobic bacterial strain Streptomyces sporoverrucosus dwc-3, isolated from a potential disposal site for (ultra-)low uraniferous radioactive waste in Southwest China, were evaluated by using transmission electron microscopy (TEM), energy dispersive X-ray (EDX) analysis, Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), proton induced X-ray emission (PIXE) and enhanced proton backscattering spectrometry (EPBS). Approximately 60% of total uranium at an initial concentration of 10mg/L uranium nitrate solution could be absorbed on 100mg S. sporoverrucosus dwc-3 with an adsorption capacity of more than 3.0mg/g (wet weight) after 12hr at room temperature at pH3.0. The dynamic biosorption process of S. sporoverrucosus dwc-3 for uranyl ions was well described by a pseudo second-order model. S. sporoverrucosus dwc-3 could accumulate uranium on cell walls and within the cell, as revealed by SEM and TEM analysis as well as EDX spectra. XPS and FT-IR analysis further suggested that the absorbed uranium was bound to amino, phosphate and carboxyl groups of the cells. Additionally, PIXE and EPBS results confirmed that ion exchange also contributed to the adsorption process of uranium. Copyright © 2015. Published by Elsevier B.V.

Highly Enriched Uranium Metal Cylinders Surrounded by Various Reflector Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernard Jones; J. Blair Briggs; Leland Monteirth

A series of experiments was performed at Los Alamos Scientific Laboratory in 1958 to determine critical masses of cylinders of Oralloy (Oy) reflected by a number of materials. The experiments were all performed on the Comet Universal Critical Assembly Machine, and consisted of discs of highly enriched uranium (93.3 wt.% 235U) reflected by half-inch and one-inch-thick cylindrical shells of various reflector materials. The experiments were performed by members of Group N-2, particularly K. W. Gallup, G. E. Hansen, H. C. Paxton, and R. H. White. This experiment was intended to ascertain critical masses for criticality safety purposes, as well asmore » to compare neutron transport cross sections to those obtained from danger coefficient measurements with the Topsy Oralloy-Tuballoy reflected and Godiva unreflected critical assemblies. The reflector materials examined in this series of experiments are as follows: magnesium, titanium, aluminum, graphite, mild steel, nickel, copper, cobalt, molybdenum, natural uranium, tungsten, beryllium, aluminum oxide, molybdenum carbide, and polythene (polyethylene). Also included are two special configurations of composite beryllium and iron reflectors. Analyses were performed in which uncertainty associated with six different parameters was evaluated; namely, extrapolation to the uranium critical mass, uranium density, 235U enrichment, reflector density, reflector thickness, and reflector impurities. In addition to the idealizations made by the experimenters (removal of the platen and diaphragm), two simplifications were also made to the benchmark models that resulted in a small bias and additional uncertainty. First of all, since impurities in core and reflector materials are only estimated, they are not included in the benchmark models. Secondly, the room, support structure, and other possible surrounding equipment were not included in the model. Bias values that result from these two simplifications were determined and associated uncertainty in the bias values were included in the overall uncertainty in benchmark keff values. Bias values were very small, ranging from 0.0004 ?k low to 0.0007 ?k low. Overall uncertainties range from ? 0.0018 to ? 0.0030. Major contributors to the overall uncertainty include uncertainty in the extrapolation to the uranium critical mass and the uranium density. Results are summarized in Figure 1. Figure 1. Experimental, Benchmark-Model, and MCNP/KENO Calculated Results The 32 configurations described and evaluated under ICSBEP Identifier HEU-MET-FAST-084 are judged to be acceptable for use as criticality safety benchmark experiments and should be valuable integral benchmarks for nuclear data testing of the various reflector materials. Details of the benchmark models, uncertainty analyses, and final results are given in this paper.« less

Quantifying uranium transport rates and storage of fluvially eroded mine tailings from a historic mine site in the Grand Canyon Region

NASA Astrophysics Data System (ADS)

Skalak, K.; Benthem, A. J.; Walton-Day, K. E.; Jolly, G.

2015-12-01

The Grand Canyon region contains a large number of breccia pipes with economically viable uranium, copper, and silver concentrations. Mining in this region has occurred since the late 19th century and has produced ore and waste rock having elevated levels of uranium and other contaminants. Fluvial transport of these contaminants from mine sites is a possibility, as this arid region is susceptible to violent storms and flash flooding which might erode and mobilize ore or waste rock. In order to assess and manage the risks associated with uranium mining, it is important to understand the transport and storage rates of sediment and uranium within the ephemeral streams of this region. We are developing a 1-dimensional sediment transportation model to examine uranium transport and storage through a typical canyon system in this region. Our study site is Hack Canyon Mine, a uranium and copper mine site, which operated in the 1980's and is currently experiencing fluvial erosion of its waste rock repository. The mine is located approximately 40km upstream from the Colorado River and is in a deep, narrow canyon with a small watershed. The stream is ephemeral for the upper half of its length and sediment is primarily mobilized during flash flood events. We collected sediment samples at 110 locations longitudinally through the river system to examine the distribution of uranium in the stream. Samples were sieved to the sand size and below fraction (<2mm) and uranium was measured by gamma-ray spectroscopy. Sediment storage zones were also examined in the upper 8km of the system to determine where uranium is preferentially stored in canyon systems. This information will quantify the downstream transport of constituents associated with the Hack Canyon waste rock and contribute to understanding the risks associated with fluvial mobilization of uranium mine waste.

Model-based Analysis of Mixed Uranium(VI) Reduction by Biotic and Abiotic Pathways During in Situ Bioremediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Jiao; Scheibe, Timothy D.; Mahadevan, Radhakrishnan

2013-10-24

Uranium bioremediation has emerged as a potential strategy of cleanup of radionuclear contamination worldwide. An integrated geochemical & microbial community model is a promising approach to predict and provide insights into the bioremediation of a complicated natural subsurface. In this study, an integrated column-scale model of uranium bioremediation was developed, taking into account long-term interactions between biotic and abiotic processes. It is also combined with a comprehensive thermodynamic analysis to track the fate and cycling of biogenic species. As compared with other bioremediation models, the model increases the resolution of the connection of microbial community to geochemistry and establishes directmore » quantitative correlation between overall community evolution and geochemical variation, thereby accurately predicting the community dynamics under different sedimentary conditions. The thermodynamic analysis examined a recently identified homogeneous reduction of U(VI) by Fe(II) under dynamic sedimentary conditions across time and space. It shows that the biogenic Fe(II) from Geobacter metabolism can be removed rapidly by the biogenic sulphide from sulfate reducer metabolism, hence constituting one of the reasons that make the abiotic U(VI) reduction thermodynamically infeasible in the subsurface. Further analysis indicates that much higher influent concentrations of both Fe(II) and U(VI) than normal are required to for abiotic U(VI) reduction to be thermodynamically feasible, suggesting that the abiotic reduction cannot be an alternative to the biotic reduction in the remediation of uranium contaminated groundwater.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lombardo, N.J.; Marseille, T.J.; White, M.D.

TRUMP-BD (Boil Down) is an extension of the TRUMP (Edwards 1972) computer program for the analysis of nuclear fuel assemblies under severe accident conditions. This extension allows prediction of the heat transfer rates, metal-water oxidation rates, fission product release rates, steam generation and consumption rates, and temperature distributions for nuclear fuel assemblies under core uncovery conditions. The heat transfer processes include conduction in solid structures, convection across fluid-solid boundaries, and radiation between interacting surfaces. Metal-water reaction kinetics are modeled with empirical relationships to predict the oxidation rates of steam-exposed Zircaloy and uranium metal. The metal-water oxidation models are parabolic inmore » form with an Arrhenius temperature dependence. Uranium oxidation begins when fuel cladding failure occurs; Zircaloy oxidation occurs continuously at temperatures above 13000{degree}F when metal and steam are available. From the metal-water reactions, the hydrogen generation rate, total hydrogen release, and temporal and spatial distribution of oxide formations are computed. Consumption of steam from the oxidation reactions and the effect of hydrogen on the coolant properties is modeled for independent coolant flow channels. Fission product release from exposed uranium metal Zircaloy-clad fuel is modeled using empirical time and temperature relationships that consider the release to be subject to oxidation and volitization/diffusion ( bake-out'') release mechanisms. Release of the volatile species of iodine (I), tellurium (Te), cesium (Ce), ruthenium (Ru), strontium (Sr), zirconium (Zr), cerium (Cr), and barium (Ba) from uranium metal fuel may be modeled.« less

Structural and Depositional Evolution of the Stevenson Basin, a Gulf of Alaska Forearc Basin: Insights from Legacy Seismic and Borehole Data

NASA Astrophysics Data System (ADS)

Bhattacharya, R.; Liberty, L. M.; Almeida, R. V.; Hubbard, J.

2016-12-01

We explore the structural and depositional evolution of the Stevenson Basin, Gulf of Alaska from a dense network of 2-D marine seismic profiles that span the Gulf of Alaska continental margin. The grid of 71 seismic profiles was acquired as part of a 1975 Mineral Management Services (MMS) exploration project to assess basin architecture along the Alaska continental shelf. We obtained unmigrated and stacked seismic profiles in TIFF format. We converted the data to SEGY format and migrated each profile. Within the Stevenson Basin, we identify key seismic horizons, including the regional Eocene-Miocene unconformity, that provide insights into its depositional and structural history. Using these observations combined with stacking velocities, sonic logs from wells, and refraction velocities from the Edge profile of Ye et al. (1997), we develop a local 3D velocity model that we use to depth-convert the seismic reflection profiles. By using ties to >2.5 km deep exploration wells, we note the Stevenson Basin is one of many Eocene and younger depocenters that span the forearc between Kodiak and Prince William Sound. Well logs and seismic data suggest basal strata consist of Eocene sediments than are unconformably overlain by Neogene and younger strata. Faults that breach the sea floor suggest active deformation within and at the bounds of this basin, including on new faults that do not follow any pre-existing structural trends. This assessment is consistent with slip models that place tsunamigenic faults that ruptured during the 1964 Great Alaska earthquake in the vicinity of the basin. The catalog of faults, their slip history and the depositional evolution of the Stevenson Basin, all suggest that the basin evolution may be controlled by heterogeneities along the incoming plate.

Mineral solubility and free energy controls on microbial reaction kinetics: Application to contaminant transport in the subsurface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taillefert, Martial; Van Cappellen, Philippe

Recent developments in the theoretical treatment of geomicrobial reaction processes have resulted in the formulation of kinetic models that directly link the rates of microbial respiration and growth to the corresponding thermodynamic driving forces. The overall objective of this project was to verify and calibrate these kinetic models for the microbial reduction of uranium(VI) in geochemical conditions that mimic as much as possible field conditions. The approach combined modeling of bacterial processes using new bioenergetic rate laws, laboratory experiments to determine the bioavailability of uranium during uranium bioreduction, evaluation of microbial growth yield under energy-limited conditions using bioreactor experiments, competitionmore » experiments between metabolic processes in environmentally relevant conditions, and model applications at the field scale. The new kinetic descriptions of microbial U(VI) and Fe(III) reduction should replace those currently used in reactive transport models that couple catabolic energy generation and growth of microbial populations to the rates of biogeochemical redox processes. The above work was carried out in collaboration between the groups of Taillefert (batch reactor experiments and reaction modeling) at Georgia Tech and Van Cappellen (retentostat experiments and reactive transport modeling) at University of Waterloo (Canada).« less

Geothermal constraints on Emeishan mantle plume magmatism: paleotemperature reconstruction of the Sichuan Basin, SW China

NASA Astrophysics Data System (ADS)

Zhu, Chuanqing; Hu, Shengbiao; Qiu, Nansheng; Jiang, Qiang; Rao, Song; Liu, Shuai

2018-01-01

The Middle-Late Permian Emeishan Large Igneous Province (ELIP) in southwestern China represents a classic example of a mantle plume origin. To constrain the thermal regime of the ELIP and contemporaneous magmatic activity in the northeastern Sichuan Basin, maximum paleotemperature profiles of deep boreholes were reconstructed using vitrinite reflectance (Ro) and apatite fission track data. Two heating patterns were identified: (1) heating of the overlying lithosphere by magma storage regions and/or magmatic activity related to the mantle plume, which resulted in a relatively strong geothermal field and (2) direct heating of country rock by stock or basalt. Borehole Ro data and reconstructed maximum paleotemperature profiles near the ELIP exhibit abrupt tectonothermal unconformities between the Middle and Late Permian. The profiles in the lower subsections (i.e., pre-Middle Permian) exhibited significantly higher gradients than those in the upper subsections. Distal to the basalt province, high paleo-geotemperatures (hereafter, paleotemperatures) were inferred, despite deformation of the paleogeothermal curve due to deep faults and igneous rocks within the boreholes. In contrast, Ro profiles from boreholes without igneous rocks (i.e., Late Permian) contained no break at the unconformity. Paleotemperature gradients of the upper and the lower subsections and erosion at the Middle/Late Permian unconformity revealed variations in the thermal regime. The inferred spatial distribution of the paleothermal regime and the erosion magnitudes record the magmatic and tectonic-thermal response to the Emeishan mantle plume.

Carbonate mound development in contrasting settings on the Irish margin

NASA Astrophysics Data System (ADS)

van der Land, Cees; Eisele, Markus; Mienis, Furu; de Haas, Henk; Hebbeln, Dierk; Reijmer, John J. G.; van Weering, Tjeerd C. E.

2014-01-01

Cold-water coral carbonate mounds, formed by framework building cold-water corals, are found in several mound provinces on the Irish margin. Differences in cold-water coral mound development rates and sediment composition between mounds at the southwest Rockall Trough margin and the Galway Mound in the Porcupine Seabight are investigated. Variations in sediment composition in the two mound provinces are related to the local environmental conditions and sediment sources. Mound accumulation rates are possibly higher at the Galway Mound probably due to a higher influx of hemipelagic fine grained non-carbonate sediments. In both cold-water coral mound areas, mound growth has been continuous for the last ca 11,000 years, before this period several hiatuses and unconformities exist in the mound record. The most recent unconformity can be correlated across multiple mounds and mound provinces at the Irish margin on the basis of apparent age. On the southwest Rockall Trough margin these hiatuses/unconformities are associated with post-depositional aragonite dissolution in, and lithification of, certain intervals, while at Galway Mound no lithification occurs. This study revealed that the influx and types of material transported to cold-water coral mounds may have a direct impact on the carbonate mound accumulation rate and on post-depositional processes. Significantly, the Logachev Mounds on the SW Rockall Trough margin accumulate slower but, because they contain lithified layers, are less susceptible to erosion. This net effect may account for their larger size compared to the Belgica Mounds.

Dosimetric calculations for uranium miners for epidemiological studies.

PubMed

Marsh, J W; Blanchardon, E; Gregoratto, D; Hofmann, W; Karcher, K; Nosske, D; Tomásek, L

2012-05-01

Epidemiological studies on uranium miners are being carried out to quantify the risk of cancer based on organ dose calculations. Mathematical models have been applied to calculate the annual absorbed doses to regions of the lung, red bone marrow, liver, kidney and stomach for each individual miner arising from exposure to radon gas, radon progeny and long-lived radionuclides (LLR) present in the uranium ore dust and to external gamma radiation. The methodology and dosimetric models used to calculate these organ doses are described and the resulting doses for unit exposure to each source (radon gas, radon progeny and LLR) are presented. The results of dosimetric calculations for a typical German miner are also given. For this miner, the absorbed dose to the central regions of the lung is dominated by the dose arising from exposure to radon progeny, whereas the absorbed dose to the red bone marrow is dominated by the external gamma dose. The uncertainties in the absorbed dose to regions of the lung arising from unit exposure to radon progeny are also discussed. These dose estimates are being used in epidemiological studies of cancer in uranium miners.

Screening level model for ecological risk assessment at EF-Site Los Alamos National Laboratory, New Mexico. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alldredge, A.W.; Kirchner, T.B.; McLendon, T.

1995-12-01

In response to a paucity of data on the chemical toxicity of uranium to plants, a factorial experiment employing five uranium concentrations (0, 50, 500, 5000, 25000 ppm) and three moisture regimes (low, medium, high) was performed using three native grasses. Buchloe dactyloides (buffalograss-mid/late seral), Schizachyrium scoparium (little bluestem-late seral), and Aristida longiseta (purple threeawn-early/mid seral) were grown in monocultures and every mixture of two species under all combinations of uranium and moisture levels. This design allows for the analysis of uranium effects, as well as possible compound effects due to moisture stress. Several measures of plant health and viabilitymore » were made, including: percent emergence, survivability of seedlings and mature plants, root and shoot biomass, and the number and mass of inflorescences. No significant differences between uranium levels were observed in terms of emergence and seedling survival. Effects are evident for plant biomass, fecundity, and long-term survivability.« less

VISION User Guide - VISION (Verifiable Fuel Cycle Simulation) Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacob J. Jacobson; Robert F. Jeffers; Gretchen E. Matthern

2009-08-01

The purpose of this document is to provide a guide for using the current version of the Verifiable Fuel Cycle Simulation (VISION) model. This is a complex model with many parameters; the user is strongly encouraged to read this user guide before attempting to run the model. This model is an R&D work in progress and may contain errors and omissions. It is based upon numerous assumptions. This model is intended to assist in evaluating “what if” scenarios and in comparing fuel, reactor, and fuel processing alternatives at a systems level for U.S. nuclear power. The model is not intendedmore » as a tool for process flow and design modeling of specific facilities nor for tracking individual units of fuel or other material through the system. The model is intended to examine the interactions among the components of a fuel system as a function of time varying system parameters; this model represents a dynamic rather than steady-state approximation of the nuclear fuel system. VISION models the nuclear cycle at the system level, not individual facilities, e.g., “reactor types” not individual reactors and “separation types” not individual separation plants. Natural uranium can be enriched, which produces enriched uranium, which goes into fuel fabrication, and depleted uranium (DU), which goes into storage. Fuel is transformed (transmuted) in reactors and then goes into a storage buffer. Used fuel can be pulled from storage into either separation of disposal. If sent to separations, fuel is transformed (partitioned) into fuel products, recovered uranium, and various categories of waste. Recycled material is stored until used by its assigned reactor type. Note that recovered uranium is itself often partitioned: some RU flows with recycled transuranic elements, some flows with wastes, and the rest is designated RU. RU comes out of storage if needed to correct the U/TRU ratio in new recycled fuel. Neither RU nor DU are designated as wastes. VISION is comprised of several Microsoft Excel input files, a Powersim Studio core, and several Microsoft Excel output files. All must be co-located in the same folder on a PC to function. We use Microsoft Excel 2003 and have not tested VISION with Microsoft Excel 2007. The VISION team uses both Powersim Studio 2005 and 2009 and it should work with either.« less

Biogeochemical controls of uranium bioavailability from the dissolved phase in natural freshwaters

USGS Publications Warehouse

Croteau, Marie-Noele; Fuller, Christopher C.; Cain, Daniel J.; Campbell, Kate M.; Aiken, George R.

2016-01-01

To gain insights into the risks associated with uranium (U) mining and processing, we investigated the biogeochemical controls of U bioavailability in the model freshwater speciesLymnaea stagnalis (Gastropoda). Bioavailability of dissolved U(VI) was characterized in controlled laboratory experiments over a range of water hardness, pH, and in the presence of complexing ligands in the form of dissolved natural organic matter (DOM). Results show that dissolved U is bioavailable under all the geochemical conditions tested. Uranium uptake rates follow first order kinetics over a range encompassing most environmental concentrations. Uranium uptake rates in L. stagnalis ultimately demonstrate saturation uptake kinetics when exposure concentrations exceed 100 nM, suggesting uptake via a finite number of carriers or ion channels. The lack of a relationship between U uptake rate constants and Ca uptake rates suggest that U does not exclusively use Ca membrane transporters. In general, U bioavailability decreases with increasing pH, increasing Ca and Mg concentrations, and when DOM is present. Competing ions did not affect U uptake rates. Speciation modeling that includes formation constants for U ternary complexes reveals that the aqueous concentration of dicarbonato U species (UO2(CO3)2–2) best predicts U bioavailability to L. stagnalis, challenging the free-ion activity model postulate.

Predicting Selectivity of Uranium vs. Vanadium from First Principles: Complete Molecular Design and Adsorption Modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ivanov, Aleksandr; Das, Sadananda; Bryantsev, Vyacheslav

SUMMARYBackground: Uranium is used as the basic fuel for nuclear power plants, which generate significant amounts of electricity and have life cycle carbon emissions that are as low as renewable energy sources. The extraction of this valuable energy commodity from the ground remains controversial, however, mainly because of environmental and health impacts. Alternatively, seawater offers an enormous uranium resource that may be tapped at minimal environmental cost. Currently, amidoxime polymers are the most widely considered adsorbent materials for large-scale extraction of uranium from seawater, but they are not perfectly selective for uranyl, UO22+. In particular, the competition between UO22+ andmore » vanadium (VO2+/VO2+) cations poses a significant challenge to the efficient mining of UO22+. Thus, accelerating progress in the discovery and deployment of advanced materials for the recovery of uranium relies on the design of new ligands with high binding affinity and selectivity for uranium over competing metal ions. A cost-effective route to aid the discovery of new ligands is to apply computational methods to rapidly test attractive candidates and elucidate data-driven guidelines for rational design.Objectives: One of the key components in achieving rational design of highly selective ligands is the establishment of computational tools capable of assessing ligand selectivity trends. Therefore, the objectives of this study include:1.Establish first-principles methods, based on computational chemistry techniques, to calculate stability constants for UO22+ and VO2+/VO2+ complexes.2.Develop computational protocols to assess the binding strengths and selectivity of ligands that can be present in the actual poly(acrylamidoxime) adsorbents.3.Develop adsorption models that can use information from first-principles computational methods to predict the adsorption behavior of uranium and vanadium by adsorbents synthesized at ORNL and compare results with experimental data.Results: In the first part of the study, we present an approach based on quantum chemical calculations that achieves high accuracy in reproducing experimental aqueous stability constants for UO22+ and VO2+/VO2+ complexes, providing the essential foundation for prospective screening of existing or even yet unsynthesized ligands with higher selectivity for uranium over vanadium. The developed computational protocols were used to assess the binding strengths and selectivity of aliphatic dicarboxylate ligands that can be present in the actual poly(acrylamidoxime) adsorbents. It was found that simple dicarboxylic functional groups possess low binding affinity and selectivity for uranyl, because their backbones present architectures that are poorly organized for the UO22+ complexation. In the second part of the study, adsorption models were developed and coupled with the results of the molecular studies in an effort to predict the adsorption of uranium and vanadium by the ORNL AF1 fiber adsorbent. These models can account for the effects of ligand surface density, specific surface area, surface charging, and other non-idealities of the adsorbent surface. It was found that by utilizing the reaction schemes and binding strengths proposed by the molecular studies, the adsorption model could accurately predict the uptake of uranium by both the acyclic amidoxime (AO) and cyclic imide dioximate (IDO) ligand in the ORNL laboratory studies, especially in the more neutral pH ranges (pH 5 to 9). The model, however, performed less adequately for predicting the uptake of vanadium for the same adsorbent. By exploring the causes behind the discrepancy between the adsorption model and the ORNL laboratory data, we found that the effect of surface charging was suppressing the total vanadium uptake predicted by the model. An investigation of literature revealed that the crystal structures of the 1:2 vanadium/IDO complex involved a sodium ion (Na+), which neutralized the charge of the adsorbed species. When this charge neutral species was included in the adsorption model, the predictions of the vanadium capacities were significantly improved across all pH ranges. This result suggests that, during adsorption, some surface species may closely associate with, or adsorb, counter-ions from solution to neutralize the charge of the adsorbent surface.Significance: This study is particularly significant when considering whether to produce an otherwise highly attractive ligand that may be synthetically challenging. If such a ligand is predicted by our calculations to achieve the desired uranium vs vanadium selectivity, this substantially reduces the risk of taking on such synthetic challenges. Moreover, the elimination of ligands that are unlikely to show a good uranyl binding affinity can release resources to focus on more promising UO22+- selective ligands. Furthermore, the results can successfully rationalize the experimentally observed loss in selectivity of amidoxime-based fibers« less

High-Fidelity Modelng and Simulation for a High Flux Isotope Reactor Low-Enriched Uranium Core Design

DOE PAGES

Betzler, Benjamin R.; Chandler, David; Davidson, Eva E.; ...

2017-05-08

A high-fidelity model of the High Flux Isotope Reactor (HFIR) with a low-enriched uranium (LEU) fuel design and a representative experiment loading has been developed to serve as a new reference model for LEU conversion studies. With the exception of the fuel elements, this HFIR LEU model is completely consistent with the current highly enriched uranium HFIR model. Results obtained with the new LEU model provide a baseline for analysis of alternate LEU fuel designs and further optimization studies. The newly developed HFIR LEU model has an explicit representation of the HFIR-specific involute fuel plate geometry, including the within-plate fuelmore » meat contouring, and a detailed geometry model of the fuel element side plates. Such high-fidelity models are necessary to accurately account for the self-shielding from 238U and the depletion of absorber materials present in the side plates. In addition, a method was developed to account for fuel swelling in the high-density LEU fuel plates during the depletion simulation. In conclusion, calculated time-dependent metrics for the HFIR LEU model include fission rate and cumulative fission density distributions, flux and reaction rates for relevant experiment locations, point kinetics data, and reactivity coefficients.« less

High-Fidelity Modelng and Simulation for a High Flux Isotope Reactor Low-Enriched Uranium Core Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Betzler, Benjamin R.; Chandler, David; Davidson, Eva E.

A high-fidelity model of the High Flux Isotope Reactor (HFIR) with a low-enriched uranium (LEU) fuel design and a representative experiment loading has been developed to serve as a new reference model for LEU conversion studies. With the exception of the fuel elements, this HFIR LEU model is completely consistent with the current highly enriched uranium HFIR model. Results obtained with the new LEU model provide a baseline for analysis of alternate LEU fuel designs and further optimization studies. The newly developed HFIR LEU model has an explicit representation of the HFIR-specific involute fuel plate geometry, including the within-plate fuelmore » meat contouring, and a detailed geometry model of the fuel element side plates. Such high-fidelity models are necessary to accurately account for the self-shielding from 238U and the depletion of absorber materials present in the side plates. In addition, a method was developed to account for fuel swelling in the high-density LEU fuel plates during the depletion simulation. In conclusion, calculated time-dependent metrics for the HFIR LEU model include fission rate and cumulative fission density distributions, flux and reaction rates for relevant experiment locations, point kinetics data, and reactivity coefficients.« less

KINKFOLD—an AutoLISP program for construction of geological cross-sections using borehole image data

NASA Astrophysics Data System (ADS)

Özkaya, Sait Ismail

2002-04-01

KINKFOLD is an AutoLISP program designed to construct geological cross-sections from borehole image or dip meter logs. The program uses the kink-fold method for cross-section construction. Beds are folded around hinge lines as angle bisectors so that bedding thickness remains unchanged. KINKFOLD may be used to model a wide variety of parallel fold structures, including overturned and faulted folds, and folds truncated by unconformities. The program accepts data from vertical or inclined boreholes. The KINKFOLD program cannot be used to model fault drag, growth folds, inversion structures or disharmonic folds where the bed thickness changes either because of deformation or deposition. Faulted structures and similar folds can be modelled by KINKFOLD by omitting dip measurements within fault drag zones and near axial planes of similar folds.

A simple tectonic model for crustal accretion in the Slave Province: A 2.7-2.5 Ga granite greenstone terrane

NASA Technical Reports Server (NTRS)

Hoffman, P. F.

1986-01-01

A prograding (direction unspecified) trench-arc system is favored as a simple yet comprehensive model for crustal generation in a 250,000 sq km granite-greenstone terrain. The model accounts for the evolutionary sequence of volcanism, sedimentation, deformation, metamorphism and plutonism, observed througout the Slave province. Both unconformable (trench inner slope) and subconformable (trench outer slope) relations between the volcanics and overlying turbidities; and the existence of relatively minor amounts of pre-greenstone basement (microcontinents) and syn-greenstone plutons (accreted arc roots) are explained. Predictions include: a varaiable gap between greenstone volcanism and trench turbidite sedimentation (accompanied by minor volcanism) and systematic regional variations in age span of volcanism and plutonism. Implications of the model will be illustrated with reference to a 1:1 million scale geological map of the Slave Province (and its bounding 1.0 Ga orogens).

Bonding in uranium(V) hexafluoride based on the experimental electron density distribution measured at 20 K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gianopoulos, Christopher G.; Zhurov, Vladimir V.; Minasian, Stefan G.

The electron density distribution of [PPh 4][UF 6] was obtained from high-resolution X-ray diffraction data measured at 20 K. The electron density was modeled with an augmented Hansen–Coppens multipolar formalism. Topological analysis reveals that the U–F bond is of incipient covalent nature. Theoretical calculations add further support to the bonding description gleaned from the experimental model. The impact of the uranium anomalous dispersion terms on the refinement is also discussed.

Bonding in uranium(V) hexafluoride based on the experimental electron density distribution measured at 20 K

DOE PAGES

Gianopoulos, Christopher G.; Zhurov, Vladimir V.; Minasian, Stefan G.; ...

2017-02-06

The electron density distribution of [PPh 4][UF 6] was obtained from high-resolution X-ray diffraction data measured at 20 K. The electron density was modeled with an augmented Hansen–Coppens multipolar formalism. Topological analysis reveals that the U–F bond is of incipient covalent nature. Theoretical calculations add further support to the bonding description gleaned from the experimental model. The impact of the uranium anomalous dispersion terms on the refinement is also discussed.

[Absorption of Uranium with Tea Oil Tree Sawdust Modified by Succinic Acid].

PubMed

Zhang, Xiao-feng; Chen, Di-yun; Peng, Yan; Liu, Yong-sheng; Xiong, Xue-ying

2015-05-01

In order to explore how the modification of succinic acid improves the adsorption of tea oil tree sawdust for uranium, the tea oil tree sawdust was modified by succinic acid, after the pretreatments of crushing, screening, alkalization and acidification. Infrared analysis indicated carboxylic acid groups and ester groups were added to the sawdust after modification, and scanning electron microscope demonstrated after modification the appearance of tea oil tree sawdust was transferred from the structure like compact and straight stripped into the structure like loose and wrinkled leaves, which meant modification increased its inner pores. By the static experiments, effects of reaction time between adsorbent and solvent, dosage of adsorbent, temperature, pH value and initial concentration of uranium were investigated. The results showed that after the modification by succinic acid, the absorption rate of tea oil tree sawdust for uranium increased significantly by about 20% in 12.5 mg · L(-1) initial concentration uranium solution. Adsorption equilibrium was achieved within 180 min, and the kinetic data can be well described by the pseudo-second-order kinetic model. The experimental adsorption isotherm followed the Langmuir and Freundlich models. In addition, the maximum adsorption amounts of tea oil tree sawdust after modification calculated from Langmuir equation raised from 21.413 3 to 31.545 7 mg · g(-1) at 35°C and pH 4.0.

Investigations into the Reusability of Amidoxime-Based Polymeric Adsorbents for Seawater Uranium Extraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuo, Li-Jung; Pan, Horng-Bin; Wai, Chien M.

The ability to re-use amidoxime-based polymeric adsorbents is a critical component in reducing the overall cost of the technology to extract uranium from seawater. This report describes an evaluation of adsorbent reusability in multiple re-use (adsorption/stripping) cycles in real seawater exposures with potassium bicarbonate (KHCO3) elution using several amidoxime-based polymeric adsorbents. The KHCO3 elution technique achieved ~100% recovery of uranium adsorption capacity in the first re-use. Subsequent re-uses showed significant drops in adsorption capacity. After the 4th re-use with the ORNL AI8 adsorbent, the 56-day adsorption capacity dropped to 28% of its original capacity. FTIR spectra revealed that there wasmore » a conversion of the amidoxime ligands to carboxylate groups during extended seawater exposure, becoming more significant with longer the exposure time. Ca and Mg adsorption capacities also increased with each re-use cycle supporting the hypothesis that long term exposure resulted in converting amidoxime to carboxylate, enhancing the adsorption of Ca and Mg. Shorter seawater exposure (adsorption/stripping) cycles (28 vs. 42 days) had higher adsorption capacities after re-use, but the shorter exposure cycle time did not produce an overall better performance in terms of cumulative exposure time. Recovery of uranium capacity in re-uses may also vary across different adsorbent formulations. Through multiple re-use the adsorbent AI8 can harvest 10 g uranium/kg adsorbent in ~140 days, using a 28-day adsorption/stripping cycle, a performance much better than would be achieved with a single use of the adsorbent through very long-term exposure (saturation capacity = 7.4 g U/kg adsorbent). A time dependent seawater exposure model to evaluate the cost associated with reusing amidoxime-based adsorbents in real seawater exposures was developed. The cost to extract uranium from seawater ranged from $610-830/kg U was predicted. Model simulation suggests that a short seawater exposure cycle (< 15 days) is the optimal deployment period for lower uranium production cost in seawater uranium mining.« less

Genetic and grade and tonnage models for sandstone-hosted roll-type uranium deposits, Texas Coastal Plain, USA

USGS Publications Warehouse

Hall, Susan M.; Mihalasky, Mark J.; Tureck, Kathleen; Hammarstrom, Jane M.; Hannon, Mark

2017-01-01

The coincidence of a number of geologic and climatic factors combined to create conditions favorable for the development of mineable concentrations of uranium hosted by Eocene through Pliocene sandstones in the Texas Coastal Plain. Here 254 uranium occurrences, including 169 deposits, 73 prospects, 6 showings and 4 anomalies, have been identified. About 80 million pounds of U3O8 have been produced and about 60 million pounds of identified producible U3O8 remain in place. The development of economic roll-type uranium deposits requires a source, large-scale transport of uranium in groundwater, and deposition in reducing zones within a sedimentary sequence. The weight of the evidence supports a source from thick sequences of volcanic ash and volcaniclastic sediment derived mostly from the Trans-Pecos volcanic field and Sierra Madre Occidental that lie west of the region. The thickest accumulations of source material were deposited and preserved south and west of the San Marcos arch in the Catahoula Formation. By the early Oligocene, a formerly uniformly subtropical climate along the Gulf Coast transitioned to a zoned climate in which the southwestern portion of Texas Coastal Plain was dry, and the eastern portion humid. The more arid climate in the southwestern area supported weathering of volcanic ash source rocks during pedogenesis and early diagenesis, concentration of uranium in groundwater and movement through host sediments. During the middle Tertiary Era, abundant clastic sediments were deposited in thick sequences by bed-load dominated fluvial systems in long-lived channel complexes that provided transmissive conduits favoring transport of uranium-rich groundwater. Groundwater transported uranium through permeable sandstones that were hydrologically connected with source rocks, commonly across formation boundaries driven by isostatic loading and eustatic sea level changes. Uranium roll fronts formed as a result of the interaction of uranium-rich groundwater with either (1) organic-rich debris adjacent to large long-lived fluvial channels and barrier–bar sequences or (2) extrinsic reductants entrained in formation water or discrete gas that migrated into host units via faults and along the flanks of salt domes and shale diapirs. The southwestern portion of the region, the Rio Grande embayment, contains all the necessary factors required for roll-type uranium deposits. However, the eastern portion of the region, the Houston embayment, is challenged by a humid environment and a lack of source rock and transmissive units, which may combine to preclude the deposition of economic deposits. A grade and tonnage model for the Texas Coastal Plain shows that the Texas deposits represent a lower tonnage subset of roll-type deposits that occur around the world, and required aggregation of production centers into deposits based on geologic interpretation for the purpose of conducting a quantitative mineral resource assessment.

User Guide for VISION 3.4.7 (Verifiable Fuel Cycle Simulation) Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacob J. Jacobson; Robert F. Jeffers; Gretchen E. Matthern

2011-07-01

The purpose of this document is to provide a guide for using the current version of the Verifiable Fuel Cycle Simulation (VISION) model. This is a complex model with many parameters and options; the user is strongly encouraged to read this user guide before attempting to run the model. This model is an R&D work in progress and may contain errors and omissions. It is based upon numerous assumptions. This model is intended to assist in evaluating 'what if' scenarios and in comparing fuel, reactor, and fuel processing alternatives at a systems level. The model is not intended as amore » tool for process flow and design modeling of specific facilities nor for tracking individual units of fuel or other material through the system. The model is intended to examine the interactions among the components of a fuel system as a function of time varying system parameters; this model represents a dynamic rather than steady-state approximation of the nuclear fuel system. VISION models the nuclear cycle at the system level, not individual facilities, e.g., 'reactor types' not individual reactors and 'separation types' not individual separation plants. Natural uranium can be enriched, which produces enriched uranium, which goes into fuel fabrication, and depleted uranium (DU), which goes into storage. Fuel is transformed (transmuted) in reactors and then goes into a storage buffer. Used fuel can be pulled from storage into either separation or disposal. If sent to separations, fuel is transformed (partitioned) into fuel products, recovered uranium, and various categories of waste. Recycled material is stored until used by its assigned reactor type. VISION is comprised of several Microsoft Excel input files, a Powersim Studio core, and several Microsoft Excel output files. All must be co-located in the same folder on a PC to function. You must use Powersim Studio 8 or better. We have tested VISION with the Studio 8 Expert, Executive, and Education versions. The Expert and Education versions work with the number of reactor types of 3 or less. For more reactor types, the Executive version is currently required. The input files are Excel2003 format (xls). The output files are macro-enabled Excel2007 format (xlsm). VISION 3.4 was designed with more flexibility than previous versions, which were structured for only three reactor types - LWRs that can use only uranium oxide (UOX) fuel, LWRs that can use multiple fuel types (LWR MF), and fast reactors. One could not have, for example, two types of fast reactors concurrently. The new version allows 10 reactor types and any user-defined uranium-plutonium fuel is allowed. (Thorium-based fuels can be input but several features of the model would not work.) The user identifies (by year) the primary fuel to be used for each reactor type. The user can identify for each primary fuel a contingent fuel to use if the primary fuel is not available, e.g., a reactor designated as using mixed oxide fuel (MOX) would have UOX as the contingent fuel. Another example is that a fast reactor using recycled transuranic (TRU) material can be designated as either having or not having appropriately enriched uranium oxide as a contingent fuel. Because of the need to study evolution in recycling and separation strategies, the user can now select the recycling strategy and separation technology, by year.« less

Revised Lithostratigraphy of the Sonsela Member (Chinle Formation, Upper Triassic) in the Southern Part of Petrified Forest National Park, Arizona

PubMed Central

Martz, Jeffrey W.; Parker, William G.

2010-01-01

Background Recent revisions to the Sonsela Member of the Chinle Formation in Petrified Forest National Park have presented a three-part lithostratigraphic model based on unconventional correlations of sandstone beds. As a vertebrate faunal transition is recorded within this stratigraphic interval, these correlations, and the purported existence of a depositional hiatus (the Tr-4 unconformity) at about the same level, must be carefully re-examined. Methodology/Principal Findings Our investigations demonstrate the neglected necessity of walking out contacts and mapping when constructing lithostratigraphic models, and providing UTM coordinates and labeled photographs for all measured sections. We correct correlation errors within the Sonsela Member, demonstrate that there are multiple Flattops One sandstones, all of which are higher than the traditional Sonsela sandstone bed, that the Sonsela sandstone bed and Rainbow Forest Bed are equivalent, that the Rainbow Forest Bed is higher than the sandstones at the base of Blue Mesa and Agate Mesa, that strata formerly assigned to the Jim Camp Wash beds occur at two stratigraphic levels, and that there are multiple persistent silcrete horizons within the Sonsela Member. Conclusions/Significance We present a revised five-part model for the Sonsela Member. The units from lowest to highest are: the Camp Butte beds, Lot's Wife beds, Jasper Forest bed (the Sonsela sandstone)/Rainbow Forest Bed, Jim Camp Wash beds, and Martha's Butte beds (including the Flattops One sandstones). Although there are numerous degradational/aggradational cycles within the Chinle Formation, a single unconformable horizon within or at the base of the Sonsela Member that can be traced across the entire western United States (the “Tr-4 unconformity”) probably does not exist. The shift from relatively humid and poorly-drained to arid and well-drained climatic conditions began during deposition of the Sonsela Member (low in the Jim Camp Wash beds), well after the Carnian-Norian transition. PMID:20174475

3D Architecture and evolution of the Po Plain-Northern Adriatic Foreland basin during Plio-Pleistocene time

NASA Astrophysics Data System (ADS)

Amadori, Chiara; Toscani, Giovanni; Ghielmi, Manlio; Maesano, Francesco Emanuele; D'Ambrogi, Chiara; Lombardi, Stefano; Milanesi, Riccardo; Panara, Yuri; Di Giulio, Andrea

2017-04-01

The Pliocene-Pleistocene tectonic and sedimentary evolution of the eastern Po Plain and northern Adriatic Foreland Basin (PPAF) (extended ca. 35,000 km2) was the consequence of severe Northern Apennine compressional activity and climate-driven eustatic changes. According with the 2D seismic interpretation, facies analysis and sequence stratigraphy approach by Ghielmi et al. (2013 and references therein), these tectono-eustatic phases generated six basin-scale unconformities referred as Base Pliocene (PL1), Intra-Zanclean (PL2), Intra-Piacenzian (PL3), Gelasian (PL4), Base Calabrian (PS1) and Late Calabrian (PS2). We present a basin-wide detailed 3D model of the PPAF region, derived from the interpretation of these unconformities in a dense network of seismic lines (ca. 6,000 km) correlated with more than 200 well stratigraphies (courtesy of ENI E&P). The initial 3D time-model has been time-to-depth converted using the 3D velocity model created with Vel-IO 3D, a tool for 3D depth conversions and then validated and integrated with depth domain dataset from bibliography and well log. Resultant isobath and isopach maps are produced to inspect step-by-step the basin paleogeographic evolution; it occurred through alternating stages of simple and fragmented foredeeps. Changes in the basin geometry through time, from the inner sector located in the Emilia-Romagna Apennines to the outermost region (Veneto and northern Adriatic Sea), were marked by repeated phases of outward migration of two large deep depocenters located in front of Emilia arcs on the west, and in front of Ferrara-Romagna thrusts on the east. During late Pliocene-early Pleistocene, the inner side of the Emilia-Romagna arcs evolved into an elongated deep thrust-top basin due to a strong foredeep fragmentation then, an overall tectono-stratigraphic analysis shows also a decreasing trend of tectonic intensity of the Northern Apennine since Pleistocene until present.

Biological pathways of exposure and ecotoxicity values for uranium and associated radionuclides: Chapter D in Hydrological, geological, and biological site characterization of breccia pipe uranium deposits in Northern Arizona

USGS Publications Warehouse

Hinck, Jo E.; Linder, Greg L.; Finger, Susan E.; Little, Edward E.; Tillitt, Donald E.; Kuhne, Wendy

2010-01-01

This chapter compiles available chemical and radiation toxicity information for plants and animals from the scientific literature on naturally occurring uranium and associated radionuclides. Specifically, chemical and radiation hazards associated with radionuclides in the uranium decay series including uranium, thallium, thorium, bismuth, radium, radon, protactinium, polonium, actinium, and francium were the focus of the literature compilation. In addition, exposure pathways and a food web specific to the segregation areas were developed. Major biological exposure pathways considered were ingestion, inhalation, absorption, and bioaccumulation, and biota categories included microbes, invertebrates, plants, fishes, amphibians, reptiles, birds, and mammals. These data were developed for incorporation into a risk assessment to be conducted as part of an environmental impact statement for the Bureau of Land Management, which would identify representative plants and animals and their relative sensitivities to exposure of uranium and associated radionuclides. This chapter provides pertinent information to aid in the development of such an ecological risk assessment but does not estimate or derive guidance thresholds for radionuclides associated with uranium. Previous studies have not attempted to quantify the risks to biota caused directly by the chemical or radiation releases at uranium mining sites, although some information is available for uranium mill tailings and uranium mine closure activities. Research into the biological impacts of uranium exposure is strongly biased towards human health and exposure related to enriched or depleted uranium associated with the nuclear energy industry rather than naturally occurring uranium associated with uranium mining. Nevertheless, studies have reported that uranium and other radionuclides can affect the survival, growth, and reproduction of plants and animals. Exposure to chemical and radiation hazards is influenced by a plant’s or an animal’s life history and surrounding environment. Various species of plants, invertebrates, fishes, amphibians, reptiles, birds, and mammals found in the segregation areas that are considered species of concern by State and Federal agencies were included in the development of the site-specific food web. The utilization of subterranean habitats (burrows in uranium-rich areas, burrows in waste rock piles or reclaimed mining areas, mine tunnels) in the seasonally variable but consistently hot, arid environment is of particular concern in the segregation areas. Certain species of reptiles, amphibians, birds, and mammals in the segregation areas spend significant amounts of time in burrows where they can inhale or ingest uranium and other radionuclides through digging, eating, preening, and hibernating. Herbivores may also be exposed though the ingestion of radionuclides that have been aerially deposited on vegetation. Measured tissues concentrations of uranium and other radionuclides are not available for any species of concern in the segregation areas. The sensitivity of these animals to uranium exposure is unknown based on the existing scientific literature, and species-specific uranium presumptive effects levels were only available for two endangered fish species known to inhabit the segregation areas. Overall, the chemical toxicity data available for biological receptors of concern were limited, although chemical and radiation toxicity guidance values are available from several sources. However, caution should be used when directly applying these values to northern Arizona given the unique habitat and life history strategies of biological receptors in the segregation areas and the fact that some guidance values are based on models rather than empirical (laboratory or field) data. No chemical toxicity information based on empirical data is available for reptiles, birds, or wild mammals; therefore, the risks associated with uranium and other radionuclides are unknown for these biota.

Origin and evolution of the Candlelight Reef-Sand Clay system, St. Croix.

USGS Publications Warehouse

Gerhard, L.C.

1981-01-01

Candlelight reef is the buttressing western terminus of the northeastern St. Croix reef system, caused by a combination of paleotopography and longshore drift which created a stable pile of detrital material at this position. Reef colonization proceeded eastward along the former slope break on the limestone terrace; turbid gyres along the eastern margin of the former Southgate drainage prevented further westward colonization. The presence of detrital cobbles in Sand Cay and Candlelight reef is explained by this model. An unconformity between underlying fine-grained quartzose rocks and overlying carbonates, need represent only an eustatic sea level rise rather than any fundamental tectonic event.-from Author

Mineralogy and diagenesis of low-permeability sandstones of Late Cretaceous age, Piceance Creek Basin, northwestern Colorado

USGS Publications Warehouse

Hansley, Paula L.; Johnson, Ronald C.

1980-01-01

This report presents preliminary results of a mineralogic and diagenetic study of some low-permeability sandstones from measured surface sections and cores obtained from drill holes in the Piceance Creek Basin of northwestern Colorado. A documentation of the mineralogy and diagenetic history will aid in the exploration for natural gas and in the development of recovery technology in these low-permability sandstones. These sandstones are in the nonmarine upper part of the Mesaverde Formation (or Group) of Late Cretaceous age and are separated from overlying lower Tertiary rocks by a major regional unconformity. Attention is focused on the sandstone units of the Ohio Creek Member, which directly underlies the unconformity; however, comparisons between the mineralogy of the Ohio Creek strata and that of the underlying sandstone units are made whenever possible. The Ohio Creek is a member of the Hunter Canyon Formation (Mesaverde Group) in the southwestern part of the basin, and the Mesaverde Formation in the southern and central parts of the basin. The detrital mineralogy is fairly constant throughout all of these nonrnarine Cretaceous sandstone units; however, in the southeastern part of the basin, there is an increase in percentage of feldspar, quartzite, and igneous rock fragments in sandstones of the Ohio Creek Member directly underlying the unconformity. In the southwestern part of the basin, sandstones of the Ohio Creek Member are very weathered and are almost-entirely comprised of quartz, chert, and kaolinite. A complex diagenetic history, partly related to the overlying unconformity, appears to be responsible for transforming these sandstones into potential gas reservoirs. The general diagenetic sequence for the entire Upper Cretaceous interval studied is interpreted to be (early to late): early(?) calcite cement, chlorite, quartz overgrowths, calcite cement, secondary porosity, analcime (surface only), kaolinite and illite, and late carbonate cements. Authigenic high-iron chlorite, which occurs on grain rims and in pore throats, is primarily responsible for the low-permeability of the subsurface sandstones of the Ohio Creek Member in the center of the basin. Kaolinite is the most abundant pore-filling authigenic clay in these sandstones, from the southwestern part of the basin and is responsible for their distinctive white-weathering color in outcrop. In the sandstones below the Ohio Creek Member, however, chlorite and kaolinite occur locally, and authigenic calcite and illite are more abundant. The occurrence and distribution of secondary porosity is one of the most important aspects of the diagenetic history of these sandstones. It is present as moldic intra- and intergranular porosity, as well as microporosity among authigenic clay pariicles. Although present locally in most sandstone units, secondary porosity is particularly common in the uppermost sandstone units and is interpreted to have formed primarily asa result ofweathering during the time represented by the Cretaceous-Tertiary unconformity.

Uranium from Seawater Program Review; Fuel Resources Uranium from Seawater Program DOE Office of Nuclear Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2013-07-01

For nuclear energy to remain sustainable in the United States, economically viable sources of uranium beyond terrestrial ores must be developed. The goal of this program is to develop advanced adsorbents that can extract uranium from seawater at twice the capacity of the best adsorbent developed by researchers at the Japan Atomic Energy Agency (JAEA), 1.5 mg U/g adsorbent. A multidisciplinary team from Oak Ridge National Laboratory, Lawrence Berkeley National Laboratory, Pacific Northwest National Laboratory, and the University of Texas at Austin was assembled to address this challenging problem. Polymeric adsorbents, based on the radiation grafting of acrylonitrile and methacrylicmore » acid onto high surface-area polyethylene fibers followed by conversion of the nitriles to amidoximes, have been developed. These poly(acrylamidoxime-co-methacrylic acid) fibers showed uranium adsorption capacities for the extraction of uranium from seawater that exceed 3 mg U/g adsorbent in testing at the Pacific Northwest National Laboratory Marine Sciences Laboratory. The essence of this novel technology lies in the unique high surface-area trunk material that considerably increases the grafting yield of functional groups without compromising its mechanical properties. This technology received an R&D100 Award in 2012. In addition, high surface area nanomaterial adsorbents are under development with the goal of increasing uranium adsorption capacity by taking advantage of the high surface areas and tunable porosity of carbon-based nanomaterials. Simultaneously, de novo structure-based computational design methods are being used to design more selective and stable ligands and the most promising candidates are being synthesized, tested and evaluated for incorporation onto a support matrix. Fundamental thermodynamic and kinetic studies are being carried out to improve the adsorption efficiency, the selectivity of uranium over other metals, and the stability of the adsorbents. Understanding the rate-limiting step of uranium uptake from seawater is also essential in designing an effective uranium recovery system. Finally, economic analyses have been used to guide these studies and highlight what parameters, such as capacity, recyclability, and stability, have the largest impact on the cost of extraction of uranium from seawater. Initially, the cost estimates by the JAEA for extraction of uranium from seawater with braided polymeric fibers functionalized with amidoxime ligands were evaluated and updated. The economic analyses were subsequently updated to reflect the results of this project while providing insight for cost reductions in the adsorbent development through “cradle-to-grave” case studies for the extraction process. This report highlights the progress made over the last three years on the design, synthesis, and testing of new materials to extract uranium for seawater. This report is organized into sections that highlight the major research activities in this project: (1) Chelate Design and Modeling, (2) Thermodynamics, Kinetics and Structure, (3) Advanced Polymeric Adsorbents by Radiation Induced Grafting, (4) Advanced Nanomaterial Adsorbents, (5) Adsorbent Screening and Modeling, (6) Marine Testing, and (7) Cost and Energy Assessment. At the end of each section, future research directions are briefly discussed to highlight the challenges that still remain to reduce the cost of extractions of uranium for seawater. Finally, contributions from the Nuclear Energy University Programs (NEUP), which complement this research program, are included at the end of this report.« less

Uptake of Uranium from Seawater by Amidoxime-Based Polymeric Adsorbent: Field Experiments, Modeling, and Updated Economic Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Jungseung; Tsouris, Constantinos; Oyola, Yatsandra

2014-04-09

Uranium recovery from seawater has been investigated for several decades for the purpose of securing nuclear fuel for energy production. In this study, field column experiments have been performed at the Marine Sciences Laboratory of the Pacific Northwest National Laboratory (PNNL) using a laboratory-proven, amidoxime-based polymeric adsorbent developed at the Oak Ridge National Laboratory (ORNL). The adsorbent was packed either in in-line filters or in flow-through columns. The maximum amount of uranium uptake from seawater was 3.3 mg of U/g of adsorbent after 8 weeks of contact between the adsorbent and seawater. This uranium adsorption amount was about 3 timesmore » higher than the maximum amount achieved in this study by a leading adsorbent developed at the Japan Atomic Energy Agency (JAEA).« less

Large fluctuations of shallow seas in low-lying Southeast Asia driven by mantle flow

NASA Astrophysics Data System (ADS)

Zahirovic, Sabin; Flament, Nicolas; Dietmar Müller, R.; Seton, Maria; Gurnis, Michael

2016-09-01

The Sundaland continental promontory, as the core of Southeast Asia, is one of the lowest lying continental regions, with half of the continental area presently inundated by a shallow sea. The role of mantle convection in driving long-wavelength topography and vertical motion of the lithosphere in this region has often been ignored when interpreting regional stratigraphy, including a widespread Late Cretaceous-Eocene unconformity, despite a consensus that Southeast Asia is presently situated over a large-amplitude dynamic topography low resulting from long-term post-Pangea subduction. We use forward numerical models to link mantle flow with surface tectonics and compare predicted trends of dynamic topography with eustasy and regional paleogeography to determine the influence of mantle convection on regional basin histories. A Late Cretaceous collision of Gondwana-derived terranes with Sundaland choked the active margin, leading to slab breakoff and a ˜10-15 Myr-long subduction hiatus. A subduction hiatus likely resulted in several hundred meters of dynamic uplift and emergence of Sundaland between ˜80 and 60 Ma and may explain the absence of a Late Cretaceous-Eocene sedimentary record. Renewed subduction from ˜60 Ma reinitiated dynamic subsidence of Sundaland, leading to submergence from ˜40 Ma despite falling long-term global sea levels. Our results highlight a complete "down-up-down" dynamic topography cycle experienced by Sundaland, with transient dynamic topography manifesting as a major regional unconformity in sedimentary basins.

Compared in vivo efficiency of nanoemulsions unloaded and loaded with calixarene and soapy water in the treatment of superficial wounds contaminated by uranium.

PubMed

Grivès, Sophie; Phan, Guillaume; Bouvier-Capely, Céline; Suhard, David; Rebière, François; Agarande, Michelle; Fattal, Elias

2017-04-01

No emergency decontamination treatment is currently available in the case of radiological skin contamination by uranium compounds. First responders in the workplace or during an industrial nuclear accident must be able to treat internal contamination through skin. For this purpose, a calixarene nanoemulsion was developed for the treatment of intact skin or superficial wounds contaminated by uranium, and the decontamination efficiency of this nanoemulsion was investigated in vitro and ex vivo. The present work addresses the in vivo decontamination efficiency of this nanoemulsion, using a rat model. This efficiency is compared to the radio-decontaminant soapy water currently used in France (Trait rouge ® ) in the workplace. The results showed that both calixarene-loaded nanoemulsion and non-loaded nanoemulsion allowed a significant decontamination efficiency compared to the treatment with soapy water. Early application of the nanoemulsions on contaminated excoriated rat skin allowed decreasing the uranium content by around 85% in femurs, 95% in kidneys and 93% in urines. For skin wounded by microneedles, mimicking wounds by microstings, nanoemulsions allowed approximately a 94% decrease in the uranium retention in kidneys. However, specific chelation of uranium by calixarene molecules within the nanoemulsion was not statistically significant, probably because of the limited calixarene-to-uranium molar ratio in these experiment conditions. Moreover, these studies showed that the soapy water treatment potentiates the transcutaneous passage of uranium, thus making it bioavailable, in particular when the skin is superficially wounded. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Efficient rolling texture predictions and texture-sensitive properties of α-uranium foils

DOE PAGES

Steiner, Matthew A.; Klein, Robert W.; Calhoun, Christopher A.; ...

2017-01-01

Here, finite element (FE) analysis was used to simulate the strain history of an α-uranium foil during cold-rolling, with the sheet modeled as an isotropic elastoplastic continuum. The resulting strain history was then used as input for a viscoplastic self-consistent (VPSC) polycrystal plasticity model to simulate crystallographic texture evolution. Mid-plane textures predicted via the combined FE→VPSC approach show alignment of the (010) poles along the rolling direction (RD), and the (001) poles along the normal direction (ND) with a symmetric splitting along RD. The surface texture is similar to that of the mid-plane, but with a shear-induced asymmetry that favorsmore » one of the RD split features of the (001) pole figure. Both the mid-plane and surface textures predicted by the FE→VPSC approach agree with published experimental results for cold-rolled α-uranium plates, as well as predictions made by a more computationally intensive full-field crystal plasticity based finite element model. α-uranium foils produced by cold-rolling must typically undergo a final recrystallization anneal to restore ductility prior to their final application, resulting in significant texture evolution from the cold-rolled plate deformation texture. Using the texture measured from a foil in the final recrystallized state, coefficients of the thermal expansion and elastic stiffness tensors were calculated using a thermo-elastic self-consistent model, and the anisotropic yield loci and flow curves along the RD, TD, and ND were predicted using the VPSC code.« less

Efficient rolling texture predictions and texture-sensitive properties of α-uranium foils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steiner, Matthew A.; Klein, Robert W.; Calhoun, Christopher A.

Here, finite element (FE) analysis was used to simulate the strain history of an α-uranium foil during cold-rolling, with the sheet modeled as an isotropic elastoplastic continuum. The resulting strain history was then used as input for a viscoplastic self-consistent (VPSC) polycrystal plasticity model to simulate crystallographic texture evolution. Mid-plane textures predicted via the combined FE→VPSC approach show alignment of the (010) poles along the rolling direction (RD), and the (001) poles along the normal direction (ND) with a symmetric splitting along RD. The surface texture is similar to that of the mid-plane, but with a shear-induced asymmetry that favorsmore » one of the RD split features of the (001) pole figure. Both the mid-plane and surface textures predicted by the FE→VPSC approach agree with published experimental results for cold-rolled α-uranium plates, as well as predictions made by a more computationally intensive full-field crystal plasticity based finite element model. α-uranium foils produced by cold-rolling must typically undergo a final recrystallization anneal to restore ductility prior to their final application, resulting in significant texture evolution from the cold-rolled plate deformation texture. Using the texture measured from a foil in the final recrystallized state, coefficients of the thermal expansion and elastic stiffness tensors were calculated using a thermo-elastic self-consistent model, and the anisotropic yield loci and flow curves along the RD, TD, and ND were predicted using the VPSC code.« less

Efficient rolling texture predictions and texture-sensitive thermomechanical properties of α-uranium foils

NASA Astrophysics Data System (ADS)

Steiner, Matthew A.; Klein, Robert W.; Calhoun, Christopher A.; Knezevic, Marko; Garlea, Elena; Agnew, Sean R.

2017-11-01

Finite element (FE) analysis was used to simulate the strain history of an α-uranium foil during cold straight-rolling, with the sheet modeled as an isotropic elastoplastic continuum. The resulting strain history was then used as input for a viscoplastic self-consistent (VPSC) polycrystal plasticity model to simulate crystallographic texture evolution. Mid-plane textures predicted via the combined FE→VPSC approach show alignment of the (010) poles along the rolling direction (RD), and the (001) poles along the normal direction (ND) with a symmetric splitting along RD. The surface texture is similar to that of the mid-plane, but with a shear-induced asymmetry that favors one of the RD split features of the (001) pole figure. Both the mid-plane and surface textures predicted by the FE→VPSC approach agree with published experimental results for cold straight-rolled α-uranium plates, as well as predictions made by a more computationally intensive full-field crystal plasticity based finite element model. α-uranium foils produced by cold-rolling must typically undergo a recrystallization anneal to restore ductility prior to their final application, resulting in significant texture evolution from the cold-rolled plate deformation texture. Using the texture measured from a foil in the final recrystallized state, coefficients of thermal expansion and the elastic stiffness tensors were calculated using a thermo-elastic self-consistent model, and the anisotropic yield loci and flow curves along the RD, TD, and ND were predicted using the VPSC code.

Uranium in surface soils: an easy-and-quick assay combining X-ray diffraction and fluorescence qualitative data

NASA Astrophysics Data System (ADS)

Figueiredo, M. O.; Silva, T. P.; Batista, M. J.; Leote, J.; Ferreira, M. L.; Limpo, V.

2009-04-01

Portugal has been a uranium-producer since the beginning of the last century. The uranium-rich area of Alto Alentejo, East-central Portugal, was identified more than fifty years ago [1]. Almost all the uranium-bearing mineralization occurs in schistose rocks of the contact metamorphic aureole produced by intrusion of the Hercynian monzonitic granite of Alto Alentejo into the pre-Ordovitian schist-greywacke complex forming deposits of vein and dissemination type. The Nisa uranium-reservoir, situated at the sharp border of a large and arch shaped granite pluton, was identified in 1957 [2] but its exploitation was considered economically impracticable until recently. However, its existence and the accumulated detritus of these prospect efforts are a concern for local populations [3]. A study of the near-surface soils close to the Nisa reservoir was therefore undertaken to assess the uranium retention by adsorption on clay components under the form of uranyl ions, [UO2]2+ [4-6] and its eventual release into the aquifer groundwater. As an attempt to very quickly appraise the presence of uranium in as-collected near-surface sediment samples a combination of laboratory X-ray techniques was designed: X-ray diffraction (XRD) to identify the mineral phases and roughly estimate its relative proportion plus X-ray fluorescence spectrometry in wavelength dispersive mode (XRF-WDS) to ascertain the presence of uranium and tentatively evaluate its content by comparison with selected chemical components of the soil. A description of the experimental methodology adopted for the implemented easy-and-quick uranium assay is presented. Obtained results compare quite well to the data of certified time-consuming analytical tests of uranium in those soil samples. [1] L. Pilar (1966) Conditions of formation of Nisa uranium deposit (in Portuguese). Comunic. Serv. Geol. Portugal, tomo L, 50-85. [2] C. Gonçalves & J.V. Teixeira Lopes (1971) Uranium deposit of Nisa: geological aspects of its discovery and valorisation (in Portuguese). Internal Rept., JEN, 20 pp. [3] http://www.naturtejo.com [4] J.A. Davis et al. (2006) Processes affecting transport of uranium in a suboxic aquifer. Phys. Chem. of the Earth 31, 548-555. [5] Y. Arai et al. (2007) Spectroscopic evidence for uranium bearing precipitates in Vadose zone sediments at the Hanford 300-Area site. Environ. Sci. Technol. 41, 4633-4639. [6] A. Kremleva, S. Krüger & N. Rösch (2008) Density functional model studies of uranyl adsorption on (001) surfaces of kaolinite. Langmuir 24, 9515-9524.

Stratigraphic development and hydrothermal activity in the central western Cascade Range, Oregon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cummings, M.L.; Bull, M.K.; Pollock, J.M.

1990-11-10

Two volcanic sequences bounded by erosional unconformities compose the stratigraphy of the North Santiam mining district, Western Cascade Range, Oregon. Diorite, grandodiorite, and leucocratic quartz porphyry dikes, stocks, and sills intrude the breccias, flows, and tuffs of a volcanic center in the older Sardine Formation. Tourmaline-bearing breccia pipes are associated with the porphyritic granodiorite intrusions. An erosional unconformity separates the Sardine Formation from the overlying Elk Lake formation. The alteration patterns in the two formations are consistent with the development of hydrothermal systems during the eruption of each formation. However, the development of the two hydrothermal systems is separated bymore » a period of erosion of the older volcanic pile. Early formation of mineralization that resembles porphyry copper deposits occurred within the Sardine Formation, and later, after eruption of the Elk Lake formation, epithermal veins and alteration developed along faults, fractures, and the margins of dikes in the Sardine Formation.« less

Diagenetic silica enrichment and late-stage groundwater activity in Gale crater, Mars

USGS Publications Warehouse

Frydenvang, Jens; Gasda, Patrick J.; Hurowitz, Joel A.; Grotzinger, John P.; Wiens, Roger C.; Newsom, Horton E.; Edgett, Ken S.; Watkins, Jessica; Bridges, John C.; Maurice, Sylvestre; Fisk, Martin R.; Johnson, Jeffrey R.; Rapin, William; Stein, Nathan; Clegg, Sam M.; Schwenzer, S. P.; Bedford, C.; Edwards, P.; Mangold, Nicolas; Cousin, Agnes; Anderson, Ryan; Payre, Valerie; Vaniman, David; Blake, David; Lanza, Nina L.; Gupta, Sanjeev; Van Beek, Jason; Sautter, Violaine; Meslin, Pierre-Yves; Rice, Melissa; Milliken, Ralf; Gellert, Ralf; Thompson, Lucy; Clark, Ben C.; Sumner, Dawn Y.; Fraeman, Abigail A.; Kinch, Kjartan M; Madsen, Morten B.; Mitofranov, Igor; Jun, Insoo; Calef, Fred J.; Vasavada, Ashwin R.

2017-01-01

Diagenetic silica enrichment in fracture-associated halos that crosscut lacustrine and unconformably overlying aeolian sedimentary bedrock is observed on the lower north slope of Aeolis Mons in Gale crater, Mars. The diagenetic silica enrichment is colocated with detrital silica enrichment observed in the lacustrine bedrock yet extends into a considerably younger, unconformably draping aeolian sandstone, implying that diagenetic silica enrichment postdates the detrital silica enrichment. A causal connection between the detrital and diagenetic silica enrichment implies that water was present in the subsurface of Gale crater long after deposition of the lacustrine sediments and that it mobilized detrital amorphous silica and precipitated it along fractures in the overlying bedrock. Although absolute timing is uncertain, the observed diagenesis likely represents some of the most recent groundwater activity in Gale crater and suggests that the timescale of potential habitability extended considerably beyond the time that the lacustrine sediments of Aeolis Mons were deposited.

Combining particle-tracking and geochemical data to assess public supply well vulnerability to arsenic and uranium

USGS Publications Warehouse

Hinkle, S.R.; Kauffman, L.J.; Thomas, M.A.; Brown, C.J.; McCarthy, K.A.; Eberts, S.M.; Rosen, Michael R.; Katz, B.G.

2009-01-01

Flow-model particle-tracking results and geochemical data from seven study areas across the United States were analyzed using three statistical methods to test the hypothesis that these variables can successfully be used to assess public supply well vulnerability to arsenic and uranium. Principal components analysis indicated that arsenic and uranium concentrations were associated with particle-tracking variables that simulate time of travel and water fluxes through aquifer systems and also through specific redox and pH zones within aquifers. Time-of-travel variables are important because many geochemical reactions are kinetically limited, and geochemical zonation can account for different modes of mobilization and fate. Spearman correlation analysis established statistical significance for correlations of arsenic and uranium concentrations with variables derived using the particle-tracking routines. Correlations between uranium concentrations and particle-tracking variables were generally strongest for variables computed for distinct redox zones. Classification tree analysis on arsenic concentrations yielded a quantitative categorical model using time-of-travel variables and solid-phase-arsenic concentrations. The classification tree model accuracy on the learning data subset was 70%, and on the testing data subset, 79%, demonstrating one application in which particle-tracking variables can be used predictively in a quantitative screening-level assessment of public supply well vulnerability. Ground-water management actions that are based on avoidance of young ground water, reflecting the premise that young ground water is more vulnerable to anthropogenic contaminants than is old ground water, may inadvertently lead to increased vulnerability to natural contaminants due to the tendency for concentrations of many natural contaminants to increase with increasing ground-water residence time.

Assessment of nonpoint source chemical loading potential to watersheds containing uranium waste dumps and human health hazards associated with uranium exploration and mining, Red, White, and Fry Canyons, southeastern Utah, 2007

USGS Publications Warehouse

Beisner, Kimberly R.; Marston, Thomas M.; Naftz, David L.; Snyder, Terry; Freeman, Michael L.

2010-01-01

During May, June, and July 2007, 58 solid-phase samples were collected from abandoned uranium mine waste dumps, background sites, and adjacent streambeds in Red, White, and Fry Canyons in southeastern Utah. The objectives of this sampling program were to (1) assess the nonpoint-source chemical loading potential to ephemeral and perennial drainage basins from uranium waste dumps and (2) assess potential effects on human health due to recreational activities on and around uranium waste dumps on Bureau of Land Management property. Uranium waste-dump samples were collected using solid-phase sampling protocols. After collection, solid-phase samples were homogenized and extracted in the laboratory using a leaching procedure. Filtered (0.45 micron) water samples were obtained from the field leaching procedure and were analyzed for major and trace elements at the Inductively Coupled Plasma-Mass Spectrometry Metals Analysis Laboratory at the University of Utah. A subset of the solid-phase samples also were digested with strong acids and analyzed for major ions and trace elements at the U.S. Geological Survey Geologic Division Laboratory in Denver, Colorado. For the initial ranking of chemical loading potential for uranium waste dumps, results of leachate analyses were compared with existing aquatic-life and drinking-water-quality standards. To assess potential effects on human health, solid-phase digestion values for uranium were compared to soil screening levels (SSL) computed using the computer model RESRAD 6.5 for a probable concentration of radium. One or more chemical constituents exceeded aquatic life and drinking-water-quality standards in approximately 64 percent (29/45) of the leachate samples extracted from uranium waste dumps. Most of the uranium waste dump sites with elevated trace-element concentrations in leachates were located in Red Canyon. Approximately 69 percent (31/45) of the strong acid digestible soil concentration values were greater than a calculated SSL. Uranium waste dump sites with elevated leachate and total digestible concentrations may need to be further investigated to determine the most appropriate remediation method.

Risk evaluation of uranium mining: A geochemical inverse modelling approach

NASA Astrophysics Data System (ADS)

Rillard, J.; Zuddas, P.; Scislewski, A.

2011-12-01

It is well known that uranium extraction operations can increase risks linked to radiation exposure. The toxicity of uranium and associated heavy metals is the main environmental concern regarding exploitation and processing of U-ore. In areas where U mining is planned, a careful assessment of toxic and radioactive element concentrations is recommended before the start of mining activities. A background evaluation of harmful elements is important in order to prevent and/or quantify future water contamination resulting from possible migration of toxic metals coming from ore and waste water interaction. Controlled leaching experiments were carried out to investigate processes of ore and waste (leached ore) degradation, using samples from the uranium exploitation site located in Caetité-Bahia, Brazil. In experiments in which the reaction of waste with water was tested, we found that the water had low pH and high levels of sulphates and aluminium. On the other hand, in experiments in which ore was tested, the water had a chemical composition comparable to natural water found in the region of Caetité. On the basis of our experiments, we suggest that waste resulting from sulphuric acid treatment can induce acidification and salinization of surface and ground water. For this reason proper storage of waste is imperative. As a tool to evaluate the risks, a geochemical inverse modelling approach was developed to estimate the water-mineral interaction involving the presence of toxic elements. We used a method earlier described by Scislewski and Zuddas 2010 (Geochim. Cosmochim. Acta 74, 6996-7007) in which the reactive surface area of mineral dissolution can be estimated. We found that the reactive surface area of rock parent minerals is not constant during time but varies according to several orders of magnitude in only two months of interaction. We propose that parent mineral heterogeneity and particularly, neogenic phase formation may explain the observed variation of the reactive mineral surface area. The formation of coatings on dissolving mineral surfaces significantly reduces the amount of surface available to react with fluids. Our results show that negatively charged ion complexes, responsible for U transport, decreases when alkalinity and rock buffer capacity is similarly lower. Carbonate ion pairs however, may increase U mobility when radionuclide concentration is high and rock buffer capacity is low. The present work helps to orient future monitoring of this site in Brazil as well as of other sites where uranium is linked to igneous rock formations, without the presence of sulphides. Monitoring SO4 migration (in acidic leaching uranium sites) seems to be an efficient and simple way to track different hazards, especially in tropical conditions, where the succession of dry and wet periods increases the weathering action of the residual H2SO4. Nevertheless, models of risk evaluation should take into account reactive surface areas and neogenic minerals since they determine the U ion complex formation, which in turn, controls uranium mobility in natural systems. Keywords: uranium mining, reactive mineral surface area, uranium complexes, inverse modelling approach, risk evaluation

A 26 million year gap in the central Arctic record at the greenhouse-icehouse transition: Looking for clues

USGS Publications Warehouse

Sangiorgi, F.; Brumsack, H.-J.; Willard, D.A.; Schouten, S.; Stickley, C.E.; O'Regan, M.; Reichart, G.-J.; Sinninghe, Damste J.S.; Brinkhuis, H.

2008-01-01

The Cenozoic record of the Lomonosov Ridge (central Arctic Ocean) recovered during Integrated Ocean Drilling Program (IODP) Expedition 302 revealed an unexpected 26 Ma hiatus, separating middle Eocene (???44.4 Ma) from lower Miocene sediments (???18.2 Ma). To elucidate the nature of this unconformity, we performed a multiproxy palynological (dinoflagellate cysts, pollen, and spores), micropaleontological (siliceous microfossils), inorganic, and organic (Tetra Ether Index of lipids with 86 carbon atoms (TEX86) and Branched and Isoprenoid Tetraether (BIT)) geochemical analysis of the sediments from ???5 m below to ???7 m above the hiatus. Four main paleoenvironmental. phases (A-D) are recognized in the sediments encompassing the unconformity, two below (A-B) and two above (C-D): (A) Below the hiatus, proxies show relatively warm temperatures, with Sea Surface Temperatures (TEX86-derived SSTs) of about 8??C and high fresh to brackish water influence. (B) Approaching the hiatus, proxies indicate a cooling trend (TEX86-derived SSTs of ???5??C), increased freshwater influence, and progressive shoaling of the Lomonosov Ridge drilling site, located close to or at sea level. (C) The interval directly above the unconformity contains sparse reworked Cretaceous to Oligocene dinoflagellate cysts. Sediments were deposited in a relatively shallow, restricted marine environment. Proxies show the simultaneous influence of both fresh and marine waters, with alternating oxic and anoxic conditions. Pollen indicates a relatively cold climate. Intriguingly, TEX86-derived SSTs are unexpectedly high, ???15-19??C. Such warm surface waters may be partially explained by the ingression of warmer North Atlantic waters after the opening of the Fram Strait during the early Miocene. (D) Sediments of the uppermost interval indicate a phase of extreme oxic conditions, and a well-ventilated environment, which occurred after the complete opening of the Fram Strait. Importantly, and in contrast with classical postrifting thermal subsidence models for passive margins, our data suggest that sediment erosion and/or nondeposition that generated the hiatus was likely due to a progressive shoaling of the Lomonosov Ridge. A shallow water setting both before and after the hiatus suggests that the Lomonosov Ridge remained at or near sea level for the duration of the gap in the sedimentary record. Interacting sea level changes and/ or tectonic activity (possibly uplift) must be invoked as possible causes for such a long hiatus. Copyright 2008 by the American Geophysical Union.

Revisiting the Mesozoic opening of the Southeastern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Marton, G.; Pascoe, R. P.

2016-12-01

The Southeastern Gulf of Mexico (SEGOM) is defined here as the seaway between Yucatan and Florida, south of the Tampa Embayment. This area is regarded as a southward propagating rift in the Gulf of Mexico. There is an overwhelming amount of previous evidence that the Yucatan block rotated counterclockwise about 42 degrees around a pole located just north of present-day Cuba (23oN, 84oW) during the Late Jurassic to Earliest Cretaceous oceanic spreading phase. North of the pole in the SEGOM the rotational movement of Yucatan was accommodated by a uniformly increasing amount of SW-NE extension. The degree of extension north of 25oN was large enough to result in rifting and oceanic spreading. Lack of salt in the area south of the Tampa embayment indicates that the SEGOM was not affected by the large amount of NW-SE continental extension as observed in the rest of the Gulf of Mexico. Thus, the area between Yucatan and the Sarasota arch remained a land bridge between the proto- GOM and the Proto-Caribbean and formed a barrier to salt deposition. During the period of late Jurassic oceanic crust formation (and Yucatan rotation), the southern tip of the oceanic spreading center propagated south from 27oN to 25oN, or about 220 km. In the 220 km long zone from 25oN to the pole (23oN) the rotation of Yucatan was accommodated by continental rifting only. The validity of the above outlined propagating rift model in the SEGOM is also supported by the age differences in the observed post-rift unconformities along its margins. At the edge of the salt basin to the north, the post-rift unconformity in the upper crust occurs at the base of the Louann salt and thus is Callovian in age. In the southern continental rift segment of the SEGOM, a seismic to well tie at the DSDP Site 535 shows that the post-rift unconformity is no younger than Late Berriasian to Early Valanginian. This latter age bracket constrains a) the cessation of continental rifting in the SEGOM, b) the time when the Yucatan block docked in its present day location relative to North America, and c) the time when oceanic crust formation ceased in the Gulf of Mexico.

A model to predict thermal conductivity of irradiated U-Mo dispersion fuel

NASA Astrophysics Data System (ADS)

Burkes, Douglas E.; Huber, Tanja K.; Casella, Andrew M.

2016-05-01

Numerous global programs are focused on the continued development of existing and new research and test reactor fuels to achieve maximum attainable uranium loadings to support the conversion of a number of the world's remaining high-enriched uranium fueled reactors to low-enriched uranium fuel. Some of these programs are focused on assisting with the development and qualification of a fuel design that consists of a uranium-molybdenum (U-Mo) alloy dispersed in an aluminum matrix as one option for reactor conversion. Thermal conductivity is an important consideration in determining the operational temperature of the fuel and can be influenced by interaction layer formation between the dispersed phase and matrix and upon the concentration of the dispersed phase within the matrix. This paper extends the use of a simple model developed previously to study the influence of interaction layer formation as well as the size and volume fraction of fuel particles dispersed in the matrix, Si additions to the matrix, and Mo concentration in the fuel particles on the effective thermal conductivity of the U-Mo/Al composite during irradiation. The model has been compared to experimental measurements recently conducted on U-Mo/Al dispersion fuels at two different fission densities with acceptable agreement. Observations of the modeled results indicate that formation of an interaction layer and subsequent consumption of the matrix reveals a rather significant effect on effective thermal conductivity. The modeled interaction layer formation and subsequent consumption of the high thermal conductivity matrix was sensitive to the average dispersed fuel particle size, suggesting this parameter as one of the most effective in minimizing thermal conductivity degradation of the composite, while the influence of Si additions to the matrix in the model was highly dependent upon irradiation conditions.

A model to predict thermal conductivity of irradiated U–Mo dispersion fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burkes, Douglas E.; Huber, Tanja K.; Casella, Andrew M.

The Office of Materials Management and Minimization Reactor Conversion Program continues to develop existing and new research and test reactor fuels to achieve maximum attainable uranium loadings to support the conversion of a number of the world’s remaining high-enriched uranium fueled reactors to low-enriched uranium fuel. The program is focused on assisting with the development and qualification of a fuel design that consists of a uranium-molybdenum (U-Mo) alloy dispersed in an aluminum matrix as one option for reactor conversion. Thermal conductivity is an important consideration in determining the operational temperature of the fuel and can be influenced by interaction layermore » formation between the dispersed phase and matrix and upon the concentration of the dispersed phase within the matrix. This paper extends the use of a simple model developed previously to study the influence of interaction layer formation as well as the size and volume fraction of fuel particles dispersed in the matrix, Si additions to the matrix, and Mo concentration in the fuel particles on the effective thermal conductivity of the U-Mo/Al composite during irradiation. The model has been compared to experimental measurements recently conducted on U-Mo/Al dispersion fuels at two different fission densities with acceptable agreement. Observations of the modeled results indicate that formation of an interaction layer and subsequent consumption of the matrix reveals a rather significant effect on effective thermal conductivity. The modeled interaction layer formation and subsequent consumption of the high thermal conductivity matrix was sensitive to the average dispersed fuel particle size, suggesting this parameter as one of the most effective in minimizing thermal conductivity degradation of the composite, while the influence of Si additions to the matrix in the model was highly dependent upon irradiation conditions.« less

Uranium Sequestration During Biostimulated Reduction and In Response to the Return of Oxic Conditions In Shallow Aquifers

USGS Publications Warehouse

Fuller, Christopher C.; Johnson, Kelly J.; Akstin, Katherine; Singer, David M.; Yabusaki, Steven B.; Fang, Yilin; Fuhrmann, M.

2015-01-01

A proposed approach for groundwater remediation of uranium contamination is to generate reducing conditions by stimulating the growth of microbial populations through injection of electron donor compounds into the subsurface. Sufficiently reducing conditions will result in reduction of soluble hexavalent uranium, U(VI), and precipitation of the less soluble +4 oxidation state uranium, U(IV). This process is termed biostimulated reduction. A key issue in the remediation of uranium (U) contamination in aquifers by biostimulated reduction is the long term stability of the sequestered uranium. Three flow-through column experiments using aquifer sediment were used to evaluate the remobilization of bioreduced U sequestered under conditions in which biostimulation extended well into sulfate reduction to enhance precipitation of reduced sulfur phases such as iron sulfides. One column received added ferrous iron, Fe(II), increasing production of iron sulfides, to test their effect on remobilization of the sequestered uranium, either by serving as a redox buffer by competing for dissolved oxygen, or by armoring the reduced uranium. During biostimulation of the ambient microbial population with acetate, dissolved uranium was lowered by a factor of 2.5 or more with continued removal for over 110 days of biostimulation, well after the onset of sulfate reduction at ~30 days. Sequestered uranium was essentially all U(IV) resulting from the formation of nano-particulate uraninite that coated sediment grains to a thickness of a few 10’s of microns, sometimes in association with S and Fe. A multicomponent biogeochemical reactive transport model simulation of column effluents during biostimulation was generally able to describe the acetate oxidation, iron, sulfate, and uranium reduction for all three columns using parameters derived from simulations of field scale biostimulation experiments. Columns were eluted with artificial groundwater at equilibrium with atmospheric oxygen to simulate the upper limit of dissolved oxygen in recharge water. Overall about 9% of total uranium removed from solution during biostimulation was remobilized. Release of U during oxic elution was a continuous process over 140 days with dissolved uranium concentrations about 0.2 and 0.8 aM for columns with and without ferrous iron addition, respectively. Uranium remaining on the sediment was in the reduced form. The prolonged period of biostimulation and concomitant sulfate reduction appears to limit the rate of U(IV) oxidative remobilization in contrast to a large release observed for columns in previous studies that did not undergo sulfate reduction. Although continued sulfate reduction may cause decreased permeability from precipitation of iron sulfide, the greater apparent stability of the sequestered U(IV) provided by the sustained biostimulation should be considered in design of field scale remediation efforts. Remobilization of uranium following biostimulated reduction should be tested further at the field scale.

Quantifying differences in the impact of variable chemistry on equilibrium uranium(VI) adsorption properties of aquifer sediments

USGS Publications Warehouse

Stoliker, Deborah L.; Kent, Douglas B.; Zachara, John M.

2011-01-01

Uranium adsorption-desorption on sediment samples collected from the Hanford 300-Area, Richland, WA varied extensively over a range of field-relevant chemical conditions, complicating assessment of possible differences in equilibrium adsorption properties. Adsorption equilibrium was achieved in 500-1000 h although dissolved uranium concentrations increased over thousands of hours owing to changes in aqueous chemical composition driven by sediment-water reactions. A nonelectrostatic surface complexation reaction, >SOH + UO22+ + 2CO32- = >SOUO2(CO3HCO3)2-, provided the best fit to experimental data for each sediment sample resulting in a range of conditional equilibrium constants (logKc) from 21.49 to 21.76. Potential differences in uranium adsorption properties could be assessed in plots based on the generalized mass-action expressions yielding linear trends displaced vertically by differences in logKc values. Using this approach, logKc values for seven sediment samples were not significantly different. However, a significant difference in adsorption properties between one sediment sample and the fines (Kc uncertainty were improved by capturing all data points within experimental errors. The mass-action expression plots demonstrate that applying models outside the range of conditions used in model calibration greatly increases potential errors.

Chelation of UO(2)(2+) by vitamin B6 complex derivatives: synthesis and characterization of [UO2(beta-pyracinide)2(H2O)] and [UO2(Pyr2en)DMSO]Cl2{Pyr2en=N,N'-ethylenebis(pyridoxylideneiminato)}. A useful modeling of assimilation of uranium by living beings.

PubMed

Back, Davi Fernando; de Oliveira, Gelson Manzoni; Lang, Ernesto Schulz

2006-10-01

The vitamin B(6) derivatives 4-pyridoxic acid (anionic) and the Schiff base N,N'-ethylenebis(pyridoxylideneiminato) react with UO(2)(NO(3))(2) * 6H(2)O to give [UO(2)(beta-pyracinide)(2)(H(2)O)] (beta-pyracin=4-pyridoxic acid) and [UO(2)(Pyr(2)en)DMSO]Cl(2)(Pyr(2)en=N,N'-ethylenebis(pyridoxylideneiminato); DMSO=dimethyl sulfoxide). In both compounds the two uranyl oxo ligands set the axis of distorted pentagonal bipyramides. The ability of vitamin B(6) derivatives to react with UO(2)(2+) allowing the chelation of one uranium atom represents a very specific model of assimilation of uranium by living beings. It could also explain the serious damages caused by heavy or radioactive metals like uranium since their complexation "in vivo" by enzymatic systems like pyridoxal phosphate-containing enzymes would lead to a modification of the prosthetic groups of the metalloenzymes with loss of their catalytic activities.

Tertiary volcanic rocks and uranium in the Thomas Range and northern Drum Mountains, Juab County, Utah

USGS Publications Warehouse

Lindsey, David A.

1982-01-01

The Thomas Range and northern Drum Mountains have a history of volcanism, faulting, and mineralization that began about 42 m.y. (million years) ago. Volcanic activity and mineralization in the area can be divided into three stages according to the time-related occurrence of rock types, trace-element associations, and chemical composition of mineral deposits. Compositions of volcanic rocks changed abruptly from rhyodacite-quartz latite (42-39 m.y. ago) to rhyolite (38-32 m.y. ago) to alkali rhyolite (21 and 6-7 m.y. ago); these stages correspond to periods of chalcophile and siderophile metal mineralization, no mineralization(?), and lithophile metal mineralization, respectively. Angular unconformities record episodes of cauldron collapse and block faulting between the stages of volcanic activity and mineralization. The youngest angular unconformity formed between 21 and 7 m.y. ago during basin-and-range faulting. Early rhyodacite-quartz latite volcanism from composite volcanoes and fissures produced flows, breccias, and ash-flow tuff of the Drum Mountains Rhyodacite and Mt. Laird Tuff. Eruption of the Mt. Laird Tuff about 39 m.y. ago from an area north of Joy townsite was accompanied by collapse of the Thomas caldera. Part of the roof of the magma chamber did not collapse, or the magma was resurgent, as is indicated by porphyry dikes and plugs in the Drum Mountains. Chalcophile and siderophile metal mineralization, resulting in deposits of copper, gold, and manganese, accompanied early volcanism. Te middle stage of volcanic activity was characterized by explosive eruption of rhyolitic ash-flow tuffs and collapse of the Dugway Valley cauldron. Eruption of the Joy Tuff 38 m.y. ago was accompanied by subsidence of this cauldron and was followed by collapse and sliding of Paleozoic rocks from the west wall of the cauldron. Landslides in The Dell were covered by the Dell Tuff, erupted 32 m.y. ago from an unknown source to the east. An ash flow of the Needles Range(?) Formation was erupted 30-31 m.y. ago from an unknown source. Mineralization probably did not occur during the rhyolitic stage of volcanism. The last stage of volcanism was contemporaneous with basin-and-range faulting and was characterized by explosive eruption of ash and pumice, forming stratified tuff, and by quiet eruption of alkali rhyolite as viscous flows and domes. The first episode of alkali rhyolite volcanism deposited the beryllium tuff and porphyritic rhyolite members of the Spor Mountain Formation 21 m.y. ago. After a period of block faulting, the stratified tuff and alkali rhyolite of the Topaz Mountain Rhyolite were erupted 6-7 m.y. ago along faults and fault intersections. Erosion of Spor Mountain, as well as explosive eruptions through dolomite, provided abundant dolomite detritus to the beryllium tuff member. The alkali rhyolite of both formations is fluorine rich, as is evident from abundant topaz, and contains anomalous amounts of lithophile metals. Alkali rhyolite volcanism was accompanied by lithophile metal mineralization which deposited fluorite, beryllium, and uranium. The structure of the area is dominated by the Thomas caldera and the younger Dugway Valley cauldron, which is nested within the Thomas caldera; the Thomas caldera is surrounded by a rim of Paleozoic rocks at Spor Mountain and Paleozoic to Precambrian rocks in the Drum Mountains. The Joy fault and Dell fault system mark the ring-fracture zone of the Thomas caldera. These structural features began to form about 39 m.y. ago during eruption of the Mt. Laird Tuff and caldera subsidence. The Dugway Valley cauldron sank along a series of steplike normal faults southeast of Topaz Mountain in response to collapse of the magma chamber of the Joy Tuff. Caldera structure was modified by block faulting between 21 and 7 m.y. ago, the time of widespread extensional faulting in the Basin and Range Province. Vents erupted alkali rhyolite 6-7 m.y. ago along basin-and-range faults.

Stratigraphic comparison of six oil fields (WV) producing from Big Injun sandstones

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zou, X.; Donaldson, A.C.

1993-08-01

Clustered within western West Virginia, six oil fields produce from the lower Mississippian Big Injun sandstones, and three more oil fields also supplement this production either from underlying Squaw or Weir sandstones. Shales separate these sandstones that occur stratigraphically between the Sunbury Shale (maximum flooding surface) and pre-Greenbrier unconformity (maximum regressive erosional surface), and represent highstand regressive deposits associated with the postorogenic phase of foreland basin accumulation. Stratigraphic studies show two Big Injun sandstones. The upper sandstone, called the Maccrady Big Injun, is separated from the lower Price/Pocono Big Injun sandstone by red shales. Both Big Injun sandstones consist ofmore » fine-grained river-mouth bars capped by coarse-grained river-channel deposits. Although the six fields are within three adjacent counties, Maccrady Big Injun sandstones of Blue Creek (Kanawha) and Rock Creek (Roane) fields are younger and were deposited by a different fluvial-deltaic system than the Price/Pocono Big Injun sandstones of Granny Creek (Clay), Tariff (Roane) Clendenin (Clay), and Pond Fork (Kanawha) fields. Upper Weir sandstones are thick, narrow north-trending belts underlying Pond Fork and Blue Creek fields, with properties suggesting wave-dominated shoreline deposits. Allocycles spanning separate drainage systems indicate eustasy. Postorogenic flexural adjustments probably explain stacked sandstone belts with superposed paleovalleys of overlying unconformities (pre-Greenbrier, Pottsville), particularly where aligned along or parallel basement structures of Rome trough or West Virginia dome. Initially, differential subsidence or uplift during sedimentation influenced the position, geometry, trend, and distribution patterns of these reservoir sandstone, then influenced their preserved condition during erosion of pre-Greenbrier unconformity.« less

Biostratigraphy and chronostratigraphy of the area between Sarasota and Lake Okeechobee, southern Florida: An integrated approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wingard, G.L.; Edwards, L.E.; McCartan, L.

1993-03-01

Preliminary analysis of paleontologic and isotopic data from 15 coreholes, integrated with the lithostratigraphic framework, has revealed three chronostratigraphic depositional units in the subsurface of the Arcadia and Sarasota 30 [times] 60-minute quadrangles, in the southern Florida peninsula. (1) An upper Oligocene depositional unit unconformably overlies the lower Oligocene Suwannee Formation and has been dated by using [sup 87]Sr/[sup 86]Sr values and molluscs. (2) A lower and middle Miocene depositional unit has been dated on the basis of [sup 87]Sr/[sup 86]Sr values, molluscs, and dinoflagellates. The upper boundary of this unit is marked by the top of the Venice Claymore » in the western part of the study area. (3) A Pliocene and Pleistocene depositional unit, dated on the basis of [sup 87]Sr/[sup 86]Sr values, molluscs, dinoflagellates, foraminifera, ostracodes, and pollen, unconformably overlies the lower and middle Miocene beds; this unconformity represents approximately a 13-million-year gap in the record. The Pliocene and Pleistocene unit is seen in the surficial deposits of the Caloosahatchee, Tamiami, Bermont, and Fort Thompson Formations. The interpretation of Florida's geologic history is hampered by the interfingering of onlap/offlap cycles from two coastlines, a unique situation in southeastern coastal plain geology. In addition, a complex diagenetic history, mixing of carbonate and siliciclastic regimes, and lack of surface exposures make interpretation of the stratigraphic sequences difficult. The chronostratigraphic depositional units identified cut across lithofacies boundaries and allow correlation across the Florida peninsula, thus leading to the development of coherent, well-defined lithostratigraphic units.« less

Geology and evolution of the Northern Kara Sea Shelf

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vinogradov, A.

1991-08-01

The interpretation of regional multichannel seismic reflection profiles collected during 1988-1987 yields the following features of the geology of the Northern Kara Sea Shelf (NKSS). Two regional deep sedimentary basins are clearly distinguished within the NKSS. They have rather complex inner structures and contain sediments 14.0-16.0 km thick. The basin are separated from each other by a relatively narrow, linear zone of basement high which extends from Uedineniya Island on the south to Vize Island on the north, where basement depth is 1.5-4.0 km. The sedimentary sections of the basins are composed of four lithological-stratigraphical sequences separated by unconformities whichmore » correlate well with regional unconformities in adjacent land areas. The initial stages of sedimentary basin development within the NKSS date back to the late Riphean-Vendian; probably they were associated with intracontinental rifting, when up to 4 km of sediments were deposited. During the most of the Phanerozoic, regional subsidence dominated; however, the rates of subsidence were different in the western and in the eastern basins, and varied in time for each basin. The subsidence was interrupted for relatively short periods when the region was affected by uplifts and erosion which resulted in formation of regional unconformities. The seismic data gave no evidence of Caledonian or any other Phanerozoic folding within the NKSS, which is in contrast with widespread assumptions. The results show that the geological structure and evolution of the NKSS differ greatly from those of adjacent Barents and Southern Kara Sea shelves.« less

Widespread effects of middle Mississippian deformation in the Great Basin of western North America

USGS Publications Warehouse

Trexler, J.H.; Cashman, P.H.; Cole, J.C.; Snyder, W.S.; Tosdal, R.M.; Davydov, V.I.

2003-01-01

Stratigraphic analyses in central and eastern Nevada reveal the importance of a deformation event in middle Mississippian time that caused widespread deformation, uplift, and erosion. It occurred between middle Osagean and late Meramecian time and resulted in deposition of both synorogenic and postorogenic sediments. The deformation resulted in east-west shortening, expressed as east-vergent folding and east-directed thrusting; it involved sedimentary rocks of the Antler foredeep as well as strata associated with the Roberts Mountains allochthon. A latest Meramecian to early Chesterian unconformity, with correlative conformable lithofacies changes, postdates this deformation and occurs throughout Nevada. A tectonic highland-created in the middle Mississippian and lasting into the Pennsylvanian and centered in the area west and southwest of Carlin, Nevada- shed sediments eastward across the Antler foreland, burying the unconformity. Postorogenic strata are late Meramecian to early Chesterian at the base and are widespread throughout the Great Basin. The tectonism therefore occurred 20 to 30 m.y. after inception of the Late Devonian Antler orogeny, significantly extending the time span of this orogeny or representing a generally unrecognized orogenic event in the Paleozoic evolution of western North America. We propose a revised stratigraphic nomenclature for Mississippian strata in Nevada, based on detailed age control and the recognition of unconformities. This approach resolves the ambiguity of some stratigraphic names and emphasizes genetic relationships within the upper Paleozoic section. We take advantage of better stratigraphic understanding to propose two new stratigraphic units for southern and eastern Nevada: the middle Mississippian Gap Wash and Late Mississippian Captain Jack Formations.

Tectonics, topography, and river system transition in East Tibet: Insights from the sedimentary record in Taiwan

NASA Astrophysics Data System (ADS)

Lan, Qing; Yan, Yi; Huang, Chi-Yue; Clift, Peter D.; Li, Xuejie; Chen, Wenhuang; Zhang, Xingchang; Yu, Mengming

2014-09-01

The Cenozoic in East Asia is marked by major changes in tectonics, landscapes, and river systems, although the timing and nature of such changes remains disputed. We investigate the geochemistry and neodymium isotope character of Cenozoic mudstones spanning the breakup unconformity in the Western Foothills of Taiwan in order to constrain erosion and drainage development in southern China during the opening of the South China Sea. The La/Lu, Eu/Eu*, Th/Sc, Th/La, Cr/Th, and ɛNd values in these rocks show an abrupt change between ˜31 and 25 Ma. Generally the higher ɛNd values in sediments deposited prior to 31 Ma indicate erosion from Phanerozoic granitic sources exposed in coastal South China, whereas the lower ɛNd values suggest that the main sources had evolved to inland southern China by ˜25 Ma. The SHRIMP U-Pb ages of zircons from a tuff, together with biostratigraphy data constrain the breakup unconformity to be between ˜39 and 33 Ma, suggesting that the seafloor spreading in the South China Sea commenced before ˜33 Ma. This is significantly older than most of the oceanic crust preserved in the deeper part of the basin. Diachronous westward younging of the breakup unconformities and provenance changes of basins are consistent with seafloor spreading propagating from east to west. Initial spreading of the South China Sea prior to ˜33 Ma corresponds to tectonic adjustment in East Asia, including extrusion of the Indochina block and the rotation and eastward retreat of the subducting Pacific Plate.

Paleokarst and reservoir porosity in the Ordovician Beekmantown Dolomite of the central Appalachian basin

USGS Publications Warehouse

Smosna, R.; Bruner, K.R.; Riley, R.A.

2005-01-01

A karst-unconformity play at the top of the Ordovician Beekmantown Dolomite is judged to have great petroleum potential in Ohio and adjacent states; wells have high ultimate reserves and large areas remain untested. To better understand the origin, development, and distribution of Beekmantown porosity, we conducted a petrologic-stratigraphic study of cores and thin sections from 15 oil and gas wells. The massive dolomite, characterized by a hypidiotopic-idiotopic texture, formed by the replacement of stacked peritidal carbonate cycles. Secondary porosity occurs at two scales: (1) mesoscopic - breccia porosity, solution-enlarged fractures, large vugs, and caverns, and (2) microscopic - intercrystalline, intracrystalline, molds, small vugs, and microfractures. Mesoscopic pores (providing the major storage capacity in this reservoir) were produced by intrastratal solution and collapse of carbonate layers, whereas microscopic pores (connecting the larger pores) generally formed by the leaching of individual carbonate grains and crystals. Most pore types developed during periods of subaerial exposure across the carbonate bank, tied to either the numerous, though brief falls of relative sea level during Beekmantown deposition or more importantly the prolonged Knox unconformity at the close of sedimentation. The distribution of reservoir-quality porosity is quite heterogeneous, being confined vertically to a zone immediately below the unconformity and best developed laterally beneath buried hills and noses of this erosion surface. The inferred, shallow flow of ground water in the Beekmantown karst, primarily below topographic highs and above a diagenetic base level close to the water table, led to this irregular distribution of porosity.

Tectonic implications of facies patterns, Lower Permian Dry Mountain trough, east-central Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gallegos, D.M.; Snyder, W.S.; Spinosa, C.

1991-02-01

Paleozoic tectonism is indicated by a study of a west-east facies analysis transect across the northern portion of the Lower Permian Dry Mountain trough (DMT). In an attempt to characterize the Early Permian basin-filling sequences, three broadly recognizable facies packages have been identified across the DMT: the western margin facies and the central basin facies of the DMT and an eastern shelf facies. In the western margin facies of the basin, pulses of tectonic activity are recorded at McCloud Spring in the Sulphur Springs Range. Here, shallow open-marine carbonate overlies eroded Vinini Formation and, in turn, is unconformably overlain bymore » basinal marine carbonate. An unconformity also marks the contact with the overriding prograding coarse clastic facies. These abrupt transitions suggest the sediments were deposited in a tectonically active area where they preservation of Waltherian sequences is unlikely to occur. Similarly abrupt transitions are evident in the western part of the central basin facies. At Portuguese Springs n the Diamond Range, a thin basal marine conglomerate delineates Lower Permian sedimentation over the Pennsylvanian Ely Formation. Coarsening-upward basinal carbonate strata of pelagic, hemipelagic, and turbidite components overlie the basal conglomerate. this progression of sediments is unconformably overlain by a subaerial sequence of coarse clastic deposits. Within the eastern part of the central basin facies in the Maverick Spring Range, the Lower Permian sediments are open-marine siltstone, wackestone, packstone, and grainstone. The sediments are assigned to a gradually sloping ramp, indicating the effects of tectonism on this margin of the basin were subdued.« less

Thermodynamic properties of α-uranium

NASA Astrophysics Data System (ADS)

Ren, Zhiyong; Wu, Jun; Ma, Rong; Hu, Guichao; Luo, Chao

2016-11-01

The lattice constants and equilibrium atomic volume of α-uranium were calculated by Density Functional Theory (DFT). The first principles calculation results of the lattice for α-uranium are in agreement with the experimental results well. The thermodynamic properties of α-uranium from 0 to 900 K and 0-100 GPa were calculated with the quasi-harmonic Debye model. Volume, bulk modulus, entropy, Debye temperature, thermal expansion coefficient and the heat capacity of α-uranium were calculated. The calculated results show that the bulk modulus and Debye temperature increase with the increasing pressure at a given temperature while decreasing with the increasing temperature at a given pressure. Volume, entropy, thermal expansion coefficient and the heat capacity decrease with the increasing pressure while increasing with the increasing temperature. The theoretical results of entropy, Debye temperature, thermal expansion coefficient and the heat capacity show good agreement with the general trends of the experimental values. The constant-volume heat capacity shows typical Debye T3 power-law behavior at low temperature limit and approaches to the classical asymptotic Dulong-Petit limit at high temperature limit.

Experience of on-site disposal of production uranium-graphite nuclear reactor.

PubMed

Pavliuk, Alexander O; Kotlyarevskiy, Sergey G; Bespala, Evgeny V; Zakharova, Elena V; Ermolaev, Vyacheslav M; Volkova, Anna G

2018-04-01

The paper reported the experience gained in the course of decommissioning EI-2 Production Uranium-Graphite Nuclear Reactor. EI-2 was a production Uranium-Graphite Nuclear Reactor located on the Production and Demonstration Center for Uranium-Graphite Reactors JSC (PDC UGR JSC) site of Seversk City, Tomsk Region, Russia. EI-2 commenced its operation in 1958, and was shut down on December 28, 1990, having operated for the period of 33 years all together. The extra pure grade graphite for the moderator, water for the coolant, and uranium metal for the fuel were used in the reactor. During the operation nitrogen gas was passed through the graphite stack of the reactor. In the process of decommissioning the PDC UGR JSC site the cavities in the reactor space were filled with clay-based materials. A specific composite barrier material based on clays and minerals of Siberian Region was developed for the purpose. Numerical modeling demonstrated the developed clay composite would make efficient geological barriers preventing release of radionuclides into the environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

2015 Advanced Site Investigation and Monitoring Report Riverton, Wyoming, Processing Site September 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frazier, William; Campbell, Sam

The U.S. Department of Energy conducted initial groundwater characterization of the Riverton, Wyoming, Processing Site in the 1990s. The characterization culminated in a Site Observational Work Plan in 1998 that recommended a natural flushing compliance strategy. Results of verification monitoring indicated that natural flushing was generally progressing as expected until June 2010, when significant increases in contaminant concentrations were measured in several monitoring wells downgradient of the site after the area flooded. In response to the unexpected results following the flood, an enhanced characterization of the surficial aquifer was conducted in 2012, which included installation of 103 boreholes along ninemore » transects with a Geoprobe, collection of 103 water samples and 65 soil samples, laboratory tests on the soil samples, and additional groundwater modeling. This advanced site investigation report summarizes additional investigation in 2015 through the use of backhoe trenching, sonic drilling, multilevel monitoring wells, direct-push drilling, and temporary well points to collect soil and groundwater samples. Additional surface water measurements were made included the installation of a stilling well and the measurement of stream elevation along the Wind River to approximate upgradient groundwater heads. Groundwater sampling included the addition of geochemical constituents and isotopes that have not been sampled in the past to better understand post-flood conditions and the possibility of additional or ongoing contaminant sources. This sampling was performed to (1) better define the contaminant plumes, (2) verify the occurrence of persistent secondary contaminant sources, (3) better understand the reason for the contaminant spikes after a 2010 flood, and (4) assess contaminant plume stagnation near the Little Wind River. This report provides data analyses and interpretations for the 2015 site investigation that addresses these issues and provides recommendations for future efforts. Observations from trenches and sonic drilling indicate the general lithology of the shallow, unconsolidated sediments consists of a silt zone at the surface that ranges from 2.5 to 4.8 feet below ground surface, underlain by sand and gravel, underlain by the top of the weathered bedrock (Wind River Formation). Soil data from trenches and sonic drilling indicate (1) elevated concentrations of several constituents in the silt zone, likely due to the formation of evaporites, (2) uranium is the only measured element that appears to be concentrated in the silt over the groundwater contaminant plume, (3) in the former tailings impoundment area, there may be a thin unsaturated zone with elevated uranium in the native material just below the fill, (4) in the former tailings impoundment area, slightly higher uranium concentrations occur in the underlying saturated sand and gravel, and (5) several bedrock samples have a unique geochemical signature, generally related to a higher silt content. Assessment of groundwater flow included measuring river elevations along the Wind River and installing the temporary well points adjacent to the Little Wind River that provided additional data points to refine contours for water table elevations. These data confirm past interpretations of groundwater flow to the southeast across the site toward the Little Wind River. Hydraulic head elevations between paired surficial and semiconfined aquifer wells indicate variable vertical gradients across the site with the potential for upward and downward flow. Additional direct-push drilling and groundwater sampling confirmed the contaminant plume configuration, but it also revealed a low-sulfate-concentration zone at the edge of the former tailings impoundment. Temporary well points provided better definition of plume concentrations at the bank of the Little Wind River, and data from these wells indicate plume discharge to the river. Additional sampling in an area southwest of the plume that had elevated uranium groundwater concentrations in the past did not have any uranium concentrations above the U.S. Environmental Protection Agency maximum concentration limit for uranium. Results from multilevel monitoring wells indicate some geochemical differences with depth, but overall concentrations are similar to those in nearby conventional monitoring wells in the long-term monitoring program. Geochemistry data from these multilevel monitoring wells confirm the general increase in contaminant concentrations toward the river and toward the plume centerline for chloride, sulfate, and uranium but highlight geochemical controls on calcium. Iron data indicate slightly reducing conditions, especially near water table and bedrock surfaces, with more oxidizing conditions in the middle of the sand and gravel. Uranium activity ratios (234U/238U) confirm the uranium plume in the surficial aquifer as being mill related, and the area to the southwest outside the plume as natural, non-mill related. In the semiconfined aquifer, evidence of aquifer connection and impacts from the mill is inconclusive. Values of δD and δ 18O suggest water is derived from different sources and tritium data confirm that the semiconfined aquifer water is generally older than the surficial aquifer water. However, these data do indicate some groundwater communication from the surficial aquifer into the semiconfined aquifer, which resulted in δD and δ 18O and tritium values in the semiconfined aquifer that are more similar to those in the surficial aquifer. Values of δ 34S sulfate in the semiconfined aquifer combined with sulfate concentrations indicate the potential for some mill- related sulfate in the semiconfined aquifer, albeit limited to an area near and beneath the former tailings impoundment. Uranium and molybdenum concentrations in the semiconfined aquifer are below groundwater standards in all wells. However, the elevated molybdenum concentrations at one semiconfined aquifer well underneath the former tailings impoundment suggests a mill- derived source for the uranium and molybdenum in that well. It is possible that aquifer cross- communication occurred when the tailings impoundment was active and created a higher head. Current cross-communication appears unlikely given the large differences in tritium values and an upward hydraulic head at this location. Nine domestic wells are located within the institutional control boundary (eight in the confined aquifer and one in the semiconfined aquifer). Uranium and molybdenum concentrations in all samples collected from these wells were one or two orders of magnitude below the groundwater standards. Surface water flow in the Little Wind River in September 2015 was low compared to historical averages for that time of year. As a result, the uranium concentration measured in the Little Wind River was at a historical maximum at the sampling location upstream of the site. However, the impact of uranium discharge from the groundwater plume into the Little Wind River was not measureable. Elevated sulfate concentrations were observed in an outfall ditch related to an active sulfuric acid plant. Uranium concentrations in the oxbow lake remain at concentrations above the groundwater standard. Plume contaminant concentrations had returned to levels found prior to the 2010 flood by the end of 2015. However, these concentrations still exceed model predictions for natural flushing, and the current data indicate that natural flushing to achieve remediation goals within the 100-year time period is not likely, especially with the high potential for additional floods in the update to the conceptual site model (CSM), soil data indicate additional contaminant sources, specifically uranium, in evaporites within the silt layer over the uranium plume and in naturally reduced zones (NRZs). Additional zones of slightly elevated uranium concentration are in the native sediments just above the water table but below the fill layer in the former tailings impoundment area. This area also has slightly elevated uranium in the sand and gravel below the water table. Mass balance calculations indicate that small amounts of dissolution in any of these zones with increased uranium in the solid phase can produce groundwater uranium concentrations above the groundwater standard and could account for the post-flood uranium spike. The additional uranium near the former tailings impoundment provides a mechanism for a continuing source for the uranium plume that was not considered in earlier natural flushing models. In addition, uranium released from the silt layer or the NRZs seasonally and during flooding may add uranium to the groundwater plume near the Little Wind River. These mechanisms provide a possible explanation for plume persistence, along with spikes in concentrations during floods, that creates the current plume configuration. Additional updates to the CSM include (1) chloride flushes more rapidly than uranium beneath the former mill site, (2) chloride in the silt layer provides a scenario in which chloride cannot be used as a conservative tracer (especially in areas prone to flooding), (3) uranium concentrations with depth can be variable (especially below NRZs), and (4) calcite and gypsum solubility limits appear to provide important geochemical controls on groundwater geochemistry. The conclusion of this study provides several recommendations for additional work to refine the CSM and continue assessment of the natural flushing compliance strategy. Recommendations for additional work include targeted soil and groundwater sampling to assess geochemical conditions, distribution of contaminants, and groundwater/surface water interaction; additional column tests to provide data for geochemical modeling; and development of an updated groundwater flow model, which will be used in conjunction with a geochemical model to assess the viability of the natural flushing compliance strategy.« less

Retardation of uranium and thorium by a cementitious backfill developed for radioactive waste disposal.

PubMed

Felipe-Sotelo, M; Hinchliff, J; Field, L P; Milodowski, A E; Preedy, O; Read, D

2017-07-01

The solubility of uranium and thorium has been measured under the conditions anticipated in a cementitious, geological disposal facility for low and intermediate level radioactive waste. Similar solubilities were obtained for thorium in all media, comprising NaOH, Ca(OH) 2 and water equilibrated with a cement designed as repository backfill (NRVB, Nirex Reference Vault Backfill). In contrast, the solubility of U(VI) was one order of magnitude higher in NaOH than in the remaining solutions. The presence of cellulose degradation products (CDP) results in a comparable solubility increase for both elements. Extended X-ray Absorption Fine Structure (EXAFS) data suggest that the solubility-limiting phase for uranium corresponds to a becquerelite-type solid whereas thermodynamic modelling predicts a poorly crystalline, hydrated calcium uranate phase. The solubility-limiting phase for thorium was ThO 2 of intermediate crystallinity. No breakthrough of either uranium or thorium was observed in diffusion experiments involving NRVB after three years. Nevertheless, backscattering electron microscopy and microfocus X-ray fluorescence confirmed that uranium had penetrated about 40 μm into the cement, implying active diffusion governed by slow dissolution-precipitation kinetics. Precise identification of the uranium solid proved difficult, displaying characteristics of both calcium uranate and becquerelite. Copyright © 2017 Elsevier Ltd. All rights reserved.

Transmutation of uranium and thorium in the particle field of the Quinta sub-critical assembly

NASA Astrophysics Data System (ADS)

Hashemi-Nezhad, S. R.; Asquith, N. L.; Voronko, V. A.; Sotnikov, V. V.; Zhadan, Alina; Zhuk, I. V.; Potapenko, A.; Husak, Krystsina; Chilap, V.; Adam, J.; Baldin, A.; Berlev, A.; Furman, W.; Kadykov, M.; Khushvaktov, J.; Kudashkin, I.; Mar'in, I.; Paraipan, M.; Pronskih, V.; Solnyshkin, A.; Tyutyunnikov, S.

2018-03-01

The fission rates of natural uranium and thorium were measured in the particle field of Quinta, a 512 kg natural uranium target-blanket sub-critical assembly. The Quinta assembly was irradiated with deuterons of energy 4 GeV from the Nuclotron accelerator of the Joint Institute for Nuclear Research (JINR), Dubna, Russia. Fission rates of uranium and thorium were measured using Gamma spectroscopy and fission track techniques. The production rate of 239Np was also measured. The obtained experimental results were compared with Monte Carlo predictions using the MCNPX 2.7 code employing the physics and fission-evaporation models of INCL4-ABLA, CEM03.03 and LAQGSM03.03. Some of the neutronic characteristics of the Quinta are compared with the "Energy plus Transmutation (EpT)" subcritical assembly, which is composed of a lead target and natU blanket. This comparison clearly demonstrates the importance of target material, neutron moderator and reflector types on the performance of a spallation neutron driven subcritical system. As the dimensions of the Quinta are very close to those of an optimal multi-rod-uranium target, the experimental and Monte Carlo calculation results presented in this paper provide insights on the particle field within a uranium target as well as in Accelerator Driven Systems in general.

Determination of the solubility and size distribution of radioactive aerosols in the uranium processing plant at NRCN.

PubMed

Kravchik, T; Oved, S; Paztal-Levy, O; Pelled, O; Gonen, R; German, U; Tshuva, A

2008-01-01

Inhalation is the main route of internal exposure to radioactive aerosols in the nuclear industry. To assess the radiation dose from the intake of these aerosols, it is necessary to know their physical (aerodynamic diameter distribution) and chemical (dissolution rate in extracellular lung fluid) characteristics. Air samples were taken from the uranium processing plant at the Nuclear Research Center, Negev. Measurements of aerodynamic diameter distribution using a cascade impactor indicated an average activity median aerodynamic diameter value close to 5 microm, in accordance with the recent recommended values of International Commission on Radiological Protection (ICRP) model. Solubility profiles of these aerosols were determined by performing in vitro solubility tests over 100 d in a simultant solution of the extracellular fluid. The tests indicated that the uranium aerosols should be assigned to an absorption between Types M and S (as defined by the ICRP Publication 66 model).

Bioremediation of uranium-contaminated groundwater: a systems approach to subsurface biogeochemistry.

PubMed

Williams, Kenneth H; Bargar, John R; Lloyd, Jonathan R; Lovley, Derek R

2013-06-01

Adding organic electron donors to stimulate microbial reduction of highly soluble U(VI) to less soluble U(IV) is a promising strategy for immobilizing uranium in contaminated subsurface environments. Studies suggest that diagnosing the in situ physiological status of the subsurface community during uranium bioremediation with environmental transcriptomic and proteomic techniques can identify factors potentially limiting U(VI) reduction activity. Models which couple genome-scale in silico representations of the metabolism of key microbial populations with geochemical and hydrological models may be able to predict the outcome of bioremediation strategies and aid in the development of new approaches. Concerns remain about the long-term stability of sequestered U(IV) minerals and the release of co-contaminants associated with Fe(III) oxides, which might be overcome through targeted delivery of electrons to select microorganisms using in situ electrodes. Copyright © 2012 Elsevier Ltd. All rights reserved.

Pseudopotential for ab initio calculations of uranium compounds

NASA Astrophysics Data System (ADS)

Smirnov, G. S.; Pisarev, V. V.; Stegailov, V. V.

2018-01-01

The density functional theory (DFT) is a research tool of the highest importance for electronic structure calculations. It is often the only affordable method for ab initio calculations of complex materials. The pseudopotential approach allows reducing the total number of electrons in the model that speeds up calculations. However, there is a lack of pseudopotentials for heavy elements suitable for condensed matter DFT models. In this work, we present a pseudopotential for uranium developed in the Goedecker-Teter-Hutter form. Its accuracy is illustrated using several molecular and solid-state calculations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shepherd, James; Fairweather, Michael; Hanson, Bruce C.

The oxidation of spent uranium carbide fuel, a candidate fuel for Generation IV nuclear reactors, is an important process in its potential reprocessing cycle. However, the oxidation of uranium carbide in air is highly exothermic. A model has therefore been developed to predict the temperature rise, as well as other useful information such as reaction completion times, under different reaction conditions in order to help in deriving safe oxidation conditions. Finite difference-methods are used to model the heat and mass transfer processes occurring during the reaction in two dimensions and are coupled to kinetics found in the literature.

Paleozoic and Mesozoic deformations in the central Sierra Nevada, California

USGS Publications Warehouse

Nokleberg, Warren J.; Kistler, Ronald Wayne

1980-01-01

Analysis of structural and stratigraphic data indicates that several periods of regional deformation, consisting of combined folding, faulting, cataclasis, and regional metamorphism, occurred throughout the central Sierra Nevada during Paleozoic and Mesozoic time. The oldest regional deformation occurred alono northward trends during the Devonian and Mississippian periods in most roof pendants containing lower Paleozoic metasedimentary rocks at the center and along the crest of the range. This deformation is expressed in some roof pendants by an angular unconformity separating older thrice-deformed from younger twice-deformed Paleozoic metasedimentary rocks. The first Mesozoic deformation, which consisted of uplift and erosion and was accompanied by the onset of Andean-type volcanism during the Permian and Triassic, is expressed by an angular unconformity in several roof pendants from the Saddlebag Lake to the Mount Morrison areas. This unconformity is defined by Permian and Triassic andesitic to rhyolitic metavolcanic rocks unconformably overlying more intensely deformed Pennsylvanian, Permian(?), and older metasedimentary rocks. A later regional deformation occurred during the Triassic along N. 20?_30? W. trends in Permian and Triassic metavolcanic rocks of the Saddlebag Lake and Mount Dana roof pendants, in upper Paleozoic rocks of the Pine Creek roof pendant, and in the Calaveras Formation of the western metamorphic belt; the roof pendants are crosscut by Upper Triassic granitic rocks of the Lee Vining intrusive epoch. A still later period of Early and Middle Jurassic regional deformation occurred along N. 30?-60? E. trends in upper Paleozoic rocks of the Calaveras Formation of the western metamorphic belt. A further period of deformation was the Late Jurassic Nevadan orogeny, which occurred along N. 20?_40? W. trends in Upper Jurassic rocks of the western metamorphic belt that are crosscut by Upper Jurassic granitic rocks of the Yosemite intrusive epoch. Structures of similar age occur in intensely deformed oceanic-lithospheric and syntectonic plutonic rocks of the lower Kings River area, in Jurassic metavolcanic rocks of the Ritter Range roof pendant, and in Triassic metasedimentary rocks of the Mineral King roof pendant. The final Mesozoic deformation occurred along N. 50?-80? W. trends in both high-country roof pendants and the lower Kings River area; structures of this generation are crosscut by relatively undeformed Upper Cretaceous granitic rocks of the Cathedral Range intrusive epoch.

Environmental and ice volume changes based on seismic stratigraphy in Sabrina Coast, East Antarctica: Preliminary results from NBP1402

NASA Astrophysics Data System (ADS)

Gulick, S. P. S.; Fernandez-Vasquez, R. A.; Frederick, B.; Saustrup, S., Sr.; Domack, E. W.; Lavoie, C.; Shevenell, A.; Blankenship, D. D.; Leventer, A.

2014-12-01

In 2014, the R/V Nathaniel B. Palmer (NBP1402) sailed to a virtually unexplored continental shelf along the Sabrina Coast, East Antarctica. The shelf contains the sedimentary record of environmental and ice volume changes within the Aurora Subglacial Basin (ASB), which is presently occupied by ~7 m sea level-rise equivalent of ice. We acquired 750 km of high-resolution seismic data proximal to the Reynolds Trough and Moscow University Ice Shelf glacial systems west of the Dalton Ice Tongue using dual 45/45 cu. in. G.I. guns and a 24 ch. streamer with 3.125 m groups providing a vertical resolution of ~3 m simultaneously with CHIRP data. These are the first images of this margin acquired and show a remarkable set of sequence stratigraphic transitions. Crystalline basement is at the seafloor landward and buried seaward with a transition to smoother reflection interface. Reflective sedimentary strata overlie the basement, dip seaward, and are capped by a landward-dipping regional angular unconformity. Above this are a series of transparent seismic facies that, along with the middle to outer shelf seafloor, dip landward towards a shelf-oblique glacial trough. The older, seaward-dipping strata include a deeper series of units that display at least three stratal architectures interpreted to be shelf deltas implying a pre-glacial, fluvial environment within the drainage basin. Above these sequences, the seismic facies transition to surfaces exhibiting significant erosion, small u-shaped valleys, and channel fill sequences, all of which are reminiscent of temperate glacial features. We interpret these sequences as including sub-ice tunnel valleys and grounding zone wedges with interspersed non-glacial to pro-glacial deposits. Increasing glaciogenic facies upsection suggests a gradual fluvial to glacial transition and increasing glacial extent with time. The subsequent transition to ice sheets is marked by erosion to basement landward and the angular unconformity seaward. The unconformity is overlain by glacial diamict, representing an incomplete record of cold-based glaciations after the ASB became ice-filled. Correlations with cores collected above and below the unconformity and deltaic unit should allow us to determine the ages of these transitions from fluvial to polythermal to ice sheets in East Antarctica.

Bioremediation of Uranium-Contaminated Groundwater using Engineered Injection and Extraction

NASA Astrophysics Data System (ADS)

Greene, J. A.; Neupauer, R.; Ye, M.; Kasprzyk, J. R.; Mays, D. C.; Curtis, G. P.

2017-12-01

During in-situ remediation of contaminated groundwater, a treatment chemical is injected into the contaminated groundwater to react with and degrade the contaminant, with reactions occurring where the treatment chemical contacts the contaminant. Traditional in-situ groundwater remediation relies on background groundwater flow for spreading of treatment chemicals into contaminant plumes. Engineered Injection and Extraction (EIE), in which time-varying induced flow fields are used to actively spread the treatment chemical into the contaminant plume, has been developed to increase contact between the contaminant and treatment chemical, thereby enhancing contaminant degradation. EIE has been investigated for contaminants that degrade through irreversible bimolecular reaction with a treatment chemical, but has not been investigated for a contaminant governed by reversible reactions. Uranium primarily occurs in its aqueous, mobile form, U(VI), in the environment but can be bioreduced to its sparingly soluble, immobile form, U(IV), by iron reducing bacteria stimulated by an acetate amendment. In this study, we investigate the ability of EIE to facilitate and sustain favorable conditions to immobilize uranium during remediation, and to prevent re-mobilization of uranium into the aqueous phase after active remediation has ended. Simulations in this investigation are conducted using a semi-synthetic model based on physical and chemical conditions at the Naturita Uranium Mill Tailings Remedial Action (UMTRA) site in southwestern Colorado and the Old Rifle UMTRA site in western Colorado. The EIE design is optimized for the synthetic model using the Borg multi-objective evolutionary algorithm.

Thermal radiative and thermodynamic properties of solid and liquid uranium and plutonium carbides in the visible-near-infrared range

NASA Astrophysics Data System (ADS)

Fisenko, Anatoliy I.; Lemberg, Vladimir F.

2016-09-01

The knowledge of thermal radiative and thermodynamic properties of uranium and plutonium carbides under extreme conditions is essential for designing a new metallic fuel materials for next generation of a nuclear reactor. The present work is devoted to the study of the thermal radiative and thermodynamic properties of liquid and solid uranium and plutonium carbides at their melting/freezing temperatures. The Stefan-Boltzmann law, total energy density, number density of photons, Helmholtz free energy density, internal energy density, enthalpy density, entropy density, heat capacity at constant volume, pressure, and normal total emissivity are calculated using experimental data for the frequency dependence of the normal spectral emissivity of liquid and solid uranium and plutonium carbides in the visible-near infrared range. It is shown that the thermal radiative and thermodynamic functions of uranium carbide have a slight difference during liquid-to-solid transition. Unlike UC, such a difference between these functions have not been established for plutonium carbide. The calculated values for the normal total emissivity of uranium and plutonium carbides at their melting temperatures is in good agreement with experimental data. The obtained results allow to calculate the thermal radiative and thermodynamic properties of liquid and solid uranium and plutonium carbides for any size of samples. Based on the model of Hagen-Rubens and the Wiedemann-Franz law, a new method to determine the thermal conductivity of metals and carbides at the melting points is proposed.

Petroleum geology of Cook Inlet basin - an exploration model

USGS Publications Warehouse

Magoon, L.B.; Claypool, G.E.

1981-01-01

Oil exploration commenced onshore adjacent to lower Cook Inlet on the Iniskin Peninsula in 1900, shifted with considerable success to upper Cook Inlet from 1957 through 1965, then returned to lower Cook Inlet in 1977 with the COST well and Federal OCS sale. Lower Cook Inlet COST No. 1 well, drilled to a total depth of 3,775.6 m, penetrated basinwide unconformities at the tops of Upper Cretaceous, Lower Cretaceous, and Upper Jurassic strata at 797.1, 1,540.8, and 2,112.3 m, respectively. Sandstone of potential reservoir quality is present in the Cretaceous and lower Tertiary rocks. All siltstones and shales analyzed are low (0 to 0.5 wt. %) in oil-prone organic matter, and only coals are high in humic organic matter. At total depth, vitrinite readings reached a maximum ave age reflectance of 0.65. Several indications of hydrocarbons were present. Oil analyses suggest that oils from the major fields of the Cook Inlet region, most of which produce from the Tertiary Hemlock Conglomerate, have a common source. More detailed work on stable carbon isotope ratios and the distribution of gasoline-range and heavy (C12+) hydrocarbons confirms this genetic relation among the major fields. In addition, oils from Jurassic rocks under the Iniskin Peninsula and from the Hemlock Conglomerate at the southwestern tip of the Kenai lowland are members of the same or a very similar oil family. The Middle Jurassic strata of the Iniskin Peninsula are moderately rich in organic carbon (0.5 to 1.5 wt. %) and yield shows of oil and of gas in wells and in surface seeps. Extractable hydrocarbons from this strata are similar in chemi al and isotopic composition to the Cook Inlet oils. Organic matter in Cretaceous and Tertiary rocks is thermally immature in all wells analyzed. Oil reservoirs in the major producing fields are of Tertiary age and unconformably overlie Jurassic rocks; the pre-Tertiary unconformity may be significant in exploration for new oil reserves. The unconformable relation between reservoir rocks and likely Middle Jurassic source rocks also implies a delay in the generation and expulsion of oil from Jurassic until late Tertiary when localized basin subsidence and thick sedimentary fill brought older, deeper rocks to the temperature required for petroleum generation. Reservoir porosities, crude oil properties, the type of oil field traps, and the tectonic framework of the oil fields on the west flank of the basin provide evidence used to reconstruct an oil migration route. The route is inferred to commence deep in the truncated Middle Jur ssic rocks and pass through the porous West Foreland Formation in the McArthur River field area to a stratigraphic trap in the Oligocene Hemlock Conglomerate and the Oligocene part of the Tyonek Formation at the end of Miocene time. Pliocene deformation shut off this route and created localized structural traps, into which the oil moved by secondary migration to form the Middle Ground Shoal, McArthur River, and Trading Bay oil fields. Oil generation continued into the Pliocene, but this higher API gravity oil migrated along a different route to the Granite Point field.

Influence of microwaves on the leaching kinetics of uraninite from a low grade ore in dilute sulfuric acid.

PubMed

Madakkaruppan, V; Pius, Anitha; T, Sreenivas; Giri, Nitai; Sarbajna, Chanchal

2016-08-05

This paper describes a study on microwave assisted leaching of uranium from a low-grade ore of Indian origin. The host rock for uranium mineralization is chlorite-biotite-muscovite-quartzo-feldspathic schist. The dominant presence of siliceous minerals determined leaching of uranium values in sulfuric acid medium under oxidizing conditions. Process parametric studies like the effect of sulfuric acid concentration (0.12-0.50M), redox potential (400-500mV), particle size (600-300μm) and temperature (35°-95°C) indicated that microwave assisted leaching is more efficient in terms of overall uranium dissolution, kinetics and provide relatively less impurities (Si, Al, Mg and Fe) in the leach liquor compared to conventional conductive leaching. The kinetics of leaching followed shrinking core model with product layer diffusion as controlling mechanism. Copyright © 2016 Elsevier B.V. All rights reserved.

Carbothermic Synthesis of 820 m UN Kernels: Literature Review, Thermodynamics, Analysis, and Related Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lindemer, Terrence; Voit, Stewart L; Silva, Chinthaka M

2014-01-01

The U.S. Department of Energy is considering a new nuclear fuel that would be less susceptible to ruptures during a loss-of-coolant accident. The fuel would consist of tristructural isotropic coated particles with large, dense uranium nitride (UN) kernels. This effort explores many factors involved in using gel-derived uranium oxide-carbon microspheres to make large UN kernels. Analysis of recent studies with sufficient experimental details is provided. Extensive thermodynamic calculations are used to predict carbon monoxide and other pressures for several different reactions that may be involved in conversion of uranium oxides and carbides to UN. Experimentally, the method for making themore » gel-derived microspheres is described. These were used in a microbalance with an attached mass spectrometer to determine details of carbothermic conversion in argon, nitrogen, or vacuum. A quantitative model is derived from experiments for vacuum conversion to an uranium oxide-carbide kernel.« less

Efficient Removal of Uranium from Aqueous Solution by Reduced Graphene Oxide-Zn0.5Ni0.5Fe2O4 Ferrite-Polyaniline Nanocomposite

NASA Astrophysics Data System (ADS)

Tran, Dat Quang; Pham, Hung Thanh; Do, Hung Quoc

2017-06-01

Reduced graphene oxide-Zn0.5Ni0.5Fe2O4 ferrite-polyaniline nanocomposite (RGO-ZNF-PANI) was synthesized by a three-step method. The prepared samples were characterized by x-ray diffraction, Raman spectroscopy, scanning electron microscopy and vibrating sample magnetometer. In particular, we found that this material is capable of effectively removing uranium from an aquatic environment. This is confirmed by our experimental results using the method of inductively coupled plasma mass spectrometry. Adsorptive behaviour of uranium from an aqueous solution on the RGO-ZNF-PANI nanocomposite was examined as a function of pH, contact time, and equilibrium. Uranium concentration was carried out by batch techniques. The adsorption isotherm agrees well with the Langmuir model, having a maximum sorption capacity of 1885 mg/g, at pH 5 and 25°C.

The Model VI transmission fluorimeter for the determination of uranium

USGS Publications Warehouse

Kinser, Charles Alvin

1954-01-01

An improved transmission fluorimeter (Model VI) for use in the determination of uranium consists of a line-operated, low-voltage d-c supply, powering a small 3-watt ultraviolet lamp as a source of long wavelength ultraviolet radiation; a Model V phototube housing and. fluorimeter head containing the sample holder, shutter, and primary and secondary filters; an end-window multiplier phototube powered by a stable, commercially available high-voltage supply; and an electronic microammeter for measuring the output current from the photomultiplier tube. The instrument has excellent electrical stability and operates over a wide range of sensitivity. Its versatility makes it useful for both routine and research work.

Impact of the uranium (VI) speciation in mineralised urines on its extraction by calix[6]arene bearing hydroxamic groups used in chromatography columns.

PubMed

Baghdadi, S; Bouvier-Capely, C; Ritt, A; Peroux, A; Fevrier, L; Rebiere, F; Agarande, M; Cote, G

2015-11-01

Actinides determination in urine samples is part of the analyses performed to monitor internal contamination in case of an accident or a terrorist attack involving nuclear matter. Mineralisation is the first step of any of these analyses. It aims at reducing the sample volume and at destroying all organic compounds present. The mineralisation protocol is usually based on a wet ashing step, followed by actinides co-precipitation and a furnace ashing step, before redissolution and the quantification of the actinides by the appropriate techniques. Amongst the existing methods to perform the actinides co-precipitation, alkali-earth (typically calcium) precipitation is widely used. In the present work, the extraction of uranium(VI), plutonium(IV) and americium(III) from the redissolution solutions (called "mineralised urines") on calix[6]arene columns bearing hydroxamic groups was investigated as such an extraction is a necessary step before their determination by ICP-MS or alpha spectrometry. Difficulties were encountered in the transfer of uranium(VI) from raw to mineralised urines, with yield of transfer ranging between 0% and 85%, compared to about 90% for Pu and Am, depending on the starting raw urines. To understand the origin of such a difficulty, the speciation of uranium (VI) in mineralised urines was investigated by computer simulation using the MEDUSA software and the associated HYDRA database, compiled with recently published data. These calculations showed that the presence of phosphates in the "mineralised urines" leads to the formation of strong uranyl-phosphate complexes (such as UO2HPO4) which compete with the uranium (VI) extraction by the calix[6]arene bearing hydroxamic groups. The extraction constant of uranium (VI) by calix[6]arene bearing hydroxamic groups was determined in a 0.04 mol L(-1) sodium nitrate solution (logK=4.86±0.03) and implemented in an extraction model taking into account the speciation in the aqueous phase. This model allowed to simulate satisfactorily the experimental uranium extraction data and to support the preliminary conclusions about the role of the phosphates present in mineralised urines. These calculations also showed that the phosphate/calcium ratio is a key parameter as far as the efficiency of the uranium (VI) extraction by the calix[6]arene columns is concerned. It predicted that the addition of CaCl2 in mineralised urines would release uranium (VI) from phosphates by forming calcium (II)-phosphate complexes and thus facilitate the uranium (VI) extraction on calix[6]arene columns. These predictions were confirmed experimentally as the addition of 0.1 mol L(-1) CaCl2 to a mineralised urine containing naturally a high concentration of phosphate (typically 0.04 mol L(-1)) significantly increased the percentage of uranium (VI) extraction on the calix[6]arene columns. Copyright © 2015 Elsevier B.V. All rights reserved.

The effect of Si and Al concentrations on the removal of U(VI) in the alkaline conditions created by NH3 gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katsenovich, Yelena P.; Cardona, Claudia; Lapierre, Robert

2016-10-01

Remediation of uranium in the deep unsaturated zone is a challenging task, especially in the presence of oxygenated, high-carbonate alkalinity soil and pore water composition typical for arid and semi-arid environments of the western regions of the U.S. This study evaluates the effect of various pore water constituencies on changes of uranium concentrations in alkaline conditions, created in the presence of reactive gases such as NH3 to effectively mitigate uranium contamination in the vadose zone sediments. This contaminant is a potential source for groundwater pollution through slow infiltration of soluble and highly mobile uranium species towards the water table. Themore » objective of this research was to evaluate uranium sequestration efficiencies in the alkaline synthetic pore water solutions prepared in a broad range of Si, Al, and bicarbonate concentrations typically present in field systems of the western U.S. regions and identify solid uranium-bearing phases that result from ammonia gas treatment. In previous studies (Szecsody et al. 2012; Zhong et al. 2015), although uranium mobility was greatly decreased, solid phases could not be identified at the low uranium concentrations in field-contaminated sediments. The chemical composition of the synthetic pore water used in the experiments varied for silica (5–250 mM), Al3+ (2.8 or 5 mM), HCO3- (0–100 mM) and U(VI) (0.0021–0.0084 mM) in the solution mixture. Experiment results suggested that solutions with Si concentrations higher than 50 mM exhibited greater removal efficiencies of U(VI). Solutions with higher concentrations of bicarbonate also exhibited greater removal efficiencies for Si, Al, and U(VI). Overall, the silica polymerization reaction leading to the formation of Si gel correlated with the removal of U(VI), Si, and Al from the solution. If no Si polymerization was observed, there was no U removal from the supernatant solution. Speciation modeling indicated that the dominant uranium species in the presence of bicarbonate were anionic uranyl carbonate complexes (UO2(CO3)2-2 and UO2(CO3)3-4) and in the absence of bicarbonate in the solution, U(VI) major species appeared as uranyl-hydroxide (UO2(OH)3- and UO2(OH)4-2) species. The model also predicted the formation of uranium solid phases. Uranyl carbonates as rutherfordine [UO2CO3], cejkaite [Na4(UO2)(CO3)3] and hydrated uranyl silicate phases as Na-boltwoodite [Na(UO2)(SiO4)·1.5H2O] were anticipated for most of the synthetic pore water compositions amended from medium (2.9 mM) to high (100 mM) bicarbonate concentrations.« less

Rolling Process Modeling Report. Finite-Element Model Validation and Parametric Study on various Rolling Process parameters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soulami, Ayoub; Lavender, Curt A.; Paxton, Dean M.

2015-06-15

Pacific Northwest National Laboratory (PNNL) has been investigating manufacturing processes for the uranium-10% molybdenum alloy plate-type fuel for high-performance research reactors in the United States. This work supports the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization Reactor Conversion Program. This report documents modeling results of PNNL’s efforts to perform finite-element simulations to predict roll-separating forces for various rolling mill geometries for PNNL, Babcock & Wilcox Co., Y-12 National Security Complex, Los Alamos National Laboratory, and Idaho National Laboratory. The model developed and presented in a previous report has been subjected to further validationmore » study using new sets of experimental data generated from a rolling mill at PNNL. Simulation results of both hot rolling and cold rolling of uranium-10% molybdenum coupons have been compared with experimental results. The model was used to predict roll-separating forces at different temperatures and reductions for five rolling mills within the National Nuclear Security Administration Fuel Fabrication Capability project. This report also presents initial results of a finite-element model microstructure-based approach to study the surface roughness at the interface between zirconium and uranium-10% molybdenum.« less

Heat deposition analysis for the High Flux Isotope Reactor’s HEU and LEU core models

DOE PAGES

Davidson, Eva E.; Betzler, Benjamin R.; Chandler, David; ...

2017-08-01

The High Flux Isotope Reactor at Oak Ridge National Laboratory is an 85 MW th pressurized light-water-cooled and -moderated flux-trap type research reactor. The reactor is used to conduct numerous experiments, advancing various scientific and engineering disciplines. As part of an ongoing program sponsored by the US Department of Energy National Nuclear Security Administration Office of Material Management and Minimization, studies are being performed to assess the feasibility of converting the reactor’s highly enriched uranium fuel to low-enriched uranium fuel. To support this conversion project, reference models with representative experiment target loading and explicit fuel plate representation were developed andmore » benchmarked for both fuels to (1) allow for consistent comparison between designs for both fuel types and (2) assess the potential impact of low-enriched uranium conversion. These high-fidelity models were used to conduct heat deposition analyses at the beginning and end of the reactor cycle and are presented herein. This article (1) discusses the High Flux Isotope Reactor models developed to facilitate detailed heat deposition analyses of the reactor’s highly enriched and low-enriched uranium cores, (2) examines the computational approach for performing heat deposition analysis, which includes a discussion on the methodology for calculating the amount of energy released per fission, heating rates, power and volumetric heating rates, and (3) provides results calculated throughout various regions of the highly enriched and low-enriched uranium core at the beginning and end of the reactor cycle. These are the first detailed high-fidelity heat deposition analyses for the High Flux Isotope Reactor’s highly enriched and low-enriched core models with explicit fuel plate representation. Lastly, these analyses are used to compare heat distributions obtained for both fuel designs at the beginning and end of the reactor cycle, and they are essential for enabling comprehensive thermal hydraulics and safety analyses that require detailed estimates of the heat source within all of the reactor’s fuel element regions.« less

A physical description of fission product behavior fuels for advanced power reactors.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaganas, G.; Rest, J.; Nuclear Engineering Division

2007-10-18

The Global Nuclear Energy Partnership (GNEP) is considering a list of reactors and nuclear fuels as part of its chartered initiative. Because many of the candidate materials have not been explored experimentally under the conditions of interest, and in order to economize on program costs, analytical support in the form of combined first principle and mechanistic modeling is highly desirable. The present work is a compilation of mechanistic models developed in order to describe the fission product behavior of irradiated nuclear fuel. The mechanistic nature of the model development allows for the possibility of describing a range of nuclear fuelsmore » under varying operating conditions. Key sources include the FASTGRASS code with an application to UO{sub 2} power reactor fuel and the Dispersion Analysis Research Tool (DART ) with an application to uranium-silicide and uranium-molybdenum research reactor fuel. Described behavior mechanisms are divided into subdivisions treating fundamental materials processes under normal operation as well as the effect of transient heating conditions on these processes. Model topics discussed include intra- and intergranular gas-atom and bubble diffusion, bubble nucleation and growth, gas-atom re-solution, fuel swelling and ?scion gas release. In addition, the effect of an evolving microstructure on these processes (e.g., irradiation-induced recrystallization) is considered. The uranium-alloy fuel, U-xPu-Zr, is investigated and behavior mechanisms are proposed for swelling in the {alpha}-, intermediate- and {gamma}-uranium zones of this fuel. The work reviews the FASTGRASS kinetic/mechanistic description of volatile ?scion products and, separately, the basis for the DART calculation of bubble behavior in amorphous fuels. Development areas and applications for physical nuclear fuel models are identified.« less

A Classroom Demonstration of Thermohaline Circulation.

ERIC Educational Resources Information Center

Dudley, Walter C.

1984-01-01

Density-driven deep circulation is important in influencing geologic processes ranging from the dissolution of biogenic siliceous and calcareous sediments to the formation of erosional unconformities. A technique for dynamically demonstrating this process using an aquarium to enhance student understanding is described. (BC)

Linking Chaotic Advection with Subsurface Biogeochemical Processes

NASA Astrophysics Data System (ADS)

Mays, D. C.; Freedman, V. L.; White, S. K.; Fang, Y.; Neupauer, R.

2017-12-01

This work investigates the extent to which groundwater flow kinematics drive subsurface biogeochemical processes. In terms of groundwater flow kinematics, we consider chaotic advection, whose essential ingredient is stretching and folding of plumes. Chaotic advection is appealing within the context of groundwater remediation because it has been shown to optimize plume spreading in the laminar flows characteristic of aquifers. In terms of subsurface biogeochemical processes, we consider an existing model for microbially-mediated reduction of relatively mobile uranium(VI) to relatively immobile uranium(IV) following injection of acetate into a floodplain aquifer beneath a former uranium mill in Rifle, Colorado. This model has been implemented in the reactive transport code eSTOMP, the massively parallel version of STOMP (Subsurface Transport Over Multiple Phases). This presentation will report preliminary numerical simulations in which the hydraulic boundary conditions in the eSTOMP model are manipulated to simulate chaotic advection resulting from engineered injection and extraction of water through a manifold of wells surrounding the plume of injected acetate. This approach provides an avenue to simulate the impact of chaotic advection within the existing framework of the eSTOMP code.

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 3 2011-07-01 2011-07-01 false Uranium feed; natural uranium feed...) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The term uranium feed or natural uranium feed means natural uranium in the form of UF6 suitable for uranium...

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Uranium feed; natural uranium feed...) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The term uranium feed or natural uranium feed means natural uranium in the form of UF6 suitable for uranium...

Process for continuous production of metallic uranium and uranium alloys

DOEpatents

Hayden, H.W. Jr.; Horton, J.A.; Elliott, G.R.B.

1995-06-06

A method is described for forming metallic uranium, or a uranium alloy, from uranium oxide in a manner which substantially eliminates the formation of uranium-containing wastes. A source of uranium dioxide is first provided, for example, by reducing uranium trioxide (UO{sub 3}), or any other substantially stable uranium oxide, to form the uranium dioxide (UO{sub 2}). This uranium dioxide is then chlorinated to form uranium tetrachloride (UCl{sub 4}), and the uranium tetrachloride is then reduced to metallic uranium by reacting the uranium chloride with a metal which will form the chloride of the metal. This last step may be carried out in the presence of another metal capable of forming one or more alloys with metallic uranium to thereby lower the melting point of the reduced uranium product. The metal chloride formed during the uranium tetrachloride reduction step may then be reduced in an electrolysis cell to recover and recycle the metal back to the uranium tetrachloride reduction operation and the chlorine gas back to the uranium dioxide chlorination operation. 4 figs.

Process for continuous production of metallic uranium and uranium alloys

DOEpatents

Hayden, Jr., Howard W.; Horton, James A.; Elliott, Guy R. B.

1995-01-01

A method is described for forming metallic uranium, or a uranium alloy, from uranium oxide in a manner which substantially eliminates the formation of uranium-containing wastes. A source of uranium dioxide is first provided, for example, by reducing uranium trioxide (UO.sub.3), or any other substantially stable uranium oxide, to form the uranium dioxide (UO.sub.2). This uranium dioxide is then chlorinated to form uranium tetrachloride (UCl.sub.4), and the uranium tetrachloride is then reduced to metallic uranium by reacting the uranium chloride with a metal which will form the chloride of the metal. This last step may be carried out in the presence of another metal capable of forming one or more alloys with metallic uranium to thereby lower the melting point of the reduced uranium product. The metal chloride formed during the uranium tetrachloride reduction step may then be reduced in an electrolysis cell to recover and recycle the metal back to the uranium tetrachloride reduction operation and the chlorine gas back to the uranium dioxide chlorination operation.

Modeling spallation reactions in tungsten and uranium targets with the Geant4 toolkit

NASA Astrophysics Data System (ADS)

Malyshkin, Yury; Pshenichnov, Igor; Mishustin, Igor; Greiner, Walter

2012-02-01

We study primary and secondary reactions induced by 600 MeV proton beams in monolithic cylindrical targets made of natural tungsten and uranium by using Monte Carlo simulations with the Geant4 toolkit [1-3]. Bertini intranuclear cascade model, Binary cascade model and IntraNuclear Cascade Liège (INCL) with ABLA model [4] were used as calculational options to describe nuclear reactions. Fission cross sections, neutron multiplicity and mass distributions of fragments for 238U fission induced by 25.6 and 62.9 MeV protons are calculated and compared to recent experimental data [5]. Time distributions of neutron leakage from the targets and heat depositions are calculated. This project is supported by Siemens Corporate Technology.

From rum jungle to Wismut-reducing the environmental impact of uranium mining and milling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zuk, W.M.; Jeffree, R.A.; Levins, D.M.

1994-12-31

Australia has a long history of uranium mining. In the early days, little attention was given to environmental matters and considerable pollution occurred. Ansto has been involved in rehabilitation of a number of the early uranium mining sites, from Rum Jungle in Australia`s Northern Territory to Wismut in Germany, and is working with current producers to minimise the environmental impact of their operations. Ansto`s expertise is extensive and includes, inter alia, amelioration of acid mine drainage, radon measurement and control, treatment of mill wastes, management of tailings, monitoring of seepage plumes, mathematical modelling of pollutant transport and biological impacts inmore » a tropical environment.« less

Paragenesis and Geochronology of the Nopal I Uranium Deposit, Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. Fayek; M. Ren

2007-02-14

Uranium deposits can, by analogy, provide important information on the long-term performance of radioactive waste forms and radioactive waste repositories. Their complex mineralogy and variable elemental and isotopic compositions can provide important information, provided that analyses are obtained on the scale of several micrometers. Here, we present a structural model of the Nopal I deposit as well as petrography at the nanoscale coupled with preliminary U-Th-Pb ages and O isotopic compositions of uranium-rich minerals obtained by Secondary Ion Mass Spectrometry (SIMS). This multi-technique approach promises to provide ''natural system'' data on the corrosion rate of uraninite, the natural analogue ofmore » spent nuclear fuel.« less

Mathematical simulation of the amplification of 1790-nm laser radiation in a nuclear-excited He - Ar plasma containing nanoclusters of uranium compounds

NASA Astrophysics Data System (ADS)

Kosarev, V. A.; Kuznetsova, E. E.

2014-02-01

The possibility of applying dusty active media in nuclearpumped lasers has been considered. The amplification of 1790-nm radiation in a nuclear-excited dusty He - Ar plasma is studied by mathematical simulation. The influence of nanoclusters on the component composition of the medium and the kinetics of the processes occurring in it is analysed using a specially developed kinetic model, including 72 components and more than 400 reactions. An analysis of the results indicates that amplification can in principle be implemented in an active laser He - Ar medium containing 10-nm nanoclusters of metallic uranium and uranium dioxide.

Supervised Machine Learning for Regionalization of Environmental Data: Distribution of Uranium in Groundwater in Ukraine

NASA Astrophysics Data System (ADS)

Govorov, Michael; Gienko, Gennady; Putrenko, Viktor

2018-05-01

In this paper, several supervised machine learning algorithms were explored to define homogeneous regions of con-centration of uranium in surface waters in Ukraine using multiple environmental parameters. The previous study was focused on finding the primary environmental parameters related to uranium in ground waters using several methods of spatial statistics and unsupervised classification. At this step, we refined the regionalization using Artifi-cial Neural Networks (ANN) techniques including Multilayer Perceptron (MLP), Radial Basis Function (RBF), and Convolutional Neural Network (CNN). The study is focused on building local ANN models which may significantly improve the prediction results of machine learning algorithms by taking into considerations non-stationarity and autocorrelation in spatial data.

Rate Theory Modeling and Simulations of Silicide Fuel at LWR Conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miao, Yinbin; Ye, Bei; Mei, Zhigang

Uranium silicide (U 3Si 2) fuel has higher thermal conductivity and higher uranium density, making it a promising candidate for the accident-tolerant fuel (ATF) used in light water reactors (LWRs). However, previous studies on the fuel performance of U 3Si 2, including both experimental and computational approaches, have been focusing on the irradiation conditions in research reactors, which usually involve low operation temperatures and high fuel burnups. Thus, it is important to examine the fuel performance of U 3Si 2 at typical LWR conditions so as to evaluate the feasibility of replacing conventional uranium dioxide fuel with this silicide fuelmore » material. As in-reactor irradiation experiments involve significant time and financial cost, it is appropriate to utilize modeling tools to estimate the behavior of U 3Si 2 in LWRs based on all those available research reactor experimental references and state-of-the-art density functional theory (DFT) calculation capabilities at the early development stage. Hence, in this report, a comprehensive investigation of the fission gas swelling behavior of U 3Si 2 at LWR conditions is introduced. The modeling efforts mentioned in this report was based on the rate theory (RT) model of fission gas bubble evolution that has been successfully applied for a variety of fuel materials at devious reactor conditions. Both existing experimental data and DFT-calculated results were used for the optimization of the parameters adopted by the RT model. Meanwhile, the fuel-cladding interaction was captured by the coupling of the RT model with simplified mechanical correlations. Therefore, the swelling behavior of U 3Si 2 fuel and its consequent interaction with cladding in LWRs was predicted by the rate theory modeling, providing valuable information for the development of U 3Si 2 fuel as an accident-tolerant alternative for uranium dioxide.« less

The Nopal 1 Uranium Deposit: an Overview

NASA Astrophysics Data System (ADS)

Calas, G.; Allard, T.; Galoisy, L.

2007-05-01

The Nopal 1 natural analogue is located in the Pena Blanca uranium district, about 50 kms north of Chihuahua City, Mexico. The deposit is hosted in tertiary ignimbritic ash-flow tuffs, dated at 44 Ma (Nopal and Colorados formations), and overlying the Pozos conglomerate formation and a sequence of Cretaceous carbonate rocks. The deposit is exposed at the ground surface and consists of a near vertical zone extending over about 100 m with a diameter of 40 m. An interesting characteristic is that the primary mineralization has been exposed above the water table, as a result of the uplift of the Sierra Pena Blanca, and subsequently oxidized with a remobilization of hexavalent uranium. The primary mineralization has been explained by various genetic models. It is associated to an extensive hydrothermal alteration of the volcanic tuffs, locally associated to pyrite and preserved by an intense silicification. Several kaolinite parageneses occur in fissure fillings and feldspar pseudomorphs, within the mineralized breccia pipe and the barren surrounding rhyolitic tuffs. Smectites are mainly developed in the underlying weakly welded tuffs. Several radiation-induced defect centers have been found in these kaolinites providing a unique picture of the dynamics of uranium mobilization (see Allard et al., this session). Another evidence of this mobilization is given by the spectroscopy of uranium-bearing opals, which show characteristic fluorescence spectra of uranyl groups sorbed at the surface of silica. By comparison with the other uranium deposits of the Sierra Pena Blanca and the nearby Sierra de Gomez, the Nopal 1 deposit is original, as it is one of the few deposits hving retained a reduced uranium mineralization.

Effects of hydrated lime on radionuclides stabilization of Hanford tank residual waste.

PubMed

Wang, Guohui; Um, Wooyong; Cantrell, Kirk J; Snyder, Michelle M V; Bowden, Mark E; Triplett, Mark B; Buck, Edgar C

2017-10-01

Chemical stabilization of tank residual waste is part of a Hanford Site tank closure strategy to reduce overall risk levels to human health and the environment. In this study, a set of column leaching experiments using tank C-104 residual waste were conducted to evaluate the leachability of uranium (U) and technetium (Tc) where grout and hydrated lime were applied as chemical stabilizing agents. The experiments were designed to simulate future scenarios where meteoric water infiltrates through the vadose zones into the interior of the tank filled with layers of grout or hydrated lime, and then contacts the residual waste. Effluent concentrations of U and Tc were monitored and compared among three different packing columns (waste only, waste + grout, and waste + grout + hydrated lime). Geochemical modeling of the effluent compositions was conducted to determine saturation indices of uranium solid phases that could control the solubility of uranium. The results indicate that addition of hydrated lime strongly stabilized the uranium through transforming uranium to a highly insoluble calcium uranate (CaUO 4 ) or similar phase, whereas no significant stabilization effect of grout or hydrated lime was observed on Tc leachability. The result implies that hydrated lime could be a great candidate for stabilizing Hanford tank residual wastes where uranium is one of the main concerns. Published by Elsevier Ltd.

Metallogenic evolution of uranium deposits in the Middle East and North Africa deposits

NASA Astrophysics Data System (ADS)

Howari, Fares; Goodell, Philip; Salman, Abdulaty

2016-02-01

This paper is briefly involved in classification and distributions of the Middle East and North Africa (MENA) uranium deposits. The study of these mineral systems can significantly contribute to our further understanding of the metallogeny of known and poorly explored deposits. This provides contribution to, and further enhancement of, current classifications and metallogenic models of uranium systems, allowing researchers to emphasize on unknown or poorly studied mineral systems found in MENA. The present study identified eight metallogenic types of uranium associated with: 1) the Archean rocks and intra-cratonic basins, 2) the Pan-African granites and rhyolites which are characterized by igneous activity, 3) Phanerozoic (Paleozoic) clastics, these deposits are the sedimentological response to Pan African magmatism, 4) Mesozoic (basal) clastics type e.g. Nubia sandstones which are characterized by uranium minerals, 5) regional sedimentary phosphate deposits which are categorized as geosynclinal, or continental margin deposits, on the shelf of the Tethys Ocean, 6) Cenozoic Intracratonic Felsic Magmatism of the Tibesti and Hoggar, and the sandstone U deposits of adjoining Niger. These are similar to the Pan-African magmatism metallogenic, 7) Calcretes, and 8) Resistate minerals which are often enriched in rare earth elements, sometimes including uranium. They are thus sometimes considered as U resources but poorly explored in the MENA region. These metallogenic types are described and discussed in the current paper.

ZPR-3 Assembly 11 : A cylindrical sssembly of highly enriched uranium and depleted uranium with an average {sup 235}U enrichment of 12 atom % and a depleted uranium reflector.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lell, R. M.; McKnight, R. D.; Tsiboulia, A.

2010-09-30

Over a period of 30 years, more than a hundred Zero Power Reactor (ZPR) critical assemblies were constructed at Argonne National Laboratory. The ZPR facilities, ZPR-3, ZPR-6, ZPR-9 and ZPPR, were all fast critical assembly facilities. The ZPR critical assemblies were constructed to support fast reactor development, but data from some of these assemblies are also well suited for nuclear data validation and to form the basis for criticality safety benchmarks. A number of the Argonne ZPR/ZPPR critical assemblies have been evaluated as ICSBEP and IRPhEP benchmarks. Of the three classes of ZPR assemblies, engineering mockups, engineering benchmarks and physicsmore » benchmarks, the last group tends to be most useful for criticality safety. Because physics benchmarks were designed to test fast reactor physics data and methods, they were as simple as possible in geometry and composition. The principal fissile species was {sup 235}U or {sup 239}Pu. Fuel enrichments ranged from 9% to 95%. Often there were only one or two main core diluent materials, such as aluminum, graphite, iron, sodium or stainless steel. The cores were reflected (and insulated from room return effects) by one or two layers of materials such as depleted uranium, lead or stainless steel. Despite their more complex nature, a small number of assemblies from the other two classes would make useful criticality safety benchmarks because they have features related to criticality safety issues, such as reflection by soil-like material. ZPR-3 Assembly 11 (ZPR-3/11) was designed as a fast reactor physics benchmark experiment with an average core {sup 235}U enrichment of approximately 12 at.% and a depleted uranium reflector. Approximately 79.7% of the total fissions in this assembly occur above 100 keV, approximately 20.3% occur below 100 keV, and essentially none below 0.625 eV - thus the classification as a 'fast' assembly. This assembly is Fast Reactor Benchmark No. 8 in the Cross Section Evaluation Working Group (CSEWG) Benchmark Specificationsa and has historically been used as a data validation benchmark assembly. Loading of ZPR-3 Assembly 11 began in early January 1958, and the Assembly 11 program ended in late January 1958. The core consisted of highly enriched uranium (HEU) plates and depleted uranium plates loaded into stainless steel drawers, which were inserted into the central square stainless steel tubes of a 31 x 31 matrix on a split table machine. The core unit cell consisted of two columns of 0.125 in.-wide (3.175 mm) HEU plates, six columns of 0.125 in.-wide (3.175 mm) depleted uranium plates and one column of 1.0 in.-wide (25.4 mm) depleted uranium plates. The length of each column was 10 in. (254.0 mm) in each half of the core. The axial blanket consisted of 12 in. (304.8 mm) of depleted uranium behind the core. The thickness of the depleted uranium radial blanket was approximately 14 in. (355.6 mm), and the length of the radial blanket in each half of the matrix was 22 in. (558.8 mm). The assembly geometry approximated a right circular cylinder as closely as the square matrix tubes allowed. According to the logbook and loading records for ZPR-3/11, the reference critical configuration was loading 10 which was critical on January 21, 1958. Subsequent loadings were very similar but less clean for criticality because there were modifications made to accommodate reactor physics measurements other than criticality. Accordingly, ZPR-3/11 loading 10 was selected as the only configuration for this benchmark. As documented below, it was determined to be acceptable as a criticality safety benchmark experiment. A very accurate transformation to a simplified model is needed to make any ZPR assembly a practical criticality-safety benchmark. There is simply too much geometric detail in an exact (as-built) model of a ZPR assembly, even a clean core such as ZPR-3/11 loading 10. The transformation must reduce the detail to a practical level without masking any of the important features of the critical experiment. And it must do this without increasing the total uncertainty far beyond that of the original experiment. Such a transformation is described in Section 3. It was obtained using a pair of continuous-energy Monte Carlo calculations. First, the critical configuration was modeled in full detail - every plate, drawer, matrix tube, and air gap was modeled explicitly. Then the regionwise compositions and volumes from the detailed as-built model were used to construct a homogeneous, two-dimensional (RZ) model of ZPR-3/11 that conserved the mass of each nuclide and volume of each region. The simple cylindrical model is the criticality-safety benchmark model. The difference in the calculated k{sub eff} values between the as-built three-dimensional model and the homogeneous two-dimensional benchmark model was used to adjust the measured excess reactivity of ZPR-3/11 loading 10 to obtain the k{sub eff} for the benchmark model.« less

230Th-234U Model-Ages of Some Uranium Standard Reference Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, R W; Gaffney, A M; Kristo, M J

The 'age' of a sample of uranium is an important aspect of a nuclear forensic investigation and of the attribution of the material to its source. To the extent that the sample obeys the standard rules of radiochronometry, then the production ages of even very recent material can be determined using the {sup 230}Th-{sup 234}U chronometer. These standard rules may be summarized as (a) the daughter/parent ratio at time=zero must be known, and (b) there has been no daughter/parent fractionation since production. For most samples of uranium, the 'ages' determined using this chronometer are semantically 'model-ages' because (a) some assumptionmore » of the initial {sup 230}Th content in the sample is required and (b) closed-system behavior is assumed. The uranium standard reference materials originally prepared and distributed by the former US National Bureau of Standards and now distributed by New Brunswick Laboratory as certified reference materials (NBS SRM = NBL CRM) are good candidates for samples where both rules are met. The U isotopic standards have known purification and production dates, and closed-system behavior in the solid form (U{sub 3}O{sub 8}) may be assumed with confidence. We present here {sup 230}Th-{sup 234}U model-ages for several of these standards, determined by isotope dilution mass spectrometry using a multicollector ICP-MS, and compare these ages with their known production history.« less

Microbial Reduction of Fe(III) and U(VI) in Aquifers: Simulations Exploring Coupled Effects of Heterogeneity and Fe(II) Sorption

NASA Astrophysics Data System (ADS)

Scheibe, T. D.; Fang, Y.; Roden, E. E.; Brooks, S. C.; Chien, Y.; Murray, C. J.

2004-05-01

Uranium is a significant groundwater contaminant at many former mining and processing sites. In its oxidized state, U(VI) is soluble and mobile, although strongly retarded by sorption to natural iron oxide surfaces. It has been demonstrated that commonly occurring subsurface microorganisms can reduce uranium and other metals when provided sufficient carbon as an electron donor. Reduced U(IV) precipitates as a solid phase; therefore biostimulation provides a potential strategy for in situ removal from contaminated groundwater. However, these biogeochemical reactions occur in the context of a complex heterogeneous environment in which flow and transport dynamics and abiotic reactions can have significant impacts. We have constructed a high-resolution numerical model of groundwater flow and multicomponent reactive transport that incorporates heterogeneity in hydraulic conductivity and initial Fe(III) distribution, microbial growth and transport dynamics, and effects of sorption or precipitation of biogenic Fe(II) on availability of Fe(III) as an electron acceptor. The biogeochemical reaction models and their parameters are based on laboratory experiments; the heterogeneous field-scale property distributions are based on interpretations of geophysical and other observations at a highly characterized field site. The model is being run in Monte Carlo mode to examine the controls that these factors exert on 1) the initial distribution of sorbed uranium in an oxic environment and 2) the reduction and immobilization of uranium upon introduction of a soluble electron donor.

Supercritical Fluid Extraction of Toxic Heavy Metals and Uranium from Acidic Solutions with Sulfur-Containing Organophosphorus Reagents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Yuehe; Liu, Chongxuan; Wu, Hong

2003-03-02

The feasibility of using sulfur-containing organophosphorus reagents for the chelation-supercritical fluid extraction (SFE) of toxic heavy metals and uranium from acidic media was investigated. The SFE experiments were conducted in a specially-designed flow-through liquid extractor. Effective extraction of the metal ions from various acidic media was demonstrated. The effect of ligand concentration in supercritical CO{sub 2} on the kinetics of metal extraction was studied. A simplified model is used to describe the extraction kinetics and the good agreement of experimental data with the equilibrium-based model is achieved.

Method for converting uranium oxides to uranium metal

DOEpatents

Duerksen, Walter K.

1988-01-01

A process is described for converting scrap and waste uranium oxide to uranium metal. The uranium oxide is sequentially reduced with a suitable reducing agent to a mixture of uranium metal and oxide products. The uranium metal is then converted to uranium hydride and the uranium hydride-containing mixture is then cooled to a temperature less than -100.degree. C. in an inert liquid which renders the uranium hydride ferromagnetic. The uranium hydride is then magnetically separated from the cooled mixture. The separated uranium hydride is readily converted to uranium metal by heating in an inert atmosphere. This process is environmentally acceptable and eliminates the use of hydrogen fluoride as well as the explosive conditions encountered in the previously employed bomb-reduction processes utilized for converting uranium oxides to uranium metal.

Modeling the UO2 ex-AUC pellet process and predicting the fuel rod temperature distribution under steady-state operating condition

NASA Astrophysics Data System (ADS)

Hung, Nguyen Trong; Thuan, Le Ba; Thanh, Tran Chi; Nhuan, Hoang; Khoai, Do Van; Tung, Nguyen Van; Lee, Jin-Young; Jyothi, Rajesh Kumar

2018-06-01

Modeling uranium dioxide pellet process from ammonium uranyl carbonate - derived uranium dioxide powder (UO2 ex-AUC powder) and predicting fuel rod temperature distribution were reported in the paper. Response surface methodology (RSM) and FRAPCON-4.0 code were used to model the process and to predict the fuel rod temperature under steady-state operating condition. Fuel rod design of AP-1000 designed by Westinghouse Electric Corporation, in these the pellet fabrication parameters are from the study, were input data for the code. The predictive data were suggested the relationship between the fabrication parameters of UO2 pellets and their temperature image in nuclear reactor.

A palynostratigraphic approach to the SW Anatolian molasse basin: Kale-Tavas molasse and Denizli molasse

NASA Astrophysics Data System (ADS)

Akgün, Funda; Sözbilir, Hasan

The study, explains stratigraphy of the Oligo-Miocene molasse around the Denizli province (SW Anatolia), based on the palynology which is also supported by the detailed mapping and correlation of the measured sections from the coal-bearing sequences of the molasse deposits. For this purpose, two huge depressions named as the Kale-Tavas molasse and Denizli molasse basins were examined. The Kale-Tavas molasse deposits has a basal unconformity with the underlying pre-Oligocene basement and begins with the Chattian Karadere and Mortuma formations which are covered unconformably by the Aquitanian Yenidere formation. An angular unconformity between the Chattian and the Burdigalian is only observed in the middle part of the basin, around Kale. In the Tavas section, the Aquitanian and the Burdigalian are absent. The Denizli molasse is characterized by Chattian-Aquitanian sequence consisting of distinctive sedimentary facies, alluvial fan and deltaic-shallow marine deposits with carbonate patch reefs. Palynostratigraphic studies, which have given the Chattian age, have been carried out from the coal lenses of alluvial fan and delta plain deposits. In addition to the palynological determinations, coral and foraminiferal content of the carbonate patch reefs which rest conformably on the coal-bearing sequences have yielded the Chattian-Aquitanian age. Two different palynomorph associations have been determined from the molasse deposits. The first palynomorph association which is established in the samples from the Sağdere and Mortuma formations, corresponds to the Chattian age, whilst the second is of the Aquitanian age. The Late Oligocene-Early Miocene which is claimed as the time of N-S-extensional tectonics in western Turkey, is related to the depositional time of the molasse sequences in the study area. Thus, the molasse is older than the basal deposits of the Gediz and Büyük Menderes grabens.

Lithofacies variation across the Mammoth Cave-Pope Megagroup boundary -- a sequence stratigraphic approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDonald, T.A.; Tabor, E.; Marzolf, J.E.

1994-04-01

Regional stratigraphic relations in southern Illinois suggest a major unconformity near the top of the St. Genevieve Limestone. Large exposures below the unconformity within the Anna quarries display a retrogradational parasequence-stacking pattern. Eight to 12 m-thick parasequences comprise thinning-upward marine bioclastic wackestone overlain by oolitic and bioclastic thickening-upward eolian( ) grainstone. An eolian origin for the bioclastic grainstones is supported by large scale cross stratification (0.5 to 2 m-thick sets), reworked character of rounded, coated bioclasts, and preserved duneforms. At the quarries, the unconformity is directly overlain by mudstones and sandstones. Thinning-upward mudstones interbedded with very thin (1 to 3more » cm thick) intraclastic packstone tempestites crop out in a roadcut about 500 m NE of the quarries. Small-scale ripples and absence of trace fossils in lower mudstone units suggest an estuarine or lagoonal, brackish-waver environment. The trace fossil Conostichus and horizontal burrows appear abruptly in the upper, thin mudstone units. Highly bioturbated green and red shales overlying a 1 to 4 m-thick covered interval in a roadcut 610 m farther north are interbedded with tidally deposited, medium- to coarse-grained, bioclastic grainstones. The shale-draped, medium cross-bedded grainstones document ten or more tidal bundles. The cross-bedded grainstone is overlain by wavy- to flaser-bedded very fine-grained sandstone suggestive of sand flat origin. These sandstones are overlain by the Aux Vases Sandstone. Numerous low-angle bounding surfaces within the Aux Vases enclose low-angle, wedge-planar cross-bedding. A single irregular surface coated by a few centimeters of poorly sorted unstratified sandstone defines a ravinement surface near the base of the Aux Vases Sandstone.« less

Recent advances in the cretaceous stratigraphy of Korea

NASA Astrophysics Data System (ADS)

Chang, Ki-Hong; Suzuki, Kazuhiro; Park, Sun-Ok; Ishida, Keisuke; Uno, Koji

2003-06-01

A subrounded, accidental, zircon grain from a rhyolite sample of the Oknyobong Formation has shown an U-Pb CHIME isochron age, 187 Ma, implying its derivation from a Jurassic felsic igneous rock. Such a lower limit of the geologic age of the Oknyobong Formation, combined with its pre-Kyongsang upper limit, constrains that the Oknyobong Formation belongs to the Jasong Synthem (Late Jurassic-early Early Cretaceous) typified in North Korea. The Jaeryonggang Movement terminated the deposition of the Jasong Synthem and caused a shift of the depocenter from North Korea to the Kyongsang Basin, Southeast Korea. The Cretaceous-Paleocene Kyongsang Supergroup of the Kyongsang Basin is the stratotype of the Kyongsang Synthem, an unconformity-bounded unit in the Korean Peninsula. The unconformity at the base of the Yuchon Volcanic Group is a local expression of the interregionally recognizable mid-Albian tectonism; it subdivides the Kyongsang Synthem into the Lower Kyongsang Subsynthem (Barremian-Early Albian) and the Upper Kyongsang Subsynthem (Late Albian-Paleocene). The latter is unconformably overlain by Eocene and younger strata. The Late Permian to Early Jurassic radiolarian fossils from the chert pebbles of the Kumidong and the Kisadong conglomerates of the Aptian-Early Albian Hayang Group of the Kyongsang Basin are equivalent with those of the cherts that constitute the Jurassic accretionary prisms in Japan, the provenance of the chert pebbles in the Kyongsang Basin. Bimodal volcanisms throughout the history of the Kyongsang Basin is exemplified by the felsic Kusandong Tuff erupted abruptly and briefly in the Late Aptian when semi-coeval volcanisms were of intermediate and mafic compositions. The mean paleomagnetic direction shown by the Kusandong Tuff is in good agreement with the Early Cretaceous directions known from North China, South China and Siberia Blocks.

Paleogeothermal record of the Emeishan mantle plume: evidences from borehole Ro data in the Sichuan basin, SW China

NASA Astrophysics Data System (ADS)

Hu, S.

2013-12-01

The Emeishan basalt province located in the southwest of China is widely accepted to be a result of the eruption of a mantle plume at the time of middle-late Permian. If it was a mantle plume, the ambient sedimentary rocks must be heated up during the development of the mantle plume and this thermal effect must be recorded by some geothermometers in the country rocks. The vitrinite reflectance (Ro) data as a maximum paleotemperature recorder from boreholes in Sichuan basin was employed to expose the thermal regime related to the proposed Emeishan mantle plume. The Ro profiles from boreholes which drilled close to the Emeishan basalts shows a ';dog-leg' (break) style at the unconformity between the middle and the upper Permian, and the Ro profiles in the lower subsection (pre-middle Permian) shows a significantly higher slopes (gradients) than those in the upper subsection. In contrast, those Ro profiles from boreholes far away from the center of the basalt province have no break at the uncomformity. Based on the chemical kinetic model of Ro, the paleo-temperature gradients for the upper and the lower subsections in different boreholes, as well as the erosion at the unconformity between the middle and the upper Permian, were reconstructed to reveal the variations of the temperature gradients and erosion thickness with geological time and space. Both the thermal regime and the erosion thickness together with their spatial variation (structure) provide strong geothermal evidence for the existence of the Emeishan mantle plume in the middle-late Permian.

Paleocene to Middle Miocene planktic foraminifera of the southwestern Salisbury Embayment, Virginia and Maryland: biostratigraphy, allostratigraphy, and sequence stratigraphy

USGS Publications Warehouse

Poag, C.W.; Commeau, J.A.

1995-01-01

The Paleocene to Middle Miocene sedimentary fill of the southwestern Salisbury Embayment contains a fragmental depositional record, interrupted by numerous local diastems and regional unconformities. Using planktic foraminiferal biostratigraphy, 15 unconformity-bounded depositional units have been identified, assigned to six formations and seven alloformations previously recognized in the embayment. The units correlate with second- and third-order sequences of the Exxon sequence stratigraphy model, and include transgressive and highstand systems tracts. Alloformation, formation, and sequence boundaries are marked by abrupt, scoured, burrowed, erosional surfaces, which display lag deposits, biostratigraphic gaps, and intense reworking of microfossils above and below the boundaries.Paleocene deposits represent the upper parts of upper Pleocene Biochronozones P4 and P5, and rest uncomformably  on Cretaceous sedimentary beds of various ages (Maastrichtian to Albian). Lower Eocene deposits represent parts of Biochronozones P6 and P9. Middle Eocene strata represent mainly parts of Biochronozones P11, P12, and P14. Upper Eocene sediments include parts of Biochronozones P15, P16, and P17. Oligocene deposits encompass parts of Biochronozones. N4b to N7 undifferentiated, P21a, and, perhaps, N4a. Lower Miocene deposits encompass parts of Biochronozones N4b to N7 undifferentiated. Middle Miocene strata represent mainly parts of Biochronorones N8, N9, and N10.Nine plates of scanning electron micrographs illustrate the principal planktic foraminifera used to establish the biostratigraphic framework. Two new informal formine of Praeterenuitella praegemma Li, 1987, are introduced.

Molecular dynamics simulation of thermal transport in UO 2 containing uranium, oxygen, and fission-product defects

DOE PAGES

Liu, Xiang -Yang; Cooper, Michael William D.; McClellan, Kenneth James; ...

2016-10-25

Uranium dioxide (UO 2) is the most commonly used fuel in light-water nuclear reactors and thermal conductivity controls the removal of heat produced by fission, thereby governing fuel temperature during normal and accident conditions. The use of fuel performance codes by the industry to predict operational behavior is widespread. A primary source of uncertainty in these codes is thermal conductivity, and optimized fuel utilization may be possible if existing empirical models are replaced with models that incorporate explicit thermal-conductivity-degradation mechanisms during fuel burn up. This approach is able to represent the degradation of thermal conductivity due to each individual defectmore » type, rather than the overall burn-up measure typically used, which is not an accurate representation of the chemical or microstructure state of the fuel that actually governs thermal conductivity and other properties. To generate a mechanistic thermal conductivity model, molecular dynamics (MD) simulations of UO 2 thermal conductivity including representative uranium and oxygen defects and fission products are carried out. These calculations employ a standard Buckingham-type interatomic potential and a potential that combines the many-body embedded-atom-method potential with Morse-Buckingham pair potentials. Potential parameters for UO 2+x and ZrO 2 are developed for the latter potential. Physical insights from the resonant phonon-spin-scattering mechanism due to spins on the magnetic uranium ions are introduced into the treatment of the MD results, with the corresponding relaxation time derived from existing experimental data. High defect scattering is predicted for Xe atoms compared to that of La and Zr ions. Uranium defects reduce the thermal conductivity more than oxygen defects. For each defect and fission product, scattering parameters are derived for application in both a Callaway model and the corresponding high-temperature model typically used in fuel-performance codes. The model is validated by comparison to low-temperature experimental measurements on single-crystal hyperstoichiometric UO 2+x samples and high-temperature literature data. Furthermore, this work will enable more accurate fuel-performance simulations and will extend to new fuel types and operating conditions, all of which improve the fuel economics of nuclear energy and maintain high fuel reliability and safety.« less

Molecular dynamics simulation of thermal transport in UO 2 containing uranium, oxygen, and fission-product defects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Xiang -Yang; Cooper, Michael William D.; McClellan, Kenneth James

Uranium dioxide (UO 2) is the most commonly used fuel in light-water nuclear reactors and thermal conductivity controls the removal of heat produced by fission, thereby governing fuel temperature during normal and accident conditions. The use of fuel performance codes by the industry to predict operational behavior is widespread. A primary source of uncertainty in these codes is thermal conductivity, and optimized fuel utilization may be possible if existing empirical models are replaced with models that incorporate explicit thermal-conductivity-degradation mechanisms during fuel burn up. This approach is able to represent the degradation of thermal conductivity due to each individual defectmore » type, rather than the overall burn-up measure typically used, which is not an accurate representation of the chemical or microstructure state of the fuel that actually governs thermal conductivity and other properties. To generate a mechanistic thermal conductivity model, molecular dynamics (MD) simulations of UO 2 thermal conductivity including representative uranium and oxygen defects and fission products are carried out. These calculations employ a standard Buckingham-type interatomic potential and a potential that combines the many-body embedded-atom-method potential with Morse-Buckingham pair potentials. Potential parameters for UO 2+x and ZrO 2 are developed for the latter potential. Physical insights from the resonant phonon-spin-scattering mechanism due to spins on the magnetic uranium ions are introduced into the treatment of the MD results, with the corresponding relaxation time derived from existing experimental data. High defect scattering is predicted for Xe atoms compared to that of La and Zr ions. Uranium defects reduce the thermal conductivity more than oxygen defects. For each defect and fission product, scattering parameters are derived for application in both a Callaway model and the corresponding high-temperature model typically used in fuel-performance codes. The model is validated by comparison to low-temperature experimental measurements on single-crystal hyperstoichiometric UO 2+x samples and high-temperature literature data. Furthermore, this work will enable more accurate fuel-performance simulations and will extend to new fuel types and operating conditions, all of which improve the fuel economics of nuclear energy and maintain high fuel reliability and safety.« less

Uncertainty and variability in laboratory derived sorption parameters of sediments from a uranium in situ recovery site

NASA Astrophysics Data System (ADS)

Dangelmayr, Martin A.; Reimus, Paul W.; Johnson, Raymond H.; Clay, James T.; Stone, James J.

2018-06-01

This research assesses the ability of a GC SCM to simulate uranium transport under variable geochemical conditions typically encountered at uranium in-situ recovery (ISR) sites. Sediment was taken from a monitoring well at the SRH site at depths 192 and 193 m below ground and characterized by XRD, XRF, TOC, and BET. Duplicate column studies on the different sediment depths, were flushed with synthesized restoration waters at two different alkalinities (160 mg/l CaCO3 and 360 mg/l CaCO3) to study the effect of alkalinity on uranium mobility. Uranium breakthrough occurred 25% - 30% earlier in columns with 360 mg/l CaCO3 over columns fed with 160 mg/l CaCO3 influent water. A parameter estimation program (PEST) was coupled to PHREEQC to derive site densities from experimental data. Significant parameter fittings were produced for all models, demonstrating that the GC SCM approach can model the impact of carbonate on uranium in flow systems. Derived site densities for the two sediment depths were between 141 and 178 μmol-sites/kg-soil, demonstrating similar sorption capacities despite heterogeneity in sediment mineralogy. Model sensitivity to alkalinity and pH was shown to be moderate compared to fitted site densities, when calcite saturation was allowed to equilibrate. Calcite kinetics emerged as a potential source of error when fitting parameters in flow conditions. Fitted results were compared to data from previous batch and column studies completed on sediments from the Smith-Ranch Highland (SRH) site, to assess variability in derived parameters. Parameters from batch experiments were lower by a factor of 1.1 to 3.4 compared to column studies completed on the same sediments. The difference was attributed to errors in solid-solution ratios and the impact of calcite dissolution in batch experiments. Column studies conducted at two different laboratories showed almost an order of magnitude difference in fitted site densities suggesting that experimental methodology may play a bigger role in column sorption behavior than actual sediment heterogeneity. Our results demonstrate the necessity for ISR sites to remove residual pCO2 and equilibrate restoration water with background geochemistry to reduce uranium mobility. In addition, the observed variability between fitted parameters on the same sediments highlights the need to provide standardized guidelines and methodology for regulators and industry when the GC SCM approach is used for ISR risk assessments.

Uncertainty and variability in laboratory derived sorption parameters of sediments from a uranium in situ recovery site.

PubMed

Dangelmayr, Martin A; Reimus, Paul W; Johnson, Raymond H; Clay, James T; Stone, James J

2018-06-01

This research assesses the ability of a GC SCM to simulate uranium transport under variable geochemical conditions typically encountered at uranium in-situ recovery (ISR) sites. Sediment was taken from a monitoring well at the SRH site at depths 192 and 193 m below ground and characterized by XRD, XRF, TOC, and BET. Duplicate column studies on the different sediment depths, were flushed with synthesized restoration waters at two different alkalinities (160 mg/l CaCO 3 and 360 mg/l CaCO 3 ) to study the effect of alkalinity on uranium mobility. Uranium breakthrough occurred 25% - 30% earlier in columns with 360 mg/l CaCO 3 over columns fed with 160 mg/l CaCO 3 influent water. A parameter estimation program (PEST) was coupled to PHREEQC to derive site densities from experimental data. Significant parameter fittings were produced for all models, demonstrating that the GC SCM approach can model the impact of carbonate on uranium in flow systems. Derived site densities for the two sediment depths were between 141 and 178 μmol-sites/kg-soil, demonstrating similar sorption capacities despite heterogeneity in sediment mineralogy. Model sensitivity to alkalinity and pH was shown to be moderate compared to fitted site densities, when calcite saturation was allowed to equilibrate. Calcite kinetics emerged as a potential source of error when fitting parameters in flow conditions. Fitted results were compared to data from previous batch and column studies completed on sediments from the Smith-Ranch Highland (SRH) site, to assess variability in derived parameters. Parameters from batch experiments were lower by a factor of 1.1 to 3.4 compared to column studies completed on the same sediments. The difference was attributed to errors in solid-solution ratios and the impact of calcite dissolution in batch experiments. Column studies conducted at two different laboratories showed almost an order of magnitude difference in fitted site densities suggesting that experimental methodology may play a bigger role in column sorption behavior than actual sediment heterogeneity. Our results demonstrate the necessity for ISR sites to remove residual pCO2 and equilibrate restoration water with background geochemistry to reduce uranium mobility. In addition, the observed variability between fitted parameters on the same sediments highlights the need to provide standardized guidelines and methodology for regulators and industry when the GC SCM approach is used for ISR risk assessments. Copyright © 2018 Elsevier B.V. All rights reserved.

Uranium aqueous speciation in the vicinity of the former uranium mining sites using the diffusive gradients in thin films and ultrafiltration techniques.

PubMed

Drozdzak, Jagoda; Leermakers, Martine; Gao, Yue; Elskens, Marc; Phrommavanh, Vannapha; Descostes, Michael

2016-03-24

The performance of the Diffusive Gradients in Thin films (DGT) technique with Chelex(®)-100, Metsorb™ and Diphonix(®) as binding phases was evaluated in the vicinity of the former uranium mining sites of Chardon and L'Ecarpière (Loire-Atlantique department in western France). This is the first time that the DGT technique with three different binding agents was employed for the aqueous U determination in the context of uranium mining environments. The fractionation and speciation of uranium were investigated using a multi-methodological approach using filtration (0.45 μm, 0.2 μm), ultrafiltration (500 kDa, 100 kDa and 10 kDa) coupled to geochemical speciation modelling (PhreeQC) and the DGT technique. The ultrafiltration data showed that at each sampling point uranium was present mostly in the 10 kDa truly dissolved fraction and the geochemical modelling speciation calculations indicated that U speciation was markedly predominated by CaUO2(CO3)3(2-). In natural waters, no significant difference was observed in terms of U uptake between Chelex(®)-100 and Metsorb™, while similar or inferior U uptake was observed on Diphonix(®) resin. In turn, at mining influenced sampling spots, the U accumulation on DGT-Diphonix(®) was higher than on DGT-Chelex(®)-100 and DGT-Metsorb™, probably because their performance was disturbed by the extreme composition of the mining waters. The use of Diphonix(®) resin leads to a significant advance in the application and development of the DGT technique for determination of U in mining influenced environments. This investigation demonstrated that such multi-technique approach provides a better picture of U speciation and enables to assess more accurately the potentially bioavailable U pool. Copyright © 2016 Elsevier B.V. All rights reserved.

Molybdenum isotope fractionation during acid leaching of a granitic uranium ore

NASA Astrophysics Data System (ADS)

Migeon, Valérie; Bourdon, Bernard; Pili, Eric; Fitoussi, Caroline

2018-06-01

As an attempt to prevent illicit trafficking of nuclear materials, it is critical to identify the origin and transformation of uranium materials from the nuclear fuel cycle based on chemical and isotope tracers. The potential of molybdenum (Mo) isotopes as tracers is considered in this study. We focused on leaching, the first industrial process used to release uranium from ores, which is also known to extract Mo depending on chemical conditions. Batch experiments were performed in the laboratory with pH ranging from 0.3 to 5.5 in sulfuric acid. In order to span a large range in uranium and molybdenum yields, oxidizers such as nitric acid, hydrogen peroxide and manganese dioxide were also added. An enrichment in heavy Mo isotopes is produced in the solution during leaching of a granitic uranium ore, when Mo recovery is not quantitative. At least two Mo reservoirs were identified in the ore: ∼40% as Mo oxides soluble in water or sulfuric acid, and ∼40% of Mo hosted in sulfides soluble in nitric acid or hydrogen peroxide. At pH > 1.8, adsorption and/or precipitation processes induce a decrease in Mo yields with time correlated with large Mo isotope fractionations. Quantitative models were used to evaluate the relative importance of the processes involved in Mo isotope fractionation: dissolution, adsorption, desorption, precipitation, polymerization and depolymerization. Model best fits are obtained when combining the effects of dissolution/precipitation, and adsorption/desorption onto secondary minerals. These processes are inferred to produce an equilibrium isotope fractionation, with an enrichment in heavy Mo isotopes in the liquid phase and in light isotopes in the solid phase. Quantification of Mo isotope fractionation resulting from uranium leaching is thus a promising tool to trace the origin and transformation of nuclear materials. Our observations of Mo leaching are also consistent with observations of natural Mo isotope fractionation taking place during chemical weathering in terrestrial environments where the role of secondary processes such as adsorption is significant.

Study of polyethyleneimine- and amidoxime-functionalized hybrid biomass of Spirulina (Arthrospira) platensis for adsorption of uranium (VI) ion.

PubMed

Bayramoglu, Gulay; Akbulut, Aydin; Arica, M Yakup

2015-11-01

This study investigates the potential application of the polyethyleneimine- (PEI) and amidoxime-modified Spirulina (Arthrospira) platensis biomasses for the removal of uranium ion in batch mode using the native biomass as a control system. The uranium ion adsorption was also characterized by attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra, zeta potential analysis, and surface area measurement studies. The effects of pH, biomass amount, contact time, initial uranium ion concentration, and ionic strength were evaluated by using native and modified algal biomass preparations. The uranium ion removal was rapid, with more than 70% of total adsorption taking place in 40 min, and equilibrium was established within 60 min. From the experimental data, it was found that the amount of adsorption uranium ion on the algal preparations decreased in the following series: amidoxime-modified algal biomass > PEI-modified algal biomass > native algal biomass. Maximum adsorption capacities of amidoxime- and PEI-modified, and native algal biomasses were found to be 366.8, 279.5, and 194.6 mg/g, respectively, in batchwise studies. The adsorption rate of U(VI) ion by amidoxime-modified algal biomass was higher than those of the native and PEI-modified counterparts. The adsorption processes on all the algal biomass preparations followed by the Dubinin-Radushkevitch (D-R) and Temkin isotherms and pseudo-second-order kinetic models. The thermodynamic parameters were determined at four different temperatures (i.e., 15, 25, 35, and 45 °C) using the thermodynamics constant of the Temkin isotherm model. The ΔH° and ΔG° values of U(VI) ion adsorption on algal preparations show endothermic heat of adsorption; higher temperatures favor the process. The native and modified algal biomass preparations were regenerated using 10 mM HNO3. These results show that amidoxime-modified algal biomass can be a potential candidate for effective removal of U(VI) ion from aqueous solution.

Gold and palladium minerals (including empirical PdCuBiSe3) from the former Roter Bär mine, St. Andreasberg, Harz Mountains, Germany: a result of low-temperature, oxidising fluid overprint

NASA Astrophysics Data System (ADS)

Cabral, Alexandre Raphael; Ließmann, Wilfried; Lehmann, Bernd

2015-10-01

At Roter Bär, a former underground mine in the polymetallic deposits of St. Andreasberg in the middle-Harz vein district, Germany, native gold and palladium minerals occur very locally in clausthalite-hematite pockets of few millimetres across in carbonate veinlets. The native gold is a Au-Ag intermetallic compound and the palladium minerals are characterised as mertieite-II [Pd8(Sb,As)3] and empirical PdCuBiSe3 with some S. The latter coexists with bohdanowiczite (AgBiSe2), a mineral that is stable below 120 °C. The geological setting of Roter Bär, underneath a post-Variscan unconformity, and its hematite-selenide-gold association suggest that oxidising hydrothermal brines of low temperature were instrumental to the Au-Pd mineralisation. The Roter Bär Au-Pd mineralisation can be explained by Permo-Triassic, red-bed-derived brines in the context of post-Variscan, unconformity-related fluid overprint.

Sequence stratigraphic control on prolific HC reservoir development, Southwest Iran

USGS Publications Warehouse

Lasemi, Y.; Kondroud, K.N.

2008-01-01

An important carbonate formation in the Persian Gulf and the onshore oil fields of Southwest Iran is the Lowermost Cretaceous Fahliyan formation. The formation in Darkhowain field consists of unconformity-bounded depositional sequences containing prolific hydrocarbon reservoirs of contrasting origin. Located in the high stand systems tract (HST) of the lower sequence encompassing over 200m of oil column are the most prolific reservoir. Another reservoir is over 80m thick consisting of shallowing-upward cycles that are best developed within the transgressive systems tract of the upper sequence. Vertical facies distribution and their paleobathymetry and geophysical log signatures of the Fahliyan formation in the Darkhowain platform reveal the presence of two unconformity-bounded depositional sequences in Vail et al., Van Wagoner et al., and Sarg. The Fahliyan formation mainly consists of platform carbonates composed of restricted bioclastic lime mudstone to packstone of the platform interior, Lithocodium boundstone or ooid-intraclast-bioclast grainstone of the high energy platform margin and the bioclast packstone to lime mudstone related to the off-platform setting.

Martian crater degradation by eolian processes: Analogy with the Rio Cuarto Crater Field, Argentina

NASA Technical Reports Server (NTRS)

Grant, J. A.; Schultz, P. H.

1993-01-01

Numerous degraded and rimless craters occur across broad areas of the Martian surface that are mantled by thick, unconformable deposits. These regions include Arabia, Mesogaea, Electris, Tempe, the interior and surface to the northwest of Isidis Basin, southern Ismenius Lacus, and the polar layered terrains. Occurrence of the deposits and low regional thermal inertias indicate that at least some accumulated fine-grained sediment (effective particle diameters of 0.1-0.5 mm or coarse silt to medium sand) to a thickness of 100's to 1000's of meters. Most unconformable deposits experienced some eolian modification that may be recent in some locales. Despite the presence of these deposits, simple eolian deposition appears incapable of creating the numerous degraded and rimless craters occurring within their limits. Nevertheless, terrestrial analyses of the Rio Cuario craters formed into loessoid deposits demonstrates that eolian redistribution of fine-grained sediment in and around craters produces degraded morphologies that are analogous to some found in mantled regions on Mars.

Radiological Modeling for Determination of Derived Concentration Levels of an Area with Uranium Residual Material - 13533

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perez-Sanchez, Danyl

As a result of a pilot project developed at the old Spanish 'Junta de Energia Nuclear' to extract uranium from ores, tailings materials were generated. Most of these residual materials were sent back to different uranium mines, but a small amount of it was mixed with conventional building materials and deposited near the old plant until the surrounding ground was flattened. The affected land is included in an area under institutional control and used as recreational area. At the time of processing, uranium isotopes were separated but other radionuclides of the uranium decay series as Th-230, Ra-226 and daughters remainmore » in the residue. Recently, the analyses of samples taken at different ground's depths confirmed their presence. This paper presents the methodology used to calculate the derived concentration level to ensure that the reference dose level of 0.1 mSv y-1 used as radiological criteria. In this study, a radiological impact assessment was performed modeling the area as recreational scenario. The modelization study was carried out with the code RESRAD considering as exposure pathways, external irradiation, inadvertent ingestion of soil, inhalation of resuspended particles, and inhalation of radon (Rn-222). As result was concluded that, if the concentration of Ra-226 in the first 15 cm of soil is lower than, 0.34 Bq g{sup -1}, the dose would not exceed the reference dose. Applying this value as a derived concentration level and comparing with the results of measurements on the ground, some areas with a concentration of activity slightly higher than latter were found. In these zones the remediation proposal has been to cover with a layer of 15 cm of clean material. This action represents a reduction of 85% of the dose and ensures compliance with the reference dose. (authors)« less

Microwave-assisted of dispersive liquid-liquid microextraction and spectrophotometric determination of uranium after optimization based on Box-Behnken design and chemometrics methods.

PubMed

Niazi, Ali; Khorshidi, Neda; Ghaemmaghami, Pegah

2015-01-25

In this study an analytical procedure based on microwave-assisted dispersive liquid-liquid microextraction (MA-DLLME) and spectrophotometric coupled with chemometrics methods is proposed to determine uranium. In the proposed method, 4-(2-pyridylazo) resorcinol (PAR) is used as a chelating agent, and chloroform and ethanol are selected as extraction and dispersive solvent. The optimization strategy is carried out by using two level full factorial designs. Results of the two level full factorial design (2(4)) based on an analysis of variance demonstrated that the pH, concentration of PAR, amount of dispersive and extraction solvents are statistically significant. Optimal condition for three variables: pH, concentration of PAR, amount of dispersive and extraction solvents are obtained by using Box-Behnken design. Under the optimum conditions, the calibration graphs are linear in the range of 20.0-350.0 ng mL(-1) with detection limit of 6.7 ng mL(-1) (3δB/slope) and the enrichment factor of this method for uranium reached at 135. The relative standard deviation (R.S.D.) is 1.64% (n=7, c=50 ng mL(-1)). The partial least squares (PLS) modeling was used for multivariate calibration of the spectrophotometric data. The orthogonal signal correction (OSC) was used for preprocessing of data matrices and the prediction results of model, with and without using OSC, were statistically compared. MA-DLLME-OSC-PLS method was presented for the first time in this study. The root mean squares error of prediction (RMSEP) for uranium determination using PLS and OSC-PLS models were 4.63 and 0.98, respectively. This procedure allows the determination of uranium synthesis and real samples such as waste water with good reliability of the determination. Copyright © 2014. Published by Elsevier B.V.

Laser probe /sup 40/Ar//sup 39/Ar and conventional K/Ar dating of illites associated with the McClean Uranium deposits, N. Saskatchewan, Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bray, C.J.; Spooner, E.T.C.; Hall, C.M.

Mineralization at McClean occurs in elongate pods at the unconformity between the Athabasca sandstone sequence and the underlying Archean/Aphebian basement. Laser probe /sup 40/Ar//sup 39/Ar and conventional K/Ar dates were obtained on illites from the following environments (i) alteration halo around high grade U(-Ni-Co) mineralization, (ii) recrystallized sedimentary layers within the sandstone sequence, (iii) interstitial to quartz grains in sandstone, and (iv) regolith. The alteration halo illites gave ages between 1321+/-44 and 1002+/-33 Ma (n=20) which are in good agreement with published U-Pb dates on other U deposits in the area. One sample was analyzed twice, and gave a significantmore » age difference of 20 Ma. Hence the age range is interpreted as being either a reflection of variable argon retentivity or due to continued hydrothermal activity (i.e. U mineralization) or a combination of both. Dates obtained on (ii), (iii) and (iv) were 1438-1038 (n=8), 1459-1113 (n=3) and 1482-1262 (n=6) Ma respectively. The older ages are in good agreement with a published Rb-Sr whole rock age of 1470 Ma on tuffaceous sediments from the Athabasca group. The spread to younger ages is interpreted as due to resetting by the hot (approx. 200/sup 0/C) formation water which transported the U, and variable argon retentivity. Diffusion studies on a single sample of illite from the sedimentary sequence indicate a low blocking temperature of about 140/sup 0/C and imply that there have been very low temperatures in the area for the last 1000 Ma.« less

Exploration of dysprosium: the most critical element for Japan

NASA Astrophysics Data System (ADS)

Watanabe, Y.

2012-04-01

Dysprosium (Dy), one of the heavy rare earth elements, is used mainly as an additive for NdFeB permanent magnets which are installed in various modern industrial products such as voice coil motors in computers, factory automation machinery, hybrid and electric vehicles, home electronics, and wind turbine, to improve heat resistance of the magnets. Dy has been produced about 2,000t per year from the ores from ion adsorption type deposits in southern China. However, the produced amount of Dy was significantly reduced in 2011 in China due to reservation of heavy rare earth resources and protection of natural environment, resulting in soaring of Dy price in the world. In order to respond the increasing demand of Dy, unconventional supply sources are inevitably developed, in addition to heavy rare earth enriched ion adsorption type deposits outside China. Heavy rare earth elements including Dy are dominantly hosted in xenotime, fergusonite, zircon, eudialyte, keiviite, kainosite, iimoriite, etc. Concentration of xenotime is found in placer deposits in Malaysia and India, hydrothermal deposits associated with unconformity-type uranium mineralization (Athabasca basin in Canada, Western Australia), iron-oxide fluorite mineralization (South Africa) and Sn-bearing alkaline granite (Brazil). Zircon and fergusontie concentration is found as igneous and hydrothermal products in peralkaline syenite, alkaline granite and pegmatite (e.g., Nechalacho in Canada). Eudialyte concentration is found in some peralkaline syenite bodies in Greenland, Canada, Sweden and Russia. Among these sources, large Dy resources are estimated in the deposits hosted in peralkaline rocks (Nechalacho: 79,000t, Kvanefjeld: 49,000t, Norra Karr: 15,700t, etc.) compared to the present demand of Dy. Thus, Dy will be supplied from the deposits associated with peralkaline and alkaline deposits in future instead of ion adsorption type deposits in southern China.

A modified Embedded-Atom Method interatomic potential for uranium-silicide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beeler, Benjamin; Baskes, Michael; Andersson, David

Uranium-silicide (U-Si) fuels are being pursued as a possible accident tolerant fuel (ATF). This uranium alloy fuel bene ts from higher thermal conductivity and higher ssile density compared to uranium dioxide (UO 2). In order to perform engineering scale nuclear fuel performance simulations, the material properties of the fuel must be known. Currently, the experimental data available for U-Si fuels is rather limited. Thus, multiscale modeling e orts are underway to address this gap in knowledge. In this study, a semi-empirical modi ed Embedded-Atom Method (MEAM) potential is presented for the description of the U-Si system. The potential is ttedmore » to the formation energy, defect energies and structural properties of U 3Si 2. The primary phase of interest (U 3Si 2) is accurately described over a wide temperature range and displays good behavior under irradiation and with free surfaces. The potential can also describe a variety of U-Si phases across the composition spectrum.« less

On the valence fluctuation in the early actinide metals

DOE PAGES

Soderlind, P.; Landa, A.; Tobin, J. G.; ...

2015-12-15

In this study, recent X-ray measurements suggest a degree of valence fluctuation in plutonium and uranium intermetallics. We are applying a novel scheme, in conjunction with density functional theory, to predict 5f configuration fractions of states with valence fluctuations for the early actinide metals. For this purpose we perform constrained integer f-occupation calculations for the α phases of uranium, neptunium, and plutonium metals. For plutonium we also investigate the δ phase. The model predicts uranium and neptunium to be dominated by the f 3 and f 4 configurations, respectively, with only minor contributions from other configurations. For plutonium (both αmore » and δ phase) the scenario is dramatically different. Here, the calculations predict a relatively even distribution between three valence configurations. The δ phase has a greater configuration fraction of f 6 compared to that of the α phase. The theory is consistent with the interpretations of modern X-ray experiments and we present resonant X-ray emission spectroscopy results for α-uranium.« less

Mortality in a Combined Cohort of Uranium Enrichment Workers

PubMed Central

Yiin, James H.; Anderson, Jeri L.; Daniels, Robert D.; Bertke, Stephen J.; Fleming, Donald A.; Tollerud, David J.; Tseng, Chih-Yu; Chen, Pi-Hsueh; Waters, Kathleen M.

2017-01-01

Objective To examine the patterns of cause-specific mortality and relationship between internal exposure to uranium and specific causes in a pooled cohort of 29,303 workers employed at three former uranium enrichment facilities in the United States with follow-up through 2011. Methods Cause-specific standardized mortality ratios (SMRs) for the full cohort were calculated with the U.S. population as referent. Internal comparison of the dose-response relation between selected outcomes and estimated organ doses was evaluated using regression models. Results External comparison with the U.S. population showed significantly lower SMRs in most diseases in the pooled cohort. Internal comparison showed positive associations of absorbed organ doses with multiple myeloma, and to a lesser degree with kidney cancer. Conclusion In general, these gaseous diffusion plant workers had significantly lower SMRs than the U.S. population. The internal comparison however, showed associations between internal organ doses and diseases associated with uranium exposure in previous studies. PMID:27753121

SRTC criticality safety technical review: Nuclear Criticality Safety Evaluation 93-04 enriched uranium receipt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rathbun, R.

Review of NMP-NCS-930087, {open_quotes}Nuclear Criticality Safety Evaluation 93-04 Enriched Uranium Receipt (U), July 30, 1993, {close_quotes} was requested of SRTC (Savannah River Technology Center) Applied Physics Group. The NCSE is a criticality assessment to determine the mass limit for Engineered Low Level Trench (ELLT) waste uranium burial. The intent is to bury uranium in pits that would be separated by a specified amount of undisturbed soil. The scope of the technical review, documented in this report, consisted of (1) an independent check of the methods and models employed, (2) independent HRXN/KENO-V.a calculations of alternate configurations, (3) application of ANSI/ANS 8.1,more » and (4) verification of WSRC Nuclear Criticality Safety Manual procedures. The NCSE under review concludes that a 500 gram limit per burial position is acceptable to ensure the burial site remains in a critically safe configuration for all normal and single credible abnormal conditions. This reviewer agrees with that conclusion.« less

A modified Embedded-Atom Method interatomic potential for uranium-silicide

DOE PAGES

Beeler, Benjamin; Baskes, Michael; Andersson, David; ...

2017-08-18

Uranium-silicide (U-Si) fuels are being pursued as a possible accident tolerant fuel (ATF). This uranium alloy fuel bene ts from higher thermal conductivity and higher ssile density compared to uranium dioxide (UO 2). In order to perform engineering scale nuclear fuel performance simulations, the material properties of the fuel must be known. Currently, the experimental data available for U-Si fuels is rather limited. Thus, multiscale modeling e orts are underway to address this gap in knowledge. In this study, a semi-empirical modi ed Embedded-Atom Method (MEAM) potential is presented for the description of the U-Si system. The potential is ttedmore » to the formation energy, defect energies and structural properties of U 3Si 2. The primary phase of interest (U 3Si 2) is accurately described over a wide temperature range and displays good behavior under irradiation and with free surfaces. The potential can also describe a variety of U-Si phases across the composition spectrum.« less

A modified Embedded-Atom Method interatomic potential for uranium-silicide

NASA Astrophysics Data System (ADS)

Beeler, Benjamin; Baskes, Michael; Andersson, David; Cooper, Michael W. D.; Zhang, Yongfeng

2017-11-01

Uranium-silicide (U-Si) fuels are being pursued as a possible accident tolerant fuel (ATF). This uranium alloy fuel benefits from higher thermal conductivity and higher fissile density compared to uranium dioxide (UO2). In order to perform engineering scale nuclear fuel performance simulations, the material properties of the fuel must be known. Currently, the experimental data available for U-Si fuels is rather limited. Thus, multiscale modeling efforts are underway to address this gap in knowledge. In this study, a semi-empirical modified Embedded-Atom Method (MEAM) potential is presented for the description of the U-Si system. The potential is fitted to the formation energy, defect energies and structural properties of U3Si2. The primary phase of interest (U3Si2) is accurately described over a wide temperature range and displays good behavior under irradiation and with free surfaces. The potential can also describe a variety of U-Si phases across the composition spectrum.

Microfluidic Experiments Studying Pore Scale Interactions of Microbes and Geochemistry

NASA Astrophysics Data System (ADS)

Chen, M.; Kocar, B. D.

2016-12-01

Understanding how physical phenomena, chemical reactions, and microbial behavior interact at the pore-scale is crucial to understanding larger scale trends in groundwater chemistry. Recent studies illustrate the utility of microfluidic devices for illuminating pore-scale physical-biogeochemical processes and their control(s) on the cycling of iron, uranium, and other important elements 1-3. These experimental systems are ideal for examining geochemical reactions mediated by microbes, which include processes governed by complex biological phenomenon (e.g. biofilm formation, etc.)4. We present results of microfluidic experiments using a model metal reducing bacteria and varying pore geometries, exploring the limitations of the microorganisms' ability to access tight pore spaces, and examining coupled biogeochemical-physical controls on the cycling of redox sensitive metals. Experimental results will provide an enhanced understanding of coupled physical-biogeochemical processes transpiring at the pore-scale, and will constrain and compliment continuum models used to predict and describe the subsurface cycling of redox-sensitive elements5. 1. Vrionis, H. A. et al. Microbiological and geochemical heterogeneity in an in situ uranium bioremediation field site. Appl. Environ. Microbiol. 71, 6308-6318 (2005). 2. Pearce, C. I. et al. Pore-scale characterization of biogeochemical controls on iron and uranium speciation under flow conditions. Environ. Sci. Technol. 46, 7992-8000 (2012). 3. Zhang, C., Liu, C. & Shi, Z. Micromodel investigation of transport effect on the kinetics of reductive dissolution of hematite. Environ. Sci. Technol. 47, 4131-4139 (2013). 4. Ginn, T. R. et al. Processes in microbial transport in the natural subsurface. Adv. Water Resour. 25, 1017-1042 (2002). 5. Scheibe, T. D. et al. Coupling a genome-scale metabolic model with a reactive transport model to describe in situ uranium bioremediation. Microb. Biotechnol. 2, 274-286 (2009).

A Uranium Bioremediation Reactive Transport Benchmark

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yabusaki, Steven B.; Sengor, Sevinc; Fang, Yilin

A reactive transport benchmark problem set has been developed based on in situ uranium bio-immobilization experiments that have been performed at a former uranium mill tailings site in Rifle, Colorado, USA. Acetate-amended groundwater stimulates indigenous microorganisms to catalyze the reduction of U(VI) to a sparingly soluble U(IV) mineral. The interplay between the flow, acetate loading periods and rates, microbially-mediated and geochemical reactions leads to dynamic behavior in metal- and sulfate-reducing bacteria, pH, alkalinity, and reactive mineral surfaces. The benchmark is based on an 8.5 m long one-dimensional model domain with constant saturated flow and uniform porosity. The 159-day simulation introducesmore » acetate and bromide through the upgradient boundary in 14-day and 85-day pulses separated by a 10 day interruption. Acetate loading is tripled during the second pulse, which is followed by a 50 day recovery period. Terminal electron accepting processes for goethite, phyllosilicate Fe(III), U(VI), and sulfate are modeled using Monod-type rate laws. Major ion geochemistry modeled includes mineral reactions, as well as aqueous and surface complexation reactions for UO2++, Fe++, and H+. In addition to the dynamics imparted by the transport of the acetate pulses, U(VI) behavior involves the interplay between bioreduction, which is dependent on acetate availability, and speciation-controlled surface complexation, which is dependent on pH, alkalinity and available surface complexation sites. The general difficulty of this benchmark is the large number of reactions (74), multiple rate law formulations, a multisite uranium surface complexation model, and the strong interdependency and sensitivity of the reaction processes. Results are presented for three simulators: HYDROGEOCHEM, PHT3D, and PHREEQC.« less

Extended burnup core management for once-through uranium fuel cycles in LWRS. First annual report for the period 1 July 1979-30 June 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sesonske, A.

1980-08-01

Detailed core management arrangements are developed requiring four operating cycles for the transition from present three-batch loading to an extended burnup four-batch plan for Zion-1. The ARMP code EPRI-NODE-P was used for core modeling. Although this work is preliminary, uranium and economic savings during the transition cycles appear of the order of 6 percent.

Onset conditions for flash sintering of UO 2

DOE PAGES

Raftery, Alicia M.; Pereira da Silva, João Gustavo; Byler, Darrin D.; ...

2017-06-22

In this paper, flash sintering was demonstrated on stoichiometric and non-stoichiometric uranium dioxide pellets at temperatures ranging from room temperature (26°C) up to 600°C. The onset conditions for flash sintering were determined for three stoichiometries (UO 2.00, UO 2.08, and UO 2.16) and analyzed against an established thermal runaway model. The presence of excess oxygen was found to enhance the flash sintering onset behavior of uranium dioxide, lowering the field required to flash and shortening the time required for a flash to occur. Finally, the results from this study highlight the effect of stoichiometry on the flash sintering behavior ofmore » uranium dioxide and will serve as the foundation for future studies on this material.« less

Potentiality of uranium biosorption from nitric acid solutions using shrimp shells.

PubMed

Ahmed, S H; El Sheikh, E M; Morsy, A M A

2014-08-01

Biosorption has gained important credibility during recent years because of its good performance and low cost. This work is concerned with studying the potentiality of the chitin component of the shrimp shells for uranium biosorption from nitric acid liquid solutions. The structural characteristics of the working chitin have been determined via Fourier Transform Infrared Spectroscopy (FTIR). The surface morphology was examined using Scanning Electron Microscopy (SEM). The adsorption capacity of biomass was investigated experimentally. The influence of contact time, pH, metal ion concentration, solution volume to mass ratio and temperature were evaluated and the results were fitted using adsorption isotherm models. The kinetic of uranium biosorption was also investigated as well as biosorption thermodynamic. Copyright © 2014 Elsevier Ltd. All rights reserved.

Ground-water contamination near a uranium tailings disposal site in Colorado

USGS Publications Warehouse

Goode, Daniel J.; Wilder, Russell J.

1987-01-01

Contaminants from uranium tailings disposed of at an active mill in Colorado have seeped into the shallow ground water onsite. This ground water discharges into the Arkansas River Valley through a superposed stream channel cut in the resistant sandstone ridge at the edge of a synclinal basin. In the river valley, seasonal surface-water irrigation has a significant impact on hydrodynamics. Water levels in residential wells fluctuate up to 20 ft and concentrations of uranium, molybdenum, and other contaminants also vary seasonally, with highest concentrations in the Spring, prior to irrigation, and lowest concentrations in the Fall. Results of a simple transient mixing cell model support the hypothesis that lateral ground-water inflow, and not irrigation recharge, is the source of ground-water contamination.

Onset conditions for flash sintering of UO2

NASA Astrophysics Data System (ADS)

Raftery, Alicia M.; Pereira da Silva, João Gustavo; Byler, Darrin D.; Andersson, David A.; Uberuaga, Blas P.; Stanek, Christopher R.; McClellan, Kenneth J.

2017-09-01

In this work, flash sintering was demonstrated on stoichiometric and non-stoichiometric uranium dioxide pellets at temperatures ranging from room temperature (26 °C) up to 600 °C . The onset conditions for flash sintering were determined for three stoichiometries (UO2.00, UO2.08, and UO2.16) and analyzed against an established thermal runaway model. The presence of excess oxygen was found to enhance the flash sintering onset behavior of uranium dioxide, lowering the field required to flash and shortening the time required for a flash to occur. The results from this study highlight the effect of stoichiometry on the flash sintering behavior of uranium dioxide and will serve as the foundation for future studies on this material.

40 CFR 421.320 - Applicability: Description of the secondary uranium subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... secondary uranium subcategory. 421.320 Section 421.320 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Secondary Uranium Subcategory § 421.320 Applicability: Description of the secondary uranium... uranium (including depleted uranium) by secondary uranium facilities. ...

40 CFR 421.320 - Applicability: Description of the secondary uranium subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... secondary uranium subcategory. 421.320 Section 421.320 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Secondary Uranium Subcategory § 421.320 Applicability: Description of the secondary uranium... uranium (including depleted uranium) by secondary uranium facilities. ...

40 CFR 421.320 - Applicability: Description of the secondary uranium subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... secondary uranium subcategory. 421.320 Section 421.320 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Secondary Uranium Subcategory § 421.320 Applicability: Description of the secondary uranium... uranium (including depleted uranium) by secondary uranium facilities. ...

40 CFR 421.320 - Applicability: Description of the secondary uranium subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... secondary uranium subcategory. 421.320 Section 421.320 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Secondary Uranium Subcategory § 421.320 Applicability: Description of the secondary uranium... uranium (including depleted uranium) by secondary uranium facilities. ...

40 CFR 421.320 - Applicability: Description of the secondary uranium subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... secondary uranium subcategory. 421.320 Section 421.320 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Secondary Uranium Subcategory § 421.320 Applicability: Description of the secondary uranium... uranium (including depleted uranium) by secondary uranium facilities. ...

Bioremediation of uranium contamination with enzymatic uranium reduction

USGS Publications Warehouse

Lovley, D.R.; Phillips, E.J.P.

1992-01-01

Enzymatic uranium reduction by Desulfovibrio desulfuricans readily removed uranium from solution in a batch system or when D. desulfuricans was separated from the bulk of the uranium-containing water by a semipermeable membrane. Uranium reduction continued at concentrations as high as 24 mM. Of a variety of potentially inhibiting anions and metals evaluated, only high concentrations of copper inhibited uranium reduction. Freeze-dried cells, stored aerobically, reduced uranium as fast as fresh cells. D. desulfuricans reduced uranium in pH 4 and pH 7.4 mine drainage waters and in uraniumcontaining groundwaters from a contaminated Department of Energy site. Enzymatic uranium reduction has several potential advantages over other bioprocessing techniques for uranium removal, the most important of which are as follows: the ability to precipitate uranium that is in the form of a uranyl carbonate complex; high capacity for uranium removal per cell; the formation of a compact, relatively pure, uranium precipitate.

Cell metal interactions: A comparison of natural uranium to other common metals in renal cells and bone osteoblasts

NASA Astrophysics Data System (ADS)

Milgram, S.; Carrière, M.; Thiebault, C.; Berger, P.; Khodja, H.; Gouget, B.

2007-07-01

Uranium acute intoxication has been documented to induce nephrotoxicity. Kidneys are the main target organs after short term exposures to high concentrations of the toxic, while chronic exposures lead to its accumulation in the skeleton. In this paper, chemical toxicity of uranium is investigated for rat osteoblastic bone cells and compared to results previously obtained on renal cells. We show that bone cells are less sensitive to uranium than renal cells. The influence of the chemical form on U cytotoxicity is demonstrated. For both cell types, a comparison of uranium toxicity with other metals or metalloids toxicities (Mn, Ni, Co, Cu, Zn, Se and Cd) permits classification of Cd, Zn, Se IV and Cu as the most toxic and Ni, Se VI, Mn and U as the least toxic. Chemical toxicity of natural uranium proves to be far less than that of cadmium. To try to explain the differences in sensitivities observed between metals and different cell types, cellular accumulations in cell monolayers are quantified by inductively coupled plasma-mass spectroscopy (ICP-MS), function of time or function of dose: lethal doses which simulate acute intoxications and sub-lethal doses which are more realistic with regard to environmentally metals concentrations. In addition to being more resistant, bone cells accumulated much more uranium than did renal cells. Moreover, for both cell models, Mn, U-citrate and U-bicarbonate are strongly accumulated whereas Cu, Zn and Ni are weakly accumulated. On the other hand, a strong difference in Cd behaviour between the two cell types is shown: whereas Cd is very weakly accumulated in bone cells, it is very strongly accumulated in renal cells. Finally, elemental distribution of the toxics is determined on a cellular scale using nuclear microprobe analysis. For both renal and osteoblastic cells, uranium was accumulated in as intracellular precipitates similar to those observed previously by SEM/EDS.

Thermodynamic Simulation of Equilibrium Composition of Reaction Products at Dehydration of a Technological Channel in a Uranium-Graphite Reactor

NASA Astrophysics Data System (ADS)

Pavliuk, A. O.; Zagumennov, V. S.; Kotlyarevskiy, S. G.; Bespala, E. V.

2018-01-01

The problems of accumulation of nuclear fuel spills in the graphite stack in the course of operation of uranium-graphite nuclear reactors are considered. The results of thermodynamic analysis of the processes in the graphite stack at dehydration of a technological channel, fuel element shell unsealing and migration of fission products, and activation of stable nuclides in structural elements of the reactor and actinides inside the graphite moderator are given. The main chemical reactions and compounds that are produced in these modes in the reactor channel during its operation and that may be hazardous after its shutdown and decommissioning are presented. Thermodynamic simulation of the equilibrium composition is performed using the specialized code TERRA. The results of thermodynamic simulation of the equilibrium composition in different cases of technological channel dehydration in the course of the reactor operation show that, if the temperature inside the active core of the nuclear reactor increases to the melting temperature of the fuel element, oxides and carbides of nuclear fuel are produced. The mathematical model of the nonstationary heat transfer in a graphite stack of a uranium-graphite reactor in the case of the technological channel dehydration is presented. The results of calculated temperature evolution at the center of the fuel element, the replaceable graphite element, the air gap, and in the surface layer of the block graphite are given. The numerical results show that, in the case of dehydration of the technological channel in the uranium-graphite reactor with metallic uranium, the main reaction product is uranium dioxide UO2 in the condensed phase. Low probability of production of pyrophoric uranium compounds (UH3) in the graphite stack is proven, which allows one to disassemble the graphite stack without the risk of spontaneous graphite ignition in the course of decommissioning of the uranium-graphite nuclear reactor.

Release behavior of uranium in uranium mill tailings under environmental conditions.

PubMed

Liu, Bo; Peng, Tongjiang; Sun, Hongjuan; Yue, Huanjuan

2017-05-01

Uranium contamination is observed in sedimentary geochemical environments, but the geochemical and mineralogical processes that control uranium release from sediment are not fully appreciated. Identification of how sediments and water influence the release and migration of uranium is critical to improve the prevention of uranium contamination in soil and groundwater. To understand the process of uranium release and migration from uranium mill tailings under water chemistry conditions, uranium mill tailing samples from northwest China were investigated with batch leaching experiments. Results showed that water played an important role in uranium release from the tailing minerals. The uranium release was clearly influenced by contact time, liquid-solid ratio, particle size, and pH under water chemistry conditions. Longer contact time, higher liquid content, and extreme pH were all not conducive to the stabilization of uranium and accelerated the uranium release from the tailing mineral to the solution. The values of pH were found to significantly influence the extent and mechanisms of uranium release from minerals to water. Uranium release was monitored by a number of interactive processes, including dissolution of uranium-bearing minerals, uranium desorption from mineral surfaces, and formation of aqueous uranium complexes. Considering the impact of contact time, liquid-solid ratio, particle size, and pH on uranium release from uranium mill tailings, reducing the water content, decreasing the porosity of tailing dumps and controlling the pH of tailings were the key factors for prevention and management of environmental pollution in areas near uranium mines. Copyright © 2017 Elsevier Ltd. All rights reserved.

Erosional unconformity or non-deposition? An alternative interpretation of the Eocene seismic stratigraphy offshore Wilkes Land, East Antarctica

NASA Astrophysics Data System (ADS)

Sauermilch, Isabel; Whittaker, Joanne; Totterdell, Jennifer; Jokat, Wilfried

2017-04-01

The sedimentary stratigraphy along the conjugate Australian-Antarctic continental margins provide insights into their tectonic evolution as well as changes in paleoceanographic conditions in the Southern Ocean. A comprehensive network of multichannel seismic reflection data as well as geological information from drill cores have been used to interpret the stratigraphic evolution of these margins. However, a number of alternative seismic interpretations exist for the Antarctic side, particularly due to sparse drill core information. A prominent high-amplitude reflector observed along the margin, extending from the continental shelf to the foot-of-slope, is at the centre of debate. Recently, two major hiatuses (from 33.6 - 47.9 Ma and 51.06 - 51.9 Ma) were recovered by the IODP drill core U1356A offshore Wilkes Land and correlated to this prominent reflector. Previous seismic stratigraphic investigations interpreted this structure as an erosional unconformity and proposed different events as a possible cause for this formation, including first arrival of the continental glaciation at the coast at about 34 Ma, increase in spreading rate between Australia and Antarctica at about 45 Ma and drastic global sea level drop of 70 m at about 43 Ma. However, such a large-scale erosion must consequently lead to a re-deposition of a significantly large amount of sediment somewhere along the margins, but, to date, no such deposition is observed in the seismic reflection data. Here, we present an alternative seismo-stratigraphic interpretation based on correlation to the sedimentary structures along the Australian margin. We argue that the prominent unconformity is formed due to non-deposition of sediment between 47.8 and 33.6 Ma. The sedimentary units underlying this unconformity show strong similarities in structure, seismic characteristics and variation along the margin with sequences that are partly exposed to the seafloor at the foot of the Australian slope. On the Australian flank, the age of these exposed sediment sequences ranges from 65 Ma to 45 Ma. Low to no sedimentation from 45 Ma to the present-day offshore Australia has been interpreted to explain the exposure of these old sediment units. We propose that non-deposition occurred along both margins from 45 Ma, until large-scale glacial deposition started at 33.6 Ma along the Antarctic margin. Using our new interpretation, we create paleo-bathymetric reconstructions using the software BALPAL at 83 Ma, 65 Ma and 45 Ma. The resulting paleo-bathymetric maps provide essential information, e.g. for paleo-oceanographic and -climatic investigations in the Southern Ocean.

The South China - Indochina collision: a perspective from sedimentary basins analysis

NASA Astrophysics Data System (ADS)

Rossignol, Camille; Bourquin, Sylvie; Hallot, Erwan; Poujol, Marc; Roger, Françoise; Dabard, Marie-Pierre; Martini, Rossana; Villeneuve, Michel; Cornée, Jean-Jacques; Peyrotty, Giovan

2017-04-01

Sedimentary basins, through the sedimentary successions and the nature of the deposits, reflect the geology of the area from which the sediments were derived and thus provide valuable record of hinterland tectonism. As the collision between the South China and the Indochina blocks (i.e., the Indosinian orogeny) is still the object of a number of controversies regarding, for instance, its timing and the polarity of the subduction, the sedimentary basins associated with this mountain belt are likely to provide clues to reconstruct its geodynamic evolution. However, both the Sam Nua Basin (located to the south of the inner zones of the Indosinian orogeny and the Song Ma ophiolites) and the Song Da Basin (located to the north of the inner zones), northern Vietnam, are still lacking important information regarding the depositional environments and the ages of the main formations that they contain. Using sedimentological and dating analyses (foraminifers biostratigraphy and U-Pb dating on detrital zircon), we provide a new stratigraphic framework for these basins and propose a geodynamic evolution of the present-day northern Vietnam. During the Early Triassic, the Sam Nua Basin was mainly supplied by volcaniclastic sediments originating from an active volcanic activity. Geochemical investigations, combined with sedimentological and structural analyses, support an arc-related setting for this magmatism. This magmatic arc resulted from the subduction of a south dipping oceanic slab that once separated the South China from the Indochina blocks. During the Middle to the Late Triassic, the Sam Nua Basin underwent erosion that lead to the formation of a major unconformity, termed the Indosinian unconformity. This unconformity is interpreted to result from the erosion of the Indosinian mountain belt, built after the continental collision between the South China and the Indochina blocks. Later, during the Late Triassic, the Sam Nua Basin experienced the deposition of very coarse material, emplaced under continental setting and representing the product of the erosion of the Indosinian mountain belt. To the North, the Song Da Basin is characterized by strongly diachronous deposits over a basal unconformity developed at the expense of volcanic and volcaniclastic deposits related to the Emeishan Large Igneous Province. The sedimentary succession indicates a foreland setting during the Early to the Middle Triassic, which contrasts with the commonly assumed rift setting for these sediments. Thus, the Song Da Basin documents the formation of the Indosinian thrust belt, located immediately to the South of the basin.

Assessing the duration of drowning episodes during the Early Cretaceous

NASA Astrophysics Data System (ADS)

Godet, A.; Föllmi, K. B.

2013-12-01

Drowning unconformities are stratigraphic key surfaces in the history of carbonate platforms. They mostly consist in the deposition of deep marine facies on top of shallow marine limestones. Although large-scale depositional geometries mimic lowstand systems track architecture, these sedimentary turnovers are developed in relation with major sea level rise, inducing an increase in the rate of creation of accommodation space that outpaces the capacity of carbonate to keep up. This so-called paradox of carbonate platform drowning implies that other parameters than purely eustatic fluctuations are involved in the demise of shallow marine ecosystems. Worldwide and at different time during Earth history, in-depth studies of drowning unconformities revealed that changes in nutrient input, clastic delivery, temperature, or a combination of them may be responsible for a decrease in light penetration in the water column and the progressive suffocation and poisoning of photosynthetic carbonate producers. The examination of such case examples from various stratigraphic intervals and palaeogeographical settings thus helps in identifying and hierarchizing potential triggering mechanisms for drowning unconformities. This is complemented by new data from Early Cretaceous successions from the Helvetic Alps. During this time period, the Helvetic carbonate platform developed along the northern Tethyan margin using both photozoan and heterozoan communities. Phases of healthy production were interrupted by several drowning episodes. The latter are marked in the sedimentary record by condensation and associated phosphogenesis and glauconitisation. From the earliest Valanginian to the early to late Barremian, three drowning unconformities reflect the intermittent installation of a more humid climate and subsequent enhanced trophic conditions, which first induced a switch from photozoan to heterozoan communities and then to long-lasting drowning phases. The latter encompass several sea level rise and fall cycles, and may be linked to strengthened upwelling currents. Moreover during the late Hauterivian - early Barremian time period, the correlation of platform carbonates with basinal sediments, by means of bio-, chemo- and sequence stratigraphy, allows to estimate the duration of a drowning episode. With the return to more oligotrophic conditions during the late Barremian, photozoan, Urgonian-type communities took up again. Their development has been abruptly stopped at the end of the early Aptian by a major emersion phase. The subsequent drowning is documented in various peritethyan areas. This initial crisis is followed by three other drowning phases that ultimately led to the replacement of shallow ecosystems by a deeper marine sedimentation in the Cenomanian. This long-term trend in the evolution of the Helvetic carbonate platform and of other peritethyan ecosystems may have been driven by more global phenomena.

Black shale source rocks and oil generation in the Cambrian and Ordovician of the central Appalachian Basin, USA

USGS Publications Warehouse

Ryder, R.T.; Burruss, R.C.; Hatch, J.R.

1998-01-01

Nearly 600 million bbl of oil (MMBO) and 1 to 1.5 trillion ft3 (tcf) of gas have been produced from Cambrian and Ordovician reservoirs (carbonate and sandstone) in the Ohio part of the Appalachian basin and on adjoining arches in Ohio, Indiana, and Ontario, Canada. Most of the oil and gas is concentrated in the giant Lima-Indiana field on the Findlay and Kankakee arches and in small fields distributed along the Knox unconformity. Based on new geochemical analyses of oils, potential source rocks, bitumen extracts, and previously published geochemical data, we conclude that the oils in both groups of fields originated from Middle and Upper Ordovician blcak shale (Utica and Antes shales) in the Appalachian basin. Moroever, we suggest that approximately 300 MMBO and many trillions of cubic feet of gas in the Lower Silurian Clinton sands of eastern Ohio originated in the same source rocks. Oils from the Cambrian and Ordovician reservoirs have similar saturated hydrocarbon compositions, biomarker distributions, and carbon isotope signatures. Regional variations in the oils are attributed to differences in thermal maturation rather than to differences in source. Total organic carbon content, genetic potential, regional extent, and bitument extract geochemistry identify the balck shale of the Utica and Antes shales as the most plausible source of the oils. Other Cambrian and Ordovician shale and carbonate units, such as the Wells Creek formation, which rests on the Knox unconformity, and the Rome Formation and Conasauga Group in the Rome trough, are considered to be only local petroleum sources. Tmax, CAI, and pyrolysis yields from drill-hole cuttings and core indicate that the Utica Shale in eastern and central Ohio is mature with respect to oil generation. Burial, thermal, and hydrocarbon-generation history models suggest that much of the oil was generated from the Utica-Antes source in the late Paleozoic during the Alleghanian orogeny. A pervasive fracture network controlled by basement tectonics aided in the distribution of oil from the source to the trap. This fracture network permitted oil to move laterally and stratigraphically downsection through eastward-dipping, impermeable carbonate sequences to carrier zones such as the Middle Ordovician Knox unconformity, and to reservoirs such as porous dolomite in the Middle Ordovician Trenton Limestone in the Lima-Indiana field. Some of the oil and gas from the Utica-Antes source escaped vertically through a partially fractured, leaky Upper Ordovician shale seal into widespread Lower Silurian sandstone reservoirs.Nearly 600 million bbl of oil (MMBO) and 1 to 1.5 trillion ft3 (tcf) of gas have been produced from Cambrian and Ordovician reservoirs (carbonate and sandstone) in the Ohio part of the Appalachian basin and on adjoining arches in Ohio, Indiana, and Ontario, Canada. Most of the oil and gas is concentrated in the giant Lima-Indiana field on the Findlay and Kankakee arches and in small fields distributed along the Knox unconformity. Based on new geochemical analyses of oils, potential source rocks, bitumen extracts, and previously published geochemical data, we conclude that the oils in both groups of fields originated from Middle and Upper Ordovician black shale (Utica and Antes shales) in the Appalachian basin. Moreover, we suggest that approximately 300 MMBO and many trillions of cubic feet of gas in the Lower Silurian Clinton sands of eastern Ohio originated in these same source rocks.

Effect of rapidly changing river stage on uranium flux through the hyporheic zone.

PubMed

Fritz, Brad G; Arntzen, Evan V

2007-01-01

Measurement of ground water/surface water interaction within the hyporheic zone is increasingly recognized as an important aspect of subsurface contaminant fate and transport. Understanding the interaction between ground water and surface water is critical in developing a complete conceptual model of contaminant transport through the hyporheic zone. At the Hanford Site near Richland, Washington, ground water contaminated with uranium discharges to the Columbia River through the hyporheic zone. Ground water flux varies according to changes in hydraulic gradient caused by fluctuating river stage, which changes in response to operation of dams on the Columbia River. Piezometers and continuous water quality monitoring probes were installed in the hyporheic zone to provide long-term, high-frequency measurement of hydraulic gradient and estimated uranium concentrations. Subsequently, the flux of water and uranium was calculated for each half-hour time period over a 15-month study period. In addition, measurement of water levels in the near-shore unconfined aquifer enhanced the understanding of the relationship between river stage, aquifer elevation, and uranium flux. Changing river stage resulted in fluctuating hydraulic gradient within the hyporheic zone. Further, influx of river water caused lower uranium concentrations as a result of dilution. The methods employed in this study provide a better understanding of the interaction between surface and ground water in a situation with a dynamically varying vertical hydraulic gradient and illustrate how the combination of relatively standard methods can be used to derive an accurate estimation of water and contaminant flux through the hyporheic zone.

Rate equation model of laser induced bias in uranium isotope ratios measured by resonance ionization mass spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isselhardt, B. H.; Prussin, S. G.; Savina, M. R.

2016-01-01

Resonance Ionization Mass Spectrometry (RIMS) has been developed as a method to measure uranium isotope abundances. In this approach, RIMS is used as an element-selective ionization process between uranium atoms and potential isobars without the aid of chemical purification and separation. The use of broad bandwidth lasers with automated feedback control of wavelength was applied to the measurement of the U-235/U-238 ratio to decrease laser-induced isotopic fractionation. In application, isotope standards are used to identify and correct bias in measured isotope ratios, but understanding laser-induced bias from first-principles can improve the precision and accuracy of experimental measurements. A rate equationmore » model for predicting the relative ionization probability has been developed to study the effect of variations in laser parameters on the measured isotope ratio. The model uses atomic data and empirical descriptions of laser performance to estimate the laser-induced bias expected in experimental measurements of the U-235/U-238 ratio. Empirical corrections are also included to account for ionization processes that are difficult to calculate from first principles with the available atomic data. Development of this model has highlighted several important considerations for properly interpreting experimental results.« less

Transgenerational Adaptation to Pollution Changes Energy Allocation in Populations of Nematodes.

PubMed

Goussen, Benoit; Péry, Alexandre R R; Bonzom, Jean-Marc; Beaudouin, Rémy

2015-10-20

Assessing the evolutionary responses of long-term exposed populations requires multigeneration ecotoxicity tests. However, the analysis of the data from these tests is not straightforward. Mechanistic models allow the in-depth analysis of the variation of physiological traits over many generations, by quantifying the trend of the physiological and toxicological parameters of the model. In the present study, a bioenergetic mechanistic model has been used to assess the evolution of two populations of the nematode Caenorhabditis elegans in control conditions or exposed to uranium. This evolutionary pressure resulted in a brood size reduction of 60%. We showed an adaptation of individuals of both populations to experimental conditions (increase of maximal length, decrease of growth rate, decrease of brood size, and decrease of the elimination rate). In addition, differential evolution was also highlighted between the two populations once the maternal effects had been diminished after several generations. Thus, individuals that were greater in maximal length, but with apparently a greater sensitivity to uranium were selected in the uranium population. In this study, we showed that this bioenergetics mechanistic modeling approach provided a precise, certain, and powerful analysis of the life strategy of C. elegans populations exposed to heavy metals resulting in an evolutionary pressure across successive generations.

Rate equation model of laser induced bias in uranium isotope ratios measured by resonance ionization mass spectrometry

DOE PAGES

Isselhardt, B. H.; Prussin, S. G.; Savina, M. R.; ...

2015-12-07

Resonance Ionization Mass Spectrometry (RIMS) has been developed as a method to measure uranium isotope abundances. In this approach, RIMS is used as an element-selective ionization process between uranium atoms and potential isobars without the aid of chemical purification and separation. The use of broad bandwidth lasers with automated feedback control of wavelength was applied to the measurement of the 235U/238U ratio to decrease laser-induced isotopic fractionation. In application, isotope standards are used to identify and correct bias in measured isotope ratios, but understanding laser-induced bias from first-principles can improve the precision and accuracy of experimental measurements. A rate equationmore » model for predicting the relative ionization probability has been developed to study the effect of variations in laser parameters on the measured isotope ratio. The model uses atomic data and empirical descriptions of laser performance to estimate the laser-induced bias expected in experimental measurements of the 235U/ 238U ratio. Empirical corrections are also included to account for ionization processes that are difficult to calculate from first principles with the available atomic data. As a result, development of this model has highlighted several important considerations for properly interpreting experimental results.« less

PDRD (SR13046) TRITIUM PRODUCTION FINAL REPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, P.; Sheetz, S.

Utilizing the results of Texas A&M University (TAMU) senior design projects on tritium production in four different small modular reactors (SMR), the Savannah River National Laboratory’s (SRNL) developed an optimization model evaluating tritium production versus uranium utilization under a FY2013 plant directed research development (PDRD) project. The model is a tool that can evaluate varying scenarios and various reactor designs to maximize the production of tritium per unit of unobligated United States (US) origin uranium that is in limited supply. The primary module in the model compares the consumption of uranium for various production reactors against the base case ofmore » Watts Bar I running a nominal load of 1,696 tritium producing burnable absorber rods (TPBARs) with an average refueling of 41,000 kg low enriched uranium (LEU) on an 18 month cycle. After inputting an initial year, starting inventory of unobligated uranium and tritium production forecast, the model will compare and contrast the depletion rate of the LEU between the entered alternatives. This is an annual tritium production rate of approximately 0.059 grams of tritium per kilogram of LEU (g-T/kg-LEU). To date, the Nuclear Regulatory Commission (NRC) license has not been amended to accept a full load of TPBARs so the nominal tritium production has not yet been achieved. The alternatives currently loaded into the model include the three light water SMRs evaluated in TAMU senior projects including, mPower, Holtec and NuScale designs. Initial evaluations of tritium production in light water reactor (LWR) based SMRs using optimized loads TPBARs is on the order 0.02-0.06 grams of tritium per kilogram of LEU used. The TAMU students also chose to model tritium production in the GE-Hitachi SPRISM, a pooltype sodium fast reactor (SFR) utilizing a modified TPBAR type target. The team was unable to complete their project so no data is available. In order to include results from a fast reactor, the SRNL Technical Advisory Committee (TAC) ran a Monte Carlo N-Particle (MCNP) model of a basic SFR for comparison. A 600MWth core surrounded by a lithium blanket produced approximately 1,000 grams of tritium annually with a 13% enriched, 6 year core. This is similar results to a mid-1990’s study where the Fast Flux Test Facility (FFTF), a 400 MWth reactor at the Idaho National Laboratory (INL), could produce about 1,000 grams with an external lithium target. Normalized to the LWRs values, comparative tritium production for an SFR could be approximately 0.31 g-T/kg LEU.« less

A Methodology for Characterizing Potential Uranium Transport in Deep Geological Disposal Sites

NASA Astrophysics Data System (ADS)

Dittrich, T. M.; Reimus, P. W.

2013-12-01

In order to make safe and reasonable decisions about radioactive waste disposal in deep geologic sites, it is important to understand the fate and potential transport of long half-life transuranic radionuclides over a wide range of time and distance scales. The objective of this study was to evaluate and demonstrate new experimental methods for quantifying the potential for actinide transport in deep fractured crystalline rock formations. We selected a fractured/weathered granodiorite at the Grimsel Test Site (GTS) in Switzerland as a model system because field experiments involving uranium, as well as other actinides, have already been conducted. Working on this system provides a unique opportunity to compare lab experimental results with field-scale observations. Drilled rock cores and weathered fracture fill material (FFM) from the GTS were shipped to Los Alamos National Laboratory, characterized by x-ray diffraction and microscopy, and used in batch sorption/desorption and column breakthrough experiments. Uranium solutions were made by adding uranium to a synthetic Grimsel groundwater that matched the natural water chemistry found in the GTS groundwater. Batch and breakthrough experiments were conducted using solutions between pH 6.9 and 9.0. All column experiments were conducted using syringe pumps at low flow rate (<0.3 ml h-1) in small columns containing 5 g of material with pore volumes of 2-3 ml. These small columns allow rapid and economical evaluation of sorption/desorption behavior under flowing conditions (and in duplicate or triplicate). Solutions were switched to uranium-free synthetic Grimsel groundwater after equilibration in batch experiments or after near-steady uranium breakthrough occurred in column experiments. The measurement of uranium concentrations as a function of time under these conditions allowed interrogation of desorption rates which we believe control uranium fate and transport over long time and distance scales. Uranium transport was conservative and matched tritium breakthrough for pH 9.0; however, retardation increased when pH was reduced to 7.9 and 6.9. We are currently evaluating uranium adsorption/desorption rates as a function of water chemistry (initial focus on pH), with future testing planned to evaluate the influence of carbonate concentrations, flow rates, mineralogy, bentonite colloids and other actinides (e.g., Am). Figure 1. Uranium breakthrough results for (a) 6.5 μM U, (b) U-free solution, (c) flow rate increased from 0.3 to 0.6 mL h-1, (d) pH increased from 6.8 to 7.2, and (e) pH increased from 7.2 to 8.8.

Newport-Inglewood-Carlsbad-Coronado Bank Fault System Nearshore Southern California: Testing models for Quaternary deformation

NASA Astrophysics Data System (ADS)

Bennett, J. T.; Sorlien, C. C.; Cormier, M.; Bauer, R. L.

2011-12-01

The San Andreas fault system is distributed across hundreds of kilometers in southern California. This transform system includes offshore faults along the shelf, slope and basin- comprising part of the Inner California Continental Borderland. Previously, offshore faults have been interpreted as being discontinuous and striking parallel to the coast between Long Beach and San Diego. Our recent work, based on several thousand kilometers of deep-penetration industry multi-channel seismic reflection data (MCS) as well as high resolution U.S. Geological Survey MCS, indicates that many of the offshore faults are more geometrically continuous than previously reported. Stratigraphic interpretations of MCS profiles included the ca. 1.8 Ma Top Lower Pico, which was correlated from wells located offshore Long Beach (Sorlien et. al. 2010). Based on this age constraint, four younger (Late) Quaternary unconformities are interpreted through the slope and basin. The right-lateral Newport-Inglewood fault continues offshore near Newport Beach. We map a single fault for 25 kilometers that continues to the southeast along the base of the slope. There, the Newport-Inglewood fault splits into the San Mateo-Carlsbad fault, which is mapped for 55 kilometers along the base of the slope to a sharp bend. This bend is the northern end of a right step-over of 10 kilometers to the Descanso fault and about 17 km to the Coronado Bank fault. We map these faults for 50 kilometers as they continue over the Mexican border. Both the San Mateo - Carlsbad with the Newport-Inglewood fault and the Coronado Bank with the Descanso fault are paired faults that form flower structures (positive and negative, respectively) in cross section. Preliminary kinematic models indicate ~1km of right-lateral slip since ~1.8 Ma at the north end of the step-over. We are modeling the slip on the southern segment to test our hypothesis for a kinematically continuous right-lateral fault system. We are correlating four younger Quaternary unconformities across portions of these faults to test whether the post- ~1.8 Ma deformation continues into late Quaternary. This will provide critical information for a meaningful assessment of the seismic hazards facing Newport beach through metropolitan San Diego.

3D Geospatial Models for Visualization and Analysis of Groundwater Contamination at a Nuclear Materials Processing Facility

NASA Astrophysics Data System (ADS)

Stirewalt, G. L.; Shepherd, J. C.

2003-12-01

Analysis of hydrostratigraphy and uranium and nitrate contamination in groundwater at a former nuclear materials processing facility in Oklahoma were undertaken employing 3-dimensional (3D) geospatial modeling software. Models constructed played an important role in the regulatory decision process of the U.S. Nuclear Regulatory Commission (NRC) because they enabled visualization of temporal variations in contaminant concentrations and plume geometry. Three aquifer systems occur at the site, comprised of water-bearing fractured shales separated by indurated sandstone aquitards. The uppermost terrace groundwater system (TGWS) aquifer is composed of terrace and alluvial deposits and a basal shale. The shallow groundwater system (SGWS) aquifer is made up of three shale units and two sandstones. It is separated from the overlying TGWS and underlying deep groundwater system (DGWS) aquifer by sandstone aquitards. Spills of nitric acid solutions containing uranium and radioactive decay products around the main processing building (MPB), leakage from storage ponds west of the MPB, and leaching of radioactive materials from discarded equipment and waste containers contaminated both the TGWS and SGWS aquifers during facility operation between 1970 and 1993. Constructing 3D geospatial property models for analysis of groundwater contamination at the site involved use of EarthVision (EV), a 3D geospatial modeling software developed by Dynamic Graphics, Inc. of Alameda, CA. A viable 3D geohydrologic framework model was initially constructed so property data could be spatially located relative to subsurface geohydrologic units. The framework model contained three hydrostratigraphic zones equivalent to the TGWS, SGWS, and DGWS aquifers in which groundwater samples were collected, separated by two sandstone aquitards. Groundwater data collected in the three aquifer systems since 1991 indicated high concentrations of uranium (>10,000 micrograms/liter) and nitrate (> 500 milligrams/liter) around the MPB and elevated nitrate (> 2000 milligrams/ liter) around storage ponds. Vertical connectivity was suggested between the TGWS and SGWS, while the DGWS appeared relatively isolated from the overlying aquifers. Lateral movement of uranium was also suggested over time. For example, lateral migration in the TGWS is suggested along a shallow depression in the bedrock surface trending south-southwest from the southwest corner of the MPB. Another pathway atop the buried bedrock surface, trending west-northwest from the MPB and partially reflected by current surface topography, suggested lateral migration of nitrate in the SGWS. Lateral movement of nitrate in the SGWS was also indicated north, south, and west of the largest storage pond. Definition of contaminant plume movement over time is particularly important for assessing direction and rate of migration and the potential need for preventive measures to control contamination of groundwater outside facility property lines. The 3D geospatial property models proved invaluable for visualizing and analyzing variations in subsurface uranium and nitrate contamination in space and time within and between the three aquifers at the site. The models were an exceptional visualization tool for illustrating extent, volume, and quantitative amounts of uranium and nitrate contamination in the subsurface to regulatory decision-makers in regard to site decommissioning issues, including remediation concerns, providing a perspective not possible to achieve with traditional 2D maps. The geohydrologic framework model provides a conceptual model for consideration in flow and transport analyses.

A 26 million year gap in the central Arctic record at the greenhouse-icehouse transition: Looking for clues

USGS Publications Warehouse

Sangiorgi, Francesca; Brumsack, Hans-Juergen; Willard, Debra A.; Schouten, Stefan; Stickley, Catherine E.; O'Regan, Matthew; Reichart, Gert-Jan; Damste, Jaap S. Sinninghe; Brinkhuis, Henk

2008-01-01

The Cenozoic record of the Lomonosov Ridge (central Arctic Ocean) recovered during Integrated Ocean Drilling Program (IODP) Expedition 302 revealed an unexpected 26 Ma hiatus, separating middle Eocene (∼44.4 Ma) from lower Miocene sediments (∼18.2 Ma). To elucidate the nature of this unconformity, we performed a multiproxy palynological (dinoflagellate cysts, pollen, and spores), micropaleontological (siliceous microfossils), inorganic, and organic (Tetra Ether Index of lipids with 86 carbon atoms (TEX86) and Branched and Isoprenoid Tetraether (BIT)) geochemical analysis of the sediments from ∼5 m below to ∼7 m above the hiatus. Four main paleoenvironmental phases (A–D) are recognized in the sediments encompassing the unconformity, two below (A–B) and two above (C–D): (A) Below the hiatus, proxies show relatively warm temperatures, with Sea Surface Temperatures (TEX86‐derived SSTs) of about 8°C and high fresh to brackish water influence. (B) Approaching the hiatus, proxies indicate a cooling trend (TEX86‐derived SSTs of ∼5°C), increased freshwater influence, and progressive shoaling of the Lomonosov Ridge drilling site, located close to or at sea level. (C) The interval directly above the unconformity contains sparse reworked Cretaceous to Oligocene dinoflagellate cysts. Sediments were deposited in a relatively shallow, restricted marine environment. Proxies show the simultaneous influence of both fresh and marine waters, with alternating oxic and anoxic conditions. Pollen indicates a relatively cold climate. Intriguingly, TEX86‐derived SSTs are unexpectedly high, ∼15–19°C. Such warm surface waters may be partially explained by the ingression of warmer North Atlantic waters after the opening of the Fram Strait during the early Miocene. (D) Sediments of the uppermost interval indicate a phase of extreme oxic conditions, and a well‐ventilated environment, which occurred after the complete opening of the Fram Strait. Importantly, and in contrast with classical postrifting thermal subsidence models for passive margins, our data suggest that sediment erosion and/or nondeposition that generated the hiatus was likely due to a progressive shoaling of the Lomonosov Ridge. A shallow water setting both before and after the hiatus suggests that the Lomonosov Ridge remained at or near sea level for the duration of the gap in the sedimentary record. Interacting sea level changes and/or tectonic activity (possibly uplift) must be invoked as possible causes for such a long hiatus.

Genome-Based Models to Optimize In Situ Bioremediation of Uranium and Harvesting Electrical Energy from Waste Organic Matter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lovley, Derek R

2012-12-28

The goal of this research was to provide computational tools to predictively model the behavior of two microbial communities of direct relevance to Department of Energy interests: 1) the microbial community responsible for in situ bioremediation of uranium in contaminated subsurface environments; and 2) the microbial community capable of harvesting electricity from waste organic matter and renewable biomass. During this project the concept of microbial electrosynthesis, a novel form of artificial photosynthesis for the direct production of fuels and other organic commodities from carbon dioxide and water was also developed and research was expanded into this area as well.

Mineral transformation and biomass accumulation associated with uranium bioremediation at Rifle, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, L.; Steefel, C.I.; Williams, K.H.

2009-04-20

Injection of organic carbon into the subsurface as an electron donor for bioremediation of redox-sensitive contaminants like uranium often leads to mineral transformation and biomass accumulation, both of which can alter the flow field and potentially bioremediation efficacy. This work combines reactive transport modeling with a column experiment and field measurements to understand the biogeochemical processes and to quantify the biomass and mineral transformation/accumulation during a bioremediation experiment at a uranium contaminated site near Rifle, Colorado. We use the reactive transport model CrunchFlow to explicitly simulate microbial community dynamics of iron and sulfate reducers, and their impacts on reaction rates.more » The column experiment shows clear evidence of mineral precipitation, primarily in the form of calcite and iron monosulfide. At the field scale, reactive transport simulations suggest that the biogeochemical reactions occur mostly close to the injection wells where acetate concentrations are highest, with mineral precipitate and biomass accumulation reaching as high as 1.5% of the pore space. This work shows that reactive transport modeling coupled with field data can be an effective tool for quantitative estimation of mineral transformation and biomass accumulation, thus improving the design of bioremediation strategies.« less

Mineral transformation and biomass accumulation associated with uranium bioremediation at Rifle, Colorado.

PubMed

Li, Li; Steefel, Carl I; Williams, Kenneth H; Wilkins, Michael J; Hubbard, Susan S

2009-07-15

Injection of organic carbon into the subsurface as an electron donor for bioremediation of redox-sensitive contaminants like uranium often leads to mineral transformation and biomass accumulation, both of which can alter the flow field and potentially bioremediation efficacy. This work combines reactive transport modeling with a column experiment and field measurements to understand the biogeochemical processes and to quantify the biomass and mineral transformation/accumulation during a bioremediation experiment at a uranium contaminated site near Rifle, Colorado. We use the reactive transport model CrunchFlow to explicitly simulate microbial community dynamics of iron and sulfate reducers, and their impacts on reaction rates. The column experiment shows clear evidence of mineral precipitation, primarily in the form of calcite and iron monosulfide. At the field scale, reactive transport simulations suggest that the biogeochemical reactions occur mostly close to the injection wells where acetate concentrations are highest, with mineral precipitate and biomass accumulation reaching as high as 1.5% of the pore space. This work shows that reactive transport modeling coupled with field data can bean effective tool for quantitative estimation of mineral transformation and biomass accumulation, thus improving the design of bioremediation strategies.

Advanced fuels modeling: Evaluating the steady-state performance of carbide fuel in helium-cooled reactors using FRAPCON 3.4

NASA Astrophysics Data System (ADS)

Hallman, Luther, Jr.

Uranium carbide (UC) has long been considered a potential alternative to uranium dioxide (UO2) fuel, especially in the context of Gen IV gas-cooled reactors. It has shown promise because of its high uranium density, good irradiation stability, and especially high thermal conductivity. Despite its many benefits, UC is known to swell at a rate twice that of UO2. However, the swelling phenomenon is not well understood, and we are limited to a weak empirical understanding of the swelling mechanism. One suggested cladding for UC is silicon carbide (SiC), a ceramic that demonstrates a number of desirable properties. Among them are an increased corrosion resistance, high mechanical strength, and irradiation stability. However, with increased temperatures, SiC exhibits an extremely brittle nature. The brittle behavior of SiC is not fully understood and thus it is unknown how SiC would respond to the added stress of a swelling UC fuel. To better understand the interaction between these advanced materials, each has been implemented into FRAPCON, the preferred fuel performance code of the Nuclear Regulatory Commission (NRC); additionally, the material properties for a helium coolant have been incorporated. The implementation of UC within FRAPCON required the development of material models that described not only the thermophysical properties of UC, such as thermal conductivity and thermal expansion, but also models for the swelling, densification, and fission gas release associated with the fuel's irradiation behavior. This research is intended to supplement ongoing analysis of the performance and behavior of uranium carbide and silicon carbide in a helium-cooled reactor.

Post Audit of a Field Scale Reactive Transport Model of Uranium at a Former Mill Site

NASA Astrophysics Data System (ADS)

Curtis, G. P.

2015-12-01

Reactive transport of hexavalent uranium (U(VI)) in a shallow alluvial aquifer at a former uranium mill tailings site near Naturita CO has been monitored for nearly 30 years by the US Department of Energy and the US Geological Survey. Groundwater at the site has high concentrations of chloride, alkalinity and U(VI) as a owing to ore processing at the site from 1941 to 1974. We previously calibrated a multicomponent reactive transport model to data collected at the site from 1986 to 2001. A two dimensional nonreactive transport model used a uniform hydraulic conductivity which was estimated from observed chloride concentrations and tritium helium age dates. A reactive transport model for the 2km long site was developed by including an equilibrium U(VI) surface complexation model calibrated to laboratory data and calcite equilibrium. The calibrated model reproduced both nonreactive tracers as well as the observed U(VI), pH and alkalinity. Forward simulations for the period 2002-2015 conducted with the calibrated model predict significantly faster natural attenuation of U(VI) concentrations than has been observed by the persistent high U(VI) concentrations at the site. Alternative modeling approaches are being evaluating evaluated using recent data to determine if the persistence can be explained by multirate mass transfer models developed from experimental observations at the column scale(~0.2m), the laboratory tank scale (~2m), the field tracer test scale (~1-4m) or geophysical observation scale (~1-5m). Results of this comparison should provide insight into the persistence of U(VI) plumes and improved management options.

PRODUCTION OF URANIUM METAL BY CARBON REDUCTION

DOEpatents

Holden, R.B.; Powers, R.M.; Blaber, O.J.

1959-09-22

The preparation of uranium metal by the carbon reduction of an oxide of uranium is described. In a preferred embodiment of the invention a charge composed of carbon and uranium oxide is heated to a solid mass after which it is further heated under vacuum to a temperature of about 2000 deg C to produce a fused uranium metal. Slowly ccoling the fused mass produces a dendritic structure of uranium carbide in uranium metal. Reacting the solidified charge with deionized water hydrolyzes the uranium carbide to finely divide uranium dioxide which can be separated from the coarser uranium metal by ordinary filtration methods.

Contaminant Leach Testing of Hanford Tank 241-C-104 Residual Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cantrell, Kirk J.; Snyder, Michelle M.V.; Wang, Guohui

2015-07-01

Leach testing of Tank C-104 residual waste was completed using batch and column experiments. Tank C-104 residual waste contains exceptionally high concentrations of uranium (i.e., as high as 115 mg/g or 11.5 wt.%). This study was conducted to provide data to develop contaminant release models for Tank C-104 residual waste and Tank C-104 residual waste that has been treated with lime to transform uranium in the waste to a highly insoluble calcium uranate (CaUO4) or similar phase. Three column leaching cases were investigated. In the first case, C-104 residual waste was leached with deionized water. In the second case, crushedmore » grout was added to the column so that deionized water contacted the grout prior to contacting the waste. In the third case, lime was mixed in with the grout. Results of the column experiments demonstrate that addition of lime dramatically reduces the leachability of uranium from Tank C-104 residual waste. Initial indications suggest that CaUO4 or a similar highly insoluble calcium rich uranium phase forms as a result of the lime addition. Additional work is needed to definitively identify the uranium phases that occur in the as received waste and the waste after the lime treatment.« less

Solubility classification of airborne uranium products collected at the perimeter of the Allied Chemical Plant, Metropolis, Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalkwarf, D.R.

1980-05-01

Airborne uranium products were collected at the perimeter of the uranium-conversion plant operated by the Allied Chemical Corporation at Metropolis, Illinois, and the dissolution rates of these products were classified in terms of the ICRP Task Group Lung Model. Assignments were based on measurements of the dissolution half-times exhibited by uranium components of the dust samples as they dissolved in simulated lung fluid at 37/sup 0/C. Based on three trials, the dissolution behavior of dust with aerodynamic equivalent diameter (AED) less than 5.5 ..mu..m and collected nearest the closest residence to the plant was classified 0.40 D, 0.60 Y. Basedmore » on two trials, the dissolution behavior of dust with AED greater than 5.5 ..mu..m and collected at this location was classified 0.37 D, 0.63 Y. Based on one trial, the dissolution behavior of dust with AED less than 5.5 ..mu..m and collected at a location on the opposite side of the plant was classified 0.68 D, 0.32 Y. There was some evidence for adsorption of dissolved uranium onto other dust components during dissolution, and preliminary dissolution trials are recommended for future samples in order to optimize the fluid replacement schedule.« less

Reduction of uranium by cytochrome c3 of Desulfovibrio vulgaris

USGS Publications Warehouse

Lovley, D.R.; Widman, P.K.; Woodward, J.C.; Phillips, E.J.P.

1993-01-01

The mechanism for U(VI) reduction by Desulfovibrio vulgaris (Hildenborough) was investigated. The H2-dependent U(VI) reductase activity in the soluble fraction of the cells was lost when the soluble fraction was passed over a cationic exchange column which extracted cytochrome c3. Addition of cytochrome c3 back to the soluble fraction that had been passed over the cationic exchange column restored the U(VI)-reducing capacity. Reduced cytochrome c3 was oxidized by U(VI), as was a c-type cytochrome(s) in whole-cell suspensions. When cytochrome c3 was combined with hydrogenase, its physiological electron donor, U(VI) was reduced in the presence of H2. Hydrogenase alone could not reduce U(VI). Rapid U(VI) reduction was followed by a subsequent slow precipitation of the U(IV) mineral uraninite. Cytochrome c3 reduced U(VI) in a uranium-contaminated surface water and groundwater. Cytochrome c3 provides the first enzyme model for the reduction and biomineralization of uranium in sedimentary environments. Furthermore, the finding that cytochrome c3 can catalyze the reductive precipitation of uranium may aid in the development of fixed-enzyme reactors and/or organisms with enhanced U(VI)-reducing capacity for the bioremediation of uranium- contaminated waters and waste streams.

Quantifying Uranium Isotope Ratios Using Resonance Ionization Mass Spectrometry: The Influence of Laser Parameters on Relative Ionization Probability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isselhardt, Brett H.

2011-09-01

Resonance Ionization Mass Spectrometry (RIMS) has been developed as a method to measure relative uranium isotope abundances. In this approach, RIMS is used as an element-selective ionization process to provide a distinction between uranium atoms and potential isobars without the aid of chemical purification and separation. We explore the laser parameters critical to the ionization process and their effects on the measured isotope ratio. Specifically, the use of broad bandwidth lasers with automated feedback control of wavelength was applied to the measurement of 235U/ 238U ratios to decrease laser-induced isotopic fractionation. By broadening the bandwidth of the first laser inmore » a 3-color, 3-photon ionization process from a bandwidth of 1.8 GHz to about 10 GHz, the variation in sequential relative isotope abundance measurements decreased from >10% to less than 0.5%. This procedure was demonstrated for the direct interrogation of uranium oxide targets with essentially no sample preparation. A rate equation model for predicting the relative ionization probability has been developed to study the effect of variation in laser parameters on the measured isotope ratio. This work demonstrates that RIMS can be used for the robust measurement of uranium isotope ratios.« less

Model of a Generic Natural Uranium Conversion Plant ? Suggested Measures to Strengthen International Safeguards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raffo-Caiado, Ana Claudia; Begovich, John M; Ferrada, Juan J

This is the final report that closed a joint collaboration effort between DOE and the National Nuclear Energy Commission of Brazil (CNEN). In 2005, DOE and CNEN started a collaborative effort to evaluate measures that can strengthen the effectiveness of international safeguards at a natural uranium conversion plant (NUCP). The work was performed by DOE s Oak Ridge National Laboratory and CNEN. A generic model of a NUCP was developed and typical processing steps were defined. Advanced instrumentation and techniques for verification purposes were identified and investigated. The scope of the work was triggered by the International Atomic Energy Agencymore » s 2003 revised policy concerning the starting point of safeguards at uranium conversion facilities. Prior to this policy only the final products of the uranium conversion plant were considered to be of composition and purity suitable for use in the nuclear fuel cycle and therefore, subject to the IAEA safeguards control. DOE and CNEN have explored options for implementing the IAEA policy, although Brazil understands that the new policy established by the IAEA is beyond the framework of the Quadripartite Agreement of which it is one of the parties, together with Argentina, the Brazilian-Argentine Agency for Accounting and Control of Nuclear Materials (ABACC) and the IAEA. Two technical papers on this subject were published at the 2005 and 2008 INMM Annual Meetings.« less

Quantifying Differences in the Impact of Variable Chemistry on Equilibrium Uranium(VI) Adsorption Properties of Aquifer Sediments

PubMed Central

2011-01-01

Uranium adsorption–desorption on sediment samples collected from the Hanford 300-Area, Richland, WA varied extensively over a range of field-relevant chemical conditions, complicating assessment of possible differences in equilibrium adsorption properties. Adsorption equilibrium was achieved in 500–1000 h although dissolved uranium concentrations increased over thousands of hours owing to changes in aqueous chemical composition driven by sediment-water reactions. A nonelectrostatic surface complexation reaction, >SOH + UO22+ + 2CO32- = >SOUO2(CO3HCO3)2–, provided the best fit to experimental data for each sediment sample resulting in a range of conditional equilibrium constants (logKc) from 21.49 to 21.76. Potential differences in uranium adsorption properties could be assessed in plots based on the generalized mass-action expressions yielding linear trends displaced vertically by differences in logKc values. Using this approach, logKc values for seven sediment samples were not significantly different. However, a significant difference in adsorption properties between one sediment sample and the fines (<0.063 mm) of another could be demonstrated despite the fines requiring a different reaction stoichiometry. Estimates of logKc uncertainty were improved by capturing all data points within experimental errors. The mass-action expression plots demonstrate that applying models outside the range of conditions used in model calibration greatly increases potential errors. PMID:21923109

Quantifying differences in the impact of variable chemistry on equilibrium Uranium(VI) adsorption properties of aquifer sediments.

PubMed

Stoliker, Deborah L; Kent, Douglas B; Zachara, John M

2011-10-15

Uranium adsorption-desorption on sediment samples collected from the Hanford 300-Area, Richland, WA varied extensively over a range of field-relevant chemical conditions, complicating assessment of possible differences in equilibrium adsorption properties. Adsorption equilibrium was achieved in 500-1000 h although dissolved uranium concentrations increased over thousands of hours owing to changes in aqueous chemical composition driven by sediment-water reactions. A nonelectrostatic surface complexation reaction, >SOH + UO₂²⁺ + 2CO₃²⁻ = >SOUO₂(CO₃HCO₃)²⁻, provided the best fit to experimental data for each sediment sample resulting in a range of conditional equilibrium constants (logK(c)) from 21.49 to 21.76. Potential differences in uranium adsorption properties could be assessed in plots based on the generalized mass-action expressions yielding linear trends displaced vertically by differences in logK(c) values. Using this approach, logK(c) values for seven sediment samples were not significantly different. However, a significant difference in adsorption properties between one sediment sample and the fines (< 0.063 mm) of another could be demonstrated despite the fines requiring a different reaction stoichiometry. Estimates of logK(c) uncertainty were improved by capturing all data points within experimental errors. The mass-action expression plots demonstrate that applying models outside the range of conditions used in model calibration greatly increases potential errors.

Model for detection and assessment of abiotic stress caused by uranium mining in European Black Pine landscapes

NASA Astrophysics Data System (ADS)

Filchev, Lachezar; Roumenina, Eugenia

2013-10-01

The article presents the results obtained from a study for detection and assessment of abiotic stress through pollution with heavy metals, metalloids, and natural radionuclides in European Black Pine (Pinus nigra L.) forests caused by uranium mining using ground-based biogeochemical, biophysical, and field spectrometry data. The forests are located on a territory subject to underground and open uranium mining. An operational model of the study is proposed. The areas subject to technogeochemical load are outlined based on the aggregate pollution index Zc. Laboratory and field spectrometry data were used to detect the signals of abiotic stress at pixel level. The methods used for determination of stressed and unstressed black pine forests are: four vegetation indices (TCARI, MCARI, MTVI 2, and PRI 1) for stress detection, and the position, depth, asymmetry, and shift of the red-edge. Based on the "blue shift" and the depth and position of the red-edge, registered by the laboratory analysis and field spectral reflectance, it is established that coniferous forests subject to abiotic stress show an increase in total chlorophyll content and carotene. It has been found that the vegetation indices MTVI 2 and PRI 1, as well as the combination of vegetation indices and pigments may be used as a direct indicator of abiotic stress in coniferous forests caused by uranium mining.

STRIPPING OF URANIUM FROM ORGANIC EXTRACTANTS

DOEpatents

Crouse, D.J. Jr.

1962-09-01

A liquid-liquid extraction method is given for recovering uranium values from uranium-containing solutions. Uranium is removed from a uranium-containing organic solution by contacting said organic solution with an aqueous ammonium carbonate solution substantially saturated in uranium values. A uranium- containing precipitate is thereby formed which is separated from the organic and aqueous phases. Uranium values are recovered from this separated precipitate. (AE C)

Process for electroslag refining of uranium and uranium alloys

DOEpatents

Lewis, P.S. Jr.; Agee, W.A.; Bullock, J.S. IV; Condon, J.B.

1975-07-22

A process is described for electroslag refining of uranium and uranium alloys wherein molten uranium and uranium alloys are melted in a molten layer of a fluoride slag containing up to about 8 weight percent calcium metal. The calcium metal reduces oxides in the uranium and uranium alloys to provide them with an oxygen content of less than 100 parts per million. (auth)

Detection of depleted uranium in urine of veterans from the 1991 Gulf War.

PubMed

Gwiazda, R H; Squibb, K; McDiarmid, M; Smith, D

2004-01-01

American soldiers involved in "friendly fire" accidents during the 1991 Gulf War were injured with depleted-uranium-containing fragments or possibly exposed to depleted uranium via other routes such as inhalation, ingestion, and/or wound contamination. To evaluate the presence of depleted uranium in these soldiers eight years later, the uranium concentration and depleted uranium content of urine samples were determined by inductively coupled plasma mass spectrometry in (a) depleted uranium exposed soldiers with embedded shrapnel, (b) depleted uranium exposed soldiers with no shrapnel, and (c) a reference group of deployed soldiers not involved in the friendly fire incidents. Uranium isotopic ratios measured in many urine samples injected directly into the inductively coupled plasma mass spectrometer and analyzed at a mass resolution m/delta m of 300 appeared enriched in 235U with respect to natural abundance (0.72%) due to the presence of an interference of a polyatomic molecule of mass 234.81 amu that was resolved at a mass resolution m/delta m of 4,000. The 235U abundance measured on uranium separated from these urines by anion exchange chromatography was clearly natural or depleted. Urine uranium concentrations of soldiers with shrapnel were higher than those of the two other groups, and 16 out of 17 soldiers with shrapnel had detectable depleted uranium in their urine. In depleted uranium exposed soldiers with no shrapnel, depleted uranium was detected in urine samples of 10 out of 28 soldiers. The median uranium concentration of urines with depleted uranium from soldiers without shrapnel was significantly higher than in urines with no depleted uranium, though substantial overlap in urine uranium concentrations existed between the two groups. Accordingly, assessment of depleted uranium exposure using urine must rely on uranium isotopic analyses, since urine uranium concentration is not an unequivocal indicator of depleted uranium presence in soldiers with no embedded shrapnel.

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 3 2013-07-01 2013-07-01 false Uranium feed; natural uranium feed... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The...

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 3 2012-07-01 2012-07-01 false Uranium feed; natural uranium feed... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The...

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance:Treasury 3 2014-07-01 2014-07-01 false Uranium feed; natural uranium feed... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The...

Mio-Pliocene to Pleistocene paleotopographic evolution of Brittany (France) from a sequence stratigraphic analysis: relative influence of tectonics and climate

NASA Astrophysics Data System (ADS)

Brault, N.; Bourquin, S.; Guillocheau, F.; Dabard, M.-P.; Bonnet, S.; Courville, P.; Estéoule-Choux, J.; Stepanoff, F.

2004-01-01

The Mio-Pliocene in Western Europe is a period of major climatic and tectonic change with important topographic consequences. The aim of this paper is to reconstruct these topographic changes (based on sedimentological analysis and sequence stratigraphy) for the Armorican Massif (western France) and to discuss their significance. The Mio-Pliocene sands of the Armorican Massif (Red Sands) are mainly preserved in paleovalleys and are characterized by extensive fluvial sheetflood deposits with low-preservation and by-pass facies. This sedimentological study shows that the Red Sands correspond to three main sedimentary environments: fluvial (alluvial fan, low-sinuosity rivers and braided rivers), estuarine and some rare open marine deposits (marine bioclastic sands: "faluns" of French authors). Two orders of sequences have been correlated across Brittany with one or two minor A/ S cycles comprised within the retrogradational trend of a major cycle. The unconformity at the base of the lower cycle is more marked than the unconformity observed at the top, which corresponds to a re-incision of the paleovalley network. A comparison of the results of the sequence stratigraphy analysis with eustatic variations and tectonic events during the Mio-Pliocene allows (1) to discuss their influence on the evolution of the Armorican Massif and (2) to compare the stratigraphic record with other west-European basins. The unconformity observed at the base of the first minor cycle may be attributed to Serravallian-Tortonian tectonic activity and/or eustatic fall, and the unconformity of the second minor cycle may be attributed to Late Tortonian-Early Messinian tectonic activity. The earlier unconformity is coeval with the development of a "smooth" paleovalley network compared to the jagged present-day relief. A single episode of Mio-Pliocene deformation recorded in Brittany may be dated as Zanclean, thus explaining the lack of the maximum flooding surface except in isolated areas. From this study, five paleogeographic maps were drawn up also indicating paleocurrent directions: three maps for the lower cycle (Tortonian retrogradational trend, Late Tortonian to Early Messinian maximum flooding surface and Messinian progradational trend) and two for the upper cycle (Pliocene retrogradational trend and Piacenzian maximum flooding surface). These maps show (1) the variations of paleocurrent directions during the Mio-Pliocene, (2) the extent of estuarine environments during the maximum flooding intervals and (3) a paleodrainage watershed oriented NNW-SSE following the regional Quessoy/Nort-sur-Erdre Fault during the retrogradational trend of the upper cycle and possibly during the progradational trend of the lower cycle. The present-day morphology of the Armorican Massif is characterized by (1) incised valleys and jagged topography, in contrast with the "smooth" morphology described for Mio-Pliocene times and (2) a main East-West drainage watershed, located to the north, separating rivers flowing towards the English Channel from rivers flowing towards the Atlantic Ocean. The Mio-Pliocene/Pleistocene paleotopographic changes seem to be controlled by climatic effects. These can be related to the change in runoff associated with warmer and wetter conditions during the Mio-Pliocene, which control the river discharge and lead to the development of extensive fluvial sheetflood deposits. Tectonic or eustatic factors exert a second-order control.

Reactive transport modeling of uranium 238 and radium 226 in groundwater of the Königstein uranium mine, Germany

NASA Astrophysics Data System (ADS)

Nitzsche, O.; Merkel, B.

Knowledge of the transport behavior of radionuclides in groundwater is needed for both groundwater protection and remediation of abandoned uranium mines and milling sites. Dispersion, diffusion, mixing, recharge to the aquifer, and chemical interactions, as well as radioactive decay, should be taken into account to obtain reliable predictions on transport of primordial nuclides in groundwater. This paper demonstrates the need for carrying out rehabilitation strategies before closure of the Königstein in-situ leaching uranium mine near Dresden, Germany. Column experiments on drilling cores with uranium-enriched tap water provided data about the exchange behavior of uranium. Uranium breakthrough was observed after more than 20 pore volumes. This strong retardation is due to the exchange of positively charged uranium ions. The code TReAC is a 1-D, 2-D, and 3-D reactive transport code that was modified to take into account the radioactive decay of uranium and the most important daughter nuclides, and to include double-porosity flow. TReAC satisfactorily simulated the breakthrough curves of the column experiments and provided a first approximation of exchange parameters. Groundwater flow in the region of the Königstein mine was simulated using the FLOWPATH code. Reactive transport behavior was simulated with TReAC in one dimension along a 6000-m path line. Results show that uranium migration is relatively slow, but that due to decay of uranium, the concentration of radium along the flow path increases. Results are highly sensitive to the influence of double-porosity flow. Résumé La protection des eaux souterraines et la restauration des sites miniers et de prétraitement d'uranium abandonnés nécessitent de connaître le comportement des radionucléides au cours de leur transport dans les eaux souterraines. La dispersion, la diffusion, le mélange, la recharge de l'aquifère et les interactions chimiques, de même que la décroissance radioactive, doivent être prises en compte pour obtenir des prédictions fiables concernant le transport des nucléides primaires dans les eaux souterraines. Ce papier montre la nécessité d'établir des stratégies de réhabilitation avant la fermeture de la mine d'uranium de Knigstein, près de Dresde (Allemagne). Des expériences de lessivage en colonne sur des carottes avec de l'eau enrichie en uranium fournissent des données sur le comportement de l'échange de l'uranium. La restitution de l'uranium a été observée après un lessivage par un volume supérieur à 20 fois celui des pores. Ce fort retard est dûà l'échange d'ions uranium positifs. Le code TReAC est un code de transport réactif en 1D, 2D et 3D, qui a été modifié pour prendre en compte la décroissance radioactive de l'uranium et les principaux nucléides descendants, et pour introduire l'écoulement dans un milieu à double porosité. TReAC a simulé de façon satisfaisante les courbes de restitution des expériences sur colonne et a fourni une première approche des paramètres de l'échange. L'écoulement souterrain dans la région de la mine de Knigstein a été simulé au moyen du code FLOWPATH. Le comportement du transport réactif a été simulé avec TReAC en une dimension, le long d'un axe d'écoulement long de 6000 m. Les résultats montrent que la migration de l'uranium est relativement lente ; mais du fait de la décroissance radioactive de l'uranium, la concentration en radium le long de cet axe augmente. Les résultats sont très sensibles à l'influence de l'écoulement en milieu à double porosité.

Process for electrolytically preparing uranium metal

DOEpatents

Haas, Paul A.

1989-01-01

A process for making uranium metal from uranium oxide by first fluorinating uranium oxide to form uranium tetrafluoride and next electrolytically reducing the uranium tetrafluoride with a carbon anode to form uranium metal and CF.sub.4. The CF.sub.4 is reused in the fluorination reaction rather than being disposed of as a hazardous waste.

Process for electrolytically preparing uranium metal

DOEpatents

Haas, Paul A.

1989-08-01

A process for making uranium metal from uranium oxide by first fluorinating uranium oxide to form uranium tetrafluoride and next electrolytically reducing the uranium tetrafluoride with a carbon anode to form uranium metal and CF.sub.4. The CF.sub.4 is reused in the fluorination reaction rather than being disposed of as a hazardous waste.

Decontamination of uranium-contaminated waste oil using supercritical fluid and nitric acid.

PubMed

Sung, Jinhyun; Kim, Jungsoo; Lee, Youngbae; Seol, Jeunggun; Ryu, Jaebong; Park, Kwangheon

2011-07-01

The waste oil used in nuclear fuel processing is contaminated with uranium because of its contact with materials or environments containing uranium. Under current law, waste oil that has been contaminated with uranium is very difficult to dispose of at a radioactive waste disposal site. To dispose of the uranium-contaminated waste oil, the uranium was separated from the contaminated waste oil. Supercritical R-22 is an excellent solvent for extracting clean oil from uranium-contaminated waste oil. The critical temperature of R-22 is 96.15 °C and the critical pressure is 49.9 bar. In this study, a process to remove uranium from the uranium-contaminated waste oil using supercritical R-22 was developed. The waste oil has a small amount of additives containing N, S or P, such as amines, dithiocarbamates and dialkyldithiophosphates. It seems that these organic additives form uranium-combined compounds. For this reason, dissolution of uranium from the uranium-combined compounds using nitric acid was needed. The efficiency of the removal of uranium from the uranium-contaminated waste oil using supercritical R-22 extraction and nitric acid treatment was determined.

Studies of the kinetics and mechanism of the oxidation of uranium by dry and moist air A model for determining the oxidation rate over a wide range of temperatures and water vapour pressures

NASA Astrophysics Data System (ADS)

McGillivray, G. W.; Geeson, D. A.; Greenwood, R. C.

1994-01-01

The rate of oxidation of uranium metal by moist air has been measured at temperatures from 115 to 350°C and water vapour pressures from 0 to 47 kPa (350 Torr). From this and from previously reported data, a model has been developed which allows the rate of uranium oxidation to be calculated at any particular combination of temperature and water vapour pressure of interest, in the range 0-350°C and 0-101.3 kPa (760 Torr). The model is based on the assumption that the surface concentration of water determines the rate of reaction and that the adsorption of water onto the oxide follows a Langmuir type isotherm. Theoretical plots of rate as a function of water vapour pressure and Arrhenius plots derived from the model have been shown to be in good agreement with experimental data. The model assumes separate contributions to the overall observed rate from oxygen and water vapour. Surface studies have been carried out using SIMS (secondary ion mass spectrometry). Depth profiling of the oxide produced by isotopically labelled reagents ( 18O 2 and H 218O), has shown that oxygen from both reactants is incorporated into the oxide layer in the ratio predicted by the kinetic model. This supports a mechanism in which oxygen and water vapour produce separate diffusing species (possibly O 2- and OH -).

Diffusive gradient in thin FILMS (DGT) compared with soil solution and labile uranium fraction for predicting uranium bioavailability to ryegrass.

PubMed

Duquène, L; Vandenhove, H; Tack, F; Van Hees, M; Wannijn, J

2010-02-01

The usefulness of uranium concentration in soil solution or recovered by selective extraction as unequivocal bioavailability indices for uranium uptake by plants is still unclear. The aim of the present study was to test if the uranium concentration measured by the diffusive gradient in thin films (DGT) technique is a relevant substitute for plant uranium availability in comparison to uranium concentration in the soil solution or uranium recovered by ammonium acetate. Ryegrass (Lolium perenne L. var. Melvina) is grown in greenhouse on a range of uranium spiked soils. The DGT-recovered uranium concentration (C(DGT)) was correlated with uranium concentration in the soil solution or with uranium recovered by ammonium acetate extraction. Plant uptake was better predicted by the summed soil solution concentrations of UO(2)(2+), uranyl carbonate complexes and UO(2)PO(4)(-). The DGT technique did not provide significant advantages over conventional methods to predict uranium uptake by plants. Copyright 2009 Elsevier Ltd. All rights reserved.

Digital outcrop model of stratigraphy and breccias of the southern Franklin Mountains, El Paso, Texas

USGS Publications Warehouse

Bellian, Jerome A.; Kerans, Charles; Repetski, John E.; Derby, James R.; Fritz, R.D.; Longacre, S.A.; Morgan, W.A.; Sternbach, C.A.

2012-01-01

The breccias of the SFM were previously described as the result of collapsed paleocaves that formed during subaerial exposure related to the Sauk-Tippecanoe unconformity. A new approach in this work uses traditional field mapping combined with high-resolution (1-m [3.3-ft] point spacing) airborne light detection and ranging (LIDAR) data over 24 km2 (9 mi2) to map breccia and relevant stratal surfaces. Airborne LIDAR data were used to create a digital outcrop model of the SFM from which a detailed (1:2000 scale) geologic map was created. The geologic map includes formation, fault, and breccia contacts. The digital outcrop model was used to interpret three-dimensional spatial relationships of breccia bodies with respect to the current understanding of the tectonic and stratigraphic evolution of the SFM. The data presented here are used to discuss potential stratigraphic, temporal, and tectonic controls on the formation of caves within the study area that eventually collapsed to form the breccias currently exposed in outcrop.

Occurrence of Uranium and 222Radon in Glacial and Bedrock Aquifers in the Northern United States, 1993-2003

USGS Publications Warehouse

Ayotte, Joseph D.; Flanagan, Sarah M.; Morrow, William S.

2007-01-01

Water-quality data collected from 1,426 wells during 1993-2003 as part of the U.S. Geological Survey National Water-Quality Assessment (NAWQA) program were evaluated to characterize the water quality in glacial and bedrock aquifers of the northern United States. One of the goals of the NAWQA program is to synthesize data from individual studies across the United States to gain regional- and national-scale information about the behavior of contaminants. This study focused on the regional occurrence and distribution of uranium and 222radon in ground water in the glacial aquifer system of the United States as well as in the Cambrian-Ordovician and the New York and New England crystalline aquifer systems that underlie the glacial aquifer system. The occurrence of uranium and 222radon in ground water has long been a concern throughout the United States. In the glacial aquifers, as well as the Cambrian-Ordovician and the New York and New England crystalline aquifer systems of the United States, concentrations of uranium and 222radon were highly variable. High concentrations of uranium and 222radon affect ground water used for drinking water and for agriculture. A combination of information or data on (1) national-scale ground-water regions, (2) regional-scale glacial depositional models, (3) regional-scale geology, and (4) national-scale terrestrial gamma-ray emissions were used to confirm and(or) refine the regions used in the analysis of the water-chemistry data. Significant differences in the occurrence of uranium and 222radon, based primarily on geologic information were observed and used in this report. In general, uranium was highest in the Columbia Plateau glacial, West-Central glacial, and the New York and New England crystalline aquifer groups (75th percentile concentrations of 22.3, 7.7, and 2.9 micrograms per liter (ug/L), respectively). In the Columbia Plateau glacial and the West-Central glacial aquifer groups, more than 10 percent of wells sampled had concentrations of uranium that exceeded the U.S. Environmental Protection Agency (USEPA) Maximum Contaminant Level of 30 ug/L; in the New York and New England crystalline aquifer group, 4 percent exceeded 30 ug/L. Ground-water samples with high concentrations of uranium were commonly linked to geologic sources rich in uranium. In eight of nine aquifer groups defined for this study, concentrations of uranium correlated significantly with concentrations of sulfate in ground water (Spearman's rho = 0.20 to 0.56; p < 0.05). In the Columbia Plateau, glacial aquifers were derived in part from basaltic lava flows, some felsic volcanic rocks, and some paleo-lake bed materials that may be rich in uranium. In the Columbia Plateau and West-Central glacial aquifer groups, uranium correlated with total dissolved solids, bicarbonate, boron, lithium, selenium, and strontium. In the West-Central glacial aquifer group, rocks such as Cretaceous marine shales, which are abundant in uranium, probably contribute to the high concentrations in ground water; in the southern part of this group, which extends into Nebraska, the glacial or glacial-related sediment may be interbedded with uranium-rich materials that originated to the north and west and in the Rocky Mountains. In New England, crystalline bedrock that is granitic, such as two-mica granites, as well as other high-grade metamorphic rocks, has abundant uranium that is soluble in the predominantly oxic to sub-oxic geochemical conditions. This appears to contribute to high uranium concentrations in ground water. The highest 222radon concentrations were present in samples from wells completed in the New York and New England crystalline aquifer group; the median value (2,122 picocurries per liter (pCi/L)) was about 10 times the median values of all other aquifer groups. More than 25 percent of the samples from the New York and New England crystalline aquifer group wells had 222radon concentrations that exceeded the USEPA Alternative

Field-scale and wellbore modeling of compaction-induced casing failures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hilbert, L.B. Jr.; Gwinn, R.L.; Moroney, T.A.

1999-06-01

Presented in this paper are the results and verification of field- and wellbore-scale large deformation, elasto-plastic, geomechanical finite element models of reservoir compaction and associated casing damage. The models were developed as part of a multidisciplinary team project to reduce the number of costly well failures in the diatomite reservoir of the South Belridge Field near Bakersfield, California. Reservoir compaction of high porosity diatomite rock induces localized shearing deformations on horizontal weak-rock layers and geologic unconformities. The localized shearing deformations result in casing damage or failure. Two-dimensional, field-scale finite element models were used to develop relationships between field operations, surfacemore » subsidence, and shear-induced casing damage. Pore pressures were computed for eighteen years of simulated production and water injection, using a three-dimensional reservoir simulator. The pore pressures were input to the two-dimensional geomechanical field-scale model. Frictional contact surfaces were used to model localized shear deformations. To capture the complex casing-cement-rock interaction that governs casing damage and failure, three-dimensional models of a wellbore were constructed, including a frictional sliding surface to model localized shear deformation. Calculations were compared to field data for verification of the models.« less

Molecular Simulations of the Diffusion of Uranyl Carbonate Species in Nanosized Mineral Fractures

NASA Astrophysics Data System (ADS)

Kerisit, S.; Liu, C.

2010-12-01

Uranium is a major groundwater contaminant at uranium processing and mining sites as a result of intentional and accidental discharges of uranium-containing waste products into subsurface environments. Recent characterization has shown that uranium preferentially associates with intragrain and intra-aggregate domains in some of the uranium-contaminated sediments collected from the US Department of Energy Hanford Site [1, 2]. In these sediments, uranium existed as precipitated and/or adsorbed phases in grain micropores with nano- to microscale sizes. Desorption and diffusion characterization studies and continuum-scale modeling indicated that ion diffusion in the microfractures is a major mechanism that led to preferential uranium concentration in the microfracture regions and will control the future mobility of uranium in the subsurface sediments [1, 3-4]. However, the diffusion properties of uranyl species in the intragrain regions, especially at the solid-liquid interface, are still poorly understood. Therefore, a general aim of this work is to provide atomic-level insights into the contribution of microscopic surface effects to the slow diffusion process of uranyl species in porous media with nano- to microsized fractures. In this presentation, we will first present molecular dynamics (MD) simulations of feldspar-water interfaces to investigate their interfacial structure and dynamics and establish a theoretical framework for subsequent simulations of water and ion diffusion at these interfaces [5]. We will then report on MD simulations carried out to probe the effects of confinement and of the presence of the mineral surface on the diffusion of water and electrolyte ions in nanosized feldspar fractures [6]. Several properties of the mineral-water interface were varied, such as the fracture width, the ionic strength of the contacting solution, and the surface charge. Our calculations reveal a 2.0-2.5 nm interfacial region within which the diffusion properties of water and that of the electrolyte ions differ significantly from those in bulk aqueous solutions. We will then present MD simulations of the diffusion of a series of alkaline-earth uranyl carbonate species in aqueous solutions [7]. The MD simulations show that the alkaline-earth uranyl carbonate complexes have distinct water exchange dynamics, which could lead to different reactivities. Finally, we will present recent results on the diffusion and adsorption of uranyl carbonate species in intragrain micropores, modeled with the feldspar-water interfaces mentioned in the above, to help interpret the diffusion behavior of uranium in contaminated sediments. [1] Liu C. et al. Geochim. Cosmochim. Acta 68 4519 (2004) [2] McKinley J. P. et al. Geochim. Cosmochim. Acta 70 1873 (2006) [3] Liu C. et al. Water Resour. Res. 42 W12420 (2006) [4] Ilton E. S. et al. Environ. Sci. Technol. 42 1565 (2009) [5] Kerisit S. et al. Geochim. Cosmochim. Acta 72 1481 (2008) [6] Kerisit S. and Liu C. Environ. Sci. Technol. 43 777 (2009) [7] Kerisit S. and Liu C. Geochim. Cosmochim. Acta 74 4937 (2010)

Biothems: Sequence stratigraphic units and their implications for regional tectono-stratigraphic interpretations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lane, H.R.; Frye, M.W.; Couples, G.D.

1992-01-01

Biothems are regional wedge- or lens-shaped bodies of strata that are bounded shelfward or cratonward by paleontologically recognizable unconformities; generally thicken on marine shelves, where they are typically conformable with underlying and overlying biothems; are commonly thinner or represent starved sequences further basinward; and in their most basinward extent, are either bounded by biostratigraphically recognizable unconformities or are conformable with underlying and overlying biothems. As recognized to date, biothems have a logical distribution of faunal and floral components, as well as facies groupings that represent internally consistent and logical sequences of depositional environments. A west-to-east transect within the North Americanmore » Mississippian System which extends from the Basin and Range Province, across the Transcontinental Arch (TA), into the Anadarko Basin, was constructed to demonstrate the regional distribution and tectono-stratigraphic significance of biothems relative to the axis of the TA. The relationships portrayed on the transect, tied to an understanding of North American Mississippian paleogeography, imply that biothems deposited during relative highstand events on one flank of the TA are time-equivalent to biothems deposited during relative lowstand events on the opposite flank of the TA. This distribution is interpreted to have been controlled by intraplate tectonic events that formed piano key basins along the flanks of the TA. The spatial patterns of these basins are not consistent with published models of basin evolution. A further conclusion is that the lack of coincident, transgressive or regressive Mississippian biothems on either flank of the TA suggests that it is inadvisable to impose the Mississippi Valley-derived eustasy curve on western flank depositional sequences.« less

Sediment Volume Record of Paleogene-Neogene Transantarctic Mountains Erosion and Landscape Modification, McMurdo Sound Region, Antarctica

NASA Astrophysics Data System (ADS)

Hall, T.; Wilson, T. J.; Henrys, S.; Speece, M. A.

2016-12-01

The interplay of tectonics and climate is recorded in the sedimentary strata within Victoria Land Basin, McMurdo Sound, Antarctica. Patterns of Cenozoic sedimentation are documented from interpretation of seismic reflection profiles calibrated by drillhole data in McMurdo Sound, and these patterns provide enhanced constraints on the evolution of the coupled Transantarctic Mountains-West Antarctic Rift System and on ice sheet advance/retreat through multiple climate cycles. The research focuses on shifts from warm based to cold based ice sheets through the variable climate and ice sheet conditions that characterized the early to middle Miocene. The study seeks to test the view that cold based ice sheets in arid, polar deserts minimally erode the landscape by calculating sediment volumes for critical climatic intervals. Revised seismic mapping through McMurdo Sound has been completed, utilizing the seismic stratigraphic framework first established by Fielding et al. (2006) and new reflectors marking unconformities identified from the AND-2A core (Levy et al., 2016). Reflector age constraints are derived by tying surfaces to the Cape Roberts Project, CIROS-1, and AND-2A drillholes. Seismic facies coupled with AND-2A core provenance information provides insight into depositional mechanisms and ice sheet behavior. Seismic facies transitions occur across the major unconformity surfaces in the AND-2A core. Sediment volume calculations for subareas within McMurdo Sound where reflectors are most continuous indicate substantial decreases in preserved sediment volume between the Oligocene and Early Miocene sequences, and between the early and mid-Miocene sequences. Sediment volumes, used in combination with an ice sheet model in a backstacking procedure, provide constraints on landscape modification and further understanding of how landscapes erode under warm and cold based ice sheet regimes.

URANIUM LEACHING AND RECOVERY PROCESS

DOEpatents

McClaine, L.A.

1959-08-18

A process is described for recovering uranium from carbonate leach solutions by precipitating uranium as a mixed oxidation state compound. Uranium is recovered by adding a quadrivalent uranium carbon;te solution to the carbonate solution, adjusting the pH to 13 or greater, and precipitating the uranium as a filterable mixed oxidation state compound. In the event vanadium occurs with the uranium, the vanadium is unaffected by the uranium precipitation step and remains in the carbonate solution. The uranium-free solution is electrolyzed in the cathode compartment of a mercury cathode diaphragm cell to reduce and precipitate the vanadium.

Health Risk Assessment of Embedded Depleted Uranium: Behavior, Physiology, Histology and Biokenetic Modeling.

DTIC Science & Technology

1996-11-01

increased urinary excretion of beta2-microglobulin and various amino acids. In rats exposed subchronically to low doses (cumulative dose: 0.66 or 1.32 mg/kg...leakage or failure of tubule reabsorption. Urinary enzymes are sensitive, non- invasive markers of toxicity primarily in the kidney tubules46. NAG is a...42 Neuman, W.F., Urinary uranium as a measure of exposure hazard, Industrial. Med. Surgery, 19 (1950) 185-191. 43 Neuman, W.F., Fleming, R.W., Dounce

Effect of stress at dosing on organophosphate and heavy metal toxicity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jortner, Bernard S.

2008-11-15

This paper reviews recent studies assessing the effect of well-defined, severe, transient stress at dosing on two classical models of toxicity. These are the acute (anticholinesterase) toxicity seen following exposure to the organophosphate insecticide chlorpyrifos, and the nephrotoxicity elicited by the heavy metal depleted uranium, in rats. Stress was induced by periods of restraint and forced swimming in days to weeks preceding toxicant exposure. Forced swimming was far more stressful, as measured by marked, if transient, elevation of plasma corticosterone. This form of stress was administered immediately prior to administration of chlorpyrifos or depleted uranium. Chlorpyrifos (single 60 mg/kg subcutaneously)more » elicited marked inhibition of brain acetylcholinesterase 4-day post-dosing. Depleted uranium (single intramuscular doses of 0.1, 0.3 or 1.0 mg/kg uranium) elicited dose-dependent increase in kidney concentration of the metal, with associated injury to proximal tubular epithelium and increases in serum blood urea nitrogen and creatinine during the 30-day post-dosing period. Stress at dosing had no effect on these toxicologic endpoints.« less

Transport of U(VI) through sediments amended with phosphate to induce in situ uranium immobilization.

PubMed

Mehta, Vrajesh S; Maillot, Fabien; Wang, Zheming; Catalano, Jeffrey G; Giammar, Daniel E

2015-02-01

Phosphate amendments can be added to U(VI)-contaminated subsurface environments to promote in situ remediation. The primary objective of this study was to evaluate the impacts of phosphate addition on the transport of U(VI) through contaminated sediments. In batch experiments using sediments (<2 mm size fraction) from a site in Rifle, Colorado, U(VI) only weakly adsorbed due to the dominance of the aqueous speciation by Ca-U(VI)-carbonate complexes. Column experiments with these sediments were performed with flow rates that correspond to a groundwater velocity of 1.1 m/day. In the absence of phosphate, the sediments took up 1.68-1.98 μg U/g of sediments when the synthetic groundwater influent contained 4 μM U(VI). When U(VI)-free influents were then introduced with and without phosphate, substantially more uranium was retained within the column when phosphate was present in the influent. Sequential extractions of sediments from the columns revealed that uranium was uniformly distributed along the length of the columns and was primarily in forms that could be extracted by ion exchange and contact with a weak acid. Laser induced fluorescence spectroscopy (LIFS) analysis along with sequential extraction results suggest adsorption as the dominant uranium uptake mechanism. The response of dissolved uranium concentrations to stopped-flow events and the comparison of experimental data with simulations from a simple reactive transport model indicated that uranium adsorption to and desorption from the sediments was not always at local equilibrium. Copyright © 2014 Elsevier Ltd. All rights reserved.

Plutonium recovery from spent reactor fuel by uranium displacement

DOEpatents

Ackerman, John P.

1992-01-01

A process for separating uranium values and transuranic values from fission products containing rare earth values when the values are contained together in a molten chloride salt electrolyte. A molten chloride salt electrolyte with a first ratio of plutonium chloride to uranium chloride is contacted with both a solid cathode and an anode having values of uranium and fission products including plutonium. A voltage is applied across the anode and cathode electrolytically to transfer uranium and plutonium from the anode to the electrolyte while uranium values in the electrolyte electrolytically deposit as uranium metal on the solid cathode in an amount equal to the uranium and plutonium transferred from the anode causing the electrolyte to have a second ratio of plutonium chloride to uranium chloride. Then the solid cathode with the uranium metal deposited thereon is removed and molten cadmium having uranium dissolved therein is brought into contact with the electrolyte resulting in chemical transfer of plutonium values from the electrolyte to the molten cadmium and transfer of uranium values from the molten cadmium to the electrolyte until the first ratio of plutonium chloride to uranium chloride is reestablished.

Kinetic, equilibrium and thermodynamic studies on sorption of uranium and thorium from aqueous solutions by a selective impregnated resin containing carminic acid.

PubMed

Rahmani-Sani, Abolfazl; Hosseini-Bandegharaei, Ahmad; Hosseini, Seyyed-Hossein; Kharghani, Keivan; Zarei, Hossein; Rastegar, Ayoob

2015-04-09

In this work, the removal of uranium and thorium ions from aqueous solutions was studied by solid-liquid extraction using an advantageous extractant-impregnated resin (EIR) prepared by loading carminic acid (CA) onto Amberlite XAD-16 resin beads. Batch sorption experiments using CA/XAD-16 beads for the removal of U(VI) and Th(IV) ions were carried out as a function of several parameters, like equilibration time, metal ion concentration, etc. The equilibrium data obtained from the sorption experiments were adjusted to the Langmuir isotherm model and the calculated maximum sorption capacities in terms of monolayer sorption were in agreement with those obtained from the experiments. The experimental data on the sorption behavior of both metal ions onto the EIR beads fitted well in both Bangham and intra-particle diffusion kinetic models, indicating that the intra-particle diffusion is the rate-controlling step. The thermodynamic studies at different temperatures revealed the feasibility and the spontaneous nature of the sorption process for both uranium and thorium ions. Copyright © 2014 Elsevier B.V. All rights reserved.

Three-dimensional inversion of magnetotelluric data for mineral exploration: An example from the McArthur River uranium deposit, Saskatchewan, Canada

NASA Astrophysics Data System (ADS)

Farquharson, Colin G.; Craven, James A.

2009-08-01

Shallow exploration targets are becoming scarce, meaning interest is turning towards deeper targets. The magnetotelluric method has the necessary depth capability, unlike many of the controlled-source electromagnetic prospecting techniques traditionally used. The geological setting of ore deposits is usually complex, requiring three-dimensional Earth models for their representation. An example of the applicability of three-dimensional inversion of magnetotelluric data to mineral exploration is presented here. Inversions of an audio-magnetotelluric data-set from the McArthur River uranium mine in the Athabasca Basin were carried out. A sub-set comprising data from eleven frequencies distributed over almost three decades was inverted. The form of the data used in the inversion was impedance. All four elements of the tensor were included. No decompositions of the data were done, nor rotation to a preferred strike direction, nor correction for static shifts. The inversions were successful: the observations were adequately reproduced and the main features in the conductivity model corresponded to known geological features. These included the graphitic basement fault along which the McArthur River uranium deposit is located.

Method of preparation of uranium nitride

DOEpatents

Kiplinger, Jaqueline Loetsch; Thomson, Robert Kenneth James

2013-07-09

Method for producing terminal uranium nitride complexes comprising providing a suitable starting material comprising uranium; oxidizing the starting material with a suitable oxidant to produce one or more uranium(IV)-azide complexes; and, sufficiently irradiating the uranium(IV)-azide complexes to produce the terminal uranium nitride complexes.

Theoretical prediction of the structural properties of uranium chalcogenides under high pressure

NASA Astrophysics Data System (ADS)

Kapoor, Shilpa; Yaduvanshi, Namrata; Singh, Sadhna

2018-05-01

Uranium chalcogenides crystallize in rock salt structure at normal condition and transform to Cesium Chloride structure at high pressure. We have investigated the transition pressure and volume drop of USe and UTe using three body potential model (TBIP). Present model includes long range Columbic, three body interaction forces and short range overlap forces operative up to next nearest neighbors. We have reported the phase transition pressure, relative volume collapses, the thermo physical properties such as molecular force constant (f), infrared absorption frequency (v0), Debye temperature (θD) and Gruneisen parameter (γ) of present chalcogenides and found that our results in general good agreement with experimental and other theoretical data.

10 CFR 760.1 - Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly (AEC) Domestic Uranium Program Circular 8, 10 CFR 60.8). 760.1 Section 760.1 Energy DEPARTMENT OF ENERGY DOMESTIC URANIUM PROGRAM § 760.1 Uranium leases on lands...

10 CFR 760.1 - Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 4 2013-01-01 2013-01-01 false Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly (AEC) Domestic Uranium Program Circular 8, 10 CFR 60.8). 760.1 Section 760.1 Energy DEPARTMENT OF ENERGY DOMESTIC URANIUM PROGRAM § 760.1 Uranium leases on lands...

10 CFR 760.1 - Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly (AEC) Domestic Uranium Program Circular 8, 10 CFR 60.8). 760.1 Section 760.1 Energy DEPARTMENT OF ENERGY DOMESTIC URANIUM PROGRAM § 760.1 Uranium leases on lands...

10 CFR 760.1 - Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly (AEC) Domestic Uranium Program Circular 8, 10 CFR 60.8). 760.1 Section 760.1 Energy DEPARTMENT OF ENERGY DOMESTIC URANIUM PROGRAM § 760.1 Uranium leases on lands...

10 CFR 760.1 - Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Uranium leases on lands controlled by DOE. (Domestic Uranium Program Circular No. 760.1, formerly (AEC) Domestic Uranium Program Circular 8, 10 CFR 60.8). 760.1 Section 760.1 Energy DEPARTMENT OF ENERGY DOMESTIC URANIUM PROGRAM § 760.1 Uranium leases on lands...

PROCESS OF PRODUCING REFRACTORY URANIUM OXIDE ARTICLES

DOEpatents

Hamilton, N.E.

1957-12-01

A method is presented for fabricating uranium oxide into a shaped refractory article by introducing a uranium halide fluxing reagent into the uranium oxide, and then mixing and compressing the materials into a shaped composite mass. The shaped mass of uranium oxide and uranium halide is then fired at an elevated temperature so as to form a refractory sintered article. It was found in the present invention that the introduction of a uraninm halide fluxing agent afforded a fluxing action with the uranium oxide particles and that excellent cohesion between these oxide particles was obtained. Approximately 90% of uranium dioxide and 10% of uranium tetrafluoride represent a preferred composition.

31 CFR 540.309 - Natural uranium.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 3 2013-07-01 2013-07-01 false Natural uranium. 540.309 Section 540... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.309 Natural uranium. The term natural uranium means uranium found in...

31 CFR 540.309 - Natural uranium.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance:Treasury 3 2014-07-01 2014-07-01 false Natural uranium. 540.309 Section 540... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.309 Natural uranium. The term natural uranium means uranium found in...

31 CFR 540.309 - Natural uranium.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 3 2012-07-01 2012-07-01 false Natural uranium. 540.309 Section 540... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.309 Natural uranium. The term natural uranium means uranium found in...

Final Report, University of California Merced: Uranium and strontium fate in waste-weathered sediments: Scaling of molecular processes to predict reactive transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chorover, Jon; Mueller, Karl; O'Day, Peggy Anne

2016-06-30

Objectives of the Project: 1. Determine the process coupling that occurs between mineral transformation and contaminant (U and Sr) speciation in acid-uranium waste weathered Hanford sediments. 2. Establish linkages between molecular-scale contaminant speciation and meso-scale contaminant lability, release and reactive transport. 3. Make conjunctive use of molecular- to bench-scale data to constrain the development of a mechanistic, reactive transport model that includes coupling of contaminant sorption-desorption and mineral transformation reactions. Hypotheses Tested: Uranium and strontium speciation in legacy sediments from the U-8 and U-12 Crib sites can be reproduced in bench-scale weathering experiments conducted on unimpacted Hanford sediments from themore » same formations; Reactive transport modeling of future uranium and strontium releases from the vadose zone of acid-waste weathered sediments can be effectively constrained by combining molecular-scale information on contaminant bonding environment with grain-scale information on contaminant phase partitioning, and meso-scale kinetic data on contaminant release from the waste-weathered porous media; Although field contamination and laboratory experiments differ in their diagenetic time scales (decades for field vs. months to years for lab), sediment dissolution, neophase nucleation, and crystal growth reactions that occur during the initial disequilibrium induced by waste-sediment interaction leave a strong imprint that persists over subsequent longer-term equilibration time scales and, therefore, give rise to long-term memory effects. Enabling Capabilities Developed: Our team developed an iterative measure-model approach that is broadly applicable to elucidate the mechanistic underpinnings of reactive contaminant transport in geomedia subject to active weathering.« less

Hydrocarbon-mediated gold and uranium concentration in the Witwatersrand Basin, South Africa

NASA Astrophysics Data System (ADS)

Fuchs, Sebastian; Williams-Jones, Anthony; Schumann, Dirk; Couillard, Martin; Murray, Andrew

2016-04-01

The Witwatersrand deposits in South Africa represent the largest repository of gold in the World and a major resource of uranium. The genesis of the gold and uranium ores in the quartz-pebble conglomerates (reefs), however, is still a matter of considerable discussion. Opinion has been divided over whether they represent paleo-placers that have been partly remobilised by hydrothermal fluids or if the mineralisation is entirely hydrothermal in origin. In addition, recently published models have proposed a syngenetic origin for the gold involving bacterially-mediated precipitation from meteoric water and shallow seawater. An important feature of the gold and uranium mineralisation in the reefs is the strong spatial association with organic matter. In some reefs, up to 70% of the gold and almost the entire uranium resource is spatially associated with pyrobitumen seams, suggesting a genetic relationship of the gold-uranium mineralisation with hydrocarbons. Here we report results of a study of the Carbon Leader Reef, using high-resolution scanning and transmission electron microscopy (SEM / TEM) and LA-ICP-MS that provide new insights into the role of hydrocarbons in the concentration of the gold and uranium. A detailed examination revealed gold monocrystals containing numerous rounded or elliptical inclusions filled with pyrobitumen. We interpret these inclusions to record the crystallisation of the gold around droplets of a hydrocarbon liquid that migrated through the Witwatersrand basin, and was converted to pyrobitumen by being heated. We propose that the gold was transported in a hydrothermal fluid as a bisulphide complex and that this fluid mixed with the hydrocarbon liquid to form a water-oil emulsion. The interaction between the two fluids caused a sharp reduction in fO2 at the water-oil interface, which destabilised the gold-bisulphide complexes, causing gold monocrystals to precipitate around the oil droplets. In contrast to the gold, uraninite, the principal uranium mineral, occurs as complex-shaped grains that represent aggregates containing billions of uraninite nanocrystals (5 - 7 nm in diameter), which grew in situ in the pyrobitumen matrix or more likely its liquid precursor (Fuchs et al., 2015). This in situ growth of isolated nanocrystalline aggregates shows that uranium was mobilised and concentrated by liquid hydrocarbons, and that uraninite nanocrystals were released from the oils during the conversion of oil to pyrobitumen. Our study provides new insights into the complex mechanisms of ore formation in the Witwatersrand Supergroup and compelling evidence that hydrocarbons played a major role in the concentration of the gold and uranium. It does not rule out the possibility that gold and uranium were introduced into the Witwatersrand Basin as detrital grains but shows that mobilisation of gold and uranium by hydrothermal fluids and hydrocarbon liquids, respectively, and the mixing of these fluids, were essential to ore formation. Fuchs, S., Schumann, D., Williams-Jones, A.E., Vali, H., 2015. The growth and concentration of uranium and titanium minerals in hydrocarbons of the Carbon Leader Reef, Witwatersrand Supergroup, South Africa. Chemical Geology 393-394, 55-66.

Uranium Pyrophoricity Phenomena and Prediction (FAI/00-39)

DOE Office of Scientific and Technical Information (OSTI.GOV)

PLYS, M.G.

2000-10-10

The purpose of this report is to provide a topical reference on the phenomena and prediction of uranium pyrophoricity for the Hanford Spent Nuclear Fuel (SNF) Project with specific applications to SNF Project processes and situations. Spent metallic uranium nuclear fuel is currently stored underwater at the K basins in the Hanford 100 area, and planned processing steps include: (1) At the basins, cleaning and placing fuel elements and scrap into stainless steel multi-canister overpacks (MCOs) holding about 6 MT of fuel apiece; (2) At nearby cold vacuum drying (CVD) stations, draining, vacuum drying, and mechanically sealing the MCOs; (3)more » Shipping the MCOs to the Canister Storage Building (CSB) on the 200 Area plateau; and (4) Welding shut and placing the MCOs for interim (40 year) dry storage in closed CSB storage tubes cooled by natural air circulation through the surrounding vault. Damaged fuel elements have exposed and corroded fuel surfaces, which can exothermically react with water vapor and oxygen during normal process steps and in off-normal situations, A key process safety concern is the rate of reaction of damaged fuel and the potential for self-sustaining or runaway reactions, also known as uranium fires or fuel ignition. Uranium metal and one of its corrosion products, uranium hydride, are potentially pyrophoric materials. Dangers of pyrophoricity of uranium and its hydride have long been known in the U.S. Department of Energy (Atomic Energy Commission/DOE) complex and will be discussed more below; it is sufficient here to note that there are numerous documented instances of uranium fires during normal operations. The motivation for this work is to place the safety of the present process in proper perspective given past operational experience. Steps in development of such a perspective are: (1) Description of underlying physical causes for runaway reactions, (2) Modeling physical processes to explain runaway reactions, (3) Validation of the method against experimental data, (4) Application of the method to plausibly explain operational experience, and (5) Application of the method to present process steps to demonstrate process safety and margin. Essentially, the logic above is used to demonstrate that runaway reactions cannot occur during normal SNF Project process steps, and to illustrate the depth of the technical basis for such a conclusion. Some off-normal conditions are identified here that could potentially lead to runaway reactions. However, this document is not intended to provide an exhaustive analysis of such cases. In summary, this report provides a ''toolkit'' of models and approaches for analysis of pyrophoricity safety issues at Hanford, and the technical basis for the recommended approaches. A summary of recommended methods appears in Section 9.0.« less

Ten metre global sea-level change associated with South Atlantic Aptian salt deposition

NASA Technical Reports Server (NTRS)

Burke, Kevin; Sengor, A. M. Celal

1988-01-01

Catastrophic filling of the kind of subsea-level depression commonly formed during ocean opening and ocean closing is the only mechanism, other than glacial eustacy, capable of rapidly lowering sea level. Aptian evaporites overlying oceanic crust on both sides of the South Atlantic between the Walvis Ridge and the Niger Delta were deposited in such a basin by repeated spilling of ocean water. The final flooding of the South Atlantic north of the Walvis Ridge extracted about 14 x 10 to the 8th cu km of sea water from the world ocean and effected about 10 m of sea-level lowering. It is speculated that the middle Aptian unconformity, which is one of the more prominent world-wide unconformities, is associated with this sea-level drop of about 10 m. A corollary of this interpretation is that if the catastrophic sea-level lowerings during the Mesozoic era had amplitudes substantially greater than 10 m, then a glacial mechanism to explain them would seem inescapable although the stratigraphic record has not yet yielded any evidence of such glaciation.

Regional stratigraphic framework of the Lisburne Group of ANWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watts, K.F.; Carlson, R.C.; Harris, A.G.

1995-05-01

The Carboniferous Lisburne Group, a major carbonate platform succession, is widely exposed in the Brooks Range and forms an extensive hydrocarbon target in the subsurface of the North Slope of Alaska. Gradationally beneath carbonates of the Lisburne Group, terrigenous sediments of the Mississippian Endicott Group (conglomerate and sandstone of the Kekiktuk Formation overlain by the Kayak Shale) were derived from local and northern (Ellesmerian) source areas. Locally, at the Endicott-Lisburne transition, sandy limestones of the Itkilyariak Formation record another phase of siliciclastic influx that lies above and/or is a lateral equivalent of the Kayak Shale and Lisburne Group in areasmore » adjacent to paleotopographic highs. This siliciclastic to carbonate transition represents a major transgressive succession that onlaps northward over the sub-Mississippian unconformity, a regional angular unconformity and sequence boundary in northern Alaska. The age and nature of onlap depend upon the paleotopography of the underlying sub-Mississippian rocks and regional passive margin subsidence. The Lisburne Group is a thick succession of carbonate rocks subdivided into the Alapah Limestone and overlying Wahoo Limestone, both having informal members.« less

Deformation style of the Mesozoic sedimentary rocks in southern Thailand

NASA Astrophysics Data System (ADS)

Kanjanapayont, Pitsanupong

2014-10-01

Mesozoic sedimentary rocks in southern Thailand are widespread from NNE-SSW and N-S in Chumphon and Trang provinces. The Mesozoic stratigraphic units are the marine Triassic Sai Bon Formation and the non-marine Jurassic-Cretaceous Thung Yai Group, the latter subdivided into Khlong Min, Lam Thap, Sam Chom, and Phun Phin Formations. These units overlie Permian carbonate rocks with an angular unconformity, and are overlain unconformably by Cenozoic units and the Quaternary sediments. The Mesozoic rocks have been folded to form two huge first-ordered syncline or synclinoria, the Chumphon and Surat Thani-Krabi-Trang synclinoria. These synclinoria are elongated in NNE-SSW to N-S direction, and incorporate asymmetric lower-order parasitic folds. The folds have moderately to steeply dipping eastward limbs and more gently dipping westward limbs. These folds were transected by brittle fractures in four major directions. These geologic structures indicate WNW-ESE to E-W contraction with top-to-the-east simple shear at some time before the deposition of the Cenozoic sedimentary units. No major deformation has affected the rocks subsequently, apart from the formation of the fault-controlled Cenozoic basins.

The Jurassic section along McElmo Canyon in southwestern Colorado

USGS Publications Warehouse

O'Sullivan, Robert B.

1997-01-01

In McElmo Canyon, Jurassic rocks are 1500-1600 ft thick. Lower Jurassic rocks of the Glen Canyon Group include (in ascending order) Wingate Sandstone, Kayenta Formation and Navajo Sandstone. Middle Jurassic rocks are represented by the San Rafael Group, which includes the Entrada Sandstone and overlying Wanakah Formation. Upper Jurassic rocks comprise the Junction Creek Sandstone overlain by the Morrison Formation. The Burro Canyon Formation, generally considered to be Lower Cretaceous, may be Late Jurassic in the McElmo Canyon area and is discussed with the Jurassic. The Upper Triassic Chinle Formation in the subsurface underlies, and the Upper Cretaceous Dakota Sandstone overlies, the Jurassic section. An unconformity is present at the base of the Glen Canyon Group (J-0), at the base of the San Rafael Group (J-2), and at the base of the Junction Creek Sandstone (J-5). Another unconformity of Cretaceous age is at the base of the Dakota Sandstone. Most of the Jurassic rocks consist of fluviatile, lacustrine and eolian deposits. The basal part of the Entrada Sandstone and the Wanakah Formation may be of marginal marine origin.

Rapid Radiochemical Method for Isotopic Uranium in Building ...

EPA Pesticide Factsheets

Technical Fact Sheet Analysis Purpose: Qualitative analysis Technique: Alpha spectrometry Method Developed for: Uranium-234, uranium-235, and uranium-238 in concrete and brick samples Method Selected for: SAM lists this method for qualitative analysis of uranium-234, uranium-235, and uranium-238 in concrete or brick building materials. Summary of subject analytical method which will be posted to the SAM website to allow access to the method.

High-resolution mineralogical characterization and biogeochemical modeling of uranium reaction pathways at the FRC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen Zhu

2006-06-15

High-Resolution Mineralogical Characterization and Biogeochemical Modeling of Uranium Reduction Pathways at the Oak Ridge Field-Research Center (FRC) Chen Zhu, Indiana University, David R. Veblen, Johns Hopkins University We have successfully completed a proof-of-concept, one-year grant on a three-year proposal from the former NABIR program, and here we seek additional two-year funding to complete and publish the research. Using a state-of-the-art 300-kV, atomic resolution, Field Emission Gun Transmission Electron Microscope (TEM), we have successfully identified three categories of mineral hosts for uranium in contaminated soils: (1) iron oxides; (2) mixed manganese-iron oxides; and (3) uranium phosphates. Method development using parallel electronmore » energy loss spectroscopy (EELS) associated with the TEM shows great promise for characterizing the valence states of immobilized U during bioremediation. We have also collected 27 groundwater samples from two push-pull field biostimulation tests, which form two time series from zero to approximately 600 hours. The temporal evolution in major cations, anions, trace elements, and the stable isotopes 34S, 18O in sulfate, 15N in nitrate, and 13C in dissolved inorganic carbon (DIC) clearly show that biostimulation resulted in reduction of nitrate, Mn(IV), Fe(III), U(VI), sulfate, and Tc(VII), and these reduction reactions were intimately coupled with a complex network of inorganic reactions evident from alkalinity, pH, Na, K, Mg, and Ca concentrations. From these temporal trends, apparent zero order rates were regressed. However, our extensive suite of chemical and isotopic data sets, perhaps the first and only comprehensive data set available at the FRC, show that the derived rates from these field biostimulation experiments are composite and lump-sum rates. There were several reactions that were occurring at the same time but were masked by these pseudo-zero order rates. A reaction-path model comprising a total of nine redox couples (NO3–/NH4+, MnO2(s)/Mn2+, Fe(OH)3(s) /Fe2+, TcO4–/TcO2(s), UO22+/UO2(s), SO42–/HS–, CO2/CH4, ethanol/acetate, and H+/H2.) is used to simulate the temporal biogeochemical evolution observed in the field tests. Preliminary results show that the models based on thermodynamics and more complex rate laws can generate the apparent zero order rates when several concurrent or competing reactions occur. Professor Alex Halliday of Oxford University, UK, and his postdoctoral associates are measuring the uranium isotopes in our groundwater samples. Newly developed state-of-the-art analytical techniques in measuring variability in 235U/238U offer the potential to distinguish biotic and abiotic uranium reductive mechanisms.« less